An evaluation of estimation methods for determining addition in presbyopes

Directory of Open Access Journals (Sweden)

Leonardo Catunda Bittencourt

2013-08-01

Full Text Available PURPOSE: The optical correction of presbyopia must be handled individually. Our aim was to compare the methods used in addition to the refractive near vision, with the final addition used in presbyopic patients. METHODS: Eighty healthy subjects with a mean age of 49.7 years (range 40 to 60 years were studied. Tentative near additions were determined using four different techniques: one-half amplitude accommodation with minus lenses (AAL; one-third accommodative demand with positive lens (ADL; balanced range of accommodation with minus and positive lenses (BRA and crossed cylinder test with initial myopisation (CCT. The power of the addition was then refined to arrive at the final addition. RESULTS: The mean tentative near additions were lower than the final addition for ADL and BRA addition methods. The mean differences between tentative and final additions were low for all the tests examined (less than 0.25 D. The intervals between the 95% limits of agreement differed substantially and were always higher than ±0.50 D. CONCLUSION: All the methods used displayed similar behavior and provided a tentative addition close to the final addition. The coefficient of agreements (COA detected suggests that every tentative addition should be adjusted according to the particular needs of the patient.

How many scientific papers are mentioned in policy-related documents? An empirical investigation using Web of Science and Altmetric data.

Science.gov (United States)

Haunschild, Robin; Bornmann, Lutz

2017-01-01

In this short communication, we provide an overview of a relatively newly provided source of altmetrics data which could possibly be used for societal impact measurements in scientometrics. Recently, Altmetric-a start-up providing publication level metrics-started to make data for publications available which have been mentioned in policy-related documents. Using data from Altmetric, we study how many papers indexed in the Web of Science (WoS) are mentioned in policy-related documents. We find that less than 0.5% of the papers published in different subject categories are mentioned at least once in policy-related documents. Based on our results, we recommend that the analysis of (WoS) publications with at least one policy-related mention is repeated regularly (annually) in order to check the usefulness of the data. Mentions in policy-related documents should not be used for impact measurement until new policy-related sites are tracked.

An evaluation of estimation methods for determining addition in presbyopes.

Science.gov (United States)

Bittencourt, Leonardo Catunda; Alves, Milton Ruiz; Dantas, Daniel Oliveira; Rodrigues, Pablo Felipe; Santos-Neto, Edson dos

2013-01-01

The optical correction of presbyopia must be handled individually. Our aim was to compare the methods used in addition to the refractive near vision, with the final addition used in presbyopic patients. Eighty healthy subjects with a mean age of 49.7 years (range 40 to 60 years) were studied. Tentative near additions were determined using four different techniques: one-half amplitude accommodation with minus lenses (AAL); one-third accommodative demand with positive lens (ADL); balanced range of accommodation with minus and positive lenses (BRA) and crossed cylinder test with initial myopisation (CCT). The power of the addition was then refined to arrive at the final addition. The mean tentative near additions were lower than the final addition for ADL and BRA addition methods. The mean differences between tentative and final additions were low for all the tests examined (less than 0.25 D). The intervals between the 95% limits of agreement differed substantially and were always higher than ±0.50 D. All the methods used displayed similar behavior and provided a tentative addition close to the final addition. The coefficient of agreements (COA) detected suggests that every tentative addition should be adjusted according to the particular needs of the patient.

Supplier Selection Using Weighted Utility Additive Method

Science.gov (United States)

Karande, Prasad; Chakraborty, Shankar

2015-10-01

Supplier selection is a multi-criteria decision-making (MCDM) problem which mainly involves evaluating a number of available suppliers according to a set of common criteria for choosing the best one to meet the organizational needs. For any manufacturing or service organization, selecting the right upstream suppliers is a key success factor that will significantly reduce purchasing cost, increase downstream customer satisfaction and improve competitive ability. The past researchers have attempted to solve the supplier selection problem employing different MCDM techniques which involve active participation of the decision makers in the decision-making process. This paper deals with the application of weighted utility additive (WUTA) method for solving supplier selection problems. The WUTA method, an extension of utility additive approach, is based on ordinal regression and consists of building a piece-wise linear additive decision model from a preference structure using linear programming (LP). It adopts preference disaggregation principle and addresses the decision-making activities through operational models which need implicit preferences in the form of a preorder of reference alternatives or a subset of these alternatives present in the process. The preferential preorder provided by the decision maker is used as a restriction of a LP problem, which has its own objective function, minimization of the sum of the errors associated with the ranking of each alternative. Based on a given reference ranking of alternatives, one or more additive utility functions are derived. Using these utility functions, the weighted utilities for individual criterion values are combined into an overall weighted utility for a given alternative. It is observed that WUTA method, having a sound mathematical background, can provide accurate ranking to the candidate suppliers and choose the best one to fulfill the organizational requirements. Two real time examples are illustrated to prove

Leading causes of death among decedents with mention of schizophrenia on the death certificates in the United States.

Science.gov (United States)

Lin, Jin-Jia; Liang, Fu-Weng; Li, Chung-Yi; Lu, Tsung-Hsueh

2018-01-30

Little is known about the changes in the ranking of leading cause of death (COD) among people died with schizophrenia across years in the United States (U.S.). This study aims to determine the ranking of leading COD among U.S. decedents with mention of schizophrenia by age from 2000 to 2015. The mortality multiple COD files maintained by the National Center for Health Statistics were used to identify decedents aged 15 years old and above with mention of schizophrenia anywhere on the death certificates to determine the number and proportion of deaths attributed to various underlying CODs. Of 13,289, 13,655, 14,135, and 15,033 people who died in 2000-2003, 2004-2007, 2008-2011and 2012-2015 with mention of schizophrenia, similar to all decedents, heart disease and cancer was the first and the second leading COD throughout the study years. Schizophrenia ranked the third in most years except in 2004-2007. The first leading COD for decedents with mention of schizophrenia aged 15-24, 25-44, 45-64, 65-74, and 75+ years old in 2012-2015 was suicide, accidents, heart disease, heart disease, and Alzheimer's disease and related dementia, respectively. Nevertheless, it was accidents, accidents, cancer, cancer, and heart disease, respectively for all decedents. The ranking of leading CODs among U.S. decedents with mention of schizophrenia changed across years and differed from all decedents by age, which suggest that different interventions should be designed accordingly. Copyright © 2018. Published by Elsevier B.V.

Stephen Hawking's Community-Bound Voice A Functional Investigation of Self-Mentions in Stephen Hawking's Scientific Prose

Directory of Open Access Journals (Sweden)

Davud Kuhi

2015-11-01

Full Text Available Thanks to the development of the concept of metadiscourse, it is now widely acknowledged that academic/scientific writing is not only concerned with communicating purely propositional meanings: what is communicated through academic/scientific communication is seen to be intertwined with the negotiation of social and interpersonal meanings. While a large number of so called metadiscoursal resources contribute to the simultaneous negotiation of propositional and interpersonal meanings, the present study aimed at investigating the functions self-mention forms can fulfill in academic/scientific communication. Two of Stephen Hawking's scientific books were selected as the corpus of the research, and based on Tang and John's (1999 model, the constructed corpus was analyzed in terms of the functions self-mention forms can fulfill in academic/scientific writing. The findings revealed that from among the different roles identified by Tang and John, the representative role constituted the most frequent self-mention function in the corpus. The remarkably heavy presence of representative role in Hawking's scientific prose was interpreted as a further evidence for the claim that scientists are more likely to persuade readers of their ideas if they frame their messages in ways which appeal to appropriate community-recognized relationships.

Brand Mentions in Social Media as a Key Performance Indicator in the German Fast Moving Consumer Goods Industry

OpenAIRE

Olga AZARKINA; Monyédodo KPOSSA; Erhard LICK

2014-01-01

This research aims to explore correlations between consumer-generated social media activity and the level of sales of German brands from the fast moving consumer goods industry. In particular, the objective was to examine whether there is a correlation between the number of brand mentions in social media and the sales of these products. The results indicate that the number of brand mentions and sales correlate positively in relation to products from the food and beverages category while this ...

Additive manufacturing method for SRF components of various geometries

Science.gov (United States)

Rimmer, Robert; Frigola, Pedro E; Murokh, Alex Y

2015-05-05

An additive manufacturing method for forming nearly monolithic SRF niobium cavities and end group components of arbitrary shape with features such as optimized wall thickness and integral stiffeners, greatly reducing the cost and technical variability of conventional cavity construction. The additive manufacturing method for forming an SRF cavity, includes atomizing niobium to form a niobium powder, feeding the niobium powder into an electron beam melter under a vacuum, melting the niobium powder under a vacuum in the electron beam melter to form an SRF cavity; and polishing the inside surface of the SRF cavity.

Using Nonexperts for Annotating Pharmacokinetic Drug-Drug Interaction Mentions in Product Labeling: A Feasibility Study.

Science.gov (United States)

Hochheiser, Harry; Ning, Yifan; Hernandez, Andres; Horn, John R; Jacobson, Rebecca; Boyce, Richard D

2016-04-11

Because vital details of potential pharmacokinetic drug-drug interactions are often described in free-text structured product labels, manual curation is a necessary but expensive step in the development of electronic drug-drug interaction information resources. The use of nonexperts to annotate potential drug-drug interaction (PDDI) mentions in drug product label annotation may be a means of lessening the burden of manual curation. Our goal was to explore the practicality of using nonexpert participants to annotate drug-drug interaction descriptions from structured product labels. By presenting annotation tasks to both pharmacy experts and relatively naïve participants, we hoped to demonstrate the feasibility of using nonexpert annotators for drug-drug information annotation. We were also interested in exploring whether and to what extent natural language processing (NLP) preannotation helped improve task completion time, accuracy, and subjective satisfaction. Two experts and 4 nonexperts were asked to annotate 208 structured product label sections under 4 conditions completed sequentially: (1) no NLP assistance, (2) preannotation of drug mentions, (3) preannotation of drug mentions and PDDIs, and (4) a repeat of the no-annotation condition. Results were evaluated within the 2 groups and relative to an existing gold standard. Participants were asked to provide reports on the time required to complete tasks and their perceptions of task difficulty. One of the experts and 3 of the nonexperts completed all tasks. Annotation results from the nonexpert group were relatively strong in every scenario and better than the performance of the NLP pipeline. The expert and 2 of the nonexperts were able to complete most tasks in less than 3 hours. Usability perceptions were generally positive (3.67 for expert, mean of 3.33 for nonexperts). The results suggest that nonexpert annotation might be a feasible option for comprehensive labeling of annotated PDDIs across a broader

Evaluation of the H-point standard additions method (HPSAM) and the generalized H-point standard additions method (GHPSAM) for the UV-analysis of two-component mixtures.

Science.gov (United States)

Hund, E; Massart, D L; Smeyers-Verbeke, J

1999-10-01

The H-point standard additions method (HPSAM) and two versions of the generalized H-point standard additions method (GHPSAM) are evaluated for the UV-analysis of two-component mixtures. Synthetic mixtures of anhydrous caffeine and phenazone as well as of atovaquone and proguanil hydrochloride were used. Furthermore, the method was applied to pharmaceutical formulations that contain these compounds as active drug substances. This paper shows both the difficulties that are related to the methods and the conditions by which acceptable results can be obtained.

CT image segmentation methods for bone used in medical additive manufacturing.

Science.gov (United States)

van Eijnatten, Maureen; van Dijk, Roelof; Dobbe, Johannes; Streekstra, Geert; Koivisto, Juha; Wolff, Jan

2018-01-01

The accuracy of additive manufactured medical constructs is limited by errors introduced during image segmentation. The aim of this study was to review the existing literature on different image segmentation methods used in medical additive manufacturing. Thirty-two publications that reported on the accuracy of bone segmentation based on computed tomography images were identified using PubMed, ScienceDirect, Scopus, and Google Scholar. The advantages and disadvantages of the different segmentation methods used in these studies were evaluated and reported accuracies were compared. The spread between the reported accuracies was large (0.04 mm - 1.9 mm). Global thresholding was the most commonly used segmentation method with accuracies under 0.6 mm. The disadvantage of this method is the extensive manual post-processing required. Advanced thresholding methods could improve the accuracy to under 0.38 mm. However, such methods are currently not included in commercial software packages. Statistical shape model methods resulted in accuracies from 0.25 mm to 1.9 mm but are only suitable for anatomical structures with moderate anatomical variations. Thresholding remains the most widely used segmentation method in medical additive manufacturing. To improve the accuracy and reduce the costs of patient-specific additive manufactured constructs, more advanced segmentation methods are required. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Chemical sensors and the development of potentiometric methods for liquid media analysis

International Nuclear Information System (INIS)

Vlasov, Yu.G.; Kolodnikov, V.V.; Ermolenko, Yu.E.; Mikhajlova, S.S.

1996-01-01

Aspects of applying indirect potentiometric determination to chemical analysis are considered. Among them are the standard and modified addition and subtraction methods, the multiple addition method, and potentiometric titration using ion-selective electrodes as indicators. These methods significantly extend the capabilities of ion-selective potentiometric analysis. Conditions for the applicability of the above-mentioned methods to various samples (Cd, REE, Th, iodides and others) are discussed using all available ion-selective electrodes as examples. 162 refs., 2 figs., 5 tabs

Learning Method and Its Influence on Nutrition Study Results Throwing the Ball

Science.gov (United States)

Samsudin; Nugraha, Bayu

2015-01-01

This study aimed to know the difference between playing and learning methods of exploratory learning methods to learning outcomes throwing the ball. In addition, this study also aimed to determine the effect of nutritional status of these two learning methods mentioned above. This research was conducted at SDN Cipinang Besar Selatan 16 Pagi East…

Public hospital quality report awareness: evidence from National and Californian Internet searches and social media mentions, 2012.

Science.gov (United States)

Huesch, Marco D; Currid-Halkett, Elizabeth; Doctor, Jason N

2014-03-11

Publicly available hospital quality reports seek to inform consumers of important healthcare quality and affordability attributes, and may inform consumer decision-making. To understand how much consumers search for such information online on one Internet search engine, whether they mention such information in social media and how positively they view this information. A leading Internet search engine (Google) was the main focus of the study. Google Trends and Google Adwords keyword analyses were performed for national and Californian searches between 1 August 2012 and 31 July 2013 for keywords related to 'top hospital', best hospital', and 'hospital quality', as well as for six specific hospital quality reports. Separately, a proprietary social media monitoring tool was used to investigate blog, forum, social media and traditional media mentions of, and sentiment towards, major public reports of hospital quality in California in 2012. (1) Counts of searches for keywords performed on Google; (2) counts of and (3) sentiment of mentions of public reports on social media. National Google search volume for 75 hospital quality-related terms averaged 610 700 searches per month with strong variation by keyword and by state. A commercial report (Healthgrades) was more commonly searched for nationally on Google than the federal government's Hospital Compare, which otherwise dominated quality-related search terms. Social media references in California to quality reports were generally few, and commercially produced hospital quality reports were more widely mentioned than state (Office of Statewide Healthcare Planning and Development (OSHPD)), or non-profit (CalHospitalCompare) reports. Consumers are somewhat aware of hospital quality based on Internet search activity and social media disclosures. Public stakeholders may be able to broaden their quality dissemination initiatives by advertising on Google or Twitter and using social media interactively with consumers looking

Public hospital quality report awareness: evidence from National and Californian Internet searches and social media mentions, 2012

Science.gov (United States)

Huesch, Marco D; Currid-Halkett, Elizabeth; Doctor, Jason N

2014-01-01

Objectives Publicly available hospital quality reports seek to inform consumers of important healthcare quality and affordability attributes, and may inform consumer decision-making. To understand how much consumers search for such information online on one Internet search engine, whether they mention such information in social media and how positively they view this information. Setting and design A leading Internet search engine (Google) was the main focus of the study. Google Trends and Google Adwords keyword analyses were performed for national and Californian searches between 1 August 2012 and 31 July 2013 for keywords related to ‘top hospital’, best hospital’, and ‘hospital quality’, as well as for six specific hospital quality reports. Separately, a proprietary social media monitoring tool was used to investigate blog, forum, social media and traditional media mentions of, and sentiment towards, major public reports of hospital quality in California in 2012. Primary outcome measures (1) Counts of searches for keywords performed on Google; (2) counts of and (3) sentiment of mentions of public reports on social media. Results National Google search volume for 75 hospital quality-related terms averaged 610 700 searches per month with strong variation by keyword and by state. A commercial report (Healthgrades) was more commonly searched for nationally on Google than the federal government's Hospital Compare, which otherwise dominated quality-related search terms. Social media references in California to quality reports were generally few, and commercially produced hospital quality reports were more widely mentioned than state (Office of Statewide Healthcare Planning and Development (OSHPD)), or non-profit (CalHospitalCompare) reports. Conclusions Consumers are somewhat aware of hospital quality based on Internet search activity and social media disclosures. Public stakeholders may be able to broaden their quality dissemination initiatives by

[Productivity of doctoral programs in Psychology with Quality Mention in journal articles included in Journal Citation Reports].

Science.gov (United States)

Musi-Lechuga, Bertha; Olivas-Ávila, José; Castro, Angel

2011-08-01

The main objective of the present study was to classify doctoral programs with Quality Mention in Psychology based on their scientific productivity. For this purpose, articles in the Web of Science published by professors teaching in these doctoral programs were analyzed. In addition, we analyzed scientific journals in which these professors tend to publish more papers and the evolution in the number of papers published until 2009. Results showed that the most productive doctoral program was the Neurosciences program at the University of Oviedo. This program showed a ratio of 40 articles--published in journals included in Journal Citation Reports--by each professor. In contrast, other programs did not reach a ratio of 10 articles per professor. Regarding journals, results showed that 9 out of the 20 most popular journals are Hispanic and a gradual increase in the number of published papers was also observed. Lastly, results and implications for quality assessment are discussed.

Additive manufacturing of reflective optics: evaluating finishing methods

Science.gov (United States)

Leuteritz, G.; Lachmayer, R.

2018-02-01

Individually shaped light distributions become more and more important in lighting technologies and thus the importance of additively manufactured reflectors increases significantly. The vast field of applications ranges from automotive lighting to medical imaging and bolsters the statement. However, the surfaces of additively manufactured reflectors suffer from insufficient optical properties even when manufactured using optimized process parameters for the Selective Laser Melting (SLM) process. Therefore post-process treatments of reflectors are necessary in order to further enhance their optical quality. This work concentrates on the effectiveness of post-process procedures for reflective optics. Based on already optimized aluminum reflectors, which are manufactured with a SLM machine, the parts are differently machined after the SLM process. Selected finishing methods like laser polishing, sputtering or sand blasting are applied and their effects quantified and compared. The post-process procedures are investigated on their impact on surface roughness and reflectance as well as geometrical precision. For each finishing method a demonstrator will be created and compared to a fully milled sample and among themselves. Ultimately, guidelines are developed in order to figure out the optimal treatment of additively manufactured reflectors regarding their optical and geometrical properties. Simulations of the light distributions will be validated with the developed demonstrators.

Comparison of prosthetic models produced by traditional and additive manufacturing methods.

Science.gov (United States)

Park, Jin-Young; Kim, Hae-Young; Kim, Ji-Hwan; Kim, Jae-Hong; Kim, Woong-Chul

2015-08-01

The purpose of this study was to verify the clinical-feasibility of additive manufacturing by comparing the accuracy of four different manufacturing methods for metal coping: the conventional lost wax technique (CLWT); subtractive methods with wax blank milling (WBM); and two additive methods, multi jet modeling (MJM), and micro-stereolithography (Micro-SLA). Thirty study models were created using an acrylic model with the maxillary upper right canine, first premolar, and first molar teeth. Based on the scan files from a non-contact blue light scanner (Identica; Medit Co. Ltd., Seoul, Korea), thirty cores were produced using the WBM, MJM, and Micro-SLA methods, respectively, and another thirty frameworks were produced using the CLWT method. To measure the marginal and internal gap, the silicone replica method was adopted, and the silicone images obtained were evaluated using a digital microscope (KH-7700; Hirox, Tokyo, Japan) at 140X magnification. Analyses were performed using two-way analysis of variance (ANOVA) and Tukey post hoc test (α=.05). The mean marginal gaps and internal gaps showed significant differences according to tooth type (Pmanufacturing method (Pmanufacturing methods were within a clinically allowable range, and, thus, the clinical use of additive manufacturing methods is acceptable as an alternative to the traditional lost wax-technique and subtractive manufacturing.

Brand Mentions in Social Media as a Key Performance Indicator in the German Fast Moving Consumer Goods Industry

Directory of Open Access Journals (Sweden)

Olga AZARKINA

2014-11-01

Full Text Available This research aims to explore correlations between consumer-generated social media activity and the level of sales of German brands from the fast moving consumer goods industry. In particular, the objective was to examine whether there is a correlation between the number of brand mentions in social media and the sales of these products. The results indicate that the number of brand mentions and sales correlate positively in relation to products from the food and beverages category while this is not the case with respect to the non-food product category. Hence, marketers need to promote consumer-generated social media activity particularly for food and beverages.

Collectors of botanical specimens from the flora area mentioned in the Flora of Ethiopia and Eritrea

DEFF Research Database (Denmark)

Friis, Ib

2009-01-01

Information based on all available sources about full name, nationality, profession, area and period of collection, with whom they are known to have made joint collections, herbaria in which the collections have been deposited etc., for all collectors mentioned in vol. 1-7 of the Flora of Ethiopi...

Food additives used in meat processing according to the Polish and European Union legislation.

Science.gov (United States)

Uradziński, J; Weiner, M

2003-01-01

This paper presents the legal regulations related to the use of food additives in meat production in Poland and the European Union. The Polish legal definition of food additives is given as well as the classification of permitted food additives added to food and stimulants by their technological function. In addition, a definition of processing aids in the food industry is included. It shows that Polish legislation includes food additives used to ensure or improve food nutritional value, whereas in the EU legislation, these substances are not included in the list of food additives. Moreover, the Council Directives include food additive specific purity criteria, whereas the Polish regulations do not mention the legal regulations of this issue in practice. The European Union use mechanisms and procedures for the introduction of new food additives into internal markets as well as controlling the circulation of additives. The Polish legislation in practice, however, does not determine approval or methods for the introduction of new food additives to the market. Legal regulations on the monitoring of food additives no exist.

Biological features produced by additive manufacturing processes using vat photopolymerization method

DEFF Research Database (Denmark)

Davoudinejad, Ali; Mendez Ribo, Macarena; Pedersen, David Bue

2017-01-01

of micro biological features by Additive Manufacturing (AM) processes. The study characterizes the additive manufacturing processes for polymeric micro part productions using the vat photopolymerization method. A specifically designed vat photopolymerization AM machine suitable for precision printing...

Occupational Portrayal of Men and Women on the Most Frequently Mentioned Television Shows of Preschool Children.

Science.gov (United States)

Shechtman, Stephen A.

The purpose of this study was to assess the distribution of male vs. female occupational portrayals in terms of occupational prestige on the six television shows most frequently mentioned by preschool children. The following shows were viewed and analyzed six times: Sesame Street, Bugs Bunny, Roadrunner, Batman, Flintstones, and Happy Days.…

DEVELOPMENT OF TOFU PRODUCTION METHOD WITH PROBIOTIC BACTERIA ADDITION

Directory of Open Access Journals (Sweden)

Dorota Zielińska

2015-06-01

Full Text Available The aim of the study was to develop a production method for tofu with probiotic bacteria under laboratory conditions. The works included: selection of a strain and tofu production conditions, and a storage test of the manufactured product. It was concluded that the sensory quality of tofu with the addition of different probiotic cultures did not differ significantly (p>0.01, depending on used strains and their mixtures, and the sample quality was comparable to the commercial product. It was observed that the number of Lactobacillus bacteria in study samples was the factor determining the palatability of tofu (r= 0.75. On the other hand, the sensory quality of products was significantly affected by the production method of tofu with the addition of probiotic bacteria. It was concluded that the formation of curds from soy beverage by the addition of CaSO4, followed by inoculation with Lactobacillus casei ŁOCK 0900 at the amount of 9.26 log CFU/g and incubation at temp. of 37C for 2h as well as for 20h are methods recommended for production tofu with regard to sensory qualities of the final product among all tested methods. The number of lactic acid bacteria in studied tofu samples was maintained at the high level (109-1010 CFU/g, and the number of Bifidobacterium animalis ssp lactis BB-12 bacteria did not exceed 103 CFU/g, whereas the number of Lactobacillus bacteria was equal to 108-109 CFU/g. For the period of 15 days of storage of tofu with probiotic bacteria at the temperature of 4C the number of lactic acid bacteria was maintained at the constant level of approx. 109 CFU/g. It was concluded that it is possible to produce tofu with probiotic bacteria that has acceptable sensory characteristics and a high number of lactic acid bacteria, therefore the product could be considered as a functional one.

The explicit mentioning of reporting guidelines in urogynecology journals in 2013: A bibliometric study.

Science.gov (United States)

Koch, Marianne; Riss, Paul; Umek, Wolfgang; Hanzal, Engelbert

2016-03-01

Poor reporting of research may limit critical appraisal and reproducibility, whereas adherence to reporting guidelines (RG) can guarantee completeness and transparency. We aimed to determine the explicit citing of RGs (CONSORT, PRISMA, STROBE) in urogynecology articles in 2013, the requirements of relevant journals and a potential difference between urogynecology and general gynecology journals. All urogynecologic articles published between January and December 2013 in the journals NAU, IUJ, FPMRS, GREEN, AJOG, and BJOG were included. Issues were searched for systematic reviews, RCTs, cohort studies, case-control studies and cross-sectional studies. Each electronic article was searched for the term PRISMA, CONSORT, or STROBE according to the study design. Instructions to Authors of the six journals were screened for requirement of using RGs. We included 296 articles (243 observational studies, 40 RCTs, and 13 systematic reviews). The use of PRISMA guidelines was explicitly declared in 54% of systematic reviews, CONSORT guidelines were referenced in 25% of RCTs and STROBE in 1.2% of observational studies. The use of CONSORT is required by all journals except FPMRS. PRISMA and STROBE are only compulsory in the journals GREEN, AJOG, and BJOG. The overall rate of explicit mentioning of RGs comparing urogynecology and general gynecology journals was 6.7% versus 7.1%, respectively. The explicit mentioning of RGs was on a relatively low level. A slightly higher adherence was recognized among general gynecology journals compared to urogynecology journals. Stronger efforts should be taken to further promote the use of RGs in urogynecology. © 2015 Wiley Periodicals, Inc.

H-point standard additions method for simultaneous determination of sulfamethoxazole and trimethoprim in pharmaceutical formulations and biological fluids with simultaneous addition of two analytes

Science.gov (United States)

Givianrad, M. H.; Saber-Tehrani, M.; Aberoomand-Azar, P.; Mohagheghian, M.

2011-03-01

The applicability of H-point standard additions method (HPSAM) to the resolving of overlapping spectra corresponding to the sulfamethoxazole and trimethoprim is verified by UV-vis spectrophotometry. The results show that the H-point standard additions method with simultaneous addition of both analytes is suitable for the simultaneous determination of sulfamethoxazole and trimethoprim in aqueous media. The results of applying the H-point standard additions method showed that the two drugs could be determined simultaneously with the concentration ratios of sulfamethoxazole to trimethoprim varying from 1:18 to 16:1 in the mixed samples. Also, the limits of detections were 0.58 and 0.37 μmol L -1 for sulfamethoxazole and trimethoprim, respectively. In addition the means of the calculated RSD (%) were 1.63 and 2.01 for SMX and TMP, respectively in synthetic mixtures. The proposed method has been successfully applied to the simultaneous determination of sulfamethoxazole and trimethoprim in some synthetic, pharmaceutical formulation and biological fluid samples.

Transport methods: general. 3. An Additive Angular-Dependent Re-balance Acceleration Method for Neutron Transport Equations

International Nuclear Information System (INIS)

Cho, Nam Zin; Park, Chang Je

2001-01-01

An additive angular-dependent re-balance (AADR) factor acceleration method is described to accelerate the source iteration of discrete ordinates transport calculation. The formulation of the AADR method follows that of the angular-dependent re-balance (ADR) method in that the re-balance factor is defined only on the cell interface and in that the low-order equation is derived by integrating the transport equation (high-order equation) over angular subspaces. But, the re-balance factor is applied additively. While the AADR method is similar to the boundary projection acceleration and the alpha-weighted linear acceleration, it is more general and does have distinct features. The method is easily extendible to DP N and low-order S N re-balancing, and it does not require consistent discretizations between the high- and low-order equations as in diffusion synthetic acceleration. We find by Fourier analysis and numerical results that the AADR method with a chosen form of weighting functions is unconditionally stable and very effective. There also exists an optimal weighting parameter that leads to the smallest spectral radius. The AADR acceleration method described in this paper is simple to implement, unconditionally stable, and very effective. It uses a physically based weighting function with an optimal parameter, leading to the best spectral radius of ρ<0.1865, compared to ρ<0.2247 of DSA. The application of the AADR acceleration method with the LMB scheme on a test problem shows encouraging results

Comparison of presbyopic additions determined by the fused cross-cylinder method using alternative target background colours.

Science.gov (United States)

Wee, Sung-Hyun; Yu, Dong-Sik; Moon, Byeong-Yeon; Cho, Hyun Gug

2010-11-01

To compare and contrast standard and alternative versions of refractor head (phoropter)-based charts used to determine reading addition. Forty one presbyopic subjects aged between 42 and 60 years were tested. Tentative additions were determined using a red-green background letter chart, and 4 cross-grid charts (with white, red, green, or red-green backgrounds) which were used with the fused cross cylinder (FCC) method. The final addition for a 40 cm working distance was determined for each subject by subjectively adjusting the tentative additions. There were significant differences in the tentative additions obtained using the 5 methods (repeated measures ANOVA, p FCC method. There were no significant differences between the tentative and final additions for the green background in the FCC method (p > 0.05). The intervals of the 95% limits of agreement were under ±0.50 D, and the narrowest interval (±0.26 D) was for the red-green background. The 3 FCC methods with a white, green, or red-green background provided a tentative addition close to the final addition. Compared with the other methods, the FCC method with the red-green background had a narrow range of error. Further, since this method combines the functions of both the fused cross-cylinder test and the duochrome test, it can be a useful technique for determining presbyopic additions. © 2010 The Authors. Ophthalmic and Physiological Optics © 2010 The College of Optometrists.

PRACTICE OF DEVELOPMENT OF STUDENTS’ ADDITIONAL INTERDISCIPLINARY COMPETENCIES IN A MODERN UNIVERSITY

Directory of Open Access Journals (Sweden)

E. G. Syryamkina

2016-01-01

Full Text Available The aim of the article is to show the possibilities of formation ofnew approaches to the development of additional interdisciplinary competencies of university youth in modern conditions.Methods. The methods involve such theoretical methods as analysis of scientific literature and documents, generalization of empirical data.Results and scientific novelty. The article includes experience of many years in the sphere of development of students’ additional interdisciplinary competencies of the National Research Tomsk State University (TSU. The authors present cases of two TSU structural subdivisions: Center for Social and Professional Volunteering and Park of Social and Humanitarian Technologies. The effective educational technologies proposed by the authors are analysed. Transition from the theoretical (knowledge training of students to practically-oriented training is an actual trend today. A graduate of a modern university should have a broad vision, communication skills, desire for cooperation, self-development, creative application of gained knowledge and lifelong learning, in other words –the development of students’ additional interdisciplinary competencies. In this regard, the role of students’ extracurricular practical work in a university is increasing. This work requires organizational and educational support. The article gives description and analysis of effective educational forms of technologies for development of students’ additional interdisciplinary competencies within their extracurricular activities in the mentioned above structural units of the university.Practical significance. Higher educational establishments can use presented materials for improvement of an educational process.

Method and arrangement of distillation of shales

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1920-03-29

A method is given of distilling shale and other bituminous materials utilizing the heat from the combustion of the residue, possibly with additional heat from other fuels. It is characterized by the shale, which is arranged in layers, being first submitted to a process of distillation utilizing the heat mentioned, and at the same time recovering the products of distillation, and second the shale being burned without disturbing the layers to any appreciable extent. The patent has 16 more claims.

ExSTA: External Standard Addition Method for Accurate High-Throughput Quantitation in Targeted Proteomics Experiments.

Science.gov (United States)

Mohammed, Yassene; Pan, Jingxi; Zhang, Suping; Han, Jun; Borchers, Christoph H

2018-03-01

Targeted proteomics using MRM with stable-isotope-labeled internal-standard (SIS) peptides is the current method of choice for protein quantitation in complex biological matrices. Better quantitation can be achieved with the internal standard-addition method, where successive increments of synthesized natural form (NAT) of the endogenous analyte are added to each sample, a response curve is generated, and the endogenous concentration is determined at the x-intercept. Internal NAT-addition, however, requires multiple analyses of each sample, resulting in increased sample consumption and analysis time. To compare the following three methods, an MRM assay for 34 high-to-moderate abundance human plasma proteins is used: classical internal SIS-addition, internal NAT-addition, and external NAT-addition-generated in buffer using NAT and SIS peptides. Using endogenous-free chicken plasma, the accuracy is also evaluated. The internal NAT-addition outperforms the other two in precision and accuracy. However, the curves derived by internal vs. external NAT-addition differ by only ≈3.8% in slope, providing comparable accuracies and precision with good CV values. While the internal NAT-addition method may be "ideal", this new external NAT-addition can be used to determine the concentration of high-to-moderate abundance endogenous plasma proteins, providing a robust and cost-effective alternative for clinical analyses or other high-throughput applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Infertility and surrogacy first mentioned on a 4000-year-old Assyrian clay tablet of marriage contract in Turkey.

Science.gov (United States)

Turp, Ahmet Berkiz; Guler, Ismail; Bozkurt, Nuray; Uysal, Aysel; Yilmaz, Bulent; Demir, Mustafa; Karabacak, Onur

2018-01-01

Mankind has been expressing the breeding topic for thousands of years. Reproduction is the primary instinct of human beings and it is a social, cultural, medical issue. Demographic infertility is one of them, which is defined infertility as the inability to become pregnant with a live birth, within five years of regular sexual contact based upon a consistent union status in marriage maintaining a desire for a child with the lack of contraceptive use and non-lactating. A first mentions about infertility and surrogacy is discovered on a 4000-year-old clay tablet of marriage contract belonging to the Assyrian period exhibited at Istanbul Archeology Museum in Turkey. In conclusion, there are many different ways to solve infertility problems like surrogacy as mentioned even 4000 years ago in this Assyrian clay tablet of marriage contract as the first time in the literature. Medical treatments in relation to human infertility will continue to be the focus of social and cultural debates. Hence, more legislation and regulation will come in many countries to control the unauthorized exploitation of the patient.

Comparison of oxytetracycline degradation behavior in pig manure with different antibiotic addition methods.

Science.gov (United States)

Wang, Yan; Chen, Guixiu; Liang, Juanboo; Zou, Yongde; Wen, Xin; Liao, Xindi; Wu, Yinbao

2015-12-01

Using manure collected from swine fed with diet containing antibiotics and antibiotic-free swine manure spiked with antibiotics are the two common methods of studying the degradation behavior of veterinary antibiotic in manure in the environment. However, few studies had been conducted to co-compare these two different antibiotic addition methods. This study used oxytetracycline (OTC) as a model antibiotic to study antibiotic degradation behavior in manure under the above two OTC addition methods. In addition, the role of microorganisms present in the manure on degradation behavior was also examined. The results showed that degradation half-life of OTC in manure from swine fed OTC (9.04 days) was significantly shorter than that of the manure directly treated with OTC (9.65 days). Concentration of 4-epi-OTC in manure from swine fed OTC peaked earlier than that in manure spiked with OTC, and the degradation rates of 4-epi-OTC and α-apo-OTC in the manure from swine fed OTC were faster, but the peak concentrations were lower, than those in manure spiked with OTC. Bacterial diversity and relative abundance of Bacillus cereus data demonstrated that sterilization of the manure before experiment significantly decreased OTC degradation rate in both of the addition methods. Results of the present study demonstrated that the presence of the metabolites (especially 4-epi-OTC) and microorganisms had significant influence on OTC degradation.

Influence of additives on microstructures, mechanical properties and shock-induced reaction characteristics of Al/Ni composites

Energy Technology Data Exchange (ETDEWEB)

Xiong, Wei; Zhang, Xianfeng, E-mail: lynx@mail.njust.edu.cn; Wu, Yang; He, Yong; Wang, Chuanting; Guo, Lei

2015-11-05

Granular composites containing aluminum (Al) and nickel (Ni) are typical structural energetic materials, which possess ideal combination of both mechanical properties and energy release capability. The influence of two additives, namely Teflon (PTFE) and copper (Cu), on mechanical properties and shock-induced chemical reaction (SICR) characteristics of Al/Ni material system has been investigated. Three composites, namely Al/Ni, Al/Ni/PTFE and Al/Ni/Cu with same volumetric ratio of Al powder to Ni powder, were processed by means of static pressing. Scanning electron microscopy was used to study the microstructure of the mentioned three composites. Quasi static compression tests were also conducted to determine the mechanical properties and fracture behavior of the mentioned three composites. It was shown that the additives affected both compressive strength and fracture mode of the three composites. Impact initiation experiments on the mentioned three composites were performed to determine their shock-induced chemical reaction characteristics by considering pressure histories measured in the test chamber. The experimental results showed that the additives had significant effects on critical initiation velocity, reaction rate, reaction efficiency and post-reaction behavior. - Highlights: • .Al/Ni, Al/Ni/PTFE and Al/Ni/Cu were processed by means of static pressing. • .Microstructures, mechanical properties and shock-induced reactions were studied. • .Microstructures affect both compressive strength and fracture mode. • .Impact velocity is an important factor in shock-induced chemical characteristics. • .Each additive has significant effects on energy release behavior.

Influence of additives on microstructures, mechanical properties and shock-induced reaction characteristics of Al/Ni composites

International Nuclear Information System (INIS)

Xiong, Wei; Zhang, Xianfeng; Wu, Yang; He, Yong; Wang, Chuanting; Guo, Lei

2015-01-01

Granular composites containing aluminum (Al) and nickel (Ni) are typical structural energetic materials, which possess ideal combination of both mechanical properties and energy release capability. The influence of two additives, namely Teflon (PTFE) and copper (Cu), on mechanical properties and shock-induced chemical reaction (SICR) characteristics of Al/Ni material system has been investigated. Three composites, namely Al/Ni, Al/Ni/PTFE and Al/Ni/Cu with same volumetric ratio of Al powder to Ni powder, were processed by means of static pressing. Scanning electron microscopy was used to study the microstructure of the mentioned three composites. Quasi static compression tests were also conducted to determine the mechanical properties and fracture behavior of the mentioned three composites. It was shown that the additives affected both compressive strength and fracture mode of the three composites. Impact initiation experiments on the mentioned three composites were performed to determine their shock-induced chemical reaction characteristics by considering pressure histories measured in the test chamber. The experimental results showed that the additives had significant effects on critical initiation velocity, reaction rate, reaction efficiency and post-reaction behavior. - Highlights: • .Al/Ni, Al/Ni/PTFE and Al/Ni/Cu were processed by means of static pressing. • .Microstructures, mechanical properties and shock-induced reactions were studied. • .Microstructures affect both compressive strength and fracture mode. • .Impact velocity is an important factor in shock-induced chemical characteristics. • .Each additive has significant effects on energy release behavior

Effect of Lime Addition Methods on Performance Related Properties of Asphalt Concrete Mixture

Directory of Open Access Journals (Sweden)

Amjad Hamd Khalil Albayati

2016-09-01

Full Text Available In the recent years, some of the newly constructed asphalt concrete pavements in Baghdad as well as other cities across Iraq showed premature failures with consequential negative impact on both roadway safety and economy. Frequently, load associated mode of failure (rutting and fatigue as well as, occasionally, moisture damage in some poorly drained sections are the main failure types found in those newly constructed road. In this research, hydrated lime was introduced into asphalt concrete mixtures of wearing course in two methods. The first one was the addition of dry lime on dry aggregate and the second one was the addition of dry lime on saturated surface dry aggregate moisturized by 2.0 to 3.0 percent of water. For each type of addition, five different percentages of lime as a partial replacement of ordinary limestone mineral filler were used; these were; 1.0, 1.5, 2.0, 2.5, and 3 percent by weight of aggregate besides a control mixture that did not contain lime. Marshall Mix design method was used and the performance properties of moisture damage, resilient modulus, permanent deformation and fatigue characteristics were evaluated using indirect tensile strength, uniaxial repeated loading and repeated flexural beam tests. Also, VESYS5W software was implemented to evaluate the pavements performance in terms of rut depth and fatigue area for a typical pavement structure. The main conclusion withdrawn from this research revealed that the use of 2.5 percent hydrated lime in dry addition method and wet addition method showed an improved fatigue and permanent deformation characteristics, lower moisture susceptibility and high resilient modulus.

Copies of editions from V. Vernadsky National Library of Ukraine Old Printed and Rare Editions Department fonds, not mentioned in «Svodnyi catalog knig na inostrannyh yazykah, izdannyh v Rossii v XVIII veke»

Directory of Open Access Journals (Sweden)

Rudakova Y.

2014-01-01

Full Text Available «Svodnyi catalog knig na inostrannyh yazykah, izdannyh v Rossii v XVIII veke (1701-1800» is the first and currently the only bibliographic index of books in foreign languages, printed in Russian Empire typographies in the 18th century. The catalogue was arranged on the basis of fonds of 14 major libraries of former USSR, including the contemporary V. Vernadsky National Library of Ukraine. However, a number of books, not mentioned in the catalogue in question, were found in the fonds of Old Printed and Rare Editions Department of V. Vernadsky National Library of Ukraine. Also a list of editions, which descriptions in the catalogue need to be completed or corrected, was composed. This information will be reflected in the fifth volume of the catalogue that is being prepared for publication in the Library of the Russian Academy of Sciences. The article intends to inform about these additions. They are displayed by two lists. The first list contains numbers of editions, which descriptions in the catalogue are to be improved. The second list contains editions from the fonds of V. Vernadsky National Library of Ukraine Old Printed and Rare Editions Department, which are not mentioned in the catalogue. The lists of additions are supplemented with brief characteristics of the catalogue.

Method for adding additional isotopes to actinide-only burnup credit

International Nuclear Information System (INIS)

Lancaster, D.B.; Fuentes, E.; Kang, C.

1998-01-01

The Topical Report on Actinide-Only Burnup Credit for Pressurized Water Reactor Spent Nuclear Fuel Packages requires computer code validation to be performed against a benchmark set of chemical assays for isotopic concentration and against a benchmark set of critical experiments for package criticality. Both sets contain all the isotopes included in the methodology. The chemical assays used include the uranium and plutonium isotopes, while the critical experiments were composed of UO 2 or MOX rods, covering the isotopes in the actinide only approach. Since other isotopes are not included in the validation benchmark sets, it would be necessary to justify both the content and worth of any additional isotope for which burnup credit is to be taken (i.e., both the concentration and criticality effect of each particular isotope must be validated). A method is proposed here that can be used for any number of additional isotopes. As does the actinide-only burnup credit methodology, this method makes use of chemical assay data to establish the conservatism in the prediction of each isotope's concentration. Criticality validation is also performed using a benchmark set of UO 2 and MOX critical experiments, where the additional isotopes are validated using worth experiments to conservatively account for any uncertainty in their cross sections. The remaining requirements (analysis and modeling parameters, loading criteria generation, and physical implementation and controls) are performed exactly as described in the actinide-only burnup credit methodology. This report provides insight into each particular requirement in the new methodology

Processing simulated high-level liquid waste by heat treatment with addition of TiN and AlN or Al2O3

International Nuclear Information System (INIS)

Uno, Masayoshi; Kinoshita, Hajime; Sakai, Etsuro; Ikeda, Akira; Matsumoto, Y.; Yamanaka, Shinsuke

1999-01-01

The present study aims to decrease the melting temperature of the oxide phase by the addition of the mixture of TiN and AlN or Al 2 O 3 for reduction of the treatment temperature of super high temperature method. The addition of the mixture of TiN and AlN or Al 2 O 3 with the atomic ratio of Al to Ti of 1:9 caused the melting of both the alloy phase and oxide phase at 1673 K. The measured values of density and hardness for thus obtained oxide phase were same as those for the oxide phase obtained at 1873 K without Al. Thus, above mentioned method is achieved at 1673 K without degradation of the properties of the oxide phase as an waste. (author)

Phonetic spelling filter for keyword selection in drug mention mining from social media.

Science.gov (United States)

Pimpalkhute, Pranoti; Patki, Apurv; Nikfarjam, Azadeh; Gonzalez, Graciela

2014-01-01

Social media postings are rich in information that often remain hidden and inaccessible for automatic extraction due to inherent limitations of the site's APIs, which mostly limit access via specific keyword-based searches (and limit both the number of keywords and the number of postings that are returned). When mining social media for drug mentions, one of the first problems to solve is how to derive a list of variants of the drug name (common misspellings) that can capture a sufficient number of postings. We present here an approach that filters the potential variants based on the intuition that, faced with the task of writing an unfamiliar, complex word (the drug name), users will tend to revert to phonetic spelling, and we thus give preference to variants that reflect the phonemes of the correct spelling. The algorithm allowed us to capture 50.4 - 56.0 % of the user comments using only about 18% of the variants.

[Total analysis of organic rubber additives].

Science.gov (United States)

He, Wen-Xuan; Robert, Shanks; You, Ye-Ming

2010-03-01

In the present paper, after middle pressure chromatograph separation using both positive phase and reversed-phase conditions, the organic additives in ethylene-propylene rubber were identified by infrared spectrometer. At the same time, by using solid phase extraction column to maintain the main component-fuel oil in organic additves to avoid its interfering with minor compounds, other organic additves were separated and analysed by GC/Ms. In addition, the remaining active compound such as benzoyl peroxide was identified by CC/Ms, through analyzing acetone extract directly. Using the above mentioned techniques, soften agents (fuel oil, plant oil and phthalte), curing agent (benzoylperoxide), vulcanizing accelerators (2-mercaptobenzothiazole, ethyl thiuram and butyl thiuram), and antiagers (2, 6-Di-tert-butyl-4-methyl phenol and styrenated phenol) in ethylene-propylene rubber were identified. Although the technique was established in ethylene-propylene rubber system, it can be used in other rubber system.

76 FR 5319 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

2011-01-31

... Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline AGENCY: Environmental... gasoline. This proposed rule will provide flexibility to the regulated community by allowing an additional... A. Alternative Test Method for Olefins in Gasoline III. Statutory and Executive Order Reviews A...

76 FR 65382 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

2011-10-21

... Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline AGENCY: Environmental... gasoline. This final rule will provide flexibility to the regulated community by allowing an additional... Method for Olefins in Gasoline III. Statutory and Executive Order Reviews A. Executive Order 12866...

Is R. S. Peters' Way of Mentioning Women in His Texts Detrimental to Philosophy of Education? Some Considerations and Questions

Science.gov (United States)

Lees, Helen E.

2012-01-01

Discussion in this article considers the unfortunate way R.S. Peters made mention of women when it was pertinent to his argumentation: portraying them, directly or indirectly, as abuse-able (murderable), deficient, aberrant, clueless and inconstant. It is argued that the high profile and esteem within which Peter's texts are held within philosophy…

Control of abusive water addition to Octopus vulgaris with non-destructive methods.

Science.gov (United States)

Mendes, Rogério; Schimmer, Ove; Vieira, Helena; Pereira, João; Teixeira, Bárbara

2018-01-01

Abusive water addition to octopus has evidenced the need for quick non-destructive methods for product qualification in the industry and control of fresh commercial products in markets. Electric conductivity (EC)/pH and dielectric property measurements were selected to detect water uptake in octopus. A significant EC decrease was determined after soaking octopus in freshwater for 4 h. EC reflected the water uptake of octopus and the correspondent concentration decrease of available ions in the interstitial fluid. Significant correlations were determined between octopus water uptake, EC (R = -0.940) and moisture/protein (M/P) ratio (R = 0.923) changes. Seasonal and spatial variation in proximate composition did not introduce any uncertainty in EC discrimination of freshwater tampering. Immersion in 5 g L -1 sodium tripolyphosphate (STPP) increased EC to a value similar to control octopus. EC false negatives resulting from the use of additives (STPP and citric acid) were eliminated with the additional determination of pH. Octopus soaked in freshwater, STPP and citric acid can also be clearly discriminated from untreated samples (control) and also from frozen (thawed) ones using the dielectric properties. No significant differences in the dielectric property scores were found between octopus sizes or geographical locations. Simultaneous EC/pH or dielectric property measurements can be used in a handheld device for non-destructive water addition detection in octopus. M/P ratio can be used as a reference destructive method. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

A Review on Synthesis of Nano-TiO2 via Different Methods

Directory of Open Access Journals (Sweden)

M. Malekshahi Byranvand

2013-03-01

Full Text Available Titanium dioxide is one kind of important materials, which has been extensively investigated because of its unique electronic and optical properties. A large number of efforts have been made to synthesize TiO2 materials with different methods. In this review paper, we summarize the synthesis pathways, morphology, as well as crystallization of the nanostructured TiO2. In addition, we also mention several nanostructured TiO2 materials.

Efectivity of Additive Spline for Partial Least Square Method in Regression Model Estimation

Directory of Open Access Journals (Sweden)

Ahmad Bilfarsah

2005-04-01

Full Text Available Additive Spline of Partial Least Square method (ASPL as one generalization of Partial Least Square (PLS method. ASPLS method can be acommodation to non linear and multicollinearity case of predictor variables. As a principle, The ASPLS method approach is cahracterized by two idea. The first is to used parametric transformations of predictors by spline function; the second is to make ASPLS components mutually uncorrelated, to preserve properties of the linear PLS components. The performance of ASPLS compared with other PLS method is illustrated with the fisher economic application especially the tuna fish production.

Syntax mentioned seven times in the CEFR – and how many times at school, in foreign language classrooms?

Directory of Open Access Journals (Sweden)

Darja Mertelj

2014-12-01

Full Text Available In the teaching of foreign languages, complex-clause syntax does not seem to have had an established role over the last 20 years, especially within the communicative approach and, of course, the CEFR. It was previously part of methods which stressed formal approaches to foreign languages and their being taught, but not of natural, acquisition-based methods. With the communicative approach, two important premises were introduced: authentic texts and grammar as a tool when necessary. This is one probable reason why explicit, complex-clause syntax is hardly mentioned in the CEFR, even though it is implicitly present in descriptors, even though it is particularly recognisable in those for writing skills, and even though we know that it can be used for all four skills, as well as to guide learners towards some self-directed learning about language features. To date, in the era of the communicative approach, not much is known about the role of complex-clause syntax in foreign/second language classrooms, in particular from the learners’ viewpoint. In order to bridge this research gap, the paper analyses a questionnaire among learners in secondary schools that looked at their perspectives regarding the (possible role of syntax. The examined aspects consider its role for the four skills, and the benefits of knowing syntax; implicitly, the paper touches on some affective factors and related methodological approaches, along with problems concerning the teaching of syntax. The findings are based on quantitative data; an evaluation of the need for complex-clause syntax is included, and some pedagogical implications are presented.

Establishing optimal methods of detecting wines counterfeited by addition of alcohol

International Nuclear Information System (INIS)

Ranca, Aurora; Menabit, Nelian; Artem, Victoria; Savin, Costica; Vasile, Ancuta; Pasa, Domnica; Postolache, Elena; Iliescu, Maria

2008-01-01

The alcohol is one of the most important parameters characterizing the wine and also, most often a means used to commit forgery. The investigations were made with control wines and wines subject to addition of alcohol of 96% and 50% vol concentration. The wines come from the four wine research stations: SCDVV Murfatlar, SCDVV Iasi, SCDVV Bujoru, and SCDVV Blaj. For checking the addition of alcohol the following methods were used: density measuring, establishing the alcohol / unreduced extract, establishing the glycerol / alcohol ratio and determining the ratios of the isotopic mixtures 18 O/ 16 O, 13 C/ 12 C, D/H. Extensive researches, with high precision equipment are planned to continue in order to exclude any possibility of falsification of wines. (authors)

Important points not mentioned in 'interim report' of nuclear regulation authority

International Nuclear Information System (INIS)

Sato, Satoshi

2014-01-01

The Nuclear Regulation Authority (NRA) published the investigation and examination report on the unexplained issues raised by the National Diet Investigation Commission; 'Analysis of the TEPCO Fukushima Daiichi NPS Accident-Interim Report' in October 2014. The NRA had analyzed seven unexplained issues raised in the National Diet Investigation Commission report, and compiled the results. The author insisted the report should include related views and lessons learned and not just explain investigated and examined phenomena in order to contribute to ensuring nuclear safety in the world. As an example, the author selected the fifth of seven issues; 'operating status of the Isolation Condenser of Unit 1 (IC)'. The report concluded 'the AC-driven valve was closed since the AC power supply kept working even after DC power supply for the IC rupture detection circuit was lost. The isolation valves (2A and 2B) outside the PCV were closed, but isolation valves (1B and 4B) of the IC (system 'B') in the PCV remained open. However, the operating status (open/close) of isolation valves (1A and 4A) of the IC (system 'A') in the PCV is not clear. It is therefore necessary to continue analyses of this issue.' As related important points not mentioned in the report, the author described five points; (1) timing of functional losses of IC system, (2) obsolete aspect of equipment arrangement design (system separation), (3) single failure vulnerability, (4) rolling out issue of IC system to RCIC system (horizontal deployment) and (5) lessons learned from risk-informed 'black swan event'. (T. Tanaka)

Gravimetric and titrimetric methods of analysis

International Nuclear Information System (INIS)

Rives, R.D.; Bruks, R.R.

1983-01-01

Gravimetric and titrimetric methods of analysis are considered. Methods of complexometric titration are mentioned, as well as methods of increasing sensitivity in titrimetry. Gravimetry and titrimetry are applied during analysis for traces of geological materials

H-Point Standard Addition Method for Simultaneous Determination of Eosin and Erytrosine

Directory of Open Access Journals (Sweden)

Amandeep Kaur

2011-01-01

Full Text Available A new, simple, sensitive and selective H-point standard addition method (HPSAM has been developed for resolving binary mixture of food colorants eosin and erythrosine, which show overlapped spectra. The method is based on the complexation of food dyes eosin and erythrosine with Fe(III complexing reagent at pH 5.5 and solubilizing complexes in triton x-100 micellar media. Absorbances at the two pairs of wavelengths, 540 and 550 nm (when eosin acts as analyte or 518 and 542 nm (when erythrosine act as analyte were monitored. This method has satisfactorily been applied for the determination of eosin and erythrosine dyes in synthetic mixtures and commercial products.

Determination of free acid by standard addition method in potassium thiocyanate

International Nuclear Information System (INIS)

Baumann, E.W.

1982-06-01

The free acid content of solutions containing hydrolyzable ions has been determined potentiometrically by a standard addition method. Two increments of acid are added to the sample in 1M potassium thiocyanate solution. The sample concentration is calculated by solution of three simultaneous Nernst equations. The method has been demonstrated for solutions containing Al 3+ , Cr 3+ , Fe 3+ , Hg 2+ , Ni 2+ , Th 4+ , or UO 2 2+ with a metal-to-acid ratio of < 2.5. The method is suitable for determination of 10 μmoles acid in 10 mL total volume. The accuracy can be judged from the agreement of the Nernst slopes found in the presence and absence of hydrolyzable ions. The relative standard deviation is < 2.5%. The report includes a survey of experiments with thermometric, pH, and Gran plot titrations in a variety of complexants, from which the method was evolved. Also included is a literature survey of sixty references, a discussion of the basic measurements, and a complete analytical procedure

Method of recovering oils, etc. , from bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1921-05-23

In the low-temperature distillation of bituminous shales or similar bituminous materials with high ash content for recovery of oil etc., steam or inert gases are introduced from outside through gas taps arranged in a circle in the retort. By the method used steam is introduced simultaneously in levels higher and lower than the one in which the gaseous and vaporized products are removed from the shale material and in such a manner that the zone of oil formation chiefly will be between the two places mentioned where vapors or steam are introduced into the retort. The patent has one additional claim.

Determination of free acid by standard addition method in potassium thiocyanate

International Nuclear Information System (INIS)

1981-01-01

An analytical method for determination of free acidity in all SRP process solutions has been developed. Free acidity was successfully determined in solutions of nitric acid and the nitrates of aluminum, chromium(III), iron(III), mercury(II), nickel(II), thorium, and uranium(VI), at metal-to-acid ratios <2.5. Sample requirements, instrumentation, and mode of operation are similar to those currently used in the Laboratories Department free acid procedures. The simple procedure would be suitable for automation and microprocessor control. The method consists of two additions of known increments of acid into a solution containing the sample aliquot (10 μmoles free acid) and 10 mL 1M potassium thiocyanate. The potential is determined in the initial solution and after each addition with a glass electrode and pH meter. The sample concentration is calculated by solution of three simultaneous Nernst equations. Two programs for this iterative computation are available: one written for the PDP-15 computer and another for a Hewlett-Packard 67 (or 97) programmable calculator. The accuracy of the result is verified by a slope that approximates the theoretical Nernst value. The relative standard deviation is <2.5%. This memorandum includes a survey of experiments with thermometric, pH, and Gran plot titrations in a variety of complexants, from which this particular system and technique logically evolved. The appendix includes a literature survey of sixty references, a discussion of the basic measurements, and a complete analytical procedure. The final step for completion of this RTA is training and consultation at the convenience of the Laboratories Department for demonstration of the method with process samples

Mechanics of additively manufactured biomaterials.

Science.gov (United States)

Zadpoor, Amir A

2017-06-01

Additive manufacturing (3D printing) has found many applications in healthcare including fabrication of biomaterials as well as bioprinting of tissues and organs. Additively manufactured (AM) biomaterials may possess arbitrarily complex micro-architectures that give rise to novel mechanical, physical, and biological properties. The mechanical behavior of such porous biomaterials including their quasi-static mechanical properties and fatigue resistance is not yet well understood. It is particularly important to understand the relationship between the designed micro-architecture (topology) and the resulting mechanical properties. The current special issue is dedicated to understanding the mechanical behavior of AM biomaterials. Although various types of AM biomaterials are represented in the special issue, the primary focus is on AM porous metallic biomaterials. As a prelude to this special issue, this editorial reviews some of the latest findings in the mechanical behavior of AM porous metallic biomaterials so as to describe the current state-of-the-art and set the stage for the other studies appearing in the issue. Some areas that are important for future research are also briefly mentioned. Copyright © 2017 Elsevier Ltd. All rights reserved.

Routes to chaos in continuous mechanical systems. Part 1: Mathematical models and solution methods

International Nuclear Information System (INIS)

Awrejcewicz, J.; Krysko, V.A.; Papkova, I.V.; Krysko, A.V.

2012-01-01

In this work chaotic dynamics of continuous mechanical systems such as flexible plates and shallow shells is studied. Namely, a wide class of the mentioned objects is analyzed including flexible plates and cylinder-like panels of infinite length, rectangular spherical and cylindrical shells, closed cylindrical shells, axially symmetric plates, as well as spherical and conical shells. The considered problems are solved by the Bubnov–Galerkin and higher approximation Ritz methods. Convergence and validation of those methods are studied. The Cauchy problems are solved mainly by the fourth Runge-Kutta method, although all variants of the Runge-Kutta methods are considered. New scenarios of transition from regular to chaotic orbits are detected, analyzed and discussed. First part of the paper is devoted to the validation of results obtained. This is why the same infinite length problem is reduced to that of a finite dimension through the FDM (Finite Difference Method) with the approximation order of O(c 2 ), BGM (Bubnov–Galerkin Method) or RM (Ritz Method) with higher approximations. We pay attention not only to convergence of the mentioned methods regarding the number of partitions of the interval [0, 1] in the FDM or regarding the number of terms in the series applied either in the BGM or RM methods, but we also compare the results obtained via the mentioned different approaches. Furthermore, a so called practical convergence of different Runge-Kutta type methods are tested starting from the second and ending with the eighth order. Second part of the work is devoted to a study of routes to chaos in the so far mentioned mechanical objects. For this purpose the so-called “dynamical charts” are constructed versus control parameters {q 0 , ω p }, where q 0 denotes the loading amplitude, and ω p is the loading frequency. The charts are constructed through analyses of frequency power spectra and the largest Lyapunov exponent (LE). Analysis of the mentioned charts

Importance of perceived naturalness for acceptance of food additives and cultured meat.

Science.gov (United States)

Siegrist, Michael; Sütterlin, Bernadette

2017-06-01

Four experiments examined some factors influencing the perceived naturalness of food products and their biasing effect on risk perception. The results of Experiment 1a showed that three food additives displaying their respective E-numbers (i.e., codes for food additives in the European Union and Switzerland) decreased perceived naturalness. Experiment 1b demonstrated that mentioning possible health effects decreased the perceived naturalness of a plant-based food additive. This experiment further showed that it would not matter for perceived naturalness whether the food was synthetic or nature-identical. Moreover, the results of Experiments 2 and 3 suggested that the same risk associated with meat consumption was much more acceptable for traditionally produced meat compared with in-vitro meat. Experiment 3 further indicated that the perceived naturalness of the meat (i.e., traditional or cultured meat) had a full mediation effect on participants' evaluation of the acceptability of the risk of colon cancer associated with the meat consumption. Even if the new production method (i.e., cultured meat) was more environmentally friendly and less harmful to animals, the perceived lack of naturalness might reduce the acceptability of the risk associated with such a product. The present study provides evidence that consumers rely on symbolic information when evaluating foods, which may lead to biased judgments and decisions. Copyright © 2017 Elsevier Ltd. All rights reserved.

GIDA KATKI MADDELERİ VE İNSAN SAĞLIĞI ÜZERİNE ETKİLERİ : FOOD ADDITIVES AND EFFECTS ON THE HUMAN HEALTH

OpenAIRE

ERFDEN ÇALIŞIR, Zeynep; ÇALIŞKAN, Deniz

2003-01-01

This review is going to be an evaluation food additives in ready-to-eat foods, which are a part of our lives. With increasing consumption of ready-to-eat-foods a lot of research has been going into the matter of increased exposure to additives. Addiüonally, it will mention the effect of food additives on the systems on the human body

Net Analyte Signal Standard Additions Method for Simultaneous Determination of Sulfamethoxazole and Trimethoprim in Pharmaceutical Formulations and Biological Fluids

Directory of Open Access Journals (Sweden)

M. H. Givianrad

2012-01-01

Full Text Available The applicability of a novel net analyte signal standard addition method (NASSAM to the resolving of overlapping spectra corresponding to the sulfamethoxazole and trimethoprim was verified by UV-visible spectrophotometry. The results confirmed that the net analyte signal standard additions method with simultaneous addition of both analytes is suitable for the simultaneous determination of sulfamethoxazole and trimethoprim in aqueous media. Moreover, applying the net analyte signal standard additions method revealed that the two drugs could be determined simultaneously with the concentration ratios of sulfamethoxazole to trimethoprim varying from 1:35 to 60:1 in the mixed samples. In addition, the limits of detections were 0.26 and 0.23 μmol L-1 for sulfamethoxazole and trimethoprim, respectively. The proposed method has been effectively applied to the simultaneous determination of sulfamethoxazole and trimethoprim in some synthetic, pharmaceutical formulation and biological fluid samples.

Evaluation of polymer micro parts produced by additive manufacturing processes using vat photopolymerization method

DEFF Research Database (Denmark)

Davoudinejad, Ali; Pedersen, David Bue; Tosello, Guido

2017-01-01

Micro manufacturing scale feature production by Additive Manufacturing (AM) processes for the direct production of miniaturized polymer components is analysed in this work. The study characterizes the AM processes for polymer micro parts productions using the vat photopolymerization method...

Development of the H-point standard additions method for coupled liquid-chromatography and UV-visible spectrophotometry

Energy Technology Data Exchange (ETDEWEB)

Campins-Falco, Pilar; Bosch-Reig, Francisco; Herraez-Hernandez, Rosa; Sevillano-Cabeza, Adela (Universidad de Valencia (Spain). Facultad de Quimica, Departamento de Quimica Analitica)

1992-02-10

This work establishes the fundamentals of the H-point standard additions method for liquid chromatography for the simultaneous analysis of binary mixtures with overlapped chromatographic peaks. The method was compared with the deconvolution method of peak suppression and the second derivative of elution profiles. Different mixtures of diuretics were satisfactorily resolved. (author). 21 refs.; 9 figs.; 2 tabs.

Geometrical shape assessment of additively manufactured features by direct light processing vat polymerization method

DEFF Research Database (Denmark)

Péreza, Lucia C. Díaz; Davoudinejad, Ali; Quagliotti, Danilo

The importance of Additive Manufacturing (AM) in the field of micro manufacturing is increasing. Vat Polymerization Methods are one of the lead AM technologies to produce polymer micro parts. In the Technical University of Denmark (DTU), a vat photopolymerization AM machine able to print features...

Generalized concentration addition: a method for examining mixtures containing partial agonists.

Science.gov (United States)

Howard, Gregory J; Webster, Thomas F

2009-08-07

Environmentally relevant toxic exposures often consist of simultaneous exposure to multiple agents. Methods to predict the expected outcome of such combinations are critical both to risk assessment and to an accurate judgment of whether combinations are synergistic or antagonistic. Concentration addition (CA) has commonly been used to assess the presence of synergy or antagonism in combinations of similarly acting chemicals, and to predict effects of combinations of such agents. CA has the advantage of clear graphical interpretation: Curves of constant joint effect (isoboles) must be negatively sloped straight lines if the mixture is concentration additive. However, CA cannot be directly used to assess combinations that include partial agonists, although such agents are of considerable interest. Here, we propose a natural extension of CA to a functional form that may be applied to mixtures including full agonists and partial agonists. This extended definition, for which we suggest the term "generalized concentration addition," encompasses linear isoboles with slopes of any sign. We apply this approach to the simple example of agents with dose-response relationships described by Hill functions with slope parameter n=1. The resulting isoboles are in all cases linear, with negative, zero and positive slopes. Using simple mechanistic models of ligand-receptor systems, we show that the same isobole pattern and joint effects are generated by modeled combinations of full and partial agonists. Special cases include combinations of two full agonists and a full agonist plus a competitive antagonist.

Net Analyte Signal Standard Additions Method for Simultaneous Determination of Sulfamethoxazole and Trimethoprim in Pharmaceutical Formulations and Biological Fluids

OpenAIRE

Givianrad, M. H.; Mohagheghian, M.

2012-01-01

The applicability of a novel net analyte signal standard addition method (NASSAM) to the resolving of overlapping spectra corresponding to the sulfamethoxazole and trimethoprim was verified by UV-visible spectrophotometry. The results confirmed that the net analyte signal standard additions method with simultaneous addition of both analytes is suitable for the simultaneous determination of sulfamethoxazole and trimethoprim in aqueous media. Moreover, applying the net analyte signal standard a...

Groundwater Seepage Estimation into Amirkabir Tunnel Using Analytical Methods and DEM and SGR Method

OpenAIRE

Hadi Farhadian; Homayoon Katibeh

2015-01-01

In this paper, groundwater seepage into Amirkabir tunnel has been estimated using analytical and numerical methods for 14 different sections of the tunnel. Site Groundwater Rating (SGR) method also has been performed for qualitative and quantitative classification of the tunnel sections. The obtained results of above mentioned methods were compared together. The study shows reasonable accordance with results of the all methods unless for two sections of tunnel. In these t...

Photon and proton activation analysis of iron and steel standards using the internal standard method coupled with the standard addition method

International Nuclear Information System (INIS)

Masumoto, K.; Hara, M.; Hasegawa, D.; Iino, E.; Yagi, M.

1997-01-01

The internal standard method coupled with the standard addition method has been applied to photon activation analysis and proton activation analysis of minor elements and trace impurities in various types of iron and steel samples issued by the Iron and Steel Institute of Japan (ISIJ). Samples and standard addition samples were once dissolved to mix homogeneously, an internal standard and elements to be determined and solidified as a silica-gel to make a similar matrix composition and geometry. Cerium and yttrium were used as an internal standard in photon and proton activation, respectively. In photon activation, 20 MeV electron beam was used for bremsstrahlung irradiation to reduce matrix activity and nuclear interference reactions, and the results were compared with those of 30 MeV irradiation. In proton activation, iron was removed by the MIBK extraction method after dissolving samples to reduce the radioactivity of 56 Co from iron via 56 Fe(p, n) 56 Co reaction. The results of proton and photon activation analysis were in good agreement with the standard values of ISIJ. (author)

Ruminal Methane Production on Simple Phenolic Acids Addition in in Vitro Gas Production Method

Directory of Open Access Journals (Sweden)

A. Jayanegara

2009-04-01

Full Text Available Methane production from ruminants contributes to total global methane production, which is an important contributor to global warming. In this experiment, six sources of simple phenolic acids (benzoic, cinnamic, phenylacetic, caffeic, p-coumaric and ferulic acids at two different levels (2 and 5 mM added to hay diet were evaluated for their potential to reduce enteric methane production using in vitro Hohenheim gas production method. The measured variables were gas production, methane, organic matter digestibility (OMD, and short chain fatty acids (SCFA. The results showed that addition of cinnamic, caffeic, p-coumaric and ferulic acids at 5 mM significantly (P p-coumaric > ferulic > cinnamic. The addition of simple phenols did not significantly decrease OMD. Addition of simple phenols tends to decrease total SCFA production. It was concluded that methane decrease by addition of phenolic acids was relatively small, and the effect of phenolic acids on methane decrease depended on the source and concentration applied.

Effect of the chlortetracycline addition method on methane production from the anaerobic digestion of swine wastewater.

Science.gov (United States)

Huang, Lu; Wen, Xin; Wang, Yan; Zou, Yongde; Ma, Baohua; Liao, Xindi; Liang, Juanboo; Wu, Yinbao

2014-10-01

Effects of antibiotic residues on methane production in anaerobic digestion are commonly studied using the following two antibiotic addition methods: (1) adding manure from animals that consume a diet containing antibiotics, and (2) adding antibiotic-free animal manure spiked with antibiotics. This study used chlortetracycline (CTC) as a model antibiotic to examine the effects of the antibiotic addition method on methane production in anaerobic digestion under two different swine wastewater concentrations (0.55 and 0.22mg CTC/g dry manure). The results showed that CTC degradation rate in which manure was directly added at 0.55mg CTC/g (HSPIKE treatment) was lower than the control values and the rest of the treatment groups. Methane production from the HSPIKE treatment was reduced (pdigesters, and the total nitrogen of the 0.55mg CTC/kg manure collected from mediated swine was significantly higher than the other values. Therefore, different methane production under different antibiotic addition methods might be explained by the microbial activity and the concentrations of antibiotic intermediate products and metabolites. Because the primary entry route of veterinary antibiotics into an anaerobic digester is by contaminated animal manure, the most appropriate method for studying antibiotic residue effects on methane production may be using manure from animals that are given a particular antibiotic, rather than adding the antibiotic directly to the anaerobic digester. Copyright © 2014. Published by Elsevier B.V.

The method of manufacture of nylon dental partially removable prosthesis using additive technologies

Science.gov (United States)

Kashapov, R. N.; Korobkina, A. I.; Platonov, E. V.; Saleeva, G. T.

2014-12-01

The article is devoted to the topic of creating new methods of dental prosthesis. The aim of this work is to investigate the possibility of using additive technology to create nylon prosthesis. As a result of experimental studies, was made a sample of nylon partially removable prosthesis using 3D printing has allowed to simplify, accelerate and reduce the coat of manufacturing high-precision nylon dentures.

Evaluation method of radiation stability of hardened cement paste with chemical additives

Energy Technology Data Exchange (ETDEWEB)

Medvedev, Vyacheslav; Pustovgar, Andrey [National Research Univ. ' Moscow State Univ. of Civil Engineering' (MSUCE), Moscow (Russian Federation); National Research Univ. ' Moscow State Univ. of Civil Engineering' (MSUCE), Moscow (Russian Federation). Scientific Research Inst. of Constructional Materials and Technologies; Denisov, Alexander; Soloviev, Vitaly [National Research Univ. ' Moscow State Univ. of Civil Engineering' (MSUCE), Moscow (Russian Federation)

2013-07-01

The influence of additives on the radiation resistance of the concrete will occur through the influence of radiation changes of hardened cement paste on radiation changes of concrete and can be quite significant. The test sequence was produced according to the modified method. The samples were prepared in the form of prisms with the following dimensions: 10 mm x 10 mm, 30 mm long. Measurement series were produced after each heating and cooling sequence. Then the difference between the values before and after heating was calculated. (orig.)

Finite element method - theory and applications

International Nuclear Information System (INIS)

Baset, S.

1992-01-01

This paper summarizes the mathematical basis of the finite element method. Attention is drawn to the natural development of the method from an engineering analysis tool into a general numerical analysis tool. A particular application to the stress analysis of rubber materials is presented. Special advantages and issues associated with the method are mentioned. (author). 4 refs., 3 figs

The regression-calibration method for fitting generalized linear models with additive measurement error

OpenAIRE

James W. Hardin; Henrik Schmeidiche; Raymond J. Carroll

2003-01-01

This paper discusses and illustrates the method of regression calibration. This is a straightforward technique for fitting models with additive measurement error. We present this discussion in terms of generalized linear models (GLMs) following the notation defined in Hardin and Carroll (2003). Discussion will include specified measurement error, measurement error estimated by replicate error-prone proxies, and measurement error estimated by instrumental variables. The discussion focuses on s...

Monitoring system for the quality assessment in additive manufacturing

Energy Technology Data Exchange (ETDEWEB)

Carl, Volker, E-mail: carl@t-zfp.de [Carl Messtechnik, Thyssenstrasse 183a, 46535 Dinslaken (Germany)

2015-03-31

Additive Manufacturing (AM) refers to a process by which a set of digital data -representing a certain complex 3dim design - is used to grow the respective 3dim real structure equal to the corresponding design. For the powder-based EOS manufacturing process a variety of plastic and metal materials can be used. Thereby, AM is in many aspects a very powerful tool as it can help to overcome particular limitations in conventional manufacturing. AM enables more freedom of design, complex, hollow and/or lightweight structures as well as product individualisation and functional integration. As such it is a promising approach with respect to the future design and manufacturing of complex 3dim structures. On the other hand, it certainly calls for new methods and standards in view of quality assessment. In particular, when utilizing AM for the design of complex parts used in aviation and aerospace technologies, appropriate monitoring systems are mandatory. In this respect, recently, sustainable progress has been accomplished by joining the common efforts and concerns of a manufacturer Additive Manufacturing systems and respective materials (EOS), along with those of an operator of such systems (MTU Aero Engines) and experienced application engineers (Carl Metrology), using decent know how in the field of optical and infrared methods regarding non-destructive-examination (NDE). The newly developed technology is best described by a high-resolution layer by layer inspection technique, which allows for a 3D tomography-analysis of the complex part at any time during the manufacturing process. Thereby, inspection costs are kept rather low by using smart image-processing methods as well as CMOS sensors instead of infrared detectors. Moreover, results from conventional physical metallurgy may easily be correlated with the predictive results of the monitoring system which not only allows for improvements of the AM monitoring system, but finally leads to an optimisation of the quality

Laser and Electron Beam Additive Manufacturing Methods of Fabricating Titanium Bone Implants

Directory of Open Access Journals (Sweden)

Bartłomiej Wysocki

2017-06-01

Full Text Available Additive Manufacturing (AM methods are generally used to produce an early sample or near net-shape elements based on three-dimensional geometrical modules. To date, publications on AM of metal implants have mainly focused on knee and hip replacements or bone scaffolds for tissue engineering. The direct fabrication of metallic implants can be achieved by methods, such as Selective Laser Melting (SLM or Electron Beam Melting (EBM. This work compares the SLM and EBM methods used in the fabrication of titanium bone implants by analyzing the microstructure, mechanical properties and cytotoxicity. The SLM process was conducted in an environmental chamber using 0.4–0.6 vol % of oxygen to enhance the mechanical properties of a Ti-6Al-4V alloy. SLM processed material had high anisotropy of mechanical properties and superior UTS (1246–1421 MPa when compared to the EBM (972–976 MPa and the wrought material (933–942 MPa. The microstructure and phase composition depended on the used fabrication method. The AM methods caused the formation of long epitaxial grains of the prior β phase. The equilibrium phases (α + β and non-equilibrium α’ martensite was obtained after EBM and SLM, respectively. Although it was found that the heat transfer that occurs during the layer by layer generation of the component caused aluminum content deviations, neither methods generated any cytotoxic effects. Furthermore, in contrast to SLM, the EBM fabricated material met the ASTMF136 standard for surgical implant applications.

DIAGNOSTIC METHODS IN BREAST CANCER DETECTION

Directory of Open Access Journals (Sweden)

Kristijana Hertl

2018-02-01

Full Text Available Background. In the world as well as in Slovenia, breast cancer is the most frequent female cancer. Due to its high incidence, it appears to be a serious health and economic problem. Content. Among other, tumour size at diagnosis, is an important prognostic factors of the course of the disease. The probability of axillary lymph node involvement as well as distant metastases is greater in larger tumours. This is the reason that encouraged the development of various diagnostic methods for early detection of small, clinically non-palpable breast tumours. Mammography, however, remains the »golden standard« of early breast cancer detection. It is the basic diagnostic method applied in all symptomatic women over 35 years of age and in asymptomatic women over 40 years of age. Ultrasonography (US, additional projections, magnetic resonance imaging (MRI and ductography are regarded as complementary diagnostic breast imaging techniques in addition to mammography. The detected changes in the breast can be further confirmed by US-, MR-guided or stereotactic biopsy. If necessary, surgical biopsy and the excision of a tissue sample, after wire or isotope localisation of the nonpalpable lesion, can be performed. Conclusions. Any of the above mentioned diagnostic methods has advantages as well as drawbacks and only detailed knowledge and understanding of each of them may assure the best option.

Routing Corners of Building Structures - by the Method of Vector Addition - Measured with RTN GNSS Surveying Technology

Science.gov (United States)

Krzyżek, Robert

2015-12-01

The paper deals with the problem of surveying buildings in the RTN GNSS mode using modernized indirect methods of measurement. As a result of the classical realtime measurements using indirect methods (intersection of straight lines or a point on a straight line), we obtain a building structure (a building) which is largely deformed. This distortion is due to the inconsistency of the actual dimensions of the building (tie distances) relative to the obtained measurement results. In order to eliminate these discrepancies, and thus to ensure full consistency of the building geometric structure, an innovative solution was applied - the method of vector addition - to modify the linear values (tie distances) of the external face of the building walls. A separate research problem tackled in the article, although not yet fully solved, is the issue of coordinates of corners of a building obtained after the application of the method of vector addition.

Classical Measurement Methods and Laser Scanning Usage in Shaft Hoist Assembly Inventory

Science.gov (United States)

Jaśkowski, Wojciech; Lipecki, Tomasz; Matwij, Wojciech; Jabłoński, Mateusz

2018-03-01

The shaft hoist assembly is the base of underground mining plant. Its efficiency and correct operation is subject to restrictive legal regulations and is controlled on a daily visual assessment by shaft crew and energomechanics. In addition, in the regular interval, the shaft hoist assembly is subject to a thorough inventory, which includes the determination of the geometrical relationships between the hoisting machine, the headframe and the shaft with its housing. Inventory measurements for shaft and headframe are used for years of conventional geodetic methods including mechanical or laser plumbing and tachymetric surveys. Additional precision levelling is also used for measuring shafts of hoisting machines and rope pulleys. Continuous modernization of measuring technology makes it possible to implement the further methods to the above mentioned purposes. The comparison of the accuracy and the economics of performing measurements based on many years of experience with comprehensive inventory of shaft hoist assembly using various research techniques was made and detailed in the article.

Classical Measurement Methods and Laser Scanning Usage in Shaft Hoist Assembly Inventory

Directory of Open Access Journals (Sweden)

Jaśkowski Wojciech

2018-01-01

Full Text Available The shaft hoist assembly is the base of underground mining plant. Its efficiency and correct operation is subject to restrictive legal regulations and is controlled on a daily visual assessment by shaft crew and energomechanics. In addition, in the regular interval, the shaft hoist assembly is subject to a thorough inventory, which includes the determination of the geometrical relationships between the hoisting machine, the headframe and the shaft with its housing. Inventory measurements for shaft and headframe are used for years of conventional geodetic methods including mechanical or laser plumbing and tachymetric surveys. Additional precision levelling is also used for measuring shafts of hoisting machines and rope pulleys. Continuous modernization of measuring technology makes it possible to implement the further methods to the above mentioned purposes. The comparison of the accuracy and the economics of performing measurements based on many years of experience with comprehensive inventory of shaft hoist assembly using various research techniques was made and detailed in the article.

Method of dissolving metal ruthenium

International Nuclear Information System (INIS)

Tsuno, Masao; Soda, Yasuhiko; Kuroda, Sadaomi; Koga, Tadaaki.

1988-01-01

Purpose: To dissolve and clean metal ruthenium deposited to the inner surface of a dissolving vessel for spent fuel rods. Method: Metal ruthenium is dissolved in a solution of an alkali metal hydroxide to which potassium permanganate is added. As the alkali metal hydroxide used herein there can be mentioned potassium hydroxide, sodium hydroxide and lithium hydroxide can be mentioned, which is used as an aqueous solution from 5 to 20 % concentration in view of the solubility of metal ruthenium and economical merit. Further, potassium permanganate is used by adding to the solution of alkali metal hydroxide at a concentration of 1 to 5 %. (Yoshihara, H.)

Investigation of possible causes of the additional torque on the yacht's rudder

Science.gov (United States)

Lubomir, Soukup; Jaroslav, Stigler; Abdellah, Kharicha

2016-03-01

The present article deals with investigation of possible causes of the additional torque on the yacht's rudder. One of the most important aspect for design of yachts are the symmetric conditions of all parts, which are located under water level and concentricity of the ship's screw, rudder and keel relative to the hull. These symmetric and concentricity conditions have a major impact on the resulting dynamic properties of the ships. They have either substantial impact on the overall efficiency of installed engine and ship's screw. As the result of poorly designed above mentioned parts, there can be an unsolicited additional torque on the yacht's rudder and higher consumption of the fuel. Last but not least of these problems leads to poor controllability and discomfort within steering. This article is focused on the investigation of possible causes of the additional torque on the yacht's rudder.

The Capacity Profile: a method to classify additional care needs in children with neurodevelopmental disabilities

NARCIS (Netherlands)

Meester-Delver, Anke; Beelen, Anita; Hennekam, Raoul; Nollet, Frans; Hadders-Algra, Mijna

2007-01-01

The aim of this study was to determine the interrater reliability and stability over time of the Capacity Profile (CAP). The CAP is a standardized method for classifying additional care needs indicated by current impairments in five domains of body functions: physical health, neuromusculoskeletal

[Doppler echocardiography of tricuspid insufficiency. Methods of quantification].

Science.gov (United States)

Loubeyre, C; Tribouilloy, C; Adam, M C; Mirode, A; Trojette, F; Lesbre, J P

1994-01-01

Evaluation of tricuspid incompetence has benefitted considerably from the development of Doppler ultrasound. In addition to direct analysis of the valves, which provides information about the mechanism involved, this method is able to provide an accurate evaluation, mainly through use of the Doppler mode. In addition to new criteria being evaluated (mainly the convergence zone of the regurgitant jet), some indices are recognised as good quantitative parameters: extension of the regurgitant jet into the right atrium, anterograde tricuspid flow, laminar nature of the regurgitant flow, analysis of the flow in the supra-hepatic veins, this is only semi-quantitative, since the calculation of the regurgitation fraction from the pulsed Doppler does not seem to be reliable; This accurate semi-quantitative evaluation is made possible by careful and consistent use of all the criteria available. The authors set out to discuss the value of the various evaluation criteria mentioned in the literature and try to define a practical approach.

Calculation of Five Thermodynamic Molecular Descriptors by Means of a General Computer Algorithm Based on the Group-Additivity Method: Standard Enthalpies of Vaporization, Sublimation and Solvation, and Entropy of Fusion of Ordinary Organic Molecules and Total Phase-Change Entropy of Liquid Crystals

Directory of Open Access Journals (Sweden)

Rudolf Naef

2017-06-01

Full Text Available The calculation of the standard enthalpies of vaporization, sublimation and solvation of organic molecules is presented using a common computer algorithm on the basis of a group-additivity method. The same algorithm is also shown to enable the calculation of their entropy of fusion as well as the total phase-change entropy of liquid crystals. The present method is based on the complete breakdown of the molecules into their constituting atoms and their immediate neighbourhood; the respective calculations of the contribution of the atomic groups by means of the Gauss-Seidel fitting method is based on experimental data collected from literature. The feasibility of the calculations for each of the mentioned descriptors was verified by means of a 10-fold cross-validation procedure proving the good to high quality of the predicted values for the three mentioned enthalpies and for the entropy of fusion, whereas the predictive quality for the total phase-change entropy of liquid crystals was poor. The goodness of fit (Q2 and the standard deviation (σ of the cross-validation calculations for the five descriptors was as follows: 0.9641 and 4.56 kJ/mol (N = 3386 test molecules for the enthalpy of vaporization, 0.8657 and 11.39 kJ/mol (N = 1791 for the enthalpy of sublimation, 0.9546 and 4.34 kJ/mol (N = 373 for the enthalpy of solvation, 0.8727 and 17.93 J/mol/K (N = 2637 for the entropy of fusion and 0.5804 and 32.79 J/mol/K (N = 2643 for the total phase-change entropy of liquid crystals. The large discrepancy between the results of the two closely related entropies is discussed in detail. Molecules for which both the standard enthalpies of vaporization and sublimation were calculable, enabled the estimation of their standard enthalpy of fusion by simple subtraction of the former from the latter enthalpy. For 990 of them the experimental enthalpy-of-fusion values are also known, allowing their comparison with predictions, yielding a correlation

Calculation of Five Thermodynamic Molecular Descriptors by Means of a General Computer Algorithm Based on the Group-Additivity Method: Standard Enthalpies of Vaporization, Sublimation and Solvation, and Entropy of Fusion of Ordinary Organic Molecules and Total Phase-Change Entropy of Liquid Crystals.

Science.gov (United States)

Naef, Rudolf; Acree, William E

2017-06-25

The calculation of the standard enthalpies of vaporization, sublimation and solvation of organic molecules is presented using a common computer algorithm on the basis of a group-additivity method. The same algorithm is also shown to enable the calculation of their entropy of fusion as well as the total phase-change entropy of liquid crystals. The present method is based on the complete breakdown of the molecules into their constituting atoms and their immediate neighbourhood; the respective calculations of the contribution of the atomic groups by means of the Gauss-Seidel fitting method is based on experimental data collected from literature. The feasibility of the calculations for each of the mentioned descriptors was verified by means of a 10-fold cross-validation procedure proving the good to high quality of the predicted values for the three mentioned enthalpies and for the entropy of fusion, whereas the predictive quality for the total phase-change entropy of liquid crystals was poor. The goodness of fit ( Q ²) and the standard deviation (σ) of the cross-validation calculations for the five descriptors was as follows: 0.9641 and 4.56 kJ/mol ( N = 3386 test molecules) for the enthalpy of vaporization, 0.8657 and 11.39 kJ/mol ( N = 1791) for the enthalpy of sublimation, 0.9546 and 4.34 kJ/mol ( N = 373) for the enthalpy of solvation, 0.8727 and 17.93 J/mol/K ( N = 2637) for the entropy of fusion and 0.5804 and 32.79 J/mol/K ( N = 2643) for the total phase-change entropy of liquid crystals. The large discrepancy between the results of the two closely related entropies is discussed in detail. Molecules for which both the standard enthalpies of vaporization and sublimation were calculable, enabled the estimation of their standard enthalpy of fusion by simple subtraction of the former from the latter enthalpy. For 990 of them the experimental enthalpy-of-fusion values are also known, allowing their comparison with predictions, yielding a correlation coefficient R

Fully implicit two-phase reservoir simulation with the additive schwarz preconditioned inexact newton method

KAUST Repository

Liu, Lulu

2013-01-01

The fully implicit approach is attractive in reservoir simulation for reasons of numerical stability and the avoidance of splitting errors when solving multiphase flow problems, but a large nonlinear system must be solved at each time step, so efficient and robust numerical methods are required to treat the nonlinearity. The Additive Schwarz Preconditioned Inexact Newton (ASPIN) framework, as an option for the outermost solver, successfully handles strong nonlinearities in computational fluid dynamics, but is barely explored for the highly nonlinear models of complex multiphase flow with capillarity, heterogeneity, and complex geometry. In this paper, the fully implicit ASPIN method is demonstrated for a finite volume discretization based on incompressible two-phase reservoir simulators in the presence of capillary forces and gravity. Numerical experiments show that the number of global nonlinear iterations is not only scalable with respect to the number of processors, but also significantly reduced compared with the standard inexact Newton method with a backtracking technique. Moreover, the ASPIN method, in contrast with the IMPES method, saves overall execution time because of the savings in timestep size.

tagtog: interactive and text-mining-assisted annotation of gene mentions in PLOS full-text articles.

Science.gov (United States)

Cejuela, Juan Miguel; McQuilton, Peter; Ponting, Laura; Marygold, Steven J; Stefancsik, Raymund; Millburn, Gillian H; Rost, Burkhard

2014-01-01

The breadth and depth of biomedical literature are increasing year upon year. To keep abreast of these increases, FlyBase, a database for Drosophila genomic and genetic information, is constantly exploring new ways to mine the published literature to increase the efficiency and accuracy of manual curation and to automate some aspects, such as triaging and entity extraction. Toward this end, we present the 'tagtog' system, a web-based annotation framework that can be used to mark up biological entities (such as genes) and concepts (such as Gene Ontology terms) in full-text articles. tagtog leverages manual user annotation in combination with automatic machine-learned annotation to provide accurate identification of gene symbols and gene names. As part of the BioCreative IV Interactive Annotation Task, FlyBase has used tagtog to identify and extract mentions of Drosophila melanogaster gene symbols and names in full-text biomedical articles from the PLOS stable of journals. We show here the results of three experiments with different sized corpora and assess gene recognition performance and curation speed. We conclude that tagtog-named entity recognition improves with a larger corpus and that tagtog-assisted curation is quicker than manual curation. DATABASE URL: www.tagtog.net, www.flybase.org.

An Approximate Proximal Bundle Method to Minimize a Class of Maximum Eigenvalue Functions

Directory of Open Access Journals (Sweden)

Wei Wang

2014-01-01

Full Text Available We present an approximate nonsmooth algorithm to solve a minimization problem, in which the objective function is the sum of a maximum eigenvalue function of matrices and a convex function. The essential idea to solve the optimization problem in this paper is similar to the thought of proximal bundle method, but the difference is that we choose approximate subgradient and function value to construct approximate cutting-plane model to solve the above mentioned problem. An important advantage of the approximate cutting-plane model for objective function is that it is more stable than cutting-plane model. In addition, the approximate proximal bundle method algorithm can be given. Furthermore, the sequences generated by the algorithm converge to the optimal solution of the original problem.

The methods of receiving coal water suspension and its use as the modifying additive in concrete

Science.gov (United States)

Buyantuyev, S. L.; Urkhanova, L. A.; Lkhasaranov, S. A.; Stebenkova, Y. Y.; Khmelev, A. B.; Kondratenko, A. S.

2017-01-01

Results of research of the coal water suspension (CWS) from a cake received in the electrodigit ways in the fluid environment and gas are given in article and also the possibilities of its use as the modifying additive in concrete are considered. Use of a coal cake is perspective as it is a withdrawal of the coal and concentrating enterprises and has extremely low cost. Methods of receiving CWS and possibility of formation of carbon nanomaterials (CNM) are given in their structure. Research and the analysis of a microstructure of a surface of exemplars before electrodigit processing, their element structure, dependence of durability of a cement stone on a look and quantity of an additive of CWS is conducted. For modification of cement the carbon nanomaterials received from the following exemplars of water coal suspensions were used: foams from a cake from a scrubber of the plasma modular reactor, coal water suspension from a cake from electrodigit installation. The product which can find further application for a power engineering as fuel for combustion, and also in structural materials science, in particular, as the modifying additive in concrete allows to receive these methods.

Deposition of additives onto surface of carbon materials by blending method--general conception

International Nuclear Information System (INIS)

Przepiorski, Jacek

2005-01-01

Carbon fibers loaded with potassium carbonate and with metallic copper were prepared by applying a blending method. Raw isotropic coal pitch was blended with KOH or CuBr 2 and obtained mixtures were subjected to spinning. In this way KOH and copper salt-blended fiber with uniform distribution of potassium and copper were spun. The raw fibers were exposed to stabilization with a mixture of CO 2 and air or air only through heating to 330 deg. C and next to treatment with carbon dioxide or hydrogen at higher temperatures. Electron probe micro-analysis (EPMA) analyses showed presence of potassium carbonate or metallic copper predominantly in peripheral regions of the obtained fibers. Basing on the mechanisms of potassium and copper diffusion over the carbon volume, generalized method for the deposition of additives onto surface of carbon materials is proposed

Advanced Methods for Direct Ink Write Additive Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Compel, W. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lewicki, J. P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2018-01-24

Lawrence Livermore National Laboratory is one of the world’s premier labs for research and development of additive manufacturing processes. Out of these many processes, direct ink write (DIW) is arguably one of the most relevant for the manufacture of architected polymeric materials, components and hardware. However, a bottleneck in this pipeline that has largely been ignored to date is the lack of advanced software implementation with respect to toolpath execution. There remains to be a convenient, automated method to design and produce complex parts that is user-friendly and enabling for the realization of next generation designs and structures. For a material to be suitable as a DIW ink it must possess the appropriate rheological properties for this process. Most importantly, the material must exhibit shear-thinning in order to extrude through a print head and have a rapid recovery of its static shear modulus. This makes it possible for the extrudate to be self-supporting upon exiting the print head. While this and other prerequisites narrow the scope of ‘offthe- shelf’ printable materials directly amenable to DIW, the process still tolerates a wide range of potential feedstock materials. These include metallic alloys, inorganic solvent borne dispersions, polymeric melts, filler stabilized monomer compositions, pre-elastomeric feedstocks and thermoset resins each of which requires custom print conditions tailored to the individual ink. As such, an ink perfectly suited for DIW may be prematurely determined to be undesirable for the process if printed under the wrong conditions. Defining appropriate print conditions such as extrusion rate, layer height, and maximum bridge length is a vital first step in validating an ink’s DIW capability.

Methods of equipment conservation of a carboelectric

International Nuclear Information System (INIS)

Hurtado Higuera, Julio Cesar

2001-01-01

Several conservation methods are mentioned like they are those of conservation in dry, in humid, conservation of bombs of water conservation, of turbines, of generators, of transformers, of electric motors and conservation of coal piles

Method of treating organic material. [addition of formate, heating under pressure, and distilling the mass

Energy Technology Data Exchange (ETDEWEB)

Bergstrom, H O.V.; Cederquist, K N

1932-02-08

A method is given of treating organic material such as wood, peat, shale, etc. It is characterized by the addition of formate to the material, before, during, or after heating it under pressure with alkalis, earth alkalis, et cetera, and by the mass thus produced undergoing dry distillation. The patent has three more claims.

Investigation of variation of additional enthalpy of proteins with respect to pH by statistical mechanical methods

International Nuclear Information System (INIS)

Oylumoglu, G.

2005-01-01

In this study variation of additional enthalpy with respect to pH has been investigated by the statistical mechanical methods.. To bring up the additional effect, the partition function of the proteins are calculated by single protein molecule approximation. From the partition function, free energies of the proteins are obtained and by this way additional free energy has been used in the calculation of the terms in the thermodynamical quantity. Additional enthalpy H D has been obtained by taking effective electric field E and constant dipole moment M as thermodynamical variables and using Maxwell Equations. In the presented semi phenomenological theory, necessary data are taken from the experimental study of P.L. Privalov. The variation in the additional enthalpy H D has been investigated in the pH interval of 1-5 and the results of the calculations are discussed for Lysozyme

Method for control-room display design

International Nuclear Information System (INIS)

Montmayeul, R.

1988-01-01

This document describes a method for control-room displays design. It can be used either for isolated display to add to an existing system either for the design of a full system of operator aids. The method is a top-down design with steps of possible iteration. The emphasis is put on display design rather than on system design; system aspects are just mentioned. Advantages of using a method are described [fr

Effect of addition of nitrate fertilizers on the efficient use of ammonium fertilizers uptake in salty soils

International Nuclear Information System (INIS)

Khalifa, Kh.; Zidan, A

1993-01-01

The effect of addition of nitrate fertilizers on the efficient use of ammonium fertilizers was studies using N 15 method, in pot experiment using salt affected alluvial soil, the objective of this study was to determine the ideal ratio of No 3 /NH 4 which enhance the efficiency of ammonium fertilizers. The results showed that the fresh and dry weights of maize (variety LG11) responded significantly to each type of fertilizer alone. Furthermore, the N-NO 3 fertilizer showed superiority over N-NH 4 Fertilizer. Wherever, the highest yield was obtained with a mixture of both (N-NO 3 and N-NH 4 ) with NO 3 /NH 4 ratio 1/8, in spite of the fact that the equivalent amounts of N were employed in all treatments. Under the given circumstances it has been recommended in salt affected soil in dry area, to use the above mentioned ratio for nitrogen fertilizer to obtain optimum yield. (author)

Radiochemical methods and spectroscopical analyses for investigating the catalytic effects of 2-methyltetrahydro-anthraquinone and phenanthraquinone in wood pulp production using the soda additive method

International Nuclear Information System (INIS)

Besser, R. v.

1982-01-01

The studies were to show whether 2-methyltetrahydroanthraquinone or phenanthraquinone, two additives obtainable at low cost, will have a suitable catalytic effect on the delignification using the soda additive pulping method. For this purpose, soda cookings have been made in a 7 l rotary autoclave. The results have shown that 2-MeTHAQ is by far the better catalytic agent. Further experiments have been made to investigate the mode of action of the redox additives, intended to reveal further characteristics which can be correlated with the knowledge obtained from the preceding soda cookings. The analysis shows that there is a connection between the analytical lignin characteristics and the effectiveness of quinoid additives. (orig./PW) [de

The heat insulating properties of potato starch extruded with addition of chosen by- products of food industry

Directory of Open Access Journals (Sweden)

Zdybel Ewa

2014-12-01

Full Text Available The study was aimed at determination of time of heat transition through the layer of quince, apple, linen, rose pomace and potato pulp, as well as layer of potato starch and potato starch extruded with addition of above mentioned by-products. Additionally the attempt of creation a heat insulating barrier from researched raw material was made. The heat conductivity of researched materials was dependent on the type of material and its humidity. Extruded potato starch is characterized by smaller heat conductivity than potato starch extruded with addition of pomace. The obtained rigid extruded starch moulders were characterized by higher heat insulating properties than the loose beads. It is possible to use starch and by-products of food industry for production of heat insulating materials.

Additional Energy Losses from Asymmetric and Non-Sinusoidal Current in an Electrical Facility and Methods of their Reduction

Directory of Open Access Journals (Sweden)

Tarasov Evgeniy V.

2015-01-01

Full Text Available Influence of the asymmetry and higher harmonics of current on the operation of an electrical facility is analyzed. The level of additional losses from the asymmetric and non-sinusoidal currents is evaluated for a 110 kV electrical network in the Siberian Region of the Russian Federation. Methods for reducing the additional energy losses in the electrical facility are suggested.

Additional Energy Losses from Asymmetric and Non-Sinusoidal Current in an Electrical Facility and Methods of their Reduction

OpenAIRE

Tarasov, Evgeny Vladimirovich; Bulyga, Leonid Leonidovich; Ushakov, Vasily Yakovlevich; Kharlov, Nikolay Nikolaevich

2015-01-01

Influence of the asymmetry and higher harmonics of current on the operation of an electrical facility is analyzed. The level of additional losses from the asymmetric and non-sinusoidal currents is evaluated for a 110 kV electrical network in the Siberian Region of the Russian Federation. Methods for reducing the additional energy losses in the electrical facility are suggested.

Detection methods for irradiated food

International Nuclear Information System (INIS)

Stevenson, M.H.

1993-01-01

The plenary lecture gives a brief historical review of the development of methods for the detection of food irradiation and defines the demands on such methods. The methods described in detail are as follows: 1) Physical methods: As examples of luminescence methods, thermoluminescence and chermoluminescence are mentioned; ESR spectroscopy is discussed in detail by means of individual examples (crustaceans, frutis and vegetables, spieces and herbs, nuts). 2) Chemical methods: Examples given for these are methods that make use of alterations in lipids through radiation (formation of long-chain hydrocarbons, formation of 2-alkyl butanones), respectively radiation-induced alterations in the DNA. 3) Microbiological methods. An extensive bibliography is appended. (VHE) [de

Evaporation model for beam based additive manufacturing using free surface lattice Boltzmann methods

International Nuclear Information System (INIS)

Klassen, Alexander; Scharowsky, Thorsten; Körner, Carolin

2014-01-01

Evaporation plays an important role in many technical applications including beam-based additive manufacturing processes, such as selective electron beam or selective laser melting (SEBM/SLM). In this paper, we describe an evaporation model which we employ within the framework of a two-dimensional free surface lattice Boltzmann method. With this method, we solve the hydrodynamics as well as thermodynamics of the molten material taking into account the mass and energy losses due to evaporation and the recoil pressure acting on the melt pool. Validation of the numerical model is performed by measuring maximum melt depths and evaporative losses in samples of pure titanium and Ti–6Al–4V molten by an electron beam. Finally, the model is applied to create processing maps for an SEBM process. The results predict that the penetration depth of the electron beam, which is a function of the acceleration voltage, has a significant influence on evaporation effects. (paper)

A method for additive bias correction in cross-cultural surveys

DEFF Research Database (Denmark)

Scholderer, Joachim; Grunert, Klaus G.; Brunsø, Karen

2001-01-01

additive bias from cross-cultural data. The procedure involves four steps: (1) embed a potentially biased item in a factor-analytic measurement model, (2) test for the existence of additive bias between populations, (3) use the factor-analytic model to estimate the magnitude of the bias, and (4) replace......Measurement bias in cross-cultural surveys can seriously threaten the validity of hypothesis tests. Direct comparisons of means depend on the assumption that differences in observed variables reflect differences in the underlying constructs, and not an additive bias that may be caused by cultural...... differences in the understanding of item wording or response category labels. However, experience suggests that additive bias can be found more often than not. Based on the concept of partial measurement invariance (Byrne, Shavelson and Muthén, 1989), the present paper develops a procedure for eliminating...

Nontargeted Screening Method for Illegal Additives Based on Ultrahigh-Performance Liquid Chromatography-High-Resolution Mass Spectrometry.

Science.gov (United States)

Fu, Yanqing; Zhou, Zhihui; Kong, Hongwei; Lu, Xin; Zhao, Xinjie; Chen, Yihui; Chen, Jia; Wu, Zeming; Xu, Zhiliang; Zhao, Chunxia; Xu, Guowang

2016-09-06

Identification of illegal additives in complex matrixes is important in the food safety field. In this study a nontargeted screening strategy was developed to find illegal additives based on ultrahigh-performance liquid chromatography-high-resolution mass spectrometry (UHPLC-HRMS). First, an analytical method for possible illegal additives in complex matrixes was established including fast sample pretreatment, accurate UHPLC separation, and HRMS detection. Second, efficient data processing and differential analysis workflow were suggested and applied to find potential risk compounds. Third, structure elucidation of risk compounds was performed by (1) searching online databases [Metlin and the Human Metabolome Database (HMDB)] and an in-house database which was established at the above-defined conditions of UHPLC-HRMS analysis and contains information on retention time, mass spectra (MS), and tandem mass spectra (MS/MS) of 475 illegal additives, (2) analyzing fragment ions, and (3) referring to fragmentation rules. Fish was taken as an example to show the usefulness of the nontargeted screening strategy, and six additives were found in suspected fish samples. Quantitative analysis was further carried out to determine the contents of these compounds. The satisfactory application of this strategy in fish samples means that it can also be used in the screening of illegal additives in other kinds of food samples.

On the Complexity of Additively Homomorphic UC Commitments

DEFF Research Database (Denmark)

Trifiletti, Roberto; Nielsen, Jesper Buus; Frederiksen, Tore Kasper

2016-01-01

as the commitment protocol by Garay \\emph{et al.} from Eurocrypt 2014. A main technical improvement over the scheme mentioned above, and other schemes based on using error correcting codes for UC commitment, we develop a new technique which allows to based the extraction property on erasure decoding as opposed...... to error correction. This allows to use a code with significantly smaller minimal distance and allows to use codes without efficient decoding. Our scheme only relies on standard assumptions. Specifically we require a pseudorandom number generator, a linear error correcting code and an ideal oblivious......, we manage to add the additive homo- morphic property, while at the same time reducing the constants. In fact, when opening a large enough batch of commitments we achieve an amor- tized communication complexity converging to the length of the message committed to, i.e., we achieve close to rate 1...

The Role of Noble Metal Addition Methods on BWR Shut Down Dose Rates

International Nuclear Information System (INIS)

Cowan, Robert L.; Garcia Susan, E.

2012-09-01

Noble metal addition technology was developed for the BWR as a means of establishing low electrochemical corrosion potentials (ECP) on structural materials to mitigate intergranular stress corrosion cracking (IGSCC). When the reactor water molar ratio of H 2 / (O 2 +H 2 O 2 ) is > 2 on noble metal treated surfaces, the resulting ECP is near -500 mV (SHE), well into the mitigation range. This ratio can be achieved in most areas of the reactor with feedwater hydrogen additions in the range of 0.2 mg/kg, a condition that does not increase the radiation level in the main steam, a side effect of conventional hydrogen water chemistry (HWC). The resulting low ECP on the surface of stainless steel piping and components results in a change in form of the stable corrosion film to a spinel structure. Since it is the 60 Co incorporated into the corrosion film that is the primary source term of shutdown dose rates in BWRs, the structure and composition of the film can have a large influence in the resulting dose rates. The results of the first generation of noble metal technology, noble metal chemical addition (NMCA), showed that the reactor water ratio of 60 Co (s)/Zn (s) was a key parameter in determining shut down dose rate values. This paper will review that history and provide mechanistic understanding of how initial post NMCA dose rates are established and change with time. On-line noble metal chemical addition (OLNC) is the second generation of noble metal technology. The method utilizes the on-line injection of dilute Na 2 Pt (OH) 6 into the feedwater over a period of approximately 10 days. The first application of OLNC occurred at a European reactor in July of 2005 and to date over 20 BWRs have applied the technology, with many more applications scheduled. It is expected that OLNC will become the de facto standard because it eliminates 60 hours of outage application time and it addresses the crack flanking concerns that can arise under certain conditions. Because both

Additive manufactured serialization

Science.gov (United States)

Bobbitt, III, John T.

2017-04-18

Methods for forming an identifying mark in a structure are described. The method is used in conjunction with an additive manufacturing method and includes the alteration of a process parameter during the manufacturing process. The method can form in a unique identifying mark within or on the surface of a structure that is virtually impossible to be replicated. Methods can provide a high level of confidence that the identifying mark will remain unaltered on the formed structure.

Fuzzy Simple Additive Weighting Method in the Decision Making of Human Resource Recruitment

Directory of Open Access Journals (Sweden)

Budi Prasetiyo

2016-12-01

Full Text Available The Company is one of the jobs that was founded to reduce unemployment. The progress of a company is determined by the human resources that exist within the company. So, the selection of workers will join the company need to be selected first. The hardest thing in making a selection factor is the effort to eliminate the subjectivity of the personnel manager so that every choice made is objective based on the criteria expected by the company. To help determine who is accepted as an employee in the company, we need a method that can provide a valid decision. Therefore, we use Fuzzy Multiple Attribute Decision Making with Simple Additive Weighting method (SAW to decide to make in human resource recruitment. This method was chosen because it can provide the best alternative from several alternatives. In this case, the alternative is that the applicants or candidates. This research was conducted by finding the weight values for each attribute. Then do the ranking process that determines the optimal alternative to the best applicants who qualify as employees of the company. Based on calculations by the SAW obtained the two highest ranking results are A5 (alternative 5 and A1 (alternative 1, to obtain two candidates received.

Viability Study of a Safe Method for Health to Prepare Cement Pastes with Simultaneous Nanometric Functional Additions

Directory of Open Access Journals (Sweden)

M. A. de la Rubia

2018-01-01

Full Text Available The use of a mixing method based on a novel dry dispersion procedure that enables a proper mixing of simultaneous nanometric functional additions while avoiding the health risks derived from the exposure to nanoparticles is reported and compared with a common manual mixing in this work. Such a dry dispersion method allows a greater workability by avoiding problems associated with the dispersion of the particles. The two mixing methods have been used to prepare Portland cement CEM I 52.5R pastes with additions of nano-ZnO with bactericide properties and micro- or nanopozzolanic SiO2. The hydration process performed by both mixing methods is compared in order to determine the efficiency of using the method. The hydration analysis of these cement pastes is carried out at different ages (from one to twenty-eight days by means of differential thermal analysis and thermogravimetry (DTA-TG, X-ray diffraction (XRD, scanning electron microscopy (SEM, and Fourier transform infrared spectroscopy (FTIR analyses. Regardless of composition, all the mixtures of cement pastes obtained by the novel dispersion method showed a higher retardation of cement hydration at intermediate ages which did not occur at higher ages. In agreement with the resulting hydration behaviour, the use of this new dispersion method makes it possible to prepare homogeneous cement pastes with simultaneous functional nanoparticles which are physically supported on the larger particles of cement, avoiding exposure to the nanoparticles and therefore minimizing health risks. Manual mixing of cement-based materials with simultaneous nanometric functional nanoparticles on a large scale would make it difficult to obtain a homogenous material together with the health risks derived from the handling of nanoparticles.

Strong-stability-preserving additive linear multistep methods

KAUST Repository

Hadjimichael, Yiannis; Ketcheson, David I.

2018-01-01

The analysis of strong-stability-preserving (SSP) linear multistep methods is extended to semi-discretized problems for which different terms on the right-hand side satisfy different forward Euler (or circle) conditions. Optimal perturbed

Synthesis of YBa2Cu3O7-y from nitrate solutions with urea additions

International Nuclear Information System (INIS)

Pershin, V.I.; Naumov, V.S.; Mozhaev, A.P.; Lyashchenko, A.K.; Pobedina, A.B.; Khajlova, E.G.

1994-01-01

Solubility of bariun nitrate is studied in the Y(NO 3 ) 3 -Ba(NO 3 ) 2 -Cu(NO 3 )-CO(NH 2 ) 2 -H 2 O system at the ratio Y:B:Cu-1:2:3 and variable concentration of urea in the solution. Mentioned aqua-salt compositions are used in cryochemical synthesis of HTSC. Solutions of yttrium, barium and copper nitrates with urea additions were demonstrated to be recommended to improvements in the process during development of alternative synthesis from aqua-salt compositions. 15 refs., 3 figs., 2 tabs

River catchment rainfall series analysis using additive Holt-Winters method

Science.gov (United States)

Puah, Yan Jun; Huang, Yuk Feng; Chua, Kuan Chin; Lee, Teang Shui

2016-03-01

Climate change is receiving more attention from researchers as the frequency of occurrence of severe natural disasters is getting higher. Tropical countries like Malaysia have no distinct four seasons; rainfall has become the popular parameter to assess climate change. Conventional ways that determine rainfall trends can only provide a general result in single direction for the whole study period. In this study, rainfall series were modelled using additive Holt-Winters method to examine the rainfall pattern in Langat River Basin, Malaysia. Nine homogeneous series of more than 25 years data and less than 10% missing data were selected. Goodness of fit of the forecasted models was measured. It was found that seasonal rainfall model forecasts are generally better than the monthly rainfall model forecasts. Three stations in the western region exhibited increasing trend. Rainfall in southern region showed fluctuation. Increasing trends were discovered at stations in the south-eastern region except the seasonal analysis at station 45253. Decreasing trend was found at station 2818110 in the east, while increasing trend was shown at station 44320 that represents the north-eastern region. The accuracies of both rainfall model forecasts were tested using the recorded data of years 2010-2012. Most of the forecasts are acceptable.

Soup Cooking by Thermal Insulation Method

OpenAIRE

佐藤, 辰江; 根本, 勢子; サトウ, タツエ; ネモト, セイコ; TATSUE, SATO; SEIKO, NEMOTO

1992-01-01

In order to examine the thermal insulation method of soup cooking, we cooked two kinds of soup. The soup cooked by thermal insulation method was compared with the soup cooked by standard boiling method. ln sensory test, it was more aromatic and palatable than the soup by boiling, and some panels commented that it was rather mild. The measured values of pH, specific gravity, acidity and amount of dry weight of souble solids, total-N, formal-N of the soup cooked by the two methods mentioned abo...

Effects of an additional small group discussion to cognitive achievement and retention in basic principles of bioethics teaching methods

Directory of Open Access Journals (Sweden)

Dedi Afandi

2009-03-01

Full Text Available Aim The place of ethics in undergraduate medical curricula is essential but the methods of teaching medical ethics did not show substantial changes. “Basic principles of bioethics” is the best knowledge to develop student’s reasoning analysis in medical ethics In this study, we investigate the effects of an additional small group discussion in basic principles of bioethics conventional lecture methods to cognitive achievement and retention. This study was a randomized controlled trial with parallel design. Cognitive scores of the basic principles of bioethics as a parameter was measured using basic principles of bioethics (Kaidah Dasar Bioetika, KDB test. Both groups were attending conventional lectures, then the intervention group got an additional small group discussion.Result Conventional lectures with or without small group discussion significantly increased cognitive achievement of basic principles of bioethics (P= 0.001 and P= 0.000, respectively, and there were significant differences in cognitive achievement and retention between the 2 groups (P= 0.000 and P= 0.000, respectively.Conclusion Additional small group discussion method improved cognitive achievement and retention of basic principles of bioethics. (Med J Indones 2009; 18: 48-52Keywords: lecture, specification checklist, multiple choice questions

The effect of nitrate addition on efficient use of ammonium sulfate fertilizer under saline soil condition

International Nuclear Information System (INIS)

Khalifa, KH.; Zedan, A.

1996-01-01

The effect of addition of nitrate fertilizers on the efficient use of ammonium fertilizers was studied using N sub 1 sub 5 method. In pot experiment using salt affected alluvial soil, the objective of this study was to determine the ideal ratio of NO sub 3/NH sub 4 which enhance the efficiency of ammonium fertilizers. The results showed that the fresh and dry weights of maize (variety LG11) responded significantly to each type of fertilizer alone. Furthermore, the N-NO sub 3 fertilizer showed superiority over N-NH sup 4 fertilizer. Wherever, the highest yield was obtained with a mixture of both (N-NO sub 3 and N-NH sub 4) with NO sub 3/NH sub 4 ratio 1/8, in spite of the fact that the equivalent amounts of N were employed in all treatments. Under the given circumstances it has been recommended in salt affected soil in dry area, to use the above mentioned ratio for nitrogen fertilizer to obtain optimum yield. (author). 8 refs., 3 tabs

Methods employed in the prevention and treatment of malaria ...

African Journals Online (AJOL)

onasoga olayinka

of malaria among pregnant women in riverine community in Bayelsa State, ... at high risk of the effects of malaria infection and need special protective .... mentioned maintenance of clean environment, as other methods of preventing malaria.

Additive operator-difference schemes splitting schemes

CERN Document Server

Vabishchevich, Petr N

2013-01-01

Applied mathematical modeling isconcerned with solving unsteady problems. This bookshows how toconstruct additive difference schemes to solve approximately unsteady multi-dimensional problems for PDEs. Two classes of schemes are highlighted: methods of splitting with respect to spatial variables (alternating direction methods) and schemes of splitting into physical processes. Also regionally additive schemes (domain decomposition methods)and unconditionally stable additive schemes of multi-component splitting are considered for evolutionary equations of first and second order as well as for sy

Utility of noise addition image made by using water phantom and image addition and subtraction software

International Nuclear Information System (INIS)

Watanabe, Ryo; Aoki, Takahiro; Hayano, Mizuho; Ogawa, Masato; Mituzono, Hiroki; Watanabe, Yuka

2010-01-01

In optimizing exposures, it is very important to evaluate the impact of image noise on image quality. To realize this, there is a need to evaluate how much image noise will make the subject disease invisible. But generally it is very difficult to shoot images of different quality in a clinical examination. Thus, a method to create a noise addition image by adding the image noise to raw data has been reported. However, this approach requires a special system, so it is difficult to implement in many facilities. We have invented a method to easily create a noise addition image by using the water phantom and image add-subtract software that accompanies the device. To create a noise addition image, first we made a noise image by subtracting the water phantom with different standard deviation (SD). A noise addition image was then created by adding the noise image to the original image. By using this method, a simulation image with intergraded SD can be created from the original. Moreover, the noise frequency component of the created noise addition image is as same as the real image. Thus, the relationship of image quality to SD in the clinical image can be evaluated. Although this method is an easy method of LDSI creation on image data, a noise addition image can be easily created by using image addition and subtraction software and water phantom, and this can be implemented in many facilities. (author)

ORGANIZATIONAL AND METHODICAL BASES OF MULTICULTURAL SELF-ORGANIZATION OF STUDENTS IN THE ADDITIONAL FOREIGN LANGUAGE EDUCATION

Directory of Open Access Journals (Sweden)

V N Kartashova

2016-12-01

Full Text Available The article deals with the organizational and methodical bases of multicultural self-organization of the linguistic personality of the student in terms of additional foreign language education. According to the authors’ opinion, the methodological basis is a dialogue of cultures as a philosophy of mutual understanding, mutual relations in today’s global environment. Changing the socio-cultural context of foreign language education paradigm allows you to select multicultural (teaching a foreign language on the principle of “native culture - the culture of the foreign language speaking country - the culture of the world” and active (the development and functioning of a person in the normal course of his activities, where the starting point is the introduction of man to the world of culture and his self-development approach as a priority. The contents of additional education is oriented towards the disclosure and a possible solution of specific problems in the educational practice, and based on the principles of humanism and diversification.The article analyzes the individual programs of additional education and professional training in the field of foreign languages, developed by universities in recent decades. The authors present the experience of the scientific and methodological development and implementation at the department of foreign languages and teaching methods of Bunin Yelets State University of the additional foreign language education system that provides the multicultural self-organization of the student’s linguistic personality. The description of the program of professional retraining “The multicultural self-organization expert in the field of business, management and tourism (English”, designed for the students of non-language training areas, is presented, too. The positive dynamics of mastering foreign languages, the development of global attitude of the linguistic personality to the culture and his/her cultural

Source Distribution Method for Unsteady One-Dimensional Flows With Small Mass, Momentum, and Heat Addition and Small Area Variation

Science.gov (United States)

Mirels, Harold

1959-01-01

A source distribution method is presented for obtaining flow perturbations due to small unsteady area variations, mass, momentum, and heat additions in a basic uniform (or piecewise uniform) one-dimensional flow. First, the perturbations due to an elemental area variation, mass, momentum, and heat addition are found. The general solution is then represented by a spatial and temporal distribution of these elemental (source) solutions. Emphasis is placed on discussing the physical nature of the flow phenomena. The method is illustrated by several examples. These include the determination of perturbations in basic flows consisting of (1) a shock propagating through a nonuniform tube, (2) a constant-velocity piston driving a shock, (3) ideal shock-tube flows, and (4) deflagrations initiated at a closed end. The method is particularly applicable for finding the perturbations due to relatively thin wall boundary layers.

EXPLORATION BY MEANS OF GEOPHYSICAL METHODS OF GEOTHERMAL FIELDS AND CASE STUDIES

Directory of Open Access Journals (Sweden)

Züheyr KAMACI

1997-01-01

Full Text Available Geothermal energy which is one of the reuseable energy resources, can save as much as 77 million barrels of petroleum equivalent annually when used in the production of electricity and heating-environment. Geophysical exploration methods plays in important role in the fields of geothermal exploration, development and observational studies. Thermal and geoelectrical methods are the most effective methods which shows the temperature variation anomalies and mechanical drilling places. But, when the other methods of gravity, magnetic, radiometric, well geophysics and well logs can be used in conjunction with seismic tomography, apart from the mentioned geophysical exploration method, better results could be obtained. From the above mentioned facts various case history reports are given from our country and worldwide to determine geothermal energy resources by using geophysical exploration technique application. From these results of studies a 55 °C hot water artessian aquifer is found in the Uşak-Banaz geothermal field by applying geoelectrical methods.

Refining Measurement of Substance Use Disorders Among Women of Child-Bearing Age Using Hospital Records: The Development of the Explicit-Mention Substance Abuse Need for Treatment in Women (EMSANT-W) Algorithm.

Science.gov (United States)

Derrington, Taletha Mae; Bernstein, Judith; Belanoff, Candice; Cabral, Howard J; Babakhanlou-Chase, Hermik; Diop, Hafsatou; Evans, Stephen R; Kotelchuck, Milton

2015-10-01

Substance use disorder (SUD) in women of reproductive age is associated with adverse health consequences for both women and their offspring. US states need a feasible population-based, case-identification tool to generate better approximations of SUD prevalence, treatment use, and treatment outcomes among women. This article presents the development of the Explicit Mention Substance Abuse Need for Treatment in Women (EMSANT-W), a gender-tailored tool based upon existing International Classification of Diseases, 9th Edition, Clinical Modification diagnostic code-based groupers that can be applied to hospital administrative data. Gender-tailoring entailed the addition of codes related to infants, pregnancy, and prescription drug abuse, as well as the creation of inclusion/exclusion rules based on other conditions present in the diagnostic record. Among 1,728,027 women and associated infants who accessed hospital care from January 1, 2002 to December 31, 2008 in Massachusetts, EMSANT-W identified 103,059 women with probable SUD. EMSANT-W identified 4,116 women who were not identified by the widely used Clinical Classifications Software for Mental Health and Substance Abuse (CCS-MHSA) and did not capture 853 women identified by CCS-MHSA. Content and approach innovations in EMSANT-W address potential limitations of the Clinical Classifications Software, and create a methodologically sound, gender-tailored and feasible population-based tool for identifying women of reproductive age in need of further evaluation for SUD treatment. Rapid changes in health care service infrastructure, delivery systems and policies require tools such as the EMSANT-W that provide more precise identification methods for sub-populations and can serve as the foundation for analyses of treatment use and outcomes.

Ultrasonography as a diagnostic method in addition to mammography

Energy Technology Data Exchange (ETDEWEB)

Otto, H.; Roer, E.

1988-05-01

By using ultrasonography in addition to mammography, experienced diagnosticians essentially enhance the safety of their diagnosis of mammary gland diseases. The same applies to gynecomastia, the condition after plastic surgery, and mastitis.

Application of revised procedure on determining large excess reactivity of operating reactor. Fuel addition method

International Nuclear Information System (INIS)

Nagao, Yoshiharu

2002-01-01

The fuel addition method or the neutron absorption substitution method have been used for determination of large excess multiplication factor of large sized reactors. It has been pointed out, however, that all the experimental methods are possibly not free from the substantially large systematic error up to 20%, when the value of the excess multiplication factor exceeds about 15%Δk. Then, a basic idea of a revised procedure was proposed to cope with the problem, which converts the increase of multiplication factor in an actual core to that in a virtual core by calculation, because its value is in principle defined not for the former but the latter core. This paper proves that the revised procedure is able to be applicable for large sized research and test reactors through the theoretical analyses on the measurements undertaken at the JMTRC and JMTR cores. The values of excess multiplication factor are accurately determined utilizing the whole core calculation by the Monte Carlo code MCNP4A. (author)

Concept of Sukha (comfort) mentioned in Dhatusarata (tissue excellence) w.s.r. to vocational guidance

Science.gov (United States)

Waghulade, Hemangini; Harit, Mahesh Kumar

2014-01-01

Agni (digestive fire), Prakruti (constitution), Dhatusarata (tissue excellence), Dosha (bio–energies) are the specialties of Ayurveda on which diagnosis, treatment and research are based. The description of Dhatusarata (tissue excellence) has been given under Dashavidha Pariksha (tenfold examination) in Charak Samhita, Viman Sthana, 8th chapter. Some qualities, which are mentioned in Dhatusarata are difficult to assess, e.g. Sukha, Aishwarya, Upabhoga, Bala, etc., There is a need to develop some quantitative parameters to measure these qualities according to tissue excellence i.e. Dhatusarata. By assessing Dhatu Sarata, one can judge the true strength of a particular Dhatu but only the ability or strength is not enough to get success; the liking or interest is also essential to achieve success. The purpose of this study is to elaborate the concept of Dhatusarata and reveal different aspects of Sukha according to the quality of that particular Dhatu in context of vocational guidance. It will help to establish interrelationship between Dhatusarata and vocational guidance. It will be assessed whether this Sukha quality is merely happiness or having different shades according to the excellence of Dhatus and whether this study is useful in guiding the person to choose appropriate profession, which will be according to his liking and ability. It has been concluded that shades of Sukha quality varies with particular Dhatusaras, which may be helpful in guiding a suitable profession to an individual which will be according to his ability and liking i.e. Sukha for intimate success. PMID:26195895

Analysis of the essential oils of Alpiniae Officinarum Hance in different extraction methods

Science.gov (United States)

Yuan, Y.; Lin, L. J.; Huang, X. B.; Li, J. H.

2017-09-01

It was developed for the analysis of the essential oils of Alpiniae Officinarum Hance extracted by steam distillation (SD), ultrasonic assisted solvent extraction (UAE) and supercritical fluid extraction (SFE) via gas chromatography mass spectrometry (GC-MS) combined with retention index (RI) method. There were multiple volatile components of the oils extracted by the three above-mention methods respectively identified; meanwhile, each one was quantified by area normalization method. The results indicated that the content of 1,8-Cineole, the index constituent, by SD was similar as SFE, and higher than UAE. Although UAE was less time consuming and consumed less energy, the oil quality was poorer due to the use of organic solvents was hard to degrade. In addition, some constituents could be obtained by SFE but could not by SD. In conclusion, essential oil of different extraction methods from the same batch of materials had been proved broadly similarly, however, there were some differences in composition and component ratio. Therefore, development and utilization of different extraction methods must be selected according to the functional requirements of products.

How to gain additional knowledge in the situation when university degrees (no longer guarantee suitable employment

Directory of Open Access Journals (Sweden)

Darka Podmenik

2011-03-01

The article deals with two issues related to the above­mentioned findings: – what to do to alleviate the consequences of the factors pushing the young to the margins of the society, emphasizing the need for investment in (additional education and establishment of social networks; and, – whether the young who have acquired the highest levels of education (the group that loses most knowledge if doomed to an unsuitable career could improve their ability to make a successful education­ career transition by investing more in human and social capital.

Method for mapping population-based case-control studies: an application using generalized additive models

Directory of Open Access Journals (Sweden)

Aschengrau Ann

2006-06-01

Full Text Available Abstract Background Mapping spatial distributions of disease occurrence and risk can serve as a useful tool for identifying exposures of public health concern. Disease registry data are often mapped by town or county of diagnosis and contain limited data on covariates. These maps often possess poor spatial resolution, the potential for spatial confounding, and the inability to consider latency. Population-based case-control studies can provide detailed information on residential history and covariates. Results Generalized additive models (GAMs provide a useful framework for mapping point-based epidemiologic data. Smoothing on location while controlling for covariates produces adjusted maps. We generate maps of odds ratios using the entire study area as a reference. We smooth using a locally weighted regression smoother (loess, a method that combines the advantages of nearest neighbor and kernel methods. We choose an optimal degree of smoothing by minimizing Akaike's Information Criterion. We use a deviance-based test to assess the overall importance of location in the model and pointwise permutation tests to locate regions of significantly increased or decreased risk. The method is illustrated with synthetic data and data from a population-based case-control study, using S-Plus and ArcView software. Conclusion Our goal is to develop practical methods for mapping population-based case-control and cohort studies. The method described here performs well for our synthetic data, reproducing important features of the data and adequately controlling the covariate. When applied to the population-based case-control data set, the method suggests spatial confounding and identifies statistically significant areas of increased and decreased odds ratios.

A Comparison of Distillery Stillage Disposal Methods

OpenAIRE

V. Sajbrt; M. Rosol; P. Ditl

2010-01-01

This paper compares the main stillage disposal methods from the point of view of technology, economics and energetics. Attention is paid to the disposal of both solid and liquid phase. Specifically, the following methods are considered: a) livestock feeding, b) combustion of granulated stillages, c) fertilizer production, d) anaerobic digestion with biogas production and e) chemical pretreatment and subsequent secondary treatment. Other disposal techniques mentioned in the literature (electro...

Comparison of simple additive weighting (SAW) and composite performance index (CPI) methods in employee remuneration determination

Science.gov (United States)

Karlitasari, L.; Suhartini, D.; Benny

2017-01-01

The process of determining the employee remuneration for PT Sepatu Mas Idaman currently are still using Microsoft Excel-based spreadsheet where in the spreadsheet there is the value of criterias that must be calculated for every employee. This can give the effect of doubt during the assesment process, therefore resulting in the process to take much longer time. The process of employee remuneration determination is conducted by the assesment team based on some criterias that have been predetermined. The criteria used in the assessment process are namely the ability to work, human relations, job responsibility, discipline, creativity, work, achievement of targets, and absence. To ease the determination of employee remuneration to be more efficient and effective, the Simple Additive Weighting (SAW) method is used. SAW method can help in decision making for a certain case, and the calculation that generates the greatest value will be chosen as the best alternative. Other than SAW, also by using another method was the CPI method which is one of the calculating method in decision making based on performance index. Where SAW method was more faster by 89-93% compared to CPI method. Therefore it is expected that this application can be an evaluation material for the need of training and development for employee performances to be more optimal.

Catalyst-free and solvent-free Michael addition of 1,3-dicarbonyl compounds to nitroalkenes by a grinding method

Science.gov (United States)

Xie, Zong-Bo; Wu, Ming-Yu; He, Ting; Le, Zhang-Gao

2012-01-01

Summary An environmentally benign, fast and convenient protocol has been developed for the Michael addition of 1,3-dicarbonyl compounds to β-nitroalkenes in good to excellent yields by a grinding method under catalyst- and solvent-free conditions. PMID:22563352

Computer programs in BASIC language for graphite furnace atomic absorption using the method of additions. Part 2. Documentation

International Nuclear Information System (INIS)

Boyle, W.G. Jr.; Ryan, D.P.

1979-08-01

There are four computer programs, written in the BASIC language, used for taking and processing data from an atomic absorption spectrophotometer using the graphite furnace and the method of additions for calibration. The programs chain to each other and are divided into logical sections that have been flow-charted. The chaining sequences, general features, structure, order of subroutines and functions, and the storage of data are discussed. In addition, variables are listed and defined, and a complete listing of each program with a symbol occurrence table is provided

Net analyte signal standard addition method for simultaneous determination of sulphadiazine and trimethoprim in bovine milk and veterinary medicines.

Science.gov (United States)

Hajian, Reza; Mousavi, Esmat; Shams, Nafiseh

2013-06-01

Net analyte signal standard addition method has been used for the simultaneous determination of sulphadiazine and trimethoprim by spectrophotometry in some bovine milk and veterinary medicines. The method combines the advantages of standard addition method with the net analyte signal concept which enables the extraction of information concerning a certain analyte from spectra of multi-component mixtures. This method has some advantages such as the use of a full spectrum realisation, therefore it does not require calibration and prediction step and only a few measurements require for the determination. Cloud point extraction based on the phenomenon of solubilisation used for extraction of sulphadiazine and trimethoprim in bovine milk. It is based on the induction of micellar organised media by using Triton X-100 as an extraction solvent. At the optimum conditions, the norm of NAS vectors increased linearly with concentrations in the range of 1.0-150.0 μmolL(-1) for both sulphadiazine and trimethoprim. The limits of detection (LOD) for sulphadiazine and trimethoprim were 0.86 and 0.92 μmolL(-1), respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

A method for the preparation of a fuel, by the addition of one or more components to a base fuel

NARCIS (Netherlands)

2013-01-01

The present invention relates to a method for the preparation of a fuel, by the addition of one or more components to a base fuel, wherein the method comprises the following steps: i) providing a base fuel; ii) withdrawing aromatic components from a styrene / propylene ox ide production plant; iii)

Improvement in retention of solid fission products in HTGR fuel particles by ceramic kernel additives

International Nuclear Information System (INIS)

Foerthmann, R.; Groos, E.; Gruebmeier, H.

1975-08-01

Increased requirements concerning the retention of long-lived solid fission products in fuel elements for use in advanced High Temperature Gas-cooled Reactors led to the development of coated particles with improved fission product retention of the kernel, which represent an alternative to silicon carbide-coated fuel particles. Two irradiation experiments have shown that the release of strontium, barium, and caesium from pyrocarbon-coated particles can be reduced by orders of magnitude if the oxide kernel contains alumina-silica additives. It was detected by electron microprobe analysis that the improved retention of the mentioned fission products in the fuel kernel is caused by formation of the stable aluminosilicates SrAl 2 Si 2 O 8 , BaAl 2 Si 2 O 8 and CsAlSi 2 O 6 in the additional aluminasilica phase of the kernel. (orig.) [de

QUALITATIVE METHODS IN CREATIVITY STUDIES

DEFF Research Database (Denmark)

Hertel, Frederik

2015-01-01

In this article we will focus on developing a qualitative research design suitable for conducting case study in creativity. The case is a team of workers (See Hertel, 2015) doing industrial cleaning in the Danish food industry. The hypothesis is that these workers are both participating in......-specific methods, involving a discussion of creativity test, divergent and convergent thinking, for studying creativity in this specific setting. Beside from that we will develop a research design involving a combination of methods necessary for conducting a case study in the setting mentioned....

Additivity methods for prediction of thermochemical properties. The Laidler method revisited. 2. Hydrocarbons including substituted cyclic compounds

International Nuclear Information System (INIS)

Santos, Rui C.; Leal, Joao P.; Martinho Simoes, Jose A.

2009-01-01

A revised parameterization of the extended Laidler method for predicting standard molar enthalpies of atomization and standard molar enthalpies of formation at T = 298.15 K for several families of hydrocarbons (alkanes, alkenes, alkynes, polyenes, poly-ynes, cycloalkanes, substituted cycloalkanes, cycloalkenes, substituted cycloalkenes, benzene derivatives, and bi and polyphenyls) is presented. Data for a total of 265 gas-phase and 242 liquid-phase compounds were used for the calculation of the parameters. Comparison of the experimental values with those obtained using the additive scheme led to an average absolute difference of 0.73 kJ . mol -1 for the gas-phase standard molar enthalpy of formation and 0.79 kJ . mol -1 for the liquid-phase standard molar enthalpy of formation. The database used to establish the parameters was carefully reviewed by using, whenever possible, the original publications. A worksheet to simplify the calculation of standard molar enthalpies of formation and standard molar enthalpies of atomization at T = 298.15 K based on the extended Laidler parameters defined in this paper is provided as supplementary material.

Reducing the ordering temperature of FePt nanoparticles by Cu additive and alternate reduction method

Directory of Open Access Journals (Sweden)

Fang Wang

2017-12-01

Full Text Available (FePt85Cu15 nanoparticles were successfully prepared by alternate reduction of metal salts in aqueous medium. Detailed investigations on the correlation between the magnetic and structural properties of these nanoparticles are presented as a function of annealing temperature. Both the X-ray diffraction patterns and the magnetic hysteresis loop measurements show the existence of L10-FePt phase at a relative low annealing temperature. It is proved that the Cu additive and alternate reduction are very effective methods in reducing the ordering temperature of FePt nanoparticles.

Formic acid as additive for the preparation of high-performance FePO4 materials by spray drying method

CSIR Research Space (South Africa)

Yanga, F

2017-12-01

Full Text Available International, vol. 43(18): 16652-16658 Formic acid as additive for the preparation of high-performance FePO4 materials by spray drying method Yanga F Zhang H Shao Y Song H Liao S Ren J ABSTRACT: High-performance ferric phosphate (FePO4...

Method of controlling the water quality in nuclear reactors

International Nuclear Information System (INIS)

Ibe, Hidefumi.

1985-01-01

Purpose: To obtain a simple and reliable water quality calculation system and water quality control method based thereon for the entire primary coolant circuits in BWR type reactors. Method: In a method of controlling the water quality of the reactor water by injecting hydrogen into the primary coolant circuits of a nuclear reactor, by utilizing a first linear relationship established between the concentration of oxygen and hydrogen in the main steam system and the concentration of radiolysis products in the reactor core and separators and mixing plenum portions, each of the above-mentioned concentrations is calculated from the concentrations for hydrogen or oxygen. Further, by utilizing the first linear relationship established between the concentrations for the oxygen and hydrogen in the recycling system and the concentration of the radiolysis products in the system from the downcomer to the lower plenum portion, the above-mentioned concentration is calculated from the concentration for oxygen and hydrogen. Then, the hydrogen injection rate into the primary coolant system is determined such that the calculated value takes an aimed value. (Ikeda, J.)

IMPLEMENTATION OF SIMPLE ADDITIVE WEIGHTING (SAW METHODE IN DETERMINING HIGH SCHOOL STUDENT’S INTEREST

Directory of Open Access Journals (Sweden)

Prind Triajeng Pungkasanti

2017-09-01

Full Text Available The Ministry of Research, Technology, and Higher Education of Republic of Indonesia has set a regulation about curriculum applied in education field named Kurikulum 2013. One of the subsections in the Kurikulum 2013 regulates all requirements of majoring in high school. High school students determine their major based on Kurrikulum 2013 as they are on the 10th grade. The purpose of the majoring in education is to allow children development based on their skills and interests, because before, majoring have been done based on scores obtained. The main problem is the majoring requirements considered are admission test score and Junior High School National Test score. Both scores are not sufficient enough to determine the students major therefore academic aptitude test score is required. In term of weighting, the school has not been imposed the weighting system so the scores obtained is the average of admission test score and national test score. Based on the issue above, a solution required to solve the issue using a method. Method used in this research is Simple Additive Weighting (SAW, wherein this methode is looking for the weighted sum of performance rate on every alternative of atributes. This research provides the information about which potential students is suitable to enter the science major and social major so this results can be used as consideration of school decisions.

Identification of irradiated food additives by photostimulated luminescence (PSL) method

International Nuclear Information System (INIS)

Yun, Hye Jeong; Kwon, Joong Ho; KIm, Dong Ho; Hur, Jung Mu; Yang, Suh Yung; Lee, Byoung Hun

2008-01-01

Photostimulated luminescence (PSL), electron spin resonance (ESR) and thermoluminescence (TL) analyses were conducted to detect whether 258 kinds of extracted and powdered forms food additives were irradiated or not. In a view of the PSL results, 9 kinds of the extracted and powdered samples (3.2%) showed over 5,000 photon counts (60 sec) -1 and these samples were judged to be irradiation-positive. Thirty nine kinds of the samples (15.6%) yielded 700-5,000 photon counts (60 sec) -1 and these samples were grouped into irradiation-potential, while the samples showed below 700 photon counts (60 sec) -1 sec were judged to be irradiation-negative. TL glow curves for minerals separated from 5 samples were detected at 150 degrees C with high intensity. However, TL analysis did not apply to other irradiation-positive and irradiation-potential samples because the minerals for TL detection were not separated from the samples. ESR measurements for irradiation-positive and irradiation-potential samples, judged by PSL detection, showed no specific signals to irradiation. The results indicated that PSL could be applied to identify irradiation treatment of extracted and powdered food additives, while TL was optional and ESR was not suitable for detection extracted and powdered food additives

Stability of a Generalized Euler-Lagrange Type Additive Mapping and Homomorphisms in C∗-Algebras

Directory of Open Access Journals (Sweden)

Abbas Najati

2009-01-01

Full Text Available Let X,Y be Banach modules over a C∗-algebra and let r1,…,rn∈ℝ be given. We prove the generalized Hyers-Ulam stability of the following functional equation in Banach modules over a unital C∗-algebra: ∑j=1nf(−rjxj+∑1≤i≤n,i≠jrixi+2∑i=1nrif(xi=nf(∑i=1nrixi. We show that if ∑i=1nri≠0, ri,rj≠0 for some 1≤imentioned above then the mapping f:X→Y is Cauchy additive. As an application, we investigate homomorphisms in unital C∗-algebras.

Decision Support System to Choose Digital Single Lens Camera with Simple Additive Weighting Method

Directory of Open Access Journals (Sweden)

Tri Pina Putri

2016-11-01

Full Text Available One of the technologies that evolve today is Digital Single Lens Reflex (DSLR camera. The number of products makes users have difficulties to choose the appropriate camera based on their criteria. Users may utilize several ways to help them choosing the intended camera such as using magazine, internet, and other media. This paper discusses about a web based decision support system to choose cameras by using SAW (Simple Additive Weighting method in order to make the decision process more effective and efficient. This system is expected to give recommendations about the camera which is appropriate with the user’s need and criteria based on the cost, the resolution, the feature, the ISO, and the censor. The system was implemented by using PHP and MySQL. Based on the result of questionnaire distributed to 20 respondents, 60% respondents agree that this decision support system can help users to choose the appropriate camera DSLR in accordance with the user’s need, 60% of respondents agree that this decision support system is more effective to choose DSLR camera and 75% of respondents agree that this system is more efficient. In addition, 60.55% of respondents agree that this system has met 5 Es Usability Framework.

Computer programs in BASIC language for graphite furnace atomic absorption using the method of additions. Part 1. Operating instructions

International Nuclear Information System (INIS)

Boyle, W.G. Jr.; Ryan, D.P.

1979-01-01

These instructions describe how to use BASIC language programs to process data from atomic absorption spectrophotometers using the graphite furnace and the method of additions calibration technique. The instructions cover loading the programs, responding to computer prompts, choosing among various options for processing the data, performing operations with an automatic sampler, and producing reports. How the programs interact with each other is also explained. Examples of computer/operator dialogue are presented for typical cases. In addition, a concise set of operating instructions is included as an appendix

Research on interpolation methods in medical image processing.

Science.gov (United States)

Pan, Mei-Sen; Yang, Xiao-Li; Tang, Jing-Tian

2012-04-01

Image interpolation is widely used for the field of medical image processing. In this paper, interpolation methods are divided into three groups: filter interpolation, ordinary interpolation and general partial volume interpolation. Some commonly-used filter methods for image interpolation are pioneered, but the interpolation effects need to be further improved. When analyzing and discussing ordinary interpolation, many asymmetrical kernel interpolation methods are proposed. Compared with symmetrical kernel ones, the former are have some advantages. After analyzing the partial volume and generalized partial volume estimation interpolations, the new concept and constraint conditions of the general partial volume interpolation are defined, and several new partial volume interpolation functions are derived. By performing the experiments of image scaling, rotation and self-registration, the interpolation methods mentioned in this paper are compared in the entropy, peak signal-to-noise ratio, cross entropy, normalized cross-correlation coefficient and running time. Among the filter interpolation methods, the median and B-spline filter interpolations have a relatively better interpolating performance. Among the ordinary interpolation methods, on the whole, the symmetrical cubic kernel interpolations demonstrate a strong advantage, especially the symmetrical cubic B-spline interpolation. However, we have to mention that they are very time-consuming and have lower time efficiency. As for the general partial volume interpolation methods, from the total error of image self-registration, the symmetrical interpolations provide certain superiority; but considering the processing efficiency, the asymmetrical interpolations are better.

Improvement in retention of solid fission products in HTGR fuel particles by ceramic kernel additives

Energy Technology Data Exchange (ETDEWEB)

Foerthmann, R.; Groos, E.; Gruebmeier, H.

1975-08-15

Increased requirements concerning the retention of long-lived solid fission products in fuel elements for use in advanced High Temperature Gas-cooled Reactors led to the development of coated particles with improved fission product retention which represent an alternative to silicon carbide-coated fuel particles. Two irradiation experiments have shown that the release of strontium, barium, and caesium from pyrocarbon-coated particles can be reduced by orders of magnitude if the oxide kernel contains alumina-silica additives. It was detected by electron microprobe analysis that the improved retention of the mentioned fission products in the fuel kernel is caused by formation of the stable aluminosilicates SrAl₂Si₂O₈, BaAl₂Si₂O₈and CsAlSi₂O₆ in the additional alumina-silica phase of the kernel.

[Rapid determination of illicit beta2-agonist additives in health foods and traditional Chinese patent medicines with DCBI-MS/MS method].

Science.gov (United States)

Hou, Yu-Lan; Wu, Shuang; Wang, Hua; Zhao, Yong; Liao, Peng; Tian, Qing-Qing; Sun, Wen-Jian; Chen, Bo

2013-01-01

A novel rapid method for detection of the illicit beta2-agonist additives in health foods and traditional Chinese patent medicines was developed with the desorption corona beam ionization mass spectrometry (DCBI-MS) technique. The DCBI conditions including temperature and sample volume were optimized according to the resulting mass spectra intensity. Matrix effect on 9 beta2-agonists additives was not significant in the proposed rapid determination procedure. All of the 9 target molecules were detected within 1 min. Quantification was achieved based on the typical fragment ion in MS2 spectra of each analyte. The method showed good linear coefficients in the range of 1-100 mg x L(-1) for all analytes. The relative deviation values were between 14.29% and 25.13%. Ten claimed antitussive and antiasthmatic health foods and traditional Chinese patent medicines from local pharmacies were analyzed. All of them were negative with the proposed DCBI-MS method. Without tedious sample pretreatments, the developed DCBI-MS is simple, rapid and sensitive for rapid qualification and semi-quantification of the illicit beta2-agonist additives in health foods and traditional Chinese patent medicines.

Determination of oxygen in ternary uranium oxides by a gravimetric alkaline earth addition method

International Nuclear Information System (INIS)

Fujino, T.; Tagawa, H.

1979-01-01

The applicability of a gravimetric method based on alkaline earth metal addition for the determination of oxygen in ternary uranium oxides of the tupe M-U-O (M=La, Ce and Th) is described. The oxide sample is mixed with MgO or Basub(2.8)UOsub(5.8) and heated in air under suitable conditions. Because uranium is completely oxidized to the hexavalent state during the reaction, oxygen can be determined from the weight change. Oxygen in Lasub(y)Usub(1-y)Osub(2+x) is determined up to y = 0.8 with a standard deviation for x of +- 0.006 with MgO. For Thsub(y)Usub(1-y)Osub(2+x) the value of x is determined with Basub(2.8)UOsub(5.8) with a standard deviation of +- 0.01 at y = 0.8. For Cesub(y)Usub(1-y)Osub(2+x), the method can be applied only for low cerium concentrations where y = 0-0.2; the value for x with Basub(2.8)UOsub(5.8) at y = 0.2 showed a standard deviation of +- 0.002. (Auth.)

Introduction to First-Principles Electronic Structure Methods: Application to Actinide Materials

International Nuclear Information System (INIS)

Klepeis, J E

2005-01-01

The purpose of this paper is to provide an introduction for non-experts to first-principles electronic structure methods that are widely used in the field of condensed-matter physics, including applications to actinide materials. The methods I describe are based on density functional theory (DFT) within the local density approximation (LDA) and the generalized gradient approximation (GGA). In addition to explaining the meaning of this terminology I also describe the underlying theory itself in some detail in order to enable a better understanding of the relative strengths and weaknesses of the methods. I briefly mention some particular numerical implementations of DFT, including the linear muffin-tin orbital (LMTO), linear augmented plane wave (LAPW), and pseudopotential methods, as well as general methodologies that go beyond DFT and specifically address some of the weaknesses of the theory. The last third of the paper is devoted to a few selected applications that illustrate the ideas discussed in the first two-thirds. In particular, I conclude by addressing the current controversy regarding magnetic DFT calculations for actinide materials. Throughout this paper particular emphasis is placed on providing the appropriate background to enable the non-expert to gain a better appreciation of the application of first-principles electronic structure methods to the study of actinide and other materials

Influence of Sugars, Modified Starches and Hydrocolloids Addition on Colour and Thermal Properties of Raspberry Cream Fillings

Directory of Open Access Journals (Sweden)

Pichler Anita

2017-03-01

Full Text Available This paper deals with the influence of the addition of sugars (sucrose, fructose and trehalose, modified starches (tapioca or waxy maize starch and hydrocolloids (karaya or guar gum on colour and thermal properties of raspberry cream fillings. In addition, the influence of the above-mentioned additives on the colour and thermal properties of raspberry cream fillings stored at room temperature over a period of 8 and 16 months was investigated. Results showed that the highest anthocyanin content and total phenolic content were detected in raspberry cream filling prepared with sucrose and trehalose in combination with guar gum. During storage, after 8 and 16 months at room temperature, anthocyanin content and total phenolic content decreased. Results also showed that the kind of sugar and added modified starches or hydrocolloids influenced the thermal properties of cream fillings. During storage, a decrease was observed in both freezing temperature as well as enthalpy of cream fillings.

Weathering methods for preservative treated wood and their applicability for fire retarded wood

NARCIS (Netherlands)

Voss, A.

1999-01-01

preservative treated wood. The aim of the presentation is to inform you about current testing methods and to discuss their applicability to test fire retarded wood in outdoor use. Assuming that fire retardants will only be used in out of ground contact, only those methods are mentioned, which fit

Sampling method of environmental radioactivity monitoring

International Nuclear Information System (INIS)

1984-01-01

This manual provides sampling methods of environmental samples of airborne dust, precipitated dust, precipitated water (rain or snow), fresh water, soil, river sediment or lake sediment, discharged water from a nuclear facility, grains, tea, milk, pasture grass, limnetic organisms, daily diet, index organisms, sea water, marine sediment, marine organisms, and that for tritium and radioiodine determination for radiation monitoring from radioactive fallout or radioactivity release by nuclear facilities. This manual aims at the presentation of standard sampling procedures for environmental radioactivity monitoring regardless of monitoring objectives, and shows preservation method of environmental samples acquired at the samplingpoint for radiation counting for those except human body. Sampling techniques adopted in this manual is decided by the criteria that they are suitable for routine monitoring and any special skillfulness is not necessary. Based on the above-mentioned principle, this manual presents outline and aims of sampling, sampling position or object, sampling quantity, apparatus, equipment or vessel for sampling, sampling location, sampling procedures, pretreatment and preparation procedures of a sample for radiation counting, necessary recording items for sampling and sample transportation procedures. Special attention is described in the chapter of tritium and radioiodine because these radionuclides might be lost by the above-mentioned sample preservation method for radiation counting of less volatile radionuclides than tritium or radioiodine. (Takagi, S.)

Microwave Assisted Synthesis of ZnO Nanoparticles: Effect of Precursor Reagents, Temperature, Irradiation Time, and Additives on Nano-ZnO Morphology Development

Directory of Open Access Journals (Sweden)

Gastón P. Barreto

2013-01-01

Full Text Available The effect of different variables (precursor reagents, temperature, irradiation time, microwave radiation power, and additives addition on the final morphology of nano-ZnO obtained through the microwave assisted technique has been investigated. The characterization of the samples has been carried out by field emission scanning electron microscopy (FE-SEM in transmission mode, infrared (FTIR, UV-Vis spectroscopy, and powder X-ray diffraction (XRD. The results showed that all the above-mentioned variables influenced to some extent the shape and/or size of the synthetized nanoparticles. In particular, the addition of an anionic surfactant (sodium di-2-ethylhexyl-sulfosuccinate (AOT to the reaction mixture allowed the synthesis of smaller hexagonal prismatic particles (100 nm, which show a significant increase in UV absorption.

Effect of some addition agents on the electrodeposition of cadmium from acidic chloride baths

International Nuclear Information System (INIS)

Abd El-Halim, A.M.; Baghlaf, A.O.; Sobahi, M.I.

1984-01-01

A further development of a chloride-based cadmium plating bath containing 0.3 M CdCl 2 .(5/2)H 2 O, 0.1 M HCl, 0.4 M H 3 BO 3 and 2.0 M NH 4 Cl (bath I) is described. The influences of the individual addition agents thiourea, coumarin Ni 2+ ions and I - ions on the characteristics of cadmium electrodeposition from acidic chloride electrolytes containing 0.3 M CdCl 2 .(5/2)H 2 O, 0.1 M HCl, 0.4 M H 3 BO 3 , 2.0 M NH 4 Cl, 0.5 M sodium potassium tartrate and 5 g gelatin l -1 (bath II) were studied. Bath II including a combination of the four above-mentioned additives was denoted bath III. The additive-containing bath III produced a brighter but less hard cadmium deposit than the additive-free bath II. The individual effects of melamine, 3-methyl-4-p-methoxyphenylazopyrazol-5-one, dimethylformamide (DMF) and DMF with biacetyl-bis-(benzoylhydrazone) on the cathodic polarization and current efficiency of cadmium electrodeposition from baths II and III, as well as on the morphology and microhardness of the as-plated cadmium deposits, were investigated and discussed. (Auth.)

Comparison of artificial intelligence methods and empirical equations to estimate daily solar radiation

Science.gov (United States)

Mehdizadeh, Saeid; Behmanesh, Javad; Khalili, Keivan

2016-08-01

In the present research, three artificial intelligence methods including Gene Expression Programming (GEP), Artificial Neural Networks (ANN) and Adaptive Neuro-Fuzzy Inference System (ANFIS) as well as, 48 empirical equations (10, 12 and 26 equations were temperature-based, sunshine-based and meteorological parameters-based, respectively) were used to estimate daily solar radiation in Kerman, Iran in the period of 1992-2009. To develop the GEP, ANN and ANFIS models, depending on the used empirical equations, various combinations of minimum air temperature, maximum air temperature, mean air temperature, extraterrestrial radiation, actual sunshine duration, maximum possible sunshine duration, sunshine duration ratio, relative humidity and precipitation were considered as inputs in the mentioned intelligent methods. To compare the accuracy of empirical equations and intelligent models, root mean square error (RMSE), mean absolute error (MAE), mean absolute relative error (MARE) and determination coefficient (R2) indices were used. The results showed that in general, sunshine-based and meteorological parameters-based scenarios in ANN and ANFIS models presented high accuracy than mentioned empirical equations. Moreover, the most accurate method in the studied region was ANN11 scenario with five inputs. The values of RMSE, MAE, MARE and R2 indices for the mentioned model were 1.850 MJ m-2 day-1, 1.184 MJ m-2 day-1, 9.58% and 0.935, respectively.

Shape-control by microwave-assisted hydrothermal method for the synthesis of magnetite nanoparticles using organic additives

Energy Technology Data Exchange (ETDEWEB)

Rizzuti, Antonino [Politecnico di Bari, Dipartimento di Ingegneria Civile, Ambientale, del Territorio, Edile e di Chimica (Italy); Dassisti, Michele [Politecnico di Bari, Dipartimento di Meccanica, Management e Matematica (Italy); Mastrorilli, Piero, E-mail: p.mastrorilli@poliba.it [Politecnico di Bari, Dipartimento di Ingegneria Civile, Ambientale, del Territorio, Edile e di Chimica (Italy); Sportelli, Maria C.; Cioffi, Nicola; Picca, Rosaria A. [Università di Bari, Dipartimento di Chimica (Italy); Agostinelli, Elisabetta; Varvaro, Gaspare [Consiglio Nazionale delle Ricerche, Istituto di Struttura della Materia (Italy); Caliandro, Rocco [Consiglio Nazionale delle Ricerche, Istituto di Cristallografia (Italy)

2015-10-15

A simple and fast microwave-assisted hydrothermal method is proposed for the synthesis of magnetite nanoparticles. The addition of different surfactants (polyvinylpyrrolidone, oleic acid, or trisodium citrate) was studied to investigate the effect on size distribution, morphology, and functionalization of the magnetite nanoparticles. Microwave irradiation at 150 °C for 2 h of aqueous ferrous chloride and hydrazine without additives resulted in hexagonal magnetite nanoplatelets with a facet-to-facet distance of 116 nm and a thickness of 40 nm having a saturation magnetization of ∼65 Am{sup 2} kg{sup −1}. The use of polyvinylpyrrolidone led to hexagonal nanoparticles with a facet-to-facet distance of 120 nm and a thickness of 53 nm with a saturation magnetization of ∼54 Am{sup 2} kg{sup −1}. Additives such as oleic acid and trisodium citrate yielded quasi-spherical nanoparticles of 25 nm in size with a saturation magnetization of ∼70 Am{sup 2} kg{sup −1} and spheroidal nanoparticles of 60 nm in size with a saturation magnetization up to ∼82 Am{sup 2} kg{sup −1}, respectively. A kinetic control of the crystal growth is believed to be responsible for the hexagonal habit of the nanoparticles obtained without additive. Conversely, a thermodynamic control of the crystal growth, leading to spheroidal nanoparticles, seems to occur when additives which strongly interact with the nanoparticle surface are used. A thorough characterization of the materials was performed. Magnetic properties were investigated by Superconducting Quantum Interference Device and Vibrating Sample magnetometers. Based on the observed magnetic properties, the magnetite obtained using citrate appears to be a promising support for magnetically transportable catalysts.

Space-polarization Collaborative Suppression Method for Ionospheric Clutter in HFSWR

Directory of Open Access Journals (Sweden)

Yang Yunlong

2016-12-01

Full Text Available High Frequency Surface Wave Radar (HFSWR is able to receive surface target and low-flying aircraft echoes at a long-distance, but it suffers severely from ionospheric clutter. In this paper, a spacepolarization collaborative-based filter is introduced to mitigate ionospheric clutter. For parameter estimation on ionospheric clutter used for filters, a spatial parameter estimation algorithm based on compressive sensing is introduced to the DOA estimation of ionospheric clutter. In addition, a polarized parameter estimation algorithm based on statistical characteristics is proposed for ionospheric clutter in the range-Doppler spectrum. Higher estimation accuracy is achieved as a result of the range-Doppler spectrum; therefore, these two estimation algorithms enhance the performance of the space-polarization collaborative suppression method for ionospheric clutter. Experimental results of practical dual-polarized HFSWR data show the effectiveness of the two algorithms and the above mentioned filter for ionospheric clutter suppression.

Method of inserting fuel rod

International Nuclear Information System (INIS)

Kamimoto, Shuji; Imoo, Makoto; Tsuchida, Kenji.

1991-01-01

The present invention concerns a method of inserting a fuel rod upon automatic assembling, automatic dismantling and reassembling of a fuel assembly in a light water moderated reactor, as well as a device and components used therefor. That is, a fuel rod is inserted reliably to an aimed point of insertion by surrounding the periphery of the fuel rod to be inserted with guide rods, and thereby suppressing the movement of the fuel rod during insertion. Alternatively, a fuel rod is inserted reliably to a point of insertion by inserting guide rods at the periphery of the point of insertion for the fuel rod to be inserted thereby surrounding the point of insertion with the guide rods or fuel rods. By utilizing fuel rods already present in the fuel assembly as the guide rods described above, the fuel rod can be inserted reliably to the point of insertion with no additional devices. Dummy fuel rods are previously inserted in a fuel assembly which are then utilized as the above-mentioned guide rods to accurately insert the fuel rod to the point of insertion. (I.S.)

New Channel Coding Methods for Satellite Communication

Directory of Open Access Journals (Sweden)

J. Sebesta

2010-04-01

Full Text Available This paper deals with the new progressive channel coding methods for short message transmission via satellite transponder using predetermined length of frame. The key benefits of this contribution are modification and implementation of a new turbo code and utilization of unique features with applications of methods for bit error rate estimation and algorithm for output message reconstruction. The mentioned methods allow an error free communication with very low Eb/N0 ratio and they have been adopted for satellite communication, however they can be applied for other systems working with very low Eb/N0 ratio.

Iodine speciation in coastal and inland bathing waters and seaweeds extracts using a sequential injection standard addition flow-batch method.

Science.gov (United States)

Santos, Inês C; Mesquita, Raquel B R; Bordalo, Adriano A; Rangel, António O S S

2015-02-01

The present work describes the development of a sequential injection standard addition method for iodine speciation in bathing waters and seaweeds extracts without prior sample treatment. Iodine speciation was obtained by assessing the iodide and iodate content, the two inorganic forms of iodine in waters. For the determination of iodide, an iodide ion selective electrode (ISE) was used. The indirect determination of iodate was based on the spectrophotometric determination of nitrite (Griess reaction). For the iodate measurement, a mixing chamber was employed (flow batch approach) to explore the inherent efficient mixing, essential for the indirect determination of iodate. The application of the standard addition method enabled detection limits of 0.14 µM for iodide and 0.02 µM for iodate, together with the direct introduction of the target water samples, coastal and inland bathing waters. The results obtained were in agreement with those obtained by ICP-MS and a colorimetric reference procedure. Recovery tests also confirmed the accuracy of the developed method which was effectively applied to bathing waters and seaweed extracts. Copyright © 2014 Elsevier B.V. All rights reserved.

Classification of Actions or Inheritance also for Methods

DEFF Research Database (Denmark)

Kristensen, Bent Bruun; Madsen, Ole Lehrmann; Møller-Pedersen, Birger

1987-01-01

-class are specialized in sub-classes in a very primitive manner: they are simply re-defined and need not bear any resemblance of the virtual in the super-class. In BETA, a new object-oriented language, classes and methods are unified into one concept, and by an extension of the virtual concept, virtual procedures....../methods in sub-classes are defined as specializations of the virtuals in the super-class. The virtual procedures/methods of the sub-classes thus inherits the attributes (e.g. parameters) and actions from the “super-procedure/method”. In the languages mentioned above only procedures/methods may be virtual...

Fast analytical method for the addition of random variables

International Nuclear Information System (INIS)

Senna, V.; Milidiu, R.L.; Fleming, P.V.; Salles, M.R.; Oliveria, L.F.S.

1983-01-01

Using the minimal cut sets representation of a fault tree, a new approach to the method of moments is proposed in order to estimate confidence bounds to the top event probability. The method utilizes two or three moments either to fit a distribution (the normal and lognormal families) or to evaluate bounds from standard inequalities (e.g. Markov, Tchebycheff, etc.) Examples indicate that the results obtained by the log-normal family are in good agreement with those obtained by Monte Carlo simulation

Lactic Acid Fermentation, Urea and Lime Addition: Promising Faecal Sludge Sanitizing Methods for Emergency Sanitation.

Science.gov (United States)

Anderson, Catherine; Malambo, Dennis Hanjalika; Perez, Maria Eliette Gonzalez; Nobela, Happiness Ngwanamoseka; de Pooter, Lobke; Spit, Jan; Hooijmans, Christine Maria; de Vossenberg, Jack van; Greya, Wilson; Thole, Bernard; van Lier, Jules B; Brdjanovic, Damir

2015-10-29

In this research, three faecal sludge sanitizing methods-lactic acid fermentation, urea treatment and lime treatment-were studied for application in emergency situations. These methods were investigated by undertaking small scale field trials with pit latrine sludge in Blantyre, Malawi. Hydrated lime was able to reduce the E. coli count in the sludge to below the detectable limit within 1 h applying a pH > 11 (using a dosage from 7% to 17% w/w, depending faecal sludge alkalinity), urea treatment required about 4 days using 2.5% wet weight urea addition, and lactic acid fermentation needed approximately 1 week after being dosed with 10% wet weight molasses (2 g (glucose/fructose)/kg) and 10% wet weight pre-culture (99.8% pasteurised whole milk and 0.02% fermented milk drink containing Lactobacillus casei Shirota). Based on Malawian prices, the cost of sanitizing 1 m³ of faecal sludge was estimated to be €32 for lactic acid fermentation, €20 for urea treatment and €12 for hydrated lime treatment.

Theoretical aspects of new options of sublevel caving methods

Directory of Open Access Journals (Sweden)

Ladislav Kačmár

2008-12-01

Full Text Available The article deals with the proposal of the SMZ Jelšava a.s. exploitation issue. Author refers to possible options of the new methodsaplication, which rises of the theory of gravity flow loose and blasting rocks. With mentioned methods the safety of exploitation couldbe higher, especially in bigger depths.

Analysis of Vibration Diagnostics Methods for Induction Motors

Directory of Open Access Journals (Sweden)

A. P. Kalinov

2012-01-01

Full Text Available The paper presents an analysis of existing vibration diagnostics methods. In order to evaluate an efficiency of method application the following criteria have been proposed: volume of input data required for establishing diagnosis, data content, software and hardware level, execution time for vibration diagnostics. According to the mentioned criteria a classification of vibration diagnostics methods for determination of their advantages and disadvantages, search for their development and improvement has been presented in paper. The paper contains a comparative estimation of methods in accordance with the proposed  criteria. According to this estimation the most efficient methods are a spectral analysis and spectral analysis of the vibration signal envelope.

Pharmacovigilance from social media: mining adverse drug reaction mentions using sequence labeling with word embedding cluster features.

Science.gov (United States)

Nikfarjam, Azadeh; Sarker, Abeed; O'Connor, Karen; Ginn, Rachel; Gonzalez, Graciela

2015-05-01

Social media is becoming increasingly popular as a platform for sharing personal health-related information. This information can be utilized for public health monitoring tasks, particularly for pharmacovigilance, via the use of natural language processing (NLP) techniques. However, the language in social media is highly informal, and user-expressed medical concepts are often nontechnical, descriptive, and challenging to extract. There has been limited progress in addressing these challenges, and thus far, advanced machine learning-based NLP techniques have been underutilized. Our objective is to design a machine learning-based approach to extract mentions of adverse drug reactions (ADRs) from highly informal text in social media. We introduce ADRMine, a machine learning-based concept extraction system that uses conditional random fields (CRFs). ADRMine utilizes a variety of features, including a novel feature for modeling words' semantic similarities. The similarities are modeled by clustering words based on unsupervised, pretrained word representation vectors (embeddings) generated from unlabeled user posts in social media using a deep learning technique. ADRMine outperforms several strong baseline systems in the ADR extraction task by achieving an F-measure of 0.82. Feature analysis demonstrates that the proposed word cluster features significantly improve extraction performance. It is possible to extract complex medical concepts, with relatively high performance, from informal, user-generated content. Our approach is particularly scalable, suitable for social media mining, as it relies on large volumes of unlabeled data, thus diminishing the need for large, annotated training data sets. © The Author 2015. Published by Oxford University Press on behalf of the American Medical Informatics Association.

Performance of the Tariff Method: validation of a simple additive algorithm for analysis of verbal autopsies

Directory of Open Access Journals (Sweden)

Murray Christopher JL

2011-08-01

Full Text Available Abstract Background Verbal autopsies provide valuable information for studying mortality patterns in populations that lack reliable vital registration data. Methods for transforming verbal autopsy results into meaningful information for health workers and policymakers, however, are often costly or complicated to use. We present a simple additive algorithm, the Tariff Method (termed Tariff, which can be used for assigning individual cause of death and for determining cause-specific mortality fractions (CSMFs from verbal autopsy data. Methods Tariff calculates a score, or "tariff," for each cause, for each sign/symptom, across a pool of validated verbal autopsy data. The tariffs are summed for a given response pattern in a verbal autopsy, and this sum (score provides the basis for predicting the cause of death in a dataset. We implemented this algorithm and evaluated the method's predictive ability, both in terms of chance-corrected concordance at the individual cause assignment level and in terms of CSMF accuracy at the population level. The analysis was conducted separately for adult, child, and neonatal verbal autopsies across 500 pairs of train-test validation verbal autopsy data. Results Tariff is capable of outperforming physician-certified verbal autopsy in most cases. In terms of chance-corrected concordance, the method achieves 44.5% in adults, 39% in children, and 23.9% in neonates. CSMF accuracy was 0.745 in adults, 0.709 in children, and 0.679 in neonates. Conclusions Verbal autopsies can be an efficient means of obtaining cause of death data, and Tariff provides an intuitive, reliable method for generating individual cause assignment and CSMFs. The method is transparent and flexible and can be readily implemented by users without training in statistics or computer science.

ADSORPTION METHOD FOR SEPARATING METAL CATIONS

Science.gov (United States)

Khym, J.X.

1959-03-10

The chromatographic separation of fission product cations is discussed. By use of this method a mixture of metal cations containing Zr, Cb, Ce, Y, Ba, and Sr may be separated from one another. Mentioned as preferred exchange adsorbents are resins containing free sulfonic acid groups. Various eluants, such as tartaric acid, HCl, and citric acid, used at various acidities, are employed to effect the selective elution and separation of the various fission product cations.

The Use of Some Forecasting Methods and SWOT Analysis in the Selected Processes of Foundry

Directory of Open Access Journals (Sweden)

Szymszal J.

2017-12-01

Full Text Available Forecasting and analysis SWOT are helping tools in the business activity, because under conditions of dynamic changes in both closer and more distant surroundings, reliable, forward-looking information and trends analysis are playing a decisive role. At present, the ability to use available data in forecasting and other analyzes according with changes in business environment are the key managerial skills required, since both forecasting and SWOT analysis are a integral part of the management process, and the appropriate level of forecasting knowledge is increasingly appreciated. Examples of practical use of some forecasting methods in optimization of the procurement, production and distribution processes in foundries are given. The possibilities of using conventional quantitative forecasting methods based on econometric and adaptive models applying the creep trend and harmonic weights are presented. The econometric models were additionally supplemented with the presentation of error estimation methodology, quality assessment and statistical verification of the forecast. The possibility of using qualitative forecasts based on SWOT analysis was also mentioned.

Additive conjoint measurement for multiattribute utility

NARCIS (Netherlands)

Maas, A.; Wakker, P.P.

1994-01-01

This paper shows that multiattribute utility can be simplified by methods from additive conjoint measurement. Given additive conjoint measurability under certainty, axiomatizations can be simplified, and implementation and reliability of elicitation can be improved. This also contributes to the

Methods and energy storage devices utilizing electrolytes having surface-smoothing additives

Science.gov (United States)

Xu, Wu; Zhang, Jiguang; Graff, Gordon L; Chen, Xilin; Ding, Fei

2015-11-12

Electrodeposition and energy storage devices utilizing an electrolyte having a surface-smoothing additive can result in self-healing, instead of self-amplification, of initial protuberant tips that give rise to roughness and/or dendrite formation on the substrate and anode surface. For electrodeposition of a first metal (M1) on a substrate or anode from one or more cations of M1 in an electrolyte solution, the electrolyte solution is characterized by a surface-smoothing additive containing cations of a second metal (M2), wherein cations of M2 have an effective electrochemical reduction potential in the solution lower than that of the cations of M1.

E-LEARNING METHOD APPLIED TO TECHNICAL GRAPHICS SUBJECTS

Directory of Open Access Journals (Sweden)

GOANTA Adrian Mihai

2011-11-01

Full Text Available The paper presents some of the author’s endeavors in creating video courses for the students from the Faculty of Engineering in Braila related to subjects involving technical graphics . There are also mentioned the steps taken in completing the method and how to achieve a feedback on the rate of access to these types of courses by the students.

Integral methods of solving boundary-value problems of nonstationary heat conduction and their comparative analysis

Science.gov (United States)

Kot, V. A.

2017-11-01

The modern state of approximate integral methods used in applications, where the processes of heat conduction and heat and mass transfer are of first importance, is considered. Integral methods have found a wide utility in different fields of knowledge: problems of heat conduction with different heat-exchange conditions, simulation of thermal protection, Stefantype problems, microwave heating of a substance, problems on a boundary layer, simulation of a fluid flow in a channel, thermal explosion, laser and plasma treatment of materials, simulation of the formation and melting of ice, inverse heat problems, temperature and thermal definition of nanoparticles and nanoliquids, and others. Moreover, polynomial solutions are of interest because the determination of a temperature (concentration) field is an intermediate stage in the mathematical description of any other process. The following main methods were investigated on the basis of the error norms: the Tsoi and Postol’nik methods, the method of integral relations, the Gudman integral method of heat balance, the improved Volkov integral method, the matched integral method, the modified Hristov method, the Mayer integral method, the Kudinov method of additional boundary conditions, the Fedorov boundary method, the method of weighted temperature function, the integral method of boundary characteristics. It was established that the two last-mentioned methods are characterized by high convergence and frequently give solutions whose accuracy is not worse that the accuracy of numerical solutions.

Development and validation of new spectrophotometric ratio H-point standard addition method and application to gastrointestinal acting drugs mixtures

Science.gov (United States)

Yehia, Ali M.

2013-05-01

New, simple, specific, accurate and precise spectrophotometric technique utilizing ratio spectra is developed for simultaneous determination of two different binary mixtures. The developed ratio H-point standard addition method (RHPSAM) was managed successfully to resolve the spectral overlap in itopride hydrochloride (ITO) and pantoprazole sodium (PAN) binary mixture, as well as, mosapride citrate (MOS) and PAN binary mixture. The theoretical background and advantages of the newly proposed method are presented. The calibration curves are linear over the concentration range of 5-60 μg/mL, 5-40 μg/mL and 4-24 μg/mL for ITO, MOS and PAN, respectively. Specificity of the method was investigated and relative standard deviations were less than 1.5. The accuracy, precision and repeatability were also investigated for the proposed method according to ICH guidelines.

Notion and methods of measurement of enterprise financial liquidity

Directory of Open Access Journals (Sweden)

Zbigniew Gołaś

2010-01-01

Full Text Available The article shows methods of assessment of the financial liquidity of an enterprise. Static, dynamic and non-classic methods of the financial liquidity assessment have been shown. The following static methods are discussed: construction and information content of current indicator, rapid indicator and indicator of an instant liquidity. In the case of dynamic part, indicators were shown of cash efficiency and sufficiency i.e. criteria of financial liquidity assessing based on the financial circulations. Moreover, chosen methods were mentioned of the financial liquidity assessment, which are less frequently used in practice, which are called non-classic.

A brief introduction to computer-intensive methods, with a view towards applications in spatial statistics and stereology.

Science.gov (United States)

Mattfeldt, Torsten

2011-04-01

Computer-intensive methods may be defined as data analytical procedures involving a huge number of highly repetitive computations. We mention resampling methods with replacement (bootstrap methods), resampling methods without replacement (randomization tests) and simulation methods. The resampling methods are based on simple and robust principles and are largely free from distributional assumptions. Bootstrap methods may be used to compute confidence intervals for a scalar model parameter and for summary statistics from replicated planar point patterns, and for significance tests. For some simple models of planar point processes, point patterns can be simulated by elementary Monte Carlo methods. The simulation of models with more complex interaction properties usually requires more advanced computing methods. In this context, we mention simulation of Gibbs processes with Markov chain Monte Carlo methods using the Metropolis-Hastings algorithm. An alternative to simulations on the basis of a parametric model consists of stochastic reconstruction methods. The basic ideas behind the methods are briefly reviewed and illustrated by simple worked examples in order to encourage novices in the field to use computer-intensive methods. © 2010 The Authors Journal of Microscopy © 2010 Royal Microscopical Society.

Synthesis of Nickel (Ni) Doped HKUST-1 Using Solvotermal Method with Addition of Acetic Acid as Modulator

OpenAIRE

Safii, Farhan Fikri; Ediati, Ratna

2015-01-01

Hong Kong University of Science and Technology-1 (HKUST-1) is metal organic framework (MOF) that composed from ligand BTC (1,3,5-benzene tricarboxylic) and copper ions. The method used in this study is solvotermal with variations nickel ion doping and additions acetic acid as modulator. The purpose of this study is to increase the hydrogen storage capacity. The results obtained were characterized by XRD showed that the HKUST-1 and Ni-HKUST-1 has formed, showed by peaks at 2 theta = 6.7, 9.5, ...

Food additives and preschool children.

Science.gov (United States)

Martyn, Danika M; McNulty, Breige A; Nugent, Anne P; Gibney, Michael J

2013-02-01

Food additives have been used throughout history to perform specific functions in foods. A comprehensive framework of legislation is in place within Europe to control the use of additives in the food supply and ensure they pose no risk to human health. Further to this, exposure assessments are regularly carried out to monitor population intakes and verify that intakes are not above acceptable levels (acceptable daily intakes). Young children may have a higher dietary exposure to chemicals than adults due to a combination of rapid growth rates and distinct food intake patterns. For this reason, exposure assessments are particularly important in this age group. The paper will review the use of additives and exposure assessment methods and examine factors that affect dietary exposure by young children. One of the most widely investigated unfavourable health effects associated with food additive intake in preschool-aged children are suggested adverse behavioural effects. Research that has examined this relationship has reported a variety of responses, with many noting an increase in hyperactivity as reported by parents but not when assessed using objective examiners. This review has examined the experimental approaches used in such studies and suggests that efforts are needed to standardise objective methods of measuring behaviour in preschool children. Further to this, a more holistic approach to examining food additive intakes by preschool children is advisable, where overall exposure is considered rather than focusing solely on behavioural effects and possibly examining intakes of food additives other than food colours.

Decomposing method for ion exchange resin

International Nuclear Information System (INIS)

Sako, Takeshi; Sato, Shinshi; Akai, Yoshie; Moniwa, Shinobu; Yamada, Kazuo

1998-01-01

The present invention concerns a method of decomposing ion exchange resins generated in a nuclear power plant to carbon dioxide reliably in a short period of time. (1) The ion exchange resins are mixed with water, and then they are kept for a predetermined period of time in the presence of an inert gas at high temperature and high pressure exceeding the critical point of water to decompose the ion exchange resins. (2) The ion exchange resins is mixed with water, an oxidant is added and they are kept for a predetermined time in the presence of an inert gas at a high temperature and a high pressure exceeding a critical point of water of an inert gas at a high temperature to decompose the ion exchange resins. (3) An alkali or acid is added to ion exchange resins and water to control the hydrogen ion concentration in the solution and the ion exchange resins are decomposed in above-mentioned (1) or (2). Sodium hydroxide is used as the alkali and hydrochloric acid is used as the acid. In addition, oxygen, hydrogen peroxide or ozone is used as an oxidant. (I.S.)

A tale of two tools: Reliability and feasibility of social media measurement tools examining e-cigarette twitter mentions

Directory of Open Access Journals (Sweden)

Amelia Burke-Garcia

Full Text Available Given 70% of Americans are seeking health information online, social media are becoming main sources of health-related information and discussions. Specifically, compounding rising trends in use of e-cigarettes in the US, there has been a rapid rise in e-cigarette marketing – much of which is happening on social media. Public health professionals seeking to understand consumer knowledge, attitudes and beliefs about e-cigarettes should consider analyzing social media data and to do so, there are numerous free and paid tools available. However, each uses different sources and processes, which makes data validation challenging. This exploratory study sought to understand the reliability and feasibility of two social media data tools analyzing e-cigarette tweets. Twitter mentions were pulled from two different industry standard tools (GNIP and Radian6 and data were evaluated on six measures, e.g. Cost, Feasibility, Ease of Use, Poster Type (individual/organization, Context (tweet content analysis, and Valence (positive/negative. Findings included similarities amongst the data sets in terms of the content themes but differences in cost and ease of use of the tools themselves. These findings align with prior research, notably that e-cigarette marketing tweets are most common and public health-related content is noticeably absent. Findings from this exploratory study can inform future social media studies as well as communication campaigns seeking to address the emerging issue of e-cigarette use. Keywords: E-cigarettes, Vaping, Twitter, Tweets, Social media

Method for assessment of stormwater treatment facilities - Synthetic road runoff addition including micro-pollutants and tracer.

Science.gov (United States)

Cederkvist, Karin; Jensen, Marina B; Holm, Peter E

2017-08-01

Stormwater treatment facilities (STFs) are becoming increasingly widespread but knowledge on their performance is limited. This is due to difficulties in obtaining representative samples during storm events and documenting removal of the broad range of contaminants found in stormwater runoff. This paper presents a method to evaluate STFs by addition of synthetic runoff with representative concentrations of contaminant species, including the use of tracer for correction of removal rates for losses not caused by the STF. A list of organic and inorganic contaminant species, including trace elements representative of runoff from roads is suggested, as well as relevant concentration ranges. The method was used for adding contaminants to three different STFs including a curbstone extension with filter soil, a dual porosity filter, and six different permeable pavements. Evaluation of the method showed that it is possible to add a well-defined mixture of contaminants despite different field conditions by having a flexibly system, mixing different stock-solutions on site, and use bromide tracer for correction of outlet concentrations. Bromide recovery ranged from only 12% in one of the permeable pavements to 97% in the dual porosity filter, stressing the importance of including a conservative tracer for correction of contaminant retention values. The method is considered useful in future treatment performance testing of STFs. The observed performance of the STFs is presented in coming papers. Copyright © 2017 Elsevier Ltd. All rights reserved.

Proposal of Evolutionary Simplex Method for Global Optimization Problem

Science.gov (United States)

Shimizu, Yoshiaki

To make an agile decision in a rational manner, role of optimization engineering has been notified increasingly under diversified customer demand. With this point of view, in this paper, we have proposed a new evolutionary method serving as an optimization technique in the paradigm of optimization engineering. The developed method has prospects to solve globally various complicated problem appearing in real world applications. It is evolved from the conventional method known as Nelder and Mead’s Simplex method by virtue of idea borrowed from recent meta-heuristic method such as PSO. Mentioning an algorithm to handle linear inequality constraints effectively, we have validated effectiveness of the proposed method through comparison with other methods using several benchmark problems.

Additive theory of prime numbers

CERN Document Server

Hua, L K

2009-01-01

Loo-Keng Hua was a master mathematician, best known for his work using analytic methods in number theory. In particular, Hua is remembered for his contributions to Waring's Problem and his estimates of trigonometric sums. Additive Theory of Prime Numbers is an exposition of the classic methods as well as Hua's own techniques, many of which have now also become classic. An essential starting point is Vinogradov's mean-value theorem for trigonometric sums, which Hua usefully rephrases and improves. Hua states a generalized version of the Waring-Goldbach problem and gives asymptotic formulas for the number of solutions in Waring's Problem when the monomial x^k is replaced by an arbitrary polynomial of degree k. The book is an excellent entry point for readers interested in additive number theory. It will also be of value to those interested in the development of the now classic methods of the subject.

Assessment on the methods of measuring the tyre-road contact patch stresses

Science.gov (United States)

Anghelache, G.; Moisescu, A.-R.; Buretea, D.

2017-08-01

The paper reviews established and modern methods for investigating tri-axial stress distributions in the tyre-road contact patch. The authors used three methods of measuring stress distributions: strain gauge method; force sensing technique; acceleration measurements. Four prototypes of instrumented pins transducers involving mentioned measuring methods were developed. Data acquisitions of the contact patch stresses distributions were performed using each transducer with instrumented pin. The results are analysed and compared, underlining the advantages and drawbacks of each method. The experimental results indicate that the three methods are valuable.

Development of computational methods of design by analysis for pressure vessel components

International Nuclear Information System (INIS)

Bao Shiyi; Zhou Yu; He Shuyan; Wu Honglin

2005-01-01

Stress classification is not only one of key steps when pressure vessel component is designed by analysis, but also a difficulty which puzzles engineers and designers at all times. At present, for calculating and categorizing the stress field of pressure vessel components, there are several computation methods of design by analysis such as Stress Equivalent Linearization, Two-Step Approach, Primary Structure method, Elastic Compensation method, GLOSS R-Node method and so on, that are developed and applied. Moreover, ASME code also gives an inelastic method of design by analysis for limiting gross plastic deformation only. When pressure vessel components design by analysis, sometimes there are huge differences between the calculating results for using different calculating and analysis methods mentioned above. As consequence, this is the main reason that affects wide application of design by analysis approach. Recently, a new approach, presented in the new proposal of a European Standard, CEN's unfired pressure vessel standard EN 13445-3, tries to avoid problems of stress classification by analyzing pressure vessel structure's various failure mechanisms directly based on elastic-plastic theory. In this paper, some stress classification methods mentioned above, are described briefly. And the computational methods cited in the European pressure vessel standard, such as Deviatoric Map, and nonlinear analysis methods (plastic analysis and limit analysis), are depicted compendiously. Furthermore, the characteristics of computational methods of design by analysis are summarized for selecting the proper computational method when design pressure vessel component by analysis. (authors)

Contribution to determination of coal grindability using Hardgrove method

OpenAIRE

Tichánek, František

2008-01-01

The paper deals with determination of grindability of coal using Hardgrove method. Some non-availabilities of determination are mentioned as well as factors affecting grindability and relations for conversion of Hardgrove Grindability Index (HGI) values to Bond Work Index (Wi). Paper also provides information on utilization of Hardgrove method in Czech Republic and indicates HGI values for coal from OKD-Karvina region. Příspěvek se zabývá stanovením melitelnosti uhlí pomocí metody Hardgrov...

"A Comparison of Several Methods in a Rock Slope Stability ...

African Journals Online (AJOL)

This researchuses the mentioned methods and principles in the stability analysis of some rock slopes in an open pit mine in Syria, that is Khneifees phosphate mine. The importance of this researchis that it shows the role of kinematical analysis in minimizing efforts when verifying the safety of rock slopes in site, and when ...

On the rate of convergence of the alternating projection method in finite dimensional spaces

Science.gov (United States)

Galántai, A.

2005-10-01

Using the results of Smith, Solmon, and Wagner [K. Smith, D. Solomon, S. Wagner, Practical and mathematical aspects of the problem of reconstructing objects from radiographs, Bull. Amer. Math. Soc. 83 (1977) 1227-1270] and Nelson and Neumann [S. Nelson, M. Neumann, Generalizations of the projection method with application to SOR theory for Hermitian positive semidefinite linear systems, Numer. Math. 51 (1987) 123-141] we derive new estimates for the speed of the alternating projection method and its relaxed version in . These estimates can be computed in at most O(m3) arithmetic operations unlike the estimates in papers mentioned above that require spectral information. The new and old estimates are equivalent in many practical cases. In cases when the new estimates are weaker, the numerical testing indicates that they approximate the original bounds in papers mentioned above quite well.

Acceleration methods and models in Sn calculations

International Nuclear Information System (INIS)

Sbaffoni, M.M.; Abbate, M.J.

1984-01-01

In some neutron transport problems solved by the discrete ordinate method, it is relatively common to observe some particularities as, for example, negative fluxes generation, slow and insecure convergences and solution instabilities. The commonly used models for neutron flux calculation and acceleration methods included in the most used codes were analyzed, in face of their use in problems characterized by a strong upscattering effect. Some special conclusions derived from this analysis are presented as well as a new method to perform the upscattering scaling for solving the before mentioned problems in this kind of cases. This method has been included in the DOT3.5 code (two dimensional discrete ordinates radiation transport code) generating a new version of wider application. (Author) [es

Methods for determining radionuclide retardation factors: status report

International Nuclear Information System (INIS)

Relyea, J.F.; Serne, R.J.; Rai, D.

1980-04-01

This report identifies a number of mechanisms that retard radionuclide migration, and describes the static and dynamic methods that are used to study such retardation phenomena. Both static and dynamic methods are needed for reliable safety assessments of underground nuclear-waste repositories. This report also evaluates the extent to which the two methods may be used to diagnose radionuclide migration through various types of geologic media, among them unconsolidated, crushed, intact, and fractured rocks. Adsorption is one mechanism that can control radionuclide concentrations in solution and therefore impede radionuclide migration. Other mechanisms that control a solution's radionuclide concentration and radionuclide migration are precipitation of hydroxides and oxides, oxidation-reduction reactions, and the formation of minerals that might include the radionuclide as a structural element. The retardation mechanisms mentioned above are controlled by such factors as surface area, cation exchange capacity, solution pH, chemical composition of the rock and of the solution, oxidation-reduction potential, and radionuclide concentration. Rocks and ground waters used in determining retardation factors should represent the expected equilibrium conditions in the geologic system under investigation. Static test methods can be used to rapidly screen the effects of the factors mentioned above. Dynamic (or column) testing, is needed to assess the effects of hydrodynamics and the interaction of hydrodynamics with the other important parameters. This paper proposes both a standard method for conducting batch Kd determinations, and a standard format for organizing and reporting data. Dynamic testing methods are not presently developed to the point that a standard methodology can be proposed. Normal procedures are outlined for column experimentation and the data that are needed to analyze a column experiment are identified

Comparing the Validity of Non-Invasive Methods in Measuring Thoracic Kyphosis and Lumbar Lordosis

Directory of Open Access Journals (Sweden)

Mohammad Yousefi

2012-04-01

Full Text Available Background: the purpose of this article is to study the validity of each of the non-invasive methods (flexible ruler, spinal mouse, and processing the image versus the one through-Ray radiation (the basic method and comparing them with each other.Materials and Methods: for evaluating the validity of each of these non-invasive methods, the thoracic Kyphosis and lumber Lordosis angle of 20 students of Birjand University (age mean and standard deviation: 26±2, weight: 72±2.5 kg, height: 169±5.5 cm through fours methods of flexible ruler, spinal mouse, and image processing and X-ray.Results: the results indicated that the validity of the methods including flexible ruler, spinal mouse, and image processing in measuring the thoracic Kyphosis and lumber Lordosis angle respectively have an adherence of 0.81, 0.87, 0.73, 0.76, 0.83, 0.89 (p>0.05. As a result, regarding the gained validity against the golden method of X-ray, it could be stated that the three mentioned non-invasive methods have adequate validity. In addition, the one-way analysis of variance test indicated that there existed a meaningful relationship between the three methods of measuring the thoracic Kyphosis and lumber Lordosis, and with respect to the Tukey’s test result, the image processing method is the most precise one.Conclusion as a result, this method could be used along with other non-invasive methods as a valid measuring method.

Determination of photooxygenation products of rotenone with isotope dilution method

International Nuclear Information System (INIS)

Chubachi, Mitsuo; Hamada, Masayuki

1975-01-01

When rotenone dissolved in certain solvent was photochemically oxidized, rotenolones, dehydrorotenone and rotenonone were obtained as main products. In order to determine the quantitative yields of these compounds in photooxygenation products, four compounds mentioned above were labeled with carbon-14 and the isotope dilution method by these labeled compounds was applied to the product analysis. (auth.)

RE-EDUCATIVE METHOD IN THE PROCESS OF MINIMIZING OF AUTOAGRESIVE WAYS OF BEHAVIOR

Directory of Open Access Journals (Sweden)

Nenad GLUMBIC

1999-05-01

Full Text Available Autoagressive behavior is a relatively frequent symptom of mental disturbances and behavior disturbances which are the subject of professional engagement of clinically oriented defectologists. In the process of rehabilitation numerous methods are used, from behavioral to psychopharmacological ones by which the above mentioned problems are eliminated of softened.The paper deals with four children with different diagnosis (autism, disintegrative psychosis, Patau syndrome and amaurosis that have the same common denominator-mental retardation and autoagression.We have tried to point out-by the description of a study case as well as the ways od work with these children-an application possibly of the particular methods of general and special re-education of psychomotorics in the process of autoagressive ways of behavior minimizing.The paper gives the autor’s notion of indications for re-educative method application with in the multihandicapped children population. Defectological treatment discovers new forms of existence in the existential field, not only to the retarded child but also to the very therapist. Epistemological consequences of the mentioned transfer are given in details in the paper.

A novel method combining additive manufacturing and alloy infiltration for NdFeB bonded magnet fabrication

Science.gov (United States)

Li, Ling; Tirado, Angelica; Conner, B. S.; Chi, Miaofang; Elliott, Amy M.; Rios, Orlando; Zhou, Haidong; Paranthaman, M. Parans

2017-09-01

In this paper, binder jetting additive manufacturing technique is employed to fabricate NdFeB isotropic bonded magnets, followed by an infiltration process with low-melting point eutectic alloys [i.e., Nd3Cu0.25Co0.75 (NdCuCo) and Pr3Cu0.25Co0.75 (PrCuCo)]. Densification and mechanical strength improvement are achieved for the as-printed porous part. Meanwhile, the intrinsic coercivity Hci is enhanced from 732 to 1345 kA/m and 1233 kA/m after diffusion of NdCuCo and PrCuCo, respectively. This study presents a novel method for fabricating complex-shaped bonded magnets with promising mechanical and magnetic properties.

Stable solidification of cesium with an allophane additive by a pressing/sintering method

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiaoxia [School of Nuclear Science and Engineering, Shanghai Jiao Tong University, Shanghai, 200240 (China); Wu, Yan, E-mail: wu_yan@sjtu.edu.cn [School of Nuclear Science and Engineering, Shanghai Jiao Tong University, Shanghai, 200240 (China); Wei, Yuezhou [School of Nuclear Science and Engineering, Shanghai Jiao Tong University, Shanghai, 200240 (China); College of Resources and Metallurgy, Guangxi University, Nanning, 530004 (China); Mimura, Hitoshi; Matsukura, Minoru [UNION SHOWA K.K., 1-8-40Kounan Minato-ku, Tokyo, 108-0075 (Japan)

2017-03-15

Pyrolysis of AMP/SiO{sub 2} adsorbed Cs (AMP-Cs/SiO{sub 2}) occurred at > 400 °C sintering temperature, and Cs immobilisation decreased from 100% to 40% after sintering at 1200 °C. To safely dispose radioactive Cs, allophane was immobilized with AMP-Cs/SiO{sub 2} to prepare a stable form by using a pressing/sintering method. The structure of AMP-Cs/SiO{sub 2} collapsed, and cesium aluminosilicate formed more easily under conditions of higher sintering temperature (>800 °C) or increasing mixing ratio of allophane (mass ratio = 1:3 AMP-Cs/SiO{sub 2}-allophane). The decomposition products of AMP-Cs/SiO{sub 2} were Cs{sub 2}O, MoO{sub 3} and P{sub 2}O{sub 5} at 1200 °C. Cs{sub 2}O volatilisation was depressed by allophane addition, and a stable immobilisation phase of Cs{sub 4}Al{sub 4}Si{sub 20}O{sub 48} formed. An immobilisation ratio of Cs of approximately 100% was maintained. The leachability of Cs for AMP-Cs/SiO{sub 2}-allophane (1:3, 1200 °C) in distilled water at 25 °C and 90 °C for 15 days was estimated as 0.174% and 1.55%, respectively. - Highlights: • A pressing/sintering method was used to solidify AMP-Cs/SiO{sub 2}-allophane. • The volatility of Cs{sub 2}O could be effectively restrained by allophane. • Cs{sub 4}Al{sub 4}Si{sub 20}O{sub 48} was formed for stable solidification of Cs. • The leachability of Cs from sintered AMP-Cs/SiO{sub 2}-allophane was relatively low.

Applications of the Monte Carlo method in radiation protection

International Nuclear Information System (INIS)

Kulkarni, R.N.; Prasad, M.A.

1999-01-01

This paper gives a brief introduction to the application of the Monte Carlo method in radiation protection. It may be noted that an exhaustive review has not been attempted. The special advantage of the Monte Carlo method has been first brought out. The fundamentals of the Monte Carlo method have next been explained in brief, with special reference to two applications in radiation protection. Some sample current applications have been reported in the end in brief as examples. They are, medical radiation physics, microdosimetry, calculations of thermoluminescence intensity and probabilistic safety analysis. The limitations of the Monte Carlo method have also been mentioned in passing. (author)

Radioisotope methods for leucocyte labelling

International Nuclear Information System (INIS)

Kostadinova, I.; Kovacheva, S.

1988-01-01

A review is made of the labelling methods with the following tracers: 3 H-thymidine, 32 P-DP, 111 In (oxine, tropolon, acetylacetone, MERC), 99m Tc (reduced 99m Tc, lypophyl 99m Tc-complexes and 99m Tc-colloids). The main diagnosis areas are mentioned: abdominal abscesses and inflammations, inflammation foci of skeleton or of implanted prosthesis; acute myocardial infarction, bacterial endocarditis, rejection of kydney transplantations or vascular grafts. It is concluded that labelled leucocytes are very reliable for noninvasive diagnosis of inflammation foci with unclear localization

Observation of the Effectiveness of Drama Method in Helping to Acquire the Addition-Subtraction Skills by Children at Preschool Phase

Science.gov (United States)

Soydan, Sema; Quadir, Seher Ersoy

2013-01-01

Principal aim of this study is to show the effectiveness of the program prepared by researchers in order to enable 6 year-old children attending pre-school educational institutions to effectively gain addition subtraction skills through a drama-related method. The work group in the research comprised of 80 kids who continued their education in…

Effect of heat absorbing powder addition on cell morphology of porous titanium composite manufactured by reactive precursor method

International Nuclear Information System (INIS)

Kobashi, Makoto; Kamiya, Yoshinori; Kanetake, Naoyuki

2012-01-01

Open-cell structured porous titanium/ceramics composite was synthesized by a reactive precursor method using titanium and boron carbide (B 4 C) as reactant powders. Pore morphology was controlled by adding heat absorbing powder (titanium diboride: TiB 2 ) in the Ti+B 4 C blended powder. The effects of molar blending ratio of titanium and B 4 C and the amount of heat absorbing powder addition on the cell morphology (either open or closed) were investigated. Fine and homogeneous open-cell structure was achieved by adding appropriate amount of heat absorbing agent powder (>15 vol%), and the relative density of the specimen after the reaction became closer to that of the precursor by increasing TiB 2 volume fraction. When the volume fraction of TiB 2 addition was 20%, the open-cell fraction was maintained as 1.0 regardless of the relative density of the precursor.

Effect of Additives on the Physicochemical and Drug Release ...

African Journals Online (AJOL)

Purpose: To prepare and evaluate spherical agglomerates of pioglitazone hydrochloride (PGH) for direct compression with different additives. Method: Spherical agglomerates of pioglitazone hydrochloride were prepared by emulsion solvent diffusion method with and without additives (polyethylene glycol 6000, polyvinyl ...

Seismic response of structures by the response spectrum method

International Nuclear Information System (INIS)

Hadjian, A.H.

1981-01-01

The problems of the acceleration profile at the lower elevations of cantilever structures and the response of relatively rigid structures are explored. It is shown that the use of the conventional methods for the above problems provide very approximate results. An alternate combination of the modal responses is proposed that not only resolves the above problems but also provides better estimates of response for the complete range of structure frequencies. The procedure treats the relative and rigid body responses separately and then appropriately combines the two results. For the rigid range of frequencies (fundamental frequencies greater than about 2 Hz), the proposed procedure does not encounter any numerical difficulties because of the additive nature of the component responses; however, the application of the proposed procedure for very flexible structures causes accuracy problems since the rigid body effects tend to be subtractive from the flexural response of about equal magnitude. For this latter class of problems, the conventional approach of modal combination provides adequate results and avoids the above mentioned numerical difficulties. (orig.)

A review of experiment data processing method for uranium mining and metallurgy in BRICEM

International Nuclear Information System (INIS)

Ye Guoqiang; Lu Kehong; Wang Congying

1997-01-01

The authors investigates the methods of experiment data processing in Beijing Research Institute of Chemical Engineering and Metallurgy (BRICEM). It turns out that error analysis method is used to process experiment data, single-factor transformation and orthogonal test design method are adopted for arranging test, and regression analysis and mathematical process simulation are applied to process mathematical model for uranium mining and metallurgy. The methods above-mentioned lay a foundation for the utilization of mathematical statistics in our subject

Isobolographic Analysis for Additive, Synergism and Antagonism Effects in Binary Mixture of Mesosulfuron + Iodosulfuron and Clodinafop-Propargyl

Directory of Open Access Journals (Sweden)

A. A Chitband

2012-07-01

Full Text Available The reduction of herbicide applications is a main research priority in recent years for herbicide reducing the risk of side-effects and costs from herbicides. Therefore To predicting additive, synergism or antagonism effects mesosulfuron + iodosulfuron and clodinafop-propargyl two herbicides mixture on wild oat with isobole curvatures, greenhouse experimental in completely randomized design with 36 treatments (in dose-response arrangements and four replicates for each experiment treatments were conducted at Ferdowsi University of Mashhad. Treatments included mesosulfuron + iodosulfuron alone at doses of 0 , 2.4, 6, 12, 18 and 24 g ai ha-1, clodinafop alone at doses of 0, 6.4, 16, 32, 48 and 64 g ai ha-1 and six mixtures ratio of doses of two herbicides above mentioned as 100:0%,75:25%, 50:50%, 25:75% , 10:90% and 0:100%. The results showed mesosulfuron + iodosulfuron and clodinafop-propargyl at high dose rates showed complete control of wild oat. In addition Concentration Addition (CA model describe Fitted the data better than Hewlett and Voelund models. On the other hand, herbicides combination with each other showed additive effects on wild oat control, As by increasing the clodinafop-propargyl ratio in mixtures (90% clodinafop-propargyl + 10% mesosulfuron + iodosulfuron increased wild oat control compared with other mixing ratios remarkably.

Cooking methods employing natural anti-oxidant food additives effectively reduced concentration of nephrotoxic and carcinogenic aristolochic acids in contaminated food grains.

Science.gov (United States)

Li, Weiwei; Chan, Chi-Kong; Wong, Yee-Lam; Chan, K K Jason; Chan, Ho Wai; Chan, Wan

2018-10-30

Emerging evidence suggests that aristolochic acids (AA) produced naturally by a common weed Aristolochia clematitis in the cultivation fields is contaminating the food products in Balkan Peninsula and acting as the etiological agent in the development of Balkan endemic nephropathy. In this study, we investigated the combined use of natural anti-oxidative "food additives" and different cooking methods to find a solution for the widespread contamination of AA in food products. The results indicated that the addition of healthy dietary supplements (such as cysteine, glutathione, ascorbic acid, citric acid and magnesium) during cooking, is a highly efficient method in lowering the concentration of AA in the final food products. Because previous observation indicated one of the toxicological mechanisms by which AA exert its toxicity is to induce oxidative stress in internal organs, it is anticipated that these added anti-oxidants will also help to attenuate the nephrotoxicity of AA. Copyright © 2018 Elsevier Ltd. All rights reserved.

Method and techniques of radioactive waste treatment

International Nuclear Information System (INIS)

Ghafar, M.; Aasi, N.

2002-04-01

This study illustrates the characterization of radioactive wastes produced by the application of radioisotopes in industry and research. The treatment methods of such radioactive wastes, chemical co-precipitation and ion exchange depending on the technical state of radioactive waste management facility in Syria were described. The disposal of conditioned radioactive wastes, in a safe way, has been discussed including the disposal of the radioactive sources. The characterizations of the repository to stock conditioned radioactive wastes were mentioned. (author)

Innovative methods for knowledge transfer

Science.gov (United States)

Goanta, A. M.

2015-11-01

At this time, learning takes place, either with classic books on paper support or using books scanned or drawn and further converted into PDF or PPT files that are printed on type support CD / DVD. The latter modern means of learning, the study adds live on the Internet using search engines and not least e-learning method, which allows the study of bibliographic related materials in PDF or PPT, stacked and grouped on the basis of a curriculum imposed which can be accessed on a website via a user name and password. Innovative methods come to successfully use other file types than those mentioned above. The graphics in teaching technical subjects such as descriptive geometry can be achieved using animated PowerPoint files, allowing for visualization of steps to be taken, in the case of solving by drawing a descriptive geometry. Another innovative method relies on the use of HTML files, inspired by related sites help design software packages that can be used when teaching descriptive geometry that the technical design. Through this work, the author has proposed to present a new innovative method, which is inspired by the methods listed above, but involves using AVI files to teaching of computer-assisted type graphics or info graphics. In general this new author's method lends itself particularly well to the teaching of the use of software packages because the student actually see the place from where the delivered command is accessed and contextual options of right button of the mouse. These laboratory courses or mentoring can be freestanding cards support CD / DVD or can be posted on websites with restricted access based on user name and password. Practically paper presents the methodology of creating courses and tutorials in AVI format, and how to monitor the degree of accessing the website, on which there were posted mentioned teaching materials, using the tools offered by Google Analytics. The results consist of graphical work, about the degree of access to

A square-wave adsorptive stripping voltammetric method for the determination of Amaranth, a food additive dye.

Science.gov (United States)

Alghamdi, Ahmad H

2005-01-01

Square-wave adsorptive stripping voltammetric (AdSV) determinations of trace concentrations of the azo coloring agent Amaranth are described. The analytical methodology used was based on the adsorptive preconcentration of the dye on the hanging mercury drop electrode, followed by initiation of a negative sweep. In a pH 10 carbonate supporting electrolyte, Amaranth gave a well-defined and sensitive AdSV peak at -518 mV. The electroanalytical determination of this azo dye was found to be optimal in carbonate buffer (pH 10) under the following experimental conditions: accumulation time, 120 s; accumulation potential, 0.0 V; scan rate, 600 mV/s; pulse amplitude, 90 mV; and frequency, 50 Hz. Under these optimized conditions the AdSV peak current was proportional over the concentration range 1 x 10(-8)-1.1 x 10(-7) mol/L (r = 0.999) with a detection limit of 1.7 x 10(-9) mol/L (1.03 ppb). This analytical approach possessed enhanced sensitivity, compared with conventional liquid chromatography or spectrophotometry and it was simple and fast. The precision of the method, expressed as the relative standard deviation, was 0.23%, whereas the accuracy, expressed as the mean recovery, was 104%. Possible interferences by several substances usually present as food additive azo dyes (E110, E102), gelatin, natural and artificial sweeteners, preservatives, and antioxidants were also investigated. The developed electroanalyticals method was applied to the determination of Amaranth in soft drink samples, and the results were compared with those obtained by a reference spectrophotometric method. Statistical analysis (paired t-test) of these data showed that the results of the 2 methods compared favorably.

System and method for high power diode based additive manufacturing

Science.gov (United States)

El-Dasher, Bassem S.; Bayramian, Andrew; Demuth, James A.; Farmer, Joseph C.; Torres, Sharon G.

2016-04-12

A system is disclosed for performing an Additive Manufacturing (AM) fabrication process on a powdered material forming a substrate. The system may make use of a diode array for generating an optical signal sufficient to melt a powdered material of the substrate. A mask may be used for preventing a first predetermined portion of the optical signal from reaching the substrate, while allowing a second predetermined portion to reach the substrate. At least one processor may be used for controlling an output of the diode array.

System and method for high power diode based additive manufacturing

Energy Technology Data Exchange (ETDEWEB)

El-Dasher, Bassem S.; Bayramian, Andrew; Demuth, James A.; Farmer, Joseph C.; Torres, Sharon G.

2018-01-02

A system is disclosed for performing an Additive Manufacturing (AM) fabrication process on a powdered material forming a substrate. The system may make use of a diode array for generating an optical signal sufficient to melt a powdered material of the substrate. A mask may be used for preventing a first predetermined portion of the optical signal from reaching the substrate, while allowing a second predetermined portion to reach the substrate. At least one processor may be used for controlling an output of the diode array.

Pose Measurement Method and Experiments for High-Speed Rolling Targets in a Wind Tunnel

Directory of Open Access Journals (Sweden)

Zhenyuan Jia

2014-12-01

Full Text Available High-precision wind tunnel simulation tests play an important role in aircraft design and manufacture. In this study, a high-speed pose vision measurement method is proposed for high-speed and rolling targets in a supersonic wind tunnel. To obtain images with high signal-to-noise ratio and avoid impacts on the aerodynamic shape of the rolling targets, a high-speed image acquisition method based on ultrathin retro-reflection markers is presented. Since markers are small-sized and some of them may be lost when the target is rolling, a novel markers layout with which markers are distributed evenly on the surface is proposed based on a spatial coding method to achieve highly accurate pose information. Additionally, a pose acquisition is carried out according to the mentioned markers layout after removing mismatching points by Case Deletion Diagnostics. Finally, experiments on measuring the pose parameters of high-speed targets in the laboratory and in a supersonic wind tunnel are conducted to verify the feasibility and effectiveness of the proposed method. Experimental results indicate that the position measurement precision is less than 0.16 mm, the pitching and yaw angle precision less than 0.132° and the roll angle precision 0.712°.

Pose measurement method and experiments for high-speed rolling targets in a wind tunnel.

Science.gov (United States)

Jia, Zhenyuan; Ma, Xin; Liu, Wei; Lu, Wenbo; Li, Xiao; Chen, Ling; Wang, Zhengqu; Cui, Xiaochun

2014-12-12

High-precision wind tunnel simulation tests play an important role in aircraft design and manufacture. In this study, a high-speed pose vision measurement method is proposed for high-speed and rolling targets in a supersonic wind tunnel. To obtain images with high signal-to-noise ratio and avoid impacts on the aerodynamic shape of the rolling targets, a high-speed image acquisition method based on ultrathin retro-reflection markers is presented. Since markers are small-sized and some of them may be lost when the target is rolling, a novel markers layout with which markers are distributed evenly on the surface is proposed based on a spatial coding method to achieve highly accurate pose information. Additionally, a pose acquisition is carried out according to the mentioned markers layout after removing mismatching points by Case Deletion Diagnostics. Finally, experiments on measuring the pose parameters of high-speed targets in the laboratory and in a supersonic wind tunnel are conducted to verify the feasibility and effectiveness of the proposed method. Experimental results indicate that the position measurement precision is less than 0.16 mm, the pitching and yaw angle precision less than 0.132° and the roll angle precision 0.712°.

Paleomagnetic intensity of Aso pyroclastic flows: Additional results with LTD-DHT Shaw method, Thellier method with pTRM-tail check

Science.gov (United States)

Maruuchi, T.; Shibuya, H.

2009-12-01

For the sake to calibrate the absolute value of the ’relative paleointensity variation curve’ drawn from sediment cores, Takai et al. (2002) proposed to use pyroclastic flows co-bearing with wide spread tephras. The pyroclastic flows prepare volcanic rocks with TRM, which let us determine absolute paleointensity, and the tephras prepare the correlation with sediment stratigraphy. While 4 out of 6 pyroclastic flows are consistent with Sint-800 paleointensity variation curve, two flows, Aso-2 and Aso-4, show weaker and stronger than Sint-800 beyond the error, respectively. We revisited the paleointensity study of Aso pyroclastic flows, adding LTD- DHT Shaw method, the pTRM-tail check in Thellier experiment, and LTD-DHT Shaw method by using volcanic glasses. We prepared 11 specimens from 3 sites of Aso-1 welded tuff for LTD-DHT Shaw method experiments, and obtained 6 paleointensities satisfied a set of strict criteria. They yield an average paleointensity of 21.3±5.8uT, which is smaller than 31.0±3.4uT provided by Takai et al. (2002). For Aso-2 welded tuff, 11 samples from 3 sites were submitted to Thellier experiments, and 6 passed a set of pretty stringent criteria including pTRM-tail check, which is not performed by Takai et al. (2002). They give an average paleointensity of 20.2±1.5uT, which is virtually identical to 20.2±1.0uT (27 samples) given by Takai et al. (2002). Although the success rate was not good in LTD-DHT Shaw method, 2 out of 12 specimens passed the criteria, and gave 25.8±3.4uT, which is consistent with Takai et al. (2002). In addition, we obtained a reliable paleointensity from a volcanic glass in LTD-DHT Shaw method, it gives a paleointensity of 23.6 uT. It is also consitent with Takai et al. (2002). For Aso-3 welded tuff, we performed only LTD-DHT Shaw method for one specimen from one site yet. It gives a paleointensity of 43.0uT, which is higher than 31.8±3.6uT given by Takai et al. (2002). Eight sites were set for Aso-4 welded tuff

EXPLANATORY METHODS OF MARKETING DATA ANALYSIS – THEORETICAL AND METHODOLOGICAL CONSIDERATIONS

Directory of Open Access Journals (Sweden)

Rozalia GABOR

2010-01-01

Full Text Available Explanatory methods of data analysis – also named by some authors supervised learning methods - enable researchers to identify and analyse configurations of relations between two or several variables, most of them with a high accuracy, as there is possibility of testing statistic significance by calculating the confidence level associated with validation of relation concerned across the entire population and not only the surveyed sample. The paper shows some of these methods, respectively: variance analysis, covariance analysis, segmentation and discriminant analysis with the mention - for every method – of applicability area for marketing research.

Method for the determination of natural ester-type gum bases used as food additives via direct analysis of their constituent wax esters using high-temperature GC/MS.

Science.gov (United States)

Tada, Atsuko; Ishizuki, Kyoko; Yamazaki, Takeshi; Sugimoto, Naoki; Akiyama, Hiroshi

2014-07-01

Natural ester-type gum bases, which are used worldwide as food additives, mainly consist of wax esters composed of long-chain fatty acids and long-chain fatty alcohols. There are many varieties of ester-type gum bases, and thus a useful method for their discrimination is needed in order to establish official specifications and manage their quality control. Herein is reported a rapid and simple method for the analysis of different ester-type gum bases used as food additives by high-temperature gas chromatography/mass spectrometry (GC/MS). With this method, the constituent wax esters in ester-type gum bases can be detected without hydrolysis and derivatization. The method was applied to the determination of 10 types of gum bases, including beeswax, carnauba wax, lanolin, and jojoba wax, and it was demonstrated that the gum bases derived from identical origins have specific and characteristic total ion chromatogram (TIC) patterns and ester compositions. Food additive gum bases were thus distinguished from one another based on their TIC patterns and then more clearly discriminated using simultaneous monitoring of the fragment ions corresponding to the fatty acid moieties of the individual molecular species of the wax esters. This direct high-temperature GC/MS method was shown to be very useful for the rapid and simple discrimination of varieties of ester-type gum bases used as food additives.

Method for the determination of natural ester-type gum bases used as food additives via direct analysis of their constituent wax esters using high-temperature GC/MS

Science.gov (United States)

Tada, Atsuko; Ishizuki, Kyoko; Yamazaki, Takeshi; Sugimoto, Naoki; Akiyama, Hiroshi

2014-01-01

Natural ester-type gum bases, which are used worldwide as food additives, mainly consist of wax esters composed of long-chain fatty acids and long-chain fatty alcohols. There are many varieties of ester-type gum bases, and thus a useful method for their discrimination is needed in order to establish official specifications and manage their quality control. Herein is reported a rapid and simple method for the analysis of different ester-type gum bases used as food additives by high-temperature gas chromatography/mass spectrometry (GC/MS). With this method, the constituent wax esters in ester-type gum bases can be detected without hydrolysis and derivatization. The method was applied to the determination of 10 types of gum bases, including beeswax, carnauba wax, lanolin, and jojoba wax, and it was demonstrated that the gum bases derived from identical origins have specific and characteristic total ion chromatogram (TIC) patterns and ester compositions. Food additive gum bases were thus distinguished from one another based on their TIC patterns and then more clearly discriminated using simultaneous monitoring of the fragment ions corresponding to the fatty acid moieties of the individual molecular species of the wax esters. This direct high-temperature GC/MS method was shown to be very useful for the rapid and simple discrimination of varieties of ester-type gum bases used as food additives. PMID:25473499

A improved tidal method without water level

Science.gov (United States)

Luo, xiaowen

2017-04-01

Now most tide are obtained use water Level and pressure type water gage, but it is difficult to install them and reading is in low accuracy in this method . In view of above-mentioned facts, In order to improve tide accuracy, A improved method is introduced.sea level is obtained in given time using high-precision GNSS buoy combined instantaneous position from pressure gage. two steps are as following, (1) the GNSS time service is used as the source of synchronization reference in tidal measurement; (2) centimeter-level sea surface positions are obtained in real time using difference GNSS The improved method used in seafloor topography survey，in 145 cross points, 95% meet the requirements of the Hydrographic survey specification. It is effective method to obtain higher accuracy tide.

Method for the enrichment of isotopes

International Nuclear Information System (INIS)

Schuster, E.; Kersting, A.; Gebauhr, W.

1976-01-01

A method for the enrichment of isotopes, especially of uranium compounds, is described, working according to the principle of selective excitation by laser beams. As the starting compound, UF 6 is mentioned; the reaction partness are atomic gases (hydrogen, oxygen, nitrogen) or radicals (CH 3 , CHO). According to the invention, the gas mixture flows through the reaction space with a velocity so large that in leaving it, recombination of the reaction partner will already take place again. In this way, competing thermal reactions will be avoided and energy transfer fo excited 235 U molecules to non-excited 238 U molecules is eliminated to a large extent. A suitable equipment for implementing the method is described. (UWI) [de

METHODS TO QUANTIFY THE UNDERGROUND ECONOMY

Directory of Open Access Journals (Sweden)

Oana Simona HUDEA

2017-12-01

Full Text Available The underground economy issue has raised in time miscellaneous discussions, it representing a large interest problem that affects the nations all over the world, without exception and, thereby, the well—being of stand—alone individuals. Although also treated in some previous works of the author, this topic in herein approached from a different perspective, namely the one related to distinct methods to be used in order to capture, by quantification, this undesirable economic form. Such methods, empirically tested or just imposed, based on arguments, by the researchers having launched the same, are rendered while considering their pluses and minuses in revealing, with a reasonable accuracy, the level of the above—mentioned informal economy.

Additive Manufacturing in the Marine Corps

Science.gov (United States)

2015-06-01

TERMS additive manufacturing, 3D printing, improving logistics 15. NUMBER OF PAGES 123 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT...One such method is ultrasonic agglomeration. The process produces compact snack items that are nutrient-dense and shelf-stable. Currently Army...possess outdated technology. Additionally, prices for the printers are dropping significantly.202 Therefore, the Marine Corps will not only have outdated

PicPrint: Embedding pictures in additive manufacturing

DEFF Research Database (Denmark)

Nielsen, Jannik Boll; Eiríksson, Eyþór Rúnar; Lyngby, Rasmus Ahrenkiel

2017-01-01

Here  we  present  PicPrint,  a  method  and  tool  for  producing  an  additively  manufactured  lithophane,  enabling  transferring  and embedding  2D  information  into  additively  manufactured  3D  objects.  The  method  takes  an  input  image  and  converts  it  to  a......, after which  the mesh is  ready  for either  direct  print  on an additive manufacturing system, or transfer to other geometries via Boolean mesh operations. ...

An additional trigeminal system in certain snakes possessing infrared receptors

NARCIS (Netherlands)

Molenaar, Gerard J.

1974-01-01

This communication describes a nucleus and tract of the trigeminal system whose existence is not mentioned in any account of brain stem architecture known to the present author. The structures were first recognised in the brain stem of a giant snake (Python reticulatus) and later were also found

Most consumed processed foods by patients on hemodialysis: Alert for phosphate-containing additives and the phosphate-to-protein ratio.

Science.gov (United States)

Watanabe, Marcela T; Araujo, Raphael M; Vogt, Barbara P; Barretti, Pasqual; Caramori, Jacqueline C T

2016-08-01

Hyperphosphatemia is common in patients with chronic kidney disease (CKD) stages IV and V because of decreased phosphorus excretion. Phosphatemia is closely related to dietary intake. Thus, a better understanding of sources of dietary phosphate consumption, absorption and restriction, particularly inorganic phosphate found in food additives, is key to prevent consequences of this complication. Our aims were to investigate the most commonly consumed processed foods by patients with CKD on hemodialysis, to analyze phosphate and protein content of these foods using chemical analysis and to compare these processed foods with fresh foods. We performed a cross-sectional descriptive analytical study using food frequency questionnaires to rank the most consumed industrialized foods and beverages. Total phosphate content was determined by metavanadate colorimetry, and nitrogen content was determined by the Kjeldahl method. Protein amounts were estimated from nitrogen content. The phosphate-to-protein ratio (mg/g) was then calculated. Processed meat protein and phosphate content were compared with the nutritional composition of fresh foods using the Brazilian Food Composition Table. Phosphate measurement results were compared with data from the Food Composition Table - Support for Nutritional Decisions. An α level of 5% was considered significant. Food frequency questionnaires were performed on 100 patients (mean age, 59 ± 14 years; 57% male). Phosphate additives were mentioned on 70% of the product labels analyzed. Proteins with phosphate-containing additives provided approximately twice as much phosphate per gram of protein compared with that of fresh foods (p processed foods are higher than those of fresh foods, as well as phosphate-to-protein ratio. A better understanding of phosphate content in foods, particularly processed foods, may contribute to better control of phosphatemia in patients with CKD. Copyright © 2016 European Society for Clinical Nutrition and

An implementation framework for additive manufacturing in supply chains

Directory of Open Access Journals (Sweden)

Raed Handal

2017-12-01

Full Text Available Additive manufacturing has become one of the most important technologies in the manufacturing field. Full implementation of additive manufacturing will change many well-known management practices in the production sector. However, theoretical development in the field of additive manufacturing with regard to its impact on supply chain management is rare. While additive manufacturing is believed to revolutionize and enhance traditional manufacturing, there is no comprehensive toolset developed in the manufacturing field to assess the impact of additive manufacturing and determine the best production method that suits the applied supply chain strategy. A significant portion of the existing supply chain methods and frameworks were adopted in this study to examine the implementation of additive manufacturing in supply chain management. The aim of this study is to develop a framework to explain when additive manufacturing impacts supply chain management efficiently.

Method for the validation and uncertainty estimation of tocopherol analysis applied to soybean oil with addition of spices and TBHQ

Directory of Open Access Journals (Sweden)

da Silva, M. G.

2013-09-01

Full Text Available The tocopherol contents of refined soybean oil with the addition of rosemary, oregano, garlic, annatto seeds and TBHQ was evaluated during storage at 25 °C and 35 °C for twelve months, in comparison with a control soybean oil without the antioxidant addition. The method proposed to assess the tocopherol content was validated and the uncertainty estimation was determined. The method presented adequate linearity and precision, accuracy between 93% and 103% and expanded uncertainty of 2%. The contents of α-, γ- and δ-tocopherols of all the tested soybean oils remained constant during the storage at 25 °C and 35 °C regardless of antioxidant addition, while β-tocopherol content decreased. The addition of a mixture of rosemary, oregano, garlic and annatto seeds increased the concentration of γ- and δ-tocopherol. The oil with spices presented a similar behavior to that of the oil with the addition of TBHQ.La concentración de tocoferoles en aceite de soja refinado (muestra control, aceite de soja adicionado de romero, orégano, ajo, semilla de achiote y TBHQ fueron cuantificados durante el almacenamiento durante 12 meses a 25°C y 35°C. El método propuesto para medir tocoferoles fue validado y determinada la incertidumbre. Este método presentó linealidad y precisión adecuadas, exactitud entre 93% y 103% además de una incertidumbre expandida de 2%. Las cantidades de α-, γ- y δ-tocoferol en el aceite de soja refinado, aceite de soja adicionado de condimentos y aceite de soja adicionado con TBHQ se mantuvieron constantes durante el almacenamiento a 25°C y 35°C con excepción del β-tocoferol el cual disminuyó. El aceite de soja adicionado de condimentos (romero, orégano, ajo, y semilla de achiote presentó mayores concentraciones de γ- y δ-tocoferol en comparación con el aceite de soja refinado utilizado como control. El aceite de soja adicionado de condimentos presentó un comportamiento semejante al aceite de soja adicionado

Radioisotope methods for leucocyte labelling

Energy Technology Data Exchange (ETDEWEB)

Kostadinova, I; Kovacheva, S [Meditsinska Akademiya, Sofia (Bulgaria). Katedra po Rentgenologiya i Radiologiya

1988-01-01

A review is made of the labelling methods with the following tracers: {sup 3}H-thymidine, {sup 32}P-DP, {sup 111}In (oxine, tropolon, acetylacetone, MERC), {sup 99m}Tc (reduced {sup 99m}Tc, lypophyl {sup 99m}Tc-complexes and {sup 99m}Tc-colloids). The main diagnosis areas are mentioned: abdominal abscesses and inflammations, inflammation foci of skeleton or of implanted prosthesis; acute myocardial infarction, bacterial endocarditis, rejection of kydney transplantations or vascular grafts. It is concluded that labelled leucocytes are very reliable for noninvasive diagnosis of inflammation foci with unclear localization.

Hybrid perturbation methods based on statistical time series models

Science.gov (United States)

San-Juan, Juan Félix; San-Martín, Montserrat; Pérez, Iván; López, Rosario

2016-04-01

In this work we present a new methodology for orbit propagation, the hybrid perturbation theory, based on the combination of an integration method and a prediction technique. The former, which can be a numerical, analytical or semianalytical theory, generates an initial approximation that contains some inaccuracies derived from the fact that, in order to simplify the expressions and subsequent computations, not all the involved forces are taken into account and only low-order terms are considered, not to mention the fact that mathematical models of perturbations not always reproduce physical phenomena with absolute precision. The prediction technique, which can be based on either statistical time series models or computational intelligence methods, is aimed at modelling and reproducing missing dynamics in the previously integrated approximation. This combination results in the precision improvement of conventional numerical, analytical and semianalytical theories for determining the position and velocity of any artificial satellite or space debris object. In order to validate this methodology, we present a family of three hybrid orbit propagators formed by the combination of three different orders of approximation of an analytical theory and a statistical time series model, and analyse their capability to process the effect produced by the flattening of the Earth. The three considered analytical components are the integration of the Kepler problem, a first-order and a second-order analytical theories, whereas the prediction technique is the same in the three cases, namely an additive Holt-Winters method.

Development and validation of a multi-analyte method for the regulatory control of carotenoids used as feed additives in fish and poultry feed.

Science.gov (United States)

Vincent, Ursula; Serano, Federica; von Holst, Christoph

2017-08-01

Carotenoids are used in animal nutrition mainly as sensory additives that favourably affect the colour of fish, birds and food of animal origin. Various analytical methods exist for their quantification in compound feed, reflecting the different physico-chemical characteristics of the carotenoid and the corresponding feed additives. They may be natural products or specific formulations containing the target carotenoids produced by chemical synthesis. In this study a multi-analyte method was developed that can be applied to the determination of all 10 carotenoids currently authorised within the European Union for compound feedingstuffs. The method functions regardless of whether the carotenoids have been added to the compound feed via natural products or specific formulations. It is comprised of three steps: (1) digestion of the feed sample with an enzyme; (2) pressurised liquid extraction; and (3) quantification of the analytes by reversed-phase HPLC coupled to a photodiode array detector in the visible range. The method was single-laboratory validated for poultry and fish feed covering a mass fraction range of the target analyte from 2.5 to 300 mg kg - 1 . The following method performance characteristics were obtained: the recovery rate varied from 82% to 129% and precision expressed as the relative standard deviation of intermediate precision varied from 1.6% to 15%. Based on the acceptable performance obtained in the validation study, the multi-analyte method is considered fit for the intended purpose.

Simultaneous Determination of Eosin-Yellow and Ponceau-S Using H-Point Standard Addition Method in Micellar Media

Directory of Open Access Journals (Sweden)

Amandeep Kaur

2012-01-01

Full Text Available H-point standard addition method (HPSAM is developed for simultaneous determination of eosin-Y and ponceau-s in micellar media. Nickel chloride (NiCl2 is used as chromogenic reagent for complexes formation of eosin-Y and ponceau-S food colorants. The measurements were carried out using sodium lauryl sulphate as a surfactant, in buffered solution at pH 6.0. The concentration range of 0.115-2.53 μg/mL of eosin-Y and 0.159-3.80 μg/mL of ponceau-S. The proposed procedures have been applied successfully for the simultaneous determination of eosin-Y and ponceau-S in synthetic binary mixtures and real samples.

An analytical-numerical comprehensive method for optimizing the fringing magnetic field

International Nuclear Information System (INIS)

Xiao Meiqin; Mao Naifeng

1991-01-01

The criterion of optimizing the fringing magnetic field is discussed, and an analytical-numerical comprehensive method for realizing the optimization is introduced. The method mentioned above consists of two parts, the analytical part calculates the field of the shims, which corrects the fringing magnetic field by using uniform magnetizing method; the numerical part fulfils the whole calculation of the field distribution by solving the equation of magnetic vector potential A within the region covered by arbitrary triangular meshes with the aid of finite difference method and successive over relaxation method. On the basis of the method, the optimization of the fringing magnetic field for a large-scale electromagnetic isotope separator is finished

Laser polishing of additive manufactured Ti alloys

Science.gov (United States)

Ma, C. P.; Guan, Y. C.; Zhou, W.

2017-06-01

Laser-based additive manufacturing has attracted much attention as a promising 3D printing method for metallic components in recent years. However, surface roughness of additive manufactured components has been considered as a challenge to achieve high performance. In this work, we demonstrate the capability of fiber laser in polishing rough surface of additive manufactured Ti-based alloys as Ti-6Al-4V and TC11. Both as-received surface and laser-polished surfaces as well as cross-section subsurfaces were analyzed carefully by White-Light Interference, Confocal Microscope, Focus Ion Beam, Scanning Electron Microscopy, Energy Dispersive Spectrometer, and X-ray Diffraction. Results revealed that as-received Ti-based alloys with surface roughness more than 5 μm could be reduce to less than 1 μm through laser polishing process. Moreover, microstructure, microhardness and wear resistance of laser-polished zone was investigated in order to examine the thermal effect of laser polishing processing on the substrate of additive manufactured Ti alloys. This proof-of-concept process has the potential to effectively improve the surface roughness of additive manufactured metallic alloy by local polishing method without damage to the substrate.

The present conditions of interpretation and findings report in UGI series examination (The Japanese society gastrointestinal imaging report group performed questionary survey)

International Nuclear Information System (INIS)

Sato, Shinsuke; Aoki, Ryosuke; Yoshida, Takashi; Nishikawa, Takashi; Takahashi, Nobuyuki; Ishimoto, Yuji

2008-01-01

The Japanese society gastrointestinal imaging report group performed questionary survey to relate to interpretation of radiogram of radiological technologist and findings report in upper GI series examination for 599 national institutions. Response rate was 27%, and many of answers were the institutions where surgical treatment was possible. Additional radiography examining by radiological technologist depending on the situation and, it was recognized a doctor furthermore, institutions more than 70% made findings report after examination, and, as for the mention methods of findings report, there was difference in mention contents, and character by examination classification. It seemed the mention methods that we unified were difficult nationwide, and, however, as for the making of the findings report which used diagnosis flow chart, it was thought with possibility in future by enlightenment active. (author)

Predicting Color Output of Additive Manufactured Parts

DEFF Research Database (Denmark)

Eiríksson, Eyþór Rúnar; Pedersen, David Bue; Aanæs, Henrik

2015-01-01

In this paper we address the colorimetric performance of a multicolor additive manufacturing process. A method on how to measure and characterize color performance of said process is presented. Furthermore, a method on predicting the color output is demonstrated, allowing for previsualization...

NEW DATA ADDITION TO THE ROMANIAN

Directory of Open Access Journals (Sweden)

OPREA ADRIAN

2012-12-01

Full Text Available A number of seven plant taxa are presented in this paper, some of them being now for the first time reported in Romania (e. g. Cenchrus longispinus, Panicum miliaceum subsp. ruderale; Panicum miliaceum subsp. agricolum; Robinia neomexicana, while other taxa are mentioned for the first time in the flora of some historical provinces (e. g. Oenothera parviflora L. in Oltenia, or. Setaria faberi R. A. W. Herrm. in Moldavia; other taxa are newly identified in the flora of various counties (e. g. Reynoutria × bohemica in Bihor, Sălaj, Cluj, Caraş-Severin, Vâlcea, Prahova, and Bacău counties; Reynoutria sachalinensis in Caraş-Severin County.

Optimization of surveillance methods of water radionuclide intake by man

Energy Technology Data Exchange (ETDEWEB)

Pakulo, A.G. (Institut Biofiziki, Moscow (USSR))

1984-11-01

A method has been suggested to test and sample prepared food stuffs, when studying and analyzing the intake of radionuclides from aqueous food chains to people. The method is characterized by the following advantages: a possibility to establish to a greater accuracy the amount of consumed products, as compared with inquiry method; a possibility to determine the actual radionuclide contents in prepared food without introduction of correcting coefficients for isotope translocation to the ration during culinary treatment of raw food stuff. Different ways of preparation are known to affect differently the degree of isotope translocaton to the ration. The above-mentioned method under certain conditions seems to be handy while excluding preliminary treatment of samples.

Radiological aspects of the usability of red mud as building material additive

International Nuclear Information System (INIS)

Somlai, Janos; Jobbagy, Viktor; Kovacs, Jozsef; Tarjan, Sandor; Kovacs, Tibor

2008-01-01

Several researchers have examined and achieved favourable results in connection with the building industry's use of red mud extracted in large quantities from the processing of bauxite. These days more and more precedence is being given to limiting the radiological dose to the population. In this study carried out in Hungary, the use of red mud, bauxite, and clay additives recommended for the production of special cements, were examined from a radiological aspect. 226 Ra and 232 Th activity concentrations measured in Hungarian bauxite, red mud and clay samples were significantly similar with the levels for such raw materials mentioned in international literature. Taking radiation protection aspects into consideration, none of these products can be directly used for building construction. Taking Hungarian and international values into consideration, a small amount of red mud, not exceeding 15% could be used for brick production, for example as a colouring material. However, beyond this amount the standards for building materials would not be met. For the production of cements an even stricter limit needs to be determined when both bauxite and red mud are used

Functional methods and mappings of dissipative quantum systems

International Nuclear Information System (INIS)

Baur, H.

2006-01-01

In the first part of this work we extract the algebraic structure behind the method of the influence functional in the context of dissipative quantum mechanics. Special emphasis was put on the transition from a quantum mechanical description to a classical one, since it allows a deeper understanding of the measurement-process. This is tightly connected with the transition from a microscopic to a macroscopic world where the former one is described by the rules of quantum mechanics whereas the latter follows the rules of classical mechanics. In addition we show how the results of the influence functional method can be interpreted as a stochastical process, which in turn allows an easy comparison with the well known time development of a quantum mechanical system by use of the Schroedinger equation. In the following we examine the tight-binding approximation of models of which their hamiltionian shows discrete eigenstates in position space and where transitions between those states are suppressed so that propagation either is described by tunneling or by thermal activation. In the framework of dissipative quantum mechanics this leads to a tremendous simplification of the effective description of the system since instead of looking at the full history of all paths in the path integral description, we only have to look at all possible jump times and the possible corresponding set of weights for the jump direction, which is much easier to handle both analytically and numerically. In addition we deal with the mapping and the connection of dissipative quantum mechanical models with ones in quantum field theory and in particular models in statistical field theory. As an example we mention conformal invariance in two dimensions which always becomes relevant if a statistical system only has local interaction and is invariant under scaling. (orig.)

Comprehensive European dietary exposure model (CEDEM) for food additives.

Science.gov (United States)

Tennant, David R

2016-05-01

European methods for assessing dietary exposures to nutrients, additives and other substances in food are limited by the availability of detailed food consumption data for all member states. A proposed comprehensive European dietary exposure model (CEDEM) applies summary data published by the European Food Safety Authority (EFSA) in a deterministic model based on an algorithm from the EFSA intake method for food additives. The proposed approach can predict estimates of food additive exposure provided in previous EFSA scientific opinions that were based on the full European food consumption database.

Degradation of phenol and Cr (VI) wastewater with contact glow discharge electrolysis method and the addition of Fe2+

Science.gov (United States)

Kurniawan, Raden Ridzki Aditya; Saksono, Nelson

2017-11-01

Phenol and Cr (VI) are an organic waste and dangerous heavy metals which generated from a wide variety of industrial processes such as textiles, paints, dyes, and others. For that reason, we need effective waste treatment technologies, one of them is Contact Glow Discharge Electrolysis (CGDE). This method produce reactive species such as radical hidroxyl so as to be able to degradate phenol and Cr(VI) wastewater effectively. This research aims to obtain the effect of Fe 2+ and air bubbles in degradation of phenol and Cr (VI) waste simultaneously. Waste degradation is measured its absorbance with UV-Vis spectrophotometer. In the conditions of 600 Volt voltage, Na2SO4 0.02 M, anode depth of 1.5 cm, the addition of Fe2+ 40 ppm and the addition of air bubbles for 30 minutes was obtained a percentage degradation of phenol 99.47%, Cr (VI) 76.75% and specific energy of 344.473 kJ / mmol.

Manual of analytical methods for the Industrial Hygiene Chemistry Laboratory

Energy Technology Data Exchange (ETDEWEB)

Greulich, K.A.; Gray, C.E. (comp.)

1991-08-01

This Manual is compiled from techniques used in the Industrial Hygiene Chemistry Laboratory of Sandia National Laboratories in Albuquerque, New Mexico. The procedures are similar to those used in other laboratories devoted to industrial hygiene practices. Some of the methods are standard; some, modified to suit our needs; and still others, developed at Sandia. The authors have attempted to present all methods in a simple and concise manner but in sufficient detail to make them readily usable. It is not to be inferred that these methods are universal for any type of sample, but they have been found very reliable for the types of samples mentioned.

Manual of analytical methods for the Industrial Hygiene Chemistry Laboratory

International Nuclear Information System (INIS)

Greulich, K.A.; Gray, C.E.

1991-08-01

This Manual is compiled from techniques used in the Industrial Hygiene Chemistry Laboratory of Sandia National Laboratories in Albuquerque, New Mexico. The procedures are similar to those used in other laboratories devoted to industrial hygiene practices. Some of the methods are standard; some, modified to suit our needs; and still others, developed at Sandia. The authors have attempted to present all methods in a simple and concise manner but in sufficient detail to make them readily usable. It is not to be inferred that these methods are universal for any type of sample, but they have been found very reliable for the types of samples mentioned

Effusion method at age 69: current state of the art

International Nuclear Information System (INIS)

Cater, E.D.

1979-01-01

Historical notes are presented tracing the development of the effusion methods along with some fundamental equations to be used later. Theoretical and experimental limitations of the method, and of each variant of the effusion method are cited. How these problems have been dealt with and where our understanding of them now lies are discussed, and estimates of the accuracy with which derived results can be ascribed are given. Finally, some newer techniques are mentioned which give some of the same results that have traditionally been obtained by effusion studies, try to place them in perspective, and perhaps suggest some future directions for effusion studies

Franchising as a method of entering the market

OpenAIRE

Kolář, Jan

2008-01-01

This bachelor thesis deals with franchising as a method of entering the market. My work is divided into theoretical and practical part. In the first part I describe the essential principals of functioning every franchising system. I explain the mutual relationship between franchisor and franchisee and also advantages and disadvantages for both of them. As a next part I mention the importance of using franchising in the world and also in the Czech Republic. Practical part deals with concrete u...

ADDITIVE SELF-HELICITY AS A KINK MODE THRESHOLD

International Nuclear Information System (INIS)

Malanushenko, A.; Longcope, D. W.; Fan, Y.; Gibson, S. E.

2009-01-01

In this paper, we propose that additive self-helicity, introduced by Longcope and Malanushenko, plays a role in the kink instability for complex equilibria, similar to twist helicity for thin flux tubes. We support this hypothesis by a calculation of additive self-helicity of a twisted flux tube from the simulation of Fan and Gibson. As more twist gets introduced, the additive self-helicity increases, and the kink instability of the tube coincides with the drop of additive self-helicity, after the latter reaches the value of H A /Φ 2 ∼ 1.5 (where Φ is the flux of the tube and H A is the additive self-helicity). We compare the additive self-helicity to twist for a thin subportion of the tube to illustrate that H A /Φ 2 is equal to the twist number, studied by Berger and Field, when the thin flux tube approximation is applicable. We suggest that the quantity H A /Φ 2 could be treated as a generalization of a twist number, when the thin flux tube approximation is not applicable. A threshold on a generalized twist number might prove extremely useful studying complex equilibria, just as the twist number itself has proven useful studying idealized thin flux tubes. We explicitly describe a numerical method for calculating additive self-helicity, which includes an algorithm for identifying a domain occupied by a flux bundle and a method of calculating potential magnetic field confined to this domain. We also describe a numerical method to calculate twist of a thin flux tube, using a frame parallelly transported along the axis of the tube.

Electrospining method to synthesize compositebased on alginate-polyvinyl alcohol with addition of snail (Achatina fulica)

International Nuclear Information System (INIS)

Meilanny DKP; Pranjono; Dyah Hikmawati

2015-01-01

Many materials that can be used as wound coverings, one is alginate. Alginate has a high absorption capacity and has a role as a gelling agent which has hemostatic properties. Rigid and brittle nature is weakness of alginate and to improve the properties of the alginate can be mixed with the vinyl polymers are compatible and flexible. PVA is a water-soluble polymer, has a good ability to form fibers, biocompatible, has a chemical resistance, and biodegradable. For further improve the quality of wound closure, this research used the method electrospining . This experiment was carried out at a distance of 8 cm with a voltage of 17 kV, 20 kV, 23 kV, 25 kV and 27 kV. Testing is done using FTIR test to determine functional groups which is formed and analysis of the microstructure using SEM. FTIR test results showed that with the addition of lendr snail does not produce new functional groups. At a voltage of 23 kV can produce a fibers with micro size with nano fiber produced is also very continuous. (author)

OpenBEM - An open source Boundary Element Method software in Acoustics

DEFF Research Database (Denmark)

Cutanda Henriquez, Vicente; Juhl, Peter Møller

2010-01-01

OpenBEM is a collection of open source programs for solving the Helmholtz Equation using the Boundary Element Method. The collection is written in Matlab by the authors and contains codes for dealing with exterior and interior problems in two or three dimensions as well as implementation of axi...... with examples of its use. Previous research results where OpenBEM was employed will be mentioned....

Aerosol based direct-write micro-additive fabrication method for sub-mm 3D metal-dielectric structures

Science.gov (United States)

Rahman, Taibur; Renaud, Luke; Heo, Deuk; Renn, Michael; Panat, Rahul

2015-10-01

The fabrication of 3D metal-dielectric structures at sub-mm length scale is highly important in order to realize low-loss passives and GHz wavelength antennas with applications in wearable and Internet-of-Things (IoT) devices. The inherent 2D nature of lithographic processes severely limits the available manufacturing routes to fabricate 3D structures. Further, the lithographic processes are subtractive and require the use of environmentally harmful chemicals. In this letter, we demonstrate an additive manufacturing method to fabricate 3D metal-dielectric structures at sub-mm length scale. A UV curable dielectric is dispensed from an Aerosol Jet system at 10-100 µm length scale and instantaneously cured to build complex 3D shapes at a length scale  <1 mm. A metal nanoparticle ink is then dispensed over the 3D dielectric using a combination of jetting action and tilted dispense head, also using the Aerosol Jet technique and at a length scale 10-100 µm, followed by the nanoparticle sintering. Simulation studies are carried out to demonstrate the feasibility of using such structures as mm-wave antennas. The manufacturing method described in this letter opens up the possibility of fabricating an entirely new class of custom-shaped 3D structures at a sub-mm length scale with potential applications in 3D antennas and passives.

Aerosol based direct-write micro-additive fabrication method for sub-mm 3D metal-dielectric structures

International Nuclear Information System (INIS)

Rahman, Taibur; Panat, Rahul; Renaud, Luke; Heo, Deuk; Renn, Michael

2015-01-01

The fabrication of 3D metal-dielectric structures at sub-mm length scale is highly important in order to realize low-loss passives and GHz wavelength antennas with applications in wearable and Internet-of-Things (IoT) devices. The inherent 2D nature of lithographic processes severely limits the available manufacturing routes to fabricate 3D structures. Further, the lithographic processes are subtractive and require the use of environmentally harmful chemicals. In this letter, we demonstrate an additive manufacturing method to fabricate 3D metal-dielectric structures at sub-mm length scale. A UV curable dielectric is dispensed from an Aerosol Jet system at 10–100 µm length scale and instantaneously cured to build complex 3D shapes at a length scale  <1 mm. A metal nanoparticle ink is then dispensed over the 3D dielectric using a combination of jetting action and tilted dispense head, also using the Aerosol Jet technique and at a length scale 10–100 µm, followed by the nanoparticle sintering. Simulation studies are carried out to demonstrate the feasibility of using such structures as mm-wave antennas. The manufacturing method described in this letter opens up the possibility of fabricating an entirely new class of custom-shaped 3D structures at a sub-mm length scale with potential applications in 3D antennas and passives. (technical note)

Qualitative zoning of groundwater for drinking purposes in Lenjan plain using GQI method through GIS

Directory of Open Access Journals (Sweden)

Amin Mohebbi Tafreshi

2017-09-01

Full Text Available Background: A new method has been presented specifically for zoning the quality of groundwater for drinking purposes; this method is the groundwater quality index (GQI method. The present research used the GQI method to qualitatively zoning of the Lenjan groundwater for drinking purposes. Methods: Three phases were applied in this research. In the first phase, working on the quality data of 38 wells within the studied plain, the raster map of quality concentration parameters, including pH, TDS, Cl, SO4, Ca, Mg, and Na parameters, was provided by interpolation using the kriging method in the ArcGIS software. In the second phase, the mentioned maps were standardized so that various bits of data can follow a common standard and scale. In the third phase, weight was applied to each standardized map, and ultimately the classification map for each parameter was drawn. The final GQI map was created by combining the mentioned classification maps. Results: The GQI values for Lenjan plain were rated from the minimum (67.48 to the maximum (90.05. The results showed an average to acceptable level of quality for drinking water. Conclusion: According to the final map, the central and southern parts of Lenjan plain, which have acceptable GQI rankings, are the best zones from which to use groundwater for drinking purposes.

A comparative study of additive and subtractive manufacturing for dental restorations.

Science.gov (United States)

Bae, Eun-Jeong; Jeong, Il-Do; Kim, Woong-Chul; Kim, Ji-Hwan

2017-08-01

Digital systems have recently found widespread application in the fabrication of dental restorations. For the clinical assessment of dental restorations fabricated digitally, it is necessary to evaluate their accuracy. However, studies of the accuracy of inlay restorations fabricated with additive manufacturing are lacking. The purpose of this in vitro study was to evaluate and compare the accuracy of inlay restorations fabricated by using recently introduced additive manufacturing with the accuracy of subtractive methods. The inlay (distal occlusal cavity) shape was fabricated using 3-dimensional image (reference data) software. Specimens were fabricated using 4 different methods (each n=10, total N=40), including 2 additive manufacturing methods, stereolithography apparatus and selective laser sintering; and 2 subtractive methods, wax and zirconia milling. Fabricated specimens were scanned using a dental scanner and then compared by overlapping reference data. The results were statistically analyzed using a 1-way analysis of variance (α=.05). Additionally, the surface morphology of 1 randomly (the first of each specimen) selected specimen from each group was evaluated using a digital microscope. The results of the overlap analysis of the dental restorations indicated that the root mean square (RMS) deviation observed in the restorations fabricated using the additive manufacturing methods were significantly different from those fabricated using the subtractive methods (Padditive manufacturing methods (P=.466). Similarly, no significant differences were found between wax and zirconia, the subtractive methods (P=.986). The observed RMS values were 106 μm for stereolithography apparatus, 113 μm for selective laser sintering, 116 μm for wax, and 119 μm for zirconia. Microscopic evaluation of the surface revealed a fine linear gap between the layers of restorations fabricated using stereolithography apparatus and a grooved hole with inconsistent weak scratches

PULP OBTAINING METHOD FOR PACKAGE PRODUCTION

Directory of Open Access Journals (Sweden)

V. V. Kuzmich

2015-01-01

Full Text Available The paper presents a new method for obtaining pulp which is used for production of cardboard, paper and package while using carbon dioxide and hydrazine hydrate and neutral-sulfite  shive cooking. Output increase of  the desired product can be explained by reduction in destruction of plant raw material carbohydrates during its cooking process. Quality improvement of the desired product (improvement in bleaching and output is attributed to the fact that usage of carbon dioxide and hydrazine contributes to provision of polysaccharide chain resistance to destruction due to the presence of  end links having structure of metasaccharinic and aldonic acids.The author has developed a new method for pulp obtaining on the basis of the executed investigations  and literature data.  СО2 and hydrazine hydrate have been used for obtaining pulp. Method invention concerns pulp obtaining and it can be used for paper and cardboard package manufacturing in pulp and paper industry.The method is to be carried in the following way: pulp-containing plant raw material is loaded into an autoclave and then aqua solution of sodium monosulfite containing hydrazine hydrate that constitutes 4–5 % of absolute dry pulp-containing raw material mass with liquid module 1:6–1:8 is supplied into the autoclave. The autoclave is closed for operation under pressure and the solution is carbonated under pressure which constitutes 5–8 % of absolute dry plant raw material (shover. Temperature is subsequently raised up to 180 °С in the space of 2 hours and cooking is carried out in the course of 4 hours. Usage of  the proposed method for shover cooking makes it possible to reduce monosulfite cooking process and improve qualitative characteristics and output of the desired product.  In addition to above mentioned fact there is a possibility to improve bleaching and final product output. 

Acid Rain Analysis by Standard Addition Titration.

Science.gov (United States)

Ophardt, Charles E.

1985-01-01

The standard addition titration is a precise and rapid method for the determination of the acidity in rain or snow samples. The method requires use of a standard buret, a pH meter, and Gran's plot to determine the equivalence point. Experimental procedures used and typical results obtained are presented. (JN)

A comprehensive analysis of Italian web pages mentioning squalene-based influenza vaccine adjuvants reveals a high prevalence of misinformation.

Science.gov (United States)

Panatto, Donatella; Amicizia, Daniela; Arata, Lucia; Lai, Piero Luigi; Gasparini, Roberto

2018-04-03

Squalene-based adjuvants have been included in influenza vaccines since 1997. Despite several advantages of adjuvanted seasonal and pandemic influenza vaccines, laypeople's perception of such formulations may be hesitant or even negative under certain circumstances. Moreover, in Italian, the term "squalene" has the same root as such common words as "shark" (squalo), "squalid" and "squalidness" that tend to have negative connotations. This study aimed to quantitatively and qualitatively analyze a representative sample of Italian web pages mentioning squalene-based adjuvants used in influenza vaccines. Every effort was made to limit the subjectivity of judgments. Eighty-four unique web pages were assessed. A high prevalence (47.6%) of pages with negative or ambiguous attitudes toward squalene-based adjuvants was established. Compared with web pages reporting balanced information on squalene-based adjuvants, those categorized as negative/ambiguous had significantly lower odds of belonging to a professional institution [adjusted odds ratio (aOR) = 0.12, p = .004], and significantly higher odds of containing pictures (aOR = 1.91, p = .034) and being more readable (aOR = 1.34, p = .006). Some differences in wording between positive/neutral and negative/ambiguous web pages were also observed. The most common scientifically unsound claims concerned safety issues and, in particular, claims linking squalene-based adjuvants to the Gulf War Syndrome and autoimmune disorders. Italian users searching the web for information on vaccine adjuvants have a high likelihood of finding unbalanced and misleading material. Information provided by institutional websites should be not only evidence-based but also carefully targeted towards laypeople. Conversely, authors writing for non-institutional websites should avoid sensationalism and provide their readers with more balanced information.

A screening method based on UV-Visible spectroscopy and multivariate analysis to assess addition of filler juices and water to pomegranate juices.

Science.gov (United States)

Boggia, Raffaella; Casolino, Maria Chiara; Hysenaj, Vilma; Oliveri, Paolo; Zunin, Paola

2013-10-15

Consumer demand for pomegranate juice has considerably grown, during the last years, for its potential health benefits. Since it is an expensive functional food, cheaper fruit juices addition (i.e., grape and apple juices) or its simple dilution, or polyphenols subtraction are deceptively used. At present, time-consuming analyses are used to control the quality of this product. Furthermore these analyses are expensive and require well-trained analysts. Thus, the purpose of this study was to propose a high-speed and easy-to-use shortcut. Based on UV-VIS spectroscopy and chemometrics, a screening method is proposed to quickly screening some common fillers of pomegranate juice that could decrease the antiradical scavenging capacity of pure products. The analytical method was applied to laboratory prepared juices, to commercial juices and to representative experimental mixtures at different levels of water and filler juices. The outcomes were evaluated by means of multivariate exploratory analysis. The results indicate that the proposed strategy can be a useful screening tool to assess addition of filler juices and water to pomegranate juices. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effect of Sodium Lauryl Sulfate-Fumaric Acid Coupled Addition on the In Vitro Rumen Fermentation with Special Regard to Methanogenesis

Directory of Open Access Journals (Sweden)

M. A. Abdl-Rahman

2010-01-01

Full Text Available The aim of the current study was to evaluate the effect of sodium lauryl sulfate-fumaric acid coupled addition on in vitro methangenesis and rumen fermentation. Evaluation was carried out using in vitro gas production technique. Ruminal contents were collected from five steers immediately after slaughtering and used for preparation of inoculums of mixed rumen microorganisms. Rumen fluid was then mixed with the basal diet of steers and used to generate four treatments, negative control (no additives, sodium lauryl sulfate (SLS treated, fumaric acid treated, and SLS-fumaric acid coupled addition treated. The results revealed that, relative to control, efficiency in reduction of methanogenesis was as follows: coupled addition > SLS-addition > fumaric acid addition. Both SLS-addition and SLS-fumaric acid coupled addition demonstrated a decremental effect on ammonia nitrogen (NH3–N, total short chain volatile fatty acids (SCVFAs concentrations and the amount of substrate degraded, and an increment effect on microbial mass and microbial yield (YATP. Nevertheless, fumaric acid did not alter any of the previously mentioned parameters but induced a decremental effect on NH3–N. Furthermore, both fumaric acid and SLS-fumaric acid coupled addition increased propionate at the expense of acetate and butyrate, while, defaunation increased acetate at the expense of propionate and butyrate. The pH value was decreased by all treatments relative to control, while, cellulase activity did not differ by different treatments. The current study can be promising strategies for suppressing ruminal methane emissions and improving ruminants feed efficiency.

Effect of sodium lauryl sulfate-fumaric Acid coupled addition on the in vitro rumen fermentation with special regard to methanogenesis.

Science.gov (United States)

Abdl-Rahman, M A; Sawiress, F A R; Abd El-Aty, A M

2010-01-01

The aim of the current study was to evaluate the effect of sodium lauryl sulfate-fumaric acid coupled addition on in vitro methangenesis and rumen fermentation. Evaluation was carried out using in vitro gas production technique. Ruminal contents were collected from five steers immediately after slaughtering and used for preparation of inoculums of mixed rumen microorganisms. Rumen fluid was then mixed with the basal diet of steers and used to generate four treatments, negative control (no additives), sodium lauryl sulfate (SLS) treated, fumaric acid treated, and SLS-fumaric acid coupled addition treated. The results revealed that, relative to control, efficiency in reduction of methanogenesis was as follows: coupled addition > SLS-addition > fumaric acid addition. Both SLS-addition and SLS-fumaric acid coupled addition demonstrated a decremental effect on ammonia nitrogen (NH(3)-N), total short chain volatile fatty acids (SCVFAs) concentrations and the amount of substrate degraded, and an increment effect on microbial mass and microbial yield (Y(ATP)). Nevertheless, fumaric acid did not alter any of the previously mentioned parameters but induced a decremental effect on NH(3)-N. Furthermore, both fumaric acid and SLS-fumaric acid coupled addition increased propionate at the expense of acetate and butyrate, while, defaunation increased acetate at the expense of propionate and butyrate. The pH value was decreased by all treatments relative to control, while, cellulase activity did not differ by different treatments. The current study can be promising strategies for suppressing ruminal methane emissions and improving ruminants feed efficiency.

Additive manufacturing in maxillofacial reconstruction

Directory of Open Access Journals (Sweden)

Dincă Luciana Laura

2017-01-01

Full Text Available In this paper the benefits of using additive manufacturing technologies in maxillofacial reconstruction are highlighted. Based on a real clinical case, the paper describes the manufacture of an implant prototype replacing the right zygomatic bone and a part of maxilla using additive manufacturing technologies. The face is the most expressive part of the human body that makes us unique. It was shown that the maxillofacial prostheses help to improve the psychological state of patients affected by, because low self esteem feeling appears commonly to this patients with the facial defects. The aim of this paper is to show how using additive manufacturing technologies methods within this research, the producing a surgical model will help surgeon to improve the pre-operative planning. For this we used additive manufacturing technologies such as Stereolitography to achieve the biomodel and FDM-fused deposition modelling to obtain a prototype model because these technologies make it possible to obtain prosthesis according to the physical and mechanical requirements of the region of implantation.

Characterization of heterologously expressed transporter genes by patch- and voltage-clamp methods: Application to cyclic nucleotide-dependent responses

KAUST Repository

Lemtiri-Chlieh, Fouad

2013-09-03

The application of patch- and voltage-clamp methods to study ion transport can be limited by many hurdles: the size of the cells to be patched and/or stabbed, the subcellular localization of the molecule of interest, and its density of expression that could be too low even in their own native environment. Functional expression of genes using recombinant DNA technology not only overcomes those hurdles but also affords additional and elegant investigations such as single-point mutation studies and subunit associations/regulations. In this chapter, we give a step-by-step description of two electrophysiological methods, patch clamp and two-electrode voltage clamp (TEVC), that are routinely used in combination with heterologous gene expression to assist researchers interested in the identification and characterization of ion transporters. We describe how to (1) obtain and maintain the cells suitable for the use with each of the above-mentioned methods (i.e., HEK-293 cells and yeast spheroplasts to use with the patch-clamp methodology and Xenopus laevis oocytes with TEVC), (2) transfect/inject them with the gene of interest, and (3) record ion transport activities. © Springer Science+Business Media New York 2013.

Characterization of heterologously expressed transporter genes by patch- and voltage-clamp methods: Application to cyclic nucleotide-dependent responses

KAUST Repository

Lemtiri-Chlieh, Fouad; Ali, Rashid Ayesha

2013-01-01

The application of patch- and voltage-clamp methods to study ion transport can be limited by many hurdles: the size of the cells to be patched and/or stabbed, the subcellular localization of the molecule of interest, and its density of expression that could be too low even in their own native environment. Functional expression of genes using recombinant DNA technology not only overcomes those hurdles but also affords additional and elegant investigations such as single-point mutation studies and subunit associations/regulations. In this chapter, we give a step-by-step description of two electrophysiological methods, patch clamp and two-electrode voltage clamp (TEVC), that are routinely used in combination with heterologous gene expression to assist researchers interested in the identification and characterization of ion transporters. We describe how to (1) obtain and maintain the cells suitable for the use with each of the above-mentioned methods (i.e., HEK-293 cells and yeast spheroplasts to use with the patch-clamp methodology and Xenopus laevis oocytes with TEVC), (2) transfect/inject them with the gene of interest, and (3) record ion transport activities. © Springer Science+Business Media New York 2013.

An Additional Method for Analyzing the Reversible Inhibition of an 
Enzyme Using Acid Phosphatase as a Model.

Science.gov (United States)

Baumhardt, Jordan M; Dorsey, Benjamin M; McLauchlan, Craig C; Jones, Marjorie A

2015-08-01

Using wheat germ acid phosphatase and sodium orthovanadate as a competitive inhibitor, a novel method for analyzing reversible inhibition was carried out. Our alternative approach involves plotting the initial velocity at which product is formed as a function of the ratio of substrate concentration to inhibitor concentration at a constant enzyme concentration and constant assay conditions. The concept of initial concentrations driving equilibrium leads to the chosen axes. Three apparent constants can be derived from this plot: K max , K min , and K inflect . K max and K min represent the substrate to inhibitor concentration ratio for complete inhibition and minimal inhibition, respectively. K inflect represents the substrate to inhibitor concentration ratio at which the enzyme-substrate complex is equal to the inhibitory complex. These constants can be interpolated from the graph or calculated using the first and second derivative of the plot. We conclude that a steeper slope and a shift of the line to the right (increased x-axis values) would indicate a better inhibitor. Since initial velocity is not a linear function of the substrate/inhibitor ratio, this means that inhibition changes more quickly with the change in the [S]/ [I] ratio. When preincubating the enzyme with substrate before the addition of inhibitor, preincubating the enzyme with inhibitor before the addition of substrate or with concurrent addition of both substrate and inhibitor, modest changes in the slopes and y-intercepts were obtained. This plot appears useful for known competitive and non-competitive inhibitors and may have general applicability.

Multiple Linkage Disequilibrium Mapping Methods to Validate Additive Quantitative Trait Loci in Korean Native Cattle (Hanwoo

Directory of Open Access Journals (Sweden)

Yi Li

2015-07-01

Full Text Available The efficiency of genome-wide association analysis (GWAS depends on power of detection for quantitative trait loci (QTL and precision for QTL mapping. In this study, three different strategies for GWAS were applied to detect QTL for carcass quality traits in the Korean cattle, Hanwoo; a linkage disequilibrium single locus regression method (LDRM, a combined linkage and linkage disequilibrium analysis (LDLA and a BayesCπ approach. The phenotypes of 486 steers were collected for weaning weight (WWT, yearling weight (YWT, carcass weight (CWT, backfat thickness (BFT, longissimus dorsi muscle area, and marbling score (Marb. Also the genotype data for the steers and their sires were scored with the Illumina bovine 50K single nucleotide polymorphism (SNP chips. For the two former GWAS methods, threshold values were set at false discovery rate <0.01 on a chromosome-wide level, while a cut-off threshold value was set in the latter model, such that the top five windows, each of which comprised 10 adjacent SNPs, were chosen with significant variation for the phenotype. Four major additive QTL from these three methods had high concordance found in 64.1 to 64.9Mb for Bos taurus autosome (BTA 7 for WWT, 24.3 to 25.4Mb for BTA14 for CWT, 0.5 to 1.5Mb for BTA6 for BFT and 26.3 to 33.4Mb for BTA29 for BFT. Several candidate genes (i.e. glutamate receptor, ionotropic, ampa 1 [GRIA1], family with sequence similarity 110, member B [FAM110B], and thymocyte selection-associated high mobility group box [TOX] may be identified close to these QTL. Our result suggests that the use of different linkage disequilibrium mapping approaches can provide more reliable chromosome regions to further pinpoint DNA makers or causative genes in these regions.

Magnetic resonance tomography - an additive method complementary to ultrasonographic diagnosis of fetal malformations

International Nuclear Information System (INIS)

Bloechle, M.; Bollmann, R.; Zienert, A.; Kalache, K.; Koerner, H.; Tennstedt, C.; Ivanow, S.

1992-01-01

A case of prenatal sonographic diagnosis of polycystic renal degeneration is reported in this paper. With oligophydramnion established, the extent of the malformation could not be reliable diagnosed by means of sonography. It was also not possible to determine safely whether both kidneys were affected by malformation or if one possibly intact kidney was superimposed by one with dysplasia. In addition, the urinary bladder could not be sonographically delineated with reliability. Magnetic resonance tomography (MRT) was thus performed as an additional modality to complete the fetal diagnosis. The results thus obtained and the role of MRI in prenatal diagnosis and therapy are discussed. (orig.) [de

Method for sustaining microorganism culture in syngas fermentation process in decreased concentration or absence of various substrates

Science.gov (United States)

Adams, Stephen S.; Scott, Syrona; Ko, Ching-Whan

2015-05-19

The present invention relates to methods for sustaining microorganism culture in a syngas fermentation reactor in decreased concentration or absence of various substrates comprising: adding carbon dioxide and optionally alcohol; maintaining free acetic acid concentrations; and performing the above mentioned steps within specified time.

Phosphate analysis of natural sausage casings preserved in brines with phosphate additives as inactivating agent - Method validation.

Science.gov (United States)

Wijnker, J J; Tjeerdsma-van Bokhoven, J L M; Veldhuizen, E J A

2009-01-01

Certain phosphates have been identified as suitable additives for the improvement of the microbial and mechanical properties of processed natural sausage casings. When mixed with NaCl (sodium chloride) and used under specific treatment and storage conditions, these phosphates are found to prevent the spread of foot-and-mouth disease and classical swine fever via treated casings. The commercially available Quantichrom™ phosphate assay kit has been evaluated as to whether it can serve as a reliable and low-tech method for routine analysis of casings treated with phosphate. The outcome of this study indicates that this particular assay kit has sufficient sensitivity to qualitatively determine the presence of phosphate in treated casings without interference of naturally occurring phosphate in salt used for brines in which casings are preserved.

Developing design methods of concrete mix with microsilica additives for road construction

Science.gov (United States)

Dmitrienko, Vladimir; Shrivel, Igor; Kokunko, Irina; Pashkova, Olga

2017-10-01

Based on the laboratory test results, regression equations having standard cone and concrete strength, to determine the available amount of cement, water and microsilica were obtained. The joint solution of these equations allowed the researchers to develop the algorithm of designing heavy concrete compositions with microsilica additives for road construction.

The influence of kind of coating additive on the compressive strength of RCA-based concrete prepared by triple-mixing method

Science.gov (United States)

Urban, K.; Sicakova, A.

2017-10-01

The paper deals with the use of alternative powder additives (fly ash and fine fraction of recycled concrete) to improve the recycled concrete aggregate and this occurs directly in the concrete mixing process. Specific mixing process (triple mixing method) is applied as it is favourable for this goal. Results of compressive strength after 2 and 28 days of hardening are given. Generally, using powder additives for coating the coarse recycled concrete aggregate in the first stage of triple mixing resulted in decrease of compressive strength, comparing the cement. There is no very important difference between samples based on recycled concrete aggregate and those based on natural aggregate as far as the cement is used for coating. When using both the fly ash and recycled concrete powder, the kind of aggregate causes more significant differences in compressive strength, with the values of those based on the recycled concrete aggregate being worse.

Influence of additives on the increase of the heating value of Bayah’s coal with upgrading brown coal (UBC) method

International Nuclear Information System (INIS)

Heriyanto, Heri; Widya Ernayati, K.; Umam, Chairul; Margareta, Nita

2015-01-01

UBC (upgrading brown coal) is a method of improving the quality of coal by using oil as an additive. Through processing in the oil media, not just the calories that increase, but there is also water repellent properties and a decrease in the tendency of spontaneous combustion of coal products produced. The results showed a decrease in the water levels of natural coal bayah reached 69%, increase in calorific value reached 21.2%. Increased caloric value and reduced water content caused by the water molecules on replacing seal the pores of coal by oil and atoms C on the oil that is bound to increase the percentage of coal carbon. As a result of this experiment is, the produced coal has better calorific value, the increasing of this new calorific value up to 23.8% with the additive waste lubricant, and the moisture content reduced up to 69.45%

Influence of additives on the increase of the heating value of Bayah’s coal with upgrading brown coal (UBC) method

Energy Technology Data Exchange (ETDEWEB)

Heriyanto, Heri [Chemical Engineering of University Sultan AgengTirtayasa, Indonesia Email: herfais@yahoo.com (Indonesia); Widya Ernayati, K.; Umam, Chairul; Margareta, Nita

2015-12-29

UBC (upgrading brown coal) is a method of improving the quality of coal by using oil as an additive. Through processing in the oil media, not just the calories that increase, but there is also water repellent properties and a decrease in the tendency of spontaneous combustion of coal products produced. The results showed a decrease in the water levels of natural coal bayah reached 69%, increase in calorific value reached 21.2%. Increased caloric value and reduced water content caused by the water molecules on replacing seal the pores of coal by oil and atoms C on the oil that is bound to increase the percentage of coal carbon. As a result of this experiment is, the produced coal has better calorific value, the increasing of this new calorific value up to 23.8% with the additive waste lubricant, and the moisture content reduced up to 69.45%.

Inhibition of calcium carbonate crystal growth by organic additives using the constant composition method in conditions of recirculating cooling circuits

Science.gov (United States)

Chhim, Norinda; Kharbachi, Chams; Neveux, Thibaut; Bouteleux, Céline; Teychené, Sébastien; Biscans, Béatrice

2017-08-01

The cooling circuits used in power plants are subject to mineral crystallization which can cause scaling on the surfaces of equipment and construction materials reducing their heat exchange efficiency. Precipitated calcium carbonate is the predominant mineral scale commonly observed in cooling systems. Supersaturation is the key parameter controlling the nucleation and growth of calcite in these systems. The present work focuses on the precipitation of calcite using the constant composition method at constant supersaturation, through controlled addition of reactants to a semi-batch crystallizer, in order to maintain constant solution pH. The determination of the thermodynamic driving force (supersaturation) was based on the relevant chemical equilibria, total alkalinity and calculation of the activity coefficients. Calcite crystallization rates were derived from the experiments performed at supersaturation levels similar to those found in industrial station cooling circuits. Several types of seeds particles were added into the aqueous solution to mimic natural river water conditions in terms of suspended particulate matters content, typically: calcite, silica or illite particles. The effect of citric and copolycarboxylic additive inhibitors added to the aqueous solution was studied. The calcium carbonate growth rate was reduced by 38.6% in the presence of the citric additive and a reduction of 92.7% was observed when the copolycarboxylic additive was used under identical experimental conditions. These results are explained by the location of the adsorbed inhibitor at the crystal surface and by the degree of chemical bonding to the surface.

An Inventory of Methods for the Assessment of Additive Increased Addictiveness of Tobacco Products.

Science.gov (United States)

van de Nobelen, Suzanne; Kienhuis, Anne S; Talhout, Reinskje

2016-07-01

Cigarettes and other forms of tobacco contain the addictive drug nicotine. Other components, either naturally occurring in tobacco or additives that are intentionally added during the manufacturing process, may add to the addictiveness of tobacco products. As such, these components can make cigarette smokers more easily and heavily dependent.Efforts to regulate tobacco product dependence are emerging globally. Additives that increase tobacco dependence will be prohibited under the new European Tobacco Product Directive. This article provides guidelines and recommendations for developing a regulatory strategy for assessment of increase in tobacco dependence due to additives. Relevant scientific literature is summarized and criteria and experimental studies that can define increased dependence of tobacco products are described. Natural tobacco smoke is a very complex matrix of components, therefore analysis of the contribution of an additive or a combination of additives to the level of dependence on this product is challenging. We propose to combine different type of studies analyzing overall tobacco product dependence potential and the functioning of additives in relation to nicotine. By using a combination of techniques, changes associated with nicotine dependence such as behavioral, physiological, and neurochemical alterations can be examined to provide sufficient information.Research needs and knowledge gaps will be discussed and recommendations will be made to translate current knowledge into legislation. As such, this article aids in implementation of the Tobacco Product Directive, as well as help enable regulators and researchers worldwide to develop standards to reduce dependence on tobacco products. This article provides an overall view on how to assess tobacco product constituents for their potential contribution to use and dependence. It provides guidelines that help enable regulators worldwide to develop standards to reduce dependence on tobacco products

Additionality of global benefits and financial additionality in the context of the AIJ negotiations

Energy Technology Data Exchange (ETDEWEB)

Puhl, I.

1996-12-31

The Conference of the Party at their first meeting (COP1) took a decision regarding criteria for joint implementation as indicated in Art. 4.2 (a) of the FCCC which established a pilot phase for activities implemented jointly (AIJ) under the pilot phase. Besides some more technical issues this decision specified that such measures should bring about real, measurable and long-term environmental benefits related to the mitigation of climate change that would not have occurred in the absence of such activities. It also established that the financing of AIJ shall be additional to the financial obligations of developed country parties. These two requirements are called the additionality criteria for AIJ. The first refers to the realness of GHG emission abatement (which means reduction compared to a baseline) whereas the second describes that funds earmarked for AIJ have no other objective (i.e. profit making, export promotion) but to reduce GHG emissions to avoid the free-riding of investors and subsequently developed country parties. The reporting framework as well as the reporting requirements under national programs do not specify further the two types of additionality and even though research focuses on issues like baseline determination there has been no attempt so far to identify approaches which contribute towards defining strict and practicable methods and guidelines to frame additionality criteria. The first FCCC assessment of pilot project reporting revealed that in the reporting of activities, emissions additionality often remained unclear, especially in cases where AIJ was only a portion of an existing or already planned project, and that there is a point about how to account for financial additionality. It subsequently proposed to develop a uniform approach to baseline determination and the assessment of emission (reduction) additionality and financial additionality.

Determination of Mn, Fe, and Cu in chemically-treated wood pulps by the XRF addition method

Energy Technology Data Exchange (ETDEWEB)

Raemoe, J.; Klasila, T.; Piepponen, S. [VTT Chemical Technology (Finland); Sillanpaeae, M. [Oulu Univ. (Finland)

2001-08-01

A rapid X-ray fluorescence addition method has been developed for quantification of the technically most important metals in wood pulp matrix (Mn, Fe, and Cu). Pretreatment consisted of just two steps: first, acid was added to the sample to achieve homogeneous distribution of the metals; the pulp was then pressed lightly on to Mylar film. Total analysis time was less than 10 min. The concentration range investigated was up to 15 mg kg{sup -1} for Mn and up to 5 mg kg{sup -1} for Fe and Cu. Metal concentrations in Scandinavian pulps are not expected to exceed these amounts. The quantification limit was 2 mg kg{sup -1} for all three metals. The reproducibilities and repeatabilities were concentration-dependent and varied between 3 and 19% and between 1 and 17%, respectively. The squares of the linear correlation coefficients between measured intensity and added metal concentration were 0.994, 0.950, and 0.932 for Mn, Fe, and Cu, respectively. (orig.)

Searching for Suicide Methods: Accessibility of Information About Helium as a Method of Suicide on the Internet.

Science.gov (United States)

Gunnell, David; Derges, Jane; Chang, Shu-Sen; Biddle, Lucy

2015-01-01

Helium gas suicides have increased in England and Wales; easy-to-access descriptions of this method on the Internet may have contributed to this rise. To investigate the availability of information on using helium as a method of suicide and trends in searching about this method on the Internet. We analyzed trends in (a) Google searching (2004-2014) and (b) hits on a Wikipedia article describing helium as a method of suicide (2013-2014). We also investigated the extent to which helium was described as a method of suicide on web pages and discussion forums identified via Google. We found no evidence of rises in Internet searching about suicide using helium. News stories about helium suicides were associated with increased search activity. The Wikipedia article may have been temporarily altered to increase awareness of suicide using helium around the time of a celebrity suicide. Approximately one third of the links retrieved using Google searches for suicide methods mentioned helium. Information about helium as a suicide method is readily available on the Internet; the Wikipedia article describing its use was highly accessed following celebrity suicides. Availability of online information about this method may contribute to rises in helium suicides.

Review: Helmut Kromrey (2006. Empirische Sozialforschung. Modelle und Methoden der standardisierten Datenerhebung und Datenauswertung [Social Research Methods. Models and Methods of Standardized Data Collection and Data Analysis

Directory of Open Access Journals (Sweden)

Udo Kuckartz

2008-01-01

Full Text Available In the new edition of his textbook, KROMREY outlines the basic principles of "traditional" empirical social research. The 650 pages of the book address the foundations of scientific theory and methods within empirical research. There are also extensive explanations of the most important methods of data collection (content analysis, observation, survey and of statistical analyses of data. This book would be a very suitable textbook for introductory university courses in the methods of empirical social research. The text includes many examples and is written in a very understandable style. Qualitative research methods are only mentioned marginally in the "Alternative Research Paradigms" section. URN: urn:nbn:de:0114-fqs0801240

An analysis of the additional fission product release phenomena

International Nuclear Information System (INIS)

Takeda, Tsuneo; Nagai, Hitoshi

1978-09-01

The additional fission product release behavior through a defect hole on the cladding of fuel rods has been studied qualitatively with a computer program CODAC-ARFP. The additional fission product release phenomena are described as qualitative evaluation. The additional fission product release behavior in coolant temperature and pressure fluctuations and in reactor start-up and shut-down depends on coolant water flow behavior into and from the free space of fuel rods through a defect hole. Based on the results of evaluations, the experimental results with an inpile water loop OWL-1 are described in detail. The estimation methods of fission product quantity in the free space and fission product release ratio (quantity released into the coolant/quantity in the free space before beginning of release) are necessary for analysis of the fission product release behavior; the estimation method of water flow through a defect hole is also necessary. In development of the above estimation methods, outpile and capsule experiments supporting the additional fission product release experiments are required. (author)

PTFE Additive and Re-annealing Effect on Thermoluminescence Response of CaSO4:Dy Derived from Co-precipitation Method

Science.gov (United States)

Nuraeni, Nunung; Dwi Septianto, Ricky; Iskandar, Ferry; Haryanto, Freddy; Waris, Abdul; Hiswara, Eri

2017-07-01

Effect of re-annealing treatment in thermoluminescence response of thermoluminescent dosimeter (TLD) CaSO4:Dy and CaSO4:Dy with PTFE (Polytetrafluoroethylene) addition was investigated. CaSO4:Dy was prepared by a co-precipitation method. The PTFE was added before re-annealing treatment which the mass ratio of CaSO4:Dy and PTFE was fixed to 2:3. The re-annealing treatments of the samples were done at temperature 700 °C for 1 hr. The obtained samples were characterized using a Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) to observe the molecule bonding in sample and crystal properties, respectively. From the experimental results, it was observed that the thermoluminescence intensity of CaSO4:Dy, CaSO4:Dy re-annealed at 700 °C, and CaSO4:Dy + PTFE re-annealed at 700 °C are 57.03, 75.15, and 1191.11 nC, respectively. The intensity of 700 °C-re-annealed CaSO4:Dy increased significantly after PTFE addition.

Noise thermometry - a new temperature measuring method

International Nuclear Information System (INIS)

Brixy, H.; Hecker, R.; Rittinghaus, K.F.

1975-01-01

The thermal Johnson-Niquist noise is the basis of noise thermometry. This temperature measuring method is, e.g., of interest insofar as the noise thermometer gives absolute values as a primary thermometer and is in principle extensively independent of environmental influences and material properties. The resistance values of the measuring probe are about 10 Ohm to a few kOhm. The demands of electronics are high, the self-noise of the measuring apparatus must be as small as possible; a comparative measuring method is advantageous. 1 to 2,500 K are given as a possible temperature range. An accuracy of 0.1% could be achieved in laboratory measurements. Temperature measurements to be used in operation in a few nuclear reactors are mentioned. (HP/LH) [de

Comparative study of key exchange and authentication methods in application, transport and network level security mechanisms

Science.gov (United States)

Fathirad, Iraj; Devlin, John; Jiang, Frank

2012-09-01

The key-exchange and authentication are two crucial elements of any network security mechanism. IPsec, SSL/TLS, PGP and S/MIME are well-known security approaches in providing security service to network, transport and application layers; these protocols use different methods (based on their requirements) to establish keying materials and authenticates key-negotiation and participated parties. This paper studies and compares the authenticated key negotiation methods in mentioned protocols.

Protocol for ADDITION-PRO

DEFF Research Database (Denmark)

Johansen, Nanna Borup; Hansen, Anne-Louise Smidt; Jensen, Troels M

2012-01-01

disease and microvascular diabetic complications. We also require a better understanding of the mechanisms that underlie and drive early changes in cardiometabolic physiology. The ADDITION-PRO study was designed to address these issues among individuals at different levels of diabetes risk recruited from...... Danish primary care. METHODS/DESIGN: ADDITION-PRO is a population-based, longitudinal cohort study of individuals at high risk for diabetes. 16,136 eligible individuals were identified at high risk following participation in a stepwise screening programme in Danish general practice between 2001 and 2006....... All individuals with impaired glucose regulation at screening, those who developed diabetes following screening, and a random sub-sample of those at lower levels of diabetes risk were invited to attend a follow-up health assessment in 2009-2011 (n=4,188), of whom 2,082 (50%) attended. The health...

Text-mining as a methodology to assess eating disorder-relevant factors: Comparing mentions of fitness tracking technology across online communities.

Science.gov (United States)

McCaig, Duncan; Bhatia, Sudeep; Elliott, Mark T; Walasek, Lukasz; Meyer, Caroline

2018-05-07

Text-mining offers a technique to identify and extract information from a large corpus of textual data. As an example, this study presents the application of text-mining to assess and compare interest in fitness tracking technology across eating disorder and health-related online communities. A list of fitness tracking technology terms was developed, and communities (i.e., 'subreddits') on a large online discussion platform (Reddit) were compared regarding the frequency with which these terms occurred. The corpus used in this study comprised all comments posted between May 2015 and January 2018 (inclusive) on six subreddits-three eating disorder-related, and three relating to either fitness, weight-management, or nutrition. All comments relating to the same 'thread' (i.e., conversation) were concatenated, and formed the cases used in this study (N = 377,276). Within the eating disorder-related subreddits, the findings indicated that a 'pro-eating disorder' subreddit, which is less recovery focused than the other eating disorder subreddits, had the highest frequency of fitness tracker terms. Across all subreddits, the weight-management subreddit had the highest frequency of the fitness tracker terms' occurrence, and MyFitnessPal was the most frequently mentioned fitness tracker. The technique exemplified here can potentially be used to assess group differences to identify at-risk populations, generate and explore clinically relevant research questions in populations who are difficult to recruit, and scope an area for which there is little extant literature. The technique also facilitates methodological triangulation of research findings obtained through more 'traditional' techniques, such as surveys or interviews. © 2018 Wiley Periodicals, Inc.

Additive manufacturing of RF absorbers

Science.gov (United States)

Mills, Matthew S.

The ability of additive manufacturing techniques to fabricate integrated electromagnetic absorbers tuned for specific radio frequency bands within structural composites allows for unique combinations of mechanical and electromagnetic properties. These composites and films can be used for RF shielding of sensitive electromagnetic components through in-plane and out-of-plane RF absorption. Structural composites are a common building block of many commercial platforms. These platforms may be placed in situations in which there is a need for embedded RF absorbing properties along with structural properties. Instead of adding radar absorbing treatments to the external surface of existing structures, which adds increased size, weight and cost; it could prove to be advantageous to integrate the microwave absorbing properties directly into the composite during the fabrication process. In this thesis, a method based on additive manufacturing techniques of composites structures with prescribed electromagnetic loss, within the frequency range 1 to 26GHz, is presented. This method utilizes screen printing and nScrypt micro dispensing to pattern a carbon based ink onto low loss substrates. The materials chosen for this study will be presented, and the fabrication technique that these materials went through to create RF absorbing structures will be described. The calibration methods used, the modeling of the RF structures, and the applications in which this technology can be utilized will also be presented.

Franchising as a method of entry to the market

OpenAIRE

Vargovčíková, Lucie

2011-01-01

The subject of presented bachelor thesis is Franchising as a method of entry to the market. The first part of this thesis deals with characteristics of franchising such as the definition of franchising and its advantages and disadvantages for both parties involved. Then there is also provided the current situation of franchising in the Czech Republic. The second part deals with entry into the market by franchising. In this section franchise agreement is mainly mentioned, how to start a franch...

Bearing-only SLAM: comparison between probabilistic and deterministic methods

OpenAIRE

Joly , Cyril; Rives , Patrick

2008-01-01

This work deals with the problem of simultaneous localization and mapping (SLAM). Classical methods for solving the SLAM problem are based on the Extended Kalman Filter (EKF-SLAM) or particle filter (FastSLAM). These kinds of algorithms allow on-line solving but could be inconsistent. In this report, the above-mentioned algorithms are not studied but global ones. Global approaches need all measurements from the initial step to the final step in order to compute the trajectory of the robot and...

Non-additive Effects in Genomic Selection

Directory of Open Access Journals (Sweden)

Luis Varona

2018-03-01

Full Text Available In the last decade, genomic selection has become a standard in the genetic evaluation of livestock populations. However, most procedures for the implementation of genomic selection only consider the additive effects associated with SNP (Single Nucleotide Polymorphism markers used to calculate the prediction of the breeding values of candidates for selection. Nevertheless, the availability of estimates of non-additive effects is of interest because: (i they contribute to an increase in the accuracy of the prediction of breeding values and the genetic response; (ii they allow the definition of mate allocation procedures between candidates for selection; and (iii they can be used to enhance non-additive genetic variation through the definition of appropriate crossbreeding or purebred breeding schemes. This study presents a review of methods for the incorporation of non-additive genetic effects into genomic selection procedures and their potential applications in the prediction of future performance, mate allocation, crossbreeding, and purebred selection. The work concludes with a brief outline of some ideas for future lines of that may help the standard inclusion of non-additive effects in genomic selection.

Superconductor technology opens up new technical methods

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

Medical and industrial applications of nuclear magnetic resonance are discussed. Uses of supercooled magnetic separators for water purification are referred to. The possibility of energy storage in superconducting coils is mentioned and superconductivity for magnetic containment in fusion experiments is noted. Details are given of the construction of superconducting cables. The LCT (large coil task) project with European, Japanese and American participation is also mentioned.

Detection of honey adulteration using HPLC method

Directory of Open Access Journals (Sweden)

Olga Cwiková

2015-10-01

We have further assessed whether honey samples comply with legislative requirements relating to this product or consumer misleading practices take place. Our analysed samples often lacked indication whether it is a floral honey or honeydew honey; this information was missing in eight out of 21 samples. Samples 5 and 9 did not mention the name of manufacturer. Sample 10 did not mention the country of origin.

Noise variance analysis using a flat panel x-ray detector: A method for additive noise assessment with application to breast CT applications

Energy Technology Data Exchange (ETDEWEB)

Yang Kai; Huang, Shih-Ying; Packard, Nathan J.; Boone, John M. [Department of Radiology, University of California, Davis Medical Center, 4860 Y Street, Suite 3100 Ellison Building, Sacramento, California 95817 (United States); Department of Radiology, University of California, Davis Medical Center, 4860 Y Street, Suite 3100 Ellison Building, Sacramento, California 95817 (United States) and Department of Biomedical Engineering, University of California, Davis, Davis, California, 95616 (United States)

2010-07-15

Purpose: A simplified linear model approach was proposed to accurately model the response of a flat panel detector used for breast CT (bCT). Methods: Individual detector pixel mean and variance were measured from bCT projection images acquired both in air and with a polyethylene cylinder, with the detector operating in both fixed low gain and dynamic gain mode. Once the coefficients of the linear model are determined, the fractional additive noise can be used as a quantitative metric to evaluate the system's efficiency in utilizing x-ray photons, including the performance of different gain modes of the detector. Results: Fractional additive noise increases as the object thickness increases or as the radiation dose to the detector decreases. For bCT scan techniques on the UC Davis prototype scanner (80 kVp, 500 views total, 30 frames/s), in the low gain mode, additive noise contributes 21% of the total pixel noise variance for a 10 cm object and 44% for a 17 cm object. With the dynamic gain mode, additive noise only represents approximately 2.6% of the total pixel noise variance for a 10 cm object and 7.3% for a 17 cm object. Conclusions: The existence of the signal-independent additive noise is the primary cause for a quadratic relationship between bCT noise variance and the inverse of radiation dose at the detector. With the knowledge of the additive noise contribution to experimentally acquired images, system modifications can be made to reduce the impact of additive noise and improve the quantum noise efficiency of the bCT system.

Additively Manufactured Multi-Material Insert, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Parabilis Space Technologies is pleased to propose development of a novel additive manufacturing method which enables the use of multiple dissimilar materials in an...

The narrow-band imaging examination method in otorhinolaryngology

Directory of Open Access Journals (Sweden)

Robert Šifrer

2013-10-01

Full Text Available Early diagnostics could improve the prognosis of patients with squamous-cell carcinomas of the head and neck. Narrow-Band Imaging (NBI is the latest examination method in the group of biologic endoscopies. NBI improves the distinction between malignant and benign mucosal lesions. Early suspect oncologic lesions that may otherwise be missed by normal white light illumination can also be diagnosed. The biggest benefit of NBI technology is achieved by using it together with a HDTV camera that enables better contrast and higher resolution. NBI is based on better imaging of superficial mucosal vasculature. The biologic potential of mucosal lesions could be predicted from vascular changes. The colour of normal mucosa under NBI is blue and green and the vessels show no pathological features. Well-demarcated brownish areas and scattered thick dark spots and abnormal winding and branching out of vessels on the mucosa are all oncologically suspicious features. Authors report the experience from literature on the use of NBI to identify carcinomas of the oral cavity, epipharynx, oropharynx, hypopharynx and larynx and evaluation of unknown primaries. In addition, the literature reports the benefit of NBI in identifying early stage carcinomas in previously irradiated patients. Persistence and recurrence of carcinoma and the development of new primary tumour could easily be missed by using only standard white-light illumination. The method proved to be highly sensitive and specific for predicting malignant changes in the above-mentioned circumstances. Authors report their own experience with NBI technology as well. For further improvement of the method, new technologic development is expected to enable the connection of NBI and HDTV with flexible endoscopes.

Additives in crude oil. A new attempt to prevent boilover; Additive im Rohoel. Ein neuer Ansatz zur Vermeidung eines Boilover

Energy Technology Data Exchange (ETDEWEB)

Gosewinkel, Martin; Dworschak, Rene [INBUREX Consulting GmbH, Hamm (Germany)

2011-03-15

Boilover of tanks is a rare cause of serious fires in crude oil storage. The greatest danger is the spill of burning material from the tank. In the research project presented here, a method to prevent boilover and/or reduce its effects was to be developed. One approach is the addition of additives that modify the hetero-azeotropic boiling characteristics of crude oil components in case of fire. Even minimum concentrations of the additive will delay the time until boilover and also reduce its intensity.

Accumulation Systems of Electric Energy Solved by Multicriteria Analysis Methods IPA and Topsis

Directory of Open Access Journals (Sweden)

Zdenek Hradilek

2008-01-01

Full Text Available This work deals with utilization of multicriteria analysis methods IPA and TOPSIS to assess three storage systems (Fuel Cells, Lead Acid Batteries and Pumped Storage Hydro Plants. Procedures of IPA and TOPSIS methods are described here as like as calculation of mentioned problem. Storage systems are assessed in terms of four criteria (Start up Time, Efficiency of Accumulation, Lifetime and Specific Costs/ kW of Power Output. Weights of criteria are also focused here. They are suggested by experts and statistically calculated.

A Method for Fabricating Additive Manufactured Lightweight Metallic Mirrors

Science.gov (United States)

2015-06-14

machinable by diamond turning. It  has added optical advantages such as  temperature  stability,  high  reflectivity, and resistance to  corrosion.  The...manufacturing  cost and lead times are serious limitations. The cost is very  high  because of both the rarity of  beryllium and the  high  toxicity of...beryllium mirrors beyond the typical  isogrid design. One of those methods explores the bonding or  brazing  of aluminum face sheets  to aluminum foams

Usage of ATND method to determination of mechanical properties of AlMg10 alloy with complex additive of SbNiCr

Directory of Open Access Journals (Sweden)

J. Pezda

2009-07-01

Full Text Available Aluminum alloys with magnesium are commonly used in foundry industry due to lower density and higher corrosion resistance, comparing with silumins. Complicated shapes of produced alloys, differences in wall thickness and operation under changing loads require performing quality control as early as in stage of their preparation (melting. To register crystallization processes and monitor a phenomena arisen in result of the crystallization, are implemented methods based on analysis of temperature change (ATD, DTA. In the paper is present an attempt of usage of the ATND method (Thermal-Voltage-Derivative Analysis to registration of crystallization process of the investigated alloy. Obtained results concern registration of the crystallization process, strength and fatigue tests of the material, and visual observation of morphology of alloy’s fracture after static tensile test. Performed regression analysis has enabled implementation of changeable values of characteristic points of the ATND method to estimation of mechanical properties of the AlMg10 alloy with SbNiCr additive.

A habitat suitability model for Chinese sturgeon determined using the generalized additive method

Science.gov (United States)

Yi, Yujun; Sun, Jie; Zhang, Shanghong

2016-03-01

The Chinese sturgeon is a type of large anadromous fish that migrates between the ocean and rivers. Because of the construction of dams, this sturgeon's migration path has been cut off, and this species currently is on the verge of extinction. Simulating suitable environmental conditions for spawning followed by repairing or rebuilding its spawning grounds are effective ways to protect this species. Various habitat suitability models based on expert knowledge have been used to evaluate the suitability of spawning habitat. In this study, a two-dimensional hydraulic simulation is used to inform a habitat suitability model based on the generalized additive method (GAM). The GAM is based on real data. The values of water depth and velocity are calculated first via the hydrodynamic model and later applied in the GAM. The final habitat suitability model is validated using the catch per unit effort (CPUEd) data of 1999 and 2003. The model results show that a velocity of 1.06-1.56 m/s and a depth of 13.33-20.33 m are highly suitable ranges for the Chinese sturgeon to spawn. The hydraulic habitat suitability indexes (HHSI) for seven discharges (4000; 9000; 12,000; 16,000; 20,000; 30,000; and 40,000 m3/s) are calculated to evaluate integrated habitat suitability. The results show that the integrated habitat suitability reaches its highest value at a discharge of 16,000 m3/s. This study is the first to apply a GAM to evaluate the suitability of spawning grounds for the Chinese sturgeon. The study provides a reference for the identification of potential spawning grounds in the entire basin.

Additive manufacturing of metals

International Nuclear Information System (INIS)

Herzog, Dirk; Seyda, Vanessa; Wycisk, Eric; Emmelmann, Claus

2016-01-01

Additive Manufacturing (AM), the layer-by layer build-up of parts, has lately become an option for serial production. Today, several metallic materials including the important engineering materials steel, aluminium and titanium may be processed to full dense parts with outstanding properties. In this context, the present overview article describes the complex relationship between AM processes, microstructure and resulting properties for metals. It explains the fundamentals of Laser Beam Melting, Electron Beam Melting and Laser Metal Deposition, and introduces the commercially available materials for the different processes. Thereafter, typical microstructures for additively manufactured steel, aluminium and titanium are presented. Special attention is paid to AM specific grain structures, resulting from the complex thermal cycle and high cooling rates. The properties evolving as a consequence of the microstructure are elaborated under static and dynamic loading. According to these properties, typical applications are presented for the materials and methods for conclusion.

Uncertainty Analyses for Back Projection Methods

Science.gov (United States)

Zeng, H.; Wei, S.; Wu, W.

2017-12-01

So far few comprehensive error analyses for back projection methods have been conducted, although it is evident that high frequency seismic waves can be easily affected by earthquake depth, focal mechanisms and the Earth's 3D structures. Here we perform 1D and 3D synthetic tests for two back projection methods, MUltiple SIgnal Classification (MUSIC) (Meng et al., 2011) and Compressive Sensing (CS) (Yao et al., 2011). We generate synthetics for both point sources and finite rupture sources with different depths, focal mechanisms, as well as 1D and 3D structures in the source region. The 3D synthetics are generated through a hybrid scheme of Direct Solution Method and Spectral Element Method. Then we back project the synthetic data using MUSIC and CS. The synthetic tests show that the depth phases can be back projected as artificial sources both in space and time. For instance, for a source depth of 10km, back projection gives a strong signal 8km away from the true source. Such bias increases with depth, e.g., the error of horizontal location could be larger than 20km for a depth of 40km. If the array is located around the nodal direction of direct P-waves the teleseismic P-waves are dominated by the depth phases. Therefore, back projections are actually imaging the reflection points of depth phases more than the rupture front. Besides depth phases, the strong and long lasted coda waves due to 3D effects near trench can lead to additional complexities tested here. The strength contrast of different frequency contents in the rupture models also produces some variations to the back projection results. In the synthetic tests, MUSIC and CS derive consistent results. While MUSIC is more computationally efficient, CS works better for sparse arrays. In summary, our analyses indicate that the impact of various factors mentioned above should be taken into consideration when interpreting back projection images, before we can use them to infer the earthquake rupture physics.

Calculation methods' comparative analysis of monorail hoist crane local bending effects

Directory of Open Access Journals (Sweden)

Cvijović Goran M.

2016-01-01

Full Text Available The results of numerical and experimental researches of local bending problems, carried on classic and medium-wide I profiles, were a basis for the adoption of the current standards (EN 15011: 2014 which regulates the action of the local stress caused by the effect of cart wheels. Regarding the fact that IPB (HE-B wide flange profiles are largely used for production of the main carriers of monorail transport systems, this paper presents the results of the action of the local stress caused by the effect of cart wheels on the HE-A flange profile, using the methods and procedures of relevant researchers, the procedures prescribed by the standard EN 15011 as well as the results of calculations using finite element method. It has been revealed, based on comparative analysis of the results, that in the transition zone low flange / rib longitudinal local stress on the lower contour flange, determined using the above mentioned standards have tightening characteristic, while all other methods, including finite element method, give the pressing nature of the considered voltage. In addition, all of these procedures, except for the finite element method, adopt the assumption that absolute value of voltage, caused by local bending on upper and lower contour of the loaded flange, are the same, and there is no physical justification. Bearing in mind the fact that stress identification, caused by the flange local bending, is an extremely important phase proving the strength of monorail beams, we may conclude that the application of standard EN 15011 does not provide reliable results when it comes to wide flange profiles.

Technological foundations of processing tomato pomace in feed additives

Directory of Open Access Journals (Sweden)

B. Yegorov

2015-05-01

Full Text Available Introduction. Search for new types of alternative raw material for the efficient development of poultry industry and problem of waste disposal of canning industry made it necessary to develop a method of processing tomato pomace in feed additives. Materials and methods. Sampling, preparation and testing were carried out by general and specific organ oleptic and physical-technological methods of assessment and analysis of the properties of raw materials and finished products. Results. Incorporation of tomato pomace in the feed additive reduces the cost of raw materials and expenses associated with moistening of the mixture before extrusion and incorporation of chalk feed will solve the problem of calcium imbalance of laying hens. It was found that extrusion process has improved the physical properties of feed additive and showed the possibility of its use as a feed component: moisture content decreased by 34.5 %, the angle of repose increased by 11.4 %, flowability decreased by 39.7 % and bulk density decreased by 32.3 %. Conclusions. The resulting feed additive will solve the problem of diversification of raw materials, waste, calcium imbalance of laying hens and reduce expenses on compound animal feedstuff production.

Degradation of Paraquat in Gramoxone Pesticide with Addition of ZnO

Directory of Open Access Journals (Sweden)

Febrina Arfi

2017-11-01

Full Text Available Paraquat is the most toxic herbicide, the main agricultural crops and plantations that use them are cloves, cocoa, oil palm, rubber, coffee, and pepper. Therefore, it is necessary to study to degrade paraquat compounds by photolysis method with using ZnO. Photolysis is a process of UV irradiation with a wavelength of 200-400 nm. In this study Photolysis method used UV light with λ = 365 nm. Degradation of paraquat compound was done with the influence of variation of time without the addition ZnO, the influence of ZnO additional variations, and the effect of combination between variations of time and optimization of ZnO addition. The result of the study shows that photolysis degradation product without the addition of ZnO for 120 minutes has been degraded by 12.56%. While the optimum addition of 0.1 grams ZnO increased the percentage of degradation which is about 57.64%. This is proved that the addition of ZnO with photolysis method can degrade more paraquat compounds.

Solving point reactor kinetic equations by time step-size adaptable numerical methods

International Nuclear Information System (INIS)

Liao Chaqing

2007-01-01

Based on the analysis of effects of time step-size on numerical solutions, this paper showed the necessity of step-size adaptation. Based on the relationship between error and step-size, two-step adaptation methods for solving initial value problems (IVPs) were introduced. They are Two-Step Method and Embedded Runge-Kutta Method. PRKEs were solved by implicit Euler method with step-sizes optimized by using Two-Step Method. It was observed that the control error has important influence on the step-size and the accuracy of solutions. With suitable control errors, the solutions of PRKEs computed by the above mentioned method are accurate reasonably. The accuracy and usage of MATLAB built-in ODE solvers ode23 and ode45, both of which adopt Runge-Kutta-Fehlberg method, were also studied and discussed. (authors)

Field and laboratory determination of a poly(vinyl/vinylidene chloride) additive in brick mortar.

Science.gov (United States)

Law, S L; Newman, J H; Ptak, F L

1990-02-01

A polymerized vinyl/vinylidene chloride additive, used in brick mortar during the 60s and 70s, is detected at the building site by the field method, which employs a commercially available chloride test strip. The field test results can then be verified by the laboratory methods. In one method, total chlorine in the mortar is determined by an oxygen-bomb method and the additive chloride is determined by difference after water-soluble chlorides have been determined on a separate sample. In the second method, the polymerized additive is extracted directly from the mortar with tetrahydrofuran (THF). The difference in weight before and after extraction of the additive gives the weight of additive in the mortar. Evaporation of the THF from the extract leaves a thin film of the polymer, which gives an infrared "fingerprint" spectrum characteristic of the additive polymer.

Silver recovery from the waste materials by the method of flotation process

OpenAIRE

B. Oleksiak; G. Siwiec; A. Tomaszewska; D. Piękoś

2018-01-01

During the leaching process of zinc concentrates, the waste materials rich in various metals such as eg. silver are produced. So far no attempts of silver recovery from the mentioned waste materials have been made due to the lack of any method which would be both effective and beneficial. The paper presents some possibilities of application of flotation process in silver recovery form waste materials generated during zinc production.

Method of pyrolytic decomposition and coking of a mixture of finely distributed solid or semisolid carbonaceous material and hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

1933-09-09

A method of pyrolytic decomposition and coking of a mixture of finely distributed of solid or semi-solid carbonaceous material and hydrocarbon oils is disclosed whereby the mixture is exposed to a decomposition temperature and later is brought into the zone of decomposition where vapors are separated from the unvaporized residue and the vapors are exposed to fractional condensation for the purpose of obtaining a light product of distillation. The method is characterized by the mixture being exposed to heating by means of indirect exchange of heat in a heating zone or by means of a direct addition of a hot heat-conducting medium, or by means of both the mentioned indirect exchange of heat and direct heat under such conditions that the unvaporized residue obtained from the thus-heated mixture in the decomposition zone is transformed to solid coke in this zone by being heated to coking temperature in a comparatively thin layer on the surface of the decomposition zone that has been heated to a high temperature.

The Monte Carlo method as a tool for statistical characterisation of differential and additive phase shifting algorithms

International Nuclear Information System (INIS)

Miranda, M; Dorrio, B V; Blanco, J; Diz-Bugarin, J; Ribas, F

2011-01-01

Several metrological applications base their measurement principle in the phase sum or difference between two patterns, one original s(r,φ) and another modified t(r,φ+Δφ). Additive or differential phase shifting algorithms directly recover the sum 2φ+Δφ or the difference Δφ of phases without requiring prior calculation of the individual phases. These algorithms can be constructed, for example, from a suitable combination of known phase shifting algorithms. Little has been written on the design, analysis and error compensation of these new two-stage algorithms. Previously we have used computer simulation to study, in a linear approach or with a filter process in reciprocal space, the response of several families of them to the main error sources. In this work we present an error analysis that uses Monte Carlo simulation to achieve results in good agreement with those obtained with spatial and temporal methods.

A mathematical approach to optimal selection of dose values in the additive dose method of ERP dosimetry

International Nuclear Information System (INIS)

Hayes, R.B.; Haskell, E.H.; Kenner, G.H.

1996-01-01

Additive dose methods commonly used in electron paramagnetic resonance (EPR) dosimetry are time consuming and labor intensive. We have developed a mathematical approach for determining optimal spacing of applied doses and the number of spectra which should be taken at each dose level. Expected uncertainitites in the data points are assumed to be normally distributed with a fixed standard deviation and linearity of dose response is also assumed. The optimum spacing and number of points necessary for the minimal error can be estimated, as can the likely error in the resulting estimate. When low doses are being estimated for tooth enamel samples the optimal spacing is shown to be a concentration of points near the zero dose value with fewer spectra taken at a single high dose value within the range of known linearity. Optimization of the analytical process results in increased accuracy and sample throughput

Correlation Coefficients Between Different Methods of Expressing Bacterial Quantification Using Real Time PCR

Directory of Open Access Journals (Sweden)

Bahman Navidshad

2012-02-01

Full Text Available The applications of conventional culture-dependent assays to quantify bacteria populations are limited by their dependence on the inconsistent success of the different culture-steps involved. In addition, some bacteria can be pathogenic or a source of endotoxins and pose a health risk to the researchers. Bacterial quantification based on the real-time PCR method can overcome the above-mentioned problems. However, the quantification of bacteria using this approach is commonly expressed as absolute quantities even though the composition of samples (like those of digesta can vary widely; thus, the final results may be affected if the samples are not properly homogenized, especially when multiple samples are to be pooled together before DNA extraction. The objective of this study was to determine the correlation coefficients between four different methods of expressing the output data of real-time PCR-based bacterial quantification. The four methods were: (i the common absolute method expressed as the cell number of specific bacteria per gram of digesta; (ii the Livak and Schmittgen, ΔΔCt method; (iii the Pfaffl equation; and (iv a simple relative method based on the ratio of cell number of specific bacteria to the total bacterial cells. Because of the effect on total bacteria population in the results obtained using ΔCt-based methods (ΔΔCt and Pfaffl, these methods lack the acceptable consistency to be used as valid and reliable methods in real-time PCR-based bacterial quantification studies. On the other hand, because of the variable compositions of digesta samples, a simple ratio of cell number of specific bacteria to the corresponding total bacterial cells of the same sample can be a more accurate method to quantify the population.

The Nodal Polynomial Expansion method to solve the multigroup diffusion equations

International Nuclear Information System (INIS)

Ribeiro, R.D.M.

1983-03-01

The methodology of the solutions of the multigroup diffusion equations and uses the Nodal Polynomial Expansion Method is covered. The EPON code was developed based upon the above mentioned method for stationary state, rectangular geometry, one-dimensional or two-dimensional and for one or two energy groups. Then, one can study some effects such as the influence of the baffle on the thermal flux by calculating the flux and power distribution in nuclear reactors. Furthermore, a comparative study with other programs which use Finite Difference (CITATION and PDQ5) and Finite Element (CHD and FEMB) Methods was undertaken. As a result, the coherence, feasibility, speed and accuracy of the methodology used were demonstrated. (Author) [pt

Improving protein function prediction methods with integrated literature data

Directory of Open Access Journals (Sweden)

Gabow Aaron P

2008-04-01

Full Text Available Abstract Background Determining the function of uncharacterized proteins is a major challenge in the post-genomic era due to the problem's complexity and scale. Identifying a protein's function contributes to an understanding of its role in the involved pathways, its suitability as a drug target, and its potential for protein modifications. Several graph-theoretic approaches predict unidentified functions of proteins by using the functional annotations of better-characterized proteins in protein-protein interaction networks. We systematically consider the use of literature co-occurrence data, introduce a new method for quantifying the reliability of co-occurrence and test how performance differs across species. We also quantify changes in performance as the prediction algorithms annotate with increased specificity. Results We find that including information on the co-occurrence of proteins within an abstract greatly boosts performance in the Functional Flow graph-theoretic function prediction algorithm in yeast, fly and worm. This increase in performance is not simply due to the presence of additional edges since supplementing protein-protein interactions with co-occurrence data outperforms supplementing with a comparably-sized genetic interaction dataset. Through the combination of protein-protein interactions and co-occurrence data, the neighborhood around unknown proteins is quickly connected to well-characterized nodes which global prediction algorithms can exploit. Our method for quantifying co-occurrence reliability shows superior performance to the other methods, particularly at threshold values around 10% which yield the best trade off between coverage and accuracy. In contrast, the traditional way of asserting co-occurrence when at least one abstract mentions both proteins proves to be the worst method for generating co-occurrence data, introducing too many false positives. Annotating the functions with greater specificity is harder

Addition of HO-nucleophiles to free and coordinated nitriles

International Nuclear Information System (INIS)

Bokach, Nadejda A; Kukushkin, Vadim Yu

2005-01-01

The review surveys data on the addition of HO-nucleophiles (water, oximes, hydroxylamines, hydroxamic acids, alcohols) to nitriles. Main methods for C≡N bond activation in nucleophilic addition reactions are discussed. Particular attention is given to activation of nitriles through coordination to metal centres.

Study of Agronomical and Ecological Parameters of Additive and Replacement Intercropping Systems of Corn (Zea maize L. and Soybean (Glycine max L. Merr.

Directory of Open Access Journals (Sweden)

Issa Piri

2017-12-01

Full Text Available Introduction Intercropping is a multiple cropping agricultural practice involves growing two or more crops in close proximity. Intercropping of compatible plants also encourages biodiversity, by providing a habitat for a variety of insects and soil organisms that would not be present in a monocrop environment. This in turn can help limit outbreaks of crop pests by increasing predator biodiversity. Additionally, reducing the homogeneity of crops increases the barriers against biological dispersal of pests through the crops. Cereal–legume intercropping plays an important role in subsistence food production in developing countries, especially in the situations of limited resources. Nitrogen fixing legumes can be included to a greater extent in arable cropping systems via intercrops. Legumes contribute to maintaining the soil fertility via nitrogen fixation, which is increased in intercrops due to the more competitive character of the cereal for soil inorganic N. Ariel et al., (2013 showed that,Legume-Cereal Intercropping of corn and soybean may be advantageous compared to monocultures. Corn and soybean intercropping produce high yields of green matter and seed concentrates especially when the corn-soybean ratio is 1:2. Due to the importance of cereal–legume intercropping in the sustainability of agricultural systems, the objective of this study was to determine the effects of cereal-legume intercropping on the total biomass and grain yield and to find the best pattern of additive and replacement intercropping systems in Iranshahr Region. Material and Methods In order to study the agronomical and ecological parameters of additive and replacement intercropping systems of corn and soybean, a field experiment was conducted in 2012-13 in the south of Iranshahr city on a randomized complete block design with three replications. Treatments consisted of 8 different intercropping ratios: corn monoculture (C100S0 and soybean monoculture (C0S100 as sole

On a novel matrix method for three-dimensional photoelasticity

International Nuclear Information System (INIS)

Theocaris, P.S.; Gdoutos, E.E.

1978-01-01

A non-destructive method for the photoelastic determination of three-dimensional stress distributions, based on the Mueller and Jones calculi, is developed. The differential equations satisfied by the Stokes and Jones vectors, when a polarized light beam passes through a photoelastic model, presenting rotation of the secondary principal stress directions, are established in matrix form. The Peano-Baker method is used for the solution of these differential equations in a matrix series form, establishing the elements of the Mueller and Jones matrices of the photoelastic model. These matrices are experimentally determined by using different wavelengths in conjunction with Jones' 'equivalence theorem'. The Neumann equations are immediately deduced from the above-mentioned differential equations. (orig.) [de

Influence of discretization method on the digital control system performance

Directory of Open Access Journals (Sweden)

Futás József

2003-12-01

Full Text Available The design of control system can be divided into two steps. First the process or plant have to be convert into mathematical model form, so that its behavior can be analyzed. Then an appropriate controller have to be design in order to get the desired response of the controlled system. In the continuous time domain the system is represented by differential equations. Replacing a continuous system into discrete time form is always an approximation of the continuous system. The different discretization methods give different digital controller performance. The methods presented on the paper are Step Invariant or Zero Order Hold (ZOH Method, Matched Pole-Zero Method, Backward difference Method and Bilinear transformation. The above mentioned discretization methods are used in developing PI position controller of a dc motor. The motor model was converted by the ZOH method. The performances of the different methods are compared and the results are presented.

Characterization of Metal Powders Used for Additive Manufacturing.

Science.gov (United States)

Slotwinski, J A; Garboczi, E J; Stutzman, P E; Ferraris, C F; Watson, S S; Peltz, M A

2014-01-01

Additive manufacturing (AM) techniques can produce complex, high-value metal parts, with potential applications as critical parts, such as those found in aerospace components. The production of AM parts with consistent and predictable properties requires input materials (e.g., metal powders) with known and repeatable characteristics, which in turn requires standardized measurement methods for powder properties. First, based on our previous work, we assess the applicability of current standardized methods for powder characterization for metal AM powders. Then we present the results of systematic studies carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to structure and chemistry, including X-ray diffraction, energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, and X-Ray photoelectron spectroscopy were also employed. The results of these analyses show how virgin powder changes after being exposed to and recycled from one or more Direct Metal Laser Sintering (DMLS) additive manufacturing build cycles. In addition, these findings can give insight into the actual additive manufacturing process.

Characterization of Metal Powders Used for Additive Manufacturing

Science.gov (United States)

Slotwinski, JA; Garboczi, EJ; Stutzman, PE; Ferraris, CF; Watson, SS; Peltz, MA

2014-01-01

Additive manufacturing (AM) techniques1 can produce complex, high-value metal parts, with potential applications as critical parts, such as those found in aerospace components. The production of AM parts with consistent and predictable properties requires input materials (e.g., metal powders) with known and repeatable characteristics, which in turn requires standardized measurement methods for powder properties. First, based on our previous work, we assess the applicability of current standardized methods for powder characterization for metal AM powders. Then we present the results of systematic studies carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to structure and chemistry, including X-ray diffraction, energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, and X-Ray photoelectron spectroscopy were also employed. The results of these analyses show how virgin powder changes after being exposed to and recycled from one or more Direct Metal Laser Sintering (DMLS) additive manufacturing build cycles. In addition, these findings can give insight into the actual additive manufacturing process. PMID:26601040

Assessment of the further improved (G'/G)-expansion method and the extended tanh-method in probing exact solutions of nonlinear PDEs.

Science.gov (United States)

Akbar, M Ali; Ali, Norhashidah Hj Mohd; Mohyud-Din, Syed Tauseef

2013-01-01

The (G'/G)-expansion method is one of the most direct and effective method for obtaining exact solutions of nonlinear partial differential equations (PDEs). In the present article, we construct the exact traveling wave solutions of nonlinear evolution equations in mathematical physics via the (2 + 1)-dimensional breaking soliton equation by using two methods: namely, a further improved (G'/G)-expansion method, where G(ξ) satisfies the auxiliary ordinary differential equation (ODE) [G'(ξ)](2) = p G (2)(ξ) + q G (4)(ξ) + r G (6)(ξ); p, q and r are constants and the well known extended tanh-function method. We demonstrate, nevertheless some of the exact solutions bring out by these two methods are analogous, but they are not one and the same. It is worth mentioning that the first method has not been exercised anybody previously which gives further exact solutions than the second one. PACS numbers 02.30.Jr, 05.45.Yv, 02.30.Ik.

Topology Optimization for Reducing Additive Manufacturing Processing Distortions

Science.gov (United States)

2017-12-01

distribution is unlimited. 1. Introduction Additive manufacturing (AM) is a production method that involves gradual, layer- by-layer building of material... design space—allowing the production of pre- viously unmanufacturable topologically optimized structures—constraints remain. One constraint, for...ARL-TR-8242•DEC 2017 US Army Research Laboratory Topology Optimization for ReducingAdditive Manufacturing ProcessingDistortions by Raymond A Wildman

From Vitruvius' ceramic powder additives to modern restoration

Directory of Open Access Journals (Sweden)

Mário Mendonça de Oliveira

2008-01-01

Full Text Available The text aims at giving a general view of the use of lime mortars additivated with ceramic powder taking advantage of its pozzolanic reactions. It emphasizes the main explicit references of this technique in the ancient writers, starting from Vitruvius and going through important theoreticians of the Renaissance, until it reaches the military engineers of the XVII e XVIII centuries, particularly the Portuguese engineers who had a strong influence in the overseas constructions techniques. Some mistakes in the interpretation of these texts regarding the properties attributed to the addition of ceramic powder in lime mortars are also mentioned. The continuation of the work refers to the description and commentaries of the tests and laboratory observations carried out on the additivated mortars in question. Among these are highlighted the hardening time, the mechanical resistance (axial compression and traction by diametral compression, water absorption by capillary uptake, total water porosity, accelerated aging in saturated solution of Na2SO4, loss on ignition x-rays fluorescence, permeability to water vapor and other procedures that contribute to the evaluation of the behavior of lime mortars additivated with the "cocciopesto" and of the pozzolanic reactions occurring in the material. As the theory would have no sense if it is not necessarily put in practice, the work ends with the description of the application of the mortar additivated with ceramic powder in a concrete case of restoration, with the description of the obtained results.

Development of an analytical method for polycyclic aromatic hydrocarbons in coffee beverages and dark beer using novel high-sensitivity technique of supercritical fluid chromatography/mass spectrometry.

Science.gov (United States)

Yoshioka, Toshiaki; Nagatomi, Yasushi; Harayama, Koichi; Bamba, Takeshi

2018-07-01

Polycyclic aromatic hydrocarbons (PAHs) are carcinogenic substances that are mainly generated during heating in food; therefore, the European Union (EU) has regulated the amount of benzo[a]pyrene and PAH4 in various types of food. In addition, the Scientific Committee on Food of the EU and the Joint Food and Agriculture Organization/World Health Organization Expert Committee on Food Additives have recommended that 16 PAHs should be monitored. Since coffee beverages and dark beer are roasted during manufacture, monitoring these 16 PAHs is of great importance. On the other hand, supercritical fluid chromatography (SFC) is a separation method that has garnered attention in recent years as a complement for liquid and gas chromatography. Therefore, we developed a rapid high-sensitivity analytical method for the above-mentioned 16 PAHs in coffee beverages and dark beer involving supercritical fluid chromatography/atmospheric pressure chemical ionization-mass spectrometry (SFC/APCI-MS) and simple sample preparation. In this study, we developed a novel analytical technique that increased the sensitivity of MS detection by varying the back-pressure in SFC depending on the elution of PAHs. In addition, analysis of commercially available coffee and dark beer samples in Japan showed that the risk of containing the 16 PAHs may be low. Copyright © 2018 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Estimation of adjusted rate differences using additive negative binomial regression.

Science.gov (United States)

Donoghoe, Mark W; Marschner, Ian C

2016-08-15

Rate differences are an important effect measure in biostatistics and provide an alternative perspective to rate ratios. When the data are event counts observed during an exposure period, adjusted rate differences may be estimated using an identity-link Poisson generalised linear model, also known as additive Poisson regression. A problem with this approach is that the assumption of equality of mean and variance rarely holds in real data, which often show overdispersion. An additive negative binomial model is the natural alternative to account for this; however, standard model-fitting methods are often unable to cope with the constrained parameter space arising from the non-negativity restrictions of the additive model. In this paper, we propose a novel solution to this problem using a variant of the expectation-conditional maximisation-either algorithm. Our method provides a reliable way to fit an additive negative binomial regression model and also permits flexible generalisations using semi-parametric regression functions. We illustrate the method using a placebo-controlled clinical trial of fenofibrate treatment in patients with type II diabetes, where the outcome is the number of laser therapy courses administered to treat diabetic retinopathy. An R package is available that implements the proposed method. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Separation of Stochastic and Deterministic Information from Seismological Time Series with Nonlinear Dynamics and Maximum Entropy Methods

International Nuclear Information System (INIS)

Gutierrez, Rafael M.; Useche, Gina M.; Buitrago, Elias

2007-01-01

We present a procedure developed to detect stochastic and deterministic information contained in empirical time series, useful to characterize and make models of different aspects of complex phenomena represented by such data. This procedure is applied to a seismological time series to obtain new information to study and understand geological phenomena. We use concepts and methods from nonlinear dynamics and maximum entropy. The mentioned method allows an optimal analysis of the available information

Modifications to the Patient Rule-Induction Method that utilize non-additive combinations of genetic and environmental effects to define partitions that predict ischemic heart disease

DEFF Research Database (Denmark)

Dyson, Greg; Frikke-Schmidt, Ruth; Nordestgaard, Børge G

2009-01-01

This article extends the Patient Rule-Induction Method (PRIM) for modeling cumulative incidence of disease developed by Dyson et al. (Genet Epidemiol 31:515-527) to include the simultaneous consideration of non-additive combinations of predictor variables, a significance test of each combination,...

Noncommutative nature of the addition of noncollinear velocities in special relativity and the geometric phase method (commemorating the publication centennial of A Sommerfeld's work)

International Nuclear Information System (INIS)

Malykin, Grigorii B

2010-01-01

In 1909, Arnold Sommerfeld used geometric calculations to show that the relativistic addition of two noncollinear velocities on an imaginary-radius sphere is a noncommutative operation. Sommerfeld was the first to use the geometric phase method to calculate the angle between the resulting velocities depending on the order in which they are added. For this, he related the value of this angle to the excess of the spherical triangle formed by the two original velocities and their sum. In 1931, Sommerfeld applied his method to analyze the Thomas precession. (from the history of physics)

Neutron flux measurement with 6Li and 7Li dual glass scintillators by γ compensation method

International Nuclear Information System (INIS)

Ji Changsong; Zhang Shulan; Zhang Shuheng

1996-01-01

Based on the characteristics of 6 Li glass scintillator which is sensitive to both neutron and gamma rays, and 7 Li glass scintillator which is sensitive to gamma rays only, a new method of detecting weak neutron flux under interference of strong gamma radiation has been investigated by means of 6 Li- 7 Li pair glass scintillator gamma compensation method. The result of neutron flux measurement by above-mentioned method with an error of about 1% when the gamma ray interference is up to 18.7% has been obtained

Neutron flux measurement with 6Li and 7Li dual glass scintillators by γ compensation method

International Nuclear Information System (INIS)

Ji Changsong; Zhang Shulan; Zhang Shuheng

1998-01-01

Based on the characteristics of 6 Li glass scintillator which is sensitive to both neutron and gamma rays, and 7 Li glass scintillator which is sensitive to gamma rays only, a new method of detecting weak neutron flux under interference of strong gamma radiation has been investigated by mans of 6 Li- 7 Li dual glass scintillator gamma compensation method. The result of neutron flux measurement by above-mentioned method with an error of about 1% when the gamma ray interference is up to 18.7% has been obtained

Grain Structure Control of Additively Manufactured Metallic Materials

Directory of Open Access Journals (Sweden)

Fuyao Yan

2017-11-01

Full Text Available Grain structure control is challenging for metal additive manufacturing (AM. Grain structure optimization requires the control of grain morphology with grain size refinement, which can improve the mechanical properties of additive manufactured components. This work summarizes methods to promote fine equiaxed grains in both the additive manufacturing process and subsequent heat treatment. Influences of temperature gradient, solidification velocity and alloy composition on grain morphology are discussed. Equiaxed solidification is greatly promoted by introducing a high density of heterogeneous nucleation sites via powder rate control in the direct energy deposition (DED technique or powder surface treatment for powder-bed techniques. Grain growth/coarsening during post-processing heat treatment can be restricted by presence of nano-scale oxide particles formed in-situ during AM. Grain refinement of martensitic steels can also be achieved by cyclic austenitizing in post-processing heat treatment. Evidently, new alloy powder design is another sustainable method enhancing the capability of AM for high-performance components with desirable microstructures.

The work of the European Union Reference Laboratory for Food Additives (EURL) and its support for the authorisation process of feed additives in the European Union: a review

Science.gov (United States)

von Holst, Christoph; Robouch, Piotr; Bellorini, Stefano; de la Huebra, María José González; Ezerskis, Zigmas

2016-01-01

ABSTRACT This paper describes the operation of the European Union Reference Laboratory for Feed Additives (EURL) and its role in the authorisation procedure of feed additives in the European Union. Feed additives are authorised according to Regulation (EC) No. 1831/2003, which introduced a completely revised authorisation procedure and also established the EURL. The regulations authorising feed additives contain conditions of use such as legal limits of the feed additives, which require the availability of a suitable method of analysis for official control purposes under real world conditions. It is the task of the EURL to evaluate the suitability of analytical methods as proposed by the industry for this purpose. Moreover, the paper shows that one of the major challenges is the huge variety of the methodology applied in feed additive analysis, thus requiring expertise in quite different analytical areas. In order to cope with this challenge, the EURL is supported by a network of national reference laboratories (NRLs) and only the merged knowledge of all NRLs allows for a scientifically sound assessment of the analytical methods. PMID:26540604

Effect of {gamma}` and {gamma} (Ag{sub 2}Al) precipitates on the steady state creep of Al-16wt%Ag alloys with and without Zr addition

Energy Technology Data Exchange (ETDEWEB)

Deaf, G.H. [Ain Shams Univ., Cairo (Egypt). Dept. of Physics; Youssef, S.B. [Ain Shams Univ., Cairo (Egypt). Dept. of Physics; Mahmoud, M.A. [Ain Shams Univ., Cairo (Egypt). Dept. of Physics

1996-11-16

The steady state creep behaviour of Al-16 wt% Ag and Al-16 wt% Ag-0.1 wt% Zr alloys has been studied at constant load (= 137.2 MPa) and tested at different working temperatures for samples aged at temperatures favouring the formation of {gamma}` and {gamma} precipitates. It was found that addition of Zr to Al-16 wt% Ag alloy accelerates the precipitations {gamma}` and {gamma} due to the formation of the metastable phase Al{sub 3}Zr. For both alloys, two values of activation energy have been obtained as (34 {+-} 0.3) kJ/mol for viscous glide of dislocations due to the existence of {gamma}` precipitates and (68 {+-} 0.3) kJ/mol for grain boundary diffusion due to the existence of {gamma} precipitates. TEM investigations of {gamma}` and {gamma} precipitates confirmed the above-mentioned effect of Zr addition. (orig.)

Silver recovery from the waste materials by the method of flotation process

Directory of Open Access Journals (Sweden)

B. Oleksiak

2018-01-01

Full Text Available During the leaching process of zinc concentrates, the waste materials rich in various metals such as eg. silver are produced. So far no attempts of silver recovery from the mentioned waste materials have been made due to the lack of any method which would be both effective and beneficial. The paper presents some possibilities of application of flotation process in silver recovery form waste materials generated during zinc production.

Assessment of methods for analyzing gaseous mixtures of hydrogen isotopes and helium

International Nuclear Information System (INIS)

Attalla, A.; Bishop, C.T.; Bohl, D.R.; Buxton, T.L.; Sprague, R.E.; Warner, D.K.

1976-01-01

Mass spectrographic methods have served well in the past to analyze gaseous mixtures of the hydrogen isotopes. Alternate methods of analyses are reviewed which offer wider ranges and variety of isotopic determinations. This report describes possible improvements of the mass spectrographic determinations, gas chromatography, anti-Stokes Raman spectroscopy, microwave-induced optical emission spectroscopy, and methods of measuring tritium using radiation detection devices. Precision, accuracy, limitations, and costs are included for some of the methods mentioned. Costs range from $70,000 for the anti-Stokes Raman spectroscopy equipment, which can determine hydrogen isotopes but not helium, to less than $10,000 for the gas chromatographic equipment, which can determine hydrogen isotopes and helium with precision and accuracy comparable to those of the mass spectrometer

Recommendations for Enhancing Implementation of Additional Protocol Declarations

International Nuclear Information System (INIS)

Niina, Toshiaki; Nidaira, Kazuo; Aono, Yosuke

2010-01-01

Japan signed the Additional Protocol (hereafter, AP) in December 1998. The domestic law and regulation had been revised to implement the initial and annual declarations for the Agency and the Additional Protocol came into force in December 1999. Since initial declaration in 2000, Japan has submitted the annual declaration in every May. Until 2010, Japan has made 10 annual declarations. This paper gives recommendations to enhance implementation of Additional Protocol declarations based on 10-year experience in Japan and addresses the following: Current status of additional protocol declaration in Japan; Outline of processing method; AP Information Management System; Recommendations for improving quality of declaration. Preparation of additional protocol declaration in NMCC has been conducted in the course of contract with Japan Safeguards Office (hereafter, JSGO) for safeguards information treatment. (author)

Bending Moment Decrease of Reinforced Concrete Beam Supported by Additional CFRP

Directory of Open Access Journals (Sweden)

Mykolas Daugevičius

2011-04-01

Full Text Available The calculation method of reinforced concrete beam with additional CFRP composite is proposed in this article. This method estimates tangential angular concrete deformations in tensioned beam layers between steel and bonded carbon fiber reinforced polymer. The horizontal slip of CFRP composite reduce beam bending moment capacity. An additional coefficient to reduce CFRP resultant force is necessary for better precision of bending moment capacity. Also, various calculation methods of bending moment capacity are considered. Article in Lithuanian

Experimental investigation of radiation effect on human thermal comfort by Taguchi method

International Nuclear Information System (INIS)

Arslanoglu, Nurullah; Yigit, Abdulvahap

2016-01-01

Highlights: • Radiation heat flux from lighting lamps on human thermal comfort is studied. • The effect of posture position on thermal comfort is investigated. • The effect of clothing color on thermal comfort is examined. • Radiation heat flux from halogen reflector lamp increase skin temperature more. • Posture position effect on thermal comfort is less than the other parameters. - Abstract: In this study, the effect of radiation heat flux of lighting lamps on human thermal comfort was investigated by using Taguchi method. In addition, at indoor conditions, clothing color and posture position under the radiation effect on thermal comfort were also investigated. For this purpose, experiments were performed in an air conditioned laboratory room in summer and autumn seasons. The amount of temperature rise on the back was considered as performance parameter. An L8 orthogonal array was selected as an experimental plan for the third parameters mentioned above for summer and autumn seasons. The results were analyzed for the optimum conditions using signal-to-noise (S/N) ratio and ANOVA method. The optimum results were found to be clear halogen lamp as lighting lamp, white as t-shirt color, standing as posture position, in summer season. The optimum levels of the lighting lamp, t-shirt color and posture position were found to be clear halogen lamp, white, sitting in autumn season, respectively.

Some non-thermal microbial inactivation methods in dairy products

International Nuclear Information System (INIS)

Yangilar, F.; Kabil, E.

2013-01-01

During the production of dairy products, some thermal processes such as pasteurization and sterilization are used commonly to inactive microorganisms. But as a result of thermal processes, loss of nutrient and aroma, non-enzymatic browning and organoleptic differentiation especially in dairy products are seen. Because of this, alternative methods are needed to provide microbial inactivation and as major problems are caused by high temperatures, non-thermal processes are focused on. For this purpose, some methods such as high pressure (HP), pulsed light (PL), ultraviolet radiation (UV), supercritical carbon dioxide (SC-CO2) or pulsed electric field (PEF) are used in food. These methods products are processed in ambient temperature and so not only mentioned losses are minimized but also freshness and naturality of products can be preserved. In this work, we will try to be given information about methods of non-thermal microbial inactivation of dairy products. (author) [tr

Cleaning Process Development for Metallic Additively Manufactured Parts

Science.gov (United States)

Tramel, Terri L.; Welker, Roger; Lowery, Niki; Mitchell, Mark

2014-01-01

Additive Manufacturing of metallic components for aerospace applications offers many advantages over traditional manufacturing techniques. As a new technology, many aspects of its widespread utilization remain open to investigation. Among these are the cleaning processes that can be used for post finishing of parts and measurements to verify effectiveness of the cleaning processes. Many cleaning and drying processes and measurement methods that have been used for parts manufactured using conventional techniques are candidates that may be considered for cleaning and verification of additively manufactured parts. Among these are vapor degreasing, ultrasonic immersion and spray cleaning, followed by hot air drying, vacuum baking and solvent displacement drying. Differences in porosity, density, and surface finish of additively manufactured versus conventionally manufactured parts may introduce new considerations in the selection of cleaning and drying processes or the method used to verify their effectiveness. This presentation will review the relative strengths and weaknesses of different candidate cleaning and drying processes as they may apply to additively manufactured metal parts for aerospace applications. An ultrasonic cleaning technique for exploring the cleanability of parts will be presented along with an example using additively manufactured Inconel 718 test specimens to illustrate its use. The data analysis shows that this ultrasonic cleaning approach results in a well-behaved ultrasonic cleaning/extraction behavior. That is, it does not show signs of accelerated cavitation erosion of the base material, which was later confirmed by neutron imaging. In addition, the analysis indicated that complete cleaning would be achieved by ultrasonic immersion cleaning at approximately 5 minutes, which was verified by subsequent cleaning of additional parts.

The Impact of Wine Style and Sugar Addition in liqueur d’expedition (dosage Solutions on Traditional Method Sparkling Wine Composition

Directory of Open Access Journals (Sweden)

Belinda Kemp

2017-01-01

Full Text Available The purpose of this study was to investigate the effect of wine style and cane sugar addition in the liqueur d’expedition (dosage solution on volatile aroma compounds (VOCs in traditional method sparkling wine. There were 24 bottles of each treatment produced. Treatments were sparkling wine zero dosage (ZD; NV sparkling wine + sugar (BS; unoaked still Chardonnay wine + sugar (UC; Pinot noir 2009 sparkling wine + sugar (PN; Niagara produced Brandy + sugar (B and Icewine (IW. The control treatment in the sensory analysis was an oaked still Chardonnay wine + sugar (OC because the zero-dosage wine was not suitable for a difference test that compared wines with sugar to one without. Standard wine chemical parameters were analysed before disgorging and after liqueur d’expedition was added and included; pH, titratable acidity (TA g/L, alcohol (v/v %, residual sugar (RS g/L, free and total SO2 and total phenolics (A.U.. Volatile aroma compounds (VOCs analysed by Headspace Solid- Phase Micro-Extraction Gas Chromatography-Mass Spectrometry (HS-SPME-GC-MS included two alcohols, and six ethyl esters. ZD wines had the highest foam height and highest dissolved oxygen level. Sugar affected VOC concentrations in all treatments at five weeks post-disgorging, but by 15 weeks after liqueur d’expedition addition, the wine with added sugar had similar VOC concentrations to the ZD wines. The type of wines used in the dosage solutions had more influence on VOC concentrations than sugar addition.

A new ultrasonic method to detect chemical additives in branded milk

Indian Academy of Sciences (India)

Abstract. A new ultrasonic method – thermoacoustic analysis – is reported for the detection of the added chemical preservatives in branded milk. The nature of variation and shift in the thermal response of the acoustic parameters specific acoustic impedance, adiabatic compressibility and Rao's specific sound velocity for ...

Estimating additive and non-additive genetic variances and predicting genetic merits using genome-wide dense single nucleotide polymorphism markers.

Directory of Open Access Journals (Sweden)

Guosheng Su

Full Text Available Non-additive genetic variation is usually ignored when genome-wide markers are used to study the genetic architecture and genomic prediction of complex traits in human, wild life, model organisms or farm animals. However, non-additive genetic effects may have an important contribution to total genetic variation of complex traits. This study presented a genomic BLUP model including additive and non-additive genetic effects, in which additive and non-additive genetic relation matrices were constructed from information of genome-wide dense single nucleotide polymorphism (SNP markers. In addition, this study for the first time proposed a method to construct dominance relationship matrix using SNP markers and demonstrated it in detail. The proposed model was implemented to investigate the amounts of additive genetic, dominance and epistatic variations, and assessed the accuracy and unbiasedness of genomic predictions for daily gain in pigs. In the analysis of daily gain, four linear models were used: 1 a simple additive genetic model (MA, 2 a model including both additive and additive by additive epistatic genetic effects (MAE, 3 a model including both additive and dominance genetic effects (MAD, and 4 a full model including all three genetic components (MAED. Estimates of narrow-sense heritability were 0.397, 0.373, 0.379 and 0.357 for models MA, MAE, MAD and MAED, respectively. Estimated dominance variance and additive by additive epistatic variance accounted for 5.6% and 9.5% of the total phenotypic variance, respectively. Based on model MAED, the estimate of broad-sense heritability was 0.506. Reliabilities of genomic predicted breeding values for the animals without performance records were 28.5%, 28.8%, 29.2% and 29.5% for models MA, MAE, MAD and MAED, respectively. In addition, models including non-additive genetic effects improved unbiasedness of genomic predictions.

Analysis of Formal Methods for Specification of E-Commerce Applications

Directory of Open Access Journals (Sweden)

Sadiq Ali Khan

2016-01-01

Full Text Available E-commerce based application characteristics portray elevated dynamics while incorporating decentralized nature. Extreme emphasis influencing structural design plus implementation, positions such applications highly appreciated. Significant research articles reveal that, applying formal methods addressing challenges incumbent with E-commerce based applications, contribute towards reliability and robustness obliging the system. Anticipating and designing sturdy e-process and concurrent implementation, allows application behavior extra strength against errors, frauds and hacking, minimizing program faults during application operations. Programmers find extreme difficulty guaranteeing correct processing under all circumstances, however, not impossible. Concealed flaws and errors, triggered only under unexpected and unanticipated scenarios, pilot subtle mistakes and appalling failures. Code authors utilize various formal methods for reducing these flaws. Mentioning prominent methods would include, ASM (Abstract State Machines, B-Method, z-Language, UML (Unified Modelling Language etc. This paper primarily focuses different formal methods applied while deliberating specification and verification techniques for cost effective.

Influence of cobalt and chromium additions on the precipitation processes in a Cu-4Ti alloys; Influencia de la adicion de cobalto y cromo en el proceso de precipitacion en una aleacion de Cu-4Ti

Energy Technology Data Exchange (ETDEWEB)

Donoso, E.

2010-07-01

The influence of 0.5% atomic cobalt and 1% atomic chromium additions on the precipitation hardening of Cu-4Ti alloy was studied by differential scanning calorimetry (DSC) and microhardness measurements. The analysis of the calorimetric curves, for binary alloy, shows the presence of two overlapping exothermic reactions (stages 1 and 2) attributed to the formation of Cu{sub 4}Ti and Cu{sub 3}Ti particles in the copper matrix, respectively. DSC curves for Cu-4Ti-0.5Co alloy shows three exothermic effects (overlapping stages 3 and 4 and stage 5) associated to the formation of phases Ti{sub 2}Co, TiCo and Cu{sub 4}Ti, respectively. DSC curves for Cu-4Ti1Cr alloy shows three exothermic reactions (stages 6, 7 and 9) and one endothermic peak (stage 8). The exothermic reactions correspond to the formation of phases Cr{sub 2}Ti, Cu{sub 4}Ti and Cu{sub 3}Ti, respectively, and the endothermic reactions are attributed to the Cr{sub 2}Ti dissolution. The activation energies calculated using the modified Kissinger method were lower than the ones corresponding to diffusion of cobalt, chromium, and titanium in copper. Kinetic parameters were obtained by a convolution method based on the Johnson-Mehl-Avrami (JMA) formalism. Microhardness measurements confirmed the formation of the mentioned phases. Also, these measurements confirmed the effect of cobalt and chromium addition on the binary alloy hardness. (Author). 31 refs.

Surface texture measurement for additive manufacturing

International Nuclear Information System (INIS)

Triantaphyllou, Andrew; Tomita, Ben; Milne, Katherine A; Giusca, Claudiu L; Macaulay, Gavin D; Roerig, Felix; Hoebel, Matthias; Leach, Richard K

2015-01-01

The surface texture of additively manufactured metallic surfaces made by powder bed methods is affected by a number of factors, including the powder’s particle size distribution, the effect of the heat source, the thickness of the printed layers, the angle of the surface relative to the horizontal build bed and the effect of any post processing/finishing. The aim of the research reported here is to understand the way these surfaces should be measured in order to characterise them. In published research to date, the surface texture is generally reported as an Ra value, measured across the lay. The appropriateness of this method for such surfaces is investigated here. A preliminary investigation was carried out on two additive manufacturing processes—selective laser melting (SLM) and electron beam melting (EBM)—focusing on the effect of build angle and post processing. The surfaces were measured using both tactile and optical methods and a range of profile and areal parameters were reported. Test coupons were manufactured at four angles relative to the horizontal plane of the powder bed using both SLM and EBM. The effect of lay—caused by the layered nature of the manufacturing process—was investigated, as was the required sample area for optical measurements. The surfaces were also measured before and after grit blasting. (paper)

Surface texture measurement for additive manufacturing

Science.gov (United States)

Triantaphyllou, Andrew; Giusca, Claudiu L.; Macaulay, Gavin D.; Roerig, Felix; Hoebel, Matthias; Leach, Richard K.; Tomita, Ben; Milne, Katherine A.

2015-06-01

The surface texture of additively manufactured metallic surfaces made by powder bed methods is affected by a number of factors, including the powder’s particle size distribution, the effect of the heat source, the thickness of the printed layers, the angle of the surface relative to the horizontal build bed and the effect of any post processing/finishing. The aim of the research reported here is to understand the way these surfaces should be measured in order to characterise them. In published research to date, the surface texture is generally reported as an Ra value, measured across the lay. The appropriateness of this method for such surfaces is investigated here. A preliminary investigation was carried out on two additive manufacturing processes—selective laser melting (SLM) and electron beam melting (EBM)—focusing on the effect of build angle and post processing. The surfaces were measured using both tactile and optical methods and a range of profile and areal parameters were reported. Test coupons were manufactured at four angles relative to the horizontal plane of the powder bed using both SLM and EBM. The effect of lay—caused by the layered nature of the manufacturing process—was investigated, as was the required sample area for optical measurements. The surfaces were also measured before and after grit blasting.

Characterization of the Tribological Behavior of Graphene-Based Additives

Energy Technology Data Exchange (ETDEWEB)

Erck, Robert

2014-09-01

XG-supplied nanocrystalline additives were extensively tested for friction and wear behavior. A technique for investigating the stability of additives was developed, and a report covered filtration and centrifugation methods for settling and filterable content. Friction and wear trends in partially and fully formulated oils were reported. Particle size analysis was performed and reported.

Some elaborating methods of gamma scanning results on irradiated nuclear fuels

International Nuclear Information System (INIS)

Sternini, E.

1979-01-01

Gamma scanning, as a post-irradiation examination, is a technique which provides a large number of informations on irradiated nuclear fuels. Power profile, fission products distribution, average and local burn-up of single elements structural and nuclear behaviour of fuel materials are examples of the obtained informations. In the present work experimental methods and theoretical calculations used at the CNEN hot cell laboratory for the mentioned purposes are described. Errors arising from the application of the gamma scanning technique are also discussed

DMF as an Additive in a Two-Step Spin-Coating Method for 20% Conversion Efficiency in Perovskite Solar Cells.

Science.gov (United States)

Wu, Jionghua; Xu, Xin; Zhao, Yanhong; Shi, Jiangjian; Xu, Yuzhuan; Luo, Yanhong; Li, Dongmei; Wu, Huijue; Meng, Qingbo

2017-08-16

DMF as an additive has been employed in FAI/MAI/IPA (FA= CH 2 (NH 2 ) 2 , MA = CH 3 NH 3 , IPA = isopropanol) solution for a two-step multicycle spin-coating method in order to prepare high-quality FA x MA 1-x PbI 2.55 Br 0.45 perovskite films. Further investigation reveals that the existence of DMF in the FAI/MAI/IPA solution can facilitate perovskite conversion, improve the film morphology, and reduce crystal defects, thus enhancing charge-transfer efficiency. By optimization of the DMF amount and spin-coating cycles, compact, pinhole-free perovskite films are obtained. The nucleation mechanisms of perovskite films in our multicycle spin-coating process are suggested; that is, the introduction of DMF in the spin-coating FAI/MAI/IPA solution can lead to the formation of an amorphous phase PbX 2 -AI-DMSO-DMF (X = I, Br; A = FA, MA) instead of intermediate phase (MA) 2 Pb 3 I 8 ·2DMSO. This amorphous phase, similar to that in the one-step method, can help FAI/MAI penetrate into the PbI 2 framework to completely convert into the perovskite. As high as 20.1% power conversion efficiency (PCE) has been achieved with a steady-state PCE of 19.1%. Our work offers a simple repeatable method to prepare high-quality perovskite films for high-performance PSCs and also help further understand the perovskite-crystallization process.

THE CURRENT METHODS FOR MOLECULAR DIAGNOSTICS OF FISH DISEASES (REVIEW

Directory of Open Access Journals (Sweden)

O. Zaloilo

2016-06-01

Full Text Available Purpose. The methods of molecular diagnostic (MMD gradually become widespread in modern fish farming. MMD contain a wide variety of specific approaches, each of which has distinct limits of their possible applications and is characterized by individual peculiarities in practical performance. In addition to high sensitivity and the possibility of rapid diagnostics, the main advantage of molecular methods is to determine the uncultivated infectious agents. DNA amplification allows identifying pathogenic microorganisms at very small quantities even in the minimum sample volume. Molecular methods of diagnostic enable the determination of infection in latent or acute phases. These methods allow showing the differences between pathogens with similar antigenic structures. The current literature data on this subject usually show a methodology in the narrow context of the tasks or practical results obtained through such approaches. Thus, a synthesis of existing information on the mechanisms of action and the limits of the typical problems of basic methods of molecular diagnostics are an urgent task of fish breeding. In particular, the following description will more effectively choose one or several approaches to identify pathogens in fish. Findings. This paper reviews the basic molecular methods that are used in the world's aquaculture for diagnosis of various diseases in commercial fish species. Originality. This work is a generalization of data on the principles and mechanisms for the implementation of diagnostics based on modern molecular techniques. For each of the mentioned approaches, the most promising areas of application were shown. The information is provided in the form of a comparative analysis of each methodology, indicating positive and negative practical aspects. Practical value. The current review of modern methods of molecular diagnostic in aquaculture is focused on practical application. Generalizing and analytical information can be

Novel and validated titrimetric method for determination of selected angiotensin-II-receptor antagonists in pharmaceutical preparations and its comparison with UV spectrophotometric determination

Directory of Open Access Journals (Sweden)

Shrikant H. Patil

2012-12-01

Full Text Available A novel and simple titrimetric method for determination of commonly used angiotensin-II-receptor antagonists (ARA-IIs is developed and validated. The direct acid base titration of four ARA-IIs, namely eprosartan mesylate, irbesartan, telmisartan and valsartan, was carried out in the mixture of ethanol:water (1:1 as solvent using standardized sodium hydroxide aqueous solution as titrant, either visually using phenolphthalein as an indicator or potentiometrically using combined pH electrode. The method was found to be accurate and precise, having relative standard deviation of less than 2% for all ARA-IIs studied. Also, it was shown that the method could be successfully applied to the assay of commercial pharmaceuticals containing the above-mentioned ARA-IIs. The validity of the method was tested by the recovery studies of standard addition to pharmaceuticals and the results were found to be satisfactory. Results obtained by this method were found to be in good agreement with those obtained by UV spectrophotometric method. For UV spectrophotometric analysis ethanol was used as a solvent and wavelength of 233 nm, 246 nm, 296 nm, and 250 nm was selected for determination of eprosartan mesylate, irbesartan, telmisartan, and valsartan respectively. The proposed titrimetric method is simple, rapid, convenient and sufficiently precise for quality control purposes. Keywords: Angiotensin-II-receptor antagonists, Titrimetric assay, UV spectrophotometry, Validation

Review of Shape Deviation Modeling for Additive Manufacturing

OpenAIRE

Zhu , Zuowei; Keimasi , Safa; ANWER , Nabil; Mathieu , Luc; Qiao , Lihong

2016-01-01

International audience; Additive Manufacturing (AM) is becoming a promising technology capable of building complex customized parts with internal geometries and graded material by stacking up thin individual layers. However, a comprehensive geometric model for Additive Manufacturing is not mature yet. Dimensional and form accuracy and surface finish are still a bottleneck for AM regarding quality control. In this paper, an up-to-date review is drawn on methods and approaches that have been de...

Electrical machining method of insulating ceramics

International Nuclear Information System (INIS)

Fukuzawa, Y.; Mohri, N.; Tani, T.

1999-01-01

This paper describes a new electrical discharge machining method for insulating ceramics using an assisting electrode with either a sinking electrical discharge machine or a wire electrical discharge machine. In this method, the metal sheet or mesh is attached to the ceramic surface as an assisting material for the discharge generation around the insulator surface. When the machining condition changes from the attached material to the workpiece, a cracked carbon layer is formed on the workpiece surface. As this layer has an electrical conductivity, electrical discharge occurs in working oil between the tool electrode and the surface of the workpiece. The carbon is formed from the working oil during this electrical discharge. Even after the material is machined, an electrical discharge occurs in the gap region between the tool electrode and the ceramic because an electrically conductive layer is generated continuously. Insulating ceramics can be machined by the electrical discharge machining method using the above mentioned surface modification phenomenon. In this paper the authors show a machined example demonstrating that the proposed method is available for machining a complex shape on insulating ceramics. Copyright (1999) AD-TECH - International Foundation for the Advancement of Technology Ltd

Development of evaluation method for the quality of NPP MCR operators' communication using work domain analysis (WDA)

International Nuclear Information System (INIS)

Jang, In Seok

2010-02-01

Evolution of work demands has changed industrial evolution to computerization which makes systems complex and complicated: this field is called Complex Socio-Technical Systems. As communication failure is one problem of Complex Socio-Technical Systems, it has been discovered that communication failure is the reason for many incidents and accidents in various industries, including the nuclear, aerospace and railway industries. Despite the fact that there have been many studies on the severity of communication failure, there is no evaluation method for operators' communication quality in NPPs. Therefore, the objectives of this study are to develop an evaluation method for the quality of NPP Main Control Room (MCR) operators' communication and to apply the proposed method to operators in a full-scope simulator. In order to develop the proposed method, the Work Domain Analysis (WDA) method is introduced. Several characteristic of WDA, such as Abstraction Decomposition Space (ADS) and the diagonal of ADS are the key points in developing an evaluation method for the quality of NPP MCR operators' communication. In addition, in order to apply the proposed method, nine teams working in NPPs participated in the field simulation. Evaluation results reveal that operators' communication quality was higher as larger portion of components in the developed evaluation criteria were mentioned. Therefore, the proposed method could be a useful one for evaluating the communication quality in any complex system. In order to verify that the proposed method is meaningful to evaluate communication quality, the evaluation results were further investigated with objective performance measures. Further investigation of the evaluation results also supports the idea that the proposed method can be used in evaluating communication quality

Development on methods for evaluating structure reliability of piping components

International Nuclear Information System (INIS)

Schimpfke, T.; Grebner, H.; Peschke, J.; Sievers, J.

2003-01-01

In the frame of the German reactor safety research program of the Federal Ministry of Economics and Labour, GRS has started to develop an analysis code named PROST (PRObabilistic STructure analysis) for estimating the leak and break probabilities of piping systems in nuclear power plants. The development is based on the experience achieved with applications of the public available US code PRAISE 3.10 (Piping Reliability Analysis Including Seismic Events), which was supplemented by additional features regarding the statistical evaluation and the crack orientation. PROST is designed to be more flexible to changes and supplementations. Up to now it can be used for calculating fatigue problems. The paper mentions the main capabilities and theoretical background of the present PROST development and presents a parametric study on the influence by changing the method of stress intensity factor and limit load calculation and the statistical evaluation options on the leak probability of an exemplary pipe with postulated axial crack distribution. Furthermore the resulting leak probability of an exemplary pipe with postulated circumferential crack distribution is compared with the results of the modified PRAISE computer program. The intention of this investigation is to show trends. Therefore the resulting absolute values for probabilities should not be considered as realistic evaluations. (author)

Colorimetric Method of Loop-Mediated Isothermal Amplification with the Pre-Addition of Calcein for Detecting Flavobacterium columnare and its Assessment in Tilapia Farms.

Science.gov (United States)

Suebsing, Rungkarn; Kampeera, Jantana; Sirithammajak, Sarawut; Withyachumnarnkul, Boonsirm; Turner, Warren; Kiatpathomchai, Wansika

2015-03-01

Flavobacterium columnare, the causative agent of columnaris disease in fish, affects many economically important freshwater fish species. A colorimetric method of loop-mediated isothermal amplification with the pre-addition of calcein (LAMP-calcein) was developed and used to detect the presence of F. columnare in farmed tilapia (Nile Tilapia Oreochromis niloticus and red tilapia [Nile Tilapia × Mozambique Tilapia O. mossambicus]) and rearing water. The detection method, based on a change in color from orange to green, could be performed within 45 min at 63°C. The method was highly specific, as it had no cross-detections with 14 other bacterial species, including other fish pathogens and two Flavobacterium species. The method has a minimum detection limit of 2.2 × 10(2) F. columnare CFU; thus, it is about 10 times more sensitive than conventional PCR. With this method, F. columnare was detected in gonad, gill, and blood samples from apparently healthy tilapia broodstock as well as in samples of fertilized eggs, newly hatched fry, and rearing water. The bacteria isolated from the blood were further characterized biochemically and found to be phenotypically identical to F. columnare. The amplified products from the LAMP-calcein method had 97% homology with the DNA sequence of F. columnare.

Dynamical properties of the growing continuum using multiple-scale method

Directory of Open Access Journals (Sweden)

Hynčík L.

2008-12-01

Full Text Available The theory of growth and remodeling is applied to the 1D continuum. This can be mentioned e.g. as a model of the muscle fibre or piezo-electric stack. Hyperelastic material described by free energy potential suggested by Fung is used whereas the change of stiffness is taken into account. Corresponding equations define the dynamical system with two degrees of freedom. Its stability and the properties of bifurcations are studied using multiple-scale method. There are shown the conditions under which the degenerated Hopf's bifurcation is occuring.

Method for assessment of the technical potential of the plant agricultural waste suitable for energy purposes in Bulgaria

International Nuclear Information System (INIS)

Georgiev, V.

2004-01-01

A method for assessment of technical potential of quantitatively important plant agriculture waste; straw from wheat and barley; corn stalks; sunflower stalks and heads; tobacco stalks; orchard prunings and vineyard prunings suitable for energy purposes for Bulgarian conditions is developed. Data for assessment of the technical potential for 2002 using this method are presented. A comparison between technical potential of mentioned wastes, final energy consumption in agriculture and all branches of Bulgarian economy for 2002 is made. (author)

A conjugate gradient method for solving the non-LTE line radiation transfer problem

Science.gov (United States)

Paletou, F.; Anterrieu, E.

2009-12-01

This study concerns the fast and accurate solution of the line radiation transfer problem, under non-LTE conditions. We propose and evaluate an alternative iterative scheme to the classical ALI-Jacobi method, and to the more recently proposed Gauss-Seidel and successive over-relaxation (GS/SOR) schemes. Our study is indeed based on applying a preconditioned bi-conjugate gradient method (BiCG-P). Standard tests, in 1D plane parallel geometry and in the frame of the two-level atom model with monochromatic scattering are discussed. Rates of convergence between the previously mentioned iterative schemes are compared, as are their respective timing properties. The smoothing capability of the BiCG-P method is also demonstrated.

A manual on using additives

International Nuclear Information System (INIS)

Lee, Bong Hoon

1991-10-01

This book consists of five chapters, which describe plasticizer ; summary, synthesis of plasticizer, basic notion, analysis and test on plasticizer, stabilizer ; stabilizer for plastic, an antioxidant, phosphorous acid estelle, ultraviolet ray absorbent, performance of stabilizer, influence on another additives, mix case of PVC production and analysis method for stabilizer, ultraviolet ray absorbent ; basic property and ultraviolet ray absorbent maker, anti-static agent ; basics, anti-static agent of a high molecule and analysis of anti-static agent, flame retardant of plastic.

Evaluation of the isotopic dilution method with addition of 15 N fertilizer to the soil, for quantification of BNF by legumes

International Nuclear Information System (INIS)

Morales, E.R.B.

1990-01-01

Two pot experiments were carried out in greenhouse, with the objective of evaluating the isotopic dilution method with the addition of 15 N fertilizer to the soil for evaluation of biological nitrogen fixation (BNF) by legumes. Experiment I: with addition of 15 N-fertilizer, according to FRIED and MIDDELBOE (1977), and Experiment II: Without adding the fertilizer, by natural variation of 15 N (δ 15 N). In experiment I, the following crops were utilized as test plants: soybean, bean and cowpea and for the control plants: non nodulating soybean, rice and wheat, with distinct number of plants per pot. The pots containing 8 Kg a Dark red latossol (LE) of Sao Paulo state, Brazil, received the same rate of nitrogen fertilizer with same 15 N enrichment. In experiment II, bean was utilized as test crop and non nodulating soybean and rice as controls, and they did not receive any nitrogen fertilizer. The experiments lasted 81 days, from July to October 1989. The above ground parts of the plants were harvested, for which dry matter weight, total-N and 15 N were determined. (author)

Electrodeposition of Asphaltenes. 2. Effect of Resins and Additives

DEFF Research Database (Denmark)

Khvostichenko, Daria S; Andersen, Simon Ivar

2010-01-01

Electrodeposition of asphaltenes from oil/heptane, asphaltene/heptane, and asphaltene/heptane/additive mixtures has been investigated. Toluene, native petroleum resins, and a synthetic asphaltene dispersant, p-nonylphenol, were used as additives. The addition of these components led to partial...... dissolution of asphaltenes in heptane. The charge of asphaltenic particles was found to be negative in oil/heptane mixtures and positive in asphaltene/heptane mixtures. In asphaltene/heptane/toluene systems, the charge of the deposit varied from positive to neutral to negative, depending upon the method...

Modeling, Simulation, Additive Manufacturing, and Experimental Evaluation of Solid and Porous NiTi

Science.gov (United States)

Taheri Andani, Mohsen

In recent years, shape memory alloys (SMAs) have entered a wide range of engineering applications in fields such as aerospace and medical applications. Nickel-titanium (NiTi) is the most commonly used SMAs due to its excellent functional characteristics (shape memory effect and superelasticity behavior). These properties are based on a solid-solid phase transformation between martensite and austenite. Beside these two characteristics, low stiffness, biocompatibility and corrosion properties of NiTi make it an attractive candidate for biomedical applications (e.g., bone plates, bone screws, and vascular stents). It is well know that manufacturing and processing of NiTi is very challenging. The functional properties of NiTi are significantly affected by the impurity level and due to the high titanium content, NiTi are highly reactive. Therefore, high temperature processed parts through methods such as melting and casting which result in increased impurity levels have inadequate structural and functional properties. Furthermore, high ductility and elasticity of NiTi, adhesion, work hardening and spring back effects make machining quite challenging. These unfavorable effects for machining cause significant tool wear along with decreasing the quality of work piece. Recently, additive manufacturing (AM) has gained significant attention for manufacturing NiTi. Since AM can create a part directly from CAD data, it is predicted that AM can overcome most of the manufacturing difficulties. This technique provides the possibility of fabricating highly complex parts, which cannot be processed by any other methods. Curved holes, designed porosity, and lattice like structures are some examples of mentioned complex parts. This work investigates manufacturing superelastic NiTi by selective laser melting (SLM) technique (using PXM by Phenix/3D Systems). An extended experimental study is conducted on the effect of subsequent heat treatments with different aging conditions on phase

Chemical decontaminating method for stainless steel

International Nuclear Information System (INIS)

Onuma, Tsutomu; Akimoto, Hidetoshi.

1990-01-01

Radioactive metal wastes comprising passivated stainless steels are chemically decontaminated to such a radioactivity level as that of usual wastes. The present invention for chemically decontaminating stainless steels comprises a first step of immersing decontaminates into a sulfuric acid solution and a second step of immersing them into an aqueous solution prepared by adding oxidative metal salts to sulfuric acid, in which a portion of the surface of stainless steels as decontaminates are chemically ground to partially expose substrate materials and then the above-mentioned decontamination steps are applied. More than 90% of radioactive materials are removed in this method by the dissolution of the exposed substrate materials and peeling of cruds secured to the surface of the materials upon dissolution. This method is applicable to decontamination of articles having complicate shapes, can reduce the amount of secondary wastes after decontamination and also remarkably shorten the time required for decontamination. (T.M.)

Development of rupture process analysis method for great earthquakes using Direct Solution Method

Science.gov (United States)

Yoshimoto, M.; Yamanaka, Y.; Takeuchi, N.

2010-12-01

Conventional rupture process analysis methods using teleseismic body waves were based on ray theory. Therefore, these methods have the following problems in applying to great earthquakes such as 2004 Sumatra earthquake: (1) difficulty in computing all later phases such as the PP reflection phase, (2) impossibility of computing called “W phase”, the long period phase arriving before S wave, (3) implausibility of hypothesis that the distance is far enough from the observation points to the hypocenter compared to the fault length. To solve above mentioned problems, we have developed a new method which uses the synthetic seismograms computed by the Direct Solution Method (DSM, e.g. Kawai et al. 2006) as Green’s functions. We used the DSM software (http://www.eri.u-tokyo.ac.jp/takeuchi/software/) for computing the Green’s functions up to 1 Hz for the IASP91 (Kennett and Engdahl, 1991) model, and determined the final slip distributions using the waveform inversion method (Kikuchi et al. 2003). First we confirmed whether the Green’s functions computed by DSM were accurate in higher frequencies up to 1 Hz. Next we performed the rupture process analysis of this new method for Mw8.0 (GCMT) large Solomon Islands earthquake on April 1, 2007. We found that this earthquake consisted of two asperities and the rupture propagated across the subducting Sinbo ridge. The obtained slip distribution better correlates to the aftershock distributions than existing method. Furthermore, this new method keep same accuracy of existing method (which has the advantage of calculating) with respect to direct P-wave and reflection phases near the source, and also accurately calculate the later phases such a PP-wave.

Methods for Measuring and Estimating Methane Emission from Ruminants

Directory of Open Access Journals (Sweden)

Jørgen Madsen

2012-04-01

Full Text Available This paper is a brief introduction to the different methods used to quantify the enteric methane emission from ruminants. A thorough knowledge of the advantages and disadvantages of these methods is very important in order to plan experiments, understand and interpret experimental results, and compare them with other studies. The aim of the paper is to describe the principles, advantages and disadvantages of different methods used to quantify the enteric methane emission from ruminants. The best-known methods: Chambers/respiration chambers, SF6 technique and in vitro gas production technique and the newer CO2 methods are described. Model estimations, which are used to calculate national budget and single cow enteric emission from intake and diet composition, are also discussed. Other methods under development such as the micrometeorological technique, combined feeder and CH4 analyzer and proxy methods are briefly mentioned. Methods of choice for estimating enteric methane emission depend on aim, equipment, knowledge, time and money available, but interpretation of results obtained with a given method can be improved if knowledge about the disadvantages and advantages are used in the planning of experiments.

Evaluating methods for controlling depth perception in stereoscopic cinematography

Science.gov (United States)

Sun, Geng; Holliman, Nick

2009-02-01

Existing stereoscopic imaging algorithms can create static stereoscopic images with perceived depth control function to ensure a compelling 3D viewing experience without visual discomfort. However, current algorithms do not normally support standard Cinematic Storytelling techniques. These techniques, such as object movement, camera motion, and zooming, can result in dynamic scene depth change within and between a series of frames (shots) in stereoscopic cinematography. In this study, we empirically evaluate the following three types of stereoscopic imaging approaches that aim to address this problem. (1) Real-Eye Configuration: set camera separation equal to the nominal human eye interpupillary distance. The perceived depth on the display is identical to the scene depth without any distortion. (2) Mapping Algorithm: map the scene depth to a predefined range on the display to avoid excessive perceived depth. A new method that dynamically adjusts the depth mapping from scene space to display space is presented in addition to an existing fixed depth mapping method. (3) Depth of Field Simulation: apply Depth of Field (DOF) blur effect to stereoscopic images. Only objects that are inside the DOF are viewed in full sharpness. Objects that are far away from the focus plane are blurred. We performed a human-based trial using the ITU-R BT.500-11 Recommendation to compare the depth quality of stereoscopic video sequences generated by the above-mentioned imaging methods. Our results indicate that viewers' practical 3D viewing volumes are different for individual stereoscopic displays and viewers can cope with much larger perceived depth range in viewing stereoscopic cinematography in comparison to static stereoscopic images. Our new dynamic depth mapping method does have an advantage over the fixed depth mapping method in controlling stereo depth perception. The DOF blur effect does not provide the expected improvement for perceived depth quality control in 3D cinematography

Defining an additivity framework for mixture research in inducible whole-cell biosensors

DEFF Research Database (Denmark)

Martin-Betancor, K; Ritz, Christian; Fernández-Piñas, F

2015-01-01

A novel additivity framework for mixture effect modelling in the context of whole cell inducible biosensors has been mathematically developed and implemented in R. The proposed method is a multivariate extension of the effective dose (EDp) concept. Specifically, the extension accounts for differe......A novel additivity framework for mixture effect modelling in the context of whole cell inducible biosensors has been mathematically developed and implemented in R. The proposed method is a multivariate extension of the effective dose (EDp) concept. Specifically, the extension accounts...... for differential maximal effects among analytes and response inhibition beyond the maximum permissive concentrations. This allows a multivariate extension of Loewe additivity, enabling direct application in a biphasic dose-response framework. The proposed additivity definition was validated, and its applicability...... illustrated by studying the response of the cyanobacterial biosensor Synechococcus elongatus PCC 7942 pBG2120 to binary mixtures of Zn, Cu, Cd, Ag, Co and Hg. The novel method allowed by the first time to model complete dose-response profiles of an inducible whole cell biosensor to mixtures. In addition...

Neutron transport and Montecarlo method: analysis and revision

International Nuclear Information System (INIS)

Perlado, J.M.

1982-01-01

The resolution of the neutron transport equation by the Montecarlo method is presented. Coming from an extensive discussion on the best formulation of that equation in order to be treated through the mentioned method, the theoretical bases of the estimator and random-walk generation is extensively explained. The most general expression for the estimators in different physical situations, each with a diverse random-walk, is included in this basical theoretical part. Furthemore, a large revision on the variance reduction methods is made. Its theoretical presentation is claimed to be in connection with the need for each one of them. The use of the adjoint equation, as a part of the importance sampling, Russian Roulette, splitting, exponential transform, conditional and correlated Montecarlo, and one-collision and next-event extimators, are discussed. Finally, come comments in the presentation of the last works on the theoretical prediction of errors in the generation of estimators-random walks are made. (author)

A Collocation Method by Moving Least Squares Applicable to European Option Pricing

Directory of Open Access Journals (Sweden)

M. Amirfakhrian

2016-05-01

Full Text Available The subject matter of the present inquiry is the pricing of European options in the actual form of numbers. To assess the numerical prices of European options, a scheme independent of any kind of mesh but rather powered by moving least squares (MLS estimation is made. In practical terms, first the discretion of time variable is implemented and then, an MLS-powered method is applied for spatial approximation. As, unlike other methods, these courses of action mentioned here don't rely on a mesh, one can firmly claim they are to be categorized under mesh-less methods. And, of course, at the end of the paper, various experiments are offered to prove how efficient and how powerful the introduced approach is.

Success of lime additives for controlling SO2 releases from fluidized bed combustion units

International Nuclear Information System (INIS)

Muezzinoglu, A.; Bayram, A.; Odabasi, M.

1995-01-01

Purpose of this work was to study the desulfurization efficiencies of dry additives on the fluidized bed reactors fired with low quality lignites. In these tests selected initial SO 2 levels were in the order of 1000 ppm or less in the flue gases. Lime addition for desulfurization may either be made by mixing with the fuel or by injection into the combustion reactor. In fluidized bed combustion systems both methods are physically possible. In the fluidized combustion systems a third method of addition is also possible this, is by mixing dry additives with fluidizer sand. In this third method additives create a fluidizer effect as well as reacting with the sulfur oxides being formed during the combustion of fuel

PARALLEL AND ADAPTIVE UNIFORM-DISTRIBUTED REGISTRATION METHOD FOR CHANG’E-1 LUNAR REMOTE SENSED IMAGERY

Directory of Open Access Journals (Sweden)

X. Ning

2012-08-01

To resolve the above-mentioned registration difficulties, a parallel and adaptive uniform-distributed registration method for CE-1 lunar remote sensed imagery is proposed in this paper. Based on 6 pairs of randomly selected images, both the standard SIFT algorithm and the parallel and adaptive uniform-distributed registration method were executed, the versatility and effectiveness were assessed. The experimental results indicate that: by applying the parallel and adaptive uniform-distributed registration method, the efficiency of CE-1 lunar remote sensed imagery registration were increased dramatically. Therefore, the proposed method in the paper could acquire uniform-distributed registration results more effectively, the registration difficulties including difficult to obtain results, time-consuming, non-uniform distribution could be successfully solved.

Additives for cement compositions based on modified peat

Energy Technology Data Exchange (ETDEWEB)

Kopanitsa, Natalya, E-mail: kopanitsa@mail.ru; Sarkisov, Yurij, E-mail: sarkisov@tsuab.ru; Gorshkova, Aleksandra, E-mail: kasatkina.alexandra@gmail.com; Demyanenko, Olga, E-mail: angel-n@sibmail.com [Tomsk State University of Architecture and Building, 2, Solyanaya sq., Tomsk, 634003 (Russian Federation)

2016-01-15

High quality competitive dry building mixes require modifying additives for various purposes to be included in their composition. There is insufficient amount of quality additives having stable properties for controlling the properties of cement compositions produced in Russia. Using of foreign modifying additives leads to significant increasing of the final cost of the product. The cost of imported modifiers in the composition of the dry building mixes can be up to 90% of the material cost, depending on the composition complexity. Thus, the problem of import substitution becomes relevant, especially in recent years, due to difficult economic situation. The article discusses the possibility of using local raw materials as a basis for obtaining dry building mixtures components. The properties of organo-mineral additives for cement compositions based on thermally modified peat raw materials are studied. Studies of the structure and composition of the additives are carried out by physicochemical research methods: electron microscopy and X-ray analysis. Results of experimental research showed that the peat additives contribute to improving of cement-sand mortar strength and hydrophysical properties.

An optimized regulating method for composting phosphorus fractions transformation based on biochar addition and phosphate-solubilizing bacteria inoculation.

Science.gov (United States)

Wei, Yuquan; Zhao, Yue; Wang, Huan; Lu, Qian; Cao, Zhenyu; Cui, Hongyang; Zhu, Longji; Wei, Zimin

2016-12-01

The study was conducted to investigate the influence of biochar and/or phosphate-solubilizing bacteria (PSB) inoculants on microbial biomass, bacterial community composition and phosphorus (P) fractions during kitchen waste composting amended with rock phosphate (RP). There were distinct differences in the physic-chemical parameters, the proportion of P fractions and bacterial diversity in different treatments. The contribution of available P fractions increased during composting especially in the treatment with the addition of PSB and biochar. Redundancy analysis showed that bacterial compositions were significantly influenced by P content, inoculation and biochar. Variance partitioning further showed that synergy of inoculated PSB and indigenous bacterial communities and the joint effect between biochar and bacteria explained the largest two proportion of the variation in P fractions. Therefore, the combined application of PSB and biochar to improve the inoculation effect and an optimized regulating method were suggested based on the distribution of P fractions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Modified X-ray method of a study of duodenum

Energy Technology Data Exchange (ETDEWEB)

Korolyuk, I.P.; Bugakov, V.M.; Shinkin, V.M.

A modified X-ray examination of duodenum under hypotension conditions is described. In comparison with the existing method, the above-mentioned modification allows one to investigate the duodenum by using double contrast - the high-concentrated barium suspension and the gas, formed after the gasificated powder dose. 327 patients have been examined by the given method, 126 of them have been diagnosed to suffer from inflammatory diseases of the stomach and the duodenum, 22 of them suffering from the duodenum peptic ulcer, 107 of them - pancreatitis, 48-cholelithiasis, 24 - the tumor of the pancreatoduodenum zone. 65 patients have been operated on. Roentgenomorphologic comparisons have been carried out for 66 patients suffering from inflammatory deseases of the duodenum. Duodenum visualization of 283 patients is found to be good and satisfactory. The given method may be used under any conditions, including polyclinics, due to the sparing nature.

Ultrasonic assessment of additive manufactured Ti-6Al-4V

Science.gov (United States)

Schehl, Norman; Kramb, Vicki; Dierken, Josiah; Aldrin, John; Schwalbach, Edwin; John, Reji

2018-04-01

Additive Manufacturing (AM) processes offer the potential for manufacturing cost savings and rapid insertion into service through production of near net shape components for complicated structures. Use of these parts in high reliability applications such as those in the aerospace industry will require nondestructive characterization methods to ensure post-process material quality in as-built condition. Ultrasonic methods can be used for this quality verification. Depending on the application, the service life of AM components can be sensitive to the part surface condition. The surface roughness and layered structure inherent to the electron-beam powder-bed fusion process necessitates new approaches to evaluate subsurface material integrity in its presence. Experimental methods and data analytics may improve the evaluation of as-built additively manufactured materials. This paper discusses the assessment of additively manufactured EBM Ti-6Al-4V panels using ultrasonic methods and the data analytics applied to evaluate material integrity. The assessment was done as an exploratory study as the discontinuities of interest in these test samples were not known when the measurements were performed. Water immersion ultrasonic techniques, including pulse-echo and through transmission with 10 MHz focused transducers, were used to explore the material integrity of as-built plates. Subsequent destructive mechanical tests of specimens extracted from the plates provided fracture locations indicating critical flaws. To further understand the effect of surface-roughness, an evaluation of ultrasonic response in the presence of as-built surfaces and with the surface removed was performed. The assessment of additive manufactured EBM Ti-6Al-4V panels with ultrasonic techniques indicated that ultrasonic energy was attenuated by the as-built surface roughness. In addition, feature detection was shown to be sensitive to experimental ultrasonic parameters and flaw morphology.

Optimal boarding method for airline passengers

Energy Technology Data Exchange (ETDEWEB)

Steffen, Jason H.; /Fermilab

2008-02-01

Using a Markov Chain Monte Carlo optimization algorithm and a computer simulation, I find the passenger ordering which minimizes the time required to board the passengers onto an airplane. The model that I employ assumes that the time that a passenger requires to load his or her luggage is the dominant contribution to the time needed to completely fill the aircraft. The optimal boarding strategy may reduce the time required to board and airplane by over a factor of four and possibly more depending upon the dimensions of the aircraft. I explore some features of the optimal boarding method and discuss practical modifications to the optimal. Finally, I mention some of the benefits that could come from implementing an improved passenger boarding scheme.

Modern leadership and management methods for development organizations

Directory of Open Access Journals (Sweden)

Samosudova Natalia V.

2017-01-01

Full Text Available The following article represents an overview of the basic theoretical concepts of leadership and management in the framework of the organization. The main scientific approaches to leadership are described in conjunction with various leadership styles and their correlation with different levels of effectiveness as a result of the organization’s activity. Certain characteristics applicable to leaders and managers are mentioned. Attitude and obligations of a modern construction project manager are discussed, along with the challenges the construction industry represents these days. Ideas about methods of complex analysis for further research and identifying leadership tactics and their impact on the success of the development organization are suggested.

Determination of metal impurities in MOX powder by direct current arc atomic emission spectroscopy. Application of standard addition method for direct analysis of powder sample

International Nuclear Information System (INIS)

Furuse, Takahiro; Taguchi, Shigeo; Kuno, Takehiko; Surugaya, Naoki

2016-12-01

Metal impurities in MOX powder obtained from uranium and plutonium recovered from reprocessing process of spent nuclear fuel have to be determined for its characterization. Direct current arc atomic emission spectroscopy (DCA-AES) is one of the useful methods for direct analysis of powder sample without dissolving the analyte into aqueous solution. However, the selection of standard material, which can overcome concerns such as matrix matching, is quite important to create adequate calibration curves for DCA-AES. In this study, we apply standard addition method using the certified U_3O_8 containing known amounts of metal impurities to avoid the matrix problems. The proposed method provides good results for determination of Fe, Cr and Ni contained in MOX samples at a significant quantity level. (author)

TREATMENT OF TRANSCONDYLAR EXTENSOR FRACTURES OF THE HUMERUS IN CHILDREN: ON THE ISSUE OF HISTORY OF THE METHOD “COLLAR AND CUFF”

Directory of Open Access Journals (Sweden)

A. S. Zolotov

2013-01-01

Full Text Available The article is devoted to the history of one of the methods of conservative treatment humeral transcondylar extensor fractures in children - a method «collar and cuff». The second and very common name of this method is connected with the name of the american orthopaedist Walter Blount. «The method of Blount» is mentioned in many domestic and foreign sources. Nevertheless the analysis of publications on the history of the discussed method of treatment indicates the priority in this matter other famous doctor - British podiatrist Robert Jones.

Quantification Methods of Management Skills in Shipping

Directory of Open Access Journals (Sweden)

Riana Iren RADU

2012-04-01

Full Text Available Romania can not overcome the financial crisis without business growth, without finding opportunities for economic development and without attracting investment into the country. Successful managers find ways to overcome situations of uncertainty. The purpose of this paper is to determine the managerial skills developed by the Romanian fluvial shipping company NAVROM (hereinafter CNFR NAVROM SA, compared with ten other major competitors in the same domain, using financial information of these companies during the years 2005-2010. For carrying out the work it will be used quantification methods of managerial skills to CNFR NAVROM SA Galati, Romania, as example mentioning the analysis of financial performance management based on profitability ratios, net profit margin, suppliers management, turnover.

Aminocarminic acid in E120-labelled food additives and beverages.

Science.gov (United States)

Sabatino, Leonardo; Scordino, Monica; Gargano, Maria; Lazzaro, Francesco; Borzì, Marco A; Traulo, Pasqualino; Gagliano, Giacomo

2012-01-01

An analytical method was developed for investigating aminocarminic acid occurrence in E120-labelled red-coloured-beverages and in E120 additives, with the aim of controlling the purity of the carmine additive in countries where the use of aminocarminic acid is forbidden. The carminic acid and the aminocarminic acid were separated by high-performance liquid chromatography-photodiode array-tandem mass spectrography (HPLC-PDA-MS/MS). The method was statistically validated. The regression lines, ranging from 10 to 100 mg/L, showed r(2 )> 0.9996. Recoveries from 97% to 101% were obtained for the fortification level of 50 mg/L; the relative standard deviations did not exceed 3%. The LODs were below 2 mg/L, whereas the LOQs did not exceed 4 mg/L. The method was successfully applied to 27 samples of commercial E120-labelled red-coloured beverages and E120 additives, collected in Italy during quality control investigations conducted by the Ministry. The results demonstrated that more than 50% of the samples contained aminocarminic acid, evidencing the alarming illicit use of this semi-synthetic carmine acid derivative.

Comparative analysis of different methods for image enhancement

Institute of Scientific and Technical Information of China (English)

吴笑峰; 胡仕刚; 赵瑾; 李志明; 李劲; 唐志军; 席在芳

2014-01-01

Image enhancement technology plays a very important role to improve image quality in image processing. By enhancing some information and restraining other information selectively, it can improve image visual effect. The objective of this work is to implement the image enhancement to gray scale images using different techniques. After the fundamental methods of image enhancement processing are demonstrated, image enhancement algorithms based on space and frequency domains are systematically investigated and compared. The advantage and defect of the above-mentioned algorithms are analyzed. The algorithms of wavelet based image enhancement are also deduced and generalized. Wavelet transform modulus maxima (WTMM) is a method for detecting the fractal dimension of a signal, it is well used for image enhancement. The image techniques are compared by using the mean (μ), standard deviation (s), mean square error (MSE) and PSNR (peak signal to noise ratio). A group of experimental results demonstrate that the image enhancement algorithm based on wavelet transform is effective for image de-noising and enhancement. Wavelet transform modulus maxima method is one of the best methods for image enhancement.

The spectral method and ergodic theorems for general Markov chains

International Nuclear Information System (INIS)

Nagaev, S V

2015-01-01

We study the ergodic properties of Markov chains with an arbitrary state space and prove a geometric ergodic theorem. The method of the proof is new: it may be described as an operator method. Our main result is an ergodic theorem for Harris-Markov chains in the case when the return time to some fixed set has finite expectation. Our conditions for the transition function are more general than those used by Athreya-Ney and Nummelin. Unlike them, we impose restrictions not on the original transition function but on the transition function of an embedded Markov chain constructed from the return times to the fixed set mentioned above. The proof uses the spectral theory of linear operators on a Banach space

Pharmaceutical supply chain risk assessment in Iran using analytic hierarchy process (AHP) and simple additive weighting (SAW) methods.

Science.gov (United States)

Jaberidoost, Mona; Olfat, Laya; Hosseini, Alireza; Kebriaeezadeh, Abbas; Abdollahi, Mohammad; Alaeddini, Mahdi; Dinarvand, Rassoul

2015-01-01

Pharmaceutical supply chain is a significant component of the health system in supplying medicines, particularly in countries where main drugs are provided by local pharmaceutical companies. No previous studies exist assessing risks and disruptions in pharmaceutical companies while assessing the pharmaceutical supply chain. Any risks affecting the pharmaceutical companies could disrupt supply medicines and health system efficiency. The goal of this study was the risk assessment in pharmaceutical industry in Iran considering process's priority, hazard and probability of risks. The study was carried out in 4 phases; risk identification through literature review, risk identification in Iranian pharmaceutical companies through interview with experts, risk analysis through a questionnaire and consultation with experts using group analytic hierarchy process (AHP) method and rating scale (RS) and risk evaluation of simple additive weighting (SAW) method. In total, 86 main risks were identified in the pharmaceutical supply chain with perspective of pharmaceutical companies classified in 11 classes. The majority of risks described in this study were related to the financial and economic category. Also financial management was found to be the most important factor for consideration. Although pharmaceutical industry and supply chain were affected by current political conditions in Iran during the study time, but half of total risks in the pharmaceutical supply chain were found to be internal risks which could be fixed by companies, internally. Likewise, political status and related risks forced companies to focus more on financial and supply management resulting in less attention to quality management.

Decontamination formulation with sorbent additive

Science.gov (United States)

Tucker; Mark D. , Comstock; Robert H.

2007-10-16

A decontamination formulation and method of making that neutralizes the adverse health effects of both chemical and biological compounds, especially chemical warfare (CW) and biological warfare (BW) agents, and toxic industrial chemicals. The formulation provides solubilizing compounds that serve to effectively render the chemical and biological compounds, particularly CW and BW compounds, susceptible to attack, and at least one reactive compound that serves to attack (and detoxify or kill) the compound. The formulation includes at least one solubilizing agent, a reactive compound, a bleaching activator, a sorbent additive, and water. The highly adsorbent, water-soluble sorbent additive (e.g., sorbitol or mannitol) is used to "dry out" one or more liquid ingredients, such as the liquid bleaching activator (e.g., propylene glycol diacetate or glycerol diacetate) and convert the activator into a dry, free-flowing powder that has an extended shelf life, and is more convenient to handle and mix in the field.

[Analysis of phonosurgical methods of treatment in spasmodic dysphonia].

Science.gov (United States)

Kosztyła-Hojna, Bożena; Berger, Greta; Zdrojkowski, Maciej

2017-02-20

Spasmodic dysphonia (SD) is rather a rare voice disorder. It is most often seen in woman aged 40-50. The disease is caused by deep emotional and neurological disorders of extrapyramidal system. Two main clinical forms of SD are distinguished: about 90% of cases - adductor spasmodic dysphonia and abductor spasmodic dysphonia roughly 10%. Conservative therapy does not always yield sufficient effects. Botulinum toxin - type A injections into the thyroarytenoid muscle are also used in therapy. Though results are temporary and reversible. Among phonosurgical methods thyroplasty type II according to Isshiki and tyroarytenoid muscle myectomy (TAM) should be also mentioned among phonosurgical methods. The aim of the work is to evaluate results of conservative and phonosurgical treatment of SD. Spasmodic dysphonia markedly restricts communication process of patients and public relations both social and occupational.

Infill Optimization for Additive Manufacturing - Approaching Bone-like Porous Structures

DEFF Research Database (Denmark)

Wu, Jun; Aage, Niels; Westermann, Ruediger

2018-01-01

Porous structures such as trabecular bone are widely seen in nature. These structures exhibit superior mechanical properties whilst being lightweight. In this paper, we present a method to generate bone-like porous structures asl ightweight infill for additive manufacturing. Our method builds upon...

Double Michael Addition Reaction of Bischalcone under Ultrasound

Institute of Scientific and Technical Information of China (English)

LI,Ji-Tai; XU,Wen-Zhi; CHEN,Guo-Feng; LI,Tong-Shuang

2004-01-01

@@ The Michael addition of 1,5-diaryl-1,4-pentadien-3-ones with active methylene compounds has been the subjects of many investigations. Ultrasound has increasingly been used in organic synthesis in the last three decades. Compared with traditional methods, this method is more convenient and easily controlled. A large number of organic reactions can be carried out in higher yield, shorter reaction time or milder conditions under ultrasonic irradiation. KF/Al2O3 as a useful solid supported catalyst has received considerable attention because of their high level of chemoselectivity and environmental compatibility as well as simplicity of operation and their ready availability at low cost. Herein we report the double Michael addition of dibenzalacetone with active methlene compounds such as dimethyl malonate, diethyl malonate,methyl cyanoacetate and ethyl cyanoacetate catalyzed by KF/Al2O3 under ultrasound irradiation.

Effect of radiation resistance additives for insulation materials

International Nuclear Information System (INIS)

Yamamoto, Yasuaki; Yagyu, Hideki; Seguchi, Tadao.

1988-01-01

For the electric wires and cables used in radiation environment such as nuclear power stations and fuel reprocessing facilities, the properties of excellent radiation resistance are required. For these insulators and sheath materials, ethylene propylene rubber, polyethylene and other polymers have been used, but it cannot be said that they always have good radiation resistance. However, it has been well known that radiation resistance can be improved with small amount of additives, and heat resistance and burning retarding property as well as radiation resistance are given to the insulators of wires and cables for nuclear facilities by mixing various additives. In this research, the measuring method for quantitatively determining the effect of Anti-rad (radiation resistant additive) was examined. Through the measurement of gel fraction, radical formation and decomposed gas generation, the effect of Anti-rad protecting polymers from radiation deterioration was examined from the viewpoint of chemical reaction. The experimental method and the results are reported. The radiation energy for cutting C-H coupling is polymers is dispersed by Anti-rad, and the probability of cutting is lowered. Anti-rad catches and extinguishes radicals that start oxidation reaction. (K.I.)

Pruned-enriched Rosenbluth method: Simulations of θ polymers of chain length up to 1000000

International Nuclear Information System (INIS)

Grassberger, P.

1997-01-01

We present an algorithm for simulating flexible chain polymers. It combines the Rosenbluth-Rosenbluth method with recursive enrichment. Although it can be applied also in more general situations, it is most efficient for three-dimensional θ polymers on the simple-cubic lattice. There it allows high statistics simulations of chains of length up to N=10 6 . For storage reasons, this is feasable only for polymers in a finite volume. For free θ polymers in infinite volume, we present very high statistics runs with N=10000. These simulations fully agree with previous simulations made by Hegger and Grassberger [J. Chem. Phys. 102, 6681 (1995)] with a similar but less efficient algorithm, showing that logarithmic corrections to mean field behavior are much stronger than predicted by field theory. But the finite volume simulations show that the density inside a collapsed globule scales with the distance from the θ point as predicted by mean field theory, in contrast to claims in the work mentioned above. In addition to the simple-cubic lattice, we also studied two versions of the bond fluctuation model, but with much shorter chains. Finally, we show that our method can be applied also to off-lattice models, and illustrate this with simulations of a model studied in detail by Freire et al. [Macromolecules 19, 452 (1986) and later work]. copyright 1997 The American Physical Society

Additive Manufactured Superconducting Cavities

Science.gov (United States)

Holland, Eric; Rosen, Yaniv; Woolleet, Nathan; Materise, Nicholas; Voisin, Thomas; Wang, Morris; Mireles, Jorge; Carosi, Gianpaolo; Dubois, Jonathan

Superconducting radio frequency cavities provide an ultra-low dissipative environment, which has enabled fundamental investigations in quantum mechanics, materials properties, and the search for new particles in and beyond the standard model. However, resonator designs are constrained by limitations in conventional machining techniques. For example, current through a seam is a limiting factor in performance for many waveguide cavities. Development of highly reproducible methods for metallic parts through additive manufacturing, referred to colloquially as 3D printing\\x9D, opens the possibility for novel cavity designs which cannot be implemented through conventional methods. We present preliminary investigations of superconducting cavities made through a selective laser melting process, which compacts a granular powder via a high-power laser according to a digitally defined geometry. Initial work suggests that assuming a loss model and numerically optimizing a geometry to minimize dissipation results in modest improvements in device performance. Furthermore, a subset of titanium alloys, particularly, a titanium, aluminum, vanadium alloy (Ti - 6Al - 4V) exhibits properties indicative of a high kinetic inductance material. This work is supported by LDRD 16-SI-004.

Truth Space Method for Caching Database Queries

Directory of Open Access Journals (Sweden)

S. V. Mosin

2015-01-01

Full Text Available We propose a new method of client-side data caching for relational databases with a central server and distant clients. Data are loaded into the client cache based on queries executed on the server. Every query has the corresponding DB table – the result of the query execution. These queries have a special form called "universal relational query" based on three fundamental Relational Algebra operations: selection, projection and natural join. We have to mention that such a form is the closest one to the natural language and the majority of database search queries can be expressed in this way. Besides, this form allows us to analyze query correctness by checking lossless join property. A subsequent query may be executed in a client’s local cache if we can determine that the query result is entirely contained in the cache. For this we compare truth spaces of the logical restrictions in a new user’s query and the results of the queries execution in the cache. Such a comparison can be performed analytically , without need in additional Database queries. This method may be used to define lacking data in the cache and execute the query on the server only for these data. To do this the analytical approach is also used, what distinguishes our paper from the existing technologies. We propose four theorems for testing the required conditions. The first and the third theorems conditions allow us to define the existence of required data in cache. The second and the fourth theorems state conditions to execute queries with cache only. The problem of cache data actualizations is not discussed in this paper. However, it can be solved by cataloging queries on the server and their serving by triggers in background mode. The article is published in the author’s wording.

Evaluation of certain food additives and contaminants.

Science.gov (United States)

2013-01-01

This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives and a food contaminant with a view to concluding as to safety concerns and to preparing specifications for identity and purity. The first part of the report contains a general discussion of the principles governing the toxicological evaluation of and assessment of dietary exposure to food additives. A summary follows of the Committee's evaluations of technical, toxicological and dietary exposure data for seven food additives (advantame; glucoamylase from Trichoderma reesei expressed in Trichoderma reesei; glycerol ester of gum rosin; glycerol ester of tall oil rosin; glycerol ester of wood rosin; nisin; and octenyl succinic acid modified gum arabic) and an assessment of dietary exposure to cadmium from cocoa and cocoa products. Specifications for the following food additives were revised: annatto extracts (solvent-extracted bixin and solvent-extracted norbixin); Benzoe tonkinensis; food additives containing aluminium and/or silicon; mineral oil (medium viscosity); modified starches; paprika extract; phosphates (analytical methods for the determination of phosphorus and revision of specifications); 3-phytase from Aspergillus niger expressed in Aspergillus niger; potassium aluminium silicate; and potassium aluminium silicate-based pearlescent pigments. Annexed to the report are tables summarizing the Committee's recommendations for dietary exposures to and toxicological evaluations of the food additives and contaminant considered.

Non-Archimedean Hyers-Ulam Stability of an Additive-Quadratic Mapping

Directory of Open Access Journals (Sweden)

Hassan Azadi Kenary

2012-01-01

Full Text Available Using fixed point method and direct method, we prove the Hyers-Ulam stability of the following additive-quadratic functional equation 2((++/+2((−+/+2((+−/+2((−++/=4(+4(+4(, where is a positive real number, in non-Archimedean normed spaces.

Procedures of water desalination with solar energy and f-chart method

Directory of Open Access Journals (Sweden)

Petrović Andrija A.

2015-01-01

Full Text Available Due to rapid population growth, and climate change caused by environmental pollution needs for drinking water are increasing while amount of freshwater are decreasing. However possible solution for freshwater scarcity can be found in water desalination procedures. In this article three representative water desalination solar powered plants are described. Except explanation of processes it is also mentioned basic advantages and disadvantages of humidification, reverse osmosis and desalination evaporation by using solar energy. Simulation of the solar desalination system is analyzed with f-chart method monthly, located on located 42 degrees north latitude.

Investigation of plasma arc welding as a method for the additive manufacturing of titanium-(6)aluminum-(4)vanadium alloy components

Science.gov (United States)

Stavinoha, Joe N.

The process of producing near net-shape components by material deposition is known as additive manufacturing. All additive manufacturing processes are based on the addition of material with the main driving forces being cost reduction and flexibility in both manufacturing and product design. With wire metal deposition, metal is deposited as beads side-by-side and layer-by-layer in a desired pattern to build a complete component or add features on a part. There are minimal waste products, low consumables, and an efficient use of energy and feedstock associated with additive manufacturing processes. Titanium and titanium alloys are useful engineering materials that possess an extraordinary combination of properties. Some of the properties that make titanium advantageous for structural applications are its high strength-to-weight ratio, low density, low coefficient of thermal expansion, and good corrosion resistance. The most commonly used titanium alloy, Ti-6Al-4V, is typically used in aerospace applications, pressure vessels, aircraft gas turbine disks, cases and compressor blades, and surgical implants. Because of the high material prices associated with titanium alloys, the production of near net-shape components by additive manufacturing is an attractive option for the manufacturing of Ti-6Al-4V alloy components. In this thesis, the manufacturing of cylindrical Ti-6Al-4V alloy specimens by wire metal deposition utilizing the plasma arc welding process was demonstrated. Plasma arc welding is a cost effective additive manufacturing technique when compared to other current additive manufacturing methods such as laser beam welding and electron beam welding. Plasma arc welding is considered a high-energy-density welding processes which is desirable for the successful welding of titanium. Metal deposition was performed using a constant current plasma arc welding power supply, flow-purged welding chamber, argon shielding and orifice gas, ERTi-5 filler metal, and Ti-6Al

[The importance of memory bias in obtaining age of menarche by recall method in Brazilian adolescents].

Science.gov (United States)

Castilho, Silvia Diez; Nucci, Luciana Bertoldi; Assuino, Samanta Ramos; Hansen, Lucca Ortolan

2014-06-01

To compare the age at menarche obtained by recall method according to the time elapsed since the event, in order to verify the importance of the recall bias. Were evaluated 1,671 girls (7-18 years) at schools in Campinas-SP regarding the occurrence of menarche by the status quo method (menarche: yes or no) and the recall method (date of menarche, for those who mentioned it). The age at menarche obtained by the status quo method was calculated by logit, which considers the whole group, and the age obtained by the recall method was calculated as the average of the mentioned age at menarche. In this group, the age at menarche was obtained by the difference between the date of the event and the date of birth. Girls who reported menarche (883, 52.8%) were divided into four groups according to the time elapsed since the event. To analyze the results, we used ANOVA and logistic regression for the analysis, with a significance level of 0.05. The age at menarche calculated by logit was 12.14 y/o (95% CI 12.08 to 12.20). Mean ages obtained by recall were: for those who experienced menarche within the previous year 12.26 y/o (±1.14), between > 1-2 years before, 12.29 y (±1.22); between > 2-3 years before, 12.23 y/o (±1.27); and more than 3 years before, 11.55y/o (±1.24), p recall method was similar for girls who menstruated within the previous 3 years (and approaches the age calculated by logit); when more than 3 years have passed, the recall bias was significant.

Additive effects of dietary glycotoxins and androgen excess on the kidney of a female rat model

Directory of Open Access Journals (Sweden)

Sotiria Palimeri

2016-06-01

Conclusions: The above mentioned data suggest that dietary glycotoxins, in combination with increased androgen exposure, exert a more profound negative impact on the kidney of an androgenized female rat model that mimics the metabolic characteristics of polycystic ovary syndrome.

Development of an evaluation method for the quality of NPP MCR operators' communication using Work Domain Analysis (WDA)

International Nuclear Information System (INIS)

Jang, Inseok; Park, Jinkyun; Seong, Poonghyun

2011-01-01

Research highlights: → No evaluation method is available for operators' communication quality in NPPs. → To model this evaluation method, the Work Domain Analysis (WDA) method was found. → This proposed method was applied to NPP MCR operators. → The quality of operators' communication can be evaluated with the propose method. - Abstract: The evolution of work demands has seen industrial evolution itself evolve into the computerization of these demands, making systems more complex. This field is now known as the Complex Socio-Technical System. As communication failures are problems associated with Complex Socio-Technical Systems, it has been discovered that communication failures are the cause of many incidents and accidents in various industries, including the nuclear, aerospace and railway industries. Despite the fact that there have been many studies on the severity of communication failures, there is no evaluation method for operators' communication quality in Nuclear Power Plants (NPPs). Therefore, the objectives of this study are to develop an evaluation method for the quality of NPP Main Control Room (MCR) operators' communication and to apply the proposed method to operators in a full-scope simulator. To develop the proposed method, the Work Domain Analysis (WDA) method is introduced. Several characteristics of WDA, including Abstraction Decomposition Space (ADS) and the diagonal of ADS are the important points in developing an evaluation method for the quality of NPP MCR operators' communication. In addition, to apply the proposed method, nine teams working in NPPs participated in a field simulation. The results of this evaluation reveal that operators' communication quality improved as a greater proportion of the components in the developed evaluation criteria were mentioned. Therefore, the proposed method could be useful for evaluating the communication quality in any complex system.

Do reading additions improve reading in pre-presbyopes with low vision?

Science.gov (United States)

Alabdulkader, Balsam; Leat, Susan

2012-09-01

This study compared three different methods of determining a reading addition and the possible improvement on reading performance in children and young adults with low vision. Twenty-eight participants with low vision, aged 8 to 32 years, took part in the study. Reading additions were determined with (a) a modified Nott dynamic retinoscopy, (b) a subjective method, and (c) an age-based formula. Reading performance was assessed with MNREAD-style reading charts at 12.5 cm, with and without each reading addition in random order. Outcome measures were reading speed, critical print size, MNREAD threshold, and the area under the reading speed curve. For the whole group, there was no significant improvement in reading performance with any of the additions. When participants with normal accommodation at 12.5 cm were excluded, the area under the reading speed curve was significantly greater with all reading additions compared with no addition (p = 0.031, 0.028, and 0.028, respectively). Also, the reading acuity threshold was significantly better with all reading additions compared with no addition (p = 0.014, 0.030, and 0.036, respectively). Distance and near visual acuity, age, and contrast sensitivity did not predict improvement with a reading addition. All, but one, of the participants who showed a significant improvement in reading with an addition had reduced accommodation. A reading addition may improve reading performance for young people with low vision and should be considered as part of a low vision assessment, particularly when accommodation is reduced.

Fulltext PDF

Indian Academy of Sciences (India)

mention that about a decade later, using the method of lunar occultation to determine the structure of weak radio sources with the Ooty Radio Telescope, Govind Swarup (MNRAS, 172, 501, 1975) and Vijay Kapahi. (MNRAS, 172, 513, 1975) lent additional support to the big-bang or evolutionary model of the Universe.

Methods for Geometric Data Validation of 3d City Models

Science.gov (United States)

Wagner, D.; Alam, N.; Wewetzer, M.; Pries, M.; Coors, V.

2015-12-01

Geometric quality of 3D city models is crucial for data analysis and simulation tasks, which are part of modern applications of the data (e.g. potential heating energy consumption of city quarters, solar potential, etc.). Geometric quality in these contexts is however a different concept as it is for 2D maps. In the latter case, aspects such as positional or temporal accuracy and correctness represent typical quality metrics of the data. They are defined in ISO 19157 and should be mentioned as part of the metadata. 3D data has a far wider range of aspects which influence their quality, plus the idea of quality itself is application dependent. Thus, concepts for definition of quality are needed, including methods to validate these definitions. Quality on this sense means internal validation and detection of inconsistent or wrong geometry according to a predefined set of rules. A useful starting point would be to have correct geometry in accordance with ISO 19107. A valid solid should consist of planar faces which touch their neighbours exclusively in defined corner points and edges. No gaps between them are allowed, and the whole feature must be 2-manifold. In this paper, we present methods to validate common geometric requirements for building geometry. Different checks based on several algorithms have been implemented to validate a set of rules derived from the solid definition mentioned above (e.g. water tightness of the solid or planarity of its polygons), as they were developed for the software tool CityDoctor. The method of each check is specified, with a special focus on the discussion of tolerance values where they are necessary. The checks include polygon level checks to validate the correctness of each polygon, i.e. closeness of the bounding linear ring and planarity. On the solid level, which is only validated if the polygons have passed validation, correct polygon orientation is checked, after self-intersections outside of defined corner points and edges

Nanometer, submicron and micron sized aluminum powder prepared by semi-solid mechanical stirring method with addition of ceramic particles

International Nuclear Information System (INIS)

Qin, X.H.; Jiang, D.L.; Dong, S.M.

2004-01-01

Composite powder, which is a mixture of Al/Al 2 O 3 composite particles and nanometer, submicron and micron sized aluminum powder, was prepared by semi-solid mechanical stirring method with addition of Al 2 O 3 ceramic particles. The ceramic particles have an average diameter of 80 μm and a volume fraction of 15% in the slurry. The methods used to measure the size distribution of particles greater than 50 μm and less than 50 μm were sieve analysis and photosedimentation, respectively. The surface morphology and transverse sections of the composite powder of different sizes were examined by scanning electron microscope (SEM), optical microscope and auger electron spectroscopy (AES). The results indicate that the composite powder prepared in present work have a wide size distribution ranging from less than 50-900 μm, and the aluminum particles and Al/Al 2 O 3 composite particles are separated and isolated. The particles greater than 200 μm and less than 50 μm are almost pure aluminum powder. The rate of conversion of ingot aluminum into particles less than 1 μm containing nanometer and submicron sizes is 1.777 wt.% in this work. The aluminum powder of different sizes has different shape and surface morphology, quasi-spherical in shape with rough surface for aluminum particles of micron scale, irregular in shape for aluminum particles of submicron scale, and quite close to a globular or an excellent globular in shape for aluminum particles of nanometer size. On the other hand, the surface of ceramic particle was coated by aluminum particles with maximum thickness less than 10 μm containing nanometer and submicron sizes as a single layer. It is suggested that the surface of ceramic particles can provide more nucleation sites for solidification of liquid aluminum and the nucleation of liquid aluminum can take place readily, grow and adhere on the surface of ceramic particles, although it is poorly wetted by the liquid aluminum and the semi-solid slurry can

Development and Validation of HPLC Method for the Simultaneous Determination of Five Food Additives and Caffeine in Soft Drinks

Directory of Open Access Journals (Sweden)

Bürge Aşçı

2016-01-01

Full Text Available Box-Behnken design was applied to optimize high performance liquid chromatography (HPLC conditions for the simultaneous determination of potassium sorbate, sodium benzoate, carmoisine, allura red, ponceau 4R, and caffeine in commercial soft drinks. The experimental variables chosen were pH (6.0–7.0, flow rate (1.0–1.4 mL/min, and mobile phase ratio (85–95% acetate buffer. Resolution values of all peak pairs were used as a response. Stationary phase was Inertsil OctaDecylSilane- (ODS- 3V reverse phase column (250 × 4.6 mm, 5 μm dimensions. The detection was performed at 230 nm. Optimal values were found 6.0 pH, 1.0 mL/min flow rate, and 95% mobile phase ratio for the method which was validated by calculating the linearity (r2>0.9962, accuracy (recoveries ≥ 95.75%, precision (intraday variation ≤ 1.923%, interday variation ≤ 1.950%, limits of detection (LODs, and limits of quantification (LOQs parameters. LODs and LOQs for analytes were in the range of 0.10–0.19 μg/mL and 0.33–0.63 μg/mL, respectively. The proposed method was applied successfully for the simultaneous determination of the mixtures of five food additives and caffeine in soft drinks.

Additive Design and Manufacturing of Jet Engine Parts

Directory of Open Access Journals (Sweden)

Pinlian Han

2017-10-01

Full Text Available The additive design (AD and additive manufacturing (AM of jet engine parts will revolutionize the traditional aerospace industry. The unique characteristics of AM, such as gradient materials and micro-structures, have opened up a new direction in jet engine design and manufacturing. Engineers have been liberated from many constraints associated with traditional methodologies and technologies. One of the most significant features of the AM process is that it can ensure the consistency of parts because it starts from point(s, continues to line(s and layer(s, and ends with the competed part. Collaboration between design and manufacturing is the key to success in fields including aerodynamics, thermodynamics, structural integration, heat transfer, material development, and machining. Engineers must change the way they design a part, as they shift from the traditional method of “subtracting material” to the new method of “adding material” in order to manufacture a part. AD is not the same as designing for AM. A new method and new tools are required to assist with this new way of designing and manufacturing. This paper discusses in detail what is required in AD and AM, and how current problems can be solved.

Why Older Adults Spend Time Sedentary and Break Their Sedentary Behavior: A Mixed-Methods Approach Using Life-Logging Equipment.

Science.gov (United States)

Dontje, Manon L; Leask, Calum F; Harvey, Juliet; Skelton, Dawn A; Chastin, Sebastien F M

2018-04-01

Older adults are recommended to reduce their sedentary time to promote healthy ageing. To develop effective interventions identifying when, why, and how older adults are able to change their sitting habits is important. The aim of this mixed-method study was to improve our understanding of reasons for (breaking) sedentary behavior in older adults. Thirty older adults (74.0 [±5.3] years old, 73% women) were asked about their believed reasons for (breaking) sedentary behavior, and about their actual reasons when looking at a personal storyboard with objective records of activPAL monitor data and time-lapse camera pictures showing all their periods of sedentary time in a day. The most often mentioned believed reason for remaining sedentary was television/radio (mentioned by 48.3%), while eating/drinking was most often mentioned as actual reason (96.6%). Only 17.2% believed that food/tea preparation was a reason to break up sitting, while this was an actual reason for 82.8% of the study sample. Results of this study show that there is a discrepancy between believed and actual reasons for (breaking) sedentary behavior. These findings suggest developing interventions utilizing the actual reasons for breaking sedentary behavior to reduce sedentary time in older adults.

From Discrete Space-Time to Minkowski Space: Basic Mechanisms, Methods and Perspectives

Science.gov (United States)

Finster, Felix

This survey article reviews recent results on fermion systems in discrete space-time and corresponding systems in Minkowski space. After a basic introduction to the discrete setting, we explain a mechanism of spontaneous symmetry breaking which leads to the emergence of a discrete causal structure. As methods to study the transition between discrete space-time and Minkowski space, we describe a lattice model for a static and isotropic space-time, outline the analysis of regularization tails of vacuum Dirac sea configurations, and introduce a Lorentz invariant action for the masses of the Dirac seas. We mention the method of the continuum limit, which allows to analyze interacting systems. Open problems are discussed.

THE USE OF AHP METHOD IN THE MULTI‐CRITERIA TASK SOLVING PROCESS – CASE STUDY

Directory of Open Access Journals (Sweden)

Zygmunt KORBAN

2014-01-01

Full Text Available In the decision‐making process, both single‐ and multi‐criteria tasks are dealt with. In the majority of cases, the selection of a solution comes down to determination of the “best” decision (most often based on the subjective assessment or to organisation of the set of decisions. The Analytic Hierarchy Process (AHP is one of the methods used for evaluation of qualitative features in the multi‐criteria optimisation processes. This article discusses the possibilities of using the above‐mentioned method, illustrated with an example of purchasing technical equipment for one of the municipal landfill sites in the Silesian Province.

Verification of a Novel Method of Detecting Faults in Medium-Voltage Systems with Covered Conductors

Directory of Open Access Journals (Sweden)

Mišák Stanislav

2017-06-01

Full Text Available This paper describes the use of new methods of detecting faults in medium-voltage overhead lines built of covered conductors. The methods mainly address such faults as falling of a conductor, contacting a conductor with a tree branch, or falling a tree branch across three phases of a medium-voltage conductor. These faults cannot be detected by current digital relay protection systems. Therefore, a new system that can detect the above mentioned faults was developed. After having tested its operation, the system has already been implemented to protect mediumvoltage overhead lines built of covered conductors.

An alternative method to record rising temperatures during dental implant site preparation: a preliminary study using bovine bone

Directory of Open Access Journals (Sweden)

Domenica Laurito

2010-12-01

Full Text Available Overheating is constantly mentioned as a risk factor for bone necrosis that could compromise the dental implant primary stability. Uncontrolled thermal injury can result in a fibrous tissue, interpositioned at the implant-bone interface, compromising the long-term prognosis. The methods used to record temperature rise include either direct recording by thermocouple instruments or indirect estimating by infrared thermography. This preliminary study was carried out using bovine bone and a different method of temperatures rising estimation is presented. Two different types of drills were tested using fluoroptic thermometer and the effectiveness of this alternative temperature recording method was evaluated.

Advanced glycation end products, physico-chemical and sensory characteristics of cooked lamb loins affected by cooking method and addition of flavour precursors

DEFF Research Database (Denmark)

Roldan, Mar; Loebner, Jürgen; Degen, Julia

2015-01-01

The influence of the addition of a flavour enhancer solution (FES) (d-glucose, d-ribose, l-cysteine and thiamin) and of sous-vide cooking or roasting on moisture, cooking loss, instrumental colour, sensory characteristics and formation of Maillard reaction (MR) compounds in lamb loins was studied....... FES reduced cooking loss and increased water content in sous-vide samples. FES and cooking method showed a marked effect on browning development, both on the meat surface and within. FES led to tougher and chewier texture in sous-vide cooked lamb, and enhanced flavour scores of sous-vide samples more...

Use of Angle Model to Understand Addition and Subtraction of Fractions

Directory of Open Access Journals (Sweden)

Muzwangowenyu Mukwambo

2018-02-01

Full Text Available Learners in lower primary and even some in upper primary grades grapple to perform mathematical operations which involve fractions. Failure to solve these mathematical operations creates a gap in the teaching and learning processes of mathematics. We opine that this is attributed to use of traditional mathematical approaches of teaching and learning (TMATL of operations of fraction. With the hope of engaging the reformed mathematical approach of teaching and learning (RMATL this study investigated the following: How can trainee teachers use the angle model in RMATL operations of fractions? What are the perceptions of trainee teachers in the use of the angle model which engages RMATL to teach the operations of fractions? With the goal to fill the mentioned gap in which learners struggle to perform operations involving fractions, we observed and analysed worksheets on operation with fractions students wrote. Observations and interviews with trainee teachers of lower primary revealed poor performance in problems related to operations with fractions. Observed patterns supported by cognitivism revealed that invented methods or strategies on which RMATL is anchored are suitable enough to engage learner–centred teaching and learning which can prevent the abstractness of the concept of operations with fractions.

2015 Summer Design Challenge: Team A&E (2241) Additively Manufactured Discriminator.

Energy Technology Data Exchange (ETDEWEB)

Miller, Sarah E. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Moore, Brandon James [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

2016-11-01

Current discriminator designs are based on historical designs and traditional manufacturing methods. The goal of this project was to form non-traditional groups to create novel discriminator designs by taking advantage of additive manufacturing. These designs would expand current discriminator designs and provide insight on the applicability of additive manufacturing for future projects. Our design stretched the current abilities of additive manufacturing and noted desired improvements for the future. Through collaboration with NSC, we noted several additional technologies which work well with additive manufacturing such as topology optimization and CT scanning and determined how these technologies could be improved to better combine with additive manufacturing.

Magma addition rates in continental arcs: New methods of calculation and global implications

Science.gov (United States)

Ratschbacher, B. C.; Paterson, S. R.

2017-12-01

The transport of mass, heat and geochemical constituents (elements and volatiles) from the mantle to the atmosphere occurs via magma addition to the lithosphere. Calculation of magma addition rates (MARs) in continental arcs based on exposed proportions of igneous arc rocks is complex and rarely consistently determined. Multiple factors influence MAR calculations such as crust versus mantle contributions to magmas, a change in MARs across the arc and with depths throughout the arc crustal column, `arc tempos' with periods of high and low magmatic activity, the loss of previous emplaced arc rocks by subsequent magmatism and return to the mantle, arc migration, variations in the intrusive versus extrusive additions and evolving arc widths and thicknesses during tectonism. All of these factors need to be considered when calculating MARs.This study makes a new attempt to calculate MARs in continental arcs by studying three arc sections: the Famatinian arc, Argentina, the Sierra Nevada batholith, California and the Coast Mountain batholith, Washington and British Columbia. Arcs are divided into fore-arc, main arc and back arc sections and `boxes' with a defined width, length and thickness spanning upper middle and lower crustal levels are assigned to each section. Representative exposed crustal slices for each depth are then used to calculate MARs based on outcrop proportions for each box. Geochemical data is used to infer crustal recycling percentages and total thickness of the arc. Preliminary results show a correlation between MARs, crustal thicknesses and magmatic flare-up durations. For instance, the Famatinian arc shows a strong decrease in MARs between the main arc section (9.4 km3/Ma/arc-km) and the fore-arc (0.61 km3/Ma/arc-km) and back-arc (1.52 km3/Ma/arc-km) regions and an increase in the amount of magmatism with depth.Global MARs over geologic timescales have the potential to investigate mantle melt generation rates and the volatile outgassing contribution

A bootstrapping method for development of Treebank

Science.gov (United States)

Zarei, F.; Basirat, A.; Faili, H.; Mirain, M.

2017-01-01

Using statistical approaches beside the traditional methods of natural language processing could significantly improve both the quality and performance of several natural language processing (NLP) tasks. The effective usage of these approaches is subject to the availability of the informative, accurate and detailed corpora on which the learners are trained. This article introduces a bootstrapping method for developing annotated corpora based on a complex and rich linguistically motivated elementary structure called supertag. To this end, a hybrid method for supertagging is proposed that combines both of the generative and discriminative methods of supertagging. The method was applied on a subset of Wall Street Journal (WSJ) in order to annotate its sentences with a set of linguistically motivated elementary structures of the English XTAG grammar that is using a lexicalised tree-adjoining grammar formalism. The empirical results confirm that the bootstrapping method provides a satisfactory way for annotating the English sentences with the mentioned structures. The experiments show that the method could automatically annotate about 20% of WSJ with the accuracy of F-measure about 80% of which is particularly 12% higher than the F-measure of the XTAG Treebank automatically generated from the approach proposed by Basirat and Faili [(2013). Bridge the gap between statistical and hand-crafted grammars. Computer Speech and Language, 27, 1085-1104].

Advanced glycation end products, physico-chemical and sensory characteristics of cooked lamb loins affected by cooking method and addition of flavour precursors.

Science.gov (United States)

Roldan, Mar; Loebner, Jürgen; Degen, Julia; Henle, Thomas; Antequera, Teresa; Ruiz-Carrascal, Jorge

2015-02-01

The influence of the addition of a flavour enhancer solution (FES) (d-glucose, d-ribose, l-cysteine and thiamin) and of sous-vide cooking or roasting on moisture, cooking loss, instrumental colour, sensory characteristics and formation of Maillard reaction (MR) compounds in lamb loins was studied. FES reduced cooking loss and increased water content in sous-vide samples. FES and cooking method showed a marked effect on browning development, both on the meat surface and within. FES led to tougher and chewier texture in sous-vide cooked lamb, and enhanced flavour scores of sous-vide samples more markedly than in roasted ones. FES added meat showed higher contents of furosine; 1,2-dicarbonyl compounds and 5-hydroxymethylfurfural did not reach detectable levels. N-ε-carboxymethyllysine amounts were rather low and not influenced by the studied factors. Cooked meat seems to be a minor dietary source of MR products, regardless the presence of reducing sugars and the cooking method. Copyright © 2014 Elsevier Ltd. All rights reserved.

The teratology testing of food additives.

Science.gov (United States)

Barrow, Paul C; Spézia, François

2013-01-01

The developmental and reproductive toxicity testing (including teratogenicity) of new foods and food additives is performed worldwide according to the guidelines given in the FDA Redbook. These studies are not required for substances that are generally recognized as safe, according to the FDA inventory. The anticipated cumulated human exposure level above which developmental or reproduction studies are required depends on the structure-alert category. For food additives of concern, both developmental (prenatal) and reproduction (multigeneration) studies are required. The developmental studies are performed in two species, usually the rat and the rabbit. The reproduction study is generally performed in the rat. The two rat studies are preferably combined into a single experimental design, if possible. The test methods described in the FDA Redbook are similar to those specified by the OECD for the reproductive toxicity testing of chemicals.

Subcriticality determination of nuclear fuel assembly by Mihalczo method

International Nuclear Information System (INIS)

Yamane, Yoshihiro; Watanabe, Shoji; Nishina, Kojiro; Miyoshi, Yoshinori; Suzaki, Takenori; Kobayashi, Iwao.

1986-01-01

To establish a technique of on-site subcriticality determination suitable for the criticality safety management of nuclear fuel assembly, the applicability of the method proposed by Mihalczo was examined with the Tank-type Critical Assembly (TCA) of the Japan Atomic Energy Research Institute. In the Mihalczo method, cross power spectral densities and auto power spectral densities are evaluated from the output currents of an ionization chamber containing 252 Cf neutron source and two neutron detectors. The principle of this method is that the spectral ratio formed by the power spectral densities mentioned can be related to the subcriticality by the help of a stochastic theory. Throughout our data processing, an improved formula taking account of the neutron extinction at a detection process was used. Up to the subcriticality of 15 dollars, the Mihalczo method agreed with the water-level worth method, which has been a standard method of reactivity determination at the TCA facility. The systems treated in the present report hold symmetry concerning the nuclear fuel configuration and the 252 Cf chamber position. It was clarified that, contrary to Mihalczo's assertion, the factor converting the spectral ratio to a subcriticality depends on subcriticality itself. (author)

Validation of transport models using additive flux minimization technique

Energy Technology Data Exchange (ETDEWEB)

Pankin, A. Y.; Kruger, S. E. [Tech-X Corporation, 5621 Arapahoe Ave., Boulder, Colorado 80303 (United States); Groebner, R. J. [General Atomics, San Diego, California 92121 (United States); Hakim, A. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543-0451 (United States); Kritz, A. H.; Rafiq, T. [Department of Physics, Lehigh University, Bethlehem, Pennsylvania 18015 (United States)

2013-10-15

A new additive flux minimization technique is proposed for carrying out the verification and validation (V and V) of anomalous transport models. In this approach, the plasma profiles are computed in time dependent predictive simulations in which an additional effective diffusivity is varied. The goal is to obtain an optimal match between the computed and experimental profile. This new technique has several advantages over traditional V and V methods for transport models in tokamaks and takes advantage of uncertainty quantification methods developed by the applied math community. As a demonstration of its efficiency, the technique is applied to the hypothesis that the paleoclassical density transport dominates in the plasma edge region in DIII-D tokamak discharges. A simplified version of the paleoclassical model that utilizes the Spitzer resistivity for the parallel neoclassical resistivity and neglects the trapped particle effects is tested in this paper. It is shown that a contribution to density transport, in addition to the paleoclassical density transport, is needed in order to describe the experimental profiles. It is found that more additional diffusivity is needed at the top of the H-mode pedestal, and almost no additional diffusivity is needed at the pedestal bottom. The implementation of this V and V technique uses the FACETS::Core transport solver and the DAKOTA toolkit for design optimization and uncertainty quantification. The FACETS::Core solver is used for advancing the plasma density profiles. The DAKOTA toolkit is used for the optimization of plasma profiles and the computation of the additional diffusivity that is required for the predicted density profile to match the experimental profile.

Validation of transport models using additive flux minimization technique

International Nuclear Information System (INIS)

Pankin, A. Y.; Kruger, S. E.; Groebner, R. J.; Hakim, A.; Kritz, A. H.; Rafiq, T.

2013-01-01

A new additive flux minimization technique is proposed for carrying out the verification and validation (V and V) of anomalous transport models. In this approach, the plasma profiles are computed in time dependent predictive simulations in which an additional effective diffusivity is varied. The goal is to obtain an optimal match between the computed and experimental profile. This new technique has several advantages over traditional V and V methods for transport models in tokamaks and takes advantage of uncertainty quantification methods developed by the applied math community. As a demonstration of its efficiency, the technique is applied to the hypothesis that the paleoclassical density transport dominates in the plasma edge region in DIII-D tokamak discharges. A simplified version of the paleoclassical model that utilizes the Spitzer resistivity for the parallel neoclassical resistivity and neglects the trapped particle effects is tested in this paper. It is shown that a contribution to density transport, in addition to the paleoclassical density transport, is needed in order to describe the experimental profiles. It is found that more additional diffusivity is needed at the top of the H-mode pedestal, and almost no additional diffusivity is needed at the pedestal bottom. The implementation of this V and V technique uses the FACETS::Core transport solver and the DAKOTA toolkit for design optimization and uncertainty quantification. The FACETS::Core solver is used for advancing the plasma density profiles. The DAKOTA toolkit is used for the optimization of plasma profiles and the computation of the additional diffusivity that is required for the predicted density profile to match the experimental profile

Additive Manufacturing Cloud via Peer-Robot Collaboration

Directory of Open Access Journals (Sweden)

Yuan Yao

2016-05-01

Full Text Available When building a 3D printing cloud manufacturing platform, self-sensing and collaboration on manufacturing resources present challenging problems. This paper proposes a peer-robot collaboration framework to deal with these issues. Each robot combines heterogeneous additive manufacturing hardware and software, acting as an intelligent agent. Through collaboration with other robots, it forms a dynamic and scalable integration manufacturing system. The entire distributed system is managed by rules that employ an internal rule engine, which supports rule conversion and conflict resolution. Two additive manufacturing service scenarios are designed to analyse the efficiency and scalability of the framework. Experiments show that the presented method performs well in tasks requiring large-scale access to resources and collaboration.

Analysis of wear of antifriction bearing using radioisotope method

International Nuclear Information System (INIS)

Bejcek, V.

1986-01-01

The time course was studied of the wear of one type of antifriction bearing in dependence on the thickness of lubricating film for five types of lubricating oil. The theory is described of the development of lubricating film, the experiment and its evaluation, and a detailed list is given of numerical results and practical conclusions. Briefly mentioned is the principle of the radioisotope method which has been described elsewhere: prior to the experiment the balls of the bearing were activated with a neutron beam from a nuclear reactor and the wear was determined from the activity of the worn material carried away by the lubricant. (A.K.)

Development of K-Nearest Neighbour Regression Method in Forecasting River Stream Flow

Directory of Open Access Journals (Sweden)

Mohammad Azmi

2012-07-01

Full Text Available Different statistical, non-statistical and black-box methods have been used in forecasting processes. Among statistical methods, K-nearest neighbour non-parametric regression method (K-NN due to its natural simplicity and mathematical base is one of the recommended methods for forecasting processes. In this study, K-NN method is explained completely. Besides, development and improvement approaches such as best neighbour estimation, data transformation functions, distance functions and proposed extrapolation method are described. K-NN method in company with its development approaches is used in streamflow forecasting of Zayandeh-Rud Dam upper basin. Comparing between final results of classic K-NN method and modified K-NN (number of neighbour 5, transformation function of Range Scaling, distance function of Mahanalobis and proposed extrapolation method shows that modified K-NN in criteria of goodness of fit, root mean square error, percentage of volume of error and correlation has had performance improvement 45% , 59% and 17% respectively. These results approve necessity of applying mentioned approaches to derive more accurate forecasts.

An effective method on pornographic images realtime recognition

Science.gov (United States)

Wang, Baosong; Lv, Xueqiang; Wang, Tao; Wang, Chengrui

2013-03-01

In this paper, skin detection, texture filtering and face detection are used to extract feature on an image library, training them with the decision tree arithmetic to create some rules as a decision tree classifier to distinguish an unknown image. Experiment based on more than twenty thousand images, the precision rate can get 76.21% when testing on 13025 pornographic images and elapsed time is less than 0.2s. This experiment shows it has a good popularity. Among the steps mentioned above, proposing a new skin detection model which called irregular polygon region skin detection model based on YCbCr color space. This skin detection model can lower the false detection rate on skin detection. A new method called sequence region labeling on binary connected area can calculate features on connected area, it is faster and needs less memory than other recursive methods.

Minimum Compliance Topology Optimization of Shell-Infill Composites for Additive Manufacturing

DEFF Research Database (Denmark)

Wu, Jun; Clausen, Anders; Sigmund, Ole

2017-01-01

Additively manufactured parts are often composed of two sub-structures, a solid shell forming their exterior and a porous infill occupying the interior. To account for this feature this paper presents a novel method for generating simultaneously optimized shell and infill in the context of minimum...... interpolation model into a physical density field, upon which the compliance is minimized. Enhanced by an adapted robust formulation for controlling the minimum length scale of the base, our method generates optimized shell-infill composites suitable for additive manufacturing. We demonstrate the effectiveness...

Evaluation of Advanced Polymers for Additive Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Rios, Orlando [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Carter, William G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kutchko, Cindy [PPG Industries, Pittsburgh, PA (United States); Fenn, David [PPG Industries, Pittsburgh, PA (United States); Olson, Kurt [PPG Industries, Pittsburgh, PA (United States)

2017-09-08

The goal of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Oak Ridge National Laboratory (ORNL) and PPG Industries, Inc. (PPG) was to evaluate the feasibility of using conventional coatings chemistry and technology to build up material layer-by-layer. The PPG-ORNL study successfully demonstrated that polymeric coatings formulations may overcome many limitations of common thermoplastics used in additive manufacturing (AM), allow lightweight nozzle design for material deposition, and increase build rate. The materials effort focused on layer-by-layer deposition of coatings with each layer fusing together. The combination of materials and deposition results in an additively manufactured build that has sufficient mechanical properties to bear the load of additional layers, yet is capable of bonding across the z-layers to improve build direction strength. The formulation properties were tuned to enable a novel, high-throughput deposition method that is highly scalable, compatible with high loading of reinforcing fillers, and inherently low-cost.

Selecting parts for additive manufacturing in service logistics

NARCIS (Netherlands)

Knofius, Nils; van der Heijden, Matthijs C.; Zijm, Willem H.M.

2016-01-01

Purpose For more than ten years, the value of additive manufacturing (AM) for after-sales service logistics has been propagated. Today, however, only few applications are observed in practice. In this paper, possible reasons for this discrepancy are discussed and a method is developed to simplify

Efficient estimation of an additive quantile regression model

NARCIS (Netherlands)

Cheng, Y.; de Gooijer, J.G.; Zerom, D.

2009-01-01

In this paper two kernel-based nonparametric estimators are proposed for estimating the components of an additive quantile regression model. The first estimator is a computationally convenient approach which can be viewed as a viable alternative to the method of De Gooijer and Zerom (2003). By

Efficient estimation of an additive quantile regression model

NARCIS (Netherlands)

Cheng, Y.; de Gooijer, J.G.; Zerom, D.

2010-01-01

In this paper two kernel-based nonparametric estimators are proposed for estimating the components of an additive quantile regression model. The first estimator is a computationally convenient approach which can be viewed as a viable alternative to the method of De Gooijer and Zerom (2003). By

Selecting parts for additive manufacturing in service logistics

NARCIS (Netherlands)

Knofius, Nils; van der Heijden, Matthijs C.; Zijm, Willem H.M.

2016-01-01

Purpose – For more than ten years, the value of additive manufacturing (AM) for after-sales service logistics has been propagated. Today, however, only few applications are observed in practice. In this paper, possible reasons for this discrepancy are discussed and a method is developed to simplify

Evaluation of methods used to determine realized energy savings

International Nuclear Information System (INIS)

Boonekamp, Piet G.M.

2006-01-01

Most methods to determine realized total energy savings at national or sectoral level make choices, or neglect problems, which hamper the calculation of sound and useful energy-saving figures. Issues are the choice of the right aggregation level, the appropriate variables to construct a reference energy consumption trend, the energy quantities to be applied and interaction between various effects. Uncertainty margins for results lack in most presentations as well. This paper presents six methods, illustrates the adverse effects of certain choices and problems, and investigates how these methods deal with them. The methods are scored with respect to the issues mentioned above. Finally, a number of improvements are suggested, among which the use of final energy demand expressed in primary energy units, and bottom-up analyses at the level of real saving options. The last option is the more important, as it could provide top-down evaluation results (total savings from decomposition) as well as bottom-up policy monitoring results, both being crucial to new European energy-saving policy

Monitoring Method of Cutting Force by Using Additional Spindle Sensors

Science.gov (United States)

Sarhan, Ahmed Aly Diaa; Matsubara, Atsushi; Sugihara, Motoyuki; Saraie, Hidenori; Ibaraki, Soichi; Kakino, Yoshiaki

This paper describes a monitoring method of cutting forces for end milling process by using displacement sensors. Four eddy-current displacement sensors are installed on the spindle housing of a machining center so that they can detect the radial motion of the rotating spindle. Thermocouples are also attached to the spindle structure in order to examine the thermal effect in the displacement sensing. The change in the spindle stiffness due to the spindle temperature and the speed is investigated as well. Finally, the estimation performance of cutting forces using the spindle displacement sensors is experimentally investigated by machining tests on carbon steel in end milling operations under different cutting conditions. It is found that the monitoring errors are attributable to the thermal displacement of the spindle, the time lag of the sensing system, and the modeling error of the spindle stiffness. It is also shown that the root mean square errors between estimated and measured amplitudes of cutting forces are reduced to be less than 20N with proper selection of the linear stiffness.

Application of statistical method for FBR plant transient computation

International Nuclear Information System (INIS)

Kikuchi, Norihiro; Mochizuki, Hiroyasu

2014-01-01

Highlights: • A statistical method with a large trial number up to 10,000 is applied to the plant system analysis. • A turbine trip test conducted at the “Monju” reactor is selected as a plant transient. • A reduction method of trial numbers is discussed. • The result with reduced trial number can express the base regions of the computed distribution. -- Abstract: It is obvious that design tolerances, errors included in operation, and statistical errors in empirical correlations effect on the transient behavior. The purpose of the present study is to apply above mentioned statistical errors to a plant system computation in order to evaluate the statistical distribution contained in the transient evolution. A selected computation case is the turbine trip test conducted at 40% electric power of the prototype fast reactor “Monju”. All of the heat transport systems of “Monju” are modeled with the NETFLOW++ system code which has been validated using the plant transient tests of the experimental fast reactor Joyo, and “Monju”. The effects of parameters on upper plenum temperature are confirmed by sensitivity analyses, and dominant parameters are chosen. The statistical errors are applied to each computation deck by using a pseudorandom number and the Monte-Carlo method. The dSFMT (Double precision SIMD-oriented Fast Mersenne Twister) that is developed version of Mersenne Twister (MT), is adopted as the pseudorandom number generator. In the present study, uniform random numbers are generated by dSFMT, and these random numbers are transformed to the normal distribution by the Box–Muller method. Ten thousands of different computations are performed at once. In every computation case, the steady calculation is performed for 12,000 s, and transient calculation is performed for 4000 s. In the purpose of the present statistical computation, it is important that the base regions of distribution functions should be calculated precisely. A large number of

Additive Manufacturing: Multi Material Processing and Part Quality Control

DEFF Research Database (Denmark)

Pedersen, David Bue

This Ph.D dissertation,ffAdditive Manufacturing: Multi Material Processing and Part Quality Controlff, deal with Additive Manufacturing technologies which is a common name for a series of processes that are recognized by being computer controlled, highly automated, and manufacture objects...... by a layered deposition of material. Two areas of particular interest is addressed. They are rooted in two very different areas, yet is intended to fuel the same goal. To help Additive Manufacturing technologies one step closer to becoming the autonomous, digital manufacturing method of tomorrow. Vision...... systems A paradox exist in the field of Additive Manufacturing. The technologies allow for close-to unrestrained and integral geometrical freedom. Almost any geometry can be manufactured fast, e"ciently and cheap. Something that has been missing fundamental capability since the entering of the industrial...

Probiotics And Prebiotics As Feed Additive For Nonruminants

Directory of Open Access Journals (Sweden)

Tuti Haryati

2011-09-01

Full Text Available The ban against using antibiotics has led to increase the use of alternative additive substances as antibiotic. The alternative additives that can be used as antibiotic are probiotic and prebiotic. Both components can be used separately or together as synbiotic. Probiotic and prebiotic can modulate the ecosytem of intestinal microflora that is potential to affect the health and performance of host. Probiotic and prebiotic have been widely used abroad because of their positive effects, but the research and the use of these components in Indonesia are limited, eventhough abundance of raw material that can be used are available. The research dealing with probiotic and prebiotic as additive is necessary to be improved to obtain the efficient and practical production method, which can be implemented to give an economic impact on livestock industry.

Estimation of 131J-Jodohippurateclearance by a simplified method using a single plasma sample

International Nuclear Information System (INIS)

Botsch, H.; Golde, G.; Kampf, D.

1980-01-01

Theoretical volumes calculated from the reciprocal of the plasma concentration of 131 J-Jodohippurate were compared in 95 patients with clearance values calculated by the 2-compartment-method and in 18 patients with conventional PAH-clearance. For estimating Hippurate-clearance from a single blood sampling the most favorable time is 45 min. after injection (r = 0.96; clearance 400/ml/min.: r = 0.98). Clearance values may be derived from the formula: C = 0.4 + 7.26 V - 0.021 x V 2 (V = injected activity/activity per l plasma taken 45 min. after injection). The simplicity, precision and reproducibility of the above mentioned clearance-method is emphasized. (orig.) [de

Study of Supported Nickel Catalysts Prepared by Aqueous Hydrazine Method. Hydrogenating Properties and Hydrogen Storage: Support Effect. Silver Additive Effect

International Nuclear Information System (INIS)

Wojcieszak, R.

2006-06-01

We have studied Ni or NiAg nano-particles obtained by the reduction of nickel salts (acetate or nitrate) by hydrazine and deposited by simple or EDTA-double impregnation on various supports (γ-Al 2 O 3 , amorphous or crystallized SiO 2 , Nb 2 O 5 , CeO 2 and carbon). Prepared catalysts were characterized by different methods (XRD, XPS, low temperature adsorption and desorption of N 2 , FTIR and FTIR-Pyridine, TEM, STEM, EDS, H 2 -TPR, H 2 -adsorption, H 2 -TPD, isopropanol decomposition) and tested in the gas phase hydrogenation of benzene or as carbon materials in the hydrogen storage at room temperature and high pressure. The catalysts prepared exhibited better dispersion and activity than classical catalysts. TOF's of NiAg/SiO 2 or Ni/carbon catalysts were similar to Pt catalysts in benzene hydrogenation. Differences in support acidity or preparation method and presence of Ag as metal additive play a crucial role in the chemical reduction of Ni by hydrazine and in the final properties of the materials. Ni/carbon catalysts could store significant amounts of hydrogen at room temperature and high pressure (0.53%/30 bars), probably through the hydrogen spillover effect. (author)

Emerging technologies in arthroplasty: additive manufacturing.

Science.gov (United States)

Banerjee, Samik; Kulesha, Gene; Kester, Mark; Mont, Michael A

2014-06-01

Additive manufacturing is an industrial technology whereby three-dimensional visual computer models are fabricated into physical components by selectively curing, depositing, or consolidating various materials in consecutive layers. Although initially developed for production of simulated models, the technology has undergone vast improvements and is currently increasingly being used for the production of end-use components in various aerospace, automotive, and biomedical specialties. The ability of this technology to be used for the manufacture of solid-mesh-foam monolithic and coated components of complex geometries previously considered unmanufacturable has attracted the attention of implant manufacturers, bioengineers, and orthopedic surgeons. Currently, there is a paucity of reports describing this fabrication method in the orthopedic literature. Therefore, we aimed to briefly describe this technology, some of the applications in other orthopedic subspecialties, its present use in hip and knee arthroplasty, and concerns with the present form of the technology. As there are few reports of clinical trials presently available, the true benefits of this technology can only be realized when studies evaluating the clinical and radiographic outcomes of cementless implants manufactured with additive manufacturing report durable fixation, less stress shielding, and better implant survivorship. Nevertheless, the authors believe that this technology holds great promise and may potentially change the conventional methods of casting, machining, and tooling for implant manufacturing in the future. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

The effect of empirical potential functions on modeling of amorphous carbon using molecular dynamics method

International Nuclear Information System (INIS)

Li, Longqiu; Xu, Ming; Song, Wenping; Ovcharenko, Andrey; Zhang, Guangyu; Jia, Ding

2013-01-01

Empirical potentials have a strong effect on the hybridization and structure of amorphous carbon and are of great importance in molecular dynamics (MD) simulations. In this work, amorphous carbon at densities ranging from 2.0 to 3.2 g/cm 3 was modeled by a liquid quenching method using Tersoff, 2nd REBO, and ReaxFF empirical potentials. The hybridization, structure and radial distribution function G(r) of carbon atoms were analyzed as a function of the three potentials mentioned above. The ReaxFF potential is capable to model the change of the structure of amorphous carbon and MD results are in a good agreement with experimental results and density function theory (DFT) at low density of 2.6 g/cm 3 and below. The 2nd REBO potential can be used when amorphous carbon has a very low density of 2.4 g/cm 3 and below. Considering the computational efficiency, the Tersoff potential is recommended to model amorphous carbon at a high density of 2.6 g/cm 3 and above. In addition, the influence of the quenching time on the hybridization content obtained with the three potentials is discussed.

Chloride ion addition for controlling shapes and properties of silver nanorods capped by polyvinyl alcohol synthesized using polyol method

Energy Technology Data Exchange (ETDEWEB)

Junaidi, E-mail: junaidi.1982@fmipa.unila.ac.id [Department of Physics, Universitas Gadjah Mada, Yogyakarta, 55281 (Indonesia); Department of Physics, Lampung University, Bandar Lampung (Indonesia); Yunus, Muhammad, E-mail: muhammad.yunus@mail.ugm.ac.id [Department of Physics, Universitas Gadjah Mada, Yogyakarta, 55281 (Indonesia); Triyana, Kuwat, E-mail: triyana@ugm.ac.id; Harsojo,, E-mail: harsojougm@ugm.ac.id; Suharyadi, Edi, E-mail: esuharyadi@ugm.ac.id [Department of Physics, Universitas Gadjah Mada, Yogyakarta, 55281 (Indonesia); Nanomaterials Research Group, Universitas Gadjah Mada, Yogyakarta, 55281 (Indonesia)

2016-04-19

We report our investigation on the effect of chloride ions on controlling the shapes and properties of silver nanorods (AgNRs) synthesized using a polyol method. In this study, we used polyvinyl alcohol (PVA) as a capping agent and sodium chloride (NaCl) as a salt precursor and performed at the oil bath temperature of 140°C. The chloride ions originating from the NaCl serve to control the growth of the silver nanorods. Furthermore, the synthesized silver nanorods were characterized using SEM and XRD. The results showed that besides being able to control the growth of AgCl atoms, the chloride ions were also able to control the growth of multi-twinned-particles into the single crystalline of silver nanorods by micrometer-length. At an appropriate concentration of NaCl, the diameter of silver nanorods decreased significantly compared to that of without chloride ion addition. This technique may be useful since a particular diameter of silver nanorods affects a particular application in the future.

Chloride ion addition for controlling shapes and properties of silver nanorods capped by polyvinyl alcohol synthesized by polyol method

International Nuclear Information System (INIS)

Junaidi; Triyana, Kuwat; Harsojo,; Suharyadi, Edi

2016-01-01

We report our investigation on the effect of chloride ions oncontrolling the shapes and properties of silver nanorods(AgNRs) synthesized using a polyol method. In this study, we used polyvinyl alcohol (PVA) as a capping agent and sodium chloride (NaCl) as asalt precursor and performed at the oilbath temperature of 140 °C. The chloride ions originating from the NaCl serve to control the growth of the silver nanorods. Furthermore, the synthesized silver nanorodswere characterized using UV-VIS, XRD, SEM and TEM. The results showed that besides being able to control the growth of AgCl atoms, the chloride ions were also able to control the growth of multi-twinned-particles into the single crystalline silver nanorods by micrometer-length. At an appropriate concentration of NaCl, the diameter of silver nanorodsdecreased significantly compared to that of without chloride ion addition. This technique may be useful since a particular diameter of silver nanorods affects a particular application in the future.

Chloride ion addition for controlling shapes and properties of silver nanorods capped by polyvinyl alcohol synthesized using polyol method

International Nuclear Information System (INIS)

Junaidi; Yunus, Muhammad; Triyana, Kuwat; Harsojo,; Suharyadi, Edi

2016-01-01

We report our investigation on the effect of chloride ions on controlling the shapes and properties of silver nanorods (AgNRs) synthesized using a polyol method. In this study, we used polyvinyl alcohol (PVA) as a capping agent and sodium chloride (NaCl) as a salt precursor and performed at the oil bath temperature of 140°C. The chloride ions originating from the NaCl serve to control the growth of the silver nanorods. Furthermore, the synthesized silver nanorods were characterized using SEM and XRD. The results showed that besides being able to control the growth of AgCl atoms, the chloride ions were also able to control the growth of multi-twinned-particles into the single crystalline of silver nanorods by micrometer-length. At an appropriate concentration of NaCl, the diameter of silver nanorods decreased significantly compared to that of without chloride ion addition. This technique may be useful since a particular diameter of silver nanorods affects a particular application in the future.

Effect of additive gases and injection methods on chemical dry etching of silicon nitride, silicon oxynitride, and silicon oxide layers in F2 remote plasmas

International Nuclear Information System (INIS)

Yun, Y. B.; Park, S. M.; Kim, D. J.; Lee, N.-E.; Kim, K. S.; Bae, G. H.

2007-01-01

The authors investigated the effects of various additive gases and different injection methods on the chemical dry etching of silicon nitride, silicon oxynitride, and silicon oxide layers in F 2 remote plasmas. N 2 and N 2 +O 2 gases in the F 2 /Ar/N 2 and F 2 /Ar/N 2 /O 2 remote plasmas effectively increased the etch rate of the layers. The addition of direct-injected NO gas increased the etch rates most significantly. NO radicals generated by the addition of N 2 and N 2 +O 2 or direct-injected NO molecules contributed to the effective removal of nitrogen and oxygen in the silicon nitride and oxide layers, by forming N 2 O and NO 2 by-products, respectively, and thereby enhancing SiF 4 formation. As a result of the effective removal of the oxygen, nitrogen, and silicon atoms in the layers, the chemical dry etch rates were enhanced significantly. The process regime for the etch rate enhancement of the layers was extended at elevated temperature

Experimental study of the burned of nuclear fuel by the gamma spectroscopy method

International Nuclear Information System (INIS)

Amador V, P.

2009-01-01

Accurate information on nuclear fuel burnup is of vital importance in reactor operation, fuel management and fuel-characteristics studies. Conventionally fuel management of the TRIGA III Reactor from the National Institute of Nuclear Research (ININ) is done through the thermal balance method (management) of the power generated during reactor operation, since it is known that with 1.24 grams of 235 U is possible to generate a power or 1 MW per day during the reactor operation. On the other hand, it is possible to calculate the operation time in days during a power of 1 MW with the help of the data registered in logs. With the information just mentioned one can calculate the quantity of 235 U consumed in the fuel during a complete period of irradiation. In order to compare and prove that the burnup values, calculated through the thermal balance method, are correct, the ININ implemented, for the first time, the gamma-ray spectroscopy method as an experimental technique to calculate the burnup of several fuel elements. Gamma-ray spectroscopy is a nondestructive method, so that the integrity of the fuel element is not affected which is of great importance. Since there is a direct relation between the activity of 137 Cs contained in the fuel elements and a series of constants which are unique for the radioisotope and for the high resolution system, the problem just simplifies in measuring the 137 Cs activities. Furthermore the 137 Cs concentration equation was developed theoretically and I wrote a computer program (AMAVAL) in Fortran. The task of this program is to calculate the concentrations and the activity through the use of the equation just mentioned and the history of each fuel element. The purpose of this is to compare and validate the experimental activities with the theoretical ones for each fuel element. (Author)

Sol–gel zirconia nanopowders with α-cyclodextrin as organic additive

International Nuclear Information System (INIS)

Răileanu, M.; Todan, L.; Crişan, D.; Drăgan, N.; Crişan, M.; Stan, C.; Andronescu, C.; Voicescu, M.; Vasile, B.S.; Ianculescu, A.

2012-01-01

Highlights: ► The sol–gel synthesis of a zirconia powder has been performed, in the presence of α-cyclodextrin as organic additive. ► A crystalline powder consisting from a mixture of monoclinic and tetragonal zirconia phases has resulted after the thermal treatment. ► The organic additive acted the role of metal oxides used as doppants for zirconia powders, avoiding phase transformations. ► The α-cyclodextrin made particles to assume spherical shape and reach fairly uniform size and prevented their agglomeration. ► The organic additive led to a certain porous morphology of the zirconia particles that is pores embedded within grains. - Abstract: Nanomaterials present unique structural and physicochemical properties due to their ultra fine size of particles that make them very useful in many domains. The most spectacular applications of nanosized zirconia include ceramics, piezoelectrics, refractories, pigments, solid electrolytes, oxygen sensors, catalysts, ultrafiltration membranes, and chromatography packing materials. Nanostructured zirconia powders can be prepared using various methods, such as sol–gel process, coprecipitation, hydrothermal synthesis, and reverse micelle method. The aim of the present work was to prepare zirconia nanopowders through the sol–gel method, using α-cyclodextrin as organic additive and to establish its influence on the structural and textural properties of the obtained product. A white, amorphous ZrO 2 powder containing α-cyclodextrin was prepared, which became a crystalline, stable one, after removing the organic matter by thermal treatment. The resulted nanocrystalline powder contains both monoclinic and tetragonal zirconia phases and is very stable. It presents a relatively reduced tendency of agglomeration of particles and contains closed pores which are embedded in the zirconia matrix. The zirconia powders were characterized using the following methods: thermal analysis, IR spectroscopy, UV–vis spectroscopy

Modified management practices: a review and analysis of methods in Swedish forestry

International Nuclear Information System (INIS)

Hejnebo, A.

1997-01-01

To preserve biodiversity in the forest landscape there must probably be some modifications in the forest management. Some smaller parts of the forest land must get total protection from forest operations, while the major part can be managed the traditional way. In addition to these two ways of managing the forest, there is also the nature conservation-oriented forest management that can be considered as something between the two first mentioned. This managing strategy is adapted to conditions where it is desirable to imitate the natural processes that the forest was exposed to in the natural state. This essay is a review of conservation-oriented forest management and an evaluation of how environment, production and economy are affected

A composite experimental dynamic substructuring method based on partitioned algorithms and localized Lagrange multipliers

Science.gov (United States)

Abbiati, Giuseppe; La Salandra, Vincenzo; Bursi, Oreste S.; Caracoglia, Luca

2018-02-01

Successful online hybrid (numerical/physical) dynamic substructuring simulations have shown their potential in enabling realistic dynamic analysis of almost any type of non-linear structural system (e.g., an as-built/isolated viaduct, a petrochemical piping system subjected to non-stationary seismic loading, etc.). Moreover, owing to faster and more accurate testing equipment, a number of different offline experimental substructuring methods, operating both in time (e.g. the impulse-based substructuring) and frequency domains (i.e. the Lagrange multiplier frequency-based substructuring), have been employed in mechanical engineering to examine dynamic substructure coupling. Numerous studies have dealt with the above-mentioned methods and with consequent uncertainty propagation issues, either associated with experimental errors or modelling assumptions. Nonetheless, a limited number of publications have systematically cross-examined the performance of the various Experimental Dynamic Substructuring (EDS) methods and the possibility of their exploitation in a complementary way to expedite a hybrid experiment/numerical simulation. From this perspective, this paper performs a comparative uncertainty propagation analysis of three EDS algorithms for coupling physical and numerical subdomains with a dual assembly approach based on localized Lagrange multipliers. The main results and comparisons are based on a series of Monte Carlo simulations carried out on a five-DoF linear/non-linear chain-like systems that include typical aleatoric uncertainties emerging from measurement errors and excitation loads. In addition, we propose a new Composite-EDS (C-EDS) method to fuse both online and offline algorithms into a unique simulator. Capitalizing from the results of a more complex case study composed of a coupled isolated tank-piping system, we provide a feasible way to employ the C-EDS method when nonlinearities and multi-point constraints are present in the emulated system.

[Application of ordinary Kriging method in entomologic ecology].

Science.gov (United States)

Zhang, Runjie; Zhou, Qiang; Chen, Cuixian; Wang, Shousong

2003-01-01

Geostatistics is a statistic method based on regional variables and using the tool of variogram to analyze the spatial structure and the patterns of organism. In simulating the variogram within a great range, though optimal simulation cannot be obtained, the simulation method of a dialogue between human and computer can be used to optimize the parameters of the spherical models. In this paper, the method mentioned above and the weighted polynomial regression were utilized to simulate the one-step spherical model, the two-step spherical model and linear function model, and the available nearby samples were used to draw on the ordinary Kriging procedure, which provided a best linear unbiased estimate of the constraint of the unbiased estimation. The sum of square deviation between the estimating and measuring values of varying theory models were figured out, and the relative graphs were shown. It was showed that the simulation based on the two-step spherical model was the best simulation, and the one-step spherical model was better than the linear function model.

Additive manufacturing.

Science.gov (United States)

Mumith, A; Thomas, M; Shah, Z; Coathup, M; Blunn, G

2018-04-01

Increasing innovation in rapid prototyping (RP) and additive manufacturing (AM), also known as 3D printing, is bringing about major changes in translational surgical research. This review describes the current position in the use of additive manufacturing in orthopaedic surgery. Cite this article: Bone Joint J 2018;100-B:455-60.

Heavy water production by the method of ammonia rectification with heat pump. Experience of starting of industrial installation

International Nuclear Information System (INIS)

Rozen, A.M.

1995-01-01

Basic results of the start-up in 1955 of a facility for heavy water production by ammonia refining are presented to substantiate its economic profitability. The description of the facility is given, data on the materials corrosion resistance, efficiency of the operation of the trays and pumps are provided. It is shown that the mentioned method of heavy water production in terms of economic indices is similar to highly efficient methods, namely: refining of liquid hydrogen and water-hydrogen sulfide two-temperature isotopic exchange. 14 refs., 14 figs., 2 tabs

[The current status and outlook for molecular genetic methods in solving the tasks of medical microbiology].

Science.gov (United States)

Gintsburg, A L; Zigangirova, N A; Romanova, Iu M

1999-01-01

The article deals with modern methods, viz. PCR, molecular display and genotherapy, which permit the new approach to the solution of problems connected with the identification of infective agents, the study of the mechanisms of the pathogenesis of infectious diseases and their treatment. In this article concrete examples, clearly demonstrating how each of the above-mentioned technologies makes it possible to broaden the circle of problems solved in infectious pathology of man, are presented.

Use of Vitelline Protein B as a Microencapsulating Additive

Science.gov (United States)

Ficht, Allison R. (Inventor); Carson, Ken (Inventor); Sheffield, Cynthia (Inventor); Waite, John Herbert (Inventor)

2017-01-01

The present invention includes compositions and methods for the use of an encapsulation additive having between about 0.1 to about 30 percent isolated and purified vitelline protein B to provide for mixed and extended release formulations.

A STUDY ON RANKING METHOD IN RETRIEVING WEB PAGES BASED ON CONTENT AND LINK ANALYSIS: COMBINATION OF FOURIER DOMAIN SCORING AND PAGERANK SCORING

Directory of Open Access Journals (Sweden)

Diana Purwitasari

2008-01-01

Full Text Available Ranking module is an important component of search process which sorts through relevant pages. Since collection of Web pages has additional information inherent in the hyperlink structure of the Web, it can be represented as link score and then combined with the usual information retrieval techniques of content score. In this paper we report our studies about ranking score of Web pages combined from link analysis, PageRank Scoring, and content analysis, Fourier Domain Scoring. Our experiments use collection of Web pages relate to Statistic subject from Wikipedia with objectives to check correctness and performance evaluation of combination ranking method. Evaluation of PageRank Scoring show that the highest score does not always relate to Statistic. Since the links within Wikipedia articles exists so that users are always one click away from more information on any point that has a link attached, it it possible that unrelated topics to Statistic are most likely frequently mentioned in the collection. While the combination method show link score which is given proportional weight to content score of Web pages does effect the retrieval results.

Further Insight and Additional Inference Methods for Polynomial Regression Applied to the Analysis of Congruence

Science.gov (United States)

Cohen, Ayala; Nahum-Shani, Inbal; Doveh, Etti

2010-01-01

In their seminal paper, Edwards and Parry (1993) presented the polynomial regression as a better alternative to applying difference score in the study of congruence. Although this method is increasingly applied in congruence research, its complexity relative to other methods for assessing congruence (e.g., difference score methods) was one of the…

A novel baseline-correction method for standard addition based derivative spectra and its application to quantitative analysis of benzo(a)pyrene in vegetable oil samples.

Science.gov (United States)

Li, Na; Li, Xiu-Ying; Zou, Zhe-Xiang; Lin, Li-Rong; Li, Yao-Qun

2011-07-07