Metallographic study of ferrite → sigma transformation using ferromagnetic colloid, microprobe analysis, and color etching

International Nuclear Information System (INIS)

Gray, R.J.; Crouse, R.S.; Sikka, V.K.; King, R.T.

1976-01-01

The mechanical properties of ferrite-containing austenitic stainless steel base metal and weldments are usually adversely affected by prolonged exposure to temperatures in the 482-900 0 C (900-1652 0 F) range. One cause of the property alteration is related to the transformation of relatively ductile delta-ferrite to less ductile sigma-phase. Attempts to identify sigma and delta ferrite phases by color staining techniques alone are well documented; however, the results are often questionable due to the difficulty in maintaining consistent color identifications. This investigation is concerned with the microstructural responses of the ferromagnetic delta-ferrite phase and the paramagnetic sigma-phase to a ferromagnetic iron colloid in a magnetic field. Such positive or negative responses of the two phases to the colloid offer a more definitive identification. With this technique, the identification of small amounts of these phases in the microstructure is limited only by the highest magnification and resolution of the optical microscope. The procedure is substantiated in this metallographic study with microprobe analysis and color metallography. Several examples of the correlative use of these three techniques in identifying varying amounts of delta-ferrite yields sigma transformation are presented

Metallographic and autoradiographic investigation of the structure of centrifugally cast steel

International Nuclear Information System (INIS)

Singh, K.N.; Krishna Rao, P.

1981-01-01

Metallographic and autoradiographic investigations were carried out on the structure of steel tubes cast in a horizontal axis centrifugal casting machine. In chill castings the chill and columnar zones showed significantly lower sulphur contents than the equiaxed zone. Mould rotational speed was found to have an important influence on sulphur segregation. Sulphur-depleted bands, which were often observed in the castings were found to arise due to minor variations in the mould rotational speed. (auth.)

Metallographic Characterization of Wrought Depleted Uranium

Energy Technology Data Exchange (ETDEWEB)

Forsyth, Robert Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hill, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-02-14

Metallographic characterization was performed on wrought depleted uranium (DU) samples taken from the longitudinal and transverse orientations from specific locations on two specimens. Characterization of the samples included general microstructure, inclusion analysis, grain size analysis, and microhardness testing. Comparisons of the characterization results were made to determine any differences based on specimen, sample orientation, or sample location. In addition, the characterization results for the wrought DU samples were also compared with data obtained from the metallographic characterization of cast DU samples previously characterized. No differences were observed in microstructure, inclusion size, morphology, and distribution, or grain size in regard to specimen, location, or orientation for the wrought depleted uranium samples. However, a small difference was observed in average hardness with regard to orientation at the same locations within the same specimen. The longitudinal samples were slightly harder than the transverse samples from the same location of the same specimen. This was true for both wrought DU specimens. Comparing the wrought DU sample data with the previously characterized cast DU sample data, distinct differences in microstructure, inclusion size, morphology and distribution, grain size, and microhardness were observed. As expected, the microstructure of the wrought DU samples consisted of small recrystallized grains which were uniform, randomly oriented, and equiaxed with minimal twinning observed in only a few grains. In contrast, the cast DU microstructure consisted of large irregularly shaped grains with extensive twinning observed in most grains. Inclusions in the wrought DU samples were elongated, broken and cracked and light and dark phases were observed in some inclusions. The mean inclusion area percentage for the wrought DU samples ranged from 0.08% to 0.34% and the average density from all wrought DU samples was 1.62E+04/cm

Fracture toughness of fabrication welds investigated by metallographic methods

International Nuclear Information System (INIS)

Canonico, D.A.; Crouse, R.S.

1978-01-01

The intermediate scale test vessels (ITV) were fabricated to provide test specimens that have sufficient wall thickness and simulate light water reactor pressure vessels. They were fabricated from grades of steel that are similar to those used for nuclear pressure vessels, having a wall thickness of 150mm and the same welded construction. They are, however, considerably smaller in height and diameter than actual vessels. To date, ten vessels have been fabricated and eight have been tested. In preparation for testing the eighth vessel (ITV-8), an extensive investigation was conducted of the toughness properties of the fabrication weld. It was thoroughly characterized and the fracture specimens used in this metallographic investigation were taken from that weld metal

Metallographic examination of damaged N reactor spent nuclear fuel element SFEC5,4378

Energy Technology Data Exchange (ETDEWEB)

Marschman, S.C.; Pyecha, T.D.; Abrefah, J.

1997-08-01

N-Reactor spent nuclear fuel (SNF) is currently residing underwater in the K Basins at the Hanford site, in Richland, Washington. This report presents results of the metallographic examination of specimens cut from an SNF element (Mark IV-E) with breached cladding. The element had resided in the K-West (KW) Storage Basin for at least 10 years after it was discharged from the N-Reactor. The storage containers in the KW Basin were nominally closed, isolating the SNF elements from the open pool environment. Seven specimens from this Mark IV-E outer fuel element were examined using an optical metallograph. Included were two specimens that had been subjected to a conditioning process recommended by the Independent Technical Assessment Team, two specimens that had been subjected to a conditioning process recommended in the Integrated Process Strategy Report, and three that were in the as-received, as-cut condition. One of the as-received specimens had been cut from the damaged (or breached) end of the element. All other specimens were cut from the undamaged mid-region of the fuel element. The specimens were visually examined to (1) identify uranium hydride inclusions present in the uranium metal fuel, (2) measure the thickness of the oxide layer formed on the uranium edges and assess the apparent integrity and adhesion of the oxide layer, and (3) look for features in the microstructure that might provide an insight into the various corrosion processes that occurred during underwater storage in the KW Basin. These features included, but were not limited to, the integrity of the cladding and the fuel-to-cladding bond, obvious anomalies in the microstructure, excessive pitting or friability of the fuel matrix, and obvious anomalies in the distribution of uranium hydride or uranium carbide inclusions. Also, the observed metallographic features of the conditioned specimens were compared with those of the as-received (unconditioned) specimens. 11 refs., 93 figs., 2 tabs.

Results of metallographical diagnostic examination of Navy half-watt thermoelectric converters degraded by accelerated tests

International Nuclear Information System (INIS)

Rosell, F.E. Jr.; Rouklove, P.G.

1977-01-01

To verify the 15-year reliability of the Navy half-watt radioisotope thermoelectric generator (RTG), bismuth--telluride thermoelectric converters were submitted to testing at high temperatures which accelerated the degradation and caused failure of the converters. Metallographic diagnostic examination of failed units verified failure mechanisms. Results of diagnostic examinations are presented

Metallographic study of reconstitution welding in inserts of 1 cm3

International Nuclear Information System (INIS)

Romero C, J.; Garcia R, R.; Fernandez T, F.; Perez R, N.; Rocamontes A, M.

2007-01-01

In this article, the welding metallographic study carried out in Charpy test tubes reconstituted with notch in 'V', used in the surveillance programs of the vessel in nucleo electric plants is described. Inserts of 1 cm 3 are used, where the inserts are usually rectangular of minimum 18 millimeters of length. The importance of using inserts of 1 cm 3 is that the mechanical properties can be measured in another direction of the vessel steel, when changing the direction or sense of the notch in 'V' or the face where this notch is made in the insert. (Author)

Metallographic post-test investigations for the scaled core-meltdown-experiments FOREVER-1 and -2

International Nuclear Information System (INIS)

Mueller, G.; Boehmert, J.

2000-08-01

FOREVER (Failure Of Reactor Vessel Rentention) experiments have been carried out in order to simulate the behaviour the lower head of a reactor pressure vessel under the conditions of a depressurized core melt down scenario. In particular the creep behaviour and the vessel failure mode have been investigated. Metallographic post test investigations have complemented the experimental programme. Samples of different height positions of the vessel of the FOREVER-C1 and -C2 experiments were metallographically examined and characteristic microstructural appearances were identified. Additionally samples with ineffected microstructure were annealed at different temperatures and cooled by different rates and afterwards investigated. In this way the microstructural effects of the temperature regime, the thermomechanical loads and the environmental attack could be characterized. Remarkable effects were characteristic for the FOREVER-C2 experiment where the highest-loaded region below the welding joint reached temperatures of approx. 1100 C and a strong creep damage occurred. In the FOREVER-C1 experiment creep damage could not be observed and the maximum temperature did not exceed 900 C. Environmental attack generated decarburization and oxidation but the effect was restricted to a narrow surface layer. There was almost no chemical interaction between the oxidic melt and the vessel material. (orig.)

Nondestructive metallographic control for the determination of the degree of sensitivity to intragranular corrosion of austenitic stainless steels; Control metalografico no destructivo para determinar el grado de sensibilidad a la corrosion intergranular de aceros inoxidables austeniticos

Energy Technology Data Exchange (ETDEWEB)

Diaz S, A; Juarez G, F [Instituto Nacional de Investigaciones Nucleares, Mexico City (Mexico)

1994-12-31

The relationship between: microstructure-heat treatment, microstructure-mechanical properties, microstructure-corrosion resistance make that the study of the microstructure of metals and alloys be a powerful tool either in technical-scientific research as in the control of materials. The destructive nature of metallographic analysis create a serious limitation in the case of control methods for failures in the service. The `Tampon` Method make possible the polishing `In situ` of the majority of metals and alloys of industrial use, and the method of nitrocellulose replica allows the obtention of an accurate copy of the metallographic structure which can be observed by transparency or reflection. The purpose of this work is to show in a general way, the fundamental principles of the technique for the obtention of replicas, as well as the countless benefits of its utilization in the national industry. (Author).

Descriptive, metallographic and chemical study of cooper-alloy points found at the grave of one member of the Sican elite, Lambayeque - Peru, using optical microscopy techniques and neutron activation analysis

International Nuclear Information System (INIS)

Vetter, L.; Carcedo, P.; Cutipa, S.; Montoya, E.

1997-01-01

This paper offers a description as well as physical and morphological analyses of 489 points found inside the grave of one of the elite members of Sican (900 - 1110 dC). A metallographic study of one of the points is also carried out, plus the multielemental-quantitative chemical analysis of twelve items from the same grave. In addition, four points of the same culture from the Museo Nacional de Arqueologia, Antropologia e Historia of Peru are also analyzed

Use your eyes - metallographic versus superficial traces of the crafting of Bronze Age ornaments

DEFF Research Database (Denmark)

Nørgaard, Heide Wrobel

and superficial archaeological examinations can be used to understand prehistoric craft. Furthermore, it will show that with an intensive knowledge about previous scientific investigations the superficial traces preserved can reveal a great amount of information and could talk for themselves. Taking as an example...... the early and middle Bronze Age bronze ornaments from North Germany, superficial traces of the metal crafting process, visible with the naked eye, will be compared with metallographic images. The aim of this presentation is to give an overview over the crafting traces everybody could see (with a bit...

Development of Metallographic Etchants for the Microstructure Evolution of A6082-T6 BFSW Welds

Directory of Open Access Journals (Sweden)

Abbas Tamadon

2017-10-01

Full Text Available BACKGROUND—The solid-phase joining of A6082-T6 plates by bobbin friction stir welding (BFSW is problematic. Better methods are needed to evaluate the microstructural evolution of the weld. However, conventional Al reagents (e.g., Keller’s and Kroll’s do not elucidate the microstructure satisfactorily, specifically regarding grain size and morphology within the weld region. APPROACH—We developed innovative etchants for metallographic observations for optical microscopy. RESULTS—The macrostructure and microstructure of A6082-T6 BFSW welds were clearly demonstrated by optical microscopy analysis. The microetching results demonstrated different microstructures of the Stir Zone (S.Z distinct from the Base Metal (B.M and Heat Affected Zone (HAZ & Thermo-mechanical Affected Zone (TMAZ. The micrographs showed a significant decrease in grain size from 100 μm in B.M to ultrafine 4–10 μm grains for the S.Z. Also, the grain morphology changed from directional columnar in the B.M to equiaxed in the S.Z. Furthermore, thermomechanical recrystallization was observed by the morphological flow of the grain distortion in HAZ and TMAZ. The etchants also clearly show the polycrystalline structure, microflow patterns, and the incoherent interface around inclusion defects. ORIGINALITY—Chemical compositions are identified for a suite of etchant reagents for metallographic examination of the friction-stir welded A6082-T6 alloy. The reagents have made it possible to reveal microstructures not previously evident with optical microscopy.

Equipment of the metallographic cell n. 10 in the irradiated fuel element laboratories (L.E.C.L)

International Nuclear Information System (INIS)

Roussel, E.; Vignesoult, N.

1963-01-01

A conventional metallographic apparatus has been adapted for work in a protected cell. The small size of the apparatus and the placing of this apparatus simply on a working bench which can easily be dismantled make it possible on the one hand to repair the apparatus easily in the event of a breakdown, and on the other hand to decontaminate it fairly easily without the presence of a technician in the cell. (authors) [fr

Metallographic characterisation of Al6061-T6 aluminium plates subjected to ballistic impact

International Nuclear Information System (INIS)

Manes, A.; Pagani, M.; Saponara, M.; Mombelli, D.; Mapelli, C.; Giglio, M.

2014-01-01

Al6061-T6 aluminium single layer plates, of different thickness, impacted by two different 7.62 mm Armour Piercing projectiles are studied from a metallographic point of view. The material behaviour after ballistic impact is investigated by optical and scanning electron microscopy as well as by micro-hardness tests. The study allows one to highlight the physical phenomena that happen during the impact: the formation of adiabatic shear bands (ASB), the evolution of softening and hardening phenomena, the creation of petalling, plugging and the formation of a melted film between the target and the penetrator as well as the localised failure mechanism. The thermo-mechanical effects on the target and the penetrator material have been examined in order to investigate in the physical phenomena ruling the ballistic damage; the differences between the two types of impactors are also highlighted. Among interesting findings, it has been noticed that a complete penetration is less detrimental and tungsten core projectile seems more damaging for the structural integrity of Al6061-T6 plates. A complete penetration allows the material to better dissipate the plastic deformation energy induced by bullet whereas the arrest increases localised material softening effect resulting in the formation of ASB. Although the creation of numerical models is not the aim of the present paper, the findings could be useful for the building of a modelling approach capable of replicating all the involved phenomena in details

Metallographic characterisation of Al6061-T6 aluminium plates subjected to ballistic impact

Energy Technology Data Exchange (ETDEWEB)

Manes, A., E-mail: andrea.manes@polimi.it; Pagani, M.; Saponara, M.; Mombelli, D.; Mapelli, C.; Giglio, M.

2014-07-01

Al6061-T6 aluminium single layer plates, of different thickness, impacted by two different 7.62 mm Armour Piercing projectiles are studied from a metallographic point of view. The material behaviour after ballistic impact is investigated by optical and scanning electron microscopy as well as by micro-hardness tests. The study allows one to highlight the physical phenomena that happen during the impact: the formation of adiabatic shear bands (ASB), the evolution of softening and hardening phenomena, the creation of petalling, plugging and the formation of a melted film between the target and the penetrator as well as the localised failure mechanism. The thermo-mechanical effects on the target and the penetrator material have been examined in order to investigate in the physical phenomena ruling the ballistic damage; the differences between the two types of impactors are also highlighted. Among interesting findings, it has been noticed that a complete penetration is less detrimental and tungsten core projectile seems more damaging for the structural integrity of Al6061-T6 plates. A complete penetration allows the material to better dissipate the plastic deformation energy induced by bullet whereas the arrest increases localised material softening effect resulting in the formation of ASB. Although the creation of numerical models is not the aim of the present paper, the findings could be useful for the building of a modelling approach capable of replicating all the involved phenomena in details.

New Analysis Method Application in Metallographic Images through the Construction of Mosaics Via Speeded Up Robust Features and Scale Invariant Feature Transform

Directory of Open Access Journals (Sweden)

Pedro Pedrosa Rebouças Filho

2015-06-01

Full Text Available In many applications in metallography and analysis, many regions need to be considered and not only the current region. In cases where there are analyses with multiple images, the specialist should also evaluate neighboring areas. For example, in metallurgy, welding technology is derived from conventional testing and metallographic analysis. In welding, these tests allow us to know the features of the metal, especially in the Heat-Affected Zone (HAZ; the region most likely for natural metallurgical problems to occur in welding. The expanse of the Heat-Affected Zone exceeds the size of the area observed through a microscope and typically requires multiple images to be mounted on a larger picture surface to allow for the study of the entire heat affected zone. This image stitching process is performed manually and is subject to all the inherent flaws of the human being due to results of fatigue and distraction. The analyzing of grain growth is also necessary in the examination of multiple regions, although not necessarily neighboring regions, but this analysis would be a useful tool to aid a specialist. In areas such as microscopic metallography, which study metallurgical products with the aid of a microscope, the assembly of mosaics is done manually, which consumes a lot of time and is also subject to failures due to human limitations. The mosaic technique is used in the construct of environment or scenes with corresponding characteristics between themselves. Through several small images, and with corresponding characteristics between themselves, a new model is generated in a larger size. This article proposes the use of Digital Image Processing for the automatization of the construction of these mosaics in metallographic images. The use of this proposed method is meant to significantly reduce the time required to build the mosaic and reduce the possibility of failures in assembling the final image; therefore increasing efficiency in obtaining

Evaluation of microstructure of irradiated fuel channel components of PHWR

International Nuclear Information System (INIS)

Ramadasan, E.

2005-01-01

Performance evaluation and failure analysis of irradiated reactor structural components such as those in-core and PHT circuit components necessitate metallographic evaluation using special metallographic specimen preparation techniques due to the radiation dose and contamination levels involved in handling the specimens. The metallographic specimen preparation techniques that are resorted to involve use of fully automatic and semi automatic machines, shielded metallographic microscope and specialised equipment developed for lead-cell metallography. The techniques used and the results obtained in the metallographic studies on irradiated fuel channel components such as pressure tubes and garter springs of various Indian PHWRs at RAPS, NAPS and MAPS are presented as case studies in the paper. The evaluation of oxidation and hydriding behaviour of zircaloy-2 pressure tubes and garter springs are presented. The paper also gives in detail the microstructural evaluation of hydride blistering seen at the PT-CT contact location of the pressure tubes of RAPS-2. The evaluation revealed that the hydride blisters was small compared to their length, unlike the hydride blisters seen in the CANDU pressure tube G-16 of Pickering-2. This could be attributed to be due to the difference in the annulus conditions between the two types of reactors. The hydride blisters in J-07 pressure tube of RAPS-2 had ductile material adjacent to them. The paper also gives the hydride blistering observation on irradiated Zr-2.5% Nb-0.5% Cu garter springs of RAPS-2. It was seen that there was only negligible hydriding of the garter springs during service through they showed presence of benign hydride blisters in them. The general hydriding observations made on the pressure tubes of Indian PHWRs under different conditions are also presented. (author)

Metallographic examination of TD-nickel base alloys. [thermal and chemical etching technique evaluation

Science.gov (United States)

Kane, R. D.; Petrovic, J. J.; Ebert, L. J.

1975-01-01

Techniques are evaluated for chemical, electrochemical, and thermal etching of thoria dispersed (TD) nickel alloys. An electrochemical etch is described which yielded good results only for large grain sizes of TD-nickel. Two types of thermal etches are assessed for TD-nickel: an oxidation etch and vacuum annealing of a polished specimen to produce an etch. It is shown that the first etch was somewhat dependent on sample orientation with respect to the processing direction, the second technique was not sensitive to specimen orientation or grain size, and neither method appear to alter the innate grain structure when the materials were fully annealed prior to etching. An electrochemical etch is described which was used to observe the microstructures in TD-NiCr, and a thermal-oxidation etch is shown to produce better detail of grain boundaries and to have excellent etching behavior over the entire range of grain sizes of the sample.

Metallographic examination of fire damages in electronic equipment; Metallographische Untersuchung von Brandschaeden in der Elektronik

Energy Technology Data Exchange (ETDEWEB)

Reiter, Katja; Puls, Sebastian [Fraunhofer Institut fuer Siliziumtechnologie, Itzehoe (Germany)

2017-08-01

Defects in electronic components and defects caused by electronic components are a frequent cause of fire damage. 35 % of examined cases of fire damage are found to be caused by electrical equipment or by the handling of electricity. Fire damage caused by electronic elements and in electronic assemblies may have a multitude of causes. Minor damages occurring during the manufacture of electronic components and assemblies can lead to operational disruptions in electronic devices and to life-threatening situations. In order to reconstruct a fire damage, a complex failure analysis and comprehensive knowledge of the principle of operation of the devices is required. Metallographic target preparation serves to detect and describe faults. Some damage patterns taken from practice are presented and analyzed here.

Metallographic analysis of irradiated U3Si2/Al fuel element plate of 2.96 gU/cm3 density

International Nuclear Information System (INIS)

Maman Kartaman Ajiriyanto; Aslina Br Ginting; Junaedi

2018-01-01

Metallographic analysis of U 3 Si 2 /Al fuel element plate has been performed in hot cell. The purpose of metallographic analysis is to study changes in PEB U 3 Si 2 /Al microstructure and AlMg 2 cladding thickness after irradiation in reactor until burn up of 56 %. The fuel element plate of irradiated U 3 Si 2 /Al was cut in top, middle and bottom positions with each size around 5 x 5 x 1.37 mm. Metallographic preparation starts from sample cutting using cutting machine with low speed and sample mounting, grinding and polishing in hot cell 104–105. Sample mounting was done by using resin for more than 10 hours followed by grinding with sand papers up to grit size of 2400 and polishing with diamond paste of size 3 to 1 micron at a rotational speed of 150 rpm for 5 minutes. Microstructure observation was performed with optical microscope in hot cell 107 at 200 times magnification. Microstructure examination reveals U 3 Si 2 particles with inverse forms and sizes, Al matrix and AlMg 2 cladding were spread along the U 3 Si 2 /Al side. Microstructure observation of irradiated U 3 Si 2 /Al has not shown good result because only topography observation of U 3 Si 2 /Al meat, Al matrix and AlMg 2 cladding can be done due to limited capability of the optical microscope in hot cell, where maximum magnification can be attained only at 200 times so that the phenomenon of interaction layer and small gas bubble can not be observed. However, U 3 Si 2 /Al microstructure of 56 % burnup, if compared to the microstructure of U 3 Si 2 /Al fuel element plate of 60 % burnup from previous researcher, shows interaction between U 3 Si 2 meat with Al matrix and the existence of layers with a thickness about 5 up to 20 microns. Meanwhile, the observed thickness of AlMg 2 cladding is greater than 0.25 mm, which indicates that irradiation does not significantly change the thickness of AlMg 2 cladding so that the overall irradiated U 3 Si 2 -Al still has good integrity and stability. (author)

Metallographical procedure for detecting carburized layer in the 12Kh18N10T steel tubes

International Nuclear Information System (INIS)

Najmark, S.I.; Shmalenyuk, R.P.

1977-01-01

The various causes of the tendency to intercrystalline corrosion of stainless steel tubing were studied. 12Kh18N10T steel tube specimens were metallographically investigated to reveal the presence and depth of the carburized layer. Unlubricated specimens and specimens with the graphite-saltpeter lubrication applied on them were austenized in the temperature range from 950 to 1250 deg C and then exposed to a provoking anneal at 650 deg C for 24 h. All the lubricated specimens showed a carbide network along grain boundaries and intercrystalline cracks. The specimens treated without lubrication had no cracks. The method offered can differentiate poor tube cleaning and the undesirable effect of other processing steps on the tubes

The Role of Nano-TiO2 Lubricating Fluid on the Hot Rolled Surface and Metallographic Structure of SS41 Steel

Directory of Open Access Journals (Sweden)

Yanan Meng

2018-02-01

Full Text Available In this paper, nano-TiO2lubricating fluid was chosen as an advanced rolling lubricant to investigate its effect on the hot rolled surface and metallographic structure of SS41 steel strips. The tribological performances of nano-TiO2 lubricating fluid were measured by a four-ball tribotester. The hot rolling experiments under different lubrication conditions were carried out by a four-high rolling mill. The surface morphology, oxide scales and metallographic structure after hot rolling were observed using a confocal laser scanning microscope and scanning electron microscope (SEM, respectively. The composition of surface attachments was analyzed with X-ray photoelectron spectroscopy (XPS. The results indicate that the nano-TiO2 lubricating fluid has a better tribological performance. The surface defects on the hot rolled surface could be decreased. The phase composition of the surface still appears as a mixture of ferrite and pearlite. The surface of steel strips is not micro-alloyed with titanium as predicted. Additionally, the grain size of rolled steel strips which were lubricated with the nano-TiO2lubricating fluid decreased by nearly 50%, compared with traditional lubricating fluid. Furthermore, it was found that the thickness of the oxide layers on the surface reduced, whilst the Rockwell hardness of the oxide layers was enhanced as nano-TiO2 lubricating fluid was applied.

Rare Earth Metal-Based Intermetallics Formation in Al–Cu–Mg and Al–Si–Cu–Mg Alloys: A Metallographic Study

Directory of Open Access Journals (Sweden)

A. M. Samuel

2018-01-01

Full Text Available This study was conducted on Al–Cu–Mg and Al–Si–Cu–Mg alloys containing either 5%La or 5%Ce. Two levels of Ti addition were examined, i.e., 0.05% and 0.15%. Thermal analysis was the only technique used to obtain castings, from which samples were then sectioned for metallographic examination. Based on the results obtained, the following points may be highlighted. Addition of a fairly large amount of RE metals (La or Ce leads to the appearance of several peaks in the solidification curve between the precipitation of the primary α-Al phase and the (Al–Al2Cu eutectic reaction. Although a significant drop in the eutectic temperature is caused by the addition of 5%La or Ce, the corresponding modification of the eutectic Si is marginal. Two main types of intermetallics were documented: a gray phase in the form of sludge with a fixed composition and a white phase in the shape of thin platelets. Due to the high affinity of RE to react with Si, Fe, and Cu, several compositions were obtained explaining the observed multiple peaks in the solidification curve. Judging by the morphology of the gray phase, it is assumed that this phase is precipitated in the liquid state and acts as a nucleation site for the white phase. Lanthanum and Ce can substitute each other.

Self-persuasion as marketing technique: the role of consumers’ involvement

NARCIS (Netherlands)

Bernritter, S.F.; van Ooijen, I.; Müller, B.C.N.

2017-01-01

Purpose: This paper aims to demonstrate that self-persuasion can be used as a marketing technique to increase consumers’ generosity and that the efficacy of this approach is dependent on consumers’ involvement with target behavior. Design/methodology/approach: An experimental field-study was

Self-persuasion as marketing technique: The role of consumers' involvement

NARCIS (Netherlands)

Bernritter, S.F.; Ooijen, I. van; Müller, B.C.N.

2017-01-01

Purpose: This paper seeks to demonstrate that self-persuasion can be used as a marketing technique to increase consumers' generosity and that the efficacy of this approach is dependent on consumers' involvement with the target behavior. Design/Methodology/Approach: An experimental field-study was

Improved Metallography Of Thermal-Barrier Coatings

Science.gov (United States)

Brindley, William J.; Leonhardt, Todd A.

1991-01-01

New technique for preparation of metallographic samples makes interpretation of images of pores and microcracks more reliable. Involves use of vacuum epoxy infiltration and interference-film coating to reduce uncertainty. Developed for inspection of plasma-sprayed ceramic thermal-barrier coatings on metals but applicable to other porous, translucent materials, including many important ceramics.

Metallographic detection of carbides in the steel X 41 CrMoV 51 after different austenizing processes

International Nuclear Information System (INIS)

Fleer, R.; Rickel, J.; Draugelates, U.

1979-01-01

The etchant most suitable for clearly revealing the carbide particles in the developed hardened structure was determined by comparative structural investigations with several etchants in order to be able to undertake the metallographic detection of finely distributed carbides in the structure of the high alloy ultra-high strength steel X 41 CrMoV 51. The characteristic distribution and number of carbides could be revealed as well as the ferrite pearlite matrix. The picric-hydrochloric acid solution which, on a comparative basis, was the most effective, revealed the dependence of the carbide dissolution and structural formation on the temperature. The carbide components of the structure dissolved to an increasing extent at temperatures above 1100 0 C. All carbides up to the large volume mixed carbides appeared to dissolve in the segregation zone after annealing for one hour at 1200 0 C. Considerable grain growth also occurred. (orig./RW) [de

An electrochemical engineering technique to improve the corrosion resistance of some structural materials in lead-alloy coolants

International Nuclear Information System (INIS)

Tacica, M.; Andrei, V.; Rusu, O.; Coaca, E.; Minca, M.; Florea, S.; Oncioiu, G.

2013-01-01

The goal of this paper is to present some conclusions resulted from the literature studies referring to the materials potential to be used in Lead Fast Reactors (LFR), and the results obtained in the surface engineering field which can be used in our institute in order to obtain materials with appropriate properties for their use in LFR. In this context, the paper presents some preliminary results obtained in Surface Analysis Laboratory of INR Pitesti and research works in progress referring to: controlled modification of AISI 316 L surface by electrochemical plasma treatment (carburization, nitrocarburizings); electrodeposition of some protective thin-films based on Ni and Al obtained from ionic liquids; development of some procedures related to the activities involved in the behaviour evaluation, in LFR specific conditions, for material samples subjected to treatments by surface engineering techniques using the LEad COrrosion TEsting LOop (LECOTELO) test bench. The superficial structures obtained have been characterized by metallographic microscopy, X-Ray Photoemission Spectroscopy (XPS), Electrochemical Impedance Spectroscopy (EIS); the electrochemical techniques were used to evaluate the corrosion behaviour. The preliminary results have shown that the used electrochemical surface engineering techniques are appropriate in order to improve the mechanical properties and corrosion behaviour of AISI 316 L steel. (authors)

Metallographic examination of (uth) O2 and UO2 fuel tested in power ramp conditions in triga reactor

International Nuclear Information System (INIS)

Ioncescu, M.; Uta, O.

2015-01-01

The purpose of this paper is to determine the behavior of two fuel experimental elements (EC1 and EC2), by destructive post-irradiation examination. The fuel elements were mounted inside a pattern port, one in extension of the other and irradiated in power ramp conditions in order to check their behavior. Fuel element 1 (EC1) contains (UTh)O''2 pellet, and other one (EC2) UO''2 pellet. The results of destructive post-irradiation examination are evidenced by metallographic and ceramographic analyses. The data obtained from the post-irradiation examinations are used, first to confirm the security, reliability and nuclear fuel performance, and second, for the development of CANDU fuel. The results obtained by destructive examinations regarding the integrity, sheath hydrating and oxidation as well as the structural modifications are typical for fuel elements tested in power ramp conditions. (authors)

Comparison of porosity measurement techniques for porous titanium scaffolds evaluation

International Nuclear Information System (INIS)

Oliveira, M.V.; Ribeiro, A.A.; Moreira, A.C.; Moraes, A.M.C.; Appoloni, C.R.; Pereira, L.C.

2009-01-01

Porous titanium has been used for grafts and implant coatings as it allows the mechanical interlocking of the pores and bone. Evaluation of porous scaffolds for bone regeneration is essential for their manufacture. Porosity, pore size, pore shape and pore homogeneity are parameters that influence strongly the mechanical strength and biological functionality. In this study, porous titanium samples were manufactured by powder metallurgy by using pure titanium powders mixed with a pore former. The quantification of the porosity parameters was assessed in this work by geometric method and gamma-ray transmission, the non-destructive techniques and metallographic images processing, a destructive technique. Qualitative evaluation of pore morphology and surface topography were performed by scanning electron microscopy and optical microscopy. The results obtained and the effectiveness of the techniques used were compared in order to select those most suitable for characterization of porous titanium scaffolds. (author)

Implications for Metallographic Cooling Rates, Derived from Fine-Scale Analytical Traverses Across Kamacite, Taenite, and Tetrataenite in the Butler Iron Meteorite

Science.gov (United States)

Jones, J. H.; Ross, D. K.; Chabot, N. L.; Keller, L. P.

2016-01-01

The "M-shaped" Ni concentrations across Widmanstatten patterns in iron meteorites, mesosiderites, and ordinary chondrites are commonly used to calculate cooling rates. As Ni-poor kamacite exolves from Ni-rich taenite, Ni concentrations build up at the kamacite-taenite interface because of the sluggish diffusivity of Ni. Quantitative knowledge of experimentally-determined Ni diffusivities, coupled with the shape of the M-profile, have been used to allow calculation of cooling rates that pertained at low temperatures, less than or equal to 500 C. However, determining Ni metallographic cooling rates are challenging, due to the sluggish diffusivity of Ni at low temperatures. There are three potential difficulties in using Ni cooling rates at low temperatures: (i) Ni diffusivities are typically extrapolated from higher-temperature measurements; (ii) Phase changes occur at low temperatures that may be difficult to take into account; and (iii) It appears that Ge in kamacite and taenite has continued to equilibrate (or attempted to equilibrate) at temperatures below those that formed the M-shaped Ni profile. Combining Ni measurements with those of other elements has the potential to provide a way to confirm or challenge Ni-determined cooling rates, as well as provide insight into the partitioning behaviors of elements during the cooling of iron meteorites. Despite these benefits, studies that examine elemental profiles of Ni along with other elements in iron meteorites are limited, often due to the low concentration levels of the other elements and associated analytical challenges. The Butler iron meteorite provides a good opportunity to conduct a multi-element analytical study, due to the higher concentration levels of key elements in addition to Fe and Ni. In this work, we perform combined analysis for six elements in the Butler iron to determine the relative behaviors of these elements during the evolution of iron meteorites, with implications for metallographic cooling

Boat sampling technique for assessment of ageing of components

International Nuclear Information System (INIS)

Kumar, Kundan; Shyam, T.V.; Kayal, J.N.; Rupani, B.B.

2006-01-01

Boat sampling technique (BST) is a surface sampling technique, which has been developed for obtaining, in-situ, metal samples from the surface of an operating component without affecting its operating service life. The BST is non-destructive in nature and the sample is obtained without plastic deformation or without thermal degradation of the parent material. The shape and size of the sample depends upon the shape of the cutter and the surface geometry of the parent material. Miniature test specimens are generated from the sample and the specimens are subjected to various tests, viz. Metallurgical Evaluation, Metallographic Evaluation, Micro-hardness Evaluation, sensitisation test, small punch test etc. to confirm the integrity and assessment of safe operating life of the component. This paper highlights design objective of boat sampling technique, description of sampling module, sampling cutter and its performance evaluation, cutting process, boat samples, operational sequence of sampling module, qualification of sampling module, qualification of sampling technique, qualification of scooped region of the parent material, sample retrieval system, inspection, testing and examination to be carried out on the boat samples and scooped region. (author)

Characterization of 2024-T3: An aerospace aluminum alloy

International Nuclear Information System (INIS)

Huda, Zainul; Taib, Nur Iskandar; Zaharinie, Tuan

2009-01-01

The 2024-T3 aerospace aluminum alloy, reported in this investigation, was acquired from a local aerospace industry: Royal Malaysian Air Force (RMAF). The heat treatable 2024-T3 aluminum alloy has been characterized by use of modern metallographic and material characterization techniques (e.g. EPMA, SEM). The microstructural characterization of the metallographic specimen involved use of an optical microscope linked with a computerized imaging system using MSQ software. The use of EPMA and electron microprobe elemental maps enabled us to detect three types of inclusions: Al-Cu, Al-Cu-Fe-Mn, and Al-Cu-Fe-Si-Mn enriched regions. In particular, the presence of Al 2 CuMg (S-phase) and the CuAl 2 (θ') phases indicated precipitation strengthening in the aluminum alloy

[Motor capacities involved in the psychomotor skills of the cardiopulmonary resuscitation technique: recommendations for the teaching-learning process].

Science.gov (United States)

Miyadahira, A M

2001-12-01

It is a bibliographic study about the identification of the motor capacities involved in the psychomotor skills of the cardiopulmonary resuscitation (CPR) which aims to obtain subsidies to the planning of the teaching-learning process of this skill. It was found that: the motor capacities involved in the psychomotor skill of the CPR technique are predominantly cognitive and motor, involving 9 perceptive-motor capacities and 8 physical proficiency capacities. The CPR technique is a psychomotor skill classified as open, done in series and categorized as a thin and global skill and the teaching-learning process of the CPR technique has an elevated degree of complexity.

Stakeholder involvement techniques. A short guide and annotated bibliography

International Nuclear Information System (INIS)

2005-01-01

The Forum on Stakeholder Confidence (FSC) was created under a mandate from the Radioactive Waste Management Committee (RWMC) of the OECD Nuclear Energy Agency (NEA) to facilitate the sharing of international experience in addressing the societal dimension of radioactive waste management. It explores means of ensuring an effective dialogue amongst all stakeholders, and considers ways to strengthen confidence in decision-making processes. FSC documents may be obtained online at www.nea.fr/html/rwrnifsc.html. OECD countries are increasingly implementing forms of participatory democracy that will require new or enhanced forms of dialogue amongst a broader range of concerned parties. The 4. regular FSC meeting held in Paris in May 2003 included a topical session on Stakeholder involvement tools: Criteria for choice and evaluation. The internal Minutes of the 4. meeting noted, in response to the discussions initiated by this topical session: 'Given that FSC members have one specific issue - radioactive waste management (RWM) - to deal with, a continuing relationship and dialogue among stakeholders seems important. What is desired is a well-informed citizen, because this is - in the end - an issue of democracy. Perhaps we have suffered in our field from a lack of recognition that RWM, like others, is an issue of democracy as well as a technical one'. At the close of the topical session, it was agreed that the FSC would prepare a short guide on stakeholder involvement techniques. The present guide approaches the topic from the point of view of radioactive waste management. However, because dialogue and deliberation techniques can be used in many fields, it will be of interest to a wide readership. It includes an annotated bibliography pointing to easily accessible handbooks and other resources. (author)

Characterization of 2024-T3: An aerospace aluminum alloy

Energy Technology Data Exchange (ETDEWEB)

Huda, Zainul [Department of Mechanical Engineering, University of Malaya, Kuala Lumpur (Malaysia)], E-mail: drzainulhuda@hotmail.com; Taib, Nur Iskandar [Department of Geology, University of Malaya, Kuala Lumpur (Malaysia)], E-mail: ntaib@alumni.indiana.edu; Zaharinie, Tuan [Department of Mechanical Engineering, University of Malaya, Kuala Lumpur (Malaysia)], E-mail: rinie_3483@hotmail.com

2009-02-15

The 2024-T3 aerospace aluminum alloy, reported in this investigation, was acquired from a local aerospace industry: Royal Malaysian Air Force (RMAF). The heat treatable 2024-T3 aluminum alloy has been characterized by use of modern metallographic and material characterization techniques (e.g. EPMA, SEM). The microstructural characterization of the metallographic specimen involved use of an optical microscope linked with a computerized imaging system using MSQ software. The use of EPMA and electron microprobe elemental maps enabled us to detect three types of inclusions: Al-Cu, Al-Cu-Fe-Mn, and Al-Cu-Fe-Si-Mn enriched regions. In particular, the presence of Al{sub 2}CuMg (S-phase) and the CuAl{sub 2} ({theta}') phases indicated precipitation strengthening in the aluminum alloy.

Metallographic examinations of the wear-marks on fuel pins of the KNK II/2 fuel assembly NY-308

International Nuclear Information System (INIS)

Patzer, G.

1987-12-01

On the fuel pins and pin spacers of the fuel assembly NY-308 of the second core of KNK II pronounced wear marks had been found in the area of the contact points. In order to determine the exact form of the marks, metallographic investigations were performed on two test pieces of fuel pins in the Hot Cells of the KfK Karlsruhe. It was found that the wear marks did show the already observed stratified structure. Next to the unchanged cladding area there is a peripheral zone with modified grain structure, followed by a layer of moved material and finally there is a flake-like zone of accumulated cladding material at the lower end of the wear marks. Longitudinal cuts do not show grain deformations, which could indicate axial friction forces between pin and spacer. The wear marks are rapidly dropping to their maximum depth at the ends and the depth shows a relatively uniform pattern between both. The findings are confirming the picture, that a stirring movement of the fuel pins took place, which caused adhesive wear [de

Metallographic study of reconstitution welding in inserts of 1 cm{sup 3}; Estudio metalografico de soldaduras de reconstitucion en insertos de 1 cm{sup 3}

Energy Technology Data Exchange (ETDEWEB)

Romero C, J.; Garcia R, R.; Fernandez T, F.; Perez R, N.; Rocamontes A, M. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)

2007-07-01

In this article, the welding metallographic study carried out in Charpy test tubes reconstituted with notch in 'V', used in the surveillance programs of the vessel in nucleo electric plants is described. Inserts of 1 cm{sup 3} are used, where the inserts are usually rectangular of minimum 18 millimeters of length. The importance of using inserts of 1 cm{sup 3} is that the mechanical properties can be measured in another direction of the vessel steel, when changing the direction or sense of the notch in 'V' or the face where this notch is made in the insert. (Author)

A comparison of five elicitation techniques for elicitation of attributes of low involvement products

DEFF Research Database (Denmark)

Bech-Larsen, Tino; Nielsen, Niels Asger

1999-01-01

of dimensions directed from theories of consumer buying behaviour. Although a number of differences between the techniques are identified in the study, the main findings are that the robustness of the different techniques for attribute elicitation is considerable Udgivelsesdato: JUN......The critical first step for most instruments used in analysing consumer choice and motivation is the identification of product attributes which are important to the consumer and for which there are differences among the available product alternatives. A number of techniques, ranging from...... the complex elicitation of idiosyncratic attributes or simpler picking procedures, has been developed to elicitate such attributes. The purpose of the study presented here is to com-pare attributes of a low involvement product, viz. vegetable oil, elicited by five different techniques on a number...

Progress involving new techniques for liposome preparation

Directory of Open Access Journals (Sweden)

Zhenjun Huang

2014-08-01

Full Text Available The article presents a review of new techniques being used for the preparation of liposomes. A total of 28 publications were examined. In addition to the theories, characteristics and problems associated with traditional methods, the advantages and drawbacks of the latest techniques were reviewed. In the light of developments in many relevant areas, a variety of new techniques are being used for liposome preparation and each of these new technique has particular advantages over conventional preparation methods. However, there are still some problems associated with these new techniques that could hinder their applications and further improvements are needed. Generally speaking, due to the introduction of these latest techniques, liposome preparation is now an improved procedure. These applications promote not only advances in liposome research but also the methods for their production on an industrial scale.

Prediction of size and position of fracture relevant defects of samples fatigued in the VHCF area on the basis of metallographic examinations; Vorhersage der Groesse und der Lage bruchrelevanter Defekte von im VHCF-Bereich ermuedeter Proben auf Basis metallographischer Untersuchungen

Energy Technology Data Exchange (ETDEWEB)

Christ, Hans-Juergen; Grigorescu, Andrei; Kolyshkin, Anton [Siegen Univ. (Germany). Inst. fuer Werkstofftechnik; Kaufmann, Edgar [Siegen Univ. (Germany). Dept. Mathematik; Zimmermann, Martina [TU Dresden (Germany). Inst. fuer Werkstoffwissenschaft

2016-07-15

This paper aims to examine the connection between the material quality with regard to the size and spatial distribution of the defects and the size or position of the defects causing the fracture which determine the durability of components in the range of Very High Cycle Fatigue (VHCF). For this purpose, the quality of the metastable austenitic steel 1.4301 was characterized via metallographic examinations. Longitudinal and cross sections were taken from a sheet steel. Afterwards size and position of all defects were measured. The metallographic information acquired was used to create a statistical defect distribution model. On the basis of this model and the stress distribution in the most stressed area of the used fatigue samples, the distribution of size and position of the inclusions relevant for the fatigue failure could be predicted. The results of the modelling are in good agreement with the experimental observations regarding the positions of crack initiation on samples failing under VHCF circumstances.

Intermetallic precipitation in rare earth-treated A413.1 alloy. A metallographic study

International Nuclear Information System (INIS)

Samuel, Agnes M.; Samuel, Fawzy H.

2018-01-01

The present study was performed mainly on A413.1 alloy. Measured amounts of La, Ce or La+Ce, Ti and Sr were added to the molten alloy in the form of master alloys. Samples sectioned from castings obtained from thermal analysis experiments were used for preparing samples for metallographic examination. The results show that addition of rare earth (RE) metals to Al-Si alloys increased the α-Al nucleation temperature and depressed the Al-Si eutectic formation temperature, thereby increasing the solidification range. Depending upon the alloying elements/additives, a large number of RE-based intermetallics could be formed: Al 4 (Ce,La), Al 13 (Ce,La) 2 Cu 3 , Al 7 (Cu,Fe) 6 (Ce,La) 6 Si 2 , Al 4 La, Al 2 La 5 Si 2 , Al 2 Ce 5 Si 2 , Al 2 (Ce,La) 5 Si 2 . Under an electron microscope, these phases appear in backscatter imaging mode in the form of thin grayish-white platelets on the dark gray Al matrix. The average thickness of these platelets is about 1.5 μm. When the alloy is grain refined with Ti-based master alloys, precipitation of a gray phase in the form of sludge is observed: Al 12 La 3 Ti 2 , or Al 12 (Ce,La) 3 Ti 2 . Regardless the alloy composition, the RE/Al ratios remain constant in each type of intermetallic. Rare earth metals have a strong affinity to react with Sr (resulting in partial modification of the eutectic Si particles) as well as some transition elements, in particular Ti and Cu. Iron has a very low affinity for interaction with RE metals. It is only confined to Fe-based intermetallics.

Intermetallic precipitation in rare earth-treated A413.1 alloy. A metallographic study

Energy Technology Data Exchange (ETDEWEB)

Samuel, Agnes M.; Samuel, Fawzy H. [Univ. du Quebec a Chicoutimi (Canada). Dept. des Sciences Appliquees; Doty, Herbert W. [General Motors, Pontiac, MI (United States). Materials Engineering; Valtierra, Salvador [Nemak, S.A., Garza Garcia (Mexico)

2018-02-15

The present study was performed mainly on A413.1 alloy. Measured amounts of La, Ce or La+Ce, Ti and Sr were added to the molten alloy in the form of master alloys. Samples sectioned from castings obtained from thermal analysis experiments were used for preparing samples for metallographic examination. The results show that addition of rare earth (RE) metals to Al-Si alloys increased the α-Al nucleation temperature and depressed the Al-Si eutectic formation temperature, thereby increasing the solidification range. Depending upon the alloying elements/additives, a large number of RE-based intermetallics could be formed: Al{sub 4}(Ce,La), Al{sub 13}(Ce,La){sub 2}Cu{sub 3}, Al{sub 7}(Cu,Fe){sub 6}(Ce,La){sub 6}Si{sub 2}, Al{sub 4}La, Al{sub 2}La{sub 5}Si{sub 2}, Al{sub 2}Ce{sub 5}Si{sub 2}, Al{sub 2}(Ce,La){sub 5}Si{sub 2}. Under an electron microscope, these phases appear in backscatter imaging mode in the form of thin grayish-white platelets on the dark gray Al matrix. The average thickness of these platelets is about 1.5 μm. When the alloy is grain refined with Ti-based master alloys, precipitation of a gray phase in the form of sludge is observed: Al{sub 12}La{sub 3}Ti{sub 2}, or Al{sub 12}(Ce,La){sub 3}Ti{sub 2}. Regardless the alloy composition, the RE/Al ratios remain constant in each type of intermetallic. Rare earth metals have a strong affinity to react with Sr (resulting in partial modification of the eutectic Si particles) as well as some transition elements, in particular Ti and Cu. Iron has a very low affinity for interaction with RE metals. It is only confined to Fe-based intermetallics.

Metallographic autopsies of full-scale ITER prototype cable-in-conduit conductors after full testing in SULTAN: 1. The mechanical role of copper strands in a CICC

International Nuclear Information System (INIS)

Sanabria, Carlos; Lee, Peter J; Starch, William; Blum, Timothy; Larbalestier, David C; Devred, Arnaud; Jewell, Matthew C; Pong, Ian; Martovetsky, Nicolai

2015-01-01

Cables made with Nb 3 Sn-based superconductor strands will provide the 13 T maximum peak magnetic field of the ITER central solenoid (CS) coils and they must survive up to 60 000 electromagnetic cycles. Accordingly, prototype designs of CS cable-in-conduit-conductors (CICC) were electromagnetically tested over multiple magnetic field cycles and warm-up-cool-down scenarios in the SULTAN facility at CRPP. We report here a post-mortem metallographic analysis of two CS CICC prototypes which exhibited some rate of irreversible performance degradation during cycling. The standard ITER CS CICC cable design uses a combination of superconducting and Cu strands, and because the Lorentz force on the strand is proportional to the transport current in the strand, removing the copper strands (while increasing the Cu:SC ratio of the superconducting strands) was proposed as one way of reducing the strand load. In this study we compare the two alternative CICCs, with and without Cu strands, keeping in mind that the degradation after the SULTAN test was lower for the CICC without Cu strands. The post-mortem metallographic evaluation revealed that the overall strand transverse movement was 20% lower in the CICC without Cu strands and that the tensile filament fractures found were less, both indications of an overall reduction in high tensile strain regions. It was interesting to see that the Cu strands in the mixed cable design (with higher degradation) helped reduce the contact stresses on the high pressure side of the CICC, but in either case, the strain reduction mechanisms were not enough to suppress cyclic degradation. Advantages and disadvantages of each conductor design are discussed here aimed to understand the sources of the degradation. (paper)

Characterization of duplex stainless steels by TEM [transmission electron microscopy], SANS [small-angle neutron scattering], and APFIM [atom-probe field ion microscopy] techniques

International Nuclear Information System (INIS)

Chung, H.M.; Chopra, O.K.

1987-06-01

Results are presented of complementary characterization of aged duplex stainless steels by advanced metallographic techniques, including transmission and high-voltage electron microscopies; small-angle neutron scattering; and atom-probe field ion microscopy. On the basis of the characterization, the mechanisms of aging embrittlement have been shown to be associated with the precipitation of Ni- and Si-rich G phase and Cr-rich α' in the ferrite, and M 23 C 6 carbides on the austenite-ferrite phase boundaries. 19 refs., 19 figs., 1 tab

Fluorescence microscopy for the characterization of structural integrity

Science.gov (United States)

Street, Kenneth W.; Leonhardt, Todd A.

1991-01-01

The absorption characteristics of light and the optical technique of fluorescence microscopy for enhancing metallographic interpretation are presented. Characterization of thermally sprayed coatings by optical microscopy suffers because of the tendency for misidentification of the microstructure produced by metallographic preparation. Gray scale, in bright field microscopy, is frequently the only means of differentiating the actual structural details of porosity, cracking, and debonding of coatings. Fluorescence microscopy is a technique that helps to distinguish the artifacts of metallographic preparation (pullout, cracking, debonding) from the microstructure of the specimen by color contrasting structural differences. Alternative instrumentation and the use of other dye systems are also discussed. The combination of epoxy vacuum infiltration with fluorescence microscopy to verify microstructural defects is an effective means to characterize advanced materials and to assess structural integrity.

Attributes of low involvement products: A comparison of five elicitation techniques and a test of their nomological validity

DEFF Research Database (Denmark)

Bech-Larsen, Tino; Nielsen, Niels Asger; Grunert, Klaus G.

attributes, which are important to consumers, is the critical first step in the majority of consumer behavior studies. 2. A number of techniques, ranging from the complicated elicitation of idiosyncratic attributes, to simpler techniques, as picking from a pre-specified list of attributes, has been developed...... negatively to the abstraction level and the number of attributes involved in the choice task. 4. The purpose of the study presented in this paper is to: (a) compare different elicitation techniques on a number of different criteria, such as: importance to consumers, ability to discriminate between brands......, predictive ability, time use, and number of attributes elicited; and to (b) test the nomological validity of the basic assumptions regarding attributes and consumer choices for a low involvement product (veg oil). 5. The study presented is part of the project Rape seed oil for human consumption. Although...

Post-pulse detail metallographic examinations of low-enriched uranium silicide plate-type miniature fuel

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki

1991-10-01

Pulse irradiation at Nuclear Safety Research Reactor (NSRR) was performed using low-enriched (19.89 w% 235 U) unirradiated silicide plate-type miniature fuel which had a density of 4.8 gU/cm 3 . Experimental aims are to understand the dimensional stability and to clarify the failure threshold of the silicide plate-type miniature fuel under power transient conditions through post-pulse detail metallographic examinations. A silicide plate-type miniature fuel was loaded into an irradiation capsule and irradiated by a single pulse. Deposited energies given in the experiments were 62, 77, 116 and 154 cal/g·fuel, which lead to corresponding peak fuel plate temperatures, 201 ± 28degC, 187 ± 10degC, 418 ± 74degC and 871 ± 74degC, respectively. Below 400degC, reliability and dimensional stability of the silicide plate fuel was sustained, and the silicide plate fuel was intact. Up to 540degC, wall-through intergranular crackings occurred in the Al-3%Mg alloy cladding. With the increase of the temperature, the melting of the aluminum cladding followed by recrystallization, the denudation of fuel core and the plate-through intergranular cracking were observed. With the increase of the temperature beyond 400degC, the bowing of fuel plate became significant. Above the temperature of 640degC molten aluminum partially reacted with the fuel core, partially flowed downward under the influence of surface tension and gravity, and partially formed agglomerations. Judging from these experimental observations, the fuel-plate above 400degC tends to reduce its dimensional stability. Despite of the apparent silicide fuel-plate failure, neither generation of pressure pulse nor that of mechanical energy occurred at all. (J.P.N.)

Novel radiotherapy techniques for involved-field and involved-node treatment of mediastinal Hodgkin lymphoma. When should they be considered and which questions remain open

Energy Technology Data Exchange (ETDEWEB)

Lohr, Frank; Koeck, Julia; Abo-Madyan, Yasser [University of Heidelberg, Department of Radiation Oncology, University Medical Center Mannheim, Mannheim (Germany); Georg, Dietmar; Knaeusl, Barbara; Dieckmann, Karin [Medical University Vienna/AKH Vienna, Department of Radiation Oncology, Comprehensive Cancer Center, Vienna (Austria); Medical University Vienna/AKH Vienna, Christian Doppler Laboratory for Medical Radiation Research for Radiation Oncology, Comprehensive Cancer Center, Vienna (Austria); Cozzi, Luca [Medical Physics Unit, Oncology Institute of Southern Switzerland, Bellinzona (Switzerland); Eich, Hans Theodor [University Hospital, Department of Radiotherapy, Muenster (Germany); Weber, Damien C. [Paul Scherrer Institute, University of Bern, Center for Proton Therapy, Bern (Switzerland); Fiandra, Christian; Ricardi, Umberto [University of Torino, Radiation Oncology Unit, Department of Oncology, Turin (Italy); Mueller, Rolf-Peter [University of Cologne, Department of Radiation Oncology, Cologne (Germany); Engert, Andreas [University of Cologne, Department of Medical Oncology, Cologne (Germany)

2014-10-15

Hodgkin lymphoma (HL) is a highly curable disease. Reducing late complications and second malignancies has become increasingly important. Radiotherapy target paradigms are currently changing and radiotherapy techniques are evolving rapidly. This overview reports to what extent target volume reduction in involved-node (IN) and advanced radiotherapy techniques, such as intensity-modulated radiotherapy (IMRT) and proton therapy-compared with involved-field (IF) and 3D radiotherapy (3D-RT)- can reduce high doses to organs at risk (OAR) and examines the issues that still remain open. Although no comparison of all available techniques on identical patient datasets exists, clear patterns emerge. Advanced dose-calculation algorithms (e.g., convolution-superposition/Monte Carlo) should be used in mediastinal HL. INRT consistently reduces treated volumes when compared with IFRT with the exact amount depending on the INRT definition. The number of patients that might significantly benefit from highly conformal techniques such as IMRT over 3D-RT regarding high-dose exposure to organs at risk (OAR) is smaller with INRT. The impact of larger volumes treated with low doses in advanced techniques is unclear. The type of IMRT used (static/rotational) is of minor importance. All advanced photon techniques result in similar potential benefits and disadvantages, therefore only the degree-of-modulation should be chosen based on individual treatment goals. Treatment in deep inspiration breath hold is being evaluated. Protons theoretically provide both excellent high-dose conformality and reduced integral dose. Further reduction of treated volumes most effectively reduces OAR dose, most likely without disadvantages if the excellent control rates achieved currently are maintained. For both IFRT and INRT, the benefits of advanced radiotherapy techniques depend on the individual patient/target geometry. Their use should therefore be decided case by case with comparative treatment planning

High-temperature metallography setup

International Nuclear Information System (INIS)

Blumenfeld, M.; Shmarjahu, D.; Elfassy, S.

1979-06-01

A high-temperature metallography setup is presented. In this setup the observation of processes such as that of copper recrystallization was made possible, and the structure of metals such as uranium could be revealed. A brief historical review of part of the research works that have been done with the help of high temperature metallographical observation technique since the beginning of this century is included. Detailed description of metallographical specimen preparation technique and theoretical criteria based on the rate of evaporation of materials present on the polished surface of the specimens are given

Analysis of metal samples

International Nuclear Information System (INIS)

Ramirez T, J.J.; Lopez M, J.; Sandoval J, A.R.; Villasenor S, P.; Aspiazu F, J.A.

2001-01-01

An elemental analysis, metallographic and of phases was realized in order to determine the oxidation states of Fe contained in three metallic pieces: block, plate and cylinder of unknown material. Results are presented from the elemental analysis which was carried out in the Tandem Accelerator of ININ by Proton induced X-ray emission (PIXE). The phase analysis was carried out by X-ray diffraction which allowed to know the type of alloy or alloys formed. The combined application of nuclear techniques with metallographic techniques allows the integral characterization of industrial metals. (Author)

Techniques involving extreme environment, nondestructive techniques, computer methods in metals research, and data analysis

International Nuclear Information System (INIS)

Bunshah, R.F.

1976-01-01

A number of different techniques which range over several different aspects of materials research are covered in this volume. They are concerned with property evaluation of 4 0 K and below, surface characterization, coating techniques, techniques for the fabrication of composite materials, computer methods, data evaluation and analysis, statistical design of experiments and non-destructive test techniques. Topics covered in this part include internal friction measurements; nondestructive testing techniques; statistical design of experiments and regression analysis in metallurgical research; and measurement of surfaces of engineering materials

Metallographic examinations of Type 304 stainless steel (heat 9T2796) tested in high-temperature uniaxial and multiaxial experiments

Energy Technology Data Exchange (ETDEWEB)

Swindeman, R.W.; Houck, C.W.

1984-03-01

The results obtained from a number of metallographic examinations of Type 304 stainless steel specimens were compiled. Samples were obtained from uniaxial and multiaxial tests covering a very broad span of temperatures and times. Special emphasis was on the identification of failure modes, cracking patterns, grain distortion, and grain-boundary microstructures. Uniaxial specimens exhibited the following sequence of failure modes with increasing temperature and time: ductile plastic tearing, ductile plastic shear, wedge cracking, and microvoid cracking. Over most of the temperature range examined (482 to 871/sup 0/C), M/sub 23/C/sub 6/ precipitated on grain boundaries at long times. Sigma phase and possibly ferrite were often present in the stressed areas at temperatures as low as 482/sup 0/C (900/sup 0/F). These metallurgical features promoted a severe loss in creep ductility at long times and low temperatures. Most multiaxial tests were performed under conditions that promoted wedge cracking. Stress gradients also favored surface crack initiation rather than bulk damage. Testing times for multiaxial tests were less than 10,000 h; hence, there was insufficient time for the development of embrittling features such as microvoids, sigma, and ferrite. Long-time multiaxial tests to failure are recommended.

Dam geology and basic treatment(2). Adit substitution technique and measures against landslide involved in excavation

Energy Technology Data Exchange (ETDEWEB)

Shimizu, Kin' ichi [Kinki Geological Center, Co. Ltd., Kyoto, Japan (JP)

1988-12-25

This paper discusses the adit substitution technique which is a method for special treatment of dams and measures against landslide involved in excavation. The adit substitution technique consists of excavating an adit in the natural ground, excavating another adit which is in contact with the first adit and is at a level higher than the first adit, placing concrete from the upper adit to the lower adit to fill first adit completely with concrete, excavating a third adit, filling the second adit with concrete similarly, and proceeding with this process to construct a water barrier within the natural ground until the water barrier reaches the required height. The paper explains examples of this technique used on four dams. It also explains examples of measures against excavation-induced landslide adopted on three dams. 13 refs., 8 figs., 2 tabs.

Techniques for intergranular crack formation and assessment in alloy 600 base and alloy 182 weld metals

International Nuclear Information System (INIS)

Lee, Tae Hyun; Hwang, Il Soon; Kim, Hong Deok; Kim, Ji Hyun

2015-01-01

A technique developed to produce artificial intergranular stress corrosion cracks in structural components was applied to thick, forged alloy 600 base and alloy 182 weld metals for use in the qualification of nondestructive examination techniques for welded components in nuclear power plants. An externally controlled procedure was demonstrated to produce intergranular stress corrosion cracks that are comparable to service-induced cracks in both the base and weld metals. During the process of crack generation, an online direct current potential drop method using array probes was used to measure and monitor the sizes and shapes of the cracks. A microstructural characterization of the produced cracks revealed realistic conformation of the crack faces unlike those in machined notches produced by an electrodischarge machine or simple fatigue loading using a universal testing machine. A comparison with a destructive metallographic examination showed that the characteristics, orientations, and sizes of the intergranular cracks produced in this study are highly reproducible.

Metallography

International Nuclear Information System (INIS)

Dieser, K.; Kopp, W.U.; Paul, J.; Wallura, E.

1986-01-01

On the 9th-11th October 1985, the annual Metallography Conference (Metallographie-Tagung) took place in Europahalle, Trier. The following items were discussed: Metallography of soldering and welding - Metallographic examinations of corrosion processes - Structural and material properties - Metallographic preparation techniques - Metallography of corrosion and wear protection coatings. Also this time, most of the speakers' manuscripts were made available in the booklet 'Sonderband 17'. This is a comprehensive outline of the present view in metallographic examination methods on the above mentioned subjects. All participants in the production of this booklet are gratefully acknowledged for their intensive yet speedy work. 10 contributions have been separately analyzed in the ENERGY data base. (orig.) [de

Effect of using the double layer technique on the microstructure, microhardness and residual stress of welded ASTM A516 GR70 structural steel

International Nuclear Information System (INIS)

Oliveira, George Luiz Gomes de; Miranda, Helio Cordeiro de

2010-01-01

The aim of this work is to evaluate the effect of using the double layer technique on the microstructure, microhardness and residual stresses of welded ASTM A516 Gr70 structural steel. Samples were welded with the same welding parameters and two types of chamfers, while the samples welded using the double layer technique underwent a buttering process on their chamfer face. Residual stress measurement was accomplished through x-ray diffraction, using a mini diffractometer for measurement in field. Metallographic analysis was accomplished in the transverse section of the welded joint, using optic microscopy and scanning electron microscopy. The double layer technique showed that can be used in the welding of ASTM A516 Gr70 steel, because, besides promote a refinement and a drawing back of the CG-HAZ, it increased compressive residual stress in the whole surface of the analyzed samples.(author)

The metallographic examination of sword no. 438 as part of a systematic survey of swords from the early medieval stronghold of Mikulčice, Czech Republic

Directory of Open Access Journals (Sweden)

Hošek, Jiří

2012-12-01

Full Text Available The paper deals with a metallographic examination of a sword from grave No. 438, which was uncovered at the site of Mikulčice (Hodonín county, a former early medieval stronghold in Moravia (Czech Republic. Mikulčice was one of the main power centres of the Great Moravia – the first state formed by Slavs north of the Danube River – which was created in the first third of the 9th century and ended at the beginning of the 10th century. The sword, provided with a single flattened hemispherical pommel (Petersen X type, has a blade bearing an inscription that is no longer legible. According to the results of metallographic examination, the blade was hardened and consists of steel cutting edges welded on a core, which was composed of steel side-plates and a middle strip of iron or low-carbon steel. It was an excellent sword, undoubtedly one of the best swords excavated in Mikulčice.

El artículo trata de un examen metalográfico de una espada de la tumba número 438, que fue descubierta en el yacimiento de Mikulčice (Hodonín Condado, antiguo bastión bajomedieval en Moravia (República Checa. Mikulčice fue uno de los centros de poder principales del Gran Moravia - la primera agrupación estatal de los eslavos del norte del río Danubio - que se creó en el primer tercio del siglo IX y fue abolido al comienzo del siglo X. La espada, que cuenta con un pomo aplanado hemiesféri-co (Petersen tipo X, tiene una hoja con una inscripción que ya no es legible. De acuerdo con los resulta-dos del examen metalográfico, la hoja fue endurecida y se compone de filos de corte de acero, soldados a un núcleo. Éste está compuesto de placas laterales de acero y una franja central de hierro o de acero dulce. Era una espada excelente, sin duda, una de las mejores espadas jamás excavadas en Mikulčice.

Multi-channel Spiral Twist Extrusion (MCSTE): A Novel Severe Plastic Deformation Technique for Grain Refinement

Science.gov (United States)

El-Garaihy, W. H.; Fouad, D. M.; Salem, H. G.

2018-04-01

Multi-channel Spiral Twist Extrusion (MCSTE) is introduced as a novel severe plastic deformation (SPD) technique for producing superior mechanical properties associated with ultrafine grained structure in bulk metals and alloys. The MCSTE design is based on inserting a uniform square cross-sectioned billet within stacked disks that guarantee shear strain accumulation. In an attempt to validate the technique and evaluate its plastic deformation characteristics, a series of experiments were conducted. The influence of the number of MCSTE passes on the mechanical properties and microstructural evolution of AA1100 alloy were investigated. Four passes of MCSTE, at a relatively low twisting angle of 30 deg, resulted in increasing the strength and hardness coupled with retention of ductility. Metallographic observations indicated a significant grain size reduction of 72 pct after 4 passes of MCSTE compared with the as-received (AR) condition. Moreover, the structural uniformity increased with the number of passes, which was reflected in the hardness distribution from the peripheries to the center of the extrudates. The current study showed that the MCSTE technique could be an effective, adaptable SPD die design with a promising potential for industrial applications compared to its counterparts.

Effectiveness of a Treatment Involving Soft Tissue Techniques and/or Neural Mobilization Techniques in the Management of Tension-Type Headache: A Randomized Controlled Trial.

Science.gov (United States)

Ferragut-Garcías, Alejandro; Plaza-Manzano, Gustavo; Rodríguez-Blanco, Cleofás; Velasco-Roldán, Olga; Pecos-Martín, Daniel; Oliva-Pascual-Vaca, Jesús; Llabrés-Bennasar, Bartomeu; Oliva-Pascual-Vaca, Ángel

2017-02-01

To evaluate the effects of a protocol involving soft tissue techniques and/or neural mobilization techniques in the management of patients with frequent episodic tension-type headache (FETTH) and those with chronic tension-type headache (CTTH). Randomized, double-blind, placebo-controlled before and after trial. Rehabilitation area of the local hospital and a private physiotherapy center. Patients (N=97; 78 women, 19 men) diagnosed with FETTH or CTTH were randomly assigned to groups A, B, C, or D. (A) Placebo superficial massage; (B) soft tissue techniques; (C) neural mobilization techniques; (D) a combination of soft tissue and neural mobilization techniques. The pressure pain threshold (PPT) in the temporal muscles (points 1 and 2) and supraorbital region (point 3), the frequency and maximal intensity of pain crisis, and the score in the Headache Impact Test-6 (HIT-6) were evaluated. All variables were assessed before the intervention, at the end of the intervention, and 15 and 30 days after the intervention. Groups B, C, and D had an increase in PPT and a reduction in frequency, maximal intensity, and HIT-6 values in all time points after the intervention as compared with baseline and group A (P<.001 for all cases). Group D had the highest PPT values and the lowest frequency and HIT-6 values after the intervention. The application of soft tissue and neural mobilization techniques to patients with FETTH or CTTH induces significant changes in PPT, the characteristics of pain crisis, and its effect on activities of daily living as compared with the application of these techniques as isolated interventions. Copyright © 2016 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Metallographic approach to the damage of austenitic stainless steels under plastic fatigue or under creep: description and physical interpretation of fatigue-creep-oxidation interactions

International Nuclear Information System (INIS)

Levaillant, Christophe

1984-01-01

This research thesis reports the study of interactions between fatigue, creep and oxidation in austenitic stainless steels which are to be used in the construction of fast breeder reactors. This study is addressed by means of low cycle plastic fatigue test with imposed strain, performed at 600 C with tensile relaxation hold times which may reach 24 hours. Continuous fatigue tests (without hold time) and pure creep tests have also been performed to define 'pure' fatigue damages and 'pure' creep damages. Two grades of Z3 CND 17-13 steel have been studied. Thus fracture mechanisms, crack initiation and propagation, and crack kinetic propagation have been studied. Metallographic measurements of damage have been performed. Damage types have been identified: propagation of cracks initiated at the surface, and intergranular de-cohesion within the material. An approximate modelling is proposed, as well as a critical comparison of various published models of fatigue-creep interaction. In order to predict structure lifetime, a new test methodology is proposed, based on experimental results

Facilities for post-irradiation examination of experimental fuel elements at Chalk River Nuclear Laboratories

International Nuclear Information System (INIS)

Mizzan, E.; Chenier, R.J.

1979-10-01

Expansion of post-irradiation facilities at the Chalk River Nuclear Laboratories and steady improvement in hot-cell techniques and equipment are providing more support to Canada's reactor fuel development program. The hot-cell facility primarily used for examination of experimental fuels averages a quarterly throughput of 40 elements and 110 metallographic specimens. New developments in ultrasonic testing, metallographic sample preparation, active storage, active waste filtration, and fissile accountability are coming into use to increase the efficiency and safety of hot-cell operations. (author)

Equipment of the metallographic cell n. 10 in the irradiated fuel element laboratories (L.E.C.L); Equipement de la cellule de metallographie n. 10 du L.E.C.I

Energy Technology Data Exchange (ETDEWEB)

Roussel, E; Vignesoult, N [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1963-07-01

A conventional metallographic apparatus has been adapted for work in a protected cell. The small size of the apparatus and the placing of this apparatus simply on a working bench which can easily be dismantled make it possible on the one hand to repair the apparatus easily in the event of a breakdown, and on the other hand to decontaminate it fairly easily without the presence of a technician in the cell. (authors) [French] Une installation de metallographie classique a ete adaptee au travail en cellule blindee. Le faible encombrement des appareils, le simple positionnement de ces derniers sur un plan de travail facilement demontable permettent, d'une part un demontage aise en cas de panne, d'autre part une decontamination qui peut se faire pratiquement sans intervention d'un agent dans la cellule. (auteurs)

Techniques for intergranular crack formation and assessment in alloy 600 base and alloy 182 weld metals

Directory of Open Access Journals (Sweden)

Tae Hyun Lee

2015-02-01

Conclusion: A comparison with a destructive metallographic examination showed that the characteristics, orientations, and sizes of the intergranular cracks produced in this study are highly reproducible.

Requalification of the 235-F Metallograph Facility gloveboxes for use in the 773-A plutonium immobilization demonstration

International Nuclear Information System (INIS)

Hinds, S.S.; Hidlay, J.

1997-01-01

A concern has been identified regarding the viability of redesigning and requalifying existing glovebox lines for use as glovebox lines integral to future mission activities in the 773-A laboratory building at the Savannah River Site (SRS). The Bechtel Savannah River Inc. (BSRI) design engineering team has been requested to perform an evaluation which would investigate the reuse of these existing gloveboxes versus the procurement of completely new glovebox systems. The existing glovebox lines were manufactured for the Plutonium (Pu) Metallograph Facility, Project 3253, located in building 235-F at SRS. These gloveboxes were designed as independent, fully functional Pu 'metal' and Pu 'oxide' processing glovebox systems for this facility. These gloveboxes, although fully installed, have never processed radioactive material. The proposed use for these gloveboxes are: (1) to utilize the Pu 'metal' glovebox system for the primary containment associated with the Pre-Processing/Re-Processing Laboratory for obtaining radioactive glass compound viscometer analysis and (2) to utilize the Pu 'oxide' glovebox system for primary containment associated with the Pu 'Can in Can' Demonstration for proof of principle testing specific to long term Pu immobilization and storage technology. This report presents objective evidence that supports the engineering judgment indicating the existing gloveboxes can be requalified for the proposed uses indicated above. SRS has the ability to duplicate the test parameters, with site forces, that will meet or exceed the identical acceptance criteria established to qualify the existing gloveboxes. The qualification effort will be a documented procedure using the leak test criteria characteristic of the original glovebox purchase. Two equivalent tests will be performed, one for post modification leak test acceptance and one for post installation leak test acceptance. (Abstract Truncated)

Dosimetric studies, spectrometric, radiographic, metallographic of a new argentinean seed of 125 I used in brachytherapy

International Nuclear Information System (INIS)

Pirchio, R.; Saravi, M.; Banchik, D.; Munoz, C.

2006-01-01

A new source of 125 I model Braquibac TM has been developed in Argentina for applications in interstitial brachytherapy. The AAPM Task Group 43 (TG-43) recommends that dosimetric characteristics of new sources of brachytherapy of Iodine-125 have been theoretically and experimentally determined before its clinical use. The objectives outlined in this work were the study of the design of the new seed, the calculation of dosimetric parameters and the photons spectra analysis. Its were carried out radiographic and metallographic studies to determine the physical characteristics of the source. For the realization of the dosimetric calculations it was used the Monte Carlo code MCNP5. Values of the radial dose function, g(r), of the constant of dose rate, Λ, of the function of anisotropy of two dimensions, F(r, θ), of the factor and constant of anisotropy its were obtained simulating the source in water according to the recommended methodology in TG-43. The constant of dose rate is similar to 0,880 ± 0,080 c Gy h -1 U -1 . The kerma in air rate of reference, S K , was calculated as 1,036 c Gy cm 2 h -1 mCi -1 simulating the seed in dry air. Its were carried out spectrometric studies using a semiconductor planar detector of HPGe (high purity germanium). Photons spectra showed characteristic x-rays of 125 I with energies of 27,20 keV, 27,47 keV, 31 keV and 31,70 keV gamma photons of 35,5 keV, and x-ray fluorescent coming from the silver nucleus of 22,10 keV, 24,94 keV and 25,45 keV. The angular dependence of the intensity of photons around the seed and in air it was analyzed with the planar detector. This was carried out to study the anisotropy in the photons flow due to variation in the thickness of the titanium wall and of the welding, movements of the silver tube inside the source and deposition of the radioactive material on the silver tube. (Author)

Study of internal oxidation kinetics of molybdenum base alloys

International Nuclear Information System (INIS)

Krushinskij, Yu.Yu.; Belyakov, B.G.; Belomyttsev, M.Yu.

1989-01-01

Metallographic and microdurometric method as well as new technique were used to study kinetics of internal oxidation (IO). It is shown that study of IO kinetics on the base of metallographic measurements of layers depth is not correct because it is related with insufficient sensitivity of the method. IO kinetics under conditions of formation of molybdenum oxide layer on saturated material surface as well as IO of alloy with high carbon content were investigated. Oxide film formation does not affect the IO kinetics; decarburization observed along with oxidation increases the apparent activation energy and K exponent on time dependence of diffusion layer depth

Guidelines for destructive examination of potential MIC [microbiologically influenced corrosion]-related failures

International Nuclear Information System (INIS)

Borenstein, S.S.

1989-01-01

Microbiologically influenced corrosion (MIC) is recognized as a major cause of pitting corrosion failures in natural waters. In order to alleviate the problem, it is important to establish the exact cause of corrosion. If there is a possibility that the failure is due to MIC, a particularly careful failure analysis must be conducted. MIC can be misdiagnosed as attack due to conventional chloride crevice/pitting corrosion unless specialized techniques are used. Certain techniques generally must be employed, including a careful visual examination, is situ bacterial sampling of residual water, bacterial analysis for corrosion products, radiographic examinations, and metallographic examinations. Other techniques may be necessary, or may be very helpful in the analysis, including culture growth, scanning electron microscopy, and ultrasonic examinations. Metallographic examinations can reveal MIC characteristics such as selective pitting of one phase in duplex stainless steel weldments. The methods of failure analysis and their importance are addressed, including each of the steps in the nondestructive examinations and destructive analyses

Supporting Active User Involvment in Prototyping

DEFF Research Database (Denmark)

Grønbæk, Kaj

1990-01-01

The term prototyping has in recent years become a buzzword in both research and practice of system design due to a number of claimed advantages of prototyping techniques over traditional specification techniques. In particular it is often stated that prototyping facilitates the users' involvement...... in the development process. But prototyping does not automatically imply active user involvement! Thus a cooperative prototyping approach aiming at involving users actively and creatively in system design is proposed in this paper. The key point of the approach is to involve users in activities that closely couple...... development of prototypes to early evaluation of prototypes in envisioned use situations. Having users involved in such activities creates new requirements for tool support. Tools that support direct manipulation of prototypes and simulation of behaviour have shown promise for cooperative prototyping...

Additive manufacturing: Characterization of TI-6AI-4V alloy intended for biomedical application

CSIR Research Space (South Africa)

Ramosoeu, ME

2010-10-01

Full Text Available Direct Metal Laser Sintering (DMLS) is one of the new Laser Additive Manufacturing (LAM) techniques used for producing complex topology components mostly found in medical applications. The work presented in this paper focuses on metallographic...

Identification of the zirconium hydrides metallography in zircaloy-2; Contribucion al estudio por metalografia de los hidruros de circonio en Zircaloy-2

Energy Technology Data Exchange (ETDEWEB)

Garcia Gonzalez, F

1968-07-01

Technique for the Identification of the zirconium hydrides in metallographic specimens have been developed. Microhardness, quantitative estimation and relative orientation of the present hydrides as well as grain size determination of the different Zircaloy-2 tube specimens have also been made. The specimens used were corrosion- tested in water during various periods of time at 300 degree castrating, prior to the metallographic examination. Reference specimens, as received, and heavily hydride specimens in a hydrogen atmosphere at 800 degree centigrees, have been used in the previous stages of the work. No difficulties have been met in this early stage of acquaintanceship with the zirconium hydrides. (Author) 5 refs.

Identification of the zirconium hydrides metallography in zircaloy-2

International Nuclear Information System (INIS)

Garcia Gonzalez, F.

1968-01-01

Technique for the Identification of the zirconium hydrides in metallographic specimens have been developed. Microhardness, quantitative estimation and relative orientation of the present hydrides as well as grain size determination of the different Zircaloy-2 tube specimens have also been made. The specimens used were corrosion- tested in water during various periods of time at 300 degree castrating, prior to the metallographic examination. Reference specimens, as received, and heavily hydride specimens in a hydrogen atmosphere at 800 degree centigrees, have been used in the previous stages of the work. No difficulties have been met in this early stage of acquaintanceship with the zirconium hydrides. (Author) 5 refs

Analysis of martensitic transformation and residual tension in an 304L stainless steel; Analise da transformacao martensitica e tensao residual em um aco inoxidavel 304L

Energy Technology Data Exchange (ETDEWEB)

Alves, Juciane Maria

2014-07-01

The relationship between plastic deformation and the strain induced phase transformation, that provides a practical route to the development of new engineering materials with excellent mechanical properties, characterize the TRIP effect 'Transformation Induced Plasticity'. Among the stainless steels, the metastable 304 L austenitic steel is susceptible to transformation of austenite-martensite phase from tensile tests at room temperature by increments of plastic deformation. It is of great technological and scientific interest the knowledge of the evolution of phase transformation and residual stress from different levels and rates of plastic deformation imposed to the material. It is also important to evaluate the interference of metallographic preparation in quantitative analyzes of this steel. The main techniques used in this study consisted of X-rays diffraction and Ferritoscopy for the quantitation phase, and XRD to residual stress analysis also. As observed, the phase transformation quantification has not suffered significant influence of the metallographic preparation and evolved from increments of plastic deformation due to different stop charges and strain rates, leading to a further strengthening of the austenite matrix. The evaluation of residual stress resulting from the martensitic transformation was susceptible to the metallographic preparation and increased its value on comparison to sample without metallographic preparation. It was also observed that the residual stress decreased with the increase of the fraction of transformed martensite. (author)

Analysis of martensitic transformation and residual tension in an 304L stainless steel

International Nuclear Information System (INIS)

Alves, Juciane Maria

2014-01-01

The relationship between plastic deformation and the strain induced phase transformation, that provides a practical route to the development of new engineering materials with excellent mechanical properties, characterize the TRIP effect 'Transformation Induced Plasticity'. Among the stainless steels, the metastable 304 L austenitic steel is susceptible to transformation of austenite-martensite phase from tensile tests at room temperature by increments of plastic deformation. It is of great technological and scientific interest the knowledge of the evolution of phase transformation and residual stress from different levels and rates of plastic deformation imposed to the material. It is also important to evaluate the interference of metallographic preparation in quantitative analyzes of this steel. The main techniques used in this study consisted of X-rays diffraction and Ferritoscopy for the quantitation phase, and XRD to residual stress analysis also. As observed, the phase transformation quantification has not suffered significant influence of the metallographic preparation and evolved from increments of plastic deformation due to different stop charges and strain rates, leading to a further strengthening of the austenite matrix. The evaluation of residual stress resulting from the martensitic transformation was susceptible to the metallographic preparation and increased its value on comparison to sample without metallographic preparation. It was also observed that the residual stress decreased with the increase of the fraction of transformed martensite. (author)

Synthesis and characterization of actinide metal compounds formed by combustion

International Nuclear Information System (INIS)

Behrens, R.G.; King, M.A.

1985-01-01

This paper briefly describes the results of attempts to synthesize arsenides, phosphides, and antimonides of uranium and thorium using Self-Propagating High-Temperature Synthesis (SHS) techniques. This paper first summarizes the chemistry and thermodynamics of these chemical systems, describes SHS synthesis techniques, and then describes the results of the syntheses using data from powder x-ray diffraction, metallographic, and electron microprobe analyses

Development of Rolling Schedules for Equal Channel Angular Extrusion (ECAE)-Processed AZ31 Magnesium Alloy

Science.gov (United States)

2016-04-01

specimens were mounted in an epoxy resin and prepared using conventional metallographic techniques. A final etching, using diluted picric acid, was...additional pass, the shearing texture is exaggerated and, unless reversed , an acicular texture in the material could result. The function of route C

Microbiologically induced corrosion of carbon steel under continuous flow conditions

International Nuclear Information System (INIS)

Tunaru, Mariana; Dragomir, Maria; Voicu, Anca

2008-01-01

Microbiologically induced corrosion is the label generally applied to corrosion involving the action of bacteria on metal surfaces. While different combinations of bacterial species, materials and chemical constituents are interrelated factors, stagnant water is the factor most often mentioned in reported cases. This paper presents the results obtained regarding the testing of microbiologically induced corrosion of carbon steel under continuous flow conditions in the presence of iron-oxidizing bacteria. The tests were performed on coupons of SA106gr.B exposed both in stagnant conditions and in flow conditions. The surfaces of these coupons were studied by metallographic technique, while the developed biofilms were analysed using microbiological technique. The correlation of all the results which were obtained emphasized that the minimizing the occurrence of stagnant or low-flow conditions can prove effective in reducing the risk of microbiologically induced corrosion in plant cooling-water systems. (authors)

Analysis of rocks involving the x-ray diffraction, infrared and thermal gravimetric techniques

International Nuclear Information System (INIS)

Ikram, M.; Rauf, M.A.; Munir, N.

1998-01-01

Chemical analysis of rocks and minerals are usually obtained by a number of analytical techniques. The purpose of present work is to investigate the chemical composition of the rock samples and also to find that how far the results obtained by different instrumental methods are closely related. Chemical tests wee performed before using the instrumental techniques in order to determined the nature of these rocks. The chemical analysis indicated mainly the presence of carbonate and hence the carbonate nature of these rocks. The x-ray diffraction, infrared spectroscopy and thermal gravimetric analysis techniques were used for the determination of chemical composition of these samples. The results obtained by using these techniques have shown a great deal of similarities. (author)

Inspection of nuclear power plant piping welds by in-process acoustic emission monitoring

International Nuclear Information System (INIS)

Prine, D.W.

1976-01-01

The results of using in-process acoustic emission monitoring on nuclear power plant piping welds are discussed. The technique was applied to good and intentionally flawed test welds as well as production welds, and the acoustic emission results are compared to standard NDT methods and selected metallographic cross-sections

Mapping Breakpoints of Complex Chromosome Rearrangements Involving a Partial Trisomy 15q23.1-q26.2 Revealed by Next Generation Sequencing and Conventional Techniques.

Directory of Open Access Journals (Sweden)

Qiong Pan

Full Text Available Complex chromosome rearrangements (CCRs, which are rather rare in the whole population, may be associated with aberrant phenotypes. Next-generation sequencing (NGS and conventional techniques, could be used to reveal specific CCRs for better genetic counseling. We report the CCRs of a girl and her mother, which were identified using a combination of NGS and conventional techniques including G-banding, fluorescence in situ hybridization (FISH and PCR. The girl demonstrated CCRs involving chromosomes 3 and 8, while the CCRs of her mother involved chromosomes 3, 5, 8, 11 and 15. HumanCytoSNP-12 Chip analysis identified a 35.4 Mb duplication on chromosome 15q21.3-q26.2 in the proband and a 1.6 Mb microdeletion at chromosome 15q21.3 in her mother. The proband inherited the rearranged chromosomes 3 and 8 from her mother, and the duplicated region on chromosome 15 of the proband was inherited from the mother. Approximately one hundred genes were identified in the 15q21.3-q26.2 duplicated region of the proband. In particular, TPM1, SMAD6, SMAD3, and HCN4 may be associated with her heart defects, and HEXA, KIF7, and IDH2 are responsible for her developmental and mental retardation. In addition, we suggest that a microdeletion on the 15q21.3 region of the mother, which involved TCF2, TCF12, ADMA10 and AQP9, might be associated with mental retardation. We delineate the precise structures of the derivative chromosomes, chromosome duplication origin and possible molecular mechanisms for aberrant phenotypes by combining NGS data with conventional techniques.

Invasive and noninvasive dental analgesia techniques.

Science.gov (United States)

Estafan, D J

1998-01-01

Although needle-administered local anesthesia has been an essential tool of modern dentistry, it has also been responsible for many patients' fears of dental visits. Several new techniques have recently evolved that may offer viable alternatives. Two of these operate via electronic mechanisms that interfere with pain signals, two others involve transmucosal modes of administration, and a fifth technique involves an intraosseous pathway for anesthesia administration. Each of these techniques has different indications for dental procedures, but none is intended to replace needle administration in dentistry. This overview highlights the salient features of these alternative dental anesthesia techniques.

On a Numerical and Graphical Technique for Evaluating some Models Involving Rational Expectations

DEFF Research Database (Denmark)

Johansen, Søren; Swensen, Anders Rygh

Campbell and Shiller (1987) proposed a graphical technique for the present value model which consists of plotting the spread and theoretical spread as calculated from the cointegrated vector autoregressive model. We extend these techniques to a number of rational expectation models and give...

On a numerical and graphical technique for evaluating some models involving rational expectations

DEFF Research Database (Denmark)

Johansen, Søren; Swensen, Anders Rygh

Campbell and Shiller (1987) proposed a graphical technique for the present value model which consists of plotting the spread and theoretical spread as calculated from the cointegrated vector autoregressive model. We extend these techniques to a number of rational expectation models and give...

Determining partial differential cross sections for low-energy electron photodetachment involving conical intersections using the solution of a Lippmann-Schwinger equation constructed with standard electronic structure techniques.

Science.gov (United States)

Han, Seungsuk; Yarkony, David R

2011-05-07

A method for obtaining partial differential cross sections for low energy electron photodetachment in which the electronic states of the residual molecule are strongly coupled by conical intersections is reported. The method is based on the iterative solution to a Lippmann-Schwinger equation, using a zeroth order Hamiltonian consisting of the bound nonadiabatically coupled residual molecule and a free electron. The solution to the Lippmann-Schwinger equation involves only standard electronic structure techniques and a standard three-dimensional free particle Green's function quadrature for which fast techniques exist. The transition dipole moment for electron photodetachment, is a sum of matrix elements each involving one nonorthogonal orbital obtained from the solution to the Lippmann-Schwinger equation. An expression for the electron photodetachment transition dipole matrix element in terms of Dyson orbitals, which does not make the usual orthogonality assumptions, is derived.

Chromatic changes to artificial irises produced using different techniques

Science.gov (United States)

Bannwart, Lisiane Cristina; Goiato, Marcelo Coelho; dos Santos, Daniela Micheline; Moreno, Amália; Pesqueira, Aldiéris Alves; Haddad, Marcela Filié; Andreotti, Agda Marobo; de Medeiros, Rodrigo Antonio

2013-05-01

Ocular prostheses are important determinants of their users' aesthetic recovery and self-esteem. Because of use, ocular prostheses longevity is strongly affected by instability of the iris color due to polymerization. The goal of this study is to examine how the color of the artificial iris button is affected by different techniques of artificial wear and by the application of varnish following polymerization of the colorless acrylic resin that covers the colored paint. We produce 60 samples (n=10) according to the wear technique applied: conventional technique without varnish (PE); conventional technique with varnish (PEV); technique involving a prefabricated cap without varnish (CA); technique involving a prefabricated cap with varnish (CAV); technique involving inverted painting without varnish (PI); and technique involving inverted painting with varnish (PIV). Color readings using a spectrophotometer are taken before and after polymerization. We submitted the data obtained to analyses of variance and Tukey's test (P<0.05). The color test shows significant changes after polymerization in all groups. The PE and PI techniques have clinically acceptable values of ΔE, independent of whether we apply varnish to protect the paint. The PI technique produces the least color change, whereas the PE and CA techniques significantly improve color stability.

Creating Learning at Conferences Through Participant Involvement

DEFF Research Database (Denmark)

Ravn, Ib; Elsborg, Steen

as a forum for learning, mutual inspiration and "human co-flourishing." We offer five design principles that specify how conferences may involve participants more and hence increase their learning. In the research and development effort reported here, our team collaborated with conference organizers......The typical conference is brimming with PowerPoint presentations that leave very little time for participant involvement. Students of learning have long abandoned the transfer model that underlies this massive show of one-way communication. We propose an alternative theory of the conference...... in Denmark to introduce a variety of simple learning techniques related to the design principles at thirty real conferences of some 100-200 participants each. We present twelve of these techniques and the data evaluating them and conclude that by spending a fraction of the time at a conference on involving...

Characterization of ancient Indian iron and entrapped slag ...

Indian Academy of Sciences (India)

Unknown

scotch tape and the final sample was carbon coated by sputtering. In this way, the thin film could be observed in the OM and SEM. Specific localized regions of interest were then investigated by X-ray microdiffraction. 2.2 Techniques. The metallographically polished section and the thin film were both examined by optical ...

Influence of Ar-ion implantation on the structural and mechanical properties of zirconia as studied by Raman spectroscopy and nanoindentation techniques

Science.gov (United States)

Kurpaska, L.; Jasinski, J.; Wyszkowska, E.; Nowakowska-Langier, K.; Sitarz, M.

2018-04-01

In this study, structural and nanomechanical properties of zirconia polymorphs induced by ion irradiation were investigated by means of Raman spectroscopy and nanoindentation techniques. The zirconia layer have been produced by high temperature oxidation of pure zirconium at 600 °C for 5 h at normal atmospheric pressure. In order to distinguish between the internal and external parts of zirconia, the spherical metallographic sections have been prepared. The samples were irradiated at room temperature with 150 keV Ar+ ions at fluences ranging from 1 × 1015 to 1 × 1017 ions/cm2. The main objective of this study was to distinguish and confirm different structural and mechanical properties between the interface layer and fully developed scale in the internal/external part of the oxide. Conducted studies suggest that increasing ion fluence impacts Raman bands positions (especially characteristic for tetragonal phase) and increases the nanohardness and Young's modulus of individual phases. This phenomenon has been examined from the point of view of stress-induced hardening effect and classical monoclinic → tetragonal (m → t) martensitic phase transformation.

How can stakeholder involvement be improved?

International Nuclear Information System (INIS)

2015-12-01

Radioactive waste management is embedded in broader societal issues such as environment, risk management, sustainability, energy and health policy. In all these fields, there is an increasing demand for public involvement, participation or engagement. Guidance for public authorities also generally encourages greater involvement of the public. Involvement may take different forms at different phases and can include sharing information, consulting, dialoguing or deliberating on decisions with relevant stakeholders. Stakeholder involvement should be seen as a meaningful part of formulating and implementing public policy. There is no single technique for organising engagement. Initiatives should respond to their context and to stakeholders' particular needs. As the number of stakeholder involvement approaches and publications describing them continues to grow, new opportunities are opening up through social media, which has become an important tool for stakeholder involvement in recent years

Technique applied in the evaluation of the UFCC reactor at Refinaria Alberto Pasqualini (REFAP), PETROBRAS; Tecnicas utilizadas na avaliacao do reator da UFCC da REFAP

Energy Technology Data Exchange (ETDEWEB)

Cascaes, Ronesio da Silva [PETROBRAS (Brazil) Refinaria Alberto Pasqualini

1994-01-01

Main problems found in the maintenance of the Fluidized Catalytic Cracking (FCC) unity, searches of metal alteration properties, metallographic evaluations, failures and micro-structures alterations are presented. Micrographic analysis of the structural samples, the methodology to detect the failures and physical and chemical essays utilized in the inspection are also reported 13 refs., 64 figs., 1 tab.

Biopsy techniques for intraocular tumors

Directory of Open Access Journals (Sweden)

Pukhraj Rishi

2016-01-01

Full Text Available Biopsy involves the surgical removal of a tissue specimen for histopathologic evaluation. Most intraocular tumors are reliably diagnosed based on the clinical evaluation or with noninvasive diagnostic techniques. However, accurately diagnosing a small percentage of tumors can be challenging. A tissue biopsy is thus needed to establish a definitive diagnosis and plan the requisite treatment. From fine-needle aspiration biopsy (FNAB to surgical excision, all tissue collection techniques have been studied in the literature. Each technique has its indications and limitations. FNAB has been reported to provide for 88-95% reliable and safe ophthalmic tumor diagnosis and has gained popularity for prognostic purposes and providing eye conserving treatment surgeries. The technique and instrumentation for biopsy vary depending upon the tissue involved (retina, choroid, subretinal space, vitreous, and aqueous, suspected diagnosis, size, location, associated retinal detachment, and clarity of the media. The cytopathologist confers a very important role in diagnosis and their assistance plays a key role in managing and planning the treatment for malignancies.

Submucosal tunneling techniques: current perspectives.

Science.gov (United States)

Kobara, Hideki; Mori, Hirohito; Rafiq, Kazi; Fujihara, Shintaro; Nishiyama, Noriko; Ayaki, Maki; Yachida, Tatsuo; Matsunaga, Tae; Tani, Johji; Miyoshi, Hisaaki; Yoneyama, Hirohito; Morishita, Asahiro; Oryu, Makoto; Iwama, Hisakazu; Masaki, Tsutomu

2014-01-01

Advances in endoscopic submucosal dissection include a submucosal tunneling technique, involving the introduction of tunnels into the submucosa. These tunnels permit safer offset entry into the peritoneal cavity for natural orifice transluminal endoscopic surgery. Technical advantages include the visual identification of the layers of the gut, blood vessels, and subepithelial tumors. The creation of a mucosal flap that minimizes air and fluid leakage into the extraluminal cavity can enhance the safety and efficacy of surgery. This submucosal tunneling technique was adapted for esophageal myotomy, culminating in its application to patients with achalasia. This method, known as per oral endoscopic myotomy, has opened up the new discipline of submucosal endoscopic surgery. Other clinical applications of the submucosal tunneling technique include its use in the removal of gastrointestinal subepithelial tumors and endomicroscopy for the diagnosis of functional and motility disorders. This review suggests that the submucosal tunneling technique, involving a mucosal safety flap, can have potential values for future endoscopic developments.

Ultrasonic and metallographic studies on AISI 4140 steel exposed to hydrogen at high pressure and temperature

Science.gov (United States)

Oruganti, Malavika

This thesis conducts an investigation to study the effects of hydrogen exposure at high temperature and pressure on the behavior of AISI 4140 steel. Piezoelectric ultrasonic technique was primarily used to evaluate surface longitudinal wave velocity and defect geometry variations, as related to time after exposure to hydrogen at high temperature and pressure. Critically refracted longitudinal wave technique was used for the former and pulse-echo technique for the latter. Optical microscopy and scanning electron microscopy were used to correlate the ultrasonic results with the microstructure of the steel and to provide better insight into the steel behavior. The results of the investigation indicate that frequency analysis of the defect echo, determined using the pulse-echo technique at regular intervals of time, appears to be a promising tool for monitoring defect growth induced by a high temperature and high pressure hydrogen-related attack.

Radioimmunoassay and other related techniques

International Nuclear Information System (INIS)

Zarkawi, Moutaz

1993-04-01

The article reviews principles, requirements and reliability criteria of radioimmunoassay (RIA). Since basic reactions involved in RIA and related techniques are derived from reactions which take place in the immune system (IS) of humans and animals, the IS and the way it works will be described. In addition to RIA which involves the use of isotopes as tracers (labels), other non-radioisotopic and recent immunoassay techniques i.e. enzyme-linked immunosorbent assay (ELISA), chemiluminescence immunoassay (CLIA) and fluoroimmunoassay (FIA) will be dealt with. Some important and related terms will be defined and explained. (author). 59 refs., 4 figs

NDT: Replication avoids unnecessary replacement of power plant components

International Nuclear Information System (INIS)

Neubauer, B.; Wedel, U.

1984-01-01

Effective fracture prevention for components operating at high temperatures can be achieved without sacrificing useful life. This is done by nondestructive-metallographic examination at crack-susceptible locations of the components. Creep microcracks approximately one micron in size can be detected. RWTUV experience shows that, in general, the components need not be replaced or repaired until these microcracks have grown to form small creep macrocracks. The long prewarning period before macrocracks form provides assurance of safe operation for the full useful life of the components tested. The economic benefit achieved is considerable. Replication techniques have been widely applied by the authors in operating power plants since 1977. This nondestructive-evaluation method involves polishing small areas of selected piping-system components, preparing replicas of the polished areas, and examining the replicas under microscope for evidence of cavities, microcracks, or macrocracks

Next generation initiation techniques

Science.gov (United States)

Warner, Tom; Derber, John; Zupanski, Milija; Cohn, Steve; Verlinde, Hans

1993-01-01

Four-dimensional data assimilation strategies can generally be classified as either current or next generation, depending upon whether they are used operationally or not. Current-generation data-assimilation techniques are those that are presently used routinely in operational-forecasting or research applications. They can be classified into the following categories: intermittent assimilation, Newtonian relaxation, and physical initialization. It should be noted that these techniques are the subject of continued research, and their improvement will parallel the development of next generation techniques described by the other speakers. Next generation assimilation techniques are those that are under development but are not yet used operationally. Most of these procedures are derived from control theory or variational methods and primarily represent continuous assimilation approaches, in which the data and model dynamics are 'fitted' to each other in an optimal way. Another 'next generation' category is the initialization of convective-scale models. Intermittent assimilation systems use an objective analysis to combine all observations within a time window that is centered on the analysis time. Continuous first-generation assimilation systems are usually based on the Newtonian-relaxation or 'nudging' techniques. Physical initialization procedures generally involve the use of standard or nonstandard data to force some physical process in the model during an assimilation period. Under the topic of next-generation assimilation techniques, variational approaches are currently being actively developed. Variational approaches seek to minimize a cost or penalty function which measures a model's fit to observations, background fields and other imposed constraints. Alternatively, the Kalman filter technique, which is also under investigation as a data assimilation procedure for numerical weather prediction, can yield acceptable initial conditions for mesoscale models. The

Airway Clearance Techniques (ACTs)

Medline Plus

Full Text Available ... ACTs involve coughing or huffing . Many of them use percussion (clapping) or vibration to loosen mucus from airway walls. See how different airway clearance techniques work to help you clear the thick, sticky mucus ...

Short frontal plane fractures involving the dorsoproximal articular surface of the proximal phalanx: Description of the injury and a technique for repair.

Science.gov (United States)

Wright, I M; Minshall, G J

2018-01-01

Chip fractures of the dorsoproximal articular margin of the proximal phalanx are common injuries in racehorses. Large fractures can extend distal to the joint capsule insertion and have been described as dorsal frontal fractures. To report the location and morphology of short frontal plane fractures involving the dorsoproximal articular surface of the proximal phalanx and describe a technique for repair under arthroscopic and radiographic guidance. Single centre retrospective case study. Case records of horses with frontal plane fractures restricted to the dorsoproximal epiphysis and metaphysis of the proximal phalanx referred to Newmarket Equine Hospital were retrieved, images reviewed and lesion morphology described. A technique for repair and the results obtained are reported. A total of 22 fractures in 21 horses commencing at the proximal articular surface exited the dorsal cortex of the proximal phalanx distal to the metacarpophalangeal/metatarsophalangeal joint capsule in 17 hind- and five forelimbs. All were in Thoroughbred racehorses. In 16 cases these were acute racing or training injuries; 20 fractures were medial, one lateral and one was midline. All were repaired with a single lag screw using arthroscopic and radiographically determined landmarks. A total of 16 horses raced after surgery with performance data similar to their preinjury levels. The study demonstrates substantial morphological similarities between individual lesions supporting a common pathophysiology, but does not identify precise causation. There are no cases managed differently that might permit assessment of the comparative efficacy of the treatment described. Short frontal plane fractures involving the dorsoproximal margin of the proximal phalanx that exit the bone distal to the metacarpophalangeal/metatarsophalangeal joint capsule have substantial morphological similarities, are amenable to minimally invasive repair and carry a good prognosis for return to training and racing. �

Algorithm based on regional separation for automatic grain boundary extraction using improved mean shift method

Science.gov (United States)

Zhenying, Xu; Jiandong, Zhu; Qi, Zhang; Yamba, Philip

2018-06-01

Metallographic microscopy shows that the vast majority of metal materials are composed of many small grains; the grain size of a metal is important for determining the tensile strength, toughness, plasticity, and other mechanical properties. In order to quantitatively evaluate grain size in metals, grain boundaries must be identified in metallographic images. Based on the phenomenon of grain boundary blurring or disconnection in metallographic images, this study develops an algorithm based on regional separation for automatically extracting grain boundaries by an improved mean shift method. Experimental observation shows that the grain boundaries obtained by the proposed algorithm are highly complete and accurate. This research has practical value because the proposed algorithm is suitable for grain boundary extraction from most metallographic images.

Metallurgical failure analysis for a blade failed in a gas-turbine engine of a power plant

International Nuclear Information System (INIS)

Huda, Zainul

2009-01-01

The failed gas-turbine blades (first stage blades) (type Siemens V94.2 KWU) were acquired from TNB Research Sdn. Bhd: a subsidiary of Malaysian power-generation industry (TNB, Malaysia). The blades were sectioned for metallographic investigations. The microstructural characterization involved use of both optical as well as electron microscopes including application of EPMA technique. The Microstructures were compared for three spots selection i.e. leading edge of the blade (transverse and longitudinal), trailing edge of the blade (transverse and longitudinal), and centre (near the platform of the blade) (transverse and longitudinal). The material properties and behavior at high temperature were interpreted on the basis of the observed microstructures and the phases present in the alloy. The interpretations were related to the operating conditions of the turbine blade; and main cause of failure was found to be creep damage. Recommendations have been made for improved material performance.

A simplified indirect bonding technique

Directory of Open Access Journals (Sweden)

Radha Katiyar

2014-01-01

Full Text Available With the advent of lingual orthodontics, indirect bonding technique has become an integral part of practice. It involves placement of brackets initially on the models and then their transfer to teeth with the help of transfer trays. Problems encountered with current indirect bonding techniques used are (1 the possibility of adhesive flash remaining around the base of the brackets which requires removal (2 longer time required for the adhesive to gain enough bond strength for secure tray removal. The new simplified indirect bonding technique presented here overcomes both these problems.

Craniospinal irradiation techniques

Energy Technology Data Exchange (ETDEWEB)

Scarlatescu, Ioana, E-mail: scarlatescuioana@gmail.com; Avram, Calin N. [Faculty of Physics, West University of Timisoara, Bd. V. Parvan 4, 300223 Timisoara (Romania); Virag, Vasile [County Hospital “Gavril Curteanu” - Oradea (Romania)

2015-12-07

In this paper we present one treatment plan for irradiation cases which involve a complex technique with multiple beams, using the 3D conformational technique. As the main purpose of radiotherapy is to administrate a precise dose into the tumor volume and protect as much as possible all the healthy tissues around it, for a case diagnosed with a primitive neuro ectoderm tumor, we have developed a new treatment plan, by controlling one of the two adjacent fields used at spinal field, in a way that avoids the fields superposition. Therefore, the risk of overdose is reduced by eliminating the field divergence.

Neutron techniques in Safeguards

International Nuclear Information System (INIS)

Zucker, M.S.

1982-01-01

An essential part of Safeguards is the ability to quantitatively and nondestructively assay those materials with special neutron-interactive properties involved in nuclear industrial or military technology. Neutron techniques have furnished most of the important ways of assaying such materials, which is no surprise since the neutronic properties are what characterizes them. The techniques employed rely on a wide selection of the many methods of neutron generation, detection, and data analysis that have been developed for neutron physics and nuclear science in general

Ultrasonic inspection of austenitic welds

International Nuclear Information System (INIS)

Baikie, B.L.; Wagg, A.R.; Whittle, M.J.; Yapp, D.

1976-01-01

Optical and X-ray metallography combined with ultrasonic testing by compression waves was used for inspection of stainless steel weld metal produced by three different welding techniques. X-ray diffraction showed that each weld possessed a characteristic fibre textured structure which was shown by optical microscopy to be parallel to columnar grain boundaries. Metallographic evidence suggested that the development of fibre texture is due to the mechanism of competitive growth. From observations made as a result of optical metallographic examination the orientation of the fibre axis could be predicted if the weld geometry and welding procedure were known. Ultrasonic velocity and attenuation measurements as a continuous function of grain orientation, made on cylinders machined from weld samples, showed that attenuation was strongly orientation dependent. It was concluded that the sensitivity of ultrasonic inspection to small defects is unlikely to be as high for austenitic welds as for ferritic even when transmission is improved by modifying the welding procedure to improve the ultrasonic transmission. (U.K.)

Effect of Heating Time on Hardness Properties of Laser Clad Gray Cast Iron Surface

Science.gov (United States)

Norhafzan, B.; Aqida, S. N.; Mifthal, F.; Zulhishamuddin, A. R.; Ismail, I.

2018-03-01

This paper presents effect of heating time on cladded gray cast iron. In this study, the effect of heating time on cladded gray cast iron and melted gray cast iron were analysed. The gray cast iron sample were added with mixed Mo-Cr powder using laser cladding technique. The mixed Mo and Cr powder was pre-placed on gray cast iron surface. Modified layer were sectioned using diamond blade cutter and polish using SiC abrasive paper before heated. Sample was heated in furnace for 15, 30 and 45 minutes at 650 °C and cool down in room temperature. Metallographic study was conduct using inverted microscope while surface hardness properties were tested using Wilson hardness test with Vickers scale. Results for metallographic study showed graphite flakes within matrix of pearlite. The surface hardness for modified layer decreased when increased heating time process. These findings are significant to structure stability of laser cladded gray cast iron with different heating times.

Real-time image fusion involving diagnostic ultrasound

DEFF Research Database (Denmark)

Ewertsen, Caroline; Săftoiu, Adrian; Gruionu, Lucian G

2013-01-01

The aim of our article is to give an overview of the current and future possibilities of real-time image fusion involving ultrasound. We present a review of the existing English-language peer-reviewed literature assessing this technique, which covers technical solutions (for ultrasound...

Review of procedures involving separation and preconcentration for the determination of cadmium using spectrometric techniques

International Nuclear Information System (INIS)

Ferreira, Sergio L.C.; Andrade, Jailson B. de; Korn, Maria das Gracas A.; Pereira, Madson de G.; Lemos, Valfredo A.; Santos, Walter N.L. dos; Rodrigues, Frederico de Medeiros; Souza, Anderson S.; Ferreira, Hadla S.; Silva, Erik G.P. da

2007-01-01

Spectrometric techniques for the analysis of trace cadmium have developed rapidly due to the increasing need for accurate measurements at extremely low levels of this element in diverse matrices. This review covers separation and preconcentration procedures, such as electrochemical deposition, precipitation, coprecipitation, solid phase extraction, liquid-liquid extraction (LLE) and cloud point extraction (CPE), and consider the features of the their application with several spectrometric techniques

Difference in temporal lobe dose between two radiotherapy techniques in the treatment of NPC with anterior nasal involvement

International Nuclear Information System (INIS)

Wu, V.W.C.; Luk, J.H.Y.; Wong, S.F.T.; Lam, E.C.H.; Fung, M.C.Y.; Tong, S.M.; Ku, I.K.M.

1997-01-01

Nasopharyngeal carcinoma with anterior extension are treated with special radiotherapy techniques. The purpose of this study is to investigate the difference of temporal lobe dose between two radiotherapy techniques (A and B) which are commonly used in the treatment of such condition in Hong Kong. The study is carried out by performing radiation treatments to a humanoid phantom under simulated conditions of the two techniques. The dose measurement is done by thermoluminescent dosimeters (TLD) which are placed inside the phantom. Both techniques employ a '3-field' arrangement: a heavy-weighted anterior facial fields with two lateral opposing facial fields. The main difference lies in the anterior facial field in which technique A uses electron beam throughout while technique B uses a mixture of photon and electron beams. The results demonstrates that technique A delivers higher dose to temporal lobe than technique B. In a course of radical external beam radiotherapy (66 Gy), the mean dose to inferior temporal lobe are 59.29 Gy in technique A and 34.06 Gy in technique B respectively (p < 0.0001). Furthermore, it is found that the temporal lobe dose difference between the two techniques is mainly due to their phase I treatment. (p < 0.0001 for phase I and p = 0.078 for phase II). (authors)

Difference in temporal lobe dose between two radiotherapy techniques in the treatment of NPC with anterior nasal involvement

Energy Technology Data Exchange (ETDEWEB)

Wu, V.W.C.; Luk, J.H.Y.; Wong, S.F.T.; Lam, E.C.H.; Fung, M.C.Y.; Tong, S.M.; Ku, I.K.M. [Hong Kong Polytechnic University, Hong Kong, (Hong Kong). Department of Radiography and Optometry

1997-04-01

Nasopharyngeal carcinoma with anterior extension are treated with special radiotherapy techniques. The purpose of this study is to investigate the difference of temporal lobe dose between two radiotherapy techniques (A and B) which are commonly used in the treatment of such condition in Hong Kong. The study is carried out by performing radiation treatments to a humanoid phantom under simulated conditions of the two techniques. The dose measurement is done by thermoluminescent dosimeters (TLD) which are placed inside the phantom. Both techniques employ a `3-field` arrangement: a heavy-weighted anterior facial fields with two lateral opposing facial fields. The main difference lies in the anterior facial field in which technique A uses electron beam throughout while technique B uses a mixture of photon and electron beams. The results demonstrates that technique A delivers higher dose to temporal lobe than technique B. In a course of radical external beam radiotherapy (66 Gy), the mean dose to inferior temporal lobe are 59.29 Gy in technique A and 34.06 Gy in technique B respectively (p < 0.0001). Furthermore, it is found that the temporal lobe dose difference between the two techniques is mainly due to their phase I treatment. (p < 0.0001 for phase I and p = 0.078 for phase II). (authors). 14 refs., 3 tabs., 6 figs.

Gastrointestinal involvement secondary to non-Hodgkins lymphoma in HIV+patients

International Nuclear Information System (INIS)

Bueno, P.; Hernandez. L.; Ruiz, P.; Fernandez, C.; Porto, C.

1996-01-01

We present the clinical and radiological findings in 12 HIV-positive patients with gastrointestinal involvement secondary to non-Hodgkin's lymphoma, focusing on the value of the different diagnostic techniques employed (barium studies, ultrasonography and CT) and the differential diagnosis in view of our findings in these patients. We have reviewed the case histories of 58 HIV-positive patients diagnosed as having non-Hodgkin's lymphoma focusing on the results of barium studies, ultrasonography and CT scanning. According to barium studies, ultrasonography and CT, 12 patients (21%) presented gastrointestinal involvement, located in stomach (n=3D5), duodenum (n=3D2), small bowel (n=3D4), mesentery (n=3D1) and perianal region ( n=3D1). Enlarged abdominal lymph nodes were detected in 10 patients (83%). Six patients (50%) presented extraintestinal lymphomatous involvement and four (30%) had extraabdominal involment. Barium studies and CT were useful in the detection of the lesions of all the patients in whom these techniques were performed. CT also allowed the assessment of extraintestinal involvement. Ultrasonography showed poor sensitivity in the study of gastrointestinal involvement, but was effective in the detection of adenophathy. (Author) 27 refs

RADIOMETRIC TECHNIQUES IN HEAVY MINERAL EXPLORATION AND EXPLOITATION

NARCIS (Netherlands)

DEMEIJER, RJ; TANCZOS, IC; STAPEL, C

1994-01-01

In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence

Metallographic assessment of Al-12Si high-pressure die casting escalator steps.

Science.gov (United States)

Vander Voort, George Frederic; Suárez-Peña, Beatriz; Asensio-Lozano, Juan

2014-10-01

A microstructural characterization study was performed on high-pressure die cast specimens extracted from escalator steps manufactured from an Al-12 wt.% Si alloy designed for structural applications. Black and white, color light optical imaging and scanning electron microscopy techniques were used to conduct the microstructural analysis. Most regions in the samples studied contained globular-rosette primary α-Al grains surrounded by an Al-Si eutectic aggregate, while primary dendritic α-Al grains were present in the surface layer. This dendritic microstructure was observed in the regions where the melt did not impinge directly on the die surface during cavity filling. Consequently, microstructures in the surface layer were nonuniform. Utilizing physical metallurgy principles, these results were analyzed in terms of the applied pressure and filling velocity during high-pressure die casting. The effects of these parameters on solidification at different locations of the casting are discussed.

Cu-Fe welding techniques by electromagnetic and electron beam welding processes

International Nuclear Information System (INIS)

Kumar, Satendra; Saroj, P.C.; Kulkarni, M.R.; Sharma, A.; Rajawat, R.K.; Saha, T.K.

2015-01-01

Electromagnetic welding being a solid state welding process has been found suitable for welding Copper and Iron which are conventionally very tricky. Owing to good electrical conductivity of both copper and iron, they are best suited combination for EM welding. For the experimental conditions presented above, 1.0 mm wall thickness of Cu tube was lap welded to Fe disc. A heavy duty four disc stainless steel coil was used for electromagnetic welding of samples. MSLD of the welded samples indicated leak proof joints. Metallographic examination of the welds also revealed defect free interfaces. Electron beam welding is also a non-conventional welding process used for joining dissimilar materials. Autogenous welding of the above specimen was carried out by EBW method for the sake of comparison. A characterization analysis of the above mentioned joining processes will be discussed in the paper. (author)

Biokinematic structure of techniques wrestlers during pre-basic training

OpenAIRE

S.V. Sinіgovets

2013-01-01

The theoretical aspects of freestyle wrestlers. Experimentally investigated the structural elements of techniques during pre-basic training. The study involved 28 young fighters. Held video computer analysis techniques. Identified biomechanical characteristics defined kinematic structure of the temporal and spatial-temporal characteristics of the basic techniques. Shown variability of the individual phases of the basic techniques. Structural dynamics of the resulting velocities of the individ...

Teacher Involvement in Adult Marketing Education: Impeding Factors and Enhancing Strategies.

Science.gov (United States)

Price, William T., Jr.

1988-01-01

Using the nominal group technique, 60 of the 323 high school marketing teachers in Virginia identified major factors impeding their involvement in adult marketing education as lack of time and demands of the job. Insufficient compensation for working with adults and lack of administrator support also inhibited teacher involvement in adult…

Surgical treatment of cavernous malformations involving medulla oblongata.

Science.gov (United States)

Zhang, Si; Lin, Sen; Hui, Xuhui; Li, Hao; You, Chao

2017-03-01

Surgical treatment of cavernous malformations (CMs) involving medulla oblongata is more difficult than the CMs in other sites because of the surrounding vital structures. However, the distinctive features and treatment strategies have not been well illustrated. Therefore, we enrolled a total of 19 patients underwent surgical treatment of CMs involving medulla oblongata in our hospital from August 2008 to August 2014. The clinical features, surgical management and clinical outcome of these patients were retrospectively analyzed, while our institutional surgical indications, approaches and microsurgical techniques were discussed. In our study, gross total resection was achieved in 17 patients and subtotal resection in 2. Two patients underwent emergency surgeries due to severe and progressive neurological deficits. The postoperative new-onset or worsened neurological deficits occurred in 6 patients. After a mean follow-up of 45.8±22.2months, the neurological status was improved in 10 patients and remained stable in 7. The mean modified Rankin Scale (mRS) was 2.58±1.26 preoperatively, 3.11±0.99 postoperatively and 1.84±1.42 at the recent follow-up, respectively. During the follow-up period, no rehemorrhage and recurrence occurred, and the residual lesions remained stable. We recommended surgical resection of symptomatic CMs involving medulla oblongata via optimal approaches, feasible entry zones and meticulous microsurgical techniques in attempting to achieve safe resection and favorable outcome. The clinical features, surgical indications, timing and microsurgical techniques of this special entity should be distinctive from the brainstem cavernous malformations in other sites. Copyright © 2016 Elsevier Ltd. All rights reserved.

Final report on: Grain size determination in zirconium alloys (IAEA Research Contract No. 6025/Rb.)

International Nuclear Information System (INIS)

Martinez M, E.

1991-12-01

In spite of the amount of research developed the knowledge still is far from complete and in this basis the International Atomic Energy Agency, (IAEA), by means of the Working Group on Water Reactor Fuel Performance and Technology, initiated, in 1990 the Coordinated Research Programme named Grain Size Determination In Zirconium Alloys. Several countries were invited to participate and to contribute to the main objective of the programme, which can be state as: To develop a unified metallographic technique capable to show the microstructure of zircaloy in a reproducible and uniform manner. To fulfill the objective the following goals were established: A. To measure the grain size and perform an statistical treatment, in samples prepared specifically to show different amounts of cold work, recrystallization and grain growth. B. To compare the results obtained by the different laboratories involved in the programme. C. Finally, after the Ugine meeting, also the determination of the recrystallization and grain growth kinetics. (Author)

Metallography of powder metallurgy materials

International Nuclear Information System (INIS)

Lawley, Alan; Murphy, Thomas F.

2003-01-01

The primary distinction between the microstructure of an ingot metallurgy/wrought material and one fabricated by the powder metallurgy route of pressing followed by sintering is the presence of porosity in the latter. In its various morphologies, porosity affects the mechanical, physical, chemical, electrical and thermal properties of the material. Thus, it is important to be able to characterize quantitatively the microstructure of powder metallurgy parts and components. Metallographic procedures necessary for the reliable characterization of microstructures in powder metallurgy materials are reviewed, with emphasis on the intrinsic challenges presented by the presence of porosity. To illustrate the utility of these techniques, five case studies are presented involving powder metallurgy materials. These case studies demonstrate problem solving via metallography in diverse situations: failure of a tungsten carbide-coated precipitation hardening stainless steel, failure of a steel pump gear, quantification of the degree of sinter (DOS), simulation of performance of a porous filter using automated image analysis, and analysis of failure in a sinter brazed part assembly

Estimation of Correlation Functions by the Random Decrement Technique

DEFF Research Database (Denmark)

Brincker, Rune; Krenk, Steen; Jensen, Jakob Laigaard

responses simulated by two SDOF ARMA models loaded by the same bandlimited white noise. The speed and the accuracy of the RDD technique is compared to the Fast Fourier Transform (FFT) technique. The RDD technique does not involve multiplications, but only additions. Therefore, the technique is very fast......The Random Decrement (RDD) Technique is a versatile technique for characterization of random signals in the time domain. In this paper a short review of the theoretical basis is given, and the technique is illustrated by estimating auto-correlation functions and cross-correlation functions on modal...

Estimation of Correlation Functions by the Random Decrement Technique

DEFF Research Database (Denmark)

Brincker, Rune; Krenk, Steen; Jensen, Jacob Laigaard

1991-01-01

responses simulated by two SDOF ARMA models loaded by the same band-limited white noise. The speed and the accuracy of the RDD technique is compared to the Fast Fourier Transform (FFT) technique. The RDD technique does not involve multiplications, but only additions. Therefore, the technique is very fast......The Random Decrement (RDD) Technique is a versatile technique for characterization of random signals in the time domain. In this paper a short review of the theoretical basis is given, and the technique is illustrated by estimating auto-correlation functions and cross-correlation functions on modal...

Estimation of Correlation Functions by the Random Decrement Technique

DEFF Research Database (Denmark)

Brincker, Rune; Krenk, Steen; Jensen, Jakob Laigaard

1992-01-01

responses simulated by two SDOF ARMA models loaded by the same bandlimited white noise. The speed and the accuracy of the RDD technique is compared to the Fast Fourier Transform (FFT) technique. The RDD technique does not involve multiplications, but only additions. Therefore, the technique is very fast......The Random Decrement (RDD) Technique is a versatile technique for characterization of random signals in the time domain. In this paper a short review of the theoretical basis is given, and the technique is illustrated by estimating auto-correlation functions and cross-correlation functions on modal...

Feasibility of new breeding techniques for organic farming

DEFF Research Database (Denmark)

Andersen, Martin Marchman; Landes, Xavier; Xiang, Wen

2015-01-01

of new breeding techniques (NBTs) for rewilding, a process involving the reintroduction of properties from the wild relatives of crops, as a method to close the productivity gap. The most efficient methods of rewilding are based on modern biotechnology techniques, which have yet to be embraced...

Immunoperoxidase technique in experimental chronic chagasic myocarditis

Directory of Open Access Journals (Sweden)

M.d. Maria Celina Morales

1987-04-01

Full Text Available Chagas'disease has been described as the commonest form of chronic myocarditis. An immunologic pathogenesis has been discribed for this form of the disease. So far, no immunoperoxidase technique has been used for the detection of immunological deposits in chronic experimental Chagas'myocardiopathy. Forty-one Swiss mice, three months old were inoculated intraperitoneally with doses between 10 and 10(5 Tulahuen trypomastigotes. Mice were reinoculated one month after with doses between 10² and 10(5 and sacrificed at 6 (n=21 and 9 months (n=9 after the first inoculation. ECGs were recorded before sacrifice. Immunoperoxidase technique (peroxidase-antiperoxidase method, immunofluorescence (direct and indirect as well as histological studies were performed in myocardiums and skeletal muscles of the surviving animals. The most sensitive methods for detecting chronic chagasic infection were the routine histologic studies (73% and the ECGs 83% and 89% on 6 and 9 mo. post-infected mice, respectively. Myocardial involvement varied from interstitial mild focal lymphocyte infiltrates up to replacement of myocytes by loose connective tissue. Atrial myocardiums (21/23, 91% were more affected than ventricles (9/23, 39%. Typical chagasic nests were rarely found. Skeletal muscle involvement (11/18 and 7/9 varied from mild to extensive lymphocyte and plasmacell infiltrates, and necrotic fibers. The involved antigen were shown in skeletal muscles by the immunoperoxidase technique as diffusely arranged granular intracytoplasmatic deposit for both IgC and total immunoglobulins. The coincidence between this technique and histologic muscle lesions was 11/18 (61(% in 6 mo. and 6/8 (75% at 9 mo. post-infection. In heart, delicate granular deposits of total immunoglobulins were seen diffusely arranged within the ventricular myocytes; coincidence between immunoperoxidase technique anl histologic involvement increased from 36 to 66% in animals sacrifeced 6 and 9 mo. post

Pure transvaginal excision of mesh erosion involving the bladder.

Science.gov (United States)

Firoozi, Farzeen; Goldman, Howard B

2013-06-01

We present a pure transvaginal approach to the removal of eroded mesh involving the bladder secondary to placement of transvaginal mesh for management of pelvic organ prolapse (POP) using a mesh kit. Although technically challenging, we demonstrate the feasibility of a purely transvaginal approach, avoiding a potentially more morbid transabdominal approach. The video presents the surgical technique of pure transvaginal excision of mesh erosion involving the bladder after mesh placement using a prolapse kit was performed. This video shows that purely transvaginal removal of mesh erosion involving the bladder can be done safely and is feasible.

Waste reduction efforts through the evaluation and procurement of a digital camera system for the Alpha-Gamma Hot Cell Facility at Argonne National Laboratory-East

International Nuclear Information System (INIS)

Bray, T. S.; Cohen, A. B.; Tsai, H.; Kettman, W. C.; Trychta, K.

1999-01-01

The Alpha-Gamma Hot Cell Facility (AGHCF) at Argonne National Laboratory-East is a research facility where sample examinations involve traditional photography. The AGHCF documents samples with photographs (both Polaroid self-developing and negative film). Wastes generated include developing chemicals. The AGHCF evaluated, procured, and installed a digital camera system for the Leitz metallograph to significantly reduce labor, supplies, and wastes associated with traditional photography with a return on investment of less than two years

Momentum--"Evaluating Your Marketing Program: Measuring and Tracking Techniques."

Science.gov (United States)

Meservey, Lynne D.

1990-01-01

Suggests 10 tracking techniques for evaluating marketing performance. Techniques involve utilization rate, inquiry and source of inquiry tracking, appointment and interview tracking, enrollment conversion, cost per inquiry and per enrollment, retention rate, survey results, and "mystery shopper." (RJC)

Retrograde Ascending Dissection After Thoracic Endovascular Aortic Repair Combined With the Chimney Technique and Successful Open Repair Using the Frozen Elephant Trunk Technique.

Science.gov (United States)

Hirano, Koji; Tokui, Toshiya; Nakamura, Bun; Inoue, Ryosai; Inagaki, Masahiro; Maze, Yasumi; Kato, Noriyuki

2018-01-01

The chimney technique can be combined with thoracic endovascular aortic repair (TEVAR) to both obtain an appropriate landing zone and maintain blood flow of the arch vessels. However, surgical repair becomes more complicated if retrograde type A aortic dissection occurs after TEVAR with the chimney technique. We herein report a case involving a 73-year-old woman who developed a retrograde ascending dissection 3 months after TEVAR for acute type B aortic dissection. To ensure an adequate proximal sealing distance, the proximal edge of the stent graft was located at the zone 2 level and an additional bare stent was placed at the left subclavian artery (the chimney technique) at the time of TEVAR. Enhanced computed tomography revealed an aortic dissection involving the ascending aorta and aortic arch. Surgical aortic repair using the frozen elephant trunk technique was urgently performed. The patient survived without stroke, paraplegia, renal failure, or other major complications. Retrograde ascending dissection can occur after TEVAR combined with the chimney technique. The frozen elephant trunk technique is useful for surgical repair in such complicated cases.

Telescopes and Techniques

CERN Document Server

Kitchin, C R

2013-01-01

Telescopes and Techniques has proved itself in its first two editions, having become probably one of the most widely used astronomy texts, both for amateur astronomers and astronomy and astrophysics undergraduates. Both earlier editions of the book were widely used for introductory practical astronomy courses in many universities. In this Third Edition the author guides the reader through the mathematics, physics and practical techniques needed to use today's telescopes (from the smaller models to the larger instruments installed in many colleges) and how to find objects in the sky. Most of the physics and engineering involved is described fully and requires little prior knowledge or experience. Both visual and electronic imaging techniques are covered, together with an introduction to how data (measurements) should be processed and analyzed. A simple introduction to radio telescopes is also included. Brief coverage of the more advanced topics of photometry and spectroscopy are included, but mainly to enable ...

Identification of microorganisms involved in nitrogen removal from wastewater treatment systems by means of molecular biology techniques

International Nuclear Information System (INIS)

Figueroa, M.; Alonso-Gutierrez, J.; Campos, J. L.; Mendez, R.; Mosquera-Corral, A.

2010-01-01

The identification of the main bacteria populations present in the granular biomass from a biological reactor treating wastewater has been performed by applying two different molecular biology techniques. By means of the DGGE technique five different genera of heterotrophic bacteria (Thiothrix, Thauera, Cloroflexi, Comamonas y Zoogloea) and one of ammonia oxidizing bacteria (Nitrosomanas) were identified. The FISH technique, based on microscopy, allowed the in situ visualization and quantification of those microorganisms. Special attention was paid to filamentous bacteria distribution (Thiothrix and Cloroflexi) which could exert a structural function in aerobic granular sludge. (Author) 26 refs.

A Study on Employee Retention Techniques

OpenAIRE

Savarimuthu, Dr. A; Hemalatha, N.

2013-01-01

The objective of perusing this study is to assess the level of satisfaction of employee retention techniques at GB Engineering Enterprises PVT Limited., Trichy.This study gains significance because of employee retention techniques can be approached from various angles. It is desirable state of existence involving retention strategies generally fall in to one of four categories salary, working conditions, job enrichment and education. These four elements together constitute. The structure of e...

Vacuum brazing techniques for irradiation devices at TRIGA research reactor

International Nuclear Information System (INIS)

Savu, M.; Valeca, S. C.; Amzoi, A.

2016-01-01

Metallic thin-walled thermocouples are required for monitoring the temperature value for experiments that are conducted in a nuclear research reactor. The different location wall crossing is made by instrumented passage. Such a passage produced by vacuum brazing using a BNi-7 alloy, represents the proper way to obtain a sealed joint, which can withstand corrosion and high temperatures, having in the same time a small neutron cross section. This paper presents the brazing experiments of K-type thermocouples with stainless steel and Inconel 600 sheath. The sheaths brittleness, hardness changing in joint.s vicinity and structural modification emphasized by metallographic analysis are aspects treated by comparing different samples obtained in brazing laboratory. For finding the correct answer regarding the attenuation of negative effects which are occurring during brazing procedure using Inconel 600 - BNi-7 combination, one can assess both the adopted solution used in designing instrumented passage and thermal regime parameters and its precisely control. (authors)

Radiation synthesized protein-based nanoparticles: A technique overview

International Nuclear Information System (INIS)

Varca, Gustavo H.C.; Perossi, Gabriela G.; Grasselli, Mariano; Lugão, Ademar B.

2014-01-01

Seeking for alternative routes for protein engineering a novel technique – radiation induced synthesis of protein nanoparticles – to achieve size controlled particles with preserved bioactivity has been recently reported. This work aimed to evaluate different process conditions to optimize and provide an overview of the technique using γ-irradiation. Papain was used as model protease and the samples were irradiated in a gamma cell irradiator in phosphate buffer (pH=7.0) containing ethanol (0–35%). The dose effect was evaluated by exposure to distinct γ-irradiation doses (2.5, 5, 7.5 and 10 kGy) and scale up experiments involving distinct protein concentrations (12.5–50 mg mL −1 ) were also performed. Characterization involved size monitoring using dynamic light scattering. Bityrosine detection was performed using fluorescence measurements in order to provide experimental evidence of the mechanism involved. Best dose effects were achieved at 10 kGy with regard to size and no relevant changes were observed as a function of papain concentration, highlighting very broad operational concentration range. Bityrosine changes were identified for the samples as a function of the process confirming that such linkages play an important role in the nanoparticle formation. - Highlights: • Synthesis of protein-based nanoparticles by γ-irradiation. • Optimization of the technique. • Overview of mechanism involved in the nanoparticle formation. • Engineered papain nanoparticles for biomedical applications

Characterization of oxidation resistance of stainless steels at high temperature by metallographic examinations and in-situ electrical resistance measurements; Charakterisierung der Oxidationsbestaendigkeit in nichtrostenden Staehlen bei hoher Temperatur durch Metallographische Untersuchungen und In-Situ-Messungen des elektrischen Widerstands

Energy Technology Data Exchange (ETDEWEB)

Bruncko, Mihael; Rudolf, Rebeka; Anzel, Ivan [Maribor Univ. (Slovenia). Faculty of Mechanical Engineering; Mehrabi, Kambiz [Pankl Drivetrain Systems GmbH und Co. KG, Kapfenberg (Austria); Kneissl, Albert C. [Leoben Univ. (Austria). Dept. of Physical Metallurgy and Materials Testing

2013-07-01

Practically all metals and alloys survive high-temperature exposure by growing oxide scales and/or by precipitation of the oxide particles in the matrix. Formed products can grow in shape of external oxide layers on surfaces, or as discrete oxide particles precipitated in a metal matrix. The first case represents external oxidation, and the other case is called internal oxidation. These processes are very important, because they determine the properties and applicability of metallic materials. Generally, they are undesired, because they cause deterioration of the mechanical properties and decomposition of metallic material. On the other side, the controlled process of external oxidation could be used for formation of protective coatings and the internal oxidation for dispersion strengthening of materials. In this paper we present monitoring of high-temperature oxidation of X12Cr13 stainless steel by in-situ electrical resistance measurements at different annealing temperatures in the air atmosphere. We determined the kinetics of oxide scale formation and its morphology with additional metallographic examination made by optical and scanning electron microscopy. The results of this research work show that in-situ monitoring and characterization of high-temperature oxidation present a strong tool that will contribute to a better fundamental understanding of the phenomena that occur during high-temperature oxidation of metallic materials. (orig.)

Interrelation of material microstructure, ultrasonic factors, and fracture toughness of two phase titanium alloy

Science.gov (United States)

Vary, A.; Hull, D. R.

1982-01-01

The pivotal role of an alpha-beta phase microstructure in governing fracture toughness in a titanium alloy, Ti-662, is demonstrated. The interrelation of microstructure and fracture toughness is demonstrated using ultrasonic measurement techniques originally developed for nondestructive evaluation and material property characterization. It is shown that the findings determined from ultrasonic measurements agree with conclusions based on metallurgical, metallographic, and fractographic observations concerning the importance of alpha-beta morphology in controlling fracture toughness in two phase titanium alloys.

Microstructure Of A SIC/(Ti/V/Cr/Sn/Al) Composite

Science.gov (United States)

Lerch, Bradley A.; Hull, David R.; Leonhardt, Todd A.

1990-01-01

NASA technical memorandum reports on analysis of composite material made of SiC fibers in matrix of 0.76 Ti/0.15 V/0.03 Cr/0.03 Sn/0.03 Al (parts by weight) alloy. Purposes of study to investigate suitability of some metallographic techniques for use on composite materials in general and to obtain information about macrostructure and microstructure of this specific composite to provide guidance for experimental and theoretical studies of more advanced composites.

Absolute calibration technique for spontaneous fission sources

International Nuclear Information System (INIS)

Zucker, M.S.; Karpf, E.

1984-01-01

An absolute calibration technique for a spontaneously fissioning nuclide (which involves no arbitrary parameters) allows unique determination of the detector efficiency for that nuclide, hence of the fission source strength

Manufacture of Damascus steel: Metallographic study

International Nuclear Information System (INIS)

Criado, A.J.; Martinez, J.A.; Calabres, R.; Arias, D.

1997-01-01

Damascus Steel is the denomination that the Europeans gave to the material with which the musulman swords were manufactured during the Era of the Crusades. This hypereutectoid steel presents a high content in carbon more than 0.8%, and in some cases up to 2% in weight. The secret of its good mechanical characteristics is based in the hot forging process in the temperatures interval between 650 and 850 degree centigree. The final quenching in water brine or other aqueous solutions, confers to the swords manufactured with this steel a good resistance to its cutting edge and a high toughness. In the present investigation, the manufacture processes of this type of steel are studied. Electronic scanning microscopy has been applied to the study of materials manufactured by the authors following the ancient craftsmen methods of forging and quenching. (Author) 16 refs

A review on creatinine measurement techniques.

Science.gov (United States)

Mohabbati-Kalejahi, Elham; Azimirad, Vahid; Bahrami, Manouchehr; Ganbari, Ahmad

2012-08-15

This paper reviews the entire recent global tendency for creatinine measurement. Creatinine biosensors involve complex relationships between biology and micro-mechatronics to which the blood is subjected. Comparison between new and old methods shows that new techniques (e.g. Molecular Imprinted Polymers based algorithms) are better than old methods (e.g. Elisa) in terms of stability and linear range. All methods and their details for serum, plasma, urine and blood samples are surveyed. They are categorized into five main algorithms: optical, electrochemical, impedometrical, Ion Selective Field-Effect Transistor (ISFET) based technique and chromatography. Response time, detection limit, linear range and selectivity of reported sensors are discussed. Potentiometric measurement technique has the lowest response time of 4-10 s and the lowest detection limit of 0.28 nmol L(-1) belongs to chromatographic technique. Comparison between various techniques of measurements indicates that the best selectivity belongs to MIP based and chromatographic techniques. Copyright © 2012 Elsevier B.V. All rights reserved.

The impact of involved node, involved field and mantle field radiotherapy on estimated radiation doses and risk of late effects for pediatric patients with Hodgkin lymphoma

DEFF Research Database (Denmark)

Maraldo, M V; Jørgensen, M; Brodin, N P

2014-01-01

BACKGROUND: The use of radiotherapy (RT) is debated for pediatric patients with Hodgkin lymphoma (HL) due to the late effects of treatment. Radiation doses to the thyroid, heart, lungs, and breasts are compared with the extensive mantle field (MF), Involved Field RT(IFRT), Modified IFRT (m......IFRT), and Involved Node RT (INRT) and the risk of radiation-induced cardiovascular disease, secondary cancers, and the corresponding Life Years Lost (LYL) is estimated with each technique. PROCEDURE: INRT, mIFRT, IFRT, and MF plans (20 and 30 Gy) were simulated for 10 supradiaphragmatic, clinical stage I......–II classical HL patients lung, breast, and thyroid cancer with each technique were estimated. The estimated excess risks attributable to RT were based on HL series with long-term follow...

Selecting a Sustainable Disinfection Technique for Wastewater Reuse Projects

Directory of Open Access Journals (Sweden)

Jorge Curiel-Esparza

2014-09-01

Full Text Available This paper presents an application of the Analytical Hierarchy Process (AHP by integrating a Delphi process for selecting the best sustainable disinfection technique for wastewater reuse projects. The proposed methodology provides project managers a tool to evaluate problems with multiple criteria and multiple alternatives which involve non-commeasurable decision criteria, with expert opinions playing a major role in the selection of these treatment technologies. Five disinfection techniques for wastewater reuse have been evaluated for each of the nine criteria weighted according to the opinions of consulted experts. Finally, the VIKOR method has been applied to determine a compromise solution, and to establish the stability of the results. Therefore, the expert system proposed to select the optimal disinfection alternative is a hybrid method combining the AHP with the Delphi method and the VIKOR technique, which is shown to be appropriate in realistic scenarios where multiple stakeholders are involved in the selection of a sustainable disinfection technique for wastewater reuse projects.

Electronic Creativity Techniques for Organizational Innovation.

Science.gov (United States)

Siau, Keng L.

1996-01-01

Discusses using advanced electronic and communication technology to improve organizational innovation. Group creativity techniques, such as electronic brainstorming, PMI (a brainstorming approach involving plus, minus, and interesting points), synectics, and their verbal counterparts are compared. Electronic PMI and synectics are found to be…

Multiobjective Optimization Involving Quadratic Functions

Directory of Open Access Journals (Sweden)

Oscar Brito Augusto

2014-01-01

Full Text Available Multiobjective optimization is nowadays a word of order in engineering projects. Although the idea involved is simple, the implementation of any procedure to solve a general problem is not an easy task. Evolutionary algorithms are widespread as a satisfactory technique to find a candidate set for the solution. Usually they supply a discrete picture of the Pareto front even if this front is continuous. In this paper we propose three methods for solving unconstrained multiobjective optimization problems involving quadratic functions. In the first, for biobjective optimization defined in the bidimensional space, a continuous Pareto set is found analytically. In the second, applicable to multiobjective optimization, a condition test is proposed to check if a point in the decision space is Pareto optimum or not and, in the third, with functions defined in n-dimensional space, a direct noniterative algorithm is proposed to find the Pareto set. Simple problems highlight the suitability of the proposed methods.

Composição química e resistência mecânica da base de braquetes "Straight-Wire" Superficial hardness and the metallographic characteristics of straight-wire base brackets

Directory of Open Access Journals (Sweden)

Luciana de Paula Gontijo

2004-08-01

Full Text Available Esse trabalho objetivou comparar as durezas superficiais e as características metalográficas das bases de braquetes "straight-wire" de quatro marcas comerciais: Morelli, Abzil Lancer, Unitek e A-Company. As durezas superficiais foram avaliadas por meio de um teste de dureza realizado com o auxílio de um microdurômetro. Os resultados indicaram diferenças entre as marcas comerciais testadas onde os braquetes da A-Company apresentaram os valores mais altos de dureza (314 HV, seguidos da Unitek (325 HV, Abzil (230 HV e Morelli (192 HV. As características metalográficas das bases de braquetes foram avaliadas por meio de um espectrômetro, onde observou-se a presença de elementos de liga como o cromo, o níquel, o silício, o cobre, o alumínio, o enxofre e o nióbio. A quantidade de cada elemento de liga variou entre as marcas, provavelmente devido ao processo de fabricação industrial, mas sem interferir na qualidade final da liga.The objective of this study was to compare the superficial hardness and the metallographic characteristics of the bases of straight-wire brackets. Brackets from four different manufactures were utilized: Morelli, Abzil Lancer, Unitek and A-Company. The superficial hardness test revealed that the A-Company bracket base had the highest value (314 HV followed by Unitek (325 HV, Abzil (230 HV and Morelli (192 HV. The presence of variable amounts of chrome, nickel, silicon, copper, aluminum, sulfur and niobium was detected by the spectrometer. The quantity of each element varied according to the brand tested and did not interfere with the quality of the alloy. This variance was most likely due to differences in the process of the fabrication of each manufactures.

Counselling needs of students involved in indiscipline as expressed ...

African Journals Online (AJOL)

This study therefore examined the counselling needs of students involved in indiscipline as expressed by teachers. The descriptive research design was adopted and a simple random sampling technique was employed in selecting the respondents for the study. Data analysis was carried out using descriptive and inferential ...

Application of digital sampling techniques to particle identification

International Nuclear Information System (INIS)

Bardelli, L.; Poggi, G.; Bini, M.; Carraresi, L.; Pasquali, G.; Taccetti, N.

2003-01-01

An application of digital sampling techniques is presented which can greatly simplify experiments involving sub-nanosecond time-mark determinations and energy measurements with nuclear detectors, used for Pulse Shape Analysis and Time of Flight measurements in heavy ion experiments. In this work a 100 M Sample/s, 12 bit analog to digital converter has been used: examples of this technique applied to Silicon and CsI(Tl) detectors in heavy-ions experiments involving particle identification via Pulse Shape analysis and Time of Flight measurements are presented. The system is suited for applications to large detector arrays and to different kinds of detectors. Some preliminary results regarding the simulation of current signals in Silicon detectors are also discussed. (authors)

Boron steel. I Part. Preparation; Aceros al Boro Parte I. Preparacion

Energy Technology Data Exchange (ETDEWEB)

Jaraiz Franco, E; Esteban Hernandez, J A

1960-07-01

With the advent of the first nuclear reactors arise the need for control rods and shielding duties for some types of radiations. One of the materials used for this purpose has been the high boron steel. This paper describes the melting and casting procedures employed for the production, at laboratory scale, of steels with Boron content ranging from 1 to 4 per cent, as well as the metallographic and X-Ray techniques used for the identification of the present phases. The electrolytic technique employed for the isolation of the Fe{sub 2}B phase and its subsequent X-Ray identification has proved to be satisfactory. (Author) 11 refs.

Boron steel. I Part. Preparation

International Nuclear Information System (INIS)

Jaraiz Franco, E.; Esteban Hernandez, J. A.

1960-01-01

With the advent of the first nuclear reactors arise the need for control rods and shielding duties for some types of radiations. One of the materials used for this purpose has been the high boron steel. This paper describes the melting and casting procedures employed for the production, at laboratory scale, of steels with Boron content ranging from 1 to 4 per cent, as well as the metallographic and X-Ray techniques used for the identification of the present phases. The electrolytic technique employed for the isolation of the Fe 2 B phase and its subsequent X-Ray identification has proved to be satisfactory. (Author) 11 refs

Active learning techniques for librarians practical examples

CERN Document Server

Walsh, Andrew

2010-01-01

A practical work outlining the theory and practice of using active learning techniques in library settings. It explains the theory of active learning and argues for its importance in our teaching and is illustrated using a large number of examples of techniques that can be easily transferred and used in teaching library and information skills to a range of learners within all library sectors. These practical examples recognise that for most of us involved in teaching library and information skills the one off session is the norm, so we need techniques that allow us to quickly grab and hold our

Consolidated techniques for groups of enterprises with complex structure

Directory of Open Access Journals (Sweden)

Cristina Ciuraru-Andrica

2009-12-01

Full Text Available The preparation and disclosure of the financial statements of a group of enterprises involves some consolidation techniques. The Literature presents many techniques, but in practice are used two of them. They will be described first of all in a particular manner and after that in a comparative one. The group of entities can choose one of these techniques, the final result (the consolidated financial statements being the same, whatever the option.

Emerging Dynamic Design Techniques for Mechanical and ...

Indian Academy of Sciences (India)

Emerging Dynamic Design Techniques for Mechanical ... through this school to bring about an awareness of the state-of-art of the software and ... those mentioned above, cannot be ensured on the basis of approaches involving numerical.

Metallographic study of non-homogenous armour impacted by armour-piercing incendiary ammunition

International Nuclear Information System (INIS)

Balos, Sebastian; Sidjanin, Leposava

2011-01-01

Highlights: → Incendiary effect does not influence the changes in microstructure. → Impact causes plastic deformation in more ductile materials. → Impact causes shear crack instability in less ductile materials. → Crack propagation influences chipping on the inside of the perforated plate. -- Abstract: In this paper, the influence of impact and incendiary effect on the microstructure changes and crack development in non-homogenous add-on armour is studied. The main objective was to determine the parameters that may cause the yielding of the material, leading to a possible decrease in multi-hit resistance. For that purpose, patented wire fence and perforated plates made from two types of high strength steel, Hardox 450 and 50CrV4 tempered at 170 o C were tested. Various techniques were applied: high speed video camera was used, visual macroanalysis, light microscopy, scanning electron microscopy and energy dispersive X-ray analysis. It was found that incendiary effect, being of a brief nature, does not have any influence on microstructure of the add-on armour. However, impact greatly influences crack development and propagation, which occurs in 50CrV4 steel, the material with lower ductility, diminishing its multi-hit resistance. In accordance with obtained results, non-homogenous add-on armour behaviour models were devised, describing the influence of material ductility and geometry on fracture mode, stresses and deformability.

Analysis of brand personality to involve event involvement and loyalty: A case study of Jakarta Fashion Week 2017

Science.gov (United States)

Nasution, A. H.; Rachmawan, Y. A.

2018-04-01

Fashion trend in the world changed extremely fast. Fashion has become the one of people’s lifestyle in the world. Fashion week events in several areas can be a measurement of fahion trend nowadays. There was a fashion week event in Indonesia called Jakarta Fashion Week (JFW) aims to show fashion trend to people who want to improve their fashion style. People will join some events if the event has involvement to them, hence they will come to that event again and again. Annually and continuously event is really important to create loyalty among people who are involved in it, in order to increase positive development towards the organizer in organizing the next event. Saving a huge amount from the marketing budget, and creating a higher quality event. This study aims to know the effect of 5 brand personality dimension to event involvement and loyalty in Jakarta Fashion Week (JFW). This study use quantitative confirmative method with Structural Equation Model (SEM) analysis technique. The sample of this study is 150 respondents who became a participant of Jakarta Fashion Week 2017. Result show that there was significant effect of 5 brand personality dimension to 3 dimension of event involvement and loyalty. Meanwhile, there was one dimension of event involvement called personal self-expression that has not effect to loyalty.

The impact of consumer involvement in research: an evaluation of consumer involvement in the London Primary Care Studies Programme.

Science.gov (United States)

Wyatt, Katrina; Carter, Mary; Mahtani, Vinita; Barnard, Angela; Hawton, Annie; Britten, Nicky

2008-06-01

The value of consumer involvement in health services research is widely recognized. While there is a growing body of evidence about the principles of good consumer involvement, there is little research about the effect that involvement can have on the research. This evaluation assessed the level and impact of consumer involvement in the London Primary Care Studies Programme (LPCSP), all of whose individual projects had to demonstrate substantial involvement as a condition of funding. To evaluate consumer involvement in the LPSCP and understand what impact consumers had on the research process and outcomes. A multi-method case study approach was undertaken, using survey techniques, interviews, focus groups, observation and scrutiny of written documents. The overall data set comprised 61 questionnaires, 44 semi-structured interviews, 2 focus groups and 15 hours of observation of meetings. Eleven primary care-based research projects which together made up the LPCSP. An in-depth description of consumer involvement in the Programme was produced. Nine projects had consumers as co-applicants, four projects had been completed before the evaluation began and one was still ongoing at the time of the evaluation. Of the eight projects which have produced final reports, all met their aims and objectives. Consumers had had an additional impact in the research, in the initial design of the study, in recruitment of the research subjects, in developing data collection tools, in collecting the data, in analysis and disseminating the findings. Consumer involvement in National Health Service research is a relatively recent policy development and while there is an increasing amount of literature about how and why consumers should be involved in research, there is less evidence about the impact of such involvement. This evaluation provides evidence about the impact that consumers have not only on the research process but also on the outcomes of the research.

Engineers find climbing techniques work well for dam inspections

Energy Technology Data Exchange (ETDEWEB)

O`Shea, M.; Graves, A. [Bureau of Reclamation, Denver, CO (United States)

1996-10-01

Climbing techniques adopted by the Bureau of Reclamation to inspect previously inaccessible or difficult to reach features at dams are described. Following the failure of the steel radial-arm gate at Folsom Dam, engineers mounted an effort to reach and inspect the dam`s seven other spillway gates. This close-up examination was performed to: (1) determine the condition of these gates; and (2) gather clues about the failure of the one gate. The access techniques described involved mountaineering techniques, as opposed to high scaling techniques, performed with dynamic and static nylon kermantle ropes.

Diagnostic imaging of digestive tract involvement in cystic fibrosis. Part 1: hepatobiliary disease

International Nuclear Information System (INIS)

Miralles, M.; Gonzalez, G.; Serrano, C.; Manzanares, J.; Berrocal, T.

1998-01-01

Cystic fibrosis is a severe hereditary disease characterized by epithelial chloride channel dysfunction, leading to the production of abnormally thick secretions. The abnormal gene is located on the long arm of chromosome 7. Hepatobiliary involvement derives from ductal obstruction causing cholestasis, steatosis, cirrhosis and portal hypertension. Biliary sludge, cholelithiasis and gallbladder sclerosis and atrophy are common findings. As the correlation between the hepatobiliary changes and their clinical and analytical impact is very limited, imaging techniques are essential in this disease. Ultrasound is the basic imaging tool, both for initial evaluation and follow-up of the hepatic and biliary involvement, although other techniques such as radionuclide imaging, magnetic resonance and computed tomography can be highly useful. Given the long-term, chronic nature of this disease, the use of aggressive techniques or irradiation should be carefully weighed. (Author) 38 refs

High temperature cathodic charging of hydrogen in zirconium alloys and iron and nickel base alloys

International Nuclear Information System (INIS)

John, J.T.; De, P.K.; Gadiyar, H.S.

1990-01-01

These investigations lead to the development of a new technique for charging hydrogen into metals and alloys. In this technique a mixture of sulfates and bisulfates of sodium and potassium is kept saturated with water at 250-300degC in an open pyrex glass beaker and electrolysed using platinum anode and the material to be charged as the cathode. Most of the studies were carried out on Zr alloys. It is shown that because of the high hydrogen flux available at the surface and the high diffusivity of hydrogen in metals at these temperatures the materials pick up hydrogen faster and more uniformly than the conventional electrolytic charging at room temperature and high temperature autoclaving in LiOH solutions. Chemical analysis, metallographic examination and XRD studies confirm this. This technique has been used to charge hydrogen into many iron and nickel base austentic alloys, which are very resistant to hydrogen pick up and to H-embrittlement. Since this involved a novel method of electrolysing water, the hydrogen/deuterium isotopic ratio has been studied. At this temperatures the D/H ratio in the evolved hydrogen gas was found to be closer to the value in the liquid water, which means a smaller separation factor. This confirm the earlier observation that separation factor decreases with increase of temperature. (author). 16 refs., 21 fi gs., 6 tabs

A New Continuous Cooling Transformation Diagram for AISI M4 High-Speed Tool Steel

Science.gov (United States)

Briki, Jalel; Ben Slima, Souad

2008-12-01

The increasing evolution of dilatometric techniques now allows for the identification of structural transformations with very low signal. The use of dilatometric techniques coupled with more common techniques, such as metallographic, hardness testing, and x-ray diffraction allows to plot a new CCT diagram for AISI M4 high-speed tool steel. This diagram is useful for a better selection of alternate solutions, hardening, and tempering heat treatments. More accurate determination of the various fields of transformation of austenite during its cooling was made. The precipitation of carbides highlighted at high temperature is at the origin of the martrensitic transformation into two stages (splitting phenomena). For slow cooling rates, it was possible to highlight the ferritic, pearlitic, and bainitic transformation.

Radiologic techniques in evaluation endocrine disorders

International Nuclear Information System (INIS)

Martino, C.R.; Schultz, C.L.; Butler, H.E.; Haaga, J.R.

1988-01-01

This paper discusses evaluation of normal and diseased endocrine organs that has been facilitated by the development of new radiologic-imaging techniques including nuclear medicine, ultrasound, computed tomography, and magnetic resonance imaging. With improvement in resolution and tissue contrast, abnormalities as small as 5 mm can now be imaged with these modalities. Endocrinologists and clinicians involved in the evaluation and diagnosis of patients with endocrine diseases can be substantially aided by a proper radiologic workup. The authors describe and illustrate various radiologic techniques that are useful for evaluating thyroid and parathyroid derangements

Production and manipulation of bovine embryos: techniques and terminology.

Science.gov (United States)

Machaty, Z; Peippo, J; Peter, A

2012-09-15

There are numerous publications regarding bovine embryos, ranging from descriptions of their appearance and development to emerging techniques in the field of assisted reproductive technology. Concurrently, several specialized terms have been developed to describe the bovine embryo. The purpose of the current review is two-fold; it is primarily to describe techniques involved in the in vivo and in vitro production of bovine embryos and their manipulation, and secondarily to summarize specialized terms used in these processes. The intention is not to review these techniques in detail, but instead to provide salient points and current knowledge regarding these techniques, with a focus on terminology. The first review dealt with classical and contemporary terminology used to describe morphologic aspects of ovarian dynamics in cattle. Subsequently, the terms and current understanding of processes involved in preattachment bovine embryos were described in the second review. As the third article in a series, this mini-review is focused on defining the production, manipulation, and transfer of bovine preattachment embryos. Copyright © 2012 Elsevier Inc. All rights reserved.

Parental Involvement and Children's School Achievement: Evidence for Mediating Processes

Science.gov (United States)

Rogers, Maria A.; Theule, Jennifer; Ryan, Bruce A.; Adams, Gerald R.; Keating, Leo

2009-01-01

This study used path analytic techniques and an ecological framework to examine the association between children's perceptions of their parents' educational involvement, children's personal characteristics, and their school achievement. Fathers' academic pressure was predictive of lower achievement, whereas mothers' encouragement and support…

[Parental involvement in cognitive-behavioral therapy for children with anxiety disorders].

Science.gov (United States)

Aydın, Arzu

2014-01-01

A growing body of literature suggests that parents play a critical role in the development and/or maintenance of child anxiety. One of the main purposes of this article is to identify common parental involvement techniques and most common obstacles derived from parents in cognitive behavioral therapy (CBT) with anxious children. Another purpose of the present study is to revise empirical studies comparing child-focused CBT with and without parental involvement. The PsycARTICLES, MEDLINE and PubMed databases were searched to identify articles in English that were published between the years of 1990 and 2012 (October) using the following keywords; (1) anxiety, (2) cognitive behavioral therapy, (3) parental involvement. Studies were only included in this review if they were comparing the treatment effect of child-only CBT and CBT with additional parental components. Thirteen studies were introduced in the context of method (diagnosis of children, age range of children, follow-up, results, etc.) and therapy characteristics (number of sessions, frequency of sessions, treatment components both child focused CBT and CBT with parental involvement, etc.). The common techniques of therapy with parental involvement are psychoeducation, contingency management, cognitive restructuring, reducing parental anxiety, improving parent-child relationship, and relapse prevention. Parental psychopathology, parental inappropriate expectations and family dysfunctions are important difficulties derived from parents in CBT with anxious children. The results of the studies suggested that parental involvement have increased the efficacy of the treatment in CBT especially working with young children and having at least one anxious parent.

High-speed photography. Technique and evolution

International Nuclear Information System (INIS)

Sanchez-Tembleque, R.

1981-01-01

It is intended to present some general considerations about ''Higg-speed photography'' as a tool of work common in mos research laboratories in the world. ''High-speed photography'' relies on the principles of photography of actions, that change rapidly with the time. The evolution of this technique goes along with the discovering of new phenomena in wich higher speeds are involved. At present is normal to deal with changing rates involving picoseconds times (10 -12 s) and new developments on the field of femtosecond (10 -15 s) theoretically are contemplated. (author)

The impact of involved node, involved field and mantle field radiotherapy on estimated radiation doses and risk of late effects for pediatric patients with Hodgkin lymphoma

DEFF Research Database (Denmark)

Maraldo, M. V.; Jorgensen, M.; Brodin, N. P.

2014-01-01

–II classical HL patients 4 x 2 plans for each patient. The lifetime excess risks of cardiac morbidity, cardiac mortality, lung, breast, and thyroid cancer with each technique were estimated. The estimated excess risks attributable to RT were based on HL series with long-term follow......IFRT), and Involved Node RT (INRT) and the risk of radiation-induced cardiovascular disease, secondary cancers, and the corresponding Life Years Lost (LYL) is estimated with each technique. PROCEDURE: INRT, mIFRT, IFRT, and MF plans (20 and 30 Gy) were simulated for 10 supradiaphragmatic, clinical stage I...... to the heart, lungs, breasts, and thyroid compared to past,extended fields, even for patients with mediastinal disease. This translated into a significantly reduced estimated risk of cardiovascular disease, secondary cancers, and LYL. CONCLUSIONS: Involved Node Radiotherapy should be considered for pediatric...

A Monte Carlo Sampling Technique for Multi-phonon Processes

Energy Technology Data Exchange (ETDEWEB)

Hoegberg, Thure

1961-12-15

A sampling technique for selecting scattering angle and energy gain in Monte Carlo calculations of neutron thermalization is described. It is supposed that the scattering is separated into processes involving different numbers of phonons. The number of phonons involved is first determined. Scattering angle and energy gain are then chosen by using special properties of the multi-phonon term.

Quantitative analysis of inclusions in high-strength steels by x-ray computed tomography using ultra-bright synchrotron radiation

International Nuclear Information System (INIS)

Shiozawa, Daiki; Nakai, Yoshikazu; Morikage, Yasushi; Tanaka, Hiroshi; Okado, Hideki; Miyashita, Takuya

2006-01-01

The observation of internal microstructures in materials is important to elucidate the mechanisms of ultra-long life fatigue of high-strength steels, and to ensure the integrity of structures. By conventional techniques, such as laboratory X-ray and ultrasonic imaging, the size and shape of subsurface non-metallic inclusions and cracks, those are smaller than 100 μm, cannot be measured. Then, in the present study, the ultra-bright synchrotron radiation X-ray was applied to the imaging of subsurface inclusion. To obtain basic data for the measurement, the penetration depth of synchrotron radiation wave in a free-cutting steel was examined. It was found that the depths where the transmitted wave cannot be observed are 100 μm for 15 keV, 200 μm for 20 keV, 600 μm for 25 keV, and 800 μm for 30 keV. For the measurement of size and shape of inclusion, synchrotron radiation computed tomography method (SR-CT) was employed. Metallographic structures can be observed in a free-cutting steel, and the diameter of these structures is about 7 - 10 μm. They are considered to be inclusions, which mainly contain manganese sulfide (MnS) or pearlitic phase. To investigate the possibility of detection of pearlitic phase, SR-CT was applied to observe the metallographic structures in carbon steel (S35C), which contains a lot of pearlitic phase and a little inclusion. In this case, no metallographic structure was observed inside specimen. These results indicate that the microstructures those were observed by SR-CT method was inclusions, not pearlitic phase. (author)

Designing Laboratory Exercises for the Undergraduate Molecular Biology/Biochemistry Student: Techniques and Ethical Implications Involved in Personalized Medicine

Science.gov (United States)

Weinlander, Kenneth M.; Hall, David J.

2010-01-01

Personalized medicine refers to medical care that involves genetically screening patients for their likelihood to develop various disorders. Commercial genome screening only involves identifying a consumer's genotype for a few single nucleotide polymorphisms. A phenotype (such as an illness) is greatly influenced by three factors: genes, gene…

Semi-analytic techniques for calculating bubble wall profiles

International Nuclear Information System (INIS)

Akula, Sujeet; Balazs, Csaba; White, Graham A.

2016-01-01

We present semi-analytic techniques for finding bubble wall profiles during first order phase transitions with multiple scalar fields. Our method involves reducing the problem to an equation with a single field, finding an approximate analytic solution and perturbing around it. The perturbations can be written in a semi-analytic form. We assert that our technique lacks convergence problems and demonstrate the speed of convergence on an example potential. (orig.)

Biokinematic structure of techniques wrestlers during pre-basic training

Directory of Open Access Journals (Sweden)

S.V. Sinіgovets

2013-07-01

Full Text Available The theoretical aspects of freestyle wrestlers. Experimentally investigated the structural elements of techniques during pre-basic training. The study involved 28 young fighters. Held video computer analysis techniques. Identified biomechanical characteristics defined kinematic structure of the temporal and spatial-temporal characteristics of the basic techniques. Shown variability of the individual phases of the basic techniques. Structural dynamics of the resulting velocities of the individual body bioelement fighters showed characteristic changes depending on the mode and direction of the motor action. Found that the predominant contribution to the biokinematic structure of technical actions were resulting velocities torso of young fighters.

Microstructure of a SiC/Ti-15-3 composite

Science.gov (United States)

Lerch, B. A.; Hull, D. R.; Leonhardt, T. A.

1990-01-01

A continuous SiC-fiber-reinforced titanium (Ti-15V-3Cr-3Sn-3A1) composite was metallographically examined. Several methods for examining composite materials were investigated and documented. Polishing techniques for this material are described. An interference layering method was developed to reveal the structure of the fiber, the reaction zone, and various phases within the matrix. Microprobe and TEM analyses were performed on the fiber-matrix interface. Detailed descriptions of the fiber distribution and the microstructure of the fiber and matrix are presented.

Improved Nanomechanical Test Techniques for Surface Engineered Materials

Directory of Open Access Journals (Sweden)

Stephen R. Goodes

2010-06-01

Full Text Available The development and implementation of a wide range of innovative nanomechanical test techniques to solve tribological problems in applications as diverse as biomedical and automotive are described in this review. For improved wear resistance and durability, the importance of understanding the system response rather than the coating-only properties is emphasized. There are many applications involving mechanical contact where the key to understanding the problem is to test at higher load and to combine reliable measurements taken across different length scales using both nano- and micro-indentation and related wear measurement techniques which more closely simulate contact conditions to fully understand the mechanical behaviour and hence deliver improved application performance. Results are presented with the NanoTest platform for applications for biomedical devices and surface engineering of lightweight alloys for the automotive industry. By combining results with different techniques it is possible to postulate predictive design rules – based on the elastic and plastic deformation energies involved in contact - to aid the reliable optimisation of mechanical properties in the various contact situations in the different applications.

Comparison of three radiographic methods in screening of temporomandibular joint involvement in patients with psoriatic arthritis

International Nuclear Information System (INIS)

Koenoenen, M.; Kilpinen, E.

1990-01-01

Fifty-three randomly selected subjects with psoriatic arthritis (PA) were examined radiographically by means of orthopantomography, transcranial radiography, and transmaxillary radiography. Two examiners graded the radiographic signs of flattening, osteophytes, erosion, and sclerosis. The findings obtained were then compared to determine the best technique for screening of temporomandibular joint (TMJ) bone changes. Together the techniques showed definite (24%) and possible (6%) changes, suggesting TMJ involvement in 31 of 106 joints. In all projections, radiographic signs suggesting TMJ involvement were most frequent in the condyle. Erosion in the condyle was the most frequent finding. Agreement with regard to definite changes in the condyle was found in only one-third to half of the cases. It is concluded that in radiography of the TMJ in subjects with PA, a combination of radiographic techniques should be used to obtain maximum information. However, orthopantomography is well suited for screening of TMJ involvement in subjects with PA. 30 refs., 2 figs., 3 tabs

Surface modification of EN-C35E steels by thermo-chemical boronizing process and its properties

International Nuclear Information System (INIS)

Yapar, U.; Arisoy, C.F.; Basman, G.; Yesilcubuk, S.A.; Sesen, M.K.

2004-01-01

Boronizing, which involves diffusion of boron atoms into steel substrate to form hard iron borides is well known diffusion coating technique. In this study, salt bath boronizing processes were performed on EN-C35E steel substrate in slurry salt bath containing borax, boric acid as boron sources and ferro-silicon as reductant. The process was performed at 850 and 950 C for 2, 4, 6 and 8 hours. Boride layers were examined by optical microscope (OM), scanning electron microscope (SEM) and X-ray diffraction (XRD). Hardness of borides formed on the steel substrate was measured by knoop indenter under load of 0.5N. Metallographic studies and XRD analysis revealed that single-type Fe 2 B layers were formed. Depending on boronizing time and temperature, it has found that the hardness of boride layer ranged from 1895-2143 HK 0.05 that is nearly 8 times higher than substrate hardness. The thickness of the layer ranged from 25 to 167 μm depending on boronizing time and temperature. (orig.)

Characterization of an Indian sword: classic and noninvasive methods of investigation in comparison

Science.gov (United States)

Barzagli, E.; Grazzi, F.; Williams, A.; Edge, D.; Scherillo, A.; Kelleher, J.; Zoppi, M.

2015-04-01

The evolution of metallurgy in history is one of the most interesting topics in Archaeometry. The production of steel and its forging methods to make tools and weapons are topics of great interest in the field of the history of metallurgy. In the production of weapons, we find almost always the highest level of technology. These were generally produced by skilled craftsmen who used the best quality materials available. Indian swords are an outstanding example in this field and one of the most interesting classes of objects for the study of the evolution of metallurgy. This work presents the study of a Shamsheer (a sword with a curved blade with single edge) made available by the Wallace Collection in London. The purpose of this study was to determine the composition, the microstructure, the level and the direction of residual strain and their distribution in the blade. We have used two different approaches: the classical one (metallography) and a nondestructive technique (neutron diffraction): In this way, we can test differences and complementarities of these two techniques. To obtain a good characterization of artifacts studied by traditional analytical methods, an invasive approach is required. However, the most ancient objects are scarce in number, and the most interesting ones are usually in an excellent state of conservation, so it is unthinkable to apply techniques with a destructive approach. The analysis of blades that has been performed by metallographic microscopy has demonstrated the specificity of the production of this type of steel. However, metallographic analysis can give only limited information about the structural characteristics of these artifacts of high quality, and it is limited to the sampled areas. The best approach for nondestructive analysis is therefore to use neutron techniques.

Heat Transfer and Cooling Techniques at Low Temperature

CERN Document Server

Baudouy, B

2014-07-17

The first part of this chapter gives an introduction to heat transfer and cooling techniques at low temperature. We review the fundamental laws of heat transfer (conduction, convection and radiation) and give useful data specific to cryogenic conditions (thermal contact resistance, total emissivity of materials and heat transfer correlation in forced or boiling flow for example) used in the design of cooling systems. In the second part, we review the main cooling techniques at low temperature, with or without cryogen, from the simplest ones (bath cooling) to the ones involving the use of cryocoolers without forgetting the cooling flow techniques.

Application of pattern recognition techniques to crime analysis

Energy Technology Data Exchange (ETDEWEB)

Bender, C.F.; Cox, L.A. Jr.; Chappell, G.A.

1976-08-15

The initial goal was to evaluate the capabilities of current pattern recognition techniques when applied to existing computerized crime data. Performance was to be evaluated both in terms of the system's capability to predict crimes and to optimize police manpower allocation. A relation was sought to predict the crime's susceptibility to solution, based on knowledge of the crime type, location, time, etc. The preliminary results of this work are discussed. They indicate that automatic crime analysis involving pattern recognition techniques is feasible, and that efforts to determine optimum variables and techniques are warranted. 47 figures (RWR)

Heat Transfer and Cooling Techniques at Low Temperature

Energy Technology Data Exchange (ETDEWEB)

Baudouy, B [Saclay (France)

2014-07-01

The first part of this chapter gives an introduction to heat transfer and cooling techniques at low temperature. We review the fundamental laws of heat transfer (conduction, convection and radiation) and give useful data specific to cryogenic conditions (thermal contact resistance, total emissivity of materials and heat transfer correlation in forced or boiling flow for example) used in the design of cooling systems. In the second part, we review the main cooling techniques at low temperature, with or without cryogen, from the simplest ones (bath cooling) to the ones involving the use of cryocoolers without forgetting the cooling flow techniques.

FPGA based mixed-signal circuit novel testing techniques

International Nuclear Information System (INIS)

Pouros, Sotirios; Vassios, Vassilios; Papakostas, Dimitrios; Hristov, Valentin

2013-01-01

Electronic circuits fault detection techniques, especially on modern mixed-signal circuits, are evolved and customized around the world to meet the industry needs. The paper presents techniques used on fault detection in mixed signal circuits. Moreover, the paper involves standardized methods, along with current innovations for external testing like Design for Testability (DfT) and Built In Self Test (BIST) systems. Finally, the research team introduces a circuit implementation scheme using FPGA

A comparison of etchants for quantitative metallography of bainite and martensite microstructures in Fe-C-Mo alloys

International Nuclear Information System (INIS)

Shui, C.K.; Reynolds, W.T. Jr.; Shiflet, G.J.; Aaronson, H.I.

1988-01-01

Quantitative metallography is the most reliable method available for evaluating isothermal transformation kinetics in steel. However, the accuracy of this method depends on the metallographer's ability to reveal the microstructural constituents of a specimen with sufficient contrast to allow rapid identification either by manual techniques or through the use of an automatic image analyzer. Many of the reagents commonly employed to etch steels do not consistently expose all orientations of ferrite and are thus unsatisfactory for quantitative metallographic studies. Recent research on the kinetics of the bainite reaction in Fe-C-Mo alloys has led to the development of reliable methods for etching microstructures consisting of bainite andor ferrite and various proportions of martensite. This article compares a number of reagents used in studying Fe-C-Mo alloys, having carbon contents ranging from 0.08 to 0.27 wt% and molybdenum contents from 0.25 to 4.28 wt%. These alloys are isothermally reacted at temperatures ranging from slightly above that of the bay in the TTT curve for initiation of transformation down nearly to the M/sub s/. The authors evaluate their suitability for quantitative metallography

Application of expert elicitation techniques in human reliability, assessment

International Nuclear Information System (INIS)

Sanyasi Rao, V.V.S.; Saraf, R.K.; Ghosh, A.K.; Kushwaha, H.S.

2006-01-01

Expert elicitation techniques are being used, in the area of technological forecasting, in estimating data needed for analysis when it is either difficult to arrive at the data by experimental means or when it is quite involved to plan and conduct the experiment. In this study, expert elicitation techniques are applied to the evaluation of the frequencies of the various accident sequences that can result from the initiating event (IE) 'High Pressure Process Water (HPPW) system failure' in typical Indian Pressurised Heavy Water Reactor (IPHWR) of the older generation. The Operating Procedure under Emergency Conditions (OPEC) for this IE involves human actions according to a pre-defined procedure. The Human Error Probabilities for all these human actions are obtained using expert elicitation techniques. These techniques aim at eliciting the opinion of the experts in the area of interest with regard to the issue in question. The uncertainty is analysed by employing the measure of dissonance and the most probable range of human error probabilities are arrived at by maximizing this measure. These values are combined using the same procedures mentioned above to yield a distribution representing the uncertainty associated with the predictions. (author)

The gauge technique in supersymmetric QED2

NARCIS (Netherlands)

Roo, M. de; Steringa, J.J.

1988-01-01

We construct an extension of the gauge technique to two-dimensional supersymmetric gauge theories. This involves a derivation of the spectral representation of a scalar superpropagator in two dimensions. We apply the method to the massive supersymmetric Schwinger model. In the case that the gauge

An Introduction to the Space Mapping Technique

DEFF Research Database (Denmark)

Bakr, Mohamed H.; Bandler, John W.; Madsen, Kaj

2001-01-01

The space mapping technique is intended for optimization of engineering models which involve very expensive function evaluations. It is assumed that two different models of the same physical system are available: Besides the expensive model of primary interest (denoted the fine model), access to ...

Real-time measurement of electron beam weld penetration in uranium by acoustic emission monitoring

International Nuclear Information System (INIS)

Whittaker, J.W.; Murphy, J.L.

1991-07-01

High quality electron beam (EB) welds are required in uranium test articles. Acoustic emission (AE) techniques are under development with the goal of measuring weld penetration in real-time. One technique, based on Average Signal Level (ASL) measurement was used to record weld AE signatures. Characteristic AE signatures were recorded for bead-on-plate (BOP) and butt joint (BJ) welds made under varied welding conditions. AE waveforms were sampled to determine what microscopic AE behavior led to the observed macroscopic signature features. Deformation twinning and weld expulsion are two of the main sources of emission. AE behavior was correlated with weld penetration as measured by standard metallographic techniques. The ASL value was found to increase approximately linearly with weld penetration in BJ welds. These results form the basis for a real-time monitoring technique for weld penetration. 5 refs

Automatic quantitative metallography

International Nuclear Information System (INIS)

Barcelos, E.J.B.V.; Ambrozio Filho, F.; Cunha, R.C.

1976-01-01

The quantitative determination of metallographic parameters is analysed through the description of Micro-Videomat automatic image analysis system and volumetric percentage of perlite in nodular cast irons, porosity and average grain size in high-density sintered pellets of UO 2 , and grain size of ferritic steel. Techniques adopted are described and results obtained are compared with the corresponding ones by the direct counting process: counting of systematic points (grid) to measure volume and intersections method, by utilizing a circunference of known radius for the average grain size. The adopted technique for nodular cast iron resulted from the small difference of optical reflectivity of graphite and perlite. Porosity evaluation of sintered UO 2 pellets is also analyzed [pt

Who and What Does Involvement Involve?

DEFF Research Database (Denmark)

Hansen, Jeppe Oute; Petersen, Anders; Huniche, Lotte

2015-01-01

This article gives an account of aspects of a multi-sited field study of involvement of relatives in Danish psychiatry. By following metaphors of involvement across three sites of the psychiatric systema family site, a clinical site and a policy sitethe first author (J.O.) investigated how...... theoretical perspective laid out by Ernesto Laclau and Chantal Mouffe, the aim of this study is to show how the dominant discourse about involvement at the political and clinical sites is constituted by understandings of mentally ill individuals and by political objectives of involvement. The analysis...... the responsibility toward the mental health of the ill individual as well as toward the psychological milieu of the family....

Comparison of experimental techniques for characterization of through-thickness texture variations

DEFF Research Database (Denmark)

Mishin, Oleg; Lauridsen, E.M.; Krieger Lassen, N.C.

1999-01-01

For the investigation of through-thickness texture gradients, a number of layers in rolled plates and sheets are inspected. Crystallographic textures in different layers can be characterized using several techniques. In the present work, traditional low-energy X-ray diffraction, the electron...... backscattering pattern technique in the scanning electron microscope and a novel technique which involves high energy synchrotron radiation are used for characterization of through-thickness texture variations in commercial purity cold-rolled aluminium. Important experimental aspects of these three techniques...

Failure analysis of radioisotopic heat source capsules tested under multi-axial conditions

International Nuclear Information System (INIS)

Zielinski, R.E.; Stacy, E.; Burgan, C.E.

In order to qualify small radioisotopic heat sources for a 25-yr design life, multi-axial mechanical tests were performed on the structural components of the heat source. The results of these tests indicated that failure predominantly occurred in the middle of the weld ramp-down zone. Examination of the failure zone by standard metallographic techniques failed to indicate the true cause of failure. A modified technique utilizing chemical etching, scanning electron microscopy, and energy dispersive x-ray analysis was employed and dramatically indicated the true cause of failure, impurity concentration in the ramp-down zone. As a result of the initial investigation, weld parameters for the heat sources were altered. Example welds made with a pulse arc technique did not have this impurity buildup in the ramp-down zone

Experimental analysis of cut welding in aluminium

DEFF Research Database (Denmark)

Dorph, Pernille; De Chiffre, Leonardo; Bay, Niels

1993-01-01

Cut welding is a newly developed cold pressure welding process. In the present work, an experimental investigation was carried out analyzing the mechanisms involved in cut welding of a block to a strip. Experiments were carried out in technically pure aluminium. The investigation has involved...... tensile testing and metallographic investigations of the welds. The results show that this variant of cut welding is a very reproducible process giving a weld strength equal to 30-40% the strength of the parent material. The experiments have shown that the reason for this relatively low strength...... is an uneven pressure distribution along the weld due to a wave formed during sliding. Attempts to alter the material flow during sliding are presented....

Zircaloy-4 hydridation

International Nuclear Information System (INIS)

Vizcaino, Pablo

1997-01-01

The objectives of this work can be summarized as: 1) To reproduce, by heat treatments, matrix microstructures and hydride morphologies similar to those observed in structural components of the CNA-1 and CNE nuclear power plants; 2) To study the evolution of the mechanical properties of the original material with different hydrogen concentrations, such as microhardness, and its capacity to distinguish these materials; 3) To find parameters that allow to estimate the hydrogen content of a material by quantitative metallographic techniques, to be used as complementary in the study of the radioactive materials from reactors

Electrochemical characterisation speeds up prediction of corrosion behaviour

Energy Technology Data Exchange (ETDEWEB)

Schuring, E.W.; Hooijmans, J.W. [ECN Environment and Energy Engineering, Petten (Netherlands)

2013-04-15

The contents of this presentation show the following elements: Introduction; Corrosion in real life; Why Electrochemical characterisation of corrosion; Applications (corrosion resistance coatings, corrosion behaviour (brazed) joints); Available electrochemical corrosion techniques; Standards; Conclusions. In the Conclusions the corrosion screening method is summarized: ECN method fast; within 1h -1 week results depending on test method; Fast pre-selection of promising materials/combinations (cost savings); Determining of corrosion initiation; Determination of corrosion mechanisms and propagation; Life time predictions possible; Strong combination with metallographic post-investigation; Ranking materials / constructions for corrosion performance.

As-received microstructure of a SiC/Ti-15-3 composite

Science.gov (United States)

Lerch, Bradley A.; Hull, David R.; Leonhardt, Todd A.

1988-01-01

A silicon carbide fiber reinforced titanium (Ti-15V-3Cr-3Sn-3Al) composite is metallographically examined. Several methods for examining composite materials are investigated and documented. Polishing techniques for this material are described. An interference layering method is developed to reveal the structure of the fiber, the reaction zone, and various phases within the matrix. Microprobe and transmission electron microscope (TEM) analyses are performed on the fiber/matrix interface. A detailed description of the fiber distribution as well as the microstructure of the fiber and matrix are presented.

Intelligent techniques in engineering management theory and applications

CERN Document Server

Onar, Sezi

2015-01-01

This book presents recently developed intelligent techniques with applications and theory in the area of engineering management. The involved applications of intelligent techniques such as neural networks, fuzzy sets, Tabu search, genetic algorithms, etc. will be useful for engineering managers, postgraduate students, researchers, and lecturers. The book has been written considering the contents of a classical engineering management book but intelligent techniques are used for handling the engineering management problem areas. This comprehensive characteristics of the book makes it an excellent reference for the solution of complex problems of engineering management. The authors of the chapters are well-known researchers with their previous works in the area of engineering management.

Doppler ultrasound surveillance in deep tunneling compressed-air work with Trimix breathing: bounce dive technique compared to saturation-excursion technique.

Science.gov (United States)

Vellinga, T P van Rees; Sterk, W; de Boer, A G E M; van der Beek, A J; Verhoeven, A C; van Dijk, F J H

2008-01-01

The Western Scheldt Tunneling Project in The Netherlands provided a unique opportunity to evaluate two deep-diving techniques with Doppler ultrasound surveillance. Divers used the bounce diving techniques for repair and maintenance of the TBM. The tunnel boring machine jammed at its deepest depth. As a result the work time was not sufficient. The saturation diving technique was developed and permitted longer work time at great depth. Thirty-one divers were involved in this project. Twenty-three divers were examined using Doppler ultrasound. Data analysis addressed 52 exposures to Trimix at 4.6-4.8 bar gauge using the bounce technique and 354 exposures to Trimix at 4.0-6.9 bar gauge on saturation excursions. No decompression incidents occurred with either technique during the described phase of the project. Doppler ultrasound revealed that the bubble loads assessed in both techniques were generally low. We find out, that despite longer working hours, shorter decompression times and larger physical workloads, the saturation-excursion technique was associated with significant lower bubble grades than in the bounce technique using Doppler Ultrasound. We conclude that the saturation-excursion technique with Trimix is a good option for deep and long exposures in caisson work. The Doppler technique proved valuable, and it should be incorporated in future compressed-air work.

Nanorobotics current approaches and techniques

CERN Document Server

Ferreira, Antoine

2013-01-01

Nanorobot devices now perform a wide variety of tasks at the nanoscale in a wide variety of fields including but not limited to fields such as manufacturing, medicine, supply chain, biology, and outer space. Nanorobotics: Current Approaches and Techniques is a comprehensive overview of this interdisciplinary field with a wide ranging discussion that includes nano-manipulation and industrial nanorobotics, nanorobotics in biology and medicine, nanorobotic sensing, navigation and swarm behavior, and protein and DNA-based nanorobotics. Also included is the latest on topics such as bio-nano-actuators and propulsion and navigation of nanorobotic systems using magnetic fields. Nanorobotics: Current Approaches and Techniques is an ideal book for scientists, researchers, and engineers actively involved in applied and robotic research and development.

Acquainting Future Office Employees with Productivity-Improvement Techniques.

Science.gov (United States)

Quible, Zane K.

1982-01-01

Examines factors affecting productivity (government regulations, energy costs, decline in the work ethic, capital investment, number of service workers, work force characteristics, management practices, and unions), and techniques to improve productivity (employee involvement, job structure, communication, flexitime, employee upgrading, incentive…

VALUATION TECHNIQUES USED IN FAIR VALUE MEASUREMENT

Directory of Open Access Journals (Sweden)

Cristina-Aurora, BUNEA-BONTAS

2013-12-01

Full Text Available Valuation of assets and liabilities involves significant judgements and estimates, especially when fair value measurement is required. Currently, IFRS 13 Fair Value Measurement offers a single and more comprehensive source of guidance that is applied to almost all fair value estimates. When measuring fair value of fixed assets, intangible assets, specified financial assets or liabilities, different valuation techniques may be used: the market approach, the cost approach and the income approach. This article reviews these techniques and points out that different valuation practices may provide different results depending on the item being fair valued and on the inputs used. Also it emphasizes that, in particular circumstances, there is the possibility that a certain technique may be more appropriate than other.

Video: two novel endoscopic esophageal lengthening and reconstruction techniques.

Science.gov (United States)

Perretta, Silvana; Wall, James K; Dallemagne, Bernard; Harrison, Michael; Becmeur, François; Marescaux, Jacques

2011-10-01

Esophageal reconstruction presents a significant clinical challenge in patients ranging from neonates with long-gap esophageal atresia to adults after esophageal resection. Both gastric and colonic replacement conduits carry significant morbidity. As emerging organ-sparring techniques become established for early stage esophageal tumors, less morbid reconstruction techniques are warranted. We present two novel endoscopic approaches for esophageal lengthening and reconstruction in a porcine model. Two models of esophageal defects were created in pigs (30-35 kg) under general anesthesia and subsequently reconstructed with the novel techniques. The first model was a segmental defect of the esophagus created by thoracoscopically transecting the esophagus above the gastroesophageal (GE) junction. The first reconstruction technique involved bilateral submucosal endoscopic lengthening myotomies (BSELM) with a magnetic compression anastomosis (MAGNAMOSIS™). The second model was a wedge defect in the anterior esophagus created above the GE junction through a laparotomy. The second reconstruction technique involved an inverted mucosal-submucosal sleeve transposition graft (IMSTG) that crossed the esophageal gap and was secured in place with a self-expandable covered esophageal stent. Both techniques were feasible in the pig model. The BSELM approach lengthened the esophagus 1 cm for every 2 cm length of myotomy. The myotomy targeted only the inner circular fibers of the esophagus, with preservation of the longitudinal layer to protect against long-term dilation and pouching. The IMSTG approach generated a vascularized mucosal graft almost as long as the esophagus itself. Emerging endoscopic capabilities are enabling complex endoluminal esophageal procedures. BSELM and IMSTG are two novel and technically feasible approaches to esophageal lengthening and reconstruction. Further survival studies are needed to establish the safety and efficacy of these techniques.

Differential geometry techniques for sets of nonlinear partial differential equations

Science.gov (United States)

Estabrook, Frank B.

1990-01-01

An attempt is made to show that the Cartan theory of partial differential equations can be a useful technique for applied mathematics. Techniques for finding consistent subfamilies of solutions that are generically rich and well-posed and for introducing potentials or other usefully consistent auxiliary fields are introduced. An extended sample calculation involving the Korteweg-de Vries equation is given.

Mean-Variance-Validation Technique for Sequential Kriging Metamodels

International Nuclear Information System (INIS)

Lee, Tae Hee; Kim, Ho Sung

2010-01-01

The rigorous validation of the accuracy of metamodels is an important topic in research on metamodel techniques. Although a leave-k-out cross-validation technique involves a considerably high computational cost, it cannot be used to measure the fidelity of metamodels. Recently, the mean 0 validation technique has been proposed to quantitatively determine the accuracy of metamodels. However, the use of mean 0 validation criterion may lead to premature termination of a sampling process even if the kriging model is inaccurate. In this study, we propose a new validation technique based on the mean and variance of the response evaluated when sequential sampling method, such as maximum entropy sampling, is used. The proposed validation technique is more efficient and accurate than the leave-k-out cross-validation technique, because instead of performing numerical integration, the kriging model is explicitly integrated to accurately evaluate the mean and variance of the response evaluated. The error in the proposed validation technique resembles a root mean squared error, thus it can be used to determine a stop criterion for sequential sampling of metamodels

New techniques available for decontamination

International Nuclear Information System (INIS)

Costes, J.R.; Cochaux, C.

1996-01-01

As nuclear industry dismantling operations become more widespread, one naturally sees the growth of specific needs in decontamination techniques. In this paper, the authors present two applications involving the decategorization of wastes from dismantling. Decategorization means using decontamination to transform the wastes into a lower, and thus cheaper, category. The first application is in decategorizing large mild steel pipes, which come from the stage decommissioning of the G2/G3 graphite gas reactors at Marcoule. A large number of these pipes (4000 t) have been contaminated by deposits and encrustations of 60 Co (95%) and 137 Cs (5%) to the extent of 200 Bq/cm 2 . The objective was to avoid having to store them on surface sites for 300 yr. This is achieved by decontaminating them to a level that enables the metal to be reused. The other application involves stainless steel waste cut into small sections, which comes from the stage decommissioning of a radiometallurgy laboratory (RM2) at Fontenay aux Roses. This waste was not acceptable to the surface storage center due to high levels of alpha contamination. A decategorization technique has been developed for part of the 13 tonnes of waste concerned, which avoids the need for it to be disposed of in extremely costly geologic repositories

Involvement of Machine Learning for Breast Cancer Image Classification: A Survey.

Science.gov (United States)

Nahid, Abdullah-Al; Kong, Yinan

2017-01-01

Breast cancer is one of the largest causes of women's death in the world today. Advance engineering of natural image classification techniques and Artificial Intelligence methods has largely been used for the breast-image classification task. The involvement of digital image classification allows the doctor and the physicians a second opinion, and it saves the doctors' and physicians' time. Despite the various publications on breast image classification, very few review papers are available which provide a detailed description of breast cancer image classification techniques, feature extraction and selection procedures, classification measuring parameterizations, and image classification findings. We have put a special emphasis on the Convolutional Neural Network (CNN) method for breast image classification. Along with the CNN method we have also described the involvement of the conventional Neural Network (NN), Logic Based classifiers such as the Random Forest (RF) algorithm, Support Vector Machines (SVM), Bayesian methods, and a few of the semisupervised and unsupervised methods which have been used for breast image classification.

Involvement of Machine Learning for Breast Cancer Image Classification: A Survey

Directory of Open Access Journals (Sweden)

Abdullah-Al Nahid

2017-01-01

Full Text Available Breast cancer is one of the largest causes of women’s death in the world today. Advance engineering of natural image classification techniques and Artificial Intelligence methods has largely been used for the breast-image classification task. The involvement of digital image classification allows the doctor and the physicians a second opinion, and it saves the doctors’ and physicians’ time. Despite the various publications on breast image classification, very few review papers are available which provide a detailed description of breast cancer image classification techniques, feature extraction and selection procedures, classification measuring parameterizations, and image classification findings. We have put a special emphasis on the Convolutional Neural Network (CNN method for breast image classification. Along with the CNN method we have also described the involvement of the conventional Neural Network (NN, Logic Based classifiers such as the Random Forest (RF algorithm, Support Vector Machines (SVM, Bayesian methods, and a few of the semisupervised and unsupervised methods which have been used for breast image classification.

Fractures of the proximal humerus involving the intertubercular groove

International Nuclear Information System (INIS)

Ahovuo, J.; Paavolainen, P.; Bjoerkenheim, J.M.; Helsinki Univ. Central Hospital

1989-01-01

The purpose of this study was to analyse the involvement of the gliding surface of the biceps tendon in fractures of the proximal humerus. Fifteen patients had a fracture of the proximal humerus verified with antero-posterior and axillary radiographs. Tangential radiographs of the intertubercular groove, obtained from the shoulder joint, showed involvement of the intertubercular groove in 13 patients (87%), which could not be shown with other projections. Groove radiographs revealed in 3 patients a dislocation of the fragments of the greater tuberosity large enough to require surgical treatment, but which had not been found using conventional techniques. Therefore, a groove radiograph should be used to precise fractures of the proximal humerus. (orig.)

Metallographic study of the system ZrHx

Energy Technology Data Exchange (ETDEWEB)

Whitwham, D.

1961-10-15

American investigators of the system zirconium-hydrogen are in frequent disagreement over their experimental observations. One of the best articles on zirconium hydride, which does much to resolve these differences of opinion, has not been widely translated from the original French. The following translation is offered in an effort to supply a much needed clarification of the behavior of the several phases in the system zirconium-hydrogen.

Metallographic quality control of welding and brazing

International Nuclear Information System (INIS)

Slaughter, G.M.

1979-01-01

The value of metallography in assuring integrity in the fabrication of metal and components in energy systems is summarized. Metallography also plays an integral role in quality control of welded and brazed joints

CERTAIN INEQUALITIES INVOLVING THE Q-DEFORMED GAMMA FUNCTION

Directory of Open Access Journals (Sweden)

K. Nantomah

2014-11-01

Full Text Available This paper in inspired by the work of J.Sándor in 2006. In paper, the authors establish some double inequalities involving the ratio (Γq(x+1/(Γq(x+1/2, where Γq(x is the q-deformation of the classical Gamma function denoted by Γ(x. The method employed in presenting the results makes use of Jackson׳s q-integral representation of the q-deformed Gamma function. In addition, Hőlder׳s inequality for the q-integral, as well as some basic analytical techniques involving the q-analogue of the psi function are used. As a consequence, q-analogues of the classical Wendel׳s asymptotic relation are obtained. At the end, sharpness of the inequalities established in this paper is investigated.

Medical X-ray techniques in diagnostic radiography. 4. ed.

International Nuclear Information System (INIS)

Plaats, G.J. van der; Vijlbrief, P.

1980-01-01

A step by step account is given of every aspect of the technical factors involved in the production of X-ray images. Chapter titles include, methods of image formation and laws of projection, sharpness and unsharpness, contrast, perceptibility of detail in the radiographic image-image quality, properties of fluoroscopic screens, radiographic films, intensifying screens and cassettes, image intensification and X-ray television, processing technique, fluoroscopy and radiographic technique in general, special radiographic techniques, radiographic examinations using contrast media, exposure and exposure tables and automatic density control, diagnostic X-ray apparatus, and diagnostic stands and accessories. (C.F.)

Psoriatic arthritis: imaging techniques

Directory of Open Access Journals (Sweden)

E. Lubrano

2012-06-01

Full Text Available Imaging techniques to assess psoriatic arthritis (PsA include radiography, ultrasonography (US, magnetic resonance imaging (MRI, computed tomography (CT and bone scintigraphy. The radiographic hallmark of PsA is the combination of destructive changes (joint erosions, tuft resorption, osteolysis with bone proliferation (including periarticular and shaft periostitis, ankylosis, spur formation and non-marginal syndesmophytes. US has an increasing important role in the evaluation of PsA. In fact, power Doppler US is useful mainly for its ability to assess musculoskeletal (joints, tendons, entheses and cutaneous (skin and nails involvement, to monitor efficacy of therapy and to guide steroid injections at the level of inflamed joints, tendon sheaths and entheses. MRI allows direct visualization of inflammation in peripheral and axial joints, and peripheral and axial entheses, and has dramatically improved the possibilities for early diagnosis and objective monitoring of the disease process in PsA. MRI has allowed explaining the relationships among enthesitis, synovitis and osteitis in PsA, supporting a SpA pattern of inflammation where enthesitis is the primary target of inflammation. CT has little role in assessment of peripheral joints, but it may be useful in assessing elements of spine disease. CT accuracy is similar to MRI in assessment of erosions in sacroiliac joint involvement, but CT is not as effective in detecting synovial inflammation. Bone scintigraphy lacks specificity and is now supplanted with US and MRI techniques.

Biosensing Using Magnetic Particle Detection Techniques

Directory of Open Access Journals (Sweden)

Yi-Ting Chen

2017-10-01

Full Text Available Magnetic particles are widely used as signal labels in a variety of biological sensing applications, such as molecular detection and related strategies that rely on ligand-receptor binding. In this review, we explore the fundamental concepts involved in designing magnetic particles for biosensing applications and the techniques used to detect them. First, we briefly describe the magnetic properties that are important for bio-sensing applications and highlight the associated key parameters (such as the starting materials, size, functionalization methods, and bio-conjugation strategies. Subsequently, we focus on magnetic sensing applications that utilize several types of magnetic detection techniques: spintronic sensors, nuclear magnetic resonance (NMR sensors, superconducting quantum interference devices (SQUIDs, sensors based on the atomic magnetometer (AM, and others. From the studies reported, we note that the size of the MPs is one of the most important factors in choosing a sensing technique.

Advanced analysis technique for the evaluation of linear alternators and linear motors

Science.gov (United States)

Holliday, Jeffrey C.

1995-01-01

A method for the mathematical analysis of linear alternator and linear motor devices and designs is described, and an example of its use is included. The technique seeks to surpass other methods of analysis by including more rigorous treatment of phenomena normally omitted or coarsely approximated such as eddy braking, non-linear material properties, and power losses generated within structures surrounding the device. The technique is broadly applicable to linear alternators and linear motors involving iron yoke structures and moving permanent magnets. The technique involves the application of Amperian current equivalents to the modeling of the moving permanent magnet components within a finite element formulation. The resulting steady state and transient mode field solutions can simultaneously account for the moving and static field sources within and around the device.

TAEKWONDO TECHNIQUES AND COMPETITION CHARACTERISTICS INVOLVED IN TIME-LOSS INJURIES

Directory of Open Access Journals (Sweden)

Konstantinos Beis

2007-10-01

Full Text Available The purpose of this study was to assess time-loss injuries in young and adult taekwondo athletes. Participants were 2739 children (11-13 years, Junior (14-17 years and adult males and females (18 years and older competing in the national Greek championships. Injury data were collected by project staff with all diagnoses made by the tournament physician. Odds ratios were computed as well as 95% confidence intervals around the injury rates. The female Juniors had a higher time-loss injury rate (Fisher's Exact Test p = 0.033 than their adult counterparts. However, they were not at a higher risk of incurring a time-loss injury: OR = 0.143, 95% CI: 0.018-1.124. Collapsed over age, the females as a group recorded more time-loss injuries [11.36/1,000 A-E (95% CI: 6.25-16.47 versus 7.40/1,000 A-E (95% CI: 4.44-10.36], but this was not significant (OR = 0.703, 95% CI: 0.383-1.293. In the Juniors, the boys only incurred time-loss injuries to the head and neck. There was no difference in the Junior girls in the distribution of time-loss injuries across body region, although they were at higher risk of sustaining an injury to the head and neck (OR = 1.510, 95% CI: 0.422-5.402 but this was not statistically significant. Although there were no statistical differences among age groups within gender, the Junior boys and girls (11-13 years sustained more cerebral concussions. The Junior boys were at a higher risk of incurring a cerebral concussion than the boys (OR = 7.871, 95% CI: 0.917-67.583, Fisher's Exact Test p = 0.036. In the males, there was no difference between the men and Junior boys in injury rate for swing kicks compared to other techniques (OR = 2.000, 95% CI = 0.397-28.416. There also was no difference between the men and boys (OR = 4.800, 95% CI: 0.141-58.013. To help reduce the incidence of time-loss injuries in taekwondo, especially cerebral concussions, it is suggested for coaches to emphasize blocking skills. Educating referees, coaches and

A pilot modeling technique for handling-qualities research

Science.gov (United States)

Hess, R. A.

1980-01-01

A brief survey of the more dominant analysis techniques used in closed-loop handling-qualities research is presented. These techniques are shown to rely on so-called classical and modern analytical models of the human pilot which have their foundation in the analysis and design principles of feedback control. The optimal control model of the human pilot is discussed in some detail and a novel approach to the a priori selection of pertinent model parameters is discussed. Frequency domain and tracking performance data from 10 pilot-in-the-loop simulation experiments involving 3 different tasks are used to demonstrate the parameter selection technique. Finally, the utility of this modeling approach in handling-qualities research is discussed.

Least-squares methods involving the H{sup -1} inner product

Energy Technology Data Exchange (ETDEWEB)

Pasciak, J.

1996-12-31

Least-squares methods are being shown to be an effective technique for the solution of elliptic boundary value problems. However, the methods differ depending on the norms in which they are formulated. For certain problems, it is much more natural to consider least-squares functionals involving the H{sup -1} norm. Such norms give rise to improved convergence estimates and better approximation to problems with low regularity solutions. In addition, fewer new variables need to be added and less stringent boundary conditions need to be imposed. In this talk, I will describe some recent developments involving least-squares methods utilizing the H{sup -1} inner product.

Particle Handling Techniques in Microchemical Processes

Directory of Open Access Journals (Sweden)

Brian S. Flowers

2012-08-01

Full Text Available The manipulation of particulates in microfluidics is a challenge that continues to impact applications ranging from fine chemicals manufacturing to the materials and the life sciences. Heterogeneous operations carried out in microreactors involve high surface-to-volume characteristics that minimize the heat and mass transport resistances, offering precise control of the reaction conditions. Considerable advances have been made towards the engineering of techniques that control particles in microscale laminar flow, yet there remain tremendous opportunities for improvements in the area of chemical processing. Strategies that have been developed to successfully advance systems involving heterogeneous materials are reviewed and an outlook provided in the context of the challenges of continuous flow fine chemical processes.

Weighted hybrid technique for recommender system

Science.gov (United States)

Suriati, S.; Dwiastuti, Meisyarah; Tulus, T.

2017-12-01

Recommender system becomes very popular and has important role in an information system or webpages nowadays. A recommender system tries to make a prediction of which item a user may like based on his activity on the system. There are some familiar techniques to build a recommender system, such as content-based filtering and collaborative filtering. Content-based filtering does not involve opinions from human to make the prediction, while collaborative filtering does, so collaborative filtering can predict more accurately. However, collaborative filtering cannot give prediction to items which have never been rated by any user. In order to cover the drawbacks of each approach with the advantages of other approach, both approaches can be combined with an approach known as hybrid technique. Hybrid technique used in this work is weighted technique in which the prediction score is combination linear of scores gained by techniques that are combined.The purpose of this work is to show how an approach of weighted hybrid technique combining content-based filtering and item-based collaborative filtering can work in a movie recommender system and to show the performance comparison when both approachare combined and when each approach works alone. There are three experiments done in this work, combining both techniques with different parameters. The result shows that the weighted hybrid technique that is done in this work does not really boost the performance up, but it helps to give prediction score for unrated movies that are impossible to be recommended by only using collaborative filtering.

Multi-Detector Computed Tomography Imaging Techniques in Arterial Injuries

Directory of Open Access Journals (Sweden)

Cameron Adler

2018-04-01

Full Text Available Cross-sectional imaging has become a critical aspect in the evaluation of arterial injuries. In particular, angiography using computed tomography (CT is the imaging of choice. A variety of techniques and options are available when evaluating for arterial injuries. Techniques involve contrast bolus, various phases of contrast enhancement, multiplanar reconstruction, volume rendering, and maximum intensity projection. After the images are rendered, a variety of features may be seen that diagnose the injury. This article provides a general overview of the techniques, important findings, and pitfalls in cross sectional imaging of arterial imaging, particularly in relation to computed tomography. In addition, the future directions of computed tomography, including a few techniques in the process of development, is also discussed.

Plasmapheresis and other extracorporeal filtration techniques in critical patients.

Science.gov (United States)

Daga Ruiz, D; Fonseca San Miguel, F; González de Molina, F J; Úbeda-Iglesias, A; Navas Pérez, A; Jannone Forés, R

2017-04-01

Plasmapheresis is an extracorporeal technique that eliminates macromolecules involved in pathological processes from plasma. A review is made of the technical aspects, main indications in critical care and potential complications of plasmapheresis, as well as of other extracorporeal filtration techniques such as endotoxin-removal columns and other devices designed to eliminate cytokines or modulate the inflammatory immune response in critical patients. Copyright © 2016 Elsevier España, S.L.U. y SEMICYUC. All rights reserved.

Analysis and analytical techniques

Energy Technology Data Exchange (ETDEWEB)

Batuecas Rodriguez, T [Department of Chemistry and Isotopes, Junta de Energia Nuclear, Madrid (Spain)

1967-01-01

The technology associated with the use of organic coolants in nuclear reactors depends to a large extent on the determination and control of their physical and chemical properties, and particularly on the viability, speed, sensitivity, precision and accuracy (depending on the intended usage) of the methods employed in detection and analytical determination. This has led to the study and development of numerous techniques, some specially designed for the extreme conditions involved in working with the types of product in question and others adapted from existing techniques. In the specific case of polyphenyl and hydropolyphenyl mixtures, which have been the principal subjects of study to date and offer greatest promise, the analytical problems are broadly as follows: Composition of initial product or virgin coolant composition of macro components and amounts of organic and inorganic impurities; Coolant during and after operation. Determination of gases and organic compounds produced by pyrolysis and radiolysis (degradation and polymerization products); Control of systems for purifying and regenerating the coolant after use. Dissolved pressurization gases; Detection of intermediate products during decomposition; these are generally very unstable (free radicals); Degree of fouling and film formation. Tests to determine potential formation of films; Corrosion of structural elements and canning materials; Health and safety. Toxicity, inflammability and impurities that can be activated. Although some of the above problems are closely interrelated and entail similar techniques, they vary as to degree of difficulty. Another question is the difficulty of distinguishing clearly between techniques for determining physical and physico-chemical properties, on one hand, and analytical techniques on the other. Any classification is therefore somewhat arbitrary (for example, in the case of dosimetry and techniques for determining mean molecular weights or electrical conductivity

Spatula scaffold: An iris-sparing technique for lensectomy.

Science.gov (United States)

Narang, Priya; Agarwal, Amar

2017-12-01

Lensectomy with vitrectomy is often performed for crystalline lenticular subluxation. We report a new technique and a practical approach that involves the placement of a spatula beneath the iris tissue that facilitates retroiridial removal of subluxated lens and acts as a scaffold by protecting the iris tissue from being accidentally trapped into the vitrectomy cutter port. Our technique facilitates management of the lens and vitreous without any trauma to the iris and secondarily obviates the need to perform an iris repair procedure that may arise due to iatrogenic reasons.

Esthetic rhinoplasty as an adjunctive technique in nasal oncoplastic ...

African Journals Online (AJOL)

Adham Farouk

2016-01-15

Jan 15, 2016 ... Esthetic rhinoplasty;. Oncoplastic surgery nose;. Basal cell carcinoma;. Squamous cell carcinoma;. Nonmelanoma skin cancer;. Nasal reconstruction ... Conclusions: Esthetic rhinoplasty is a useful adjunctive technique in nasal oncoplastic surgery. .... All procedures performed in the study involving human.

Principles for decisions involving environmental and health risks

International Nuclear Information System (INIS)

Bengtsson, B.

1989-01-01

Decision making with respect to safety is becoming more and more complex. The risk involved must be taken into account together with numerous other factors such as the benefits, the uncertainties and the public perception. Can the decision maker be aided by some kind of system, general rules of thumb, or broader perspective on similar decisions? This question has been addressed in a joint Nordic project relating to nuclear power. Modern techniques for risk assessment and management have been studied and parallels drawn to such areas as offshore safety and management of genotoxic chemicals in the environment. The topics include synoptic vs. incrementalistic approaches to decision making, health hazards from radiation and genotoxic chemicals, value judgments in decision making, definitions of low risks, risk comparisons, and principles for decision making when risks are involved. (author) 47 refs

Porous Structure Characterization in Titanium Coating for Surgical Implants

Directory of Open Access Journals (Sweden)

M.V. Oliveira

2002-09-01

Full Text Available Powder metallurgy techniques have been used to produce controlled porous structures, such as the porous coatings applied for dental and orthopedic surgical implants, which allow bony tissue ingrowth within the implant surface improving fixation. This work presents the processing and characterization of titanium porous coatings of different porosity levels, processed through powder metallurgy techniques. Pure titanium sponge powders were used for coating and Ti-6Al7Nb powder metallurgy rods were used as substrates. Characterization was made through quantitative metallographic image analysis using optical light microscope for coating porosity data and SEM analysis for evaluation of the coating/substrate interface integrity. The results allowed optimization of the processing parameters in order to obtain porous coatings that meet the requirements for use as implants.

Multiple sectioning and perforation techniques for TEM sub-surface studies

International Nuclear Information System (INIS)

Lee, E.H.; Rowcliffe, A.F.

1978-01-01

Techniques for preparing multiple electron transparent regions at several depth levels below the surface of a metal disk specimen are described. These techniques are relatively rapid and find application in many areas involving surface studies. Examples are shown of multiple thin areas produced at intervals of approximately 200 nm below the original surface of a stainless steel bombarded with 4 MeV Ni +2 ions for void swelling studies

Process Parameters Optimization for Friction Stir Welding of Pure Aluminium to Brass (CuZn30 using Taguchi Technique

Directory of Open Access Journals (Sweden)

Elfar O. M. R.

2016-01-01

Full Text Available In this research, the friction stir welding of dissimilar commercial pure aluminium and brass (CuZn30 plates was investigated and the process parameters were optimized using Taguchi L9 orthogonal array. The considered process parameters were the rotational speed, traverse speed and pin offset. The optimum setting was determined with reference to ultimate tensile strength of the joint. The predicted optimum value of ultimate tensile strength was confirmed by experimental run using optimum parameters. Analysis of variance revealed that traverse speed is the most significant factor in controlling the joint tensile strength and pin offset also plays a significant role. In this investigation, the optimum tensile strength is 50% of aluminium base metal. Metallographic examination revealed that intermetallic compounds were formed in the interface of the optimum joint where the tensile failure was observed to take place.

Identification of Fissionable Materials Using the Tagged Neutron Technique

International Nuclear Information System (INIS)

Keegan, R.P.; Hurley, J.P.; Tinsley, J.R.; Trainham, R.

2009-01-01

This summary describes experiments to detect and identify fissionable materials using the tagged neutron technique. The objective of this work is to enhance homeland security capability to find fissionable material that may be smuggled inside shipping boxes, containers, or vehicles. The technique distinguishes depleted uranium from lead, steel, and tungsten. Future work involves optimizing the technique to increase the count rate by many orders of magnitude and to build in the additional capability to image hidden fissionable materials. The tagged neutron approach is very different to other techniques based on neutron die-away or photo-fission. This work builds on the development of the Associated Particle Imaging (API) technique at the Special Technologies Laboratory (STL). Similar investigations have been performed by teams at the Oak Ridge National Laboratory (ORNL), the Khlopin Radium Institute in Russia, and by the EURITRACK collaboration in the European Union

Cross-sectional measurement of grain boundary segregation using WDS

Energy Technology Data Exchange (ETDEWEB)

Christien, F., E-mail: frederic.christien@emse.fr [Laboratoire Georges Friedel, CNRS, Ecole des Mines de Saint-Etienne, 158 Cours Fauriel, 42023 Saint-Etienne (France); Risch, P. [Institut des Matériaux Jean Rouxel (IMN), CNRS, Université de Nantes, Rue Christian Pauc, 44306 Nantes (France)

2016-11-15

A new method is proposed for the quantification of grain boundary segregation using Wavelength Dispersive Spectroscopy (WDS) in a Scanning Electron Microscope (SEM). Analyses are undertaken on a simple metallographically polished section of material. The method is demonstrated for the model system of sulphur segregation to nickel grain boundaries. Quantification was carried out from sulphur concentration profiles acquired across 11 grain boundaries of a nickel specimen containing 5.4 wt ppm of sulphur in the bulk and equilibrated at 550 °C. The average sulphur grain boundary concentration determined is µ=35.2 ng cm{sup −2}=6.6×10{sup 14} atoms cm{sup −2}≈0.5 monolayer, which is in good agreement with a previous quantification obtained from SIMS (Secondary Ion Mass Spectrometry) on the same material. However this is lower by a factor of two than the quantification obtained using “surface” techniques on fractured specimens of the same material. With the conditions of analysis used in this study, the limit of detection of the method developed is found to be better than 10% of a sulphur monolayer. - Highlights: • Impurity grain boundary segregation can be measured using WDS in a SEM. • The method proposed is quantitative. • The specimen preparation is simple: metallographical section.

In Situ Acoustic Monitoring of Thermal Spray Process Using High-Frequency Impulse Measurements

Science.gov (United States)

Tillmann, Wolfgang; Walther, Frank; Luo, Weifeng; Haack, Matthias; Nellesen, Jens; Knyazeva, Marina

2018-01-01

In order to guarantee their protective function, thermal spray coatings must be free from cracks, which expose the substrate surface to, e.g., corrosive media. Cracks in thermal spray coatings are usually formed because of tensile residual stresses. Most commonly, the crack occurrence is determined after the thermal spraying process by examination of metallographic cross sections of the coating. Recent efforts focus on in situ monitoring of crack formation by means of acoustic emission analysis. However, the acoustic signals related to crack propagation can be absorbed by the noise of the thermal spraying process. In this work, a high-frequency impulse measurement technique was applied to separate different acoustic sources by visualizing the characteristic signal of crack formation via quasi-real-time Fourier analysis. The investigations were carried out on a twin wire arc spraying process, utilizing FeCrBSi as a coating material. The impact of the process parameters on the acoustic emission spectrum was studied. Acoustic emission analysis enables to obtain global and integral information on the formed cracks. The coating morphology and coating defects were inspected using light microscopy on metallographic cross sections. Additionally, the resulting crack patterns were imaged in 3D by means of x-ray microtomography.

The use of crypto-analysis techniques for securing internet ...

African Journals Online (AJOL)

... recommended to be combined with other techniques, such as client-side software, data transaction protocols, web server software, and the network server operating system involved in handling e-commerce, for securing internet transaction. This recommendation will invariable ensure that internet transaction is secured.

Optimization of connection techniques for multipoint satellite videoconference

Science.gov (United States)

Perrone, A.; Puccio, A.; Tirro, S.

1985-12-01

Videoconferencing is increasingly considered a convenient substitute for business travels, and satellites will remain for a long time the most convenient means for quick network implementation. The paper gives indications about the most promising connection and demand assignment techniques, and defines a possible protocol for information exchange among involved entities.

Radiobiological Impact of Planning Techniques for Prostate Cancer ...

African Journals Online (AJOL)

... of RapidArc planning techniques for prostate cancer in terms of TCP and normal NTCP. Subjects and Methods: A computed tomography data set of ten cases involving low.risk prostate cancer was selected for this retrospective study. For each case, two RapidArc plans were created in Eclipse treatment planning system.

The construct of food involvement in behavioral research: scale development and validation.

Science.gov (United States)

Bell, Rick; Marshall, David W

2003-06-01

The construct of involvement has been found to influence brand loyalty, product information search processing, responses to advertising communications, diffusion of innovations, and ultimately, product choice decisions. Traditionally, involvement has been defined as being a characteristic of either a product or of an individual. In the present research, we make an assumption that an individual's 'food involvement' is a somewhat stable characteristic and we hypothesized that involvement with foods would vary between individuals, that individuals who are more highly involved with food would be better able to discriminate between a set of food samples than would less food involved individuals, and that this discrimination would operate both in affective and perceptive relative judgments. Using standard scale construction techniques, we developed a measure of the characteristic of food involvement, based on activities relating to food acquisition, preparation, cooking, eating and disposal. After several iterations, a final 12-item measure was found to have good test-retest reliability and internal consistency within two subscales. A behavioral validation study demonstrated that measures of food involvement were associated with discrimination and hedonic ratings for a range of foods in a laboratory setting. These findings suggest that food involvement, as measured by the Food Involvement Scale, may be an important mediator to consider when undertaking research with food and food habits.

Acoustic emission test on a 25mm thick mild steel pressure vessel with inserted defects

International Nuclear Information System (INIS)

Bentley, P.G.; Dawson, D.G.; Hanley, D.J.; Kirby, N.

1976-12-01

Acoustic emission measurements have been taken on an experimental mild steel vessel with 4 inserted defects ranging in severity up to 90% of through thickness. The vessel was subjected to a series of pressure excursions of increasing magnitude until failure occurred by extension of the largest inserted defect through the vessel wall. No acoustic emission was detected throughout any part of the tests which would indicate the presence of such serious defects or of impending failure. Measurements of acoustic emission from metallurgical specimens are included and the results of post test inspection using conventional NDT and metallographic techniques are reported. (author)

Phase transition temperature in the Zr-rich corner of Zr-Nb-Sn-Fe alloys

Science.gov (United States)

Canay, M.; Danón, C. A.; Arias, D.

2000-08-01

The influence of small composition changes on the phase transformation temperature of Zr-1Nb-1Sn-0.2(0.7)Fe alloys was studied in the present work, by electrical resistivity measurements and metallographic techniques. For the alloy with 0.2 at.% Fe we have determined Tα↔α+β=741°C and Tα+β↔β=973°C, and for the 0.7 at.% Fe the transformation temperatures were T α↔α+β=712°C and T α+β↔β=961°C. We have verified that the addition of Sn stabilized the β phase.

Comparative Analysis of Some Techniques in the Biological ...

African Journals Online (AJOL)

The experiments involved the simulation of conditions of a major spill by pouring crude oil on the cells from perforated cans and the in-situ bioremediation of the polluted soils using the techniques that consisted in the manipulation of different variables within the soil environment. The analysis of soil characteristics after a ...

The 'sniffer-patch' technique for detection of neurotransmitter release.

Science.gov (United States)

Allen, T G

1997-05-01

A wide variety of techniques have been employed for the detection and measurement of neurotransmitter release from biological preparations. Whilst many of these methods offer impressive levels of sensitivity, few are able to combine sensitivity with the necessary temporal and spatial resolution required to study quantal release from single cells. One detection method that is seeing a revival of interest and has the potential to fill this niche is the so-called 'sniffer-patch' technique. In this article, specific examples of the practical aspects of using this technique are discussed along with the procedures involved in calibrating these biosensors to extend their applications to provide quantitative, in addition to simple qualitative, measurements of quantal transmitter release.

Proton-beam technique dates fine wine

Science.gov (United States)

Dumé, Belle

2008-10-01

Nuclear physicists in France have invented a way to authenticate the vintage of rare wine without needing a sommelier's keen nose or even a corkscrew. The technique, which involves firing high-energy protons at wine bottles, can determine how old the bottles are and even where they come from. The new method could help unmask counterfeit wines - a growing problem in the fine-wine industry, where a bottle can sell for thousands of Euros.

Laboratory approaches of nuclear reactions involved in primordial and stellar nucleosynthesis

International Nuclear Information System (INIS)

Rolfs, C.; California Inst. of Tech., Pasadena

1986-01-01

Laboratory-based studies of primordial and stellar nucleosynthesis are reviewed, with emphasis on the nuclear reactions induced by charged particles. The analytical approach used to investigate nuclear reactions associated with stellar reactions is described, as well as the experimental details and procedures used to investigate nuclear reactions induced by charged particles. The present knowledge of some of the key reactions involved in primordial nucleosynthesis is discussed, along with the progress and problems of nuclear reactions involved in the hydrogen and helium burning phases of a star. Finally, a description is given of new experimental techniques which might be useful for future experiments in the field of nuclear astrophysics. (U.K.)

[Orbital decompression in Grave's disease: comparison of techniques].

Science.gov (United States)

Sellari-Franceschini, S; Berrettini, S; Forli, F; Bartalena, L; Marcocci, C; Tanda, M L; Nardi, M; Lepri, A; Pinchera, A

1999-12-01

Grave's ophthalmopathy is an inflammatory, autoimmune disorder often associated with Grave's disease. The inflammatory infiltration involves the retrobulbar fatty tissue and the extrinsic eye muscles, causing proptosis, extraocular muscle dysfunction and often diplopia. Orbital decompression is an effective treatment in such cases, particularly when resistant to drugs and external radiation therapy. This work compares the results of orbital decompression performed by removing: a) the medial and lateral walls (Mourits technique) in 10 patients (19 orbits) and b) the medial and lower walls (Walsh-Ogura technique) in 17 patients (31 orbits). The results show that removing the floor of the orbit enables better reduction of proptosis but more easily leads to post-operative diplopia. Thus it proves necessary to combine the two techniques, modifying the surgical approach on a case-by-case basis.

Survey on peripheral techniques of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru shuhen gijutsu no chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of survey on brown coal liquefaction techniques and peripheral techniques, centered by COSTEAM process under development in USA, solubilization by alcohol and liquefaction and cracking with the aid of tetrahydroquinoline as the hydrogen donor under development in Japan, and low-temperature carbonization and new promising techniques. The COSTEAM process shows higher reaction rates, conversions and oil yields for brown coal liquefaction than the one using hydrogen gas. Some of the problems involved in this process high viscosity and oxygenated compound content of the product oil. The product oil is acceptable as fuel for power generating plants and can be produced at a moderate cost, but may be unsuitable as vehicle fuel. Coal liquefaction and solubilization processes are mainly represented by those which use hydrogen. The hydrogen cost, which is high, determines the product price. The processes which use alcohol or tetrahydroquinoline are still in the experimental stage. (NEDO)

Gynecomastia Management: An Evolution and Refinement in Technique at UT Southwestern Medical Center

OpenAIRE

Bailey, Steven H.; Guenther, Dax; Constantine, Fadi; Rohrich, Rod J.

2016-01-01

Summary: Gynecomastia is a benign proliferation of male breast glandular tissue. Gynecomastia can affect men at any stage of life. Traditional treatment options involved excisional surgeries with periareolar or T-shaped scars, which can leave more visible scars on the chest. The technique presented represents a technique used by the senior author, which relies on ultrasonic liposuction and pull-through technique to remove breast tissue. A retrospective chart review was performed, including al...

Stakeholder Involvement in Decision Making: A Short Guide to Issues, Approaches and Resources

International Nuclear Information System (INIS)

2015-01-01

Radioactive waste management is embedded in broader societal issues such as the environment, risk management, energy, health policy and sustainability. In all these fields, there is an increasing demand for public involvement and engagement. This 2015 update of Stakeholder Involvement Techniques: Short Guide and Annotated Bibliography, assists practitioners and non-specialists by outlining the steps and issues associated with stakeholder involvement in decision making and by facilitating access to useful online resources (handbooks, toolboxes and case studies). The updated guide has been considerably enriched with experiences since 2004 and includes extensive references to the literature. It is published alongside the release of an online annotated bibliography that will be updated regularly. (authors)

EVALUATION OF THE METERED-DOSE INHALER TECHNIQUE AMONG HEALTHCARE PROVIDERS

Directory of Open Access Journals (Sweden)

E. Nadi F. Zeraati

2005-07-01

Full Text Available Poor inhaler technique is a common problem both in asthmatic patients and healthcare providers, which contributes to poor asthma control. This study was performed to evaluate the adequacy of metered-dose inhaler (MDI technique in a sample of physicians and nurses practicing in hospitals of Hamadan University of Medical Sciences. A total of 173 healthcare providers voluntary participated in this study. After the participants answered a questionnaire aimed at identifying their involvement in MDI prescribing and counseling, a trained observer assessed their MDI technique using a checklist of nine steps. Of the 173 participants, 35 (20.2% were physicians and 138 (79.8% were nurses. Only 12 participants (6.93% performed all steps correctly. Physicians performed essential steps significantly better than nurses (85.7% vs. 63.8%, P < 0.05. The majority of healthcare providers responsible for instructing patients on the correct MDI technique were unable to perform this technique correctly, indicating the need for regular formal training programs on inhaler techniques.

Application of the PRBS/FFT technique to digital simulations

International Nuclear Information System (INIS)

Hinds, H.W.

1977-01-01

This paper describes a method for obtaining a small-signal frequency response from a digital dynamic simulation. It employs a modified form of the PRBS/FFT technique, whereby a system is perturbed by a pseudo-random binary sequence and its response is analyzed using a fast Fourier transform-based program. Two applications of the technique are described; one involves a set of two coupled, second-order, ordinary differential equations; the other is a set of non-linear partial differential equations describing the thermohydraulic behaviour of water boiling in a fuel channel. (author)

Power-Cooling-Mismatch Test Series. Test PCM-2: postirradiation examination

International Nuclear Information System (INIS)

Seiffert, S.L.

1977-03-01

The report describes the results of the postirradiation examination of four 0.91-m long pressurized water reactor (PWR) type, UO 2 -fueled zircaloy-clad fuel rods tested in an in-pile experimental investigation of pre- and post-departure from nucleate boiling (DNB) behavior of previously unirradiated fuel rods. None of the four fuel rods tested failed during testing or during reactor shut down. Visual and metallographic examination of the individual fuel rods indicated that the length of the high temperature zone of film boiling varied from rod to rod. Two of the four fuel rods showed evidence of damage by film boiling, characterized by oxide spalling and cladding collapse. Metallographic examination of these fuel rods showed internal cladding oxidation resulting from fuel-cladding reaction. Cladding embrittlement by oxidation is evaluated. A comparison of the cladding surface temperatures estimated metallographically for the separate fuel rods with cladding surface temperatures measured during testing and calculated from the Fuel Rod Analysis Program-Transient (FRAP-T) computer code is included

Studies of some elementary processes involving electrons in the gas phase by pulse-radiolysis microwave-cavity technique

International Nuclear Information System (INIS)

Sunagawa, Takeyoshi; Makita, Takeshi; Musasa, Hirofumi; Tatsumi, Yoshitsugu; Shimamori, Hiroshi

1995-01-01

The pulse radiolysis-microwave cavity technique has been employed for detection of free electrons in the gas phase. Presented are results of the observation of electron disappearance by attachment to molecules, the electron thermalization (energy loss) processes in the presence of an electron-attaching compound, and the formation of electrons by Penning ionization. (author)

Application of the Lorentz-transform technique to meson photoproduction

International Nuclear Information System (INIS)

Reiss, C.; Leidemann, W.; Orlandini, G.; Tomusiak, E.L.

2003-01-01

We show that the Lorentz integral transform (LIT) technique which has been successfully applied to photoreactions in light nuclei can also be applied to photoreactions involving particle production. A simple model where results are easily calculable in the traditional fashion is used to test the technique. Specifically, we compute inclusive π + photoproduction from deuterium for photon energies less than 200 MeV using a Yamaguchi model for the NN interaction. It is demonstrated that, although the response functions for inclusive meson production do not have favourable asymptotic behavior, one can nonetheless extract them by inversion of the transform. The implication is that one can treat realistic problems of photo-meson production, including all final-state interactions, by means of the LIT technique. (orig.)

Modern techniques for studying biofilm-influenced corrosion

International Nuclear Information System (INIS)

Beech, I.B.

1998-01-01

In natural and made-made environments the presence of biofilms on surfaces of metals and their alloys influences electrochemistry at the biofilm/substratum interface, enhancing or inhibiting corrosion reactions. Due to the complexity of the biocorrosion phenomenon a range of techniques is commonly employed to study mechanisms involved. In addition to traditional methods of corrosion investigation such as electrochemical measurements and light and scanning electron microscopy observations coupled with energy dispersive X-ray analysis (EDXA) and X-ray diffraction (XRD). Modern techniques of surface science proved to be very useful in elucidating biofilm/metal interactions. Recent applications of Environmental Scanning Electron Microscopy (ESEM), Atomic Force Microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) to biocorrosion studies allowed better understanding of the biologically influenced metal deterioration process. The scope and promise of these latter techniques will be discussed and their use illustrated on practical examples. (Author)

Sonographic Screening for Abdominal Organ Involvement in Sickle Cell AnemiaA Step towards Better Patient Care

OpenAIRE

Bhushita B. Lakhkar; Bhushan N. Lakhkar; Bhavana B. Lakhkar

2017-01-01

Background: Sickle cell disease is characterized by repeated crisis and need for frequent transfusions. Abdominal crisis are common and potentially can damage any abdominal organ. Screening for organ involvement will lead to early detection and better patient care. Aim and Objectives: To see whether ultrasound can be a better noninvasive technique for early detection of organ involvement. Material and Methods: Prospective cross sectional observational study done on ...

Central localization of plasticity involved in appetitive conditioning in Lymnaea

OpenAIRE

Straub, Volko A.; Styles, Benjamin J.; Ireland, Julie S.; O'Shea, Michael; Benjamin, Paul R.

2004-01-01

Learning to associate a conditioned (CS) and unconditioned stimulus (US) results in changes in the processing of CS information. Here, we address directly the question whether chemical appetitive conditioning of Lymnaea feeding behavior involves changes in the peripheral and/or central processing of the CS by using extracellular recording techniques to monitor neuronal activity at two stages of the sensory processing pathway. Our data show that appetitive conditioning does not affect signific...

Management of excessive gingival display: Lip repositioning technique

Directory of Open Access Journals (Sweden)

Upasana Sthapak

2015-01-01

Full Text Available The lips form the frame of a smile and define the esthetic zone. Excessive gingival display during smile is often referred to as "gummy smile". A successful management of excessive gingival display with lip repositioning procedure has shown excellent results. The procedure involves removing a strip of partial thickness mucosa from maxillary vestibule, then suturing it back to the lip mucosa at the level of mucogingival junction. This technique results in restricted muscle pull and a narrow vestibule, thereby reducing the gingival display. In this case gummy smile was treated by modification of Rubinstein and Kostianovsky′s surgical lip repositioning technique which resulted in a harmonious smile.

New techniques for the treatment of uranium ores

International Nuclear Information System (INIS)

Renaud, J.; Boutonnet, G.

1977-01-01

The growth in nuclear power programmes since 1970 has led to an increasing demand for uranium, and tenders have been invited from all parts of the world for the construction of new treatment plants. What types of plant could be suggested. The diversity of ores and sites, even more stringent safety requirements, greater care for the environment and economic facts called for numerous, if not basic, reviews of the conventional techniques. Two examples illustrate this point. In the case of a plant to treat a refractory ore situated in a desert area with limited water resources, Pechiney Ugine Kuhlmann studied and applied a new technique of leaching by sulphuric acid pulping, which gives a considerable saving of sulphuric acid and water in comparison with conventional leaching techniques. In dealing with a problem which arose at a plant situated in a mountainous region of touristic interest, where a tailings settling tank could not be installed, Pechiney Ugine Kuhlmann studied and developed techniques involving the use of band filters for solid-liquid separation and pulp washing. Apart from lowering investment costs by about 15% in comparison with the techniques used so far, this technique produces the tailings in solid form so that they do not require a settling tank for storage. (author)

The hologram principles and techniques

CERN Document Server

Richardson, Martin J

2018-01-01

Written by Martin Richardson (an acclaimed leader and pioneer in the field) and John Wiltshire, The Hologram: Principles and Techniques is an important book that explores the various types of hologram in their multiple forms and explains how to create and apply the technology. The authors offer an insightful overview of the currently available recording materials, chemical formulas, and laser technology that includes the history of phase imaging and laser science. Accessible and comprehensive, the text contains a step-by-step guide to the production of holograms. In addition, The Hologram outlines the most common problems encountered in producing satisfactory images in the laboratory, as well as dealing with the wide range of optical and chemical techniques used in commercial holography. The Hologram is a well-designed instructive tool, involving three distinct disciplines: physics, chemistry, and graphic arts. This vital resource offers a guide to the development and understanding of the recording of mater...

The Role of External Involvement in the Creation of Management Innovations

DEFF Research Database (Denmark)

Mol, Michael J.; Birkinshaw, Julian

2014-01-01

There has recently been renewed scholarly interest in management innovating, the creation of new organizational practices, structures, processes and techniques. We suggest that external involvement in the process of management innovating can transpire in three different ways: direct input from...... no clear effect. Furthermore the three forms of involvement act to a large degree as substitutes. We contribute new theoretical arguments for the facilitators of management innovation, demonstrate the usefulness of an open innovation lens to the study of management innovation, show that management...... innovating is a relatively complex form of strategic process and highlight how the creation of management innovations is similar to and different from the genesis of other types of innovation....

CT reconstruction technique in lumbar intraneuroforaminal disc herniation

International Nuclear Information System (INIS)

Volle, E.; Claussen, C.; Kern, A.; Stoltenburg, G.

1988-01-01

The CT appearance of the lumbar neural foramina and contents is described in detail and compared to histopathological specimens. Direct axial scans with secondary sagittal, coronal and paraxial reconstruction series of slices of the neuralforamen were derived from lumbar spine examination of fifty normal adults. These normal parameters were then used to evaluate and subdivide 20 patients with disc herniation involving the neuralforamen. The new paraxial reformation was able to show an intraneuroforaminal disc involvement. CT-reformation technique and operative results in intraneuroforaminal disc herniation correspond in 80%. This improvement in preoperative diagnosis demonstrates to the neurosurgeon the full extent of disc herniation and results in an optimized operative approach. (orig.)

CT reconstruction technique in lumbar intraneuroforaminal disc herniation

Energy Technology Data Exchange (ETDEWEB)

Volle, E.; Claussen, C.; Kern, A.; Stoltenburg, G.

1988-04-01

The CT appearance of the lumbar neural foramina and contents is described in detail and compared to histopathological specimens. Direct axial scans with secondary sagittal, coronal and paraxial reconstruction series of slices of the neuralforamen were derived from lumbar spine examination of fifty normal adults. These normal parameters were then used to evaluate and subdivide 20 patients with disc herniation involving the neuralforamen. The new paraxial reformation was able to show an intraneuroforaminal disc involvement. CT-reformation technique and operative results in intraneuroforaminal disc herniation correspond in 80%. This improvement in preoperative diagnosis demonstrates to the neurosurgeon the full extent of disc herniation and results in an optimized operative approach.

Image processing techniques for remote sensing data

Digital Repository Service at National Institute of Oceanography (India)

RameshKumar, M.R.

interpretation and for processing of scene data for autonomous machine perception. The technique of digital image processing are used for' automatic character/pattern recognition, industrial robots for product assembly and inspection, military recognizance... and spatial co-ordinates into discrete components. The mathematical concepts involved are the sampling and transform theory. Two dimensional transforms are used for image enhancement, restoration, encoding and description too. The main objective of the image...

Electoral Proximity and the Political Involvement of Bureaucrats: A Natural Experiment in Argentina, 1904

Directory of Open Access Journals (Sweden)

Valentín Figueroa

2016-01-01

Full Text Available In this paper, I use a slightly modified version of the Becker–Stigler model of corrupt behavior to explain bureaucratic political involvement. Since bureaucrats prefer higher rewards and not to support losing candidates, we expect them to become politically involved near elections – when rewards are expected to be higher, and information more abundant. Taking advantage of a natural experiment, I employ differences-in-means and differences-in-differences techniques to esti-mate the effect of electoral proximity on the political involvement of justices of the peace in the city of Buenos Aires in 1904. I find a large, positive, and highly local effect of electoral proximity on their political involvement, with no appreciable impact in the months before or after elections.

Objective markers for upper motor neuron involvement in amyotrophic lateral sclerosis

International Nuclear Information System (INIS)

Iwata, Nobue K.

2007-01-01

A reliable objective marker of upper motor neuron (UMN) involvement is critical for early diagnosis and monitoring disease course in patients with amyotrophic lateral sclerosis (ALS). Lower motor neuron (LMN) involvement can be identified by electromyography, whereas UMN dysfunction has been currently distinguished solely by neurological examination. In the search for diagnostic tests to evaluate UMN involvement in ALS, numerous reports on new markers using neurophysiological and imaging techniques are accumulating. Transcranial magnetic stimulation evaluates the neurophysiological integrity of UMN. Although the diagnostic reliability and sensitivity of various parameters of central motor conduction measurement differ, central motor conduction time measurement using brainstem stimulation is potentially useful for determining UMN dysfunction by distinguishing lesions above the pyramidal decussation. MR-based techniques also have the potential to be used as diagnostic markers and are continuously improving as a modality to pursue early diagnosis and monitoring of the disease progression. Conventional MRI reveals hyperintensity along the corticospinal tract, hypointensity in the motor cortex, and atrophy of the precentral gyrus. There is a lack of agreement regarding sensitivity and specificity in detecting UMN abnormalities. Recent advances in magnetizing transfer imaging (MTI) provide more sensitive and accurate detection of corticospinal tract abnormality than conventional MRI. Reduction in N-acetyl-aspartate by proton magnetic spectroscopy in the motor cortex or the brainstem of the patients with ALS is reported with different techniques. Its diagnostic value in clinical assessment is uncertain and remains to be established. Diffusion tensor imaging (DTI) reveals the structural integrity of neuronal fibers, and has great diagnostic promise for ALS. It shows reduced diffusion anisotropy in the corticospinal tract with good correlation with physiological index

Potential impact of tsetse fly control involving the sterile insect technique

International Nuclear Information System (INIS)

Feldmann, U.; Dyck, V.A.; Mattioli, R.C.; Jannin, J.

2005-01-01

sterile insect technique (SIT), as a component of area-wide integrated pest management (AW-IPM) programmes to create tsetse-free zones, has been demonstrated in Zanzibar and other locations. This chapter (1) outlines the causal relationship between the T and T problem and food insecurity, malnutrition, poverty, and related disease and development constraints, (2) describes the impact of the problem on African rural communities and the overall economy, and (3) indicates the potential benefits of a reduced T and T burden, or even of its zonal elimination from selected priority areas in support of sustainable rural development. (author)

Coping with uncertainty in environmental impact assessments: Open techniques

Energy Technology Data Exchange (ETDEWEB)

Cardenas, Ibsen C., E-mail: c.cardenas@utwente.nl [IceBridge Research Institutea, Universiteit Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); Halman, Johannes I.M., E-mail: J.I.M.Halman@utwente.nl [Universiteit Twente, P.O. Box 217, 7500 AE Enschede (Netherlands)

2016-09-15

Uncertainty is virtually unavoidable in environmental impact assessments (EIAs). From the literature related to treating and managing uncertainty, we have identified specific techniques for coping with uncertainty in EIAs. Here, we have focused on basic steps in the decision-making process that take place within an EIA setting. More specifically, we have identified uncertainties involved in each decision-making step and discussed the extent to which these can be treated and managed in the context of an activity or project that may have environmental impacts. To further demonstrate the relevance of the techniques identified, we have examined the extent to which the EIA guidelines currently used in Colombia consider and provide guidance on managing the uncertainty involved in these assessments. Some points that should be considered in order to provide greater robustness in impact assessments in Colombia have been identified. These include the management of stakeholder values, the systematic generation of project options, and their associated impacts as well as the associated management actions, and the evaluation of uncertainties and assumptions. We believe that the relevant and specific techniques reported here can be a reference for future evaluations of other EIA guidelines in different countries. - Highlights: • uncertainty is unavoidable in environmental impact assessments, EIAs; • we have identified some open techniques to EIAs for treating and managing uncertainty in these assessments; • points for improvement that should be considered in order to provide greater robustness in EIAs in Colombia have been identified; • the paper provides substantiated a reference for possible examinations of EIAs guidelines in other countries.

Coping with uncertainty in environmental impact assessments: Open techniques

International Nuclear Information System (INIS)

Cardenas, Ibsen C.; Halman, Johannes I.M.

2016-01-01

Uncertainty is virtually unavoidable in environmental impact assessments (EIAs). From the literature related to treating and managing uncertainty, we have identified specific techniques for coping with uncertainty in EIAs. Here, we have focused on basic steps in the decision-making process that take place within an EIA setting. More specifically, we have identified uncertainties involved in each decision-making step and discussed the extent to which these can be treated and managed in the context of an activity or project that may have environmental impacts. To further demonstrate the relevance of the techniques identified, we have examined the extent to which the EIA guidelines currently used in Colombia consider and provide guidance on managing the uncertainty involved in these assessments. Some points that should be considered in order to provide greater robustness in impact assessments in Colombia have been identified. These include the management of stakeholder values, the systematic generation of project options, and their associated impacts as well as the associated management actions, and the evaluation of uncertainties and assumptions. We believe that the relevant and specific techniques reported here can be a reference for future evaluations of other EIA guidelines in different countries. - Highlights: • uncertainty is unavoidable in environmental impact assessments, EIAs; • we have identified some open techniques to EIAs for treating and managing uncertainty in these assessments; • points for improvement that should be considered in order to provide greater robustness in EIAs in Colombia have been identified; • the paper provides substantiated a reference for possible examinations of EIAs guidelines in other countries.

Braze Welding TIG of Titanium and Aluminium Alloy Type Al – Mg

Directory of Open Access Journals (Sweden)

Winiowski A.

2016-03-01

Full Text Available The article presents the course and the results of technological tests related to TIG-based arc braze welding of titanium and AW-5754 (AlMg3 aluminium alloy. The tests involved the use of an aluminium filler metal (Al99.5 and two filler metals based on Al-Si alloys (AlSi5 and AlSi12. Braze welded joints underwent tensile tests, metallographic examinations using a light microscope as well as structural examinations involving the use of a scanning electron microscope and an X-ray energy dispersive spectrometer (EDS. The highest strength and quality of welds was obtained when the Al99.5 filler metal was used in a braze welding process. The tests enabled the development of the most convenient braze welding conditions and parameters.

Effect of RE elements on the microstructural evolution of as cast and SIMA processed Mg-4Al alloy

International Nuclear Information System (INIS)

Nayyeri, Mohammad Javad; Khomamizadeh, Farzad

2011-01-01

Research highlights: → In this article, we examined the effect of Rare Earth elements on the microstructural development of as cast and semisolid Mg-4Al alloy produced by SIMA process. → Our investigations contained metallographic observation, scanning electron microscope and quantitative metallographic methods. → Results showed that alloy's dendrites turn into larger fully dendritic shape with sharp and narrow arms from equiaxed rosette type as the amount of RE elements increased from 0 through 4 percent. → Also we studied the effect of RE elements on the quality and quantityof intragranular liquid droplets as well as kinetic of microstructural changes. → Moreover, the effect of REs on the other parameters such as fraction of liquid, shape factor and particle size was studied.In this article, we examined the effect of Rare Earth elements on the microstructural development of as cast and semisolid Mg-4Al alloy produced by SIMA process. Our investigations contained metallographic observation, scanning electron microscope and quantitative metallographic methods. Results showed that alloy's dendrites turn into larger fully dendritic shape with sharp and narrow arms from equiaxed rosette type as the amount of RE elements increased from 0 through 4 percent. Also we studied the effect of RE elements on the quality and quantityof intragranular liquid droplets as well as kinetic of microstructural changes. Moreover, the effect of REs on the other parameters such as fraction of liquid, shape factor and particle size was studied. - Abstract: In the present article, the effect of Rare Earth elements on the microstructural development of as cast and semisolid Mg-4Al alloy produced by SIMA process is studied. Investigation conducted by metallographic observation, scanning electron microscope and quantitative metallographic methods. Results showed that alloy's dendrites turn into larger fully dendritic shape with sharp and narrow arms from equiaxed rosette type as the

A graphical simulator for teaching basic and advanced MR imaging techniques

DEFF Research Database (Denmark)

Hanson, Lars G

2007-01-01

Teaching of magnetic resonance (MR) imaging techniques typically involves considerable handwaving, literally, to explain concepts such as resonance, rotating frames, dephasing, refocusing, sequences, and imaging. A proper understanding of MR contrast and imaging techniques is crucial for radiolog...... be visualized in an intuitive way. The cross-platform software is primarily designed for use in lectures, but is also useful for self studies and student assignments. Movies available at http://radiographics.rsnajnls.org/cgi/content/full/e27/DC1 ....

Involving construction in the preliminary engineering process

International Nuclear Information System (INIS)

Mahoney, D.T. Jr.; Boccieri, S.V. Jr.

1994-01-01

With today's high cost associated with modifications in nuclear power plants, it is imperative that the authors continue to investigate ways to cut costs but at the same time improve efficiency and reduce radiation exposure to those directly associated with the implementation of modifications. The success associated with involving construction in the preliminary engineering process will not only cut costs and improve efficiency but will establish a Team Building concept to provide accountability to all those associated with the implementation of the task. This form of partnering focuses on the solutions rather than highlighting the difficulties. This paper will demonstrate techniques to implement such ideas and provide examples to corroborate actual successes already achieved

Assessing the Value of Structured Analytic Techniques in the U.S. Intelligence Community

Science.gov (United States)

2016-01-01

Analytic Techniques, and Why Do Analysts Use Them? SATs are methods of organizing and stimulating thinking about intelligence problems. These methods... thinking ; and imaginative thinking techniques encourage new perspectives, insights, and alternative scenarios. Among the many SATs in use today, the...more transparent, so that other analysts and customers can bet - ter understand how the judgments were reached. SATs also facilitate group involvement

Technical Papers on the Eighteen Metallographic Group Meeting

National Research Council Canada - National Science Library

Roman, H

1965-01-01

The polishing and etching procedures for preparing metallic, ceramic and cermet specimens of nuclear materials using the Automet polisher are discussed with some typical examples of the excellent results obtained...

Calculation of transformers leakage reactance using electromagnetic energy technique

International Nuclear Information System (INIS)

Feiz, J.; Mohseni, H.; Sabet Marzooghi, S.; Naderian Jahromi, A.

2004-01-01

Determination of transformer leakage reactance using magnetic cores has long been an area of interest to engineers involved in the design of power and distribution transformers. This is required for predicting the performance of transformers before actual assembly of the transformers. In this paper a closed form solution technique applicable to the leakage reactance calculations for transformers is presented. An emphasis is on the development of a simple method to calculate the leakage reactance of the distribution transformers and smaller transformers. Energy technique procedure for computing the leakage reactances in distribution transformers is presented. This method is very efficient compared with the use of flux element and image technique and is also remarkably accurate. Examples of calculated leakage inductances and the short circuit impedance are given for illustration. For validation, the results are compared with the results obtained using test. This paper presents a novel technique for calculation of the leakage inductance in different parts of the transformer using the electromagnetic stored energy

Radiation safety in industrial applications of nuclear techniques

International Nuclear Information System (INIS)

Lam, E.S.

1981-01-01

The hazards associated with the use of industrial equipment is one of the undesirable by-products of advanced technology. The use of nuclear techniques is a good example. Due to the usefulness of such techniques, one may accept the risks involved if they can be brought down to manageable levels. Most of the nuclear techniques in use in industries in Malaysia require only minimal safety precautions as they make use of only small amounts of radioactive material. However, some large sources are also being used and safety precautions have to be strictly enforced. The management plays a critical role in these industries. The requirements for radiation safety include the monitoring of workers and work areas, the medical surveillance of workers and the provision of barriers and other safety precautions. The management should also look to the training of the workers and be prepared for any emergencies that may arise. (author)

Radiation safety in industrial applications of nuclear techniques

Energy Technology Data Exchange (ETDEWEB)

Lam, E S [Ministry of Health, Kuala Lumpur (Malaysia)

1981-01-01

The hazards associated with the use of industrial equipment is one of the undesirable by-products of advanced technology. The use of nuclear techniques is a good example. Due to the usefulness of such techniques, one may accept the risks involved if they can be brought down to manageable levels. Most of the nuclear techniques in use in industries in Malaysia require only minimal safety precautions as they make use of only small amounts of radioactive material. However, some large sources are also being used and safety precautions have to be strictly enforced. The management plays a critical role in these industries. The requirements for radiation safety include the monitoring of workers and work areas, the medical surveillance of workers and the provision of barriers and other safety precautions. The management should also look to the training of the workers and be prepared for any emergencies that may arise.

Determination of hydrogen content in mixed oxide fuels (U,Pu)02 by three different methods: occluded gas, carrier gas at 9000C (apparatus Dupont de Nemours) and carrier gas at 17000C (apparatus Ithac 2000 Adamel). Operation, performance comparison of the three methods

International Nuclear Information System (INIS)

Lepetit; Lebrun; Haour; Dellasta; Vannier.

1989-01-01

Test conditions and performance are described. Results obtained allow a comparison and give the important parameters sampling conditions, sample storage and transfer, radiolysis and pyrohydrolysis. After a few hundred analysis fuels can be divided in two types: hydrogen content between 0.1 and 1 ppm corresponding to water fixation at the pellet surface, homogeneous content, not or slightly porous and with a perfect metallographic structure. Hydrogen content over 1 ppm, heterogeneous content from one sample to one another because of porosity and metallographic structure with cracks and cavities [fr

Electrolytic etching of uranium and of its alloys for examination under ordinary light

International Nuclear Information System (INIS)

Bouleau, M.

1958-12-01

The author reports a metallographic study of uranium and of some of its alloys (U-Mo with different Mo contents, U-Sn, U-Al) performed by using electrolytic etching. Samples are polished before being etched. Metallographic images are provided and results are briefly stated in terms of presence of grain boundaries, twins, platelets, pitting, metallic and non-metallic inclusions or eutectoid decomposition. The authors notice that, in some alloys with a gamma-stabilized structure, electrolytic etching allows an oxidation under reduced oxygen pressure, and then phase structure to be perfectly revealed

Decisions and involvement of cancer patient survivors: a moral imperative

Directory of Open Access Journals (Sweden)

Pravettoni G

2016-12-01

Full Text Available Gabriella Pravettoni,1,2 Ilaria Cutica,1,2 Simona Righetti,1 Ketti Mazzocco1,2 1Department of Oncology and Hematology, University of Milan, 2Applied Research Division for Cognitive and Psychological Science, European Institute of Oncology, Milan, Italy Purpose: The aim of this study was to review the experiences of direct involvement in patient survivorship for treatment and research. Methods: This is a narrative-focused review of the following two recent experiences of patient involvement: the Chordoma Foundation and the Triple Negative Breast Cancer Foundation. Results: These two examples represent concrete experiences that patients have built to favor a real involvement in the care and treatment of tumors. These experiences are profoundly modifying how cancer research is conducted and draw attention to the psychosocial dimensions of health care. Conclusion: These examples represent the new scenario in which modern medicine faces completely new challenges, copes with new needs, and cooperates with new health care professionals. Implications: Involving patients in a new perspective raises practical and ethical challenges for organizations to work together, for health providers to be professionally skilled and for the government to promote safeguarding policies. Keywords: patient empowerment, patients’ association, empowerment, skills, codesign ­techniques, cancer

The concept and evolution of involved site radiation therapy for lymphoma

DEFF Research Database (Denmark)

Specht, Lena; Yahalom, Joachim

2015-01-01

We describe the development of radiation therapy for lymphoma from extended field radiotherapy of the past to modern conformal treatment with involved site radiation therapy based on advanced imaging, three-dimensional treatment planning and advanced treatment delivery techniques. Today, radiation...... therapy is part of the multimodality treatment of lymphoma, and the irradiated tissue volume is much smaller than before, leading to highly significant reductions in the risks of long-term complications....

Public Involvement in Repository Site Selection for Nuclear Waste: Towards a more Dynamic View in Decision-Making Processes

Energy Technology Data Exchange (ETDEWEB)

Kruetli, Pius; Stauffacher, Michael; Flueeler, Thomas; Scholz, Roland W. [ETH Zuerich (Switzerland). lnst. for Human-Environment Systems (HES)

2006-09-15

This paper discusses possibilities of public involvement in radioactive waste management. A general overview of the radioactive waste issue is presented referring to a proposed model of the respective decision-making process. Based on the well known participation ladder by Arnstein, we differentiate various intensities of public involvement. A matrix with public involvement and the decision-making process is introduced and three prototypical patterns are discussed. We conclude that time frame, the level of public involvement and the mission have to be considered as well as techniques and the overarching context - all in all, a systematic and dynamic approach for public involvement is needed.

Public Involvement in Repository Site Selection for Nuclear Waste: Towards a more Dynamic View in Decision-Making Processes

International Nuclear Information System (INIS)

Kruetli, Pius; Stauffacher, Michael; Flueeler, Thomas; Scholz, Roland W.

2006-01-01

This paper discusses possibilities of public involvement in radioactive waste management. A general overview of the radioactive waste issue is presented referring to a proposed model of the respective decision-making process. Based on the well known participation ladder by Arnstein, we differentiate various intensities of public involvement. A matrix with public involvement and the decision-making process is introduced and three prototypical patterns are discussed. We conclude that time frame, the level of public involvement and the mission have to be considered as well as techniques and the overarching context - all in all, a systematic and dynamic approach for public involvement is needed

Airflow measurement techniques applied to radon mitigation problems

International Nuclear Information System (INIS)

Harrje, D.T.; Gadsby, K.J.

1989-01-01

During the past decade a multitude of diagnostic procedures associated with the evaluation of air infiltration and air leakage sites have been developed. The spirit of international cooperation and exchange of ideas within the AIC-AIVC conferences has greatly facilitated the adoption and use of these measurement techniques in the countries participating in Annex V. But wide application of such diagnostic methods are not limited to air infiltration alone. The subject of this paper concerns the ways to evaluate and improve radon reduction in buildings using diagnostic methods directly related to developments familiar to the AIVC. Radon problems are certainly not unique to the United States, and the methods described here have to a degree been applied by researchers of other countries faced with similar problems. The radon problem involves more than a harmful pollutant of the living spaces of our buildings -- it also involves energy to operate radon removal equipment and the loss of interior conditioned air as a direct result. The techniques used for air infiltration evaluation will be shown to be very useful in dealing with the radon mitigation challenge. 10 refs., 7 figs., 1 tab

Comprehension of Action Negation Involves Inhibitory Simulation

Directory of Open Access Journals (Sweden)

Francesco eForoni

2013-05-01

Full Text Available Previous research suggests that action language is comprehended by activating the motor system. We report a study, investigating a critical question in this research field: Do negative sentences activate the motor system? Participants were exposed to sentences in the affirmation and negation forms while the zygomatic muscle activity on the left side of the face was continuously measured (Electromyography technique: EMG. Sentences were descriptions of emotional expressions that mapped either directly upon the zygomatic muscle (e.g., ‘I am smiling’ or did not (e.g., ‘I am frowning’. Reading sentences involving the negation of the activity of a specific muscle (zygomatic major - I am not smiling is shown to lead to the inhibition of this muscle. Reading sentences involving the affirmative form instead (I am smiling leads to the activation of zygomatic mucle. In contrast, sentences describing an activity that is irrelevant to the zygomatic muscle (e.g., ‘I am frowning’ or ‘I am not frowning’ produce no muscle activity. These results extend the range of simulation models to negation and by implication to an abstract domain. We discuss how this research contributes to the grounding of abstract and concrete concepts.

Justification of novel practices involving radiation exposure

International Nuclear Information System (INIS)

Webb, G.; Boal, T.; Mason, C.; Wrixon, T.

2006-01-01

The concept of 'justification' of practices has been one of the three basic principles of radiation protection for many decades. The principle is simple in essence - that any practice involving radiation exposure should do more good than harm. There is no doubt that the many uses of radiation in the medical field and in industry generally satisfy this principle, yielding benefits that could not be achieved using other techniques; examples include CT scanning and industrial radiography. However, even in the early period after the introduction of the justification principle, there were practices for which the decision on justification was not clear and for which different decisions were made by the authorities in different countries. Many of these involved consumer products such as luminous clocks and watches, telephone dials, smoke detectors, lightning preventers and gas mantles. In most cases, these practices were relatively small scale and did not involve large exposures of either individual workers or members of the public. Decisions on justification were therefore often made by the regulator without extensive national debate. Over recent years, several practices have been proposed and undertaken that involve exposure to radiation for purposes that were generally not envisaged when the current system of radiation protection was created. Some of these practices were reviewed during a recent symposium held in Dublin, Ireland and involve, for example, the x-raying of people for theft detection purposes, for detection of weapons or contraband, for the prediction of physical development of young athletes or dancers, for age determination, for insurance purposes and in cases of suspected child abuse. It is particularly in the context of such novel practices that the need has emerged for clearer international guidance on the application of the justification principle. This paper reviews recent activities of the IAEA with respect to these issues, including the

Justification of novel practices involving radiation exposure

Energy Technology Data Exchange (ETDEWEB)

Webb, G. [Radiation Protection Consul tant, Brighton (United Kingdom); Boal, T.; Mason, C.; Wrixon, T. [International Atomic Energy Agency, Vienna (Austria)

2006-07-01

The concept of 'justification' of practices has been one of the three basic principles of radiation protection for many decades. The principle is simple in essence - that any practice involving radiation exposure should do more good than harm. There is no doubt that the many uses of radiation in the medical field and in industry generally satisfy this principle, yielding benefits that could not be achieved using other techniques; examples include CT scanning and industrial radiography. However, even in the early period after the introduction of the justification principle, there were practices for which the decision on justification was not clear and for which different decisions were made by the authorities in different countries. Many of these involved consumer products such as luminous clocks and watches, telephone dials, smoke detectors, lightning preventers and gas mantles. In most cases, these practices were relatively small scale and did not involve large exposures of either individual workers or members of the public. Decisions on justification were therefore often made by the regulator without extensive national debate. Over recent years, several practices have been proposed and undertaken that involve exposure to radiation for purposes that were generally not envisaged when the current system of radiation protection was created. Some of these practices were reviewed during a recent symposium held in Dublin, Ireland and involve, for example, the x-raying of people for theft detection purposes, for detection of weapons or contraband, for the prediction of physical development of young athletes or dancers, for age determination, for insurance purposes and in cases of suspected child abuse. It is particularly in the context of such novel practices that the need has emerged for clearer international guidance on the application of the justification principle. This paper reviews recent activities of the IAEA with respect to these issues, including the

Tubular foreign body or stent: safe retrieval or repositioning using the coaxial snare technique

International Nuclear Information System (INIS)

Seong, Chang Kyu; Kim, Yong Joo; Chung, Jin Wook; Kim, Seung Hyup; Han, Joon Koo; Kim, Hyun Beom; Park, Jae Hyung

2002-01-01

To evaluate the utility and advantages of the coaxial snare technique in the retrieval of tubular foreign bodies. Using the coaxial snare technique, we attempted to retrieve tubular foreign bodies present in seven patients. The bodies were either stents which were malpositioned or had migrated from their correct position in the vascular system (n=2), a fragmented venous introducer sheath (n=1), fragmented drainage catheters in the biliary tree (n=2), or fractured external drainage catheters in the urinary tract (n=2). After passing a guidewire and/or a dilator through the lumina of these foreign bodies, we introduced a loop snare over the guidewire or dilator, thus capturing and retrieving them. In all cases, it was possible to retrieve or reposition the various items, using a minimum-sized introducer sheath or a tract. No folding was involved. In no case were surgical procedures required, and no complications were encountered. The coaxial snare technique, an application of the loop snare technique, is a useful and safe method for the retrieval of tubular foreign bodies, and one which involves minimal injury to the patient

Assessment of precipitates of isothermal aged austenitic stainless steel using measurement techniques of ultrasonic attenuation

International Nuclear Information System (INIS)

Kim, Hun Hee; Kim, Hak Joon; Song, Sung Jin; Lim, Byeong Soo; Kim, Kyung Cho

2014-01-01

AISI 316L stainless steel is widely used as a structural material of high temperature thermoelectric power plants, since austenitic stainless steel has excellent mechanical properties. However, creep damage is generated in these components, which are operated under a high temperature and high pressure environment. Several researches have been done on how microstructural changes of precipitates affect to the macroscopic mechanical properties. And they investigate the relation between ultrasonic parameters and metallurgical results. But, these studies are limited by experiment results only. In this paper, attenuations of ultrasonic with isothermal damaged AISI 316L stainless steel were measured. Also, simulation of ultrasonic attenuation with variation of area fraction and size of precipitates were performed. And, from the measured attenuations, metallographic data and simulation results, we investigate the relations between the ultrasonic attenuations and the material properties which is area fraction of precipitates for the isothermal damaged austenitic stainless steel specimens. And, we studied parametric study for investigation of the relation between ultrasonic parameters and metallurgical results of the isothermal damaged AISI 316L stainless steel specimens using numerical methods.

Nuclear medicine techniques in the assessment of alkaptonuria.

Science.gov (United States)

Vinjamuri, Sobhan; Ramesh, Chandakacharla N; Jarvis, Jonathan; Gallagher, Jim A; Ranganath, Lakshminarayana L

2011-10-01

Alkaptonuria is a rare autosomal recessive disorder due to a lack of the enzyme homogentisate dioxygenase, leading to ochronosis, a process of accumulation of a melanin-like polymer of homogentisic acid in cartilage and other collagenous structures. Patients develop severe osteoarthropathy that resembles osteoarthritis. Although the diagnosis of alkaptonuria is not particularly challenging in view of the blue-black discolouration of visible connective tissue and the presence of homogentisic acid in urine, the natural history of alkaptonuria remains poorly understood. Patients would benefit immensely from an objective assessment of their disease status and from a clearer understanding of the pathophysiology and associated physical changes. Isotope bone scans, which are commonly used to identify the extent of involvement of bones in cancerous processes, have also been increasingly used for characterizing the extent of arthropathy in conditions such as osteoarthritis and rheumatoid arthritis. Semiquantitative scores based on the extent of involvement of joints have been used to describe the involvement of large joints in the context of symptomatic treatment for osteoarthritis. A similar semiquantitative isotope bone scan score depending on the involvement of the number of large joints in patients with alkaptonuria can be formulated and validated in a suitable cohort of patients. Bone densitometry measurement using dual-energy X-ray absorptiometry scanning is an internationally accepted tool to assess the risk and extent of osteoporosis, and is increasingly used to assess the additional fracture risk in patients with arthropathy. We believe that, currently, nuclear medicine techniques can provide useful information, which can be incorporated into disease severity scores for alkaptonuria. Once the biological basis for alkaptonuria is better understood, it is feasible that nuclear medicine techniques of even greater sensitivity and specificity can be developed, thereby

Sonographic Screening for Abdominal Organ Involvement in Sickle Cell AnemiaA Step towards Better Patient Care

Directory of Open Access Journals (Sweden)

Bhushita B. Lakhkar

2017-04-01

Full Text Available Background: Sickle cell disease is characterized by repeated crisis and need for frequent transfusions. Abdominal crisis are common and potentially can damage any abdominal organ. Screening for organ involvement will lead to early detection and better patient care. Aim and Objectives: To see whether ultrasound can be a better noninvasive technique for early detection of organ involvement. Material and Methods: Prospective cross sectional observational study done on patients admitted in pediatric ward of a medical college. Total of 150 patients, already diagnosed to have sickle cell anemia (homozygous 110 and heterozygous 40 was included in the study. All the patients were in steady state. Demographic, clinical biochemical details were noted and were subjected to ultrasonography. Renal artery, Being end artery, Doppler study was also done. All the modalities were compared for early detection. Results: Majority of patients (77% were between 1 to 30 years with male female ratio of 2:1. Recurrent fever (64% and recurrent abdominal pain (47% were most common symptoms and anemia (66%, hepatomegaly (62%, splenomegaly (21% were most common signs. When clinical examination, biochemical tests and ultrasonography were compared for organ detection, ultrasound significantly detected more patients (p=<0.05. Ultrasonography of kidney included renal doppler also. Renal involvement by microalbuminuria measurement was of same as ultrasonography. Organ involvement increased with age. Conclusion: Ultrasonography was good noninvasive technique for organ detection but kidneysyield was better with Doppler study. Most common organ found to be affected was liver. Involvement increased with age. Early detection helps clinicians to avoid drugs toxic to involved organs.

Rectal cancer: involved circumferential resection margin - a root cause analysis.

Science.gov (United States)

Youssef, H; Collantes, E C; Rashid, S H; Wong, L S; Baragwanath, P

2009-06-01

An involved circumferential resection margin (CRM) following surgery for rectal cancer is the strongest predictor of local recurrence and may represent a failure of the multidisciplinary team (MDT) process. The study analyses the causes of positive CRM in patients undergoing elective surgery for rectal cancer with respect to the decision-making process of the MDT, preoperative rectal cancer staging and surgical technique. From March 2002 to September 2005, data were collected prospectively on all patients undergoing elective rectal cancer surgery with curative intent. The data on all patients identified with positive CRM were analysed. Of 158 patients (male:female = 2.2:1) who underwent potentially curative surgery, 16 (10%) patients had a positive CRM on postoperative histology. Four were due to failure of the pelvic magnetic resonance imaging (MRI) staging scans to predict an involved margin, two with an equivocal CRM on MRI did not have preoperative radiotherapy, one had an inaccurate assessment of the site of primary tumour and in one intra-operative difficulty was encountered. No failure of staging or surgery was identified in the remaining eight of the 16 patients. Abdominoperineal resection (APR) was associated with a 26% positive CRM, compared with 5% for anterior resection. No single consistent cause was found for a positive CRM. The current MDT process and/or surgical technique may be inadequate for low rectal tumours requiring APR.

Stakeholder Involvement Throughout the Life Cycle of Nuclear Facilities

International Nuclear Information System (INIS)

2011-01-01

stakeholder involvement techniques and introducing messages such as ethical issues in support of nuclear facilities, including the need for sustainable energy resources and responsibility to future generations. The printed version of the report does not include examples. Instead, the Nuclear Communicator's Toolbox (http://www.iaea.org/nuccomtoolbox/index.html) will store good practices and lessons learnt that can be accessible to all readers and will be updated on a regular basis based on the new case studies that are submitted by users to the following email address: toolbox(at)iaea.org.

Using the critical incident technique in community-based participatory research: a case study.

Science.gov (United States)

Belkora, Jeffrey; Stupar, Lauren; O'Donnell, Sara

2011-01-01

Successful community-based participatory research involves the community partner in every step of the research process. The primary study for this paper took place in rural, Northern California. Collaborative partners included an academic researcher and two community based resource centers that provide supportive services to people diagnosed with cancer. This paper describes our use of the Critical Incident Technique (CIT) to conduct Community-based Participatory Research. We ask: Did the CIT facilitate or impede the active engagement of the community in all steps of the study process? We identified factors about the Critical Incident Technique that were either barriers or facilitators to involving the community partner in every step of the research process. Facilitators included the CIT's ability to accommodate involvement from a large spectrum of the community, its flexible design, and its personal approach. Barriers to community engagement included training required to conduct interviews, depth of interview probes, and time required. Overall, our academic-community partners felt that our use of the CIT facilitated community involvement in our Community-Based Participatory Research Project, where we used it to formally document the forces promoting and inhibiting successful achievement of community aims.

Comparative studies on ultrasonic, friction, laser and resistance pressure welding of NiTi shape memory alloys with high-alloy steels. Final report; Vergleichende Untersuchungen zum Ultraschall-, Reib-, Laserstrahl- und Widerstandspressschweissen von NiTi-Shape-Memory-Metall mit hochlegierten Staehlen. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Zuckschwerdt, K.

2000-04-01

The suitability of different welding techniques for welding of NiTi shape memory alloys with high-alloy steel (C12CrNi17-7, X5CrNiNb19-9, X20Cr13) was investigated. The quality of the welds was analyzed using mechanical-technological, fractographic, metallographic and electron microscopy analysis. [German] Ziel dieses Forschungsvorhabens ist es, die Eignung der einzelnen Schweissverfahren fuer das Fuegen von NiTi-Formgedaechtnislegierungen mit hochlegiertem Stahl (X12CrNi17-7, X5CrNiNb19-9, X20Cr13) darzustellen und zu beurteilen. Die Qualitaet der Fuegeverbindungen wird mit Hilfe mechanisch-technologischer, fraktographischer, metallographischer und elektronenmikroskopischer Untersuchungen bewertet.

Contribution to the grain refinement of hypoeutectic aluminium-silicon casting alloys: application of a new grain refiner and experience from practice; Beitrag zur Kornfeinung von untereutektischen Aluminium-Silicium-Gusslegierungen: Anwendung eines neuen Kornfeiners und Erfahrungen aus der Praxis

Energy Technology Data Exchange (ETDEWEB)

Koch, H. [Aluminium Rheinfelden GmbH, Rheinfelden (Germany)

2000-10-01

This paper describes the application of a master alloy on the basis of aluminium-titanium-boron, that is designed for hypoeutectic aluminium-silicon casting alloys. The efficiency of the grain refiner was measured using thermal analysis and sand and permanent mould casted samples. The grain size was measured using metallographic technique. In addition, casting trials using a spiral sand mould were carried out to estimate the influence on the flowing behaviour of the melt. To compare the results, a standard AlTi5B1 rod was used under the same test conditions. Finally, results from practice are shown. The grain refinement mechanism is discussed. (orig.)

Manufacturing tungsten monocrystal tubes by electro-spark machining and study of machined surface structure

International Nuclear Information System (INIS)

Abdukarimov, Eh.T.; Ismailov, L.R.; Krakhmalev, V.A.; Fershtat, L.N.

1981-01-01

A technique to manufacture tubes from tungsten monocrystals with low consumption of electrodes has been developed. Regimes of obtaining deep and through holes of different diameters with the productivity of 1 mm/min and with the minimum deviation from cylindrical shape are worked out using a specially designed electric pulse installation. X-ray and metallographical analyses have shown that as a result of electrospark machining a cold hardened layer is formed up to hundreds micrometers thick, pierced by the network of microcracks. Simultaneous use of electrospark and electrochemical machining permitted to manufacture tubes from tungsten monocrystals with non-distorted monocrystal surface and without a network of microcracks

A facial reconstruction and identification technique for seriously devastating head wounds.

Science.gov (United States)

Joukal, Marek; Frišhons, Jan

2015-07-01

Many authors have focused on facial identification techniques, and facial reconstructions for cases when skulls have been found are especially well known. However, a standardized facial identification technique for an unknown body with seriously devastating head injuries has not yet been developed. A reconstruction and identification technique was used in 7 cases of accidents involving trains striking pedestrians. This identification technique is based on the removal of skull bone fragments, subsequent fixation of soft tissue onto a universal commercial polystyrene head model, precise suture of dermatomuscular flaps, and definitive adjustment using cosmetic treatments. After reconstruction, identifying marks such as scars, eyebrows, facial lines, facial hair and partly hairstyle become evident. It is then possible to present a modified picture of the reconstructed face to relatives. After comparing the results with photos of the person before death, this technique has proven to be very useful for identifying unknown bodies when other identification techniques are not available. This technique is useful for its being rather quick and especially for its results. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Dissimilar steel welding and overlay covering with nickel based alloys using SWAM (Shielded Metal Arc Welding) and GTAW (Gas Tungsten Arc Welding) processes in the nuclear industry

Energy Technology Data Exchange (ETDEWEB)

Arce Chilque, Angel Rafael [Centro Tecnico de Engenharia e Inovacao Empresarial Ltda., Belo Horizonte, MG (Brazil); Bracarense, Alexander Queiroz; Lima, Luciana Iglesias Lourenco [Federal University of Minas Gerais (UFMG), Belo Horizonte, MG (Brazil); Quinan, Marco Antonio Dutra; Schvartzman, Monica Maria de Abreu Mendonca [Nuclear Technology Development Centre (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Marconi, Guilherme [Federal Center of Technological Education (CEFET-MG), Belo Horizonte, MG (Brazil)

2009-07-01

This work presents the welding of dissimilar ferritic steel type A508 class 3 and austenitic stainless steel type AISI 316 L using Inconel{sup R} 600 (A182 and A82) and overlay covering with Inconel{sup R} 690 (A52) as filler metal. Dissimilar welds with these materials without defects and weldability problems such as hot, cold, reheat cracking and Ductility Dip Crack were obtained. Comparables mechanical properties to those of the base metal were found and signalized the efficiency of the welding procedure and thermal treatment selected and used. This study evidences the importance of meeting compromised properties between heat affected zone of the ferritic steel and the others regions presents in the dissimilar joint, to elaborate the dissimilar metal welding procedure specification and weld overlay. Metallographic studies with optical microscopy and Vickers microhardness were carried out to justified and support the results, showing the efficiency of the technique of elaboration of dissimilar metal welding procedure and overlay. The results are comparables and coherent with the results found by others. Some alternatives of welding procedures are proposed to attain the efficacy. Further studies are proposed like as metallographic studies of the fine microstructure, making use, for example, of scanning electron microscope (SEM adapted with an EDS) to explain looking to increase the resistance to primary water stress corrosion (PWSCC) in nuclear equipment. (author)

A new techniques in the physics of diagnostic radiology

International Nuclear Information System (INIS)

Jennings, R.J.

1987-01-01

The basic physics involved in the generation of X-rays and in the energy dependence of their interaction with matter are reviewed. Some applications of those ideas in both conventional X-ray imaging and in new imaging techniques are studied. Methods for the optimization of X-ray diagnostic imaging system are discussed. (M.A.C.) [pt

Cut-it-out technique for ocular fish-hook injury.

Science.gov (United States)

Ahmad, Syed Shoeb; Seng, Chiang Wai; Ghani, Shuaibah Abdul; Lee, Jane F

2013-10-01

An 11-year-old boy was involved in an injury with a fish-hook to his eye. The hook had impaled itself to the cornea and deeper structures. There was associated corneal edema and hyphema, making visualization difficult. In this case, we performed the unusual "cut-it-out" technique to remove the hook from the eye.

Cut-it-out technique for ocular fish-hook injury

Directory of Open Access Journals (Sweden)

Syed Shoeb Ahmad

2013-01-01

Full Text Available An 11-year-old boy was involved in an injury with a fish-hook to his eye. The hook had impaled itself to the cornea and deeper structures. There was associated corneal edema and hyphema, making visualization difficult. In this case, we performed the unusual "cut-it-out" technique to remove the hook from the eye.

Cut-it-out technique for ocular fish-hook injury

OpenAIRE

Ahmad, Syed Shoeb; Seng, Chiang Wai; Ghani, Shuaibah Abdul; Lee, Jane F

2013-01-01

An 11-year-old boy was involved in an injury with a fish-hook to his eye. The hook had impaled itself to the cornea and deeper structures. There was associated corneal edema and hyphema, making visualization difficult. In this case, we performed the unusual "cut-it-out" technique to remove the hook from the eye.

Endoscopic ultrasonography-guided pancreatic duct access: techniques and literature review of pancreatography, transmural drainage and rendezvous techniques.

Science.gov (United States)

Itoi, Takao; Kasuya, Kazuhiko; Sofuni, Atsushi; Itokawa, Fumihide; Kurihara, Toshio; Yasuda, Ichiro; Nakai, Yousuke; Isayama, Hiroyuki; Moriyasu, Fuminori

2013-05-01

Endoscopic ultrasonography-guided (EUS)-guided pancreatic interventions have gained increasing attention. Here we review EUS-guided pancreatic duct (PD) access techniques and outcomes. EUS-guided PD intervention is divided into two types, antegrade and rendezvous techniques, following EUS-guided pancreatography. In the antegrade technique, pancreaticoenterostomy is carried out by stent placement between the PD and the stomach, duodenum, or jejunum. Transenteric antegrade PD stenting is conducted by stent placement, advancing anteriorly into the PD through the pancreatic tract. The rendezvous technique is carried out by using a guidewire through the papilla or anastomotic site for retrograde stent insertion. In terms of EUS-guided PD stenting, 11 case reports totaling 75 patients (35 normal anatomy, 40 altered anatomy) have been published. The technical success rate was greater than 70%. Early adverse events, including severe hematoma and severe pancreatitis,occurred in seven (63.6%) of 11 reports. Regarding the rendezvous technique, 12 case reports totaling 52 patients (22 normal anatomy, 30 altered anatomy) have been published. The technical success rate ranged from 25% to 100%. It was 48% in one report that involved more than 20 cases. Once stents were placed, all patients became free of symptoms. Early mild adverse events occurred in four (36.4%) of 11 reports. In conclusion, although it can be risky because of possible serious or even fatal adverse events, including pancreatic juice leakage, perforation and severe acute pancreatitis, EUS-PD access seems to be promising for treating symptomatic pancreatic diseases caused by PD stricture and pancreaticoenterostomy stricture. © 2013 The Authors. Digestive Endoscopy © 2013 Japan Gastroenterological Endoscopy Society.

[Progress of Masquelet technique to repair bone defect].

Science.gov (United States)

Yin, Qudong; Sun, Zhenzhong; Gu, Sanjun

2013-10-01

To summarize the progress of Masquelet technique to repair bone defect. The recent literature concerning the application of Masquelet technique to repair bone defect was extensively reviewed and summarized. Masquelet technique involves a two-step procedure. First, bone cement is used to fill the bone defect after a thorough debridement, and an induced membrane structure surrounding the spacer formed; then the bone cement is removed after 6-8 weeks, and rich cancellous bone is implanted into the induced membrane. Massive cortical bone defect is repaired by new bone forming and consolidation. Experiments show that the induced membrane has vascular system and is also rich in vascular endothelial growth factor, transforming growth factor beta1, bone morphogenetic protein 2, and bone progenitor cells, so it has osteoinductive property; satisfactory results have been achieved in clinical application of almost all parts of defects, various types of bone defect and massive defect up to 25 cm long. Compared with other repair methods, Masquelet technique has the advantages of reliable effect, easy to operate, few complications, low requirements for recipient site, and wide application. Masquelet technique is an effective method to repair bone defect and is suitable for various types of bone defect, especially for bone defects caused by infection and tumor resection.

Transcranial magnetic stimulation techniques in clinical investigation.

Science.gov (United States)

Currà, A; Modugno, N; Inghilleri, M; Manfredi, M; Hallett, M; Berardelli, A

2002-12-24

Transcranial magnetic stimulation (TMS) is a technique that can activate cortical motor areas and the corticospinal tract without causing the subject discomfort. Since TMS was introduced, numerous applications of the technique have been developed for the evaluation of neurologic diseases. Standard TMS applications (central motor conduction time, threshold and amplitude of motor evoked potentials) allow the evaluation of motor conduction in the CNS. Conduction studies provide specific information in neurologic conditions characterized by clinical and subclinical upper motor neuron involvement. In addition, they have proved useful in monitoring motor abnormalities and the recovery of motor function. TMS also gives information on the pathophysiology of the processes underlying the various clinical conditions. More complex TMS applications (paired-pulse stimulation, silent period, ipsilateral silent period, input-output curve, and evaluation of central fatigue) allow investigation into the mechanisms of diseases causing changes in the excitability of cortical motor areas. These techniques are also useful in monitoring the effects of neurotrophic drugs on cortical activity. TMS applications have an important place among the investigative tools to study patients with motor disorders.

Organizing Patient Involvement

DEFF Research Database (Denmark)

Brehm Johansen, Mette

hospitals. During the last 25 years, patient involvement and quality improvement have become connected in Danish healthcare policy. However, the ideal of involving patients in quality improvement is described in very general terms and with only few specific expectations of how it is to be carried out...... in practice, as I show in the thesis. In the patient involvement literature, the difficulties of getting patient involvement in quality improvement to have in an impact on the planning and development of healthcare services is, for example, ascribed to conceptual vagueness of patient involvement, differences...... in perspectives, values and understandings between patients and healthcare professionals, or the lack of managerial attention and prioritization....

Early tumour detection: a transillumination, time-resolved technique

International Nuclear Information System (INIS)

Behin-Ain, S.; Van Doorn, T.; Patterson, J.

2000-01-01

Full text: Research into transillumination techniques for the detection of tumours in soft tissue has been ongoing for over 70 years. The resolution and contrast, however, remain severely limited by scatter. Single photon detection techniques, with ideally infinite extinction coefficients, have been proposed to accumulate sub-hertz photon transmitted frequencies in the early part of a transmitted pulse. Computer based simulations have been undertaken to examine the theoretical performance requirements of the detector and the resultant image qualities that may be expected with this imaging technique. This paper reports on the computational techniques required for implementing these simulations in an efficient manner. Controlled Monte Carlo (CMC) and Convolution of Layers (CL) techniques were employed to constrain the photon to those having more chance of detection and hence enhance the detection statistics. Extrapolation techniques are proposed to reconstruct the early part of the temporal profile. Computational methods were implemented to evaluate Path Integrals, which are otherwise overly complex to evaluate. CMC and CL reduce the computational time by more than 10 orders of magnitude by only tracking those photons more likely to reach the detector. In the case of an optically thick medium with high scattering coefficient, extrapolation techniques are used to reconstruct the early part of temporal profile. Analytical solutions were found to be too involved for the simplest geometries. However the CL and implementation of computational techniques make Path integrals a useful analytical tool to compliment full Monte Carlo techniques. Results have shown that these methods collectively enable detection of small inhomogeneites within soft tissues. Reduced computation times and full reconstruction of the temporal profile of transmitted photons through optically thick medium enable fast simulations of single photon detectors to be achieved with the above described

Studies involving direct heating of uranium and plutonium oxides by microwaves

Energy Technology Data Exchange (ETDEWEB)

Mallik, G K; Malav, R K; Karande, A P; Bhargava, V K; Kamath, H S [Bhabha Atomic Research Centre, Tarapur (India). Advanced Fuel Fabrication Facility

1997-08-01

Nuclear fuel fabrication and recovery of nuclear materials from scraps generated during fabrication involve heating steps like dewaxing, sintering, roasting of scraps, calcination, etc. The dielectric properties of uranium and plutonium oxides place them in the category of materials which are susceptible to absorption of microwaves. The studies were carried out to explore the microwave heating technique for these steps required in nuclear fuel fabrication and scrap recovery laboratories. (author). 1 ref.

Involvement of Machine Learning for Breast Cancer Image Classification: A Survey

OpenAIRE

Nahid, Abdullah-Al; Kong, Yinan

2017-01-01

Breast cancer is one of the largest causes of women’s death in the world today. Advance engineering of natural image classification techniques and Artificial Intelligence methods has largely been used for the breast-image classification task. The involvement of digital image classification allows the doctor and the physicians a second opinion, and it saves the doctors’ and physicians’ time. Despite the various publications on breast image classification, very few review papers are available w...

Simplification of Bovine Somatic Cell Nuclear Transfer by Application of a Zona-Free Manipulation Technique

DEFF Research Database (Denmark)

Booth, Paul J; Tan, Shijian; Reipurth, Rikke

2001-01-01

Contemporary nuclear transfer techniques often require the involvement of skilled personnel and extended periods of micromanipulation. Here, we present details of the development of a nuclear transfer technique for somatic cells that is both simpler and faster than traditional methods. The techni......Contemporary nuclear transfer techniques often require the involvement of skilled personnel and extended periods of micromanipulation. Here, we present details of the development of a nuclear transfer technique for somatic cells that is both simpler and faster than traditional methods....... The technique comprises the bisection of zona-free oocytes and the reconstruction of embryos comprising two half cytoplasts and a somatic cell by adherence using phytohaemagglutinin-P (PHA) followed by an electropulse and subsequent culture in microwells (termed WOWs--well of the well). The development......-intact zygotes were not different in either blastocyst yield (44.6 +/- 2.4% versus 51.8 +/- 13.5% [mean +/- SEM]) or quality (126.3 +/- 48.4 versus 119.9 +/- 32.6 total cells), and exposure of zygotes to PHA-P did not reduce blastocyst yields compared to vehicle control (40.8 +/- 11.6% versus 47.1 +/- 20...

Ultrasonic testing of austenitic welds and its dependency on the welding process

International Nuclear Information System (INIS)

Tabatabaeipour, S.M.; Honarvar, F.

2009-01-01

This paper describes the ultrasonic testing of austenitic welds prepared by two different welding processes. The tests were carried out by the ultrasonic Time-of-Flight Diffraction (ToFD) technique. Shielded Metal Arc Welding (SMAW) and Gas Tungsten Arc Welding (GTAW) are the welding processes used for preparing the specimens. Identical artificial defects were implanted in both welds during the welding process. Both specimens were examined by the ToFD technique under similar conditions. Metallographic images were also obtained from the cross sectional plane of both the SMA and GTA welds. These images show that the grain orientation in the two welded specimens are different. D-scan images obtained by the ToFD technique from these welds indicates that inspecting the specimens prepared by the SMAW process is easier than the one made by the GTAW process. The results also show that the D-scan images cannot reveal the small vertical drilled holes implanted in the specimens. (author)

The irradiation behaviour of boron carbide/graphite between 800 and 1,1000C

International Nuclear Information System (INIS)

Hattenbach, K.; Hilgendorff, W.; Weiler, K.; Zimmermann, H.U.

1975-01-01

64 samples of boron carbide/graphite, a material used as burnable poison in high temperature reactors, were irradiated at temperatures between 800 and 1,100 0 C up to a fluence of 1-2 x 10 20 nvt. The following post-investigations were extended to dimensional measurements to determime a possible swelling or shrinking of the pellet, corrosion tests in completely desalinated water at 300 0 C, preparation of metallographic microsections to check for crack formation, determination of the helium hold back power and the thus involved gas chromatic analysis, as well as burn-up determinations by determining the boron 10/boron 11 ratio and the lithium concentration. (orig./LN) [de

Fusion excitation functions involving transitional nuclei

Energy Technology Data Exchange (ETDEWEB)

Rehm, K.E.; Jiang, C.L.; Esbensen, H. [and others

1995-08-01

Measurements of fusion excitation functions involving transitional nuclei {sup 78}Kr and {sup 100}Mo showed a different behavior at low energies, if compared to measurements with {sup 86}Kr and {sup 92}Mo. This points to a possible influence of nuclear structure on the fusion process. One way to characterize the structure of vibrational nuclei is via their restoring force parameters C{sub 2} which can be calculated from the energy of the lowest 2{sup +} state and the corresponding B(E2) value. A survey of the even-even nuclei between A = 28-150 shows strong variations in C{sub 2} values spanning two orders of magnitude. The lowest values for C{sub 2} are observed for {sup 78}Kr, {sup 104}Ru and {sup 124}Xe followed by {sup 74,76}Ge, {sup 74,76}Se, {sup 100}Mo and {sup 110}Pd. In order to learn more about the influence of {open_quotes}softness{close_quotes} on the sub-barrier fusion enhancement, we measured cross sections for evaporation residue production for the systems {sup 78}Kr + {sup 104}Ru and {sup 78}Kr + {sup 76}Ge with the gas-filled magnet technique. For both systems, fusion excitation functions involving the closed neutron shell nucleus {sup 86}Kr were measured previously. The data are presently being analyzed.

Photogrammetry: applications of a three-dimensional remote measurement technique

International Nuclear Information System (INIS)

Peak, K.

1988-01-01

Photogrammetry is defined as the precise art of abstracting measurements from photographic images. Used for many years as a means to produce the world's maps, it has, in recent years, been applied in many engineering environments. The nuclear industry has, in particular, benefitted from the close range applications of photogrammetry. This paper sets out to describe the techniques involved, from the site photography through to the analytical data extraction. It will include a number of examples of where photogrammetry has been used in the nuclear industry as a remote measurement technique, from simple monitoring exercises to the compilation of complex three-dimensional as-built computer models. (author)

Edge compression techniques for visualization of dense directed graphs.

Science.gov (United States)

Dwyer, Tim; Henry Riche, Nathalie; Marriott, Kim; Mears, Christopher

2013-12-01

We explore the effectiveness of visualizing dense directed graphs by replacing individual edges with edges connected to 'modules'-or groups of nodes-such that the new edges imply aggregate connectivity. We only consider techniques that offer a lossless compression: that is, where the entire graph can still be read from the compressed version. The techniques considered are: a simple grouping of nodes with identical neighbor sets; Modular Decomposition which permits internal structure in modules and allows them to be nested; and Power Graph Analysis which further allows edges to cross module boundaries. These techniques all have the same goal--to compress the set of edges that need to be rendered to fully convey connectivity--but each successive relaxation of the module definition permits fewer edges to be drawn in the rendered graph. Each successive technique also, we hypothesize, requires a higher degree of mental effort to interpret. We test this hypothetical trade-off with two studies involving human participants. For Power Graph Analysis we propose a novel optimal technique based on constraint programming. This enables us to explore the parameter space for the technique more precisely than could be achieved with a heuristic. Although applicable to many domains, we are motivated by--and discuss in particular--the application to software dependency analysis.

Effect of Scratches on Pinch Welds

International Nuclear Information System (INIS)

Korinko, P

2005-01-01

Fill stems for tritium reservoirs have stringent scratch requirements such that any indications that appear to have depth are cause for rework or rejection. A scoping study was undertaken to evaluate the effect of scratches approximately 0.0015 to 0.002 inch deep on the fitness for service and bond quality. The stems were characterized using borescope before and after welding. The four stems were welded with near optimal weld parameters, proof tested, and examined metallographically. The stems were radiographed, proof tested, and examined metallographically. The scratches did not adversely affect (1) the weld integrity based on radiography, (2) the ability to withstand the proof pressure, and (3) the weld quality based on metallographic cross-sections. Based on these limited results at a nominal weld current, the weld process is very robust. It may be able to recover from manufacturing defects and inspection anomalies worse than those expected for typical fill stem manufacturing processes; additional testing specific to each application over a range of weld heats is needed to verify applicability of these results

Applied ALARA techniques

International Nuclear Information System (INIS)

Waggoner, L.O.

1998-01-01

The presentation focuses on some of the time-proven and new technologies being used to accomplish radiological work. These techniques can be applied at nuclear facilities to reduce radiation doses and protect the environment. The last reactor plants and processing facilities were shutdown and Hanford was given a new mission to put the facilities in a safe condition, decontaminate, and prepare them for decommissioning. The skills that were necessary to operate these facilities were different than the skills needed today to clean up Hanford. Workers were not familiar with many of the tools, equipment, and materials needed to accomplish:the new mission, which includes clean up of contaminated areas in and around all the facilities, recovery of reactor fuel from spent fuel pools, and the removal of millions of gallons of highly radioactive waste from 177 underground tanks. In addition, this work has to be done with a reduced number of workers and a smaller budget. At Hanford, facilities contain a myriad of radioactive isotopes that are 2048 located inside plant systems, underground tanks, and the soil. As cleanup work at Hanford began, it became obvious early that in order to get workers to apply ALARA and use hew tools and equipment to accomplish the radiological work it was necessary to plan the work in advance and get radiological control and/or ALARA committee personnel involved early in the planning process. Emphasis was placed on applying,ALARA techniques to reduce dose, limit contamination spread and minimize the amount of radioactive waste generated. Progress on the cleanup has,b6en steady and Hanford workers have learned to use different types of engineered controls and ALARA techniques to perform radiological work. The purpose of this presentation is to share the lessons learned on how Hanford is accomplishing radiological work

Applied ALARA techniques

Energy Technology Data Exchange (ETDEWEB)

Waggoner, L.O.

1998-02-05

The presentation focuses on some of the time-proven and new technologies being used to accomplish radiological work. These techniques can be applied at nuclear facilities to reduce radiation doses and protect the environment. The last reactor plants and processing facilities were shutdown and Hanford was given a new mission to put the facilities in a safe condition, decontaminate, and prepare them for decommissioning. The skills that were necessary to operate these facilities were different than the skills needed today to clean up Hanford. Workers were not familiar with many of the tools, equipment, and materials needed to accomplish:the new mission, which includes clean up of contaminated areas in and around all the facilities, recovery of reactor fuel from spent fuel pools, and the removal of millions of gallons of highly radioactive waste from 177 underground tanks. In addition, this work has to be done with a reduced number of workers and a smaller budget. At Hanford, facilities contain a myriad of radioactive isotopes that are 2048 located inside plant systems, underground tanks, and the soil. As cleanup work at Hanford began, it became obvious early that in order to get workers to apply ALARA and use hew tools and equipment to accomplish the radiological work it was necessary to plan the work in advance and get radiological control and/or ALARA committee personnel involved early in the planning process. Emphasis was placed on applying,ALARA techniques to reduce dose, limit contamination spread and minimize the amount of radioactive waste generated. Progress on the cleanup has,b6en steady and Hanford workers have learned to use different types of engineered controls and ALARA techniques to perform radiological work. The purpose of this presentation is to share the lessons learned on how Hanford is accomplishing radiological work.

Governing integration through sports. A case study of civil society involvement in welfare policy

DEFF Research Database (Denmark)

Agergaard, Sine; Michelsen la Cour, Annette

2012-01-01

governing techniques of the welfare state. To do so, a case study approach is applied. First of all, the article will describe the ways in which the issues of enhancing ethnic integration through sports is represented (thought of as a problem) by the involved public authorities and non-state actors using...

New Product Development in an Emerging Economy: Analysing the Role of Supplier Involvement Practices by Using Bayesian Markov Chain Monte Carlo Technique

Directory of Open Access Journals (Sweden)

Kanagi Kanapathy

2014-01-01

Full Text Available The research question is whether the positive relationship found between supplier involvement practices and new product development performances in developed economies also holds in emerging economies. The role of supplier involvement practices in new product development performance is yet to be substantially investigated in the emerging economies (other than China. This premise was examined by distributing a survey instrument (Jayaram’s (2008 published survey instrument that has been utilised in developed economies to Malaysian manufacturing companies. To gauge the relationship between the supplier involvement practices and new product development (NPD project performance of 146 companies, structural equation modelling was adopted. Our findings prove that supplier involvement practices have a significant positive impact on NPD project performance in an emerging economy with respect to quality objectives, design objectives, cost objectives, and “time-to-market” objectives. Further analysis using the Bayesian Markov Chain Monte Carlo algorithm, yielding a more credible and feasible differentiation, confirmed these results (even in the case of an emerging economy and indicated that these practices have a 28% impact on variance of NPD project performance. This considerable effect implies that supplier involvement is a must have, although further research is needed to identify the contingencies for its practices.

Compensation Techniques in Accelerator Physics

Energy Technology Data Exchange (ETDEWEB)

Sayed, Hisham Kamal [Old Dominion Univ., Norfolk, VA (United States)

2011-05-01

Accelerator physics is one of the most diverse multidisciplinary fields of physics, wherein the dynamics of particle beams is studied. It takes more than the understanding of basic electromagnetic interactions to be able to predict the beam dynamics, and to be able to develop new techniques to produce, maintain, and deliver high quality beams for different applications. In this work, some basic theory regarding particle beam dynamics in accelerators will be presented. This basic theory, along with applying state of the art techniques in beam dynamics will be used in this dissertation to study and solve accelerator physics problems. Two problems involving compensation are studied in the context of the MEIC (Medium Energy Electron Ion Collider) project at Jefferson Laboratory. Several chromaticity (the energy dependence of the particle tune) compensation methods are evaluated numerically and deployed in a figure eight ring designed for the electrons in the collider. Furthermore, transverse coupling optics have been developed to compensate the coupling introduced by the spin rotators in the MEIC electron ring design.

Reliability of system identification techniques to assess standing balance in healthy elderly

NARCIS (Netherlands)

Pasma, Jantsje H.; Engelhart, Denise; Maier, Andrea B.; Aarts, Ronald G.K.M.; Van Gerven, Joop M.A.; Arendzen, J. Hans; Schouten, Alfred C.; Meskers, Carel G.M.; Van Kooij, Herman Der

2016-01-01

Objectives System identification techniques have the potential to assess the contribution of the underlying systems involved in standing balance by applying well-known disturbances. We investigated the reliability of standing balance parameters obtained with multivariate closed loop system

Reliability of System Identification Techniques to Assess Standing Balance in Healthy Elderly

NARCIS (Netherlands)

Pasma, J.H.; Engelhart, D.; Maier, A.B.; Aarts, R.G.K.M.; Van Gerven, J.M.A.; Arendzen, J.H.; Schouten, A.C.; Meskers, C.G.M.; Van der Kooij, H.

2016-01-01

Objectives System identification techniques have the potential to assess the contribution of the underlying systems involved in standing balance by applying well-known disturbances. We investigated the reliability of standing balance parameters obtained with multivariate closed loop system

Microstructure and mechanical properties of precipitation hardened aluminum under high rate deformation

International Nuclear Information System (INIS)

Grady, D.E.; Asav, J.R.; Rohde, R.W.; Wise, J.L.

1983-01-01

This chapter attempts to correlate the shock compression and quasistatic deformation of 6061-T6 aluminium. Examines recovered specimens which have been shock loaded, and compares results with both static and dynamic mechanical property measurements. Discusses experimental procedures (reshock and unloading experiments, shock recovery techniques, metallographic techniques and coldwork experiments); dynamic strength and wave-profile properties (strength and shear-stress states on the Hugoniot, steady-wave risetime and viscosity); quasistatic and shock metallography studies (metallography of quasistatically deformed material; metallography of shock deformed specimens; comparison of static and shock deformation; correlation of hardness and dynamic strength measurements); and thermal trapping calculations in shocked aluminium (heterogeneous deformation and adiabatic heating in shock-wave loading; energy and risetime relations under steadywave shock compression; heterogeneous temperature calculations in aluminium). Concludes that heterogeneous shear deformation appears to play a role in the dynamic deformation process

Blower-door techniques for measuring interzonal leakage

Energy Technology Data Exchange (ETDEWEB)

Hult, Erin L.; Sherman, Max H.; Walker, Iain

2013-01-01

Abstract The standard blower door test methods, such as ASTM E779, describe how to use a single blower door to determine the total leakage of a single-zone structure such as a detached single-family home. There are no standard test methods for measuring interzonal leakage in a two-zone or multi-zone building envelope such as might be encountered in with an attached garage or in a multifamily building. Some practitioners have been using techniques that involve making multiple measurements with a single blower door as well as combined measurements using multiple blower doors. Even for just two zones there are dozens of combinations of one-door and two-door test protocols that could conceivably be used to determine the interzonal air tightness. We examined many of these two-zone configurations using both simulation and measured data to estimate the accuracy and precision of each technique for realistic measurement scenarios. We also considered the impact of taking measurements at a single pressure versus over multiple pressures. We compared the various techniques and evaluated them for specific uses. Some techniques work better in one leakage regime; some are more sensitive to wind and other noise; some are more suited to determining only a subset of the leakage values. This paper makes recommendations on which techniques to use or not use for various cases and provides data that could be used to develop future test methods.

Involving disabled children and young people as partners in research: a systematic review.

Science.gov (United States)

Bailey, S; Boddy, K; Briscoe, S; Morris, C

2015-07-01

Children and young people can be valuable partners in research, giving their unique perspectives on what and how research should be done. However, disabled children are less commonly involved in research than their non-disabled peers. This review investigated how disabled children have been involved as research partners; specifically how they have been recruited, the practicalities and challenges of involvement and how these have been overcome, and impacts of involvement for research, and disabled children and young people. The INVOLVE definition of involvement and the Equality and Human Rights Commission definition of disability were used. Relevant bibliographic databases were searched. Websites were searched for grey literature. Included studies had involved disabled children and young people aged 5-25 years in any study design. Reviews, guidelines, reports and other documents from the grey literature were eligible for inclusion. Twenty-two papers were included: seven reviews, eight original research papers, three reports, three guidelines and one webpage. Nine examples of involvement were identified. Recommendations included developing effective communication techniques, using flexible methods that can be adapted to needs and preferences, and ensuring that sufficient support and funding is available for researchers undertaking involvement. Positive impacts of involvement for disabled children included increased confidence, self-esteem and independence. Positive impacts for research were identified. Involving disabled children in research can present challenges; many of these can be overcome with sufficient time, planning and resources. More needs to be done to find ways to involve those with non-verbal communication. Generally, few details were reported about disabled children and young people's involvement in studies, and the quality of evidence was low. Although a range of positive impacts were identified, the majority of these were authors' opinions rather

Conference on Techniques of Nuclear and Conventional Analysis and Applications

International Nuclear Information System (INIS)

2012-01-01

Full text : With their wide scope, particularly in the areas of environment, geology, mining, industry and life sciences; analysis techniques are of great importance in research as fundamental and applied. The Conference on Techniques for Nuclear and Conventional Analysis and Applications (TANCA) are Registered in the national strategy of opening of the University and national research centers on their local, national and international levels. This conference aims to: Promoting nuclear and conventional analytical techniques; Contribute to the creation of synergy between the different players involved in these techniques include, Universities, Research Organizations, Regulatory Authorities, Economic Operators, NGOs and others; Inform and educate potential users of the performance of these techniques; Strengthen exchanges and links between researchers, industry and policy makers; Implement a program of inter-laboratory comparison between Moroccan one hand, and their foreign counterparts on the other; Contribute to the research training of doctoral students and postdoctoral scholars. Given the relevance and importance of the issues related to environment and impact on cultural heritage, this fourth edition of TANCA is devoted to the application of analytical techniques for conventional and nuclear Questions ied to environment and its impact on cultural heritage.

Demonstration and evaluation of recent air-sealing techniques in housing

Energy Technology Data Exchange (ETDEWEB)

Mayhew, W.J.

1987-09-01

The Airtight Drywall Approach (ADA) and the sealed polyethylene approach were developed as two distinct systems for reducing air leakage in housing. Builders have not totally accepted either method but have instead tended to borrow the most practical and cost-effective techniques and materials from each system and combined them into hybrid systems. This project evaluated current air-sealing techniques, developed refinements to some of those techniques and incorporated them into the construction of the Cold Climate Demonstration House (CCDH), a research and demonstration facility in Alberta. By comparing the effectiveness and practical use of different air and vapour retarder materials and techniques, it was found that for the air barrier, ADA materials and techniques were more easily installed. The resulting air seal was more reliable. However, until inspectors accept alkyd or vapor barrier paints as the vapor retarder, polyethylene is recommended. The construction techniques recommended in this report can be installed with a minimum of experience and with minimal involvement of other subtrades. The cost to provide an air/vapor barrier for a 1000 ft /sup 2/ bilevel with both levels fully developed (as demonstrated in the CCDH) was approximately $360. 26 figs.

Five years' experience of the modified Meek technique in the management of extensive burns.

Science.gov (United States)

Hsieh, Chun-Sheng; Schuong, Jen-Yu; Huang, W S; Huang, Ted T

2008-05-01

The Meek technique of skin expansion is useful for covering a large open wound with a small piece of skin graft, but requires a carefully followed protocol. Over the past 5 years, a skin graft expansion technique following the Meek principle was used to treat 37 individuals who had sustained third degree burns involving more than 40% of the body surface. A scheme was devised whereby the body was divided into six areas, in order to clarify the optimal order of wound debridements and skin grafting procedures as well as the regimen of aftercare. The mean body surface involvement was 72.9% and the mean area of third degree burns was 41%. The average number of operations required was 1.84. There were four deaths among in this group of patients. The Meek technique of skin expansion and the suggested protocol are together efficient and effective in covering an open wound, particularly where there is a paucity of skin graft donor sites.

Journaling; an active learning technique.

Science.gov (United States)

Blake, Tim K

2005-01-01

Journaling is a method frequently discussed in nursing literature and educational literature as an active learning technique that is meant to enhance reflective practice. Reflective practice is a means of self-examination that involves looking back over what has happened in practice in an effort to improve, or encourage professional growth. Some of the benefits of reflective practice include discovering meaning, making connections between experiences and the classroom, instilling values of the profession, gaining the perspective of others, reflection on professional roles, and development of critical thinking. A review of theory and research is discussed, as well as suggestions for implementation of journaling into coursework.

Influence of Involvement in Sports on Students' Involvement in ...

African Journals Online (AJOL)

This study was carried out to establish whether students' involvement in sports activities affected their involvement in academic activities. Data were collected using a self-administered questionnaire and analysed using percentages and means. Spearman's correlation coefficient was used to test the hypotheses that guided ...

Feeding Techniques for Children Who Have Cleft Lip and Palate.

Science.gov (United States)

Klein, Marsha Dunn

This pamphlet on feeding techniques for children who have cleft lip and palate emphasizes the role of the parent as part of a team involving many specialists. The pamphlet begins with explanations of complete and incomplete separations of the lip, unilateral and bilateral cleft lips, corrective surgical procedures, etc. The importance of weight…

Pattern of parental acceptance of management techniques used in pediatric dentistry.

Science.gov (United States)

Peretz, Benjamin; Kharouba, Johnny; Blumer, Sigalit

2013-01-01

To evaluate parents' acceptance of management techniques in Israeli pediatric dental clinics. Ninety parents who accompanied their children to three pediatric dental clinics provided information on selected parameters including their attitudes about management techniques. 68.9% of the parents preferred to stay in the treatment room. The most accepted technique was positive reinforcement (81.1%) followed by tell-show-do (TSD) (76.7%, with younger parents more accepting than older, p = 0.049). The least accepted techniques were restraint (1.1%) and voice control (7.8%, especially by parents with the highest dental anxiety, p = 0.002). Sedation was unacceptable by 15.6% of the parents: those with the lowest dental anxiety agreed to sedation significantly more than those with greater dental anxiety (p = 0.031). Parents preferred more positive approaches and management techniques that involve demonstrations geared for the child's level of understanding. Restraint and voice control were more strongly rejected than sedation.

Techniques to maximize software reliability in radiation fields

International Nuclear Information System (INIS)

Eichhorn, G.; Piercey, R.B.

1986-01-01

Microprocessor system failures due to memory corruption by single event upsets (SEUs) and/or latch-up in RAM or ROM memory are common in environments where there is high radiation flux. Traditional methods to harden microcomputer systems against SEUs and memory latch-up have usually involved expensive large scale hardware redundancy. Such systems offer higher reliability, but they tend to be more complex and non-standard. At the Space Astronomy Laboratory the authors have developed general programming techniques for producing software which is resistant to such memory failures. These techniques, which may be applied to standard off-the-shelf hardware, as well as custom designs, include an implementation of Maximally Redundant Software (MRS) model, error detection algorithms and memory verification and management

Oscillations in deviating difference equations using an iterative technique

Directory of Open Access Journals (Sweden)

George E Chatzarakis

2017-07-01

Full Text Available Abstract The paper deals with the oscillation of the first-order linear difference equation with deviating argument and nonnegative coefficients. New sufficient oscillation conditions, involving limsup, are given, which essentially improve all known results, based on an iterative technique. We illustrate the results and the improvement over other known oscillation criteria by examples, numerically solved in Matlab.

Capturing Parents' Individual and Institutional Interest Toward Involvement in Science Education

Science.gov (United States)

Kaya, Sibel; Lundeen, Cynthia

2010-11-01

Parents are generally less involved in their children’s science education (as compared to reading and mathematics) due to low self-efficacy and a lack of home-school communication. This study examined parental interest and attitudes in science as well as the nature of parent-to-child questioning during an interactive home, school, and community collaboration in the southeastern United States. Study results, compiled from observations, exit surveys, and interviews revealed largely positive family interactions and attitudes about science learning and increased parental interest toward involvement in elementary science. Parents frequently used productive questioning techniques during activities. These results imply that successful home, school, and community partnerships may elevate levels of parental participation in their children’s science education and the parents’ perception of themselves as being competent in assisting in science.

Can women's autonomy impede male involvement in pregnancy health in Katmandu, Nepal?

Science.gov (United States)

Mullany, Britta C; Hindin, Michelle J; Becker, Stan

2005-11-01

Women's empowerment programs focus primarily on increasing the decision-making power of women, while male involvement/couple-friendly programs emphasize communication and negotiation within couples in making decisions. In-depth-interviews and focus group discussions were conducted to investigate patterns of household decision-making and the context of male involvement behaviors in Katmandu, Nepal. A questionnaire focusing on household decision-making and husbands' roles during pregnancy was administered to 592 pregnant women receiving antenatal services at a large maternity hospital. Multivariate regression techniques were used to compare male involvement behaviors across varying levels of women's autonomy, represented by different decision-making patterns. Higher women's autonomy, as measured by her sole final decision-making power, was associated with significantly lower male involvement in pregnancy health. After adjustment for other covariates, each additional decision in which a woman had final say was associated with a significantly lower likelihood of her husband accompanying her to antenatal care (OR=0.70, pempowerment and/or women's health must consider the dynamics and ramifications of including or excluding males in their efforts. Involving husbands and encouraging couples' joint decision-making in reproductive and family health may provide an important strategy in achieving both women's empowerment and women's health goals.

An easy irradiation technique (partial half-beam) to reduce renal dose in radiotherapy of cervical cancer including paraaortic lymph nodes

International Nuclear Information System (INIS)

Vorwerk, H.; Wagner, D.; Christiansen, H.; Hess, C.F.; Hermann, R.M.

2008-01-01

Purpose: for radiation treatment of patients with cervical cancer and a high risk for paraaortic lymph node involvement, an easy three-dimensional (3-D) conformal irradiation technique (partial half-beam [PHB]) for protection of organs at risk, especially of renal tissue, was developed. Patients and methods: in five consecutive female patients a computed tomography scan was performed. Dose-volume histograms of the renal tissue and other organs at risk were analyzed for PHB, three other 3-D conformal techniques, and an intensity-modulated radiotherapy (IMRT) technique. Results: the PHB technique reduced the renal volume and volumes of other organs at risk exposed to radiation doses when comparing all patients to the other 3-D conformal techniques. With use of the IMRT technique more renal tissue volume received very low radiation doses (≤ 6.8 Gy) whereas the D 10 was lower than with the PHB technique. Conclusion: in female patients with cervical cancer and high risk for paraaortic lymph node involvement, the use of the PHB technique is recommended to reduce renal radiation exposure, if no IMRT technique should be applied. The PHB technique is very easily and fast applicable. (orig.)

Inhaler technique maintenance: gaining an understanding from the patient's perspective.

Science.gov (United States)

Ovchinikova, Ludmila; Smith, Lorraine; Bosnic-Anticevich, Sinthia

2011-08-01

The aim of this study was to determine the patient-, education-, and device-related factors that predict inhaler technique maintenance. Thirty-one community pharmacists were trained to deliver inhaler technique education to people with asthma. Pharmacists evaluated (based on published checklists), and where appropriate, delivered inhaler technique education to patients (participants) in the community pharmacy at baseline (Visit 1) and 1 month later (Visit 2). Data were collected on participant demographics, asthma history, current asthma control, history of inhaler technique education, and a range of psychosocial aspects of disease management (including adherence to medication, motivation for correct technique, beliefs regarding the importance of maintaining correct technique, and necessity and concern beliefs regarding preventer therapy). Stepwise backward logistic regression was used to identify the predictors of inhaler technique maintenance at 1 month. In total 145 and 127 participants completed Visits 1 and 2, respectively. At baseline, 17% of patients (n = 24) demonstrated correct technique (score 11/11) which increased to 100% (n = 139) after remedial education by pharmacists. At follow-up, 61% (n = 77) of patients demonstrated correct technique. The predictors of inhaler technique maintenance based on the logistic regression model (X(2) (3, N = 125) = 16.22, p = .001) were use of a dry powder inhaler over a pressurized metered-dose inhaler (OR 2.6), having better asthma control at baseline (OR 2.3), and being more motivated to practice correct inhaler technique (OR 1.2). Contrary to what is typically recommended in previous research, correct inhaler technique maintenance may involve more than repetition of instructions. This study found that past technique education factors had no bearing on technique maintenance, whereas patient psychosocial factors (motivation) did.

Solution chemistry techniques in SYNROC preparation

International Nuclear Information System (INIS)

Dosch, R.G.; Lynch, A.W.

1981-07-01

Investigations of titanate-based ceramic forms for radioactive waste immobilization are underway at Sandia National Laboratories (SNLA) and at Lawrence Livermore National Laboratory (LLNL). Although the waste forms differ as to overall product composition, the waste-containing phases in both ceramic products have similar crystalline structure types. These include metallic phases along with oxides with structure types of the mineral analogues perovskite, zirconolite, and hollandite. Significant differences also exist in the area of processing. More conventional ceramic processing methods are used at LLNL to produce SYNROC while solution chemistry techniques involving metal alkoxide chemistry and ion exchange have been developed at SNLA to prepare calcium titanate-based waste ceramics. The SNLA techniques were recently modified and applied to producing SYNROC (compositions C and D) as part of an interlaboratory information exchange between SNLA and LLNL. This report describes the methods used in preparing SYNROC including the solution interaction, and hot-pressing methods used to obtain fully dense SYNROC monoliths

Cogeneration techniques; Les techniques de cogeneration

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

This dossier about cogeneration techniques comprises 12 parts dealing successively with: the advantages of cogeneration (examples of installations, electrical and thermal efficiency); the combustion turbine (principle, performances, types); the alternative internal combustion engines (principle, types, rotation speed, comparative performances); the different configurations of cogeneration installations based on alternative engines and based on steam turbines (coal, heavy fuel and natural gas-fueled turbines); the environmental constraints of combustion turbines (pollutants, techniques of reduction of pollutant emissions); the environmental constraints of alternative internal combustion engines (gas and diesel engines); cogeneration and energy saving; the techniques of reduction of pollutant emissions (pollutants, unburnt hydrocarbons, primary and secondary (catalytic) techniques, post-combustion); the most-advanced configurations of cogeneration installations for enhanced performances (counter-pressure turbines, massive steam injection cycles, turbo-chargers); comparison between the performances of the different cogeneration techniques; the tri-generation technique (compression and absorption cycles). (J.S.)

Microtunneling techniques to form an insitu barrier around existing structures

International Nuclear Information System (INIS)

Coller, P.J.; Abbott, D.G.

1994-01-01

The use of microtunneling techniques to construct underground structures has been available for many years. The technique, typically termed pipe roofing, is well proven and, to date, has been used principally to form underground access under existing structures where the use of cut and cover or conventional tunneling techniques was either impossible or too expensive. The first project involving the use of Iseki equipment, the first use of the pipe roofing technique as far as we are aware, was in 1971. This was followed by a number of projects in Japan, together with projects in Singapore and Hong Kong, totaling 12 projects. More recently, projects have been completed in Singapore and Japan and are currently in progress in Japan and Malaysia. This paper will briefly describe the use of the technique and the use of the new Iseki Unclemole for hard rock excavation to construct the largest pipe roof project ever undertaken in the world, together with other projects. The pipe roofing technique allows the construction of underground structures, in a variety of shapes and forms, by the use of remotely operated microtunnel machines. The paper will describe the potential application of this technique in the areas of hazardous and nuclear waste management

Silver surface enrichment of silver-copper alloys: a limitation for the analysis of ancient silver coins by surface techniques

International Nuclear Information System (INIS)

Beck, L.; Bosonnet, S.; Reveillon, S.; Eliot, D.; Pilon, F.

2004-01-01

The surface enrichment of archaeological silver-copper alloys has been recognized for many years. However, the origin of this enrichment is not well defined and many hypotheses have been put forward to account for this behaviour: segregation of the components during casting, deliberate thermal and/or chemical post-treatment, abrasion or corrosion. Among the hypotheses mentioned above, we have focused our study on the first step of coin manufacturing. Replications of silver-copper standards of various compositions ranging from 30% to 80% Ag, reflecting the composition of silver blanks, have been produced. Metallographic examination, PIXE and SEM-EDS have been used for the characterization of each sample. A model of the direct enrichment has been established. This model allows us to propose a relationship between the surface composition and the silver content of the core. Comparison with data of Roman coins from the Roman site of Cha-hat teaubleau (France) and from the literature and consequences for the analyses of ancient coins by surface methods are presented

Analytical research using synchrotron radiation based techniques

International Nuclear Information System (INIS)

Jha, Shambhu Nath

2015-01-01

There are many Synchrotron Radiation (SR) based techniques such as X-ray Absorption Spectroscopy (XAS), X-ray Fluorescence Analysis (XRF), SR-Fourier-transform Infrared (SRFTIR), Hard X-ray Photoelectron Spectroscopy (HAXPS) etc. which are increasingly being employed worldwide in analytical research. With advent of modern synchrotron sources these analytical techniques have been further revitalized and paved ways for new techniques such as microprobe XRF and XAS, FTIR microscopy, Hard X-ray Photoelectron Spectroscopy (HAXPS) etc. The talk will cover mainly two techniques illustrating its capability in analytical research namely XRF and XAS. XRF spectroscopy: XRF spectroscopy is an analytical technique which involves the detection of emitted characteristic X-rays following excitation of the elements within the sample. While electron, particle (protons or alpha particles), or X-ray beams can be employed as the exciting source for this analysis, the use of X-ray beams from a synchrotron source has been instrumental in the advancement of the technique in the area of microprobe XRF imaging and trace level compositional characterisation of any sample. Synchrotron radiation induced X-ray emission spectroscopy, has become competitive with the earlier microprobe and nanoprobe techniques following the advancements in manipulating and detecting these X-rays. There are two important features that contribute to the superb elemental sensitivities of microprobe SR induced XRF: (i) the absence of the continuum (Bremsstrahlung) background radiation that is a feature of spectra obtained from charged particle beams, and (ii) the increased X-ray flux on the sample associated with the use of tunable third generation synchrotron facilities. Detection sensitivities have been reported in the ppb range, with values of 10 -17 g - 10 -14 g (depending on the particular element and matrix). Keeping in mind its demand, a microprobe XRF beamline has been setup by RRCAT at Indus-2 synchrotron

Application of geometric algebra to electromagnetic scattering the Clifford-Cauchy-Dirac technique

CERN Document Server

Seagar, Andrew

2016-01-01

This work presents the Clifford-Cauchy-Dirac (CCD) technique for solving problems involving the scattering of electromagnetic radiation from materials of all kinds. It allows anyone who is interested to master techniques that lead to simpler and more efficient solutions to problems of electromagnetic scattering than are currently in use. The technique is formulated in terms of the Cauchy kernel, single integrals, Clifford algebra and a whole-field approach. This is in contrast to many conventional techniques that are formulated in terms of Green's functions, double integrals, vector calculus and the combined field integral equation (CFIE). Whereas these conventional techniques lead to an implementation using the method of moments (MoM), the CCD technique is implemented as alternating projections onto convex sets in a Banach space. The ultimate outcome is an integral formulation that lends itself to a more direct and efficient solution than conventionally is the case, and applies without exception to all types...

NST and NST integration: nuclear science and technique and nano science and technique

International Nuclear Information System (INIS)

Zhao Yuliang; Chai Zhifang; Liu Yuanfang

2008-01-01

Nuclear science is considered as a big science and also the frontier in the 20 th century, it developed many big scientific facilities and many technique platforms (e.g., nuclear reactor, synchrotron radiation, accelerator, etc.) Nuclear Science and Technology (NST) provide us with many unique tools such as neutron beams, electron beams, gamma rays, alpha rays, beta rays, energetic particles, etc. These are efficient and essential probes for studying many technique and scientific issues in the fields of new materials, biological sciences, environmental sciences, life sciences, medical science, etc. Nano Science and Technology (NST) is a newly emerging multidisciplinary science and the frontier in the 21 st century, it is expected to dominate the technological revolution in diverse aspects of our life. It involves diverse fields such as nanomaterials, nanobiological sciences, environmental nanotechnology, nanomedicine, etc. nanotechnology was once considered as a futuristic science with applications several decades in the future and beyond. But, the rapid development of nanotechnology has broken this prediction. For example, diverse types of manufactured nanomaterials or nanostructures have been currently utilized in industrial products, semiconductors, electronics, stain-resistant clothing, ski wax, catalysts, other commodity products such as food, sunscreens, cosmetics, automobile parts, etc., to improve their performance of previous functions, or completely create novel functions. They will also be increasingly utilized in medicines for purposes of clinic therapy, diagnosis, and drug delivery. In the talk, we will discuss the possibility of NST-NST integration: how to apply the unique probes of advanced radiochemical and nuclear techniques in nanoscience and nanotechnology. (authors)

Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

Variance-reduction technique for Coulomb-nuclear thermalization of energetic fusion products in hot plasmas

International Nuclear Information System (INIS)

DeVeaux, J.C.; Miley, G.H.

1982-01-01

A variance-reduction technique involving use of exponential transform and angular-biasing methods has been developed. Its purpose is to minimize the variance and computer time involved in estimating the mean fusion product (fp) energy deposited in a hot, multi-region plasma under the influence of small-energy transfer Coulomb collisions and large-energy transfer nuclear elastic scattering (NES) events. This technique is applicable to high-temperature D- 3 He, Cat. D and D-T plasmas which have highly energetic fps capable of undergoing NES. A first application of this technique is made to a D- 3 He Field Reversed Mirror (FRM) where the Larmor radius of the 14.7 MeV protons are typically comparable to the plasma radius (plasma radius approx. 2 fp gyroradii) and the optimistic fp confinement (approx. 45% of 14.7 MeV protons) previously predicted is vulnerable to large orbit perturbations induced by NES. In the FRM problem, this variance reduction technique is used to estimate the fractional difference in the average fp energy deposited in the closed-field region, E/sub cf/, with and without NES collisions

A Technique for Controlling Matric Suction on Filter Papers . GroWth ...

African Journals Online (AJOL)

'Abstract. Moist filter papers are widely usedfor seed gennination tests but their water confent and matric suction are not usually controlled. A technique for controlling filter paper matric suction is described and usedfor germination studies involving fresh and aged sorghum seed (Sorghummcolor (L) Moench). Filter papers ...

Public involvement: the critical path in siting controversial facilities. Proceedings of the Nuclear Energy Low-Level Waste Mangement Program conference

International Nuclear Information System (INIS)

1986-01-01

The purpose of the conference was to: exchange information among those responsible for, or interested in, the development of new low-level waste disposal facilities; acquaint participants with past experiences of states and organizations in enfranchising the public in the siting of controversial facilities; and discuss various mechanisms and techniques for effectively involving the public in decision-making processes. The conference addressed four major topics: lessons from past experiences; mechanisms and techniques for public involvement, conflict resolution, and working constructively with the media. A series of presentations on each topic was followed by questions and discussion among presenters and conference participants. Several key points emerged as the conference proceeded

Hilar Parenchymal Oversew: a novel technique for robotic partial nephrectomy hilar tumor renorrhaphy.

Science.gov (United States)

Chavali, Jaya Sai S; Nelson, Ryan; Maurice, Matthew J; Kara, Onder; Mouracade, Pascal; Dagenais, Julien; Reese, Jeremy; Bayona, Pilar; Haber, Georges-Pascal; Stein, Robert J

2018-01-01

A renorrhaphy technique which is effective for hemostasis but does not place undue tension on the branch vessels of the renal sinus remains one of the challenging steps after hilar tumor resection during robotic partial nephrectomy (RPN). The published V-hilar suture (VHS) technique is one option for reconstruction after an RPN involving the hilum. The objective of this video is to show a novel renorrhaphy technique, Hilar Parenchymal Oversew that has been effective for such cases. We present two cases of RPN for renal hilar tumors. The first case depicts use of the VHS renorrhaphy technique for a tumor that abuts the renal hilum along 20% of its diameter. The second case demonstrates tumor resection and reconstruction for a tumor that has >50% involvement of the hilum along its diameter. After tumor resection, individual sinus vessels can be selectively oversewn with 2-0 Vicryl suture on SH needle. The remaining exposed parenchyma is controlled using the Hilar Parenchymal Oversew technique with a #0 Vicryl on CT-1 needle. For the Hilar Parenchymal Oversew surgery operative time was 225 min, estimated blood loss was 140 ml, warm ischemia time was 19 minutes, and there were no intraoperative complications. Pathology was consistent with clear cell renal cancer with negative margins. Robotic partial nephrectomy with the Hilar Parenchymal Oversew technique is a good alternative to VHS renorrhaphy in the management of renal hilar tumors "bulging" into the renal sinus with >50% of the tumor diameter abutting the hilum. Copyright® by the International Brazilian Journal of Urology.

Making Artificial Heart Components – Selected Aspects Of Casting Technology

Directory of Open Access Journals (Sweden)

Sobczak J.J.

2015-09-01

Full Text Available This study shown possibilities of Rapid Prototyping techniques (RP and metal casting simulation software (MCSS, including non inertial reference systems. RP and MCSS have been used in order to design and produce essential elements for artificial heart. Additionally it has been shown possibilities of Fused Deposition Modeling (FDM technique and DodJet technology using prototyped elements of rotodynamic pump. MAGMASOFT® software allowed to verify the cast kit heart valves model. Optical scanner Atos III enabled size verification of experimental elements supplied by rapid prototyping together with metal casting elements. Due to the selection of ceramic materials and assessment of molten metal – ceramic reactivity at high temperatures together with pattern materials selection model it was possible to design, manufacture a ceramic mould for titanium based alloys. The casting structure modification has been carried out by means of high isostatic pressure technique (HIP. The quality assessment of the casting materials has been performed using X-ray fluorescence (XRF, ARL 4460 Optical Emission Spectrometer, metallographic techniques and X-ray computed tomography.

The Development of a Differential Deposition Technique for Figure Correction in Grazing Incidence Optics

Data.gov (United States)

National Aeronautics and Space Administration — We propose the development of a physical-vapor-deposition coating technique to correct residual figure errors in grazing-incidence optics. The process involves...

Upgrading the alloy AlSi6Cu4 (AK64 cast to the ceramic mould

Directory of Open Access Journals (Sweden)

M. Dudyk

2007-12-01

Full Text Available In this article are presented the results of study on the kinetics of the crystallization processes in the refined, modified and filtered Silumin containing copper and the metallographic analysis of the obtained structures. Impact of the upgrading processes – refining, modification and filtration – of the studied alloy AK64 on changes of the impact strength KCV of the cast samples. Original metallographic analysis of the foam filters cast with the studied alloy was carried out. The efficiency of filtration mechanisms on improvement of quality and usefulness of the cast Silumin was demonstrated.

The equilibrium diagram and some properties of alloys Gd5Sb3-Tb5Sb3 system

International Nuclear Information System (INIS)

Azizov, Yu.S.; Abulkhaev, V.D.; Ganiev, I.N.

2001-01-01

The purpose of present work is investigation equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system in total range of concentrations. Equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system investigated by methods of difference-thermal, roentgen-phase and metallographic analyses. For the first time on the base of difference-thermal, roentgen-phase and metallographic analyses was formed the equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system. Was determined the cristal-chemical parameters of solid solutions with general formula Gd x Tb 5 - x Sb 3

A Simple Technique for Shoulder Arthrography

Energy Technology Data Exchange (ETDEWEB)

Berna-Serna, J.D.; Redondo, M.V.; Martinez, F.; Reus, M.; Alonso, J.; Parrilla, A.; Campos, P.A. [Virgen de la Arrixaca Univ. Hospital, El Palmar, Murcia (Spain). Dept. of Radiology

2006-09-15

Purpose: To present a systematic approach to teaching a technique for arthrography of the shoulder. Using an adhesive marker-plate with radiopaque coordinates, precise sites for puncture can be identified and the need for fluoroscopic guidance obviated. Material and Methods: Forty-six glenohumeral arthrograms were performed in 45 patients; in 1 case involving examination of both shoulders. The stages of the technique are described in detail, as are the fundamental aspects of achieving an effective glenohumeral injection. Pain intensity was measured in all patients using a verbal description scale. Results: Shoulder arthrography was successful in all cases. Average time taken for the procedure was 7 min, with no difference in the respective times required by an experienced radiologist and a resident. The procedure was well tolerated by most patients, with slight discomfort being observed in a very few cases. Conclusion: The arthrographic technique used in this study is simple, safe, rapid, and reproducible, and has the advantage of precise localization of the site for puncture without need for fluoroscopic guidance. The procedure described in this study can be of help in teaching residents and can reduce the learning curve for radiologists with no experience in arthrographic methods. It also reduces the time of exposure to fluoroscopy Keywords: Arthrography, joint, shoulder.

Wide Panel Testing Technique for Evaluating Repair Weld Strengths

Science.gov (United States)

Rogers, Patrick R.; Bynum, Julian E.; Shah, Sandeep R.

1998-01-01

This paper describes a new tensile testing technique for evaluating the overall effect of a repair weld on the strength of a welded joint. Previously, repair weld strengths have been evaluated using one-inch width tensile specimens, but this technique does not capture all of the effects that result from a repair. The new technique involves testing of "wide panel" tensile specimens which contain the full length of a repair weld within a longer initial weld, allowing the specimen to capture the combined effects of residual stresses, local strength degradation, and load redistribution around a repair. The development of strains in the repair area of standard aluminum alloy specimens and new high-performance aluminum-lithium alloy specimens was observed and evaluated using photoelastic material. The results of this evaluation show an increased sensitivity to repair welding residual stresses in the aluminum-lithium alloy specimens.

Cerebral blood flow measurement techniques in infants and children

International Nuclear Information System (INIS)

Kirsch, J.R.; Traystman, R.J.; Rogers, M.C.

1985-01-01

The tremendous growth of interest in neurologic intensive care and in the pathophysiology of the cerebral circulation in the past few years has resulted in increasing numbers of studies that document alterations in cerebral flow during the course of various diseases or as a response to treatment of them. Before pediatricians come to conclusions based on these studies, it is important to have an understanding of the techniques involved. The techniques are complex and difficult but are based on understandable principles. They also have limitations and are subject to misinterpretations. Pediatricians should become knowledgeable about some of these techniques and their limitations because it is likely that they will be applied with increasing frequency in the next several years. We are on the threshold of exciting discoveries in abnormalities of cerebral blood flow and cerebral metabolism not only in critically ill children but also in children with congenital and learning disorders

Considering Mindfulness Techniques in School-based Anti-bullying Programmes

Directory of Open Access Journals (Sweden)

Mairead Foody

2018-01-01

Full Text Available Schools have a duty of care to all students and to directly prevent and intervene with bullying amongst children and adolescents. The emergence of cyberbullying escalates this responsibility as the strategies that have become appropriate at national levels for bullying do not always parallel over to online environments. The impact on mental health is the most obvious concern for those responsible for reducing bullying, however, input from psychologists and mental health professionals is scant and often limited on this topic. This paper outlines what bullying is and the devastating impact it can have on the mental health of those involved. It will outline the most common anti-bullying initiatives as well as the current psychological and educational techniques, which could also be used to alleviate distress associated with bullying involvement. We will focus specifically on the role of mindfulness techniques and argue for more of such exercises to be included in whole-school bullying programmes. We conclude by arguing the need to investigate components relevant to both mindfulness and anti-bullying programmes (e.g., empathy, perspective-taking as active ingredients for reducing the impact of bullying on mental health.

SU-E-T-622: Planning Technique for Passively-Scattered Involved-Node Proton Therapy of Mediastinal Lymphoma with Consideration of Cardiac Motion

Energy Technology Data Exchange (ETDEWEB)

Flampouri, S; Li, Z; Hoppe, B [University of Florida Health Proton Therapy Institute, Jacksonville, FL (United States)

2015-06-15

Purpose: To develop a treatment planning method for passively-scattered involved-node proton therapy of mediastinal lymphoma robust to breathing and cardiac motions. Methods: Beam-specific planning treatment volumes (bsPTV) are calculated for each proton field to incorporate pertinent uncertainties. Geometric margins are added laterally to each beam while margins for range uncertainty due to setup errors, breathing, and calibration curve uncertainties are added along each beam. The calculation of breathing motion and deformation effects on proton range includes all 4DCT phases. The anisotropic water equivalent margins are translated to distances on average 4DCT. Treatment plans are designed so each beam adequately covers the corresponding bsPTV. For targets close to the heart, cardiac motion effects on dosemaps are estimated by using a library of anonymous ECG-gated cardiac CTs (cCT). The cCT, originally contrast-enhanced, are partially overridden to allow meaningful proton dose calculations. Targets similar to the treatment targets are drawn on one or more cCT sets matching the anatomy of the patient. Plans based on the average cCT are calculated on individual phases, then deformed to the average and accumulated. When clinically significant dose discrepancies occur between planned and accumulated doses, the patient plan is modified to reduce the cardiac motion effects. Results: We found that bsPTVs as planning targets create dose distributions similar to the conventional proton planning distributions, while they are a valuable tool for visualization of the uncertainties. For large targets with variability in motion and depth, integral dose was reduced because of the anisotropic margins. In most cases, heart motion has a clinically insignificant effect on target coverage. Conclusion: A treatment planning method was developed and used for proton therapy of mediastinal lymphoma. The technique incorporates bsPTVs compensating for all common sources of uncertainties

Operational procedure standard for occurrences involving radioactive materials

International Nuclear Information System (INIS)

Piekarz, Leonardo; Rezende, Talita C.; Pinheiro, Christiano J.G.

2017-01-01

This study has as objective to analyze more deeply the actions of response to emergencies involving radioactive materials, in the intent to establish a pattern to the actions performed by the military fire fighters of the Military Fire Brigade of Minas Gerais. To met these goals, it has been attempted to analyze the procedures utilized and recommended, nowadays, for the military fire fighters of CBMMG, and through directed studies, to suggest new actions possible to be executed in the local of the emergency in a way that will not expose the garrison to doses of ionizing radiation that may prejudice them. It is a study of bibliographic, exploratory, and also descriptive nature, realized through a qualitative approach. The techniques used for the research were the analysis of institutional documents, norms and other literature produced by renamed entities in the radiologic and biosafety areas. It was then concluded that CBMMG, through simple actions of response, can provide higher quality and safety in the operations involving radiologic accidents, standing out that the implemented actions nowadays are very beneath the capacity of the corporation, due to the lack of knowledge of the matter by the fire fighters. It was proposed, then, that new actions be implemented and instituted as operational procedures to be used on those emergencies, with the objective of provide a higher safety and professionalism in the attendance to emergencies involving radioactive materials. (author)

Operational procedure standard for occurrences involving radioactive materials

Energy Technology Data Exchange (ETDEWEB)

Piekarz, Leonardo, E-mail: leonardopbm@yahoo.com.br [Academia de Bombeiros Militar de Minas Gerais, Belo Horizonte, MG (Brazil); Rezende, Talita C.; Pinheiro, Christiano J.G., E-mail: talitacolombi@yahoo.com, E-mail: christrieste@yahoo.it [Universidade Federal do Espirito Santo (CCA/UFES), Alegre, ES (Brazil). Programa de Pós-Graduação em Engenharia Química

2017-07-01

This study has as objective to analyze more deeply the actions of response to emergencies involving radioactive materials, in the intent to establish a pattern to the actions performed by the military fire fighters of the Military Fire Brigade of Minas Gerais. To met these goals, it has been attempted to analyze the procedures utilized and recommended, nowadays, for the military fire fighters of CBMMG, and through directed studies, to suggest new actions possible to be executed in the local of the emergency in a way that will not expose the garrison to doses of ionizing radiation that may prejudice them. It is a study of bibliographic, exploratory, and also descriptive nature, realized through a qualitative approach. The techniques used for the research were the analysis of institutional documents, norms and other literature produced by renamed entities in the radiologic and biosafety areas. It was then concluded that CBMMG, through simple actions of response, can provide higher quality and safety in the operations involving radiologic accidents, standing out that the implemented actions nowadays are very beneath the capacity of the corporation, due to the lack of knowledge of the matter by the fire fighters. It was proposed, then, that new actions be implemented and instituted as operational procedures to be used on those emergencies, with the objective of provide a higher safety and professionalism in the attendance to emergencies involving radioactive materials. (author)

What do potential jurors know about police interrogation techniques and false confessions?

Science.gov (United States)

Leo, Richard A; Liu, Brittany

2009-01-01

Psychological police interrogation methods in America inevitably involve some level of pressure and persuasion to achieve their goal of eliciting confessions of guilt from custodial suspects. In this article, we surveyed potential jurors about their perceptions of a range of psychological interrogation techniques, the likelihood that such techniques would elicit a true confession from guilty suspects, and the likelihood that such techniques could elicit a false confession from innocent suspects. Participants recognized that these interrogation techniques may be psychologically coercive and may elicit true confessions, but believed that psychologically coercive interrogation techniques are not likely to elicit false confessions. The findings from this survey study indicate that potential jurors believe that false confessions are both counter- intuitive and unlikely, even in response to psychologically coercive interrogation techniques that have been shown to lead to false confessions from the innocent. This study provides empirical support for the idea that expert witnesses may helpfully inform jurors about the social science research on psychologically coercive interrogation methods and how and why such interrogation techniques can lead to false confessions. (c) 2009 John Wiley & Sons, Ltd.

Teaching Techniques, Types of Personality, and English Listening Skill

Directory of Open Access Journals (Sweden)

Ni Made Ratminingsih

2013-01-01

Full Text Available Abstract: Teaching Techniques, Types of Personality, and English Listening Skill. This study inves­tigated the effect of teaching techniques and types of personality on English listening skill. This experi­mental study involved 88 students under investigation, which were determined randomly through multi-stage random sampling technique. The results of the research indicate that there is an interaction effect between the teaching techniques and types of personality on the English listening skill; there is no significant difference in the listening skill between the group of students who learn using the game technique and those who learn using the song technique; the listening skill of students having extrovert personality is better than those having introvert personality; the listening skill of students having extrovert personality who learn using the game technique is lower than those who learn using the song technique; and the listen­ing skill of students having introvert personality who learn using the game technique is higher than those who learn using the song technique. Abstrak: Teknik Pembelajaran, Tipe Kepribadian, dan Keterampilan Mendengarkan Bahasa Inggris. Penelitian ini bertujuan untuk mengetahui pengaruh teknik pembelajaran dan tipe kepribadian terhadap keterampilan mendengarkan bahasa Inggris. Penelitian ini melibatkan 88 orang siswa, yang ditentukan secara acak melalui multi stage random sampling technique. Hasil penelitian menunjukkan bahwa terdapat pengaruh interaksi antara teknik pembelajaran dan tipe kepribadian terhadap keterampilan mendengarkan bahasa Inggris; tidak terdapat perbedaan yang signifikan pada keterampilan mendengarkan antara siswa yang belajar dengan teknik pembelajaran permainan dan lagu; keterampilan mendengarkan siswa yang berkepribadian ekstroversi lebih baik daripada yang berkepribadian introversi; keterampilan mendengarkan siswa yang berkepribadian ekstroversi, yang belajar dengan teknik pembelajaran

A Technique for Controlling Matric Suction on Filter Papers Used in ...

African Journals Online (AJOL)

Moist filter papers are widely usedfor seed gennination tests but their water confent and matric suction are not usually controlled. A technique for controlling filter paper matric suction is described and usedfor germination studies involving fresh and aged sorghum seed (Sorghummcolor (L) Moench). Filter papers wetted to ...

Headspace techniques in foods, fragrances and flavors: an overview.

Science.gov (United States)

Rouseff, R; Cadwallader, K

2001-01-01

Headspace techniques have traditionally involved the collection of volatiles in the vapor state under either dynamic or static conditions as a means of determining concentrations in the product of interest. A brief overview of contemporary headspace applications and recent innovations are presented from the literature and Chapters in this book. New approaches used to concentrate volatiles under static conditions such as solid phase micro extraction, SPME, are examined. Advances in purge and trap applications and automation are also presented. Innovative methods of evaluating headspace volatiles using solid state sensor arrays (electronic noses) or mass spectrometers without prior separation are referenced. Numerous food and beverage headspace techniques are also reviewed. Advantages, limitations and alternatives to headspace analysis are presented.

The Involved Ostrich

DEFF Research Database (Denmark)

Davies, Andrea; Dobscha, Susan; Geiger, Susi

2008-01-01

that the transition into parenthood can be difficult for men due to their lack of a physical connection to the pregnancy, a perception that the baby industry is not designed for them, the continuance of male stereotypes in the media, and also the time available to men to become involved in consumption activities......-natal data. Data revealed that men, according to their partner’s perceptions, used consumption as a virtual umbilical cord, although levels of consumption involvement varied from co-involvement for most purchases, to limited involvement, and/or involvement for ‘large’ items, particularly travel systems...... and technical items. This research also revealed that men partook in highly masculinized forms of “nesting,” and in general shunned pregnancy book reading; although some did engage in “research” activities such as searching the internet for product safety information. We conclude from this study...

Impacts of Pre-Retirement Guidance and Family Involvement on Retirement Adjustment of Retirees in Nigeria

Directory of Open Access Journals (Sweden)

O.O. Olatomide

2017-12-01

Full Text Available The study examined retirement adjustment of teacher-retirees in Osun State, and explored the interaction effects of pre-retirement guidance and family in-volvement on retirement adjustment. Exposit-facto design was used. The population comprised retirees from public, civil and private establishments from which 122 teacher-retirees were selected using a multi-stage sampling technique. An instrument: Family Involvement, Pre-retirement Guidance and Retirement Adjustment Questionnaire was used for data collection. Three research questions and three hypotheses guided the study. Data were analyzed using descriptive and inferential statistics. Results revealed that retirees in Osun State are not optimally adjusted, and positive significant interaction effect was found between family involvement and pre-retirement guidance on retirees adjustment, among others. Appropriate policy implications are outlined.

Langerhans' cell histiocytosis: pathology, imaging and treatment of skeletal involvement

Energy Technology Data Exchange (ETDEWEB)

Azouz, E. Michel [University of Miami, Pediatric Radiology Section, Department of Radiology, Miami, FL (United States); Saigal, Gaurav [McGill University, Department of Medical Imaging, Quebec (Canada); Rodriguez, Maria M. [University of Miami, Department of Pathology, Miami, FL (United States); Podda, Antonello [University of Miami, Division of Pediatric Hematology/Oncology, Miami, FL (United States)

2005-02-01

Langerhans' cell histiocytosis (LCH) is manifested in a variety of ways, the most common being the eosinophilic granuloma, a localized, often solitary bone lesion that occurs predominantly in the pediatric age group. The hallmark of LCH is the proliferation and accumulation of a specific histiocyte: the Langerhans' cell. In bone this may cause pain and adjacent soft-tissue swelling, but some lesions are asymptomatic. LCH can involve any bone, but most lesions occur in the skull (especially the calvarium and temporal bones), the pelvis, spine, mandible, ribs, and tubular bones. Imaging diagnosis of the disease in bone is first based on the plain radiographic appearance, which is usually a central destructive, aggressive-looking lesion. In the skull, the lesions develop in the diploic space, are lytic, and their edges may be beveled, scalloped or confluent (geographic), or show a ''button sequestrum.'' Vertebral body involvement usually causes collapse, resulting in vertebra plana. With significant recent improvements in the quality of gamma cameras, imaging techniques, and in studying children, bone scintigraphy at diagnosis and on follow-up usually reveals the sites of active disease, especially when the involvement is polyostotic. CT and MR imaging are very useful in providing detailed cross-sectional anatomic detail of the involved bone, including the bone marrow and the adjacent soft tissues. CT is better suited for demonstrating bone detail and MR imaging for bone marrow and soft-tissue involvement. (orig.)

Decision Analysis Technique

Directory of Open Access Journals (Sweden)

Hammad Dabo Baba

2014-01-01

Full Text Available One of the most significant step in building structure maintenance decision is the physical inspection of the facility to be maintained. The physical inspection involved cursory assessment of the structure and ratings of the identified defects based on expert evaluation. The objective of this paper is to describe present a novel approach to prioritizing the criticality of physical defects in a residential building system using multi criteria decision analysis approach. A residential building constructed in 1985 was considered in this study. Four criteria which includes; Physical Condition of the building system (PC, Effect on Asset (EA, effect on Occupants (EO and Maintenance Cost (MC are considered in the inspection. The building was divided in to nine systems regarded as alternatives. Expert's choice software was used in comparing the importance of the criteria against the main objective, whereas structured Proforma was used in quantifying the defects observed on all building systems against each criteria. The defects severity score of each building system was identified and later multiplied by the weight of the criteria and final hierarchy was derived. The final ranking indicates that, electrical system was considered the most critical system with a risk value of 0.134 while ceiling system scored the lowest risk value of 0.066. The technique is often used in prioritizing mechanical equipment for maintenance planning. However, result of this study indicates that the technique could be used in prioritizing building systems for maintenance planning

Review of the Potential of the Ni/Cu Plating Technique for Crystalline Silicon Solar Cells

Directory of Open Access Journals (Sweden)

Atteq ur Rehman

2014-02-01

Full Text Available Developing a better method for the metallization of silicon solar cells is integral part of realizing superior efficiency. Currently, contact realization using screen printing is the leading technology in the silicon based photovoltaic industry, as it is simple and fast. However, the problem with metallization of this kind is that it has a lower aspect ratio and higher contact resistance, which limits solar cell efficiency. The mounting cost of silver pastes and decreasing silicon wafer thicknesses encourages silicon solar cell manufacturers to develop fresh metallization techniques involving a lower quantity of silver usage and not relying pressing process of screen printing. In recent times nickel/copper (Ni/Cu based metal plating has emerged as a metallization method that may solve these issues. This paper offers a detailed review and understanding of a Ni/Cu based plating technique for silicon solar cells. The formation of a Ni seed layer by adopting various deposition techniques and a Cu conducting layer using a light induced plating (LIP process are appraised. Unlike screen-printed metallization, a step involving patterning is crucial for opening the masking layer. Consequently, experimental procedures involving patterning methods are also explicated. Lastly, the issues of adhesion, back ground plating, process complexity and reliability for industrial applications are also addressed.

Comprehensive investigation of the metal in drums of boilers at thermal power stations

Science.gov (United States)

Ozhigov, L. S.; Mitrofanov, A. S.; Tolstolutskaya, G. D.; Vasilenko, R. L.; Rudenko, A. G.; Ruzhytskyi, V. V.; Ribalchenko, N. D.; Shramchenko, S. V.

2017-05-01

A comparative investigation of the metal of drums of two TP-100 boilers at the Starobeshevskaya and the Lugansk thermal power stations (TPS) was performed. Their operation time was approximately 300000 hours; the shell of one drum was ruptured during a hydraulic test, and the other drum is in operation. According to the results of the technical diagnostics and a strength analysis, both drums comply with the applicable regulatory requirements. The objects of the investigation were fragments of the ruptured drum and a "plug" cut out of the shell during a scheduled inspection. The investigation was carried out by microscopic metallography methods and the scanning electron microscopy technique. Mechanical tests of metal specimens were performed, and the hydrogen content in these specimens was measured. Prior to the material research, the metal was examined using a magnetic memory method. The investigation yielded specifics of the metal microstructure, mechanical properties, and fracture patterns of the metal specimens at various temperatures. An investigation performed by the method of thermal-desorption mass spectrometry revealed no considerable difference in the hydrogen content in the metal of both drums, thereby excluding the effect of hydrogenation in analyzing the rupture causes. It was established that the drum at the Starobeshevskaya TPS had been damaged due to its low impact strength at room temperature and high brittle-ductile transition point. Comparison of the metallographic study data with the results obtained using the magnetic memory method suggests that the fracture was caused by local formation of the Widmannstatten pattern at points where accessories are welded to the shell. The prospects are demonstrated of the comprehensive approach to nondestructive examination (NDE) of TPS drums using the magnetic memory technique and metallographic methods.

The Influence of Sports Celebrity Credibility on Purchase Intention: The Moderating Effect of Gender and Consumer Sports-Involvement

Directory of Open Access Journals (Sweden)

Natalie Bragança Düsenberg

2016-01-01

Full Text Available This study investigates the effects of sport’s celebrity endorsement on purchase intention. More specifically, this study seeks to (1 identify the extent to which the sports celebrity’s credibility influences consumer purchase intention; (2 the extent to which gender moderates the effect of sports celebrity endorsement on purchase intention; and (3 to what extent consumer sports-involvement moderates the effect of a sports celebrity endorsement on purchase intention. One famous Brazilian soccer player and four product categories were used as stimuli. The research method used was a survey, which has included 1,025 respondents. Data analysis was performed using exploratory factor analysis (EFA and confirmatory factor analysis (CFA. Structural equation modeling (SEM, using the ADF technique, was applied to test the substantive hypotheses. To test the hypotheses of the moderating effect of gender and consumer sports-involvement, the research used the multigroup analysis technique. The empirical results support the relationship between a sport celebrity’s endorsement and purchase intention. The moderating effects of gender and sports-involvement were also empirically supported, but only partially.

Techniques for Investigating Molecular Toxicology of Nanomaterials.

Science.gov (United States)

Wang, Yanli; Li, Chenchen; Yao, Chenjie; Ding, Lin; Lei, Zhendong; Wu, Minghong

2016-06-01

Nanotechnology has been a rapidly developing field in the past few decades, resulting in the more and more exposure of nanomaterials to human. The increased applications of nanomaterials for industrial, commercial and life purposes, such as fillers, catalysts, semiconductors, paints, cosmetic additives and drug carriers, have caused both obvious and potential impacts on human health and environment. Nanotoxicology is used to study the safety of nanomaterials and has grown at the historic moment. Molecular toxicology is a new subdiscipline to study the interactions and impacts of materials at the molecular level. To better understand the relationship between the molecular toxicology and nanomaterials, this review summarizes the typical techniques and methods in molecular toxicology which are applied when investigating the toxicology of nanomaterials and include six categories: namely; genetic mutation detection, gene expression analysis, DNA damage detection, chromosomal aberration analysis, proteomics, and metabolomics. Each category involves several experimental techniques and methods.

10 years of 1:1 taping in Belgium - A selection of murder cases involving fibre examination.

Science.gov (United States)

De Wael, K; Lepot, L; Lunstroot, K; Gason, F

2016-01-01

Since 2002, the 1:1 tape lifting technique on murder victims has been introduced in Belgium. Thirty-six murder cases for which a fibre examination was carried out in our laboratory between 2002 and 2012 are reviewed. These cases all involved the collection of microtraces on 39 victims using a 1:1 taping or similar technique, called semi 1:1 taping. The degree of "positive outcomes" for investigative and comparative fibre cases is high. Especially in cases where the modus operandi of suspects had to be verified, the examination of the 1:1 tape lifting led to very useful fibre results. The findings from some of these fibre cases are used to illustrate the advantages, drawbacks and points of interest of the two collection techniques. These are also compared with the zonal taping technique, another microtrace collection technique applied on victims at the crime scene. Copyright © 2015 The Chartered Society of Forensic Sciences. Published by Elsevier Ireland Ltd. All rights reserved.

Techniques for site investigations for underground disposal of radioactive wastes

International Nuclear Information System (INIS)

1985-01-01

The report provides a more detailed description of the capabilities and applications of the various earth science investigation techniques outlined in the IAEA Technical Reports Series Nos. 177, 215 and 216. These methods are generally appropriate during at least one of the stages of the assessment or selection of a site for any type of waste disposal facility, in shallow ground or in deep geological formations. This report is addressed to technical authorities responsible for or involved in planning, approving, executing and reviewing national waste disposal programmes. It may also help administrative authorities in this field to select appropriate techniques for obtaining the majority of the required information at minimum cost

Artifact Elimination Technique in Tomogram of X-ray Computed Tomography

International Nuclear Information System (INIS)

Rasif Mohd Zain

2015-01-01

Artifacts of tomogram are main commonly problems occurred in x-ray computed tomography. The artifacts will be appearing in tomogram due to noise, beam hardening, and scattered radiation. The study has been carried out using CdTe time pix detector. The new technique has been developed to eliminate the artifact occurred in hardware and software. The hardware setup involved the careful alignment all of the components of the system and the introduction of a collimator beam. Meanwhile, in software development deal with the flat field correction, noise filter and data projection algorithm. The results show the technique developed produce good quality images and eliminate the artifacts. (author)

Validation of a technique of measurement in vivo of 131I in thyroids

International Nuclear Information System (INIS)

Villella, A.M.; Puerta Yepes, N.; Gossio, S.; Papadopulos, S.

2010-01-01

The Total Body Counter (TBC) Laboratory of the Nuclear Regulatory Authority, following the institutional initiative of quality assurance in its measurement techniques, has been involved in an accreditation process based on the ISO/IEC 17205:2005 norm. In vivo measurement of 131 I in thyroid has been selected as the first technique in this process, and it is described in this paper. The TBC Laboratory uses for this technique a gamma spectrometry system with a NaI(Tl) detector, calibrated with a neck simulator of the IRD and a certified plane source of 131 I with thyroid form. It has been carried out a validation plan that has permitted the characterization of the 131 I measurement technique, and its uncertainty evaluation. Measurement parameters that affect the uncertainty are discussed and recommendations for the technique optimization are proposed. (authors) [es

Effect of Shot Peening on the Fatigue Strength of Automotive Tubular Stabilizer Bars DC 218

Directory of Open Access Journals (Sweden)

Wittek A.M.

2016-12-01

Full Text Available This paper concerns issues related to the development of designs of stabilizer bars for new motor vehicle models. It involves not only the designing of a stabilizer bar with the shape required by the manufacturer, but also the preparation of bending and heat treatment processes as well as the performance of strength and fatigue tests. In the prototype development phase, the simulations techniques (FEM may be used to assess the design. The article contains a detailed analysis of a stabilizer bar designated with the DC 218 VA symbol. Performed numerical strength and fatigue calculations showed that the developed stabilizer bar design with the desired shape did not achieve the required number of fatigue cycles. It was also proven at the test stand by testing a prototype stabilizer bar. Therefore, it was suggested to supplement the technological process with an additional shot peening operation whose main aim was to reduce the length of microcracks on the stabilizer bar’s surface. This effect was confirmed during comparative metallographic tests of not shot – peened and shot – peened stabilizer bars. After shot peening, the analysed stabilizer bar reached a fatigue strength which exceeded the limits set by the manufacturer.

Preparation, structure and properties of hafnium compounds in the system Hf-C-N-O

International Nuclear Information System (INIS)

Brundiers, G.D.

1975-08-01

Highly dense, homogenous and single phase hafnium carbonitride samples (with low oxygen content) were prepared in the whole concentration range of the ternary cubic carbonitrides. Stoichiometric hafnium oxicarbides were also prepared within the range of solubility. The procedure involved the hot pressing of powders of HfC, HfN, Hf, Hf-Oxide and carbon at temperatures of 3,000 0 C and pressures up to 550 kpf/cm 2 using a novel technique. Small single crystals of slightly substoichiometric HfN were also repared. The densification of the powders was studied as a function of the non-metal concentration. Carbonitrides with N/Hf ratio of 0.37 were prepared in a high temperature autoclave operating at medium pressures by the reaction of HfC with nitrogen. All the samples were characterized by density measurements, chemical, X-ray and metallographic analysis and in some cases with the aid of quantitative metallography and microprobe analysis. Typical properties investigated were lattice parameter, thermal expansion, microhardness and electrical resistivity as function of the non-metal content. For specific concentrations extreme values in the properties are attained. With the aid of the valence electron concentration (VEC) parameter, the properties can be correlated with the density of states of electrons at the Fermi level. (orig./HK) [de

Subsea flowlines installation: new techniques are ready for use

Energy Technology Data Exchange (ETDEWEB)

Borelli, A.

1978-01-01

A discussion of the new offshore pipelaying methods developed and tested by ETPM (together with other French companies) covers a description, the technical characteristics, conditions of applicability, and data on testing for towing methods, i.e., for surface and subsurface tow techniques which involve onshore construction of pipe segments, towing to the offshore site, and immersion of the segments, e.g., by using the ''draw-down'' technique, which was developed for Mobil Research and Develoment Corp., and can be used for up to 10,000 ft pipe sections at up to 6000 ft depths; and the near-the-bottom tow technique tested on a full scale in May 1977 by Compagnie Francaise des Petroles in the Mediterranean with 1 km, 8 in. + 4 in. pipe bundles, in which two tugs tow a pipeline section, typically at 10 ft above the sea bottom, on guide ropes; and the ''J-curve'' laying method.

Analytical techniques for measurement of 99Tc in environmental samples

International Nuclear Information System (INIS)

Anon.

1979-01-01

Three new methods have been developed for measuring 99 Tc in environmental samples. The most sensitive method is isotope dilution mass spectrometry, which allows measurement of about 1 x 10 -12 grams of 99 Tc. Results on analysis of five samples by this method compare very well with values obtained by a second independent method, which involves counting of beta particles from 99 Tc and internal conversion electrons from /sup 97m/Tc. A third method involving electrothermal atomic absorption has also been developed. Although this method is not as sensitive as the first two techniques, the cost per analysis is expected to be considerably less for certain types of samples

Development and applications of microanalytical techniques

International Nuclear Information System (INIS)

Cholewa, M.

2005-05-01

The development of new analytical techniques is an essential part of our everyday life and is dictated by strong progress in modern science and technology. Both these areas require more precise information about materials and processes involved. Due to these requirements we have been observing a rapid growth in the development of techniques that require both a high spatial resolution and high sensitivity. Modern analytical techniques provide an important interface between science and applications. The works presented in this habilitation thesis span the period of almost 20 years. During this time the author has been leading the development and applications of several new analytical and micro analytical techniques which have been documented in this thesis. This development has required development of ideas, strong leadership, organisational skills, organisation of funds and groups to carry out the necessary work. In chapter 3 the use of the PIXE and XANES techniques described an investigation of permeability for selected elements inside cells. It was important to develop new protocols for sample preparation and analysis and a large number of cells were necessary in order to obtain meaningful data. This development was closely associated with work presented in chapter 4 where the role of sample damage under the MeV ion beam bombardment was investigated. At that time we were the leading group in the world to perform such studies. Chapter 5 describes development of new analytical techniques and its possible applications. Development of the SIHF has been probably the most demanding and difficult project and was described in chapter 6 and it was closely related with development of a diamond detector described in chapter 7. A great part of these works were performed by the author at the Micro Analytical Research Centre (MARC) in the School of Physics at the University of Melbourne in Australia. However, some works were performed at GSI in Germany and BNL in USA. (author)

Surgical implantation techniques for electronic tags in fish

Energy Technology Data Exchange (ETDEWEB)

Wagner, Glenn N.; Cooke, Steven J.; Brown, Richard S.; Deters, Katherine A.

2011-01-01

Intracoelomic implantation of transmitters into fish requires making a surgical incision, incision closure, and other surgery related techniques; however, the tools and techniques used in the surgical process vary widely. We review the available literature and focus on tools and techniques used for conducting surgery on juvenile salmonids because of the large amount of research that is conducted on them. The use of sterilized surgical instruments properly selected for a given size of fish will minimize tissue damage and infection rates, and speed the wound healing of fish implanted with transmitters. For the implantation of transmitters into small fish, the optimal surgical methods include making an incision on the ventral midline along the linea alba (for studies under 1 month), protecting the viscera (by lifting the skin with forceps while creating the incision), and using absorbable monofilament suture with a small-swaged-on swaged-on tapered or reverse-cutting needle. Standardizing the implantation techniques to be used in a study involving particular species and age classes of fish will improve survival and transmitter retention while allowing for comparisons to be made among studies and across multiple years. This review should be useful for researchers working on juvenile salmonids and other sizes and species of fish.

[THE FORMS OF DELIBERATION INVOLVED IN THE FIELD OF BIOETHICS: TECHNIQUE DELIBERATION AND ETHICS DELIBERATION].

Science.gov (United States)

Neves Pinto, Gerson

2015-12-01

In this article the author examines the formulation of the problem of new technologies with their ethical limits and legal. To do this, in a first it is d'assess the contribuitions of the two most important contemporary philosophers who have treated this subject: Jürgen Habermas and Ronald Dworkin, while trying to put them into dialog with the one who has been one of the founders of l'classic ethics: Aristotle. Then, it tries to answer the question of how could we understand this notion that Dworkin nome "moral dislocation" between the random and the choice or well, as the appointed Habermas, "l'extension of the contingency". Finally, we questioned how the Aristotelian distinction between the technical deliberation and deliberative ethical-moral can contribute to a better understanding of the questions on the decisions and choices that will make the moral agents (such as patients or the judges), as well as those relating to the type of deliberation technique chosen by the doctor or by the health professional.

INNOVATIVE TECHNIQUES USED BY EPA, SCDHEC, AND DOE TO INCREASE STAKEHOLDER AND PUBLIC INVOLVEMENT IN THE CLEANUP OF NUCLEAR PRODUCTION FACILITIES

International Nuclear Information System (INIS)

Mccollum, L

2007-01-01

This paper will describe the importance of public and stakeholder involvement to the decisions being made at Savannah River Site (SRS) regarding the cleanup of major production facilities. For over a decade the Department of Energy (DOE), the U.S. Environmental Protection Agency (EPA) and the South Carolina Department of Health and Environmental Control (SCDHEC) have operated under a three party agreement (known as the Federal Facilities Agreement or FFA) to clean up the SRS from the remnants of the Cold War plutonium production at SRS. During this time, the 3 agencies have consulted with the surrounding and impacted public to gain stakeholder input on the decisions concerning the clean up of various wastes at the SRS. The primary instrument of public input has been and remains the SRS Community Advisory Board (CAB). Much progress has been made over the years in cleaning up the SRS and the CAB has provided invaluable stakeholder input. Many planned decisions have been modified and changed as a result of the input of the CAB. Recently, DOE has decided to move forward with the Decommissioning of excess facilities at the SRS. These facilities include many buildings involved in the various missions of radioactive isotope production at the SRS, including the reactors and the plutonium processing facilities. The discussions of the 3 agencies on how to best accomplish this work have always included discussions about how to best involve and receive input from all stakeholders. The innovative way the 3 agencies have worked together through the public involvement format has application nationally and DOE-Complex wide. The decisions made will impact the surrounding community and the country for years. Multiple meetings with the CAB and other stakeholders will be required and it will be incumbent on the 3 agencies to reach out to and involve all interested parties. At least 3 different approaches could be used for stakeholder involvement. (1) a typical CERCLA ''proposed plan

Conventional and dense gas techniques for the production of liposomes: a review.

Science.gov (United States)

Meure, Louise A; Foster, Neil R; Dehghani, Fariba

2008-01-01

The aim of this review paper is to compare the potential of various techniques developed for production of homogenous, stable liposomes. Traditional techniques, such as Bangham, detergent depletion, ether/ethanol injection, reverse-phase evaporation and emulsion methods, were compared with the recent advanced techniques developed for liposome formation. The major hurdles for scaling up the traditional methods are the consumption of large quantities of volatile organic solvent, the stability and homogeneity of the liposomal product, as well as the lengthy multiple steps involved. The new methods have been designed to alleviate the current issues for liposome formulation. Dense gas liposome techniques are still in their infancy, however they have remarkable advantages in reducing the use of organic solvents, providing fast, single-stage production and producing stable, uniform liposomes. Techniques such as the membrane contactor and heating methods are also promising as they eliminate the use of organic solvent, however high temperature is still required for processing.

Accuracy of 3 different impression techniques for internal connection angulated implants.

Science.gov (United States)

Tsagkalidis, George; Tortopidis, Dimitrios; Mpikos, Pavlos; Kaisarlis, George; Koidis, Petros

2015-10-01

Making implant impressions with different angulations requires a more precise and time-consuming impression technique. The purpose of this in vitro study was to compare the accuracy of nonsplinted, splinted, and snap-fit impression techniques of internal connection implants with different angulations. An experimental device was used to allow a clinical simulation of impression making by means of open and closed tray techniques. Three different impression techniques (nonsplinted, acrylic-resin splinted, and indirect snap-fit) for 6 internal-connected implants at different angulations (0, 15, 25 degrees) were examined using polyether. Impression accuracy was evaluated by measuring the differences in 3-dimensional (3D) position deviations between the implant body/impression coping before the impression procedure and the coping/laboratory analog positioned within the impression, using a coordinate measuring machine. Data were analyzed by 2-way ANOVA. Means were compared with the least significant difference criterion at Pimpression technique exhibited a higher accuracy than the other techniques studied when increased implant angulations at 25 degrees were involved. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

A radioanalytical technique using (n,2n) reaction for the elemental analysis of samples

International Nuclear Information System (INIS)

Labor, M.

1985-11-01

A technique to determine elemental composition of samples is reported. The principle of the technique employs the internal standard method and involves the resolution of complex annihilation spectra. The technique has been applied to the determination of the mass of nitrogen, msub(N), and that of potassium, msub(K), in known masses of potassium nitrate. The percentage difference between the calculated mass and actual masses in 2g and 3g of potassium nitrate is 1.0 and 0.7 respectively for potassium, and 1.0 for nitrogen. The use of more simultaneous equations than necessary in solving for msub(N) and msub(K) offers one of the advantages of the technique. (author)

Comparison between correlated sampling and the perturbation technique of MCNP5 for fixed-source problems

International Nuclear Information System (INIS)

He Tao; Su Bingjing

2011-01-01

Highlights: → The performance of the MCNP differential operator perturbation technique is compared with that of the MCNP correlated sampling method for three types of fixed-source problems. → In terms of precision, the MCNP perturbation technique outperforms correlated sampling for one type of problem but performs comparably with or even under-performs correlated sampling for the other two types of problems. → In terms of accuracy, the MCNP perturbation calculations may predict inaccurate results for some of the test problems. However, the accuracy can be improved if the midpoint correction technique is used. - Abstract: Correlated sampling and the differential operator perturbation technique are two methods that enable MCNP (Monte Carlo N-Particle) to simulate small response change between an original system and a perturbed system. In this work the performance of the MCNP differential operator perturbation technique is compared with that of the MCNP correlated sampling method for three types of fixed-source problems. In terms of precision of predicted response changes, the MCNP perturbation technique outperforms correlated sampling for the problem involving variation of nuclide concentrations in the same direction but performs comparably with or even underperforms correlated sampling for the other two types of problems that involve void or variation of nuclide concentrations in opposite directions. In terms of accuracy, the MCNP differential operator perturbation calculations may predict inaccurate results that deviate from the benchmarks well beyond their uncertainty ranges for some of the test problems. However, the accuracy of the MCNP differential operator perturbation can be improved if the midpoint correction technique is used.

Dosimetric studies, spectrometric, radiographic, metallographic of a new argentinean seed of {sup 125} I used in brachytherapy; Estudios dosimetricos, espectrometricos, radiograficos, metalograficos de una nueva semilla argentina de {sup 125}I empleada en braquiterapia

Energy Technology Data Exchange (ETDEWEB)

Pirchio, R.; Saravi, M.; Banchik, D.; Munoz, C. [CNEA, Pbro. J. Gonzalez y Aragon No. 15 (B1802AYA), Ezeiza, Buenos Aires (Argentina)]. e-mail: pirchio@cae.cnea.gov.ar

2006-07-01

A new source of {sup 125} I model Braquibac{sup TM} has been developed in Argentina for applications in interstitial brachytherapy. The AAPM Task Group 43 (TG-43) recommends that dosimetric characteristics of new sources of brachytherapy of Iodine-125 have been theoretically and experimentally determined before its clinical use. The objectives outlined in this work were the study of the design of the new seed, the calculation of dosimetric parameters and the photons spectra analysis. Its were carried out radiographic and metallographic studies to determine the physical characteristics of the source. For the realization of the dosimetric calculations it was used the Monte Carlo code MCNP5. Values of the radial dose function, g(r), of the constant of dose rate, {lambda}, of the function of anisotropy of two dimensions, F(r, {theta}), of the factor and constant of anisotropy its were obtained simulating the source in water according to the recommended methodology in TG-43. The constant of dose rate is similar to 0,880 {+-} 0,080 c Gy h{sup -1} U{sup -1}. The kerma in air rate of reference, S{sub K}, was calculated as 1,036 c Gy cm{sup 2}h{sup -1} mCi{sup -1} simulating the seed in dry air. Its were carried out spectrometric studies using a semiconductor planar detector of HPGe (high purity germanium). Photons spectra showed characteristic x-rays of {sup 125} I with energies of 27,20 keV, 27,47 keV, 31 keV and 31,70 keV gamma photons of 35,5 keV, and x-ray fluorescent coming from the silver nucleus of 22,10 keV, 24,94 keV and 25,45 keV. The angular dependence of the intensity of photons around the seed and in air it was analyzed with the planar detector. This was carried out to study the anisotropy in the photons flow due to variation in the thickness of the titanium wall and of the welding, movements of the silver tube inside the source and deposition of the radioactive material on the silver tube. (Author)

Open Partial Nephrectomy in Renal Cancer: A Feasible Gold Standard Technique in All Hospitals

Directory of Open Access Journals (Sweden)

J. M. Cozar

2008-01-01

Full Text Available Introduction. Partial nephrectomy (PN is playing an increasingly important role in localized renal cell carcinoma (RCC as a true alternative to radical nephrectomy. With the greater experience and expertise of surgical teams, it has become an alternative to radical nephrectomy in young patients when the tumor diameter is 4 cm or less in almost all hospitals since cancer-specific survival outcomes are similar to those obtained with radical nephrectomy. Materials and Methods. The authors comment on their own experience and review the literature, reporting current indications and outcomes including complications. The surgical technique of open partial nephrectomy is outlined. Conclusions. Nowadays, open PN is the gold standard technique to treat small renal masses, and all nonablative techniques must pass the test of time to be compared to PN. It is not ethical for patients to undergo radical surgery just because the urologists involved do not have adequate experience with PN. Patients should be involved in the final treatment decision and, when appropriate, referred to specialized centers with experience in open or laparoscopic partial nephrectomies.

Infusing Reliability Techniques into Software Safety Analysis

Science.gov (United States)

Shi, Ying

2015-01-01

Software safety analysis for a large software intensive system is always a challenge. Software safety practitioners need to ensure that software related hazards are completely identified, controlled, and tracked. This paper discusses in detail how to incorporate the traditional reliability techniques into the entire software safety analysis process. In addition, this paper addresses how information can be effectively shared between the various practitioners involved in the software safety analyses. The author has successfully applied the approach to several aerospace applications. Examples are provided to illustrate the key steps of the proposed approach.

TEXTURE AND MECHANICAL BEHAVIOUR OF Ti AND Nb-Ti STABILIZED IF STEELS

Directory of Open Access Journals (Sweden)

Fabio Moreira da Silva Dias

2013-12-01

Full Text Available An analysis of the crystallographic texture and mechanical behavior of two types of IF steels is presented. Two steels, Ti and Nb-Ti, were submitted to different thermal annealing cycles in a continuous hot-dip galvanizing line, heat treated at temperatures of 860°C and 760°C. The more relevant characteristics of mechanical properties are evaluated. The crystallographic texture of the samples is determined by electron diffraction technique of back-scattering (SEM-EBSD. The intensity of orientation //ND is evaluated and compared. Metallographic characterization is done, and the ferritic grain size is measured with optical microscopy. The mechanical behavior of materials is characterized in the tensile test with 80 mm gauge length.

Abrasive Wear of AlSi12-Al2O3 Composite Materials Manufactured by Pressure Infiltration

Directory of Open Access Journals (Sweden)

Kremzer M.

2016-09-01

Full Text Available The aim of this study is to investigate tribological properties of EN AC-AlSi12 alloy composite materials matrix manufactured by pressure infiltration of Al2O3 porous preforms. In the paper, a technique of manufacturing composite materials was described in detail as well as wear resistance made on pin on disc was tested. Metallographic observations of wear traces of tested materials using stereoscopic and confocal microscopy were made. Studies allow concluding that obtained composite materials have much better wear resistance than the matrix alloy AlSi12. It was further proved that the developed technology of their preparation consisting of pressure infiltration of porous ceramic preforms can find a practical application.

Surface integrity and part accuracy in reaming and tapping stainless steel with new vegetable based cutting oils

DEFF Research Database (Denmark)

Belluco, Walter; De Chiffre, Leonardo

2002-01-01

This paper presents an investigation on the effect of new formulations of vegetable oils on surface integrity and part accuracy in reaming and tapping operations with AISI 316L stainless steel. Surface integrity was assessed with measurements of roughness, microhardness, and using metallographic...... as part accuracy. Cutting fluids based on vegetable oils showed comparable or better performance than mineral oils. ÆÉ2002 Published by Elsevier Science Ltd....... techniques, while part accuracy was measured on a coordinate measuring machine. A widely diffused commercial mineral oil was used as reference for all measurements. Cutting fluid was found to have a significant effect on surface integrity and thickness of the strain hardened layer in the sub-surface, as well...

Hybrid power system intelligent operation and protection involving distributed architectures and pulsed loads

Science.gov (United States)

Mohamed, Ahmed

Efficient and reliable techniques for power delivery and utilization are needed to account for the increased penetration of renewable energy sources in electric power systems. Such methods are also required for current and future demands of plug-in electric vehicles and high-power electronic loads. Distributed control and optimal power network architectures will lead to viable solutions to the energy management issue with high level of reliability and security. This dissertation is aimed at developing and verifying new techniques for distributed control by deploying DC microgrids, involving distributed renewable generation and energy storage, through the operating AC power system. To achieve the findings of this dissertation, an energy system architecture was developed involving AC and DC networks, both with distributed generations and demands. The various components of the DC microgrid were designed and built including DC-DC converters, voltage source inverters (VSI) and AC-DC rectifiers featuring novel designs developed by the candidate. New control techniques were developed and implemented to maximize the operating range of the power conditioning units used for integrating renewable energy into the DC bus. The control and operation of the DC microgrids in the hybrid AC/DC system involve intelligent energy management. Real-time energy management algorithms were developed and experimentally verified. These algorithms are based on intelligent decision-making elements along with an optimization process. This was aimed at enhancing the overall performance of the power system and mitigating the effect of heavy non-linear loads with variable intensity and duration. The developed algorithms were also used for managing the charging/discharging process of plug-in electric vehicle emulators. The protection of the proposed hybrid AC/DC power system was studied. Fault analysis and protection scheme and coordination, in addition to ideas on how to retrofit currently available

Investigation of large α production in reactions involving weakly bound 7Li

Science.gov (United States)

Pandit, S. K.; Shrivastava, A.; Mahata, K.; Parkar, V. V.; Palit, R.; Keeley, N.; Rout, P. C.; Kumar, A.; Ramachandran, K.; Bhattacharyya, S.; Nanal, V.; Palshetkar, C. S.; Nag, T. N.; Gupta, Shilpi; Biswas, S.; Saha, S.; Sethi, J.; Singh, P.; Chatterjee, A.; Kailas, S.

2017-10-01

The origin of the large α -particle production cross sections in systems involving weakly bound 7Li projectiles has been investigated by measuring the cross sections of all possible fragment-capture as well as complete fusion using the particle-γ coincidence, in-beam, and off-beam γ -ray counting techniques for the 7Li+93Nb system at near Coulomb barrier energies. Almost all of the inclusive α -particle yield has been accounted for. While the t -capture mechanism is found to be dominant (˜70 % ), compound nuclear evaporation and breakup processes contribute ˜15 % each to the inclusive α -particle production in the measured energy range. Systematic behavior of the t capture and inclusive α cross sections for reactions involving 7Li over a wide mass range is also reported.

Synthesis of nano γ-alumina by the solvothermal technique

International Nuclear Information System (INIS)

Meor Yusoff Meor Sulaiman; Masliana Muslimin

2006-01-01

The paper describes work done on synthesis of γ-alumina by using the solvo thermal technique. Synthesis of γ-alumina involves the transition reactions of the aluminium hydroxide into alumina by a dehydroxylation process. As there are many forms of transition aluminas produced during this process, a x-ray diffraction (XRD) technique was used to identify γ-alumina and the other forms of alumina. After establishing the optimum conditions for the production of a single-phase γ-alumina, characteristic study on the product was performed. An important parameter in establishing nanosized powders is their crystallite size and analysis of the γ-alumina shows that it is a nanosized powder with a size of 28 nm. Other properties analysed include morphology, surface area and particle size. (Author)

Unbiased stereologic techniques for practical use in diagnostic histopathology

DEFF Research Database (Denmark)

Sørensen, Flemming Brandt

1995-01-01

Grading of malignancy by the examination of morphologic and cytologic details in histologic sections from malignant neoplasms is based exclusively on qualitative features, associated with significant subjectivity, and thus rather poor reproducibility. The traditional way of malignancy grading may...... by introducing quantitative techniques in the histopathologic discipline of malignancy grading. Unbiased stereologic methods, especially based on measurements of nuclear three-dimensional mean size, have during the last decade proved their value in this regard. In this survey, the methods are reviewed regarding...... the basic technique involved, sampling, efficiency, and reproducibility. Various types of cancers, where stereologic grading of malignancy has been used, are reviewed and discussed with regard to the development of a new objective and reproducible basis for carrying out prognosis-related malignancy grading...

Constructing canine carotid artery stenosis model by endovascular technique

International Nuclear Information System (INIS)

Cheng Guangsen; Liu Yizhi

2005-01-01

Objective: To establish a carotid artery stenosis model by endovascular technique suitable for neuro-interventional therapy. Methods: Twelve dogs were anesthetized, the unilateral segments of the carotid arteries' tunica media and intima were damaged by a corneous guiding wire of home made. Twenty-four carotid artery stenosis models were thus created. DSA examination was performed on postprocedural weeks 2, 4, 8, 10 to estimate the changes of those stenotic carotid arteries. Results: Twenty-four carotid artery stenosis models were successfully created in twelve dogs. Conclusions: Canine carotid artery stenosis models can be created with the endovascular method having variation of pathologic characters and hemodynamic changes similar to human being. It is useful for further research involving the new technique and new material for interventional treatment. (authors)

Organizing for public involvement in Fernald decision-making

International Nuclear Information System (INIS)

Morgan, K.L.; Hoopes, J.

1993-01-01

Fernald is returning to the basics of interpersonal communication as a cornerstone of its public involvement program. The guiding premise behind this concept is the belief that face-to-face interaction between people is more likely to build trust and confidence than public meetings, news releases and other traditional public information techniques. A network of project spokespersons, called ''envoys,'' is being organized to develop person-to-person relationships with people interested in the future of Fernald. To support this approach, public affairs personnel are adopting roles as management consultants and communications coaches in addition to serving in their traditional role as public information specialists. Early observations seem to show signs of improvement in the level of public trust in Fernald decision-makers

Organizing for public involvement in Fernald decision-making

Energy Technology Data Exchange (ETDEWEB)

Morgan, K.L. [USDOE Fernald Field Office, OH (United States); Hoopes, J. [Fernald Environmental Restoration Management Corp., Cincinnati, OH (United States). Fernald Environmental Management Project

1993-10-24

Fernald is returning to the basics of interpersonal communication as a cornerstone of its public involvement program. The guiding premise behind this concept is the belief that face-to-face interaction between people is more likely to build trust and confidence than public meetings, news releases and other traditional public information techniques. A network of project spokespersons, called ``envoys,`` is being organized to develop person-to-person relationships with people interested in the future of Fernald. To support this approach, public affairs personnel are adopting roles as management consultants and communications coaches in addition to serving in their traditional role as public information specialists. Early observations seem to show signs of improvement in the level of public trust in Fernald decision-makers.

Double-lock technique: a simple method to secure abdominal wall closure

International Nuclear Information System (INIS)

Jategaonkar, P.A.; Yadav, S.P.

2013-01-01

Secure closure of a laparotomy incision remains an important aspect of any abdominal operation with the aim to avoid the postoperative morbidity and hasten the patient's recovery. Depending on the operator's preference and experience, it may be done by the continuous or the interrupted methods either using a non-absorbable or delayed-absorbable suture. We describe a simple, secure and quick technique of abdominal wall closure which involves continuous suture inter-locked doubly after every third bite. This simple and easy to use mass closure technique can be easily mastered by any member of the surgical team and does not need any assistant. It amalgamates the advantages of both, the continuous and the interrupted methods of closures. To our knowledge, such a technique has not been reported in the literature. (author)

Features improvement techniques supply of highly skilled bodybuilders in transition training

Directory of Open Access Journals (Sweden)

Oleksandr Aghyppo

2015-03-01

Full Text Available Purpose of this paper is to improve the supply of highly skilled technique bodybuilders training in a transition period with the restoration of lean body mass and functional state of an athlete after a competitive activity. Material and Method: the study involved 18 highly skilled bodybuilders are included in the team of the Kharkiv region of Ukraine and bodybuilding. Results: a comparative characteristic of the conventional technique that is often used in the training process in bodybuilding. Developed and justified the optimal technique for highly skilled bodybuilders, depending on the initial form of the athlete at the beginning of the transition period of training. Conclusions: on the basis of the study the author suggests best practices in supply depending on the microcycle training in transition training.

Stopped-flow technique for transit time measurement in a gas jet

International Nuclear Information System (INIS)

Rengan, K.; Lin, J.; Lim, T.; Meyer, R.A.; Harrell, J.

1985-01-01

A 'stopped-flow' technique for the measurement of transit time of reaction products in a gas jet is described. The method involved establishing the gas flow through the jet system when the reactor is operating steadily and allowing the pressure to reach equilibrium values. The gas flow is stopped by means of electrically operated valves. The transit-time measurement is achieved by opening the valves and initiating the multiscanning of total activity simultaneously. The value obtained agrees well with the transit time measured by pulsing the reactor. The 'stopped-flow' technique allows on-line measurement of transit time in any gas jet system where the physical transportation time is the major component of the transit time. This technique is especially useful for systems installed in reactors which do not have pulsing capability. (orig.)

Safeguards techniques and equipment. 2003 ed

International Nuclear Information System (INIS)

2003-01-01

The 1990s saw significant non-proliferation related developments in the world, resulting in a new period of safeguards development. Over several years an assessment was made of how to strengthen the effectiveness and improve the efficiency of IAEA safeguards. In May 1997 this culminated in the adoption by the IAEA Board of Governors of a Protocol Additional to Safeguards Agreements which significantly broadens the role of IAEA safeguards. As a consequence, the IAEA safeguards system entered a new era. In 1997 the IAEA began to publish a new series of booklets on safeguards, called the International Nuclear Verification Series (NVS). The objective of these booklets was to help in explaining IAEA safeguards, especially the new developments in safeguards, particularly for facility operators and government officers involved with these topics. The current booklet, which is a revision and update of IAEA/NVS/1, is intended to give a full and balanced description of the techniques and equipment used for both nuclear material accountancy and containment and surveillance measures, and for the new safeguards measure of environmental sampling. A completely new section on data security has been added to describe the specific features that are included in installed equipment systems in order to ensure the authenticity and confidentiality of information. As new verification measures continue to be developed the material in this booklet will be periodically reviewed and updated versions issued. The basic verification measure used by the IAEA is nuclear material accountancy. In applying nuclear material accountancy, IAEA safeguards inspectors make independent measurements to verify quantitatively the amount of nuclear material presented in the State's accounts. For this purpose, inspectors count items (e.g. fuel assemblies, bundles or rods, or containers of powdered compounds of uranium or plutonium) and measure attributes of these items during their inspections using non

Radiologically detectable musculoskeletal involvement in systemic lupus erythematosus

International Nuclear Information System (INIS)

Jimenez, M. M.; Manjon, P.; Diaz de Bustamante, T.; Galindo, M.; Buj, M. J.; Cabezudo, J.

2000-01-01

We show a wide spectrum of musculoskeletal involvement in systemic lupus erythematosus (SLE) that can be detected by radiological examination. We determined the indications of different imaging techniques in the diagnosis and follow-up of this disease. We reviewed the clinical and radiological histories of 37 patients diagnosed as having SLE on the basis of serological and musculoskeletal criteria. We assessed the personal data of each patient, the association of the disease with autoimmune processes, serology, treatment and radiological findings using plain X ray, ultrasound, computed tomography (CT) and magnetic resonance (MR). Of the 37 cases reviewed, only ten presented changes in one or more of the imaging studies performed. the most common radiological finding was symmetric poly arthritis located at different sites. Other signs included avascular necrosis (late and early), inflammation and tendon and/or ligament rupture, nonerosive deforming arthropathies , soft tissue calcifications and arthritis (staphylococcal and tuberculous). A direct correlation was established between the anticardiolipin antibody titer, steroid doses and avascular necrosis. In SLE, radiologically detectable osteoarticular lesions are uncommon. Symmetric polyarthritis is the earliest lesion and that occurring most frequently. Other signs do not appear as often, with the exception of osteonecrosis, which usually occurs late. It developed early and was unusually aggressive in two youths with elevated anticardiolipin antibody titers and substantial systemic involvement in our series. The contributions of ultrasound and MR in the assessment of musculoskeletal involvement in SLE are especially relevant in the study of inflammations and tendon rupture and in the management of avascular necrosis, respectively. (Author) 17 refs

The development of an audit technique to assess the quality of safety barrier management

International Nuclear Information System (INIS)

Guldenmund, Frank; Hale, Andrew; Goossens, Louis; Betten, Jeroen; Duijm, Nijs Jan

2006-01-01

This paper describes the development of a management model to control barriers devised to prevent major hazard scenarios. Additionally, an audit technique is explained that assesses the quality of such a management system. The final purpose of the audit technique is to quantify those aspects of the management system that have a direct impact on the reliability and effectiveness of the barriers and, hence, the probability of the scenarios involved. First, an outline of the management model is given and its elements are explained. Then, the development of the audit technique is described. Because the audit technique uses actual major hazard scenarios and barriers within these as its focus, the technique achieves a concreteness and clarity that many other techniques often lack. However, this strength is also its limitation, since the full safety management system is not covered with the technique. Finally, some preliminary experiences obtained from several test sites are compiled and discussed

The development of an audit technique to assess the quality of safety barrier management

Energy Technology Data Exchange (ETDEWEB)

Guldenmund, Frank [Safety Science Group, Delft University of Technology (Netherlands)]. E-mail: f.w.guldenmund@tbm.tudelft.nl; Hale, Andrew [Safety Science Group, Delft University of Technology (Netherlands); Goossens, Louis [Safety Science Group, Delft University of Technology (Netherlands); Betten, Jeroen [Safety Science Group, Delft University of Technology (Netherlands); Duijm, Nijs Jan [Riso National Laboratory (Denmark)

2006-03-31

This paper describes the development of a management model to control barriers devised to prevent major hazard scenarios. Additionally, an audit technique is explained that assesses the quality of such a management system. The final purpose of the audit technique is to quantify those aspects of the management system that have a direct impact on the reliability and effectiveness of the barriers and, hence, the probability of the scenarios involved. First, an outline of the management model is given and its elements are explained. Then, the development of the audit technique is described. Because the audit technique uses actual major hazard scenarios and barriers within these as its focus, the technique achieves a concreteness and clarity that many other techniques often lack. However, this strength is also its limitation, since the full safety management system is not covered with the technique. Finally, some preliminary experiences obtained from several test sites are compiled and discussed.

Improving skill development: an exploratory study comparing a philosophical and an applied ethical analysis technique

Science.gov (United States)

Al-Saggaf, Yeslam; Burmeister, Oliver K.

2012-09-01

This exploratory study compares and contrasts two types of critical thinking techniques; one is a philosophical and the other an applied ethical analysis technique. The two techniques analyse an ethically challenging situation involving ICT that a recent media article raised to demonstrate their ability to develop the ethical analysis skills of ICT students and professionals. In particular the skill development focused on includes: being able to recognise ethical challenges and formulate coherent responses; distancing oneself from subjective judgements; developing ethical literacy; identifying stakeholders; and communicating ethical decisions made, to name a few.

Behavior change techniques in top-ranked mobile apps for physical activity.

Science.gov (United States)

Conroy, David E; Yang, Chih-Hsiang; Maher, Jaclyn P

2014-06-01

Mobile applications (apps) have potential for helping people increase their physical activity, but little is known about the behavior change techniques marketed in these apps. The aim of this study was to characterize the behavior change techniques represented in online descriptions of top-ranked apps for physical activity. Top-ranked apps (n=167) were identified on August 28, 2013, and coded using the Coventry, Aberdeen and London-Revised (CALO-RE) taxonomy of behavior change techniques during the following month. Analyses were conducted during 2013. Most descriptions of apps incorporated fewer than four behavior change techniques. The most common techniques involved providing instruction on how to perform exercises, modeling how to perform exercises, providing feedback on performance, goal-setting for physical activity, and planning social support/change. A latent class analysis revealed the existence of two types of apps, educational and motivational, based on their configurations of behavior change techniques. Behavior change techniques are not widely marketed in contemporary physical activity apps. Based on the available descriptions and functions of the observed techniques in contemporary health behavior theories, people may need multiple apps to initiate and maintain behavior change. This audit provides a starting point for scientists, developers, clinicians, and consumers to evaluate and enhance apps in this market. Copyright © 2014 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Comments on the equilibrium diagram of the Ti-Zr system

International Nuclear Information System (INIS)

Ruch, M.; Arias, D.

1993-01-01

The Ti-Zr system is a continuous series of solid solutions in both the α- and β-phases, with a congruent minimum at Ti-50at%Zr. The equilibrium diagram has been reviewed by Murray in 1981, who accepts the α/β temperature for this minimum determined by Farrar and Adler by metallographic techniques. Etchessahar and Debuigne measured by dilatometry a transformation temperature of (894 ±)K and (859±2)K for α/α + β and β/α + β respectively, and later in a high temperature Calvet microcalorimeter, 883K. Blacktop et al find that this value is consistent with their measurements of the α/β transformation temperature in Ti-40%Zr and Ti-60%Zr in a high temperature calorimeter. In the present work, the α/β transformation temperature was measured by several techniques. The effect of impurities is considered in both transformation temperature and microstructure of product phases

A study on the manufacturing and processing technologies of DUPIC fuel

International Nuclear Information System (INIS)

Yang, Myung Seung; Park, J.J.; Lee, J.W.; Kim, S.S.; Yim, S.P.; Kim, J.H.; Kim, K.H.; Na, S.H.; Kim, W.K.; Kang, K.H.; Shin, J.M.; Lee, D.Y.; Cho, K.H.; Lee, Y.S.; Sohn, J.S.; Kim, M.J.

1999-06-01

In this study, DUPIC fuel fabrication technologies are developed, characteristics of fuel materials are studied, and characterization experiments for DUPIC powder and pellets are performed at PIEF. SIMFUEL powder and pellets are made of UO 2 mixed with the simulated fission products of spent fuel. Both characteristics of SIMFUEL powder and micro-structure of pellets are analyzed. End cap of DUPIC fuel rod is sealed with laser welding technique. Optimum welding condition is analyzed with results of Micro-hardness, mechanical and metallographic tests. Micro-focus x-ray inspection technique is studied to fine fine defects. DUPIC processes are improved by making OREOX process be multi-functional and by adopting rol compacting process. At PIEF, characterization experiments for DUPIC powder and pellet are performed. The equipment for experiments have been installed at PIEF no. 9405 hot cell, and its process parameters are established. (author). 7 refs., 7 tabs., 37 figs

Plate Fixation With Autogenous Calcaneal Dowel Grafting Proximal Fourth and Fifth Metatarsal Fractures: Technique and Case Series.

Science.gov (United States)

Seidenstricker, Chad L; Blahous, Edward G; Bouché, Richard T; Saxena, Amol

Metaphyseal and proximal diaphyseal fractures of the lateral column metatarsals can have problems with healing. In particular, those involving the fifth metatarsal have been associated with a high nonunion rate with nonoperative treatment. Although intramedullary screw fixation results in a high union rate, delayed healing and complications can occur. We describe an innovative technique to treat both acute and chronic injuries involving the metatarsal base from the metaphysis to the proximal diaphyseal bone of the fourth and fifth metatarsals. The surgical technique involves evacuation of sclerotic bone at the fracture site, packing the fracture site with compact cancellous bone, and plate fixation. In our preliminary results, 4 patients displayed 100% radiographic union at a mean of 4.75 (range 4 to 6) weeks with no incidence of refracture, at a mean follow-up point of 3.5 (range 1 to 5) years. The early results with our small series suggest that this technique is a useful treatment choice for metaphyseal and proximal diaphyseal fractures of the fourth and fifth metatarsals. Copyright © 2017 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Nonlinear radiation transport problems involving widely varying mean free paths

International Nuclear Information System (INIS)

Chapline, G. Jr.; Wood, L.

1976-01-01

In this report a method is given for modifying the Monte-Carlo approach so that one can accurately treat problems that involve both large and small mean free paths. This method purports to offer the advantages of the general Monte Carlo technique as far as relatively great accuracy of simulation of microscopic physical phenomena is concerned, and the advantage of a diffusion theory approach as far as decent time steps in thick problems are concerned; it does suffer from something of the statistical fluctuation problems of the Monte Carlo, although in analytically attenuated and modified form

Swarm Intelligence: New Techniques for Adaptive Systems to Provide Learning Support

Science.gov (United States)

Wong, Lung-Hsiang; Looi, Chee-Kit

2012-01-01

The notion of a system adapting itself to provide support for learning has always been an important issue of research for technology-enabled learning. One approach to provide adaptivity is to use social navigation approaches and techniques which involve analysing data of what was previously selected by a cluster of users or what worked for…

Measurement of fracture toughness of metallic materials produced by additive manufacturing

Science.gov (United States)

Quénard, O.; Dorival, O.; Guy, Ph.; Votié, A.; Brethome, K.

2018-04-01

This study focuses on the microstructure and mechanical properties of metallic materials produced by additive layer manufacturing (ALM), especially the laser beam melting process. The influence of the specimen orientation during the ALM process and that of two post-build thermal treatments were investigated. The identified metal powder is Ti-6Al-4V (titanium base). Metallographic analysis shows their effects on the microstructure of the metals. Mechanical experiments involving tensile tests as well as toughness tests were performed according to ASTM (American Society for Testing and Materials) norms. The results show that the main influence is that of the thermal treatments; however the manufacturing stacking direction may lead to some anisotropy in the mechanical properties.

Failure investigations in the nuclear materials laboratory

International Nuclear Information System (INIS)

Woitscheck, A.

1982-01-01

A report is given of damage to hydrostatic floating seals (with a single-stage pressure drop of 155 bar) from pressurized water reactors. The seals were manufactured from the steel X 22 CrNi 17 and plasmacoated with a layer of Cr 2 O 3 . The types of damage occurring (green discoloration and hump formation) are discussed in terms of their mechanistic causes. A further investigation involved metallographic examination with optical and scanning electron microscopes of seven specimens from thin-walled piping made of the finegrained, structural steel 17 MnMoV 6,4 in which cracking had occurred in weld regions, in particular, crack growth and the form of cracking at the weld root were investigated. (orig.) [de

LASER WELDING WITH MICRO-JET COOLING FOR TRUCK FRAME WELDING

Directory of Open Access Journals (Sweden)

Jan PIWNIK

2017-12-01

Full Text Available The aim of this paper is to analyse the mechanical properties of the weld steel structure of car body truck frames after laser welding. The best welding conditions involve the use of proper materials and alloy elements in steel and filer materials, in addition to welding technology, state of stress and temperature of exploitation. We present for the first time the properties of steel track structures after laser welding with micro-jet cooling. Therefore, good selection of both welding parameters and micro-jet cooling parameters is very important to achieve a proper steel structure. In this study, the metallographic structure, tensile results and impact toughness of welded joints have been analysed in terms of welding parameters.

Clinical evaluation of myocardial involvement in acute myopericarditis in young adults.

Science.gov (United States)

Saricam, Ersin; Saglam, Yasemin; Hazirolan, Tuncay

2017-05-22

Myocardial involvement in young adults has various causes. Acute myopericarditis is one of the myocardial involvements in young adults. It is easy to confuse with acute ST-elevation myocardial infarction because of the electrocardiographic features. This study aims to investigate a number of imaging techniques and clinical features for acute myopericarditis in young adults (defined as myocardial brightness in the left ventricle regions, especially in posterior and lateral wall. Focal echobright was observed in the 75 of 77 cases of acute myopericarditis in transthoracic echocardiogram. This sign was confirmed by cardiac magnetic resonance imaging. Focal echobright sensitivity was 95%; its specificity was 93%; its predictive was 95.2%. Pericardial effusion (83%) was observed in group I behind posterior wall. Its specificity was 81%; its sensitivity was 65%; predictivity was 73%. Pericardial effusion and myocardial focal echobright in echocardiography can be quite sensitive indicators for acute myopericarditis in young adults.

The study of trace elements in milk by nuclear analytical techniques

International Nuclear Information System (INIS)

Gharib, A.; Rahimi, H.; Peyrovan, H.; Raofei, H.N.J.; Taherpour, H.

1983-01-01

This work is part of a project with the IAEA, in a coordinated programme on ''Trace Elements in Human Nutrition and Bio-Environmental Systems'' to evaluate their nutritional requirements, interrelations and the role of Trace Elements in health, metabolism etc. Cow's milk being regarded as one of the most important and nutritious foodstuffs consumed by people. Hence as a first step, an elemental analysis for milk was carried out for this purpose so a few samples of pasteurized milk and local samples were investigated for essential and toxic trace elements. The secondary aim of this project was the assessment of various analytical techniques involved. However, in the present work, the methods involved were AAS, PIXE and NAA. The latter method applied, both instrumentally and radiochemically. Although the results pertaining to the various methods employed are not in good agreement, there is however, some justification to clarify this internal inconsistency. The precision for NAA and AAS allows greater degree of acceptance respectively. Although PIXE is a very fast and rather a routine but the technique of trace element analysis needs certain adaptations and developments

Evaluation of brachial plexus fascicles involvement on infraclavicular block: unfixed cadaver study

Directory of Open Access Journals (Sweden)

Luiz Carlos Buarque de Gusmão

2015-06-01

Full Text Available BACKGROUND AND OBJECTIVES: This study shows how the diffusion of the anesthetic into the sheath occurs through the axillary infraclavicular space and hence proves the efficacy of the anesthetic block of the brachial plexus, and may thereby allow a consolidation of this pathway, with fewer complications, previously attached to the anesthesia. MATERIALS AND METHODS: 33 armpits of adult cadavers were analyzed and unfixed. We injected a solution of neoprene with latex dye in the infraclavicular space, based on the technique advocated by Gusmão et al., and put the corpses in refrigerators for three weeks. Subsequently, the specimens were thawed and dissected, exposing the axillary sheath along its entire length. RESULTS AND DISCUSSION: Was demonstrated involvement of all fasciculus of the plexus in 51.46%. In partial involvement was 30.30%, 18.24% of cases the acrylic was located outside the auxiliary sheath involving no issue. CONCLUSIONS: The results allow us to establish the infraclavicular as an effective and easy way to access plexus brachial, because the solution involved the fascicles in 81.76% partially or totally, when it was injected inside the axillary sheath. We believe that only the use of this pathway access in practice it may demonstrate the efficiency.

Comparison of denture tooth movement between CAD-CAM and conventional fabrication techniques.

Science.gov (United States)

Goodacre, Brian J; Goodacre, Charles J; Baba, Nadim Z; Kattadiyil, Mathew T

2018-01-01

-CAM-bonded, injection, and fluid resin. Techniques involving compression during processing showed increased positive occlusal tooth movement compared with techniques not involving compression. CAD-CAM monolithic dentures produced the best combination of accuracy and reproducibility of the tested techniques. The results from this study demonstrate that varying amounts of tooth movement can be expected depending on the processing technique. However, the clinical significance of these differences is unknown. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Drug abuse in the workplace: employee screening techniques

International Nuclear Information System (INIS)

Buzzeo, R.W.

1984-01-01

Recent studies show that as many as three to five percent of the employees of a medium- to large-sized plant may be dependent on drugs as a way of life. The detrimental effects of drug abuse in the workplace can be measured in lost productivity, poor quality control and other areas at an annual cost to the American economy of $30 billion. However, a price tag cannot be attached to the lives affected by this unrelenting problem. The purpose of this paper is to provide an overview of the employee screening and hiring techniques available to industry to detect and eliminate potentially dangerous or fatal situations involving drug abuse in the workplace. The techniques are universal and can be effectively applied by the nuclear industry as well as other businesses to ensure that its work force is a reputable and reliable one

Model order reduction techniques with applications in finite element analysis

CERN Document Server

Qu, Zu-Qing

2004-01-01

Despite the continued rapid advance in computing speed and memory the increase in the complexity of models used by engineers persists in outpacing them. Even where there is access to the latest hardware, simulations are often extremely computationally intensive and time-consuming when full-blown models are under consideration. The need to reduce the computational cost involved when dealing with high-order/many-degree-of-freedom models can be offset by adroit computation. In this light, model-reduction methods have become a major goal of simulation and modeling research. Model reduction can also ameliorate problems in the correlation of widely used finite-element analyses and test analysis models produced by excessive system complexity. Model Order Reduction Techniques explains and compares such methods focusing mainly on recent work in dynamic condensation techniques: - Compares the effectiveness of static, exact, dynamic, SEREP and iterative-dynamic condensation techniques in producing valid reduced-order mo...

Cell-Detection Technique for Automated Patch Clamping

Science.gov (United States)

McDowell, Mark; Gray, Elizabeth

2008-01-01

A unique and customizable machinevision and image-data-processing technique has been developed for use in automated identification of cells that are optimal for patch clamping. [Patch clamping (in which patch electrodes are pressed against cell membranes) is an electrophysiological technique widely applied for the study of ion channels, and of membrane proteins that regulate the flow of ions across the membranes. Patch clamping is used in many biological research fields such as neurobiology, pharmacology, and molecular biology.] While there exist several hardware techniques for automated patch clamping of cells, very few of those techniques incorporate machine vision for locating cells that are ideal subjects for patch clamping. In contrast, the present technique is embodied in a machine-vision algorithm that, in practical application, enables the user to identify good and bad cells for patch clamping in an image captured by a charge-coupled-device (CCD) camera attached to a microscope, within a processing time of one second. Hence, the present technique can save time, thereby increasing efficiency and reducing cost. The present technique involves the utilization of cell-feature metrics to accurately make decisions on the degree to which individual cells are "good" or "bad" candidates for patch clamping. These metrics include position coordinates (x,y) in the image plane, major-axis length, minor-axis length, area, elongation, roundness, smoothness, angle of orientation, and degree of inclusion in the field of view. The present technique does not require any special hardware beyond commercially available, off-the-shelf patch-clamping hardware: A standard patchclamping microscope system with an attached CCD camera, a personal computer with an imagedata- processing board, and some experience in utilizing imagedata- processing software are all that are needed. A cell image is first captured by the microscope CCD camera and image-data-processing board, then the image

Active load control techniques for wind turbines.

Energy Technology Data Exchange (ETDEWEB)

van Dam, C.P. (University of California, Davis, CA); Berg, Dale E.; Johnson, Scott J. (University of California, Davis, CA)

2008-07-01

This report provides an overview on the current state of wind turbine control and introduces a number of active techniques that could be potentially used for control of wind turbine blades. The focus is on research regarding active flow control (AFC) as it applies to wind turbine performance and loads. The techniques and concepts described here are often described as 'smart structures' or 'smart rotor control'. This field is rapidly growing and there are numerous concepts currently being investigated around the world; some concepts already are focused on the wind energy industry and others are intended for use in other fields, but have the potential for wind turbine control. An AFC system can be broken into three categories: controls and sensors, actuators and devices, and the flow phenomena. This report focuses on the research involved with the actuators and devices and the generated flow phenomena caused by each device.

E12 sheet plastination: Techniques and applications.

Science.gov (United States)

Ottone, Nicolas Ernesto; Baptista, Carlos A C; Latorre, Rafael; Bianchi, Homero Felipe; Del Sol, Mariano; Fuentes, Ramon

2017-10-30

Plastination is an anatomical technique that consists of replacing the liquids and fat of specimens by reactive polymers through forced impregnation in a vacuum. These are then polymerized to achieve the final result. E12 sheet plastination involves epoxy resin impregnation of thin (2-4 mm) and ultra-thin (SciELO databases, and manual searches. After searching, 616 records were found using the online and manual searches (MEDLINE, n: 207; EMBASE, n: 346; SciELO, n: 44; Manual search: 23). Finally, 96 records were included in this review (after duplicates and articles unrelated to the subject were excluded). The aim of this work was to review the E12 sheet plastination technique, searching for articles concerning views of it, identifying the different variants implemented by researchers since its creation by Gunther von Hagens, and to identify its applications from teaching and research in anatomy to morphological sciences. Clin. Anat., 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Using project management techniques in hydro-relicensing

International Nuclear Information System (INIS)

Dominie, D.; Richard, J.

1991-01-01

This paper reports that to answer a pressing need for managing today's complex process and requirements of hydro relicensing, Central Maine Power Company has applied the principles of project management, including the use of computerized scheduling to its hydro relicensing efforts. This approach involves early inter-departmental cooperation in mapping out critical path scheduling by requiring the project team to: Outline the scope of the project in its entirety. Clarify and define components of the project. Quantify and categorize assumptions and dependencies. Identify constraints. The computer-generated schedule of this cooperative planning effort provides a graphic representation of the team's plan and become the focal point for refinements and adjustments necessary to complete an application on time. The use of project management techniques facilities team understanding of the realities and limitations in the relicensing process. These techniques encourage cooperative action, and use a solution-oriented process resulting in a product which can be a useful tool in communicating with resource agencies and regulators

Study of trace elements in milk by nuclear analytical techniques

Energy Technology Data Exchange (ETDEWEB)

Gharib, A.; Rahimi, H.; Peyrovan, H.; Raofei, H.N.J.; Taherpour, H. (Atomic Energy Organization of Iran, Teheran. Nuclear Research Centre)

This work is part of a project with the IAEA, in a coordinated programme on ''trace elements in Human Nutrition and Bio-Environmental Systems'' to evaluate their nutritional requirements, interrelations and the role of trace elements in health, metabolism etc. Cow's milk is regarded as one of the most important and nutritious foodstuffs consumed by people. Hence, as a first step, an elemental analysis for milk was carried out for this purpose so a few samples of pasteurized milk and local samples were investigated for essential and toxic trace elements. The secondary aim of this project was the assessment of various analytical techniques involved. However, in the present work, the methods involved were AAS, PIXE and NAA. The latter method applied, both instrumentally and radiochemically. Although the results pertaining to the various methods employed are not in good agreement, there is however, some justification to clarify this internal inconsistency. The precision for NAA and AAS allows greater degree of acceptance respectively. Although PIXE is very fast and rather routine, the technique of trace element analysis needs certain adaptations and developments.

Diagnosis of myocardial involvement in patients with systemic myopathies with 15-(p-[I-123]iodophenyl) pentadecanoic acid (IPPA) SPECT

Energy Technology Data Exchange (ETDEWEB)

Kropp, J.; Briele, B.; Smekal, A.V.; Hotze, A.L.; Biersack, H.J.; Koehler, U.; Zierz, St. [Bonn Univ. (Germany); Knapp, F.F. [Oak Ridge National Lab., TN (United States)

1992-03-01

Involvement of the myocardium in non-infectious myopathies presents in most cases as systolic dysfunction or a disturbed cardiac rhythm. We are interested in exploring how often cardiac involvement can be evaluated with various diagnostic techniques in patients with proven myopathy. We investigated 41 patients with myopathies of various etiology, including mitochondrial and congenital myopathies, Curshmann-Steinert disease, muscular dystrophy, and others. Myopathy was proven by muscular biopsy usually from the bicep. Fatty acid imaging was performed with 15-(p-[I-123]iodophenyl)pentadecanoic acid (IP-PA) and sequential SPECT-scintigraphy with a 180 deg. rotation starting at the 45 deg. RAO position. 190 MBq were injected at the maximal stage of a submaximal exercise. Filtered backprojection and reorientation of the slices were achieved by standard techniques. The quantitative comparison of the oblique slices (bulls-eye technique) of the SPECT-studies revealed turnover-rates as a qualitative measure of {beta}-oxidation. Serum levels of lactate (L), pyruvate (P), glucose (G) and triglycerides (TG) were measured at rest and stress. Ventricular function was investigated by radionuclide ventriculography (MUGA) at rest and under stress with Tc-99m labeled red blood cells. In addition, ECG, 24 hour-ECG, and echocardiography were also performed with standard techniques.

Diagnosis of myocardial involvement in patients with systemic myopathies with 15-(p-(I-123)iodophenyl) pentadecanoic acid (IPPA) SPECT

Energy Technology Data Exchange (ETDEWEB)

Kropp, J.; Briele, B.; Smekal, A.V.; Hotze, A.L.; Biersack, H.J.; Koehler, U.; Zierz, St. (Bonn Univ. (Germany)); Knapp, F.F. (Oak Ridge National Lab., TN (United States))

1992-01-01

Involvement of the myocardium in non-infectious myopathies presents in most cases as systolic dysfunction or a disturbed cardiac rhythm. We are interested in exploring how often cardiac involvement can be evaluated with various diagnostic techniques in patients with proven myopathy. We investigated 41 patients with myopathies of various etiology, including mitochondrial and congenital myopathies, Curshmann-Steinert disease, muscular dystrophy, and others. Myopathy was proven by muscular biopsy usually from the bicep. Fatty acid imaging was performed with 15-(p-(I-123)iodophenyl)pentadecanoic acid (IP-PA) and sequential SPECT-scintigraphy with a 180 deg. rotation starting at the 45 deg. RAO position. 190 MBq were injected at the maximal stage of a submaximal exercise. Filtered backprojection and reorientation of the slices were achieved by standard techniques. The quantitative comparison of the oblique slices (bulls-eye technique) of the SPECT-studies revealed turnover-rates as a qualitative measure of {beta}-oxidation. Serum levels of lactate (L), pyruvate (P), glucose (G) and triglycerides (TG) were measured at rest and stress. Ventricular function was investigated by radionuclide ventriculography (MUGA) at rest and under stress with Tc-99m labeled red blood cells. In addition, ECG, 24 hour-ECG, and echocardiography were also performed with standard techniques.

Diagnosis of myocardial involvement in patients with systemic myopathies with 15-(p-[I-123]iodophenyl) pentadecanoic acid (IPPA) SPECT

International Nuclear Information System (INIS)

Kropp, J.; Briele, B.; Smekal, A.V.; Hotze, A.L.; Biersack, H.J.; Koehler, U.; Zierz, St.; Knapp, F.F.

1992-01-01

Involvement of the myocardium in non-infectious myopathies presents in most cases as systolic dysfunction or a disturbed cardiac rhythm. We are interested in exploring how often cardiac involvement can be evaluated with various diagnostic techniques in patients with proven myopathy. We investigated 41 patients with myopathies of various etiology, including mitochondrial and congenital myopathies, Curshmann-Steinert disease, muscular dystrophy, and others. Myopathy was proven by muscular biopsy usually from the bicep. Fatty acid imaging was performed with 15-(p-[I-123]iodophenyl)pentadecanoic acid (IP-PA) and sequential SPECT-scintigraphy with a 180 deg. rotation starting at the 45 deg. RAO position. 190 MBq were injected at the maximal stage of a submaximal exercise. Filtered backprojection and reorientation of the slices were achieved by standard techniques. The quantitative comparison of the oblique slices (bulls-eye technique) of the SPECT-studies revealed turnover-rates as a qualitative measure of β-oxidation. Serum levels of lactate (L), pyruvate (P), glucose (G) and triglycerides (TG) were measured at rest and stress. Ventricular function was investigated by radionuclide ventriculography (MUGA) at rest and under stress with Tc-99m labeled red blood cells. In addition, ECG, 24 hour-ECG, and echocardiography were also performed with standard techniques

Re-utilization by '' Stud Welding'' of capsules charpy-V belonged to surveillance programs

International Nuclear Information System (INIS)

Lapena, J.; Perosanz, F. J.; Gachuz, M.

1998-01-01

The perspectives of nuclear plants life extension that are approximating to their end of design life compels to make new surveillance programs. The re-utilization of specimens belonging to surveillance capsules already tested in these new surveillance programs seems be a solution worldwide accepted. The two possible re-utilization processes of this irradiated material are: Subsized specimens and Reconstitution. While the first alternative (Subsized specimens) outlines serious problems for apply the results, the reconstitution eliminates this problem, since the resulting specimens after of the reconstruction procedure would be of the same dimensions that the original. The reconstruction process involves welds, and therefore it has associated the specific problems of this type of joints. Furthermore, by be tried to material irradiated with certain degree of internal damage, that is the variable to evaluate, requires that the heat contribution to the piece not originate local thermal treatments that alter its mechanical qualities. In this work has been followed the evolution by the variables of the weld process and their influence on the quality by the union from metallographic al point of view as well as mechanical for a weld procedure by Stud Welding. The principal objective is to optimize said parameters to assure a good mechanical continuity, without detriment of the microstructural characteristics of the original material. To verify this last have been accomplished with metallographical tests, temperature profile, hardness and will be carried out also Charpy tests. (Author)

[Training program design of acupuncture and moxibustion manipulation techniques].

Science.gov (United States)

Dong, Qin

2009-12-01

As an important component of acupuncture-moxibustion science, needling and moxibustion is one methodology and technology and its technical characteristics determine its special status and role in training programs. It is closely ralated to meridians-collaterals-acupoints and acupuncture treatment. Therefore, it demands an overall planning for acupuncture professional skills that consists of meridians-collaterals-acupoints knowledge and acupuncture treatment techniques. The practical training courses are the step by step progress involving repeated practices.

Aquifer restoration techniques for in-situ leach uranium mines

International Nuclear Information System (INIS)

Deutsch, W.J.; Bell, N.E.; Mercer, B.W.; Serne, R.J.; Shade, J.W.; Tweeton, D.R.

1984-02-01

In-situ leach uranium mines and pilot-scale test facilities are currently operating in the states of Wyoming, Texas, New Mexico and Colorado. This report summarizes the technical considerations involved in restoring a leached ore zone and its aquifer to the required level. Background information is provided on the geology and geochemistry of mineralized roll-front deposits and on the leaching techniques used to extract the uranium. 13 references, 13 figures, 4 tables

Technique for preparation of transmission electron microscope specimens from wire samples of Al and Al-Al2O3 alloys

DEFF Research Database (Denmark)

Lindbo, Jørgen

1966-01-01

A technique for thinning 1 mm wire samples of aluminium and aluminium-alumina alloys for transmission electron microscopy is described. The essential feature of the technique, which involves spark machining and electropolishing in a polytetrafluoroethylene holder followed by chemical polishing...

Monotectic four-phase reaction in Al-Bi-Zn alloys

Energy Technology Data Exchange (ETDEWEB)

Groebner, J. [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany); Mirkovic, D. [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany); Schmid-Fetzer, R. [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany)]. E-mail: schmid-fetzer@tu-clausthal.de

2005-06-15

Thermodynamic phase diagram calculations were used for the systematic search for a monotectic four-phase reaction in ternary Al-alloys. Systems with intermetallic phases and also the elements Cd and Hg were excluded in the present search. The ternary Al-Bi-Zn is a rare occasion where such a reaction, L' = L' + (Al)' + (Zn), actually occurs. Experimental work could be focused on key samples in that system and involved DSC for thermal analysis and calorimetry, and also metallographic analysis using SEM/EDX. Experimental results verify the existence of the monotectic reaction and were also used for a quantitative thermodynamic modeling of Al-Bi-Zn. Solidification paths and microstructures of Al-Bi-Zn alloys are shown to be rather complex. Using thermodynamic calculations, these rich details involving up to three invariant reactions and unexpected monovariant reaction types can be clearly revealed and understood.

Management of the flabby ridge using a modified window technique and polyvinylsiloxane impression material

Directory of Open Access Journals (Sweden)

Nawaf Labban

2018-01-01

Full Text Available Flabby ridge is a common clinical finding affecting the alveolar ridges of the mandibular or maxillary arches. The anterior region of maxilla is the most affected area in edentulous patients. Dentures on flabby ridges have compromised stability, support, and retention unless adequate measures for its management are employed. Methods applied for flabby ridge management, include surgical removal and augmentation, special impression techniques, balanced distribution of occlusal loads and implant therapy. Special impressions often involve window technique for static impression of flabby area, which present multiple challenges. The purpose of this technique report is to present a modified window technique for the impression of anterior maxillary flabby tissues for improved and controlled application of polyvinylsiloxane impression material that are routinely available in dental practice.

Design of auxiliary shield for remote controlled metallographic microscope

International Nuclear Information System (INIS)

Matsui, Hiroki; Okamoto, Hisato

2014-06-01

The remote controlled optical microscope installed in the lead cell at the Reactor Fuel Examination Facility (RFEF) in Japan Atomic Energy Agency (JAEA) has been upgraded to a higher performance unit to study the effect of the microstructural evolution in clad material on the high burn-up fuel behavior under the accident condition. The optical pass of the new microscope requires a new through hole in the shielding lead wall of the cell. To meet safety regulations, auxiliary lead shieldings were designed to cover the lost shielding function of the cell wall. Particle and Heavy Ion Transport Code System (PHITS) was used to calculate and determine the shape and setting positions of the shielding unit. Seismic assessments of the unit were also performed. (author)

Metallographic analysis of irradiated RERTR-3 fuel test specimens

International Nuclear Information System (INIS)

Meyer, M. K.; Hofman, G. L.; Strain, R. V.; Clark, C. R.; Stuart, J. R.

2000-01-01

The RERTR-3 irradiation test was designed to investigate the irradiation behavior of aluminum matrix U-MO alloy dispersion fuels under high-temperature, high-fission-rate conditions. Initial postirradiation examination of RERTR-3 fuel specimens has concentrated on binary U-MO atomized fuels. The rate of matrix aluminum depletion was found to be higher than predictions based on low temperature irradiation data. Wavelength Dispersive X-ray Spectroscopy (WDS) indicates that aluminum is present in the interior of the fuel particles. WDS data is supported by a mass and volume balance calculation performed on the basis of image analysis results. The depletion of matrix aluminum seems to have no detrimental effects on fuel performance under the conditions tested to date

A metallographic examination of structural degradation during creep-fatigue

International Nuclear Information System (INIS)

Hales, R.

1979-07-01

A series of specimens of T316 stainless steel, which had been tested under creep-fatigue conditions, has been examined by optical and scanning electron microscopy. The development of cavities which are associated with grain-boundary carbide precipitates has been recorded. These cavities increase in size and number with increasing hold time at peak tensile strain and cause the propagating fatigue crack to follow an intergranular path. At a strain range of +- 0.25% the dominant damage mechanism is due to creep damage when the tensile hold time is greater than one minute. The fatigue crack which causes final failure is nucleated at a stress raiser and it is possible that in a smooth specimen failure may occur without the nucleation of a fatigue crack at all but rather by ductile shearing. (author)

Express: the reliability of complex systems and artificial intelligence techniques

International Nuclear Information System (INIS)

Ancelin, C.; Le, P.; Saint-Quentin, S. de

1987-01-01

The probabilistic safety study for the Paluel nuclear power station, commissioned by EDF in 1986, involved development of data processing methods and equipment which was to be given an entirely new impetus by the use of artificial intelligence techniques. The authors describe the salient features of the approach which was adopted and the lessons learnt from the way it was applied in practice [fr

E-Learning System Using Segmentation-Based MR Technique for Learning Circuit Construction

Science.gov (United States)

Takemura, Atsushi

2016-01-01

This paper proposes a novel e-Learning system using the mixed reality (MR) technique for technical experiments involving the construction of electronic circuits. The proposed system comprises experimenters' mobile computers and a remote analysis system. When constructing circuits, each learner uses a mobile computer to transmit image data from the…

Hot laboratory in Saclay. Equipment and radio-metallurgy technique of the hot lab in Saclay. Description of hot cell for handling of plutonium salts. Installation of an hot cell

International Nuclear Information System (INIS)

Bazire, R.; Blin, J.; Cherel, G.; Duvaux, Y.; Cherel, G.; Mustelier, J.P.; Bussy, P.; Gondal, G.; Bloch, J.; Faugeras, P.; Raggenbass, A.; Raggenbass, P.; Fufresne, J.

1959-01-01

Describes the conception and installation of the hot laboratory in Saclay (CEA, France). The construction ended in 1958. The main aim of this laboratory is to examine fuel rods of EL2 and EL3 as well as nuclear fuel studies. It is placed in between both reactors. In a first part, the functioning and specifications of the hot lab are given. The different hot cells are described with details of the ventilation and filtration system as well as the waste material and effluents disposal. The different safety measures are explained: description of the radiation protection, decontamination room and personnel monitoring. The remote handling equipment is composed of cutting and welding machine controlled with manipulators. Periscopes are used for sight control of the operation. In a second part, it describes the equipment of the hot lab. The unit for an accurate measurement of the density of irradiated uranium is equipped with an high precision balance and a thermostat. The equipment used for the working of irradiated uranium is described and the time length of each operation is given. There is also an installation for metallographic studies which is equipped with a manipulation bench for polishing and cleaning surfaces and a metallographic microscope. X-ray examination of uranium pellets will also be made and results will be compared with those of metallography. The last part describes the hot cells used for the manipulation of plutonium salts. The plutonium comes from the reprocessing plant and arrived as a nitric solution. Thus these cells are used to study the preparation of plutonium fluorides from nitric solution. The successive operations needed are explained: filtration, decontamination and extraction with TBP, purification on ion exchangers and finally formation of the plutonium fluorides. Particular attention has been given to the description of the specifications of the different gloveboxes and remote handling equipment used in the different reaction steps and

T1 and T2 mapping for evaluation of myocardial involvement in patients with ANCA-associated vasculitides.

Science.gov (United States)

Greulich, Simon; Mayr, Agnes; Kitterer, Daniel; Latus, Joerg; Henes, Joerg; Steubing, Hannah; Kaesemann, Philipp; Patrascu, Alexandru; Greiser, Andreas; Groeninger, Stefan; Braun, Niko; Alscher, M Dominik; Sechtem, Udo; Mahrholdt, Heiko

2017-01-06

Myocardial involvement in AAV patients might be silent, presenting with no or nonspecific symptoms, normal ECG, and preserved left-ventricular ejection fraction (LV-EF). Since up to 50% of deaths in these patients may be due to myocardial involvement, a reliable diagnostic tool is warranted. In contrast to LGE-CMR, which has its strengths in detecting focal inflammatory or fibrotic processes, recent mapping techniques are able to detect even subtle, diffuse inflammatory or fibrotic processes. Our study sought to investigate ANCA (antineutrophil cytoplasmic antibody) associated vasculitides (AAV) patients for myocardial involvement by a cardiovascular magnetic resonance (CMR) protocol, including late gadolinium enhancement (LGE) and mapping sequences. Thirty seven AAV patients were prospectively enrolled and underwent CMR imaging. Twenty healthy volunteers served as controls. Mean LV-EF was 64%; LGE prevalence of the AAV patients was 43%. AAV patients had higher median native T1 (988 vs. 952 ms, p T2 (53 vs. 49 ms, p T2 in AAV patients showed the highest prevalence of abnormally increased values beyond the 95% percentile of controls. AAV patients demonstrated increased T1, ECV, and T2 values, with native T1 and T2 showing the highest prevalence of values beyond the 95% percentile of normal. Since these findings seem to be independent of LGE, mapping techniques may provide complementary information to LGE-CMR in the assessment of myocardial involvement in patients with AAV.

Determining plutonium mass in spent fuel with non-destructive assay techniques - NGSU research overview and update on 6 NDA techniques

Energy Technology Data Exchange (ETDEWEB)

Tobin, Stephen J [Los Alamos National Laboratory; Conlin, Jeremy L [Los Alamos National Laboratory; Evans, Louise G [Los Alamos National Laboratory; Hu, Jianwei [Los Alamos National Laboratory; Blanc, Pauline C [Los Alamos National Laboratory; Lafleur, Adrienne M [Los Alamos National Laboratory; Menlove, Howard O [Los Alamos National Laboratory; Schear, Melissa A [Los Alamos National Laboratory; Swinhoe, Martyn T [Los Alamos National Laboratory; Croft, Stephen [Los Alamos National Laboratory; Fensin, Michael L [Los Alamos National Laboratory; Freeman, Corey R [Los Alamos National Laboratory; Koehler, William E [Los Alamos National Laboratory; Mozin, V [Los Alamos National Laboratory; Sandoval, N P [Los Alamos National Laboratory; Lee, T H [KAERI; Cambell, L W [PNNL; Cheatham, J R [ORNL; Gesh, C J [PNNL; Hunt, A [IDAHO STATE UNIV; Ludewigt, B A [LBNL; Smith, L E [PNNL; Sterbentz, J [INL

2010-09-15

This poster is one of two complementary posters. The Next Generation Safeguards Initiative (NGSI) of the U.S. DOE has initiated a multi-lab/university collaboration to quantify the plutonium (Pu) mass in, and detect the diversion of pins from, spent nuclear fuel assemblies with non-destructive assay (NDA). This research effort has the goal of quantifying the capability of 14 NDA techniques as well as training a future generation of safeguards practitioners. By November of 2010, we will be 1.5 years into the first phase (2.5 years) of work. This first phase involves primarily Monte Carlo modelling while the second phase (also 2.5 years) will focus on experimental work. The goal of phase one is to quantify the detection capability of the various techniques for the benefit of safeguard technology developers, regulators, and policy makers as well as to determine what integrated techniques merit experimental work, We are considering a wide range of possible technologies since our research horizon is longer term than the focus of most regulator bodies. The capability of all of the NDA techniques will be determined for a library of 64 17 x 17 PWR assemblies [burnups (15, 30, 45, 60 GWd/tU), initial enrichments (2, 3, 4, 5%) and cooling times (1, 5, 20, 80 years)]. The burnup and cooling time were simulated with each fuel pin being comprised of four radial regions. In this paper an overview of the purpose will be given as well as a technical update on the following 6 neutron techniques: {sup 252}Cf Interrogation with Prompt Neutron Detection, Delayed Neutrons, Differential Die-Away, Differential Die-Away Self-Interrogation, Passive Neutron Albedo Reactivity, Self-Integration Neutron Resonance Densitometry. The technical update will quantify the anticipated performance of each technique for the 64 assemblies of the spent fuel library.

Determining plutonium mass in spent fuel with non-destructive assay techniques - NGSI research overview and update on 6 NDA techniques

International Nuclear Information System (INIS)

Tobin, Stephen J.; Conlin, Jeremy L.; Evans, Louise G.; Hu, Kianwei; Blanc, P.C.; Lafleur, Am; Menlove, H.O.; Schear, M.A.; Swinhoe, M.T.; Croft, S.; Fensin, M.L.; Freeman, C.R.; Koehler, W.E.; Mozin, V.; Sandoval, N.P.; Lee, T.H.; Cambell, L.W.; Cheatham, J.R.; Gesh, C.J.; Hunt, A.; Ludewigt, B.A.; Smith, L.E.; Sterbentz, J.

2010-01-01

This poster is one of two complementary posters. The Next Generation Safeguards Initiative (NGSI) of the U.S. DOE has initiated a multi-lab/university collaboration to quantify the plutonium (Pu) mass in, and detect the diversion of pins from, spent nuclear fuel assemblies with non-destructive assay (NDA). This research effort has the goal of quantifying the capability of 14 NDA techniques as well as training a future generation of safeguards practitioners. By November of 2010, we will be 1.5 years into the first phase (2.5 years) of work. This first phase involves primarily Monte Carlo modelling while the second phase (also 2.5 years) will focus on experimental work. The goal of phase one is to quantify the detection capability of the various techniques for the benefit of safeguard technology developers, regulators, and policy makers as well as to determine what integrated techniques merit experimental work, We are considering a wide range of possible technologies since our research horizon is longer term than the focus of most regulator bodies. The capability of all of the NDA techniques will be determined for a library of 64 17 x 17 PWR assemblies (burnups (15, 30, 45, 60 GWd/tU), initial enrichments (2, 3, 4, 5%) and cooling times (1, 5, 20, 80 years)). The burnup and cooling time were simulated with each fuel pin being comprised of four radial regions. In this paper an overview of the purpose will be given as well as a technical update on the following 6 neutron techniques: 252 Cf Interrogation with Prompt Neutron Detection, Delayed Neutrons, Differential Die-Away, Differential Die-Away Self-Interrogation, Passive Neutron Albedo Reactivity, Self-Integration Neutron Resonance Densitometry. The technical update will quantify the anticipated performance of each technique for the 64 assemblies of the spent fuel library.

New autocorrelation technique for the IR FEL optical pulse width measurements

Energy Technology Data Exchange (ETDEWEB)

Amirmadhi, F.; Brau, K.A.; Becker, C. [Vanderbilt Univ., Nashville, TN (United States)] [and others

1995-12-31

We have developed a new technique for the autocorrelation measurement of optical pulse width at the Vanderbilt University FEL center. This method is based on nonlinear absorption and transmission characteristics of semiconductors such as Ge, Te and InAs suitable for the wavelength range from 2 to over 6 microns. This approach, aside being simple and low cost, removes the phase matching condition that is generally required for the standard frequency doubling technique and covers a greater wavelength range per nonlinear material. In this paper we will describe the apparatus, explain the principal mechanism involved and compare data which have been acquired with both frequency doubling and two-photon absorption.

Percutaneous rendezvous technique for the management of a bile duct injury.

Science.gov (United States)

Meek, James; Fletcher, Savannah; Crumley, Kristen; Culp, W C; Meek, Mary

2018-02-01

The rendezvous technique typically involves combined efforts of interventional radiology, endoscopy, and surgery. It can be done solely percutaneously, whereby the interventionalist gains desired access to one point in the body by approaching it from two different access sites. We present the case of a woman who underwent cholecystectomy complicated by a bile duct injury. A percutaneous rendezvous procedure enabled placement of an internal-external drain from the intrahepatic ducts through the biloma and distal common bile duct and into the duodenum. Thus, a percutaneous rendezvous technique is feasible for managing a bile duct injury when endoscopic retrograde cholangio-pancreatography or percutaneous transhepatic cholangiogram alone has been unsuccessful.

Percutaneous rendezvous technique for the management of a bile duct injury

Directory of Open Access Journals (Sweden)

James Meek, DO

2018-02-01

Full Text Available The rendezvous technique typically involves combined efforts of interventional radiology, endoscopy, and surgery. It can be done solely percutaneously, whereby the interventionalist gains desired access to one point in the body by approaching it from two different access sites. We present the case of a woman who underwent cholecystectomy complicated by a bile duct injury. A percutaneous rendezvous procedure enabled placement of an internal-external drain from the intrahepatic ducts through the biloma and distal common bile duct and into the duodenum. Thus, a percutaneous rendezvous technique is feasible for managing a bile duct injury when endoscopic retrograde cholangio-pancreatography or percutaneous transhepatic cholangiogram alone has been unsuccessful.

[Inheritance and evolution of acupuncture manipulation techniques of Zhejiang acupuncture masters in modern times].

Science.gov (United States)

Yu, Daxiong; Ma, Ruijie; Fang, Jianqiao

2015-05-01

There are many eminent acupuncture masters in modern times in the regions of Zhejiang province, which has developed the acupuncture schools of numerous characteristics and induces the important impacts at home and abroad. Through the literature collection on the acupuncture schools in Zhejiang and the interviews to the parties involved, it has been discovered that the acupuncture manipulation techniques of acupuncture masters in modern times are specifically featured. Those techniques are developed on the basis of Neijing (Internal Classic), Jinzhenfu (Ode to Gold Needle) and Zhenjiu Dacheng (Great Compendium of Acupuncture and Moxibustion). No matter to obey the old maxim or study by himself, every master lays the emphasis on the research and interpretation of classical theories and integrates the traditional with the modern. In the paper, the acupuncture manipulation techniques of Zhejiang acupuncture masters in modern times are stated from four aspects, named needling techniques in Internal Classic, feijingzouqi needling technique, penetrating needling technique and innovation of acupuncture manipulation.

Applied measuring techniques for the investigation of time-dependent flow phenomena in centrifugal compressors

International Nuclear Information System (INIS)

Hass, U.; Haupt, U.; Jansen, M.; Kassens, K.; Knapp, P.; Rautenberg, M.

1978-01-01

During the past 10 years new measuring techniques have been developed for the experimental investigation of highly loaded centrifugal compressors. These measuring techniques take into account the time dependency of the fluctuating physical quantities such as pressure, temperature, and velocity. Some key points of these experimental techniques are shown and explained in this paper. An important basis for such measurements is the accurate dynamic calibration of the measuring apparatus. In addition, some problems involved analyzing measured signals are dealt with and pressure measurements and their interpretation are shown. Finally optical, acoustical and vibrational measuring procedures are described which are additionally used for the investigation of non-stationary flow phenomena. (orig.) [de

Microscale and nanoscale strain mapping techniques applied to creep of rocks

Science.gov (United States)

Quintanilla-Terminel, Alejandra; Zimmerman, Mark E.; Evans, Brian; Kohlstedt, David L.

2017-07-01

Usually several deformation mechanisms interact to accommodate plastic deformation. Quantifying the contribution of each to the total strain is necessary to bridge the gaps from observations of microstructures, to geomechanical descriptions, to extrapolating from laboratory data to field observations. Here, we describe the experimental and computational techniques involved in microscale strain mapping (MSSM), which allows strain produced during high-pressure, high-temperature deformation experiments to be tracked with high resolution. MSSM relies on the analysis of the relative displacement of initially regularly spaced markers after deformation. We present two lithography techniques used to pattern rock substrates at different scales: photolithography and electron-beam lithography. Further, we discuss the challenges of applying the MSSM technique to samples used in high-temperature and high-pressure experiments. We applied the MSSM technique to a study of strain partitioning during creep of Carrara marble and grain boundary sliding in San Carlos olivine, synthetic forsterite, and Solnhofen limestone at a confining pressure, Pc, of 300 MPa and homologous temperatures, T/Tm, of 0.3 to 0.6. The MSSM technique works very well up to temperatures of 700 °C. The experimental developments described here show promising results for higher-temperature applications.

Timber Elements: Traditional and Modern Strengthening Techniques

Directory of Open Access Journals (Sweden)

Raluca Hohan

2010-01-01

Full Text Available The main idea of this paper is to analyse the means for the rehabilitation of our cultural heritage timber structures. Several methods together with their application techniques are described, and also, the reasons for what these strengthening operations become imminent at a point. First of all, the necessity of the timber structural elements strengthening is explained through a short presentation of the factors which are degrading the material. Then, certain precautions and strengthening procedures are presented, all involving the usage of traditional materials like wood, metal, or concrete, and of modern materials like fiber reinforced polymeric composite.

Work hours and work-family conflict: the double-edged sword of involvement in work and family.

Science.gov (United States)

Matthews, Russell A; Swody, Cathleen A; Barnes-Farrell, Janet L

2012-08-01

In this study, we examine the role of work hours in a model that incorporates involvement in both work and family with experiences of work-family conflict and subjective well-being. Self-report data were collected from 383 full-time employees and analysed using structural equation modelling techniques. Results demonstrate that role salience was positively related to behavioural involvement with work and with family. In turn, behavioural family involvement was negatively related to work hours and family-to-work conflict, while behavioural work involvement was positively related to work hours. Behavioural family involvement was also positively related to life satisfaction. Finally, both family-to-work conflict and end-of-workday strain were negatively related to life satisfaction. Our results provide insight into unexpected problems that might arise when employees place overly high importance on work and work long hours. This study serves as a foundation for researchers to examine the interplay of time spent with work and family with other aspects of the work-family interface. Copyright © 2011 John Wiley & Sons, Ltd.

Scanning tunneling microscopy II further applications and related scanning techniques

CERN Document Server

Güntherodt, Hans-Joachim

1995-01-01

Scanning Tunneling Microscopy II, like its predecessor, presents detailed and comprehensive accounts of the basic principles and broad range of applications of STM and related scanning probe techniques. The applications discussed in this volume come predominantly from the fields of electrochemistry and biology. In contrast to those described in STM I, these studies may be performed in air and in liquids. The extensions of the basic technique to map other interactions are described in chapters on scanning force microscopy, magnetic force microscopy, and scanning near-field optical microscopy, together with a survey of other related techniques. Also described here is the use of a scanning proximal probe for surface modification. Together, the two volumes give a comprehensive account of experimental aspects of STM. They provide essential reading and reference material for all students and researchers involved in this field. In this second edition the text has been updated and new methods are discussed.

Hot laboratory in Saclay. Equipment and radio-metallurgy technique of the hot lab in Saclay. Description of hot cell for handling of plutonium salts. Installation of an hot cell; Laboratoire a tres haute activite de Saclay. Equipement et techniques radiometallurgiques du laboratoire a haute activite de Saclay. Description de cellules pour manipulation de sels de plutonium. Amenagement d'une cellule du laboratoire de haute activite

Energy Technology Data Exchange (ETDEWEB)

Bazire, R; Blin, J; Cherel, G; Duvaux, Y; Cherel, G; Mustelier, J P; Bussy, P; Gondal, G; Bloch, J; Faugeras, P; Raggenbass, A; Raggenbass, P; Fufresne, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1959-07-01

Describes the conception and installation of the hot laboratory in Saclay (CEA, France). The construction ended in 1958. The main aim of this laboratory is to examine fuel rods of EL2 and EL3 as well as nuclear fuel studies. It is placed in between both reactors. In a first part, the functioning and specifications of the hot lab are given. The different hot cells are described with details of the ventilation and filtration system as well as the waste material and effluents disposal. The different safety measures are explained: description of the radiation protection, decontamination room and personnel monitoring. The remote handling equipment is composed of cutting and welding machine controlled with manipulators. Periscopes are used for sight control of the operation. In a second part, it describes the equipment of the hot lab. The unit for an accurate measurement of the density of irradiated uranium is equipped with an high precision balance and a thermostat. The equipment used for the working of irradiated uranium is described and the time length of each operation is given. There is also an installation for metallographic studies which is equipped with a manipulation bench for polishing and cleaning surfaces and a metallographic microscope. X-ray examination of uranium pellets will also be made and results will be compared with those of metallography. The last part describes the hot cells used for the manipulation of plutonium salts. The plutonium comes from the reprocessing plant and arrived as a nitric solution. Thus these cells are used to study the preparation of plutonium fluorides from nitric solution. The successive operations needed are explained: filtration, decontamination and extraction with TBP, purification on ion exchangers and finally formation of the plutonium fluorides. Particular attention has been given to the description of the specifications of the different gloveboxes and remote handling equipment used in the different reaction steps and

Hot laboratory in Saclay. Equipment and radio-metallurgy technique of the hot lab in Saclay. Description of hot cell for handling of plutonium salts. Installation of an hot cell; Laboratoire a tres haute activite de Saclay. Equipement et techniques radiometallurgiques du laboratoire a haute activite de Saclay. Description de cellules pour manipulation de sels de plutonium. Amenagement d'une cellule du laboratoire de haute activite

Energy Technology Data Exchange (ETDEWEB)

Bazire, R.; Blin, J.; Cherel, G.; Duvaux, Y.; Cherel, G.; Mustelier, J.P.; Bussy, P.; Gondal, G.; Bloch, J.; Faugeras, P.; Raggenbass, A.; Raggenbass, P.; Fufresne, J. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1959-07-01

Describes the conception and installation of the hot laboratory in Saclay (CEA, France). The construction ended in 1958. The main aim of this laboratory is to examine fuel rods of EL2 and EL3 as well as nuclear fuel studies. It is placed in between both reactors. In a first part, the functioning and specifications of the hot lab are given. The different hot cells are described with details of the ventilation and filtration system as well as the waste material and effluents disposal. The different safety measures are explained: description of the radiation protection, decontamination room and personnel monitoring. The remote handling equipment is composed of cutting and welding machine controlled with manipulators. Periscopes are used for sight control of the operation. In a second part, it describes the equipment of the hot lab. The unit for an accurate measurement of the density of irradiated uranium is equipped with an high precision balance and a thermostat. The equipment used for the working of irradiated uranium is described and the time length of each operation is given. There is also an installation for metallographic studies which is equipped with a manipulation bench for polishing and cleaning surfaces and a metallographic microscope. X-ray examination of uranium pellets will also be made and results will be compared with those of metallography. The last part describes the hot cells used for the manipulation of plutonium salts. The plutonium comes from the reprocessing plant and arrived as a nitric solution. Thus these cells are used to study the preparation of plutonium fluorides from nitric solution. The successive operations needed are explained: filtration, decontamination and extraction with TBP, purification on ion exchangers and finally formation of the plutonium fluorides. Particular attention has been given to the description of the specifications of the different gloveboxes and remote handling equipment used in the different reaction steps and

Analyzing injury severity factors at highway railway grade crossing accidents involving vulnerable road users: A comparative study.

Science.gov (United States)

Ghomi, Haniyeh; Bagheri, Morteza; Fu, Liping; Miranda-Moreno, Luis F

2016-11-16

The main objective of this study is to identify the main factors associated with injury severity of vulnerable road users (VRUs) involved in accidents at highway railroad grade crossings (HRGCs) using data mining techniques. This article applies an ordered probit model, association rules, and classification and regression tree (CART) algorithms to the U.S. Federal Railroad Administration's (FRA) HRGC accident database for the period 2007-2013 to identify VRU injury severity factors at HRGCs. The results show that train speed is a key factor influencing injury severity. Further analysis illustrated that the presence of illumination does not reduce the severity of accidents for high-speed trains. In addition, there is a greater propensity toward fatal accidents for elderly road users compared to younger individuals. Interestingly, at night, injury accidents involving female road users are more severe compared to those involving males. The ordered probit model was the primary technique, and CART and association rules act as the supporter and identifier of interactions between variables. All 3 algorithms' results consistently show that the most influential accident factors are train speed, VRU age, and gender. The findings of this research could be applied for identifying high-risk hotspots and developing cost-effective countermeasures targeting VRUs at HRGCs.

Using Delphi technique in a consensual curriculum for periodontics.

Science.gov (United States)

Fried, Hana; Leao, Anna Thereza

2007-11-01

Periodontics has experienced several important conceptual changes in the last few decades. As such, it is important to have a periodontics curriculum built upon the expertise of specialists in that discipline and reflecting those changes. The main goal of this study was to attain a consensus, through the use of the Delphi technique, on the topics that should be included in a periodontics curriculum for undergraduate dental students. A sample of periodontics lecturers from nine dental schools in two Brazilian cities was used, and a Delphi technique approach was followed to investigate sample member perceptions on the subject. Participants received four postal mail questionnaires asking them to rate and rerate eighty-nine topics for possible inclusion in the curriculum. A descriptive analysis was conducted, and topic frequencies were calculated. Topics rated as highly important for inclusion were the following: health, ailment, prevention, etiology, epidemiology, diagnosis, and treatment. The Delphi technique approach proved successful in involving periodontics lecturers in the design of a periodontics curriculum for undergraduate dental students.

Authenticity study of Phyllanthus species by NMR and FT-IR techniques coupled with chemometric methods

International Nuclear Information System (INIS)

Santos, Maiara S.; Pereira-Filho, Edenir R.; Ferreira, Antonio G.; Boffo, Elisangela F.; Figueira, Glyn M.

2012-01-01

The importance of medicinal plants and their use in industrial applications is increasing worldwide, especially in Brazil. Phyllanthus species, popularly known as 'quebra-pedras' in Brazil, are used in folk medicine for treating urinary infections and renal calculus. This paper reports an authenticity study, based on herbal drugs from Phyllanthus species, involving commercial and authentic samples using spectroscopic techniques: FT-IR, 1 H HR-MAS NMR and 1 H NMR in solution, combined with chemometric analysis. The spectroscopic techniques evaluated, coupled with chemometric methods, have great potential in the investigation of complex matrices. Furthermore, several metabolites were identified by the NMR techniques. (author)

Anatomy of Sodium Hypochlorite Accidents Involving Facial Ecchymosis – A Review

Science.gov (United States)

Zhu, Wan-chun; Gyamfi, Jacqueline; Niu, Li-na; Schoeffel, G. John; Liu, Si-ying; Santarcangelo, Filippo; Khan, Sara; Tay, Kelvin C-Y.; Pashley, David H.; Tay, Franklin R.

2013-01-01

Objectives Root canal treatment forms an essential part of general dental practice. Sodium hypochlorite (NaOCl) is the most commonly used irrigant in endodontics due to its ability to dissolve organic soft tissues in the root canal system and its action as a potent antimicrobial agent. Although NaOCl accidents created by extrusion of the irrigant through root apices are relatively rare and are seldom life-threatening, they do create substantial morbidity when they occur. Methods To date, NaOCl accidents have only been published as isolated case reports. Although previous studies have attempted to summarise the symptoms involved in these case reports, there was no endeavor to analyse the distribution of soft tissue distribution in those reports. In this review, the anatomy of a classical NaOCl accident that involves facial swelling and ecchymosis is discussed. Results By summarising the facial manifestations presented in previous case reports, a novel hypothesis that involves intravenous infusion of extruded NaOCl into the facial vein via non-collapsible venous sinusoids within the cancellous bone is presented. Conclusions Understanding the mechanism involved in precipitating a classic NaOCl accident will enable the profession to make the best decision regarding the choice of irrigant delivery techniques in root canal débridement, and for manufacturers to design and improve their irrigation systems to achieve maximum safety and efficient cleanliness of the root canal system. PMID:23994710

JOINT INVOLVEMENT IN SYPHILIS

Directory of Open Access Journals (Sweden)

T. I. Zlobina

2016-01-01

Full Text Available Joint involvement in syphilis has been considered as casuistry in recent years. At the same time, the high incidence of primary syphilis and the notified cases of late neurosyphilis may suggest that joint involvement in this disease is by no means always verified. Traditionally there are two forms of syphilitic arthritis: primary synovial (involving the articular membranes and sac and primary bone (involving the articular bones and cartilages ones. The paper describes the authors' clinical case of the primary bone form of articular syphilis in a 34-year-old man. 

Motivational Influences on Cognition: Task Involvement, Ego Involvement, and Depth of Information Processing.

Science.gov (United States)

Graham, Sandra; Golan, Shari

1991-01-01

Task involvement and ego involvement were studied in relation to depth of information processing for 126 fifth and sixth graders in 2 experiments. Ego involvement resulted in poorer word recall at deep rather than shallow information processing levels. Implications for the study of motivation are discussed. (SLD)

Evaluation of AISI 4140 Steel Repair Without Post-Weld Heat Treatment

Science.gov (United States)

Silva, Cleiton C.; de Albuquerque, Victor H. C.; Moura, Cícero R. O.; Aguiar, Willys M.; Farias, Jesualdo P.

2009-04-01

The present work evaluates the two-layer technique on the heat affected zone (HAZ) of AISI 4140 steel welded with different heat input levels between the first and second layer. The weld heat input levels selected by the Higuchi test were 5/5, 5/10, and 15/5 kJ/cm. The evaluation of the refining and/or tempering of the coarsened grain HAZ of the first layer was carried out using metallographic tests, microhardness measurements, and the Charpy-V impact test. The tempering of the first layer was only reached when the weld heat input ratio was 5/5 kJ/cm. The results of the Charpy-V impact test showed that the two-layer technique was efficient, from the point of view of toughness, since the toughness values reached were greater than the base metal for all weld heat input ratios applied. The results obtained indicate that the best performance of the two-layer deposition technique was for the weld heat input ratio 5/5 kJ/cm employing low heat input.

Assessment of tumors of the lung apex by imaging techniques

International Nuclear Information System (INIS)

Rueda, J.; Serrano, F.; Pain, M.I.; Rodriguez, F.

1996-01-01

The purpose of this study was to analyze the value of MR in the preoperative staging of tumors of the lung apex and detection of local invasion of adjacent structures to determine its influence on the therapeutic approach. We obtained plain X-ray images in two planes, as well as CT and Mr images, in 12 patients with Pan coast tumor in whom there was surgical (n=8) or clinical (n=4) evidence of invasion. The objective was to assess local infiltration of brain stem and chest wall soft tissue, enveloping of the subclavian artery, substantial involvement of the brachial plexus and destruction of the vertebral body. In our series, MR was superior to the other imaging techniques in predicting the involvement of the structures surrounding the tumor. In conclusion, MR should be performed in a patient diagnosed by plain radiography as having an apical tumors to assess local tumor extension, while CT should be done to detect mediastinal lymph node involvement and distant metastases. 19 refs

Instrument setpoints and data gathering techniques

International Nuclear Information System (INIS)

Leong, J.L.; Ornellas, R.P.; Atkinson, J.L.; Gross, R.S.

1994-01-01

Setpoint calculation project sizes vary greatly depending upon the level of effort required and can generally be classified as small or large depending on the number of setpoint calculations required. Small projects usually consist of new system upgrades, power uprates, and the utility's response to industry wide issues and concerns, and require between 10 and 120 setpoint calculations. Large projects usually involve design basis reconstitutions and the complete recalculating of all setpoints prioritized on system or safety related bases. Both large and small project schedules are usually directly tied to Nuclear Regulatory Commission (NRC) commitment dates and it is not uncommon for a large project to take 2 to 3 years to complete. Setpoint calculation projects have historically been performed by the brute force technique employing a variety of methodologies. The brute force technique typically employed today involves putting together a project team large enough to perform all the scheduled setpoint calculations. Setpoint calculations vary in size and complexity and, therefore, may require a wide range of man-hours of a qualified instrument setpoint engineer's time to perform instrument input data retrieval, resolve conflicting input data values, and complete the calculation. The actual time to perform the setpoint calculation using a computer program to calculate results is relatively small in comparison with the time required for data collection and the preparation of supporting documentation. Three major issues have traditionally plagued setpoint calculation projects: data collection; methodology; and incomplete and inconsistent calculations. These traditional problems are addressed and an innovative solution to performing instrument setpoint calculation projects is presented. Through the use of the POWRTRAK database and powerful computer software programs, a new solution to an old and persistent industry challenge is established

DESIGN & ANALYSIS TOOLS AND TECHNIQUES FOR AEROSPACE STRUCTURES IN A 3D VISUAL ENVIRONMENT

Directory of Open Access Journals (Sweden)

Radu BISCA

2009-09-01

Full Text Available The main objective of this project is to develop a set of tools and to integrate techniques in a software package which is build on structure analysis applications based on Romanian engineers experience in designing and analysing aerospace structures, consolidated with the most recent methods and techniques. The applications automates the structure’s design and analysis processes and facilitate the exchange of technical information between the partners involved in a complex aerospace project without limiting the domain.

Consumer involvement profiles: An application of consumer involvement in mobile industry

Directory of Open Access Journals (Sweden)

Homa Rahbarian

2014-04-01

Full Text Available This paper investigates consumer involvement profile among people who intend to purchase mobile devises. The study considers the effects of various factors influencing on purchase intention including consumers’ personal characteristics such as age, gender, income as well as some external factors including advertisement. The study uses a questionnaire in Likert scale, originally developed by O’Cass (2000 [O’Cass, A. (2000. An assessment of consumers' product, purchase decision, advertising and consumption involvement in fashion clothing. Journal of Economic Psychology, 21, 545-576.]. The questionnaire has been distributed among 385 people, randomly who purchased mobile devices from a mall in city of Tehran, Iran. Using Pearson correlation test, the study has concluded that oral advertisement as well as consumer purchase involvement have positive and strong relationship with consumer’s purchase intention. In terms of age, people aged 20-30 maintained the highest purchase intention. In addition, in terms of gender, men had more purchase involvement than women did.

Novel in-situ lamella fabrication technique for in-situ TEM.

Science.gov (United States)

Canavan, Megan; Daly, Dermot; Rummel, Andreas; McCarthy, Eoin K; McAuley, Cathal; Nicolosi, Valeria

2018-03-29

In-situ transmission electron microscopy is rapidly emerging as the premier technique for characterising materials in a dynamic state on the atomic scale. The most important aspect of in-situ studies is specimen preparation. Specimens must be electron transparent and representative of the material in its operational state, amongst others. Here, a novel fabrication technique for the facile preparation of lamellae for in-situ transmission electron microscopy experimentation using focused ion beam milling is developed. This method involves the use of rotating microgrippers during the lift-out procedure, as opposed to the traditional micromanipulator needle and platinum weld. Using rotating grippers, and a unique adhesive substance, lamellae are mounted onto a MEMS device for in-situ TEM annealing experiments. We demonstrate how this technique can be used to avoid platinum deposition as well as minimising damage to the MEMS device during the thinning process. Our technique is both a cost effective and readily implementable alternative to the current generation of preparation methods for in-situ liquid, electrical, mechanical and thermal experimentation within the TEM as well as traditional cross-sectional lamella preparation. Copyright © 2018 Elsevier B.V. All rights reserved.

Gamma scan technique for detecting coupon inside the mother pipeline

International Nuclear Information System (INIS)

Rasif Mohd Zain; Roslan Yahya; Mohamad Rabaie Shari; Airwan Affandi Mahmood; Mior Ahmad Khusaini Adnan

2012-01-01

Many times a year natural gas transmission and distribution companies need to make new connections to pipelines to expand or modify their existing system through hot tapping procedure. This procedure involves the installation of a new pipeline connection while the pipeline remains in service, flowing natural gas under pressure. The hot tap procedure includes attaching a branch connection and valve on the outside of an operating pipeline, and then cutting out the pipe-line wall within the branch and removing the wall section, which is called object of coupon through the valve. During the hot tapping process a critical problems occurred when a coupon fell into the mother pipeline. To overcome this problem, a gamma-ray absorption technique was chosen whereby a mapping technique will be done to detect the coupon position. The technique is non-destructive as it applies Co-60 (5 mCi) as a radioisotope sealed source to emit gamma radiation and a NaI(Tl) scintillation as detector. The result provided a visible representation of density profile inside pipeline where the coupon location can be located. This paper provides the detail of the technique used and presents the result obtained. (author)

Some stochastic techniques in quantization, new developments in Markov fields and quantum fields

International Nuclear Information System (INIS)

Albeverio, S.; Zegarlinski, B.

1990-01-01

In these lectures we intend to discuss a few recent developments in the area of interactions between quantum fields and Markow fields in which we have been involved. We stress particularly developments involving techniques of stochastic analysis and where mathematical results have been obtained. In sections 1 and 2 we discuss recent developments in the study and applications of the theory of Dirichlet forms in its relations with quantum mechanics and quantum field theory. In our opinion, this theory provides a natural setting for the study of the singular stochastic processes associated with quantum theory. In section 3 we discuss a recent rigorous construction of a convergent simplicial approximation to quantum fields. We look upon these developments as a first step towards a mathematical realization, at least in 2 space-time dimensions, of a convergent 'Regge-calculus', and as first steps to the mathematical control of more general models (like e.g. models involving actions of Chern-Simons type) in the continuum. In Sect. 4 we discuss applications of some stochastic techniques to the study of gauge fields and Higgs fields, mainly in 2 space time dimensions and certain non linear electromagnetic-type fields in 4-space-time dimensions. (orig./HSI)

Alternative technique of cervical spinal stabilization employing lateral mass plate and screw and intra-articular spacer fixation

Directory of Open Access Journals (Sweden)

Atul Goel

2013-01-01

Full Text Available Aim: The author discusses an alternative technique of segmental cervical spinal fixation. Material and Methods: The subtleties of the technique are discussed on the basis of experience with 3 cases with a follow-up of between 30 and 36 months. Technique: The technique involves debridement of facetal articular cartilage, distraction of facets, jamming of ′Goel spacer′ into the articular cavity and fortification of the fixation by lateral mass plate and screw fixation. The ′double-insurance′ method of fixation is safe for vertebral artery, nerve roots and spinal neural structures and the fixation is strong. Conclusions: The discussed technique is safe and provides a strong fixation and a ground for ultimate arthrodesis.

Parent Involvement Handbook.

Science.gov (United States)

Caplan, Arna

This handbook on parent involvement, designed to be used with preschool programs, was developed by the Jefferson County Public Schools in Lakewood, Colorado. Included are: (1) a general statement about parent involvement in an early childhood program, (2) a description of the Jefferson County Early Childhood Program, (3) a description of the…

A Technique: Exposure Therapy

Directory of Open Access Journals (Sweden)

Serkan AKKOYUNLU

2013-07-01

Full Text Available Introduction: Exposure with response prevention is an effective treatment for all anxiety disorders. According to the behavioral learning theories, fears which are conditioned via classical conditioning are reinforced by respondent conditioning. Avoidance and safety seeking behaviors prevent disconfirmation of anxious beliefs. In exposure client faces stimulates or cues that elicit fear or distress, by this avoidance is inhibited. Clients are also encouraged to resists performing safety seeking behaviors or rituals that they utilize to reduce fear or distress. Accomplishing these habituation or extinction is achieved. In addition to this clients learn that feared consequences does not realize or not harmful as they believed by experiencing. Emotional processing is believed to be the mechanism of change in exposure.Objective: The aim of this review is to provide a definition of exposure and its effectiveness briefly, and describe how to implement exposure, its steps and remarkable aspects using. Exposure therapies and treatments that involve exposure are proved to be effective in all anxiety disorders. Exposure therapy can be divided in three parts: Assessment and providing a treatment rationale, creating an exposure hierarchy and response prevention plan, implementing exposure sessions. Clients must also continue to perform exposure between sessions. Therapy transcripts are also provided to exemplify these parts. Conclusion: Exposure with response prevention is a basic and effective technique. Every cognitive behavior therapist must be able to implement this technique and be cognizant of pearls of this procedure.

Transient data acquisition techniques under EDS

International Nuclear Information System (INIS)

Telford, S.

1985-06-01

This paper is the first of a series which describes the Enrichment Diagnostic System (EDS) developed for the MARS project at Lawrence Livermore National Laboratory. Although EDS was developed for use on AVLIS, the functional requirements, overall design, and specific techniques are applicable to any experimental data acquisition system involving large quantities of transient data. In particular this paper will discuss the techniques and equipment used to do the data acquisition. Included are what types of hardware are used and how that hardware (CAMAC, digital oscilloscopes) is interfaced to the HP computers. In this discussion the author will address the problems encountered and the solutions used, as well as the performance of the instrument/computer interfaces. The second topic the author will discuss is how the acquired data is associated to graphics and analysis portions of EDS through efficient real time data bases. This discussion will include how the acquired data is folded into the overall structure of EDS providing the user immediate access to raw and analyzed data. By example you will see how easily a new diagnostic can be added to the EDS structure without modifying the other parts of the system. 8 figs

Nuclear material safeguards surveillance and accountancy by isotope correlation techniques

International Nuclear Information System (INIS)

Persiani, P.J.; Goleb, J.A.

1981-01-01

This paper presents the initial phase of the US study program and involves the computation of isotopic correlations for the LMFBR fuel cycle. The LWR fuel cycle phase of the study is currently in progress. The selection of the more safeguards effective functionals will depend not only on the level of reliability of isotope correlation technique (ICT) for verification, but also on the capability and difficulty of developing measurement methods. Performance characteristics of existing and proposed isotopic measurement techniques cover the general areas including assay and isotopic wet chemistry and NDA: (1) simultaneous multicomponent analysis techniques, (2) mass spectrometry, (3) x-ray fluorescence or densitometry with high flux monochromatic x-ray sources and high dispersion spectrometers, (4) passive and active neutron interrogation, (5) high level gamma-ray spectroscopy, (6) coulometry, and (7) potentiometry. The measurement capabilities and inherent limitations of these systems are to be evaluated in terms of total systems, operational mode, sample preparation requirements and consequent effect on dissolver solution representation, accuracy and precision estimates (if available), development status of the technique, and development requirements. The isotopic correlation technique shows considerable promise for use in verifying the initial isotopic composition and burnup of discharged assemblies based on the measured ratios of several key isotopes, obtained probably at the dissolver stage in reprocessing. This technique should, for example, easily be capable of indicating the exchange of a blanket assembly for a fuel assembly

A Computational Study on the Magnetic Resonance Coupling Technique for Wireless Power Transfer

Directory of Open Access Journals (Sweden)

Zakaria N.A.

2017-01-01

Full Text Available Non-radiative wireless power transfer (WPT system using magnetic resonance coupling (MRC technique has recently been a topic of discussion among researchers. This technique discussed more scenarios in mid-range field of wireless power transmission reflected to the distance and efficiency. The WPT system efficiency varies when the coupling distance between two coils involved changes. This could lead to a decisive issue of high efficient power transfer. This paper presents case studies on the relationship of operating range with the efficiency of the MRC technique. Demonstrative WPT system operates at two different frequencies are projected in order to verify performance. The resonance frequencies used are less than 100MHz within range of 10cm to 20cm.

The use of the Ma-Griffith technique for percutaneous repair of fresh ruptured tendo Achillis.

Science.gov (United States)

Klein, W; Lang, D M; Saleh, M

1991-01-01

All patients treated for a rupture of the Achilles tendon by the technique of percutaneous repair were identified from a five year period up to 1987. A review of the patients and results of this technique was undertaken using a clinical grading system. Review was conducted between 18 and 81 months following the injury. Of 38 patients followed up, 71% achieved good results and only 8% poor results. The re-rupture rate for this series was 8%. Sural nerve involvement (13%) was found to be a troublesome complication. During the period under study, a modification to the technique was introduced which abolished this complication. We present our results and describe the modification to the technique. The importance of the use of nonabsorbable sutures is emphasized.

Ergonomic study on wrist posture when using laparoscopic tools in four different techniques regarding minimally invasive surgery.

Science.gov (United States)

Bartnicka, Joanna; Zietkiewicz, Agnieszka A; Kowalski, Grzegorz J

2018-03-19

With reference to four different minimally invasive surgery (MIS) cholecystectomy the aims were: to recognize the factors influencing dominant wrist postures manifested by the surgeon; to detect risk factors involved in maintaining deviated wrist postures; to compare the wrist postures of surgeons while using laparoscopic tools. Video films were recorded during live surgeries. The films were synchronized with wrist joint angles obtained from wireless electrogoniometers placed on the surgeon's hand. The analysis was conducted for five different laparoscopic tools used during all surgical techniques. The most common wrist posture was extension. In the case of one laparoscopic tool, the mean values defining extended wrist posture were distinct in all four surgical techniques. For one type of surgical technique, considered to be the most beneficial for patients, more extreme postures were noticed regarding all laparoscopic tools. We recognized a new factor, apart from the tool's handle design, that influences extreme and deviated wrist postures. It involves three areas of task specification including the type of action, type of motion patterns and motion dynamism. The outcomes proved that the surgical technique which is most beneficial for the patient imposes the greatest strain on the surgeon's wrist.

Evaluation of myocardial involvement in Duchenne's progressive muscular dystrophy with thallium-201 myocardial perfusion imaging

International Nuclear Information System (INIS)

Kawai, Naoki; Sotobata, Iwao; Okada, Mitsuhiro

1985-01-01

Myocardial involvement in progressive muscular dystrophy of the Duchenne type was evaluated in 19 patients using thallium-201 myocardial perfusion imaging. A qualitative analysis was performed from five projection images by three experienced physicians. Distinct perfusion defects were shown in 13 patients, especially in the LV posterolateral or posterior wall (11 patients). There was no significant relationship between the presence of perfusion defects and the skeletal muscle involvements or thoracic deformities assessed by transmission computed tomography. Extensive perfusion defects were shown in 2 patients who died of congestive heart failure 1 to 2 years after the scintigraphic study. Progression of the myocardial scintigraphic abnormalities were considered to be minimal in 7 of 9 patients who underwent two serial scintigraphic studies over 2 to 3 years. It was concluded that thallium myocardial perfusion imaging is a useful clinical technique to assess myocardial involvement in Duchenne's progressive muscular dystrophy. (author)

Assessment of extent of skin involvement in scleroderma using shear wave elastography

Directory of Open Access Journals (Sweden)

Anupam Wakhlu

2017-01-01

Full Text Available Introduction: Scleroderma (systemic sclerosis [SSc] is a rare autoimmune disease which manifests as fibrosis in the skin and other internal organs. Conventionally, the modified Rodnan skin score (MRSS has been used to quantify the extent of skin fibrosis (resulting in skin tightness in SSc. This technique, although widely validated, is limited by the requirement of a trained, experienced assessor. Recent literature suggests that utilization of the objective ultrasound-based assessment of skin fibrosis utilizing shear wave elastography (SWE may be a more robust technique to detect early skin tightness in SSc. Methods: We evaluated the use of SWE (assessed by an experienced radiologist in 24 patients with SSc compared with 16 healthy controls. Results: Our patients were predominantly females, with median disease duration of 1.5 years and median MRSS of 17. There was minimal intraobserver variation in the assessment of SWE. Patients with SSc had higher SWE values (mean elasticity [Emean] compared to healthy controls at most assessed sites for the MRSS. The Emeancorrelated significantly at all sites with the MRSS scores. At the sites where MRSS was scored as 0 (normal, the Emeanin patients with SSc was higher when compared with similarly clinical normal skin in patients with SSc, suggesting potential early involvement of these areas of the skin with fibrosis. Conclusion: SWE is a promising tool to objectively assess skin fibrosis in SSc and may be useful in detecting early, subclinical skin involvement in this disease.

Mechanical properties of bovine cortical bone based on the automated ball indentation technique and graphics processing method.

Science.gov (United States)

Zhang, Airong; Zhang, Song; Bian, Cuirong

2018-02-01

Cortical bone provides the main form of support in humans and other vertebrates against various forces. Thus, capturing its mechanical properties is important. In this study, the mechanical properties of cortical bone were investigated by using automated ball indentation and graphics processing at both the macroscopic and microstructural levels under dry conditions. First, all polished samples were photographed under a metallographic microscope, and the area ratio of the circumferential lamellae and osteons was calculated through the graphics processing method. Second, fully-computer-controlled automated ball indentation (ABI) tests were performed to explore the micro-mechanical properties of the cortical bone at room temperature and a constant indenter speed. The indentation defects were examined with a scanning electron microscope. Finally, the macroscopic mechanical properties of the cortical bone were estimated with the graphics processing method and mixture rule. Combining ABI and graphics processing proved to be an effective tool to obtaining the mechanical properties of the cortical bone, and the indenter size had a significant effect on the measurement. The methods presented in this paper provide an innovative approach to acquiring the macroscopic mechanical properties of cortical bone in a nondestructive manner. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mechanisms and techniques for public involvement in Pennsylvania

International Nuclear Information System (INIS)

Hunt, M.

1986-01-01

In Pennsylvania, a successful public participation program on the hazardous waste issue was organized in the form of a Hazardous Waste Citizens Advisory Group. This advisory group developed a plan for a disposal facility that included siting criteria for the disposal site, public environment policy, permitting requirements, and Superfund policy. Some of the success of the Pennsylvania program rests with the fact that the governor supports the hazardous waste program. Pennsylvanians have found that the success of a public participation program depends on commitment from the top leadership in the state. This top leadership must seriously consider public recommendations on hazardous waste disposal and must encourage consistency in the public participation program statewide. Public participation must not be confused with public relations. Public relations reaches only in an outward direction. Public participation is a two-way street. It was found that there is more support for a public participation program if the public develops the criteria for the program

TA3 - Dosimetry and instrumentation supply of the M-Fish technique to the Fish-3 painting technique for analysing translocations: A radiotherapy-treated patient study

International Nuclear Information System (INIS)

Pouzoulet, F.; Roch-Lefevre, S.; Giraudet, A.L.; Vaurijoux, A.; Voisin, P.A.; Buard, V.; Delbos, M.; Voisin, Ph.; Roy, L.; Bourhis, J.

2006-01-01

Purpose: Currently, the chromosome translocation study is the best method to estimate the dose of an old radiation exposure. Fluorescent In Situ Hybridization (F.I.S.H.) technique allows an easy detection of this kind of aberrations. However, as only a few number of chromosomes is usually painted, some bias could skew the result. To evaluate the advantage of using full genome staining (M-F.I.S.H. technique) compared with three chromosomes labelling (F.I.S.H.-3 painting), we compared translocation yields in radiotherapy treated patients. Methods: Chromosome aberration analyses were performed on peripheral blood lymphocyte cultures of two patients treated for a throat cancer by radiotherapy. Blood samples were obtained, before, along the treatment and six or four months later. For each sample, a dicentrics analysis was performed together with translocation analysis either with F.I.S.H.-3 painting or M-F.I.S.H.. Results: By confronting results from the F.I.S.H.-3 painting technique and the M-F.I.S.H. technique, significant differences were revealed. The translocations yield seemed to be stable with the F.I.S.H.-3 painting technique whereas it is not the case with the M-F.I.S.H. technique. This difference in results was explained by the bias induced by F.I.S.H.-3 Painting technique in the visualisation of complex aberrations. Furthermore, we found the presence of a clone bearing a translocation involving a painted chromosome. Conclusions: According to the potential bias of F.I.S.H.-3 painting on translocations study, the M-F.I.S.H. technique should provide more precise and reproducible results. Because of its more difficult implement, it seems hardly applicable to retrospective dosimetry instead of F.I.S.H.-3 painting technique. (authors)