WorldWideScience

Sample records for metal-semiconductor hybrid structures

  1. Giant Geometrically Amplified Piezoresistance in Metal-Semiconductor Hybrid Resistors

    DEFF Research Database (Denmark)

    Hansen, Ole; Reck, Kasper; Thomsen, Erik Vilain

    2008-01-01

    We show that very high geometrically amplified piezoresistance can indeed be obtained in microstructured metal-semiconductor hybrid devices, even significantly higher amplification factors than the factor of approximately 8 demonstrated recently by Rowe and co-workers may be achieved. However, we...

  2. Electronic states of semiconductor-metal-semiconductor quantum-well structures

    Science.gov (United States)

    Huberman, M. L.; Maserjian, J.

    1988-01-01

    Quantum-size effects are calculated in thin layered semiconductor-metal-semiconductor structures using an ideal free-electron model for the metal layer. The results suggest new quantum-well structures having device applications. Structures with sufficiently high-quality interfaces should exhibit effects such as negative differential resistance due to tunneling between allowed states. Similarly, optical detection by intersubband absorption may be possible. Ultrathin metal layers are predicted to behave as high-density dopant sheets.

  3. Femtosecond differential transmission measurements on low temperature GaAs metal-semiconductor-metal structures

    DEFF Research Database (Denmark)

    Keil, Ulrich Dieter Felix; Hvam, Jørn Märcher; Tautz, S.

    1997-01-01

    We report on differential transmission measurements on low temperature grown (LT)-GaAs with and without applied electrical fields at different wavelengths. Electrical fields up to 100 kV/cm can be applied via an interdigitated contact structure to our LT GaAs samples which have been removed from....... The response time of a biased metal-semiconductor-metal detector, therefore, exceeds the carrier life time of the substrate material. (C) 1997 American Institute of Physics....

  4. Hybrid metal-semiconductor cavities for multi-band perfect light absorbers and excellent electric conducting interfaces

    Science.gov (United States)

    Huang, Zhenping; Chen, Jian; Liu, Yi; Tang, Li; Liu, Guiqiang; Liu, Xiaoshan; Liu, Zhengqi

    2017-08-01

    It is desirable for optoelectronic devices to have the capability to simultaneously achieve excellent optical and electric features. Nevertheless, most investigations were performed separately for photon and electron management. In this work, we numerically propose and demonstrate a hybrid metal-semiconductor interface, which offers multi-band perfect light absorption and simultaneously retains the naturally perfect electrical conductivity of a flat metal film. Multi-band anti-reflection and near-unity light absorption is observed in this hybrid metal-semiconductor cavity based absorber (HMSA). Our results show that, the maximal absorption above 97% and the naturally perfect electric conductivity are realizable, suggesting the capability of providing both excellent optical and electric properties. Optical Mie-like resonances in the semiconductor cavities and the hybrid coupling with plasmonic resonances by the metal resonators cooperatively support strong optical field confinement effects, which eventually create the light trapped in the HMSA. These features indicate a platform wherein excellent electrical conducting and multispectral light absorption are designed for potential optoelectronic applications.

  5. Transverse Seebeck and Peltier effect in tilted metal-semiconductor multilayer structures

    International Nuclear Information System (INIS)

    Reitmaier, Christina

    2012-01-01

    Whether in aerospace, automobile industry or in home appliances, thermoelectric effects find use in many areas of technology. This work deals with the investigation of a special form of these effects, the transversal Seebeck- and Peltier effect. Via modelling under variation of the sample parameters the cooling efficiencies, the attainable temperature differences and the Figures of merit are optimised and than suitable samples are produced according to these specifications. With these tilted metal semiconductor multilayer structures consisting of lead and bismuth telluride a transversal Peltier effect is observed. Moreover, the generation of electric power is examined via the transversal Seebeck effect. In tilted Pb-Bi2Te3 multilayers the efficiency is measured with the conversion by heat in electric power and is compared to model calculations. (orig.)

  6. Effective carrier sweepout in a silicon waveguide by a metal-semiconductor-metal structure

    DEFF Research Database (Denmark)

    Ding, Yunhong; Hu, Hao; Ou, Haiyan

    2015-01-01

    We demonstrate effective carrier depletion by metal-semiconductor-metal junctions for a silicon waveguide. Photo-generated carriers are efficiently swept out by applying bias voltages, and a shortest carrier lifetime of only 55 ps is demonstrated.......We demonstrate effective carrier depletion by metal-semiconductor-metal junctions for a silicon waveguide. Photo-generated carriers are efficiently swept out by applying bias voltages, and a shortest carrier lifetime of only 55 ps is demonstrated....

  7. Analysis of the series resistance and interface state densities in metal semiconductor structures

    Energy Technology Data Exchange (ETDEWEB)

    Gueler, G [Department of Physics, Faculty of Education, University of Adiyaman, 02100 Adiyaman (Turkey); Guellue, Oe [Department of Physics, Faculty of Sciences and Arts, Atatuerk University, 25240 Erzurum (Turkey); Karatas, S [Department of Physics, Faculty of Sciences and Arts, University of Kahramanmaras Suetcue Imam, 46100 Kahramanmaras (Turkey); Bakkaloglu, Oe F, E-mail: skaratas@ksu.edu.t [Department of Engineering Physics, Faculty of Engineering Physics, University of Gaziantep, 27310 Gaziantep (Turkey)

    2009-03-01

    The electrical properties of Co/n-Si metal-semiconductor (MS) Schottky structure investigated at room temperature using current-voltage (I-V) characteristics. The characteristic parameters of the structure such as barrier height, ideality factor and series resistance have been determined from the I-V measurements. The values of barrier height obtained from Norde's function were compared with those from Cheung functions, and it was seen that there was a good agreement between barrier heights from both methods. The series resistance values calculated with Cheung's two methods were compared and seen that there was an agreement with each other. However, the values of series resistance obtained from Cheung functions and Norde's functions are not agreeing with each other. Because, Cheung functions are only applied to the non-linear region (high voltage region) of the forward bias I-V characteristics. Furthermore, the energy distribution of interface state density was determined from the forward bias I-V characteristics by taking into account the bias dependence of the effective barrier height. The results show that the presence of thin interfacial layer between the metal and semiconductor.

  8. Evaluating nanoscale ultra-thin metal films by means of lateral photovoltaic effect in metal-semiconductor structure.

    Science.gov (United States)

    Zheng, Diyuan; Yu, Chongqi; Zhang, Qian; Wang, Hui

    2017-12-15

    Nanoscale metal-semiconductor (MS) structure materials occupy an important position in semiconductor and microelectronic field due to their abundant physical phenomena and effects. The thickness of metal films is a critical factor in determining characteristics of MS devices. How to detect or evaluate the metal thickness is always a key issue for realizing high performance MS devices. In this work, we propose a direct surface detection by use of the lateral photovoltaic effect (LPE) in MS structure, which can not only measure nanoscale thickness, but also detect the fluctuation of metal films. This method is based on the fact that the output of lateral photovoltaic voltage (LPV) is closely linked with the metal thickness at the laser spot. We believe this laser-based contact-free detection is a useful supplement to the traditional methods, such as AFM, SEM, TEM or step profiler. This is because these traditional methods are always incapable of directly detecting ultra-thin metal films in MS structure materials.

  9. Metal-Semiconductor Contacts

    Science.gov (United States)

    Pugh, D. I.

    Metal-semiconductor contacts display a range of electrical characteristics from strongly rectifying to ohmic, each having its own applications. The rectifying properties of metal points on metallic sulphides were used extensively as detectors in early radio experiments, while during the second world war the rectifying point contact diode became important as a frequency detector and low level microwave radar detector [1]. Since 1945 the development of metal semiconductor contacts has been stimulated by the intense activity in the field of semiconductor physics and has remained vital in the ohmic connection of semiconductor devices with the outside world. The developments in surface science and the increased use of Schottky barriers in microelectronics has lead to much research with the aim of obtaining a full understanding of the physics of barrier formation and of current transport across the metal-semiconductor interface. Large gain spin electronic devices are possible with appropriate designs by incorporating ferromagnetic layers with semiconductors such as silicon [2]. This inevitably leads to metal-semiconductor contacts, and the impact of such junctions on the device must be considered. In this section we aim to look simply at the physical models that can be used to understand the electrical properties that can arise from these contacts, and then briefly discuss how deviations of these models can occur in practical junctions.

  10. Metal semiconductor contacts and devices

    CERN Document Server

    Cohen, Simon S; Einspruch, Norman G

    1986-01-01

    VLSI Electronics Microstructure Science, Volume 13: Metal-Semiconductor Contacts and Devices presents the physics, technology, and applications of metal-semiconductor barriers in digital integrated circuits. The emphasis is placed on the interplay among the theory, processing, and characterization techniques in the development of practical metal-semiconductor contacts and devices.This volume contains chapters that are devoted to the discussion of the physics of metal-semiconductor interfaces and its basic phenomena; fabrication procedures; and interface characterization techniques, particularl

  11. Ion electromigration in CdTe Schottky metal-semiconductor-metal structure

    Czech Academy of Sciences Publication Activity Database

    Elhadidy, Hassan; Grill, R.; Franc, J.; Sik, O.; Moravec, P.; Schneeweiss, Oldřich

    2015-01-01

    Roč. 278, OCT (2015), s. 20-25 ISSN 0167-2738 R&D Projects: GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68081723 Keywords : M-S-M Structure * Electromigration * Au/CdTe interface * I-V characteristics * Current transients * Diffusion coefficient Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.380, year: 2015

  12. Transverse Seebeck and Peltier effect in tilted metal-semiconductor multilayer structures; Transversaler Seebeck- und Peltier-Effekt in verkippten Metall-Halbleiter-Multilagenstrukturen

    Energy Technology Data Exchange (ETDEWEB)

    Reitmaier, Christina

    2012-07-01

    Whether in aerospace, automobile industry or in home appliances, thermoelectric effects find use in many areas of technology. This work deals with the investigation of a special form of these effects, the transversal Seebeck- and Peltier effect. Via modelling under variation of the sample parameters the cooling efficiencies, the attainable temperature differences and the Figures of merit are optimised and than suitable samples are produced according to these specifications. With these tilted metal semiconductor multilayer structures consisting of lead and bismuth telluride a transversal Peltier effect is observed. Moreover, the generation of electric power is examined via the transversal Seebeck effect. In tilted Pb-Bi2Te3 multilayers the efficiency is measured with the conversion by heat in electric power and is compared to model calculations. (orig.)

  13. Plasmonic effects in metal-semiconductor nanostructures

    CERN Document Server

    Toropov, Alexey A

    2015-01-01

    Metal-semiconductor nanostructures represent an important new class of materials employed in designing advanced optoelectronic and nanophotonic devices, such as plasmonic nanolasers, plasmon-enhanced light-emitting diodes and solar cells, plasmonic emitters of single photons, and quantum devices operating in infrared and terahertz domains. The combination of surface plasmon resonances in conducting structures, providing strong concentration of an electromagnetic optical field nearby, with sharp optical resonances in semiconductors, which are highly sensitive to external electromagnetic fields, creates a platform to control light on the nanoscale. The design of the composite metal-semiconductor system imposes the consideration of both the plasmonic resonances in metal and the optical transitions in semiconductors - a key issue being their resonant interaction providing a coupling regime. In this book the reader will find descriptions of electrodynamics of conducting structures, quantum physics of semiconducto...

  14. Silicon metal-semiconductor-metal photodetector

    Science.gov (United States)

    Brueck, Steven R. J.; Myers, David R.; Sharma, Ashwani K.

    1995-01-01

    Silicon MSM photodiodes sensitive to radiation in the visible to near infrared spectral range are produced by altering the absorption characteristics of crystalline Si by ion implantation. The implantation produces a defected region below the surface of the silicon with the highest concentration of defects at its base which acts to reduce the contribution of charge carriers formed below the defected layer. The charge carriers generated by the radiation in the upper regions of the defected layer are very quickly collected between biased Schottky barrier electrodes which form a metal-semiconductor-metal structure for the photodiode.

  15. Specific Contact Resistance Measurements of Metal Semiconductor-Junctions

    NARCIS (Netherlands)

    Stavitski, N.; van Dal, M.J.H.; Wolters, Robertus A.M.; Kovalgin, Alexeij Y.; Schmitz, Jurriaan

    2006-01-01

    Our research comprises the manufacturing of test structures to characterize the metal-semiconductor junctions with a number of techniques and materials. An extensive subsequent physical and electrical testing of the junctions is carried out. We present our first results on specific

  16. Carrier dynamics analysis in metal-semiconductor-metal device for mid-IR silicon photonics

    DEFF Research Database (Denmark)

    Hui, Alvin Tak Lok; Ding, Yunhong; Hu, Hao

    2017-01-01

    A modelling platform for active carrier removal based on metal-semiconductor-metal structure is reported on analysis of carrier dynamics. The analysis reveals electric current hot spots exist in geometric singularities and curly trajectory of carriers should be considered when accurately estimati...... the effective carrier lifetime....

  17. Analysis of interface states and series resistance for Al/PVA:n-CdS nanocomposite metal-semiconductor and metal-insulator-semiconductor diode structures

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Mamta; Tripathi, S.K. [Panjab University, Centre of Advanced Study in Physics, Department of Physics, Chandigarh (India)

    2013-11-15

    This paper presents the fabrication and characterization of Al/PVA:n-CdS (MS) and Al/Al{sub 2}O{sub 3}/PVA:n-CdS (MIS) diode. The effects of interfacial insulator layer, interface states (N{sub ss}) and series resistance (R{sub s}) on the electrical characteristics of Al/PVA:n-CdS structures have been investigated using forward and reverse bias I-V, C-V, and G/w-V characteristics at room temperature. Al/PVA:n-CdS diode is fabricated with and without insulator Al{sub 2}O{sub 3} layer to explain the effect of insulator layer on main electrical parameters. The values of the ideality factor (n), series resistance (R{sub s}) and barrier height ({phi} {sub b}) are calculated from ln(I) vs. V plots, by the Cheung and Norde methods. The energy density distribution profile of the interface states is obtained from the forward bias I-V data by taking into account the bias dependence ideality factor (n(V)) and effective barrier height ({phi} {sub e}) for MS and MIS diode. The N{sub ss} values increase from mid-gap energy of CdS to the bottom of the conductance band edge for both MS and MIS diode. (orig.)

  18. Synthesis of agarose-metal/semiconductor nanoparticles having ...

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Chemical Sciences; Volume 120; Issue 6. Synthesis of agarose-metal/semiconductor nanoparticles having superior bacteriocidal activity and their simple conversion to metal-carbon composites. K K R Datta B Srinivasan H Balaram M Eswaramoorthy. Volume 120 Issue 6 November 2008 pp 579- ...

  19. Synthesis of agarose-metal/semiconductor nanoparticles having ...

    Indian Academy of Sciences (India)

    Agarose, a naturally occurring biopolymer is used for the stabilization of metal, semiconductor nanoparticles. Ag and Cu nanoparticles stabilized in agarose matrix show excellent antibacterial activity against E. coli bacteria. The well dispersed metal nanoparticles within the agarose composite films can be readily converted ...

  20. Shottky-barrier formation. Abrupt metal-semiconductor junctions

    Energy Technology Data Exchange (ETDEWEB)

    Guines, F.; Sanchez-Dehesa, J.; Flores, F.

    1983-02-01

    In this paper a realistic self-consistent calculation of an abrupt metal-semiconductor junction is presented by means of a tight-binding approach. A specific Si-Ag junction has been considered, and the charge neutrality level as well as the barrier height have been determined in good agreement with experiments. For a general junction it is shown that the interface properties depend essentially on the characteristics of the first metal layer and its interaction with the semiconductor.

  1. Organic modification of metal / semiconductor Schottky contacts

    Energy Technology Data Exchange (ETDEWEB)

    Mendez Pinzon, H.A.

    2006-07-10

    In the present work a Metal / organic / inorganic semiconductor hybrid heterostructure (Ag / DiMe-PTCDI / GaAs) was built under UHV conditions and characterised in situ. The aim was to investigate the influence of the organic layer in the surface properties of GaAs(100) and in the electrical response of organic-modified Ag / GaAs Schottky diodes. The device was tested by combining surface-sensitive techniques (Photoemission spectroscopy and NEXAFS) with electrical measurements (current-voltage, capacitance-voltage, impedance and charge transient spectroscopies). Core level examination by PES confirms removal of native oxide layers on sulphur passivated (S-GaAs) and hydrogen plasma treated GaAs(100) (H+GaAs) surfaces. Additional deposition of ultrathin layers of DiMe-PTCDI may lead to a reduction of the surface defects density and thereby to an improvement of the electronic properties of GaAs. The energy level alignment through the heterostructure was deduced by combining UPS and I-V measurements. This allows fitting of the I-V characteristics with electron as majority carriers injected over a barrier by thermionic emission as a primary event. For thin organic layers (below 8 nm thickness) several techniques (UPS, I-V, C-V, QTS and AFM) show non homogeneous layer growth, leading to formation of voids. The coverage of the H+GaAs substrate as a function of the nominal thickness of DiMe-PTCDI was assessed via C-V measurements assuming a voltage independent capacitance of the organic layer. The frequency response of the device was evaluated through C-V and impedance measurements in the range 1 kHz-1 MHz. The almost independent behaviour of the capacitance in the measured frequency range confirmed the assumption of a near geometrical capacitor, which was used for modelling the impedance with an equivalent circuit of seven components. From there it was found a predominance of the space charge region impedance, so that A.C. conduction can only takes place through the

  2. The Interfacial Thermal Conductance of Epitaxial Metal-Semiconductor Interfaces

    Science.gov (United States)

    Ye, Ning

    Understanding heat transport at nanometer and sub-nanometer lengthscales is critical to solving a wide range of technological challenges related to thermal management and energy conversion. In particular, finite Interfacial Thermal Conductance (ITC) often dominates transport whenever multiple interfaces are closely spaced together or when heat originates from sources that are highly confined by interfaces. Examples of the former include superlattices, thin films, quantum cascade lasers, and high density nanocomposites. Examples of the latter include FinFET transistors, phase-change memory, and the plasmonic transducer of a heat-assisted magnetic recording head. An understanding of the physics of such interfaces is still lacking, in part because experimental investigations to-date have not bothered to carefully control the structure of interfaces studied, and also because the most advanced theories have not been compared to the most robust experimental data. This thesis aims to resolve this by investigating ITC between a range of clean and structurally well-characterized metal-semiconductor interfaces using the Time-Domain Thermoreflectance (TDTR) experimental technique, and by providing theoretical/computational comparisons to the experimental data where possible. By studying the interfaces between a variety of materials systems, each with unique aspects to their tunability, I have been able to answer a number of outstanding questions regarding the importance of interfacial quality (epitaxial/non-epitaxial interfaces), semiconductor doping, matching of acoustic and optical phonon band structure, and the role of phonon transport mechanisms apart from direct elastic transmission on ITC. In particular, we are able to comment on the suitability of the diffuse mismatch model (DMM) to describe the transport across epitaxial interfaces. To accomplish this goal, I studied interfacial thermal transport across CoSi2, TiSi2, NiSi and PtSi - Si(100) and Si(111), (silicides

  3. Hybrid Tower, Designing Soft Structures

    DEFF Research Database (Denmark)

    Ramsgaard Thomsen, Mette; Tamke, Martin; Holden Deleuran, Anders

    2015-01-01

    predictions about the inherent interdependency and material dependent performance of the hybrid structure and (2) the inter-scalar design strategies for specification and fabrication. The first investigation focuses on the design pipelines developed between the implementation of realtime physics......This paper presents the research project Hybrid Tower, an interdisciplinary collaboration between CITA—Centre for IT and Architecture, KET—Department for Structural Design and Technology, Fibrenamics, Universidade do Minho Guimarães, AFF a. ferreira & filhos, sa, Caldas de Vizela, Portugal...... and Essener Labor für Leichte Flächentragwerke, Universität Duisburg-Essen. Hybrid Tower is a hybrid structural system combining bending active compression members and tensile members for architectural design. The paper presents two central investigations: (1) the creation of new design methods that embed...

  4. Metal-semiconductor interface in extreme temperature conditions

    International Nuclear Information System (INIS)

    Bulat, L.P.; Erofeeva, I.A.; Vorobiev, Yu.V.; Gonzalez-Hernandez, J.

    2008-01-01

    We present an investigation of electrons' and phonons' temperatures in the volume of a semiconductor (or metal) sample and at the interface between metal and semiconductor. Two types of mismatch between electrons' and phonons' temperatures take place: at metal-semiconductor interfaces and in the volume of the sample. The temperature mismatch leads to nonlinear terms in expressions for heat and electricity transport. The nonlinear effects should be taken into consideration in the study of electrical and heat transport in composites and in electronic chips

  5. Hybrid Simulation of Composite Structures

    DEFF Research Database (Denmark)

    Høgh, Jacob Herold

    Hybrid simulation is a substructural method combining a numerical simulation with a physical experiment. A structure is thereby simulated under the assumption that a substructure’s response is well known and easily modelled while a given substructure is studied more accurately in a physical...... of freedom. In this dissertation the main focus is to develop hybrid simulation for composite structures e.g. wind turbine blades where the boundary between the numerical model and the physical experiment is continues i.e. in principal infinite amount of degrees of freedom. This highly complicates...... the transfer system and the control and monitoring techniques in the shared boundary is therefore a key issue in this type of hybrid simulation. During the research, hybrid simulation platforms have been programmed capable of running on different time scales with advanced control and monitoring techniques...

  6. A 75 GHz silicon metal-semiconductor-metal Schottky photodiode

    International Nuclear Information System (INIS)

    Alexandrou, S.; Wang, C.; Hsiang, T.Y.; Liu, M.Y.; Chou, S.Y.

    1993-01-01

    The ultrafast characteristics of crystalline-silicon metal-semiconductor-metal (MSM) photodiodes with 300 nm finger width and spacing were measured with a subpicosecond electro-optic sampling system. Electrical responses with full width at half maximum as short as 5.5 and 11 ps, at corresponding 3 dB bandwidths of 75 and 38 GHz, were generated by violet and red photons, respectively. The difference is attributed to the photon penetration depth which is much larger than the diode finger spacing at red, but smaller at violet. Light-intensity dependence was also examined at different wavelengths, indicating a linear relation and a higher sensitivity in the violet. These results not only demonstrated the fastest silicon photodetector reported to date, but also pinpointed the dominant speed-limiting factor of silicon MSM photodiodes. A configuration is suggested to improve the speed of these detectors at long wavelengths

  7. Metal-semiconductor transition of graphene nanoribbons with different addends

    Science.gov (United States)

    Zhang, X. W.; Dai, B.; Liu, J. S.; Yang, G. W.

    2012-02-01

    Using a LCAO method, which is based on spinless sp3 scheme, we have studied the electronic properties of graphene nanoribbons with zigzag edges (ZGNRs) terminated partially by methylene groups. Metal-semiconductor transition is proved when the H atoms at both sides of ZGNRs are partially substituted by methylene groups. Furthermore, when one-third of H atoms are substituted and the distribution of methylenes is symmetric, the band gap comes to about 0.59 eV, which is the widest energy gap in this work. Otherwise, when the addends at both sides are of asymmetric distribution, a band gap of only 0.21 eV is obtained. These results suggest that the addends at the edge of ZGNRs play an important role in modifying the electronic properties.

  8. Metal-semiconductor transition of graphene nanoribbons with different addends

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X.W., E-mail: xiaoweizhang@swust.edu.cn [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China); Dai, B; Liu, J.S. [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China); Yang, G.W. [State Key Laboratory of Optoelectronic Materials and Technologies, Institute of Optoelectronic and Functional Composite Materials, School of Physics Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China)

    2012-02-15

    Using a LCAO method, which is based on spinless sp{sup 3} scheme, we have studied the electronic properties of graphene nanoribbons with zigzag edges (ZGNRs) terminated partially by methylene groups. Metal-semiconductor transition is proved when the H atoms at both sides of ZGNRs are partially substituted by methylene groups. Furthermore, when one-third of H atoms are substituted and the distribution of methylenes is symmetric, the band gap comes to about 0.59 eV, which is the widest energy gap in this work. Otherwise, when the addends at both sides are of asymmetric distribution, a band gap of only 0.21 eV is obtained. These results suggest that the addends at the edge of ZGNRs play an important role in modifying the electronic properties.

  9. Designing Selectivity in Metal-Semiconductor Nanocrystals: Synthesis, Characterization, and Self-Assembly

    Science.gov (United States)

    Pavlopoulos, Nicholas George

    This dissertation contains six chapters detailing recent advances that have been made in the synthesis and characterization of metal-semiconductor hybrid nanocrystals (HNCs), and the applications of these materials. Primarily focused on the synthesis of well-defined II-VI semiconductor nanorod (NR) and tetrapod (TP) based constructs of interest for photocatalytic and solar energy applications, the research described herein discusses progress towards the realization of key design rules for the synthesis of functional semiconductor nanocrystals (NCs). As such, a blend of novel synthesis, advanced characterization, and direct application of heterostructured nanoparticles are presented. The first chapter is a review summarizing the design, synthesis, properties, and applications of multicomponent nanomaterials composed of disparate semiconductor and metal domains. By coupling two compositionally distinct materials onto a single nanocrystal, synergistic properties can arise that are not present in the isolated components, ranging from self-assembly to photocatalysis. For semiconductor nanomaterials, this was first realized in the ability to tune nanomaterial dimensions from 0-D quantum dot (QD) structures to cylindrical (NR) and branched (TP) structures by exploitation of advanced colloidal synthesis techniques and understandings of NC facet reactivities. The second chapter is focused on the synthesis and characterization of well-defined CdSe-seeded-CdS (CdSe CdS) NR systems synthesized by overcoating of wurtzite (W) CdSe quantum dots with W-CdS shells. 1-dimensional NRs have been interesting constructs for applications such as solar concentrators, optical gains, and photocatalysis. Through synthetic control over CdSe CdS NR systems, materials with small and large CdSe seeds were prepared, and for each seed size, multiple NR lengths were prepared. Through transient absorption studies, it was found that band alignment did not affect the efficiency of charge localization

  10. Electronic properties of semiconductor surfaces and metal/semiconductor interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Tallarida, M.

    2005-05-15

    This thesis reports investigations of the electronic properties of a semiconductor surface (silicon carbide), a reactive metal/semiconductor interface (manganese/silicon) and a non-reactive metal/semiconductor interface (aluminum-magnesium alloy/silicon). The (2 x 1) reconstruction of the 6H-SiC(0001) surface has been obtained by cleaving the sample along the (0001) direction. This reconstruction has not been observed up to now for this compound, and has been compared with those of similar elemental semiconductors of the fourth group of the periodic table. This comparison has been carried out by making use of photoemission spectroscopy, analyzing the core level shifts of both Si 2p and C 1s core levels in terms of charge transfer between atoms of both elements and in different chemical environments. From this comparison, a difference between the reconstruction on the Si-terminated and the C-terminated surface was established, due to the ionic nature of the Si-C bond. The growth of manganese films on Si(111) in the 1-5 ML thickness range has been studied by means of LEED, STM and photoemission spectroscopy. By the complementary use of these surface science techniques, two different phases have been observed for two thickness regimes (<1 ML and >1 ML), which exhibit a different electronic character. The two reconstructions, the (1 x 1)-phase and the ({radical}3 x {radical}3)R30 -phase, are due to silicide formation, as observed in core level spectroscopy. The growth proceeds via island formation in the monolayer regime, while the thicker films show flat layers interrupted by deep holes. On the basis of STM investigations, this growth mode has been attributed to strain due to lattice mismatch between the substrate and the silicide. Co-deposition of Al and Mg onto a Si(111) substrate at low temperature (100K) resulted in the formation of thin alloy films. By varying the relative content of both elements, the thin films exhibited different electronic properties

  11. Visible light sensitive cupric oxide metal-semiconductor-metal photodetectors

    Science.gov (United States)

    Raghavendra, P. V.; Bhat, J. S.; Deshpande, N. G.

    2018-01-01

    The visible light response of Ag-CuO-Ag metal-semiconductor-metal (MSM) photodetector is presented. Electron beam deposited CuO thin films consisted of tightly packed nanocrystallites in monoclinic phase. The observed red-shifts in indirect band-gap from 1.09 eV to 0.99 eV and direct band-gap from 2.92 eV to 2.87 eV, with annealing temperature, is attributed to the weak quantum confinement effect. CuO thin films annealed at 500 °C have a p-type conductivity of 4.33 × 10-2 (ohm-cm)-1 and mobility of 13.2 cm2/V-s. Significant responsivities of 0.33 mA/W and 0.59 mA/W for blue and red lights, respectively, in Ag-CuO-Ag photodetector are illustrative for using it as visible light sensor.

  12. Metal-semiconductor Schottky barrier junctions and their applications

    CERN Document Server

    1984-01-01

    The present-day semiconductor technology would be inconceivable without extensive use of Schottky barrier junctions. In spite of an excellent book by Professor E.H. Rhoderick (1978) dealing with the basic principles of metal­ semiconductor contacts and a few recent review articles, the need for a monograph on "Metal-Semiconductor Schottky Barrier Junctions and Their Applications" has long been felt by students, researchers, and technologists. It was in this context that the idea of publishing such a monograph by Mr. Ellis H. Rosenberg, Senior Editor, Plenum Publishing Corporation, was considered very timely. Due to the numerous and varied applications of Schottky barrier junctions, the task of bringing it out, however, looked difficult in the beginning. After discussions at various levels, it was deemed appropriate to include only those typical applications which were extremely rich in R&D and still posed many challenges so that it could be brought out in the stipulated time frame. Keeping in view the la...

  13. Plasmon-Mediated Solar Energy Conversion via Photocatalysis in Noble Metal/Semiconductor Composites.

    Science.gov (United States)

    Wang, Mengye; Ye, Meidan; Iocozzia, James; Lin, Changjian; Lin, Zhiqun

    2016-06-01

    Plasmonics has remained a prominent and growing field over the past several decades. The coupling of various chemical and photo phenomenon has sparked considerable interest in plasmon-mediated photocatalysis. Given plasmonic photocatalysis has only been developed for a relatively short period, considerable progress has been made in improving the absorption across the full solar spectrum and the efficiency of photo-generated charge carrier separation. With recent advances in fundamental (i.e., mechanisms) and experimental studies (i.e., the influence of size, geometry, surrounding dielectric field, etc.) on plasmon-mediated photocatalysis, the rational design and synthesis of metal/semiconductor hybrid nanostructure photocatalysts has been realized. This review seeks to highlight the recent impressive developments in plasmon-mediated photocatalytic mechanisms (i.e., Schottky junction, direct electron transfer, enhanced local electric field, plasmon resonant energy transfer, and scattering and heating effects), summarize a set of factors (i.e., size, geometry, dielectric environment, loading amount and composition of plasmonic metal, and nanostructure and properties of semiconductors) that largely affect plasmonic photocatalysis, and finally conclude with a perspective on future directions within this rich field of research.

  14. Plasmon‐Mediated Solar Energy Conversion via Photocatalysis in Noble Metal/Semiconductor Composites

    Science.gov (United States)

    Wang, Mengye; Ye, Meidan; Iocozzia, James

    2016-01-01

    Plasmonics has remained a prominent and growing field over the past several decades. The coupling of various chemical and photo phenomenon has sparked considerable interest in plasmon‐mediated photocatalysis. Given plasmonic photocatalysis has only been developed for a relatively short period, considerable progress has been made in improving the absorption across the full solar spectrum and the efficiency of photo‐generated charge carrier separation. With recent advances in fundamental (i.e., mechanisms) and experimental studies (i.e., the influence of size, geometry, surrounding dielectric field, etc.) on plasmon‐mediated photocatalysis, the rational design and synthesis of metal/semiconductor hybrid nanostructure photocatalysts has been realized. This review seeks to highlight the recent impressive developments in plasmon‐mediated photocatalytic mechanisms (i.e., Schottky junction, direct electron transfer, enhanced local electric field, plasmon resonant energy transfer, and scattering and heating effects), summarize a set of factors (i.e., size, geometry, dielectric environment, loading amount and composition of plasmonic metal, and nanostructure and properties of semiconductors) that largely affect plasmonic photocatalysis, and finally conclude with a perspective on future directions within this rich field of research. PMID:27818901

  15. Study of low dimensional SiGe island on Si for potential visible Metal-Semiconductor-Metal photodetector

    Science.gov (United States)

    Rahim, Alhan Farhanah Abd; Zainal Badri, Nur'Amirah; Radzali, Rosfariza; Mahmood, Ainorkhilah

    2017-11-01

    In this paper, an investigation of design and simulation of silicon germanium (SiGe) islands on silicon (Si) was presented for potential visible metal semiconductor metal (MSM) photodetector. The characterization of the performances in term of the structural, optical and electrical properties of the structures was analyzed from the simulation results. The project involves simulation using SILVACO Technology Computer Aided Design (TCAD) tools. The different structures of the silicon germanium (SiGe) island on silicon substrate were created, which were large SiGe, small SiGe, combination SiGe and bulk Ge. All the structures were tested for potential Metal Semiconductor Metal (MSM) photodetector. The extracted data such as current versus voltage characteristic, current gain and spectral response were obtained using ATLAS SILVACO tools. The performance of SiGe island structures and bulk Ge on Si substrate as (MSM) photodetector was evaluated by photo and dark current-voltage (I-V) characteristics. It was found that SiGe islands exhibited higher energy band gap compared to bulk Ge. The SiGe islands current-voltage characteristics showed improved current gain compared to bulk Ge. Specifically the enhancement of the islands gain was contributed by the enhanced photo currents and lower dark currents. The spectral responses of the SiGe islands showed peak response at 590 nm (yellow) which is at the visible wavelength. This shows the feasibility of the SiGe islands to be utilized for visible photodetections.

  16. Study of low dimensional SiGe island on Si for potential visible Metal-Semiconductor-Metal photodetector

    Directory of Open Access Journals (Sweden)

    Abd Rahim Alhan Farhanah

    2017-01-01

    Full Text Available In this paper, an investigation of design and simulation of silicon germanium (SiGe islands on silicon (Si was presented for potential visible metal semiconductor metal (MSM photodetector. The characterization of the performances in term of the structural, optical and electrical properties of the structures was analyzed from the simulation results. The project involves simulation using SILVACO Technology Computer Aided Design (TCAD tools. The different structures of the silicon germanium (SiGe island on silicon substrate were created, which were large SiGe, small SiGe, combination SiGe and bulk Ge. All the structures were tested for potential Metal Semiconductor Metal (MSM photodetector. The extracted data such as current versus voltage characteristic, current gain and spectral response were obtained using ATLAS SILVACO tools. The performance of SiGe island structures and bulk Ge on Si substrate as (MSM photodetector was evaluated by photo and dark current-voltage (I-V characteristics. It was found that SiGe islands exhibited higher energy band gap compared to bulk Ge. The SiGe islands current-voltage characteristics showed improved current gain compared to bulk Ge. Specifically the enhancement of the islands gain was contributed by the enhanced photo currents and lower dark currents. The spectral responses of the SiGe islands showed peak response at 590 nm (yellow which is at the visible wavelength. This shows the feasibility of the SiGe islands to be utilized for visible photodetections.

  17. Spin-transport-phenomena in metals, semiconductors, and insulators

    Energy Technology Data Exchange (ETDEWEB)

    Althammer, Matthias Klaus

    2012-07-19

    Assuming that one could deterministically inject, transport, manipulate, store and detect spin information in solid state devices, the well-established concepts of charge-based electronics could be transferred to the spin realm. This thesis explores the injection, transport, manipulation and storage of spin information in metallic conductors, semiconductors, as well as electrical insulators. On the one hand, we explore the spin-dependent properties of semiconducting zinc oxide thin films deposited via laser-molecular beam epitaxy (laser-MBE). After demonstrating that the zinc oxide films fabricated during this thesis have excellent structural, electrical, and optical properties, we investigate the spin-related properties by optical pump/probe, electrical injection/optical detection, and all electrical spin valve-based experiments. The two key results from these experiments are: (i) Long-lived spin states with spin dephasing times of 10 ns at 10 K related to donor bound excitons can be optically addressed. (ii) The spin dephasing times relevant for electrical transport-based experiments are {<=} 2 ns at 10 K and are correlated with structural quality. On the other hand we focus on two topics of current scientific interest: the comparison of the magnetoresistance to the magnetothermopower of conducting ferromagnets, and the investigation of pure spin currents generated in ferromagnetic insulator/normal metal hybrid structures. We investigate the magnetoresistance and magnetothermopower of gallium manganese arsenide and Heusler thin films as a function of external magnetic field orientation. Using a series expansion of the resistivity and Seebeck tensors and the inherent symmetry of the sample's crystal structure, we show that a full quantitative extraction of the transport tensors from such experiments is possible. Regarding the spin currents in ferromagnetic insulator/normal metal hybrid structures we studied the spin mixing conductance in yttrium iron garnet

  18. Interface engineering in inorganic hybrid structures towards improved photocatalysis (Conference Presentation)

    Science.gov (United States)

    Xiong, Yujie

    2016-10-01

    Designing new photocatalytic materials for improving photoconversion efficiency is a promising route to alleviate the steadily worsening environmental issues and energy crisis. Despite the invention of a large number of catalytic materials with well-defined structures, their overall efficiency in photocatalysis is still quite limited as the three key steps - light harvesting, charge generation and separation, and charge transfer to surface for redox reactions - have not been substantially improved. To improve each step in the complex process, there is a major trend to develop materials based on inorganic hybrid structures. In this case, interface engineering holds the promise for boosting the overall efficiency, given the key roles of interface structures in charge and energy transfer. In this talk, I will demonstrate several different approaches to designing inorganic hybrid structures with improved photocatalytic performance via interface engineering. The typical demonstrations include semiconductor-plasmonics systems for broad-spectrum light harvesting, metal-semiconductor interfaces for improved charge separation, semiconductor-MOF (metal-organic framework) configurations for activated surface reactions. It is anticipated that this series of works open a new window to rationally designing inorganic hybrid materials for photo-induced applications. References: (1) Bai, S.; Yang, L.; Wang, C.; Lin, Y.; Lu, J.; Jiang, J. and Xiong, Y.*, Angew. Chem. Int. Ed. 54, 14810-14814 (2015). (2) Bai, S.; Jiang, J.; Zhang, Q. and Xiong, Y.*, Chem. Soc. Rev. 44, 2893-2939 (2015). (3) Bai, S.; Li, X.; Kong, Q.; Long, R.; Wang, C.; Jiang, J. and Xiong, Y.*, Adv. Mater. 27, 3444-3452 (2015). (4) Bai, S.; Ge, J.; Wang, L.; Gong, M.; Deng, M.; Kong, Q.; Song, L.; Jiang, J.;* Zhang, Q.;* Luo, Y.; Xie, Y. and Xiong, Y.*, Adv. Mater. 26, 5689-5695 (2014). (5) Li, R.; Hu, J.; Deng, M.; Wang, H.; Wang, X.; Hu, Y.; Jiang, H. L.; Jiang, J.;* Zhang, Q.;* Xie, Y. and Xiong, Y.*, Adv. Mater

  19. Biomolecular detection using a metal semiconductor field effect transistor

    Science.gov (United States)

    Estephan, Elias; Saab, Marie-Belle; Buzatu, Petre; Aulombard, Roger; Cuisinier, Frédéric J. G.; Gergely, Csilla; Cloitre, Thierry

    2010-04-01

    In this work, our attention was drawn towards developing affinity-based electrical biosensors, using a MESFET (Metal Semiconductor Field Effect Transistor). Semiconductor (SC) surfaces must be prepared before the incubations with biomolecules. The peptides route was adapted to exceed and bypass the limits revealed by other types of surface modification due to the unwanted unspecific interactions. As these peptides reveal specific recognition of materials, then controlled functionalization can be achieved. Peptides were produced by phage display technology using a library of M13 bacteriophage. After several rounds of bio-panning, the phages presenting affinities for GaAs SC were isolated; the DNA of these specific phages were sequenced, and the peptide with the highest affinity was synthesized and biotinylated. To explore the possibility of electrical detection, the MESFET fabricated with the GaAs SC were used to detect the streptavidin via the biotinylated peptide in the presence of the bovine Serum Albumin. After each surface modification step, the IDS (current between the drain and the source) of the transistor was measured and a decrease in the intensity was detected. Furthermore, fluorescent microscopy was used in order to prove the specificity of this peptide and the specific localisation of biomolecules. In conclusion, the feasibility of producing an electrical biosensor using a MESFET has been demonstrated. Controlled placement, specific localization and detection of biomolecules on a MESFET transistor were achieved without covering the drain and the source. This method of functionalization and detection can be of great utility for biosensing application opening a new way for developing bioFETs (Biomolecular Field-Effect Transistor).

  20. The Effect of the Electron Tunneling on the Photoelectric Hot Electrons Generation in Metallic-Semiconductor Nanostructures

    Science.gov (United States)

    Elsharif, Asma M.

    2018-01-01

    Semiconductor photonic crystals (MSPhC) were used to convert solar energy into hot electrons. An experimental model was designed by using metallic semiconductor photonic crystals (MSPhC). The designed MSPhC is based on TiO2/Au schottky contact. The model has similar nanocavity structure for broad gold absorption, but the materials on top of the cavity were changed to a metal and a semiconductor in order to collect the hot electrons. Detailed design steps and characterization have shown a broadband sub-bandgap photoresponse at a wavelength of 590 nm. This is due to the surface plasmon absorption by the wafer-scale Au/TiO2 metallic-semiconductor photonic crystal. Analytical calculation of the hot electron transport from the Au thin layer to the TiO2 conduction band is discussed. This theoretical study is based on the quantum tunneling effect. The photo generation of the hot electrons was undertaken at different wavelengths in Au absorber followed by tunneling through a schottky barrier into a TiO2 collector. The presence of a tunnel current from the absorber to the collector under illumination, offers a method to extract carriers from a hot-electron distribution at few bias voltages is presented in this study. The effects of doping different concentrations of the semiconductor on the evolution of the current characteristics were also investigated and discussed. The electrical characteristics were found to be sensitive to any change in the thickness of the barrier.

  1. Barrier height enhancement of metal/semiconductor contact by an enzyme biofilm interlayer

    Science.gov (United States)

    Ocak, Yusuf Selim; Gul Guven, Reyhan; Tombak, Ahmet; Kilicoglu, Tahsin; Guven, Kemal; Dogru, Mehmet

    2013-06-01

    A metal/interlayer/semiconductor (Al/enzyme/p-Si) MIS device was fabricated using α-amylase enzyme as a thin biofilm interlayer. It was observed that the device showed an excellent rectifying behavior and the barrier height value of 0.78 eV for Al/α-amylase/p-Si was meaningfully larger than the one of 0.58 eV for conventional Al/p-Si metal/semiconductor (MS) contact. Enhancement of the interfacial potential barrier of Al/p-Si MS diode was realized using enzyme interlayer by influencing the space charge region of Si semiconductor. The electrical properties of the structure were executed by the help of current-voltage and capacitance-voltage measurements. The photovoltaic properties of the structure were executed under a solar simulator with AM1.5 global filter between 40 and 100 mW/cm2 illumination conditions. It was also reported that the α-amylase enzyme produced from Bacillus licheniformis had a 3.65 eV band gap value obtained from optical method.

  2. A step towards molecular electronics. The ferrocene molecule on a metal-semiconductor system

    Energy Technology Data Exchange (ETDEWEB)

    Schmeidel, Jedrzej Piotr

    2012-05-14

    In the first part, the domain walls on Ag {radical}(3) x {radical}(3) are investigated and structural and electronic model are introduced and discussed. Furthermore, the temperature dependence is investigated, showing the Peierls-type transition along the domain wall chain. In the second part, the high resolution STM data of the local adsorption geometry of FDT on Ag {radical}(3)< x {radical}(3) are presented. The comparison of theoretical results obtained for the molecule, on Ag(lll) and Ag {radical}(3) x {radical}(3) surfaces, with STM measurement at RT, support the chemisorption with thiolate bonds to the Ag trimers on the HCT surface. The molecule is aligned with the Cp-Fe-Cp axis parallel to the surface, while the rotational freedom of the molecule is limited due to chemisorption. The presented adsorption model is supported by experiment and simulation. In the third part, the perfect Ag {radical}(3) x {radical}(3) is prepared and investigated by means of STM, focusing on structural and electronic characteristics. The different reconstructions and amounts of Ag on Si are investigated; the submonolayer amounts, Ag {radical}(3) x {radical}(3) wetting layers, perfect epitaxial layers and multilayer systems. The influence of wetting layer on electronic character of deposited Ag nanostructures is studied. The occurrence of effective single and double barriers in tunnelling microscopy and spectroscopy for the Ag {radical}(3) x <{radical}(3) system is investigated in the monolayer regime by varying the measurement and preparation conditions. The Coulomb Blockade oscillations are found for granular multilayer Ag films, whereas similar structures with existence of Ag {radical}(3) x {radical}(3) show only a single barrier characteristic. The vertical transport properties in this metal/ semiconductor system depend on the structure and bonding on the atomic scale and on the lateral two-dimensional properties of the interface.

  3. Ultra-Lightweight Hybrid Structured Mirror Project

    Data.gov (United States)

    National Aeronautics and Space Administration — MMCC is proposing herewith a hybrid structured mirror that combines the advantages of SiC membrane and magnesium graphite composite. The significance of magnesium...

  4. Plasmonic finite-thickness metal-semiconductor-metal waveguide as ultra-compact modulator

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Malureanu, Radu; Lavrinenko, Andrei

    2013-01-01

    We propose a plasmonic waveguide with semiconductor gain material for optoelectronic integrated circuits. We analyze properties of a finite-thickness metal-semiconductor-metal (F-MSM) waveguide to be utilized as an ultra-compact and fast plasmonic modulator. The InP-based semiconductor core allow...

  5. Finite-thickness metal-semiconductor-metal waveguide as plasmonic modulator

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Malureanu, Radu; Lavrinenko, Andrei

    2012-01-01

    We analyze a finite-thickness metal-semiconductor-metal waveguide to be utilized as an ultra-compact plasmonic modulator in optoelectronic integrated circuits. The InP-based semiconductor core allows electrical control of signal propagation. We show that using thin metal layers instead of thick o...

  6. Plasmonic modulator based on gain-assisted metal-semiconductor-metal waveguide

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia E.; Kulkova, Irina V.; Malureanu, Radu

    2012-01-01

    We investigate plasmonic modulators with a gain material to be implemented as ultra-compact and ultra-fast active nanodevices in photonic integrated circuits. We analyze metal-semiconductor-metal (MSM) waveguides with InGaAsP-based active material layers as ultra-compact plasmonic modulators. The...

  7. The dynamics of the laser-induced metal-semiconductor phase transition of samarium sulfide (SmS)

    International Nuclear Information System (INIS)

    Kaempfer, Tino

    2009-01-01

    The present thesis is dedicated to the experimental study of the metal-semiconductor phase transition of samarium sulfide (SmS): Temperature- and time-resolved experiments on the characterization of the phase transition of mixed-valence SmS samples (M-SmS) are presented. The measurement of the dynamics of the laser-induced phase transition pursues via time-resolved ultrashort-time microscopy and by X-ray diffraction with sub-picosecond time resolution. The electronic and structural processes, which follow an excitation of M-SmS with infrared femtosecond laser pulses, are physically interpreted on the base of the results obtained in this thesis and model imaginations. [de

  8. Euro hybrid materials and structures. Proceedings

    International Nuclear Information System (INIS)

    Hausmann, Joachim M.; Siebert, Marc

    2016-01-01

    In order to use the materials as best as possible, several different materials are usually mixed in one component, especially in the field of lightweight design. If these combinations of materials are joined inherently, they are called multi material design products or hybrid structures. These place special requirements on joining technology, design methods and manufacturing and are challenging in other aspects, too. The eight chapters with manuscripts of the presentations are: Chapter 1- Interface: What happens in the interface between the two materials? Chapter 2 - Corrosion and Residual Stresses: How about galvanic corrosion and thermal residual stresses in the contact zone of different materials? Chapter 3 - Characterization: How to characterize and test hybrid materials? Chapter 4 - Design: What is a suitable design and dimensioning method for hybrid structures? Chapter 5 - Machining and Processing: How to machine and process hybrid structures and materials? Chapter 6 - Component Manufacturing: What is a suitable manufacturing route for hybrid structures? Chapter 7 - Non-Destructive Testing and Quality Assurance: How to assure the quality of material and structures? Chapter 8 - Joining: How to join components of different materials?

  9. Metal-Semiconductor Reaction Phenomena and Microstructural Investigations of Laser Induced Regrowth of Silicon on Insulators.

    Science.gov (United States)

    1982-01-01

    tion. 3 _.34 5.0 LASER ASSISTED DIFFUSION AND ACTIVATION OF TIN FROM AN SnO 2/SiO 2 SOURCE The diffusion of impurities into a semiconductor substrate...11111.0 2 25 l22 1111111 . 12L5 .4 51 METAL- SEMICONDUCTOR REACTION PHENOMENA AND MICROSTRUCTURAL INVESTIGATIONS OF LASER INDUCED REGROWTH OF SILICON... Semiconductor Reaction Phenomena and Final Report Microstructural Investigations of Laser-Induced _Jan. I_9 t0_njani92 _ Regrowth of Silicon on

  10. Metal-Semiconductor Nanocomposites for High Efficiency Thermoelectric Power Generation

    Science.gov (United States)

    2013-12-07

    will be able to measure the thermoelectric properties on these p-type antimonide thermoelectric materials up to a higher temperature therefore a...energy-dependent carrier scattering without the inherent disadvantages of aluminum containing materials. In previous years of the program...DOE and from NASA in order to commercialize their antimonide MOCVD reactor. Structured Material Industries, Inc. grew all of the rare-earth InGaSb

  11. Electronic transport properties of carbon nanotube metal-semiconductor-metal

    Directory of Open Access Journals (Sweden)

    F Khoeini

    2008-07-01

    Full Text Available  In this work, we study electronic transport properties of a quasi-one dimensional pure semi-conducting Zigzag Carbon Nanotube (CNT attached to semi-infinite clean metallic Zigzag CNT leads, taking into account the influence of topological defect in junctions. This structure may behave like a field effect transistor. The calculations are based on the tight-binding model and Green’s function method, in which the local density of states(LDOS in the metallic section to semi-conducting section, and muli-channel conductance of the system are calculated in the coherent and linear response regime, numerically. Also we have introduced a circuit model for the system and investigated its current. The theoretical results obtained, can be a base, for developments in designing nano-electronic devices.

  12. Reaction Current Phenomenon in Bifunctional Catalytic Metal-Semiconductor Nanostructures

    Science.gov (United States)

    Hashemian, Mohammad Amin

    Energy transfer processes accompany every elementary step of catalytic chemical processes on material surface including molecular adsorption and dissociation on atoms, interactions between intermediates, and desorption of reaction products from the catalyst surface. Therefore, detailed understanding of these processes on the molecular level is of great fundamental and practical interest in energy-related applications of nanomaterials. Two main mechanisms of energy transfer from adsorbed particles to a surface are known: (i) adiabatic via excitation of quantized lattice vibrations (phonons) and (ii) non-adiabatic via electronic excitations (electron/hole pairs). Electronic excitations play a key role in nanocatalysis, and it was recently shown that they can be efficiently detected and studied using Schottky-type catalytic nanostructures in the form of measureable electrical currents (chemicurrents) in an external electrical circuit. These nanostructures typically contain an electrically continuous nanocathode layers made of a catalytic metal deposited on a semiconductor substrate. The goal of this research is to study the direct observations of hot electron currents (chemicurrents) in catalytic Schottky structures, using a continuous mesh-like Pt nanofilm grown onto a mesoporous TiO2 substrate. Such devices showed qualitatively different and more diverse signal properties, compared to the earlier devices using smooth substrates, which could only be explained on the basis of bifunctionality. In particular, it was necessary to suggest that different stages of the reaction are occurring on both phases of the catalytic structure. Analysis of the signal behavior also led to discovery of a formerly unknown (very slow) mode of the oxyhydrogen reaction on the Pt/TiO2(por) system occurring at room temperature. This slow mode was producing surprisingly large stationary chemicurrents in the range 10--50 microA/cm2. Results of the chemicurrent measurements for the bifunctional

  13. Metal/Semiconductor and Transparent Conductor/Semiconductor Heterojunctions in High Efficient Photoelectric Devices: Progress and Features

    Directory of Open Access Journals (Sweden)

    M. Melvin David Kumar

    2014-01-01

    Full Text Available Metal/semiconductor and transparent conductive oxide (TCO/semiconductor heterojunctions have emerged as an effective modality in the fabrication of photoelectric devices. This review is following a recent shift toward the engineering of TCO layers and structured Si substrates, incorporating metal nanoparticles for the development of next-generation photoelectric devices. Beneficial progress which helps to increase the efficiency and reduce the cost, has been sequenced based on efficient technologies involved in making novel substrates, TCO layers, and electrodes. The electrical and optical properties of indium tin oxide (ITO and aluminum doped zinc oxide (AZO thin films can be enhanced by structuring the surface of TCO layers. The TCO layers embedded with Ag nanoparticles are used to enhance the plasmonic light trapping effect in order to increase the energy harvesting nature of photoelectric devices. Si nanopillar structures which are fabricated by photolithography-free technique are used to increase light-active surface region. The importance of the structure and area of front electrodes and the effect of temperature at the junction are the value added discussions in this review.

  14. Hybrid Method Simulation of Slender Marine Structures

    DEFF Research Database (Denmark)

    Christiansen, Niels Hørbye

    is that they deal with time domain simulation of slender marine structures such as mooring lines and flexible risers used in deep sea offshore installations. The first part of the thesis describes how neural networks can be designed and trained to cover a large number of different sea states. Neural networks can......This present thesis consists of an extended summary and five appended papers concerning various aspects of the implementation of a hybrid method which combines classical simulation methods and artificial neural networks. The thesis covers three main topics. Common for all these topics...... that a single neural network can cover all relevant sea states. The applicability and performance of the present hybrid method is demonstrated on a numerical model of a mooring line attached to a floating offshore platform. The second part of the thesis demonstrates how sequential neural networks can be used...

  15. Hydrogen sensors using nitride-based semiconductor diodes: the role of metal/semiconductor interfaces.

    Science.gov (United States)

    Irokawa, Yoshihiro

    2011-01-01

    In this paper, I review my recent results in investigating hydrogen sensors using nitride-based semiconductor diodes, focusing on the interaction mechanism of hydrogen with the devices. Firstly, effects of interfacial modification in the devices on hydrogen detection sensitivity are discussed. Surface defects of GaN under Schottky electrodes do not play a critical role in hydrogen sensing characteristics. However, dielectric layers inserted in metal/semiconductor interfaces are found to cause dramatic changes in hydrogen sensing performance, implying that chemical selectivity to hydrogen could be realized. The capacitance-voltage (C-V) characteristics reveal that the work function change in the Schottky metal is not responsible mechanism for hydrogen sensitivity. The interface between the metal and the semiconductor plays a critical role in the interaction of hydrogen with semiconductor devises. Secondly, low-frequency C-V characterization is employed to investigate the interaction mechanism of hydrogen with diodes. As a result, it is suggested that the formation of a metal/semiconductor interfacial polarization could be attributed to hydrogen-related dipoles. In addition, using low-frequency C-V characterization leads to clear detection of 100 ppm hydrogen even at room temperature where it is hard to detect hydrogen by using conventional current-voltage (I-V) characterization, suggesting that low-frequency C-V method would be effective in detecting very low hydrogen concentrations.

  16. Hydrogen Sensors Using Nitride-Based Semiconductor Diodes: The Role of Metal/Semiconductor Interfaces

    Directory of Open Access Journals (Sweden)

    Yoshihiro Irokawa

    2011-01-01

    Full Text Available In this paper, I review my recent results in investigating hydrogen sensors using nitride-based semiconductor diodes, focusing on the interaction mechanism of hydrogen with the devices. Firstly, effects of interfacial modification in the devices on hydrogen detection sensitivity are discussed. Surface defects of GaN under Schottky electrodes do not play a critical role in hydrogen sensing characteristics. However, dielectric layers inserted in metal/semiconductor interfaces are found to cause dramatic changes in hydrogen sensing performance, implying that chemical selectivity to hydrogen could be realized. The capacitance-voltage (C-V characteristics reveal that the work function change in the Schottky metal is not responsible mechanism for hydrogen sensitivity. The interface between the metal and the semiconductor plays a critical role in the interaction of hydrogen with semiconductor devises. Secondly, low-frequency C-V characterization is employed to investigate the interaction mechanism of hydrogen with diodes. As a result, it is suggested that the formation of a metal/semiconductor interfacial polarization could be attributed to hydrogen-related dipoles. In addition, using low-frequency C-V characterization leads to clear detection of 100 ppm hydrogen even at room temperature where it is hard to detect hydrogen by using conventional current-voltage (I-V characterization, suggesting that low-frequency C-V method would be effective in detecting very low hydrogen concentrations.

  17. Structure of the Hermean magnetosphere: hybrid simulations

    Science.gov (United States)

    Travnicek, P.; Hellinger, P.

    We examine the interaction of the Hermean magnetosphere with the solar wind using global three dimensional hybrid plasma simulations. Hybrid simulations treat ions as particles and electrons as a fluid. Having ions as particles allows ion kinetic behavior and waves to be included in the physical treatment of the plasma as compared to magnetohydrodynamic (MHD) modeling that treats the plasma as a single magnetized fluid and does not include such kinetic effects. Kinetic effects are essential for understanding magnetospheric physics. Hybrid simulations scale to the ion inertial length and thus on a global scale are somewhat limited in spatial extent compared to an MHD simulation. We note effects caused by the scalling of the numerical model of the magnetized obstacle interacting with the solar wind flow with the full scale simulation. In this paper we shall focus on the study of the overal structure of the bow shock and magnetosheath formed in front of Mercury under different solar wind conditions, namely, in the perihelion and aphelion points of the excentric Hermean orbit. We examine the formation of the magnetospheric tail. We study particle distribution functions in different locations of the numerical model of the Hermean magnetosphere. We make qualitative comparison of the numerical results with the observations of Mariner 10. Hermean magnetosphere is estimated to be only a few times the planetary radius, it can fit within a hybrid simulation system. The overal structure of the interaction between a magnetized obstacle in the solar wind flow is determined by few basic parameters (namely the solar wind density, background magnetic field, and the speed of solar wind, and also the strength of the magnetic dipole of the obstacle and its radius). The structure of the interaction of the solar wind flow with Mercury is to a large extend unique when compared to other planets. For example, the magnetic moment of the Mercury is over 1000 times smaller than that of the

  18. Electrical Control of Magnetic Dynamics in Hybrid Metal-Semiconductor Systems

    Science.gov (United States)

    2014-07-25

    magnetized domains in ferromagnetic CoFe layers on BiFeO3 by a low-voltage (5-7 V) signal applied in the out-of-plane direction. The paper...nl402651r J. T. Heron, D. G. Schlom, R. Ramesh. Electric field control of magnetism using BiFeO3 -based heterostructures, APPLIED PHYSICS REVIEWS, (06 2014...0. doi: 10.1063/1.4870957 Christian M. Schlepu?tz, Carolina Adamo, Darrell G. Schlom, Roy Clarke, Yongsoo Yang. Untilting BiFeO3 : The influence of

  19. High performance hybrid magnetic structure for biotechnology applications

    Science.gov (United States)

    Humphries, David E [El Cerrito, CA; Pollard, Martin J [El Cerrito, CA; Elkin, Christopher J [San Ramon, CA

    2009-02-03

    The present disclosure provides a high performance hybrid magnetic structure made from a combination of permanent magnets and ferromagnetic pole materials which are assembled in a predetermined array. The hybrid magnetic structure provides means for separation and other biotechnology applications involving holding, manipulation, or separation of magnetic or magnetizable molecular structures and targets. Also disclosed are further improvements to aspects of the hybrid magnetic structure, including additional elements and for adapting the use of the hybrid magnetic structure for use in biotechnology and high throughput processes.

  20. Structure-property relationship of compounds with pyrite and shandite structure with metal-semiconductor transition in InSnCo{sub 3}S{sub 2}; Struktur-Eigenschafts-Beziehungen von Verbindungen mit Pyrit- und Shanditstruktur mit Metall-Halbleiter-Uebergang in InSnCo{sub 3}S{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Rothballer, Jan

    2014-12-23

    The aim of this Ph.D thesis is to correlate theoretical calculations and experimental data to understand the building and stabilities of structures to influence the properties due to applications. Properties of compounds are defined by their electronic structures. The electronic structure can be influenced by substitution of elements or even doping. As a matter of fact, electronic design is a basic principle in materials research. It can help to change or switch the electric conductivity or the magnetism of a starting compound. I analyzed compounds with pyrite-type structure and Sn{sub 2}Co{sub 3}S{sub 2} and related compounds to these. Its electronic as well as its crystallographic structure is highly flexible and Sn{sub 2}Co{sub 3}S{sub 2} is a half metallic ferromagnet. By substituting In to Sn one gets a semiconductor due to indium-tin ordering. By doping sulfur against selenium, the magnetism is highly influenced. To verify and to understand these effects I did magnetic, XRD, neutron and conductivity measurements as well as DFT calculations in direct and reciprocal space.

  1. Hysteresis phenomena at metal-semiconductor phase transformation in vanadium oxides

    International Nuclear Information System (INIS)

    Lanskaya, T.G.; Merkulov, I.A.; Chudnovski , F.A.

    1978-01-01

    The hysteresis phenomena during the metal-semiconductor phase transformation (MSPT) in vanadium oxides are investigated. It is shown experimentally that the hysteresis effects during MSPT in vanadium oxides are associated not only with the martensite nature of the transformation, but also with activation processes. It is shown that the hysteresis phenomena during MSPT may be described by the distribution function of microregions of the crystal in the phase transformation temperature T 0 and the coercive temperature Tsub(c). An experimental method for constructing this distribution function was worked out. An analysis of the experimental data shows that finely dispersed films are characterized by a wide range of values of T 0 and Tsub(c) (55 deg C 0 <65 deg C, 6 deg C< Tsub(c)<12 deg C). The peculiarities of the optical recording of information on monocrystal and finely dispersed films are considered

  2. General atomistic approach for modeling metal-semiconductor interfaces using density functional theory and nonequilibrium Green's function

    DEFF Research Database (Denmark)

    Stradi, Daniele; Martinez, Umberto; Blom, Anders

    2016-01-01

    an atomistic approach based on density functional theory and nonequilibrium Green's function, which includes all the relevant ingredients required to model realistic metal-semiconductor interfaces and allows for a direct comparison between theory and experiments via I-Vbias curve simulations. We apply...

  3. Hybrid Testing of Composite Structures with Single-Axis Control

    DEFF Research Database (Denmark)

    Waldbjørn, Jacob Paamand; Høgh, Jacob Herold; Stang, Henrik

    2013-01-01

    Hybrid testing is a substructuring technique where a structure is emulated by modelling a part of it in a numerical model while testing the remainder experimentally. Previous research in hybrid testing has been performed on multi-component structures e.g. damping fixtures, however in this paper...... a hybrid testing platform is introduced for single-component hybrid testing. In this case, the boundary between the numerical model and experimental setup is defined by multiple Degrees-Of-Freedoms (DOFs) which highly complicate the transferring of response between the two substructures. Digital Image...... Correlation (DIC) is therefore implemented for displacement control of the experimental setup. The hybrid testing setup was verified on a multicomponent structure consisting of a beam loaded in three point bending and a numerical structure of a frame. Furthermore, the stability of the hybrid testing loop...

  4. Breaking Dense Structures: Proving Stability of Densely Structured Hybrid Systems

    Directory of Open Access Journals (Sweden)

    Eike Möhlmann

    2015-06-01

    Full Text Available Abstraction and refinement is widely used in software development. Such techniques are valuable since they allow to handle even more complex systems. One key point is the ability to decompose a large system into subsystems, analyze those subsystems and deduce properties of the larger system. As cyber-physical systems tend to become more and more complex, such techniques become more appealing. In 2009, Oehlerking and Theel presented a (de-composition technique for hybrid systems. This technique is graph-based and constructs a Lyapunov function for hybrid systems having a complex discrete state space. The technique consists of (1 decomposing the underlying graph of the hybrid system into subgraphs, (2 computing multiple local Lyapunov functions for the subgraphs, and finally (3 composing the local Lyapunov functions into a piecewise Lyapunov function. A Lyapunov function can serve multiple purposes, e.g., it certifies stability or termination of a system or allows to construct invariant sets, which in turn may be used to certify safety and security. In this paper, we propose an improvement to the decomposing technique, which relaxes the graph structure before applying the decomposition technique. Our relaxation significantly reduces the connectivity of the graph by exploiting super-dense switching. The relaxation makes the decomposition technique more efficient on one hand and on the other allows to decompose a wider range of graph structures.

  5. Influence of thermodynamically unfavorable secondary structures on DNA hybridization kinetics

    Science.gov (United States)

    Hata, Hiroaki; Kitajima, Tetsuro

    2018-01-01

    Abstract Nucleic acid secondary structure plays an important role in nucleic acid–nucleic acid recognition/hybridization processes, and is also a vital consideration in DNA nanotechnology. Although the influence of stable secondary structures on hybridization kinetics has been characterized, unstable secondary structures, which show positive ΔG° with self-folding, can also form, and their effects have not been systematically investigated. Such thermodynamically unfavorable secondary structures should not be ignored in DNA hybridization kinetics, especially under isothermal conditions. Here, we report that positive ΔG° secondary structures can change the hybridization rate by two-orders of magnitude, despite the fact that their hybridization obeyed second-order reaction kinetics. The temperature dependence of hybridization rates showed non-Arrhenius behavior; thus, their hybridization is considered to be nucleation limited. We derived a model describing how ΔG° positive secondary structures affect hybridization kinetics in stopped-flow experiments with 47 pairs of oligonucleotides. The calculated hybridization rates, which were based on the model, quantitatively agreed with the experimental rate constant. PMID:29220504

  6. Proximity effect in normal metal-multiband superconductor hybrid structures

    NARCIS (Netherlands)

    Brinkman, Alexander; Golubov, Alexandre Avraamovitch; Kupriyanov, M. Yu

    2004-01-01

    A theory of the proximity effect in normal metal¿multiband superconductor hybrid structures is formulated within the quasiclassical Green's function formalism. The quasiclassical boundary conditions for multiband hybrid structures are derived in the dirty limit. It is shown that the existence of

  7. Hybrid logic on linear structures: expressivity and complexity

    NARCIS (Netherlands)

    Franceschet, M.; de Rijke, M.; Schlingoff, B.-H.

    2003-01-01

    We investigate expressivity and complexity of hybrid logics on linear structures. Hybrid logics are an enrichment of modal logics with certain first-order features which are algorithmically well behaved. Therefore, they are well suited for the specification of certain properties of computational

  8. Hybrid structures based on quantum dots and graphene nanobelts

    Science.gov (United States)

    Reznik, I. A.; Gromova, Yu. A.; Zlatov, A. S.; Baranov, M. A.; Orlova, A. O.; Moshkalev, S. A.; Maslov, V. G.; Baranov, A. V.; Fedorov, A. V.

    2017-01-01

    Luminescence and photoelectric properties of hybrid structures based on CdSe/ZnS quantum dots (QDs) and multilayer graphene have been investigated. A correlation between the luminescence quantum yield of QDs and their photoelectric properties in hybrid structures is established. It is shown that a decrease in the QD luminescence quantum yield due to adsorption of 1-(2-pyridylazo)-2-naphtol azo dye molecules onto the QD surface and a photoinduced increase in the QD luminescence quantum yield are accompanied by a symbate change in the hybrid structure photoconductivity.

  9. Numerical investigation of metal-semiconductor-insulator-semiconductor passivated hole contacts based on atomic layer deposited AlO x

    Science.gov (United States)

    Ke, Cangming; Xin, Zheng; Ling, Zhi Peng; Aberle, Armin G.; Stangl, Rolf

    2017-08-01

    Excellent c-Si tunnel layer surface passivation has been obtained recently in our lab, using atomic layer deposited aluminium oxide (ALD AlO x ) in the tunnel layer regime of 0.9 to 1.5 nm, investigated to be applied for contact passivation. Using the correspondingly measured interface properties, this paper compares the theoretical collection efficiency of a conventional metal-semiconductor (MS) contact on diffused p+ Si to a metal-semiconductor-insulator-semiconductor (MSIS) contact on diffused p+ Si or on undoped n-type c-Si. The influences of (1) the tunnel layer passivation quality at the tunnel oxide interface (Q f and D it), (2) the tunnel layer thickness and the electron and hole tunnelling mass, (3) the tunnel oxide material, and (4) the semiconductor capping layer material properties are investigated numerically by evaluation of solar cell efficiency, open-circuit voltage, and fill factor.

  10. Terahertz Modulator based on Metamaterials integrated with Metal-Semiconductor-Metal Varactors

    Science.gov (United States)

    Nouman, Muhammad Tayyab; Kim, Hyun-Woong; Woo, Jeong Min; Hwang, Ji Hyun; Kim, Dongju; Jang, Jae-Hyung

    2016-01-01

    The terahertz (THz) band of the electromagnetic spectrum, with frequencies ranging from 300 GHz to 3 THz, has attracted wide interest in recent years owing to its potential applications in numerous areas. Significant progress has been made toward the development of devices capable of actively controlling terahertz waves; nonetheless, further advances in device functionality are necessary for employment of these devices in practical terahertz systems. Here, we demonstrate a low voltage, sharp switching terahertz modulator device based on metamaterials integrated with metal semiconductor metal (MSM) varactors, fabricated on an AlGaAs/InGaAs based heterostructure. By varying the applied voltage to the MSM-varactor located at the center of split ring resonator (SRR), the resonance frequency of the SRR-based metamaterial is altered. Upon varying the bias voltage from 0 V to 3 V, the resonance frequency exhibits a transition from 0.52 THz to 0.56 THz, resulting in a modulation depth of 45 percent with an insertion loss of 4.3 dB at 0.58 THz. This work demonstrates a new approach for realizing active terahertz devices with improved functionalities. PMID:27194128

  11. Terahertz Modulator based on Metamaterials integrated with Metal-Semiconductor-Metal Varactors.

    Science.gov (United States)

    Nouman, Muhammad Tayyab; Kim, Hyun-Woong; Woo, Jeong Min; Hwang, Ji Hyun; Kim, Dongju; Jang, Jae-Hyung

    2016-05-19

    The terahertz (THz) band of the electromagnetic spectrum, with frequencies ranging from 300 GHz to 3 THz, has attracted wide interest in recent years owing to its potential applications in numerous areas. Significant progress has been made toward the development of devices capable of actively controlling terahertz waves; nonetheless, further advances in device functionality are necessary for employment of these devices in practical terahertz systems. Here, we demonstrate a low voltage, sharp switching terahertz modulator device based on metamaterials integrated with metal semiconductor metal (MSM) varactors, fabricated on an AlGaAs/InGaAs based heterostructure. By varying the applied voltage to the MSM-varactor located at the center of split ring resonator (SRR), the resonance frequency of the SRR-based metamaterial is altered. Upon varying the bias voltage from 0 V to 3 V, the resonance frequency exhibits a transition from 0.52 THz to 0.56 THz, resulting in a modulation depth of 45 percent with an insertion loss of 4.3 dB at 0.58 THz. This work demonstrates a new approach for realizing active terahertz devices with improved functionalities.

  12. Hot-electron-based solar energy conversion with metal-semiconductor nanodiodes

    Science.gov (United States)

    Lee, Young Keun; Lee, Hyosun; Lee, Changhwan; Hwang, Euyheon; Park, Jeong Young

    2016-06-01

    Energy dissipation at metal surfaces or interfaces between a metal and a dielectric generally results from elementary excitations, including phonons and electronic excitation, once external energy is deposited to the surface/interface during exothermic chemical processes or an electromagnetic wave incident. In this paper, we outline recent research activities to develop energy conversion devices based on hot electrons. We found that photon energy can be directly converted to hot electrons and that hot electrons flow through the interface of metal-semiconductor nanodiodes where a Schottky barrier is formed and the energy barrier is much lower than the work function of the metal. The detection of hot electron flow can be successfully measured using the photocurrent; we measured the photoyield of photoemission with incident photons-to-current conversion efficiency (IPCE). We also show that surface plasmons (i.e. the collective oscillation of conduction band electrons induced by interaction with an electromagnetic field) are excited on a rough metal surface and subsequently decay into secondary electrons, which gives rise to enhancement of the IPCE. Furthermore, the unique optical behavior of surface plasmons can be coupled with dye molecules, suggesting the possibility for producing additional channels for hot electron generation.

  13. Metal-semiconductor transition and negative magneto-resistance in degenerate ultrathin tin oxide films

    Energy Technology Data Exchange (ETDEWEB)

    Bansal, Shikha; Kashyap, Subhash C.; Pandya, Dinesh K., E-mail: dkpandya@physics.iitd.ac.in

    2015-10-15

    A study of electron- and magneto-transport behavior of ultrathin SnO{sub 2} films of thickness ≤40 nm with high conductivity of 537 Ω{sup −1} cm{sup −1} deposited on glass substrate by using DC reactive sputtering has been carried out at low temperature. Hall effect measurements revealed these SnO{sub 2} films to be degenerate down to 40 K. The films with thickness >5 nm are found to undergo a metal-semiconductor transition below 140 K, and show a negative MR of ∼1.5% at a magnetic field of 0.9 T below 40 K. Both these phenomena have been ascribed to the presence of weak localization of electrons at low temperature. Electron transport behavior has been explained using quantum correction to conductivity. Estimated inelastic scattering lengths were found to be longer than the film thickness which supports two-dimensional nature of electron- and magneto-transport in these ultrathin films. - Highlights: • Ultrathin SnO{sub 2} films show a high conductivity of the order of 10{sup 2} S. • Metal to semiconductor (MS) transition occurs in all the ultrathin SnO{sub 2} films of thickness > 5 nm. • All the samples show degenerate semiconductor behavior. • A negative MR is observed below 40 K in these ultrathin films. • MS transition and negative MR have been explained using weak localization effect.

  14. Fermi level dependent native defect formation: Consequences for metal-semiconductor and semiconductor-semiconductor interfaces

    International Nuclear Information System (INIS)

    Walukiewicz, W.

    1988-02-01

    The amphoteric native defect model of the Schottky barrier formation is used to analyze the Fermi level pinning at metal/semiconductor interfaces for submonolayer metal coverages. It is assumed that the energy required for defect generation is released in the process of surface back-relaxation. Model calculations for metal/GaAs interfaces show a weak dependence of the Fermi level pinning on the thickness of metal deposited at room temperature. This weak dependence indicates a strong dependence of the defect formation energy on the Fermi level, a unique feature of amphoteric native defects. This result is in very good agreement with experimental data. It is shown that a very distinct asymmetry in the Fermi level pinning on p- and n-type GaAs observed at liquid nitrogen temperatures can be understood in terms of much different recombination rates for amphoteric native defects in those two types of materials. Also, it is demonstrated that the Fermi level stabilization energy, a central concept of the amphoteric defect system, plays a fundamental role in other phenomena in semiconductors such as semiconductor/semiconductor heterointerface intermixing and saturation of free carrier concentration. 33 refs., 6 figs

  15. Prediction of the threshold voltage of GaAs ion-implanted metal-semiconductor field-effect transistors

    Directory of Open Access Journals (Sweden)

    Gorev N. B.

    2007-12-01

    Full Text Available It is shown that the threshold voltage of a GaAs ion-implanted metal-semiconductor field-effect transistor corresponds with a good accuracy to the voltage at which an inflection point appears in the capacitance-voltage characteristic. A method for predicting the threshold voltage of ion-implanted field-effect transistors using capacitance-voltage measurements prior to contact formation is proposed.

  16. A phased approach to enable hybrid simulation of complex structures

    Science.gov (United States)

    Spencer, Billie F.; Chang, Chia-Ming; Frankie, Thomas M.; Kuchma, Daniel A.; Silva, Pedro F.; Abdelnaby, Adel E.

    2014-08-01

    Hybrid simulation has been shown to be a cost-effective approach for assessing the seismic performance of structures. In hybrid simulation, critical parts of a structure are physically tested, while the remaining portions of the system are concurrently simulated computationally, typically using a finite element model. This combination is realized through a numerical time-integration scheme, which allows for investigation of full system-level responses of a structure in a cost-effective manner. However, conducting hybrid simulation of complex structures within large-scale testing facilities presents significant challenges. For example, the chosen modeling scheme may create numerical inaccuracies or even result in unstable simulations; the displacement and force capacity of the experimental system can be exceeded; and a hybrid test may be terminated due to poor communication between modules (e.g., loading controllers, data acquisition systems, simulation coordinator). These problems can cause the simulation to stop suddenly, and in some cases can even result in damage to the experimental specimens; the end result can be failure of the entire experiment. This study proposes a phased approach to hybrid simulation that can validate all of the hybrid simulation components and ensure the integrity large-scale hybrid simulation. In this approach, a series of hybrid simulations employing numerical components and small-scale experimental components are examined to establish this preparedness for the large-scale experiment. This validation program is incorporated into an existing, mature hybrid simulation framework, which is currently utilized in the Multi-Axial Full-Scale Sub-Structuring Testing and Simulation (MUST-SIM) facility of the George E. Brown Network for Earthquake Engineering Simulation (NEES) equipment site at the University of Illinois at Urbana-Champaign. A hybrid simulation of a four-span curved bridge is presented as an example, in which three piers are

  17. Hybrid Bridge Structures Made of Frp Composite and Concrete

    Science.gov (United States)

    Rajchel, Mateusz; Siwowski, Tomasz

    2017-09-01

    Despite many advantages over the conventional construction materials, the contemporary development of FRP composites in bridge engineering is limited due to high initial cost, low stiffness (in case of glass fibers) and sudden composite failure mode. In order to reduce the given limitations, mixed (hybrid) solutions connecting the FRP composites and conventional construction materials, including concrete, have been tested in many countries for 20 years. Shaping the hybrid structures based on the attributes of particular materials, aims to increase stiffness and reduce cost without losing the carrying capacity, lightness and easiness of bridges that includes such hybrid girders, and to avoid the sudden dangerous failure mode. In the following article, the authors described examples of hybrid road bridges made of FRP composite and concrete within the time of 20 years and presented the first Polish hybrid FRP-concrete road bridge. Also, the directions of further research, necessary to spread these innovative, advanced and sustainable bridge structures were indicated.

  18. Hybrid organic/inorganic position-sensitive detectors based on PEDOT:PSS/n-Si

    Science.gov (United States)

    Javadi, Mohammad; Gholami, Mahdiyeh; Torbatiyan, Hadis; Abdi, Yaser

    2018-03-01

    Various configurations like p-n junctions, metal-semiconductor Schottky barriers, and metal-oxide-semiconductor structures have been widely used in position-sensitive detectors. In this report, we propose a PEDOT:PSS/n-Si heterojunction as a hybrid organic/inorganic configuration for position-sensitive detectors. The influence of the thickness of the PEDOT:PSS layer, the wavelength of incident light, and the intensity of illumination on the device performance are investigated. The hybrid PSD exhibits very high sensitivity (>100 mV/mm), excellent nonlinearity (0.995) with a response time of PEDOT:PSS/n-Si heterojunction are very promising for developing a new class of position-sensitive detectors based on the hybrid organic/inorganic junctions.

  19. Exploratory Topology Modelling of Form-Active Hybrid Structures

    DEFF Research Database (Denmark)

    Holden Deleuran, Anders; Pauly, Mark; Tamke, Martin

    2016-01-01

    The development of novel form-active hybrid structures (FAHS) is impeded by a lack of modelling tools that allow for exploratory topology modelling of shaped assemblies. We present a flexible and real-time computational design modelling pipeline developed for the exploratory modelling of FAHS...... that enables designers and engineers to iteratively construct and manipulate form-active hybrid assembly topology on the fly. The pipeline implements Kangaroo2's projection-based methods for modelling hybrid structures consisting of slender beams and cable networks. A selection of design modelling sketches...... is presented in which the developed modelling pipeline has been integrated to explore the design space delineated by FAHS....

  20. Development of Room Temperature Excitonic Lasing From ZnO and MgZnO Thin Film Based Metal-Semiconductor-Metal Devices

    Science.gov (United States)

    Suja, Mohammad Zahir Uddin

    Room temperature excitonic lasing is demonstrated and developed by utilizing metal-semiconductor-metal devices based on ZnO and MgZnO materials. At first, Cu-doped p-type ZnO films are grown on c-sapphire substrates by plasma-assisted molecular beam epitaxy. Photoluminescence (PL) experiments reveal a shallow acceptor state at 0.15 eV above the valence band edge. Hall effect results indicate that a growth condition window is found for the formation of p-type ZnO thin films and the best conductivity is achieved with a high hole concentration of 1.54x1018 cm-3, a low resistivity of 0.6 O cm and a moderate mobility of 6.65 cm2 V -1 s-1 at room temperature. Metal oxide semiconductor (MOS) capacitor devices have been fabricated on the Cu-doped ZnO films and the characteristics of capacitance-voltage measurements demonstrate that the Cu-doped ZnO thin films under proper growth conditions are p-type. Seebeck measurements on these Cu-doped ZnO samples lead to positive Seebeck coefficients and further confirm the p-type conductivity. Other measurements such as XRD, XPS, Raman and absorption are also performed to elucidate the structural and optical characteristics of the Cu-doped p-type ZnO films. The p-type conductivity is explained to originate from Cu substitution of Zn with a valency of +1 state. However, all p-type samples are converted to n-type over time, which is mostly due to the carrier compensation from extrinsic defects of ZnO. To overcome the stability issue of p-type ZnO film, alternate devices other than p-n junction has been developed. Electrically driven plasmon-exciton coupled random lasing is demonstrated by incorporating Ag nanoparticles on Cu-doped ZnO metal-semiconductor-metal (MSM) devices. Both photoluminescence and electroluminescence studies show that emission efficiencies have been enhanced significantly due to coupling between ZnO excitons and Ag surface plasmons. With the incorporation of Ag nanoparticles on ZnO MSM structures, internal quantum

  1. Spectroscopic Studies of the Electronic Structure of Metal-Semiconductor and Vacuum-Semiconductor Interfaces.

    Science.gov (United States)

    1982-12-31

    and D.E. Eastman, submitted to Phys. Rev. Lett.). 7. Surface Electronic Properties of lon- Implated LAser-amealed Si(111) Highly-degenerate As-doped n...White, Surface Electronic Properties of Ion- implated Laser-annealed Si(111), Laser and Electron-Beam Interactions with Solids, ed. by B.R. Appleton and

  2. Nafion–clay hybrids with a network structure

    KAUST Repository

    Burgaz, Engin

    2009-05-01

    Nafion-clay hybrid membranes with a unique microstructure were synthesized using a fundamentally new approach. The new approach is based on depletion aggregation of suspended particles - a well-known phenomenon in colloids. For certain concentrations of clay and polymer, addition of Nafion solution to clay suspensions in water leads to a gel. Using Cryo-TEM we show that the clay particles in the hybrid gels form a network structure with an average cell size in the order of 500 nm. The hybrid gels are subsequently cast to produce hybrid Nafion-clay membranes. Compared to pure Nafion the swelling of the hybrid membranes in water and methanol is dramatically reduced while their selectivity (ratio of conductivity over permeability) increases. The small decrease of ionic conductivity for the hybrid membranes is more than compensated by the large decrease in methanol permeability. Lastly the hybrid membranes are much stiffer and can withstand higher temperatures compared to pure Nafion. Both of these characteristics are highly desirable for use in fuel cell applications, since a) they will allow the use of a thinner membrane circumventing problems associated with the membrane resistance and b) enable high temperature applications. © 2009 Elsevier Ltd. All rights reserved.

  3. Electrical properties of nanosized non-barrier inhomogeneities in Zn-based metal-semiconductor contacts to InP

    DEFF Research Database (Denmark)

    Clausen, Thomas; Leistiko, Otto

    1998-01-01

    We have found that the electrical properties of carriers across the metal-semiconductor interface for alloyed Zn based metallizations to n- and p-InP are dominated by nanosized non-barrier inhomogeneities. The effective area covered by the nanosized regions is a small fraction of the contact area...... resulting in high values of the specific contact resistance to p-InP. For n(-)-InP, thermionic emission across nanosized inhomogeneities dominates the carrier flow when T-ann > 440 degrees C. (C) 1998 Elsevier Science B.V....

  4. Hybrid structures for molecular level sensing

    Science.gov (United States)

    Lemieux, Melburne Charles

    With substantial molecular mobility and segment dynamics relative to metals and ceramics, all polymeric materials, to some extent, are stimuli-responsive by exhibiting pronounced chemical and physical changes in the backbone, side chains, segments, or end groups induced by changes in the local environment. Thus, the push to incorporate polymeric materials as sensing/responsive nanoscale layers into next-generation miniaturized sensor applications is a natural progression. The significance and impact of this research is wide-ranging because it offers design considerations and presents results in perhaps two of the most critical broad areas of nanotechnology: ultrathin multifunctional polymer coatings and miniaturized sensors. In this work, direct evidence is given showing that polymer coatings comprised of deliberately selected molecular segments with very different chemistry can have switchable properties, and that the surface composition can be precisely controlled, and thus properties can be tuned: all in films on the order of 20 nm and less. Furthermore, active sensing layers in the form of plasma-polymerized polymers are successfully incorporated into actual silicon based microsensors resulting in a novel hybrid organic/inorganic materials platform for microfabricated MEMS sensors with record performance far beyond contemporary sensors in terms of detection sensitivity to various environments. The results produced in this research show thermal sensors with more than two orders of magnitude better sensitivity than what is attainable currently. In addition, a humidity response on the order of parts per trillion, which is four orders of magnitude more sensitive than current designs is achieved. Molecular interactions and forces for organic molecules are characterized at the picoscale to optimize polymeric nanoscale layer design that in turn optimize and lead to microscale hybrid sensors with unprecedented sensitivities.

  5. Dissecting the hybridization of oligonucleotides to structured complementary sequences.

    Science.gov (United States)

    Peracchi, Alessio

    2016-06-01

    When oligonucleotides hybridize to long target molecules, the process is slowed by the secondary structure in the targets. The phenomenon has been analyzed in several previous studies, but many details remain poorly understood. I used a spectrofluorometric strategy, focusing on the formation/breaking of individual base pairs, to study the kinetics of association between a DNA hairpin and >20 complementary oligonucleotides ('antisenses'). Hybridization rates differed by over three orders of magnitude. Association was toehold-mediated, both for antisenses binding to the target's ends and for those designed to interact with the loop. Binding of these latter, besides being consistently slower, was affected to variable, non-uniform extents by the asymmetric loop structure. Divalent metal ions accelerated hybridization, more pronouncedly when nucleation occurred at the loop. Incorporation of locked nucleic acid (LNA) residues in the antisenses substantially improved the kinetics only when LNAs participated to the earliest hybridization steps. The effects of individual LNAs placed along the antisense indicated that the reaction transition state occurred after invading at least the first base pair of the stem. The experimental approach helps dissect hybridization reactions involving structured nucleic acids. Toehold-dependent, nucleation-invasion models appear fully appropriate for describing such reactions. Estimating the stability of nucleation complexes formed at internal toeholds is the major hurdle for the quantitative prediction of hybridization rates. While analyzing the mechanisms of a fundamental biochemical process (hybridization), this work also provides suggestions for the improvement of technologies that rely on such process. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Protein structure prediction using hybrid AI methods

    Energy Technology Data Exchange (ETDEWEB)

    Guan, X.; Mural, R.J.; Uberbacher, E.C.

    1993-11-01

    This paper describes a new approach for predicting protein structures based on Artificial Intelligence methods and genetic algorithms. We combine nearest neighbor searching algorithms, neural networks, heuristic rules and genetic algorithms to form an integrated system to predict protein structures from their primary amino acid sequences. First we describe our methods and how they are integrated, and then apply our methods to several protein sequences. The results are very close to the real structures obtained by crystallography. Parallel genetic algorithms are also implemented.

  7. Structural properties of maize hybrids established by infrared spectra

    Directory of Open Access Journals (Sweden)

    Radenović Čedomir N.

    2015-01-01

    Full Text Available This paper discusses the application of the infrared (IR spectroscopy method for determination of structural properties of maize hybrid grains. The IR spectrum of maize grain has been registered in the following hybrids: ZP 341, ZP 434 and ZP 505. The existence of spectral bands varying in both number and intensity, as well as their shape, frequency and kinetics have been determined. They have been determined by valence oscillations and deformation oscillations of the following organic compounds: alkanes, alkenes, alkynes, amides, alcohols, ethers, carboxylic acids, esters and aldehydes and ketones, characteristic for biogenic compounds such as carbohydrates, proteins and lipids. In this way, possible changes in the grain structure of observed maize hybrids could be detected.

  8. A hybrid dielectric and iris loaded periodic accelerating structure

    International Nuclear Information System (INIS)

    Zou, P.; Xiao, L.; Sun, X.; Gai, W.

    2001-01-01

    One disadvantage of conventional iris-loaded accelerating structures is the high ratio of the peak surface electric field to the peak axial electric field useful for accelerating a beam. Typically this ratio E s /E a ≥ 2. The high surface electric field relative to the accelerating gradient may prove to be a limitation for realizing technologies for very high gradient accelerators. In this paper, we present a scheme that uses a hybrid dielectric and iris loaded periodic structure to reduce E s /E a to near unity, while the shunt impedance per unit length r and the quality factor Q compare favorably with conventional metallic structures. The analysis based on MAFIA simulations of such structures shows that we can lower the peak surface electric field close to the accelerating gradient while maintaining high acceleration efficiency as measured by r/Q. Numerical examples of X-band hybrid accelerating structures are given

  9. Calculation of hybrid joints used in modern aerospace structures

    Directory of Open Access Journals (Sweden)

    Marcel STERE

    2011-12-01

    Full Text Available The state – of - the art of aeronautical structures show that parts are manufactured and subsequently assembled with the use of fasteners and/ or bonding. Adhesive bonding is a key technology to low weight, high fatigue resistance, robustness and an attractive design for cost structures.The paper results resolve significant problems for two groups of end-users:1 for the aerospace design office: a robust procedure for the design of the hybrid joint structural components;2 for the aeronautical repair centres: a useful procedure for structural design and analysis with significant cost savings.

  10. Contribution to the study of rectification at the metal-semiconductor contact: analysis of aging in silicon Schottky diodes

    International Nuclear Information System (INIS)

    Ponpon, J.-P.

    1979-01-01

    The formation of the barrier height and the aging of metal-semiconductor contacts during exposure to air have been studied. The evolution of the electrical characteristics, especially the barrier height, of silicon Schottky diodes results from the diffusion of oxygen through the electrode and its accumulation at the interface. The diffusion coefficient of oxygen has been deduced for each metal used. In a first step the oxygen neutralize a fixed positive charge which remains at the semiconductor surface after etching; then, as silicon is oxidized, a MIS device is formed. Similar results have been obtained in the case of germanium, while no aging appears with cadmium telluride. In this case the barrier height seems to be determined by chemical reactions at the interface [fr

  11. The Effect of Metal-Semiconductor Contact on the Transient Photovoltaic Characteristic of HgCdTe PV Detector

    Directory of Open Access Journals (Sweden)

    Haoyang Cui

    2013-01-01

    Full Text Available The transient photovoltaic (PV characteristic of HgCdTe PV array is studied using an ultrafast laser. The photoresponse shows an apparent negative valley first, then it evolves into a positive peak. By employing a combined theoretical model of pn junction and Schottky potential, this photo-response polarity changing curves can be interpreted well. An obvious decreasing of ratio of negative valley to positive peak can be realized by limiting the illumination area of the array electrode. This shows that the photoelectric effect of Schottky barrier at metal-semiconductor (M/S interface is suppressed, which will verify the correctness of the model. The characteristic parameters of transient photo-response induced from p-n junction and Schottky potential are extracted by fitting the response curve utilizing this model. It shows that the negative PV response induced by the Schottky barrier decreases the positive photovoltage generated by the pn junction.

  12. Hybrid Optimization in the Design of Reciprocal Structures

    DEFF Research Database (Denmark)

    Parigi, Dario; Kirkegaard, Poul Henning; Sassone, Mario

    2012-01-01

    . In this paper it is shown that the geometrically compatible position of the elements could be determined by local search algorithm gradient-based (GB). However the control on which bar sit on the top or in the bottom at each connection can be regarded as a topological problem and require the use of algorithms...... that explore the global domain of solutions as genetic algorithms (GAs). The benchmark tests show that when the control on the topology is required the best result is obtained by a hybrid approach that combines the global search of the GA with the local search of a GB algorithm. The optimization method......The paper presents a method to generate the geometry of reciprocal structures by means of a hybrid optimization procedure. The geometry of reciprocal structures where elements are sitting on the top or in the bottom of each other is extremely difficult to predict because of the non...

  13. DFT charge transfer of hybrid molecular ferrocene/Si structures

    International Nuclear Information System (INIS)

    Calborean, Adrian; Buimaga-Iarinca, Luiza; Graur, Florin

    2015-01-01

    The electrochemical behavior and electronic properties of redox-active ferrocenes grafted onto semiconductor Si(100) substrate were investigated theoretically by first-principles calculations. Organic molecules were attached via the formation of Si-C covalent bonds through two different linkers: vinyl (direct grafting), and N 3 (CH 2 ) 11 (indirect grafting). Redox energies and the electronic properties relating to different spacers in hybrid ferrocene Fc/Si and ferrocenium Fc + /Si structures were theoretically extracted and compared with experimental cyclic voltametry data. Electronic charge transfers are discussed through the alignment positions of the frontier orbitals of the molecule with respect to the Si substrate gap. Periodic boundary conditions were used to investigate the Si(100) as a slab surface and hybrid Fc/Si structures. The resulting projected density of states (PDOS) were compared with molecular results and discussed in the light of experimental data. (paper)

  14. Development of Hybrid Product Breakdown Structure for NASA Ground Systems

    Science.gov (United States)

    Monaghan, Mark W.; Henry, Robert J.

    2013-01-01

    The Product Breakdown Structure is traditionally a method of identification of the products of a project in a tree structure. It is a tool used to assess, plan, document, and display the equipment requirements for a project. It is part of a product based planning technique, and attempts to break down all components of a project in as much detail as possible, so that nothing is overlooked. The PBS for ground systems at the Kennedy Space Center is being developed to encompass the traditional requirements including the alignment of facility, systems, and components to the organizational hierarchy. The Ground Operations Product Breakdown Structure is a hybrid in nature in that some aspects of a work breakdown structure will be incorporated and merged with the Architecture Concept of Operations, Master Subsystem List, customer interface, and assigned management responsibility. The Ground Operations Product Breakdown Structure needs to be able to identify the flexibility of support differing customers (internal and external) usage of ground support equipment within the Kennedy Space Center launch and processing complex. The development of the Product Breakdown Structure is an iterative activity Initially documenting the organization hierarchy structure and relationships. The Product Breakdown Structure identifies the linkage between the customer program requirements, allocation of system resources, development of design goals, and identification logistics products. As the Product Breakdown Structure progresses the incorporation of the results of requirement planning for the customer occurs identifying facility needs and systems. The mature Product Breakdown Structure is baselined with a hierarchical drawing, the Product Breakdown Structure database, and an associated document identifying the verification of the data through the life cycle of the program/product line. This paper will document, demonstrate, and identify key aspects of the life cycle of a Hybrid Product

  15. Structural and electronic properties of hybrid silicon-germanium nanosheets

    Directory of Open Access Journals (Sweden)

    F. L. Pérez Sánchez

    2014-12-01

    Full Text Available Using first principles molecular calculations, based on the Density Functional Theory (DFT, structural and electronic properties of hybrid graphene—like silicon—germanium circular nanosheets of hexagonal symmetry are investigated. The exchange—correlation functional of Perdew—Wang (PW in the local spin density approximation (LSDA based on the pseudopotentials of Dolg—Bergnre is applied. The finite extension nanosheets are represented by the CnHm—like cluster model with mono—hydrogenated armchair edges. Changes of the physicochemical properties were analyzed to learn on the chemical composition. We have obtained that the corrugation of the hybrid nanosheets is maintained (with respect to the pristine nanosheets of Ge and Si and is more pronounced when there is a high percentage of germanium. Moreover, hybrid nanosheets have ionic bonds (polarity in the interval from 0.18 to 0.77 D and exhibit a semimetal behavior. Three types of chemical compositions are considered: 1 the one—one relationship, 2 formation of Ge dimers and 3 formation of Ge hexagons. In each case it is observed an increase in the chemical reactivity. Finally, analyzing the work function we conclude that in cases 1 and 2 the chemical compositions improve the efficiency of the field emission and thereby they could expand the scope of nanotechnology applications.

  16. In Situ Production of Graphene-Fiber Hybrid Structures

    DEFF Research Database (Denmark)

    Akia, Mandana; Cremar, Lee; Chipara, Mircea

    2017-01-01

    fiber into another forming a continuous surface. The graphene-fiber hybrid structures are produced in situ from aqueous poly(vinyl alcohol) solutions. The solutions were subjected to centrifugal spinning to produce fine nanofiber mats. The addition of salt to the polymer solution stimulated...... a capillarity effect that promoted the formation of thin veils, which become graphene sheets upon dehydration by sulfuric acid vapor followed by carbonization (at relatively low temperatures, below 800 °C). These veils extend over several micrometers within the pores of the fiber network, and consist...

  17. Self-Biased Hybrid Piezoelectric-Photoelectrochemical Cell with Photocatalytic Functionalities.

    Science.gov (United States)

    Tan, Chuan Fu; Ong, Wei Li; Ho, Ghim Wei

    2015-07-28

    Utilizing solar energy for environmental and energy remediations based on photocatalytic hydrogen (H2) generation and water cleaning poses great challenges due to inadequate visible-light power conversion, high recombination rate, and intermittent availability of solar energy. Here, we report an energy-harvesting technology that utilizes multiple energy sources for development of sustainable operation of dual photocatalytic reactions. The fabricated hybrid cell combines energy harvesting from light and vibration to run a power-free photocatalytic process that exploits novel metal-semiconductor branched heterostructure (BHS) of its visible light absorption, high charge-separation efficiency, and piezoelectric properties to overcome the aforementioned challenges. The desirable characteristics of conductive flexible piezoelectrode in conjunction with pronounced light scattering of hierarchical structure originate intrinsically from the elaborate design yet facile synthesis of BHS. This self-powered photocatalysis system could potentially be used as H2 generator and water treatment system to produce clean energy and water resources.

  18. Structure of Solvent-Free Nanoparticle−Organic Hybrid Materials

    KAUST Repository

    Yu, Hsiu-Yu

    2010-11-16

    We derive the radial distribution function and the static structure factor for the particles in model nanoparticleorganic hybrid materials composed of nanoparticles and attached oligomeric chains in the absence of an intervening solvent. The assumption that the oligomers form an incompressible fluid of bead-chains attached to the particles that is at equilibrium for a given particle configuration allows us to apply a density functional theory for determining the equilibrium configuration of oligomers as well as the distribution function of the particles. A quasi-analytic solution is facilitated by a regular perturbation analysis valid when the oligomer radius of gyration R g is much greater than the particle radius a. The results show that the constraint that each particle carries its own share of the fluid attached to itself yields a static structure factor that approaches zero as the wavenumber approaches zero. This result indicates that each particle excludes exactly one other particle from its neighborhood. © 2010 American Chemical Society.

  19. Application of Metal-Semiconductor-Metal (MSM) Photodetectors for Transverse and Longitudinal Intra-Bunch Beam Diagnostics

    CERN Document Server

    Steinhagen, R J; Boland, M J; Lucas, T G; Rassool, R P

    2013-01-01

    The performance reach of modern accelerators is often governed by the ability to reliably measure and control the beam stability. In high-brightness lepton and high-energy hadron accelerators, the use of optical diagnostic techniques is becoming more widespread as the required bandwidth, resolution and high RF beam power level involved limit the use of traditional electro-magnetic RF pick-up based methods. This contribution discusses the use of fibre-coupled ultra-fast Metal-Semiconductor-Metal Photodetectors (MSM-PD) as an alternative, dependablemeans to measure signals derived from electro-optical and synchrotron-light based diagnostics systems. It describes the beam studies performed at CERN’s CLIC Test Facility (CTF3) and the Australian Synchrotron to assess the feasibility of this technology as a robust, wide-band and sensitive technique for measuring transverse intra-bunch and bunch-by-bunch beam oscillations, longitudinal beam profiles, un-bunched beam population and beam-halo profiles. The amplifica...

  20. CdSe Nanowire-Based Flexible Devices: Schottky Diodes, Metal-Semiconductor Field-Effect Transistors, and Inverters.

    Science.gov (United States)

    Jin, Weifeng; Zhang, Kun; Gao, Zhiwei; Li, Yanping; Yao, Li; Wang, Yilun; Dai, Lun

    2015-06-24

    Novel CdSe nanowire (NW)-based flexible devices, including Schottky diodes, metal-semiconductor field-effect transistors (MESFETs), and inverters, have been fabricated and investigated. The turn-on voltage of a typical Schottky diode is about 0.7 V, and the rectification ratio is larger than 1 × 10(7). The threshold voltage, on/off current ratio, subthreshold swing, and peak transconductance of a typical MESFET are about -0.3 V, 4 × 10(5), 78 mV/dec, and 2.7 μS, respectively. The inverter, constructed with two MESFETs, exhibits clear inverting behavior with the gain to be about 28, 34, and 38, at the supply voltages (V(DD)) of 3, 5, and 7 V, respectively. The inverter also shows good dynamic behavior. The rising and falling times of the output signals are about 0.18 and 0.09 ms, respectively, under 1000 Hz square wave signals input. The performances of the flexible devices are stable and reliable under different bending conditions. Our work demonstrates these flexible NW-based Schottky diodes, MESFETs, and inverters are promising candidate components for future portable transparent nanoelectronic devices.

  1. MSM-Metal Semiconductor Metal Photo-detector Using Black Silicon Germanium (SiGe) for Extended Wavelength Near Infrared Detection

    Science.gov (United States)

    2012-09-01

    due to metal catalysis and wet etching. Using the blackened SiGe/Si, MSM photodiodes were fabricated and tested. The lowering of reflection using a...MSM- Metal Semiconductor Metal Photo-detector Using Black Silicon Germanium (SiGe) for Extended Wavelength Near Infrared Detection by Fred...Do not return it to the originator. Army Research Laboratory Adelphi, MD 20783-1197 ARL-TR-6176 September 2012 MSM- Metal

  2. Giant Magnetic Field Enhancement in Hybridized MIM Structures

    KAUST Repository

    Alrasheed, Salma

    2017-10-23

    We propose numerically an approach to narrow the plasmon linewidth and enhance the magnetic near field intensity at a magnetic hot spot in a hybridized metal-insulatormetal (MIM) structure. First we insert in part of the dielectric layer of the MIM, at its center, another dielectric material of a high refractive index (HRI). This results in an increase in the magnetic near field enhancement of the magnetic plasmon (MP) resonance by 82% compared with the MIM without the HRI material. We then couple this enhanced MP resonance to a propagating surface plasmon polariton (SPP) to achieve a further enhancement of 438%. The strong coupling between the MP and the SPP is demonstrated by the large anti-crossing in the reflection spectra. The resulting maximum magnetic field enhancement at the gap is ~ |H / Hi|² = 3555.

  3. Long range energy transfer in graphene hybrid structures

    International Nuclear Information System (INIS)

    Gonçalves, Hugo; Bernardo, César; Moura, Cacilda; Belsley, Michael; Schellenberg, Peter; Ferreira, R A S; André, P S; Stauber, Tobias

    2016-01-01

    In this work we quantify the distance dependence for the extraction of energy from excited chromophores by a single layer graphene flake over a large separation range. To this end hybrid structures were prepared, consisting of a thin (2 nm) layer of a polymer matrix doped with a well chosen strongly fluorescent organic molecule, followed by an un-doped spacer layer of well-defined thicknesses made of the same polymer material and an underlying single layer of pristine, undoped graphene. The coupling strength is assessed through the variation of the fluorescence decay kinetics as a function of distance between the graphene and the excited chromophore molecules. Non-radiative energy transfer to the graphene was observed at distances of up to 60 nm; a range much greater than typical energy transfer distances observed in molecular systems. (paper)

  4. Novel thermal management structures and their applications in new hybrid technologies and feed-through structures

    International Nuclear Information System (INIS)

    Carter, A.A.; Oliveira, R. de; Gandi, A.

    1999-01-01

    Novel techniques are described for fabricating a new thermal management structure (TMS), in the form of rigid low-mass structures with extremely high in-plane thermal conductivity. The core materials can be forms of thermally anisotropically conducting pyrolytic graphite that are directly encapsulated in a new thin-layering process. The structures can be used in a large variety of applications, including: (a) Efficient interfacing with ceramic materials and metals to provide new thermal management technologies. (b) Providing the source for a new hybrid technology where low-mass custom-designed multilayer thin-film circuits can be directly processed onto such structures. Alternatively, having been prefabricated on an independent substrate, hybrids can be efficiently interfaced to such thermal management structures. (c) Providing electrical connectivity between both sides of a TMS board through a new feedthrough technology that allows the fabrication of both single-sided and double-sided hybrids. These thermal management techniques and their applications are the subject of an international patent application number PCT/GB99/02180, filed in the names of the European Organization for Nuclear Research and Queen Mary and Westfield College, London. (orig.)

  5. Switching Plasmons: Gold Nanorod-Copper Chalcogenide Core-Shell Nanoparticle Clusters with Selectable Metal/Semiconductor NIR Plasmon Resonances.

    Science.gov (United States)

    Muhammed, Madathumpady Abubaker Habeeb; Döblinger, Markus; Rodríguez-Fernández, Jessica

    2015-09-16

    Exerting control over the near-infrared (NIR) plasmonic response of nanosized metals and semiconductors can facilitate access to unexplored phenomena and applications. Here we combine electrostatic self-assembly and Cd(2+)/Cu(+) cation exchange to obtain an anisotropic core-shell nanoparticle cluster (NPC) whose optical properties stem from two dissimilar plasmonic materials: a gold nanorod (AuNR) core and a copper selenide (Cu(2-x)Se, x ≥ 0) supraparticle shell. The spectral response of the AuNR@Cu2Se NPCs is governed by the transverse and longitudinal plasmon bands (LPB) of the anisotropic metallic core, since the Cu2Se shell is nonplasmonic. Under aerobic conditions the shell undergoes vacancy doping (x > 0), leading to the plasmon-rich NIR spectrum of the AuNR@Cu(2-x)Se NPCs. For low vacancy doping levels the NIR optical properties of the dually plasmonic NPCs are determined by the LPBs of the semiconductor shell (along its major longitudinal axis) and of the metal core. Conversely, for high vacancy doping levels their NIR optical response is dominated by the two most intense plasmon modes from the shell: the transverse (along the shortest transversal axis) and longitudinal (along the major longitudinal axis) modes. The optical properties of the NPCs can be reversibly switched back to a purely metallic plasmonic character upon reversible conversion of AuNR@Cu(2-x)Se into AuNR@Cu2Se. Such well-defined nanosized colloidal assemblies feature the unique ability of holding an all-metallic, a metallic/semiconductor, or an all-semiconductor plasmonic response in the NIR. Therefore, they can serve as an ideal platform to evaluate the crosstalk between plasmonic metals and plasmonic semiconductors at the nanoscale. Furthermore, their versatility to display plasmon modes in the first, second, or both NIR windows is particularly advantageous for bioapplications, especially considering their strong absorbing and near-field enhancing properties.

  6. Gate-voltage control of equal-spin Andreev reflection in half-metal/semiconductor/superconductor junctions

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Xiuqiang, E-mail: xianqiangzhe@126.com [National Laboratory of Solid State Microstructures and Department of Physics, Nanjing University, Nanjing 210093 (China); Meng, Hao, E-mail: menghao1982@shu.edu.cn [School of Physics and Telecommunication Engineering, Shanxi University of Technology, Hanzhong 723001 (China)

    2016-04-22

    With the Blonder–Tinkham–Klapwijk (BTK) approach, we investigate conductance spectrum in Ferromagnet/Semiconductor/Superconductor (FM/Sm/SC) double tunnel junctions where strong Rashba spin–orbit interaction (RSOI) is taken into account in semiconductors. For the half-metal limit, we find that the in-gap conductance becomes finite except at zero voltage when inserting a ferromagnetic insulator (FI) at the Sm/SC interface, which means that the appearance of a long-range triplet states in the half-metal. This is because of the emergence of the unconventional equal-spin Andreev reflection (ESAR). When the FI locates at the FM/Sm interface, however, we find the vanishing in-gap conductance due to the absence of the ESAR. Moreover, the non-zero in-gap conductance shows a nonmonotonic dependence on RSOI which can be controlled by applying an external gate voltage. Our results can be used to generate and manipulate the long-range spin triplet correlation in the nascent field of superconducting spintronics. - Highlights: • We study the equal-spin Andreev reflection in half-metal/semiconductor/superconductor (HM/Sm/SC) junctions. • The equal-spin Andreev reflection appearance when inserting a ferromagnetic insulator at the Sm/SC interface. • The finite in-gap conductance is attributed to the emergence of the equal-spin Andreev reflection. • The finite in-gap conductance shows a nonmonotonic dependence on Rashba spin–orbit interaction. • The finite in-gap conductance can be controlled by applying an external gate voltage.

  7. Efficient, Broadband and Wide-Angle Hot-Electron Transduction using Metal-Semiconductor Hyperbolic Metamaterials

    KAUST Repository

    Sakhdari, Maryam

    2016-05-20

    Hot-electron devices are emerging as promising candidates for the transduction of optical radiation into electrical current, as they enable photodetection and solar/infrared energy harvesting at sub-bandgap wavelengths. Nevertheless, poor photoconversion quantum yields and low bandwidth pose fundamental challenge to fascinating applications of hot-electron optoelectronics. Based on a novel hyperbolic metamaterial (HMM) structure, we theoretically propose a vertically-integrated hot-electron device that can efficiently couple plasmonic excitations into electron flows, with an external quantum efficiency approaching the physical limit. Further, this metamaterial-based device can have a broadband and omnidirectional response at infrared and visible wavelengths. We believe that these findings may shed some light on designing practical devices for energy-efficient photodetection and energy harvesting beyond the bandgap spectral limit.

  8. Structural Transformations in Nematic Liquid Crystals with a Hybrid Orientation

    Science.gov (United States)

    Delev, V. A.; Krekhov, A. P.

    2017-12-01

    The structural transformations in a nematic liquid crystal (NLC) layer with a hybrid orientation (planar director orientation is created on one substrate and homeotropic director orientation is created on the other) are studied. In the case of a dc voltage applied to the NLC layer, the primary instability is flexoelectric. It causes the appearance of flexoelectric domains oriented along the director on the substrate with a planar orientation. When the voltage increases further, an electroconvective instability in the form of rolls moving almost normal to flexoelectric domains develops along with these domains. Thus, the following spatially periodic structures of different natures coexist in one system: equilibrium static flexoelectric deformation of a director and dissipative moving oblique electroconvection rolls. The primary instability in the case of an ac voltage is represented by electroconvection, which leads to moving oblique or normal rolls depending on the electric field frequency. Above the electroconvection threshold, a transition to moving "abnormal" rolls is detected. The wavevector of the rolls coincides with the initial director orientation on the substrate with a planar orientation, and the projection of the director at the midplane of the NLC layer on the layer plane makes a certain angle with the wavevector. The results of numerical calculations of the threshold characteristics of the primary instabilities agree well with the obtained experimental data.

  9. Wetting properties of hybrid structure with hydrophilic ridges and hydrophobic channels

    Science.gov (United States)

    Lee, Dong-Ki; Choi, Su Young; Park, Min Soo; Cho, Young Hak

    2018-02-01

    In the present study, we fabricated a hybrid structure where the upper surface of the ridge is hydrophilic and the inner surface of the channel is hydrophobic. Laser-induced backside wet etching (LIBWE) process was performed to machine the hybrid structure on a Pyrex glass substrate. Wetting properties were evaluated from static contact angles (CAs) measurement in parallel and orthogonal directions. The water droplet on the hybrid structure was in the Cassie-Baxter state and showed anisotropic wetting property along groove lines. Moisture condensation studies under humid condition indicated that water droplets grew and coalesced on the ridge with hydrophilicity. Furthermore, water-oil separation was tested using a microfluidic chip with the developed hybrid structure. In case of hybrid microfluidic chip, the water could not flow into channel but the hexadecane could flow due to the capillary pressure difference.

  10. Hybrid Structured Illumination Expansion Microscopy Reveals Microbial Cytoskeleton Organization.

    Science.gov (United States)

    Halpern, Aaron R; Alas, Germain C M; Chozinski, Tyler J; Paredez, Alexander R; Vaughan, Joshua C

    2017-12-26

    Recently developed tissue-hydrogel methods for specimen expansion now enable researchers to perform super-resolution microscopy with ∼65 nm lateral resolution using ordinary microscopes, standard fluorescent probes, and inexpensive reagents. Here we use the combination of specimen expansion and the optical super-resolution microscopy technique structured illumination microscopy (SIM) to extend the spatial resolution to ∼30 nm. We apply this hybrid method, which we call ExSIM, to study the cytoskeleton of the important human pathogen Giardia lamblia including the adhesive disc and flagellar axonemes. We determined the localization of two recently identified disc-associated proteins, including DAP86676 , which localizes to disc microribbons, and the functionally unknown DAP16263 , which primarily localizes to dorsal microtubules of the disc overlap zone and the paraflagellar rod of ventral axonemes. Based on its strong performance in revealing known and unknown details of the ultrastructure of Giardia, we find that ExSIM is a simple, rapid, and powerful super-resolution method for the study of fixed specimens, and it should be broadly applicable to other biological systems of interest.

  11. Tunneling conductance in semiconductor-superconductor hybrid structures

    Science.gov (United States)

    Stenger, John; Stanescu, Tudor D.

    2017-12-01

    We study the differential conductance for charge tunneling into a semiconductor wire-superconductor hybrid structure, which is actively investigated as a possible scheme for realizing topological superconductivity and Majorana zero modes. The calculations are done based on a tight-binding model of the heterostructure using both a Blonder-Tinkham-Klapwijk approach and a Keldysh nonequilibrium Green's function method. The dependence of various tunneling conductance features on the coupling strength between the semiconductor and the superconductor, the tunnel barrier height, and temperature is systematically investigated. We find that treating the parent superconductor as an active component of the system, rather than a passive source of Cooper pairs, has qualitative consequences regarding the low-energy behavior of the differential conductance. In particular, the presence of subgap states in the parent superconductor, due to disorder and finite magnetic fields, leads to characteristic particle-hole asymmetric features and to the breakdown of the quantization of the zero-bias peak associated with the presence of Majorana zero modes localized at the ends of the wire. The implications of these findings for the effort toward the realization of Majorana bound states with true non-Abelian properties are discussed.

  12. Hybrid Composites for LH2 Fuel Tank Structure

    Science.gov (United States)

    Grimsley, Brian W.; Cano, Roberto J.; Johnston, Norman J.; Loos, Alfred C.; McMahon, William M.

    2001-01-01

    The application of lightweight carbon fiber reinforced plastics (CFRP) as structure for cryogenic fuel tanks is critical to the success of the next generation of Reusable Launch Vehicles (RLV). The recent failure of the X-33 composite fuel tank occurred in part due to microcracking of the polymer matrix, which allowed cryogen to permeate through the inner skin to the honeycomb core. As part of an approach to solve these problems, NASA Langley Research Center (LaRC) and Marshall Space Flight Center (MSFC) are working to develop and investigate polymer films that will act as a barrier to the permeation of LH2 through the composite laminate. In this study two commercially available films and eleven novel LaRC films were tested in an existing cryogenics laboratory at MSFC to determine the permeance of argon at room temperature. Several of these films were introduced as a layer in the composite to form an interleaved, or hybrid, composite to determine the effects on permeability. In addition, the effects of the interleaved layer thickness, number, and location on the mechanical properties of the composite laminate were investigated. In this initial screening process, several of the films were found to exhibit lower permeability to argon than the composite panels tested.

  13. Hybrid Spintronic Structures With Magnetic Oxides and Heusler Alloys

    DEFF Research Database (Denmark)

    Xu, Y. B.; Hassan, S. S. A.; Wong, P. K. J.

    2008-01-01

    Hybrid spintronic structures, integrating half-metallic magnetic oxides and Heusler alloys with their predicted high spin polarization, are important for the development of second-generation spintronics with high-efficient spin injection. We have synthesized epitaxial magnetic oxide Fe3O4 on Ga......As(100) and the unit cell of the Fe3O4 was found to be rotated by 45 degrees to match the gallium arsenide GaAs. The films were found to have a bulk-like moment down to 3-4 nm and a low coercivity indicating a high-quality magnetic interface. The magnetization hysteresis loops of the ultrathin films...... are controlled by uniaxial magnetic anisotropy. The dynamic response of the sample shows a heavily damped precessional response to the applied field pulses. In the Heusler alloy system of Co-2 MnGa on GaAs, we found that the magnetic moment was reduced for thicknesses down to 10 nm, which may account...

  14. Enhanced electrical transparency by ultra-thin LaAlO3 insertion at oxide metal/semiconductor heterointerfaces

    Energy Technology Data Exchange (ETDEWEB)

    Yajima, Takeaki [SLAC National Accelerator Lab., Menlo Park, CA (United States); The Univ. of Tokyo, Tokyo (Japan); Minohara, Makoto [SLAC National Accelerator Lab., Menlo Park, CA (United States); Stanford Univ., Stanford, CA (United States); Bell, Christopher [SLAC National Accelerator Lab., Menlo Park, CA (United States); ; Kumigashira, Hiroshi [Stanford Univ., Stanford, CA (United States); Oshima, Masaharu [The Univ. of Tokyo, Tokyo (Japan); Hwang, Harold Y. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Stanford Univ., Stanford, CA (United States); Hikita, Yasuyuki [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2015-02-05

    We demonstrate that the electrical conductivity of metal/semiconductor oxide heterojunctions can be increased over 7 orders of magnitude by inserting an ultrathin layer of LaAlO3. This counterintuitive result, that an interfacial barrier can be driven transparent by inserting a wide-gap insulator, arises from the large internal electric field between the two polar LaAlO3 surfaces. In conclusion, this field modifies the effective band offset in the device, highlighting the ability to design the electrostatic boundary conditions with atomic precision.

  15. The hybrid thermography approach applied to architectural structures

    Science.gov (United States)

    Sfarra, S.; Ambrosini, D.; Paoletti, D.; Nardi, I.; Pasqualoni, G.

    2017-07-01

    This work contains an overview of infrared thermography (IRT) method and its applications relating to the investigation of architectural structures. In this method, the passive approach is usually used in civil engineering, since it provides a panoramic view of the thermal anomalies to be interpreted also thanks to the use of photographs focused on the region of interest (ROI). The active approach, is more suitable for laboratory or indoor inspections, as well as for objects having a small size. The external stress to be applied is thermal, coming from non-natural apparatus such as lamps or hot / cold air jets. In addition, the latter permits to obtain quantitative information related to defects not detectable to the naked eyes. Very recently, the hybrid thermography (HIRT) approach has been introduced to the attention of the scientific panorama. It can be applied when the radiation coming from the sun, directly arrives (i.e., possibly without the shadow cast effect) on a surface exposed to the air. A large number of thermograms must be collected and a post-processing analysis is subsequently applied via advanced algorithms. Therefore, an appraisal of the defect depth can be obtained passing through the calculation of the combined thermal diffusivity of the materials above the defect. The approach is validated herein by working, in a first stage, on a mosaic sample having known defects while, in a second stage, on a Church built in L'Aquila (Italy) and covered with a particular masonry structure called apparecchio aquilano. The results obtained appear promising.

  16. A Hybrid Structure for Data Aggregation in Wireless Sensor Network

    Directory of Open Access Journals (Sweden)

    Hedieh Sajedi

    2014-01-01

    Full Text Available In recent years, wireless sensor networks have been used for various applications such as environmental monitoring, military and medical applications. A wireless sensor network uses a large number of sensor nodes that continuously collect and send data from a specific region to a base station. Data from sensors are collected from the study area in the common scenario of sensor networks. Afterward, sensed data is sent to the base station. However, neighboring sensors often lead to redundancy of data. Transmission of redundant data to the base station consumes energy and produces traffic, because process is run in a large network. Data aggregation was proposed in order to reduce redundancy in data transformation and traffic. The most popular communication protocol in this field is cluster based data aggregation. Clustering causes energy balance, but sometimes energy consumption is not efficient due to the long distance between cluster heads and base station. In another communication protocol, which is based on a tree construction, because of the short distance between the sensors, energy consumption is low. In this data aggregation approach, since each sensor node is considered as one of the vertices of a tree, the depth of tree is usually high. In this paper, an efficient hierarchical hybrid approach for data aggregation is presented. It reduces energy consumption based on clustering and minimum spanning tree. The benefit of combining clustering and tree structure is reducing the disadvantages of previous structures. The proposed method firstly employs clustering algorithm and then a minimum spanning tree is constructed based on cluster heads. Our proposed method was compared to LEACH which is a well-known data aggregation method in terms of energy consumption and the amount of energy remaining in each sensor network lifetime. Simulation results indicate that our proposed method is more efficient than LEACH algorithm considering energy

  17. Hybrid Nanocomposites for Efficient Aerospace Structures, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA's Advanced Air Vehicles program seeks to improve safety and efficiency through exploration of the value of hybrid composites, guiding utilization of the...

  18. Hybrid Nanocomposites for Efficient Aerospace Structures, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA seeks to address the primary goals of the Advanced Air Vehicles program, improving safety and efficiency, through exploration of the value for hybrid composites...

  19. Extraordinary Magnetoresistance Effect in Semiconductor/Metal Hybrid Structure

    KAUST Repository

    Sun, Jian

    2013-06-27

    In this dissertation, the extraordinary magnetoresistance (EMR) effect in semiconductor/metal hybrid structures is studied to improve the performance in sensing applications. Using two-dimensional finite element simulations, the geometric dependence of the output sensitivity, which is a more relevant parameter for EMR sensors than the magnetoresistance (MR), is studied. The results show that the optimal geometry in this case is different from the geometry reported before, where the MR ratio was optimized. A device consisting of a semiconductor bar with length/width ratio of 5~10 and having only 2 contacts is found to exhibit the highest sensitivity. A newly developed three-dimensional finite element model is employed to investigate parameters that have been neglected with the two dimensional simulations utilized so far, i.e., thickness of metal shunt and arbitrary semiconductor/metal interface. The simulations show the influence of those parameters on the sensitivity is up to 10 %. The model also enables exploring the EMR effect in planar magnetic fields. In case of a bar device, the sensitivity to planar fields is about 15 % to 20 % of the one to perpendicular fields. 5 A “top-contacted” structure is proposed to reduce the complexity of fabrication, where neither patterning of the semiconductor nor precise alignment is required. A comparison of the new structure with a conventionally fabricated device shows that a similar magnetic field resolution of 24 nT/√Hz is obtained. A new 3-contact device is developed improving the poor low-field sensitivity observed in conventional EMR devices, resulting from its parabolic magnetoresistance response. The 3-contact device provides a considerable boost of the low field response by combining the Hall effect with the EMR effect, resulting in an increase of the output sensitivity by 5 times at 0.01 T compared to a 2-contact device. The results of this dissertation provide new insights into the optimization of EMR devices

  20. The Effectiveness of Hybrid Structure in Overcoming Coastal Abration in Trimulyo, Genuk Subdistrict Semarang City

    Science.gov (United States)

    Kurnia, Domas; Nugroho, Denny

    2018-02-01

    Trimulyo is one of coastal village in Genuk Subdistrict, Semarang City which now facing serious coastal abrasion. Such a thing has been causing loss of ponds and settlements. One of solution which currently carried is hybrid structure which combining permeable structure to break up the waves and trap sediment. The hybrid structure is designed as agitation dredging, which increase suspended sediment in sea water. The goals of this research were to studying the effectiveness of hybrid structure in handling coastal abration and to counting the volume of sedimentation during 20 months as well as rate of sedimentation. To reach the goals, high resolution satellite imagery year 2015 and 2016, scaled stick and sediment trap were applied to the study. Image processing was conducted by using Arc GIS 10.3 software. The effectiveness of hybrid structured was determined by series of field survey of existing condition. Rate of sedimentation measured during before and after hybrid structure built (20 months). The results showed that hybrid structure was effective to reduce coastal abrasion, it proven by a large amount of sediment was trapped behind the structure and coastline was upward along 170 meter since it was built. The volume of sediment during 20 months is 81.500 m3. If it assumed that the rate of sedimentation constantly, monthly rate of sedimentation is 4.075 m3/month or daily rate is 135,8 m3/day. The sediment that has formed highly recommended to use as mangrove conservation area in Semarang City.

  1. On the structural and physicochemical properties of gamma irradiated UHMWPE/silane hybrid

    International Nuclear Information System (INIS)

    Shafiq, Muhammad; Mehmood, Malik Sajjad; Yasin, Tariq

    2013-01-01

    This study has been carried to investigate the influence of gamma rays on the structural and physicochemical properties of UHMWPE/silane hybrid. UHMWPE was mixed with vinyltriethoxysilane (VTES) and compression molded sheets were irradiated at different doses of gamma rays. Fourier transform infrared spectroscopy indicated the formation of siloxane linkages in hybrids, which were found to be shifted towards lower wave number upon irradiation. The X-ray diffraction patterns showed significant increase in the percentage crystallinity of hybrid upon gamma irradiation, especially at 65 kGy absorbed dose. Scanning electron micrographs showed good consolidation and compaction with no surface defects. Moreover, the rough topography was changed to smooth ripple-like appearance upon γ-irradiation. Thermal analysis revealed that irradiated hybrids exhibited higher onset thermal degradation temperature, peak melting temperature, and crystalline lamellae thickness compared with the water treated hybrid. In addition, the tensile testing confirmed an increase of 41% and 133% in yield strength and Young's modulus in 100 kGy irradiated hybrid respectively than that of water treated hybrid. We hope that the irradiated UHMWPE/silane hybrids can be used in various high-strength applications such as total joint replacements, pickers for textile machinery, lining for coal chutes and dump trucks. - Highlights: • UHMWPE/silane hybrids have been prepared and irradiated using gamma rays. • The structural analysis revealed the formation siloxane linkages in the hybrid. • The crystallinity, thermal stability and mechanical properties of hybrids were improved with irradiation. • The irradiated hybrids can be used in various high-strength applications

  2. The dynamics of the laser-induced metal-semiconductor phase transition of samarium sulfide (SmS); Die Dynamik des laserinduzierten Metall-Halbleiter-Phasenuebergangs von Samariumsulfid (SmS)

    Energy Technology Data Exchange (ETDEWEB)

    Kaempfer, Tino

    2009-12-15

    The present thesis is dedicated to the experimental study of the metal-semiconductor phase transition of samarium sulfide (SmS): Temperature- and time-resolved experiments on the characterization of the phase transition of mixed-valence SmS samples (M-SmS) are presented. The measurement of the dynamics of the laser-induced phase transition pursues via time-resolved ultrashort-time microscopy and by X-ray diffraction with sub-picosecond time resolution. The electronic and structural processes, which follow an excitation of M-SmS with infrared femtosecond laser pulses, are physically interpreted on the base of the results obtained in this thesis and model imaginations. [German] Die vorliegende Arbeit ist der experimentellen Untersuchung des Metall-Halbleiter-Phasenuebergangs von Samariumsulfid (SmS) gewidmet. Es werden temperatur- und zeitaufgeloeste Experimente zur Charakterisierung des Phasenuebergangs gemischt-valenter SmS Proben (M-SmS) vorgestellt. Die Messung der Dynamik des laserinduzierten Phasenuebergangs erfolgt ueber zeitaufgeloeste Ultrakurzzeit-Mikroskopie und durch Roentgenbeugung mit subpikosekunden Zeitaufloesung. Die elektronischen und strukturellen Prozesse, welche einer Anregung von M-SmS mit infraroten Femtosekunden-Laserpulsen folgen, werden auf der Basis der in dieser Arbeit gewonnenen Ergebnisse und Modellvorstellungen physikalisch interpretiert. (orig.)

  3. Physical, structural and thermomechanical properties of oil palm nano filler/kenaf/epoxy hybrid nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Saba, N., E-mail: naheedchem@gmail.com [Laboratory of Biocomposite Technology, Institute of Tropical Forestry and Forest Products(INTROP), Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Paridah, M.T. [Laboratory of Biocomposite Technology, Institute of Tropical Forestry and Forest Products(INTROP), Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Abdan, K. [Department of Biological and Agricultural Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM Serdang Selangor (Malaysia); Ibrahim, N.A. [Department of Chemistry, Faculty of Science, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia)

    2016-12-01

    The present research study deals with the fabrication of kenaf/epoxy hybrid nanocomposites by the incorporation of oil palm nano filler, montmorillonite (MMT) and organically modified montmorillonite (OMMT) at 3% loading, through hand lay-up technique. Effect of adding different nano fillers on the physical (density), structural [X-ray diffraction (XRD)] and thermomechanical analysis (TMA) of kenaf/epoxy composites were carried out. Density results revealed that the incorporation of nano filler in the kenaf/epoxy composites increases the density which in turn increases the hardness of the hybrid nanocomposites. XRD analysis confirmed the presence of nano fillers in the structure of their respective fabricated hybrid nanocomposites. All hybrid nanocomposites displayed lower coefficient of thermal expansion (CTE) with respect to kenaf/epoxy composites. Overall results predicted that the properties improvement in nano OPEFB/kenaf/epoxy was quite comparable to MMT/kenaf/epoxy but relatively lesser to OMMT/kenaf/epoxy hybrid nanocomposites and higher with respect to kenaf/epoxy composites. The improvement ascribed due to improved interfacial bonding or cross linking between kenaf fibers and epoxy matrix by addition of nano filler. - Highlights: • Nano OPEFB/kenaf/epoxy hybrid nanocomposites were fabricated by hand lay-up. • Effect of nano OPEFB on density & structure of kenaf/epoxy were investigated. • Thermal expansion coefficients of kenaf/epoxy and hybrid nanocomposites evaluated. • Comparative studies were made with MMT and OMMT kenaf/epoxy hybrid nanocomposites.

  4. Physical, structural and thermomechanical properties of oil palm nano filler/kenaf/epoxy hybrid nanocomposites

    International Nuclear Information System (INIS)

    Saba, N.; Paridah, M.T.; Abdan, K.; Ibrahim, N.A.

    2016-01-01

    The present research study deals with the fabrication of kenaf/epoxy hybrid nanocomposites by the incorporation of oil palm nano filler, montmorillonite (MMT) and organically modified montmorillonite (OMMT) at 3% loading, through hand lay-up technique. Effect of adding different nano fillers on the physical (density), structural [X-ray diffraction (XRD)] and thermomechanical analysis (TMA) of kenaf/epoxy composites were carried out. Density results revealed that the incorporation of nano filler in the kenaf/epoxy composites increases the density which in turn increases the hardness of the hybrid nanocomposites. XRD analysis confirmed the presence of nano fillers in the structure of their respective fabricated hybrid nanocomposites. All hybrid nanocomposites displayed lower coefficient of thermal expansion (CTE) with respect to kenaf/epoxy composites. Overall results predicted that the properties improvement in nano OPEFB/kenaf/epoxy was quite comparable to MMT/kenaf/epoxy but relatively lesser to OMMT/kenaf/epoxy hybrid nanocomposites and higher with respect to kenaf/epoxy composites. The improvement ascribed due to improved interfacial bonding or cross linking between kenaf fibers and epoxy matrix by addition of nano filler. - Highlights: • Nano OPEFB/kenaf/epoxy hybrid nanocomposites were fabricated by hand lay-up. • Effect of nano OPEFB on density & structure of kenaf/epoxy were investigated. • Thermal expansion coefficients of kenaf/epoxy and hybrid nanocomposites evaluated. • Comparative studies were made with MMT and OMMT kenaf/epoxy hybrid nanocomposites.

  5. Optical Fiber/Nanowire Hybrid Structures for Efficient Three-Dimensional Dye-Sensitized Solar Cells

    KAUST Repository

    Weintraub, Benjamin

    2009-11-09

    Wired up: The energy conversion efficiency of three-dimensional dye-sensitized solar cells (DSSCs) in a hybrid structure that integrates optical fibers and nanowire arrays is greater than that of a two-dimensional device. Internal axial illumination enhances the energy conversion efficiency of a rectangular fiber-based hybrid structure (see picture) by a factor of up to six compared to light illumination normal to the fiber axis from outside the device.

  6. CVD growth of graphene under exfoliated hexagonal boron nitride for vertical hybrid structures

    International Nuclear Information System (INIS)

    Wang, Min; Jang, Sung Kyu; Song, Young Jae; Lee, Sungjoo

    2015-01-01

    Graphical abstract: We have demonstrated a novel yet simple method for fabricating graphene-based vertical hybrid structures by performing the CVD growth of graphene at an h-BN/Cu interface. Our systematic Raman measurements combined with plasma etching process indicate that a graphene film is grown under exfoliated h-BN rather than on its top surface, and that an h-BN/graphene vertical hybrid structure has been fabricated. Electrical transport measurements of this h-BN/graphene, transferred on SiO2, show the carrier mobility up to approximately 2250 cm 2 V −1 s −1 . The developed method would enable the exploration of the possibility of novel hybrid structure integration with two-dimensional material systems. - Abstract: We have demonstrated a novel yet simple method for fabricating graphene-based vertical hybrid structures by performing the CVD growth of graphene at an h-BN/Cu interface. Our systematic Raman measurements combined with plasma etching process indicate that a graphene film is grown under exfoliated h-BN rather than on its top surface, and that an h-BN/graphene vertical hybrid structure has been fabricated. Electrical transport measurements of this h-BN/graphene, transferred on SiO 2 , show the carrier mobility up to approximately 2250 cm 2 V −1 s −1 . The developed method would enable the exploration of the possibility of novel hybrid structure integration with two-dimensional material systems

  7. Structure and mechanical properties of a hybrid material with copper matrix and steel fibers after ECAP

    Science.gov (United States)

    Stanislav, Rogachev; Sergey, Nikulin; Vladimir, Khatkevich; Alexey, Molyarov; Alexander, Komissarov; Kseniya, Utkina

    2017-12-01

    The structure and mechanical properties of a hybrid material with a copper matrix and steel fibers subjected to ECAP were studied. C12200 pure copper and AISI 304 steel were used as hybrid material components. A mixed submicrocrystalline grain-subgrain structure with a high dislocation density is formed in the copper matrix of the hybrid material as a result of ECAP that leads to an increase in strength by ~20% while maintaining a high value of the relative elongation. The strength of the steel fibers of the hybrid material after ECAP was significantly increased primarily due to the process of intensive deformation twinning and increase in the dislocation density. At the same time, the presence of a ductile copper matrix around the steel fibers makes it difficult for them to shear strain during ECAP, which slows down the process of a developed ultrafine-grained structure formation.

  8. Hybrid structures based on montmorillonite/modified starch intercalate

    Czech Academy of Sciences Publication Activity Database

    Duchek, P.; Špírková, Milena

    2010-01-01

    Roč. 104, č. 9 (2010), s. 885 ISSN 0009-2770. [International Conference on Polysaccharides-Glycoscience /6./. 29.09.2010-1.10.2010, Praha] R&D Projects: GA AV ČR(CZ) IAAX08240901 Institutional research plan: CEZ:AV0Z40500505 Keywords : organic/inorganic hybrides * montmorillonite Subject RIV: JI - Composite Materials

  9. Storing in carbon nano structures for hybrid systems solar hydrogen

    International Nuclear Information System (INIS)

    Marazzi, R.; Zini, G.; Tartarini, P.

    2009-01-01

    We have developed a hybrid energy system for converting energy from renewable sources and its storage in the form of hydrogen. The storage uses activated carbon and the methodology was modelled mathematically and simulated in numerical software. The results show that storage compression is cheaper storage for liquefaction. [it

  10. The doubly conditioned frequency spectrum does not distinguish between ancient population structure and hybridization

    KAUST Repository

    Eriksson, Anders

    2014-03-13

    Distinguishing between hybridization and population structure in the ancestral species is a key challenge in our understanding of how permeable species boundaries are to gene flow. The doubly conditioned frequency spectrum (dcfs) has been argued to be a powerful metric to discriminate between these two explanations, and it was used to argue for hybridization between Neandertal and anatomically modern humans. The shape of the observed dcfs for these two species cannot be reproduced by a model that represents ancient population structure in Africa with two populations, while adding hybridization produces realistic shapes. In this letter, we show that this result is a consequence of the spatial coarseness of the demographic model and that a spatially structured stepping stone model can generate realistic dcfs without hybridization. This result highlights how inferences on hybridization between recently diverged species can be strongly affected by the choice of how population structure is represented in the underlying demographic model. We also conclude that the dcfs has limited power in distinguishing between the signals left by hybridization and ancient structure. 2014 The Author.

  11. Influence of the QD luminescence quantum yield on photocurrent in QD/graphene hybrid structures

    Science.gov (United States)

    Reznik, Ivan A.; Gromova, Yulia A.; Zlatov, Andrei S.; Baranov, Mikhail A.; Orlova, Anna O.; Moshkalev, Stanislav A.; Maslov, Vladimir G.; Baranov, Alexander V.; Fedorov, Anatoly V.

    2016-04-01

    Photoinduced changes in luminescent and photoelectrical properties of the hybrid structure based on CdSe/ZnS QDs and multilayer graphene nanobelts were studied. It was shown that an irradiation of the structures by 365 nm mercury line in doses up to 23 J led to growth of QD luminescent quantum yield and photocurrent in the QD/graphene structures. This confirms the proximity of the rates of the QD luminescence decay and energy/charge transfer from QDs to graphene, and opens an opportunity to photoinduced control of the photoelectric response of the graphene based hybrid structures with semiconductor quantum dots.

  12. A novel structure of permanent-magnet-biased radial hybrid magnetic bearing

    International Nuclear Information System (INIS)

    Sun Jinji; Fang Jiancheng

    2011-01-01

    The paper proposes a novel structure for a permanent-magnet-biased radial hybrid magnetic bearing. Based on the air gap between the rotor and stator of traditional radial hybrid magnetic bearings, a subsidiary air gap is first constructed between the permanent magnets and the inner magnetic parts. Radial magnetic bearing makes X and Y magnetic fields independent of each other with separate stator poles, and the subsidiary air gap makes control flux to a close loop. As a result, magnetic field coupling of the X and Y channels is decreased significantly by the radial hybrid magnetic bearing and makes it easier to design control systems. Then an external rotor structure is designed into the radial hybrid magnetic bearing. The working principle of the radial hybrid magnetic bearing and its mathematical model is discussed. Finally, a non-linear magnetic network method is proposed to analyze the radial hybrid magnetic bearing. Simulation results indicate that magnetic fields in the two channels of the proposed radial hybrid magnetic bearing decouple well from each other.

  13. Effect of selection on green pea hybrid population structure

    Directory of Open Access Journals (Sweden)

    В. М. Стригун

    2013-05-01

    Full Text Available The article features the results of variability study for one of the productivity characteristics in green pea, namely «number of seeds in the seedpod» for hybrid  populations and for the selections made thereof. Statistical methods of analysis have established the levels of variability for the characteristics in F2 original population , the impact of the selection completed within F2 onto the variability of F3 hybrid population. This shows the efficiency of repeated selection from F3 population and its impact onto the level of expersiioon of the characteristic being studied in the resulting F6 population. As a conclusion, a good time is set for practical breeding with the characteristic of «number of seeds in a seedpod» for  the selection, as well as for the methods for achieving its stable expression, that is to facilitate the decrease of durations and means for the tests conduct.

  14. Bloch-Surface-Polariton-Based Hybrid Nanowire Structure for Subwavelength, Low-Loss Waveguiding

    Directory of Open Access Journals (Sweden)

    Weijing Kong

    2018-03-01

    Full Text Available Surface plasmon polaritons (SPPs have been thoroughly studied in the past decades for not only sensing but also waveguiding applications. Various plasmonic device structures have been explored due to their ability to confine their optical mode to the subwavelength level. However, with the existence of metal, the large ohmic loss limits the propagation distance of the SPP and thus the scalability of such devices. Therefore, different hybrid waveguides have been proposed to overcome this shortcoming. Through fine tuning of the coupling between the SPP and a conventional waveguide mode, a hybrid mode could be excited with decent mode confinement and extended propagation distance. As an effective alternative of SPP, Bloch surface waves have been re-investigated more recently for their unique advantages. As is supported in all-dielectric structures, the optical loss for the Bloch surface wave is much lower, which stands for a much longer propagating distance. Yet, the confinement of the Bloch surface wave due to the reflections and refractions in the multilayer structure is not as tight as that of the SPP. In this work, by integrating a periodic multilayer structure that supports the Bloch surface wave with a metallic nanowire structure, a hybrid Bloch surface wave polariton could be excited. With the proposed hybrid nanowire structure, a hybrid mode is demonstrated with the deep subwavelength mode confinement and a propagation distance of tens of microns.

  15. Novel fabrication technique of hybrid structure lens array for 3D images

    Science.gov (United States)

    Lee, Junsik; Kim, Junoh; Kim, Cheoljoong; Shin, Dooseub; Koo, Gyohyun; Won, Yong Hyub

    2016-03-01

    Tunable liquid lens arrays can produce three dimensional images by using electrowetting principle that alters surface tensions by applying voltage. This method has advantages of fast response time and low power consumption. However, it is challenging to fabricate a high fill factor liquid lens array and operate three dimensional images which demand high diopter. This study describes a hybrid structure lens array which has not only a liquid lens array but a solid lens array. A concave-shape lens array is unavoidable when using only the liquid lens array and some voltages are needed to make the lens flat. By placing the solid lens array on the liquid lens array, initial diopter can be positive. To fabricate the hybrid structure lens array, a conventional lithographic process in semiconductor manufacturing is needed. A negative photoresist SU-8 was used as chamber master molds. PDMS and UV adhesive replica molding are done sequentially. Two immiscible liquids, DI water and dodecane, are injected in the fabricated chamber, followed by sealing. The fabricated structure has a 20 by 20 pattern of cylindrical shaped circle array and the aperture size of each lens is 1mm. The thickness of the overall hybrid structure is about 2.8mm. Hybrid structure lens array has many advantages. Solid lens array has almost 100% fill factor and allow high efficiency. Diopter can be increased by more than 200 and negative diopter can be shifted to the positive region. This experiment showed several properties of the hybrid structure and demonstrated its superiority.

  16. High temperature operation of n-AlGaN channel metal semiconductor field effect transistors on low-defect AlN templates

    Science.gov (United States)

    Muhtadi, S.; Hwang, S.; Coleman, A.; Asif, F.; Lunev, A.; Chandrashekhar, M. V. S.; Khan, A.

    2017-05-01

    We report room-temperature to 200 °C operation of n-Al0.65Ga0.35N channel metal semiconductor field effect transistors (MESFET) grown over high-quality AlN/sapphire templates. For this temperature range, the source-drain currents, threshold voltages, and dc-transconductance values remain nearly unchanged with an estimated field-effect mobility of ˜90 cm2/V-s at 200 °C and currents of >100 mA/mm. The analysis of the temperature dependent current-voltage characteristics of the gate-source Schottky barrier diode reveals that the leakage currents arise from Frenkel-Poole emission. The capacitance-voltage data show no hysteresis, indicating a high quality Schottky barrier interface. These MESFET's have excellent potential for use as a high temperature power electronic or a solar-blind ultraviolet sensing device.

  17. Nanoscale Structure of Self-Assembling Hybrid Materials of Inorganic and Electronically Active Organic Phases

    Energy Technology Data Exchange (ETDEWEB)

    Sofos, M.; Goswami, D.A. Stone D.K.; Okasinski, J.S.; Jin, H.; Bedzyk, M.J.; Stupp, S.I. (NWU)

    2008-10-06

    Hybrid materials with nanoscale structure that incorporates inorganic and organic phases with electronic properties offer potential in an extensive functional space that includes photovoltaics, light emission, and sensing. This work describes the nanoscale structure of model hybrid materials with phases of silica and electronically active bola-amphiphile assemblies containing either oligo(p-phenylene vinylene) or oligo(thiophene) segments. The hybrid materials studied here were synthesized by evaporation-induced self-assembly and characterized by X-ray scattering techniques. Grazing-incidence X-ray scattering studies of these materials revealed the formation of two-dimensional hexagonally packed cylindrical micelles of the organic molecules with diameters between 3.1 and 3.6 nm and cylindrical axes parallel to the surface. During the self-assembly process at low pH, the cylindrical aggregates of conjugated molecules become surrounded by silica giving rise to a hybrid structure with long-range order. Specular X-ray reflectivity confirmed the long-range periodicity of the hybrid films within a specific range of molar ratios of tetraethyl orthosilicate to cationic amphiphile. We did not observe any long-range ordering in fully organic analogues unless quaternary ammonium groups were replaced by tertiary amines. These observations suggest that charge screening in these biscationic conjugated molecules by the mineral phase is a key factor in the evolution of long range order in the self-assembling hybrids.

  18. Hybrid organic-inorganic materials based on hydroxyapatite structure

    Energy Technology Data Exchange (ETDEWEB)

    Moussa, Sana Ben; Bachouâ, Hassen [U.R. Matériaux et synthèse organique UR17ES31, Institut Préparatoire aux Etudes d’Ingénieur de Monastir, Université de Monastir, 5019 Monastir (Tunisia); Gruselle, Michel, E-mail: michel.gruselle@upmc.fr [Sorbonne Université, UPMC Univ Paris 06, CNRS, UMR 8232, Institut Parisien de Chimie Moléculaire, F-75005 Paris (France); Beaunier, Patricia [Sorbonne Université, UPMC Univ Paris 06, CNRS, UMR 7197, Laboratoire de Réactivité de Surface, F-75005 Paris (France); Flambard, Alexandrine [Sorbonne Université, UPMC Univ Paris 06, CNRS, UMR 8232, Institut Parisien de Chimie Moléculaire, F-75005 Paris (France); Badraoui, Béchir [U.R. Matériaux et synthèse organique UR17ES31, Institut Préparatoire aux Etudes d’Ingénieur de Monastir, Université de Monastir, 5019 Monastir (Tunisia)

    2017-04-15

    The present article details the formation of calcium hydroxyapatite synthesized by the hydrothermal way, in presence of glycine or sarcosine. The presence of these amino-acids during the synthetic processes reduces the crystalline growthing through the formation of hybrid organic-inorganic species The crystallite sizes are decreasing and the morphology is modified with the increase of the amino-acid concentration. - Graphical abstract: Formation of Ca carboxylate salt leading to the grafting of glycine and sarcosine on the Ca=Hap surface (R= H, CH3).

  19. Hybrid functionals and electronic structure of high-pressure phase of CdO

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, K.B.; Paliwal, U. [Department of Physics, M. L. Sukhadia University, Udaipur 313001 (India); Sharma, B.K. [Department of Physics, University of Rajasthan, Jaipur 302004 (India)

    2011-05-15

    The electronic band structure and density of states (DOS) of B2-phase cadmium oxide (CdO) are computed following the first-principles linear combination of atomic orbitals method applying the CRYSTAL code. The PBE correlation functional coupled with Becke's ansatz for exchange is considered for calculations. The electronic band structure and DOS are examined considering HF, B3LYP and hybrid schemes. Hybrid functionals are used with 25, 15, 10 and 5% mixing of Fock exchange with PBE-GGA. Depending on the correlation functionals, and different mixings in the hybrid schemes, B2-phase CdO may have an indirect positive band gap, a negative band gap or a zero gap. The effect of pd repulsion originating from pd hybridisation is visible in the calculated band structures. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. Photoelectric effect in surface-barrier structures

    International Nuclear Information System (INIS)

    Kononenko, V.K.; Tupenevich, P.A.

    1985-08-01

    Deviations from the Fowler law were observed when investigating photoelectric emission in p-type ZnTe surface-barrier structures. The revealed peculiarities of the structure photosensitivity spectrum are explained by the electron transitions involving surface states at the metal-semiconductor interface. (author)

  1. Characterizing the physical and genetic structure of the lodgepole pine × jack pine hybrid zone: mosaic structure and differential introgression.

    Science.gov (United States)

    Cullingham, Catherine I; James, Patrick M A; Cooke, Janice E K; Coltman, David W

    2012-12-01

    Understanding the physical and genetic structure of hybrid zones can illuminate factors affecting their formation and stability. In north-central Alberta, lodgepole pine (Pinus contorta Dougl. ex Loud. var. latifolia) and jack pine (Pinus banksiana Lamb) form a complex and poorly defined hybrid zone. Better knowledge of this zone is relevant, given the recent host expansion of mountain pine beetle into jack pine. We characterized the zone by genotyping 1998 lodgepole, jack pine, and hybrids from British Columbia, Alberta, Saskatchewan, Ontario, and Minnesota at 11 microsatellites. Using Bayesian algorithms, we calculated genetic ancestry and used this to model the relationship between species occurrence and environment. In addition, we analyzed the ancestry of hybrids to calculate the genetic contribution of lodgepole and jack pine. Finally, we measured the amount of gene flow between the pure species. We found the distribution of the pine classes is explained by environmental variables, and these distributions differ from classic distribution maps. Hybrid ancestry was biased toward lodgepole pine; however, gene flow between the two species was equal. The results of this study suggest that the hybrid zone is complex and influenced by environmental constraints. As a result of this analysis, range limits should be redefined.

  2. Strength analysis and modeling of hybrid composite-aluminum aircraft structures

    OpenAIRE

    Kapidzic, Zlatan

    2013-01-01

    The current trend in aircraft design is to increase the proportion of fiber composites in the structures. Since many primary parts also are constructed using metals, the number of hybrid metal-composite structures is increasing. Such structures have traditionally often been avoided as an option because of the lack of methodology to handle the mismatch between the material properties. Composite and metal properties differ with respect to: thermal expansion, failure mechanisms, plasticity, sens...

  3. Self-Consistent Hybrid Functional Calculations: Implications for Structural, Electronic, and Optical Properties of Oxide Semiconductors

    Science.gov (United States)

    Fritsch, Daniel; Morgan, Benjamin J.; Walsh, Aron

    2017-01-01

    The development of new exchange-correlation functionals within density functional theory means that increasingly accurate information is accessible at moderate computational cost. Recently, a newly developed self-consistent hybrid functional has been proposed (Skone et al., Phys. Rev. B 89:195112, 2014), which allows for a reliable and accurate calculation of material properties using a fully ab initio procedure. Here, we apply this new functional to wurtzite ZnO, rutile SnO2, and rocksalt MgO. We present calculated structural, electronic, and optical properties, which we compare to results obtained with the PBE and PBE0 functionals. For all semiconductors considered here, the self-consistent hybrid approach gives improved agreement with experimental structural data relative to the PBE0 hybrid functional for a moderate increase in computational cost, while avoiding the empiricism common to conventional hybrid functionals. The electronic properties are improved for ZnO and MgO, whereas for SnO2 the PBE0 hybrid functional gives the best agreement with experimental data.

  4. Plasmon-gating photoluminescence in graphene/GeSi quantum dots hybrid structures

    Science.gov (United States)

    Chen, Yulu; Wu, Qiong; Ma, Yingjie; Liu, Tao; Fan, Yongliang; Yang, Xinju; Zhong, Zhenyang; Xu, Fei; Lu, Jianping; Jiang, Zuimin

    2015-12-01

    The ability to control light-matter interaction is central to several potential applications in lasing, sensing, and communication. Graphene plasmons provide a way of strongly enhancing the interaction and realizing ultrathin optoelectronic devices. Here, we find that photoluminescence (PL) intensities of the graphene/GeSi quantum dots hybrid structures are saturated and quenched under positive and negative voltages at the excitation of 325 nm, respectively. A mechanism called plasmon-gating effect is proposed to reveal the PL dependence of the hybrid structures on the external electric field. On the contrary, the PL intensities at the excitation of 405 and 795 nm of the hybrid structures are quenched due to the charge transfer by tuning the Fermi level of graphene or the blocking of the excitons recombination by excitons separation effect. The results also provide an evidence for the charge transfer mechanism. The plasmon gating effect on the PL provides a new way to control the optical properties of graphene/QD hybrid structures.

  5. Effect of secondary structure on the thermodynamics and kinetics of PNA hybridization to DNA hairpins

    DEFF Research Database (Denmark)

    Kushon, S A; Jordan, J P; Seifert, J L

    2001-01-01

    The binding of a series of PNA and DNA probes to a group of unusually stable DNA hairpins of the tetraloop motif has been observed using absorbance hypochromicity (ABS), circular dichroism (CD), and a colorimetric assay for PNA/DNA duplex detection. These results indicate that both stable PNA...... structures in both target and probe molecules are shown to depress the melting temperatures and free energies of the probe-target duplexes. Kinetic analysis of hybridization yields reaction rates that are up to 160-fold slower than hybridization between two unstructured strands. The thermodynamic and kinetic...

  6. Effect of secondary structure on the thermodynamics and kinetics of PNA hybridization to DNA hairpins

    DEFF Research Database (Denmark)

    Kushon, S A; Jordan, J P; Seifert, J L

    2001-01-01

    structures in both target and probe molecules are shown to depress the melting temperatures and free energies of the probe-target duplexes. Kinetic analysis of hybridization yields reaction rates that are up to 160-fold slower than hybridization between two unstructured strands. The thermodynamic and kinetic......-DNA and DNA-DNA duplexes can be formed with these target hairpins, even when the melting temperatures for the resulting duplexes are up to 50 degrees C lower than that of the hairpin target. Both hairpin/single-stranded and hairpin/hairpin interactions are considered in the scope of these studies. Secondary...

  7. Novel Hybrid Polymeric and Inorganic Structures for Applications in Nanobiotechnology

    OpenAIRE

    Valdeperez Toledo, Daniel; Parak, Wolfgang J. (Prof. Dr.)

    2017-01-01

    This cumulative doctoral dissertation deals with the use of diverse polymers in different applications within nanoscience. The synthesis and characterization of several nano and microstructures is also explained, focusing on the later surface modification via the use of different polymers. Polymers are chemical compounds formed by the combination of several repeating structural units (monomers) in a process called polymerization. ...

  8. Designing CNC Knit for Hybrid Membrane And Bending Active Structures

    DEFF Research Database (Denmark)

    Tamke, Martin; Holden Deleuran, Anders; Gengnagel, Christoph

    2015-01-01

    specific properties and detailing. CNC knitting with high tenacity yarn enables this practice and offers an alternative to current woven membranes. The design and fabrication of an 8m high fabric tower through an interdisciplinary team of architects, structural and textile engineers, allowed to investigate...

  9. Novel Damage Detection Techniques for Structural Health Monitoring Using a Hybrid Sensor

    Directory of Open Access Journals (Sweden)

    Dengjiang Wang

    2016-01-01

    Full Text Available This study presents a technique for detecting fatigue cracks based on a hybrid sensor monitoring system consisting of a combination of intelligent coating monitoring (ICM and piezoelectric transducer (PZT sensors. An experimental procedure using this hybrid sensor system was designed to monitor the cracks generated by fatigue testing in plate structures. A probability of detection (POD model that quantifies the reliability of damage detection for a specific sensor or the nondestructive testing (NDT method was used to evaluate the weight factor for the ICM and PZT sensors. To estimate the uncertainty of model parameters in this study, the Bayesian method was employed. Realistic data from fatigue testing was used to validate the overall method, and the results show that the novel damage detection technique using a hybrid sensor can quantify fatigue cracks more accurately than results obtained by conventional sensor methods.

  10. Design, analysis, and testing of a hybrid scale structural dynamic model of a Space Station

    Science.gov (United States)

    Gronet, Marc J.; Crawley, Edward F.; Allen, Bradley R.

    1989-01-01

    The impracticality of testing the fully-assembled on-orbit configurations of future large erectable space platforms fosters an increased reliance on other means for verifying predicted structural dynamic performance. One option is scale modeling. This paper discusses the design of a hybrid scale dynamic test model of the Freedom Space Station and its associated suspension system. Hybrid scaling laws are reviewed, followed by scale factor trades, component design examples, and an analytical evaluation of the overall model fidelity. Component and subassembly test results from a six-bay hybrid scale model truss are presented. Potential interactions of gravity and the suspension system with the free-free dynamics of the scale model are investigated. Suspension system design parameters, such as the number, location, mass, and stiffness of the suspension devices are traded to minimize undesirable interactions and form the basis for an overall suspension system concept for the scale model.

  11. Proton Conduction in Sulfonated Organic-Inorganic Hybrid Monoliths with Hierarchical Pore Structure.

    Science.gov (United States)

    von der Lehr, Martin; Seidler, Christopher F; Taffa, Dereje H; Wark, Michael; Smarsly, Bernd M; Marschall, Roland

    2016-09-28

    Porous organic-inorganic hybrid monoliths with hierarchical porosity exhibiting macro- and mesopores are prepared via sol-gel process under variation of the mesopore size. Organic moieties in the pore walls are incorporated by substituting up to 10% of the silicon precursor tetramethylorthosilicate with bisilylated benzene molecules. After functionalization with sulfonic acid groups, the resulting sulfonated hybrid monoliths featuring a bimodal pore structure are investigated regarding proton conduction depending on temperature and relative humidity. The hierarchical pore system and controlled mesopore design turn out to be crucial for sulfonation and proton conduction. These sulfonated hybrid hierarchical monoliths containing only 10% organic precursor exhibit higher proton conduction at different relative humidities than sulfonated periodic mesoporous organosilica made of 100% bisilylated precursors exhibiting solely mesopores, even with a lower concentration of sulfonic acid groups.

  12. Calibrated and Interactive Modelling of Form-Active Hybrid Structures

    DEFF Research Database (Denmark)

    Quinn, Gregory; Holden Deleuran, Anders; Piker, Daniel

    2016-01-01

    at a fraction of the weight of traditional building elements and do so with a clear aesthetic expression of force flow and equilibrium. The design of FAHS is limited by one significant restriction: the geometry definition, form-finding and structural analysis are typically performed in separate and bespoke...... software packages which introduce interruptions and data exchange issues in the modelling pipeline. The mechanical precision, stability and open software architecture of Kangaroo has facilitated the development of proof-of-concept modelling pipelines which tackle this challenge and enable powerful...... materially-informed sketching. Making use of a projection-based dynamic relaxation solver for structural analysis, explorative design has proven to be highly effective....

  13. Multiresponsive hybrid microgels and hollow capsules with a layered structure.

    Science.gov (United States)

    Lapeyre, Véronique; Renaudie, Natacha; Dechezelles, Jean-François; Saadaoui, Hassan; Ravaine, Serge; Ravaine, Valérie

    2009-04-21

    Various stimuli-responsive composite particles with a high control of their internal structure and their corresponding hollow capsules are synthesized and characterized by photon correlation spectroscopy, TEM, and AFM. Core-shell particles with a silica core and a thermoresponsive shell are obtained by polymerization of N-isopropylacrylamide (NIPAM) in the presence of silica seeds grafted with a high density of gamma-methacryloxypropyltrimethoxysilane (MPS). The influence of the synthesis conditions is studied. The shell thickness increases when the monomer concentration increases in a limited range where uniform composite particles with a single core are obtained. At constant monomer concentration, the shell thickness does not depend on the size of the silica seeds, but the presence of free unbound microgels is observed when the silica surface area decreases. A range of particle diameters and shell thicknesses is thus obtained, which can lead to the corresponding hollow capsules by exposure to hydrofluoric acid solution. The volume phase transition temperature of these materials can be easily tuned by replacing the NIPAM monomer by another N-alkylacrylamide derivative. However, the incorporation of comonomers such as acrylic acid (AA) and a phenylboronic acid (PBA) derivative inhibits the formation of core-shell structures. In order to get pH or glucose responsiveness, these functional groups can be incorporated in the outer shell of a core-double shell structure, with pNIPAM as intermediate shell. pH-responsive and glucose-responsive composite particles are obtained by this method with a high control of their internal structure.

  14. Progressive Design of Plasmonic Metal-Semiconductor Ensemble toward Regulated Charge Flow and Improved Vis-NIR-Driven Solar-to-Chemical Conversion.

    Science.gov (United States)

    Han, Chuang; Quan, Quan; Chen, Hao Ming; Sun, Yugang; Xu, Yi-Jun

    2017-04-01

    Surface plasmon resonance (SPR)-mediated photocatalysis without the bandgap limitations of traditional semiconductor has aroused significant attention in solar-to-chemical energy conversion. However, the photocatalytic efficiency barely initiated by the SPR effects is still challenged by the low concentration and ineffective extraction of energetic hot electrons, slow charge migration rates, random charge diffusion directions, and the lack of highly active sites for redox reactions. Here, the tunable, progressive harvesting of visible-to-near infrared light (vis-NIR, λ > 570 nm) by designing plasmonic Au nanorods and metal (Au, Ag, or Pt) nanoparticle codecorated 1D CdS nanowire (1D CdS NW) ensemble is reported. The intimate integration of these metal nanostructures with 1D CdS NWs promotes the extraction and manipulated directional separation and migration of hot charge carriers in a more effective manner. Such cooperative synergy with tunable control of interfacial interaction, morphology optimization, and cocatalyst strategy results in the distinctly boosted performance for vis-NIR-driven plasmonic photocatalysis. This work highlights the significance of rationally progressive design of plasmonic metal-semiconductor-based composite system for boosting the regulated directional flow of hot charge carrier and thus the more efficient use of broad-spectrum solar energy conversion. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Cupric and cuprous oxide by reactive ion beam sputter deposition and the photosensing properties of cupric oxide metal-semiconductor-metal Schottky photodiodes

    Science.gov (United States)

    Hong, Min-Jyun; Lin, Yong-Chen; Chao, Liang-Chiun; Lin, Pao-Hung; Huang, Bohr-Ran

    2015-08-01

    Cupric (CuO) and cuprous (Cu2O) oxide thin films have been deposited by reactive ion beam sputter deposition at 400 °C with an Ar:O2 ratio from 2:1 to 12:1. With an Ar:O2 ratio of 2:1, single phase polycrystalline CuO thin films were obtained. Decreasing oxygen flow rate results in CuO + Cu2O and Cu2O + Cu mixed thin films. As Ar:O2 ratio reaches 12:1, Cu2O nanorods with diameter of 250 nm and length longer than 1 μm were found across the sample. Single phase CuO thin film exhibits an indirect band gap of 1.3 eV with a smooth surface morphology. CuO metal-semiconductor-metal (MSM) Schottky photodiodes (PD) were fabricated by depositing Cu interdigitated electrodes on CuO thin films. Photosensing properties of the CuO PD were characterized from 350 to 1300 nm and a maximum responsivity of 43 mA/W was found at λ = 700 nm. The MSM PD is RC limited with a decay time constant less than 1 μs.

  16. Measurement and simulation of top- and bottom-illuminated solar-blind AlGaN metal-semiconductor-metal photodetectors with high external quantum efficiencies

    Energy Technology Data Exchange (ETDEWEB)

    Brendel, Moritz, E-mail: moritz.brendel@fbh-berlin.de; Helbling, Markus; Knigge, Andrea; Brunner, Frank; Weyers, Markus [Ferdinand-Braun-Institut, Leibniz-Institut für Höchstfrequenztechnik (FBH), Gustav-Kirchhoff-Str. 4, 12489 Berlin (Germany)

    2015-12-28

    A comprehensive study on top- and bottom-illuminated Al{sub 0.5}Ga{sub 0.5}N/AlN metal-semiconductor-metal (MSM) photodetectors having different AlGaN absorber layer thickness is presented. The measured external quantum efficiency (EQE) shows pronounced threshold and saturation behavior as a function of applied bias voltage up to 50 V reaching about 50% for 0.1 μm and 67% for 0.5 μm thick absorber layers under bottom illumination. All experimental findings are in very good accordance with two-dimensional drift-diffusion modeling results. By taking into account macroscopic polarization effects in the hexagonal metal-polar +c-plane AlGaN/AlN heterostructures, new insights into the general device functionality of AlGaN-based MSM photodetectors are obtained. The observed threshold/saturation behavior is caused by a bias-dependent extraction of photoexcited holes from the Al{sub 0.5}Ga{sub 0.5}N/AlN interface. While present under bottom illumination for any AlGaN layer thickness, under top illumination this mechanism influences the EQE-bias characteristics only for thin layers.

  17. Quasi-Static Single-Component Hybrid Simulation of a Composite Structure with Multi-Axis Control

    DEFF Research Database (Denmark)

    Høgh, J.; Waldbjørn, J.; Wittrup-Schmidt, J.

    2015-01-01

    This paper presents a quasi-static hybrid simulation performed on a single component structure. Hybrid simulation is a substructural technique, where a structure is divided into two sections: a numerical section of the main structure and a physical experiment of the remainder. In previous cases...... to evaluate the validity of the method, the results are compared to a test of the emulated structure – referred to here as the reference test. It was found that the error introduced by compliance in the load train was significant. Digital image correlation was for this reason implemented in the hybrid...

  18. Ag-CuO-ZnO metal-semiconductor multiconcentric nanotubes for achieving superior and perdurable photodegradation.

    Science.gov (United States)

    Xu, Kaichen; Wu, Jiagen; Tan, Chuan Fu; Ho, Ghim Wei; Wei, Ang; Hong, Minghui

    2017-08-17

    Solar energy represents a robust and natural form of resource for environment remediation via photocatalytic pollutant degradation with minimum associated costs. However, due to the complexity of the photodegradation process, it has been a long-standing challenge to develop reliable photocatalytic systems with low recombination rates, excellent recyclability, and high utilization rates of solar energy, especially in the visible light range. In this work, a ternary hetero-nanostructured Ag-CuO-ZnO nanotube (NT) composite is fabricated via facile and low-temperature chemical and photochemical deposition methods. Under visible light irradiation, the as-synthesized ZnO NT based ternary composite exhibits a greater enhancement (∼300%) of photocatalytic activity than its counterpart, Ag-CuO-ZnO nanorods (NRs), in pollutant degradation. The enhanced photocatalytic capability is primarily attributed to the intensified visible light harvesting, efficient charge carrier separation and much larger surface area. Furthermore, our as-synthesised hybrid ternary Ag-CuO-ZnO NT composite demonstrates much higher photostability and retains ∼98% of degradation efficiency even after 20 usage cycles, which can be mainly ascribed to the more stable polar planes of ZnO NTs than those of ZnO NRs. These results afford a new route to construct ternary heterostructured composites with perdurable performance in sewage treatment and photocorrosion suppression.

  19. Full-spectrum photon management of solar cell structures for photovoltaic–thermoelectric hybrid systems

    International Nuclear Information System (INIS)

    Xu, Yuanpei; Xuan, Yimin; Yang, Lili

    2015-01-01

    Highlights: • A novel photon management method is proposed for hybrid photovoltaic–thermoelectric systems. • Composite structured surfaces enable creditable ultra-broadband anti-reflection property. • Incorporation of anti-reflection and light-trapping brings spectral absorption and transmission. • The efficient photon management of the structured surface is also omnidirectional. - Abstract: In this paper, a novel ultra-broadband photon management structure is proposed for crystalline silicon thin-film solar cells used in the photovoltaic–thermoelectric hybrid system. Nanostructures are employed on both front and back side. Optical behavior of the structure in ultra-broadband (300–2500 nm) are investigated through the Finite Difference Time Domain method. By combing moth-eye and inverted-parabolic surface, a new composite surface structure is proposed for anti-reflection in the ultra-broadband wavelengths. Front metallic nanoparticles, plasmonic back reflector and metallic gratings are studied for light-trapping and the effect of plasmonic back reflector is validated by the experimental data of the external quantum efficiency. The effects of incident angle are discussed for metallic gratings. Numerical computation shows that the incorporation of anti-reflection and light-trapping can obtain high absorption in the solar cell and ensure the rest incident light transmits to the thermoelectric generator efficiently. This work shows potential full-spectrum utilization of solar energy for various photovoltaic devices related with hybrid photovoltaic–thermoelectric systems

  20. Magneto-transport phenomena in metal/SiO2/n(p)-Si hybrid structures

    Science.gov (United States)

    Volkov, N. V.; Tarasov, A. S.; Rautskii, M. V.; Lukyanenko, A. V.; Bondarev, I. A.; Varnakov, S. N.; Ovchinnikov, S. G.

    2018-04-01

    Present review touches upon a subject of magnetotransport phenomena in hybrid structures which consist of ferromagnetic or nonmagnetic metal layer, layer of silicon oxide and silicon substrate with n- or p-type conductivity. Main attention will be paid to a number gigantic magnetotransport effects discovered in the devices fabricated on the base of the M/SiO2/n(p)-Si (M is ferromagnetic or paramagnetic metal) hybrid structures. These effects include bias induced dc magnetoresistance, gigantic magnetoimpedance, dc magnetoresistance induced by an optical irradiation and lateral magneto-photo-voltaic effect. The magnetoresistance ratio in ac and dc modes for some of our devices can exceed 106% in a magnetic field below 1 T. For lateral magneto-photo-voltaic effect, the relative change of photo-voltage in magnetic field can reach 103% at low temperature. Two types of mechanisms are responsible for sensitivity of the transport properties of the silicon based hybrid structures to magnetic field. One is related to transformation of the energy structure of the (donor) acceptor states including states near SiO2/n(p)-Si interface in magnetic field. Other mechanism is caused by the Lorentz force action. The features in behaviour of magnetotransport effects in concrete device depend on composition of the used structure, device topology and experimental conditions (bias voltage, optical radiation and others). Obtained results can be base for design of some electronic devices driven by a magnetic field. They can also provide an enhancement of the functionality for existing sensors.

  1. Dynamic Behavior of Hybrid APM (Advanced Pore Morphology Foam and Aluminum Foam Filled Structures

    Directory of Open Access Journals (Sweden)

    Joerg Weise

    2012-06-01

    Full Text Available The aim of this work is to evaluate the effect of different densities of hybrid aluminum polymer foam on the frequency behavior of a foam filled steel structure with different ratios between steel and foam masses. The foam filled structure is composed of three steel tubes with a welded flange at both ends bolted together to form a portal grounded by its free ends. Structure, internal and ground constraints have been designed and manufactured in order to minimize nonlinear effects and to guarantee optimal constraint conditions. Mode shapes and frequencies were verified with finite elements models (FEM to be in the range of experimental modal analysis, considering the frequency measurement range limits for instrumented hammer and accelerometer. Selected modes have been identified with suitable modal parameters extraction techniques. Each structure has been tested before and after filling, in order to compute the percentage variation of modal parameters. Two different densities of hybrid aluminum polymer foam have been tested and compared with structures filled with aluminum foams produced using the powder compact melting technique. All the foam fillings were able to suppress high frequency membrane modes which results in a reduction of environmental noise and an increase in performance of the components. Low frequency modes show an increase in damping ratio only when small thickness steel frames are filled with either Hybrid APM or Alulight foam.

  2. Highly Elastic and Ultratough Hybrid Ionic-Covalent Hydrogels with Tunable Structures and Mechanics.

    Science.gov (United States)

    Yang, Yanyu; Wang, Xing; Yang, Fei; Wang, Luning; Wu, Decheng

    2018-03-25

    Hybrid ionically-covalently crosslinked double-network (DN) hydrogels are attracting increasing attention on account of their self-recovery ability and fatigue resistance, but their relative low mechanical strength and tedious performance adjustment severely limit their applications. Herein, a new strategy to concurrently fabricate hybrid ionic-covalent DN hydrogels and modulate their structures and mechanics is reported, in which an in situ formed chitosan ionic network is incorporated by post-crosslinking the chitosan-based composite hydrogel using multivalent anions solutions. The obtained hybrid DN hydrogels exhibit predominant mechanical properties including superior elastic modulus, high tensile strength, and ultrahigh fracture energy because of the more efficient energy dissipation of rigid short-chain chitosan network. Notably, the swollen hydrogels still remain mechanically strong and tough even after immersion in water for 24 h. More significantly, simply changing the post-crosslinking time can vary the compactness and rigidity of the chitosan network in situ, achieving flexible and efficient modulation of the structures and mechanics of the hybrid DN hydrogels. This study opens up a new horizon in the preparation and regulation of DN hydrogels for promising applications in tissue scaffolds, actuators, and wearable devices. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Qualitative Fault Isolation of Hybrid Systems: A Structural Model Decomposition-Based Approach

    Science.gov (United States)

    Bregon, Anibal; Daigle, Matthew; Roychoudhury, Indranil

    2016-01-01

    Quick and robust fault diagnosis is critical to ensuring safe operation of complex engineering systems. A large number of techniques are available to provide fault diagnosis in systems with continuous dynamics. However, many systems in aerospace and industrial environments are best represented as hybrid systems that consist of discrete behavioral modes, each with its own continuous dynamics. These hybrid dynamics make the on-line fault diagnosis task computationally more complex due to the large number of possible system modes and the existence of autonomous mode transitions. This paper presents a qualitative fault isolation framework for hybrid systems based on structural model decomposition. The fault isolation is performed by analyzing the qualitative information of the residual deviations. However, in hybrid systems this process becomes complex due to possible existence of observation delays, which can cause observed deviations to be inconsistent with the expected deviations for the current mode in the system. The great advantage of structural model decomposition is that (i) it allows to design residuals that respond to only a subset of the faults, and (ii) every time a mode change occurs, only a subset of the residuals will need to be reconfigured, thus reducing the complexity of the reasoning process for isolation purposes. To demonstrate and test the validity of our approach, we use an electric circuit simulation as the case study.

  4. Glassy Carbon Coating Deposited on Hybrid Structure of Composite Materials

    Directory of Open Access Journals (Sweden)

    Posmyk A.

    2016-06-01

    Full Text Available This paper presents a method of production metal matrix composites with aluminum oxide foam covered by glassy carbon layer used as reinforcement. The glassy carbon coating was formed for decreasing of friction coefficient and reducing the wear. In first step of technology liquid glassy carbon precursor is on ceramic foam deposited, subsequently cured and carbonated at elevated temperature. In this way ceramic foam is covered with glassy carbon coating with thickness of 2-8 μm. It provides desirable amount of glassy carbon in the structure of the material. In the next step, porous spheres with carbon coating are infiltrated by liquid matrix of Al-Cu-Mg alloy. Thereby, equable distribution of glassy carbon in composite volume is achieved. Moreover, typical problems for composites reinforced by particles like sedimentation, agglomeration and clustering of particles are avoided. Tribological characteristics during friction in air versus cast iron as a counterpart were made. Produced composites with glassy carbon layer are characterised by friction coefficient between 0.08-0.20, thus meeting the typical conditions for solid lubricants.

  5. Development of Control Structure for Hybrid Wind Generators with Active Power Capability

    Directory of Open Access Journals (Sweden)

    Mehdi Niroomand

    2014-01-01

    Full Text Available A hierarchical control structure is proposed for hybrid energy systems (HES which consist of wind energy system (WES and energy storage system (ESS. The proposed multilevel control structure consists of four blocks: reference generation and mode select, power balancing, control algorithms, and switching control blocks. A high performance power management strategy is used for the system. Also, the proposed system is analyzed as an active power filter (APF with ability to control the voltage, to compensate the harmonics, and to deliver active power. The HES is designed with parallel DC coupled structure. Simulation results are shown for verification of the theoretical analysis.

  6. Research Update: The electronic structure of hybrid perovskite layers and their energetic alignment in devices

    Directory of Open Access Journals (Sweden)

    Selina Olthof

    2016-09-01

    Full Text Available In recent years, the interest in hybrid organic–inorganic perovskites has increased at a rapid pace due to their tremendous success in the field of thin film solar cells. This area closely ties together fundamental solid state research and device application, as it is necessary to understand the basic material properties to optimize the performances and open up new areas of application. In this regard, the energy levels and their respective alignment with adjacent charge transport layers play a crucial role. Currently, we are lacking a detailed understanding about the electronic structure and are struggling to understand what influences the alignment, how it varies, or how it can be intentionally modified. This research update aims at giving an overview over recent results regarding measurements of the electronic structure of hybrid perovskites using photoelectron spectroscopy to summarize the present status.

  7. Manipulating hybrid structures of polymer/a-Si for thin film solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Peng, Ying; He, Zhiqun, E-mail: zhqhe@bjtu.edu.cn, E-mail: J.I.B.Wilson@hw.ac.uk; Zhang, Zhi; Liang, Chunjun [Key Laboratory of Luminescence and Optical Information, Ministry of Education, Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China); Diyaf, Adel; Ivaturi, Aruna; Wilson, John I. B., E-mail: zhqhe@bjtu.edu.cn, E-mail: J.I.B.Wilson@hw.ac.uk [SUPA, School of Engineering and Physical Sciences, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom)

    2014-03-10

    A series of uniform polymer/amorphous silicon hybrid structures have been fabricated by means of solution-casting for polymer and radio frequency excited plasma enhanced chemical vapour deposition for amorphous silicon (a-Si:H). Poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) functioned as a photoactive donor, while the silicon layer acted as an acceptor. It is found that matching the hole mobility of the polymer to the electron mobility of amorphous silicon is critical to improve the photovoltaic performance from hybrid cells. A three-layer p-i-n structure of ITO/PEDOT:PSS(200 nm)/i-Si(450 nm)/n-Si(200 nm)/Al with a power conversion efficiency of 4.78% under a standard test condition was achieved.

  8. Multi-locus estimates of population structure and migration in a fence lizard hybrid zone.

    Directory of Open Access Journals (Sweden)

    Adam D Leaché

    Full Text Available A hybrid zone between two species of lizards in the genus Sceloporus (S. cowlesi and S. tristichus on the Mogollon Rim in Arizona provides a unique opportunity to study the processes of lineage divergence and merging. This hybrid zone involves complex interactions between 2 morphologically and ecologically divergent subspecies, 3 chromosomal groups, and 4 mitochondrial DNA (mtDNA clades. The spatial patterns of divergence between morphology, chromosomes and mtDNA are discordant, and determining which of these character types (if any reflects the underlying population-level lineages that are of interest has remained impeded by character conflict. The focus of this study is to estimate the number of populations interacting in the hybrid zone using multi-locus nuclear data, and to then estimate the migration rates and divergence time between the inferred populations. Multi-locus estimates of population structure and gene flow were obtained from 12 anonymous nuclear loci sequenced for 93 specimens of Sceloporus. Population structure estimates support two populations, and this result is robust to changes to the prior probability distribution used in the Bayesian analysis and the use of spatially-explicit or non-spatial models. A coalescent analysis of population divergence suggests that gene flow is high between the two populations, and that the timing of divergence is restricted to the Pleistocene. The hybrid zone is more accurately described as involving two populations belonging to S. tristichus, and the presence of S. cowlesi mtDNA haplotypes in the hybrid zone is an anomaly resulting from mitochondrial introgression.

  9. Interplay of Phonon and Exciton-Mediated Superconductivity in Hybrid Semiconductor-Superconductor Structures.

    Science.gov (United States)

    Skopelitis, Petros; Cherotchenko, Evgenia D; Kavokin, Alexey V; Posazhennikova, Anna

    2018-03-09

    We predict a strong enhancement of the critical temperature in a conventional Bardeen-Cooper-Schrieffer (BCS) superconductor in the presence of a bosonic condensate of exciton polaritons. The effect depends strongly on the ratio of the cutoff frequencies for phonon and exciton-polariton mediated BCS superconductivity, respectively. We also discuss a possible design of hybrid semiconductor-superconductor structures suitable for the experimental observation of such an effect.

  10. Tuning Structure and Properties of Graded Triblock Terpolymer-Based Mesoporous and Hybrid Films

    KAUST Repository

    Phillip, William A.

    2011-07-13

    Despite considerable efforts toward fabricating ordered, water-permeable, mesoporous films from block copolymers, fine control over pore dimensions, structural characteristics, and mechanical behavior of graded structures remains a major challenge. To this end, we describe the fabrication and performance characteristics of graded mesoporous and hybrid films derived from the newly synthesized triblock terpolymer, poly(isoprene-b-styrene-b-4-vinylpyridine). A unique morphology, unachievable in diblock copolymer systems, with enhanced mechanical integrity is evidenced. The film structure comprises a thin selective layer containing vertically aligned and nearly monodisperse mesopores at a density of more than 1014 per m2 above a graded macroporous layer. Hybridization via homopolymer blending enables tuning of pore size within the range of 16 to 30 nm. Solvent flow and solute separation experiments demonstrate that the terpolymer films have permeabilities comparable to commercial membranes, are stimuli-responsive, and contain pores with a nearly monodisperse diameter. These results suggest that moving to multiblock polymers and their hybrids may open new paths to produce high-performance graded membranes for filtration, separations, nanofluidics, catalysis, and drug delivery. © 2011 American Chemical Society.

  11. Broadband and wide-angle hybrid antireflection coatings prepared by combining interference multilayers with subwavelength structures

    Science.gov (United States)

    Bruynooghe, Stéphane; Schulze, Marcel; Helgert, Michael; Challier, Michel; Tonova, Diana; Sundermann, Michael; Koch, Thomas; Gatto, Alexandre; Kley, Ernst-Bernhard

    2016-07-01

    To reduce the intensity of the Fresnel reflections of optical components, subwavelength structures prepared by reactive ion etching of SiO2 thin films were combined as the outermost layer with a multilayer system made of conventional thin-film materials. A hybrid coating was thus realized, with the nanoscaled structured outermost layer expected to further improve the antireflection properties of common interference stacks. The microscopic and optical spectroscopic analysis of the subwavelength structures revealed that pillar-shaped nanostructures formed during etching exhibit low-refractive-index properties and have a depth-dependent refractive index. To take into account the refractive-index gradient in the coating design, the optical properties of the nanostructures were modeled using the effective-medium approximation. The calculated average effective refractive index turned out to be 1.11 at 500-nm wavelength. A hybrid coating was designed to minimize the residual reflectance in the 400-nm to 900-nm spectral range for BK7 glass substrate. Experimental results demonstrated that the hybrid-coating approach yields a low residual reflectance with very good omnidirectional properties, owing to the properties of the nanostructured surface.

  12. CPU-GPU hybrid accelerating the Zuker algorithm for RNA secondary structure prediction applications.

    Science.gov (United States)

    Lei, Guoqing; Dou, Yong; Wan, Wen; Xia, Fei; Li, Rongchun; Ma, Meng; Zou, Dan

    2012-01-01

    Prediction of ribonucleic acid (RNA) secondary structure remains one of the most important research areas in bioinformatics. The Zuker algorithm is one of the most popular methods of free energy minimization for RNA secondary structure prediction. Thus far, few studies have been reported on the acceleration of the Zuker algorithm on general-purpose processors or on extra accelerators such as Field Programmable Gate-Array (FPGA) and Graphics Processing Units (GPU). To the best of our knowledge, no implementation combines both CPU and extra accelerators, such as GPUs, to accelerate the Zuker algorithm applications. In this paper, a CPU-GPU hybrid computing system that accelerates Zuker algorithm applications for RNA secondary structure prediction is proposed. The computing tasks are allocated between CPU and GPU for parallel cooperate execution. Performance differences between the CPU and the GPU in the task-allocation scheme are considered to obtain workload balance. To improve the hybrid system performance, the Zuker algorithm is optimally implemented with special methods for CPU and GPU architecture. Speedup of 15.93× over optimized multi-core SIMD CPU implementation and performance advantage of 16% over optimized GPU implementation are shown in the experimental results. More than 14% of the sequences are executed on CPU in the hybrid system. The system combining CPU and GPU to accelerate the Zuker algorithm is proven to be promising and can be applied to other bioinformatics applications.

  13. CPU-GPU hybrid accelerating the Zuker algorithm for RNA secondary structure prediction applications

    Science.gov (United States)

    2012-01-01

    Background Prediction of ribonucleic acid (RNA) secondary structure remains one of the most important research areas in bioinformatics. The Zuker algorithm is one of the most popular methods of free energy minimization for RNA secondary structure prediction. Thus far, few studies have been reported on the acceleration of the Zuker algorithm on general-purpose processors or on extra accelerators such as Field Programmable Gate-Array (FPGA) and Graphics Processing Units (GPU). To the best of our knowledge, no implementation combines both CPU and extra accelerators, such as GPUs, to accelerate the Zuker algorithm applications. Results In this paper, a CPU-GPU hybrid computing system that accelerates Zuker algorithm applications for RNA secondary structure prediction is proposed. The computing tasks are allocated between CPU and GPU for parallel cooperate execution. Performance differences between the CPU and the GPU in the task-allocation scheme are considered to obtain workload balance. To improve the hybrid system performance, the Zuker algorithm is optimally implemented with special methods for CPU and GPU architecture. Conclusions Speedup of 15.93× over optimized multi-core SIMD CPU implementation and performance advantage of 16% over optimized GPU implementation are shown in the experimental results. More than 14% of the sequences are executed on CPU in the hybrid system. The system combining CPU and GPU to accelerate the Zuker algorithm is proven to be promising and can be applied to other bioinformatics applications. PMID:22369626

  14. New hybrid films based on cellulose and hydroxygallium phthalocyanine. Synergetic effects in the structure and properties.

    Science.gov (United States)

    Parra, Vicente; Vilar, Manuel Rei; Battaglini, Nicolas; Ferraria, Ana M; Rego, Ana M Botelho do; Boufi, Sami; Rodríguez-Méndez, María L; Fonavs, Egils; Muzikante, Inta; Bouvet, Marcel

    2007-03-27

    Hydroxygallium phthalocyanine (HOGaPc) and cellulose (from a trimethylsilyl derivative) have been used as native elements for the preparation of a novel family of hybrid films. By spin-coating, both components allow the building of films with different configurations on various substrates in a controlled way. The particularities of these hybrid films have been characterized by a range of techniques such as Fourier transform infrared spectroscopy (FTIRS) in attenuated total reflection using multiple internal reflections (ATR/MIR), absorption ultraviolet and visible spectroscopy (UV-vis), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and surface potential measurements using the Kelvin-Zisman vibrating capacitor probe (KP). This enabled determination of the influence of cellulose on the arrangement of HOGaPc and, consequently, control of the relation between the structure and the properties of the films. Finally, gas sensor tests were performed to check the potentialities of these hybrid films. In particular, the synergetic behavior between the film-forming materials allows a fast and sensible change in surface potential after cyclic exposures to ozone (O3, 100 ppb) and nitrogen. Overall, we present the advantages of combining phthalocyanine with cellulose in enhancing the properties of the final product. Introduction of cellulose as a host material opens up a new area of hybrid films.

  15. Nacre-like hybrid films: Structure, properties, and the effect of relative humidity.

    Science.gov (United States)

    Abba, Mohammed T; Hunger, Philipp M; Kalidindi, Surya R; Wegst, Ulrike G K

    2015-03-01

    Functional materials often are hybrids composed of biopolymers and mineral constituents. The arrangement and interactions of the constituents frequently lead to hierarchical structures with exceptional mechanical properties and multifunctionality. In this study, hybrid thin films with a nacre-like brick-and-mortar microstructure were fabricated in a straightforward and reproducible manner through manual shear casting using the biopolymer chitosan as the matrix material (mortar) and alumina platelets as the reinforcing particles (bricks). The ratio of inorganic to organic content was varied from 0% to 15% and the relative humidities from 36% to 75% to determine their effects on the mechanical properties. It was found that increasing the volume fraction of alumina from 0% to 15% results in a twofold increase in the modulus of the film, but decreases the tensile strength by up to 30%, when the volume fraction of alumina is higher than 5%. Additionally, this study quantifies and illustrates the critical role of the relative humidity on the mechanical properties of the hybrid film. Increasing the relative humidity from 36% to 75% decreases the modulus and strength by about 45% and triples the strain at failure. These results suggest that complex hybrid materials can be manufactured and tailor made for specific applications or environmental conditions. Copyright © 2015. Published by Elsevier Ltd.

  16. An Ag-grid/graphene hybrid structure for large-scale, transparent, flexible heaters.

    Science.gov (United States)

    Kang, Junmo; Jang, Yonghee; Kim, Youngsoo; Cho, Seung-Hyun; Suhr, Jonghwan; Hong, Byung Hee; Choi, Jae-Boong; Byun, Doyoung

    2015-04-21

    Recently, carbon materials such as carbon nanotubes and graphene have been proposed as alternatives to indium tin oxide (ITO) for fabricating transparent conducting materials. However, obtaining low sheet resistance and high transmittance of these carbon materials has been challenging due to the intrinsic properties of the materials. In this paper, we introduce highly transparent and flexible conductive films based on a hybrid structure of graphene and an Ag-grid. Electrohydrodynamic (EHD) jet printing was used to produce a micro-scale grid consisting of Ag lines less than 10 μm wide. We were able to directly write the Ag-grid on a large-area graphene/flexible substrate due to the high conductivity of graphene. The hybrid electrode could be fabricated using hot pressing transfer and EHD jet printing in a non-vacuum, maskless, and low-temperature environment. The hybrid electrode offers an effective and simple route for achieving a sheet resistance as low as ∼4 Ω per square with ∼78% optical transmittance. Finally, we demonstrate that transparent flexible heaters based on the hybrid conductive films could be used in a vehicle or a smart window system.

  17. Optoelectronic Properties of Van Der Waals Hybrid Structures: Fullerenes on Graphene Nanoribbons

    Science.gov (United States)

    Correa, Julián David; Orellana, Pedro Alejandro; Pacheco, Mónica

    2017-01-01

    The search for new optical materials capable of absorbing light in the frequency range from visible to near infrared is of great importance for applications in optoelectronic devices. In this paper, we report a theoretical study of the electronic and optical properties of hybrid structures composed of fullerenes adsorbed on graphene and on graphene nanoribbons. The calculations are performed in the framework of the density functional theory including the van der Waals dispersive interactions. We found that the adsorption of the C60 fullerenes on a graphene layer does not modify its low energy states, but it has strong consequences for its optical spectrum, introducing new absorption peaks in the visible energy region. The optical absorption of fullerenes and graphene nanoribbon composites shows a strong dependence on photon polarization and geometrical characteristics of the hybrid systems, covering a broad range of energies. We show that an external electric field across the nanoribbon edges can be used to tune different optical transitions coming from nanoribbon–fullerene hybridized states, which yields a very rich electro-absorption spectrum for longitudinally polarized photons. We have carried out a qualitative analysis on the potential of these hybrids as possible donor-acceptor systems in photovoltaic cells. PMID:28336904

  18. Insect damages on structural, morphologic and composition of Bt maize hybrids to silage

    Directory of Open Access Journals (Sweden)

    Geraldo Balieiro Neto

    2013-03-01

    Full Text Available It was aimed to evaluate the effect of insect damage on the morphologic and structural characteristics and chemical composition from maize hybrids DKB 390 and AG 8088 with the Cry1Ab trait versus its nonbiotech counterpart. The GMO did not receive insecticide application and the conventional hybrids received one deltametrina (2.8% application at 42 days. The damages caused bySpodoptera frugiperda and Helicoverpa zea in hybrids with Cry1Ab were smaller than its nonbiotech counterpart. After harvest, 95 days after seedling plants were separated in stalks, ears, leafs, dead leafs and floral pennant. The experimental design was randomized block in factorial arrangement 2 x 2. The height of plant and height of ear, percentage and amount of dead leafs from hybrids with the Cry1Ab were higher than its nonbiotech counterpart. There was higher nutrients transfer from stalks to grain filling and smaller rate stalks:ear on transgenic plant. The quality of the transgenic plants can be better when harvest earlier, by increasing no fiber carbohydrates, but when harvest latter, by increasing stalk percentage and stalk lignin content.

  19. Optoelectronic Properties of Van Der Waals Hybrid Structures: Fullerenes on Graphene Nanoribbons.

    Science.gov (United States)

    Correa, Julián David; Orellana, Pedro Alejandro; Pacheco, Mónica

    2017-03-20

    The search for new optical materials capable of absorbing light in the frequency range from visible to near infrared is of great importance for applications in optoelectronic devices. In this paper, we report a theoretical study of the electronic and optical properties of hybrid structures composed of fullerenes adsorbed on graphene and on graphene nanoribbons. The calculations are performed in the framework of the density functional theory including the van der Waals dispersive interactions. We found that the adsorption of the C 60 fullerenes on a graphene layer does not modify its low energy states, but it has strong consequences for its optical spectrum, introducing new absorption peaks in the visible energy region. The optical absorption of fullerenes and graphene nanoribbon composites shows a strong dependence on photon polarization and geometrical characteristics of the hybrid systems, covering a broad range of energies. We show that an external electric field across the nanoribbon edges can be used to tune different optical transitions coming from nanoribbon-fullerene hybridized states, which yields a very rich electro-absorption spectrum for longitudinally polarized photons. We have carried out a qualitative analysis on the potential of these hybrids as possible donor-acceptor systems in photovoltaic cells.

  20. Optoelectronic Properties of Van Der Waals Hybrid Structures: Fullerenes on Graphene Nanoribbons

    Directory of Open Access Journals (Sweden)

    Julián David Correa

    2017-03-01

    Full Text Available The search for new optical materials capable of absorbing light in the frequency range from visible to near infrared is of great importance for applications in optoelectronic devices. In this paper, we report a theoretical study of the electronic and optical properties of hybrid structures composed of fullerenes adsorbed on graphene and on graphene nanoribbons. The calculations are performed in the framework of the density functional theory including the van der Waals dispersive interactions. We found that the adsorption of the C 60 fullerenes on a graphene layer does not modify its low energy states, but it has strong consequences for its optical spectrum, introducing new absorption peaks in the visible energy region. The optical absorption of fullerenes and graphene nanoribbon composites shows a strong dependence on photon polarization and geometrical characteristics of the hybrid systems, covering a broad range of energies. We show that an external electric field across the nanoribbon edges can be used to tune different optical transitions coming from nanoribbon–fullerene hybridized states, which yields a very rich electro-absorption spectrum for longitudinally polarized photons. We have carried out a qualitative analysis on the potential of these hybrids as possible donor-acceptor systems in photovoltaic cells.

  1. High power experimental studies of hybrid photonic band gap accelerator structures

    Directory of Open Access Journals (Sweden)

    JieXi Zhang

    2016-08-01

    Full Text Available This paper reports the first high power tests of hybrid photonic band gap (PBG accelerator structures. Three hybrid PBG (HPBG structures were designed, built and tested at 17.14 GHz. Each structure had a triangular lattice array with 60 inner sapphire rods and 24 outer copper rods sandwiched between copper disks. The dielectric PBG band gap map allows the unique feature of overmoded operation in a TM_{02} mode, with suppression of both lower order modes, such as the TM_{11} mode, as well as higher order modes. The use of sapphire rods, which have negligible dielectric loss, required inclusion of the dielectric birefringence in the design. The three structures were designed to sequentially reduce the peak surface electric field. Simulations showed relatively high surface fields at the triple point as well as in any gaps between components in the clamped assembly. The third structure used sapphire rods with small pin extensions at each end and obtained the highest gradient of 19  MV/m, corresponding to a surface electric field of 78  MV/m, with a breakdown probability of 5×10^{-1} per pulse per meter for a 100-ns input power pulse. Operation at a gradient above 20  MV/m led to runaway breakdowns with extensive light emission and eventual damage. For all three structures, multipactor light emission was observed at gradients well below the breakdown threshold. This research indicated that multipactor triggered at the triple point limited the operational gradient of the hybrid structure.

  2. Layer-by-layer modification of thin-film metal-semiconductor multilayers with ultrashort laser pulses

    Science.gov (United States)

    Romashevskiy, S. A.; Tsygankov, P. A.; Ashitkov, S. I.; Agranat, M. B.

    2018-05-01

    The surface modifications in a multilayer thin-film structure (50-nm alternating layers of Si and Al) induced by a single Gaussian-shaped femtosecond laser pulse (350 fs, 1028 nm) in the air are investigated by means of atomic-force microscopy (AFM), scanning electron microscopy (SEM), and optical microscopy (OM). Depending on the laser fluence, various modifications of nanometer-scale metal and semiconductor layers, including localized formation of silicon/aluminum nanofoams and layer-by-layer removal, are found. While the nanofoams with cell sizes in the range of tens to hundreds of nanometers are produced only in the two top layers, layer-by-layer removal is observed for the four top layers under single pulse irradiation. The 50-nm films of the multilayer structure are found to be separated at their interfaces, resulting in a selective removal of several top layers (up to 4) in the form of step-like (concentric) craters. The observed phenomenon is associated with a thermo-mechanical ablation mechanism that results in splitting off at film-film interface, where the adhesion force is less than the bulk strength of the used materials, revealing linear dependence of threshold fluences on the film thickness.

  3. Studies on the S-band bunching system with the Hybrid Bunching-accelerating Structure

    Science.gov (United States)

    Pei, Shi-Lun; Gao, Bin

    2018-04-01

    Generally, a standard bunching system is composed of a standing-wave (SW) pre-buncher (PB), a traveling-wave (TW) buncher (B) and a standard accelerating structure. In the industrial area, the bunching system is usually simplified by eliminating the PB and integrating the B and the standard accelerating structure together to form a β-varied accelerating structure. The beam capturing efficiency for this kind of simplified system is often worse than that for the standard one. The hybrid buncher (HB) has been proved to be a successful attempt to reduce the cost but preserve the beam quality as much as possible. Here we propose to exclusively simplify the standard bunching system by integrating the PB, the B and the standard accelerating structure together to form a Hybrid Bunching-accelerating Structure (HBaS). Compared to the standard bunching system, the one based on the HBaS is more compact, and the cost is lowered to the largest extent. With almost the same beam transportation efficiency (∼70%) from the electron gun to the linac exit, the peak-to-peak (p-to-p) beam energy spread and the 1 σ emittance of the linac with the HBaS are ∼20% and ∼60% bigger than those of the linac based on the split PB/B/standard accelerating structure system. Nonetheless, the proposed HBaS can be widely applied in the industrial linacs to greatly increase the beam capturing efficiency without fairly increasing the construction cost.

  4. Design of hybrid electron linac with standing wave buncher and traveling wave structure

    International Nuclear Information System (INIS)

    Kutsaev, S.V.; Sobenin, N.P.; Smirnov, A.Yu.; Kamenschikov, D.S.; Gusarova, M.A.; Nikolskiy, K.I.; Zavadtsev, A.A.; Lalayan, M.V.

    2011-01-01

    A disk-loaded waveguide (DLW) is the most common structure for compact linear accelerators working in a traveling wave (TW) regime. Among its advantages are high shunt impedance and manufacturing simplicity. The other popular structure is an on-axis coupled bi-periodical accelerating structure (BAS) that works in standing wave (SW) regime. Both the standing and the traveling wave regimes have their own advantages and disadvantages. The design of the hybrid accelerator with SW buncher and TW accelerating section presented in this paper unites the advantages of both regimes. For example, the buncher in the hybrid accelerator is shorter than in a pure TW accelerator, and it requires no solenoid; this structure is more technologically convenient as it does not require a circulator. The other way to combine the advantages of DLW and BAS is to design a magnetic coupled disk-loaded waveguide (DLW-M). This paper also presents the results of a survey study that analyzed the electrodynamical parameters of such a structure and compared them with those of DLW. The experimental data is also presented. Higher order modes, multipacting discharge and thermal simulations show that DLW-M structure is more preferable to classical DLW.

  5. Design and Fabrication of a Novel Hybrid-Structure Heat Pipe for a Concentrator Photovoltaic

    Directory of Open Access Journals (Sweden)

    Heiu-Jou Shaw

    2012-10-01

    Full Text Available This study presents a design method to fabricate a novel hybrid-structure flat plate heat pipe (NHSP heat pipe for a concentrator photovoltaic. The NHSP heat pipe is composed of a flattened copper pipe and a sintered wick structure, and a coronary-stent-like rhombic copper mesh supports the structure. The coronary-stent-like supporting structure enhances the mechanical strength and shortens the reflux path of the working fluid. Experiments demonstrate that the sintered capillary heat pipe reduces the thermal resistance by approximately 72%, compared to a traditional copper mesh-screen heat pipe. Furthermore, it can reduce thermal resistance by 65% after a supporting structure is added to the heat pipe. The results show that the NHSP heat pipe provided the best performance for the concentrator photovoltaic, which can increase photoelectric conversion efficiency by approximately 3.1%, compared to an aluminum substrate.

  6. Metal-semiconductor transition materials. FeS and VO{sub 2} thin films by RF reactive sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Fu Ganhua

    2007-06-15

    In the present work, two MST systems, FeS and VO{sub 2} thin films were investigated. Iron sulfide thin films over a range of composition were prepared by reactive sputtering. The influence of the substrate, sputter power, substrate temperature and stoichiometry on the structure and MST of iron sulfide films was investigated. Iron sulfide films deposited at different temperatures show temperature dependent structure and MST. FeS films on float glass show (110) and (112) orientations when the substrate temperature is 200 and 500 C, respectively. The transition temperature and width of the hysteresis loop determined from the temperature dependent conductivity curves of iron sulfide films decrease with the substrate temperature. Fe and S excess in FeS films both result in the decrease of the transition temperature and width of the hysteresis loop. The vacuum-annealing affects the MST of FeS films significantly. When FeS films were annealed below the deposition temperature, the transition temperature decreases; otherwise increases. The residual stress plays an important role during the annealing process. The higher the residual stress inside the FeS films is, the higher the transition temperature of FeS films. With the increase of the annealing temperature, the residual stress in FeS films is first released and then enhances, which gives rise first to the decrease and then increase of the transition temperature of FeS films. At high substrate temperatures, the residual stress is higher. In addition, the MST of FeS films was influenced by the ambient aging. With the increase of the aging time, the transition temperature first increases and then decreases. FeS films with different thicknesses were prepared. The correlation between the film thickness (grain size) and the MST switching characteristics of FeS films was established. With the decrease of the grain size, the density of grain boundaries increases, causing the increase of the conductivity of the semiconducting

  7. Metal-semiconductor transition materials. FeS and VO2 thin films by RF reactive sputtering

    International Nuclear Information System (INIS)

    Fu, Ganhua

    2007-06-01

    In the present work, two MST systems, FeS and VO 2 thin films were investigated. Iron sulfide thin films over a range of composition were prepared by reactive sputtering. The influence of the substrate, sputter power, substrate temperature and stoichiometry on the structure and MST of iron sulfide films was investigated. Iron sulfide films deposited at different temperatures show temperature dependent structure and MST. FeS films on float glass show (110) and (112) orientations when the substrate temperature is 200 and 500 C, respectively. The transition temperature and width of the hysteresis loop determined from the temperature dependent conductivity curves of iron sulfide films decrease with the substrate temperature. Fe and S excess in FeS films both result in the decrease of the transition temperature and width of the hysteresis loop. The vacuum-annealing affects the MST of FeS films significantly. When FeS films were annealed below the deposition temperature, the transition temperature decreases; otherwise increases. The residual stress plays an important role during the annealing process. The higher the residual stress inside the FeS films is, the higher the transition temperature of FeS films. With the increase of the annealing temperature, the residual stress in FeS films is first released and then enhances, which gives rise first to the decrease and then increase of the transition temperature of FeS films. At high substrate temperatures, the residual stress is higher. In addition, the MST of FeS films was influenced by the ambient aging. With the increase of the aging time, the transition temperature first increases and then decreases. FeS films with different thicknesses were prepared. The correlation between the film thickness (grain size) and the MST switching characteristics of FeS films was established. With the decrease of the grain size, the density of grain boundaries increases, causing the increase of the conductivity of the semiconducting phase

  8. Substructure hybrid testing of reinforced concrete shear wall structure using a domain overlapping technique

    Science.gov (United States)

    Zhang, Yu; Pan, Peng; Gong, Runhua; Wang, Tao; Xue, Weichen

    2017-10-01

    An online hybrid test was carried out on a 40-story 120-m high concrete shear wall structure. The structure was divided into two substructures whereby a physical model of the bottom three stories was tested in the laboratory and the upper 37 stories were simulated numerically using ABAQUS. An overlapping domain method was employed for the bottom three stories to ensure the validity of the boundary conditions of the superstructure. Mixed control was adopted in the test. Displacement control was used to apply the horizontal displacement, while two controlled force actuators were applied to simulate the overturning moment, which is very large and cannot be ignored in the substructure hybrid test of high-rise buildings. A series of tests with earthquake sources of sequentially increasing intensities were carried out. The test results indicate that the proposed hybrid test method is a solution to reproduce the seismic response of high-rise concrete shear wall buildings. The seismic performance of the tested precast high-rise building satisfies the requirements of the Chinese seismic design code.

  9. Fabrication and characterization of magnetically tunable metal-semiconductor schottky diode using barium hexaferrite thin film on gold

    Directory of Open Access Journals (Sweden)

    Jotinder Kaur

    2016-05-01

    Full Text Available Barium Hexaferrite (BaM is an extensively studied magnetic material due to its potential device application. In this paper, we study Schottky junction diodes fabricated using gold and BaM and demonstrate the function of a spintronic device. Gold (50 nm/silicon substrate was used to grow the BaM thin films (100-150 nm using pulsed laser deposition. I-V characteristics were measured on the Au/BaM structure sweeping the voltage from ±5 volts. The forward and reverse bias current-voltage curves show diode like rectifying characteristics. The threshold voltage decreases while the output current increases with increase in the applied external magnetic field showing that the I-V characteristics of the BaM based Schottky junction diodes can be tuned by external magnetic field. It is also demonstrated that, the fabricated Schottky diode can be used as a half-wave rectifier, which could operate at high frequencies in the range of 1 MHz compared to the regular p-n junction diodes, which rectify below 10 kHz. In addition, it is found that above 1 MHz, Au/BaM diode can work as a rectifier as well as a capacitor filter, making the average (dc voltage much larger.

  10. Fabrication and characterization of magnetically tunable metal-semiconductor schottky diode using barium hexaferrite thin film on gold

    Science.gov (United States)

    Kaur, Jotinder; Sharma, Vinay; Sharma, Vipul; Veerakumar, V.; Kuanr, Bijoy K.

    2016-05-01

    Barium Hexaferrite (BaM) is an extensively studied magnetic material due to its potential device application. In this paper, we study Schottky junction diodes fabricated using gold and BaM and demonstrate the function of a spintronic device. Gold (50 nm)/silicon substrate was used to grow the BaM thin films (100-150 nm) using pulsed laser deposition. I-V characteristics were measured on the Au/BaM structure sweeping the voltage from ±5 volts. The forward and reverse bias current-voltage curves show diode like rectifying characteristics. The threshold voltage decreases while the output current increases with increase in the applied external magnetic field showing that the I-V characteristics of the BaM based Schottky junction diodes can be tuned by external magnetic field. It is also demonstrated that, the fabricated Schottky diode can be used as a half-wave rectifier, which could operate at high frequencies in the range of 1 MHz compared to the regular p-n junction diodes, which rectify below 10 kHz. In addition, it is found that above 1 MHz, Au/BaM diode can work as a rectifier as well as a capacitor filter, making the average (dc) voltage much larger.

  11. Theoretical investigation of the electronic structures and carrier transport of hybrid graphene and boron nitride nanostructure

    Directory of Open Access Journals (Sweden)

    Jia-Tao Sun

    2012-09-01

    graphene and hexagonal boron nitride (C-BN nanostructures receive much research interest due to the complementary electronic properties. Graphene is a zero-gap semiconductor, while hexagonal boron nitride (h-BN is a wide gap semiconductor. Here we studied the electronic structures and carrier transport of hybrid C-BN nanostructures by using first principles calculations and deformation potential theory. We have found that the physical quantities in these systems under study, band gap, effective mass, deformation potential, and carrier mobility, can be categorised into three different families depending on the width of graphene nanoribbon. This family behavior is similar to pristine armchair graphene nanoribbon, but with slight difference from the individual component. New opportunities of designing nanoelectric devices are discussed by utilizing the quantum confinement effect based on such kind of hybrid nanostructures.

  12. Joining of Metal-Plastics-Hybrid Structures Using Laser Radiation by Considering the Surface Structure of the Metal

    Directory of Open Access Journals (Sweden)

    Christian Hopmann

    2016-01-01

    Full Text Available Lightweight construction is a central technology in today’s industrial production. One way to achieve the climate goals is the production of hybrid compounds of metal and plastic. The manufacturing process for these hybrid parts can be divided into in-mold assembly and postmold assembly. The postmold assembly includes thermal joining by laser, which is applied in the context of this paper. For the investigations, four plastics (MABS, PA6.6-GF35, PP, and PC, which differ in their properties, and three metals (unalloyed steel, stainless steel, and aluminum are combined and analyzed. These materials have been used, since they have a huge significance in the automotive industry. Preliminary studies showed that an adhesive bond between the two materials is achieved using metal with a structured surface. According to these studies, three structuring processes for metals (selective laser melting (SLM, NRX, and a welded metallic tissue are tested. The quality of the material/structure combinations is tested in tensile-shear-tests, microscopy images, and alternating climate tests. Compounds with SLM-Structure achieve highest strength, while compounds with aluminum are much more complex to manufacture.

  13. New types of wheat chromosomal structural variations in derivatives of wheat-rye hybrids.

    Science.gov (United States)

    Tang, Zongxiang; Li, Meng; Chen, Lei; Wang, Yangyang; Ren, Zhenglong; Fu, Shulan

    2014-01-01

    Chromosomal rearrangements induced by wheat-rye hybridization is a very well investigated research topic. However, the structural alterations of wheat chromosomes in wheat-rye hybrids are seldom reported. Octoploid triticale lines were derived from common wheat Triticum. aestivum L. 'Mianyang11'×rye Secale cereale L. 'Kustro'. Some progeny were obtained by the controlled backcrossing of triticale with 'Mianyang11' and common wheat T. aestivum L. 'Chuannong27' followed by self-fertilization. Fluorescence in situ hybridization (FISH) and genomic in situ hybridization (GISH) using Oligo-pSc119.2-1, Oligo-pTa535-1 and rye genomic DNA as probes were used to analyze the mitotic chromosomes of these progeny. Alterations of wheat chromosomes including 5A, 6A, 1B, 2B, 6B, 7B, 1D, 3D and 7D were observed. 5AL arm carrying intercalary Oligo-pSc119.2-1, Oligo-pTa535-1 or both Oligo-pSc119.2-1 and Oligo-pTa535-1 signals, 6AS, 1BS and 1DL arms containing terminal Oligo-pSc119.2-1 signal, 6BS and 3DS arms without terminal Oligo-pSc119.2-1 signal, 7BS without subtelomeric Oligo-pSc119.2-1 signal and 7DL with intercalary Oligo-pSc119.2-1 signal have been observed. However, these changed wheat chromosomes have not been detected in 'Mianyang11' and Chuannong 27. The altered 5A, 6A, 7B and 7D chromosomes in this study have not been reported and represent several new karyotype structures of common wheat chromosomes. These rearranged wheat chromosomes in the present study afford some new genetic variations for wheat breeding program and are valuable materials for studying the biological function of tandem repetitive DNA sequences.

  14. Synthesis of palladium nanoparticle modified reduced graphene oxide and multi-walled carbon nanotube hybrid structures for electrochemical applications

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Jie, E-mail: hujie@tyut.edu.cn [Micro and Nano System Research Center, Key Lab of Advanced Transducers and Intelligent Control System (Ministry of Education) & College of Information Engineering, Taiyuan University of Technology, Taiyuan, 030024, Shanxi (China); Zhao, Zhenting; Zhang, Jun; Li, Gang; Li, Pengwei; Zhang, Wendong [Micro and Nano System Research Center, Key Lab of Advanced Transducers and Intelligent Control System (Ministry of Education) & College of Information Engineering, Taiyuan University of Technology, Taiyuan, 030024, Shanxi (China); Lian, Kun, E-mail: liankun@tyut.edu.cn [Micro and Nano System Research Center, Key Lab of Advanced Transducers and Intelligent Control System (Ministry of Education) & College of Information Engineering, Taiyuan University of Technology, Taiyuan, 030024, Shanxi (China); School of Nano-Science and Nano-Engineering, Suzhou & Collaborative Innovation Center of Suzhou Nano Science and Technology, Xi' an Jiaotong University, Xi' an, 710049 (China); Center for Advanced Microstructures and Devices, Louisiana State University, LA, 70806 (United States)

    2017-02-28

    Graphical abstract: A sensitive hydrazine electrochemical sensor was fabricated by using palladium (Pd) nanoparticle functionalized reduced graphene oxide (rGO) and multi-walled carbon nanotube (MWCNTs) hybrid structures (Pd/rGO-MWCNTs). - Highlights: • rGO-MWCNTs hybrid structures and Pd nanoparticles are prepared using electrochemical methods. • rGO-MWCNTs hybrid films are used as supports and co-catalysts for Pd nanoparticles. • The Pd/rGO-MWCNTs hybrid structure based sensor shows an ultra-high sensitivity of 7.09 μA μM{sup −1} cm{sup −2} and a low detection limit of 0.15 μM. • The proposed electrochemical sensor exhibits excellent selectivity. - Abstract: In this work, palladium (Pd) nanoparticles functionalized reduced graphene oxide (rGO) and multi-walled carbon nanotubes (MWCNTs) hybrid structures (Pd/rGO-MWCNTs) were successfully prepared by a combination of electrochemical reduction with electrodeposition method. The morphology, structure, and composition of the Pd/rGO-MWCNTs hybrid were characterized by scanning electron microscopy, transmission electron microscopy and energy dispersive spectroscopy. The as-synthesized hybrid structures were modified on the glassy carbon electrode (GCE) and further utilized for hydrazine sensing. Electrochemical impedance spectroscopic, cyclic voltammetry and single-potential amperometry experiments were carried out on Pd/rGO-MWCNTs hybrid structures to investigate the interface properties and sensing performance. The measured results demonstrate that the fabricated Pd/rGO-MWCNTs/GCE sensor show a high sensitivity of 7.09 μA μM{sup −1} cm{sup −2} in a large concentration range of 1.0 to 1100 μM and a low detection limit of 0.15 μM. Moreover, the as-prepared sensor exhibits good selectivity and stability for the determination of hydrazine under interference conditions.

  15. Electronic structure modeling of InAs/GaSb superlattices with hybrid density functional theory

    Energy Technology Data Exchange (ETDEWEB)

    Garwood, Tristan [Univ. of New Mexico, Albuquerque, NM (United States). Center for High Technology Materials; Modine, Normand A. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Krishna, S. [Univ. of New Mexico, Albuquerque, NM (United States). Center for High Technology Materials

    2016-12-18

    The application of first-principles calculations holds promise for greatly improving our understanding of semiconductor superlattices. By developing a procedure to accurately predict band gaps using hybrid density functional theory, it lays the groundwork for future studies investigating more nuanced properties of these structures. Our approach allows a priori prediction of the properties of SLS structures using only the band gaps of the constituent materials. Furthermore, it should enable direct investigation of the effects of interface structure, e.g., intermixing or ordering at the interface, on SLS properties. In this paper, we present band gap data for various InAs/GaSb type-II superlattice structures calculated using the generalized Kohn-Sham formulation of density functional theory. A PBE0-type hybrid functional was used, and the portion of the exact exchange was tuned to fit the band gaps of the binary compounds InAs and GaSb with the best agreement to bulk experimental values obtained with 18% of the exact exchange. The heterostructures considered in this study are 6 monolayer (ML) InAs/6 ML GaSb, 8 ML InAs/8 ML GaSb and 10 ML InAs/10 ML GaSb with deviations from the experimental band gaps ranging from 3% to 11%.

  16. On hydrophilicity improvement of the porous anodic alumina film by hybrid nano/micro structuring

    Science.gov (United States)

    Wang, Weichao; Zhao, Wei; Wang, Kaige; Wang, Lei; Wang, Xuewen; Wang, Shuang; Zhang, Chen; Bai, Jintao

    2017-09-01

    In both, laboratory and industry, tremendous attention is paid to discover an effective technique to produce uniform, controllable and (super) hydrophilic surfaces over large areas that are useful in a wide range of applications. In this investigation, by combing porous anodic alumina (PAA) film with nano-structures and microarray of aluminum, the hydrophilicity of hybrid nano-micro structure has been significantly improved. It is found some factors can affect the hydrophilicity of film, such as the size and aspect ratio of microarray, the thickness of nano-PAA film etc. Comparing with pure nano-PAA films and microarray, the hybrid nano-micro structure can provide uniform surface with significantly better hydrophilicity. The improvement can be up to 84%. Also, this technique exhibits good stability and repeatability for industrial production. By optimizing the thickness of nano-PAA film and aspect ratio of micro-structures, super-hydrophilicity can be reached. This study has obvious prospect in the fields of chemical industry, biomedical engineering and lab-on-a-chip applications.

  17. Self-diagnosis of structures strengthened with hybrid carbon-fiber-reinforced polymer sheets

    Science.gov (United States)

    Wu, Z. S.; Yang, C. Q.; Harada, T.; Ye, L. P.

    2005-06-01

    The correlation of mechanical and electrical properties of concrete beams strengthened with hybrid carbon-fiber-reinforced polymer (HCFRP) sheets is studied in this paper. Two types of concrete beams, with and without reinforcing bars, are strengthened with externally bonded HCFRP sheets, which have a self-structural health monitoring function due to the electrical conduction and piezoresistivity of carbon fibers. Parameters investigated include the volume fractions and types of carbon fibers. According to the investigation, it is found that the hybridization of uniaxial HCFRP sheets with several different types of carbon fibers is a viable method for enhancing the mechanical properties and obtaining a built-in damage detection function for concrete structures. The changes in electrical resistance during low strain ranges before the rupture of carbon fibers are generally smaller than 1%. Nevertheless, after the gradual ruptures of carbon fibers, the electrical resistance increases remarkably with the strain in a step-wise manner. For the specimens without reinforcing bars, the electrical behaviors are not stable, especially during the low strain ranges. However, the electrical behaviors of the specimens with reinforcing bars are relatively stable, and the whole range of self-sensing function of the HCFRP-strengthened RC structures has realized the conceptual design of the HCFRP sensing models and is confirmed by the experimental investigations. The relationships between the strain/load and the change in electrical resistance show the potential self-monitoring capacity of HCFRP reinforcements used for strengthening concrete structures.

  18. Fabrication of Nano-Micro Hybrid Structures by Replication and Surface Treatment of Nanowires

    Directory of Open Access Journals (Sweden)

    Yeonho Jeong

    2017-07-01

    Full Text Available Nanowire structures have attracted attention in various fields, since new characteristics could be acquired in minute regions. Especially, Anodic Aluminum Oxide (AAO is widely used in the fabrication of nanostructures, which has many nanosized pores and well-organized nano pattern. Using AAO as a template for replication, nanowires with a very high aspect ratio can be fabricated. Herein, we propose a facile method to fabricate a nano-micro hybrid structure using nanowires replicated from AAO, and surface treatment. A polymer resin was coated between Polyethylene terephthalate (PET and the AAO filter, roller pressed, and UV-cured. After the removal of aluminum by using NaOH solution, the nanowires aggregated to form a micropattern. The resulting structure was subjected to various surface treatments to investigate the surface behavior and wettability. As opposed to reported data, UV-ozone treatment can enhance surface hydrophobicity because the UV energy affects the nanowire surface, thus altering the shape of the aggregated nanowires. The hydrophobicity of the surface could be further improved by octadecyltrichlorosilane (OTS coating immediately after UV-ozone treatment. We thus demonstrated that the nano-micro hybrid structure could be formed in the middle of nanowire replication, and then, the shape and surface characteristics could be controlled by surface treatment.

  19. Structural System Identification in the Time Domain using Evolutionary and Behaviorally Inspired Algorithms and their Hybrids

    Directory of Open Access Journals (Sweden)

    S. Sandesh

    2009-12-01

    Full Text Available In this study, parametric identification of structural properties such as stiffness and damping is carried out using acceleration responses in the time domain. The process consists of minimizing the difference between the experimentally measured and theoretically predicted acceleration responses. The unknown parameters of certain numerical models, viz., a ten degree of freedom lumped mass system, a nine member truss and a non-uniform simply supported beam are thus identified. Evolutionary and behaviorally inspired optimization algorithms are used for minimization operations. The performance of their hybrid combinations is also investigated. Genetic Algorithm (GA is a well known evolutionary algorithm used in system identification. Recently Particle Swarm Optimization (PSO, a behaviorally inspired algorithm, has emerged as a strong contender to GA in speed and accuracy. The discrete Ant Colony Optimization (ACO method is yet another behaviorally inspired method studied here. The performance (speed and accuracy of each algorithm alone and in their hybrid combinations such as GA with PSO, ACO with PSO and ACO with GA are extensively investigated using the numerical examples with effects of noise added for realism. The GA+PSO hybrid algorithm was found to give the best performance in speed and accuracy compared to all others. The next best in performance was pure PSO followed by pure GA. ACO performed poorly in all the cases.

  20. A review of the performance and structural considerations of paraffin wax hybrid rocket fuels with additives

    Science.gov (United States)

    Veale, Kirsty; Adali, Sarp; Pitot, Jean; Brooks, Michael

    2017-12-01

    Paraffin wax as a hybrid rocket fuel has not been comprehensively characterised, especially regarding the structural feasibility of the material in launch applications. Preliminary structural testing has shown paraffin wax to be a brittle, low strength material, and at risk of failure under launch loading conditions. Structural enhancing additives have been identified, but their effect on motor performance has not always been considered, nor has any standard method of testing been identified between research institutes. A review of existing regression rate measurement techniques on paraffin wax based fuels and the results obtained with various additives are collated and discussed in this paper. The review includes 2D slab motors that enable visualisation of liquefying fuel droplet entrainment and the effect of an increased viscosity on the droplet entrainment mechanism, which can occur with the addition of structural enhancing polymers. An increased viscosity has been shown to reduce the regression rate of liquefying fuels. Viscosity increasing additives that have been tested include EVA and LDPE. Both these additives increase the structural properties of paraffin wax, where the elongation and UTS are improved. Other additives, such as metal hydrides, aluminium and boron generally offer improvements on the regression rate. However, very little consideration has been given to the structural effects these additives have on the wax grain. A 40% aluminised grain, for example, offers a slight increase in the UTS but reduces the elongation of paraffin wax. Geometrically accurate lab-scale motors have also been used to determine the regression rate properties of various additives in paraffin wax. A concise review of all available regression rate testing techniques and results on paraffin wax based hybrid propellants, as well as existing structural testing data, is presented in this paper.

  1. Cross-bidge Kelvin resistor (CBKR) structures for measurement of low contact resistances

    NARCIS (Netherlands)

    Stavitski, N.; Klootwijk, J.H.; van Zeijl, H.W.; Boksteen, B.K.; Boksteen, B.K.; Kovalgin, Alexeij Y.; Wolters, Robertus A.M.

    2007-01-01

    A convenient test structure for measurement of the specific contact resistance (�?c) of metal-semiconductor junctions is the CBKR structure. During last few decades the parasitic factors which may strongly affect the measurements accuracy for �?c < 10-6 Ω • cm2 have been sufficiently discussed and

  2. Quantitative magneto-optical investigation of superconductor/ferromagnet hybrid structures

    Science.gov (United States)

    Shaw, G.; Brisbois, J.; Pinheiro, L. B. G. L.; Müller, J.; Blanco Alvarez, S.; Devillers, T.; Dempsey, N. M.; Scheerder, J. E.; Van de Vondel, J.; Melinte, S.; Vanderbemden, P.; Motta, M.; Ortiz, W. A.; Hasselbach, K.; Kramer, R. B. G.; Silhanek, A. V.

    2018-02-01

    We present a detailed quantitative magneto-optical imaging study of several superconductor/ferromagnet hybrid structures, including Nb deposited on top of thermomagnetically patterned NdFeB and permalloy/niobium with erasable and tailored magnetic landscapes imprinted in the permalloy layer. The magneto-optical imaging data are complemented with and compared to scanning Hall probe microscopy measurements. Comprehensive protocols have been developed for calibrating, testing, and converting Faraday rotation data to magnetic field maps. Applied to the acquired data, they reveal the comparatively weaker magnetic response of the superconductor from the background of larger fields and field gradients generated by the magnetic layer.

  3. Dynamical Coulomb blockade of the nonlocal conductance in normalmetal/superconductor hybrid structures

    Energy Technology Data Exchange (ETDEWEB)

    Kolenda, Stefan; Wolf, Michael J.; Beckmann, Detlef [Institut fuer Nanotechnologie, KIT, 76021 Karlsruhe (Germany)

    2013-07-01

    In normalmetal/superconductor hybrid structures nonlocal conductance is determined by crossed Andreev reflection (CAR) and elastic cotunneling (EC). This was investigated recently both experimentally and theoretically. Dynamical Coulomb blockade of EC and CAR was predicted theoretically. Here we report on experimental investigations of these effects. We found signatures of dynamical Coulomb blockade in local and nonlocal conductance in the normal state. In the superconducting state, we find s-shaped nonlocal differential conductance curves as a function of bias applied on both contacts. These curves were observed for bias voltages both below and above the gap. We compare our results to theory.

  4. Quantitative magneto-optical investigation of superconductor/ferromagnet hybrid structures.

    Science.gov (United States)

    Shaw, G; Brisbois, J; Pinheiro, L B G L; Müller, J; Blanco Alvarez, S; Devillers, T; Dempsey, N M; Scheerder, J E; Van de Vondel, J; Melinte, S; Vanderbemden, P; Motta, M; Ortiz, W A; Hasselbach, K; Kramer, R B G; Silhanek, A V

    2018-02-01

    We present a detailed quantitative magneto-optical imaging study of several superconductor/ferromagnet hybrid structures, including Nb deposited on top of thermomagnetically patterned NdFeB and permalloy/niobium with erasable and tailored magnetic landscapes imprinted in the permalloy layer. The magneto-optical imaging data are complemented with and compared to scanning Hall probe microscopy measurements. Comprehensive protocols have been developed for calibrating, testing, and converting Faraday rotation data to magnetic field maps. Applied to the acquired data, they reveal the comparatively weaker magnetic response of the superconductor from the background of larger fields and field gradients generated by the magnetic layer.

  5. Detailed Post-Soft Impact Progressive Damage Assessment for Hybrid Structure Jet Engines

    Science.gov (United States)

    Siddens, Aaron; Bayandor, Javid; Celestina, Mark L.

    2014-01-01

    Currently, certification of engine designs for resistance to bird strike is reliant on physical tests. Predictive modeling of engine structural damage has mostly been limited to evaluation of individual forward section components, such as fan blades within a fixed frame of reference, to direct impact with a bird. Such models must be extended to include interactions among engine components under operating conditions to evaluate the full extent of engine damage. This paper presents the results of a study aim to develop a methodology for evaluating bird strike damage in advanced propulsion systems incorporating hybrid composite/metal structures. The initial degradation and failure of individual fan blades struck by a bird were investigated. Subsequent damage to other fan blades and engine components due to resultant violent fan assembly vibrations and fragmentation was further evaluated. Various modeling parameters for the bird and engine components were investigated to determine guidelines for accurately capturing initial damage and progressive failure of engine components. Then, a novel hybrid structure modeling approach was investigated and incorporated into the crashworthiness methodology. Such a tool is invaluable to the process of design, development, and certification of future advanced propulsion systems.

  6. Tunable thermal rectification in graphene/hexagonal boron nitride hybrid structures

    Science.gov (United States)

    Chen, Xue-Kun; Hu, Ji-Wen; Wu, Xi-Jun; Jia, Peng; Peng, Zhi-Hua; Chen, Ke-Qiu

    2018-02-01

    Using non-equilibrium molecular dynamics simulations, we investigate thermal rectification (TR) in graphene/hexagonal boron nitride (h-BN) hybrid structures. Two different structural models, partially substituting graphene into h-BN (CBN) and partially substituting h-BN into graphene (BNC), are considered. It is found that CBN has a significant TR effect while that of BNC is very weak. The observed TR phenomenon can be attributed to the resonance effect between out-of-plane phonons of graphene and h-BN domains in the low-frequency region under negative temperature bias. In addition, the influences of ambient temperature, system size, defect number and substrate interaction are also studied to obtain the optimum conditions for TR. More importantly, the TR ratio could be effectively tuned through chemical and structural diversity. A moderate C/BN ratio and parallel arrangement are found to enhance the TR ratio. Detailed phonon spectra analyses are conducted to understand the thermal transport behavior. This work extends hybrid engineering to 2D materials for achieving TR.

  7. MBE growth of Al/InAs and Nb/InAs superconducting hybrid nanowire structures.

    Science.gov (United States)

    Güsken, Nicholas A; Rieger, Torsten; Zellekens, Patrick; Bennemann, Benjamin; Neumann, Elmar; Lepsa, Mihail I; Schäpers, Thomas; Grützmacher, Detlev

    2017-11-09

    We report the in situ growth of crystalline aluminum (Al) and niobium (Nb) shells on indium arsenide (InAs) nanowires. The nanowires are grown on Si(111) substrates by molecular beam epitaxy (MBE) without foreign catalysts in the vapor-solid (VS) mode. The metal shells are deposited by electron-beam evaporation in a metal MBE. High quality superconductor/semiconductor (SC/SM) hybrid structures such as Al/InAs and Nb/InAs are of interest for ongoing research in the fields of gateable Josephson junctions and quantum information related research. Systematic investigations of the deposition parameters suitable for metal shell growth are conducted. In the case of Al, the substrate temperature, the growth rate and the shell thickness are considered. The substrate temperature as well as the angle of the impinging deposition flux are explored for Nb shells. The core-shell hybrid structures are characterized by electron microscopy and X-ray spectroscopy. Our results show that the substrate temperature is a crucial parameter in enabling the deposition of smooth Al layers. Contrarily, Nb films are less dependent on substrate temperature but are strongly affected by the deposition angle. At a temperature of 200 °C Nb reacts with InAs, dissolving the nanowire crystal. Our investigations result in smooth metal shells exhibiting an impurity and defect free, crystalline SC/InAs interface. Additionally, we find that the SC crystal structure is not affected by stacking faults present in the InAs nanowires.

  8. Effect of graphene on photoluminescence properties of graphene/GeSi quantum dot hybrid structures

    Science.gov (United States)

    Chen, Y. L.; Ma, Y. J.; Chen, D. D.; Wang, W. Q.; Ding, K.; Wu, Q.; Fan, Y. L.; Yang, X. J.; Zhong, Z. Y.; Xu, F.; Jiang, Z. M.

    2014-07-01

    Graphene has been discovered to have two effects on the photoluminescence (PL) properties of graphene/GeSi quantum dot (QD) hybrid structures, which were formed by covering monolayer graphene sheet on the multilayer ordered GeSi QDs sample surfaces. At the excitation of 488 nm laser line, the hybrid structure had a reduced PL intensity, while at the excitation of 325 nm, it had an enhanced PL intensity. The attenuation in PL intensity can be attributed to the transferring of electrons from the conducting band of GeSi QDs to the graphene sheet. The electron transfer mechanism was confirmed by the time resolved PL measurements. For the PL enhancement, a mechanism called surface-plasmon-polariton (SPP) enhanced absorption mechanism is proposed, in which the excitation of SPP in the graphene is suggested. Due to the resonant excitation of SPP by incident light, the absorption of incident light is much enhanced at the surface region, thus leading to more exciton generation and a PL enhancement in the region. The results may be helpful to provide us a way to improve optical properties of low dimensional surface structures.

  9. Structure and weights optimisation of a modified Elman network emotion classifier using hybrid computational intelligence algorithms: a comparative study

    Science.gov (United States)

    Sheikhan, Mansour; Abbasnezhad Arabi, Mahdi; Gharavian, Davood

    2015-10-01

    Artificial neural networks are efficient models in pattern recognition applications, but their performance is dependent on employing suitable structure and connection weights. This study used a hybrid method for obtaining the optimal weight set and architecture of a recurrent neural emotion classifier based on gravitational search algorithm (GSA) and its binary version (BGSA), respectively. By considering the features of speech signal that were related to prosody, voice quality, and spectrum, a rich feature set was constructed. To select more efficient features, a fast feature selection method was employed. The performance of the proposed hybrid GSA-BGSA method was compared with similar hybrid methods based on particle swarm optimisation (PSO) algorithm and its binary version, PSO and discrete firefly algorithm, and hybrid of error back-propagation and genetic algorithm that were used for optimisation. Experimental tests on Berlin emotional database demonstrated the superior performance of the proposed method using a lighter network structure.

  10. A hybrid system identification methodology for wireless structural health monitoring systems based on dynamic substructuring

    Science.gov (United States)

    Dragos, Kosmas; Smarsly, Kay

    2016-04-01

    System identification has been employed in numerous structural health monitoring (SHM) applications. Traditional system identification methods usually rely on centralized processing of structural response data to extract information on structural parameters. However, in wireless SHM systems the centralized processing of structural response data introduces a significant communication bottleneck. Exploiting the merits of decentralization and on-board processing power of wireless SHM systems, many system identification methods have been successfully implemented in wireless sensor networks. While several system identification approaches for wireless SHM systems have been proposed, little attention has been paid to obtaining information on the physical parameters (e.g. stiffness, damping) of the monitored structure. This paper presents a hybrid system identification methodology suitable for wireless sensor networks based on the principles of component mode synthesis (dynamic substructuring). A numerical model of the monitored structure is embedded into the wireless sensor nodes in a distributed manner, i.e. the entire model is segmented into sub-models, each embedded into one sensor node corresponding to the substructure the sensor node is assigned to. The parameters of each sub-model are estimated by extracting local mode shapes and by applying the equations of the Craig-Bampton method on dynamic substructuring. The proposed methodology is validated in a laboratory test conducted on a four-story frame structure to demonstrate the ability of the methodology to yield accurate estimates of stiffness parameters. Finally, the test results are discussed and an outlook on future research directions is provided.

  11. Analysis of hybrid dielectric-plasmonic slot waveguide structures with 3D Fourier Modal Methods

    Science.gov (United States)

    Ctyroky, J.; Kwiecien, P.; Richter, I.

    2013-03-01

    Recently, plasmonic waveguides have been intensively studied as promising basic building blocks for the construction of extremely compact photonic devices with subwavelength characteristic dimensions. A number of different types of plasmonic waveguide structures have been recently proposed, theoretically analyzed, and their properties experimentally verified. The fundamental trade-off in the design of plasmonic waveguides for potential application in information technologies lies in the contradiction between their mode field confinement and propagation loss: the higher confinement, the higher loss, and vice versa. Various definitions of figures of merit of plasmonic waveguides have been also introduced for the characterization of their properties with a single quantity. In this contribution, we theoretically analyze one specific type of a plasmonic waveguide - the hybrid dielectric-loaded plasmonic waveguide, or - as we call it in this paper - the hybrid dielectric-plasmonic slot waveguide, which exhibits very strong field confinement combined with acceptable losses allowing their application in some integrated plasmonic devices. In contrast to the structures analyzed previously, our structure makes use of a single low-index dielectric only. We first define the effective area of this waveguide type, and using waveguide parameters close to the optimum we analyze several waveguide devices as directional couplers, multimode interference couplers (MMI), and the Mach-Zehnder interferometer based on the MMI couplers. For the full-vector 3D analysis of these structures, we use modelling tools developed in-house on the basis of the Fourier Modal Method (FMM). Our results thus serve to a dual purpose: they confirm that (i) these structures represent promising building blocks of plasmonic devices, and (ii) our FMM codes are capable of efficient 3D vector modelling of plasmonic waveguide devices.

  12. Structured oligonucleotides for target indexing to allow single-vessel PCR amplification and solid support microarray hybridization.

    Science.gov (United States)

    Girard, Laurie D; Boissinot, Karel; Peytavi, Régis; Boissinot, Maurice; Bergeron, Michel G

    2015-02-07

    The combination of molecular diagnostic technologies is increasingly used to overcome limitations on sensitivity, specificity or multiplexing capabilities, and provide efficient lab-on-chip devices. Two such techniques, PCR amplification and microarray hybridization are used serially to take advantage of the high sensitivity and specificity of the former combined with high multiplexing capacities of the latter. These methods are usually performed in different buffers and reaction chambers. However, these elaborate methods have high complexity and cost related to reagent requirements, liquid storage and the number of reaction chambers to integrate into automated devices. Furthermore, microarray hybridizations have a sequence dependent efficiency not always predictable. In this work, we have developed the concept of a structured oligonucleotide probe which is activated by cleavage from polymerase exonuclease activity. This technology is called SCISSOHR for Structured Cleavage Induced Single-Stranded Oligonucleotide Hybridization Reaction. The SCISSOHR probes enable indexing the target sequence to a tag sequence. The SCISSOHR technology also allows the combination of nucleic acid amplification and microarray hybridization in a single vessel in presence of the PCR buffer only. The SCISSOHR technology uses an amplification probe that is irreversibly modified in presence of the target, releasing a single-stranded DNA tag for microarray hybridization. Each tag is composed of a 3-nucleotide sequence-dependent segment and a unique "target sequence-independent" 14-nucleotide segment allowing for optimal hybridization with minimal cross-hybridization. We evaluated the performance of five (5) PCR buffers to support microarray hybridization, compared to a conventional hybridization buffer. Finally, as a proof of concept, we developed a multiplexed assay for the amplification, detection, and identification of three (3) DNA targets. This new technology will facilitate the design

  13. Molecular structure of r/GCG/d/TATACGC/ - A DNA-RNA hybrid helix joined to double helical DNA

    Science.gov (United States)

    Wang, A. H.-J.; Fujii, S.; Rich, A.; Van Boom, J. H.; Van Der Marel, G. A.; Van Boeckel, S. A. A.

    1982-01-01

    The molecule r(GCG)d(TATACGC) is self-complementary and forms two DNA-RNA hybrid segments surrounding a central region of double helical DNA; its molecular structure has been solved by X-ray analysis. All three parts of the molecule adopt a conformation which is close to that seen in the 11-fold RNA double helix. The conformation of the ribonucleotides is partly determined by water molecules bridging between the ribose O2' hydroxyl group and cytosine O2. The hybrid-DNA duplex junction contains no structural discontinuities. However, the central DNA TATA sequence has some structural irregularities.

  14. Unexpected structural complexity of supernumerary marker chromosomes characterized by microarray comparative genomic hybridization

    Directory of Open Access Journals (Sweden)

    Hing Anne V

    2008-04-01

    Full Text Available Abstract Background Supernumerary marker chromosomes (SMCs are structurally abnormal extra chromosomes that cannot be unambiguously identified by conventional banding techniques. In the past, SMCs have been characterized using a variety of different molecular cytogenetic techniques. Although these techniques can sometimes identify the chromosome of origin of SMCs, they are cumbersome to perform and are not available in many clinical cytogenetic laboratories. Furthermore, they cannot precisely determine the region or breakpoints of the chromosome(s involved. In this study, we describe four patients who possess one or more SMCs (a total of eight SMCs in all four patients that were characterized by microarray comparative genomic hybridization (array CGH. Results In at least one SMC from all four patients, array CGH uncovered unexpected complexity, in the form of complex rearrangements, that could have gone undetected using other molecular cytogenetic techniques. Although array CGH accurately defined the chromosome content of all but two minute SMCs, fluorescence in situ hybridization was necessary to determine the structure of the markers. Conclusion The increasing use of array CGH in clinical cytogenetic laboratories will provide an efficient method for more comprehensive characterization of SMCs. Improved SMC characterization, facilitated by array CGH, will allow for more accurate SMC/phenotype correlation.

  15. Structural insights into two inorganic-organic hybrids based on chiral amino acids and polyoxomolybdates

    Science.gov (United States)

    Arefian, Mina; Mirzaei, Masoud; Eshtiagh-Hosseini, Hossein

    2018-03-01

    A new chiral inorganic-organic hybrid with the formula (L-His)2(H7CoMo6O24)·6H2O (1), based on natural amino acid and Anderson type polyoxomolybdate was synthesized through mild condition. The chiral L-histidine molecules induced chirality to the whole structure through various types of strong and unconventional hydrogen bond (HB) interactions (CH⋯O, NH⋯O and CH···π interactions), as well as bifurcated hydrogen bonds (BHBs) between L-histidine amino acid, hexamer water cluster molecules, and H7CoMo6O24·xH2O. Following, important non-covalent CH⋯O interactions is investigated in another chiral inorganic-organic hybrid structure, (L-Pro)3(PMo12O40).4.5H2O (2), in detail. The CH⋯O hydrogen bonds lead to a chiral network similar to the DNA strands affording a promising candidate to bio-inorganic studies.

  16. Influence of Hybrid Perovskite Fabrication Methods on Film Formation, Electronic Structure, and Solar Cell Performance

    Science.gov (United States)

    Schnier, Tobias; Emara, Jennifer; Olthof, Selina; Meerholz, Klaus

    2017-01-01

    Hybrid organic/inorganic halide perovskites have lately been a topic of great interest in the field of solar cell applications, with the potential to achieve device efficiencies exceeding other thin film device technologies. Yet, large variations in device efficiency and basic physical properties are reported. This is due to unintentional variations during film processing, which have not been sufficiently investigated so far. We therefore conducted an extensive study of the morphology and electronic structure of a large number of CH3NH3PbI3 perovskite where we show how the preparation method as well as the mixing ratio of educts methylammonium iodide and lead(II) iodide impact properties like film formation, crystal structure, density of states, energy levels, and ultimately the solar cell performance. PMID:28287555

  17. Numerical estimation of structure composition in laser-arc hybrid welded joints

    Directory of Open Access Journals (Sweden)

    W. Piekarska

    2010-10-01

    Full Text Available This work presents results of numerical estimation of the structure composition in laser-arc hybrid welded joints. Temperature field wasobtained by the solution of the heat transfer equation with activity of inner heat sources. Convective motion of liquid metal in the welding pool, latent heat of fusion and latent heat of phase transformation were taken into account in the algorithms for numerical analysis of the temperature field. The volumetric fractions of arising phases were determined on the basis of Johnson - Mehl - Avrami (JMA model for diffusive transformations and Koistinen - Marburger (KM model for martensitic transformation. On the basis of calculated temperature distribution the structure composition in welded joint was numerically estimated, taking into account CHT and CCT diagrams for S355 steel.

  18. Design guideline for Si/organic hybrid solar cell with interdigitated back contact structure

    Science.gov (United States)

    Bimo Prakoso, Ari; Rusli; Li, Zeyu; Lu, Chenjin; Jiang, Changyun

    2018-03-01

    We study the design of Si/organic hybrid (SOH) solar cells with interdigitated back contact (IBC) structure. SOH solar cells formed between n-Si and poly(3,4-ethylenedioxythiophene): polystyrenesulphonate (PEDOT:PSS) is a promising concept that combines the excellent electronic properties of Si with the solution-based processing advantage of an organic polymer. The IBC cell structure is employed to minimize parasitic absorption losses in the organic polymer, eliminate grid shadowing losses, and allow excellent passivation of the front Si surface in one step over a large area. The influence of Si thickness, doping concentration and contact geometry are simulated in this study to optimize the performance of the SOH-IBC solar cell. We found that a high power conversion efficiency of >20% can be achieved for optimized SOH-IBC cell based on a thin c-Si substrate of 40 μm thickness.

  19. Near-field soil-structure interaction analysis using nonlinear hybrid modeling

    International Nuclear Information System (INIS)

    Katayama, I.; Chen, C.; Lee, Y.J.; Jean, W.Y.; Penzien, J.

    1989-01-01

    The hybrid modeling method (Gupta and Penzien 1980) and associated analysis procedure for solving a three-dimensional soil-structure interaction problem was developed by Gupta and Penzien (1981) and Gupta et al.(1982). Subsequently, successive modifications have been made to the original modeling method and analysis procedure allowing more general treatment of the SSI problem (Penzien, 1988). Through many correlation studies of field test data obtained under forced-vibration and earthquake-excitation conditions, it has been shown that the HASSI programs can effectively predict the dynamic response of a soil-structure system, if realistic soil parameters are adopted. In the above, the entire structure-foundation system is considered to respond in a linear fashion. Since the reflected three-dimensional waves at the soil-structure interface decays very rapidly with distance away from the structure (Katayama, 1987 (a)), the response of the soil close to the base of the structure may greatly affect its response; therefore, proper modeling of the non-linear soil behavior characteristic is essential. The nonlinear behavior of near-field soil has been taken into consideration in HASSI-7 by the standard equivalent linearization procedures used in programs SHAKE and FLUSH

  20. Feasibility Study of the Electromagnetic Damper for Cable Structures Using Real-Time Hybrid Simulation.

    Science.gov (United States)

    Jung, Ho-Yeon; Kim, In-Ho; Jung, Hyung-Jo

    2017-10-31

    Cable structure is a major component of long-span bridges, such as cable-stayed and suspension bridges, and it transfers the main loads of bridges to the pylons. As these cable structures are exposed to continuous external loads, such as vehicle and wind loads, vibration control and continuous monitoring of the cable are required. In this study, an electromagnetic (EM) damper was designed and fabricated for vibration control and monitoring of the cable structure. EM dampers, also called regenerative dampers, consist of permanent magnets and coils. The electromagnetic force due to the relative motion between the coil and the permanent magnet can be used to control the vibration of the structure. The electrical energy can be used as a power source for the monitoring system. The effects of the design parameters of the damper were numerically analyzed and the damper was fabricated. The characteristics of the damper were analyzed with various external load changes. Finally, the vibration-control and energy-harvesting performances of the cable structure were evaluated through a hybrid simulation. The vibration-control and energy-harvesting performances for various loads were analyzed and the applicability to the cable structure of the EM damper was evaluated.

  1. Feasibility Study of the Electromagnetic Damper for Cable Structures Using Real-Time Hybrid Simulation

    Directory of Open Access Journals (Sweden)

    Ho-Yeon Jung

    2017-10-01

    Full Text Available Cable structure is a major component of long-span bridges, such as cable-stayed and suspension bridges, and it transfers the main loads of bridges to the pylons. As these cable structures are exposed to continuous external loads, such as vehicle and wind loads, vibration control and continuous monitoring of the cable are required. In this study, an electromagnetic (EM damper was designed and fabricated for vibration control and monitoring of the cable structure. EM dampers, also called regenerative dampers, consist of permanent magnets and coils. The electromagnetic force due to the relative motion between the coil and the permanent magnet can be used to control the vibration of the structure. The electrical energy can be used as a power source for the monitoring system. The effects of the design parameters of the damper were numerically analyzed and the damper was fabricated. The characteristics of the damper were analyzed with various external load changes. Finally, the vibration-control and energy-harvesting performances of the cable structure were evaluated through a hybrid simulation. The vibration-control and energy-harvesting performances for various loads were analyzed and the applicability to the cable structure of the EM damper was evaluated.

  2. Spatial genetic and morphologic structure of wolves and coyotes in relation to environmental heterogeneity in a Canis hybrid zone.

    Science.gov (United States)

    Benson, John F; Patterson, Brent R; Wheeldon, Tyler J

    2012-12-01

    Eastern wolves have hybridized extensively with coyotes and gray wolves and are listed as a 'species of special concern' in Canada. However, a distinct population of eastern wolves has been identified in Algonquin Provincial Park (APP) in Ontario. Previous studies of the diverse Canis hybrid zone adjacent to APP have not linked genetic analysis with field data to investigate genotype-specific morphology or determine how resident animals of different ancestry are distributed across the landscape in relation to heterogeneous environmental conditions. Accordingly, we studied resident wolves and coyotes in and adjacent to APP to identify distinct Canis types, clarify the extent of the APP eastern wolf population beyond the park boundaries and investigate fine-scale spatial genetic structure and landscape-genotype associations in the hybrid zone. We documented three genetically distinct Canis types within the APP region that also differed morphologically, corresponding to putative gray wolves, eastern wolves and coyotes. We also documented a substantial number of hybrid individuals (36%) that were admixed between 2 or 3 of the Canis types. Breeding eastern wolves were less common outside of APP, but occurred in some unprotected areas where they were sympatric with a diverse combination of coyotes, gray wolves and hybrids. We found significant spatial genetic structure and identified a steep cline extending west from APP where the dominant genotype shifted abruptly from eastern wolves to coyotes and hybrids. The genotypic pattern to the south and northwest was a more complex mosaic of alternating genotypes. We modelled genetic ancestry in response to prey availability and human disturbance and found that individuals with greater wolf ancestry occupied areas of higher moose density and fewer roads. Our results clarify the structure of the Canis hybrid zone adjacent to APP and provide unique insight into environmental conditions influencing hybridization dynamics between

  3. Auroral ion acceleration from lower hybrid solitary structures: A summary of sounding rocket observations

    Science.gov (United States)

    Lynch, K. A.; Arnoldy, R. L.; Kintner, P. M.; Schuck, P.; Bonnell, J. W.; Coffey, V.

    In this paper we present a review of sounding rocket observations of the ion acceleration seen in nightside auroral zone lower hybrid solitary structures. Observations from Topaz3, Amicist, and Phaze2 are presented on various spatial scales, including the two-point measurements of the Amicist mission. From this collection of observations we will demonstrate the following characteristics of transverse acceleration of ions (TAI) in lower hybrid solitary structures (LHSS). The ion acceleration process is narrowly confined to 90° pitch angle, in spatially confined regions of up to a few hundred meters across B. The acceleration process does not affect the thermal core of the ambient distribution and does not directly create a measurable effect on the ambient ion population outside the LHSS themselves. This precludes observation with these data of any nonlinear feedback between the ion acceleration and the existence or evolution of the density irregularities on which these LHSS events grow. Within the LHSS region the acceleration process creates a high-energy tail beginning at a few times the thermal ion speed. The ion acceleration events are closely associated with localized wave events. Accelerated ions bursts are also seen without a concurrent observation of a localized wave event, for two possible reasons. In some cases, the pitch angles of the accelerated tail ions are elevated above perpendicular; that is, the acceleration occurred below the observer and the mirror force has begun to act upon the distribution, moving it upward from the source. In other cases, the accelerated ion structure is spatially larger than the wave event structure, and the observation catches only the ion event. The occurrence rate of these ion acceleration events is related to the ambient environment in two ways: its altitude dependence can be modeled with the parameter B2/ne, and it is highest in regions of intense VLF activity. The cumulative ion outflow from these LHSS TAI is

  4. Effect of immerse an organic layer in isopropyl alcohol on characteristics of hybrid photovoltaic structures

    Science.gov (United States)

    Olivares Vargas, A. J.; Cosme, I.; Mansurova, S.; Kosarev, A.; Itzmoyotl, A.

    2017-08-01

    Organic materials have become very important in recent years due to their potential use for photovoltaic applications. Among the main advantages of organic semiconductors are their functional and mechanical flexibility, as well as fabrication simplicity. However, these materials usually afford moderate efficiency in organic photovoltaic devices. On the other hand, hydrogenated amorphous silicon (a-Si:H) is a widely known inorganic semiconductor that compared to their organic counterparts has excellent photogeneration and transport properties and it is suitable for large area fabrication of flexible devices. The idea of combining organic semiconductors and amorphous silicon films in hybrid photovoltaic devices is very attractive due to the possibility to complement the useful properties of both material systems. The photovoltaic devices that we study in this work consist of a p-i-n structure, which is also commonly used in inorganic solar cells. In such kind of structures, the light is mainly absorbed in the intrinsic silicon film and the p- and ntype films are used to create an electric field that separates electrons and holes to produce a photocurrent. In this work, we use an organic material (PEDOT:PSS) to replace the p-type inorganic film in amorphous silicon p-i-n structure. It is widely known, that PEDOT:PSS based organic film is highly transparent and its conductivity can be modified e.g. immerse in a solvent type. Here we present the results of experimental investigation of the effect of isopropanol (IPA) treatments in p-type (PEDOT:PSS) organic layer on characteristics of hybrid solar cell structure.

  5. Structural, mechanical and electronic properties of in-plane 1T/2H phase interface of MoS2 heterostructures

    Directory of Open Access Journals (Sweden)

    Xiaoyan Guo

    2015-09-01

    Full Text Available Two-dimensional (2D molybdenum disulfide (MoS2 phase hybrid system composed by 2H and 1T phase is a natural metal/semiconductor heterostructures and promised a wide range of potential applications. Here, we report the first principle investigations on the structural, mechanical and electronic properties of hybrid system with armchair (AC and zigzag (ZZ interfaces. The ZZ type 1T/2H interface are more energy favorable than AC type interface with 3.39 eV/nm. Similar with that of bulked 1T MoS2, the intrinsic strengths of the heterostructures are lower than that of the bulk 2H, especially for that with ZZ interface. Analysis of density of states shows that the electronic properties gradually transmitted from the metallic 1T phase to the semiconducting 2H phase for the structural abrupt interface. The present theoretical results constitute a useful picture for the 2D electronic devices using current MoS2 1T/2H heterostructures and provide vital insights into the other 2D hybrid materials.

  6. Structural effect of monomer type on properties of copolyimides and copolyimide-silica hybrid materials

    Directory of Open Access Journals (Sweden)

    Kizilkaya Canan

    2015-01-01

    Full Text Available In this work, the effect of two different diamine monomers, containing phosphine oxide, on thermal, mechanical and morphological properties of copolyimides and their hybrid materials was investigated. Gas separation properties of the synthesized copolyimides were also analysed. Two different diamine monomers with phosphine oxide were bis(3-aminophenyl phenylphosphine oxide (BAPPO and bis(3-aminophenoxy-4-phenyl phenylphosphine oxide (m-BAPPO. In the synthesis of copolyimides 3,3’-diamino-diphenyl sulfone (DDS was also used as the diamine, as well as 2,2’-bis(3,4-dicarboxyphenylhexafluoropropane dianhydride (6FDA. Copolyimide films were prepared by thermal imidization. Hybrid materials containing 5 % SiO2 were synthesised further by sol-gel technique. The Fourier-transform infrared spectroscopy (FTIR, Nuclear magnetic resonance spectroscopy (NMR confirmed the expected structure. Dynamic mechanical analysis (DMA demonstrated that m-BAPPO based copolyimides had lower glass transition temperatures (Tg than BAPPO based copolyimides. m-BAPPO containing copolyimide without silica shifted the thermal decomposition temperature to a higher value. The moduli and strength values of BAPPO diamine containing copolyimide and its hybrid were higher than those of m-BAPPO containing materials. The contact angle measurements showed the hydrophobicity. Scanning electron microscope (SEM analysis exhibited the silica particles dispersion in the copolyimides. These copolyimides may be used in the coating industry. The CO2 permeability and the permselectivity were the highest among the other values in this study, when m-BAPPO containing copolyimide in the absence of silica was used. The gas permeabilities obtained from this work were in this decreasing order: PCO2 > PO2 > PN2.

  7. Structural hybrid reliability index and its convergent solving method based on random–fuzzy–interval reliability model

    Directory of Open Access Journals (Sweden)

    Hai An

    2016-08-01

    Full Text Available Aiming to resolve the problems of a variety of uncertainty variables that coexist in the engineering structure reliability analysis, a new hybrid reliability index to evaluate structural hybrid reliability, based on the random–fuzzy–interval model, is proposed in this article. The convergent solving method is also presented. First, the truncated probability reliability model, the fuzzy random reliability model, and the non-probabilistic interval reliability model are introduced. Then, the new hybrid reliability index definition is presented based on the random–fuzzy–interval model. Furthermore, the calculation flowchart of the hybrid reliability index is presented and it is solved using the modified limit-step length iterative algorithm, which ensures convergence. And the validity of convergent algorithm for the hybrid reliability model is verified through the calculation examples in literature. In the end, a numerical example is demonstrated to show that the hybrid reliability index is applicable for the wear reliability assessment of mechanisms, where truncated random variables, fuzzy random variables, and interval variables coexist. The demonstration also shows the good convergence of the iterative algorithm proposed in this article.

  8. Structural studies of RNA-protein complexes: A hybrid approach involving hydrodynamics, scattering, and computational methods.

    Science.gov (United States)

    Patel, Trushar R; Chojnowski, Grzegorz; Astha; Koul, Amit; McKenna, Sean A; Bujnicki, Janusz M

    2017-04-15

    The diverse functional cellular roles played by ribonucleic acids (RNA) have emphasized the need to develop rapid and accurate methodologies to elucidate the relationship between the structure and function of RNA. Structural biology tools such as X-ray crystallography and Nuclear Magnetic Resonance are highly useful methods to obtain atomic-level resolution models of macromolecules. However, both methods have sample, time, and technical limitations that prevent their application to a number of macromolecules of interest. An emerging alternative to high-resolution structural techniques is to employ a hybrid approach that combines low-resolution shape information about macromolecules and their complexes from experimental hydrodynamic (e.g. analytical ultracentrifugation) and solution scattering measurements (e.g., solution X-ray or neutron scattering), with computational modeling to obtain atomic-level models. While promising, scattering methods rely on aggregation-free, monodispersed preparations and therefore the careful development of a quality control pipeline is fundamental to an unbiased and reliable structural determination. This review article describes hydrodynamic techniques that are highly valuable for homogeneity studies, scattering techniques useful to study the low-resolution shape, and strategies for computational modeling to obtain high-resolution 3D structural models of RNAs, proteins, and RNA-protein complexes. Copyright © 2016 The Author(s). Published by Elsevier Inc. All rights reserved.

  9. Hybrid Group IV Nanophotonic Structures Incorporating Diamond Silicon-Vacancy Color Centers.

    Science.gov (United States)

    Zhang, Jingyuan Linda; Ishiwata, Hitoshi; Babinec, Thomas M; Radulaski, Marina; Müller, Kai; Lagoudakis, Konstantinos G; Dory, Constantin; Dahl, Jeremy; Edgington, Robert; Soulière, Veronique; Ferro, Gabriel; Fokin, Andrey A; Schreiner, Peter R; Shen, Zhi-Xun; Melosh, Nicholas A; Vučković, Jelena

    2016-01-13

    We demonstrate a new approach for engineering group IV semiconductor-based quantum photonic structures containing negatively charged silicon-vacancy (SiV(-)) color centers in diamond as quantum emitters. Hybrid diamond-SiC structures are realized by combining the growth of nano- and microdiamonds on silicon carbide (3C or 4H polytype) substrates, with the subsequent use of these diamond crystals as a hard mask for pattern transfer. SiV(-) color centers are incorporated in diamond during its synthesis from molecular diamond seeds (diamondoids), with no need for ion-implantation or annealing. We show that the same growth technique can be used to grow a diamond layer controllably doped with SiV(-) on top of a high purity bulk diamond, in which we subsequently fabricate nanopillar arrays containing high quality SiV(-) centers. Scanning confocal photoluminescence measurements reveal optically active SiV(-) lines both at room temperature and low temperature (5 K) from all fabricated structures, and, in particular, very narrow line widths and small inhomogeneous broadening of SiV(-) lines from all-diamond nanopillar arrays, which is a critical requirement for quantum computation. At low temperatures (5 K) we observe in these structures the signature typical of SiV(-) centers in bulk diamond, consistent with a double lambda. These results indicate that high quality color centers can be incorporated into nanophotonic structures synthetically with properties equivalent to those in bulk diamond, thereby opening opportunities for applications in classical and quantum information processing.

  10. In-plane isotropic magnetic and electrical properties of MnAs/InAs/GaAs (111) B hybrid structure

    Science.gov (United States)

    Islam, Md. Earul; Akabori, Masashi

    2018-03-01

    We characterized in-plane magnetic and electrical properties of MnAs/InAs/GaAs (111) B hybrid structure grown by molecular beam epitaxy (MBE). We observed isotropic easy magnetization in two crystallographic in-plane directions, [ 2 ̅ 110 ] and [ 0 1 ̅ 10 ] of hexagonal MnAs i.e. [ 1 ̅ 10 ] and [ 11 2 ̅ ] of cubic InAs. We also fabricated transmission line model (TLM) devices, and observed almost isotropic electrical properties in two crystallographic in-plane directions, [ 1 ̅ 10 ] and [ 11 2 ̅ ] of cubic InAs. Also we tried to fabricate and characterize lateral spin-valve (LSV) devices from the hybrid structure. We could roughly estimate the spin injection efficiency and the spin diffusion length at room temperature in [ 11 2 ̅ ] direction. We believe that the hybrid structures are helpful to design spintronic device with good flexibility in-plane.

  11. Optical properties of ZnO-nanowire/CdSe-colloidal-quantum-dot hybrid structures

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Dongchao; Richters, Jan-Peter; Dev, Apurba; Voss, Tobias [Semiconductor Optics, Institute of Solid State Physics, University of Bremen (Germany)

    2011-07-01

    One of the research interests in modern nanotechnology is the assembly and study of hybrid heterostructures composed of different materials that offer enhanced properties through the interactions between their different constituents. ZnO nanowires functionalized with colloidal semiconductor quantum dots (QDs) display tailored optical properties due to energy and electron transfer processes between these two components, and have a huge potential for applications in light-emitting and photovoltaic devices. Using a facile method, we synthesized water-soluble CdSe QDs with cadmium acetate and sodium selenosulfate as Cd and Se precursors, respectively. 3-mercaptopropionic acid (MPA) was used to cap the QDs, acting as the stabilizer, making the QDs water soluble and preventing them from agglomeration. TEM measurements demonstrated a narrow size distribution of the as-prepared QDs with the average diameter around 3 nm, consistent with UV-Vis absorption measurements. The carboxylic groups at the outer surface of the MPA-capped CdSe QDs render a tight and uniform attachment onto the surface of ZnO nanowires with high coverage efficiency possible. We studied the optical properties of the hybrid structures by photoluminescence spectroscopy under different temperatures to analyze the energy and electron transfer dynamics between the nanowires and the QDs.

  12. Hierarchically structured graphene-carbon nanotube-cobalt hybrid electrocatalyst for seawater battery

    Science.gov (United States)

    Suh, Dong Hoon; Park, Sul Ki; Nakhanivej, Puritut; Kim, Youngsik; Hwang, Soo Min; Park, Ho Seok

    2017-12-01

    The design of cost-effective and highly active catalysts is a critical challenge. Inspired by the strong points of stability and conductivity of carbon nanotubes (CNTs), high catalytic activity of Co nanoparticles, and rapid ion diffusion and large accessible area of three-dimensional (3D) graphene, we demonstrate a novel strategy to construct a hierarchical hybrid structure consisting of Co/CoOx nanoparticles-incorporated CNT branches onto the 3D reduced graphene oxide (rGO) architecture. The surface-modified 3D rGO by steam activation process has a large surface area and abundant defect sites, which serve as active sites to uniformly grow Co/CoOx nanoparticles. Furthermore, the CNTs preserve their performance stably by encapsulating Co nanoparticles, while the uniformly decorated Co/CoOx nanoparticles exhibit superior electrocatalytic activity toward oxygen evolution/reduction reaction due to highly exposed active sites. Employing the hybrid particle electrocatalyst, the seawater battery operates stably at 0.01 mA cm-2 during 50 cycles, owing to the good electrocatalytic ability.

  13. Structural Characterization of Self-Assembling Hybrid Nanoparticles for Bisphosphonate Delivery in Tumors.

    Science.gov (United States)

    Ristori, Sandra; Grillo, Isabelle; Lusa, Sara; Thamm, Jana; Valentino, Gina; Campani, Virginia; Caraglia, Michele; Steiniger, Frank; Luciani, Paola; De Rosa, Giuseppe

    2018-03-05

    Hybrid self-assembling nanoparticles (hsaNPs) encapsulating bisphosphonates (BPs) recently showed very promising results in preclinic experiments for the treatment of brain tumor. However, the poor knowledge on the architecture of hybrid nanovectors is certainly one of the main reasons hampering further clinical and industrial development of these technologies. Here we propose to combine different techniques, that is, small angle neutron scattering (SANS) and X-ray Sscattering (SAXS), with cryo-electron transmission microscopy (cryo-TEM) to study the architecture of the final hsaNPs as well as of the four components before the assembling process. Data analysis based on SANS and SAXS experiments suggested a multiple compartment architecture of the final product, consisting of two bilayers sourrounding a core. Structures consisting of two shells surrounding an internal core were also observed in the cryo-TEM analysis. Such high resolution insight, also combined with size distribution and zeta potential of the NPs, provides exhaustive characterization of hsaNPs encapsulating BPs, and it is aimed at supporting further their clinical and industrial development.

  14. Denoising GPS-Based Structure Monitoring Data Using Hybrid EMD and Wavelet Packet

    Directory of Open Access Journals (Sweden)

    Lu Ke

    2017-01-01

    Full Text Available High-frequency components are often discarded for data denoising when applying pure wavelet multiscale or empirical mode decomposition (EMD based approaches. Instead, they may raise the problem of energy leakage in vibration signals. Hybrid EMD and wavelet packet (EMD-WP is proposed to denoise Global Positioning System- (GPS- based structure monitoring data. First, field observables are decomposed into a collection of intrinsic mode functions (IMFs with different characteristics. Second, high-frequency IMFs are denoised using the wavelet packet; then the monitoring data are reconstructed using the denoised IMFs together with the remaining low-frequency IMFs. Our algorithm is demonstrated on a synthetic displacement response of a 3-story frame excited by El Centro earthquake along with a set of Gaussian random white noises on different levels added. We find that the hybrid method can effectively weaken the multipath effect with low frequency and can potentially extract vibration feature. However, false modals may still exist by the rest of the noise contained in the high-frequency IMFs and when the frequency of the noise is located in the same band as that of effective vibration. Finally, real GPS observables are implemented to evaluate the efficiency of EMD-WP method in mitigating low-frequency multipath.

  15. Synthesis and characterization of hybrid nanostructures

    Directory of Open Access Journals (Sweden)

    Taleb Mokari

    2011-05-01

    Full Text Available There has been significant interest in the development of multicomponent nanocrystals formed by the assembly of two or more different materials with control over size, shape, composition, and spatial orientation. In particular, the selective growth of metals on the tips of semiconductor nanorods and wires can act to couple the electrical and optical properties of semiconductors with the unique properties of various metals. Here, we outline our progress on the solution-phase synthesis of metal-semiconductor heterojunctions formed by the growth of Au, Pt, or other binary catalytic metal systems on metal (Cd, Pb, Cu-chalcogenide nanostructures. We show the ability to grow the metal on various shapes (spherical, rods, hexagonal prisms, and wires. Furthermore, manipulating the composition of the metal nanoparticles is also shown, where PtNi and PtCo alloys are our main focus. The magnetic and electrical properties of the developed hybrid nanostructures are shown.

  16. Mirror structures above and below the linear instability threshold: Cluster observations, fluid model and hybrid simulations

    Directory of Open Access Journals (Sweden)

    V. Génot

    2009-02-01

    Full Text Available Using 5 years of Cluster data, we present a detailed statistical analysis of magnetic fluctuations associated with mirror structures in the magnetosheath. We especially focus on the shape of these fluctuations which, in addition to quasi-sinusoidal forms, also display deep holes and high peaks. The occurrence frequency and the most probable location of the various types of structures is discussed, together with their relation to local plasma parameters. While these properties have previously been correlated to the β of the plasma, we emphasize here the influence of the distance to the linear mirror instability threshold. This enables us to interpret the observations of mirror structures in a stable plasma in terms of bistability and subcritical bifurcation. The data analysis is supplemented by the prediction of a quasi-static anisotropic MHD model and hybrid numerical simulations in an expanding box aimed at mimicking the magnetosheath plasma. This leads us to suggest a scenario for the formation and evolution of mirror structures.

  17. Liquid-phase synthesis of Ni nanowire/cellulose hybrid structure

    Science.gov (United States)

    Rahmah Shamsuri, Siti; Shiomi, Shohei; Matsubara, Eiichiro

    2018-02-01

    One-dimensional (1D) nanomaterials (nanowires or nanofibers) are superior to conventional zero-dimensional (0D) nanomaterials (nanoparticles). 1D nanomaterials offer not only the benefits of 0D nanomaterials, such as a large surface area and numerous active sites, but also the capability to prepare macroscopic free-standing and flexible structures owing to their formability to form a sheet. For practical applications, it is essential to develop a simple and easy method of synthesizing 1D nanomaterials. In the present work, a nickel nanowire/cellulose hybrid structure is successfully fabricated via a single-batch liquid-phase reduction method under a magnetic field. The product is not a simple 1D or two-dimensional (2D) structure, but an intricately entangled and interconnected three-dimensional (3D) structure. Fine nickel nanowires are grown from nickel nanoparticles that are heterogeneously nucleated on the surface of a cellulose fiber by using its chemical properties that attract nickel ions.

  18. A hybrid design methodology for structuring an Integrated Environmental Management System (IEMS) for shipping business.

    Science.gov (United States)

    Celik, Metin

    2009-03-01

    The International Safety Management (ISM) Code defines a broad framework for the safe management and operation of merchant ships, maintaining high standards of safety and environmental protection. On the other hand, ISO 14001:2004 provides a generic, worldwide environmental management standard that has been utilized by several industries. Both the ISM Code and ISO 14001:2004 have the practical goal of establishing a sustainable Integrated Environmental Management System (IEMS) for shipping businesses. This paper presents a hybrid design methodology that shows how requirements from both standards can be combined into a single execution scheme. Specifically, the Analytic Hierarchy Process (AHP) and Fuzzy Axiomatic Design (FAD) are used to structure an IEMS for ship management companies. This research provides decision aid to maritime executives in order to enhance the environmental performance in the shipping industry.

  19. Structural Characterization and Infrared and Electrical Properties of the New Inorganic-Organic Hybrid Compound

    Directory of Open Access Journals (Sweden)

    A. Oueslati

    2013-01-01

    Full Text Available New inorganic-organic hybrid [(C3H74N]2Hg2Cl6 compound was obtained and characterised by single-crystal X-ray diffraction, infrared, and impedance spectroscopy. The latter crystallizes in the monoclinic system (space group C 2/c, with the following unit cell dimensions: (1 Å, (6 Å, (2 Å, and (2. Besides, its structure was solved using 84860 independent reflections leading to . Electrical properties of the material were studied using impedance spectroscopic technique at different temperatures in the frequency range of 209 Hz to 5 MHz. Detailed analysis of the impedance spectrum suggested that the electrical properties of the material are strongly temperature-dependent. The Nyquist plots clearly showed the presence of bulk and grain boundary effect in the compound.

  20. A hybrid computation method for determining fluctuations of temperature in branched structures

    International Nuclear Information System (INIS)

    Czomber, L.

    1982-01-01

    A hybrid computation method for determining temperature fluctuations at discrete points of slab like geometries is developed on the basis of a new formulation of the finite difference method. For this purpose, a new finite difference method is combined with an exact solution of the heat equation within the range of values of the Laplace transformation. Whereas the exact solution can be applied to arbitraryly large ranges, the finite difference formulation is given for structural ranges which need finer discretization. The boundary conditions of the exact solution are substituted by finite difference terms for the boundary residual flow or an internal heat source, depending on the problem. The resulting system of conditional equations contains only the node parameters of the finite difference method. (orig.) [de

  1. Hybrid Organic/Inorganic Perovskite-Polymer Nanocomposites: Toward the Enhancement of Structural and Electrical Properties.

    Science.gov (United States)

    Privitera, Alberto; Righetto, Marcello; De Bastiani, Michele; Carraro, Francesco; Rancan, Marzio; Armelao, Lidia; Granozzi, Gaetano; Bozio, Renato; Franco, Lorenzo

    2017-12-21

    Hybrid organic/inorganic perovskite nanoparticles (NPs) have garnered remarkable research attention because of their promising photophysical properties. New and interesting properties emerge after combining perovskite NPs with semiconducting materials. Here, we report the synthesis and investigation of a composite material obtained by mixing CH 3 NH 3 PbBr 3 nanocrystals with the semiconducting polymer poly(3-hexylthiophene) (P3HT). By the combination of structural techniques and optical and magnetic spectroscopies we observed multiple effects of the perovskite NPs on the P3HT: (i) an enlargement of P3HT crystalline domains, (ii) a strong p-doping of the P3HT, and (iii) an enhancement of interchain order typical of H-aggregates. These observations open a new avenue toward innovative perovskite NP-based applications.

  2. Hybrid Organic/Inorganic Perovskite–Polymer Nanocomposites: Toward the Enhancement of Structural and Electrical Properties

    KAUST Repository

    Privitera, Alberto

    2017-11-30

    Hybrid organic/inorganic perovskite nanoparticles (NPs) have garnered remarkable research attention because of their promising photophysical properties. New and interesting properties emerge after combining perovskite NPs with semiconducting materials. Here, we report the synthesis and investigation of a composite material obtained by mixing CH3NH3PbBr3 nanocrystals with the semiconducting polymer poly(3-hexylthiophene) (P3HT). By the combination of structural techniques and optical and magnetic spectroscopies we observed multiple effects of the perovskite NPs on the P3HT: (i) an enlargement of P3HT crystalline domains, (ii) a strong p-doping of the P3HT, and (iii) an enhancement of interchain order typical of H-aggregates. These observations open a new avenue toward innovative perovskite NP-based applications.

  3. Experimental investigation of the nature of the magnetoresistance effects in Pd-YIG hybrid structures.

    Science.gov (United States)

    Lin, Tao; Tang, Chi; Alyahayaei, Hamad M; Shi, Jing

    2014-07-18

    In bilayers consisting of Pd and yttrium iron garnet (Y(3)Fe(5)O(12) or YIG), we observe vanishingly small room-temperature conventional anisotropic magnetoresistance but large new magnetoresistance that is similar to the spin Hall magnetoresistance previously reported in Pt-YIG bilayers. We report a temperature dependence study of the two magnetoresistance effects in Pt-YIG bilayers. As the temperature is decreased, the new magnetoresistance shows a peak, whereas the anisotropic magnetoresistance effect starts to appear and increases monotonically. We find that the magnetoresistance peak shifts to lower temperatures in thicker Pd samples, a feature characteristic of the spin current effect. The distinct temperature dependence reveals fundamentally different mechanisms responsible for the two effects in such hybrid structures.

  4. Mechanical properties and production quality of hand-layup and vacuum infusion processed hybrid composite materials for GFRP marine structures

    Science.gov (United States)

    Kim, Sang-Young; Shim, Chun Sik; Sturtevant, Caleb; Kim, Dave (Dae-Wook); Song, Ha Cheol

    2014-09-01

    Glass Fiber Reinforced Plastic (GFRP) structures are primarily manufactured using hand lay-up or vacuum infusion techniques, which are cost-effective for the construction of marine vessels. This paper aims to investigate the mechanical properties and failure mechanisms of the hybrid GFRP composites, formed by applying the hand lay-up processed exterior and the vacuum infusion processed interior layups, providing benefits for structural performance and ease of manufacturing. The hybrid GFRP composites contain one, two, and three vacuum infusion processed layer sets with consistent sets of hand lay-up processed layers. Mechanical properties assessed in this study include tensile, compressive and in-plane shear properties. Hybrid composites with three sets of vacuum infusion layers showed the highest tensile mechanical properties while those with two sets had the highest mechanical properties in compression. The batch homogeneity, for the GFRP fabrication processes, is evaluated using the experimentally obtained mechanical properties

  5. Hybridization, electronic structure and properties of uranium intermetallics: URu 3, URh 3, UPd 3, UIr 3 and UPt 3

    Science.gov (United States)

    Oguchi, Tamio; Freeman, A. J.

    1986-10-01

    Results of fully-relativistic local density energy band calculations for uranium intermetallics, URu 3 URh 3, UPd 3, UIr 3 and UPt 3, are presented. These include energy bands projected by angular momentum and atom type, total and projected densities of states, specific heat mass enhancement factors and Stoner factors, Systematic variations in hybridization between uranium and transition-metal (X) states,particularly U-f and X-d, are found. The effects of crystal structure on the electronic structure of UPt 3 are examined. The f-d hybridization in the observed hexagonal UPt 3 phase is larger than that in the cubic phase. It is shown by inspecting the wavefunctions on the Fermi surface that the large k-dependence of the hybridization results in strong anistropy of the Fermi surface.

  6. Flash NanoPrecipitation as a scalable platform for the production of structured and hybrid nanocolloids

    Science.gov (United States)

    Lee, Victoria; Sosa, Chris; Liu, Rui; Prud'Homme, Robert; Priestley, Rodney

    Geometrically-structured polymer nanocolloids have been widely investigated for their unique properties, which are derived from their anisotropy. Decoration with inorganic nanoparticles in a controlled manner could induce another level of functionality into structured nanocolloids that could enable applications in fields such as re-writeable electronics and biphasic catalysis. Here, Flash NanoPrecipitation (FNP) is demonstrated as a one-step and scalable process platform to manufacture hybrid polymer-inorganic nanocolloids in which one phase is selectively decorated with a metal nanocatalyst by tuning the interactions between the feed ingredients. For instance, by modifying polymer end-group functionality, we are able to tune the location of the metal nanocatalyst, including placement at the Janus nanocolloid circumference. Moreover, the addition of surfactant to the system is shown to transform the Janus nanocolloid structure from spherical to dumbbell or snowman while still maintaining control over nanocatalyst location. Considering the flexibility and continuous nature of the FNP process, it offers an industrial-scale platform for manufacturing of nanomaterials that are anticipated to impact many technologies.

  7. Tunable superconducting critical temperature in ballistic hybrid structures with strong spin-orbit coupling

    Science.gov (United States)

    Simensen, Haakon T.; Linder, Jacob

    2018-02-01

    We present a theoretical description and numerical simulations of the superconducting transition in hybrid structures including strong spin-orbit interactions. The spin-orbit coupling is taken to be of Rashba type for concreteness, and we allow for an arbitrary magnitude of the spin-orbit strength as well as an arbitrary thickness of the spin-orbit coupled layer. This allows us to make contact with the experimentally relevant case of enhanced interfacial spin-orbit coupling via atomically thin heavy metal layers. We consider both interfacial spin-orbit coupling induced by inversion asymmetry in an S/F junction, as well as in-plane spin-orbit coupling in the ferromagnetic region of an S/F/S and an S/F structure. Both the pair amplitudes, local density of states, and critical temperature show dependency on the Rashba strength and, importantly, the orientation of the exchange field. In general, spin-orbit coupling increases the critical temperature of a proximity system where a magnetic field is present, and enhances the superconducting gap in the density of states. We perform a theoretical derivation which explains these results by the appearance of long-ranged singlet correlations. Our results suggest that Tc in ballistic spin-orbit coupled superconducting structures may be tuned by using only a single ferromagnetic layer.

  8. Reduced graphene oxide/ZnO hybrid structure for high-performance photodetection

    Energy Technology Data Exchange (ETDEWEB)

    Darbari, S.; Ahmadi, V., E-mail: v_ahmadi@modares.ac.ir [Tarbiat Modares University, Department of Electrical and Computer Engineering (Iran, Islamic Republic of); Afzali, P.; Abdi, Y. [University of Tehran, Department of Physics (Iran, Islamic Republic of); Feda, M. [Tarbiat Modares University, Department of Electrical and Computer Engineering (Iran, Islamic Republic of)

    2014-12-15

    We report the optoelectronic behavior of a novel reduced graphene oxide (rGO)/ZnO structure which has been realized by photocatalytic reduction of chemically exfoliated GO sheets. Lateral ZnO nanowires, which are grown between interdigital electrodes by a novel plasma-assisted procedure, are utilized as the photocatalyst metal oxide in the presented heterostructure. Raman spectroscopy and FTIR analyses are utilized to show that photocatalytic reduction of GO sheets, with few (less than 5) layers, occurs after about 30 min of UV-illumination. Low-temperature electrical characterizations are applied to demonstrate one-dimensional behavior of the realized rGO ribbons, with an estimated width of around 30 nm. The optoelectronic characteristics of the fabricated rGO/ZnO hybrid structure also lead to high responsivity of about 12 A/W and a sensitivity of about 5 × 10{sup 4−} % (at the bias voltage of −5 V), which entitles the fabricated structure as an efficient photodetector. All in all, our experimental results open up a promising simple approach to fabricate GNR-based devices by assisting lateral ZnO nanowire, without involving nanolithography issues.

  9. AFM Imaging of Hybridization Chain Reaction Mediated Signal Transmission between Two DNA Origami Structures.

    Science.gov (United States)

    Helmig, Sarah; Gothelf, Kurt Vesterager

    2017-10-23

    Signal transfer is central to the controlled exchange of information in biology and advanced technologies. Therefore, the development of reliable, long-range signal transfer systems for artificial nanoscale assemblies is of great scientific interest. We have designed such a system for the signal transfer between two connected DNA nanostructures, using the hybridization chain reaction (HCR). Two sets of metastable DNA hairpins, one of which is immobilized at specific points along tracks on DNA origami structures, are polymerized to form a continuous DNA duplex, which is visible using atomic force microscopy (AFM). Upon addition of a designed initiator, the initiation signal is efficiently transferred more than 200 nm from a specific location on one origami structure to an end point on another origami structure. The system shows no significant loss of signal when crossing from one nanostructure to another and, therefore, has the potential to be applied to larger multi-component DNA assemblies. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Measurements of Effective Schottky Barrier in Inverse Extraordinary Optoconductance Structures

    Science.gov (United States)

    Tran, L. C.; Werner, F. M.; Solin, S. A.; Gilbertson, Adam; Cohen, L. F.

    2013-03-01

    Individually addressable optical sensors with dimensions as low as 250nm, fabricated from metal semiconductor hybrid structures (MSH) of AuTi-GaAs Schottky interfaces, display a transition from resistance decreasing with intensity in micron-scale sensors (Extraordinary Optoconductance, EOC) to resistance increasing with intensity in nano-scale sensors (Inverse Extraordinary Optoconductance I-EOC). I-EOC is attributed to a ballistic to diffusive crossover with the introduction of photo-induced carriers and gives rise to resistance changes of up to 9462% in 250nm devices. We characterize the photo-dependence of the effective Schottky barrier in EOC/I-EOC structures by the open circuit voltage and reverse bias resistance. Under illumination by a 5 mW, 632.8 nm HeNe laser, the barrier is negligible and the Ti-GaAs interface becomes Ohmic. Comparing the behavior of two devices, one with leads exposed, another with leads covered by an opaque epoxy, the variation in Voc with the position of the laser can be attributed to a photovoltaic effect of the lead metal and bulk GaAs. The resistance is unaffected by the photovoltaic offset of the leads, as indicated by the radial symmetry of 2-D resistance maps obtained by rastering a laser across EOC/IEOC devices. SAS has a financial interest in PixelEXX, a start-up company whose mission is to market imaging arrays.

  11. Hybrid Control of Supply Chains: a Structured Exploration from a Systems Perspective

    Directory of Open Access Journals (Sweden)

    Paul W. P. J. Grefen

    2013-07-01

    Full Text Available Supply chains are becoming increasingly complex these days, both in the structure of the chains and in the need for fine-grained, real-time control. This development occurs in many industries, such as manufacturing, logistics, and the service industry. The increasing structural complexity is caused by larger numbers of participating companies in supply chains because of increasing complexity of products and services. Increasing requirements to control are caused by developments like mass-customization, pressure on delivery times, and smaller margins for waste. Maintaining well-structured strategic, tactic, and operational control over these complex supply chains is not an easy task – certainly as they are pressured by end-to-end synchronization requirements and just-in-time demands. Things become even more complex when chains need to be flexible to react to changing requirements to the products or services they deliver. To enable design of well-structured control, clear models of control topologies are required. In this paper, we address this need by exploring supply chain control topologies in an organized fashion. The exploration is based on integrating a supply chain model and a control model in two alternative ways to obtain two extreme models for supply chain control. These two models are next combined to obtain a hybrid chain control model in which control parameters can be adapted to accommodate different circumstances, hence facilitating agility in supply chains and networks. We apply the developed model to a number of case studies to show its usability. The contribution of this paper is the structured analysis of the design space for chain-level control models - not the description of individual new models.

  12. Conjugated polymer P3HT-Au hybrid nanostructures for enhancing photocatalytic activity.

    Science.gov (United States)

    Jana, Bikash; Bhattacharyya, Santanu; Patra, Amitava

    2015-06-21

    Metal-semiconductor nanostructures have been the subject of great interest, mainly due to their interesting optical properties and their potential applications in light harvesting, photocatalysis and photovoltaic devices. Here, we have designed raspberry type organic-inorganic hybrid nanostructures of the poly-3-hexylthiophene (P3HT)-Au nanoparticle (NP) composite by a simple solution based synthetic method. The electronic interaction of semiconducting P3HT polymer nanoparticles with Au nanoparticles exhibits a bathochromic shift of absorption bands and significant photoluminescence quenching of P3HT nanoparticles in this organic-inorganic hybrid system. The photocatalytic activity of this raspberry type hybrid nanostructure is demonstrated under the visible light irradiation and the degradation efficiency is found to be 90.6%. Such organic-inorganic hybrid nanostructures made of a semiconducting polymer and plasmonic nanoparticles could pave the way for designing new optical based materials for applications in photocatalytic and light harvesting systems.

  13. Numerical Study on the Seismic Performance of a Steel–Concrete Hybrid Supporting Structure in Thermal Power Plants

    Directory of Open Access Journals (Sweden)

    Bo Wang

    2018-02-01

    Full Text Available This paper presents the numerical investigation on the seismic performance of a steel–concrete hybrid structure consisting of reinforced concrete (RC tubular columns and steel braced truss with A-shaped steel frames, which is a novel supporting structural system to house air-cooled condensers (ACC in large-capacity thermal power plants (TPPs. First, the finite element (FE modeling approach for this hybrid structure using the software ABAQUS was validated by a range of pseudo-dynamic tests (PDTs performed on a 1/8-scaled sub-structure. The failure process, lateral displacement responses, changing rules of dynamic characteristic parameters and lateral stiffness with increase of peak ground acceleration (PGA were presented here. Then, nonlinear time-history analysis of the prototype structure was carried out. The dynamic characteristics, base shear force, lateral deformation capacity, stiffness deterioration and damage characteristics were investigated. Despite the structural complexity and irregularity, both experimental and numerical results indicate that the overall seismic performance of this steel–concrete hybrid supporting structure meets the seismic design requirements with respect to the high-intensity earthquakes.

  14. Positron annihilation lifetime spectroscopy study on the structural relaxation of phenylmethylsiloxane-modified epoxy hybrids at different aging temperatures

    International Nuclear Information System (INIS)

    Hsu, Chia-Wen; Ma, Chen-Chi M.; Tan, Chung-Sung; Li, Hsun-Tien

    2015-01-01

    The cured network conformations and structural relaxation behaviours of the diglycidyl ether of bisphenol A (DGEBA)-methylhexahydrophthalic anhydride (MHHPA) modified with phenylmethylsiloxane-modified epoxy (PMSE) at different aging temperatures were studied using dynamic mechanical analysis (DMA) and positron annihilation lifetime spectroscopy (PALS). The DMA results revealed that the cured PMSE network can insert into the cured DGEBA network to form interpenetrating polymer networks (IPNs). The structural relaxation behaviours of DGEBA–PMSE-0.4 produced using DGEBA, PMSE, and MHHPA at a ratio of 0.6:0.4:1 by equivalent weight were studied using PALS at 150 °C and 55 °C. The aging-induced free volume relaxation parameters of DGEBA–PMSE-0.4 at 150 °C and 55 °C were investigated using the double additive exponential model and the Kohlrausch–Williams–Watts exponential model. For double additive exponential model, only one relaxation time (ζ) of 584.5 h was found at 150 °C; By contrast, there were two separate relaxation times of 37.4 h (ζ 1 ) and 753.6 h (ζ 2 ) at 55 °C. The ζ 1 of the IPNs hybrid can be attributed to the network relaxation of PMSE, and the ζ 2 can be attributed to the network relaxation of DGEBA at 55 °C. The results suggested the double additive exponential model can effectively predict DGEBA–PMSE hybrid relaxation behaviours. - Highlights: • The cured network conformations of DGEBA–PMSE hybrids were studied using DMA. • The structural relaxation behaviours of DGEBA–PMSE hybrids were studied using PALS. • The cured DGEBA–PMSE hybrids were interpenetrating polymer networks (IPNs). • PALS studies provided a quantitative demonstration of relaxation behaviours. • Double additive exponential model effectively predicted the relaxation times of hybrids

  15. Positron annihilation lifetime spectroscopy study on the structural relaxation of phenylmethylsiloxane-modified epoxy hybrids at different aging temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Chia-Wen [Department of Chemical Engineering, National Tsing Hua University, Hsinchu, Taiwan (China); Material and Chemical Research Laboratories, Industrial Technology Research Institute, Hsinchu, Taiwan (China); Ma, Chen-Chi M., E-mail: ccma@che.nthu.edu.tw [Department of Chemical Engineering, National Tsing Hua University, Hsinchu, Taiwan (China); Tan, Chung-Sung [Department of Chemical Engineering, National Tsing Hua University, Hsinchu, Taiwan (China); Li, Hsun-Tien [Material and Chemical Research Laboratories, Industrial Technology Research Institute, Hsinchu, Taiwan (China)

    2015-07-15

    The cured network conformations and structural relaxation behaviours of the diglycidyl ether of bisphenol A (DGEBA)-methylhexahydrophthalic anhydride (MHHPA) modified with phenylmethylsiloxane-modified epoxy (PMSE) at different aging temperatures were studied using dynamic mechanical analysis (DMA) and positron annihilation lifetime spectroscopy (PALS). The DMA results revealed that the cured PMSE network can insert into the cured DGEBA network to form interpenetrating polymer networks (IPNs). The structural relaxation behaviours of DGEBA–PMSE-0.4 produced using DGEBA, PMSE, and MHHPA at a ratio of 0.6:0.4:1 by equivalent weight were studied using PALS at 150 °C and 55 °C. The aging-induced free volume relaxation parameters of DGEBA–PMSE-0.4 at 150 °C and 55 °C were investigated using the double additive exponential model and the Kohlrausch–Williams–Watts exponential model. For double additive exponential model, only one relaxation time (ζ) of 584.5 h was found at 150 °C; By contrast, there were two separate relaxation times of 37.4 h (ζ{sub 1}) and 753.6 h (ζ{sub 2}) at 55 °C. The ζ{sub 1} of the IPNs hybrid can be attributed to the network relaxation of PMSE, and the ζ{sub 2} can be attributed to the network relaxation of DGEBA at 55 °C. The results suggested the double additive exponential model can effectively predict DGEBA–PMSE hybrid relaxation behaviours. - Highlights: • The cured network conformations of DGEBA–PMSE hybrids were studied using DMA. • The structural relaxation behaviours of DGEBA–PMSE hybrids were studied using PALS. • The cured DGEBA–PMSE hybrids were interpenetrating polymer networks (IPNs). • PALS studies provided a quantitative demonstration of relaxation behaviours. • Double additive exponential model effectively predicted the relaxation times of hybrids.

  16. Chemical and structural changes associated with Cu-catalyzed alkaline-oxidative delignification of hybrid poplar.

    Science.gov (United States)

    Li, Zhenglun; Bansal, Namita; Azarpira, Ali; Bhalla, Aditya; Chen, Charles H; Ralph, John; Hegg, Eric L; Hodge, David B

    2015-01-01

    Alkaline hydrogen peroxide pretreatment catalyzed by Cu(II) 2,2'-bipyridine complexes has previously been determined to substantially improve the enzymatic hydrolysis of woody plants including hybrid poplar as a consequence of moderate delignification. In the present work, cell wall morphological and lignin structural changes were characterized for this pretreatment approach to gain insights into pretreatment outcomes and, specifically, to identify the extent and nature of lignin modification. Through TEM imaging, this catalytic oxidation process was shown to disrupt cell wall layers in hybrid poplar. Cu-containing nanoparticles, primarily in the Cu(I) oxidation state, co-localized with the disrupted regions, providing indirect evidence of catalytic activity whereby soluble Cu(II) complexes are reduced and precipitated during pretreatment. The concentration of alkali-soluble polymeric and oligomeric lignin was substantially higher for the Cu-catalyzed oxidative pretreatment. This alkali-soluble lignin content increased with time during the catalytic oxidation process, although the molecular weight distributions were unaltered. Yields of aromatic monomers (including phenolic acids and aldehydes) were found to be less than 0.2 % (wt/wt) on lignin. Oxidation of the benzylic alcohol in the lignin side-chain was evident in NMR spectra of the solubilized lignin, whereas minimal changes were observed for the pretreatment-insoluble lignin. These results provide indirect evidence for catalytic activity within the cell wall. The low yields of lignin-derived aromatic monomers, together with the detailed characterization of the pretreatment-soluble and pretreatment-insoluble lignins, indicate that the majority of both lignin pools remained relatively unmodified. As such, the lignins resulting from this process retain features closely resembling native lignins and may, therefore, be amenable to subsequent valorization.

  17. Organic-inorganic semiconductor hybrid systems. Structure, morphology, and electronic properties

    Energy Technology Data Exchange (ETDEWEB)

    El Helou, Mira

    2012-08-22

    This dissertation addresses the preparation and characterization of hybrid semiconducting systems combining organic with inorganic materials. Characterization methods used included to determine the structure, morphology, and thermal stability comprised X-ray diffraction (XRD), atomic force microscopy (AFM), thermal desorption spectroscopy (TDS), and X-ray photoelectron spectroscopy (XPS). One organic-inorganic semiconducting system was pentacene (C{sub 22}H{sub 14}) and zinc oxide. This interface was investigated in detail for pentacene on an oxygen-terminated zinc oxide surface, i.e. ZnO(000 anti 1). An extended study on the promising p-n junction was carried out for pentacene on ZnO with different orientations which exhibit different chemical and structural characteristics: ZnO(000 anti 1), ZnO(0001), and ZnO(10 anti 10). Moreover, the organic crystal structure of pentacene was selectively tuned by carefully choosing the substrate temperature. This defined interface with a physisorbed pentacene layer on ZnO was characterized by optical absorption which depends on the temperature of the measured system, the pentacene film thickness, and the molecular orientation and packing. The high quality of the pentacene films allowed in one case to characterize the Davydov splitting by linear polarized light focused on a single crystallite. Another subject in the field of organic-inorganic hybrid materials comprised conjugated dithiols used as self-assembled monolayers (SAMs) for immobilizing semiconducting CdS nanoparticles (NPs) on Au substrates. It was demonstrated that an appropriate selection and preparation of the conjugated SAMs is crucial for building up a light-addressable potentiometric sensor with a sufficient efficiency. An optimized electron transfer was achieved with SAMs of long range ordering, high stability, and adequate conductivity. This was examined for different linkers and was best for stilbenedithiol immobilized in solution at higher temperatures. Due

  18. Modular Hybrid Energy Concept Employing a Novel Control Structure Based on a Simple Analog System

    Directory of Open Access Journals (Sweden)

    PETREUS, D.

    2016-05-01

    Full Text Available This paper proposes a novel control topology which enables the setup of a low cost analog system leading to the implementation of a modular energy conversion system. The modular concept is based on hybrid renewable energy (solar and wind and uses high voltage inverters already available on the market. An important feature of the proposed topology is a permanently active current loop, which assures short circuit protection and simplifies the control loops compensation. The innovative analogue solution of the control structure is based on a dedicated integrated circuit (IC for power factor correction (PFC circuits, used in a new configuration, to assure an efficient inverter start-up. The energy conversion system (control structure and maximum power point tracking algorithm is simulated using a new macromodel-based concept, which reduces the usual computational burden of the simulator and achieves high processing speed. The proposed novel system is presented in this article from concept, through the design and implementation stages, is verified through simulation and is validated by experimental results.

  19. Geographically distributed hybrid testing & collaboration between geotechnical centrifuge and structures laboratories

    Science.gov (United States)

    Ojaghi, Mobin; Martínez, Ignacio Lamata; Dietz, Matt S.; Williams, Martin S.; Blakeborough, Anthony; Crewe, Adam J.; Taylor, Colin A.; Madabhushi, S. P. Gopal; Haigh, Stuart K.

    2018-01-01

    Distributed Hybrid Testing (DHT) is an experimental technique designed to capitalise on advances in modern networking infrastructure to overcome traditional laboratory capacity limitations. By coupling the heterogeneous test apparatus and computational resources of geographically distributed laboratories, DHT provides the means to take on complex, multi-disciplinary challenges with new forms of communication and collaboration. To introduce the opportunity and practicability afforded by DHT, here an exemplar multi-site test is addressed in which a dedicated fibre network and suite of custom software is used to connect the geotechnical centrifuge at the University of Cambridge with a variety of structural dynamics loading apparatus at the University of Oxford and the University of Bristol. While centrifuge time-scaling prevents real-time rates of loading in this test, such experiments may be used to gain valuable insights into physical phenomena, test procedure and accuracy. These and other related experiments have led to the development of the real-time DHT technique and the creation of a flexible framework that aims to facilitate future distributed tests within the UK and beyond. As a further example, a real-time DHT experiment between structural labs using this framework for testing across the Internet is also presented.

  20. SAGA: a hybrid search algorithm for Bayesian Network structure learning of transcriptional regulatory networks.

    Science.gov (United States)

    Adabor, Emmanuel S; Acquaah-Mensah, George K; Oduro, Francis T

    2015-02-01

    Bayesian Networks have been used for the inference of transcriptional regulatory relationships among genes, and are valuable for obtaining biological insights. However, finding optimal Bayesian Network (BN) is NP-hard. Thus, heuristic approaches have sought to effectively solve this problem. In this work, we develop a hybrid search method combining Simulated Annealing with a Greedy Algorithm (SAGA). SAGA explores most of the search space by undergoing a two-phase search: first with a Simulated Annealing search and then with a Greedy search. Three sets of background-corrected and normalized microarray datasets were used to test the algorithm. BN structure learning was also conducted using the datasets, and other established search methods as implemented in BANJO (Bayesian Network Inference with Java Objects). The Bayesian Dirichlet Equivalence (BDe) metric was used to score the networks produced with SAGA. SAGA predicted transcriptional regulatory relationships among genes in networks that evaluated to higher BDe scores with high sensitivities and specificities. Thus, the proposed method competes well with existing search algorithms for Bayesian Network structure learning of transcriptional regulatory networks. Copyright © 2014 Elsevier Inc. All rights reserved.

  1. A Hybrid Vector Quantization Combining a Tree Structure and a Voronoi Diagram

    Directory of Open Access Journals (Sweden)

    Yeou-Jiunn Chen

    2014-01-01

    Full Text Available Multimedia data is a popular communication medium, but requires substantial storage space and network bandwidth. Vector quantization (VQ is suitable for multimedia data applications because of its simple architecture, fast decoding ability, and high compression rate. Full-search VQ can typically be used to determine optimal codewords, but requires considerable computational time and resources. In this study, a hybrid VQ combining a tree structure and a Voronoi diagram is proposed to improve VQ efficiency. To efficiently reduce the search space, a tree structure integrated with principal component analysis is proposed, to rapidly determine an initial codeword in low-dimensional space. To increase accuracy, a Voronoi diagram is applied to precisely enlarge the search space by modeling relations between each codeword. This enables an optimal codeword to be efficiently identified by rippling an optimal neighbor from parts of neighboring Voronoi regions. The experimental results demonstrated that the proposed approach improved VQ performance, outperforming other approaches. The proposed approach also satisfies the requirements of handheld device application, namely, the use of limited memory and network bandwidth, when a suitable number of dimensions in principal component analysis is selected.

  2. Numerical model for the analysis of unbounded prestressed structures using the hybrid type finite element method

    International Nuclear Information System (INIS)

    Barbieri, R.A.; Gastal, F.P.S.L.; Filho, A.C.

    2005-01-01

    Unbounded prestressed concrete has a growing importance all over the world and may be an useful technique for the structures involved in the construction of nuclear facilities. The absence of bonding means no strain compatibility so that equations developed for reinforced concrete are no longer valid. Practical estimates about the ultimate stress in the unbounded tendons may be obtained with empirical or numerical methods only. In order to contribute to the understanding on the behaviour of unbounded prestressed concrete members, a numerical model has been developed using a hybrid type finite element formulation for planar frame structures. Instead of short elements, as in the conventional finite element formulation, long elements may be used, improving computational efficiency. A further advantage is that the curvature variation within the element is obtained with higher accuracy if compared to the traditional formulation. This feature is important for unbounded tendons since its stresses depend on the whole member deformation. Second order effects in the planar frame are considered with either Updated or Partially Updated Lagrangian approaches. Instantaneous and time dependent behaviour as well as cyclic loads are considered too. Comparison with experimental results for prestressed concrete beams shows the adequacy of the proposed model. (authors)

  3. Rapid discovery of inhibitors of Toxoplasma gondii using hybrid structure-based computational approach

    Science.gov (United States)

    Kortagere, Sandhya; Mui, Ernest; McLeod, Rima; Welsh, William J.

    2011-05-01

    Toxoplasma (T.) gondii, the causative agent of toxoplasmosis, is a ubiquitous opportunistic pathogen that infects individuals worldwide, and is a leading cause of severe congenital neurologic and ocular disease in humans. No vaccine to protect humans is available, and hypersensitivity and toxicity limit the use of the few available medicines. Therefore, safer and more effective medicines to treat toxoplasmosis are urgently needed. Using the Hybrid Structure Based (HSB) method, we have previously identified small molecule inhibitors of P. falciparum that seem to target a novel protein-protein interaction between the Myosin tail interacting protein and myosin light chain. This pathway has been hypothesized to be involved in invasion of host erythrocytes by the parasite and is broadly conserved among the apicomplexans. Guided by similar computational drug design approaches, we investigated this series of small molecules as potential inhibitors of T. gondii. Compound C3-21, identified as the most active inhibitor in this series, exhibited an IC50 value 500 nM against T. gondii. Among the 16 structural analogs of C3-21 tested thus far, nine additional compounds were identified with IC50 values <10.0 μM. In vitro assays have revealed that C3-21 markedly limits intracellular growth of T. gondii tachyzoites, but has no effect on host cell human foreskin fibroblasts (HFF) at concentrations more than a log greater than the concentration that inhibits the parasites.

  4. Analysis of SMA Hybrid Composite Structures in MSC.Nastran and ABAQUS

    Science.gov (United States)

    Turner, Travis L.; Patel, Hemant D.

    2005-01-01

    A thermoelastic constitutive model for shape memory alloy (SMA) actuators and SMA hybrid composite (SMAHC) structures was recently implemented in the commercial finite element codes MSC.Nastran and ABAQUS. The model may be easily implemented in any code that has the capability for analysis of laminated composite structures with temperature dependent material properties. The model is also relatively easy to use and requires input of only fundamental engineering properties. A brief description of the model is presented, followed by discussion of implementation and usage in the commercial codes. Results are presented from static and dynamic analysis of SMAHC beams of two types; a beam clamped at each end and a cantilever beam. Nonlinear static (post-buckling) and random response analyses are demonstrated for the first specimen. Static deflection (shape) control is demonstrated for the cantilever beam. Approaches for modeling SMAHC material systems with embedded SMA in ribbon and small round wire product forms are demonstrated and compared. The results from the commercial codes are compared to those from a research code as validation of the commercial implementations; excellent correlation is achieved in all cases.

  5. Active structural control of a floating wind turbine with a stroke-limited hybrid mass damper

    Science.gov (United States)

    Hu, Yaqi; He, Erming

    2017-12-01

    Floating wind turbines are subjected to more severe structural loads than fixed-bottom wind turbines due to additional degrees of freedom (DOFs) of their floating foundations. It's a promising way of using active structural control method to improve the structural responses of floating wind turbines. This paper investigates an active vibration control strategy for a barge-type floating wind turbine by setting a stroke-limited hybrid mass damper (HMD) in the turbine's nacelle. Firstly, a contact nonlinear modeling method for the floating wind turbine with clearance between the HMD and the stroke limiters is presented based on Euler-Lagrange's equations and an active control model of the whole system is established. The structural parameters are validated for the active control model and an equivalent load coefficient method is presented for identifying the wind and wave disturbances. Then, a state-feedback linear quadratic regulator (LQR) controller is designed to reduce vibration and loads of the wind turbine, and two optimization methods are combined to optimize the weighting coefficients when considering the stroke of the HMD and the active control power consumption as constraints. Finally, the designed controllers are implemented in high fidelity simulations under five typical wind and wave conditions. The results show that active HMD control strategy is shown to be achievable and the designed controllers could further reduce more vibration and loads of the wind turbine under the constraints of stroke limitation and power consumption. "V"-shaped distribution of the TMD suppression effect is inconsistent with the Weibull distribution in practical offshore floating wind farms, and the active HMD control could overcome this shortcoming of the passive TMD.

  6. Light Intensity Influence on the Effective Schottky Barrier Height in Extraordinary Optoconductance (EOC) Structures

    Science.gov (United States)

    Werner, F. M.; Tran, L. C.; Solin, S. A.

    2013-03-01

    Novel micro to nanoscale metal-semiconductor-hybrid (MSH) structures capable of room temperature light detection have been previously reported and classified as Extraordinary Optoconductance (EOC) devices. The devices are square stacked structures, with a Au-Ti shunt forming a Schottky-Interface with an n-doped Ga-As mesa. Resistance measurements were taken by a 4-point van-der Pauw method to remove contact and lead resistance and eliminate DC offsets. The device's resistance changes as light incident on the surface of the structure modifies the charge density within the body of the device. The change in charge density changes the effective Schottky Barrier height and shifts the measured 4 point resistance of the heterogeneous structure. We investigate the dependence of the effective Schottky Barrier height on the incident intensity of light by measuring the open circuit voltage under various intensities of optical perturbation at room temperature. The barrier height is negligible and the interface ohmic under HeNe laser 632.8 nm illumination at a power density of 636 mW/cm2, allowing the flow of current through the shunt. This device performance will be contrasted with that of an FET, where current does not propagate through the gate. SAS has a financial interest in PixelEXX, a start-up company whose mission is to market imaging arrays.

  7. Structure-property effects of novel bioresorbable hybrid structures with controlled release of analgesic drugs for wound healing applications.

    Science.gov (United States)

    Shemesh, Maoz; Zilberman, Meital

    2014-03-01

    Over the last decades, wound dressings have developed from the traditional gauze dressing to tissue-engineered scaffolds. A wound dressing should ideally maintain a moist environment at the wound surface, allow gas exchange, act as a barrier to micro-organisms and remove excess exudates. In order to provide these characteristics, we developed and studied bioresorbable hybrid structures which combine a synthetic porous drug-loaded top layer with a spongy collagen sublayer. The top layer, prepared using the freeze-drying of inverted emulsions technique, was loaded with the analgesic drugs ibuprofen or bupivacaine, for controlled release to the wound site. Our investigation focused on the effects of the emulsion's parameters on the microstructure and on the resulting drug-release profile, as well as on the physical and mechanical properties. The structure of the semi-occlusive top layer enables control over vapor transmission, in addition to strongly affecting the drug release profile. Release of the analgesic drugs lasted from several days to more than 100 days. Higher organic:aqueous phase ratios and polymer contents reduced the burst release of both drugs and prolonged their release due to a lower porosity. The addition of reinforcing fibers to this layer improved the mechanical properties. Good binding of the two components, PDLGA and collagen, was achieved due to our special method of preparation, which enables a third interfacial layer in which both materials are mixed to create an "interphase". These new PDLGA/collagen structures demonstrated a promising potential for use in various wound healing applications. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  8. Angular structure of jet quenching within a hybrid strong/weak coupling model

    Energy Technology Data Exchange (ETDEWEB)

    Casalderrey-Solana, Jorge [Rudolf Peierls Centre for Theoretical Physics, University of Oxford,1 Keble Road, Oxford OX1 3NP (United Kingdom); Departament de Física Quàntica i Astrofísica & Institut de Ciències del Cosmos (ICC),Universitat de Barcelona, Martí i Franquès 1, 08028 Barcelona (Spain); Gulhan, Doga Can [CERN, EP Department,CH-1211 Geneva 23 (Switzerland); Milhano, José Guilherme [CENTRA, Instituto Superior Técnico, Universidade de Lisboa,Av. Rovisco Pais, P-1049-001 Lisboa (Portugal); Laboratório de Instrumentação e Física Experimental de Partículas (LIP),Av. Elias Garcia 14-1, P-1000-149 Lisboa (Portugal); Theoretical Physics Department, CERN,Geneva (Switzerland); Pablos, Daniel [Departament de Física Quàntica i Astrofísica & Institut de Ciències del Cosmos (ICC),Universitat de Barcelona, Martí i Franquès 1, 08028 Barcelona (Spain); Rajagopal, Krishna [Center for Theoretical Physics, Massachusetts Institute of Technology,Cambridge, MA 02139 (United States)

    2017-03-27

    Within the context of a hybrid strong/weak coupling model of jet quenching, we study the modification of the angular distribution of the energy within jets in heavy ion collisions, as partons within jet showers lose energy and get kicked as they traverse the strongly coupled plasma produced in the collision. To describe the dynamics transverse to the jet axis, we add the effects of transverse momentum broadening into our hybrid construction, introducing a parameter K≡q̂/T{sup 3} that governs its magnitude. We show that, because of the quenching of the energy of partons within a jet, even when K≠0 the jets that survive with some specified energy in the final state are narrower than jets with that energy in proton-proton collisions. For this reason, many standard observables are rather insensitive to K. We propose a new differential jet shape ratio observable in which the effects of transverse momentum broadening are apparent. We also analyze the response of the medium to the passage of the jet through it, noting that the momentum lost by the jet appears as the momentum of a wake in the medium. After freezeout this wake becomes soft particles with a broad angular distribution but with net momentum in the jet direction, meaning that the wake contributes to what is reconstructed as a jet. This effect must therefore be included in any description of the angular structure of the soft component of a jet. We show that the particles coming from the response of the medium to the momentum and energy deposited in it leads to a correlation between the momentum of soft particles well separated from the jet in angle with the direction of the jet momentum, and find qualitative but not quantitative agreement with experimental data on observables designed to extract such a correlation. More generally, by confronting the results that we obtain upon introducing transverse momentum broadening and the response of the medium to the jet with available jet data, we highlight the

  9. The contribution of co-transcriptional RNA:DNA hybrid structures to DNA damage and genome instability.

    Science.gov (United States)

    Hamperl, Stephan; Cimprich, Karlene A

    2014-07-01

    Accurate DNA replication and DNA repair are crucial for the maintenance of genome stability, and it is generally accepted that failure of these processes is a major source of DNA damage in cells. Intriguingly, recent evidence suggests that DNA damage is more likely to occur at genomic loci with high transcriptional activity. Furthermore, loss of certain RNA processing factors in eukaryotic cells is associated with increased formation of co-transcriptional RNA:DNA hybrid structures known as R-loops, resulting in double-strand breaks (DSBs) and DNA damage. However, the molecular mechanisms by which R-loop structures ultimately lead to DNA breaks and genome instability is not well understood. In this review, we summarize the current knowledge about the formation, recognition and processing of RNA:DNA hybrids, and discuss possible mechanisms by which these structures contribute to DNA damage and genome instability in the cell. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Schottky diodes between Bi2S3 nanorods and metal nanoparticles in a polymer matrix as hybrid bulk-heterojunction solar cells

    International Nuclear Information System (INIS)

    Saha, Sudip K.; Pal, Amlan J.

    2015-01-01

    We report the use of metal-semiconductor Schottky junctions in a conjugated polymer matrix as solar cells. The Schottky diodes, which were formed between Bi 2 S 3 nanorods and gold nanoparticles, efficiently dissociated photogenerated excitons. The bulk-heterojunction (BHJ) devices based on such metal-semiconductor Schottky diodes in a polymer matrix therefore acted as an efficient solar cell as compared to the devices based on only the semiconductor nanorods in the polymer matrix or when gold nanoparticles were added separately to the BHJs. In the latter device, gold nanoparticles offered plasmonic enhancement due to an increased cross-section of optical absorption. We report growth and characteristics of the Schottky junctions formed through an intimate contact between Bi 2 S 3 nanorods and gold nanoparticles. We also report fabrication and characterization of BHJ solar cells based on such heterojunctions. We highlight the benefit of using metal-semiconductor Schottky diodes over only inorganic semiconductor nanorods or quantum dots in a polymer matrix in forming hybrid BHJ solar cells

  11. Protein loop modeling using a new hybrid energy function and its application to modeling in inaccurate structural environments.

    Directory of Open Access Journals (Sweden)

    Hahnbeom Park

    Full Text Available Protein loop modeling is a tool for predicting protein local structures of particular interest, providing opportunities for applications involving protein structure prediction and de novo protein design. Until recently, the majority of loop modeling methods have been developed and tested by reconstructing loops in frameworks of experimentally resolved structures. In many practical applications, however, the protein loops to be modeled are located in inaccurate structural environments. These include loops in model structures, low-resolution experimental structures, or experimental structures of different functional forms. Accordingly, discrepancies in the accuracy of the structural environment assumed in development of the method and that in practical applications present additional challenges to modern loop modeling methods. This study demonstrates a new strategy for employing a hybrid energy function combining physics-based and knowledge-based components to help tackle this challenge. The hybrid energy function is designed to combine the strengths of each energy component, simultaneously maintaining accurate loop structure prediction in a high-resolution framework structure and tolerating minor environmental errors in low-resolution structures. A loop modeling method based on global optimization of this new energy function is tested on loop targets situated in different levels of environmental errors, ranging from experimental structures to structures perturbed in backbone as well as side chains and template-based model structures. The new method performs comparably to force field-based approaches in loop reconstruction in crystal structures and better in loop prediction in inaccurate framework structures. This result suggests that higher-accuracy predictions would be possible for a broader range of applications. The web server for this method is available at http://galaxy.seoklab.org/loop with the PS2 option for the scoring function.

  12. PLLA-collagen and PLLA-gelatin hybrid scaffolds with funnel-like porous structure for skin tissue engineering.

    Science.gov (United States)

    Lu, Hongxu; Oh, Hwan Hee; Kawazoe, Naoki; Yamagishi, Kozo; Chen, Guoping

    2012-12-01

    In skin tissue engineering, a three-dimensional porous scaffold is necessary to support cell adhesion and proliferation and to guide cells moving into the repair area in the wound healing process. Structurally, the porous scaffold should have an open and interconnected porous architecture to facilitate homogenous cell distribution. Moreover, the scaffolds should be mechanically strong to protect deformation during the formation of new skin. In this study, the hybrid scaffolds were prepared by forming funnel-like collagen or gelatin sponge on a woven poly(l-lactic acid) (PLLA) mesh. The hybrid scaffolds combined the advantages of both collagen or gelatin (good cell-interactions) and PLLA mesh (high mechanical strength). The hybrid scaffolds were used to culture dermal fibroblasts for dermal tissue engineering. The funnel-like porous structure promoted homogeneous cell distribution and extracellular matrix production. The PLLA mesh reinforced the scaffold to avoid deformation. Subcutaneous implantation showed that the PLLA-collagen and PLLA-gelatin scaffolds promoted the regeneration of dermal tissue and epidermis and reduced contraction during the formation of new tissue. These results indicate that funnel-like hybrid scaffolds can be used for skin tissue regeneration.

  13. Nanoscale analysis of structural and chemical changes in aged hybrid Pt/NbOx/C fuel cell catalysts

    Science.gov (United States)

    Chinchilla, Lidia; Rossouw, David; Trefz, Tyler; Susac, Darija; Kremliakova, Natalia; Botton, Gianluigi A.

    2017-07-01

    We characterize the structural and chemical changes that take place in an electrochemically tested proton-exchange fuel cell cathode material composed of platinum nanoparticles on a niobium oxide-carbon black hybrid support. Two hybrid catalysts with different niobium oxide content (5 wt% and 12 wt%) are compared at the beginning and end of potential cycling. We observe an overall increase in the particle size of the hybrid catalysts after potential cycling, mediated by Ostwald ripening process. The general nanostructure of the catalysts was composed of small Pt-rich particles that were linked to niobium oxide particles. Nanoscale and microscale spectroscopy of the pristine materials reveals several co-existing oxidized forms of niobium (5+, 4+, 2+) in the systems; the most predominant being Nb(V). The study of the energy loss near-edge structure of the Niobium L2,3 edge of catalysts after being subjected to accelerated stress test (AST) potential cycles provides clues on the evolution of niobium oxides (NbOx), in which the relative distribution of Nb(V) decreases, while the number of Nb particles in lower oxidation states slightly increases. Furthermore, energy-dispersive spectroscopy reveals that the content of Nb decreased after cycling, implying that the loss of NbOx eventually altered the fraction of linked Pt-NbOx sites. The observed nanoscale catalyst changes and the presence of the NbOx may have important implications for developing an alternative design for improved hybrid catalyst materials.

  14. PLLA–collagen and PLLA–gelatin hybrid scaffolds with funnel-like porous structure for skin tissue engineering

    Science.gov (United States)

    Lu, Hongxu; Oh, Hwan Hee; Kawazoe, Naoki; Yamagishi, Kozo; Chen, Guoping

    2012-01-01

    In skin tissue engineering, a three-dimensional porous scaffold is necessary to support cell adhesion and proliferation and to guide cells moving into the repair area in the wound healing process. Structurally, the porous scaffold should have an open and interconnected porous architecture to facilitate homogenous cell distribution. Moreover, the scaffolds should be mechanically strong to protect deformation during the formation of new skin. In this study, the hybrid scaffolds were prepared by forming funnel-like collagen or gelatin sponge on a woven poly(l-lactic acid) (PLLA) mesh. The hybrid scaffolds combined the advantages of both collagen or gelatin (good cell-interactions) and PLLA mesh (high mechanical strength). The hybrid scaffolds were used to culture dermal fibroblasts for dermal tissue engineering. The funnel-like porous structure promoted homogeneous cell distribution and extracellular matrix production. The PLLA mesh reinforced the scaffold to avoid deformation. Subcutaneous implantation showed that the PLLA–collagen and PLLA–gelatin scaffolds promoted the regeneration of dermal tissue and epidermis and reduced contraction during the formation of new tissue. These results indicate that funnel-like hybrid scaffolds can be used for skin tissue regeneration. PMID:27877537

  15. Carbon fiber/Co9S8 nanotube arrays hybrid structures for flexible quantum dot-sensitized solar cells.

    Science.gov (United States)

    Guo, Wenxi; Chen, Chang; Ye, Meidan; Lv, Miaoqiang; Lin, Changjian

    2014-04-07

    Recently, hybrid carbon materials and inorganic nanocrystals have received an intensive amount of attention and have opened up an exciting new field in the design and fabrication of high-performance catalysts. Here we present a novel kind of hybrid counter electrode (CE) consisting of a carbon fiber (CF) and Co9S8 nanotube arrays (NTs) for fiber-shaped flexible quantum dot-sensitized solar cells (QDSSCs). The growth mechanisms of Co(CO3)0.35Cl0.20(OH)1.10 nanowire arrays (NWs) on the CFs were discussed, and the catalytic activity of the CF, Pt and Co9S8/CF hybrid structure (Co9S8@CF) were elucidated systematically as well. An absolute energy conversion efficiency of 3.79% has been demonstrated under 100 mW cm(-2) AM 1.5 illumination by using Co9S8@CF as a CE. This work not only demonstrates an innovative approach for growing cobalt sulfide NTs on flexible substrates that can be applied in flexible devices for energy harvesting and storage, but also provides a kind of hybrid structure and high-efficiency CE for QDSSCs.

  16. Planar structured perovskite solar cells by hybrid physical chemical vapor deposition with optimized perovskite film thickness

    Science.gov (United States)

    Wei, Xiangyang; Peng, Yanke; Jing, Gaoshan; Cui, Tianhong

    2018-05-01

    The thickness of perovskite absorber layer is a critical parameter to determine a planar structured perovskite solar cell’s performance. By modifying the spin coating speed and PbI2/N,N-dimethylformamide (DMF) solution concentration, the thickness of perovskite absorber layer was optimized to obtain high-performance solar cells. Using a PbI2/DMF solution of 1.3 mol/L, maximum power conversion efficiency (PCE) of a perovskite solar cell is 15.5% with a perovskite film of 413 nm at 5000 rpm, and PCE of 14.3% was also obtained for a solar cell with a perovskite film of 182 nm thick. It is derived that higher concentration of PbI2/DMF will result in better perovskite solar cells. Additionally, these perovskite solar cells are highly uniform. In 14 sets of solar cells, standard deviations of 11 sets of solar cells were less than 0.50% and the smallest standard deviation was 0.25%, which demonstrates the reliability and effectiveness of hybrid physical chemical vapor deposition (HPCVD) method.

  17. Polarization-independent terahertz wave modulator based on graphene-silicon hybrid structure

    Science.gov (United States)

    Liang-Liang, Du; Quan, Li; Shao-Xian, Li; Fang-Rong, Hu; Xian-Ming, Xiong; Yan-Feng, Li; Wen-Tao, Zhang; Jia-Guang, Han

    2016-02-01

    In this study, we propose and demonstrate a broadband polarization-independent terahertz modulator based on graphene/silicon hybrid structure through a combination of continuous wave optical illumination and electrical gating. Under a pump power of 400 mW and the voltages ranging from -1.8 V to 1.4 V, modulation depths in a range of -23%-62% are achieved in a frequency range from 0.25 THz to 0.65 THz. The modulator is also found to have a transition from unidirectional modulation to bidirectional modulation with the increase of pump power. Combining the Raman spectra and Schottky current-voltage characteristics of the device, it is found that the large amplitude modulation is ascribed to the electric-field controlled carrier concentration in silicon with assistance of the graphene electrode and Schottky junction. Project supported by the National Natural Science Foundation of China (Grant No. 61565004), the Natural Science Foundation of Guangxi Zhuang Autonomous Region, China (Grant Nos. 2013GXNSFDA019002 and 2014GXNSFGA118003), the Guangxi Scientific Research and Technology Development Program, China (Grant No. 1598017-1), the Guilin Scientific Research and Technology Development Program, China (Grant Nos. 20140127-1 and 20150133-3), and the Special Funds for Distinguished Experts of Guangxi Zhuang Autonomous Region, China.

  18. Influence of structural fluctuations on lifetimes of adsorbate states at hybrid organic-semiconductor interfaces

    Science.gov (United States)

    Müller, M.; Sánchez-Portal, D.; Lin, H.; Fratesi, G.; Brivio, G. P.; Selloni, A.

    On the road towards a more realistic description of charge transfer processes at hybrid organic-semiconductor interfaces for photovoltaic applications we extend our first-principles scheme for the extraction of elastic linewidths to include the effects of structural fluctuations. Based on snapshots obtained from Car-Parinello molecular dynamics simulations at room temperature, we set up geometries in which dye molecules at interfaces are attached to a semi-infinite TiO2 substrate. The elastic linewidths are computed using a Green's function method. This effectively introduces the coupling to a continuum of states in the substrate. In particular we investigate catechol and isonicotinic acid on rutile(110) and anatase(101) at the level of semi-local density functional theory. We perform multiple calculations of linewidths and peak-positions associated with the adsorbate's frontier orbitals for different geometric configurations to obtain a time-averaged analysis of such physical properties. We compare the results from the considered systems to understand the effects of dynamics onto interfacial charge transfer and systematically assess the dependence of the extracted elastic lifetimes on the relative alignment between adsorbate and substrate states. This project has received funding from the European Union Seventh Framework Programme under Grant Agreement No. 607323 [THINFACE].

  19. AFM study of excimer laser patterning of block-copolymer: Creation of ordered hierarchical, hybrid, or recessed structures

    International Nuclear Information System (INIS)

    Švanda, Jan; Siegel, Jakub; Švorčík, Vaclav; Lyutakov, Oleksiy

    2016-01-01

    Highlights: • Combination of bottom-up (BCP separation) and top-down (laser patterning) technologies allows obtaining hierarchical structures. • Surface morphologies were determined by the order of patterning steps (laser modification, annealing, surface reconstruction). • Tuning the order of steps enables the reorientation of BCP domain at large scale, fabrication of hierarchical, hybrid or recessed structures. • The obtained structures can find potential applications in nanotechnology, plasmonics, information storage, sensors and smart surfaces. - Abstract: We report fabrication of the varied range of hierarchical structures by combining bottom-up self-assembly of block copolymer poly(styrene-block-vinylpyridine) (PS-b-P4VP) with top-down excimer laser patterning method. Different procedures were tested, where laser treatment was applied before phase separation and after phase separation or phase separation and surface reconstruction. Laser treatment was performed using either polarized laser light with the aim to create periodical pattern on polymer surface or non-polarized light for preferential removing of polystyrene (PS) part from PS-b-P4VP. Additionally, dye was introduced into one part of block copolymer (P4VP) with the aim to modify its response to laser light. Resulting structures were analyzed by XPS, UV–vis and AFM techniques. Application of polarized laser light leads to creation of structures with hierarchical, recessed or hybrid geometries. Non-polarized laser beam allows pronouncing the block copolymer phase separated structure. Tuning the order of steps or individual step conditions enables the efficient reorientation of block-copolymer domain at large scale, fabrication of hierarchical, hybrid or recessed structures. The obtained structures can find potential applications in nanotechnology, photonics, plasmonics, information storage, optical devices, sensors and smart surfaces.

  20. Projected Commutator DIIS Method for Accelerating Hybrid Functional Electronic Structure Calculations.

    Science.gov (United States)

    Hu, Wei; Lin, Lin; Yang, Chao

    2017-11-14

    The commutator direct inversion of the iterative subspace (commutator DIIS or C-DIIS) method developed by Pulay is an efficient and the most widely used scheme in quantum chemistry to accelerate the convergence of self-consistent field (SCF) iterations in Hartree-Fock theory and Kohn-Sham density functional theory. The C-DIIS method requires the explicit storage of the density matrix, the Fock matrix, and the commutator matrix. Hence, the method can only be used for systems with a relatively small basis set, such as the Gaussian basis set. We develop a new method that enables the C-DIIS method to be efficiently employed in electronic structure calculations with a large basis set such as planewaves for the first time. The key ingredient is the projection of both the density matrix and the commutator matrix to an auxiliary matrix called the gauge-fixing matrix. The resulting projected commutator-DIIS method (PC-DIIS) only operates on matrices of the same dimension as that consists of Kohn-Sham orbitals. The cost of the method is comparable to that of standard charge mixing schemes used in large basis set calculations. The PC-DIIS method is gauge-invariant, which guarantees that its performance is invariant with respect to any unitary transformation of the Kohn-Sham orbitals. We demonstrate that the PC-DIIS method can be viewed as an extension of an iterative eigensolver for nonlinear problems. We use the PC-DIIS method for accelerating Kohn-Sham density functional theory calculations with hybrid exchange-correlation functionals, and demonstrate its superior performance compared to the commonly used nested two-level SCF iteration procedure. Furthermore, we demonstrate that in the context of ab initio molecular dynamics (MD) simulation with hybrid functionals one can extrapolate the gauge-fixing matrix to achieve the goal of extrapolating the entire density matrix implicitly along the MD trajectory. Numerical results indicate that the new method significantly reduces

  1. Evaluating structural and microstructural changes of PDMS –SiO{sub 2} hybrid materials after sterilization by gamma irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, J. Carlos [Department of Materials and Ceramic Engineering/CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Lancastre, Joana [Campus Tecnologico e Nuclear, IST, University of Lisbon, E.N 10, 2686-953 Sacavém (Portugal); Vaz Fernandes, M. Helena [Department of Materials and Ceramic Engineering/CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Margaça, Fernanda M.A.; Ferreira, Luís [Campus Tecnologico e Nuclear, IST, University of Lisbon, E.N 10, 2686-953 Sacavém (Portugal); Miranda Salvado, Isabel M., E-mail: isabelmsalvado@ua.pt [Department of Materials and Ceramic Engineering/CICECO, University of Aveiro, 3810-193 Aveiro (Portugal)

    2015-03-01

    PDMS–SiO{sub 2} hybrid materials obtained by sol–gel process have been extensively studied over the past years due to its promising biomedical applications namely as bone substitutes, catheters, and drug delivery devices. Regardless of the intended biomedical application, all these materials should go through a sterilization process before interfacing with a living structure. However, it is unclear whether they undergo structural and microstructural changes when subjected to sterilization by gamma irradiation. This paper addresses this issue by showing that a sol–gel processed biomaterial based on the PDMS–CaO–SiO{sub 2} hybrid system suffers only small structural changes when submitted to a radiation dose of 25 kGy, the dose usually recommended to achieve a Sterility Assurance Level of 10{sup −6} when the natural contamination level and microorganism types cannot be calculated. The characterization was assessed by FT-IR, {sup 29}Si–{"1H} CP-MAS, thermal analysis (DTG), and SEM. - Highlights: • Hybrid PDMS–SiO{sub 2} materials were subjected to sterilization by γ-irradiation. • Materials suffer only small structural changes when irradiated. • Characterization was assessed by FT-IR, {sup 29}Si-{"1H} CP-MAS, DTG and SEM.

  2. Hybrid finite-element/rigorous coupled wave analysis for scattering from three-dimensional doubly periodic structures.

    Science.gov (United States)

    Kuloglu, Mustafa; Lee, Robert

    2012-07-01

    A new hybrid finite-element/rigorous coupled wave analysis formulation is presented for the modeling of electromagnetic wave interactions with doubly periodic structures. The structures under investigation are periodic in two dimensions and have a finite extent in the third dimension. The proposed model can handle structures that have material properties varying arbitrarily in any of the dimensions within the unit cell. Employment of Fourier series expansion and Floquet's theory in one of the periodic dimensions helps to reduce the dimension of the mesh. Results obtained from alternative methods are used to verify the proposed method's validity.

  3. Comparison of Welding Residual Stresses of Hybrid Laser-Arc Welding and Submerged Arc Welding in Offshore Steel Structures

    DEFF Research Database (Denmark)

    Andreassen, Michael Joachim; Yu, Zhenzhen; Liu, Stephen

    2016-01-01

    In the offshore industry, welding-induced distortion and tensile residual stresses have become a major concern in relation to the structural integrity of a welded structure. Particularly, the continuous increase in size of welded plates and joints needs special attention concerning welding induced...... are hybrid laser-arc welding (HLAW) and submerged arc welding (SAW). Both welding methods are applied for a full penetration butt-weld of 10 mm thick plates made of thermomechanically hot-rolled, low-carbon, fine-grain S355ML grade steel used in offshore steel structures. The welding residual stress state...

  4. AFM Imaging of Hybridization Chain Reaction-Mediated Signal Transmission Between two DNA Origami Structures

    DEFF Research Database (Denmark)

    Helmig, Sarah Wendelbo; Gothelf, Kurt Vesterager

    2017-01-01

    transfer between two connected DNA nanostructures, using the hybridization chain reaction (HCR). Two sets of metastable DNA hairpins - of which one is immobilized in specific points along tracks on DNA origami structures - are polymerized to form a continuous DNA duplex, which is visible using atomic force...... microscopy (AFM). Upon addition of a designed initiator, the initiation signal is efficiently transferred >200 nm from a specific location on one origami structure to an end point on another origami structure. The system shows no significant loss of signal when crossing from one nanostructure to another...

  5. Large Lateral Photovoltaic Effect in Metal-(Oxide-Semiconductor Structures

    Directory of Open Access Journals (Sweden)

    Chongqi Yu

    2010-11-01

    Full Text Available The lateral photovoltaic effect (LPE can be used in position-sensitive detectors to detect very small displacements due to its output of lateral photovoltage changing linearly with light spot position. In this review, we will summarize some of our recent works regarding LPE in metal-semiconductor and metal-oxide-semiconductor structures, and give a theoretical model of LPE in these two structures.

  6. Large lateral photovoltaic effect in metal-(oxide-) semiconductor structures.

    Science.gov (United States)

    Yu, Chongqi; Wang, Hui

    2010-01-01

    The lateral photovoltaic effect (LPE) can be used in position-sensitive detectors to detect very small displacements due to its output of lateral photovoltage changing linearly with light spot position. In this review, we will summarize some of our recent works regarding LPE in metal-semiconductor and metal-oxide-semiconductor structures, and give a theoretical model of LPE in these two structures.

  7. Single-fluorophore monitoring of DNA hybridization for investigating the effect of secondary structure on the nucleation step.

    Science.gov (United States)

    Jo, Joon-Jung; Kim, Min-Ji; Son, Jung-Tae; Kim, Jandi; Shin, Jong-Shik

    2009-07-17

    Nucleic acid hybridization is one of the essential biological processes involved in storage and transmission of genetic information. Here we quantitatively determined the effect of secondary structure on the hybridization activation energy using structurally defined oligonucleotides. It turned out that activation energy is linearly proportional to the length of a single-stranded region flanking a nucleation site, generating a 0.18 kcal/mol energy barrier per nucleotide. Based on this result, we propose that the presence of single-stranded segments available for non-productive base pairing with a nucleation counterpart extends the searching process for nucleation sites to find a perfect match. This result may provide insights into rational selection of a target mRNA site for siRNA and antisense gene silencing.

  8. Stereoselective green synthesis and molecular structures of highly functionalized spirooxindole-pyrrolidine hybrids - A combined experimental and theoretical investigation

    Science.gov (United States)

    Kumar, Raju Suresh; Almansour, Abdulrahman I.; Arumugam, Natarajan; Soliman, Saied M.; Kumar, Raju Ranjith; Altaf, Mohammad; Ghabbour, Hazem A.; Krishnamoorthy, Bellie Sundaram

    2018-01-01

    Highly functionalized spirooxindole-pyrrolidine hybrids have been synthesized stereoselectively through a [3 + 2] cycloaddition strategy in an ionic liquid, 1-butyl-3-methylimidazolium bromide ([bmim]Br). The structure of these spiro heterocyclic hybrids was elucidated using one and two dimensional NMR spectroscopy, single crystal X-ray crystallographic studies and Density Functional Theory (DFT) calculations. The calculated geometric parameters are in good agreement with the experimental data obtained from the X-ray structures. The Natural Bond Orbital (NBO) calculations on these molecules confirm the electron rich carbonyl oxygen and electron deficient NH groups. The 1H and 13C NMR chemical shifts calculated using GIAO method are in good agreement with the experimental data. The DFT computed polarizability values also suggest the possible NLO activity of these molecules.

  9. Structural Differences of the Harderian Gland between Common Pheasants (Phasianus Colchicus Talischensis and Hybrids of Italian Amber and Common Pheasants

    Directory of Open Access Journals (Sweden)

    J Klećkowska-Nawrot

    Full Text Available ABSTRACT The aim of the present study was to demonstrate the histological and histochemical structure of the Harderian gland in wild and hybrid of wild and domestic birds. The samples were stained with haematoxylin-eosin, methyl green-pyronin Y, periodic acid-Schiff, alcian blue pH 2.5, aldehyde fuchsin and Hale's dialyzed iron staining's. In both species, the glands had multilobar tubuloacinar structure type I. The Harderian gland was located in the orbit near the inter-orbital septum, between the medial rectus muscle, the pyramidal muscle of the third eyelid, and the ventral oblique muscle. In the common pheasant, the gland was wider in the proximal and distal part. The common pheasant had more elongated lobes of the Harderian gland than in the hybrid. In the common pheasant, the glandular cells presented darkly-stained serous secretion and lightly-stained mucous secretion. In the hybrid, the glandular cells presented seromucous secretion. The central lobar space, interacinar space, and apical parts of the acini of the Harderian glands were filled with many lymphocytes and plasma cells, particularly in the common pheasant, where centers of all large lobes were abundantly filled with plasma cells. The plasma cells dominated in common pheasant's Harderian gland, while in the hybrid, lymphocytes and plasma cells were present at similar quantities. The cells positive for periodic acid of Schiff staining were dominant in hybrid. Periodic acid-Schiff, Hale's dialyzed iron and alcian blue pH 2.5 stainings demonstrated acid-carboxylated mucopolysaccharides in the glandular cells cytoplasm of the examined birds.

  10. Enhancing prospective chemistry teachers cognitive structures in the topics of bonding and hybridization by internet-assisted chemistry applications

    OpenAIRE

    Özge Özyalçın Oskay, Sinem Dinçol

    2011-01-01

    The purpose of this study is to determine the effects of internet-assisted chemistry applications on prospective chemistry teachers’ cognitive structures in the topics of bonding and hybridization. The sample of the study consisted of 36 prospective chemistry teachers attending Hacettepe University, Faculty of Education, the Department of Chemistry Education in 2010-2011 academic year and taking Basic Chemistry I lesson. In the study, students were separated into experimental and control gr...

  11. Stationary transport in mesoscopic hybrid structures with contacts to superconducting and normal wires. A Green's function approach for multiterminal setups

    OpenAIRE

    Arrachea, Liliana

    2008-01-01

    We generalize the representation of the real time Green's functions introduced by Langreth and Nordlander [Phys. Rev. B 43 2541 (1991)] and Meir and Wingreen [Phys. Rev. Lett. 68 2512 (1992)] in stationary quantum transport in order to study problems with hybrid structures containing normal (N) and superconducting (S) pieces. We illustrate the treatment in a S-N junction under a stationary bias and investigate in detail the behavior of the equilibrium currents in a normal ring threaded by a m...

  12. Benefit Analysis of Hybrid CNT/CFRP Composites in Future Aircraft Structures, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — During Phase I, Aurora Flight Sciences and N12 Technologies propose to conduct a comprehensive analysis of the benefits of hybrid composites in future aircraft...

  13. Nano-Structured Bio-Inorganic Hybrid Material for High Performing Oxygen Reduction Catalyst.

    Science.gov (United States)

    Jiang, Rongzhong; Tran, Dat T; McClure, Joshua P; Chu, Deryn

    2015-08-26

    In this study, we demonstrate a non-Pt nanostructured bioinorganic hybrid (BIH) catalyst for catalytic oxygen reduction in alkaline media. This catalyst was synthesized through biomaterial hemin, nanostructured Ag-Co alloy, and graphene nano platelets (GNP) by heat-treatment and ultrasonically processing. This hybrid catalyst has the advantages of the combined features of these bio and inorganic materials. A 10-fold improvement in catalytic activity (at 0.8 V vs RHE) is achieved in comparison of pure Ag nanoparticles (20-40 nm). The hybrid catalyst reaches 80% activity (at 0.8 V vs RHE) of the state-of-the-art catalyst (containing 40% Pt and 60% active carbon). Comparable catalytic stability for the hybrid catalyst with the Pt catalyst is observed by chronoamperometric experiment. The hybrid catalyst catalyzes 4-electron oxygen reduction to produce water with fast kinetic rate. The rate constant obtained from the hybrid catalyst (at 0.6 V vs RHE) is 4 times higher than that of pure Ag/GNP catalyst. A catalytic model is proposed to explain the oxygen reduction reaction at the BIH catalyst.

  14. Nature of low dimensional structural modulations and relative phase stability in RexMo(W)1-xS2 transition metal dichalcogenide alloys

    KAUST Repository

    Sahu, R.

    2017-03-08

    We report on the various types of Peierls like two dimensional structural modulations and relative phase stability of 2H and 1T poly-types in the RexMo1-xS2 and RexW1-xS2 alloy system. Theoretical calculation predicts a polytype phase transition cross over at ∼50 at. % of Mo and W in ReS2 in both monolayer and bulk form, respectively. Experimentally, two different types of structural modulations at 50% and a modulation corresponding to trimerization at 75% alloy composition are observed for RexMo1-xS2 and only one type of modulation is observed at the 50% RexW1-xS2 alloy system. The 50% alloy system is found to be a suitable monolithic candidate for metal semiconductor transition with minute external perturbation. ReS2 is known to be in the 2D Peierls distorted 1Td structure and forms a chain like superstructure. Incorporation of Mo and W atoms into the ReS2 lattice modifies the metal-metal hybridization between the cations and influences the structural modulation and electronic properties of the system. The results offer yet another effective way to tune the electronic structure and poly-type phases of this class of materials other than intercalation, strain, and vertical stacking arrangement.

  15. In situ corrosion monitoring of PC structures with distributed hybrid carbon fiber reinforced polymer sensors

    Science.gov (United States)

    Yang, C. Q.; Wu, Z. S.

    2007-08-01

    Firstly, the fabrication and sensing properties of hybrid carbon fiber reinforced polymer (HCFRP) composite sensors are addressed. In order to provide a distributed sensing manner, the HCFRP sensors were divided into multi-zones with electrodes, and each zone was regarded as a separate sensor. Secondly, their application is studied to monitor the steel corrosion of prestressed concrete (PC) beams. The HCFRP sensors with different gauge lengths were mounted on a PC tendon, steel bar and embedded in tensile and compressive sides of the PC beam. The experiment was carried out under an electric accelerated corrosion and a constant load of about 54 kN. The results reveal that the corrosion of the PC tendon can be monitored through measuring the electrical resistance (ER) change of the HCFRP sensors. For the sensors embedded in tensile side of the PC beam, their ER increases as the corrosion progresses, whereas for the sensors embedded in compressive side, their ER decreases with corrosion time. Moreover, the strains due to the corrosion can be obtained based on the ER change and calibration curves of HCFRP sensors. The strains measured with traditional strain gauges agree with the strains calculated from the ER changes of HCFRP sensors. The electrical behavior of the zones where the corrosion was performed is much different from those of the other zones. In these zones, either there exist jumps in ER, or the ER increases with a much larger rate than those of the other zones. Distributed corrosion monitoring for PC structures is thus demonstrated with the application of HCFRP sensors through a proper installation of multi-electrodes.

  16. Mapping of coma anisotropies to plasma structures of weak comets: a 3-D hybrid simulation study

    Directory of Open Access Journals (Sweden)

    N. Gortsas

    2009-04-01

    Full Text Available The effects of coma anisotropies on the plasma environment of comets have been studied by means of a 3-D hybrid model which treats electrons as a massless, charge-neutralizing fluid, whereas ion dynamics are covered by a kinetic approach. From Earth-based observations as well as from in-situ spacecraft measurements the shape of the coma of many comets is ascertained to be anisotropic. However, most plasma simulation studies deploy a spherically symmetric activity pattern. In this paper anisotropy is studied by considering three different coma shape models. The first model is derived from the Haser model and is characterised by spherically symmetry. This reference model is then compared with two different neutral gas shape models: the dayside restricted model with no nightside activity and a cone shaped model with opening angle of π/2. In all models the integrated surface activity is kept constant. The simulations have been done for the Rosetta target comet 67P/Churyumov-Gerasimenko for two heliocentric distances, 1.30 AU and 3.25 AU. It is found that shock formation processes are modified as a result of increasing spatial confinement. Characteristic plasma structures of comets such as the bow shock, magnetic barrier region and the ion composition boundary exhibit a shift towards the sun. In addition, the cone shaped model leads to a strong increase of the mass-loaded region which in turn leads to a smooth deceleration of the solar wind flow and an increasing degree of mixture between the solar wind and cometary ion species. This creates an additional transport channel of the magnetic field from the magnetic barrier region away which in turn leads to a broadening of this region. In addition, it leads to an ion composition boundary which is only gradually developed.

  17. Hybrid molecule/superconductor assemblies

    International Nuclear Information System (INIS)

    McDevitt, J.T.; Haupt, S.G.; Riley, D.R.; Zhao, J.; Zhou, J.P., Jones, C.

    1993-01-01

    The fabrication of electronic devices from molecular materials has attracted much attention recently. Schottky diodes, molecular transistors, metal-insulator-semiconductor diodes, MIS field effect transistors and light emitting diodes have all been prepared utilizing such substances. The active elements in these devices have been constructed by depositing the molecular phase onto the surface of a metal, semiconductor or insulating substrate. With the recent discovery of high temperature superconductivity, new opportunities now exist for the study of molecule/superconductor interactions as well as for the construction of novel hybrid molecule/superconductor devices. In this paper, methods for preparing the initial two composite molecule/semiconductor devices will be reported. Consequently, light sensors based on dye-coated superconductor junctions as well as molecular switches fashioned from conductive polymer coated superconductor junctions as well as molecular switches fashioned from conductive polymer coated superconductor microbridges will be discussed. Moreover, molecule/superconductor energy and electron transfer phenomena will be illustrated also for the first time

  18. Limits of RNA 2'-OH Mimicry by Fluorine: Crystal Structure of Bacillus halodurans RNase H Bound to a 2'-FRNA:DNA Hybrid.

    Science.gov (United States)

    Pallan, Pradeep S; Prakash, Thazha P; de Leon, Arnie R; Egli, Martin

    2016-09-27

    RNase H1 cleaves the RNA strand of RNA:DNA hybrids. Replacement of RNA 2'-hydroxyls by fluorine (FRNA) is commonly used to stabilize aptamers and siRNAs. However, FRNA:DNA hybrids fail to elicit RNase H activity. The underlying reasons are unclear, as 2'-OH groups are not directly involved in cleavage. We determined the crystal structure of Bacillus halodurans RNase H bound to a FRNA:DNA hybrid. The structure points to dynamic (slippage of the FRNA:DNA hybrid relative to the enzyme), geometric (different curvatures of FRNA:DNA and RNA:DNA hybrids), and electronic reasons (Mg(2+) absent from the active site of the FRNA:DNA complex) for the loss of RNaseH activity.

  19. Nano-Sized Structurally Disordered Metal Oxide Composite Aerogels as High-Power Anodes in Hybrid Supercapacitors.

    Science.gov (United States)

    Huang, Haijian; Wang, Xing; Tervoort, Elena; Zeng, Guobo; Liu, Tian; Chen, Xi; Sologubenko, Alla; Niederberger, Markus

    2018-03-27

    A general method for preparing nano-sized metal oxide nanoparticles with highly disordered crystal structure and their processing into stable aqueous dispersions is presented. With these nanoparticles as building blocks, a series of nanoparticles@reduced graphene oxide (rGO) composite aerogels are fabricated and directly used as high-power anodes for lithium-ion hybrid supercapacitors (Li-HSCs). To clarify the effect of the degree of disorder, control samples of crystalline nanoparticles with similar particle size are prepared. The results indicate that the structurally disordered samples show a significantly enhanced electrochemical performance compared to the crystalline counterparts. In particular, structurally disordered Ni x Fe y O z @rGO delivers a capacity of 388 mAh g -1 at 5 A g -1 , which is 6 times that of the crystalline sample. Disordered Ni x Fe y O z @rGO is taken as an example to study the reasons for the enhanced performance. Compared with the crystalline sample, density functional theory calculations reveal a smaller volume expansion during Li + insertion for the structurally disordered Ni x Fe y O z nanoparticles, and they are found to exhibit larger pseudocapacitive effects. Combined with an activated carbon (AC) cathode, full-cell tests of the lithium-ion hybrid supercapacitors are performed, demonstrating that the structurally disordered metal oxide nanoparticles@rGO||AC hybrid systems deliver high energy and power densities within the voltage range of 1.0-4.0 V. These results indicate that structurally disordered nanomaterials might be interesting candidates for exploring high-power anodes for Li-HSCs.

  20. A protected area influences genotype-specific survival and the structure of a Canis hybrid zone.

    Science.gov (United States)

    Benson, John F; Patterson, Brent R; Mahoney, Peter J

    2014-02-01

    It is widely recognized that protected areas can strongly influence ecological systems and that hybridization is an important conservation issue. However, previous studies have not explicitly considered the influence of protected areas on hybridization dynamics. Eastern wolves are a species of special concern and their distribution is largely restricted to a protected population in Algonquin Provincial Park (APP), Ontario, Canada, where they are the numerically dominant canid. We studied intrinsic and extrinsic factors influencing survival and cause-specific mortality of hybrid and parental canids in the three-species hybrid zone between eastern wolves, eastern coyotes, and gray wolves in and adjacent to APP. Mortality risk for eastern wolves in areas adjacent to APP was significantly higher than for other sympatric Canis types outside of APP, and for eastern wolves and other canids within APP. Outside of APP, the annual mortality rate of all canids by harvest (24%) was higher than for other causes of death (4-7%). Furthermore, eastern wolves (hazard ratio = 3.5) and nonresidents (transients and dispersing animals, hazard ratio = 2.7) were more likely to die from harvest relative to other Canis types and residents, respectively. Thus, eastern wolves dispersing from APP were especially vulnerable to harvest mortality. For residents, eastern wolf survival was more negatively influenced by increased road density than for other Canis types, further highlighting the sensitivity of eastern wolves to human disturbance. A cycle of dispersal from APP followed by high rates of mortality and hybridization appears to maintain eastern wolves at low density adjacent to APP, limiting the potential for expansion beyond the protected area. However, high survival and numerical dominance of eastern wolves within APP suggest that protected areas can allow rare hybridizing species to persist even if their demographic performance is compromised and barriers to hybridization are largely

  1. From (Cd2Se2)(pa) (pa=propylamine) hybrid precursors to various CdSe nanostructures: structural evolution and optical properties.

    Science.gov (United States)

    Yao, Hong-Bin; Zhang, Xiao; Wang, Xiao-Han; Yu, Shu-Hong; Li, Jing

    2011-04-07

    Nanostructural evolution of II-VI semiconductors emerges as a hot research field because it offers a novel route for the synthesis of functional semiconductor nanomaterials. Here, we report a "top-down" process of structural evolution from two dimensional Cd(2)Se(2)(pa) hybrid structures to zero- or one- dimensional CdSe nanostructures. We firstly synthesized the Cd(2)Se(2)(pa) hybrid by a facile solvothermal reaction and determined the hybrid crystal structure through the Rietveld refinement based on the PXRD data. The (Cd(2)Se(2))(pa) hybrid consists of [Cd(2)Se(2)] slabs sandwiched by coordinated n-propylamine layers. Then, we used this hybrid as a precursor to explore the "top-down" fabrication process of structural evolution from two dimensional layered structures to zero- or one- dimensional nanocrystals. It has been shown that various CdSe nanostructures including lamellar structures, nanoparticles, nanowires, and nanorods can be obtained through the pyrolysis of (Cd(2)Se(2))(pa) hybrid precursor under different conditions. It is worth mentioning that the oriented attachment of nanoparticles has been observed during the pyrolysis process. Additionally, the variation of optical properties with structural evolution has been investigated in detail. © The Royal Society of Chemistry 2011

  2. POPULATION STRUCTURE AND HOST USE IN HYBRIDIZING SUBSPECIES OF PAPILIO GLAUCUS (LEPIDOPTERA: PAPILIONIDAE).

    Science.gov (United States)

    Hagen, Robert H

    1990-12-01

    Two parapatric subspecies of the eastern tiger swallowtail butterfly, Papilio glaucus glaucus and P. g. canadensis, differ greatly in larval survival and growth on host plants in the Magnoliaceae, Salicaceae, and Betulaceae. In the first part of this study, butterflies were collected from 17 sites along a transect from Georgia to Quebec and used for allozyme electrophoresis. Two X- (or Z-)linked enzyme loci (Ldh and Pgd) showed allele frequency differences that delineated a hybrid zone between the subspecies in northern Pennsylvania and south-central New York. No significant linkage disequilibrium could be detected among allozyme loci within the hybrid zone samples. Genetic differentiation at Ldh and Pgd coincides with subspecies differences in diapause control and female mimicry, which are also sex-linked. Larval offspring of butterflies from 13 of the sites were then tested in the laboratory for survival and growth on Liriodendron tulipifera (Magnoliaceae), Populus deltoïdes (Salicaceae) and Betula lutea (Betulaceae). Steep clines in survival rates matched the position of the hybrid zone. Hybrid zone larvae showed intermediate survival rates and significant heterogeneity among families on all three plants, indicating presence of substantial genetic variation. The results suggest that differential host use by P. g. glaucus and P. g. canadensis is maintained primarily by independent clines in selection intensity for ability to use allopatric sets of host plants, coupled with restricted gene flow across the hybrid zone. © 1990 The Society for the Study of Evolution.

  3. Metal Decoration Effects on the Gas-Sensing Properties of 2D Hybrid-Structures on Flexible Substrates

    Directory of Open Access Journals (Sweden)

    Byungjin Cho

    2015-09-01

    Full Text Available We have investigated the effects of metal decoration on the gas-sensing properties of a device with two-dimensional (2D molybdenum disulfide (MoS2 flake channels and graphene electrodes. The 2D hybrid-structure device sensitively detected NO2 gas molecules (>1.2 ppm as well as NH3 (>10 ppm. Metal nanoparticles (NPs could tune the electronic properties of the 2D graphene/MoS2 device, increasing sensitivity to a specific gas molecule. For instance, palladium NPs accumulate hole carriers of graphene/MoS2, electronically sensitizing NH3 gas molecules. Contrarily, aluminum NPs deplete hole carriers, enhancing NO2 sensitivity. The synergistic combination of metal NPs and 2D hybrid layers could be also applied to a flexible gas sensor. There was no serious degradation in the sensing performance of metal-decorated MoS2 flexible devices before/after 5000 bending cycles. Thus, highly sensitive and endurable gas sensor could be achieved through the metal-decorated 2D hybrid-structure, offering a useful route to wearable electronic sensing platforms.

  4. Metal Decoration Effects on the Gas-Sensing Properties of 2D Hybrid-Structures on Flexible Substrates.

    Science.gov (United States)

    Cho, Byungjin; Yoon, Jongwon; Lim, Sung Kwan; Kim, Ah Ra; Choi, Sun-Young; Kim, Dong-Ho; Lee, Kyu Hwan; Lee, Byoung Hun; Ko, Heung Cho; Hahm, Myung Gwan

    2015-09-25

    We have investigated the effects of metal decoration on the gas-sensing properties of a device with two-dimensional (2D) molybdenum disulfide (MoS₂) flake channels and graphene electrodes. The 2D hybrid-structure device sensitively detected NO₂ gas molecules (>1.2 ppm) as well as NH₃ (>10 ppm). Metal nanoparticles (NPs) could tune the electronic properties of the 2D graphene/MoS₂ device, increasing sensitivity to a specific gas molecule. For instance, palladium NPs accumulate hole carriers of graphene/MoS₂, electronically sensitizing NH₃ gas molecules. Contrarily, aluminum NPs deplete hole carriers, enhancing NO₂ sensitivity. The synergistic combination of metal NPs and 2D hybrid layers could be also applied to a flexible gas sensor. There was no serious degradation in the sensing performance of metal-decorated MoS₂ flexible devices before/after 5000 bending cycles. Thus, highly sensitive and endurable gas sensor could be achieved through the metal-decorated 2D hybrid-structure, offering a useful route to wearable electronic sensing platforms.

  5. Synthesis and characterization of hybrid micro/nano-structured NiTi surfaces by a combination of etching and anodizing

    International Nuclear Information System (INIS)

    Huan, Z; Fratila-Apachitei, L E; Apachitei, I; Duszczyk, J

    2014-01-01

    The purpose of this study was to generate hybrid micro/nano-structures on biomedical nickel–titanium alloy (NiTi). To achieve this, NiTi surfaces were firstly electrochemically etched and then anodized in fluoride-containing electrolyte. With the etching process, the NiTi surface was micro-roughened through the formation of micropits uniformly distributed over the entire surface. Following the subsequent anodizing process, self-organized nanotube structures enriched in TiO 2 could be superimposed on the etched surface under specific conditions. Furthermore, the anodizing treatment significantly reduced water contact angles and increased the surface free energy compared to the surfaces prior to anodizing. The results of this study show for the first time that it is possible to create hybrid micro/nano-structures on biomedical NiTi alloys by combining electrochemical etching and anodizing under controlled conditions. These novel structures are expected to significantly enhance the surface biofunctionality of the material when compared to conventional implant devices with either micro- or nano-structured surfaces. (paper)

  6. Synthesis and characterization of hybrid micro/nano-structured NiTi surfaces by a combination of etching and anodizing.

    Science.gov (United States)

    Huan, Z; Fratila-Apachitei, L E; Apachitei, I; Duszczyk, J

    2014-02-07

    The purpose of this study was to generate hybrid micro/nano-structures on biomedical nickel-titanium alloy (NiTi). To achieve this, NiTi surfaces were firstly electrochemically etched and then anodized in fluoride-containing electrolyte. With the etching process, the NiTi surface was micro-roughened through the formation of micropits uniformly distributed over the entire surface. Following the subsequent anodizing process, self-organized nanotube structures enriched in TiO2 could be superimposed on the etched surface under specific conditions. Furthermore, the anodizing treatment significantly reduced water contact angles and increased the surface free energy compared to the surfaces prior to anodizing. The results of this study show for the first time that it is possible to create hybrid micro/nano-structures on biomedical NiTi alloys by combining electrochemical etching and anodizing under controlled conditions. These novel structures are expected to significantly enhance the surface biofunctionality of the material when compared to conventional implant devices with either micro- or nano-structured surfaces.

  7. Structural basis of the RNase H1 activity on stereo regular borano phosphonate DNA/RNA hybrids.

    Science.gov (United States)

    Johnson, Christopher N; Spring, Alexander M; Sergueev, Dimitri; Shaw, Barbara R; Germann, Markus W

    2011-05-17

    Numerous DNA chemistries for improving oligodeoxynucleotide (ODN)-based RNA targeting have been explored. The majority of the modifications render the ODN/RNA target insensitive to RNase H1. Borano phosphonate ODN's are among the few modifications that are tolerated by RNase H1. To understand the effect of the stereochemistry of the BH(3) modification on the nucleic acid structure and RNase H1 enzyme activity, we have investigated two DNA/RNA hybrids containing either a R(P) or S(P) BH(3) modification by nuclear magnetic resonance (NMR) spectroscopy. T(M) studies show that the stabilities of R(P) and S(P) modified DNA/RNA hybrids are essentially identical (313.8 K) and similar to that of an unmodified control (312.9 K). The similarity is also reflected in the imino proton spectra. To characterize such similar structures, we used a large number of NMR restraints (including dipolar couplings and backbone torsion angles) to determine structural features that were important for RNase H1 activity. The final NMR structures exhibit excellent agreement with the data (total R(x) values of DNA near the modification, while the RNA strands are relatively unperturbed. In the case of the S(P) modification, for which more perturbations are recorded, a slightly narrower minor groove is also obtained. Unique NOE base contacts localize the S(P) BH(3) group in the major groove while the R(P) BH(3) group points away from the DNA. However, this creates a potential clash of the R(P) BH(3) groups with important RNase H1 residues in a complex, while the S(P) BH(3) groups could be tolerated. We therefore predict that on the basis of our NMR structures a fully R(P) BH(3) DNA/RNA hybrid would not be a substrate for RNase H1.

  8. Enhancing prospective chemistry teachers cognitive structures in the topics of bonding and hybridization by internet-assisted chemistry applications

    Directory of Open Access Journals (Sweden)

    Özge Özyalçın Oskay, Sinem Dinçol

    2011-08-01

    Full Text Available The purpose of this study is to determine the effects of internet-assisted chemistry applications on prospective chemistry teachers’ cognitive structures in the topics of bonding and hybridization. The sample of the study consisted of 36 prospective chemistry teachers attending Hacettepe University, Faculty of Education, the Department of Chemistry Education in 2010-2011 academic year and taking Basic Chemistry I lesson. In the study, students were separated into experimental and control groups according to their pre-cognitive structures. Students were requested to answer two open ended questions. Answers by each student were gathered and evaluated by flow map method. “Bonding and hybridization” topics were taught to control group with traditional teaching method and to experimental group besides traditional method internet-assisted applications were conducted. The same open-ended questions were given to both groups and their cognitive structures were examined once more. The differences between control and experimental groups’ cognitive structures were examined. A significant difference was identified in favour of experimental group (p<0, 05. The mean score of the Experimental group was X=19.94, and the mean score of the Control group was X=13.88. In addition, subsequent to internet assisted chemistry applications differences in terms of concepts and descriptions in prospective chemistry teachers’ in experimental and control group cognitive structure have been determined. When post flow maps of prospective chemistry teachers in experimental group, on whom internet assisted chemistry applications were made, are formed, it has been determined that there are more statements about hybridization, hybridization types, molecule geometry and bond angles compared to control grou

  9. Analysis of a hybrid balanced laminate as a structural material for thick composite beams with axial stiffeners

    Energy Technology Data Exchange (ETDEWEB)

    Modak, Partha; Hossain, M. Jamil, E-mail: jamil917@gmail.com; Ahmed, S. Reaz [Department of Mechanical Engineering, Bangladesh University of Engineering and Technology, Dhaka 1000 (Bangladesh)

    2016-07-12

    An accurate stress analysis has been carried out to investigate the suitability of a hybrid balanced laminate as a structural material for thick composite beams with axial stiffeners. Three different balanced laminates composed of dissimilar ply material as well as fiber orientations are considered for a thick beam on simple supports with stiffened lateral ends. A displacement potential based elasticity approach is used to obtain the numerical solution of the corresponding elastic fields. The overall laminate stresses as well as individual ply stresses are analysed mainly in the perspective of laminate hybridization. Both the fiber material and ply angle of individual laminas are found to play dominant roles in defining the design stresses of the present composite beam.

  10. Exchange interaction of electrons with Mn in hybrid AlSb/InAs/ZnMnTe structures

    Energy Technology Data Exchange (ETDEWEB)

    Olbrich, P.; Zoth, C.; Drexler, C.; Lechner, V.; Lutz, P.; Ganichev, S.D. [University of Regensburg (Germany); Terent' ev, Ya.V.; Bel' kov, V.V.; Mukhin, M.S.; Tarasenko, S.A.; Semenov, A.N.; Solov' ev, V.A.; Klimko, G.V.; Komissarova, T.A.; Ivanov, S.V. [Ioffe Institute, St. Petersburg (Russian Federation)

    2012-07-01

    Here we report on the fabrication and investigation of Manganese modulation doped structures with an InAs two-dimensional electron gas (2DEG) channel. The quantum wells were grown applying III-V/II-VI ''hybrid'' technique and Mn layers have been inserted into the II-VI barrier. To explore the magnetic properties of the 2DEG we investigated spin polarized electric currents induced by microwave (mw) and terahertz (THz) radiation. Our measurements show that hybrid AlSb/InAs/(Zn,Mn)Te QWs are characterized by enhanced magnetic properties which can be changed by tuning of the spatial position of the Mn-doping layer as well as by the variation of temperature. We demonstrate that the exchange interaction is due to penetration of the electronic wave function into the (Zn,Mn)Te layer and can be controllably varied by the position and density of Mn{sup 2+} ions.

  11. Synthesis and Characterization of Silsesquioxane-Based Polymer Hybrids with Controlled Structure

    Directory of Open Access Journals (Sweden)

    Costa Ricardo O.R.

    2002-01-01

    Full Text Available We have developed a method to obtain polymer hybrids with control of inorganic content and molecular configuration. Hybrid poly(methyl methacrylate (PMMA was obtained via atom transfer radical polymerization (ATRP initiated by octafunctional cubic silsesquioxanes using CuCl as catalyst. Two different ATRP initiators obtained by attaching specific chemical groups to the cubic silsesquioxane were employed to produce two types of hybrids with different architectures. While a-bromide ester groups generated a star-shaped polymer, the benzyl chloride groups produced longer and more linear polymeric chains containing the cubic silsesquioxane. These results were explained on the basis of the low initiation efficiency of benzyl chloride groups for PMMA, leading to polymers with molecular weights (Mn and polydispersities (PDI higher than the expected ones.

  12. Carbon nanotube-nanocup hybrid structures for high power supercapacitor applications.

    Science.gov (United States)

    Hahm, Myung Gwan; Leela Mohana Reddy, Arava; Cole, Daniel P; Rivera, Monica; Vento, Joseph A; Nam, Jaewook; Jung, Hyun Young; Kim, Young Lae; Narayanan, Narayanan T; Hashim, Daniel P; Galande, Charudatta; Jung, Yung Joon; Bundy, Mark; Karna, Shashi; Ajayan, Pulickel M; Vajtai, Robert

    2012-11-14

    Here, we design and develop high-power electric double-layer capacitors (EDLCs) using carbon-based three dimensional (3-D) hybrid nanostructured electrodes. 3-D hybrid nanostructured electrodes consisting of vertically aligned carbon nanotubes (CNTs) on highly porous carbon nanocups (CNCs) were synthesized by a combination of anodization and chemical vapor deposition techniques. A 3-D electrode-based supercapacitor showed enhanced areal capacitance by accommodating more charges in a given footprint area than that of a conventional CNC-based device.

  13. Light-based theranostics using hybrid structures derived from biological and organic materials

    Science.gov (United States)

    Vankayala, Raviraj; Burns, Joshua M.; Mac, Jenny T.; Anvari, Bahman

    2016-09-01

    We have engineered hybrid nanostructures derived from erythrocytes, which can be doped with various near infrared (NIR) organic chromophores, including the FDA-approved indocyanine green (ICG). We refer to these vesicles as NIR erythrocyte-mimicking transducers (NETs), as they are capable of generating heat, reactive oxygen species (ROS) or emit fluorescence light. We present preliminary results that demonstrate the effectiveness of NETs for fluorescence imaging and photodynamic therapeutic destruction of breast cancer cells, upon photo-excitation using NIR light. These hybrid nanostructures present a promising platform with theranostic capability for future biomedical clinical applications.

  14. Angular Structure of Jet Quenching Within a Hybrid Strong/Weak Coupling Model

    CERN Document Server

    Casalderrey-Solana, Jorge; Milhano, Guilherme; Pablos, Daniel; Rajagopal, Krishna

    2017-01-01

    Within the context of a hybrid strong/weak coupling model of jet quenching, we study the modification of the angular distribution of the energy within jets in heavy ion collisions, as partons within jet showers lose energy and get kicked as they traverse the strongly coupled plasma produced in the collision. To describe the dynamics transverse to the jet axis, we add the effects of transverse momentum broadening into our hybrid construction, introducing a parameter $K\\equiv \\hat q/T^3$ that governs its magnitude. We show that, because of the quenching of the energy of partons within a jet, even when $K\

  15. Fabrication and study of hybrid molecule/superconductor assemblies

    International Nuclear Information System (INIS)

    McDevitt, J.T.; Haupt, S.G.; Jurbergs, D.; Riley, D.R.; Zhao, J.; Zhou, J.P.; Lo, K.; Grassi, J.; Jones, C.

    1994-01-01

    The fabrication of electronic devices from molecular materials has attracted much attention recently. Schottky diodes, molecular transistors, metal-insulator-semiconductor diodes, MIS field effect transistors and light emitting diodes have all been prepared utilizing such substances. The active elements in these devices have been constructed by depositing the molecular phase onto the surface of a metal, semiconductor or insulating substrate. With the recent discovery of high temperature superconductivity, new opportunities now exist for the study of molecule/superconductor interactions as well as for the construction of novel hybrid molecule/superconductor devices. In this paper, methods for preparing the first two classes of composite molecule/superconductor devices are reported. Consequently, light sensors based on organic dye-coated superconductor junctions as well as molecular switches fashioned from organic conductive polymer-coated superconductor microbridges are discussed. Moreover, the initial results related to the study of molecule/superconductor energy and electron transfer phenomena are reported

  16. An Experimental Study on Hybrid Noncompression CF Bracing and GF Sheet Wrapping Reinforcement Method to Restore Damaged RC Structures

    Directory of Open Access Journals (Sweden)

    Kang Seok Lee

    2015-01-01

    Full Text Available We describe a novel technique for restoration of reinforced concrete (RC structures that have sustained damage during an earthquake. The reinforcement scheme described here is a hybrid seismic retrofitting technique that combines noncompression X-bracing using CF with externally bonded GF sheets to strengthen RC structures that have sustained damage following an earthquake. The GF sheet is used to improve the ductility of columns, and the noncompression CF X-bracing system, which consists of CF bracing and anchors to replace the conventional steel bracing and bolt connections, is used to increase the lateral strength of the framing system. We report seismic restoration capacity, which enables reuse of the damaged RC frames via the hybrid CF X-bracing and GF sheet wrapping system. Cyclic loading tests were carried out to investigate hysteresis of the lateral load-drift relations, as well as the ductility. The GF sheet significantly improved the ductility of columns, resulting in a change in failure mode. The strengthening effect of conventional CF sheets used in columns is not sufficient with respect to lateral strength and stiffness. However, this study results in a significant increase in the strength of the structure due to the use of CF X-bracing and inhibited buckling failure of the bracing. This result can be exploited to develop guidelines for the application of the reinforcement system to restore damaged RC structures.

  17. Investigations of Crossed Andreev Reflection in Hybrid Superconductor-Ferromagnet Structures

    Science.gov (United States)

    Colci O'Hara, Madalina

    2009-01-01

    Cooper pair splitting is predicted to occur in hybrid devices where a superconductor is coupled to two ferromagnetic wires placed at a distance less than the superconducting coherence length. This thesis searches for signatures of this process, called crossed Andreev reflection (CAR), in three device geometries. The first devices studied are…

  18. History rather than hybridization determines population structure and adaptation in Populus balsamifera

    NARCIS (Netherlands)

    Meirmans, P.G.; Godbout, J.; Lamothe, M.; Thompson, S.L.; Isabel, N.

    2017-01-01

    Hybridization between species is known to greatly affect their genetic diversity and, therefore, their evolution. Also, within species, there may be genetic clusters between which gene flow is limited, which may impact natural selection. However, few studies have looked simultaneously at the

  19. Rare hybrid swarm of Pilosella polymastix × P. officinarum: cytotype structure and modes of reproduction

    Czech Academy of Sciences Publication Activity Database

    Krahulec, František; Krahulcová, Anna; Hlaváček, R.

    2014-01-01

    Roč. 86, č. 2 (2014), s. 179-192 ISSN 0032-7786 R&D Projects: GA ČR GAP506/10/1363; GA ČR GA206/08/0890 Institutional support: RVO:67985939 Keywords : chromosome numbers * hybrid swarm composition * reproductive models Subject RIV: EF - Botanics Impact factor: 4.104, year: 2014

  20. Analysis of hybrid dielectric-plasmonic slot waveguide structures with 3D Fourier modal methods

    Czech Academy of Sciences Publication Activity Database

    Čtyroký, Jiří; Kwiecien, P.; Richter, I.

    2013-01-01

    Roč. 8, 23 March (2013), s. 130241-130246 ISSN 1990-2573 R&D Projects: GA ČR(CZ) GAP205/10/0046; GA MŠk OC09061 Institutional support: RVO:67985882 Keywords : Fourier modal method * Hybrid dielectric-plasmonic waveguide * Plasmonic waveguides Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.152, year: 2013

  1. Transmission electron microscopy of unstained hybrid Au nanoparticles capped with PPAA (plasma-poly-allylamine): structure and electron irradiation effects.

    Science.gov (United States)

    Gontard, Lionel C; Fernández, Asunción; Dunin-Borkowski, Rafal E; Kasama, Takeshi; Lozano-Pérez, Sergio; Lucas, Stéphane

    2014-12-01

    Hybrid (organic shell-inorganic core) nanoparticles have important applications in nanomedicine. Although the inorganic components of hybrid nanoparticles can be characterized readily using conventional transmission electron microscopy (TEM) techniques, the structural and chemical arrangement of the organic molecular components remains largely unknown. Here, we apply TEM to the physico-chemical characterization of Au nanoparticles that are coated with plasma-polymerized-allylamine, an organic compound with the formula C3H5NH2. We discuss the use of energy-filtered TEM in the low-energy-loss range as a contrast enhancement mechanism for imaging the organic shells of such particles. We also study electron-beam-induced crystallization and amorphization of the shells and the formation of graphitic-like layers that contain both C and N. The resistance of the samples to irradiation by high-energy electrons, which is relevant for optical tuning and for understanding the degree to which such hybrid nanostructures are stable in the presence of biomedical radiation, is also discussed. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. AFM Imaging of Hybridization Chain Reaction-Mediated Signal Transmission Between two DNA Origami Structures

    DEFF Research Database (Denmark)

    Helmig, Sarah Wendelbo; Gothelf, Kurt Vesterager

    2017-01-01

    Signal transfer is central to the controlled exchange of information in biology and advanced technologies. Therefore, the development of reliable, long-ranging signal transfer systems for artificial nanoscale assemblies is of great scientific interest. We have designed such a system for signal...... transfer between two connected DNA nanostructures, using the hybridization chain reaction (HCR). Two sets of metastable DNA hairpins - of which one is immobilized in specific points along tracks on DNA origami structures - are polymerized to form a continuous DNA duplex, which is visible using atomic force......, and therefore has the potential to be applied to larger multi-component DNA assemblies...

  3. Photon-Storage in Optical Memory Cells Based on a Semiconductor Quantum Dot-Quantum Well Hybrid Structure

    Science.gov (United States)

    Bian, Song-Bao; Tang, Yan; Li, Gui-Rong; Li, Yue-Xia; Yang, Fu-Hua; Zheng, Hou-Zhi; Zeng, Yi-Ping

    2003-08-01

    We report a new type of photonic memory cell based on a semiconductor quantum dot (QD)-quantum well (QW) hybrid structure, in which photo-generated excitons can be decomposed into separated electrons and holes, and stored in QW and QDs respectively. Storage and retrieval of photonic signals are verified by time-resolved photoluminescence experiments. A storage time in excess of 100 ms has been obtained at a temperature of 10 K while the switching speed reaches the order of ten megahertz.

  4. A Hybrid Finite Element-Fourier Spectral Method for Vibration Analysis of Structures with Elastic Boundary Conditions

    Directory of Open Access Journals (Sweden)

    Wan-You Li

    2014-01-01

    Full Text Available A novel hybrid method, which simultaneously possesses the efficiency of Fourier spectral method (FSM and the applicability of the finite element method (FEM, is presented for the vibration analysis of structures with elastic boundary conditions. The FSM, as one type of analytical approaches with excellent convergence and accuracy, is mainly limited to problems with relatively regular geometry. The purpose of the current study is to extend the FSM to problems with irregular geometry via the FEM and attempt to take full advantage of the FSM and the conventional FEM for structural vibration problems. The computational domain of general shape is divided into several subdomains firstly, some of which are represented by the FSM while the rest by the FEM. Then, fictitious springs are introduced for connecting these subdomains. Sufficient details are given to describe the development of such a hybrid method. Numerical examples of a one-dimensional Euler-Bernoulli beam and a two-dimensional rectangular plate show that the present method has good accuracy and efficiency. Further, one irregular-shaped plate which consists of one rectangular plate and one semi-circular plate also demonstrates the capability of the present method applied to irregular structures.

  5. Optimal sensor placement for large structures using the nearest neighbour index and a hybrid swarm intelligence algorithm

    International Nuclear Information System (INIS)

    Lian, Jijian; He, Longjun; Ma, Bin; Peng, Wenxiang; Li, Huokun

    2013-01-01

    Research on optimal sensor placement (OSP) has become very important due to the need to obtain effective testing results with limited testing resources in health monitoring. In this study, a new methodology is proposed to select the best sensor locations for large structures. First, a novel fitness function derived from the nearest neighbour index is proposed to overcome the drawbacks of the effective independence method for OSP for large structures. This method maximizes the contribution of each sensor to modal observability and simultaneously avoids the redundancy of information between the selected degrees of freedom. A hybrid algorithm combining the improved discrete particle swarm optimization (DPSO) with the clonal selection algorithm is then implemented to optimize the proposed fitness function effectively. Finally, the proposed method is applied to an arch dam for performance verification. The results show that the proposed hybrid swarm intelligence algorithm outperforms a genetic algorithm with decimal two-dimension array encoding and DPSO in the capability of global optimization. The new fitness function is advantageous in terms of sensor distribution and ensuring a well-conditioned information matrix and orthogonality of modes, indicating that this method may be used to provide guidance for OSP in various large structures. (paper)

  6. Development of Pd Alloy Hydrogen Separation Membranes with Dense/Porous Hybrid Structure for High Hydrogen Perm-Selectivity

    Directory of Open Access Journals (Sweden)

    Jae-Yun Han

    2014-01-01

    Full Text Available For the commercial applications of hydrogen separation membranes, both high hydrogen selectivity and permeability (i.e., perm-selectivity are required. However, it has been difficult to fabricate thin, dense Pd alloy composite membranes on porous metal support that have a pore-free surface and an open structure at the interface between the Pd alloy films and the metal support in order to obtain the required properties simultaneously. In this study, we fabricated Pd alloy hydrogen separation membranes with dense/porous hybrid structure for high hydrogen perm-selectivity. The hydrogen selectivity of this membrane increased owing to the dense and pore-free microstructure of the membrane surface. The hydrogen permeation flux also was remarkably improved by the formation of an open microstructure with numerous open voids at the interface and by an effective reduction in the membrane thickness as a result of the porous structure formed within the Pd alloy films.

  7. A Hierarchical Phosphorus Nanobarbed Nanowire Hybrid: Its Structure and Electrochemical Properties.

    Science.gov (United States)

    Zhao, Dan; Li, Beibei; Zhang, Jinying; Li, Xin; Xiao, Dingbin; Fu, Chengcheng; Zhang, Lihui; Li, Zhihui; Li, Jun; Cao, Daxian; Niu, Chunming

    2017-06-14

    Nanostructured phosphorus-carbon composites are promising materials for Li-ion and Na-ion battery anodes. A hierarchical phosphorus hybrid, SiC@graphene@P, has been synthesized by the chemical vapor deposition of phosphorus on the surfaces of barbed nanowires, where the barbs are vertically grown graphene nanosheets and the cores are SiC nanowires. A temperature-gradient vaporization-condensation method has been used to remove the unhybridized phosphorus particles formed by homogeneous nucleation. The vertically grown barb shaped graphene nanosheets and a high concentration of edge carbon atoms induced a fibrous red phosphorus (f-RP) growth with its {001} planes in parallel to {002} planes of nanographene sheets and led to a strong interpenetrated interface interaction between phosphorus and the surfaces of graphene nanosheets. This hybridization has been demonstrated to significantly enhance the electrochemical performances of phosphorus.

  8. Structure and properties of hybrid poly(2-hydroxyethyl methacrylate)/SiO2 monoliths

    DEFF Research Database (Denmark)

    Ji, Xiangling; Jiang, Shichun; Qiu, Xuepeng

    2003-01-01

    Abstract: Hybrid poly(2-hydroxyethyl methacrylate) (PHEMA)/SiO2 monoliths were synthesized via a sol-gel process of the precursor tetraethyl orthosilicate (TEOS) and the in situ free-radical polymerization of 2-hydroxyethyl methacrylate (HEMA). The weight ratio of the starting chemicals, TEOS to ...... related to some degree of chemical crosslinking between the polymer and the silica moiety, which would greatly improve the thermal stability of such hybrid monoliths compared with a pure PHEMA....... region, that is, good transparency. Mechanical properties were studied with an Instron tester, and the monoliths exhibited better compressive strength and modulus than did bulk PHEMA. Surprisingly, thermogravimetric analysis (TGA) data showed greater than 50 wt % solid residue up to 700degreesC, possibly...

  9. Dynamic behavior of the mechanical systems from the structure of a hybrid automobile

    Science.gov (United States)

    Dinel, Popa; Irina, Tudor; Nicolae-Doru, Stănescu

    2017-10-01

    In introduction are presented solutions of planetary mechanisms that can be used in the construction of the hybrid automobiles where the thermal and electrical sources must be coupled. The systems have in their composition a planetary mechanism with two degrees of mobility at which are coupled a thermal engine, two revertible electrical machines, a gear transmission with four gears and a differential mechanism which transmits the motion at the driving wheels. For the study of the dynamical behavior, with numerical results, one designs such mechanisms, models the elements with solids in AutoCAD, and obtains the mechanical properties of the elements. Further on, we present and solve the equations of motion of a hybrid automotive for which one knows the dynamical parameters.

  10. Hybrid ligand-alkylating agents targeting telomeric G-quadruplex structures.

    Science.gov (United States)

    Doria, Filippo; Nadai, Matteo; Folini, Marco; Di Antonio, Marco; Germani, Luca; Percivalle, Claudia; Sissi, Claudia; Zaffaroni, Nadia; Alcaro, Stefano; Artese, Anna; Richter, Sara N; Freccero, Mauro

    2012-04-14

    The synthesis, physico-chemical properties and biological effects of a new class of naphthalene diimides (NDIs) capable of reversibly binding telomeric DNA and alkylate it through an electrophilic quinone methide moiety (QM), are reported. FRET and circular dichroism assays showed a marked stabilization and selectivity towards telomeric G4 DNA folded in a hybrid topology. NDI-QMs' alkylating properties revealed a good reactivity on single nucleosides and selectivity towards telomeric G4. A selected NDI was able to significantly impair the growth of melanoma cells by causing telomere dysfunction and down-regulation of telomerase expression. These findings points to our hybrid ligand-alkylating NDIs as possible tools for the development of novel targeted anticancer therapies. This journal is © The Royal Society of Chemistry 2012

  11. Structure of Mercury's magnetosphere for different pressure of the solar wind: Three dimensional hybrid simulations

    Czech Academy of Sciences Publication Activity Database

    Trávníček, Pavel; Hellinger, Petr; Schriver, D.

    2007-01-01

    Roč. 34, č. 5 (2007), L05104/1-L05104/5 ISSN 0094-8276 R&D Projects: GA ČR GA205/05/1011 Institutional research plan: CEZ:AV0Z30420517 Keywords : Global simulations * Mercury's magnetosphere * solar wind * hybrid simulations * ion drift driven rings Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.744, year: 2007

  12. Structure of the lunar wake: Two-dimensional global hybrid simulations

    Czech Academy of Sciences Publication Activity Database

    Trávníček, Pavel; Hellinger, Petr; Schriver, D.; Bale, S. D.

    2005-01-01

    Roč. 32, - (2005), L06102/1-L06102/4 ISSN 0094-8276 R&D Projects: GA ČR(CZ) GA205/05/1011 Grant - others:ESA(XE) PRODEX 14529; NSF(US) INT- 0010111; NASA (US) NAG5-11804 Institutional research plan: CEZ:AV0Z30420517 Keywords : hybrid simulations * lunar wake Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 2.491, year: 2005

  13. Photothermally Activated Pyroelectric Polymer Films for Harvesting of Solar Heat with a Hybrid Energy Cell Structure.

    Science.gov (United States)

    Park, Teahoon; Na, Jongbeom; Kim, Byeonggwan; Kim, Younghoon; Shin, Haijin; Kim, Eunkyoung

    2015-12-22

    Photothermal effects in poly(3,4-ethylenedioxythiophene)s (PEDOTs) were explored for pyroelectric conversion. A poled ferroelectric film was coated on both sides with PEDOT via solution casting polymerization of EDOT, to give highly conductive and effective photothermal thin films of PEDOT. The PEDOT films not only provided heat source upon light exposure but worked as electrodes for the output energy from the pyroelectric layer in an energy harvester hybridized with a thermoelectric layer. Compared to a bare thermoelectric system under NIR irradiation, the photothermal-pyro-thermoelectric device showed more than 6 times higher thermoelectric output with the additional pyroelectric output. The photothermally driven pyroelectric harvesting film provided a very fast electric output with a high voltage output (Vout) of 15 V. The pyroelectric effect was significant due to the transparent and high photothermal PEDOT film, which could also work as an electrode. A hybrid energy harvester was assembled to enhance photoconversion efficiency (PCE) of a solar cell with a thermoelectric device operated by the photothermally generated heat. The PCE was increased more than 20% under sunlight irradiation (AM 1.5G) utilizing the transmitted light through the photovoltaic cell as a heat source that was converted into pyroelectric and thermoelectric output simultaneously from the high photothermal PEDOT electrodes. Overall, this work provides a dynamic and static hybrid energy cell to harvest solar energy in full spectral range and thermal energy, to allow solar powered switching of an electrochromic display.

  14. Facile synthesis of graphene hybrid tube-like structure for simultaneous detection of ascorbic acid, dopamine, uric acid and tryptophan

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Wen [Education Ministry Key Laboratory on Luminescence and Real-Time Analysis, College of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China); Chai Yaqin, E-mail: yqchai@swu.edu.cn [Education Ministry Key Laboratory on Luminescence and Real-Time Analysis, College of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China); Yuan Ruo, E-mail: yuanruo@swu.edu.cn [Education Ministry Key Laboratory on Luminescence and Real-Time Analysis, College of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China); Chen Shihong; Han Jing; Yuan Dehua [Education Ministry Key Laboratory on Luminescence and Real-Time Analysis, College of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China)

    2012-12-05

    Graphical abstract: A tube-like structure of graphene hybrid (GS-PTCA) was synthesized via {pi}-{pi} stacking interaction, and was used as modifier to fabricate electrode for simultaneous detection of ascorbic acid (AA), dopamine (DA), uric acid (UA) and tryptophan (Trp). SEM images of GS, PTCA and GS-PTCA were presented. Under the synergistic effects between GS and PTCA, the modified electrode displayed high catalytic activity and selectivity toward the oxidation of AA, DA, UA, and Trp. Highlights: Black-Right-Pointing-Pointer A simple strategy for simultaneous detection of AA, DA, UA and Trp has been constructed. Black-Right-Pointing-Pointer The tube-like structure of graphene hybrid (GS-PTCA) was synthesized. Black-Right-Pointing-Pointer The GS-PTCA provided a selective interface for discrimination of AA, DA, UA and Trp. - Abstract: In the present work, a tube-like structure of graphene hybrid as modifier to fabricate electrode for simultaneous detection of ascorbic acid (AA), dopamine (DA), uric acid (UA) and tryptophan (Trp) was reported. The hybrid was synthesized by a simple method based on graphene sheets (GS) and 3,4,9,10-perylenetetracarboxylic acid (PTCA) via {pi}-{pi} stacking interaction under ultrasonic condition. The combination of GS and PTCA could effectively improve the dispersion of GS, owing to PTCA with the carboxylic-functionalized interface. Comparing with pure GS or PTCA modified electrode, GS-PTCA displayed high catalytic activity and selectivity toward the oxidation of AA, DA, UA, and Trp. Moreover, cyclic voltammetry, different pulse voltammetry and scanning electron microscopy were employed to characterize the sensors. The experiment results showed that the linear response range for simultaneous detection of AA, DA, UA, and Trp were 20-420 {mu}M, 0.40-374 {mu}M, 4-544 {mu}M and 0.40-138 {mu}M, respectively, and the detection limits were 5.60 {mu}M, 0.13 {mu}M, 0.92 {mu}M and 0.06 {mu}M (S/N = 3). Importantly, the proposed method offers

  15. Mesoscale hybrid calibration artifact

    Science.gov (United States)

    Tran, Hy D.; Claudet, Andre A.; Oliver, Andrew D.

    2010-09-07

    A mesoscale calibration artifact, also called a hybrid artifact, suitable for hybrid dimensional measurement and the method for make the artifact. The hybrid artifact has structural characteristics that make it suitable for dimensional measurement in both vision-based systems and touch-probe-based systems. The hybrid artifact employs the intersection of bulk-micromachined planes to fabricate edges that are sharp to the nanometer level and intersecting planes with crystal-lattice-defined angles.

  16. High performance light trapping structures for Si-based photoelectronics fabricated by hybrid picosecond laser irradiation and chemical corrosion

    Science.gov (United States)

    Ji, Lingfei; Lv, Xiaozhan; Wu, Yan; Lin, Zhenyuan; Jiang, Yijian

    2015-03-01

    We propose the fabrication of two types high performance texturized antireflective structures on crystalline (100) silicon (c-Si) surface by hybrid picosecond laser scanning irradiation followed by chemical corrosion. The design and the fabrication with high controllable performance were studied. The hybrid method includes 1064 nm picosecond (ps) laser scanning to form micro-hole array and subsequently short-time alkaline corrosion. After ps laser processing, there is little reconsolidation and heat affect zone on the silicon surface, which is beneficial to achieve the precise chemical corrosion effect. Depending on the laser scanning intervals, scanning times and chemical corrosion time, a variety of surface texture morphologies, even a special micro-nano hierarchical structure in which finer nano-structures formed in the micro units of the texture, were achieved. Observing with SEM, the average diameter of the micro-holes in the micro-nano hierarchica is 25~30 μm, while the average size of the nano-level ladder-like structures on the micro-hole wall is from dozens to hundreds of nanometers. Comparing to the traditional laser texturing techniques for c-Si solar cell, the whole laser processing was carried out in an open air ambient without using etch mask and SF6/O2 plasma. The results show the reflectance value of the fabricated c-Si surfaces can reach as low as 6% (400 nm~1000 nm). This is a potential method for economical antireflective structures fabrication which is ideal for using in the high-efficiency silicon-based photoelectronic devices.

  17. Internal structures of thermosensitive hybrid microgels investigated by means of small-angle X-ray scattering.

    Science.gov (United States)

    Suzuki, Daisuke; Nagase, Yasuhisa; Kureha, Takuma; Sato, Takaaki

    2014-02-27

    Internal structures of thermosensitive microgels and their hybrid counterparts that contain Au nanoparticles are investigated by means of small-angle X-ray scattering (SAXS). Thermosensitive cationic microgels were synthesized by aqueous free radical precipitation polymerization from N-isopropylacrylamide and 3-(methacrylamino) propyltrimethylammonium chloride used as monomers. Using the microgels as templates, Au nanoparticles were synthesized in situ, using the cationic sites in the microgel to nucleate particle growth. To obtain different types of the hybrid microgels, Au nanoparticles were synthesized in the presence of the microgels by changing the reduction conditions of the precursor ions, such as temperature and species of reducing reagent. The hybrid microgels were characterized mainly by TEM and SAXS. For SAXS investigation, the hybrid microgels were analyzed in the wide q-range of 0.07 nm(-1) < q < 20 nm(-1), where q is the magnitude of the scattering vector. A quantitative description of the scattering intensities, I(q), for the nonhybrid microgels requires a sum of five components having different physical origins. An upturn increase of the forward intensity originates from the interface of microgels, obeying the Porod law, I(q) ∝ q(-4). An additional Guinier term found in q < 0.2 nm(-1) seems to arise from solidlike density fluctuation due to the inhomogeneities of chemical cross-links. The power-law behavior manifested in the low- to intermediate-q range is directly linked with the fractal nature of the swollen (coil) polymer networks and well described by the Ornstein-Zernike equation. Two interference peaks centered at q ≈ 5 nm (-1) and q ≈ 15 nm(-1) are likely to reflect inter- and intrachain correlations of pNIPAm, respectively, which are formally fitted by pseudo-Voigt equations. As for the hybrid microgels, a pronounced new contribution from the Au nanoparticles emerges, which calls for an additional scattering component describing

  18. Application of nonlinear rheology to assess the effect of secondary nanofiller on network structure of hybrid polymer nanocomposites

    Science.gov (United States)

    Kamkar, Milad; Aliabadian, Ehsan; Shayesteh Zeraati, Ali; Sundararaj, Uttandaraman

    2018-02-01

    Carbon nanotube (CNT)/polymer nanocomposites exhibit excellent electrical properties by forming a percolated network. Adding a secondary filler can significantly affect the CNTs' network, resulting in changing the electrical properties. In this work, we investigated the effect of adding manganese dioxide nanowires (MnO2NWs) as a secondary nanofiller on the CNTs' network structure inside a poly(vinylidene fluoride) (PVDF) matrix. Incorporating MnO2NWs to PVDF/CNT samples produced a better state of dispersion of CNTs, as corroborated by light microscopy and transmission electron microscopy. The steady shear and oscillatory shear flows were employed to obtain a better insight into the nanofiller structure and viscoelastic behavior of the nanocomposites. The transient response under steady shear flow revealed that the stress overshoot of hybrid nanocomposites (two-fillers), PVDF/CNT/MnO2NWs, increased dramatically in comparison to binary nanocomposites (single-filler), PVDF/CNT and PVDF/MnO2NWs. This can be attributed to microstructural changes. Large amplitude oscillatory shear characterization was also performed to further investigate the effect of the secondary nanofiller on the nonlinear viscoelastic behavior of the samples. The nonlinear rheological observations were explained using quantitative nonlinear parameters [strain-stiffening ratio (S) and shear-thickening ratio (T)] and Lissajous-Bowditch plots. Results indicated that a more rigid nanofiller network was formed for the hybrid nanocomposites due to the better dispersion state of CNTs and this led to a more nonlinear viscoelastic behavior.

  19. When the lowest energy does not induce native structures: parallel minimization of multi-energy values by hybridizing searching intelligences.

    Directory of Open Access Journals (Sweden)

    Qiang Lü

    Full Text Available BACKGROUND: Protein structure prediction (PSP, which is usually modeled as a computational optimization problem, remains one of the biggest challenges in computational biology. PSP encounters two difficult obstacles: the inaccurate energy function problem and the searching problem. Even if the lowest energy has been luckily found by the searching procedure, the correct protein structures are not guaranteed to obtain. RESULTS: A general parallel metaheuristic approach is presented to tackle the above two problems. Multi-energy functions are employed to simultaneously guide the parallel searching threads. Searching trajectories are in fact controlled by the parameters of heuristic algorithms. The parallel approach allows the parameters to be perturbed during the searching threads are running in parallel, while each thread is searching the lowest energy value determined by an individual energy function. By hybridizing the intelligences of parallel ant colonies and Monte Carlo Metropolis search, this paper demonstrates an implementation of our parallel approach for PSP. 16 classical instances were tested to show that the parallel approach is competitive for solving PSP problem. CONCLUSIONS: This parallel approach combines various sources of both searching intelligences and energy functions, and thus predicts protein conformations with good quality jointly determined by all the parallel searching threads and energy functions. It provides a framework to combine different searching intelligence embedded in heuristic algorithms. It also constructs a container to hybridize different not-so-accurate objective functions which are usually derived from the domain expertise.

  20. When the Lowest Energy Does Not Induce Native Structures: Parallel Minimization of Multi-Energy Values by Hybridizing Searching Intelligences

    Science.gov (United States)

    Lü, Qiang; Xia, Xiao-Yan; Chen, Rong; Miao, Da-Jun; Chen, Sha-Sha; Quan, Li-Jun; Li, Hai-Ou

    2012-01-01

    Background Protein structure prediction (PSP), which is usually modeled as a computational optimization problem, remains one of the biggest challenges in computational biology. PSP encounters two difficult obstacles: the inaccurate energy function problem and the searching problem. Even if the lowest energy has been luckily found by the searching procedure, the correct protein structures are not guaranteed to obtain. Results A general parallel metaheuristic approach is presented to tackle the above two problems. Multi-energy functions are employed to simultaneously guide the parallel searching threads. Searching trajectories are in fact controlled by the parameters of heuristic algorithms. The parallel approach allows the parameters to be perturbed during the searching threads are running in parallel, while each thread is searching the lowest energy value determined by an individual energy function. By hybridizing the intelligences of parallel ant colonies and Monte Carlo Metropolis search, this paper demonstrates an implementation of our parallel approach for PSP. 16 classical instances were tested to show that the parallel approach is competitive for solving PSP problem. Conclusions This parallel approach combines various sources of both searching intelligences and energy functions, and thus predicts protein conformations with good quality jointly determined by all the parallel searching threads and energy functions. It provides a framework to combine different searching intelligence embedded in heuristic algorithms. It also constructs a container to hybridize different not-so-accurate objective functions which are usually derived from the domain expertise. PMID:23028708

  1. Thermal transport in topological-insulator-based superconducting hybrid structures with mixed singlet and triplet pairing states.

    Science.gov (United States)

    Li, Hai; Zhao, Yuan Yuan

    2017-11-22

    In the framework of the Bogoliubov-de Gennes equation, we investigate the thermal transport properties in topological-insulator-based superconducting hybrid structures with mixed spin-singlet and spin-triplet pairing states, and emphasize the different manifestations of the spin-singlet and spin-triplet pairing states in the thermal transport signatures. It is revealed that the temperature-dependent differential thermal conductance strongly depends on the components of the pairing state, and the negative differential thermal conductance only occurs in the spin-singlet pairing state dominated regime. It is also found that the thermal conductance is profoundly sensitive to the components of the pairing state. In the spin-singlet pairing state controlled regime, the thermal conductance obviously oscillates with the phase difference and junction length. With increasing the proportion of the spin-triplet pairing state, the oscillating characteristic of the thermal conductance fades out distinctly. These results suggest an alternative route for distinguishing the components of pairing states in topological-insulator-based superconducting hybrid structures.

  2. Platinum-TM (TM = Fe, Co) alloy nanoparticles dispersed nitrogen doped (reduced graphene oxide-multiwalled carbon nanotube) hybrid structure cathode electrocatalysts for high performance PEMFC applications.

    Science.gov (United States)

    Vinayan, B P; Ramaprabhu, S

    2013-06-07

    The efforts to push proton exchange membrane fuel cells (PEMFC) for commercial applications are being undertaken globally. In PEMFC, the sluggish kinetics of oxygen reduction reactions (ORR) at the cathode can be improved by the alloying of platinum with 3d-transition metals (TM = Fe, Co, etc.) and with nitrogen doping, and in the present work we have combined both of these aspects. We describe a facile method for the synthesis of a nitrogen doped (reduced graphene oxide (rGO)-multiwalled carbon nanotubes (MWNTs)) hybrid structure (N-(G-MWNTs)) by the uniform coating of a nitrogen containing polymer over the surface of the hybrid structure (positively surface charged rGO-negatively surface charged MWNTs) followed by the pyrolysis of these (rGO-MWNTs) hybrid structure-polymer composites. The N-(G-MWNTs) hybrid structure is used as a catalyst support for the dispersion of platinum (Pt), platinum-iron (Pt3Fe) and platinum-cobalt (Pt3Co) alloy nanoparticles. The PEMFC performances of Pt-TM alloy nanoparticle dispersed N-(G-MWNTs) hybrid structure electrocatalysts are 5.0 times higher than that of commercial Pt-C electrocatalysts along with very good stability under acidic environment conditions. This work demonstrates a considerable improvement in performance compared to existing cathode electrocatalysts being used in PEMFC and can be extended to the synthesis of metal, metal oxides or metal alloy nanoparticle decorated nitrogen doped carbon nanostructures for various electrochemical energy applications.

  3. Structure and properties of hybrid poly(2-hydroxyethyl methacrylate)/SiO2 monoliths

    DEFF Research Database (Denmark)

    Ji, Xiangling; Jiang, Shichun; Qiu, Xuepeng

    2003-01-01

    region, that is, good transparency. Mechanical properties were studied with an Instron tester, and the monoliths exhibited better compressive strength and modulus than did bulk PHEMA. Surprisingly, thermogravimetric analysis (TGA) data showed greater than 50 wt % solid residue up to 700degreesC, possibly......Abstract: Hybrid poly(2-hydroxyethyl methacrylate) (PHEMA)/SiO2 monoliths were synthesized via a sol-gel process of the precursor tetraethyl orthosilicate (TEOS) and the in situ free-radical polymerization of 2-hydroxyethyl methacrylate (HEMA). The weight ratio of the starting chemicals, TEOS...

  4. Quantum teleportation and entanglement swapping of electron spins in superconducting hybrid structures

    Energy Technology Data Exchange (ETDEWEB)

    Bubanja, Vladimir, E-mail: vladimir.bubanja@callaghaninnovation.govt.nz

    2015-06-15

    We present schemes for quantum teleportation and entanglement swapping of electronic spin states in hybrid superconductor–normal-metal systems. The proposed schemes employ subgap transport whereby the lowest order processes involve Cooper pair-electron and double Cooper-pair cotunneling in quantum teleportation and entanglement swapping protocols, respectively. The competition between elastic cotunneling and Cooper-pair splitting results in the success probability of 25% in both cases. Described implementations of these protocols are within reach of present-day experimental techniques.

  5. Hybrid-DFT  +  V w method for band structure calculation of semiconducting transition metal compounds: the case of cerium dioxide

    Science.gov (United States)

    Ivády, Viktor; Gali, Adam; Abrikosov, Igor A.

    2017-11-01

    Hybrid functionals’ non-local exchange-correlation potential contains a derivative discontinuity that improves on standard semi-local density functional theory (DFT) band gaps. Moreover, by careful parameterization, hybrid functionals can provide self-interaction reduced description of selected states. On the other hand, the uniform description of all the electronic states of a given system is a known drawback of these functionals that causes varying accuracy in the description of states with different degrees of localization. This limitation can be remedied by the orbital dependent exact exchange extension of hybrid functionals; the hybrid-DFT  +  V w method (Ivády et al 2014 Phys. Rev. B 90 035146). Based on the analogy of quasi-particle equations and hybrid-DFT single particle equations, here we demonstrate that parameters of hybrid-DFT  +  V w functional can be determined from approximate theoretical quasi-particle spectra without any fitting to experiment. The proposed method is illustrated on the charge self-consistent electronic structure calculation for cerium dioxide where itinerant valence states interact with well-localized 4f atomic like states, making this system challenging for conventional methods, either hybrid-DFT or LDA  +  U, and therefore allowing for a demonstration of the advantages of the proposed scheme.

  6. Hybrid-DFT  +  Vwmethod for band structure calculation of semiconducting transition metal compounds: the case of cerium dioxide.

    Science.gov (United States)

    Ivády, Viktor; Gali, Adam; Abrikosov, Igor A

    2017-11-15

    Hybrid functionals' non-local exchange-correlation potential contains a derivative discontinuity that improves on standard semi-local density functional theory (DFT) band gaps. Moreover, by careful parameterization, hybrid functionals can provide self-interaction reduced description of selected states. On the other hand, the uniform description of all the electronic states of a given system is a known drawback of these functionals that causes varying accuracy in the description of states with different degrees of localization. This limitation can be remedied by the orbital dependent exact exchange extension of hybrid functionals; the hybrid-DFT  +  V w method (Ivády et al 2014 Phys. Rev. B 90 035146). Based on the analogy of quasi-particle equations and hybrid-DFT single particle equations, here we demonstrate that parameters of hybrid-DFT  +  V w functional can be determined from approximate theoretical quasi-particle spectra without any fitting to experiment. The proposed method is illustrated on the charge self-consistent electronic structure calculation for cerium dioxide where itinerant valence states interact with well-localized 4f atomic like states, making this system challenging for conventional methods, either hybrid-DFT or LDA  +  U, and therefore allowing for a demonstration of the advantages of the proposed scheme.

  7. Chromium and nickel ion irradiation effects on the low- and high-temperature metal-semiconductor transitions in (V1 - xCrx)2O3 ceramics

    Science.gov (United States)

    Kokabi, H. R.; Studer, F.

    1996-11-01

    Chromium doped vanadium sesquioxide [(V1-xCrx)2O3] ceramic samples have been irradiated using medium energy chromium and nickel ions (52Cr:572 MeV, 64Ni:640 MeV) at various fluences (4×1011-1.1×1014 ions/cm2) and doping rates (x=0.3, 0.6, and 0.7). Irradiation has been carried out under vacuum and at room temperature. Irradiated samples have been characterized by electrical resistivity measurements as a function of temperature for the low- and the high-temperature transitions in the (V1-xCrx)2O3 system. Irradiation by chromium and nickel ions creates bilayered samples as the ions mean projected range were smaller than the sample thickness. The bilayer structure is characterized by two transitions at low temperature. Dealing with the high temperature positive temperature coefficient transition, the negative temperature coefficient behavior above this transition has been considerably attenuated due to the bilayered structure. In situ measurements on an irradiated sample have shown that after annealing the electrical characteristics for the low- and the high-temperature transitions tend to be close to those of an unirradiated sample. However, even an annealing at 380 °C does not eliminate all the irradiation effects.

  8. Position calibration of a 3-DOF hand-controller with hybrid structure

    Science.gov (United States)

    Zhu, Chengcheng; Song, Aiguo

    2017-09-01

    A hand-controller is a human-robot interactive device, which measures the 3-DOF (Degree of Freedom) position of the human hand and sends it as a command to control robot movement. The device also receives 3-DOF force feedback from the robot and applies it to the human hand. Thus, the precision of 3-DOF position measurements is a key performance factor for hand-controllers. However, when using a hybrid type 3-DOF hand controller, various errors occur and are considered originating from machining and assembly variations within the device. This paper presents a calibration method to improve the position tracking accuracy of hybrid type hand-controllers by determining the actual size of the hand-controller parts. By re-measuring and re-calibrating this kind of hand-controller, the actual size of the key parts that cause errors is determined. Modifying the formula parameters with the actual sizes, which are obtained in the calibrating process, improves the end position tracking accuracy of the device.

  9. Tamm-plasmon and surface-plasmon hybrid-mode based refractometry in photonic bandgap structures.

    Science.gov (United States)

    Das, Ritwick; Srivastava, Triranjita; Jha, Rajan

    2014-02-15

    The transverse magnetic (TM) polarized hybrid modes formed as a consequence of coupling between Tamm plasmon polariton (TM-TPP) mode and surface plasmon polariton (SPP) mode exhibit interesting dispersive features for realizing a highly sensitive and accurate surface plasmon resonance (SPR) sensor. We found that the TM-TPP modes, formed at the interface of distributed Bragg reflector and metal, are strongly dispersive as compared to SPP modes at optical frequencies. This causes an appreciably narrow interaction bandwidth between TM-TPP and SPP modes, which leads to highly accurate sensing. In addition, appropriate tailoring of dispersion characteristics of TM-TPP as well as SPP modes could ensure high sensitivity of a novel SPR platform. By suitably designing the Au/TiO₂/SiO₂-based geometry, we propose a TM-TPP/SPP hybrid-mode sensor and achieve a sensitivity ≥900  nm/RIU with high detection accuracy (≥30  μm⁻¹) for analyte refractive indices varying between 1.330 and 1.345 in 600-700 nm wavelength range. The possibility to achieve desired dispersive behavior in any spectral band makes the sensing configuration an extremely attractive candidate to design sensors depending on the availability of optical sources.

  10. Position calibration of a 3-DOF hand-controller with hybrid structure.

    Science.gov (United States)

    Zhu, Chengcheng; Song, Aiguo

    2017-09-01

    A hand-controller is a human-robot interactive device, which measures the 3-DOF (Degree of Freedom) position of the human hand and sends it as a command to control robot movement. The device also receives 3-DOF force feedback from the robot and applies it to the human hand. Thus, the precision of 3-DOF position measurements is a key performance factor for hand-controllers. However, when using a hybrid type 3-DOF hand controller, various errors occur and are considered originating from machining and assembly variations within the device. This paper presents a calibration method to improve the position tracking accuracy of hybrid type hand-controllers by determining the actual size of the hand-controller parts. By re-measuring and re-calibrating this kind of hand-controller, the actual size of the key parts that cause errors is determined. Modifying the formula parameters with the actual sizes, which are obtained in the calibrating process, improves the end position tracking accuracy of the device.

  11. Nanowire Structured Hybrid Cell for Concurrently Scavenging Solar and Mechanical Energies

    KAUST Repository

    Xu, Chen

    2009-04-29

    Conversion cells for harvesting solar energy and mechanical energy are usually separate and independent entities that are designed and built following different physical principles. Developing a technology that harvests multiple-type energies in forms such as sun light and mechanical around the clock is desperately desired for fully utilizing the energies available in our living environment. We report a hybrid cell that is intended for simultaneously harvesting solar and mechanical energies. Using aligned ZnO nanowire arrays grown on surfaces of a flat substrate, a dye-sensitized solar cell is integrated with a piezoelectric nanogenerator. The former harvests solar energy irradiating on the top, and the latter harvests ultrasonic wave energy from the surrounding. The two energy harvesting approaches can work simultaneously or individually, and they can be integrated in parallel and serial for raising the output current and voltage, respectively, as well as power. It is found that the voltage output from the solar cell can be used to raise the output voltage of the nanogenerator, providing an effective approach for effectively storing and utilizing the power generated by the nanogenerator. Our study demonstrates a new approach for concurrently harvesting multiple types of energies using an integrated hybrid cell so that the energy resources can be effectively and complementary utilized whenever and wherever one or all of them is available. © 2009 American Chemical Society.

  12. Cassava/sugar palm fiber reinforced cassava starch hybrid composites: Physical, thermal and structural properties.

    Science.gov (United States)

    Edhirej, Ahmed; Sapuan, S M; Jawaid, Mohammad; Zahari, Nur Ismarrubie

    2017-08-01

    A hybrid composite was prepared from cassava bagasse (CB) and sugar palm fiber (SPF) using casting technique with cassava starch (CS) as matrix and fructose as a plasticizer. Different loadings of SPF (2, 4, 6 and 8% w/w of dry starch) were added to the CS/CB composite film containing 6% CB. The addition of SPF significantly influenced the physical properties. It increased the thickness while decreasing the density, water content, water solubility and water absorption. However, no significant effect was noticed on the thermal properties of the hybrid composite film. The incorporation of SPF increased the relative crystallinity up to 47%, compared to 32% of the CS film. SEM micrographs indicated that the filler was incorporated in the matrix. The film with a higher concentration of SPF (CS-CB/SPF8) showed a more heterogeneous surface. It could be concluded that the incorporation of SPF led to changes in cassava starch film properties, potentially affecting the film performances. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Structural properties of hybrid star with CFL locking in quark phase

    International Nuclear Information System (INIS)

    Thakur, Suman; Dhimany, Shashi K.

    2017-01-01

    Compact stars are some of the densest manifestations of massive objects in the universe. They are ideal astrophysical laboratories for testing theories of dense matter physics and provide connections among nuclear physics, particle physics, and astrophysics. Compact stars may exhibit conditions and phenomena not observed elsewhere, such as hyperon-dominated matter, deconfined quark matter, superconductivity with critical temperatures near 10"1"0 kelvin, opaqueness to neutrinos, and magnetic fields in excess of 10"1"8 Gauss. The appearance of quark matter or hadron-quark mixed phase in the massive neutron stars is a hot topic in the study of compact objects. A family of compact stars consisting completely of the deconfined mixture of u, d, s quarks has been called Quark stars. The compact stars with a quark matter core, either as a hadron-quark mixed phase or as a pure quark phase, are called hybrid stars (HyS). The main objective of present work is to investigate the Equations of State and Mass - Radius relationship of Hybrid Matter Star. Here the Hadron phase id described within the frame-work of FTRMF model and Quark phase is described within the framework of Quark Quasiparticle (QQPM) model

  14. Facile synthesis of analogous graphene quantum dots with sp2 hybridized carbon atom dominant structures and their photovoltaic application

    Science.gov (United States)

    Huang, Zhengcheng; Shen, Yongtao; Li, Yu; Zheng, Wenjun; Xue, Yunjia; Qin, Chengqun; Zhang, Bo; Hao, Jingxiang; Feng, Wei

    2014-10-01

    Graphene quantum dot (GQD) is an emerging class of zero-dimensional nanocarbon material with many novel applications. It is of scientific importance to prepare GQDs with more perfect structures, that is, GQDs containing negligible oxygenous defects, for both optimizing their optical properties and helping in their photovoltaic applications. Herein, a new strategy for the facile preparation of ``pristine'' GQDs is reported. The method we presented is a combination of a bottom-up synthetic and a solvent-induced interface separation process, during which the target products with highly crystalline structure were selected by the organic solvent. The obtained organic soluble GQDs (O-GQDs) showed a significant difference in structure and composition compared with ordinary aqueous soluble GQDs, thus leading to a series of novel properties. Furthermore, O-GQDs were applied as electron-acceptors in a poly(3-hexylthiophene) (P3HT)-based organic photovoltaic device. The performance highlights that O-GQD has potential to be a novel electron-acceptor material due to the sp2 hybridized carbon atom dominant structure and good solubility in organic solvents.Graphene quantum dot (GQD) is an emerging class of zero-dimensional nanocarbon material with many novel applications. It is of scientific importance to prepare GQDs with more perfect structures, that is, GQDs containing negligible oxygenous defects, for both optimizing their optical properties and helping in their photovoltaic applications. Herein, a new strategy for the facile preparation of ``pristine'' GQDs is reported. The method we presented is a combination of a bottom-up synthetic and a solvent-induced interface separation process, during which the target products with highly crystalline structure were selected by the organic solvent. The obtained organic soluble GQDs (O-GQDs) showed a significant difference in structure and composition compared with ordinary aqueous soluble GQDs, thus leading to a series of novel

  15. Hybrid functional calculated optical and electronic structures of thin anatase TiO2 nanowires with organic dye adsorbates

    International Nuclear Information System (INIS)

    Ünal, Hatice; Gunceler, Deniz; Gülseren, Oğuz; Ellialtıoğlu, Şinasi; Mete, Ersen

    2015-01-01

    Highlights: • Size effect on the band gap features of thin anatase (0 0 1) and (1 0 1) nanowires calculated at the screened Coulomb hybrid DFT approach. • HSE-optimized structures of coumarin and donor-pi-acceptor type C2-1 dye adsorbates on anatase (0 0 1) and (1 0 1) nanowires. • HSE charge density distributions of frontier states of dye-nanowire systems. • HSE + PCM calculations for C2-1 and coumarin on anatase nanowires including nonlinear solvation environment effects. • Optical properties of dye + nanowire combined systems. - Abstract: The electronic and optical properties of thin anatase TiO 2 (1 0 1) and (0 0 1) nanowires have been investigated using the screened Coulomb hybrid density functional calculations. For the bare nanowires with sub-nanometer diameters, the calculated band gaps are larger relative to the bulk values due to size effects. The role of organic light harvesting sensitizers on the absorption characteristics of the anatase nanowires has been examined using the hybrid density functional method incorporating partial exact exchange with range separation. For the lowest lying excitations, directional charge redistribution of tetrahydroquinoline (C2-1) dye shows a remarkably different profile in comparison to a simple molecule which is chosen as the coumarin skeleton. The binding modes and the adsorption energies of C2-1 dye and coumarin core on the anatase nanowires have been studied including non-linear solvation effetcs. The calculated optical and electronic properties of the nanowires with these two different types of sensitizers have been interpreted in terms of their electron–hole generation, charge carrier injection and recombination characteristics.

  16. Syntheses, structures and properties of four organic-inorganic hybrid nicotinate-bridging rare-earth-containing phosphotungstates

    Science.gov (United States)

    Gong, Peijun; Pang, Jingjing; Zhai, Cuiping; Zhao, Junwei

    2018-04-01

    Four novel organic-inorganic hybrid nicotinate-bridging dimeric rare-earth (RE)-containing phosphotungstates [H2N(CH3)2]8[RE(H2O)(NA)(α-HPW11O39)]2·24H2O (RE = HoIII for 1, ErIII for 2, TbIII for 3, DyIII for 4; HNA = nicotinic acid) have been synthesized from the reaction of trivacant Keggin precursor Na9[α-PW9O34]•16H2O, RE(NO3)3·6H2O, HNA by employing dimethylamine hydrochloride as organic solubilizing agent in the conventional aqueous solution system, which have been further characterized by elemental analyses, IR spectra, thermogravimetric analyses and single-crystal X-ray diffraction. Structural analysis indicates that the hybrid dimeric {[RE(H2O)(NA)(α-HPW11O39)]2}8- polyoxoanion in 1-4 can be considered as two head-to-head mono-RE-containing Keggin [RE(H2O)(NA)(α-HPW11O39)]4- subunits bridged by two (η2,μ-1,1)-nicotinate linkers, which stands for the first organic-inorganic hybrid RE-containing phosphotungstates functionalized by nicotinate ligands. What's more, the solid-state photoluminescence properties and lifetime decay behaviors of 1-4 have been measured at room temperature and their photoluminescence spectra display the characteristic emission bands of corresponding trivalent RE cations.

  17. Structural Performance of a Hybrid FRP-Aluminum Modular Triangular Truss System Subjected to Various Loading Conditions

    Directory of Open Access Journals (Sweden)

    Dongdong Zhang

    2014-01-01

    Full Text Available A novel hybrid FRP-aluminum truss system has been employed in a two-rut modular bridge superstructure composed of twin inverted triangular trusses. The actual flexural behavior of a one-rut truss has been previously investigated under the on-axis loading test; however, the structural performance of the one-rut truss subjected to an off-axis load is still not fully understood. In this paper, a geometrical linear finite element model is introduced and validated by the on-axis loading test; the structural performance of the one-rut truss subjected to off-axis load was numerically obtained; the dissimilarities of the structural performance between the two different loading cases are investigated in detail. The results indicated that (1 the structural behavior of the off-axis load differs from that of the on-axis load, and the off-axis load is the critical loading condition controlling the structural performance of the triangular truss; (2 under the off-axis load, the FRP trussed members and connectors bear certain out-of-plane bending moments and are subjected to a complicated stress state; and (3 the stress state of these members does not match that of the initial design, and optimization for the redesign of these members is needed, especially for the pretightened teeth connectors.

  18. The Simulation Calculations And Dielectric Characteristics Investigation of a Hybrid Dielectric-Iris-Loaded Travelling Accelerating Structure

    CERN Document Server

    Wu, C F

    2004-01-01

    Mafia code has been used to calculate the RF properties versus the geometric parameters and dielectric permittivity of the X-band (f=9.37 GHz) hybrid dielectric-iris-loaded travelling accelerating structure. The simulation results show that when the range of the permittivity is about 5–9 and the geometric parameters are optimized, the new structure may have lower ratio (about 1) of peak surface electric field at the iris to axial accelerating electric field , while r, Q, r/Q of the new structure being comparable to iris-loaded accelerating structure. The experimental investigation of the permittivity of the dielectric (ceramic)has been made by using the cavity perturbation technique. The results show that the permittivity of the ceramic is about 5.8 at the X-band and its stability is good.The above results will be applied to the design of the new accelerating structure, which may be a potential candidate of high gradient Linear accelerator.

  19. Mechanical Property Analysis on Sandwich Structured Hybrid Composite Made from Natural Fibre, Glass Fibre and Ceramic Fibre Wool Reinforced with Epoxy Resin

    Science.gov (United States)

    Bharat, K. R.; Abhishek, S.; Palanikumar, K.

    2017-06-01

    Natural fibre composites find wide range of applications and usage in the automobile and manufacturing industries. They find lack in desired properties, which are required for present applications. In current scenario, many developments in composite materials involve the synthesis of Hybrid composite materials to overcome some of the lacking properties. In this present investigation, two sandwich structured hybrid composite materials have been made by reinforcing Aloe Vera-Ceramic Fibre Wool-Glass fibre with Epoxy resin matrix and Sisal fibre-Ceramic Fibre Wool-Glass fibre with Epoxy resin matrix and its mechanical properties such as Tensile, Flexural and Impact are tested and analyzed. The test results from the two samples are compared and the results show that sisal fibre reinforced hybrid composite has better mechanical properties than aloe vera reinforced hybrid composite.

  20. Structural change of the physical economy. Decomposition analysis of physical and hybrid-unit input-output tables

    International Nuclear Information System (INIS)

    Hoekstra, R.

    2003-01-01

    Economic processes generate a variety of material flows, which cause resource problems through the depletion of natural resources and environmental issues due to the emission of pollutants. This thesis presents an analytical method to study the relationship between the monetary economy and the 'physical economy'. In particular, this method can assess the impact of structural change in the economy on physical throughput. The starting point for the approach is the development of an elaborate version of the physical input-output table (PIOT), which acts as an economic-environmental accounting framework for the physical economy. In the empirical application, hybrid-unit input-output (I/O) tables, which combine physical and monetary information, are constructed for iron and steel, and plastic products for the Netherlands for the years 1990 and 1997. The impact of structural change on material flows is analyzed using Structural Decomposition Analysis (SDA), whic specifies effects such as sectoral shifts, technological change, and alterations in consumer spending and international trade patterns. The study thoroughly reviews the application of SDA to environmental issues, compares the method with other decomposition methods, and develops new mathematical specifications. An SDA is performed using the hybrid-unit input-output tables for the Netherlands. The results are subsequently used in novel forecasting and backcasting scenario analyses for the period 1997-2030. The results show that dematerialization of iron and steel, and plastics, has generally not occurred in the recent past (1990-1997), and will not occur, under a wide variety of scenario assumptions, in the future (1997-2030)

  1. Structural change of the physical economy. Decomposition analysis of physical and hybrid-unit input-output tables

    Energy Technology Data Exchange (ETDEWEB)

    Hoekstra, R.

    2003-10-01

    Economic processes generate a variety of material flows, which cause resource problems through the depletion of natural resources and environmental issues due to the emission of pollutants. This thesis presents an analytical method to study the relationship between the monetary economy and the 'physical economy'. In particular, this method can assess the impact of structural change in the economy on physical throughput. The starting point for the approach is the development of an elaborate version of the physical input-output table (PIOT), which acts as an economic-environmental accounting framework for the physical economy. In the empirical application, hybrid-unit input-output (I/O) tables, which combine physical and monetary information, are constructed for iron and steel, and plastic products for the Netherlands for the years 1990 and 1997. The impact of structural change on material flows is analyzed using Structural Decomposition Analysis (SDA), whic specifies effects such as sectoral shifts, technological change, and alterations in consumer spending and international trade patterns. The study thoroughly reviews the application of SDA to environmental issues, compares the method with other decomposition methods, and develops new mathematical specifications. An SDA is performed using the hybrid-unit input-output tables for the Netherlands. The results are subsequently used in novel forecasting and backcasting scenario analyses for the period 1997-2030. The results show that dematerialization of iron and steel, and plastics, has generally not occurred in the recent past (1990-1997), and will not occur, under a wide variety of scenario assumptions, in the future (1997-2030)

  2. Quantum size effects on spin-transfer torque in a double barrier magnetic tunnel junction with a nonmagnetic-metal (semiconductor) spacer

    International Nuclear Information System (INIS)

    Daqiq, Reza; Ghobadi, Nader

    2016-01-01

    We study the quantum size effects of an MgO-based double barrier magnetic tunnel junction with a nonmagnetic-metal (DBMTJ-NM) (semiconductor (DBMTJ-SC)) spacer on the charge current and the spin-transfer torque (STT) components using non-equilibrium Green's function (NEGF) formalism. The results show oscillatory behavior due to the resonant tunneling effect depending on the structure parameters. We find that the charge current and the STT components in the DBMTJ-SC demonstrate the magnitude enhancement in comparison with the DBMTJ-NM. The bias dependence of the STT components in a DBMTJ-NM shows different behavior in comparison with spin valves and conventional MTJs. Therefore, by choosing a specific SC spacer with suitable thickness in a DBMTJ the charge current and the STT components significantly increase so that one can design a device with high STT and faster magnetization switching. - Highlights: • The quantum size effects are studied in double barrier magnetic tunnel junctions. • Spin torque (ST) components oscillate for increasing of middle spacer thicknesses. • Due to the resonant tunneling in the quantum well, oscillations have appeared. • By replacement a metal spacer with a semiconductor (ZnO) ST has increased. • The ST components vs. bias show gradually decreasing unlike spin valves or MTJs.

  3. Studies and mechanical properties of a new type of 'hybrid' ceramic block for buildings in structural masonry

    International Nuclear Information System (INIS)

    Camara, Cassio Freire; Gomes, Uilame Umbelino

    2012-01-01

    This paper presents the development of a hybrid ceramic block to the use of resides in the buildings executed with structural masonry. This work seeking new materials and / or products with the purpose of increasing the compressive strength of the ceramic blocks, without neglecting other properties (water absorption and linear shrinkage). After the obtained material (clay powder and crushed), the packaging (in percentages ranging from 0%, 5%, 10% and 15% substitution of crushed clay powder), the identification and measuring (weights and lengths) of the bodies of the test piece, was performed on the approach characterized by fluorescence, mineralogy and SEM of these materials as well as the characterization (SEM) of ceramic blocks after the sintering (temperature of the 900 deg C, 1000 deg C, and 1100 deg C rate with heating tax of 5 o C/minute and soak for 1 hour). Then the samples were subjected to the tests (compressive strength and water absorption) and the respective calculated linear shrinkage. After conducting the analysis of the results of these tests (according to the criteria and parameters required by the ABNT NBR 15270) was found that the 'hybrid' block with the addition of 10% crushed powder obtained the best results, increasing the compressive strength at 16 % without compromising the other parameters required by the Standard. (author)

  4. Carbon nanotubes randomly decorated with gold clusters: from nano2hybrid atomic structures to gas sensing prototypes

    International Nuclear Information System (INIS)

    Charlier, J-C; Zanolli, Z; Arnaud, L; Avilov, I V; Felten, A; Pireaux, J-J; Delgado, M; Demoisson, F; Reniers, F; Espinosa, E H; Ionescu, R; Leghrib, R; Llobet, E; Ewels, C P; Suarez-Martinez, I; Guillot, J; Mansour, A; Migeon, H-N; Watson, G E

    2009-01-01

    Carbon nanotube surfaces, activated and randomly decorated with metal nanoclusters, have been studied in uniquely combined theoretical and experimental approaches as prototypes for molecular recognition. The key concept is to shape metallic clusters that donate or accept a fractional charge upon adsorption of a target molecule, and modify the electron transport in the nanotube. The present work focuses on a simple system, carbon nanotubes with gold clusters. The nature of the gold-nanotube interaction is studied using first-principles techniques. The numerical simulations predict the binding and diffusion energies of gold atoms at the tube surface, including realistic atomic models for defects potentially present at the nanotube surface. The atomic structure of the gold nanoclusters and their effect on the intrinsic electronic quantum transport properties of the nanotube are also predicted. Experimentally, multi-wall CNTs are decorated with gold clusters using (1) vacuum evaporation, after activation with an RF oxygen plasma and (2) colloid solution injected into an RF atmospheric plasma; the hybrid systems are accurately characterized using XPS and TEM techniques. The response of gas sensors based on these nano 2 hybrids is quantified for the detection of toxic species like NO 2 , CO, C 2 H 5 OH and C 2 H 4 .

  5. Carbon nanotubes randomly decorated with gold clusters: from nano{sup 2}hybrid atomic structures to gas sensing prototypes

    Energy Technology Data Exchange (ETDEWEB)

    Charlier, J-C; Zanolli, Z [Unite de Physico-Chimie et de Physique des Materiaux (PCPM), European Theoretical Spectroscopy Facility (ETSF), Universite Catholique de Louvain, Place Croix du Sud 1, B-1348 Louvain-la-Neuve (Belgium); Arnaud, L; Avilov, I V; Felten, A; Pireaux, J-J [Centre de Recherche en Physique de la Matiere et du Rayonnement (PMR-LISE), Facultes Universitaires Notre-Dame de la Paix, 61 Rue de Bruxelles, B-5000 Namur (Belgium); Delgado, M [Sensotran, s.l., Avenida Remolar 31, E-08820 El Prat de Llobregat, Barcelona (Spain); Demoisson, F; Reniers, F [Service de Chimie Analytique et Chimie des Interfaces (CHANI), Universite Libre de Bruxelles, Faculte des Sciences, CP255, Boulevard du Triomphe 2, B-1050 Bruxelles (Belgium); Espinosa, E H; Ionescu, R; Leghrib, R; Llobet, E [Department of Electronic Engineering, Universitat Rovira i Virgili, Avenida Paisos Catalans 26, E-43007 Tarragona (Spain); Ewels, C P; Suarez-Martinez, I [Institut des Materiaux Jean Rouxel (IMN), Universite de Nantes, 2 rue de la Houssiniere-BP 32229, F-44322 Nantes Cedex 3 (France); Guillot, J; Mansour, A; Migeon, H-N [Departement Science et Analyse des Materiaux, Centre de Recherche Public-Gabriel Lippmann, rue du Brill 41, L-4422 Belvaux (Luxembourg); Watson, G E, E-mail: jean-jacques.pireaux@fundp.ac.b [Vega Science Trust, Unit 118, Science Park SQ, Brighton, BN1 9SB (United Kingdom)

    2009-09-16

    Carbon nanotube surfaces, activated and randomly decorated with metal nanoclusters, have been studied in uniquely combined theoretical and experimental approaches as prototypes for molecular recognition. The key concept is to shape metallic clusters that donate or accept a fractional charge upon adsorption of a target molecule, and modify the electron transport in the nanotube. The present work focuses on a simple system, carbon nanotubes with gold clusters. The nature of the gold-nanotube interaction is studied using first-principles techniques. The numerical simulations predict the binding and diffusion energies of gold atoms at the tube surface, including realistic atomic models for defects potentially present at the nanotube surface. The atomic structure of the gold nanoclusters and their effect on the intrinsic electronic quantum transport properties of the nanotube are also predicted. Experimentally, multi-wall CNTs are decorated with gold clusters using (1) vacuum evaporation, after activation with an RF oxygen plasma and (2) colloid solution injected into an RF atmospheric plasma; the hybrid systems are accurately characterized using XPS and TEM techniques. The response of gas sensors based on these nano{sup 2}hybrids is quantified for the detection of toxic species like NO{sub 2}, CO, C{sub 2}H{sub 5}OH and C{sub 2}H{sub 4}.

  6. ARTEMIS observations of lunar wake structure compared with hybrid ­kinetic simulations and an analytic model

    Science.gov (United States)

    Gharaee, H.; Rankin, R.; Marchand, R.; Paral, J.

    2014-12-01

    The ARTEMIS mission has made extensive measurements on the density and magnetic field structure of the lunar wake under different solar wind and magnetosphere conditions. Hybrid-kinetic simulations of the lunar wake have been found to be generally in good agreement with observations [Wiehle, S., et al., Planet. Space Sci., 2011], but are not readily available as they require access to large computers and human resources with expertise using this technology. It would be very useful to have an analytic model of the lunar wake, and one such model will be presented. It is based on an approach outlined by Hutchinson [Hutchinson, I., Physics Of Plasmas, 2008], and makes assumptions of cylindrical geometry, a strong and constant magnetic field, and fixed transverse velocity and temperature. Under these approximations the ion fluid equations (with massless electrons assumed) can be solved analytically by the method of characteristics. This paper demonstrates that the analytic model under these assumptions provides excellent agreement with observations and hybrid-kinetic simulations of the lunar wake. The approach outlined by Hutchinson is generalized to include an arbitrary angle between the interplanetary magnetic field and solar wind flow. This results in two angle-dependent characteristics for the fluid flow that can be solved for the density inside the wake region. The Density profiles for different orientations of magnetic field with respect to solar wind flow are in a good qualitative agreement with 2D Hybrid simulation results of the model developed by [Paral and Rankin, Nature Comms, 2012], and with ARTEMIS observations. Refrences, -Wiehle, S., et al. (2011), First Lunar wake passage of Artemis: Discrimination of wake effects and solar wind flactuations by 3D hybrid simulations, Planet. Space Sci., 59, 661-671, doi:10.1016/j.pss.2011.01.012. -Hutchinson, I. (2008),Oblique ion collection in the drift approximation:How magnetized Mach probes really work, Physics Of

  7. Hybrid nanocomposite based on cellulose and tin oxide: growth, structure, tensile and electrical characteristics

    International Nuclear Information System (INIS)

    Mahadeva, Suresha K; Kim, Jaehwan

    2011-01-01

    A highly flexible nanocomposite was developed by coating a regenerated cellulose film with a thin layer of tin oxide (SnO 2 ) by liquid-phase deposition. Tin oxide was crystallized in solution and formed nanocrystal coatings on regenerated cellulose. The nanocrystalline layers did not exfoliate from cellulose. Transmission electron microscopy and energy dispersive x-ray spectroscopy suggest that SnO 2 was not only deposited over the cellulose surface, but also nucleated and grew inside the cellulose film. Current-voltage characteristics of the nanocomposite revealed that its electrical resistivity decreases with deposition time, with the lowest value obtained for 24 h of deposition. The cellulose-SnO 2 hybrid nanocomposite can be used for biodegradable and disposable chemical, humidity and biosensors.

  8. Strain-controlled magnetic domain wall propagation in hybrid piezoelectric/ferromagnetic structures.

    Science.gov (United States)

    Lei, Na; Devolder, Thibaut; Agnus, Guillaume; Aubert, Pascal; Daniel, Laurent; Kim, Joo-Von; Zhao, Weisheng; Trypiniotis, Theodossis; Cowburn, Russell P; Chappert, Claude; Ravelosona, Dafiné; Lecoeur, Philippe

    2013-01-01

    The control of magnetic order in nanoscale devices underpins many proposals for integrating spintronics concepts into conventional electronics. A key challenge lies in finding an energy-efficient means of control, as power dissipation remains an important factor limiting future miniaturization of integrated circuits. One promising approach involves magnetoelectric coupling in magnetostrictive/piezoelectric systems, where induced strains can bear directly on the magnetic anisotropy. While such processes have been demonstrated in several multiferroic heterostructures, the incorporation of such complex materials into practical geometries has been lacking. Here we demonstrate the possibility of generating sizeable anisotropy changes, through induced strains driven by applied electric fields, in hybrid piezoelectric/spin-valve nanowires. By combining magneto-optical Kerr effect and magnetoresistance measurements, we show that domain wall propagation fields can be doubled under locally applied strains. These results highlight the prospect of constructing low-power domain wall gates for magnetic logic devices.

  9. Optimization of an extraordinary magnetoresistance sensor in the semiconductor-metal hybrid structure

    KAUST Repository

    Sun, Jian

    2010-11-01

    The purpose of this paper is to show by numerical computation how geometric parameters influence the Extraordinary Magnetoresistance (EMR) effect in an InAs-Au hybrid device. Symmetric IVVI and VIIV configurations were considered. The results show that the width and the length-width ratio of InAs are important geometrical parameters for the EMR effect along with the placement of the leads. Approximately the same EMR effect was obtained for both IVVI and VIIV configurations when the applied magnetic field ranged from -1T to 1T. In an optimized geometry the EMR effect can reach 43000% at 1Tesla for IVVI and 42700% at 1 Tesla for the VIIV configuration. ©2010 IEEE.

  10. Hybrid DNA i-motif: Aminoethylprolyl-PNA (pC5) enhance the stability of DNA (dC5) i-motif structure.

    Science.gov (United States)

    Gade, Chandrasekhar Reddy; Sharma, Nagendra K

    2017-12-15

    This report describes the synthesis of C-rich sequence, cytosine pentamer, of aep-PNA and its biophysical studies for the formation of hybrid DNA:aep-PNAi-motif structure with DNA cytosine pentamer (dC 5 ) under acidic pH conditions. Herein, the CD/UV/NMR/ESI-Mass studies strongly support the formation of stable hybrid DNA i-motif structure with aep-PNA even near acidic conditions. Hence aep-PNA C-rich sequence cytosine could be considered as potential DNA i-motif stabilizing agents in vivo conditions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Construction of a novel hierarchical structured NH4-Co-Ni phosphate toward an ultrastable aqueous hybrid capacitor

    Science.gov (United States)

    Chen, Zhaoyang; Xiong, Ding-Bang; Zhang, Xuejiao; Ma, Hongnan; Xia, Meirong; Zhao, Yufeng

    2016-03-01

    Aqueous hybrid capacitors (HCs) suffer from sacrificed power density and long cycle life due to the insufficient electric conductivity and poor chemical stability of the battery-type electrode material. Herein, we report a novel NH4-Co-Ni phosphate with a stable hierarchical structure combining ultrathin nanopieces and single crystal microplatelets in one system, which allows for a synergistic integration of two microstructures with different length scales and different energy storage mechanisms. The microplatelets with a stable single crystal structure store charge through the intercalation of hydroxyl ions, while the ultrathin nanopieces store charge through surface redox reaction providing enhanced specific capacitance. Furthermore, the large single crystal can bridge the small nanopieces forming continuous electronic conduction paths as well as ionic conduction channels, and facilitate both electron and ion transportation in the hierarchical structure. The HC cell based on the as prepared material and a 3D hierarchical porous carbon delivers a high energy density of 29.6 Wh kg-1 at a high power density of 11 kW kg-1. Particularly, an ultralong cycle life along with 93.5% capacitance retention after 10 000 charge-discharge cycles is achieved, which is outstanding among the state-of-the-art aqueous HC cells.Aqueous hybrid capacitors (HCs) suffer from sacrificed power density and long cycle life due to the insufficient electric conductivity and poor chemical stability of the battery-type electrode material. Herein, we report a novel NH4-Co-Ni phosphate with a stable hierarchical structure combining ultrathin nanopieces and single crystal microplatelets in one system, which allows for a synergistic integration of two microstructures with different length scales and different energy storage mechanisms. The microplatelets with a stable single crystal structure store charge through the intercalation of hydroxyl ions, while the ultrathin nanopieces store charge through

  12. Investigation of CO2 capture mechanisms of liquid-like nanoparticle organic hybrid materials via structural characterization

    KAUST Repository

    Park, Youngjune

    2011-01-01

    Nanoparticle organic hybrid materials (NOHMs) have been recently developed that comprise an oligomeric or polymeric canopy tethered to surface-modified nanoparticles via ionic or covalent bonds. It has already been shown that the tunable nature of the grafted polymeric canopy allows for enhanced CO 2 capture capacity and selectivity via the enthalpic intermolecular interactions between CO2 and the task-specific functional groups, such as amines. Interestingly, for the same amount of CO2 loading NOHMs have also exhibited significantly different swelling behavior compared to that of the corresponding polymers, indicating a potential structural effect during CO2 capture. If the frustrated canopy species favor spontaneous ordering due to steric and/or entropic effects, the inorganic cores of NOHMs could be organized into unusual structural arrangements. Likewise, the introduction of small gaseous molecules such as CO2 could reduce the free energy of the frustrated canopy. This entropic effect, the result of unique structural nature, could allow NOHMs to capture CO2 more effectively. In order to isolate the entropic effect, NOHMs were synthesized without the task-specific functional groups. The relationship between their structural conformation and the underlying mechanisms for the CO2 absorption behavior were investigated by employing NMR and ATR FT-IR spectroscopies. The results provide fundamental information needed for evaluating and developing novel liquid-like CO2 capture materials and give useful insights for designing and synthesizing NOHMs for more effective CO2 capture. © the Owner Societies 2011.

  13. Facile synthesis of analogous graphene quantum dots with sp(2) hybridized carbon atom dominant structures and their photovoltaic application.

    Science.gov (United States)

    Huang, Zhengcheng; Shen, Yongtao; Li, Yu; Zheng, Wenjun; Xue, Yunjia; Qin, Chengqun; Zhang, Bo; Hao, Jingxiang; Feng, Wei

    2014-11-07

    Graphene quantum dot (GQD) is an emerging class of zero-dimensional nanocarbon material with many novel applications. It is of scientific importance to prepare GQDs with more perfect structures, that is, GQDs containing negligible oxygenous defects, for both optimizing their optical properties and helping in their photovoltaic applications. Herein, a new strategy for the facile preparation of "pristine" GQDs is reported. The method we presented is a combination of a bottom-up synthetic and a solvent-induced interface separation process, during which the target products with highly crystalline structure were selected by the organic solvent. The obtained organic soluble GQDs (O-GQDs) showed a significant difference in structure and composition compared with ordinary aqueous soluble GQDs, thus leading to a series of novel properties. Furthermore, O-GQDs were applied as electron-acceptors in a poly(3-hexylthiophene) (P3HT)-based organic photovoltaic device. The performance highlights that O-GQD has potential to be a novel electron-acceptor material due to the sp(2) hybridized carbon atom dominant structure and good solubility in organic solvents.

  14. 3D printing of high-resolution PLA-based structures by hybrid electrohydrodynamic and fused deposition modeling techniques

    International Nuclear Information System (INIS)

    Zhang, Bin; Seong, Baekhoon; Byun, Doyoung; Nguyen, VuDat

    2016-01-01

    Recently, the three-dimensional (3D) printing technique has received much attention for shape forming and manufacturing. The fused deposition modeling (FDM) printer is one of the various 3D printers available and has become widely used due to its simplicity, low-cost, and easy operation. However, the FDM technique has a limitation whereby its patterning resolution is too low at around 200 μm. In this paper, we first present a hybrid mechanism of electrohydrodynamic jet printing with the FDM technique, which we name E-FDM. We then develop a novel high-resolution 3D printer based on the E-FDM process. To determine the optimal condition for structuring, we also investigated the effect of several printing parameters, such as temperature, applied voltage, working height, printing speed, flow-rate, and acceleration on the patterning results. This method was capable of fabricating both high resolution 2D and 3D structures with the use of polylactic acid (PLA). PLA has been used to fabricate scaffold structures for tissue engineering, which has different hierarchical structure sizes. The fabrication speed was up to 40 mm/s and the pattern resolution could be improved to 10 μm. (paper)

  15. Effect of polyvinyl alcohol content and after synthesis neutralization on structure, mechanical properties and cytotoxicity of sol-gel derived hybrid foams

    Directory of Open Access Journals (Sweden)

    Agda Aline Rocha de Oliveira

    2009-06-01

    Full Text Available Bioactive glass/polymer hybrids are promising materials for biomedical applications because they combine the bioactivity of these glasses with the flexibility of polymers. In this work it was evaluated the effect of increasing the PVA content of the on structural characteristics and mechanical properties of hybrid. The hybrids were prepared with 70 wt. (% SiO2-30 wt. (% CaO and PVA fractions of 20 to 60 wt. (% by the sol-gel method. The structural and mechanical characterization was done by FTIR, SEM and compression tests. To reduce the acidic character of the hybrids due to the catalysts added, different neutralization solutions were tested. The calcium acetate alcoholic solution was the best neutralizing method, resulting in foams with final pH of about 7.0 and small sample contraction. The foams presented porosity of 60-85 wt. (% and pore diameters of 100-500 μm with interconnected structure. An increase of PVA fraction in the hybrids improved their mechanical properties. The scaffolds produced provided a good environment for the adhesion and proliferation of osteoblasts.

  16. ORION: a web server for protein fold recognition and structure prediction using evolutionary hybrid profiles.

    Science.gov (United States)

    Ghouzam, Yassine; Postic, Guillaume; Guerin, Pierre-Edouard; de Brevern, Alexandre G; Gelly, Jean-Christophe

    2016-06-20

    Protein structure prediction based on comparative modeling is the most efficient way to produce structural models when it can be performed. ORION is a dedicated webserver based on a new strategy that performs this task. The identification by ORION of suitable templates is performed using an original profile-profile approach that combines sequence and structure evolution information. Structure evolution information is encoded into profiles using structural features, such as solvent accessibility and local conformation -with Protein Blocks-, which give an accurate description of the local protein structure. ORION has recently been improved, increasing by 5% the quality of its results. The ORION web server accepts a single protein sequence as input and searches homologous protein structures within minutes. Various databases such as PDB, SCOP and HOMSTRAD can be mined to find an appropriate structural template. For the modeling step, a protein 3D structure can be directly obtained from the selected template by MODELLER and displayed with global and local quality model estimation measures. The sequence and the predicted structure of 4 examples from the CAMEO server and a recent CASP11 target from the 'Hard' category (T0818-D1) are shown as pertinent examples. Our web server is accessible at http://www.dsimb.inserm.fr/ORION/.

  17. An ultra-thin dual-band phase-gradient metasurface using hybrid resonant structures for backward RCS reduction

    Science.gov (United States)

    Cheng, Yongzhi; Wu, Chenjun; Ge, Chenchen; Yang, Jiaji; Pei, Xiaojun; Jia, Fan; Gong, Rongzhou

    2017-05-01

    We introduce and investigate, both experimentally and theoretically, a dual-band phase-gradient metasurface (PGM) to accurately facilitate dual-band beams deflection for electromagnetic waves. The designed PGM is composed of two kinds of split-ring resonators as the basic element of a super cell. These hybrid resonant structures can generate phase gradients at two distinct frequencies, which, in turn, generate appropriately artificial wave vectors that meet the requirements for anomalous reflection in terms of generalized Snell's law. Both simulations and experiments are consistent with the theoretical predictions. Further, this PGM can work at 8.9 and 11.4 GHz frequencies providing a phenomenon of anomalous reflection, which is useful for backward radar cross section reduction.

  18. Shape-Encoded Chitosan-Polyacrylamide Hybrid Hydrogel Microparticles with Controlled Macroporous Structures via Replica Molding for Programmable Biomacromolecular Conjugation.

    Science.gov (United States)

    Kang, Eunae; Jung, Sukwon; Abel, John H; Pine, Allison; Yi, Hyunmin

    2016-05-31

    Polymeric hydrogel microparticle-based suspension arrays with shape-based encoding offer powerful alternatives to planar and bead-based arrays toward high throughput biosensing and medical diagnostics. We report a simple and robust micromolding technique for polyacrylamide- (PAAm-) based biopolymeric-synthetic hybrid microparticles with controlled 2D shapes containing a potent aminopolysaccharide chitosan as an efficient conjugation handle uniformly incorporated in PAAm matrix. A postfabrication conjugation approach utilizing amine-reactive chemistries on the chitosan shows stable incorporation and retained chemical reactivity of chitosan, readily tunable macroporous structures via simple addition of low content long-chain PEG porogens for improved conjugation capacity and kinetics, and one-pot biomacromolecular assembly via bioorthogonal click reactions with minimal nonspecific binding. We believe that the integrated fabrication-conjugation approach reported here could offer promising routes to programmable manufacture of hydrogel microparticle-based biomacromolecular conjugation and biofunctionalization platforms for a large range of applications.

  19. Stationary transport in mesoscopic hybrid structures with contacts to superconducting and normal wires: A Green's function approach for multiterminal setups

    Science.gov (United States)

    Arrachea, Liliana

    2009-03-01

    We generalize the representation of the real-time Green’s functions introduced by Langreth and Nordlander [Phys. Rev. B 43, 2541 (1991)] and Meir and Wingreen [Phys. Rev. Lett. 68, 2512 (1992)] in stationary quantum transport in order to study problems with hybrid structures containing normal (N) and superconducting (S) pieces without introducing Nambu representation. We illustrate the treatment in a S-N junction under a stationary bias. We derive expressions for the normal and Andreev transmission functions, and we show the equivalence between these expressions and Blonder-Tinkham-Klapwijk formulation. Finally, we investigate in detail the behavior of the equilibrium currents in a normal ring threaded by a magnetic flux with attached superconducting wires at equilibrium. We analyze the flux sensitivity of the Andreev states, and we show that their response is equivalent to the one corresponding to the Cooper pairs with momentum q=0 in an isolated superconducting ring.

  20. High Efficiency Flexible Battery Based on Graphene-carbon Nanotube Hybrid Structure

    Science.gov (United States)

    2015-02-26

    nanotube field emitter structure on three- dimensional micro-channeled copper , Appl. Phys. Lett. (2012) 1 7. Carbon Nanostructures in Lithium Ion...Electrochemical performance of the 3D MWCNTs-graphene-PET as a flexible LIB anode structure. (a) Initial galvanostatic charge and discharge profiles of 3D...grown on copper We present a novel binder-free multi-wall carbon nanotube (MWCNT) structure as anode in Li- ion batteries. The interface-controlled

  1. Dimensional structure of DSM-5 posttraumatic stress symptoms: support for a hybrid Anhedonia and Externalizing Behaviors model.

    Science.gov (United States)

    Armour, Cherie; Tsai, Jack; Durham, Tory A; Charak, Ruby; Biehn, Tracey L; Elhai, Jon D; Pietrzak, Robert H

    2015-02-01

    Several revisions to the symptom clusters of posttraumatic stress disorder (PTSD) have been made in the 5th edition of the Diagnostic and Statistical Manual of Mental Disorders (DSM-5). Central to the focus of this study was the revision of PTSD's tripartite structure in DSM-IV into four symptom clusters in DSM-5. Emerging confirmatory factor analytic (CFA) studies have suggested that DSM-5 PTSD symptoms may be best represented by one of two 6-factor models: (1) an Externalizing Behaviors model characterized by a factor which combines the irritability/anger and self-destructive/reckless behavior items; and (2) an Anhedonia model characterized by items of loss of interest, detachment, and restricted affect. The current study conducted CFAs of DSM-5 PTSD symptoms assessed using the PTSD Checklist for DSM-5 (PCL-5) in two independent and diverse trauma-exposed samples of a nationally representative sample of 1484 U.S. veterans and a sample of 497 Midwestern U.S. university undergraduate students. Relative fits of the DSM-5 model, the DSM-5 Dysphoria model, the DSM-5 Dysphoric Arousal model, the two 6-factor models, and a newly proposed 7-factor Hybrid model, which consolidates the two 6-factor models, were evaluated. Results revealed that, in both samples, both 6-factor models provided significantly better fit than the 4-factor DSM-5 model, the DSM-5 Dysphoria model and the DSM-5 Dysphoric Arousal model. Further, the 7-factor Hybrid model, which incorporates key features of both 6-factor models and is comprised of re-experiencing, avoidance, negative affect, anhedonia, externalizing behaviors, and anxious and dysphoric arousal symptom clusters, provided superior fit to the data in both samples. Results are discussed in light of theoretical and empirical support for the latent structure of DSM-5 PTSD symptoms. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Experimental and numerical analysis of a hybrid FBG long gauge sensor for structural health monitoring

    International Nuclear Information System (INIS)

    Górriz, Benjamín Torres; García, Pedro Calderón; Payá-Zaforteza, Ignacio J; Maicas, Salvador Sales

    2014-01-01

    This paper presents a new long gauge sensor for structural health monitoring based on the use of fiber Bragg gratings. The proposed sensor has the advantage over existing sensors that it does not require prestressing of the optical fiber. The development consisted of numerical studies complemented by experimental tests to analyze: (1) the strain transfer between the sensor and the host structure; (2) the influence of sensor axial stiffness on the structural behavior of the host structure; (3) the influence of the mechanical properties of the adhesive used to fix the sensor and (4) the failure modes of the sensor (buckling and shear stress of sensor anchors). (paper)

  3. Ferroelectric coupling effect on the energy-band structure of hybrid heterojunctions with self-organized P(VDF-TrFE) nanomatrices.

    Science.gov (United States)

    Shin, Kyung-Sik; Kim, Tae Yun; Yoon, Gyu Cheol; Gupta, Manoj Kumar; Kim, Sung Kyun; Seung, Wanchul; Kim, Hyeok; Kim, Sungjin; Kim, SeongMin; Kim, Sang-Woo

    2014-08-27

    Ferroelectric coupling effects on the energy-band structure of hybrid heterojunctions are investigated using hybrid photovoltaic devices with poly(3-hexylthiophene-2,5-diyl) (P3HT)/ZnO and poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)). The self-organized P(VDF-TrFE):P3HT photoactive layer forms a novel architecture consisting of P3HT domains in a P(VDF-TrFE) matrix. The energy-band structure at the interface of the p-n heterojunction is tuned by artificial control of the ferroelectric polarization of the P(VDF-TrFE) material, consequently modulating the photovoltaic performance of the hybrid photovoltaic devices. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Carbon Nanotube Enhanced Aerospace Composite Materials A New Generation of Multifunctional Hybrid Structural Composites

    CERN Document Server

    Kostopoulos, V

    2013-01-01

    The well documented increase in the use of high performance composites as structural materials in aerospace components is continuously raising the demands in terms of dynamic performance, structural integrity, reliable life monitoring systems and adaptive actuating abilities. Current technologies address the above issues separately; material property tailoring and custom design practices aim to the enhancement of dynamic and damage tolerance characteristics, whereas life monitoring and actuation is performed with embedded sensors that may be detrimental to the structural integrity of the component. This publication explores the unique properties of carbon nanotubes (CNT) as an additive in the matrix of Fibre Reinforced Plastics (FRP), for producing structural composites with improved mechanical performance as well as sensing/actuating capabilities. The successful combination of the CNT properties and existing sensing actuating technologies leads to the realization of a multifunctional FRP structure. The curre...

  5. Integrated Multi-Color Light Emitting Device Made with Hybrid Crystal Structure

    Science.gov (United States)

    Park, Yeonjoon (Inventor); Choi, Sang Hyouk (Inventor)

    2017-01-01

    An integrated hybrid crystal Light Emitting Diode ("LED") display device that may emit red, green, and blue colors on a single wafer. The various embodiments may provide double-sided hetero crystal growth with hexagonal wurtzite III-Nitride compound semiconductor on one side of (0001) c-plane sapphire media and cubic zinc-blended III-V or II-VI compound semiconductor on the opposite side of c-plane sapphire media. The c-plane sapphire media may be a bulk single crystalline c-plane sapphire wafer, a thin free standing c-plane sapphire layer, or crack-and-bonded c-plane sapphire layer on any substrate. The bandgap energies and lattice constants of the compound semiconductor alloys may be changed by mixing different amounts of ingredients of the same group into the compound semiconductor. The bandgap energy and lattice constant may be engineered by changing the alloy composition within the cubic group IV, group III-V, and group II-VI semiconductors and within the hexagonal III-Nitrides.

  6. On the Hamiltonian structure of large deviations in stochastic hybrid systems

    Science.gov (United States)

    Bressloff, Paul C.; Faugeras, Olivier

    2017-03-01

    We present a new derivation of the classical action underlying a large deviation principle (LDP) for a stochastic hybrid system, which couples a piecewise deterministic dynamical system in {{{R}}d} with a time-homogeneous Markov chain on some discrete space Γ . We assume that the Markov chain on Γ is ergodic, and that the discrete dynamics is much faster than the piecewise deterministic dynamics (separation of time-scales). Using the Perron-Frobenius theorem and the calculus-of-variations, we show that the resulting action Hamiltonian is given by the Perron eigenvalue of a | Γ | -dimensional linear equation. The corresponding linear operator depends on the transition rates of the Markov chain and the nonlinear functions of the piecewise deterministic system. We compare the Hamiltonian to one derived using WKB methods, and show that the latter is a reduction of the former. We also indicate how the analysis can be extended to a multi-scale stochastic process, in which the continuous dynamics is described by a piecewise stochastic differential equations (SDE). Finally, we illustrate the theory by considering applications to conductance-based models of membrane voltage fluctuations in the presence of stochastic ion channels.

  7. Integrated Multi-Color Light Emitting Device Made with Hybrid Crystal Structure

    Science.gov (United States)

    Park, Yeonjoon (Inventor); Choi, Sang Hyouk (Inventor)

    2016-01-01

    An integrated hybrid crystal Light Emitting Diode ("LED") display device that may emit red, green, and blue colors on a single wafer. The various embodiments may provide double-sided hetero crystal growth with hexagonal wurtzite III-Nitride compound semiconductor on one side of (0001) c-plane sapphire media and cubic zinc-blended III-V or II-VI compound semiconductor on the opposite side of c-plane sapphire media. The c-plane sapphire media may be a bulk single crystalline c-plane sapphire wafer, a thin free standing c-plane sapphire layer, or crack-and-bonded c-plane sapphire layer on any substrate. The bandgap energies and lattice constants of the compound semiconductor alloys may be changed by mixing different amounts of ingredients of the same group into the compound semiconductor. The bandgap energy and lattice constant may be engineered by changing the alloy composition within the cubic group IV, group III-V, and group II-VI semiconductors and within the hexagonal III-Nitrides.

  8. Adhesive Bonding Techniques in Hybrid Structures Made from Fibre Reinforced Polymeric Composites and Concrete

    Directory of Open Access Journals (Sweden)

    Ruxandra Oltean

    2009-01-01

    Full Text Available Mechanical joining techniques are used in construction industry all over the world on a daily basis. A further method of joining has proven to be highly successful – adhesive bonding. Known for thousands of years, adhesive bonding has become as important as other joining techniques as a result of the pace of developments in recent years. In many areas, this bonding technology has become a key technology. Virtually, all solid materials can be connected with one another using adhesives. Although bonding fibre reinforced polymeric composites to the concrete substrate is a relatively simple technique, the proper installation of the fibre reinforced polymeric composites is essential to ensure the adequate performance of the hybrid system. Since the installation procedures differ from one system to another, appropriate specifications will be clearly presented. The paper will include requirements to provide a quality joint assembly, meaning the special pre-treatments of the concrete surface. The material to be bonded is cleaned and prepared so that adhesives can adhere better to them.

  9. Hybrid time-variant reliability estimation for active control structures under aleatory and epistemic uncertainties

    Science.gov (United States)

    Wang, Lei; Xiong, Chuang; Wang, Xiaojun; Li, Yunlong; Xu, Menghui

    2018-04-01

    Considering that multi-source uncertainties from inherent nature as well as the external environment are unavoidable and severely affect the controller performance, the dynamic safety assessment with high confidence is of great significance for scientists and engineers. In view of this, the uncertainty quantification analysis and time-variant reliability estimation corresponding to the closed-loop control problems are conducted in this study under a mixture of random, interval, and convex uncertainties. By combining the state-space transformation and the natural set expansion, the boundary laws of controlled response histories are first confirmed with specific implementation of random items. For nonlinear cases, the collocation set methodology and fourth Rounge-Kutta algorithm are introduced as well. Enlightened by the first-passage model in random process theory as well as by the static probabilistic reliability ideas, a new definition of the hybrid time-variant reliability measurement is provided for the vibration control systems and the related solution details are further expounded. Two engineering examples are eventually presented to demonstrate the validity and applicability of the methodology developed.

  10. Crystal structure and anisotropic c-f hybridization in CeT2Al10 (T=Ru, Fe)

    International Nuclear Information System (INIS)

    Sera, Masafumi; Tanaka, Daiki; Tanida, Hiroshi

    2013-01-01

    We have performed the investigation of the charge density distribution of CeT 2 Al 10 (T=Ru, Fe) and the crystal structure parameters of LnT 2 Al 10 . The lattice parameters of a-, b-, and c-axes exhibit the anisotropic contraction when Ru is replaced by Fe in LnT 2 Al 10 , different from the isotropic contraction simply expected from the smaller ionic radius of Fe than Ru. The contraction is larger in the a- and c-axes than in the b-axis. This anisotropic contraction of the YbFe 2 Al 10 -type crystal structure originates from the zigzag degree of the zigzag chain formed by T and Al bond along the a- and c-axes are larger than that along the b-axis. The lattice parameters of CeT 2 Al 10 (T=Ru, Fe) exhibit the anisotropic deviation from the lanthanide contraction. The deviation is largest in the a-axis and is very small in the b-axis. Both the characteristic YbFe 2 Al 10 -type crystal structure and the anisotropic deviation towards the intermediate valence indicate that the largest c-f hybridization along the a-axis plays the important role and is associated with the unusual antiferromagnetic order in CeT 2 Al 10 (T=Ru, Os). (author)

  11. Inorganic–organic hybrid materials through post-synthesis modification: Impact of the treatment with azides on the mesopore structure

    Directory of Open Access Journals (Sweden)

    Miriam Keppeler

    2011-08-01

    Full Text Available Hybrid, hierarchically organized, monolithic silica gels, comprising periodically arranged mesopores and a cellular macroscopic network, have been prepared through a co-condensation reaction of tetrakis(2-hydroxyethylorthosilicate with chloromethyl-trimethoxysilane or 3-(chloropropyl-triethoxysilane. Subsequent conversion of the chloro groups into azido groups, by nucleophilic substitution with NaN3 in N,N-dimethylformamide, was conducted upon preservation of the monolithic structure. However, treatment with NaN3 had a strong influence on the structure in the mesoporous regime, with changes such as an increase of mesopore diameter, pore volume and lattice constants, as well as a concomitant decrease of the pore wall thickness, as confirmed by small angle X-ray scattering, transmission electron microscopy, and nitrogen sorption analysis. Similar effects were observed for unmodified silica gels by simple ageing in azide-containing media, whether a relatively small or a sterically demanding counter ion (Na+ or (H3C4N+ was used. The structural modification did not seem to depend greatly on whether an organic aprotic solvent (N,N-dimethylformamide, 1,1,3,3-tetramethylurea, 1,3-dimethyl-2-imidazolidinone or a protic solvent that can form hydrogen bonds, such as water, was used.

  12. Prediction of transmission, reflection and absorption coefficients of periodic structures using a hybrid Wave Based - Finite Element unit cell method

    Science.gov (United States)

    Deckers, Elke; Jonckheere, Stijn; Van Belle, Lucas; Claeys, Claus; Desmet, Wim

    2018-03-01

    This paper presents a hybrid Wave Based Method - Finite Element unit cell method to predict the absorption, reflection and transmission properties of arbitrary, two-dimensional periodic structures. The planar periodic structure, represented by its unit cell combined with Bloch-Floquet periodicity boundary conditions, is modelled within the Finite Element Method, allowing to represent complex geometries and to include any type of physics. The planar periodic structure is coupled to semi-infinite acoustic domains above and/or below, in which the dynamic pressure field is modelled with the Wave Based Method, applying a wave function set that fulfills the Helmholtz equation and satisfies the Sommerfeld radiation condition and the Bloch-Floquet periodicity conditions inherently. The dynamic fields described within both frameworks are coupled using a direct coupling strategy, accounting for the mutual dynamic interactions via a weighted residual formulation. The method explicitly accounts for the interaction between the unit cell and the surrounding acoustic domain, also accounting for higher order periodic waves. The convergence of the method is analysed and its applicability is shown for a variety of problems, proving it to be a useful tool combining the strengths of two methods.

  13. Hot-injection synthesis of Ni-ZnO hybrid nanocrystals with tunable magnetic properties and enhanced photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Deqian; Qiu, Yulong; Chen, Yuanzhi, E-mail: yuanzhi@xmu.edu.cn; Zhang, Qinfu; Liu, Xiang; Peng, Dong-Liang, E-mail: dlpeng@xmu.edu.cn [Xiamen University, Department of Materials Science and Engineering, Fujian Provincial Key Laboratory of Materials Genome, Collaborative Innovation Center of Chemistry for Energy Materials, College of Materials (China)

    2017-04-15

    Magnetic metal-semiconductor hybrid nanocrystals containing ferromagnetic Ni and semiconductor ZnO have been prepared via a hot-injection route. The Ni-ZnO hybrid nanocrystals have a flower-like morphology that consists of Ni inner cores and ZnO petal shells. In spite of their large lattice mismatch, ZnO nanocrystals can still grow on faceted Ni nanocrystals to form stable interfaces. The composition of Ni-ZnO hybrid nanocrystals is readily controlled, and the average size of Ni core is tunable from 25 to 50 nm. Room temperature ferromagnetic properties are observed in these hybrid nanocrystals, and tunable magnetic properties also can be achieved by varying the size of Ni core. The as-prepared Ni-ZnO hybrid nanocrystals exhibit enhanced photocatalytic performance under ultraviolet light illumination as compared to pure ZnO nanocrystals. Furthermore, the superior reusability of hybrid nanocrystals for photocatalytic application is achieved by virtue of their magnetic properties. The facile and efficient seed-mediate strategy is particularly attractive to construct hybrid magnetic-semiconducting heterostructures. The as-obtained Ni-ZnO hybrid nanocrystals offer great potential for various applications due to their combined magnetic and semiconducting properties and low-cost earth-abundant availability.

  14. Electronic structure and transport in graphene/haeckelite hybrids: an ab initio study

    International Nuclear Information System (INIS)

    Zhu, Zhen; Fthenakis, Zacharias G; Tománek, David

    2015-01-01

    We combine ab initio density functional theory (DFT) structural studies with DFT-based nonequilibrium Green's function calculations to investigate how the presence of non-hexagonal rings affects electronic transport in graphitic structures. We find that infinite monolayers, finite-width nanoribbons, and nanotubes formed of 5–8 haeckelite with only 5- and 8-membered rings are generally more conductive than their graphene-based counterparts. The presence of haeckelite defect lines in the perfect graphitic structure, a model of grain boundaries in CVD-grown graphene, increases the electronic conductivity and renders it highly anisotropic. (paper)

  15. Antigenic and 3D structural characterization of soluble X4 and hybrid X4-R5 HIV-1 Env trimers.

    Science.gov (United States)

    Arnold, Philipp; Himmels, Patricia; Weiß, Svenja; Decker, Tim-Michael; Markl, Jürgen; Gatterdam, Volker; Tampé, Robert; Bartholomäus, Patrick; Dietrich, Ursula; Dürr, Ralf

    2014-05-30

    HIV-1 is decorated with trimeric glycoprotein spikes that enable infection by engaging CD4 and a chemokine coreceptor, either CCR5 or CXCR4. The variable loop 3 (V3) of the HIV-1 envelope protein (Env) is the main determinant for coreceptor usage. The predominant CCR5 using (R5) HIV-1 Env has been intensively studied in function and structure, whereas the trimeric architecture of the less frequent, but more cytopathic CXCR4 using (X4) HIV-1 Env is largely unknown, as are the consequences of sequence changes in and near V3 on antigenicity and trimeric Env structure. Soluble trimeric gp140 Env constructs were used as immunogenic mimics of the native spikes to analyze their antigenic properties in the context of their overall 3D structure. We generated soluble, uncleaved, gp140 trimers from a prototypic T-cell line-adapted (TCLA) X4 HIV-1 strain (NL4-3) and a hybrid (NL4-3/ADA), in which the V3 spanning region was substituted with that from the primary R5 isolate ADA. Compared to an ADA (R5) gp140, the NL4-3 (X4) construct revealed an overall higher antibody accessibility, which was most pronounced for the CD4 binding site (CD4bs), but also observed for mAbs against CD4 induced (CD4i) epitopes and gp41 mAbs. V3 mAbs showed significant binding differences to the three constructs, which were refined by SPR analysis. Of interest, the NL4-3/ADA construct with the hybrid NL4-3/ADA CD4bs showed impaired CD4 and CD4bs mAb reactivity despite the presence of the essential elements of the CD4bs epitope. We obtained 3D reconstructions of the NL4-3 and the NL4-3/ADA gp140 trimers via electron microscopy and single particle analysis, which indicates that both constructs inherit a propeller-like architecture. The first 3D reconstruction of an Env construct from an X4 TCLA HIV-1 strain reveals an open conformation, in contrast to recently published more closed structures from R5 Env. Exchanging the X4 V3 spanning region for that of R5 ADA did not alter the open Env architecture as

  16. Metal-semiconductor, composite radiation detectors

    International Nuclear Information System (INIS)

    Orvis, W.J.; Yee, J.H.; Fuess, D.

    1992-12-01

    In 1989, Naruse and Hatayama of Toshiba published a design for an increased efficiency x-ray detector. The design increased the efficiency of a semiconductor detector by interspersing layers of high-z metal within it. Semiconductors such as silicon make good, high-resolution radiation detectors, but they have low efficiency because they are low-z materials (z = 14). High-z metals, on the other hand, are good absorbers of high-energy photons. By interspersing high-z metal layers with semiconductor layers, Naruse and Hatayama combined the high absorption efficiency of the high-z metals with the good detection capabilities of a semiconductor. This project is an attempt to use the same design to produce a high-efficiency, room temperature gamma ray detector. By their nature, gamma rays require thicker metal layers to efficiently absorb them. These thicker layers change the behavior of the detector by reducing the resolution, compared to a solid state detector, and shifting the photopeak by a predictable amount. During the last year, the authors have procured and tested a commercial device with operating characteristics similar to those of a single layer of the composite device. They have modeled the radiation transport in a multi-layered device, to verify the initial calculations of layer thickness and composition. They have modeled the electrostatic field in different device designs to locate and remove high-field regions that can cause device breakdown. They have fabricated 14 single layer prototypes

  17. Lightweight Hybrid Ablator Incorporating Aerogel-Filled Open-Cell Foam Structural Insulator, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — In previous work for NASA and DoD, Ultramet developed lightweight open-cell foam insulators composed of a carbon or ceramic structural foam skeleton filled with a...

  18. Hybrid Element Method for Compsoite Structures Subjected to Boundary Layer Loading Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In many situations, aerospace structures are subjected to a wide frequency spectrum of mechanical and/or acoustic excitations and therefore, there is a need for the...

  19. Lightweight Hybrid Ablator Incorporating Aerogel-Filled Open-Cell Foam Structural Insulator, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — In previous work for NASA and DoD, Ultramet developed lightweight open-cell foam insulators composed of a carbon or ceramic structural foam skeleton filled with a...

  20. Omnidirectional excitation of sidewall gap-plasmons in a hybrid gold-nanoparticle/aluminum-nanopore structure

    Directory of Open Access Journals (Sweden)

    Chatdanai Lumdee

    2016-06-01

    Full Text Available The gap-plasmon resonance of a gold nanoparticle inside a nanopore in an aluminum film is investigated in polarization dependent single particle microscopy and spectroscopy. Scattering and transmission measurements reveal that gap-plasmons of this structure can be excited and observed under normal incidence excitation and collection, in contrast to the more common particle-on-a-mirror structure. Correlation of numerical simulations with optical spectroscopy suggests that a local electric field enhancement factor in excess of 50 is achieved under normal incidence excitation, with a hot-spot located near the top surface of the structure. It is shown that the strong field enhancement from this sidewall gap-plasmon mode can be efficiently excited over a broad angular range. The presented plasmonic structure lends itself to implementation in low-cost, chemically stable, easily addressable biochemical sensor arrays providing large optical field enhancement factors.

  1. Structural and functional small animal imaging using hybrid-focus optoacoustic biomicroscopy

    Science.gov (United States)

    Rebling, Johannes; Estrada, Héctor; Gottschalk, Sven; Razansky, Daniel

    2017-07-01

    We present an optoacoustic microscope, combining structural and functional opticalresolution optoacoustic and ultrasound pulse-echo imaging. The system was applied to image Zebrafish larvae and complex vascular networks in the murine brain and ear.

  2. Mesoporous and carbon hybrid structures from layered molecular precursors for Li-ion battery application: the case of β-In2S3.

    Science.gov (United States)

    Zhang, Ming-Jian; Tian, Lei-Lei; Li, Shuankui; Lin, Ling-Piao; Pan, Feng

    2016-04-04

    A new method was demonstrated to construct mesoporous and carbon hybrid structures of β-In2S3 from the thermal decomposition of layered molecular precursors. When applied to LIBs, they all exhibit good cycling stability and excellent rate performance due to the great uniformity of mesopores and pyrolysis carbon distributed in the materials.

  3. Fine-scale temporal and spatial variation of taxon and clonal structure in the Daphnia longispina hybrid complex in heterogeneous environments

    Czech Academy of Sciences Publication Activity Database

    Yin, M.; Petrusek, A.; Seďa, Jaromír; Wolinska, J.

    2012-01-01

    Roč. 12, January (2012), s. 1-12 ISSN 1471-2148 R&D Projects: GA AV ČR(CZ) IAA600960901 Institutional support: RVO:60077344 Keywords : species complex * genetic-structure * interspecific hybridization * cyclic parthenogenesis * population-dynamics Subject RIV: EG - Zoology Impact factor: 3.285, year: 2012

  4. Structural archetypes in nickel(II) hybrid vanadates. Towards a directed hydrothermal synthesis

    International Nuclear Information System (INIS)

    Luis, R. Fernandez de; Urtiaga, M.K.; Mesa, J.L.; Rojo, T.; Arriortua, M.I.

    2009-01-01

    In the present work, we relate the modifications of the initial synthesis parameters (pH value, stoichiometry and concentration) with the different structural archetypes obtained in the {Ni/Bpy/VO} and {Ni/Bpe/VO} systems (4,4'-bipyridine (Bpy), 1,2-di(4-pyridyl) ethylene (Bpe)). The vanadium coordination is partially controlled by the hydrothermal synthesis conditions, and the final crystal structures depend on the synergetic interaction between the metal-organic subnets and the vanadium oxide subunits.

  5. Hybrid Mixed Media Nonwovens: An Investigation of Structure-Property Relationships

    Science.gov (United States)

    Hollowell, Kendall Birckhead

    There have been myriad studies on utilizing bicomponent splittables produced through spunbond/spunlace processes. These production methods have proven to yield microfibers which increase the surface area of the nonwoven structures. There has been recent focus on studying the microfibers within these nonwoven structures as well as using a multiplicity of deniers of fibers within the nonwoven. There have also been studies on producing nonwovens with fibers of differing cross-sectional shapes and diameters. The purpose of this study is to examine the properties of a nonwoven structure, marrying the concepts of multi-denier fibers with multi-shaped fibers in two configurations: three-layer and alternating. The basis for this study will be US Patent 6,964,931 B2 "Method of making Continuous Filament Web with Statistical Filament Distribution" as well as US Patent 7,981,336 B2 "Process of Making Mixed Fibers and Nonwoven Fabrics". This study addresses the melt-spinning and hydroentanglement of nonwoven webs made from bicomponent fibers in three-layer and alternating configurations. The bicomponent cross-sections that will be used include 16-segmented pie and 7-islands-in-the-sea. In this study the establishment of the utility of mixed media nonwovens will take place through property and structure analysis in order to determine the inherent properties of the mixed media structures as well as the structure-property relationships of the nonwoven fabric. Property and structure analysis will also take place on mixed media structures containing poly(lactic acid) as a sacrificial component in the bicomponent fiber after optimizing the removal conditions of the poly(lactic acid) in a sodium hydroxide (NaOH) bath.

  6. Structural characterization, AC conductivity, optical properties and biochemical study of a new hybrid phosphate: Scavenger of free radicals

    Science.gov (United States)

    Fezai, Ramzi; Hemissi, Hanene; Mezni, Ali; Rzaigui, Mohamed

    2017-12-01

    Single crystal of the hybrid compound [p-(F)C6H4NH3]6P6O18·2H2O has been grown with sizes up to 0.65 × 0.45 × 0.3 mm3 by the slow evaporation method. The crystal structure of this material was determined by single crystal X-ray diffraction. It crystallizes in the triclinic space group P 1 bar with the lattice parameters a = 10.16(3) Å, b = 15.87(3) Å, c = 16.36(4) Å, α = 80.93(2)°, β = 85.92(18)°, γ = 85.31(2)°, V = 2591.1(12) Å3 and Z = 2. Its crystal structure is a packing of alternated inorganic and organic layers parallel to (a, c) planes. The cohesion of the structure is essentially ensured by a hydrogen bonding network as well as electrostatic and Van Der Waals interactions and also F…F interactions so as to increase the stability of the 3D-network. The effect of the nature of the substituent in para-position with respect to amine group on obtained structures and on other studied properties was discussed. Crystal symmetry is confirmed by 31P MAS-NMR. Furthermore, IR characteristics and thermal analysis are given. The luminescent properties of this material have been carried out at room temperature based on UV absorption spectroscopy data. AC conductivity of this compound has been investigated by means of impedance spectroscopy measurements in the 303-383 K temperature range. The antioxidant study was determined, in vitro, using 1,1-diphenyl-2-picrylhydrazyl (DPPH), hydroxyl radical and reducing power and with ascorbic acid as a control. X-rays structural results are correlated with electrical and antioxidant findings.

  7. Combining Low Temperature Fluorescence DNA-Hybridization, Immunostaining, and Super-Resolution Localization Microscopy for Nano-Structure Analysis of ALU Elements and Their Influence on Chromatin Structure.

    Science.gov (United States)

    Krufczik, Matthias; Sievers, Aaron; Hausmann, Annkathrin; Lee, Jin-Ho; Hildenbrand, Georg; Schaufler, Wladimir; Hausmann, Michael

    2017-05-07

    Immunostaining and fluorescence in situ hybridization (FISH) are well established methods for specific labelling of chromatin in the cell nucleus. COMBO-FISH (combinatorial oligonucleotide fluorescence in situ hybridization) is a FISH method using computer designed oligonucleotide probes specifically co-localizing at given target sites. In combination with super resolution microscopy which achieves spatial resolution far beyond the Abbe Limit, it allows new insights into the nano-scaled structure and organization of the chromatin of the nucleus. To avoid nano-structural changes of the chromatin, the COMBO-FISH labelling protocol was optimized omitting heat treatment for denaturation of the target. As an example, this protocol was applied to ALU elements-dispersed short stretches of DNA which appear in different kinds in large numbers in primate genomes. These ALU elements seem to be involved in gene regulation, genomic diversity, disease induction, DNA repair, etc. By computer search, we developed a unique COMBO-FISH probe which specifically binds to ALU consensus elements and combined this DNA-DNA labelling procedure with heterochromatin immunostainings in formaldehyde-fixed cell specimens. By localization microscopy, the chromatin network-like arrangements of ALU oligonucleotide repeats and heterochromatin antibody labelling sites were simultaneously visualized and quantified. This novel approach which simultaneously combines COMBO-FISH and immunostaining was applied to chromatin analysis on the nanoscale after low-linear-energy-transfer (LET) radiation exposure at different doses. Dose-correlated curves were obtained from the amount of ALU representing signals, and the chromatin re-arrangements during DNA repair after irradiation were quantitatively studied on the nano-scale. Beyond applications in radiation research, the labelling strategy of immunostaining and COMBO-FISH with localization microscopy will also offer new potentials for analyses of subcellular

  8. Electrochemical H2O2biosensor composed of myoglobin on MoS2nanoparticle-graphene oxide hybrid structure.

    Science.gov (United States)

    Yoon, Jinho; Lee, Taek; Bapurao G, Bharate; Jo, Jinhee; Oh, Byung-Keun; Choi, Jeong-Woo

    2017-07-15

    In this research, the electrochemical biosensor composed of myoglobin (Mb) on molybdenum disulfide nanoparticles (MoS 2 NP) encapsulated with graphene oxide (GO) was fabricated for the detection of hydrogen peroxide (H 2 O 2 ). Hybrid structure composed of MoS 2 NP and GO (GO@MoS 2 ) was fabricated for the first time to enhance the electrochemical signal of the biosensor. As a sensing material, Mb was introduced to fabricate the biosensor for H 2 O 2 detection. Formation and immobilization of GO@MoS 2 was confirmed by transmission electron microscopy, ultraviolet-visible spectroscopy, scanning electron microscopy, and scanning tunneling microscopy. Immobilization of Mb, and electrochemical property of biosensor were investigated by cyclic voltammetry and amperometric i-t measurements. Fabricated biosensor showed the electrochemical signal enhanced redox current as -1.86μA at an oxidation potential and 1.95μA at a reduction potential that were enhanced relative to those of electrode prepared without GO@MoS 2 . Also, this biosensor showed the reproducibility of electrochemical signal, and retained the property until 9 days from fabrication. Upon addition of H 2 O 2 , the biosensor showed enhanced amperometric response current with selectivity relative to that of the biosensor prepared without GO@MoS 2 . This novel hybrid material-based biosensor can suggest a milestone in the development of a highly sensitive detecting platform for biosensor fabrication with highly sensitive detection of target molecules other than H 2 O 2 . Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Phase-separated structures of mixed Langmuir-Blodgett films of fatty acid and hybrid carboxylic acid.

    Science.gov (United States)

    Kimura, Hideto; Watanabe, Satoshi; Shibata, Hirobumi; Azumi, Reiko; Sakai, Hideki; Abe, Masahiko; Matsumoto, Mutsuyoshi

    2008-12-04

    Phase separation often occurs in mixed Langmuir-Blodgett (LB) films. Usually circular domains at the micrometer length scale form in the LB films. The size and shape of the domains are governed by a compromise between two competing interactions of line tension and dipole-dipole interaction. An attempt was made to control the line tension by varying systematically the hydrophobic moieties of the film-forming molecules. Phase-separated structures of two-component mixed LB films of fatty acid [C(k)H(2k+1)COOH (HkA)] and hybrid carboxylic acid [C(m)F(2m+1)C(n)H(2n)COOH (FmHnA)] were investigated. IR spectra of the mixed LB films of H17A and F8H10A revealed that the alkyl chains were in an all-trans conformation and that the molecular orientation remained unchanged when the two components were mixed. Nanowires formed in the mixed LB films of HkA and F8H10A. The width of the nanowires increased with an increase in k. Domain size and shape in the mixed LB films of H17A and FmHnA depended strongly on the values of m and n. Circular domains at the micrometer length scale formed in the region m + n or = 16 except for F6H10A. These results were explained by using a lattice model that considers the effect of the hydrophobic moieties of fatty acid and hybrid carboxylic acid on the line tension.

  10. Jovian Plasmas Torus Interaction with Europa. Plasma Wake Structure and Effect of Inductive Magnetic Field: 3D Hybrid Kinetic Simulation

    Science.gov (United States)

    Lipatov, A. S.; Cooper, J F.; Paterson, W. R.; Sittler, E. C., Jr.; Hartle, R. E.; Simpson, David G.

    2013-01-01

    The hybrid kinetic model supports comprehensive simulation of the interaction between different spatial and energetic elements of the Europa moon-magnetosphere system with respect to a variable upstream magnetic field and flux or density distributions of plasma and energetic ions, electrons, and neutral atoms. This capability is critical for improving the interpretation of the existing Europa flyby measurements from the Galileo Orbiter mission, and for planning flyby and orbital measurements (including the surface and atmospheric compositions) for future missions. The simulations are based on recent models of the atmosphere of Europa (Cassidy et al., 2007; Shematovich et al., 2005). In contrast to previous approaches with MHD simulations, the hybrid model allows us to fully take into account the finite gyroradius effect and electron pressure, and to correctly estimate the ion velocity distribution and the fluxes along the magnetic field (assuming an initial Maxwellian velocity distribution for upstream background ions). Photoionization, electron-impact ionization, charge exchange and collisions between the ions and neutrals are also included in our model. We consider the models with Oþ þ and Sþ þ background plasma, and various betas for background ions and electrons, and pickup electrons. The majority of O2 atmosphere is thermal with an extended non-thermal population (Cassidy et al., 2007). In this paper, we discuss two tasks: (1) the plasma wake structure dependence on the parameters of the upstream plasma and Europa's atmosphere (model I, cases (a) and (b) with a homogeneous Jovian magnetosphere field, an inductive magnetic dipole and high oceanic shell conductivity); and (2) estimation of the possible effect of an induced magnetic field arising from oceanic shell conductivity. This effect was estimated based on the difference between the observed and modeled magnetic fields (model II, case (c) with an inhomogeneous Jovian magnetosphere field, an inductive

  11. Rhombohedrel Hybrid Crystal Semiconductor Device

    Data.gov (United States)

    National Aeronautics and Space Administration — Development of a new high speed and high efficiency hybrid crystal structure semiconductor device based on the the recent invention of rhombohedral hybrid crystal...

  12. Integration of plug-in hybrid cars for the encouragement of intelligent power distribution structures; Integration von Plug-in-Hybrid Cars zur Foerderung intelligenter Verteilnetzstrukturen. Vorstudie

    Energy Technology Data Exchange (ETDEWEB)

    Horbaty, R.; Rigassi, R.

    2007-11-15

    This preliminary study for the Swiss Federal Office of Energy (SFOE) takes a look at how plug-in hybrid cars could be used to support the electricity supply in Switzerland. This study explains to what extent hybrid cars would be in a position to provide the services needed to regulate the Swiss electricity mains. Core elements of the concept known as 'Vehicle to Grid' (V2G) are presented. The requirements placed on the cars' equipment, including reversible battery chargers and communication equipment, are reviewed. Mains regulation systems are discussed, as are battery storage and the potential advantages offered by such a system. Challenges and hindrances to implementation are examined and initial feasibility studies are analysed. Questions still to be addressed are noted. A comprehensive appendix rounds off the report.

  13. Fuel Consumption Reduction By Use Of Hybrid Drive Systems

    OpenAIRE

    Renken, Folker

    2015-01-01

    Vehicles with hybrid drive systems are characterized by their driving dynamics, their energy efficiency and their environment-friendliness especially. Dependent on the electrical power and the drive train structure these hybrid drives are grouped into different classes. Designations such as micro-hybrid, mild- hybrid, full-hybrid, serial-hybrid, serial/parallel-hybrid or power-split-hybrid reflect the large variance of these different drive train possibilities. In hybrid drive systems electro...

  14. Structural archetypes in nickel(II) hybrid vanadates. Towards a directed hydrothermal synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Luis, R. Fernandez de; Urtiaga, M.K. [Dpto. Mineralogia y Petrologia, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco/UPV/EHU, Apdo. 644, 48080 Bilbao (Spain); Mesa, J.L.; Rojo, T. [Dpto. Quimica Inorganica, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco UPV/EHU, Apdo. 644, 48080 Bilbao (Spain); Arriortua, M.I. [Dpto. Mineralogia y Petrologia, Facultad de Ciencia y Tecnologia, Universidad del Pais Vasco/UPV/EHU, Apdo. 644, 48080 Bilbao (Spain)], E-mail: maribel.arriortua@ehu.es

    2009-07-01

    In the present work, we relate the modifications of the initial synthesis parameters (pH value, stoichiometry and concentration) with the different structural archetypes obtained in the {l_brace}Ni/Bpy/VO{r_brace} and {l_brace}Ni/Bpe/VO{r_brace} systems (4,4'-bipyridine (Bpy), 1,2-di(4-pyridyl) ethylene (Bpe)). The vanadium coordination is partially controlled by the hydrothermal synthesis conditions, and the final crystal structures depend on the synergetic interaction between the metal-organic subnets and the vanadium oxide subunits.

  15. Mesotubular-Structured Hybrid Membrane Nanocontainer for Periodical Monitoring, Separation, and Recovery of Cobalt Ions from Water.

    Science.gov (United States)

    El-Safty, Sherif A; Sakai, Masaru; Selim, Mahmoud M; Alhamid, Abdulaziz A

    2015-09-01

    Exposure to toxins can cause deleterious effects even at very low concentrations. We have developed an optical sensor, filter, and extractor (i.e., containerlike) in a nanoscale membrane (NSM) for the ultratrace sensing, separation, and recovery of Co(2+) ions from water. The design of the NSM is successfully controlled by dense decoration of a hydrophobic oil-hydrophilic receptor onto mesoscale tubular-structured silica nanochannels made of a hybrid anodic alumina membrane. The particular structure of the nanocontainer is ideal to control the multiple functions of the membrane, such as the optical detection/recognition, rejection/permeation, and recovery of Co(2+) species in a single step. A typical sensor, filter, and extractor assessment experiment was performed by using a benchtop contact time technique and a flow-through cell detector to allow for precise control of the optical detection and exclusive rejection of target ions and the permeation of nontarget metal ions in water. This nanocontainer membrane has great potential to meet the increasing needs of purification and separation of Co(2+) ions. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. A Structurally Simplified Hybrid Model of Genetic Algorithm and Support Vector Machine for Prediction of Chlorophyll a in Reservoirs

    Directory of Open Access Journals (Sweden)

    Jieqiong Su

    2015-04-01

    Full Text Available With decreasing water availability as a result of climate change and human activities, analysis of the influential factors and variation trends of chlorophyll a has become important to prevent reservoir eutrophication and ensure water supply safety. In this paper, a structurally simplified hybrid model of the genetic algorithm (GA and the support vector machine (SVM was developed for the prediction of monthly concentration of chlorophyll a in the Miyun Reservoir of northern China over the period from 2000 to 2010. Based on the influence factor analysis, the four most relevant influence factors of chlorophyll a (i.e., total phosphorus, total nitrogen, permanganate index, and reservoir storage were extracted using the method of feature selection with the GA, which simplified the model structure, making it more practical and efficient for environmental management. The results showed that the developed simplified GA-SVM model could solve nonlinear problems of complex system, and was suitable for the simulation and prediction of chlorophyll a with better performance in accuracy and efficiency in the Miyun Reservoir.

  17. Interface and photoluminescence characteristics of graphene-(GaN/InGaN)n multiple quantum wells hybrid structure

    International Nuclear Information System (INIS)

    Wang, Liancheng; Liu, Zhiqiang; Tian, Ying Dong; Yi, Xiaoyan; Wang, Junxi; Li, Jinmin; Wang, Guohong; Zhang, Zi-Hui

    2016-01-01

    The effects of graphene on the optical properties of active system, e.g., the InGaN/GaN multiple quantum wells, are thoroughly investigated and clarified. Here, we have investigated the mechanisms accounting for the photoluminescence reduction for the graphene covered GaN/InGaN multiple quantum wells hybrid structure. Compared to the bare multiple quantum wells, the photoluminescence intensity of graphene covered multiple quantum wells showed a 39% decrease after excluding the graphene absorption losses. The responsible mechanisms have been identified with the following factors: (1) the graphene two dimensional hole gas intensifies the polarization field in multiple quantum wells, thus steepening the quantum well band profile and causing hole-electron pairs to further separate; (2) a lower affinity of graphene compared to air leading to a weaker capability to confine the excited hot electrons in multiple quantum wells; and (3) exciton transfer through non-radiative energy transfer process. These factors are theoretically analysed based on advanced physical models of semiconductor devices calculations and experimentally verified by varying structural parameters, such as the indium fraction in multiple quantum wells and the thickness of the last GaN quantum barrier spacer layer.

  18. Interface and photoluminescence characteristics of graphene-(GaN/InGaN){sub n} multiple quantum wells hybrid structure

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Liancheng, E-mail: wanglc@semi.ac.cn, E-mail: lzq@semi.ac.cn, E-mail: zh.zhang@hebut.edu.cn [Engineering Product Development Pillar (EPD), Singapore University of Technology & Design (SUTD), 8 Somapah Road, Singapore 487372 (Singapore); Semiconductor Lighting Technology Research and Development Center, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Mind Star (Beijing) Technology Co., Ltd., Zhongguancun South Street, Haidian District, No. 45 Hing Fat Building 1001, Beijing 100872 (China); Liu, Zhiqiang, E-mail: wanglc@semi.ac.cn, E-mail: lzq@semi.ac.cn, E-mail: zh.zhang@hebut.edu.cn; Tian, Ying Dong; Yi, Xiaoyan; Wang, Junxi; Li, Jinmin; Wang, Guohong [Semiconductor Lighting Technology Research and Development Center, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Zhang, Zi-Hui, E-mail: wanglc@semi.ac.cn, E-mail: lzq@semi.ac.cn, E-mail: zh.zhang@hebut.edu.cn [Key Laboratory of Electronic Materials and Devices of Tianjin, School of Electronics and Information Engineering, Hebei University of Technology, Tianjin 300401 (China)

    2016-04-14

    The effects of graphene on the optical properties of active system, e.g., the InGaN/GaN multiple quantum wells, are thoroughly investigated and clarified. Here, we have investigated the mechanisms accounting for the photoluminescence reduction for the graphene covered GaN/InGaN multiple quantum wells hybrid structure. Compared to the bare multiple quantum wells, the photoluminescence intensity of graphene covered multiple quantum wells showed a 39% decrease after excluding the graphene absorption losses. The responsible mechanisms have been identified with the following factors: (1) the graphene two dimensional hole gas intensifies the polarization field in multiple quantum wells, thus steepening the quantum well band profile and causing hole-electron pairs to further separate; (2) a lower affinity of graphene compared to air leading to a weaker capability to confine the excited hot electrons in multiple quantum wells; and (3) exciton transfer through non-radiative energy transfer process. These factors are theoretically analysed based on advanced physical models of semiconductor devices calculations and experimentally verified by varying structural parameters, such as the indium fraction in multiple quantum wells and the thickness of the last GaN quantum barrier spacer layer.

  19. Application of the Hybrid Simulation Method for the Full-Scale Precast Reinforced Concrete Shear Wall Structure

    Directory of Open Access Journals (Sweden)

    Zaixian Chen

    2018-02-01

    Full Text Available The hybrid simulation (HS testing method combines physical test and numerical simulation, and provides a viable alternative to evaluate the structural seismic performance. Most studies focused on the accuracy, stability and reliability of the HS method in the small-scale tests. It is a challenge to evaluate the seismic performance of a twelve-story pre-cast reinforced concrete shear-wall structure using this HS method which takes the full-scale bottom three-story structural model as the physical substructure and the elastic non-linear model as the numerical substructure. This paper employs an equivalent force control (EFC method with implicit integration algorithm to deal with the numerical integration of the equation of motion (EOM and the control of the loading device. Because of the arrangement of the test model, an elastic non-linear numerical model is used to simulate the numerical substructure. And non-subdivision strategy for the displacement inflection point of numerical substructure is used to easily realize the simulation of the numerical substructure and thus reduce the measured error. The parameters of the EFC method are calculated basing on analytical and numerical studies and used to the actual full-scale HS test. Finally, the accuracy and feasibility of the EFC-based HS method is verified experimentally through the substructure HS tests of the pre-cast reinforced concrete shear-wall structure model. And the testing results of the descending stage can be conveniently obtained from the EFC-based HS method.

  20. Enhanced moisture-barrier property and flexibility of zirconium oxide/polymer hybrid structures

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Se Hee; Seo, Seung-Woo; Jung, Eun; Chae, Heeyeop; Cho, Sung Min [Sungkyunkwan University, Suwon (Korea, Republic of)

    2016-03-15

    New zirconium oxide (ZrO{sub 2})-based organic-inorganic multilayers were fabricated and tested for flexible moisture barriers and compared with typical aluminum oxide (Al{sub 2}O{sub 3})-based multilayers. We report that amorphous ZrO{sub 2} had a better intrinsic barrier property than that of amorphous Al{sub 2}O{sub 3}. Due to the lower elastic modulus of ZrO{sub 2}, the ZrO{sub 2}-based structures had better flexibility than that of the Al{sub 2}O{sub 3}-based structures. The ZrO{sub 2}-based barrier was superior to the Al{sub 2}O{sub 3}-based barrier not only for flexibility but also for barrier performance. The barrier property and flexibility of the ZrO{sub 2}-based structures were enhanced by about 20% and 30% over those of the Al{sub 2}O{sub 3}-based structures, respectively.

  1. A hybrid method for damage detection and quantification in advanced X-COR composite structures

    Science.gov (United States)

    Neerukatti, Rajesh Kumar; Rajadas, Abhishek; Borkowski, Luke; Chattopadhyay, Aditi; Huff, Daniel W.

    2016-04-01

    Advanced composite structures, such as foam core carbon fiber reinforced polymer composites, are increasingly being used in applications which require high strength, high in-plane and flexural stiffness, and low weight. However, the presence of in situ damage due to manufacturing defects and/or service conditions can complicate the failure mechanisms and compromise their strength and reliability. In this paper, the capability of detecting damages such as delaminations and foam-core separations in X-COR composite structures using non-destructive evaluation (NDE) and structural health monitoring (SHM) techniques is investigated. Two NDE techniques, flash thermography and low frequency ultrasonics, were used to detect and quantify the damage size and locations. Macro fiber composites (MFCs) were used as actuators and sensors to study the interaction of Lamb waves with delaminations and foam-core separations. The results indicate that both flash thermography and low frequency ultrasonics were capable of detecting damage in X-COR sandwich structures, although low frequency ultrasonic methods were capable of detecting through thickness damages more accurately than flash thermography. It was also observed that the presence of foam-core separations significantly changes the wave behavior when compared to delamination, which complicates the use of wave based SHM techniques. Further, a wave propagation model was developed to model the wave interaction with damages at different locations on the X-COR sandwich plate.

  2. Structuring a Clinical Learning Environment for a Hybrid-PBL Dental Curriculum.

    Science.gov (United States)

    MacNeil, M. A. J.; Walton, Joanne N.; Clark, D. Christopher; Tobias, David L.; Harrison, Rosamund L.

    1998-01-01

    Describes the evolution and implementation of a joint medical-dental problem-based learning (PBL) curriculum at the University of British Columbia's medical and dental schools, featuring development of an integrated care clinic. Issues in structuring the new curriculum are discussed, including management of the clinic's group practices, affective…

  3. Thickness Dependent Properties in Oxide Heterostructures Driven by Structurally Induced Metal–Oxygen Hybridization Variations

    NARCIS (Netherlands)

    Liao, Zhaoliang; Gauquelin, N.; Green, R.J.; Macke, S.; Gonissen, J.; Thomas, S.; Zhong, Z.; Li, Lin; Si, L.; van Aert, S.; Hansmann, P.; Held, K.; Xia, J.; Verbeeck, J.; van Tendeloo, G.; Sawatzky, G.A.; Koster, Gertjan; Huijben, Mark; Rijnders, Augustinus J.H.M.

    2017-01-01

    Thickness-driven electronic phase transitions are broadly observed in different types of functional perovskite heterostructures. However, uncertainty remains whether these effects are solely due to spatial confinement, broken symmetry, or rather to a change of structure with varying film thickness.

  4. Evaluation of structural and mechanical properties of electrospun nano-micro hybrid of poly hydroxybutyrate-chitosan/silk scaffold for cartilage tissue engineering.

    Science.gov (United States)

    Karbasi, Saeed; Fekrat, Farnoosh; Semnani, Daryoush; Razavi, Shahnaz; Zargar, Elham Naghash

    2016-01-01

    One of the new methods of scaffold fabrication is a nano-micro hybrid structure in which the properties of the scaffold are improved by introducing nanometer and micrometer structures. This method could be suitable for scaffold designing if some features improve. In this study, electrospun nanofibers of 9% weight solution of poly (3-hydroxybutyrate) (P3HB) and a 15% weight of chitosan by trifluoroacetic acid were coated on both the surface of a silk knitted substrate in the optimum condition to improve the mechanical properties of scaffolds for cartilage tissue engineering application. These hybrid nano-micro fibrous scaffolds were characterized by structural and mechanical evaluation methods. Scanning electron microscopy values and porosity analysis showed that average diameter of nanofibers was 584.94 nm in electrospinning part and general porosity was more than 80%. Fourier transform infrared spectroscopy results indicated the presence of all elements without pollution. The tensile test also stated that by electrospinning, as well as adding chitosan, both maximum strength and maximum elongation increased to 187 N and 10 mm. It means that the microfibrous part of scaffold could affect mechanical properties of nano part of the hybrid scaffold, significantly. It could be concluded that P3HB-chitosan/silk hybrid scaffolds can be a good candidate for cartilage tissue engineering.

  5. Micromechanics of Amorphous Metal/Polymer Hybrid Structures with 3D Cellular Architectures: Size Effects, Buckling Behavior, and Energy Absorption Capability.

    Science.gov (United States)

    Mieszala, Maxime; Hasegawa, Madoka; Guillonneau, Gaylord; Bauer, Jens; Raghavan, Rejin; Frantz, Cédric; Kraft, Oliver; Mischler, Stefano; Michler, Johann; Philippe, Laetitia

    2017-02-01

    By designing advantageous cellular geometries and combining the material size effects at the nanometer scale, lightweight hybrid microarchitectured materials with tailored structural properties are achieved. Prior studies reported the mechanical properties of high strength cellular ceramic composites, obtained by atomic layer deposition. However, few studies have examined the properties of similar structures with metal coatings. To determine the mechanical performance of polymer cellular structures reinforced with a metal coating, 3D laser lithography and electroless deposition of an amorphous layer of nickel-boron (NiB) is used for the first time to produce metal/polymer hybrid structures. In this work, the mechanical response of microarchitectured structures is investigated with an emphasis on the effects of the architecture and the amorphous NiB thickness on their deformation mechanisms and energy absorption capability. Microcompression experiments show an enhancement of the mechanical properties with the NiB thickness, suggesting that the deformation mechanism and the buckling behavior are controlled by the brittle-to-ductile transition in the NiB layer. In addition, the energy absorption properties demonstrate the possibility of tuning the energy absorption efficiency with adequate designs. These findings suggest that microarchitectured metal/polymer hybrid structures are effective in producing materials with unique property combinations. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Determination of the structure, morphology and complex refractive index in ZnO-nanopencils/P3HT hybrid structures

    International Nuclear Information System (INIS)

    Motaung, David E.; Malgas, Gerald F.; Arendse, Christopher J.; Mavundla, Sipho E.

    2012-01-01

    Well crystallized flower-shaped ZnO-structures composed of a perfectly hexagonal-shaped ZnO structure were successfully synthesized using a simple microwave assisted hydrothermal method. The NPs with a hexagonal stem and a tapering tip grows out of the base of the flower-shapes. ZnO-NPs were incorporated into the nanomorphology of P3HT and two variations of P3HT:C 60 and P3HT:PCBM blended films in order to facilitate charge separation and transport. Thermo-gravimetric analysis revealed that ZnO-NPs are more stable and are of high purity. A complete PL quenching was demonstrated upon incorporating ZnO-NPs on the surface of P3HT and blended films indicating a charge transfer along the ZnO/P3HT and ZnO/P3HT:fullerenes induced by the aligned nanorods which are working as effective electron collectors by shortening the average electron diffusion distance in the P3HT and fullerenes network. Spectroscopic ellipsometry demonstrated that infiltrating of ZnO-NPs, results in the improved refractive index, extinction coefficient and shifts to lower photon energies. Such shifts can be inferred to the improved light absorption through the waveguide effect from the NPs and an increased interfacial area between the ZnO-NPs and P3HT. An improvement in the mobility and conductivity of P3HT films was observed with an incorporation of ZnO. -- Highlights: ► Flower-shaped ZnO-structures were synthesized via microwave hydrothermal method. ► ZnO-nanopencils were incorporated on the P3HT and blended surface. ► Formation of hexagonal and cone-like structures on the P3HT surface demonstrated an improved morphology. ► The interfacial area and charge transport improved. ► The absorption spectra, refractive index and extinction coefficient shifted to lower photon energies.

  7. Protein Tertiary Structure Prediction Based on Main Chain Angle Using a Hybrid Bees Colony Optimization Algorithm

    Science.gov (United States)

    Mahmood, Zakaria N.; Mahmuddin, Massudi; Mahmood, Mohammed Nooraldeen

    Encoding proteins of amino acid sequence to predict classified into their respective families and subfamilies is important research area. However for a given protein, knowing the exact action whether hormonal, enzymatic, transmembranal or nuclear receptors does not depend solely on amino acid sequence but on the way the amino acid thread folds as well. This study provides a prototype system that able to predict a protein tertiary structure. Several methods are used to develop and evaluate the system to produce better accuracy in protein 3D structure prediction. The Bees Optimization algorithm which inspired from the honey bees food foraging method, is used in the searching phase. In this study, the experiment is conducted on short sequence proteins that have been used by the previous researches using well-known tools. The proposed approach shows a promising result.

  8. Demonstration of Corrosion-Resistant Hybrid Composite Bridge Beams for Structural Applications

    Science.gov (United States)

    2016-09-01

    severity. Although the steel coupon testing resulted in a C2 classification , the results were on the upper limit of the category. The potential for...suggest the Fort Knox Bridge #4 site is a Category 3 classification of atmospheric corrosion severity. Although the steel coupon testing re- sulted in a...result of corrosion of the steel support structures or the reinforcing bar in the concrete. The application of corrosion-resistant technology can

  9. Structured nanoporous surfaces from hybrid block copolymer micelle films with metal ions.

    Science.gov (United States)

    Kim, Minsoo P; Kim, Hyeong Jun; Kim, Bumjoon J; Yi, Gi-Ra

    2015-03-06

    We present a novel method for producing structured nanoporous thin films using block copolymer (BCP) micelles loaded with metallic ions. The BCP micellar thin films containing gold (Au) ions were prepared by spin-coating poly(styrene-block-4-vinylpyridine) (PS-b-P4VP) micelle solutions in which Au precursors (AuCl4(-)) were selectively loaded onto the P4VP core. When the micellar films were exposed to cetyltrimethylammonium bromide (CTAB) solutions, the Au precursors were selectively extracted from the P4VP domains due to their strong electrostatic interaction with CTAB, leading to the formation of pores in the micelles. Consequently, regularly patterned nanoporous surfaces were formed. By controlling the molecular weight (Mn) of PS-b-P4VP and the amount of Au precursors (λ) that were loaded in the P4VP domains, the pore size and depth could be tuned precisely. In particular, when a sufficient amount of Au precursors was loaded (λ  ≥ 0.3), the porous surface nanostructure was well developed. In addition, the pore size and depth of the nanostructure increased as the λ value increased. For instance, when the λ value increased from 0.3 to 1.0, the pore size increased from 22.8 nm to 28.8 nm, and the pore depth increased from 2.1 nm to 3.2 nm. Interestingly, the transition from the nonporous structures to the porous structures in the micellar film could be reversibly controlled by adding and removing the Au precursors in the film. Moreover, our method for the preparation of nanoporous films can be extended to micellar film by incorporating other metal ions such as silver (Ag) and iron (Fe).

  10. Photovoltaic performance of hybrid ITO/PEDOT:PSS/n-SnS/Al solar cell structure

    Science.gov (United States)

    Jain, Priyal; Arun, P.

    2016-07-01

    The present paper discusses the performance of ITO/PEDOT:PSS/n-SnS/Al structured solar cells fabricated by thermal evaporation. The performance characterizing parameters such as the open circuit voltage, short circuit current density, series resistance, parallel resistance, ideality factor and the overall efficiency were found to be dependent on the SnS grain size in the nano-meter regime and incident light intensity. The experimental work directly reconfirms the theoretical results and ideas raised in the literature by early researchers.

  11. Perovskite-based solar cells with inorganic inverted hybrid planar heterojunction structure

    OpenAIRE

    Wei-Chih Lai; Kun-Wei Lin; Tzung-Fang Guo; Peter Chen; Yuan-Yu Liao

    2018-01-01

    We demonstrated the good performance of inorganic inverted CH3NH3PbI3 perovskite-based solar cells (SCs) with glass/ITO/NiOx/CH3NH3PbI3 perovskite/C60/ room temperature (RT)-sputtered ZnO/Al structure. We adopted spin coating and RT sputtering for the deposition of NiOx and ZnO, respectively. The inorganic hole and electron transport layer of NiOx and RT-sputtered ZnO, respectively, could improve the open-circuit voltage (VOC), short-circuit current density (JSC), and power conversion efficie...

  12. Identification of Persistent RNA-DNA Hybrid Structures within the Origin of Replication of Human Cytomegalovirus

    OpenAIRE

    Prichard, Mark N.; Jairath, Sanju; Penfold, Mark E. T.; Jeor, Stephen St.; Bohlman, Marlene C.; Pari, Gregory S.

    1998-01-01

    Human cytomegalovirus (HCMV) lytic-phase DNA replication initiates at the cis-acting origin of replication, oriLyt. oriLyt is a structurally complex region containing repeat elements and transcription factor binding sites. We identified two site-specific alkali-labile regions within oriLyt which flank an alkali-resistant DNA segment. These alkali-sensitive regions were the result of the degradation of two RNA species embedded within oriLyt and covalently linked to viral DNA. The virus-associa...

  13. Helicity-dependent all-optical switching in hybrid metal-ferromagnet structures for ultrafast magnetic data storage

    Science.gov (United States)

    Cheng, Feng

    The emerging Big Data era demands the rapidly increasing need for speed and capacity of storing and processing information. Standalone magnetic recording devices, such as hard disk drives (HDDs), have always been playing a central role in modern data storage and continuously advancing. Recognizing the growing capacity gap between the demand and production, industry has pushed the bit areal density in HDDs to 900 Giga-bit/square-inch, a remarkable 450-million-fold increase since the invention of the first hard disk drive in 1956. However, the further development of HDD capacity is facing a pressing challenge, the so-called superparamagnetic effect, that leads to the loss of information when a single bit becomes too small to preserve the magnetization. This requires new magnetic recording technologies that can write more stable magnetic bits into hard magnetic materials. Recent research has shown that it is possible to use ultrafast laser pulses to switch the magnetization in certain types of magnetic thin films. Surprisingly, such a process does not require an externally applied magnetic field that always exists in conventional HDDs. Furthermore, the optically induced magnetization switching is extremely fast, up to sub-picosecond (10 -12 s) level, while with traditional recording method the deterministic switching does not take place shorter than 20 ps. It's worth noting that the direction of magnetization is related to the helicity of the incident laser pulses. Namely, the right-handed polarized laser pulses will generate magnetization pointing in one direction while left-handed polarized laser pulses generate magnetization pointing in the other direction. This so-called helicity-dependent all-optical switching (HD-AOS) phenomenon can be potentially used in the next-generation of magnetic storage systems. In this thesis, I explore the HD-AOS phenomenon in hybrid metal-ferromagnet structures, which consist of gold and Co/Pt multilayers. The experiment results show

  14. Surface Electronic Structure of Hybrid Organo Lead Bromide Perovskite Single Crystals

    KAUST Repository

    Komesu, Takashi

    2016-08-24

    The electronic structure and band dispersion of methylammonium lead bromide, CH3NH3PbBr3, has been investigated through a combination of angle-resolved photoemission spectroscopy (ARPES) and inverse photoemission spectroscopy (IPES), as well as theoretical modeling based on density functional theory. The experimental band structures are consistent with the density functional calculations. The results demonstrate the presence of a dispersive valence band in MAPbBr3 that peaks at the M point of the surface Brillouin zone. The results also indicate that the surface termination of the CH3NH3PbBr3 is the methylammonium bromide (CH3NH3Br) layer. We find our results support models that predict a heavier hole effective mass in the region of -0.23 to -0.26 me, along the Γ (surface Brillouin center) to M point of the surface Brillouin zone. The surface appears to be n-type as a result of an excess of lead in the surface region. © 2016 American Chemical Society.

  15. Optimization of hybrid organic-inorganic interdigitated photovoltaic device structure using a 2D diffusion model.

    Science.gov (United States)

    Krali, Emiljana; Curry, Richard J

    2011-04-26

    To improve the efficiency of organic photovoltaic devices the inclusion of semiconducting nanoparticles such as PbS has been used to enhance near-infrared absorption. Additionally the use of interdigitated heterojunctions has been explored as a means of improving charge extraction. In this paper we provide a two-dimensional model taking into account these approaches with the aim of predicting an optimized device geometry to maximize the efficiency. The steady-state exciton population has been calculated in each of the active regions taking into account the full optical response based on using a finite difference approach to obtain approximate numerical solutions to the 2D exciton diffusion equation. On the basis of this we calculate the contribution of each active material to the device short circuit current and power conversion efficiency. We show that optimized structures can lead to power conversions efficiencies of ∼50% compared to a maximum of ∼17% for planar heterojunction devices. To achieve this the interdigitated region thickness should be ∼800 nm with PbS and C(60) widths of ∼60 and 20 nm, respectively. Even modest nanopatterning using much thinner active regions provides improvements in efficiency and may be approached using a variety of methods including nanoimprinting lithography, nanotemplating, or the incorporation of presynthesized nanorod structures.

  16. A Tb–Zn tetra(4-sulfonatophenyl)porphyrin hybrid: Preparation, structure, photophysical and electrochemical properties

    International Nuclear Information System (INIS)

    Chen, Wen-Tong; Hu, Rong-Hua; Wang, Yin-Feng; Zhang, Xian; Liu, Juan

    2014-01-01

    A terbium-zinc porphyrin, i.e. [TbZn(TPPS)H 3 O] n (1) (TPPS=tetra(4-sulfonatophenyl)porphyrin), has been obtained from a solvothermal reaction and structurally analyzed by single-crystal X-ray diffraction. Compound 1 is characteristic of a condensed three-dimensional (3-D) porous open framework with two types of infinite one-dimensional (1-D) chain-like structure. Compound 1 exhibits a void space of 215 Å 3 , which is 9.2% of the unit-cell volume. TG/DTA measurement reveals that the framework of compound 1 is thermally stable up to 336 °C. In order to reveal its photophysical and electrochemical properties, we investigated compound 1 in detail with UV–vis spectra, fluorescence, quantum yield, luminescence lifetime, and CV/DPV. - Graphical abstract: A terbium–zinc porphyrin [TbZn(TPPS)H 3 O] n has been obtained from a solvothermal reaction. It features a condensed 3-D porous open framework. It shows good thermal stability. - Highlights: • This paper reports a novel terbium–zinc porphyrin. • It features a novel condensed three-dimensional porous open framework. • The title compound is thermally stable up to 336 °C. • It is studied by UV–vis, fluorescence, quantum yield, lifetime, and CV/DPV

  17. Hybrid structure of polyaniline/ZnO nanograss and its application in dye-sensitized solar cell with performance improvement

    International Nuclear Information System (INIS)

    Zhu Shibu; Wei Wei; Chen Xiangnan; Jiang Man; Zhou Zuowan

    2012-01-01

    Polyaniline (PANI) hybridized ZnO photoanode for dye-sensitized solar cell (DSSC) was primarily prepared via a two-step process which involved hydrothermal growth of ZnO nanograss on the fluorine-doped tin oxide (FTO) substrate and subsequently chemisorption of PANI on the surfaces of the ZnO nanorods. The PANI hybridized ZnO nanograss films were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectra (FT-IR), and the results indicated that there were chemical interactions between PANI and ZnO. Both pure ZnO nanograss and PANI hybridized ZnO nanograss were applied to DSSC. The results of photoelectrochemical measurement showed that the photocurrent density of PANI (100 mg/L) hybridized ZnO nanograss photoanode was significantly enhanced, and the overall light-conversion efficiency increased by 60%. The electrochemical impedance spectra (EIS) displayed that the electron densities in photoanodes of PANI hybridized ZnO nanograss were larger than that in pure ZnO nanograss. This is ascribed to more effective charge separation and faster interfacial charge transferring occurred in the hybrid photoanode. - Graphical abstract: Operational principle of the DSSC: the introduced hybridizing PANI layer performs effective charge separation and faster interfacial charge transferring. Highlights: ► PANI/ZnO nanograss hybrid materials as photoanode in Dye-sensitized solar cell. ► Photoelectric conversion efficiency after hybridization was enhanced by 60%. ► PANI hybridizing ZnO nanograss induced a rapid charge separation.

  18. Check of hybrid structures and lightweight construction materials. Usage of 3D-CT

    International Nuclear Information System (INIS)

    Szepanski, Kamil David

    2015-01-01

    Lightweight structures and modern methods of generating samples require in most cases non-destructive-testing to verify their state. They often must not be destroyed for initial testing as they are unique and irreplaceable. So computed tomography serves well as the sample is not being touched or manipulated for the analysis. Meanwhile in-situ testing of stable stress situations, for example pressure and tension is available and gives insight where only the measured data were before. This allows the identification of seeds for failure. The production process can be recorded also within the sample and not only its surface. We demonstrate detectable defects in carbon reinforced plastic parts, laser sintered metal parts and an example for optimizing the process of printing a plastic part for function.

  19. Synthesis and structural characterization of piperazino-modified DNA that favours hybridization towards DNA over RNA

    DEFF Research Database (Denmark)

    Skov, Joan; Bryld, Torsten; Lindegaard, Dorthe

    2011-01-01

    We report the synthesis of two C4'-modified DNA analogues and characterize their structural impact on dsDNA duplexes. The 4'-C-piperazinomethyl modification stabilizes dsDNA by up to 5°C per incorporation. Extension of the modification with a butanoyl-linked pyrene increases the dsDNA stabilization...... to a maximum of 9°C per incorporation. Using fluorescence, ultraviolet and nuclear magnetic resonance (NMR) spectroscopy, we show that the stabilization is achieved by pyrene intercalation in the dsDNA duplex. The pyrene moiety is not restricted to one intercalation site but rather switches between multiple...... sites in intermediate exchange on the NMR timescale, resulting in broad lines in NMR spectra. We identified two intercalation sites with NOE data showing that the pyrene prefers to intercalate one base pair away from the modified nucleotide with its linker curled up in the minor groove. Both...

  20. Effects of B site doping on electronic structures of InNbO4 based on hybrid density functional calculations

    Science.gov (United States)

    Lu, M. F.; Zhou, C. P.; Li, Q. Q.; Zhang, C. L.; Shi, H. F.

    2018-01-01

    In order to improve the photocatalytic activity under visible-light irradiation, we adopted first principle calculations based on density functional theory (DFT) to calculate the electronic structures of B site transition metal element doped InNbO4. The results indicated that the complete hybridization of Nb 4d states and some Ti 3d states contributed to the new conduction band of Ti doped InNbO4, barely changing the position of band edge. For Cr doping, some localized Cr 3d states were introduced into the band gap. Nonetheless, the potential of localized levels was too positive to cause visible-light reaction. When it came to Cu doping, the band gap was almost same with that of InNbO4 as well as some localized Cu 3d states appeared above the top of VB. The introduction of localized energy levels benefited electrons to migrate from valence band (VB) to conduction band (CB) by absorbing lower energy photons, realizing visible-light response.

  1. Highly selective and active CO2 reduction electrocatalysts based on cobalt phthalocyanine/carbon nanotube hybrid structures

    Science.gov (United States)

    Zhang, Xing; Wu, Zishan; Zhang, Xiao; Li, Liewu; Li, Yanyan; Xu, Haomin; Li, Xiaoxiao; Yu, Xiaolu; Zhang, Zisheng; Liang, Yongye; Wang, Hailiang

    2017-03-01

    Electrochemical reduction of carbon dioxide with renewable energy is a sustainable way of producing carbon-neutral fuels. However, developing active, selective and stable electrocatalysts is challenging and entails material structure design and tailoring across a range of length scales. Here we report a cobalt-phthalocyanine-based high-performance carbon dioxide reduction electrocatalyst material developed with a combined nanoscale and molecular approach. On the nanoscale, cobalt phthalocyanine (CoPc) molecules are uniformly anchored on carbon nanotubes to afford substantially increased current density, improved selectivity for carbon monoxide, and enhanced durability. On the molecular level, the catalytic performance is further enhanced by introducing cyano groups to the CoPc molecule. The resulting hybrid catalyst exhibits >95% Faradaic efficiency for carbon monoxide production in a wide potential range and extraordinary catalytic activity with a current density of 15.0 mA cm-2 and a turnover frequency of 4.1 s-1 at the overpotential of 0.52 V in a near-neutral aqueous solution.

  2. Highly selective and active CO2 reduction electrocatalysts based on cobalt phthalocyanine/carbon nanotube hybrid structures

    Science.gov (United States)

    Zhang, Xing; Wu, Zishan; Zhang, Xiao; Li, Liewu; Li, Yanyan; Xu, Haomin; Li, Xiaoxiao; Yu, Xiaolu; Zhang, Zisheng; Liang, Yongye; Wang, Hailiang

    2017-01-01

    Electrochemical reduction of carbon dioxide with renewable energy is a sustainable way of producing carbon-neutral fuels. However, developing active, selective and stable electrocatalysts is challenging and entails material structure design and tailoring across a range of length scales. Here we report a cobalt-phthalocyanine-based high-performance carbon dioxide reduction electrocatalyst material developed with a combined nanoscale and molecular approach. On the nanoscale, cobalt phthalocyanine (CoPc) molecules are uniformly anchored on carbon nanotubes to afford substantially increased current density, improved selectivity for carbon monoxide, and enhanced durability. On the molecular level, the catalytic performance is further enhanced by introducing cyano groups to the CoPc molecule. The resulting hybrid catalyst exhibits >95% Faradaic efficiency for carbon monoxide production in a wide potential range and extraordinary catalytic activity with a current density of 15.0 mA cm−2 and a turnover frequency of 4.1 s−1 at the overpotential of 0.52 V in a near-neutral aqueous solution. PMID:28272403

  3. Interactive cellular proteins related to classical swine fever virus non-structure protein 2 by yeast two-hybrid analysis.

    Science.gov (United States)

    Kang, Kai; Guo, Kangkang; Tang, Qinhai; Zhang, Yanming; Wu, Jiang; Li, Weiwei; Lin, Zhi

    2012-12-01

    Classical swine fever is caused by the classical swine fever virus (CSFV), which has a special affinity to endothelial cells. This fever is characterized by hemorrhage and necrosis of vascular injury. Very little information is available on the interaction between vascular endothelial cells and CSFV. In the current report, the cDNA library of swine umbilical vein endothelial cell (SUVEC) was constructed by the switching mechanism at 5' end of the RNA transcript approach. The yeast two-hybrid (Y2H) system was adopted to screen non-structure 2 protein (NS2) interactive proteins in the SUVEC line. Alignment with the NCBI database revealed 11 interactive proteins: GOPC, HNRNPH1, DNAJA1, ATP6, CSDE1, CNDP2, FANCL, TMED4, DNAJA4, MOAP1, and PNMA1. These proteins were mostly related to apoptosis, stress response and oxidation reduction, or metabolism. In the protein interaction network constructed based on proteins with NS2, the more important proteins were MOAP1, DNAJA1, GOPC, FANCL, TMED4, and CSDE1. The interactions detected by the Y2H should be regarded only as preliminary indications. However, the CSFV NS2 interactive proteins in the SUVEC cDNA library obtained in the current study provides valuable information for gaining a better understanding of the host protein-virus interactions of the CSFV NS2 protein.

  4. Structure characterization, photoluminescence and dielectric properties of a new hybrid compound containing chlorate anions of zincate (II)

    Science.gov (United States)

    Lassoued, Mohamed Saber; Abdelbaky, Mohammed S. M.; Ben Soltan, Wissem; Lassoued, Abdelmajid; Ammar, Salah; Gadri, Abdellatif; Ben Salah, Abdelhamid; García-Granda, Santiago

    2018-04-01

    A new hybrid compound, bis (2-aminophenylenamonium) tetrachlorozincate (II), was synthesized and formulated as (C6H9N2)2ZnCl4. Its crystal structure was solved by single crystal X-ray diffraction reveling that compound crystallizes in the monoclinic system, space group C2/c (N°: 15) with cell parameters a = 7.4957(4) Å, b = 25.6837(15) Å, c = 9.4041(5) Å, β = 94.35(0)°, V = 1805.23(45) Å3. Their atomic arrangement can be described as an alternation of inorganic and organic layers, [ZnCl4]2- tetrahedral anions and 2-aminophenylenamonium cations. The cohesion of the atomic arrangement is ensured by hydrogen bonds (strong Nsbnd H⋯N and weak Nsbnd H⋯Cl) and π-π stacking interactions between identical antiparallel organic moieties. In optical transmission and photoluminescence measurements, this material exhibit two absorption bands (253 and 316 nm) and a strong emission line (390 nm), while the thermal analysis disclosed a phase transition at 420-445 K previously to the sample decomposition at 476 K. Finally, electrical measurements were performed to discuss the phase-transition mechanism.

  5. New hybrid magnet system for structure research at highest magnetic fields and temperatures in the millikelvin region

    International Nuclear Information System (INIS)

    Smeibidl, Peter; Ehmler, Hartmut; Tennant, Alan; Bird, Mark

    2012-01-01

    The Helmholtz Centre Berlin (HZB) is a user facility for the study of structure and dynamics with neutrons and synchrotron radiation with special emphasis on experiments under extreme conditions. Neutron scattering is uniquely suited to study magnetic properties on a microscopic length scale, because neutrons have comparable wavelengths and, due to their magnetic moment, they interact with the atomic magnetic moments. At HZB a dedicated instrument for neutron scattering at extreme magnetic fields and low temperatures is under construction, the Extreme Environment Diffractometer ExED. It is projected according to the time-of-flight principle for elastic and inelastic neutron scattering and for the special geometric constraints of analysing samples in a high field magnet. The new hybrid magnet will not only allow for novel experiments, it will be at the forefront of development in magnet technology itself. With a set of superconducting and resistive coils a maximum field above 30 T will be possible. To compromise between the needs of the magnet design for highest fields and the concept of the neutron instrument, the magnetic field will be generated by means of a coned, resistive inner solenoid and a superconducting outer solenoid with horizontal field orientation. To allow for experiments down to Millikelvin Temperatures the installation of a 3 He or a dilution cryostat with a closed cycle precooling stage is foreseen.

  6. Facile fabrication of nano-structured silica hybrid film with superhydrophobicity by one-step VAFS approach

    Science.gov (United States)

    Jia, Yi; Yue, Renliang; Liu, Gang; Yang, Jie; Ni, Yong; Wu, Xiaofeng; Chen, Yunfa

    2013-01-01

    Here we report a novel one-step vapor-fed aerosol flame synthesis (VAFS) method to attain silica hybrid film with superhydrophobicity on normal glass and other engineering material substrates using hexamethyldisiloxane (HMDSO) as precursor. The deposited nano-structured silica films represent excellent superhydrophobicity with contact angle larger than 150° and sliding angle below 5°, without any surface modification or other post treatments. SEM photographs proved that flame-made SiO2 nanoparticles formed dual-scale surface roughness on the substrates. It was confirmed by FTIR and XPS that the in situ formed organic fragments on the particle surface as species like (CH3)xSiO2-x/2 (x = 1, 2, 3) which progressively lowered the surface energy of fabricated films. Thus, these combined dual-scale roughness and lowered surface energy cooperatively produced superhydrophobic films. IR camera had been used to monitor the real-time flame temperature. It is found that the inert dilution gas inflow played a critical role in attaining superhydrophobicity due to its cooling and anti-oxidation effect. This method is facile and scalable for diverse substrates, without any requirement of complex equipments and multiple processing steps. It may contribute to the industrial fabrication of superhydrophobic films.

  7. Highly selective and active CO2reduction electrocatalysts based on cobalt phthalocyanine/carbon nanotube hybrid structures.

    Science.gov (United States)

    Zhang, Xing; Wu, Zishan; Zhang, Xiao; Li, Liewu; Li, Yanyan; Xu, Haomin; Li, Xiaoxiao; Yu, Xiaolu; Zhang, Zisheng; Liang, Yongye; Wang, Hailiang

    2017-03-08

    Electrochemical reduction of carbon dioxide with renewable energy is a sustainable way of producing carbon-neutral fuels. However, developing active, selective and stable electrocatalysts is challenging and entails material structure design and tailoring across a range of length scales. Here we report a cobalt-phthalocyanine-based high-performance carbon dioxide reduction electrocatalyst material developed with a combined nanoscale and molecular approach. On the nanoscale, cobalt phthalocyanine (CoPc) molecules are uniformly anchored on carbon nanotubes to afford substantially increased current density, improved selectivity for carbon monoxide, and enhanced durability. On the molecular level, the catalytic performance is further enhanced by introducing cyano groups to the CoPc molecule. The resulting hybrid catalyst exhibits >95% Faradaic efficiency for carbon monoxide production in a wide potential range and extraordinary catalytic activity with a current density of 15.0 mA cm -2 and a turnover frequency of 4.1 s -1 at the overpotential of 0.52 V in a near-neutral aqueous solution.

  8. Hierarchical Polyphosphazene@Molybdenum Disulfide Hybrid Structure for Enhancing the Flame Retardancy and Mechanical Property of Epoxy Resins.

    Science.gov (United States)

    Zhou, Xia; Qiu, Shuilai; Xing, Weiyi; Gangireddy, Chandra Sekhar Reddy; Gui, Zhou; Hu, Yuan

    2017-08-30

    A novel polyphosphazene (PZS) microsphere@molybdenum disulfide nanoflower (MoS 2 ) hierarchical hybrid architecture was first synthesized and applied for enhancing the mechanical performance and flame retardancy of epoxy (EP) resin via a cooperative effect. Herein, using PZS microsphere as the template, a layer of MoS 2 nanoflowers were anchored to PZS spheres via a hydrothermal strategy. The well-designed PZS@MoS 2 exhibits excellent fire retardancy and a reinforcing effect. The obtained PZS@MoS 2 significantly enhanced the flame-retardant performance of EP composites, which can be proved by thermogravimetric and cone calorimeter results. For instance, the incorporation of 3 wt % PZS@MoS 2 brought about a 41.3% maximum reduction in the peak heat-release rate and decreased by 30.3% maximum in the total heat release, accompanying the higher graphitized char layer. With regard to mechanical property, the storage modulus of EP/PZS@MoS 2 3.0 in the glassy state was dramatically increased to 22.4 GPa in comparison with that of pure EP (11.15 GPa). It is sensible to know that the improved flame-retardant performance for EP composites is primarily assigned to a physical barrier effect of the MoS 2 nanoflowers and the polyphosphazene structure has an positive impact on promoting char formation in the condensed phase.

  9. Hybrid Titanium/Biodegradable Polymer Implants with an Hierarchical Pore Structure as a Means to Control Selective Cell Movement

    Science.gov (United States)

    Vrana, Nihal Engin; Dupret, Agnès; Coraux, Christelle; Vautier, Dominique; Debry, Christian; Lavalle, Philippe

    2011-01-01

    In order to improve implant success rate, it is important to enhance their responsiveness to the prevailing conditions following implantation. Uncontrolled movement of inflammatory cells and fibroblasts is one of these in vivo problems and the porosity properties of the implant have a strong effect on these. Here, we describe a hybrid system composed of a macroporous titanium structure filled with a microporous biodegradable polymer. This polymer matrix has a distinct porosity gradient to accommodate different cell types (fibroblasts and epithelial cells). The main clinical application of this system will be the prevention of restenosis due to excessive fibroblast migration and proliferation in the case of tracheal implants. Methodology/Principal Findings A microbead-based titanium template was filled with a porous Poly (L-lactic acid) (PLLA) body by freeze-extraction method. A distinct porosity difference was obtained between the inner and outer surfaces of the implant as characterized by image analysis and Mercury porosimetry (9.8±2.2 µm vs. 36.7±11.4 µm, p≤0.05). On top, a thin PLLA film was added to optimize the growth of epithelial cells, which was confirmed by using human respiratory epithelial cells. To check the control of fibroblast movement, PKH26 labeled fibroblasts were seeded onto Titanium and Titanium/PLLA implants. The cell movement was quantified by confocal microscopy: in one week cells moved deeper in Ti samples compared to Ti/PLLA. Conclusions In vitro experiments showed that this new implant is effective for guiding different kind of cells it will contact upon implantation. Overall, this system would enable spatial and temporal control over cell migration by a gradient ranging from macroporosity to nanoporosity within a tracheal implant. Moreover, mechanical properties will be dependent mainly on the titanium frame. This will make it possible to create a polymeric environment which is suitable for cells without the need to meet mechanical

  10. A Hybrid Constant and Oscillatory Field Ion Mobility Analyzer Using Structures for Lossless Ion Manipulations

    Science.gov (United States)

    Prabhakaran, Aneesh; Hamid, Ahmed M.; Garimella, Sandilya V. B.; Valenzuela, Blandina R.; Ewing, Robert G.; Ibrahim, Yehia M.; Smith, Richard D.

    2018-02-01

    Here we explore the combination of constant and oscillatory fields applied in a single device to affect the continuous separation and filtering of ions based on their mobilities. The device explored allows confining and manipulating ions utilizing a combination of radio frequency (rf), direct current (DC) fields, and traveling waves (TW) in a structures for lossless ion manipulations (SLIM) module. We have investigated theoretically and experimentally a concept for continuous filtering of ions based on their mobilities where ions are mobility separated and selected by passage through two regions, both of which incorporated combined TW and constant fields providing opposing forces on the ions. The SLIM module was composed of two surfaces with mirror-image arrays of electrodes and had two regions where the different TW and opposing DC fields could be applied. The filtering capabilities are determined by the applied DC gradient and the TW parameters, such as speed, amplitude, and the TW sequence (i.e., the duty cycle of the traveling wave). The effects of different parameters on the sensitivity and the ion mobility (IM) resolution of the device have been investigated. By appropriately choosing the DC gradient and TW parameters for the two sections, it is possible to transmit ions of a selected mobility while filtering out others of both higher and lower mobility. The novel device described here provides a basis for the targeted analysis of compounds based upon the continuous selection of ions according to their mobility and without the need for high electric fields or pulsed injection.

  11. Kinetic-Controlled Formation of Bimetallic Metal-Organic Framework Hybrid Structures.

    Science.gov (United States)

    Guo, Wenhan; Xia, Wei; Cai, Kunting; Wu, Yingxiao; Qiu, Bin; Liang, Zibin; Qu, Chong; Zou, Ruqiang

    2017-11-01

    Heterometallic metal-organic frameworks (MOFs) are constructed from two or more kinds of metal ions, while still remaining their original topologies. Due to distinct reaction kinetics during MOF formation, partial distribution of different metals within a single MOF crystal can lead to sophisticated heterogeneous nanostructures. Here, this study reports an investigation of reaction kinetics for different metal ions in a bimetallic MOF system, the ZIF-8/67 (M(2-mIM) 2 , M = Zn for ZIF-8, and Co for ZIF-67, 2-mIM = 2-methylimidazole), by in situ optical method. Distinct kinetics of the two metals forming single-component MOFs are revealed, and when both Co and Zn ions are present in the starting solution, homogeneous distributions of the two metals are only achieved at high Co/Zn ratio, while at low Co/Zn ratio concentration gradient from Co-rich cores to Zn-rich shells is observed. Further, by adding the two metals in sequence, more sophisticated structures are achieved. Specifically, when Co 2+ is added first, ZIF-67@ZIF-8/67 core-shell nanocrystals are achieved with tunable core/shell thickness ratio depending on the time intervals; while when Zn 2+ is added first, only agglomerates of irregular shape form due to the weak nucleation ability of Zn 2+ . © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Hybrid Carbon Fibers/Carbon Nanotubes Structures for Next Generation Polymeric Composites

    Directory of Open Access Journals (Sweden)

    M. Al-Haik

    2010-01-01

    Full Text Available Pitch-based carbon fibers are commonly used to produce polymeric carbon fiber structural composites. Several investigations have reported different methods for dispersing and subsequently aligning carbon nanotubes (CNTs as a filler to reinforce polymer matrix. The significant difficulty in dispersing CNTs suggested the controlled-growth of CNTs on surfaces where they are needed. Here we compare between two techniques for depositing the catalyst iron used toward growing CNTs on pitch-based carbon fiber surfaces. Electrochemical deposition of iron using pulse voltametry is compared to DC magnetron iron sputtering. Carbon nanostructures growth was performed using a thermal CVD system. Characterization for comparison between both techniques was compared via SEM, TEM, and Raman spectroscopy analysis. It is shown that while both techniques were successful to grow CNTs on the carbon fiber surfaces, iron sputtering technique was capable of producing more uniform distribution of iron catalyst and thus multiwall carbon nanotubes (MWCNTs compared to MWCNTs grown using the electrochemical deposition of iron.

  13. The synthesis of novel hybrid thiol-functionalized nano-structured SBA-15

    International Nuclear Information System (INIS)

    Hoang, Van Duc; Dang, Tuyet Phuong; Dinh, Quang Khieu; Vu, Anh Tuan; Nguyen, Huu Phu

    2010-01-01

    Mesoporous thiol-functionalized SBA-15 has been directly synthesized by co-condensation of tetraethyl orthosilicate (TEOS) and 3-mercaptopropyltrimethoxysilane (MPTMS) with triblock copolymer P123 as-structure-directing agent under hydrothermal conditions. Surfactant removal was performed by Soxhlet ethanol extraction. These materials have been characterized by powder x-ray diffraction (XRD), nitrogen adsorption/desorption (BET model), transmission electron microscopy (TEM), thermal analysis, infrared spectroscopy (IR) and energy-dispersive x-ray spectroscopy (EDX). The main parameters, such as the initial molar ratio of MPTMS to TEOS, the time of adding MPTMS to synthesized gel and the Soxhlet ethanol extraction on the thiol functionalized SBA-15 with high thiol content and highly ordered hexagonal mesostructure, were investigated and evaluated. The adsorption capacity of the thiol-functionalized and non-functionalized SBA-15 materials for Pb 2+ ion from aqueous solution was tested. It was found that the Pb 2+ adsorption capacity of the thiol functionalized SBA-15 is three times higher than that of non-functionalized SBA-15

  14. Perovskite-based solar cells with inorganic inverted hybrid planar heterojunction structure

    Directory of Open Access Journals (Sweden)

    Wei-Chih Lai

    2018-01-01

    Full Text Available We demonstrated the good performance of inorganic inverted CH3NH3PbI3 perovskite-based solar cells (SCs with glass/ITO/NiOx/CH3NH3PbI3 perovskite/C60/ room temperature (RT-sputtered ZnO/Al structure. We adopted spin coating and RT sputtering for the deposition of NiOx and ZnO, respectively. The inorganic hole and electron transport layer of NiOx and RT-sputtered ZnO, respectively, could improve the open-circuit voltage (VOC, short-circuit current density (JSC, and power conversion efficiency (η% of the SCs. We obtained inorganic inverted CH3NH3PbI3 perovskite-based SCs with a JSC of 21.96 A/cm2, a VOC of 1.02 V, a fill factor (FF% of 68.2%, and an η% of 15.3% despite the sputtering damage of the RT-sputtered ZnO deposition. Moreover, the RT-sputtered ZnO could function as a diffusion barrier for Al, moisture, and O2. The inorganic inverted CH3NH3PbI3 perovskite-based SCs demonstrated improved storage reliability.

  15. Perovskite-based solar cells with inorganic inverted hybrid planar heterojunction structure

    Science.gov (United States)

    Lai, Wei-Chih; Lin, Kun-Wei; Guo, Tzung-Fang; Chen, Peter; Liao, Yuan-Yu

    2018-01-01

    We demonstrated the good performance of inorganic inverted CH3NH3PbI3 perovskite-based solar cells (SCs) with glass/ITO/NiOx/CH3NH3PbI3 perovskite/C60/ room temperature (RT)-sputtered ZnO/Al structure. We adopted spin coating and RT sputtering for the deposition of NiOx and ZnO, respectively. The inorganic hole and electron transport layer of NiOx and RT-sputtered ZnO, respectively, could improve the open-circuit voltage (VOC), short-circuit current density (JSC), and power conversion efficiency (η%) of the SCs. We obtained inorganic inverted CH3NH3PbI3 perovskite-based SCs with a JSC of 21.96 A/cm2, a VOC of 1.02 V, a fill factor (FF%) of 68.2%, and an η% of 15.3% despite the sputtering damage of the RT-sputtered ZnO deposition. Moreover, the RT-sputtered ZnO could function as a diffusion barrier for Al, moisture, and O2. The inorganic inverted CH3NH3PbI3 perovskite-based SCs demonstrated improved storage reliability.

  16. Metal-organic hybrid materials built with tetrachlorophthalate acid and different N-donor coligands: Structure diversity and photoluminescence

    Science.gov (United States)

    Xiao, Zhenyu; Yang, Xiao; Zhao, Siwei; Wang, Debao; Yang, Yu; Wang, Lei

    2016-02-01

    Eight new metal-organic hybrid materials, namely {Cd(Tcph)(4,4‧-bipy)1/2} (1), {[Cd2(Tcph)2(1,4-bimb)1/2(H2O)4]·H2O} (2), {Cd2(Tcph)2(1,4-bmimb)1/2(H2O)4} (3), {Cd(Tcph)(1,2-bmimb)} (4), {Cu(Tcph)(1,4-bimb)(H2O)} (5), {[Co(Tcph)(1,4-bimb)1/2(H2O)3]·(H2O)} (6), {Zn(Tcph)(1,2-bimb)} (7), {Cu2(Tcph)2(1,2-bimb)(H2O)4} (8), where Tcph=tetrachlorophthalate acid, 4,4‧-bipy=4,4‧-bipyridine, 1,4-bimb=1,4-bis(imidazol-1-ylmethyl)benzene, 1,4-bmimb=1,4-bis(2-methylimidazol-1-ylmethyl)benzene, 1,2-bimb=1,2-bis(imidazol-1-ylmethyl)-benzene, 1,2-bmimb=1,2-bis(2-methylimidazol-1-ylmethyl)benzene, have been synthesized and characterized. Their structures are determined by single crystal X-ray diffraction and further characterized by infrared spectra (IR) and thermogravimetric (TG) analyses. Complex 1, 4 and 7 display 2D layer structures. 1 possesses two-dimensional sheet containing an unusual [Cd(Tcph)] chains linked by 4,4‧-bipy co-ligand, while 4 and 7 hold the similar 4-connected 44-sql nets. Complex 2 and 3 feature a similar three dimensional (3D) internal compensation structure with a topology of {42·63·8}2{63}. 5 is a novel 2-fold self-penetrating 3D network with 4-coordinated 65·8-CdSO4 subnets. The ladder-like chains of 6 are further connected through O-H···O interactions to yield a 3D supramolecular structure. 8 is a discrete tetranuclear complex. The thermal stabilities of 1-8 and the luminescent properties of 1-4 and 7 in the solid state are also discussed.

  17. Active structural acoustic control of helicopter interior multifrequency noise using input-output-based hybrid control

    Science.gov (United States)

    Ma, Xunjun; Lu, Yang; Wang, Fengjiao

    2017-09-01

    This paper presents the recent advances in reduction of multifrequency noise inside helicopter cabin using an active structural acoustic control system, which is based on active gearbox struts technical approach. To attenuate the multifrequency gearbox vibrations and resulting noise, a new scheme of discrete model predictive sliding mode control has been proposed based on controlled auto-regressive moving average model. Its implementation only needs input/output data, hence a broader frequency range of controlled system is modelled and the burden on the state observer design is released. Furthermore, a new iteration form of the algorithm is designed, improving the developing efficiency and run speed. To verify the algorithm's effectiveness and self-adaptability, experiments of real-time active control are performed on a newly developed helicopter model system. The helicopter model can generate gear meshing vibration/noise similar to a real helicopter with specially designed gearbox and active struts. The algorithm's control abilities are sufficiently checked by single-input single-output and multiple-input multiple-output experiments via different feedback strategies progressively: (1) control gear meshing noise through attenuating vibrations at the key points on the transmission path, (2) directly control the gear meshing noise in the cabin using the actuators. Results confirm that the active control system is practical for cancelling multifrequency helicopter interior noise, which also weakens the frequency-modulation of the tones. For many cases, the attenuations of the measured noise exceed the level of 15 dB, with maximum reduction reaching 31 dB. Also, the control process is demonstrated to be smoother and faster.

  18. Hierarchical structures of β-TCP/45S5 bioglass hybrid scaffolds prepared by gelcasting.

    Science.gov (United States)

    Lopes, João Henrique; Magalhães, Jéssica Aparecida; Gouveia, Rubia Figueredo; Bertran, Celso Aparecido; Motisuke, Mariana; Camargo, Samira E A; Trichês, Eliandra de Sousa

    2016-09-01

    This paper investigates the microstructure and the mechanical properties of β-tricalcium phosphate (β-TCP) three-dimensional (3D) porous materials reinforced with 45S5 bioactive glass (BG). β-TCP and β-TCP/x%-BG scaffolds with interconnected pores networks, suitable for bone regeneration, were fabricated by gel-casting method. Mechanical properties, porosity, and morphological characteristics were evaluated by compressive strength test, scanning electron microscopy (SEM) and X-ray microtomography analysis, whereas the structures were fully explored by XRD, and Raman spectroscopy. To the best of our knowledge, this is the first time where the mechanism for understanding the effect of bioglass on the mechanical properties and microstruture of β-TCP/45S5-BG scaffolds has been systematically studied. The findings showed that ionic product lixiviated from 45S5 bioactive glass, rich in silicon species and sodium ion, catalyzes a phase transition from β-TCP to Si-TCP by replacement of phosphorus for silicon and contributes to the improvement of scaffolds mechanical properties. The compressive strength of β-TCP/5%-BG and β-TCP/7.5%-BG was improved around 200% in comparison to pure β-TCP. Osteoblast-like cells (MG 63) were exposed to the materials for 24h through the use of medium conditioned by β-tricalcium phosphate/bioactive glass. Cell viability was measured by MTT assay in the cells and the data obtained were submitted to ANOVA, Tukey׳s multiple comparison (pTCP/7.5-BG promoted an increase of cell proliferation. The results suggest that compositions and processing method studied may provide appropriate materials for tissue engineering. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. [Ploidy and genetic structure of hybrid populations of water frogs Pelophylax esculentus (L., 1758) complex (Amphibia, Ranidae) of Ukraine].

    Science.gov (United States)

    Mezhzherin, S V; Morozov-Leonov, S Iu; Rostovskaia, O V; Shabanov, D A; Sobolenko, L Iu

    2010-01-01

    The present study of green frog hybrid populations of Ukraine, including analysis of allozyme variability and planimetric analysis oferythrocytes size has confirmed that the unique region in this area is the Severski Donets basin The allopolyploid individuals there are met very frequently (5.7% of all investigated frogs). In other areas of Ukraine only two polyploid hybrids have been recorded. Beside that, one frog was defined as triploid Rana ridibundus. According to our investigations, all triploid hybrids from the Severski Donets basin are identified as P. esculentu (=lessonae)--2 ridibundus males.

  20. Assessing the Structural, Driver and Economic Impacts of Traffic Pole Mounted Wind Power Generator and Solar Panel Hybrid System

    Science.gov (United States)

    2012-06-01

    This project evaluates the physical and economic feasibility of using existing traffic infrastructure to mount wind power : generators. Some possible places to mount a light weight wind generator and solar panel hybrid system are: i) Traffic : signal...

  1. Hybrid Warfare

    Science.gov (United States)

    2013-08-01

    Office, Title 10, U.S. Code ; Act of 5 May 1960. 3. 2010 Quadrennial Defense Review Report, February 2010, 8. 4. Hybrid Warfare, Global Accountability...Rise of Hybrid Wars.” Proceedings 132 (November 2005); William J. Nemeth , Future War and Chechnya: A Case for Hybrid War- fare (master’s thesis, U.S...William J. Nemeth which represents the earliest scholarly work on the subject, in which the emergence of devolved hybrid societies gives rise to hybrid

  2. Hybrid vertical cavity laser

    DEFF Research Database (Denmark)

    Chung, Il-Sug; Mørk, Jesper

    2010-01-01

    A new hybrid vertical cavity laser structure for silicon photonics is suggested and numerically investigated. It incorporates a silicon subwavelength grating as a mirror and a lateral output coupler to a silicon ridge waveguide.......A new hybrid vertical cavity laser structure for silicon photonics is suggested and numerically investigated. It incorporates a silicon subwavelength grating as a mirror and a lateral output coupler to a silicon ridge waveguide....

  3. Structural, optical, and improved photocatalytic properties of CdS/SnO{sub 2} hybrid photocatalyst nanostructure

    Energy Technology Data Exchange (ETDEWEB)

    Venkata Reddy, Ch., E-mail: cvrphy@gmail.com [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of); Ravikumar, R.V.S.S.N. [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar 522510 (India); Srinivas, Ganganagunta [Engineering Department, lbra College of Technology, lbra 400 (Oman); Shim, Jaesool, E-mail: jshim@ynu.ac.kr [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of); Cho, Migyung, E-mail: mgcho@tu.ac.kr [Department of Game Engineering, Tongmyong University, Busan 608-711 (Korea, Republic of)

    2017-07-15

    Highlights: • CdS, SnO{sub 2}, and a CdS/SnO{sub 2} hybrid photocatalyst were synthesized using a two-step technique. • The dislocation density, strain values are higher for CdS/SnO{sub 2} hybrid photocatalyst. • The CdS/SnO{sub 2} has a higher surface area and smaller crystallite size compared to pristine CdS. • The CdS/SnO{sub 2} catalyst greatly reduced recombination of electron and hole pairs. - Abstract: CdS, SnO{sub 2} and CdS/SnO{sub 2} hybrid photocatalyst nanostructure were synthesized using a two-step (co-precipitation/hydrothermal) method. The as-prepared materials were characterized by powder X-ray diffraction, transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), surface analysis (BET), photoluminescence spectra (PL), UV–Vis diffusion reflectance spectroscopy (DRS), fourier transform infrared spectroscopy (FT-IR), and photocatalytic activity. The band gap energies calculated from the DRS results are 3.30, 2.15, and 2.99 eV for pristine SnO{sub 2}, CdS, and the CdS/SnO{sub 2} hybrid photocatalyst, respectively. The CdS/SnO{sub 2} hybrid photocatalyst showed more efficient charge carrier separation and improved photocatalytic degradation of methyl orange (MO). The highest degradation rate constant was achieved for the CdS/SnO{sub 2} hybrid photocatalyst (0.02434 min{sup −1}) compared to CdS (0.01381 min{sup −1}) and SnO{sub 2} (0.00878 min{sup −1}). The present study provides insights for improving the photocatalytic activity and photo-stability of CdS/SnO{sub 2} hybrid photocatalyst.

  4. Syntheses and structure characterization of ten acid-base hybrid crystals based on imidazole derivatives and mineral acids

    Science.gov (United States)

    Hu, Kaikai; Deng, Bowen; Jin, Shouwen; Ding, Aihua; Jin, Shide; Zhu, Jin; Zhang, Huan; Wang, Daqi

    2018-04-01

    Cocrystallization of the imidazole derivatives with a series of mineral acids gave a total of ten hybrid salts with the compositions: [(H2bzm)(Cl)2·3H2O] (1), [(H2bzm)(ClO4)2] (2), [(H2bze)(Cl)2·2H2O] (3), [(H2bze)(Br)2·2H2O] (4), [(H2bzp)(Cl)2·4H2O] (5), [(H2bzp)(Br)2·4H2O] (6), (2-(imidazol-1-yl)-1-phenylethanone): (phosphoric acid) [(Himpeta)+(H2PO4)-] (7), [(H2impd)(Br)2] (8), [(H2impd)(ClO4)2] (9), and [(Hbzml)(Cl)] (10). The ten salts have been characterised by X-ray diffraction analysis, IR, and elemental analysis, and the melting points of all the salts were also reported. And their structural and supramolecular aspects are fully analyzed. The result reveals that among the ten investigated crystals the ring N atoms of the imidazole are protonated when the acids are deprotonated, and the crystal packing is interpreted in terms of the strong charge-assisted classical H-bonds between the NH+ and deprotonated acidic groups. Further analysis of the crystal packing of the salts indicated that a different set of additional CHsbnd O, CH2sbnd O, CHsbnd Cl, CH2sbnd Cl, CHsbnd N, CHsbnd Br, CH2sbnd Br, Osbnd O, O-π, Br-π, CH-π, and π-π associations contribute to the stabilization and expansion of the total high-dimensional frameworks. For the coexistence of the various weak nonbonding interactions these structures adopted homo or hetero supramolecular synthons or both. Some classical supramolecular synthons, such as R21(7), R22(7), R22(8), and R42(8), usually observed in the organic solids, were again shown to be involved in constructing some of these H-bonding networks.

  5. Shyntesis and cytotoxicity evaluation in vitro of new compounds with hybrid structures of 8-flavoneacetic acid and quinolones; Sintesis y evaluacion citotoxica in vitro de nuevos compuestos con estructuras hibridas del acido 8-flavonacetico quinolonas

    Energy Technology Data Exchange (ETDEWEB)

    Biaa, M.F.; Castellano, J.M.; Emling, F.; Schlick, E. [Knoll, S.a., Madrid (Spain)

    1994-12-31

    Using the structural similarity between 8-flavoneacetic acid the antitumor quinolones, we have prepared some hybrid compounds on both systems and studied their cytotoxicity. None of the sinthesized compounds have shown sufficient interest for further development. 33 refs.

  6. Modeling of engine hydrodynamics equations on hybrid unstructured meshes; Modelisation des equations de l`hydrodynamique moteur sur maillage non structure hybride

    Energy Technology Data Exchange (ETDEWEB)

    Durand, A.

    1996-10-10

    In this thesis, we are interested in the modeling of the compressible Navier-Stokes equations in 2-D moving domains with hybrid meshes. This work, far from being restricted to these equations, could be generalized to any other convection-diffusion system written in conservative vector form. After having described the mathematical equations and elaborated on finite volume (FV) methods, numerical schemes and various meshes, we have selected the Galerkin FV method. This method consists in locating the unknowns at the mesh nodes, then in solving the convective terms by means of VF method - quasi 1-D by edge approximation - and the diffusive terms by means of the finite element (FE) method - P{sub 1} for the triangular and Q{sub 1} for the quadrilateral. The equivalence between the Galerkin FV method and a mass-lumped FE method for temporal terms allows the construction of a new control volume constructed by means of medians. Then, show its interest in comparison to the classical control volume constructed by means of medians. Then first-order in comparison to the classical control volume constructed bu means of medians. Then, the first-order Roe scheme and its extension to second-order by the MUSCL method are detailed Emphasis is laid on two calculations oF the Gradient integral. Numerous numerical tests as well as the comparison with another code validate the approach. In particular, we show that triangular meshes lead to less precise results compared to quadrilateral meshes in certain cases. Afterward, we switch to the dimensionless Navier-Stokes equations and we describe a simplified (Bubnov)-Galerkin FE method in the case of the quadrilaterals. The newly deduced computer code is validated bu the means of a vortex convection-diffusion for different Reynolds numbers. This test shows that only highly viscous flows give rise to equivalent solutions for both meshes. (author)

  7. Strongly Nonlinear Dependence of Energy Transfer Rate on sp(2) Carbon Content in Reduced Graphene Oxide-Quantum Dot Hybrid Structures.

    Science.gov (United States)

    Dong, Yitong; Son, Dong Hee

    2015-01-02

    The dependence of the energy transfer rate on the content of sp(2)-hybridized carbon atoms in the hybrid structures of reduced graphene oxide (RGO) and Mn-doped quantum dot (QD(Mn)) was investigated. Taking advantage of the sensitivity of QD(Mn)'s dopant luminescence lifetime only to the energy transfer process without interference from the charge transfer process, the correlation between the sp(2) carbon content in RGO and the rate of energy transfer from QD(Mn) to RGO was obtained. The rate of energy transfer showed a strongly superlinear increase with increasing sp(2) carbon content in RGO, suggesting the possible cooperative behavior of sp(2) carbon domains in the energy transfer process as the sp(2) carbon content increases.

  8. Coupling physical chemical techniques with hydrotalcite-like compounds to exploit their structural features and new multifunctional hybrids with luminescent properties.

    Science.gov (United States)

    Costantino, Umberto; Costantino, Ferdinando; Elisei, Fausto; Latterini, Loredana; Nocchetti, Morena

    2013-08-28

    Hydrotalcite-like compounds (HTlc), belonging to the large class of Layered Double Hydroxides (LDH), have excited wide interest owing to the incredible number of their potential and achieved applications in physical, chemical and bio-chemical fields. This perspective review deals with recent advances in the application of physical-chemical techniques for the study of HTlc structure and for the design and synthesis, using intercalation chemistry routes, of new hybrid materials. Firstly, a rapid survey on the most common synthetic strategies for the attainment of HTlc with different crystallinity degree and crystal size and for their modification to obtain hybrids has been made, and the use of coupled techniques (XRPD, luminescence, Solid State MAS NMR and Molecular Dynamics) to gain structural information is reported. Then, the design, synthesis and photophysical characterization of azoic dyes-intercalated and co-intercalated HTlc hybrid materials are described. Hybrids constituted of ZnAl-HTlc, co-intercalated with stearate anions and methyl orange or methyl yellow dyes, have been used as nanofillers of hydrophobic polymers. The polymeric nano-composites obtained have been characterized by means of XRPD patterns, Thermo-Gravimetric Analysis and Confocal Fluorescence Microscopy. This latter technique has been found to be an excellent, complementary and non-invasive tool to probe the dispersion degree of the fluorescent fillers into the polymeric matrices and their stability in the compounding process. Finally, the synthesis and spectroscopic characterization of nanoparticle (NP) decorated HTlc for advanced antimicrobial and photo-catalytic applications are also reported. The review terminates with a concluding short note and future trends.

  9. Charge separation and transfer in hybrid type II tunneling structures of CdTe and CdSe nanocrystals

    International Nuclear Information System (INIS)

    Gross, Dieter Konrad Michael

    2013-01-01

    Closely packed nanocrystal systems have been investigated in this thesis with respect to charge separation by charge carrier tunneling. Clustered and layered samples have been analyzed using PL-measurements and SPV-methods. The most important findings are reviewed in the following. A short outlook is also provided for potential further aspects and application of the presented results. The main purpose of this thesis was to find and quantify electronic tunneling transfer in closely packed self-assembled nanocrystal structures presenting quantum mechanical barriers of about 1 nm width. We successfully used hybrid assemblies of CdTe and CdSe nanocrystals where the expected type II alignment between CdTe and CdSe typically leads to a concentration of electrons in CdSe and holes in CdTe nanocrystals. We were able to prove the charge selectivity of the CdTe-CdSe nanocrystal interface which induces charge separation. We mainly investigated the effects related to the electron transfer from CdTe to CdSe nanocrystals. Closely packing was achieved by two independent methods: the disordered colloidal clustering in solution and the layered assembly on dry glass substrates. Both methods lead to an inter-particle distance of about 1 nm of mainly organic material which acts as a tunneling barrier. PL-spectroscopy was applied. The PL-quenching of the CdTe nanocrystals in hybrid assemblies indicates charge separation by electron transfer from CdTe to CdSe nanocrystals. A maximum quenching rate of up to 1/100 ps was measured leading to a significant global PL-quenching of up to about 70 % for the CdTe nanocrystals. It was shown that charge separation dynamics compete with energy transfer dynamics and that charge separation typically dominates. The quantum confinement effect was used to tune the energetic offset between the CdTe and CdSe nanocrystals. We thus observe a correlation of PL-quenching and offset of the energy states for the electron transfer. The investigated PL

  10. Charge separation and transfer in hybrid type II tunneling structures of CdTe and CdSe nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Gross, Dieter Konrad Michael

    2013-11-08

    Closely packed nanocrystal systems have been investigated in this thesis with respect to charge separation by charge carrier tunneling. Clustered and layered samples have been analyzed using PL-measurements and SPV-methods. The most important findings are reviewed in the following. A short outlook is also provided for potential further aspects and application of the presented results. The main purpose of this thesis was to find and quantify electronic tunneling transfer in closely packed self-assembled nanocrystal structures presenting quantum mechanical barriers of about 1 nm width. We successfully used hybrid assemblies of CdTe and CdSe nanocrystals where the expected type II alignment between CdTe and CdSe typically leads to a concentration of electrons in CdSe and holes in CdTe nanocrystals. We were able to prove the charge selectivity of the CdTe-CdSe nanocrystal interface which induces charge separation. We mainly investigated the effects related to the electron transfer from CdTe to CdSe nanocrystals. Closely packing was achieved by two independent methods: the disordered colloidal clustering in solution and the layered assembly on dry glass substrates. Both methods lead to an inter-particle distance of about 1 nm of mainly organic material which acts as a tunneling barrier. PL-spectroscopy was applied. The PL-quenching of the CdTe nanocrystals in hybrid assemblies indicates charge separation by electron transfer from CdTe to CdSe nanocrystals. A maximum quenching rate of up to 1/100 ps was measured leading to a significant global PL-quenching of up to about 70 % for the CdTe nanocrystals. It was shown that charge separation dynamics compete with energy transfer dynamics and that charge separation typically dominates. The quantum confinement effect was used to tune the energetic offset between the CdTe and CdSe nanocrystals. We thus observe a correlation of PL-quenching and offset of the energy states for the electron transfer. The investigated PL

  11. Hybrid organic-inorganic crystal structure of 4-(di-methyl-amino)-pyridinium di-methyl-ammonium tetra-chlorido-lead(II).

    Science.gov (United States)

    Benson, Cassidy A; Bateman, Gage; Cox, Jordan M; Benedict, Jason B

    2017-11-01

    The title compound, (C 2 H 8 N)(C 7 H 11 N 2 )[PbCl 4 ], is a hybrid organic-inorganic material. It crystallizes in the space group C 2/ c and contains one half of a mol-ecule of lead chloride, 4-(di-methyl-amino)-pyridinium, and di-methyl-ammonium in the asymmetric unit. The crystal structure exhibits chains of lead chloride capped by 4-(di-methyl-amino)-pyridinium and di-methyl-ammoium by hydrogen bonding. This creates a one-dimensional zipper-like structure down the a axis. The crystal structure is examined and compared to a similar structure containing lead chloride and di-methyl-benzene-1,4-diaminium.

  12. GPCR-I-TASSER: A hybrid approach to G protein-coupled receptor structure modeling and the application to the human genome

    Science.gov (United States)

    Zhang, Jian; Yang, Jianyi; Jang, Richard; Zhang, Yang

    2015-01-01

    SUMMARY Experimental structure determination remains very difficult for G protein-coupled receptors (GPCRs). We propose a new hybrid protocol to construct GPCR structure models that integrates experimental mutagenesis data with ab initio transmembrane (TM) helix assembly simulations. The method was tested on 24 known GPCRs where the ab initio TM-helix assembly procedure constructed the correct fold for 20 cases. When combined with weak-homology and sparse mutagenesis restraints, the method generated correct folds for all the tested cases with an average C-alpha RMSD 2.4 Å in the TM-regions. The new hybrid protocol was applied to model all 1026 GPCRs in the human genome, where 923 have a high confidence score that are expected to have correct folds; these contain many pharmaceutically important families with no previously solved structures, including Trace amine, Prostanoids, Releasing hormones, Melanocortins, Vasopressin and Neuropeptide Y receptors. The results demonstrate new progress on genome-wide structure modeling of transmembrane proteins. PMID:26190572

  13. Bubble-Bed Structural Models for Hybrid Flow Simulation: An Outlook Based on a CFD-Generated Flow Image

    Czech Academy of Sciences Publication Activity Database

    Staykov, P.; Fialová, Marie; Vlaev, S. D.

    2009-01-01

    Roč. 87, č. 5 (2009), s. 669-676 ISSN 0263-8762 Institutional research plan: CEZ:AV0Z40720504 Keywords : bubble column * hybrid modeling * phenomenological mixing models Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.223, year: 2009

  14. Magnon, phonon, and electron temperature profiles and the spin Seebeck effect in magnetic insulator/normal metal hybrid structures

    NARCIS (Netherlands)

    Schreier, M.; Kamra, A.; Weiler, M.; Xiao, J.; Bauer, G.E.W.; Gross, R.; Goennenwein, S.T.B.

    2013-01-01

    We calculate the phonon, electron, and magnon temperature profiles in yttrium iron garnet/platinum bilayers by diffusive theory with appropriate boundary conditions, in particular taking into account interfacial thermal resistances. Our calculations show that in thin film hybrids, the interface

  15. Structure and magnetic properties of SiO{sub 2}/PCL novel sol–gel organic–inorganic hybrid materials

    Energy Technology Data Exchange (ETDEWEB)

    Catauro, Michelina, E-mail: michelina.catauro@unina2.it [Department of Industrial and Information Engineering, Second University of Naples, Via Roma 29, 81031 Aversa (Italy); Bollino, Flavia [Department of Industrial and Information Engineering, Second University of Naples, Via Roma 29, 81031 Aversa (Italy); Cristina Mozzati, Maria [Department of Physics, CNISM and INSTM, University of Pavia, Via Bassi 6, 27100 Pavia (Italy); Ferrara, Chiara; Mustarelli, Piercarlo [Department of Chemistry, Section of Physical Chemistry, University of Pavia and INSTM, Via Taramelli 16, 27100 Pavia (Italy)

    2013-07-15

    Organic–inorganic nanocomposite materials have been synthesized via sol–gel. They consist of an inorganic SiO{sub 2} matrix, in which different percentages of poly(ε-caprolactone) (PCL) have been incorporated. The formation of H-bonds among the carbonyl groups of the polymer chains and Si–OH group of the inorganic matrix has been proved by means of Fourier transform infrared spectroscopy (FT-IR) analysis and has been confirmed by solid-state nuclear magnetic resonance (NMR). X-Ray diffraction (XRD) analysis highlighted the amorphous nature of the synthesized materials. Scanning electron microscope (SEM) micrograph and atomic force microscope (AFM) topography showed their homogeneous morphology and nanostructure nature. Considering the opportunity to synthesize these hybrid materials under microgravity conditions by means of magnetic levitation, superconducting quantum interference device (SQUID) magnetometry has been used to quantify their magnetic susceptibility. This measure has shown that the SiO{sub 2}/PCL hybrid materials are diamagnetic and that their diamagnetic susceptibility is independent of temperature and increases with the PCL amount. - Graphical abstract: Characterization and magnetic properties of SiO{sub 2}/PCL organic–inorganic hybrid materials synthesized via sol–gel. FT-IR, Fourier transform infrared spectroscopy; solid-state NMR: solid-state nuclear magnetic resonance; SQUID: superconducting quantum interference device. - Highlights: • Sol–gel synthesis of SiO{sub 2}/PCL amorphous class I organic–inorganic hybrid materials. • FT-IR and NMR analyses show the hydrogen bonds formation between SiO{sub 2} and PCL. • AFM and SEM analyses confirm that the SiO{sub 2}/PCL are homogenous hybrid materials. • The SQUID measures show that the simples are diamagnetic. • Diamagnetic susceptibility of SiO{sub 2}/PCL materials increases with the PCL amount.

  16. Effect of p–d hybridization, structural distortion and cation electronegativity on electronic properties of ZnSnX2 (X=P, As, Sb) chalcopyrite semiconductors

    International Nuclear Information System (INIS)

    Mishra, S.; Ganguli, B.

    2013-01-01

    Significant effects of p–d hybridization, structural distortion and cation-electro-negativity are found on band gap in ZnSnX 2 (X=P, As, Sb). Our study suggests these compounds to be direct band gap semiconductors with band gaps of 1.23, 0.68 and 0.19 eV respectively. Lattice constants, tetragonal distortion (η), anion displacement, bond lengths and bulk moduli are calculated by Density Functional Theory based on Tight binding Linear Muffin-Tin orbital method. Our result of structural properties is in good agreement with the available experimental and other theoretical results. Calculated band gaps also agree well with the experimental works within LDA limitation. Unlike other semiconductors in the group II–IV–V 2 , there is a reduction in the band gap of 0.22, 0.20 and 0.24 eV respectively in ZnSnX 2 (X=P, As, Sb) due to p–d hybridization. Structural distortion decreases band gap by 0.20, 0.12 and 0.10 eV respectively. We find that cation electronegativity effect is responsible for increasing the band gap relative to their binary analogs GaInP 2 , InGaAs 2 and GaInSb 2 respectively and increment are 0.13, 0.04 and 0.13 eV respectively. - Graphical abstract: One unit cell of ZnSnX 2 (X=P, As, Sb) chalcopyrite semiconductor. Semiconductors ZnSnX 2 (X=P, As, Sb) are found to be direct band gap semiconductors with band gaps 1.23, 0.68 and 0.19 eV respectively. The quantitative estimate of effects of p–d hybridization, structural distortion and cation electronegativity shows band gaps change significantly due to these effects. Highlights: ► ZnSnX 2 (X=P, As, Sb) are direct band gap semiconductors. ► These have band gaps of 1.23 eV, 0.68 eV and 0.19 eV respectively. ► The band gap reduction due to p–d hybridization is 13.41%, 18.51% and 40% respectively. ► Band gap reduction due to structural distortion is 12.12%, 11.11% and 16.66% respectively. ► Band gap increases 8.38%, 3.70% and 21.31% respectively due to cation electronegativity

  17. A compound structure of ELM based on feature selection and parameter optimization using hybrid backtracking search algorithm for wind speed forecasting

    International Nuclear Information System (INIS)

    Zhang, Chu; Zhou, Jianzhong; Li, Chaoshun; Fu, Wenlong; Peng, Tian

    2017-01-01

    Highlights: • A novel hybrid approach is proposed for wind speed forecasting. • The variational mode decomposition (VMD) is optimized to decompose the original wind speed series. • The input matrix and parameters of ELM are optimized simultaneously by using a hybrid BSA. • Results show that OVMD-HBSA-ELM achieves better performance in terms of prediction accuracy. - Abstract: Reliable wind speed forecasting is essential for wind power integration in wind power generation system. The purpose of paper is to develop a novel hybrid model for short-term wind speed forecasting and demonstrates its efficiency. In the proposed model, a compound structure of extreme learning machine (ELM) based on feature selection and parameter optimization using hybrid backtracking search algorithm (HBSA) is employed as the predictor. The real-valued BSA (RBSA) is exploited to search for the optimal combination of weights and bias of ELM while the binary-valued BSA (BBSA) is exploited as a feature selection method applying on the candidate inputs predefined by partial autocorrelation function (PACF) values to reconstruct the input-matrix. Due to the volatility and randomness of wind speed signal, an optimized variational mode decomposition (OVMD) is employed to eliminate the redundant noises. The parameters of the proposed OVMD are determined according to the center frequencies of the decomposed modes and the residual evaluation index (REI). The wind speed signal is decomposed into a few modes via OVMD. The aggregation of the forecasting results of these modes constructs the final forecasting result of the proposed model. The proposed hybrid model has been applied on the mean half-hour wind speed observation data from two wind farms in Inner Mongolia, China and 10-min wind speed data from the Sotavento Galicia wind farm are studied as an additional case. Parallel experiments have been designed to compare with the proposed model. Results obtained from this study indicate that the

  18. Hybrid Bloch brane

    Energy Technology Data Exchange (ETDEWEB)

    Bazeia, D.; Lima, Elisama E.M.; Losano, L. [Universidade Federal da Paraiba, Departamento de Fisica, Joao Pessoa, PB (Brazil)

    2017-02-15

    This work reports on models described by two real scalar fields coupled with gravity in the five-dimensional spacetime, with a warped geometry involving one infinite extra dimension. Through a mechanism that smoothly changes a thick brane into a hybrid brane, one investigates the appearance of hybrid branes hosting internal structure, characterized by the splitting on the energy density and the volcano potential, induced by the parameter which controls interactions between the two scalar fields. In particular, we investigate distinct symmetric and asymmetric hybrid brane scenarios. (orig.)

  19. Morphology and Structural Properties of Novel Short Linear Glucan/Protein Hybrid Nanoparticles and Their Influence on the Rheological Properties of Starch Gel.

    Science.gov (United States)

    Li, Xiaojing; Ji, Na; Li, Man; Zhang, Shuangling; Xiong, Liu; Sun, Qingjie

    2017-09-13

    Starch nanoparticles were potential texture modifiers. However, they have strong tendency to aggregate and poor water dispersibility, which limited their application. The interaction between glucan (prepared from starch by enzymatic modification) and protein could significantly improve the dispersity of starch nanoparticles and, thus, enhance the rheological properties of food gels. In this work, glucan/protein hybrid nanoparticles were successfully developed for the first time using short linear glucan (SLG) and edible proteins [soy protein isolate (SPI), rice protein (RP), and whey protein isolate (WPI)]. The results showed that the SLG/SPI hybrid nanoparticles exhibited hollow structures, of which the smallest size was approximately 10-20 nm when the SLG/SPI ratio was 10:5. In contrast, SLG/RP nanoparticles displayed flower-like superstructures, and SLG/WPI nanoparticles presented stacked lamellar nanostructures with a width of 5-10 nm and a length of 50-70 nm. In comparison to bare SLG nanoparticles, SLG/SPI and SLG/WPI hybrid nanoparticles had higher melting temperatures. The addition of all nanoparticles greatly increased the storage modulus of corn starch gels and decreased loss tangent values. Importantly, the G' value of starch gels increased by 567% with the addition of flower-like SLG/RP superstructures.

  20. Graph Structure-Based Simultaneous Localization and Mapping Using a Hybrid Method of 2D Laser Scan and Monocular Camera Image in Environments with Laser Scan Ambiguity

    Directory of Open Access Journals (Sweden)

    Taekjun Oh

    2015-07-01

    Full Text Available Localization is an essential issue for robot navigation, allowing the robot to perform tasks autonomously. However, in environments with laser scan ambiguity, such as long corridors, the conventional SLAM (simultaneous localization and mapping algorithms exploiting a laser scanner may not estimate the robot pose robustly. To resolve this problem, we propose a novel localization approach based on a hybrid method incorporating a 2D laser scanner and a monocular camera in the framework of a graph structure-based SLAM. 3D coordinates of image feature points are acquired through the hybrid method, with the assumption that the wall is normal to the ground and vertically flat. However, this assumption can be relieved, because the subsequent feature matching process rejects the outliers on an inclined or non-flat wall. Through graph optimization with constraints generated by the hybrid method, the final robot pose is estimated. To verify the effectiveness of the proposed method, real experiments were conducted in an indoor environment with a long corridor. The experimental results were compared with those of the conventional GMappingapproach. The results demonstrate that it is possible to localize the robot in environments with laser scan ambiguity in real time, and the performance of the proposed method is superior to that of the conventional approach.

  1. Effect of crystallinity and morphology of TiO2 nano-structures on TiO2:P3HT hybrid photovoltaic solar cells

    International Nuclear Information System (INIS)

    Boroomandnia, A.; Kasaeian, A.B.; Nikfarjam, A. et al.

    2015-01-01

    A comparative study has been made of hybrid solar cells based on poly(3-hexyl thiophene) (P3HT) and different nano-structures of TiO 2 . Electrospinning, which is a low cost production method for large area nanofibrous films, was employed to fabricate TiO 2 nanofibers and spin coating method was employed to fabricate organic-inorganic hybrid solar cells based on P3HT and TiO 2 nanostructures. The performance of the hybrid solar cells was analyzed for four density levels of the TiO 2 nanostructure. It was found that higher densities of TiO 2 leads to more interface area and generates excitons, so that the power conversion efficiency increases to 0.13. TiO 2 nanoparticles with power conversion efficiency of 0.15 showed better performance than TiO 2 nanofibers because of greater interface area. Also the crystallinity effect of the TiO 2 nanostructure on solar cell performance was investigated. Moreover, an improved photovoltaic performance was achieved after the interface modification, and the highest conversion efficiency was obtained from the N719 modified device at 241 nm, short-circuit photocurrent (J sc ) of 3.88 mA cm -2 , open-circuit voltage (V oc ) of 0.09 V and fill factor of 0.16; so that an overall conversion efficiency (η) of 0.35% was obtained. (author)

  2. Multiple-geographic-scale genetic structure of two mangrove tree species: the roles of mating system, hybridization, limited dispersal and extrinsic factors.

    Directory of Open Access Journals (Sweden)

    Gustavo M Mori

    Full Text Available Mangrove plants comprise a unique group of organisms that grow within the intertidal zones of tropical and subtropical regions and whose distributions are influenced by both biotic and abiotic factors. To understand how these extrinsic and intrinsic processes influence a more fundamental level of the biological hierarchy of mangroves, we studied the genetic diversity of two Neotropical mangrove trees, Avicenniagerminans and A. schaueriana, using microsatellites markers. As reported for other sea-dispersed species, there was a strong differentiation between A. germinans and A. schaueriana populations sampled north and south of the northeastern extremity of South America, likely due to the influence of marine superficial currents. Moreover, we observed fine-scale genetic structures even when no obvious physical barriers were present, indicating pollen and propagule dispersal limitation, which could be explained by isolation-by-distance coupled with mating system differences. We report the first evidence of ongoing hybridization between Avicennia species and that these hybrids are fertile, although this interspecific crossing has not contributed to an increase in the genetic diversity the populations where A. germinans and A. schaueriana hybridize. These findings highlight the complex interplay between intrinsic and extrinsic factors that shape the distribution of the genetic diversity in these sea-dispersed colonizer species.

  3. Multiple-Geographic-Scale Genetic Structure of Two Mangrove Tree Species: The Roles of Mating System, Hybridization, Limited Dispersal and Extrinsic Factors

    Science.gov (United States)

    Mori, Gustavo M.; Zucchi, Maria I.; Souza, Anete P.

    2015-01-01

    Mangrove plants comprise a unique group of organisms that grow within the intertidal zones of tropical and subtropical regions and whose distributions are influenced by both biotic and abiotic factors. To understand how these extrinsic and intrinsic processes influence a more fundamental level of the biological hierarchy of mangroves, we studied the genetic diversity of two Neotropical mangrove trees, Avicenniagerminans and A. schaueriana, using microsatellites markers. As reported for other sea-dispersed species, there was a strong differentiation between A. germinans and A. schaueriana populations sampled north and south of the northeastern extremity of South America, likely due to the influence of marine superficial currents. Moreover, we observed fine-scale genetic structures even when no obvious physical barriers were present, indicating pollen and propagule dispersal limitation, which could be explained by isolation-by-distance coupled with mating system differences. We report the first evidence of ongoing hybridization between Avicennia species and that these hybrids are fertile, although this interspecific crossing has not contributed to an increase in the genetic diversity the populations where A. germinans and A. schaueriana hybridize. These findings highlight the complex interplay between intrinsic and extrinsic factors that shape the distribution of the genetic diversity in these sea-dispersed colonizer species. PMID:25723532

  4. Use of stem sliced from in vitro plants of papaya (hybrid IBP 42-99 by obtained callus with embryogenic structure

    Directory of Open Access Journals (Sweden)

    Jorge Gallardo Colina

    2004-10-01

    Full Text Available Inside in vitro propagation via, the somatic embriogenesis offers possibilities of obtaining top volumes of production in a minor period of time and a lower cost, which are a method potentially more efficient than the regeneration via organogenesis. In papaya the somatic embryogenesis could have developed from zigotic embryos and axis hipocotilos, nevertheless in case of the hybrids these methods cannot be used and it becomes necessary to develop it from a somatic fabric, without link with the sexual reproduction. This work chased as main objective Evaluated the use of in vitro plants stem sections of the Carica papaya IBP 42-99 hybrid for the formation of callus with embryogenic structures. As plant material were use in vitro plants of the papaya hybrid IBP 42-99. For it there took sections of different parts of the stem from the meristem up to the base of the in vitro plants, was use the culture medium Nitsh and Nitsh supplemented with 1.5 mg.l-1 of 6-BAP and 1.5 mg.l-1 of AIA. It was achieved to obtain callus from the stem sections with the culture medium used, nevertheless, in the treatments where used cylinders inside 1.0 cm from the apex down, the best results were achieved. The use of in vitro plants stem sections as explant for the formation of callus in this vegetable species it opens new possibilities for his in vitro propagation, specially in case of resultant hybrids of genetic improvement programs. Key words: apexes, Carica papaya, callogenesis, somatic embryogenesis

  5. Structural studies of polypeptides: Mechanism of immunoglobin catalysis and helix propagation in hybrid sequence, disulfide containing peptides

    Energy Technology Data Exchange (ETDEWEB)

    Storrs, R.W.

    1992-08-01

    Catalytic immunoglobin fragments were studied Nuclear Magnetic Resonance spectroscopy to identify amino acid residues responsible for the catalytic activity. Small, hybrid sequence peptides were analyzed for helix propagation following covalent initiation and for activity related to the protein from which the helical sequence was derived. Hydrolysis of p-nitrophenyl carbonates and esters by specific immunoglobins is thought to involve charge complementarity. The pK of the transition state analog P-nitrophenyl phosphate bound to the immunoglobin fragment was determined by [sup 31]P-NMR to verify the juxtaposition of a positively charged amino acid to the binding/catalytic site. Optical studies of immunoglobin mediated photoreversal of cis, syn cyclobutane thymine dimers implicated tryptophan as the photosensitizing chromophore. Research shows the chemical environment of a single tryptophan residue is altered upon binding of the thymine dimer. This tryptophan residue was localized to within 20 [Angstrom] of the binding site through the use of a nitroxide paramagnetic species covalently attached to the thymine dimer. A hybrid sequence peptide was synthesized based on the bee venom peptide apamin in which the helical residues of apamin were replaced with those from the recognition helix of the bacteriophage 434 repressor protein. Oxidation of the disufide bonds occured uniformly in the proper 1-11, 3-15 orientation, stabilizing the 434 sequence in an [alpha]-helix. The glycine residue stopped helix propagation. Helix propagation in 2,2,2-trifluoroethanol mixtures was investigated in a second hybrid sequence peptide using the apamin-derived disulfide scaffold and the S-peptide sequence. The helix-stop signal previously observed was not observed in the NMR NOESY spectrum. Helical connectivities were seen throughout the S-peptide sequence. The apamin/S-peptide hybrid binded to the S-protein (residues 21-166 of ribonuclease A) and reconstituted enzymatic activity.

  6. Structural studies of polypeptides: Mechanism of immunoglobin catalysis and helix propagation in hybrid sequence, disulfide containing peptides

    Energy Technology Data Exchange (ETDEWEB)

    Storrs, Richard Wood [Univ. of California, Berkeley, CA (United States)

    1992-08-01

    Catalytic immunoglobin fragments were studied Nuclear Magnetic Resonance spectroscopy to identify amino acid residues responsible for the catalytic activity. Small, hybrid sequence peptides were analyzed for helix propagation following covalent initiation and for activity related to the protein from which the helical sequence was derived. Hydrolysis of p-nitrophenyl carbonates and esters by specific immunoglobins is thought to involve charge complementarity. The pK of the transition state analog P-nitrophenyl phosphate bound to the immunoglobin fragment was determined by 31P-NMR to verify the juxtaposition of a positively charged amino acid to the binding/catalytic site. Optical studies of immunoglobin mediated photoreversal of cis, syn cyclobutane thymine dimers implicated tryptophan as the photosensitizing chromophore. Research shows the chemical environment of a single tryptophan residue is altered upon binding of the thymine dimer. This tryptophan residue was localized to within 20 Å of the binding site through the use of a nitroxide paramagnetic species covalently attached to the thymine dimer. A hybrid sequence peptide was synthesized based on the bee venom peptide apamin in which the helical residues of apamin were replaced with those from the recognition helix of the bacteriophage 434 repressor protein. Oxidation of the disufide bonds occured uniformly in the proper 1-11, 3-15 orientation, stabilizing the 434 sequence in an α-helix. The glycine residue stopped helix propagation. Helix propagation in 2,2,2-trifluoroethanol mixtures was investigated in a second hybrid sequence peptide using the apamin-derived disulfide scaffold and the S-peptide sequence. The helix-stop signal previously observed was not observed in the NMR NOESY spectrum. Helical connectivities were seen throughout the S-peptide sequence. The apamin/S-peptide hybrid binded to the S-protein (residues 21-166 of ribonuclease A) and reconstituted enzymatic activity.

  7. The governance of hybrid organisations

    DEFF Research Database (Denmark)

    Spear, Roger; Cornforth, Chris

    2010-01-01

    The focus of this chapter is on the governance of third sector organizations (TSOs) and the challenges that are raised by hybridity. In particular it will focus on the question how does hybridity affect governance structures and processes and the challenges that governing bodies face?......The focus of this chapter is on the governance of third sector organizations (TSOs) and the challenges that are raised by hybridity. In particular it will focus on the question how does hybridity affect governance structures and processes and the challenges that governing bodies face?...

  8. Epitaxial growth of hybrid nanostructures

    Science.gov (United States)

    Tan, Chaoliang; Chen, Junze; Wu, Xue-Jun; Zhang, Hua

    2018-02-01

    Hybrid nanostructures are a class of materials that are typically composed of two or more different components, in which each component has at least one dimension on the nanoscale. The rational design and controlled synthesis of hybrid nanostructures are of great importance in enabling the fine tuning of their properties and functions. Epitaxial growth is a promising approach to the controlled synthesis of hybrid nanostructures with desired structures, crystal phases, exposed facets and/or interfaces. This Review provides a critical summary of the state of the art in the field of epitaxial growth of hybrid nanostructures. We discuss the historical development, architectures and compositions, epitaxy methods, characterization techniques and advantages of epitaxial hybrid nanostructures. Finally, we provide insight into future research directions in this area, which include the epitaxial growth of hybrid nanostructures from a wider range of materials, the study of the underlying mechanism and determining the role of epitaxial growth in influencing the properties and application performance of hybrid nanostructures.

  9. Optimisation of the geometry of the drill bit and process parameters for cutting hybrid composite/metal structures in new aircrafts

    Science.gov (United States)

    Isbilir, Ozden

    Owing to their desirable strength-to-weight characteristics, carbon fibre reinforced polymer composites have been favourite materials for structural applications in different industries such as aerospace, transport, sports and energy. They provide a weight reduction in whole structure and consequently decrease fuel consumption. The use of lightweight materials such as titanium and its alloys in modern aircrafts has also increased significantly in the last couple of decades. Titanium and its alloys offer high strength/weight ratio, high compressive and tensile strength at high temperatures, low density, excellent corrosion resistance, exceptional erosion resistance, superior fatigue resistance and relatively low modulus of elasticity. Although composite/metal hybrid structures are increasingly used in airframes nowadays, number of studies regarding drilling of composite/metal stacks is very limited. During drilling of multilayer materials different problems may arise due to very different attributes of these materials. Machining conditions of drilling such structures play an important role on tool wear, quality of holes and cost of machining.. The research work in this thesis is aimed to investigate drilling of CFRP/Ti6Al4V hybrid structure and to optimize process parameters and drill geometry. The research work consist complete experimental study including drilling tests, in-situ and post measurements and related analysis; and finite element analysis including fully 3-D finite element models. The experimental investigations focused on drilling outputs such as thrust force, torque, delamination, burr formation, surface roughness and tool wear. An algorithm was developed to analyse drilling induced delamination quantitatively based on the images. In the numerical analysis, novel 3-D finite element models of drilling of CFRP, Ti6Al4V and CFRP/Ti6Al4V hybrid structure were developed with the use of 3-D complex drill geometries. A user defined subroutine was developed

  10. C9/12 Ribbon-Like Structures in Hybrid Peptides Alternating α- and Thiazole-Based γ-Amino Acids.

    Science.gov (United States)

    Bonnel, Clément; Legrand, Baptiste; Simon, Matthieu; Martinez, Jean; Bantignies, Jean-Louis; Kang, Young Kee; Wenger, Emmanuel; Hoh, Francois; Masurier, Nicolas; Maillard, Ludovic T

    2017-12-11

    According to their restricted conformational freedom, heterocyclic γ-amino acids are usually considered to be related to Z-vinylogous γ-amino acids. In this context, oligomers alternating α-amino acids and thiazole-based γ-amino acids (ATCs) were expected to fold into a canonical 12-helical shape as described for α/γ-hybrid peptides composed of cis-α/β-unsaturated γ-amino acids. However, through a combination of X-ray crystallography, NMR spectroscopy, FTIR experiments, and DFT calculations, it was determined that the folding behavior of ATC-containing hybrid peptides is much more complex. The homochiral α/(S)-ATC sequences were unable to adopt a stable conformation, whereas the heterochiral α/(R)-ATC peptides displayed novel ribbon structures stabilized by unusual C 9/12 -bifurcated hydrogen bonds. These ribbon structures could be considered as a succession of pre-organized γ/α dipeptides and may provide the basis for designing original α-helix mimics. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Molecular structure of hybrid imino-chalcone in the solid state: X-ray diffraction, spectroscopy study and third-order nonlinear optical properties

    Science.gov (United States)

    Custodio, J. M. F.; Santos, F. G.; Vaz, W. F.; Cunha, C. E. P.; Silveira, R. G.; Anjos, M. M.; Campos, C. E. M.; Oliveira, G. R.; Martins, F. T.; da Silva, C. C.; Valverde, C.; Baseia, B.; Napolitano, H. B.

    2018-04-01

    A comprehensive structural study of the compound (2E)-1-((E)-4-(4-methoxybenzylideneamino)phenyl)-3-(4-methoxyphenyl)prop-2-en-1-one was carried out in this work. Single crystal X-ray diffraction (SCXRD), X-ray powder diffraction (XRPD), NMR, Raman and Infrared spectroscopies, and DFT calculations were performed for characterization of this iminochalcone hybrid. Intermolecular interactions were described by Hirshfeld surface analysis derived from crystal structure. Reactivity and intramolecular charge transfer were investigated using the frontier molecular orbitals and molecular electrostatic potential. In addition, we have calculated the Nonlinear Optical Properties at the CAM-B3LYP/6-311+g(d) level of theory in the presence of different solvents (gas-phase, acetone, chloroform, dichloromethane, dimethyl sulfoxide, ethanol, methanol, and water), being found meaningful NLO parameters for our compound. At last, there is a good agreement between calculated and experimental IR spectrum, allowing the assignment of some of normal vibrational modes of the iminochalcone hybrid.

  12. Tuning the magnetic interactions in GaAs:Mn/MnAs hybrid structures by controlling shape and position of MnAs nanoclusters

    Energy Technology Data Exchange (ETDEWEB)

    Elm, Matthias Thomas

    2010-07-01

    In this work the magnetic properties of hexagonal MnAs nanoclusters and their influence on the transport properties of GaAs:Mn /MnAs hybrid structures were studied. Various arrangements of isolated nanoclusters and cluster chains were grown on (111)B-GaAs substrates by SA-MOVPE. The first part of this work deals with the manufacturing process of the different cluster arrangements investigated. By a suitable pre-structuring of the substrate it was possible to influence the cluster size, cluster shape and cluster position systematically. Preparing various arrangements it could be shown that the hexagonal nanoclusters prefer to grow along their a-axes. In the second part, the magnetic properties of the nanoclusters were studied. Ferromagnetic resonance (FMR) measurements show a hard magnetic axis perpendicular to the sample plane, i.e. parallel to the c-axis. By measurements, where the magnetic field was rotated in the sample plane, it could be demonstrated that the orientation of the magnetization can be forced into a certain direction by controlling the cluster shape. These results are confirmed by measurements using magnetic force microscopy. The third part deals with the influence of the nanoclusters and their arrangement on the transport properties of the GaAs:Mn matrix. For temperatures above 30 K the structures investigated show positive as well as negative magnetoresistance effects, which are typical for granular GaAs:Mn/MnAs hybrid structures. This behaviour can be explained in the context of transport in extended band states. The size of the magnetoresistance effects correlates strongly with the respective cluster arrangement of the sample. This behaviour has been predicted theoretically and could be confirmed experimentally in the context of this work. Below 30 K large positive magnetoresistance effects show up for the regular cluster arrangements, which cannot be observed for hybrid structures with random cluster distributions. These large positive

  13. Concept of hybrid embankment

    Directory of Open Access Journals (Sweden)

    Fukue Masaharu

    2015-06-01

    Full Text Available An innovative technique which is similar to a natural process, i.e., biogeochemical (carbonate diagenesis, is proposed to construct a hybrid embankment. In this study, the hybrid embankment is defined as a soil embankment which has a microbially induced framework structure of sand sheets and columns in the soft soil matrix. The sand materials are cemented with magnesium-calcite or dolomite, induced by ureolytic microbes. To design and construct hybrid embankments, fundamental problems, such as feasibility in terms of stability, geoenvironmental engineering practices, etc., are examined and discussed. It was shown that the hybrid embankment can be environmentally friendly and also can contribute solving technical and financial problems encountered in actual practice.

  14. Structural disorder and electronic hybridization in NicMg1-cO solid solutions probed by XANES at the oxygen K edge

    International Nuclear Information System (INIS)

    Chen Dongliang; Zhong Jun; Chu Wangsheng; Wu Ziyu; Kuzmin, Alexei; Mironova-Ulmane, Nina; Marcelli, Augusto

    2007-01-01

    A series of Ni c Mg 1-c O solid solutions has been studied for the first time looking at the structural disorder by means of x-ray absorption near-edge-structure (XANES) spectroscopy at the oxygen K edge. The experimental XANES signals were analysed within the full multiple scattering formalism and were interpreted taking into account clusters of up to 15 coordination shells around an absorbing oxygen atom. The substitution of nickel atoms by magnesium atoms results in a dramatic decrease of the empty density of states in the conduction band close to the Fermi level due to an exchange of the 3d(Ni)-2p(O) interaction with 3p(Mg)-2p(O). Besides, a simultaneous small decrease of the 3d(Ni)-2p(O) hybridization is also induced by the lattice expansion, determined by the difference in ionic radii between nickel and magnesium ions

  15. Structural disorder and electronic hybridization in Ni{sub c}Mg{sub 1-c}O solid solutions probed by XANES at the oxygen K edge

    Energy Technology Data Exchange (ETDEWEB)

    Chen Dongliang [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Zhong Jun [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Chu Wangsheng [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Wu Ziyu [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Kuzmin, Alexei [Institute of Solid State Physics, University of Latvia, Kengaraga 8, LV-1063 Riga (Latvia); Mironova-Ulmane, Nina [Institute of Solid State Physics, University of Latvia, Kengaraga 8, LV-1063 Riga (Latvia); Marcelli, Augusto [Laboratori Nazionali di Frascati, Istituto Nazionale di Fisica Nucleare, PO Box 13, 00044 Frascati (Italy)

    2007-09-05

    A series of Ni{sub c}Mg{sub 1-c}O solid solutions has been studied for the first time looking at the structural disorder by means of x-ray absorption near-edge-structure (XANES) spectroscopy at the oxygen K edge. The experimental XANES signals were analysed within the full multiple scattering formalism and were interpreted taking into account clusters of up to 15 coordination shells around an absorbing oxygen atom. The substitution of nickel atoms by magnesium atoms results in a dramatic decrease of the empty density of states in the conduction band close to the Fermi level due to an exchange of the 3d(Ni)-2p(O) interaction with 3p(Mg)-2p(O). Besides, a simultaneous small decrease of the 3d(Ni)-2p(O) hybridization is also induced by the lattice expansion, determined by the difference in ionic radii between nickel and magnesium ions.

  16. Synthesis and Electronic Structure of Boron-Graphdiyne with an sp-Hybridized Carbon Skeleton and Its Application in Sodium Storage.

    Science.gov (United States)

    Wang, Ning; Li, Xiaodong; Tu, Zeyi; Zhao, Fuhua; He, Jianjiang; Guan, Zhaoyong; Huang, Changshui; Yi, Yuanping; Li, Yuliang

    2018-04-03

    Boron-graphdiyne (BGDY), which has a unique π-conjugated structure comprising an sp-hybridized carbon skeleton and evenlydistributed boron heteroatoms in a well-organized 2D molecular plane, is prepared through a bottom-up synthetic strategy. Excellent conductivity, a relatively low band gap and a packing mode of the planar BGDY are observed. Notably, the unusual bonding environment of the all sp-carbon framework and the electron-deficient boron centers generates affinity to metal atoms, and thus provides extra binding sites. Furthermore, the expanded molecule pores of the BGDY molecular plane can also facilitate the transfer of metal ions in the perpendicular direction. The practical effect of the all sp-carbon structure and boron heteroatoms on the properties of BGDY are demonstrated in its performance as the anode in sodium-ion batteries. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. The porphyrin-iron hybrid hemoglobins. Absence of the Fe-His bonds in one type of subunits favors a deoxy-like structure with low oxygen affinity.

    Science.gov (United States)

    Fujii, M; Hori, H; Miyazaki, G; Morimoto, H; Yonetani, T

    1993-07-25

    Protoporphyrin-protoheme hybrid hemoglobins (Hb), in which the protohemes (Fe) in either the alpha- or beta-subunits were substituted with protoporphyrins IX (PP) alpha(PP)2 beta(Fe)2 and alpha(Fe)2 beta(PP)2 have been prepared. The structural and functional properties of these hybrid Hbs were investigated by measuring oxygen equilibrium curves and proton nuclear magnetic resonance spectra. The equilibrium constants of the first ligand, K1, observed for alpha(PP)2 beta(Fe)2 were much smaller than K1 values of HbA. The effects of pH and inositol hexaphosphate on K1 were substantially diminished. On the other hand, K1 values of alpha(Fe)2 beta(PP)2 were similar to those of HbA, including the pH and inositol hexaphosphate effects. The deoxy forms of alpha(PP)2 beta(Fe)2 and alpha(Fe)2 beta(PP)2 showed exchangeable proton resonances at 11 and 14 parts/million arising from the hydrogen bonds at the alpha 1 beta 2 contact in a deoxy-like structure. In the liganded form, these signals were dependent upon solution conditions. As K1 became larger, the reduction in the intensity of these signals was observed for both liganded forms. The resonance position of E11 Val originating from the beta subunits of alpha(PP)2 beta(Fe-CO)2 also varied in accordance with K1. We compare properties of PP-Fe hybrids with those of Co-Fe and Ni-Fe hybrids and conclude that the first oxygen binding to the beta heme may be linked to the metal-proximal His interaction in the alpha subunits. However, the first oxygen binding to the alpha heme is linked minimally to the metal-proximal His interaction in the beta subunits but may be correlated instead to the position of E11 Val relative to the porphyrin plane in the beta subunits.

  18. Ants exhibit asymmetric hybridization in a mosaic hybrid zone.

    Science.gov (United States)

    Purcell, Jessica; Zahnd, Sacha; Athanasiades, Anouk; Türler, Rebecca; Chapuisat, Michel; Brelsford, Alan

    2016-10-01

    Research on hybridization between species provides unparalleled insights into the pre- and postzygotic isolating mechanisms that drive speciation. In social organisms, colony-level incompatibilities may provide additional reproductive barriers not present in solitary species, and hybrid zones offer an opportunity to identify these barriers. Here, we use genotyping-by-sequencing to sequence hundreds of markers in a hybrid zone between two socially polymorphic ant species, Formica selysi and Formica cinerea. We characterize the zone, determine the frequency of hybrid workers, infer whether hybrid queens or males are produced and investigate whether hybridization is influenced by colony social organization. We also compare cuticular hydrocarbon profiles and aggression levels between the two species. The hybrid zone exhibits a mosaic structure. The asymmetric distribution of hybrids skewed towards F. cinerea suggests a pattern of unidirectional nuclear gene flow from F. selysi into F. cinerea. The occurrence of backcrossed individuals indicates that hybrid queens and/or males are fertile, and the presence of the F. cinerea mitochondrial haplotype in 97% of hybrids shows that successful F1 hybrids will generally have F. cinerea mothers and F. selysi fathers. We found no evidence that social organization contributes to speciation, because hybrids occur in both single-queen and multiple-queen colonies. Strongly differentiated cuticular hydrocarbon profiles and heightened interspecific aggression further reveal that species recognition cues are both present and perceived. The discovery of fertile hybrids and asymmetrical gene flow is unusual in ants, and this hybrid zone will therefore provide an ideal system with which to investigate speciation in social insects. © 2016 John Wiley & Sons Ltd.

  19. Effect of structure and viscosity of the components on some properties of starch-rich hybrid blends.

    Science.gov (United States)

    Ferreira, Willian H; Carmo, Marwin M I B; Silva, Ana Lúcia N; Andrade, Cristina T

    2015-03-06

    Glycerol-plasticized cornstarch and poly(lactic acid) (PLA) were melt-blended alone and at a constant 70:30 (m/m) composition, in the present of an organoclay. The effect of increasing contents of the organoclay on extruded and compression-molded samples was evaluated by X-ray diffraction (XRD), capillary rheometry, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and tensile tests. XRD and shear viscosity results obtained for the hybrid components (TPS/organoclay and PLA/organoclay) were correlated with the hybrid blends properties. XRD and TGA results suggested that the organoclay was similarly dispersed within both phases. SEM images revealed improved adhesion between the phases. Shear viscosities results indicated improved compatibilization as the organoclay content was increased. Some of the extruded materials were also submitted to injection molding, and characterized by SEM and by tensile tests. For the extruded and compression-molded samples, improved mechanical properties were obtained for the samples with higher contents of the organoclay. For the injection-molded samples, the mechanical properties seemed to be dependent on the organoclay dispersion. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Structural evolution of photocrosslinked silk fibroin and silk fibroin-based hybrid hydrogels: A small angle and ultra-small angle scattering investigation.

    Science.gov (United States)

    Whittaker, Jasmin L; Balu, Rajkamal; Knott, Robert; de Campo, Liliana; Mata, Jitendra P; Rehm, Christine; Hill, Anita J; Dutta, Naba K; Roy Choudhury, Namita

    2018-03-12

    Regenerated Bombyx mori silk fibroin (RSF) is a widely recognized protein for biomedical applications; however, its hierarchical gel structure is poorly understood. In this paper, the hierarchical structure of photocrosslinked RSF and RSF-based hybrid hydrogel systems: (i) RSF/Rec1-resilin and (ii) RSF/poly(N-vinylcaprolactam (PVCL) is reported for the first time using small-angle scattering (SAS) techniques. The structure of RSF in dilute to concentrated solution to fabricated hydrogels were characterized using small angle X-ray scattering (SAXS), small angle neutron scattering (SANS) and ultra-small angle neutron scattering (USANS) techniques. The RSF hydrogel exhibited three distinctive structural characteristics: (i) a Porod region in the length scale of 2 to 3nm due to hydrophobic domains (containing β-sheets) which exhibits sharp interfaces with the amorphous matrix of the hydrogel and the solvent, (ii) a Guinier region in the length scale of 4 to 20nm due to hydrophilic domains (containing turns and random coil), and (iii) a Porod-like region in the length scale of few micrometers due to water pores/channels exhibiting fractal-like characteristics. Addition of Rec1-resilin or PVCL to RSF and subsequent crosslinking systematically increased the nanoscale size of hydrophobic and hydrophilic domains, whereas decreased the homogeneity of pore size distribution in the microscale. The presented results have implications on the fundamental understanding of the structure-property relationship of RSF-based hydrogels. Copyright © 2018. Published by Elsevier B.V.