WorldWideScience

Sample records for metal refining

  1. Zone refining of plutonium metal

    International Nuclear Information System (INIS)

    Blau, M.S.

    1994-08-01

    The zone refining process was applied to Pu metal containing known amounts of impurities. Rod specimens of plutonium metal were melted into and contained in tantalum boats, each of which was passed horizontally through a three-turn, high-frequency coil in such a manner as to cause a narrow molten zone to pass through the Pu metal rod 10 times. The impurity elements Co, Cr, Fe, Ni, Np, U were found to move in the same direction as the molten zone as predicted by binary phase diagrams. The elements Al, Am, and Ga moved in the opposite direction of the molten zone as predicted by binary phase diagrams. As the impurity alloy was zone refined, δ-phase plutonium metal crystals were produced. The first few zone refining passes were more effective than each later pass because an oxide layer formed on the rod surface. There was no clear evidence of better impurity movement at the slower zone refining speed. Also, constant or variable coil power appeared to have no effect on impurity movement during a single run (10 passes). This experiment was the first step to developing a zone refining process for plutonium metal

  2. Structural refinement and coarsening in deformed metals

    DEFF Research Database (Denmark)

    Hansen, N.; Huang, X.; Xing, Q.

    2005-01-01

    The microstructural refinement by plastic deformation is analysed in terms of key parameters, the spacing between and the misorientation angle across the boundaries subdividing the structure. Coarsening of such structures by annealing is also characterised. For both deformed and annealed structures...

  3. Structural refinement and coarsening in deformed metals

    DEFF Research Database (Denmark)

    Hansen, N.; Huang, X.; Xing, Q.

    2005-01-01

    The microstructural refinement by plastic deformation is analysed in terms of key parameters, the spacing between and the misorientation angle across the boundaries subdividing the structure. Coarsening of such structures by annealing is also characterised. For both deformed and annealed structur......, good agreement has been found between experimental measurements of the flow stress and calculated values. Commercial purity aluminium is used as an example and deformed by cold rolling and by accumulative roll bonding....

  4. Progress in vacuum metal extraction, refining and consolidation

    International Nuclear Information System (INIS)

    Sundaram, C.V.; Mukherjee, T.K.; Sharma, B.P.

    1973-01-01

    The unique achievements in the process metallurgy of rare metals in the past quarter century should largely be attributed to advances in vacuum technology. New standards for high purity, increasing demand for pure metals and alloys for established applications, and steady improvement in sophistication and capacity of vacuum furnaces have provided the stimulus for developing and expanding vacuum metal extraction processes, and also exploring totally new processes. The paper discusses the thermochemistry of vacuum metallurgy, carbothermic and metallothermic reduction reactions, consolidation and refining by vacuum arc melting, electron beam melting and high temperature high vacuum sintering, and ultrapurification, with special reference to the reactive and refractory metals of Group IV to VI. (author)

  5. Optimization method for electron beam melting and refining of metals

    Science.gov (United States)

    Donchev, Veliko; Vutova, Katia

    2014-03-01

    Pure metals and special alloys obtained by electron beam melting and refining (EBMR) in vacuum, using electron beams as a heating source, have a lot of applications in nuclear and airspace industries, electronics, medicine, etc. An analytical optimization problem for the EBMR process based on mathematical heat model is proposed. The used criterion is integral functional minimization of a partial derivative of the temperature in the metal sample. The investigated technological parameters are the electron beam power, beam radius, the metal casting velocity, etc. The optimization problem is discretized using a non-stationary heat model and corresponding adapted Pismen-Rekford numerical scheme, developed by us and multidimensional trapezional rule. Thus a discrete optimization problem is built where the criterion is a function of technological process parameters. The discrete optimization problem is heuristically solved by cluster optimization method. Corresponding software for the optimization task is developed. The proposed optimization scheme can be applied for quality improvement of the pure metals (Ta, Ti, Cu, etc.) produced by the modern and ecological-friendly EBMR process.

  6. 19 CFR 19.22 - Withdrawal of metal refined in part from imported crude metal and in part from crude metal...

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Withdrawal of metal refined in part from imported crude metal and in part from crude metal produced from imported materials. 19.22 Section 19.22 Customs... § 19.22 Withdrawal of metal refined in part from imported crude metal and in part from crude metal...

  7. Review of Grain Refinement of Cast Metals Through Inoculation: Theories and Developments

    Science.gov (United States)

    Liu, Zhilin

    2017-10-01

    The inoculation method of grain refinement is widely used in research and industry. Because of its commercial and engineering importance, extensive research on the mechanisms/theories of grain refinement and development of effective grain refiners for diverse cast metals/alloys has been conducted. In 1999, Easton and St. John reviewed the mechanisms of grain refinement of cast Al alloys. Since then, grain refinement in alloys of Al, Mg, Fe, Ti, Cu, and Zn has evolved a lot. However, there is still no full consensus on the mechanisms/theories of grain refinement. Moreover, some new grain refiners developed based on the theories do not ensure efficient grain refinement. Thus, the factors that contribute to grain refinement are still not fully understood. Clarification of the prerequisite issues that occur in grain refinement is required using recent theories. This review covers multiple metals/alloys and developments in grain refinement from the last twenty years. The characteristics of effective grain refiners are considered from four perspectives: effective particle/matrix wetting configuration, sufficiently powerful segregating elements, preferential crystallographic matching, and geometrical features of effective nucleants. Then, recent mechanisms/theories on the grain refinement of cast metals/alloys are reviewed, including the peritectic-related, hypernucleation, inert nucleant, and constitutional supercooling-driven theories. Further, developments of deterministic and probabilistic modeling and nucleation crystallography in the grain refinement of cast metals are reviewed. Finally, the latest progress in the grain refinement of cast Zn and its alloys is described, and future work on grain refinement is summarized.

  8. Influence of Alloy and Solidification Parameters on Grain Refinement in Aluminum Weld Metal due to Inoculation

    Energy Technology Data Exchange (ETDEWEB)

    Schempp, Philipp [BAM, Germany; Tang, Z. [BIAS, Germany; Cross, Carl E. [Los Alamos National Laboratory; Seefeld, T. [BIAS, Germany; Pittner, A. [BAM, Germany; Rethmeier, M. [BAM, Germany

    2012-06-28

    The goals are: (1) Establish how much Ti/B grain refiner is need to completely refine aluminum weld metal for different alloys and different welding conditions; (2) Characterize how alloy composition and solidification parameters affect weld metal grain refinement; and (3) Apply relevant theory to understand observed behavior. Conclusions are: (1) additions of Ti/B grain refiner to weld metal in Alloys 1050, 5083, and 6082 resulted in significant grain refinement; (2) grain refinement was more effective in GTAW than LBW, resulting in finer grains at lower Ti content - reason is limited time available for equiaxed grain growth in LBW (inability to occlude columnar grain growth); (3) welding travel speed did not markedly affect grain size within GTAW and LBW clusters; and (4) application of Hunt CET analysis showed experimental G to be on the order of the critical G{sub CET}; G{sub CET} was consistently higher for GTAW than for LBW.

  9. Preparation and refining of rare earth metals by electrolytic routes

    International Nuclear Information System (INIS)

    Sahoo, D.K.

    2007-01-01

    Rare earth production has been gaining importance for the last 25 years for a variety of uses ranging from nuclear applications to hydrogen storage materials. Numerous techniques have been formulated to successfully extract pure metal from the ores and amongst them molten salt electrometallurgy looks promising. It being simple, environmental friendly makes the process technoeconomical for some rare earths. However serious issues like high temperature molten salt corrosion and suitability and selection of electrolytes needs to he considered to make the process an industrial one

  10. Refining of crude uranium by solvent extraction for production of nuclear pure uranium metal

    International Nuclear Information System (INIS)

    Gupta, S.K.; Manna, S.; Singha, M.; Hareendran, K.N.; Chowdhury, S.; Satpati, S.K.; Kumar, K.

    2007-01-01

    Uranium is the primary fuel material for any nuclear fission energy program. Natural uranium contains only 0.712% of 235 U as fissile constituent. This low concentration of fissile isotope in natural uranium calls for a very high level of purity, especially with respect to neutron poisons like B, Cd, Gd etc. before it can be used as nuclear fuel. Solvent extraction is a widely used technique by which crude uranium is purified for reactor use. Uranium metal plant (UMP), BARC, Trombay is engaged in refining of uranium concentrate for production of nuclear pure uranium metal for fabrication of fuel for research reactors. This paper reviews some of the fundamental aspects of this refining process with some special references to UMP, BARC. (author)

  11. Electrolytic systems and methods for making metal halides and refining metals

    Science.gov (United States)

    Holland, Justin M.; Cecala, David M.

    2015-05-26

    Disclosed are electrochemical cells and methods for producing a halide of a non-alkali metal and for electrorefining the halide. The systems typically involve an electrochemical cell having a cathode structure configured for dissolving a hydrogen halide that forms the halide into a molten salt of the halogen and an alkali metal. Typically a direct current voltage is applied across the cathode and an anode that is fabricated with the non-alkali metal such that the halide of the non-alkali metal is formed adjacent the anode. Electrorefining cells and methods involve applying a direct current voltage across the anode where the halide of the non-alkali metal is formed and the cathode where the non-alkali metal is electro-deposited. In a representative embodiment the halogen is chlorine, the alkali metal is lithium and the non-alkali metal is uranium.

  12. Disintegration and size reduction of slags and metals after melt refining of contaminated metallic wastes

    International Nuclear Information System (INIS)

    Heshmatpour, B.; Copeland, G.L.; Heestand, R.L.

    1981-04-01

    Melting under an oxidizing slag is an attractive method of decontaminating and reducing the volume of radioactively contaminated metal scrap. The contaminants are concentrated in a relatively small volume of slag, which leaves the metal essentially clean. A potential method of permanently disposing of the resulting slags (and metals if necessary) is emplacing them into deep shale by grout hydrofracture. Suspension in grout mixtures requires that the slag and metal be granular. The feasibility of size-reducing slags and disintegrating metals and subsequently incorporating both into grout mixtures was demonstrated. Various types of slags were crushed with a small jaw crusher into particles smaller than 3 mm. Several metals were also melted and water-blasted into coarse metal powder or shot ranging in size from 0.05 to 3 mm. A simple low-pressure water atomizer having a multiple nozzle with a converging-line jet stream was developed and used for this purpose. No significant slag dust and steam were generated during slag crushing and liquid-metal water-blasting tests, indicating that contamination can be well contained within the system. The crushed slags and the coarse metal powders were suspendable in group fluids, which indicates probable disposability by shale hydrofracture. The granulation of slags and metals facilitates their containment, transport, and storage

  13. A QM/MM refinement of an experimental DNA structure with metal-mediated base pairs.

    Science.gov (United States)

    Kumbhar, Sadhana; Johannsen, Silke; Sigel, Roland K O; Waller, Mark P; Müller, Jens

    2013-10-01

    A series of hybrid quantum mechanical/molecular mechanical (QM/MM) calculations was performed on models of a DNA duplex with artificial silver(I)-mediated imidazole base pairs. The optimized structures were compared to the original experimental NMR structure (Nat. Chem. 2 (2010) 229-234). The metal⋯metal distances are significantly shorter (~0.5Å) in the QM/MM model than in the original NMR structure. As a result, argentophilic interactions are feasible between the silver(I) ions of neighboring metal-mediated base pairs. Using the computationally determined metal⋯metal distances, a re-refined NMR solution structure of the DNA duplex was obtained. In this new NMR structure, all experimental constraints remain fulfilled. The new NMR structure shows less deviation from the regular B-type conformation than the original one. This investigation shows that the application of QM/MM models to generate additional constraints to be used during NMR structural refinements represents an elegant approach to obtaining high-resolution NMR structures. Copyright © 2013 Elsevier Inc. All rights reserved.

  14. Mesh refinement study and experimental validation for stretch bending of sheet metals

    Science.gov (United States)

    Raupach, M.; Kreissl, S.; Vuaille, L.; Möller, T.; Friebe, H.; Volk, W.

    2017-09-01

    For sheet metal parts with small radii and large bending angles, the sheet metal forming simulation reaches their application limits. Alternatives are complex shell formulations and volume elements. For volume elements, the necessary number of elements over the thickness is important. Valid values are not available depending on discrete radii. Therefore in this work, a convergence study is performed using the example of an angular stretch bend test with a radius to thickness ratio of 1. For various states of mesh refinement, simulations are performed, various results are presented, analysed and discussed with regard to convergence behaviour to the necessary number of elements in thickness direction. Recommendations for suitable validation variables are derived. Based on the refinement study, a simulation model for an experimental validation is developed. The experiments are carried out in a sheet metal forming machine. Experimental angular stretch bend test with a punch radius of 1 mm are performed until failure and the strain distribution on the top side of the sheet is measured. Finally, simulation and experiments are compared based on the surface strain.

  15. Direct Reduction of Waste through Refining of DOE Metal Assets - 13632

    International Nuclear Information System (INIS)

    Hargett, Michael C.; Terekhov, Dimitri; Khozan, Kamran M.

    2013-01-01

    CVMR R presents a technology for refining nickel from the enrichment barrier materials of the DOE that is proven through 100 years of use by the metals industry. CVMR R applies modern controls, instrumentation for process and monitoring of the system, and innovative production methods to produce a wide spectrum of products that generate new technology applications and improvements to our society and economy. CVMR R will receive barrier materials as a secure operation and size reduce the metal to a shred that is fed to a carbonylation reactor where nickel is reacted with carbon monoxide and generate nickel carbonyl. The carbonyl will be filtered and decomposed with heat to form a variety of products that include high value nano powders, coated substrates, net shapes and pure nickel. The residue from the reactor will retain radionuclides from enrichment activities. The carbon monoxide will only react and extract nickel under the operating conditions to leave volumetric contamination in the unreacted residue. A demonstration plant was designed and built by CVMR R and operated by BWXT, to demonstrate the systems capabilities to DOE in 2006. A pilot plant operation precedes the detailed design of the nickel refinery and provides essential data for design, safe work practices, waste characterizations and system kinetics and confirms the project feasibility. CVMR R produces nickel products that are cleaner than the nickel in U.S. commerce and used by industry today. The CVMR R process and systems for nickel refining is well suited for DOE materials and will provide value through environmental stewardship, recovery of high value assets, and support of the DOE environmental remediation programs as the refined nickel generates additional long term benefits to local communities. (authors)

  16. Direct Reduction of Waste through Refining of DOE Metal Assets - 13632

    Energy Technology Data Exchange (ETDEWEB)

    Hargett, Michael C.; Terekhov, Dimitri; Khozan, Kamran M. [Chemical Vapour Metal Refining - CVMR (United States)

    2013-07-01

    CVMR{sup R} presents a technology for refining nickel from the enrichment barrier materials of the DOE that is proven through 100 years of use by the metals industry. CVMR{sup R} applies modern controls, instrumentation for process and monitoring of the system, and innovative production methods to produce a wide spectrum of products that generate new technology applications and improvements to our society and economy. CVMR{sup R} will receive barrier materials as a secure operation and size reduce the metal to a shred that is fed to a carbonylation reactor where nickel is reacted with carbon monoxide and generate nickel carbonyl. The carbonyl will be filtered and decomposed with heat to form a variety of products that include high value nano powders, coated substrates, net shapes and pure nickel. The residue from the reactor will retain radionuclides from enrichment activities. The carbon monoxide will only react and extract nickel under the operating conditions to leave volumetric contamination in the unreacted residue. A demonstration plant was designed and built by CVMR{sup R} and operated by BWXT, to demonstrate the systems capabilities to DOE in 2006. A pilot plant operation precedes the detailed design of the nickel refinery and provides essential data for design, safe work practices, waste characterizations and system kinetics and confirms the project feasibility. CVMR{sup R} produces nickel products that are cleaner than the nickel in U.S. commerce and used by industry today. The CVMR{sup R} process and systems for nickel refining is well suited for DOE materials and will provide value through environmental stewardship, recovery of high value assets, and support of the DOE environmental remediation programs as the refined nickel generates additional long term benefits to local communities. (authors)

  17. Comparison of Some Rural Wastewater Refining Systems Considering Chemical Properties and Heavy Metals

    Directory of Open Access Journals (Sweden)

    Najme Yazdanpanah

    2016-02-01

    Full Text Available Introduction: Water scarcity is an important challenge worldwide, especially in arid and semi-arid regions. In these areas, the excessive exploitation of groundwater for irrigation, inefficient irrigation methods, irrigation with low-quality water and uncontrolled utilization of fertilizers in agricultural lands in addition to contamination of water resources by domestic and industrial wastewater in urban as well as rural regions, have led to water pollution problems. Furthermore, pollution and transportation of pollutants through wastewater have been considered as an environmental issue. Wastewater is a term that is used to describe waste materials that includes liquid waste and sewage waste. Wastewaters from single houses in the countryside that are not connected to sewers are generally treated on-site by septic tank systems or individual domestic wastewater treatment systems. Study on wastewater quality derived from refining systems in rural areas has been rarely taken into account. This study investigates the efficiency of some refining systems in the reduction of wastewater pollution indices and heavy metal concentrations. Materials and Methods: This study was done in four rural areas including Dehmilan, Hotkan, Sarbagh and Sekukan which are located around the city of Zarand in the Kerman province. Recently, some refining systems have been established in these areas in order to mitigate the environmental issues. An experiment was done to assess the efficiency of these refining systems and to determine the pollution indices for such small communities. Wastewater sampling was done in 10 replicates each at one week interval from four refineries. Different variables including BOD, COD, TOC, EC, TSS, TDS, DO, TKN, TP, pH, temperature, turbidity (Turb, alkanity (Alk and also the concentrations of Cd, Zn, Pb, Ni and Mo were measured using standard methods. To quantify the performance of each system, the amount of each variable at the outlet was

  18. Electron Beam Melting and Refining of Metals: Computational Modeling and Optimization

    Directory of Open Access Journals (Sweden)

    Veliko Donchev

    2013-10-01

    Full Text Available Computational modeling offers an opportunity for a better understanding and investigation of thermal transfer mechanisms. It can be used for the optimization of the electron beam melting process and for obtaining new materials with improved characteristics that have many applications in the power industry, medicine, instrument engineering, electronics, etc. A time-dependent 3D axis-symmetrical heat model for simulation of thermal transfer in metal ingots solidified in a water-cooled crucible at electron beam melting and refining (EBMR is developed. The model predicts the change in the temperature field in the casting ingot during the interaction of the beam with the material. A modified Pismen-Rekford numerical scheme to discretize the analytical model is developed. These equation systems, describing the thermal processes and main characteristics of the developed numerical method, are presented. In order to optimize the technological regimes, different criteria for better refinement and obtaining dendrite crystal structures are proposed. Analytical problems of mathematical optimization are formulated, discretized and heuristically solved by cluster methods. Using important for the practice simulation results, suggestions can be made for EBMR technology optimization. The proposed tool is important and useful for studying, control, optimization of EBMR process parameters and improving of the quality of the newly produced materials.

  19. Decontamination of metals by melt refinings/slagging: An annotated bibliography

    International Nuclear Information System (INIS)

    Mizia, R.E.; Worcester, S.A.; Twidwell, L.G.; Paolini, D.J.; Weldon, T.A.

    1993-07-01

    As the number of nuclear installations undergoing decontamination and decommissioning (D ampersand D) increases, current radioactive waste storage space is consumed and establishment of new waste storage areas becomes increasingly difficult, the problem of handling and storing radioactive scrap metal (RSM) gains increasing importance in the DOE Environmental Restoration and Waste Management Program. To alleviate present and future waste storage problems, Westinghouse Idaho Nuclear Company (WINCO) is managing a program for the recycling of RSM for beneficial use within the DOE complex. As part of that effort, Montana Tech has been awarded a contract to help optimize melting and refining technology for the recycling of stainless steel RSM. The scope of the Montana Tech program includes a literature survey, a decontaminating slag design study, small scale melting studies to determine optimum slag compositions for removal of radioactive contaminant surrogates, analysis of preferred melting techniques, and coordination of large scale melting demonstrations (100--500 lbs) to be conducted at selected facilities. The program will support recycling and decontaminating stainless steel RSM for use in waste canisters for Idaho Waste Immobilization Facility densified high level waste. This report is the result of the literature search conducted to establish a basis for experimental melt/slag program development

  20. Options report for the mining, non-ferrous metal smelting and refining industry

    International Nuclear Information System (INIS)

    1999-10-01

    This plant level analysis involved the study of three Canadian mines from ore extraction to refining. Energy consumption and GHG emissions from each facility were examined, along with projects to reduce these emissions. Results showed variation in emissions between firms by orders of magnitude, and while GHG reducing projects do exist, many are not implemented for economic and business reasons. Nevertheless, a modelling analysis of the mining industry as a whole showed that the industry should be able to reduce its GH emissions to within range of the Kyoto target. Enhanced voluntary initiatives, already supported by the industry, are seen as the most cost effective means of achieving these emission reductions. Industry experts suggest more effort to be expended on identifying GHG reducing technologies and competing projects with higher returns on investment. There is incontrovertible evidence that energy efficiency measures are often not implemented by the industry because their return on investment are not as attractive as those associated with process improvement projects. With appropriate assistance from government, such as funding for comprehensive energy audits similar to the plant level analysis done for this report, funding for carrying out the detailed economic evaluation of these projects, help with specialized human resources to participate in enhanced voluntary activities (such as the energy audits and life cycle cost/benefit analysis), and financial incentives to create more attractive returns on investment for energy efficiency/GHG emission reduction projects, the Canadian mining industry will be, and can be, part of the solution towards reducing GHG emissions. Other avenues that could be helpful in this effort include exporting Canadian mining technology to aid in reaching a global solution to a global problem, recognition for the Canadian mining industry for its northern operations, credit for Canada for embodied energy in exports, and recycling to

  1. Waste management of printed wiring boards: a life cycle assessment of the metals recycling chain from liberation through refining.

    Science.gov (United States)

    Xue, Mianqiang; Kendall, Alissa; Xu, Zhenming; Schoenung, Julie M

    2015-01-20

    Due to economic and societal reasons, informal activities including open burning, backyard recycling, and landfill are still the prevailing methods used for electronic waste treatment in developing countries. Great efforts have been made, especially in China, to promote formal approaches for electronic waste management by enacting laws, developing green recycling technologies, initiating pilot programs, etc. The formal recycling process can, however, engender environmental impact and resource consumption, although information on the environmental loads and resource consumption is currently limited. To quantitatively assess the environmental impact of the processes in a formal printed wiring board (PWB) recycling chain, life cycle assessment (LCA) was applied to a formal recycling chain that includes the steps from waste liberation through materials refining. The metal leaching in the refining stage was identified as a critical process, posing most of the environmental impact in the recycling chain. Global warming potential was the most significant environmental impact category after normalization and weighting, followed by fossil abiotic depletion potential, and marine aquatic eco-toxicity potential. Scenario modeling results showed that variations in the power source and chemical reagents consumption had the greatest influence on the environmental performance. The environmental impact from transportation used for PWB collection was also evaluated. The results were further compared to conventional primary metals production processes, highlighting the environmental benefit of metal recycling from waste PWBs. Optimizing the collection mode, increasing the precious metals recovery efficiency in the beneficiation stage and decreasing the chemical reagents consumption in the refining stage by effective materials liberation and separation are proposed as potential improvement strategies to make the recycling chain more environmentally friendly. The LCA results provide

  2. Synergistic Cytotoxic Stress and DNA Damage in Clover (Trifolium repens) Exposed to Heavy Metal Soil from Automobile Refining Shops in Kashmir-Himalaya

    OpenAIRE

    Mohsin Bhat, Towseef; Ansari, M. Y. K.; Choudhary, Sana; Aslam, Rumana; Alka

    2011-01-01

    Coexposure to heavy metals occurs in many occupational settings, such as automobile refining shops, pigment, and batteries production. Heavy metals around automobile refining shops were tested for their ability to induce synergistic cytogenetic effects in Trifolium repens L. by using the chromosomal aberrasions (CAs), micronucleus (MN) and comet assay. A significant increase in micronucleus (MN), chromosomal abrations (CAs), percentage of nuclei with comet tails (NCTs), the relative comet tai...

  3. Conditions for preparation of ultrapure beryllium by electrolytic refining in molten alkali-metal chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Wohlfarth, Hagen [Stuttgart Univ. (Germany)

    1982-02-01

    Electrolytic refining is regarded as the most suitable process for the production of beryllium with impurity contents below 1 at.-ppM. Several parameters are important for electrolytic refining of beryllium in a BeCl2-containing LiCl-KCl melt: current density, BeCl2 content, electrolyte temperature, composition of the unpurified beryllium and impurity-ion concentrations in the melt, as well as apparatus characteristics such as rotation speed of the cathode and condition of the crucible material. These factors were studied and optimized such that extensive removal of the maximum number of accompanying and alloying elements was achieved.

  4. Liquid Metal Embrittlement in Resistance Spot Welding and Hot Tensile Tests of Surface-refined TWIP Steels

    Science.gov (United States)

    Barthelmie, J.; Schram, A.; Wesling, V.

    2016-03-01

    Automotive industry strives to reduce vehicle weight and therefore fuel consumption and carbon dioxide emissions. Especially in the auto body, material light weight construction is practiced, but the occupant safety must be ensured. These requirements demand high-strength steels with good forming and crash characteristics. Such an approach is the use of high- manganese-content TWIP steels, which achieve strengths of around 1,000 MPa and fracture strains of more than 60%. Welding surface-refined TWIP steels reduces their elongation at break and produces cracks due to the contact with liquid metal and the subsequent liquid metal embrittlement (LME). The results of resistance spot welds of mixed joints of high-manganese- content steel in combination with micro-alloyed ferritic steel and hot tensile tests are presented. The influence of different welding parameters on the sensitivity to liquid metal embrittlement is investigated by means of spot welding. In a high temperature tensile testing machine, the influence of different parameters is determined regardless of the welding process. Defined strains just below or above the yield point, and at 25% of elongation at break, show the correlation between the applied strain and liquid metal crack initiation. Due to the possibility to carry out tensile tests on a wide range of temperatures, dependencies of different temperatures of the zinc coating to the steel can be identified. Furthermore, the attack time of the zinc on the base material is investigated by defined heating periods.

  5. Pareto-Lognormal Modeling of Known and Unknown Metal Resources. II. Method Refinement and Further Applications

    Energy Technology Data Exchange (ETDEWEB)

    Agterberg, Frits, E-mail: agterber@nrcan.gc.ca [Geological Survey of Canada (Canada)

    2017-07-01

    Pareto-lognormal modeling of worldwide metal deposit size–frequency distributions was proposed in an earlier paper (Agterberg in Nat Resour 26:3–20, 2017). In the current paper, the approach is applied to four metals (Cu, Zn, Au and Ag) and a number of model improvements are described and illustrated in detail for copper and gold. The new approach has become possible because of the very large inventory of worldwide metal deposit data recently published by Patiño Douce (Nat Resour 25:97–124, 2016c). Worldwide metal deposits for Cu, Zn and Ag follow basic lognormal size–frequency distributions that form straight lines on lognormal Q–Q plots. Au deposits show a departure from the straight-line model in the vicinity of their median size. Both largest and smallest deposits for the four metals taken as examples exhibit hyperbolic size–frequency relations and their Pareto coefficients are determined by fitting straight lines on log rank–log size plots. As originally pointed out by Patiño Douce (Nat Resour Res 25:365–387, 2016d), the upper Pareto tail cannot be distinguished clearly from the tail of what would be a secondary lognormal distribution. The method previously used in Agterberg (2017) for fitting the bridge function separating the largest deposit size–frequency Pareto tail from the basic lognormal is significantly improved in this paper. A new method is presented for estimating the approximate deposit size value at which the upper tail Pareto comes into effect. Although a theoretical explanation of the proposed Pareto-lognormal distribution model is not a required condition for its applicability, it is shown that existing double Pareto-lognormal models based on Brownian motion generalizations of the multiplicative central limit theorem are not applicable to worldwide metal deposits. Neither are various upper tail frequency amplification models in their present form. Although a physicochemical explanation remains possible, it is argued that

  6. Pareto-Lognormal Modeling of Known and Unknown Metal Resources. II. Method Refinement and Further Applications

    International Nuclear Information System (INIS)

    Agterberg, Frits

    2017-01-01

    Pareto-lognormal modeling of worldwide metal deposit size–frequency distributions was proposed in an earlier paper (Agterberg in Nat Resour 26:3–20, 2017). In the current paper, the approach is applied to four metals (Cu, Zn, Au and Ag) and a number of model improvements are described and illustrated in detail for copper and gold. The new approach has become possible because of the very large inventory of worldwide metal deposit data recently published by Patiño Douce (Nat Resour 25:97–124, 2016c). Worldwide metal deposits for Cu, Zn and Ag follow basic lognormal size–frequency distributions that form straight lines on lognormal Q–Q plots. Au deposits show a departure from the straight-line model in the vicinity of their median size. Both largest and smallest deposits for the four metals taken as examples exhibit hyperbolic size–frequency relations and their Pareto coefficients are determined by fitting straight lines on log rank–log size plots. As originally pointed out by Patiño Douce (Nat Resour Res 25:365–387, 2016d), the upper Pareto tail cannot be distinguished clearly from the tail of what would be a secondary lognormal distribution. The method previously used in Agterberg (2017) for fitting the bridge function separating the largest deposit size–frequency Pareto tail from the basic lognormal is significantly improved in this paper. A new method is presented for estimating the approximate deposit size value at which the upper tail Pareto comes into effect. Although a theoretical explanation of the proposed Pareto-lognormal distribution model is not a required condition for its applicability, it is shown that existing double Pareto-lognormal models based on Brownian motion generalizations of the multiplicative central limit theorem are not applicable to worldwide metal deposits. Neither are various upper tail frequency amplification models in their present form. Although a physicochemical explanation remains possible, it is argued that

  7. A review of recent advances on the effects of microstructural refinement and nano-catalytic additives on the hydrogen storage properties of metal and complex hydrides

    Energy Technology Data Exchange (ETDEWEB)

    Varin, R. A.; Zbroniec, L. [University of Waterloo, Department of Mechanical and Mechatronics Engineering, Waterloo, Ontario (Canada); Polanski, M.; Bystrzycki, J. [Faculty of Advanced Technology and Chemistry, Military University of Technology, Warsaw (Poland)

    2011-07-01

    The recent advances on the effects of microstructural refinement and various nano-catalytic additives on the hydrogen storage properties of metal and complex hydrides obtained in the last few years in the allied laboratories at the University of Waterloo (Canada) and Military University of Technology (Warsaw, Poland) are critically reviewed in this paper. The research results indicate that microstructural refinement (particle and grain size) induced by ball milling influences quite modestly the hydrogen storage properties of simple metal and complex metal hydrides. On the other hand, the addition of nanometric elemental metals acting as potent catalysts and/or metal halide catalytic precursors brings about profound improvements in the hydrogen absorption/desorption kinetics for simple metal and complex metal hydrides alike. In general, catalytic precursors react with the hydride matrix forming a metal salt and free nanometric or amorphous elemental metals/intermetallics which, in turn, act catalytically. However, these catalysts change only kinetic properties i.e. the hydrogen absorption/desorption rate but they do not change thermodynamics (e.g., enthalpy change of hydrogen sorption reactions). It is shown that a complex metal hydride, LiAlH{sub 4}, after high energy ball milling with a nanometric Ni metal catalyst and/or MnCl{sub 2} catalytic precursor, is able to desorb relatively large quantities of hydrogen at room temperature, 40 and 80 {sup o}C. This kind of behavior is very encouraging for the future development of solid state hydrogen systems. (authors)

  8. An Assessment Of Physicochemical Properties, Heavy Metal Enrichment And Fungal Characterization Of Refined Kerosene Impacted Soil In Anand, Gujarat, India

    Directory of Open Access Journals (Sweden)

    Shamiyan R Khan

    2013-12-01

    Full Text Available The present study was carried out to assess the physico-chemical properties, heavy metal enrichment and fungal isolation and characterization of the top soil samples collected in-situ from aged refined kerosene contaminated as well as uncontaminated garden soil sites in Anand, Gujarat, India. The total petroleum hydrocarbon (TPH concentrations were 17,510 mg/kg in kerosene contaminated soil against 142.65 mg/kg for uncontaminated soils. The contamination increased the soil organic carbon, nitrogen and clay to 2.95 %, 0.612 %, 36.22 % as compared to 1.5%, 0.153%, 32.4% respectively in the uncontaminated soil. Increased concentration of heavy metals like Cobalt, Copper, Iron, Zinc and Lead against the uncontaminated soil was encountered. Ten native fungal speciesbelonging to a total of five genera include Aspergillus (A. terreus, A. versicolor, A. niger; Fusarium oxysporum; Penicilliumjanthinellum from the uncontaminated garden soil, whereas the contaminated soil included Aspergillus (A. terreus, A. versicolor , A. niger Candida tropicalis,Cladosporiumbruhnei and Fusarium oxysporum, identified based on 18S rRNA and the nucleotide sequences were submitted to the NCBI, GenBank database. The changes created by kerosene contamination resulted in variation in individual concentrations of physicochemical properties, soil conductivity, pH and soil fertility indices probably dwindle the growth of fungal strains causing a reduction in the fungal population in the kerosene contaminated soil. International Journal of Environment, Volume-2, Issue-1, Sep-Nov 2013, Pages 164-174 DOI: http://dx.doi.org/10.3126/ije.v2i1.9219

  9. Assessment of levels and 'health-effects' of airborne particulate matter in mining, metal refining and metal working industries using nuclear and related analytical techniques

    International Nuclear Information System (INIS)

    2008-01-01

    The International Atomic Energy Agency (IAEA) has been supporting, over the years, several coordinated research programmes (CRPs) on various research topics related to environmental issues impacting human health. The primary aim of these CRPs has been to help enhance the research and development capabilities in the Member States, particularly among developing countries; to identify the sources of various environmental contaminants and evaluate their fate; and to provide for the basis of improved health among human populations by the use of nuclear and related analytical techniques. The CRP on Assessment of Levels and Health-Effects of Airborne Particulate Matter in Mining, Metal Refining and Metal Working Industries using nuclear and related analytical techniques focused on improving the competence for research on workplace monitoring in a variety of industrial environments. The personal monitoring of the APM (airborne particulate matter) of the exposed workforce was carried out for the first time by many participants. Nuclear and related analytical techniques, including the application of proton micro-beam, were used to generate the trace element concentration profiles in various biomarkers tissues of the exposed workers. The quality assurance/quality control (QA/QC) aspects related to the CRP were addressed through intercomparison analyses of APM on filter paper samples and freeze dried human urine samples to generate validated data. These data have helped to generate correlations between the occupational exposure measured and the magnitude of the biological response. Such new information is essential to evolve procedures to considerably reduce/eliminate the pollutants in the workplace environment and to make informed decisions on the evolution of standards in working environments aimed at preserving the health of workers. The purpose of this TECDOC is to provide an overview of the activities performed under the CRP by the participants. The overall achievements

  10. Impact of mining and refining on the distribution and accumulation of nickel and other heavy metals in sediments of subarctic Lake Kuetsjärvi, Murmansk Region, Russia.

    Science.gov (United States)

    Dauvalter, Vladimir

    2003-04-01

    Research on the influence of the activities of Pechenganickel Mining and Metallurgical Company on sediment heavy-metal geochemistry of the subarctic Lake Kuetsjärvi (north-western Russia) are described. It is estimated that during 60 years of mining/refining activity, 310 t of Ni, 120 t of Cu, 14 t of Co, 19 t of Zn, 0.087 t of Cd, 0.78 t of Pb and 0.053 t of Hg have accumulated in the lake sediments. The latter can be a source of secondary pollution and represent a danger for the lake ecosystem. The sedimentation rate in the lake is estimated to be within the range of 1.5-3 mm year(-1). The average concentrations of Ni, Cu, Hg and Co in superficial sediments have increased 25, 14, 11 and 5 times, respectively in the last century.

  11. Refining technology for the recycling of stainless steel radioactive scrap metals, FY 94 bi-annual report

    International Nuclear Information System (INIS)

    Mizia, R.E.; Atteridge, D.G.; Buckentin, J.; Carter, J.; Davis, H.L.; Devletian, J.H.; Scholl, M.R.; Turpin, R.B.; Webster, S.L.

    1994-08-01

    The research addressed under this project is the recycling of metallic nuclear-related by-product materials under the direction of Westinghouse Idaho Nuclear Company (WINCO). The program addresses the recycling of radioactive scrap metals (RSM) for beneficial re-use within the DOE complex; in particular, this program addresses the recycling of stainless steel RSM. It is anticipated that various stainless steel components under WINCO control at the Idaho Falls Engineering Laboratory (INEL), such as fuel pool criticality barriers and fuel storage racks will begin to be recycled in FY94-95. The end product of this recycling effort is expected to be waste and overpack canisters for densified high level waste for the Idaho Waste Immobilization Facility and/or the Universal Canister System for dry (interim) storage of spent fuel. The specific components of this problem area that are presently being, or have been, addressed by CAAMSEC are: (1) the melting/remelting of stainless steel RSM into billet form; (2) the melting/remelting initial research focus will be on the use of radioactive surrogates to study; (3) the cost effectiveness of RSM processing oriented towards privatization of RSM reuse and/or resale. Other components of this problem that may be addressed under program extension are: (4) the melting/remelting of carbon steel; (5) the processing of billet material into product form which shall meet all applicable ASTM requirements; and, (6) the fabrication of an actual prototypical product; the present concept of an end product is a low carbon Type 304/316 stainless steel cylindrical container for densified and/or vitrified high level radioactive waste and/or the Universal Canister System for dry (interim) storage of spent fuel. The specific work reported herein covers the melting/remelting of stainless steel open-quotes scrapclose quotes metal into billet form and the study of surrogate material removal effectiveness by various remelting techniques

  12. Spanish Refining

    International Nuclear Information System (INIS)

    Lores, F.R.

    2001-01-01

    An overview of petroleum refining in Spain is presented (by Repsol YPF) and some views on future trends are discussed. Spain depends heavily on imports. Sub-headings in the article cover: sources of crude imports, investments and logistics and marketing, -detailed data for each are shown diagrammatically. Tables show: (1) economic indicators (e.g. total GDP, vehicle numbers and inflation) for 1998-200; (2) crude oil imports for 1995-2000; (3) oil products balance for 1995-2000; (4) commodities demand, by product; (5) refining in Spain in terms of capacity per region; (6) outlets in Spain and other European countries in 2002 and (7) sales distribution channel by product

  13. Refined Hopf Link Revisited

    CERN Document Server

    Iqbal, Amer

    2012-01-01

    We establish a relation between the refined Hopf link invariant and the S-matrix of the refined Chern-Simons theory. We show that the refined open string partition function corresponding to the Hopf link, calculated using the refined topological vertex, when expressed in the basis of Macdonald polynomials gives the S-matrix of the refined Chern-Simons theory.

  14. Estimates of dietary exposure to bisphenol A (BPA) from light metal packaging using food consumption and packaging usage data: a refined deterministic approach and a fully probabilistic (FACET) approach.

    Science.gov (United States)

    Oldring, P K T; Castle, L; O'Mahony, C; Dixon, J

    2014-01-01

    The FACET tool is a probabilistic model to estimate exposure to chemicals in foodstuffs, originating from flavours, additives and food contact materials. This paper demonstrates the use of the FACET tool to estimate exposure to BPA (bisphenol A) from light metal packaging. For exposure to migrants from food packaging, FACET uses industry-supplied data on the occurrence of substances in the packaging, their concentrations and construction of the packaging, which were combined with data from a market research organisation and food consumption data supplied by national database managers. To illustrate the principles, UK packaging data were used together with consumption data from the UK National Diet and Nutrition Survey (NDNS) dietary survey for 19-64 year olds for a refined deterministic verification. The UK data were chosen mainly because the consumption surveys are detailed, data for UK packaging at a detailed level were available and, arguably, the UK population is composed of high consumers of packaged foodstuffs. Exposures were run for each food category that could give rise to BPA from light metal packaging. Consumer loyalty to a particular type of packaging, commonly referred to as packaging loyalty, was set. The BPA extraction levels used for the 15 types of coating chemistries that could release BPA were in the range of 0.00005-0.012 mg dm(-2). The estimates of exposure to BPA using FACET for the total diet were 0.0098 (mean) and 0.0466 (97.5th percentile) mg/person/day, corresponding to 0.00013 (mean) and 0.00059 (97.5th percentile) mg kg(-1) body weight day(-1) for consumers of foods packed in light metal packaging. This is well below the current EFSA (and other recognised bodies) TDI of 0.05 mg kg(-1) body weight day(-1). These probabilistic estimates were compared with estimates using a refined deterministic approach drawing on the same input data. The results from FACET for the mean, 95th and 97.5th percentile exposures to BPA lay between the

  15. The refined topological vertex

    International Nuclear Information System (INIS)

    Iqbal, Amer; Kozcaz, Can; Vafa, Cumrun

    2009-01-01

    We define a refined topological vertex which depends in addition on a parameter, which physically corresponds to extending the self-dual graviphoton field strength to a more general configuration. Using this refined topological vertex we compute, using geometric engineering, a two-parameter (equivariant) instanton expansion of gauge theories which reproduce the results of Nekrasov. The refined vertex is also expected to be related to Khovanov knot invariants.

  16. Creating value in refining

    International Nuclear Information System (INIS)

    Cobb, C.B.

    2001-01-01

    This article focuses on recent developments in the US refining industry and presents a model for improving the performance of refineries based on the analysis of the refining industry by Cap Gemini Ernst and Young. The identification of refineries in risk of failing, the construction of pipelines for refinery products from Gulf State refineries, mergers and acquisitions, and poor financial performance are discussed. Current challenges concerning the stagnant demand for refinery products, environmental regulations, and shareholder value are highlighted. The structure of the industry, the creation of value in refining, and the search for business models are examined. The top 25 US companies and US refining business groups are listed

  17. Relational Demonic Fuzzy Refinement

    Directory of Open Access Journals (Sweden)

    Fairouz Tchier

    2014-01-01

    Full Text Available We use relational algebra to define a refinement fuzzy order called demonic fuzzy refinement and also the associated fuzzy operators which are fuzzy demonic join (⊔fuz, fuzzy demonic meet (⊓fuz, and fuzzy demonic composition (□fuz. Our definitions and properties are illustrated by some examples using mathematica software (fuzzy logic.

  18. Melt refining of uranium contaminated copper, nickel, and mild steel

    International Nuclear Information System (INIS)

    Ren Xinwen; Liu Wencang; Zhang Yuan

    1993-01-01

    This paper presents the experiment results on melt refining of uranium contaminated metallic discards such as copper, nickel, and mild steel. Based on recommended processes, uranium contents in ingots shall decrease below 1 ppm; metal recovery is higher than 96%; and slag production is below 5% in weight of the metal to be refined. The uranium in the slag is homogeneously distributed. The slag seems to be hard ceramics, insoluble in water, and can be directly disposed of after proper packaging

  19. Replication, refinement & reachability

    DEFF Research Database (Denmark)

    Debois, Søren; Hildebrandt, Thomas T.; Slaats, Tijs

    2018-01-01

    We explore the complexity of reachability and run-time refinement under safety and liveness constraints in event-based process models. Our study is framed in the DCR? process language, which supports modular specification through a compositional operational semantics. DCR? encompasses the “Dynamic...... Condition Response (DCR) graphs” declarative process model for analysis, execution and safe run-time refinement of process-aware information systems; including replication of sub-processes. We prove that event-reachability and refinement are np-hard for DCR? processes without replication...

  20. Refining population health comparisons

    DEFF Research Database (Denmark)

    Hussain, M. Azhar; Jørgensen, Mette Møller; Østerdal, Lars Peter Raahave

    2016-01-01

    How to determine if a population group has better overall (multidimensional) health status than another is a central question in the health and social sciences. We apply a multidimensional first order dominance concept that does not rely on assumptions about the relative importance of each...... dimension. In particular, we show how one can explore the “depth” of dominance relations by gradually refining the health dimensions to see which dominance relations persist. We analyze a Danish health survey with many health indicators. These are initially collapsed into a single composite health dimension...... and then refined to four, seven, and ten health dimensions, each representing an (increasingly refined) area of health. Overall we find that younger age groups dominate older age groups in up to four dimensions, but no dominance relations are present with a more refined view of health. Comparing education groups...

  1. Relational Demonic Fuzzy Refinement

    OpenAIRE

    Tchier, Fairouz

    2014-01-01

    We use relational algebra to define a refinement fuzzy order called demonic fuzzy refinement and also the associated fuzzy operators which are fuzzy demonic join $({\\bigsqcup }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ , fuzzy demonic meet $({\\sqcap }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ , and fuzzy demonic composition $({\\square }_{\\mathrm{\\text{f}}\\mathrm{\\text{u}}\\mathrm{\\text{z}}})$ . Our definitions and properties are illustrated by some examples using ma...

  2. Some Properties of Refinement

    OpenAIRE

    Benjes, Friederike

    1996-01-01

    Two problems on action refinement are considered: First we treat the problem that there may exist configurations in the product ${\\cal E}_1~\\|_A~{\\cal E}_2$ of event structures that do not map to configurations of the individual event structures under projection. [Sch91] and [CZ89] showed that languages using only the operators $+, ;, ~\\|_A$ do not create event structures of that type. We show the same for languages extended with a refinement operator. In the second part the connection betwee...

  3. Refining and petrochemicals

    International Nuclear Information System (INIS)

    Constancio, Silva

    2006-01-01

    In 2004, refining margins showed a clear improvement that persisted throughout the first three quarters of 2005. This enabled oil companies to post significantly higher earnings for their refining activity in 2004 compared to 2003, with the results of the first half of 2005 confirming this trend. As for petrochemicals, despite a steady rise in the naphtha price, higher cash margins enabled a turnaround in 2004 as well as a clear improvement in oil company financial performance that should continue in 2005, judging by the net income figures reported for the first half-year. Despite this favorable business environment, capital expenditure in refining and petrochemicals remained at a low level, especially investment in new capacity, but a number of projects are being planned for the next five years. (author)

  4. Indian refining industry

    International Nuclear Information System (INIS)

    Singh, I.J.

    2002-01-01

    The author discusses the history of the Indian refining industry and ongoing developments under the headings: the present state; refinery configuration; Indian capabilities for refinery projects; and reforms in the refining industry. Tables lists India's petroleum refineries giving location and capacity; new refinery projects together with location and capacity; and expansion projects of Indian petroleum refineries. The Indian refinery industry has undergone substantial expansion as well as technological changes over the past years. There has been progressive technology upgrading, energy efficiency, better environmental control and improved capacity utilisation. Major reform processes have been set in motion by the government of India: converting the refining industry from a centrally controlled public sector dominated industry to a delicensed regime in a competitive market economy with the introduction of a liberal exploration policy; dismantling the administered price mechanism; and a 25 year hydrocarbon vision. (UK)

  5. Refining margins: recent trends

    International Nuclear Information System (INIS)

    Baudoin, C.; Favennec, J.P.

    1999-01-01

    Despite a business environment that was globally mediocre due primarily to the Asian crisis and to a mild winter in the northern hemisphere, the signs of improvement noted in the refining activity in 1996 were borne out in 1997. But the situation is not yet satisfactory in this sector: the low return on invested capital and the financing of environmental protection expenditure are giving cause for concern. In 1998, the drop in crude oil prices and the concomitant fall in petroleum product prices was ultimately rather favorable to margins. Two elements tended to put a damper on this relative optimism. First of all, margins continue to be extremely volatile and, secondly, the worsening of the economic and financial crisis observed during the summer made for a sharp decline in margins in all geographic regions, especially Asia. Since the beginning of 1999, refining margins are weak and utilization rates of refining capacities have decreased. (authors)

  6. Refining and petrochemicals

    Energy Technology Data Exchange (ETDEWEB)

    Constancio, Silva

    2006-07-01

    In 2004, refining margins showed a clear improvement that persisted throughout the first three quarters of 2005. This enabled oil companies to post significantly higher earnings for their refining activity in 2004 compared to 2003, with the results of the first half of 2005 confirming this trend. As for petrochemicals, despite a steady rise in the naphtha price, higher cash margins enabled a turnaround in 2004 as well as a clear improvement in oil company financial performance that should continue in 2005, judging by the net income figures reported for the first half-year. Despite this favorable business environment, capital expenditure in refining and petrochemicals remained at a low level, especially investment in new capacity, but a number of projects are being planned for the next five years. (author)

  7. Refining - Panorama 2008

    International Nuclear Information System (INIS)

    2008-01-01

    Investment rallied in 2007, and many distillation and conversion projects likely to reach the industrial stage were announced. With economic growth sustained in 2006 and still pronounced in 2007, oil demand remained strong - especially in emerging countries - and refining margins stayed high. Despite these favorable business conditions, tensions persisted in the refining sector, which has fallen far behind in terms of investing in refinery capacity. It will take renewed efforts over a long period to catch up. Looking at recent events that have affected the economy in many countries (e.g. the sub-prime crisis), prudence remains advisable

  8. Using OpenRefine

    CERN Document Server

    Verborgh, Ruben

    2013-01-01

    The book is styled on a Cookbook, containing recipes - combined with free datasets - which will turn readers into proficient OpenRefine users in the fastest possible way.This book is targeted at anyone who works on or handles a large amount of data. No prior knowledge of OpenRefine is required, as we start from the very beginning and gradually reveal more advanced features. You don't even need your own dataset, as we provide example data to try out the book's recipes.

  9. Panorama 2012 - Refining 2030

    International Nuclear Information System (INIS)

    Marion, Pierre; Saint-Antonin, Valerie

    2011-11-01

    The major uncertainty characterizing the global energy landscape impacts particularly on transport, which remains the virtually-exclusive bastion of the oil industry. The industry must therefore respond to increasing demand for mobility against a background marked by the emergence of alternatives to oil-based fuels and the need to reduce emissions of pollutants and greenhouse gases (GHG). It is in this context that the 'Refining 2030' study conducted by IFP Energies Nouvelles (IFPEN) forecasts what the global supply and demand balance for oil products could be, and highlights the type and geographical location of the refinery investment required. Our study shows that the bulk of the refining investment will be concentrated in the emerging countries (mainly those in Asia), whilst the areas historically strong in refining (Europe and North America) face reductions in capacity. In this context, the drastic reduction in the sulphur specification of bunker oil emerges as a structural issue for European refining, in the same way as increasingly restrictive regulation of refinery CO 2 emissions (quotas/taxation) and the persistent imbalance between gasoline and diesel fuels. (authors)

  10. Modified process for refining niobium by electron beam

    International Nuclear Information System (INIS)

    Pinatti, D.G.; Takano, C.

    1982-01-01

    The experimental results, thermodynamic equilibrium and kinetic theory of the metal/gas interaction in refractory metals are reviewed. The adsorption and desorption of nitrogen, hydrogen and CO are reversible, whereas those of oxygen are irreversible, with adsorption of an oxygen atom and volatilisation of the metal oxide. Based upon this fact, a new electron beam refining technology is proposed for niobium, consisting of four points: preparation of an electrode by aluminothermic reduction; zone refining in the first melt; kinetic refining in subsequent melts and compact design of the refining plant. Experimental results from a 300 kW pilot plant were in complete agreement with the technology proposed, giving 2.4 times the productivity predicted by the conventional technology. (Author) [pt

  11. Refinement by interface instantiation

    DEFF Research Database (Denmark)

    Hallerstede, Stefan; Hoang, Thai Son

    2012-01-01

    Decomposition is a technique to separate the design of a complex system into smaller sub-models, which improves scalability and team development. In the shared-variable decomposition approach for Event-B sub-models share external variables and communicate through external events which cannot...... be easily refined. Our first contribution hence is a proposal for a new construct called interface that encapsulates the external variables, along with a mechanism for interface instantiation. Using the new construct and mechanism, external variables can be refined consistently. Our second contribution...... is an approach for verifying the correctness of Event-B extensions using the supporting Rodin tool. We illustrate our approach by proving the correctness of interface instantiation....

  12. US refining reviewed

    International Nuclear Information System (INIS)

    Yamaguchi, N.D.

    1998-01-01

    The paper reviews the history, present position and future prospects of the petroleum industry in the USA. The main focus is on supply and demand, the high quality of the products, refinery capacity and product trade balances. Diagrams show historical trends in output, product demand, demand for transport fuels and oil, refinery capacity, refinery closures, and imports and exports. Some particularly salient points brought out were (i) production of US crude shows a marked downward trend but imports of crude will continue to increase, (ii) product demand will continue to grow even though the levels are already high, (iii) the demand is dominated by those products that typically yield the highest income for the refiner, (i.e. high quality transport fuels for environmental compliance), (iv) refinery capacity has decreased since 1980 and (v) refining will continue to have financial problems but will still be profitable. (UK)

  13. Issues in adaptive mesh refinement

    Energy Technology Data Exchange (ETDEWEB)

    Dai, William Wenlong [Los Alamos National Laboratory

    2009-01-01

    In this paper, we present an approach for a patch-based adaptive mesh refinement (AMR) for multi-physics simulations. The approach consists of clustering, symmetry preserving, mesh continuity, flux correction, communications, and management of patches. Among the special features of this patch-based AMR are symmetry preserving, efficiency of refinement, special implementation offlux correction, and patch management in parallel computing environments. Here, higher efficiency of refinement means less unnecessarily refined cells for a given set of cells to be refined. To demonstrate the capability of the AMR framework, hydrodynamics simulations with many levels of refinement are shown in both two- and three-dimensions.

  14. REFINING FLUORINATED COMPOUNDS

    Science.gov (United States)

    Linch, A.L.

    1963-01-01

    This invention relates to the method of refining a liquid perfluorinated hydrocarbon oil containing fluorocarbons from 12 to 28 carbon atoms per molecule by distilling between 150 deg C and 300 deg C at 10 mm Hg absolute pressure. The perfluorinated oil is washed with a chlorinated lower aliphatic hydrocarbon, which mairtains a separate liquid phase when mixed with the oil. Impurities detrimental to the stability of the oil are extracted by the chlorinated lower aliphatic hydrocarbon. (AEC)

  15. Future of French refining

    International Nuclear Information System (INIS)

    Calvet, B.

    1993-01-01

    Over recent years, the refining industry has had to grapple with a growing burden of environmental and safety regulations concerning not only its plants and other facilities, but also its end products. At the same time, it has had to bear the effects of the reduction of the special status that used to apply to petroleum, and the consequences of economic freedom, to which we should add, as specifically concerns the French market, the impact of energy policy and the pro-nuclear option. The result is a drop in heavy fuel oil from 36 million tonnes per year in 1973 to 6.3 million in 1992, and in home-heating fuel from 37 to 18 million per year. This fast-moving market is highly competitive. The French market in particular is wide open to imports, but the refining companies are still heavy exporters for those products with high added-value, like lubricants, jet fuel, and lead-free gasolines. The competition has led the refining companies to commit themselves to quality, and to publicize their efforts in this direction. This is why the long-term perspectives for petroleum fuels are still wide open. This is supported by the probable expectation that the goal of economic efficiency is likely to soften the effects of the energy policy, which penalizes petroleum products, in that they have now become competitive again. In the European context, with the challenge of environmental protection and the decline in heavy fuel outlets, French refining has to keep on improving the quality of its products and plants, which means major investments. The industry absolutely must return to a more normal level of profitability, in order to sustain this financial effort, and generate the prosperity of its high-performance plants and equipment. 1 fig., 5 tabs

  16. Panorama 2009 - refining

    International Nuclear Information System (INIS)

    2008-01-01

    For oil companies to invest in new refining and conversion capacity, favorable conditions over time are required. In other words, refining margins must remain high and demand sustained over a long period. That was the situation prevailing before the onset of the financial crisis in the second half of 2008. The economic conjuncture has taken a substantial turn for the worse since then and the forecasts for 2009 do not look bright. Oil demand is expected to decrease in the OECD countries and to grow much more slowly in the emerging countries. It is anticipated that refining margins will fall in 2009 - in 2008, they slipped significantly in the United States - as a result of increasingly sluggish demand, especially for light products. The next few months will probably be unfavorable to investment. In addition to a gloomy business outlook, there may also be a problem of access to sources of financing. As for investment projects, a mainstream trend has emerged in the last few years: a shift away from the regions that have historically been most active (the OECD countries) towards certain emerging countries, mostly in Asia or the Middle East. The new conjuncture will probably not change this trend

  17. Towards automated crystallographic structure refinement with phenix.refine

    Energy Technology Data Exchange (ETDEWEB)

    Afonine, Pavel V., E-mail: pafonine@lbl.gov; Grosse-Kunstleve, Ralf W.; Echols, Nathaniel; Headd, Jeffrey J.; Moriarty, Nigel W. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); Mustyakimov, Marat; Terwilliger, Thomas C. [Los Alamos National Laboratory, M888, Los Alamos, NM 87545 (United States); Urzhumtsev, Alexandre [CNRS–INSERM–UdS, 1 Rue Laurent Fries, BP 10142, 67404 Illkirch (France); Université Henri Poincaré, Nancy 1, BP 239, 54506 Vandoeuvre-lès-Nancy (France); Zwart, Peter H. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); Adams, Paul D. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); University of California Berkeley, Berkeley, CA 94720 (United States)

    2012-04-01

    phenix.refine is a program within the PHENIX package that supports crystallographic structure refinement against experimental data with a wide range of upper resolution limits using a large repertoire of model parameterizations. This paper presents an overview of the major phenix.refine features, with extensive literature references for readers interested in more detailed discussions of the methods. phenix.refine is a program within the PHENIX package that supports crystallographic structure refinement against experimental data with a wide range of upper resolution limits using a large repertoire of model parameterizations. It has several automation features and is also highly flexible. Several hundred parameters enable extensive customizations for complex use cases. Multiple user-defined refinement strategies can be applied to specific parts of the model in a single refinement run. An intuitive graphical user interface is available to guide novice users and to assist advanced users in managing refinement projects. X-ray or neutron diffraction data can be used separately or jointly in refinement. phenix.refine is tightly integrated into the PHENIX suite, where it serves as a critical component in automated model building, final structure refinement, structure validation and deposition to the wwPDB. This paper presents an overview of the major phenix.refine features, with extensive literature references for readers interested in more detailed discussions of the methods.

  18. Hirshfeld atom refinement.

    Science.gov (United States)

    Capelli, Silvia C; Bürgi, Hans-Beat; Dittrich, Birger; Grabowsky, Simon; Jayatilaka, Dylan

    2014-09-01

    Hirshfeld atom refinement (HAR) is a method which determines structural parameters from single-crystal X-ray diffraction data by using an aspherical atom partitioning of tailor-made ab initio quantum mechanical molecular electron densities without any further approximation. Here the original HAR method is extended by implementing an iterative procedure of successive cycles of electron density calculations, Hirshfeld atom scattering factor calculations and structural least-squares refinements, repeated until convergence. The importance of this iterative procedure is illustrated via the example of crystalline ammonia. The new HAR method is then applied to X-ray diffraction data of the dipeptide Gly-l-Ala measured at 12, 50, 100, 150, 220 and 295 K, using Hartree-Fock and BLYP density functional theory electron densities and three different basis sets. All positions and anisotropic displacement parameters (ADPs) are freely refined without constraints or restraints - even those for hydrogen atoms. The results are systematically compared with those from neutron diffraction experiments at the temperatures 12, 50, 150 and 295 K. Although non-hydrogen-atom ADPs differ by up to three combined standard uncertainties (csu's), all other structural parameters agree within less than 2 csu's. Using our best calculations (BLYP/cc-pVTZ, recommended for organic molecules), the accuracy of determining bond lengths involving hydrogen atoms from HAR is better than 0.009 Å for temperatures of 150 K or below; for hydrogen-atom ADPs it is better than 0.006 Å(2) as judged from the mean absolute X-ray minus neutron differences. These results are among the best ever obtained. Remarkably, the precision of determining bond lengths and ADPs for the hydrogen atoms from the HAR procedure is comparable with that from the neutron measurements - an outcome which is obtained with a routinely achievable resolution of the X-ray data of 0.65 Å.

  19. Refining and petrochemicals

    International Nuclear Information System (INIS)

    Benazzi, E.

    2003-01-01

    Down sharply in 2002, refining margins showed a clear improvement in the first half-year of 2003. As a result, the earnings reported by oil companies for financial year 2002 were significantly lower than in 2001, but the prospects are brighter for 2003. In the petrochemicals sector, slow demand and higher feedstock prices eroded margins in 2002, especially in Europe and the United States. The financial results for the first part of 2003 seem to indicate that sector profitability will not improve before 2004. (author)

  20. Refining and petrochemicals

    International Nuclear Information System (INIS)

    Benazzi, E.; Alario, F.

    2004-01-01

    In 2003, refining margins showed a clear improvement that continued throughout the first three quarters of 2004. Oil companies posted significantly higher earnings in 2003 compared to 2002, with the results of first quarter 2004 confirming this trend. Due to higher feedstock prices, the implementation of new capacity and more intense competition, the petrochemicals industry was not able to boost margins in 2003. In such difficult business conditions, aggravated by soaring crude prices, the petrochemicals industry is not likely to see any improvement in profitability before the second half of 2004. (author)

  1. Macromolecular crystallographic estructure refinement

    Directory of Open Access Journals (Sweden)

    Afonine, Pavel V.

    2015-04-01

    Full Text Available Model refinement is a key step in crystallographic structure determination that ensures final atomic structure of macromolecule represents measured diffraction data as good as possible. Several decades have been put into developing methods and computational tools to streamline this step. In this manuscript we provide a brief overview of major milestones of crystallographic computing and methods development pertinent to structure refinement.El refinamiento es un paso clave en el proceso de determinación de una estructura cristalográfica al garantizar que la estructura atómica de la macromolécula final represente de la mejor manera posible los datos de difracción. Han hecho falta varias décadas para poder desarrollar nuevos métodos y herramientas computacionales dirigidas a dinamizar esta etapa. En este artículo ofrecemos un breve resumen de los principales hitos en la computación cristalográfica y de los nuevos métodos relevantes para el refinamiento de estructuras.

  2. Petroleum refining industry in China

    International Nuclear Information System (INIS)

    Walls, W.D.

    2010-01-01

    The oil refining industry in China has faced rapid growth in oil imports of increasingly sour grades of crude with which to satisfy growing domestic demand for a slate of lighter and cleaner finished products sold at subsidized prices. At the same time, the world petroleum refining industry has been moving from one that serves primarily local and regional markets to one that serves global markets for finished products, as world refining capacity utilization has increased. Globally, refined product markets are likely to experience continued globalization until refining investments significantly expand capacity in key demand regions. We survey the oil refining industry in China in the context of the world market for heterogeneous crude oils and growing world trade in refined petroleum products.

  3. Refines Efficiency Improvement

    Energy Technology Data Exchange (ETDEWEB)

    WRI

    2002-05-15

    Refinery processes that convert heavy oils to lighter distillate fuels require heating for distillation, hydrogen addition or carbon rejection (coking). Efficiency is limited by the formation of insoluble carbon-rich coke deposits. Heat exchangers and other refinery units must be shut down for mechanical coke removal, resulting in a significant loss of output and revenue. When a residuum is heated above the temperature at which pyrolysis occurs (340 C, 650 F), there is typically an induction period before coke formation begins (Magaril and Aksenova 1968, Wiehe 1993). To avoid fouling, refiners often stop heating a residuum before coke formation begins, using arbitrary criteria. In many cases, this heating is stopped sooner than need be, resulting in less than maximum product yield. Western Research Institute (WRI) has developed innovative Coking Index concepts (patent pending) which can be used for process control by refiners to heat residua to the threshold, but not beyond the point at which coke formation begins when petroleum residua materials are heated at pyrolysis temperatures (Schabron et al. 2001). The development of this universal predictor solves a long standing problem in petroleum refining. These Coking Indexes have great potential value in improving the efficiency of distillation processes. The Coking Indexes were found to apply to residua in a universal manner, and the theoretical basis for the indexes has been established (Schabron et al. 2001a, 2001b, 2001c). For the first time, a few simple measurements indicates how close undesired coke formation is on the coke formation induction time line. The Coking Indexes can lead to new process controls that can improve refinery distillation efficiency by several percentage points. Petroleum residua consist of an ordered continuum of solvated polar materials usually referred to as asphaltenes dispersed in a lower polarity solvent phase held together by intermediate polarity materials usually referred to as

  4. Refining Radchem Detectors: Iridium

    Science.gov (United States)

    Arnold, C. W.; Bredeweg, T. A.; Vieira, D. J.; Bond, E. M.; Jandel, M.; Rusev, G.; Moody, W. A.; Ullmann, J. L.; Couture, A. J.; Mosby, S.; O'Donnell, J. M.; Haight, R. C.

    2013-10-01

    Accurate determination of neutron fluence is an important diagnostic of nuclear device performance, whether the device is a commercial reactor, a critical assembly or an explosive device. One important method for neutron fluence determination, generally referred to as dosimetry, is based on exploiting various threshold reactions of elements such as iridium. It is possible to infer details about the integrated neutron energy spectrum to which the dosimetry sample or ``radiochemical detector'' was exposed by measuring specific activation products post-irradiation. The ability of radchem detectors like iridium to give accurate neutron fluence measurements is limited by the precision of the cross-sections in the production/destruction network (189Ir-193Ir). The Detector for Advanced Neutron Capture Experiments (DANCE) located at LANSCE is ideal for refining neutron capture cross sections of iridium isotopes. Recent results from a measurement of neutron capture on 193-Ir are promising. Plans to measure other iridium isotopes are underway.

  5. Towards automated crystallographic structure refinement with phenix.refine

    Science.gov (United States)

    Afonine, Pavel V.; Grosse-Kunstleve, Ralf W.; Echols, Nathaniel; Headd, Jeffrey J.; Moriarty, Nigel W.; Mustyakimov, Marat; Terwilliger, Thomas C.; Urzhumtsev, Alexandre; Zwart, Peter H.; Adams, Paul D.

    2012-01-01

    phenix.refine is a program within the PHENIX package that supports crystallographic structure refinement against experimental data with a wide range of upper resolution limits using a large repertoire of model parameterizations. It has several automation features and is also highly flexible. Several hundred parameters enable extensive customizations for complex use cases. Multiple user-defined refinement strategies can be applied to specific parts of the model in a single refinement run. An intuitive graphical user interface is available to guide novice users and to assist advanced users in managing refinement projects. X-ray or neutron diffraction data can be used separately or jointly in refinement. phenix.refine is tightly integrated into the PHENIX suite, where it serves as a critical component in automated model building, final structure refinement, structure validation and deposition to the wwPDB. This paper presents an overview of the major phenix.refine features, with extensive literature references for readers interested in more detailed discussions of the methods. PMID:22505256

  6. Advances in uranium refining and conversion

    International Nuclear Information System (INIS)

    1987-05-01

    One of the most important steps in the nuclear fuel cycle is the uranium refining and conversion which goes from the yellow cake to three different products: uranium dioxide, natural metallic uranium and uranium hexafluoride. The total volume of this industry, at the present time, is nearly of 40,000 t U per year and at the end of the present century it would have reached the 60,000 t U per year. The refining and conversion of reprocessed uranium that can be extracted by treating irradiated fuel become equally important for recycling recovered fuel. In response to the growing interest in these topics, the IAEA convened a Technical Committee Meeting with the attendance of 37 experts from 21 countries. This technical document contains the 20 papers presented during the meeting. A separate abstract was prepared for each of these papers

  7. Comparing Refinements for Failure and Bisimulation Semantics

    NARCIS (Netherlands)

    Eshuis, H.; Fokkinga, M.M.

    2002-01-01

    Refinement in bisimulation semantics is defined differently from refinement in failure semantics: in bisimulation semantics refinement is based on simulations between labelled transition systems, whereas in failure semantics refinement is based on inclusions between failure systems. There exist

  8. Commercial refining in the Mediterranean

    International Nuclear Information System (INIS)

    Packer, P.

    1999-01-01

    About 9% of the world's oil refining capacity is on the Mediterranean: some of the world's biggest and most advanced refineries are on Sicily and Sardinia. The Mediterranean refineries are important suppliers to southern Europe and N. Africa. The article discusses commercial refining in the Mediterranean under the headings of (i) historic development, (ii) product demand, (iii) refinery configurations, (iv) refined product trade, (v) financial performance and (vi) future outlook. Although some difficulties are foreseen, refining in the Mediterranean is likely to continue to be important well into the 21st century. (UK)

  9. Co-ordinated research project on assessment of levels and health-effects of airborne particulate matter in mining, metal refining and metal working industries using nuclear and related analytical techniques. Report on the first research co-ordination meeting (RCM)

    International Nuclear Information System (INIS)

    1998-01-01

    The objectives of the CRP are to: (1) improve competence for research on workplace monitoring in terms of proper sampling and analytical procedures, (2) obtain relevant and reliable data on sources and levels of workplace pollution in various countries, (3) promote a better understanding of methods for the interpretation of such data including occupational heath studies, and (4) encourage closer collaboration between analytical scientists and researchers in the field of occupational health in the countries concerned. The CRP focuses on the use of nuclear and related analytical techniques for the following kinds of studies: (1) strategies and techniques for sampling of workplace airborne particulate matter and of human tissues and body fluids (hair, blood, etc.) sampling of exposed and non-exposed persons; (2) development of suitable analytical procedures for analysis of such types of samples; (3) workplace and personal monitoring of airborne particulate matter in the mining, refining and metal working industries, and the health effects of such exposure; and (4) tissue analysis of the workers exposed for biological monitoring and the health effects studies. This report includes the core and supplementary programme of the CRP; technical aspects of sampling, analysis, data processing, and quality assurance; and organizational aspects. The report includes also 10 papers contributed by the participants. Each individual contribution was indexed and provided with an abstract

  10. Physical refining of sunflower oil

    Directory of Open Access Journals (Sweden)

    Kovari Katalin

    2000-07-01

    Full Text Available Physical refining has several advantages compared to the classical chemical one. This process is more economical (improved yield, lower investment cost, less chemicals used environmental friendly process (no soapstock to be treated, splitted but more sensitive to the crude oil quality. Physical refining of sunflower oil is discussed in details. Recent developments in the field of processes, equipment and control have made it possible to refine by physical way the high phosphatide containing seed oils as well. Special degumming processes, improved performance of bleaching materials, better design of deodorizers are applied in new installations; huge capacity one-line physical refineries are successfully operated in different countries.

  11. Technology of niobium and molybdenum refining by electron beam

    International Nuclear Information System (INIS)

    Conti, R.A.; Pinatti, D.G.; Sandim, H.R.Z.

    1988-01-01

    The uses of metals and alloys in superconductors (Nb46%Ti), aerospatial industry (Ti6Al4V), electroeletronic industry (Nb, Mo, W) and in surgical implants (Ti, Nb) are increasing nowadays. A refining process of niobium and molybdenum by electron beam technique, since the oxides reduction till the obtention of a high purity ingot is presented. (C.G.C.) [pt

  12. Investigation of the influence of Ceratophyllum demersum to refine ...

    African Journals Online (AJOL)

    Water pollution has always been a major problem in the environment. Polluted water is harming for human health and need to clean water from pollution factors. One of the economic and rapid methods for elements removal is displacement metals by biosorption. The purpose of this study was refining diluted compost latex ...

  13. Preparation of high purity tellurium by zone refining

    Indian Academy of Sciences (India)

    This paper describes purification process of tellurium metal using zone refining technique under high purity hydrogen gas ambient in normal room environment. Process automation by newly designed stepper motor drive and allied process control instruments circumvent the complexity of electrical motors. It is observed that ...

  14. Steel refining possibilities in LF

    Science.gov (United States)

    Dumitru, M. G.; Ioana, A.; Constantin, N.; Ciobanu, F.; Pollifroni, M.

    2018-01-01

    This article presents the main possibilities for steel refining in Ladle Furnace (LF). These, are presented: steelmaking stages, steel refining through argon bottom stirring, online control of the bottom stirring, bottom stirring diagram during LF treatment of a heat, porous plug influence over the argon stirring, bottom stirring porous plug, analysis of porous plugs disposal on ladle bottom surface, bottom stirring simulation with ANSYS, bottom stirring simulation with Autodesk CFD.

  15. Adaptive Mesh Refinement in CTH

    International Nuclear Information System (INIS)

    Crawford, David

    1999-01-01

    This paper reports progress on implementing a new capability of adaptive mesh refinement into the Eulerian multimaterial shock- physics code CTH. The adaptivity is block-based with refinement and unrefinement occurring in an isotropic 2:1 manner. The code is designed to run on serial, multiprocessor and massive parallel platforms. An approximate factor of three in memory and performance improvements over comparable resolution non-adaptive calculations has-been demonstrated for a number of problems

  16. South Korea - oil refining overview

    International Nuclear Information System (INIS)

    Hayes, D.

    1999-01-01

    Following the economic problems of the 1990s, the petroleum refining industry of South Korea underwent much involuntary restructuring in 1999 with respect to takeovers and mergers and these are discussed. The demand for petroleum has now pretty well recovered. The reasons for fluctuating prices in the 1990s, how the new structure should be cushioned against changes in the future, and the potential for South Korea to export refined petroleum, are all discussed

  17. Limit of grain refinement during ECAP process. Temperature influence

    International Nuclear Information System (INIS)

    Chuvil'deev, V.N.; Kopylov, V.I.; Nokhrin, A.V.; Makarov, I.M.; Lopatin, Yu.G.

    2004-01-01

    Experimental and theoretical study results are reported for the process of deformation grain refinement under severe plastic deformation. A generalization is made for experimental study results on deformation dispersing of unalloyed metals and aluminium and magnesium base alloys. The model is built that allows calculating the value of minimum grain size attained by the method of equal-channel angular pressing. The expressions are derived which describe the dependence of grain refinement limit on the nature of material and the temperature of severe plastic deformation [ru

  18. The limit of grain refinement on equal channel angular deformation

    International Nuclear Information System (INIS)

    Kopylov, V.I.; Chuvil'deev, V.N.

    2004-01-01

    Experimental and theoretical study results on the process of strain-induced grain refinement under severe plastic deformation are described. A generalization is made for experimental results on deformation dispersing of copper, magnesium and aluminium base alloys as well as unalloyed metals. The model is developed which allows calculating the minimal grain size being able to result from equal channel angular pressing. The expressions describing the dependence of the limit of grain refinement on the nature of the material and severe plastic deformation rate and temperature are obtained [ru

  19. Romanian refining industry assesses restructuring

    International Nuclear Information System (INIS)

    Tanasescu, D.G.

    1991-01-01

    The Romanian crude oil refining industry, as all the other economic sectors, faces the problems accompanying the transition from a centrally planned economy to a market economy. At present, all refineries have registered as joint-stock companies and all are coordinated and assisted by Rafirom S.A., from both a legal and a production point of view. Rafirom S.A. is a joint-stock company that holds shares in refineries and other stock companies with activities related to oil refining. Such activities include technological research, development, design, transportation, storage, and domestic and foreign marketing. This article outlines the market forces that are expected to: drive rationalization and restructuring of refining operations and define the targets toward which the reconfigured refineries should strive

  20. Data refinement for true concurrency

    Directory of Open Access Journals (Sweden)

    Brijesh Dongol

    2013-05-01

    Full Text Available The majority of modern systems exhibit sophisticated concurrent behaviour, where several system components modify and observe the system state with fine-grained atomicity. Many systems (e.g., multi-core processors, real-time controllers also exhibit truly concurrent behaviour, where multiple events can occur simultaneously. This paper presents data refinement defined in terms of an interval-based framework, which includes high-level operators that capture non-deterministic expression evaluation. By modifying the type of an interval, our theory may be specialised to cover data refinement of both discrete and continuous systems. We present an interval-based encoding of forward simulation, then prove that our forward simulation rule is sound with respect to our data refinement definition. A number of rules for decomposing forward simulation proofs over both sequential and parallel composition are developed.

  1. Bauxite Mining and Alumina Refining

    Science.gov (United States)

    Frisch, Neale; Olney, David

    2014-01-01

    Objective: To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Methods: Review article. Results: The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust, alumina dust, and caustic mist in contemporary best-practice bauxite mining and alumina refining operations have not been demonstrated to be associated with clinically significant decrements in lung function. Exposures to bauxite dust and alumina dust at such operations are also not associated with the incidence of cancer. Conclusions: A range of occupational health risks in bauxite mining and alumina refining require the maintenance of effective control measures. PMID:24806720

  2. Influence of titanium–boron additions on grain refinement of AA6082 gas tungsten arc welds

    International Nuclear Information System (INIS)

    Kishore Babu, N.; Talari, Mahesh Kumar; Dayou, Pan; Zheng, Sun; Jun, Wei; SivaPrasad, K.

    2012-01-01

    Highlights: ► Ti in the weld metal resulted in grain refinement due to growth restriction effect. ► Weld metal strength improved due to grain refinement caused by Tibor™ addition. ► Weld metal responded to post-weld ageing treatment due to dilution from base metal. ► Weld metal with AA5356 filler are stronger then AA4043 for all Tibor™ additions. -- Abstract: Grain refinement of weld metal plays a vital role in improving mechanical properties (ductility and toughness) as well as weldability. The present study has investigated the influence of Tibor™ additions on the structure and mechanical properties of AA6082 gas tungsten arc (GTA) weldments. Controlled amounts of Tibor™ grain refiner (containing Ti and B in a ratio of 5:1) were introduced into the molten pool of AA6082 by pre-deposited cast inserts (AA4043 and AA5356) under different welding conditions by GTA welding. Full penetration GTA welds were prepared using alternating current (AC). It was observed that grain size was decreased with increasing amounts of Tibor™. The grain refinement is mainly caused grain nucleation associated with constitutional undercooling during solidification. It has been shown that welds prepared with 5356 cast insert exhibited high strength and ductility when compared with other welds. The observed grain refinement was shown to result in an appreciable increase in fusion zone hardness, strength and ductility.

  3. Refining Nodes and Edges of State Machines

    DEFF Research Database (Denmark)

    Hallerstede, Stefan; Snook, Colin

    2011-01-01

    State machines are hierarchical automata that are widely used to structure complex behavioural specifications. We develop two notions of refinement of state machines, node refinement and edge refinement. We compare the two notions by means of examples and argue that, by adopting simple conventions...... refinement theory and UML-B state machine refinement influences the style of node refinement. Hence we propose a method with direct proof of state machine refinement avoiding the detour via Event-B that is needed by UML-B....

  4. Tangible Asset Management In Real Sector Companies: A Parallel Between Industry Of Crude Oil Refining And Industry Of Refining Of Non Metallic Mineral In Colombia Gerenciamiento de activos tangibles en empresas del sector real: un paralelo entre industria de refinación de crudos e industria de refinación de minerales no metálicos en Colombia

    Directory of Open Access Journals (Sweden)

    John Jairo Forero Romero

    2012-08-01

    sus elementos tomando como referencia dos casos específicos: laRefinería de Barrancabermeja de Ecopetrol S.A. y Sumicol S.A.

  5. Multigrid for refined triangle meshes

    Energy Technology Data Exchange (ETDEWEB)

    Shapira, Yair

    1997-02-01

    A two-level preconditioning method for the solution of (locally) refined finite element schemes using triangle meshes is introduced. In the isotropic SPD case, it is shown that the condition number of the preconditioned stiffness matrix is bounded uniformly for all sufficiently regular triangulations. This is also verified numerically for an isotropic diffusion problem with highly discontinuous coefficients.

  6. Panorama 2007: Refining and Petrochemicals

    International Nuclear Information System (INIS)

    Silva, C.

    2007-01-01

    The year 2005 saw a new improvement in refining margins that continued during the first three quarters of 2006. The restoration of margins in the last three years has allowed the refining sector to regain its profitability. In this context, the oil companies reported earnings for fiscal year 2005 that were up significantly compared to 2004, and the figures for the first half-year 2006 confirm this trend. Despite this favorable business environment, investments only saw a minimal increase in 2005 and the improvement expected for 2006 should remain fairly limited. Looking to 2010-2015, it would appear that the planned investment projects with the highest probability of reaching completion will be barely adequate to cover the increase in demand. Refining sector should continue to find itself under pressure. As for petrochemicals, despite a steady up-trend in the naphtha price, the restoration of margins consolidated a comeback that started in 2005. All in all, capital expenditure remained fairly low in both the refining and petrochemicals sectors, but many projects are planned for the next ten years. (author)

  7. Refining analgesia strategies using lasers.

    Science.gov (United States)

    Hampshire, Victoria

    2015-08-01

    Sound programs for the humane care and use of animals within research facilities incorporate experimental refinements such as multimodal approaches for pain management. These approaches can include non-traditional strategies along with more established ones. The use of lasers for pain relief is growing in popularity among companion animal veterinary practitioners and technologists. Therefore, its application in the research sector warrants closer consideration.

  8. On syntactic action refinement and logic

    OpenAIRE

    Majster-Cederbaum, Mila; Salger, Frank

    1999-01-01

    Action refinement is a useful methodology for the development of concurrent processes in a stepwise manner. We are here interested in establishing a connection between syntactic action refinement and logic. In the syntactic approach to action refinement, reduction functions are used to remove the refinement operators from process-algebraic expressions thereby providing semantics for them. We incorporate a syntactic action refinement operator to the Hennessy-Milner-Logic and define a logical r...

  9. Current research progress in grain refinement of cast magnesium alloys: A review article

    International Nuclear Information System (INIS)

    Ali, Yahia; Qiu, Dong; Jiang, Bin; Pan, Fusheng; Zhang, Ming-Xing

    2015-01-01

    Grain refinement of cast magnesium alloys, particularly in magnesium–aluminium (Mg–Al) based alloys, has been an active research topic in the past two decades, because it has been considered as one of the most effective approaches to simultaneously increase the strength, ductility and formability. The development of new grain refiners was normally based on the theories/models that were established through comprehensive and considerable studies of grain refinement in cast Al alloys. Generally, grain refinement in cast Al can be achieved through either inoculation treatment, which is a process of adding, or in situ forming, foreign particles to promote heterogeneous nucleation rate, or restricting grain growth by controlling the constitutional supercooling or both. But, the concrete and tangible grain refinement mechanism in cast metals is still not fully understood and there are a number of controversies. Therefore, most of the new developed grain refiners for Mg–Al based alloys are not as efficient as the commercially available ones, such as zirconium in non-Al containing Mg alloys. To facilitate the research in grain refinement of cast magnesium alloys, this review starts with highlighting the theoretical aspects of grain refinement in cast metals, followed by reviewing the latest research progress in grain refinement of magnesium alloys in terms of the solute effect and potent nucleants

  10. Grain refinement of AZ31 by (SiC)P: Theoretical calculation and experiment

    International Nuclear Information System (INIS)

    Guenther, R.; Hartig, Ch.; Bormann, R.

    2006-01-01

    Grain refinement of gravity die-cast Mg-alloys can be achieved via two methods: in situ refinement by primary precipitated metallic or intermetallic phases, and inoculation of the melt via ceramic particles that remain stable in the melt due to their high thermodynamic stability. In order to clarify grain refinement mechanisms and optimize possible potent refiners in Mg-alloys, a simulation method for heterogeneous nucleation based on a free growth model has been developed. It allows the prediction of the grain size as a function of the particle size distribution, the volumetric content of ceramic inoculants, the cooling rate and the alloy constitution. The model assumptions were examined experimentally by a study of the grain refinement of (SiC) P in AZ31. Additions of (SiC) P result in significant grain refinement, if appropriate parameters for ceramic particles are chosen. The model makes quantitatively correct predictions for the grain size and its variation with cooling rate

  11. Bauxite Mining and Alumina Refining

    OpenAIRE

    Donoghue, A. Michael; Frisch, Neale; Olney, David

    2014-01-01

    Objective: To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Methods: Review article. Results: The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust,...

  12. The Charfuel coal refining process

    International Nuclear Information System (INIS)

    Meyer, L.G.

    1991-01-01

    The patented Charfuel coal refining process employs fluidized hydrocracking to produce char and liquid products from virtually all types of volatile-containing coals, including low rank coal and lignite. It is not gasification or liquefaction which require the addition of expensive oxygen or hydrogen or the use of extreme heat or pressure. It is not the German pyrolysis process that merely 'cooks' the coal, producing coke and tar-like liquids. Rather, the Charfuel coal refining process involves thermal hydrocracking which results in the rearrangement of hydrogen within the coal molecule to produce a slate of co-products. In the Charfuel process, pulverized coal is rapidly heated in a reducing atmosphere in the presence of internally generated process hydrogen. This hydrogen rearrangement allows refinement of various ranks of coals to produce a pipeline transportable, slurry-type, environmentally clean boiler fuel and a slate of value-added traditional fuel and chemical feedstock co-products. Using coal and oxygen as the only feedstocks, the Charfuel hydrocracking technology economically removes much of the fuel nitrogen, sulfur, and potential air toxics (such as chlorine, mercury, beryllium, etc.) from the coal, resulting in a high heating value, clean burning fuel which can increase power plant efficiency while reducing operating costs. The paper describes the process, its thermal efficiency, its use in power plants, its pipeline transport, co-products, environmental and energy benefits, and economics

  13. Refining's-clean new jingle

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that at a time when profit margins are slim and gasoline demand is down, the U.S. petroleum-refining industry is facing one of its greatest challenges; How to meet new federal and state laws for reformulated gasoline, oxygenated fuels, low-sulfur diesel and other measures to improve the environment. The American Petroleum Institute (API) estimates that industry will spend between $15 and $23 billion by the end of the decade to meet the U.S. Clean Air Act Amendments (CAAA) of 1990, and other legislation. ENSR Consulting and Engineering's capital-spending figure runs to between $70 and 100 billion this decade, including $24 billion to produce reformulated fuels and $10-12 billion to reduce refinery emissions. M.W. Kellogg Co. estimates that refiners may have to spend up to $30 billion this decade to meet the demand for reformulated gasoline. The estimates are wide-ranging because refiners are still studying their options and delaying final decisions as long as they can, to try to ensure they are the best and least-costly decisions. Oxygenated fuels will be required next winter, but federal regulations for reformulated gasoline won't go into effect until 1995, while California's tougher reformulated-fuels law will kick in the following year

  14. Refined topological strings on local ℙ2

    International Nuclear Information System (INIS)

    Iqbal, Amer; Kozçaz, Can

    2017-01-01

    We calculate the refined topological string partition function of the Calabi-Yau threefold which is the total space of the canonical bundle on ℙ 2 (the local ℙ 2 ). The refined topological vertex formalism can not be directly applied to local ℙ 2 therefore we use the properties of the refined Hopf link to define a new two legged vertex which together with the refined vertex gives the partition function of the local ℙ 2 .

  15. Latin American oil markets and refining

    International Nuclear Information System (INIS)

    Yamaguchi, N.D.; Obadia, C.

    1999-01-01

    This paper provides an overview of the oil markets and refining in Argentina, Brazil, Chile, Colombia, Ecuador, Mexico, Peru and Venezuela, and examines the production of crude oil in these countries. Details are given of Latin American refiners highlighting trends in crude distillation unit capacity, cracking to distillation ratios, and refining in the different countries. Latin American oil trade is discussed, and charts are presented illustrating crude production, oil consumption, crude refining capacity, cracking to distillation ratios, and oil imports and exports

  16. Neutron Powder Diffraction and Constrained Refinement

    DEFF Research Database (Denmark)

    Pawley, G. S.; Mackenzie, Gordon A.; Dietrich, O. W.

    1977-01-01

    The first use of a new program, EDINP, is reported. This program allows the constrained refinement of molecules in a crystal structure with neutron diffraction powder data. The structures of p-C6F4Br2 and p-C6F4I2 are determined by packing considerations and then refined with EDINP. Refinement...

  17. The Refined Function-Behaviour-Structure Framework

    NARCIS (Netherlands)

    Diertens, B.

    2013-01-01

    We refine the function-behaviour-structure framework for design introduced by John Gero in order to deal with complexity. We do this by connecting the frameworks for the desing of two models, one the refinement of the other. The result is a refined framework for the design of an object on two levels

  18. Grain refinement of aluminum and its alloys

    International Nuclear Information System (INIS)

    Zaid, A.I.O.

    2001-01-01

    Grain refinement of aluminum and its alloys by the binary Al-Ti and Ternary Al-Ti-B master alloys is reviewed and discussed. The importance of grain refining to the cast industry and the parameters affecting it are presented and discussed. These include parameters related to the cast, parameters related to the grain refining alloy and parameters related to the process. The different mechanisms, suggested in the literature for the process of grain refining are presented and discussed, from which it is found that although the mechanism of refining by the binary Al-Ti is well established the mechanism of grain refining by the ternary Al-Ti-B is still a controversial matter and some research work is still needed in this area. The effect of the addition of other alloying elements in the presence of the grain refiner on the grain refining efficiency is also reviewed and discussed. It is found that some elements e.g. V, Mo, C improves the grain refining efficiency, whereas other elements e.g. Cr, Zr, Ta poisons the grain refinement. Based on the parameters affecting the grain refinement and its mechanism, a criterion for selection of the optimum grain refiner is forwarded and discussed. (author)

  19. On Interaction Refinement in Middleware

    DEFF Research Database (Denmark)

    Truyen, Eddy; Jørgensen, Bo Nørregaard; Joosen, Wouter

    2000-01-01

    Component framework technology has become the cornerstone of building a family of systems and applications. A component framework defines a generic architecture into which specialized components can be plugged. As such, the component framework leverages the glue that connects the different inserted...... components together. We have examined a reflective technique that improve the dynamics of this gluing process such that interaction between components can be refined at run-time. In this paper, we show how we have used this reflective technique to dynamically integrate into the architecture of middleware...

  20. Refining method for bismuth nitrate

    International Nuclear Information System (INIS)

    Shibata, Shigeyuki.

    1997-01-01

    The present invention concerns a method of separating and removing α ray emitting nuclides present in an aqueous solution of bismuth nitrate by an industrially convenient method. A nitric acid concentration in the aqueous solution of bismuth nitrate in which α ray emitting nuclides are dissolved is lowered to coprecipitate the bismuth oxynitrate and the α ray emitting nuclides. The coprecipitation materials are separated from the aqueous solution of bismuth nitrate to separate the α ray emitting nuclides dissolved in the aqueous solution of bismuth nitrate thereby refining the aqueous solution of bismuth nitrate. (T.M.)

  1. W. European refiners face tough environmental rules

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper reports that western Europe's refiners are beginning to grapple with the kind of fundamental changes and huge outlays related to stringent new environmental standards their U.S. counterparts are encountering. Just as the 1990 amendments to the Clean Air Act (CAAA) is transforming the shape of U.S refining and imposing staggering costs on refiners there, new directives proposed by the European Community Commission threaten the same for western European refiners. Given the current state of the industry in Europe, industry officials warn, refiners there might not be able to fund those massive environmental outlays

  2. Niobium-base grain refiner for aluminium

    International Nuclear Information System (INIS)

    Silva Pontes, P. da; Robert, M.H.; Cupini, N.L.

    1980-01-01

    A new chemical grain refiner for aluminium has been developed, using inoculation of a niobium-base compound. When a bath of molten aluminium is inoculated whith this refiner, an intermetallic aluminium-niobium compound is formed which acts as a powerful nucleant, producing extremely fine structure comparable to those obtained by means of the traditional grain refiner based on titanium and boron. It was found that the refinement of the structure depends upon the weight percentage of the new refiner inoculated as well as the time of holding the bath after inoculation and before pouring, but mainly on the inoculating temperature. (Author) [pt

  3. Refined gasoline in the subsurface

    International Nuclear Information System (INIS)

    Bruce, L.G.

    1993-01-01

    Geologists today are being called upon not only to find naturally occurring petroleum, but also to help assess and remediate the problem of refined hydrocarbons and other man-made contaminants in the subsurface that may endanger freshwater resources or human health. Petroleum geologists already have many of the skills required and are at ease working with fluid flow in the subsurface. If called for environmental projects, however, they will need to know the language and additional concepts necessary to deal with the hydrogeologic problems. Most releases of refined hydrocarbons and other man-made contaminants occur in the shallow unconfined groundwater environment. This is divided into three zones: the saturated zone, unsaturated zone, and capillary fringe. All three have unique characteristics, and contamination behaves differently in each. Gasoline contamination partitions into four phases in this environment; vapor phase, residual phase, free phase, and dissolved phase. Each has a different degree of mobility in the three subsurface zones. Their direction and rate of movement can be estimated using basic concepts, but geological complexities frequently complicate this issue. 24 refs., 19 figs., 4 tabs

  4. Study On The Electro-Refining Of Tin In Acid Solution From Electronic Waste

    Directory of Open Access Journals (Sweden)

    Son Seong Ho

    2015-06-01

    Full Text Available The tin metal could be retractable from wasted tin scrap, sludge, and wasted electroplated solution hydrometallurgical treatment, and purification process. In order to be used as resource of electronic devices, the retracted crude metal should be purified to the extent of higher than 99.9%. In this study, tin electro-refining process was performed to purify the casted tin crude metal at various experimental conditions: at the current density of 3, 5A/dm2, and in various electrolytes such as hydrochloric acid, sulfuric acid and methansulfonic acid. Additional experiment was conducted using Rotating Disk Electrode (RDE in order to investigate the rate determining step of tin electro-refining process. The current efficiency, 65.6%, was achievable at the condition of current density, 5A/dm2, and in the electrolyte of Hydrochloric acid. During tin electro-refining process, impurity dissolved from tin crude metal into the electrolyte was analyzed using Inductively Coupled Plasma Optical Emission Spectrometer (ICP-OES, and the result showed the concentration of impurity metal gradually increased. Quantitative analysis on casted tin crude metal showed that it consists of tin with 93.9 wt.% and several impurity metals of Ag, Bi, Pb, Cu, and etc. After tin electro-refining process, the purity of tin increased up to 99.985 wt.%.

  5. Thermal analysis of aluminum alloys as a tool to evaluate the grain refiners efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Hariedy, M.M. [Aluminium Co. of Egypt, Nag Hammadi (Egypt); Niazi, A. [Assiut Univ. (Egypt); Nofal, A.A. [Central Metallurgical Research and Development Inst., Cairo (Egypt)

    1996-10-01

    Al-5%Ti-1%B and Al-5%Ti-1C master alloys were used to grain refine some aluminum alloys. The factors that affect the efficiency of grain refiners (addition rate, holding time, pouring temperature and metal composition) were studied. Thermal analysis was used to evaluate the efficiency of the two grain refiners in parallel with a conventional method (KBI test). The characteristic parameters of the cooling curves have been correlated to the grain size of the castings. It was found that thermal analysis could be used as a tool to evaluate the efficiency of the grain refiners of aluminum alloys prior to casting. Also, it was found that Al-5%Ti-1%C master alloy is more efficient grain refiner than Al-5%Ti-1%B.

  6. Adaptive mesh refinement in titanium

    Energy Technology Data Exchange (ETDEWEB)

    Colella, Phillip; Wen, Tong

    2005-01-21

    In this paper, we evaluate Titanium's usability as a high-level parallel programming language through a case study, where we implement a subset of Chombo's functionality in Titanium. Chombo is a software package applying the Adaptive Mesh Refinement methodology to numerical Partial Differential Equations at the production level. In Chombo, the library approach is used to parallel programming (C++ and Fortran, with MPI), whereas Titanium is a Java dialect designed for high-performance scientific computing. The performance of our implementation is studied and compared with that of Chombo in solving Poisson's equation based on two grid configurations from a real application. Also provided are the counts of lines of code from both sides.

  7. Corrosion problems and solutions in oil refining and petrochemical industry

    CERN Document Server

    Groysman, Alec

    2017-01-01

    This book addresses corrosion problems and their solutions at facilities in the oil refining and petrochemical industry, including cooling water and boiler feed water units. Further, it describes and analyzes corrosion control actions, corrosion monitoring, and corrosion management. Corrosion problems are a perennial issue in the oil refining and petrochemical industry, as they lead to a deterioration of the functional properties of metallic equipment and harm the environment – both of which need to be protected for the sake of current and future generations. Accordingly, this book examines and analyzes typical and atypical corrosion failure cases and their prevention at refineries and petrochemical facilities, including problems with: pipelines, tanks, furnaces, distillation columns, absorbers, heat exchangers, and pumps. In addition, it describes naphthenic acid corrosion, stress corrosion cracking, hydrogen damages, sulfidic corrosion, microbiologically induced corrosion, erosion-corrosion, and corrosion...

  8. The Refining Mechanism of Super Gravity on the Solidification Structure of Al-Cu Alloys

    Directory of Open Access Journals (Sweden)

    Yuhou Yang

    2016-12-01

    Full Text Available There is far less study of the refining effect of super gravity fields on solidification structures of metals than of the effects of electrical currents, magnetic and ultrasonic fields. Moreover, the refining mechanisms of super gravity are far from clear. This study applied a super gravity field to Al-Cu alloys to investigate its effect on refining their structures and the mechanism of interaction. The experimental results showed that the solidification structure of Al-Cu alloys can be greatly refined by a super gravity field. The major refining effect was mainly achieved when super gravity was applied at the initial solidification stage; only slight refinement could be obtained towards the end of solidification. No refinement was obtained by the super gravity treatment on pure liquid or solid stages. The effectiveness of super gravity results from its promoting the multiplication of crystal nuclei, which we call “Heavy Crystal Rain”, thereby greatly strengthening the migration of crystal nuclei within the alloy. Increasing the solute Cu content can increase nucleation density and restrict the growth of crystals, which further increases the refining effect of super gravity. Within this paper, we also discuss the motile behavior of crystals in a field of super gravity.

  9. Refinement: promoting the three Rs in practice.

    Science.gov (United States)

    Lloyd, M H; Foden, B W; Wolfensohn, S E

    2008-07-01

    Refinement of scientific procedures carried out on protected animals is an iterative process, which begins with a critical evaluation of practice. The process continues with objective assessment of the impact of the procedures, identification of areas for improvement, selection and implementation of an improvement strategy and evaluation of the results to determine whether there has been the desired effect, completing the refinement loop and resulting in the perpetuation of good practice. Refinements may be science-driven (those which facilitate getting high-quality results) or welfare-driven or may encompass both groups, but whatever the driver, refinements almost always result in benefits to both welfare and science. Refinements can be implemented in all aspects of animal use: improved methodology in invasive techniques, housing and husbandry, and even statistical analyses can all benefit animal welfare and scientific quality. If refinement is not actively sought, outdated and unnecessarily invasive techniques may not be replaced by better methods as they become available, and thus outdated information is passed down to the next generation, causing perpetuation of old-fashioned methods. This leads to a spiral of ignorance, leading ultimately to poor practice, poor animal welfare and poor-quality scientific data. Refinement is a legal and ethical requirement, yet refinements may not always be implemented. There are numerous obstacles to the implementation of refinement, which may be real or perceived. Either way, in order to take refinement forward, it is important to coordinate the approach to refinement, validate the science behind refinement, ensure there is adequate education and training in new techniques, improve liaison between users and make sure there is feedback on suitability of refinements for use. Overall, refinement requires a coordinated ongoing process of critical appraisal of practice and active scrutiny of resources for likely improvements. In

  10. Weldability of thermally grain-refined Fe-12Ni-0. 25Ti for cryogenic structural applications

    Energy Technology Data Exchange (ETDEWEB)

    Williams, D.E.

    1980-02-01

    The weldability of a research alloy designed for structural use in liquid helium temperature, cryogenic environments was investigated. Plates of iron-12 weight percent nickel-0.25 weight percent titanium were grain refined by the four-step, grain refining thermal treatment developed for this alloy and welded with Inconel Number 92 weld wire using the Gas Metal Arc (GMA) welding process with argon-15% helium gas shielding. Both a single pass and a double-sided, 2 pass electron beam (EB) weld were also made without filler metal addition. Weldments were radiographed and sectioned and the charpy V-notch specimens removed were tested at liquid nitrogen and helium temperatures.

  11. Automated knowledge-base refinement

    Science.gov (United States)

    Mooney, Raymond J.

    1994-01-01

    Over the last several years, we have developed several systems for automatically refining incomplete and incorrect knowledge bases. These systems are given an imperfect rule base and a set of training examples and minimally modify the knowledge base to make it consistent with the examples. One of our most recent systems, FORTE, revises first-order Horn-clause knowledge bases. This system can be viewed as automatically debugging Prolog programs based on examples of correct and incorrect I/O pairs. In fact, we have already used the system to debug simple Prolog programs written by students in a programming language course. FORTE has also been used to automatically induce and revise qualitative models of several continuous dynamic devices from qualitative behavior traces. For example, it has been used to induce and revise a qualitative model of a portion of the Reaction Control System (RCS) of the NASA Space Shuttle. By fitting a correct model of this portion of the RCS to simulated qualitative data from a faulty system, FORTE was also able to correctly diagnose simple faults in this system.

  12. Refining Visually Detected Object poses

    DEFF Research Database (Denmark)

    Holm, Preben; Petersen, Henrik Gordon

    2010-01-01

    Automated industrial assembly today require that the 3D position and orientation (hereafter ''pose`) of the objects to be assembled are known precisely. Today this precision is mostly established by a dedicated mechanical object alignment system. However, such systems are often dedicated to the p......Automated industrial assembly today require that the 3D position and orientation (hereafter ''pose`) of the objects to be assembled are known precisely. Today this precision is mostly established by a dedicated mechanical object alignment system. However, such systems are often dedicated...... to the particular object and in order to handle the demand for flexibility, there is an increasing demand for avoiding such dedicated mechanical alignment systems. Rather, it would be desirable to automatically locate and grasp randomly placed objects from tables, conveyor belts or even bins with a high accuracy...... that enables direct assembly. Conventional vision systems and laser triangulation systems can locate randomly placed known objects (with 3D CAD models available) with some accuracy, but not necessarily a good enough accuracy. In this paper, we present a novel method for refining the pose accuracy of an object...

  13. Comparing Syntactic and Semantics Action Refinement

    NARCIS (Netherlands)

    Goltz, Ursula; Gorrieri, Roberto; Rensink, Arend

    The semantic definition of action refinement on labelled configuration structures is compared with the notion of syntactic substitution, which can be used as another notion of action refinement in a process algebraic setting. The comparison is done by studying a process algebra equipped with

  14. On Syntactic and Semantic Action Refinement

    NARCIS (Netherlands)

    Hagiya, M.; Goltz, U.; Mitchell, J.C.; Gorrieri, R.; Rensink, Arend

    1994-01-01

    The semantic definition of action refinement on labelled event structures is compared with the notion of syntactic substitution, which can be used as another notion of action refinement in a process algebraic setting. This is done by studying a process algebra equipped with the ACP sequential

  15. Anomalies in the refinement of isoleucine

    Energy Technology Data Exchange (ETDEWEB)

    Berntsen, Karen R. M.; Vriend, Gert, E-mail: gerrit.vriend@radboudumc.nl [Radboud University Medical Center, Geert Grooteplein 26-28, 6525 GA Nijmegen (Netherlands)

    2014-04-01

    The side-chain torsion angles of isoleucines in X-ray protein structures are a function of resolution, secondary structure and refinement software. Detailing the standard torsion angles used in refinement software can improve protein structure refinement. A study of isoleucines in protein structures solved using X-ray crystallography revealed a series of systematic trends for the two side-chain torsion angles χ{sub 1} and χ{sub 2} dependent on the resolution, secondary structure and refinement software used. The average torsion angles for the nine rotamers were similar in high-resolution structures solved using either the REFMAC, CNS or PHENIX software. However, at low resolution these programs often refine towards somewhat different χ{sub 1} and χ{sub 2} values. Small systematic differences can be observed between refinement software that uses molecular dynamics-type energy terms (for example CNS) and software that does not use these terms (for example REFMAC). Detailing the standard torsion angles used in refinement software can improve the refinement of protein structures. The target values in the molecular dynamics-type energy functions can also be improved.

  16. Refinement Checking on Parametric Modal Transition Systems

    DEFF Research Database (Denmark)

    Benes, Nikola; Kretínsky, Jan; Larsen, Kim Guldstrand

    2015-01-01

    Modal transition systems (MTS) is a well-studied specification formalism of reactive systems supporting a step-wise refinement methodology. Despite its many advantages, the formalism as well as its currently known extensions are incapable of expressing some practically needed aspects in the refin...

  17. Refined large N duality for knots

    DEFF Research Database (Denmark)

    Kameyama, Masaya; Nawata, Satoshi

    We formulate large N duality of U(N) refined Chern-Simons theory with a torus knot/link in S³. By studying refined BPS states in M-theory, we provide the explicit form of low-energy effective actions of Type IIA string theory with D4-branes on the Ω-background. This form enables us to relate...

  18. Grain refinement of zinc-aluminium alloys

    International Nuclear Information System (INIS)

    Zaid, A.I.O.

    2006-01-01

    It is now well-established that the structure of the zinc-aluminum die casting alloys can be modified by the binary Al-Ti or the ternary Al-Ti-B master alloys. in this paper, grain refinement of zinc-aluminum alloys by rare earth materials is reviewed and discussed. The importance of grain refining of these alloys and parameters affecting it are presented and discussed. These include parameters related to the Zn-Al alloys cast, parameters related to the grain refining elements or alloys and parameters related to the process. The effect of addition of other alloying elements e.g. Zr either alone or in the presence of the main grain refiners Ti or Ti + B on the grain refining efficiency is also reviewed and discussed. Furthermore, based on the grain refinement and the parameters affecting it, a criterion for selection of the optimum grain refiner is suggested. Finally, the recent research work on the effect of grain refiners on the mechanical behaviour, impact strength, wear resistance, and fatigue life of these alloys are presented and discussed. (author)

  19. Anomalies in the refinement of isoleucine

    International Nuclear Information System (INIS)

    Berntsen, Karen R. M.; Vriend, Gert

    2014-01-01

    The side-chain torsion angles of isoleucines in X-ray protein structures are a function of resolution, secondary structure and refinement software. Detailing the standard torsion angles used in refinement software can improve protein structure refinement. A study of isoleucines in protein structures solved using X-ray crystallography revealed a series of systematic trends for the two side-chain torsion angles χ 1 and χ 2 dependent on the resolution, secondary structure and refinement software used. The average torsion angles for the nine rotamers were similar in high-resolution structures solved using either the REFMAC, CNS or PHENIX software. However, at low resolution these programs often refine towards somewhat different χ 1 and χ 2 values. Small systematic differences can be observed between refinement software that uses molecular dynamics-type energy terms (for example CNS) and software that does not use these terms (for example REFMAC). Detailing the standard torsion angles used in refinement software can improve the refinement of protein structures. The target values in the molecular dynamics-type energy functions can also be improved

  20. Wrinkling prediction with adaptive mesh refinement

    NARCIS (Netherlands)

    Selman, A.; Meinders, Vincent T.; van den Boogaard, Antonius H.; Huetink, Han

    2000-01-01

    An adaptive mesh refinement procedure for wrinkling prediction analyses is presented. First the critical values are determined using Hutchinson’s bifurcation functional. A wrinkling risk factor is then defined and used to determined areas of potential wrinkling risk. Finally, a mesh refinement is

  1. Zone refining of cadmium and related characterization

    Indian Academy of Sciences (India)

    We present the zone refining results of cadmium using horizontal resistive zone refiner under constant flow of moisture free hydrogen gas. The boron impurity in cadmium can be avoided using quartz (GE 214 grade) boat in lieu of high pure graphite boat. The analytical results using inductively coupled plasma optical ...

  2. Studies on the sedimentation and agglomeration behavior of Al-Ti-B and Al-Ti-C grain refiners

    Energy Technology Data Exchange (ETDEWEB)

    Gazanion, F.; Chen, X.G.; Dupuis, C. [Alcan International Ltd., Jonquiere, PQ (Canada). Arvida Research and Development Centre

    2002-07-01

    The sedimentation and agglomeration behavior of Al-Ti-B and Al-Ti-C grain refiners in liquid aluminum has been investigated using the LiMCA and PoDFA analysis techniques in combination with metallographic examination. The widely used Al-5%Ti-1%B and Al-3%Ti-0.15%C master alloys were chosen. Two aluminum alloys, an AAlxxx (commercially pure metal) and an AA5182 (Al-4.5%Mg) alloy, were prepared with different additions of grain refiners. The difference in particle behavior in liquid aluminum for both refiners is described and briefly analyzed in terms of sensitivity to agglomeration and grain refiner performance. Experimental results indicate that, in comparison with the Al-Ti-B refiner, the Al-Ti-C refiner is detrimentally affected by long holding periods due to the decomposition of TiC particles within the melt. (orig.)

  3. Refined Phenotyping of Modic Changes

    Science.gov (United States)

    Määttä, Juhani H.; Karppinen, Jaro; Paananen, Markus; Bow, Cora; Luk, Keith D.K.; Cheung, Kenneth M.C.; Samartzis, Dino

    2016-01-01

    Abstract Low back pain (LBP) is the world's most disabling condition. Modic changes (MC) are vertebral bone marrow changes adjacent to the endplates as noted on magnetic resonance imaging. The associations of specific MC types and patterns with prolonged, severe LBP and disability remain speculative. This study assessed the relationship of prolonged, severe LBP and back-related disability, with the presence and morphology of lumbar MC in a large cross-sectional population-based study of Southern Chinese. We addressed the topographical and morphological dimensions of MC along with other magnetic resonance imaging phenotypes (eg, disc degeneration and displacement) on the basis of axial T1 and sagittal T2-weighted imaging of L1-S1. Prolonged severe LBP was defined as LBP lasting ≥30 days during the past year, and a visual analog scale severest pain intensity of at least 6/10. An Oswestry Disability Index score of 15% was regarded as significant disability. We also assessed subject demographics, occupation, and lifestyle factors. In total, 1142 subjects (63% females, mean age 53 years) were assessed. Of these, 282 (24.7%) had MC (7.1% type I, 17.6% type II). MC subjects were older (P = 0.003), had more frequent disc displacements (P disability. The strength of the associations increased with the number of MC. This large-scale study is the first to definitively note MC types and specific morphologies to be independently associated with prolonged severe LBP and back-related disability. This proposed refined MC phenotype may have direct implications in clinical decision-making as to the development and management of LBP. Understanding of these imaging biomarkers can lead to new preventative and personalized therapeutics related to LBP. PMID:27258491

  4. North Dakota Refining Capacity Study

    Energy Technology Data Exchange (ETDEWEB)

    Dennis Hill; Kurt Swenson; Carl Tuura; Jim Simon; Robert Vermette; Gilberto Marcha; Steve Kelly; David Wells; Ed Palmer; Kuo Yu; Tram Nguyen; Juliam Migliavacca

    2011-01-05

    According to a 2008 report issued by the United States Geological Survey, North Dakota and Montana have an estimated 3.0 to 4.3 billion barrels of undiscovered, technically recoverable oil in an area known as the Bakken Formation. With the size and remoteness of the discovery, the question became 'can a business case be made for increasing refining capacity in North Dakota?' And, if so what is the impact to existing players in the region. To answer the question, a study committee comprised of leaders in the region's petroleum industry were brought together to define the scope of the study, hire a consulting firm and oversee the study. The study committee met frequently to provide input on the findings and modify the course of the study, as needed. The study concluded that the Petroleum Area Defense District II (PADD II) has an oversupply of gasoline. With that in mind, a niche market, naphtha, was identified. Naphtha is used as a diluent used for pipelining the bitumen (heavy crude) from Canada to crude markets. The study predicted there will continue to be an increase in the demand for naphtha through 2030. The study estimated the optimal configuration for the refinery at 34,000 barrels per day (BPD) producing 15,000 BPD of naphtha and a 52 percent refinery charge for jet and diesel yield. The financial modeling assumed the sponsor of a refinery would invest its own capital to pay for construction costs. With this assumption, the internal rate of return is 9.2 percent which is not sufficient to attract traditional investment given the risk factor of the project. With that in mind, those interested in pursuing this niche market will need to identify incentives to improve the rate of return.

  5. Microstructural characterization and grain refinement of AA6082 gas tungsten arc welds by scandium modified fillers

    Energy Technology Data Exchange (ETDEWEB)

    Babu, N. Kishore, E-mail: nkishorebabu@gmail.com [Joining Technology Group, Singapore Institute of Manufacturing Technology, 71 Nanyang Drive, Singapore 638075 (Singapore); Talari, Mahesh Kumar [Faculty of Applied Sciences, Universiti Teknologi MARA, 40450 Shah Alam (Malaysia); Pan, D.; Sun, Z.; Wei, J. [Joining Technology Group, Singapore Institute of Manufacturing Technology, 71 Nanyang Drive, Singapore 638075 (Singapore); Sivaprasad, K. [Advanced Materials Processing Laboratory, Department of Metallurgical and Materials Engineering, National Institute of Technology, Tiruchirapalli 620015, Tamil Nadu (India)

    2012-12-14

    The refinement in weld metal grain size and shape results in both improved mechanical properties (ductility and toughness) as well as a significant improvement in weldability. In the present study, the influence of scandium (Sc) additions to the fillers on the structure and mechanical properties of AA6082 gas tungsten arc (GTA) weldments were investigated. Controlled amounts of scandium as grain refiner were introduced into the molten pool of AA6082 by pre-deposited cast inserts (AA4043 and AA5356) by GTA welding. Full penetration GTA welds were prepared using alternating current (AC). It was observed that grain size decreased with increasing amounts of scandium. The grain refinement is mainly caused by the Al{sub 3}Sc particles, which act as heterogeneous nucleation of {alpha}-Al grains. It has been shown that welds prepared with AA5356 cast insert exhibited high strength and ductility when compared with other welds. The observed grain refinement was shown to result in an appreciable increase in fusion zone hardness, strength and ductility. Post-weld aging treatment resulted in improved tensile strength and hardness of the weldments and this aging response could be attributed to the weld dilution from the base metal. The slow diffusion of Sc in Al matrix and stability of Al{sub 3}Sc precipitates at elevated temperatures were suggested to be responsible for the improved high temperature yield strength of welds made from Sc modified fillers. -- Highlights: Black-Right-Pointing-Pointer Primary Al{sub 3}Sc particles resulted in grain refinement by heterogeneous nucleation. Black-Right-Pointing-Pointer Weld metal strength and hardness improved due to grain refinement caused by Sc. Black-Right-Pointing-Pointer Weld metal responded to post-weld aging treatment due to dilution from base metal. Black-Right-Pointing-Pointer Sc addition improved the high temperature mechanical properties of welds.

  6. Grain refinement of Aluminium alloys using friction stir processing

    International Nuclear Information System (INIS)

    Khraisheh, M.

    2004-01-01

    Full text.Friction Stir Processing (FSP) is a new advanced material processing technique used to refine and homogenize the microstructure of sheet metals. FSP is a solid state processing technique that uses a rapidly rotating non-consumable high strength tool steel pin that extends from a cylindrical shoulder. The rotating pin is forced with a predetermined load into the work piece and moved along with the work pieces, while the rotating pin deforms and stirs the locally heated material. It is a hot working process in which a large amount of deformation is imparted to the sheet. FS processed zone is characterized by dynamic recrystallization which results in grain refinement . this promising emerging process needs further investigations to develop optimum process parameters to produce the desired microstructure. In this work, we present preliminary results on the effects of rotational and translational speeds on grain refinement of AA5052. Under certain processing conditions, sub-micron grain structure was produced using this technique

  7. Development and evaluation of Al-Ti-C master alloys as grain refiner for aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Hadia, M.A. [Aluminum Co. of Egypt, Nag Hammadi (Egypt); Ghaneya, A.A.; Niazi, A. [Assiut Univ. (Egypt)

    1996-10-01

    A series of Al-Ti-C master alloys with different amounts of titanium and carbon (Al-3.5%Ti-0.5%C, Al-3.5%Ti-0.7%C and Al-5%Ti-1%C) has been developed by adding activated graphite to molten Al-Ti binary alloys. The micro-structures of the developed alloys were investigated. The efficiency of the produced alloys as aluminum grain refiner was evaluated. The effects of the following factors were investigated: addition rate of each master alloy, the pouring temperature of the refined metal and the holding time before pouring. Also, the contact time for each refiner was studied. The results were significant and the refiner Al-5%Ti-1%C was the most effective.

  8. Effect of some grain refiners on the mechanical properties of aluminum

    International Nuclear Information System (INIS)

    Zaid, A.I.O.

    2001-01-01

    It is well established that aluminum and its alloys are grain refined by some refractory metals to enhance their surface qualities and mechanical strengths. In this paper, the literature on grain refining, and its mechanism is reviewed and discussed. Also, the effect of grain refining of commercially pure aluminum by the addition of titanium, boron, vanadium, molybdenum, and zirconium is investigated. The effect of each of these elements on grain size, hardness and mechanical behavior is presented and discussed. It was found that the addition of any of these elements except zirconium resulted in enhancement of grain size, hardness and mechanical strength. An increase of 2.1 % in flow stress of Al grain refined by Ti+B was achieved by addition of 0.1 % V at 0.2 strain. (author)

  9. The Influence of Grain Refiners on the Efficiency of Ceramic Foam Filters

    Science.gov (United States)

    Towsey, Nicholas; Schneider, Wolfgang; Krug, Hans-Peter; Hardman, Angela; Keegan, Neil J.

    An extensive program of work has been carried out to evaluate the efficiency of ceramic foam filters under carefully controlled conditions. Work reported at previous TMS meetings showed that in the absence of grain refiners, ceramic foam filters have the capacity for high filtration efficiency and consistent, reliable performance. The current phase of the investigation focuses on the impact grain refiner additions have on filter performance. The high filtration efficiencies obtained using 50 or 80ppi CFF's in the absence of grain refiners diminish when Al-3%Ti-1%B grain refiners are added. This, together with the impact of incoming inclusion loading on filter performance and the level of grain refiner addition are considered in detail. The new generation Al-3%Ti-0.15%C grain refiner has also been included. At typical addition levels (1kg/tonne) the effect on filter efficiency is similar to that for TiB2based grain refiners. The work was again conducted on a production scale using AA1050 alloy. Metal quality was determined using LiMCA and PoDFA. Spent filters were also analysed.

  10. Protein NMR structures refined without NOE data.

    Science.gov (United States)

    Ryu, Hyojung; Kim, Tae-Rae; Ahn, SeonJoo; Ji, Sunyoung; Lee, Jinhyuk

    2014-01-01

    The refinement of low-quality structures is an important challenge in protein structure prediction. Many studies have been conducted on protein structure refinement; the refinement of structures derived from NMR spectroscopy has been especially intensively studied. In this study, we generated flat-bottom distance potential instead of NOE data because NOE data have ambiguity and uncertainty. The potential was derived from distance information from given structures and prevented structural dislocation during the refinement process. A simulated annealing protocol was used to minimize the potential energy of the structure. The protocol was tested on 134 NMR structures in the Protein Data Bank (PDB) that also have X-ray structures. Among them, 50 structures were used as a training set to find the optimal "width" parameter in the flat-bottom distance potential functions. In the validation set (the other 84 structures), most of the 12 quality assessment scores of the refined structures were significantly improved (total score increased from 1.215 to 2.044). Moreover, the secondary structure similarity of the refined structure was improved over that of the original structure. Finally, we demonstrate that the combination of two energy potentials, statistical torsion angle potential (STAP) and the flat-bottom distance potential, can drive the refinement of NMR structures.

  11. Price implications for Russia's oil refining

    International Nuclear Information System (INIS)

    Khartukov, Eugene M.

    1998-01-01

    Over the past several years, Russia's oil industry has undergone its radical transformation from a wholly state-run and generously subsidized oil distribution system toward a substantially privatized, cash-strapped, and quasi-market ''petropreneurship''. This fully applies to the industry's downstream sector. Still unlike more dynamic E and C operations, the country's refining has turned out better fenced off competitive market forces and is less capable to respond to market imperatives. Consequently, jammed between depressed product prices and persistent feedstock costs, Russian refiners were badly hit by the world oil glut - which has made a radical modernization of the obsolete refining sector clearly a must. (author)

  12. Purification of uranium metal

    International Nuclear Information System (INIS)

    Suzuki, Kenji; Shikama, Tatsuo; Ochiai, Akira.

    1993-01-01

    We developed the system for purifying uranium metal and its metallic compounds and for growing highly pure uranium compounds to study their intrinsic physical properties. Uranium metal was zone refined under low contamination conditions as far as possible. The degree of the purity of uranium metal was examined by the conventional electrical resistivity measurement and by the chemical analysis using the inductive coupled plasma emission spectrometry (ICP). The results show that some metallic impurities evaporated by the r.f. heating and other usual metallic impurities moved to the end of a rod with a molten zone. Therefore, we conclude that the zone refining technique is much effective to the removal of metallic impurities and we obtained high purified uranium metal of 99.99% up with regarding to metallic impurities. The maximum residual resistivity ratio, the r.r.r., so far obtained was about 17-20. Using the purified uranium, we are attempting to grow a highly pure uranium-titanium single crystals. (author)

  13. Development of a Refined Staff Group Trainer

    National Research Council Canada - National Science Library

    Quensel, Susan

    1999-01-01

    .... As a follow-on effort to the previous SGT project, the goal was to refine a brigade-level staff training program to more effectively and efficiently coordinate the activities within and between the...

  14. A Refinement Method for Java Programs

    OpenAIRE

    Grandy, Holger; Stenzel, Kurt; Reif, Wolfgang (Prof. Dr.)

    2006-01-01

    We present a refinement method for Java programs which is motivated by the challenge of verifying security protocol implementations. The method can be used for stepwise refinement of abstract specifications down to the level of code running in the real application. The approach is based on a calculus for the verification of Java programs for the concrete level and Abstract State Machines for the abstract level. In this paper we illustrate our approach with the verification of a MCommerce appl...

  15. Structure refinement from precession electron diffraction data.

    Science.gov (United States)

    Palatinus, Lukáš; Jacob, Damien; Cuvillier, Priscille; Klementová, Mariana; Sinkler, Wharton; Marks, Laurence D

    2013-03-01

    Electron diffraction is a unique tool for analysing the crystal structures of very small crystals. In particular, precession electron diffraction has been shown to be a useful method for ab initio structure solution. In this work it is demonstrated that precession electron diffraction data can also be successfully used for structure refinement, if the dynamical theory of diffraction is used for the calculation of diffracted intensities. The method is demonstrated on data from three materials - silicon, orthopyroxene (Mg,Fe)(2)Si(2)O(6) and gallium-indium tin oxide (Ga,In)(4)Sn(2)O(10). In particular, it is shown that atomic occupancies of mixed crystallographic sites can be refined to an accuracy approaching X-ray or neutron diffraction methods. In comparison with conventional electron diffraction data, the refinement against precession diffraction data yields significantly lower figures of merit, higher accuracy of refined parameters, much broader radii of convergence, especially for the thickness and orientation of the sample, and significantly reduced correlations between the structure parameters. The full dynamical refinement is compared with refinement using kinematical and two-beam approximations, and is shown to be superior to the latter two.

  16. Design of Grain Refiners for Aluminium Alloys

    Science.gov (United States)

    Tronche, A.; Greer, A. L.

    The efficiency of a grain refiner can be quantified as the number of grains per nucleant particle in the solidified product. Even for effective refiners in aluminium, such as Al-5Ti-1B, it is known from experiments that efficiencies are very low, at best 10-3 to 102. It is of interest to explore the reasons for such low values, and to assess the prospects for increased efficiency though design of refiners. Recently it has been shown [1] that a simple recalescence-based model can make quantitative predictions of grain size as a function of refiner addition level, cooling rate and solute content. In the model, the initiation of grains is limited by the free growth from nucleant particles, the size distribution of which is very important. The present work uses this model as the basis for discussing the effect of particle size distribution on grain refiner performance. Larger particles (of TiB2 in the case of present interest) promote greater efficiency, as do narrower size distributions. It is shown that even if the size distribution could be exactly specified, compromises would have to be made to balance efficiency (defined as above) with other desirable characteristics of a refiner.

  17. Future trends in the refining catalyst market

    International Nuclear Information System (INIS)

    Silvy, Ricardo Prada

    2004-01-01

    The oil refining industry operation is analyzed in order to estimate the future catalyst market trends. The refining catalyst market corresponding to the main catalytic processes is estimated taking into account the following information: (1) the average refining capacity increases for the main catalytic processes since 1999, (2) the additional refining capacity due to future plans of construction and expansion of refineries and process units that will be added by 2005, and (3) the past refining catalyst market behavior. From this information, we have determined for the main catalytic processes a global average factor, expressed as processed oil barrels per dollar of catalyst. According to our estimates, the global refining catalyst market will increase from $2.32 billion in 2001 to about $2.65 billion in 2005 (3.6% annual growth). Hydrotreating, fluid catalytic cracking, hydrocracking and isomerization represent about 74% of the total catalyst market and will grow by about $34, $32, $11 and $2.5 million per year, respectively. However, naphtha reforming catalyst market will not grow during 2001-2005. Higher catalyst spending growth is expected for the North America region ($27.5 million per year)

  18. Gravimetric and volumetric determination of the purity of electrolytically refined silver and the produced silver nitrate

    Directory of Open Access Journals (Sweden)

    Ačanski Marijana M.

    2007-01-01

    Full Text Available Silver is, along with gold and the platinum-group metals, one of the so called precious metals. Because of its comparative scarcity, brilliant white color, malleability and resistance to atmospheric oxidation, silver has been used in the manufacture of coins and jewelry for a long time. Silver has the highest known electrical and thermal conductivity of all metals and is used in fabricating printed electrical circuits, and also as a coating for electronic conductors. It is also alloyed with other elements such as nickel or palladium for use in electrical contacts. The most useful silver salt is silver nitrate, a caustic chemical reagent, significant as an antiseptic and as a reagent in analytical chemistry. Pure silver nitrate is an intermediate in the industrial preparation of other silver salts, including the colloidal silver compounds used in medicine and the silver halides incorporated into photographic emulsions. Silver halides become increasingly insoluble in the series: AgCl, AgBr, AgI. All silver salts are sensitive to light and are used in photographic coatings on film and paper. The ZORKA-PHARMA company (Sabac, Serbia specializes in the production of pharmaceutical remedies and lab chemicals. One of its products is chemical silver nitrate (argentum-nitricum (l. Silver nitrate is generally produced by dissolving pure electrolytically refined silver in hot 48% nitric acid. Since the purity of silver nitrate, produced in 2002, was not in compliance with the p.a. level of purity, there was doubt that the electrolytically refined silver was pure. The aim of this research was the gravimetric and volumetric determination of the purity of electrolytically refined silver and silver nitrate, produced industrially and in a laboratory. The purity determination was carried out gravimetrically, by the sedimentation of silver(I ions in the form of insoluble silver salts: AgCl, AgBr and Agi, and volumetrically, according to Mohr and Volhardt. The

  19. Concurrent reduction and distillation: an improved technique for the recovery and chemical refinement of the isotopes of cadmium and zinc

    International Nuclear Information System (INIS)

    Caudill, H.H.; McBride, L.E.; McDaniel, E.W.

    1982-01-01

    The Electromagnetic Isotope Separations Program of the Oak Ridge National Laboratory has been involved in the separation, chemical recovery, and refinement of the stable isotopes of cadmium and zinc since 1946. Traditionally, the chemical refinement procedures for these elements consisted of ion exchange separations using anion exchange resins followed by pH-controlled hydrogen sulfide precipitations. The procedures were quite time-consuming and made it difficult to remove trace quantities of sulfur which interferes in subsequent attempts to prepare rolled metal foils. As demands for 113 Cd and 68 Zn (a precursor for the production of the radiopharmaceutical 67 Ga) increased, it became evident that a quicker, more efficient refinement procedure was needed. Details of an improved method, which employs concurrent hydrogen reduction and distillation in the recovery and refinement of isotopically enriched zinc, are described. Modifications of the procedure suitable for the refinement of cadmium isotopes are also described. 3 figures, 1 table

  20. Grain refining of Al-4.5Cu alloy by adding an Al-30TiC master alloy

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Kazuaki [Toyota Motor Corp., Shizuoka (Japan). Materials Engineering Div. III; Flemings, M.C. [Massachusetts Inst. of Tech., Cambridge, MA (United States). Dept. of Materials Science and Engineering

    1998-06-01

    A particulate Al-30 wt pct TiC composite was employed as a grain refiner for the Al-4.5 wt pct Cu alloy. The composite contains submicron TiC particles. The addition of the TiC grain refiner to the metal alloy in the amount of 0.1 Ti wt pct effected a remarkable reduction in the average grain size in Al-4.5 wt pct Cu alloy castings. With the content of over 0.2 Ti wt pct, the grain refiner maintained its refining effectiveness even after a 3,600-second holding time at 973 K. The TiC particles in the resulting castings were free of interfacial phases. It is concluded that the TiC are the nucleating agents and that they are resistant to the fading effect encountered with most grain refiners.

  1. Grain refinement mechanism in A3003 alloy

    International Nuclear Information System (INIS)

    Cho, Hoon; Shin, Je-Sik; Lee, Byoung-Soo; Jo, Hyung-Ho

    2009-01-01

    In the present study, in order to find out an grain refinement mechanism, 0.1wt.% Al-10wt.%Ti master alloy was added into A3003 alloy melt contained in graphite crucible and in alumina crucible, and then the melt holding time at 750 deg. C was systematically changed from 1 min up to 120 min. It is interesting to note that the grain refinement and fading phenomena remarkably depend on the crucible material. The fading effect in the specimens using alumina crucible can be explained as the result of TiAl 3 phase dissolution into molten aluminium matrix. In the specimens using graphite crucible, the grain refinement was occurred gradually with increasing holding time. It was suggest that the continuous grain refinement is due to transition of refinement mechanism from TiAl 3 phase to TiC phase. It can be mentioned that the TiC formed from titanium and carbon solute in the aluminium melt, which came from the Al-10Ti alloy and the graphite crucible.

  2. Proceedings of the DGMK-conference 'Chances for innovative processes at the interface between refining and petrochemistry'. Authors' manuscripts

    Energy Technology Data Exchange (ETDEWEB)

    Emig, G.; Gallei, E.; Luecke, B.; Weitkamp, J. (eds.)

    2002-07-01

    The latest developments in the field of petrochemical refining are reviewed in 37 papers. Main topics are catalysts developments for various chemical reactions, ionic liquids, zeolite and metal catalysts. (uke)

  3. Model refinement for offshore platforms: Experimental study

    Science.gov (United States)

    Zhang, Min; Chen, Zongli; Wu, Yanjian

    2017-08-01

    Offshore jacket platforms are widely used in offshore oil and gas exploitation. Finite element models of such structures need to have many degrees of freedom (DOFs) to represent the geometrical detail of complex structures, thereby leading to incompatibility in the number of DOFs of experimental models. To bring them both to the same order while ensuring that the essential eigen- properties of the refined model match those of experimental models, an extended model refinement procedure is presented in this paper. Vibration testing of an offshore jacket platform model is performed to validate the applicability of the proposed approach. A full-order finite element model of the platform is established and then tuned to meet the measured modal properties identified from the acceleration signals. Both model reduction and modal expansion methods are investigated, as well as various scenarios of sensor arrangements. Upon completion of the refinement, the updated jacket platform model matches the natural frequencies of the measured model well.

  4. India's refining prospects linked to economic growth

    International Nuclear Information System (INIS)

    Lewis, E.

    1996-01-01

    International investors assess refining ventures in India the same way they do comparable projects elsewhere in the world: according to their expectations about investment returns. By that standard, India's appeal is mixed, although its need for some measure of additional refining capacity seems certain. The success of future refinery investments will depend heavily on the government's commitment to policies allowing the economy to grow faster than the population. Unless accompanied by economic growth, expected increases in the population will not automatically raise demand for petroleum products. Decisions about investments in India's refining sector, therefore, must carefully weigh market fundamentals, the business environment, and likely investment performance. This paper reviews the market for the various products and predicts new economic trends

  5. Refining Linear Fuzzy Rules by Reinforcement Learning

    Science.gov (United States)

    Berenji, Hamid R.; Khedkar, Pratap S.; Malkani, Anil

    1996-01-01

    Linear fuzzy rules are increasingly being used in the development of fuzzy logic systems. Radial basis functions have also been used in the antecedents of the rules for clustering in product space which can automatically generate a set of linear fuzzy rules from an input/output data set. Manual methods are usually used in refining these rules. This paper presents a method for refining the parameters of these rules using reinforcement learning which can be applied in domains where supervised input-output data is not available and reinforcements are received only after a long sequence of actions. This is shown for a generalization of radial basis functions. The formation of fuzzy rules from data and their automatic refinement is an important step in closing the gap between the application of reinforcement learning methods in the domains where only some limited input-output data is available.

  6. Using supercritical fluids to refine hydrocarbons

    Science.gov (United States)

    Yarbro, Stephen Lee

    2015-06-09

    A system and method for reactively refining hydrocarbons, such as heavy oils with API gravities of less than 20 degrees and bitumen-like hydrocarbons with viscosities greater than 1000 cp at standard temperature and pressure, using a selected fluid at supercritical conditions. A reaction portion of the system and method delivers lightweight, volatile hydrocarbons to an associated contacting unit which operates in mixed subcritical/supercritical or supercritical modes. Using thermal diffusion, multiphase contact, or a momentum generating pressure gradient, the contacting unit separates the reaction products into portions that are viable for use or sale without further conventional refining and hydro-processing techniques.

  7. Contextual Distance Refining for Image Retrieval

    KAUST Repository

    Islam, Almasri

    2014-09-16

    Recently, a number of methods have been proposed to improve image retrieval accuracy by capturing context information. These methods try to compensate for the fact that a visually less similar image might be more relevant because it depicts the same object. We propose a new quick method for refining any pairwise distance metric, it works by iteratively discovering the object in the image from the most similar images, and then refine the distance metric accordingly. Test show that our technique improves over the state of art in terms of accuracy over the MPEG7 dataset.

  8. India beckons participants in burgeoning refining sector

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that India has opened its refining sector to full private investment for the first time in more than 2 decades. The government again gave a green light to construction of three 120,000 b/d grassroots refineries in East, West, and Central India. The projects had won various governmental approvals in the past few years, but never moved off high center for a variety of economic and regulatory reasons. The difference this time is that the government is offering interests in the projects to private foreign and domestic investors. It's part of India's push to boost overall refining capacity by more than 80% this century

  9. Zone refining high-purity germanium

    International Nuclear Information System (INIS)

    Hubbard, G.S.; Haller, E.E.; Hansen, W.L.

    1977-10-01

    The effects of various parameters on germanium purification by zone refining have been examined. These parameters include the germanium container and container coatings, ambient gas and other operating conditions. Four methods of refining are presented which reproducibly yield 3.5 kg germanium ingots from which high purity (vertical barN/sub A/ - N/sub D/vertical bar less than or equal to2 x 10 10 cm -3 ) single crystals can be grown. A qualitative model involving binary and ternary complexes of Si, O, B, and Al is shown to account for the behavior of impurities at these low concentrations

  10. Refining - Panorama 2008; Raffinage - Panorama 2008

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    Investment rallied in 2007, and many distillation and conversion projects likely to reach the industrial stage were announced. With economic growth sustained in 2006 and still pronounced in 2007, oil demand remained strong - especially in emerging countries - and refining margins stayed high. Despite these favorable business conditions, tensions persisted in the refining sector, which has fallen far behind in terms of investing in refinery capacity. It will take renewed efforts over a long period to catch up. Looking at recent events that have affected the economy in many countries (e.g. the sub-prime crisis), prudence remains advisable.

  11. Adaptive mesh refinement for storm surge

    KAUST Repository

    Mandli, Kyle T.

    2014-03-01

    An approach to utilizing adaptive mesh refinement algorithms for storm surge modeling is proposed. Currently numerical models exist that can resolve the details of coastal regions but are often too costly to be run in an ensemble forecasting framework without significant computing resources. The application of adaptive mesh refinement algorithms substantially lowers the computational cost of a storm surge model run while retaining much of the desired coastal resolution. The approach presented is implemented in the GeoClaw framework and compared to ADCIRC for Hurricane Ike along with observed tide gauge data and the computational cost of each model run. © 2014 Elsevier Ltd.

  12. Computing Refined Buneman Trees in Cubic Time

    DEFF Research Database (Denmark)

    Brodal, G.S.; Fagerberg, R.; Östlin, A.

    2003-01-01

    in the underlying distance data. Distance based methods based on the theory of Buneman trees and refined Buneman trees avoid this problem by only proposing evolutionary trees whose edges satisfy a number of constraints. These trees might not be fully resolved but there is strong combinatorial evidence for each...... proposed edge. The currently best algorithm for computing the refined Buneman tree from a given distance measure has a running time of O(n 5) and a space consumption of O(n 4). In this paper, we present an algorithm with running time O(n 3) and space consumption O(n 2). The improved complexity of our...

  13. Image segmentation by background extraction refinements

    Science.gov (United States)

    Rodriguez, Arturo A.; Mitchell, O. Robert

    1990-01-01

    An image segmentation method refining background extraction in two phases is presented. In the first phase, the method detects homogeneous-background blocks and estimates the local background to be extracted throughout the image. A block is classified homogeneous if its left and right standard deviations are small. The second phase of the method refines background extraction in nonhomogeneous blocks by recomputing the shoulder thresholds. Rules that predict the final background extraction are derived by observing the behavior of successive background statistical measurements in the regions under the presence of dark and/or bright object pixels. Good results are shown for a number of outdoor scenes.

  14. Pilot scale refinning of crude soybean oil | Mensah | Journal of ...

    African Journals Online (AJOL)

    Pilot scale refinning of crude soybean oil. ... Abstract. A laboratory process for refining soybean has been scaled up to a 145 tonne per annum pilot plant to refine crude soybean oil. ... The quality of the refined oil was found to be within national and codex standard specifications for edible oil from vegetable sources.

  15. Refining and new analysis of W18O49 structure

    International Nuclear Information System (INIS)

    Lamire, M.; Labbe, P.; Goreaud, M.; Raveau, B.

    1987-01-01

    The crystal structure of W 18 O 49 , has been refined from an untwinned sample and registered by means of X-rays diffractometric techniques. The deformation of the polyhedra is described from the dispersion of the O-O distances, from the shape of the windows of the perovskite cages and from the location of the W inside their octahedra. A metallic cluster is observed, according to the weak value of the mean oxydation state of the W atoms. Calculations of sites potential are carried inside the large hexagonal tunnels which are empty. They suggest that the existence of a large cation as Cs + should be possible in the tunnels of such structures [fr

  16. ENZO: AN ADAPTIVE MESH REFINEMENT CODE FOR ASTROPHYSICS

    International Nuclear Information System (INIS)

    Bryan, Greg L.; Turk, Matthew J.; Norman, Michael L.; Bordner, James; Xu, Hao; Kritsuk, Alexei G.; O'Shea, Brian W.; Smith, Britton; Abel, Tom; Wang, Peng; Skillman, Samuel W.; Wise, John H.; Reynolds, Daniel R.; Collins, David C.; Harkness, Robert P.; Kim, Ji-hoon; Kuhlen, Michael; Goldbaum, Nathan; Hummels, Cameron; Tasker, Elizabeth

    2014-01-01

    This paper describes the open-source code Enzo, which uses block-structured adaptive mesh refinement to provide high spatial and temporal resolution for modeling astrophysical fluid flows. The code is Cartesian, can be run in one, two, and three dimensions, and supports a wide variety of physics including hydrodynamics, ideal and non-ideal magnetohydrodynamics, N-body dynamics (and, more broadly, self-gravity of fluids and particles), primordial gas chemistry, optically thin radiative cooling of primordial and metal-enriched plasmas (as well as some optically-thick cooling models), radiation transport, cosmological expansion, and models for star formation and feedback in a cosmological context. In addition to explaining the algorithms implemented, we present solutions for a wide range of test problems, demonstrate the code's parallel performance, and discuss the Enzo collaboration's code development methodology

  17. On Syntactic and Semantic Action Refinement

    NARCIS (Netherlands)

    Goltz, Ursula; Gorrieri, Roberto; Rensink, Arend

    1992-01-01

    The semantic definition of action refinement on labelled event structures is compared with the notion of syntactic substitution,which can be used as another notion of action refiment in a process algebraic setting. This is done by studying a process algebra equipped with the ACP sequential

  18. Individualism-Collectivism: Critique and Proposed Refinements.

    Science.gov (United States)

    Schwartz, Shalom H.

    1990-01-01

    Argues that the individualism-collectivism dichotomy overlooks values that inherently serve both individual and collective interests, ignores values that foster the goals of collectives other than the ingroup, and promotes the mistaken assumption that individualist and collectivist values form opposing syndromes. Suggests refined value types. (FMW)

  19. Evolution and Refinement with Endogenous Mistake Probabilities

    NARCIS (Netherlands)

    van Damme, E.E.C.; Weibull, J.

    1999-01-01

    Bergin and Lipman (1996) show that the refinement effect from the random mutations in the adaptive population dynamics in Kandori, Mailath and Rob (1993) and Young (1993) is due to restrictions on how these mutation rates vary across population states. We here model mutation rates as endogenously

  20. Quantum Geometry of Refined Topological Strings

    NARCIS (Netherlands)

    Aganagic, M.; Cheng, M.C.N.; Dijkgraaf, R.; Kreft, D.; Vafa, C.

    2012-01-01

    We consider branes in refined topological strings. We argue that their wavefunctions satisfy a Schrödinger equation depending on multiple times and prove this in the case where the topological string has a dual matrix model description. Furthermore, in the limit where one of the equivariant

  1. Oil refining expansion criteria for Brazil

    International Nuclear Information System (INIS)

    Tavares, M.E.E.; Szklo, A.S.; Machado, G.V.; Schaeffer, R.; Mariano, J.B.; Sala, J.F.

    2006-01-01

    This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks. (author)

  2. Oil refining expansion criteria for Brazil

    International Nuclear Information System (INIS)

    Tavares, Marina Elisabete Espinho; Szklo, Alexandre Salem; Machado, Giovani Vitoria; Schaeffer, Roberto; Mariano, Jacqueline Barboza; Sala, Janaina Francisco

    2006-01-01

    This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks

  3. Refinement from a control problem to program

    DEFF Research Database (Denmark)

    Schenke, Michael; Ravn, Anders P.

    1996-01-01

    The distinguishing feature of the presented refinement approach is that it links formalisms from a top level requirements notation down to programs together in a mathematically coherent development trajectory. The approach uses Duration Calculus, a real-time interval logic, to specifyrequirements...

  4. Refining the Eye: Dermatology and Visual Literacy

    Science.gov (United States)

    Zimmermann, Corinne; Huang, Jennifer T.; Buzney, Elizabeth A.

    2016-01-01

    In 2014 the Museum of Fine Arts Boston and Harvard Medical School began a partnership focused on building visual literacy skills for dermatology residents in the Harvard Combined Dermatology Residency Program. "Refining the Eye: Art and Dermatology", a four session workshop, took place in the museum's galleries and utilized the Visual…

  5. Refinement of the concept of uncertainty.

    Science.gov (United States)

    Penrod, J

    2001-04-01

    To analyse the conceptual maturity of uncertainty; to develop an expanded theoretical definition of uncertainty; to advance the concept using methods of concept refinement; and to analyse congruency with the conceptualization of uncertainty presented in the theory of hope, enduring, and suffering. Uncertainty is of concern in nursing as people experience complex life events surrounding health. In an earlier nursing study that linked the concepts of hope, enduring, and suffering into a single theoretical scheme, a state best described as 'uncertainty' arose. This study was undertaken to explore how this conceptualization fit with the scientific literature on uncertainty and to refine the concept. Initially, a concept analysis using advanced methods described by Morse, Hupcey, Mitcham and colleagues was completed. The concept was determined to be partially mature. A theoretical definition was derived and techniques of concept refinement using the literature as data were applied. The refined concept was found to be congruent with the concept of uncertainty that had emerged in the model of hope, enduring and suffering. Further investigation is needed to explore the extent of probabilistic reasoning and the effects of confidence and control on feelings of uncertainty and certainty.

  6. Red refinements of simplices into congruent subsimplices

    Czech Academy of Sciences Publication Activity Database

    Korotov, S.; Křížek, Michal

    2014-01-01

    Roč. 67, č. 12 (2014), s. 2199-2204 ISSN 0898-1221 R&D Projects: GA ČR GA14-02067S Institutional support: RVO:67985840 Keywords : sommerville tetrahedron * red refinement * higher-dimensional simplex Subject RIV: BA - General Mathematics Impact factor: 1.697, year: 2014 http://www.sciencedirect.com/science/article/pii/S0898122114000662

  7. Energy Bandwidth for Petroleum Refining Processes

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2006-10-01

    The petroleum refining energy bandwidth report analyzes the most energy-intensive unit operations used in U.S. refineries: crude oil distillation, fluid catalytic cracking, catalytic hydrotreating, catalytic reforming, and alkylation. The "bandwidth" provides a snapshot of the energy losses that can potentially be recovered through best practices and technology R&D.

  8. Robust Refinement as Implemented in TOPAS

    Energy Technology Data Exchange (ETDEWEB)

    Stone, K.; Stephens, P

    2010-01-01

    A robust refinement procedure is implemented in the program TOPAS through an iterative reweighting of the data. Examples are given of the procedure as applied to fitting partially overlapped peaks by full and partial models and also of the structures of ibuprofen and acetaminophen in the presence of unmodeled impurity contributions

  9. An Automated Policy Refinement Process Supported by Expert Knowledge

    OpenAIRE

    Rochaeli, Taufiq

    2009-01-01

    In a policy-based system management, a policy refinement process is required to translate abstract policies, which are specified by human, into enforceable policies, which are enforced by machine. However, a manual policy refinement process imposes some problems. The first problem is that it requires expert knowledge to perform the policy refinement process. The second problem is that refining policies for complex systems is a tedious task. Manual refinement process may cause some negative co...

  10. Determination of Cation Distributions in Mineral Structures by use of the Rietveld Full-Profile Refinement Technique

    International Nuclear Information System (INIS)

    Nord, A.G.

    1986-01-01

    Use of the Rietveld full-profile refinement technique with X-ray or neutron powder diffraction data for the determination of divalent-metal cation distributions in three mineral structure types (farringtonite, grafonite, sarcopside) is demonstrated. The accuracy of the conventional cation distribution coefficient Ksub(D) is about 5-10 percent with 24-46 parameters to be refined, and the averaged metal-oxygen distances are reliable and well correlated to the observed cation distribution pattern. In particular the usefulness of the Rietveld technique in combination with Moessbauer spectroscopy is stressed. Some concluding remarks are also given

  11. The relationship between viscosity and refinement efficiency of pure aluminum by Al-Ti-B refiner

    Energy Technology Data Exchange (ETDEWEB)

    Yu Lina [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, 73 Jingshi Road, Jinan 250061 (China); Liu Xiangfa [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, 73 Jingshi Road, Jinan 250061 (China)]. E-mail: xfliu@sdu.edu.cn

    2006-11-30

    The relationship between viscosity and refinement efficiency of pure aluminum with the addition of Al-Ti-B master alloy was studied in this paper. The experimental results show that when the grain size of solidified sample is finer the viscosity of the melt is higher after the addition of different Al-Ti-B master alloys. This indicates that viscosity can be used to approximately estimate the refinement efficiency of Al-Ti-B refiners in production to a certain extent. The main reason was also discussed in this paper by using transmission electron microscopy (TEM) analysis and differential scanning calorimetry (DSC) experiment.

  12. Effect of zirconium addition on welding of aluminum grain refined by titanium

    International Nuclear Information System (INIS)

    Zaid, A.I.O.

    2011-01-01

    Aluminum and its alloys solidify in large grains columnar structure which tends to reduce their mechanical behaviour and surface quality. Therefore, they are industrially grain refined by titanium or titanium + boron. Furthermore, aluminum oxidizes in ordinary atmosphere which makes its weldability difficult and weak. Therefore, it is anticipated that the effect of addition of zirconium at a weight percentages of 0.1% (which proved to be an effective grain refiner on the weldability of aluminum grain refined by Ti) is worthwhile investigating. This formed the objective of this research work. In this paper, the effect of zirconium addition at a weight percentage of 0.1%, which corresponds to the peritctic limit on the aluminum-zirconium phase diagram, on the weldability of aluminum grain refined by Ti is investigated. Rolled sheets of commercially pure aluminum, Al grain refined Ti of 3 mm thickness were welded together using Gas Tungsten Arc Welding method (GTAW), formerly known as TIG. A constant air gap was maintained at a constant current level, 30 ampere AC, was used because it removes the oxides of the welding process under the same process parameters. Metallographic examination of weldments of the different combinations of aluminum and its microalloys at the heat affected zone, HAZ, and base metal was carried out and examined for width, porosity, cracks and microhardness. It was found that grain refining of commercially pure aluminum by Ti resulted in enhancement of its weldability. Similarly, addition of zirconium to Al grain refined by Ti resulted in further enhancement of the weldment. Photomicrographs of the HAZ regions are presented and discussed. (author)

  13. Studies of the Action of Grain-Refining Particles in Aluminium Alloys

    Science.gov (United States)

    Schumacher, P.; Greer, A. L.

    Crystallization from a melt and from a metallic glass both occur in an undercooled liquid. In this way identical nucleation mechanisms can operate in the two cases. However, in metallic glasses, unlike conventional solidification at low undercooling, the low atomic mobility permits the resolution and microscopical study of nucleation processes on added particles. Conventional aluminium grain-refiner based on Al-Ti-B has been used to obtain nucleant particles embedded in a glassy matrix of Al85Y8Ni5Co2 (at%). During crystallization from the glassy state, nucleation and growth of α-Al can be observed on TiB2 particles coated with a layer of Al3Ti Empirical relations found in casting practice of Al-alloys, such as excess Ti necessary for grain refinement, can be related to the observed nucleation mechanism, which is found to be very sensitive to both crystallographic and chemical factors.

  14. Grain refinement of permanent mold cast copper base alloys. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M.

    2004-04-29

    . Aluminum promoted b phase formation and modified the grain structure from dendritic to equiaxed. Lead or bismuth reduces the size of grains, but not change the morphology of the structure in Cu-Zn alloys. The grain size of the Cu-Zn-alloy can be reduced from 3000 mm to 300 mm after the addition of aluminum and lead. Similar effects were observed in EnviroBrass III after the addition of aluminum and bismuth. Boron refined the structure of yellow brasses in the presence of iron. At least 50 ppm of iron and 3 ppm of boron are necessary to cause grain refinement in these alloys. Precipitation of iron from the melt is identified as the cause of grain refinement. Boron initiates the precipitation of iron which could not be explained at this time. On the other hand zirconium causes some reduction in grain size in all four alloys investigated. The critical limit for the zirconium was found to be around 100 ppm below which not much refinement could be observed. The mechanism of grain refinement in the presence of zirconium could not be explained. Grain refinement by boron and iron can remain over a long period of time, at least for 72 hours of holding or after remelting few times. It is necessary to have the iron and boron contents above the critical limits mentioned earlier. On the other hand, refinement by zirconium is lost quite rapidly, some times within one hour of holding, mostly due to the loss of zirconium, most probably by oxidation, from the melt. In all the cases it is possible to revive the refinement by adding more of the appropriate refining element. Cooling curve analysis (thermal analysis) can be used successfully to predict the grain refinement in yellow brasses. The precipitation of iron in the liquid metal causes the metal to solidify without undercooling. Absence of this reaction, as indicated by the time-temperature (t-T) and its first derivative (dt/dT) curves, proved to be an indicator of refinement. The viability of the technique as an on-line quality

  15. Multivariate refined composite multiscale entropy analysis

    Energy Technology Data Exchange (ETDEWEB)

    Humeau-Heurtier, Anne, E-mail: anne.humeau@univ-angers.fr

    2016-04-01

    Multiscale entropy (MSE) has become a prevailing method to quantify signals complexity. MSE relies on sample entropy. However, MSE may yield imprecise complexity estimation at large scales, because sample entropy does not give precise estimation of entropy when short signals are processed. A refined composite multiscale entropy (RCMSE) has therefore recently been proposed. Nevertheless, RCMSE is for univariate signals only. The simultaneous analysis of multi-channel (multivariate) data often over-performs studies based on univariate signals. We therefore introduce an extension of RCMSE to multivariate data. Applications of multivariate RCMSE to simulated processes reveal its better performances over the standard multivariate MSE. - Highlights: • Multiscale entropy quantifies data complexity but may be inaccurate at large scale. • A refined composite multiscale entropy (RCMSE) has therefore recently been proposed. • Nevertheless, RCMSE is adapted to univariate time series only. • We herein introduce an extension of RCMSE to multivariate data. • It shows better performances than the standard multivariate multiscale entropy.

  16. Using supercritical fluids to refine hydrocarbons

    Science.gov (United States)

    Yarbro, Stephen Lee

    2014-11-25

    This is a method to reactively refine hydrocarbons, such as heavy oils with API gravities of less than 20.degree. and bitumen-like hydrocarbons with viscosities greater than 1000 cp at standard temperature and pressure using a selected fluid at supercritical conditions. The reaction portion of the method delivers lighter weight, more volatile hydrocarbons to an attached contacting device that operates in mixed subcritical or supercritical modes. This separates the reaction products into portions that are viable for use or sale without further conventional refining and hydro-processing techniques. This method produces valuable products with fewer processing steps, lower costs, increased worker safety due to less processing and handling, allow greater opportunity for new oil field development and subsequent positive economic impact, reduce related carbon dioxide, and wastes typical with conventional refineries.

  17. Refined 3d-3d correspondence

    Science.gov (United States)

    Alday, Luis F.; Genolini, Pietro Benetti; Bullimore, Mathew; van Loon, Mark

    2017-04-01

    We explore aspects of the correspondence between Seifert 3-manifolds and 3d N = 2 supersymmetric theories with a distinguished abelian flavour symmetry. We give a prescription for computing the squashed three-sphere partition functions of such 3d N = 2 theories constructed from boundary conditions and interfaces in a 4d N = 2∗ theory, mirroring the construction of Seifert manifold invariants via Dehn surgery. This is extended to include links in the Seifert manifold by the insertion of supersymmetric Wilson-'t Hooft loops in the 4d N = 2∗ theory. In the presence of a mass parameter cfor the distinguished flavour symmetry, we recover aspects of refined Chern-Simons theory with complex gauge group, and in particular construct an analytic continuation of the S-matrix of refined Chern-Simons theory.

  18. Structure and Activity Research of Hydrocarbons Refining Catalysts Based on Wastes of Ferroalloy Production

    OpenAIRE

    Zhanat Shomanova; Ruslan Safarov; Yuri Nosenko; Zheneta Tashmuchambetova; Alima Zharmagambetova

    2016-01-01

    An effective way of utilization of ferroalloy production wastes is preparing hydrocarbon refining catalysts from them. It is possible due to accordable transition metals containing in the wastes. In the work, we are presenting the results on elemental analysis of sludge samples from Aksu ferroalloy plant (Aksu, Kazakhstan), method of catalysts preparing, results of physical-chemical analysis of obtained catalysts (X-ray analysis, electron microscopy, the BET method etc.), results of using the...

  19. Solidification Based Grain Refinement in Steels

    Science.gov (United States)

    2009-07-24

    and a coarser microstructure forms (See Figure 17). ROLE OF COBALT ALUMINATE CoAI204 produced very different results in the 1010 and 1030 TA...determine what role CoAl204 played in both steels. Other researchers have observed refinement with cobalt aluminate.2"󈧙 Their work has been using...C0AI2O4 as an interior paint for superalloy investment castings. The alloys examined solidified primarily as austenite. These findings are in agreement

  20. Refining molecular potentials using atom interferometry

    International Nuclear Information System (INIS)

    Forrey, R.C.; Kharchenko, V.; Dalgarno, A.; You, L.

    1997-01-01

    We present a theoretical study of the index of refraction of argon for the propagation of sodium matter waves. The sensitivity of the index of refraction to the details of the molecular potential curve is analyzed. Our calculations reveal velocity-dependent oscillations in the index of refraction that may be detectable, particularly at low temperatures, in atom interferometry measurements. A procedure for refining molecular potential curves is outlined. copyright 1997 The American Physical Society

  1. Problems persist for French refining sector

    International Nuclear Information System (INIS)

    Beck, R.J.

    1992-01-01

    This paper reports that France's refiners face a continuing shortfall of middle distillate capacity and a persistent surplus of heavy fuel oil. That's the main conclusion of the official Hydrocarbon Directorate's report on how France's refining sector performed in 1991. Imports up---The directorate noted that although net production of refined products in French refineries rose to 1.534 million b/d in 1991 from 1.48 million b/d in 1990, products imports jumped 9.7% to 602,000 b/d in the period. The glut of heavy fuel oil eased to some extent last year because French nuclear power capacity, heavily dependent on ample water supplies, was crimped by drought. That spawned fuel switching. The most note worthy increase in imports was for motor diesel, climbing to 176,000 b/d from 148,000 b/d in 1990. Tax credits are spurring French consumption of that fuel. For the first time, consumption of motor diesel in 1991 outstripped that of gasoline at 374,000 b/d and 356,000 b/d respectively

  2. Humanoid Mobile Manipulation Using Controller Refinement

    Science.gov (United States)

    Platt, Robert; Burridge, Robert; Diftler, Myron; Graf, Jodi; Goza, Mike; Huber, Eric; Brock, Oliver

    2006-01-01

    An important class of mobile manipulation problems are move-to-grasp problems where a mobile robot must navigate to and pick up an object. One of the distinguishing features of this class of tasks is its coarse-to-fine structure. Near the beginning of the task, the robot can only sense the target object coarsely or indirectly and make gross motion toward the object. However, after the robot has located and approached the object, the robot must finely control its grasping contacts using precise visual and haptic feedback. This paper proposes that move-to-grasp problems are naturally solved by a sequence of controllers that iteratively refines what ultimately becomes the final solution. This paper introduces the notion of a refining sequence of controllers and characterizes this type of solution. The approach is demonstrated in a move-to-grasp task where Robonaut, the NASA/JSC dexterous humanoid, is mounted on a mobile base and navigates to and picks up a geological sample box. In a series of tests, it is shown that a refining sequence of controllers decreases variance in robot configuration relative to the sample box until a successful grasp has been achieved.

  3. Formal refinement of extended state machines

    Directory of Open Access Journals (Sweden)

    Thomas Fayolle

    2016-06-01

    Full Text Available In a traditional formal development process, e.g. using the B method, the informal user requirements are (manually translated into a global abstract formal specification. This translation is especially difficult to achieve. The Event-B method was developed to incrementally and formally construct such a specification using stepwise refinement. Each increment takes into account new properties and system aspects. In this paper, we propose to couple a graphical notation called Algebraic State-Transition Diagrams (ASTD with an Event-B specification in order to provide a better understanding of the software behaviour. The dynamic behaviour is captured by the ASTD, which is based on automata and process algebra operators, while the data model is described by means of an Event-B specification. We propose a methodology to incrementally refine such specification couplings, taking into account new refinement relations and consistency conditions between the control specification and the data specification. We compare the specifications obtained using each approach for readability and proof complexity. The advantages and drawbacks of the traditional approach and of our methodology are discussed. The whole process is illustrated by a railway CBTC-like case study. Our approach is supported by tools for translating ASTD's into B and Event-B into B.

  4. A New Induction Heating Floating-Zone Refining Furnace for Ultrapurification of Iron-Chromium Alloys

    OpenAIRE

    Takaki, S.; Ashino, Y.; Morimoto, Y.; Tanino, M.; Abiko, K.

    1995-01-01

    A new induction heating floating-zone refining (IHFZR) furnace was designed and constructed using ultrahigh vacuum technology for the ultrapurification of base metals. The ultrahigh vacuum attainable in this furnace is so good as 1x10-7} Pa that a base metal bar can be zone-melted in both ultrahigh vacuum and higher-purity gas atmosphere containing less residual gases. The outline of this IHFZR furnace and the results of its application to the purification of high-purity iron, Fe-18%Cr alloy ...

  5. Grain Refinement of Permanent Mold Cast Copper Base Alloys

    Energy Technology Data Exchange (ETDEWEB)

    M.Sadayappan; J.P.Thomson; M.Elboujdaini; G.Ping Gu; M. Sahoo

    2005-04-01

    Grain refinement is a well established process for many cast and wrought alloys. The mechanical properties of various alloys could be enhanced by reducing the grain size. Refinement is also known to improve casting characteristics such as fluidity and hot tearing. Grain refinement of copper-base alloys is not widely used, especially in sand casting process. However, in permanent mold casting of copper alloys it is now common to use grain refinement to counteract the problem of severe hot tearing which also improves the pressure tightness of plumbing components. The mechanism of grain refinement in copper-base alloys is not well understood. The issues to be studied include the effect of minor alloy additions on the microstructure, their interaction with the grain refiner, effect of cooling rate, and loss of grain refinement (fading). In this investigation, efforts were made to explore and understand grain refinement of copper alloys, especially in permanent mold casting conditions.

  6. Generalizing Refinement Operators to Learn Prenex Conjunctive Normal Forms

    NARCIS (Netherlands)

    S-H. Nienhuys-Cheng (Shan-Hwei); W. van Laer; J. Ramon; L. de Raedt

    2000-01-01

    textabstractInductive Logic Programming considers almost exclusively universally quantied theories. To add expressiveness, prenex conjunctive normal forms (PCNF) with existential variables should also be considered. ILP mostly uses learning with refinement operators. To extend refinement operators

  7. A New Strategy to Refine Crude Indian Sardine Oil.

    Science.gov (United States)

    Charanyaa, S; Belur, Prasanna D; Regupathi, I

    2017-05-01

    Current work aims to develop a refining process for removing phospholipids, free fatty acids (FFA), and metal ions without affecting n-3 polyunsaturated fatty acid (n-3 PUFA) esters present in the crude Indian sardine oil. Sardine oil was subjected to degumming with various acids (orthophosphoric acid, acetic acid, and lactic acid), conventional and membrane assisted deacidification using various solvents (methanol, ethanol, propanol and butanol) and bleaching with bleaching agents (GAC, activated earth and bentonite) and all the process parameters were further optimized. Degumming with 5%(w/w) ortho phosphoric acid, two stage solvent extraction with methanol at 1:1 (w/w) in each stage and bleaching with 3% (w/w) activated charcoal loading, at 80ºC for 10 minutes resulted in the reduction of phospholipid content to 5.66 ppm from 612.66 ppm, FFA to 0.56% from 5.64% with the complete removal of iron and mercury. Under these conditions, the obtained bleached oil showed an enhancement of n-3 PUFA from 16.39 % (11.19 Eicosapentaenoic acid (EPA) + 5.20 Docosahexaenoic acid (DHA)) to 17.91 % (11.81 EPA + 6.1 DHA). Replacing conventional solvent extraction with membrane deacidification using microporous, hydrophobic polytetrafluoroethylene membrane (PTFE), resulted in a lesser solvent residue (0.25% (w/w)) in the deacidified oil. In view of lack of reports on refining of n-3 PUFA rich marine oils without concomitant loss of n-3 PUFA, this report is significant.

  8. Effects and mechanisms of grain refinement in aluminium alloys

    Indian Academy of Sciences (India)

    Unknown

    grain refine the solidified product. The mechanism of grain refinement is of considerable ... The present paper attempts to review the literature on the nucleant effects and solute effects on grain refinement and ... cast alloys. Firstly, reduced mechanical properties have been noted in plate products for structural application.

  9. Grain refinement of AZ31 magnesium alloy by electromagnetic ...

    Indian Academy of Sciences (India)

    The effects of electromagnetic stirring and Al4C3 grain refiner on the grain refinement of semicontinuously cast AZ31 magnesium alloy were discussed in this investigation. The results indicate that electromagnetic stirring has an effective refining effect on the grain size of AZ31 magnesium alloy under the effect of Al4C3 ...

  10. Effects and mechanisms of grain refinement in aluminium alloys

    Indian Academy of Sciences (India)

    Unknown

    Abstract. Grain refinement plays a crucial role in improving characteristics and properties of cast and wrought aluminium alloys. Generally Al–Ti and Al–Ti–B master alloys are added to the aluminium alloys to grain refine the solidified product. The mechanism of grain refinement is of considerable controversy in the scientific ...

  11. Grain refinement of AZ31 magnesium alloy by electromagnetic ...

    Indian Academy of Sciences (India)

    Abstract. The effects of electromagnetic stirring and Al4C3 grain refiner on the grain refinement of semi- continuously cast AZ31 magnesium alloy were discussed in this investigation. The results indicate that electromag- netic stirring has an effective refining effect on the grain size of AZ31 magnesium alloy under the effect of ...

  12. Principles of minimum cost refining for optimum linerboard strength

    Science.gov (United States)

    Thomas J. Urbanik; Jong Myoung Won

    2006-01-01

    The mechanical properties of paper at a single basis weight and a single targeted refining freeness level have traditionally been used to compare papers. Understanding the economics of corrugated fiberboard requires a more global characterization of the variation of mechanical properties and refining energy consumption with freeness. The cost of refining energy to...

  13. Effects and mechanisms of grain refinement in aluminium alloys

    Indian Academy of Sciences (India)

    2016-08-26

    Aug 26, 2016 ... Grain refinement plays a crucial role in improving characteristics and properties of cast and wrought aluminium alloys. Generally Al–Ti and Al–Ti–B master alloys are added to the aluminium alloys to grain refine the solidified product. The mechanism of grain refinement is of considerable controversy in the ...

  14. Refining Grasp Affordance Models by Experience

    DEFF Research Database (Denmark)

    Detry, Renaud; Kraft, Dirk; Buch, Anders Glent

    2010-01-01

    grasps. These affordances are represented probabilistically with grasp densities, which correspond to continuous density functions defined on the space of 6D gripper poses. A grasp density characterizes an object’s grasp affordance; densities are linked to visual stimuli through registration...... with a visual model of the object they characterize. We explore a batch-oriented, experience-based learning paradigm where grasps sampled randomly from a density are performed, and an importance-sampling algorithm learns a refined density from the outcomes of these experiences. The first such learning cycle...

  15. Local adaptive mesh refinement for shock hydrodynamics

    International Nuclear Information System (INIS)

    Berger, M.J.; Colella, P.; Lawrence Livermore Laboratory, Livermore, 94550 California)

    1989-01-01

    The aim of this work is the development of an automatic, adaptive mesh refinement strategy for solving hyperbolic conservation laws in two dimensions. There are two main difficulties in doing this. The first problem is due to the presence of discontinuities in the solution and the effect on them of discontinuities in the mesh. The second problem is how to organize the algorithm to minimize memory and CPU overhead. This is an important consideration and will continue to be important as more sophisticated algorithms that use data structures other than arrays are developed for use on vector and parallel computers. copyright 1989 Academic Press, Inc

  16. Formal language theory: refining the Chomsky hierarchy.

    Science.gov (United States)

    Jäger, Gerhard; Rogers, James

    2012-07-19

    The first part of this article gives a brief overview of the four levels of the Chomsky hierarchy, with a special emphasis on context-free and regular languages. It then recapitulates the arguments why neither regular nor context-free grammar is sufficiently expressive to capture all phenomena in the natural language syntax. In the second part, two refinements of the Chomsky hierarchy are reviewed, which are both relevant to the extant research in cognitive science: the mildly context-sensitive languages (which are located between context-free and context-sensitive languages), and the sub-regular hierarchy (which distinguishes several levels of complexity within the class of regular languages).

  17. Effects of grain refinement on the biocorrosion and in vitro bioactivity of magnesium

    Energy Technology Data Exchange (ETDEWEB)

    Saha, Partha; Roy, Mangal [Department of Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Datta, Moni Kanchan [Department of Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Center for Complex Engineered Multifunctional Materials, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Lee, Boeun [Department of Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Kumta, Prashant N., E-mail: pkumta@pitt.edu [Department of Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Center for Complex Engineered Multifunctional Materials, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Mechanical Engineering and Materials Science, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Chemical and Petroleum Engineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); School of Dental Medicine, University of Pittsburgh, PA 15261 (United States); McGowan Institute of Regenerative Medicine, University of Pittsburgh, PA 15261 (United States)

    2015-12-01

    Magnesium is a new class of biodegradable metals potentially suitable for bone fracture fixation due to its suitable mechanical properties, high degradability and biocompatibility. However, rapid corrosion and loss in mechanical strength under physiological conditions render it unsuitable for load-bearing applications. In the present study, grain refinement was implemented to control bio-corrosion demonstrating improved in vitro bioactivity of magnesium. Pure commercial magnesium was grain refined using different amounts of zirconium (0.25 and 1.0 wt.%). Corrosion behavior was studied by potentiodynamic polarization (PDP) and mass loss immersion tests demonstrating corrosion rate decrease with grain size reduction. In vitro biocompatibility tests conducted by MC3T3-E1 pre-osteoblast cells and measured by DNA quantification demonstrate significant increase in cell proliferation for Mg–1 wt.% Zr at day 5. Similarly, alkaline phosphatase (ALP) activity was higher for grain refined Mg. Alloys were also tested for ability to support osteoclast differentiation using RAW264.7 monocytes with receptor activator of nuclear factor kappa-β ligand (RANKL) supplemented cell culture. Osteoclast differentiation process was observed to be severely restricted for smaller grained Mg. Overall, the results indicate grain refinement to be useful not only for improving corrosion resistance of Mg implants for bone fixation devices but also potentially modulate bone regeneration around the implant. - Highlights: • The biocorrosion and biocompatibility of pure Mg and Mg grain refined with different Zr levels were investigated. • Corrosion resistance in HBSS and compressive strength of pure Mg was significantly improved with Zr addition. • Electrochemical and immersion corrosion tests showed a fourfold decrease in corrosion rate of pure Mg with 1% Zr addition. • Grain refinement of pure Mg demonstrated enhanced osteoblast cell activity and proliferation.

  18. Distribution feeder reconfiguration with refined genetic algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Lin, W.-M.; Cheng, F.-S. [National Sun Yat-Sen University, Kaohsiung (China). Dept. of Electrical Engineering; Tsay, M.-T. [Cheng-Shiu Institute of Technology, Kaohsiung (China). Dept. of Electrical Engineering

    2000-11-01

    A refined genetic algorithm for a distribution feeder reconfiguration to reduce losses is presented. The problem is optimised in a stochastic searching manner similar to that of the conventional GA. The initial population is determined by opening the switches with the lowest current in every mesh derived in the optimal power flow (OPF), with all switches closed. Solutions provided by OPF are generally the optimum or near-optimal solutions for most cases, so prematurity could occur. To avoid prematurity, the conventional crossover and mutation scheme was refined by a competition mechanism. So the dilemma of choosing a proper probability for crossover and mutation can be avoided. The two processes were also combined into one to save computation time. Tabu lists with heuristic rules were also employed in the searching process to enhance performance. The new approach provides an overall switching decision instead of a successive pattern, which tends to converge to a local optimum. Many tests were conducted and the results have shown that RGA has advantages over many other previously developed algorithms. (author)

  19. Refining Automatically Extracted Knowledge Bases Using Crowdsourcing.

    Science.gov (United States)

    Li, Chunhua; Zhao, Pengpeng; Sheng, Victor S; Xian, Xuefeng; Wu, Jian; Cui, Zhiming

    2017-01-01

    Machine-constructed knowledge bases often contain noisy and inaccurate facts. There exists significant work in developing automated algorithms for knowledge base refinement. Automated approaches improve the quality of knowledge bases but are far from perfect. In this paper, we leverage crowdsourcing to improve the quality of automatically extracted knowledge bases. As human labelling is costly, an important research challenge is how we can use limited human resources to maximize the quality improvement for a knowledge base. To address this problem, we first introduce a concept of semantic constraints that can be used to detect potential errors and do inference among candidate facts. Then, based on semantic constraints, we propose rank-based and graph-based algorithms for crowdsourced knowledge refining, which judiciously select the most beneficial candidate facts to conduct crowdsourcing and prune unnecessary questions. Our experiments show that our method improves the quality of knowledge bases significantly and outperforms state-of-the-art automatic methods under a reasonable crowdsourcing cost.

  20. Pacific Basin Heavy Oil Refining Capacity

    Directory of Open Access Journals (Sweden)

    David Hackett

    2013-02-01

    Full Text Available The United States today is Canada’s largest customer for oil and refined oil products. However, this relationship may be strained due to physical, economic and political influences. Pipeline capacity is approaching its limits; Canadian oil is selling at substantive discounts to world market prices; and U.S. demand for crude oil and finished products (such as gasoline, has begun to flatten significantly relative to historical rates. Lower demand, combined with increased shale oil production, means U.S. demand for Canadian oil is expected to continue to decline. Under these circumstances, gaining access to new markets such as those in the Asia-Pacific region is becoming more and more important for the Canadian economy. However, expanding pipeline capacity to the Pacific via the proposed Northern Gateway pipeline and the planned Trans Mountain pipeline expansion is only feasible when there is sufficient demand and processing capacity to support Canadian crude blends. Canadian heavy oil requires more refining and produces less valuable end products than other lighter and sweeter blends. Canadian producers must compete with lighter, sweeter oils from the Middle East, and elsewhere, for a place in the Pacific Basin refineries built to handle heavy crude blends. Canadian oil sands producers are currently expanding production capacity. Once complete, the Northern Gateway pipeline and the Trans Mountain expansion are expected to deliver an additional 500,000 to 1.1 million barrels a day to tankers on the Pacific coast. Through this survey of the capacity of Pacific Basin refineries, including existing and proposed facilities, we have concluded that there is sufficient technical capacity in the Pacific Basin to refine the additional Canadian volume; however, there may be some modifications required to certain refineries to allow them to process Western Canadian crude. Any additional capacity for Canadian oil would require refinery modifications or

  1. Increased delignification by white rot fungi after pressure refining Miscanthus.

    Science.gov (United States)

    Baker, Paul W; Charlton, Adam; Hale, Mike D C

    2015-01-01

    Pressure refining, a pulp making process to separate fibres of lignocellulosic materials, deposits lignin granules on the surface of the fibres that could enable increased access to lignin degrading enzymes. Three different white rot fungi were grown on pressure refined (at 6 bar and 8 bar) and milled Miscanthus. Growth after 28 days showed highest biomass losses on milled Miscanthus compared to pressure refined Miscanthus. Ceriporiopsis subvermispora caused a significantly higher proportion of lignin removal when grown on 6 bar pressure refined Miscanthus compared to growth on 8 bar pressure refined Miscanthus and milled Miscanthus. RM22b followed a similar trend but Phlebiopsis gigantea SPLog6 did not. Conversely, C. subvermispora growing on pressure refined Miscanthus revealed that the proportion of cellulose increased. These results show that two of the three white rot fungi used in this study showed higher delignification on pressure refined Miscanthus than milled Miscanthus. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. Epidemiological Approaches to Metal Toxicology

    DEFF Research Database (Denmark)

    Grandjean, Philippe; Budtz-Jørgensen, Esben

    2014-01-01

    Epidemiological methods are crucial to extract as much valid information as possible from human metal exposures. Thus, modern epidemiological approaches have elucidated human health effects that were not apparent in the past. At the same time, metal toxicology has served as a useful arena...... for testing and further refining methods for study design and data analysis. In contrast to most organic compounds, metals are not broken down, and many of them are retained in the body for long periods, thereby facilitating exposure assessment. In conjunction with the use of inexpensive metal analytical...... to their propensity to cause chronic or delayed toxicity, epidemiological studies of metal toxicity have focused on a wide variety of organ systems, subtle effects as well as mortality, and differences in susceptibility. Toxic metals often serve as paradigms of environmental and occupational toxicity...

  3. Electrical conductivity and microstructure by Rietveld refinement of doped Cu-Ni powder alloys

    Energy Technology Data Exchange (ETDEWEB)

    Fambrini, A.S.; Monteiro, W.A.; Orrego, R.M.M.; Marques, I.M.; Carrio, Juan A.G., E-mail: jgcarrio@mackenzie.br, E-mail: iara_m_@hotmail.com [Universidade Presbiteriana Mackenzie (UPM/CCH), Sao Paulo, SP (Brazil). Centro de Ciencias e Humanidades. Dept. de Fisica

    2009-07-01

    This work presents a comparative study of microstructural and electrical properties of polycrystalline material from two different Cu-Ni alloys: Cu-Ni-Pt and Cu-Ni-Al. The first one of them was produced in electric furnace with voltaic arc and the other was produced by powder metallurgy. The microstructure of the samples was studied by optical microscopy, Vickers micro hardness and x rays powder diffraction. Their electrical conductivity was measured with a milliohmmeter Agilent (HP) 4338B. Refinements of the crystalline structure of the samples were performed by the Rietveld method, using the refinement program GSAS. The refinement results and Fourier differences calculations indicate that the copper matrix structure presents not significant distortions by the used amounts of the other metal atoms. In both cases a sequence of thermo mechanical treatments was developed with the intention of increasing the hardness maintaining the electrical conductivity of the alloys. The refinements also allowed a study of the dependence of the micro-structure and the thermo mechanical treatments of the samples. (author)

  4. Application of Modified Cores for Grain Refinement in Castings of Aircraft Turbine Blades

    Directory of Open Access Journals (Sweden)

    Binczyk F.

    2017-09-01

    Full Text Available Paper presents the results of research on modified surface grain refinement method used in investment casting of hollow, thin-walled parts made of nickel based superalloys. In the current technology, the refining inoculant is applied to the surface of the wax pattern and then, it is transferred to the ceramic mould surface during dewaxing. Because of its chemical activity the inoculant may react with the liquid metal which can cause defects on the external surface of the cast part. The method proposed in the paper aims to reduce the risk of external surface defects by applying the grain refiner only to the ceramic core which shapes the internal surface of the hollow casting. In case of thin-walled parts the grain refinement effect is visible throughout the thickness of the walls. The method is meant to be used when internal surface finish is less important, like for example, aircraft engine turbine blades, where the hollowing of the cast is mainly used to lower the weight and aid in cooling during operation.

  5. Effect of strontium on the grain refining efficiency of Mg-3Al alloy refined by carbon inoculation

    International Nuclear Information System (INIS)

    Du Jun; Yang Jian; Kuwabara, Mamoru; Li Wenfang; Peng Jihua

    2009-01-01

    The effect of Sr on the grain refining efficiency of the Mg-3Al alloy refined by carbon inoculation has been investigated in the present study. A significant grain refinement was obtained for the Mg-3Al alloy treated with either 0.2% C or 0.2% Sr. The Al-C-O particles were found in the sample refined by 0.2% C, and the element O should come from reaction between Al 4 C 3 nuclei of Mg grains and water during the process of sample preparation. The grain size of the sample refined by carbon inoculation was further decreased after the combined addition of Sr. The grain size decreased with increasing Sr content. Much higher refining efficiency was obtained when the Sr addition was increased to 0.5%. Sr is an effective element to improve the grain refining efficiency for the Mg-Al alloys refined by carbon inoculation. The number of Al 4 C 3 particles in the sample refined by the combination of carbon and Sr was more than that in the sample refined by only carbon. No Al-C-O-Sr-rich particles were obviously found in the sample refined by the combination of carbon and a little (<0.5%) Sr addition

  6. Visualization Tools for Adaptive Mesh Refinement Data

    Energy Technology Data Exchange (ETDEWEB)

    Weber, Gunther H.; Beckner, Vincent E.; Childs, Hank; Ligocki,Terry J.; Miller, Mark C.; Van Straalen, Brian; Bethel, E. Wes

    2007-05-09

    Adaptive Mesh Refinement (AMR) is a highly effective method for simulations that span a large range of spatiotemporal scales, such as astrophysical simulations that must accommodate ranges from interstellar to sub-planetary. Most mainstream visualization tools still lack support for AMR as a first class data type and AMR code teams use custom built applications for AMR visualization. The Department of Energy's (DOE's) Science Discovery through Advanced Computing (SciDAC) Visualization and Analytics Center for Enabling Technologies (VACET) is currently working on extending VisIt, which is an open source visualization tool that accommodates AMR as a first-class data type. These efforts will bridge the gap between general-purpose visualization applications and highly specialized AMR visual analysis applications. Here, we give an overview of the state of the art in AMR visualization research and tools and describe how VisIt currently handles AMR data.

  7. Formal language theory: refining the Chomsky hierarchy

    Science.gov (United States)

    Jäger, Gerhard; Rogers, James

    2012-01-01

    The first part of this article gives a brief overview of the four levels of the Chomsky hierarchy, with a special emphasis on context-free and regular languages. It then recapitulates the arguments why neither regular nor context-free grammar is sufficiently expressive to capture all phenomena in the natural language syntax. In the second part, two refinements of the Chomsky hierarchy are reviewed, which are both relevant to the extant research in cognitive science: the mildly context-sensitive languages (which are located between context-free and context-sensitive languages), and the sub-regular hierarchy (which distinguishes several levels of complexity within the class of regular languages). PMID:22688632

  8. Panorama 2011: Refining: varying conditions by region

    International Nuclear Information System (INIS)

    Silva, C.

    2011-01-01

    The economic crisis has further weakened a sector that was already facing difficulties, if we look beyond the flush period (2005-2008) when, buoyed by strong demand, margins remained high and refiners could generate profits while maintaining a healthy level of activity. Falling demand and increased over-capacity in some regions - the immediate consequences of the deteriorating economic conditions over the past two years - have led to declining margins and to financial accounts being in the red. The adoption of increasingly stringent emissions standards and product specifications, burdensome regulatory requirements for refineries (for combating local pollution and reducing greenhouse gas emissions), stiffer competition from new fuels: all of these structural factors are weakening the sector, especially in industrialized nations with their more rigorous regulatory compliance. In this generally gloomy climate, numerous new projects are still being envisaged - although many have recently been postponed and tend to be concentrated in developing countries. (author)

  9. Refining prices and margins in 1998

    International Nuclear Information System (INIS)

    Favennec, J.P.; Baudoin, C.

    1999-01-01

    Despite a business environment that was globally mediocre due primarily to the Asian crisis and to a mild winter in the northern hemisphere, the signs of improvement noted in the refining activity in 1996 were borne out in 1997. But the situation is not yet satisfactory in this sector: the low return on invested capital and the financing of environmental protection expenditure are giving cause for concern. In 1998, the drop in crude oil prices and the concomitant fall in petroleum product prices was ultimately rather favorable to margins. Two elements tended to put a damper on this relative optimism. First of all, margins continue to be extremely volatile and, secondly, the worsening of the economic and financial crisis observed during the summer made for a sharp decline in margins in all geographic regions, especially Asia

  10. China's oil market and refining sector

    International Nuclear Information System (INIS)

    Yamaguchi, N.D.; Fridley, D.G.

    2000-01-01

    The article assesses the future for China's oil industry as the country makes the transition from a command economy to an international market. China has one of the world's biggest oil industries and recent years have seen much growth in exploration and development, refining capacity and trade. China is more and more dependent on oil imports and is now a major international player; it has attracted much outside investment. Diagrams show (i) how coal dominates other sources of energy in China; (ii) crude production 1977-1998; (iii) how Middle East crudes now dominate Chinese crude imports; (iv) the growth of petroleum demand in China; (v) the Chinese demand for petroleum products; (vi) the growth in transport fuels; (vii) Chinese product imports: import ban targeted diesel; (viii) crude imports favoured over product imports and (ix) refinery capacity and throughput. The changes are expected to result in further integration into international markets, increased transparency and a healthier oil business

  11. Japan's oil market and refining sector

    International Nuclear Information System (INIS)

    Yamaguchi, N.D.

    2002-01-01

    The present economic situation in Japan is discussed. In particular, the focus is on fluctuations in oil product demand, imports of crude oil, and the refining industry. Throughout the 1990s, Japan was plagued by a volatile economy and the new millennium has shown no improvement. A prolonged recession means that the country now has little confidence in its leaders and its institutions, consumer confidence is low and asset values have deflated. Due to a low birth rate and long life expectancy, the population is aging and this means lower savings rates. The contrast between the present situation and the so-called economic miracle once enjoyed by the Japanese is hard to accept, but despite all this, the Japanese lifestyle and economy are to be envied

  12. Refining of metallurgical silicon by directional solidification

    Energy Technology Data Exchange (ETDEWEB)

    Martorano, M.A., E-mail: martoran@usp.br [Department of Metallurgical and Materials Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2463 Sao Paulo-SP, 05508-900 (Brazil); Neto, J.B. Ferreira, E-mail: jbfn@ipt.br [Laboratory of Metallurgy and Ceramics Materials, Institute for Technological Research, Av. Prof. Almeida Prado, 532, Sao Paulo-SP, 05508-901 (Brazil); Oliveira, T.S., E-mail: theo.usp@bol.com.br [Department of Metallurgical and Materials Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2463 Sao Paulo-SP, 05508-900 (Brazil); Tsubaki, T.O., E-mail: tomoe@ipt.br [Laboratory of Metallurgy and Ceramics Materials, Institute for Technological Research, Av. Prof. Almeida Prado, 532, Sao Paulo-SP, 05508-901 (Brazil)

    2011-02-25

    The directional solidification of a typical and a previously refined metallurgical silicon was carried out in a vertical Bridgman furnace. The mold velocity out of the hot zone of the furnace changed from one experiment to another in the range between 5 and 110 {mu}m s{sup -1}. Samples were extracted from the cylindrical ingots obtained in the experiments to investigate the effects of the mold velocity on the micro and macrostructures and on the concentration profiles of impurities along the ingots. At the lowest mold velocity, the macrostructures consist of columnar grains oriented approximately parallel to the ingot axis. As velocity increases, grains become thinner and more inclined in the radial direction. Precipitated particles containing Si, Fe, Al, and Ti are observed at the top of all ingots and, as the mold velocity increases, they are also seen at the ingot bottom and middle. The concentration profiles of several impurities have been measured along the ingots by inductively coupled plasma atomic emission spectrometry (ICP), indicating an accumulation of impurities at the ingot top. Consequently, the bottom and middle of the ingots are purer than the corresponding metallurgical silicon from which they solidified. Slices from the ingot bottom have also been analyzed by the glow discharge mass spectrometry technique (GDMS), allowing measurement of impurity concentrations that were below the quantification limit of the ICP. The purification effect and the accumulation of impurities at the ingot top are more pronounced as the mold velocity decreases. In the ingots obtained from the typical metallurgical silicon at the lowest mold velocities (5 and 10 {mu}m s{sup -1}), except for Al, all impurities are in concentrations below an important maximum limit for the feedstock of solar grade silicon. At the same mold velocities, the concentrations of Fe, Ti, Cu, Mn, and Ni measured at the bottom of the ingots obtained from both types of metallurgical silicon (typical

  13. Error bounds from extra precise iterative refinement

    Energy Technology Data Exchange (ETDEWEB)

    Demmel, James; Hida, Yozo; Kahan, William; Li, Xiaoye S.; Mukherjee, Soni; Riedy, E. Jason

    2005-02-07

    We present the design and testing of an algorithm for iterative refinement of the solution of linear equations, where the residual is computed with extra precision. This algorithm was originally proposed in the 1960s [6, 22] as a means to compute very accurate solutions to all but the most ill-conditioned linear systems of equations. However two obstacles have until now prevented its adoption in standard subroutine libraries like LAPACK: (1) There was no standard way to access the higher precision arithmetic needed to compute residuals, and (2) it was unclear how to compute a reliable error bound for the computed solution. The completion of the new BLAS Technical Forum Standard [5] has recently removed the first obstacle. To overcome the second obstacle, we show how a single application of iterative refinement can be used to compute an error bound in any norm at small cost, and use this to compute both an error bound in the usual infinity norm, and a componentwise relative error bound. We report extensive test results on over 6.2 million matrices of dimension 5, 10, 100, and 1000. As long as a normwise (resp. componentwise) condition number computed by the algorithm is less than 1/max{l_brace}10,{radical}n{r_brace} {var_epsilon}{sub w}, the computed normwise (resp. componentwise) error bound is at most 2 max{l_brace}10,{radical}n{r_brace} {center_dot} {var_epsilon}{sub w}, and indeed bounds the true error. Here, n is the matrix dimension and w is single precision roundoff error. For worse conditioned problems, we get similarly small correct error bounds in over 89.4% of cases.

  14. Essays on refining markets and environmental policy

    Science.gov (United States)

    Oladunjoye, Olusegun Akintunde

    This thesis is comprised of three essays. The first two essays examine empirically the relationship between crude oil price and wholesale gasoline prices in the U.S. petroleum refining industry while the third essay determines the optimal combination of emissions tax and environmental research and development (ER&D) subsidy when firms organize ER&D either competitively or as a research joint venture (RJV). In the first essay, we estimate an error correction model to determine the effects of market structure on the speed of adjustment of wholesale gasoline prices, to crude oil price changes. The results indicate that market structure does not have a strong effect on the dynamics of price adjustment in the three regional markets examined. In the second essay, we allow for inventories to affect the relationship between crude oil and wholesale gasoline prices by allowing them to affect the probability of regime change in a Markov-switching model of the refining margin. We find that low gasoline inventory increases the probability of switching from the low margin regime to the high margin regime and also increases the probability of staying in the high margin regime. This is consistent with the predictions of the competitive storage theory. In the third essay, we extend the Industrial Organization R&D theory to the determination of optimal environmental policies. We find that RJV is socially desirable. In comparison to competitive ER&D, we suggest that regulators should encourage RJV with a lower emissions tax and higher subsidy as these will lead to the coordination of ER&D activities and eliminate duplication of efforts while firms internalize their technological spillover externality.

  15. Texture evolution and enhanced grain refinement under high-pressure-double-torsion

    Energy Technology Data Exchange (ETDEWEB)

    Jahedi, Mohammad [Department of Mechanical Engineering, University of New Hampshire, Durham, NH 03824 (United States); Department of Materials Science and Engineering, School of Engineering, Shiraz University, Shiraz (Iran, Islamic Republic of); Paydar, Mohammad Hossein [Department of Materials Science and Engineering, School of Engineering, Shiraz University, Shiraz (Iran, Islamic Republic of); Zheng, Shijian [Materials Physics and Applications Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Beyerlein, Irene J. [Theoretical Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Knezevic, Marko, E-mail: marko.knezevic@unh.edu [Department of Mechanical Engineering, University of New Hampshire, Durham, NH 03824 (United States)

    2014-08-12

    We present a severe plastic deformation process called high-pressure-double-torsion (HPDT) for grain size refinement in metallic polycrystals. Like standard high-pressure torsion, HPDT monotonically imposes extreme plastic strains (⪢10) but via rotating both ends of the sample rather than one. Commercial purity Cu was subjected to HPT and HPDT for 1, 2, and 4 turns. The grain structure, hardness, and crystallographic texture were examined by transmission electron microscopy (TEM), Vickers microhardness tests, and X-ray diffraction (XRD) in both processes and compared in the mid-radius and at the edge of disks. We report that HPDT leads to finer grain sizes and higher hardness than HPT for the same number of turns. The measured textures exhibit typical shear components, which continuously strengthened with the plastic strain and also weakened with extreme grain refinement. These measurements also indicate that the texture gradients are lower in HPDT than HPT.

  16. 40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

    Science.gov (United States)

    2010-07-01

    ... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL... Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining... cane sugar into liquid refined sugar. ...

  17. A CSP Account of Event-B Refinement

    Directory of Open Access Journals (Sweden)

    Heike Wehrheim

    2011-06-01

    Full Text Available Event-B provides a flexible framework for stepwise system development via refinement. The framework supports steps for (a refining events (one-by-one, (b splitting events (one-by-many, and (c introducing new events. In each of the steps events can moreover possibly be anticipated or convergent. All such steps are accompanied with precise proof obligations. Still, it remains unclear what the exact relationship - in terms of a behaviour-oriented semantics - between an Event-B machine and its refinement is. In this paper, we give a CSP account of Event-B refinement, with a treatment for the first time of splitting events and of anticipated events. To this end, we define a CSP semantics for Event-B and show how the different forms of Event-B refinement can be captured as CSP refinement.

  18. Parallel adaptive mesh refinement for electronic structure calculations

    Energy Technology Data Exchange (ETDEWEB)

    Kohn, S.; Weare, J.; Ong, E.; Baden, S.

    1996-12-01

    We have applied structured adaptive mesh refinement techniques to the solution of the LDA equations for electronic structure calculations. Local spatial refinement concentrates memory resources and numerical effort where it is most needed, near the atomic centers and in regions of rapidly varying charge density. The structured grid representation enables us to employ efficient iterative solver techniques such as conjugate gradients with multigrid preconditioning. We have parallelized our solver using an object-oriented adaptive mesh refinement framework.

  19. A refinement methodology for object-oriented programs

    OpenAIRE

    Tafat , Asma; Boulmé , Sylvain; Marché , Claude

    2010-01-01

    International audience; Refinement is a well-known approach for developing correct-byconstruction software. It has been very successful for producing high quality code e.g., as implemented in the B tool. Yet, such refinement techniques are restricted in the sense that they forbid aliasing (and more generally sharing of data-structures), which often happens in usual programming languages. We propose a sound approach for refinement in presence of aliases. Suitable abstractions of programs are d...

  20. Institutions in OpenRefine: Cleaning up messes

    OpenAIRE

    Smith, Arthur

    2018-01-01

    OpenRefine (formerly Google Refine) is a tool for cleaning up messy data, but it is also well-suited to cross-linking different identifiers through their metadata entries. I will share some experiences in using OpenRefine to interlink GRID, ISNI, Wikidata, and our own internal institution identifiers. This matching process also highlights metadata errors (including duplicates and incorrect merges) in the different sources, and can help improve data quality on all sides. (Updated to full versi...

  1. Maintaining Information Flow Security under Refinement and Transformation

    OpenAIRE

    Seehusen, Fredrik; Stølen, Ketil

    2006-01-01

    - We address the problem of maintaining information flow security under refinement and transformation. To this end we define a schema for the specification of secure information flow properties and show that all security properties defined in the schema are preserved by a notion of refinement. Refinement is a process that requires human guidance and is in general not subject for automation. A transformation on the other hand, is an executable function mapping specifications to specificatio...

  2. Mirror of the refined topological vertex from a matrix model

    CERN Document Server

    Eynard, B

    2011-01-01

    We find an explicit matrix model computing the refined topological vertex, starting from its representation in terms of plane partitions. We then find the spectral curve of that matrix model, and thus the mirror symmetry of the refined vertex. With the same method we also find a matrix model for the strip geometry, and we find its mirror curve. The fact that there is a matrix model shows that the refined topological string amplitudes also satisfy the remodeling the B-model construction.

  3. Solving the Sophistication-Population Paradox of Game Refinement Theory

    OpenAIRE

    Xiong , Shuo; Tiwary , Parth ,; Iida , Hiroyuki

    2016-01-01

    Part 4: Short Papers; International audience; A mathematical model of game refinement was proposed based on uncertainty of game outcome. This model has been shown to be useful in measuring the entertainment element in the domains such as boardgames and sport games. However, game refinement theory has not been able to explain the correlation between the popularity of a game and the game refinement value. This paper introduces another aspect in the study of game entertainment, the concept of “a...

  4. New Process for Grain Refinement of Aluminum. Final Report; FINAL

    International Nuclear Information System (INIS)

    Megy, Joseph A.

    2000-01-01

    A new method of grain refining aluminum involving in-situ formation of boride nuclei in molten aluminum just prior to casting has been developed in the subject DOE program over the last thirty months by a team consisting of JDC, Inc., Alcoa Technical Center, GRAS, Inc., Touchstone Labs, and GKS Engineering Services. The Manufacturing process to make boron trichloride for grain refining is much simpler than preparing conventional grain refiners, with attendant environmental, capital, and energy savings. The manufacture of boride grain refining nuclei using the fy-Gem process avoids clusters, salt and oxide inclusions that cause quality problems in aluminum today

  5. Architectural Refinement for the Design of Survivable Systems

    National Research Council Canada - National Science Library

    Ellison, Robert

    2001-01-01

    This paper describes a process for systematically refining an enterprise system architecture to resist recognize and recover from deliberate, malicious attacks by applying reusable design primitives...

  6. New Process for Grain Refinement of Aluminum. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Joseph A. Megy

    2000-09-22

    A new method of grain refining aluminum involving in-situ formation of boride nuclei in molten aluminum just prior to casting has been developed in the subject DOE program over the last thirty months by a team consisting of JDC, Inc., Alcoa Technical Center, GRAS, Inc., Touchstone Labs, and GKS Engineering Services. The Manufacturing process to make boron trichloride for grain refining is much simpler than preparing conventional grain refiners, with attendant environmental, capital, and energy savings. The manufacture of boride grain refining nuclei using the fy-Gem process avoids clusters, salt and oxide inclusions that cause quality problems in aluminum today.

  7. Crystallographic refinement by simulated annealing: Application to crambin

    International Nuclear Information System (INIS)

    Bruenger, A.T.; Yale Univ., New Haven, CT; Harvard Univ., Cambridge, MA; Karplus, M.; Petsko, G.A.

    1989-01-01

    A detailed description of the method of crystallographic refinement by simulated annealing is presented. To test the method, it has been applied to a 1.5 A resolution X-ray structure of crambin. The dependence of the success of the simulated annealing protocol with respect to the temperature of the heating stage is discussed. Optimal success is achieved at relatively high temperatures. Regardless of the protocol used, the molecular-dynamics refined structure always yields an improved R factor compared with restrained least-squares refinement without manual re-fitting. The differences between the various refined structures and the corresponding electron density maps are discussed. (orig.)

  8. Refining clean fuels for the future

    International Nuclear Information System (INIS)

    Courty, P.; Gruson, J.F.

    2001-01-01

    To which extent transportation fuels will reasonably be changed in the coming years? LPG and natural gas are expected to challenge conventional fuels, hydrogen and methanol are bounded to possible fuel cells development. Among others, security of supply, competitive economics and environmental protection issues will be the key to the changes in the coming years. But taking into account expected transportation development, liquid fuels from oil should prevail as the reference energy. Though most of technologies and catalysts needed for the future are still existing or under marketing plans, the industry has to cope with the growing share of middle distillates. Indeed future zero heavy fuel-oil refineries are technically feasible through many existing and recent technologies. However their potential profitability is weighed down deeply by the very high investments and operating costs which are tied up. Tomorrow's main gasoline challenges deal with sulfur in FCC gasoline, aromatics and olefins contents together with a possible ban of ethers, hampering future octane demand and its technical feasibility. In a similar way diesel oil issues for the future imply a very deep desulfurization with possible aromatics hydrogenation and rings opening in order to comply with cetane and poly-aromatics ratings. Natural gas upgrading via syngas chemistry is still expected to open the way to clean fuels for the future via improved and integrated FT's GTL technologies which could as a matter provide most of future increases in clean fuels demand without decreasing the related fatal carbon losses as CO 2 . As an overall view, clean fuels production for the future is technically feasible. Advanced hydro-refining and hydro-conversion technologies open the way to clean fuels and allow the best flexibility in the gasoline/middle distillates ratio. However cost reduction remains a key issue since the huge investments needed are faced with low and volatile refining margins. In addition, CO 2

  9. Hydrogen in-situ refining method for preparing high purity gadolinium

    International Nuclear Information System (INIS)

    Li, Guoling; Li, Li; Fu, Kai; Wang, Chongyun; Zheng, Jie; Xu, Li; Tian, Wenhuai; Li, Xingguo

    2015-01-01

    The removal of non-metallic impurities, especially oxygen and nitrogen, from the rare-earth metal gadolinium (Gd) is challenging, due to their strong affinity to Gd metal. Herein we present an effective approach to prepare high purity Gd via a novel hydrogen in-situ refining method. The final concentrations of oxygen and nitrogen could be reduced to 30 and 19 mass ppm, respectively. The changes of lattice parameters were derived from XRD; enthalpy values and gaseous speciation associated with the gas–solid physiochemical reactions were determined through a combination of DSC/MS measurements and thermodynamic calculations. The results show that oxygen and nitrogen can be efficiently removed by degassing Gd with dissolved hydrogen. The underlying mechanism for the refinement is discussed systematically in this paper. - Highlights: • Hydrogen can shuttle gadolinium freely at high temperature. • The concentration of O and N dropped to 30 ppm and 19 ppm, respectively. • The hydrogen content could finally decrease to 17 ppm. • Hydrogen, water and ammonia signals can be detected successfully. • This method is environment friendly and no other recontaminations

  10. Hydrogen in-situ refining method for preparing high purity gadolinium

    Energy Technology Data Exchange (ETDEWEB)

    Li, Guoling [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Department of Materials Physics and Chemistry, University of Science and Technology Beijing, NO. 30, Xueyuan Road, Beijing 100083 (China); Li, Li [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Fu, Kai [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Department of Materials Physics and Chemistry, University of Science and Technology Beijing, NO. 30, Xueyuan Road, Beijing 100083 (China); Wang, Chongyun [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, NO. 30, Xueyuan Road, Beijing 100083 (China); Zheng, Jie [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Xu, Li [State Grid Smart Grid Research Institute, Future Science& Technology Park, Changping, Beijing 102211 (China); Tian, Wenhuai [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, NO. 30, Xueyuan Road, Beijing 100083 (China); Li, Xingguo, E-mail: xgli@pku.edu.cn [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China)

    2015-11-05

    The removal of non-metallic impurities, especially oxygen and nitrogen, from the rare-earth metal gadolinium (Gd) is challenging, due to their strong affinity to Gd metal. Herein we present an effective approach to prepare high purity Gd via a novel hydrogen in-situ refining method. The final concentrations of oxygen and nitrogen could be reduced to 30 and 19 mass ppm, respectively. The changes of lattice parameters were derived from XRD; enthalpy values and gaseous speciation associated with the gas–solid physiochemical reactions were determined through a combination of DSC/MS measurements and thermodynamic calculations. The results show that oxygen and nitrogen can be efficiently removed by degassing Gd with dissolved hydrogen. The underlying mechanism for the refinement is discussed systematically in this paper. - Highlights: • Hydrogen can shuttle gadolinium freely at high temperature. • The concentration of O and N dropped to 30 ppm and 19 ppm, respectively. • The hydrogen content could finally decrease to 17 ppm. • Hydrogen, water and ammonia signals can be detected successfully. • This method is environment friendly and no other recontaminations.

  11. Metal-metal-hofteproteser

    DEFF Research Database (Denmark)

    Ulrich, Michael; Overgaard, Søren; Penny, Jeannette

    2014-01-01

    In Denmark 4,456 metal-on-metal (MoM) hip prostheses have been implanted. Evidence demonstrates that some patients develope adverse biological reactions causing failures of MoM hip arthroplasty. Some reactions might be systemic. Failure rates are associated with the type and the design of the Mo...

  12. Determination of metallic impurities in metallic niobium by AAS and silicon by spectrophotometry

    International Nuclear Information System (INIS)

    Ayres, M.J.G.; Silva, G.L.J.P. da; Capri Neto, A.; Grallath, E.

    1988-01-01

    Niobium extraction in fluorhydric solution with methyl isobutyl ketone separates high quantities of refined metal from the impurities. The optimization of the extraction allows separate above 98% in 1000 mg of niobium. The preconcentration of the purified metal traces is get by this way, improving their determination by Atomic Absorption Spectroscopy. The spectrophotometric determination of silicon in metallic niobium, after the separation by distillation are also studied. (C.G.C.) [pt

  13. Study of matrix effect in determination of metals in re-refined basic oils by energy dispersive X-ray fluorescence - EDX; Estudo do efeito de matriz na determinação de metais em óleos básicos rerrefinados por fluorescência de raios-X por energia dispersiva

    Energy Technology Data Exchange (ETDEWEB)

    Melo, Maristela L. S., E-mail: mlsilva@anp.gov.br [Agência Nacional do Petróleo, Gás Natural e Biocombustíveis (ANP), Brasília, DF (Brazil); Souza, Jurandir R. de [Universidade de Brasília (UnB), Brasília, DF (Brazil). Instituto de Química

    2015-06-15

    In this article, the results of the study of the matrix effect in the determination of metals calcium, chromium, iron, nickel, copper, zinc, molybdenum, cadmium, barium and lead in base oil using Energy Dispersive X-Ray Fluorescence (EDX) are presented. Sensitivities obtained for each calibration curve were evaluated where calcium, chromium, copper, cadmium, barium and lead had the lowest sensitivities. In the case of cadmium, this parameter was lagging and the studies were not carried forward. The curves of the other metals in different base oils were evaluated for linearity. The elements chromium, copper, molybdenum and lead showed linearity problems in some cases. Therefore, curves in different base oils showed distinct mathematical behavior where the matrix effect was confirmed. The other curves were evaluated and existence of the matrix effect attributed to interference of C / H ratio was confirmed in the quantification of all elements. Metals iron, nickel and zinc exhibited the highest sensitivity and determination coefficients, showing that the method has application potential. (author)

  14. The Analysis of the Chloride and Fluoride Influences on the Reducer Refinement Processes (Carbo-N-Ox Aluminum Alloys

    Directory of Open Access Journals (Sweden)

    Bydałek A. W.

    2013-09-01

    Full Text Available Slag refining slag with west materials was analysed used the DTA methods. In the paper a method of determining the reduction capability, with the Carbo-N-Ox method, of slag solutions was used. Some relations between the stimulators in the environment - slag - metal system allow to initiate mass exchange reactions in the process of slag refining.The presented in work course of behaviour permits on choice of basic composition of slaglite, the of necessary components stimulating quantities, as well as on accomplishment of opinion of ability refinement. The worked out programme Slag-Prop, after introduction of data with experiment, it allows on next corrections in composition of proposed mixtures also, should be put on properly elaborated factors of multistage reaction with essential usage of suitable stimulators.

  15. Linear Prediction Using Refined Autocorrelation Function

    Directory of Open Access Journals (Sweden)

    M. Shahidur Rahman

    2007-07-01

    Full Text Available This paper proposes a new technique for improving the performance of linear prediction analysis by utilizing a refined version of the autocorrelation function. Problems in analyzing voiced speech using linear prediction occur often due to the harmonic structure of the excitation source, which causes the autocorrelation function to be an aliased version of that of the vocal tract impulse response. To estimate the vocal tract characteristics accurately, however, the effect of aliasing must be eliminated. In this paper, we employ homomorphic deconvolution technique in the autocorrelation domain to eliminate the aliasing effect occurred due to periodicity. The resulted autocorrelation function of the vocal tract impulse response is found to produce significant improvement in estimating formant frequencies. The accuracy of formant estimation is verified on synthetic vowels for a wide range of pitch frequencies typical for male and female speakers. The validity of the proposed method is also illustrated by inspecting the spectral envelopes of natural speech spoken by high-pitched female speaker. The synthesis filter obtained by the current method is guaranteed to be stable, which makes the method superior to many of its alternatives.

  16. Refining and blending of aviation turbine fuels.

    Science.gov (United States)

    White, R D

    1999-02-01

    Aviation turbine fuels (jet fuels) are similar to other petroleum products that have a boiling range of approximately 300F to 550F. Kerosene and No.1 grades of fuel oil, diesel fuel, and gas turbine oil share many similar physical and chemical properties with jet fuel. The similarity among these products should allow toxicology data on one material to be extrapolated to the others. Refineries in the USA manufacture jet fuel to meet industry standard specifications. Civilian aircraft primarily use Jet A or Jet A-1 fuel as defined by ASTM D 1655. Military aircraft use JP-5 or JP-8 fuel as defined by MIL-T-5624R or MIL-T-83133D respectively. The freezing point and flash point are the principle differences between the finished fuels. Common refinery processes that produce jet fuel include distillation, caustic treatment, hydrotreating, and hydrocracking. Each of these refining processes may be the final step to produce jet fuel. Sometimes blending of two or more of these refinery process streams are needed to produce jet fuel that meets the desired specifications. Chemical additives allowed for use in jet fuel are also defined in the product specifications. In many cases, the customer rather than the refinery will put additives into the fuel to meet their specific storage or flight condition requirements.

  17. FPGA Congestion-Driven Placement Refinement

    Energy Technology Data Exchange (ETDEWEB)

    Vicente de, J.

    2005-07-01

    The routing congestion usually limits the complete proficiency of the FPGA logic resources. A key question can be formulated regarding the benefits of estimating the congestion at placement stage. In the last years, it is gaining acceptance the idea of a detailed placement taking into account congestion. In this paper, we resort to the Thermodynamic Simulated Annealing (TSA) algorithm to perform a congestion-driven placement refinement on the top of the common Bounding-Box pre optimized solution. The adaptive properties of TSA allow the search to preserve the solution quality of the pre optimized solution while improving other fine-grain objectives. Regarding the cost function two approaches have been considered. In the first one Expected Occupation (EO), a detailed probabilistic model to account for channel congestion is evaluated. We show that in spite of the minute detail of EO, the inherent uncertainty of this probabilistic model impedes to relieve congestion beyond the sole application of the Bounding-Box cost function. In the second approach we resort to the fast Rectilinear Steiner Regions algorithm to perform not an estimation but a measurement of the global routing congestion. This second strategy allows us to successfully reduce the requested channel width for a set of benchmark circuits with respect to the widespread Versatile Place and Route (VPR) tool. (Author) 31 refs.

  18. Refining the ischemic penumbra with topography.

    Science.gov (United States)

    Thirugnanachandran, Tharani; Ma, Henry; Singhal, Shaloo; Slater, Lee-Anne; Davis, Stephen M; Donnan, Geoffrey A; Phan, Thanh

    2018-04-01

    It has been 40 years since the ischemic penumbra was first conceptualized through work on animal models. The topography of penumbra has been portrayed as an infarcted core surrounded by penumbral tissue and an extreme rim of oligemic tissue. This picture has been used in many review articles and textbooks before the advent of modern imaging. In this paper, we review our understanding of the topography of the ischemic penumbra from the initial experimental animal models to current developments with neuroimaging which have helped to further define the temporal and spatial evolution of the penumbra and refine our knowledge. The concept of the penumbra has been successfully applied in clinical trials of endovascular therapies with a time window as long as 24 h from onset. Further, there are reports of "good" outcome even in patients with a large ischemic core. This latter observation of good outcome despite having a large core requires an understanding of the topography of the penumbra and the function of the infarcted regions. It is proposed that future research in this area takes departure from a time-dependent approach to a more individualized tissue and location-based approach.

  19. Refined Pichia pastoris reference genome sequence

    Science.gov (United States)

    Sturmberger, Lukas; Chappell, Thomas; Geier, Martina; Krainer, Florian; Day, Kasey J.; Vide, Ursa; Trstenjak, Sara; Schiefer, Anja; Richardson, Toby; Soriaga, Leah; Darnhofer, Barbara; Birner-Gruenberger, Ruth; Glick, Benjamin S.; Tolstorukov, Ilya; Cregg, James; Madden, Knut; Glieder, Anton

    2016-01-01

    Strains of the species Komagataella phaffii are the most frequently used “Pichia pastoris” strains employed for recombinant protein production as well as studies on peroxisome biogenesis, autophagy and secretory pathway analyses. Genome sequencing of several different P. pastoris strains has provided the foundation for understanding these cellular functions in recent genomics, transcriptomics and proteomics experiments. This experimentation has identified mistakes, gaps and incorrectly annotated open reading frames in the previously published draft genome sequences. Here, a refined reference genome is presented, generated with genome and transcriptome sequencing data from multiple P. pastoris strains. Twelve major sequence gaps from 20 to 6000 base pairs were closed and 5111 out of 5256 putative open reading frames were manually curated and confirmed by RNA-seq and published LC-MS/MS data, including the addition of new open reading frames (ORFs) and a reduction in the number of spliced genes from 797 to 571. One chromosomal fragment of 76 kbp between two previous gaps on chromosome 1 and another 134 kbp fragment at the end of chromosome 4, as well as several shorter fragments needed re-orientation. In total more than 500 positions in the genome have been corrected. This reference genome is presented with new chromosomal numbering, positioning ribosomal repeats at the distal ends of the four chromosomes, and includes predicted chromosomal centromeres as well as the sequence of two linear cytoplasmic plasmids of 13.1 and 9.5 kbp found in some strains of P. pastoris. PMID:27084056

  20. Worldsheet Realization of the Refined Topological String

    CERN Document Server

    Antoniadis, I; Hohenegger, S; Narain, K S; Assi, A Zein

    2013-01-01

    A worldsheet realization of the refined topological string is proposed in terms of physical string amplitudes that compute generalized N=2 F-terms of the form F_{g,n} W^{2g}Y^{2n} in the effective supergravity action. These terms involve the chiral Weyl superfield W and a superfield Y defined as an N=2 chiral projection of a particular anti-chiral T-bar vector multiplet. In Heterotic and Type I theories, obtained upon compactification on the six-dimensional manifold K3xT2, T is the usual K\\"ahler modulus of the T2 torus. These amplitudes are computed exactly at the one-loop level in string theory. They are shown to reproduce the correct perturbative part of the Nekrasov partition function in the field theory limit when expanded around an SU(2) enhancement point of the string moduli space. The two deformation parameters epsilon_- and epsilon_+ of the Omega-supergravity background are then identified with the constant field-strength backgrounds for the anti-self-dual graviphoton and self-dual gauge field of the...

  1. Water Refining By the Membrane Separation Method

    Directory of Open Access Journals (Sweden)

    Zdenka Bolanca

    2000-03-01

    Full Text Available The investigations in this paper refer to the possibility of wastewater refining from deinking flotation process by the method of membrane separation. The offset impressions made with the conventional printing inks as wellas the models based on the raw materials of renewable origin were used in the recycling process. Before andafter the water treatment, the concentration of the sulphate, chloride, nitrate, total organic substance, oxygenconsumption, pH and electric conductivity was determinedin all the samples by standard analytical methods.The results point at the dependence of the concentration of the investigated inorganic and organic pollution with the characteristics of the prints used in the recycling process. The concentration decrease of the investigated pollution using the method of the membrane separation in relation to the boundary values of the water quality necessary for the paper production has been discussed. Besides the specific scientific contribution, the practical application of the investigation is the contribution to the closing of water circuit in paper production.

  2. Oil Production, Refining and Transportation in Canada

    Directory of Open Access Journals (Sweden)

    Igbal A. Guliyev

    2015-01-01

    Full Text Available The article deals with fuel and energy complex of Canada as one of the largest manufacturers of primary energy in the world, which provides up to 6 percent of the world energy supply. Only the Russian Federation, PRC, the United States of America and the Kingdom of Saudi Arabia have larger production volumes. However, oil plays the most significant role in Canada's energy exports. It is estimated that its proven reserves are sufficient to meet the demand for 140 years at current production rate. The relevance of the study, including the analysis of fuel and energy complex of Canada, is due to the fact that such comparison and synthesis of data on the amount of recoverable oil reserves, the volume of its production, imports, exports and transit of oil and oil products, the distribution of oil for transportation (via pipelines, rail, sea, road, strategic oil field, refining and transportation of oil and oil products development projects, as well as implementation of Canada's best practices in the Russian Federation, is being developed for the first time. In addition, the data given in previously published articles on the subject, due to the dynamic development of the industry, are obsolete and do not reflect the real situation.

  3. Metallated metal-organic frameworks

    Energy Technology Data Exchange (ETDEWEB)

    Bury, Wojciech; Farha, Omar K.; Hupp, Joseph T.; Mondloch, Joseph E.

    2017-02-07

    Porous metal-organic frameworks (MOFs) and metallated porous MOFs are provided. Also provided are methods of metallating porous MOFs using atomic layer deposition and methods of using the metallated MOFs as catalysts and in remediation applications.

  4. Metallated metal-organic frameworks

    Energy Technology Data Exchange (ETDEWEB)

    Bury, Wojciech; Farha, Omar K.; Hupp, Joseph T.; Mondloch, Joseph E.

    2017-08-22

    Porous metal-organic frameworks (MOFs) and metallated porous MOFs are provided. Also provided are methods of metallating porous MOFs using atomic layer deposition and methods of using the metallated MOFs as catalysts and in remediation applications.

  5. Investment in exploration-production and refining 2015

    International Nuclear Information System (INIS)

    Maisonnier, G.; Hureau, G.; Serbutoviez, S.; Silva, C.

    2016-01-01

    IFPEN analyses in this study the 2015 evolution of global investment in the field of exploration-production and refining: - Changes in oil and gas prices; - Investment in Exploration/Production: the end of an upward cycle; - Drilling and the global drilling market, upstream activities and markets; - 2015, a breath of fresh air for refining

  6. Refinement-Based Student Modeling and Automated Bug Library Construction.

    Science.gov (United States)

    Baffes, Paul; Mooney, Raymond

    1996-01-01

    Discussion of student modeling and intelligent tutoring systems focuses on the development of the ASSERT algorithm (Acquiring Stereotypical Student Errors by Refining Theories). Topics include overlay modeling; bug libraries (databases of student misconceptions); dynamic modeling; refinement-based modeling; and experimental results from tests at…

  7. The Development and Refinement of a Questionnaire on the ...

    African Journals Online (AJOL)

    The Development and Refinement of a Questionnaire on the Investigation of Students' Experience of First-Year Chemistry Practicals. ... refinement of a questionnaire for first-year Chemistry students. Three subscales were probed, namely affective attitudes, perceptions towards tutor effectiveness and outcomes achieved.

  8. Cavitation-aided grain refinement in aluminium alloys

    NARCIS (Netherlands)

    Atamanenko, T.V.

    2010-01-01

    This thesis deals with grain refinement under the influence of ultrasonic-driven cavitation in aluminium casting processes. Three major goals of this research were: (1) to identify the mechanism of the cavitation-aided grain refinement at different stages of solidification; (2) to reveal the

  9. Local grid refinement for free-surface flow simulations

    NARCIS (Netherlands)

    van der Plas, Peter

    2017-01-01

    The principal goal of the current study is to explore and investigate the potential of local grid refinement for increasing the numerical efficiency of free-surface flow simulations in a practical context. In this thesis we propose a method for local grid refinement in the free-surface flow model

  10. RBT—A Tool for Building Refined Buneman Trees

    DEFF Research Database (Denmark)

    Besenbacher, Søren; Mailund; Westh-Nielsen, Lasse

    2005-01-01

    We have developed a tool implementing an efficient algorithm for refined Buneman tree reconstruction. The algorithm—which has the same complexity as the neighbour-joining method and the (plain) Buneman tree construction—enables refined Buneman tree reconstruction on large taxa sets....

  11. Refined analysis results for multimedia network costs and profits

    DEFF Research Database (Denmark)

    Tahkokorpi, M.; Falch, Morten; Skouby, Knud Erik

    This deliverable describes the techno-economic business model developed in EURORIM WP3 and presents the refined results of the multimedia service delivery cost-profit calculations......This deliverable describes the techno-economic business model developed in EURORIM WP3 and presents the refined results of the multimedia service delivery cost-profit calculations...

  12. Mathematical aspects of Rietveld refinement and crystal structure ...

    Indian Academy of Sciences (India)

    Administrator

    Bond lengths and angles are calculated using the cell parameters. Using the Rietveld refinement parameters a stable PbTiO3 structure is suggested. Keywords. Rietveld; PbTiO3; XRD; oxides. 1. Introduction. Rietveld refinement technique is a standard treatment of powder diffraction data to make the final structural model.

  13. Grain refining efficiency of Al-Ti-C alloys

    International Nuclear Information System (INIS)

    Birol, Yuecel

    2006-01-01

    The problems associated with boride agglomeration and the poisoning effect of Zr in Zr-bearing alloys have created a big demand for boron-free grain refiners. The potential benefits of TiC as a direct nucleant for aluminium grains have thus generated a great deal of interest in TiC-bearing alloys in recent years. In Al-Ti-C grain refiners commercially available today, Al 3 Ti particles are introduced into the melt along with the TiC particles. Since the latter are claimed to nucleate α-Al directly, it is of great technological interest to see if reducing the Ti:C ratio further, i.e., increasing the C content of the grain refiner, will produce an increase in the grain refining efficiency of these alloys. A series of grain refiner samples with the Ti concentration fixed at 3% and a range of C contents between 0 and 0.75 were obtained by appropriately mixing an experimental Al-3Ti-0.75C alloy with Al-10Ti alloy and commercial purity aluminium. The grain refining efficiency of these grain refiners was assessed to investigate the role of the insoluble TiC and the soluble Al 3 Ti particles. The optimum chemistry for the Al-Ti-C grain refiners was also identified

  14. Grain refining efficiency of Al-Ti-C alloys

    Energy Technology Data Exchange (ETDEWEB)

    Birol, Yuecel [Materials Institute, Marmara Research Center, TUBITAK, 41470 Gebze, Kocaeli (Turkey)]. E-mail: yucel.birol@mam.gov.tr

    2006-09-28

    The problems associated with boride agglomeration and the poisoning effect of Zr in Zr-bearing alloys have created a big demand for boron-free grain refiners. The potential benefits of TiC as a direct nucleant for aluminium grains have thus generated a great deal of interest in TiC-bearing alloys in recent years. In Al-Ti-C grain refiners commercially available today, Al{sub 3}Ti particles are introduced into the melt along with the TiC particles. Since the latter are claimed to nucleate {alpha}-Al directly, it is of great technological interest to see if reducing the Ti:C ratio further, i.e., increasing the C content of the grain refiner, will produce an increase in the grain refining efficiency of these alloys. A series of grain refiner samples with the Ti concentration fixed at 3% and a range of C contents between 0 and 0.75 were obtained by appropriately mixing an experimental Al-3Ti-0.75C alloy with Al-10Ti alloy and commercial purity aluminium. The grain refining efficiency of these grain refiners was assessed to investigate the role of the insoluble TiC and the soluble Al{sub 3}Ti particles. The optimum chemistry for the Al-Ti-C grain refiners was also identified.

  15. Semi-solid rheocasting of grain refined aluminum alloy 7075

    CSIR Research Space (South Africa)

    Curle, UA

    2010-09-01

    Full Text Available Near-net shape rheocasting with the Council for Scientific and Industrial Research Rheo casting system(CSIR–RCS) and a high pressure die casting machine was successfully performed on Al–5Ti–1B grain refined aluminum alloy 7075. Grain refinement...

  16. Grain refinement of AZ31 magnesium alloy by electromagnetic ...

    Indian Academy of Sciences (India)

    ... effect on the grain size of AZ31 magnesium alloy under the effect of Al4C3 grain refiner. Electromagnetic stirring can `activate' the Al4C3 particles, resulting in more heterogeneous nucleation sites for the primary -Mg grains. But, longer holding time can `deactivate' the Al4C3 particles and poison the grain refining effect.

  17. Understanding Solidification Based Grain Refinement in Steels

    Science.gov (United States)

    2014-12-18

    Alumina Brick 42.2 52.6 1.4 2.3 0.2 0.3 Table 1 Composition of refractory materials The 99% alumina and 90% alumina samples showed no signs of reaction...dislocation can travel through a metal crystal before being blocked by a grain boundary. Since the dislocation is impeded sooner, the material cannot... thermomechanical methods for decreasing grain size. Steel castings are produced by making a mold using a pattern in the shape of the part. The pattern is removed

  18. Integration with U.S. refining

    International Nuclear Information System (INIS)

    Boslett, T.

    2007-01-01

    The production of crude in western Canada is expected to increase significantly in the next 10 to 15 years as the development of oil sands leases continues. In particular, large-scale investments by major oil sands producers have focused on upgrading bitumen to light synthetic crude oil. Major refinery projects in the United States will take advantage of substantially lower capital costs to increase bitumen processing capabilities. In addition, by 2008, new pipeline projects will provide western Canada with more export capacity. The BP Energy Company is investing US$3 billion to increase the refining capacity of Canadian heavy crude at its refinery in Whiting, Indiana, which already has pipeline connectivity and long-term product placement capabilities. The project, which is scheduled to begin in 2011, will increase heavy blend processing capability to 260 thousand barrels per day and produce more than 1.7 million gallons of motor fuel per day. BP's investment has focused on the hydrogen unit, gas oil hydrotreater, hydrotreater revamps, a coker, a modular sulfur recovery unit, a sour water stripper complex, and 62 miles of piping. The refinery in Indiana has an experienced workforce and a greater availability of labor than in western Canada. Production forecasts indicate varying levels of heavy and light production, depending on the amount of condensate imports available. The project team will ensure that the refinery can handle the various levels of total acid number (TAN), sulfur and solids contained in Canadian heavy oils. The project risks are associated with uncertainties regarding production growth and quality; inflation risk as developments costs continue to rise for projects in Alberta; and regulatory risk that can impact bitumen cost. tabs., figs

  19. Refining the Jurassic Magnetic Quiet Zone

    Science.gov (United States)

    Tominaga, M.; Tivery, M.; Sager, W. W.

    2016-12-01

    We present a coherent marine magnetic reversal record from the Pacific to refine the Jurassic Quiet Zone (JQZ). Our definitive magnetic anomaly record consists of high-resolution sea surface, mid-water (3-km level deep-towed), and near-bottom profiles (0.1-km to the seafloor) with the magnetic source layer constrained by gravity anomaly data and reflection and refraction seismics, all of which are newly collected during TN272 and SKQ2014S2 cruises. All magnetic anomaly data were corrected diurnal variations and the present-day ambient geomagnetic field. In comparing our three-level JQZ magnetic anomaly profiles with previous work in the Japanese lineations, we confirm a globally coherent anomaly sequence in the JQZ from M29 to M42, including the distinctive amplitude envelope decreasing back in time from M19 to M38, with a minimum at M41, and then increasing back in time. A strong similarity in the M37/M38 polarity attributes found both in magnetostratigraphic and marine magnetic records suggest that rapid magnetic reversals were occurring during the M38 time in the JQZ. Seismic and gravity profiles from the Hawaiian JQZ seafloor show late-stage Cretaceous volcanism thickening crust by up to 150% with extra melt emplaced at the Moho, and numerous sills and volcanic cones in the sediment and on the seafloor. The region of thickest crust in the Hawaiian lineation corridor coincides with the region of the lowest JQZ anomaly amplitudes, very similar to the Low Amplitude Zone of Japanese lineation sequence, suggesting that the JQZ anomaly character can represent changes in geomagnetic field intensity over time but is free of the effects of Cretaceous volcanic overprint. We conducted inversion modeling to establish polarity block models and to estimate reversal rates. Reversal rates are the highest during periods with the lowest anomaly amplitudes, indicating a unique period of geomagnetic field behavior in the Earth's history.

  20. Glueball masses from the refined Gribov propagator

    Energy Technology Data Exchange (ETDEWEB)

    Capri, M.A.L. [Universidade Federal Rural do Rio de Janeiro (UFRRJ), Seropedica, RJ (Brazil); Dudal, D.; Vandersickel, N. [Ghent University (Belgium); Gomez, A.J.; Guimaraes, M.S.; Lemes, V.E.R.; Sorella, S.P.; Tedesco, D.G. [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil)

    2011-07-01

    Full text: The quantum description of the non-abelian Yang-Mills theory at low energy scales is a long standing unsolved problem. This is a confining theory, meaning that the physical degrees of freedom are not described by the fundamental fields appearing in its defining action functional. The physical states are thus created by composite fields operators. In the pure Yang-Mills theory the fundamental, non-physical, excitations are the gluons and the physical states are named as glueballs and are created by gauge invariant operators. Recent results coming from lattice simulations of the Yang-Mills theory points to a gluon propagator which violates positivity and tends to a constant non-zero value at zero-momentum. The best fitting for this behavior is provided by a propagator whose analytic form describes the propagation of complex mass excitations, the so-called i-particles. These are supposed to be the low energy, confined, non-physical gluons. This propagator coincides with the one derived from the Refined Gribov-Zwanziger (RGZ) theory, which takes into account nonperturbative physics related to gauge copies and dimension two condensates. In this work we construct local, gauge invariant, composite operators with the quantum numbers of the lightest glueball states J{sup PC} = 0{sup ++}; 0{sup -+}; 2{sup ++}. The correlation functions of these operators are evaluated by employing a lattice input for the mass scales of the low energy RGZ gluon propagator. We obtain for the glueball masses, in the lowest order approximation, the values m{sub 0++} {approx} 1.96 GeV, m{sub 0-+} {approx} 2.19 GeV, m{sub 2++} {approx} 2.04 GeV, in the SU(3) case, all within a 20% range of the corresponding lattice values. We also recover the mass hierarchy m{sub 0++} < m{sub 2++} < m{sub 0-+}.(author)

  1. Dyadic wavelets and refinable functions on a half-line

    International Nuclear Information System (INIS)

    Protasov, V Yu; Farkov, Yu A

    2006-01-01

    For an arbitrary positive integer n refinable functions on the positive half-line R + are defined, with masks that are Walsh polynomials of order 2 n -1. The Strang-Fix conditions, the partition of unity property, the linear independence, the stability, and the orthonormality of integer translates of a solution of the corresponding refinement equations are studied. Necessary and sufficient conditions ensuring that these solutions generate multiresolution analysis in L 2 (R + ) are deduced. This characterizes all systems of dyadic compactly supported wavelets on R + and gives one an algorithm for the construction of such systems. A method for finding estimates for the exponents of regularity of refinable functions is presented, which leads to sharp estimates in the case of small n. In particular, all the dyadic entire compactly supported refinable functions on R + are characterized. It is shown that a refinable function is either dyadic entire or has a finite exponent of regularity, which, moreover, has effective upper estimates.

  2. Metal-metal-hofteproteser

    DEFF Research Database (Denmark)

    Ulrich, Michael; Overgaard, Søren; Penny, Jeannette

    2014-01-01

    In Denmark 4,456 metal-on-metal (MoM) hip prostheses have been implanted. Evidence demonstrates that some patients develope adverse biological reactions causing failures of MoM hip arthroplasty. Some reactions might be systemic. Failure rates are associated with the type and the design of the Mo......M hip implant. A Danish surveillance programme has been initiated addressing these problems....

  3. Precipitation behavior and grain refinement of burnishing Al-Zn-Mg alloy

    Directory of Open Access Journals (Sweden)

    Ce Pang

    2018-02-01

    Full Text Available Burnishing is a unique strengthening approach to improve the strength of surface layer and remains the ductility of the interior of metallic materials. In this work, burnishing treatment was employed to improve the surface microstructure of naturally aged Al-Zn-Mg alloys after solid solution. Transmission electron microscopy, high-resolution transmission electron microscopy, X-ray diffraction and nano-indentation were used to characterize the effects of the burnishing on the microstructures of surface layer and Guinier-Preston (GP zones. It was indicated that GP zones uniformly distributed and dispersed in the matrix before burnishing, and the amount of GP zones decreased dramatically after burnishing processing. Additionally, the grains in the surficial layer were refined into nano-crystals with an average grain size of 78 nm. Burnishing treatment not only led to formation of large number of dislocation substructures in the sub-surface and near-matrix surface, but also promoted the precipitation of metastable η' phase at grain boundaries. The synergistic effects of the grain refinement, dislocation multiplication and the precipitation of η' phase strengthen the burnished layer of Al-Zn-Mg alloy. Keywords: Al-Zn-Mg alloy, Burnishing, Nano-crystal, Precipitation, Grain refinement

  4. Structure and atomic correlations in molecular systems probed by XAS reverse Monte Carlo refinement

    Science.gov (United States)

    Di Cicco, Andrea; Iesari, Fabio; Trapananti, Angela; D'Angelo, Paola; Filipponi, Adriano

    2018-03-01

    The Reverse Monte Carlo (RMC) algorithm for structure refinement has been applied to x-ray absorption spectroscopy (XAS) multiple-edge data sets for six gas phase molecular systems (SnI2, CdI2, BBr3, GaI3, GeBr4, GeI4). Sets of thousands of molecular replicas were involved in the refinement process, driven by the XAS data and constrained by available electron diffraction results. The equilibrated configurations were analysed to determine the average tridimensional structure and obtain reliable bond and bond-angle distributions. Detectable deviations from Gaussian models were found in some cases. This work shows that a RMC refinement of XAS data is able to provide geometrical models for molecular structures compatible with present experimental evidence. The validation of this approach on simple molecular systems is particularly important in view of its possible simple extension to more complex and extended systems including metal-organic complexes, biomolecules, or nanocrystalline systems.

  5. Total antioxidant content of alternatives to refined sugar.

    Science.gov (United States)

    Phillips, Katherine M; Carlsen, Monica H; Blomhoff, Rune

    2009-01-01

    Oxidative damage is implicated in the etiology of cancer, cardiovascular disease, and other degenerative disorders. Recent nutritional research has focused on the antioxidant potential of foods, while current dietary recommendations are to increase the intake of antioxidant-rich foods rather than supplement specific nutrients. Many alternatives to refined sugar are available, including raw cane sugar, plant saps/syrups (eg, maple syrup, agave nectar), molasses, honey, and fruit sugars (eg, date sugar). Unrefined sweeteners were hypothesized to contain higher levels of antioxidants, similar to the contrast between whole and refined grain products. To compare the total antioxidant content of natural sweeteners as alternatives to refined sugar. The ferric-reducing ability of plasma (FRAP) assay was used to estimate total antioxidant capacity. Major brands of 12 types of sweeteners as well as refined white sugar and corn syrup were sampled from retail outlets in the United States. Substantial differences in total antioxidant content of different sweeteners were found. Refined sugar, corn syrup, and agave nectar contained minimal antioxidant activity (syrup, brown sugar, and honey showed intermediate antioxidant capacity (0.2 to 0.7 mmol FRAP/100 g). Based on an average intake of 130 g/day refined sugars and the antioxidant activity measured in typical diets, substituting alternative sweeteners could increase antioxidant intake an average of 2.6 mmol/day, similar to the amount found in a serving of berries or nuts. Many readily available alternatives to refined sugar offer the potential benefit of antioxidant activity.

  6. Segmental Refinement: A Multigrid Technique for Data Locality

    KAUST Repository

    Adams, Mark F.

    2016-08-04

    We investigate a domain decomposed multigrid technique, termed segmental refinement, for solving general nonlinear elliptic boundary value problems. We extend the method first proposed in 1994 by analytically and experimentally investigating its complexity. We confirm that communication of traditional parallel multigrid is eliminated on fine grids, with modest amounts of extra work and storage, while maintaining the asymptotic exactness of full multigrid. We observe an accuracy dependence on the segmental refinement subdomain size, which was not considered in the original analysis. We present a communication complexity analysis that quantifies the communication costs ameliorated by segmental refinement and report performance results with up to 64K cores on a Cray XC30.

  7. Oil refining and product marketing developments in southeast Asia

    International Nuclear Information System (INIS)

    Szabo, A.M.

    1992-01-01

    Views on the future are based on supplies from a relatively stable Middle East and continued economic growth in the southeast Asian and Pacific countries. Under these circumstances the oil market for the Association of Southeast Asian Nations (ASEAN) will expand considerably during the decade of the 90's. Pacific country demand, 5.92 MMB/D, in 1990 is likely to grow to 7.06 MMB/D in 2000. Regional production could supply about 40% of this. The Asia-Pacific shortage of refining capacity could lead to high regional refined product prices and health refining profit margins. (author)

  8. Effect of refining on quality and composition of sunflower oil

    OpenAIRE

    Pal, U. S.; Patra, R. K.; Sahoo, N. R.; Bakhara, C. K.; Panda, M. K.

    2014-01-01

    An experimental oil refining unit has been developed and tested for sunflower oil. Crude pressed sunflower oil obtained from a local oil mill was refined using chemical method by degumming, neutralization, bleaching and dewaxing. The quality and composition of crude and refined oil were analysed compared. Reduction in phosphorous content from 6.15 ppm to 0, FFA content from 1.1 to 0.24 % (oleic acid), peroxide value from 22.5 to 7.9 meq/kg, wax content from 1,420 to 200 ppm and colour absorba...

  9. Recycling of Aluminum from Fibre Metal Laminates

    NARCIS (Netherlands)

    Zhu, G.; Xiao, Y.; Yang, Y.; Wang, J.; Sun, B.; Boom, R.

    2012-01-01

    Recycling of aluminum alloy scrap obtained from delaminated fibre metal laminates (FMLs) was studied through high temperature refining in the presence of a salt flux. The aluminum alloy scrap contains approximately mass fraction w(Cu) = 4.4%, w(Mg) = 1.1% and w(Mn) = 0.6% (2024 aluminum alloy). The

  10. RETRACTED ARTICLE: Microstructural evolution of AA7449 aerospace alloy refined by intensive shearing

    Science.gov (United States)

    Haghayeghi, R.; Nastac, L.

    2012-10-01

    Many aerospace alloys are sensitive to their composition thus cannot be chemically grain refined. In addition, only 1% grain refiners can act as nuclei for refining the structure. In this paper, physical refinement by intensive shearing above liquidus as an alternative technique will be investigated for AA7449 aerospace alloy. The results can open a new gateway for aerospace industry for refining their microstructure.

  11. Architectural Refinement for the Design of Survivable Systems

    National Research Council Canada - National Science Library

    Ellison, Robert

    2001-01-01

    ...; that is, have no central administration and no unified security policy. The survivable architecture refinement is an iterative risk-driven process which adopts the structure of Boehm's Spiral Model Boehm 88...

  12. Pakistan stepping up expansion of refining, transportation sectors

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that Pakistan is taking steps to speed expansion of its refining and oil transportation infrastructure. While the country has made significant progress toward energy self-efficiency by boosting oil and gas production it still must modernize and expand an aging, inadequate refining sector to meet rapidly growing demand for refined products. Pakistan's government has disclosed plans to build two refineries in the country, one at Rawalpindi near a string of recent oil discoveries, the other somewhere in the southern part of the country, likely Karachi. At the same time, efforts are proceeding to upgrade Pakistan's refineries. In addition, Pakistani state companies continue to press joint ventures in refining and marketing with foreign companies and expand downstream ties with neighbors that are key oil and gas exporters

  13. The Refined Lecture Hall Theorem via Abacus Diagrams

    OpenAIRE

    Bradford, Laura; Harris, Meredith; Jones, Brant; Komarinski, Alex; Matson, Carly; O'Shea, Edwin

    2012-01-01

    Bousquet-M\\'elou & Eriksson's lecture hall theorem generalizes Euler's celebrated distinct-odd partition theorem. We present an elementary and transparent proof of a refined version of the lecture hall theorem using a simple bijection involving abacus diagrams.

  14. ADAPTIVE MODEL REFINEMENT FOR THE IONOSPHERE AND THERMOSPHERE

    Data.gov (United States)

    National Aeronautics and Space Administration — ADAPTIVE MODEL REFINEMENT FOR THE IONOSPHERE AND THERMOSPHERE ANTHONY M. D’AMATO∗, AARON J. RIDLEY∗∗, AND DENNIS S. BERNSTEIN∗∗∗ Abstract. Mathematical models of...

  15. Refined mapping of loss of heterozygosity in Chinese sporadic ...

    African Journals Online (AJOL)

    GREGORY

    2010-08-30

    loss of heterozygosity), the loss of one paternal or maternal allele at specific locus on tumor suppressor genes ... while genome-wide scan and refined mapping were .... (D) Non-informative cases: microsatellites instable (MSI).

  16. Rack gasoline and refining margins - wanted: a summer romance

    Energy Technology Data Exchange (ETDEWEB)

    1988-04-13

    For the first time since late 1987, apparent refining margins on the US benchmark crude oil (based on spot purchase prices) are virtually zero. This felicitous bit of news comes loaded with possibilities of positive (maybe even good.) margins in coming months, if the differential between crude buying prices and the value of the refined barrel continues to improve. What refiners in the US market are watching most closely right now are motorists. This issue also contains the following: (1) ED refining netback data for the US Gulf and Western Coasts, Rotterdam, and Singapore, prices for early April 1988; and (2) ED fuel price/tax series for countries of the Western Hemisphere, April 1988 edition. 5 figures, 5 tables.

  17. P-Refinement and P-Threads (Preprint)

    National Research Council Canada - National Science Library

    Dong, Steven; Karniadakis, George E

    2002-01-01

    ...]) in d dimensions, which is higher than lower-order methods. In this paper, we demonstrate that by employing multi-threading within MPI processes we manage to counter- balance the cost increase associated with P-refinement...

  18. Distributed successive refinement of multiview images using broadcast advantage.

    Science.gov (United States)

    Chen, Zichong; Barrenetxea, Guillermo; Vetterli, Martin

    2012-11-01

    In environmental monitoring applications, having multiple cameras focus on common scenery increases robustness of the system. To save energy based on user demand, successive refinement image coding is important, as it allows us to progressively request better image quality. By exploiting the broadcast nature and correlation between multiview images, we investigate a two-camera setup and propose a novel two-encoder successive refinement scheme which imitates a ping-pong game. For the bivariate Gaussian case, we prove that this scheme is successively refinable on the theoretical rate-distortion limit of distributed coding (Wagner surface) under arbitrary settings. For stereo-view images, we develop a practical successive refinement coding algorithm using the same idea. The simulation results show that this scheme operates close to the distributed coding bound.

  19. Determinants of profitability differences among major refiner/marketers

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    This report attempts to shed light on the factors affecting the differing profitabilities among companies, particularly, the effect of refinery upgrading, to contribute toward a better understanding of the performance of the domestic petroleum refining industry. The determinants of domestic refining-marketing profitability in the short run are evaluated. The focus is on those factors affecting the profitability of operations using the existing capital stock. Of particular interest is the effect on profitability of investments made for refinery upgrading. The refining-marketing segment is assumed to be operated to maximize profits of that segment rather than the profits of some other segment. The cost and financial data used in the analysis are proprietary line-of-business data from the FRS. The FRS provides detailed information on refining-marketing revenue, cost, income, and investment. The specific data used are discussed and key definitions provided later in this report. 14 refs., 1 fig., 2 tabs.

  20. Japan`s refiner/marketers headed for major shakeout

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-26

    Japan`s downstream oil industry is in a state of crisis and headed for a major shakeout. The major catalyst for this was a dramatic deregulation step during April 1996 that allowed refined petroleum product imports by non-refiners. The move, together with a sharp drop in refining margins, falling retail gasoline prices, and a service station sector on the brink of collapse, are all leading to massive changes in the way the country`s refiners and marketers do business. This paper reviews the collapse of corporate profits during this period of deregulation; the development of a new price system geared toward bringing the prices of gasoline, fuel oil, and kerosene into line with each other to offset the fall in gasoline prices; and industry restructuring including mergers, acquisitions, and marketing consolidation. The paper then makes predictions on the outcome of these changes on the Japanese oil industry.

  1. CITGO Petroleum Corporation and PDV Midwest Refining, LLC Settlement

    Science.gov (United States)

    CITGO Petroleum Corporation and PDV Midwest Refining, LLC (collectively, CITGO) have agreed to pay a $1,955,000 civil penalty, perform environmental projects totaling more than $2 million, and spend an estimated $42 million in injunctive relief to resolve.

  2. Production, Refining, Structural Characterization and Fermentability of Rice Husk Xylooligosaccharides

    NARCIS (Netherlands)

    Gullon, P.; Gonzales-Munoz, M.J.; Gool, van M.P.; Schols, H.A.; Hirsch, J.; Ebringerova, A.; Rarajo, J.C.

    2010-01-01

    Oligosaccharides produced by hydrothermal processing of rice husks (xylooligosaccharides and glucooligosaccharides) were refined by membrane processing (operating in diafiltration and concentration modes), subjected to xylanase treatment to reduce the average molar mass, and subjected to further

  3. Asian oil refining. Demand growth and deregulation - an uncertain future

    International Nuclear Information System (INIS)

    Sameer Nawaz.

    1996-01-01

    The objective of the report is to identify the most important features of the oil refining industry in Asia. Major developments in consumption patterns changes in regional importance of countries are discussed, highlighting potential future developments. The first chapter introduces the various refining processes and presents a simple model for the analysis of complex refineries. Chapter 2 examines the development of the Asian refining industry against a background of economic growth and analyses trends in consumption of all products in Asian countries. In Chapter 3, the key issues concerning the refining industry are examined, among them the forces driving consumption, including the importance of economic development, and electricity and transport demand. The importance of product imports and international trade is discussed, and the extent of government involvement and the effects of changing retail and market prices are analysed. Chapter 4 looks at the strategies that oil and gas companies are following in the Asian refining industry. Particular significance is attached to the vertical integration of the oil majors, Japanese and Middle Eastern oil companies. A brief overview of the importance of the petrochemical industry is presented. The countries of Asia that are involved in the refining industry are profiled in Chapter 5. The future trend in oil consumption is examined in Chapter 6. There follows a brief discussion of the plans to expand crude refining capacity in the various countries and a forecast of the state of overcapacity which will result. In the final chapter, brief profiles of some of the most important companies in the Asian refining industry are presented, discussing their major activities and future plans. (Author)

  4. A CSP Account of Event-B Refinement

    OpenAIRE

    Heike Wehrheim; Helen Treharne; Steve Schneider

    2011-01-01

    Event-B provides a flexible framework for stepwise system development via refinement. The framework supports steps for (a) refining events (one-by-one), (b) splitting events (one-by-many), and (c) introducing new events. In each of the steps events can moreover possibly be anticipated or convergent. All such steps are accompanied with precise proof obligations. Still, it remains unclear what the exact relationship - in terms of a behaviour-oriented semantics - between an Event-B machine and i...

  5. Refined Fuchs inequalities for systems of linear differential equations

    International Nuclear Information System (INIS)

    Gontsov, R R

    2004-01-01

    We refine the Fuchs inequalities obtained by Corel for systems of linear meromorphic differential equations given on the Riemann sphere. Fuchs inequalities enable one to estimate the sum of exponents of the system over all its singular points. We refine these well-known inequalities by considering the Jordan structure of the leading coefficient of the Laurent series for the matrix of the right-hand side of the system in the neighbourhood of a singular point

  6. Reverse mechanical after effect during hydrogenation of zone refined iron

    Energy Technology Data Exchange (ETDEWEB)

    Spivak, L.V.; Skryabina, N.E.; Kurmaeva, L.D.; Smirnov, L.V. (Permskij Gosudarstvennyj Univ. (USSR); AN SSSR, Sverdlovsk. Inst. Fiziki Metallov)

    1984-12-01

    The relationship between the process of hydrogenation and the reverse mechanical after effect (RMA) microplastic deformation in the zone refined iron has been studied. Metallographic investigations and mechanical testing of the samples hydrogenated under torsional strain have been performed. It is shown that in the zone refined iron the formation of voids responsible for irreversible hydrogen embrittlement does not occur, but the hydrogen-initiated RMA strain is conserved, i. e. the RMA effects are independent of the presence of discontinuities.

  7. Effect of refining on quality and composition of sunflower oil.

    Science.gov (United States)

    Pal, U S; Patra, R K; Sahoo, N R; Bakhara, C K; Panda, M K

    2015-07-01

    An experimental oil refining unit has been developed and tested for sunflower oil. Crude pressed sunflower oil obtained from a local oil mill was refined using chemical method by degumming, neutralization, bleaching and dewaxing. The quality and composition of crude and refined oil were analysed compared. Reduction in phosphorous content from 6.15 ppm to 0, FFA content from 1.1 to 0.24 % (oleic acid), peroxide value from 22.5 to 7.9 meq/kg, wax content from 1,420 to 200 ppm and colour absorbance value from 0.149 to 0.079 (in spectrophotometer at 460 nm) were observed from crude to refined oil. It was observed that refining did not have significant effect on fatty acid compositions as found in the percentage peak area in the GC-MS chromatogram. The percentage of unsaturated fatty acid in both the oils were recorded to be about 95 % containing 9-Octadecenoic acid (Oleic acid) and 11,14-Eicosadienoic acid (elongated form of linoleic acid). The research results will be useful to small entrepreneurs and farmers for refining of sunflower oil for better marketability.

  8. On macromolecular refinement at subatomic resolution with interatomic scatterers

    Energy Technology Data Exchange (ETDEWEB)

    Afonine, Pavel V., E-mail: pafonine@lbl.gov; Grosse-Kunstleve, Ralf W.; Adams, Paul D. [Lawrence Berkeley National Laboratory, One Cyclotron Road, BLDG 64R0121, Berkeley, CA 94720 (United States); Lunin, Vladimir Y. [Institute of Mathematical Problems of Biology, Russian Academy of Sciences, Pushchino 142290 (Russian Federation); Urzhumtsev, Alexandre [IGMBC, 1 Rue L. Fries, 67404 Illkirch and IBMC, 15 Rue R. Descartes, 67084 Strasbourg (France); Faculty of Sciences, Nancy University, 54506 Vandoeuvre-lès-Nancy (France); Lawrence Berkeley National Laboratory, One Cyclotron Road, BLDG 64R0121, Berkeley, CA 94720 (United States)

    2007-11-01

    Modelling deformation electron density using interatomic scatters is simpler than multipolar methods, produces comparable results at subatomic resolution and can easily be applied to macromolecules. A study of the accurate electron-density distribution in molecular crystals at subatomic resolution (better than ∼1.0 Å) requires more detailed models than those based on independent spherical atoms. A tool that is conventionally used in small-molecule crystallography is the multipolar model. Even at upper resolution limits of 0.8–1.0 Å, the number of experimental data is insufficient for full multipolar model refinement. As an alternative, a simpler model composed of conventional independent spherical atoms augmented by additional scatterers to model bonding effects has been proposed. Refinement of these mixed models for several benchmark data sets gave results that were comparable in quality with the results of multipolar refinement and superior to those for conventional models. Applications to several data sets of both small molecules and macromolecules are shown. These refinements were performed using the general-purpose macromolecular refinement module phenix.refine of the PHENIX package.

  9. Validation and refinement of the Millennium Criteria for atopic dermatitis.

    Science.gov (United States)

    Schram, Mandy E; Leeflang, Mariska M G; DEN Ottolander, Jan Paul S; Spuls, Phyllis I; Bos, Jan D

    2011-09-01

    There is no gold standard for a definite diagnosis of atopic dermatitis. For the time being, several lists of diagnostic criteria have been proposed, some of them in actual use. The Millennium Criteria have been proposed to diagnose atopic dermatitis and to differentiate it from atopiform dermatitis. Our aim was to further refine the Millennium Criteria into a manageable set that can differentiate between atopic and atopiform dermatitis and other entities. The hereby refined Millennium Criteria will be compared with the UK Working Party Criteria and the Hanifin & Rajka Criteria. Data of 210 included patients were used. After multiple logistic regression, a minimum set of five criteria was identified as best discriminators: (i) typical morphology; (ii) early age of onset; (iii) Dennie-Morgan fold; (iv) historical and (v) actual flexural involvement. The refined Millennium Criteria were constituted from these criteria. When comparing the different list for validity in diagnosing atopic dermatitis, the refined Millennium Criteria showed a sensitivity of 81.8% and a specificity of 98.8% compared to a sensitivity of 97.7% and specificity of 72.9% of the UK Criteria and a sensitivity of 100% and specificity of 48.8% of the Hanifin & Rajka Criteria. This refinement and validity study shows that the refined Millennium Criteria are a valid tool to diagnose atopic and atopiform dermatitis in a hospital-based setting and therefore could be incorporated in clinical practice and trials. © 2011 Japanese Dermatological Association.

  10. Refining and end use study of coal liquids

    International Nuclear Information System (INIS)

    1998-01-01

    Two direct coal liquids were evaluated by linear programming analysis to determine their value as petroleum refinery feedstock. The first liquid, DL1, was produced from bitiuminous coal using the Hydrocarbon Technologies, Inc.(HTI) two-stage hydrogenation process in Proof of Concept Run No.1, POC-1. The second liquid, DL2,was produced from sub-bituminous coal using a three-stage HTI process in Proof of Concept Run No. 2, POC-2; the third stage being a severe hydrogenation process. A linear programming (LP) model was developed which simulates a generic 150,000 barrel per day refinery in the Midwest U.S. Data from upgrading tests conducted on the coal liquids and related petroleum fractions in the pilot plant testing phase of the Refining and End Use Study was inputed into the model. The coal liquids were compared against a generic petroleum crude feedstock. under two scenarios. In the first scenario, it was assumed that the refinery capacity and product slate/volumes were fixed. The coal liquids would be used to replace a portion of the generic crude. The LP results showed that the DL1 material had essentially the same value as the generic crude. Due to its higher quality, the DL2 material had a value of approximately 0.60 $/barrel higher than the petroleum crude. In the second scenario, it was assumed that a market opportunity exists to increase production by one-third. This requires a refinery expansion. The feedstock for this scenario could be either 100% petroleum crude or a combination of petroleum crude and the direct coal liquids. Linear programming analysis showed that the capital cost of the refinery expansion was significantly less when coal liquids are utilized. In addition, the pilot plant testing showed that both of the direct coal liquids demonstrated superior catalytic cracking and naphtha reforming yields. Depending on the coal liquid flow rate, the value of the DL1 material was 2.5-4.0 $/barrel greater than the base petroleum crude, while the DL2

  11. Refinement of RAIM via Implementation of Implicit Euler Method

    International Nuclear Information System (INIS)

    Lee, Yoonhee; Kim, Han-Chul

    2016-01-01

    The first approach is a mechanistic approach which is used in LIRIC in which more than 200 reactions are modeled in detail. This approach enables to perform the detailed analysis. However, it requires huge computation burden. The other approach is a simplified model approach which is used in the IMOD, ASTEC/IODE, and etc. Recently, KINS has developed RAIM (Radio-Active Iodine chemistry Model) based on the simplified model approach. Since the numerical analysis module in RAIM is based on the explicit Euler method, there are major issues on the stability of the module. Therefore, implementation of a stable numerical method becomes essential. In this study, RAIM is refined via implementation of implicit Euler method in which the Newton method is used to find the solutions at each time step. The refined RAIM is tested by comparing to RAIM based on the explicit Euler method. In this paper, RAIM was refined by implementing the implicit Euler method. At each time step of the method in the refined RAIM, the reaction kinetics equations are solved by the Newton method in which elements of the Jacobian matrix are expressed analytically. With the results of OECD-BIP P10T2 test, the refined RAIM was compared to RAIM with the explicit Euler method. The refined RAIM shows better agreement with the experimental data than those from the explicit Euler method. For the rapid change of pH during the experiment, the refined RAIM gives more realistic changes in the concentrations of chemical species than those from the explicit Euler method. In addition, in terms of computing time, the refined RAIM shows comparable computing time to that with explicit Euler method. These comparisons are attributed to ⁓10 times larger time step size used in the implicit Euler method, even though computation burden at each time step in the refined RAIM is much higher than that of the explicit Euler method. Compared to the experimental data, the refined RAIM still shows discrepancy, which are attributed

  12. Electromyogram refinement using muscle synergy based regulation of uncertain information.

    Science.gov (United States)

    Min, Kyuengbo; Shin, Duk; Lee, Jongho; Kakei, Shinji

    2018-04-27

    Electromyogram signal (EMG) measurement frequently experiences uncertainty attributed to issues caused by technical constraints such as cross talk and maximum voluntary contraction. Due to these problems, individual EMGs exhibit uncertainty in representing their corresponding muscle activations. To regulate this uncertainty, we proposed an EMG refinement, which refines EMGs with regulating the contribution redundancy of the signals from EMGs to approximating torques through EMG-driven torque estimation (EDTE) using the muscular skeletal forward dynamic model. To regulate this redundancy, we must consider the synergistic contribution redundancy of muscles, including "unmeasured" muscles, to approximating torques, which primarily causes redundancy of EDTE. To suppress this redundancy, we used the concept of muscle synergy, which is a key concept of analyzing the neurophysiological regulation of contribution redundancy of muscles to exerting torques. Based on this concept, we designed a muscle-synergy-based EDTE as a framework for EMG refinement, which regulates the abovementioned uncertainty of individual EMGs in consideration of unmeasured muscles. In achieving the proposed EMG refinement, the most considerable point is to suppress a large change such as overestimation attributed to enhancement of the contribution of particular muscles to estimating torques. Therefore it is reasonable to refine EMGs by minimizing the change in EMGs. To evaluate this model, we used a Bland-Altman plot, which quantitatively evaluates the proportional bias of refined signals to EMGs. Through this evaluation, we showed that the proposed EDTE minimizes the bias while approximating torques. Therefore this minimization optimally regulates the uncertainty of EMGs and thereby leads to optimal EMG refinement. Copyright © 2018 Elsevier Ltd. All rights reserved.

  13. Validating metal binding sites in macromolecule structures using the CheckMyMetal web server

    Science.gov (United States)

    Zheng, Heping; Chordia, Mahendra D.; Cooper, David R.; Chruszcz, Maksymilian; Müller, Peter; Sheldrick, George M.

    2015-01-01

    Metals play vital roles in both the mechanism and architecture of biological macromolecules. Yet structures of metal-containing macromolecules where metals are misidentified and/or suboptimally modeled are abundant in the Protein Data Bank (PDB). This shows the need for a diagnostic tool to identify and correct such modeling problems with metal binding environments. The "CheckMyMetal" (CMM) web server (http://csgid.org/csgid/metal_sites/) is a sophisticated, user-friendly web-based method to evaluate metal binding sites in macromolecular structures in respect to 7350 metal binding sites observed in a benchmark dataset of 2304 high resolution crystal structures. The protocol outlines how the CMM server can be used to detect geometric and other irregularities in the structures of metal binding sites and alert researchers to potential errors in metal assignment. The protocol also gives practical guidelines for correcting problematic sites by modifying the metal binding environment and/or redefining metal identity in the PDB file. Several examples where this has led to meaningful results are described in the anticipated results section. CMM was designed for a broad audience—biomedical researchers studying metal-containing proteins and nucleic acids—but is equally well suited for structural biologists to validate new structures during modeling or refinement. The CMM server takes the coordinates of a metal-containing macromolecule structure in the PDB format as input and responds within a few seconds for a typical protein structure modeled with a few hundred amino acids. PMID:24356774

  14. WINCO Metal Recycle annual report, FY 1993

    Energy Technology Data Exchange (ETDEWEB)

    Bechtold, T.E. [ed.

    1993-12-01

    This report is a summary of the first year progress of the WINCO Metal Recycle Program. Efforts were directed towards assessment of radioactive scrap metal inventories, economics and concepts for recycling, technology development, and transfer of technology to the private sector. Seven DOE laboratories worked together to develop a means for characterizing scrap metal. Radioactive scrap metal generation rates were established for several of these laboratories. Initial cost estimates indicate that recycle may be preferable over burial if sufficient decontamination factors can be achieved during melt refining. Radiation levels of resulting ingots must be minimized in order to keep fabrication costs low. Industry has much of the expertise and capability to execute the recycling of radioactive scrap metal. While no single company can sort, melt, refine, roll and fabricate, a combination of two to three can complete this operation. The one process which requires development is in melt refining for removal of radionuclides other than uranium. WINCO is developing this capability in conjunction with academia and industry. This work will continue into FY-94.

  15. WINCO Metal Recycle annual report, FY 1993

    International Nuclear Information System (INIS)

    Bechtold, T.E.

    1993-12-01

    This report is a summary of the first year progress of the WINCO Metal Recycle Program. Efforts were directed towards assessment of radioactive scrap metal inventories, economics and concepts for recycling, technology development, and transfer of technology to the private sector. Seven DOE laboratories worked together to develop a means for characterizing scrap metal. Radioactive scrap metal generation rates were established for several of these laboratories. Initial cost estimates indicate that recycle may be preferable over burial if sufficient decontamination factors can be achieved during melt refining. Radiation levels of resulting ingots must be minimized in order to keep fabrication costs low. Industry has much of the expertise and capability to execute the recycling of radioactive scrap metal. While no single company can sort, melt, refine, roll and fabricate, a combination of two to three can complete this operation. The one process which requires development is in melt refining for removal of radionuclides other than uranium. WINCO is developing this capability in conjunction with academia and industry. This work will continue into FY-94

  16. Cooling curve analysis in binary Al-Cu alloys: Part II- Effect of Cooling Rate and Grain Refinement on The Thermal and Thermodynamic Characteristics

    Directory of Open Access Journals (Sweden)

    Mehdi Dehnavi

    2015-09-01

    Full Text Available The Al-Cu alloys have been widely used in aerospace, automobile, and airplane applications. Generally Al–Ti and Al–Ti–B master alloys are added to the aluminium alloys for grain refinement. The cooling curve analysis (CCA has been used extensively in metal casting industry to predict microstructure constituents, grain refinement and to calculate the latent heat of solidification. The aim of this study is to investigate the effect of cooling rate and grain refinement on the thermal and thermodynamic characteristics of Al-Cu alloys by cooling curve analysis. To do this, Al-Cu alloys containing 3.7, and 4.8 wt.% Cu were melted and solidified with 0.04, 0.19, 0.42, and 1.08 K/s cooling rates. The temperature of the samples was recorded using a K thermocouple and a data acquisition system connected to a PC. Some samples were Grain refined by Al-5Ti-1B to see the effect of grain refinement on the aforementioned properties. The results show that, in a well refined alloy, nucleation will occur in a shorter time, and a undercooling approximately decreases to zero. The other results show that, with considering the cooling rate being around 0.1 °C/s, the Newtonian method is efficient in calculating the latent heat of solidification.

  17. Use of intensity quotients and differences in absolute structure refinement

    International Nuclear Information System (INIS)

    Parsons, Simon; Flack, Howard D.; Wagner, Trixie

    2013-01-01

    Differences and quotients can be defined using Friedel pairs of reflections and applied in refinement to enable absolute structure to be determined precisely even for light atom crystal structures. Several methods for absolute structure refinement were tested using single-crystal X-ray diffraction data collected using Cu Kα radiation for 23 crystals with no element heavier than oxygen: conventional refinement using an inversion twin model, estimation using intensity quotients in SHELXL2012, estimation using Bayesian methods in PLATON, estimation using restraints consisting of numerical intensity differences in CRYSTALS and estimation using differences and quotients in TOPAS-Academic where both quantities were coded in terms of other structural parameters and implemented as restraints. The conventional refinement approach yielded accurate values of the Flack parameter, but with standard uncertainties ranging from 0.15 to 0.77. The other methods also yielded accurate values of the Flack parameter, but with much higher precision. Absolute structure was established in all cases, even for a hydrocarbon. The procedures in which restraints are coded explicitly in terms of other structural parameters enable the Flack parameter to correlate with these other parameters, so that it is determined along with those parameters during refinement

  18. The future of refining industry is in Asia

    International Nuclear Information System (INIS)

    Dupin, L.

    2010-01-01

    The decision of Total Group to close down the refining activity of its Flandres' site at Dunkerque (France) is a testimony of the deep restructuring that is affecting this sector. The migration of the refining activity towards Middle-East and Asia has started several years ago. The World capacities are increasing: in 2009 4.36 billion tons of petroleum products were refined in the world, representing a 1.9% rise with respect to 2008. 661 refineries exist in the world, among which 6 were inaugurated in 2009, 115 are located in Europe and 12 in France. The bad health of the European refining activity is beneficial to Middle and Asia where investments in new production capacities follow on from one another. From now to 2030, these areas will benefit from 70% of the worldwide investments compared to 11% only for Europe and North America. The decline of the European refining industry is directly linked to decay of the automotive fuel consumption and to the increase of the diesel fuel share with respect to gasoline. On the other hand, Asia, and in particular China and India, follow the exactly opposite trend thanks to their population and economic growths. Therefore, European oil companies try to invest in Asia and are looking for new production capacities in China and India. (J.S.)

  19. Adaptive mesh refinement for shocks and material interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Dai, William Wenlong [Los Alamos National Laboratory

    2010-01-01

    There are three kinds of adaptive mesh refinement (AMR) in structured meshes. Block-based AMR sometimes over refines meshes. Cell-based AMR treats cells cell by cell and thus loses the advantage of the nature of structured meshes. Patch-based AMR is intended to combine advantages of block- and cell-based AMR, i.e., the nature of structured meshes and sharp regions of refinement. But, patch-based AMR has its own difficulties. For example, patch-based AMR typically cannot preserve symmetries of physics problems. In this paper, we will present an approach for a patch-based AMR for hydrodynamics simulations. The approach consists of clustering, symmetry preserving, mesh continuity, flux correction, communications, management of patches, and load balance. The special features of this patch-based AMR include symmetry preserving, efficiency of refinement across shock fronts and material interfaces, special implementation of flux correction, and patch management in parallel computing environments. To demonstrate the capability of the AMR framework, we will show both two- and three-dimensional hydrodynamics simulations with many levels of refinement.

  20. IDENTIFICATION OF CATALYTIC METAL ION LIGANDS IN RIBOZYMES

    Science.gov (United States)

    Frederiksen, John K.; Piccirilli, Joseph A.

    2012-01-01

    Site-bound metal ions participate in the catalytic mechanisms of many ribozymes. Understanding these mechanisms therefore requires knowledge of the specific ligands on both substrate and ribozyme that coordinate these catalytic metal ions. A number of different structural and biochemical strategies have been developed and refined for identifying metal ion binding sites within ribozymes, and for assessing the catalytic contributions of the metal ions bound at those sites. We review these approaches and provide examples of their application, focusing in particular on metal ion rescue experiments and their roles in the construction of the transition state models for the Tetrahymena group I and RNase P ribozymes. PMID:19651216

  1. New metals

    International Nuclear Information System (INIS)

    Bergqvist, U.

    1983-12-01

    The aim of this report is to estimate the exposure to various metals and metal compounds and discuss the available information of the possible toxic effects of these metals and compounds. In the first section, some metals are defined as those with either a large or a fast increasing exposure to living organisms. The available information on toxicity is discussed in the second section. In the third section interesting metals are defined as compounds having a large exposure and an apparent insufficient knowledge of their possible toxic effects. Comments on each of these metals are also to be found in the third section. (G.B.)

  2. Zone refining of sintered, microwave-derived YBCO superconductors

    International Nuclear Information System (INIS)

    Warrier, K.G.K.; Varma, H.K.; Mani, T.V.; Damodaran, A.D.; Balachandran, U.

    1993-07-01

    Post-sintering treatments such as zone melting under thermal gradient has been conducted on sintered YBCO tape cast films. YBCO precursor powder was derived through decomposition of a mixture of nitrates of cations in a microwave oven for ∼4 min. The resulting powder was characterized and made into thin sheets by tape casting and then sintered at 945 C for 5 h. The sintered tapes were subjected to repeated zone refining operations at relatively high speeds of ∼30 mm/h. A microstructure having uniformly oriented grains in the a-b plane throughout the bulk of the sample was obtained by three repeated zone refining operations. Details of precursor preparation, microwave processing and its advantages, zone refining conditions, and microstructural features are presented in this paper

  3. Stability studies on refined soybean oil stored in various conditions

    International Nuclear Information System (INIS)

    Arawande, J.O.; Amoo, I.A.

    2008-01-01

    The 12 months stability study of freshly produced refined soybean oil revealed that refined soybean oil stored in plastic containers in dark was more hydrolytically and oxidatively stable than that stored in other containers in light condition. There was no significant difference at P < 0.05 in free fatty acids and acid value of oil stored under light and dark conditions in tin and glass containers but there was significant difference at P < 0.05 in peroxide value of oil stored in light and dark conditions in all the storage containers. Light increased the degree of oxidative rancidity of refined soybean oil, the most in tin containers, followed by glass containers and the least in plastic containers. (author)

  4. Future prospects for palm oil refining and modifications

    Directory of Open Access Journals (Sweden)

    Gibon Véronique

    2009-07-01

    Full Text Available Palm oil is rich in minor components that impart unique nutritional properties and need to be preserved. In this context, refining technologies have been improved, with the dual temperature deodorizer, the double condensing unit and the ice condensing system. The DOBI is a good tool to assess quality of the crude palm oil and its ability to be properly refined. Specially refined oils open a market for new high quality products (golden palm oil, red palm oil, white soaps, etc.. Palm oil is a good candidate for the multi-step dry fractionation process, aiming to the production of commodity oils and specialty fats (cocoa butter replacers. New technological developments allow quality and yield improvements. Palm oil and fractions are also valuable feedstock for enzymatic interesterification in which applications are for commodity oil (low-trans margarines and shortenings and for special products (cocoa butter equivalents, infant formulation, ….

  5. Error sensitivity to refinement: a criterion for optimal grid adaptation

    Science.gov (United States)

    Luchini, Paolo; Giannetti, Flavio; Citro, Vincenzo

    2017-12-01

    Most indicators used for automatic grid refinement are suboptimal, in the sense that they do not really minimize the global solution error. This paper concerns with a new indicator, related to the sensitivity map of global stability problems, suitable for an optimal grid refinement that minimizes the global solution error. The new criterion is derived from the properties of the adjoint operator and provides a map of the sensitivity of the global error (or its estimate) to a local mesh refinement. Examples are presented for both a scalar partial differential equation and for the system of Navier-Stokes equations. In the last case, we also present a grid-adaptation algorithm based on the new estimator and on the FreeFem++ software that improves the accuracy of the solution of almost two order of magnitude by redistributing the nodes of the initial computational mesh.

  6. Numerical solution of plasma fluid equations using locally refined grids

    International Nuclear Information System (INIS)

    Colella, P.

    1997-01-01

    This paper describes a numerical method for the solution of plasma fluid equations on block-structured, locally refined grids. The plasma under consideration is typical of those used for the processing of semiconductors. The governing equations consist of a drift-diffusion model of the electrons and an isothermal model of the ions coupled by Poisson's equation. A discretization of the equations is given for a uniform spatial grid, and a time-split integration scheme is developed. The algorithm is then extended to accommodate locally refined grids. This extension involves the advancement of the discrete system on a hierarchy of levels, each of which represents a degree of refinement, together with synchronization steps to ensure consistency across levels. A brief discussion of a software implementation is followed by a presentation of numerical results

  7. Trends in heavy oil production and refining in California

    International Nuclear Information System (INIS)

    Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II.

    1992-07-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10 degrees to 20 degrees API gravity) production in California has increased from 20% of the state's total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation's energy production and refining capability. California is the recipient and refines most of Alaska's 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources

  8. Risk as economic category: systematics scientific approach and refinement contents

    OpenAIRE

    V.G. Vygovskyy

    2015-01-01

    The paper studies the categorical-conceptual apparatus of risk and its refinement based on a critical analysis of existing systematic scientific approaches. Determined that in the refinement of the economic nature of the risk of a number of controversial issues: the definition of the objective or subjective nature of risk; matching of concepts such as «risk», «danger», «loss», «probability of loss»; definition of negative or positive consequences of risk; identification of risk with its conse...

  9. Quantum Refinement Does Not Support Dinuclear Copper Sites in Crystal Structures of Particulate Methane Monooxygenase.

    Science.gov (United States)

    Cao, Lili; Caldararu, Octav; Rosenzweig, Amy C; Ryde, Ulf

    2018-01-02

    Particulate methane monooxygenase (pMMO) is one of the few enzymes that can activate methane. The metal content of this enzyme has been highly controversial, with suggestions of a dinuclear Fe site or mono-, di-, or trinuclear Cu sites. Crystal structures have shown a mono- or dinuclear Cu site, but the resolution was low and the geometry of the dinuclear site unusual. We have employed quantum refinement (crystallographic refinement enhanced with quantum-mechanical calculations) to improve the structure of the active site. We compared a number of different mono- and dinuclear geometries, in some cases enhanced with more protein ligands or one or two water molecules, to determine which structure fits two sets of crystallographic raw data best. In all cases, the best results were obtained with mononuclear Cu sites, occasionally with an extra water molecule. Thus, we conclude that there is no crystallographic support for a dinuclear Cu site in pMMO. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. AMMOS2: a web server for protein-ligand-water complexes refinement via molecular mechanics.

    Science.gov (United States)

    Labbé, Céline M; Pencheva, Tania; Jereva, Dessislava; Desvillechabrol, Dimitri; Becot, Jérôme; Villoutreix, Bruno O; Pajeva, Ilza; Miteva, Maria A

    2017-07-03

    AMMOS2 is an interactive web server for efficient computational refinement of protein-small organic molecule complexes. The AMMOS2 protocol employs atomic-level energy minimization of a large number of experimental or modeled protein-ligand complexes. The web server is based on the previously developed standalone software AMMOS (Automatic Molecular Mechanics Optimization for in silico Screening). AMMOS utilizes the physics-based force field AMMP sp4 and performs optimization of protein-ligand interactions at five levels of flexibility of the protein receptor. The new version 2 of AMMOS implemented in the AMMOS2 web server allows the users to include explicit water molecules and individual metal ions in the protein-ligand complexes during minimization. The web server provides comprehensive analysis of computed energies and interactive visualization of refined protein-ligand complexes. The ligands are ranked by the minimized binding energies allowing the users to perform additional analysis for drug discovery or chemical biology projects. The web server has been extensively tested on 21 diverse protein-ligand complexes. AMMOS2 minimization shows consistent improvement over the initial complex structures in terms of minimized protein-ligand binding energies and water positions optimization. The AMMOS2 web server is freely available without any registration requirement at the URL: http://drugmod.rpbs.univ-paris-diderot.fr/ammosHome.php. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

  11. Metal lagging

    International Nuclear Information System (INIS)

    Lemercier, Guy.

    1974-01-01

    The metal lagging described is characterized by the fact that it is formed of closed sacks composed of an elastic metal mass, compressed in an outer envelope made of a fine mesh metal fabric. The metal mass is composed of stainless steel wool stuffed into the envelope. This lagging is particularly intended for the thermal protection of the end slab of LMFBR type reactors [fr

  12. Silicone metalization

    Energy Technology Data Exchange (ETDEWEB)

    Maghribi, Mariam N. (Livermore, CA); Krulevitch, Peter (Pleasanton, CA); Hamilton, Julie (Tracy, CA)

    2008-12-09

    A system for providing metal features on silicone comprising providing a silicone layer on a matrix and providing a metal layer on the silicone layer. An electronic apparatus can be produced by the system. The electronic apparatus comprises a silicone body and metal features on the silicone body that provide an electronic device.

  13. 40 CFR 80.1142 - What are the provisions for small refiners under the RFS program?

    Science.gov (United States)

    2010-07-01

    ... all of the following criteria: (i) The refiner produced gasoline at its refineries by processing crude... Standard § 80.1142 What are the provisions for small refiners under the RFS program? (a)(1) Gasoline produced by a refiner, or foreign refiner (as defined at § 80.1165(a)), is exempt from the renewable fuel...

  14. Refinement of the wedge bar technique for compression tests at intermediate strain rates

    Directory of Open Access Journals (Sweden)

    Stander M.

    2012-08-01

    Full Text Available A refined development of the wedge-bar technique [1] for compression tests at intermediate strain rates is presented. The concept uses a wedge mechanism to compress small cylindrical specimens at strain rates in the order of 10s−1 to strains of up to 0.3. Co-linear elastic impact principles are used to accelerate the actuation mechanism from rest to test speed in under 300μs while maintaining near uniform strain rates for up to 30 ms, i.e. the transient phase of the test is less than 1% of the total test duration. In particular, a new load frame, load cell and sliding anvil designs are presented and shown to significantly reduce the noise generated during testing. Typical dynamic test results for a selection of metals and polymers are reported and compared with quasistatic and split Hopkinson pressure bar results.

  15. Mechanical pulping with a sequential velocity refiner- a new concept

    Science.gov (United States)

    C.W. McMillin

    1978-01-01

    In previous research with refiner mechanical pulps, a theoretical stress analysis indicated that longitudinal tracheids of Pinus taeda L. fail while under torsional stress and unwind into ribbonlike elements that provide the coherence necessary for strength development. When macerated tracheids of loblolly pine were individually stressed in torsion...

  16. A Progressive Refinement Approach for the Visualisation of Implicit Surfaces

    Science.gov (United States)

    Gamito, Manuel N.; Maddock, Steve C.

    Visualising implicit surfaces with the ray casting method is a slow procedure. The design cycle of a new implicit surface is, therefore, fraught with long latency times as a user must wait for the surface to be rendered before being able to decide what changes should be introduced in the next iteration. In this paper, we present an attempt at reducing the design cycle of an implicit surface modeler by introducing a progressive refinement rendering approach to the visualisation of implicit surfaces. This progressive refinement renderer provides a quick previewing facility. It first displays a low quality estimate of what the final rendering is going to be and, as the computation progresses, increases the quality of this estimate at a steady rate. The progressive refinement algorithm is based on the adaptive subdivision of the viewing frustrum into smaller cells. An estimate for the variation of the implicit function inside each cell is obtained with an affine arithmetic range estimation technique. Overall, we show that our progressive refinement approach not only provides the user with visual feedback as the rendering advances but is also capable of completing the image faster than a conventional implicit surface rendering algorithm based on ray casting.

  17. Biomass refining for sustainable development : analysis and directions

    NARCIS (Netherlands)

    Luo, Lin

    2010-01-01

    To understand the contribution of biomass refining to sustainable development, the technical, environmental and economic aspects are summarized in this thesis. This work begins from life cycle assessment (LCA) of bioethanol from lignocellulosic feedstocks such as corn stover, sugarcane and bagasse,

  18. Discovery and refinement of loci associated with lipid levels

    NARCIS (Netherlands)

    Willer, Cristen J; Schmidt, Ellen M; Sengupta, Sebanti; Peloso, Gina M; Gustafsson, Stefan; Kanoni, Stavroula; Ganna, Andrea; Chen, Jin; Buchkovich, Martin L; Mora, Samia; Beckmann, Jacques S; Bragg-Gresham, Jennifer L; Chang, Hsing-Yi; Demirkan, Ayşe; Den Hertog, Heleen M; Do, Ron; Donnelly, Louise A; Ehret, Georg B; Esko, Tõnu; Feitosa, Mary F; Ferreira, Teresa; Fischer, Krista; Fontanillas, Pierre; Fraser, Ross M; Freitag, Daniel F; Gurdasani, Deepti; Heikkilä, Kauko; Hyppönen, Elina; Isaacs, Aaron; Jackson, Anne U; Johansson, Asa; Johnson, Toby; Kaakinen, Marika; Kettunen, Johannes; Kleber, Marcus E; Li, Xiaohui; Luan, Jian'an; Lyytikäinen, Leo-Pekka; Magnusson, Patrik K E; Mangino, Massimo; Mihailov, Evelin; Montasser, May E; Müller-Nurasyid, Martina; Nolte, Ilja M; O'Connell, Jeffrey R; Palmer, Cameron D; Perola, Markus; Petersen, Ann-Kristin; Sanna, Serena; Saxena, Richa; Service, Susan K; Shah, Sonia; Shungin, Dmitry; Sidore, Carlo; Song, Ci; Strawbridge, Rona J; Surakka, Ida; Tanaka, Toshiko; Teslovich, Tanya M; Thorleifsson, Gudmar; Van den Herik, Evita G; Voight, Benjamin F; Volcik, Kelly A; Waite, Lindsay L; Wong, Andrew; Wu, Ying; Zhang, Weihua; Absher, Devin; Asiki, Gershim; Barroso, Inês; Been, Latonya F; Bolton, Jennifer L; Bonnycastle, Lori L; Brambilla, Paolo; Burnett, Mary S; Cesana, Giancarlo; Dimitriou, Maria; Doney, Alex S F; Döring, Angela; Elliott, Paul; Epstein, Stephen E; Eyjolfsson, Gudmundur Ingi; Gigante, Bruna; Goodarzi, Mark O; Grallert, Harald; Gravito, Martha L; Groves, Christopher J; Hallmans, Göran; Hartikainen, Anna-Liisa; Hayward, Caroline; Hernandez, Dena; Hicks, Andrew A; Holm, Hilma; Hung, Yi-Jen; Illig, Thomas; Jones, Michelle R; Kaleebu, Pontiano; Kastelein, John J P; Khaw, Kay-Tee; Kim, Eric; Klopp, Norman; Komulainen, Pirjo; Kumari, Meena; Langenberg, Claudia; Lehtimäki, Terho; Lin, Shih-Yi; Lindström, Jaana; Loos, Ruth J F; Mach, François; McArdle, Wendy L; Meisinger, Christa; Mitchell, Braxton D; Müller, Gabrielle; Nagaraja, Ramaiah; Narisu, Narisu; Nieminen, Tuomo V M; Nsubuga, Rebecca N; Olafsson, Isleifur; Ong, Ken K; Palotie, Aarno; Papamarkou, Theodore; Pomilla, Cristina; Pouta, Anneli; Rader, Daniel J; Reilly, Muredach P; Ridker, Paul M; Rivadeneira, Fernando; Rudan, Igor; Ruokonen, Aimo; Samani, Nilesh; Scharnagl, Hubert; Seeley, Janet; Silander, Kaisa; Stancáková, Alena; Stirrups, Kathleen; Swift, Amy J; Tiret, Laurence; Uitterlinden, Andre G; van Pelt, L Joost; Vedantam, Sailaja; Wainwright, Nicholas; Wijmenga, Cisca; Wild, Sarah H; Willemsen, Gonneke; Wilsgaard, Tom; Wilson, James F; Young, Elizabeth H; Zhao, Jing Hua; Adair, Linda S; Arveiler, Dominique; Assimes, Themistocles L; Bandinelli, Stefania; Bennett, Franklyn; Bochud, Murielle; Boehm, Bernhard O; Boomsma, Dorret I; Borecki, Ingrid B; Bornstein, Stefan R; Bovet, Pascal; Burnier, Michel; Campbell, Harry; Chakravarti, Aravinda; Chambers, John C; Chen, Yii-Der Ida; Collins, Francis S; Cooper, Richard S; Danesh, John; Dedoussis, George; de Faire, Ulf; Feranil, Alan B; Ferrières, Jean; Ferrucci, Luigi; Freimer, Nelson B; Gieger, Christian; Groop, Leif C; Gudnason, Vilmundur; Gyllensten, Ulf; Hamsten, Anders; Harris, Tamara B; Hingorani, Aroon; Hirschhorn, Joel N; Hofman, Albert; Hovingh, G Kees; Hsiung, Chao Agnes; Humphries, Steve E; Hunt, Steven C; Hveem, Kristian; Iribarren, Carlos; Järvelin, Marjo-Riitta; Jula, Antti; Kähönen, Mika; Kaprio, Jaakko; Kesäniemi, Antero; Kivimaki, Mika; Kooner, Jaspal S; Koudstaal, Peter J; Krauss, Ronald M; Kuh, Diana; Kuusisto, Johanna; Kyvik, Kirsten O; Laakso, Markku; Lakka, Timo A; Lind, Lars; Lindgren, Cecilia M; Martin, Nicholas G; März, Winfried; McCarthy, Mark I; McKenzie, Colin A; Meneton, Pierre; Metspalu, Andres; Moilanen, Leena; Morris, Andrew D; Munroe, Patricia B; Njølstad, Inger; Pedersen, Nancy L; Power, Chris; Pramstaller, Peter P; Price, Jackie F; Psaty, Bruce M; Quertermous, Thomas; Rauramaa, Rainer; Saleheen, Danish; Salomaa, Veikko; Sanghera, Dharambir K; Saramies, Jouko; Schwarz, Peter E H; Sheu, Wayne H-H; Shuldiner, Alan R; Siegbahn, Agneta; Spector, Tim D; Stefansson, Kari; Strachan, David P; Tayo, Bamidele O; Tremoli, Elena; Tuomilehto, Jaakko; Uusitupa, Matti; van Duijn, Cornelia M; Vollenweider, Peter; Wallentin, Lars; Wareham, Nicholas J; Whitfield, John B; Wolffenbuttel, Bruce H R; Ordovas, Jose M; Boerwinkle, Eric; Palmer, Colin N A; Thorsteinsdottir, Unnur; Chasman, Daniel I; Rotter, Jerome I; Franks, Paul W; Ripatti, Samuli; Cupples, L Adrienne; Sandhu, Manjinder S; Rich, Stephen S; Boehnke, Michael; Deloukas, Panos; Kathiresan, Sekar; Mohlke, Karen L; Ingelsson, Erik; Abecasis, Gonçalo R

    2013-01-01

    Levels of low-density lipoprotein (LDL) cholesterol, high-density lipoprotein (HDL) cholesterol, triglycerides and total cholesterol are heritable, modifiable risk factors for coronary artery disease. To identify new loci and refine known loci influencing these lipids, we examined 188,577

  19. An approach of requirements tracing in formal refinement

    DEFF Research Database (Denmark)

    Jastram, Michael; Hallerstede, Stefan; Leuschel, Michael

    2010-01-01

    Formal modeling of computing systems yields models that are intended to be correct with respect to the requirements that have been formalized. The complexity of typical computing systems can be addressed by formal refinement introducing all the necessary details piecemeal. We report on preliminar...... changes, making use of corresponding techniques already built into the Event-B method....

  20. Procurement planning in oil refining industries considering blending operations

    DEFF Research Database (Denmark)

    Oddsdottir, Thordis Anna; Grunow, Martin; Akkerman, Renzo

    2013-01-01

    This paper addresses procurement planning in oil refining, which has until now only had limited attention in the literature. We introduce a mixed integer nonlinear programming (MINLP) model and develop a novel two-stage solution approach, which aims at computational efficiency while addressing th...

  1. Refining of crystal structures of macromolecules with molecular dynamics

    International Nuclear Information System (INIS)

    Mascarenhas, Y.P.

    1988-01-01

    In this work, the refining of crystal structures of macromolecules is discussed. The annealing method is employed and it can be previewed that, this method, will be largely used in the future for protein crystallography. (A.C.A.S.) [pt

  2. Evaluation of the acute toxicity of refined petroleum products against ...

    African Journals Online (AJOL)

    Static and static-renewal evaluation of the acute toxicity of three refined petroleum products — petrol, kerosene and diesel — against two freshwater animals, the mollusc Pila ovata and the fish Poecilia reticulata, was conducted in the laboratory. Petrol, kerosene and diesel were found to be moderately toxic to the test ...

  3. Assimilating Remote Ammonia Observations with a Refined Aerosol Thermodynamics Adjoint"

    Science.gov (United States)

    Ammonia emissions parameters in North America can be refined in order to improve the evaluation of modeled concentrations against observations. Here, we seek to do so by developing and applying the GEOS-Chem adjoint nested over North America to conductassimilation of observations...

  4. BioDegradation of Refined Petroleum Hydrocarbons in Soil | Obire ...

    African Journals Online (AJOL)

    Carbon-dioxide production and hydrocarbon degradation of refined petroleum hydrocarbon in soils treated with 5% gasoline, kerosene and diesel oil were investigated. Soil for study was bulked from around a car park in Port Harcourt. Soil samples were collected at weekly intervals for four weeks and subsequently at ...

  5. Macromolecular refinement by model morphing using non-atomic parameterizations.

    Science.gov (United States)

    Cowtan, Kevin; Agirre, Jon

    2018-02-01

    Refinement is a critical step in the determination of a model which explains the crystallographic observations and thus best accounts for the missing phase components. The scattering density is usually described in terms of atomic parameters; however, in macromolecular crystallography the resolution of the data is generally insufficient to determine the values of these parameters for individual atoms. Stereochemical and geometric restraints are used to provide additional information, but produce interrelationships between parameters which slow convergence, resulting in longer refinement times. An alternative approach is proposed in which parameters are not attached to atoms, but to regions of the electron-density map. These parameters can move the density or change the local temperature factor to better explain the structure factors. Varying the size of the region which determines the parameters at a particular position in the map allows the method to be applied at different resolutions without the use of restraints. Potential applications include initial refinement of molecular-replacement models with domain motions, and potentially the use of electron density from other sources such as electron cryo-microscopy (cryo-EM) as the refinement model.

  6. Use of intensity quotients and differences in absolute structure refinement

    Science.gov (United States)

    Parsons, Simon; Flack, Howard D.; Wagner, Trixie

    2013-01-01

    Several methods for absolute structure refinement were tested using single-crystal X-ray diffraction data collected using Cu Kα radiation for 23 crystals with no element heavier than oxygen: conventional refinement using an inversion twin model, estimation using intensity quotients in SHELXL2012, estimation using Bayesian methods in PLATON, estimation using restraints consisting of numerical intensity differences in CRYSTALS and estimation using differences and quotients in TOPAS-Academic where both quantities were coded in terms of other structural parameters and implemented as restraints. The conventional refinement approach yielded accurate values of the Flack parameter, but with standard uncertainties ranging from 0.15 to 0.77. The other methods also yielded accurate values of the Flack parameter, but with much higher precision. Absolute structure was established in all cases, even for a hydrocarbon. The procedures in which restraints are coded explicitly in terms of other structural parameters enable the Flack parameter to correlate with these other parameters, so that it is determined along with those parameters during refinement. PMID:23719469

  7. Nano-Sized Grain Refinement Using Friction Stir Processing

    Science.gov (United States)

    2013-03-01

    based on plastic deformation have been developed for grain refinement in Mg alloys such as rolling, Equal Channel Angular Processing ( ECAP ) and Equal...Research Laboratory. Introduction Magnesium ( Mg ) alloys have been widely used for structural components in the automotive, aerospace and...electronics industry due to their low density, high strength to stiffness ratio, good damping capacity, diecastability and recycling. However Mg alloys

  8. Refining in the 90s - a green burden?

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    The refining industry has been faced with many technical and economic challenges in recent years. Most of these changes have been a result of long-term strategic planning by governments, resulting in more stringent environmental legislation. This article discusses whether the industry can cope with the new rules. (author)

  9. Modelling of grain refinement driven by negative grain boundary energy

    Czech Academy of Sciences Publication Activity Database

    Fischer, F. D.; Zickler, G. A.; Svoboda, Jiří

    2017-01-01

    Roč. 97, č. 23 (2017), s. 1963-1977 ISSN 1478-6435 R&D Projects: GA ČR(CZ) GA15-06390S Institutional support: RVO:68081723 Keywords : grain refinement * grain nucleation * distribution concept * jump on distribution function Subject RIV: BJ - Thermodynamics OBOR OECD: Thermodynamics Impact factor: 1.505, year: 2016

  10. Synthesis and structure refinement of layered double hydroxides of ...

    Indian Academy of Sciences (India)

    Administrator

    )-oxygen bond in this compound as opposed to the Co–Ga hydroxide. These observations are supported by IR spectra. Keywords. Layered double hydroxide; Rietveld refinement; urea hydrolysis. 1. Introduction. The synthesis, structure and properties of layered double hydroxides (LDHs) have been widely studied in recent.

  11. On Architectural Support for Behaviour Refinement in Distributed Systems Design

    NARCIS (Netherlands)

    Quartel, Dick; Ferreira Pires, Luis; van Sinderen, Marten J.

    During the top-down design of distributed systems, abstract designs have to be replaced by more concrete designs, which add details that define how these systems can be implemented using available building blocks. Behaviour refinement is a design operation in which abstract behaviours are replaced

  12. On refinement of the unit simplex using regular simplices

    NARCIS (Netherlands)

    G.-Tóth, B.; Hendrix, E.M.T.; Casado, L.G.; García, I.

    2016-01-01

    A natural way to define branching in branch and bound (B&B) for blending problems is bisection. The consequence of using bisection is that partition sets are in general irregular. The question is how to use regular simplices in the refinement of the unit simplex. A regular simplex with fixed

  13. Significance of Kaduna River to Kaduna Refining and ...

    African Journals Online (AJOL)

    Significance of Kaduna River to Kaduna Refining and Petrochemicals Complex: Some Checks and Balances. ... Kaduna Refinery and Petrochemicals Complex comprises of various processing units. The plants produce various grades of petroleum ... contains a number of chemicals and compounds. The process waters are

  14. High resolution single particle refinement in EMAN2.1.

    Science.gov (United States)

    Bell, James M; Chen, Muyuan; Baldwin, Philip R; Ludtke, Steven J

    2016-05-01

    EMAN2.1 is a complete image processing suite for quantitative analysis of grayscale images, with a primary focus on transmission electron microscopy, with complete workflows for performing high resolution single particle reconstruction, 2-D and 3-D heterogeneity analysis, random conical tilt reconstruction and subtomogram averaging, among other tasks. In this manuscript we provide the first detailed description of the high resolution single particle analysis pipeline and the philosophy behind its approach to the reconstruction problem. High resolution refinement is a fully automated process, and involves an advanced set of heuristics to select optimal algorithms for each specific refinement task. A gold standard FSC is produced automatically as part of refinement, providing a robust resolution estimate for the final map, and this is used to optimally filter the final CTF phase and amplitude corrected structure. Additional methods are in-place to reduce model bias during refinement, and to permit cross-validation using other computational methods. Copyright © 2016 Elsevier Inc. All rights reserved.

  15. Refinements, Generalizations, and Applications of Jordan's Inequality and Related Problems

    Directory of Open Access Journals (Sweden)

    Feng Qi

    2009-01-01

    Full Text Available This is a survey and expository article. Some new developments on refinements, generalizations, and applications of Jordan's inequality and related problems, including some results about Wilker-Anglesio's inequality, some estimates for three kinds of complete elliptic integrals, and several inequalities for the remainder of power series expansion of the exponential function, are summarized.

  16. Challenges for Refinement and Composition of Instrumentations: Position Paper

    NARCIS (Netherlands)

    Ansaloni, D.; Binder, W.; Bockisch, Christoph; Bodden, E.; Hatun, Kardelen; Marek, L.; Qi, Z.; Sarimbekov, A.; Sewe, A.; Tuma, P.; Zheng, Y.

    Instrumentation techniques are widely used for implementing dynamic program analysis tools like profilers or debuggers. While there are many toolkits and frameworks to support the development of such low-level instrumentations, there is little support for the refinement or composition of

  17. Acetic acid based oil palm biomass refining process

    NARCIS (Netherlands)

    Harmsen, P.F.H.; Keijsers, E.R.P.; Lips, S.J.J.; Dam, van J.E.G.; Engelen-Smit, N.P.E.

    2011-01-01

    The invention relates to a process for refining a biomass from empty fruit bunches of oil palm with a dry matter content of 5-95 wt.%, based on the total wt. of the biomass, where the process comprises the subsequent stages of (a) water extn. under atm. pressure conditions and at pH of 5-7, (b) pre

  18. Production of biodiesel by transesterification of refined soybean oil ...

    African Journals Online (AJOL)

    This study focused on the production of biodiesel via transesterification of refined soybean oil obtained locally. Sodium hydroxide was used as the alkali catalyst and methanol (as alcohol) was used in the transesterification process due to its low cost. The methanol-to-oil molar ratio was maintained at 6:1. The effect of ...

  19. High purity tellurium production using dry refining processes

    Indian Academy of Sciences (India)

    purity) is purified using dry processes such as selective vapourization and zone melting in a thoroughly etched and cleaned quartz boat, under continuous flow of hydrogen (H2) gas. The tellurium ingot was quadruple zone refined (QZR) under continuous flow of H2 gas. Thus, the purified tellurium of ultra high purity (UHP) ...

  20. Orthogonal bases of radial functions for charge density refinements

    International Nuclear Information System (INIS)

    Restori, R.

    1990-01-01

    Charge density determination from X-ray measurements necessitates the evaluation of the Fourier-Bessel transforms of the radial functions used to expand the charge density. Analytical expressions are given here for four sets of orthogonal functions which can substitute for the 'traditional exponential functions' set in least-squares refinements. (orig.)

  1. Mathematical aspects of Rietveld refinement and crystal structure ...

    Indian Academy of Sciences (India)

    Administrator

    Abstract. The core mathematics, goodness-of-fit parameters of Rietveld refinement technique is introduced for structural analysis of crystalline materials not available as single crystals. X-ray diffraction (XRD) pat- terns of PbTiO3 compound prepared by following solid-state route, suggests it to be in single crystal form. All.

  2. effect of chemical refining on citrullus colocynthis and

    African Journals Online (AJOL)

    d

    2012-05-03

    May 3, 2012 ... having a good color, no taste or smell and remains fit for consumption, storage and transportation for long time .... can settle out during shipment or storage of pure oil [14, 16]. Alkali refining. For alkali .... produce biodiesel with high cloud and pour point that have poor cold performance. [24]. So P. pinnata oil ...

  3. Imports on the rise - small refiners looking for protection

    Energy Technology Data Exchange (ETDEWEB)

    Patrick, L.

    1985-04-01

    Small refiners, hurting from foreign competition, have launched a drive in Washington for oil products quotas or higher tariffs. Such protectionism would cost consumers a few cent per gallon, but they believe that it would be a good investment from a national security basis. Other developments in Congress and the Reagan Administration relating to the fuel oil industry are discussed.

  4. Simultaneous refinement of two components of an exsolution intergrowth

    DEFF Research Database (Denmark)

    Topa, Dan; Petricek, Vaclav; Dusek, Michal

    2008-01-01

    Crystal structures of intergrown lindstromite and krupkaite were determined in two distinct samples by a simultaneous crystal-structure refinement using a modified JANA program package. The exsolution intergrowths have a bulk composition, determined by means of electron microprobe, equal to bd(60...

  5. Crystal structure of vanadite: Refinement of anisotropic displacement parameters

    Czech Academy of Sciences Publication Activity Database

    Laufek, F.; Skála, Roman; Haloda, J.; Císařová, I.

    2006-01-01

    Roč. 51, 3-4 (2006), s. 271-275 ISSN 1210-8197 Institutional research plan: CEZ:AV0Z30130516 Keywords : anisotropic displacement parameter * crystal structure * single-crystal X-ray refinement * vanadinite Subject RIV: DB - Geology ; Mineralogy

  6. Refinement of a Chemistry Attitude Measure for College Students

    Science.gov (United States)

    Xu, Xiaoying; Lewis, Jennifer E.

    2011-01-01

    This work presents the evaluation and refinement of a chemistry attitude measure, Attitude toward the Subject of Chemistry Inventory (ASCI), for college students. The original 20-item and revised 8-item versions of ASCI (V1 and V2) were administered to different samples. The evaluation for ASCI had two main foci: reliability and validity. This…

  7. Action Relations. Basic Design Concepts for Behaviour Modelling and Refinement.

    NARCIS (Netherlands)

    Quartel, Dick

    This thesis presents basic design concepts, design methods and a basic design language for distributed system behaviours. This language is based on two basic concepts: the action concept and the causality relation concept. Our methods focus on behaviour refinement, which consists of replacing an

  8. Disparity refinement process based on RANSAC plane fitting for ...

    African Journals Online (AJOL)

    ... more accurate than normal flow state-of-the-art stereo matching algorithms. The performance evaluations are based on standard image quality metrics i.e. structural similarity index measure, peak signal-to-noise ratio and mean square error. Keywords: computer vision; disparity refinement; image segmentation; RANSAC; ...

  9. Genomic multiple sequence alignments: refinement using a genetic algorithm

    Directory of Open Access Journals (Sweden)

    Lefkowitz Elliot J

    2005-08-01

    Full Text Available Abstract Background Genomic sequence data cannot be fully appreciated in isolation. Comparative genomics – the practice of comparing genomic sequences from different species – plays an increasingly important role in understanding the genotypic differences between species that result in phenotypic differences as well as in revealing patterns of evolutionary relationships. One of the major challenges in comparative genomics is producing a high-quality alignment between two or more related genomic sequences. In recent years, a number of tools have been developed for aligning large genomic sequences. Most utilize heuristic strategies to identify a series of strong sequence similarities, which are then used as anchors to align the regions between the anchor points. The resulting alignment is globally correct, but in many cases is suboptimal locally. We describe a new program, GenAlignRefine, which improves the overall quality of global multiple alignments by using a genetic algorithm to improve local regions of alignment. Regions of low quality are identified, realigned using the program T-Coffee, and then refined using a genetic algorithm. Because a better COFFEE (Consistency based Objective Function For alignmEnt Evaluation score generally reflects greater alignment quality, the algorithm searches for an alignment that yields a better COFFEE score. To improve the intrinsic slowness of the genetic algorithm, GenAlignRefine was implemented as a parallel, cluster-based program. Results We tested the GenAlignRefine algorithm by running it on a Linux cluster to refine sequences from a simulation, as well as refine a multiple alignment of 15 Orthopoxvirus genomic sequences approximately 260,000 nucleotides in length that initially had been aligned by Multi-LAGAN. It took approximately 150 minutes for a 40-processor Linux cluster to optimize some 200 fuzzy (poorly aligned regions of the orthopoxvirus alignment. Overall sequence identity increased only

  10. Nucleation mechanisms of refined alpha microstructure in beta titanium alloys

    Science.gov (United States)

    Zheng, Yufeng

    Due to a great combination of physical and mechanical properties, beta titanium alloys have become promising candidates in the field of chemical industry, aerospace and biomedical materials. The microstructure of beta titanium alloys is the governing factor that determines their properties and performances, especially the size scale, distribution and volume fraction of precipitate phase in parent phase matrix. Therefore in order to enhance the performance of beta titanium alloys, it is critical to obtain a thorough understanding of microstructural evolution in beta titanium alloys upon various thermal and/or mechanical processes. The present work is focusing on the study of nucleation mechanisms of refined alpha microstructure and super-refined alpha microstructure in beta titanium alloys in order to study the influence of instabilities within parent phase matrix on precipitates nucleation, including compositional instabilities and/or structural instabilities. The current study is primarily conducted in Ti-5Al-5Mo-5V-3Cr (wt%, Ti-5553), a commercial material for aerospace application. Refined and super-refined precipitates microstructure in Ti-5553 are obtained under specific accurate temperature controlled heat treatments. The characteristics of either microstructure are investigated in details using various characterization techniques, such as SEM, TEM, STEM, HRSTEM and 3D atom probe to describe the features of microstructure in the aspect of morphology, distribution, structure and composition. Nucleation mechanisms of refined and super-refined precipitates are proposed in order to fully explain the features of different precipitates microstructure in Ti-5553. The necessary thermodynamic conditions and detailed process of phase transformations are introduced. In order to verify the reliability of proposed nucleation mechanisms, thermodynamic calculation and phase field modeling simulation are accomplished using the database of simple binary Ti-Mo system

  11. The use of Fourier reverse transforms in crystallographic phase refinement

    Energy Technology Data Exchange (ETDEWEB)

    Ringrose, Sharon [Iowa State Univ., Ames, IA (United States)

    1997-10-08

    Often a crystallographer obtains an electron density map which shows only part of the structure. In such cases, the phasing of the trial model is poor enough that the electron density map may show peaks in some of the atomic positions, but other atomic positions are not visible. There may also be extraneous peaks present which are not due to atomic positions. A method for determination of crystal structures that have resisted solution through normal crystallographic methods has been developed. PHASER is a series of FORTRAN programs which aids in the structure solution of poorly phased electron density maps by refining the crystallographic phases. It facilitates the refinement of such poorly phased electron density maps for difficult structures which might otherwise not be solvable. The trial model, which serves as the starting point for the phase refinement, may be acquired by several routes such as direct methods or Patterson methods. Modifications are made to the reverse transform process based on several assumptions. First, the starting electron density map is modified based on the fact that physically the electron density map must be non-negative at all points. In practice a small positive cutoff is used. A reverse Fourier transform is computed based on the modified electron density map. Secondly, the authors assume that a better electron density map will result by using the observed magnitudes of the structure factors combined with the phases calculated in the reverse transform. After convergence has been reached, more atomic positions and less extraneous peaks are observed in the refined electron density map. The starting model need not be very large to achieve success with PHASER; successful phase refinement has been achieved with a starting model that consists of only 5% of the total scattering power of the full molecule. The second part of the thesis discusses three crystal structure determinations.

  12. Hirshfeld atom refinement for modelling strong hydrogen bonds.

    Science.gov (United States)

    Woińska, Magdalena; Jayatilaka, Dylan; Spackman, Mark A; Edwards, Alison J; Dominiak, Paulina M; Woźniak, Krzysztof; Nishibori, Eiji; Sugimoto, Kunihisa; Grabowsky, Simon

    2014-09-01

    High-resolution low-temperature synchrotron X-ray diffraction data of the salt L-phenylalaninium hydrogen maleate are used to test the new automated iterative Hirshfeld atom refinement (HAR) procedure for the modelling of strong hydrogen bonds. The HAR models used present the first examples of Z' > 1 treatments in the framework of wavefunction-based refinement methods. L-Phenylalaninium hydrogen maleate exhibits several hydrogen bonds in its crystal structure, of which the shortest and the most challenging to model is the O-H...O intramolecular hydrogen bond present in the hydrogen maleate anion (O...O distance is about 2.41 Å). In particular, the reconstruction of the electron density in the hydrogen maleate moiety and the determination of hydrogen-atom properties [positions, bond distances and anisotropic displacement parameters (ADPs)] are the focus of the study. For comparison to the HAR results, different spherical (independent atom model, IAM) and aspherical (free multipole model, MM; transferable aspherical atom model, TAAM) X-ray refinement techniques as well as results from a low-temperature neutron-diffraction experiment are employed. Hydrogen-atom ADPs are furthermore compared to those derived from a TLS/rigid-body (SHADE) treatment of the X-ray structures. The reference neutron-diffraction experiment reveals a truly symmetric hydrogen bond in the hydrogen maleate anion. Only with HAR is it possible to freely refine hydrogen-atom positions and ADPs from the X-ray data, which leads to the best electron-density model and the closest agreement with the structural parameters derived from the neutron-diffraction experiment, e.g. the symmetric hydrogen position can be reproduced. The multipole-based refinement techniques (MM and TAAM) yield slightly asymmetric positions, whereas the IAM yields a significantly asymmetric position.

  13. Determination of Heavy Metal Levels in Edible Salt

    Directory of Open Access Journals (Sweden)

    Heshmati

    2014-09-01

    Full Text Available Background Edible salt is the most commonly used food additive worldwide. Therefore, any contamination of table salt could be a health hazard. Objectives The present study aimed to determine the levels of heavy metals in table and bakery refined salts. Materials and Methods Eighty-one table refined salt samples and the same number of bakery refined salt samples were purchased from retail market in the province of Hamadan, Iran. The levels of lead (Pb, cadmium (Cd, mercury (Hg, copper (Cu, and iron (Fe were determined using atomic absorption spectroscopy method. Results The levels (mean ± SD, μg/g of Pb, Cd, Hg, Cu, Fe in table refined salt samples were 0.852 ± 0.277, 0.229 ± 0.012, 0.054 ± 0.040, 1.25 ± 0.245 and 0.689 ± 1.58, respectively. The results for the same metals in bakery refined salt samples were as follows (mean ± SD, μg/g: 22 ± 0.320 for Pb, 0.240 ± 0.018 for Cd, 0.058 ± 0.007 for Hg, 1.89 ± 0.218 for Cu, and 8.75 ± 2.10 for Fe. Heavy metal concentrations were generally higher in bakery refined salt. Conclusions The results obtained in the present study were compared with the literature and legal limits. All values for these metals in the table and bakery refined salts were lower than the permitted consumption level defined by Codex (2 µg/g of Pb, 0.5 µg/g of Cd, 0.1 µg/g of Hg, and 2 µg/g of Cu.

  14. 40 CFR 80.551 - How does a refiner obtain approval as a small refiner under this subpart?

    Science.gov (United States)

    2010-07-01

    ...) Applications for motor vehicle diesel fuel small refiner status must be submitted to EPA by December 31, 2001...-operational between January 1, 1999, and January 1, 2000, the application for motor vehicle diesel fuel small...: (1) For motor vehicle diesel fuel small refiners— (i) A listing of the name and address of each...

  15. Role of manganese on the grain refining efficiency of AZ91D magnesium alloy refined by Al4C3

    International Nuclear Information System (INIS)

    Liu Shengfa; Zhang Yuan; Han Hui

    2010-01-01

    A novel Mg-50% Al 4 C 3 (hereafter in wt.%) master alloy has been developed by powder in situ synthesis process, the role of manganese on the grain refining efficiency of AZ91D magnesium alloy refined by this master alloy has been investigated. X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDS) results show the existence of Al 4 C 3 particles in this master alloy. After addition of 0.6% Al 4 C 3 or combined addition of 0.6% Al 4 C 3 and 0.27% Mn, the average grain size of AZ91D decreased dramatically from 360 μm to 210 μm, and from 360 μm to130 μm, respectively. However, no further refinement of grain size was achieved with additional amount of Mn exceeding 0.27% for AZ91D alloy refined by 0.6% Al 4 C 3 in the present investigation. Al-C-O-Mn-Fe-rich intermetallic particles with an Al-C-O-rich coating film, often observed in the central region of magnesium grains of the AZ91D alloy treated by the combination of Al 4 C 3 and Mn, are proposed to be the potent nucleating substrates for primary α-Mg.

  16. Basic effects of pulp refining on fiber properties--a review.

    Science.gov (United States)

    Gharehkhani, Samira; Sadeghinezhad, Emad; Kazi, Salim Newaz; Yarmand, Hooman; Badarudin, Ahmad; Safaei, Mohammad Reza; Zubir, Mohd Nashrul Mohd

    2015-01-22

    The requirement for high quality pulps which are widely used in paper industries has increased the demand for pulp refining (beating) process. Pulp refining is a promising approach to improve the pulp quality by changing the fiber characteristics. The diversity of research on the effect of refining on fiber properties which is due to the different pulp sources, pulp consistency and refining equipment has interested us to provide a review on the studies over the last decade. In this article, the influence of pulp refining on structural properties i.e., fibrillations, fine formation, fiber length, fiber curl, crystallinity and distribution of surface chemical compositions is reviewed. The effect of pulp refining on electrokinetic properties of fiber e.g., surface and total charges of pulps is discussed. In addition, an overview of different refining theories, refiners as well as some tests for assessing the pulp refining is presented. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Metallic nanomesh

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Zhifeng; Sun, Tianyi; Guo, Chuanfei

    2018-02-20

    A transparent flexible nanomesh having at least one conductive element and sheet resistance less than 300.OMEGA./.quadrature. when stretched to a strain of 200% in at least one direction. The nanomesh is formed by depositing a sacrificial film, depositing, etching, and oxidizing a first metal layer on the film, etching the sacrificial film, depositing a second metal layer, and removing the first metal layer to form a nanomesh on the substrate.

  18. VLSI metallization

    CERN Document Server

    Einspruch, Norman G; Gildenblat, Gennady Sh

    1987-01-01

    VLSI Electronics Microstructure Science, Volume 15: VLSI Metallization discusses the various issues and problems related to VLSI metallization. It details the available solutions and presents emerging trends.This volume is comprised of 10 chapters. The two introductory chapters, Chapter 1 and 2 serve as general references for the electrical and metallurgical properties of thin conducting films. Subsequent chapters review the various aspects of VLSI metallization. The order of presentation has been chosen to follow the common processing sequence. In Chapter 3, some relevant metal deposition tec

  19. The Direct Observation of Grain Refinement Mechanism in Advanced Multicomponent γ-TiAl Based Structural Intermetallics Doped with Boron

    Science.gov (United States)

    Kartavykh, A. V.; Gorshenkov, M. V.; Podgorny, D. A.

    The synthesis of Ti-44Al-5Nb-2Cr-1.5Zr-0.4B-0.07La and Ti-44Al-5Nb-1Cr-1.5Zr-1B-0.17La (at.%) intermetallic alloys was performed from pure metals by the electron beam semi-continuous casting technique. Alloys are characterized by convoluted microstructure whose refinement is progressive with the boron content increase. The specimens were analyzed using JEOL JSM6610 scanning electron microscope (SEM ) equipped with electron backscatter diffraction and energy dispersive X-ray spectroscopy (EDX ) systems. The boron alloying causes precipitation of micro-dimensional complex (Ti,Nb)B borides within solidifying melt. These particles-inoculants promote the formation of finer microstructure. Auger spectrometry was applied for quantitative elemental analysis of borides, using PHI-680 device. It was proven that the origin of structure refinement consists in solid-phase seeding and germination of α2-Ti3Al-phase on (Ti,Nb)B ribbon-like colonies with subsequent growth of α2-laths through the volumetrically prevailing γ-TiAl domains. We fixed several consecutive stages of microstructure refinement process. The description of these stages is supported with the dimensional, crystallographic and compositional characterization of microstructural constituents. The work provides a basis for new techniques of microstructure/mechanical properties engineering of studied materials.

  20. refining device for helium coolants capable of continuous tritium recovery for use with HTGR type reactors

    International Nuclear Information System (INIS)

    Tone, Hirohito.

    1981-01-01

    Purpose: To separate and recover hydrogen and tritium from helium coolants by a device comprising a tritium permeable metal film, a gas compressor and a recovery store container. Constitution: Impurity gas-containing helium sent from a primary helium coolant circuit exit of an HTGR type reactor to a helium refining system is introduced by way of a high temperature heat exchanger, a gas recycling device and a medium temperature heat exchanger to an absorber bed filled with absorber, where H 2 O and CO 2 in the impurity gas-containing helium are removed. Then, Kr, Xe, Ar, O 2 , N 2 , CO, CH 3 are removed and the remaining impurities, tritium and hydrogen, are introduced via each of heat exchangers into a tritium absorber bed. Then, they are permeated through a tritium permeable metal film, transferred to the low pressure side of a tritium permeation device and then compressed and stored in a tritium recovery store container by a gas compressor connected to the low pressure side. (Seki, T.)

  1. Study on a Salt Evaporation of the Uranium Deposits from an Electro-refiner

    International Nuclear Information System (INIS)

    Sung Bin Park; Dong Wook Cho; Gyu Hwan Oh; Jong Hyeon Lee; Sung Chan Hwang; Young Ho Kang; Han Soo Lee; Eung Ho Kim; Seong Won Park

    2008-01-01

    Uranium metal is electrodeposited onto a solid cathode during the electrorefining process. Uranium deposits from an electro-refiner contain about 30∼40 wt% salts. In order to recover pure uranium and transform it into metal ingots, the salts have to be removed. A salt distiller is adapted for a salt evaporation. A batch operation for the salt removal is carried out by a heating and vacuum evaporation. It is operated at 700 ∼ 1000 deg. C and less than 1 Torr, respectively. The behaviors of the salt evaporations were investigated by focusing on the effects of the vacuum pressure and the holding temperature on the salt distillation. The salt removal efficiencies were obtained with regards to the operational conditions. The Hertz-Langmuir relation was applied to the experimental results of the salt evaporations. The effective evaporation coefficients of the relation were obtained with regards to the operational conditions. The lower the vacuum pressure and the higher the holding temperature were, the higher the removal efficiencies of the salts were. (authors)

  2. Refinement and standardization of synthetic biological parts and devices.

    Science.gov (United States)

    Canton, Barry; Labno, Anna; Endy, Drew

    2008-07-01

    The ability to quickly and reliably engineer many-component systems from libraries of standard interchangeable parts is one hallmark of modern technologies. Whether the apparent complexity of living systems will permit biological engineers to develop similar capabilities is a pressing research question. We propose to adapt existing frameworks for describing engineered devices to biological objects in order to (i) direct the refinement and use of biological 'parts' and 'devices', (ii) support research on enabling reliable composition of standard biological parts and (iii) facilitate the development of abstraction hierarchies that simplify biological engineering. We use the resulting framework to describe one engineered biological device, a genetically encoded cell-cell communication receiver named BBa_F2620. The description of the receiver is summarized via a 'datasheet' similar to those widely used in engineering. The process of refinement and characterization leading to the BBa_F2620 datasheet may serve as a starting template for producing many standardized genetically encoded objects.

  3. Probing the moduli dependence of refined topological amplitudes

    Directory of Open Access Journals (Sweden)

    I. Antoniadis

    2015-12-01

    Full Text Available With the aim of providing a worldsheet description of the refined topological string, we continue the study of a particular class of higher derivative couplings Fg,n in the type II string effective action compactified on a Calabi–Yau threefold. We analyse first order differential equations in the anti-holomorphic moduli of the theory, which relate the Fg,n to other component couplings. From the point of view of the topological theory, these equations describe the contribution of non-physical states to twisted correlation functions and encode an obstruction for interpreting the Fg,n as the free energy of the refined topological string theory. We investigate possibilities of lifting this obstruction by formulating conditions on the moduli dependence under which the differential equations simplify and take the form of generalised holomorphic anomaly equations. We further test this approach against explicit calculations in the dual heterotic theory.

  4. Segmental Refinement: A Multigrid Technique for Data Locality

    Energy Technology Data Exchange (ETDEWEB)

    Adams, Mark [Columbia Univ., New York, NY (United States). Applied Physics and Applied Mathematics Dept.; Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2014-10-27

    We investigate a technique - segmental refinement (SR) - proposed by Brandt in the 1970s as a low memory multigrid method. The technique is attractive for modern computer architectures because it provides high data locality, minimizes network communication, is amenable to loop fusion, and is naturally highly parallel and asynchronous. The network communication minimization property was recognized by Brandt and Diskin in 1994; we continue this work by developing a segmental refinement method for a finite volume discretization of the 3D Laplacian on massively parallel computers. An understanding of the asymptotic complexities, required to maintain textbook multigrid efficiency, are explored experimentally with a simple SR method. A two-level memory model is developed to compare the asymptotic communication complexity of a proposed SR method with traditional parallel multigrid. Performance and scalability are evaluated with a Cray XC30 with up to 64K cores. We achieve modest improvement in scalability from traditional parallel multigrid with a simple SR implementation.

  5. Biodiesel obtained from soapstock originated in a refining oil industry

    International Nuclear Information System (INIS)

    Tobio Pérez, Indira; Díaz Domínguez, Yosvany; Piloto-Rodríguez, Ramón

    2017-01-01

    In the vegetable oil chemical refining process is obtained a by-product commonly named as soapstock, due to its physical and aspect properties. The soapstock free fatty acid content can reach to 50%. The present work shows a survey of researches focused on biodiesel obtaining from this by-product. The biodiesel is obtained following different routes and catalyzers features. A variety of reports shown the effectivity of the use of this by-product derived from vegetable oil refining industry to produce biodiesel. Several studies are addressed to the acid oil recovering involving processes without soapstock acidulation, with the aim of lowering costs and finding more attractive yields closing to the concept of zero wastes. (author)

  6. Unit-cell refinement from powder diffraction scans

    International Nuclear Information System (INIS)

    Pawley, G.S.

    1981-01-01

    A procedure for the refinement of the crystal unit cell from a powder diffraction scan is presented. In this procedure knowledge of the crystal structure is not required, and at the end of the refinement a list of indexed intensities is produced. This list may well be usable as the starting point for the application of direct methods. The problems of least-squares ill-conditioning due to overlapping reflections are overcome by constraints. An example using decafluorocyclohexene, C 6 F 10 , shows the quality of fit obtained in a case which may even be a false minimum. The method should become more relevant as powder scans of improved resolution become available, through the use of pulsed neutron sources. (Auth.)

  7. Bitumen to refined products and petrochemicals : a preliminary assessment

    International Nuclear Information System (INIS)

    Crandall, G.

    2004-01-01

    Purvin and Gertz is an energy consulting firm that provides advise to the energy sector. A review of western Canadian crude oil supply suggests that oil sands production will surpass declining conventional production. Oil sands supply includes synthetic crude oil (SCO), bitumen and diluent. It is expected that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. This presentation reviewed the potential of Alberta's oil sands and presented a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. In particular, the author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. tabs., figs

  8. Grain refinement of high strength steels to improve cryogenic toughness

    Science.gov (United States)

    Rush, H. F.

    1985-01-01

    Grain-refining techniques using multistep heat treatments to reduce the grain size of five commercial high-strength steels were investigated. The goal of this investigation was to improve the low-temperature toughness as measured by Charpy V-notch impact test without a significant loss in tensile strength. The grain size of four of five alloys investigated was successfully reduced up to 1/10 of original size or smaller with increases in Charpy impact energy of 50 to 180 percent at -320 F. Tensile properties were reduced from 0 to 25 percent for the various alloys tested. An unexpected but highly beneficial side effect from grain refining was improved machinability.

  9. Business forecast in 1999 and countermeasures of oil refining industry

    Energy Technology Data Exchange (ETDEWEB)

    On, Kee Woon [Korea Institute for Industrial Economics and Trade, Seoul (Korea)

    1999-02-01

    First of all, the oil refining industry should react wisely to the fluctuation of exchange rate. Therefore, the industry needs to adopt financial methods, such as Hedge or Derivatives, to minimize the risk from the fluctuation of exchange rate. Second, it should speed up advancing financial structure of enterprises considering the active stock market and the decreasing movement of interest rates. Third, it should prepare business fluctuations by continuing the restructuring of enterprises. Lastly, it should react actively to the market opening. With the opening of crude oil market in last year, oil-refining industry in Korea began a full-scale competition with the international major companies. Under these circumstances, it is important to establish a policy not to loose its market to the majors by collaborating with foreign companies or implementing CSM (customer satisfaction management).

  10. Zeolites as Catalysts for Fuels Refining after Indirect Liquefaction Processes

    Directory of Open Access Journals (Sweden)

    Arno de Klerk

    2018-01-01

    Full Text Available The use of zeolite catalysts for the refining of products from methanol synthesis and Fisher–Tropsch synthesis was reviewed. The focus was on fuels refining processes and differences in the application to indirect liquefaction products was compared to petroleum, which is often a case of managing different molecules. Processes covered were skeletal isomerisation of n-butenes, hydroisomerisation of n-butane, aliphatic alkylation, alkene oligomerisation, methanol to hydrocarbons, ethanol and heavier alcohols to hydrocarbons, carbonyls to hydrocarbons, etherification of alkenes with alcohols, light naphtha hydroisomerisation, catalytic naphtha reforming, hydroisomerisation of distillate, hydrocracking and fluid catalytic cracking. The zeolite types that are already industrially used were pointed out, as well as zeolite types that have future promise for specific conversion processes.

  11. Refinement of Bayesian Network Structures upon New Data

    DEFF Research Database (Denmark)

    Zeng, Yifeng; Xiang, Yanping; Pacekajus, Saulius

    2010-01-01

    knowledge and every effort must be made in order to extract it. In this paper, we propose a general merging algorithm to deal with situations when new data have different set of attributes. The merging algorithm updates sufficient statistics when new data are received. It expands the flexibility of BN......Refinement of Bayesian network (BN) structures using new data becomes more and more relevant. Some work has been done there; however, one problem has not been considered yet – what to do when new data have fewer or more attributes than the existing model. In both cases, data contain important...... structure refinement methods. The new algorithm is evaluated in extensive experiments and its applications are discussed at length....

  12. Refinery production planning and scheduling: the refining core business

    Directory of Open Access Journals (Sweden)

    M. Joly

    2012-06-01

    Full Text Available Intelligent production planning and scheduling are of paramount importance to ensure refinery profitability, logistic reliability and safety at the local and corporate levels. In Brazil, such activities play a particularly critical role, since the Brazilian downstream model is moving towards a demand-driven model rather than a supply-driven one. Moreover, new and specialized non-linear constraints are continuously being incorporated into these large-scale problems: increases in oil prices implying the need for processing poor quality crudes, increasing demand and new demand patterns for petroleum products, new stringent environmental regulations related to clean fuels and start-up of new production technologies embedded into more complex refining schemes. This paper aims at clarifying the central role of refinery planning and scheduling activities in the Petrobras refining business. Major past and present results are outlined and corporate long-term strategies to deal with present and future challenges are presented.

  13. Trajectory Optimization Based on Multi-Interval Mesh Refinement Method

    Directory of Open Access Journals (Sweden)

    Ningbo Li

    2017-01-01

    Full Text Available In order to improve the optimization accuracy and convergence rate for trajectory optimization of the air-to-air missile, a multi-interval mesh refinement Radau pseudospectral method was introduced. This method made the mesh endpoints converge to the practical nonsmooth points and decreased the overall collocation points to improve convergence rate and computational efficiency. The trajectory was divided into four phases according to the working time of engine and handover of midcourse and terminal guidance, and then the optimization model was built. The multi-interval mesh refinement Radau pseudospectral method with different collocation points in each mesh interval was used to solve the trajectory optimization model. Moreover, this method was compared with traditional h method. Simulation results show that this method can decrease the dimensionality of nonlinear programming (NLP problem and therefore improve the efficiency of pseudospectral methods for solving trajectory optimization problems.

  14. Financial optimisation and risk management in refining activities

    International Nuclear Information System (INIS)

    Fiorenzani, S.

    2006-01-01

    The real options approach has become a benchmark in real assets evaluation and optimal management problems, especially in liberalised and competitive markets such as the oil and hydrocarbon markets. This paper describes how the same approach can be a useful tool for both risk management decisions and the financial optimisation problem. Refineries are black boxes, which can be used for the transformation of crude oil into more refined hydrocarbon products. These black boxes are characterised by operational flexibilities and constraints, which should be optimally managed in order to maximise the refiner's economic goals. Stochastic dynamic programming represents the right mathematical instrument employed to solve the decision-making problem in such an economic environment. (author)

  15. Former Soviet Union's refining sector faces big shakeout

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    The crisis gripping the refining sector in the former Soviet Union (FSU) is deepening as that industry faces massive rationalization and restructuring. Refinery runs in FSU republics have been on the decline for a number of years. Peak throughput occurred in 1987 at 9.69 million b/d. In Russia, however, the peak came in 1980 at 6.5 million b/d. Given current operable refining capacity in the FSU, now down to about 9.27 million b/d distributed among 48 refineries, capacity utilization will average only about 65% this year. The paper discusses worsening conditions, a comparison of the FSU declines, the financial crisis, energy consumption, and the focus of FSU refineries on secondary capacity to upgrade the product mix

  16. Data Refining for Text Mining Process in Aviation Safety Data

    Science.gov (United States)

    Sjöblom, Olli

    Successful data mining is an iterative process during which data will be refined and adjusted to achieve more accurate mining results. Most important tools in the text mining context are list of stop words and list of synonyms. The size and richness of the lists mentioned depend on the structure of the language used in the text to be mined. English, for example, is an “easy” language for search technologies, because with a couple of exceptions, the stem of the word is not conjugated and terms are formed using several words instead of creating compounds. This requires special attention to definitions when processing morphologically rich languages like Finnish. This chapter introduces the need and realisation of refining the source data for a successful data mining process based onto the results achieved from first mining round.

  17. Production and refining. Increase of Chinese petroleum imports

    International Nuclear Information System (INIS)

    Anon.

    1997-01-01

    China produced 156.5 Mt of petroleum in 1996, from which 56 Mt were extracted from the Daqing oil field, exploited since 1960. About 10% of the crude oil comes from offshore fields. Over the 100 Mt refined in 1996, 20 Mt were imported. The Chinese petroleum products demand should increase to 200 Mt/y by the end of the century with respect to 150 Mt/y in 1997. The Dalian refinery, the first Chinese-foreign joint venture, started to work in November 1996 and should reached its full capacity of 100000 b/day in the first quarter of 1997. The Chinese refining activity has now an excess capacity of 206 Mt/y. Several other joint venture projects in petrochemistry are planned in China. Short paper. (J.S.)

  18. EXPTIME-Completeness of Thorough Refinement on Modal Transition Systems

    DEFF Research Database (Denmark)

    Beneš, Nikola; Křetínský, Jan; Larsen, Kim Guldstrand

    2012-01-01

    -oriented way to decide thorough refinement. If the right-hand side MTS is moreover deterministic, or has a fixed size, the running time of the algorithm becomes polynomial. The lower-bound proof is achieved by reduction from the acceptance problem of alternating linear bounded automata and the problem remains...... EXPTIME-hard even if the left-hand side MTS is fixed and deterministic....

  19. Parallel intergrowths in cronstedtite-1T: Impilcations for structure refinement

    Czech Academy of Sciences Publication Activity Database

    Ďurovič, S.; Hybler, Jiří

    2005-01-01

    Roč. 52, č. 5 (2005), s. 613-621 ISSN 0009-8604 R&D Projects: GA ČR(CZ) GA203/99/0067; GA ČR(CZ) GA202/03/0430 Institutional research plan: CEZ:AV0Z1010914 Keywords : cronstedtite * Fourier syntheses * OD structure * polytype structure refinement * stacking disorder * trioctahedral 1:1 phyllosilicates Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.364, year: 2005

  20. A Generalization of Refined Similarity Hypothesis for Isotropic Turbulence*

    Science.gov (United States)

    Hosokawa, Iwao

    2000-03-01

    The refined similarity hypothesis for isotropic turbulenceestablished by Kolmogorov in 1962 is generalized so that thestatistics of similarity variable may have a slight scale-ratiodependence. A reasonable form of the dependence is given on the basisof a recent multifractal model of intermittent energy dissipation andon some theoretical and experimental knowledge. This modificationleads us to predict reasonable values of all the Kolmogorov prefactorsand the scalings of longitudinal as well as transverse velocitystructure functions in isotropic turbulence.

  1. Off-balance-sheet financing to the refining industry

    International Nuclear Information System (INIS)

    Jenkins, J.H.

    1995-01-01

    Off-balance-sheet lending, or project finance, is becoming an increasingly popular means of capital formation in the refining and petrochemical industries. However, these transactions are substantially different from traditional corporate lending, and the demands placed on the borrower to examine, substantiate, and support the project are far greater. The following paper examines ways in which international banks and other lenders evaluate off-balance-sheet refinery projects and suggests ways to better structure financial representations

  2. Refining borders of genome-rearrangements including repetitions.

    Science.gov (United States)

    Arjona-Medina, J A; Trelles, O

    2016-10-25

    DNA rearrangement events have been widely studied in comparative genomic for many years. The importance of these events resides not only in the study about relatedness among different species, but also to determine the mechanisms behind evolution. Although there are many methods to identify genome-rearrangements (GR), the refinement of their borders has become a huge challenge. Until now no accepted method exists to achieve accurate fine-tuning: i.e. the notion of breakpoint (BP) is still an open issue, and despite repeated regions are vital to understand evolution they are not taken into account in most of the GR detection and refinement methods. We propose a method to refine the borders of GR including repeated regions. Instead of removing these repetitions to facilitate computation, we take advantage of them using a consensus alignment sequence of the repeated region in between two blocks. Using the concept of identity vectors for Synteny Blocks (SB) and repetitions, a Finite State Machine is designed to detect transition points in the difference between such vectors. The method does not force the BP to be a region or a point but depends on the alignment transitions within the SBs and repetitions. The accurate definition of the borders of SB and repeated genomic regions and consequently the detection of BP might help to understand the evolutionary model of species. In this manuscript we present a new proposal for such a refinement. Features of the SBs borders and BPs are different and fit with what is expected. SBs with more diversity in annotations and BPs short and richer in DNA replication and stress response, which are strongly linked with rearrangements.

  3. Refining borders of genome-rearrangements including repetitions

    Directory of Open Access Journals (Sweden)

    JA Arjona-Medina

    2016-10-01

    Full Text Available Abstract Background DNA rearrangement events have been widely studied in comparative genomic for many years. The importance of these events resides not only in the study about relatedness among different species, but also to determine the mechanisms behind evolution. Although there are many methods to identify genome-rearrangements (GR, the refinement of their borders has become a huge challenge. Until now no accepted method exists to achieve accurate fine-tuning: i.e. the notion of breakpoint (BP is still an open issue, and despite repeated regions are vital to understand evolution they are not taken into account in most of the GR detection and refinement methods. Methods and results We propose a method to refine the borders of GR including repeated regions. Instead of removing these repetitions to facilitate computation, we take advantage of them using a consensus alignment sequence of the repeated region in between two blocks. Using the concept of identity vectors for Synteny Blocks (SB and repetitions, a Finite State Machine is designed to detect transition points in the difference between such vectors. The method does not force the BP to be a region or a point but depends on the alignment transitions within the SBs and repetitions. Conclusion The accurate definition of the borders of SB and repeated genomic regions and consequently the detection of BP might help to understand the evolutionary model of species. In this manuscript we present a new proposal for such a refinement. Features of the SBs borders and BPs are different and fit with what is expected. SBs with more diversity in annotations and BPs short and richer in DNA replication and stress response, which are strongly linked with rearrangements.

  4. Nonobtuse local tetrahedral refinements towards a polygonal face/interface

    Czech Academy of Sciences Publication Activity Database

    Korotov, S.; Křížek, Michal

    2011-01-01

    Roč. 24, č. 6 (2011), s. 817-821 ISSN 0893-9659 R&D Projects: GA AV ČR(CZ) IAA100190803 Institutional research plan: CEZ:AV0Z10190503 Keywords : finite element method * nonobtuse tetrahedron * local refinement * discrete maximum principle * boundary and interior layers * interface problem Subject RIV: BA - General Mathematics Impact factor: 1.371, year: 2011 http://www.sciencedirect.com/science/article/pii/S0893965910004726

  5. Grain Refinement of Low Carbon Martensitic Steel by Heat Treatment

    OpenAIRE

    N. V. Kolebina; V. L. Danilov; S. Frechinet

    2015-01-01

    The low-carbon steels have good corrosion and technological properties. Hot deformation is the main operation in manufacturing the parts from these steels. So one of the important properties of the material is a property of plasticity. The grain size significantly influences on the ductility properties of steel. The grain size of steel depends on the chemical composition of the crystallization process, heat treatment, and steel machining. There are plenty methods to have grain refinement. How...

  6. Validating neural-network refinements of nuclear mass models

    Science.gov (United States)

    Utama, R.; Piekarewicz, J.

    2018-01-01

    Background: Nuclear astrophysics centers on the role of nuclear physics in the cosmos. In particular, nuclear masses at the limits of stability are critical in the development of stellar structure and the origin of the elements. Purpose: We aim to test and validate the predictions of recently refined nuclear mass models against the newly published AME2016 compilation. Methods: The basic paradigm underlining the recently refined nuclear mass models is based on existing state-of-the-art models that are subsequently refined through the training of an artificial neural network. Bayesian inference is used to determine the parameters of the neural network so that statistical uncertainties are provided for all model predictions. Results: We observe a significant improvement in the Bayesian neural network (BNN) predictions relative to the corresponding "bare" models when compared to the nearly 50 new masses reported in the AME2016 compilation. Further, AME2016 estimates for the handful of impactful isotopes in the determination of r -process abundances are found to be in fairly good agreement with our theoretical predictions. Indeed, the BNN-improved Duflo-Zuker model predicts a root-mean-square deviation relative to experiment of σrms≃400 keV. Conclusions: Given the excellent performance of the BNN refinement in confronting the recently published AME2016 compilation, we are confident of its critical role in our quest for mass models of the highest quality. Moreover, as uncertainty quantification is at the core of the BNN approach, the improved mass models are in a unique position to identify those nuclei that will have the strongest impact in resolving some of the outstanding questions in nuclear astrophysics.

  7. Project Update: Increased Fuel Affordability through Deployable Refining Technology

    Science.gov (United States)

    2016-08-01

    Form 298 (Rev. 8- 98) Prescribed by ANSI Std. 239.18 1 PROJECT UPDATE: INCREASED FUEL AFFORDABILITY THROUGH DEPLOYABLE REFINING TECHNOLOGY August...Generator fuel ~ 1-2 gph Waste extract ~ 20 gph Feed extractant ~ 20 gph Extraction fluid = denatured ( methanol or DB) ethanol / water 70 / 30...Briefing Charts 3. DATES COVERED (From - To) 15 August 2016 – 30 September 2016 4. TITLE AND SUBTITLE Project Update: Increased Fuel Affordability through

  8. Oil refining and product market developments in Europe

    International Nuclear Information System (INIS)

    McDonald, P.

    1991-01-01

    One political development in Europe that will affect the petroleum refining industry is the opening of a single market among the European Commission countries. Although the single market officially opens on January 1, 1993, a single market for energy will not happen at that time. Most European countries feel that refining is a strategic industry and adopt some form of protectionism in this sector. Environmental policy in Europe tends to be separate from energy policy, making conflicts in setting standards for emissions and fuel composition somewhat inevitable. For example, both environmental and energy policies favor a carbon tax on fuels; the EC environmental commission does not want to be seen as favoring nuclear power, so it favors penalizing all fuels about the same amount, while the energy commission says the carbon tax should be related to the fuel carbon content. A measure affecting the refining industry is the proposal for reducing sulfur in diesel fuel. By 1994 EC countries will have a common 0.2% standard and by 1996 a 0.05% standard for automotive diesel. To meet the latter standard, refineries will need upgrading at an estimated cost of US$4 billion. Another political consideration for the refining industry is whether eastern Europe should be part of the EC energy community. However, if there is a reluctance in the western European countries for a single western market, there is even less enthusiasm for an energy market that includes eastern Europe as well. In addition, there is a reluctance to accept that there should be a free flow of petroleum products from east to west

  9. Dynamic grid refinement for partial differential equations on parallel computers

    International Nuclear Information System (INIS)

    Mccormick, S.; Quinlan, D.

    1989-01-01

    The fast adaptive composite grid method (FAC) is an algorithm that uses various levels of uniform grids to provide adaptive resolution and fast solution of PDEs. An asynchronous version of FAC, called AFAC, that completely eliminates the bottleneck to parallelism is presented. This paper describes the advantage that this algorithm has in adaptive refinement for moving singularities on multiprocessor computers. This work is applicable to the parallel solution of two- and three-dimensional shock tracking problems. 6 refs

  10. Mesh Generation via Local Bisection Refinement of Triangulated Grids

    Science.gov (United States)

    2015-06-01

    Science and Technology Organisation DSTO–TR–3095 ABSTRACT This report provides a comprehensive implementation of an unstructured mesh generation method...and Technology Organisation 506 Lorimer St, Fishermans Bend, Victoria 3207, Australia Telephone: 1300 333 362 Facsimile: (03) 9626 7999 c© Commonwealth...their behaviour is critically linked to Maubach’s method and the data structures N and T . The top- level mesh refinement algorithm is also presented

  11. Creativity: a refinement of the concept for nursing practice.

    Science.gov (United States)

    Fasnacht, Patsy H

    2003-01-01

    This paper seeks to remove some of the ambiguity surrounding the conceptual meaning of creativity using techniques of concept refinement to advance the concept. Creativity is an essential component of nursing practice that occurs daily in nurse's interactions with clients, families and other nurses. Failure to acknowledge and encourage creativity in beginning nurses may hinder future development and innovations in nursing practice and in nursing science. In order to promote the development of creativity it is first necessary to clarify and refine the concept as it applies to nursing. A comprehensive review of a variety of computer and online databases resulted in thousands of articles on creativity between the years 1966 and 1999. The final sample (n = 48) was obtained using both stratified random and purposive sampling techniques. A content analysis of the literature was conducted using methods identified by Morse and illustrated in the work of Hupcey et al. Having determined the concept to be partially mature, the concept was advanced using techniques of concept refinement. Content analysis of the literature yielded three differing definitions for creativity: revelation, birth and reincarnation. Creativity occurs in the presence of intrinsic motivation and a nurturing environment. While value is often used to identify whether a product is creative, the value of the product cannot determine whether the process has occurred. The product produced determines evidence of the process of creativity. Limitations of this investigation are the use of secondary sources and the relatively small sample size (n = 48). Refinement of the concept of creativity indicates that it is a process that may be developed and influenced by the environment and is recognized by the product produced. Further investigation is needed to explore methods and techniques for developing creativity in nursing.

  12. Refinement of nuclear safety education reinforcing technical succession

    International Nuclear Information System (INIS)

    Yokobori, Seiichi

    2008-01-01

    In April 2008, Musashi Institute of Technology established another faculty, the Faculty of Nuclear Safety Engineering, to educate students for nuclear engineering to meet the demands of personnel for nuclear business. At this new faculty, students mainly obtain professional knowledge and skills related to nuclear safety issues. This article described refinement of nuclear safety education by reinforcing technical succession topics, such as Rankine cycle, fission, two-phase flow, defense in depth in safety. LOCA/ECCS, seismic effects, reactor maintenance. (T. Tanaka)

  13. Action Relations. Basic Design Concepts for Behaviour Modelling and Refinement.

    OpenAIRE

    Quartel, Dick

    1998-01-01

    This thesis presents basic design concepts, design methods and a basic design language for distributed system behaviours. This language is based on two basic concepts: the action concept and the causality relation concept. Our methods focus on behaviour refinement, which consists of replacing an abstract behaviour by a more concrete behaviour, such that the concrete behaviour conforms to the abstract behaviour. An important idea underlying this thesis is that an effective design methodology s...

  14. ExpertBayes: Automatically refining manually built Bayesian networks

    OpenAIRE

    Almeida, Ezilda; Ferreira, Pedro; Vinhoza, Tiago; Dutra, Inês; Li, Jingwei; Wu, Yirong; Burnside, Elizabeth

    2014-01-01

    Bayesian network structures are usually built using only the data and starting from an empty network or from a naive Bayes structure. Very often, in some domains, like medicine, a prior structure knowledge is already known. This structure can be automatically or manually refined in search for better performance models. In this work, we take Bayesian networks built by specialists and show that minor perturbations to this original network can yield better classifiers with a very small computati...

  15. Russian refining shows signs of revival, needs investment

    International Nuclear Information System (INIS)

    Plotnikov, V.S.; Avgerinos, G.F.; Dvorets, N.L.; Tyukov, V.M.

    1996-01-01

    The Russian refining industry appears ready for a comeback but needs investment from abroad. After 7 years of annual decline, output of petroleum products in the former Soviet Union (FSU), most of it from Russian refineries, is estimated to have dropped marginally last year. And an increase is possible this year. In 1994, Russia's refineries, which account for two thirds of total FSU distillation capacity, yielded 176.2 million metric tons of oil products, compared with 214.1 million tons in 1993. Despite the precipitous decline in refinery production, net FSU exports oil refined products were down only 5% in 1994 at about 51.3 million tons. This occurred despite the decline in refinery production because of sizable contraction in oil consumption in Russian and the other republics. Russia, like the rest of the FSU, needs more than loans to produce oil or restore wells. According to the Ministries of Economics and Fuels and Energy, 90% of Russian enterprises need foreign capital. Investments to rebuild refining, gas processing, and petrochemicals are necessary, as are funds for modern technologies and equipment. Capital also is needed for extraction of resources that are remotely located or difficult to produce. In addition to providing a legal structure that provides a solid basis for investment, Russian must promote competition, change its tax system to raise revenue but allow companies to retain profits, and remove disincentives to investment for domestic and foreign enterprises

  16. Investment in exploration-production and refining 2014

    International Nuclear Information System (INIS)

    Hureau, Geoffroy; Serbutoviez, Sylvain; Silva, Constancio; Maisonnier, Guy

    2014-11-01

    IFPEN analyses in this study the 2014 evolution of global investment in the field of exploration-production and refining: 1 - Changes in oil and gas prices: General background: weak economy and global disorder, Oil prices: fundamentals that could help to relax oil prices?, Gas prices: fall in Europe, stability in Japan, increase in the US; 2 - Exploration and production - Slowdown in growth: moderate rise in investment in 2014, exploration - Discoveries in 2014, Russia: sanctions will have limited short term impact, implications of the reforms to the Mexican energy sector; 3 - Drilling activity and market throughout the world: onshore and offshore drilling (Number of wells drilled throughout the world, Number of onshore wells, Number of offshore wells, Drilling, equipment and well services markets, Onshore drilling market, Offshore drilling market, Fracking market), Geophysical activity and the geophysical market, Offshore construction activity and the offshore construction market (Offshore construction activities, Rig construction activity, Floating Platform Systems (FPS), Sub-sea constructions, Offshore construction market); 4 - Refining - Significant increase in spending: increase in industrial costs, a slowdown in the increase in excess capacity in the future?, A bleak future for the european refining sector

  17. Marges et perspectives du raffinage Refining Margins and Prospects

    Directory of Open Access Journals (Sweden)

    Baudouin C.

    2006-12-01

    Full Text Available Depuis quelques années le secteur du raffinage est soumis à rude épreuve. La consommation de produits pétroliers augmente peu en Europe, leurs spécifications se durcissent. En raison notamment des progrès permanents dans l'utilisation des unités, les surcapacités de traitement demeurent. . . Tous ces facteurs réunis font que les marges du raffinage à travers le monde restent faibles et insuffisantes pour financer correctement les investissements nouveaux. Refining margins throughout the world have remained low in 1996. In Europe, in spite of an improvement, particularly during the last few weeks, they are still not high enough to finance new investments. Although the demand for petroleum products is increasing, experts are still sceptical about any rapid recovery due to prevailing overcapacity and to continuing capacity growth. After a historical review of margins and an analysis of margins by regions, we analyse refining overcapacities in Europe and the unbalances between production and demand. Then we discuss the current situation concerning barriers to the rationalisation, agreements between oil companies, and the consequences on the future of refining capacities and margins.

  18. Mesh refinement for uncertainty quantification through model reduction

    International Nuclear Information System (INIS)

    Li, Jing; Stinis, Panos

    2015-01-01

    We present a novel way of deciding when and where to refine a mesh in probability space in order to facilitate uncertainty quantification in the presence of discontinuities in random space. A discontinuity in random space makes the application of generalized polynomial chaos expansion techniques prohibitively expensive. The reason is that for discontinuous problems, the expansion converges very slowly. An alternative to using higher terms in the expansion is to divide the random space in smaller elements where a lower degree polynomial is adequate to describe the randomness. In general, the partition of the random space is a dynamic process since some areas of the random space, particularly around the discontinuity, need more refinement than others as time evolves. In the current work we propose a way to decide when and where to refine the random space mesh based on the use of a reduced model. The idea is that a good reduced model can monitor accurately, within a random space element, the cascade of activity to higher degree terms in the chaos expansion. In turn, this facilitates the efficient allocation of computational sources to the areas of random space where they are more needed. For the Kraichnan–Orszag system, the prototypical system to study discontinuities in random space, we present theoretical results which show why the proposed method is sound and numerical results which corroborate the theory

  19. Region-of-interest volumetric visual hull refinement

    KAUST Repository

    Knoblauch, Daniel

    2010-01-01

    This paper introduces a region-of-interest visual hull refinement technique, based on flexible voxel grids for volumetric visual hull reconstructions. Region-of-interest refinement is based on a multipass process, beginning with a focussed visual hull reconstruction, resulting in a first 3D approximation of the target, followed by a region-of-interest estimation, tasked with identifying features of interest, which in turn are used to locally refine the voxel grid and extract a higher-resolution surface representation for those regions. This approach is illustrated for the reconstruction of avatars for use in tele-immersion environments, where head and hand regions are of higher interest. To allow reproducability and direct comparison a publicly available data set for human visual hull reconstruction is used. This paper shows that region-of-interest reconstruction of the target is faster and visually comparable to higher resolution focused visual hull reconstructions. This approach reduces the amount of data generated through the reconstruction, allowing faster post processing, as rendering or networking of the surface voxels. Reconstruction speeds support smooth interactions between the avatar and the virtual environment, while the improved resolution of its facial region and hands creates a higher-degree of immersion and potentially impacts the perception of body language, facial expressions and eye-to-eye contact. Copyright © 2010 by the Association for Computing Machinery, Inc.

  20. Lattice refining loop quantum cosmology, anisotropic models, and stability

    International Nuclear Information System (INIS)

    Bojowald, Martin; Cartin, Daniel; Khanna, Gaurav

    2007-01-01

    A general class of loop quantizations for anisotropic models is introduced and discussed, which enhances loop quantum cosmology by relevant features seen in inhomogeneous situations. The main new effect is an underlying lattice which is being refined during dynamical changes of the volume. In general, this leads to a new feature of dynamical difference equations which may not have constant step-size, posing new mathematical problems. It is discussed how such models can be evaluated and what lattice refinements imply for semiclassical behavior. Two detailed examples illustrate that stability conditions can put strong constraints on suitable refinement models, even in the absence of a fundamental Hamiltonian which defines changes of the underlying lattice. Thus, a large class of consistency tests of loop quantum gravity becomes available. In this context, it will also be seen that quantum corrections due to inverse powers of metric components in a constraint are much larger than they appeared recently in more special treatments of isotropic, free scalar models where they were artificially suppressed

  1. Refining in the 1990's: Restructuring and resurgence

    International Nuclear Information System (INIS)

    Cobb, C.B.

    1994-01-01

    After two years of uncertainty in dealing with the 1990 Clean Air Act Amendments coupled with the shutdown of 5% of total US refining capacity, the industry is now positioning itself for continued operations throughout the remainder of the decade. However, refineries are experiencing a shift in the mode of operations to a period of more restructuring (closings, ventures, alliances, etc.) followed by a resurgence in financial performance. The purpose of this paper is to examine the current industry and highlight the reasons for industry's current plans. The authors also speculate about the strategies companies will choose to better their financial performance. Fundamentally, the characteristics of a mature domestic business remain the driving force that shape decision making. In responding to the maturing of refining, the authors suggest that refiners will change the way they conduct business over the next few years. Building on the theme of the 1993 NPRA paper, strategies will target the domestic side of the business while simultaneously shifting to a global perspective

  2. The state of animal welfare in the context of refinement.

    Science.gov (United States)

    Zurlo, Joanne; Hutchinson, Eric

    2014-01-01

    The ultimate goal of the Three Rs is the full replacement of animals used in biomedical research and testing. However, replacement is unlikely to occur in the near future; therefore the scientific community as a whole must continue to devote considerable effort to ensure optimal animal welfare for the benefit of the science and the animals, i.e., the R of refinement. Laws governing the care and use of laboratory animals have recently been revised in Europe and the US and these place greater emphasis on promoting the well-being of the animals in addition to minimizing pain and distress. Social housing for social species is now the default condition, which can present a challenge in certain experimental settings and for certain species. The practice of positive reinforcement training of laboratory animals, particularly non-human primates, is gathering momentum but is not yet universally employed. Enhanced consideration of refinement extends to rodents, particularly mice, whose use is still increasing as more genetically modified models are generated. The wastage of extraneous mice and the method of their euthanasia are refinement issues that still need to be addressed. An international, concerted effort into defining the needs of laboratory animals is still necessary to improve the quality of the animal models used as well as their welfare.

  3. Superior refining performance beyond 2000 -- Breaking traditional paradigms

    International Nuclear Information System (INIS)

    Tassel, B. van

    1995-01-01

    Over the last 5 years, refining companies have not performed well financially, generating returns below the cost of capital. Environmental regulations have caused the industry to invest significant amounts of capital, and while new regulations will cause the shutdown of between 500 thousand and 1.2 million barrels per day of capacity, the industry structure will remain poor and financial returns for the average player will likely be volatile, cyclical, and below the cost of capital. Based on this industry outlook, refining companies seeking superior performance will have to break the traditional paradigms and adopt world-class practices used in other industries. Changes required to significantly improve financial returns will include shifts in business strategy to accommodate growth, and development of nontraditional services, as well as initiates to dramatically reshape cost structure and improve profitability. Making the changes to become a superior performer in the refining business will require a clear vision and strong leadership at multiple levels in the organization. The transformation will also require changes in company culture and incentive plans that encourage managers to act as owners. In addition, superior performers will push accountability for results to low levels in the organization. Given the herd mentality of the oil industry, superior performers must take decisive, preemptive action to generate a substantial, competitive advantage

  4. Superior refining performance beyond 2000 -- Breaking traditional paradigms

    Energy Technology Data Exchange (ETDEWEB)

    Tassel, B. van [McKinsey and Co., Inc., Houston, TX (United States)

    1995-09-01

    Over the last 5 years, refining companies have not performed well financially, generating returns below the cost of capital. Environmental regulations have caused the industry to invest significant amounts of capital, and while new regulations will cause the shutdown of between 500 thousand and 1.2 million barrels per day of capacity, the industry structure will remain poor and financial returns for the average player will likely be volatile, cyclical, and below the cost of capital. Based on this industry outlook, refining companies seeking superior performance will have to break the traditional paradigms and adopt world-class practices used in other industries. Changes required to significantly improve financial returns will include shifts in business strategy to accommodate growth, and development of nontraditional services, as well as initiates to dramatically reshape cost structure and improve profitability. Making the changes to become a superior performer in the refining business will require a clear vision and strong leadership at multiple levels in the organization. The transformation will also require changes in company culture and incentive plans that encourage managers to act as owners. In addition, superior performers will push accountability for results to low levels in the organization. Given the herd mentality of the oil industry, superior performers must take decisive, preemptive action to generate a substantial, competitive advantage.

  5. CONSTRAINED-TRANSPORT MAGNETOHYDRODYNAMICS WITH ADAPTIVE MESH REFINEMENT IN CHARM

    International Nuclear Information System (INIS)

    Miniati, Francesco; Martin, Daniel F.

    2011-01-01

    We present the implementation of a three-dimensional, second-order accurate Godunov-type algorithm for magnetohydrodynamics (MHD) in the adaptive-mesh-refinement (AMR) cosmological code CHARM. The algorithm is based on the full 12-solve spatially unsplit corner-transport-upwind (CTU) scheme. The fluid quantities are cell-centered and are updated using the piecewise-parabolic method (PPM), while the magnetic field variables are face-centered and are evolved through application of the Stokes theorem on cell edges via a constrained-transport (CT) method. The so-called multidimensional MHD source terms required in the predictor step for high-order accuracy are applied in a simplified form which reduces their complexity in three dimensions without loss of accuracy or robustness. The algorithm is implemented on an AMR framework which requires specific synchronization steps across refinement levels. These include face-centered restriction and prolongation operations and a reflux-curl operation, which maintains a solenoidal magnetic field across refinement boundaries. The code is tested against a large suite of test problems, including convergence tests in smooth flows, shock-tube tests, classical two- and three-dimensional MHD tests, a three-dimensional shock-cloud interaction problem, and the formation of a cluster of galaxies in a fully cosmological context. The magnetic field divergence is shown to remain negligible throughout.

  6. The petroleum refining industry and the implications for the environment

    International Nuclear Information System (INIS)

    Saraiva, Gerardo Jose de Pontes

    2000-01-01

    The petroleum refining industry is basically concerned with the production of oil, lubricants and intermediate petrochemical products, utilizing crude oil as its main raw material. Petroleum refining, a distillation process that breaks hydrocarbons into fractions, eliminating undesired impurities, generates irreducible residues. Until the industrial revolution, the residues were essentially organic, susceptible to the attack of agents of destruction and transformation (bacterium, fungi, etc). Suddenly, due to the intensification of human activities of modern man, nature scattered across the planet more resistant products, many of them with long life times, that produce a deeper impact in the environment. Almost entirely marine is the pollution that results from increasing quantity of hydrocarbons dumped into the sea, a problem that is aggravated by the development of manufacturing and transportation of petroleum products. The expansion of the petroleum commerce, using essentially maritime transportation, has increased considerably the probability of accidents increasing the risks of environment pollution. This work presents suggestions and possible solutions to minimize the problem of environment pollution, caused by refining and transportation of this combustible, essential to present time industry. (author)

  7. Morse Set Classification and Hierarchical Refinement Using Conley Index

    KAUST Repository

    Guoning Chen,

    2012-05-01

    Morse decomposition provides a numerically stable topological representation of vector fields that is crucial for their rigorous interpretation. However, Morse decomposition is not unique, and its granularity directly impacts its computational cost. In this paper, we propose an automatic refinement scheme to construct the Morse Connection Graph (MCG) of a given vector field in a hierarchical fashion. Our framework allows a Morse set to be refined through a local update of the flow combinatorialization graph, as well as the connection regions between Morse sets. The computation is fast because the most expensive computation is concentrated on a small portion of the domain. Furthermore, the present work allows the generation of a topologically consistent hierarchy of MCGs, which cannot be obtained using a global method. The classification of the extracted Morse sets is a crucial step for the construction of the MCG, for which the Poincar index is inadequate. We make use of an upper bound for the Conley index, provided by the Betti numbers of an index pair for a translation along the flow, to classify the Morse sets. This upper bound is sufficiently accurate for Morse set classification and provides supportive information for the automatic refinement process. An improved visualization technique for MCG is developed to incorporate the Conley indices. Finally, we apply the proposed techniques to a number of synthetic and real-world simulation data to demonstrate their utility. © 2006 IEEE.

  8. Advanced breeder cycle uses metallic fuel

    International Nuclear Information System (INIS)

    Chang, Y.I.

    1991-01-01

    Scientists from Argonne National Laboratory have been developing a concept called the Integral fast Reactor (IFR). This fast breeder reactor could effectively increase Uranium resources a hundred fold making nuclear power essentially an inexhaustible energy source. The IFR is outlined. In the IFR, the inherent properties of liquid metal cooling are combined with a new metallic fuel which is allowed to swell and gives an improved burnup level and a radically different refining process to allow breakthroughs in passive safety, fuel cycle economics and waste management. (author)

  9. Heavy metal

    African Journals Online (AJOL)

    of spawning, resistance to diseases and social acceptability (Pillay, 1993). This study aimed at determining the carbohydrate reserves and heavy metal accumulation of the Nile tilapia, Oreochromis miloticus after treatment with heavy metals such as lead, copper and zinc. 2. Materials and Methods. Test organism: Nile tilapia ...

  10. Plasma metallization

    International Nuclear Information System (INIS)

    Crowther, J.M.

    1997-09-01

    Many methods are currently used for the production of thin metal films. However, all of these have drawbacks associated with them, for example the need for UHV conditions, high temperatures, exotic metal precursors, or the inability to coat complex shaped objects. Reduction of supported metal salts by non-isothermal plasma treatment does not suffer from these drawbacks. In order to produce and analyse metal films before they become contaminated, a plasma chamber which could be attached directly to a UHV chamber with XPS capability was designed and built. This allowed plasma treatment of supported metal salts and surface analysis by XPS to be performed without exposure of the metal film to the atmosphere. Non-equilibrium plasma treatment of Nylon 66 supported gold(lll) chloride using hydrogen as the feed gas resulted in a 95% pure gold film, the remaining 5% of the film being carbon. If argon or helium were used as the feed gases during plasma treatment the resultant gold films were 100% pure. Some degree of surface contamination of the films due to plasma treatment was observed but was easily removed by argon ion cleaning. Hydrogen plasma reduction of glass supported silver(l) nitrate and palladium(ll) acetate films reveals that this metallization technique is applicable to a wide variety of metal salts and supports, and has also shown the ability of plasma reduction to retain the complex 'fern-like' structures seen for spin coated silver(l) nitrate layers. Some metal salts are susceptible to decomposition by X-rays. The reduction of Nylon 66 supported gold(lll) chloride films by soft X-rays to produce nanoscopic gold particles has been studied. The spontaneous reduction of these X-ray irradiated support gold(lll) chloride films on exposure to the atmosphere to produce gold rich metallic films has also been reported. (author)

  11. Melting-decontamination method for radioactive contaminated metals

    International Nuclear Information System (INIS)

    Uda, Tatsuhiko; Tsuchiya, Hiroyuki; Miura, Noboru; Iba, Hajime.

    1985-01-01

    Purpose: To eliminate uranium components remaining in metals even after the uranium-contaminated metals are melted. Method: Metal wastes contaminated with actinide element or its compound as nuclear fuel substance are melted in a crucible. Molten metals are fallen through a filter disposed at the bottom of the crucible into another receiving crucible. Uranium compounds are still left in the molten metal fallen in the receiving crucible. The residual uranium compounds are concentrated by utilizing the principle of the zone-refining process. That is, a displaceable local-heating heater is disposed to the receiving crucible, by which metals once solidified in the receiving crucible is again heated locally to transfer from solid to molten phase in a quasi-equibilized manner. In this way, by eliminating the end of the metal rod at which the uranium is segregated, the contaminating coefficient can be improved. (Ikeda, J.)

  12. Refined Modeling of Flexural Deformation of Layered Plates with a Regular Structure Made from Nonlinear Hereditary Materials

    Science.gov (United States)

    Yankovskii, A. P.

    2018-01-01

    On the basis of constitutive equations of the Rabotnov nonlinear hereditary theory of creep, the problem on the rheonomic flexural behavior of layered plates with a regular structure is formu-lated. Equations allowing one to describe, with different degrees of accuracy, the stress-strain state of such plates with account of their weakened resistance to transverse shear were ob-tained. From them, the relations of the nonclassical Reissner- and Reddytype theories can be found. For axially loaded annular plates clamped at one edge and loaded quasistatically on the other edge, a simplified version of the refined theory, whose complexity is comparable to that of the Reissner and Reddy theories, is developed. The flexural strains of such metal-composite annular plates in shortterm and long-term loadings at different levels of heat action are calcu-lated. It is shown that, for plates with a relative thickness of order of 1/10, neither the classical theory, nor the traditional nonclassical Reissner and Reddy theories guarantee reliable results for deflections even with the rough 10% accuracy. The accuracy of these theories decreases at elevated temperatures and with time under long-term loadings of structures. On the basic of relations of the refined theory, it is revealed that, in bending of layered metal-composite heat-sensitive plates under elevated temperatures, marked edge effects arise in the neighborhood of the supported edge, which characterize the shear of these structures in the transverse direction

  13. RETRACTED ARTICLE: Comparison on grain refinement efficiency of peritectic and eutectic alloying elements on pure aluminium

    Science.gov (United States)

    Haghayeghi, R.; Kapranos, P.

    2014-07-01

    The work investigated the grain refining efficiency of peritectic forming solutes as well as eutectic solutes on pure Al. Significant grain refinement for peritectic and small refinement for the eutectic elements were achieved and the mechanisms of refinement were studied. In order to investigate the grain structure and solidification phenomena for each set of alloys, a TP-1 test, as well as thermal analysis, was performed and back scattered images were used to analyze the phases that may contribute to the grain refinement. It appears that the significant grain refinement of peritectic elements is due to the formation of in-situ properitectic particles and their appropriate constitutional undercooling. The results suggest that the availability of potent nuclei and exogenous particles play major roles in the grain refinement efficiency. However, in the case of eutectic elements only segregation power contributes to refinement whilst the availability of potent nuclei is of paramount importance.

  14. Direct reduction of uranium dioxide and few other metal oxides to corresponding metals by high temperature molten salt electrolysis

    International Nuclear Information System (INIS)

    Mohandas, K.S.

    2017-01-01

    Molten salt based electro-reduction processes, capable of directly converting solid metal oxides to metals with minimum intermediate steps, are being studied worldwide. Production of metals apart, the process assumes importance in nuclear technology in the context of pyrochemical reprocessing of spent oxide fuels, for it serves as an intermediate step to convert spent oxide fuel to a metal alloy, which in turn can be processed by molten salt electro-refining method to gain the actinides present in it. In the context of future metal fuel fast reactor programme, the electrochemical process was studied for conversion of solid UO 2 to U metal in LiCl-1wt.% Li 2 O melt at 650 °C with platinum anode at the Metal Processing Studies Section, PMPD, IGCAR. A brief overview of the work is presented in the paper

  15. Obtainment of lithium metal by electrolysis of molten salts

    International Nuclear Information System (INIS)

    Silva Costa, M.A.Z. da.

    1988-04-01

    The obtainment metallic lithium through KCL + LiCl, using a stainless steel cathode and a graphite anode is studied. The applications of lithium on nuclear energy, aerospatial program, metalurgy and as refining and degassing agent are also presented. The purification of lithium is still mentioned. (C.G.C.) [pt

  16. Life Cycle Assessment of Metals: A Scientific Synthesis

    Science.gov (United States)

    Nuss, Philip; Eckelman, Matthew J.

    2014-01-01

    We have assembled extensive information on the cradle-to-gate environmental burdens of 63 metals in their major use forms, and illustrated the interconnectedness of metal production systems. Related cumulative energy use, global warming potential, human health implications and ecosystem damage are estimated by metal life cycle stage (i.e., mining, purification, and refining). For some elements, these are the first life cycle estimates of environmental impacts reported in the literature. We show that, if compared on a per kilogram basis, the platinum group metals and gold display the highest environmental burdens, while many of the major industrial metals (e.g., iron, manganese, titanium) are found at the lower end of the environmental impacts scale. If compared on the basis of their global annual production in 2008, iron and aluminum display the largest impacts, and thallium and tellurium the lowest. With the exception of a few metals, environmental impacts of the majority of elements are dominated by the purification and refining stages in which metals are transformed from a concentrate into their metallic form. Out of the 63 metals investigated, 42 metals are obtained as co-products in multi output processes. We test the sensitivity of varying allocation rationales, in which the environmental burden are allocated to the various metal and mineral products, on the overall results. Monte-Carlo simulation is applied to further investigate the stability of our results. This analysis is the most comprehensive life cycle comparison of metals to date and allows for the first time a complete bottom-up estimate of life cycle impacts of the metals and mining sector globally. We estimate global direct and indirect greenhouse gas emissions in 2008 at 3.4 Gt CO2-eq per year and primary energy use at 49 EJ per year (9.5% of global use), and report the shares for all metals to both impact categories. PMID:24999810

  17. Life cycle assessment of metals: a scientific synthesis.

    Directory of Open Access Journals (Sweden)

    Philip Nuss

    Full Text Available We have assembled extensive information on the cradle-to-gate environmental burdens of 63 metals in their major use forms, and illustrated the interconnectedness of metal production systems. Related cumulative energy use, global warming potential, human health implications and ecosystem damage are estimated by metal life cycle stage (i.e., mining, purification, and refining. For some elements, these are the first life cycle estimates of environmental impacts reported in the literature. We show that, if compared on a per kilogram basis, the platinum group metals and gold display the highest environmental burdens, while many of the major industrial metals (e.g., iron, manganese, titanium are found at the lower end of the environmental impacts scale. If compared on the basis of their global annual production in 2008, iron and aluminum display the largest impacts, and thallium and tellurium the lowest. With the exception of a few metals, environmental impacts of the majority of elements are dominated by the purification and refining stages in which metals are transformed from a concentrate into their metallic form. Out of the 63 metals investigated, 42 metals are obtained as co-products in multi output processes. We test the sensitivity of varying allocation rationales, in which the environmental burden are allocated to the various metal and mineral products, on the overall results. Monte-Carlo simulation is applied to further investigate the stability of our results. This analysis is the most comprehensive life cycle comparison of metals to date and allows for the first time a complete bottom-up estimate of life cycle impacts of the metals and mining sector globally. We estimate global direct and indirect greenhouse gas emissions in 2008 at 3.4 Gt CO2-eq per year and primary energy use at 49 EJ per year (9.5% of global use, and report the shares for all metals to both impact categories.

  18. A deformation mechanism of hard metal surrounded by soft metal during roll forming

    Science.gov (United States)

    Yu, Hailiang; Tieu, A. Kiet; Lu, Cheng; Liu, Xiong; Godbole, Ajit; Li, Huijun; Kong, Charlie; Qin, Qinghua

    2014-05-01

    It is interesting to imagine what would happen when a mixture of soft-boiled eggs and stones is deformed together. A foil made of pure Ti is stronger than that made of Cu. When a composite Cu/Ti foil deforms, the harder Ti will penetrate into the softer Cu in the convex shapes according to previously reported results. In this paper, we describe the fabrication of multilayer Cu/Ti foils by the roll bonding technique and report our observations. The experimental results lead us to propose a new deformation mechanism for a hard metal surrounded by a soft metal during rolling of a laminated foil, particularly when the thickness of hard metal foil (Ti, 25 μm) is much less than that of the soft metal foil (Cu, 300 μm). Transmission Electron Microscope (TEM) imaging results show that the hard metal penetrates into the soft metal in the form of concave protrusions. Finite element simulations of the rolling process of a Cu/Ti/Cu composite foil are described. Finally, we focus on an analysis of the deformation mechanism of Ti foils and its effects on grain refinement, and propose a grain refinement mechanism from the inside to the outside of the laminates during rolling.

  19. Machining-induced deformation in stepped specimens of PH 13-8 Mo, 18 nickel maraging steel grade 200T1 and grain-refined HP 9-4-20

    Science.gov (United States)

    Wigley, D. A.

    1985-01-01

    The results of a study to evaluate the dimensional changes created during machining and subsequent cycling to cryogenic temperatures for three different metallic alloys are presented. Experimental techniques are described and results presented for 18 Ni Grade 200 maraging steel, PH-13-8 Mo stainless steel, and Grain-refined HP 9-4-20.

  20. Assessing food allergy risks from residual peanut protein in highly refined vegetable oil

    NARCIS (Netherlands)

    Blom, W.M.; Kruizinga, A.G.; Rubingh, C.M.; Remington, B.C.; Crevel, R.W.R.; Houben, G.F.

    2017-01-01

    Refined vegetable oils including refined peanut oil are widely used in foods. Due to shared production processes, refined non-peanut vegetable oils can contain residual peanut proteins. We estimated the predicted number of allergic reactions to residual peanut proteins using probabilistic risk

  1. 40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

    Science.gov (United States)

    2010-07-01

    ... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL... Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar... processing of raw cane sugar into crystalline refined sugar. ...

  2. Gross wood characteristics affecting properties of handsheets made from loblolly pine refiner groundwood

    Science.gov (United States)

    Charles W. McMillin

    1968-01-01

    Specific refining energy and gross wood properties accounted for as much as 90% of the total variation in strength of handsheets made from 96 pulps disk-refined from chips of varying characteristics. Burst, tear, and breaking length were increased by applying high specific refining energy and using fast-grown wood of high latewood content but of relatively low density...

  3. Refinement-Animation for Event-B - Towards a Method of Validation

    DEFF Research Database (Denmark)

    Hallerstede, Stefan; Leuschel, Michael; Plagge, Daniel

    2010-01-01

    We provide a detailed description of refinement in Event-B, both as a contribution in itself and as a foundation for the approach to simultaneous animation of multiple levels of refinement that we propose. We present an algorithm for simultaneous multi-level animation of refinement, and show how ...

  4. 76 FR 61472 - Revised Fiscal Year 2011 Tariff-Rate Quota Allocations for Refined Sugar

    Science.gov (United States)

    2011-10-04

    ... TRADE REPRESENTATIVE Revised Fiscal Year 2011 Tariff-Rate Quota Allocations for Refined Sugar AGENCY... the fiscal year (FY) 2011 in-quota quantity of the tariff-rate quota (TRQ) for imported refined sugar... imports of refined sugar. Section 404(d)(3) of the Uruguay Round Agreements Act (19 U.S.C. 3601(d)(3...

  5. 77 FR 52021 - Proposed CERCLA Administrative Settlement Agreement and Order on Consent for the Mercury Refining...

    Science.gov (United States)

    2012-08-28

    ... and Order on Consent for the Mercury Refining Superfund Site, Towns of Guilderland and Colonie, Albany... Management of Michigan, Inc. (hereafter ``Settling Parties'') pertaining to the Mercury Refining Superfund... Superfund Mercury Refining Superfund Site Special Account, which combined total $79,028.49. Each Settling...

  6. A refined index of model performance: a rejoinder

    Science.gov (United States)

    Legates, David R.; McCabe, Gregory J.

    2013-01-01

    Willmott et al. [Willmott CJ, Robeson SM, Matsuura K. 2012. A refined index of model performance. International Journal of Climatology, forthcoming. DOI:10.1002/joc.2419.] recently suggest a refined index of model performance (dr) that they purport to be superior to other methods. Their refined index ranges from − 1.0 to 1.0 to resemble a correlation coefficient, but it is merely a linear rescaling of our modified coefficient of efficiency (E1) over the positive portion of the domain of dr. We disagree with Willmott et al. (2012) that dr provides a better interpretation; rather, E1 is more easily interpreted such that a value of E1 = 1.0 indicates a perfect model (no errors) while E1 = 0.0 indicates a model that is no better than the baseline comparison (usually the observed mean). Negative values of E1 (and, for that matter, dr McCabe [Legates DR, McCabe GJ. 1999. Evaluating the use of “goodness-of-fit” measures in hydrologic and hydroclimatic model validation. Water Resources Research 35(1): 233-241.] and Schaefli and Gupta [Schaefli B, Gupta HV. 2007. Do Nash values have value? Hydrological Processes 21: 2075-2080. DOI: 10.1002/hyp.6825.]. This important discussion focuses on the appropriate baseline comparison to use, and why the observed mean often may be an inadequate choice for model evaluation and development. 

  7. Risk as economic category: systematics scientific approach and refinement contents

    Directory of Open Access Journals (Sweden)

    V.G. Vygovskyy

    2015-03-01

    Full Text Available The paper studies the categorical-conceptual apparatus of risk and its refinement based on a critical analysis of existing systematic scientific approaches. Determined that in the refinement of the economic nature of the risk of a number of controversial issues: the definition of the objective or subjective nature of risk; matching of concepts such as «risk», «danger», «loss», «probability of loss»; definition of negative or positive consequences of risk; identification of risk with its consequences, or source of origin, which makes the relevance of research topics. As a result of scientific research has been refined interpretation of risk as an economic category, the characteristics of the company associated with the probability of unforeseen situations that may lead to negative and positive impacts, assessment of which requires the development of alternatives for management decisions. Clarification of the definition focuses on the possibility (probability of a favorable (unfavorable events which require certain corrective action management unit of the enterprise. The author emphasizes the mandatory features of the category of «risk», in particular: the concept of risk is always associated with the uncertainty of the future; event occurring has implications for the enterprise (both negative and positive; consequences for necessitates the development of a number of alternative solutions to the possible elimination of the negative consequences of risky events; risk – a mandatory attribute of modern management (its value is enhanced in terms of market conditions; subject to risk assessment and management by the company. Dedicated and updated features contribute to the clarification of the nature of the economic risk and categorical conceptual apparatus of risk management.

  8. Prediction of acute toxicity of cadmium and lead to zebrafish larvae by using a refined toxicokinetic-toxicodynamic model

    International Nuclear Information System (INIS)

    Gao, Yongfei; Feng, Jianfeng; Zhu, Lin

    2015-01-01

    Highlights: • We developed a BLM-aided TK-TD model that considers the effects of H + . • The time-course metal concentration in larvae was well described by the TK model. • The time-course survival of zebrafish larvae was well simulated by the TD model. - Abstract: The biotic ligand model (BLM) and the toxicokinetic-toxicodynamic (TK-TD) model are essential in predicting the acute toxicity of metals in various species and exposure conditions; however, these models are usually separately utilized. In this study, a mechanistic TK-TD model was developed to predict the acute toxicity of 10 −6 M Cd and 10 −6 M Pb to zebrafish (Danio rerio) larvae. The novel approach links the BLM with relevant TK processes to simulate the bioaccumulation processes of Cd or Pb as a function of the maximum uptake rate of each metal, the affinity constants, and the concentrations of free metal ions and H + in test solutions. Results showed that the refined TK-TD model can accurately predict the accumulation and acute toxicity of Cd and Pb to zebrafish larvae at pH 5.5, 6.5, and 7.0.

  9. Prediction of acute toxicity of cadmium and lead to zebrafish larvae by using a refined toxicokinetic-toxicodynamic model

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Yongfei; Feng, Jianfeng, E-mail: fengjf@nankai.edu.cn; Zhu, Lin, E-mail: zhulin@nankai.edu.cn

    2015-12-15

    Highlights: • We developed a BLM-aided TK-TD model that considers the effects of H{sup +}. • The time-course metal concentration in larvae was well described by the TK model. • The time-course survival of zebrafish larvae was well simulated by the TD model. - Abstract: The biotic ligand model (BLM) and the toxicokinetic-toxicodynamic (TK-TD) model are essential in predicting the acute toxicity of metals in various species and exposure conditions; however, these models are usually separately utilized. In this study, a mechanistic TK-TD model was developed to predict the acute toxicity of 10{sup −6} M Cd and 10{sup −6} M Pb to zebrafish (Danio rerio) larvae. The novel approach links the BLM with relevant TK processes to simulate the bioaccumulation processes of Cd or Pb as a function of the maximum uptake rate of each metal, the affinity constants, and the concentrations of free metal ions and H{sup +} in test solutions. Results showed that the refined TK-TD model can accurately predict the accumulation and acute toxicity of Cd and Pb to zebrafish larvae at pH 5.5, 6.5, and 7.0.

  10. Metals 2000

    Energy Technology Data Exchange (ETDEWEB)

    Allison, S.W.; Rogers, L.C.; Slaughter, G. [Oak Ridge National Lab., TN (United States); Boensch, F.D. [6025 Oak Hill Lane, Centerville, OH (United States); Claus, R.O.; de Vries, M. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States)

    1993-05-01

    This strategic planning exercise identified and characterized new and emerging advanced metallic technologies in the context of the drastic changes in global politics and decreasing fiscal resources. In consideration of a hierarchy of technology thrusts stated by various Department of Defense (DOD) spokesmen, and the need to find new and creative ways to acquire and organize programs within an evolving Wright Laboratory, five major candidate programs identified are: C-17 Flap, Transport Fuselage, Mach 5 Aircraft, 4.Fighter Structures, and 5. Missile Structures. These results were formed by extensive discussion with selected major contractors and other experts, and a survey of advanced metallic structure materials. Candidate structural applications with detailed metal structure descriptions bracket a wide variety of uses which warrant consideration for the suggested programs. An analysis on implementing smart skins and structures concepts is given from a metal structures perspective.

  11. Refined life-cycle assessment of polymer solar cells

    DEFF Research Database (Denmark)

    Lenzmann, F.; Kroon, J.; Andriessen, R.

    2011-01-01

    A refined life-cycle assessment of polymer solar cells is presented with a focus on critical components, i.e. the transparent conductive ITO layer and the encapsulation components. This present analysis gives a comprehensive sketch of the full environmental potential of polymer-OPV in comparison...... with other PV technologies. It is shown that on a m2 basis the environmental characteristics of polymer-OPV are highly beneficial, while on a watt-peak and on a kWh basis, these benefits are - at the current level of the development - still (over-)compensated by low module efficiency and limited lifetime...

  12. Cogeneration handbook for the petroleum refining industry. [Contains glossary

    Energy Technology Data Exchange (ETDEWEB)

    Fassbender, L.L.; Garrett-Price, B.A.; Moore, N.L.; Fassbender, A.G.; Eakin, D.E.; Gorges, H.A.

    1984-03-01

    The decision of whether to cogenerate involves several considerations, including technical, economic, environmental, legal, and regulatory issues. Each of these issues is addressed separately in this handbook. In addition, a chapter is included on preparing a three-phase work statement, which is needed to guide the design of a cogeneration system. In addition, an annotated bibliography and a glossary of terminology are provided. Appendix A provides an energy-use profile of the petroleum refining industry. Appendices B through O provide specific information that will be called out in subsequent chapters.

  13. Evolving a puncture black hole with fixed mesh refinement

    International Nuclear Information System (INIS)

    Imbiriba, Breno; Baker, John; Centrella, Joan; Meter, James R. van; Choi, Dae-Il; Fiske, David R.; Brown, J. David; Olson, Kevin

    2004-01-01

    We present an algorithm for treating mesh refinement interfaces in numerical relativity. We discuss the behavior of the solution near such interfaces located in the strong-field regions of dynamical black hole spacetimes, with particular attention to the convergence properties of the simulations. In our applications of this technique to the evolution of puncture initial data with vanishing shift, we demonstrate that it is possible to simultaneously maintain second order convergence near the puncture and extend the outer boundary beyond 100M, thereby approaching the asymptotically flat region in which boundary condition problems are less difficult and wave extraction is meaningful

  14. Colombia defines innovative plans for refining and petrochemicals

    International Nuclear Information System (INIS)

    Carta Petrolera

    1998-01-01

    Ecopetrol plans to increase capacity at its Cartagena refinery to 140,000 barrels per day until 2002. The new production will be for basic streams to supply and stimulate new industries in the petrochemical sector. Investment has concentrated on exploration and production and far less on the rest of the oil sector, but now Ecopetrol will be new financing plans to develop refining in keeping with government guidelines. The Ecopetrol Board approved the development plan for the Cartagena Refinery, this consist of increasing capacity

  15. Panorama 2011: Water in fuel production Oil production and refining

    International Nuclear Information System (INIS)

    Nabzar, L.

    2011-01-01

    Water plays a vital role in the production of fuels. Against a background of extremely high pressure to do with the need to protect the environment, better manage energy use and operate in a socially responsible manner - as well as the need to protect water as a resource and reduce greenhouse gas emissions, water management has become a major issue for the oil industry. These issues have all more or less been factored into the integrated water management programmes which have been introduced both in oil production and oil refining. These programmes have been designed to keep waste and emissions to a minimum, and to reduce the quantities of water required. (author)

  16. Shadowing of physical trajectories in chaotic dynamics: Containment and refinement

    International Nuclear Information System (INIS)

    Grebogi, C.; Hammel, S.M.; Yorke, J.A.; Sauer, T.

    1990-01-01

    For a chaotic system, a noisy trajectory diverges rapidly from the true trajectory with the same initial condition. To understand in what sense the noisy trajectory reflects the true dynamics of the actual system, we developed a rigorous procedure to show that some true trajectories remain close to the noisy one for long times. The procedure involves a combination of containment, which establishes the existence of an uncountable number of true trajectories close to the noisy one, and refinement, which produces a less noisy trajectory. Our procedure is applied to noisy chaotic trajectories of the standard map and the driven pendulum

  17. Minimally refined biomass fuel. [carbohydrate-water-alcohol mixture

    Energy Technology Data Exchange (ETDEWEB)

    Pearson, R.K.; Hirschfeld, T.B.

    1981-03-26

    A minimally refined fluid composition, suitable as a fuel mixture and derived from biomass material, is comprised of one or more water-soluble carbohydrates such as sucrose, one or more alcohols having less than four carbons, and water. The carbohydrate provides the fuel source; water-solubilizes the carbohydrate; and the alcohol aids in the combustion of the carbohydrate and reduces the viscosity of the carbohydrate/water solution. Because less energy is required to obtain the carbohydrate from the raw biomass than alcohol, an overall energy savings is realized compared to fuels employing alcohol as the primary fuel.

  18. Refinement of Representation Theorems for Context-Free Languages

    Science.gov (United States)

    Fujioka, Kaoru

    In this paper, we obtain some refinement of representation theorems for context-free languages by using Dyck languages, insertion systems, strictly locally testable languages, and morphisms. For instance, we improved the Chomsky-Schützenberger representation theorem and show that each context-free language L can be represented in the form L = h (D ∩ R), where D is a Dyck language, R is a strictly 3-testable language, and h is a morphism. A similar representation for context-free languages can be obtained, using insertion systems of weight (3, 0) and strictly 4-testable languages.

  19. Recycling and refining of copper for electrical application

    Directory of Open Access Journals (Sweden)

    Dablement Sébastien

    2013-11-01

    Full Text Available Copper is, after silver, the best electrical conductor. All residual impurities inside the matrix have high consequences on these properties. Thus, the Nexans factory in Lens “purifies” the copper scraps by a fire refining in order to remove all the internal pollutant. This process, unique in France, is complementary to a traditional process using an electrolytic cathode. It allows, first, to diversify the raw material and, second, to increase the ecological balance compare to the traditional way of scrap treatment for electrical application.

  20. Refining image segmentation by integration of edge and region data

    Science.gov (United States)

    Le Moigne, Jacqueline; Tilton, James C.

    1992-01-01

    An iterative parallel region growing (IPRG) algorithm previously developed by Tilton (1989) produces hierarchical segmentations of images from finer to coarser resolution. An ideal segmentation does not always correspond to one single iteration but to several different ones, each one producing the 'best' result for a separate part of the image. With the goal of finding this ideal segmentation, the results of the IPRG algorithm are refined by utilizing some additional information, such as edge features, and by interpreting the tree of hierarchical regions.

  1. ExpertBayes: Automatically refining manually built Bayesian networks.

    Science.gov (United States)

    Almeida, Ezilda; Ferreira, Pedro; Vinhoza, Tiago; Dutra, Inês; Li, Jingwei; Wu, Yirong; Burnside, Elizabeth

    2014-12-01

    Bayesian network structures are usually built using only the data and starting from an empty network or from a naïve Bayes structure. Very often, in some domains, like medicine, a prior structure knowledge is already known. This structure can be automatically or manually refined in search for better performance models. In this work, we take Bayesian networks built by specialists and show that minor perturbations to this original network can yield better classifiers with a very small computational cost, while maintaining most of the intended meaning of the original model.

  2. Comprehensive adaptive mesh refinement in wrinkling prediction analysis

    NARCIS (Netherlands)

    Selman, A.; Meinders, Vincent T.; Huetink, Han; van den Boogaard, Antonius H.

    2002-01-01

    Discretisation errors indicator, contact free wrinkling and wrinkling with contact indicators are, in a challenging task, brought together and used in a comprehensive approach to wrinkling prediction analysis in thin sheet metal forming processes.

  3. Metal carbides

    International Nuclear Information System (INIS)

    Wells, A.F.

    1988-01-01

    From the viewpoint of general crystal chemistry principles and on the base of modern data the structural chemistry of metal carbides is presented. The classification deviding metal carbides into 4 groups depending on chemical and physical properties is presented. The features of the crystal structure of carbides of alkali alkaline earth, transition, 4 f- and 5f-elements and their effect on physical and chemical properties are considered

  4. Development of an efficient grain refiner for Al-7Si alloy

    Energy Technology Data Exchange (ETDEWEB)

    Kori, S.A.; Murty, B.S.; Chakraborty, M. [Indian Inst. of Technol., Kharagpur (India). Dept. of Metall. and Mater. Eng.

    2000-03-15

    The response of Al-7Si alloy towards grain refinement by Al-Ti-B master alloys (with different Ti-B ratios) at different addition levels has been studied in detail. The results indicate that high B-containing master alloys are powerful grain refiners when compared to conventional grain refiners like Al-5Ti-lB master alloys. In the present study, indigenously developed master alloys have been used for the grain refinement of alloys Al-7Si and LM-25. Significant improvements in mechanical properties have been obtained with a combination of grain refiner and Sr as modifier. (orig.)

  5. Friction stir processing (FSP: refining microstructures and improving properties

    Directory of Open Access Journals (Sweden)

    McNelley, T. R.

    2010-12-01

    Full Text Available FSP is reviewed as an allied technology of friction stir welding (FSW and additional considerations such as processing pattern and step over distance are introduced. The application of FSP to continuously cast AA5083 material in the as-cast condition is described and the extent of grain refinement and homogenization of microstructure is documented. The FSP-induced superplastic response of this material is compared to the response of conventionally processed AA5083 and the improved ductility of the FSP material is related to grain refinement and microstructure homogenization.

    Se revisa el procesado por fricción batida (FSP como un aliado tecnológico de la soldadura por fricción batida (FSW y se introducen consideraciones adicionales tales como el patrón de procesado y el paso en función de la distancia. Se describe la aplicación de FSP al material AA5083 por colada continua en la condición de colada y se documenta el grado de afino de grano y homogeneización de la microestructura. La respuesta de superplasticidad inducida por FSP se compara con la respuesta de la aleación AA5083 procesada convencionalmente y la mejora de ductilidad del material FSP se relaciona con el afino de grano y la homogeneización de la microestructura.

  6. Note: Additionally refined new possibilities of plasma probe diagnostics

    Science.gov (United States)

    Riaby, V. A.; Savinov, V. P.; Masherov, P. E.; Yakunin, V. G.

    2018-03-01

    In two previous Notes published in this journal, a method of measuring probe sheath thickness and ion mass was described using Langmuir probe diagnostics in low pressure xenon plasma close to Maxwellian substance. According to the first Note, this method includes two stages: (i) in a special experiment with known ion mass, the Bohm and Child-Langmuir-Boguslavsky (CLB) equations for cylindrical Langmuir probes used in this xenon plasma were solved jointly to determine the probe sheath thicknesses and Bohm coefficient CBCyl ≈ 1.13; and (ii) in a general experiment, with known CBCyl, the same equations could be solved to obtain the probe sheath thicknesses and the mean ion mass. In the second Note, the (i) stage of this method was refined: the results of the CLB probe sheath model application, which were termed "evaluations," were corrected using the step-front probe sheath model, which was closer to reality in the special experiment with the xenon plasma. This process resulted in a Bohm coefficient of CBCyl ≈ 1.23 for the cylindrical probe. In the present Note, corrected xenon plasma parameters without the influence of the bare probe protective shield were used for the (i) stage of this diagnostic method. This action also refined the Bohm coefficient, lowering it to CBCyl ≈ 0.745 for cylindrical probes. This advance makes the new diagnostics method more objective and reliable.

  7. Refining intra-protein contact prediction by graph analysis

    Directory of Open Access Journals (Sweden)

    Eyal Eran

    2007-05-01

    Full Text Available Abstract Background Accurate prediction of intra-protein residue contacts from sequence information will allow the prediction of protein structures. Basic predictions of such specific contacts can be further refined by jointly analyzing predicted contacts, and by adding information on the relative positions of contacts in the protein primary sequence. Results We introduce a method for graph analysis refinement of intra-protein contacts, termed GARP. Our previously presented intra-contact prediction method by means of pair-to-pair substitution matrix (P2PConPred was used to test the GARP method. In our approach, the top contact predictions obtained by a basic prediction method were used as edges to create a weighted graph. The edges were scored by a mutual clustering coefficient that identifies highly connected graph regions, and by the density of edges between the sequence regions of the edge nodes. A test set of 57 proteins with known structures was used to determine contacts. GARP improves the accuracy of the P2PConPred basic prediction method in whole proteins from 12% to 18%. Conclusion Using a simple approach we increased the contact prediction accuracy of a basic method by 1.5 times. Our graph approach is simple to implement, can be used with various basic prediction methods, and can provide input for further downstream analyses.

  8. Chromatography analysis of Jatropha Curcas L oil raw and refined

    International Nuclear Information System (INIS)

    Chitue de Assuncao Nascimento, Juliano; Lafargue Perez, Francisco; Diaz Velazquez, Manuel

    2013-01-01

    The chromatography of gases is one of the most versatile methods utilized in the chemical laboratory, which permits the determinations of the percentages and types of fatty acids present in vegetable oils. The objective of this work was to carry out a comparative study of the composition of the fatty acids, of the mechanically extracted oil from the seed of the Jatropha curcas L plant in the raw and refined state, using the data obtained by gas chromatography. The fatty acids of the oil were determined as methylic esteres. The analyst was carried out in a gas chromatographer, with a detector of ionization by way of flame (FID), Agilent 7890A (Agilent, USA) coupled to HP Pentium 4 computer, with a data processing program. The temperatures of the injector and of the detector were 250℃ and 260℃ respectively. The data obtained chromatographically of the oil of Jatropha curcas L, raw and refined indicates that the refinery process did not vary the composition of the fatty acid, because there are no significant differences between them. Also, the results obtained by other investigators, showed that the predominant fatty acids obtained from the oil of the Jatropha curcas L were palmitic and stearic in the saturated fatty acids, and oleic and linoleic in the unsaturated fatty acids

  9. Chromatography Analysis of Jatropha Curcas L Oil Raw and Refined

    International Nuclear Information System (INIS)

    Chitue de Assuncao Nascimento, Juliano; Lafargue Perez, Francisco; Diaz Velazquez, Manuel

    2013-01-01

    The chromatography of gases is one of the most versatile methods utilized in the chemical laboratory, which permits the determinations of the percentages and types of fatty acids present in vegetable oils. The objective of this work was to carry out a comparative study of the composition of the fatty acids, of the mechanically extracted oil from the seed of the Jatropha curcas L plant in the raw and refined state, using the data obtained by gas chromatography. The fatty acids of the oil were determined as methylic esteres. The analyst was carried out in a gas chromatographer, with a detector of ionization by way of flame (FID), Agilent 7890A (Agilent, USA) coupled to HP Pentium 4 computer, with a data processing program. The temperatures of the injector and of the detector were 250 °C and 260 °C respectively. The data obtained chromatographically of the oil of Jatropha curcas L, raw and refined indicates that the refinery process did not vary the composition of the fatty acid, because there are no significant differences between them. Also, the results obtained by other investigators, showed that the predominant fatty acids obtained from the oil of the Jatropha curcas L were palmitic and stearic in the saturated fatty acids, and oleic and linoleic in the unsaturated fatty acids

  10. Investment in exploration-production and refining 2013

    International Nuclear Information System (INIS)

    Hureau, Geoffroy; Serbutoviez, Sylvain; Silva, Constancio; Maisonnier, Guy

    2013-10-01

    IFPEN analyses in this study the 2013 evolution of global investment in the field of exploration-production and refining. 1 - Changes in oil and gas prices; 2 - Exploration production: a new year of growth: the increase in investments continues into 2013, exploration - Discoveries in 2013, 1978 - 2012: Investments - Production - Price; 3 - Main markets in the upstream oil equipment and services sector: introduction, drilling (Drilling activity, Number of wells drilled throughout the world, Number of onshore wells, Number of offshore wells, Drilling markets, equipment and services for wells, Onshore drilling market, Offshore drilling market, Fracking market); Geophysical market (Geophysical activity, Geophysical market); Offshore construction (Offshore construction activities, Fixed platforms (Jack-ups), Floating Platform Systems (FPS), Sub-sea constructions, Offshore construction market); Conclusion; 4 - Refining: looking for new equilibriums: falling excess capacity and regional disparities, recovery in capital spending in emerging countries, Asia is still the eldorado for investment in the downstream oil Sector (Continuing overcapacity in the medium-term, Differing investment strategies)

  11. Mesh refinement of simulation with the AID riser transmission gamma

    International Nuclear Information System (INIS)

    Lima Filho, Hilario J.B. de; Benachour, Mohand; Dantas, Carlos C.; Brito, Marcio F.P.; Santos, Valdemir A. dos

    2013-01-01

    Type reactors Circulating Fluidized Bed (CFBR) vertical, in which the particulate and gaseous phases have flows upward (riser) have been widely used in gasification processes, combustion and fluid catalytic cracking (FCC). These biphasic reactors (gas-solid) efficiency depends largely on their hydrodynamic characteristics, and shows different behaviors in the axial and radial directions. The solids axial distribution is observed by the higher concentration in the base, getting more diluted toward the top. Radially, the solids concentration is characterized as core-annular, in which the central region is highly diluted, consisting of dispersed particles and fluid. In the present work developed a two-dimensional geometry (2D) techniques through simulations in computational fluid dynamics (CFD) to predict the gas-solid flow in the riser type CFBR through transient modeling, based on the kinetic theory of granular flow . The refinement of computational meshes provide larger amounts of information on the parameters studied, but may increase the processing time of the simulations. A minimum number of cells applied to the mesh construction was obtained by testing five meshes. The validation of the hydrodynamic parameters was performed using a range of 241Am source and detector NaI (Tl). The numerical results were provided consistent with the experimental data, indicating that the refined computational mesh in a controlled manner, improve the approximation of the expected results. (author)

  12. Success in Asian refining -- Strategies for a growth industry

    International Nuclear Information System (INIS)

    Burke, B.F.

    1994-01-01

    Asia offers some of the best growth opportunities to the global refining industry. Many of its nations are in the process of industrializing, with a rapid rise in living standards and associated energy use. Growth trends are firmly established, with petroleum use in particular increasing rapidly as modern transport infrastructures develop. Of perhaps greater importance is Asia's potential for continued growth based on population and GDP trends. While the expected growth offers a wide range of opportunities, succeeding in the unique Asian marketplace will be a challenge mastered by only a few new entrants. This paper will examine some of the critical issues that will drive success and shape the refining business in Asia. Industry fundamentals will be reviewed, with a focus on growth and profit drivers. With the fundamental framework established, the unique challenges posed by the Asian environment, including cultural issues, investment requirements, regulatory trends and issues in market development will be discussed. The ability to succeed in Asia by identifying factors that create local advantage within a very diverse region will be discussed. The need to merge corporate capabilities and objectives with regional opportunities is the key requirement to succeed in entering or expanding in the region

  13. Panorama 2010: Refining: Adjusting to a changing business environment

    International Nuclear Information System (INIS)

    Silva, C.

    2010-01-01

    During the latter half of 2008, the sharp deterioration in the economic situation translated into a decline in world oil demand and, after a certain time lag, a collapse in refining margins. In 2009, this downtrend continued and was aggravated by the emergence of large amounts of surplus capacity. For one thing, the investment programs undertaken in recent years to cover growing demand for petroleum products cannot be discontinued in an abrupt manner. For another, the growth rate in 2009 was obviously flagging and inertia was strong, contributing to the accumulation of excess capacity. In the OECD countries, the current slump is expected to persist. In the medium term, a reorganization of the sector is anticipated, especially in Europe and in the United States: refining capacity will be scaled back and more stringent refinery emissions standards (SO 2 , CO 2 quota) and fuel specifications (sulfur content in bunker fuels) will be enforced. Projects will gravitate even more towards the regions of high-growth demand: the bulk of new capacity will be located in Asia. (author)

  14. Protein homology model refinement by large-scale energy optimization.

    Science.gov (United States)

    Park, Hahnbeom; Ovchinnikov, Sergey; Kim, David E; DiMaio, Frank; Baker, David

    2018-03-20

    Proteins fold to their lowest free-energy structures, and hence the most straightforward way to increase the accuracy of a partially incorrect protein structure model is to search for the lowest-energy nearby structure. This direct approach has met with little success for two reasons: first, energy function inaccuracies can lead to false energy minima, resulting in model degradation rather than improvement; and second, even with an accurate energy function, the search problem is formidable because the energy only drops considerably in the immediate vicinity of the global minimum, and there are a very large number of degrees of freedom. Here we describe a large-scale energy optimization-based refinement method that incorporates advances in both search and energy function accuracy that can substantially improve the accuracy of low-resolution homology models. The method refined low-resolution homology models into correct folds for 50 of 84 diverse protein families and generated improved models in recent blind structure prediction experiments. Analyses of the basis for these improvements reveal contributions from both the improvements in conformational sampling techniques and the energy function.

  15. Iterative feature refinement for accurate undersampled MR image reconstruction

    Science.gov (United States)

    Wang, Shanshan; Liu, Jianbo; Liu, Qiegen; Ying, Leslie; Liu, Xin; Zheng, Hairong; Liang, Dong

    2016-05-01

    Accelerating MR scan is of great significance for clinical, research and advanced applications, and one main effort to achieve this is the utilization of compressed sensing (CS) theory. Nevertheless, the existing CSMRI approaches still have limitations such as fine structure loss or high computational complexity. This paper proposes a novel iterative feature refinement (IFR) module for accurate MR image reconstruction from undersampled K-space data. Integrating IFR with CSMRI which is equipped with fixed transforms, we develop an IFR-CS method to restore meaningful structures and details that are originally discarded without introducing too much additional complexity. Specifically, the proposed IFR-CS is realized with three iterative steps, namely sparsity-promoting denoising, feature refinement and Tikhonov regularization. Experimental results on both simulated and in vivo MR datasets have shown that the proposed module has a strong capability to capture image details, and that IFR-CS is comparable and even superior to other state-of-the-art reconstruction approaches.

  16. Conjoined use of EM and NMR in RNA structure refinement.

    Directory of Open Access Journals (Sweden)

    Zhou Gong

    Full Text Available More than 40% of the RNA structures have been determined using nuclear magnetic resonance (NMR technique. NMR mainly provides local structural information of protons and works most effectively on relatively small biomacromolecules. Hence structural characterization of large RNAs can be difficult for NMR alone. Electron microscopy (EM provides global shape information of macromolecules at nanometer resolution, which should be complementary to NMR for RNA structure determination. Here we developed a new energy term in Xplor-NIH against the density map obtained by EM. We conjointly used NMR and map restraints for the structure refinement of three RNA systems—U2/U6 small-nuclear RNA, genome-packing motif (Ψ(CD2 from Moloney murine leukemia virus, and ribosome-binding element from turnip crinkle virus. In all three systems, we showed that the incorporation of a map restraint, either experimental or generated from known PDB structure, greatly improves structural precision and accuracy. Importantly, our method does not rely on an initial model assembled from RNA duplexes, and allows full torsional freedom for each nucleotide in the torsion angle simulated annealing refinement. As increasing number of macromolecules can be characterized by both NMR and EM, the marriage between the two techniques would enable better characterization of RNA three-dimensional structures.

  17. Iterative feature refinement for accurate undersampled MR image reconstruction

    International Nuclear Information System (INIS)

    Wang, Shanshan; Liu, Jianbo; Liu, Xin; Zheng, Hairong; Liang, Dong; Liu, Qiegen; Ying, Leslie

    2016-01-01

    Accelerating MR scan is of great significance for clinical, research and advanced applications, and one main effort to achieve this is the utilization of compressed sensing (CS) theory. Nevertheless, the existing CSMRI approaches still have limitations such as fine structure loss or high computational complexity. This paper proposes a novel iterative feature refinement (IFR) module for accurate MR image reconstruction from undersampled K-space data. Integrating IFR with CSMRI which is equipped with fixed transforms, we develop an IFR-CS method to restore meaningful structures and details that are originally discarded without introducing too much additional complexity. Specifically, the proposed IFR-CS is realized with three iterative steps, namely sparsity-promoting denoising, feature refinement and Tikhonov regularization. Experimental results on both simulated and in vivo MR datasets have shown that the proposed module has a strong capability to capture image details, and that IFR-CS is comparable and even superior to other state-of-the-art reconstruction approaches. (paper)

  18. Mesh refinement of simulation with the AID riser transmission gamma

    Energy Technology Data Exchange (ETDEWEB)

    Lima Filho, Hilario J.B. de; Benachour, Mohand; Dantas, Carlos C.; Brito, Marcio F.P., E-mail: hilariojorge2005@yahoo.com.br, E-mail: ccd@ufpe.br [Universidade Federal de Pernambuco (UFPE), Pernambuco, PE (Brazil); Santos, Valdemir A. dos, E-mail: vas@unicap.br [Universidade Catolica de Pernambuco (CCT/UNICAP), Pernambuco, PE (Brazil). Dept. de Engenharia Quimica

    2013-07-01

    Type reactors Circulating Fluidized Bed (CFBR) vertical, in which the particulate and gaseous phases have flows upward (riser) have been widely used in gasification processes, combustion and fluid catalytic cracking (FCC). These biphasic reactors (gas-solid) efficiency depends largely on their hydrodynamic characteristics, and shows different behaviors in the axial and radial directions. The solids axial distribution is observed by the higher concentration in the base, getting more diluted toward the top. Radially, the solids concentration is characterized as core-annular, in which the central region is highly diluted, consisting of dispersed particles and fluid. In the present work developed a two-dimensional geometry (2D) techniques through simulations in computational fluid dynamics (CFD) to predict the gas-solid flow in the riser type CFBR through transient modeling, based on the kinetic theory of granular flow . The refinement of computational meshes provide larger amounts of information on the parameters studied, but may increase the processing time of the simulations. A minimum number of cells applied to the mesh construction was obtained by testing five meshes. The validation of the hydrodynamic parameters was performed using a range of 241Am source and detector NaI (Tl). The numerical results were provided consistent with the experimental data, indicating that the refined computational mesh in a controlled manner, improve the approximation of the expected results. (author)

  19. The hydrogen market in refining and petrochemicals in France

    International Nuclear Information System (INIS)

    Lutz, P.; Borel, P.

    1991-11-01

    The french hydrogen market on industrial sites can be divided into three main parts. Captive hydrogen is produced by thermofor catalytic reforming, catalytic cracking and hydrotreating of vacuum distillates, and is consumed in hydrotreating of petrol, hydrodesulfurization of gasoil and domestic fuel oil, hydrocracking and hydrofining of lubricants. By-product hydrogen is burnt in boilers and flare stacks. Merchant hydrogen is sold to users on the open market. Currently, thirteen refineries belonging to six companies produce 73 million tonnes of petroleum products each year in France and release annually a surplus of some 100,000 tonnes of hydrogen. The future of refining industry in France depends on the quality of the crude oil, the specific characteristics of the end products, and the developments in user markets. The refining process is likely to become more complex by 2005 with an increase in hydrogen requirements. Refineries could then undergo an annual deficit between 140,000 and 230,000 tonnes of hydrogen. The choice of the appropriate process to cover this shortfall depends mostly on oil companies strategy. (author). 1 fig., 3 tabs., 3 diagrams

  20. Environmental monitoring program design for uranium refining and conversion operations

    International Nuclear Information System (INIS)

    1984-08-01

    The objective of this study was to develop recommendations for the design of environmental monitoring programs at Canadian uranium refining and conversion operations. In order to develop monitoring priorities, chemical and radioactive releases to the air and water were developed for reference uranium refining and conversion facilities. The relative significance of the radioactive releases was evaluated through a pathways analysis which estimated dose to individual members of the critical receptor group. The effects of chemical releases to the environment were assessed by comparing predicted air and water contaminant levels to appropriate standards or guidelines. For the reference facilities studied, the analysis suggested that environmental effects are likely to be dominated by airborne release of both radioactive and nonradioactive contaminants. Uranium was found to be the most important radioactive species released to the air and can serve as an overall indicator of radiological impacts for any of the plants considered. The most important nonradioactive air emission was found to be fluoride (as hydrogen fluoride) from the uranium hexafluoride plant. For the uranium trioxide and uranium dioxide plants, air emissions of oxides of nitrogen were considered to be most important. The study recommendations for the design of an environmental monitoring program are based on consideration of those factors most likely to affect local air and water quality, and human radiation exposure. Site- and facility-specific factors will affect monitoring program design and the selection of components such as sampling media, locations and frequency, and analytical methods

  1. Interactive visual exploration and refinement of cluster assignments.

    Science.gov (United States)

    Kern, Michael; Lex, Alexander; Gehlenborg, Nils; Johnson, Chris R

    2017-09-12

    With ever-increasing amounts of data produced in biology research, scientists are in need of efficient data analysis methods. Cluster analysis, combined with visualization of the results, is one such method that can be used to make sense of large data volumes. At the same time, cluster analysis is known to be imperfect and depends on the choice of algorithms, parameters, and distance measures. Most clustering algorithms don't properly account for ambiguity in the source data, as records are often assigned to discrete clusters, even if an assignment is unclear. While there are metrics and visualization techniques that allow analysts to compare clusterings or to judge cluster quality, there is no comprehensive method that allows analysts to evaluate, compare, and refine cluster assignments based on the source data, derived scores, and contextual data. In this paper, we introduce a method that explicitly visualizes the quality of cluster assignments, allows comparisons of clustering results and enables analysts to manually curate and refine cluster assignments. Our methods are applicable to matrix data clustered with partitional, hierarchical, and fuzzy clustering algorithms. Furthermore, we enable analysts to explore clustering results in context of other data, for example, to observe whether a clustering of genomic data results in a meaningful differentiation in phenotypes. Our methods are integrated into Caleydo StratomeX, a popular, web-based, disease subtype analysis tool. We show in a usage scenario that our approach can reveal ambiguities in cluster assignments and produce improved clusterings that better differentiate genotypes and phenotypes.

  2. A refined model for characterizing x-ray multilayers

    International Nuclear Information System (INIS)

    Oren, A.L.; Henke, B.L.

    1987-12-01

    The ability to quickly and accurately characterize arbitrary multilayers is very valuable for not only can we use the characterizations to predict the reflectivity of a multilayer for any soft x-ray wavelength, we also can generalize the results to apply to other multilayers of the same type. In addition, we can use the characterizations as a means of evaluating various sputtering environments and refining sputtering techniques to obtain better multilayers. In this report we have obtained improved characterizations for sample molybdenum-silicon and vanadium-silicon multilayers. However, we only examined five crystals overall, so the conclusions that we could draw about the structure of general multilayers is limited. Research involving many multilayers manufactured under the same sputtering conditions is clearly in order. In order to best understand multilayer structures it may be necessary to further refine our model, e.g., adopting a Gaussian form for the interface regions. With such improvements we can expect even better agreement with experimental values and continued concurrence with other characterization techniques. 18 refs., 30 figs., 7 tabs

  3. Parametric Rietveld refinement applied to in situ diffraction studies

    International Nuclear Information System (INIS)

    Styles, M.J.; Riley, D.P.

    2009-01-01

    Full text: In-situ diffraction studies in which data is collected as a function of a particular external variable (for example time or temperature), are often conducted with the aim of developing models to predict the response of materials to certain operational or processing conditions. The traditional approach to analysing powder diffraction data collected in this manner is to refine a model of each pattern independently using the Rietveld method [1] and progress through the data sets sequentially. Obtaining accurate results via this method can be problematic, particularly in instances where the nature of the material system is such that data must be collected under less than ideal circumstances [2]. An alternative approach is to take advantage of known relationships between parameters to describe their evolution over the entire collection of diffraction data [3]. The total number of independent parameters is hence reduced, enabling a large number of data sets to be analysed simultaneously and models of material behaviour to be refined directly. This approach has recently been used to extract accurate measurements of sample temperature from neutron and synchrotron powder diffraction data of reacting carbide and oxide systems, and to stabilise the analysis of phase composition as a function of time for the purposes of kinetic modelling.

  4. Carbothermic Reduction of Amorphous Silica Refined from Diatomaceous Earth

    Science.gov (United States)

    Hakamada, Masataka; Fukunaka, Yasuhiro; Oishi, Toshio; Nishiyama, Takashi; Kusuda, Hiromu

    2010-04-01

    Aimed at developing solar-grade Si (SOG-Si) resources, amorphous silica (AS) refined from diatomaceous earth was reduced carbothermically. The reactivity of quartz—typically crystalline silica—also was investigated for comparison. Preliminary experiments confirmed an intermediate phase of SiC during the carbothermic reaction. SiC was produced more easily by heating AS mixed with graphite within 2 hours at 1773 K in a resistance furnace, whereas quartz remained unreacted under the same condition. The AS mixed with SiC then was heated in an electrode impulse furnace. An Si peak was identified in the X-ray diffraction (XRD) pattern of the sample reacted within 30 seconds at 2273 K. Chemical analysis indicated that the mole ratio of reduced Si to initial SiO2 increased with a heating time of 15-30 seconds. It almost reached a constant depending on the heating temperature. The initial stage may correspond to a significant reduction from SiO2 to Si in the solid-solid or solid-gas reaction systems. The next stage probably is a slow vaporization of SiO(g). Once the reduced Si melts with SiO2 at the high temperature, the melt partially covers the surface of SiO2 to prevent contact with SiC. A better reactivity for refined AS is observed than for quartz.

  5. 40 CFR 80.555 - What provisions are available to a large refiner that acquires a small refiner or one or more of...

    Science.gov (United States)

    2010-07-01

    ... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA... May 31, 2010 for a refinery acquired from a motor vehicle diesel fuel small refiner or beyond the... motor vehicle diesel fuel small refiner or beyond the dates specified in § 80.554(a) or (b), as...

  6. Impact of Crude Oil Quality on the Refining Conditions and Composition of Nutraceuticals in Refined Palm Oil.

    Science.gov (United States)

    Sampaio, Klicia A; Ayala, Jose Vila; Van Hoed, Vera; Monteiro, Simone; Ceriani, Roberta; Verhé, Roland; Meirelles, Antonio J A

    2017-08-01

    Palm oil is the major vegetable oil used worldwide due to its unique properties. The effect of crude palm oil acidity on the final free fatty acids (FFA) content, neutral oil loss (NOL), and nutraceutical compounds, such as carotenes, total tocols (tocopherols and tocotrienols), squalene, and phytosterols was investigated. A central composite design was employed to study the influence of the refining conditions: temperature (200 to 260 °C), steam percentage (0.5% to 3.5%), and initial FFA content (2.2% to 6.0%) on the quality of the refined product. The results revealed that initial palm oil acidity is a statistically important parameter to obtain commercially acceptable values for final FFA content. The increase of temperature presented the most important effect on the reduction of all nutraceutical compounds. The highest tocopherols (88%), phytosterols (98%), and squalene retention (84%) was obtained when applying the mildest temperature (200 °C). From the experimental results, 3 equations were generated enabling the prediction of the free fatty acids content, the tocols content, and the losses of neutral oil. Therefore, this work contributes to the understanding and optimization of the process for the production of palm oil with high nutraceutical quality and low free fatty acid contents. © 2017 Institute of Food Technologists®.

  7. Metallic Ureteric Stents in Malignant Ureteric Obstruction: a Systematic Review.

    Science.gov (United States)

    Khoo, C C K; Abboudi, H; Cartwright, R; El-Husseiny, T; Dasgupta, R

    2018-02-02

    The effectiveness of metallic stents in the management of malignant ureteric obstruction (MUO) is unclear. This systematic review evaluates the use of four commercially available metallic stents (Resonance, Memokath 051, Uventa and Allium URS). Twenty-one studies met eligibility criteria. Overall success rates ranged from 88% for the Allium stent to 65% for Memokath 051. Resonance demonstrated the lowest migration rate (1%). Uventa had the lowest obstruction rate (6%). Metallic ureteric stents offer a viable alternative in the management of MUO. Further high quality studies are required to assess cost effectiveness and refine specific indications based on aetiology and level of the ureteric obstruction. Copyright © 2018. Published by Elsevier Inc.

  8. Strucute optimale du raffinage Optimum Stucture of Refining in Belgium

    Directory of Open Access Journals (Sweden)

    Jomaux F.

    2006-11-01

    Full Text Available Cet article présente un résumé des méthodes utilisées et des résultats obtenus au cours d'une étude de la structure de l'industrie du raffinage en Belgique, étude qui a fait l'objet d'une thèse de doctorat('. L'objectif était de déterminer, dans ses grandes lignes, l'évolution à long terme des capacités des unités de traitement en raffinerie permettant de satisfaire au moindre coût la demande belge en produits pétroliers. Différents scénarios relatifs à cette demande, ainsi que différentes hypothèses d'approvisionnement en pétroles bruts ont été analysés. L'étude s'est appuyée sur des modèles linéaires de raffinage développés à l'Institut Français du Pétrole (IFP, et dont la mise en ceuvre fait appel à des programmes générateurs de matrices et de rapports, ainsi qu'à des fichiers de données technico-économiques disponibles à l'IFP. L'existence de trois zones de raffinage géographiquement distinctes a conduit à l'utilisation de modèles multi-raffineries intégrant l'approvisionnement des principaux dépôts de distribution. This article reviews the methods used and results obtained during a survey of the structure of the refining industry in Belgium, a survey which is the subject of a doctoral dissertation (1. The aim was to determine the major guidelines of the longterm evolution of the production capacities of refinery processing installations so as to fulfill the Belgian demand for petroleum products at lowest cost. Different scénarios for this demand as well as different crude-oil supply hypotheses are analyzed. The survey is based on linear refining models developed at IFP. These models make use of matrix and report generator programs as well as technico-economic data files available at Institut Français du Pétrole (IFP. The existence of three geographically distinct refining zones leads ta the multi-refinery models integrating deliveries to the main distribution depots.

  9. Grain Refinement of Low Carbon Martensitic Steel by Heat Treatment

    Directory of Open Access Journals (Sweden)

    N. V. Kolebina

    2015-01-01

    Full Text Available The low-carbon steels have good corrosion and technological properties. Hot deformation is the main operation in manufacturing the parts from these steels. So one of the important properties of the material is a property of plasticity. The grain size significantly influences on the ductility properties of steel. The grain size of steel depends on the chemical composition of the crystallization process, heat treatment, and steel machining. There are plenty methods to have grain refinement. However, taking into account the large size of the blanks for the hydro turbine parts, the thermal cycling is an advanced method of the grain refinement adaptable to streamlined production. This work experimentally studies the heat treatment influence on the microstructure of the low-carbon 01X13N04 alloy steel and proposes the optimal regime of the heat treatment to provide a significantly reduced grain size. L.M. Kleiner, N.P. Melnikov and I.N. Bogachyova’s works focused both on the microstructure of these steels and on the influence of its parameters on the mechanical properties. The paper focuses mainly on defining an optimal regime of the heat treatment for grain refinement. The phase composition of steel and temperature of phase transformation were defined by the theoretical analysis. The dilatometric experiment was done to determine the precise temperature of the phase transformations. The analysis and comparison of the experimental data with theoretical data and earlier studies have shown that the initial sample has residual stress and chemical heterogeneity. The influence of the heat treatment on the grain size was studied in detail. It is found that at temperatures above 950 ° C there is a high grain growth. It is determined that the optimal number of cycles is two. The postincreasing number of cycles does not cause further reducing grain size because of the accumulative recrystallization process. Based on the results obtained, the thermal cycling

  10. Local Refinement of the Super Element Model of Oil Reservoir

    Directory of Open Access Journals (Sweden)

    A.B. Mazo

    2017-12-01

    Full Text Available In this paper, we propose a two-stage method for petroleum reservoir simulation. The method uses two models with different degrees of detailing to describe hydrodynamic processes of different space-time scales. At the first stage, the global dynamics of the energy state of the deposit and reserves is modeled (characteristic scale of such changes is km / year. The two-phase flow equations in the model of global dynamics operate with smooth averaged pressure and saturation fields, and they are solved numerically on a large computational grid of super-elements with a characteristic cell size of 200-500 m. The tensor coefficients of the super-element model are calculated using special procedures of upscaling of absolute and relative phase permeabilities. At the second stage, a local refinement of the super-element model is constructed for calculating small-scale processes (with a scale of m / day, which take place, for example, during various geological and technical measures aimed at increasing the oil recovery of a reservoir. Then we solve the two-phase flow problem in the selected area of the measure exposure on a detailed three-dimensional grid, which resolves the geological structure of the reservoir, and with a time step sufficient for describing fast-flowing processes. The initial and boundary conditions of the local problem are formulated on the basis of the super-element solution. This approach allows us to reduce the computational costs in order to solve the problems of designing and monitoring the oil reservoir. To demonstrate the proposed approach, we give an example of the two-stage modeling of the development of a layered reservoir with a local refinement of the model during the isolation of a water-saturated high-permeability interlayer. We show a good compliance between the locally refined solution of the super-element model in the area of measure exposure and the results of numerical modeling of the whole history of reservoir

  11. Determination of trace elements in refined gold samples by inductively coupled plasma atomic emission spectrometry

    Directory of Open Access Journals (Sweden)

    Steharnik Mirjana

    2013-01-01

    Full Text Available This paper presents a method for determination the trace contents of silver, copper, iron, palladium, zinc and platinum in refined gold samples. Simultaneous inductively coupled plasma atomic emission spectrometer with radial torch position and cross flow nebulizer was used for determination. In order to compare the different calibration strategies, two sets of calibration standards were prepared. The first set was based on matrix matched calibration standards and the second was prepared without the addition of matrix material. Detection limits for matrix matching calibrations were higher for some elements than those without matrix matching. In addition, the internal standardization method was applied and experiments indicated that indium was the best option as internal standard. The obtained results for gold sample by matrix matching and matrix free calibrations were compared with the obtained results by standard addition method. The accuracy of the methods was tested performing recovery test. Recoveries for spiked sample were in the range of 90-115 %. The accuracy of the methods was also tested by analysis of certified reference material of high pure goldAuGHP1. The best results were achieved by matrix free calibration and standard addition method using indium as internal standard at wavelength of 230 nm. [Projekat Ministarstva nauke Republike Srbije, br. 34024: Development of Technologies for Recycling of Precious, Rare and Associated Metals from Solid Waste in Serbia to High Purity Products

  12. Producing novel edible films from semi refined carrageenan (SRC) and ulvan polysaccharides for potential food applications.

    Science.gov (United States)

    Ganesan, Abirami R; Shanmugam, M; Bhat, Rajeev

    2018-02-15

    Edible films were developed from seaweed polysaccharides (Kappaphycus alvarezii and Ulva fasciata). The total extracted yield of semi refined carrageenan (SRC) and ulvan polysaccharide was 31.55%, and 28.86%, with total carbohydrate being 78.08% and 82.43% in SRC and ulvan polysaccharides. Results of viscometric studies revealed molecular weight to be 210 kDa and 72 kDa for SRC and ulvan polysaccharides. Proton NMR studies showed presence of anhydro-d-galactopyranose and glucosidic linkages in SRC, while ulvan polysaccharide had rhamnose-3-sulfate, glucosyl and β-d-glucuronic acid. Three different films developed from SRC and ulvan polysaccharides [SRC, ulvan polysaccharide and combination of SRC and ulvan polysaccharide films] with glycerol. FT-IR spectra confirmed functional group of all the edible films which corresponds with NMR results. Water vapor permeability of films indicated a range of 7.82 to 9.96 × 10-8 gm -1  s -1  Pa -1 with high tensile strength varying between 36.78 and 49.12 MPa. Results on antioxidant activity indicated a strong hydroxyl radical scavenging activity detected in ulvan polysaccharide based film, while metal ion chelating activity was higher in films with a combination of SRC and ulvan polysaccharides. Further, low molecular weight films had better antioxidant activity, while high molecular weight films possessed good mechanical properties. Copyright © 2017. Published by Elsevier B.V.

  13. Research on utilization of isotopes for metallic materials

    International Nuclear Information System (INIS)

    Maebashi, Yoichi; Kagaya, Yutaka; Kametani, Hiroshi

    1983-01-01

    As the research on the utilization of unsealed radioisotopes for metallic materials, among the refining of nonferrous metals already carried out in the National Research Institute for Metals, the refining reaction of copper sulfide was taken up. In this refining reaction, it is important to know the oxidation behavior of sulfur in copper sulfide for improving the refining method. However in the oxidation of sulfur, the kinds of the oxides formed are many, and when copper and iron ions coexist as in this case, their separation and analysis are very difficult. The utilization of radioisotopes is required for identifying the oxidation products and the oxides in melt, and for identifying various compound ions. The solvent for thin layer chromatography was selected, and the effects exerted by the moving rate, concentration and coexisting elements of various sulfur acid ions on the thin layer of silica gel were clarified. In the suspension reaction of copper sulfide without a power source, it was elucidated that S 2 O 3 2- arose consistently from the initial stage of reaction, and the reaction equation was forecast. The melting state of sulfur in anode oxidation reaction was studied. (Kako, I.)

  14. Effects of Inclusions and Austenite Grain Size on the Impact Behavior of a Newly Developed Low-Carbon Steel Weld Metal

    National Research Council Canada - National Science Library

    Blackburn, J

    1999-01-01

    ... carbon steel weld metal was determined. It was concluded that austenite grain refinement was effective at improving toughness across the entire test temperature region, with the exception of the upper shelf energy when the inclusion count...

  15. Block-structured Adaptive Mesh Refinement - Theory, Implementation and Application

    Directory of Open Access Journals (Sweden)

    Deiterding Ralf

    2011-12-01

    Full Text Available Structured adaptive mesh refinement (SAMR techniques can enable cutting-edge simulations of problems governed by conservation laws. Focusing on the strictly hyperbolic case, these notes explain all algorithmic and mathematical details of a technically relevant implementation tailored for distributed memory computers. An overview of the background of commonly used finite volume discretizations for gas dynamics is included and typical benchmarks to quantify accuracy and performance of the dynamically adaptive code are discussed. Large-scale simulations of shock-induced realistic combustion in non-Cartesian geometry and shock-driven fluid-structure interaction with fully coupled dynamic boundary motion demonstrate the applicability of the discussed techniques for complex scenarios.

  16. Changing profile of excimer laser coronary angioplasty: refinements in catheters

    Science.gov (United States)

    Bittl, John A.

    1994-07-01

    During more than five years of investigation with excimer laser angioplasty, several changes have been made in patient selection and laser catheters. It is unclear, however, whether these changes have improved the outcome of excimer laser angioplasty. A total of 2041 patients underwent treatment with excimer laser coronary angioplasty for 2324 lesions with clinical success in 89%, ischemic complications in 7.5%, and vessel perforation in 2.1%. When the entire 5-year period of investigation was divided into four discrete phases, as defined by the successive release of improved laser catheters (prototype, flexible, extremely flexible, and eccentric), clinical success was seen to improve from 86% to 95% (page (pequals0.01) and unstable angina (pdecreased complications. Reduced catheter size relative to vessel size was associated with decreased risk of vessel perforation. Thus, refinements in patient selection and in laser technique have been associated with enhanced safety and efficacy of excimer laser angioplasty.

  17. Rietveld refinement of a natural cobaltian mansfieldite from synchrotron data

    Directory of Open Access Journals (Sweden)

    Giovanni Pratesi

    2009-02-01

    Full Text Available A structural refinement of a natural sample of a Co-bearing mansfieldite, AlAsO4·2H2O [aluminium orthoarsenate(V dihydrate], has been performed based on synchrotron powder diffraction data, with 5% of the octahedral Al sites replaced by Co. Mansfieldite is the aluminium analogue and an isotype of the mineral scorodite (FeAsO4·2H2O, with which it forms a solid solution. The framework structure is based on AsO4 tetrahedra sharing their vertices with AlO4(H2O2 octahedra. Three of the four H atoms belonging to the two water molecules in cis positions take part in O—H...O hydrogen bonding.

  18. MICROARRAY IMAGE GRIDDING USING GRID LINE REFINEMENT TECHNIQUE

    Directory of Open Access Journals (Sweden)

    V.G. Biju

    2015-05-01

    Full Text Available An important stage in microarray image analysis is gridding. Microarray image gridding is done to locate sub arrays in a microarray image and find co-ordinates of spots within each sub array. For accurate identification of spots, most of the proposed gridding methods require human intervention. In this paper a fully automatic gridding method which enhances spot intensity in the preprocessing step as per a histogram based threshold method is used. The gridding step finds co-ordinates of spots from horizontal and vertical profile of the image. To correct errors due to the grid line placement, a grid line refinement technique is proposed. The algorithm is applied on different image databases and results are compared based on spot detection accuracy and time. An average spot detection accuracy of 95.06% depicts the proposed method’s flexibility and accuracy in finding the spot co-ordinates for different database images.

  19. Algorithm refinement for stochastic partial differential equations I. linear diffusion

    CERN Document Server

    Alexander, F J; Tartakovsky, D M

    2002-01-01

    A hybrid particle/continuum algorithm is formulated for Fickian diffusion in the fluctuating hydrodynamic limit. The particles are taken as independent random walkers; the fluctuating diffusion equation is solved by finite differences with deterministic and white-noise fluxes. At the interface between the particle and continuum computations the coupling is by flux matching, giving exact mass conservation. This methodology is an extension of Adaptive Mesh and Algorithm Refinement to stochastic partial differential equations. Results from a variety of numerical experiments are presented for both steady and time-dependent scenarios. In all cases the mean and variance of density are captured correctly by the stochastic hybrid algorithm. For a nonstochastic version (i.e., using only deterministic continuum fluxes) the mean density is correct, but the variance is reduced except in particle regions away from the interface. Extensions of the methodology to fluid mechanics applications are discussed.

  20. Generation expansion planning of the utility with refined immune algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Sung-Ling; Tsay, Ming-Tong [Department of Electrical Engineering, Cheng-Shiu University, Kaohsiung, Taiwan (ROC); Zhan, Tung-Sheng [Department of Electrical Engineering, Kao-Yuan Institute of Technology, Kaohsiung, Taiwan (ROC)

    2006-01-15

    This paper proposes a decision tool for utilities to perform the optimal generation expansion planning in a deregulated electricity market. Combining the immune algorithm (IA) and Tabu search (TS) an refined immune algorithm (RIA) is developed to solve this problem. By considering the various load types (peak load, middle load, basic load) and independent power producers (IPPs) competition, the generation expansion planning model is established under the operational constraints, reliability constraints and CO{sub 2} constraints. RIA is conducted by an improved crossover and mutation mechanism with a competition and auto-adjust scheme to avoid prematurity. Tabu lists with heuristic rules are also employed in the searching process to enhance the performance. Testing results show that RIA can offer a better tool for generation expansion planning of utilities and promoted the competition ability of company. (author)

  1. The new French uranium refining plant at Narbonne

    International Nuclear Information System (INIS)

    Roux, J.

    1961-01-01

    In 1957 the Commissariat l'Energie Atomique in collaboration with two French industrial firms, the Compagnie de Saint-Gobain and the Societe Potasse et Engrais chimique, undertook the construction of a plant for the production of refined uranium on an industrial scale. This plant, which forms part of the French nuclear equipment programme and which works at a capacity of 1000 tons/year, was put into operation in July 1959. First of all the principles on which this under-taking is based are outlined. This is followed by a more detailed account of the construction, including the improvements brought to the process developed at the C.E.A. plant at le Bouchet when it was carried over to the industrial stage by the uranium branch of the Societe d'Etudes et de Travaux. (author) [fr

  2. Air Quality Impacts of Petroleum Refining and Petrochemical Industries

    Directory of Open Access Journals (Sweden)

    Aiswarya Ragothaman

    2017-09-01

    Full Text Available Though refineries and petrochemical industries meet society’s energy demands and produce a range of useful chemicals, they can also affect air quality. The World Health Organization (WHO has identified polluted air as the single largest environmental risk, and hence it is necessary to strive for and maintain good air quality. To manage potential health impacts, it is important to implement proper air quality management by understanding the link between specific pollutant sources and resulting population exposures. These industries release pollutants such as Volatile Organic Compounds, greenhouse gases and particulate matter, from various parts of their operations. Air quality should be monitored and controlled more meticulously in developing nations where increased energy demands, industrialization and overpopulation has led to more emissions and lower air quality. This paper presents a review of findings and highlights from various studies on air quality impacts of petroleum refining and petrochemical plants in many regions in the world.

  3. Refinement of Telemetry for Measuring Blood Pressure in Conscious Rats

    Science.gov (United States)

    Braga, Valdir A; Prabhakar, Nanduri R

    2009-01-01

    Although considered the ‘gold standard’ for measuring blood pressure in laboratory animals, telemetry would benefit from refinement. In the present study, we tested the hypothesis that the small telemetric device used for blood pressure recording in mice would work for rats as well and would serve as an alternative for those studies where abdominal cavity space is quite limited (such as in young animals and pregnant females). Here we report that the use of a smaller and lighter telemetric device implanted in the abdominal aorta of rats led to acquisition of stable and high-quality blood pressure and heart rate data, similar to those obtained by using a larger telemetric device developed for rats. The use of smaller transmitters represents an alternative telemetry technique, especially for those cases in which space in the abdominal cavity is particularly limited such as during pregnancy. PMID:19476715

  4. The European Refining Crisis: what is at stake for Europe?

    International Nuclear Information System (INIS)

    Boncourt, Maite de

    2013-03-01

    he European Refining sector is in crisis. The wave of refineries closures has spared no EU Member States. In less than five years, eleven refineries were simply shut down and no less than seventeen changed ownership in the UK, in France, in Germany, in the Netherlands, in Sweden or in Spain. As closure is a last resort measure, given its high costs, this gives an indication of the situation's seriousness. The present situation reflects more than just the widespread effects of the economic crisis. If the sector has always been known as cyclical, the change however comes from the shift in demand and trade patterns for oil products. In the ongoing globalization of the oil market products, Europe appears to be the most vulnerable piece and this raises questions as regard the European security of oil product supplies. (author)

  5. Refined localization of the Prieto-syndrome locus

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, F.; Prieto, F. [Unidad de Genetica, Valencia (Spain); Gal, A. [Universitaets-Krankenhaus Eppendorf, Hamburg (Germany)

    1996-07-12

    PRS designates the locus for a syndromal form of X-linked mental retardation (Prieto syndrome) characterized by minor facial anomalies, ear malformation, abnormal growth of teeth, clinodactyly, sacral dimple, patellar luxation, malformation of lower limbs, abnormalities of the fundus of the eye, and subcortical cerebral atrophy. Linkage analysis localized the disease locus between DXS84 (Xp21.1) and DXS255. Here we present additional linkage data that provide further support and refinement of this localization. Individual III-18 gave birth to a male, currently aged 2 7/12 years, who clearly shows delayed psychomotor development. He began to walk at 23 months and his speech is delayed. In addition, he shows the characteristic facial anomalies, {open_quotes}dysplastic{close_quotes} ears, sacral dimple, and clinodactyly, as do all other affected males in this family. 7 refs., 1 tab.

  6. Non-perturbative effects and the refined topological string

    Energy Technology Data Exchange (ETDEWEB)

    Hatsuda, Yasuyuki [DESY Hamburg (Germany). Theory Group; Tokyo Institute of Technology (Japan). Dept. of Physics; Marino, Marcos [Geneve Univ. (Switzerland). Dept. de Physique Theorique et Section de Mathematiques; Moriyama, Sanefumi [Nagoya Univ. (Japan). Kobayashi Maskawa Inst.; Nagoya Univ. (Japan). Graduate School of Mathematics; Okuyama, Kazumi [Shinshu Univ., Matsumoto, Nagano (Japan). Dept. of Physics

    2013-06-15

    The partition function of ABJM theory on the three-sphere has non-perturbative corrections due to membrane instantons in the M-theory dual. We show that the full series of membrane instanton corrections is completely determined by the refined topological string on the Calabi-Yau manifold known as local P{sup 1} x P{sup 1}, in the Nekrasov-Shatashvili limit. Our result can be interpreted as a first-principles derivation of the full series of non-perturbative effects for the closed topological string on this Calabi-Yau background. Based on this, we make a proposal for the non-perturbative free energy of topological strings on general, local Calabi-Yau manifolds.

  7. Non-perturbative effects and the refined topological string

    International Nuclear Information System (INIS)

    Hatsuda, Yasuyuki; Tokyo Institute of Technology; Marino, Marcos; Moriyama, Sanefumi; Nagoya Univ.; Okuyama, Kazumi

    2013-06-01

    The partition function of ABJM theory on the three-sphere has non-perturbative corrections due to membrane instantons in the M-theory dual. We show that the full series of membrane instanton corrections is completely determined by the refined topological string on the Calabi-Yau manifold known as local P 1 x P 1 , in the Nekrasov-Shatashvili limit. Our result can be interpreted as a first-principles derivation of the full series of non-perturbative effects for the closed topological string on this Calabi-Yau background. Based on this, we make a proposal for the non-perturbative free energy of topological strings on general, local Calabi-Yau manifolds.

  8. Curved mesh generation and mesh refinement using Lagrangian solid mechanics

    Energy Technology Data Exchange (ETDEWEB)

    Persson, P.-O.; Peraire, J.

    2008-12-31

    We propose a method for generating well-shaped curved unstructured meshes using a nonlinear elasticity analogy. The geometry of the domain to be meshed is represented as an elastic solid. The undeformed geometry is the initial mesh of linear triangular or tetrahedral elements. The external loading results from prescribing a boundary displacement to be that of the curved geometry, and the final configuration is determined by solving for the equilibrium configuration. The deformations are represented using piecewise polynomials within each element of the original mesh. When the mesh is sufficiently fine to resolve the solid deformation, this method guarantees non-intersecting elements even for highly distorted or anisotropic initial meshes. We describe the method and the solution procedures, and we show a number of examples of two and three dimensional simplex meshes with curved boundaries. We also demonstrate how to use the technique for local refinement of non-curved meshes in the presence of curved boundaries.

  9. Refining animal experiments: the first Brazilian regulation on animal experimentation.

    Science.gov (United States)

    de A e Tréz, Thales

    2010-06-01

    The very first law on animal experimentation has been approved recently in Brazil, and now is part of a set of the legal instruments that profile the Brazilian government's attitude toward the use of animals in experiments. Law 11794/08 establishes a new legal instrument that will guide new methods of conduct for ethics committees, researchers and representatives of animal protection societies. This comment aims to analyse critically the implications that this law brings to Brazilian reality. The link between it and the Russell and Burch's Three Rs concept is defined, and certain problems are identified. The conclusion is that the body of the law emphasises the refinement of animal experiments, but gives little importance to the principles of reduction and replacement.

  10. Refining of image using self-organizing map with clustering

    Science.gov (United States)

    Dahiya, Neeraj; Dalal, Surjeet; Tanwar, Gundeep

    2016-03-01

    Self Organization Map(SOM) is an automatic tool in data analysis in data mining,it is used to explore the multi-dimentional data which simplifies complexity and produce meaningful relation with each other or high dimentional into low dimentional .the powerful method of SOM i.e learning method results excellent performance .the SOM algorithum have various steps from starting stage to the final neuron and their weight updation and modification, these procedure resultant a lot of compplexity accoording to the parameters on the basis of experiments .this paper will compare and discuss various papameters and their result or factors that can improve and refine the image through varius process of SOM.

  11. Local mesh refinement for incompressible fluid flow with free surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Terasaka, H.; Kajiwara, H.; Ogura, K. [Tokyo Electric Power Company (Japan)] [and others

    1995-09-01

    A new local mesh refinement (LMR) technique has been developed and applied to incompressible fluid flows with free surface boundaries. The LMR method embeds patches of fine grid in arbitrary regions of interest. Hence, more accurate solutions can be obtained with a lower number of computational cells. This method is very suitable for the simulation of free surface movements because free surface flow problems generally require a finer computational grid to obtain adequate results. By using this technique, one can place finer grids only near the surfaces, and therefore greatly reduce the total number of cells and computational costs. This paper introduces LMR3D, a three-dimensional incompressible flow analysis code. Numerical examples calculated with the code demonstrate well the advantages of the LMR method.

  12. Symmetries of the refined D1/D5 BPS spectrum

    Science.gov (United States)

    Benjamin, Nathan; Harrison, Sarah M.

    2017-11-01

    We examine the large N 1/4-BPS spectrum of the symmetric orbifold CFT Sym N ( M ) deformed to the supergravity point in moduli space for M = K3 and T 4. We consider refinement under both left- and right-moving SU(2) R symmetries of the superconformal algebra, and decompose the spectrum into characters of the algebra. We find that at large N the character decomposition satisfies an unusual property, in which the degeneracy only depends on a certain linear combination of left- and right-moving quantum numbers, suggesting deeper symmetry structure. Furthermore, we consider the action of discrete symmetry groups on these degeneracies, where certain subgroups of the Conway group are known to play a role. We also comment on the potential for larger discrete symmetry groups to appear in the large N limit.

  13. Recent developments, new trends in seed crushing and oil refining

    Directory of Open Access Journals (Sweden)

    Kővári Katalin

    2004-11-01

    Full Text Available Oil processing was considered as slowly changing “traditional” industry but the recent decades’ developments and trends resulted in a lot of changes initiated by market, industry, environment protection and consumer needs. Driving force of the developments were centralization of the industry, more and more concerns on environmental impact, increased importance of food-feed safety, and last but not least research and development activity together with improved analytical capabilities. The presentation gives an overview on the results achieved on the field of the following areas: the criteria of applicability of physical refining of seed oils, solutions for proper degumming, the effect of seed pretreatment and crushing conditions on the crude oil quality, the importance and role of bleaching and active carbon treatment, the proper practice of deacidification/deodorization.

  14. Radiological assessment for bauxite mining and alumina refining.

    Science.gov (United States)

    O'Connor, Brian H; Donoghue, A Michael; Manning, Timothy J H; Chesson, Barry J

    2013-01-01

    Two international benchmarks assess whether the mining and processing of ores containing Naturally Occurring Radioactive Material (NORM) require management under radiological regulations set by local jurisdictions. First, the 1 Bq/g benchmark for radionuclide head of chain activity concentration determines whether materials may be excluded from radiological regulation. Second, processes may be exempted from radiological regulation where occupational above-background exposures for members of the workforce do not exceed 1 mSv/year. This is also the upper-limit of exposure prescribed for members of the public. Alcoa of Australia Limited (Alcoa) has undertaken radiological evaluations of the mining and processing of bauxite from the Darling Range of Western Australia since the 1980s. Short-term monitoring projects have demonstrated that above-background exposures for workers do not exceed 1 mSv/year. A whole-of-year evaluation of above-background, occupational radiological doses for bauxite mining, alumina refining and residue operations was conducted during 2008/2009 as part of the Alcoa NORM Quality Assurance System (NQAS). The NQAS has been guided by publications from the International Commission on Radiological Protection (ICRP), the International Atomic Energy Agency (IAEA) and the Australian Radiation Protection and Nuclear Safety Agency (ARPANSA). The NQAS has been developed specifically in response to implementation of the Australian National Directory on Radiation Protection (NDRP). Positional monitoring was undertaken to increase the accuracy of natural background levels required for correction of occupational exposures. This is important in view of the small increments in exposure that occur in bauxite mining, alumina refining and residue operations relative to natural background. Positional monitoring was also undertaken to assess the potential for exposure in operating locations. Personal monitoring was undertaken to characterise exposures in Similar

  15. Constraint rescaling in refined algebraic quantisation: Momentum constraint

    International Nuclear Information System (INIS)

    Louko, Jorma; Martinez-Pascual, Eric

    2011-01-01

    We investigate refined algebraic quantisation within a family of classically equivalent constrained Hamiltonian systems that are related to each other by rescaling a momentum-type constraint. The quantum constraint is implemented by a rigging map that is motivated by group averaging but has a resolution finer than what can be peeled off from the formally divergent contributions to the averaging integral. Three cases emerge, depending on the asymptotics of the rescaling function: (i) quantisation is equivalent to that with identity scaling; (ii) quantisation fails, owing to nonexistence of self-adjoint extensions of the constraint operator; (iii) a quantisation ambiguity arises from the self-adjoint extension of the constraint operator, and the resolution of this purely quantum mechanical ambiguity determines the superselection structure of the physical Hilbert space. Prospects of generalising the analysis to systems with several constraints are discussed.

  16. Processing Government Data: ZIP Codes, Python, and OpenRefine

    Directory of Open Access Journals (Sweden)

    Frank Donnelly

    2014-07-01

    Full Text Available While there is a vast amount of useful US government data on the web, some of it is in a raw state that is not readily accessible to the average user. Data librarians can improve accessibility and usability for their patrons by processing data to create subsets of local interest and by appending geographic identifiers to help users select and aggregate data. This case study illustrates how census geography crosswalks, Python, and OpenRefine were used to create spreadsheets of non-profit organizations in New York City from the IRS Tax-Exempt Organization Masterfile. This paper illustrates the utility of Python for data librarians and should be particularly insightful for those who work with address-based data.

  17. Refining the structure and content of clinical genomic reports.

    Science.gov (United States)

    Dorschner, Michael O; Amendola, Laura M; Shirts, Brian H; Kiedrowski, Lesli; Salama, Joseph; Gordon, Adam S; Fullerton, Stephanie M; Tarczy-Hornoch, Peter; Byers, Peter H; Jarvik, Gail P

    2014-03-01

    To effectively articulate the results of exome and genome sequencing we refined the structure and content of molecular test reports. To communicate results of a randomized control trial aimed at the evaluation of exome sequencing for clinical medicine, we developed a structured narrative report. With feedback from genetics and non-genetics professionals, we developed separate indication-specific and incidental findings reports. Standard test report elements were supplemented with research study-specific language, which highlighted the limitations of exome sequencing and provided detailed, structured results, and interpretations. The report format we developed to communicate research results can easily be transformed for clinical use by removal of research-specific statements and disclaimers. The development of clinical reports for exome sequencing has shown that accurate and open communication between the clinician and laboratory is ideally an ongoing process to address the increasing complexity of molecular genetic testing. © 2014 Wiley Periodicals, Inc.

  18. A Parametric Counterexample Refinement Approach for Robust Timed Specifications

    Directory of Open Access Journals (Sweden)

    Louis-Marie Traonouez

    2012-07-01

    Full Text Available Robustness analyzes the impact of small perturbations in the semantics of a model. This allows to model hardware imprecision and therefore it has been applied to determine implementability of timed automata. In a recent paper, we extend this problem to a specification theory for real-timed systems based on timed input/output automata, that are interpreted as two-player games. We propose a construction that allows to synthesize an implementation of a specification that is robust under a given timed perturbation, and we study the impact of these perturbations when composing different specifications. To complete this work we present a technique that evaluates the greatest admissible perturbation. It consists in an iterative process that extracts a spoiling strategy when a game is lost, and through a parametric analysis refines the admissible values for the perturbation. We demonstrate this approach with a prototype implementation.

  19. Refining the Tungusk meteorite trajectory from the testimony of eyewitnesses

    Science.gov (United States)

    Epiktetova, L. E.

    The Tungusk meteorite trajectory is refined using the testimony of many eyewitnesses who lived on the territory surrounding the area of the Tungusk meteorite explosion and described acoustic phenomena connected with the explosion. It is concluded that the horizontal projection of the Tungusk meteorite trajectory is within the range of the azimuths from the epicenter at 102-103 deg, at a distance of 300-500 km from the epicenter. It was also deduced from the eyewitnesses' testimony that, in the last section of the trajectory, its horizontal projection was shifted to the west and its vertical projection became steeper. As a result, the trajectory of the Tungusk meteorite cannot be described by a single value of the azimuth and a single value of the tilt angle from the epicenter.

  20. Characterization and process development for the selective removal of Sn, Sb, and As from anode slime obtained from electrolytic copper refining

    Directory of Open Access Journals (Sweden)

    Steinlechner S.

    2018-01-01

    Full Text Available The aim of this work was to develop a process for the removal of Sn, Sb and As from anode slime out of copper refinery to disburden a subsequent pyrometallurgical processing for precious metals refinement. For this reason, a detailed literature survey was conducted, followed by a characterization to find the present compounds/alloys and their morphology. A newly developed process concept for the separate extraction of the afore mentioned three target metals was developed and verified by leaching experiments, combined with thermodynamic calculations on their behavior under varying conditions. In this context, the influence of leaching temperature, alkalinity of leaching solution, and solid-liquid ration were evaluated on the extraction yields of Sn, As, and Sb, as well as how to exploit these findings to obtain separate streams enriched in the respective metals.