Selective chelation-supercritical fluid extraction of metal ions from waste materials

International Nuclear Information System (INIS)

Wai, C.N.; Laintz, K.E.; Yonker, C.R.

1993-01-01

The removal of toxic organics, metals, and radioisotopes from solids or liquids is a major concern in the treatment of industrial and nuclear wastes. For this reason, developing methods for selective separation of toxic metals and radioactive materials from solutions of complex matrix is an important problem in environmental research. Recent developments indicate supercritical fluids are good solvents for organic compounds. Many gases become supercritical fluids under moderate temperatures and pressures. For example, the critical temperature and pressure of carbon dioxide are 31 degrees C and 73 atm, respectively. The high diffusivity, low viscosity, and T-P dependence of solvent strength are some attractive properties of supercritical fluid extraction (SFE). Since CO 2 offers the additional benefits of stability and non-toxicity, the SFE technique avoids generation of organic liquid waste and exposure of personnel to toxic solvents. While direct extraction of metal ions by supercritical fluids is highly inefficient, these ions when complexed with organic ligands become quite soluble in supercritical fluids. Specific ligands can be used to achieve selective extraction of metal ions in this process. After SFE, the fluid phase can be depressurized for precipitation of the metal chelates and recycled. The ligand can also be regenerated for repeated use. The success of this selective chelation-supercritical fluid extraction (SC-SFE) process depends on a number of factors including the efficiencies of the selective chelating agents, solubilities of metal chelates in supercritical fluids, rate of extraction, ease of regeneration of the ligands, etc. In this report, the authors present recent results on the studies of the solubilities of metal chelates in supercritical CO 2 , experimental ions from aqueous solution, and the development of selective chelating agents (ionizable crown ethers) for the extraction of lanthanides and actinides

Crystal field in rare-earth metals and intermetallic compounds

International Nuclear Information System (INIS)

Ray, D.K.

1978-01-01

Reasons for the success of the crystal-field model for the rare-earth metals and intermetallic compounds are discussed. A review of some of the available experimental results is made with emphasis on cubic intermetallic compounds. Various sources of the origin of the crystal field in these metals are discussed in the background of the recent APW picture of the conduction electrons. The importance of the non-spherical part of the muffin-tin potential on the single-ion anisotropy is stressed. (author)

Studies about interaction of hydrogen isotopes with metals and intermetallic compounds

International Nuclear Information System (INIS)

Vasut, F.; Anisoara, P.; Zamfirache, M.

2003-01-01

Hydrogen is a non-toxic but highly inflammable gas. Compared to other inflammable gases, its range of inflammability in air is much broader (4-74.5%) but it also vaporizes much more easily. Handling of hydrogen in form of hydrides enhances safety. The interaction of hydrogen with metals and intermetallic compounds is a major field within physical chemistry. Using hydride-forming metals and intermetallic compounds, for example, recovery, purification and storage of heavy isotopes in tritium containing system can solve many problems arising in the nuclear-fuel cycle. The paper presents the thermodynamics and the kinetics between hydrogen and metal or intermetallic compounds. (author)

Efficient and Selective Reduction of Aromatic Nitro Compounds to Aromatic Amines by NbCl{sub 5}/Indium System

Energy Technology Data Exchange (ETDEWEB)

Yoo, Byung Woo; Kim, Duckil; Kim, Hyung Min; Kang, Sung Ho [Korea Univ., Seoul (Korea, Republic of)

2012-09-15

Aromatic amines find applicability in diverse fields including dyes, pharmaceuticals, agrochemicals, and photographic materials. To date, there are a variety of methods, which can be used to convert aromatic nitro compounds to their corresponding amines. Some of them include Cp{sub 2}TiCl{sub 2}/In, Al/NH{sub 4}Cl, (NH{sub 4}){sub 2}SO{sub 4}/NaBH{sub 4}, NiCl{sub 2}6H{sub 2}O/In, HI, Sm/I{sub 2}, In/NH{sub 4}Cl, B{sub 4}H{sub 10}/Pd/C, Co{sub 2}(CO){sub 8}/H{sub 2}O and In/HCl. However, most methods still lack the desired chemo-selectivity when other reducible functional groups are present in the nitroarene and often require long reaction times, or harsh reaction conditions. Consequently, efficient and selective methods for the reduction of aromatic nitro compounds continue to be developed. It has been reported that NbCl{sub 5}/Zn system is used as a reagent for reducing sulfoxides, epoxides, and amine N-oxides.12 Because of the close resemblance of indium to zinc in several respects, including first ionization potential, we considered that NbCl{sub 5}/In system can be an efficient reducing agent for the conversion of aromatic nitro compounds to the corresponding amines. Recently, indium metal has attracted much attention for its unique properties such as low toxicity and high stability in water and air compared with other metals. In continuation of our interest in exploring the utility of metal-metal salt system in organic synthesis, we would like to report an efficient and chemo-selective method for the reduction of various aromatic nitro compounds to the corresponding amines by treatment with NbCl{sub 5}/In system (eq. 1). The new reduction system was generated by the addition of indium powder to a stirred solution of niobium(V) chloride in THF under sonication. The generation of low-valent niobium species was examined at room temperature with an excess of indium metal. The observations suggest that this procedure can be applied for the chemo-selective

Metal organic frameworks for removal of compounds from a fluid

KAUST Repository

Eddaoudi, Mohamed

2016-03-03

Embodiments provide a method of compound removal from a fluid. The method includes contacting one or more metal organic framework (MOF) compositions with a fluid and sorbing one or more compounds, such as CO2, H2S and condensable hydrocarbons. One or more of CO2, H2S and condensable hydrocarbons can be sorbed simultaneously or in series. The metal organic framework can be an M-soc-MOF.

Metal organic frameworks for removal of compounds from a fluid

KAUST Repository

Eddaoudi, Mohamed; Belmabkhout, Youssef

2016-01-01

Embodiments provide a method of compound removal from a fluid. The method includes contacting one or more metal organic framework (MOF) compositions with a fluid and sorbing one or more compounds, such as CO2, H2S and condensable hydrocarbons. One or more of CO2, H2S and condensable hydrocarbons can be sorbed simultaneously or in series. The metal organic framework can be an M-soc-MOF.

Hydrolytic stability of heavy metal compounds in fly ash of a heat power plant

International Nuclear Information System (INIS)

Suslova, E.P.; Pertsikov, I.Z.

1991-01-01

Ash and slag from solid fuels are utilized widely in building materials and road surfaces, and in agriculture for soil acidulation. For all these uses it is important to know the amount and form of heavy metal compounds contained in ash and their likely behavior when ash and slag wastes are utilized. Studying the behavior of heavy metals in ash residues at contact with water media is important also because, for most trace elements, the authors lack experimental data that would enable us to predict their behavior after prolonged storage and industrial utilization. The present paper describes a study of lixiviation (at various pH in static conditions) of heavy metals form fly ash obtained by burning Azeisk coal. Homogenized ash selected from electric filter sections 1-4 was used, which has the following composition (%): SiO 2 59.8; Al 2 O 3 ; Fe 23 O 3 7.1; CaO 4.1; MgO 1.3; other 2.8. In a neutral medium, Ni, Cu, Zn, Pb, and Mn lixiviation was slight, amounting to 0.01-0.4%. During coal combustion, these elements apparently form compounds that are slightly soluble in water, although it is also possible that ash retains high adsorptivity for heavy metals. As a result, in these conditions the reverse process of sorption of heavy metals from the solution by fly ash is also possible, which would reduce the heavy metal concentration in the solution

Mutagenesis of metal compounds in bacteria

Energy Technology Data Exchange (ETDEWEB)

Nishioka, H

1974-01-01

The mutagenic activity of 41 metal compounds was examined by applying the Rec-assay method with Bacillus subtilis H17 (rec/sup +/) and M45 (rec/sup -/) strains. Among these compounds, Na/sub 2/HAsO/sub 4/, CdCl/sub 2/, K/sub 2/CrO/sub 4/, K/sub 2/Cr/sub 2/O/sub 7/, CH/sub 3/HgCl, C/sub 2/H/sub 5/HgCl, CH/sub 3/COOHgC/sub 6/H/sub 5/, MnCl/sub 2/, MnNO/sub 3/, MnSO/sub 4/, Mn(CH/sub 3/COO)/sub 2/, (NH/sub 4/)/sub 2/MoO/sub 4/ and KMoO/sub 4/ showed positive results. The reactions of K/sub 2/Cr/sub 2/O/sub 7/ and (NH/sub 4/)/sub 2/MoO/sub 4/ were especially strong in the assay. Therefore, mutation induction to reversion (try/sup +/) and streptomycin resistance (SM/sup r/) of E. coli B/r WP2 try/sup -/ (hcl/sup +/ and hcr/sup -/) by the two compounds were examined by the following two experimental procedures. Stationary phase bacteria were exposed to the compounds at high concentrations (6.9 x 10/sup -3/ approx. 3.44 x 10/sup -2/M) in M9 buffer for 15 min at 37/sup -/ with shaking. After incubation at 37/sup 0/ for 48 h visible colonies on the plates were scored. Bacteria in M9 buffer were plated in media supplemented with low concentrations (1.7 x 10/sup -5/ approx. 3.4 x 10/sup -5/M) of the compounds. K/sub 2/Cr/sub 2/O/sub 7/ and (NH/sub 4/)/sub 2/MoO/sub 4/ increased the mutation rate of SM/sup r/ and try/sup +/ in both strains treated with either procedure. No marked differences in mutation rate were found between hcr/sup +/ and hcr/sup -/. After treatment with high concentrations of compounds one can imagine that a peroxidation state produced by these peroxides in the media might affect the killing and mutation induction. These results suggest the possibility that the mutagenesis of the metals relate to their atomic values, rather than the peroxidation state as far as these two compounds are concerned.

On the valence state of Yb and Ce in transition metal intermetallic compounds

International Nuclear Information System (INIS)

Boer, F.R. de; Dijkman, W.H.; Mattens, W.C.M.

1979-01-01

In the pure state Yb is a divalent metal, similar to Ca; in alloys it can become trivalent like the majority of the rare earth metals. Using a value of 38 kJ (mol Yb) -1 for the energy difference between divalent and trivalent Yb metal and using model calculations for the heat of formation of intermetallic compounds, the authors are able to account for the existing information on the valence state of Yb in transition metal compounds. A similar analysis of compounds of Ce with transition metals shows that a model in which the 4f electron is treated as a core electron, i.e. being absent in the tetravalent modification of Ce and present as a fully localized electron in trivalent Ce, does not apply. (Auth.)

Construction of three lanthanide metal-organic frameworks: Synthesis, structure, magnetic properties and highly selective sensing of metal ions

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiu-Mei, E-mail: zhangxiumeilb@126.com; Li, Peng; Gao, Wei; Liu, Feng; Liu, Jie-Ping

2016-12-15

Three lanthanide metal-organic frameworks (Ln-MOFs), [Ln(TZI)(H{sub 2}O){sub 4}]·3H{sub 2}O (Ln=Gd (1) and Tb (2) and Dy (3), H{sub 3}TZI=5-(1H-tetrazol-5-yl)isophthalic acid), have been synthesized under hydrothermal conditions. Single crystal X-ray diffraction reveals that 1–3 are isostructural and display a 1D double chain based on dinuclear motifs with (μ-COO){sub 2} double bridges. Magnetic studies indicate antiferromagnetic interactions in 1, ferromagnetic interactions in 2 and 3. Furthermore, compound 3 displays a slow relaxation behavior. Compound 2 exhibits intense characteristic green emission of Tb(III) ions in the solid state, which can be observed by the naked eye under UV light. Interestingly, 2 can selectively sense Pb{sup 2+} and Fe{sup 3+} ions through luminescence enhancement and quenching, respectively. The luminescence quenching mechanisms have been investigated in detail. The study on luminescence Ln-MOFs as a probe for sensing Pb{sup 2+} and Fe{sup 3+} ions is exceedingly rare example. - Graphical abstract: Three Ln-MOFs were successfully synthesized using a 5-(1H-tetrazol-5-yl)isophthalic acid ligand. They displays different magnetic behavior. Especially, the Dy(III) compound slow relaxation behavior. Interestingly, the Tb(III) compound can selectively sense Pb{sup 2+} and Fe{sup 3+} ions through luminescence enhancement and quenching, respectively. - Highlights: • Three Ln-MOFs with tetrazolate dicarboxylate ligand. • Dy(III) compound displays slow relaxation behavior. • The Tb(III) compound shows highly selective luminescence sensing of the Fe{sup 3+} and Pb{sup 2+} ions.

Metal complex catalysis in the synthesis of organoaluminium compounds

International Nuclear Information System (INIS)

Dzhemilev, Usein M; Ibragimov, Askhat G

2000-01-01

The published data on the synthesis of organoaluminium compounds involving metal complex catalysts are generalised and systematised. Hydro-, carbo- and cycloalumination reactions of alkenes, conjugated dienes and alkynes catalysed by Ti and Zr complexes are considered in detail. The use of organoaluminium reagents in organic synthesis and novel reactions involving these compounds are discussed. The bibliography includes 240 references.

Commodity profiles for selected metals

International Nuclear Information System (INIS)

Svoboda, O.; Wilson, B.M.

1985-01-01

This report describes the basic characteristics of 35 metals and gives the prices and production of these metals for the period 1979 to 1983/4. The description of each metal includes the ore grades and reserves, the major minerals in which the metal occurs, and the discovery, selected physical properties, sources, uses, substitutes, and effects on the environment of the metal. Graphs showing price and production cover the period 1950 to 1984, and possible future developments in these areas are forecast for each metal until the year 2000

Neutron scattering investigation of layer-bending modes in alkali-metal--graphite intercalation compounds

International Nuclear Information System (INIS)

Zabel, H.; Kamitakahara, W.A.; Nicklow, R.M.

1982-01-01

Phonon dispersion curves for low-frequency transverse modes propagating in the basal plane have been measured in the alkali-metal--graphite intercalation compounds KC 8 , CsC 8 , KC 24 , and RbC 24 by means of neutron spectroscopy. The acoustic branches show an almost quadratic dispersion relation at small q, characteristic of strongly layered materials. The optical branches of stage-1 compounds can be classified as either graphitelike branches showing dispersion, or as almost dispersionless alkali-metal-like modes. Macroscopic shear constants C 44 and layer-bending moduli have been obtained for the intercalation compounds by analyzing the data in terms of a simple semicontinuum model. In stage-2 compounds, a dramatic softening of the shear constant by about a factor of 8 compared with pure graphite has been observed. Low-temperature results on KC 24 indicate the opening of a frequency gap near the alkali-metal Brillouin-zone boundary, possibly due to the formation of the alkali-metal superstructure

Catalytic ozonation not relying on hydroxyl radical oxidation: A selective and competitive reaction process related to metal-carboxylate complexes

KAUST Repository

Zhang, Tao

2014-01-01

Catalytic ozonation following non-hydroxyl radical pathway is an important technique not only to degrade refractory carboxylic-containing organic compounds/matter but also to avoid catalyst deactivation caused by metal-carboxylate complexation. It is unknown whether this process is effective for all carboxylates or selective to special molecule structures. In this work, the selectivity was confirmed using O3/(CuO/CeO2) and six distinct ozone-resistant probe carboxylates (i.e., acetate, citrate, malonate, oxalate, pyruvate and succinate). Among these probe compounds, pyruvate, oxalate, and citrate were readily degraded following the rate order of oxalate>citrate>pyruvate, while the degradation of acetate, malonate, and succinate was not promoted. The selectivity was independent on carboxylate group number of the probe compounds and solution pH. Competitive degradation was observed for carboxylate mixtures following the preference order of citrate, oxalate, and finally pyruvate. The competitive degradation was ascribed to competitive adsorption on the catalyst surface. It was revealed that the catalytically degradable compounds formed bidentate chelating or bridging complexes with surface copper sites of the catalyst, i.e., the active sites. The catalytically undegradable carboxylates formed monodentate complexes with surface copper sites or just electrostatically adsorbed on the catalyst surface. The selectivity, relying on the structure of surface metal-carboxylate complex, should be considered in the design of catalytic ozonation process. © 2013 Elsevier B.V.

PEROXOTITANATE- AND MONOSODIUM METAL-TITANATE COMPOUNDS AS INHIBITORS OF BACTERIAL GROWTH

Energy Technology Data Exchange (ETDEWEB)

Hobbs, D.

2011-01-19

Sodium titanates are ion-exchange materials that effectively bind a variety of metal ions over a wide pH range. Sodium titanates alone have no known adverse biological effects but metal-exchanged titanates (or metal titanates) can deliver metal ions to mammalian cells to alter cell processes in vitro. In this work, we test a hypothesis that metal-titanate compounds inhibit bacterial growth; demonstration of this principle is one prerequisite to developing metal-based, titanate-delivered antibacterial agents. Focusing initially on oral diseases, we exposed five species of oral bacteria to titanates for 24 h, with or without loading of Au(III), Pd(II), Pt(II), and Pt(IV), and measuring bacterial growth in planktonic assays through increases in optical density. In each experiment, bacterial growth was compared with control cultures of titanates or bacteria alone. We observed no suppression of bacterial growth by the sodium titanates alone, but significant (p < 0.05, two-sided t-tests) suppression was observed with metal-titanate compounds, particularly Au(III)-titanates, but with other metal titanates as well. Growth inhibition ranged from 15 to 100% depending on the metal ion and bacterial species involved. Furthermore, in specific cases, the titanates inhibited bacterial growth 5- to 375-fold versus metal ions alone, suggesting that titanates enhanced metal-bacteria interactions. This work supports further development of metal titanates as a novel class of antibacterials.

Metal-chelating compounds produced by ectomycorrhizal fungi collected from pine plantations.

Science.gov (United States)

Machuca, A; Pereira, G; Aguiar, A; Milagres, A M F

2007-01-01

To investigate the in vitro production of metal-chelating compounds by ectomycorrhizal fungi collected from pine plantations in southern Chile. Scleroderma verrucosum, Suillus luteus and two isolates of Rhizopogon luteolus were grown in solid and liquid modified Melin-Norkans (MMN) media with and without iron addition and the production of iron-chelating compounds was determined by Chrome Azurol S (CAS) assay. The presence of hydroxamate and catecholate-type compounds and organic acids was also investigated in liquid medium. All isolates produced iron-chelating compounds as detected by CAS assay, and catecholates, hydroxamates as well as oxalic, citric and succinic acids were also detected in all fungal cultures. Scleroderma verrucosum produced the greatest amounts of catecholates and hydroxamates whereas the highest amounts of organic acids were detected in S. luteus. Nevertheless, the highest catecholate, hydroxamate and organic acid concentrations did not correlate with the highest CAS reaction which was observed in R. luteolus (Yum isolate). Ectomycorrhizal fungi produced a variety of metal-chelating compounds when grown in liquid MMN medium. However, the addition of iron to all fungi cultures reduced the CAS reaction, hydroxamate and organic acid concentrations. Catecholate production was affected differently by iron, depending on the fungal isolate. The ectomycorrhizal fungi described in this study have never been reported to produce metal-chelating compound production. Moreover, apart from some wood-rotting fungi, this is the first evidence of the presence of catecholates in R. luteolus, S. luteus and S. verrucosum cultures.

Sythesis of rare earth metal - GIC graphite intercalation compound in molten chloride system

International Nuclear Information System (INIS)

Ito, Masafumi; Hagiwara, Rika; Ito, Yasuhiko

1994-01-01

Graphite intercalation compounds of ytterbium and neodymium have been prepared by interacting graphite and metals in molten chlorides. These rare earth metals can be suspended in molten chlorides in the presence of trichlorides via disproportionation reaction RE(0) + RE(III) = 2RE(II) at lower than 300 degC. Carbides-free compounds are obtained in these systems. (author)

Designer ligands: The search for metal ion selectivity

Directory of Open Access Journals (Sweden)

Perry T. Kaye

2011-03-01

Full Text Available The paper reviews research conducted at Rhodes University towards the development of metal-selective ligands. The research has focused on the rational design, synthesis and evaluation of novel ligands for use in the formation of copper complexes as biomimetic models of the metalloenzyme, tyrosinase, and for the selective extraction of silver, nickel and platinum group metal ions in the presence of contaminating metal ions. Attention has also been given to the development of efficient, metal-selective molecular imprinted polymers.

PREPARATION OF A POLYMER ARTICLE FOR SELECTIVE METALLIZATION

DEFF Research Database (Denmark)

2008-01-01

The present invention relates to the field of selective metallization, and in particular to preparing a polymer article for selective metallization by submerging the article in a first liquid, and while submergedirradiate the article by a laser beam the area of the article on which the metal...... is to be deposited. An activation step, prior to the selective metallization, comprises submerging the article in an activation liquid for depositing seedparticles in the selected area. The irradiation of the selected area is proportionate so as to cause a temporary meltingof the polymer in the surface...... of the selected area of the polymer article. The invention is advantageous in that the preparation may be performed with a relatively high scan rate across the polymer article, and in that a quite limited use of toxic chemicals....

Coordination compounds of metals with imidazoles and benzimidazoles

International Nuclear Information System (INIS)

Novikova, G.A.; Molodkin, A.K.; Kukalenko, S.S.

1988-01-01

Methods of preparation, composition and structure of UO 2 2+ , Th 4+ , Mo 3+ , Cd 2+ , Ln 3+ metal ion complexes with imidazoles and benzimidazoles are considered in reviews of native and foreign literature of up to 1985. Complexes are customarily prepared by direct interaction of ligands with inorganic salts in different organic solvents. Complex composition is defined by the nature of complexing metal and inorganic salt anion, ligand volume and basicity, as well as solvent characteristics. Effect of R substituent in imidazole and benzimidazole side chain on composition of coordination compounds is considered

Proficiency test for heavy metals in compound feed

NARCIS (Netherlands)

Pereboom, D.P.K.H.; Elbers, I.J.W.; Jong, de J.; Lee, van der M.K.; Nijs, de W.C.M.

2016-01-01

The here described proficiency test for heavy metals in compound feed was organised by RIKILT, Wageningen UR in accordance with ISO 17043. RIKILT Wageningen UR has an ISO/IEC 17043 accreditation for proficiency tests of residues in products of animal origin. However, this specific test is not part

Synthesis of graphite intercalation compound of group VI metals and uranium hexafluorides

International Nuclear Information System (INIS)

Fukui, Toshihiro; Hagiwara, Rika; Ema, Keiko; Ito, Yasuhiko

1993-01-01

Systematic investigations were made on the synthesis of graphite intercalation compounds of group VI transition metals (W and Mo) and uranium hexafluorides. The reactions were performed by interacting liquid or gaseous metal hexafluorides with or without elemental fluorine at ambient temperature. The degree of intercalation of these metal fluorides depends on the formation enthalpy of fluorometallate anion from the original metal hexafluoride, as has been found for other intercalation reactions of metal fluorides. (author)

Heavy-metal compounds in the environment of the Zagorsk pumped-storage station region

International Nuclear Information System (INIS)

Dmitrieva, I.L.; Zagoskin, V.A.; Boldenkov, V.S.; Brusilovskii, O.V.

1993-01-01

The Zagorsk pumped-storage station (ZPSS) is being constructed in a rather developed area. Pollution of the environment by compounds of metals is, in particular, a consequence. The tasks of this investigation included: the establishment of the main sources of pollution of terrestrial and aquatic ecosystems by metal compounds in the region of construction of the ZPSS; determination of the level of content of these substances in various components of the landscape; and evaluation of the effect of regulating the Kun'ya River on processes of migration and accumulation of heavy metals in aquatic ecosystems. In conformity with these tasks, a comprehensive geochemical study was performed in 1990-1991 of the drainage basin of the Kun'ya River, the results of which are presented here. Samples were collected of soil, forest litter, snow, bottom sediments, and surface waters. The investigation showed that the main sources of pollution of the aquatic environment in the ZPSS construction region by heavy-metal compounds were surface runoff from developed territories and insufficiently treated industrial wastewaters. 5 refs., 2 figs., 4 tabs

Method of making metal oxide ceramic powders by using a combustible amino acid compound

Science.gov (United States)

Pederson, Larry R.; Chick, Lawrence A.; Exarhos, Gregory J.

1992-01-01

This invention is directed to the formation of homogeneous, aqueous precursor mixtures of at least one substantially soluble metal salt and a substantially soluble, combustible co-reactant compound, typically an amino acid. This produces, upon evaporation, a substantially homogeneous intermediate material having a total solids level which would support combustion. The homogeneous intermediate material essentially comprises highly dispersed or solvated metal constituents and the co-reactant compound. The intermediate material is quite flammable. A metal oxide powder results on ignition of the intermediate product which combusts same to produce the product powder.

Process for removing heavy metal compounds from heavy crude oil

Science.gov (United States)

Cha, Chang Y.; Boysen, John E.; Branthaver, Jan F.

1991-01-01

A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

Characterization of selected volatile organic compounds, polycyclic aromatic hydrocarbons and carbonyl compounds at a roadside monitoring station

Science.gov (United States)

Ho, K. F.; Lee, S. C.; Chiu, Gloria M. Y.

Volatile organic compounds (VOCs), PAHs and carbonyl compounds are the major toxic components in Hong Kong. Emissions from motor vehicles have been one of the primary pollution sources in the metropolitan areas throughout Hong Kong for a long time. A 1-yr monitoring program for VOCs, PAHs and carbonyl compounds had been performed at a roadside urban station at Hong Kong Polytechnic University in order to determine the variations and correlations of each selected species (VOCs, PAHs and carbonyl compounds). This study is aimed to analyze toxic volatile organic compounds (benzene, toluene, ethylbenzene and xylene), two carbonyl compounds (formaldehyde, acetaldehyde), and selective polycyclic aromatic hydrocarbons. The monitoring program started from 16 April 1999 to 30 March 2000. Ambient VOC concentrations, many of which originate from the same sources as particulate PAHs and carbonyls compounds, show significant quantities of benzene, toluene and xylenes. Correlations and multivariate analysis of selected gaseous and particulate phase organic pollutants were performed. Source identification by principle component analysis and hierarchical cluster analysis allowed the identification of four sources (factors) for the roadside monitoring station. Factor 1 represents the effect of diesel vehicle exhaust. Factor 2 shows the contribution of aromatic compounds. Factor 3 explains photochemical products—formaldehyde and acetaldehyde. Factor 4 explains the effect of gasoline vehicle exhaust.

Distribution of uranium and some selected trace metals in human scalp hair from Balkans.

Science.gov (United States)

Zunic, Z S; Tokonami, S; Mishra, S; Arae, H; Kritsananuwat, R; Sahoo, S K

2012-11-01

The possible consequences of the use of depleted uranium (DU) used in Balkan conflicts in 1995 and 1999 for the people and the environment of this reason need attention. The heavy metal content in human hair may serve as a good indicator of dietary, environmental and occupational exposures to the metal compounds. The present work summarises the distribution of uranium and some selected trace metals such as Mn, Ni, Cu, Zn, Sr, Cd and Cs in the scalp hair of inhabitants from Balkans exposed to DU directly and indirectly, i.e. Han Pijesak, Bratoselce and Gornja Stubla areas. Except U and Cs, all other metals were compared with the worldwide reported values of occupationally unexposed persons. Uranium concentrations show a wide variation ranging from 0.9 ± 0.05 to 449 ± 12 µg kg(-1). Although hair samples were collected from Balkan conflict zones, uranium isotopic measurement ((235)U/(238)U) shows a natural origin rather than DU.

Organometallic compounds of the lanthanides, actinides and early transition metals

Energy Technology Data Exchange (ETDEWEB)

Cardin, D J [Trinity Coll., Dublin (Ireland); Cotton, S A [Stanground School, Peterborough (UK); Green, M [Bristol Univ. (UK); Labinger, J A [Atlantic Richfield Co., Los Angeles, CA (USA); eds.

1985-01-01

This book provides a reference compilation of physical and biographical data on over 1500 of the most important and useful organometallic compounds of the lanthanides, actinides and early transition metals representing 38 different elements. The compounds are listed in molecular formula order in a series of entries in dictionary format. Details of structure, physical and chemical properties, reactions and key references are clearly set out. All the data is fully indexed and a structural index is provided.

Impedance study of tea with added taste compounds using conducting polymer and metal electrodes.

Science.gov (United States)

Dhiman, Mopsy; Kapur, Pawan; Ganguli, Abhijit; Singla, Madan Lal

2012-09-01

In this study the sensing capabilities of a combination of metals and conducting polymer sensing/working electrodes for tea liquor prepared by addition of different compounds using an impedance mode in frequency range 1 Hz-100 KHz at 0.1 V potential has been carried out. Classification of six different tea liquor samples made by dissolving various compounds (black tea liquor + raw milk from milkman), (black tea liquor + sweetened clove syrup), (black tea liquor + sweetened ginger syrup), (black tea liquor + sweetened cardamom syrup), (black tea liquor + sweet chocolate syrup) and (black tea liquor + vanilla flavoured milk without sugar) using six different working electrodes in a multi electrode setup has been studied using impedance and further its PCA has been carried out. Working electrodes of Platinum (Pt), Gold (Au), Silver (Ag), Glassy Carbon (GC) and conducting polymer electrodes of Polyaniline (PANI) and Polypyrrole (PPY) grown on an ITO surface potentiostatically have been deployed in a three electrode set up. The impedance response of these tea liquor samples using number of working electrodes shows a decrease in the real and imaginary impedance values presented on nyquist plots depending upon the nature of the electrode and amount of dissolved salts present in compounds added to tea liquor/solution. The different sensing surfaces allowed a high cross-selectivity in response to the same analyte. From Principal Component Analysis (PCA) plots it was possible to classify tea liquor in 3-4 classes using conducting polymer electrodes; however tea liquors were well separated from the PCA plots employing the impedance data of both conducting polymer and metal electrodes.

The Impact of Template Types on Polyeugenol to the Adsorption Selectivity of Ionic Imprinted Polymer (IIP) Fe Metal Ion

Science.gov (United States)

Djunaidi, M. C.; Haris, A.; Pardoyo; Rosdiana, K.

2018-04-01

The synthesis of IIP was carried out by variation of Fe(III) ion templates from Fe(NO3)3, K3[Fe(CN)6] and NH4Fe(SO4)2 compounds which then tested IIP selectivity to the Fe metal ions through adsorption process. Ionic Imprinted Polymer (IIP) is a method of printing metal ions bound in a polymer, subsequently released from the polymer matrix to produce a suitable imprint for the target ion. The purposes of this study were to produce IIP from Fe(NO3)3, K3[Fe(CN)6] and NH4Fe(SO4)2 templates, to know the effect of templates on adsorption selectivity of IIP involving imprint cavity, and to know the impact of metal competitor on the selectivity adsorption of IIP to the Fe metals. The results obtained showed that IIP synthesized by variations of Fe(NO3)3, K3[Fe(CN)6] and NH4Fe(SO4)2 templates were successfully synthesized. The adsorption selectivity of Fe (III) metal ion in the Fe(NO3)3 template was greater than that of in the K3[Fe(CN)6] and NH4Fe(SO4)2 templates. The adsorption selectivity of Fe was greater on Fe-Cr compared to on Fe-Cd and Fe-Pb.

New spintronic superlattices composed of half-metallic compounds with zinc-blende structure

International Nuclear Information System (INIS)

Fong, C Y; Qian, M C

2004-01-01

The successful growth of zinc-blende half-metallic compounds, namely CrAs and CrSb, in thin film forms offers a new direction to search for novel spintronic materials. By using a well documented first-principles algorithm, the VASP code, we predict the electronic and magnetic properties of superlattices made of these exciting half-metallic materials. Not only are the superlattices constructed with two of the half-metallic compounds (CrAs/MnAs) but also they are modelled to combine with both a III-V (GaAs-MnAs/CrAs/GaAs) and a IV-IV (MnC/SiC) semiconductor. We investigate variable thicknesses for the combinations. For every case, we find the equilibrium lattice constant as well as the lattice constant at which the superlattice exhibits the half-metallic properties. For CrAs/MnAs, the half-metallic properties are presented and the magnetic moments are shown to be the sum of the moments for MnAs and CrAs. The half-metallic properties of GaAs-MnAs/CrAs/GaAs are found to be crucially dependent on the completion of the d-p hybridization. The magnetic properties of MnC/SiC are discussed with respect to the properties of MnC

Separation of polar compounds using a flexible metal-organic framework

NARCIS (Netherlands)

Motkuri, R.K.; Thallapally, P.K.; Annapureddy, H.V.R.; Dang, L.X.; Krishna, R.; Nune, S.K.; Fernandez, C.A.; Liu, J.; McGrail, B.P.

2015-01-01

A flexible metal-organic framework constructed from a flexible linker is shown to possess the capability of separating mixtures of polar compounds (propanol isomers) by exploiting the differences in the saturation capacities of the constituents. Transient breakthrough simulations show that these

Two new POMOF compounds constructed from polyoxoanions, metals and organic ligands

Science.gov (United States)

Xiao, Li-Na; Zhang, Hao; Zhang, Ting-Ting; Zhang, Xiao; Cui, Xiao-Bing

2018-03-01

Two new POMOF compounds, namely [PMo12V2O42][Cu3(4,4'-bpy)3]·(DABCO) (1) and [PMo10V4O42][Cu2(4,4'-bpy)2][Cu(phen)2]2 (2) (DABCO = triethylenediamine, bpy = bipyridine, phen = 1,10-phenanthroline)), have been synthesized and characterized by IR, UV-Vis, XRD, elemental analysis and X-ray diffraction analysis. Crystal structure analyses reveal that compounds 1 and 2 exhibit novel 2-D layered framework structures constructed from bi-capped Keggin molybdenum-vanadium polyoxoanions, metals and organic ligands, respectively. The main difference of the two compounds is that compound 2 contains both Cu2+ and Cu+ complexes. In addition, we also investigate the catalytic properties of the two compounds, both compound 1 and 2 are excellent catalysts for the epoxidation of styrene.

The synthesis and properties of some organometallic compounds containing group IV (Ge, Sn)-group II (Zn, Cd) metal---metal bonds

NARCIS (Netherlands)

Des Tombe, F.J.A.; Kerk, G.J.M. van der; Creemers, H.M.J.C.; Carey, N.A.D.; Noltes, J.G.

1972-01-01

The reactions of triphenylgermane and triphenyltin hydride with coordinatively saturated organozinc or organocadmium compounds give organometallic complexes containing Group IV (Ge, Sn)-Group II(Zn, Cd) metal---metal bonds. The 2,2′-bipyridine complexes show solvent-dependent charge-transfer

Process for production of a borohydride compound

Science.gov (United States)

Allen, Nathan Tait; Butterick, III, Robert; Chin, Arthur Achhing; Millar, Dean Michael; Molzahn, David Craig

2014-08-19

A process for production of a borohydride compound M(BH.sub.4).sub.y. The process has three steps. The first step combines a compound of formula (R.sup.1O).sub.yM with aluminum, hydrogen and a metallic catalyst containing at least one metal selected from the group consisting of titanium, zirconium, hafnium, niobium, vanadium, tantalum and iron to produce a compound of formula M(AlH.sub.3OR.sup.1).sub.y, wherein R.sup.1 is phenyl or phenyl substituted by at least one alkyl or alkoxy group; M is an alkali metal, Be or Mg; and y is one or two; wherein the catalyst is present at a level of at least 200 ppm based on weight of aluminum. The second step combines the compound of formula M(AlH.sub.3OR.sup.1).sub.y with a borate, boroxine or borazine compound to produce M(BH.sub.4).sub.y and a byproduct mixture containing alkali metal and aluminum aryloxides. The third step separates M(BH.sub.4).sub.y from the byproduct mixture.

Effect of some metal-containing compounds and fertilizers on ...

African Journals Online (AJOL)

USER

2010-06-28

Jun 28, 2010 ... grown on potato dextrose agar (PDA, BDH Ltd, UK 39 g/l) medium, maintained on PDA medium and stored at 4°C for further use. In this experiment, the mycelia growth capability of the Trichoderma isolates against some metal-containing compounds and fertilizers, consist of MgSO4.7H2O (containing ...

Stability and electronic structure of Zr-based ternary metallic glasses and relevant compounds

International Nuclear Information System (INIS)

Hasegawa, M.; Soda, K.; Sato, H.; Suzuki, T.; Taketomi, T.; Takeuchi, T.; Kato, H.; Mizutani, U.

2007-01-01

The electronic structure of the Zr-based metallic glasses has been investigated by theoretical and experimental approaches. One approach is band calculations of the Zr 2 Ni (Zr 66.7 Ni 33.3 ) compound to investigate the electronic structure of the Zr 66.7 Ni 33.3 metallic glass (ΔT x = 0 K) of which the local atomic structure is similar to that of the Zr 2 Ni compound. The other is photoemission spectroscopy of the Zr 50 Cu 35 Al 15 bulk metallic glass (BMG) (ΔT x = 69 K). Here ΔT x = T x - T g where T x and T g are crystallization and glass transition temperature, respectively. Both results and previous ones on the Zr 55 Cu 30 Ni 5 Al 10 BMG indicate that there is a pseudogap at the Fermi level in the electronic structure of these Zr-based metallic glasses, independent of the value of the ΔT x . This implies that the pseudogap at the Fermi level is one of the factors that stabilize the glass phase of Zr-based metallic glasses

Mechanism of selective ion flotation. 1. Selective flotation of transition metal cations

International Nuclear Information System (INIS)

Walkowiak, W.

1991-01-01

An experimental investigation is presented of the batch ion flotation of the transition metal cations Cr 3+ , Fe 3+ , Mn 2+ , Co 2+ , Zn 2+ , Ag + , Cd 2+ , and In 3+ from acidic aqueous solutions with sodium dodecylsulfonate and sodium dodecylbenzenesulfonate as anionic surfactants. The selectivity sequences Mn 2+ 2+ 2+ 3+ 3+ and Ag + 2+ 3+ are established, both from data for single and multi-ion metal cations solutions, where sublate was not formed in the bulk solution. Good agreement between the selectivity sequences and the values of ionic potential of metal cations was found. An experimental investigation was also performed on the solubility of sublates. The sublates solubility values are discussed in terms of ionic potentials of metal cations as well as of the surfactant size

Selective metal-vapor deposition on solvent evaporated polymer surfaces

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, Koji; Tsujioka, Tsuyoshi, E-mail: tsujioka@cc.osaka-kyoiku.ac.jp

2015-12-31

We report a selective metal-vapor deposition phenomenon based on solvent printing and evaporation on polymer surfaces and propose a method to prepare fine metal patterns using maskless vacuum deposition. Evaporation of the solvent molecules from the surface caused large free volumes between surface polymer chains and resulted in high mobility of the chains, enhancing metal-vapor atom desorption from the surface. This phenomenon was applied to prepare metal patterns on the polymer surface using solvent printing and maskless metal vacuum deposition. Metal patterns with high resolution of micron scale were obtained for various metal species and semiconductor polymer substrates including poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] and poly(3-hexylthiophene-2,5-diyl). - Highlights: • Selective metal-vapor deposition using solvent evaporation on polymer was attained. • Metal patterns with high resolution were obtained for various metal species. • This method can be applied to achieve fine metal-electrodes for polymer electronics.

50 years of superbases made from organolithium compounds and heavier alkali metal alkoxides

Czech Academy of Sciences Publication Activity Database

Lochmann, Lubomír; Janata, Miroslav

2014-01-01

Roč. 12, č. 5 (2014), s. 537-548 ISSN 1895-1066 R&D Projects: GA ČR GAP106/12/0844 Institutional support: RVO:61389013 Keywords : superbases * heavier alkali metal compounds * lithium -heavier alkali metal interchange Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.329, year: 2013

Vacuum tight sodium resistant compound between ThO2 ceramic and metal

International Nuclear Information System (INIS)

Reetz, T.

A method for evaluating the mechanical tensions for metal/ ceramic joinings was applied to the selection of metal components for a highly vacuum tight, sodium-resistant metal/ThO 2 ceramic solder joining. The metal component selected was the iron--nickel alloy Dilasil which is joined to the ceramic using a nickel-based solder. The wetting of the cearamic could be carried out using the titanium hydride technique or after the formation of a W-cerium layer on the surface of this ceramic. (U.S.)

High surface area graphene-supported metal chalcogenide assembly

Science.gov (United States)

Worsley, Marcus A.; Kuntz, Joshua D.; Orme, Christine A.

2017-04-25

Disclosed here is a method for hydrocarbon conversion, comprising contacting at least one graphene-supported assembly with at least one hydrocarbon feedstock, wherein the graphene-supported assembly comprises (i) a three-dimensional network of graphene sheets crosslinked by covalent carbon bonds and (ii) at least one metal chalcogenide compound disposed on the graphene sheets, wherein the chalcogen of the metal chalcogenide compound is selected from S, Se and Te, and wherein the metal chalcogenide compound accounts for at least 20 wt. % of the graphene-supported assembly.

Laser deposition rates of thin films of selected metals and alloys

DEFF Research Database (Denmark)

Cazzaniga, Andrea Carlo; Canulescu, Stela; Schou, Jørgen

Thin films of Cu, Zn and Sn as well as mixtures of these elements have been produced by Pulsed Laser Deposition (PLD). The deposition rate of single and multicomponent metallic targets was determined. The strength of PLD is that the stoichiometry of complex compounds, even of complicated alloys...... or metal oxides, can be preserved from target to film. We apply this technique to design films of a mixture of Cu, Zn and Sn, which are constituents of the chalcogenide CZTS, which has a composition close to Cu2ZnSnS4. This compound is expected to be an important candidate for absorbers in new solar cells...... for alloys of the different elements as well as compounds with S will be presented....

Radiolytic and photochemical reduction of carbon dioxide in solution catalyzed by transition metal complexes with some selected macrocycles

International Nuclear Information System (INIS)

Grodkowski, J.

2004-01-01

The main goal of the work presented in this report is an explanation of the mechanism of carbon dioxide (CO 2 ) reduction catalyzed by transition metal complexes with some selected macrocycles. The catalytic function of two electron exchange centers in the reduction of CO 2 , an inner metal and a macrocycle ring, was defined. Catalytic effects of rhodium, iron and cobalt porphyrins, cobalt and iron phthalocyanines and corroles as well as cobalt corrins have been investigated. CO 2 reduction by iron ions without presence of macrocycles and also in presence of copper compounds in aqueous solutions have been studied as well

Thermal behaviour of nicotinic acid, sodium nicotinate and its compounds with some bivalent transition metal ions

Energy Technology Data Exchange (ETDEWEB)

Nascimento, A.L.C.S. do; Caires, F.J., E-mail: caires.flavio@yahoo.com.br; Gomes, D.J.C.; Gigante, A.C.; Ionashiro, M.

2014-01-10

Graphical abstract: - Highlights: • The transition metal ion nicotinates were synthesized. • The TG–DTA curves provided previously unreported information about thermal behaviour. • The gaseous products released were detected by TG–DSC coupled to FTIR. - Abstract: Solid-state M(L){sub 2}·nH{sub 2}O compounds, where M stands for bivalent transition metals (Mn, Fe, Co, Ni, Cu and Zn), L is nicotinate and n = 0–4.5, have been synthesized. Characterization and thermal behaviour of these compounds were investigated employing elemental analysis based on the mass losses observed in the TG–DTA curves, complexometry, X-ray diffractometry, infrared spectroscopy (FTIR), simultaneous thermogravimetric and differential thermal analysis (TG–DTA) and TG–DSC coupled to FTIR. The thermal behaviour of nicotinic acid and its sodium salt was also investigated. For the hydrated transition metal compounds, the dehydration and thermal decomposition of the anhydrous compounds occur in a single step. For the sodium nicotinate, the final residue up to 765 °C is sodium carbonate and for the transition metal nicotinates, the final residues are Mn{sub 3}O{sub 4}, Fe{sub 2}O{sub 3}, Co{sub 3}O{sub 4}, NiO, CuO and ZnO. The results also provided information concerning the thermal stability, thermal decomposition and identification of the gaseous products evolved during the thermal decomposition of the compounds.

Thermal behaviour of nicotinic acid, sodium nicotinate and its compounds with some bivalent transition metal ions

International Nuclear Information System (INIS)

Nascimento, A.L.C.S. do; Caires, F.J.; Gomes, D.J.C.; Gigante, A.C.; Ionashiro, M.

2014-01-01

Graphical abstract: - Highlights: • The transition metal ion nicotinates were synthesized. • The TG–DTA curves provided previously unreported information about thermal behaviour. • The gaseous products released were detected by TG–DSC coupled to FTIR. - Abstract: Solid-state M(L) 2 ·nH 2 O compounds, where M stands for bivalent transition metals (Mn, Fe, Co, Ni, Cu and Zn), L is nicotinate and n = 0–4.5, have been synthesized. Characterization and thermal behaviour of these compounds were investigated employing elemental analysis based on the mass losses observed in the TG–DTA curves, complexometry, X-ray diffractometry, infrared spectroscopy (FTIR), simultaneous thermogravimetric and differential thermal analysis (TG–DTA) and TG–DSC coupled to FTIR. The thermal behaviour of nicotinic acid and its sodium salt was also investigated. For the hydrated transition metal compounds, the dehydration and thermal decomposition of the anhydrous compounds occur in a single step. For the sodium nicotinate, the final residue up to 765 °C is sodium carbonate and for the transition metal nicotinates, the final residues are Mn 3 O 4 , Fe 2 O 3 , Co 3 O 4 , NiO, CuO and ZnO. The results also provided information concerning the thermal stability, thermal decomposition and identification of the gaseous products evolved during the thermal decomposition of the compounds

Heterocycles by Transition Metals Catalyzed Intramolecular Cyclization of Acetylene Compounds

International Nuclear Information System (INIS)

Vizer, S.A.; Yerzhanov, K.B.; Dedeshko, E.C.

2003-01-01

Review shows the new strategies in the synthesis of heterocycles, having nitrogen, oxygen and sulfur atoms, via transition metals catalyzed intramolecular cyclization of acetylenic compounds on the data published at the last 30 years, Unsaturated heterocyclic compounds (pyrroles and pyrroline, furans, dihydro furans and benzofurans, indoles and iso-indoles, isoquinolines and isoquinolinones, aurones, iso coumarins and oxazolinone, lactams and lactones with various substitutes in heterocycles) are formed by transition metals, those salts [PdCl 2 , Pd(OAc) 2 , HgCl 2 , Hg(OAc) 2 , Hg(OCOCF 3 ) 2 , AuCl 3 ·2H 2 O, NaAuCl 4 ·2H 2 O, CuI, CuCl], oxides (HgO) and complexes [Pd(OAc) 2 (PPh 3 )2, Pd(PPh 3 ) 4 , PdCl 2 (MeCN) 2 , Pd(OAc ) 2 /TPPTS] catalyzed intramolecular cyclization of acetylenic amines, amides, ethers, alcohols, acids, ketones and βdiketones. More complex hetero polycyclic systems typical for natural alkaloids can to obtain similar. Proposed mechanisms of pyrroles, isoquinolines, iso indoles and indoles, benzofurans and iso coumarins, thiazolopyrimidinones formation are considered. (author)

Standard entropy for borides of non-transition metals, rare-earth metals and actinides

International Nuclear Information System (INIS)

Borovikova, M.S.

1986-01-01

Using as initial data the most reliable values of standard entropy for 10 compounds, the entropies for 40 compounds of non-transition metals, rare-earth metals and actinides have been evaluated by the method of comparative calculation. Taking into account the features of boride structures, two methods, i.e. additive and proportional, have been selected for the entropy calculations. For the range of borides the entropies were calculated from the linear relation of the latter to the number of boron atoms in the boride. For borides of rare-earth metals allowance has been made for magnetic contributions in conformity with the multiplicity of the corresponding ions. Insignificant differences in the electronic contributions to the entropy for borides and metals have been neglected. For dodecaborides only the additive method has been used. This is specified by the most rigid network that provides the same contribution to compound entropy. (orig.)

The intra-annular acylamide chelate-coordinated compound: The keto-tautomer of metal (II) milrinone complex

Science.gov (United States)

Gong, Yun; Liu, Jinzhi; Tang, Wang; Hu, Changwen

2008-03-01

In the presence of N, N'-dimethyllformamide (DMF), two isostructural metal (II)-milrinone complexes formulated as M(C 12H 8N 3O) 2 (M = Co 1 and Ni 2) have been synthesized and characterized by elemental analysis, IR, TG and single crystal X-ray diffraction. The two compounds crystallize in the tetragonal system, chiral space group P4 32 12. They exhibit similar two dimensional (2D) square grid-like framework, in which milrinone acts as a ditopic ligand with its terminal pyridine and intra-annular acylamide groups covalently bridging different metal centers. The intra-annular acylamide ligand shows a chelate-coordinated mode. Compounds 1 and 2 are stable under 200 °C. Compound 3 formulated as (C 12H 9N 3O) 4·H 2O was obtained in the presence of water, the water molecule in the structure leads to the racemization of compound 3 and it crystallizes in the monoclinic system, non-chiral space group P2 1/ c. Milrinone exhibits a keto-form in the three compounds and compounds 1- 3 exhibit different photoluminescence properties.

Data-Driven Derivation of an "Informer Compound Set" for Improved Selection of Active Compounds in High-Throughput Screening.

Science.gov (United States)

Paricharak, Shardul; IJzerman, Adriaan P; Jenkins, Jeremy L; Bender, Andreas; Nigsch, Florian

2016-09-26

Despite the usefulness of high-throughput screening (HTS) in drug discovery, for some systems, low assay throughput or high screening cost can prohibit the screening of large numbers of compounds. In such cases, iterative cycles of screening involving active learning (AL) are employed, creating the need for smaller "informer sets" that can be routinely screened to build predictive models for selecting compounds from the screening collection for follow-up screens. Here, we present a data-driven derivation of an informer compound set with improved predictivity of active compounds in HTS, and we validate its benefit over randomly selected training sets on 46 PubChem assays comprising at least 300,000 compounds and covering a wide range of assay biology. The informer compound set showed improvement in BEDROC(α = 100), PRAUC, and ROCAUC values averaged over all assays of 0.024, 0.014, and 0.016, respectively, compared to randomly selected training sets, all with paired t-test p-values agnostic fashion. This approach led to a consistent improvement in hit rates in follow-up screens without compromising scaffold retrieval. The informer set is adjustable in size depending on the number of compounds one intends to screen, as performance gains are realized for sets with more than 3,000 compounds, and this set is therefore applicable to a variety of situations. Finally, our results indicate that random sampling may not adequately cover descriptor space, drawing attention to the importance of the composition of the training set for predicting actives.

Coordination compounds of metals with imidazoles and benzimidazoles. [Metals: V, Th, Mo, Cd, rare earths, etc

Energy Technology Data Exchange (ETDEWEB)

Novikova, G A; Molodkin, A K; Kukalenko, S S

1988-12-01

Methods of preparation, composition and structure of UO/sub 2//sup 2+/, Th/sup 4+/, Mo/sup 3+/, Cd/sup 2+/, Ln/sup 3+/ metal ion complexes with imidazoles and benzimidazoles are considered in reviews of native and foreign literature of up to 1985. Complexes are customarily prepared by direct interaction of ligands with inorganic salts in different organic solvents. Complex composition is defined by the nature of complexing metal and inorganic salt anion, ligand volume and basicity, as well as solvent characteristics. Effect of R substituent in imidazole and benzimidazole side chain on composition of coordination compounds is considered.

Genetic toxicology of metal compounds. II. Enhancement of ultraviolet light-induced mutagenesis in Escherichia coli WP2

International Nuclear Information System (INIS)

Rossman, T.G.; Molina, M.

1986-01-01

Salts of metals which are carcinogenic, noncarcinogenic, or of unknown carcinogenicity were assayed for their abilities to modulate ultraviolet (UV)-induced mutagenesis in Escherichia coli WP2. In addition to the previously reported comutagenic effect of arsenite, salts of three other compounds were found to enhance UV mutagenesis. CuCl 2 , MnCl 2 (and a small effect by KMnO 4 ), and NaMoO 4 acted as comutagens in E coli WP2, which has wild-type DNA repair capability, but were much less comutagenic in the repair deficient strain WP2/sub s/ (uvrA). The survival of irradiated or unirradiated cells was not affected by these compounds. No effects on UV mutagenesis were seen for 16 other metal compounds. We suggest that the comutagenic effects might occur either via metal-induced decreases in the fidelity of repair replication or via metal-induced depurination

Correlated effective field theory in transition metal compounds

International Nuclear Information System (INIS)

Mukhopadhyay, Subhasis; Chatterjee, Ibha

2004-01-01

temperature, stoichiometric composition. The magnetic properties of these compounds can be studied very well with the CEF theory. The physics of the insulating phase should definitely play an important role in these oxides which show metallic and superconducting behaviour as a function of doping in the parent compounds which are Mott insulators

Fundamental Studies of the Reforming of Oxygenated Compounds over Supported Metal Catalysts

Energy Technology Data Exchange (ETDEWEB)

Dumesic, James A. [Univ. of Wisconsin, Madison, WI (United States)

2016-01-04

The main objective of our research has been to elucidate fundamental concepts associated with controlling the activity, selectivity, and stability of bifunctional, metal-based heterogeneous catalysts for tandem reactions, such as liquid-phase conversion of oxygenated hydrocarbons derived from biomass. We have shown that bimetallic catalysts that combine a highly-reducible metal (e.g., platinum) with an oxygen-containing metal promoter (e.g., molybdenum) are promising materials for conversion of oxygenated hydrocarbons because of their high activity for selective cleavage for carbon-oxygen bonds. We have developed methods to stabilize metal nanoparticles against leaching and sintering under liquid-phase reaction conditions by using atomic layer deposition (ALD) to apply oxide overcoat layers. We have used controlled surface reactions to produce bimetallic catalysts with controlled particle size and controlled composition, with an important application being the selective conversion of biomass-derived molecules. The synthesis of catalysts by traditional methods may produce a wide distribution of metal particle sizes and compositions; and thus, results from spectroscopic and reactions kinetics measurements have contributions from a distribution of active sites, making it difficult to assess how the size and composition of the metal particles affect the nature of the surface, the active sites, and the catalytic behavior. Thus, we have developed methods to synthesize bimetallic nanoparticles with controlled particle size and controlled composition to achieve an effective link between characterization and reactivity, and between theory and experiment. We have also used ALD to modify supported metal catalysts by addition of promoters with atomic-level precision, to produce new bifunctional sites for selective catalytic transformations. We have used a variety of techniques to characterize the metal nanoparticles in our catalysts, including scanning transmission electron

Secondary electron emission from metals and semi-conductor compounds

International Nuclear Information System (INIS)

Ono, Susumu; Kanaya, Koichi

1979-01-01

Attempt was made to present the sufficient solution of the secondary electron yield of metals and semiconductor compounds except insulators, applying the free electron scattering theory to the absorption of secondary electrons generated within a solid target. The paper is divided into the sections describing absorption coefficient and escape depth, quantitative characteristics of secondary yield, angular distribution of secondary electron emission, effect of incident angle to secondary yield, secondary electron yield transmitted, and lateral distribution of secondary electron emission, besides introduction and conclusion. The conclusions are as follows. Based on the exponential power law for screened atomic potential, secondary electron emission due to both primary and backscattered electrons penetrating into metallic elements and semi-conductive compounds is expressed in terms of the ionization loss in the first collision for escaping secondary electrons. The maximum yield and the corresponding primary energy can both consistently be derived as the functions of three parameters: atomic number, first ionization energy and backscattering coefficient. The yield-energy curve as a function of the incident energy and the backscattering coefficient is in good agreement with the experimental results. The energy dependence of the yield in thin films and the lateral distribution of secondary yield are derived as the functions of the backscattering coefficient and the primary energy. (Wakatsuki, Y.)

Anti-trypanosomal activities and structural chemical properties of selected compound classes.

Science.gov (United States)

Ponte-Sucre, Alicia; Bruhn, Heike; Schirmeister, Tanja; Cecil, Alexander; Albert, Christian R; Buechold, Christian; Tischer, Maximilian; Schlesinger, Susanne; Goebel, Tim; Fuß, Antje; Mathein, Daniela; Merget, Benjamin; Sotriffer, Christoph A; Stich, August; Krohne, Georg; Engstler, Markus; Bringmann, Gerhard; Holzgrabe, Ulrike

2015-02-01

Potent compounds do not necessarily make the best drugs in the market. Consequently, with the aim to describe tools that may be fundamental for refining the screening of candidates for animal and preclinical studies and further development, molecules of different structural classes synthesized within the frame of a broad screening platform were evaluated for their trypanocidal activities, cytotoxicities against murine macrophages J774.1 and selectivity indices, as well as for their ligand efficiencies and structural chemical properties. To advance into their modes of action, we also describe the morphological and ultrastructural changes exerted by selected members of each compound class on the parasite Trypanosoma brucei. Our data suggest that the potential organelles targeted are either the flagellar pocket (compound 77, N-Arylpyridinium salt; 15, amino acid derivative with piperazine moieties), the endoplasmic reticulum membrane systems (37, bisquaternary bisnaphthalimide; 77, N-Arylpyridinium salt; 68, piperidine derivative), or mitochondria and kinetoplasts (88, N-Arylpyridinium salt; 68, piperidine derivative). Amino acid derivatives with fumaric acid and piperazine moieties (4, 15) weakly inhibiting cysteine proteases seem to preferentially target acidic compartments. Our results suggest that ligand efficiency indices may be helpful to learn about the relationship between potency and chemical characteristics of the compounds. Interestingly, the correlations found between the physico-chemical parameters of the selected compounds and those of commercial molecules that target specific organelles indicate that our rationale might be helpful to drive compound design toward high activities and acceptable pharmacokinetic properties for all compound families.

Effects of metal compounds with distinct physicochemical properties on iron homeostasis and antibacterial activity in the lungs: chromium and vanadium.

Science.gov (United States)

Cohen, Mitchell D; Sisco, Maureen; Prophete, Colette; Yoshida, Kotaro; Chen, Lung-chi; Zelikoff, Judith T; Smee, Jason; Holder, Alvin A; Stonehuerner, Jacqueline; Crans, Debbie C; Ghio, Andrew J

2010-02-01

In situ reactions of metal ions or their compounds are important mechanisms by which particles alter lung immune responses. The authors hypothesized that major determinants of the immunomodulatory effect of any metal include its redox behavior/properties, oxidation state, and/or solubility, and that the toxicities arising from differences in physicochemical parameters are manifest, in part, via differential shifts in lung iron (Fe) homeostasis. To test the hypotheses, immunomodulatory potentials for both pentavalent vanadium (VV; as soluble metavanadate or insoluble vanadium pentoxide) and hexavalent chromium (CrVI; as soluble sodium chromate or insoluble calcium chromate) were quantified in rats after inhalation (5h/day for 5 days) of each at 100 microg metal/m3. Differences in effects on local bacterial resistance between the two VV, and between each CrVI, agents suggested that solubility might be a determinant of in situ immunotoxicity. For the soluble forms, VV had a greater impact on resistance than CrVI, indicating that redox behavior/properties was likely also a determinant. The soluble VV agent was the strongest immunomodulant. Regarding Fe homeostasis, both VV agents had dramatic effects on airway Fe levels. Both also impacted local immune/airway epithelial cell Fe levels in that there were significant increases in production of select cytokines/chemokines whose genes are subject to regulation by HIF-1 (whose intracellular longevity is related to cell Fe status). Our findings contribute to a better understanding of the role that metal compound properties play in respiratory disease pathogenesis and provide a rationale for differing pulmonary immunotoxicities of commonly encountered ambient metal pollutants.

First-principles study of new quaternary Heusler compounds without 3d transition metal elements: ZrRhHfZ (Z = Al, Ga, In)

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiaotian [School of Material Sciences and Engineering, Hebei University of Technology, Tianjin 300130 (China); Institute for Superconducting & Electronic Materials (ISEM), University of Wollongong, Wollongong 2500 (Australia); Cheng, Zhenxiang, E-mail: cheng@uow.edu.au [Institute for Superconducting & Electronic Materials (ISEM), University of Wollongong, Wollongong 2500 (Australia); Guo, Ruikang [School of Material Sciences and Engineering, Hebei University of Technology, Tianjin 300130 (China); Wang, Jianli [Institute for Superconducting & Electronic Materials (ISEM), University of Wollongong, Wollongong 2500 (Australia); Rozale, Habib [Condensed Matter and Sustainable Development Laboratory, Physics Department, University of Sidi-Bel-Abbès, 22000 Sidi-Bel-Abbès (Algeria); Wang, Liying [Department of Physics, Tianjin University, Tianjin 300350 (China); Yu, Zheyin [Institute for Superconducting & Electronic Materials (ISEM), University of Wollongong, Wollongong 2500 (Australia); Liu, Guodong, E-mail: gdliu1978@126.com [School of Material Sciences and Engineering, Hebei University of Technology, Tianjin 300130 (China)

2017-06-01

Plane-wave pseudo-potential methods based on density functional theory are employed to investigate the electronic structures, and the magnetic and half-metallic properties of the newly designed quaternary Heusler compounds ZrRhHfZ (Z = Al, Ga, In) without 3d transition metal elements. The calculated results show that ZrRhHfZ (Z = Al, Ga, In) compounds are half-metallic, with 100% spin polarization around the Fermi level. The structural stability of these compounds has been tested from the aspects of their cohesion energy and formation. The spin-flip/half-metallic gaps of ZrRhHfZ (Z = Al, Ga, In) compounds are quite large, with values of 0.2548 eV, 0.3483 eV, and 0.2866 eV, respectively. These compounds show Slater-Pauling behavior, and the total spin magnetic moment per unit cell (M{sub t}) scales with the total number of valence electrons (Z{sub t}) following the rule: M{sub t} = Z{sub t} - 18. The magnetization of ZrRhHfZ (Z = Al, Ga, In) compounds mainly comes from the 4d electrons of the Zr atoms and the 5d electrons of the Hf atoms. Furthermore, the effects of uniform strain and tetragonal deformation on the half metallicity has been investigated in detail, which is important for practical application. Finally, we reveal that the half-metallicity can be maintained when the Coulomb interactions are considered. - Highlights: • New quaternary compounds without 3d transition metal elements have been designed. • The electronic structures and magnetism of the ZrRhHfZ compounds have been studied. • The effect of strain on the half-metallic behavior has been tested. • The effect of the Coulomb interactions on the half-metallicity has been investigated.

Single-layer dispersions of transition metal dichalcogenides in the synthesis of intercalation compounds

International Nuclear Information System (INIS)

Golub, Alexander S; Zubavichus, Yan V; Slovokhotov, Yurii L; Novikov, Yurii N

2003-01-01

Chemical methods for the exfoliation of transition metal dichalcogenides in a liquid medium to give single-layer dispersions containing quasi-two-dimensional layers of these compounds are surveyed. Data on the structure of dispersions and their use in the synthesis of various types of heterolayered intercalation compounds are discussed and described systematically. Structural features, the electronic structure and the physicochemical properties of the resulting intercalation compounds are considered. The potential of this method of synthesis is compared with that of traditional solid-state methods for the intercalation of layered crystals.

Apoptosis induction in human lymphocytes after in vitro exposure to cobalt/hard metal compounds

International Nuclear Information System (INIS)

Boeck, M. de; Decordier, I.; Lombaert, N.; Cundari, E.; Kirsch-Volders, M.; Lison, D.

2001-01-01

Full text: An increased risk of lung cancer is associated with occupational exposure to mixtures of cobalt metal (Co) and tungsten carbide (WC) particles, but apparently not when exposure is to cobalt alone. The mechanism for this increased cancer risk is not fully understood. The evaluation of the in vitro genotoxic effects in lymphocytes exposed to varying cobalt species demonstrated that the WC-Co hard metal mixture is more genotoxic (DNA damage, chromosome/genome mutations) than metallic Co alone. WC alone was not genotoxic. Thus, WC-Co represents a specific (geno)toxic entity. In order to assess the survival of human lymphocytes after in vitro exposure to metallic Co, CoCl 2 , WC and the WC-Co mixture, two apoptosis/necrosis detection methods were applied (annexin V staining and flow cytometry). Annexin-V staining of early apoptotic cells demonstrated a dose- and time dependent induction of apoptosis by metallic Co, CoCl 2 , WC and the WC-Co mixture. The time course of the process varied according to the metal species tested. Metallic Co and CoCl 2 caused a gradually increasing frequency of apoptotic cells with time (up to 24 h). WC-induced apoptosis displayed a typical 6 hour peak, which was not the case for the WC-Co mixture or for Co. Apoptosis induction by the WC-Co mixture was intermediate between that induced by Co and WC separately. Analysis of propidium iodide stained cells by flow cytometry was performed as a later marker for apoptosis induction. Preliminary data indicate similar tendencies of apoptosis induction as those detected by annexin-V. Identification of the apoptotic pathway triggered by the metal compounds was studied by inhibition of the ceramide-apoptosis pathway by fumonisin causing reduction of apoptosis induction for all compounds, but strongest after 6 hour exposure to WC. The use of specific caspase inhibitors will allow to further elucidate the different pathways involved. The current data demonstrating in vitro the apoptosis

Apoptosis induction in human lymphocytes after in vitro exposure to cobalt/hard metal compounds

Energy Technology Data Exchange (ETDEWEB)

Boeck, M de; Decordier, I; Lombaert, N; Cundari, E; Kirsch-Volders, M [Vrije Universiteit Brussel, Laboratorium voor Cellulaire Genetica, Brussel (Belgium); Lison, D [Universite catholique de Louvain, Unite de Toxicologie industrielle et Medecine du Travail, Bruxelles (Belgium)

2001-07-01

Full text: An increased risk of lung cancer is associated with occupational exposure to mixtures of cobalt metal (Co) and tungsten carbide (WC) particles, but apparently not when exposure is to cobalt alone. The mechanism for this increased cancer risk is not fully understood. The evaluation of the in vitro genotoxic effects in lymphocytes exposed to varying cobalt species demonstrated that the WC-Co hard metal mixture is more genotoxic (DNA damage, chromosome/genome mutations) than metallic Co alone. WC alone was not genotoxic. Thus, WC-Co represents a specific (geno)toxic entity. In order to assess the survival of human lymphocytes after in vitro exposure to metallic Co, CoCl{sub 2}, WC and the WC-Co mixture, two apoptosis/necrosis detection methods were applied (annexin V staining and flow cytometry). Annexin-V staining of early apoptotic cells demonstrated a dose- and time dependent induction of apoptosis by metallic Co, CoCl{sub 2}, WC and the WC-Co mixture. The time course of the process varied according to the metal species tested. Metallic Co and CoCl{sub 2} caused a gradually increasing frequency of apoptotic cells with time (up to 24 h). WC-induced apoptosis displayed a typical 6 hour peak, which was not the case for the WC-Co mixture or for Co. Apoptosis induction by the WC-Co mixture was intermediate between that induced by Co and WC separately. Analysis of propidium iodide stained cells by flow cytometry was performed as a later marker for apoptosis induction. Preliminary data indicate similar tendencies of apoptosis induction as those detected by annexin-V. Identification of the apoptotic pathway triggered by the metal compounds was studied by inhibition of the ceramide-apoptosis pathway by fumonisin causing reduction of apoptosis induction for all compounds, but strongest after 6 hour exposure to WC. The use of specific caspase inhibitors will allow to further elucidate the different pathways involved. The current data demonstrating in vitro the

Structure and catalytic properties of metal β-diketonate complexes with oxygen-containing compounds

International Nuclear Information System (INIS)

Nizel'skij, Yu.N.; Ishchenko, S.S.; Lipatova, T.Eh.

1985-01-01

The results of researches published in recent 15-20 years of complexes of metal β-diketonates (including Cr 3+ , VO 2+ , MoOΛ2 2+ , Co 3+ , Mn 3+ , Ni 2+ , Fe 3+ ) with oxygen-containing compounds (alcohols, glycols, phenols, hydroperoxides, aldehydes, esters, etc.) playing an important role in catalytic processes of oxidation, addition, polymerization and copolymerization are reviewed. Data on the nature of chemical bond of oxygen-containing reacting agents with metal β-diketonates, on structure of metal β-diketonate complexes with oxygen-containing reacting agents and thermodynamics of complexing as well as on activation of reacting agents in complexes and catalytic properties of metal β-diketonates are discussed. Stored materials make it possible to exercise directed control of metal β-diketonate activity

Metal selective co-ordinative self-assembly of π-donors

Indian Academy of Sciences (India)

Metal selective co-ordinative nanostructures were constructed by the supramolecular ... observed an anomalous binding of metal ion to the core sulphur groups causing redox changes in the TTF ... attention on metal-assisted co-ordinative self-assembly ..... M TTF-Py in 1:1 CHCl3: MeCN and (c) photographs showing visual.

Uranium Metal Analysis via Selective Dissolution

Energy Technology Data Exchange (ETDEWEB)

Delegard, Calvin H.; Sinkov, Sergey I.; Schmidt, Andrew J.; Chenault, Jeffrey W.

2008-09-10

Uranium metal, which is present in sludge held in the Hanford Site K West Basin, can create hazardous hydrogen atmospheres during sludge handling, immobilization, or subsequent transport and storage operations by its oxidation/corrosion in water. A thorough knowledge of the uranium metal concentration in sludge therefore is essential to successful sludge management and waste process design. The goal of this work was to establish a rapid routine analytical method to determine uranium metal concentrations as low as 0.03 wt% in sludge even in the presence of up to 1000-fold higher total uranium concentrations (i.e., up to 30 wt% and more uranium) for samples to be taken during the upcoming sludge characterization campaign and in future analyses for sludge handling and processing. This report describes the experiments and results obtained in developing the selective dissolution technique to determine uranium metal concentration in K Basin sludge.

Diazo compounds and N-tosylhydrazones: novel cross-coupling partners in transition-metal-catalyzed reactions.

Science.gov (United States)

Xiao, Qing; Zhang, Yan; Wang, Jianbo

2013-02-19

Transition-metal-catalyzed carbene transformations and cross-couplings represent two major reaction types in organometallic chemistry and organic synthesis. However, for a long period of time, these two important areas have evolved separately, with essentially no overlap or integration. Thus, an intriguing question has emerged: can cross-coupling and metal carbene transformations be merged into a single reaction cycle? Such a combination could facilitate the development of novel carbon-carbon bond-forming methodologies. Although this concept was first explored about 10 years ago, rapid developments inthis area have been achieved recently. Palladium catalysts can be used to couple diazo compounds with a wide variety of organic halides. Under oxidative coupling conditions, diazo compounds can also react with arylboronic acids and terminal alkynes. Both of these coupling reactions form carbon-carbon double bonds. As the key step in these catalytic processes, Pd carbene migratory insertion plays a vital role in merging the elementary steps of Pd intermediates, leading to novel carbon-carbon bond formations. Because the diazo substrates can be generated in situ from N-tosylhydrazones in the presence of base, the N-tosylhydrazones can be used as reaction partners, making this type of cross-coupling reaction practical in organic synthesis. N-Tosylhydrazones are easily derived from the corresponding aldehydes or ketones. The Pd-catalyzed cross-coupling of N-tosylhydrazones is considered a complementary reaction to the classic Shapiro reaction for converting carbonyl functionalities into carbon-carbon double bonds. It can also serve as an alternative approach for the Pd-catalyzed cross-coupling of carbonyl compounds, which is usually achieved via triflates. The combination of carbene formation and cross-coupling in a single catalytic cycle is not limited to Pd-catalyzed reactions. Recent studies of Cu-, Rh-, Ni-, and Co-catalyzed cross-coupling reactions with diazo

Metal hydride compositions and lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Young, Kwo; Nei, Jean

2018-04-24

Heterogeneous metal hydride (MH) compositions comprising a main region comprising a first metal hydride and a secondary region comprising one or more additional components selected from the group consisting of second metal hydrides, metals, metal alloys and further metal compounds are suitable as anode materials for lithium ion cells. The first metal hydride is for example MgH.sub.2. Methods for preparing the composition include coating, mechanical grinding, sintering, heat treatment and quenching techniques.

Investigations in anhydrous liquid ammonia. Reaction of group 2, 4, 5, 11 metal and actinoids compounds

International Nuclear Information System (INIS)

Woidy, Patrick

2014-01-01

The solubility and reactivity of metal halides, transition metal halides, and actinoid halides in liquid ammonia can lead to new starting materials for the synthesis of fluorides in low oxidation states or for nitrides via a ''low-temperature route''. In this context the ability of metal and actinoid halides to act as an acceptor for or donor of fluoride ions is also of interest. Four different systems were investigated in this study. In the first section, the synthesis and characterization of new compounds were carried out in the system CuX/NH 3 (X = F, Cl, Br, I, and CN) and lead to a ligand stabilized monovalent copper fluoride as a main result. In the second section, the solubility of uranyl compounds and uranium halides in liquid ammonia was investigated and the products were characterized. In the third section, alkali metal thorates were synthesized. Their solubility in liquid ammonia and their behavior as an acceptor for fluoride ions was investigated. In the last section, the results on the solubility behavior of transition metal halides in liquid ammonia and their coordination behavior are presented. In the first system CuX/NH 3 several new compounds, such as [Cu(NH 3 ) 3 ]X (X = Br, I or CN) were synthesized and characterized. The reactions of this compounds with fluoride ion donors (NH 4 F or Me 4 NF) led unfortunately not to the monovalent copper fluoride CuF. The comproportionation reaction of Cu and CuF 2 in liquid ammonia lead to the compounds [Cu(NH 3 ) 3 ] 2 [Cu 2 (NH 3 ) 2 ] . 4 NH 3 and [Cu(NH 3 ) 2 ]F . NH 3 . For the preparation of binary CuF, various decomposition experiments were executed on the compound [Cu(NH 3 ) 2 ]F . NH 3 which resulted in different decomposition products. In additional studies various complexes of divalent copper was investigated and with the compound [Cu(NH 3 ) 5 ]F 2 . NH 3 the solubility of fluoride containing substances in liquid ammonia could be shown. Studies of six- and tetravalent uranium

Ionothermal synthesis and structural transformation targeted by ion exchange in metal-1,3,5-benzenetricarboxylate compounds

Energy Technology Data Exchange (ETDEWEB)

Xu, Qing-Qing [Key Laboratory of Macromolecular Science of Shaanxi Province, School of Chemistry & Chemical Engineering, Shaanxi Normal University, Xi’an 710062, Shaanxi (China); State Key Laboratory of Structural Chemistry, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Liu, Bing [College of Chemistry and Chemical Engineering, Shaanxi University of Sciences and Technology, Xi’an 710021, Shaanxi (China); Xu, Ling, E-mail: xuling@snnu.edu.cn [Key Laboratory of Macromolecular Science of Shaanxi Province, School of Chemistry & Chemical Engineering, Shaanxi Normal University, Xi’an 710062, Shaanxi (China); Jiao, Huan, E-mail: jiaohuan@snnu.edu.cn [Key Laboratory of Macromolecular Science of Shaanxi Province, School of Chemistry & Chemical Engineering, Shaanxi Normal University, Xi’an 710062, Shaanxi (China)

2017-03-15

Ionothermal reactions of 1,3,5-benzenetricarboxylate acid (H{sub 3}BTC) and Ni(NO{sub 3}){sub 2}, Co(NO{sub 3}){sub 2} and Cu(NO{sub 3}){sub 2} gave two discrete 32-membered ring-like allomers, [M{sub 2}(HBTC){sub 2}(NH{sub 2}CONH{sub 2}){sub 2}(H{sub 2}O){sub 4}]·3H{sub 2}O (M=Ni(1), Co(2)) and one layered [Cu{sub 2}(BTC)Cl(H{sub 2}O){sub 4}] (3). The weak interactions in 1 can be deconstructed to some degree in ion exchange by exploring the factors of divalent and trivalent metal species, metal concentration and soaking time, which are demonstrated by PXRD and N{sub 2} absorption. Cu{sup 2+} has the highest N{sub 2} adsorbance when soaking with 1, and 1 can keep structure stable when Cu{sup 2+} below 0.16 mol L{sup −1} and the soaking time within 24d. As Cu{sup 2+} beyond 0.16 mol L{sup −1} and the soaking time beyond 24d, the structure of compound 1 starts to transform with the crystal morphology from clear pale green to opaque blue. Ionothermal reactions of compound 1 with different Cu{sup 2+} amounts obtained Ni{sup 2+}-Cu{sup 2+} hetero complexes, whose PXRD patterns are similar to that of 3 and EDS indicates Cu{sup 2+}% increases with Cu{sup 2+} additions and close to 100% as Cu{sup 2+} being 1.6 mmol. It suggests that 3 is a controlled product and Cu{sup 2+} can transform discrete compound 1 into 2D compound 3. - Graphical abstract: Three compounds were synthesized through ionothermal reactions. The weak interactions in compound 1 can be deconstructed by ion exchange and discrete compound 1 can be transformed into layered compound 3. - Highlights: • Two discrete ring-like and one layered compounds were ionothermally synthesized. • Metal species, metal concentration and soaking time deconstruct the H-bondings in 1. • 1 can be transformed to 3 through ionothermal reaction, otherwise forbidden.

Mixed valence transition metal 2D-oxides: Comparison between delafossite and crednerite compounds

Science.gov (United States)

Martin, Christine; Poienar, Maria

2017-08-01

Transition metal oxides offer large opportunities to study relationships between structures and properties. Indeed these compounds crystallize in numerous frameworks corresponding to different dimensionalities and, accordingly, show a huge variety of properties (as high Tc superconductivity, colossal magnetoresistivity, multiferroicity..). The control of the oxidation state of the transition metal, via the monitoring of the oxygen content, is of prime importance to understand and optimize the properties, due to the strong coupling that exists between the lattice and the charges and spins of the transition metals. In this large playground for chemists, we reinvestigated several 2D-compounds derived from delafossite structure. Considering this paper as a very short review, we report here the results obtained on CuMO2 compounds (with M = Cr, Mn or Mn+Cu) by using a combination of techniques, as X-ray, neutrons and/or electrons diffraction on poly-crystals for structural characterisations that are correlated with electrical and/or magnetic properties. The complementarity of studies is also addressed by the synthesis and characterization of single crystals in addition to poly-crystals. Moreover the comparison of the structures of similar Cr and Mn based oxides highlights the crucial role of the Jahn-Teller effect of trivalent manganese to lift the degeneracy, which is responsible of the magnetic frustration in CuCrO2.

Plasmachemical synthesis and evaluation of the thermal conductivity of metal-oxide compounds "Molybdenum-uranium dioxide"

Science.gov (United States)

Kotelnikova, Alexandra A.; Karengin, Alexander G.; Mendoza, Orlando

2018-03-01

The article represents possibility to apply oxidative and reducing plasma for plasma-chemical synthesis of metal-oxide compounds «Mo‒UO2» from water-salt mixtures «molybdic acid‒uranyl nitrate» and «molybdic acid‒ uranyl acetate». The composition of water-salt mixture was calculated and the conditions ensuring plasma-chemical synthesis of «Mo‒UO2» compounds were determined. Calculations were carried out at atmospheric pressure over a wide range of temperatures (300-4000 K), with the use of various plasma coolants (air, hydrogen). The heat conductivity coefficients of metal-oxide compounds «Mo‒UO2» consisting of continuous component (molybdenum matrix) are calculated. Inclusions from ceramics in the form of uranium dioxide were ordered in the matrix. Particular attention is paid to methods for calculating the coefficients of thermal conductivity of these compounds with the use of different models. Calculated results were compared with the experimental data.

Potential value of phosphate compounds in enhancing immobilization and reducing bioavailability of mixed heavy metal contaminants in shooting range soil.

Science.gov (United States)

Seshadri, B; Bolan, N S; Choppala, G; Kunhikrishnan, A; Sanderson, P; Wang, H; Currie, L D; Tsang, Daniel C W; Ok, Y S; Kim, G

2017-10-01

Shooting range soils contain mixed heavy metal contaminants including lead (Pb), cadmium (Cd), and zinc (Zn). Phosphate (P) compounds have been used to immobilize these metals, particularly Pb, thereby reducing their bioavailability. However, research on immobilization of Pb's co-contaminants showed the relative importance of soluble and insoluble P compounds, which is critical in evaluating the overall success of in situ stabilization practice in the sustainable remediation of mixed heavy metal contaminated soils. Soluble synthetic P fertilizer (diammonium phosphate; DAP) and reactive (Sechura; SPR) and unreactive (Christmas Island; CPR) natural phosphate rocks (PR) were tested for Cd, Pb and Zn immobilization and later their mobility and bioavailability in a shooting range soil. The addition of P compounds resulted in the immobilization of Cd, Pb and Zn by 1.56-76.2%, 3.21-83.56%, and 2.31-74.6%, respectively. The reactive SPR significantly reduced Cd, Pb and Zn leaching while soluble DAP increased their leachate concentrations. The SPR reduced the bioaccumulation of Cd, Pb and Zn in earthworms by 7.13-23.4% and 14.3-54.6% in comparison with earthworms in the DAP and control treatment, respectively. Bioaccessible Cd, Pb and Zn concentrations as determined using a simplified bioaccessibility extraction test showed higher long-term stability of P-immobilized Pb and Zn than Cd. The differential effect of P-induced immobilization between P compounds and metals is due to the variation in the solubility characteristics of P compounds and nature of metal phosphate compounds formed. Therefore, Pb and Zn immobilization by P compounds is an effective long-term remediation strategy for mixed heavy metal contaminated soils. Copyright © 2017 Elsevier Ltd. All rights reserved.

Metal complexes in cancer therapy – an update from drug design perspective

Directory of Open Access Journals (Sweden)

Ndagi U

2017-03-01

Full Text Available Umar Ndagi, Ndumiso Mhlongo, Mahmoud E Soliman Molecular Modelling and Drug Design Research Group, School of Health Sciences, University of KwaZulu-Natal, Westville, Durban, South Africa Abstract: In the past, metal-based compounds were widely used in the treatment of disease conditions, but the lack of clear distinction between the therapeutic and toxic doses was a major challenge. With the discovery of cisplatin by Barnett Rosenberg in 1960, a milestone in the history of metal-based compounds used in the treatment of cancers was witnessed. This forms the foundation for the modern era of the metal-based anticancer drugs. Platinum drugs, such as cisplatin, carboplatin and oxaliplatin, are the mainstay of the metal-based compounds in the treatment of cancer, but the delay in the therapeutic accomplishment of other metal-based compounds hampered the progress of research in this field. Recently, however, there has been an upsurge of activities relying on the structural information, aimed at improving and developing other forms of metal-based compounds and nonclassical platinum complexes whose mechanism of action is distinct from known drugs such as cisplatin. In line with this, many more metal-based compounds have been synthesized by redesigning the existing chemical structure through ligand substitution or building the entire new compound with enhanced safety and cytotoxic profile. However, because of increased emphasis on the clinical relevance of metal-based complexes, a few of these drugs are currently on clinical trial and many more are awaiting ethical approval to join the trial. In this review, we seek to give an overview of previous reviews on the cytotoxic effect of metal-based complexes while focusing more on newly designed metal-based complexes and their cytotoxic effect on the cancer cell lines, as well as on new approach to metal-based drug design and molecular target in cancer therapy. We are optimistic that the concept of selective

Deuterium enrichment by selective photo-induced dissociation of an organic carbonyl compound

International Nuclear Information System (INIS)

Marling, J.B.

1981-01-01

A deuterium-enriched material is produced by selective photoinduced dissociation of a gas phase organic carbonyl compound containing at least one hydrogen atom bonded to an atom adjacent to a carbonyl group. Alkyl carbonyl compounds such as acetone, acetaldehyde, trifluoroacetic acid, cyclobutanone, cyclopentanone, methyl acetate, 3,3-dimethyl-2-butanone, 2,4-pentanedione, and 4-methyl-2-pentanone are preferred. The carbonyl compound is subjected to intense infrared radiation from one laser, or two lasers operating at different frequencies, to selectively dissociate the deuterated molecules into stable products. The undissociated compound may be redeuterated by direct aqueous liquid phase H/D exchange, or by indirect liquid phase exchange using an alkanol in an intermediate step

Data on Occurrence of Selected Trace Metals, Organochlorines, and Semivolatile Organic Compounds in Edible Fish Tissues From Lake Worth, Fort Worth, Texas 1999

National Research Council Canada - National Science Library

Moring, J. B

2002-01-01

.... Air Force and in collaboration with the Texas Department of Health, collected samples of edible fish tissues from Lake Worth for analysis of selected trace metals, organochlorines, and semivolatile...

Method for hydrometallurgical recovery of selected metals

International Nuclear Information System (INIS)

Lorenz, G.; Schaefer, B.; Balzat, W.

1988-01-01

The method for hydrometallurgical recovery of selected metals refers to ore dressing by means of milling and alkaline leaching of metals, preferably uranium. By adding CaO during wet milling, Na + or K + ions of clayey ores are replaced by Ca 2+ ions. Due to the ion exchange processes, the uranium bonded with clays becomes more accessible to the leaching solution. The uranium yield increases and the consumption of reagents decreases

Selectivity in stripping of alkali-metal cations from crown ether carboxylate complexes

International Nuclear Information System (INIS)

Bartsch, R.A.; Walkowiak, W.; Robison, T.W.

1992-01-01

To probe the effect of structural variations within the ionophore upon the efficiency and selectivity of solvent extraction, a variety of crown ether carboxylic acids and phosphonic acid monoesters have been synthesized. In other studies the influence of the organic diluent upon extraction efficiency and selectivity has been probed for such proton-ionizable crown ethers. In the present investigation, attention is focused upon selectivity in the stripping step. Although the efficiency of metal ion stripping is often examined in solvent extraction studies, the selectivity of competitive metal ion release under different conditions is much less frequently considered. In this study, competitive stripping of metal ions from chloroform solutions of five-alkali-metal crown ether carboxylates by varying concentrations of aqueous hydrochloric acid is examined. Alkali metals used were Li, Na, K, Rb, and Cs

Melamine phosphomolybdate - a new ion selective compound for caesium

International Nuclear Information System (INIS)

Mehta, B.J.; Baxi, D.R.

1976-01-01

Preparation of melamine phosphomolybdate is described and its composition is determined. The compound is found to be granular having much higher selectivity for Cs + than that of ammonium phosphomolybdate. (orig.) [de

Periodicity effects on compound waves guided by a thin metal slab sandwiched between two periodically nonhomogeneous dielectric materials

Science.gov (United States)

Chiadini, Francesco; Fiumara, Vincenzo; Scaglione, Antonio; Lakhtakia, Akhlesh

2017-10-01

Surface-plasmon-polariton waves can be compounded when a sufficiently thin metal layer is sandwiched between two half spaces filled with dissimilar periodically nonhomogeneous dielectric materials. We solved the boundary-value problem for compound waves guided by a layer of a homogeneous and isotropic metal sandwiched between a structurally chiral material (SCM) and a periodically multilayered isotropic dielectric (PMLID) material. We found that the periodicities of the PMLID material and the SCM are crucial to excite a multiplicity of compound guided waves arising from strong coupling between the two interfaces.

New perspectives for the petroleum industry. Bioprocesses for the selective removal of sulphur, nitrogen and metals

International Nuclear Information System (INIS)

Zerlia, T.

2000-01-01

Fuel biocatalytic conversion is a process that removes, through selective enzyme-catalyzed reactions, sulphur, nitrogen and metals. The mild operating conditions, the specificity of reactions and the quality of coproducts (particularly the organo sulphur compounds, a source for the petrochemical industry) are just a few of the attractive aspects of this new technology which could open a new world of possibilities in the technology and in the environmental impact of fuels. The paper shows the state-of-the-art of the research and applications of bioprocesses to the petroleum field [it

Genetic toxicology of metal compounds: I. Induction of lambda prophage in E coli WP2/sub s/(lambda)

Energy Technology Data Exchange (ETDEWEB)

Rossman, T.G.; Molina, M.; Meyer, L.W.

1984-01-01

A number of metal compounds have been shown to be human carcinogens. Others, while not proven human carcinogens, are able to cause tumors in laboratory animals. Short-term bacterial assays for genotoxic effects have not been successful in predicting the carcinogenicity of metal compounds. The ability of some metal compounds to cause the induction of lambda prophage in E coli WP2/sub s/(lambda) is reported. By far the strongest inducing ability was observed with K/sub 2/CrO/sub 4/. With the exception of chromate, long-term exposures in a narrow, subtoxic dose range were required in order to demonstrate phage induction. A new microtiter assay for lambda prophage induction, which incorporates these features, is described. This system also was able to detect very small amounts of organic carcinogens.

Generation, detection and characterization of gas-phase transition metal aggregates and compounds

International Nuclear Information System (INIS)

Steimle, T.C.

1992-01-01

The goal of our research is to employ spectroscopic techniques to characterize the bound portions of the potential energy surface (PES) for chemical systems involving diatomic and triatomic transition metal molecules. The approach incorporates the generation and isolation of new metal compounds via supersonic laser ablation molecular beam techniques. Detection and characterization is achieved using high resolution dye laser induced fluorescence spectroscopy. A major objective is to produce information which can be compared to theoretical predictions and thereby provide guidelines and insight into the development of reaction models

Selective Oxidation of Lignin Model Compounds.

Science.gov (United States)

Gao, Ruili; Li, Yanding; Kim, Hoon; Mobley, Justin K; Ralph, John

2018-05-02

Lignin, the planet's most abundant renewable source of aromatic compounds, is difficult to degrade efficiently to welldefined aromatics. We developed a microwave-assisted catalytic Swern oxidation system using an easily prepared catalyst, MoO 2 Cl 2 (DMSO) 2 , and DMSO as the solvent and oxidant. It demonstrated high efficiency in transforming lignin model compounds containing the units and functional groups found in native lignins. The aromatic ring substituents strongly influenced the selectivity of β-ether phenolic dimer cleavage to generate sinapaldehyde and coniferaldehyde, monomers not usually produced by oxidative methods. Time-course studies on two key intermediates provided insight into the reaction pathway. Owing to the broad scope of this oxidation system and the insight gleaned with regard to its mechanism, this strategy could be adapted and applied in a general sense to the production of useful aromatic chemicals from phenolics and lignin. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Morphology and Orientation Selection of Non-metallic Inclusions in Electrified Molten Metal

Science.gov (United States)

Zhao, Z. C.; Qin, R. S.

2017-10-01

The effect of electric current on morphology and orientation selection of non-metallic inclusions in molten metal has been investigated using theoretical modeling and numerical calculation. Two geometric factors, namely the circularity ( fc ) and alignment ratio ( fe ) were introduced to describe the inclusions shape and configuration. Electric current free energy was calculated and the values were used to determine the thermodynamic preference between different microstructures. Electric current promotes the development of inclusion along the current direction by either expatiating directional growth or enhancing directional agglomeration. Reconfiguration of the inclusions to reduce the system electric resistance drives the phenomena. The morphology and orientation selection follow the routine to reduce electric free energy. The numerical results are in agreement with our experimental observations.

Absorption characteristics of compound heavy metals vanadium, chromium, and cadmium in water by emergent macrophytes and its combinations.

Science.gov (United States)

Lin, Hai; Liu, Junfei; Dong, Yingbo; Ren, Kaiqiang; Zhang, Yu

2018-04-20

The aim of the present study was to investigate three kinds of emergent macrophytes, i.e., Acorus calamus L., Phragmites communis Trin., and Alternanthera philoxeroides (Mart.) Griseb and their combination patterns on their removal efficiency of compound heavy metals (vanadium, chromium, and cadmium) from synthetic aqueous. The results showed that the optimal single-species for compound heavy metals removal was Acorus calamus L. and during experiment period, the average removal efficiency of V 5+ , Cr 6+ , and Cd 2+ was 52.4, 46.8, and 90.0%, respectively. Combination C (the quality ratio of Acorus calamus L., Phragmites communis Trin., and Alternanthera philoxeroides (Mart.) Griseb is 2:1:1) had the highest removal efficiency on compound heavy metals among three groups and the average removal efficiency of V 5+ , Cr 6+ , and Cd 2+ was 18.0, 70.0, and 95.1%, respectively. The highest efficiency of combination C on V 5+ removal was lower than single Alternanthera philoxeroides (Mart.) Griseb group; this may be an existing antagonism in different plants. Heavy metals of V 5+ , Cr 6+ , and Cd 2+ had an obviously positive effect on SOD, CAT, and POD of emergent macrophytes. From these results, we conclude that in a phytoremediation for the removal of compound heavy metals where V was dominated pollution in water, the use of Acorus calamus L. species rather than a mixture of several plants should be suggested. When heavy metal pollution was dominated by Cr and Cd, group C rather than a single plant species should be used.

Characteristics and possibilities of software tool for metal-oxide surge arresters selection

Directory of Open Access Journals (Sweden)

Đorđević Dragan

2012-01-01

Full Text Available This paper presents a procedure for the selection of metal-oxide surge arresters based on the instructions given in the Siemens and ABB catalogues, respecting their differences and the characteristics and possibilities of the software tool. The software tool was developed during the preparation of a Master's thesis titled, 'Automation of Metal-Oxide Surge Arresters Selection'. An example is presented of the selection of metal-oxide surge arresters using the developed software tool.

Effects of Ga substitution on the structural and magnetic properties of half metallic Fe{sub 2}MnSi Heusler compound

Energy Technology Data Exchange (ETDEWEB)

Pedro, S. S., E-mail: sandrapedro@uerj.br; Caraballo Vivas, R. J.; Andrade, V. M.; Cruz, C.; Paixão, L. S.; Contreras, C.; Costa-Soares, T.; Rocco, D. L.; Reis, M. S. [Instituto de Física, Universidade Federal Fluminense, Niterói-RJ (Brazil); Caldeira, L. [IF Sudeste MG, Campus Juiz de Fora - Núcleo de Física, Juiz de Fora-MG (Brazil); Coelho, A. A. [Instituto de Física Gleb Wataghin, Universidade Estadual de Campinas - Unicamp, Campinas-SP (Brazil); Carvalho, A. Magnus G. [Laboratório Nacional de Luz Sincrotron, CNPEM, Campinas-SP (Brazil)

2015-01-07

The so-called half-metallic magnets have been proposed as good candidates for spintronic applications due to the feature of exhibiting a hundred percent spin polarization at the Fermi level. Such materials follow the Slater-Pauling rule, which relates the magnetic moment with the valence electrons in the system. In this paper, we study the bulk polycrystalline half-metallic Fe{sub 2}MnSi Heusler compound replacing Si by Ga to determine how the Ga addition changes the magnetic, the structural, and the half-metal properties of this compound. The material does not follow the Slater-Pauling rule, probably due to a minor structural disorder degree in the system, but a linear dependence on the magnetic transition temperature with the valence electron number points to the half-metallic behavior of this compound.

Process for production of a metal hydride

Science.gov (United States)

Allen, Nathan Tait; Butterick, III, Robert; Chin, Arthur Achhing; Millar, Dean Michael; Molzahn, David Craig

2014-08-12

A process for production of a metal hydride compound MH.sub.x, wherein x is one or two and M is an alkali metal, Be or Mg. The process comprises combining a compound of formula (R.sup.1O).sub.xM with aluminum, hydrogen and at least one metal selected from among titanium, zirconium, hafnium, niobium, vanadium, tantalum and iron to produce a compound of formula MH.sub.x. R.sup.1 is phenyl or phenyl substituted by at least one alkyl or alkoxy group. A mole ratio of aluminum to (R.sup.1O).sub.xM is from 0.1:1 to 1:1. The catalyst is present at a level of at least 200 ppm based on weight of aluminum.

First-principles study of half-metallic properties in RbCaNZ (Z = O, S, and Se) quaternary Heusler compounds

Science.gov (United States)

Rezaei, S.; Ahmadian, F.

2018-06-01

On the basis of first principles calculations, the electronic structures and magnetic properties of quaternary Heusler alloys RbCaNZ (Z = O, S, and Se) were studied. The negative formation energies indicated that all these compounds were thermodynamically stable and thus may be experimentally synthesized at appropriate conditions in the future. The results showed that YI structure was the most favorable configuration among the three possible structures. All compounds were found to be half-metallic ferromagnets. The characteristic of energy bands and origin of half-metallicity were also verified. The total magnetic moments of RbCaNZ (Z = O, S, and Se) compounds were obtained 2μB per formula unit, which were in an agreement with Slater-Pauling rule (Mtot = 12 - Ztot). Half-metallicity was preserved at ranges of 5.06-8.36 Å, 5.96-8.81 Å, and 6.13-8.73 Å for RbCaNO, RbCaNS, and RbCaNSe compounds, respectively, which show that these quaternary Heusler compounds may be potential candidates in spintronic applications.

Selecting a Response in Task Switching: Testing a Model of Compound Cue Retrieval

Science.gov (United States)

Schneider, Darryl W.; Logan, Gordon D.

2009-01-01

How can a task-appropriate response be selected for an ambiguous target stimulus in task-switching situations? One answer is to use compound cue retrieval, whereby stimuli serve as joint retrieval cues to select a response from long-term memory. In the present study, the authors tested how well a model of compound cue retrieval could account for a…

Antioxidant and Antiradical Properties of Selected Flavonoids and Phenolic Compounds

Directory of Open Access Journals (Sweden)

Zübeyir Huyut

2017-01-01

Full Text Available Phenolic compounds and flavonoids are known by their antioxidant properties and one of the most important sources for humans is the diet. Due to the harmful effects of synthetic antioxidants such as BHA and BHT, natural novel antioxidants have become the focus of attention for protecting foods and beverages and reducing oxidative stress in vivo. In the current study, we investigated the total antioxidant, metal chelating, Fe3+ and Cu2+ reduction, and free radical scavenging activities of some phenolic and flavonoid compounds including malvin, oenin, ID-8, silychristin, callistephin, pelargonin, 3,4-dihydroxy-5-methoxybenzoic acid, 2,4,6-trihydroxybenzaldehyde, and arachidonoyl dopamine. The antioxidant properties of these compounds at different concentrations (10–30 μg/mL were compared with those of reference antioxidants such as BHA, BHT, α-tocopherol, and trolox. Each substance showed dose-dependent antioxidant activity. Furthermore, oenin, malvin, arachidonoyl dopamine, callistephin, silychristin, and 3,4-dihydroxy-5-methoxybenzoic acid exhibited more effective antioxidant activity than that observed for the reference antioxidants. These results suggest that these novel compounds may function to protect foods and medicines and to reduce oxidative stress in vivo.

Extraction of selected heavy metals using modified clays.

Science.gov (United States)

Krikorian, Nadine; Martin, Dean F

2005-01-01

In the present study, attapulgite, kaolinite, and montmorillonite KSF were modified using azeotropic distillation to condense 2-mercaptoethanol with the clay material. The resulting product was used as a coordinating agent to remove selected metal ions, e.g., copper(II), cadmium(II), silver(I), nickel(II), and lead(II) ions from standard aqueous solutions. Batch systems were used, and samples were shaken for two hours, and following filtration, metal content of the filtrate was measured by atomic absorption spectrometry. Without adjusting the pH, better than 90% of the metal ions could be removed.

Selective Recovery of Metals from Geothermal Brines

Energy Technology Data Exchange (ETDEWEB)

Ventura, Susanna [SRI International, Menlo Park, CA (United States); Bhamidi, Srinivas [SRI International, Menlo Park, CA (United States); Hornbostel, Marc [SRI International, Menlo Park, CA (United States); Nagar, Anoop [SRI International, Menlo Park, CA (United States); Perea, Elisabeth [SRI International, Menlo Park, CA (United States)

2016-12-16

The objective of this project was to determine the feasibility of developing a new generation of highly selective low-cost ion-exchange resins based on metal-ion imprinted polymers for the separation of metals from geothermal fluids. Expansion of geothermal energy production over the entire U.S. will involve exploitation of low-to-medium temperature thermal waters. Creating value streams from the recovery of critical and near-critical metals from these thermal waters will encourage geothermal expansion. Selective extraction of metals from geothermal fluids is needed to design a cost-effective process for the recovery of lithium and manganese-two near-critical metals with well-known application in the growing lithium battery industry. We have prepared new lithium- and manganese-imprinted polymers in the form of beads by crosslinking polymerization of a metal polymerizable chelate, where the metal acts as a template. Upon leaching out the metal template, the crosslinked polymer is expected to leave cavities defined by the ligand functional group with enhanced selectivity for binding the template metal. We have demonstrated that lithium- and manganese-imprinted polymer beads can be used as selective solid sorbents for the extraction of lithium and manganese from brines. The polymers were tested both in batch extractions and packed bed lab-scale columns at temperatures of 45-100°C. Lithium-imprinted polymers were found to have Li⁺ adsorption capacity as high as 2.8 mg Li⁺/g polymer at 45°C. Manganese-imprinted polymers were found to have a Mn²⁺ adsorption capacity of more than 23 mg Mn²⁺/g polymer at 75°C. The Li⁺ extraction efficiency of the Li-imprinted polymer was found to be more that 95% when a brine containing 390 ppm Li⁺, 410 ppm Na⁺, and 390 ppm K⁺ was passed through a packed bed of the polymer in a lab-scale column at 45°C. In brines containing 360 ppm Li

Soft X-ray spectroscopy of transition metal compounds: a theoretical perspective

International Nuclear Information System (INIS)

Bokarev, S.I.; Hilal, R.; Aziz, S.G.; Kühn, O.

2017-01-01

To date, X-ray spectroscopy has become a routine tool that can reveal highly local and element-specific information on the electronic structure of atoms in complex environments. Here, we report on the development of an efficient and versatile theoretical methodology for the treatment of soft X-ray spectra of transition metal compounds based on the multi-configurational self-consistent field electronic structure theory. A special focus is put on the L-edge photon-in/photon-out and photon-in/electron-out processes, i.e. X-ray absorption, resonant inelastic scattering, partial fluorescence yield, and photoelectron spectroscopy, all treated on the same theoretical footing. The investigated systems range from small prototypical coordination compounds and catalysts to aggregates of biomolecules.

Development of metallic system multi-composite materials for compound environment and corrosion monitoring technology

International Nuclear Information System (INIS)

Kiuchi, Kiyoshi

1996-01-01

For the structural materials used for the pressure boundary of nuclear power plants and others, the long term durability over several decades under the compound environment, in which the action of radiation and the corrosion and erosion in the environment of use are superposed, is demanded. To its controlling factors, the secular change of materials due to irradiation ageing and the chemical and physical properties of extreme compound environment are related complicatedly. In the first period of this research, the development of the corrosion-resistant alloys with the most excellent adaptability to environments was carried out by the combination of new alloy design and alloy manufacturing technology. In the second period, in order to heighten the adaptability as the pressure boundary materials between different compound environments, the creation of metallic system multi-composite materials has been advanced. Also corrosion monitoring technique is being developed. The stainless steel for water-cooled reactors, the wear and corrosion-resistant superalloy for reactor core, the corrosion-resistant alloy and the metallic refractory material for reprocessing nitric acid reaction vessels are reported. (K.I.)

Determination of Some Heavy Metals in Selected Beauty and ...

African Journals Online (AJOL)

Several epidemiologic studies have investigated the potential carcinogenicity of human exposure to heavy metals from diverse sources but few or none was on African black and beauty soaps. Hence, this study examines the presence of some heavy metals in selected African black and beauty soaps commonly used in ...

A study on compound contents for plastic injection molding products of metallic resin pigment

International Nuclear Information System (INIS)

Park, Young Whan; Kwak, Jae Seob; Lee, Gyu Sang

2016-01-01

Injection molding process is widely used for producing most plastic products. In order to make a metal-colored plastic product especially in modern luxury home alliances, metallic pigments which are mixed to a basic resin material for injection molding are available. However, the process control for the metal-colored plastic product is extremely difficult due to non-uniform melt flow of the metallic resin pigments. To improve the process efficiency, a rapid mold cooling method by a compressed cryogenic fluid and electricity mold are also proposed to decrease undesired compound contents within a molded plastic product. In this study, a quality of the metal-colored plastic product is evaluated with process parameters; injection speed, injection pressure, and pigment contents, and an influence of the rapid cooling and heating system is demonstrated

A study on compound contents for plastic injection molding products of metallic resin pigment

Energy Technology Data Exchange (ETDEWEB)

Park, Young Whan; Kwak, Jae Seob [Dept. of Mechanical Engineering, Pukyong National University, Busan (Korea, Republic of); Lee, Gyu Sang [Alliance Molding Engineering TeamLG Electronics Inc., Osan (Korea, Republic of)

2016-12-15

Injection molding process is widely used for producing most plastic products. In order to make a metal-colored plastic product especially in modern luxury home alliances, metallic pigments which are mixed to a basic resin material for injection molding are available. However, the process control for the metal-colored plastic product is extremely difficult due to non-uniform melt flow of the metallic resin pigments. To improve the process efficiency, a rapid mold cooling method by a compressed cryogenic fluid and electricity mold are also proposed to decrease undesired compound contents within a molded plastic product. In this study, a quality of the metal-colored plastic product is evaluated with process parameters; injection speed, injection pressure, and pigment contents, and an influence of the rapid cooling and heating system is demonstrated.

Phase associations and potential selective extraction methods for selected high-tech metals from ferromanganese nodules and crusts with siderophores

International Nuclear Information System (INIS)

Mohwinkel, Dennis; Kleint, Charlotte; Koschinsky, Andrea

2014-01-01

Highlights: • Phase associations of metals in marine Fe–Mn nodules and crusts were determined. • Selective leaching experiments with siderophore desferrioxamine B were conducted. • Siderophores selectively mobilize high-tech metals associated with Fe carrier phases. • Base metal liberation including Fe and Mn is limited. • Siderophores have promising potential for application in ore processing industries. - Abstract: Deep-sea ferromanganese deposits contain a wide range of economically important metals. Ferromanganese crusts and nodules represent an important future resource, since they not only contain base metals such as Mn, Ni, Co, Cu and Zn, but are also enriched in critical or rare high-technology elements such as Li, Mo, Nb, W, the rare earth elements and yttrium (REY). These metals could be extracted from nodules and crusts as a by-product to the base metal production. However, there are no proper separation techniques available that selectively extract certain metals out of the carrier phases. By sequential leaching, we demonstrated that, except for Li, which is present in an easily soluble form, all other high-tech metals enriched in ferromanganese nodules and crusts are largely associated with the Fe-oxyhydroxide phases and only to subordinate extents with Mn-oxide phases. Based on this fact, we conducted selective leaching experiments with the Fe-specific organic ligand desferrioxamine-B, a naturally occurring and ubiquitous siderophore. We showed by leaching of ferromanganese nodules and crusts with desferrioxamine-B that a significant and selective extraction of high-tech metals such as Li, Mo, Zr, Hf and Ta is possible, while other elements like Fe and the base metals Mn, Ni, Cu, Co and Zn are not extracted to large extents. The set of selectively extracted elements can be extended to Nb and W if Mn and carbonate phases are stripped from the bulk nodule or crust prior to the siderophore leach by e.g. a sequential leaching technique. This

THE RESEARCH OF THE AMOUNT OF HEAVY METALS AND NITROSO COMPOUNDS IN CONCENTRATED TOMATO PRODUCTS

Directory of Open Access Journals (Sweden)

V.V. Shutyuk

2016-12-01

Full Text Available The constant selling race results in need for improving the quality of nutrition products among in-house food and pharmaceutical processing industries, which is an all-important key to success on the consumer market. This requires constant improvement of the product producing technologies. The topical problem of quality is the presence of heavy metals and nitroso compounds in the products. The research aimed at studying the changes in the heavy metal concentration levels (including Zn, Cu, Pb in tomato products at their thickening has been conducted at the national University of Food Technologies. On the basis of the received results the relationship between the lead, copper, zinc, nitrosocompounds and the solid substances’ amount has been established. The conducted research allowed us to ascertain the fact that the amount of heavy metals and nitroso compounds in raw materials for the concentrated tomato products to be ofhigh quality must not exceed the values of 18…35 % of the limiting concentration.

Photoacidic and Photobasic Behavior of Transition Metal Compounds with Carboxylic Acid Group(s)

Energy Technology Data Exchange (ETDEWEB)

O’Donnell, Ryan M. [Department of Chemistry, University of North Carolina at Chapel Hill, Chapel Hill, North Carolina 27599, United States; Sampaio, Renato N. [Department of Chemistry, University of North Carolina at Chapel Hill, Chapel Hill, North Carolina 27599, United States; Li, Guocan [Department of Chemistry, University of North Carolina at Chapel Hill, Chapel Hill, North Carolina 27599, United States; Johansson, Patrik G. [Department of Chemistry, University of North Carolina at Chapel Hill, Chapel Hill, North Carolina 27599, United States; Ward, Cassandra L. [Department of Chemistry, University of North Carolina at Chapel Hill, Chapel Hill, North Carolina 27599, United States; Meyer, Gerald J. [Department of Chemistry, University of North Carolina at Chapel Hill, Chapel Hill, North Carolina 27599, United States

2016-03-10

Excited state proton transfer studies of six Ru polypyridyl compounds with carboxylic acid/carboxylate group(s) revealed that some were photoacids and some were photobases. The compounds [Ru^II(btfmb)₂(LL)]²⁺, [Ru^II(dtb)2(LL)]2+, and [RuII(bpy)2(LL)]2+, where bpy is 2,2'-bipyridine, btfmb is 4,4'-(CF₃)₂-bpy, and dtb is 4,4'-((CH₃)₃C)₂-bpy, and LL is either dcb = 4,4'-(CO₂H)₂-bpy or mcb = 4-(CO₂H),4'-(CO2Et)-2,2'-bpy, were synthesized and characterized. The compounds exhibited intense metal-to-ligand charge-transfer (MLCT) absorption bands in the visible region and room temperature photoluminescence (PL) with long τ > 100 ns excited state lifetimes. The mcb compounds had very similar ground state pKa’s of 2.31 ± 0.07, and their characterization enabled accurate determination of the two pK_a values for the commonly utilized dcb ligand, pK_a1 = 2.1 ± 0.1 and pKa2 = 3.0 ± 0.2. Compounds with the btfmb ligand were photoacidic, and the other compounds were photobasic. Transient absorption spectra indicated that btfmb compounds displayed a [Ru^III(btfmb–)L₂]^2+* localized excited state and a [Ru^III(dcb–)L₂]^2+* formulation for all the other excited states. Time dependent PL spectral shifts provided the first kinetic data for excited state proton transfer in a transition metal compound. PL titrations, thermochemical cycles, and kinetic analysis (for the mcb compounds) provided self-consistent pK_a* values. The ability to make a single ionizable group photobasic or photoacidic through ligand design was unprecedented and was understood based on the orientation of the lowest-lying MLCT excited state dipole relative to the ligand that contained the carboxylic acid group(s).

Carbon based secondary compounds do not provide protection against heavy metal road pollutants in epiphytic macrolichens.

Science.gov (United States)

Gauslaa, Yngvar; Yemets, Olena A; Asplund, Johan; Solhaug, Knut Asbjørn

2016-01-15

Lichens are useful monitoring organisms for heavy metal pollution. They are high in carbon based secondary compounds (CBSCs) among which some may chelate heavy metals and thus increase metal accumulation. This study quantifies CBSCs in four epiphytic lichens transplanted for 6months on stands along transects from a highway in southern Norway to search for relationships between concentrations of heavy metals and CBSCs along a gradient in heavy metal pollutants. Viability parameters and concentrations of 21 elements including nutrients and heavy metals in these lichen samples were reported in a separate paper. Medullary CBSCs in fruticose lichens (Ramalina farinacea, Usnea dasypoga) were reduced in the most polluted sites, but not in foliose ones (Parmelia sulcata, Lobaria pulmonaria), whereas cortical CBSC did not change with distance from the road in any species. Strong positive correlations only occurred between the major medullary compound stictic acid present in L. pulmonaria and most heavy metals, consistent with a chelating role of stictic acid, but not of other studied CBSCs or in other species. However, heavy metal chelating did not protect L. pulmonaria against damage because this species experienced the strongest reduction in viability in the polluted sites. CBSCs with an accumulation potential for heavy metals should be quantified in lichen biomonitoring studies of heavy metals because they, like stictic acid, could overshadow pollutant inputs in some species rendering biomonitoring data less useful. In the two fruticose lichen species, CBSCs decreased with increasing heavy metal concentration, probably because heavy metal exposure impaired secondary metabolism. Thus, we found no support for a heavy metal protection role of any CBSCs in studied epiphytic lichens. No intraspecific relationships occurred between CBSCs versus N or C/N-ratio. Interspecifically, medullary CBSCs decreased and cortical CBSCs increased with increasing C/N-ratio. Copyright © 2015

Thiacalix[4]arene derivatives as extractants for metal ions in aqueous solutions: Application to the selective facilitated transport of Ag(I)

Energy Technology Data Exchange (ETDEWEB)

Zaghbani, Asma [Laboratoire Eau et Technologies Membranaires, CERTE, BP 273, 8020 Soliman (Tunisia); Fontas, Claudia [Department of Chemistry, University of Girona, 17071 Girona (Spain)], E-mail: claudia.fontas@udg.edu; Hidalgo, Manuela [Department of Chemistry, University of Girona, 17071 Girona (Spain); Tayeb, Rafik; Dhahbi, Mahmoud [Laboratoire Eau et Technologies Membranaires, CERTE, BP 273, 8020 Soliman (Tunisia); Vocanson, Francis; Lamartine, Roger [Universite de Lyon, Lyon, F-69003 (France); Universite Lyon 1, Villeurbanne, F-69622 (France); CNRS, UMR 5246, ICBMS, equipe CSAp, 43 boulevard du 11 novembre 1918, Villeurbanne, F-69622 (France); Seta, Patrick [Institut Europeen des Membranes, UMR CNRS 5635, 1919 route de Mende, 34293 Montpellier (France)

2008-07-01

The complexation abilities of different thiacalix[4]arene derivatives towards some rare earth metal ions, metallic pollutants, and noble metals have been investigated in liquid-liquid experiments. Thiacalix[4]arene dissolved in chloroform effectively extracts Pd(II) (in acidic chloride media) and also Ag(I), Cd(II), Sm(III) and Ce(III), all buffered at pH 6 or 8. The modification of this compound to form an amide derivative results in an effective extraction of noble metals, ranked according to Au(III) > Pd(II) > Pt(IV) > Ag(I). Moreover, a supported liquid membrane system for silver transport has been developed based on thiacalix[4]arene dissolved in NPOE, and parameters affecting its efficiency have been investigated, such as the stripping composition and the pH of the feed solution. Finally, the selectivity of the membrane system has been evaluated by using as feed sources mixtures of silver and other metal ion000.

Comparative Study of Heavy Metals in Soil and Selected Medicinal Plants

Directory of Open Access Journals (Sweden)

Afzal Shah

2013-01-01

Full Text Available Essential and nonessential heavy metals like iron (Fe, nickel (Ni, manganese (Mn, zinc (Zn, copper (Cu, cadmium (Cd, chromium (Cr, and lead (Pb were analyzed in four selected medicinal plants such as Capparis spinosa, Peganum harmala, Rhazya stricta, and Tamarix articulata by flame atomic absorption spectrophotometer (FAAS. These medicinal plants are extensively used as traditional medicine for treatment of various ailments by local physicians in the area from where these plants were collected. The concentration level of heavy metals in the selected plants was found in the decreasing order as Fe > Zn > Mn > Cu > Ni > Cr > Cd > Pb. The results revealed that the selected medicinal plants accumulate these elements at different concentrations. Monitoring such medicinal plants for heavy metals concentration is of great importance for physicians, health planners, health care professionals, and policymakers in protecting the public from the adverse effects of these heavy metals.

μSR-studies of magnetic properties of metallic rare earth compounds

International Nuclear Information System (INIS)

Asch, L.; Kalvius, G.M.; Chappert, J.; Yaouanc, A.; Hartmann, O.; Karlsson, E.; Wappling, R.

1984-01-01

Positive muons can probe the magnitude and the time dependence of the magnetic field at interstitial sites in condensed matter. Thus the relatively new techniques of muons spin rotation and muon spin relaxation have become unique tools for studying magnetism. After a brief introduction into the experimental method we then discuss measurements on the elemental rare earth metals and on intermetallic compounds, in particular on the cubic Laves phases REAl 2

Effect of metal selection and porcelain firing on the marginal accuracy of titanium-based metal ceramic restorations.

Science.gov (United States)

Shokry, Tamer E; Attia, Mazen; Mosleh, Ihab; Elhosary, Mohamed; Hamza, Tamer; Shen, Chiayi

2010-01-01

Titanium is the most biocompatible metal used for dental casting; however, there is concern about its marginal accuracy after porcelain application since this aspect has direct influence on marginal fit. The purpose of this study was to determine the effect that metal selection and the porcelain firing procedure have on the marginal accuracy of metal ceramic prostheses. Cast CP Ti, milled CP Ti, cast Ti-6Al-7Nb, and cast Ni-Cr copings (n=5) were fired with compatible porcelains (Triceram for titanium-based metals and VITA VMK 95 for Ni-Cr alloy). The Ni-Cr alloy fired with its porcelain served as the control. Photographs of metal copings placed on a master die were made. Marginal discrepancy was determined on the photographs using an image processing program at 8 predetermined locations before airborne-particle abrasion for porcelain application, after firing of the opaque layer, and after firing of the dentin layer. Repeated-measures 2-way ANOVA was used to investigate the effect of metal selection and firing stage, and paired t tests were used to determine the effect of each firing stage within each material group (alpha=.05). ANOVA showed that both metal selection and firing stage significantly influenced the measured marginal discrepancy (Pcast Ti-6Al-7Nb alloy (P=.003). Titanium copings fabricated by CAD/CAM demonstrated the least marginal discrepancy among all groups, while the base metal (Ni-Cr) groups exhibited the most discrepancy of all groups tested. Copyright 2010 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Bitropic D3 Dopamine Receptor Selective Compounds as Potential Antipsychotics.

Science.gov (United States)

Luedtke, Robert R; Rangel-Barajas, Claudia; Malik, Mahinder; Reichert, David E; Mach, R H

2015-01-01

Neuropsychiatric disorders represent a substantial social and health care issue. The National Institutes of Health estimates that greater than 2 million adults suffer from neuropsychiatric disorders in the USA. These individuals experience symptoms that can include auditory hallucinations, delusions, unrealistic beliefs and cognitive dysfunction. Although antipsychotic medications are available, suboptimal therapeutic responses are observed for approximately one-third of patients. Therefore, there is still a need to explore new pharmacotherapeutic strategies for the treatment of neuropsychiatric disorders. Many of the medications that are used clinically to treat neuropsychiatric disorders have a pharmacological profile that includes being an antagonist at D2-like (D2, D3 and D4) dopamine receptor subtypes. However, dopamine receptor subtypes are involved in a variety of neuronal circuits that include movement coordination, cognition, emotion, affect, memory and the regulation of prolactin. Consequently, antagonism at D2-like receptors can also contribute to some of the adverse side effects associated with the long-term use of antipsychotics including the a) adverse extrapyramidal symptoms associated with the use of typical antipsychotics and b) metabolic side effects (weight gain, hyperglycemia, increased risk of diabetes mellitus, dyslipidemia and gynecomastia) associated with atypical antipsychotic use. Preclinical studies suggest that D3 versus D2 dopamine receptor selective compounds might represent an alternative strategy for the treatment of the symptoms of schizophrenia. In this review we discuss a) how bitropic Nphenylpiperazine D3 dopamine receptor selective compounds have been developed by modification of the primary (orthosteric) and secondary (allosteric or modulatory) pharmacophores to optimize D3 receptor affinity and D2/D3 binding selectivity ratios and b) the functional selectivity of these compounds. Examples of how these compounds might be

Genetic toxicology of metal compounds. I. Induction of lambda prophage in E coli WP2/sub s/(lambda)

Energy Technology Data Exchange (ETDEWEB)

Rossman, T.G.; Molina, M.; Meyer, L.W.

1984-01-01

A number of metal compounds have been shown to be human carcinogens. Others, while not proven human carcinogens, are able to cause tumors in laboratory animals. Short-term bacterial assays for genotoxic effects have not been successful in predicting the carcinogenicity of metal compounds. The authors report here the ability of some metal compounds to cause the induction of lambda prophage in E coli WP2/sub s/(lambda). By far the strongest inducing ability was observed with K/sub 2/CrO/sub 4/, followed by Pb(NO/sub 3/)/sub 2/ > Ni(OOCCH/sub 3/)/sub 2/ > CrCl/sub 2/ > NaWO/sub 4/ > Na/sub 2/MoO/sub 4/ > KMnO/sub 4/. With the exception of chromate, long-term exposures in a narrow, subtoxic dose range were required in order to demonstrate phage induction. A new microtiter assay for lambda prophage induction, which incorporates these features, is described. This system also was able to detect very small amounts of organic carcinogens.

Selective metal pattern formation and its EMI shielding efficiency

International Nuclear Information System (INIS)

Lee, Ho-Chul; Kim, Jin-Young; Noh, Chang-Ho; Song, Ki Yong; Cho, Sung-Heon

2006-01-01

A novel method for selective metal pattern formation by using an enhanced life-time of photoexcited electron-hole pairs in bilayer thin film of amorphous titanium dioxide and hole-scavenger-containing poly(vinyl alcohol) was proposed. By UV-irradiation through photomask on the bilayer film, the photodefined image of photoelectrons could be easily and simply produced, consequently resulting in selective palladium (Pd) catalyst deposition by reduction. The successive electrolessplating on Pd catalysts and electroplating on electrolessplated pattern were possible. Furthermore, the electromagnetic interference shielding efficiencies of the metal mesh patterns with various characteristic length scales of line width and thickness were investigated

Interaction of intermetallic compounds formed by rare earths, scandium, yttrium and 3d-transition metals, with gaseous ammonia

International Nuclear Information System (INIS)

Shilkin, S.P.; Volkova, L.S.

1992-01-01

Interaction of the RT n intermetallic compounds, where R Sc, Y, rare earths, T = Fe, Co, Ni; n = 2,3,5, with gaseous ammonia under pressure of 1MPa and at temperatures of 293, 723 and 798 K is studied. It is established on the basis of roentgenographic studied, chemical analysis data, X-ray photoelectron spectroscopy and specific surface measurements that metallic matrixes of intermetallides decompose into nitrides and transition metal phases at temperatures of 723 and 798 K under effect of ammonia and independent of structural types of the source materials; partial or complete decomposition of intermetallides through ammonia with formation of transition metal mixture, binary hydrides and nitrides of the most electropositive metal the above systems occurs at the temperature of 293 K depending on the heat of the source compounds and their tendency to decomposition under ammonia effect

Optimal selection of biochars for remediating metals ...

Science.gov (United States)

Approximately 500,000 abandoned mines across the U.S. pose a considerable, pervasive risk to human health and the environment due to possible exposure to the residuals of heavy metal extraction. Historically, a variety of chemical and biological methods have been used to reduce the bioavailability of the metals at mine sites. Biochar with its potential to complex and immobilize heavy metals, is an emerging alternative for reducing bioavailability. Furthermore, biochar has been reported to improve soil conditions for plant growth and can be used for promoting the establishment of a soil-stabilizing native plant community to reduce offsite movement of metal-laden waste materials. Because biochar properties depend upon feedstock selection, pyrolysis production conditions, and activation procedures used, they can be designed to meet specific remediation needs. As a result biochar with specific properties can be produced to correspond to specific soil remediation situations. However, techniques are needed to optimally match biochar characteristics with metals contaminated soils to effectively reduce metal bioavailability. Here we present experimental results used to develop a generalized method for evaluating the ability of biochar to reduce metals in mine spoil soil from an abandoned Cu and Zn mine. Thirty-eight biochars were produced from approximately 20 different feedstocks and produced via slow pyrolysis or gasification, and were allowed to react with a f

EDITORIAL: New materials with high spin polarization: half-metallic Heusler compounds

Science.gov (United States)

Felser, Claudia; Hillebrands, Burkard

2007-03-01

The development of magnetic Heusler compounds, specifically designed as materials for spintronic applications, has made tremendous progress in the very recent past [1-21]. Heusler compounds can be made as half-metals, showing a high spin polarization of the conduction electrons of up to 100% [1]. These materials are exceptionally well suited for applications in magnetic tunnel junctions acting, for example, as sensors for magnetic fields. The tunnelling magneto-resistance (TMR) effect is the relative change in the electrical resistance upon application of a small magnetic field. Tunnel junctions with a TMR effect of 580% at 4 K were reported by the group of Miyazaki and Ando [1], consisting of two Co2MnSi Heusler electrodes. High Curie temperatures were found in Co2 Heusler compounds with values up to 1120 K in Co2FeSi [2]. The latest results are for a TMR device made from the Co2FeAl0.5Si0.5 Heusler compound and working at room temperature with a TMR effect of 174% [3]. The first significant magneto-resistance effect was discovered in Co2Cr0.6Fe0.4Al (CCFA) in Mainz [4]. With the classical Heusler compound CCFA as one electrode, the record TMR effect at 4 K is 240% [5]. Positive and negative TMR values at room temperature utilizing magnetic tunnel junctions with one Heusler compound electrode render magnetic logic possible [6]. Research efforts exist, in particular, in Japan and in Germany. The status of research as of winter 2005 was compiled in a recent special volume of Journal of Physics D: Applied Physics [7-20]. Since then specific progress has been made on the issues of (i) new advanced Heusler materials, (ii) advanced characterization, and (iii) advanced devices using the new materials. In Germany, the Mainz and Kaiserslautern based Research Unit 559 `New Materials with High Spin Polarization', funded since 2004 by the Deutsche Forschungsgemeinschaft, is a basic science approach to Heusler compounds, and it addresses the first two topics in particular

Rapid, Selective Heavy Metal Removal from Water by a Metal-Organic Framework/Polydopamine Composite.

Science.gov (United States)

Sun, Daniel T; Peng, Li; Reeder, Washington S; Moosavi, Seyed Mohamad; Tiana, Davide; Britt, David K; Oveisi, Emad; Queen, Wendy L

2018-03-28

Drinking water contamination with heavy metals, particularly lead, is a persistent problem worldwide with grave public health consequences. Existing purification methods often cannot address this problem quickly and economically. Here we report a cheap, water stable metal-organic framework/polymer composite, Fe-BTC/PDA, that exhibits rapid, selective removal of large quantities of heavy metals, such as Pb 2+ and Hg 2+ , from real world water samples. In this work, Fe-BTC is treated with dopamine, which undergoes a spontaneous polymerization to polydopamine (PDA) within its pores via the Fe 3+ open metal sites. The PDA, pinned on the internal MOF surface, gains extrinsic porosity, resulting in a composite that binds up to 1634 mg of Hg 2+ and 394 mg of Pb 2+ per gram of composite and removes more than 99.8% of these ions from a 1 ppm solution, yielding drinkable levels in seconds. Further, the composite properties are well-maintained in river and seawater samples spiked with only trace amounts of lead, illustrating unprecedented selectivity. Remarkably, no significant uptake of competing metal ions is observed even when interferents, such as Na + , are present at concentrations up to 14 000 times that of Pb 2+ . The material is further shown to be resistant to fouling when tested in high concentrations of common organic interferents, like humic acid, and is fully regenerable over many cycles.

Intra-molecular selectivity of muonium towards chlorinated aromatic compounds

International Nuclear Information System (INIS)

Venkateswaran, K.; Stadlbauer, J.M.; Laing, M.E.; Klugkist, J.; Chong, D.P.; Porter, G.B.; Walker, D.C.

1994-01-01

Muon resonance studies show that muonium atoms (Mu) in ethanol add selectively to certain C-sites of aromatic compounds containing -Cl and -OH substituents. The sites chosen seem to be those carrying the lowest electron density. This helps to characterize Mu as a nucleophile in addition reactions and, in this respect, Mu differs from ordinary H-atoms. The study shows no apparent inter-molecular selectivity between a pair of aromatic solutes in an equimolar mixture, but strong intra-molecular selectivity in an ether composed of those two aromatic rings. This difference between intra- and inter-molecular selectivity is interpreted as kinetic in origin - arising from the 'caging effect' of the solvent and peculiar to reactions close to the diffusion-controlled limit. (orig.)

NMR in metal cluster compounds compared to glasses

International Nuclear Information System (INIS)

Staveren, M.P.J. van; Brom, H.B.; Jongh, L.J. de; Schmid, G.

1991-01-01

The field and temperature dependence of the 31 P nuclear spin lattice relaxation rate in the metal cluster compound Ru 55 (P(t-Bu) 3 ) 12 Cl 20 follows a power law: 1/T 1 ∝ T n B -m , with n = 1.5 ± 0.1 at 3.25 T and n = 1.3 ± 0.1 at 6.45 T; m ≅ 1.4. Such dependences have so far only been observed in inorganic glasses and been attributed to two level systems. The correspondence suggests that the relaxation rate is due to interaction of the P-nuclear moment with electronic spins of stochastically moving charge carriers, which are thought to be responsible for the electrical conductivity through hopping between neigboring cluster molecules. (orig.)

The metal-driven biogeochemistry of gaseous compounds in the environment

CERN Document Server

Kroneck, Peter MH

2014-01-01

MILS-14 provides a most up-to-date view of the exciting biogeochemistry of gases in our environment as driven mostly by microorganisms. These employ a machinery of sophisticated metalloenzymes, where especially transition metals (such as Fe, Ni, Cu, Mo, W) play a fundamental role, that is, in the activation, transformation and syntheses of gases like dihydrogen, methane, carbon monoxide, acetylene and those of the biological nitrogen and sulfur cycles. The Metal-Driven Biogeochemistry of Gaseous Compounds in the Environment is a vibrant research area based mainly on structural and microbial biology, inorganic biological chemistry and environmental biochemistry. All this is covered in an authoritative manner in 11 stimulating chapters, written by 26 internationally recognized experts and supported by nearly 1200 references, informative tables and about 100 illustrations (two thirds in color). MILS-14 also provides excellent information for teaching. Peter M. H. Kroneck is a bioinorganic chemist who is explorin...

Electron and nuclear magnetic resonances in compounds and metallic hydrides

International Nuclear Information System (INIS)

Brasil Filho, N.

1985-11-01

Proton pulsed Nuclear Magnetic Resonance measurements were performed on the metallic hydrides ZrCr 2 H x (x = 2, 3, 4) and ZrV 2 H y (y = 2, 3, 4, 5) as a function of temperature between 180 and 400K. The ultimate aim was the investigation of the relaxation mechanisms in these systems by means of the measurement of both the proton ( 1 H) spin-lattice (T 1 ) and spin-spin (T 2 ) relaxation times and to use these data to obtain information about the diffusive motion of the hydrogen atoms. The diffusional activation energies, the jump frequencies and the Korringa constant, C k , related with the conduction electron contribution to the 1 H relaxation were determined for the above hydrides as a function of hydrogen concentration. Our results were analysed in terms of the relaxation models described by Bloembergen, Purcell and Pound (BPP model) and by Torrey. The Korringa type relaxation due to the conduction electrons in metallic systems was also used to interpret the experimental results. We also present the Electron Paramagnetic Ressonance (EPR) study of Gd 3+ , Nd 3+ and Er 3+ ions as impurities in several AB 3 intermetallic compounds where A = LA, Ce, Y, Sc, Th, Zr and B = Rh, Ir, Pt. The results were analysed in terms of the multiband model previously suggested to explain the behaviour of the resonance parameter in AB 2 Laves Phase compounds. (author) [pt

Efficient and selective α-bromination of carbonyl compounds with N-bromosuccinimide under microwave

KAUST Repository

Guan, Xiao-Yu

2014-02-07

A highly efficient method for the synthesis of α-halocarbonyl compounds has been achieved via selective monobromination of aromatic and aliphatic carbonyl compounds with N-bromosuccinimide catalyzed by p-toluenesulfonic acid under microwave irradiation within 30 min.

Efficient and selective α-bromination of carbonyl compounds with N-bromosuccinimide under microwave

KAUST Repository

Guan, Xiao-Yu; Al-Misba'a, Zahra; Huang, Kuo-Wei

2014-01-01

A highly efficient method for the synthesis of α-halocarbonyl compounds has been achieved via selective monobromination of aromatic and aliphatic carbonyl compounds with N-bromosuccinimide catalyzed by p-toluenesulfonic acid under microwave irradiation within 30 min.

Electronic computer prediction of properties of binary refractory transition metal compounds on the base of their simplificated electronic structure

International Nuclear Information System (INIS)

Kutolin, S.A.; Kotyukov, V.I.

1979-01-01

An attempt is made to obtain calculation equations of macroscopic physico-chemical properties of transition metal refractory compounds (density, melting temperature, Debye characteristic temperature, microhardness, standard formation enthalpy, thermo-emf) using the method of the regression analysis. Apart from the compound composition the argument of the regression equation is the distribution of electron bands of d-transition metals, created by the energy electron distribution in the simplified zone structure of transition metals and approximated by Chebishev polynoms, by the position of Fermi energy on the map of distribution of electron band energy depending upon the value of quasi-impulse, multiple to the first, second and third Brillouin zone for transition metals. The maximum relative error of the regressions obtained as compared with the literary data is 15-20 rel.%

Isolation and characterization of iron chelators from turmeric (Curcuma longa): selective metal binding by curcuminoids.

Science.gov (United States)

Messner, Donald J; Surrago, Christine; Fiordalisi, Celia; Chung, Wing Yin; Kowdley, Kris V

2017-10-01

Iron overload disorders may be treated by chelation therapy. This study describes a novel method for isolating iron chelators from complex mixtures including plant extracts. We demonstrate the one-step isolation of curcuminoids from turmeric, the medicinal food spice derived from Curcuma longa. The method uses iron-nitrilotriacetic acid (NTA)-agarose, to which curcumin binds rapidly, specifically, and reversibly. Curcumin, demethoxycurcumin, and bisdemethoxycurcumin each bound iron-NTA-agarose with comparable affinities and a stoichiometry near 1. Analyses of binding efficiencies and purity demonstrated that curcuminoids comprise the primary iron binding compounds recovered from a crude turmeric extract. Competition of curcuminoid binding to the iron resin was used to characterize the metal binding site on curcumin and to detect iron binding by added chelators. Curcumin-Iron-NTA-agarose binding was inhibited by other metals with relative potency: (>90% inhibition) Cu 2+  ~ Al 3+  > Zn 2+  ≥ Ca 2+  ~ Mg 2+  ~ Mn 2+ (80% by addition of iron to the media; uptake was completely restored by desferoxamine. Ranking of metals by relative potencies for blocking curcumin uptake agreed with their relative potencies in blocking curcumin binding to iron-NTA-agarose. We conclude that curcumin can selectively bind toxic metals including iron in a physiological setting, and propose inhibition of curcumin binding to iron-NTA-agarose for iron chelator screening.

Electron beam selectively seals porous metal filters

Science.gov (United States)

Snyder, J. A.; Tulisiak, G.

1968-01-01

Electron beam welding selectively seals the outer surfaces of porous metal filters and impedances used in fluid flow systems. The outer surface can be sealed by melting a thin outer layer of the porous material with an electron beam so that the melted material fills all surface pores.

C- and N-Metalated Nitriles: The Relationship between Structure and Selectivity.

Science.gov (United States)

Yang, Xun; Fleming, Fraser F

2017-10-17

Metalated nitriles are exceptional nucleophiles capable of forging highly hindered stereocenters in cases where enolates are unreactive. The excellent nucleophilicity emanates from the powerful inductive stabilization of adjacent negative charge by the nitrile, which has a miniscule steric demand. Inductive stabilization is the key to understanding the reactivity of metalated nitriles because this permits a continuum of structures that range from N-metalated ketenimines to nitrile anions. Solution and solid-state analyses reveal two different metal coordination sites, the formally anionic carbon and the nitrile nitrogen, with the site of metalation depending intimately on the solvent, counterion, temperature, and ligands. The most commonly encountered structures, C- and N-metalated nitriles, have either sp 3 or sp 2 hybridization at the nucleophilic carbon, which essentially translates into two distinct organometallic species with similar but nonidentical stereoselectivity, regioselectivity, and reactivity preferences. The hybridization differences are particularly important in S N i displacements of cyclic nitriles because the orbital orientations create very precise trajectories that control the cyclization selectivity. Harnessing the orbital differences between C- and N-metalated nitriles allows selective cyclization to afford nitrile-containing cis- or trans-hydrindanes, decalins, or bicyclo[5.4.0]undecanes. Similar orbital constraints favor preferential S N i displacements with allylic electrophiles on sp 3 centers over sp 2 centers. The strategy permits stereoselective displacements on secondary centers to set contiguous tertiary and quaternary stereocenters or even contiguous vicinal quaternary centers. Stereoselective alkylations of acyclic nitriles are inherently more challenging because of the difficulty in creating steric differentiation in a dynamic system with rotatable bonds. However, judicious substituent placement of vicinal dimethyl groups and a

Selective propene oxidation on mixed metal oxide catalysts

International Nuclear Information System (INIS)

James, David William

2002-01-01

Selective catalytic oxidation processes represent a large segment of the modern chemical industry and a major application of these is the selective partial oxidation of propene to produce acrolein. Mixed metal oxide catalysts are particularly effective in promoting this reaction, and the two primary candidates for the industrial process are based on iron antimonate and bismuth molybdate. Some debate exists in the literature regarding the operation of these materials and the roles of their catalytic components. In particular, iron antimonate catalysts containing excess antimony are known to be highly selective towards acrolein, and a variety of proposals for the enhanced selectivity of such materials have been given. The aim of this work was to provide a direct comparison between the behaviour of bismuth molybdate and iron antimonate catalysts, with additional emphasis being placed on the component single oxide phases of the latter. Studies were also extended to other antimonate-based catalysts, including cobalt antimonate and vanadium antimonate. Reactivity measurements were made using a continuous flow microreactor, which was used in conjunction with a variety of characterisation techniques to determine relationships between the catalytic behaviour and the properties of the materials. The ratio of Fe/Sb in the iron antimonate catalyst affects the reactivity of the system under steady state conditions, with additional iron beyond the stoichiometric value being detrimental to the acrolein selectivity, while extra antimony provides a means of enhancing the selectivity by decreasing acrolein combustion. Studies on the single antimony oxides of iron antimonate have shown a similarity between the reactivity of 'Sb 2 O 5 ' and FeSbO 4 , and a significant difference between these and the Sb 2 O 3 and Sb 2 O 4 phases, implying that the mixed oxide catalyst has a surface mainly comprised of Sb 5+ . The lack of reactivity of Sb 2 O 4 implies a similarity of the surface with

Geochemical investigations into the retention of reactive carbon compounds for toxic heavy metals. Final report; Geochemische Untersuchungen zur Retention von reaktiven Kohlenstoffverbindungen fuer toxische Schwermetalle. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Kupsch, H.; Mansel, A.; Crustewitz, C.

2003-03-01

The composition, reactivity and stability of reactive organic carbon compounds adsorbed on geogenic matrices was investigated. The surface deposits of NOM and its dependence on geochemical parameters was investigated in selected geomatrices. The retention of toxic heavy metals on these surface deposits of NOM was investigated in consideration of the presence of hydroxy species and inorganic ligands. The investigations of the reactivity of the NOM species requires analyses of these compounds and of the heavy metals in the ultratracer region. This was possible by means of radiochemical methods that were further developed in the context of this project. Radioactive labeling of identified reactive carbon compounds, e.g. with radioactive iodine, on the one hand, and the use of radioactive Cu, Pb, Hg isotopes on the other hand enabled speciation analyses in the binary systems (heavy metal + geomatrix, heavy metal + reactive carbon compounds, reactive carbon compounds + geomatrix) and especially in the ternary system (heavy metal + geomatrix + reactive carbon compounds) in defined conditions. The special labelling techniques were a precondition for distribution measurements in the near-natural, low concentration range. (orig.) [German] Ziel des Projektes war es, mit der vorhandenen Analytik und Expertise die Zusammensetzung, die Reaktivitaet und die Stabilitaet der auf den geogenen Matrizes sorbierten reaktiven organischen Kohlenstoffverbindungen und die damit verbundenen Stoffumsaetze aufzuklaeren. An ausgewaehlten Geomatrizes wurde die Ausbildung von Oberflaechendepositen des NOM und deren Abhaengigkeit gegenueber geochemischen Parametern untersucht. Unter der Beruecksichtigung der Gegenwart von Hydroxyspezies und anorganischen Liganden wurde die Retention toxischer Schwermetalle an diesen Oberflaechendepositen des NOM untersucht. Die Untersuchungen zur Reaktivitaet der NOM-Spezies setzt eine Analytik dieser Verbindungen und der Schwermetalle im Ultraspurenbereich

Magnetism in ordered metallic perovskite compound GdPd3BxC1-x

International Nuclear Information System (INIS)

Pandey, Abhishek; Mazumdar, Chandan; Ranganathan, R.; Dattagupta, S.

2009-01-01

We report results of dc-magnetization, ac-susceptibility and magnetoresistance measurements on crystalline metallic-perovskite compounds GdPd 3 B x C 1-x (x=0.25, 0.50, 0.75 and 1.00) and the parent cubic compound GdPd 3 . The interest in these materials stems from the observation of negative temperature coefficient of resistance and negative thermal expansion in some of the members of this series. In the present study, we show that by substitution of non-magnetic elements, boron and carbon, the nature of the magnetic interaction can be varied from dominating ferromagnetic to antiferromagnetic and finally to a canted magnetic structure without altering the crystal symmetry of the compounds. The variation of magnetic interaction by modifying the lattice parameter resembles Ruderman-Kittel-Kasuya-Yosida (RKKY) oscillations.

New Proton-Ionizable, Calixarene-Based Ligands for Selective Metal Ion Separations

Energy Technology Data Exchange (ETDEWEB)

Bartsch, Richard A.

2012-06-04

The project objective was the discovery of new ligands for performing metal ion separations. The research effort entailed the preparation of new metal ion complexing agents and polymers and their evaluation in metal ion separation processes of solvent extraction, synthetic liquid membrane transport, and sorption. Structural variations in acyclic, cyclic, and bicyclic organic ligands were used to probe their influence upon the efficiency and selectivity with which metal ion separations can be performed. A unifying feature of the ligand structures is the presence of one (or more) side arm with a pendent acidic function. When a metal ion is complexed within the central cavity of the ligand, ionization of the side arm(s) produces the requisite anion(s) for formation of an overall electroneutral complex. This markedly enhances extraction/transport efficiency for separations in which movement of aqueous phase anions of chloride, nitrate, or sulfate into an organic medium would be required. Through systematic structural variations, new ligands have been developed for efficient and selective separations of monovalent metal ions (e.g., alkali metal, silver, and thallium cations) and of divalent metal ion species (e.g., alkaline earth metal, lead, and mercury cations). Research results obtained in these fundamental investigations provide important insight for the design and development of ligands suitable for practical metal ion separation applications.

Heavy metal driven co-selection of antibiotic resistance in soil and water bodies impacted by agriculture and aquaculture

Directory of Open Access Journals (Sweden)

Claudia eSeiler

2012-12-01

Full Text Available The use of antibiotic agents as growth promoters was banned in animal husbandry to prevent the selection and spread of antibiotic resistance. However, in addition to antibiotic agents, heavy metals used in animal farming and aquaculture might promote the spread of antibiotic resistance via co-selection. To investigate which heavy metals are likely to co-select for antibiotic resistance in soil and water, the available data on heavy metal pollution, heavy metal toxicity, heavy metal tolerance and co-selection mechanisms was reviewed. Additionally, the risk of metal driven co-selection of antibiotic resistance in the environment was assessed based on heavy metal concentrations that potentially induce this co-selection process. Analyses of the data indicate that agricultural and aquacultural practices represent major sources of soil and water contamination with moderately to highly toxic metals such as copper (Cu and zinc (Zn. If those metals reach the environment and accumulate to selective concentrations they can trigger co-selection of antibiotic resistance. Furthermore, co-selection mechanisms for these heavy metals and clinically as well as veterinary relevant antibiotics have been described. Therefore, studies investigating co-selection in environments impacted by agriculture and aquaculture should focus on Cu and Zn as selecting heavy metals. Furthermore, results of the general selection mechanisms need to be carefully evaluated and the respective environmental background has to be taken into account.

Energy use in selected metal casting facilities - 2003

Energy Technology Data Exchange (ETDEWEB)

Eppich, Robert E. [Eppich Technologies, Syracuse, IN (United States)

2004-05-01

This report represents an energy benchmark for various metal casting processes. It describes process flows and energy use by fuel type and processes for selected casting operations. It also provides recommendations for improving energy efficiency in casting.

Plan for metal barrier selection and testing for NNWSI

International Nuclear Information System (INIS)

Halsey, W.G.; McCright, R.D.

1987-12-01

The Department of Energy's Nevada Nuclear Waste Storage Investigations (NNWSI) Project is evaluating a site at Yucca Mountain in Nevada as a geological repository for the storage of high-level nuclear waste. The Nuclear Waste Management Projects (NWMP) at Lawrence Livermore National Laboratory (LLNL) has the responsibility for design, testing, and performance analysis of the NNWSI waste packages. One portion of this work is the selection and testing of the material for container construction. The anticipated container design is for this material to be a corrosion resistant metal called the metal barrier. This document is the publication version of the Scientific Investigation Plan (SIP) for the Metal Barrier Selection and Testing Task. The SIP serves as a formal planning document for the investigation and is used to assign quality assurance levels to the activities of the task. This document is an informal version for information distribution and has the sections on ''Schedule and Milestones'' and the ''Quality Assurance Level Assignment Sheets'' removed

The effect of selected metals on the central metabolic pathways in ...

African Journals Online (AJOL)

compounds, interfere with xenobiotic metabolic pathways, and may also affect glycolysis, the Krebs cycle, oxidative phosphorylation, protein amino acid metabolism as well as carbohydrate and lipid metabolism. Therefore, in this review, we discuss the two phases of the central metabolic pathways, as well as how metals ...

Sol-Gel Synthesis and Characterization of Selected Transition Metal Nano-Ferrites

Directory of Open Access Journals (Sweden)

Aurelija GATELYTĖ

2011-09-01

Full Text Available In the present work, the sinterability and formation of nanosized yttrium iron garnet (Y3Fe5O12, yttrium perovskite ferrite (YFeO3, cobalt, nickel and zinc iron spinel (CoFe2O4, NiFe2O4 and ZnFe2O4, respectively powders by an aqueous sol-gel processes are investigated. The metal ions, generated by dissolving starting materials of transition metals in the diluted acetic acid were complexed by 1,2-ethanediol to obtain the precursors for the transition metal ferrite ceramics. The phase purity of synthesized nano-compounds was characterized by infrared spectroscopy (IR and powder X-ray diffraction analysis (XRD. The microstructural evolution and morphological features of obtained transition metal ferrites were studied by scanning electron microscopy (SEM.http://dx.doi.org/10.5755/j01.ms.17.3.598

Phytoremediation of soils co-contaminated by organic compounds and heavy metals: bioassays with Lupinus luteus L. and associated endophytic bacteria.

Science.gov (United States)

Gutiérrez-Ginés, M J; Hernández, A J; Pérez-Leblic, M I; Pastor, J; Vangronsveld, J

2014-10-01

In the central part of the Iberian Peninsula there are old sealed landfills containing soils co-contaminated by several heavy metals (Cu, Zn, Pb, Cd, Ni, As, Cr, Fe, Al, Mn) and organic pollutants of different families (hydrocarbons, polycyclic aromatic hydrocarbons, polychlorinated biphenyls, pesticides and other organochlorinated compounds, phenols and volatile compounds), which this work will address. We have focused on phytoremedial plants that are able to deal with this type of complex pollution, not only species that tolerate the joint effect of heavy metals in the soil, but also those that can take advantage of associated bacteria to efficiently break down organic compounds. This study was carried out with Lupinus luteus and its endophytes in two greenhouse experiments: A) growing in a substrate artificially contaminated with benzo(a)pyrene (BaP), and B) using real co-contaminated landfill soils. Endophytes of roots and shoots were isolated in both bioassays. Plant growth-promotion tests and organic pollutant tolerance and degradation tests were conducted on all strains isolated in bioassay A), and on those proving to be pure cultures from bioassay B). The selected landfill is described as are isolation and test procedures. Results indicate that plants did not show toxicity symptoms when exposed to BaP but did when grown in landfill soil. Some endophytes demonstrated plant growth-promotion capacity and tolerance to BaP and other organic compounds (diesel and PCB commercial mixtures). A few strains may even have the capacity to metabolize those organic pollutants. The overall decline in plant growth-promotion capacity in those strains isolated from the landfill soil experiment, compared with those from the bioassay with BaP, may indicate that lupin endophytes are not adapted to metal concentration in roots and shoots and fail to grow. As a result, most isolated root endophytes must have colonized root tissues from the soil. While preliminary degradation tests

Catalysis of metal-clay intercalation compound in the low temperature coal hydrogasification

Energy Technology Data Exchange (ETDEWEB)

Fuda, Kiyoshi; Kimura, Mitsuhiko; Miyamoto, Norimitsu; Matsunaga, Toshiaki

1986-10-23

Focusing the hydrogenating methanation by gaseous phase catalytic reactions of low temperature volatile components, the catalytic effects of Ni metal and the effects of carriers having sensitive effects on the catalytic activities of Ni metal were studied. Sample coals were prepared from Shin-Yubari coal, and Ni hydride-montmorillonite complex catalysts and the catalysts produced by carring Ni nitrate on alumina and burning in hydrogen gas flows were prepared. The hydrogasification were carried out in a reaction tube. As a result, the montmorillonite-Ni compounds catalysts had high catalitic effects and high conversion ratio of 90% or more in the low temperature coal gasification. The catalitic effects of carried Ni metal strongly depended on the carrier substances, and the rank of effects for the carriers was montmorillonite>zeorite>TiO/sub 2/>alpha-Al/sub 2/O/sub 3/>MgO>SiO/sub 2/=gamma-Al/sub 2/O/sub 3/. (3 figs, 3 tabs, 3 refs)

Variant selection of martensites in steel welded joints with low transformation temperature weld metals

International Nuclear Information System (INIS)

Takahashi, Masaru; Yasuda, Hiroyuki Y.

2013-01-01

Highlights: ► We examined the variant selection of martensites in the weld metals. ► We also measured the residual stress developed in the butt and box welded joints. ► 24 martensite variants were randomly selected in the butt welded joint. ► High tensile residual stress in the box welded joint led to the strong variant selection. ► We discussed the rule of the variant selection focusing on the residual stress. -- Abstract: Martensitic transformation behavior in steel welded joints with low transformation temperature weld (LTTW) metal was examined focusing on the variant selection of martensites. The butt and box welded joints were prepared with LTTW metals and 980 MPa grade high strength steels. The residual stress of the welded joints, which was measured by a neutron diffraction technique, was effectively reduced by the expansion of the LTTW metals by the martensitic transformation during cooling after the welding process. In the LTTW metals, the retained austenite and martensite phases have the Kurdjumov–Sachs (K–S) orientation relationship. The variant selection of the martensites in the LTTW metals depended strongly on the type of welded joints. In the butt welded joint, 24 K–S variants were almost randomly selected while a few variants were preferentially chosen in the box welded joint. This suggests that the high residual stress developed in the box welded joint accelerated the formation of specific variants during the cooling process, in contrast to the butt welded joint with low residual stress

COORDINATION COMPOUNDS OF 3D-METALS ACETYLACETONATES WITH THIOSEMICARBAZIDE

Directory of Open Access Journals (Sweden)

T. V. Koksharova

2015-03-01

Full Text Available Coordination Compounds of 3d-Metals acetylacetonates with Thiosemicarbazide were synthesized. Their physical and chemical properties and structure were studied by conductometry, IR spectroscopy, electronic spectroscopy, magnetochemistry and thermo-gravimetricstudies. The complexes compositions correspond to the formulas Co(L2(Acac and M(L(Acac, where M = Cu, Ni, Zn, HL is thiosemicarbazide, HAcac is acetylacetone. All of them are nonelectrolytes. Thiosemicarbazide is deprotonated and coordinated through the nitrogen and sulphur atoms with the formation of four-membered ring in all cases. Acetylacetonate co-ordination mode does not change at acetylacetonates with Thiosemicarbazide interaction. Copper(II and nickel(II complexes have square-planar structure, and cobalt(III complex is octahedral.

Heavy metal driven co-selection of antibiotic resistance in soil and water bodies impacted by agriculture and aquaculture.

Science.gov (United States)

Seiler, Claudia; Berendonk, Thomas U

2012-01-01

The use of antibiotic agents as growth promoters was banned in animal husbandry to prevent the selection and spread of antibiotic resistance. However, in addition to antibiotic agents, heavy metals used in animal farming and aquaculture might promote the spread of antibiotic resistance via co-selection. To investigate which heavy metals are likely to co-select for antibiotic resistance in soil and water, the available data on heavy metal pollution, heavy metal toxicity, heavy metal tolerance, and co-selection mechanisms was reviewed. Additionally, the risk of metal driven co-selection of antibiotic resistance in the environment was assessed based on heavy metal concentrations that potentially induce this co-selection process. Analyses of the data indicate that agricultural and aquacultural practices represent major sources of soil and water contamination with moderately to highly toxic metals such as mercury (Hg), cadmium (Cd), copper (Cu), and zinc (Zn). If those metals reach the environment and accumulate to critical concentrations they can trigger co-selection of antibiotic resistance. Furthermore, co-selection mechanisms for these heavy metals and clinically as well as veterinary relevant antibiotics have been described. Therefore, studies investigating co-selection in environments impacted by agriculture and aquaculture should focus on Hg, Cd, Cu, and Zn as selecting heavy metals. Nevertheless, the respective environmental background has to be taken into account.

Structure, production and properties of high-melting compounds and systems (hard materials and hard metals)

International Nuclear Information System (INIS)

Holleck, H.; Thuemmler, F.

1979-07-01

The report contains contributions by various authors to the research project on the production, structure, and physical properties of high-melting compounds and systems (hard metals and hard materials), in particular WC-, TaC-, and MoC-base materials. (GSCH) [de

Selected topics from recent NMR studies of organolithium compounds

Directory of Open Access Journals (Sweden)

Günther Harald

1999-01-01

Full Text Available After a short introduction to NMR spectroscopy of alkali and alkaline earth metals the review concentrates on NMR investigations of organolithium compounds. The isotopic fingerprint method, which rests on deuterium-induced isotope shifts for 6Li resonances, is introduced and exemplified with applications from the aggregation behavior of cyclopropyllithium systems and mixed aggregate formation between methyllithium and lithium salts. In the following chapter, one- and two-dimensional pulse experiments, both for homo- and for heteronuclear spin systems are discussed. Finally, the structural aspects associated with benzyllithium are outlined and the formation of polylithium systems by lithium reduction of biphenylenes is described.

Diagrams of the variations in the free energy of formation of metallic compounds (1960)

International Nuclear Information System (INIS)

Darras, R.; Loriers, H.

1960-01-01

The variations in the standard free energy ΔG produced during the formation of the principal simple metallic compounds have been calculated as a function of the temperature from recently published data, and are presented in convenient diagram form. Their usefulness in metallurgy is illustrated by some possible applications. (author) [fr

A bis(3-hydroxy-4-pyridinone)-EDTA derivative as a strong chelator for M3+ hard metal ions: complexation ability and selectivity.

Science.gov (United States)

Gama, Sofia; Dron, Paul; Chaves, Silvia; Farkas, Etelka; Santos, M Amélia

2009-08-21

The study of chelating compounds is very important to solve problems related to human metal overload. 3-Hydroxy-3-pyridinones (HP), namely deferiprone, have been clinically used for chelating therapy of Fe and Al over the last decade. A multi-disciplinary search for alternative molecules led us to develop poly-(3-hydroxy-4-pyridinones) to increase metal chelation efficacy. We present herein a complexation study of a new bis-(3-hydroxy-4-pyridinone)-EDTA derivative with a set of M(3+) hard metal ions (M = Fe, Al, Ga), as well as Zn(2+), a biologically relevant metal ion. Thus a systematic aqueous solution equilibrium study was performed using potentiometric and spectroscopic techniques (UV-Vis, NMR methods). These set of results enables the establishment of specific models as well as the determination of thermodynamic stability constants and coordination modes of the metal complexes. The results indicate that this ligand has a higher affinity for chelating to these hard metal ions than deferiprone, and that the coordination occurs mostly through the HP moieties. Furthermore, it was also found that this ligand has a higher selectivity for chelating to M(3+) hard metal ions (M = Fe, Al, Ga) than Zn(2+).

Continuous process for selective metal extraction with an ionic liquid

NARCIS (Netherlands)

Parmentier, D.; Paradis, S.; Metz, S.J.; Wiedmer, S.K.; Kroon, M.C.

2016-01-01

This work describes for the first time a continuous process for selective metal extraction with an ionic liquid (IL) at room temperature. The hydrophobic fatty acid based IL tetraoctylphosphonium oleate ([P8888][oleate]) was specifically chosen for its low viscosity and high selectivity towards

New metals

International Nuclear Information System (INIS)

Bergqvist, U.

1983-12-01

The aim of this report is to estimate the exposure to various metals and metal compounds and discuss the available information of the possible toxic effects of these metals and compounds. In the first section, some metals are defined as those with either a large or a fast increasing exposure to living organisms. The available information on toxicity is discussed in the second section. In the third section interesting metals are defined as compounds having a large exposure and an apparent insufficient knowledge of their possible toxic effects. Comments on each of these metals are also to be found in the third section. (G.B.)

An alternative picture of alkali-metal-mediated metallation: cleave and capture chemistry.

Science.gov (United States)

Mulvey, Robert E

2013-05-21

This perspective article takes an alternative look at alkali-metal-mediated chemistry (exchange of a relatively inert C-H bond for a more reactive C-metal bond by a multicomponent reagent usually containing an alkali metal and a less electropositive metal such as magnesium or zinc). It pictures that the cleavage of selected C-H bonds can be accompanied by the capturing of the generated anion by the multi (Lewis acid)-(Lewis base) character of the residue of the bimetallic base. In this way small atoms or molecules (hydrides, oxygen-based anions) as well as sensitive organic anions (of substituted aromatic compounds, ethers or alkenes) can be captured. Cleave and capture reactions which occur in special positions on the organic substrate are also included.

Half-metallic ferromagnetism in full-Heusler compounds ACaX2 (A = K and Rb; X = N and O)

International Nuclear Information System (INIS)

Umamaheswari, R.; Vijayalakshmi, D.; Yogeswari, M.; Kalpana, G.

2014-01-01

Electronic structure and magnetic properties of hypothetical ACaX 2 (A = K and Rb; X= N and O) compounds in full-Heusler phase have been investigated based on density functional theory (DFT) within the local density approximation (LDA). The electronic band structures and density of states of these compounds show that the spin-down electrons have metallic, and the spin-up electrons have a semi conducting gap resulting in stable half-metallic ferromagnetic behaviour. The strong spin polarization of 2p states of N and O atoms is found to be the origin of ferromagnetism which results in a total magnetic moment of 3 μB and 1 μB respectively

Molecular modeling of inorganic compounds

National Research Council Canada - National Science Library

Comba, Peter; Hambley, Trevor W; Martin, Bodo

2009-01-01

... mechanics to inorganic and coordination compounds. Initially, simple metal complexes were modeled, but recently the field has been extended to include organometallic compounds, catalysis and the interaction of metal ions with biological macromolecules. The application of molecular mechanics to coordination compounds is complicated by the numbe...

Investigation of spin-gapless semiconductivity and half-metallicity in Ti2MnAl-based compounds

International Nuclear Information System (INIS)

Lukashev, P.; Staten, B.; Hurley, N.; Kharel, P.; Gilbert, S.; Fuglsby, R.; Huh, Y.; Valloppilly, S.; Zhang, W.; Skomski, R.; Sellmyer, D. J.; Yang, K.

2016-01-01

The increasing interest in spin-based electronics has led to a vigorous search for new materials that can provide a high degree of spin polarization in electron transport. An ideal candidate would act as an insulator for one spin channel and a conductor or semiconductor for the opposite spin channel, corresponding to the respective cases of half-metallicity and spin-gapless semiconductivity. Our first-principle electronic-structure calculations indicate that the metallic Heusler compound Ti 2 MnAl becomes half-metallic and spin-gapless semiconducting if half of the Al atoms are replaced by Sn and In, respectively. These electronic structures are associated with structural transitions from the regular cubic Heusler structure to the inverted cubic Heusler structure.

Electronic structure, Fermi surface and optical properties of metallic compound Be8(B48)B2

International Nuclear Information System (INIS)

Reshak, A.H.; Azam, Sikander; Alahmed, Z.A.; Chyský, Jan

2014-01-01

The band structure, density of states, electronic charge density, Fermi surface and optical properties for B 8 (Be 48 )B 2 compound has been investigated in the support of density functional theory (DFT). The atomic positions of B 8 (Be 48 )B 2 compound were optimized by minimization of the forces acting on the atoms using the full potential linear augmented plane wave (FPLAPW) method. We have employed the local density approximation (LDA), generalized gradient approximation (GGA) and Engal-Vosko GGA (EVGGA) to indulgence the exchange correlation potential by solving Kohn–Sham equations. The result shows that the compound is metallic with sturdy hybridization near the Fermi energy level (E F ). The density of states at Fermi energy, N(E F ), is determined by the overlaping between B-p, B-s and Be-s states. This overlaping is strong enough indicating metallic origin with different values of N(E F ). These values are 16.4, 16.27 and 14.89 states/eV, and the corresponding bare linear low-temperature electronic specific heat coefficient (γ) is found to be 2.84, 2.82 and 2.58 mJ/mol K 2 for EVGGA, GGA and LDA respectively. There exists a strong hybridization between B-s and B-p states, also between B-s and Be-p states around the Fermi level. The Fermi surface is composed of three sheets. These sheets consist of set of holes and electrons. The bonding features of the compounds are analyzed using the electronic charge density in the (101 and −101) crystallographic planes and also the analyzing of charge density shows covalent bonding between B and B. The linear optical properties are also deliberated and discussed in particulars. - Highlights: • The compound is metallic. • The density of states at the Fermi energy is calculated. • The bare linear low-temperature electronic specific heat coefficient is obtained. • Fermi surface is composed of three sheets. • The bonding features are analyzed using the electronic charge density

Application of Metal Catalysts for High Selectivity of Glycerol Conversion to Alcohols

Science.gov (United States)

2010-11-01

The objective of this project is to determine the applicability of metal-based catalysts and optimize the process conditions for thermochemically producing primary alcohols. Metal catalysts were evaluated for their selectivities for producing alcohol...

Chemical and biological properties of toxic metals and use of chelating agents for the pharmacological treatment of metal poisoning

Energy Technology Data Exchange (ETDEWEB)

Sinicropi, Maria Stefania; Caruso, Anna [University of Calabria, Department of Pharmaceutical Sciences, Rende (Italy); Amantea, Diana [University of Calabria, Department of Pharmacobiology, Rende (Italy); Saturnino, Carmela [University of Salerno, Department of Pharmaceutical Sciences, Fisciano (Italy)

2010-07-15

Exposure to toxic metals is a well-known problem in industrialized countries. Metals interfere with a number of physiological processes, including central nervous system (CNS), haematopoietic, hepatic and renal functions. In the evaluation of the toxicity of a particular metal it is crucial to consider many parameters: chemical forms (elemental, organic or inorganic), binding capability, presence of specific proteins that selectively bind metals, etc. Medical treatment of acute and chronic metal toxicity is provided by chelating agents, namely organic compounds capable of interacting with metal ions to form structures called chelates. The present review attempts to provide updated information about the mechanisms, the cellular targets and the effects of toxic metals. (orig.)

Investigations on organolead compounds V. Lead---lead bond cleavage reactions of hexaphenyldilead

NARCIS (Netherlands)

Willemsens, L.C.; Kerk, G.J.M. van der

1968-01-01

It has been shown that a number of nucleophilic and weakly electrophilic reagents (organolithium and organomagnesium compounds, metallic lithium, potassium permanganate, sodium ethoxide, diaryl disulphides, sulphur, ozone, hypochlorous acid and iodine/iodide) selectively cleave the lead---lead bond

Determination of Volatile Organic Compounds in Selected Strains of Cyanobacteria

Directory of Open Access Journals (Sweden)

Ivan Milovanović

2015-01-01

Full Text Available Microalgal biomass can be used in creating various functional food and feed products, but certain species of microalgae and cyanobacteria are known to produce various compounds causing off-flavour. In this work, we investigated selected cyanobacterial strains of Spirulina, Anabaena, and Nostoc genera originating from Serbia, with the aim of determining the chemical profile of volatile organic compounds produced by these organisms. Additionally, the influence of nitrogen level during growth on the production of volatile compounds was investigated for Nostoc and Anabaena strains. In addition, multivariate techniques, namely, principal component analysis (PCA and hierarchical cluster analysis (HCA, were used for making distinction among different microalgal strains. The results show that the main volatile compounds in these species are medium chain length alkanes, but other odorous compounds such as 2-methylisoborneol (0.51–4.48%, 2-pentylfuran (0.72–8.98%, β-cyclocitral (0.00–1.17%, and β-ionone (1.15–2.72% were also detected in the samples. Addition of nitrogen to growth medium was shown to negatively affect the production of 2-methylisoborneol, while geosmin was not detected in any of the analyzed samples, which indicates that the manipulation of growth conditions may be useful in reducing levels of some unwanted odor-causing components.

Thermochemistry of some binary lead and transition metal compounds by high temperature direct synthesis calorimetry

Energy Technology Data Exchange (ETDEWEB)

Meschel, S.V., E-mail: meschel@jfi.uchicago.edu [Illinois Institute of Technology,Thermal Processing Technology Center, 10 W. 32nd Street, Chicago, Illinois 60615 (United States); Gordon Center for Integrated Science, 929 E. 57th Street, Chicago, Illinois 60637 (United States); Nash, P. [Illinois Institute of Technology,Thermal Processing Technology Center, 10 W. 32nd Street, Chicago, Illinois 60615 (United States); Chen, X.Q.; Wei, P. [Materials processing Modeling Division, Shenyang National Laboratory for Materials Science, Institute of Metals Research, 72 Wenhua Road, Shenyang City (China)

2015-06-05

Highlights: • Studied binary lead-transition metal alloys by high temperature calorimetry. • Determined the enthalpies of formation of 8 alloys. • Compared the measurements with predictions by the model of Miedema and by the ab initio method. - Abstract: The standard enthalpies of formation of some binary lead and transition metal compounds have been measured by high temperature direct synthesis calorimetry. The reported results are: Pb{sub 3}Sc{sub 5}(−61.3 ± 2.9); PbTi{sub 4}(−16.6 ± 2.4); Pb{sub 3}Y{sub 5}(−64.8 ± 3.6); Pb{sub 3}Zr{sub 5}(−50.6 ± 3.1); PbNb{sub 3}(−10.4 ± 3.4); PbRh(−16.5 ± 3.3); PbPd{sub 3}(−29.6 ± 3.1); PbPt(−34.7 ± 3.3) kJ/mole of atoms. We will compare our results with previously published measurements. We will also compare the experimental measurements with enthalpies of formation of transition metal compounds with elements in the same vertical column in the periodic table. We will compare our measurements with predicted values on the basis of the semi empirical model of Miedema and coworkers and with ab initio values when available.

Magnetism in rare-earth metals and rare-earth intermetallic compounds

International Nuclear Information System (INIS)

Johansson, B.; Nordstroem, L.; Eriksson, O.; Brooks, M.S.S.

1991-01-01

Some of out recent local spin density electronic structure calculations for a number of ferromagnetic rare-earth systems are reviewed. A simplified model of the level densities for rare-earth (R) transition metal (M) intermetallic compounds, R m M n , is used to describe in a simple way the main features of their basic electronic structure. Explicit calculations for LuFe 2 and RFe 2 (R=Gd-Yb) systems are presented, where a method to treat simultaneously the localized 4f and the conduction electron spin magnetism is introduced. Thereby it becomes possible to calculate the K RM exchange coupling constant. This method is also used to study theoretically the permanent magnet material Nd 2 Fe 14 B. The electronic structure of the anomalous ferromagnets CeFe 2 and CeCo 5 is discussed and an induced 4f itinerant magnetism is predicted. The γ-α transition in cerium metal is considered, and results from calculations including orbital polarization are presented, where a volume collapse of 10% is obtained. On one side of the transition the 4f electrons are calculated to be essentially non-bonding (localized) and on the other side they are found to contribute to the metallic bonding and this difference in behaviour gives rise to the volume collapse. Recent calculations by Wills, Eriksson and Boring for the crystal structure changes in cerium metal under high pressure are discussed. Their successful results imply an itinerant picture for the 4f electrons in α-cerium. Consequently this strongly supports the view that the γ-α phase transformation is caused by a Mott transition of the 4f electrons. (orig.)

Selective and low temperature transition metal intercalation in layered tellurides

Science.gov (United States)

Yajima, Takeshi; Koshiko, Masaki; Zhang, Yaoqing; Oguchi, Tamio; Yu, Wen; Kato, Daichi; Kobayashi, Yoji; Orikasa, Yuki; Yamamoto, Takafumi; Uchimoto, Yoshiharu; Green, Mark A.; Kageyama, Hiroshi

2016-01-01

Layered materials embrace rich intercalation reactions to accommodate high concentrations of foreign species within their structures, and find many applications spanning from energy storage, ion exchange to secondary batteries. Light alkali metals are generally most easily intercalated due to their light mass, high charge/volume ratio and in many cases strong reducing properties. An evolving area of materials chemistry, however, is to capture metals selectively, which is of technological and environmental significance but rather unexplored. Here we show that the layered telluride T2PTe2 (T=Ti, Zr) displays exclusive insertion of transition metals (for example, Cd, Zn) as opposed to alkali cations, with tetrahedral coordination preference to tellurium. Interestingly, the intercalation reactions proceed in solid state and at surprisingly low temperatures (for example, 80 °C for cadmium in Ti2PTe2). The current method of controlling selectivity provides opportunities in the search for new materials for various applications that used to be possible only in a liquid. PMID:27966540

Synthesis and Characterization of Quaternary Metal Chalcogenide Aerogels for Gas Separation and Volatile Hydrocarbon Adsorption

KAUST Repository

Edhaim, Fatimah A.

2017-01-01

as sorbents for selective gas separation and volatile organic compounds adsorption. They showed preferential adsorption of polarizable gases (CO2) and organic compounds (toluene). Ion exchange and heavy metal remediation properties have also been demonstrated

The influence of coordination geometry and valency on the K-edge absorption near edge spectra of selected chromium compounds

International Nuclear Information System (INIS)

Pantelouris, A.; Modrow, H.; Pantelouris, M.; Hormes, J.; Reinen, D.

2004-01-01

X-ray absorption spectra at the chromium K-edge are reported for a number of selected chromium compounds of known chemical structure. The spectra were obtained with use of synchrotron radiation available at the ELectron Stretcher Accelerator ELSA in Bonn. The compounds studied include the tetrahedrally coordinated compounds Ca 2 Ge 0.8 Cr 0.2 O 4 , Ba 2 Ge 0.1 Cr 0.9 O 4 , Sr 2 CrO 4 , Ca 2 (PO 4 ) x (CrO 4 ) 1-x Cl (x=0.25,0.5), Ca 5 (CrO 4 ) 3 Cl, CrO 3 , the octahedrally coordinated compounds Cr(II)-acetate, CrCl 3 , CrF 3 , Cr 2 O 3 , KCr(SO 4 ) 2 · 12H 2 O, CrO 2 and cubic coordinated metallic chromium. In these compounds chromium exhibits a wide range of formal oxidation states (0 to VI). The absorption features in the near edge region are shown to be characteristic of the spatial environment of the absorbing atom. The occurrence of a single pre-edge line easily allows one to distinguish between tetrahedral and octahedral coordination geometry, whereas the energy position of the absorption edge is found to be very sensitive to the valency of the excited chromium atom. Calculations of the ionisation potential of Cr in different oxidation states using the non-relativistic Hartree-Fock method (Froese-Fischer) confirm that the ionisation limit shifts to higher energy with increasing Cr valency. More detailed information on the electronic structure of the different compounds is gained by real-space full multiple scattering calculations using the FEFF8 code

The influence of coordination geometry and valency on the K-edge absorption near edge spectra of selected chromium compounds

Science.gov (United States)

Pantelouris, A.; Modrow, H.; Pantelouris, M.; Hormes, J.; Reinen, D.

2004-05-01

X-ray absorption spectra at the chromium K-edge are reported for a number of selected chromium compounds of known chemical structure. The spectra were obtained with use of synchrotron radiation available at the ELectron Stretcher Accelerator ELSA in Bonn. The compounds studied include the tetrahedrally coordinated compounds Ca 2Ge 0.8Cr 0.2O 4, Ba 2Ge 0.1Cr 0.9O 4, Sr 2CrO 4, Ca 2(PO 4) x(CrO 4) 1- xCl ( x=0.25,0.5), Ca 5(CrO 4) 3Cl, CrO 3, the octahedrally coordinated compounds Cr(II)-acetate, CrCl 3, CrF 3, Cr 2O 3, KCr(SO 4) 2 · 12H 2O, CrO 2 and cubic coordinated metallic chromium. In these compounds chromium exhibits a wide range of formal oxidation states (0 to VI). The absorption features in the near edge region are shown to be characteristic of the spatial environment of the absorbing atom. The occurrence of a single pre-edge line easily allows one to distinguish between tetrahedral and octahedral coordination geometry, whereas the energy position of the absorption edge is found to be very sensitive to the valency of the excited chromium atom. Calculations of the ionisation potential of Cr in different oxidation states using the non-relativistic Hartree-Fock method (Froese-Fischer) confirm that the ionisation limit shifts to higher energy with increasing Cr valency. More detailed information on the electronic structure of the different compounds is gained by real-space full multiple scattering calculations using the FEFF8 code.

Synthesis of Alkanethiolate-Capped Metal Nanoparticles Using Alkyl Thiosulfate Ligand Precursors: A Method to Generate Promising Reagents for Selective Catalysis

Directory of Open Access Journals (Sweden)

Khin Aye San

2018-05-01

Full Text Available Evaluation of metal nanoparticle catalysts functionalized with well-defined thiolate ligands can be potentially important because such systems can provide a spatial control in the reactivity and selectivity of catalysts. A synthetic method utilizing Bunte salts (sodium S-alkylthiosulfates allows the formation of metal nanoparticles (Au, Ag, Pd, Pt, and Ir capped with alkanethiolate ligands. The catalysis studies on Pd nanoparticles show a strong correlation between the surface ligand structure/composition and the catalytic activity and selectivity for the hydrogenation/isomerization of alkenes, dienes, trienes, and allylic alcohols. The high selectivity of Pd nanoparticles is driven by the controlled electronic properties of the Pd surface limiting the formation of Pd–alkene adducts (or intermediates necessary for (additional hydrogenation. The synthesis of water soluble Pd nanoparticles using ω-carboxylate-S-alkanethiosulfate salts is successfully achieved and these Pd nanoparticles are examined for the hydrogenation of various unsaturated compounds in both homogeneous and heterogeneous environments. Alkanethiolate-capped Pt nanoparticles are also successfully synthesized and further investigated for the hydrogenation of various alkynes to understand their geometric and electronic surface properties. The high catalytic activity of activated terminal alkynes, but the significantly low activity of internal alkynes and unactivated terminal alkynes, are observed for Pt nanoparticles.

Calculations of hyperfine interactions in transition metal compounds in the local density approximation

International Nuclear Information System (INIS)

Guenzburger, D.J.R.

1982-01-01

A survey is made of some theoretical calculations of electrostatic and magnetic hyperfine interactions in transition metal compounds and complex irons. The molecular orbital methods considered are the Multiple Scattering and Discrete Variational, in which the local Xα approximation for the exchange interaction is employed. Emphasis is given to the qualitative informations, derived from the calculations, relating the hyperfine parameters to characteristics of the chemical bonds. (Author) [pt

gem-Difluoroolefination of Diazo Compounds with TMSCF3 or TMSCF2Br: Transition-Metal-Free Cross-Coupling of Two Carbene Precursors.

Science.gov (United States)

Hu, Mingyou; Ni, Chuanfa; Li, Lingchun; Han, Yongxin; Hu, Jinbo

2015-11-18

A new olefination protocol for transition-metal-free cross-coupling of two carbene fragments arising from two different sources, namely, a nonfluorinated carbene fragment resulting from a diazo compound and a difluorocarbene fragment derived from Ruppert-Prakash reagent (TMSCF3) or TMSCF2Br, has been developed. This gem-difluoroolefination proceeds through the direct nucleophilic addition of diazo compounds to difluorocarbene followed by elimination of N2. Compared to previously reported Cu-catalyzed gem-difluoroolefination of diazo compounds with TMSCF3, which possesses a narrow substrate scope due to a demanding requirement on the reactivity of diazo compounds and in-situ-generated CuCF3, this transition-metal-free protocol affords a general and efficient approach to various disubstituted 1,1-difluoroalkenes, including difluoroacrylates, diaryldifluoroolefins, as well as arylalkyldifluoroolefins. In view of the ready availability of diazo compounds and difluorocarbene reagents and versatile transformations of 1,1-difluoroalkenes, this new gem-difluoroolefination method is expected to find wide applications in organic synthesis.

Heavy metal vaporization and abatement during thermal treatment of modified wastes

International Nuclear Information System (INIS)

Rio, S.; Verwilghen, C.; Ramaroson, J.; Nzihou, A.; Sharrock, P.

2007-01-01

This study examines the vaporization percentage and partitioning of heavy metals Cd, Pb and Zn during thermal treatment of wastes with added PVC, heavy metals or phosphate, and the efficiency of sorbents for removal of these metallic compounds in flue gas of an industrial solid waste incinerator. Firstly, vaporization experiments were carried out to determine the behavior of heavy metals during combustion under various conditions (type of waste, temperature, presence of chloride or phosphate ...). The experimental results show relatively high vaporization percentage of metallic compounds within fly ash and limestone matrix while heavy metals within sediments treated with phosphoric acid are less volatile. Vaporization of metals increases with increasing temperature and with chloride addition. The thermal behavior of the selected heavy metals and their removal by sorbents (sodium bicarbonate, activated carbon) was also studied in an industrial solid waste incinerator. These pilot scale experiments confirm that heavy metals are concentrated in fly ashes and cyclone residues, thus effectively controlling their release to the atmosphere

Screening and identification of phytotoxic volatile compounds in medicinal plants and characterizations of a selected compound, eucarvone.

Science.gov (United States)

Sunohara, Yukari; Baba, Yohei; Matsuyama, Shigeru; Fujimura, Kaori; Matsumoto, Hiroshi

2015-07-01

Screening and identification of phytotoxic volatile compounds were performed using 71 medicinal plant species to find new natural compounds, and the characterization of the promising compound was investigated to understand the mode of action. The volatile compounds from Asarum sieboldii Miq. showed the strongest inhibitory effect on the hypocotyl growth of lettuce seedlings (Lactuca sativa L.cv. Great Lakes 366), followed by those from Schizonepeta tenuifolia Briquet and Zanthoxylum piperitum (L.) DC.. Gas chromatography-mass spectrometry (GC/MS) identified four volatile compounds, α-pinene (2,6,6-trimethylbicyclo[3.1.1]hept-2-ene), β-pinene (6,6-dimethyl-2-methylenebicyclo[3.1.1]heptane), 3-carene (3,7,7-trimethylbicyclo[4.1.0]hept-3-ene), and eucarvone (2,6,6-trimethy-2,4-cycloheptadien-1-one), from A. sieboldii, and three volatile compounds, limonene (1-methyl-4-(1-methylethenyl)-cyclohexene), menthone (5-methyl-2-(propan-2-yl)cyclohexan-1-one), and pulegone (5-methyl-2-propan-2-ylidenecyclohexan-1-one), from S. tenuifolia. Among these volatile compounds, eucarvone, menthone, and pulegone exhibited strong inhibitory effects on both the root and shoot growth of lettuce seedlings. Eucarvone-induced growth inhibition was species-selective. Cell death, the generation of reactive oxygen species (ROS), and lipid peroxidation were induced in susceptible finger millet seedlings by eucarvone treatment, whereas this compound (≤158 μM) did not cause the increase of lipid peroxidation and ROS production in tolerant maize. The results of the present study show that eucarvone can have strong phytotoxic activity, which may be due to ROS overproduction and subsequent oxidative damage in finger millet seedlings.

Power characteristics of the metal compounds formation process during the friction stir welding

Directory of Open Access Journals (Sweden)

Rzaev Radmir

2017-01-01

Full Text Available An influence of the power characteristics on the formation process of the uniform metals compound during the welding with friction stirringis being examined in this article.A dependency between the machine-tool engine power input and the instrument tilt during the FSW for the aluminum alloy AD31, copper alloy M1, titanium alloy OT4-1 and steel St-3 low-alloyed has been explored. A question of the stabilization of power consumption process while the establishment of superplastic condition of welded metal during the FSW has also been reviewed. A dependency revealed between the power characteristics, the geometry of the formation, the rotation speeds, the longitudinal displacement of the tool and its dimensions for fixed values of the parameters during the FSW.

A Comparative Discussion of the Catalytic Activity and CO2-Selectivity of Cu-Zr and Pd-Zr (Intermetallic Compounds in Methanol Steam Reforming

Directory of Open Access Journals (Sweden)

Norbert Köpfle

2017-02-01

Full Text Available The activation and catalytic performance of two representative Zr-containing intermetallic systems, namely Cu-Zr and Pd-Zr, have been comparatively studied operando using methanol steam reforming (MSR as test reaction. Using an inverse surface science and bulk model catalyst approach, we monitored the transition of the initial metal/intermetallic compound structures into the eventual active and CO2-selective states upon contact to the methanol steam reforming mixture. For Cu-Zr, selected nominal stoichiometries ranging from Cu:Zr = 9:2 over 2:1 to 1:2 have been prepared by mixing the respective amounts of metallic Cu and Zr to yield different Cu-Zr bulk phases as initial catalyst structures. In addition, the methanol steam reforming performance of two Pd-Zr systems, that is, a bulk system with a nominal Pd:Zr = 2:1 stoichiometry and an inverse model system consisting of CVD-grown ZrOxHy layers on a polycrystalline Pd foil, has been comparatively assessed. While the CO2-selectivity and the overall catalytic performance of the Cu-Zr system is promising due to operando formation of a catalytically beneficial Cu-ZrO2 interface, the case for Pd-Zr is different. For both Pd-Zr systems, the low-temperature coking tendency, the high water-activation temperature and the CO2-selectivity spoiling inverse WGS reaction limit the use of the Pd-Zr systems for selective MSR applications, although alloying of Pd with Zr opens water activation channels to increase the CO2 selectivity.

Perspectives from ab-initio and tight-binding: Applications to transition metal compounds and superlattices

Science.gov (United States)

Venkataraman, Vijay Shankar

The experimental and theoretical study of transition metal compounds have occupied condensed matter physicists for the best part of the last century. The rich variety of physical behaviour exhibited by these compounds owes its origin to the subtle balance of the energy scales at play for the d orbitals. In this thesis, we study three different systems comprised of transition metal atoms from the third, the fourth, and the fifth group of the periodic table using a combination of ab-initio density functional theory (DFT) computations and effective tight-binding models for the electronic properties. We first consider the electronic properties of artificially fabricated perovskite superlattices of the form [(SrIrO3)m / SrTiO3] with integer m denoting the number of layers of SrIrO3. After discussing the results of experiments undertaken by our collaborators, we present the results of our DFT calculations and build tight-binding models for the m = 1 and m = 2 superlattices. The active ingredient is found to be the 5d orbitals with significant spin-orbit coupling. We then study the energies of magnetic ground states within DFT and compare and contrast our results with those obtained for the bulk Ruddlesden-Popper iridates. Together with experimental measurements, our results suggest that these superlattices are an exciting venue to probe the magnetism and metal-insulator transitions that occur from the intricate balance of the spin-orbit coupling and electron interactions, as has been reported for their bulk counterparts. Next, we consider alpha-RuCl3, a honeycomb lattice compound. We first show using DFT calculations in conjunction with experiments performed by our collaborators, how spin-orbit coupling in the 4d orbitals of Ru is essential to understand the insulating state realized in this compound. Then, in the latter half of the chapter, we study the magnetic ground states of a two-dimensional analogue of alpha-RuCl3 in weak and strong-coupling regimes obtained from

Determination of uranium metal concentration in irradiated fuel storage basin sludge using selective dissolution

International Nuclear Information System (INIS)

Delegard, C.H.; Sinkov, S.I.; Chenault, J.W.; Schmidt, A.J.; Pool, K.N.; Welsh, T.L.

2014-01-01

Irradiated uranium metal fuel was stored underwater in the K East and K West storage basins at the US Department of Energy Hanford Site. The uranium metal under damaged cladding reacted with water to generate hydrogen gas, uranium oxides, and spalled uranium metal particles which intermingled with other particulates to form sludge. While the fuel has been removed, uranium metal in the sludge remains hazardous. An expeditious routine method to analyze 0.03 wt% uranium metal in the presence of >30 wt% total uranium was needed to support safe sludge management and processing. A selective dissolution method was designed based on the rapid uranium oxide dissolution but very low uranium metal corrosion rates in hot concentrated phosphoric acid. The uranium metal-bearing heel from the phosphoric acid step then is rinsed before the uranium metal is dissolved in hot concentrated nitric acid for analysis. Technical underpinnings of the selective dissolution method, including the influence of sludge components, were investigated to design the steps and define the reagents, quantities, concentrations, temperatures, and times within the selective dissolution analysis. Tests with simulant sludge proved the technique feasible. Tests with genuine sludge showed a 0.0028 ± 0.0037 wt% (at one standard deviation) uranium metal analytical background, a 0.011 wt% detection limit, and a 0.030 wt% quantitation limit in settled (wet) sludge. In tests using genuine K Basin sludge spiked with uranium metal at concentrations above the 0.030 wt% ± 25 % (relative) quantitation limit, uranium metal recoveries averaged 99.5 % with a relative standard deviation of 3.5 %. (author)

Micro- and Nanostructured Metal Oxide Chemical Sensors for Volatile Organic Compounds

Science.gov (United States)

Alim, M. A.; Penn, B. G.; Currie, J. R., Jr.; Batra, A. K.; Aggarwal, M. D.

2008-01-01

Aeronautic and space applications warrant the development of chemical sensors which operate in a variety of environments. This technical memorandum incorporates various kinds of chemical sensors and ways to improve their performance. The results of exploratory investigation of the binary composite polycrystalline thick-films such as SnO2-WO3, SnO2-In2O3, SnO2-ZnO for the detection of volatile organic compound (isopropanol) are reported. A short review of the present status of the new types of nanostructured sensors such as nanobelts, nanorods, nanotube, etc. based on metal oxides is presented.

Behaviour of mercury compounds in soil

Energy Technology Data Exchange (ETDEWEB)

Booer, J R

1944-01-01

The uses of inorganic compounds of mercury for the control of plant pests is reviewed, and a summary of the relevant chemical and physical properties of the compounds concerned is given. On chemical evidence a working hypothesis is propounded showing that all compounds may be expected to decompose into metallic mercury. A pot technique is described by means of which a correlation can be obtained between the effective mercury content of a given soil sample and the rate of growth of wheat seedlings. The mathematical treatment of the results is described, and the validity of the pot technique is verified by statistical analysis of results. Using the pot technqiue it is shown that volatilization losses are insignificant but that mercury is slowly rendered ineffective by the formation of mercuric sulphide. The effect of sulphur-reducing bacteria is considered and the influence of Vibrio desulphuricans on mercury is studied in detail. Experimental evidence obtained by the pot technique is produced to show that mercurous chloride slowly decomposes in the soil giving mercury and mercuric chloride, mercuric chloride rapidly decomposes into mercury and mercurous chloride, and other inorganic compounds decompose directly into mercury. The working hypothesis is substantiated in all major aspects. The uses and properties of the organo-mercury compounds are then discussed. Type compounds selected are ethyl mercury phosphate, phenyl mercury acetate and methoxyethyl mercury acetate. Using the pot technique it is shown that the formation of organo-mercury clays takes place and that these clays decompose giving metallic mercury. A mechanism is suggested.

Separation properties of the MIL-125(Ti) Metal-Organic Framework in high-performance liquid chromatography revealing cis/trans selectivity.

Science.gov (United States)

Van der Perre, Stijn; Liekens, Anuschka; Bueken, Bart; De Vos, Dirk E; Baron, Gino V; Denayer, Joeri F M

2016-10-21

Monodisperse MIL-125(Ti) Metal-Organic Framework crystals were synthesized and studied as stationary phase in high performance liquid chromatography (HPLC). Different pure compounds and model mixtures (including stereoisomer mixtures) were injected from which chromatographic parameters, including selectivities and resolution factors, were determined to evaluate the adsorption properties and separation performance of MIL-125(Ti) in liquid phase. The MIL-125(Ti) framework displayed a trans selectivity for cis/trans difunctionalized cyclohexane molecules with high selectivity and resolution for 1,3-dimethylcyclohexane and 4-ethylcyclohexanol. The slurry-packed column was further characterized via van Deemter analysis. Fitting of the van Deemter equation through the experimental points allowed to define the contributions of the different processes to plate height with a significant proportion of the A-term, reflecting the importance of a good crystal packing. Although high in comparison to commercial HPLC stationary phases, a very good plate height of around 50μm was found. Copyright © 2016 Elsevier B.V. All rights reserved.

Electrolyte solutions including a phosphoranimine compound, and energy storage devices including same

Science.gov (United States)

Klaehn, John R.; Dufek, Eric J.; Rollins, Harry W.; Harrup, Mason K.; Gering, Kevin L.

2017-09-12

An electrolyte solution comprising at least one phosphoranimine compound and a metal salt. The at least one phosphoranimine compound comprises a compound of the chemical structure ##STR00001## where X is an organosilyl group or a tert-butyl group and each of R.sup.1, R.sup.2, and R.sup.3 is independently selected from the group consisting of an alkyl group, an aryl group, an alkoxy group, or an aryloxy group. An energy storage device including the electrolyte solution is also disclosed.

Study of impurity composition of some compounds of refractory metals by instrumental neutron activation analysis

International Nuclear Information System (INIS)

Kaganov, L.K.; Dzhumakulov, D.T.; Mukhamedshina, N.M.

1994-01-01

The compounds of refractory transition metals find wide application in all fields of engineering, in particular in microelectronics to manufacture contact-barrier layers of thin-film current-conducting systems of silicon instruments, large and very large scale integrated circuits. Production of such materials is realted with the need to apply the analytical control methods that allow to determine a large number of elements with high reliability. The instrumental neutron-activation techniques have been developed to determine impurity composition of the following compounds: MoSi 2 , WSi 2 , TiB 2 , NbB 2 , TiC, NbC

Selective recovery of gold and other metal ions from an algal biomass

Energy Technology Data Exchange (ETDEWEB)

Darnall, D.W.; Greene, B.; Henzl, M.T.; Hosea, J.M.; McPherson, R.A.; Sneddon, J.; Alexander, M.D.

1986-02-01

The authors observed that the pH dependence of the binding of Au/sup 3 +/, Ag/sup +/, and Hg/sup 2 +/ to the algae Chlorella vulgaris is different than the binding of other metal ions. Between pH 5 and 7, a variety of metal ions bind strongly to the cell surface. Most of these algal-bound metal ions can be selectively desorbed by lowering the pH to 2; however, Au/sup 3 +/, Hg/sup 2 +/, and Ag/sup +/ are all bound strongly at pH 2. Addition of a strong ligand at different pHs is required to elute these ions from the algal surface. Algal-bound gold and mercury can be selectively eluted by using mercaptoethanol. An elution scheme is demonstrated for the binding and selective recovery of Cu/sup 2 +/, Zn/sup 2 +/, Au/sup 3 +/, and Hg/sup 2 +/ from an equimolar mixture. 20 references, 2 figures.

Heavy metal driven co-selection of antibiotic resistance in soil and water bodies impacted by agriculture and aquaculture

OpenAIRE

Seiler, Claudia; Berendonk, Thomas U.

2012-01-01

The use of antibiotic agents as growth promoters was banned in animal husbandry to prevent the selection and spread of antibiotic resistance. However, in addition to antibiotic agents, heavy metals used in animal farming and aquaculture might promote the spread of antibiotic resistance via co-selection. To investigate which heavy metals are likely to co-select for antibiotic resistance in soil and water, the available data on heavy metal pollution, heavy metal toxicity, heavy metal tolerance ...

Selective versus routine patch metal allergy testing to select bar material for the Nuss procedure in 932 patients over 10years.

Science.gov (United States)

Obermeyer, Robert J; Gaffar, Sheema; Kelly, Robert E; Kuhn, M Ann; Frantz, Frazier W; McGuire, Margaret M; Paulson, James F; Kelly, Cynthia S

2018-02-01

The aim of the study was to determine the role of patch metal allergy testing to select bar material for the Nuss procedure. An IRB-approved (11-04-WC-0098) single institution retrospective, cohort study comparing selective versus routine patch metal allergy testing to select stainless steel or titanium bars for Nuss repair was performed. In Cohort A (9/2004-1/2011), selective patch testing was performed based on clinical risk factors. In Cohort B (2/2011-9/2014), all patients were patch tested. The cohorts were compared for incidence of bar allergy and resultant premature bar loss. Risk factors for stainless steel allergy or positive patch test were evaluated. Cohort A had 628 patients with 63 (10.0%) selected for patch testing, while all 304 patients in Cohort B were tested. Over 10years, 15 (1.8%) of the 842 stainless steel Nuss repairs resulted in a bar allergy, and 5 had a negative preoperative patch test. The incidence of stainless steel bar allergy (1.8% vs 1.7%, p=0.57) and resultant bar loss (0.5% vs 1.3%, p=0.23) was not statistically different between cohorts. An allergic reaction to a stainless steel bar or a positive patch test was more common in females (OR=2.3, pbar allergies occur at a low incidence with either routine or selective patch metal allergy testing. If selective testing is performed, it is advisable in females and patients with a personal or family history of metal sensitivity. A negative preoperative patch metal allergy test does not preclude the possibility of a postoperative stainless steel bar allergy. Level III Treatment Study and Study of Diagnostic Test. Copyright © 2017 Elsevier Inc. All rights reserved.

EMI Shielding Performance For Varies Frequency by Metal Plating on Mold Compound

Directory of Open Access Journals (Sweden)

Min Fee Tai

2017-07-01

Full Text Available Conformal metalization on mold compound offers new possibility for IC package design to improve features such as rigidization of the flexible core, heat sink capability, 3D-circuit patterning and the electromagnetic interference (EMI shielding. With the unique processes, the fabrication technology had enabled to achieve the high reliable performance and had passed the electrical test. Following research after the reliability concern, this paper further study the shielding effectiveness of varying coating thickness with respect to laboratory simulated EMI condition, using radio frequency from 10MHz to 5.8 GHz. Different metal namely pure nickel, nickel-phosphorous and pure plated copper are studied for their effectiveness of EMI sheilding. Our first result showed over 35-40dB of shielding effectiveness is achievable on high frequency 868-5800MHz. Nevertheless on low frequency of 10MHz, the shielding effectiveness achievement is below than 25dB. To overcome the shielding need for lower frequency, we further expanded our test by choosing ferromagentic material Nicke/Ironl-alloy in combination with thick copper plating. With this new metal combination, EMI shielding effectiveness for lower frequency is improved to 40dB.

Effects of selected bioactive food compounds on human white adipocyte function

DEFF Research Database (Denmark)

Björk, Christel; Wilhelm, Uta; Mandrup, Susanne

2016-01-01

BACKGROUND: Previous studies suggest that intake of specific bioactive compounds may have beneficial clinical effects on adipose tissue partly due to their anti-inflammatory and insulin-sensitizing properties. With the overall aim to contribute to better understanding of the mechanisms of selecte...... uptake albeit only with the combination of DHA and AC. Taken together, our results may link the reported health benefits of the selected bioactives on metabolic disorders such as insulin resistance, hypertension and dyslipidemia to effects on white adipocytes....

Application of humic compounds for remediation of soils contaminated with heavy metals: the benefits and risks

Science.gov (United States)

Motuzova, Galina; Barsova, Natalia; Stepanov, Andrey; Kiseleva, Violetta; Kolchanova, Ksenia; Starkova, Irina; Karpukhin, Mikhail

2015-04-01

Applicability of humic compound (HC) "Extra" (potassium humate produced from coal) was studied to remediate soils contaminated with copper in model experiments. Field experiments were carried out in 10-litter plastic containers. The upper layer was prepared as a mixture of loam (pH=5.3), sand (pH=7.4) and peat(pH=5.5). It was underlain consequently by loam and gravel. To study water migration we installed lysimeters. The experiment was conducted in 3 variants: 1) control, 2) control+Cu, 3) control+Cu+HC. Copper was applied in the form of dry powder (CuSO4*5H2O) over the upper layer of the soil column in a concentration of copper equaling to 1000 mg/kg. Total concentration of copper was determined by ICP AAS, its free ions was measured with the help of ion-selective electrode. Humic compound was sprayed on the surface in liquid form. The vessels stayed outdoors from July to October 2014 with additional watering in dry periods. Analysis of lysimetric waters obtained from this model field experiment revealed significant impact of pH. Application of the humic compound produces almost 5 times higher content of soluble organic substances than in the variant without it, and in the first portions of lysimetric waters the difference is 20-fold. Generation of extra organic content in soluble form was accompanied by the 2-6 times increase of the water soluble copper yield. However the content of the free copper ions in lysimetric waters in case of addition of the potassium humate was negligible, because almost all copper was bounded with water-soluble organic substances. The copper content in water extract from the top layer of soil in the variant with HC was about 1 mg/l, that was 2 times higher than without HC. The content of water-soluble organic carbon in HC variant was 100 mg/L, and without HC was 10 times lower (10 mg/l). The water extract from soils enriched in HC was passed through a column filled with weakly basic anion exchange resin DEAE (Cl-form), the eluate was

Study of the catalytic selectivity of an aqueous two-component polyurethane system by ftir spectroscopy

Directory of Open Access Journals (Sweden)

Stamenković Jakov V.

2003-01-01

Full Text Available The difficulty in formulating a two component waterborne polyurethane, is the isocyanate-water side reaction, which can lead to gassing/foaming, loss of isocyanate functionality, low gloss and a reduced pot life. To compensate for this side reaction, these formulations usually contain a large excess of isocyanate. Tin compounds, especially dibutyltin dilaurate, are widely used in coatings as catalysts for the isocyanate/hydroxyl reaction. Because of the high aquatic toxicity of some organotin compounds, there has been an attempt to ban organotin compounds from all coating applications. As a general rule, organotin catalysts are not selective, they catalyze the reaction of isocyanates with both hydroxyl groups and water and also catalyze the hydrolysis of ester groups. One novel approach to control the water side reaction is the use of catalysts which selectively catalyze the isocyanate-polyol reaction and not the isocyanate-water reaction. The selectivity of a variety of metal catalysts (metal octoates, metal acetylacetonates and mangan chelates with mixed ligands to catalyze the preferred reaction was measured using the FTIR method.

The influence of coordination geometry and valency on the K-edge absorption near edge spectra of selected chromium compounds

Energy Technology Data Exchange (ETDEWEB)

Pantelouris, A.; Modrow, H.; Pantelouris, M.; Hormes, J.; Reinen, D

2004-05-10

X-ray absorption spectra at the chromium K-edge are reported for a number of selected chromium compounds of known chemical structure. The spectra were obtained with use of synchrotron radiation available at the ELectron Stretcher Accelerator ELSA in Bonn. The compounds studied include the tetrahedrally coordinated compounds Ca{sub 2}Ge{sub 0.8}Cr{sub 0.2}O{sub 4}, Ba{sub 2}Ge{sub 0.1}Cr{sub 0.9}O{sub 4}, Sr{sub 2}CrO{sub 4}, Ca{sub 2}(PO{sub 4}){sub x}(CrO{sub 4}){sub 1-x}Cl (x=0.25,0.5), Ca{sub 5}(CrO{sub 4}){sub 3}Cl, CrO{sub 3}, the octahedrally coordinated compounds Cr(II)-acetate, CrCl{sub 3}, CrF{sub 3}, Cr{sub 2}O{sub 3}, KCr(SO{sub 4}){sub 2} {center_dot} 12H{sub 2}O, CrO{sub 2} and cubic coordinated metallic chromium. In these compounds chromium exhibits a wide range of formal oxidation states (0 to VI). The absorption features in the near edge region are shown to be characteristic of the spatial environment of the absorbing atom. The occurrence of a single pre-edge line easily allows one to distinguish between tetrahedral and octahedral coordination geometry, whereas the energy position of the absorption edge is found to be very sensitive to the valency of the excited chromium atom. Calculations of the ionisation potential of Cr in different oxidation states using the non-relativistic Hartree-Fock method (Froese-Fischer) confirm that the ionisation limit shifts to higher energy with increasing Cr valency. More detailed information on the electronic structure of the different compounds is gained by real-space full multiple scattering calculations using the FEFF8 code.

Parameters in selective laser melting for processing metallic powders

Science.gov (United States)

Kurzynowski, Tomasz; Chlebus, Edward; Kuźnicka, Bogumiła; Reiner, Jacek

2012-03-01

The paper presents results of studies on Selective Laser Melting. SLM is an additive manufacturing technology which may be used to process almost all metallic materials in the form of powder. Types of energy emission sources, mainly fiber lasers and/or Nd:YAG laser with similar characteristics and the wavelength of 1,06 - 1,08 microns, are provided primarily for processing metallic powder materials with high absorption of laser radiation. The paper presents results of selected variable parameters (laser power, scanning time, scanning strategy) and fixed parameters such as the protective atmosphere (argon, nitrogen, helium), temperature, type and shape of the powder material. The thematic scope is very broad, so the work was focused on optimizing the process of selective laser micrometallurgy for producing fully dense parts. The density is closely linked with other two conditions: discontinuity of the microstructure (microcracks) and stability (repeatability) of the process. Materials used for the research were stainless steel 316L (AISI), tool steel H13 (AISI), and titanium alloy Ti6Al7Nb (ISO 5832-11). Studies were performed with a scanning electron microscope, a light microscopes, a confocal microscope and a μCT scanner.

Tuning of CO2 Reduction Selectivity on Metal Electrocatalysts.

Science.gov (United States)

Wang, Yuhang; Liu, Junlang; Wang, Yifei; Al-Enizi, Abdullah M; Zheng, Gengfeng

2017-11-01

Climate change, caused by heavy CO 2 emissions, is driving new demands to alleviate the rising concentration of atmospheric CO 2 levels. Enlightened by the photosynthesis of green plants, photo(electro)chemical catalysis of CO 2 reduction, also known as artificial photosynthesis, is emerged as a promising candidate to address these demands and is widely investigated during the past decade. Among various artificial photosynthetic systems, solar-driven electrochemical CO 2 reduction is widely recognized to possess high efficiencies and potentials for practical application. The efficient and selective electroreduction of CO 2 is the key to the overall solar-to-chemical efficiency of artificial photosynthesis. Recent studies show that various metallic materials possess the capability to play as electrocatalysts for CO 2 reduction. In order to achieve high selectivity for CO 2 reduction products, various efforts are made including studies on electrolytes, crystal facets, oxide-derived catalysts, electronic and geometric structures, nanostructures, and mesoscale phenomena. In this Review, these methods for tuning the selectivity of CO 2 electrochemical reduction of metallic catalysts are summarized. The challenges and perspectives in this field are also discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Selective cleavage of the C(α)-C(β) linkage in lignin model compounds via Baeyer-Villiger oxidation.

Science.gov (United States)

Patil, Nikhil D; Yao, Soledad G; Meier, Mark S; Mobley, Justin K; Crocker, Mark

2015-03-21

Lignin is an amorphous aromatic polymer derived from plants and is a potential source of fuels and bulk chemicals. Herein, we present a survey of reagents for selective stepwise oxidation of lignin model compounds. Specifically, we have targeted the oxidative cleavage of Cα-Cβ bonds as a means to depolymerize lignin and obtain useful aromatic compounds. In this work, we prepared several lignin model compounds that possess structures, characteristic reactivity, and linkages closely related to the parent lignin polymer. We observed that selective oxidation of benzylic hydroxyl groups, followed by Baeyer-Villiger oxidation of the resulting ketones, successfully cleaves the Cα-Cβ linkage in these model compounds.

New pathway for the formation of metallic cubic phase Ge-Sb-Te compounds induced by an electric current.

Science.gov (United States)

Park, Yong-Jin; Cho, Ju-Young; Jeong, Min-Woo; Na, Sekwon; Joo, Young-Chang

2016-02-23

The novel discovery of a current-induced transition from insulator to metal in the crystalline phase of Ge2Sb2Te5 and GeSb4Te7 have been studied by means of a model using line-patterned samples. The resistivity of cubic phase Ge-Sb-Te compound was reduced by an electrical current (~1 MA/cm(2)), and the final resistivity was determined based on the stress current density, regardless of the initial resistivity and temperature, which indicates that the conductivity of Ge-Sb-Te compound can be modulated by an electrical current. The minimum resistivity of Ge-Sb-Te materials can be achieved at high kinetic rates by applying an electrical current, and the material properties change from insulating to metallic behavior without a phase transition. The current-induced metal transition is more effective in GeSb4Te7 than Ge2Sb2Te5, which depends on the intrinsic vacancy of materials. Electromigration, which is the migration of atoms induced by a momentum transfer from charge carriers, can easily promote the rearrangement of vacancies in the cubic phase of Ge-Sb-Te compound. This behavior differs significantly from thermal annealing, which accompanies a phase transition to the hexagonal phase. This result suggests a new pathway for modulating the electrical conductivity and material properties of chalcogenide materials by applying an electrical current.

Gases and carbon in metals. Pt. 14

International Nuclear Information System (INIS)

Jehn, H.; Speck, H.; Hehn, W.; Fromm, E.; Hoerz, G.

1981-01-01

This issue is part of a series of data on 'Gases and Carbon in Metals' which supplements the data compilation in the book 'Gase und Kohlenstoff in Metallen' (Gases and Carbon in Metals), edited by E. Fromm and E. Gebhardt, Springer-Verlag, Berlin 1976. The present survey includes results from papers published after the copy deadline and recommends critically selected data. Furthermore, it comprises a bibliography of relevant literature. For each element, firstly data on binary systems are presented, starting with hydrogen and followed by carbon, nitrogen, oxygen, and rare gases. Within one metal-metalloid system the data are listed under topics such as solubility, solubility limit, dissociation pressure of compounds, vapour pressure of volatile oxides, thermodynamic data, diffusion, transport parameters (effective valence, heat of transport), permeation of gases through metals, gas absorption and gas desorption kinetics, compound formation kinetics, precipitation kinetics, and property changes. Following the data on binary systems, the data of ternary systems are presented, beginning with systems which contain one metal and two gases or one gas and carbon and continuing with systems with two metals and one gas or carbon. (orig./GE)

Beta-galactosidase catalyzed selective galactosylation of aromatic compounds.

Science.gov (United States)

Bridiau, Nicolas; Taboubi, Selma; Marzouki, Nejib; Legoy, Marie Dominique; Maugard, Thierry

2006-01-01

A new approach to galacto-oligosaccharides and galacto-conjugates synthesis performed by the beta-galactosidase from Kluyveromyces lactis is reported. The enzymatic galactosylation of eight kinds of adsorbed aromatic primary alcohols, in particular the two drugs guaifenesin and chlorphenesin, gave the corresponding beta-D-galacto-pyranosides in yields ranging between approximately 10% and 96%. For the first time, we have showed that the adsorption of acceptor substrates onto solid supports such as silica gel influences the yield and the selectivity of galacto-conjugates synthesis. In particular, we observed that adsorption of acceptor favored the synthesis of digalactosylated compounds.

Fabrication of metal/semiconductor nanocomposites by selective laser nano-welding.

Science.gov (United States)

Yu, Huiwu; Li, Xiangyou; Hao, Zhongqi; Xiong, Wei; Guo, Lianbo; Lu, Yongfeng; Yi, Rongxing; Li, Jiaming; Yang, Xinyan; Zeng, Xiaoyan

2017-06-01

A green and simple method to prepare metal/semiconductor nanocomposites by selective laser nano-welding metal and semiconductor nanoparticles was presented, in which the sizes, phases, and morphologies of the components can be maintained. Many types of nanocomposites (such as Ag/TiO 2 , Ag/SnO 2 , Ag/ZnO 2 , Pt/TiO 2 , Pt/SnO 2 , and Pt/ZnO) can be prepared by this method and their corresponding performances were enhanced.

Selective Extraction of Perrhenate and Pertechnetate by New Macrocyclic Compounds

International Nuclear Information System (INIS)

Paviet-Hartmann, Patricia; Horkley, Jared; Wolfrom, Earle; Pak, Joshua

2008-01-01

The long half-life of technetium-99 and its ability to form an anionic species makes it a major concern when considering long-term disposal of high-level radioactive waste. Furthermore, as its most stable species in the environment, the pertechnetate ion, TcO 4 - is highly mobile and is considered as a long-term hazard in nuclear waste disposal. There is a need for the development of new extractant systems, such as systems based on crown ethers that may serve to selectively extract and separate this long lived radionuclide from different streams for potential industrial application. In this paper, we are reporting the design and synthesis of new macrocyclic compounds to selectively extract technetium and rhenium from complex mixtures. Preliminary tests performed for the selective extraction of pertechnetate and perrhenate are presented. (authors)

Isotopically modified compounds

International Nuclear Information System (INIS)

Kuruc, J.

2009-01-01

In this chapter the nomenclature of isotopically modified compounds in Slovak language is described. This chapter consists of following parts: (1) Isotopically substituted compounds; (2) Specifically isotopically labelled compounds; (3) Selectively isotopically labelled compounds; (4) Non-selectively isotopically labelled compounds; (5) Isotopically deficient compounds.

Heavy metal content of selected African leafy vegetables planted in ...

African Journals Online (AJOL)

Heavy metal content of selected African leafy vegetables planted in urban and peri-urban Nairobi, Kenya. ... African Journal of Environmental Science and Technology ... Government clean-up activities and monitoring of waste disposal is ...

Low concentrations of metal mixture exposures have adverse effects on selected biomarkers of Xenopus laevis tadpoles

Energy Technology Data Exchange (ETDEWEB)

Yologlu, Ertan, E-mail: ertanyologlu82@gmail.com [Adiyaman University, Faculty of Education, Department of Science Education, 02040 Adiyaman (Turkey); Ozmen, Murat [Inonu University, Laboratory of Environmental Toxicology, Department of Biology, Faculty of Arts & Science, 44280 Malatya (Turkey)

2015-11-15

Highlights: • Selected metal mixtures were evaluated for toxicity of safety limit concentrations. • Xenopus laevis tadpoles were used as model test organism. • Combinations of LC{sub 50} and LC{sub 50}/2 caused 100% lethality for some metals. • Metals did not change metallothionein levels in low concentrations. • Selected enzyme activities showed induction after low concentration exposures. - Abstract: Polluted ecosystems may contain mixtures of metals, such that the combinations of metals, even in low concentrations, may cause adverse effects. In the present study, we focused on toxic effects of mixtures of selected metals, the LC{sub 50} values, and also their safety limit in aquatic systems imposed by the European legislation using a model organism. Xenopus laevis tadpoles were used as test organisms. They were exposed to metals or their combinations due to 96-h LC{sub 50} values. Glutathione S-transferase (GST), glutathione reductase (GR), acetylcholinesterase (AChE), carboxylesterase (CaE), glutathione peroxidase (GPx), and catalase (CAT) levels were evaluated. Metallothionein concentrations were also determined. The LC{sub 50}s for Cd, Pb, and Cu were calculated as 5.81 mg AI/L, 123.05 mg AI/L, and 0.85 mg AI/L, respectively. Low lethality ratios were observed with unary exposure of each metal in lower concentrations. Double or triple combinations of LC{sub 50} and LC{sub 50}/2 concentrations caused 100% lethality with Cd + Cu and Pb + Cd + Cu mixtures, while the Pb + Cu mixture also caused high lethal ratios. The selected enzyme activities were significantly affected by metals or mixtures, and dose-related effects were determined. The metallothionein levels generally increased as related to concentration in unary metals and mixtures. Acceptable limit values of unary metals and mixtures did not significantly change metallothionein levels. The results suggest that oxidative stress-related mechanisms are involved in the toxicity induced by selected

Selective Extraction of Perrhenate and Pertechnetate by New Macrocyclic Compounds

Energy Technology Data Exchange (ETDEWEB)

Paviet-Hartmann, Patricia; Horkley, Jared; Wolfrom, Earle [Idaho State University/Idaho National Laboratory, 1776 Science Center Drive, Idaho Falls, ID 83402 (United States); Pak, Joshua [Idaho State University, 921 S. 8th Avenue, Pocatello, ID 83209 (United States)

2008-07-01

The long half-life of technetium-99 and its ability to form an anionic species makes it a major concern when considering long-term disposal of high-level radioactive waste. Furthermore, as its most stable species in the environment, the pertechnetate ion, TcO{sub 4}{sup -} is highly mobile and is considered as a long-term hazard in nuclear waste disposal. There is a need for the development of new extractant systems, such as systems based on crown ethers that may serve to selectively extract and separate this long lived radionuclide from different streams for potential industrial application. In this paper, we are reporting the design and synthesis of new macrocyclic compounds to selectively extract technetium and rhenium from complex mixtures. Preliminary tests performed for the selective extraction of pertechnetate and perrhenate are presented. (authors)

Ion spectra of the metal vapor vacuum arc ion source with compound and alloy cathodes

Science.gov (United States)

Sasaki, Jun; Brown, Ian G.

1990-01-01

In metal vapor vacuum arc (MEVVA) ion sources, vacuum arc plasma with cathodes of single, pure elements has been utilized for the production of metal ions. In this study, we have investigated the charge state distributions of ions produced in vacuum arc plasmas in a MEVVA ion source for the case when the cathode is an alloy or a compound material. The ion charge state spectra were analyzed by means of a time-of-flight apparatus. We have compared the ion spectra for a cathode of an alloy or a compound material with its constituent elements: TiC/TiN/TiO2/Ti/C, SiC/Si/C, WC/W/C U/UN/(UN-ZrC)/Zr/C, and brass/Zn/Cu. We find that the MEVVA produces ions of all constituent elements in the compound and the alloy cathodes. The charge state distribution of each element differs, however, from the charge state distribution obtained in the vacuum arc with a cathode made of the pure, single constituent element. Fractional values of the total ion numbers of each constituent element in the extracted beam depart from the stoichiometry of the elements in the cathode material. In an operation with a TiC cathode, we irradiated a 304 stainless-steel plate with the extracted beam. Results from glow-discharge spectroscopy (GDS) of the surface show that both titanium and carbon are implanted in the substrate after the irradiation.

Data on heavy metals and selected anions in the Persian popular herbal distillates

Directory of Open Access Journals (Sweden)

Mozhgan Keshtkar

2016-09-01

Full Text Available In this data article, we determined the concentration levels of heavy metals including Pb, Co, Cd, Mn, Mg, Fe and Cu as well as selected anions including NO3− , NO2−, PO4−3 and SO4−2 in the most used and popular herbal distillates in Iran. It is well known that heavy metals may pose a serious health hazard due to their bioaccumulation throughout the trophic chain (“Heavy metals (Cd, Cu, Ni and Pb content in two fish species of Persian Gulf in Bushehr Port, Iran” (Dobaradaran et al., 2013 [1]; “Comparative investigation of heavy metal, trace, and macro element contents in commercially valuable fish species harvested off from the Persian Gulf” (Abadi et al., 2015 [2] as well as some other environmental pollutions, “Assessment of sediment quality based on acid-volatile sulfide and simultaneously extracted metals in heavily industrialized area of Asaluyeh, Persian Gulf: concentrations, spatial distributions, and sediment bioavailability/toxicity” (Arfaeinia et al., 2016 [3]. The concentration levels of heavy metals and anions in herbal distillates samples were determined using flame atomic absorption spectrometry (FAAS, Varian AA240, Australia and a spectrophotometer (M501 Single Beam Scanning UV/VIS, UK respectively. Keywords: Daily intake, Herbal distillates, Heavy metals, Selected anions

Precious Metals Recovery from Electroplating Wastewater: A Review

Science.gov (United States)

Azmi, A. A.; Jai, J.; Zamanhuri, N. A.; Yahya, A.

2018-05-01

Metal bearing electroplating wastewater posts great health and environmental concerns, but could also provide opportunities for precious and valuable metal recovery, which can make the treatment process more cost-effective and sustainable. Current conventional electroplating wastewater treatment and metal recovery methods include chemical precipitation, coagulation and flocculation, ion exchange, membrane filtration, adsorption, electrochemical treatment and photocatalysis. However, these physico-chemical methods have several disadvantages such as high initial capital cost, high operational cost due to expensive chemical reagents and electricity supply, generation of metal complexes sludge which requires further treatment, ineffective in diluted and/or concentrated wastewater, low precious metal selectivity, and slow recovery process. On the other hand, metal bio-reduction assisted by bioactive phytochemical compounds extracted from plants and plant parts is a new found technology explored by several researchers in recent years aiming to recover precious and valuable metals from secondary sources mainly industrial wastewater by utilizing low-cost and eco-friendly biomaterials as reagents. Extract of plants contains polyphenolic compounds which have great antioxidant properties and reducing capacities, able to reduce metal ions into zerovalent metal atoms and stabilize the metal particles formed. This green bio-recovery method has a value added in their end products since the metals are recovered in nano-sized particles which are more valuable and have high commercial demand in other fields ranging from electrochemistry to medicine.

Hydrometallurgical Approach for Leaching of Metals from Copper Rich Side Stream Originating from Base Metal Production

Directory of Open Access Journals (Sweden)

Udit Surya Mohanty

2018-01-01

Full Text Available Pyrometallurgical metal production results in side streams, such as dusts and slags, which are carriers of metals, though commonly containing lower metal concentrations compared to the main process stream. In order to improve the circular economy of metals, selective leaching of copper from an intermediate raw material originating from primary base metal production plant was investigated. The raw material investigated was rich in Cu (12.5%, Ni (2.6%, Zn (1.6%, and Fe (23.6% with the particle size D80 of 124 µm. The main compounds present were nickel ferrite (NiFe2O4, fayalite (Fe2SiO4, cuprite (Cu2O, and metallic copper. Leaching was studied in 16 different solutions. The results revealed that copper phases could be dissolved with high yield (>90% and selectivity towards nickel (Cu/Ni > 7 already at room temperature with the following solutions: 0.5 M HCl, 1.5 M HCl, 4 M NaOH, and 2 M HNO3. A concentration of 4 M NaOH provided a superior selectivity between Cu/Ni (340 and Cu/Zn (51. In addition, 1–2 M HNO3 and 0.5 M HCl solutions were shown to result in high Pb dissolution (>98%. Consequently, 0.5 M HCl leaching is suggested to provide a low temperature, low chemical consumption method for selective copper removal from the investigated side stream, resulting in PLS (pregnant leach solution which is a rich in Cu and lead free residue, also rich in Ni and Fe.

Structure-activity relationship of 9-methylstreptimidone, a compound that induces apoptosis selectively in adult T-cell leukemia cells.

Science.gov (United States)

Takeiri, Masatoshi; Ota, Eisuke; Nishiyama, Shigeru; Kiyota, Hiromasa; Umezawa, Kazuo

2012-01-01

We previously reported that 9-methylstreptimidone, a piperidine compound isolated from a culture filtrate of Streptomyces, induces apoptosis selectively in adult T-cell leukemia cells. It was screened for a compound that inhibits LPS-induced NF-kappaB and NO production in mouse macrophages. However, 9-methystreptimidone is poorly obtained from the producing microorganism and difficult to synthesize. Therefore, in the present research, we studied the structure-activity relationship to look for new selective inhibitors. We found that the structure of the unsaturated hydrophobic portion of 9-methylstreptimidone was essential for the inhibition of LPS-induced NO production. Among the 9-methylstreptimidone-related compounds tested, (+/-)-4,alpha-diepi-streptovitacin A inhibited NO production in macrophage-like cells as potently as 9-methylstreptimidone and without cellular toxicity. Moreover, this compound selectively induced apoptosis in adult T-cell leukemia MT-1 cells.

A combined Fisher and Laplacian score for feature selection in QSAR based drug design using compounds with known and unknown activities.

Science.gov (United States)

Valizade Hasanloei, Mohammad Amin; Sheikhpour, Razieh; Sarram, Mehdi Agha; Sheikhpour, Elnaz; Sharifi, Hamdollah

2018-02-01

Quantitative structure-activity relationship (QSAR) is an effective computational technique for drug design that relates the chemical structures of compounds to their biological activities. Feature selection is an important step in QSAR based drug design to select the most relevant descriptors. One of the most popular feature selection methods for classification problems is Fisher score which aim is to minimize the within-class distance and maximize the between-class distance. In this study, the properties of Fisher criterion were extended for QSAR models to define the new distance metrics based on the continuous activity values of compounds with known activities. Then, a semi-supervised feature selection method was proposed based on the combination of Fisher and Laplacian criteria which exploits both compounds with known and unknown activities to select the relevant descriptors. To demonstrate the efficiency of the proposed semi-supervised feature selection method in selecting the relevant descriptors, we applied the method and other feature selection methods on three QSAR data sets such as serine/threonine-protein kinase PLK3 inhibitors, ROCK inhibitors and phenol compounds. The results demonstrated that the QSAR models built on the selected descriptors by the proposed semi-supervised method have better performance than other models. This indicates the efficiency of the proposed method in selecting the relevant descriptors using the compounds with known and unknown activities. The results of this study showed that the compounds with known and unknown activities can be helpful to improve the performance of the combined Fisher and Laplacian based feature selection methods.

Metal alkyls programmed to generate metal alkylidenes by α-H abstraction: prognosis from NMR chemical shift† †Electronic supplementary information (ESI) available: Experimental and computational details, NMR spectra, results of NMR calculations and NCS analysis, graphical representation of shielding tensors, molecular orbital diagrams of selected compounds, optimized structures for all calculated species. See DOI: 10.1039/c7sc05039a

Science.gov (United States)

Gordon, Christopher P.; Yamamoto, Keishi; Searles, Keith; Shirase, Satoru

2018-01-01

Metal alkylidenes, which are key organometallic intermediates in reactions such as olefination or alkene and alkane metathesis, are typically generated from metal dialkyl compounds [M](CH2R)2 that show distinctively deshielded chemical shifts for their α-carbons. Experimental solid-state NMR measurements combined with DFT/ZORA calculations and a chemical shift tensor analysis reveal that this remarkable deshielding originates from an empty metal d-orbital oriented in the M–Cα–Cα′ plane, interacting with the Cα p-orbital lying in the same plane. This π-type interaction inscribes some alkylidene character into Cα that favors alkylidene generation via α-H abstraction. The extent of the deshielding and the anisotropy of the alkyl chemical shift tensors distinguishes [M](CH2R)2 compounds that form alkylidenes from those that do not, relating the reactivity to molecular orbitals of the respective molecules. The α-carbon chemical shifts and tensor orientations thus predict the reactivity of metal alkyl compounds towards alkylidene generation. PMID:29675237

Some reduced ternary and quaternary oxides of molybdenum. A family of compounds with strong metal-metal bonds

International Nuclear Information System (INIS)

Torardi, C.C.; McCarley, R.E.

1981-01-01

Several new, reduced ternary and quaternary oxides of molybdenum are reported, each containing molybdenum in an average oxidation state 2 sealed in Mo tubes held at 1100 0 C for ca. 7 days. Refinement of the substructure of the new compound Ba 0 62 Mo 4 O 6 was based on an orthorhombic cells, with a = 9.509(2), b = 9.825(2), c = 2.853(1) A, Z = 2 in space group Pbam; weak supercell reflections indicate the true structure has c = 8(2.853) A. The chief structural feature is closely related to that of NaMo 4 O 6 which consists of infinite chains of Mo 6 octahedral clusters fused on opposite edges, bridged on the outer edges by O atoms and crosslinked by Mo-O-Mo bonding to create four-sided tunnels in which the Ba 2+ ions are located. The structure of Ba 1 13 Mo 8 O 16 is triclinic, a = 7.311(1), b = 7.453(1), c = 5.726(1) A, α = 101.49(2), β = 99.60(2), γ = 89.31(2) 0 , Z = 1, space group P1. It is a low-symmetry, metal-metal bonded variant of the hollandite structure, in which two different infinite chains, built up from Mo 4 O 8 2- and Mo 4 O 8 0 26- cluster units, respectively, are interlinked via Mo-O-Mo bridge bonding to create again four-sided tunnels in which the Ba 2+ ions reside. Other compounds prepared and characterized by analyses and x-ray powder diffraction data are Pb/sub x/Mo 4 O 6 (x approx. 0.6), LiZn 2 Mo 3 O 8 , , CaMo 5 O 8 , K 2 Mo 12 O 19 , and Na 2 Mo 12 O 19

Chromatographic methods for determination of metals as chelate compounds with heterocyclic azo reagents

International Nuclear Information System (INIS)

Basova, E.M.; Bol'shova, T.A.; Shpigun, O.A.; Ivanov, V.M.

1993-01-01

Methods for separation and concentration of transition metals as well as cadmium in form of chelates with heterocyclic azo compounds namely, PAN(1-(2-pyridylaso)-2-naphthol), PAR(4-(2-pyridylazo)-resorcin), Br-PAAP (2-(5-bromine-2-pyridylazo)-5-diethyl aminophenol) are considered. The Br-PAAP reagent is the most sensitive and widely-applied one in extraction and highly-efficient liquid chromatography. Methods of sorption concentration with subsequent element determination directly on the sorbent without microelements separation or destruction are the most promissing ones

Bioavailability of Heavy Metals in Soil: Impact on Microbial Biodegradation of Organic Compounds and Possible Improvement Strategies

Science.gov (United States)

Olaniran, Ademola O.; Balgobind, Adhika; Pillay, Balakrishna

2013-01-01

Co-contamination of the environment with toxic chlorinated organic and heavy metal pollutants is one of the major problems facing industrialized nations today. Heavy metals may inhibit biodegradation of chlorinated organics by interacting with enzymes directly involved in biodegradation or those involved in general metabolism. Predictions of metal toxicity effects on organic pollutant biodegradation in co-contaminated soil and water environments is difficult since heavy metals may be present in a variety of chemical and physical forms. Recent advances in bioremediation of co-contaminated environments have focussed on the use of metal-resistant bacteria (cell and gene bioaugmentation), treatment amendments, clay minerals and chelating agents to reduce bioavailable heavy metal concentrations. Phytoremediation has also shown promise as an emerging alternative clean-up technology for co-contaminated environments. However, despite various investigations, in both aerobic and anaerobic systems, demonstrating that metal toxicity hampers the biodegradation of the organic component, a paucity of information exists in this area of research. Therefore, in this review, we discuss the problems associated with the degradation of chlorinated organics in co-contaminated environments, owing to metal toxicity and shed light on possible improvement strategies for effective bioremediation of sites co-contaminated with chlorinated organic compounds and heavy metals. PMID:23676353

Bioavailability of Heavy Metals in Soil: Impact on Microbial Biodegradation of Organic Compounds and Possible Improvement Strategies

Directory of Open Access Journals (Sweden)

Balakrishna Pillay

2013-05-01

Full Text Available Co-contamination of the environment with toxic chlorinated organic and heavy metal pollutants is one of the major problems facing industrialized nations today. Heavy metals may inhibit biodegradation of chlorinated organics by interacting with enzymes directly involved in biodegradation or those involved in general metabolism. Predictions of metal toxicity effects on organic pollutant biodegradation in co-contaminated soil and water environments is difficult since heavy metals may be present in a variety of chemical and physical forms. Recent advances in bioremediation of co-contaminated environments have focussed on the use of metal-resistant bacteria (cell and gene bioaugmentation, treatment amendments, clay minerals and chelating agents to reduce bioavailable heavy metal concentrations. Phytoremediation has also shown promise as an emerging alternative clean-up technology for co-contaminated environments. However, despite various investigations, in both aerobic and anaerobic systems, demonstrating that metal toxicity hampers the biodegradation of the organic component, a paucity of information exists in this area of research. Therefore, in this review, we discuss the problems associated with the degradation of chlorinated organics in co-contaminated environments, owing to metal toxicity and shed light on possible improvement strategies for effective bioremediation of sites co-contaminated with chlorinated organic compounds and heavy metals.

Study of surface modifications for improved selected metal (II-VI) semiconductor based devices

Science.gov (United States)

Blomfield, Christopher James

Metal-semiconductor contacts are of fundamental importance to the operation of all semiconductor devices. There are many competing theories of Schottky barrier formation but as yet no quantitative predictive model exists to adequately explain metal-semiconductor interfaces. The II-VI compound semiconductors CdTe, CdS and ZnSe have recently come to the fore with the advent of high efficiency photovoltaic cells and short wavelength light emitters. Major problems still exist however in forming metal contacts to these materials with the desired properties. This work presents results which make a significant contribution to the theory of metal/II-VI interface behaviour in terms of Schottky barriers to n-type CdTe, CdS and ZnSe.Predominantly aqueous based wet chemical etchants were applied to the surfaces of CdTe, CdS and ZnSe which were subsequently characterised by X-ray photoelectron spectroscopy. The ionic nature of these II-VI compounds meant that they behaved as insoluble salts of strong bases and weak acids. Acid etchants induced a stoichiometric excess of semiconductor anion at the surface which appeared to be predominantly in the elemental or hydrogenated state. Alkaline etchants conversely induced a stoichiometric excess of semiconductor cation at the surface which appeared to be in an oxidised state.Metal contacts were vacuum-evaporated onto these etched surfaces and characterised by current-voltage and capacitance-voltage techniques. The surface preparation was found to have a clear influence upon the electrical properties of Schottky barriers formed to etched surfaces. Reducing the native surface oxide produced near ideal Schottky diodes. An extended study of Au, Ag and Sb contacts to [mathematical formula] substrates again revealed the formation of several discrete Schottky barriers largely independent of the metal used; for [mathematical formula]. Deep levels measured within this study and those reported in the literature led to the conclusion that Fermi

Development of Surface-Modified Polyacrylonitrile Fibers and Their Selective Sorption Behavior of Precious Metals

Directory of Open Access Journals (Sweden)

Areum Lim

2016-11-01

Full Text Available The purpose of this study was to design a powerful fibrous sorbent for recovering precious metals such as Pd(II and Pt(IV, and moreover for identifying its selectivity toward Pd(II or Pt(IV from a binary metal solution. For the development of the sorbent, polyacrylonitrile (PAN was selected as a model textile because its morphological property (i.e., thin fiber form is suitable for fast adsorption processes, and a high amount of PAN has been discharged from industrial textile factories. The PAN fiber was prepared by spinning a PAN–dimethylsulfoxide mixture into distilled water, and then its surface was activated through amidoximation so that the fiber surface could possess binding sites for Pd(II and Pt(IV. Afterwards, by Fourier-transform infrared (FT-IR and scanning electron microscopy (SEM analyses, it was confirmed that the amidoximation reaction successfully occurred. The surface-activated fiber, designated as PAN–oxime fiber, was used to adsorb and recover precious metals. In the experiment results, it was clearly observed that adsorption capacity of PAN–oxime fiber was significantly enhanced compared to the raw material form. Actually, the raw material does not have sorption capacity for the metals. In a comparison study with commercial sorbent (Amberjet™ 4200, it was found that adsorption capacity of PAN–oxime was rather lower than that of Amberjet™ 4200, however, in the aspects of sorption kinetics and metal selectivity, the new sorbent has much faster and better selectivity.

Selective removal of heavy metals from metal-bearing wastewater in a cascade line reactor.

Science.gov (United States)

Pavlović, Jelena; Stopić, Srećko; Friedrich, Bernd; Kamberović, Zeljko

2007-11-01

This paper is a part of the research work on 'Integrated treatment of industrial wastes towards prevention of regional water resources contamination - INTREAT' the project. It addresses the environmental pollution problems associated with solid and liquid waste/effluents produced by sulfide ore mining and metallurgical activities in the Copper Mining and Smelting Complex Bor (RTB-BOR), Serbia. However, since the minimum solubility for the different metals usually found in the polluted water occurs at different pH values and the hydroxide precipitates are amphoteric in nature, selective removal of mixed metals could be achieved as the multiple stage precipitation. For this reason, acid mine water had to be treated in multiple stages in a continuous precipitation system-cascade line reactor. All experiments were performed using synthetic metal-bearing effluent with chemical a composition similar to the effluent from open pit, Copper Mining and Smelting Complex Bor (RTB-BOR). That effluent is characterized by low pH (1.78) due to the content of sulfuric acid and heavy metals, such as Cu, Fe, Ni, Mn, Zn with concentrations of 76.680, 26.130, 0.113, 11.490, 1.020 mg/dm3, respectively. The cascade line reactor is equipped with the following components: for feeding of effluents, for injection of the precipitation agent, for pH measurements and control, and for removal of the process gases. The precipitation agent was 1M NaOH. In each of the three reactors, a changing of pH and temperature was observed. In order to verify. efficiency of heavy metals removal, chemical analyses of samples taken at different pH was done using AES-ICP. Consumption of NaOH in reactors was 370 cm3, 40 cm3 and 80 cm3, respectively. Total time of the experiment was 4 h including feeding of the first reactor. The time necessary to achieve the defined pH value was 25 min for the first reactor and 13 min for both second and third reactors. Taking into account the complete process in the cascade line

Selective synthesis and characterization of sea urchin-like metallic nickel nanocrystals

International Nuclear Information System (INIS)

Liu Xiaohe; Liang Xudong; Zhang Ning; Qiu Guanzhou; Yi Ran

2006-01-01

Sea urchin-like nanobelt-based and nanorod-based metallic nickel nanocrystals have been selective synthesized via a hydrothermal reduction route in which sodium hydroxide was used as alkaline reagent and aqueous hydrazine (N 2 H 4 .H 2 O) was used as reducing agent. The morphology and structure of final products could be easily controlled by adjust process parameters such as hydrothermal time, reaction temperature and alkaline concentration. Surfactant cetyltrimethylammonium bromide (CTAB) was also important parameter influencing the morphology of the products. The morphology and phase structure of the final products have been investigated by X-ray diffraction, transmission electron microscopy and selected area electron diffraction. The probable formation mechanism of the sea urchin-like metallic nickel nanocrystals was discussed on the basis of the experimental results

Design and fabrication of a mechanical alloying system for preparing intermetallic, nanocrystalline, amorphous and quasicrystalline compounds

International Nuclear Information System (INIS)

Bonifacio M, J.; Iturbe G, J.L.; Castaneda J, G.

2002-01-01

In this work a grinding system was designed and fabricated which allowed to improve the operation conditions in time, frequency, temperature and selection of the grinding media and that allow the contamination decrease of the compounds. By means of this method of mechanical alloying new metallic compounds can be produced, starting from elemental powders, with fine and controlled microstructures. These compounds prepared by this method are going to be used as materials for the hydrogen storage. (Author)

Single site porphyrine-like structures advantages over metals for selective electrochemical CO2 reduction

DEFF Research Database (Denmark)

Bagger, Alexander; Ju, Wen; Varela, Ana Sofia

2017-01-01

Currently, no catalysts are completely selective for the electrochemical CO2 Reduction Reaction (CO2RR). Based on trends in density functional theory calculations of reaction intermediates we find that the single metal site in a porphyrine-like structure has a simple advantage of limiting...... the competing Hydrogen Evolution Reaction (HER). The single metal site in a porphyrine-like structure requires an ontop site binding of hydrogen, compared to the hollow site binding of hydrogen on a metal catalyst surface. The difference in binding site structure gives a fundamental energy-shift in the scaling...... relation of ∼0.3eV between the COOH* vs. H* intermediate (CO2RR vs. HER). As a result, porphyrine-like catalysts have the advantage over metal catalyst of suppressing HER and enhancing CO2RR selectivity....

Method of making a long life high current density cathode from tungsten and iridium powders using a quaternary compound as the impregnant

International Nuclear Information System (INIS)

Branovich, L.E.; Smith, B.; Freemen, G.L.; Eckart, D.W.

1990-01-01

This patent describes a method of making a long life high current density cathode. It is suitable for operation in microwave devices. It is made from tungsten and iridium powders using a quaternary compound including barium, oxygen, a metal selected from the group consisting of osmium, iridium, rhodium, and rhenium, and a metal selected from the group consisting of strontium, calcium, scandium, and titanium as the impregnant

Selective heavy metals removal from waters by amorphous zirconium phosphate: behavior and mechanism.

Science.gov (United States)

Pan, Bingcai; Zhang, Qingrui; Du, Wei; Zhang, Weiming; Pan, Bingjun; Zhang, Qingjian; Xu, Zhengwen; Zhang, Quanxing

2007-07-01

Selective removal of heavy metals from water has been of considerable concern for several decades. In the present study, the amorphous zirconium phosphate (ZrP) was synthesized and characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron micrography (SEM), thermogravimetric analysis (TGA) as well as pH-titration experiments. Uptake of heavy metals including lead, cadmium, and zinc onto ZrP was studied by using a polystyrene sulfonic-acid exchanger D-001 as a reference sorbent and Ca(2+) as a competing cation due to its ubiquity in natural or industrial waters. The results indicated that the uptake of heavy metals onto ZrP is essentially an ion-exchange process and dependent upon solution pH. In comparison with D-001, ZrP exhibited more favorable sorption of heavy metals particularly in terms of high selectivity, as indicated by the distribution coefficients of ZrP even several orders higher than D-001 towards heavy metals when calcium ion coexisted at a high level in solution. The Fourier transform-infrared (FT-IR) spectroscopic investigation indicated that the uptake of calcium, cadmium, and zinc ions onto ZrP is only driven by the electrostatic interaction, while that of lead ion is possibly dependent upon the inner-sphere complex formation with ZrP. XPS results further elucidated that ZrP displays different sorption affinity towards heavy metals in the same order as selectivity sequence of Pb(2+)>Zn(2+) approximately Cd(2+)>Ca(2+), which can be explained by hard and soft acids and bases (HASB) theory. Moreover, uptake of heavy metals onto ZrP approached to equilibrium quickly and the used ZrP could be readily regenerated for reuse by the dilute HCl solution. Thus, all the results suggest that amorphous ZrP has excellent potential as a sorption material for water treatment.

Production of magnesium metal

Science.gov (United States)

Blencoe, James G [Harriman, TN; Anovitz, Lawrence M [Knoxville, TN; Palmer, Donald A [Oliver Springs, TN; Beard, James S [Martinsville, VA

2010-02-23

A process of producing magnesium metal includes providing magnesium carbonate, and reacting the magnesium carbonate to produce a magnesium-containing compound and carbon dioxide. The magnesium-containing compound is reacted to produce magnesium metal. The carbon dioxide is used as a reactant in a second process. In another embodiment of the process, a magnesium silicate is reacted with a caustic material to produce magnesium hydroxide. The magnesium hydroxide is reacted with a source of carbon dioxide to produce magnesium carbonate. The magnesium carbonate is reacted to produce a magnesium-containing compound and carbon dioxide. The magnesium-containing compound is reacted to produce magnesium metal. The invention further relates to a process for production of magnesium metal or a magnesium compound where an external source of carbon dioxide is not used in any of the reactions of the process. The invention also relates to the magnesium metal produced by the processes described herein.

Gas-phase fragmentation of coordination compounds: loss of CO(2) from inorganic carbonato complexes to give metal oxide ions

Science.gov (United States)

Dalgaard; McKenzie

1999-10-01

Using electrospray ionization mass spectrometry, novel transition metal oxide coordination complex ions are proposed as the products of the collision-induced dissociation (CID) of some carbonato complex ions through the loss of a mass equivalent to CO(2). CID spectra of [(tpa)CoCO(3)](+) (tpa = tris(2-pyridylmethyl)methylamine), [(bispicMe(2)en)Fe(&mgr;-O)(&mgr;-CO(3))Fe(bispicMe(2)en)]2+ (bispicMe(2)en = N,N'-dimethyl-N,N'-bis(2-pyridylmethy)eth- ane-1, 2-diamine) and [(bpbp)Cu(2)CO(3)](+) (bpbp(-) = bis[(bis-(2-pyridylmethyl)amino)methyl]-4-tertbutylpheno-lato(1-)), show peaks assigned to the mono- and dinuclear oxide cations, [(tpa)CoO](+), [(bispicMe(2)en)(2)Fe(2)(O)(2)]2+ and [(bpbp)Cu(2)O](+), as the dominant species. These results can be likened to the reverse of typical synthetic reactions in which metal hydroxide compounds react with CO(2) to give metal carbonato compounds. Because of the lack of available protons in the gas phase, novel oxide species rather than the more common hydroxide ions are generated. These oxide ions are relevant to the highly oxidizing species proposed in oxygenation reactions catalysed by metal oxides and metalloenzymes. Copyright 1999 John Wiley & Sons, Ltd.

Biosurfactant Mediated Biosynthesis of Selected Metallic Nanoparticles

Directory of Open Access Journals (Sweden)

Grażyna A. Płaza

2014-08-01

Full Text Available Developing a reliable experimental protocol for the synthesis of nanomaterials is one of the challenging topics in current nanotechnology particularly in the context of the recent drive to promote green technologies in their synthesis. The increasing need to develop clean, nontoxic and environmentally safe production processes for nanoparticles to reduce environmental impact, minimize waste and increase energy efficiency has become essential in this field. Consequently, recent studies on the use of microorganisms in the synthesis of selected nanoparticles are gaining increased interest as they represent an exciting area of research with considerable development potential. Microorganisms are known to be capable of synthesizing inorganic molecules that are deposited either intra- or extracellularly. This review presents a brief overview of current research on the use of biosurfactants in the biosynthesis of selected metallic nanoparticles and their potential importance.

Biosurfactant Mediated Biosynthesis of Selected Metallic Nanoparticles

Science.gov (United States)

Płaza, Grażyna A.; Chojniak, Joanna; Banat, Ibrahim M.

2014-01-01

Developing a reliable experimental protocol for the synthesis of nanomaterials is one of the challenging topics in current nanotechnology particularly in the context of the recent drive to promote green technologies in their synthesis. The increasing need to develop clean, nontoxic and environmentally safe production processes for nanoparticles to reduce environmental impact, minimize waste and increase energy efficiency has become essential in this field. Consequently, recent studies on the use of microorganisms in the synthesis of selected nanoparticles are gaining increased interest as they represent an exciting area of research with considerable development potential. Microorganisms are known to be capable of synthesizing inorganic molecules that are deposited either intra- or extracellularly. This review presents a brief overview of current research on the use of biosurfactants in the biosynthesis of selected metallic nanoparticles and their potential importance. PMID:25110864

Self-sorting of dynamic metallosupramolecular libraries (DMLs) via metal-driven selection.

Science.gov (United States)

Kocsis, Istvan; Dumitrescu, Dan; Legrand, Yves-Marie; van der Lee, Arie; Grosu, Ion; Barboiu, Mihail

2014-03-11

"Metal-driven" selection between finite mononuclear and polymeric metallosupramolecular species can be quantitatively achieved in solution and in a crystalline state via coupled coordination/stacking interactional algorithms within dynamic metallosupramolecular libraries - DMLs.

Asymmetric synthesis using chiral-encoded metal

Science.gov (United States)

Yutthalekha, Thittaya; Wattanakit, Chularat; Lapeyre, Veronique; Nokbin, Somkiat; Warakulwit, Chompunuch; Limtrakul, Jumras; Kuhn, Alexander

2016-08-01

The synthesis of chiral compounds is of crucial importance in many areas of society and science, including medicine, biology, chemistry, biotechnology and agriculture. Thus, there is a fundamental interest in developing new approaches for the selective production of enantiomers. Here we report the use of mesoporous metal structures with encoded geometric chiral information for inducing asymmetry in the electrochemical synthesis of mandelic acid as a model molecule. The chiral-encoded mesoporous metal, obtained by the electrochemical reduction of platinum salts in the presence of a liquid crystal phase and the chiral template molecule, perfectly retains the chiral information after removal of the template. Starting from a prochiral compound we demonstrate enantiomeric excess of the (R)-enantiomer when using (R)-imprinted electrodes and vice versa for the (S)-imprinted ones. Moreover, changing the amount of chiral cavities in the material allows tuning the enantioselectivity.

Hard X-ray PhotoElectron Spectroscopy of transition metal oxides: Bulk compounds and device-ready metal-oxide interfaces

International Nuclear Information System (INIS)

Borgatti, F.; Torelli, P.; Panaccione, G.

2016-01-01

Highlights: • Hard X-ray PhotoElectron Spectroscopy (HAXPES) applied to buried interfaces of systems involving Transition Metal Oxides. • Enhanced contribution of the s states at high kinetic energies both for valence and core level spectra. • Sensitivity to chemical changes promoted by electric field across metal-oxide interfaces in resistive switching devices. - Abstract: Photoelectron spectroscopy is one of the most powerful tool to unravel the electronic structure of strongly correlated materials also thanks to the extremely large dynamic range in energy, coupled to high energy resolution that this form of spectroscopy covers. The kinetic energy range typically used for photoelectron experiments corresponds often to a strong surface sensitivity, and this turns out to be a disadvantage for the study of transition metal oxides, systems where structural and electronic reconstruction, different oxidation state, and electronic correlation may significantly vary at the surface. We report here selected Hard X-ray PhotoElectron Spectroscopy (HAXPES) results from transition metal oxides, and from buried interfaces, where we highlight some of the important features that such bulk sensitive technique brings in the analysis of electronic properties of the solids.

Hard X-ray PhotoElectron Spectroscopy of transition metal oxides: Bulk compounds and device-ready metal-oxide interfaces

Energy Technology Data Exchange (ETDEWEB)

Borgatti, F., E-mail: francesco.borgatti@cnr.it [Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Consiglio Nazionale delle Ricerche (CNR), via P. Gobetti 101, Bologna I-40129 (Italy); Torelli, P.; Panaccione, G. [Istituto Officina dei Materiali (IOM)-CNR, Laboratorio TASC, Area Science Park, Trieste I-34149 (Italy)

2016-04-15

Highlights: • Hard X-ray PhotoElectron Spectroscopy (HAXPES) applied to buried interfaces of systems involving Transition Metal Oxides. • Enhanced contribution of the s states at high kinetic energies both for valence and core level spectra. • Sensitivity to chemical changes promoted by electric field across metal-oxide interfaces in resistive switching devices. - Abstract: Photoelectron spectroscopy is one of the most powerful tool to unravel the electronic structure of strongly correlated materials also thanks to the extremely large dynamic range in energy, coupled to high energy resolution that this form of spectroscopy covers. The kinetic energy range typically used for photoelectron experiments corresponds often to a strong surface sensitivity, and this turns out to be a disadvantage for the study of transition metal oxides, systems where structural and electronic reconstruction, different oxidation state, and electronic correlation may significantly vary at the surface. We report here selected Hard X-ray PhotoElectron Spectroscopy (HAXPES) results from transition metal oxides, and from buried interfaces, where we highlight some of the important features that such bulk sensitive technique brings in the analysis of electronic properties of the solids.

Possible explosive compounds in the Savannah River Site waste tank farm facilities

International Nuclear Information System (INIS)

Hobbs, D.T.

1992-01-01

Based on a comparison of the known constituents in high-level nuclear waste stored at the Savannah River Site (SRS) and explosive compounds reported in the literature, only two classes of explosive compounds (metal NO x compounds and organic compounds) were identified as requiring further work to determine if they exist in the waste, and if so, in what quantities. Of the fourteen classes of explosive compounds identified as conceivably being present in tank farm operations, nine classes (metal fulminates, metal azides, halogen compounds, metal-amine complexes, nitrate/oxalate mixtures, metal oxalates, metal oxohalogenates, metal cyanides/cyanates, and peroxides) are not a hazard because these classes of compounds cannot be formed or accumulated in sufficient quantity, or they are not reactive at the conditions which exist in the tank farm facilities. Three of the classes (flammable gases, metal nitrides, and ammonia compounds and derivatives) are known to have the potential to build up to concentrations at which an observable reaction might occur. Controls have been in place for some time to limit the formation or control the concentration of these classes of compounds. A comprehensive list of conceivable explosive compounds is provided in Appendix 3

Peracetic Acid Depolymerization of Biorefinery Lignin for Production of Selective Monomeric Phenolic Compounds

Energy Technology Data Exchange (ETDEWEB)

Ma, Ruoshui [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA; Guo, Mond [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA; Lin, Kuan-ting [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA; Hebert, Vincent R. [Food and Environmental Laboratory, Washington State, University-TriCities, 2710 Crimson Way Richland WA 99354 USA; Zhang, Jinwen [Wood Materials and Engineering Laboratory, Washington State University, Pullman WA 99164 USA; Wolcott, Michael P. [Wood Materials and Engineering Laboratory, Washington State University, Pullman WA 99164 USA; Quintero, Melissa [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA; Ramasamy, Karthikeyan K. [Chemical and Biological Process Development Group, Pacific Northwest National Laboratory, Richland WA 99354 USA; Chen, Xiaowen [National Bioenergy Center, National Renewable Energy Lab, 1617 Cole Blvd Golden CO 80127 USA; Zhang, Xiao [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA

2016-07-04

Lignin is the largest source of renewable material with an aromatic skeleton. However, due to the recalcitrant and heterogeneous nature of the lignin polymer, it has been a challenge to effectively depolymerize lignin and produce high-value chemicals with high selectivity. In this study, a highly efficient lignin-to-monomeric phenolic compounds (MPC) conversion method based on peracetic acid (PAA) treatment was reported. PAA treatment of two biorefinery lignin samples, diluted acid pretreated corn stover lignin (DACSL) and steam exploded spruce lignin (SESPL), led to complete solubilization and production of selective hydroxylated monomeric phenolic compounds (MPC-H) and monomeric phenolic acid compounds (MPC-A) including 4-hydroxy-2-methoxyphenol, p-hydroxybenzoic acid, vanillic acid, syringic acid, and 3,4-dihydroxybenzoic acid. The maximized MPC yields obtained were 18 and 22 % based on the initial weight of the lignin in SESPL and DACSL, respectively. However, we found that the addition of niobium pentoxide catalyst to PAA treatment of lignin can significantly improve the MPC yields up to 47 %. The key reaction steps and main mechanisms involved in this new lignin-to-MPC valorization pathway were investigated and elucidated.

Peracetic Acid Depolymerization of Biorefinery Lignin for Production of Selective Monomeric Phenolic Compounds

Energy Technology Data Exchange (ETDEWEB)

Ma, Ruoshui [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA; Guo, Mond [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA; Lin, Kuan-ting [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA; Hebert, Vincent R. [Food and Environmental Laboratory, Washington State, University-TriCities, 2710 Crimson Way Richland WA 99354 USA; Zhang, Jinwen [Wood Materials and Engineering Laboratory, Washington State University, Pullman WA 99164 USA; Wolcott, Michael P. [Wood Materials and Engineering Laboratory, Washington State University, Pullman WA 99164 USA; Quintero, Melissa [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA; Ramasamy, Karthikeyan K. [Chemical and Biological Process Development Group, Pacific Northwest National Laboratory, Richland WA 99354 USA; Chen, Xiaowen [National Bioenergy Center, National Renewable Energy Lab, 1617 Cole Blvd Golden CO 80127 USA; Zhang, Xiao [Voiland School of Chemical Engineering and Bioengineering, Bioproducts, Science & Engineering Laboratory, Washington State University, 2710 Crimson Way Richland WA 99354 USA

2016-07-04

Lignin is the largest source of renewable material with an aromatic skeleton. However, due to the recalcitrant and heterogeneous nature of the lignin polymer as well as its complex side chain structures, it has been a challenge to effectively depolymerize lignin and produce high value chemicals with high selectivity. In this study, a highly efficient lignin-to-monomeric phenolic compounds (MPC) conversion method based on peracetic acid (PAA) treatment was reported. PAA treatment of two biorefinery lignin samples, diluted acid pretreated corn stover lignin (DACSL) and steam exploded spruce lignin (SESPL), led to complete solubilization and production of selective hydroxylated monomeric phenolic compounds (MPC-H) and monomeric phenolic acid compounds (MPC-A) inclduing 4-hydroxy-2-methoxyphenol, p-hydroxybenzoic acid, vanillic acid, syringic acid, and 3,4-dihydroxybenzoic acid. The maximized MPCs yields obtained were 18% and 22% based on the initial weight of the lignin in SESPL and DACSL respectively. However, we found that the addition of niobium pentoxide catalyst to PAA treatment of lignin can significantly improve the MPC yields up to 47%. The key reaction steps and main mechanisms involved in this new lignin-to-MPC valorization pathway were investigated and elucidated.

Solar selective performance of metal nitride/oxynitride based magnetron sputtered thin film coatings: a comprehensive review

Science.gov (United States)

Ibrahim, Khalil; Taha, Hatem; Mahbubur Rahman, M.; Kabir, Humayun; Jiang, Zhong-Tao

2018-03-01

Since solar-thermal collectors are considered to be the most direct way of converting solar energy into usable forms, in the last few years growing attention has been paid to the development of transition metal nitride and metal oxynitride based thin film selective surfaces for solar-thermal collectors, in order to harvest more solar energy. A solar-thermal energy system, generally, shows very high solar absorption of incident solar radiation from the solar-thermal collectors in the visible range (0.3 to 2.5 μm) and extremely low thermal losses through emission (or high reflection) in the infrared region (≥2.5 μm). The efficiency of a solar-thermal energy conversion system can be improved by the use of solar selective surfaces consisting of novel metallic nanoparticles embedded in metal nitride/oxynitride systems. In order to enhance the effectiveness of solar-thermal devices, solar selective surfaces with high thermal stability are a prerequisite. Over the years, substantial efforts have been made in the field of solar selective surfaces to attain higher solar absorptance and lower thermal emittance in high temperature (above 400 °C) applications. In this article, we review the present state-of-the-art transition metal nitride and/or oxynitride based vacuum sputtered nanostructured thin film coatings, with respect to their optical and solar selective surface applications. We have also summarized the solar selectivity data from recently published investigations, including discussion on some potential applications for these materials.

Organic-Inorganic Hybrid Polymers as Adsorbents for Removal of Heavy Metal Ions from Solutions: A Review

Science.gov (United States)

Samiey, Babak; Cheng, Chil-Hung; Wu, Jiangning

2014-01-01

Over the past decades, organic-inorganic hybrid polymers have been applied in different fields, including the adsorption of pollutants from wastewater and solid-state separations. In this review, firstly, these compounds are classified. These compounds are prepared by sol-gel method, self-assembly process (mesopores), assembling of nanobuilding blocks (e.g., layered or core-shell compounds) and as interpenetrating networks and hierarchically structures. Lastly, the adsorption characteristics of heavy metals of these materials, including different kinds of functional groups, selectivity of them for heavy metals, effect of pH and synthesis conditions on adsorption capacity, are studied. PMID:28788483

Passive sampling of selected endocrine disrupting compounds using polar organic chemical integrative samplers

International Nuclear Information System (INIS)

Arditsoglou, Anastasia; Voutsa, Dimitra

2008-01-01

Two types of polar organic chemical integrative samplers (pharmaceutical POCIS and pesticide POCIS) were examined for their sampling efficiency of selected endocrine disrupting compounds (EDCs). Laboratory-based calibration of POCISs was conducted by exposing them at high and low concentrations of 14 EDCs (4-alkyl-phenols, their ethoxylate oligomers, bisphenol A, selected estrogens and synthetic steroids) for different time periods. The kinetic studies showed an integrative uptake up to 28 days. The sampling rates for the individual compounds were obtained. The use of POCISs could result in an integrative approach to the quality status of the aquatic systems especially in the case of high variation of water concentrations of EDCs. The sampling efficiency of POCISs under various field conditions was assessed after their deployment in different aquatic environments. - Calibration and field performance of polar organic integrative samplers for monitoring EDCs in aquatic environments

Charge transfer in gold--alkali-metal systems

International Nuclear Information System (INIS)

Watson, R.E.; Weinert, M.

1994-01-01

Based on conventional electronegativity arguments, gold--alkali-metal compounds are expected to be among the most ''ionic'' of metallic compounds. The concepts of ionicity and charge transfer are difficult to quantify. However, the changes in bonding in the 50/50 Au--alkali-metal systems between the elemental metals and the compounds are so severe that observations can readily be made concerning their character. The results, as obtained from self-consistent electronic-structure calculations, lead to the apparently odd observation that the electron density at the alkali-metal sites in the compound increases significantly and this involves high l componennts in the charge density. This increase, however, can be attributed to Au-like orbitals spatially overlapping the alkali-metal sites. In a chemical sense, it is reasonable to consider the alkali-metal transferring charge to these Au orbitals. While normally the difference in heats of formation between muffin-tin and full-potential calculations for transition-metal--transition-metal and transition-metal--main-group (e.g., Al) compounds having high site symmetry are small, for the gold--alkali-metal systems, the changes in bonding in the compounds cause differences of ∼0.5 eV/atom between the two classes of potential. Any serious estimate of the electronic structure in these systems must account for these aspherical bonding charges. The origin of the semiconducting behavior of the heavy-alkali-metal Au compounds is shown to arise from a combination of the Au-Au separations and the ionic character of the compounds; the light-alkali-metal Au compounds, with their smaller Au-Au separations, do not have a semiconducting gap. Core-level shifts and isomer shifts are also briefly discussed

Process for cleaning radioactively contaminated metal surfaces

International Nuclear Information System (INIS)

Mihram, R.G.; Snyder, G.A.

1975-01-01

A process is described for removing radioactive scale from a ferrous metal surface, including the steps of initially preconditioning the surface by contacting it with an oxidizing solution (such as an aqueous solution of an alkali metal permanganate or hydrogen peroxide), then, after removal or decomposition of the oxidizing solution, the metallic surface is contacted with a cleaning solution which is a mixture of a mineral acid and a complexing agent (such as sulfuric acid and oxalic acid), and which preferably contains a corrosion inhibitor. A final step in the process is the treatment of the spent cleaning solution containing radioactive waste materials in solution by adding a reagent selected from the group consisting of calcium hydroxide or potassium permanganate and an alkali metal hydroxide to thereby form easily recovered metallic compounds containing substantially all of the dissolved metals and radioactivity. (auth)

High-throughput screening of metal-porphyrin-like graphenes for selective capture of carbon dioxide.

Science.gov (United States)

Bae, Hyeonhu; Park, Minwoo; Jang, Byungryul; Kang, Yura; Park, Jinwoo; Lee, Hosik; Chung, Haegeun; Chung, ChiHye; Hong, Suklyun; Kwon, Yongkyung; Yakobson, Boris I; Lee, Hoonkyung

2016-02-23

Nanostructured materials, such as zeolites and metal-organic frameworks, have been considered to capture CO2. However, their application has been limited largely because they exhibit poor selectivity for flue gases and low capture capacity under low pressures. We perform a high-throughput screening for selective CO2 capture from flue gases by using first principles thermodynamics. We find that elements with empty d orbitals selectively attract CO2 from gaseous mixtures under low CO2 pressures (~10(-3) bar) at 300 K and release it at ~450 K. CO2 binding to elements involves hybridization of the metal d orbitals with the CO2 π orbitals and CO2-transition metal complexes were observed in experiments. This result allows us to perform high-throughput screening to discover novel promising CO2 capture materials with empty d orbitals (e.g., Sc- or V-porphyrin-like graphene) and predict their capture performance under various conditions. Moreover, these findings provide physical insights into selective CO2 capture and open a new path to explore CO2 capture materials.

High-throughput screening of metal-porphyrin-like graphenes for selective capture of carbon dioxide

Science.gov (United States)

Bae, Hyeonhu; Park, Minwoo; Jang, Byungryul; Kang, Yura; Park, Jinwoo; Lee, Hosik; Chung, Haegeun; Chung, Chihye; Hong, Suklyun; Kwon, Yongkyung; Yakobson, Boris I.; Lee, Hoonkyung

2016-02-01

Nanostructured materials, such as zeolites and metal-organic frameworks, have been considered to capture CO2. However, their application has been limited largely because they exhibit poor selectivity for flue gases and low capture capacity under low pressures. We perform a high-throughput screening for selective CO2 capture from flue gases by using first principles thermodynamics. We find that elements with empty d orbitals selectively attract CO2 from gaseous mixtures under low CO2 pressures (~10-3 bar) at 300 K and release it at ~450 K. CO2 binding to elements involves hybridization of the metal d orbitals with the CO2 π orbitals and CO2-transition metal complexes were observed in experiments. This result allows us to perform high-throughput screening to discover novel promising CO2 capture materials with empty d orbitals (e.g., Sc- or V-porphyrin-like graphene) and predict their capture performance under various conditions. Moreover, these findings provide physical insights into selective CO2 capture and open a new path to explore CO2 capture materials.

Effect of photo-selective nettings on post-harvest quality and bioactive compounds in selected tomato cultivars.

Science.gov (United States)

Selahle, Maphoko Kamogelo; Sivakumar, Dharini; Soundy, Puffy

2014-08-01

Photo-selective coloured netting is referred to as a 'new agro-technological' concept adopted to manipulate light quality changes that can induce favourable responses in plants. Tomato (Solanum lycopersicum L.) cultivars AlvaV, Irit and SCX 248 grown under the black net (commercial net, 25% shading) showed higher weight loss, loss of firmness, ascorbic acid content and decline in the ratio of soluble solids content/titrable acidity during post-harvest storage (low-temperature storage at 10°C and 90% relative humidity for 21 days followed by market shelf conditions at 25°C for 2 days). During post-harvest storage, lycopene, β-carotene, total phenolic content and antioxidant scavenging activity were higher in cvs AlfaV and Irit grown under the black or pearl nets. However, the β-carotene, total phenolic content and antioxidant scavenging activity were higher in SCX 248 grown under the red net during post-harvest storage. Cultivar AlfaV grown under the red and pearl nets had a higher number of odour active aroma compounds during post-harvest storage. Panellists preferred cv. AlfaV grown under the pearl nets after storage based on taste, overall appearance and firm textured fruits. Pearl photo-selective nets retained the overall fruit quality and bioactive components in cvs AlfaV and Irit during post-harvest storage. Red photo-selective nets, however, showed greater influence on retention of overall fruit quality and bioactive compounds in cv. SCX 248 during post-harvest storage. © 2013 Society of Chemical Industry.

Enthalpies of formation of selected Co{sub 2}YZ Heusler compounds

Energy Technology Data Exchange (ETDEWEB)

Yin, Ming, E-mail: myin1@hawk.iit.edu; Chen, Song; Nash, Philip

2013-11-15

Highlights: •Enthalpies of formation of selected Co{sub 2}YZ were measured by drop calorimeters. •Enthalpy decreases as the Z element approaches the top right corner of the periodic table. •For the Y element, enthalpy increases on increasing the number of d electrons. •Result of L2{sub 1} structured compounds agrees with first principles data. •Lattice parameters and related phase relationships were consistent with literature data. -- Abstract: Standard enthalpies of formation at 298 K of selected ternary Co{sub 2}-based Heusler compounds Co{sub 2}YZ (Y = Fe, Hf, Mn, Ti, V, Zr; Z = Al, Ga, In, Si, Ge, Sn) were measured by high temperature direct synthesis calorimetry. The measured enthalpies of formation (in kJ/mole of atoms) of the L2{sub 1} compounds are: Co{sub 2}FeGa (−25.8 ± 2.6); Co{sub 2}FeSi (−38.4 ± 2.2); Co{sub 2}FeGe (−11.6 ± 2.1); Co{sub 2}MnGa (−30.1 ± 2.3); Co{sub 2}MnSi (−42.4 ± 1.2); Co{sub 2}MnGe (−31.6 ± 3.0); Co{sub 2}MnSn (−15.6 ± 2.8); Co{sub 2}TiAl (−55.0 ± 3.7); Co{sub 2}TiGa (−54.2 ± 2.6); Co{sub 2}TiSi (−61.4 ± 1.7); Co{sub 2}TiGe (−59.3 ± 3.8); Co{sub 2}TiSn (−38.4 ± 2.0); Co{sub 2}VGa (−28.4 ± 1.1) and for the B2 compounds: Co{sub 2}FeAl (−22.5 ± 2.5), Co{sub 2}MnAl (−27.6 ± 2.7). Values are compared with those from first principles calculation when available and the extended semi-empirical model of Miedema. Trends in enthalpy of formation with element atomic number are discussed. Lattice parameters of the compounds with L2{sub 1} structure are determined by X-ray diffraction analysis.

Selective synthesis and characterization of sea urchin-like metallic nickel nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Liu Xiaohe [Department of Inorganic Materials, Central South University, Changsha, Hunan 410083 (China)]. E-mail: liuxh@mail.csu.edu.cn; Liang Xudong [Department of Inorganic Materials, Central South University, Changsha, Hunan 410083 (China); Zhang Ning [Department of Inorganic Materials, Central South University, Changsha, Hunan 410083 (China); Qiu Guanzhou [Department of Inorganic Materials, Central South University, Changsha, Hunan 410083 (China); Yi Ran [Department of Inorganic Materials, Central South University, Changsha, Hunan 410083 (China)

2006-08-15

Sea urchin-like nanobelt-based and nanorod-based metallic nickel nanocrystals have been selective synthesized via a hydrothermal reduction route in which sodium hydroxide was used as alkaline reagent and aqueous hydrazine (N{sub 2}H{sub 4}.H{sub 2}O) was used as reducing agent. The morphology and structure of final products could be easily controlled by adjust process parameters such as hydrothermal time, reaction temperature and alkaline concentration. Surfactant cetyltrimethylammonium bromide (CTAB) was also important parameter influencing the morphology of the products. The morphology and phase structure of the final products have been investigated by X-ray diffraction, transmission electron microscopy and selected area electron diffraction. The probable formation mechanism of the sea urchin-like metallic nickel nanocrystals was discussed on the basis of the experimental results.

Phyto-metals screening of selected anti-diabetic herbs and infused concoctions

OpenAIRE

Olanrewaju O. Olujimi; Olusegun N. Onifade; Adeleke T. Towolawi; Temilade F. Akinhanmi; Adeniyi A. Afolabi; Kabir A. Olanite

2017-01-01

Objective: To determine the levels of some selected heavy metals in both the selected anti-diabetic herbal plants and infused concoctions for diabetes treatment. Methods: Ten anti-diabetic plant samples: pawpaw leaves (Carica papaya), bitter melon leaves (Momordica charantia), holy basil leaves (Ocimum sanctum), bitter leaf (Vernonia amygdalina), ginger rhizome (Zingiber officinale), garlic (Allium sativum), African red pepper fruits (Capsicum frutescens), negro pepper grain (Xylopia aethi...

Investigations on organogermanium compounds XII. Reactions of trialkylgermylalkalimetal compounds in hexamethylphosphoric triamide (HMPT) with some inorganic and organic compounds

NARCIS (Netherlands)

Bulten, E.J.; Noltes, J.G.

1971-01-01

Trialkylgermyl alkali metal compounds in HMPT have been found to be highly reactive nucleophiles. Reactions with some inorganic and organic compounds, such as oxygen, carbon dioxide, inorganic and orgaanic halides, aldehydes, ketones, epoxides and lactones are described. Several new

Serum heavy metals and hemoglobin related compounds in Saudi Arabia firefighters

Directory of Open Access Journals (Sweden)

Al-Malki Abdulrahman L

2009-07-01

Full Text Available Abstract Background Firefighters are frequently exposed to significant concentrations of hazardous materials including heavy metals, aldehydes, hydrogen chloride, dichlorofluoromethane and some particulates. Many of these materials have been implicated in the triggering of several diseases. The aim of the present study is to investigate the effect of fire smoke exposure on serum heavy metals and possible affection on iron functions compounds (total iron binding capacity, transferrin saturation percent, ferritin, unsaturated iron-binding capacity blood hemoglobin and carboxyhemoglobin,. Subjects and methods Two groups of male firefighter volunteers were included; the first included 28 firefighters from Jeddah city, while the second included 21 firefighters from Yanbu city with an overall age rang of 20–48 years. An additional group of 23 male non-firefighters volunteered from both cities as normal control subjects. Blood samples were collected from all volunteer subjects and investigated for relevant parameters. Results The results obtained showed that there were no statistically significant changes in the levels of serum heavy metals in firefighters as compared to normal control subjects. Blood carboxyhemoglobin and serum ferritin were statistically increased in Jeddah firefighters, (p Conclusion Such results might point to the need for more health protective and prophylactic measures to avoid such hazardous health effects (elevated Blood carboxyhemoglobin and serum ferritin and decreased serum TIBC and UIBC that might endanger firefighters working under dangerous conditions. Firefighters must be under regular medical follow-up through standard timetabled medical laboratory investigations to allow for early detection of any serum biochemical or blood hematological changes.

Recent Progress in Graphite Intercalation Compounds for Rechargeable Metal (Li, Na, K, Al)-Ion Batteries.

Science.gov (United States)

Xu, Jiantie; Dou, Yuhai; Wei, Zengxi; Ma, Jianmin; Deng, Yonghong; Li, Yutao; Liu, Huakun; Dou, Shixue

2017-10-01

Lithium-ion batteries (LIBs) with higher energy density are very necessary to meet the increasing demand for devices with better performance. With the commercial success of lithiated graphite, other graphite intercalation compounds (GICs) have also been intensively reported, not only for LIBs, but also for other metal (Na, K, Al) ion batteries. In this Progress Report, we briefly review the application of GICs as anodes and cathodes in metal (Li, Na, K, Al) ion batteries. After a brief introduction on the development history of GICs, the electrochemistry of cationic GICs and anionic GICs is summarized. We further briefly summarize the use of cationic GICs and anionic GICs in alkali ion batteries and the use of anionic GICs in aluminium-ion batteries. Finally, we reach some conclusions on the drawbacks, major progress, emerging challenges, and some perspectives on the development of GICs for metal (Li, Na, K, Al) ion batteries. Further development of GICs for metal (Li, Na, K, Al) ion batteries is not only a strong supplement to the commercialized success of lithiated-graphite for LIBs, but also an effective strategy to develop diverse high-energy batteries for stationary energy storage in the future.

Composite materials obtained by the ion-plasma sputtering of metal compound coatings on polymer films

Science.gov (United States)

Khlebnikov, Nikolai; Polyakov, Evgenii; Borisov, Sergei; Barashev, Nikolai; Biramov, Emir; Maltceva, Anastasia; Vereshchagin, Artem; Khartov, Stas; Voronin, Anton

2016-01-01

In this article, the principle and examples composite materials obtained by deposition of metal compound coatings on polymer film substrates by the ion-plasma sputtering method are presented. A synergistic effect is to obtain the materials with structural properties of the polymer substrate and the surface properties of the metal deposited coatings. The technology of sputtering of TiN coatings of various thicknesses on polyethylene terephthalate films is discussed. The obtained composites are characterized by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), atomic force microscopy (AFM), and scanning tunneling microscopy (STM) is shown. The examples of application of this method, such as receiving nanocomposite track membranes and flexible transparent electrodes, are considered.

Remediation of metal-contaminated urban soil using flotation technique

International Nuclear Information System (INIS)

Dermont, G.; Bergeron, M.; Richer-Lafleche, M.; Mercier, G.

2010-01-01

A soil washing process using froth flotation technique was evaluated for the removal of arsenic, cadmium, copper, lead, and zinc from a highly contaminated urban soil (brownfield) after crushing of the particle-size fractions > 250 μm. The metal contaminants were in particulate forms and distributed in all the particle-size fractions. The particle-by-particle study with SEM-EDS showed that Zn was mainly present as sphalerite (ZnS), whereas Cu and Pb were mainly speciated as various oxide/carbonate compounds. The influence of surfactant collector type (non-ionic and anionic), collector dosage, pulp pH, a chemical activation step (sulfidization), particle size, and process time on metal removal efficiency and flotation selectivity was studied. Satisfactory results in metal recovery (42-52%), flotation selectivity (concentration factor > 2.5), and volume reduction (> 80%) were obtained with anionic collector (potassium amyl xanthate). The transportation mechanisms involved in the separation process (i.e., the true flotation and the mechanical entrainment) were evaluated by the pulp chemistry, the metal speciation, the metal distribution in the particle-size fractions, and the separation selectivity indices of Zn/Ca and Zn/Fe. The investigations showed that a great proportion of metal-containing particles were recovered in the froth layer by entrainment mechanism rather than by true flotation process. The non-selective entrainment mechanism of the fine particles ( 5 min) and when a high collector dose is used. The intermediate particle-size fraction (20-125 μm) showed the best flotation selectivity.

Polystyrene Sulfonate Threaded through a Metal-Organic Framework Membrane for Fast and Selective Lithium-Ion Separation.

Science.gov (United States)

Guo, Yi; Ying, Yulong; Mao, Yiyin; Peng, Xinsheng; Chen, Banglin

2016-11-21

Extraction of lithium ions from salt-lake brines is very important to produce lithium compounds. Herein, we report a new approach to construct polystyrene sulfonate (PSS) threaded HKUST-1 metal-organic framework (MOF) membranes through an in situ confinement conversion process. The resulting membrane PSS@HKUST-1-6.7, with unique anchored three-dimensional sulfonate networks, shows a very high Li + conductivity of 5.53×10 -4  S cm -1 at 25 °C, 1.89×10 -3  S cm -1 at 70 °C, and Li + flux of 6.75 mol m -2  h -1 , which are five orders higher than that of the pristine HKUST-1 membrane. Attributed to the different size sieving effects and the affinity differences of the Li + , Na + , K + , and Mg 2+ ions to the sulfonate groups, the PSS@HKUST-1-6.7 membrane exhibits ideal selectivities of 78, 99, and 10296 for Li + /Na + , Li + /K + , Li + /Mg 2+ and real binary ion selectivities of 35, 67, and 1815, respectively, the highest ever reported among ionic conductors and Li + extraction membranes. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Metal interactions with boron clusters

International Nuclear Information System (INIS)

Grimes, R.N.

1982-01-01

This book presents information on the following topics: the structural and bonding features of metallaboranes and metallacarboranes; transition-metal derivatives of nido-boranes and some related species; interactions of metal groups with the octahydrotriborate (1-) anion, B 3 H 8 ; metallaboron cage compounds of the main group metals; closo-carborane-metal complexes containing metal-carbon and metal-boron omega-bonds; electrochemistry of metallaboron cage compounds; and boron clusters with transition metal-hydrogen bonds

Gases and carbon in metals

International Nuclear Information System (INIS)

Jehn, H.; Fromm, E.; Hoerz, G.

1978-01-01

This issue is part of a series of data on 'gases and carbon in metals'. The present survey includes results from papers dealing with gases and carbon in actinides and recommends critically selected data for each element. Firstly data od binary systems are presented, starting with hydrogen and followed by carbon, nitrogen, oxygen, and rare gases. Within one metal-metalloid system the data are listed under topics such as solubility limit, dissociation pressure of compunds, vapour pressure of volatile oxides, thermodynamic data, diffusion, transport parameters (effective valence, heat of transport), permeation of gases through metals, gas adsorption and gas desorption kinetics, compound formation, precipitation kinetics, and property changes. Following the data on binary systems, the data of ternary systems are presented, beginning with systems which contain one metal and two gases or one gas and carbon and continuing with systems with two metals and one gas or carbon. Within a ternary system the topics are arranged in the same way as in binary systems. (HB) [de

Trends in the Hydrodeoxygenation Activity and Selectivity of Transition Metal Surfaces

DEFF Research Database (Denmark)

Lausche, Adam C.; Falsig, Hanne; Jensen, Anker Degn

2014-01-01

This paper reports the use of a combination of density functional theory and microkinetic modelling to establish trends in the hydrodeoxygenation rates and selectivites of transition metal surfaces. Biomass and biomass-derived chemicals often contain large fractions of oxygenates. Removal...... of the oxygen through hydrotreating represents one strategy for producing commodity chemicals from these renewable materials. Using the model developed in this paper, we predict ethylene glycol hydrodeoxygenation selectivities for transition metals that are consistent with those reported in the literature...

Rare earth intermetallic compounds produced by a reduction-diffusion process

International Nuclear Information System (INIS)

Cech, R.E.

1975-01-01

A reduction-diffusion process is given for producing novel rare earth intermetallic compounds, such as cobalt--rare earth intermetallic compounds, especially compounds useful in preparing permanent magnets. A particulate mixture of rare earth metal halide, cobalt and calcium hydride is heated to effect reduction of the rare earth metal halide and to diffuse the resulting rare earth metal into the cobalt to form the intermetallic compound

Structural biology of the sequestration and transport of heavy metal toxins: NMR structure determination of proteins containing the -Cys-X-Y-Cys-metal binding motifs. 1997 annual progress report

International Nuclear Information System (INIS)

Opella, S.J.

1997-01-01

'There are enormous amounts of heavy metals in the environment, much of it in the form of organometallic compounds resulting from various types of industrial and military waste. Nearly all of these metals and compounds are highly toxic to biological organisms including humans. However, some bacteria thrive in the presence of high concentrations of heavy metal toxins because they possess efficient mechanisms for the detoxification of these metals and compounds. Heavy metals appear to be universally toxic because of their non-selective chemistry, for example Hg(II) reacts with essentially all exposed sulfhydryl groups on proteins, thus, it may seem surprising that any organism at all can survive these chemical insults much less those that grow in a toxic milieu. However, the prebiotic environment was undoubtedly heavily polluted with heavy metals from geological processes, and the most primitive organisms simply had to evolve mechanisms for dealing with them if they were going to be able to utilize Cys, His, and the other amino acids that contribute to metal binding sites in their proteins. Genes associated with bacterial resistance to Ag, AsO 2 , AsO 4 , Bi, Cd, Co, CrO 4 , Cu, Hg, iNi, TeO 3 , TI, Pb, Zn, and other metals of environmental concern have been described (Silver, 1992; Silver and Walderhaug, 1995).'

Magnetism in ordered metallic perovskite compound GdPd{sub 3}B{sub x}C{sub 1-x}

Energy Technology Data Exchange (ETDEWEB)

Pandey, Abhishek [S.N. Bose National Centre for Basic Sciences, Block-JD, Sector-III, Salt Lake, Kolkata 700098 (India); Experimental Condensed Matter Physics Division, Saha Institute of Nuclear Physics, 1/AF, Bidhannagar, Kolkata 700064 (India)], E-mail: abhishek.phy@gmail.com; Mazumdar, Chandan [Experimental Condensed Matter Physics Division, Saha Institute of Nuclear Physics, 1/AF, Bidhannagar, Kolkata 700064 (India)], E-mail: chandan.mazumdar@saha.ac.in; Ranganathan, R. [Experimental Condensed Matter Physics Division, Saha Institute of Nuclear Physics, 1/AF, Bidhannagar, Kolkata 700064 (India); Dattagupta, S. [Indian Institute of Science Education and Research, Block-HC, Sector-III, Salt Lake, Kolkata 700106 (India)

2009-08-15

We report results of dc-magnetization, ac-susceptibility and magnetoresistance measurements on crystalline metallic-perovskite compounds GdPd{sub 3}B{sub x}C{sub 1-x} (x=0.25, 0.50, 0.75 and 1.00) and the parent cubic compound GdPd{sub 3}. The interest in these materials stems from the observation of negative temperature coefficient of resistance and negative thermal expansion in some of the members of this series. In the present study, we show that by substitution of non-magnetic elements, boron and carbon, the nature of the magnetic interaction can be varied from dominating ferromagnetic to antiferromagnetic and finally to a canted magnetic structure without altering the crystal symmetry of the compounds. The variation of magnetic interaction by modifying the lattice parameter resembles Ruderman-Kittel-Kasuya-Yosida (RKKY) oscillations.

Selective recognition by novel calix system: ICT based chemosensor for metal ions

Energy Technology Data Exchange (ETDEWEB)

Bhatt, Keyur D.; Makwana, Bharat A.; Vyas, Disha J.; Mishra, Divya R.; Jain, Vinod K., E-mail: drvkjain@hotmail.com

2014-02-15

A new calix[4]pyrrole derivative bearing four dansyl groups through hydroxyl groups has been synthesized and duly characterized by FT-IR, NMR and ESI-MS. Tetra dansylated calix[4]pyrrole (TDCP) shows selective behavior for U(VI), Th(IV) and Fe(III) ions among all other metal ions, e.g. Li(I), Na(I), K(I), Ca(II), Ni(II), Cd(II), Cu(II), Zn(II), Pb(II), Hg(II) and Ag(I), in the absorption spectra as well as in the emission spectra. The absorption spectra show a bathochromic shift while the emission spectra along with red-shift exhibit quenching for U(VI), Th(IV) and Fe(III) ions. The binding constants, stoichiometry and quantum yields have been determined. The mechanism of quenching by Stern–Vohmer equation has also been discussed. -- highlights: • A new selective turn-off fluorescent sensor i.e. tetra dansylated calix[4]pyrrole (TDCP) was synthesized and characterized. • The sensor shows selective behavior for U(VI), Th(IV) and Fe(III) ions among various other metal ions. • The absorption spectra show a bathochromic shift while the emission spectra along with red-shift exhibit quenching for U(VI), Th(IV) and Fe(III) ions. • The sensor binds metal ions in 1:1 stoichiometry with good binding constant.

Selective recognition by novel calix system: ICT based chemosensor for metal ions

International Nuclear Information System (INIS)

Bhatt, Keyur D.; Makwana, Bharat A.; Vyas, Disha J.; Mishra, Divya R.; Jain, Vinod K.

2014-01-01

A new calix[4]pyrrole derivative bearing four dansyl groups through hydroxyl groups has been synthesized and duly characterized by FT-IR, NMR and ESI-MS. Tetra dansylated calix[4]pyrrole (TDCP) shows selective behavior for U(VI), Th(IV) and Fe(III) ions among all other metal ions, e.g. Li(I), Na(I), K(I), Ca(II), Ni(II), Cd(II), Cu(II), Zn(II), Pb(II), Hg(II) and Ag(I), in the absorption spectra as well as in the emission spectra. The absorption spectra show a bathochromic shift while the emission spectra along with red-shift exhibit quenching for U(VI), Th(IV) and Fe(III) ions. The binding constants, stoichiometry and quantum yields have been determined. The mechanism of quenching by Stern–Vohmer equation has also been discussed. -- highlights: • A new selective turn-off fluorescent sensor i.e. tetra dansylated calix[4]pyrrole (TDCP) was synthesized and characterized. • The sensor shows selective behavior for U(VI), Th(IV) and Fe(III) ions among various other metal ions. • The absorption spectra show a bathochromic shift while the emission spectra along with red-shift exhibit quenching for U(VI), Th(IV) and Fe(III) ions. • The sensor binds metal ions in 1:1 stoichiometry with good binding constant

Remediation of metal-contaminated urban soil using flotation technique

Energy Technology Data Exchange (ETDEWEB)

Dermont, G., E-mail: dermonge@gmail.com [Institut National de la Recherche Scientifique Eau Terre et Environnement (INRS-ETE), 490, rue de la Couronne, Quebec, QC, Canada G1K 9A9 (Canada); Bergeron, M.; Richer-Lafleche, M.; Mercier, G. [Institut National de la Recherche Scientifique Eau Terre et Environnement (INRS-ETE), 490, rue de la Couronne, Quebec, QC, Canada G1K 9A9 (Canada)

2010-02-01

A soil washing process using froth flotation technique was evaluated for the removal of arsenic, cadmium, copper, lead, and zinc from a highly contaminated urban soil (brownfield) after crushing of the particle-size fractions > 250 {mu}m. The metal contaminants were in particulate forms and distributed in all the particle-size fractions. The particle-by-particle study with SEM-EDS showed that Zn was mainly present as sphalerite (ZnS), whereas Cu and Pb were mainly speciated as various oxide/carbonate compounds. The influence of surfactant collector type (non-ionic and anionic), collector dosage, pulp pH, a chemical activation step (sulfidization), particle size, and process time on metal removal efficiency and flotation selectivity was studied. Satisfactory results in metal recovery (42-52%), flotation selectivity (concentration factor > 2.5), and volume reduction (> 80%) were obtained with anionic collector (potassium amyl xanthate). The transportation mechanisms involved in the separation process (i.e., the true flotation and the mechanical entrainment) were evaluated by the pulp chemistry, the metal speciation, the metal distribution in the particle-size fractions, and the separation selectivity indices of Zn/Ca and Zn/Fe. The investigations showed that a great proportion of metal-containing particles were recovered in the froth layer by entrainment mechanism rather than by true flotation process. The non-selective entrainment mechanism of the fine particles (< 20 {mu}m) caused a flotation selectivity drop, especially with a long flotation time (> 5 min) and when a high collector dose is used. The intermediate particle-size fraction (20-125 {mu}m) showed the best flotation selectivity.

Remediation of metal-contaminated urban soil using flotation technique.

Science.gov (United States)

Dermont, G; Bergeron, M; Richer-Laflèche, M; Mercier, G

2010-02-01

A soil washing process using froth flotation technique was evaluated for the removal of arsenic, cadmium, copper, lead, and zinc from a highly contaminated urban soil (brownfield) after crushing of the particle-size fractions >250microm. The metal contaminants were in particulate forms and distributed in all the particle-size fractions. The particle-by-particle study with SEM-EDS showed that Zn was mainly present as sphalerite (ZnS), whereas Cu and Pb were mainly speciated as various oxide/carbonate compounds. The influence of surfactant collector type (non-ionic and anionic), collector dosage, pulp pH, a chemical activation step (sulfidization), particle size, and process time on metal removal efficiency and flotation selectivity was studied. Satisfactory results in metal recovery (42-52%), flotation selectivity (concentration factor>2.5), and volume reduction (>80%) were obtained with anionic collector (potassium amyl xanthate). The transportation mechanisms involved in the separation process (i.e., the true flotation and the mechanical entrainment) were evaluated by the pulp chemistry, the metal speciation, the metal distribution in the particle-size fractions, and the separation selectivity indices of Zn/Ca and Zn/Fe. The investigations showed that a great proportion of metal-containing particles were recovered in the froth layer by entrainment mechanism rather than by true flotation process. The non-selective entrainment mechanism of the fine particles (flotation selectivity drop, especially with a long flotation time (>5 min) and when a high collector dose is used. The intermediate particle-size fraction (20-125 microm) showed the best flotation selectivity. Copyright 2009 Elsevier B.V. All rights reserved.

Ammonia and hydrazine. Transition-metal-catalyzed hydroamination and metal-free catalyzed functionalization

Energy Technology Data Exchange (ETDEWEB)

Bertrand, Guy [Univ. of California, San Diego, CA (United States)

2012-06-29

The efficient and selective preparation of organic molecules is critical for mankind. For the future, it is of paramount importance to find catalysts able to transform abundant and cheap feedstocks into useful compounds. Acyclic and heterocyclic nitrogen-containing derivatives are common components of naturally occurring compounds, agrochemicals, cosmetics, and pharmaceuticals; they are also useful intermediates in a number of industrial processes. One of the most widely used synthetic strategies, allowing the formation of an N-C bond, is the addition of an N-H bond across a carbon-carbon multiple bond, the so-called hydroamination reaction. This chemical transformation fulfills the principle of “green chemistry” since it ideally occurs with 100% atom economy. Various catalysts have been found to promote this reaction, although many limitations remain; one of the most prominent is the lack of methods that permit the use of NH₃ and NH₂NH₂ as the amine partners. In fact, ammonia and hydrazine have rarely succumbed to homogeneous catalytic transformations. Considering the low cost and abundance of ammonia (136 million metric tons produced in 2011) and hydrazine, catalysts able to improve the reactivity and selectivity of the NH₃- and NH₂NH₂-hydroamination reaction, and more broadly speaking the functionalization of these chemicals, are highly desirable. In the last funded period, we discovered the first homogeneous catalysts able to promote the hydroamination of alkynes and allenes with ammonia and the parent hydrazine. The key feature of our catalytic systems is that the formation of catalytically inactive Werner complexes is reversible, in marked contrast to most of the known ammonia and hydrazine transition metal complexes. This is due to the peculiar electronic properties of our neutral ancillary ligands, especially their strong donating capabilities. However, our catalysts currently require

Morphological effects on the selectivity of intramolecular versus intermolecular catalytic reaction on Au nanoparticles.

Science.gov (United States)

Wang, Dan; Sun, Yuanmiao; Sun, Yinghui; Huang, Jing; Liang, Zhiqiang; Li, Shuzhou; Jiang, Lin

2017-06-14

It is hard for metal nanoparticle catalysts to control the selectivity of a catalytic reaction in a simple process. In this work, we obtain active Au nanoparticle catalysts with high selectivity for the hydrogenation reaction of aromatic nitro compounds, by simply employing spine-like Au nanoparticles. The density functional theory (DFT) calculations further elucidate that the morphological effect on thermal selectivity control is an internal key parameter to modulate the nitro hydrogenation process on the surface of Au spines. These results show that controlled morphological effects may play an important role in catalysis reactions of noble metal NPs with high selectivity.

Method and apparatus for dissociating metals from metal compounds extracted into supercritical fluids

Science.gov (United States)

Wai, Chien M.; Hunt, Fred H.; Smart, Neil G.; Lin, Yuehe

2000-01-01

A method for dissociating metal-ligand complexes in a supercritical fluid by treating the metal-ligand complex with heat and/or reducing or oxidizing agents is described. Once the metal-ligand complex is dissociated, the resulting metal and/or metal oxide form fine particles of substantially uniform size. In preferred embodiments, the solvent is supercritical carbon dioxide and the ligand is a .beta.-diketone such as hexafluoroacetylacetone or dibutyldiacetate. In other preferred embodiments, the metals in the metal-ligand complex are copper, silver, gold, tungsten, titanium, tantalum, tin, or mixtures thereof. In preferred embodiments, the reducing agent is hydrogen. The method provides an efficient process for dissociating metal-ligand complexes and produces easily-collected metal particles free from hydrocarbon solvent impurities. The ligand and the supercritical fluid can be regenerated to provide an economic, efficient process.

Intercalated compounds of niobium and tantalum dicalcogenides

International Nuclear Information System (INIS)

Wypych, F.

1988-01-01

The synthesis of niobium and tantalum lamellar compounds and its intercalated derivatives is described. The intercalated compounds with lithium, with alkaline metal and with metals of the first-row transition are studied, characterized by X-ray diffraction. (C.G.C.) [pt

Metal resistance sequences and transgenic plants

Science.gov (United States)

Meagher, Richard Brian; Summers, Anne O.; Rugh, Clayton L.

1999-10-12

The present invention provides nucleic acid sequences encoding a metal ion resistance protein, which are expressible in plant cells. The metal resistance protein provides for the enzymatic reduction of metal ions including but not limited to divalent Cu, divalent mercury, trivalent gold, divalent cadmium, lead ions and monovalent silver ions. Transgenic plants which express these coding sequences exhibit increased resistance to metal ions in the environment as compared with plants which have not been so genetically modified. Transgenic plants with improved resistance to organometals including alkylmercury compounds, among others, are provided by the further inclusion of plant-expressible organometal lyase coding sequences, as specifically exemplified by the plant-expressible merB coding sequence. Furthermore, these transgenic plants which have been genetically modified to express the metal resistance coding sequences of the present invention can participate in the bioremediation of metal contamination via the enzymatic reduction of metal ions. Transgenic plants resistant to organometals can further mediate remediation of organic metal compounds, for example, alkylmetal compounds including but not limited to methyl mercury, methyl lead compounds, methyl cadmium and methyl arsenic compounds, in the environment by causing the freeing of mercuric or other metal ions and the reduction of the ionic mercury or other metal ions to the less toxic elemental mercury or other metals.

Peracetic Acid Depolymerization of Biorefinery Lignin for Production of Selective Monomeric Phenolic Compounds.

Science.gov (United States)

Ma, Ruoshui; Guo, Mond; Lin, Kuan-Ting; Hebert, Vincent R; Zhang, Jinwen; Wolcott, Michael P; Quintero, Melissa; Ramasamy, Karthikeyan K; Chen, Xiaowen; Zhang, Xiao

2016-07-25

Lignin is the largest source of renewable material with an aromatic skeleton. However, due to the recalcitrant and heterogeneous nature of the lignin polymer, it has been a challenge to effectively depolymerize lignin and produce high-value chemicals with high selectivity. In this study, a highly efficient lignin-to-monomeric phenolic compounds (MPC) conversion method based on peracetic acid (PAA) treatment was reported. PAA treatment of two biorefinery lignin samples, diluted acid pretreated corn stover lignin (DACSL) and steam exploded spruce lignin (SESPL), led to complete solubilization and production of selective hydroxylated monomeric phenolic compounds (MPC-H) and monomeric phenolic acid compounds (MPC-A) including 4-hydroxy-2-methoxyphenol, p-hydroxybenzoic acid, vanillic acid, syringic acid, and 3,4-dihydroxybenzoic acid. The maximized MPC yields obtained were 18 and 22 % based on the initial weight of the lignin in SESPL and DACSL, respectively. However, we found that the addition of niobium pentoxide catalyst to PAA treatment of lignin can significantly improve the MPC yields up to 47 %. The key reaction steps and main mechanisms involved in this new lignin-to-MPC valorization pathway were investigated and elucidated. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High temperature solar selective coatings

Science.gov (United States)

Kennedy, Cheryl E

2014-11-25

Improved solar collectors (40) comprising glass tubing (42) attached to bellows (44) by airtight seals (56) enclose solar absorber tubes (50) inside an annular evacuated space (54. The exterior surfaces of the solar absorber tubes (50) are coated with improved solar selective coatings {48} which provide higher absorbance, lower emittance and resistance to atmospheric oxidation at elevated temperatures. The coatings are multilayered structures comprising solar absorbent layers (26) applied to the meta surface of the absorber tubes (50), typically stainless steel, topped with antireflective Savers (28) comprising at least two layers 30, 32) of refractory metal or metalloid oxides (such as titania and silica) with substantially differing indices of refraction in adjacent layers. Optionally, at least one layer of a noble metal such as platinum can be included between some of the layers. The absorbent layers cars include cermet materials comprising particles of metal compounds is a matrix, which can contain oxides of refractory metals or metalloids such as silicon. Reflective layers within the coating layers can comprise refractory metal silicides and related compounds characterized by the formulas TiSi. Ti.sub.3SiC.sub.2, TiAlSi, TiAN and similar compounds for Zr and Hf. The titania can be characterized by the formulas TiO.sub.2, Ti.sub.3O.sub.5. TiOx or TiO.sub.xN.sub.1-x with x 0 to 1. The silica can be at least one of SiO.sub.2, SiO.sub.2x or SiO.sub.2xN.sub.1-x with x=0 to 1.

Designer HF-Based Fluorination Reagent: Highly Regioselective Synthesis of Fluoroalkenes and gem-Difluoromethylene Compounds from Alkynes

Science.gov (United States)

2015-01-01

Hydrogen fluoride (HF) and selected nonbasic and weakly coordinating (toward cationic metal) hydrogen-bond acceptors (e.g., DMPU) can form stable complexes through hydrogen bonding. The DMPU/HF complex is a new nucleophilic fluorination reagent that has high acidity and is compatible with cationic metal catalysts. The gold-catalyzed mono- and dihydrofluorination of alkynes using the DMPU/HF complex yields synthetically important fluoroalkenes and gem-difluoromethlylene compounds regioselectively. PMID:25260170

Selective removal of heavy metal ions by disulfide linked polymer networks

Energy Technology Data Exchange (ETDEWEB)

Ko, Dongah [Department of Environmental Engineering, Technical University of Denmark, Miljøvej 113, 2800 Kgs. Lyngby (Denmark); Lee, Joo Sung [Graduate School of EEWS, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141 (Korea, Republic of); Patel, Hasmukh A. [Department of Chemistry, Northwestern University, Evanston, IL 60208 (United States); Jakobsen, Mogens H. [Department of Micro and Nano technology, Technical University of Denmark, Ørsteds Plads, 345B, 2800 Kgs. Lyngby (Denmark); Hwang, Yuhoon [Department of Environmental Engineering, Seoul National University of Science and Technology, 232 Gongreung-ro, Nowon-gu, Seoul 01811 (Korea, Republic of); Yavuz, Cafer T. [Graduate School of EEWS, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141 (Korea, Republic of); Hansen, Hans Chr. Bruun [Department of Plant and Environmental Sciences, University of Copenhagen, Frederiksberg, Thorvaldsensvej 40, 1871 Frederiksberg C (Denmark); Andersen, Henrik R., E-mail: henrik@ndersen.net [Department of Environmental Engineering, Technical University of Denmark, Miljøvej 113, 2800 Kgs. Lyngby (Denmark)

2017-06-15

Highlights: • Disulfide/thiol polymer networks are promising as sorbent for heavy metals. • Rapid sorption and high Langmuir affinity constant (a{sub L}) for stormwater treatment. • Selective sorption for copper, cadmium, and zinc in the presence of calcium. • Reusability likely due to structure stability of disulfide linked polymer networks. - Abstract: Heavy metal contaminated surface water is one of the oldest pollution problems, which is critical to ecosystems and human health. We devised disulfide linked polymer networks and employed as a sorbent for removing heavy metal ions from contaminated water. Although the polymer network material has a moderate surface area, it demonstrated cadmium removal efficiency equivalent to highly porous activated carbon while it showed 16 times faster sorption kinetics compared to activated carbon, owing to the high affinity of cadmium towards disulfide and thiol functionality in the polymer network. The metal sorption mechanism on polymer network was studied by sorption kinetics, effect of pH, and metal complexation. We observed that the metal ions–copper, cadmium, and zinc showed high binding affinity in polymer network, even in the presence of competing cations like calcium in water.

Highly selective BSA imprinted polyacrylamide hydrogels facilitated by a metal-coding MIP approach.

Science.gov (United States)

El-Sharif, H F; Yapati, H; Kalluru, S; Reddy, S M

2015-12-01

We report the fabrication of metal-coded molecularly imprinted polymers (MIPs) using hydrogel-based protein imprinting techniques. A Co(II) complex was prepared using (E)-2-((2 hydrazide-(4-vinylbenzyl)hydrazono)methyl)phenol; along with iron(III) chloroprotoporphyrin (Hemin), vinylferrocene (VFc), zinc(II) protoporphyrin (ZnPP) and protoporphyrin (PP), these complexes were introduced into the MIPs as co-monomers for metal-coding of non-metalloprotein imprints. Results indicate a 66% enhancement for bovine serum albumin (BSA) protein binding capacities (Q, mg/g) via metal-ion/ligand exchange properties within the metal-coded MIPs. Specifically, Co(II)-complex-based MIPs exhibited 92 ± 1% specific binding with Q values of 5.7 ± 0.45 mg BSA/g polymer and imprinting factors (IF) of 14.8 ± 1.9 (MIP/non-imprinted (NIP) control). The selectivity of our Co(II)-coded BSA MIPs were also tested using bovine haemoglobin (BHb), lysozyme (Lyz), and trypsin (Tryp). By evaluating imprinting factors (K), each of the latter proteins was found to have lower affinities in comparison to cognate BSA template. The hydrogels were further characterised by thermal analysis and differential scanning calorimetry (DSC) to assess optimum polymer composition. The development of hydrogel-based molecularly imprinted polymer (HydroMIPs) technology for the memory imprinting of proteins and for protein biosensor development presents many possibilities, including uses in bio-sample clean-up or selective extraction, replacement of biological antibodies in immunoassays and biosensors for medicine and the environment. Biosensors for proteins and viruses are currently expensive to develop because they require the use of expensive antibodies. Because of their biomimicry capabilities (and their potential to act as synthetic antibodies), HydroMIPs potentially offer a route to the development of new low-cost biosensors. Herein, a metal ion-mediated imprinting approach was employed to metal-code our

Standard enthalpies of formation of selected Rh2YZ Heusler compounds

International Nuclear Information System (INIS)

Yin, Ming; Nash, Philip

2015-01-01

The standard enthalpies of formation (Δ f H°) of selected ternary Rh-based Rh 2 YZ (Y = Cu, Fe, Mn, Ni, Ru, Ti, V; Z = Al, Ga, In, Si, Ge, Sn) compounds were measured using high temperature direct reaction calorimetry. The measured standard enthalpies of formation (in kJ/mol of atoms) are, for the Heusler compound Rh 2 MnSn (−40.1 ± 3.6), for the B2-structured compounds: Rh 2 FeAl (−48.5 ± 2.9); Rh 2 MnAl (−72.4 ± 2.7); Rh 2 MnGa (−55.3 ± 2.0); Rh 2 MnIn (−35.3 ± 1.9), for the tetragonal compounds: Rh 2 FeSn (−28.9 ± 1.3); Rh 2 TiAl (−97.6 ± 2.2); Rh 2 TiGa (−79.0 ± 1.8); Rh 2 TiSn (−74.7 ± 3.1). Values are compared with those from first principles calculations in published papers and the Open Quantum Materials Database (OQMD). Lattice parameters of these compounds are determined using X-ray diffraction analysis (XRD). Microstructures were characterized using scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). - Highlights: • Standard enthalpies of formation of Rh 2 YZ were measured using a drop calorimeter. • Measured enthalpies agree with first principles data in general. • Lattice parameters and related phase relationships were consistent with literature data. • Rh 2 TiSn of tI8 structure were reported for the first time.

Liquid membrane extraction techniques for trace metal analysis and speciation in environmental and biological matrices

Energy Technology Data Exchange (ETDEWEB)

Ndungu, Kuria

1999-04-01

In this thesis, liquid-membrane-based methods for the analysis of trace metal species in samples of environmental and biological origin were developed. By incorporating extracting reagents in the membrane liquid, trace metal ions were selectively separated from humic-rich natural waters and urine samples, prior to their determination using various instrumental techniques. The extractions were performed in closed flow systems thus allowing easy automation of both the sample clean-up and enrichment. An acidic organophosphorus reagent (DEHPA) and a basic tetraalkylammonium reagent (Aliquat-336) were used as extractants in the membrane liquid to selectively extract and enrich cationic and anionic metal species respectively. A speciation method for chromium species was developed that allowed the determination of cationic Cr(III) species and anionic CR(VI) species in natural water samples without the need of a chromatographic separation step prior to their detection. SLM was also coupled on-line to potentiometric stripping analysis providing a fast and sensitive method for analysis of Pb in urine samples. A microporous membrane liquid-liquid extraction (MMLLE) method was developed for the determination of organotin compounds in natural waters that reduced the number of manual steps involved in the LLE of organotin compounds prior to their CC separation. Clean extracts obtained after running unfiltered humic-rich river water samples through the MMLLE flow system allowed selective determination of all the organotin compounds in a single run using GC-MS in the selected ion monitoring mode (SIM) 171 refs, 9 figs, 4 tabs

Transition metal-catalyzed couplings of alkynes to 1,3-enynes: modern methods and synthetic applications.

Science.gov (United States)

Trost, Barry M; Masters, James T

2016-04-21

The metal-catalyzed coupling of alkynes is a powerful method for the preparation of 1,3-enynes, compounds that are of broad interest in organic synthesis. Numerous strategies have been developed for the homo- and cross coupling of alkynes to enynes via transition metal catalysis. In such reactions, a major issue is the control of regio-, stereo-, and, where applicable, chemoselectivity. Herein, we highlight prominent methods for the selective synthesis of these valuable compounds. Further, we illustrate the utility of these processes through specific examples of their application in carbocycle, heterocycle, and natural product syntheses.

Light alkane (mixed feed selective dehydrogenation using bi-metallic zeolite supported catalyst

Directory of Open Access Journals (Sweden)

Zeeshan Nawaz

2009-12-01

Full Text Available Light alkanes are the important intermediates of many refinery processes and their catalytic dehydrogenation gives corresponding alkenes. The aim behind this experimentation is to investigate reaction behavior of mixed alkanes during direct catalytic dehydrogenation and emphasis has been given to enhance propene. Bi-metallic zeolite supported catalyst Pt-Sn/ZSM-5 was prepared by sequentional impregnation method and characterized by BET, EDS and XRD. Direct dehydrogenation reaction is highly endothermic and its conversion is thermodynamically limited. Results showed that the increase in temperature increases the conversion to some extent but there is no overall effect on selectivity of propene. Increase in time-on-stream (TOS remarkably improves propene selectivity at the expense of lower conversion. The performances of bi-metallic zeolite based catalyst largely affected by coke deposition. The presence of butane and ethane adversely affected propane conversion. Optimum propene selectivity is about 48 %, obtained at 600 oC and time-on-stream 10 h.

[Research progress in CoCr metal-ceramic alloy fabricated by selective laser melting].

Science.gov (United States)

Yan, X; Lin, H

2018-02-09

Cobalt-chromium alloys have been applied to dental porcelain fused to metal (PFM) restorations over the past decades owing to their excellent corrosion resistance, good biocompatibility and low price. The production of CoCr metal-ceramic restorations has always been based on traditional lost-wax casting techniques. However, in recent years, selective laser melting (SLM) is becoming more and more highly valued by dental laboratories and dental practitioners due to its individuation, precision and efficiency. This paper mainly reviews the recent researches on the production process of copings, microstructure, mechanical property, metal-ceramic bond strength, fit of copings, corrosion resistance and biocompatibility of SLM CoCr metal-ceramic alloy.

Effects of thermal desorption on the composition of two coking plant soils: Impact on solvent extractable organic compounds and metal bioavailability

Energy Technology Data Exchange (ETDEWEB)

Biache, Coralie [G2R UMR 7566, Nancy Universite, CNRS, Boulevard des Aiguillettes B.P. 239, F-54506 Vandoeuvre-les-Nancy (France); LIMOS UMR 7137, Nancy Universite, CNRS, Boulevard des Aiguillettes B.P. 239, F-54506 Vandoeuvre-les-Nancy (France)], E-mail: coralie.biache@g2r.uhp-nancy.fr; Mansuy-Huault, Laurence; Faure, Pierre [G2R UMR 7566, Nancy Universite, CNRS, Boulevard des Aiguillettes B.P. 239, F-54506 Vandoeuvre-les-Nancy (France); Munier-Lamy, Colette; Leyval, Corinne [LIMOS UMR 7137, Nancy Universite, CNRS, Boulevard des Aiguillettes B.P. 239, F-54506 Vandoeuvre-les-Nancy (France)

2008-12-15

To evaluate the efficiency and the influence of thermal desorption on the soil organic compartment, contaminated soils from coking plant sites (NM and H) were compared to their counterparts treated with thermodesorption. The extractable organic matter, and the metal content and distribution with soil compartments were studied. In both thermodesorbed soils, PAH (polycyclic aromatic hydrocarbon) degradation exceeded 90%. However, the thermal desorption led not only to a volatilization of the organic compounds but also to the condensation of extractable organic matter. The treatments only affected the Fe and Zn distribution within the more stable fractions, whereas the organic compound degradation did not affect their mobility and availability. - Thermal desorption does not induce a metal mobilization but condensation seems to occur during the treatment.

Characterization, source identification and apportionment of selected metals in TSP in an urban atmosphere.

Science.gov (United States)

Shah, Munir H; Shaheen, N; Jaffar, M

2006-03-01

To understand the metal distribution characteristics in the atmosphere of urban Islamabad, total suspended particulate (TSP) samples were collected on daily 12 h basis, at Quaid-i-Azam University campus, using high volume sampler. The TSP samples were treated with HNO(3)/HClO(4) based wet digestion method for the quantification of eight selected metals; Fe, Zn, Pb, Mn, Cr, Co, Ni and Cd by FAAS method. The monitoring period ran from June 2001 to January 2002, with a total of 194 samples collected on cellulose filters. Effects of different meteorological conditions such as temperature, relative humidity, wind speed and wind direction on selected metal levels were interpreted by means of multivariate statistical approach. Enhanced metal levels for Fe (930 ng/m(3)), Zn (542 ng/m(3)) and Pb (210 ng/m(3)) were found on the mean scale while Mn, Cr, Co and Ni emerged as minor contributors. Statistical correlation study was also conducted and a strong correlation was observed between Pb-Cr (r=0.611). The relative humidity showed some significant influence on atmospheric metal distribution while other meteorological parameters showed weak relationship with TSP metal levels. Regarding the origin of sources of heavy metals in TSP, the statistical procedure identified three source profiles; automobile emissions, industrial/metallurgical units, and natural soil dust. The metal levels were also compared with those reported for other parts of the world which showed that the metal levels in urban atmosphere of Islamabad are in exceedence than those of European industrial and urban sites while comparable with some Asian sites.

Selective conversion of synthesis gas into C2-oxygenated products using mixed-metal homogeneous catalysts

International Nuclear Information System (INIS)

Whyman, R.

1986-01-01

A feature which is a key to any wider utilization of chemistry based on synthesis gas is an understanding of, and more particularly, an ability to control, those factors which determine the selectivity of the C 1 to C 2 transformation during the hydrogenation of carbon monoxide. With the exception of the rhodium-catalyzed conversion of carbon monoxide and hydrogen into ethylene glycol and methanol, in which molar ethylene glycol/methanol selectivities of ca 2/1 may be achieved, other catalyst systems containing metals such as cobalt or ruthenium exhibit only poor selectivities to ethylene glycol. The initial studies in this area were based on the reasoning that, since the reduction of carbon monoxide to C 2 products is a complex, multi-step process, the use of appropriate combinations of metals could generate synergistic effects which might prove more effective (in terms of both catalytic activity and selectivity) than simply the sum of the individual metal components. In particular, the concept of the combination of a good hydrogenation catalyst with a good carbonylation, or ''CO insertion'', catalyst seemed particularly germane. As a result of this approach the authors discovered an unprecedented example of the effect of catalyst promoters, particularly in the enhancement of C 2 /C 1 selectivity, and one which has led to the development of composite mixed-metal homogeneous catalyst systems for the conversion of CO/H 2 into C 2 -oxygenate esters

Selection of ectomycorrhizal willow genotype in phytoextraction of heavy metals.

Science.gov (United States)

Hrynkiewicz, Katarzyna; Baum, Christel

2013-01-01

Willow clones are used for the phytoextraction of heavy metals from contaminated soils and are usually mycorrhizal. The receptiveness of willow clones for mycorrhizal inoculum varies specific to genotype; however, it is unknown if this might have a significant impact on their efficiency in phytoextraction of heavy metals. Therefore, a model system with mycorrhizal and non-mycorrhizal willows of two different genotypes--one with usually stronger natural mycorrhizal colonization (Salix dasyclados), and one with lower natural mycorrhizal colonization (S. viminalis)--was investigated for its efficiency of phytoextraction of heavy metals (Cd, Pb, Cu, Zn) from contaminated soil. Inoculation with the ectomycorrhizal fungus Amanita muscaria significantly decreased the biomass of leaves of both inoculated willow clones, and increased or had no effect on the biomass of trunks and roots of S. dasyclados and S. viminalis, respectively. The concentrations of heavy metals in the biomass of S. dasyclados were in general higher than in S. viminalis irrespective of inoculation with the ectomycorrhizal fungus. Inoculation with A. muscaria significantly decreased the concentration of Cu in the trunks of both Salix taxa, but did not affected the concentrations of other heavy metals in the biomass. In conclusion, stronger receptiveness of willow clones for mycorrhizal inoculum was correlated with an increased total extraction of heavy metals from contaminated soils. Therefore, this seems to be a suitable criterion for effective willow clone selection for phytoremediation. Increased biomass production with relatively constant metal concentrations seems to be a major advantage of mycorrhizal formation of willows in phytoremediation of contaminated soils.

Metal derivatives of organo-phosphorous compounds. Part II : niobium(V) and tantalum(V) derivatives

International Nuclear Information System (INIS)

Puri, D.M.; Singh, Soran

1981-01-01

Reactions between niobium(V) chloride, tantalum(V) chloride and dialkyl/diaryl (Et-, Prsup(i)-, Busup(n)- and Ph-) phosphites have been studied in different molar ratios and under different conditions of temperature and solvent systems. The isolated complex compounds have been characterised on the basis of infrared spectral measurements, elemental analyses and magnetic susceptibility data. The polymeric nature of the products has been indicated by their molecular weights. The coordination of phosphite units to metal atom of the other molecule through phosphoryl oxygen gave rise to O-P-O-bridges. (author)

Bio-functionalized silver nanoparticles for selective colorimetric sensing of toxic metal ions and antimicrobial studies

Science.gov (United States)

Vinod Kumar, V.; Anbarasan, S.; Christena, Lawrence Rene; SaiSubramanian, Nagarajan; Philip Anthony, Savarimuthu

2014-08-01

Hibiscus Sabdariffa (Gongura) plant extracts (leaves (HL) and stem (HS) were used for the first time in the green synthesis of bio-functionalized silver nanoparticles (AgNPs). The bio-functionality of AgNPs has been successfully utilized for selective colorimetric sensing of potentially health and environmentally hazardous Hg2+, Cd2+ and Pb2+ metal ions at ppm level in aqueous solution. Importantly, clearly distinguishable colour for all three metal ions was observed. The influence of extract preparation condition and pH were also explored on the formation of AgNPs. Both selectivity and sensitivity differed for AgNPs synthesized from different parts of the plant. Direct correlation between the stability of green synthesized AgNPs at different pH and its antibacterial effects has been established. The selective colorimetric sensing of toxic metal ions and antimicrobial effect of green synthesized AgNPs demonstrated the multifunctional applications of green nanotechnology.

Synthesis of phthalide-fused indoline by microwave irradiation and preliminary binding study with metal cations

Science.gov (United States)

Ling, Sheryn Wong Shue; Latip, Jalifah; Hassan, Nurul Izzaty; Hasbullah, Siti Aishah

2018-04-01

An efficient and green method of synthesizing phthalide-fused indoline, 3-[(1,3,3-trimethylindolin-2-ylidene)methyl]isobenzofuran-1(3H)-one (3) has been developed by the coupling reaction of 1,3,3-trimethyl-2-methyleneindoline, 1 and phthalaldehydic acid, 2 under solvent-free domestic microwave irradiation. The compound was produced with an excellent yield (98 %) and at a shorter reaction time (5 min) as compared to the conventional method. Compound 3 was fully characterized by analytical and spectral methods. Preliminary binding study of 3 towards different types of metal cations was done by "naked eye" colorimetric detection and UV-vis spectrophotometer. Compound 3 exhibits good selectivity and sensitivity for Sn2+ compared to other metal cations.

Heteroepitaxial growth of 3-5 semiconductor compounds by metal-organic chemical vapor deposition for device applications

Science.gov (United States)

Collis, Ward J.; Abul-Fadl, Ali

1988-01-01

The purpose of this research is to design, install and operate a metal-organic chemical vapor deposition system which is to be used for the epitaxial growth of 3-5 semiconductor binary compounds, and ternary and quaternary alloys. The long-term goal is to utilize this vapor phase deposition in conjunction with existing current controlled liquid phase epitaxy facilities to perform hybrid growth sequences for fabricating integrated optoelectronic devices.

Selective metallization of polymers using laser induced surface activation (LISA)—characterization and optimization of porous surface topography

DEFF Research Database (Denmark)

Zhang, Yang; Hansen, Hans Nørgaard; De Grave, Arnaud

2011-01-01

Laser induced selective activation (LISA) is a molded interconnected devices technique for selective metallization of polymers. On the working piece, only the laser-machined area can be metalized in the subsequent plating. The principle of the technology is introduced. Surface analysis was perfor...

Antimicrobial resistance and its association with tolerance to heavy metals in agriculture production.

Science.gov (United States)

Yu, Zhongyi; Gunn, Lynda; Wall, Patrick; Fanning, Séamus

2017-06-01

Antimicrobial resistance is a recognized public health challenge that since its emergence limits the therapeutic options available to veterinarians and clinicians alike, when treatment is warranted. This development is further compounded by the paucity of new antibiotics. The agri-food industry benefits from the availability of antimicrobial compounds for food-animal production and crop protection. Nonetheless, their improper use can result in the selection for bacteria that are phenotypically resistant to these compounds. Another class of agents used in agriculture includes various cationic metals that can be included in animal diets as nutritional supplements or spread on pastures to support crop growth and protection. Heavy metals, in particular, are giving rise to concerns among public health professionals, as they can persist in the environment remaining stable for prolonged periods. Moreover, bacteria can also exhibit resistance to these chemical elements and the genes encoding this phenotype can be physically localized to plasmids that may also contain one or more antimicrobial resistance-encoding gene(s). This paper reviews our current understanding of the role that bacteria play in expressing resistance to heavy metals. It will describe how heavy metals are used in agri-food production, and explore evidence available to link resistance to heavy metals and antimicrobial compounds. In addition, possible solutions to reduce the impact of heavy metal resistance are also discussed, including using organic minerals and reducing the level of trace minerals in animal feed rations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study on novel ionic liquids as extracting agent for priority metals from waste waters

International Nuclear Information System (INIS)

Fischer, L.; Falta, T.; Stingeder, G.; Koellensperger, G.; Hann, S.; Kogelnig, D.; Stojanovic, A.; Krachler, R.; Keppler, B.K.

2009-01-01

Full text: As the new EU Water Framework Directive (2000/60/EC) sets high environmental quality standards for priority substances in surface water, effective procedures for wastewater treatment are required. The characteristics of ionic liquids (IL) can be adjusted by modifying their ionic composition for liquid-liquid extraction of metals and metal containing compounds (Cd, Hg, Ni, Pb, tributyltin, cancerostatic platinum compounds) from the water phase. The potential of novel IL for selective removal of the above mentioned substances regarding extraction time, pH and matrix were determined by ICPSFMS, HPLC-ICPMS and GC-ICPMS measurements. (author)

Laser-induced selective metallization of polypropylene doped with multiwall carbon nanotubes

Science.gov (United States)

Ratautas, Karolis; Gedvilas, Mindaugas; Stankevičiene, Ina; Jagminienė, Aldona; Norkus, Eugenijus; Pira, Nello Li; Sinopoli, Stefano; Račiukaitis, Gediminas

2017-08-01

Moulded interconnect devices (MID) offer the material, weight and cost saving by integration electronic circuits directly into polymeric components used in automotive and other consumer products. Lasers are used to write circuits directly by modifying the surface of polymers followed by an electroless metal plating. A new composite material - the polypropylene doped with multiwall carbon nanotubes was developed for the laser-induced selective metallization. Mechanism of surface activation by laser irradiation was investigated in details utilising pico- and nanoseconds lasers. Deposition of copper was performed in the autocatalytic electroless plating bath. The laser-activated polymer surfaces have been studied using the Raman spectroscopy and scanning electron microscope (SEM). Microscopic images revealed that surface becomes active only after its melting by a laser. Alterations in the Raman spectra of the D and G bands indicated the clustering of carbon additives in the composite material. Optimal laser parameters for the surface activation were found by measuring a sheet resistance of the finally metal-plated samples. A spatially selective copper plating was achieved with the smallest conductor line width of 22 μm at the laser scanning speed of 3 m/s and the pulse repetition rate of 100 kHz. Finally, the technique was validated by making functional electronic circuits by this MID approach.

Role of 3d electrons in formation of ionic-covalent bonds in II-VI based ternary compounds

International Nuclear Information System (INIS)

Lawniczak-Jablonska, K.; Iwanowski, R.J.; Perera, R.C.C.

1997-01-01

In the II-VI compounds doped with transition metals (diluted magnetic semiconductors) a substitution of cation by the introduced magnetic ion leads to hybridization of its 3d states with the sp states of the host semiconductor. The degree of hybridization of the 3d states and its interaction with the host material band states has been a subject of numerous discussions. Inner shell absorption spectroscopy provides very useful means of electronic structure analysis in a wide variety of systems. Due to its selectivity for atomic species and the selection rules for electron transitions, the soft X-ray absorption technique offers quite unique opportunity to measure directly the site-selective local density of the unoccupied d states in the compounds studied. Results are reported for ZnS compounds with Mn, Fe, Co or Ni substitutions for Zn

Recent Progress in Graphite Intercalation Compounds for Rechargeable Metal (Li, Na, K, Al)‐Ion Batteries

Science.gov (United States)

Xu, Jiantie; Dou, Yuhai; Wei, Zengxi; Li, Yutao; Liu, Huakun; Dou, Shixue

2017-01-01

Abstract Lithium‐ion batteries (LIBs) with higher energy density are very necessary to meet the increasing demand for devices with better performance. With the commercial success of lithiated graphite, other graphite intercalation compounds (GICs) have also been intensively reported, not only for LIBs, but also for other metal (Na, K, Al) ion batteries. In this Progress Report, we briefly review the application of GICs as anodes and cathodes in metal (Li, Na, K, Al) ion batteries. After a brief introduction on the development history of GICs, the electrochemistry of cationic GICs and anionic GICs is summarized. We further briefly summarize the use of cationic GICs and anionic GICs in alkali ion batteries and the use of anionic GICs in aluminium‐ion batteries. Finally, we reach some conclusions on the drawbacks, major progress, emerging challenges, and some perspectives on the development of GICs for metal (Li, Na, K, Al) ion batteries. Further development of GICs for metal (Li, Na, K, Al) ion batteries is not only a strong supplement to the commercialized success of lithiated‐graphite for LIBs, but also an effective strategy to develop diverse high‐energy batteries for stationary energy storage in the future. PMID:29051856

Development of Experimental Setup of Metal Rapid Prototyping Machine using Selective Laser Sintering Technique

Science.gov (United States)

Patil, S. N.; Mulay, A. V.; Ahuja, B. B.

2018-04-01

Unlike in the traditional manufacturing processes, additive manufacturing as rapid prototyping, allows designers to produce parts that were previously considered too complex to make economically. The shift is taking place from plastic prototype to fully functional metallic parts by direct deposition of metallic powders as produced parts can be directly used for desired purpose. This work is directed towards the development of experimental setup of metal rapid prototyping machine using selective laser sintering and studies the various parameters, which plays important role in the metal rapid prototyping using SLS technique. The machine structure in mainly divided into three main categories namely, (1) Z-movement of bed and table, (2) X-Y movement arrangement for LASER movements and (3) feeder mechanism. Z-movement of bed is controlled by using lead screw, bevel gear pair and stepper motor, which will maintain the accuracy of layer thickness. X-Y movements are controlled using timing belt and stepper motors for precise movements of LASER source. Feeder mechanism is then developed to control uniformity of layer thickness metal powder. Simultaneously, the study is carried out for selection of material. Various types of metal powders can be used for metal RP as Single metal powder, mixture of two metals powder, and combination of metal and polymer powder. Conclusion leads to use of mixture of two metals powder to minimize the problems such as, balling effect and porosity. Developed System can be validated by conducting various experiments on manufactured part to check mechanical and metallurgical properties. After studying the results of these experiments, various process parameters as LASER properties (as power, speed etc.), and material properties (as grain size and structure etc.) will be optimized. This work is mainly focused on the design and development of cost effective experimental setup of metal rapid prototyping using SLS technique which will gives the feel of

Mixed valence and metamagnetism in a metal flux grown compound Eu2Pt3Si5

International Nuclear Information System (INIS)

Sarkar, Sumanta; Subbarao, Udumula; Joseph, Boby; Peter, Sebastian C.

2015-01-01

A new compound Eu 2 Pt 3 Si 5 with plate shaped morphology has been grown from excess In flux. The compound crystallizes in the orthorhombic U 2 Co 3 Si 5 structure type, Ibam space group and the lattice parameters are a=10.007(2) Å, b=11.666(2) Å and c=6.0011(12) Å. The crystal structure of this compound can be conceived as inter-twinned chains of [Pt 2 Si 2 ] and [PtSi 3 ] tetrahedra connected along [100] direction to give rise to a complex three dimensional [Pt 3 Si 5 ] network. Temperature dependent magnetic susceptibility data suggests that Eu 2 Pt 3 Si 5 undergoes a strong antiferromagnetic ordering (T N =19 K) followed by a weak ferromagnetic transition (T C =5.5 K). The effective magnetic moment/Eu obtained from susceptibility data is 6.78 μ B accounts mixed valent Eu with almost 85% divalent Eu, which is supported by X-ray absorption near edge spectroscopy. The compound undergoes a metamagnetic transition under applied magnetic field through a probable spin flop mechanism. - Graphical abstract: Eu 2 Pt 3 Si 5 , a new member in the U 2 Co 3 Si 5 (Ibam) family undergoes metamagnetic transition at high magnetic field and Eu is in mixed valence state. - Highlights: • A new compound Eu 2 Pt 3 Si 5 has been synthesized using indium as an inactive metal flux. • The compound undergoes metamagnetic transition at higher field. • Eu in this compound resides in a mixed valence state

Selective Metallization of Well Aligned PS-b-P2VP Block Copolymers in Thin Films and in Confined Geometries

Science.gov (United States)

Sievert, James D.; Watkins, James J.; Russell, Thomas P.

2006-03-01

Well aligned, microphase-separated structures of styrene-2-vinylpyridine block copolymers are being used as templates for macromolecule-metal nanocomposites. These composites are either prepared as thin films or confined in nanoporous aluminum oxide membranes. Under optimal conditions, templates are prepared as thin films or confined nanorods and metallized without disturbing the ordered structure. We have developed a procedure that deposits metal within the polymer using supercritical carbon dioxide-soluble metal precursors. The use of supercritical carbon dioxide allows for selective metallization of the polymer at or below the glass transition, without disrupting the morphology. In addition, similar procedures have been investigated using metal salts and acids. Using these techniques, metals and metal-sulfides including silver, gold, platinum and zinc sulfide have been selectively deposited.

Site-selective electroless nickel plating on patterned thin films of macromolecular metal complexes.

Science.gov (United States)

Kimura, Mutsumi; Yamagiwa, Hiroki; Asakawa, Daisuke; Noguchi, Makoto; Kurashina, Tadashi; Fukawa, Tadashi; Shirai, Hirofusa

2010-12-01

We demonstrate a simple route to depositing nickel layer patterns using photocross-linked polymer thin films containing palladium catalysts, which can be used as adhesive interlayers for fabrication of nickel patterns on glass and plastic substrates. Electroless nickel patterns can be obtained in three steps: (i) the pattern formation of partially quaterized poly(vinyl pyridine) by UV irradiation, (ii) the formation of macromolecular metal complex with palladium, and (iii) the nickel metallization using electroless plating bath. Metallization is site-selective and allows for a high resolution. And the resulting nickel layered structure shows good adhesion with glass and plastic substrates. The direct patterning of metallic layers onto insulating substrates indicates a great potential for fabricating micro/nano devices.

Efficient selective catalytic reduction of NO by novel carbon-doped metal catalysts made from electroplating sludge.

Science.gov (United States)

Zhang, Jia; Zhang, Jingyi; Xu, Yunfeng; Su, Huimin; Li, Xiaoman; Zhou, Ji Zhi; Qian, Guangren; Li, Li; Xu, Zhi Ping

2014-10-07

Electroplating sludges, once regarded as industrial wastes, are precious resources of various transition metals. This research has thus investigated the recycling of an electroplating sludge as a novel carbon-doped metal (Fe, Ni, Mg, Cu, and Zn) catalyst, which was different from a traditional carbon-supported metal catalyst, for effective NO selective catalytic reduction (SCR). This catalyst removed >99.7% NO at a temperature as low as 300 °C. It also removed NO steadily (>99%) with a maximum specific accumulative reduced amount (MSARA) of 3.4 mmol/g. Gas species analyses showed that NO removal was accompanied by evolving N2 and CO2. Moreover, in a wide temperature window, the sludge catalyst showed a higher CO2 selectivity (>99%) than an activated carbon-supported metal catalyst. Structure characterizations revealed that carbon-doped metal was transformed to metal oxide in the sludge catalyst after the catalytic test, with most carbon (2.33 wt %) being consumed. These observations suggest that NO removal over the sludge catalyst is a typical SCR where metals/metal oxides act as the catalytic center and carbon as the reducing reagent. Therefore, our report probably provides an opportunity for high value-added utilizations of heavy-metal wastes in mitigating atmospheric pollutions.

System and process for production of magnesium metal and magnesium hydride from magnesium-containing salts and brines

Science.gov (United States)

McGrail, Peter B.; Nune, Satish K.; Motkuri, Radha K.; Glezakou, Vassiliki-Alexandra; Koech, Phillip K.; Adint, Tyler T.; Fifield, Leonard S.; Fernandez, Carlos A.; Liu, Jian

2016-11-22

A system and process are disclosed for production of consolidated magnesium metal products and alloys with selected densities from magnesium-containing salts and feedstocks. The system and process employ a dialkyl magnesium compound that decomposes to produce the Mg metal product. Energy requirements and production costs are lower than for conventional processing.

Selective transport of metal ions through cation exchange membrane in the presence of a complexing agent

Energy Technology Data Exchange (ETDEWEB)

Tingchia Huang; Jaukai Wang (National Cheng Kung Univ., Tainan (Taiwan, Province of China))

1993-01-01

Selective transport of metal ions through a cation exchange membrane was studied in stirred batch dialyzer for the systems Ni[sup 2+]-Cu[sup 2+] and Cu[sup 2+]-Fe[sup 3+]. Oxalic acid, malonic acid, citric acid, glycine, and ethylenediaminetetraacetic acid were employed as the complexing agents added in the feed solution in order to increase the permselectivity of metal ions. The experimental results show that the selective transport behavior of metal ions depends on the valence and the concentration of metal ions, the stoichiometric ratio of complexing agent to metal ions, and the pH value of the feed solution, but is independent of the concentration of counterion in the stripping phase. A theoretical approach was formulated on the basis of the Nernst-Planck equation and interface quasi-equilibrium. Theoretical solutions obtained from numerical calculation were in agreement with the experimental data.

Oriented Decoration in Metal-Functionalized Ordered Mesoporous Silicas and Their Catalytic Applications in the Oxidation of Aromatic Compounds

Directory of Open Access Journals (Sweden)

Shijian Zhou

2018-02-01

Full Text Available Ordered mesoporous silicas (OMSs attract considerable attention due to their advanced structural properties. However, for the pristine silica materials, the inert property greatly inhibits their catalytic applications. Thus, to contribute to the versatile surface of OMSs, different metal active sites, including acidic/basic sites and redox sites, have been introduced into specific locations (mesoporous channels and framework of OMSs and the metal-functionalized ordered mesoporous silicas (MOMSs show great potential in the catalytic applications. In this review, we first present the categories of metal active sites. Then, the synthesized processes of MOMSs are thoroughly discussed, in which the metal active sites would be introduced with the assistance of organic groups into the specific locations of OMSs. In addition, the structural morphologies of OMSs are elaborated and the catalytic applications of MOMSs in the oxidation of aromatic compounds are illustrated in detail. Finally, the prospects for the future development in this field are proposed.

Conducting metal dithiolate complexes

DEFF Research Database (Denmark)

Underhill, A. E.; Ahmad, M. M.; Turner, D. J.

1985-01-01

Further work on the chemical composition of the one-dimensional metallic metal dithiolene complex Li-Pt(mnt) is reported. The electrical conduction and thermopower properties of the nickel and palladium complexes are reported and compared with those of the platinum compound......Further work on the chemical composition of the one-dimensional metallic metal dithiolene complex Li-Pt(mnt) is reported. The electrical conduction and thermopower properties of the nickel and palladium complexes are reported and compared with those of the platinum compound...

Studies on selected organic-metal interactions of importance in the environment

International Nuclear Information System (INIS)

Mason, Ian.

1995-10-01

This research project investigated the interaction between natural organics acids and selected metal ions. The aims of the project was to provide quantitative data on the speciation of metal ions when placed in systems containing natural organic acids. It was envisaged that such data will assist in the risk assessment of the Drigg low level waste site in Cumbria. The formation and complexing ability of these natural organic acids is discussed and the classing of these acids into high molecular weight organic acids and low molecular weight organic acids. Initial investigations used a potentiometric technique to study the interaction between nickel and europium and selected low molecular weight organic acids which were thought to occur in significant concentrations in soils and groundwaters. These experiments confirmed existing critically assessed literature values, and provided an experimental methodology for further 'in-house' measurement of such values. In addition, studies were also performed on systems containing two competing organic acids. (author)

Selective-area growth and controlled substrate coupling of transition metal dichalcogenides

Science.gov (United States)

Bersch, Brian M.; Eichfeld, Sarah M.; Lin, Yu-Chuan; Zhang, Kehao; Bhimanapati, Ganesh R.; Piasecki, Aleksander F.; Labella, Michael, III; Robinson, Joshua A.

2017-06-01

Developing a means for true bottom-up, selective-area growth of two-dimensional (2D) materials on device-ready substrates will enable synthesis in regions only where they are needed. Here, we demonstrate seed-free, site-specific nucleation of transition metal dichalcogenides (TMDs) with precise control over lateral growth by utilizing an ultra-thin polymeric surface functionalization capable of precluding nucleation and growth. This polymer functional layer (PFL) is derived from conventional photoresists and lithographic processing, and is compatible with multiple growth techniques, precursors (metal organics, solid-source) and TMDs. Additionally, we demonstrate that the substrate can play a major role in TMD transport properties. With proper TMD/substrate decoupling, top-gated field-effect transistors (FETs) fabricated with selectively-grown monolayer MoS2 channels are competitive with current reported MoS2 FETs. The work presented here demonstrates that substrate surface engineering is key to realizing precisely located and geometrically-defined 2D layers via unseeded chemical vapor deposition techniques.

Assessing the resistance and bioremediation ability of selected bacterial and protozoan species to heavy metals in metal-rich industrial wastewater.

Science.gov (United States)

Kamika, Ilunga; Momba, Maggy N B

2013-02-06

Heavy-metals exert considerable stress on the environment worldwide. This study assessed the resistance to and bioremediation of heavy-metals by selected protozoan and bacterial species in highly polluted industrial-wastewater. Specific variables (i.e. chemical oxygen demand, pH, dissolved oxygen) and the growth/die-off-rates of test organisms were measured using standard methods. Heavy-metal removals were determined in biomass and supernatant by the Inductively Couple Plasma Optical Emission Spectrometer. A parallel experiment was performed with dead microbial cells to assess the biosorption ability of test isolates. The results revealed that the industrial-wastewater samples were highly polluted with heavy-metal concentrations exceeding by far the maximum limits (in mg/l) of 0.05-Co, 0.2-Ni, 0.1-Mn, 0.1-V, 0.01-Pb, 0.01-Cu, 0.1-Zn and 0.005-Cd, prescribed by the UN-FAO. Industrial-wastewater had no major effects on Pseudomonas putida, Bacillus licheniformis and Peranema sp. (growth rates up to 1.81, 1.45 and 1.43 d-1, respectively) compared to other test isolates. This was also revealed with significant COD increases (p heavy metals (Co-71%, Ni-51%, Mn-45%, V-83%, Pb-96%, Ti-100% and Cu-49%) followed by Bacillus licheniformis (Al-23% and Zn-53%) and Peranema sp. (Cd-42%). None of the dead cells were able to remove more than 25% of the heavy metals. Bacterial isolates contained the genes copC, chrB, cnrA3 and nccA encoding the resistance to Cu, Cr, Co-Ni and Cd-Ni-Co, respectively. Protozoan isolates contained only the genes encoding Cu and Cr resistance (copC and chrB genes). Peranema sp. was the only protozoan isolate which had an additional resistant gene cnrA3 encoding Co-Ni resistance. Significant differences (p metal-removal and the presence of certain metal-resistant genes indicated that the selected microbial isolates used both passive (biosorptive) and active (bioaccumulation) mechanisms to remove heavy metals from industrial wastewater. This study

Evaluation of wetlands designed to transfer and transform selected metals in an aqueous matrix

International Nuclear Information System (INIS)

Hawkins, W.B.; Gillespie, W.B. Jr.; Rodgers, J.H. Jr.

1995-01-01

Constructed wetlands can be used as an alternative to traditional wastewater treatment. Two wetlands were constructed at a Louisiana petroleum refinery and were used to study transfers and transformations of selected metals (Zn, Pb, and Cu) in a refinery effluent. In order to optimize metal removal from the aqueous matrix and subsequently decrease metal bioavailability, the hydroperiod, hydrosoil, and vegetation were specifically selected and incorporated into the wetland design. To test the metal removal efficiency of the constructed wetlands, refinery effluent was amended with 4 mg Zn/L as ZnCl 2 for 150 d. From influent to effluent, average total recoverable and soluble zinc concentrations decreased by 41 and 72%, respectively. Toxicity tests (7 d) using Ceriodaphnia dubia and Pimephales promelas illustrated a decrease in zinc bioavailability. Average C. dubia survival increased from 0--73% as a result of wetland treatment; for P. promelas, the increase in average survival was 37--94%. Based upon this field experiment, constructed wetlands can be specifically designed for zinc removal and concomitant decreases in toxicity

Ion-beam-mixing in metal-metal systems and metal-silicon systems

International Nuclear Information System (INIS)

Hung, L.

1984-01-01

The influence of energetic ion bombardment on the composition and structure of thin film materials and utilization of ion-beam-mixing techniques to modify interfacial reactions are reported in this thesis. The phase formation in metals by using ion mixing techniques has been studied. Upon ion irradiation of Al/Pt, Al/Pd and Al/Ni thin films, only the simplest intermetallic compounds of PdAl and NiAl were formed in crystalline structure, while the amorphous phase has been observed over a large range of composition. Ion mixing of Au/Cu bilayers resulted in the formation of substitutional solid solutions with no trace of ordered compounds. The formation of the ordered compound CuAu was achieved either by irradiation of bilayers with Ar ions at elevated substrate temperature or by irradiation of the mixed layers with He ions at relatively low temperature. In the Au/Al system several crystal compounds existed in the as-deposited samples. These phases remained crystalline or transformed into other equilibrium compounds upon ion irradiation. The results suggest that the phase formation by ion mixing is dependent on the high quench rate in the collision cascade region and the atomic mobility at the irradiation temperature. The argument can be applied to silicide forming systems. With near-noble metals, the mixed atoms are mobile and form metallurgically distinct phases. With refractory metals, amorphous phases are formed due to lack of atomic mobility

Selective adsorption of volatile organic compounds in micropore aluminum methylphosphonate-alpha: a combined molecular simulation-experimental approach.

Science.gov (United States)

Herdes, Carmelo; Valente, Anabela; Lin, Zhi; Rocha, João; Coutinho, João A P; Medina, Francisco; Vega, Lourdes F

2007-06-19

Results concerning the adsorption capacity of aluminum methylphosphonate polymorph alpha (AlMePO-alpha) for pure ethyl chloride and vinyl chloride by measured individual adsorption isotherms of these pure compounds are presented and discussed here. The experimental data supports the idea of using these materials as selective adsorbents for separating these compounds in mixtures. To explore this possibility further, we have performed grand canonical Monte Carlo simulations using a recently proposed molecular simulation framework for gas adsorption on AlMePO, and the results are presented here. The molecular model of the material was used in a purely transferable manner from a previous work (Herdes, C.; Lin, Z.; Valente, A.; Coutinho, J. A. P.; Vega, L. F. Langmuir 2006, 22, 3097). Regarding the molecular model of the fluids, an existing model for ethyl chloride was improved to capture the experimental dipole value better; an equivalent force field for the vinyl chloride molecule was also developed for simulation purposes. Simulations of the pure compounds were found to be in excellent agreement with the measured experimental data at the three studied temperatures. Simulations were also carried out in a purely predictive manner as a tool to find the optimal conditions for the selective adsorption of these compounds prior experimental measurements are carried out. The influence of the temperature and the bulk composition on the adsorption selectivity was also investigated. Results support the use of AlMePO-alpha as an appropriate adsorbent for the purification process of vinyl chloride, upholding the selective adsorption of ethyl chloride.

Data on heavy metals and selected anions in the Persian popular herbal distillates

OpenAIRE

Keshtkar, Mozhgan; Dobaradaran, Sina; Soleimani, Farshid; Karbasdehi, Vahid Noroozi; Mohammadi, Mohammad Javad; Mirahmadi, Roghayeh; Ghasemi, Fatemeh Faraji

2016-01-01

In this data article, we determined the concentration levels of heavy metals including Pb, Co, Cd, Mn, Mg, Fe and Cu as well as selected anions including NO3− , NO2−, PO4−3 and SO4−2 in the most used and popular herbal distillates in Iran. It is well known that heavy metals may pose a serious health hazard due to their bioaccumulation throughout the trophic chain (“Heavy metals (Cd, Cu, Ni and Pb) content in two fish species of Persian Gulf in Bushehr Port, Iran” (Dobaradaran et al., 2013) [1...

Speciation of heavy metals in garden soils. Evidences from selective and sequential chemical leaching

Energy Technology Data Exchange (ETDEWEB)

Cheng, Zhongqi; Lee, Leda; Dayan, Sara; Grinshtein, Michael [Brooklyn College of The City Univ. of New York, Brooklyn, NY (United States). Environmental Sciences Analytical Cnter; Shaw, Richard [USDA-NRCS NYC Soil Survey, Staten Island, NY (United States)

2011-06-15

Purpose: Gardening (especially food growing) in urban areas is becoming popular, but urban soils are often very contaminated for historical reasons. There is lack of sufficient information as to the bioavailability of soil heavy metals to plants and human in urban environments. This study examines the relative leachability of Cr, Ni, As, Cd, Zn, and Pb for soils with varying characteristics. The speciation and mobility of these metals can be qualitatively inferred from the leaching experiments. The goal is to use the data to shed some light on their bioavailability to plant and human, as well as the basis for soil remediation. Materials and methods: Selective and sequential chemical leaching methods were both used to evaluate the speciation of Cr, Ni, As, Cd, Zn, and Pb in soil samples collected from New York City residential and community gardens. The sequential leaching experiment followed a standard BCR four-step procedure, while selective leaching involved seven different chemical extractants. Results and discussion: The results from selective and sequential leaching methods are consistent. In general, very little of the heavy metals were found in the easily soluble or exchangeable fractions. Larger fractions of Cd and Zn can be leached out than other metals. Lead appears predominantly in the organic or carbonate fractions, of which {proportional_to} 30-60% is in the easily soluble organic fraction. Most As cannot be leached out by any of the extractants used, but it could have been complicated by the ineffective dissolution of oxides by ammonium hydroxylamine. Ni and Cr were mostly in the residual fractions but some released in the oxidizable fractions. Therefore, the leachability of metals follow the order Cd/Zn > Pb > Ni/Cr. Conclusions: Despite of the controversy and inaccuracy surrounding chemical leaching methods for the speciation of metals, chemical leaching data provide important, general, and easy-to-access information on the mobility of heavy metals

Effective and Selective Recovery of Precious Metals by Thiourea Modified Magnetic Nanoparticles

Directory of Open Access Journals (Sweden)

Hsing-Lung Lien

2013-05-01

Full Text Available Adsorption of precious metals in acidic aqueous solutions using thiourea modified magnetic magnetite nanoparticle (MNP-Tu was examined. The MNP-Tu was synthesized, characterized and examined as a reusable adsorbent for the recovery of precious metals. The adsorption kinetics were well fitted with pseudo second-order equation while the adsorption isotherms were fitted with both Langmuir and Freundlich equations. The maximum adsorption capacity of precious metals for MNP-Tu determined by Langmuir model was 43.34, 118.46 and 111.58 mg/g for Pt(IV, Au(III and Pd(II, respectively at pH 2 and 25 °C. MNP-Tu has high adsorption selectivity towards precious metals even in the presence of competing ions (Cu(II at high concentrations. In addition, the MNP-Tu can be regenerated using an aqueous solution containing 0.7 M thiourea and 2% HCl where precious metals can be recovered in a concentrated form. It was found that the MNP-Tu undergoing seven consecutive adsorption-desorption cycles still retained the original adsorption capacity of precious metals. A reductive adsorption resulting in the formation of elemental gold and palladium at the surface of MNP-Tu was observed.

The content changes of selected phenolic compounds during processing of medicinal plants

OpenAIRE

GROŠAFTOVÁ, Blanka

2007-01-01

This work was aimed to the problem of change of the content of selected phenolic substances during treatment and storage of medical plants. Flavonoids represent small, but very important group of phenolic compounds. The biggest attention was paid to quercetin and rutine.Content of phenolic substances was determined by method of micellar electrokinetic capillary chromatography (MECC) in case of 6 medicinal plants usually used in traditional and modern medicine.

Selective extraction of metals from acidic uranium(VI) solutions using neo-tridecano-hydroxamic acid

International Nuclear Information System (INIS)

Bardoncelli, F.; Grossi, G.

1975-01-01

According to this invention neo-alkyl-hydroxamic acids are employed as ion-exchanging agents in processes for liquid-liquid extraction with the aim of separating, purifying dissolved metals and of converting a metal salt solution into a solution of a salt of the same metal but with different anion. In particular it is an objective of this invention to provide a method whereby a molecular pure uranium solution is obtained by selective extraction from a uranium solution delivered by irradiated fuel reprocessing plants and containing plutonium, fission products and other unwanted metals, in which method neo-tridecane-hydroxamic acid is employed as ion exchanger. (Official Gazette)

Metal compounds in zeolites as active components of chemisorption and catalysis. Quantum chemical approach

International Nuclear Information System (INIS)

Zhidomirov, G.M.

1996-01-01

A short review of possible catalitic active sites associated with various types of metal species in zoolite is presented. The structural and electronic peculiarity of aluminum ions in zeolite lattice and their distribution in the lattice are discussed on the basis of quantum chemical calculations in connection with the formation of Broensted activity of zeolites. Various molecular models of Lewis Acid Sites associated the extra-lattice oxide-hydroxide aluminum species have been investigated by means of density functional model cluster calculations using CO molecule as a probe. Probable ways of formation of the selective oxidation center in FeZSM-5 by decomposition of dinitrogen monoxide have been studied by ab-initio quantum chemical calculations. The immediate oxidizing site is reasonably represented by the binuclear iron-hydroxide cluster with peroxo-like fragment located between iron atoms. Various probable intermediates of the selective oxidation center formation resulted from interaction of a hydroperoxide molecule with a lattice titanium ion in titanium silicalite have been investigated by quantum chemical calculations. It was concluded that this reaction requires essential structural reconstruction in the vicinity of the titanium ion. Probability of this structural reconstruction is discussed. Possible reasons of an electron-deficient and electron-enriched state of metal particles entrapped in zoolite cavities are discussed. Also, various probable molecular models of such modified metal particles in zeolite are considered

The marginal fit of selective laser melting-fabricated metal crowns: an in vitro study.

Science.gov (United States)

Xu, Dan; Xiang, Nan; Wei, Bin

2014-12-01

The selective laser melting technique is attracting interest in prosthetic dentistry. The marginal fit is a key criterion for fixed restorations. The purpose of the study was to evaluate the marginal fit of cast cobalt-chromium alloy crowns versus the fit of selective laser melting-fabricated crowns. The marginal gap widths of 36 single crowns (18 selective laser melting-fabricated cobalt-chromium metal crowns and 18 cobalt-chromium cast crowns) were determined with a silicone replica technique. Each crown specimen was cut into 4 sections, and the marginal gap width of each cross section was evaluated by stereomicroscopy (× 100). The Student t test was used to evaluate whether significant differences occurred in the marginal gap widths between the selective laser melting-fabricated and cast cobalt-chromium metal crowns (α=.05). The mean marginal gap width of the cast crowns (170.19 μm) was significantly wider than that of the selective laser melting-fabricated crowns (102.86 μm). Selective laser melting-fabricate cobalt-chromium dental crowns found improved marginal gap widths compared with traditional cast crowns. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Effect of phenolic compounds on the growth of selected probiotic and pathogenic bacteria.

Science.gov (United States)

Pacheco-Ordaz, R; Wall-Medrano, A; Goñi, M G; Ramos-Clamont-Montfort, G; Ayala-Zavala, J F; González-Aguilar, G A

2018-01-01

Fruit extracts from different tissues (pulp, seed and peel) have shown antimicrobial and prebiotic activities related to their phenolic profile, although structure-specific evaluations have not been reported yet. The effect of five phenolic compounds (catechin and gallic, vanillic, ferulic and protocatechuic acids) identified in different fruits, particularly in mango, was evaluated on the growth of two probiotic (Lactobacillus rhamnosusGG ATCC 53103 and Lactobacillus acidophilusNRRLB 4495) and two pathogenic (Escherichia coli 0157:H7 ATCC 43890 and Salmonella enterica serovar Typhimurium ATCC 14028) bacteria. The minimal inhibitory concentration (MIC) and minimal bactericidal concentration (MBC) of phenolic acids ranged from 15-20 mmol l -1 and 20-30 mmol l -1 against E. coli and S. Typhimurium, respectively. For catechin, the MIC and MBC were 35 mmol l -1 and >35 mmol l -1 against E. coli and S. Typhimurium, respectively. The presence of catechin and gallic, protocatechuic and vanillic acids in MRS broth without dextrose allowed the growth of lactobacilli. Catechin combined with protocatechuic or vanillic acid mildly allowed the growth of both probiotics. In conclusion, phenolic compounds can selectively inhibit the growth of pathogenic bacteria without affecting the viability of probiotics. This study provides relevant information about the effects of phenolic compounds commonly present in fruit and vegetables on the growth of probiotic and pathogenic bacteria. The compounds selectively allowed the growth of probiotic lactobacilli (Lactobacillus rhamnosus GG and Lactobacillus acidophilus) and inhibited pathogenic bacteria (Escherichia coli and Salmonella Typhimurium) at the same concentration (20 mmol l -1 ). These findings can contribute to the formulation of nutraceutical products, such as synbiotics, that can restore or maintain an optimal composition of human microbiota, potentially improving the overall health of the consumer. © 2017 The

Methanol, ethanol and hydrogen sensing using metal oxide and metal (TiO(2)-Pt) composite nanoclusters on GaN nanowires: a new route towards tailoring the selectivity of nanowire/nanocluster chemical sensors.

Science.gov (United States)

Aluri, Geetha S; Motayed, Abhishek; Davydov, Albert V; Oleshko, Vladimir P; Bertness, Kris A; Sanford, Norman A; Mulpuri, Rao V

2012-05-04

We demonstrate a new method for tailoring the selectivity of chemical sensors using semiconductor nanowires (NWs) decorated with metal and metal oxide multicomponent nanoclusters (NCs). Here we present the change of selectivity of titanium dioxide (TiO(2)) nanocluster-coated gallium nitride (GaN) nanowire sensor devices on the addition of platinum (Pt) nanoclusters. The hybrid sensor devices were developed by fabricating two-terminal devices using individual GaN NWs followed by the deposition of TiO(2) and/or Pt nanoclusters (NCs) using the sputtering technique. This paper present the sensing characteristics of GaN/(TiO(2)-Pt) nanowire-nanocluster (NWNC) hybrids and GaN/(Pt) NWNC hybrids, and compare their selectivity with that of the previously reported GaN/TiO(2) sensors. The GaN/TiO(2) NWNC hybrids showed remarkable selectivity to benzene and related aromatic compounds, with no measurable response for other analytes. Addition of Pt NCs to GaN/TiO(2) sensors dramatically altered their sensing behavior, making them sensitive only to methanol, ethanol and hydrogen, but not to any other chemicals we tested. The GaN/(TiO(2)-Pt) hybrids were able to detect ethanol and methanol concentrations as low as 100 nmol mol(-1) (ppb) in air in approximately 100 s, and hydrogen concentrations from 1 µmol mol(-1) (ppm) to 1% in nitrogen in less than 60 s. However, GaN/Pt NWNC hybrids showed limited sensitivity only towards hydrogen and not towards any alcohols. All these hybrid sensors worked at room temperature and are photomodulated, i.e. they responded to analytes only in the presence of ultraviolet (UV) light. We propose a qualitative explanation based on the heat of adsorption, ionization energy and solvent polarity to explain the observed selectivity of the different hybrids. These results are significant from the standpoint of applications requiring room-temperature hydrogen sensing and sensitive alcohol monitoring. These results demonstrate the tremendous potential for

Quantification of Selected Vapour-Phase Compounds using Thermal Desorption-Gas Chromatography

Directory of Open Access Journals (Sweden)

McLaughlin DWJ

2014-12-01

Full Text Available A robust method for the analysis of selected vapour phase (VP compounds in mainstream smoke (MSS is described. Cigarettes are smoked on a rotary smoking machine and the VP that passes through the Cambridge filter pad collected in a TedlarA¯ bag. On completion of smoking, the bag contents are sampled onto an adsorption tube containing a mixed carbon bed. The tube is subsequently analysed on an automated thermal desorption (TD system coupled to a gas chromatography-flame ionization detector (GC-FID using a PoraPLOT-Q column. Quantification of 14 volatile compounds including the major carbonyls is achieved. Details of the method validation data are included in this paper. This method has been used to analyse the VP of cigarette MSS over a wide range of ‘tar’ deliveries and configurations with excellent repeatability. Results for the University of Kentucky reference cigarette 1R4F are in good agreement with reported values.

Characterisation of selected volatile organic compounds in ...

African Journals Online (AJOL)

GCMS), was used to identify volatile compounds at three different temperatures. Fifty volatile compounds, inclusive of 14 acids, 14 alcohols, and 22 esters were identified and quantified in the two brands of indigenous banana beer samples. Only 12 ...

Magnetron sputtering cluster apparatus for formation and deposition of size-selected metal nanoparticles

DEFF Research Database (Denmark)

Hanif, Muhammad; Popok, Vladimir

2015-01-01

selection is achieved using an electrostatic quadrupole mass selector. The deposited silver clusters are studied using atomic force microscopy. The height distributions show typical relative standard size deviation of 9-13% for given sizes in the range between 5-23 nm. Thus, the apparatus demonstrates good...... capability in formation of supported size-selected metal nanoparticles with controllable coverage for various practical applications....

Bis(1,3-dithiole) Compounds

DEFF Research Database (Denmark)

Andersen, Jan Rud; Engler, E. M.; Green, D. C.

1977-01-01

There is described the preparation of bis-1,3-dithiole compounds (I) which are key synthetic precursors for the preparation of new polymeric metal bis(dithiolene) (i.e., II) and tetrathiafulvalene compounds (i.e., III): (Image Omitted)...

Airborne Release of Particles in Overheating Incidents Involving Plutonium Metal and Compounds

Energy Technology Data Exchange (ETDEWEB)

Schwendiman, L. C.; Mishima, J.; Radasch, C. A. [Battelle Memorial Institute, Pacific Northwest Laboratory, Richland, WA (United States)

1968-12-15

Ever-increasing utilization of nuclear fuels will result in wide-scale plutonium recovery processing, reconstitution of fuels, transportation, and extensive handling of this material. A variety of circumstances resulting in overheating and fires involving plutonium may occur, releasing airborne particles. This work describes the observations from a study in which the airborne release of plutonium and its compounds was measured during an exposure of the material of interest containing plutonium to temperatures which may result from fires. Aerosol released from small cylinders of metallic plutonium ignited in air at temperatures from 410 to 650 Degree-Sign C ranged from 3 x 10{sup -6} to 5 x 10{sup -5} wt%. Particles smaller than 15{mu}m in diameter represented as much as 0.03% of the total released. Large plutonium pieces weighing from 456 to 1770 g were ignited and allowed to oxidize completely in air with a velocity of around 500 cm/sec. Release rates of from 0.0045 to 0.032 wt% per hour were found. The median mass diameter of airborne material was 4 {mu}m. Quenching the oxidation with magnesium oxide sand reduced the release to 2.9 X 10{sup -4} wt% per hour. Many experiments were carried out in which plutonium compounds as powders were heated at temperatures ranging from 700 to 1000 Degree-Sign C with several air flows. Release rates ranged from 5 x 10{sup -8} to 0.9 wt% per hour, depending upon the compound and the conditions imposed. The airborne release from boiling solutions of plutonium nitrate were roughly related to energy of boiling, and ranged from 4 x 10{sup -4} to 2 x 10{sup -1} % for the evaporation of 90% of the solution. The fraction airborne when combustibles contaminated with plutonium are burned is under study. The data reported can be used in assessing the consequences of off-standard situations involving plutonium and its compounds in fires. (author)

Transition metal-catalyzed carbocyclization of nitrogen and oxygen-tethered 1,n-enynes and diynes: synthesis of five or six-membered heterocyclic compounds.

Science.gov (United States)

Zhang, Di-Han; Zhang, Zhen; Shi, Min

2012-10-25

Cycloisomerization of 1,n-enynes and diynes is a powerful method in organic synthesis to access heterocyclic compounds and has drawn increasing attention from organic chemists. In this paper, we attempted to summarize our recent results on the transition metal-catalyzed cycloisomerization to synthesize five or six-membered heterocyclic compounds using 1,n-enynes and diynes having a propargylic ester moiety. First, we will describe the synthesis of 2,3-disubstituted 3-pyrrolines via gold catalyzed cycloisomerization of 1,6-diynes. In addition, we will also disclose a novel silver catalyzed tandem 1,3-acyloxy migration/Mannich-type addition/elimination of the sulfonyl group of N-sulfonylhydrazone-propargylic esters to 5,6-dihydropyridazin-4-one derivatives. Furthermore, we will introduce three interesting examples of the synthesis of bicyclic compounds via titanium or rhodium catalyzed carbocyclization of enynes. In this context, we have presented that 1,n-enynes and diynes containing propargylic esters are highly reactive and useful starting materials for the cycloisomerization catalyzed by a transition metal catalyst.

Cluster harvesting by successive reduction of a metal halide with a nonconventional reduction agent: a benefit for the exploration of metal-rich halide systems.

Science.gov (United States)

Ströbele, Markus; Mos, Agnieszka; Meyer, Hans-Jürgen

2013-06-17

The preparation of thermally labile compounds is a great temptation in chemistry which requires a careful selection of reaction media and reaction conditions. With a new scanning technique denoted here as Cluster Harvesting, a whole series of metal halide compounds is detected by differential thermal analysis (DTA) in fused silica tubes and structurally characterized by X-ray powder diffraction. Experiments of the reduction of tungsten hexahalides with elemental antimony and iron are presented. A cascade of six compounds is identified during the reduction with antimony, and five compounds or phases are monitored following the reduction with iron. The crystal structure of Fe2W2Cl10 is reported, and two other phases in the Fe-W-Cl system are discussed.

Removal of nitrogen compounds from gasification gas by selective catalytic or non-catalytic oxidation; Typpiyhdisteiden poisto kaasutuskaasusta selektiivisellae katalyyttisellae ja ei-katalyyttisellae hapetuksella

Energy Technology Data Exchange (ETDEWEB)

Leppaelahti, J.; Koljonen, T. [VTT Energy, Espoo (Finland)

1996-12-01

In gasification reactive nitrogenous compounds are formed from fuel nitrogen, which may form nitrogen oxides in gas combustion. In fluidized bed gasification the most important nitrogenous compound is ammonia (NH{sub 3}). If ammonia could be decomposed to N{sub 2} already before combustion, the emissions if nitrogen oxides could be reduced significantly. One way of increasing the decomposition rate of NH{sub 3} could be the addition of suitable reactants to the gas, which would react with NH{sub 3} and produce N{sub 2}. The aim of this research is to create basic information, which can be used to develop a new method for removal of nitrogen compounds from gasification gas. The reactions of nitrogen compounds and added reactants are studied in reductive atmosphere in order to find conditions, in which nitrogen compounds can be oxidized selectively to N{sub 2}. The project consists of following subtasks: (1) Selective non-catalytic oxidation (SNCO): Reactions of nitrogen compounds and oxidizers in the gas phase, (2) Selective catalytic oxidation (SCO): Reactions of nitrogen compounds and oxidizers on catalytically active surfaces, (3) Kinetic modelling of experimental results in co-operation with the Combustion Chemistry Research Group of Aabo Akademi University. The most important finding has been that NH{sub 3} can be made to react selectively with the oxidizers even in the presence of large amounts of CO and H{sub 2}. Aluminium oxides were found to be the most effective materials promoting selectivity. (author)

Group 11 Metal Compounds with Tripodal Bis(imidazole Thioether Ligands. Applications as Catalysts in the Oxidation of Alkenes and as Antimicrobial Agents

Directory of Open Access Journals (Sweden)

Armando Varela-Ramírez

2011-08-01

Full Text Available New group 11 metal complexes have been prepared using the previously described tripodal bis(imidazole thioether ligand (N-methyl-4,5-diphenyl-2-imidazolyl2C(OMeC(CH32S(tert-Bu ({BITOMe,StBu}, 2. The pincer ligand offers a N2S donor atom set that can be used to coordinate the group 11 metals in different oxidation states [AuI, AuIII, AgI, CuI and CuII]. Thus the new compounds [Au{BITOMe,StBu}Cl][AuCl4]2 (3, [Au{BITOMe,StBu}Cl] (4, [Ag{BITOMe,StBu}X] (X = OSO2CF3- 5, PF6- 6 and [Cu{BITOMe,StBu}Cl2] (7 have been synthesized from reaction of 2 with the appropriate metal precursors, and characterized in solution. While attempting characterization in the solid state of 3, single crystals of the neutral dinuclear mixed AuIII-AuI species [Au2{BITOMe,S}Cl3] (8 were obtained and its crystal structure was determined by X-ray diffraction studies. The structure shows a AuIII center coordinated to the pincer ligand through one N and the S atom. The soft AuI center coordinates to the ligand through the same S atom that has lost the tert-butyl group, thus becoming a thiolate ligand. The short distance between the AuI-AuIII atoms (3.383 Å may indicate a weak metal-metal interaction. Complexes 2-7 and the previously described CuI compound [Cu{BITOMe,StBu}]PF6 (9 have been evaluated in the oxidation of biphenyl ethylene with tert-butyl hydrogen peroxide (TBHP as the oxidant. Results have shown that the AuI and AgI complexes 4 and 6 (at 10 mol % loading are the more active catalysts in this oxidative cleavage. The antimicrobial activity of compounds 2-5, 7 and 9 against Gram-positive and Gram-negative bacteria and yeast has also been evaluated. The new gold and silver compounds display moderate to high antibacterial activity, while the copper derivatives are mostly inactive. The gold and silver complexes were also potent against fungi. Their cytotoxic properties have been analyzed in vitro utilizing HeLa human cervical carcinoma cells. The compounds displayed a

Selective gettering of hydrogen in high pressure metal iodide lamps

International Nuclear Information System (INIS)

Kuus, G.

1976-01-01

One of the main problems in the manufacture of high pressure gas discharge lamps is the elimination of gaseous impurities from their arc tubes. Long degassing processes of all the lamp components are necessary in order to produce lamps with a low ignition voltage and good maintenance of the radiation properties. The investigation described deals with a selective getter place in the arc tube which can replace the long degassing process. The getter consists of a piece of yttrium encapsulated in thin tantalum foil. By this way it is possible to use the gettering action of tantalum and yttrium without having reaction between the metal iodide of the arc tube and yttrium. Yttrium is used because this metal can adsorb a large quantity of hydrogen even at a temperature of 1000 0 C. Hydrogen forms the main gaseous impurity in the high pressure metal iodide lamp. For this reason the adsorption properties like adsorption rate and capacity of the tantalum--yttrium getter for hydrogen are examined, and the results obtained from lamp experiments are given

Reactions of metal ions and their clusters in the gas phase using laser ionization: ion cyclotron resonance spectroscopy

International Nuclear Information System (INIS)

Freiser, B.S.

1981-04-01

Two subjects are discussed in this report: advances in proposed studies on metal ion chemistry and expansion of laboratory facilities. The development of a combined pulsed laser source-ion cyclotron resonance spectrometer has proven to be a convenient and powerful method for generating metal ions and for studying their subsequent chemistry in the gas phase. The main emphasis of this research has been on the application of metal ions as a selective chemical ionization reagents and progress in this area are discussed. The goal is to identify trends in reactivity i.e. mechanisms useful in interpreting the chemical ionization spectra of unknown compounds and to test for the functional group selectivity of the various metal ions. The feasibility of these goals have been demonstrated in extensive studies on Cu + with esters and ketones, on Fe + with ethers, ketones, and hydrocarbons, and on Ti + with hydrocarbons. In addition, preliminary results on sulfur containing compounds and on a variety of other metallic ions have been obtained. Laboratory facilities were expanded from one ion cyclotron resonance (ICR) spectrometer to two, plus a third instrument the Fourier Transform Ion Cyclotron Resonance (FTICR) spectrometer

Technique for detecting liquid metal leaks

International Nuclear Information System (INIS)

Bauerle, J.E.

1979-01-01

In a system employing flowing liquid metal as a heat transfer medium in contact with tubular members containing a working fluid, i.e., steam, liquid metal leaks through the wall of the tubular member are detected by dislodging the liquid metal compounds forming in the tubular member at the leak locations and subsequently transporting the dislodged compound in the form of an aerosol to a detector responsive to the liquid metal compound. In the application to a sodium cooled tubular member, the detector would consist of a sodium responsive device, such as a sodium ion detector

Gases and carbon in metals - thermodynamics, kinetics, and properties. Pt. 11

International Nuclear Information System (INIS)

Jehn, H.; Speck, H.; Fromm, E.; Hoerz, G.

1980-01-01

This issue is part of a series of data on Gases and Carbon in Metals which supplements the data compilation in the book Gase and Kohlenstoff in Metallen (Gases and Carbon in Metals), edited by E.Fromm and E.Gebhardt, Springer-Verlag, Berlin 1976. The present survey includes results from papers published after the copy deadline and recommends critically selected data. Furthermore it comprises a bibliography of relevant literature. For each element the information is given in two parts. In a first section data are listed and in a second section the relevant literature is compiled. For each element, firstly data on binary systems are presented, starting with hydrogen and followed by carbon, nitrogen, oxygen, and rare gases. Within one metal-metalloid system the data are listed under topics such as solubility, solubility limit, dissociation pressure of compounds, vapour pressure of volatile oxides, thermodynamic data, diffusion, transport parameters (effective valence, heat of transport), permeation of gases through metals, gas absorption and gas desorption kinetics, compound formation kinetics, precipitation kinetics, and property changes. (orig./GE)

Organometallic compounds in the environment

National Research Council Canada - National Science Library

Craig, P. J

2003-01-01

... of Organometallic Species in the Environment 20 1.10 Stability of Organometallic Compounds in Biological Systems 1.11 G eneral Comments on the Toxicities of Organometallic Compounds 22 1.12 General Considerations on Environmental R eactivity of Organometallic Compounds 24 1.13 Microbial Biotransformation of Metals and M etalloids 25 1.13.1 Introduction 25 1...

Comparison of UV irradiation and p-fluorphenylaline as selective agents for production of aromatic compounds in plant cell culture

International Nuclear Information System (INIS)

Quesnel, A.A.; Ellis, B.E.

1989-01-01

Resistance to UV irradiation, and to the toxicity of p-fluorophenylalanine, can both be mediateted in plants by enhanced synthesis of aromatic compounds. These selective agents were applied to cell cultures of Nicotiana tabacum, Anchusa officinalis and Catharanthus roseur, and the production of aromatic metabolites in the resulting resistant lines of each species was compared. While Nicotiana and Anchusa cultures responded to each selective agent ith an enhanced accumulation of aromatic compounds, the Catharanthus cultures acquired resistance through other, unknown, mechanisms. Some degree of cross-resistance was observed between cultures selected individually for resistance to each agent (author). 26 refs.; 2 figs.; 1 tab

Estimation of metal uptake in plant parts of roadside grown maize at selected growth stages

OpenAIRE

Anongo, M'ember C.; Uyovbisere, Edward O.; Ekong, Nsima J.

2015-01-01

Health risk assessment of heavy metals in roadside grown foodcrops consumed by humans is a very good technique because such assessment would provide information about any threat regarding heavy metal contamination. Plant and corresponding soil samples were collected for trace metal analysis to ascertain potential health risks. The non-significant differences of lead (Pb) and cadmium (Cd) levels among the selected growth stages shows that the levels of Pb and Cd in the foodcrops were not influ...

Zirconium-based metal organic frameworks: Highly selective adsorbents for removal of phosphate from water and urine

Energy Technology Data Exchange (ETDEWEB)

Lin, Kun-Yi Andrew, E-mail: linky@nchu.edu.tw [Department of Environmental Engineering, National Chung Hsing University, 250 Kuo-Kuang Road, Taichung, Taiwan (China); Chen, Shen-Yi [Department of Environmental Engineering, National Chung Hsing University, 250 Kuo-Kuang Road, Taichung, Taiwan (China); Jochems, Andrew P. [New Mexico Bureau of Geology & Mineral Resources and New Mexico Institute of Mining & Technology, Socorro, NM (United States)

2015-06-15

Phosphate is one of the most concerning compounds in wastewater streams and a main nutrient that causes eutrophication. To eliminate the phosphate pollution, Metal Organic Frameworks (MOFs) are proposed in this study as adsorbents to remove phosphate from water. The zirconium-based MOF, UiO-66, was selected as representative MOF given its exceptional stability in water. To investigate the effect of an amine functional group, UiO-66-NH2 was also prepared using an amine-substituted ligand. The adsorption kinetics and isotherm reveal that UiO-66-NH2 exhibited higher adsorption capacities than UiO-66 possibly due to the amine group. However, the interaction between phosphate and zirconium sites of UiO MOFs might be the primary factor accounting for the phosphate adsorption to UiO MOFs. UiO MOFs also exhibited a high selectivity towards phosphate over other anions such as bromate, nitrite and nitrate. Furthermore, UiO MOFs were found to adsorb phosphate and to completely remove diluted phosphate in urine. We also found that UiO MOFs could be easily regenerated and re-used for phosphate adsorption. These findings suggest that UiO MOFs can be effective and selective adsorbents to remove phosphate from water as well as urine. - Highlights: • UiO-66 as the first type of MOFs was used to remove phosphate from water and urine. • The amine group in UiO MOFs was found to enhance the phosphate adsorption. • UiO-66 exhibited a high adsorption selectivity towards phosphate over other anions. • UiO-66 could be easily regenerated and re-used with 85% regeneration efficiency.

Synthesis and characterization of one- to three-dimensional compounds composed of paradodecatungstate-B cluster and transition metals as linkers

International Nuclear Information System (INIS)

Sun Chunyan; Liu Shuxia; Xie Linhua; Wang Chunling; Gao Bo; Zhang Chundan; Su Zhongmin

2006-01-01

Three new extended frameworks built from paratungstate and transition metals have been synthesized and characterized. In the compound Na 8 [{Cd (H 2 O) 2 }(H 2 W 12 O 42 )].32H 2 O (1), two neighboring paratungstate-B ions [H 2 W 12 O 42 ] 10- are linked by [Cd(H 2 O) 2 ] 2+ units, leading to the formation of infinite one-dimensional (1D) anion chain [{Cd(H 2 O) 2 }(H 2 W 12 O 42 )] n 8n- . The anion [{Co(H 2 O) 3 }{Co(H 2 O) 4 }(H 2 W 12 O 42 )] n 6n- of the compound Na 6 [{Co(H 2 O) 3 }{Co(H 2 O) 4 }(H 2 W 12 O 42 )].29H 2 O (2) shows a layer-like (2D) structure in which paratungstate-B units are linked by CoO 6 octahedra, while the anion [{Co(H 2 O) 3 } 3 (H 2 W 12 O 42 )] n 4n- of the compound (H 3 O + ) 3 [{Na(H 2 O) 4 }{Co(H 2 O) 4 } 3 (H 2 W 12 O 42 )].24.5H 2 O (3) is a three-dimensional (3D) anionic polymer that consists of paratungstate-B units linked by CoO 6 octahedra. Compound 3 can reversibly adsorb and desorb water molecules leading to the color reversibly change from pink to violet. The preliminary magnetic measurement and electrochemical properties of compounds are performed. The crystal structure of unexpected product Na 4 [NiW 6 O 24 H 6 ].13H 2 O (4) is described here for the rare report of crystal structure information on the Anderson-type polyoxotungstate which has nickel as a heteroatom. - Graphical abstract: Three new compounds with one- to three-dimensional extended frameworks built from [H 2 W 12 O 42 ] 10- anion and transition metals have been synthesized and characterized by elemental analyses, X-ray single-crystal analyses, magnetic measurement, XRPD, and cyclic voltammetry measurements. The cobalt containing compound exhibits interesting reversible sorption/desorption of water molecules

Catalytic ozonation not relying on hydroxyl radical oxidation: A selective and competitive reaction process related to metal-carboxylate complexes

KAUST Repository

Zhang, Tao; Croue, Jean-Philippe

2014-01-01

Catalytic ozonation following non-hydroxyl radical pathway is an important technique not only to degrade refractory carboxylic-containing organic compounds/matter but also to avoid catalyst deactivation caused by metal-carboxylate complexation

Spray pyrolysis synthesis of γ-Al_2O_3 supported metal and metal phosphide catalysts and their activity in the hydrodeoxygenation of a bio-oil model compound

International Nuclear Information System (INIS)

Ly, Hoang Vu; Im, Kyungmin; Go, Youngchae; Galiwango, Emmanuel; Kim, Seung-Soo; Kim, Jinsoo; Choi, Jae Hyung; Woo, Hee Chul

2016-01-01

Highlights: • Spherical γ-Al_2O_3 supported metal and metal phosphide catalysts were synthesized by spray pyrolysis method. • Hydrodeoxygenation (HDO) of 2-furyl methyl ketone (FMK) was conducted using metal/metal phosphide catalysts. • FMK was converted into 2-allyl furan and methyl cyclohexane. • The highest FMK conversion of 83% was achieved over 10 wt% Ni/γ-Al_2O_3 catalysts at reaction temperature of 400 °C. - Abstract: In this study, spherical γ-Al_2O_3 supported metal and metal phosphide (Ni, Co, Ni_2P and CoP) catalysts were successfully prepared by combining sol-gel and spray pyrolysis methods. First boehmite sol was prepared based on the Yoldas process and then the corresponding metal salts were added to the sol at the desired concentration, followed by spray pyrolysis of the mixed solution. As the well-mixed solution was transformed to spherical γ-Al_2O_3 supported metal and metal phosphide catalysts during spray pyrolysis process, the metal species were uniformly distributed in the mesoporous γ-Al_2O_3 supports. The product catalysts were investigated under different conditions for hydrodeoxygenation of bio-oil model compound, 2-furyl methyl ketone (FMK), which is the main component of the bio-oil product from pyrolysis of Saccharina japonica. Among the investigated catalysts, the 10 wt% Ni/γ-Al_2O_3 catalyst after calcination at 800 °C showed the highest FMK conversion of 83.02% at the reaction temperature of 400 °C. The gas and liquid products were analyzed by gas chromatography (GC) with TCD/FID detectors and GC–MS, respectively, to determine the product compositions.

Analysis of heavy metals in selected medicinal plants from Dir, Swat and Peshawar districts of Khyber Pakhtunkhwa

International Nuclear Information System (INIS)

Hussain, I.; Khattak, M.R.; Khan, F.A.; Rehman, I.; Khan, F.U.

2011-01-01

Essential and non-essential heavy metals like Manganese, Zinc, Iron, Nickel, Copper, Chromium, Lead and Cadmium were analyzed quantitatively in selected medicinal plants including, Acorus calamus, Artemisia annua, Chenopodium foliosum, Cupressus arizonica, Euphorbia helioscopia L, Lepidium sativum, Nerium oleander, Ranunculus mariculatus , Tecoma stans, Urtica dioica by using atomic absorption spectrometry. The main purpose of this study was to quantify essential and non-essential heavy metals in selected herbs, which are extensively used in the preparation of herbal products and standardized extracts. The high conc. of iron, Mn was found in Nerium oleander 26.52 mg/kg, 94.40 mg/kg. Zn in Lepidium sativum 77.00 mg/kg and high conc. of K 94600 and Na 400 mg/kg was found in Tecoma stans. The concentration of other heavy metals particularly Cu, Ni and Pb were also found in higher conc. in the selected herbs. The main purpose of the present study was to evaluate the contents of toxic metals and their concentration level which may have adverse effect on human health, besides providing a scientific data. (author)

Rare-earth metal compounds with a novel ligand 2-methoxycinnamylidenepyruvate: A thermal and spectroscopic approach

Energy Technology Data Exchange (ETDEWEB)

Carvalho, C.T., E-mail: claudiocarvalho@ufgd.edu.br [Federal University of Grande Dourados, UFGD, 79.804-970 Dourados, MS (Brazil); Oliveira, G.F. [Federal University of Grande Dourados, UFGD, 79.804-970 Dourados, MS (Brazil); Fernandes, J. [Federal University of Grande Dourados, UFGD, 79.804-970 Dourados, MS (Brazil); Federal University of Mato Grosso, UFMT, 78.060-900 Cuiabá, MT (Brazil); Federal University of Goiás, UFG, 74.690-900, Goiânia, GO (Brazil); Institute of Chemistry, UNESP, 14.801-970 Araraquara, SP (Brazil); Siqueira, A.B. [Federal University of Mato Grosso, UFMT, 78.060-900 Cuiabá, MT (Brazil); Ionashiro, E.Y. [Federal University of Goiás, UFG, 74.690-900, Goiânia, GO (Brazil); Ionashiro, M. [Institute of Chemistry, UNESP, 14.801-970 Araraquara, SP (Brazil)

2016-08-10

Highlights: • 2-Methoxycinnamylidenepyruvate as a novel ligand for the synthesis of complexes. • Complexes with well-defined structural arrangements. • Thermal decomposition dependent on the nature of the metal ion. • Study by TG/FT-IR and TG/MS of the gaseous products released. • Potential technological application. - Abstract: Compounds of 2-methoxycinnamylidenepyruvate with trivalent lanthanide ions (Tb, Ho, Er, Tm, Yb and Lu) were obtained in solid state and studied mainly in terms of their thermal and spectroscopic properties. The analyses of the characterization were performed by thermogravimetric system coupled to a mass and infrared spectrometer (TG–DTA/MS and TG–DTA/FT-IR), X-ray powder diffractometry, differential scanning calorimetry (DSC), infrared (FT-IR), preliminary study of fluorescence as well as classical technique of titration with EDTA. From these results, it was possible to establish the stoichiometry, thermal behavior, hydration water content, and the gaseous products released in the thermal decomposition steps, and suggest the type of metal-ligand coordination.

Thin films of metal-organic compounds and metal nanoparticle ...

Indian Academy of Sciences (India)

Optical limiting capability of the nanoparticle-embedded polymer film is demonstrated. Keywords. Polar crystal; uniaxial orientational order; thin film; second harmonic gen- eration; silver ... able content of metal nanoparticles would be of considerable value from an appli- ... polar chain and perpendicular to it [10].

Brazing technology of Ti alloy/stainless steel dissimilar metal joint at system integrated modular advanced reactor

International Nuclear Information System (INIS)

Kwon, Sang Chul; Kim, Sung Ho; Kim, Yong Wan; Kim, Jong In

2001-02-01

For the technoldogy development of brazing Ti alloy to stainless steel joints used at SMART, the status of brazing technology development, brazing processes, and the brazing technology of Ti alloy and stainless steel are reviewed. Because fusion welding process cannot be applied due to the formation of intermetallic compounds in the weld metal, brazing joint was selected at the design. The joint part is assembled with a thread composed with male part of Ti alloy tube and female part of stainless tube. The gap in the thread will be filled with brazing filler metal. However, brittle Ti-Fe intermetallic compounds are formed at the surface of stainless steel through the diffusion of Ti at the melt. Brazing conditions should be set-up to reduce the formation of intermetallic compounds. For that, 3 kinds of Ag filler metals were selected as the candidates and heating will be done with induction and electric furnaces. Through measuring of joint strength according to the control of pre- and post-braze treatment, heating rate and heating time, optimal brazing method will be fixed. To qualify the brazing procedure and performance and to check defects in final product, the inspection plan will be established according to the req2wuirements of AWS and ASME

Brazing technology of Ti alloy/stainless steel dissimilar metal joint at system integrated modular advanced reactor

Energy Technology Data Exchange (ETDEWEB)

Kwon, Sang Chul; Kim, Sung Ho; Kim, Yong Wan; Kim, Jong In

2001-02-01

For the technoldogy development of brazing Ti alloy to stainless steel joints used at SMART, the status of brazing technology development, brazing processes, and the brazing technology of Ti alloy and stainless steel are reviewed. Because fusion welding process cannot be applied due to the formation of intermetallic compounds in the weld metal, brazing joint was selected at the design. The joint part is assembled with a thread composed with male part of Ti alloy tube and female part of stainless tube. The gap in the thread will be filled with brazing filler metal. However, brittle Ti-Fe intermetallic compounds are formed at the surface of stainless steel through the diffusion of Ti at the melt. Brazing conditions should be set-up to reduce the formation of intermetallic compounds. For that, 3 kinds of Ag filler metals were selected as the candidates and heating will be done with induction and electric furnaces. Through measuring of joint strength according to the control of pre- and post-braze treatment, heating rate and heating time, optimal brazing method will be fixed. To qualify the brazing procedure and performance and to check defects in final product, the inspection plan will be established according to the req2wuirements of AWS and ASME.

Peroxotitanates for Biodelivery of Metals

Energy Technology Data Exchange (ETDEWEB)

Hobbs, David; Elvington, M.

2009-02-11

Metal-based drugs are largely undeveloped in pharmacology. One limiting factor is the systemic toxicity of metal-based compounds. A solid-phase, sequestratable delivery agent for local delivery of metals could reduce systemic toxicity, facilitating new drug development in this nascent area. Amorphous peroxotitanates (APT) are ion exchange materials with high affinity for several heavy metal ions, and have been proposed to deliver or sequester metal ions in biological contexts. In the current study, we tested a hypothesis that APT are able to deliver metals or metal compounds to cells. We exposed fibroblasts (L929) or monocytes (THP1) to metal-APT materials for 72 h in vitro, then measured cellular mitochondrial activity (SDH-MTT method) to assess the biological impact of the metal-APT materials vs. metals or APT alone. APT alone did not significantly affect cellular mitochondrial activity, but all metal-APT materials suppressed the mitochondrial activity of fibroblasts (by 30-65% of controls). The concentration of metal-APT materials required to suppress cellular mitochondrial activity was below that required for metals alone, suggesting that simple extracellular release of the metals from the metal-APT materials was not the primary mechanism of mitochondrial suppression. In contrast to fibroblasts, no metal-APT material had a measurable effect on THP1 monocyte mitochondrial activity, despite potent suppression by metals alone. This latter result suggested that 'biodelivery' by metal-APT materials may be cell type-specific. Therefore, it appears that APT are plausible solid phase delivery agents of metals or metal compounds to some types of cells for potential therapeutic effect.

Standard enthalpies of formation of selected Rh{sub 2}YZ Heusler compounds

Energy Technology Data Exchange (ETDEWEB)

Yin, Ming, E-mail: myin1@hawk.iit.edu; Nash, Philip

2015-11-25

The standard enthalpies of formation (Δ{sub f}H°) of selected ternary Rh-based Rh{sub 2}YZ (Y = Cu, Fe, Mn, Ni, Ru, Ti, V; Z = Al, Ga, In, Si, Ge, Sn) compounds were measured using high temperature direct reaction calorimetry. The measured standard enthalpies of formation (in kJ/mol of atoms) are, for the Heusler compound Rh{sub 2}MnSn (−40.1 ± 3.6), for the B2-structured compounds: Rh{sub 2}FeAl (−48.5 ± 2.9); Rh{sub 2}MnAl (−72.4 ± 2.7); Rh{sub 2}MnGa (−55.3 ± 2.0); Rh{sub 2}MnIn (−35.3 ± 1.9), for the tetragonal compounds: Rh{sub 2}FeSn (−28.9 ± 1.3); Rh{sub 2}TiAl (−97.6 ± 2.2); Rh{sub 2}TiGa (−79.0 ± 1.8); Rh{sub 2}TiSn (−74.7 ± 3.1). Values are compared with those from first principles calculations in published papers and the Open Quantum Materials Database (OQMD). Lattice parameters of these compounds are determined using X-ray diffraction analysis (XRD). Microstructures were characterized using scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). - Highlights: • Standard enthalpies of formation of Rh{sub 2}YZ were measured using a drop calorimeter. • Measured enthalpies agree with first principles data in general. • Lattice parameters and related phase relationships were consistent with literature data. • Rh{sub 2}TiSn of tI8 structure were reported for the first time.

Selective Se-for-S substitution in Cs-bearing uranyl compounds

Energy Technology Data Exchange (ETDEWEB)

Gurzhiy, Vladislav V., E-mail: vladgeo17@mail.ru [Department of Crystallography, St. Petersburg State University, University Emb. 7/9, 199034 St. Petersburg, Russia Federation (Russian Federation); Tyumentseva, Olga S.; Krivovichev, Sergey V. [Department of Crystallography, St. Petersburg State University, University Emb. 7/9, 199034 St. Petersburg, Russia Federation (Russian Federation); Tananaev, Ivan G. [Far Eastern Federal University, Suhanova st. 8, Vladivostok 690950 (Russian Federation)

2017-04-15

Phase formation in the mixed sulfate-selenate aqueous system of uranyl nitrate and cesium nitrate has been investigated. Two types of crystalline compounds have been obtained and characterized using a number of experimental (single crystal XRD, FTIR, SEM) and theoretical (information-based complexity calculations, topological analysis) techniques. No miscibility gaps have been observed for Cs{sub 2}[(UO{sub 2}){sub 2}(TO{sub 4}){sub 3}] (T= S, Se), which crystallizes in tetragonal system, P-42{sub 1}m, a =9.616(1)–9.856(2), c =8.105(1)–8.159(1) Å, V =749.6(2)–792.5(3) Å{sup 3}. Nine phases with variable amount of S and Se have been structurally characterized. The structures of the Cs{sub 2}[(UO{sub 2}){sub 2}(TO{sub 4}){sub 3}] (T= S, Se) compounds are based upon the [(UO{sub 2}){sub 2}(TO{sub 4}){sub 3}]{sup 2-} layers of corner-sharing uranyl pentagonal bipyramids and TO{sub 4} tetrahedra. The layers contain two types of tetrahedral sites: T1 (3-connected, i.e. having three O atoms shared by adjacent uranyl polyhedra) and T2 (4-connected). The Se-for-S substitution in tetrahedral sites is highly selective with smaller S{sup 6+} cation showing a strong preference for the more tightly bonded T2 site. Crystallization in the pure Se system starts with the formation of Cs{sub 2}[(UO{sub 2})(SeO{sub 4}){sub 2}(H{sub 2}O)](H{sub 2}O) crystals, its subsequent dissolution and formation of Cs{sub 2}[(UO{sub 2}){sub 2}(SeO{sub 4}){sub 3}]. The information-based structural complexity calculations for these two phases support the rule that more topologically complex structures form at the latest stages of crystallization. - Graphical abstract: Nine phases representing the Cs{sub 2}[(UO{sub 2}){sub 2}(TO{sub 4}){sub 3}] (T= S, Se) solid solution series with variable amount of S and Se have been prepared by isothermal evaporation from aqueous solutions and characterized using a number of experimental and theoretical techniques. No immiscibility is observed between the

Characterization and application of selective all-wet metallization of silicon

Science.gov (United States)

Uncuer, Muhammet; Koser, Hur

2012-01-01

We demonstrate selective, two-level metallization of silicon using electroless deposition of copper and gold. In this process, adhesion between the copper and silicon is improved with the formation of intermediary copper-silicide, and the gold layer protects copper from oxidation. The resistivity and residual stress of Au/Cu is 450 Ω nm (220 Ω nm annealed) and 56 MPa (tensile), respectively. These Au/Cu films allow a truly conformal and selective coating of high-aspect-ratio Si structures with good adhesion. We demonstrate the potential of these films in microswitches/relays, accelerometers and sensors by conformally coating the sidewalls of long (up to 1 mm in length), slender microbeams (5 µm × 5 µm) without inducing curvature.

Luminescent MOFs comprising mixed tritopic linkers and Cd(II)/Zn(II) nodes for selective detection of organic nitro compounds and iodine capture

Energy Technology Data Exchange (ETDEWEB)

Rachuri, Yadagiri; Bisht, Kamal Kumar [Analytical Discipline and Centralized Instrument Facility, CSIR–Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research, G. B. Marg, Bhavnagar 364002, Gujarat (India); Academy of Scientific and Innovative Research (AcSIR), CSIR–Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research, G. B. Marg, Bhavnagar 364002, Gujarat (India); Parmar, Bhavesh [Analytical Discipline and Centralized Instrument Facility, CSIR–Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research, G. B. Marg, Bhavnagar 364002, Gujarat (India); Suresh, Eringathodi, E-mail: esuresh@csmcri.org [Analytical Discipline and Centralized Instrument Facility, CSIR–Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research, G. B. Marg, Bhavnagar 364002, Gujarat (India); Academy of Scientific and Innovative Research (AcSIR), CSIR–Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research, G. B. Marg, Bhavnagar 364002, Gujarat (India)

2015-03-15

Two CPs ([Cd{sub 3}(BTC){sub 2}(TIB){sub 2}(H{sub 2}O){sub 4}].(H{sub 2}O){sub 2}){sub n} (1) and ([Zn{sub 3}(BTC){sub 2}(TIB){sub 2}].(H{sub 2}O){sub 6}){sub n} (2) composed of tripodal linkers BTC (1,3,5-benzenetricarboxylate) and TIB (1,3,5-tris(imidazol-1-ylmethyl)benzene) were synthesized via solvothermal route and structurally characterized. Single crystal structural analysis reveals 1 possesses a novel 3D framework structure, whereas 2 represents a previously established compound. Owing to the d{sup 10} configuration of metal nodes and robust 3D frameworks, 1 and 2 exhibit excellent fluorescence properties which have been exploited to sense organic nitro compounds in vapor phase. Compound 1 demonstrates selective sensing of nitromethane over structurally similar methanol with ca. 70 and 43% fluorescence quenching in case of former and later. Similarly, 58% fluorescence quenching was observed in case of nitrobenzene over the structurally resembling toluene for which 30% quenching was observed. Compound 2 did not show any preference for nitro compounds and exhibited comparable fluorescence quenching when exposed to the vapors of nitro or other geometrically resembling organic molecules. Furthermore, adsorption experiments revealed that 1 and 2 can uptake 2.74 and 14.14 wt% molecular iodine respectively in vapor phase which can be released in organic solvents such as hexane and acetonitrile. The maximal iodine uptake in case of 1 and 2 corresponds to 0.15 and 0.80 molecules of iodine per formula unit of respective frameworks. Comprehensive structural description, thermal stability and luminescence behavior for both CPs has also been presented. - Graphical abstract: Two 3D luminescent CPs comprising mixed tripodal ligands have been hydrothermally synthesized and structurally characterized. Iodine encapsulation capacity of synthesized CPs is evaluated and their fluorescence quenching in presence of small organic molecules is exploited for sensing of nitro

Macrocyclic receptor showing extremely high Sr(II)/Ca(II) and Pb(II)/Ca(II) selectivities with potential application in chelation treatment of metal intoxication.

Science.gov (United States)

Ferreirós-Martínez, Raquel; Esteban-Gómez, David; Tóth, Éva; de Blas, Andrés; Platas-Iglesias, Carlos; Rodríguez-Blas, Teresa

2011-04-18

Herein we report a detailed investigation of the complexation properties of the macrocyclic decadentate receptor N,N'-Bis[(6-carboxy-2-pyridil)methyl]-4,13-diaza-18-crown-6 (H(2)bp18c6) toward different divalent metal ions [Zn(II), Cd(II), Pb(II), Sr(II), and Ca(II)] in aqueous solution. We have found that this ligand is especially suited for the complexation of large metal ions such as Sr(II) and Pb(II), which results in very high Pb(II)/Ca(II) and Pb(II)/Zn(II) selectivities (in fact, higher than those found for ligands widely used for the treatment of lead poisoning such as ethylenediaminetetraacetic acid (edta)), as well as in the highest Sr(II)/Ca(II) selectivity reported so far. These results have been rationalized on the basis of the structure of the complexes. X-ray crystal diffraction, (1)H and (13)C NMR spectroscopy, as well as theoretical calculations at the density functional theory (B3LYP) level have been performed. Our results indicate that for large metal ions such as Pb(II) and Sr(II) the most stable conformation is Δ(δλδ)(δλδ), while for Ca(II) our calculations predict the Δ(λδλ)(λδλ) form being the most stable one. The selectivity that bp18c6(2-) shows for Sr(II) over Ca(II) can be attributed to a better fit between the large Sr(II) ions and the relatively large crown fragment of the ligand. The X-ray crystal structure of the Pb(II) complex shows that the Δ(δλδ)(δλδ) conformation observed in solution is also maintained in the solid state. The Pb(II) ion is endocyclically coordinated, being directly bound to the 10 donor atoms of the ligand. The bond distances to the donor atoms of the pendant arms (2.55-2.60 Å) are substantially shorter than those between the metal ion and the donor atoms of the crown moiety (2.92-3.04 Å). This is a typical situation observed for the so-called hemidirected compounds, in which the Pb(II) lone pair is stereochemically active. The X-ray structures of the Zn(II) and Cd(II) complexes show that

Metal based biologically active compounds: Design, synthesis, DNA binding and antidiabetic activity of 6-methyl-3-formyl chromone derived hydrazones and their metal (II) complexes.

Science.gov (United States)

Philip, Jessica Elizabeth; Shahid, Muhammad; Prathapachandra Kurup, M R; Velayudhan, Mohanan Puzhavoorparambil

2017-10-01

Two chromone hydrazone ligands HL 1 and HL 2 were synthesized and characterized by elemental analyses, IR, 1 H NMR & 13 C NMR, electronic absorption and mass spectra. The reactions of the chromone hydrazones with transition metals such as Ni, Cu, and Zn (II) salts of acetate afforded mononuclear metal complexes. Characterization and structure elucidation of the prepared chromone hydrazone metal (II) complexes were done by elemental, IR, electronic, EPR spectra and thermo gravimetric analyses as well as conductivity and magnetic susceptibility measurements. The spectroscopic data showed that the ligand acts as a mono basic bidentate with coordination sites are azomethine nitrogen and hydrazonic oxygen, and they exhibited distorted geometry. The biological studies involved antidiabetic activity i.e. enzyme inhibition of α-amylase and α-glucosidase, Calf Thymus - DNA (CT-DNA) interaction and molecular docking. Potential capacity of synthesized compounds to inhibit the α-amylase and α-glucosidase activity was assayed whereas DNA interaction studies were carried out with the help UV-Vis absorption titration and viscosity method. The docking studies of chromone hydrazones show that they are minor groove binders. Complexes were found to be good DNA - intercalates. Chromone hydrazones and its transition metal complexes have shown comparable antidiabetic activity with a standard drug acarbose. Copyright © 2017 Elsevier B.V. All rights reserved.

Alkylation and arylation of alkenes by transition metal complexes

International Nuclear Information System (INIS)

Volkova, L.G.; Levitin, I.Ya.; Vol'pin, M.E.

1975-01-01

In this paper are reviewed methods of alkylation and irylation of unsaturated compounds with complexes of transition metals (Rh, Pd). Analysis of alkylation and arylation of olefines with organic derivatives of transition metals, obtained as a result of exchange reactions between organic compounds of transition metals and salts of metals of the 8th group of the periodic system, allows a conclusion as to the wide possibilities of these reactions in the synthesis of various derivatives of unsaturated compounds. In all the reactions under consideration, intermediate formation of sigma-complexes is assumed. Also considered are alkylation and arylation of olefines with organic derivatives of halogens in the presence of compounds of metals of the 8th group of the periodic system, as well as arylation of olefines with aromatic compounds in the presence of salts of transition metals

Improvement of selective removal of heavy metals in cyanobacteria by NaOH treatment.

Science.gov (United States)

Nagase, Hiroyasu; Inthorn, Duangrat; Oda, Aiko; Nishimura, Jun; Kajiwara, Yumiko; Park, Myong-Oku; Hirata, Kazumasa; Miyamoto, Kazuhisa

2005-04-01

In the freshwater cyanobacterium, Tolypothrix tenuis, treatment with 0.1 M NaOH increased its Cd-selective adsorption ability in the presence of Ca(2+) or Mg(2+). The selective adsorption was also achieved by other alkaline treatments. Energy-distributed spectroscopy analysis revealed that Cd(2+) was found mainly on the surface of non-treated cells, whereas it was distributed throughout the cell after NaOH treatment. The alkaline treatment was effective in increasing the selective adsorption ability of the cyanobacterium for other bivalent heavy metals such as Cu(2+), Pb(2+) and Zn(2+). The treatment was also applicable to Anabaena variabilis and Microcystis aeruginosa, which are typical cyanobacteria causing algal blooms. The main binding site of Cd(2+) in NaOH-treated cells is assumed to be the carboxyl groups because the binding ability of the cells was diminished by the esterification of carboxyl groups. These results suggest that alkaline treatment of cyanobacteria is a useful technique for producing biosorbents having highly specific binding abilities for heavy metals.

Problems of selectivity in liquid-phase oxidation

Energy Technology Data Exchange (ETDEWEB)

Emanuel, N M

1978-07-01

Based on a kinetic analysis of a generalized scheme for radical-chain process and on published experimental results, factors determining the selectivities of various liquid-phase oxidations of organic compounds are examined, including the kinetic chain length, molecular and chain decomposition of products, and competing routes in the initiated oxidation or autoxidation of hydrocarbons to peroxides. Also discussed are selective inhibition of undesirable routes in chain reactions, e.g., styrene and acetaldehyde co-oxidation; activation of molecular oxygen by variable-valence metal compounds used as homogeneous catalysts; modeling of fermentative processes by oxidation of hydrocarbons in complex catalytic systems, e.g., hydroxylation of alkanes, epoxidation or carbonylation of olefins, or oxidation of alcohols and ketones to acids; and the mechanisms of heterogeneous catalysis in liquid-phase reactions, e.g., oxidation of alkylaromatic hydrocarbons to peroxides and co-oxidation of propylene and acetaldehyde.

Purification of uranium metal

International Nuclear Information System (INIS)

Suzuki, Kenji; Shikama, Tatsuo; Ochiai, Akira.

1993-01-01

We developed the system for purifying uranium metal and its metallic compounds and for growing highly pure uranium compounds to study their intrinsic physical properties. Uranium metal was zone refined under low contamination conditions as far as possible. The degree of the purity of uranium metal was examined by the conventional electrical resistivity measurement and by the chemical analysis using the inductive coupled plasma emission spectrometry (ICP). The results show that some metallic impurities evaporated by the r.f. heating and other usual metallic impurities moved to the end of a rod with a molten zone. Therefore, we conclude that the zone refining technique is much effective to the removal of metallic impurities and we obtained high purified uranium metal of 99.99% up with regarding to metallic impurities. The maximum residual resistivity ratio, the r.r.r., so far obtained was about 17-20. Using the purified uranium, we are attempting to grow a highly pure uranium-titanium single crystals. (author)

Selection of barrier metals for a waste package in tuff

International Nuclear Information System (INIS)

Russell, E.W.; McCright, R.D.; O'Neal, W.C.

1983-09-01

The Nevada Nuclear Waste Storage Investigation (NNWSI) project under the Civilian Radioactive Waste Management Program is planning a repository at Yucca Mountain at the Nevada Test Site for isolation of high-level nuclear waste. LLNL is developing designs for an engineered barrier system containing several barriers such as the waste form, a canister and/or an overpack, packing, and near field host rock. The selection of metal containment barriers is addressed. 13 references

First-row transition metal hydrogenation and hydrosilylation catalysts

Science.gov (United States)

Trovitch, Ryan J.; Mukhopadhyay, Tufan K.; Pal, Raja; Levin, Hagit Ben-Daat; Porter, Tyler M.; Ghosh, Chandrani

2017-07-18

Transition metal compounds, and specifically transition metal compounds having a tetradentate and/or pentadentate supporting ligand are described, together with methods for the preparation thereof and the use of such compounds as hydrogenation and/or hydrosilylation catalysts.

Halogen–Metal Exchange on Bromoheterocyclics with Substituents Containing an Acidic Proton via Formation of a Magnesium Intermediate

Directory of Open Access Journals (Sweden)

Qingqiang Tian

2017-11-01

Full Text Available A selective and practical bromine–metal exchange on bromoheterocyclics bearing substituents with an acidic proton under non-cryogenic conditions was developed by a simple modification of an existing protocol. Our protocol of using a combination of i-PrMgCl and n-BuLi has not only solved the problem of intermolecular quenching that often occurred when using alkyl lithium alone as the reagent for halogen–lithium exchange, but also offered a highly selective method for performing bromo–metal exchange on dibrominated arene compounds through chelation effect.

Antimicrobial resistance, heavy metal resistance and integron content in bacteria isolated from a South African tilapia aquaculture system.

Science.gov (United States)

Chenia, Hafizah Y; Jacobs, Anelet

2017-11-21

Antibacterial compounds and metals co-select for antimicrobial resistance when bacteria harbour resistance genes towards both types of compounds, facilitating the proliferation and evolution of antimicrobial and heavy metal resistance. Antimicrobial and heavy metal resistance indices of 42 Gram-negative bacteria from a tilapia aquaculture system were determined to identify possible correlations between these phenotypes. Agar dilution assays were carried out to determine susceptibility to cadmium, copper, lead, mercury, chromate and zinc, while susceptibility to 21 antimicrobial agents was investigated by disk diffusion assays. Presence of merA, the mercury resistance gene, was determined by dot-blot hybridizations and PCR. Association of mercury resistance with integrons and transposon Tn21 was also investigated by PCR. Isolates displayed a high frequency of antimicrobial (erythromycin: 100%; ampicillin: 85%; trimethoprim: 78%) and heavy metal (Zn2+: 95%; Cd2+: 91%) resistance. No correlation was established between heavy metal and multiple antibiotic resistance indices. Significant positive correlations were observed between heavy metal resistance profiles, indices, Cu2+ and Cr3+ resistance with erythromycin resistance. Significant positive correlations were observed between merA (24%)/Tn21 (24%) presence and heavy metal resistance profiles and indices; however, significant negative correlations were obtained between integron-associated qacE∆1 (43%) and sulI (26%) gene presence and heavy metal resistance indices. Heavy metal and antimicrobial agents co-select for resistance, with fish-associated, resistant bacteria demonstrating simultaneous heavy metal resistance. Thus, care should be taken when using anti-fouling heavy metals as feed additives in aquaculture facilities.

Guidelines for the determination of selected trace metals in aerosols and in wet precipitation

International Nuclear Information System (INIS)

1988-01-01

This publication describes sampling and analytical procedures suitable for the collection and analysis of representative samples of atmospheric aerosols and wet precipitation for selected trace metals. 11 refs, 2 tabs

Synthesis of heterocycles through transition-metal-catalyzed isomerization reactions

DEFF Research Database (Denmark)

Ishøy, Mette; Nielsen, Thomas Eiland

2014-01-01

of structurally complex and diverse heterocycles. In this Concept article, we attempt to cover this area of research through a selection of recent versatile examples. A sea of opportunities! Transition-metal-catalyzed isomerization of N- and O-allylic compounds provides a mild, selective and synthetically...... versatile method to form iminium and oxocarbenium ions. Given the number of reactions involving these highly electrophilic intermediates, this concept provides a sea of opportunities for heterocycle synthesis, (see scheme; Nu=nucleophile). © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim....

Data on heavy metals and selected anions in the Persian popular herbal distillates.

Science.gov (United States)

Keshtkar, Mozhgan; Dobaradaran, Sina; Soleimani, Farshid; Karbasdehi, Vahid Noroozi; Mohammadi, Mohammad Javad; Mirahmadi, Roghayeh; Ghasemi, Fatemeh Faraji

2016-09-01

In this data article, we determined the concentration levels of heavy metals including Pb, Co, Cd, Mn, Mg, Fe and Cu as well as selected anions including [Formula: see text] , [Formula: see text], [Formula: see text] and [Formula: see text] in the most used and popular herbal distillates in Iran. It is well known that heavy metals may pose a serious health hazard due to their bioaccumulation throughout the trophic chain ("Heavy metals (Cd, Cu, Ni and Pb) content in two fish species of Persian Gulf in Bushehr Port, Iran" (Dobaradaran et al., 2013) [1]; "Comparative investigation of heavy metal, trace, and macro element contents in commercially valuable fish species harvested off from the Persian Gulf" (Abadi et al., 2015) [2]) as well as some other environmental pollutions, "Assessment of sediment quality based on acid-volatile sulfide and simultaneously extracted metals in heavily industrialized area of Asaluyeh, Persian Gulf: concentrations, spatial distributions, and sediment bioavailability/toxicity" (Arfaeinia et al., 2016) [3]. The concentration levels of heavy metals and anions in herbal distillates samples were determined using flame atomic absorption spectrometry (FAAS, Varian AA240, Australia) and a spectrophotometer (M501 Single Beam Scanning UV/VIS, UK) respectively.

Determination of chlorine in nuclear-grade uranium compounds by ion-selective electrode

International Nuclear Information System (INIS)

Yang Chunqing; Liu Fuyun; Huang Dianfan.

1989-01-01

The determination of microamount chlorine in nuclear-grade uranium compounds is described. Chlorine is separated from uranium oxide pyrohydrolytically with stream of wet oxygen in a furnace at 800-900 deg C. Chlorine is volatilized as hydrochloric acid, which then is absorbed in a dilute alkaline solution and measured with chlorine selective electrode. This method covers the concentration range of 10-500 ppm chlorine in uranium oxide. The relative standard diviation is better than 10% and recovery of 85-108% has been reported

High-throughput screening of metal-porphyrin-like graphenes for selective capture of carbon dioxide

OpenAIRE

Hyeonhu Bae; Minwoo Park; Byungryul Jang; Yura Kang; Jinwoo Park; Hosik Lee; Haegeun Chung; ChiHye Chung; Suklyun Hong; Yongkyung Kwon; Boris I. Yakobson; Hoonkyung Lee

2016-01-01

Nanostructured materials, such as zeolites and metal-organic frameworks, have been considered to capture CO2. However, their application has been limited largely because they exhibit poor selectivity for flue gases and low capture capacity under low pressures. We perform a high-throughput screening for selective CO2 capture from flue gases by using first principles thermodynamics. We find that elements with empty d orbitals selectively attract CO2 from gaseous mixtures under low CO2 pressures...

Method and apparatus for selective capture of gas phase analytes using metal .beta.-diketonate polymers

Science.gov (United States)

Harvey, Scott D [Kennewick, WA

2011-06-21

A process and sensor device are disclosed that employ metal .beta.-diketonate polymers to selectively capture gas-phase explosives and weaponized chemical agents in a sampling area or volume. The metal .beta.-diketonate polymers can be applied to surfaces in various analytical formats for detection of: improvised explosive devices, unexploded ordinance, munitions hidden in cargo holds, explosives, and chemical weapons in public areas.

The effect of high-temperature treatment on the formation of nanoscale intermetallic compounds of transition metals in Al-Cu-Mn-Zr alloy

Science.gov (United States)

Monastyrska, Tetiana O.; Berezina, Alla L.; Labur, Tetiana M.; Molebny, Oleh A.; Kotko, Andrii V.

2018-02-01

The precipitation of intermetallic compounds of transition metals during aging of the Al-5.8%Cu-0.3%Mn-0.1%Zr alloy has been studied using DSC, resistometry, X-ray and transmission electron microscopy. In these age hardenable alloys, the nanoscale metastable Θ″ and Θ' phases of the Al2Cu compound are the main strengthening phases, which are formed at low temperature aging of T stresses, etc.) on the aging with the precipitation of strengthening phases has been investigated.

Composition of Trace Metals in Dust Samples Collected from Selected High Schools in Pretoria, South Africa

Directory of Open Access Journals (Sweden)

J. O. Olowoyo

2016-01-01

Full Text Available Potential health risks associated with trace metal pollution have necessitated the importance of monitoring their levels in the environment. The present study investigated the concentrations and compositions of trace metals in dust samples collected from classrooms and playing ground from the selected high schools In Pretoria. Schools were selected from Pretoria based on factors such as proximity to high traffic ways, industrial areas, and residential areas. Thirty-two dust samples were collected from inside and outside the classrooms, where learners often stay during recess period. The dust samples were analysed for trace metal concentrations using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS. The composition of the elements showed that the concentrations of Zn were more than all other elements except from one of the schools. There were significant differences in the concentrations of trace metals from the schools (p<0.05. Regular cleaning, proximity to busy road, and well maintained gardens seem to have positive effects on the concentrations of trace metals recorded from the classrooms dust. The result further revealed a positive correlation for elements such as Pb, Cu, Zn, Mn, and Sb, indicating that the dust might have a common source.

On metal-insulator transition in cubic fullerides

Science.gov (United States)

Iwahara, Naoya; Chibotaru, Liviu

The interplay between degenerate orbital and electron correlation is a key to characterize the electronic phases in, for example, transition metal compounds and alkali-doped fullerides. Besides, the degenerate orbital couples to spin and lattice degrees of freedom ,giving rise to exotic phenomena. Here, we develop the self-consistent Gutzwiller approach for the simultaneous treatment of the Jahn-Teller effect and electron correlation, and apply the methodology to reveal the nature of the ground electronic state of fullerides. For small Coulomb repulsion on site U, the fulleride is quasi degenerate correlated metal. With increase of U, we found the quantum phase transition from the metallic phase to JT split phase. In the latter, the Mott transition (MT) mainly develops in the half-filled subband, whereas the empty and the completely filled subbands are almost uninvolved. Therefore, we can qualify the metal-insulator transition in fullerides as an orbital selective MT induced by JT effect.

Transition-metal chlorides as conversion cathode materials for Li-ion batteries

International Nuclear Information System (INIS)

Li Ting; Chen, Zhong X.; Cao, Yu L.; Ai, Xin P.; Yang, Han X.

2012-01-01

Insoluble AgCl and soluble CuCl 2 were selected and investigated as model compounds of transition-metal chlorides for electrochemical conversion cathode materials. The experimental results demonstrated that the AgCl nanocrystals can convert reversibly to metallic Ag with nearly full utilization of its one-electron redox capacity (187 mAh g −1 ). Similarly, the CuCl 2 -filled mesoporous carbon can realize a reversible two-electron transfer reaction, giving a very high reversible capacity of 466 mAh g −1 after 20 cycles. These data imply that the metal chlorides can undergo complete electrochemical conversion utilizing their full oxidation states for electrical energy storage as previously reported metal fluorides, possibly being used as high capacity cathode materials for Li-ion batteries.

Characterisation of hydrocarbonaceous overlayers important in metal-catalysed selective hydrogenation reactions

Energy Technology Data Exchange (ETDEWEB)

Lennon, David; Warringham, Robbie [School of Chemistry, Joseph Black Building, University of Glasgow, Glasgow G12 8QQ (United Kingdom); Guidi, Tatiana [ISIS Facility, STFC Rutherford Appleton Laboratory, Chilton, Didcot, Oxfordshire OX11 0QX (United Kingdom); Parker, Stewart F., E-mail: stewart.parker@stfc.ac.uk [ISIS Facility, STFC Rutherford Appleton Laboratory, Chilton, Didcot, Oxfordshire OX11 0QX (United Kingdom)

2013-12-12

Highlights: • Inelastic neutron scattering spectroscopy of a commercial dehydrogenation catalyst. • The overlayer present on the catalyst is predominantly aliphatic. • A population of strongly hydrogen bonded hydroxyls is also present. - Abstract: The hydrogenation of alkynes to alkenes over supported metal catalysts is an important industrial process and it has been shown that hydrocarbonaceous overlayers are important in controlling selectivity profiles of metal-catalysed hydrogenation reactions. As a model system, we have selected propyne hydrogenation over a commercial Pd(5%)/Al{sub 2}O{sub 3} catalyst. Inelastic neutron scattering studies show that the C–H stretching mode ranges from 2850 to 3063 cm{sup −1}, indicating the mostly aliphatic nature of the overlayer and this is supported by the quantification of the carbon and hydrogen on the surface. There is also a population of strongly hydrogen-bonded hydroxyls, their presence would indicate that the overlayer probably contains some oxygen functionality. There is little evidence for any olefinic or aromatic species. This is distinctly different from the hydrogen-poor overlayers that are deposited on Ni/Al{sub 2}O{sub 3} catalysts during methane reforming.

Nucleation of recrystallization at selected sites in deformed fcc metals

DEFF Research Database (Denmark)

Xu, Chaoling

The objective of this thesis is to explore nucleation of recrystallization at selected sites in selected face-centered-cubic (FCC) metals, namely cold rolled columnar-grained nickel and high purity aluminum further deformed by indenting. Various techniques, including, optical microscopy, electron...... backscattered diffraction (EBSD), electron channeling contrast (ECC) and synchrotron X-ray technique, differential-aperture X-ray microscopy (DAXM), were used to characterize the microstructures, to explore nucleation sites, orientation relationships between nuclei and deformed microstructures, and nucleation...... mechanisms. In the cold rolled nickel samples, the preference of triple junctions (TJs) and grain boundaries (GBs) as nucleation sites is observed. The majorities of the nuclei have the same orientations as the surrounding matrix or are twin-related to a surrounding deformed grain. Only a few nuclei...

Development of a thermodynamic data base for selected heavy metals

International Nuclear Information System (INIS)

Hageman, Sven; Scharge, Tina; Willms, Thomas

2015-07-01

The report on the development of a thermodynamic data base for selected heavy metals covers the description of experimental methods, the thermodynamic model for chromate, the thermodynamic model for dichromate, the thermodynamic model for manganese (II), the thermodynamic model for cobalt, the thermodynamic model for nickel, the thermodynamic model for copper (I), the thermodynamic model for copper(II), the thermodynamic model for mercury (0) and mercury (I), the thermodynamic model for mercury (III), the thermodynamic model for arsenate.

Biologically active compounds of semi-metals

Czech Academy of Sciences Publication Activity Database

Řezanka, Tomáš; Sigler, Karel

2008-01-01

Roč. 69, č. 3 (2008), s. 585-606 ISSN 0031-9422 Institutional research plan: CEZ:AV0Z50200510 Keywords : semi-metals * boron * silicon Subject RIV: CE - Biochemistry Impact factor: 2.946, year: 2008

The effects of pH and concentration on heavy metal speciation and mobility, and its relation to heavy metal hyperaccumulation and distribution in selected native Australian flora

International Nuclear Information System (INIS)

Menon, D.D.; McPhail, D.C.; Hallam, N.

2000-01-01

Full text: The purpose of this research is to establish a clearer understanding of the relations that exist between heavy metal activity, speciation, bioavailability and their uptake and spatial distribution into plants. A combination of experimental modeling and pot trials using toxic heavy metals (cadmium, lead, mercury, copper, chromium and zinc) will be carried out. In the experiments, selected native Australian flora (Eucalyptus, Acacia, Atriplex) adapted to adverse environmental conditions will be used. Varying external factors such as pH, and metal concentration altered the composition of heavy metal speciation in the soil solution. Mathematical and geochemical (PHREEQC) models were used to vary these factors and emulate the conditions under which experimentation will be taking place. These variations help determine the possible heavy metal speciation that would occur in both soil and hydroponic based experiments under given conditions. The rhizosphere, soil solution and the plant material will be analysed by Inductively Coupled Plasma Mass Spectroscopy (ICPMS). Proton Ion X-ray Emission (PIXE) and Secondary Ion Mass spectrometry will help ascertain the distribution, concentration of heavy metal taken up into plant tissues. Information derived from these data will be used to determine and understand how varying such environmental conditions and hence heavy metal speciation affect their bioavailability in the medium, and how their acceptance, accumulation and storage within the selected flora. Preliminary experimentation showed that, for lead and cadmium, the variation in soil solution pH affected the quantity of heavy metal accumulated into selected native Australian flora. ICP-MS analysis of plants subjected to a known soil solution spiked with 200 μmol of lead and cadmium showed that the quantities of lead and cadmium accumulated into plant sections (roots, stems and leaves) varied in the selected woody species. A. heteroclita, A. saligna, and A

Laser-induced selective metallization of polypropylene doped with multiwall carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Ratautas, Karolis, E-mail: karolis.ratautas@ftmc.lt [Center for Physical Sciences and Technology, Savanoriu Ave. 231, Vilnius LT-02300 (Lithuania); Gedvilas, Mindaugas; Stankevičiene, Ina; Jagminienė, Aldona; Norkus, Eugenijus [Center for Physical Sciences and Technology, Savanoriu Ave. 231, Vilnius LT-02300 (Lithuania); Pira, Nello Li [Centro Ricerche Fiat, Strada Torino 50, Orbassano 10043 (Italy); Sinopoli, Stefano [BioAge Srl, Via Dei Glicini 25, Lamezia Terme 88046 (Italy); Račiukaitis, Gediminas [Center for Physical Sciences and Technology, Savanoriu Ave. 231, Vilnius LT-02300 (Lithuania)

2017-08-01

Highlights: • PP doped with multiwall CNT can be activated with ns laser for electroless plating. • Developed material is cheap decision for MID applications. • Activation mechanism was preliminary proposed. • Demo for automotive application has been manufactured. - Abstract: Moulded interconnect devices (MID) offer the material, weight and cost saving by integration electronic circuits directly into polymeric components used in automotive and other consumer products. Lasers are used to write circuits directly by modifying the surface of polymers followed by an electroless metal plating. A new composite material – the polypropylene doped with multiwall carbon nanotubes was developed for the laser-induced selective metallization. Mechanism of surface activation by laser irradiation was investigated in details utilising pico- and nanoseconds lasers. Deposition of copper was performed in the autocatalytic electroless plating bath. The laser-activated polymer surfaces have been studied using the Raman spectroscopy and scanning electron microscope (SEM). Microscopic images revealed that surface becomes active only after its melting by a laser. Alterations in the Raman spectra of the D and G bands indicated the clustering of carbon additives in the composite material. Optimal laser parameters for the surface activation were found by measuring a sheet resistance of the finally metal-plated samples. A spatially selective copper plating was achieved with the smallest conductor line width of 22 μm at the laser scanning speed of 3 m/s and the pulse repetition rate of 100 kHz. Finally, the technique was validated by making functional electronic circuits by this MID approach.

Laser-induced selective metallization of polypropylene doped with multiwall carbon nanotubes

International Nuclear Information System (INIS)

Ratautas, Karolis; Gedvilas, Mindaugas; Stankevičiene, Ina; Jagminienė, Aldona; Norkus, Eugenijus; Pira, Nello Li; Sinopoli, Stefano; Račiukaitis, Gediminas

2017-01-01

Highlights: • PP doped with multiwall CNT can be activated with ns laser for electroless plating. • Developed material is cheap decision for MID applications. • Activation mechanism was preliminary proposed. • Demo for automotive application has been manufactured. - Abstract: Moulded interconnect devices (MID) offer the material, weight and cost saving by integration electronic circuits directly into polymeric components used in automotive and other consumer products. Lasers are used to write circuits directly by modifying the surface of polymers followed by an electroless metal plating. A new composite material – the polypropylene doped with multiwall carbon nanotubes was developed for the laser-induced selective metallization. Mechanism of surface activation by laser irradiation was investigated in details utilising pico- and nanoseconds lasers. Deposition of copper was performed in the autocatalytic electroless plating bath. The laser-activated polymer surfaces have been studied using the Raman spectroscopy and scanning electron microscope (SEM). Microscopic images revealed that surface becomes active only after its melting by a laser. Alterations in the Raman spectra of the D and G bands indicated the clustering of carbon additives in the composite material. Optimal laser parameters for the surface activation were found by measuring a sheet resistance of the finally metal-plated samples. A spatially selective copper plating was achieved with the smallest conductor line width of 22 μm at the laser scanning speed of 3 m/s and the pulse repetition rate of 100 kHz. Finally, the technique was validated by making functional electronic circuits by this MID approach.

Interplay of metals and bromine with dioxin-related compounds concentrated in e-waste open burning soil from Agbogbloshie in Accra, Ghana

International Nuclear Information System (INIS)

Fujimori, Takashi; Itai, Takaaki; Goto, Akitoshi; Asante, Kwadwo A.; Otsuka, Masanari; Takahashi, Shin; Tanabe, Shinsuke

2016-01-01

Open burning of electronic waste (e-waste) releases various metals and organohalogen compounds in the environment. Here we investigated the interplay of metals (Cu, Pb, Zn, Fe, Co, and Sr) and bromine (Br) in the formation of dioxin-related compounds (DRCs), including polychlorinated dibenzo-p-dioxins/furans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs), as well as non-regulated DRCs such as polybrominated dibenzo-p-dioxins/furans (PBDD/Fs) and their monobrominated PCDD/Fs in soils sampled from open burning e-waste sites at Agbogbloshie in Accra, Ghana. The predominant DRCs were PBDFs, PCDFs, PCDDs, and DL-PCBs. Statistical analyzes, X-ray absorption spectroscopy, and the PCDF/PCDD ratio suggested possible formation paths of PCDD/Fs and DL-PCBs by catalytic behaviors of copper chlorides (CuCl, CuCl_2, and Cu_2(OH)_3Cl) and thermal breakdown of polyvinyl chloride. Predominant formation of brominated furans may be derived from electron transfer from intermediates of PBDE to copper, Cu(II) → Cu(I). Lead chloride also contributed to generate DRCs and may become highly bioaccessible through the open burning of e-waste. The main zinc species (ZnCl_2 and ZnS) suggested a possible relationship to generate DRCs and specific zinc source such as tire burning. Cu, Pb, Zn, and Br contained in various e-wastes, wires/cables, plastics, and tires strongly influenced generation of many DRCs. - Highlights: • Extremely high DRCs were detected from an open burning soil of e-waste. • Predominant DRCs were PBDFs, PCDFs, PCDDs, and DL-PCBs. • Some metals shows good correlation to DRCs by PCA and cluster analysis. • Speciation of Cu, Pb, Zn in residual soil were successfully measured by XAFS. • Electron transfer via Cu(II) → Cu(I) can be important for DRCs formation. - Metals speciation in residual soil after open burning of e-waste may act as a catalyst for formation of dioxin-related compounds.

Catalytic olefin polymerization with early transition metal compounds

NARCIS (Netherlands)

Eshuis, Johan Jan Willem

1991-01-01

The catalysis of organic reactions by soluble metal complexes has become a major tool in synthesis, both in the laboratory and in the chemical industry. Processes catalyzed by transition metal complexes include carbonylation, olefin polymerization, olefin addition, olefin oxidation and alkane and

Use of response surface methodology to evaluate the effect of metal ions (Ca2+, Ni2+, Mn2+, Cu2+) on production of antifungal compounds by Paenibacillus polymyxa.

Science.gov (United States)

Raza, Waseem; Hongsheng, Wu; Qirong, Shen

2010-03-01

The effects of four metal ions (Ca(2+), Ni(2+), Mn(2+) and Cu(2+)) were evaluated on growth and production of antifungal compounds by Paenibacillus polymyxa SQR-21 and a quadratic predictive model was developed using response surface methodology (RSM). The results revealed, Mn(2+) and Ni(2+) showed most positive synergistic interactive affect on production of antifungal compounds followed by the positive interactive synergistic affect of Cu(2+) and Ni(2+) and then Mn(2+) and Cu(2+). While the interactive effect of Ca(2+) with all other three metals inhibited the production of antifungal compounds. The Mn(2+) (P=0.0384), Ni(2+) (P=0.0004) and Cu(2+) (P=0.0117) significantly affected the production of antifungal compounds while the effect of Ca(2+) (P=0.1851) was less significant. The maximum growth (OD(600)=1.55) was obtained at 500 (0), 125 (0), 100 (-2) and 37.5 (0) microM levels and the maximum size of inhibition zone (31 mm) was measured at 400 (-1), 150 (1), 400 (1) and 25 microM (-1) levels of Ca(2+), Mn(2+), Ni(2+) and Cu(2+), respectively. The RSM model provided an easy and effective way to determine the interactive effect of metal ions on production of antifungal compounds by P. polymyxa SQR-21 so that optimum media recipes can be developed to produce maximum amounts of antifungal compounds under laboratory and commercial fermentation conditions. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

A Potential Waste to be Selected as Media for Metal and Nutrient Removal

Science.gov (United States)

Zayadi, N.; Othman, N.; Hamdan, R.

2016-07-01

This study describes the potential of application of cassava peel, banana peel, coconut shell, and coconut coir to be selected as metal removal while limestone and steel slag for nutrient removal. The media were characterized by X-Ray Fluorescence (XRF), Fourier Transform Infrared (FTIR), Field Emission Scanning Electron Microscopy-Energy Dispersive X-Ray (FESEM-EDX), and X-Ray Powder Diffraction (XRD). The results of XRF analysis medias show the present of calcium oxide, CaO which confirm the high efficiency in adsorbing metal ions and nutrient which is in agreement with the result of XRD. The characteristics of medias by FTIR analysis also confirmed the involvement of alcohol, carboxylic, alkanes, amines and ethers which play important role to reduce ions while FESEM-EDX indicates the porous structures of study medias. The characterization analysis highlight that cassava peel and steel slag were selected as a potential media in this study.

LIQUID METAL COMPOSITIONS CONTAINING URANIUM

Science.gov (United States)

Teitel, R.J.

1959-04-21

Liquid metal compositions containing a solid uranium compound dispersed therein is described. Uranium combines with tin to form the intermetallic compound USn/sub 3/. It has been found that this compound may be incorporated into a liquid bath containing bismuth and lead-bismuth components, if a relatively small percentage of tin is also included in the bath. The composition has a low thermal neutron cross section which makes it suitable for use in a liquid metal fueled nuclear reactor.

Experimental formation enthalpies for intermetallic phases and other inorganic compounds

Science.gov (United States)

Kim, George; Meschel, S. V.; Nash, Philip; Chen, Wei

2017-01-01

The standard enthalpy of formation of a compound is the energy associated with the reaction to form the compound from its component elements. The standard enthalpy of formation is a fundamental thermodynamic property that determines its phase stability, which can be coupled with other thermodynamic data to calculate phase diagrams. Calorimetry provides the only direct method by which the standard enthalpy of formation is experimentally measured. However, the measurement is often a time and energy intensive process. We present a dataset of enthalpies of formation measured by high-temperature calorimetry. The phases measured in this dataset include intermetallic compounds with transition metal and rare-earth elements, metal borides, metal carbides, and metallic silicides. These measurements were collected from over 50 years of calorimetric experiments. The dataset contains 1,276 entries on experimental enthalpy of formation values and structural information. Most of the entries are for binary compounds but ternary and quaternary compounds are being added as they become available. The dataset also contains predictions of enthalpy of formation from first-principles calculations for comparison. PMID:29064466

Resistance of Bacteria Isolated from Otamiri River to Heavy Metals and Some Selected Antibiotics

OpenAIRE

I.C. Mgbemena; J.C. Nnokwe; L.A. Adjeroh; N.N. Onyemekara

2012-01-01

This study is aimed at determining the resistance of bacteria to heavy metals and some antibiotics. The ability of aquatic bacteria isolates from Otamiri River at Ihiagwa in Owerri North, Imo State to tolerate or resist the presence of certain selected heavy metals: Pb+, Zn2+ and Fe2+ and some antibiotics was investigated. Identification tests for the bacteria isolates from Otamiri River revealed them to belong to the genera Pseudomonas, Aeromonas, Bacillus, Escherichia, Micrococcus and Prote...

High-Pressure Thermodynamic Properties of f-electron Metals, Transition Metal Oxides, and Half-Metallic Magnets

International Nuclear Information System (INIS)

Richard T. Scalettar; Warren E. Pickett

2005-01-01

This project involves research into the thermodynamic properties of f-electron metals, transition metal oxides, and half-metallic magnets at high pressure. These materials are ones in which the changing importance of electron-electron interactions as the distance between atoms is varied can tune the system through phase transitions from localized to delocalized electrons, from screened to unscreened magnetic moments, and from normal metal to one in which only a single spin specie can conduct. Three main thrusts are being pursued: (1) Mott transitions in transition metal oxides, (2) magnetism in half-metallic compounds, and (3) large volume-collapse transitions in f-band metals

High-Pressure Thermodynamic Properties of f-electron Metals, Transition Metal Oxides, and Half-Metallic Magnets

Energy Technology Data Exchange (ETDEWEB)

Scalettar, Richard T.; Pickett, Warren E.

2004-07-01

This project involves research into the thermodynamic properties of f-electron metals, transition metal oxides, and half-metallic magnets at high pressure. These materials are ones in which the changing importance of electron-electron interactions as the distance between atoms is varied can tune the system through phase transitions from localized to delocalized electrons, from screened to unscreened magnetic moments, and from normal metal to one in which only a single spin specie can conduct. Three main thrusts are being pursued: (1) Mott transitions in transition metal oxides, (2) magnetism in half-metallic compounds, and (3) large volume-collapse transitions in f-band metals.

High-Pressure Thermodynamic Properties of f-electron Metals, Transition Metal Oxides, and Half-Metallic Magnets

Energy Technology Data Exchange (ETDEWEB)

Richard T. Scalettar; Warren E. Pickett

2005-08-02

This project involves research into the thermodynamic properties of f-electron metals, transition metal oxides, and half-metallic magnets at high pressure. These materials are ones in which the changing importance of electron-electron interactions as the distance between atoms is varied can tune the system through phase transitions from localized to delocalized electrons, from screened to unscreened magnetic moments, and from normal metal to one in which only a single spin specie can conduct. Three main thrusts are being pursued: (i) Mott transitions in transition metal oxides, (ii) magnetism in half-metallic compounds, and (iii) large volume-collapse transitions in f-band metals.

A study on heterogeneous photocatalytic degradation of various organic compounds using N-Tio2 under Uv-light irradiation

Science.gov (United States)

Srujana, Dhegam; Sailu, Chinta

2018-04-01

The aim of this work is to determine the photocatalytic degradation of mixture of four selected organic compounds are Congo Red (CR), Methylene Blue (MB), Diclofenaec (DC), 4-Chlorophenol (4-CP) have been subjected to Photo catalytic degradation by Ultraviolet (λ=254nm) radiation in presence of Nitrogen-doped Titanium dioxide (N-TiO2) catalyst. This paper focused on the enhancement of photo catalysis by modification of TiO2 employing non-metal ion (Nitrogen) doping. Experiments are conducted with a mixture of equal proportions of organic compounds (CR, MB, DC, and 4-CP) with combined concentrations of 10, 20, 30, 40 and 50 mg/l in water in a batch reactor in presence of N-TiO2catalyst with UV light (λ=254nm). The rate of degradation of each compound is determined by using spectrophotometer. The kinetics of degradation of the selected organic compounds is followed first order rate.

Performance of metal compound on thermolysis and electrolysis on sugar industries waste water treatment: COD and color removal with sludge analysis (batch-experiment)

Science.gov (United States)

Sahu, Omprakash

2017-10-01

The sugar cane industry is one of the most water demanding industries. Sugar industries consume and generate excess amount of water. The generated water contains organic compounds, which would cause pollution. The aim of this research work is to study the effectiveness of metal compound for treatment of sugar industry waste water by thermolysis and electrolysis process. The result shows ferrous metal catalyst shows 80 and 85 % chemical oxygen demand and color removal at pH 6, optimum mass loading 4 kg/m3, treatment temperature 85 °C and treatment time 9 h. When ferrous material was used as electrode, maximum 81 % chemical oxygen demand and 84 % color removal at pH 6, current density 156 Am-2, treatment time 120 min and anode consumption 0.7 g for 1.5 L wastewater were obtained.

Melting-decontamination method for radioactive contaminated metals

International Nuclear Information System (INIS)

Uda, Tatsuhiko; Tsuchiya, Hiroyuki; Miura, Noboru; Iba, Hajime.

1985-01-01

Purpose: To eliminate uranium components remaining in metals even after the uranium-contaminated metals are melted. Method: Metal wastes contaminated with actinide element or its compound as nuclear fuel substance are melted in a crucible. Molten metals are fallen through a filter disposed at the bottom of the crucible into another receiving crucible. Uranium compounds are still left in the molten metal fallen in the receiving crucible. The residual uranium compounds are concentrated by utilizing the principle of the zone-refining process. That is, a displaceable local-heating heater is disposed to the receiving crucible, by which metals once solidified in the receiving crucible is again heated locally to transfer from solid to molten phase in a quasi-equibilized manner. In this way, by eliminating the end of the metal rod at which the uranium is segregated, the contaminating coefficient can be improved. (Ikeda, J.)

PLASTICITY OF SELECTED METALLIC MATERIALS IN DYNAMIC DEFORMATION CONDITIONS

Directory of Open Access Journals (Sweden)

Jacek PAWLICKI

2014-06-01

Full Text Available Characteristics of a modernized flywheel machine has been presented in the paper. The laboratory stand enables to perform dynamic tensile tests and impact bending with a linear velocity of the enforcing element in the range of 5÷40 m/s. A new data acquisition system, based on the tensometric sensors, allows for significant qualitative improvement of registered signals. Some preliminary dynamic forming tests were performed for the selected group of metallic materials. Subsequent microstructural examinations and identification of the fracture type enabled to describe a correlation between strain rate, strain and microstructure.

Selection of barrier metals for a waste package in tuff

International Nuclear Information System (INIS)

Russell, E.W.; McCright, R.D.; O'Neal, W.C.

1983-10-01

The Nevada Nuclear Waste Storage Investigations (NNWSI) project under the Civilian Radioactive Waste Management Program is planning a repository at Yucca Mountain at the Nevada Test Site for isolation of high-level nuclear waste. Lawrence Livermore National Laboratory is developing designs for an engineered barrier system containing several barriers such as the waste form, a canister and/or an overpack, packing, and near field host rock. In this paper we address the selection of metal containment barriers. 13 references, 4 tables

POLYMER COMPOSITE FILMS WITH SIZE-SELECTED METAL NANOPARTICLES FABRICATED BY CLUSTER BEAM TECHNIQUE

DEFF Research Database (Denmark)

Ceynowa, F. A.; Chirumamilla, Manohar; Popok, Vladimir

2017-01-01

Formation of polymer films with size-selected silver and copper nanoparticles (NPs) is studied. Polymers are prepared by spin coating while NPs are fabricated and deposited utilizing a magnetron sputtering cluster apparatus. The particle embedding into the films is provided by thermal annealing...... after the deposition. The degree of immersion can be controlled by the annealing temperature and time. Together with control of cluster coverage the described approach represents an efficient method for the synthesis of thin polymer composite layers with either partially or fully embedded metal NPs....... Combining electron beam lithography, cluster beam deposition and thermal annealing allows to form ordered arrays of metal NPs on polymer films. Plasticity and flexibility of polymer host and specific properties added by coinage metal NPs open a way for different applications of such composite materials...

A three-dimensional metal–organic framework for selective sensing of nitroaromatic compounds

Directory of Open Access Journals (Sweden)

Dan Tian

2014-12-01

Full Text Available A 3D metal–organic framework [NH2(CH32][Cd6(L4(DMF6(HCOO](DMF = N,N-dimethylformamide (1 has been synthesized using a tripodal ligand H3L (2,4,6-tris[1-(3-carboxylphenoxyylmethyl]mesitylene. The obtained complex exhibits a 3D framework containing hexanuclear {Cd6} building units formed by two trinuclear {Cd3} clusters that are connected via HCOO− anions. For complex 1, the participation of the fluorescent ligand H3L not only gives rise to a strong photoluminescence emission as expected, but more interestingly, that ligand originated characteristic band could be quenched selectively by nitrobenzene with a low detection limit, showing its potential as a highly sensitive and selective sensor for nitrobenzene. Based on an electron transfer quenching mechanism, the fluorescence sensing ability of 1 is also applicable for other electron-deficient nitroaromatic compounds with high selectivity and sensitivity, i.e., 1,4-dinitrobenzene, 1,3-dinitrobenzene, 2,4-dinitrotoluene, and 4-nitrotoluene, suggesting 1 a promising fluorescence sensor for detecting and recognizing the same kind of chemicals.

Structural, electronic, magnetic, half-metallic, mechanical, and thermodynamic properties of the quaternary Heusler compound FeCrRuSi: A first-principles study.

Science.gov (United States)

Wang, Xiaotian; Khachai, Houari; Khenata, Rabah; Yuan, Hongkuan; Wang, Liying; Wang, Wenhong; Bouhemadou, Abdelmadjid; Hao, Liyu; Dai, Xuefang; Guo, Ruikang; Liu, Guodong; Cheng, Zhenxiang

2017-11-23

In this paper, we have investigated the structural, electronic, magnetic, half-metallic, mechanical, and thermodynamic properties of the equiatomic quaternary Heusler (EQH) compound FeCrRuSi using the density functional theory (DFT) and the quasi-harmonic Debye model. Our results reveal that FeCrRuSi is a half-metallic material (HMM) with a total magnetic moment of 2.0 μ B in agreement with the well-known Slater-Pauling rule M t  = Z t  - 24. Furthermore, the origin of the half-metallic band gap in FeCrRuSi is well studied through a schematic diagram of the possible d-d hybridization between Fe, Cr and Ru elements. The half-metallic behavior of FeCrRuSi can be maintained in a relatively wide range of variations of the lattice constant (5.5-5.8 Å) under uniform strain and the c/a ratio (0.96-1.05) under tetragonal distortion. The calculated phonon dispersion, cohesive and formation energies, and mechanical properties reveal that FeCrRuSi is stable with an EQH structure. Importantly, the compound of interest has been prepared and is found to exist in an EQH type structure with the presence of some B2 disorder. Moreover, the thermodynamic properties, such as the thermal expansion coefficient α, the heat capacity C V , the Grüneisen constant γ, and the Debye temperature Θ D are calculated.

Thin film Heusler compounds manganese nickel gallium

Science.gov (United States)

Jenkins, Catherine Ann

Multiferroic Heusler compounds Mn3--xNi xGa (x=0,1,2) have a tetragonal unit cell that can variously be used for magneto-mechanically coupled shape memory ( x=1,2) and spin-mechanical applications (x=0). The first fabrication of fully epitaxial thin films of these and electronically related compounds by sputtering is discussed. Traditional and custom lab characterization of the magnetic and temperature driven multiferroic behavior is augmented by more detailed synchrotron-based high energy photoemission spectroscopic techniques to describe the atomic and electronic structure. Integration of the MnNi2Ga magnetic shape memory compound in microwave patch antennas and active free-standing structures represents a fraction of the available and promising applications for these compounds. Prototype magnetic tunnel junctions are demonstrated by Mn3Ga electrodes with perpendicular anisotropy for spin torque transfer memory structures. The main body of the work concentrates on the definition and exploration of the material series Mn3--xNi xGa (x=0,1,2) and the relevant multiferroic phenomena exhibited as a function of preparation and external stimuli. Engineering results on each x=0,1,2 are presented with device prototypes where relevant. In the appendices the process of the materials design undertaken with the goal of developing new ternary intermetallics with enhanced properties is presented with a full exploration of the road from band structure calculations to device implementation. Cobalt based compounds in single crystal and nanoparticle form are fabricated with an eye to developing the production methods for new cobalt- and iron-based magnetic shape memory compounds for device applications in different forms. Mn2CoSn, a compound isolectronic and with similar atomic ordering to Mn2NiGa is experimentally determined to be a nearly half-metallic ferromagnet in contrast to the metallic ferrimagnetism in the parent compound. High energy photoemission spectroscopy is shown to

Effect of Metals, Metalloids and Metallic Nanoparticles on Microalgae Growth and Industrial Product Biosynthesis: A Review.

Science.gov (United States)

Miazek, Krystian; Iwanek, Waldemar; Remacle, Claire; Richel, Aurore; Goffin, Dorothee

2015-10-09

Microalgae are a source of numerous compounds that can be used in many branches of industry. Synthesis of such compounds in microalgal cells can be amplified under stress conditions. Exposure to various metals can be one of methods applied to induce cell stress and synthesis of target products in microalgae cultures. In this review, the potential of producing diverse biocompounds (pigments, lipids, exopolymers, peptides, phytohormones, arsenoorganics, nanoparticles) from microalgae cultures upon exposure to various metals, is evaluated. Additionally, different methods to alter microalgae response towards metals and metal stress are described. Finally, possibilities to sustain high growth rates and productivity of microalgal cultures in the presence of metals are discussed.

Ground state properties and thermoelectric behavior of Ru{sub 2}VZ (Z=Si, ge, sn) half-metallic ferromagnetic full-Heusler compounds

Energy Technology Data Exchange (ETDEWEB)

Yalcin, Battal Gazi

2016-06-15

The ground state properties namely structural, mechanical, electronic and magnetic properties and thermoelectric behavior of Ru{sub 2}VZ (Z=Si, Ge and Sn) half-metallic ferromagnetic full-Heusler compounds are systematically investigated. These compounds are ferromagnetic and crystallize in the Heusler type L2{sub 1} structure (prototype: Cu{sub 2}MnAl, Fm-3m 225). This result is confirmed for Ru{sub 2}VSi and Ru{sub 2}VSn by experimental work reported by Yin and Nash using high temperature direct reaction calorimetry. The studied materials are half-metallic ferromagnets with a narrow direct band gap in the minority spin channel that amounts to 31 meV, 66 meV and 14 meV for Ru{sub 2}VSi, Ru{sub 2}VGe, and Ru{sub 2}VSn, respectively. The total spin magnetic moment (M{sub tot}) of the considered compounds satisfies a Slater–Pauling type rule for localized magnetic moment systems (M{sub tot}=(N{sub V}−24)µ{sub B}), where N{sub V}=25 is the number of valence electrons in the primitive cell. The Curie temperature within the random phase approximation (RPA) is found to be 23 K, 126 K and 447 K for Ru{sub 2}VSi, Ru{sub 2}VGe and Ru{sub 2}VSn, respectively. Semi-classical Boltzmann transport theories have been used to obtain thermoelectric constants, such as Seebeck coefficient (S), electrical (σ/τ) and thermal conductivity (κ/τ), power factor (PF) and the Pauli magnetic susceptibility (χ). ZT{sub MAX} values of 0.016 (350 K), 0.033 (380 K) and 0.063 (315 K) are achieved for Ru{sub 2}VSi, Ru{sub 2}VGe and Ru{sub 2}VSn, respectively. It is expected that the obtained results might be a trigger in future experimentally interest in this type of full-Heusler compounds. - Graphical abstract: Temperature dependence of figure of merit for Ru{sub 2}VZ (Z=Si, Ge, and Sn) compounds. - Highlights: • The ground state and thermoelectric properties are reported for the first time. • Ru{sub 2}VZ are found to be a half-metallic ferromagnetic full Heusler compound. • The

Hybrid compounds of Keggin polyoxotungstate with transition metal ion as the central atom. Synthesis, structure and properties

Science.gov (United States)

Li, Xiao-Min; Chen, Ya-Guang; Shi, Tian

2016-02-01

The compounds (Hbipy)2[Co(bipy)2(H2O)4]2(CoW12O40)·2bipy·7H2O (1) and [Ni2(Hbipy)2(bipy)(H2O)4(H2W12O40)]·5H2O (2) (bipy = 4,4-bipyridine) were synthesized hydrothermally and characterized by elemental analysis, IR spectroscopy, TG analyses, solid ultraviolet diffuse spectroscopy and single crystal X-ray diffraction method. In 1 the complex ions, [Co(bipy)2(H2O)4]2+, construct a supramolecular layer through π-π stacking interaction. The heteropolyanions with central Co atom and supramolecular layers are linked by hydrogen bonds. In 2 a 2D structure is formed from metatungstate anions and binuclear Ni-bipy complexes through the coordination of metatungstate anions and bipy to Ni ions. Between the layers and bipyridine molecules are the hydrogen bond interactions. The formation of 1 and 2 shows that the solution acidity and metal ions influence greatly the structure of the compounds. Solid ultraviolet diffusion results indicate that the compounds 1 and 2 are potential semiconductor materials. In 1 and 2 there exists a weak antiferromagnetic interaction.

Selective extraction of metals from products of mine acidic water treatment

International Nuclear Information System (INIS)

Andreeva, N.N.; Romanchuk, S.A.; Voronin, N.N.; Demidov, V.D.; Pasynkova, T.A.; Manuilova, O.A.; Ivanova, N.V.

1989-01-01

A study was made on possibility of processing of foam products prepared during flotation purification of mine acidic waters for the purpose of selective extraction of non-ferrous (Co, Ni) and rare earth elements (REE) and their separation from the basic macrocomponent of waters-iron. Optimal conditions of selective metal extraction from foam flotation products are the following: T=333 K, pH=3.0-3.5, ratio of solid and liquid phase - 1:4-1:7, duration of sulfuric acid leaching - 30 min. Rare earth extraction under such conditions equals 87.6-93.0%. The degree of valuable component concentration equals ∼ 10. Rare earths are separated from iron by extraction methods

THERMOPLASTIC MATRIX SELECTION FOR FIBRE METAL LAMINATE USING FUZZY VIKOR AND ENTROPY MEASURE FOR OBJECTIVE WEIGHTING

Directory of Open Access Journals (Sweden)

N. M. ISHAK

2017-10-01

Full Text Available The purpose of this study is to define the suitable thermoplastic matrix for fibre metal laminate for automotive front hood utilisation. To achieve the accurate and reliable results, the decision making process involved subjective and objective weighting where the combination of Fuzzy VIKOR and entropy method have been applied. Fuzzy VIKOR is used for ranking purpose and entropy method is used to determine the objective weighting. The result shows that polypropylene is the best thermoplastic matrix for fibre metal laminate by satisfying two compromise solutions with validation using least VIKOR index value scored 0.00, compared to low density polyethylene, high density polyethylene and polystyrene. Through a combination of Fuzzy VIKOR and entropy, it is proved that this method gives a higher degree of confidence to the decision maker especially for fibre metal laminate thermoplastic matrix selection due to its systematic and scientific selection method involving MCDM.

Synthesis, characterization and investigation of thermoelectric properties of selected metal borides; Synthese, Charakterisierung und Untersuchung thermoelektrischer Eigenschaften ausgewaehlter Metallboride

Energy Technology Data Exchange (ETDEWEB)

Stober, Frederick

2012-06-04

The present work deals with the high-temperature thermoelectric properties of transition metal [eg V, Cr, Mn, Ni, Cu] and lanthanide [e.g. Sc, Y, Gd, Er, Dy]-borides. In particular, intercalation compounds of beta-rhombohedral boron, compounds of the type MB{sub 66}, dodecaborides and hexaborides were examined. In the case of intercalation compounds of beta-rhombohedral boron it was found that the incorporation of metals such as Sc, Mn or Cu result in favorable thermoelectric properties. The reason is most likely the preferred occupation of the metal position M2 instead of M4. Composites, for example, DyB{sub 66}-DyB{sub 12} show high electrical conductivities, high Seebeck effects at high temperatures due to the presence of DyB{sub 12} and low thermal conductivities as a result of the DyB{sub 66} matrix. At 1100K the composite DyB{sub 66}-DyB{sub 12} shows a ZT value of 0.55, thus exceeding the ZT of boron carbide (B{sub 13}C{sub 2}) at this temperature which is considered the best p-type boride material. A composite of ErB{sub 12}-ErB{sub 4}-ErB{sub 2} has negative Seebeck coefficients and shows a ZT value of 0.5 at 840K. Furthermore, the structure of tetragonal Scandiumdodecaboride ScB{sub 12} was solved on the basis of synchrotron data from a crystalline powder, after it has been debated for decades but never fully resolved.

Formation of biaxial texture in metal films by selective ion beam etching

Energy Technology Data Exchange (ETDEWEB)

Park, S.J. [Department of Materials Science and Engineering, University of Florida, 106 Rhines Hall, P.O. Box 116400, Gainesville, FL 32611 (United States); Norton, D.P. [Department of Materials Science and Engineering, University of Florida, 106 Rhines Hall, P.O. Box 116400, Gainesville, FL 32611 (United States)]. E-mail: dnort@mse.ufl.edu; Selvamanickam, Venkat [IGC-SuperPower, LLC, 450 Duane Avenue, Schenectady, NY 12304 (United States)

2006-05-15

The formation of in-plane texture via ion bombardment of uniaxially textured metal films was investigated. In particular, selective grain Ar ion beam etching of uniaxially textured (0 0 1) Ni was used to achieve in-plane aligned Ni grains. Unlike conventional ion beam assisted deposition, the ion beam irradiates the uniaxially textured film surface with no impinging deposition flux. The initial uniaxial texture is established via surface energy minimization with no ion irradiation. Within this sequential texturing method, in-plane grain alignment is driven by selective etching and grain overgrowth. Biaxial texture was achieved for ion beam irradiation at elevated temperature.

Formation of biaxial texture in metal films by selective ion beam etching

International Nuclear Information System (INIS)

Park, S.J.; Norton, D.P.; Selvamanickam, Venkat

2006-01-01

The formation of in-plane texture via ion bombardment of uniaxially textured metal films was investigated. In particular, selective grain Ar ion beam etching of uniaxially textured (0 0 1) Ni was used to achieve in-plane aligned Ni grains. Unlike conventional ion beam assisted deposition, the ion beam irradiates the uniaxially textured film surface with no impinging deposition flux. The initial uniaxial texture is established via surface energy minimization with no ion irradiation. Within this sequential texturing method, in-plane grain alignment is driven by selective etching and grain overgrowth. Biaxial texture was achieved for ion beam irradiation at elevated temperature

Luminescent Lanthanide Metal Organic Frameworks for cis-Selective Isoprene Polymerization Catalysis

Directory of Open Access Journals (Sweden)

Samantha Russell

2015-11-01

Full Text Available In this study, we are combining two areas of chemistry; solid-state coordination polymers (or Metal-Organic Framework—MOF and polymerization catalysis. MOF compounds combining two sets of different lanthanide elements (Nd3+, Eu3+/Tb3+ were used for that purpose: the use of neodymium was required due to its well-known catalytic properties in dienes polymerization. A second lanthanide, europium or terbium, was included in the MOF structure with the aim to provide luminescent properties. Several lanthanides-based MOF meeting these criteria were prepared according to different approaches, and they were further used as catalysts for the polymerization of isoprene. Stereoregular cis-polyisoprene was received, which in some cases exhibited luminescent properties in the UV-visible range.

Average and local structure of selected metal deuterides

Energy Technology Data Exchange (ETDEWEB)

Soerby, Magnus H.

2005-07-01

The main topic of this thesis is improved understanding of site preference and mutual interactions of deuterium (D) atoms in selected metallic metal deuterides. The work was partly motivated by reports of abnormally short D-D distances in RENiInD1.33 compounds (RE = rear-earth element; D-D {upsilon} square root 1.6 Aa) which show that the so-called Switendick criterion that demands a D-D separation of at least 2 Aa, is not a universal rule. The work is experimental and heavily based on scattering measurements using x-rays (lab and synchrotron) and neutrons. In order to enhance data quality, deuterium is almost exclusively used instead of natural hydrogen in sample preparations. The data-analyses are in some cases taken beyond ''conventional'' analysis of the Bragg scattering, as the diffuse scattering contains important information on D-D distances in disordered deuterides (Paper 3 and 4). A considerable part of this work is devoted to determination of the crystal structure of saturated Zr2Ni deuteride, Zr2NiD-4.8. The structure remained unsolved when only a few months remained of the scholarship. The route to the correct structure was found in the last moment. In Chapter II this winding road towards the structure determination is described; an interesting exercise in how to cope with triclinic superstructures of metal hydrides. The solution emerged by combining data from synchrotron radiation powder x-ray diffraction (SR-PXD), powder neutron diffraction (PND) and electron diffraction (ED). The triclinic crystal structure, described in space group P1 , is fully ordered with composition Zr4Ni2D9 (Zr2NiD4.5). The unit cell is doubled as compared to lower Zr2Ni deuterides due to a deuterium superstructure: asuper = a, bsuper = b - c, csuper = b + c. The deviation from higher symmetry is very small. The metal lattice is pseudo-I-centred tetragonal and the deuterium lattice is pseudo-C-centred monoclinic. The deuterium site preference in Zr2Ni

Average and local structure of selected metal deuterides

International Nuclear Information System (INIS)

Soerby, Magnus H.

2004-01-01

The main topic of this thesis is improved understanding of site preference and mutual interactions of deuterium (D) atoms in selected metallic metal deuterides. The work was partly motivated by reports of abnormally short D-D distances in RENiInD1.33 compounds (RE = rear-earth element; D-D Υ square root 1.6 Aa) which show that the so-called Switendick criterion that demands a D-D separation of at least 2 Aa, is not a universal rule. The work is experimental and heavily based on scattering measurements using x-rays (lab and synchrotron) and neutrons. In order to enhance data quality, deuterium is almost exclusively used instead of natural hydrogen in sample preparations. The data-analyses are in some cases taken beyond ''conventional'' analysis of the Bragg scattering, as the diffuse scattering contains important information on D-D distances in disordered deuterides (Paper 3 and 4). A considerable part of this work is devoted to determination of the crystal structure of saturated Zr2Ni deuteride, Zr2NiD-4.8. The structure remained unsolved when only a few months remained of the scholarship. The route to the correct structure was found in the last moment. In Chapter II this winding road towards the structure determination is described; an interesting exercise in how to cope with triclinic superstructures of metal hydrides. The solution emerged by combining data from synchrotron radiation powder x-ray diffraction (SR-PXD), powder neutron diffraction (PND) and electron diffraction (ED). The triclinic crystal structure, described in space group P1 , is fully ordered with composition Zr4Ni2D9 (Zr2NiD4.5). The unit cell is doubled as compared to lower Zr2Ni deuterides due to a deuterium superstructure: asuper = a, bsuper = b - c, csuper = b + c. The deviation from higher symmetry is very small. The metal lattice is pseudo-I-centred tetragonal and the deuterium lattice is pseudo-C-centred monoclinic. The deuterium site preference in Zr2Ni deuterides at 1 bar D2 and