77 FR 51469 - Change of Address for Merit Systems Protection Board

Science.gov (United States)

2012-08-24

... Protection Board. DATES: Effective August 24, 2012. FOR FURTHER INFORMATION CONTACT: Thomas J. Schlageter, Assistant Legal Counsel, (202) 663-4668, or Danielle J. Hayot, Senior Attorney, (202) 663-4695, Office of...

Thermoelectric System in Different Thermal and Electrical Configurations: Its Impact in the Figure of Merit

Directory of Open Access Journals (Sweden)

Alexander Vargas-Almeida

2013-05-01

Full Text Available In this work, we analyze different configurations of a thermoelectric system (TES composed of three thermoelectric generators (TEGs. We present the following considerations: (a TES thermally and electrically connected in series (SC; (b TES thermally and electrically connected in parallel (PSC; and (c parallel thermally and series electrical connection (SSC. We assume that the parameters of the TEGs are temperature-independent. The systems are characterized by three parameters, as it has been showed in recent investigations, namely, its internal electrical resistance, R, thermal conductance under open electrical circuit condition, K, and Seebeck coefficient α. We derive the equivalent parameters for each of the configurations considered here and calculate the Figure of Merit Z for the equivalent system. We show the impact of the configuration of the system on Z, and we suggest optimum configuration. In order to justify the effectiveness of the equivalent Figure of Merit, the corresponding efficiency has been calculated for each configuration.

Discharge Onset Voltage Prediction for a Gas-Insulated System Via the Figure-of-Merit Concept

DEFF Research Database (Denmark)

Crichton, George C; Vibholm, Svend

1987-01-01

The accuracy of discharge onset prediction via thefigur figure-of-merit concept for a strongly electronegative gas is examined. A coaxial system is employed, for which the inner electrode possesses a surface roughness of Ra=35 ¿m. With SF6 as the insulating medium a reference discharge......-onset characteristic is obtained for gas pressures up to 0.8 MPa. From a knowledge of this onset characteristic, the direct calculation of discharge onset voltages in other strongly electronegative gases is undertaken by utilizing thefigur figure-of-merit concept. For gas pressures in the range O.02...

Hazard rate for a two-channel protective system subject to a high demand rate

International Nuclear Information System (INIS)

Oliveira, L.F.; Youngblood, R.; Melo, P.F.F.

1989-01-01

A basic figure of merit associated with a protective system for an industrial plant is the number of accidents expected to occur in the plant within a given period of time, with the system installed. By definition, in a plant equipped with a protective system, an accident can only happen if an initiating event (a demand) occurs while the protective system is unavailable, that is, while it is in one of its possible failed states. This means that the hazard rate or accident frequency depends on the demand rate and on the unavailability of the protective systems. It has long been recognized that the demand rate influences the unavailability of the protective system, and practical expressions incorporating that effect have been developed for single-channel (Lees, 1982) and multi-channel (Kumamoto and Henley 1978) protective systems. The effect has also been incorporated into a Markovian treatment of a plant protection system (Papazoglou and Cho, 1985). In a previous paper (Oliveira and Netto, 1987) a Markovian approach was used to derive analytical expressions for the evaluation of the plant hazard rate for a single-channel protective system, properly accounting for the effects of the demand and the repair rates. In this paper the authors present an extension of that model to the case of a plant equipped with a two-channel protective system

Merit Pay and the Music Teacher

Science.gov (United States)

Elpus, Kenneth

2011-01-01

Current proponents of education reform are at present seeking to fundamentally change the system of teacher compensation by eliminating the traditional single salary schedule and instituting a merit pay system that directly links teacher pay to student achievement. To date, the scholarly literature in music education has been silent on the subject…

Employee Reactions to Merit Pay: Cognitive Approach and Social Approach

Science.gov (United States)

Wang, Yingchun

2010-01-01

The dissertation aims to tackle one of the most pressing questions facing the merit pay system researchers and practitioners: Why do merit pay raises have such a small effect on employees' satisfaction, commitment and job performance? My approach to the study of this question is to develop explanatory frameworks from two perspectives: cognitive…

Teachers' Perceptions of Merit Pay

Science.gov (United States)

Jackson, Vanessa; Langheinrich, Cornelia; Loth, Dan

2012-01-01

The purpose of the study is to show the various perceptions teachers have on merit pay. This research was designed to examine the perceptions and attitudes of teachers towards the idea of performance based pay. This topic has been an ongoing battle within school systems since the 1800s. The participants in this study were teachers from the state…

Value-Added Merit Pay.

Science.gov (United States)

Twomey, Daniel F.

The purpose of merit pay is to reward employees for their accomplishments and motivate them to continue improving. Critics of merit pay say the increased extrinsic motivation that it prompts is more than offset by the decrease in intrinsic motivation. Supporters of performance-based pay claim several benefits of the practice. This study addressed…

Chess players' fame versus their merit.

Science.gov (United States)

Simkin, M V; Roychowdhury, V P

2015-12-12

We investigate a pool of international chess title holders born between 1901 and 1943. Using Elo ratings, we compute for every player his expected score in a game with a randomly selected player from the pool. We use this figure as the player's merit. We measure players' fame as the number of Google hits. The correlation between fame and merit is 0.38. At the same time, the correlation between the logarithm of fame and merit is 0.61. This suggests that fame grows exponentially with merit.

Pedagogical Merit Review of Animal Use for Education in Canada.

Directory of Open Access Journals (Sweden)

Marc T Avey

Full Text Available There are two components to the review of animal based protocols in Canada: review for the merit of the study itself, and review of the ethical acceptability of the work. Despite the perceived importance for the quality assurance these reviews provide; there are few studies of the peer-based merit review system for animal-based protocols for research and education. Institutional animal care committees (ACCs generally rely on the external peer review of scientific merit for animal-based research. In contrast, peer review for animal based teaching/training is dependent on the review of pedagogical merit carried out by the ACC itself or another committee within the institution. The objective of this study was to evaluate the views of ACC members about current practices and policies as well as alternate policies for the review of animal based teaching/training. We conducted a national web-based survey of ACC members with both quantitative and qualitative response options. Responses from 167 ACC members indicated broad concerns about administrative burden despite strong support for both the current and alternate policies. Participants' comments focused mostly on the merit review process (54% relative to the efficiency (21%, impact (13%, and other (12% aspects of evaluation. Approximately half (49% of the comments were classified into emergent themes that focused on some type of burden: burden from additional pedagogical merit review (16%, a limited need for the review (12%, and a lack of resources (expertise 11%; people/money 10%. Participants indicated that the current system for pedagogical merit review is effective (60%; but most also indicated that there was at least some challenge (86% with the current peer review process. There was broad support for additional guidance on the justification, criteria, types of animal use, and objectives of pedagogical merit review. Participants also supported the ethical review and application of the Three Rs in

2017 MERIT Exercise close to completion!

CERN Multimedia

Staff Association

2017-01-01

The 2017 MERIT Guidelines, approved by the Standing Concertation Committee (SCC), concern various processes and procedures, among which those for the annual exercise (or MERIT interview), promotions, and changes of benchmark job. The processes for “annual exercise” and “promotions” – “changes of benchmark job” have been programmed for two periods: from 1st December 2016 to 15 June 2017: MERIT interviews, evaluation, performance qualification and payment with effect as of the salary of May; from 3 April 2017 to 1st July 2017: promotions and changes of benchmark job. 2017 MERIT Interviews The results of the MERIT interviews have been announced to staff members, most of whom saw their salary increase. Only persons who are not eligible and those with “Insufficient” performance qualification did not receive a raise. Same goes for performance payments – the staff members whose performance was qualified as &ldq...

Merit-Based Incentive Payment System (MIPS): Harsh Choices For Interventional Pain Management Physicians.

Science.gov (United States)

Manchikanti, Laxmaiah; Helm Ii, Standiford; Benyamin, Ramsin M; Hirsch, Joshua A

2016-01-01

The Merit-based Incentive Payment System (MIPS) was created by the Medicare Access and CHIP Reauthorization Act of 2015 (MACRA) to improve the health of all Americans by providing incentives and policies to improve patient health outcomes. MIPS combines 3 existing programs, Meaningful Use (MU), now called Advancing Care Information (ACI), contributing 25% of the composite score; Physician Quality Reporting System (PQRS), changed to Quality, contributing 50% of the composite score; and Value-based Payment (VBP) system to Resource Use or cost, contributing 10% of the composite score. Additionally, Clinical Practice Improvement Activities (CPIA), contributing 15% of the composite score, create multiple strategic goals to design incentives that drive movement toward delivery system reform principles with inclusion of Advanced Alternative Payment Models (APMs). Under the present proposal, the Centers for Medicare and Medicaid Services (CMS) has estimated approximately 30,000 to 90,000 providers from a total of over 761,000 providers will be exempt from MIPS. About 87% of solo practitioners and 70% of practitioners in groups of less than 10 will be subjected to negative payments or penalties ranging from 4% to 9%. In addition, MIPS also will affect a provider's reputation by making performance measures accessible to consumers and third-party physician rating Web sites.The MIPS composite performance scoring method, at least in theory, utilizes weights for each performance category, exceptional performance factors to earn bonuses, and incorporates the special circumstances of small practices.In conclusion, MIPS has the potential to affect practitioners negatively. Interventional Pain Medicine practitioners must understand the various MIPS measures and how they might participate in order to secure a brighter future. Medicare Access and CHIP Reauthorization Act of 2015, merit-based incentive payment system, quality performance measures, resource use, clinical practice

Figures of merit for surface plasmon waveguides

Science.gov (United States)

Berini, Pierre

2006-12-01

Three figures of merit are proposed as quality measures for surface plasmon waveguides. They are defined as benefit-to-cost ratios where the benefit is confinement and the cost is attenuation. Three different ways of measuring confinement are considered, leading to three figures of merit. One of the figures of merit is connected to the quality factor. The figures of merit were then used to assess and compare the wavelength response of hree popular 1-D surface plasmon waveguides: the single metal-dielectric interface, the metal slab bounded by dielectric and the dielectric slab bounded by metal. Closed form expressions are given for the figures of merit of the single metal-dielectric interface.

Merits and Demerits of Food Additives

OpenAIRE

YANG, Xuening; ZHAN, Yong

2014-01-01

Food additive is a double-edged sword. It has merits and demerits. Food additives have such merits as improving sensory properties of foods, preventing deterioration and extending the shelf life, increasing varieties of foods, enhancing convenience of foods, facilitating food processing, and satisfying other demands. However, excessive and illegal use of food additives will exert adverse influence on food security. Therefore, it is required to take proper measures to bring merits of food addi...

Merit exponents and control area diagrams in materials selection

International Nuclear Information System (INIS)

Zander, Johan; Sandstroem, Rolf

2011-01-01

Highlights: → Merit exponents are introduced to generalise the merit indices commonly used in materials selection. → The merit exponents can rank materials in general design situations. → To allow identification of the active merit exponent(s), control area diagrams are used. → Principles for generating the control area diagrams are presented. -- Abstract: Merit indices play a fundamental role in materials selection, since they enable ranking of materials. However, the conventional formulation of merit indices is associated with severe limitations. They are dependent on the explicit solution of the variables in the equations for the constraints from the design criteria. Furthermore, it is not always easy to determine which the controlling merit index is. To enable the ranking of materials in more general design cases, merit exponents are introduced as generalisations of the merit indices. Procedures are presented for how to compute the merit exponents numerically without having to solve equations algebraically. Merit exponents (and indices) are only valid in a certain range of property values. To simplify the identification of the controlling merit exponent, it is suggested that so called control area diagrams are used. These diagrams consist of a number of domains, each showing the active constraints and the controlling merit exponent. It is shown that the merit exponents play a crucial role when the control area diagram (CAD) is set up. The principles in the paper are developed for mechanically loaded components and are illustrated for engineering beams with two or three geometric variables.

Merits and Demerits of Food Additives

Institute of Scientific and Technical Information of China (English)

Xuening; YANG; Yong; ZHAN

2014-01-01

Food additive is a double-edged sword. It has merits and demerits. Food additives have such merits as improving sensory properties of foods,preventing deterioration and extending the shelf life,increasing varieties of foods,enhancing convenience of foods,facilitating food processing,and satisfying other demands. However,excessive and illegal use of food additives will exert adverse influence on food security.Therefore,it is required to take proper measures to bring merits of food additives into full play,and get rid of their demerits.

The Merit-based Incentive Payment System (MIPS): A Primer for Otolaryngologists.

Science.gov (United States)

Rathi, Vinay K; Naunheim, Matthew R; Varvares, Mark A; Holmes, Kenneth; Gagliano, Nancy; Hartnick, Christopher J

2018-05-01

Following passage of the 2015 Medicare Access and CHIP Reauthorization Act, most clinicians caring for Medicare Part B patients were required to participate in a new value-based reimbursement system known as the Merit-based Incentive Payment System (MIPS) beginning in 2017. The MIPS adjusts payment rates to providers based on a composite score of performance across 4 categories: quality, advancing care information, clinical practice improvement activities, and resource use. However, factors such as practice size, setting, informational capabilities, and patient population may pose challenges as otolaryngologists endeavor to adapt to this broad-reaching payment reform. Given potential barriers to adoption, otolaryngologists should be aware of several important initiatives to help optimize their performance, including advocacy efforts by the American Academy of Otolaryngology-Head and Neck Surgery, the development of otolaryngology-specific MIPS quality measures, and the launch of a Centers for Medicare & Medicaid Services-qualified otolaryngology clinical data registry to facilitate reporting.

Measuring Student Growth within a Merit-Pay Evaluation System: Perceived Effects on Music Teacher Motivation Career Commitment

Science.gov (United States)

Munroe, Angela

2017-01-01

In this experimental study, music teachers from a large school district were randomly assigned to one of two hypothetical conditions reflecting different methods for measuring student growth under a merit pay compensation system. In Scenario A, half of a teacher's effectiveness rating was based on student standardized test scores in reading,…

Improving Teaching Effectiveness: Merit Pay vs. Organizational Culture.

Science.gov (United States)

Bushardt, Stephen C.; Fowler, Aubrey R.

1987-01-01

Identifies four conditions which cause merit pay systems to fail to increase teacher performance: lack of skills, the poor timing of rewards, an inability to measure performance; and competing reinforcers. Explains why organizational culture is a more effective mediator of rewards. (SD)

Merit-Based Scholarships and Student Effort

Science.gov (United States)

Hernandez-Julian, Rey

2010-01-01

Twenty-one states offer merit scholarships that require students to maintain a minimum grade point average (GPA). Using a comprehensive administrative database from Clemson University, this study estimates the relationship between the incentives created by a South Carolina merit scholarship (LIFE) and students' academic performance. I hypothesize…

Enhancement of the thermoelectric figure of merit in a quantum dot due to external ac field

Energy Technology Data Exchange (ETDEWEB)

Chen, Qiao, E-mail: cqhy1127@yahoo.com.cn [Department of Maths and Physics, Hunan Institute of Engineering, Xiangtan 411104 (China); Wang, Zhi-yong, E-mail: wzyong@cqut.edu.cn [School of Optoelectronic Information, Chongqing University of Technology, Chongqing 400054 (China); Xie, Zhong-Xiang [Department of Mathematics and Physics, Hunan Institute of Technology, Hengyang 421002 (China)

2013-08-15

We investigate the figure of merit of a quantum dot (QD) system irradiated with an external microwave filed by nonequilibrium Green's function (NGF) technique. Results show that the frequency of microwave field influence the figure of merit ZT significantly. At low temperature, a sharp peak can be observed in the figure of merit ZT as the frequency of ac field increases. As the frequency varies, several zero points and resonant peaks emerge in the figure of merit ZT. By adjusting the frequency of the microwave field, we can obtain high ZT. The figure of merit ZT increases with the decreasing of linewidth function Γ. In addition, Wiedemann–Franz law does not hold, particularly in the low frequency region due to multi-photon emission and absorption. Some novel thermoelectric properties are also found in two-level QD system.

The relationship between genetic merit for yield and live weight, condition score, and energy balance of spring calving Holstein Friesian dairy cows on grass based systems of milk production

NARCIS (Netherlands)

Buckley, F.; Dillon, P.; Rath, M.; Veerkamp, R.F.

2000-01-01

The objectives of this study were to estimate the effects of genetic merit for milk yield on energy balance, DM intake (DMI), and fertility for cows managed on three different grass-based feeding systems and to estimate possible interactions between genetic merit and feeding system. Individual

DOE Hydrogen Program: 2005 Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

Chalk, S. G.

2005-09-01

This report summarizes comments from the Peer Review Panel at the FY 2005 DOE Hydrogen Program Annual Merit Review, held on May 23-26, 2005, in Arlington, Virginia. The projects evaluated support the Department of Energy and President Bush's Hydrogen Initiative. The results of this merit review and peer evaluation are major inputs used by DOE to make funding decisions. Project areas include hydrogen production and delivery; hydrogen storage; fuel cells; technology validation; safety, codes and standards; education; and systems analysis.

DOE Hydrogen Program: 2006 Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

Milliken, J.

2006-09-01

This report summarizes comments from the Peer Review Panel at the FY 2006 DOE Hydrogen Program Annual Merit Review, held on May 16-19, 2006, in Arlington, Virginia. The projects evaluated support the Department of Energy and President Bush's Hydrogen Initiative. The results of this merit review and peer evaluation are major inputs used by DOE to make funding decisions. Project areas include hydrogen production and delivery; hydrogen storage; fuel cells; technology validation; safety, codes and standards; education; and systems analysis.

Protected Areas

Data.gov (United States)

Kansas Data Access and Support Center — This dataset shows the boundaries of properties in Kansas in public or institutional ownership that contain ecological resources that merit some level of protection....

Cybersecurity Figure of Merit

Science.gov (United States)

2016-04-30

Space and Naval Warfare Systems Command The Cybersecurity Challenge in Acquisition Sonia Kaestner, Adjunct Professor, McDonough School of Business ...qÜáêíÉÉåíÜ=^ååì~ä= ^Åèìáëáíáçå=oÉëÉ~êÅÜ= póãéçëáìã= tÉÇåÉëÇ~ó=pÉëëáçåë= sçäìãÉ=f= = Cybersecurity Figure of Merit CAPT Brian Erickson, USN, SPAWAR...the Acquisition Research Program of the Graduate School of Business & Public Policy at the Naval Postgraduate School. To request defense acquisition

DOE Hydrogen Program: 2007 Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

Milliken, J.

2007-09-01

This report summarizes comments from the Peer Review Panel at the FY 2007 DOE Hydrogen Program Annual Merit Review, held on May 14-18, 2007, in Washington, D.C. The projects evaluated support the Department of Energy and President Bush's Hydrogen Initiative. The results of this merit review and peer evaluation are major inputs used by DOE to make funding decisions. Project areas include hydrogen production and delivery; hydrogen storage; fuel cells; technology validation; safety, codes and standards; education; and systems analysis.

Partially annotated bibliography for computer protection and related topics

Energy Technology Data Exchange (ETDEWEB)

Huskamp, J.C.

1976-07-20

References for the commonly cited technical papers in the area of computer protection are given. Great care is taken to exclude papers with no technical content or merit. For the purposes of this bibliography, computer protection is broadly defined to encompass all facets of the protection problem. The papers cover, but are not limited to, the topics of protection features in operating systems (e.g., MULTICS and HYDRA), hardware implementations of protection facilities (e.g., Honeywell 6180, System 250, BCC 5000, B6500), data base protection controls, confinement and protection models. Since computer protection is related to many other areas in computer science and electrical engineering, a bibliography of related areas is included after the protection bibliography. These sections also include articles of general interest in the named areas which are not necessarily related to protection.

Machine protection systems

CERN Document Server

Macpherson, A L

2010-01-01

A summary of the Machine Protection System of the LHC is given, with particular attention given to the outstanding issues to be addressed, rather than the successes of the machine protection system from the 2009 run. In particular, the issues of Safe Machine Parameter system, collimation and beam cleaning, the beam dump system and abort gap cleaning, injection and dump protection, and the overall machine protection program for the upcoming run are summarised.

Quantum confinement effects on the thermoelectric figure of merit in Si/Si{sub 1{minus}x}Ge{sub x} system

Energy Technology Data Exchange (ETDEWEB)

Sun, X; Dresselhaus, M S; Wang, K L; Tanner, M O

1997-07-01

The Si/Si{sub 1{minus}x}Ge{sub x} quantum well system is attractive for high temperature thermoelectric applications and for demonstration of proof-of-principle for enhanced thermoelectric figure of merit Z, since the interfaces and carrier densities can be well controlled in this system. The authors report here theoretical calculations for Z in this system, and results from theoretical modeling of quantum confinement effects in the presence of {delta}-doping within the barrier layers. The {delta}-doping layers are introduced by growing very thin layers of wide band gap materials within the barrier layers in order to increase the effective barrier height within the barriers and thereby reduce the barrier width necessary for the quantum confinement of carriers within the quantum well. The overall figure of merit is thereby enhanced due to the reduced barrier width and hence reduced thermal conductivity, {kappa}. The {delta}-doping should further reduce {kappa} in the barriers by introducing phonon scattering centers within the barrier region. The temperature dependence of Z for Si quantum wells is also discussed.

Exercice MERIT 2017 en passe de s’achever !

CERN Multimedia

Staff Association

2017-01-01

Les lignes directrices 2017 du MERIT (https://cds.cern.ch/record/2239422/files/2017_MERIT_Guidelines.pdf?version=1), approuvées par le Comité de Concertation permanent (CCP), concernent divers processus et procédures parmi lesquels, l’exercice annuel (ou entretien MERIT), la promotion, le changement d’emploi repère. Les processus « exercice annuel » et « promotions » - « changement d’emploi repère » ont été programmés sur deux périodes : du 1er décembre 2016 au 15 juin 2017, les entretiens MERIT, l’évaluation, la qualification et la rétribution de la performance, avec effet sur le salaire de mai ; du 3 avril 2017 au 1er juillet 2017, les promotions et les changements d’emploi repère. Entretie...

[New International Classification of Chronic Pancreatitis (M-ANNHEIM multifactor classification system, 2007): principles, merits, and demerits].

Science.gov (United States)

Tsimmerman, Ia S

2008-01-01

The new International Classification of Chronic Pancreatitis (designated as M-ANNHEIM) proposed by a group of German specialists in late 2007 is reviewed. All its sections are subjected to analysis (risk group categories, clinical stages and phases, variants of clinical course, diagnostic criteria for "established" and "suspected" pancreatitis, instrumental methods and functional tests used in the diagnosis, evaluation of the severity of the disease using a scoring system, stages of elimination of pain syndrome). The new classification is compared with the earlier classification proposed by the author. Its merits and demerits are discussed.

Young children consider merit when sharing resources with others.

Science.gov (United States)

Kanngiesser, Patricia; Warneken, Felix

2012-01-01

MERIT IS A KEY PRINCIPLE OF FAIRNESS: rewards should be distributed according to how much someone contributed to a task. Previous research suggests that children have an early ability to take merit into account in third-party situations but that merit-based sharing in first-party contexts does not emerge until school-age. Here we provide evidence that three- and five-year-old children already use merit to share resources with others, even when sharing is costly for the child. In Study 1, a child and a puppet-partner collected coins that were later exchanged for rewards. We varied the work-contribution of both partners by manipulating how many coins each partner collected. Children kept fewer stickers in trials in which they had contributed less than in trials in which they had contributed more than the partner, showing that they took merit into account. Few children, however, gave away more than half of the stickers when the partner had worked more. Study 2 confirmed that children related their own work-contribution to their partner's, rather than simply focusing on their own contribution. Taken together, these studies show that merit-based sharing is apparent in young children; however it remains constrained by a self-serving bias.

Young children consider merit when sharing resources with others.

Directory of Open Access Journals (Sweden)

Patricia Kanngiesser

Full Text Available MERIT IS A KEY PRINCIPLE OF FAIRNESS: rewards should be distributed according to how much someone contributed to a task. Previous research suggests that children have an early ability to take merit into account in third-party situations but that merit-based sharing in first-party contexts does not emerge until school-age. Here we provide evidence that three- and five-year-old children already use merit to share resources with others, even when sharing is costly for the child. In Study 1, a child and a puppet-partner collected coins that were later exchanged for rewards. We varied the work-contribution of both partners by manipulating how many coins each partner collected. Children kept fewer stickers in trials in which they had contributed less than in trials in which they had contributed more than the partner, showing that they took merit into account. Few children, however, gave away more than half of the stickers when the partner had worked more. Study 2 confirmed that children related their own work-contribution to their partner's, rather than simply focusing on their own contribution. Taken together, these studies show that merit-based sharing is apparent in young children; however it remains constrained by a self-serving bias.

Reward Merit with Praise.

Science.gov (United States)

Andrews, Hans A.

1987-01-01

Describes the efforts of two educational institutions to reward teaching excellence using positive feedback rather than merit pay incentives. An Arizona district, drawing on Herzberg's motivation theories, offers highly individualized rewards ranging from computers to conference money, while an Illinois community college bestows engraved plaques…

Simulation of quenches in SSC magnets with passive quench protection

International Nuclear Information System (INIS)

Koepke, K.

1985-06-01

The relative ease of protecting an SSC magnet following a quench and the implications of quench protection on magnet reliability and operation are necessary inputs in a rational magnet selection process. As it appears likely that the magnet selection will be made prior to full scale prototype testing, an alternative means is required to ascertain the surviveability of contending magnet types. This paper attempts to provide a basis for magnet selection by calculating the peak expected quench temperatures in the 3 T Design C magnet and the 6 T Design D magnet as a function of magnet length. A passive, ''cold diode'' protection system has been assumed. The relative merits of passive versus active protection systems have been discussed in a previous report. It is therefore assumed that - given the experience gained from the Tevatron system - that an active quench protection system can be employed to protect the magnets in the eventuality of unreliable cold diode function

FPGA-Based Plant Protection System

Energy Technology Data Exchange (ETDEWEB)

Lee, Yoon Hee; Ha, Jae Hong; Kim, Hang Bae [KEPCO E and C, Daejeon (Korea, Republic of)

2011-08-15

This paper relates to a plant protection system which detects non-permissible conditions and determines initiation of protective actions for nuclear power plants (NPPs). Conventional plant protection systems were designed based on analog technologies. It is well known that existing protection systems for NPPs contain many components which are becoming obsolete at an increasing rate. Nowadays maintenance and repair for analog-based plant protection systems may be difficult as analog parts become obsolete or difficult to obtain. Accordingly, as an alternative to the analog technology, the digitalisation of the plant protection system was required. Recently digital plant protection systems which include programmable logic controllers (PLCs) and/or computers have been introduced. However PLC or computer-based plant protection systems use an operating system and application software, and so they may result in a common mode failure when a problem occurs in the operating system or application software. Field Programmable Gate Arrays (FPGAs) are highlighted as an alternative to conventional protection or control systems. The paper presents the design of a four-channel plant protection system whose protection functions are implemented in FPGAs without any central processing unit or operating system.

FPGA-Based Plant Protection System

International Nuclear Information System (INIS)

Lee, Yoon Hee; Ha, Jae Hong; Kim, Hang Bae

2011-01-01

This paper relates to a plant protection system which detects non-permissible conditions and determines initiation of protective actions for nuclear power plants (NPPs). Conventional plant protection systems were designed based on analog technologies. It is well known that existing protection systems for NPPs contain many components which are becoming obsolete at an increasing rate. Nowadays maintenance and repair for analog-based plant protection systems may be difficult as analog parts become obsolete or difficult to obtain. Accordingly, as an alternative to the analog technology, the digitalisation of the plant protection system was required. Recently digital plant protection systems which include programmable logic controllers (PLCs) and/or computers have been introduced. However PLC or computer-based plant protection systems use an operating system and application software, and so they may result in a common mode failure when a problem occurs in the operating system or application software. Field Programmable Gate Arrays (FPGAs) are highlighted as an alternative to conventional protection or control systems. The paper presents the design of a four-channel plant protection system whose protection functions are implemented in FPGAs without any central processing unit or operating system

Depth protection system

International Nuclear Information System (INIS)

Arita, Setsuo; Izumi, Shigeru; Suzuki, Satoru; Noguchi, Atomi.

1988-01-01

Purpose: To previously set a nuclear reactor toward safety side by the reactor scram if an emergency core cooling system is failed to operate. Constitution If abnormality occurs in an emergency core cooling system or an aqueous boric acid injection system, a reactor protection system is operated and, if the reactor protection system shows an abnormal state, a control rod withdrawal inhibition system is operated as a fundamental way. For instance, when the driving power source voltage for the emergency core cooling system is detected and, if it is lower than a predetermined value, the reactor protection system is operated. Alternatively, if the voltage goes lower than the predetermined value, the control rod withdrawal is inhibited. In addition, stopping for the feedwater system is inhibited. Further, integrity of the driving means for the emergency core cooling system is positively checked and the protection function is operated depending on the result of check. Since the nuclear reactor can be set toward the safety side even if the voltage for the driving power source of the aqueous boric acid injection system is lower than a predetermined value, the reactor safety can further be improved. (Horiuchi, T.)

System level ESD protection

CERN Document Server

Vashchenko, Vladislav

2014-01-01

This book addresses key aspects of analog integrated circuits and systems design related to system level electrostatic discharge (ESD) protection.  It is an invaluable reference for anyone developing systems-on-chip (SoC) and systems-on-package (SoP), integrated with system-level ESD protection. The book focuses on both the design of semiconductor integrated circuit (IC) components with embedded, on-chip system level protection and IC-system co-design. The readers will be enabled to bring the system level ESD protection solutions to the level of integrated circuits, thereby reducing or completely eliminating the need for additional, discrete components on the printed circuit board (PCB) and meeting system-level ESD requirements. The authors take a systematic approach, based on IC-system ESD protection co-design. A detailed description of the available IC-level ESD testing methods is provided, together with a discussion of the correlation between IC-level and system-level ESD testing methods. The IC-level ESD...

Merit Pay and Music Education: A Motivation Perspective

Science.gov (United States)

Vagi, Robert

2014-01-01

Recently, state and federal legislators have emphasized teacher quality in their efforts to improve public education. Many reformers believe that merit pay may prove invaluable in attracting highly qualified educators to the workforce and retaining them, as well as in improving students' test scores. While merit pay's ability to recruit and retain…

Clinical track faculty: merits and issues.

Science.gov (United States)

Lee, Won-Hee; Kim, Cho Ja; Roh, Young Sook; Shin, Hyunsook; Kim, Mi Ja

2007-01-01

Clinical track faculty (CTF) has been in operation for more than two decades in the United States, and 12 of the top 20 schools of nursing with the highest National Institutes of Health funding in the United States have CTF in place. Yet, only limited articles have been published regarding the merits and issues related to its operation. This article examines the advantages/merits of establishing CTF in schools of nursing, discusses the qualification criteria and types of appointment for CTF, and analyzes issues related to operating CTF in Korea. A questionnaire survey and two workshops were conducted involving faculty from a college of nursing and clinical nurse managers from university-affiliated medical centers and community agencies. Most of the respondents indicated that establishing CTF was advantageous. Merits included the following: increasing reality-based clinical education and training; decreasing the reality shock of students; increasing student satisfaction; and linking education, practice, and research more effectively. Major issues were as follows: getting the approval of medical centers/universities; developing an agreement on CTF operation between the college of nursing and clinical agencies; clarifying types and criteria of appointment and promotion; and developing a statement on role and compensation policies. Most issues are similar to what U.S. schools of nursing have faced, except for the first one. In conclusion, establishing CTF in Korea appears to be highly desirable. Merits outweigh issues/concerns, and Korean nursing schools may look for an opportune time for obtaining the approval of medical centers/universities. Nursing schools in other countries that face a similar challenge of providing clinical teaching with high research performance may consider instituting CTF.

Power system protection

International Nuclear Information System (INIS)

Venkata, S.S.; Damborg, M.J.; Jampala, A.K.

1991-01-01

Power systems of the 21st century will be more modern, and complex, utilizing the latest available technologies. At the same time, generating plants will have to operate with minimal spinning margins and energy transportation has to take place at critical levels due to environmental and economical constraints. These factors dictate that the power systems be protected with optimum sensitivity, selectivity and time of operation to assure maximum reliability, and security at minimal cost. With an increasing role played by digital computers in every aspect of protection, it is important to take a critical and fresh look at the art and science of relaying and protection. The main objective of this paper is to review the past, present and future of power system protection from a software point of view

Wind energy and electricity prices. Exploring the 'merit order effect'

International Nuclear Information System (INIS)

Morthost, P.E.; Ray, S.; Munksgaard, J.; Sinner, A.F.

2010-04-01

This report focuses on the effect of wind energy on the electricity price in the power market. As the report will discuss, adding wind into the power mix has a significant influence on the resulting price of electricity, the so called merit order effect (MOE). The merit order effect has been quantified and discussed in many scientific publications. This report ends the first phase of a study on the MOE, evaluating the impact of EWEA's 2020 scenarios on future European electricity prices. The basic principles of the merit order effect are provided in the first part of the document. The literature review itself contains methods and tools not only to quantify the merit order effect but also in order to forecast its future range and volume.

Radiation protection for human exploration of the moon and mars: Application of the mash code system

International Nuclear Information System (INIS)

Johnson, J.O.; Santoro, R.T.; Drischler, J.D.; Barnes, J.M.

1992-01-01

The Monte Carlo Adjoint Shielding code system -- MASH, developed for the Department of Defense for calculating radiation protection factors for armored vehicles against neutron and gamma radiation, has been used to assess the dose from reactor radiation to an occupant in a habitat on Mars. The capability of MASH to reproduce measured data is summarized to demonstrate the accuracy of the code. The estimation of the radiation environment in an idealized reactor-habitat model is reported to illustrate the merits of the adjoint Monte Carlo procedure for space related studies. The reactor radiation dose for different reactor-habitat surface configurations to a habitat occupant is compared with the natural radiation dose acquired during a 500-day Mars mission

On-Chip Sensing of Thermoelectric Thin Film’s Merit

OpenAIRE

Xiao, Zhigang; Zhu, Xiaoshan

2015-01-01

Thermoelectric thin films have been widely explored for thermal-to-electrical energy conversion or solid-state cooling, because they can remove heat from integrated circuit (IC) chips or micro-electromechanical systems (MEMS) devices without involving any moving mechanical parts. In this paper, we report using silicon diode-based temperature sensors and specific thermoelectric devices to characterize the merit of thermoelectric thin films. The silicon diode temperature sensors and thermoelect...

Buffer moisture protection system

International Nuclear Information System (INIS)

Ritola, J.; Peura, J.

2013-11-01

With the present knowledge, bentonite blocks have to be protected from the air relative humidity and from any moisture leakages in the environment that might cause swelling of the bentonite blocks during the 'open' installation phase before backfilling. The purpose of this work was to design the structural reference solution both for the bottom of the deposition hole and for the buffer moisture protection and dewatering system with their integrated equipment needed in the deposition hole. This report describes the Posiva's reference solution for the buffer moisture protection system and the bottom plate on basis of the demands and functional requirements set by long-term safety. The reference solution with structural details has been developed in research work made 2010-2011. The structural solution of the moisture protection system has not yet been tested in practice. On the bottom of the deposition hole a copper plate which protects the lowest bentonite block from the gathered water is installed straight to machined and even rock surface. The moisture protection sheet made of EPDM rubber is attached to the copper plate with an inflatable seal. The upper part of the moisture protection sheet is fixed to the collar structures of the lid which protects the deposition hole in the disposal tunnel. The main function of the moisture protection sheet is to protect bentonite blocks from the leaking water and from the influence of the air humidity at their installation stage. The leaking water is controlled by the dewatering and alarm system which has been integrated into the moisture protection liner. (orig.)

Time Structure of Particle Production in the Merit High-Power Target Experiment

CERN Document Server

Efthymiopoulos, I; Palm, M; Lettry, J; Haug, F; Pereira, H; Pernegger, H; Steerenberg, R; Grudiev, A; Kirk, H G; Park, H; Tsang, T; Mokhov, N; Striganov, S; Carroll, A J; Graves, V B; Spampinato, P T; McDonald, K T; Bennett, J R J; Caretta, O; Loveridge, P

2010-01-01

The MERIT experiment is a proof-of-principle test of a target system for high power proton beam to be used as front-end for a neutrino factory complex or amuon collider. The experiment took data in autumn 2007 with the fast extracted beam from the CERN Proton Synchrotron (PS) to a maximum intensity of about 30 × 1012 protons per pulse. We report results from the portion of the MERIT experiment in which separated beam pulses were delivered to a free mercury jet target with time intervals between pulses varying from 2 to 700 μs. The analysis is based on the responses of particle detectors placed along side and downstream of the target.

FIRE PROTECTION SYSTEMS AND TECHNOLOGIES

Directory of Open Access Journals (Sweden)

Aristov Denis Ivanovich

2016-03-01

Full Text Available The All-Russian Congress “Fire Stop Moscow” was de-voted to the analysis of the four segments of the industry of fire protection systems and technologies: the design of fire protec-tion systems, the latest developments and technologies of active and passive fire protection of buildings, the state and the devel-opment of the legal framework, the practice of fire protection of buildings and structures. The forum brought together the repre-sentatives of the industry of fire protection systems, scientists, leading experts, specialists in fire protection and representatives of construction companies from different regions of Russia. In parallel with the Congress Industrial Exhibition of fire protection systems, materials and technology was held, where manufacturers presented their products. The urgency of the “Fire Stop Moscow” Congress in 2015 organized by the Congress Bureau ODF Events lies primarily in the fact that it considered the full range of issues related to the fire protection of building and construction projects; studied the state of the regulatory framework for fire safety and efficiency of public services, research centers, private companies and busi-nesses in the area of fire safety. The main practical significance of the event which was widely covered in the media space, was the opportunity to share the views and information between management, science, and practice of business on implementing fire protection systems in the conditions of modern economic relations and market realities. : congress, fire protection, systems, technologies, fire protection systems, exhibition

Characteristics of National Merit Scholars from Small Rural Schools.

Science.gov (United States)

Peltier, Gary; And Others

This study compares 1988 National Merit Scholars enrolled in rural public schools with a senior class smaller than 99 students to other merit scholars and the national sample of SAT takers. Rural scholars were more likely to be female (45.5%) and Caucasian (98%) than other scholars. Involvement in extracurricular activities was significantly…

Profiles of Merit Pay Provisions in Ohio School Districts

Science.gov (United States)

Willis, Chris; Ingle, W. Kyle

2018-01-01

A small number of districts in Ohio from a variety of locales have adopted merit pay provisions. Using Springer's (2009) taxonomy of teacher compensation, we analyzed compensation provisions of these districts. We asked: What are the characteristics of these districts? What criteria are used to determine merit? Who is determining who receives…

The merit of cogeneration: Measuring and rewarding performance

International Nuclear Information System (INIS)

Verbruggen, Aviel

2008-01-01

Cogeneration or combined heat and power (CHP) is a thermal power generation cycle with the merit of recovering part or all of the heat that is fatally discarded by such cycles. This merit of higher efficiency is subject of rewarding by public authorities. When the EU enacts CHP promotion in a Directive (1997-2004), crucial measurement and qualification issues remain unsolved. CEN (coordinator of the European Bureaus of Standards) contributes in clarifying the measurement of CHP activities, but shortfalls remain, while CEN bypasses the debate on qualifying CHP performance. This article offers appropriate methods for measuring CHP activities based on design characteristics of the plants. The co-generated electric output is a necessary and sufficient indicator of CHP merit and performance. Regulators can extend this indicator, but should avoid the perverse effects of biased external benchmarking as the EU Directive entails

2008 DOE Hydrogen Program Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

none,

2008-06-13

This report summarizes comments from the Peer Review Panel at the 2008 DOE Hydrogen Program Annual Merit Review, held on June 9-13, 2008, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; technology validation; safety, codes, and standards; education; systems analysis; and manufacturing.

Kainic Acid-Induced Excitotoxicity Experimental Model: Protective Merits of Natural Products and Plant Extracts

Directory of Open Access Journals (Sweden)

Nur Shafika Mohd Sairazi

2015-01-01

Full Text Available Excitotoxicity is well recognized as a major pathological process of neuronal death in neurodegenerative diseases involving the central nervous system (CNS. In the animal models of neurodegeneration, excitotoxicity is commonly induced experimentally by chemical convulsants, particularly kainic acid (KA. KA-induced excitotoxicity in rodent models has been shown to result in seizures, behavioral changes, oxidative stress, glial activation, inflammatory mediator production, endoplasmic reticulum stress, mitochondrial dysfunction, and selective neurodegeneration in the brain upon KA administration. Recently, there is an emerging trend to search for natural sources to combat against excitotoxicity-associated neurodegenerative diseases. Natural products and plant extracts had attracted a considerable amount of attention because of their reported beneficial effects on the CNS, particularly their neuroprotective effect against excitotoxicity. They provide significant reduction and/or protection against the development and progression of acute and chronic neurodegeneration. This indicates that natural products and plants extracts may be useful in protecting against excitotoxicity-associated neurodegeneration. Thus, targeting of multiple pathways simultaneously may be the strategy to maximize the neuroprotection effect. This review summarizes the mechanisms involved in KA-induced excitotoxicity and attempts to collate the various researches related to the protective effect of natural products and plant extracts in the KA model of neurodegeneration.

2010 DOE Hydrogen Program Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

none,

2010-12-01

This report summarizes comments from the Peer Review Panel at the 2010 DOE Hydrogen Program Annual Merit Review, held on June 7-11, 2010, in Washington, DC. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; education; and systems analysis.

2009 DOE Hydrogen Program Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

Satyapal, S. [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

2009-10-01

This report summarizes comments from the Peer Review Panel at the 2009 DOE Hydrogen Program Annual Merit Review, held on May 18-22, 2009, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; education; safety, codes, and standards; technology validation; systems analysis; and manufacturing R&D.

Reactor protection system

International Nuclear Information System (INIS)

Fairbrother, D.B.; Lesniak, L.M.; Orgera, E.G.

1977-10-01

The report describes the reactor protection system (RPS-II) designed for use on Babcock and Wilcox 145-, later 177-, and 205-fuel assembly pressurized water reactors. In this system, relays in the trip logic have been replaced by solid state devices. A calculating module for the low DNBR, pump status, and offset trip functions has replaced the overpower trip (based on flow and imbalance), the power/RC pump trip, and the variable low-pressure trip. Included is a description of the changes from the present Oconee-type reactor protection system (RPS-I), a functional and hardware description of the calculating module, a description of the software programmed in the calculating module, and a discussion of the qualification program conducted to ensure that the degree of protection provided by RPS-II is not less than that provided by previously licensed systems supplied by B and W

Systems approach to tamper protection

International Nuclear Information System (INIS)

Myre, W.C.; Eaton, M.J.

1980-01-01

Tamper-protection is a fundamental requirement of effective containment and surveillance systems. Cost effective designs require that the tamper protection requirements be considered early in the design phase and at the system level. A discussion of tamper protection alternatives as well as an illustrative example system is presented

Merit pay as a motivator in the federal sector.

OpenAIRE

Engel, James D.

1982-01-01

Approved for public release; distribution is unlimited The Civil Service Reform Act of 1978 required the implementation of the Merit Pay System for a portion of the Federal civilian workforce as a means of increasing productivity through the use of monetary incentives. To test the validity of this concept, several theories of worker motivation are reviewed and their relation to money motivation and pay-for-performance is established. These relationships are compared to the results of dat...

Performance appraisal and merit recognition exercise 2007

CERN Multimedia

HR Department

2006-01-01

The 2007 performance appraisal and merit recognition exercise will start in the usual way with annual interviews between staff and their supervisors. This year, these interviews should be held in the period from 8 January 2007 to 16 April 2007. Interconnection with the 5-yearly review, a number of modifications to the procedures relating to the performance appraisal and merit recognition are currently under study. Administrative Circular No. 26 (Procedures governing the Career Development of Staff Members) and the electronic MAPS form in EDH are being reviewed and will be available from January onwards. HR Department will shortly provide further information on this subject. Human Resources Department Tel. 73566

Physical protection system design and evaluation

International Nuclear Information System (INIS)

Williams, J.D.

1997-01-01

The design of an effective physical protection system includes the determination of physical protection system objectives, initial design of a physical protection system, design evaluation, and probably a redesign or refinement. To develop the objectives, the designer must begin by gathering information about facility operation and conditions, such as a comprehensive description of the facility, operating conditions, and the physical protection requirements. The designer then needs to define the threat. This involves considering factors about potential adversaries: class of adversary, adversary's capabilities, and range of adversary's tactics. Next, the designer should identify targets. Determination of whether or not the materials being protected are attractive targets is based mainly on the ease or difficulty of acquisition and desirability of the material. The designer now knows the objectives of the physical protection system, that is, open-quotes what to protect against whom.close quotes The next step is to design the system by determining how best to combine such elements as fences, vaults, sensors and assessment devices, entry control elements, procedures, communication devices, and protective forces personnel to meet the objectives of the system. Once a physical protection system is designed, it must be analyzed and evaluated to ensure it meets the physical protection objectives. Evaluation must allow for features working together to ensure protection rather than regarding each feature separately. Due to the complexity of the protection systems, an evaluation usually requires modeling techniques. If any vulnerabilities are found, the initial system must be redesigned to correct the vulnerabilities and a reevaluation conducted. This paper reviews the physical protection system design and methodology mentioned above. Examples of the steps required and a brief introduction to some of the technologies used in modem physical protections system are given

Investigation of High-Efficiency Wireless Power Transfer Criteria of Resonantly-Coupled Loops and Dipoles through Analysis of the Figure of Merit

Directory of Open Access Journals (Sweden)

Charles Moorey

2015-10-01

Full Text Available The efficiency of a Wireless Power Transfer (WPT system is greatly dependent on both the geometry and operating frequency of the transmitting and receiving structures. By using Coupled Mode Theory (CMT, the figure of merit is calculated for resonantly-coupled loop and dipole systems. An in-depth analysis of the figure of merit is performed with respect to the key geometric parameters of the loops and dipoles, along with the resonant frequency, in order to identify the key relationships leading to high-efficiency WPT. For systems consisting of two identical single-turn loops, it is shown that the choice of both the loop radius and resonant frequency are essential in achieving high-efficiency WPT. For the dipole geometries studied, it is shown that the choice of length is largely irrelevant and that as a result of their capacitive nature, low-MHz frequency dipoles are able to produce significantly higher figures of merit than those of the loops considered. The results of the figure of merit analysis are used to propose and subsequently compare two mid-range loop and dipole WPT systems of equal size and operating frequency, where it is shown that the dipole system is able to achieve higher efficiencies than the loop system of the distance range examined.

2008 annual merit review

Energy Technology Data Exchange (ETDEWEB)

None, None

2009-01-18

The 2008 DOE Vehicle Technologies Program Annual Merit Review was held February 25-28, 2008 in Bethesda, Maryland. The review encompassed all of the work done by the Vehicle Technologies Program: a total of 280 individual activities were reviewed, by a total of just over 100 reviewers. A total of 1,908 individual review responses were received for the technical reviews, and an additional 29 individual review responses were received for the plenary session review.

SMART core protection system design

International Nuclear Information System (INIS)

Lee, J. K.; Park, H. Y.; Koo, I. S.; Park, H. S.; Kim, J. S.; Son, C. H.

2003-01-01

SMART COre Protection System(SCOPS) is designed with real-tims Digital Signal Processor(DSP) board and Network Interface Card(NIC) board. SCOPS has a Control Rod POSition (CRPOS) software module while Core Protection Calculator System(CPCS) consists of Core Protection Calculators(CPCs) and Control Element Assembly(CEA) Calculators(CEACs) in the commercial nuclear plant. It's not necessary to have a independent cabinets for SCOPS because SCOPS is physically very small. Then SCOPS is designed to share the cabinets with Plant Protection System(PPS) of SMART. Therefor it's very easy to maintain the system because CRPOS module is used instead of the computer with operating system

Evolution of the radiation protection system; L'evolution du systeme de protection radiologique

Energy Technology Data Exchange (ETDEWEB)

Clarke, R.H. [International Commission on Radiological Protection, Stockholm (Sweden); Schieber, C.; Cordoliani, Y.S. [Societe Francaise de Radioprotection, 92 - Fontenay aux Roses (France); Brechignac, F. [CEA Cadarache, Institut de Radioprotection et de Surete Nucleaire, Dept. de Protection de l' Environnement, 13 - Saint Paul Lez Durance (France)

2003-07-01

The evolution of the system of radiological protection: justification for new ICRP recommendations, thoughts of the SFRP work group about the evolution of the system of radiation protection proposed by the ICRP, protection of environment against ionizing radiations seen by the ICRP are the three parts of this chapter. (N.C.)

Redefining the merit order of stochastic generation in forward markets

DEFF Research Database (Denmark)

Morales González, Juan Miguel; Zugno, Marco; Pineda Morente, Salvador

2014-01-01

This letter proposes a new merit order for the dispatch of stochastic production in forward markets (e.g., dayahead markets). The proposed merit order considers not only the marginal cost of the stochastic generating unit, which is often very low or zero, but also the projected cost of balancing...

Digital integrated protection system

International Nuclear Information System (INIS)

Savornin, M.; Furet, M.

1978-01-01

As a result of technological progress it is now possible to achieve more elaborate protection functions able to follow more closely the phenomena to be supervised. For this reason the CEA, Framatome and Merlin/Gerin/CERCI have undertaken in commonn to develop a Digital Integrated Protection System (D.I.P.S.). This system is designed with the following aims: to improve the safety of the station, . to improve its availability, . to facilitate installation, . to facilitate tests and maintenance. The main characteristics adopted are: . possibilities of obtaining more elaborate monitoring and protection algorithm treatments, . order 4 redundancy of transducers, associated instruments and signal processing, . possibility of inhibiting part of the protection system, . standardisation of equipment, physical and electrical separation of redundant units, . use of multiplexed connections, . automation of tests. Four flow charts are presented: - DIPS with four APUP (Acquisition and Processing Unit for Protection) - APUP - LSU (Logic Safeguard Unit), number LSU corresponding to number fluidic safeguard circuits, - structure of a function unit, - main functions of the APUP [fr

Effect of Remote Back-Up Protection System Failure on the Optimum Routine Test Time Interval of Power System Protection

Directory of Open Access Journals (Sweden)

Y Damchi

2013-12-01

Full Text Available Appropriate operation of protection system is one of the effective factors to have a desirable reliability in power systems, which vitally needs routine test of protection system. Precise determination of optimum routine test time interval (ORTTI plays a vital role in predicting the maintenance costs of protection system. In the most previous studies, ORTTI has been determined while remote back-up protection system was considered fully reliable. This assumption is not exactly correct since remote back-up protection system may operate incorrectly or fail to operate, the same as the primary protection system. Therefore, in order to determine the ORTTI, an extended Markov model is proposed in this paper considering failure probability for remote back-up protection system. In the proposed Markov model of the protection systems, monitoring facility is taken into account. Moreover, it is assumed that the primary and back-up protection systems are maintained simultaneously. Results show that the effect of remote back-up protection system failures on the reliability indices and optimum routine test intervals of protection system is considerable.

Merit-Based Incentive Payment System: Meaningful Changes in the Final Rule Brings Cautious Optimism.

Science.gov (United States)

Manchikanti, Laxmaiah; Helm Ii, Standiford; Calodney, Aaron K; Hirsch, Joshua A

2017-01-01

The Medicare Access and CHIP Reauthorization Act of 2015 (MACRA) eliminated the flawed Sustainable Growth Rate (SGR) act formula - a longstanding crucial issue of concern for health care providers and Medicare beneficiaries. MACRA also included a quality improvement program entitled, "The Merit-Based Incentive Payment System, or MIPS." The proposed rule of MIPS sought to streamline existing federal quality efforts and therefore linked 4 distinct programs into one. Three existing programs, meaningful use (MU), Physician Quality Reporting System (PQRS), value-based payment (VBP) system were merged with the addition of Clinical Improvement Activity category. The proposed rule also changed the name of MU to Advancing Care Information, or ACI. ACI contributes to 25% of composite score of the four programs, PQRS contributes 50% of the composite score, while VBP system, which deals with resource use or cost, contributes to 10% of the composite score. The newest category, Improvement Activities or IA, contributes 15% to the composite score. The proposed rule also created what it called a design incentive that drives movement to delivery system reform principles with the inclusion of Advanced Alternative Payment Models (APMs).Following the release of the proposed rule, the medical community, as well as Congress, provided substantial input to Centers for Medicare and Medicaid Services (CMS),expressing their concern. American Society of Interventional Pain Physicians (ASIPP) focused on 3 important aspects: delay the implementation, provide a 3-month performance period, and provide ability to submit meaningful quality measures in a timely and economic manner. The final rule accepted many of the comments from various organizations, including several of those specifically emphasized by ASIPP, with acceptance of 3-month reporting period, as well as the ability to submit non-MIPS measures to improve real quality and make the system meaningful. CMS also provided a mechanism for

Adaptive protection algorithm and system

Science.gov (United States)

Hedrick, Paul [Pittsburgh, PA; Toms, Helen L [Irwin, PA; Miller, Roger M [Mars, PA

2009-04-28

An adaptive protection algorithm and system for protecting electrical distribution systems traces the flow of power through a distribution system, assigns a value (or rank) to each circuit breaker in the system and then determines the appropriate trip set points based on the assigned rank.

Advanced Worker Protection System

International Nuclear Information System (INIS)

1996-04-01

The Advanced Worker Protection System (AWPS) is a liquid-air-based, self-contained breathing and cooling system with a duration of 2 hrs. AWPS employs a patented system developed by Oceaneering Space Systems (OSS), and was demonstrated at their facility in Houston, TX as well as at Kansas State University, Manhattan. The heart of the system is the life-support backpack that uses liquid air to provide cooling as well as breathing gas to the worker. The backpack is combined with advanced protective garments, an advanced liquid cooling garment (LCG), a respirator, and communications and support equipment. The prototype unit development and testing under Phase 1 has demonstrated that AWPS has the ability to meet performance criteria. These criteria were developed with an understanding of both the AWPS capabilities and the DOE decontamination and decommissioning (D and D) activities protection needs

Protection of industrial power systems

CERN Document Server

DAVIES, T

2006-01-01

The protection which is installed on an industrial power system is likely to be subjected to more difficult conditions than the protection on any other kind of power system. Starting with the many simple devices which are employed and covering the whole area of industrial power system protection, this book aims to help achieve a thorough understanding of the protection necessary.Vital aspects such as the modern cartridge fuse, types of relays, and the role of the current transformer are covered and the widely used inverse definite-minimum time overcurrent relay, the theory of the M

Relay protection coordination with generator capability curve, excitation system limiters and power system relay protections settings

Directory of Open Access Journals (Sweden)

Buha Danilo

2016-01-01

Full Text Available The relay protection settings performed in the largest thermal powerplant (TE "Nikola Tesla B" are reffered and explained in this paper. The first calculation step is related to the coordination of the maximum stator current limiter settings, the overcurrent protection with inverse characteristics settings and the permitted overload of the generator stator B1. In the second calculation step the settings of impedance generator protection are determined, and the methods and criteria according to which the calculations are done are described. Criteria used to provide the protection to fulfill the backup protection role in the event of malfunction of the main protection of the transmission system. are clarified. The calculation of all protection functions (32 functions of generator B1 were performed in the project "Coordination of relay protection blocks B1 and B2 with the system of excitation and power system protections -TENT B".

Protective and Catching Safety Systems In Construction

Directory of Open Access Journals (Sweden)

Kuzhin Marat

2017-01-01

Full Text Available In the article is described application of protective and catching systems in construction. Classification of similar systems, their types and purpose are listed. Dangerous zones on construction site and events to for limiting their influence or protection from the factors. Protective and catching systems is one of the most effective technical equipment, applied in recent time. Protective fences and catching systems are important part in the problem solution. Protective fences protect workers from falling from height. Protective and catching systems allows avoid injuries by workers, also catch debris, fallen from constructing buildings. In regard with continuing development in technical and technological solutions, protective and catching systems require adaptation to a new requirements of construction industry and requirements of normative documents. Technical regulations in the appliance sphere of protective and catching systems requires actualization and aligning with modern normatives. Important role should be given to developing organizational and technological documentation for application of the systems. Scientific studying of technical parameters of fences and protective catching nets also has great interest.

Publication of administrative circular No. 26 (Rev. 8) – Recognition of merit

CERN Multimedia

HR Department

2008-01-01

Administrative Circular No. 26 (Rev. 8) – Recognition of merit Administrative Circular No. 26 (Rev. 8) – "Recognition of merit", approved by the Standing Concertation Committee at its meeting on 3 September 2008, is now available on the intranet site of the Human Resources Department. It cancels and replaces Administrative Circular No. 26 (Rev. 7) – "Recognition of merit of staff members" of May 2007. Paper copies will shortly be available in Departmental secretariats. Human Resources Department Tel. 78003

Publication of administrative circular No. 26 (Rev. 8) – Recognition of merit

CERN Multimedia

HR Department

2008-01-01

Administrative Circular No. 26 (Rev. 8) – Recognition of merit Administrative Circular No. 26 (Rev. 8) – "Recognition of merit", approved by the Standing Concertation Committee meeting on 3 September 2008, is now available on the intranet site of the Human Resources Department. It cancels and replaces Administrative Circular No. 26 (Rev. 7) – "Recognition of merit of staff members" of May 2007. Paper copies will shortly be available in Departmental secretariats. Human Resources Department Tel. 78003

The effective communication methodology and influence of merit information on nuclear power

International Nuclear Information System (INIS)

Oiso, Shinichi

2007-01-01

It was found by the survey the author carried out in 2005 that there is a possibility that even the person who opposes nuclear power generation may change his or her opinion after understanding the advantage of nuclear power. Then, how should merit information be transmitted? Is there a possibility that people feel repulsion after receiving merit information? What is the influence of providing merit information of nuclear power? Those kinds of questions were investigated in 2006. As a result, it was found that the use of magazine and NPO/NGO is effective. The utilization of all-night television broadcasting, iPod, energy environmental education in schools and science cafe have an effect too, especially for young generation. It was also found that 20% or less of the people feel repulsion for providing merit information of nuclear power. Concerning people's attitude towards nuclear power utilization, it was found that the number of those who support nuclear power generation tended to increase significantly by providing information depicting merits or benefits of nuclear power, however, it did not increase by explaining electric power companies' effort to promote nuclear power. Further more, concerning to the image of a nuclear power station site, it became clear that merit information of nuclear power provided positive effect for some items in explaining nuclear power generation. (author)

Smart machine protection system

International Nuclear Information System (INIS)

Clark, S.; Nelson, D.; Grillo, A.

1992-01-01

A Machine Protection System implemented on the SLC automatically controls the beam repetition rates in the accelerator so that radiation or temperature faults slow the repetition rate to bring the fault within tolerance without shutting down the machine. This process allows the accelerators to aid in the fault diagnostic process, and the protection system automatically restores the beams back to normal rates when the fault is diagnosed and corrected. The user interface includes facilities to monitor the performance of the system, and track rate limits, faults, and recoveries. There is an edit facility to define the devices to be included in the protection system, along with their set points, limits, and trip points. This set point and limit data is downloaded into the CAMAC modules, and the configuration data is complied into a logical decision tree for the 68030 processor. (author)

Smart Machine Protection System

International Nuclear Information System (INIS)

Clark, S.; Nelson, D.; Grillo, A.; Spencer, N.; Hutchinson, D.; Olsen, J.; Millsom, D.; White, G.; Gromme, T.; Allison, S.; Underwood, K.; Zelazny, M.; Kang, H.

1991-11-01

A Machine Protection System implemented on the SLC automatically controls the beam repetition rates in the accelerator so that radiation or temperature faults slow the repetition rate to bring the fault within tolerance without shutting down the machine. This process allows the accelerator to aid in the fault diagnostic process, and the protection system automatically restores the beams back to normal rates when the fault is diagnosed and corrected. The user interface includes facilities to monitor the performance of the system, and track rate limits, faults, and recoveries. There is an edit facility to define the devices to be included in the protection system, along with their set points, limits, and trip points. This set point and limit data is downloaded into the CAMAC modules, and the configuration data is compiled into a logical decision tree for the 68030 processor. 3 figs

An Optimization Model for the Allocation of University Based Merit Aid

Science.gov (United States)

Sugrue, Paul K.

2010-01-01

The allocation of merit-based financial aid during the college admissions process presents postsecondary institutions with complex and financially expensive decisions. This article describes the application of linear programming as a decision tool in merit based financial aid decisions at a medium size private university. The objective defined for…

Deficiencies in radiation protection record systems

International Nuclear Information System (INIS)

Martin, J.B.; Lyon, M.

1991-01-01

Radiation protection records are a fundamental part of any program for protecting radiation workers. Records are essential to epidemiological studies of radiation workers and are becoming increasingly important as the number of radiation exposure litigation cases increases. Ready retrievability of comprehensive records is also essential to the adequate defense of a radiation protection program. Appraisals of numerous radiation protection programs have revealed that few record-keeping systems comply with American National Standards Institute, Standard Practice N13.6-1972. Record-keeping requirements and types of deficiencies in radiation protection records systems are presented in this paper, followed by general recommendations for implementing a comprehensive radiation protection records system

Deficiencies in radiation protection record systems

International Nuclear Information System (INIS)

Martin, J.B.; Lyon, M.

1991-01-01

Radiation protection records are a fundamental part of any program for protecting radiation workers. Records are essential to epidemiological studies of radiation workers and are becoming increasingly important as the number of radiation exposure litigation cases increases. Ready retrievability of comprehensive records is also essential to the adequate defense of a radiation protection program. Appraisals of numerous radiation protection programs have revealed that few record-keeping systems comply with American National Standards Institute, Standard Practice N13.6-1972. Record-keeping requirements and types of deficiencies in radiation protection records systems are presented in this paper, followed by general recommendations for implementing a comprehensive radiation protection records system. 8 refs

An empirically derived figure of merit for the quality of overall task performance

Science.gov (United States)

Lemay, Moira

1989-01-01

The need to develop an operationally relevant figure of merit for the quality of performance of a complex system such as an aircraft cockpit stems from a hypothesized dissociation between measures of performance and those of workload. Performance can be measured in terms of time, errors, or a combination of these. In most tasks performed by expert operators, errors are relatively rare and often corrected in time to avoid consequences. Moreover, perfect performance is seldom necessary to accomplish a particular task. Moreover, how well an expert performs a complex task consisting of a series of discrete cognitive tasks superimposed on a continuous task, such as flying an aircraft, does not depend on how well each discrete task is performed, but on their smooth sequencing. This makes the amount of time spent on each subtask of paramount importance in measuring overall performance, since smooth sequencing requires a minimum amount of time spent on each task. Quality consists in getting tasks done within a crucial time interval while maintaining acceptable continuous task performance. Thus, a figure of merit for overall quality of performance should be primarily a measure of time to perform discrete subtasks combined with a measure of basic vehicle control. Thus, the proposed figure of merit requires doing a task analysis on a series of performance, or runs, of a particular task, listing each discrete task and its associated time, and calculating the mean and standard deviation of these times, along with the mean and standard deviation of tracking error for the whole task. A set of simulator data on 30 runs of a landing task was obtained and a figure of merit will be calculated for each run. The figure of merit will be compared for voice and data link, so that the impact of this technology on total crew performance (not just communication performance) can be assessed. The effect of data link communication on other cockpit tasks will also be considered.

Thermoelectric figure of merit of polymeric systems for low-power generators

Science.gov (United States)

Cigarini, Luigi; Ruini, Alice; Catellani, Alessandra; Calzolari, Arrigo

2017-10-01

The request of thermoelectric materials for low-power and flexible applications fosters the investigation of the intrinsic electron and thermal transport of conducting polymeric chains, which are building blocks of the complex variety of organic composites proposed in experimental samples. Using calculations from first principles and the Landauer approach for both electron and phonon carriers, we study the thermoelectric figure of merit zT of three representative and largely used polymer chains, namely poly(3,4-ethylenedioxythiophene), polyaniline and polyfluorene. Our results provide an upper-limit estimate of zT, due to the intrinsic electronic and vibrational properties of the selected compounds, and pave the way to a microscopic understanding of the mechanisms that affect their electronic and transport characteristics in terms of structural distortions and chemical doping.

Selectivity of power system protections at power swings in power system

Directory of Open Access Journals (Sweden)

Jan Machowski

2012-12-01

Full Text Available The paper discusses out-of-step protection systems such as: generator pole slip protections, out of step tripping protections, distance protections of step-up transformer, distance protections of transmission lines and transformers, power swing blocking, and special out-of-step protection. It is shown that all these protections make up a protection system, to which a setting concept uniform for the entire power system has to be applied. If a power system is inappropriately equipped with these protections, or their settings are inappropriate, they may operate unselectively, thus contributing to the development of power system blackouts. In the paper the concepts for a real power system are given for the two stages: target stage fully compliant with selectivity criteria, and transitional stage between the current and target stages.

Reactor protection and shut-down system

International Nuclear Information System (INIS)

Klar

1980-01-01

The reactor protection system being a part of the reactor safety system. The requirements on the reactor protection system are: high safety with regard to signal processing, high availability, self-reporting of faults etc. The functional sections of the reactor protection system are the analog section, the logic section and the generating of output signals. Description of the operation characteristics and of the extension of function. (orig.)

Genetic merit for fertility traits in Holstein cows: I. Production characteristics and reproductive efficiency in a pasture-based system.

Science.gov (United States)

Cummins, S B; Lonergan, P; Evans, A C O; Berry, D P; Evans, R D; Butler, S T

2012-03-01

The objective of the present study was to characterize the phenotypic performance of cows with similar proportions of Holstein genetics, similar genetic merit for milk production traits, but with good (Fert+) or poor (Fert-) genetic merit for fertility traits. Specifically, we tested the hypothesis that cows with a negative estimated breeding value for calving interval would have superior fertility performance and would have detectable differences in body reserve mobilization and circulating concentrations of metabolic hormones and metabolites compared with cows that had a positive estimated breeding value for calving interval. For the duration of the study, cows were managed identically as a single herd in a typical grass-based, spring-calving production system. A total of 80 lactation records were available from 26 Fert+ and 26 Fert- cows over 2 consecutive years (2008 and 2009). During yr 1, cows were monitored during a 20-wk breeding season to evaluate reproductive performance. Milk production, body condition score (scale 1 to 5), body weight, grass dry matter intake, energy balance, and metabolic hormone and metabolite data were collected during both years. The Fert+ cows had greater daily milk yield (19.5 vs. 18.7 kg/d), shorter interval from calving to conception (85.6 vs. 113.8 d), and fewer services per cow (1.78 vs. 2.83). No difference between groups in grass dry matter intake, energy balance, or body weight was observed. The Fert+ cows maintained greater BCS during mid (2.84 vs. 2.74 units) and late lactation (2.82 vs. 2.73 units). Circulating concentrations of insulin-like growth factor-I were greater throughout the gestation-lactation cycle in Fert+ cows (148.3 vs. 128.2 ng/mL). The Fert+ cows also had greater circulating concentrations of insulin during the first 4 wk of lactation (1.71 vs. 1.24 μIU/mL). Analysis of records from national herd data verified the association between genetic merit for fertility traits and phenotypic reproductive

Metacognitive reflection and insight therapy (MERIT) for patients with schizophrenia.

Science.gov (United States)

de Jong, S; van Donkersgoed, R J M; Timmerman, M E; Aan Het Rot, M; Wunderink, L; Arends, J; van Der Gaag, M; Aleman, A; Lysaker, P H; Pijnenborg, G H M

2018-04-25

Impaired metacognition is associated with difficulties in the daily functioning of people with psychosis. Metacognition can be divided into four domains: Self-Reflection, Understanding the Other's Mind, Decentration, and Mastery. This study investigated whether Metacognitive Reflection and Insight Therapy (MERIT) can be used to improve metacognition. This study is a randomized controlled trial. Patients in the active condition (n = 35) received forty MERIT sessions, the control group (n = 35) received treatment as usual. Multilevel intention-to-treat and completers analyses were performed for metacognition and secondary outcomes (psychotic symptomatology, cognitive insight, Theory of Mind, empathy, depression, self-stigma, quality of life, social functioning, and work readiness). Eighteen out of 35 participants finished treatment, half the drop-out stemmed from therapist attrition (N = 5) or before the first session (N = 4). Intention-to-treat analysis demonstrated that in both groups metacognition improved between pre- and post-measurements, with no significant differences between the groups. Patients who received MERIT continued to improve, while the control group returned to baseline, leading to significant differences at follow-up. Completers analysis (18/35) showed improvements on the Metacognition Assessment Scale (MAS-A) scales Self Reflectivity and metacognitive Mastery at follow-up. No effects were found on secondary outcomes. On average, participants in the MERIT group were, based on MAS-A scores, at follow-up more likely to recognize their thoughts as changeable rather than as facts. MERIT might be useful for patients whose self-reflection is too limited to benefit from other therapies. Given how no changes were found in secondary measures, further research is needed. Limitations and suggestions for future research are discussed.

Regulatory control of physical protection systems

International Nuclear Information System (INIS)

Rajdeep; Mayya, Y.S.

2017-01-01

The safety of facilities in BARC is under the regulatory oversight of BSC. The security architecture for these facilities incorporates multiple layers of Physical Protection Systems. The demands of safety may sometimes conflict with the needs of security. Realizing the need to identify these interfaces and extend the regulatory coverage to Physical Protection Systems, a Standing Committee named Physical Protection System Review Committee (PPSRC) has been constituted as a 2"n"d tier entity of BSC. PPSRC includes experts from various domains concerned with nuclear security, viz. physical protection systems, cyber security, radiation safety, security operations, technical services and security administration

75 FR 40036 - Rehabilitation Research and Development Service Scientific Merit Review Board; Notice of Meeting

Science.gov (United States)

2010-07-13

... DEPARTMENT OF VETERANS AFFAIRS Rehabilitation Research and Development Service Scientific Merit... (Federal Advisory Committee Act) that the Rehabilitation Research and Development Service Scientific Merit... is to review rehabilitation research and development applications for scientific and technical merit...

Distributed Supervisory Protection Interlock System

International Nuclear Information System (INIS)

Walz, H.V.; Agostini, R.C.; Barker, L.; Cherkassky, R.; Constant, T.; Matheson, R.

1989-03-01

The Distributed Supervisory Protection Interlock System, DSPI, is under development at the Stanford Linear Accelerator Center for requirements in the areas of personnel protection, beam containment and equipment protection interlocks. The DSPI system, distributed over the application site, consists of segments with microprocessor-based controller and I/O modules, local area networks for communication, and a global supervisor computer. Segments are implemented with commercially available controller and I/O modules arranged in local interlock clusters, and associated software. Segments provide local interlock data acquisition, processing and control. Local area networks provide the communication backbone between segments and a global supervisor processor. The supervisor processor monitors the overall system, reports detail status and provides human interfaces. Details of an R and D test system, which will implement the requirements for personnel protection of 4 typical linear accelerator sectors, will be described. 4 refs., 2 figs

CERN's Merit Appraisal and Recognition System from the point of view of the supervisor

CERN Multimedia

CERN. Geneva

2013-01-01

The required training consists of 2 parts : This presentation explaining “CERN’s merit recognition system”, followed by a session of questions/answers – duration : 2 hours A training session on “How to get, as a supervisor, the most out of the annual interview” – duration : 1 day. This hands-on training focuses on how to set smart work and development objectives, how to give feedback and how to run the annual interview in a constructive way.

Power system protection 2 systems and methods

CERN Document Server

1995-01-01

The worldwide growth in demand for electricity has forced the pace of developments in electrical power system design to meet consumer needs for reliable, secure and cheap supplies. Power system protection, as a technology essential to high quality supply, is widely recognised as a specialism of growing and often critical importance, in which power system needs and technological progress have combined to result in rapid developments in policy and practice in recent years. In the United Kingdom, the need for appropriate training in power system protection was recognised in the early 1960s with t

Wind turbine with lightning protection system

DEFF Research Database (Denmark)

2016-01-01

The present invention relates to a wind turbine comprising a lightning protection system comprising a waveguide interconnecting a communication device and a signal-carrying structure. In other aspects, the present invention relates to the use of a waveguide in a lightning protection system...... of a wind turbine, a power splitter and its use in a lightning protection system of a wind turbine....

Figures of merit for measuring aging management program effectiveness

International Nuclear Information System (INIS)

Knudson, R.; Sciacca, F.; Walsh, R.; Zigler, G.

1991-01-01

One of the requirements for nuclear plant license renewal may be the establishment and demonstration of an effective aging management program. An analysis of both qualitative and quantitative information will be required to define the contents of this aging management program. The authors propose two quantitative figures of merit, Mean Event Detection Frequency and Mean Renewal Rate, that can be used to compare the effectiveness of various inspection, surveillance, test, and monitoring (ISTM) activities for aging mitigation. An example showing the relative effectiveness of an enhanced Loose Parts Monitoring System with current ISTM activities for steam generators and reactor internals is provided. (author)

75 FR 52749 - Privacy Act of 1974; System of Records Notices

Science.gov (United States)

2010-08-27

..., social security number and personal history. Records in this system are collected and generated during... working papers, draft materials, and other documents and records relating to the investigation... connection with EEO matters; to make reports to Office of Management and Budget, Merit Systems Protection...

Invisible in Thailand: documenting the need for protection

Directory of Open Access Journals (Sweden)

Margaret Green

2008-04-01

Full Text Available The International Rescue Committee (IRC has conducted asurvey to document the experiences of Burmese people livingin border areas of Thailand and assess the degree to whichthey merit international protection as refugees.

Design Of Photovoltaic Powered Cathodic Protection System

Directory of Open Access Journals (Sweden)

Golina Samir Adly

2017-07-01

Full Text Available The corrosion caused by chemical reaction between metallic structures and surrounding mediums such as soil or water .the CP cathodic protection system is used to protect metallic structure against corrosion. Cathodic protection CP used to minimize corrosion by utilizing an external source of electrical current which forces the entire structure to become a cathode. There are two Types of cathodic protection system Galvanic current Impressed current.the Galvanic current is called a sacrificial anode is connected to the protected structure cathode through a DC power supply. In Galvanic current system a current passes from the sacrificing anode to the protected structure .the sacrificial anode is corroded rather than causing the protected structure corrosion .protected structure requires a constant current to stop the corrosion which determined by area structure metal and the surrounding medium. The rains humidity are decrease soil resistivity and increase the DC current .The corrosion and over protection resulting from increase in the DC current is harmful for the metallic structure. This problem can be solved by conventional cathodic protection system by manual adjustment of DC voltage periodically to obtain a constant current .the manual adjustment of DC voltage depends on experience of the technician and using the accuracy of the measuring equipment. The errors of measuring current depend on error from the technician or error from the measuring equipment. the corrosion of structure may occur when the interval between two successive adjustment is long .An automatically regulated cathodic protection system is used to overcome problems from conventional cathodic protection system .the regulated cathodic protection system adjust the DC voltage of the system automatically when it senses the variations of surrounding medium resistivity so the DC current is constant at the required level.

Thermoelectric figure of merit of chiral carbon nanotube

International Nuclear Information System (INIS)

Mensah, N.G.; Nkrumah-Buandoh, G.K.; Mensah, S.Y.; Allotey, F.K.A.; Twum, A.K.

2005-09-01

We have investigated the thermoelectrical properties of chiral carbon nanotube and numerically evaluated the figure of merit. We observed that the properties are highly anisotropic and depend on the geometric chiral angle (GCA) θ h , temperature and the overlapping integrals (exchange energy) for the jumps along the tubular axis Δ z and the base helix Δ s . The thermopower α exhibited giant values with the peak occurring between 100 K and 150 K. The electron thermal conductivity showed unusually high value with the peaks shifting towards high temperature. We attribute the high peak values to electron-phonon interactions. Finally we noted that by changing the Δ s and Δ z it is possible to get a figure of merit greater than 1. (author)

Temporary physical protection systems

International Nuclear Information System (INIS)

Williams, J.D.; Gangel, D.J.; Madsen, R.W.

1991-01-01

Terrorism and other aspects of world political instability have created a high demand for temporary physical protection systems within the nuclear materials management community. They can be used when vehicles carrying important assets are away from their permanent fixed site location, around areas where experiments are being temporarily conducted, around construction areas and one portions of a fixed site physical security system which is temporarily inoperable. Physical security systems can be grouped into four categories: tactical, portable, semi-permanent, and fixed. The resources and experience gained at Sandia National Laboratories in over forty years of developing and implementing security systems for protecting nuclear weapons and fixed nuclear facilities is now being applied to temporary physical security systems. This paper emphasizes temporary physical security systems and their component parts that are presently available and identify additional system-subsystem objectives, requirements, and concepts

Identity management and witness protection system

OpenAIRE

Paunović, Saša; Starčević, Dušan; Nešić, Lazar

2013-01-01

The protection of participants in criminal proceedings is one of the most important tools for prosecution of war crimes and organized crime cases. The paper presents the basic characteristics and the importance of implementing the Program of protection in criminal proceedings, with emphasis on the protection system and management of identity. Special attention was paid to challenges facing the protection system in criminal proceedings and the management of identities, which are caused by the ...

78 FR 77574 - Protection System Maintenance Reliability Standard

Science.gov (United States)

2013-12-24

... commissioning of power system protection systems.\\55\\ NERC commits in its Comments to keep the Commission... commissioning of power system protection systems.\\62\\ As explained in the NOPR, our concern is with a protection... protection system, ``resulting in line relays being placed in service with the incorrect transformer ratio...

Digital protection in power plants. Electrical unit and line protection. Digital protection systems for NPP

International Nuclear Information System (INIS)

Kaczmarek, A.

2000-01-01

In this presentation author deals with the digital protection systems for nuclear power plants. The evolution of protection devices, protection concept for power plants, concept of functional redundancy, references for digital protection, benefits for the customer well as concept fault recorder are presented. (author)

Smart cathodic protection systems

NARCIS (Netherlands)

Polder, R.B.; Leggedoor, J.; Schuten, G.; Sajna, S.; Kranjc, A.

2010-01-01

Cathodic protection delivers corrosion protection in concrete structures exposed to aggressive environments, e.g. in de-icing salt and marine climates. Working lives of a large number of CP systems are at least more than 13 years and probably more than 25 years, provided a minimum level of

[Artificial intelligence] AI for protection systems

Energy Technology Data Exchange (ETDEWEB)

Aggarwal, R.; Johns, A.

1997-12-31

The reliable operation of large power systems with small stability margins is highly dependent on control systems and protection devices. Progress in the field of microprocessor systems and demanding requirements in respect of the performance of protective relays are the reasons for digital device applications to power system protection. The superiority of numeric protection over its analogue alternatives is attributed to such factors as accurate extraction of the fundamental voltage and current components through filtering, functional benefits resulting from multi-processor design and extensive self-monitoring, etc. However, all these reasons have not led to a major impact on speed, sensitivity and selectivity of primary protective relays, and the gains are only marginal; this is so because conventional digital relays still rely on deterministic signal models and a heuristic approach for decision making, so that only a fraction of the information contained within voltage and current signals as well as knowledge about the plant to be protected is used. The performance of digital relays may be substantially improved if the decision making is based on elements of artificial intelligence (AI). (Author)

Physical protection system design and evaluation

International Nuclear Information System (INIS)

Williams, J.D.

1997-11-01

The design of an effective physical protection system (PPS) includes the determination of the PPS objectives, the initial design of a PPS, the evaluation of the design, and probably, the redesign or refinement of the system. To develop the objectives, the designer must begin by gathering information about facility operation and conditions, such as a comprehensive description of the facility, operating conditions, and the physical protection requirements. The designer then needs to define the threat. This involves considering factors about potential adversaries: class of adversary, adversary's capabilities, and range of adversary's tactics. Next, the designer should identify targets. Determination of whether or not the materials being protected are attractive targets is based mainly on the ease or difficulty of acquisition and desirability of the material. The designer now knows the objectives of the PPS, that is, ''what to protect against whom.'' The next step is to design the system by determining how best to combine such elements as fences, vaults, sensors and assessment devices, entry control devices, communication devices, procedures, and protective force personnel to meet the objectives of the system. Once a PPS is designed, it must be analyzed and evaluated to ensure it meets the PPS objectives. Evaluation must allow for features working together to ensure protection rather than regarding each feature separately. Due to the complexity of the protection systems, an evaluation usually requires modeling techniques. If any vulnerabilities are found, the initial system must be redesigned to correct the vulnerabilities and a reevaluation conducted. After the system is installed, the threat and system parameters may change with time. If they do, the analysis must be performed periodically to ensure the system objectives are still being met

An integrated system for physical protection

International Nuclear Information System (INIS)

Kumar, Ranajit

2001-01-01

An Integrated Physical Protection System (IPPS) was developed for the consolidation of all sub systems, sensors and elements related to physical protection for an efficient and effective security environment of a facility. An effective physical protection system discharges the functions of detection, delay, communication, response, access control etc. IPPS performs, controls and monitors all the above functionality and helps in taking quick action on occurrence of unusual incidents by instantly reporting the incident in easily understandable audio, video, graphical and textual format and also by initiating automatic interactions among sub-systems

Reactor protection system. Revision 1

International Nuclear Information System (INIS)

Fairbrother, D.B.; Vincent, D.R.; Lesniak, L.M.

1975-04-01

The reactor protection system-II (RPS-II) designed for use on Babcock and Wilcox 145- and 205-fuel assembly pressurized water reactors is described. In this system, relays in the trip logic have been replaced by solid state devices. A calculating module for the low DNBR, pump status, and offset trip functions has replaced the overpower trip (based on flow and imbalance), the power/RC pump trip, and the variable low pressure trip. Included is a description of the changes from the present Oconee-type reactor protection system (RPS-I), a functional and hardware description of the calculating module, and a discussion of the qualification program conducted to ensure that the degree of protection provided by RPS-II is not less than that provided by previously licensed systems supplied by B and W. (U.S.)

The merit of synesthesia for consciousness research

Directory of Open Access Journals (Sweden)

Tessa Marije Van Leeuwen

2015-12-01

Full Text Available Synesthesia is a phenomenon in which additional perceptual experiences are elicited by sensory stimuli or cognitive concepts. Synesthetes possess a unique type of phenomenal experiences not directly triggered by sensory stimulation. Therefore, for better understanding of consciousness it is relevant to identify the mental and physiological processes that subserve synesthetic experience. In the present work we suggest several reasons why synesthesia has merit for research on consciousness. We first review the research on the dynamic and rapidly growing field of the studies of synesthesia. We particularly draw attention to the role of semantics in synesthesia, which is important for establishing synesthetic associations in the brain. We then propose that the interplay between semantics and sensory input in synesthesia can be helpful for the study of the neural correlates of consciousness, especially when making use of ambiguous stimuli for inducing synesthesia. Finally, synesthesia-related alterations of brain networks and functional connectivity can be of merit for the study of consciousness.

Advanced physical protection systems for nuclear materials

International Nuclear Information System (INIS)

Jones, O.E.

1976-01-01

Because of the increasing incidence of terrorism, there is growing concern that nuclear materials and facilities need improved physical protection against theft, diversion, or sabotage. Physical protection systems for facilities or transportation which have balanced effectiveness include information systems, access denial systems, adequate and timely response, recovery capability, and use denial methods for despoiling special nuclear materials (SNM). The role of these elements in reducing societal risk is described; however, it is noted that, similar to nuclear war, the absolute risks of nuclear theft and sabotage are basically unquantifiable. Sandia Laboratories has a major US Energy Research and Development Administration (ERDA) role in developing advanced physical protection systems for improving the security of both SNM and facilities. These activities are surveyed in this paper. A computer simulation model is being developed to assess the cost-effectiveness of alternative physical protection systems under various levels of threat. Improved physical protection equipment such as perimeter and interior alarms, secure portals, and fixed and remotely activated barriers is being developed and tested. In addition, complete prototype protection systems are being developed for representative nuclear facilities. An example is shown for a plutonium storage vault. The ERDA safe-secure transportation system for highway shipments of all significant quantities of government-owned SNM is described. Adversary simulation as a tool for testing and evaluating physical protection systems is discussed. Finally, a list of measures is given for assessing overall physical protection system performance. (author)

Advanced physical protection systems for nuclear materials

International Nuclear Information System (INIS)

Jones, O.E.

1975-10-01

Because of the increasing incidence of terrorism, there is growing concern that nuclear materials and facilities need improved physical protection against theft, diversion, or sabotage. Physical protection systems for facilities or transportation which have balanced effectiveness include information systems, access denial systems, adequate and timely response, recovery capability, and use denial methods for despoiling special nuclear materials (SNM). The role of these elements in reducing societal risk is described; however, it is noted that, similar to nuclear war, the absolute risks of nuclear theft and sabotage are basically unquantifiable. Sandia Laboratories has a major Energy Research and Development Administration (ERDA) role in developing advanced physical protection systems for improving the security of both SNM and facilities. These activities are surveyed. A computer simulation model is being developed to assess the cost-effectiveness of alternative physical protection systems under various levels of threat. Improved physical protection equipment such as perimeter and interior alarms, secure portals, and fixed and remotely-activated barriers is being developed and tested. In addition, complete prototype protection systems are being developed for representative nuclear facilities. An example is shown for a plutonium storage vault. The ERDA safe-secure transportation system for highway shipments of all significant quantities of government-owned SNM is described. Adversary simulation as a tool for testing and evaluating physical protection systems is discussed. A list of measures is given for assessing overall physical protection system performance. (auth)

Improved core protection calculator system algorithm

International Nuclear Information System (INIS)

Yoon, Tae Young; Park, Young Ho; In, Wang Kee; Bae, Jong Sik; Baeg, Seung Yeob

2009-01-01

Core Protection Calculator System (CPCS) is a digitized core protection system which provides core protection functions based on two reactor core operation parameters, Departure from Nucleate Boiling Ratio (DNBR) and Local Power Density (LPD). It generates a reactor trip signal when the core condition exceeds the DNBR or LPD design limit. It consists of four independent channels which adapted a two out of four trip logic. CPCS algorithm improvement for the newly designed core protection calculator system, RCOPS (Reactor COre Protection System), is described in this paper. New features include the improvement of DNBR algorithm for thermal margin, the addition of pre trip alarm generation for auxiliary trip function, VOPT (Variable Over Power Trip) prevention during RPCS (Reactor Power Cutback System) actuation and the improvement of CEA (Control Element Assembly) signal checking algorithm. To verify the improved CPCS algorithm, CPCS algorithm verification tests, 'Module Test' and 'Unit Test', would be performed on RCOPS single channel facility. It is expected that the improved CPCS algorithm will increase DNBR margin and enhance the plant availability by reducing unnecessary reactor trips

49 CFR 1103.19 - Advising upon the merits of a client's cause.

Science.gov (United States)

2010-10-01

... 49 Transportation 8 2010-10-01 2010-10-01 false Advising upon the merits of a client's cause. 1103... Practitioner's Duties and Responsibilities Toward A Client § 1103.19 Advising upon the merits of a client's cause. A practitioner shall try to obtain full knowledge of his client's cause before advising thereon...

Figures of merit for detectors in digital radiography. II. Finite number of secondaries and structured backgrounds

International Nuclear Information System (INIS)

Pineda, Angel R.; Barrett, Harrison H.

2004-01-01

The current paradigm for evaluating detectors in digital radiography relies on Fourier methods. Fourier methods rely on a shift-invariant and statistically stationary description of the imaging system. The theoretical justification for the use of Fourier methods is based on a uniform background fluence and an infinite detector. In practice, the background fluence is not uniform and detector size is finite. We study the effect of stochastic blurring and structured backgrounds on the correlation between Fourier-based figures of merit and Hotelling detectability. A stochastic model of the blurring leads to behavior similar to what is observed by adding electronic noise to the deterministic blurring model. Background structure does away with the shift invariance. Anatomical variation makes the covariance matrix of the data less amenable to Fourier methods by introducing long-range correlations. It is desirable to have figures of merit that can account for all the sources of variation, some of which are not stationary. For such cases, we show that the commonly used figures of merit based on the discrete Fourier transform can provide an inaccurate estimate of Hotelling detectability

78 FR 12422 - Health Services Research and Development Service Scientific Merit Review Board, Notice of Meeting

Science.gov (United States)

2013-02-22

... DEPARTMENT OF VETERANS AFFAIRS Health Services Research and Development Service Scientific Merit... nursing research. Applications are reviewed for scientific and technical merit, mission relevance, and the... Program Manager, Scientific Merit Review Board, Department of Veterans Affairs, Health Services Research...

Availability analysis of supervised protective systems

International Nuclear Information System (INIS)

Kontoleon, N.; Kontoleon, J.M.; Chrysochoides, N.G.

1975-01-01

The behaviour in time of a nuclear reactor supervised protective system is modelled mathematically by a Markov process, continuous in time and with three discrete states. Failure and repair rates are assumed to be exponentially distributed. An analytical expression of system availability as a function of failure and repair rates as well as the inspection intervals and duration is derived. An optimization problem is then discussed in order to maximize system availability with respect to imposed cost constraints. Finally, an example of a supervised protective system with short inactive times is given, which may be found in many practical situations of modern protective systems. (author)

The LHC quench protection system

CERN Multimedia

2009-01-01

The new quench protection system (QPS) has the crucial roles of providing an early warning for any part of the superconducting coils and busbars that develop high resistance, as well as triggering the switch-off of the machine. Over 2000 new detectors will be installed around the LHC to make sure every busbar segment between magnets is monitored and protected. One of the major consolidation activities for the LHC is the addition of two new detectors to the quench protection system. A magnet quench occurs when part of the superconducting cable becomes normally-conducting. When the protection system detects an increased resistance the huge amount of energy stored in the magnet chains is safely extracted and ‘dumped’ into specially designed resistors. In the case of the main dipole chain, the stored energy in a single LHC sector is roughly the same as the kinetic energy of a passenger jet at cruising speed. The first new detector is designed to monitor the superconducting...

Corrosion protection method by neutral treatment for boilers

International Nuclear Information System (INIS)

Ishikawa, Hisashige

1978-01-01

The corrosion protection method by neutral treatment has been applied in Europe mainly for boilers and nuclear reactors instead of existing all volatile treatment. The cause of corrosion of steel and copper in water and the effect of neutral treatment, that is the effect of protection film of magnetite in steel and cuprous oxide in copper alloy, are explained with the characteristic figure of PH, electromotive force and chemical formula. The experience of applying this neutral treatment to the Wedel thermal power plant and the system flow sheet, the water treatment equipment, relating instrumentations and the water examination are described in detail. Hydrogen peroxide is injected in this neutral treatment. The comparison between the existing water treatment and the neutral treatment and their merits and demerits are explained. (Nakai, Y.)

78 FR 6854 - Health Services Research and Development Service Scientific Merit Review Board; Notice of Meeting

Science.gov (United States)

2013-01-31

... DEPARTMENT OF VETERANS AFFAIRS Health Services Research and Development Service Scientific Merit... Research and Development Service Scientific Merit Review Board will meet on February 13-14, 2013, at the... research. Applications are reviewed for scientific and technical merit. Recommendations regarding funding...

Radiological protection system in the era of nuclear renaissance expectation for development of radiological protection system

International Nuclear Information System (INIS)

Toyomatsu, Hideki

2008-01-01

The current radiological protection system, which was established mainly by the ICRP and UNSCEAR, has contributed to the prevention of potential radiological health hazards, and has been a fundamental concept during the development of nuclear energy. Through a detailed discussion regarding the new ICRP recommendations, the world nuclear industry has reached a consensus that the current radiological protection system keeps its integrity in principle although it involves some remaining issues, such as the disposal of radioactive waste. In order to maximize the advantages of nuclear energy while keeping the integrity of radiological protection system, it is essential to address the characteristics of radiation, which is specific to nuclear energy, so that nuclear energy can coexist with other energy sources. The three basic principles of radiological protection (i.e., justification, optimization and dose limits), which were completed in the 1990 recommendations of ICRP, should be retained as the basic concepts for the future radiological protection system in order to maintain the continuity and consistency of the radiological protection system. The radiological protection system can be furthermore developed only by combining the above three principles with best practices extracted from utilities' field experience. The significant reduction of radiation exposures received by members of the public and radiation workers in the field has resulted from the efforts by the world utilities to achieve the optimization. In order to correctly apply the theory to the work practices, it is essential to see how the theory is practically used in the field. Such a process should be also emphasized in the revision work of the IAEA Basic Safety Standards (BSS), which is currently under progress. Integrating the theory in the work practices is the key to the true development of nuclear renaissance, which could lead to the establishment of the nuclear safety regime. (author)

Risk Aversion and Support for Merit Pay: Theory and Evidence from Minnesota's Q Comp Program

Science.gov (United States)

Nadler, Carl; Wiswall, Matthew

2011-01-01

Recent research attributes the lack of merit pay in teaching to the resistance of teachers. This article examines whether the structure of merit pay affects the types of teachers who support it. We develop a model of the relative utility teachers receive from merit pay versus the current fixed schedule of raises. We show that if teachers are risk…

Power system protection 3 application

CERN Document Server

1995-01-01

The worldwide growth in demand for electricity has forced the pace of developments in electrical power system design to meet consumer needs for reliable, secure and cheap supplies. Power system protection, as a technology essential to high quality supply, is widely recognised as a specialism of growing and often critical importance, in which power system needs and technological progress have combined to result in rapid developments in policy and practice in recent years. In the United Kingdom, the need for appropriate training in power system protection was recognised in the early 1960s with t

High figure-of-merit SOI power LDMOS for power integrated circuits

Directory of Open Access Journals (Sweden)

Yashvir Singh

2015-06-01

Full Text Available The structural modifications in the conventional power laterally diffused metal-oxide-semiconductor field-effect transistor (LDMOS are carried out to improve the breakdown voltage, on-resistance, gate-charge and figure-of-merits of the device with reduced cell pitch. The modified device has planer structure implemented on silicon-on-insulator which is suitable for low to medium voltage power integrated circuits. The proposed LDMOS consists of two gate electrodes placed vertically in two separate trenches build in the drift region and single source and drain contacts are taken on the top. The trench structure reduces the electric field inside the drift region and allow increased drift layer doping concentration leading to higher breakdown voltage, lower specific on-resistance, reduced gate-drain charge, and substantial improvement in the figure-of-merits. Using two-dimensional simulations, the performance of the proposed LDMOS is optimized and results are compared with the conventional LDMOS. Our simulation results show that the proposed device exhibits 110% higher breakdown voltage, 40% reduction in cell pitch, 19% lower specific on-resistance, 30% lower gate-to-drain charge leading to 5.5 times improvement in Baliga's figure-of-merit and 43% reduction in dynamic figure-of-merit over the conventional device.

46 CFR 153.460 - Fire protection systems.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Fire protection systems. 153.460 Section 153.460... Requirements for Flammable Or Combustible Cargoes § 153.460 Fire protection systems. Each self-propelled ship... protection system listed beside the cargo in Table 1 and described in the footnotes to Table 1. (b) The...

WASTE HANDLING BUILDING FIRE PROTECTION SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

J. D. Bigbee

2000-06-21

The Waste Handling Building Fire Protection System provides the capability to detect, control, and extinguish fires and/or mitigate explosions throughout the Waste Handling Building (WHB). Fire protection includes appropriate water-based and non-water-based suppression, as appropriate, and includes the distribution and delivery systems for the fire suppression agents. The Waste Handling Building Fire Protection System includes fire or explosion detection panel(s) controlling various detectors, system actuation, annunciators, equipment controls, and signal outputs. The system interfaces with the Waste Handling Building System for mounting of fire protection equipment and components, location of fire suppression equipment, suppression agent runoff, and locating fire rated barriers. The system interfaces with the Waste Handling Building System for adequate drainage and removal capabilities of liquid runoff resulting from fire protection discharges. The system interfaces with the Waste Handling Building Electrical Distribution System for power to operate, and with the Site Fire Protection System for fire protection water supply to automatic sprinklers, standpipes, and hose stations. The system interfaces with the Site Fire Protection System for fire signal transmission outside the WHB as needed to respond to a fire emergency, and with the Waste Handling Building Ventilation System to detect smoke and fire in specific areas, to protect building high-efficiency particulate air (HEPA) filters, and to control portions of the Waste Handling Building Ventilation System for smoke management and manual override capability. The system interfaces with the Monitored Geologic Repository (MGR) Operations Monitoring and Control System for annunciation, and condition status.

WASTE HANDLING BUILDING FIRE PROTECTION SYSTEM DESCRIPTION DOCUMENT

International Nuclear Information System (INIS)

J. D. Bigbee

2000-01-01

The Waste Handling Building Fire Protection System provides the capability to detect, control, and extinguish fires and/or mitigate explosions throughout the Waste Handling Building (WHB). Fire protection includes appropriate water-based and non-water-based suppression, as appropriate, and includes the distribution and delivery systems for the fire suppression agents. The Waste Handling Building Fire Protection System includes fire or explosion detection panel(s) controlling various detectors, system actuation, annunciators, equipment controls, and signal outputs. The system interfaces with the Waste Handling Building System for mounting of fire protection equipment and components, location of fire suppression equipment, suppression agent runoff, and locating fire rated barriers. The system interfaces with the Waste Handling Building System for adequate drainage and removal capabilities of liquid runoff resulting from fire protection discharges. The system interfaces with the Waste Handling Building Electrical Distribution System for power to operate, and with the Site Fire Protection System for fire protection water supply to automatic sprinklers, standpipes, and hose stations. The system interfaces with the Site Fire Protection System for fire signal transmission outside the WHB as needed to respond to a fire emergency, and with the Waste Handling Building Ventilation System to detect smoke and fire in specific areas, to protect building high-efficiency particulate air (HEPA) filters, and to control portions of the Waste Handling Building Ventilation System for smoke management and manual override capability. The system interfaces with the Monitored Geologic Repository (MGR) Operations Monitoring and Control System for annunciation, and condition status

Minimización de una función normal-merit mediante un algoritmo convergente globalmente

Directory of Open Access Journals (Sweden)

Gómez Suárez, M.

1998-01-01

Full Text Available En este trabajo presentamos dos conceptos relacionados con la solución de sistemas de ecuaciones no lineales y con desigualdades. El primer concepto es el de una función normal merit, que resume las propiedades básicas que tienen distintas funciones merit conocidas. El segundo concepto es el de un operador Newtoniano, cuyos valores generalizan el concepto de Hessiana para la función normal merit. Combinando el resultado del método generalizado de Newton con ciertos métodos de primer orden, obtenemos un algoritmo de convergencia global para minimizar funciones normales merit.

2015 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

none,

2015-10-01

This report summarizes comments from the Peer Review Panel at the 2015 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on June 8-12, 2015, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; market transformation; and systems analysis.

2011 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

none,

2011-09-01

This report summarizes comments from the Peer Review Panel at the 2011 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on May 9-13, 2011, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; education; market transformation; and systems analysis.

2013 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

none,

2013-10-01

This report summarizes comments from the Peer Review Panel at the 2013 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on May 13-17, 2013, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; market transformation; and systems analysis.

2014 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

none,

2014-10-01

This report summarizes comments from the Peer Review Panel at the 2014 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on June 16-20, 2014, in Washington, DC. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; market transformation; and systems analysis.

2012 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

none,

2012-09-01

This report summarizes comments from the Peer Review Panel at the 2012 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on May 14-18, 2012, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; education; market transformation; and systems analysis.

5 CFR 335.106 - Special selection procedures for certain veterans under merit promotion.

Science.gov (United States)

2010-01-01

... veterans under merit promotion. 335.106 Section 335.106 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PROMOTION AND INTERNAL PLACEMENT General Provisions § 335.106 Special selection procedures for certain veterans under merit promotion. Preference eligibles or veterans who have...

Merit-order effects of renewable energy and price divergence in California’s day-ahead and real-time electricity markets

International Nuclear Information System (INIS)

Woo, C.K.; Moore, J.; Schneiderman, B.; Ho, T.; Olson, A.; Alagappan, L.; Chawla, K.; Toyama, N.; Zarnikau, J.

2016-01-01

We answer two policy questions: (1) what are the estimated merit-order effects of renewable energy in the California Independent System Operator’s (CAISO’s) day-ahead market (DAM) and real-time market (RTM)? and (2) what causes the hourly DAM and RTM prices to systematically diverge? The first question is timely and relevant because if the merit-order effect estimates are small, California’s renewable energy development is of limited help in cutting electricity consumers’ bills but also has a lesser adverse impact on the state’s investment incentive for natural-gas-fired generation. The second question is related to the efficient market hypothesis under which the hourly RTM and DAM prices tend to converge. Using a sample of about 21,000 hourly observations of CAISO market prices and their fundamental drivers during 12/12/2012–04/30/2015, we document statistically significant estimates (p-value≤0.01) for the DAM and RTM merit-order effects. This finding lends support to California’s adopted procurement process to provide sufficient investment incentives for natural-gas-fired generation. We document that the RTM-DAM price divergence partly depends on the CASIO’s day-ahead forecast errors for system loads and renewable energy. This finding suggests that improving the performance of the CAISO’s day-ahead forecasts can enhance trading efficiency in California’s DAM and RTM electricity markets. - Highlights: •Estimate the day-ahead and real-time merit-order effects of renewable energy in California. •Document statistically significant merit-order effects of solar and wind energy. •Document the difference between the day-ahead and real-time prices. •Attribute the price differences to forecast errors for load, solar and wind energy. •Discuss the evidence’s implications for California’s energy policy.

Advanced worker protection system

International Nuclear Information System (INIS)

Caldwell, B.; Duncan, P.; Myers, J.

1995-01-01

The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D ampersand D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D ampersand D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D ampersand D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project will result in the development of an Advanced Worker Protection System (AWPS). The AWPS will be built around a life support backpack that uses liquid air to provide cooling as well as breathing gas to the worker. The backpack will be combined with advanced protective garments, advanced liquid cooling garment, respirator, communications, and support equipment to provide improved worker protection, simplified system maintenance, and dramatically improve worker productivity through longer duration work cycles. Phase I of the project has resulted in a full scale prototype Advanced Worker Protection Ensemble (AWPE, everything the worker will wear), with sub-scale support equipment, suitable for integrated testing and preliminary evaluation. Phase II will culminate in a full scale, certified, pre-production AWPS and a site demonstration

Advanced worker protection system

Energy Technology Data Exchange (ETDEWEB)

Caldwell, B.; Duncan, P.; Myers, J.

1995-12-01

The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D&D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D&D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D&D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project will result in the development of an Advanced Worker Protection System (AWPS). The AWPS will be built around a life support backpack that uses liquid air to provide cooling as well as breathing gas to the worker. The backpack will be combined with advanced protective garments, advanced liquid cooling garment, respirator, communications, and support equipment to provide improved worker protection, simplified system maintenance, and dramatically improve worker productivity through longer duration work cycles. Phase I of the project has resulted in a full scale prototype Advanced Worker Protection Ensemble (AWPE, everything the worker will wear), with sub-scale support equipment, suitable for integrated testing and preliminary evaluation. Phase II will culminate in a full scale, certified, pre-production AWPS and a site demonstration.

Improved merit order and augmented Lagrange Hopfield network for short term hydrothermal scheduling

International Nuclear Information System (INIS)

Vo Ngoc Dieu; Ongsakul, Weerakorn

2009-01-01

This paper proposes an improved merit order (IMO) combined with an augmented Lagrangian Hopfield network (ALHN) for solving short term hydrothermal scheduling (HTS) with pumped-storage hydro plants. The proposed IMO-ALHN consists of a merit order based on the average production cost of generating units enhanced by heuristic search algorithm for finding unit scheduling and a continuous Hopfield neural network with its energy function based on augmented Lagrangian relaxation for solving constrained economic dispatch (CED). The proposed method is applied to solve the HTS problem in five stages including thermal, hydro and pumped-storage unit commitment by IMO and heuristic search, constraint violations repairing by heuristic search and CED by ALHN. The proposed method is tested on the 24-bus IEEE RTS with 32 units including 4 fuel-constrained, 4-hydro, and 2 pumped-storage units scheduled over a 24-h period. Test results indicate that the proposed IMO-ALHN is efficient for hydrothermal systems with various constraints.

EMP protection procedure for electrical/electronic systems

International Nuclear Information System (INIS)

Latorre, V.R.

1976-01-01

This paper presents a procedure for the protection engineer to follow in assessing a system with respect to its susceptibility to an electromagnetic pulse (EMP), and in determining whether the system requires protection. If the system is determined to be vulnerable to EMP, the procedure also indicates how to decide upon the most suitable protection scheme. The discussion centers on two flow charts, which illustrate the step-by-step procedure which utilizes the necessary ingredients of EMP protection engineering discussed in a previous paper. The description of the protection procedure is divided into two parts: the first dealing with issues on the macroscopic or large-scale system level, while the second is concerned with operations on the subsystem level or lower

Sandia Laboratories plutonium protection system

International Nuclear Information System (INIS)

Bernard, E.A.; Miyoshi, D.S.; Gutierrez, F.D.

1977-01-01

Sandia Laboratories is developing an improved plutonium protection system (PPS) to demonstrate new concepts for enhancing special nuclear materials safeguards. PPS concepts include separation of functions, real-time item accountability and improved means for control of materials, activities and personnel access. Physical barriers and a secure communications network are designed into the system to offer greater protection against sabotage, diversion and theft attempts. Prototype systems are being constructed at Hanford, Washington and Albuquerque, New Mexico and will be subjected to a comprehensive testing and evaluation program

The Diamond machine protection system

International Nuclear Information System (INIS)

Heron, M.T.; Lay, S.; Chernousko, Y.; Hamadyk, P.; Rotolo, N.

2012-01-01

The Diamond Light Source Machine Protection System (MPS) manages the hazards from high power photon beams and other hazards to ensure equipment protection on the booster synchrotron and storage ring. The system has a shutdown requirement, on a beam mis-steer of under 1 msec and has to manage in excess of a thousand interlocks. This is realised using a combination of bespoke hardware and programmable logic controllers. The MPS monitors a large number of interlock signals from diagnostics instrumentation, vacuum instrumentation, photon front ends and plant monitoring subsystems. Based on logic it can then remove the source of the energy to ensure protection of equipment. Depending on requirements, interlocks are managed on a Local or a Global basis. The Global system is structured as two layers, and supports fast- and slow-response-time interlock requirements. A Global MPS module takes the interlock permits for a given interlock circuit from each of the cells of the accelerator, and, subject to all interlocks being good, produces a permit to operate the source of energy: the RF amplifier for vessel protection and the PSU for magnet protection. The Local MPS module takes fast Interlock inputs from one cell of the Storage Ring or one quadrant of the Booster. Fast interlocks are those that must drop the beam in under 400 μsec (the maximum speed of the interlock) in the event of failure. EPIC provides the user interface to the MPS system

Reactor protection system design using micro-computers

International Nuclear Information System (INIS)

Fairbrother, D.B.

1977-01-01

Reactor Protection Systems for Nuclear Power Plants have traditionally been built using analog hardware. This hardware works quite well for single parameter trip functions; however, optimum protection against DNBR and KW/ft limits requires more complex trip functions than can easily be handled with analog hardware. For this reason, Babcock and Wilcox has introduced a Reactor Protection System, called the RPS-II, that utilizes a micro-computer to handle the more complex trip functions. This paper describes the design of the RPS-II and the operation of the micro-computer within the Reactor Protection System

Reactor protection system design using micro-computers

International Nuclear Information System (INIS)

Fairbrother, D.B.

1976-01-01

Reactor protection systems for nuclear power plants have traditionally been built using analog hardware. This hardware works quite well for single parameter trip functions; however, optimum protection against DNBR and KW/ft limits requires more complex trip functions than can easily be handled with analog hardware. For this reason, Babcock and Wilcox has introduced a Reactor Protection System, called the RPS-II, that utilizes a micro-computer to handle the more complex trip functions. The paper describes the design of the RPS-II and the operation of the micro-computer within the Reactor Protection System

Comparison, with regard to safety, between a hard-wired reactor protection system and a computerized protection system. Pt. 1

International Nuclear Information System (INIS)

Buettner, W.E.

1976-07-01

The study compares a conventional hard-wired dynamic reactor protection system with a computerized protection system. In the comparison, only the unequivocally safety-oriented protection actions are considered. In the first part, the different structures of both systems and the method of verification for their functional safety will be described. In the second part, the mean unavailability in case of demand for both systems under defined conditions will be determined. (orig.) [de

Management information system on radiation protection

Energy Technology Data Exchange (ETDEWEB)

Grossi, Pablo Andrade; Souza, Leonardo Soares de; Figueiredo, Geraldo Magela, E-mail: pabloag@cdtn.b, E-mail: lss@cdtn.b, E-mail: gmf@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2011-07-01

Considering the flux complexity and the multi source information of all radiation protection activities on nuclear organizations, an effective management information system based on technology, information and people is necessary to improve the safety on all processes and operations subjected to radiation risks. An effective management information system is an essential tool to highlight the strengths and weaknesses and identify behaviors and trends on the activities requiring radiation protection programs. Such kind of distinct knowledge is useful to reach an effective management and support the human decision-making on nuclear organization. This paper presents a management information system based on Brazilian directives and regulations on radiation protection. Due to its generic characteristics, this radiation protection control system can be implemented on any nuclear organization by reediting the non restricted parameters which could differ considering all facilities and laboratories expected on-site with diverse technologies applications. This system can be considered as a powerful tool applied on the continuous management of radiation protection activities on nuclear organizations and research institutes as well as for long term planning, not only indicating how the safety activities are going, but why they are not going as well as planned where that is the case. (author)

Management information system on radiation protection

International Nuclear Information System (INIS)

Grossi, Pablo Andrade; Souza, Leonardo Soares de; Figueiredo, Geraldo Magela

2011-01-01

Considering the flux complexity and the multi source information of all radiation protection activities on nuclear organizations, an effective management information system based on technology, information and people is necessary to improve the safety on all processes and operations subjected to radiation risks. An effective management information system is an essential tool to highlight the strengths and weaknesses and identify behaviors and trends on the activities requiring radiation protection programs. Such kind of distinct knowledge is useful to reach an effective management and support the human decision-making on nuclear organization. This paper presents a management information system based on Brazilian directives and regulations on radiation protection. Due to its generic characteristics, this radiation protection control system can be implemented on any nuclear organization by reediting the non restricted parameters which could differ considering all facilities and laboratories expected on-site with diverse technologies applications. This system can be considered as a powerful tool applied on the continuous management of radiation protection activities on nuclear organizations and research institutes as well as for long term planning, not only indicating how the safety activities are going, but why they are not going as well as planned where that is the case. (author)

Reactions to merit pay increases: a longitudinal test of a signal sensitivity perspective.

Science.gov (United States)

Shaw, Jason D; Duffy, Michelle K; Mitra, Atul; Lockhart, Daniel E; Bowler, Matthew

2003-06-01

The relationships among merit pay raises, trait positive affectivity (PA), and reactions to merit pay increases (pay attitudes and behavioral intentions) were explored in a longitudinal study of hospital employees. Drawing on signal sensitivity theory, the authors expected that PA would moderate the relationship between merit pay raise size and reactions to the increase such that pay raise size would be more strongly related to pay attitudes and behavioral intentions among those low in PA. Results strongly supported the predictions in the case of reactions to the raise amount (happiness and effort intentions) but not for pay level satisfaction. Implications of the results and directions for future research are identified.

Policy Perspectives: No Merit in these Scholarships

Science.gov (United States)

Vincent, Fay

2005-01-01

Mr. Fay Vincent, former Commissioner of Major League Baseball and Executive Vice President of The Coca Cola Company, provides a crisp, concise assessment of a trend that has worried us for quite a while: the growing trend of rewarding academically-gifted and typically-affluent students with an extra dose of merit aid, often at the expense of…

The Impact of Merit Pay on Teaching and Research Outcomes of Accounting Programs

Science.gov (United States)

Lindsay, David H.; Campbell, Annhenrie; Tan, Kim B.

2012-01-01

Basing the compensation of accounting professors on merit pay in order to encourage better teaching, research and service is controversial. This study uses data from a survey of the 852 accounting programs in the United States to empirically examine the influence of merit-based salary plans. Findings indicate a strong positive association between…

Advanced Protection & Service Restoration for FREEDM Systems

Science.gov (United States)

Singh, Urvir

A smart electric power distribution system (FREEDM system) that incorporates DERs (Distributed Energy Resources), SSTs (Solid State Transformers - that can limit the fault current to two times of the rated current) & RSC (Reliable & Secure Communication) capabilities has been studied in this work in order to develop its appropriate protection & service restoration techniques. First, a solution is proposed that can make conventional protective devices be able to provide effective protection for FREEDM systems. Results show that although this scheme can provide required protection but it can be quite slow. Using the FREEDM system's communication capabilities, a communication assisted Overcurrent (O/C) protection scheme is proposed & results show that by using communication (blocking signals) very fast operating times are achieved thereby, mitigating the problem of conventional O/C scheme. Using the FREEDM System's DGI (Distributed Grid Intelligence) capability, an automated FLISR (Fault Location, Isolation & Service Restoration) scheme is proposed that is based on the concept of 'software agents' & uses lesser data (than conventional centralized approaches). Test results illustrated that this scheme is able to provide a global optimal system reconfiguration for service restoration.

75 FR 65404 - Rehabilitation Research and Development Service Scientific Merit Review Board; Notice of Meeting

Science.gov (United States)

2010-10-22

... DEPARTMENT OF VETERANS AFFAIRS Rehabilitation Research and Development Service Scientific Merit... & Regenerative Medicine Subcommittee of the Rehabilitation Research and Development Service Scientific Merit..., examination, reference to, [[Page 65405

The merits of a robot : A Dutch experience

NARCIS (Netherlands)

Mobach, M.P.

2006-01-01

Purpose: To determine the merits of a robot at the community pharmacy in a quasi-experiment. Method: The applied methods for data-collection were barcode-time measurements, direct observations, time-interval studies, and tally at a Dutch community pharmacy. The topics consisted of workload, waiting

2009 DOE Vehicle Technologies Program Annual Merit Review

Energy Technology Data Exchange (ETDEWEB)

none,

2009-10-01

Annual Merit Review and Peer Evaluation Meeting to review the FY2008 accomplishments and FY2009 plans for the Vehicle Technologies Program, and provide an opportunity for industry, government, and academic to give inputs to DOE on the Program with a structured and formal methodology.

Relative Merits of Four Methods for Scoring Cloze Tests.

Science.gov (United States)

Brown, James Dean

1980-01-01

Describes study comparing merits of exact answer, acceptable answer, clozentropy and multiple choice methods for scoring tests. Results show differences among reliability, mean item facility, discrimination and usability, but not validity. (BK)

A reference model for model-based design of critical infrastructure protection systems

Science.gov (United States)

Shin, Young Don; Park, Cheol Young; Lee, Jae-Chon

2015-05-01

Today's war field environment is getting versatile as the activities of unconventional wars such as terrorist attacks and cyber-attacks have noticeably increased lately. The damage caused by such unconventional wars has also turned out to be serious particularly if targets are critical infrastructures that are constructed in support of banking and finance, transportation, power, information and communication, government, and so on. The critical infrastructures are usually interconnected to each other and thus are very vulnerable to attack. As such, to ensure the security of critical infrastructures is very important and thus the concept of critical infrastructure protection (CIP) has come. The program to realize the CIP at national level becomes the form of statute in each country. On the other hand, it is also needed to protect each individual critical infrastructure. The objective of this paper is to study on an effort to do so, which can be called the CIP system (CIPS). There could be a variety of ways to design CIPS's. Instead of considering the design of each individual CIPS, a reference model-based approach is taken in this paper. The reference model represents the design of all the CIPS's that have many design elements in common. In addition, the development of the reference model is also carried out using a variety of model diagrams. The modeling language used therein is the systems modeling language (SysML), which was developed and is managed by Object Management Group (OMG) and a de facto standard. Using SysML, the structure and operational concept of the reference model are designed to fulfil the goal of CIPS's, resulting in the block definition and activity diagrams. As a case study, the operational scenario of the nuclear power plant while being attacked by terrorists is studied using the reference model. The effectiveness of the results is also analyzed using multiple analysis models. It is thus expected that the approach taken here has some merits

Reactor protection systems of 500 MWe PHWRs

Energy Technology Data Exchange (ETDEWEB)

Mallik, G; Kelkar, M G; Apte, Ravindra [C and I Group, Nuclear Power Corporation, Mumbai (India)

1997-03-01

The 500 MWe PHWR has two totally independent, diverse, fast acting shutdown system called Shutdown System 1 (SDS 1) and Shutdown System 2 (SDS 2). The trip generation circuitry of SDS 1 and SDS 2 are known as Reactor Protection System 1 (RPS 1) and Reactor Protection System 2 (RPS 2) respectively. Some of the features specific to 500 MWe reactors are Core Over Power Protection System (COPPS) based upon in core Self Powered Neutron Detector (SPND) signals, use of local two out of three coincidence logic and adoption of overlap testing for RPS 2, use of Fine Impulse Testing (FIT) in RPS 2, testing of the final control elements namely electro-magnetic clutch of individual Shutoff Rods (SRs) of SDS 1 and all the fast acting valves of SDS 2, etc. The two shutdown systems have totally separate sets of sensors and associated signal processing circuitry as well as physical arrangements. A separate computerised test and monitoring unit is used for each of the two shutdown systems. Use of Programmable Digital Comparator (PDC) unit exclusively for reactor protection systems, has been adopted. The capability of PDC unit is enhanced and communication links are provided for its integration in over all system. The paper describes the design features of reactor protection systems. (author). 3 refs., 7 figs., 3 tabs.

HIV / AIDS prevalence testing - merits, methodology and outcomes ...

African Journals Online (AJOL)

HIV / AIDS prevalence testing - merits, methodology and outcomes of a survey conducted at a large mining organisation in South Africa. ... These baseline prevalence data also provide an opportunity for monitoring of proposed interventions using cross-sectional surveys at designated intervals in the future. South African ...

Controls and Machine Protection Systems

CERN Document Server

Carrone, E.

2016-01-01

Machine protection, as part of accelerator control systems, can be managed with a 'functional safety' approach, which takes into account product life cycle, processes, quality, industrial standards and cybersafety. This paper will discuss strategies to manage such complexity and the related risks, with particular attention to fail-safe design and safety integrity levels, software and hardware standards, testing, and verification philosophy. It will also discuss an implementation of a machine protection system at the SLAC National Accelerator Laboratory's Linac Coherent Light Source (LCLS).

Foundations for Protecting Renewable-Rich Distribution Systems.

Energy Technology Data Exchange (ETDEWEB)

Ellis, Abraham [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Brahma, Sukumar [New Mexico State Univ., Las Cruces, NM (United States); Ranade, Satish [New Mexico State Univ., Las Cruces, NM (United States)

2016-11-01

High proliferation of Inverter Interfaced Distributed Energy Resources (IIDERs) into the electric distribution grid introduces new challenges to protection of such systems. This is because the existing protection systems are designed with two assumptions: 1) system is single-sourced, resulting in unidirectional fault current, and (2) fault currents are easily detectable due to much higher magnitudes compared to load currents. Due to the fact that most renewables interface with the grid though inverters, and inverters restrict their current output to levels close to the full load currents, both these assumptions are no longer valid - the system becomes multi-sourced, and overcurrent-based protection does not work. The primary scope of this study is to analyze the response of a grid-tied inverter to different faults in the grid, leading to new guidelines on protecting renewable-rich distribution systems.

ADVANCED WORKER PROTECTION SYSTEM

International Nuclear Information System (INIS)

Judson Hedgehock

2001-01-01

From 1993 to 2000, OSS worked under a cost share contract from the Department of Energy (DOE) to develop an Advanced Worker Protection System (AWPS). The AWPS is a protective ensemble that provides the user with both breathing air and cooling for a NIOSH-rated duration of two hours. The ensemble consists of a liquid air based backpack, a Liquid Cooling Garment (LCG), and an outer protective garment. The AWPS project was divided into two phases. During Phase 1, OSS developed and tested a full-scale prototype AWPS. The testing showed that workers using the AWPS could work twice as long as workers using a standard SCBA. The testing also provided performance data on the AWPS in different environments that was used during Phase 2 to optimize the design. During Phase 1, OSS also performed a life-cycle cost analysis on a representative clean up effort. The analysis indicated that the AWPS could save the DOE millions of dollars on D and D activities and improve the health and safety of their workers. During Phase 2, OSS worked to optimize the AWPS design to increase system reliability, to improve system performance and comfort, and to reduce the backpack weight and manufacturing costs. To support this design effort, OSS developed and tested several different generations of prototype units. Two separate successful evaluations of the ensemble were performed by the International Union of Operation Engineers (IUOE). The results of these evaluations were used to drive the design. During Phase 2, OSS also pursued certifying the AWPS with the applicable government agencies. The initial intent during Phase 2 was to finalize the design and then to certify the system. OSS and Scott Health and Safety Products teamed to optimize the AWPS design and then certify the system with the National Institute of Occupational Health and Safety (NIOSH). Unfortunately, technical and programmatic difficulties prevented us from obtaining NIOSH certification. Despite the inability of NIOSH to certify

ADVANCED WORKER PROTECTION SYSTEM

Energy Technology Data Exchange (ETDEWEB)

Judson Hedgehock

2001-03-16

From 1993 to 2000, OSS worked under a cost share contract from the Department of Energy (DOE) to develop an Advanced Worker Protection System (AWPS). The AWPS is a protective ensemble that provides the user with both breathing air and cooling for a NIOSH-rated duration of two hours. The ensemble consists of a liquid air based backpack, a Liquid Cooling Garment (LCG), and an outer protective garment. The AWPS project was divided into two phases. During Phase 1, OSS developed and tested a full-scale prototype AWPS. The testing showed that workers using the AWPS could work twice as long as workers using a standard SCBA. The testing also provided performance data on the AWPS in different environments that was used during Phase 2 to optimize the design. During Phase 1, OSS also performed a life-cycle cost analysis on a representative clean up effort. The analysis indicated that the AWPS could save the DOE millions of dollars on D and D activities and improve the health and safety of their workers. During Phase 2, OSS worked to optimize the AWPS design to increase system reliability, to improve system performance and comfort, and to reduce the backpack weight and manufacturing costs. To support this design effort, OSS developed and tested several different generations of prototype units. Two separate successful evaluations of the ensemble were performed by the International Union of Operation Engineers (IUOE). The results of these evaluations were used to drive the design. During Phase 2, OSS also pursued certifying the AWPS with the applicable government agencies. The initial intent during Phase 2 was to finalize the design and then to certify the system. OSS and Scott Health and Safety Products teamed to optimize the AWPS design and then certify the system with the National Institute of Occupational Health and Safety (NIOSH). Unfortunately, technical and programmatic difficulties prevented us from obtaining NIOSH certification. Despite the inability of NIOSH to certify

78 FR 18680 - Rehabilitation Research and Development Scientific Merit Review Board, Notice of Meeting

Science.gov (United States)

2013-03-27

... DEPARTMENT OF VETERANS AFFAIRS Rehabilitation Research and Development Scientific Merit Review... Service, and the Chief Research and Development Officer on the scientific and technical merit, the mission... Committee Act, 5 U.S.C. App. 2, that a meeting of the Rehabilitation Research and Development Service...

Explosion-protected electric heating systems

Energy Technology Data Exchange (ETDEWEB)

Elsner, H

1984-02-01

Different constructions of explosion-protected heating systems are described concerning the different types of protection, the service conditions, the installation and the surveillance devices. Interpretations and regulations derived from the VDE Standards are discussed and their relation to the European Standards EN 50014 ... 50020 is considered in a survey.

The protection system to Brazilian Nuclear Program

International Nuclear Information System (INIS)

Andreuzza, Mario Giussepp Santezzi Bertottelli

1997-01-01

The Sistema de Protecao ao Programa Nuclear Brasileiro-SIPRON (Protection System to Brazilian Nuclear Program) was established in 1980. It is intended to accomplish in only one system, all the actions related to security and protection for Nuclear Facilities in Brazil. The author presents in detail the protection system SIPRON, describing the system structure and organization, the functions and obligations of the system involved main organizations, as well as, the system operation and behaviour during an postulated occurrence of a nuclear emergency. It is also described an Exercise that happened in June of 1997 at the Nuclear Power Plant (NPP) Angra I, after two simulated tests in December of 1996 and April of 1997. The NPP Angra I Emergency Plan Exercise was a good opportunity to test the SIPRON structure and preparedness program. It was verified, included by International Atomic Energy Agency observers, the system involved organizations effectiveness and the procedures efficacy to protect the public and the environmental. Finally, it is shown the SIPRON activities of routine, the system obstacles and the expected future performances. (author)

Performance Appraisal and Merit Compensation. Community Colleges: Quality Education for a Learning Society. Round Table Talk.

Science.gov (United States)

Anderson, Robert A., Jr.

Detailed information is provided on the Performance Appraisal/Salary System adopted by the New Mexico Junior College (NMJC) Board in 1981 as the basis for the performance evaluation of all college employees. Introductory material discusses the concepts of performance appraisal and merit compensation and provides an update on changes in NMJC's…

The APS machine protection system (MPS)

Energy Technology Data Exchange (ETDEWEB)

Fuja, R.; Berg, B.; Arnold, N. [and others

1996-08-01

The machine protection system (MPS) that protects the APS storage ring vacuum chamber from x-ray beams, is active. There are over 650 sensors monitored and networked through the MPS system. About the same number of other process variables are monitored by the much slower EPICS control system, which also has an input to the rf abort chain. The MPS network is still growing with the beam position limits detection system coming on-line. The network configuration, along with a limited description of individual subsystems, is presented.

The APS machine protection system (MPS)

International Nuclear Information System (INIS)

Fuja, R.; Berg, B.; Arnold, N.

1996-01-01

The machine protection system (MPS) that protects the APS storage ring vacuum chamber from x-ray beams, is active. There are over 650 sensors monitored and networked through the MPS system. About the same number of other process variables are monitored by the much slower EPICS control system, which also has an input to the rf abort chain. The MPS network is still growing with the beam position limits detection system coming on-line. The network configuration, along with a limited description of individual subsystems, is presented

46 CFR 154.1110 - Areas protected by system.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Areas protected by system. 154.1110 Section 154.1110... Firefighting § 154.1110 Areas protected by system. Each water spray system must protect: (a) All cargo tank... valves essential to cargo flow; (f) Each boundary facing the cargo area of each superstructure that...

Modern thyratron crowbar protection systems

International Nuclear Information System (INIS)

Judd, D.A.; Kettle, L.J.; Menown, H.; Newton, B.P.; Nicholls, N.S.; Sheldrake, R.

1992-01-01

Two thyratron crowbar systems for high-power klystrons used in linear accelerators are described. The first, contained in an oil filled tank, is a complete system to protect a klystron powered from a 100-kV, 20-A d.c. supply. In the second system a CX1722 glass thyratron, operating in air, has been retrofitted to a test equipment, in place of a spark gap, to protect an Inductive Output Tube (IOT). An important parameter in the choice of the crowbar thyratron is the total coulombs to be switched. Measurements of these follow-on currents are presented. (R.P.) 4 refs.; 10 figs

Standpipe systems for fire protection

CERN Document Server

Isman, Kenneth E

2017-01-01

This important new manual goes beyond the published NFPA standards on installation of standpipe systems to include the rules in the International Building Code, municipal fire codes, the National Fire Code of Canada, and information on inspection, testing, and maintenance of standpipe systems. Also covered are the interactions between standpipe and sprinkler systems, since these important fire protection systems are so frequently installed together. Illustrated with design examples and practical applications to reinforce the learning experience, this is the go-to reference for engineers, architects, design technicians, building inspectors, fire inspectors, and anyone that inspects, tests or maintains fire protection systems. Fire marshals and plan review authorities that have the responsibility for reviewing and accepting plans and hydraulic calculations for standpipe systems are also an important audience, as are firefighters who actually use standpipe systems. As a member of the committees responsible for s...

Aging assessment for active fire protection systems

International Nuclear Information System (INIS)

Ross, S.B.; Nowlen, S.P.; Tanaka, T.

1995-06-01

This study assessed the impact of aging on the performance and reliability of active fire protection systems including both fixed fire suppression and fixed fire detection systems. The experience base shows that most nuclear power plants have an aggressive maintenance and testing program and are finding degraded fire protection system components before a failure occurs. Also, from the data reviewed it is clear that the risk impact of fire protection system aging is low. However, it is assumed that a more aggressive maintenance and testing program involving preventive diagnostics may reduce the risk impact even further

Figures of Merit Guiding Research on Organic Solar Cells

KAUST Repository

Kirchartz, Thomas; Kaienburg, Pascal; Baran, Derya

2018-01-01

these criteria considering thermodynamic limits, their correlation to photocurrent and photovoltage, and effects on the fill factor. Each criterion is quantified by a figure of merit (FOM) that directly relates to device performance. To ensure a wide

A New Protection System for Islanding Detection in LV Distribution Systems

Directory of Open Access Journals (Sweden)

Anna Rita Di Fazio

2015-04-01

Full Text Available The growth of penetration of Distributed Generators (DGs is increasing the risk of unwanted islanded operation in Low Voltage (LV distribution systems. In this scenario, the existing anti-islanding protection systems, installed at the DG premises and based on classical voltage and frequency relays, are no longer effective, especially in the cases of islands characterized by a close match between generation and load. In this paper, a new protection system for islanding detection in LV distribution systems is proposed. The classical voltage and frequency relays in the DG interface protections are enriched with an innovative Smart Islanding Detector, which adopts a new passive islanding detection method. The aim is to keep the advantages of the classical relays while overcoming the problem of their limited sensitivity in detecting balanced islands. In the paper, to define the requirements of the anti-islanding protection system, the events causing the islanded operation of the LV distribution systems are firstly identified and classified. Then, referring to proposed protection system, its architecture and operation are described and, eventually, its performance is analyzed and validated by experimental laboratory tests, carried out with a hardware-in-the-loop technique.

A protection system for picosecond accelerator

International Nuclear Information System (INIS)

Cao Hongping; Chinese Academy of Sciences, Beijing; Chen Huanguang; Xu Ruinian; Tang Junlong; Li Deming

2006-01-01

A personnel and machine protection system for the picosecond accelerator has been built. The key of the system is to send on/off of three triggering signals which are those of electron gun, 2856 MHz and 476 MHz, respectively, to ensure the safety of users and the accelerator. This paper describes the emergencies interlocked by ADAM5511 and timing trigger processor, and some secondary functions which improve the efficiency of the protection system completed in upper layer software. (authors)

Merits and Limits of Ecosystem Protection for Conserving Wild Salmon in a Northern Coastal British Columbia River

Directory of Open Access Journals (Sweden)

Aaron C. Hill

2010-06-01

Full Text Available Loss and degradation of freshwater habitat reduces the ability of wild salmon populations to endure other anthropogenic stressors such as climate change, harvest, and interactions with artificially propagated fishes. Preservation of pristine salmon rivers has thus been advocated as a cost-effective way of sustaining wild Pacific salmon populations. We examine the value of freshwater habitat protection in conserving salmon and fostering resilience in the Kitlope watershed in northern coastal British Columbia - a large (3186 km2 and undeveloped temperate rainforest ecosystem with legislated protected status. In comparison with other pristine Pacific Rim salmon rivers we studied, the Kitlope is characterized by abundant and complex habitats for salmon that should contribute to high resilience. However, biological productivity in this system is constrained by naturally cold, light limited, ultra-oligotrophic growing conditions; and the mean (± SD density of river-rearing salmonids is currently low (0.32 ± 0.27 fish per square meter; n = 36 compared to our other four study rivers (grand mean = 2.55 ± 2.98 fish per square meter; n = 224. Existing data and traditional ecological knowledge suggest that current returns of adult salmon to the Kitlope, particularly sockeye, are declining or depressed relative to historic levels. This poor stock status - presumably owing to unfavorable conditions in the marine environment and ongoing harvest in coastal mixed-stock fisheries - reduces the salmon-mediated transfer of marine-derived nutrients and energy to the system's nutrient-poor aquatic and terrestrial food webs. In fact, Kitlope Lake sediments and riparian tree leaves had marine nitrogen signatures (δ15N among the lowest recorded in a salmon ecosystem. The protection of the Kitlope watershed is undoubtedly a conservation success story. However, "salmon strongholds" of pristine watersheds may not adequately sustain salmon populations and foster

75 FR 3542 - Rehabilitation Research and Development Service Scientific Merit Review Board; Notice of Meeting

Science.gov (United States)

2010-01-21

... DEPARTMENT OF VETERANS AFFAIRS Rehabilitation Research and Development Service Scientific Merit... (Federal Advisory Committee Act) that the Rehabilitation Research and Development Service Scientific Merit... Board is to review rehabilitation research and development applications for scientific and technical...

76 FR 42167 - Rehabilitation Research and Development Service Scientific Merit Review Board; Notice of Meeting

Science.gov (United States)

2011-07-18

... subcommittees of the Board will meet to evaluate merit review applications: August 9--Rehabilitation Engineering... Rehabilitation. August 16--Rehabilitation Engineering and Prosthetics/Orthotics. August 16-17--Psychological... DEPARTMENT OF VETERANS AFFAIRS Rehabilitation Research and Development Service Scientific Merit...

Advanced worker protection system

Energy Technology Data Exchange (ETDEWEB)

Caldwell, B.; Duncan, P.; Myers, J. [Oceaneering Space Systems, Houston, TX (United States)

1995-10-01

The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D&D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D&D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D&D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project describes the development of an Advanced Worker Protection System (AWPS) which will include a life-support backpack with liquid air for cooling and as a supply of breathing gas, protective clothing, respirators, communications, and support equipment.

Advanced worker protection system

International Nuclear Information System (INIS)

Caldwell, B.; Duncan, P.; Myers, J.

1995-01-01

The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D ampersand D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D ampersand D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D ampersand D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project describes the development of an Advanced Worker Protection System (AWPS) which will include a life-support backpack with liquid air for cooling and as a supply of breathing gas, protective clothing, respirators, communications, and support equipment

Nuclear power plant safety. The merits of separation

International Nuclear Information System (INIS)

Helander, L.I.; Tiren, L.I.

1977-01-01

The paper illustrates how the physical separation of safety-related structures, systems and components can improve the protection of a nuclear power plant against multiple failures that may be caused by events such as fire, pipe-whip, missiles, flooding, hurricanes, lightning etc. Criteria for redundancy and separation requirements affect nuclear plant design in many areas such as building layout, arrangements for fire protection and ventilation, separation of mechanical systems and components, in particular emergency cooling systems, separation of electric equipment and cables. The implementation of the ensuing design criteria for a BWR power plant is described. This design involves the separation of emergency cooling systems into four 50% capacity systems, which are independent and separated, including the distribution network for electric power from on-site standby diesel generators and the circuitry for the reactor protection system. The plant is subdivided into a number of fire zones, each with its own independent ventilation system. The fire zones are further subdivided into a multitude of fire cells such that redundant subsystems are housed in separate cells. These design precautions with regard to fire are complemented by extensive fire fighting systems. (author)

The Philosophy of the New Radiation Protection System

Energy Technology Data Exchange (ETDEWEB)

Wikman, P.

2004-07-01

The International Commission on Radiological Protection has proposed a new philosophy of radiation protection. An important component in the proposed system of protection is the principle ''If the individual is sufficiently protected from a source, then society is also protected from that source''. This principle is here analysed and found to be subject to several problems. The principle reflects the controversial ethical position that the likely harm to several people can be ignored as long as the individual risk is small. The ICRP states that the new system involves a change from a previous utilitarian ethics to an individual-oriented philosophy. It is argued that a rights-based or a duty-based ethic requires a more risk avert interpretation of when an individual is sufficiently protected than what the proposal suggests. It is concluded that the proposed principle contradicts the other important principle in the new system - the optimisation principle. Due to these problems it is suggested that the ICRP ought to discard the proposed principle from the new system of radiation protection. (Author) 7 refs.

The Philosophy of the New Radiation Protection System

International Nuclear Information System (INIS)

Wikman, P.

2004-01-01

The International Commission on Radiological Protection has proposed a new philosophy of radiation protection. An important component in the proposed system of protection is the principle I f the individual is sufficiently protected from a source, then society is also protected from that source . This principle is here analysed and found to be subject to several problems. The principle reflects the controversial ethical position that the likely harm to several people can be ignored as long as the individual risk is small. The ICRP states that the new system involves a change from a previous utilitarian ethics to an individual-oriented philosophy. It is argued that a rights-based or a duty-based ethic requires a more risk avert interpretation of when an individual is sufficiently protected than what the proposal suggests. It is concluded that the proposed principle contradicts the other important principle in the new system - the optimisation principle. Due to these problems it is suggested that the ICRP ought to discard the proposed principle from the new system of radiation protection. (Author) 7 refs

A Review of NASA Human Research Program's Scientific Merit Processes: Letter Report

Science.gov (United States)

Pawelczyk, James A. (Editor); Strawbridge, Larisa M. (Editor); Schultz, Andrea M. (Editor); Liverman, Catharyn T. (Editor)

2012-01-01

At the request of the National Aeronautics and Space Administration (NASA), the Institute of Medicine (IOM) convened the Committee on the Review of NASA Human Research Program's (HRP's) Scientific Merit Assessment Processes in December 2011. The committee was asked to evaluate the scientific merit assessment processes that are applied to directed research tasks2 funded through the HRP and to determine best practices from similar assessment processes that are used in other federal agencies. This letter report and its recommendations are the product of a 10-member ad hoc committee, which included individuals who had previously conducted research under the HRP, were familiar with the HRP s research portfolio and operations, had specific knowledge of peer review processes, or were familiar with scientific merit assessment processes used in other organizations and federal agencies, such as the Canadian Institutes of Health Research (CIHR); National Institutes of Health (NIH); National Science Foundation (NSF); and U.S. Departments of Agriculture (USDA), Defense (DOD), and Transportation.

Televison assessment and identification system for the plutonium protection system

International Nuclear Information System (INIS)

Greenwoll, D.A.

1979-02-01

This report covers the selection, description, and use of the components comprising the Television Assessment and Identification System in the Hanford Plutonium Protection System. This work was sponsored by the Department of Energy/Office of Safeguards and Security (DOE/OSS) as part of the overall Sandia Fixed Facility Physical Protection Program

Figures of merit for microwave photonic phase shifters based on semiconductor optical amplifiers.

Science.gov (United States)

Sancho, Juan; Lloret, Juan; Gasulla, Ivana; Sales, Salvador; Capmany, José

2012-05-07

We theoretically and experimentally compare the performance of two fully tunable phase shifter structures based on semiconductor optical amplifiers (SOA) by means of several figures of merit common to microwave photonic systems. A single SOA stage followed by a tailored notch filter is compared with a cascaded implementation comprising three SOA-based phase shifter stages. Attention is focused on the assessment of the RF net gain, noise figure and nonlinear distortion. Recommendations on the performance optimization of this sort of approaches are detailed.

Teacher Merit Pay: Is It a Good Idea?

Science.gov (United States)

Clabaugh, Gary K.

2009-01-01

President Obama's education agenda, which unhappily seems to be George W. Bush's program squared, contains two major features that will impact teacher pay and working conditions. The first is that charter schools are to be promoted aggressively. The second is an insistence on teacher merit pay. In this article, the author talks about teacher merit…

77 FR 21622 - Rehabilitation Research and Development Service Scientific Merit Review Board; Notice of Meeting

Science.gov (United States)

2012-04-10

... DEPARTMENT OF VETERANS AFFAIRS Rehabilitation Research and Development Service Scientific Merit...-463 (Federal Advisory Committee Act) that a meeting of the Rehabilitation Research and Development Service Scientific Merit Review Board will be held on April 20, 2012, 131 M Street NE., Washington, DC...

75 FR 72872 - Rehabilitation Research and Development Service Scientific Merit Review Board; Notice of Meeting

Science.gov (United States)

2010-11-26

... DEPARTMENT OF VETERANS AFFAIRS Rehabilitation Research and Development Service Scientific Merit...-463 (Federal Advisory Committee Act) that a meeting of the Rehabilitation Research and Development Service Scientific Merit Review Board will be held on December 13-14, 2010, at the Hilton Alexandria Old...

Establishing an Information Security System related to Physical Protection

International Nuclear Information System (INIS)

Jang, Sung Soon; Yoo, Ho Sik

2009-01-01

A physical protection system (PPS) integrates people, procedures and equipment for the protection of assets or facilities against theft, sabotage or other malevolent attacks. In the physical protection field, it is important the maintain confidentiality of PPS related information, such as the alarm system layout, detailed maps of buildings, and guard schedules. In this abstract, we suggest establishing a methodology for an information security system. The first step in this methodology is to determine the information to protect and possible adversaries. Next, system designers should draw all possible paths to the information and arrange appropriate protection elements. Finally he/she should analyze and upgrade their information security system

Half-metallic perovskite superlattices with colossal thermoelectric figure of merit

KAUST Repository

Upadhyay Kahaly, M.; Ozdogan, K.; Schwingenschlö gl, Udo

2013-01-01

Nowadays heavy experimental efforts are focussed on doped oxide thermoelectrics to increase the thermopower and thermoelectric performance. We propose a high thermoelectric figure of merit for half-metallic SrTi1−xCoxO3 (x = 0, 0.125, 0.25, 0.375, and 0.5) in a superlattice with SrTiO3, which is stable at high temperatures and in an oxygen environment. The maximal value of Z hardly depends on the doping, while the temperature at which the maximum occurs increases with the Co concentration. The easy tunability from being an insulator to a half-metal under substitutional doping combined with the colossal figure of merit opens up great potential in the emerging field of spin-caloritronics.

Half-metallic perovskite superlattices with colossal thermoelectric figure of merit

KAUST Repository

Upadhyay Kahaly, M.

2013-05-09

Nowadays heavy experimental efforts are focussed on doped oxide thermoelectrics to increase the thermopower and thermoelectric performance. We propose a high thermoelectric figure of merit for half-metallic SrTi1−xCoxO3 (x = 0, 0.125, 0.25, 0.375, and 0.5) in a superlattice with SrTiO3, which is stable at high temperatures and in an oxygen environment. The maximal value of Z hardly depends on the doping, while the temperature at which the maximum occurs increases with the Co concentration. The easy tunability from being an insulator to a half-metal under substitutional doping combined with the colossal figure of merit opens up great potential in the emerging field of spin-caloritronics.

Nuclear power plant safety, the merits of separation

International Nuclear Information System (INIS)

Helander, L.I.; Tiren, L.I.

1977-01-01

The United States AEC General Design Criteria for Nuclear Power Plants are used worldwide as a basis for the assessment of nuclear plant safety. Several of these criteria require redundancy of safety systems, separation of protection and control systems, consideration of natural phenomena, etc. All these criteria point in one particular direction: the necessity for physically separating the various safety-related systems of a nuclear power plant, particularly with regard to single occurrences that may yield a multiple failure. Requirements in this regard have been amplified by the United States NRC Regulatory Guides and by IEEE Standards. The single occurrence that yields a multiple failure may be, for example, fire, pipe whip, missiles, flooding, hurricanes, or lightning. The paper discusses protection, against the quoted events and others, obtained through applying criteria regarding redundancy and separation of safety-related structures, systems and components. Such criteria affect nuclear plant design in many areas, such as building lay-out, arrangements for fire protection and ventilation, separation of mechanical systems and components, in particular emergency cooling systems, and separation of electric equipment and cables. Implementation of the ensuing design criteria for a BWR power plant is described. This design involves the separation of Emergency Cooling Systems into four 50% Capacity Systems which are independent and separated, including the distribution network for electric power from on-site standby diesel generators and the circuitry for the reactor protection system. The plant is subdivided into a number of fire zones each with its own independent ventilation system. The fire zones are further subdivided into a multitude of fire cells such that redundant subsystems are housed in separate cells. These design precautions with regard to fire are complemented by extensive fire fighting systems

Machine Protection System response in 2011

CERN Document Server

Zerlauth, M; Wenninger, J

2012-01-01

The performance of the machine protection system during the 2011 run is summarized in this paper. Following an analysis of the beam dump causes in comparison to the previous 2010 run, special emphasis will be given to analyse events which risked to exposed parts of the machine to damage. Further improvements and mitigations of potential holes in the protection systems as well as in the change management will be evaluated along with their impact on the 2012 run. The role of the restricted Machine Protection Panel ( rMPP ) during the various operational phases such as commissioning, the intensity ramp up and Machine Developments is being discussed.

Control rod blow out protection system

International Nuclear Information System (INIS)

Dietrich, J.R.; Flinn, W.S.; Groves, M.D.

1979-01-01

An absorber element blow-out protection system for a nuclear reactor having a pressure vessel through which a coolant is circulated. The blow-out protection system includes devices which hydraulically couple groups of guide tubes in which the absorber elements move, the coupling devices limiting coolant lift flow rate to a level commensurate with the raising of individual absorber elements but insufficient to raise a plurality of absorber elements simultaneously

Evaluation of several corrosion protective coating systems on aluminum

Science.gov (United States)

Higgins, R. H.

1981-01-01

A study of several protective coating systems for use on aluminum in seawater/seacoast environments was conducted to review the developments made on protective coatings since early in the Space Shuttle program and to perform comparative studies on these coatings to determine their effectiveness for providing corrosion protection during exposure to seawater/seacoast environments. Panels of 2219-T87 aluminum were coated with 21 different systems and exposed to a 5 percent salt spray for 4000 hr. Application properties, adhesion measurements, heat resistance and corrosion protection were evaluated. For comparative studies, the presently specified Bostik epoxy system used on the SRB structures was included. Results of these tests indicate four systems with outstanding performance and four additional systems with protection almost as good. These systems are based on a chromated pretreatment, a chromate epoxy primer, and a polyurethane topcoat. Consideration for one of these systems should be included for those applications where superior corrosion protection for aluminum surfaces is required.

Incipient fault detection and power system protection for spaceborne systems

Science.gov (United States)

Russell, B. Don; Hackler, Irene M.

1987-01-01

A program was initiated to study the feasibility of using advanced terrestrial power system protection techniques for spacecraft power systems. It was designed to enhance and automate spacecraft power distribution systems in the areas of safety, reliability and maintenance. The proposed power management/distribution system is described as well as security assessment and control, incipient and low current fault detection, and the proposed spaceborne protection system. It is noted that the intelligent remote power controller permits the implementation of digital relaying algorithms with both adaptive and programmable characteristics.

The information protection level assessment system implementation

Science.gov (United States)

Trapeznikov, E. V.

2018-04-01

Currently, the threat of various attacks increases significantly as automated systems become more widespread. On the basis of the conducted analysis the information protection level assessment system establishing objective was identified. The paper presents the information protection level assessment software implementation in the information system by applying the programming language C #. In conclusions the software features are identified and experimental results are represented.

Annexes to the lecture on reactor protection system including engineered features actuation system

International Nuclear Information System (INIS)

Palmaers, W.

1982-01-01

The present paper deals with the fundamentals for a reactor protection system and discusses the following topics: - System lay-out - Analog measured data acquisition - Analog measured data processing - Limit value generation and logical gating - Procesing of the reactor protection actuation signals - Decoupling of the reactor protection system - Mechanical lay-out - Monitoring system and - Emergency control station. (orig./RW)

Operational test report - Project W-320 cathodic protection systems

International Nuclear Information System (INIS)

Bowman, T.J.

1998-01-01

Washington Administrative Code (WAC) 173-303-640 specifies that corrosion protection must be designed into tank systems that treat or store dangerous wastes. Project W-320, Waste Retrieval Sluicing System (WRSS), utilizes underground encased waste transfer piping between tanks 241-C-106 and 241-AY-102. Corrosion protection is afforded to the encasements of the WRSS waste transfer piping through the application of earthen ionic currents onto the surface of the piping encasements. Cathodic protection is used in conjunction with the protective coatings that are applied upon the WRSS encasement piping. WRSS installed two new two rectifier systems (46 and 47) and modified one rectifier system (31). WAC 173-303-640 specifies that the proper operation of cathodic protection systems must be confirmed within six months after initial installation. The WRSS cathodic protection systems were energized to begin continuous operation on 5/5/98. Sixteen days after the initial steady-state start-up of the WRSS rectifier systems, the operational testing was accomplished with procedure OTP-320-006 Rev/Mod A-0. This operational test report documents the OTP-320-006 results and documents the results of configuration testing of integrated piping and rectifier systems associated with the W-320 cathodic protection systems

Validation of reactor core protection system

International Nuclear Information System (INIS)

Lee, Sang-Hoon; Bae, Jong-Sik; Baeg, Seung-Yeob; Cho, Chang-Ho; Kim, Chang-Ho; Kim, Sung-Ho; Kim, Hang-Bae; In, Wang-Kee; Park, Young-Ho

2008-01-01

Reactor COre Protection System (RCOPS), an advanced core protection calculator system, is a digitized one which provides core protection function based on two reactor core operation parameters, Departure from Nucleate Boiling Ratio (DNBR) and Local Power Density (LPD). It generates a reactor trip signal when the core condition exceeds the DNBR or LPD design limit. It consists of four independent channels adapted a two-out-of-four trip logic. System configuration, hardware platform and an improved algorithm of the newly designed core protection calculator system are described in this paper. One channel of RCOPS was implemented as a single channel facility for this R and D project where we performed final integration software testing. To implement custom function blocks, pSET is used. Software test is performed by two methods. The first method is a 'Software Module Test' and the second method is a 'Software Unit Test'. New features include improvement of core thermal margin through a revised on-line DNBR algorithm, resolution of the latching problem of control element assembly signal and addition of the pre-trip alarm generation. The change of the on-line DNBR calculation algorithm is considered to improve the DNBR net margin by 2.5%-3.3%. (author)

Short communication: Genetic lag represents commercial herd genetic merit more accurately than the 4-path selection model.

Science.gov (United States)

Dechow, C D; Rogers, G W

2018-05-01

Expectation of genetic merit in commercial dairy herds is routinely estimated using a 4-path genetic selection model that was derived for a closed population, but commercial herds using artificial insemination sires are not closed. The 4-path model also predicts a higher rate of genetic progress in elite herds that provide artificial insemination sires than in commercial herds that use such sires, which counters other theoretical assumptions and observations of realized genetic responses. The aim of this work is to clarify whether genetic merit in commercial herds is more accurately reflected under the assumptions of the 4-path genetic response formula or by a genetic lag formula. We demonstrate by tracing the transmission of genetic merit from parents to offspring that the rate of genetic progress in commercial dairy farms is expected to be the same as that in the genetic nucleus. The lag in genetic merit between the nucleus and commercial farms is a function of sire and dam generation interval, the rate of genetic progress in elite artificial insemination herds, and genetic merit of sires and dams. To predict how strategies such as the use of young versus daughter-proven sires, culling heifers following genomic testing, or selective use of sexed semen will alter genetic merit in commercial herds, genetic merit expectations for commercial herds should be modeled using genetic lag expectations. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Merit Goods, Education Public Policy--India at Cross Roads

Science.gov (United States)

Misra, Satya Narayan; Ghadai, Sanjaya Ku.

2015-01-01

Merit Goods have always received handsome attention and allocation from countries which have witnessed a congruence between high significant economic growth and Human Development Index (HDI). The Emerging Market Economies (EMEs) have become significant manufacturing hubs by universalizing education and improving their Incremental Capital Output…

Electrical Power Systems Protection and Interdependencies with ICT

OpenAIRE

Milis, George; Kyriakides, Elias; Hadjiantonis, Antonis

2017-01-01

The present chapter discusses the issue of protection of the electrical power systems, addressing all dimensions, from the need of protection to the identified faults and disturbances to the available protection schemes and further considerations, also looking at the challenges brought by recognizing the interdependent nature of the today’s electrical power systems.

Fire protection in ventilation systems and in case of fire operating ventilation systems

International Nuclear Information System (INIS)

Zitzelsberger, J.

1983-01-01

The fire risks in ventilation systems are discussed. It follows a survey of regulations on fire prevention and fire protection in ventilation systems and smoke and heat exhaust systems applicable to nuclear installations in the Federal Republic of Germany. Fire protection concepts for normal systems and for systems operating also in case of fire will be given. Several structural elements for fire protection in those systems will be illustrated with regard to recent research findings

Angle Control-Based Multi-Terminal Out-of-Step Protection System

OpenAIRE

Antans Sauhats; Andrejs Utans; Dmitrijs Antonovs; Andrejs Svalovs

2017-01-01

From time to time a sequence of unexpected and overlapping contingencies may lead to power system angular instability and even blackouts if not addressed adequately by means of an out-of-step (OOS) protection system. The motivation of the paper is an attempt to develop a workable prototype of the OOS protection system. The deficiencies of the protection currently used in the Latvian Power System network are highlighted and a new protection structure is proposed. The protection system comprise...

DLP-systems: Protection from Insiders

Directory of Open Access Journals (Sweden)

Ivan Sergeevich Boridko

2013-02-01

Full Text Available In the paper the necessity of further introduction of modern systems of information protection against internal leaks, including DLP-systems, is justified. The issues of development of training specialists in the field of information security is considered.

14 CFR 25.954 - Fuel system lightning protection.

Science.gov (United States)

2010-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.954 Fuel system lightning protection. The fuel system must be designed and arranged to prevent the ignition of fuel vapor... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel system lightning protection. 25.954...

14 CFR 27.954 - Fuel system lightning protection.

Science.gov (United States)

2010-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Fuel System § 27.954 Fuel system lightning protection. The fuel system must be designed and arranged to prevent the ignition of fuel vapor... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel system lightning protection. 27.954...

14 CFR 29.954 - Fuel system lightning protection.

Science.gov (United States)

2010-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System § 29.954 Fuel system lightning protection. The fuel system must be designed and arranged to prevent the ignition of fuel vapor... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel system lightning protection. 29.954...

14 CFR 23.954 - Fuel system lightning protection.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel system lightning protection. 23.954... Fuel System § 23.954 Fuel system lightning protection. The fuel system must be designed and arranged to prevent the ignition of fuel vapor within the system by— (a) Direct lightning strikes to areas having a...

Advanced nuclear control and protection system ANCAP-80

International Nuclear Information System (INIS)

Asai, Takashi; Okano, Michihiko; Ishibashi, Kengo; Hasegawa, Masakoto; Fukuda, Hiroyoshi; Hosomichi, Renichi.

1983-01-01

Advanced reactor protection systems were developed to improve operational reliability and availability and to ease the burden of operators of Mitsubishi PWR Nuclear Power Stations. (Called ANCAP-80; Advanced Nuclear Control And Protection System) For the PWR plants now being planned and in future plans, Mitsubishi will adopt these systems with the following functional features; (1) Four channel protection logic, (2) Automatic bypass logic, (3) Automatic test provision, (4) Optical isolators. (author)

Search for thermoelectrics with high figure of merit in half-Heusler compounds with multinary substitution

Science.gov (United States)

Choudhary, Mukesh K.; Ravindran, P.

2018-04-01

In order to improve the thermoelectric performance of TiCoSb we have substituted 50% of Ti equally with Zr and Hf at Ti site and Sb with Sn and Se equally at Sb site. The electronic structure of Ti0.5Zr0.25Hf0.25CoSn0.5Se0.5 is investigated using the full potential linearized augmented plane wave method and the thermoelectric transport properties are calculated on the basis of semi-classical Boltzmann transport theory. Our band structure calculations show that Ti0.5Zr0.25Hf0.25CoSn0.5Se0.5 has semiconducting behavior with indirect band gap value of 0.98 eV which follow the empirical rule of 18 valence-electron content to bring semiconductivity in half Heusler compounds, indicating that one can have semiconducting behavior in multinary phase of half Heusler compounds if they full fill the 18 VEC rule and this open-up the possibility of designing thermoelectrics with high figure of merit in half Heusler compounds. We show that at high temperature of around 700K Ti0.5Zr0.25Hf0.25CoSn0.5Se0.5 has high thermoelectric figure of merit of ZT = 1.05 which is higher than that of TiCoSb (˜ 0.95) suggesting that by going from ternary to multinary phase system one can enhance the thermoelectric figure of merit at higher temperatures.

A protection system of low temperature thermo-supply nuclear reactor

International Nuclear Information System (INIS)

Jiang Binsen

1988-09-01

A Protection system of low temperature thermo-supply nuclear reactor is introduced. It is the first protection system, which is designed and manufactred on the basis of Chinese National Standard GB 4083-83 'General Safety Principle of Nuclear Reactor Protection System', to be considered under the circumstances of industry level in China. Advantages of the protection system are as follows: 1)The single failure criteria can fully be fulfilled by the protection system. 2) On-line testing system can be used for detecting all of failure components and quick identifying the failure points in the system. 3) It is convenience for maintenacnce of the system. To complete this project is very important and helpful in promoting the development of the protection system and safety operation of nuclear reactor in China

Reactor protection system including engineered features actuation system

International Nuclear Information System (INIS)

Palmaers, W.

1982-01-01

The safety concept requires to ensure that - the reactor protection system - the active engineered safeguard - and the necessary auxiliary systems are so designed and interfaced in respect of design and mode of action that, in the event of single component failure reliable control of the consequences of accidents remains ensured at all times and that the availability of the power plant is not limited unnecessarily. In order to satisfy these requirements due, importance was attached to a consistent spacial separation of the mutually redundant subsystems of the active safety equipment. The design and layout of the reactor protection system, of the power supply (emergency power supply), and of the auxiliary systems important from the safety engineering point of view, are such that their subsystems also largely satisfy the requirements of independence and spacial separation. (orig./RW)

Programmed system for nuclear power plant protection

International Nuclear Information System (INIS)

Jover, Pierre.

1980-06-01

The progress in the field of microprocessors and large scale integration circuits, have incited to introduce this new technologies into nuclear power plant protection system. The hardware and software design principles are briefly listed; then, a quad-redundant protection system for 1300 MWe PWR, developed in France is described [fr

Universal Curve of Optimum Thermoelectric Figures of Merit for Bulk and Low-Dimensional Semiconductors

Science.gov (United States)

Hung, Nguyen T.; Nugraha, Ahmad R. T.; Saito, Riichiro

2018-02-01

This paper is a contribution to the Physical Review Applied collection in memory of Mildred S. Dresselhaus. Analytical formulas for thermoelectric figures of merit and power factors are derived based on the one-band model. We find that there is a direct relationship between the optimum figures of merit and the optimum power factors of semiconductors despite of the fact that the two quantities are generally given by different values of chemical potentials. By introducing a dimensionless parameter consisting of the optimum power factor and lattice thermal conductivity (without electronic thermal conductivity), it is possible to unify optimum figures of merit of both bulk and low-dimensional semiconductors into a single universal curve that covers many materials with different dimensionalities.

NSTX Protection And Interlock Systems For Coil And Powers Supply Systems

International Nuclear Information System (INIS)

Zhao, X.; Ramakrishnan, S.; Lawson, J.; Neumeyer, C.; Marsala, R.; Schneider, H.

2009-01-01

NSTX at Princeton Plasma Physics Laboratory (PPPL) requires sophisticated plasma positioning control system for stable plasma operation. TF magnetic coils and PF magnetic coils provide electromagnetic fields to position and shape the plasma vertically and horizontally respectively. NSTX utilizes twenty six coil power supplies to establish and initiate electromagnetic fields through the coil system for plasma control. A power protection and interlock system is utilized to detect power system faults and protect the TF coils and PF coils against excessive electromechanical forces, overheating, and over current. Upon detecting any fault condition the power system is restricted, and it is either prevented from initializing or suppressed to de-energize coil power during pulsing. Power fault status is immediately reported to the computer system. This paper describes the design and operation of NSTX's protection and interlocking system and possible future expansion.

The thermoelectric figure of merit of poor thermal conductors

International Nuclear Information System (INIS)

Dixon, A.J.

1977-01-01

Calculations are given to show that for low thermal conductivity materials the radiation losses at even moderate temperatures preclude the use of the Harman technique for measuring the thermoelectric figure of merit. Measurements on liquid Tl 66 Se 34 , which has suitable thermoelectric properties, confirm this. (author)

System and method for quench protection of a superconductor

Science.gov (United States)

Huang, Xianrui; Sivasubramaniam, Kiruba Haran; Bray, James William; Ryan, David Thomas

2008-03-11

A system and method for protecting a superconductor from a quench condition. A quench protection system is provided to protect the superconductor from damage due to a quench condition. The quench protection system comprises a voltage detector operable to detect voltage across the superconductor. The system also comprises a frequency filter coupled to the voltage detector. The frequency filter is operable to couple voltage signals to a control circuit that are representative of a rise in superconductor voltage caused by a quench condition and to block voltage signals that are not. The system is operable to detect whether a quench condition exists in the superconductor based on the voltage signal received via the frequency filter and to initiate a protective action in response.

Digital signal processing in power system protection and control

CERN Document Server

Rebizant, Waldemar; Wiszniewski, Andrzej

2011-01-01

Digital Signal Processing in Power System Protection and Control bridges the gap between the theory of protection and control and the practical applications of protection equipment. Understanding how protection functions is crucial not only for equipment developers and manufacturers, but also for their users who need to install, set and operate the protection devices in an appropriate manner. After introductory chapters related to protection technology and functions, Digital Signal Processing in Power System Protection and Control presents the digital algorithms for signal filtering, followed

A New Physical Protection System Design and Evaluation Process

Energy Technology Data Exchange (ETDEWEB)

Lim, Heoksoon; Kim, Myungsu; Bae, Yeongkyoung; Na, Janghwan [KHNP-CRI, Daejeon (Korea, Republic of)

2014-10-15

International Atomic Energy Agency(IAEA) had established security-related department and has been strengthening security measures against possible sabotage. IAEA enforces the recommendations for the physical protection of NPPs in the INFCIRC/ 225/Rev.5 to the member states and U.S. NRC also enforces the similar requirements in 10 CFR 73.55. Thus, in order to let Korean NPPs meet the new requirements in INFCIRC/225/Rev.5 or U.S. NRC requirements, Korea nuclear licensee should develop or establish appropriate physical protection system (PPS) design methods for the physical protection of the operating NPPs and new NPPs. KHNP is doing the project of 'Development of APR1400 Physical Protection System Design (2012- 2015, KHNP/KAERI /KEPCO E-C)'. This paper describes overview of a physical protection system (PPS) design and evaluation for an advanced nuclear power plant. It found that a new physical protection system (PPS)design and evaluation. KHNP is doing the project of Physical Protection System design according to U.S. NRC requirements and IAEA requirements in INFCIRC /225 /Rev.5 and will complete by 7.31, 2015 for development of APR1400 Physical Protection System. After completing this project, the results of project are expected to apply new NPPs.

Management information system applied to radiation protection services

International Nuclear Information System (INIS)

Grossi, Pablo Andrade; Souza, Leonardo Soares de; Figueiredo, Geraldo Magela; Figueiredo, Arthur

2013-01-01

An effective management information system based on technology, information and people is necessary to improve the safety on all processes and operations subjected to radiation risks. The complex and multisource information flux from all radiation protection activities on nuclear organizations requires a robust tool/system to highlight the strengths and weaknesses and identify behaviors and trends on the activities requiring radiation protection programs. Those organized and processed data are useful to reach a successful management and to support the human decision-making on nuclear organization. This paper presents recent improvements on a management information system based on the radiation protection directives and regulations from Brazilian regulatory body. This radiation protection control system is applied to any radiation protection services and research institutes subjected to Brazilian nuclear regulation and is a powerful tool for continuous management, not only indicating how the health and safety activities are going, but why they are not going as well as planned showing up the critical points. (author)

Management information system applied to radiation protection services

Energy Technology Data Exchange (ETDEWEB)

Grossi, Pablo Andrade; Souza, Leonardo Soares de; Figueiredo, Geraldo Magela; Figueiredo, Arthur, E-mail: pabloag@cdtn.br, E-mail: lss@cdtn.br, E-mail: gmf@cdtn.br, E-mail: arthurqof@gmail.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2013-07-01

An effective management information system based on technology, information and people is necessary to improve the safety on all processes and operations subjected to radiation risks. The complex and multisource information flux from all radiation protection activities on nuclear organizations requires a robust tool/system to highlight the strengths and weaknesses and identify behaviors and trends on the activities requiring radiation protection programs. Those organized and processed data are useful to reach a successful management and to support the human decision-making on nuclear organization. This paper presents recent improvements on a management information system based on the radiation protection directives and regulations from Brazilian regulatory body. This radiation protection control system is applied to any radiation protection services and research institutes subjected to Brazilian nuclear regulation and is a powerful tool for continuous management, not only indicating how the health and safety activities are going, but why they are not going as well as planned showing up the critical points. (author)

Future Interoperability of Camp Protection Systems (FICAPS)

Science.gov (United States)

Caron, Sylvie; Gündisch, Rainer; Marchand, Alain; Stahl, Karl-Hermann

2013-05-01

The FICAPS Project has been established as a Project of the European Defence Agency based on an initiative of Germany and France. Goal of this Project was to derive Guidelines, which by a proper implementation in future developments improve Camp Protection Systems (CPS) by enabling and improving interoperability between Camp Protection Systems and its Equipments of different Nations involved in multinational missions. These Guidelines shall allow for: • Real-time information exchange between equipments and systems of different suppliers and nations (even via SatCom), • Quick and easy replacement of equipments (even of different Nations) at run-time in the field by means of plug and play capability, thus lowering the operational and logistic costs and making the system highly available, • Enhancement of system capabilities (open and modular systems) by adding new equipment with new capabilities (just plug-in, automatic adjustment of the HMI Human Machine Interface) without costly and time consuming validation and test on system level (validation and test can be done on Equipment level), Four scenarios have been identified to summarize the interoperability requirements from an operational viewpoint. To prove the definitions given in the Guideline Document, a French and a German Demonstration System, based on existing national assets, were realized. Demonstrations, showing the capabilities given by the defined interoperability requirements with respect to the operational scenarios, were performed. Demonstrations included remote control of a CPS by another CPS, remote sensor control (Electro-Optic/InfraRed EO/IR) and remote effector control. This capability can be applied to extend the protection area or to protect distant infrastructural assets Demonstrations have been performed. The required interoperability functionality was shown successfully. Even if the focus of the FICAPS project was on camp protection, the solution found is also appropriate for other

Epistemic merit, autonomy, and testimony

Directory of Open Access Journals (Sweden)

Jesús VEGA ENCABO

2008-01-01

Full Text Available In this paper, it is argued that both the informer and the hearer in a testimonial situation deserve epistemic merit insofar as they contribute to the collaborative achievement of sharing knowledge. The paper introduces a distinction between the ideals of self-sufficiency and epistemic autonomy. The autonomous exercise of our epistemic agency is very often carried out under strong conditions of epistemic dependence. Testimony exhibits a kind of social dependence that does not threaten the autonomy of the subjects that need to consider their own epistemic capacities. When involved in a testimonial situation, both speaker and hearer declare, at least implicitly, the standings they occupy in an epistemic space and are obliged to recognise certain epistemic requirements.

Implementation of FPGA-Based Diverse Protection System

International Nuclear Information System (INIS)

Hwang, Soo Yun; Lee, Yoon Hee; Shon, Se Do; Baek, Seung Min

2015-01-01

Obsolete analog and digital hardware platforms in NPPs are commonly replaced with programmable logic controller (PLC) and distributed control system (DCS). Field programmable gate arrays (FPGAs) are highlighted as an alternative to obsolete hardware platforms. FPGAs are digital integrated circuits (ICs) that contain the configurable (programmable) blocks of logic along with configurable interconnections among these blocks. Designers can configure (program) such devices to perform a tremendous variety of tasks. FPGAs have been evolved from the technology of programmable logic device (PLD). Nowadays, they can contain millions of logic gates by nanotechnology and can be used to implement extremely large and complex functions that previously could be realized only using application specific integrated circuits (ASICs). This paper presents the implementation of an FPGA-based diverse protection system (DPS) which executes the protective functions in NPP when the protective functions of the plant protection system (PPS) fails

Implementation of FPGA-Based Diverse Protection System

Energy Technology Data Exchange (ETDEWEB)

Hwang, Soo Yun; Lee, Yoon Hee; Shon, Se Do; Baek, Seung Min [KEPCO Engineering and Construction Company Inc., Daejeon (Korea, Republic of)

2015-10-15

Obsolete analog and digital hardware platforms in NPPs are commonly replaced with programmable logic controller (PLC) and distributed control system (DCS). Field programmable gate arrays (FPGAs) are highlighted as an alternative to obsolete hardware platforms. FPGAs are digital integrated circuits (ICs) that contain the configurable (programmable) blocks of logic along with configurable interconnections among these blocks. Designers can configure (program) such devices to perform a tremendous variety of tasks. FPGAs have been evolved from the technology of programmable logic device (PLD). Nowadays, they can contain millions of logic gates by nanotechnology and can be used to implement extremely large and complex functions that previously could be realized only using application specific integrated circuits (ASICs). This paper presents the implementation of an FPGA-based diverse protection system (DPS) which executes the protective functions in NPP when the protective functions of the plant protection system (PPS) fails.

Power system EMP protection. Final report

International Nuclear Information System (INIS)

Marable, J.H.; Barnes, P.R.; Nelson, D.B.

1975-05-01

Voltage transients induced in electric power lines and control circuits by the electromagnetic pulse (EMP) from high-altitude nuclear detonations may cause widespread power failure and damage in electric power systems. This report contains a parametric study of EMP power line surges and discusses protective measures to minimize their effects. Since EMP surges have considerably greater rates of rise than lightning surges, recommended standards and test procedures are given to assure that surge arresters protect equipment from damage by EMP. Expected disturbances and damage to power systems are reviewed, and actions are presented which distribution companies can take to counter them. These include backup communications methods, stockpiling of vulnerable parts, repair procedures, and dispatcher actions to prevent blackout from EMP-caused instabilities. A long-range program is presented for improving distributors' protection against EMP. This involves employee training, hardware protection for power and control circuits, and improvement of plans for emergency action. (U.S.)

A Cause-Consequence Chart of a Redundant Protection System

DEFF Research Database (Denmark)

Nielsen, Dan Sandvik; Platz, O.; Runge, B.

1975-01-01

A cause-consequence chart is applied in analysing failures of a redundant protection system (a core spray system in a nuclear power plant). It is shown how the diagram provides a basis for calculating two probability measures for malfunctioning of the protection system. The test policy of compone...... of components is taken into account. The possibility of using parameter variation as a basis for the choice of test policy is indicated.......A cause-consequence chart is applied in analysing failures of a redundant protection system (a core spray system in a nuclear power plant). It is shown how the diagram provides a basis for calculating two probability measures for malfunctioning of the protection system. The test policy...

Public Entrepreneurs and the Adoption of Broad-Based Merit Aid beyond the Southeastern United States

Science.gov (United States)

Ingle, William Kyle; Petroff, Ruth Ann

2013-01-01

The concentration of broad-based merit aid adoption in the southeastern United States has been well noted in the literature. However, there are states that have adopted broad-based merit aid programs outside of the Southeast. Guided by multiple theoretical frameworks, including innovation diffusion theory (e.g., Gray, 1973, 1994; Rogers, 2003),…

Angle Control-Based Multi-Terminal Out-of-Step Protection System

Directory of Open Access Journals (Sweden)

Antans Sauhats

2017-03-01

Full Text Available From time to time a sequence of unexpected and overlapping contingencies may lead to power system angular instability and even blackouts if not addressed adequately by means of an out-of-step (OOS protection system. The motivation of the paper is an attempt to develop a workable prototype of the OOS protection system. The deficiencies of the protection currently used in the Latvian Power System network are highlighted and a new protection structure is proposed. The protection system comprises of several strategically located terminals, exchanging information in real time by means of a communication network. The OOS condition detection method is based on system-wide generation sources, electromotive forces, vectors, and angle control. The network splitting decision is based on generator coherence evaluation. Protection terminals determine online the groups of coherent generators and choose the splitting boundary from a predefined transmission lines (TLs cut sets list. The protection system structure, algorithm of operation, and possible IEC 61850 communication standard-based implementation are described.

Integrated crop protection as a system approach

OpenAIRE

Haan, de, J.J.; Wijnands, F.G.; Sukkel, W.

2005-01-01

New farming systems in vegetable production are required as demands for high quality products that do not pollute the environment are rising, and production risks are large and incomes low. The methodology of prototyping new systems is described, especially the themes, parameters and target values connected to integrated crop protection. The role of integrated crop protection in prototyping new systems is discussed. The results of twenty years working with this prototyping methodology are pre...

The Protective Arm of the Renin Angiotensin System (RAS)

DEFF Research Database (Denmark)

understanding of the protective side of the Renin Angiotensin System (RAS) involving angiotensin AT2 receptor, ACE2, and Ang(1-7)/Mas receptor Combines the knowledge of editors who pioneered research on the protective renin angiotensin system including; Dr. Thomas Unger, one of the founders of AT2 receptor......The Protective Arm of the Renin Angiotensin System: Functional Aspects and Therapeutic Implications is the first comprehensive publication to signal the protective role of a distinct part of the renin-angiotensin system (RAS), providing readers with early insight into a complex system which...... will become of major medical importance in the near future. Focusing on recent research, The Protective Arm of the Renin Angiotensin System presents a host of new experimental studies on specific components of the RAS, namely angiotensin AT2 receptors (AT2R), the angiotensin (1-7) peptide with its receptor...

Advanced combustion, emission control, health impacts, and fuels merit review and peer evaluation

Energy Technology Data Exchange (ETDEWEB)

None, None

2006-10-01

This report is a summary and analysis of comments from the Advisory Panel at the FY 2006 DOE National Laboratory Advanced Combustion, Emission Control, Health Impacts, and Fuels Merit Review and Peer Evaluation, held May 15-18, 2006 at Argonne National Laboratory. The work evaluated in this document supports the FreedomCAR and Vehicle Technologies Program. The results of this merit review and peer evaluation are major inputs used by DOE in making its funding decisions for the upcoming fiscal year.

Exact Solution of a Constraint Optimization Problem for the Thermoelectric Figure of Merit

Directory of Open Access Journals (Sweden)

Wolfgang Seifert

2012-03-01

Full Text Available In the classical theory of thermoelectricity, the performance integrals for a fully self-compatible material depend on the dimensionless figure of merit zT. Usually these integrals are evaluated for constraints z = const. and zT = const., respectively. In this paper we discuss the question from a mathematical point of view whether there is an optimal temperature characteristics of the figure of merit. We solve this isoperimetric variational problem for the best envelope of a family of curves z(TT.

Exact Solution of a Constraint Optimization Problem for the Thermoelectric Figure of Merit.

Science.gov (United States)

Seifert, Wolfgang; Pluschke, Volker

2012-03-21

In the classical theory of thermoelectricity, the performance integrals for a fully self-compatible material depend on the dimensionless figure of merit zT. Usually these integrals are evaluated for constraints z = const. and zT = const., respectively. In this paper we discuss the question from a mathematical point of view whether there is an optimal temperature characteristics of the figure of merit. We solve this isoperimetric variational problem for the best envelope of a family of curves z(T)T.

75 FR 972 - Nomination of Existing Marine Protected Areas to the National System of Marine Protected Areas

Science.gov (United States)

2010-01-07

... Marine Protected Areas to the National System of Marine Protected Areas AGENCY: NOAA, Department of... Federal, State and territorial marine protected area programs to join the National System of Marine Protected Areas. SUMMARY: NOAA and the Department of the Interior (DOI) invited Federal, State, commonwealth...

Discussion on radiation protection system from ethical issues

International Nuclear Information System (INIS)

Li, Xutong; Guo, Qiuju

2002-01-01

This paper discussed the relationship between radiation protection system and ethical principle, viz. equity and efficiency. According to the authors' opinions, the main problem that the system of radiation protection facing now is the dose-limitation principle cannot incarnate the equity principle completely. Even though the distinguishing between practice and intervention is no other than solving the problem, but the scheme is not perfect still. Ethical issues should be given more attention and be more researched when we try to modify the radiation protection system today

Novel Directional Protection Scheme for the FREEDM Smart Grid System

Science.gov (United States)

Sharma, Nitish

This research primarily deals with the design and validation of the protection system for a large scale meshed distribution system. The large scale system simulation (LSSS) is a system level PSCAD model which is used to validate component models for different time-scale platforms, to provide a virtual testing platform for the Future Renewable Electric Energy Delivery and Management (FREEDM) system. It is also used to validate the cases of power system protection, renewable energy integration and storage, and load profiles. The protection of the FREEDM system against any abnormal condition is one of the important tasks. The addition of distributed generation and power electronic based solid state transformer adds to the complexity of the protection. The FREEDM loop system has a fault current limiter and in addition, the Solid State Transformer (SST) limits the fault current at 2.0 per unit. Former students at ASU have developed the protection scheme using fiber-optic cable. However, during the NSF-FREEDM site visit, the National Science Foundation (NSF) team regarded the system incompatible for the long distances. Hence, a new protection scheme with a wireless scheme is presented in this thesis. The use of wireless communication is extended to protect the large scale meshed distributed generation from any fault. The trip signal generated by the pilot protection system is used to trigger the FID (fault isolation device) which is an electronic circuit breaker operation (switched off/opening the FIDs). The trip signal must be received and accepted by the SST, and it must block the SST operation immediately. A comprehensive protection system for the large scale meshed distribution system has been developed in PSCAD with the ability to quickly detect the faults. The validation of the protection system is performed by building a hardware model using commercial relays at the ASU power laboratory.

78 FR 50144 - Health Services Research and Development Service, Scientific Merit Review Board; Notice of Meeting

Science.gov (United States)

2013-08-16

... DEPARTMENT OF VETERANS AFFAIRS Health Services Research and Development Service, Scientific Merit... management, and nursing research. Applications are reviewed for scientific and technical merit, mission... Advisory Committee Act, 5 U.S.C. App. 2, that the Health Services Research and Development Service (HSR&D...

77 FR 42365 - Health Services Research and Development Service Scientific Merit Review Board, Notice of Meeting

Science.gov (United States)

2012-07-18

... DEPARTMENT OF VETERANS AFFAIRS Health Services Research and Development Service Scientific Merit...-463 (Federal Advisory Committee Act) that various subcommittees of the Health Services Research and Development Service Scientific Merit Review Board will meet on August 28-30, 2012, at the Boston Omni Parker...

Power system protection 1 principles and components

CERN Document Server

Association, Electricity Training

1995-01-01

The worldwide growth in demand for electricity has forced the pace of developments in electrical power system design to meet consumer needs for reliable, secure and cheap supplies. Power system protection, as a technology essential to high quality supply, is widely recognised as a specialism of growing and often critical importance, in which power system needs and technological progress have combined to result in rapid developments in policy and practice in recent years. In the United Kingdom, the need for appropriate training in power system protection was recognised in the early 1960s with t

Treatment planning figures of merit in thermal and epithermal boron capture therapy of brain tumours

Energy Technology Data Exchange (ETDEWEB)

Wallace, S.A.; Mathur, J.N. (Wollongong Univ., NSW (Australia)); Allen, B.J. (Ansto PMB 1 Menai, NSW (Australia). Biomedicine and Health)

1994-05-01

The boron neutron capture therapy (BNCT) figures of merit of advantage depth, therapeutic depth, modified advantage depth and maximum therapeutic depth have been studied as functions of [sup 10]B tumour to blood ratios and absolute levels. These relationships were examined using the Monte Carlo neutron photon transport code, MCNP, with an ideal 18.4 cm diameter neutron beam incident laterally upon an ellipsoidal neutron photon brain-equivalent model. Mono-energetic beams of 0.025 eV (thermal) and 35 eV (epithermal) were simulated. Increasing the tumour to blood [sup 10]B ratio predictably increases all figures of merit. [sup 10]B concentration was also shown to have a strong bearing on the figures of merit when low levels were present in the system. This is the result of a non-[sup 10]B dependent background dose. At higher levels however, the concentration of [sup 10]B has a diminishing influence. For boron sulphydryl (BSH), little advantage is gained by extending the blood [sup 10]B level beyond 30 ppm, whilst for D, L,-p-boronophenylalanine (BPA) this limit is 10 ppm. Applying the epithermal beam under identical conditions, the therapeutic depth reaches the brain mid-line with a tumour to blood [sup 10]B ratio of only 5.7 for BPA. For BSH, the maximum therapeutic depth reaches the brain mid-line with a tumour to blood ratio of only 1.9 with 30 ppm in the blood. Human data for these compounds are very close to these requirements. (author).

78 FR 44475 - Protection System Maintenance Reliability Standard

Science.gov (United States)

2013-07-24

... that the performance or product has some reliability-related value, then the requirement will have...] Protection System Maintenance Reliability Standard AGENCY: Federal Energy Regulatory Commission, Energy... Commission proposes to approve a revised Reliability Standard, PRC-005- 2--Protection System Maintenance, to...

Automatic coordination of protection devices in distribution system

International Nuclear Information System (INIS)

Comassetto, L.; Bernardon, D.P.; Canha, L.N.; Abaide, A.R.

2008-01-01

Among the several components of distribution systems, protection devices present a fundamental importance, since they aim at keeping the physical integrity not only of the system equipment, but also of the electricians' team and the population in general. The existing tools today in the market that carry out the making of protection studies basically draw curves, and need direct user's interference for the protection devices adjustment and coordination analyses of selectivity, being susceptible to the user's mistakes and not always considering the best technical and economical application. In Brazil, the correct application of the protection devices demand a high amount of time, being extremely laborious due to the great number of devices (around 200 devices), besides the very dynamic behaviour of distribution networks and the need for constant system expansion. This article presents a computational tool developed with the objective of automatically determining the adjustments of all protection devices in the distribution networks to obtain the best technical application, optimizing its performance and making easier protection studies. (author)

Regulatory System of Radiation Protection in Taiwan

International Nuclear Information System (INIS)

Tang, F. T.; Huang, C. C.

2004-01-01

After the radioactive contaminated buildings incident occurred in Taiwan in 1993, the competent authority for radiation protection the Atomic Energy Council (AEC) started to review the structured problem of radiation protection regulatory system. Through several years' investigation and study, the AEC has improved two important tools in radiation protection regulatory system, i.e., control regulations and actual practice, and made them more rigorous and efficient. This paper will make a brief introduction of the efforts that Taiwan has made in this respect. Taiwan's radiation protection control was based on the Atomic Energy Law promulgated in 1968, but the control idea and authorization scope were not sufficient to appropriately respond to the highly developed economy and democracy in Taiwan. After several years' legislative process, the Ionizing Radiation Protection Law (IRP Law) was promulgated and entered into force on February 1, 2003. This IRP Law specifically emphasizes categorized risk management of radiation sources, establishment of personnel licenses and training system, enhancement of public safety control, and implementation of quality assurance program for medical exposure. The Legislative Yuan (Congress) fully authorized the competent authority to establish various technological control regulations according to control necessity without prior review by the Legislative Yuan in advance. As to the penalties of the violations of the IRP Law, the AEC adopts high-rated administrative fines and applies the Criminal Law to those who seriously contaminate the environment. In actual practice, the AEC has constructed a Radiation Protection Control Information System compatible with the IRP Law that fully combines the functions of computers and Internet. The information of facility operators who own radiation sources, radiation protection specialists, and operating personnel are entered into this system, starting from the submission of application of the

Risk Aversion and Support for Merit Pay: Theory and Evidence from Minnesota's Q Comp Program. Working Paper #09-05

Science.gov (United States)

Nadler, Carl; Wiswall, Matthew

2009-01-01

Recent research attributes the lack of merit pay in teaching to the resistance of teachers. This paper examines whether the structure of merit pay affects the types of teachers who support it. We develop a model of the relative utility teachers receive from merit pay versus the current fixed schedule of raises. We show that if teachers are risk…

Modern tools to evaluate and optimize fire protection systems

International Nuclear Information System (INIS)

Alvares, N.J.; Hasegawa, H.K.

1980-01-01

Modern techniques, such as fault tree analysis, can be used to obtain engineering descriptions of specific fire protection systems. The analysis allows establishment of an optimum level of fire protection, and evaluates the level of protection provided by various systems. A prime example: the application to fusion energy experiments

Design and evaluation of physical protection systems of nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

An, Jin Soo; Lee, Hyun Chul; Hwang, In Koo; Kwack, Eun Ho; Choi, Yung Myung

2001-06-01

Nuclear material and safety equipment of nuclear facilities are required to be protected against any kind of theft or sabotage. Physical protection is one of the measures to prevent such illegally potential threats for public security. It should cover all the cases of use, storage, and transportation of nuclear material. A physical protection system of a facility consists of exterior intrusion sensors, interior intrusion sensors, an alarm assessment and communication system, entry control systems, access delay equipment, etc. The design of an effective physical protection system requires a comprehensive approach in which the designers define the objective of the system, establish an initial design, and evaluate the proposed design. The evaluation results are used to determine whether or not the initial design should be modified and improved. Some modelling techniques are commonly used to analyse and evaluate the performance of a physical protection system. Korea Atomic Energy Research Institute(KAERI) has developed a prototype of software as a part of a full computer model for effectiveness evaluation for physical protection systems. The input data elements for the prototype, contain the type of adversary, tactics, protection equipment, and the attributes of each protection component. This report contains the functional and structural requirements defined in the development of the evaluation computer model.

Criminal law repercussions on the Civil Protection System

Science.gov (United States)

Altamura, M.; Musso, L.

2009-09-01

The legal systems of our Countries provide the citizenship with a high level of protection. Personal safety and the protection of property are guaranteed by the State through organized structures among which we can include the Civil Protection. The progress of science and technology has greatly improved monitoring tools, currently used by the Civil Protection, which allow, to a certain extent, to predict and prevent risk and natural hazards. The assertion of an individual right, which in some cases has reached a constitutional rank, to benefit from Civil Protection services and the widespread perception throughout the citizenship of the competence of the system to prevent disasters, often causes people to take legal action against Civil Protection authorities should they fail in their duties to protect. However, the attempt of having both recognized an economic compensation for the suffered loss and the punishment of those whom misled, frequently undergoes criminal law. This process could have results that may jeopardize the effectiveness of Civil Protection service without meeting citizens’ demands. A dual effort is thus necessary in order to solve such a problem. On the one hand, an interdisciplinary knowledge needs to pervade criminal law in an attempt to relieve its self-referentiality and pretended supremacy. On the other hand an alternative, and more agile, system -such as civil or administrative law- has to be identified in order to respond to the legitimate requests for protection in the case of a faulty behaviour of the authorities.

Distributed systems for protecting nuclear power stations

International Nuclear Information System (INIS)

Jover, P.

1980-05-01

The advantages of distributed control systems for the control of nuclear power stations are obviously of great interest. Some years ago, EPRI, (Electric Power Research Institute) showed that multiplexing the signals is technically feasible, that it enables the availability specifications to be met and costs to be reduced. Since then, many distributed control systems have been proposed by the manufacturers. This note offers some comments on the application of the distribution concept to protection systems -what should be distributed- and ends with a brief description of a protection system based on microprocessors for the pressurized power stations now being built in France [fr

Distributed systems for the protection of nuclear stations

International Nuclear Information System (INIS)

Jover, P.

1980-01-01

The advantages of distributed control systems usually mentioned are improved exploitation, cost reduction, and adaptation to changes in technology. These advantages are obviously very interesting for nuclear power plant applications, and many such systems have been proposed. This note comments on the application of the distributed system concept to protection systems - what should be distributed - and closes with a brief description of a protection system based on microprocessors for pressurized water stations being built in France. (auth) [fr

Evolution of the system of radiological protection

International Nuclear Information System (INIS)

2005-11-01

One of the main challenges facing radiological protection experts is how to integrate radiological protection within modern concepts of and approaches to risk governance. It is within this context that the International Commission on Radiological Protection (ICRP) decided to develop new general recommendations to replace its Publication 60 recommendations of 1990. In the process of developing these new recommendations, the views of the ICRP have evolved significantly, largely due to stakeholder involvement that has been actively solicited by the ICRP. In this regard, it was upheld during the First Asian Regional Conference organised by the NEA in October 2002 that the implementation of the new system must allow for regional, societal and cultural differences. In order to ensure appropriate consideration of these differences, the NEA organised the Second Asian Regional Conference on the Evolution of the System of Radiological Protection. Held in Tokyo on 28-29 July 2004, the conference included presentations by the ICRP Chair as well as by radiological experts from Australia, China, Japan and Korea. Within their specific cultural and socio-political milieu, Asia-Pacific and western ways of thought on how to improve the current system of radiological protection were presented and discussed. These ways of thinking, along with a summary of the conference results, are described in these proceedings. (author)

First MARS exercise of merit recognition: what's the outcome?

CERN Multimedia

Staff Association

2007-01-01

In June, the decisions concerning the various forms of merit recognition of the staff are taken. The Staff Association commends all those involved and, in particular, the supervisors who, for this first exercise, have had to assess your performance in record time, in accordance with the new provisions in the recently revised administrative circular no. 26.

Decentralized Adaptive Overcurrent Protection for Medium Voltage Maritime Power Systems

DEFF Research Database (Denmark)

Ciontea, Catalin-Iosif; Bak, Claus Leth; Blaabjerg, Frede

2016-01-01

the entire electrical network and changes the relay settings accordingly, but this approach is not adequate for the maritime power systems. This paper propose a decentralized adaptive protection method, where each protection relay is able to identify by itself the network status without the need of a central...... control unit. The new adaptive protection method is based on communication between the overcurrent relays and the equipment that could affect the protection system, such as circuit breakers and generators. Using PSCAD, the proposed method is implemented in a test medium voltage maritime power system......More and more maritime applications as marine vessels and offshore platforms need an adaptive protection power system. However, the adaptive protection is yet to be implemented in the maritime sector. Usually, the adaptive protection implies the existence of a central control unit that monitors...

Displacements of Metallic Thermal Protection System Panels During Reentry

Science.gov (United States)

Daryabeigi, Kamran; Blosser, Max L.; Wurster, Kathryn E.

2006-01-01

Bowing of metallic thermal protection systems for reentry of a previously proposed single-stage-to-orbit reusable launch vehicle was studied. The outer layer of current metallic thermal protection system concepts typically consists of a honeycomb panel made of a high temperature nickel alloy. During portions of reentry when the thermal protection system is exposed to rapidly varying heating rates, a significant temperature gradient develops across the honeycomb panel thickness, resulting in bowing of the honeycomb panel. The deformations of the honeycomb panel increase the roughness of the outer mold line of the vehicle, which could possibly result in premature boundary layer transition, resulting in significantly higher downstream heating rates. The aerothermal loads and parameters for three locations on the centerline of the windward side of this vehicle were calculated using an engineering code. The transient temperature distributions through a metallic thermal protection system were obtained using 1-D finite volume thermal analysis, and the resulting displacements of the thermal protection system were calculated. The maximum deflection of the thermal protection system throughout the reentry trajectory was 6.4 mm. The maximum ratio of deflection to boundary layer thickness was 0.032. Based on previously developed distributed roughness correlations, it was concluded that these defections will not result in tripping the hypersonic boundary layer.

Localization of equipment for digital plant protection system

Energy Technology Data Exchange (ETDEWEB)

Koo, I. S.; Park, H. Y.; Lee, C. K. and others

2000-10-01

The objective of this project lies on the development of design requirements, establishment of structure and manufacture procedures, development of the software verification and validation(V and V) techniques of the digital plant protection system. The functional requirements based on the analog protection system and digital design requirements are introduced, the processor and system bus for safety grade equipment are selected and the interface requirements and the design specification have been developed in order to manufacture the quick prototype of the digital plant protection system. The selection guidelines of parts, software development and coding and testing for digital plant protection system have been performed through manufacturing the quick prototype based on the developed design specification. For the software verification and validation, the software review plan and techniques of verification and validation have been researched. The digital validation system is developed in order to verify the quick prototype. The digital design requirements are reviewed by the software safety plan and V and V plans. The formal methods for verifying the safety-grade software are researched, then the methodology of formal analysis and testing have been developed.

Localization of equipment for digital plant protection system

International Nuclear Information System (INIS)

Koo, I. S.; Park, H. Y.; Lee, C. K. and others

2000-10-01

The objective of this project lies on the development of design requirements, establishment of structure and manufacture procedures, development of the software verification and validation(V and V) techniques of the digital plant protection system. The functional requirements based on the analog protection system and digital design requirements are introduced, the processor and system bus for safety grade equipment are selected and the interface requirements and the design specification have been developed in order to manufacture the quick prototype of the digital plant protection system. The selection guidelines of parts, software development and coding and testing for digital plant protection system have been performed through manufacturing the quick prototype based on the developed design specification. For the software verification and validation, the software review plan and techniques of verification and validation have been researched. The digital validation system is developed in order to verify the quick prototype. The digital design requirements are reviewed by the software safety plan and V and V plans. The formal methods for verifying the safety-grade software are researched, then the methodology of formal analysis and testing have been developed

Outer skin protection of columbium Thermal Protection System (TPS) panels

Science.gov (United States)

Culp, J. D.

1973-01-01

A coated columbium alloy material system 0.04 centimeter thick was developed which provides for increased reliability to the load bearing character of the system in the event of physical damage to and loss of the exterior protective coating. The increased reliability to the load bearing columbium alloy (FS-85) was achieved by interposing an oxidation resistant columbium alloy (B-1) between the FS-85 alloy and a fused slurry silicide coating. The B-1 alloy was applied as a cladding to the FS-85 and the composite was fused slurry silicide coated. Results of material evaluation testing included cyclic oxidation testing of specimens with intentional coating defects, tensile testing of several material combinations exposed to reentry profile conditions, and emittance testing after cycling of up to 100 simulated reentries. The clad material, which was shown to provide greater reliability than unclad materials, holds significant promise for use in the thermal protection system of hypersonic reentry vehicles.

2012 DOE Vehicle Technologies Program Annual Merit Review

Energy Technology Data Exchange (ETDEWEB)

None

2012-10-26

The 2012 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting was held May 14-18, 2012 in Crystal City, Virginia. The review encompassed all of the work done by the Hydrogen Program and the Vehicle Technologies Program: a total of 309 individual activities were reviewed for Vehicle Technologies, by a total of 189 reviewers. A total of 1,473 individual review responses were received for the technical reviews.

44 CFR 65.14 - Remapping of areas for which local flood protection systems no longer provide base flood protection.

Science.gov (United States)

2010-10-01

... local flood protection systems no longer provide base flood protection. 65.14 Section 65.14 Emergency... § 65.14 Remapping of areas for which local flood protection systems no longer provide base flood... process of restoring a flood protection system that was: (i) Constructed using Federal funds; (ii...

Protective relaying of power systems using mathematical morphology

CERN Document Server

Wu, QH; Ji, TY

2009-01-01

Discusses the development of novel protective relaying algorithms, using Mathematical Morphology (MM). This book introduces the fundamental principles of MM, and brings together the applications of MM to develop different protective relaying algorithms for the protection of a variety of power system components.

New measuring and protection system at VR-1 training reactor

International Nuclear Information System (INIS)

Kropik, M.; Jurickova, M.

2006-01-01

The contribution describes the new measuring and protection system of the VR-1 training reactor. The measuring and protection system upgrade is an integral part of the reactor I and C upgrade. The new measuring and protection system of the VR-1 reactor consists of the operational power measuring and the independent power protection systems. Both systems measure the reactor power and power rate, initiate safety action if safety limits are exceeded and send data (power, power rate, status, etc.) to the reactor control system. The operational power measuring system is a full power range system that receives signal from a fission chamber. The signal is evaluated according to the reactor power either in the pulse or current mode. The current mode utilizes the DC current and Campbell techniques. The new independent power protection system operates in the two highest reactor power decades. It receives signals from a boron chamber and evaluates it in the pulse mode. Both systems are computer based. The operational power measuring and independent power protection systems are diverse - different types and location of chambers, completely different hardware, software algorithms for the power and power rate calculations, software development tools and teems for the software manufacturing. (author)

75 FR 77569 - Special Conditions: Gulfstream Model GVI Airplane; Electronic Flight Control System Mode...

Science.gov (United States)

2010-12-13

... Some failures of this system may lead to a degraded operating mode that does not merit a classic ``failure warning'' but in which flight envelope protection is lost and the flight crew must fly the... surfaces for both normal and failure states, and it generates the actual surface commands that provide for...

Report on task I: fire protection system study

International Nuclear Information System (INIS)

Bernard, E.A.; Cano, G.L.

1977-02-01

This study (1) evaluates, on a comparative basis, the national and international regulatory and insurance standards that serve as guidance for fire protection within the nuclear power industry; (2) analyzes the recommendations contained in the major reports on the Browns Ferry Fire; (3) proposes quantitative safety goals and evaluation methods for Nuclear Power Plant Fire Protection Systems (NPPFPS); (4) identifies potential improvements that may be incorporated into NPPFPS; and (5) recommends a plan of action for continuation of the fire protections systems study

Illustration of distributed generation effects on protection system coordination

Science.gov (United States)

Alawami, Hussain Adnan

Environmental concerns, market forces, and emergence of new technologies have recently resulted in restructuring electric utility from vertically integrated networks to competitive deregulated entities. Distributed generation (DG) is playing a major role in such deregulated markets. When they are installed in small amounts and small sizes, their impacts on the system may be negligible. When their penetration levels increase as well as their sizes, however, they may start affecting the system performance from more than one aspect. Power system protection needs to be re-assessed after the emergence of DG. This thesis attempts to illustrate the impact of DG on the power system protection coordination. It will study the operation of the impedance relays, fuses, reclosers and overcurrent relays when a DG is added to the distribution network. Different DG sizes, distances from the network and locations within the distribution system will be considered. Power system protection coordination is very sensitive to the DG size where it is not for the DG distance. DG location has direct impact on the operation of the protective devices especially when it is inserted in the middle point of the distribution system. Key Words, Distributed Generation, Impedance relay, fuses, reclosers, overcurrent relays, power system protection coordination.

An integrated numerical protection system (SPIN)

International Nuclear Information System (INIS)

Savornin, J.L.; Bouchet, J.M.; Furet, J.L.; Jover, P.; Sala, A.

1978-01-01

Developments in technology have now made it possible to perform more sophisticated protection functions which follow more closely the physical phenomena to be monitored. For this reason the Commissariat a l'energie atomique, Merlin-Gerin, Cerci and Framatome have embarked on the joint development of an Integrated Numerical Protection System (SPIN) which will fulfil this objective and will improve the safety and availability of power stations. The system described involves the use of programmed numerical techniques and a structure based on multiprocessors. The architecture has a redundancy of four. Throughout the development of the project the validity of the studies was confirmed by experiments. A first numerical model of a protection function was tested in the laboratory and is now in operation in a power station. A set of models was then introduced for checking the main components of the equipment finally chosen prior to building and testing a prototype. (author)

SNAP: a tool for nuclear physical protection system modeling

International Nuclear Information System (INIS)

Engi, D.; Grant, F.H. III.

1979-10-01

Nuclear safeguards systems are concerned, in part, with the physical protection of nuclear materials. The function of a physical protection system is to define the facility against adversary activities which could lead to theft of nuclear material or sabotage resulting in a radiological release. The Safeguards Network Analysis Procedure (SNAP) provides a convenient and standard analysis methodology for the evaluation of physical protection system analysis. This paper describes a detailed application of SNAP to a hypothetical nuclear facility

Development of In-Core Protection System

International Nuclear Information System (INIS)

Cho, J. H; Kim, C. H.; Kim, J. H.; Jeong, S. H.; Sohn, S. D.; BaeK, S. M.; YOON, J. H.

2016-01-01

In-core Protection System (ICOPS) is an on-line digital computer system which continuously calculates Departure from Nucleate Boiling Ratio (DNBR) and Local Power Density (LPD) based on plant parameters to make trip decisions based on the computations. The function of the system is the same as that of Core Protection Calculator System (CPCS) and Reactor Core Protection System (RCOPS) which are applied to Optimized Power Reactor 1000 (OPR1000) and Advanced Power Reactor 1400 (APR1400). The ICOPS has been developed to overcome the algorithm related obstacles in overseas project. To achieve this goal, several algorithms were newly developed and hardware and software design was updated. The functional design requirements document was developed by KEPCO-NF and the component design was conducted by Doosan. System design and software implementation were performed by KEPCO-E and C, and software Verification and Validation (V and V) was performed by KEPCO-E and C and Sure Softtech. The ICOPS has been developed to overcome the algorithm related obstacles in overseas project. The function of I/O simulator was improved even though the hardware platform is the same as that of RCOPS for Shin-Hanul 1 and 2. SCADE was applied to the implementation of ICOPS software, and the V and V system for ICOPS which satisfies international standards was developed. Although several further detailed design works remain, the function of ICOPS has been confirmed. The ICOPS will be applied to APR+ project, and the further works will be performed in following project

Development of In-Core Protection System

Energy Technology Data Exchange (ETDEWEB)

Cho, J. H; Kim, C. H.; Kim, J. H.; Jeong, S. H.; Sohn, S. D.; BaeK, S. M.; YOON, J. H. [KEPCO Engineering and Construction Co., Deajeon (Korea, Republic of)

2016-10-15

In-core Protection System (ICOPS) is an on-line digital computer system which continuously calculates Departure from Nucleate Boiling Ratio (DNBR) and Local Power Density (LPD) based on plant parameters to make trip decisions based on the computations. The function of the system is the same as that of Core Protection Calculator System (CPCS) and Reactor Core Protection System (RCOPS) which are applied to Optimized Power Reactor 1000 (OPR1000) and Advanced Power Reactor 1400 (APR1400). The ICOPS has been developed to overcome the algorithm related obstacles in overseas project. To achieve this goal, several algorithms were newly developed and hardware and software design was updated. The functional design requirements document was developed by KEPCO-NF and the component design was conducted by Doosan. System design and software implementation were performed by KEPCO-E and C, and software Verification and Validation (V and V) was performed by KEPCO-E and C and Sure Softtech. The ICOPS has been developed to overcome the algorithm related obstacles in overseas project. The function of I/O simulator was improved even though the hardware platform is the same as that of RCOPS for Shin-Hanul 1 and 2. SCADE was applied to the implementation of ICOPS software, and the V and V system for ICOPS which satisfies international standards was developed. Although several further detailed design works remain, the function of ICOPS has been confirmed. The ICOPS will be applied to APR+ project, and the further works will be performed in following project.

'H-Bahn' - Dortmund demonstration system. Automatic vehicle protection system

Energy Technology Data Exchange (ETDEWEB)

Rosenkranz

1984-01-01

The automatic vehicle protection system of the H-Bahn at the Universtiy of Dortmund is responsible for fail-safe operating of the automatic vehicles. Its functions are protection of vehicle operation and protection of passengers boarding and leaving the vehicles. These functions are managed decentrally by two fail-safe operating controllers. Besides the well-known relay-techniques of railway-fail-safe systems, electronics are applied which are based on safe operating URTL-microcontrollers. These are controlled by software stored in EPROMs. A connection link using glass-fibres serves for safe data-exchange between the two fail-safe operating controllers. The experts' favourable reports on 'train protection and safety during passenger processing' were completed in March 84; thus, transportation of passengers could start in April 84.

Systems and methods for photovoltaic string protection

Science.gov (United States)

Krein, Philip T.; Kim, Katherine A.; Pilawa-Podgurski, Robert C. N.

2017-10-25

A system and method includes a circuit for protecting a photovoltaic string. A bypass switch connects in parallel to the photovoltaic string and a hot spot protection switch connects in series with the photovoltaic string. A first control signal controls opening and closing of the bypass switch and a second control signal controls opening and closing of the hot spot protection switch. Upon detection of a hot spot condition the first control signal closes the bypass switch and after the bypass switch is closed the second control signal opens the hot spot protection switch.

Architecture and Fault Identification of Wide-area Protection System

Directory of Open Access Journals (Sweden)

Yuxue Wang

2012-09-01

Full Text Available Wide-area protection system (WAPS is widely studied for the purpose of improvng the performance of conventional backup protection. In this paper, the system architecture of WAPS is proposed and its key technologies are discussed in view of engineering projects. So a mixed structurecentralized-distributed structure which is more suitable for WAPS in limited power grid region, is obtained based on the advantages of the centralized structure and distributed structure. Furthermore, regional distance protection algorithm was taken as an example to illustrate the functions of the constituent units. Faulted components can be detected based on multi-source imformation fuse in the algorithm. And the algorithm cannot only improve the selectivity, the rapidity, and the reliability of relaying protection but also has high fault tolerant capability. A simulation of 220 kV grid systems in Easter Hubei province shows the effectiveness of the wide-area protection system presented by this paper.

A critical review of the system of radiation protection

International Nuclear Information System (INIS)

2000-01-01

Our modern, information society is increasingly interested in transparency and participation in many aspects of government, and this is particularly true in areas involving public health and environmental protection. Radiation protection is no exception to this trend. Scientific rationale that was once sufficient to explain radiation protection theory and practice is no longer adequate. The need to address and communicate theory, practice and the decision-making process to a wider audience has given rise to numerous debates and led the radiation protection community to revisit the framework of the system of radiation protection. The very fundamentals of the system of radiation protection continue to be questioned in a healthy fashion, and many aspects have been identified which could better serve stakeholders given some additional thought in the light of modern societal needs. This report is the summary of the NEA's first reflections in this area, and describes those aspects of the current international system of radiation protection that could be improved. Suggested directions for improvement are provided. (author)

Dependability Evaluation of Advanced Diverse Protection System

International Nuclear Information System (INIS)

Oh, Yang Gyun; Lee, Yoon Hee; Sohn, Se Do; Baek, Seung Min; Lee, Sang Jeong

2014-01-01

For the mitigation of anticipated transients without scram (ATWS) as well as common cause failure (CCF) within the plant protection system (PPS) and the emergency safety feature . component control system (ESF-CCS), the diverse protection system (DPS) has been designed by KEPCO Engineering and Construction Company. Recently KEPCO E and C has developed the advanced diverse protection system (ADPS), which has four redundant channels, in an attempt to enhance a fault-tolerant capability of the system. For the evaluation of overall system improvement effects of the ADPS compared with the DPS, the dependability evaluation results are described herein. For all dependability attributes, this paper suggests a practical dependability evaluation method which uses quantitative dependability scores and indices. An overall dependability evaluation index (DEI) for the ADPS is evaluated with the average value of reliability/ security/maintainability/safety indices (i.e., RID, SID, MID, and SID') for dependability. The evaluation results show that the DEI value of ADPS can be improved by approximately 23% compared with that of the DPS, thanks to its fault-tolerant system architecture, software design changes, and external interface design features. Several suggestions have been made, in this paper, of an overall quantitative dependability evaluation method for the nuclear instrumentation and control (I and C) systems including the DPS and ADPS, and the usefulness of dependability evaluation on nuclear I and C systems has been confirmed

Reflections on receiving the ASIS&T 2016 Award of Merit

DEFF Research Database (Denmark)

Ingwersen, Peter

2016-01-01

At the ASIS&T Annual Meeting in Copenhagen, Peter Ingwersen expressed surprise and gratitude for being honored with the Association’s 2016 Award of Merit. The professor emeritus from Denmark’s Royal School of Library and Information Science thanked peers for recognizing him as a mentor and research...

The protection of photovoltaic power systems from lightning

Science.gov (United States)

Rogers, C. B.

Lightning protection techniques at nine prototype photovoltaic power system sites with outputs from 18-225 kW are described. Noting that protection schemes are devised to fit isokeraunic data for specific sites, grounding is cited as a common feature for all systems. The grounds are, in separate instances, connected to junction boxes, frames of the solar cell panels, lead from the dc center, from the dc negative terminal, from the frames and equipment, at the array turntable, or from the building rebar frames. The dc power cables are protected by either metal conduit, metal conduit ground wire, direct burial, by rigid metal conduit, ground conductors, or by ground conductors at the ends of the conduit run. Costs run from 0.01-0.28$/W, with all the systems outfitted with bypass and blocking diodes. Direct stroke protection is viewed as less important than isokeraunic data.

78 FR 30870 - Nomination of Existing Marine Protected Areas to the National System of Marine Protected Areas

Science.gov (United States)

2013-05-23

... Marine Protected Areas to the National System of Marine Protected Areas AGENCY: National Marine Protected...) invited federal, state, commonwealth, and territorial marine protected area (MPA) programs with... of Marine Protected Areas of the United States (Framework), developed in response to Executive Order...

The Role of Merit-Based Scholarships in Meeting Affordability Goals

Science.gov (United States)

Pugh, Susan L.; Thompson, Roger J.

2010-01-01

Institutions across the country continue to ponder and evaluate strategies for aligning financial aid to complement their enrollment goals. Two Indiana University enrollment managers examine the purposeful application of institutional aid in financial aid packaging. In response to the debate about the of merit-based aid vs. the appropriate share…

System architecture for microprocessor based protection system

International Nuclear Information System (INIS)

Gallagher, J.M. Jr.; Lilly, G.M.

1976-01-01

This paper discusses the architectural design features to be employed by Westinghouse in the application of distributed digital processing techniques to the protection system. While the title of the paper makes specific reference to microprocessors, this is only one (and the newest) of the building blocks which constitutes a distributed digital processing system. The actual system structure (as realized through utilization of the various building blocks) is established through considerations of reliability, licensability, and cost. It is the intent of the paper to address these considerations licenstions as they relate to the architectural design features. (orig.) [de

Passive fire building protection system evaluation (case study: millennium ict centre)

Science.gov (United States)

Rahman, Vinky; Stephanie

2018-03-01

Passive fire protection system is a system that refers to the building design, both regarding of architecture and structure. This system usually consists of structural protection that protects the structure of the building and prevents the spread of fire and facilitate the evacuation process in case of fire. Millennium ICT Center is the largest electronic shopping center in Medan, Indonesia. As a public building that accommodates the crowd, this building needs a fire protection system by the standards. Therefore, the purpose of this study is to evaluate passive fire protection system of Millennium ICT Center building. The study was conducted to describe the facts of the building as well as direct observation to the research location. The collected data is then processed using the AHP (Analytical Hierarchy Process) method in its weighting process to obtain the reliability value of passive fire protection fire system. The results showed that there are some components of passive fire protection system in the building, but some are still unqualified. The first section in your paper

Enhancement of observability and protection of smart power system

Science.gov (United States)

Siddique, Abdul Hasib

It is important for a modern power grid to be smarter in order to provide reliable and sustainable supply of electricity. Traditional way of receiving data from the wired system is a very old and outdated technology. For a quicker and better response from the electric system, it is important to look at wireless systems as a feasible option. In order to enhance the observability and protection it is important to integrate wireless technology with the modern power system. In this thesis, wireless network based architecture for wide area monitoring and an alternate method for performing current measurement for protection of generators and motors, has been adopted. There are basically two part of this project. First part deals with the wide area monitoring of the power system and the second part focuses more on application of wireless technology from the protection point of view. A number of wireless method have been adopted in both the part, these includes Zigbee, analog transmission (Both AM and FM) and digital transmission. The main aim of our project was to propose a cost effective wide area monitoring and protection method which will enhance the observability and stability of power grid. A new concept of wireless integration in the power protection system has been implemented in this thesis work.

Free parameter, figure of merit and ionization quench in liquid scintillation counting

International Nuclear Information System (INIS)

Carles, P. Grau; Malonda, A. Grau

2001-01-01

A statistical study of the detection process demonstrates that the free parameter is essential to compute the counting efficiency in both CIEMAT/NIST and TDCR methods. An analysis of the computed counting efficiencies shows the uselessness of old definition of the figure of merit. A new definition is required and we adopt the idea of taking quantities related with the output of the photomultiplier. In addition, we justify the application of the chemical quenching simulation with the electronic variation of the photomultiplier gain. Finally, we describe a new procedure to determine the figure of merit and the optimum ionization-quenching factor from the pulse spectrum of different radionuclides. The robustness of the new procedure is tested with three different sets of stopping power for low-energy electrons

Merits of the fat-tailed Barbarine sheep raised in different production systems in Tunisia: digestive, productive and reproductive characteristics.

Science.gov (United States)

Ben Salem, Hichem; Lassoued, Narjess; Rekik, Mourad

2011-10-01

Barbarine sheep is the dominant breed in Tunisia. This fat-tailed breed present in all production systems is characterised by metabolic and digestive adaptation to the contrasting environment conditions prevailing in the country (heat stress, water deprivation, salinity etc.). The fat tail (1.5 to 7 kg) is an energy reservoir that is used in periods of feed scarcity. Moreover, the rumen of this breed harbours a microflora enabling it to valorize low-quality roughages and native range vegetation. Barbarine sheep could make benefit from a wide range of local feed resources like fodder shrubs (e.g. cactus and oldman saltbushes), tannin-containing shrubs (e.g. Acacia cyanophylla) and agro-industrial by-products (e.g. olive cake, bran etc. conserved in the form of feed blocks or pellets). It has a very shallow anoestrous, the intensity of which is dependant upon nutrition conditions rather than day length as temperate breeds. Productive and reproductive performances of late pregnant-early suckling, pre-mating ewes and also rams of this breed are not affected when some alternative feed resources replace common feedstuffs which are expensive and cannot afford regularly to smallholders. In brief, the merits of the Barbarine sheep in the production systems and other main adaptive mechanisms of this breed are discussed in this paper. The prospective of Barbarine sheep husbandry in the system dynamics, climate change and the evolution of the socioeconomic context are also envisaged.

Beam loss monitor system for machine protection

CERN Document Server

Dehning, B

2005-01-01

Most beam loss monitoring systems are based on the detection of secondary shower particles which depose their energy in the accelerator equipment and finally also in the monitoring detector. To allow an efficient protection of the equipment, the likely loss locations have to be identified by tracking simulations or by using low intensity beams. If superconducting magnets are used for the beam guiding system, not only a damage protection is required but also quench preventions. The quench levels for high field magnets are several orders of magnitude below the damage levels. To keep the operational efficiency high under such circumstances, the calibration factor between the energy deposition in the coils and the energy deposition in the detectors has to be accurately known. To allow a reliable damage protection and quench prevention, the mean time between failures should be high. If in such failsafe system the number of monitors is numerous, the false dump probability has to be kept low to keep a high operation...

Assessment of physical protection systems: EVA method

International Nuclear Information System (INIS)

Bernard, J.-L.; Lamotte, C.; Jorda, A.

2001-01-01

CEA's missions in various sectors of activity such as nuclear, defence, industrial contracts and the associated regulatory requirements, make it necessary to develop a strategy in the field of physical protection. In particular, firms having nuclear materials are subject to the July 25, 1980 law no.80-572 on the protection and control of nuclear materials. A holding permit delivered by the regulatory authority is conditioned to the protection by the operator of the nuclear materials used. In France it is the nuclear operator who must demonstrate, in the form of a security study, that potential aggressors would be neutralised before they could escape with the material. To meet these requirements, we have developed methods to assess the vulnerability of our facilities. The EVA method, the French acronym for 'Evaluation de la vulnerabilite des Acces' (access vulnerability system) allows dealing with internal and external threats involving brutal actions. In scenarios relating to external threat, the intruders get past the various barriers of our protection system, attempting to steal a large volume of material in one swoop and then escape. In the case of internal threat, the goal is the same. However, as the intruder usually has access to the material in the scope of his activities, the action begins at the level of the target. Our protection system is based on in-depth defense where the intruders are detected and then delayed in their advance towards their target to allow time for intervention forces to intercept them

Fail-safe computer-based plant protection systems

International Nuclear Information System (INIS)

Keats, A.B.

1983-01-01

A fail-safe mode of operation for computers used in nuclear reactor protection systems was first evolved in the UK for application to a sodium cooled fast reactor. The fail-safe properties of both the hardware and the software were achieved by permanently connecting test signals to some of the multiplexed inputs. This results in an unambiguous data pattern, each time the inputs are sequentially scanned by the multiplexer. The ''test inputs'' simulate transient excursions beyond defined safe limits. The alternating response of the trip algorithms to the ''out-of-limits'' test signals and the normal plant measurements is recognised by hardwired pattern recognition logic external to the computer system. For more general application to plant protection systems, a ''Test Signal Generator'' (TSG) is used to compute and generate test signals derived from prevailing operational conditions. The TSG, from its knowledge of the sensitivity of the trip algorithm to each of the input variables, generates a ''test disturbance'' which is superimposed upon each variable in turn, to simulate a transient excursion beyond the safe limits. The ''tripped'' status yielded by the trip algorithm when using data from a ''disturbed'' input forms part of a pattern determined by the order in which the disturbances are applied to the multiplexer inputs. The data pattern formed by the interleaved test disturbances is again recognised by logic external to the protection system's computers. This fail-safe mode of operation of computer-based protection systems provides a powerful defence against common-mode failure. It also reduces the importance of software verification in the licensing procedure. (author)

Heat Exchange in “Human body - Thermal protection - Environment” System

Science.gov (United States)

Khromova, I. V.

2017-11-01

This article is devoted to the issues of simulation and calculation of thermal processes in the system called “Human body - Thermal protection - Environment” under low temperature conditions. It considers internal heat sources and convective heat transfer between calculated elements. Overall this is important for the Heat Transfer Theory. The article introduces complex heat transfer calculation method and local thermophysical parameters calculation method in the system called «Human body - Thermal protection - Environment», considering passive and active thermal protections, thermophysical and geometric properties of calculated elements in a wide range of environmental parameters (water, air). It also includes research on the influence that thermal resistance of modern materials, used in special protective clothes development, has on heat transfer in the system “Human body - Thermal protection - Environment”. Analysis of the obtained results allows adding of the computer research data to experiments and optimizing of individual life-support system elements, which are intended to protect human body from exposure to external factors.

Estimating total economic merit for the Portuguese Holstein cattle population under new economic conditions

Directory of Open Access Journals (Sweden)

Joana B.M. Almeida

2013-12-01

Full Text Available The objective of this study was to develop a total economic merit index that identifies more profitable animals using Portugal as a case study to illustrate the recent economic changes in milk production. Economic values were estimated following future global prices and EU policy, and taking into consideration the priorities of the Portuguese dairy sector. Economic values were derived using an objective system analysis with a positive approach, that involved the comparison of several alternatives, using real technical and economic data from national dairy farms. The estimated relative economic values revealed a high importance of production traits, low for morphological traits and a value of zero for somatic cell score. According to several future market expectations, three scenarios for milk production were defined: a realistic, a pessimistic and an optimistic setting, each with projected future economic values. Responses to selection and efficiency of selection of the indices were compared to a fourth scenario that represents the current selection situation in Portugal, based on individual estimated breeding values for milk yield. Although profit resulting from sale of milk per average lactation in the optimistic scenario was higher than in the realistic scenario, the volatility of future economic conditions and uncertainty about the future milk pricing system should be considered. Due to this market instability, genetic improvement programs require new definitions of profit functions for the near future. Effective genetic progress direction must be verified so that total economic merit formulae can be adjusted and selection criteria redirected to the newly defined target goals.

A Fall Protection System for High-Rise Construction

Directory of Open Access Journals (Sweden)

Haluk Çeçen

2013-01-01

Full Text Available In construction industry, the number of fatal and nonfatal occupational injuries is higher than other industries. Among causes of these accidents, “falls” play a key role. This situation reveals the importance for carrying out research in fall protection systems. In this paper, a practical, economical, and functional fall protection system is introduced. Following determination and evaluation of existing solutions, weekly brainstorming meetings were held among the responsible project staff (general coordinator, project coordinator, project manager, site manager, and health and safety manager. As a result of these meetings, design criteria were developed. Based on these criteria, the fall protection system for high-rise construction (FPSFHC was developed which satisfied all the specified design criteria. Required materials were procured from local dealers. In this paper, criteria used in design and details of the final design are presented. Field performance of the system is evaluated, and recommendations for further development and standardization of the system are added.

Reactor protection systems for the Replacement Research Reactor, ANSTO

International Nuclear Information System (INIS)

Morris, C.R.

2003-01-01

The 20-MW Replacement Research Reactor Project which is currently under construction at ANSTO will have a combination of a state of the art triplicated computer based reactor protection system, and a fully independent, and diverse, triplicated analogue reactor protection system, that has been in use in the nuclear industry, for many decades. The First Reactor Protection System (FRPS) consists of a Triconex triplicated modular redundant system that has recently been approved by the USNRC for use in the USA?s power reactor program. The Second Reactor Protection System is a hardwired analogue system supplied by Foxboro, the Spec 200 system, which is also Class1E qualified. The FRPS is used to drop the control rods when its safety parameter setpoints have been reached. The SRPS is used to drain the reflector tank and since this operation would result in a reactor poison out due to the time it would take to refill the tank the FRPS trip setpoints are more limiting. The FRPS and SRPS have limited hardwired indications on the control panels in the main control room (MCR) and emergency control centre (ECC), however all FRPS and SRPS parameters are capable of being displayed on the reactor control and monitoring system (RCMS) video display units. The RCMS is a Foxboro Series I/A control system which is used for plant control and monitoring and as a protection system for the cold neutron source. This paper will provide technical information on both systems, their trip logics, their interconnections with each other, and their integration into the reactor control and monitoring system and control panels. (author)

Design of the interlock and protection system for the SPIDER experiment

International Nuclear Information System (INIS)

Pomaro, N.; Grando, L.; Luchetta, A.; Paolucci, F.; Sartori, F.

2013-01-01

Highlights: •A custom designed interlock and protection system for SPIDER experiment is described. •It includes two subsystems implementing slow and fast protection functions. •High reliability PLCs are adopted for slow protection. •Fiber-optic based, custom designed fast logic circuitry is proposed for fast protection. •Accelerators breakdown events are also managed by the fast subsystem. -- Abstract: Unprecedented levels of beam energy and power are required for ITER Neutral Beam Heating systems. SPIDER experiment is an experimental device aimed to test and optimize a full size beam source satisfying ITER requirements. SPIDER experiment operation involves high power, voltage, temperature, and gas pressure. All these critical conditions are present simultaneously, so that any failure if not properly detected and managed is likely to cause severe damage. The Interlock and Protection System is a high-reliability system devoted to the investment protection of SPIDER. Its main purpose is to manage abnormal events occurring in one or more plants in order to minimize adverse consequences. The Interlock System also manages the SPIDER Operating Modes, defining the set and status of the Plants used in the various possible experimental configurations. In addition, the Interlock and Protection System takes care of particular events occurring during normal SPIDER operation, i.e. electrical arcs between accelerator grids, named breakdowns. Their treatment is committed to the Interlock and Protection System, as they need to be managed timely and with absolute reliability like actual faults. To perform the required functions, the Interlock and Protection System is interfaced with most SPIDER plants and with the SPIDER Control and Data Acquisition System. The paper describes the rationale of the protection functions, their implementation in the design and the technical specifications of the system

Sub-assembly accident protection instrumentation systems

International Nuclear Information System (INIS)

Vaughan, G.J.; Lunt, A.R.W.; Evans, N.J.; Lawrence, L.A.J.

1982-01-01

The possibility of an incident in a sub-assembly progressing to the stage at which the whole core may be at hazard has to be guarded against. It is proposed that for CDFR specific instrumentation will be provided to protect against this incident. Three such systems are described, these are: Acoustic Boiling Noise Detection, Burst Pin Detection and Individual Sub-Assembly Thermocouple (ISAT) monitoring. In the ISAT case, multiplexers and microprocessors are employed, using novel techniques to ensure failure-to-safety. The role of these systems and the implementation of them in the reactor design are also considered. It is concluded that sufficient protection can be provided for both core and breeder sub-assemblies

On line protection systems for induction motors

International Nuclear Information System (INIS)

Colak, I.; Celik, H.; Sefa, I.; Demirbas, S.

2005-01-01

Protection of induction motors is very important since they are widely used in industry for many applications due to their high robustness, reliability, low cost and maintenance, high efficiency and long service life. So, protecting these motors is crucial for operations. This paper presents a combined protection approach for induction motors. To achieve this, the electrical values of the induction motor were measured with sensitivity ±1% through a data acquisition card and processed with software developed in Visual C++. An on line protection system for induction motors was achieved easily and effectively. The experimental results have shown that the induction motor was protected against the possible problems faced during the operation. The software developed for this protection provides flexible and reliable media for operators and their motors. It is expected that the motor protection achieved in this study might be faster than the classical techniques and also may be applied to larger motors easily after small modifications of the software

[Applications of DNA identification technology in protection of wild animals].

Science.gov (United States)

Ni, Ping-Ya; Pei, Li; Ge, Wen-Dong; Zhang, Ying; Yang, Xue-Ying; Xu, Xiao-Yu; Tu, Zheng

2011-12-01

With the development of biotechnology, forensic DNA identification technology in protection of wild animals has been used more and more widely. This review introduces the global status of wildlife crime and the relevant protection to wildlife, outlines the practical applications of forensic DNA identification technology with regard to species identification, determination of geographic origin, individual identification and paternity identification. It focus on the techniques commonly used in DNA typing and their merits and demerits, as well as the problems and prospects of forensic DNA technology for wildlife conservation.

Operational testing of a figure of merit for overall task performance

Science.gov (United States)

Lemay, Moira

1990-01-01

An overall indicator or figure of merit (FOM), for the quality of pilot performance is needed to define optimal workload levels, predict system failure, measure the impact of new automation in the cockpit, and define the relative contributions of subtasks to overall task performance. A normative FOM was developed based on the calculation of a standard score for each component of a complex task. It reflected some effects, detailed in an earlier study, of the introduction of new data link technology into the cockpit. Since the technique showed promise, further testing was done. A new set of data was obtained using the recently developed Multi-Attribute Task Battery. This is a complex battery consisting of four tasks which can be varied in task demand, and on which performance measures can be obtained. This battery was presented to 12 subjects in a 20 minute trial at each of three levels of workload or task demand, and performance measures collected on all four tasks. The NASA-TLX workload rating scale was presented at minutes 6, 12, and 18, of each trial. A figure of merit was then obtained for each run of the battery by calculating a mean, SD, and standard score for each task. Each task contributed its own proportion to the overall FOM, and relative contributions changed with increasing workload. Thus, the FOM shows the effect of task changes, not only on the individual task that is changed, but also on the performance of other tasks and of the whole task. The cost to other tasks of maintaining constant performance on an individual task can be quantified.

Thermoelectric-figure-of-merit enhancement of silicon-germanium through nanocomposite concept

Science.gov (United States)

Wang, Dezhi

SiGe alloy has been the thermoelectric material element of RTGs (Radioisotope thermoelectric power generators) for more than 20 years because of its good performance at high temperature. It also has a very high potential application in converting exhaust heat into useful electricity, which currently attracts a lot of research interest in the automotive industry where 40% of the energy was rejected as exhaust heat. However, its low conversion efficiency (8%) is a major concern although it is the best in practice. A new concept, namely Si-Ge nanocomposite, was proposed to enhance thermoelectric figure-of-merit. Fast heating pressure sintering was found to be an appropriate synthesizing method and a lab-made direct current-induced hot press system was established. It can reach l200°C within several minutes and many parameters can be controlled. The uniquely designed graphite die assembly can stand l60MPa pressure which is better than the best commercial products (127MPa). Numerous Si-Ge nanocomposite samples were pressed using our DC hot press. Fully dense n-type Si-Ge nanocomposite samples of nanoSi80nanoGe20P were finally obtained. The nanocomposite structure was characterized via XRD, SEM, EDS, and TEM. The proposed nanocomposite structure, dots in a matrix, was observed. Most importantly, the thermoelectric property measurements showed that the Si-Ge nanocomposite of n-type nanoSi80nanoGe20 possessed higher electrical conductivity but lower thermal conductivity, thus a higher ZT than that of n-type nanoSi80microGe20. This result proved that thermoelectric-figure-of-merit enhancement through the nanocomposite concept was the right direction.

Safety Analysis for Power Reactor Protection System

International Nuclear Information System (INIS)

Eisawy, E.A.; Sallam, H.

2012-01-01

The main function of a Reactor Protection System (RPS) is to safely shutdown the reactor and prevents the release of radioactive materials. The purpose of this paper is to present a technique and its application for used in the analysis of safety system of the Nuclear Power Plant (NPP). A more advanced technique has been presented to accurately study such problems as the plant availability assessments and Technical Specifications evaluations that are becoming increasingly important. The paper provides the Markov model for the Reactor Protection System of the NPP and presents results of model evaluations for two testing policies in technical specifications. The quantification of the Markov model provides the probability values that the system will occupy each of the possible states as a function of time.

Problems in creating enviroment and health protection systems

International Nuclear Information System (INIS)

Vorob'ev, E.I.; Reznichenko, V.Yu.

1981-01-01

The problems in creating environmental and health protection systems are considered with relation to development of nuclear energetics facilities. A problem of transition from the system of detection and observation to the uniform system of environment and health protection and control is set. The objectives and problems of such a system are analyzed and the basic principles of their construction are outlined. A system conception for a fuel energetic complex is described. Usefulness of such systems in solving problems of sites of industrial objects including nuclear power industrial objects, of removal of these objects from service and etc. is shown. New requirements to medical-biological investigations on designing of such a system are discussed [ru

Protective systems and its protective switching elements on local failures of large slow-capacitor bank system

International Nuclear Information System (INIS)

Hasegawa, Mitsuo; Inoue, Kunikazu; Ueno, Isao.

1994-01-01

In various applications of pulsed power technologies, large capacitor bank systems are used to feed high current impulse to different experimental devices. The accidental electric breakdown in one of the capacitors in a parallel connection of the large bank may result in serious damages such as mechanical explosion and oil effusion or fire. In most fast banks, each unit capacitor has an output gap switch, which is expected to decouple the capacitors one another. However, no such special element is adopted usually in the slow bank system, partly because of the economical consideration. We have developed a novel and inexpensive protective element for these relatively slow capacitor banks, utilizing a concept of the enclosed type of the fast breakers. The principle of the operation of the protection elements is verified by a simulation experiment. Their practical effectiveness is also successfully demonstrated in the application to the system of the pulsed high magnetic field generator. (author)

Advanced physical protection systems for facilities and transportation

International Nuclear Information System (INIS)

Jones, O.E.

1976-01-01

Sandia Laboratories is developing advanced physical protection safeguards in order to improve the security of special nuclear materials, facilities, and transportation. Computer models are being used to assess the cost-effectiveness of alternative systems for protecting facilities against external attack which may include internal assistance, and against internal theft or sabotage. Physical protection elements such as admittance controls, portals and detectors, perimeter and interior intrusion alarms, fixed and remotely activated barriers, and secure communications are being evaluated, adapted, and where required, developed. New facilities safeguards concepts which involve ''control loops'' between physical protection and materials control elements are being evolved jointly between Sandia Laboratories and Los Alamos Scientific Laboratory. Special vehicles and digital communications equipment have been developed for the ERDA safe-secure transportation system. The current status and direction of these activities are surveyed

Advanced physical protection systems for facilities and transportation

International Nuclear Information System (INIS)

Jones, O.E.

1976-01-01

Sandia Laboratories is developing advanced physical protection safeguards in order to improve the security of special nuclear materials, facilities, and transportation. Computer models are being used to assess the cost-effectiveness of alternative systems for protecting facilities against external attack which may include internal assistance, and against internal theft or sabotage. Physical protection elements such as admittance controls, portals and detectors, perimeter and interior intrusion alarms, fixed and remotely-activated barriers, and secure communications are being evaluated, adapted, and where required, developed. New facilities safeguards concepts which involve (control loops) between physical protection and materials control elements are being evolved jointly between Sandia Laboratories and Los Alamos Scientific Laboratory. Special vehicles and digital communications equipment have been developed for the ERDA safe-secure transportation system. The current status and direction of these activities are surveyed

Railway automatic safety protection system based on GPS

Directory of Open Access Journals (Sweden)

Fu Hai Juan

2016-01-01

Full Text Available The automatic protection system of railway safety is designed for the railway construction workers to protect alarm, and the safety protection device by using GPS satellite positioning system to acquire location information of the operating point, through the CTC/TDCS system and computer monitoring system for the running of the train position and the arithmetic distance. Achieving timely and continuously forecasts about the distance of the train which is apart from the operating point to prompt the voice alarm of the approaching train. Using digital technology to realize the function of the traditional analog interphone, eliminates the quality problems of the call. With the GSM-R, mobile wireless transmission channel and terminal technology, it overcomes the restrictions of the analog interphone which influenced by communication distance and more problems of blind areas. Finally to achieve practical, convenient, applicable and adaptable design goals.

Metabolic safety-margins do not differ between cows of high and low genetic merit for milk production

DEFF Research Database (Denmark)

Knight, Christopher Harold; Alamer, Mohammed A; Sorensen, Annette

2004-01-01

Three galactopoietic stimuli, frequent milking (4X), bovine somatotrophin (bST) and thyroxine (T4) were used in an additive stair-step design to achieve maximum output (metabolic capacity) in six peak-lactation cows of high genetic merit (HT) and six of low genetic merit (LT). A further six of ea...... the commonly held belief that selective breeding of dairy cows for high milk production has rendered them markedly more susceptible to metabolic disturbances.......Three galactopoietic stimuli, frequent milking (4X), bovine somatotrophin (bST) and thyroxine (T4) were used in an additive stair-step design to achieve maximum output (metabolic capacity) in six peak-lactation cows of high genetic merit (HT) and six of low genetic merit (LT). A further six of each...... elevated heart rate and significant loss of body weight and condition compared with the combination of 4X and bST. As a result, treatments were discontinued, on an individual cow basis, before completion of this 6-week phase. Time on experiment did not differ between HT and LT. The results do not support...

Large thermal protection system panel

Science.gov (United States)

Weinberg, David J. (Inventor); Myers, Franklin K. (Inventor); Tran, Tu T. (Inventor)

2003-01-01

A protective panel for a reusable launch vehicle provides enhanced moisture protection, simplified maintenance, and increased temperature resistance. The protective panel includes an outer ceramic matrix composite (CMC) panel, and an insulative bag assembly coupled to the outer CMC panel for isolating the launch vehicle from elevated temperatures and moisture. A standoff attachment system attaches the outer CMC panel and the bag assembly to the primary structure of the launch vehicle. The insulative bag assembly includes a foil bag having a first opening shrink fitted to the outer CMC panel such that the first opening and the outer CMC panel form a water tight seal at temperatures below a desired temperature threshold. Fibrous insulation is contained within the foil bag for protecting the launch vehicle from elevated temperatures. The insulative bag assembly further includes a back panel coupled to a second opening of the foil bag such that the fibrous insulation is encapsulated by the back panel, the foil bag, and the outer CMC panel. The use of a CMC material for the outer panel in conjunction with the insulative bag assembly eliminates the need for waterproofing processes, and ultimately allows for more efficient reentry profiles.

Seismic design criteria of fire protection systems for DOE facilities

International Nuclear Information System (INIS)

Hardy, G.; Cushing, R.; Driesen, G.

1991-01-01

Fire protection systems are critical to the safety of personnel and to the protection of inventory during any kind of emergency situation that involves a fire. The importance of these fire protection systems is hightened for DOE facilities which often house nuclear, chemical or scientific processes. Current research into the topic of open-quotes fires following earthquakesclose quotes has demonstrated that the risks of a fire starting as a result of a major earthquake can be significant. Thus, fire protection systems need to be designed to withstand the anticipated seismic event for the site in question

Fire protection countermeasures for containment ventilation systems

International Nuclear Information System (INIS)

Alvares, N.; Beason, D.; Bergman, V.; Creighton, J.; Ford, H.; Lipska, A.

1980-01-01

The goal of this project is to find countermeasures to protect High Efficiency Particulate Air (HEPA) filters, in exit ventilation ducts, from the heat and smoke generated by fire. Initially, methods were developed to cool fire-heated air by fine water spray upstream of the filters. It was recognized that smoke aerosol exposure to HEPA filters could also cause disruption of the containment system. Through testing and analysis, several methods to partially mitigate the smoke exposure to the HEPA filters were identified. A continuous, movable, high-efficiency prefilter using modified commercial equipment was designed. The technique is capable of protecting HEPA filters over the total time duration of the test fires. The reason for success involved the modification of the prefiltration media. Commercially available filter media has particle sorption efficiency that is inversely proportional to media strength. To achieve properties of both efficiency and strength, rolling filter media were laminated with the desired properties. The approach was Edisonian, but truncation in short order to a combination of prefilters was effective. The application of this technique was qualified, since it is of use only to protect HEPA filters from fire-generated smoke aerosols. It is not believed that this technique is cost effective in the total spectrum of containment systems, especially if standard fire protection systems are available in the space. But in areas of high-fire risk, where the potential fuel load is large and ignition sources are plentiful, the complication of a rolling prefilter in exit ventilation ducts to protect HEPA filters from smoke aerosols is definitely justified

Renovation of the cathodic protection system

NARCIS (Netherlands)

Schuten, G.; Leggedoor, J.; Polder, R.B.; Peelen, W.H.A.

2003-01-01

The first system for Cathodic Protection of concrete in the Netherlands was applied to a one bicycle lane of a bridge suffering corrosion due to de-icing salt penetration in 1986. This CP system was based on the Ferex 100S conducting polymer cable anode in a cementitious overlay. Its functioning was

Impact of Y2K problem on physical protection system

International Nuclear Information System (INIS)

Kumar, R.; Swadia, N.S.; Zanwar, P.S.; Mishra, G.P.; Salunke, A.S.; Nigam, R.K.

1999-01-01

Year 2000 related system failures/problems in Physical Protection System pose no threat to general safety and functioning of any nuclear facility. But there can be potential security threats having radiation safety and non-proliferation concern and hence should be given due importance. Reviewing and testing Physical Protection System for Y2K compliance are easier than other systems as it does not directly affect operation of the plant. The existing emergency response capability at the nuclear facilities should be utilizes effectively to mitigate any Y2K induced events on Physical Protection System with dedicated manpower and channeled efforts

Anode protection system for shutdown of solid oxide fuel cell system

Science.gov (United States)

Li, Bob X; Grieves, Malcolm J; Kelly, Sean M

2014-12-30

An Anode Protection Systems for a SOFC system, having a Reductant Supply and safety subsystem, a SOFC anode protection subsystem, and a Post Combustion and slip stream control subsystem. The Reductant Supply and safety subsystem includes means for generating a reducing gas or vapor to prevent re-oxidation of the Ni in the anode layer during the course of shut down of the SOFC stack. The underlying ammonia or hydrogen based material used to generate a reducing gas or vapor to prevent the re-oxidation of the Ni can be in either a solid or liquid stored inside a portable container. The SOFC anode protection subsystem provides an internal pressure of 0.2 to 10 kPa to prevent air from entering into the SOFC system. The Post Combustion and slip stream control subsystem provides a catalyst converter configured to treat any residual reducing gas in the slip stream gas exiting from SOFC stack.

Analog subsystem for the plutonium protection system

International Nuclear Information System (INIS)

Arlowe, H.D.

1978-12-01

An analog subsystem is described which monitors certain functions in the Plutonium Protection System. Rotary and linear potentiometer output signals are digitized, as are the outputs from thermistors and container ''bulge'' sensors. This work was sponsored by the Department of Energy/Office of Safeguards and Security (DOE/OSS) as part of the overall Sandia Fixed Facility Physical Protection Program

Ability of dairy cows to be inseminated according to breed and genetic merit for production traits under contrasting pasture-based feeding systems.

Science.gov (United States)

Bedere, N; Disenhaus, C; Ducrocq, V; Leurent-Colette, S; Delaby, L

2017-05-01

Strong genetic selection on production traits is considered to be responsible for the declined ability of dairy cows to ensure reproduction. The present study aimed to quantify the effect of genetic characteristics (breeds and genetic merit for production traits) and feeding systems (FS) on the ability of dairy cows to be inseminated. An experiment was conducted during 9 years on Normande and Holstein cows assigned to contrasted pasture-based FS. Diets were based on maize silage in winter and grazing plus concentrate in spring in the High FS; and on grass silage in winter and grazing with no concentrate during spring in the low FS. Within breed, cows were classified into two genetic groups with similar estimated breeding values (EBV) for milk solids: cows with high EBV for milk yield were included in a Milk-Group and those with high EBV for fat and protein contents were included in a Content-Group. Holstein produced more milk throughout lactation than Normande cows (+2294 kg in the High FS and +1280 kg in the Low FS, PGenetic group neither affected ovulation detection rate nor DAI1. Within breed and FS, cows with high genetic merit for milk yield had later CLA and DAI1. Cows in the High FS produced more milk and lost less condition to nadir than cows in the Low FS. FS did not affect dairy cows' ability to be inseminated. However, cows with higher milk protein content, and presumably better energy balance, had earlier CLA (P<0.01) and DAI1 (P<0.10). In addition, higher milk yield was associated with poorer ovulation detection rate and oestrus intensity (P<0.05). The study showed that at similar EBV level for milk solids, selection for increased milk fat and protein content resulted in improved cyclicity and similar oestrous expression and submission rates compared with selection for increased milk yield.

The assessment of science: the relative merits of post-publication review, the impact factor, and the number of citations.

Science.gov (United States)

Eyre-Walker, Adam; Stoletzki, Nina

2013-10-01

The assessment of scientific publications is an integral part of the scientific process. Here we investigate three methods of assessing the merit of a scientific paper: subjective post-publication peer review, the number of citations gained by a paper, and the impact factor of the journal in which the article was published. We investigate these methods using two datasets in which subjective post-publication assessments of scientific publications have been made by experts. We find that there are moderate, but statistically significant, correlations between assessor scores, when two assessors have rated the same paper, and between assessor score and the number of citations a paper accrues. However, we show that assessor score depends strongly on the journal in which the paper is published, and that assessors tend to over-rate papers published in journals with high impact factors. If we control for this bias, we find that the correlation between assessor scores and between assessor score and the number of citations is weak, suggesting that scientists have little ability to judge either the intrinsic merit of a paper or its likely impact. We also show that the number of citations a paper receives is an extremely error-prone measure of scientific merit. Finally, we argue that the impact factor is likely to be a poor measure of merit, since it depends on subjective assessment. We conclude that the three measures of scientific merit considered here are poor; in particular subjective assessments are an error-prone, biased, and expensive method by which to assess merit. We argue that the impact factor may be the most satisfactory of the methods we have considered, since it is a form of pre-publication review. However, we emphasise that it is likely to be a very error-prone measure of merit that is qualitative, not quantitative.

Research on the Effects of Rewards: Implications for Annual Merit Pay.

Science.gov (United States)

Burke, Richard R.

Some research suggests reduced cooperation and collaboration among college faculty may result when annual pay increments are based on merit evaluations. Various theories and principles have been put forward to explain these effects. The overjustification theory suggests that extrinsically presented rewards become more salient than one's intrinsic…

Adoption of digital safety protection system in Japan

International Nuclear Information System (INIS)

Ogiso, Z.

1998-01-01

The application of micro-processor-based digital controllers has been widely propagated among various industries in recent years. While in the nuclear power plant industry, the application of them has also been expanding gradually starting from non-safety related systems, taking advantage of their reliability and maintainability over the conventional analog devices. Based on the careful study of the feasibility of digital controllers to the safety protection system, the Tokyo Electric Power Company proposed on May 1989 the adoption of digital controllers to the safety protection system in the Application for Permission of Establishment of Kashiwazaki-Kariwa units 6 and 7 (ABWR-1350Mwe each). MITI, Ministry of International Trade and Industry, the Japanese regulatory body for electric power generating facilities, had approved this application after careful review. This paper describes a series of supporting activities leading to the MITI's approval of the digital safety protection system and the MITI's licensing activities. (author)

14 CFR 25.1316 - System lightning protection.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false System lightning protection. 25.1316... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Equipment General § 25.1316 System lightning... systems to perform these functions are not adversely affected when the airplane is exposed to lightning...

NSTX-U Digital Coil Protection System Software Detailed Design

Energy Technology Data Exchange (ETDEWEB)

None

2014-06-01

The National Spherical Torus Experiment (NSTX) currently uses a collection of analog signal processing solutions for coil protection. Part of the NSTX Upgrade (NSTX-U) entails replacing these analog systems with a software solution running on a conventional computing platform. The new Digital Coil Protection System (DCPS) will replace the old systems entirely, while also providing an extensible framework that allows adding new functionality as desired.

MERIT - The high intensity liquid mercury target experiment at the CERN PS

CERN Document Server

Efthymiopoulos, I

2009-01-01

The MERIT experiment is a proof-of-principle test of a target system for high power proton beams to be used as front-end for a Neutrino Factory complex or a Muon Collider. The experiment took data in autumn 2007 with the fast extracted beam from the CERN Proton Synchrotron (PS) to a maximum intensity of about 30 × 1012 protons per pulse. The target system, based on a free mercury jet, allowed investigation of the interseption of a 4-MW proton beam inside a 15-T magnetic field required to capture the low-energy secondary pions as the source of the required intense muon beams. Particle detectors have been installed around the target setup to measure the secondary particle flux out of the target and probe cavitation effects in the mercury jet when exited with a beam of variable intensity. With the analysis of the data ongoing, results will be presented here that demonstrate the validity of the liquid target concept.

Fault Identification Algorithm Based on Zone-Division Wide Area Protection System

OpenAIRE

Xiaojun Liu; Youcheng Wang; Hub Hu

2014-01-01

As the power grid becomes more magnified and complicated, wide-area protection system in the practical engineering application is more and more restricted by the communication level. Based on the concept of limitedness of wide-area protection system, the grid with complex structure is divided orderly in this paper, and fault identification and protection action are executed in each divided zone to reduce the pressure of the communication system. In protection zone, a new wide-area...

Microsoft System Center Data Protection Manager 2012

CERN Document Server

Buchannan, Steve; Gomaa, Islam

2013-01-01

This book is a Packt tutorial, walking the administrator through the steps needed to create real solutions to the problems and tasks faced when ensuring that their data is protected. This book is for network administrators, system administrators, backup administrators, or IT consultants who are looking to expand their knowledge on how to utilize DPM to protect their organization's data.

DOE Hydrogen Program: 2010 Annual Merit Review and Peer Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

2010-12-01

This document summarizes the comments provided by peer reviewers on hydrogen and fuel cell projects presented at the FY 2010 U.S. Department of Energy (DOE) Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting (AMR), held June 7-11, 2010 in Washington, D.C.

5 CFR 315.806 - Appeal rights to the Merit Systems Protection Board.

Science.gov (United States)

2010-01-01

... discrimination because of race, color, religion, sex, or national origin; or age (provided that at the time of... condition if the individual meets the definition of “handicapped person” as set forth in regulations of the...

Design and implementation based on the classification protection vulnerability scanning system

International Nuclear Information System (INIS)

Wang Chao; Lu Zhigang; Liu Baoxu

2010-01-01

With the application and spread of the classification protection, Network Security Vulnerability Scanning should consider the efficiency and the function expansion. It proposes a kind of a system vulnerability from classification protection, and elaborates the design and implementation of a vulnerability scanning system based on vulnerability classification plug-in technology and oriented classification protection. According to the experiment, the application of classification protection has good adaptability and salability with the system, and it also approves the efficiency of scanning. (authors)

Magnetic field generated by lightning protection system

Science.gov (United States)

Geri, A.; Veca, G. M.

1988-04-01

A lightning protection system for today's civil buildings must be electromagnetically compatible with the electronic equipment present in the building. This paper highlights a mathematic model which analyzes the electromagnetic effects in the environment in which the lightning protection system is. This model is developed by means of finite elements of an electrical circuit where each element is represented by a double pole circuit according to the trapezoidal algorithm developed using the finite difference method. It is thus possible to analyze the electromagnetic phenomena associated with the transient effects created by the lightning stroke even for a high-intensity current. Referring to an elementary system comprised of an air terminal, a down conductor, and a ground terminal, numerical results are here laid out.

Practical Approach on Lightning and Grounding Protection System

OpenAIRE

Shan Jose Varghese

2015-01-01

Lightning Protection and Grounding of Electrical and Mechanical equipment’s for the Protection of the Human Beings, Structure of the building and equipment protection, safe working of the Worker at Industry as per my latest practical knowledge in the site environment in extreme climatic condition of low lying areas of the Gulf Region in the challenging projects. All the conductor calculation, Lightning Risk Factor calculations, all the system information regarding the ...

Study on pulsed current cathodic protection in a simulated system

Energy Technology Data Exchange (ETDEWEB)

Yan, Milin; Li, Helin [Xi' an Jiao Tong Universitiy (China)]|[Tubular Goods Research Center of China National Petroleum Corp. (China); Qiu, Yubing; Guo, Xingpeng [Hua Zhong University of Science and Techonology (China)

2004-07-01

The pulsed current cathodic protection (PCCP) is a new cathodic protection (CP) technology and shows more advantages over the conventional DC cathodic protection (DCCP) in oil well casing system. However, little information about PCCP is reported. In this research, a simulated CP system was set up in a pool of 3.5 m x 2.0 m x 3.0 m size, in which the effects of the square wave pulsed current (SWPC) parameters (amplitude: IA, frequency: f, duty cycle: P), auxiliary anode distance (d) and media conductivity ({mu}) on the cathodic potential (E) distribution were studied, and the protection effects of PCCP and DCCP were compared. The results show that with increase of the square wave parameters (IA, f, P), the E distribution becomes more negative and the effects of each current parameter are relate closely to the cathode polarizing state. Only with suitable square wave parameters can the whole cathode be effectively protected. With increase of d and {mu}, the E distribution becomes more uniform. Compared with DCCP system, PCCP system has much more uniform E distribution, costs less average current, and gains much better protection effects. Further, the mechanism of PCCP was analyzed. (authors)

The Zernike expansion--an example of a merit function for 2D/3D registration based on orthogonal functions.

Science.gov (United States)

Dong, Shuo; Kettenbach, Joachim; Hinterleitner, Isabella; Bergmann, Helmar; Birkfellner, Wolfgang

2008-01-01

Current merit functions for 2D/3D registration usually rely on comparing pixels or small regions of images using some sort of statistical measure. Problems connected to this paradigm the sometimes problematic behaviour of the method if noise or artefacts (for instance a guide wire) are present on the projective image. We present a merit function for 2D/3D registration which utilizes the decomposition of the X-ray and the DRR under comparison into orthogonal Zernike moments; the quality of the match is assessed by an iterative comparison of expansion coefficients. Results in a imaging study on a physical phantom show that--compared to standard cross--correlation the Zernike moment based merit function shows better robustness if histogram content in images under comparison is different, and that time expenses are comparable if the merit function is constructed out of a few significant moments only.

Distance Protection for Microgrids in Distribution System

DEFF Research Database (Denmark)

Lin, Hengwei; Liu, Chengxi; Guerrero, Josep M.

2015-01-01

protection decreased. This paper adopts distance protection for one mid-voltage level microgrid in Aalborg, Denmark. Different operation modes of the network are analyzed and tested in the paper. The simulation results show that the variations of the fault currents seen by the forward relays are much larger...... than the backward relays. Meanwhile, the fault currents change little with the randomness of renewable energy except the intermittence. Finally, it shows that the designed distance protection has satisfactory performance to clear the various faults.......Owing to the increasing penetration of distributed generation, there are some challenges for the conventional protection in distribution system. Bidirectional power flow and variable fault current because of the various operation modes may lead to the selectivity and sensitivity of the overcurrent...

Merit pay: the Federal Government's pay-for-performance experience.

OpenAIRE

Holliman, Sherry Diane.

1983-01-01

Approved for public release; distribution is unlimited For many years, businesses in private industry have been utilizing and experimenting with various forms of performance-based pay. These innovations have been part of a continuing search by organizations for better approaches to administering pay. With the passing of the Civil Service Reform Act of 1978, the Federal Government began its form of this concept entitled, 'Merit Pay'. Although many studies have examined uses in the areas of ...

Nuclear whistleblower protection system in U.S. and its implication to Japanese regulatory system

International Nuclear Information System (INIS)

Tanabe, Tomoyuki; Suzuki, Tatsujiro

2003-01-01

The nuclear whistleblower protection system in U.S.A consists of two programs: 1) allegation program and 2) whistleblower protection system. The former is explained by basic act, definition of allegation, anonymous allegation, direct allegation to NRC (Nuclear Regulatory Commission), number of allegation from 1997 to 2001, procedure and period of investigation and notice of allegation to licensees. The latter is explained by basis act, outline of the system, enforcement by NRC and DOL (Department of Labor), number of discrimination compliant and anxiety of licensees. The system is good conditions in U.S.A depend on 1) prevent of illegal act and increase, 2) preparation of procedure and its transparency and 3) enforcement system. However, a hostile act to licensees is found in the whistleblower protection system. There are many problems in Japanese regulatory system. The improvement points of Japanese system are proposed. (S.Y.)

Circuit protection of ehv power systems from 150 to 765 kV

Energy Technology Data Exchange (ETDEWEB)

Geise, F; Jaeger, J

1965-11-01

Short tripping times required for all faults in ehv transmission systems are obtained by means of differential and comparative protection arrangements. It is essential that protection and communication systems be closely integrated and that special current transformers with linearized cores supply protective devices with correct measured values. By arranging filters between transformer and directional relay, it is possible to use capacitive voltage transformers for high speed protection. A description of power system with backup protection devices is presented.

Handover training: does one size fit all? The merits of mass customisation

NARCIS (Netherlands)

Kicken, Wendy; Van der Klink, Marcel; Barach, Paul; Boshuizen, Els

2012-01-01

Kicken, W., Van der Klink, M., Barach, P., & Boshuizen, H. P. A. (2012). Handover training: does one size fit all? The merits of mass customisation. British Medical Journal Quality & Safety, 21, i84-i88. doi:10.1136/bmjqs-2012-001164

ICRP Publication 138: Ethical Foundations of the System of Radiological Protection.

Science.gov (United States)

Cho, K-W; Cantone, M-C; Kurihara-Saio, C; Le Guen, B; Martinez, N; Oughton, D; Schneider, T; Toohey, R; ZöLzer, F

2018-02-01

Despite a longstanding recognition that radiological protection is not only a matter of science, but also ethics, ICRP publications have rarely addressed the ethical foundations of the system of radiological protection explicitly. The purpose of this publication is to describe how the Commission has relied on ethical values, either intentionally or indirectly, in developing the system of radiological protection with the objective of presenting a coherent view of how ethics is part of this system. In so doing, it helps to clarify the inherent value judgements made in achieving the aim of the radiological protection system as underlined by the Commission in Publication 103. Although primarily addressed to the radiological protection community, this publication is also intended to address authorities, operators, workers, medical professionals, patients, the public, and its representatives (e.g. NGOs) acting in the interest of the protection of people and the environment. This publication provides the key steps concerning the scientific, ethical, and practical evolutions of the system of radiological protection since the first ICRP publication in 1928. It then describes the four core ethical values underpinning the present system: beneficence/ non-maleficence, prudence, justice, and dignity. It also discusses how these core ethical values relate to the principles of radiological protection, namely justification, optimisation, and limitation. The publication finally addresses key procedural values that are required for the practical implementation of the system, focusing on accountability, transparency, and inclusiveness. The Commission sees this publication as a founding document to be elaborated further in different situations and circumstances.

Protective garment ventilation system

Science.gov (United States)

Lang, R. (Inventor)

1970-01-01

A method and apparatus for ventilating a protective garment, space suit system, and/or pressure suits to maintain a comfortable and nontoxic atmosphere within is described. The direction of flow of a ventilating and purging gas in portions of the garment may be reversed in order to compensate for changes in environment and activity of the wearer. The entire flow of the ventilating gas can also be directed first to the helmet associated with the garment.

Integration of the environment into the system of radiation protection

International Nuclear Information System (INIS)

Higley, K.

2018-01-01

In 2005 the International Commission on Radiological Protection (ICRP) embarked on an effort to ensure that the system for environmental radiological protection would be reconcilable with that for radiological protection of man, and with the approaches used for protection of the environment from other potential hazards

System Protection Schemes in Eastern Denmark

DEFF Research Database (Denmark)

Rasmussen, Joana

outages in the southern part of the 132-kV system introduce further stress in the power system, eventually leading to a voltage collapse. The local System Protection Scheme against voltage collapse is designed as a response-based scheme, which is dependent on local indication of reactive and active power...... effective measures, because they are associated with large reactive power losses in the transmission system. Ordered reduction of wind generation is considered an effective measure to maintain voltage stability in the system. Reactive power in the system is released due to tripping of a significant amount...... system. In that way, the power system capability could be extended beyond normal limits....

Distance Protection of Cross-Bonded Transmission Cable-Systems

DEFF Research Database (Denmark)

Bak, Claus Leth; F. Jensen, Christian

2014-01-01

In this paper the problems of protecting a cross-bonded cable system using distance protection are analysed. The combination of the desire to expand the high voltage transmission grid and the public's opinion towards new installations of overhead lines (OHL), more and more transmission cable syst...

Evolution of the system of radiological protection

International Nuclear Information System (INIS)

2004-01-01

The development of new radiological protection recommendations by the International Commission on Radiological Protection (ICRP) continues to be a strategically important undertaking, both nationally and internationally. With the growing recognition of the importance of stakeholder aspects in radiological protection decision making, regional and cultural aspects have also emerged as having potentially significant influence on how protection of the public, workers and the environment are viewed. Differing cultural aspects should therefore be considered by the ICRP in its development of new recommendations. Based on this assumption, the NEA organised the Asian Regional Conference on the Evolution of the System of Radiological Protection to express and explore views from the Far East. Held in Tokyo on 24-25 October 2002, the conference included presentations by the ICRP Chair as well as by radiological protection experts from Japan, the Republic of Korea, China and Australia. The distinct views and needs of these countries were discussed in the context of their regional and cultural heritages. These views, along with a summary of the conference results, are presented in these proceedings. (author)

Current developments on the coal and gas markets and their retroactive effects on the Merit Order; Aktuelle Entwicklungen auf den Kohle- und Gasmaerkten und ihre Rueckwirkungen auf die Merit Order

Energy Technology Data Exchange (ETDEWEB)

Hecking, Harald; Cam, Eren; Schoenfisch, Max; Schulte, Simon [ewi Energy Research and Scenarios gGmbH, Koeln (Germany)

2017-06-15

Coal and gas continue to play a significant role in the European power generation system, especially in Germany. According to the AG energy balances, the share of hard coal in German gross electricity generation in 2016 was 17.2% and natural gas 12.4%. In addition to the CO{sub 2} price, the prices for steam coal and natural gas are a key factor in determining which gas or coal power station is in Merit Order and whether it comes to a fuel switch. Declining gas prices have been rising sharply since the middle of 2016, and the volatile prices for steam coal have been rising. This article discusses the developments and factors responsible for these developments, which could be expected in the near future, and the implications for the gas-coal spread in the electricity market. [German] Kohle und Gas spielen weiterhin eine bedeutende Rolle im europaeischen Stromerzeugungssystem, insbesondere in Deutschland. Laut AG Energiebilanzen lag 2016 der Anteil der Steinkohle an der deutschen Bruttostromerzeugung bei 17,2 % und der von Erdgas bei 12,4 %. Neben dem CO{sub 2}-Preis sind die Preise fuer Kesselkohle und Erdgas massgeblich dafuer verantwortlich, welches Gas- bzw. Kohlekraftwerk welche Position in der Merit Order einnimmt und ob es zu einem Fuel Switch kommt. Sinkende Preise beim Gas stehen seit Mitte 2016 stark gestiegenen und volatilen Preisen fuer Kesselkohle gegenueber. Dieser Artikel diskutiert, welche Entwicklungen und Faktoren fuer diese Entwicklungen verantwortlich sind, womit in naher Zukunft zu rechnen sein koennte und welche Implikationen dies fuer den Gas-Kohle-Spread im Strommarkt hat.

Fault Identification Algorithm Based on Zone-Division Wide Area Protection System

Directory of Open Access Journals (Sweden)

Xiaojun Liu

2014-04-01

Full Text Available As the power grid becomes more magnified and complicated, wide-area protection system in the practical engineering application is more and more restricted by the communication level. Based on the concept of limitedness of wide-area protection system, the grid with complex structure is divided orderly in this paper, and fault identification and protection action are executed in each divided zone to reduce the pressure of the communication system. In protection zone, a new wide-area protection algorithm based on positive sequence fault components directional comparison principle is proposed. The special associated intelligent electronic devices (IEDs zones which contain buses and transmission lines are created according to the installation location of the IEDs. When a fault occurs, with the help of the fault information collecting and sharing from associated zones with the fault discrimination principle defined in this paper, the IEDs can identify the fault location and remove the fault according to the predetermined action strategy. The algorithm will not be impacted by the load changes and transition resistance and also has good adaptability in open phase running power system. It can be used as a main protection, and it also can be taken into account for the back-up protection function. The results of cases study show that, the division method of the wide-area protection system and the proposed algorithm are effective.

Enhanced personal protection system for the PS

CERN Multimedia

Caroline Duc

2013-01-01

During the first long shutdown (LS1) a new safety system will be installed in the primary beam areas of the PS complex in order to bring the standard of personnel radiation protection at the PS into line with that of the LHC.   Pierre Ninin, deputy group leader of GS-ASE and responsible for the installation of the new PS complex safety system, in front of a new access control system. The LHC access control systems are state-of-the-art, whereas those of the injection chain accelerators were running the risk of becoming obsolete. For the past two years a project to upgrade the access and safety systems of the first links in the LHC accelerator chain has been underway to bring them into compliance with nuclear safety standards. These systems provide the personnel with automatic protection by limiting access to hazardous areas and by ensuring that nobody is present in the areas when the accelerator is in operation. By the end of 2013, the project teams will ha...

Reliability Analysis Study of Digital Reactor Protection System in Nuclear Power Plant

International Nuclear Information System (INIS)

Guo, Xiao Ming; Liu, Tao; Tong, Jie Juan; Zhao, Jun

2011-01-01

The Digital I and C systems are believed to improve a plants safety and reliability generally. The reliability analysis of digital I and C system has become one research hotspot. Traditional fault tree method is one of means to quantify the digital I and C system reliability. Review of advanced nuclear power plant AP1000 digital protection system evaluation makes clear both the fault tree application and analysis process to the digital system reliability. One typical digital protection system special for advanced reactor has been developed, which reliability evaluation is necessary for design demonstration. The typical digital protection system construction is introduced in the paper, and the process of FMEA and fault tree application to the digital protection system reliability evaluation are described. Reliability data and bypass logic modeling are two points giving special attention in the paper. Because the factors about time sequence and feedback not exist in reactor protection system obviously, the dynamic feature of digital system is not discussed

Protection of Distribution Systems with Distributed Energy Resources

DEFF Research Database (Denmark)

Bak-Jensen, Birgitte; Browne, Matthew; Calone, Roberto

of 17 months of work of the Joint Working Group B5/C6.26/CIRED “Protection of Distribution Systems with Distributed Energy Resources”. The working group used the CIGRE report TB421 “The impact of Renewable Energy Sources and Distributed Generation on Substation Protection and Automation”, published...... by WG B5.34 as the entry document for the work on this report. In doing so, the group aligned the content and the scope of this report, the network structures considered, possible islanding, standardized communication and adaptive protection, interface protection, connection schemes and protection...... are listed (chapter 3). The first main part of the report starts with a summary of the backgrounds on DER and current practices in protection at the distribution level (chapter 4). This chapter contains an analysis of CIGRE TB421, protection relevant characteristics of DER, a review of current practices...

Distribution system protection with communication technologies

DEFF Research Database (Denmark)

Wei, Mu; Chen, Zhe

2010-01-01

Due to the communication technologies’ involvement in the distribution power system, the time-critical protection function may be implemented more accurately, therefore distribution power systems’ stability, reliability and security could be improved. This paper presents an active distribution...

Magnetothermoelectric figure of merit of Co/Cu multilayers

Energy Technology Data Exchange (ETDEWEB)

Hu, X. K., E-mail: xiukun.hu@ptb.de; Krzysteczko, P.; Liebing, N.; Schumacher, H. W. [Physikalisch-Technische Bundesanstalt, Bundesallee 100, D-38116 Braunschweig (Germany); Serrano-Guisan, S. [International Iberian Nanotechnology Laboratory, Av. Mestre José Veiga, 4715-330 Braga (Portugal); Rott, K.; Reiss, G. [Fakultät für Physik, Universität Bielefeld, Postfach 100131, D-33501 Bielefeld (Germany); Kimling, J.; Böhnert, T.; Nielsch, K. [Institut für Angewandte Physik, Universität Hamburg, Jungiusstraße 11, D-20355 Hamburg (Germany)

2014-03-03

The switching of the magnetic configuration of giant magnetoresistance multilayers not only changes the electrical and thermal conductivities but also the thermopower. We study the magnetotransport and the magnetothermoelectric properties of Co/Cu multilayer devices in a lateral thermal gradient. The Seebeck coefficient reaches values up to −18 μV/K at room temperature and shows a magnetic field dependence up to 28.6% upon spin reversal. In combination with thermal conductivity data of the same Co/Cu stack, we find a magnetothermoelectric figure of merit of up to 65%. Furthermore, a magneto-power factor of up to 110% is derived.

Advanced worker protection system. Topical report, Phase I

Energy Technology Data Exchange (ETDEWEB)

Myers, J.

1995-07-01

The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D&D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D&D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D&D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project will result in the development of an Advanced Worker Protection System (AWPS). The AWPS will be built around a life support backpack that uses liquid air to provide cooling as well as breathing gas to the worker. The backpack will be combined with advanced protective garments, advanced liquid cooling garment, respirator, communications, and support equipment to provide improved worker protection, simplified system, maintenance, and dramatically improve worker productivity through longer duration work cycles.

OPTIMIZING THE DESIGN OF THE SYSTEMS OF INFORMATION PROTECTION IN AUTOMATED INFORMATIONAL SYSTEMS OF INDUSTRIAL ENTERPRISES

Directory of Open Access Journals (Sweden)

I. E. L'vovich

2014-01-01

Full Text Available Summary. Now to increase of indicators of efficiency and operability of difficult systems apply an automation equipment. The increasing role of information which became universal goods for relationship between various structures is noted. The question of its protection becomes the most actual. Special value is allocated for optimum design at creation of systems of the protection, allowing with the greatest probability to choose the best decisions on a set of alternatives. Now it becomes actual for the majority of the industrial enterprises as correctly designed and introduced system of protection will be pledge of successful functioning and competitiveness of all organization. Stages of works on creation of an information security system of the industrial enterprise are presented. The attention is focused on one of the most important approaches to realization of optimum design – multialternative optimization. In article the structure of creation of system of protection from the point of view of various models is considered, each of which gives an idea of features of design of system as a whole. The special attention is paid to a problem of creation of an information security system as it has the most difficult structure. Tasks for processes of automation of each of design stages of system of information security of the industrial enterprises are designated. Idea of each of stages of works is given at design of system of protection that allows to understand in the best way internal structure of creation of system of protection. Therefore, it is given the chance of evident submission of necessary requirements to creation of a reliable complex of information security of the industrial enterprise. Thereby it is given the chance of leveling of risks at early design stages of systems of protection, the organization and definition of necessary types of hardware-software complexes for future system.

Using the graphs models for evaluating in-core monitoring systems reliability by the method of imiting simulaton

International Nuclear Information System (INIS)

Golovanov, M.N.; Zyuzin, N.N.; Levin, G.L.; Chesnokov, A.N.

1987-01-01

An approach for estimation of reliability factors of complex reserved systems at early stages of development using the method of imitating simulation is considered. Different types of models, their merits and lacks are given. Features of in-core monitoring systems and advosability of graph model and graph theory element application for estimating reliability of such systems are shown. The results of investigation of the reliability factors of the reactor monitoring, control and core local protection subsystem are shown

Fire protection system operating experience review for fusion applications

International Nuclear Information System (INIS)

Cadwallader, L.C.

1995-12-01

This report presents a review of fire protection system operating experiences from particle accelerator, fusion experiment, and other applications. Safety relevant operating experiences and accident information are discussed. Quantitative order-of-magnitude estimates of fire protection system component failure rates and fire accident initiating event frequencies are presented for use in risk assessment, reliability, and availability studies. Safety concerns with these systems are discussed, including spurious operation. This information should be useful to fusion system designers and safety analysts, such as the team working on the Engineering Design Activities for the International Thermonuclear Experimental Reactor

Fire protection system operating experience review for fusion applications

Energy Technology Data Exchange (ETDEWEB)

Cadwallader, L.C.

1995-12-01

This report presents a review of fire protection system operating experiences from particle accelerator, fusion experiment, and other applications. Safety relevant operating experiences and accident information are discussed. Quantitative order-of-magnitude estimates of fire protection system component failure rates and fire accident initiating event frequencies are presented for use in risk assessment, reliability, and availability studies. Safety concerns with these systems are discussed, including spurious operation. This information should be useful to fusion system designers and safety analysts, such as the team working on the Engineering Design Activities for the International Thermonuclear Experimental Reactor.

The clinical case report: a review of its merits and limitations.

Science.gov (United States)

Nissen, Trygve; Wynn, Rolf

2014-04-23

The clinical case report has a long-standing tradition in the medical literature. While its scientific significance has become smaller as more advanced research methods have gained ground, case reports are still presented in many medical journals. Some scholars point to its limited value for medical progress, while others assert that the genre is undervalued. We aimed to present the various points of view regarding the merits and limitations of the case report genre. We searched Google Scholar, PubMed and select textbooks on epidemiology and medical research for articles and book-chapters discussing the merits and limitations of clinical case reports and case series. The major merits of case reporting were these: Detecting novelties, generating hypotheses, pharmacovigilance, high applicability when other research designs are not possible to carry out, allowing emphasis on the narrative aspect (in-depth understanding), and educational value. The major limitations were: Lack of ability to generalize, no possibility to establish cause-effect relationship, danger of over-interpretation, publication bias, retrospective design, and distraction of reader when focusing on the unusual. Despite having lost its central role in medical literature in the 20th century, the genre still appears popular. It is a valuable part of the various research methods, especially since it complements other approaches. Furthermore, it also contributes in areas of medicine that are not specifically research-related, e.g. as an educational tool. Revision of the case report genre has been attempted in order to integrate the biomedical model with the narrative approach, but without significant success. The future prospects of the case report could possibly be in new applications of the genre, i.e. exclusive case report databases available online, and open access for clinicians and researchers.

A New GPS-based Digital Protection System for Smart Grids in Loop Structure

Directory of Open Access Journals (Sweden)

X. Liu

2014-12-01

Full Text Available This paper presents a new digital protection system to solve the protection challenges in future smart grids, i.e., fast protection and fault isolation in a loop-structured system with limited magnitude of fault current. The new system combines two protection algorithms, i.e., a differential protection as the primary algorithm and an overcurrent protection as the backup one. The new system uses real-time Ethernet and digital data acquisition techniques to overcome the restriction on data transmission over large grids. The current measurements at different locations are time-synchronized by GPS clocks, and then transmitted to a central computer via the Ethernet. As opposed to digital relays which often contain PMU functionality nowadays, this approach uses time stamps on the instantaneous current values. We build a prototype of the new system on a test-bed. The results from simulations and experiments have demonstrated that the protection system achieves fast and accurate protection.

Design and operation of the quench protection system for the Fermilab tevatron

International Nuclear Information System (INIS)

Martin, P.S.

1989-01-01

The operation of a superconducting accelerator, in addition to cryogenic requirements, introduces a new complexity not present in a conventional accelerator. A method is required for protecting the magnets from possible overheating or overvoltage conditions in the event that some magnets quench, that is, are elevated in temperature so that they are no longer superconducting. The development of that system is the topic of this chapter. Any quench protection system has two very important ingredients. First, it must be designed with sufficient integrity to remain functional even under abnormal circumstances. The magnets must be protected during power failures, for example. Quenches involving a large number of components can also be hazardous because of the redistribution of voltages during the quench. Some of the system integrity can be achieved through redundancy. Frequent testing of critical elements of the system also assures the overall integrity. Second, the quench protection system must protect against damage from quenches regardless of their location or the excitation current at the time. It is not sufficient to protect just the magnet coils; either the leads between magnets must be fully stabilized or the quench protection system must protect them. The next section presents a brief discussion of the basic properties of superconductors and the phenomenon of quench propagation. 10 references, 13 figures

New evaluation system for antisabotage physical protection

International Nuclear Information System (INIS)

Itakura, Shuichiro; Nakagome, Yoshihiro

2008-01-01

The discussion on an appropriate level of physical protection has not been elaborated so far because of the confidentiality of its nature, thus resulting in a lack of consensus on this issue. In view of this context, a new system for the evaluation of antisabotage physical protection systems is proposed in this paper, in which we introduce openness to a certain extent in the process of the evaluation. The proposed system is composed of the following three elements; (1) establishment of an evaluation basis threat (EBT), which should be less strong but more likely to occur than the design basis threat (DBT); (2) employment of realistic standard scenarios in the process of evaluation; (3) disclosure of results of evaluation implemented based on the above EBT and standard scenarios. It is expected that this considerably open system will foment peace of mind among citizens as well as create a deterrent effect that would minimize the occurrence of sabotage on nuclear facilities. (author)

Quantitative evaluation of physical protection system in nuclear power plant

International Nuclear Information System (INIS)

Sun Yahua; Li Bin; Li Shiju

2009-01-01

Based on the prompt detection analysis, this paper introduced one analysis model of intrusion path in nuclear power plant by means of morphology analysis and developed the evaluation software for path model analysis of physical protection system. Quantitative analysis on three elements (detection, delay, and response) of physical protection system was presented with an imaginary intrusion event example in Mac Arthur nuclear center. The results indicated that the path prompt detection analysis worked effectively to find the weak point of the physical protection system in NPP, and meantime we can also get the high cost-effectiveness improved measures. It is an effective approach to evaluate the overall performance of the system. (authors)

75 FR 22165 - Publication of Open Government Directive

Science.gov (United States)

2010-04-27

... MERIT SYSTEMS PROTECTION BOARD Publication of Open Government Directive AGENCY: U.S. Merit Systems... specific actions are: (1) Publication of three high- value data sets; (2) designation of a senior agency... Open Government Web page; and (4) development and publication of an Open Government Plan. The Directive...

Preliminary Uncertainty Analysis for SMART Digital Core Protection and Monitoring System

International Nuclear Information System (INIS)

Koo, Bon Seung; In, Wang Kee; Hwang, Dae Hyun

2012-01-01

The Korea Atomic Energy Research Institute (KAERI) developed on-line digital core protection and monitoring systems, called SCOPS and SCOMS as a part of SMART plant protection and monitoring system. SCOPS simplified the protection system by directly connecting the four RSPT signals to each core protection channel and eliminated the control element assembly calculator (CEAC) hardware. SCOMS adopted DPCM3D method in synthesizing core power distribution instead of Fourier expansion method being used in conventional PWRs. The DPCM3D method produces a synthetic 3-D power distribution by coupling a neutronics code and measured in-core detector signals. The overall uncertainty analysis methodology which is used statistically combining uncertainty components of SMART core protection and monitoring system was developed. In this paper, preliminary overall uncertainty factors for SCOPS/SCOMS of SMART initial core were evaluated by applying newly developed uncertainty analysis method

Multi Agent System Based Adaptive Protection for Dispersed Generation Integrated Distribution Systems

DEFF Research Database (Denmark)

Liu, Leo; Rather, Zakir Hussain; Bak, Claus Leth

2013-01-01

The increasing penetration of dispersed generation (DG) brings challenges to conventional protection approaches of distribution system, mainly due to bi-directional power flow and variable fault current contribution from different generation technology-based DG units. Moreover, the trend......) is proposed. The adaptive protection intelligently adopts suitable settings for the variation of fault current from diversified DG units. Furthermore, the structure of mobile MAS with additional flexibility is capable of adapting the changes of system topology in a short period, e.g. radial/meshed, grid...

Europe's contribution to implementation of a radiation protection system

International Nuclear Information System (INIS)

Lecomte, J.F.

2010-01-01

What is commonly referred to as a radiation protection system is a range of scientific considerations, principles and rules, the aim of which is to contribute to an appropriate level of protection of individuals and the environment against the harmful effects of exposure to ionising radiation, without excessively limiting desirable human activities which can be associated with such exposure (see ICRP Publication 103). This system is essentially based on an international consensus. The European level only concerns the Member States of the Union but it is crucial that it constitute the final, legally binding step prior to the definition of national regulations. The European radiation protection system (the EURATOM Treaty and its derived legislation) is presented below, not from the legal perspective but from a contextual viewpoint. Research activities are not discussed here. (author)

The capacity of Australia's protected-area system to represent threatened species.

Science.gov (United States)

Watson, James E M; Evans, Megan C; Carwardine, Josie; Fuller, Richard A; Joseph, Liana N; Segan, Dan B; Taylor, Martin F J; Fensham, R J; Possingham, Hugh P

2011-04-01

The acquisition or designation of new protected areas is usually based on criteria for representation of different ecosystems or land-cover classes, and it is unclear how well-threatened species are conserved within protected-area networks. Here, we assessed how Australia's terrestrial protected-area system (89 million ha, 11.6% of the continent) overlaps with the geographic distributions of threatened species and compared this overlap against a model that randomly placed protected areas across the continent and a spatially efficient model that placed protected areas across the continent to maximize threatened species' representation within the protected-area estate. We defined the minimum area needed to conserve each species on the basis of the species' range size. We found that although the current configuration of protected areas met targets for representation of a given percentage of species' ranges better than a random selection of areas, 166 (12.6%) threatened species occurred entirely outside protected areas and target levels of protection were met for only 259 (19.6%) species. Critically endangered species were among those with the least protection; 12 (21.1%) species occurred entirely outside protected areas. Reptiles and plants were the most poorly represented taxonomic groups, and amphibians the best represented. Spatial prioritization analyses revealed that an efficient protected-area system of the same size as the current protected-area system (11.6% of the area of Australia) could meet representation targets for 1272 (93.3%) threatened species. Moreover, the results of these prioritization analyses showed that by protecting 17.8% of Australia, all threatened species could reach target levels of representation, assuming all current protected areas are retained. Although this amount of area theoretically could be protected, existing land uses and the finite resources available for conservation mean land acquisition may not be possible or even effective

Robotic system for the servicing of the orbiter thermal protection system

Science.gov (United States)

Graham, Todd; Bennett, Richard; Dowling, Kevin; Manouchehri, Davoud; Cooper, Eric; Cowan, Cregg

1994-01-01

This paper describes the design and development of a mobile robotic system to process orbiter thermal protection system (TPS) tiles. This work was justified by a TPS automation study which identified tile rewaterproofing and visual inspection as excellent applications for robotic automation.

Expert systems for protective monitoring of facilities

International Nuclear Information System (INIS)

Carr, K.R.

1987-01-01

In complex plants, the possibility of serious operator error always exists to some extent, but, this can be especially true during an experiment or some other unusual exercise. Possible contributing factors to operational error include personnel fatigue, misunderstanding in communication, mistakes in executing orders, uncertainty about the delegated authority, pressure to meet a demanding schedule, and a lack of understanding of the possible consequences of deliberate violations of the facility's established operating procedures. Authoritative reports indicate that most of these factors were involved in the disastrous Russian Chernobyl-4 nuclear reactor accident in April 1986, which, ironically, occurred when a safety experiment was being conducted. Given the computer hardware and software now available for implementing expert systems together with integrated signal monitoring and communications, plant protection could be enhanced by an expert system with extended features to monitor the plant. The system could require information from the operators on a rigidly enforced schedule and automatically log in and report on a scheduled time basis to authorities at a central remote site during periods of safe operation. Additionally, the system could warn an operator or automatically shut down the plant in case of dangerous conditions, while simultaneously notifying independent, responsible, off-site personnel of the action taken. This approach would provide protection beyond that provided by typical facility scram circuits. This paper presents such an approach to implementing an expert system for plant protection, together with specific hardware and software configurations. The Chernobyl accident is used as the basis of discussion

3. Promotion of environment protection of sea and near-sea region. Swinoujscie 12-14 October 1994

International Nuclear Information System (INIS)

1994-01-01

The great number of problems connected with environment protection near shore marine zone, beach protection, effluent transport in ground and surface waters in region of North Port of Poland as well as technical solutions of water purification and legal problems have been discussed during the conference. All observations and experimental works have been carried out in that region. Among reported works two of them have been devoted to application of nuclear methods in interesting merit

Analytical model and figures of merit for filtered Microwave Photonic Links.

Science.gov (United States)

Gasulla, Ivana; Capmany, José

2011-09-26

The concept of filtered Microwave Photonic Links is proposed in order to provide the most general and versatile description of complex analog photonic systems. We develop a field propagation model where a global optical filter, characterized by its optical transfer function, embraces all the intermediate optical components in a linear link. We assume a non-monochromatic light source characterized by an arbitrary spectral distribution which has a finite linewidth spectrum and consider both intensity modulation and phase modulation with balanced and single detection. Expressions leading to the computation of the main figures of merit concerning the link gain, noise and intermodulation distortion are provided which, to our knowledge, are not available in the literature. The usefulness of this derivation resides in the capability to directly provide performance criteria results for complex links just by substituting in the overall closed-form formulas the numerical or measured optical transfer function characterizing the link. This theory is presented thus as a potential tool for a wide range of relevant microwave photonic application cases which is extendable to multiport radio over fiber systems. © 2011 Optical Society of America

Joint force protection advanced security system (JFPASS) "the future of force protection: integrate and automate"

Science.gov (United States)

Lama, Carlos E.; Fagan, Joe E.

2009-09-01

The United States Department of Defense (DoD) defines 'force protection' as "preventive measures taken to mitigate hostile actions against DoD personnel (to include family members), resources, facilities, and critical information." Advanced technologies enable significant improvements in automating and distributing situation awareness, optimizing operator time, and improving sustainability, which enhance protection and lower costs. The JFPASS Joint Capability Technology Demonstration (JCTD) demonstrates a force protection environment that combines physical security and Chemical, Biological, Radiological, Nuclear, and Explosive (CBRNE) defense through the application of integrated command and control and data fusion. The JFPASS JCTD provides a layered approach to force protection by integrating traditional sensors used in physical security, such as video cameras, battlefield surveillance radars, unmanned and unattended ground sensors. The optimization of human participation and automation of processes is achieved by employment of unmanned ground vehicles, along with remotely operated lethal and less-than-lethal weapon systems. These capabilities are integrated via a tailorable, user-defined common operational picture display through a data fusion engine operating in the background. The combined systems automate the screening of alarms, manage the information displays, and provide assessment and response measures. The data fusion engine links disparate sensors and systems, and applies tailored logic to focus the assessment of events. It enables timely responses by providing the user with automated and semi-automated decision support tools. The JFPASS JCTD uses standard communication/data exchange protocols, which allow the system to incorporate future sensor technologies or communication networks, while maintaining the ability to communicate with legacy or existing systems.

Study on aging management of fire protection system in nuclear power plant

International Nuclear Information System (INIS)

Fang Huasong; Du Yu; Li Jianwen; Shi Haining; Tu Fengsheng

2010-01-01

Fire prevention, fire fighting and fire automatic alarms are three aspects which be included in fire protection system in nuclear power plants. The fire protection system can protect personnel, equipment etc in the fire, so their performance will have a direct influence on the safe operation in nuclear power plants. The disabled accidents caused by aging have happened continuously with the extension of time in the fire protection system, which is the major security risk during the running time in nuclear power plants. In view of the importance of fire protection system and the severity of aging problems, the aging are highly valued by the plant operators and related organizations. Though the feedback of operating experience in nuclear power plant, the impact of the fire-fighting equipment aging on system performance and reliability be assessed, the aging sensitive equipment be selected to carry out the aging analysis and to guide the management and maintenance to guarantee the healthy operation in life time of fire protection system in nuclear power plant. (authors)

Fire protection countermeasures for containment ventilation systems

International Nuclear Information System (INIS)

Alvares, N.J.; Beason, D.G.; Bergman, W.; Ford, H.W.; Lipska, A.E.

1980-01-01

The goal of this project is to find countermeasures to protect HEPA filters in exit ventilation ducts from the heat and smoke generated by fire. Several methods for partially mitigating the smoke exposure to the HEPA filters were identified through testing and analysis. These independently involve controlling the fuel, controlling the fire, and intercepting the smoke aerosol prior to its sorption on the HEPA filter. Exit duct treatment of aerosols is not unusual in industrial applications and involves the use of scrubbers, prefilters, and inertial impaction, depending on the size, distribution, and concentration of the subject aerosol. However, when these unmodified techniques were applied to smoke aerosols from fires on materials, common to experimental laboratories of LLNL, it was found they offered minimal protection to the HEPA filters. Ultimately, a continuous, movable, high-efficiency prefilter using modified commercial equipment was designed. This technique is capable of protecting HEPA filters over the total duration of the test fires. The reason for success involved the modificaton of the prefiltration media. Commercially available filter media has a particle sorption efficiency that is inversely proportional to media strength. To achieve properties of both efficiency and strength, we laminated rolling filter media with the desired properties. It is not true that the use of rolling prefilters solely to protect HEPA filters from fire-generated smoke aerosols is cost effective in every type of containment system, especially if standard fire-protection systems are available in the space. But in areas of high fire risk, where the potential fuel load is large and ignition sources are plentiful, the complication of a rolling prefilter in exit ventilation ducts to protect HEPA filters from smoke aerosols is definitely justified

Merits and difficulties in adopting codes, standards and nuclear regulations

International Nuclear Information System (INIS)

El-Saiedi, A.F.; Morsy, S.; Mariy, A.

1978-01-01

Developing countries planning for introducing nuclear power plants as a source of energy have to develop or adopt sound regulatory practices. These are necessary to help governmental authorities to assess the safety of nuclear power plants and to perform inspections needed to confirm the established safe and sound limits. The first requirement is to form an independent regulatory body capable of setting up and enforcing proper safety regulations. The formation of this body is governed by several considerations related to local conditions in the developing countries, which may not always be favourable. It is quite impractical for countries with limited experience in the nuclear power field to develop their own codes, standards and regulations required for the nuclear regulatory body to perform its tasks. A practical way is to adopt codes, standards and regulations of a well-developed country. This has merits as well as drawbacks. The latter are related to problems of personnel, software, equipment and facilities. The difficulties involved in forming a nuclear regulatory body, and the merits and difficulties in adopting foreign codes, standards and regulations required for such body to perform its tasks, are discussed in this paper. Discussions are applicable to many developing countries and particular emphasis is given to the conditions and practices in Egypt. (author)

Technological measures of protection in the copyright system

Directory of Open Access Journals (Sweden)

Radovanović Sanja

2011-01-01

Full Text Available Digital exploitation of works often exceed the limit to which the holder can control the exploitation of their intellectual creations, and the protection provided by legal norms are, in the era of a fast exchange of information, may prove to be insufficiently effective. For these reasons, the rights holders are increasingly opting for preventive care through placement of physical obstacles to the exploitation of copyright works, generic called technological protection measures (known as digital right management (DRM. Simultaneously with the development of the application of these measures flows the process of finding ways to circumvent them. Therefore, the effectiveness of technological measures depends on exactly the question of their legal protection, which now exists in most of modern legal systems. However, in the normative solutions there are differences, which reflect the problems in finding adequate forms of protection. They mostly stem from the fact that the sanctioning of circumvention (or preparatory actions of technological measures put into the question the purpose of copyright protection in general. Hence, in this paper we tried to point out the normative solutions accepted in modern legal systems and practical implications of what they have. Conclusion that arises is that the legal shaping of technological measures is not completed and that further technological developments open new dilemmas.

Plasmonic Refractive Index Sensor with High Figure of Merit Based on Concentric-Rings Resonator

Science.gov (United States)

Zhang, Zhaojian; Yang, Junbo; He, Xin; Zhang, Jingjing; Huang, Jie; Chen, Dingbo; Han, Yunxin

2018-01-01

A plasmonic refractive index (RI) sensor based on metal-insulator-metal (MIM) waveguide coupled with concentric double rings resonator (CDRR) is proposed and investigated numerically. Utilizing the novel supermodes of the CDRR, the FWHM of the resonant wavelength can be modulated, and a sensitivity of 1060 nm/RIU with high figure of merit (FOM) 203.8 is realized in the near-infrared region. The unordinary modes, as well as the influence of structure parameters on the sensing performance, are also discussed. Such plasmonic sensor with simple framework and high optical resolution could be applied to on-chip sensing systems and integrated optical circuits. Besides, the special cases of bio-sensing and triple rings are also discussed. PMID:29300331

Traditional land use and reconsideration of environmental zoning in the Hawf Protected Area, south-eastern Yemen

NARCIS (Netherlands)

Slecht, E.; Zaballos, L.G.H.; Quiroz Villarreal, D.K.; Scholte, P.; Buerkert, A.

2014-01-01

The Al Hawf area at the Yemen–Oman border hosts a unique fog-derived ecosystem which, due to its high diversity of plant and animal species, merits protection. Given the area's remoteness, poor infrastructure, high population growth and limited exchanges across the Omani border, the local

Mechanisms of protection of information in computer networks and systems

Directory of Open Access Journals (Sweden)

Sergey Petrovich Evseev

2011-10-01

Full Text Available Protocols of information protection in computer networks and systems are investigated. The basic types of threats of infringement of the protection arising from the use of computer networks are classified. The basic mechanisms, services and variants of realization of cryptosystems for maintaining authentication, integrity and confidentiality of transmitted information are examined. Their advantages and drawbacks are described. Perspective directions of development of cryptographic transformations for the maintenance of information protection in computer networks and systems are defined and analyzed.

Evaluation of road-transit physical protection systems

International Nuclear Information System (INIS)

Gallagher, R.J.; Keeton, S.C.; Stimmell, K.G.; DeLaquil, P. III.

1978-05-01

To assess the overall effectiveness of a transportation physical protection system, computer codes which simulate armed attacks have been developed and are being used to examine a range of issues associated with road transportation systems. The paper discusses the purpose and features of three of these codes, SOURCE (which simulates the initial ambush), SABRES I (which covers the battle) and BARS (which treats the penetration of protective cargo barriers). The use of these methodologies to evaluate the value of additional vehicles, guards, armor and alternative tactics or equipment as a means of improving convoy security has recently been completed. The results which are presented demonstrate that the protection offered by the present commercial regulations for guards and vehicles is probably marginal. This could be substantially increased by the addition of armor to close escort vehicles instead of just the transporter and the use of appropriate tactics. Against the baseline threat of adversaries armed with M-16's, observation and harassment from a modest distance until re-enforcements arrive appears preferable to aggressive assault by the ambushed guard force

Addressing Circuitous Currents MVDC Power Systems Protection

Science.gov (United States)

2017-12-31

Addressing Circuitous Currents MVDC Power Systems Protection 5b. GRANT NUMBER N00014-16-1-3113 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR($) Sd. PROJECT NUMBER...efficiency. A challenge with DC distribution is electrical protection . Z-source DC breakers alt! an pti n b&i g cvr.sidcrcd and this w rk ~xplores...zonal distribution, electric ship 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF a. REPORT b. ABSTRACT c. THIS PAGE ABSTRACT u u u uu 18. NUMBER

A demonstrator for an integrated subway protection system

Science.gov (United States)

Detoma, E.; Capetti, P.; Casati, G.; Billington, S.

2008-04-01

In 2006 SEPA has carried on the installation and tests of a demonstrator for an integrated subway protection system at a new subway station in the Naples, Italy) metropolitan area. Protection of a subway system is a difficult task given the amount of passengers transported every day. The demonstrator has been limited to non-intrusive detection techniques not to impair the passenger flow into the station. The demonstrator integrates several technologies and products that have been developed by SEPA or are already available on the market (MKS Instruments,...). The main purpose is to provide detection capabilities for attempts to introduce radioactive substances in the subway station, in order to foil possible attempts to place a dirty bomb, and threat detection and identification following release of chemical agents. The system integrates additional sensors such as video surveillance cameras and air flow sensing to complement the basic sensors suite. The need to protect sensitive installations such as subway stations has been highlighted by the series of terroristics actions carried out in recent years in the subway in London. However, given the number of passengers of a metro system, it is impossible to propose security techniques operating in ways similar to the screening of passengers in airports. Passengers screening and threat detection and identification must be quick, non-intrusive and capable of screening a large number of passengers to be applicable to mass transit systems. In 2005 SEPA, a small company operating in the field of trains video-surveillance systems and radiation detectors, started developing an integrated system to provide a comprehensive protection to subway stations, based on ready available or off-the-shelf components in order to quickly develop a reliable system with available technology. We ruled out at the beginning any new development in order to speed up the fielding of the system in less than one year. The system was developed with

Modernization of the physical protection system of IPEN-CNEN/SP

International Nuclear Information System (INIS)

Suzuki, F.F.

2001-01-01

Full text: The plans of physical protection of nuclear facilities must be reviewed and updated every two years. A general study of the physical protection system was carried out in order to review and to update the plan of physical protection of IPEN-CNEN/SP. Important alterations accomplished at the institute were considered in the study, as the installation of a cyclotron 30 MeV and the new operation conditions for the nuclear research reactor IEA-RI, that include the increase of its operation power from two to five megawatts and the establishment of the continuous operation by 72 hours weekly. The area of IPEN-CNEN/SP is 478,000 m 2 (101,850 m 2 built area of 107 constructions). The group responsible for the study investigated the performance of the physical protection system and detected some points that could be reinforced at inner and protected areas. The initial step was the evaluation, in loco, of the constructions and physical barriers of inner and protected areas. The performance of the security force personnel on the conventional procedures, as access control to the facilities, control of material flow, area monitoring and patrol, as well as its response for special situation procedures in the case of a physical protection emergency, were evaluated too. The study also focused the communication means used by the security force, as the extension phone lines that are located in each entrance area and in the huts, and the portable VHP radios that are used by the guards. In order to elaborate a programme of modernization of the physical protection system, using the results of the study as basis, an internal committee composed of specialists in physical protection, nuclear safety, operation of reactors and engineering areas was created. The programme elaborated by the committee strengthens the physical protection system by applying the defense in depth concept. At the same time, it attempts to propitiate a balanced protection to minimize the consequences for

Seabed Protection Systems to prevent Scour from High-Speed Ships

OpenAIRE

Evans, G

2010-01-01

This document reviews the scour protection systems required around port structures where these are to be used for the berthing of vessels powered by water jet systems. The development of a scour protection system at Poole Harbour in Dorset has been documented and reviewed and a series of laboratory investigations were then undertaken. This has enabled a greater understanding of the scour mechanisms from the water jet propulsion systems of High Speed Ships. This work has shown t...

Islands Unto Themselves: How Merit Pay Schemes May Undermine Positive Teacher Collaboration

Science.gov (United States)

Brewer, T. Jameson; Myers, P. S.; Zhang, Michael

2015-01-01

Educational reforms have become the new policy mainstay in educational discourse and policy. Without doubt, "fixing" teachers and increasing student test scores have both been a large component of much of the reform rhetoric. Moreover, calls for implementing merit pay schemes have uniquely combined reformer's efforts to "fix"…

The role of privacy protection in healthcare information systems adoption.

Science.gov (United States)

Hsu, Chien-Lung; Lee, Ming-Ren; Su, Chien-Hui

2013-10-01

Privacy protection is an important issue and challenge in healthcare information systems (HISs). Recently, some privacy-enhanced HISs are proposed. Users' privacy perception, intention, and attitude might affect the adoption of such systems. This paper aims to propose a privacy-enhanced HIS framework and investigate the role of privacy protection in HISs adoption. In the proposed framework, privacy protection, access control, and secure transmission modules are designed to enhance the privacy protection of a HIS. An experimental privacy-enhanced HIS is also implemented. Furthermore, we proposed a research model extending the unified theory of acceptance and use of technology by considering perceived security and information security literacy and then investigate user adoption of a privacy-enhanced HIS. The experimental results and analyses showed that user adoption of a privacy-enhanced HIS is directly affected by social influence, performance expectancy, facilitating conditions, and perceived security. Perceived security has a mediating effect between information security literacy and user adoption. This study proposes several implications for research and practice to improve designing, development, and promotion of a good healthcare information system with privacy protection.

A Simple Adaptive Overcurrent Protection of Distribution Systems With Distributed Generation

DEFF Research Database (Denmark)

Mahat, Pukar; Chen, Zhe; Bak-Jensen, Birgitte

2011-01-01

current when the system is connected to the grid and when it is islanded. This paper proposes the use of adaptive protection, using local information, to overcome the challenges of the overcurrent protection in distribution systems with distributed generation. The trip characteristics of the relays...... are updated by detecting operating states (grid connected or island) and the faulted section. The paper also proposes faulted section detection using the time over-current characteristics of the protective relays. Simulation results show that the operating state and faulted section can be correctly identified......A significant increase in the penetration of distributed generation has resulted in a possibility of operating distribution systems with distributed generation in islanded mode. However, over-current protection of an islanded distribution system is still an issue due to the difference in fault...

Agreement in polar motion measurements during the MERIT campaign

Science.gov (United States)

Djurovic, D.; Techy, C.; Paquet, P.

From the original polar motion (PM) measurements performed during the MERIT Campaign, the Chandler and the annual components are removed. The analysis of the residuals shows a high level of significant correlation between the various techniques mainly for phenomenon ranging from 30 days to a few months. For periods smaller than one month the series are not correlated except for the X component, deduced from laser and Doppler techniques, which remains significant at the 99 percent level. These results led to the belief for a new earth rotation service open to different sources of data.

Protected areas as social-ecological systems: perspectives from resilience and social-ecological systems theory.

Science.gov (United States)

Cumming, Graeme S; Allen, Craig R

2017-09-01

Conservation biology and applied ecology increasingly recognize that natural resource management is both an outcome and a driver of social, economic, and ecological dynamics. Protected areas offer a fundamental approach to conserving ecosystems, but they are also social-ecological systems whose ecological management and sustainability are heavily influenced by people. This editorial, and the papers in the invited feature that it introduces, discuss three emerging themes in social-ecological systems approaches to understanding protected areas: (1) the resilience and sustainability of protected areas, including analyses of their internal dynamics, their effectiveness, and the resilience of the landscapes within which they occur; (2) the relevance of spatial context and scale for protected areas, including such factors as geographic connectivity, context, exchanges between protected areas and their surrounding landscapes, and scale dependency in the provision of ecosystem services; and (3) efforts to reframe what protected areas are and how they both define and are defined by the relationships of people and nature. These emerging themes have the potential to transform management and policy approaches for protected areas and have important implications for conservation, in both theory and practice. © 2017 by the Ecological Society of America.

Protected areas as social-ecological systems: perspectives from resilience and social-ecological systems theory

Science.gov (United States)

Cumming, Graeme S.; Allen, Craig R.

2017-01-01

Conservation biology and applied ecology increasingly recognize that natural resource management is both an outcome and a driver of social, economic, and ecological dynamics. Protected areas offer a fundamental approach to conserving ecosystems, but they are also social-ecological systems whose ecological management and sustainability are heavily influenced by people. This editorial, and the papers in the invited feature that it introduces, discuss three emerging themes in social-ecological systems approaches to understanding protected areas: (1) the resilience and sustainability of protected areas, including analyses of their internal dynamics, their effectiveness, and the resilience of the landscapes within which they occur; (2) the relevance of spatial context and scale for protected areas, including such factors as geographic connectivity, context, exchanges between protected areas and their surrounding landscapes, and scale dependency in the provision of ecosystem services; and (3) efforts to reframe what protected areas are and how they both define and are defined by the relationships of people and nature. These emerging themes have the potential to transform management and policy approaches for protected areas and have important implications for conservation, in both theory and practice.

Kinetic Integrated Thermal Protection System (KnITPS)

Data.gov (United States)

National Aeronautics and Space Administration — Use the flexibility and shape formation possibilities inherent in knitting to form thermal protection systems that can be custom fitted to a heat shield carrier...

Significant enhancement of the thermoelectric figure of merit of polycrystalline Si films by reducing grain size

International Nuclear Information System (INIS)

Valalaki, K; Nassiopoulou, A G; Vouroutzis, N

2016-01-01

The thermoelectric properties of p-type polycrystalline silicon thin films deposited by low pressure chemical vapour deposition (LPCVD) were accurately determined at room temperature and the thermoelectric figure of merit was deduced as a function of film thickness, ranging from 100 to 500 nm. The effect of film thickness on their thermoelectric performance is discussed. More than threefold increase in the thermoelectric figure of merit of the 100 nm thick polysilicon film was observed compared to the 500 nm thick film, reaching a value as high as 0.033. This enhancement is mainly the result of the smaller grain size in the thinner films. With the decrease in grain size the resistivity of the films is increased twofold and electrical conductivity decreased, however the Seebeck coefficient is increased by 30% and the thermal conductivity is decreased eightfold, being mainly at the origin of the increased figure of merit of the 100 nm film. Our experimental results were compared to known theoretical models and the possible mechanisms involved are presented and discussed. (paper)

A new hybrid protection system for high-field superconducting magnets

CERN Document Server

Ravaioli, E; Kirby, G; ten Kate, H H J; Verweij, A P

2014-01-01

The new generation of high-field superconducting accelerator magnets poses a challenge concerning the protection of the magnet coil in the case of a quench. The very high stored energy per unit volume requires a fast and efficient quench heating system in order to avoid damage due to overheating. A new protection system for superconducting magnets is presented, comprising a combination of a novel coupling-loss induced quench (CLIQ) system and conventional quench heaters. CLIQ can provoke a very fast transition to the normal state in coil windings by introducing coupling loss and thus heat in the coil's conductor. The advantage of the hybrid protection system is a global transition, resulting in a much faster current decay, a significantly lower hot-spot temperature, and a more homogeneous temperature distribution in the magnet's coil.

System of common usage on the base of external memory devices and the SM-3 computer

International Nuclear Information System (INIS)

Baluka, G.; Vasin, A.Yu.; Ermakov, V.A.; Zhukov, G.P.; Zimin, G.N.; Namsraj, Yu.; Ostrovnoj, A.I.; Savvateev, A.S.; Salamatin, I.M.; Yanovskij, G.Ya.

1980-01-01

An easily modified system of common usage on the base of external memories and a SM-3 minicomputer replacing some pulse analysers is described. The system has merits of PA and is more advantageous with regard to effectiveness of equipment using, the possibility of changing configuration and functions, the data protection against losses due to user errors and some failures, price of one registration channel, place occupied. The system of common usage is intended for the IBR-2 pulse reactor computing centre. It is designed using the SANPO system means for SM-3 computer [ru

Flight envelope protection system for unmanned aerial vehicles

KAUST Repository

Claudel, Christian G.; Shaqura, Mohammad

2016-01-01

Systems and methods to protect the flight envelope in both manual flight and flight by a commercial autopilot are provided. A system can comprise: an inertial measurement unit (IMU); a computing device in data communication with the IMU

PG BN 1600 sodium fire protection system

International Nuclear Information System (INIS)

Bar, J.; Urbancik, L.

1978-12-01

A design was developed of a fire protection system for steam generator of a 1600 MW sodium cooled fast reactor (BN-1600). Chemical reactions are described of liquid sodium with atmospheric components and solid materials coming into contact with sodium in its release from the steam generator, and in safeguarding protection against sodium fires. The requirements for the purity of nitrogen as an atmosphere inert to liquid sodium are given. Characteristics and basic parameters are shown of level and spray fires, elementary terms are explained concerning the properties of aerosols formed during fires, the methods and means of release signalling and fire alarm are described as are fire precautions using fire-fighting equipment, modifying the support tank and the cell bottom and building sewage pits. The design of the system comprises an alarm system for liquid sodium using point and line electric contact sensors and flame photometer based aerosol sensors as well as a fire-fighting system based on the system of channelling liquid sodium into emergency discharge tanks filled with an inert gas, a set of fire extinguishers and other fire fighting material, and measures for the elimination of sodium fire consequences. (J.B.)

Fault-tolerant reactor protection system

International Nuclear Information System (INIS)

Gaubatz, D.C.

1997-01-01

A reactor protection system is disclosed having four divisions, with quad redundant sensors for each scram parameter providing input to four independent microprocessor-based electronic chassis. Each electronic chassis acquires the scram parameter data from its own sensor, digitizes the information, and then transmits the sensor reading to the other three electronic chassis via optical fibers. To increase system availability and reduce false scrams, the reactor protection system employs two levels of voting on a need for reactor scram. The electronic chassis perform software divisional data processing, vote 2/3 with spare based upon information from all four sensors, and send the divisional scram signals to the hardware logic panel, which performs a 2/4 division vote on whether or not to initiate a reactor scram. Each chassis makes a divisional scram decision based on data from all sensors. Each division performs independently of the others (asynchronous operation). All communications between the divisions are asynchronous. Each chassis substitutes its own spare sensor reading in the 2/3 vote if a sensor reading from one of the other chassis is faulty or missing. Therefore the presence of at least two valid sensor readings in excess of a set point is required before terminating the output to the hardware logic of a scram inhibition signal even when one of the four sensors is faulty or when one of the divisions is out of service. 16 figs

Relative merits of size, field, and current on ignited tokamak performance

International Nuclear Information System (INIS)

Uckan, N.A.

1988-01-01

A simple global analysis is developed to examine the relative merits of size (L = a or R/sub 0 /), field (B/sub 0 /), and current (I) on ignition regimes of tokamaks under various confinement scaling laws. Scalings of key parameters with L, B/sub 0 /, and I are presented at several operating points, including (a) optimal path to ignition (saddle point), (b) ignition at minimum beta, (c) ignition at 10 keV, and (d) maximum performance at the limits of density and beta. Expressions for the saddle point and the minimum conditions needed for ohmic ignition are derived analytically for any confinement model of the form tau/sub E/ ∼ n/sup x/T/sup y/. For a wide range of confinement models, the ''figure of merit'' parameters and I are found to give a good indication of the relative performance of the devices where q* is the cylindrical safety factor. As an illustration, the results are applied to representative ''CIT'' (as a class of compact, high-field ignition tokamaks) and ''Super-JETs'' [a class of large-size (few x JET), low-field, high-current (≥20-MA) devices.

How Money Helps Keep Students in College: The Relationship between Family Finances, Merit-Based Aid, and Retention in Higher Education

Science.gov (United States)

Olbrecht, Alexandre M.; Romano, Christopher; Teigen, Jeremy

2016-01-01

In this paper, we leverage detailed, individual-level student data to understand the relationships between family finances, merit-based aid, and first-year student retention. With three cohorts of student data that comprise family financial status, institutional merit scholarships, and many of the other known correlates of student retention, we…

Overvoltage protection for magnetic system during disruption in tokamak

International Nuclear Information System (INIS)

Zhang, Ming; Li, Xiaolong; He, Yang; Zhang, Jun; Chen, Zhongyong; Yu, Kexun

2015-01-01

Highlights: • We investigate the way to limit the plasma disruption overvoltage by using the MOVs. • An overvoltage model of plasma disruption is introduced. • The overvoltage protection scheme has been verified by disruption experiments. • The overvoltage during plasma disruption can be limited to 330 V. - Abstract: During a plasma disruption the magnetic flux in the tokamak changes rapidly, which in most cases will cause high-voltage surges among the magnetic systems and may bring severe damage to the components if there is no overvoltage protection. This paper investigates the way to limit the plasma disruption overvoltage and absorb the energy with the use of metal oxide varistors (MOVs). An overvoltage model of plasma disruption is introduced which can be used for the simulation of plasma disruption and the analysis of the overvoltage. The effectiveness of the overvoltage protection system is validated with disruption experiments. It shows that by optimizing the varistors voltage, the overvoltage during plasma disruption can be limited to an ideal low value. Now the overvoltage protection system has been deployed in J-TEXT tokamak and serves well for daily experiments.

Relay Protection and Automation Systems Based on Programmable Logic Integrated Circuits

International Nuclear Information System (INIS)

Lashin, A. V.; Kozyrev, A. V.

2015-01-01

One of the most promising forms of developing the apparatus part of relay protection and automation devices is considered. The advantages of choosing programmable logic integrated circuits to obtain adaptive technological algorithms in power system protection and control systems are pointed out. The technical difficulties in the problems which today stand in the way of using relay protection and automation systems are indicated and a new technology for solving these problems is presented. Particular attention is devoted to the possibility of reconfiguring the logic of these devices, using programmable logic integrated circuits

Advanced digital instrumentation and control system for nuclear power plant protection

International Nuclear Information System (INIS)

Sabino, D.

1997-01-01

The Diverse Protection System (DPS) is described. The DPS is a state-of-the-art digital protection system developed as a back-up to the primary reactor protection system at the Temelin nuclear power plant, featuring a compact hardware design based on VMEbus technology. This technology allows for ease in adding or modifying the number and type of input modules and processors. The DPS software is written in a high level language suitable for safety critical applications. The software is both modular and configurable allowing for potential future modifications and software reuse

Nuclear Detection Figure Of Merit (NDFOM) Version 1.2 User's Guide

International Nuclear Information System (INIS)

Stroud, Phillip D.; Dufresne, Thomas A.

2012-01-01

NDFOM is a detector database and detector evaluation system, accessible as a web service. It runs on the same server as the Patriot service, but uses port 8081. In this user's guide, we will use the example case that the patriot service is running on http://patriot.lanl.gov. Then the NDFOM service would be accessible at the URL http://patriot.lanl.gov:8081/ndfom. In addition to local server installations, common server locations are 1) a patriot server running on a virtual machine (use the virtual machine URL with :8081/ndfom), and 2) a patriot server running on a local machine (use http://localhost:8081/ndfom or http://127.0.0.1:8081/ndfom). The home screen provides panels to select detectors, a scenario, and a figure-of-merit. It also has an 'analyze' button, which will evaluate the selected figure-of-merit for the selected detectors, for the scenario selected by the user. The detector effectiveness evaluations are presented through the browser in a ranked list of detectors. The user does not need to log in to perform analysis with pre-supplied detectors, scenarios, and FOMs. The homepage view is shown in Figure 1. The first panel displays a list of the detectors in the current detector database. The user can select one, some, or all detectors to evaluate. On the right of each listed detector, there is a star icon. Clicking that icon will open a panel that displays the details about that detector, such as detector material, dimensions, thresholds, etc. The center panel displays the pre-supplied scenarios that are in the database. A scenario specifies the source of interest, the spectrum of the radiation, the background radiation spectrum, the distance or distance of closest approach, the allowable false positive rate, and the dwell time or speed. Scenario details can be obtained by clicking the star to the right of a scenario. A scenario can be selected by clicking it.

Information support systems for cultural heritage protection against flooding

Directory of Open Access Journals (Sweden)

K. Nedvedova

2015-08-01

Full Text Available The goal of this paper is to present use of different kind of software applications to create complex support system for protection of cultural heritage against flooding. The project is very complex and it tries to cover the whole area of the problem from prevention to liquidation of aftermath effects. We used GIS for mapping the risk areas, ontology systems for vulnerability assessment application and the BORM method (Business Object Relation Modelling for flood protection system planning guide. Those modern technologies helped us to gather a lot of information in one place and provide the knowledge to the broad audience.

Political problems in the system of radiation protection laws of Japan

International Nuclear Information System (INIS)