WorldWideScience

Sample records for mercury bromides

  1. Enhancement of mercury capture by the simultaneous addition of hydrogen bromide (HBr) and fly ashes in a slipstream facility.

    Science.gov (United States)

    Cao, Yan; Wang, Quan-Hai; Li, Jun; Cheng, Jen-Chieh; Chan, Chia-Chun; Cohron, Marten; Pan, Wei-Ping

    2009-04-15

    Low halogen content in tested Powder River Basin (PRB) coals and low loss of ignition content (LOI) in PRB-derived fly ash were likely responsible for higher elemental mercury content (averaging about 75%) in the flue gas and also lower mercury capture efficiency by electrostatic precipitator (ESP) and wet-FGD. To develop a cost-effective approach to mercury capture in a full-scale coal-fired utility boiler burning PRB coal, experiments were conducted adding hydrogen bromide (HBr) or simultaneously adding HBr and selected fly ashes in a slipstream reactor (0.152 x 0.152 m) under real flue gas conditions. The residence time of the flue gas inside the reactorwas about 1.4 s. The average temperature of the slipstream reactor was controlled at about 155 degrees C. Tests were organized into two phases. In Phase 1, only HBr was added to the slipstream reactor, and in Phase 2, HBr and selected fly ash were added simultaneously. HBr injection was effective (>90%) for mercury oxidation at a low temperature (155 degrees C) with an HBr addition concentration of about 4 ppm in the flue gas. Additionally, injected HBr enhanced mercury capture by PRB fly ash in the low-temperature range. The mercury capture efficiency, attesting conditions of the slipstream reactor, reached about 50% at an HBr injection concentration of 4 ppm in the flue gas. Compared to only the addition of HBr, simultaneously adding bituminous-derived fly ash in a minimum amount (30 lb/MMacf), together with HBr injection at 4 ppm, could increase mercury capture efficiency by 30%. Injection of lignite-derived fly ash at 30 lb/MMacf could achieve even higher mercury removal efficiency (an additional 35% mercury capture efficiency compared to HBr addition alone).

  2. Full scale calcium bromide injection with subsequent mercury oxidation and removal within wet flue gas desulphurization system: Experience at a 700 MW coal-fired power facility

    Science.gov (United States)

    Berry, Mark Simpson

    The Environmental Protection Agency promulgated the Mercury and Air Toxics Standards rule, which requires that existing power plants reduce mercury emissions to meet an emission rate of 1.2 lb/TBtu on a 30-day rolling average and that new plants meet a 0.0002 lb/GWHr emission rate. This translates to mercury removals greater than 90% for existing units and greater than 99% for new units. Current state-of-the-art technology for the control of mercury emissions uses activated carbon injected upstream of a fabric filter, a costly proposition. For example, a fabric filter, if not already available, would require a 200M capital investment for a 700 MW size unit. A lower-cost option involves the injection of activated carbon into an existing cold-side electrostatic precipitator. Both options would incur the cost of activated carbon, upwards of 3M per year. The combination of selective catalytic reduction (SCR) reactors and wet flue gas desulphurization (wet FGD) systems have demonstrated the ability to substantially reduce mercury emissions, especially at units that burn coals containing sufficient halogens. Halogens are necessary for transforming elemental mercury to oxidized mercury, which is water-soluble. Plants burning halogen-deficient coals such as Power River Basin (PRB) coals currently have no alternative but to install activated carbon-based approaches to control mercury emissions. This research consisted of investigating calcium bromide addition onto PRB coal as a method of increasing flue gas halogen concentration. The treated coal was combusted in a 700 MW boiler and the subsequent treated flue gas was introduced into a wet FGD. Short-term parametric and an 83-day longer-term tests were completed to determine the ability of calcium bromine to oxidize mercury and to study the removal of the mercury in a wet FGD. The research goal was to show that calcium bromine addition to PRB coal was a viable approach for meeting the Mercury and Air Toxics Standards rule

  3. Mercury

    International Nuclear Information System (INIS)

    Vilas, F.; Chapman, C.R.; Matthews, M.S.

    1988-01-01

    Papers are presented on future observations of and missions to Mercury, the photometry and polarimetry of Mercury, the surface composition of Mercury from reflectance spectrophotometry, the Goldstone radar observations of Mercury, the radar observations of Mercury, the stratigraphy and geologic history of Mercury, the geomorphology of impact craters on Mercury, and the cratering record on Mercury and the origin of impacting objects. Consideration is also given to the tectonics of Mercury, the tectonic history of Mercury, Mercury's thermal history and the generation of its magnetic field, the rotational dynamics of Mercury and the state of its core, Mercury's magnetic field and interior, the magnetosphere of Mercury, and the Mercury atmosphere. Other papers are on the present bounds on the bulk composition of Mercury and the implications for planetary formation processes, the building stones of the planets, the origin and composition of Mercury, the formation of Mercury from planetesimals, and theoretical considerations on the strange density of Mercury

  4. Mercury

    NARCIS (Netherlands)

    de Vries, Irma

    2017-01-01

    Mercury is a naturally occurring metal that exists in several physical and chemical forms. Inorganic mercury refers to compounds formed after the combining of mercury with elements such as chlorine, sulfur, or oxygen. After combining with carbon by covalent linkage, the compounds formed are called

  5. Mercury

    Science.gov (United States)

    ... build up in fish, shellfish, and animals that eat fish. The nervous system is sensitive to all forms of mercury. Exposure to high levels can damage the brain and kidneys. Pregnant women can pass the mercury in their bodies to their babies. It is important to protect your family from ...

  6. Mercury

    Science.gov (United States)

    ... has set a limit of 2 parts of mercury per billion parts of drinking water (2 ppb). The Food and Drug Administration (FDA) has set a maximum permissible level of 1 part of methylmercury in a million ... of 0.1 milligram of organic mercury per cubic meter of workplace air (0.1 ...

  7. Mercury

    CERN Document Server

    Balogh, André; Steiger, Rudolf

    2008-01-01

    Mercury, the planet closest to the Sun, is different in several respects from the other three terrestrial planets. In appearance, it resembles the heavily cratered surface of the Moon, but its density is high, it has a magnetic field and magnetosphere, but no atmosphere or ionosphere. This book reviews the progress made in Mercury studies since the flybys by Mariner 10 in 1974-75, based on the continued research using the Mariner 10 archive, on observations from Earth, and on increasingly realistic models of its interior evolution.

  8. Method for scavenging mercury

    Science.gov (United States)

    Chang, Shih-ger [El Cerrito, CA; Liu, Shou-heng [Kaohsiung, TW; Liu, Zhao-rong [Beijing, CN; Yan, Naiqiang [Berkeley, CA

    2009-01-20

    Disclosed herein is a method for removing mercury from a gas stream comprising contacting the gas stream with a getter composition comprising bromine, bromochloride, sulphur bromide, sulphur dichloride or sulphur monochloride and mixtures thereof. In one preferred embodiment the getter composition is adsorbed onto a sorbent. The sorbent may be selected from the group consisting of flyash, limestone, lime, calcium sulphate, calcium sulfite, activated carbon, charcoal, silicate, alumina and mixtures thereof. Preferred is flyash, activated carbon and silica.

  9. Methylnaltrexone bromide methanol monosolvate

    Directory of Open Access Journals (Sweden)

    Xinbo Zhou

    2012-03-01

    Full Text Available In the title compound [systematic name: (4R,4aS,7aR,12bS-3-cyclopropylmethyl-4a,9-hydroxy-7-oxo-2,3,4,4a,5,6,7,7a-octahydro-1H-4,12-methanobenzofuro[3,2-e]isoquinolin-3-ium bromide methanol monosolvate], C21H26NO4+·Br−·CH3OH, two of the three six-membered rings adopt chair conformations while the third, which contains a C=C double bond, adopts an approximate half-boat conformation. The 2,3-dihydrofuran ring adopts an envelope conformation. In the crystal, the components are linked by O—H...O and O—H...Br hydrogen bonds. The absolute stereochemistry was inferred from one of the starting materials.

  10. Power Plant Bromide Discharges and Downstream Drinking Water Systems in Pennsylvania.

    Science.gov (United States)

    Good, Kelly D; VanBriesen, Jeanne M

    2017-10-17

    Coal-fired power plants equipped with wet flue gas desulfurization (FGD) systems have been implicated in increasing bromide levels and subsequent increases in disinfection byproducts at downstream drinking water plants. Bromide was not included as a regulated constituent in the recent steam electric effluent limitations guidelines and standards (ELGs) since the U.S. EPA analysis suggested few drinking water facilities would be affected by bromide discharges from power plants. The present analysis uses a watershed approach to identify Pennsylvania drinking water intakes downstream of wet FGD discharges and to assess the potential for bromide discharge effects. Twenty-two (22) public drinking water systems serving 2.5 million people were identified as being downstream of at least one wet FGD discharge. During mean August conditions (generally low-flow, minimal dilution) in receiving rivers, the median predicted bromide concentrations contributed by wet FGD at Pennsylvania intake locations ranged from 5.2 to 62 μg/L for the Base scenario (including only natural bromide in coal) and from 16 to 190 μg/L for the Bromide Addition scenario (natural plus added bromide for mercury control); ranges depend on bromide loads and receiving stream dilution capacity.

  11. Bromide in some coastal and oceanic waters of India

    Digital Repository Service at National Institute of Oceanography (India)

    DeSouza, F.P.; Dalal, V.N.K.

    Bromide concentration and bromide/chlorinity ratio are estimated in coastal waters of Goa, Minicoy Lagoon, Western Arabian Sea and Western Bay of Bengal. The influence of precipitation and river runoff on bromide and bromide/chlorinity ratio...

  12. Mercury and Your Health

    Science.gov (United States)

    ... the Risk of Exposure to Mercury Learn About Mercury What is Mercury What is Metallic mercury? Toxicological Profile ToxFAQs Mercury Resources CDC’s National Biomonitoring Program Factsheet on Mercury ...

  13. Mercury removal sorbents

    Science.gov (United States)

    Alptekin, Gokhan

    2016-03-29

    Sorbents and methods of using them for removing mercury from flue gases over a wide range of temperatures are disclosed. Sorbent materials of this invention comprise oxy- or hydroxyl-halogen (chlorides and bromides) of manganese, copper and calcium as the active phase for Hg.sup.0 oxidation, and are dispersed on a high surface porous supports. In addition to the powder activated carbons (PACs), this support material can be comprised of commercial ceramic supports such as silica (SiO.sub.2), alumina (Al.sub.2O.sub.3), zeolites and clays. The support material may also comprise of oxides of various metals such as iron, manganese, and calcium. The non-carbon sorbents of the invention can be easily injected into the flue gas and recovered in the Particulate Control Device (PCD) along with the fly ash without altering the properties of the by-product fly ash enabling its use as a cement additive. Sorbent materials of this invention effectively remove both elemental and oxidized forms of mercury from flue gases and can be used at elevated temperatures. The sorbent combines an oxidation catalyst and a sorbent in the same particle to both oxidize the mercury and then immobilize it.

  14. Got Mercury?

    Science.gov (United States)

    Meyers, Valerie E.; McCoy, J. Torin; Garcia, Hector D.; James, John T.

    2009-01-01

    Many of the operational and payload lighting units used in various spacecraft contain elemental mercury. If these devices were damaged on-orbit, elemental mercury could be released into the cabin. Although there are plans to replace operational units with alternate light sources, such as LEDs, that do not contain mercury, mercury-containing lamps efficiently produce high quality illumination and may never be completely replaced on orbit. Therefore, exposure to elemental mercury during spaceflight will remain possible and represents a toxicological hazard. Elemental mercury is a liquid metal that vaporizes slowly at room temperature. However, it may be completely vaporized at the elevated operating temperatures of lamps. Although liquid mercury is not readily absorbed through the skin or digestive tract, mercury vapors are efficiently absorbed through the respiratory tract. Therefore, the amount of mercury in the vapor form must be estimated. For mercury releases from lamps that are not being operated, we utilized a study conducted by the New Jersey Department of Environmental Quality to calculate the amount of mercury vapor expected to form over a 2-week period. For longer missions and for mercury releases occurring when lamps are operating, we conservatively assumed complete volatilization of the available mercury. Because current spacecraft environmental control systems are unable to remove mercury vapors, both short-term and long-term exposures to mercury vapors are possible. Acute exposure to high concentrations of mercury vapors can cause irritation of the respiratory tract and behavioral symptoms, such as irritability and hyperactivity. Chronic exposure can result in damage to the nervous system (tremors, memory loss, insomnia, etc.) and kidneys (proteinurea). Therefore, the JSC Toxicology Group recommends that stringent safety controls and verifications (vibrational testing, etc.) be applied to any hardware that contains elemental mercury that could yield

  15. Basic Information about Mercury

    Science.gov (United States)

    ... Your Environment Contact Us Share Basic Information about Mercury On this page: What is mercury? Emissions of ... Consumer products that traditionally contain mercury What is Mercury? Mercury is a naturally-occurring chemical element found ...

  16. Tiotropium bromide inhibits human monocyte chemotaxis

    Directory of Open Access Journals (Sweden)

    Kurai M

    2012-08-01

    Full Text Available Tiotropium bromide (Spiriva® is used as a bronchodilator in chronic obstructive pulmonary disease (COPD. However, clinical evidence suggests that tiotropium bromide may improve COPD by mechanisms beyond bronchodilation. We hypothesized that tiotropium bromide may act as an anti-inflammatory agent by inhibiting monocyte chemotaxis, a process that plays an important role in the lung inflammation of COPD. To test this hypothesis monocytes were pretreated with tiotropium bromide prior to exposure to chemotactic agents and monocyte chemotactic activity (MCA was evaluated with a blind chamber technique. Tiotropium bromide inhibited MCA in a dose- and time- dependent manner (respectively, p< 0.01 by directly acting on the monocyte. Acetylcholine (ACh challenge increased MCA (p< 0.01, and tiotropium bromide effectively reduced (p< 0.01 the increase in MCA by ACh. The inhibition of MCA by tiotropium bromide was reversed by a muscarinic type 3 (M3-muscarinic receptor antagonist (p< 0.01, and was not effected by an M2 receptor antagonist. Furthermore, a selective M3 receptor agonist, cevimeline, and Gq protein stimulator, Pasteurella multocida toxin, significantly increased MCA (P < 0.01, and tiotropium bromide pretreatment reduced (p< 0.01 the increase in MCA induced by these agents. These results suggest that tiotropium might regulate monocyte chemotaxis, in part, by interfering with M3-muscarinic receptor coupled Gq protein signal transduction. These results provide new insight that an anti-cholinergic therapeutic may provide anti-inflammatory action in the pulmonary system.

  17. 49 CFR 173.193 - Bromoacetone, methyl bromide, chloropicrin and methyl bromide or methyl chloride mixtures, etc.

    Science.gov (United States)

    2010-10-01

    ... methyl bromide or methyl chloride mixtures, etc. 173.193 Section 173.193 Transportation Other Regulations... bromide, chloropicrin and methyl bromide or methyl chloride mixtures, etc. (a) Bromoacetone must be...) Bromoacetone, methyl bromide, chloropicrin and methyl bromide mixtures, chloropicrin and methyl chloride...

  18. Mercury and Pregnancy

    Science.gov (United States)

    ... Home > Pregnancy > Is it safe? > Mercury and pregnancy Mercury and pregnancy E-mail to a friend Please ... vision problems. How can you be exposed to mercury? Mercury has several forms: It can be a ...

  19. Gas phase radiation chemistry of ethyl bromide

    International Nuclear Information System (INIS)

    Frank, A.J.; Hanrahan, R.J.

    1976-01-01

    The γ radiolysis of ethyl bromide has been investigated at 100 Torr pressure and 23 0 C. In the pure system between an absorbed dose of 1.0 x 10 20 and 1.5 x 10 20 eV/g the major products and their respective G values are as follows: hydrogen bromide, 3.89; ethane, 2.70; ethylene, 2.17; acetylene, 0.31; hydrogen, 1.39; 1,1-dibromoethane, 0.88; 1,2-dibromoethane, 0.12; vinyl bromide, 0.32; methane, 0.083; methyl bromide, 0.080; and bromoform, 0.0078. When oxygen is added, the G values in this dose range become the following: hydrogen bromide, 4.89; ethane, 0.31; ethylene, 0.78; acetylene, 0.27; hydrogen, 1.38; 1,1-dibromoethane, 0.028; 1,2-dibromoethane, 0.56; vinyl bromide, 0.0; methane 0.03; methyl bromide, 0.32; and bromoform, 0.0034. Bromine is also formed with a G value of 2.4 when oxygen is added. The presence of hydrogen and acetylene in the radiolysis indicates that these species must be formed from higher energy processes not accessible in the 253.7-nm photolysis, which was studied in a parallel investigation. The product distribution indicates that the probabilities of single bond rupture in the primary event are approximately C 2 H 5 --Br:C 2 H 4 Br--H:CH 3 --CH 2 Br = 1.00:0.40:0.06. Either a hot hydrogen atom abstraction reaction or direct molecular H 2 elimination accounts for about 16 percent of the hydrogen yield. Strong similarities in dose-yield plots suggest that many of the secondary processes involved in the photolysis are important in the radiolysis of ethyl bromide as well. The high pressure mass spectrometry of the system indicates the role of ionic species. Differences in radiolytic behavior of ethyl chloride, bromide, and iodide can largely be explained in terms of the energetics of the primary and secondary processes in each system

  20. Mutagenic effects of lead (II) bromide.

    Science.gov (United States)

    Maslat, A O; Haas, H J

    1989-12-01

    The mutagenicity of lead (II) bromide (a combustion product of the gasoline additives lead (IV) tetraethyl and 1,2-dibromoethane) was investigated using various strains of bacteria. Taking prodigiosin (the red pigment) production as a marker, lead (II) bromide was found to be mutagenic in S. marcescens, leading to the appearance of white mutant colonies that are unable to produce such a pigment. This compound was also found to be mutagenic in E. coli KMBL1851, resulting in the appearance of rifampicin-resistant mutants in addition to Met+ and His+ revertants. Some of the S. marcescens mutants were found to be reversible, able to resynthesize prodigiosin. Differences in the sensitivity to antibiotics as well as in the biochemical properties were detected between the mutants and their corresponding wild types. Lead (II) bromide gave positive results in the Ames test performed with strain TA 1535.

  1. Modeling and analysis of calcium bromide hydrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Lottes, Steven A.; Lyczkowski, Robert W.; Panchal, Chandrakant B.; Doctor, Richard D. [Energy Systems Division, Argonne National Laboratory, 9700 S. Cass Avenue, Argonne, IL 60439 (United States)

    2009-05-15

    The main focus of this paper is the modeling, simulation, and analysis of the calcium bromide hydrolysis reactor stage in the calcium-bromine thermochemical water-splitting cycle for nuclear hydrogen production. One reactor concept is to use a spray of calcium bromide into steam, in which the heat of fusion supplies the heat of reaction. Droplet models were built up in a series of steps incorporating various physical phenomena, including droplet flow, heat transfer, phase change, and reaction, separately. Given the large heat reservoir contained in a pool of molten calcium bromide that allows bubbles to rise easily, using a bubble column reactor for the hydrolysis appears to be a feasible and promising alternative to the spray reactor concept. The two limiting cases of bubble geometry, spherical and spherical-cap, are considered in the modeling. Results for both droplet and bubble modeling with COMSOL MULTIPHYSICS trademark are presented, with recommendations for the path forward. (author)

  2. Methyl bromide residues in fumigated cocoa beans with particular reference to inorganic bromide

    International Nuclear Information System (INIS)

    Adomako, D.

    1976-01-01

    Inorganic bromide residues and 14 C-labelled methylated products (expressed as CH 3 Br equivalent) in cocoa beans fumigated with [ 14 C]-methyl bromide have been determined by radiometric and chemical methods. Determination of 14 C by direct combustion in an oxygen chamber followed by liquid scintillation counting confirmed previous findings with respect to the magnitude, distribution and chemical nature of the residues. Although recovery of added bromide was good, the values of total bromide obtained by the chemical method were only half of those estimated from the total residual 14 C-activity. This is attributed to loss of organic (presumably, protein-bound) bromide. In agreement with the total 14 C-labelled residue contents, total bromide in shells was 20 times greater than that in nibs. The low levels of residues in the nib (12ppm as CH 3 Br equivalent, 10ppm Br) and the further reduction of organic residues by roasting suggest that no toxicological and nutritional hazards may be expected from fumigation of cocoa beans with methyl bromide. (author)

  3. nanoparticles modified by either cetyltrimethylammonium bromide or ...

    African Journals Online (AJOL)

    Comparative assessment of poly (D,L-lactide-co-glycolide) nanoparticles modified by either cetyltrimethylammonium bromide or chitosan for plasmid DNA ... The PDF file you selected should load here if your Web browser has a PDF reader plug-in installed (for example, a recent version of Adobe Acrobat Reader).

  4. Mercury's Messenger

    Science.gov (United States)

    Chapman, Clark R.

    2004-01-01

    Forty years after Mariner 2, planetary exploration has still only just begun, and many more missions are on drawing boards, nearing the launch pad, or even en route across interplanetary space to their targets. One of the most challenging missions that will be conducted this decade is sending the MESSENGER spacecraft to orbit the planet Mercury.…

  5. Mercury Report-Children's exposure to elemental mercury

    Science.gov (United States)

    ... gov . Mercury Background Mercury Report Additional Resources Mercury Report - Children's Exposure to Elemental Mercury Recommend on Facebook ... I limit exposure to mercury? Why was the report written? Children attending a daycare in New Jersey ...

  6. 77 FR 20752 - Methyl Bromide; Proposed Pesticide Tolerance

    Science.gov (United States)

    2012-04-06

    ... Classification System (NAICS) codes have been provided to assist you and others in determining whether this...- efficient values than methyl bromide. And, although methyl bromide tends to be lipid soluble, the low...

  7. Methyl bromide residues in fumigated cocoa beans

    International Nuclear Information System (INIS)

    Adomako, D.

    1975-01-01

    The 14 C activity in unroasted [ 14 C]-methyl bromide fumigated cocoa beans was used to study the fate and persistence of CH 3 Br in the stored beans. About 70% of the residues occurred in the shells. Unchanged CH 3 Br could not be detected, all the sorbed CH 3 Br having reacted with bean constituents apparently to form 14 C-methylated derivatives and inorganic bromide. No 14 C activity was found in the lipid fraction. Roasting decreased the bound (non-volatile) residues, with corresponding changes in the activities and amounts of free sugars, free and protein amino acids. Roasted nibs and shells showed a two-fold increase in the volatile fraction of the 14 C residue. This fraction may be related to the volatile aroma compounds formed by Maillard-type reactions. (author)

  8. [Propantheline bromide is effective against dog drooling].

    Science.gov (United States)

    Gyldenløve, Mette; Thyssen, Jacob P

    2015-12-21

    Hyperhidrosis is a common condition characterized by extensive sweat secretion. Systemic treatment with anticholinergics might prove effective, but patients often suffer from side effects, e.g. dryness of the mouth. We present a clinical case of severe polydipsia in a six-month-old puppy who had accidentally consumed 50 tablets of propantheline bromide 15 mg. Afterwards the puppy suffered from severe polydipsia, which cleared without treatment after three days.

  9. Environmental mercury problem

    Energy Technology Data Exchange (ETDEWEB)

    D' Itri, F.M.

    1972-01-01

    The urgent need to eliminate or greatly reduce the discharge of mercury into the environment is paramount to the health and well being of man. That all forms of mercury are hazardous is widely recognized, but what is more devastating to our society is that all forms of mercury appear to have the potential to be converted in to highly toxic monomethylmercury, or dimethylmercury. This paper examined the historical uses of mercury, the background concentrations of mercury, the analytical methods for the determination of mercury, the contamination of the food chain by mercury, the biological methylation of mercury, the decontamination and restoration of mercury polluted areas, the epidemiology and toxicology of mercury, and the chronology of the world's mercury poisoning problem.

  10. Mercury contamination extraction

    Science.gov (United States)

    Fuhrmann, Mark [Silver Spring, MD; Heiser, John [Bayport, NY; Kalb, Paul [Wading River, NY

    2009-09-15

    Mercury is removed from contaminated waste by firstly applying a sulfur reagent to the waste. Mercury in the waste is then permitted to migrate to the reagent and is stabilized in a mercury sulfide compound. The stable compound may then be removed from the waste which itself remains in situ following mercury removal therefrom.

  11. Aclidinium bromide for the treatment of chronic obstructive pulmonary disease.

    Science.gov (United States)

    Stone, Lowell E; Skelley, Jessica W; Kyle, Jeffrey A; Elmore, Lindsey K

    2014-03-01

    The safety and efficacy of the second U.S.-approved long-acting inhaled anticholinergic for controlling bronchospasm in patients with chronic obstructive pulmonary disease (COPD) are reviewed. Aclidinium bromide (Tudorza, Forest Pharmaceuticals) is indicated for long-term maintenance therapy for COPD-associated bronchospasm. It is marketed as a 60-dose metered-dose inhaler to be used twice daily. In Phase II and III clinical trials involving a total of more than 3000 patients, daily use of aclidinium bromide was found to significantly improve selected key indicators of lung function (trough values for forced expiratory volume at one second [FEV1] and other FEV1 outcome measures) compared with placebo use. Other benefits of aclidinium bromide therapy, including a significant reduction in nighttime COPD symptoms, were demonstrated for up to one year. However, aclidinium bromide has not been consistently demonstrated to be more effective than the other currently available long-acting inhaled anticholinergic, tiotropium bromide. Furthermore, the clinical trials indicated no significant difference between aclidinium bromide and tiotropium bromide with regard to rates of systemic adverse effects. For some patients, aclidinium bromide may offer advantages over tiotropium bromide (e.g., a faster time to peak FEV1, lower cost of therapy). Aclidinium bromide is an inhaled anticholinergic that improves lung function measures in patients with COPD. The most common adverse effects during clinical trials of the drug were headache, nasopharyngitis, and cough, none of which occurred at significantly higher rates than were seen with placebo use.

  12. Mercury Quick Facts: Health Effects of Mercury Exposure

    Science.gov (United States)

    Mercury Quick Facts Health Effects of Mercury Exposure What is Elemental Mercury? Elemental (metallic) mercury is the shiny, silver-gray metal found in thermometers, barometers, and thermostats and other ...

  13. Studies on chlorinated bromide salt for microfouling control

    International Nuclear Information System (INIS)

    Satpathy, K.K.; Rajmohan, R.; Rao, T.S.; Nair, K.V.K.; Mathur, P.K.

    1995-01-01

    The Fast Breeder Test reactor (FBTR) at Kalpakkam has been facing various problems in cooling water systems in spite of intermittent chlorination.Effects of chlorinated-bromide mixture was evaluated against heterotrophic bacteria (TVC) and iron oxidising bacteria (IOB) vis-a-vis chlorine. Results indicated that chlorinated-bromide mixture was far superior (2 orders of magnitude for TVC and 2 times for IOB) to chlorine in microfouling control. Results also showed that at bromide to chlorine ratio of one effectiveness of chlorinated-bromide was at its maximum. (author). 9 refs., 1 tab

  14. Hydrogen-bond interactions in morpholinium bromide

    Directory of Open Access Journals (Sweden)

    Alvaro S. de Sousa

    2011-10-01

    Full Text Available In the title compound, C4H10NO+·Br−, which was synthesized by dehydration of diethanolamine with HBr, morpholinium and bromide ions are linked into chains by N—H...Br hydrogen bonds describing a C21(4 graph-set motif. Weaker bifurcated N—H...Br interactions join centrosymmetrically related chains through alternating binary graph-set R42(8 and R22(4 motifs, to form ladders along [100]. In addition, C—H...O interactions between centrosymmetric morpholinium cations link ladders, via R^2_2(8 motifs, to yield sheets parallel to (101, which in turn are crosslinked by weak C—H...O interactions, related across a glide plane, to form a three-dimensional network.

  15. Single ion dynamics in molten sodium bromide

    Energy Technology Data Exchange (ETDEWEB)

    Alcaraz, O.; Trullas, J. [Departament de Física i Enginyeria Nuclear, Universitat Politècnica de Catalunya, 08034 Barcelona (Spain); Demmel, F. [ISIS Facility, Rutherford Appleton Laboratory, Didcot OX11 0QX (United Kingdom)

    2014-12-28

    We present a study on the single ion dynamics in the molten alkali halide NaBr. Quasielastic neutron scattering was employed to extract the self-diffusion coefficient of the sodium ions at three temperatures. Molecular dynamics simulations using rigid and polarizable ion models have been performed in parallel to extract the sodium and bromide single dynamics and ionic conductivities. Two methods have been employed to derive the ion diffusion, calculating the mean squared displacements and the velocity autocorrelation functions, as well as analysing the increase of the line widths of the self-dynamic structure factors. The sodium diffusion coefficients show a remarkable good agreement between experiment and simulation utilising the polarisable potential.

  16. Perfluorooctyl bromide emulsion contrast agent for tumors

    International Nuclear Information System (INIS)

    Tsuda, Yoshio; Ueda, Yasuo; Tanaka, Mikio; Yamanouchi, Kouichi; Yokoyama, Kazumasa

    1985-01-01

    Perfluorooctyl bromide (PFOB), a biologically inert radiodense compound, was evaluated as a potential contrast agent for tumors. When 25 w/v% PFOB emulsion was administered intravenously in rats with AH 130 tumor, the tumor became radiopaque using conventional X-rays. Rabbits were implanted into liver with VX 2 carcinoma and were given 10 ml/kg PFOB emulsion intravenously. Computed tomographic scanning of the rabbits showed the dense enhancement of the rim of the tumor. The PFOB contents in the tumor, the tumor-rim and the normal liver tissues were determined by gas chromatography. The differences of PFOB contents in three different locations showed the density of the tumor rim was due to the accumulation of PFOB in the periphery of the tumor. Optical and electron microscopy revealed lots of vaculoes of PFOB particles in macrophages around the tumor. Thus, PFOB emulsion may be useful in detection of tumors. (author)

  17. Potassium bromide, KBr/ ε: New Force Field

    Science.gov (United States)

    Fuentes-Azcatl, Raúl; Barbosa, Marcia C.

    2018-02-01

    We propose a new force field for the Potassium Bromide, the KBr/ ε. The crystal density and structure, as well as, the density, the viscosity and the dielectric constant of the solution in water were computed and compared with the experiments and other atomistic models. Next, the transferability of the KBr/ ε and of the NaCl/ ε models is verified by creating the KCl/ ε and the NaBr/ ε models. The strategy was to employ the same parameters obtained for the NaCl/ ε and for the KBr/ ε force fields for the building up of the KCl/ ε and the NaBr/ ε models . The thermodynamic and dynamic properties of these two new models were compared with the experimental

  18. Minamata Convention on Mercury

    Science.gov (United States)

    On November 6, 2013 the United States signed the Minamata Convention on Mercury, a new multilateral environmental agreement that addresses specific human activities which are contributing to widespread mercury pollution

  19. Development of copper bromide laser master oscillator power ...

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... Development of master oscillator power amplifier (MOPA) system of copper bromide laser (CBL) operating at 110 W average power is reported. The spectral distribution of power at green (510.6 nm) and yellow (578.2 nm) components in the output of a copper bromide laser is studied as a function of ...

  20. Development of copper bromide laser master oscillator power

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... Development of master oscillator power amplifier (MOPA) system of copper bromide laser (CBL) operating at 110 W average power is reported. The spectral distribution of power at green (510.6 nm) and yellow (578.2 nm) components in the output of a copper bromide laser is studied as a function of ...

  1. Development of copper bromide laser master oscillator power ...

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... Abstract. Development of master oscillator power amplifier (MOPA) system of copper bromide laser (CBL) operating at 110 W average power is reported. The spectral distribution of power at green (510.6 nm) and yellow (578.2 nm) components in the output of a copper bromide laser is studied as a function ...

  2. Electric transport properties of alkali polymethacrylates in alkali bromide solutions

    NARCIS (Netherlands)

    Drift, W.P.J.T. van der; Overbeek, J.Th.G.

    Electric mobilities of polyions, bromide ions, and alkali ions have been determined in solutions of Li, Na, and K salts of polymethacrylic acid (PMA) in aqueous solutions of the corresponding bromide of concentrations varying from 0.001 to 0.1 M. The Hittorf method was used for the determination of

  3. Conduction bands and invariant energy gaps in alkali bromides

    NARCIS (Netherlands)

    Boer, P.K. de; Groot, R.A. de

    1998-01-01

    Electronic structure calculations of the alkali bromides LiBr, NaBr, KBr, RbBr and CsBr are reported. It is shown that the conduction band has primarily bromine character. The size of the band gaps of bromides and alkali halides in general is reinterpreted.

  4. Mercury in Your Environment

    Science.gov (United States)

    Basic information about mercury, how it gets in the air, how people are exposed to it and health effects associated with exposure; what EPA and other organizations are doing to limit exposures; what citizens should know to minimize exposures and to reduce mercury in the environment; and information about products that contain mercury.

  5. Intentional intravenous mercury injection

    African Journals Online (AJOL)

    Three forms of mercury exist: elemental, inorganic and organic, all of which may be toxic with clinical consequences, depending on the type of exposure. Elemental mercury poisoning usually occurs via vapour inhalation, as mercury is well absorbed through the lungs. The central nervous system is then the major site of ...

  6. Alkene- and Alkyne- Substituted Methylimidazolium Bromides: Structural Effects and Physical properties (Preprint)

    National Research Council Canada - National Science Library

    Schneider, Stefan; Drake, Gregory; Hall, Leslie; Hawkiins, Tommy; Rosander, Michael; Smith, Dennis

    2007-01-01

    .... X-ray structures of 1-(2-butynyl)-3-methylimidazolium bromide, 1-propargyl-3-methylimidazolium bromide as well as the X-ray structure of 1-allyl-3- methylimidazolium bromide which was previously identified as a room temperature ionic...

  7. Alkene- and alkyne- substituted methylimidazolium bromides: structural effects and Physical properties (Postprint)

    National Research Council Canada - National Science Library

    Schneider, Stefan; Drake, Gregory; Hall, Leslie; Hawkiins, Tommy; Rosander, Michael; Smith, Dennis

    2007-01-01

    .... X-ray structures of 1-(2-butynyl)-3-methylimidazolium bromide, 1-propargyl-3-methylimidazolium bromide as well as the X-ray structure of 1-allyl-3- methylimidazolium bromide which was previously identified as a room temperature ionic...

  8. Metastable fragmentation of silver bromide clusters

    International Nuclear Information System (INIS)

    L'Hermite, J.M.; Rabilloud, F.; Marcou, L.; Labastie, P.

    2001-01-01

    The abundance spectra and the fragmentation channels of silver bromide clusters have been measured and analyzed. The most abundant species are Ag n Br n - 1 + and Ag n Br n + 1 - and Ag 14 Br 13 + is a magic number, revealing their ionic nature. However, some features depart from what is generally observed for alkali-halide ionic clusters. From a certain size, Ag n Br n - 1 + is no more the main series, and Ag n Br n - 2, 3 + series become almost as important. The fast fragmentation induced by a UV laser makes the cations lose more bromine than silver ions and lead to more silver-rich clusters. Negative ions mass spectra contain also species with more silver atoms than required by stoichiometry. We have investigated the metastable fragmentation of the cations using a new experimental method. The large majority of the cations release mainly a neutral Ag 3 Br 3 cluster. These decay channels are in full agreement with our recent ab initio DFT calculations, which show that Ag + -Ag + repulsion is reduced due to a globally attractive interaction of their d orbitals. This effect leads to a particularly stable trimer (AgBr) 3 and to quasi-planar cyclic structures of (AgBr) n clusters up to n = 6. We have shown that these two features may be extended to other silver halides, to silver hydroxides (AgOH) n , and to cuprous halide compounds. (orig.)

  9. Intrapulmonary perfluorooctyl bromide instillation in fetal rabbits.

    Science.gov (United States)

    Muensterer, Oliver J; Klis, Verena J; Till, Holger; Bergmann, Florian; Metzger, Roman; Simbruner, Georg

    2005-07-01

    Instilling perfluorooctyl bromide (PFOB) into the fetal lung may lead to alveolar distension. The aim of the study was to evaluate the safety of PFOB instillation into fetal lungs and to determine the radiographic distribution and tissue concentration of PFOB in New Zealand white rabbits. Sibling fetuses of pregnant (day 27) New Zealand white rabbits were randomized to intratracheal instillation of 1 mL PFOB with tracheal ligation, instillation without ligation, and unmanipulated controls. The maternal animals were killed directly after instillation, at 3 or 6 hours (n = 10 each). For each study cohort, we determined fetal lung/body weight (FLBW) ratios, the radiographic distribution of PFOB, as well as pulmonary PFOB and water content by tissue distillation. PFOB concentrations in maternal and fetal tissues were assessed by gas chromatography. The relative amount of fetal lung PFOB recovered by fractional distillation was highest in ligated (25%) and lower in unligated lungs (9%). Extrapulmonary PFOB was found in the fetal brain (2.0 +/- 0.7 ppm), but not in any other fetal or maternal tissues. Mean FLBW ratios were highest in ligated fetuses, followed by unligated fetuses and controls. PFOB partially displaced fetal lung water. PFOB was visible in the lungs of all treated fetuses. Fetal survival between manipulated and unmanipulated fetuses did not differ. After prenatal intrapulmonary instillation, some PFOB remains in the lung, even if the trachea is not ligated, and may exert distending pressure on the alveoli.

  10. Mercury evaporation from amalgams with varied mercury contents.

    Science.gov (United States)

    Ohmoto, K; Nakajima, H; Ferracane, J L; Shintani, H; Okabe, T

    2000-09-01

    This study examined the relationship between mercury content and mercury evaporation from amalgams during setting. Two different types of commercial high-copper amalgams (single composition and admixed types) were used. Cylindrical specimens of each amalgam were prepared with five different mercury contents according to ADA Specification No.1. Specimens were also prepared by hand condensation. Mercury evaporation from amalgam specimens maintained at 37 degrees C was measured using a gold film mercury analyzer from 10 min after the end of trituration until the mercury concentration in air reached an undetectable level. The mercury content more clearly influenced the mercury evaporation from the admixed type amalgam specimens when the mercury content decreased below the manufacturers' recommended trituration conditions. Triturating with less mercury than the manufacturers' recommended amount cannot lower the evaporation of mercury from freshly made amalgam. Proper condensing procedures can minimize the mercury evaporation from the amalgam surface.

  11. Mercury balance analysis

    International Nuclear Information System (INIS)

    Maag, J.; Lassen, C.; Hansen, E.

    1996-01-01

    A detailed assessment of the consumption of mercury, divided into use areas, was carried out. Disposal and emissions to the environment were also qualified. The assessment is mainly based on data from 1992 - 1993. The most important source of emission of mercury to air is solid waste incineration which is assessed in particular to be due to the supply of mercury in batteries (most likely mercury oxide batteries from photo equipment) and to dental fillings. The second most important source of mercury emission to air is coal-fired power plants which are estimated to account for 200-500 kg of mercury emission p.a. Other mercury emissions are mainly related to waste treatment and disposal. The consumption of mercury is generally decreasing. During the period from 1982/83 - 1992-93, the total consumption of mercury in Denmark was about halved. This development is related to the fact that consumption with regard to several important use areas (batteries, dental fillings, thermometers etc.) has been significantly reduced, while for other purposes the use of mercury has completely, or almost disappeared, i.e. (fungicides for seed, tubes etc.). (EG)

  12. Bromide space, total body water, and sick cell syndrome

    International Nuclear Information System (INIS)

    Schober, O.; Hundeshagen, H.; Lehr, L.

    1982-01-01

    Displacements of the bromide space (Br-82-C, as a marker for the extracellular fluid compartment) are caused by an enhanced anatomical space and/or increased permeability of cells to bromide. The ratio Br-82-C: total body water (TBW) was evaluated to be 0.83 +- 0.17 in critically ill patients (n = 38) compared with the normal value of 0.46 +- 0.04 (n = 10). Because of normal TBW in critically ill patients (TBW = 505 +- 68 ml/kg), an increased bromide penetration into cells seems to be responsible for the enlarged ratio Br-82-C: TBW. Taking into consideration measurements in patients with malabsorption (Br-82-C: TBW = 0.56 +- 0.13; n = 13) and carcinoma of the rectum and colon (Br-82-C: TBW = 0.66 +- 0.24; n = 18) we think that the bromide space is a good measurement of the effective extracellular water. (orig.)

  13. Methyl Bromide Commodity Fumigation Buffer Zone Lookup Tables

    Science.gov (United States)

    Product labels for methyl bromide used in commodity and structural fumigation include requirements for buffer zones around treated areas. The information on this page will allow you to find the appropriate buffer zone for your planned application.

  14. Process for low mercury coal

    Science.gov (United States)

    Merriam, Norman W.; Grimes, R. William; Tweed, Robert E.

    1995-01-01

    A process for producing low mercury coal during precombustion procedures by releasing mercury through discriminating mild heating that minimizes other burdensome constituents. Said mercury is recovered from the overhead gases by selective removal.

  15. Disinfection byproduct regulatory compliance surrogates and bromide-associated risk.

    Science.gov (United States)

    Kolb, Chelsea; Francis, Royce A; VanBriesen, Jeanne M

    2017-08-01

    Natural and anthropogenic factors can alter bromide concentrations in drinking water sources. Increasing source water bromide concentrations increases the formation and alters the speciation of disinfection byproducts (DBPs) formed during drinking water treatment. Brominated DBPs are more toxic than their chlorinated analogs, and thus have a greater impact on human health. However, DBPs are regulated based on the mass sum of DBPs within a given class (e.g., trihalomethanes and haloacetic acids), not based on species-specific risk or extent of bromine incorporation. The regulated surrogate measures are intended to protect against not only the species they directly represent, but also against unregulated DBPs that are not routinely measured. Surrogates that do not incorporate effects of increasing bromide may not adequately capture human health risk associated with drinking water when source water bromide is elevated. The present study analyzes trihalomethanes (THMs), measured as TTHM, with varying source water bromide concentrations, and assesses its correlation with brominated THM, TTHM risk and species-specific THM concentrations and associated risk. Alternative potential surrogates are evaluated to assess their ability to capture THM risk under different source water bromide concentration conditions. The results of the present study indicate that TTHM does not adequately capture risk of the regulated species when source water bromide concentrations are elevated, and thus would also likely be an inadequate surrogate for many unregulated brominated species. Alternative surrogate measures, including THM 3 and the bromodichloromethane concentration, are more robust surrogates for species-specific THM risk at varying source water bromide concentrations. Copyright © 2017. Published by Elsevier B.V.

  16. Mercury is Moon's brother

    International Nuclear Information System (INIS)

    Ksanfomalifi, L.V.

    1976-01-01

    The latest information on Mercury planet is presented obtained by studying the planet with the aid of radar and space vehicles. Rotation of Mercury about its axis has been discovered; within 2/3 of its year it executes a complete revolution about its axis. In images obtained by the ''Mariner-10'' Mercurys surface differs little from that of the Moon. The ''Mariner-10'' has also discovered the Mercurys atmosphere, which consists of extremely rarefied helium. The helium is continuously supplied to the planet by the solar wind. The Mercury's magnetic field has been discovered, whose strength is 35 x 10 -4 at the Equator and 70 x 10 -4 E at the poles. The inclination of the dipole axis to the Mercury's rotation axis is 7 deg

  17. Peru Mercury Inventory 2006

    Science.gov (United States)

    Brooks, William E.; Sandoval, Esteban; Yepez, Miguel A.; Howard, Howell

    2007-01-01

    In 2004, a specific need for data on mercury use in South America was indicated by the United Nations Environmental Programme-Chemicals (UNEP-Chemicals) at a workshop on regional mercury pollution that took place in Buenos Aires, Argentina. Mercury has long been mined and used in South America for artisanal gold mining and imported for chlor-alkali production, dental amalgam, and other uses. The U.S. Geological Survey (USGS) provides information on domestic and international mercury production, trade, prices, sources, and recycling in its annual Minerals Yearbook mercury chapter. Therefore, in response to UNEP-Chemicals, the USGS, in collaboration with the Economic Section of the U.S. Embassy, Lima, has herein compiled data on Peru's exports, imports, and byproduct production of mercury. Peru was selected for this inventory because it has a 2000-year history of mercury production and use, and continues today as an important source of mercury for the global market, as a byproduct from its gold mines. Peru is a regional distributor of imported mercury and user of mercury for artisanal gold mining and chlor-alkali production. Peruvian customs data showed that 22 metric tons (t) of byproduct mercury was exported to the United States in 2006. Transshipped mercury was exported to Brazil (1 t), Colombia (1 t), and Guyana (1 t). Mercury was imported from the United States (54 t), Spain (19 t), and Kyrgyzstan (8 t) in 2006 and was used for artisanal gold mining, chlor-alkali production, dental amalgam, or transshipment to other countries in the region. Site visits and interviews provided information on the use and disposition of mercury for artisanal gold mining and other uses. Peru also imports mercury-containing batteries, electronics and computers, fluorescent lamps, and thermometers. In 2006, Peru imported approximately 1,900 t of a wide variety of fluorescent lamps; however, the mercury contained in these lamps, a minimum of approximately 76 kilograms (kg), and in

  18. Interaction of cephalosporin drugs with dodecyltrimethylammonium Bromide

    International Nuclear Information System (INIS)

    Hoque, Md. Anamul; Hossain, Mohammed Delwar; Khan, Mohammed Abdullah

    2013-01-01

    Highlights: • We carry out the interaction of cephalosporin drugs with DTAB conductometrically. • We examine the effect of drugs on the critical micelle concentration of DTAB. • Three critical micelle concentrations are obtained for drug- DTAB system. • Electrostatic and hydrophobic interactions between drugs and DTAB are proposed. • Drug supported micelle formation of DTAB is much favoured in aq. solution of K 2 SO 4 . -- Abstract: The interaction of three cephalosporin drugs namely cefadroxyl monohydrate (CFM), cephalexin monohydrate (CLM) and cephradine monohydrate (CDM) with dodecyltrimethylammonium Bromide (DTAB) has been carried out by conductance measurements in aqueous medium and in aqueous solution of K 2 SO 4 salt over temperature range of (303.15 to 318.15) K. For pure DTAB and drug-DTAB systems, three critical micelle concentrations were obtained. The third critical micelle concentration (c ∗ 3 ) indicates that the spherical micelle turns into rod shape that is sphere to rod transition. The c ∗ values of DTAB are changed due to the addition of cephalosporin drugs. In addition, the change of the values of c ∗ 1 , c ∗ 2 and c ∗ 3 with increase of the concentration of drugs indicate the presence of interaction between drug and DTAB. The c ∗ values indicate that micellization for the cephalosporins-surfactant systems in water follow the order: CFM-surfactant ∗ values for the cephalosporins - DTAB systems in aqueous K 2 SO 4 are lower in magnitude than those in pure water and the values decrease with increase of the concentrations of K 2 SO 4 at a particular temperature. A significant decrease of c ∗ values in the presence of K 2 SO 4 for cephalosporins-DTAB systems indicates that drug supported ionic micelle formation is much favoured in aqueous K 2 SO 4 solution compared to that in pure water. For cephalosporin-DTAB systems, ΔG 0 m values are negative which indicate that the drugs mediated ionic micelle formation processes are

  19. Modeling Mercury in Proteins

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Jeremy C [ORNL; Parks, Jerry M [ORNL

    2016-01-01

    Mercury (Hg) is a naturally occurring element that is released into the biosphere both by natural processes and anthropogenic activities. Although its reduced, elemental form Hg(0) is relatively non-toxic, other forms such as Hg2+ and, in particular, its methylated form, methylmercury, are toxic, with deleterious effects on both ecosystems and humans. Microorganisms play important roles in the transformation of mercury in the environment. Inorganic Hg2+ can be methylated by certain bacteria and archaea to form methylmercury. Conversely, bacteria also demethylate methylmercury and reduce Hg2+ to relatively inert Hg(0). Transformations and toxicity occur as a result of mercury interacting with various proteins. Clearly, then, understanding the toxic effects of mercury and its cycling in the environment requires characterization of these interactions. Computational approaches are ideally suited to studies of mercury in proteins because they can provide a detailed picture and circumvent issues associated with toxicity. Here we describe computational methods for investigating and characterizing how mercury binds to proteins, how inter- and intra-protein transfer of mercury is orchestrated in biological systems, and how chemical reactions in proteins transform the metal. We describe quantum chemical analyses of aqueous Hg(II), which reveal critical factors that determine ligand binding propensities. We then provide a perspective on how we used chemical reasoning to discover how microorganisms methylate mercury. We also highlight our combined computational and experimental studies of the proteins and enzymes of the mer operon, a suite of genes that confers mercury resistance in many bacteria. Lastly, we place work on mercury in proteins in the context of what is needed for a comprehensive multi-scale model of environmental mercury cycling.

  20. Thermodynamics of the interactions of some amino acids and peptides with dodecyltrimethylammonium bromide and tetradecyltrimethylammonium bromide

    International Nuclear Information System (INIS)

    Talele, Paurnima; Kishore, Nand

    2014-01-01

    Highlights: • Interactions of amino acids and peptides were studied with two cationic surfactants. • Partial molar properties and hydration numbers did not change significantly. • Measured properties indicate balance of polar and non-polar interactions. • Peptide bonds did not strengthen the extent of polar interactions with surfactant. • Results provide quantitative fine details of cationic surfactant–amino acids/peptides interactions. -- Abstract: The values of apparent molar volume V 2,ϕ and apparent molar adiabatic compressibility K S,2,ϕ of amino acids glycine, L-alanine, DL-α-amino-n-butyric acid, L-valine, L-leucine and peptides glycyl-glycine, glycyl-glycyl-glycine and glycyl-leucine have been determined in aqueous solutions of cationic surfactants dodecyltrimethylammonium bromide (DTAB) and tetradecyltrimethylammonium bromide (TTAB) by means of density and sound velocity measurements. The heat evolved or absorbed (q) during the course of interactions of amino acids and peptides with the aqueous solutions of surfactants were determined by isothermal titration calorimetry at T = 298.15 K. The values of standard partial molar volume V 2,m 0 and standard partial molar adiabatic compressibility K s,2,m 0 at infinite dilution were calculated from the values of V 2,ϕ and K S,2,ϕ . Similarly the values of limiting enthalpies of dilution (Δ dil H 0 ) of the amino acids/peptides were calculated from heat evolved or absorbed during calorimetric experiments. The standard partial molar quantities of transfer from water to aqueous surfactant solutions have been used to identify the interactions of amino acids and peptides with surfactants in terms of ionic–ionic, ionic–hydrophobic and hydrophobic–hydrophobic group interactions

  1. Intentional intravenous mercury injection

    African Journals Online (AJOL)

    In this case report, intravenous complications, treatment strategies and possible ... Mercury toxicity is commonly associated with vapour inhalation or oral ingestion, for which there exist definite treatment options. Intravenous mercury ... personality, anxiousness, irritability, insomnia, depression and drowsi- ness.[1] However ...

  2. International mercury conference

    CSIR Research Space (South Africa)

    Leaner, J

    2006-10-01

    Full Text Available Mercury (Hg) affects human health and the environment, it calls for immediate action. Action is needed at local, regional and international level to reduce the risk associated with mercury, which is a global international problem, as it is a...

  3. Mercury's shifting, rolling past

    OpenAIRE

    Trulove, Susan

    2008-01-01

    Patterns of scalloped-edged cliffs or lobate scarps on Mercury's surface are thrust faults that are consistent with the planet shrinking and cooling with time. However, compression occurred in the planet's early history and Mariner 10 images revealed decades ago that lobate scarps are among the youngest features on Mercury. Why don't we find more evidence of older compressive features?

  4. MESSENGER: Exploring Mercury's Magnetosphere

    Science.gov (United States)

    Slavin, James A.

    2008-01-01

    The MESSENGER mission to Mercury offers our first opportunity to explore this planet's miniature magnetosphere since Mariner 10's brief fly-bys in 1974-5. Mercury's magnetosphere is unique in many respects. The magnetosphere of Mercury is the smallest in the solar system with its magnetic field typically standing off the solar wind only - 1000 to 2000 km above the surface. For this reason there are no closed dri-fi paths for energetic particles and, hence, no radiation belts; the characteristic time scales for wave propagation and convective transport are short possibly coupling kinetic and fluid modes; magnetic reconnection at the dayside magnetopause may erode the subsolar magnetosphere allowing solar wind ions to directly impact the dayside regolith; inductive currents in Mercury's interior should act to modify the solar In addition, Mercury's magnetosphere is the only one with its defining magnetic flux tubes rooted in a planetary regolith as opposed to an atmosphere with a conductive ionosphere. This lack of an ionosphere is thought to be the underlying reason for the brevity of the very intense, but short lived, approx. 1-2 min, substorm-like energetic particle events observed by Mariner 10 in Mercury's magnetic tail. In this seminar, we review what we think we know about Mercury's magnetosphere and describe the MESSENGER science team's strategy for obtaining answers to the outstanding science questions surrounding the interaction of the solar wind with Mercury and its small, but dynamic magnetosphere.

  5. Global Mercury Assessment 2013

    International Development Research Centre (IDRC) Digital Library (Canada)

    mercury pollution. This summary report and the accompanying. Technical Background Report for the Global. Mercury Assessment 2013 are developed in response to Decision 25/5, paragraph ... The use of different pollution control technologies in different ...... vegetation, snow, freshwater, and seawater. One of the largest ...

  6. Interaction of cephradine monohydrate with Cetyldimethylethylammonium Bromide

    International Nuclear Information System (INIS)

    Hossain, Mohammed Delwar; Hoque, Md. Anamul

    2014-01-01

    Highlights: • We carry out the interaction of CDM drugs with CDMEAB conductometrically. • We examine the effect of drugs on the critical micelle concentration of CDMEAB. • Two critical micelle concentrations are obtained for drug-CDMEAB system. • Electrostatic and hydrophobic interactions between drug and surfactant are proposed. • Effect of KCl and K 2 SO 4 is observed on interaction between drug and surfactant. -- Abstract: Interaction of cephradine monohydrate (CDM) with Cetyldimethylethylammonium Bromide (CDMEAB) has been studied by conductance measurements in pure form and in the presence of salts like potassium chloride (KCl) and potassium sulphate (K 2 SO 4 ) over the temperature range of (298.15 to 318.15) K. From conductivity vs. surfactant concentration plots, two critical micelle concentrations like c 1 ∗ and c 1 ∗ were obtained for (CDM + CDMEAB) systems. The variation of c ∗ values of CDMEAB in the presence of CDM is the indication of the interaction between CDM and CDMEAB. For the (CDM + CDMEAB) system, the values of c ∗ values are higher in magnitude in contrast to that of pure CDMEAB in water over the range in temperature studied. In aqueous solutions of KCl and K 2 SO 4 , the c ∗ values are changed with the increase of the concentration of salts and hence the micellization is dependent on salt concentration. The ΔG m 0 values were negative and the spontaneity of micellization process is found to be increased with increase of temperature. The values of ΔH 1,m 0 and ΔS 1,m 0 indicated that the drug mediated CDMEAB aggregation in water was controlled at lower temperatures while at higher temperatures the aggregation was both enthalpy and entropy controlled. The ΔH 2,m 0 and ΔS 2,m 0 values revealed that the micellization in water was both enthalpy and entropy controlled at lower and higher temperatures though the effect of entropy at middle temperature was dominant. The results indicated that binding interactions between CDM

  7. Municipal actions to reduce mercury

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-03-15

    This paper presented proper management practices for products containing mercury. The measures can help reduce mercury releases, occupational exposure and mercury spills, thereby preventing impacts on human health and the environment. Despite mercury's toxic nature, many common products that contain mercury are commercially available. These include thermostats, thermometers, fluorescent lamps, pressure measuring devices, electrical switches and relays, and dental amalgam. Mercury emissions are also associated with base metal smelting, waste incineration and coal-fired power generation. Mercury in the environment is a global issue, because it can travel in the atmosphere on wind currents. The actions taken by municipalities to address the issue include reducing or eliminating mercury releases from internal municipal operations and sources within the community. This document provided guidance on how to develop a Municipal Mercury Elimination Policy and Plan that will help reduce mercury releases. It presented information and case studies that will help municipalities manage mercury-containing products found in municipal buildings and street lighting. Information on sources of mercury from within the community was presented along with case studies that can help municipalities determine where community action is needed to reduce mercury releases. The 5 modules of this document were intended to help municipalities identify priorities, timelines and budget requirements for mercury initiatives. It was emphasized that municipalities that adopt a Municipal Mercury Elimination Policy and Plan formally commit to reducing and eliminating mercury from the environment. tabs., figs.

  8. Getting Mercury out of Schools.

    Science.gov (United States)

    1999

    This guide was prepared while working with many Massachusetts schools to remove items that contain mercury and to find suitable alternatives. It contains fact sheets on: mercury in science laboratories and classrooms, mercury in school buildings and maintenance areas, mercury in the medical office and in medical technology classrooms in vocational…

  9. Determination of Rocuronium bromide by hydrophilic interaction liquid chromatography (HILIC

    Directory of Open Access Journals (Sweden)

    Natalija Nakov

    2012-01-01

    Full Text Available A new method involving hydrophilic interaction liquid chromatography (HILIC has been developed for determination of rocuronium bromide in presents of its main impurities (impurity A and impurity C, which are also its main degradation products, in solution for injection. The influence of the critical chromatographic parameters such as content of acetonitrile in the mobile phase, ionic strength and pH value of the buffer used in the mobile phase were investigated using the Design of experiments approach (DoE. The mechanism of retention of rocuronium bromide on bare silica column was also investigated. Optimal chromatographic conditions were obtained using mixture of acetonitrile and ammonium formate (107.5mM, pH 7.0 in ratio 90:10 as a mobile phase. The validation results have shown that the method is suitable for determination of rocuronium bromid in solution for injection.

  10. Photochemistry of alkyl bromides trapped in water ice films

    Science.gov (United States)

    Schrems, O.; Okaikwei, B.; Bluszcz, Th.

    2012-04-01

    Photochemical reactions of atmospheric trace gases taking place at the surface of atmospheric ice particles and in bulk ice are important in stratospheric and tropospheric chemistry but also in polar and alpine snowpack chemistry. Consequently, the understanding of the uptake und incorporation of atmospheric trace gases in water ice as well as their interactions with water molecules is very important for the understanding of processes which occur in ice particles and at the air/ice interface. Reactive atmospheric trace gases trapped in ice are subject of photochemical reactions when irradiated with solar UV radiation. Among such compounds bromine species are highly interesting due to their potential of depleting ozone both in the stratosphere and troposphere. Organic bromine gases can carry bromine to the stratosphere. Methyl bromide (CH3Br) is the largest bromine carrier to the stratosphere. It has both natural and anthropogenic sources. In this contribution we will present the results of our laboratory studies of alkyl bromides (methyl, bromide (CH3Br), dimethyl bromide (CH2Br2), n-propyl bromide (C3H7Br), 1,2-dibromoethane C2H4Br2)), trapped in water ice. We have simulated the UV photochemistry of these brominated alkanes isolated in ice films kept at 16 K and for comparison in solid argon matrices. The photoproducts formed in the ice have been identified by means of FTIR spectroscopy. Reflection absorption infrared spectroscopy (RAIRS) is especially useful to study nascent ice surfaces, kinetics of adsorption/decomposition, and heterogeneous catalysis. Among the observed photoproducts we could identify carbon monoxide and carbon dioxide for each alkyl bromide studied. The photoproduct HBr is dissociated in the bulk ice. Based on the experimental observations possible reaction mechanisms will be discussed.

  11. Mercury's Dynamic Magnetic Tail

    Science.gov (United States)

    Slavin, James A.

    2010-01-01

    The Mariner 10 and MESSENGER flybys of Mercury have revealed a magnetosphere that is likely the most responsive to upstream interplanetary conditions of any in the solar system. The source of the great dynamic variability observed during these brief passages is due to Mercury's proximity to the Sun and the inverse proportionality between reconnection rate and solar wind Alfven Mach number. However, this planet's lack of an ionosphere and its small physical dimensions also contribute to Mercury's very brief Dungey cycle, approx. 2 min, which governs the time scale for internal plasma circulation. Current observations and understanding of the structure and dynamics of Mercury's magnetotail are summarized and discussed. Special emphasis will be placed upon such questions as: 1) How much access does the solar wind have to this small magnetosphere as a function of upstream conditions? 2) What roles do heavy planetary ions play? 3) Do Earth-like substorms take place at Mercury? 4) How does Mercury's tail respond to extreme solar wind events such coronal mass ejections? Prospects for progress due to advances in the global magnetohydrodynamic and hybrid simulation modeling and the measurements to be taken by MESSENGER after it enters Mercury orbit on March 18, 2011 will be discussed.

  12. Inorganic: the other mercury.

    Science.gov (United States)

    Risher, John F; De Rosa, Christopher T

    2007-11-01

    There is a broad array of mercury species to which humans may be exposed. While exposure to methylmercury through fish consumption is widely recognized, the public is less aware of the sources and potential toxicity of inorganic forms of mercury. Some oral and laboratory thermometers, barometers, small batteries, thermostats, gas pressure regulators, light switches, dental amalgam fillings, cosmetic products, medications, cultural/religious practices, and gold mining all represent potential sources of exposure to inorganic forms of mercury. The route of exposure, the extent of absorption, the pharmacokinetics, and the effects all vary with the specific form of mercury and the magnitude and duration of exposure. If exposure is suspected, a number of tissue analyses can be conducted to confirm exposure or to determine whether an exposure might reasonably be expected to be biologically significant. By contrast with determination of exposure to methylmercury, for which hair and blood are credible indicators, urine is the preferred biological medium for the determination of exposure to inorganic mercury, including elemental mercury, with blood normally being of value only if exposure is ongoing. Although treatments are available to help rid the body of mercury in cases of extreme exposure, prevention of exposure will make such treatments unnecessary. Knowing the sources of mercury and avoiding unnecessary exposure are the prudent ways of preventing mercury intoxication. When exposure occurs, it should be kept in mind that not all unwanted exposures will result in adverse health consequences. In all cases, elimination of the source of exposure should be the first priority of public health officials.

  13. Recovery of mercury from mercury compounds via electrolytic methods

    Science.gov (United States)

    Grossman, Mark W.; George, William A.

    1988-01-01

    A process for electrolytically recovering mercury from mercury compounds is provided. In one embodiment, Hg is recovered from Hg.sub.2 Cl.sub.2 employing as the electrolyte solution a mixture of HCl and H.sub.2 O. In another embodiment, Hg is electrolytically recovered from HgO wherein the electrolyte solution is comprised of glacial acetic acid and H.sub.2 O. Also provided is an apparatus for producing isotopically enriched mercury compounds in a reactor and then transporting the dissolved compounds into an electrolytic cell where mercury ions are electrolytically reduced and elemental mercury recovered from the mercury compounds.

  14. The tectonics of Mercury

    International Nuclear Information System (INIS)

    Melosh, H.J.; Mckinnon, W.B.

    1988-01-01

    The probable tectonic history of Mercury and the relative sequence of events are discussed on the basis of data collected by the Mariner-10 spacecraft. Results indicate that Mercury's tectonic activity was confined to its early history; its endogenic activity was principally due to a small change in the shape of its lithosphere, caused by tidal despinning, and a small change in area caused by shrinkage due to cooling. Exogenic processes, in particular the impact activity, have produced more abundant tectonic features. Many features associated with the Caloris basin are due to loading of Mercury's thick lithosphere by extrusive lavas or subsidence due to magma withdrawal. It is emphasized that tectonic features observed on Mercury yield insight into the earliest tectonic events on planets like Mars and, perhaps, the earth, where subsequent events obscured or erased the most ancient tectonic records

  15. 7 CFR 305.6 - Methyl bromide fumigation treatment schedules.

    Science.gov (United States)

    2010-01-01

    ... 12 40 or above 16 8 T408-g-1 Chamber 60 or above 10 24 60 or above 20 15.5 T408-g-2 Tarpaulin 60 or..., fumigation with methyl bromide for sapote fruit fly. Regulated citrus fruits originating inside an area quarantined for sapote fruit fly that are to be moved outside the quarantined area may be treated with methyl...

  16. REVIEW OF CONTROL OPTIONS FOR METHYL BROMIDE IN COMMODITY TREATMENT

    Science.gov (United States)

    The report describes recent developments in the control of methyl bromide (MeBr) and discusses technical considerations and requirements for and economic feasibility of recovery. (NOTE: MeBr, fumigant for agricultural commodities, is an ozone depleting chemical. The U.S. EPA has ...

  17. Methyl bromide phase out could affect future reforestation efforts

    Science.gov (United States)

    Methyl bromide has long been an integral component in producing healthy tree seedlings in forest nurseries of California, Idaho, Montana, Oregon and Washington. The fumigant was supposed to be completely phased out of use in the United States of America by 2005, but many forest nurseries continue to...

  18. Study of methyl bromide reactivity with human and mouse hemoglobin

    African Journals Online (AJOL)

    A study has been carried out on in-vitro reactivity of human and mouse hemoglobin spectrophotometrically at physiological pH, using different protein to reagent ratios. Hemoglobin side chains were modified with different concentrations of methyl bromide on agro-soil fumigant. To ascertain if the site of alkylation was the ...

  19. Revisiting the Kinetics and Mechanism of Bromate-Bromide Reaction

    Directory of Open Access Journals (Sweden)

    Côrtes Carlos Eduardo S.

    2001-01-01

    Full Text Available The bromate-bromide reaction was investigated in an acidity range not studied yet. The reaction was followed at the Br2/Br3- isosbestic point (lambda = 446 nm. It was observed a first-order behavior for bromate and bromide ions and a second-order behavior for H+ ion that results in the rate law nu = k[BrO3-][Br- ][H+]². This rate law suggests a mechanism involving two successive protonation of bromate followed by the interaction of the intermediate species H2BrO3+ with bromide. These results disagree with the obtained by other authors who observed a second-order behavior for the bromide and first-order for H+, and have proposed intermediate species like H2Br2O3 and HBr2O3-. The second-order for [H+] observed in the range 0.005 <= [H+] <= 2.77 mol L-1 sets down that the pKa of bromic acid, HBrO3, must be lower than -0.5 (T = 25 °C, different from all other values for this pKa proposed in the literature.

  20. Ipratropium bromide delivered by metered-dose aerosol to infant ...

    African Journals Online (AJOL)

    1990-08-21

    Aug 21, 1990 ... Two methods of administration of ipratropium bromide. (Atrovent; Boehringer Ingelheim) to wheezing children'< 25 months of age were compared: (I) the conventional nebulisa- tion (15 children); and (iI) a metered-dose aerosol plus spacer and mask (MDA group, 17 children). The drug induced a significant ...

  1. Ipratropium bromide delivered by metered-dose aerosol to infant ...

    African Journals Online (AJOL)

    Two methods of administration of ipratropium bromide (Atrovent; Boehringer Ingelheim) to wheezing children'< 25 months of age were compared: (i) the conventional nebulisation (15 children); and (ii) a metered-dose aerosol plus spacer and mask (MDA group, 17 children). The drug induced a significant and similar fall in ...

  2. Exposure to methyl bromide during greenhouse fumigation on Crete, Greece

    NARCIS (Netherlands)

    Vreede, J.A.F. de; Boeft, J. den; Hemmen, J.J. van

    1998-01-01

    In agricultural areas where greenhouses and dwellings are intermixed, the general population as well as the professional applicators may be exposed to pesticides. In a field study on Crete, exposure to methyl bromide during soil fumigation was assessed. Exposure of applicators (both contractors and

  3. Development of copper bromide laser master oscillator power ...

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... Da; 42.60.Jf. 1. Introduction. The copper bromide laser (CBL) is a prominent laser belonging to the class of copper halide lasers [1,2], which are developed to overcome the problems of pure metal copper ... pseudo-Gaussian beam intensity profile that is better suited for many applications than the top-hat ...

  4. Mercury CEM Calibration

    Energy Technology Data Exchange (ETDEWEB)

    John F. Schabron; Joseph F. Rovani; Susan S. Sorini

    2007-03-31

    The Clean Air Mercury Rule (CAMR) which was published in the Federal Register on May 18, 2005, requires that calibration of mercury continuous emissions monitors (CEMs) be performed with NIST-traceable standards. Western Research Institute (WRI) is working closely with the Electric Power Research Institute (EPRI), the National Institute of Standards and Technology (NIST), and the Environmental Protection Agency (EPA) to facilitate the development of the experimental criteria for a NIST traceability protocol for dynamic elemental mercury vapor generators. The traceability protocol will be written by EPA. Traceability will be based on the actual analysis of the output of each calibration unit at several concentration levels ranging from about 2-40 ug/m{sup 3}, and this analysis will be directly traceable to analyses by NIST using isotope dilution inductively coupled plasma/mass spectrometry (ID ICP/MS) through a chain of analyses linking the calibration unit in the power plant to the NIST ID ICP/MS. Prior to this project, NIST did not provide a recommended mercury vapor pressure equation or list mercury vapor pressure in its vapor pressure database. The NIST Physical and Chemical Properties Division in Boulder, Colorado was subcontracted under this project to study the issue in detail and to recommend a mercury vapor pressure equation that the vendors of mercury vapor pressure calibration units can use to calculate the elemental mercury vapor concentration in an equilibrium chamber at a particular temperature. As part of this study, a preliminary evaluation of calibration units from five vendors was made. The work was performed by NIST in Gaithersburg, MD and Joe Rovani from WRI who traveled to NIST as a Visiting Scientist.

  5. Mercury in human hair

    International Nuclear Information System (INIS)

    Kapauan, P.A.; Cruz, C.C.; Verceluz, F.P.

    1980-10-01

    The analysis of mercury (Hg) in scalp hair obtained from individuals residing in five different localities in the Philippines - Metro Manila, Naga City in Bicol, Bataan, Oriental Mindoro, and Palawan is presented. An overall mean of 1.46 ug/g of hair was obtained for all samples excluding those from Palawan and represents a baseline value.'' In terms of the mercury levels found in hair, the Honda Bay area in Palawan is, relatively, a ''contaminated area.'' (author)

  6. Method and apparatus for monitoring mercury emissions

    Science.gov (United States)

    Durham, Michael D.; Schlager, Richard J.; Sappey, Andrew D.; Sagan, Francis J.; Marmaro, Roger W.; Wilson, Kevin G.

    1997-01-01

    A mercury monitoring device that continuously monitors the total mercury concentration in a gas. The device uses the same chamber for converting speciated mercury into elemental mercury and for measurement of the mercury in the chamber by radiation absorption techniques. The interior of the chamber is resistant to the absorption of speciated and elemental mercury at the operating temperature of the chamber.

  7. Bromide and other ions in the snow, firn air, and atmospheric boundary layer at Summit during GSHOX

    Directory of Open Access Journals (Sweden)

    J. E. Dibb

    2010-10-01

    Full Text Available Measurements of gas phase soluble bromide in the boundary layer and in firn air, and Br in aerosol and snow, were made at Summit, Greenland (72.5° N, 38.4° W, 3200 m a.s.l. as part of a larger investigation into the influence of Br chemistry on HOx cycling. The soluble bromide measurements confirm that photochemical activation of Br in the snow causes release of active Br to the overlying air despite trace concentrations of Br in the snow (means 15 and 8 nmol Br kg−1 of snow in 2007 and 2008, respectively. Mixing ratios of soluble bromide above the snow were also found to be very small (mean <1 ppt both years, with maxima of 3 and 4 ppt in 2007 and 2008, respectively, but these levels clearly oxidize and deposit long-lived gaseous elemental mercury and may perturb HOx partitioning. Concentrations of Br in surface snow tended to increase/decrease in parallel with the specific activities of the aerosol-associated radionuclides 7Be and 210Pb. Earlier work has shown that ventilation of the boundary layer causes simultaneous increases in 7Be and 210Pb at Summit, suggesting there is a pool of Br in the free troposphere above Summit in summer time. Speciation and the source of this free tropospheric Br are not well constrained, but we suggest it may be linked to extensive regions of active Br chemistry in the Arctic basin which are known to cause ozone and mercury depletion events shortly after polar sunrise. If this hypothesis is correct, it implies persistence of the free troposphere Br for several months after peak Br activation in March/April. Alternatively, there may be a ubiquitous pool of Br in the free troposphere, sustained by currently unknown sources and processes.

  8. Mercury pollution in Malaysia.

    Science.gov (United States)

    Hajeb, Parvaneh; Jinap, S; Ismail, Ahmad; Mahyudin, Nor Ainy

    2012-01-01

    Although several studies have been published on levels of mercury contamination of the environment, and of food and human tissues in Peninsular Malaysia, there is a serious dearth of research that has been performed in East Malaysia (Sabah and Sarawak). Industry is rapidly developing in East Malaysia, and, hence, there is a need for establishing baseline levels of mercury contamination in environmental media in that part of the country by performing monitoring studies. Residues of total mercury and inorganic in food samples have been determined in nearly all previous studies that have been conducted; however, few researchers have analyzed samples for the presence of methlymercury residues. Because methylmercury is the most toxic form of mercury, and because there is a growing public awareness of the risk posed by methylmercury exposure that is associated with fish and seafood consumption, further monitoring studies on methylmercury in food are also essential. From the results of previous studies, it is obvious that the economic development in Malaysia, in recent years, has affected the aquatic environment of the country. Primary areas of environmental concern are centered on the rivers of the west Peninsular Malaysian coast, and the coastal waters of the Straits of Malacca, wherein industrial activities are rapidly expanding. The sources of existing mercury input to both of these areas of Malaysia should be studied and identified. Considering the high levels of mercury that now exists in human tissues, efforts should be continued, and accelerated in the future, if possible, to monitor mercury contamination levels in the coastal states, and particularly along the west Peninsular Malaysian coast. Most studies that have been carried out on mercury residues in environmental samples are dated, having been conducted 20-30 years ago; therefore, the need to collect much more and more current data is urgent. Furthermore, establishing baseline levels of mercury exposure to

  9. Fabrication of mercury target vessel

    International Nuclear Information System (INIS)

    Wakui, Takashi; Kogawa, Hiroyuki; Haga, Katsuhiro; Futakawa, Masatoshi; Hayashi, Ryoichi; Uchiyama, Naoyoshi; Okamoto, Yoshinao; Nakamura, Koji

    2010-03-01

    The construction of materials and life science experimental facility in J-PARC (Japan Proton Accelerator Complex) project had been completed and accepted pulsed proton beams with low power. Since 2003, the detailed design, fabrication and examination for the mercury target vessel as a pulsed neutron source were carried out by the vender. The mercury target vessel consists of triple-walled structure in order to prevent the leak of mercury to outside at the failure of the mercury vessel and to remove the heat of the safety hull, which covers the mercury vessel, due to the injection of the pulsed proton beams. The high fabrication accuracy is required for the mercury target vessel assembled by the welding, because there are the relationships between the mercury target vessel and other components (target trolley, target storage container, flange of helium vessel, reflector and water-cooled shield). At each fabrication step, the examinations for the mercury target vessel with multi-walled structure were required. In this report, the required specification and basic structure of parts in the mercury target vessel are described and the fabrication procedure of the mercury target vessel by the vender is reported. In the fabrication of the mercury target vessel, there were many troubles such as large deformation due to the welding and then the vender repaired and brought the mercury target vessel to completion. Furthermore, improvements for the design and fabrication of the mercury target are reported. (author)

  10. Uptake of ozone to mixed sodium bromide/ citric acid solutions

    Science.gov (United States)

    Lee, Ming-Tao; Steimle, Emilie; Bartels-Rausch, Thorsten; Kato, Shunsuke; Lampimäki, Markus; Brown, Matthew; van Bokhoven, Jeroen; Nolting, Frithjof; Kleibert, Armin; Türler, Andreas; Ammann, Markus

    2013-04-01

    Sea-salt solution - air interfaces play an important role in the chemistry of the marine boundary layer. The reaction of ozone (O3) with bromide is of interest in the context of formation of photolabile halogens (Br2, BrCl) in the marine boundary layer. Recent experiments have suggested that the bromide oxidation rate is related to the surface concentration of bromide [1] and inversely related to the gas phase concentration of O3, an indication for a precursor mediated reaction at the surface [2]. So far, the effect of organics (such as those occurring at the ocean surface or in marine aerosols) on the reaction of O3 with bromide aerosols has not been studied yet. In our study we investigate the uptake kinetics of O3 to a mixed solution of sodium bromide (NaBr) and citric acid (CA), which represents highly oxidized organic compounds present in the environment, with a well-established coated wall flow tube technique, which leads to exposure of the film to O3 allowing the heterogeneous reactions to take place and the loss of O3 being measured. The results indicate that the uptake of O3 to the films with the higher bromide concentrations (0.34M and 4M) is independent of the gas phase concentration and roughly consistent with uptake limited by reaction in the bulk. For the lower bromide concentration (84mM), however, we observe a trend of the uptake coefficient to decrease with increasing O3 concentration, indicating an increasing importance of a surface reaction. In an attempt to constrain the kinetic data, we employed X-ray photoelectron spectroscopy (XPS) to get insight into the surface composition of the aqueous solution - air interface. Previous XPS studies have shown that halide ion concentrations are enhanced at the aqueous solution air interface [3-4], which likely promotes the surface reactions of bromide or iodide with O3. A first XPS study of ternary solutions of KI with butanol indicated the importance of specific interactions of the cation with the alcohol

  11. Association of defects in lead chloride and lead bromide: Ionic conductivity and dielectric loss measurements

    NARCIS (Netherlands)

    Brom, W.E. van den; Schoonman, J.; Wit, J.H.W. de

    The ionic conductivity data of pure and doped lead bromide without associated defects are used in order to explain the anomalous conductivity behaviour of copper (I) bromide and lead oxide-doped lead-bromide crystals. In these crystals precipitated dopant and associated defects are present. The

  12. Mercury Emissions: The Global Context

    Science.gov (United States)

    Mercury emissions are a global problem that knows no national or continental boundaries. Mercury that is emitted to the air can travel thousands of miles in the atmosphere before it is eventually deposited back to the earth.

  13. Comparison and Analysis of Lithium Bromide-water Absorption Chillers Using Plastic Heat Transfer Tubes and Traditional Lithium Bromide-water Absorption Chillers

    OpenAIRE

    Xue-dong Zhang

    2010-01-01

    There are extensive applications of lithium bromide-water absorption chillers in industry, but the heat exchangers corrosion and refrigerating capacity loss are very difficult to be solved. In this paper, an experiment was conducted by using plastic heat transfer tubes instead of copper tubes. As an example, for a lithium bromide-water absorption chiller of refrigerating capacity of 35kW, the correlative performance of the lithium bromide-water absorption chiller using pl...

  14. Mercury's magnetic field and interior

    International Nuclear Information System (INIS)

    Connerney, J.E.P.; Ness, N.F.

    1988-01-01

    The magnetic-field data collected on Mercury by the Mariner-10 spacecraft present substantial evidence for an intrinsic global magnetic field. However, studies of Mercury's thermal evolution show that it is most likely that the inner core region of Mercury solidified or froze early in the planet's history. Thus, the explanation of Mercury's magnetic field in the framework of the traditional planetary dynamo is less than certain

  15. Reference Atmosphere for Mercury

    Science.gov (United States)

    Killen, Rosemary M.

    2002-01-01

    We propose that Ar-40 measured in the lunar atmosphere and that in Mercury's atmosphere is due to current diffusion into connected pore space within the crust. Higher temperatures at Mercury, along with more rapid loss from the atmosphere will lead to a smaller column abundance of argon at Mercury than at the Moon, given the same crustal abundance of potassium. Because the noble gas abundance in the Hermean atmosphere represents current effusion, it is a direct measure of the crustal potassium abundance. Ar-40 in the atmospheres of the planets is a measure of potassium abundance in the interiors, since Ar-40 is a product of radiogenic decay of K-40 by electron capture with the subsequent emission of a 1.46 eV gamma-ray. Although the Ar-40 in the Earth's atmosphere is expected to have accumulated since the late bombardment, Ar-40 in the atmospheres of Mercury and the Moon is eroded quickly by photoionization and electron impact ionization. Thus, the argon content in the exospheres of the Moon and Mercury is representative of current effusion rather than accumulation over the lifetime of the planet.

  16. Mercury content of edible mushrooms

    Energy Technology Data Exchange (ETDEWEB)

    Woidich, H.; Pfannhauser, W.

    1975-05-01

    The mercury content of edible fungi is different. Relatively high burdened are Boletus and Agaricus campestris. A minimum of mercury is found in Russula, Agaricus bisporus and Cantharellus cibarius. The possibilities of mercury uptake and the potential cumulation mechanism is discussed. 8 references, 3 tables.

  17. Mercury (Environmental Health Student Portal)

    Science.gov (United States)

    ... Water Waterborne Diseases & Illnesses Water Cycle Water Treatment Mercury The Basics Mercury — sometimes called quicksilver — is a natural metal. It’s ... to breathe it in without knowing it. When mercury combines with other chemical elements, it creates compounds, ...

  18. Aluminum electroplating on steel from a fused bromide electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat K. Tripathy; Laura A. Wurth; Eric J. Dufek; Toni Y. Gutknecht; Natalie J. Gese; Paula Hahn; Steven M. Frank; Guy L. Frederickson; J. Stephen Herring

    2014-08-01

    A quaternary bromide bath (LiBr–KBr–CsBr–AlBr3) was used to electro-coat aluminum on steel substrates. The electrolytewas prepared by the addition of AlBr3 into the eutectic LiBr–KBr–CsBr melt. A smooth, thick, adherent and shiny aluminum coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminum coverage. Both salt immersion and open circuit potential measurement suggested that the coatings did display a good corrosionresistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminum coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminumcoating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

  19. Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat Tripathy; Laura Wurth; Eric Dufek; Toni Y. Gutknecht; Natalie Gese; Paula Hahn; Steven Frank; Guy Fredrickson; J Stephen Herring

    2014-08-01

    A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

  20. Sensing Mercury for Biomedical and Environmental Monitoring

    Directory of Open Access Journals (Sweden)

    Julia Xiaojun Zhao

    2009-07-01

    Full Text Available Mercury is a very toxic element that is widely spread in the atmosphere, lithosphere, and surface water. Concentrated mercury poses serious problems to human health, as bioaccumulation of mercury within the brain and kidneys ultimately leads to neurological diseases. To control mercury pollution and reduce mercury damage to human health, sensitive determination of mercury is important. This article summarizes some current sensors for the determination of both abiotic and biotic mercury. A wide array of sensors for monitoring mercury is described, including biosensors and chemical sensors, while piezoelectric and microcantilever sensors are also described. Additionally, newly developed nanomaterials offer great potential for fabricating novel mercury sensors. Some of the functional fluorescent nanosensors for the determination of mercury are covered. Afterwards, the in vivo determination of mercury and the characterization of different forms of mercury are discussed. Finally, the future direction for mercury detection is outlined, suggesting that nanomaterials may provide revolutionary tools in biomedical and environmental monitoring of mercury.

  1. Pyridostimine Bromide 30mg Stability in Extended Storage Conditions

    Science.gov (United States)

    2017-12-03

    SUPPLEMENTARY NOTES American Society of Health-System Pharmacists, 14. ABSTRACT 2017 American Society of Health-System Pharmacists (ASHP) Midyear...34Prescribed by ANSI Std. Z39.18 Adobe Professional 7.0 2017 American Society of Health-System Pharmacists (ASHP) Midyear Resident Poster Abstract...limit 100 words): Pyridostigmine bromide 30mg is approved by the Federal Drug Administration (FDA) as a pre-treatment of nerve gas exposure. The

  2. High-speed Laser Micromachining with Copper Bromide Laser

    OpenAIRE

    Balchev, Ivaylo I.; Minkovski, Nikolai I.; Kostadinov, Ivan K.; Sabotinov, Nikola V.

    2006-01-01

    The application of the copper bromide (CuBr) laser as an attractive tool in the micro-machining of different materials has been demonstrated. High-quality drilling by trepanning and precision cutting was established on several materials with a negligible heat-affected zone (HAZ). That good performance was a result of the combination of high power visible radiation, short pulses, and close to the diffraction-limited laser beam quality with high-speed galvo scanner beam steering.

  3. On the existence of 'L-alanine cadmium bromide'.

    Science.gov (United States)

    Srinivasan, Bikshandarkoil R

    2013-12-01

    It is argued that the recently reported nonlinear optical crystal L-alanine cadmium bromide, grown by slow solvent evaporation method at room temperature [P. Ilayabarathi, J. Chandrasekaran, Spectrochim. Acta 96A (2012) 684-689] is the well-known L-alanine crystal. The isolation of L-alanine crystal is explained due to fractional crystallization. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. Water displacement mercury pump

    Science.gov (United States)

    Nielsen, M.G.

    1984-04-20

    A water displacement mercury pump has a fluid inlet conduit and diffuser, a valve, a pressure cannister, and a fluid outlet conduit. The valve has a valve head which seats in an opening in the cannister. The entire assembly is readily insertable into a process vessel which produces mercury as a product. As the mercury settles, it flows into the opening in the cannister displacing lighter material. When the valve is in a closed position, the pressure cannister is sealed except for the fluid inlet conduit and the fluid outlet conduit. Introduction of a lighter fluid into the cannister will act to displace a heavier fluid from the cannister via the fluid outlet conduit. The entire pump assembly penetrates only a top wall of the process vessel, and not the sides or the bottom wall of the process vessel. This insures a leak-proof environment and is especially suitable for processing of hazardous materials.

  5. Mercury CEM Calibration

    Energy Technology Data Exchange (ETDEWEB)

    John Schabron; Joseph Rovani; Mark Sanderson

    2008-02-29

    Mercury continuous emissions monitoring systems (CEMS) are being implemented in over 800 coal-fired power plant stacks. The power industry desires to conduct at least a full year of monitoring before the formal monitoring and reporting requirement begins on January 1, 2009. It is important for the industry to have available reliable, turnkey equipment from CEM vendors. Western Research Institute (WRI) is working closely with the Electric Power Research Institute (EPRI), the National Institute of Standards and Technology (NIST), and the Environmental Protection Agency (EPA) to facilitate the development of the experimental criteria for a NIST traceability protocol for dynamic elemental mercury vapor generators. The generators are used to calibrate mercury CEMs at power plant sites. The Clean Air Mercury Rule (CAMR) which was published in the Federal Register on May 18, 2005 requires that calibration be performed with NIST-traceable standards (Federal Register 2007). Traceability procedures will be defined by EPA. An initial draft traceability protocol was issued by EPA in May 2007 for comment. In August 2007, EPA issued an interim traceability protocol for elemental mercury generators (EPA 2007). The protocol is based on the actual analysis of the output of each calibration unit at several concentration levels ranging initially from about 2-40 {micro}g/m{sup 3} elemental mercury, and in the future down to 0.2 {micro}g/m{sup 3}, and this analysis will be directly traceable to analyses by NIST. The document is divided into two separate sections. The first deals with the qualification of generators by the vendors for use in mercury CEM calibration. The second describes the procedure that the vendors must use to certify the generator models that meet the qualification specifications. The NIST traceable certification is performance based, traceable to analysis using isotope dilution inductively coupled plasma/mass spectrometry performed by NIST in Gaithersburg, MD. The

  6. Spatial Variation Scales of Rainfall Characteristics and Bromide Leaching

    Science.gov (United States)

    Wendroth, O. O.; Vasquez, V.; Matocha, C.

    2010-12-01

    Amount and intensity of rainfall are known as important characteristics that affect the leaching of surface-applied agri-chemicals. Besides these, the effect of the time interval between a fertilizer, pesticide or tracer application and subsequent rainfall on solute leaching is not well understood. Moreover, little is known about the spatial representativity of the solute concentration based on a relatively small soil sample in field-scale transport studies. To know the spatial representativity of a solute concentration sample at a time is crucial for analyzing solute leaching behavior over time as well as over space. The objectives of this study were to identify the impact of rainfall intensity and amount as well as the application time delay on solute transport in a well-drained Maury silt loam soil. Moreover, an experimental design and protocol had to be developed that exhibited spatial variability structure and representativity of bromide concentration. For this purpose, the variation scale of each of the factors investigated was chosen differently to apply frequency domain statistics. The study was conducted in a Maury silt loam soil at the University of Kentucky, College of Agriculture Experimental Farm Spindletop. Along a 64-m transect, 32 plots each 2-m long and 4-m wide were established. The three different treatments were spatially laid out in sinusoidal patterns at three respective wavelengths. Two different rainfall amounts were applied in blocks of eight consecutive plots, hence a wavelength of 32 m. These two different rainfall amounts were applied at four rates, spatially distributed in two waves each of 16 m length. Individual plots received the irrigation at specific times after the tracer had been applied. Four application delay times were chosen, hence the wavelength for this treatment was 8 m. Bromide concentration was measured for soil samples that were taken with a percussion auger at every 50 cm distance along the 64-m-transect. Auger cores

  7. Solid miscibility of common-anion lithium and sodium halides. Experimental determination of the region of demixing in lithium bromide + sodium bromide

    NARCIS (Netherlands)

    Oonk, H.A.J.; Wijk, H.J. van; Doornhof, D.

    1984-01-01

    The region of demixing of solid lithium bromide + sodium bromide mixtures has been measured by X-ray diffraction. The critical temperature of mixing corresponding to a thermodynamic fit of the experimental data is 513 K. Estimates are given of the regions of demixing in solid lithium chloride +

  8. On the distribution of bromide and bromide/chlorinity ratios in the waters of the Arabian sea off central Indian coast

    Digital Repository Service at National Institute of Oceanography (India)

    DeSouza, F.P.; SenGupta, R.

    Water samples from surface to 2000 m depth at two stations in the Arabian Sea collected during the 82nd cruise of R V Gaveshani in November, 1980 were analysed for bromide. The average bromide concentration was 0.068 g/kg plus or minus 0...

  9. Method and apparatus for sampling atmospheric mercury

    Science.gov (United States)

    Trujillo, Patricio E.; Campbell, Evan E.; Eutsler, Bernard C.

    1976-01-20

    A method of simultaneously sampling particulate mercury, organic mercurial vapors, and metallic mercury vapor in the working and occupational environment and determining the amount of mercury derived from each such source in the sampled air. A known volume of air is passed through a sampling tube containing a filter for particulate mercury collection, a first adsorber for the selective adsorption of organic mercurial vapors, and a second adsorber for the adsorption of metallic mercury vapor. Carbon black molecular sieves are particularly useful as the selective adsorber for organic mercurial vapors. The amount of mercury adsorbed or collected in each section of the sampling tube is readily quantitatively determined by flameless atomic absorption spectrophotometry.

  10. Mercury analysis in hair

    DEFF Research Database (Denmark)

    Esteban, Marta; Schindler, Birgit Karin; Jiménez, José Antonio

    2015-01-01

    laboratories. Training sessions were organized for field workers and four external quality-assessment exercises (ICI/EQUAS), followed by the corresponding web conferences, were organized between March 2011 and February 2012. ICI/EQUAS used native hair samples at two mercury concentration ranges (0...

  11. Mercury exposure in Ireland

    DEFF Research Database (Denmark)

    Cullen, Elizabeth; Evans, David S; Davidson, Fred

    2014-01-01

    of a study to Coordinate and Perform Human Biomonitoring on a European Scale (DEMOCOPHES) pilot biomonitoring study. METHODS: Hair mercury concentrations were determined from a convenience sample of 120 mother/child pairs. Mothers also completed a questionnaire. Rigorous quality assurance within DEMOCOPHES...

  12. Metabolic models for methyl and inorganic mercury

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, S.R.; Purdue, P.

    1984-03-01

    Following the outbreak of mercury poisoning in Minimata, Japan (1953-60), much work has been done on the toxicology of mercury - in particular methyl mercury. In this paper, the authors derive two compartmental models for the metabolism of methyl mercury and inorganic mercury based upon the data which have been collected since 1960.

  13. [Mercury in vaccines].

    Science.gov (United States)

    Hessel, Luc

    2003-01-01

    Thiomersal, also called thimerosal, is an ethyl mercury derivative used as a preservative to prevent bacterial contamination of multidose vaccine vials after they have been opened. Exposure to low doses of thiomersal has essentially been associated with hypersensitivity reactions. Nevertheless there is no evidence that allergy to thiomersal could be induced by thiomersal-containing vaccines. Allergy to thiomersal is usually of delayed-hypersensitivity type, but its detection through cutaneous tests is not very reliable. Hypersensitivity to thiomersal is not considered as a contraindication to the use of thiomersal-containing vaccines. In 1999 in the USA, thiomersal was present in approximately 30 different childhood vaccines, whereas there were only 2 in France. Although there were no evidence of neurological toxicity in infants related to the use of thiomersal-containing vaccines, the FDA considered that the cumulative dose of mercury received by young infants following vaccination was high enough (although lower than the FDA threshold for methyl mercury) to request vaccine manufacturers to remove thiomersal from vaccine formulations. Since 2002, all childhood vaccines used in Europe and the USA are thiomersal-free or contain only minute amounts of thiomersal. Recently published studies have shown that the mercury levels in the blood, faeces and urine of children who had received thiomersal-containing vaccines were much lower than those accepted by the American Environmental Protection Agency. It has also been demonstrated that the elimination of mercury in children was much faster than what was expected on the basis of studies conducted with methyl mercury originating from food. Recently, the hypothesis that mercury contained in vaccines could be the cause of autism and other neurological developmental disorders created a new debate in the medical community and the general public. To date, none of the epidemiological studies conducted in Europe and elsewhere

  14. Mercury Information Clearinghouse

    Energy Technology Data Exchange (ETDEWEB)

    Chad A. Wocken; Michael J. Holmes; Dennis L. Laudal; Debra F. Pflughoeft-Hassett; Greg F. Weber; Nicholas V. C. Ralston; Stanley J. Miller; Grant E. Dunham; Edwin S. Olson; Laura J. Raymond; John H. Pavlish; Everett A. Sondreal; Steven A. Benson

    2006-03-31

    The Canadian Electricity Association (CEA) identified a need and contracted the Energy & Environmental Research Center (EERC) to create and maintain an information clearinghouse on global research and development activities related to mercury emissions from coal-fired electric utilities. With the support of CEA, the Center for Air Toxic Metals{reg_sign} (CATM{reg_sign}) Affiliates, and the U.S. Department of Energy (DOE), the EERC developed comprehensive quarterly information updates that provide a detailed assessment of developments in the various areas of mercury monitoring, control, policy, and research. A total of eight topical reports were completed and are summarized and updated in this final CEA quarterly report. The original quarterly reports can be viewed at the CEA Web site (www.ceamercuryprogram.ca). In addition to a comprehensive update of previous mercury-related topics, a review of results from the CEA Mercury Program is provided. Members of Canada's coal-fired electricity generation sector (ATCO Power, EPCOR, Manitoba Hydro, New Brunswick Power, Nova Scotia Power Inc., Ontario Power Generation, SaskPower, and TransAlta) and CEA, have compiled an extensive database of information from stack-, coal-, and ash-sampling activities. Data from this effort are also available at the CEA Web site and have provided critical information for establishing and reviewing a mercury standard for Canada that is protective of environment and public health and is cost-effective. Specific goals outlined for the CEA mercury program included the following: (1) Improve emission inventories and develop management options through an intensive 2-year coal-, ash-, and stack-sampling program; (2) Promote effective stack testing through the development of guidance material and the support of on-site training on the Ontario Hydro method for employees, government representatives, and contractors on an as-needed basis; (3) Strengthen laboratory analytical capabilities through

  15. Small Mercury Relativity Orbiter

    Science.gov (United States)

    Bender, Peter L.; Vincent, Mark A.

    1989-01-01

    The accuracy of solar system tests of gravitational theory could be very much improved by range and Doppler measurements to a Small Mercury Relativity Orbiter. A nearly circular orbit at roughly 2400 km altitude is assumed in order to minimize problems with orbit determination and thermal radiation from the surface. The spacecraft is spin-stabilized and has a 30 cm diameter de-spun antenna. With K-band and X-band ranging systems using a 50 MHz offset sidetone at K-band, a range accuracy of 3 cm appears to be realistically achievable. The estimated spacecraft mass is 50 kg. A consider-covariance analysis was performed to determine how well the Earth-Mercury distance as a function of time could be determined with such a Relativity Orbiter. The minimum data set is assumed to be 40 independent 8-hour arcs of tracking data at selected times during a two year period. The gravity field of Mercury up through degree and order 10 is solved for, along with the initial conditions for each arc and the Earth-Mercury distance at the center of each arc. The considered parameters include the gravity field parameters of degree 11 and 12 plus the tracking station coordinates, the tropospheric delay, and two parameters in a crude radiation pressure model. The conclusion is that the Earth-Mercury distance can be determined to 6 cm accuracy or better. From a modified worst-case analysis, this would lead to roughly 2 orders of magnitude improvement in the knowledge of the precession of perihelion, the relativistic time delay, and the possible change in the gravitational constant with time.

  16. Mercury Phase II Study - Mercury Behavior in Salt Processing Flowsheet

    Energy Technology Data Exchange (ETDEWEB)

    Jain, V. [Savannah River Remediation, LLC., Aiken, SC (United States); Shah, H. [Savannah River Remediation, LLC., Aiken, SC (United States). Sludge and Salt Planning; Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Wilmarth, W. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-07-25

    Mercury (Hg) in the Savannah River Site Liquid Waste System (LWS) originated from decades of canyon processing where it was used as a catalyst for dissolving the aluminum cladding of reactor fuel. Approximately 60 metric tons of mercury is currently present throughout the LWS. Mercury has long been a consideration in the LWS, from both hazard and processing perspectives. In February 2015, a Mercury Program Team was established at the request of the Department of Energy to develop a comprehensive action plan for long-term management and removal of mercury. Evaluation was focused in two Phases. Phase I activities assessed the Liquid Waste inventory and chemical processing behavior using a system-by-system review methodology, and determined the speciation of the different mercury forms (Hg+, Hg++, elemental Hg, organomercury, and soluble versus insoluble mercury) within the LWS. Phase II activities are building on the Phase I activities, and results of the LWS flowsheet evaluations will be summarized in three reports: Mercury Behavior in the Salt Processing Flowsheet (i.e. this report); Mercury Behavior in the Defense Waste Processing Facility (DWPF) Flowsheet; and Mercury behavior in the Tank Farm Flowsheet (Evaporator Operations). The evaluation of the mercury behavior in the salt processing flowsheet indicates, inter alia, the following: (1) In the assembled Salt Batches 7, 8 and 9 in Tank 21, the total mercury is mostly soluble with methylmercury (MHg) contributing over 50% of the total mercury. Based on the analyses of samples from 2H Evaporator feed and drop tanks (Tanks 38/43), the source of MHg in Salt Batches 7, 8 and 9 can be attributed to the 2H evaporator concentrate used in assembling the salt batches. The 2H Evaporator is used to evaporate DWPF recycle water. (2) Comparison of data between Tank 21/49, Salt Solution Feed Tank (SSFT), Decontaminated Salt Solution Hold Tank (DSSHT), and Tank 50 samples suggests that the total mercury as well as speciated

  17. Mercury Phase II Study - Mercury Behavior in Salt Processing Flowsheet

    International Nuclear Information System (INIS)

    Jain, V.; Shah, H.; Wilmarth, W. R.

    2016-01-01

    Mercury (Hg) in the Savannah River Site Liquid Waste System (LWS) originated from decades of canyon processing where it was used as a catalyst for dissolving the aluminum cladding of reactor fuel. Approximately 60 metric tons of mercury is currently present throughout the LWS. Mercury has long been a consideration in the LWS, from both hazard and processing perspectives. In February 2015, a Mercury Program Team was established at the request of the Department of Energy to develop a comprehensive action plan for long-term management and removal of mercury. Evaluation was focused in two Phases. Phase I activities assessed the Liquid Waste inventory and chemical processing behavior using a system-by-system review methodology, and determined the speciation of the different mercury forms (Hg+, Hg++, elemental Hg, organomercury, and soluble versus insoluble mercury) within the LWS. Phase II activities are building on the Phase I activities, and results of the LWS flowsheet evaluations will be summarized in three reports: Mercury Behavior in the Salt Processing Flowsheet (i.e. this report); Mercury Behavior in the Defense Waste Processing Facility (DWPF) Flowsheet; and Mercury behavior in the Tank Farm Flowsheet (Evaporator Operations). The evaluation of the mercury behavior in the salt processing flowsheet indicates, inter alia, the following: (1) In the assembled Salt Batches 7, 8 and 9 in Tank 21, the total mercury is mostly soluble with methylmercury (MHg) contributing over 50% of the total mercury. Based on the analyses of samples from 2H Evaporator feed and drop tanks (Tanks 38/43), the source of MHg in Salt Batches 7, 8 and 9 can be attributed to the 2H evaporator concentrate used in assembling the salt batches. The 2H Evaporator is used to evaporate DWPF recycle water. (2) Comparison of data between Tank 21/49, Salt Solution Feed Tank (SSFT), Decontaminated Salt Solution Hold Tank (DSSHT), and Tank 50 samples suggests that the total mercury as well as speciated

  18. A mercury transport and fate model (LM2-mercury) for mass budget assessment of mercury cycling in Lake Michigan

    Science.gov (United States)

    LM2-Mercury, a mercury mass balance model, was developed to simulate and evaluate the transport, fate, and biogeochemical transformations of mercury in Lake Michigan. The model simulates total suspended solids (TSS), disolved organic carbon (DOC), and total, elemental, divalent, ...

  19. Mercury Exposure and Heart Diseases.

    Science.gov (United States)

    Genchi, Giuseppe; Sinicropi, Maria Stefania; Carocci, Alessia; Lauria, Graziantonio; Catalano, Alessia

    2017-01-12

    Environmental contamination has exposed humans to various metal agents, including mercury. It has been determined that mercury is not only harmful to the health of vulnerable populations such as pregnant women and children, but is also toxic to ordinary adults in various ways. For many years, mercury was used in a wide variety of human activities. Nowadays, the exposure to this metal from both natural and artificial sources is significantly increasing. Recent studies suggest that chronic exposure, even to low concentration levels of mercury, can cause cardiovascular, reproductive, and developmental toxicity, neurotoxicity, nephrotoxicity, immunotoxicity, and carcinogenicity. Possible biological effects of mercury, including the relationship between mercury toxicity and diseases of the cardiovascular system, such as hypertension, coronary heart disease, and myocardial infarction, are being studied. As heart rhythm and function are under autonomic nervous system control, it has been hypothesized that the neurotoxic effects of mercury might also impact cardiac autonomic function. Mercury exposure could have a long-lasting effect on cardiac parasympathetic activity and some evidence has shown that mercury exposure might affect heart rate variability, particularly early exposures in children. The mechanism by which mercury produces toxic effects on the cardiovascular system is not fully elucidated, but this mechanism is believed to involve an increase in oxidative stress. The exposure to mercury increases the production of free radicals, potentially because of the role of mercury in the Fenton reaction and a reduction in the activity of antioxidant enzymes, such as glutathione peroxidase. In this review we report an overview on the toxicity of mercury and focus our attention on the toxic effects on the cardiovascular system.

  20. Mercury Exposure and Heart Diseases

    Directory of Open Access Journals (Sweden)

    Giuseppe Genchi

    2017-01-01

    Full Text Available Environmental contamination has exposed humans to various metal agents, including mercury. It has been determined that mercury is not only harmful to the health of vulnerable populations such as pregnant women and children, but is also toxic to ordinary adults in various ways. For many years, mercury was used in a wide variety of human activities. Nowadays, the exposure to this metal from both natural and artificial sources is significantly increasing. Recent studies suggest that chronic exposure, even to low concentration levels of mercury, can cause cardiovascular, reproductive, and developmental toxicity, neurotoxicity, nephrotoxicity, immunotoxicity, and carcinogenicity. Possible biological effects of mercury, including the relationship between mercury toxicity and diseases of the cardiovascular system, such as hypertension, coronary heart disease, and myocardial infarction, are being studied. As heart rhythm and function are under autonomic nervous system control, it has been hypothesized that the neurotoxic effects of mercury might also impact cardiac autonomic function. Mercury exposure could have a long-lasting effect on cardiac parasympathetic activity and some evidence has shown that mercury exposure might affect heart rate variability, particularly early exposures in children. The mechanism by which mercury produces toxic effects on the cardiovascular system is not fully elucidated, but this mechanism is believed to involve an increase in oxidative stress. The exposure to mercury increases the production of free radicals, potentially because of the role of mercury in the Fenton reaction and a reduction in the activity of antioxidant enzymes, such as glutathione peroxidase. In this review we report an overview on the toxicity of mercury and focus our attention on the toxic effects on the cardiovascular system.

  1. EFFICACY OF HYOSCINE BUTYL BROMIDE SUPPOSITORY FOR POSTOPERATIVE PAIN RELIEF

    Directory of Open Access Journals (Sweden)

    Soniya C. Alphonse

    2017-07-01

    Full Text Available BACKGROUND Caesarean Section is on the rise all over the world. Women undergoing Caesarean section often wish to be awake post operatively and to avoid excessive medications affecting interactions with the new born infant. Multimodal pain therapy has been advocated for postoperative pain management after caesarean section. MATERIALS AND METHODS The study is a prospective randomized controlled study conducted at a tertiary care hospital to study the effect of Hyoscine Butyl Bromide Suppositories for postoperative analgesia following elective repeat caesarean section. The study included sixty patients divided into two groups- Group1 (study group were given Hyoscine Butyl Bromide Suppository (10 mg along with Injection. Tramadol 50 mg IM and Group II (control group were given Injection Tramadol IM only at the end of surgery. Pain score of the patient assessed at 1 hr, 2 hrs, 6hrs and 24 hrs post operatively. The total no of doses of injection tramadol needed in 24 hrs and the interval between 1st and 2nd dose of tramadol was also noted. The adverse effects of the drug and additional advantages of the drug if any were also assessed. RESULTS There was no statistically significant difference in pain score during the assessment intervals between the two groups. There was no difference in the number of doses of tramadol needed in the first 24 hrs. The mean interval between the 1st and 2nd dose of tramadol was found to be 7.6538 hours for group 1 patients and 6.9130 for group patients which was found to be statistically significant. There was no statistically significant side effects/ additional advantages for the drugs. CONCLUSION Concurrent administration of Hyoscine Butyl Bromide Suppository (10 mg and injection Tramadol 50 mg IM offers a longer postoperative analgesia without any increased adverse effects.

  2. Mercury's exosphere: observations during MESSENGER's First Mercury flyby.

    Science.gov (United States)

    McClintock, William E; Bradley, E Todd; Vervack, Ronald J; Killen, Rosemary M; Sprague, Ann L; Izenberg, Noam R; Solomon, Sean C

    2008-07-04

    During MESSENGER's first Mercury flyby, the Mercury Atmospheric and Surface Composition Spectrometer measured Mercury's exospheric emissions, including those from the antisunward sodium tail, calcium and sodium close to the planet, and hydrogen at high altitudes on the dayside. Spatial variations indicate that multiple source and loss processes generate and maintain the exosphere. Energetic processes connected to the solar wind and magnetospheric interaction with the planet likely played an important role in determining the distributions of exospheric species during the flyby.

  3. Suicide by intravenous injection of rocuronium-bromide: Case report

    Directory of Open Access Journals (Sweden)

    Nikolić Slobodan

    2005-01-01

    Full Text Available Suicides by intravenous injection of an overdose of medicaments are uncommon. In this paper, we present the case of a suicide by rocuronium-bromide injection in combination with an oral overdose of metoprolol. Unfortunately, in Belgrade, there is no toxicological laboratory capable of detecting rocuronium. The interpretation of autopsy and toxicological data in this case was made difficult due to the extreme putrefaction of the body of the deceased. So, by forensic investigation, the case was solved indirectly, through circumstantial evidence: an empty ampoule of rocuronium found near the body, as well as a plastic syringe and cloth-bandage found in the left hand of the deceased.

  4. Tiotropium Bromide in Chronic Obstructive Pulmonary Disease and Bronchial Asthma.

    Science.gov (United States)

    Alvarado-Gonzalez, Alcibey; Arce, Isabel

    2015-11-01

    Inhaled bronchodilators are the mainstay of pharmacological treatment for stable chronic obstructive pulmonary disease (COPD), including β2-agonists and muscarinic antagonists. Tiotropium bromide, a long-acting antimuscarinic bronchodilator (LAMA), is a treatment choice for moderate-to-severe COPD; its efficacy and safety have been demonstrated in recent trials. Studies also point to a beneficial role of tiotropium in the treatment of difficult-to-control asthma and a potential function in the asthma-COPD overlap syndrome (ACOS). Combination of different bronchodilator molecules and addition of inhaled corticosteroids are viable therapeutic alternatives. A condensation of the latest trials and the rationale behind these therapies will be presented in this article.

  5. Recovery of mercury from acid waste residues

    Science.gov (United States)

    Greenhalgh, Wilbur O.

    1989-12-05

    Mercury can be recovered from nitric acid-containing fluids by reacting the fluid with aluminum metal to produce mercury metal, and then quenching the reactivity of the nitric acid prior to nitration of the mercury metal.

  6. Mercury Poisoning Linked to Skin Products

    Science.gov (United States)

    ... Products For Consumers Home For Consumers Consumer Updates Mercury Poisoning Linked to Skin Products Share Tweet Linkedin ... and, in some situations, criminal prosecution. Dangers of Mercury Exposure to mercury can have serious health consequences. ...

  7. Morphology of silver bromide crystals produced at presence of N,N -dimethylformamide

    Energy Technology Data Exchange (ETDEWEB)

    Dyonizy, A.; Nowak, P. [Institute of Physical and Theoretical Chemistry, Wroclaw University of Technology (Poland)

    2010-08-15

    The study deals with examination of conditions that are necessary to obtain flat crystals of silver bromide that grow in a water and gelatine crystallization environment where N,N -dimethylformamide is used as the agent that is conducive to complexing of sparingly soluble silver bromide. The examination focused on the issue how changes in volumetric concentration of N,N -dimethylformamide as well as concentration of excessive ions of silver bromide in the dispersive solution affect morphology and size of newly created of silver bromide. The completed experiments enabled to determine boundary limits of both N,N -dimethylformamide and bromide ions concentration where suspensions of silver bromide crystals exhibit predominant content of triangular, transient and hexagonal flat forms with very high aspect ratio. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  8. Obtaining tabular silver bromide crystals using double-jet method in the presence of dimethyl sulfoxide

    Energy Technology Data Exchange (ETDEWEB)

    Dyonizy, A.; Nowak, P. [Institute of Physical and Theoretical Chemistry, Wroclaw University of Technology, Wybrzeze St., Wyspianskiego 27, 50-370 Wroclaw (Poland)

    2010-11-15

    Water-gelatine suspensions containing tabular crystals of silver bromide were obtained using the modified double-jet method, in the presence of dimethyl sulfoxide and an excess of bromide ions, used to increase silver bromide solubility. The size and morphology of crystals obtained depend mostly on the constant concentration of complexing agents in the dispersive solution, during nucleation and crystal growth. The influence of excessive bromide ions concentration and volumetric concentration of dimethyl sulfoxide in the crystallising mixture on the formation of tabular - triangular or hexagonal thin plates - of high aspect ratio has been analysed. During experiment, optimal ranges of dimethyl sulfoxide and excessive bromide ions concentrations for obtaining interesting forms of flat silver bromide crystals were determined. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  9. In vitro evaluation of inorganic and methyl mercury mediated cytotoxic effect on neural cells derived from different animal species.

    Science.gov (United States)

    Tong, Jing; Wang, Youwei; Lu, Yuanan

    2016-03-01

    To extend the current understanding of the mercury-mediated cytotoxic effect, five neural cell lines established from different animal species were comparatively analyzed using three different endpoint bioassays: thiazolyl blue tetrazolium bromide, 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide assay (MTT), neutral red uptake assay (NRU), and Coomassie blue assay (CB). Following a 24-hr exposure to selected concentrations of mercury chloride (HgCl2) and methylmercury (II) chloride (MeHgCl), the cytotoxic effect on test cells was characterized by comparing their 50% inhibition concentration (IC50) values. Experimental results indicated that both these forms of mercury were toxic to all the neural cells, but at very different degrees. The IC50 values of MeHgCl among these cell lines ranged from 1.15±0.22 to 10.31±0.70μmol/L while the IC50 values for HgCl2 were much higher, ranging from 6.44±0.36 to 160.97±19.63μmol/L, indicating the more toxic nature of MeHgCl. The IC50 ratio between HgCl2 and MeHgCl ranged from 1.75 to 96.0, which confirms that organic mercury is much more toxic to these neural cells than inorganic mercury. Among these cell lines, HGST-BR and TriG44 derived from marine sea turtles showed a significantly high tolerance to HgCl2 as compared to the three mammalian neural cells. Among these neural cells, SK-N-SH represented the most sensitive cells to both chemical forms of mercury. Copyright © 2015. Published by Elsevier B.V.

  10. Mercury, Vaccines, and Autism

    Science.gov (United States)

    Baker, Jeffrey P.

    2008-01-01

    The controversy regarding the once widely used mercury-containing preservative thimerosal in childhood vaccines has raised many historical questions that have not been adequately explored. Why was this preservative incorporated in the first place? Was there any real evidence that it caused harm? And how did thimerosal become linked in the public mind to the “autism epidemic”? I examine the origins of the thimerosal controversy and their legacy for the debate that has followed. More specifically, I explore the parallel histories of three factors that converged to create the crisis: vaccine preservatives, mercury poisoning, and autism. An understanding of this history provides important lessons for physicians and policymakers seeking to preserve the public’s trust in the nation’s vaccine system. PMID:18172138

  11. Mercury in Canadian crude oil

    International Nuclear Information System (INIS)

    Hollebone, B.P.

    2005-01-01

    Estimates for average mercury concentrations in crude oil range widely from 10 ng/g of oil to 3,500 ng/g of oil. With such a broad range of estimates, it is difficult to determine the contributions of the petroleum sector to the total budget of mercury emissions. In response to concerns that the combustion of petroleum products may be a major source of air-borne mercury pollution, Environment Canada and the Canadian Petroleum Products Institute has undertaken a survey of the average total mercury concentration in crude oil processed in Canadian refineries. In order to calculate the potential upper limit of total mercury in all refined products, samples of more than 30 different types of crude oil collected from refineries were measured for their concentration of mercury as it enters into a refinery before processing. High temperature combustion, cold vapour atomic absorption and cold vapour atomic fluorescence were the techniques used to quantify mercury in the samples. The results of the study provide information on the total mass of mercury present in crude oil processed in Canada each year. Results can be used to determine the impact of vehicle exhaust emissions to the overall Canadian mercury emission budget. 17 refs., 2 tabs., 2 figs

  12. Transient neuromyopathy after bromide intoxication in a dog with idiopathic epilepsy

    Directory of Open Access Journals (Sweden)

    Steinmetz Sonja

    2012-12-01

    Full Text Available Abstract A seven-year old Australian Shepherd, suffering from idiopathic epilepsy under treatment with phenobarbitone and potassium bromide, was presented with generalised lower motor neuron signs. Electrophysiology and muscle-nerve biopsies revealed a neuromyopathy. The serum bromide concentration was increased more than two-fold above the upper reference value. Clinical signs disappeared after applying diuretics and reducing the potassium bromide dose rate. This is the first case report describing electrophysiological and histopathological findings associated with bromide induced lower motor neuron dysfunction in a dog.

  13. Method for mercury refinement

    Science.gov (United States)

    Grossman, M.W.; Speer, R.; George, W.A.

    1991-04-09

    The effluent from mercury collected during the photochemical separation of the [sup 196]Hg isotope is often contaminated with particulate mercurous chloride, Hg[sub 2]Cl[sub 2]. The use of mechanical filtering via thin glass tubes, ultrasonic rinsing with acetone (dimethyl ketone) and a specially designed cold trap have been found effective in removing the particulate (i.e., solid) Hg[sub 2]Cl[sub 2] contaminant. The present invention is particularly directed to such filtering. 5 figures.

  14. Apparatus for mercury refinement

    Science.gov (United States)

    Grossman, M.W.; Speer, R.; George, W.A.

    1991-07-16

    The effluent from mercury collected during the photochemical separation of the [sup 196]Hg isotope is often contaminated with particulate mercurous chloride, Hg[sub 2]Cl[sub 2]. The use of mechanical filtering via thin glass tubes, ultrasonic rinsing with acetone (dimethyl ketone) and a specially designed cold trap have been found effective in removing the particulate (i.e., solid) Hg[sub 2]Cl[sub 2] contaminant. The present invention is particularly directed to such filtering. 5 figures.

  15. Apparatus for mercury refinement

    International Nuclear Information System (INIS)

    Grossman, M.W.; Speer, R.; George, W.A.

    1991-01-01

    The effluent from mercury collected during the photochemical separation of the 196 Hg isotope is often contaminated with particulate mercurous chloride, Hg 2 Cl 2 . The use of mechanical filtering via thin glass tubes, ultrasonic rinsing with acetone (dimethyl ketone) and a specially designed cold trap have been found effective in removing the particulate (i.e., solid) Hg 2 Cl 2 contaminant. The present invention is particularly directed to such filtering. 5 figures

  16. Magnetic field of Mercury

    International Nuclear Information System (INIS)

    Jackson, D.J.; Beard, D.B.

    1977-01-01

    The geomagnetic field, suitably scaled down and parameterized, is shown to give a very good fit to the magnetic field measurements taken on the first and third passes of the Mariner 10 space probe past Mercury. The excellence of the fit to a reliable planetary magnetospheric model is good evidence that the Mercury magnetosphere is formed by a simple, permanent, intrinsic planetary magnetic field distorted by the effects of the solar wind. The parameters used for a best fit to all the data are (depending slightly on the choice of data) 2.44--2.55 for the ratio of Mercury's magnetic field strength at the subsolar point to that of the earth's subsolar point field (this results in a dipole moment of 170 γR/sub M/ 3 (R/sub M/ is Mercury Radius), i.e., 2.41 x 10 22 G cm 3 in the same direction as the earth's dipole), approx.-113 γR/sub M/ 4 for the planetary quadrupole moment parallel to the dipole moment, 10degree--17degree for the tilt of the planet dipole toward the sun, 4.5degree for the tilt of the dipole toward dawn, and 2.5degree--7.6degree aberration angle for the shift in the tail axis from the planet-sun direction because of the planet's orbital velocity. The rms deviation overall for the entire data set compared with the theoretical fitted model for the magnetic field strength was 17 γ (approx.4% of the maximum field measured). If the data from the first pass that show presumed strong time variations are excluded, the overall rms deviation for the field magnitude is only 10 γ

  17. The planet Mercury (1971)

    Science.gov (United States)

    1972-01-01

    The physical properties of the planet Mercury, its surface, and atmosphere are presented for space vehicle design criteria. The mass, dimensions, mean density, and orbital and rotational motions are described. The gravity field, magnetic field, electromagnetic radiation, and charged particles in the planet's orbit are discussed. Atmospheric pressure, temperature, and composition data are given along with the surface composition, soil mechanical properties, and topography, and the surface electromagnetic and temperature properties.

  18. Mercury's Magnetic Field

    Science.gov (United States)

    Johnson, C. L.

    2014-12-01

    Mercury is the only inner solar system body other than Earth to possess an active core dynamo-driven magnetic field and the only planet with a small, highly dynamic magnetosphere. Measurements made by the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft have provided a wealth of data on Mercury's magnetic field environment. Mercury's weak magnetic field was discovered 40 years ago by the Mariner 10 spacecraft, but its large-scale geometry, strength and origin could not be definitively established. MESSENGER data have shown that the field is dynamo-generated and can be described as an offset axisymmetric dipole field (hereafter OAD): the magnetic equator lies ~0.2 RM (RM = 2440 km) north of the geographic equator and the dipole moment is 2.8 x1019 Am2 (~0.03% that of Earth's). The weak internal field and the high, but variable, solar wind ram pressure drive vigorous magnetospheric dynamics and result in an average distance from the planet center to the sub-solar magnetopause of only 1.42 RM. Magnetospheric models developed with MESSENGER data have allowed re-analysis of the Mariner 10 observations, establishing that there has been no measureable secular variation in the internal field over 40 years. Together with spatial power spectra for the OAD, this provides critical constraints for viable dynamo models. Time-varying magnetopause fields induce secondary core fields, the magnitudes of which confirm the core radius estimated from MESSENGER gravity and Earth-based radar data. After accounting for large-scale magnetospheric fields, residual signatures are dominated by additional external fields that are organized in the local time frame and that vary with magnetospheric activity. Birkeland currents have been identified, which likely close in the planetary interior at depths below the base of the crust. Near-periapsis magnetic field measurements at altitudes greater than 200 km have tantalizing hints of crustal fields, but crustal

  19. Vapour pressures, densities, and viscosities of the (water + lithium bromide + potassium acetate) system and (water + lithium bromide + sodium lactate) system

    International Nuclear Information System (INIS)

    Lucas, Antonio de; Donate, Marina; Rodriguez, Juan F.

    2006-01-01

    Measurements of thermophysical properties (vapour pressure, density, and viscosity) of the (water + lithium bromide + potassium acetate) system LiBr:CH 3 COOK = 2:1 by mass ratio and the (water + lithium bromide + sodium lactate) system LiBr:CH 3 CH(OH)COONa = 2:1 by mass ratio were measured. The system, a possible new working fluid for absorption heat pump, consists of absorbent (LiBr + CH 3 COOK) or (LiBr + CH 3 CH(OH)COONa) and refrigerant H 2 O. The vapour pressures were measured in the ranges of temperature and absorbent concentration from T = (293.15 to 333.15) K and from mass fraction 0.20 to 0.50, densities and viscosities were measured from T = (293.15 to 323.15) K and from mass fraction 0.20 to 0.40. The experimental data were correlated with an Antoine-type equation. Densities and viscosities were measured in the same range of temperature and absorbent concentration as that of the vapour pressure. Regression equations for densities and viscosities were obtained with a minimum mean square error criterion

  20. Vapour pressures, densities, and viscosities of the (water + lithium bromide + potassium acetate) system and (water + lithium bromide + sodium lactate) system

    Energy Technology Data Exchange (ETDEWEB)

    Lucas, Antonio de [Department of Chemical Engineering, University of Castilla - La Mancha, Avda. de Camilo Jose Cela s/n, 13004 Ciudad Real (Spain); Donate, Marina [Department of Chemical Engineering, University of Castilla - La Mancha, Avda. de Camilo Jose Cela s/n, 13004 Ciudad Real (Spain); Rodriguez, Juan F. [Department of Chemical Engineering, University of Castilla - La Mancha, Avda. de Camilo Jose Cela s/n, 13004 Ciudad Real (Spain)]. E-mail: juan.rromero@uclm.es

    2006-02-15

    Measurements of thermophysical properties (vapour pressure, density, and viscosity) of the (water + lithium bromide + potassium acetate) system LiBr:CH{sub 3}COOK = 2:1 by mass ratio and the (water + lithium bromide + sodium lactate) system LiBr:CH{sub 3}CH(OH)COONa = 2:1 by mass ratio were measured. The system, a possible new working fluid for absorption heat pump, consists of absorbent (LiBr + CH{sub 3}COOK) or (LiBr + CH{sub 3}CH(OH)COONa) and refrigerant H{sub 2}O. The vapour pressures were measured in the ranges of temperature and absorbent concentration from T = (293.15 to 333.15) K and from mass fraction 0.20 to 0.50, densities and viscosities were measured from T = (293.15 to 323.15) K and from mass fraction 0.20 to 0.40. The experimental data were correlated with an Antoine-type equation. Densities and viscosities were measured in the same range of temperature and absorbent concentration as that of the vapour pressure. Regression equations for densities and viscosities were obtained with a minimum mean square error criterion.

  1. Mercury: Exploration of a Planet

    Science.gov (United States)

    1976-01-01

    The flight of the Mariner 10 spacecraft to Venus and Mercury is detailed in animation and photography. Views of Mercury are featured. Also included is animation on the origin of the solar system. Dr. Bruce C. Murray, director of the Jet Propulsion Laboratory, comments on the mission.

  2. Rotation of the planet mercury.

    Science.gov (United States)

    Jefferys, W H

    1966-04-08

    The equations of motion for the rotation of Mercury are solved for the general case by an asymptotic expansion. The findings of Liu and O'Keefe, obtained by numerical integration of a special case, that it is possible for Mercury's rotation to be locked into a 2:3 resonance with its revolution, are confirmed in detail. The general solution has further applications.

  3. 49 CFR 173.164 - Mercury (metallic and articles containing mercury).

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Mercury (metallic and articles containing mercury... Than Class 1 and Class 7 § 173.164 Mercury (metallic and articles containing mercury). (a) For transportation by aircraft, mercury must be packaged in packagings which meet the requirements of part 178 of...

  4. Molecular modelling of zinc sulphide nanoparticles stabilized by cetyltrimethylammonium bromide

    Directory of Open Access Journals (Sweden)

    Kovář Petr

    2014-01-01

    Full Text Available ZnS nanoparticles stabilized by cetyltrimethylammonium bromide (CTAB were modelled in the Materials Studio environment. Four types of models with different distances between ZnS nanoparticles and different amounts of CTA cations without water and in water environment were built and characterized by calculated sublimation energies. The results of molecular modelling without water showed that the most favourable model consisted of two ZnS nanoparticles with a distance of 8-9 nm separated without immersing of CTAs. On the contrary, the most favourable model in water environment was composed of ZnS nanoparticles that nearly touched each other. CTA cations exhibited tendency to be located on the ZnS surface forming sparse covers. Size distributions of ZnS-CTA particles obtained by TEM measurements well agreed with molecular modelling results.

  5. Irradiation as an alternative to methyl bromide: the Australian situation

    International Nuclear Information System (INIS)

    Heather, N.W.

    1999-01-01

    International agreement to phase out the fumigant Methyl bromide (MeBr) will have serious implications for pest and disease control in Australia, particularly grain pest control, quarantine usage on fresh horticultural produce and control of soil pathogens or nematodes. Irradiation is a practical alternative but is not currently approved for use in Australia. Other options are available but none of the viable methods except irradiation have the short application time needed for treatment of grams found to be infested during loading at export. This usage is vital, as Australian grain is exported at very high standards of freedom from insects, assured by Government regulatory requirements. Irradiation is contrasted against other alternatives including heat and cold, especially for fresh horticultural produce. (author)

  6. Location of Bromide Ions in Tetragonal Lysozyme Crystals

    Science.gov (United States)

    Lim, Kap; Nadarajah, Arunan; Forsythe, Elizabeth L.; Pusey, Marc L.

    1998-01-01

    Anions have been shown to play a dominant role in the crystallization of chicken egg white lysozyme from salt solutions. Previous studies employing X-ray crystallography had found one chloride ion binding site in the tetragonal crystal form of the protein and four nitrate ion binding sites in the monoclinic form. In this study the anion positions in the tetragonal form were determined from the difference Fourier map obtained from lysozyme crystal grown in bromide and chloride solutions. Five possible anion binding sites were found in this manner. Some of these sites were in pockets containing basic residues while others were near neutral, but polar, residues. The sole chloride ion binding site found in previous studies was confirmed, while four of these sites corresponded to four binding sites found for nitrate ions in monoclinic crystals. The study suggests that most of the anion binding sites in lysozyme remain unchanged, even when different anions and different crystal forms of lysozyme are employed.

  7. Mercury concentration in bivalve molluscs

    Directory of Open Access Journals (Sweden)

    Szkoda Józef

    2015-09-01

    Full Text Available A total of 85 mussel samples of eight species were examined. Analysis of mercury in the freeze-dried samples was carried out by atomic absorption spectrometry method using direct mercury analyser AMA 254. The analytical procedure for determination of mercury was covered by the quality assurance programme of research and participation in national and international proficiency tests. Concentrations of total mercury in all investigated samples were found to be generally low, in the range of 0.033-0.577 mg/kg of dry weight and of 0.003-0.045 mg/kg of wet weight. The results indicate that obtained levels of mercury in bivalve molluscs are not likely to pose a risk to the health of consumers.

  8. Mercury: Beethoven Quadrangle, H-7

    Science.gov (United States)

    2000-01-01

    Mercury: Computer Photomosaic of the Beethoven Quadrangle, H-7 The Beethoven Quadrangle, named for the 19th century classical German composer, lies in Mercury's Equatorial Mercator located between longitude 740 to 1440. The Mariner 10 spacecraft imaged the region during its initial flyby of the planet. The Image Processing Lab at NASA's Jet Propulsion Laboratory produced this photomosaic using computer software and techniques developed for use in processing planetary data. The images used to construct the Beethoven Quadrangle were taken as Mariner 10 flew passed Mercury. The Mariner 10 spacecraft was launched in 1974. The spacecraft took images of Venus in February 1974 on the way to three encounters with Mercury in March and September 1974 and March 1975. The spacecraft took more than 7,000 images of Mercury, Venus, the Earth and the Moon during its mission. The Mariner 10 Mission was managed by the Jet Propulsion Laboratory for NASA's Office of Space Science in Washington, D.C.

  9. Comparative mobility of sulfonamides and bromide tracer in three soils

    Science.gov (United States)

    Kurwadkar, S.T.; Adams, C.D.; Meyer, M.T.; Kolpin, D.W.

    2011-01-01

    In animal agriculture, sulfonamides are one of the routinely used groups of antimicrobials for therapeutic and sub-therapeutic purposes. It is observed that, the animals when administered the antimicrobials, often do not completely metabolize them; and excrete the partially metabolized forms into the environment. Due to the continued use of antimicrobials and disposal of untreated waste, widespread occurrence of partially metabolized antimicrobials in aquatic and terrestrial environments has been reported in various scientific journals. In this research, the mobility of two sulfonamides - sulfamethazine (SMN), sulfathiazole (STZ) and a conservative bromide tracer was investigated in three soils collected from regions in the United States with large number of concentrated animal-feed operations. Results of a series of column studies indicate that the mobility of these two sulfonamides was dependent on pH, soil charge density, and contact time. At low pH and high charge density, substantial retention of sulfonamides was observed in all three soils investigated, due to the increased fraction of cationic and neutral forms of the sulfonamides. Conversely, enhanced mobility was observed at high pH, where the sulfonamides are predominantly in the anionic form. The results indicate that when both SMN and STZ are predominantly in anionic forms, their mobility approximates the mobility of a conservative bromide tracer. This observation is consistent for the mobility of both SMN and STZ individually, and also in the presence of several other antimicrobials in all three soils investigated. Higher contact time indicates lower mobility due to increased interaction with soil material. ?? 2011.

  10. 75 FR 41177 - Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications...

    Science.gov (United States)

    2010-07-15

    ... can be obtained in the following ways: 1. PDF format and Microsoft Excel at EPA's Web site: http://www... EPA to exempt the production and import of methyl bromide from the phaseout for critical uses, to the...? EPA regulations at 40 CFR 82.4 prohibit the production and import of methyl bromide in excess of the...

  11. Pancreatitis associated with potassium bromide/phenobarbital combination therapy in epileptic dogs.

    OpenAIRE

    Gaskill, C L; Cribb, A E

    2000-01-01

    In a retrospective study, at least 10% of dogs receiving potassium bromide/phenobarbital combination therapy, compared with 0.3% of dogs receiving phenobarbital monotherapy, had probable pancreatitis. Pancreatitis may be a more frequent and more serious adverse effect of potassium bromide/phenobarbital combination therapy than has been reported previously.

  12. Pancreatitis associated with potassium bromide/phenobarbital combination therapy in epileptic dogs.

    Science.gov (United States)

    Gaskill, C L; Cribb, A E

    2000-01-01

    In a retrospective study, at least 10% of dogs receiving potassium bromide/phenobarbital combination therapy, compared with 0.3% of dogs receiving phenobarbital monotherapy, had probable pancreatitis. Pancreatitis may be a more frequent and more serious adverse effect of potassium bromide/phenobarbital combination therapy than has been reported previously. PMID:10907578

  13. Destruction of methyl bromide sorbed to activated carbon by thiosulfate and electrolysis

    Science.gov (United States)

    Methyl bromide is widely used as a fumigant for post-harvest and quarantine uses at port facilities due to the low treatment times required, but it is vented to the atmosphere after its use. Due to the potential contributions of methyl bromide to stratospheric ozone depletion, technologies for the c...

  14. Copper-catalysed N-arylation of arylsulfonamides with aryl bromides ...

    Indian Academy of Sciences (India)

    An efficient synthesis of -arylsulfonamides with a variety of aryl bromides, aryl iodides and heteroaryl bromides using KF/Al2O3 as a suitable base, CuI as an inexpensive catalyst and ,'-dimethylethylenediamine (,'-DMEDA) as an effective ligand is described.

  15. A study of bromide in the Mandovi-Zuari river system of Goa

    Digital Repository Service at National Institute of Oceanography (India)

    DeSouza, F.P.; Dalal, V.N.K.

    concentrations were computed. The variation of bromide with chlorinity was linear indicating the purely conservative character of bromide and its seawater origin. Seawater ranged between 1 and 3% in monsoon, 76 and 91% in post-monsoon and 92 and 97% in pre...

  16. Human Exposure and Health Effects of Inorganic and Elemental Mercury

    OpenAIRE

    Park, Jung-Duck; Zheng, Wei

    2012-01-01

    Mercury is a toxic and non-essential metal in the human body. Mercury is ubiquitously distributed in the environment, present in natural products, and exists extensively in items encountered in daily life. There are three forms of mercury, i.e., elemental (or metallic) mercury, inorganic mercury compounds, and organic mercury compounds. This review examines the toxicity of elemental mercury and inorganic mercury compounds. Inorganic mercury compounds are water soluble with a bioavailability o...

  17. Methods for dispensing mercury into devices

    Science.gov (United States)

    Grossman, Mark W.; George, William A.

    1987-04-28

    A process for dispensing mercury into devices which requires mercury. Mercury is first electrolytically separated from either HgO or Hg.sub.2 Cl.sub.2 and plated onto a cathode wire. The cathode wire is then placed into a device requiring mercury.

  18. 21 CFR 872.3700 - Dental mercury.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dental mercury. 872.3700 Section 872.3700 Food and... DENTAL DEVICES Prosthetic Devices § 872.3700 Dental mercury. (a) Identification. Dental mercury is a device composed of mercury intended for use as a component of amalgam alloy in the restoration of a...

  19. Fluorescent sensor for mercury

    Science.gov (United States)

    Wang, Zidong [Urbana, IL; Lee, Jung Heon [Evanston, IL; Lu, Yi [Champaign, IL

    2011-11-22

    The present invention provides a sensor for detecting mercury, comprising: a first polynucleotide, comprising a first region, and a second region, a second polynucleotide, a third polynucleotide, a fluorophore, and a quencher, wherein the third polynucleotide is optionally linked to the second region; the fluorophore is linked to the first polynucleotide and the quencher is linked to the second polynucleotide, or the fluorophore is linked to the second polynucleotide and the quencher is linked to the first polynucleotide; the first region and the second region hybridize to the second polynucleotide; and the second region binds to the third polynucleotide in the presence of Hg.sup.2+ ions.

  20. Increased mercury emissions from modern dental amalgams

    OpenAIRE

    Bengtsson, Ulf G.; Hylander, Lars D.

    2017-01-01

    All types of dental amalgams contain mercury, which partly is emitted as mercury vapor. All types of dental amalgams corrode after being placed in the oral cavity. Modern high copper amalgams exhibit two new traits of increased instability. Firstly, when subjected to wear/polishing, droplets rich in mercury are formed on the surface, showing that mercury is not being strongly bonded to the base or alloy metals. Secondly, high copper amalgams emit substantially larger amounts of mercury vapor ...

  1. Mercury toxicity and neurodegenerative effects.

    Science.gov (United States)

    Carocci, Alessia; Rovito, Nicola; Sinicropi, Maria Stefania; Genchi, Giuseppe

    2014-01-01

    Mercury is among the most toxic heavy metals and has no known physiological role in humans. Three forms of mercury exist: elemental, inorganic and organic. Mercury has been used by man since ancient times. Among the earliest were the Chinese and Romans, who employed cinnabar (mercury sulfide) as a red dye in ink (Clarkson et al. 2007). Mercury has also been used to purify gold and silver minerals by forming amalgams. This is a hazardous practice, but is still widespread in Brazil's Amazon basin, in Laos and in Venezuela, where tens of thousands of miners are engaged in local mining activities to find and purify gold or silver. Mercury compounds were long used to treat syphilis and the element is still used as an antiseptic,as a medicinal preservative and as a fungicide. Dental amalgams, which contain about 50% mercury, have been used to repair dental caries in the U.S. since 1856.Mercury still exists in many common household products around the world.Examples are: thermometers, barometers, batteries, and light bulbs (Swain et al.2007). In small amounts, some organo mercury-compounds (e.g., ethylmercury tiosalicylate(thimerosal) and phenylmercury nitrate) are used as preservatives in some medicines and vaccines (Ballet al. 2001).Each mercury form has its own toxicity profile. Exposure to Hg0 vapor and MeHg produce symptoms in CNS, whereas, the kidney is the target organ when exposures to the mono- and di-valent salts of mercury (Hg+ and Hg++, respectively)occur. Chronic exposure to inorganic mercury produces stomatitis, erethism and tremors. Chronic MeHg exposure induced symptoms similar to those observed in ALS, such as the early onset of hind limb weakness (Johnson and Atchison 2009).Among the organic mercury compounds, MeHg is the most biologically available and toxic (Scheuhammer et a!. 2007). MeHg is neurotoxic, reaching high levels of accumulation in the CNS; it can impair physiological function by disrupting endocrine glands (Tan et a!. 2009).The most

  2. Mercury kinetics in marine zooplankton

    International Nuclear Information System (INIS)

    Fowler, S.W.; Heyraud, M.; LaRosa, J.

    1976-01-01

    Mercury, like many other heavy metals, is potentially available to marine animals by uptake directly from water and/or through the organisms food. Furthermore, bioavailability, assimilation and subsequent retention in biota may be affected by the chemical species of the element in sea water. While mercury is known to exist in the inorganic form in sea water, recent work has indicated that, in certain coastal areas, a good portion of the total mercury appears to be organically bound; however, the exact chemical nature of the organic fraction has yet to be determined. Methyl mercury may be one constituent of the natural organically bound fraction since microbial mechanisms for in situ methylation of mercury have been demonstrated in the aquatic environment. Despite the fact that naturally produced methyl mercury probably comprises only a small fraction of an aquatic ecosystem, the well-documented toxic effects of this organo-mercurial, caused by man-made introductions into marine food chains, make it an important compound to study

  3. Atmospheric mercury footprints of nations.

    Science.gov (United States)

    Liang, Sai; Wang, Yafei; Cinnirella, Sergio; Pirrone, Nicola

    2015-03-17

    The Minamata Convention was established to protect humans and the natural environment from the adverse effects of mercury emissions. A cogent assessment of mercury emissions is required to help implement the Minamata Convention. Here, we use an environmentally extended multi-regional input-output model to calculate atmospheric mercury footprints of nations based on upstream production (meaning direct emissions from the production activities of a nation), downstream production (meaning both direct and indirect emissions caused by the production activities of a nation), and consumption (meaning both direct and indirect emissions caused by final consumption of goods and services in a nation). Results show that nations function differently within global supply chains. Developed nations usually have larger consumption-based emissions than up- and downstream production-based emissions. India, South Korea, and Taiwan have larger downstream production-based emissions than their upstream production- and consumption-based emissions. Developed nations (e.g., United States, Japan, and Germany) are in part responsible for mercury emissions of developing nations (e.g., China, India, and Indonesia). Our findings indicate that global mercury abatement should focus on multiple stages of global supply chains. We propose three initiatives for global mercury abatement, comprising the establishment of mercury control technologies of upstream producers, productivity improvement of downstream producers, and behavior optimization of final consumers.

  4. Method for removal and stabilization of mercury in mercury-containing gas streams

    Science.gov (United States)

    Broderick, Thomas E.

    2005-09-13

    The present invention is directed to a process and apparatus for removing and stabilizing mercury from mercury-containing gas streams. A gas stream containing vapor phase elemental and/or speciated mercury is contacted with reagent, such as an oxygen-containing oxidant, in a liquid environment to form a mercury-containing precipitate. The mercury-containing precipitate is kept or placed in solution and reacts with one or more additional reagents to form a solid, stable mercury-containing compound.

  5. Exploring Mercury: The Iron Planet

    OpenAIRE

    Stevenson, David J.

    2004-01-01

    Planet Mercury is both difficult to observe and difficult to reach by spacecraft. Just one spacecraft, Mariner 10, flew by the planet 30 years ago. An upcoming NASA mission, MESSENGER, will be launched this year and will go into orbit around Mercury at the end of this decade. A European mission is planned for the following decade. It's worth going there because Mercury is a strange body and the history of planetary exploration has taught us that strangeness gives us insight into planetary ori...

  6. MESSENGER'S First Flyby of Mercury

    Science.gov (United States)

    Slavin, James A.

    2008-01-01

    The MESSENGER mission to Mercury offers our first opportunity to explore this planet's miniature magnetosphere since Mariner 10's brief fly-bys in 1974-5. The magnetosphere of Mercury is the smallest in the solar system with its magnetic field typically standing off the solar wind only - 1000 to 2000 km above the surface. An overview of the MESSENGER mission and its January 14th close flyby of Mercury will be provided. Primary science objectives and the science instrumentation will be described. Initial results from MESSENGER'S first flyby on January 14th, 2008 will be discussed with an emphasis on the magnetic field and charged particle measurements.

  7. Distribution and retention of organic and inorganic mercury in methyl mercury-treated neonatal rats

    International Nuclear Information System (INIS)

    Thomas, D.J.; Fisher, H.L.; Sumler, M.R.; Hall, L.L.; Mushak, P.

    1988-01-01

    Seven-day-old Long Evans rats received one mumol of 203 Hg-labeled methyl mercury/kg sc and whole body retention and tissue distribution of organic and inorganic mercury were examined for 32 days postdosing. Neonates cleared mercury slowly until 10 days postdosing when the clearance rate abruptly increased. During the interval when whole body clearance of mercury was extremely slow, methyl mercury was metabolized to inorganic mercury. Peak concentration of mercury in kidney occurred at 2 days postdosing. At 32 days postdosing, 8% of mercury in kidney was in an organic from. Liver mercury concentration peaked at 2 days postdosing and organic mercury accounted for 38% at 32 days postdosing. Brain concentrations of mercury peaked at 2 days postdosing. At 10 days postdosing, organic mercury accounted for 86% of the brain mercury burden, and, at 32 days postdosing, for 60%. The percentage of mercury body burden in pelt rose from 30 to 70% between 1 and 10 days postdosing. At 32 days postdosing pelt contained 85% of the body burden of mercury. At all time points, about 95% of mercury in pelt was in an organic form. Compartmental analysis of these data permitted development of a model to describe the distribution and excretion of organic and inorganic mercury in methyl mercury-treated neonatal rats

  8. Elimination of mercury in health care facilities.

    Science.gov (United States)

    2000-03-01

    Mercury is a persistent, bioaccumulative toxin that has been linked to numerous health effects in humans and wildlife. It is a potent neurotoxin that may also harm the brain, kidneys, and lungs. Unborn children and young infants are at particular risk for brain damage from mercury exposure. Hospitals' use of mercury in chemical solutions, thermometers, blood pressure gauges, batteries, and fluorescent lamps makes these facilities large contributors to the overall emission of mercury into the environment. Most hospitals recognize the dangers of mercury. In a recent survey, four out of five hospitals stated that they have policies in place to eliminate the use of mercury-containing products. Sixty-two percent of them require vendors to disclose the presence of mercury in chemicals that the hospitals purchase. Only 12 percent distribute mercury-containing thermometers to new parents. Ninety-two percent teach their employees about the health and environmental effects of mercury, and 46 percent teach all employees how to clean up mercury spills. However, the same study showed that many hospitals have not implemented their policies. Forty-two percent were not aware whether they still purchased items containing mercury. In addition, 49 percent still purchase mercury thermometers, 44 percent purchase mercury gastrointestinal diagnostic equipment, and 64 percent still purchase mercury lab thermometers.

  9. Mercury pollution: a transdisciplinary treatment

    National Research Council Canada - National Science Library

    Zuber, Sharon L; Newman, Michael C

    2012-01-01

    .... Also included are smaller case studies, such as the Minamata tragedy, fish consumption, and international treaties"-- "Mercury is the gravest chemical pollutant problem of our time, and this is...

  10. Origin and composition of Mercury

    International Nuclear Information System (INIS)

    Lewis, J.S.

    1988-01-01

    The predictions of the expected range of composition of Mercury at the time of its formation made on the basis of a suite of condensation-accretion models of Mercury spanning a range of condensation temperature and accretion sampling functions appropriate to Mercury are examined. It is concluded that these compositonal models can, if modified to take into account the nonselective loss of most of the silicate component of the planet during accretion, provide compositional predictions for the Weidenschilling (1978, 1980) mechanism for the accretion of a metal-rich Mercury. The silicate portion would, in this case, contain 3.6 to 4.5 percent alumina, roughly 1 percent of alkali oxides, and between 0.5 and 6 percent FeO

  11. Gold micro- and nano-particles for surface enhanced vibrational spectroscopy of pyridostigmine bromide

    DEFF Research Database (Denmark)

    Dolgov, Leonid; Fesenko, Olena; Kavelin, Vladyslav

    2017-01-01

    Triangular gold microprisms and spherical silica nanoparticles with attached gold nano-islands were examined as an active nanostructures for the surface enhanced Raman and infrared spectroscopy. These particles were probed for the detection of pyridostigmine bromide as a safe analog of military...... compound sarin. Raman and infrared spectral bands of the pyridostigmine bromide were measured. Detailed correlation of obtained spectral bands with specific vibrations in pyridostigmine bromide was done. Silica nanoparticles with attached gold nano-islands showed more essential enhancement of the Raman...

  12. Evaluation of Alkali Bromide Salts for Potential Pyrochemical Applications

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat K. Tripathy; Steven D. Herrmann; Guy L. Fredrickson; Tedd E. Lister; Toni Y. Gutknecht

    2013-10-01

    Transient techniques were employed to study the electrochemical behavior, reduction mechanism and transport properties of REBr3 (RE - La, Nd and Gd) in pure LiBr, LiBr-KBr (eutectic) and LiBr-KBr-CsBr (eutectic) melts. Gd(III) showed a reversible single step soluble-insoluble exchange phenomenon in LiBr melt at 973K. Although La (III), Nd(III) and Gd(III) ions showed reversible behavior in eutectic LiBr-KBr melts, these ions showed a combination of temperature dependent reversible and pseudo-reversible behavior. While both La(III) and Gd(III) showed one step reduction, the reduction of Nd(III) was observed to be a two step process. La metal could be electrodeposited from the ternary electrolyte at a temperature of 673K. Various electrochemical measurements suggest that both binary and ternary bromide melts can potentially be used to electrodeposit high purity RE metals at comparatively lower operating temperatures.

  13. Agricultural soil fumigation as a source of atmospheric methyl bromide.

    Science.gov (United States)

    Yagi, K; Williams, J; Wang, N Y; Cicerone, R J

    1993-09-15

    Methyl bromide (MeBr) is used increasingly as a biocidal fumigant, primarily in agricultural soils prior to planting of crops. This usage carries potential for stratospheric ozone reduction due to Br atom catalysis, depending on how much MeBr escapes from fumigated soils to the atmosphere and on details of atmospheric chemical reactions. We present direct field measurements of MeBr escape; 87% of the applied MeBr was emitted within 7 days after a commercial fumigation. Covering the field with plastic sheets retarded MeBr escape somewhat but first-day losses were still 40%; thicker sections of sheets were relatively more effective than thin sections. We also measured gaseous MeBr concentrations versus depth in the soil column; these profiles display diffusion-like evolution. In soil, MeBr is partitioned among gas, liquid, and adsorbed solid phases. Calculated soil inventories agreed only roughly with applied amounts, probably due to nonequilibrium partitioning (during the first 30 min) and to uncertainties in partitioning coefficients. Fumigated fields may release less MeBr if they are covered by more gas-tight plastic films, if injection techniques are improved and injection is deeper, and if soil moistures, organic amounts, and densities are greater than in the soil studied here.

  14. Improved spectrometric characteristics of thallium bromide nuclear radiation detectors

    CERN Document Server

    Hitomi, K; Shoji, T; Suehiro, T; Hiratate, Y

    1999-01-01

    Thallium bromide (TlBr) is a compound semiconductor with a high atomic number and wide band gap. In this study, nuclear radiation detectors have been fabricated from the TlBr crystals. The TlBr crystals were grown by the horizontal travelling molten zone (TMZ) method using the materials purified by many pass zone refining. The crystals were characterized by measuring the resistivity, the mobility-lifetime (mu tau) product and the energy required to create an electron-hole pair (the epsilon value). Improved energy resolution has been obtained by the TlBr radiation detectors. At room temperature the full-width at half-maximum (FWHM) for the 59.5, 122 and 662 keV gamma-ray photo peak obtained from the detectors were 3.3, 8.8 and 29.5 keV, respectively. By comparing the saturated peak position of the TlBr detector with that of the CdTe detector, the epsilon value has been estimated to be about 5.85 eV for the TlBr crystal.

  15. Advanced crystal growth techniques for thallium bromide semiconductor radiation detectors

    Science.gov (United States)

    Datta, Amlan; Becla, Piotr; Guguschev, Christo; Motakef, Shariar

    2018-02-01

    Thallium Bromide (TlBr) is a promising room-temperature radiation detector candidate with excellent charge transport properties. Currently, Travelling Molten Zone (TMZ) technique is widely used for growth of semiconductor-grade TlBr crystals. However, there are several challenges associated with this type of crystal growth process including lower yield, high thermal stress, and low crystal uniformity. To overcome these shortcomings of the current technique, several different crystal growth techniques have been implemented in this study. These include: Vertical Bridgman (VB), Physical Vapor Transport (PVT), Edge-defined Film-fed Growth (EFG), and Czochralski Growth (Cz). Techniques based on melt pulling (EFG and Cz) were demonstrated for the first time for semiconductor grade TlBr material. The viability of each process along with the associated challenges for TlBr growth has been discussed. The purity of the TlBr crystals along with its crystalline and electronic properties were analyzed and correlated with the growth techniques. Uncorrected 662 keV energy resolutions around 2% were obtained from 5 mm x 5 mm x 10 mm TlBr devices with virtual Frisch-grid configuration.

  16. Accommodation coefficient of HOBr on deliquescent sodium bromide aerosol particles

    Directory of Open Access Journals (Sweden)

    M. Wachsmuth

    2002-01-01

    Full Text Available Uptake of HOBr on sea salt aerosol, sea salt brine or ice is believed to be a key process providing a source of photolabile bromine (Br2 and sustaining ozone depletion cycles in the Arctic troposphere. In the present study, uptake of HOBr on sodium bromide (NaBr aerosol particles was investigated at an extremely low HOBr concentration of 300 cm-3 using the short-lived radioactive isotopes 83-86Br. Under these conditions, at maximum one HOBr molecule was taken up per particle. The rate of uptake was clearly limited by the mass accommodation coefficient, which was calculated to be 0.6 ± 0.2. This value is a factor of 10 larger than estimates used in earlier models. The atmospheric implications are discussed using the box model "MOCCA'', showing that the increase of the accommodation coefficient of HOBr by a factor of 10 only slightly affects net ozone loss, but significantly increases chlorine release.

  17. 4-Bromophenacyl bromide specifically inhibits rhoptry secretion during Toxoplasma invasion.

    Directory of Open Access Journals (Sweden)

    Sandeep Ravindran

    2009-12-01

    Full Text Available Toxoplasma gondii is a eukaryotic parasite of the phylum Apicomplexa that is able to infect a wide variety of host cells. During its active invasion process it secretes proteins from discrete secretory organelles: the micronemes, rhoptries and dense granules. Although a number of rhoptry proteins have been shown to be involved in important interactions with the host cell, very little is known about the mechanism of secretion of any Toxoplasma protein into the host cell. We used a chemical inhibitor of phospholipase A2s, 4-bromophenacyl bromide (4-BPB, to look at the role of such lipases in the secretion of Toxoplasma proteins. We found that 4-BPB was a potent inhibitor of rhoptry secretion in Toxoplasma invasion. This drug specifically blocked rhoptry secretion but not microneme secretion, thus effectively showing that the two processes can be de-coupled. It affected parasite motility and invasion, but not attachment or egress. Using propargyl- or azido-derivatives of the drug (so-called click chemistry derivatives and a series of 4-BPB-resistant mutants, we found that the drug has a very large number of target proteins in the parasite that are involved in at least two key steps: invasion and intracellular growth. This potent compound, the modified "click-chemistry" forms of it, and the resistant mutants should serve as useful tools to further study the processes of Toxoplasma early invasion, in general, and rhoptry secretion, in particular.

  18. IPRATROPIUM BROMIDE FOR ACUTE ASTHMA IN CHILDREN: A RETROSPECTIVE TRIAL.

    Science.gov (United States)

    Nomura, Osamu; Morikawa, Yoshihiko; Hagiwara, Yusuke; Ihara, Takateru; Inoue, Nobuaki; Sakakibara, Hiroshi; Akasawa, Akira

    Inhaled anticholinergics such as ipratropium bromide (IB), when administered with β2-agonists, are effective in reducing hospital admissions of children presenting to the emergency department with moderate to severe asthma. However, treatment of acute asthma with IB is still uncommon in Japan. The aim of this study was to investigate the effectiveness and safety of IB for the treatment of pediatric acute asthma. We conducted a retrospective study to compare the admission rate of patients who received IB with those who did not. Patients aged 4 years or older with a history of moderate to severe attacks were included. For analysis, propensity score matching was used to adjust the confounding factors related to IB use. Patients received IB by metered-dose inhaler (40μg per dose) with a spacer three times at 20-min intervals. Among 175 patients included in the analysis, 102 patients were treated with IB (IB group) and 73 patients were treated without IB (Non-IB group). A propensity score matching analysis extracted 63 patients from each group. There was no statistical difference between the two groups in terms of admission rate (IB group 12.7% vs Non-IB group 9.5%; p=0.78). One patient (1.0%) treated with IB experienced dryness of the mouth, which resolved spontaneously. The admission rate did not decline with IB use. Several confounding factors could have influenced and limited our results. A prospective study is needed to investigate the effectiveness of IB in Japan.

  19. Locations of Bromide Ions in Tetragonal Lysozyme Crystals

    Science.gov (United States)

    Lim, Kap; Nadarajah, Arunan; Forsythe, Elizabeth L.; Pusey, Marc L.

    1998-01-01

    Anions have been shown to play a dominant role in the crystallization of chicken egg-white lysozyme from salt solutions. Previous studies employing X-ray crystallography have found one chloride ion binding site in the tetragonal crystal form of the protein and four nitrate ion binding sites in the monoclinic form. In this study the anion positions in the tetragonal form were determined from the difference Fourier map obtained from lysozyme crystals grown in bromide and chloride solutions. Five possible anion-binding sites were found in this manner. Some of these sites were in pockets containing basic residues while others were near neutral, but polar, residues. The sole chloride ion binding site found in previous studies was confirmed, while four further sites were found which corresponded to the four binding sites found for nitrate ions in monoclinic crystals. The study suggests that most of the anion-binding sites in lysozyme remain unchanged even when different anions and different crystal forms of lysozyme are employed.

  20. Localized surface plasmon resonance mercury detection system and methods

    Science.gov (United States)

    James, Jay; Lucas, Donald; Crosby, Jeffrey Scott; Koshland, Catherine P.

    2016-03-22

    A mercury detection system that includes a flow cell having a mercury sensor, a light source and a light detector is provided. The mercury sensor includes a transparent substrate and a submonolayer of mercury absorbing nanoparticles, e.g., gold nanoparticles, on a surface of the substrate. Methods of determining whether mercury is present in a sample using the mercury sensors are also provided. The subject mercury detection systems and methods find use in a variety of different applications, including mercury detecting applications.

  1. Mercury Toolset for Spatiotemporal Metadata

    Science.gov (United States)

    Devarakonda, Ranjeet; Palanisamy, Giri; Green, James; Wilson, Bruce; Rhyne, B. Timothy; Lindsley, Chris

    2010-06-01

    Mercury (http://mercury.ornl.gov) is a set of tools for federated harvesting, searching, and retrieving metadata, particularly spatiotemporal metadata. Version 3.0 of the Mercury toolset provides orders of magnitude improvements in search speed, support for additional metadata formats, integration with Google Maps for spatial queries, facetted type search, support for RSS (Really Simple Syndication) delivery of search results, and enhanced customization to meet the needs of the multiple projects that use Mercury. It provides a single portal to very quickly search for data and information contained in disparate data management systems, each of which may use different metadata formats. Mercury harvests metadata and key data from contributing project servers distributed around the world and builds a centralized index. The search interfaces then allow the users to perform a variety of fielded, spatial, and temporal searches across these metadata sources. This centralized repository of metadata with distributed data sources provides extremely fast search results to the user, while allowing data providers to advertise the availability of their data and maintain complete control and ownership of that data. Mercury periodically (typically daily)harvests metadata sources through a collection of interfaces and re-indexes these metadata to provide extremely rapid search capabilities, even over collections with tens of millions of metadata records. A number of both graphical and application interfaces have been constructed within Mercury, to enable both human users and other computer programs to perform queries. Mercury was also designed to support multiple different projects, so that the particular fields that can be queried and used with search filters are easy to configure for each different project.

  2. Mercury Toolset for Spatiotemporal Metadata

    Science.gov (United States)

    Wilson, Bruce E.; Palanisamy, Giri; Devarakonda, Ranjeet; Rhyne, B. Timothy; Lindsley, Chris; Green, James

    2010-01-01

    Mercury (http://mercury.ornl.gov) is a set of tools for federated harvesting, searching, and retrieving metadata, particularly spatiotemporal metadata. Version 3.0 of the Mercury toolset provides orders of magnitude improvements in search speed, support for additional metadata formats, integration with Google Maps for spatial queries, facetted type search, support for RSS (Really Simple Syndication) delivery of search results, and enhanced customization to meet the needs of the multiple projects that use Mercury. It provides a single portal to very quickly search for data and information contained in disparate data management systems, each of which may use different metadata formats. Mercury harvests metadata and key data from contributing project servers distributed around the world and builds a centralized index. The search interfaces then allow the users to perform a variety of fielded, spatial, and temporal searches across these metadata sources. This centralized repository of metadata with distributed data sources provides extremely fast search results to the user, while allowing data providers to advertise the availability of their data and maintain complete control and ownership of that data. Mercury periodically (typically daily) harvests metadata sources through a collection of interfaces and re-indexes these metadata to provide extremely rapid search capabilities, even over collections with tens of millions of metadata records. A number of both graphical and application interfaces have been constructed within Mercury, to enable both human users and other computer programs to perform queries. Mercury was also designed to support multiple different projects, so that the particular fields that can be queried and used with search filters are easy to configure for each different project.

  3. Zn Mediated Regioselective Barbier Reaction of Propargylic Bromides in THF/aq. NH4Cl Solution

    Directory of Open Access Journals (Sweden)

    Uno Mäeorg

    2001-11-01

    Full Text Available The reaction of substituted and unsubstituted propargylic bromides with butanal in presence of zinc power in THF/saturated aqueous NH4Cl solution gave corresponding allenic and propargylic alcohols with high selectivity.

  4. Zn Mediated Regioselective Barbier Reaction of Propargylic Bromides in THF/aq. NH4Cl Solution

    OpenAIRE

    Jõgi, Artur; Mäeorg, Uno

    2001-01-01

    The reaction of substituted and unsubstituted propargylic bromides with butanal in presence of zinc power in THF/saturated aqueous NH4Cl solution gave corresponding allenic and propargylic alcohols with high selectivity.

  5. Neuropsychological Functioning in Gulf War Veterans Exposed to Pesticides and Pyridostigmine Bromide

    National Research Council Canada - National Science Library

    Krengel, Maxine

    2006-01-01

    .... Suspected causes for these health complaints continue to be investigated and include additive and/or synergystic effects of the varying combinations of exposures to pesticides, pyridostigmine bromide (PB...

  6. Neuropsychological Functioning in Gulf War Veterans Exposed to Pesticides and Pyridostigmine Bromide

    National Research Council Canada - National Science Library

    Krengel, Maxine H

    2005-01-01

    .... Suspected causes for these health complaints continue to be investigated and include additive and/or synergystic effects of the varying combinations of exposures to pesticides, pyridostigmine bromide (PB...

  7. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Treatment Longer than 8 Hours

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  8. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Treatment 8 Hours or Less

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  9. Phytoremediation of Ionic and Methyl Mercury Pollution

    Energy Technology Data Exchange (ETDEWEB)

    Meagher, Richard B.

    2005-06-01

    Phytoremediation is defined as the use of plants to extract, resist, detoxify, and/or sequester toxic environmental pollutants. The long-term goal of the proposed research is to develop and test highly productive, field-adapted plant species that have been engineered for the phytoremediation of mercury. A variety of different genes, which should enable plants to clean mercury polluted sites are being tested as tools for mercury phytoremediation, first in model laboratory plants and then in potential field species. Several of these genes have already been shown to enhance mercury phytoremediation. Mercury pollution is a serious, world-wide problem affecting the health of human and wildlife populations. Environmentally, the most serious mercury threat is the production of methylmercury (CH3Hg+) by native bacteria at mercury contaminated wetland sites. Methylmercury is inherently more toxic than metallic (Hg(0)) or ionic (Hg(II)) mercury, and because methylmercury is prolifically biomagnified up the food chain, it poses the most immediate danger to animal populations. We have successfully engineered two model plants, Arabidopsis and tobacco, to use the bacterial merB gene to convert methylmercury to less toxic ionic mercury and to use the bacterial merA gene to further detoxify ionic mercury to the least toxic form of mercury, metallic mercury. Plants expressing both MerA and MerB proteins detoxify methylmercury in two steps to the metallic form. These plants germinate, grow, and set seed at normal growth rates on levels of methylmercury or ionic mercury that are lethal to normal plants. Our newest efforts involve engineering plants with several additional bacterial and plant genes that allow for higher levels of mercury resistance and mercury hyperaccumulation. The potential for these plants to hyperaccumulate mercury was further advanced by developing constitutive, aboveground, and root-specific gene expression systems. Our current strategy is to engineer plants to

  10. Autometallographic tracing of mercury in frog liver

    International Nuclear Information System (INIS)

    Loumbourdis, N.S.; Danscher, G.

    2004-01-01

    The distribution of mercury in the liver of the frog Rana ridibunda with the autometallographic method was investigated. The mercury specific autometallographic (HgS/Se AMG ) technique is a sensitive histochemical approach for tracing mercury in tissues from mercury-exposed organisms. Mercury accumulates in vivo as mercury sulphur/mercury selenium nanocrystals that can be silver-enhanced. Thus, only a fraction of the Hg can be visualized. Six animals were exposed for one day and another group of six animals for 6 days in 1 ppm mercury (as HgCI 2 ) dissolved in fresh water. A third group of six animals, served as controls, were sacrificed the day of arrival at the laboratory. First, mercury appears in the blood plasma and erythrocytes. Next, mercury moves to hepatocytes and in the apical part of the cells, that facing bile canaliculi. In a next step, mercury appears in the endothelial and Kupffer cells. It seems likely that, the mercury of hepatocytes moves through bile canaliculi to the gut, most probably bound to glutathione and/or other similar ligands. Most probably, the endothelial and Kupffer cells comprise the first line of defense against metal toxicity. - Frogs can be good bioindicators of mercury

  11. Stabilized thallium bromide radiation detectors and methods of making the same

    Science.gov (United States)

    Leao, Cedric Rocha; Lordi, Vincenzo

    2015-11-24

    According to one embodiment, a crystal includes thallium bromide (TlBr), one or more positively charged dopants, and one or more negatively charged dopants. According to another embodiment, a system includes a monolithic crystal including thallium bromide (TlBr), one or more positively charged dopants, and one or more negatively charged dopants; and a detector configured to detect a signal response of the crystal.

  12. Tribromoisocyanuric acid/triphenylphosphine: a new system for conversion of alcohols into alkyl bromides

    International Nuclear Information System (INIS)

    Andrade, Vitor S.C. de; Mattos, Marcio C.S. de

    2014-01-01

    An efficient and facile method has been developed for the conversion of alcohols into alkyl bromides under neutral conditions using tribromoisocyanuric acid and triphenylphosphine (molar ratio 1.0:0.7:2.0, alcohol/tribromoisocyanuric acid/triphenylphosphine) in dichloromethane at room temperature. This method can be applied for the conversion of primary, secondary, benzilic and allylic alcohols, and their corresponding bromides are obtained in 67-82 % yield. Tertiary alcohols do not react under these conditions. (author)

  13. Tribromoisocyanuric acid/triphenylphosphine: a new system for conversion of alcohols into alkyl bromides

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Vitor S.C. de; Mattos, Marcio C.S. de, E-mail: mmattos@iq.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Instituto de Quimica. Departamento de Quimica Organica

    2014-05-15

    An efficient and facile method has been developed for the conversion of alcohols into alkyl bromides under neutral conditions using tribromoisocyanuric acid and triphenylphosphine (molar ratio 1.0:0.7:2.0, alcohol/tribromoisocyanuric acid/triphenylphosphine) in dichloromethane at room temperature. This method can be applied for the conversion of primary, secondary, benzilic and allylic alcohols, and their corresponding bromides are obtained in 67-82 % yield. Tertiary alcohols do not react under these conditions. (author)

  14. Mercury: Aspects of its ecology and environmental toxicity. [physiological effects of mercury compound contamination of environment

    Science.gov (United States)

    Siegel, S. M.

    1973-01-01

    A study was conducted to determine the effects of mercury pollution on the environment. The possible sources of mercury contamination in sea water are identified. The effects of mercury on food sources, as represented by swordfish, are analyzed. The physiological effects of varying concentrations of mercury are reported. Emphasis is placed on the situation existing in the Hawaiian Islands.

  15. Groundwater Modeling Of Mercury Pollution At A Former Mercury Cell Chlor Alkali Facility In Pavoldar, Kazakhstan

    Science.gov (United States)

    In Kazakhstan, there is a serious case of mercury pollution near the city of Pavlodar from an old mercury cell chlor-alkali plant. The soil, sediment, and water is severly contaminated with mercury and mercury compounds as a result of the industrial activity of this chemical pla...

  16. Fluorescence Decay Dynamics of Ethidium Bromide in Polymers

    International Nuclear Information System (INIS)

    Jee, Ah Young; Min Yung

    2010-01-01

    The fluorescence lifetimes of EB in five polymers covering LDPE, HDPE, PC, PS, and PAA were measured by picosecond time-correlated single photon counting. The lifetime change of EB has been previously described by hydrogen bonding ability. In this work, we have observed that the lifetime of EB depends strongly on the Young's modulus of medium. Thus, it is possible that the fluorescence decay dynamics of EB could be influenced by medium rigidity rather than hydrogen bonding ability in polymer. The medium influence on the fluorescence decay dynamics of ethidium bromide (EB) has been investigated in various environments. For example, Ohmstead and Kearns related the fluorescence lifetime of EB to the excited-state proton transfer process. In addition, they reported that the solvent viscosity plays a minor role in the excited state decay process of EB. Chirico et al. measured the fluorescence decay of EB as 1.7 ns in water and 6.5 ns in ethanol and concluded that hydrogen bonding ability is a key factor for the nonradiative relaxation. Pal et al. measured the fluorescence decay time of EB in acetone, acetonitrile, and their mixtures. They observed that the fluorescence decay processes were independent on the solvent polarity. These results show that the EB lifetime does not depend much on polarity or viscosity, but is mainly influenced by hydrogen bonding. Overall, EB is one of most widely used dyes for probing DNA. When EB is intercalated into the helical structure of DNA, a large increase in the fluorescence lifetime has been observed in comparison with water environment, and the fluorescence enhancement was attributed to the blocking of the excited-state proton transfer

  17. Stable room-temperature thallium bromide semiconductor radiation detectors

    Science.gov (United States)

    Datta, A.; Fiala, J.; Becla, P.; Motakef, Shariar

    2017-10-01

    Thallium bromide (TlBr) is a highly efficient ionic semiconductor with excellent radiation detection properties. However, at room temperature, TlBr devices polarize under an applied electric field. This phenomenon not only degrades the charge collection efficiency of the detectors but also promotes chemical reaction of the metal electrodes with bromine, resulting in an unstable electric field and premature failure of the device. This drawback has been crippling the TlBr semiconductor radiation detector technology over the past few decades. In this exhaustive study, this polarization phenomenon has been counteracted using innovative bias polarity switching schemes. Here the highly mobile Br- species, with an estimated electro-diffusion velocity of 10-8 cm/s, face opposing electro-migration forces during every polarity switch. This minimizes the device polarization and availability of Br- ions near the metal electrode. Our results indicate that it is possible to achieve longer device lifetimes spanning more than 17 000 h (five years of 8 × 7 operation) for planar and pixelated radiation detectors using this technique. On the other hand, at constant bias, 2500 h is the longest reported lifetime with most devices less than 1000 h. After testing several biasing switching schemes, it is concluded that the critical bias switching frequency at an applied bias of 1000 V/cm is about 17 μHz. Using this groundbreaking result, it will now be possible to deploy this highly efficient room temperature semiconductor material for field applications in homeland security, medical imaging, and physics research.

  18. The killing of African trypanosomes by ethidium bromide.

    Directory of Open Access Journals (Sweden)

    Arnab Roy Chowdhury

    2010-12-01

    Full Text Available Introduced in the 1950s, ethidium bromide (EB is still used as an anti-trypanosomal drug for African cattle although its mechanism of killing has been unclear and controversial. EB has long been known to cause loss of the mitochondrial genome, named kinetoplast DNA (kDNA, a giant network of interlocked minicircles and maxicircles. However, the existence of viable parasites lacking kDNA (dyskinetoplastic led many to think that kDNA loss could not be the mechanism of killing. When recent studies indicated that kDNA is indeed essential in bloodstream trypanosomes and that dyskinetoplastic cells survive only if they have a compensating mutation in the nuclear genome, we investigated the effect of EB on kDNA and its replication. We here report some remarkable effects of EB. Using EM and other techniques, we found that binding of EB to network minicircles is low, probably because of their association with proteins that prevent helix unwinding. In contrast, covalently-closed minicircles that had been released from the network for replication bind EB extensively, causing them, after isolation, to become highly supertwisted and to develop regions of left-handed Z-DNA (without EB, these circles are fully relaxed. In vivo, EB causes helix distortion of free minicircles, preventing replication initiation and resulting in kDNA loss and cell death. Unexpectedly, EB also kills dyskinetoplastic trypanosomes, lacking kDNA, by inhibiting nuclear replication. Since the effect on kDNA occurs at a >10-fold lower EB concentration than that on nuclear DNA, we conclude that minicircle replication initiation is likely EB's most vulnerable target, but the effect on nuclear replication may also contribute to cell killing.

  19. Stable room-temperature thallium bromide semiconductor radiation detectors

    Directory of Open Access Journals (Sweden)

    A. Datta

    2017-10-01

    Full Text Available Thallium bromide (TlBr is a highly efficient ionic semiconductor with excellent radiation detection properties. However, at room temperature, TlBr devices polarize under an applied electric field. This phenomenon not only degrades the charge collection efficiency of the detectors but also promotes chemical reaction of the metal electrodes with bromine, resulting in an unstable electric field and premature failure of the device. This drawback has been crippling the TlBr semiconductor radiation detector technology over the past few decades. In this exhaustive study, this polarization phenomenon has been counteracted using innovative bias polarity switching schemes. Here the highly mobile Br− species, with an estimated electro-diffusion velocity of 10−8 cm/s, face opposing electro-migration forces during every polarity switch. This minimizes the device polarization and availability of Br− ions near the metal electrode. Our results indicate that it is possible to achieve longer device lifetimes spanning more than 17 000 h (five years of 8 × 7 operation for planar and pixelated radiation detectors using this technique. On the other hand, at constant bias, 2500 h is the longest reported lifetime with most devices less than 1000 h. After testing several biasing switching schemes, it is concluded that the critical bias switching frequency at an applied bias of 1000 V/cm is about 17 μHz. Using this groundbreaking result, it will now be possible to deploy this highly efficient room temperature semiconductor material for field applications in homeland security, medical imaging, and physics research.

  20. Eudragit RS PO nanoparticles for sustained release of pyridostigmine bromide

    International Nuclear Information System (INIS)

    Hoobakht, Fatemeh; Ganji, Fariba; Vasheghani-Farahani, Ebrahim; Mousavi, Seyyed Mohammad

    2013-01-01

    Pyridostigmine bromide (PB) is an inhibitor of cholinesterase, which is used in the treatment of myasthenia gravis and administered for protection against exposure to toxic nerve agents. Tests were done to investigate prolonging the half-life of PB and improving its release behavior. PB was loaded in nanoparticles (NPs) of Eudragit RS PO (Eu-RS) prepared using the technique of quasi emulsion solvent diffusion. Variables of output power of the sonicator, bath temperature and mixing time, were chosen as the optimization factors to obtain the minimum sized NPs. In addition, emulsions were tested at different ratios of drug-to-polymer by dynamic light scattering to determine size and zeta potential of NPs. UV-spectroscopy was used to determine PB content of the NPs. Drug-loaded NPs were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectra. Results determined that mixing time had a significant impact on the size of Eu-RS NPs, but power output of sonicator and bath temperature had no significant effect. The particle size obtained at the optimum condition (power output of 70 W, bath temperature of 33 °C, and mixing time of 7 min) was less than 200 nm (optimum sizes were 138.9 and 179.5 nm for Eu-RS and PB-loaded Eu-RS NPs, respectively). The optimum PB-loaded Eu-RS NPs at the PB to Eu-RS weight ratio of 1–4 and 20 % of loaded PB released from the nanocarriers within 100 h

  1. Membrane electrodes for the determination of pyridostigmine bromide.

    Science.gov (United States)

    El-Kosasy, Amira M; Salem, Maissa Y; El-Bardicy, Mohamed G; Abd El-Rahman, Mohamed K

    2009-01-01

    Two pyridostigmine bromide (PB) selective electrodes were investigated with 2-nitrophenyl octyl ether as a plasticizer in a polymeric matrix of carboxylated polyvinyl chloride (PVC-COOH), based on the interaction between the drug solution and the dissociated COOH groups in the PVC-COOH. One of the sensors was fabricated by using PVC-COOH only as anionic site without incorporation of an ionophore (sensor 1). The second sensor was constructed by using 2-hydroxy propyl beta-cyclodextrin as an ionophore (sensor 2). Linear responses of PB within a concentration range of 10(-3)-10(-2) and 10(-5)-10(-2) M, with slopes of 51.9 +/- 0.31 and 56.7 +/- 0.40 mV/decade over pH range of 5-10 were obtained using sensors 2 and 1, respectively. The proposed method displayed useful analytical characteristics for determination of PB in tablets with average recoveries of 100.22 +/- 0.62, and 100.15 +/- 0.72, and in plasma with average recoveries of 99.14 +/- 1.19 and 99.79 +/- 0.72, for sensors 2 and 1, respectively. The utility of 2-hydroxy propyl beta-cyclodextrin as an ionophore has a significant influence on increasing both membrane sensitivity and selectivity of sensor 2 in comparison with sensor 1. The methods were also used to determine the intact drug in the presence of its degradate, and thus could be used as stability-indicating methods. The results obtained by the proposed procedures were statistically analyzed and compared with those obtained by the U.S. Pharmacopeia method. No significant difference for either accuracy or precision was observed.

  2. Combined intranasal ipratropium bromide and oxymetazoline in experimental rhinovirus infection.

    Science.gov (United States)

    Pitkäranta, A; Wecker, M T; Korts, D C; Hayden, F G

    1998-01-01

    The topical anticholinergic ipratropium bromide and topical decongestant oxymetazoline were tested to determine whether oxymetazoline alone and the combination were well tolerated and reduced rhinorrhea and middle ear pressure abnormalities during experimental rhinovirus infection. The study was double-bind, placebo-controlled, and double dummy in design. Healthy volunteers (n = 109) with low serum neutralizing antibody titer (oxymetazoline 0.05% two sprays per nostril, oxymetazoline alone, or placebo. Treatments were self administered twice daily for 5 days beginning 1 day after rhinovirus inoculation. The overall infection rate was 83% and of those infected, 88% felt that they had a cold. During the 3-hour period after dosing, the increase in nasal discharge was significantly lower in the combined ipratropium and oxymetazoline (0.13 +/- 0.17 gm/3 hr, mean +/- SE) than after oxymetazoline alone (0.60 +/- 0.18 gm/3 hr) or vehicle (0.73 +/- 0.18 gm/3 hr). Over the 5-day observation period, total daily nasal discharge also tended to be lower in the ipratropium plus oxymetazoline group (3.67 +/- 0.70 gm/24 hr, mean +/- SE) compared to oxymetazoline (5.61 +/- 0.73: 35% reduction) or the vehicle (5.04 +/- 0.73; 27% reduction) recipients, but the differences were not statistically significant. Subjective assessments of rhinorrhea indicated that the severity of rhinorrhea was significantly better among patients receiving oxymetazoline alone or with ipratropium compared to the vehicle. No significant difference in the cumulative frequencies of middle ear pressure abnormalities (27-31%) were found among the treatment groups. Oxymetazoline does not consistently stimulate or decrease nasal mucus production, and ipratropium added to oxymetazoline is well tolerated and reduces rhinorrhea during experimental rhinovirus infection.

  3. Dicationic alkylammonium bromide gemini surfactants. Membrane perturbation and skin irritation.

    Directory of Open Access Journals (Sweden)

    João A S Almeida

    Full Text Available Dicationic alkylammonium bromide gemini surfactants represent a class of amphiphiles potentially effective as skin permeation enhancers. However, only a limited number of studies has been dedicated to the evaluation of the respective cytotoxicity, and none directed to skin irritation endpoints. Supported on a cell viability study, the cytotoxicity of gemini surfactants of variable tail and spacer length was assessed. For this purpose, keratinocyte cells from human skin (NCTC 2544 cell line, frequently used as a model for skin irritation, were employed. The impact of the different gemini surfactants on the permeability and morphology of model vesicles was additionally investigated by measuring the leakage of calcein fluorescent dye and analyzing the NMR spectra of ³¹P, respectively. Detail on the interaction of gemini molecules with model membranes was also provided by a systematic differential scanning calorimetry (DSC and molecular dynamics (MD simulation. An irreversible impact on the viability of the NCTC 2544 cell line was observed for gemini concentrations higher than 25 mM, while no cytotoxicity was found for any of the surfactants in a concentration range up to 10 mM. A higher cytotoxicity was also found for gemini surfactants presenting longer spacer and shorter tails. The same trend was obtained in the calorimetric and permeability studies, with the gemini of longest spacer promoting the highest degree of membrane destabilization. Additional structural and dynamical characterization of the various systems, obtained by ³¹P NMR and MD, provide some insight on the relationship between the architecture of gemini surfactants and the respective perturbation mechanism.

  4. Monitoring of water movement in paddy field's soil using a bromide tracer

    International Nuclear Information System (INIS)

    Asiah Ahmad; Kouichi Yuita

    1994-01-01

    Water movement in soils at the lower course and the middle course of Sakawa River's paddy field was monitored over an 8 week period using a bromide tracer. The water of soil samples taken one day after bromide application contained high concentrations of bromide at 50 to 60 cm soil depth at lower course. The bromide was concentrated promarily within 20 to 80 cm depth. No downward movement below 80 cm depth was detected six weeks afetr the application. This might indicate the high water table of this area. On the other hand, bromide concentrations were high at 50 cm depth in water of the soils sample taken one day after application from the middle course of Sakawa River plot. However, the concentrations were nearly at background level in all samples taken from the middle course of sakawa River 3 weeks after application. The evidence from bromide's movement shows that water readily penetrate the soils at the middle course of Sakawa River. The downward movement was faster compared to that at lower course

  5. Bromine and bromide content in soils: Analytical approach from total reflection X-ray fluorescence spectrometry.

    Science.gov (United States)

    Gallardo, Helena; Queralt, Ignasi; Tapias, Josefina; Candela, Lucila; Margui, Eva

    2016-08-01

    Monitoring total bromine and bromide concentrations in soils is significant in many environmental studies. Thus fast analytical methodologies that entail simple sample preparation and low-cost analyses are desired. In the present work, the possibilities and drawbacks of low-power total reflection X-ray fluorescence spectrometry (TXRF) for the determination of total bromine and bromide contents in soils were evaluated. The direct analysis of a solid suspension using 20 mg of fine ground soil (TXRF analysis can be directly performed by depositing 10 μL of the internal standardized soil extract sample on a quartz glass reflector in a measuring time of 1500 s. The bromide limit of detection by this approach was 10 μg L(-1). Good agreement was obtained between the TXRF results for the total bromine and bromide determinations in soils and those obtained by other popular analytical techniques, e.g. energy dispersive X-ray fluorescence spectrometry (total bromine) and ionic chromatography (bromide). As a study case, the TXRF method was applied to study bromine accumulation in two agricultural soils fumigated with a methyl bromide pesticide and irrigated with regenerated waste water. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Sorption of mercury on chemically synthesized polyaniline

    International Nuclear Information System (INIS)

    Remya Devi, P.S.; Verma, R.; Sudersanan, M.

    2006-01-01

    Sorption of inorganic mercury (Hg 2+ ) and methyl mercury, on chemically synthesized polyaniline, in 0.1-10N HCl solutions has been studied. Hg 2+ is strongly sorbed at low acidities and the extent of sorption decreases with increase in acidity. The sorption of methyl mercury is very low in the HCl concentration range studied. Sorption of Hg 2+ on polyaniline in 0.1-10N LiCl and H 2 SO 4 solutions has also been studied. The analysis of the data indicates that the sorption of Hg 2+ depends on the degree of protonation of polyaniline and the nature of mercury(II) chloride complexes in solution. X-ray photoelectron spectroscopy analysis (XPS) of polyaniline sorbed with mercury show that mercury is bound as Hg 2+ . Sorbed mercury is quantitatively eluted from polyaniline with 0.5N HNO 3 . Polyaniline can be used for separation and pre-concentration of inorganic mercury from aqueous samples. (author)

  7. EPA Leadership in the Global Mercury Partnership

    Science.gov (United States)

    The Global Mercury Partnership is a voluntary multi-stakeholder partnership initiated in 2005 to take immediate actions to protect human health and the environment from the releases of mercury and its compounds to the environment.

  8. Mercury-Containing Devices and Demolition

    Science.gov (United States)

    Some items inside residential buildings contain mercury, which poses a persistent and toxic human health and environmental threat. These materials should be carefully salvaged for proper recycling to prevent mercury contamination prior to demolition.

  9. Health Effects of Exposures to Mercury

    Science.gov (United States)

    ... Mercury in Your Environment Contact Us Share Health Effects of Exposures to Mercury Related Health Information for ... About PDF ; discussion starts on page 20) Methylmercury Effects Effects on People of All Ages Exposure to ...

  10. The effect of longterm exposure to mercury on the bacterial community in marine sediment

    DEFF Research Database (Denmark)

    Rasmussen, Lasse Dam; Sørensen, Søren Johannes

    1998-01-01

    Mercury pollution, bacteria, diversity, mercury resistance, antibiotic resistance, plasmid abundance......Mercury pollution, bacteria, diversity, mercury resistance, antibiotic resistance, plasmid abundance...

  11. Method for the removal and recovery of mercury

    Science.gov (United States)

    Easterly, Clay E.; Vass, Arpad A.; Tyndall, Richard L.

    1997-01-01

    The present invention is an enhanced method for the removal and recovery of mercury from mercury-contaminated matrices. The method involves contacting a mercury-contaminated matrix with an aqueous dispersant solution derived from specific intra-amoebic isolates to release the mercury from the mercury-contaminated matrix and emulsify the mercury; then, contacting the matrix with an amalgamating metal from a metal source to amalgamate the mercury to the amalgamating metal; removing the metallic source from the mercury-contaminated matrix; and heating the metallic source to vaporize the mercury in a closed system to capture the mercury vapors.

  12. Phytoremediation of Ionic and Methyl Mercury Pollution

    Energy Technology Data Exchange (ETDEWEB)

    Meagher, Richard B.

    2004-12-01

    Phytoremediation is defined as the use of plants to extract, resist, detoxify, and/or sequester toxic environmental pollutants. The long-term goal of the proposed research is to develop and test highly productive, field-adapted plant species that have been engineered for the phytoremediation of mercury. A variety of different genes, which should enable plants to clean mercury polluted sites are being tested as tools for mercury phytoremediation, first in model laboratory plants and then in potential field species. Several of these genes have already been shown to enhance mercury phytoremediation. Mercury pollution is a serious, world-wide problem affecting the health of human and wildlife populations. Environmentally, the most serious mercury threat is the production of methylmercury (CH3Hg+) by native bacteria at mercury contaminated wetland sites. Methylmercury is inherently more toxic than metallic (Hg(0)) or ionic (Hg(II)) mercury, and because methylmercury is prolifically biomagnified up the food chain, it poses the most immediate danger to animal populations. We have successfully engineered two model plants, Arabidopsis and tobacco, to use the bacterial merB gene to convert methylmercury to less toxic ionic mercury and to use the bacterial merA gene to further detoxify ionic mercury to the least toxic form of mercury, metallic mercury. Plants expressing both MerA and MerB proteins detoxify methylmercury in two steps to the metallic form. These plants germinate, grow, and set seed at normal growth rates on levels of methylmercury or ionic mercury that are lethal to normal plants. Our newest efforts involve engineering plants with several additional bacterial and plant genes that allow for higher levels of mercury resistance and mercury hyperaccumulation. The potential for these plants to hyperaccumulate mercury was further advanced by developing constitutive, aboveground, and root-specific gene expression systems.

  13. Control of insects with fumigants at low temperatures: toxicity of mixtures of methyl bromide and acrylonitrile to three species of insects

    Energy Technology Data Exchange (ETDEWEB)

    Bond, E.J.; Buckland, C.T.

    1976-12-15

    Acrylonitrile can be mixed with methyl bromide to increase toxicity so that the quantity of methyl bromide required for control of Sitophilus granarius (L.), Tenebrio molitor L., and Tribolium confusum Jacquelin duval is reduced by one half. Mixtures of methyl bromide and acrylonitrile are considerably more effective at low temperatures than methyl bromide alone.

  14. Mercury Continuous Emmission Monitor Calibration

    Energy Technology Data Exchange (ETDEWEB)

    John Schabron; Eric Kalberer; Ryan Boysen; William Schuster; Joseph Rovani

    2009-03-12

    Mercury continuous emissions monitoring systems (CEMs) are being implemented in over 800 coal-fired power plant stacks throughput the U.S. Western Research Institute (WRI) is working closely with the Electric Power Research Institute (EPRI), the National Institute of Standards and Technology (NIST), and the Environmental Protection Agency (EPA) to facilitate the development of the experimental criteria for a NIST traceability protocol for dynamic elemental mercury vapor calibrators/generators. These devices are used to calibrate mercury CEMs at power plant sites. The Clean Air Mercury Rule (CAMR) which was published in the Federal Register on May 18, 2005 and vacated by a Federal appeals court in early 2008 required that calibration be performed with NIST-traceable standards. Despite the vacature, mercury emissions regulations in the future will require NIST traceable calibration standards, and EPA does not want to interrupt the effort towards developing NIST traceability protocols. The traceability procedures will be defined by EPA. An initial draft traceability protocol was issued by EPA in May 2007 for comment. In August 2007, EPA issued a conceptual interim traceability protocol for elemental mercury calibrators. The protocol is based on the actual analysis of the output of each calibration unit at several concentration levels ranging initially from about 2-40 {micro}g/m{sup 3} elemental mercury, and in the future down to 0.2 {micro}g/m{sup 3}, and this analysis will be directly traceable to analyses by NIST. The EPA traceability protocol document is divided into two separate sections. The first deals with the qualification of calibrator models by the vendors for use in mercury CEM calibration. The second describes the procedure that the vendors must use to certify the calibrators that meet the qualification specifications. The NIST traceable certification is performance based, traceable to analysis using isotope dilution inductively coupled plasma

  15. Mechanisms of CPB Modified Zeolite on Mercury Adsorption in Simulated Wastewater.

    Science.gov (United States)

    Liu, Jiang; Huang, Hui; Huang, Rong; Zhang, Jinzhong; Hao, Shuoshuo; Shen, Yuanyuan; Chen, Hong

    2016-06-01

    A systematic study was carried out to analyze the effects of mercury(II) adsorption by surface modified zeolite (SMZ) and adsorption mechanism. Cetylpyridinium bromide (CPB) was used to prepare SMZ. The characterization methods by means of powder X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscope (SEM) showed that both the surface and internal zeolite were covered with CPB molecules, but the main binding sites were surface. Results showed that the organic carbon and cation exchange capacity of the SMZ were 7.76 times and 4.22 times higher than those of natural zeolite (NZ), respectively. Zeta potentials before and after modification were measured at -7.80 mV and -30.27 mV, respectively. Moreover, the saturation adsorptive capacity of SMZ was 16.35 times higher than NZ in mercury-containing wastewater. The possible mechanisms of mercury elimination were surface adsorption, hydrophobic interaction, ion exchange, electricity neutralization. The adsorption process was affected little by competitive ions.

  16. Mercury detection with thermal neutrons

    International Nuclear Information System (INIS)

    Bell, Z.W.

    1994-01-01

    This report describes the work performed to design a gauge to detect mercury concealed within walls, floors, pipes, and equipment inside a building. The project arose out of a desire to decontaminate and decommission (D ampersand D) a building in which mercury had been used as part of a chemical process. The building contains plumbing and equipment, some with residual mercury even after draining, sumps, and hollow walls. So that releases of mercury to the environment might be minimized during D ampersand D activities, it was considered advisable to locate pockets of mercury that may have collected in concealed spaces so that they might be drained in a controlled fashion prior to the application of the wrecking ball or sledge hammer. The detection of such pockets within a building presents some problems not ordinarily encountered in a laboratory environment. Often, only a single side of a wall or pipe is accessible. This condition disqualifies transmission gauges (such as conventional x radiography) in which a probe is sent through the volume under test (VUT) from one side and its passage or attenuation is detected on the opposite side. A robust, one-sided system was needed

  17. Mercury bioaccumulation in the Mediterranean

    Directory of Open Access Journals (Sweden)

    Cinnirella S.

    2013-04-01

    Full Text Available This study details mercury pollution within the food chain of the Mediterranean by analysing the most comprehensive mercury dataset available for biota and water measurements. In this study we computed a bioaccumulation factor (BAF for datasets in the existing mercury-related scientific literature, in on-going programs, and in past measurement campaigns. Preliminary results indicate a major lack of information, making the outcome of any assessment very uncertain. Importantly, not all marine eco-regions are (or have ever been covered by measurement campaigns. Most lacking is information associated with the South-Eastern part of the Mediterranean, and in several eco-regions it is still impossible to reconstruct a trophic net, as the required species were not accounted for when mercury measurements were taken. The datasets also have additional temporal sampling problems, as species were often not sampled systematically (but only sporadically during any given sampling period. Moreover, datasets composed of mercury concentrations in water also suffer from similar geographic limitations, as they are concentrated in the North-Western Mediterranean. Despite these concerns, we found a very clear bioaccumulation trend in 1999, the only year where comprehensive information on both methylmercury concentrations in water and biota was available.

  18. 2,6-Bis(oxazolinyl)phenylnickel(II) Bromide and 2,6-Bis(ketimine)phenylnickel(II) Bromide: Synthesis, Structural Features, and Redox Properties

    NARCIS (Netherlands)

    Stol, M.; Snelders, D.J.M.|info:eu-repo/dai/nl/304836257; Godbole, M.D.; Havenith, R.W.A.|info:eu-repo/dai/nl/205279546; Haddleton, D.M.; Clarkson, G.; Lutz, M.|info:eu-repo/dai/nl/304828971; Spek, A.L.|info:eu-repo/dai/nl/156517566; van Klink, G.P.M.|info:eu-repo/dai/nl/170637964; van Koten, G.|info:eu-repo/dai/nl/073839191

    2007-01-01

    2,6-Bis(oxazolinyl)phenylnickel bromide complexes [NiBr(R,R'-Phebox)] (2) were synthesized via two synthetic routes (A and B). In route A, selective bis-ortho lithiation of [R,R'-PheboxBr], followed by a transmetalation reaction with [NiBr2(PEt3)2], yielded not only complexes 2 with an

  19. Mineral resource of the month: mercury

    Science.gov (United States)

    ,

    2012-01-01

    The article offers information on mercury, a mineral commodity used in industrial and small-scale gold mining applications. Mercury has been reported to be used for amalgamation with gold since the Roman times. Mercury from cinnabar from Almadén, Spain has been used by Romans and has been continued to be used through the Middle Ages and the Colonial era.

  20. 40 CFR 721.10068 - Elemental mercury.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Elemental mercury. 721.10068 Section... Substances § 721.10068 Elemental mercury. (a) Definitions. The definitions in § 721.3 apply to this section... elemental mercury (CAS. No. 7439-97-6) is subject to reporting under this section for the significant new...

  1. How Tiny Collisions Shape Mercury

    Science.gov (United States)

    Kohler, Susanna

    2017-07-01

    If space rocks are unpleasant to encounter, space dust isnt much better. Mercurys cratered surface tells of billions of years of meteoroid impacts but its thin atmosphere is what reveals its collisional history with smaller impactors. Now new research is providing a better understanding of what were seeing.Micrometeoroids Ho!The inner solar system is bombarded by micrometeoroids, tiny particles of dust (on the scale of a tenth of a millimeter) emitted by asteroids and comets as they make their closest approach to the Sun. This dust doesnt penetrateEarths layers of atmosphere, but the innermost planet of our solar system, Mercury, doesnt have this convenient cushioning.Just as Mercury is affected by the impacts of large meteoroids, its also shaped by the many smaller-scale impacts it experiences. These tiny collisions are thought to vaporize atoms and molecules from the planets surface, which quickly dissociate. This process adds metals to Mercurys exosphere, the planets extremely tenuous atmosphere.Modeling PopulationsDistribution of the directions from which meteoroids originate before impacting Mercurys surface, as averaged over its entire orbit. Local time of 12 hr corresponds to the Sun-facing side. A significant asymmetry is seen between the dawn (6 hrs) and dusk (18 hrs) rates. [Pokorn et al. 2017]The metal distribution in the exosphere provides a way for us to measure the effect of micrometeoroid impacts on Mercury but this only works if we have accurate models of the process. A team of scientists led by Petr Pokorn (The Catholic University of America and NASA Goddard SFC) has now worked to improve our picture of micrometeoroid impact vaporization on Mercury.Pokorn and collaborators argue that two meteoroid populations Jupiter-family comets (short-period) and Halley-type comets (long-period) contribute the dust for the majority of micrometeoroid impacts on Mercury. The authors model the dynamics and evolution of these two populations, reproducing the

  2. Separation of mercury(II), methylmercury and phenylmercury by micellar high-performance liquid chromatography on short columns

    International Nuclear Information System (INIS)

    Hutta, M.; Megova, S.; Halko, R.

    1998-01-01

    Three environmentally and agrochemically important mercury species: methylmercury, phenylmercury and mercury(II) are separated within 4 minutes as bromocomplexes by micellar liquid chromatography using very short reversed-phase (RP) C18 columns (up to 30 mm). The micellar mobile phase containing 0.05M cetyltrimethylammonium bromide (CTMA + Br - ), 1% (v/v) 2-propanol, 0.001M cyclohexylenediaminetetraacetic acid (DCTA) and sulfuric acid (pH 2) showed good selectivity in mixed reversed-phase and anion-exchange mode. The above mentioned separation order in which organomercurials are eluted far behind the void volume of the column, but before the mercury(II) peak is advantageous in all instances where mercury(II) is present in real samples in great excess. Environmental and agrochemical samples contain humic material which does not interfere in this particular system. The low cost photometric detection at 500 nm after post-column derivatization by CTMA + Br - micellized dithizone is almost free from interferences and enables detection limits at the 1-3 ng level (e.g., 0.1 ppm Hg) for 20 μl samples. (author)

  3. Control of mercury emissions: policies, technologies, and future trends

    OpenAIRE

    Rhee, Seung-Whee

    2015-01-01

    Seung-Whee Rhee Department of Environmental Engineering, Kyonggi University, Suwon, Republic of Korea Abstract: Owing to the Minamata Convention on Mercury and the Global Mercury Partnership, policies and regulations on mercury management in advanced countries were intensified by a mercury phaseout program in the mercury control strategy. In developing countries, the legislative or regulatory frameworks on mercury emissions are not established specifically, but mercury management is designed...

  4. Canadian mercury inventories: the missing pieces

    Energy Technology Data Exchange (ETDEWEB)

    Hagreen, L.A.; Lourie, B.A. [Summerhill Group, Toronto, ON (Canada)

    2004-07-01

    Research was conducted to determine the significance of the deliberate use of mercury in products in Canada and the associated releases from these sources. Through a combination of literature review and new calculations, the reservoir, flux, and releases of mercury from eight product sources were calculated, and these results compared to historical Canadian inventories. Mercury contributions from the waste sector were also assessed and compared to total Canadian mercury releases and to mercury releases from coal-fired generating stations. Results suggest the use and release of mercury associated with its use in products is 4.5 times what previous inventories indicate. Including dental amalgam and sewage sludge, the total releases of mercury to all environmental compartments in Canada totals 20 tonnes per year. This accounts for less than one-half of the 44 tonnes per year of mercury released from mercury waste disposal each year in Canada. Waste mercury contributions from hazardous waste imports, unknown product sources, and incomplete information on the use of mercury in known products may account for this discrepancy. Waste-related mercury releases and transfers for disposal and recycling are 11 times greater than that of electricity generation in Canada. Results indicate that Canadian inventories have underestimated the significance of mercury use and release associated with products, calling into question the current priorities for mercury management. This paper was developed as part of a panel session at the International Joint Commission 'Mercury in the Ecosystem' workshop, February 26-27, 2003, Windsor, ON, Canada, as a complement to the information on Canadian Inventories presented by Luke Trip (Senes Consulting, Ottawa, ON, Canada).

  5. Gas phase photolysis of ethyl bromide at 253.7 nm

    International Nuclear Information System (INIS)

    Frank, A.J.; Hanrahan, R.J.

    1978-01-01

    The photolysis of ethyl bromide was studied at 100 torr and 23 0 C using 253.7-nm radiation. In the pure system between 60 and 90 s at an absorbed light intensity of 8.3 x 10 13 quanta/cm 3 s the major products and their respective quantum yields are as follows: hydrogen bromide, 0.26; ethane, 0.40; ethylene, 0.028; 1,1-dibromoethane, 0.102; 1,2-dibromoethane, 0.0092; vinyl bromide, 0.009; 1,1,2-tribromoethane, 0.0027; methane, 0.00052; and methyl bromide, 0.00091. When 5 mol % oxygen is added, the quantum yields in this time period become the following: hydrogen bromide, 0.47; ethane, 0.00032; ethylene, 0.0081; 1,1-dibromoethane, 0.0040; 1,2-dibromoethane, 0.022; vinyl bromide, 0; 1,1,2-tribromoethane, 0; methane, 0.0001; and methyl bromide, 0.091. Bromine is also formed with a quantum yield of 0.22. At long photolysis times the HBr and C 2 H 4 go into a stationary state, and the main photolysis products are C 2 H 6 and 1,1-C 2 H 4 Br 2 with quantum yields of 0.24 and 0.17, respectively. The behavior of the system is interpreted based on a model involving C--Br rupture as the main primary process (phi = 0.8) with a substantial contribution of HBr elimination (phi = 0.2). Primary C 2 H 5 . and Br . fragments abstract hydrogen from the substrate to produce mainly the 1-C 2 H 4 Br. radical. Net product formation involves reaction of radical species with Br 2 (present at low, steady-state concentration -5 M), Br. atoms, or HBr. The dynamic behavior of the system was investigated by computer simulation and compared with experimental results. 2 tables, 7 figures

  6. Radiation chemistry and photochemistry of ethyl bromide in the gas phase

    International Nuclear Information System (INIS)

    Frank, A.J.

    1975-01-01

    The primary and secondary decomposition modes of gamma-irradiated ethyl bromide in the gas phase at room temperature have been investigated. Supplementary information on the system has been derived from a parallel study of the 253.7 nm photolysis and the high-pressure mass spectrometry. The G values and quantum yields of the major and minor products both in the absence and in the presence of oxygen are reported. In both the photolysis and radiolysis several products exhibit a well-defined induction period. For the oxygen-free system in the dose range from 1.0 x 10 20 e.v./ gram to 1.5 x 10 20 e.v./gram the major radiolytic products and their respective G values are hydrogen bromide, 3.89; hydrogen, 1.39; ethane, 2.70; ethylene, 2.17; acetylene, 0.31; methane, 0.0831; methyl bromide, 0.080; vinyl bromide, 0.32; 1,1-dibromoethane, 0.88 and 1,2-dibromoethane, 0.12. In the photolysis of the pure system between 60 and 90 seconds at an absorbed light intensity of 7.7 x 10 15 quanta/sec, the major photolytic products and their respective quantum yields are hydrogen bromide, 0.26; ethane, 0.40; ethylene, 0.028; methane, 0.00052; methyl bromide, 0.00091; vinyl bromide, 0.009; 1,1-dibromoethane, 0.102 and 1,2-dibromoethane, 0.0092. Carbon-halogen bond rupture is the major primary event in each system. There is also substantial evidence for HBr elimination. In addition, all secondary processes in the photolysis apparently occur in the radiolysis as well. A numerical integration method capable of handling steady-state assumptions has been used to calculate the product distribution based on the proposed photolysis mechanism. The predicted and experimental product distributions are found to be in reasonable agreement

  7. Sodium Velocity Maps on Mercury

    Science.gov (United States)

    Potter, A. E.; Killen, R. M.

    2011-01-01

    The objective of the current work was to measure two-dimensional maps of sodium velocities on the Mercury surface and examine the maps for evidence of sources or sinks of sodium on the surface. The McMath-Pierce Solar Telescope and the Stellar Spectrograph were used to measure Mercury spectra that were sampled at 7 milliAngstrom intervals. Observations were made each day during the period October 5-9, 2010. The dawn terminator was in view during that time. The velocity shift of the centroid of the Mercury emission line was measured relative to the solar sodium Fraunhofer line corrected for radial velocity of the Earth. The difference between the observed and calculated velocity shift was taken to be the velocity vector of the sodium relative to Earth. For each position of the spectrograph slit, a line of velocities across the planet was measured. Then, the spectrograph slit was stepped over the surface of Mercury at 1 arc second intervals. The position of Mercury was stabilized by an adaptive optics system. The collection of lines were assembled into an images of surface reflection, sodium emission intensities, and Earthward velocities over the surface of Mercury. The velocity map shows patches of higher velocity in the southern hemisphere, suggesting the existence of sodium sources there. The peak earthward velocity occurs in the equatorial region, and extends to the terminator. Since this was a dawn terminator, this might be an indication of dawn evaporation of sodium. Leblanc et al. (2008) have published a velocity map that is similar.

  8. Apparatus for control of mercury

    Science.gov (United States)

    Downs, William; Bailey, Ralph T.

    2001-01-01

    A method and apparatus for reducing mercury in industrial gases such as the flue gas produced by the combustion of fossil fuels such as coal adds hydrogen sulfide to the flue gas in or just before a scrubber of the industrial process which contains the wet scrubber. The method and apparatus of the present invention is applicable to installations employing either wet or dry scrubber flue gas desulfurization systems. The present invention uses kraft green liquor as a source for hydrogen sulfide and/or the injection of mineral acids into the green liquor to release vaporous hydrogen sulfide in order to form mercury sulfide solids.

  9. Coal fired flue gas mercury emission controls

    CERN Document Server

    Wu, Jiang; Pan, Weiguo; Pan, Weiping

    2015-01-01

    Mercury (Hg) is one of the most toxic heavy metals, harmful to both the environment and human health. Hg is released into the atmosphere from natural and anthropogenic sources and its emission control has caused much concern. This book introduces readers to Hg pollution from natural and anthropogenic sources and systematically describes coal-fired flue gas mercury emission control in industry, especially from coal-fired power stations. Mercury emission control theory and experimental research are demonstrated, including how elemental mercury is oxidized into oxidized mercury and the effect of

  10. Marine biogeochemistry of mercury

    International Nuclear Information System (INIS)

    Gill, G.A.

    1986-01-01

    Noncontaminating sample collection and handling procedures and accurate and sensitive analysis methods were developed to measure sub-picomolar Hg concentrations in seawater. Reliable and diagnostic oceanographic Hg distributions were obtained, permitting major processes governing the marine biogeochemistry of Hg to be identified. Mercury concentrations in the northwest Atlantic, central Pacific, southeast Pacific, and Tasman Sea ranged from 0.5 to 12 pM. Vertical Hg distributions often exhibited a maximum within or near the main thermocline. At similar depths, Hg concentrations in the northwest Atlantic Ocean were elevated compared to the N. Pacific Ocean. This pattern appears to result from a combination of enhanced supply of Hg to the northwest Atlantic by rainfall and scavenging removal along deep water circulation pathways. These observations are supported by geochemical steady-state box modelling which predicts a relatively short mean residence time for Hg in the oceans; demonstrating the reactive nature of Hg in seawater and precluding significant involvement in nutrient-type recyclic. Evidence for the rapid removal of Hg from seawater was obtained at two locations. Surface seawater Hg measurements along 160 0 W (20 0 N to 20 0 S) showed a depression in the equatorial upwelling area which correlated well with the transect region exhibiting low 234 Th/ 238 U activity ratios. This relationship implies that Hg will be scavenged and removed from surface seawater in biologically productive oceanic zones. Further, a broad minimum in the vertical distribution of Hg was observed to coincide with the intense oxygen minimum zone in the water column in coastal waters off Peru

  11. In Pseudomonas aeruginosa ethidium bromide does not induce its own degradation or the assembly of pumps involved in its efflux.

    Science.gov (United States)

    Babayan, Anahit; Nikaido, Hiroshi

    2004-11-19

    Xu et al. [Biochem. Biophys. Res. Commun. 305 (2003) 941] reported that, when a mutant strain of Pseudomonas aeruginosa lacking its major multidrug efflux pump complex, MexAB-OprM, was incubated with 100 microM ethidium bromide, the fluorescence, caused by its binding to DNA following its entry into cells, decreased gradually. The authors concluded that the intracellular ethidium bromide "induced" either its degradation or its efflux through the assembly of unknown efflux pumps. We found, through quantitation of ethidium bromide by absorption spectroscopy, that the total amount of ethidium bromide in the system remained constant under these conditions, indicating the absence of its degradation. Furthermore, intracellular ethidium bromide kept increasing during the experiment, showing that the decrease of fluorescence was due to self-quenching, and that ethidium bromide is not pumped out by a newly assembled efflux system.

  12. Environmental contamination and risk assessment of mercury from a historic mercury mine located in southwestern China.

    Science.gov (United States)

    Li, Yonghua

    2013-02-01

    A field survey of mercury pollution in environmental media and human hair samples obtained from residents living in the area surrounding the Chatian mercury mine (CMM) of southwestern China was conducted to evaluate the health risks of mercury to local residents. The results showed that mine waste, and tailings in particular, contained high levels of mercury and that the maximum mercury concentration was 88.50 μg g(-1). Elevated mercury levels were also found in local surface water, paddy soil, and paddy grain, which may cause severe health problems. The mercury concentration of hair samples from the inhabitants of the CMM exceeded 1.0 μg g(-1), which is the limit recommended by the US EPA. Mercury concentrations in paddy soil were positively correlated with mercury concentrations in paddy roots, stalks, and paddy grains, which suggested that paddy soil was the major source of mercury in paddy plant tissue. The average daily dose (ADD) of mercury for local adults and preschool children via oral exposure reached 0.241 and 0.624 μg kg(-1) body weight per day, respectively, which is approaching or exceeds the provisional tolerable daily intake. Among the three oral exposure routes, the greatest contributor to the ADD of mercury was the ingestion of rice grain. Open-stacked mine tailings have resulted in heavy mercury contamination in the surrounding soil, and the depth of appreciable soil mercury concentrations exceeded 100 cm.

  13. Mercury accumulation plant Cyrtomium macrophyllum and its potential for phytoremediation of mercury polluted sites.

    Science.gov (United States)

    Xun, Yu; Feng, Liu; Li, Youdan; Dong, Haochen

    2017-12-01

    Cyrtomium macrophyllum naturally grown in 225.73 mg kg -1 of soil mercury in mining area was found to be a potential mercury accumulator plant with the translocation factor of 2.62 and the high mercury concentration of 36.44 mg kg -1 accumulated in its aerial parts. Pot experiments indicated that Cyrtomium macrophyllum could even grow in 500 mg kg -1 of soil mercury with observed inhibition on growth but no obvious toxic effects, and showed excellent mercury accumulation and translocation abilities with both translocation and bioconcentration factors greater than 1 when exposed to 200 mg kg -1 and lower soil mercury, indicating that it could be considered as a great mercury accumulating species. Furthermore, the leaf tissue of Cyrtomium macrophyllum showed high resistance to mercury stress because of both the increased superoxide dismutase activity and the accumulation of glutathione and proline induced by mercury stress, which favorited mercury translocation from the roots to the aerial parts, revealing the possible reason for Cyrtomium macrophyllum to tolerate high concentration of soil mercury. In sum, due to its excellent mercury accumulation and translocation abilities as well as its high resistance to mercury stress, the use of Cyrtomium macrophyllum should be a promising approach to remediating mercury polluted soils. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Mercury emission monitoring on municipal waste combustion

    International Nuclear Information System (INIS)

    Braun, H.; Gerig, A.

    1991-01-01

    In waste incineration, mercury is the only heavy metal to be released as a gas, mostly as mercury(II) chloride, because of its high volatility. Continuous emission monitoring is possible only when mercury occurs in its elemental form. This paper reports on various possibilities of converting Hg(II) into Hg(0) that has been studied and tested on a laboratory scale and in the TAMARA refuse incineration pilot facility. Continuous mercury emission measurement appears to be possible, provided mercury is converted in the flue gas condensate precipitated. The measuring results obtained on two municipal solid waste and on one sewage treatment sludge incineration plants show that the mercury monitor is a highly sensitive and selective continuously working instrument for mercury emission monitoring

  15. Fate of mercury in the Arctic (FOMA)

    DEFF Research Database (Denmark)

    Skov, H.; Christensen, J.; Asmund, G.

    This report is the final reporting of the project FONA, funded by the Danish Environmental Protection Agency with means from the MIKA/DANCEA funds for Environmental Support to the Arctic Region. The aim of the project is to study the intercompartment mercury transport chain in the arctic area. From...... atmospheric deposition of mercury on sea surfaces to uptake in marine organisms, bio-accumulation, and finally mercury levels in mammals. The studies in the project are focused on the behaviour of mercury during the spring period where special phenomena lead to an enhanced deposition of mercury in the Arctic...... environment, at a time where the marine ecosystem is particularly active. The studies also include a comprehensive time trend study of mercury in top carnivore species. Each of these studies contributes towards establishing the knowledge necessary to develop a general model for transport and uptake of mercury...

  16. Ethidium bromide resistance of L929 cells is accompanied by regular changes in karotype structure

    International Nuclear Information System (INIS)

    Grinchuk, T.M.; Novikova, I.Yu.; Sorokina, E.A.; Sal'nikov, K.V.

    1988-01-01

    Using the method of differential staining of chromosomes for G-bands a comparative karyological analysis of line L 929 mouse cells has been conducted, after the L 929 cells had been sequentially selected for resistance to ethidium bromide at concentrations of 1, 10, 25, and 50 μg/ml and had retained these levels of resistance for a number of cell generations. It was found that the resistant variants exhibited certain karyotypic changes. Only thirteen of the thirty six marker chromosomes typical of the original ethidium bromide-sensitive cells were preserved. Sixteen of the markers were specific for the resistant variants. The changes detected arose at the initial selection stage and were preserved unaltered as the concentration of the toxin was raised. The detection of similar karyotypic changes in cells of clone L 929 of independent origin selected for resistance of 3 μg/ml of ethidium bromide and also in cells of the clone selected for resistance to 25 μg/ml of ethidium bromide and studied previously by the present authors suggests that these changes are universal for L 929 cells resistant to ethidium bromide

  17. Mercury in the environment : a review

    International Nuclear Information System (INIS)

    Goodarzi, F.

    2000-01-01

    Both geogenic and anthropogenic sources are responsible for the input of mercury into the environment. However, mercury comes mostly from geogenic sources and is found naturally in air, water and soil. Crustal degassing results in emission of mercury into the atmosphere. Mercury in water and soil is due mostly to input from sedimentary rocks. Mercury in lake sediments is related mainly to input by country rock and anthropogenic activities such as agriculture. The mercury content of coal is similar to or less than the amount found in the earths crust. Natural charcoal is also able to capture mercury at low temperature combustion. The amount of mercury emitted from the stack of coal-fired power plants is related to the nature of the milled coal and its mineralogical and elemental content. Mercury emissions originating from the combustion of coal from electric utility power plants are considered to be among the greatest contributors to global mercury air emissions. In order to quantify the impact the electric power industry has on the environment, information regarding mercury concentrations in coal and their speciation is needed. For this reason the author examined the behaviour of mercury in three coal samples ashed at increasing temperatures. Mercury removal from coal-fired power plants ranges from 10 to 50 per cent by fabric filters and 20 to 95 per cent by FGD systems. This data will help in regulating emissions of hazardous air pollutants from electric utility steam generating units and will potentially provide insight into the industry's contribution to the global mercury burden. 50 refs

  18. Mercury biogeochemistry: Paradigm shifts, outstanding issues and research needs

    Science.gov (United States)

    Sonke, Jeroen E.; Heimbürger, Lars-Eric; Dommergue, Aurélien

    2013-05-01

    Half a century of mercury research has provided scientists and policy makers with a detailed understanding of mercury toxicology, biogeochemical cycling and past and future impacts on human exposure. The complexity of the global biogeochemical mercury cycle has led to repeated and ongoing paradigm shifts in numerous mercury-related disciplines and outstanding questions remain. In this review, we highlight some of the paradigm shifts and questions on mercury toxicity, the risks and benefits of seafood consumption, the source of mercury in seafood, and the Arctic mercury cycle. We see a continued need for research on mercury toxicology and epidemiology, for marine mercury dynamics and ecology, and for a closer collaboration between observational mercury science and mercury modeling in general. As anthropogenic mercury emissions are closely tied to the energy cycle (in particular coal combustion), mercury exposure to humans and wildlife are likely to persist unless drastic emission reductions are put in place.

  19. Mercury erosion experiments for spallation target system

    International Nuclear Information System (INIS)

    Kinoshita, Hidetaka; Kaminaga, Masanori; Haga, Katsuhiro; Hino, Ryutaro

    2003-01-01

    The Japan Atomic Energy Research Institute (JAERI) and the High Energy Accelerator Research Organization (KEK) are promoting a plan to construct the spallation neutron source at the Tokai Research Establishment, JAERI, under the High-Intensity Proton Accelerator Project (J-PARC). A mercury circulation system has been designed so as to supply mercury to the target stably under the rated flow rate of 41 m 3 /hr. Then, it was necessary to confirm a mercury pump performance from the viewpoint of making the mercury circulation system feasible, and more, to investigate erosion rate under the mercury flow as well as an amount of mercury remained on the surface after drain from the viewpoints of mechanical strength relating to the lifetime and remote handling of mercury components. The mercury pump performance was tested under the mercury flow conditions by using an experimental gear pump, which had almost the same structure as a practical mercury pump to be expected in the mercury circulation system, and the erosion rates in a mercury pipeline as well as the amount of mercury remained on the surface were also investigated. The discharged flow rates of the experimental gear pump increased linearly with the rotation speed, so that the gear pump would work as the flow meter. Erosion rates obtained under the mercury velocity less than 1.6 m/s was found to be so small that decrease of pipeline wall thickness would be 390 μm after 30-year operation under the rated mercury velocity of 0.7 m/s. For the amount of remaining mercury on the pipeline, remaining rates of weight and volume were estimated at 50.7 g/m 2 and 3.74 Hg-cm 3 /m 2 , respectively. Applying these remaining rates of weight and volume to the mercury target, the remaining mercury was estimated at about 106.5 g and 7.9 cm 3 . Radioactivity of this remaining mercury volume was found to be three-order lower than that of the target casing. (author)

  20. Methyl bromide: ocean sources, ocean sinks, and climate sensitivity.

    Science.gov (United States)

    Anbar, A D; Yung, Y L; Chavez, F P

    1996-03-01

    The oceans play an important role in the geochemical cycle of methyl bromide (CH3Br), the major carrier of O3-destroying bromine to the stratosphere. The quantity of CH3Br produced annually in seawater is comparable to the amount entering the atmosphere each year from natural and anthropogenic sources. The production mechanism is unknown but may be biological. Most of this CH3Br is consumed in situ by hydrolysis or reaction with chloride. The size of the fraction which escapes to the atmosphere is poorly constrained; measurements in seawater and the atmosphere have been used to justify both a large oceanic CH3Br flux to the atmosphere and a small net ocean sink. Since the consumption reactions are extremely temperature-sensitive, small temperature variations have large effects on the CH3Br concentration in seawater, and therefore on the exchange between the atmosphere and the ocean. The net CH3Br flux is also sensitive to variations in the rate of CH3Br production. We have quantified these effects using a simple steady state mass balance model. When CH3Br production rates are linearly scaled with seawater chlorophyll content, this model reproduces the latitudinal variations in marine CH3Br concentrations observed in the east Pacific Ocean by Singh et al. [1983] and by Lobert et al. [1995]. The apparent correlation of CH3Br production with primary production explains the discrepancies between the two observational studies, strengthening recent suggestions that the open ocean is a small net sink for atmospheric CH3Br, rather than a large net source. The Southern Ocean is implicated as a possible large net source of CH3Br to the atmosphere. Since our model indicates that both the direction and magnitude of CH3Br exchange between the atmosphere and ocean are extremely sensitive to temperature and marine productivity, and since the rate of CH3Br production in the oceans is comparable to the rate at which this compound is introduced to the atmosphere, even small

  1. Touchstones and mercury at Hedeby

    Czech Academy of Sciences Publication Activity Database

    Ježek, Martin; Holub, M.

    2014-01-01

    Roč. 89, č. 1 (2014), s. 193-204 ISSN 0079-4848 Institutional support: RVO:67985912 Keywords : Hedeby * Viking Age * grave goods * touchstone * precious metal * mercury * chemical microanalysis * archaeometallurgy Subject RIV: AC - Archeology, Anthropology, Ethnology Impact factor: 0.278, year: 2014

  2. PERCEPTION OF MERCURY RISK INFORMATION

    Science.gov (United States)

    Approximately 8% of American women have blood Mercury levels exceeding the EPA reference dose (a dose below which symptoms would be unlikely). The children of these women are at risk of neurological deficits (lower IQ scores) primarily because of the mother's consumption of conta...

  3. A downstream voyage with mercury

    Science.gov (United States)

    Heinz, Gary

    2016-01-01

    Retrospective essay for the Bulletin of Environmental Contamination and Toxicology.As I look back on my paper, “Effects of Low Dietary Levels of Methyl Mercury on Mallard Reproduction,” published in 1974 in the Bulletin of Environmental Contamination and Toxicology, a thought sticks in my mind. I realize just how much my mercury research was not unlike a leaf in a stream, carried this way and that, sometimes stalled in an eddy, restarted, and carried downstream at a pace and path that was not completely under my control. I was hired in 1969 by the Patuxent Wildlife Research Center to study the effects of environmental pollutants on the behavior of wildlife. A colleague was conducting a study on the reproductive effects of methylmercury on mallards (Anas platyrhynchos), and he offered to give me some of the ducklings. I conducted a pilot study, testing how readily ducklings approached a tape-recorded maternal call. Sample sizes were small, but the results suggested that ducklings from mercury-treated parents behaved differently than controls. That’s how I got into mercury research—pretty much by chance.

  4. Venus and Mercury as Planets

    Science.gov (United States)

    1974-01-01

    A general evolutionary history of the solar planetary system is given. The previously observed characteristics of Venus and Mercury (i.e. length of day, solar orbit, temperature) are discussed. The role of the Mariner 10 space probe in gathering scientific information on the two planets is briefly described.

  5. Venus and Mercury as planets

    International Nuclear Information System (INIS)

    1974-01-01

    A general evolutionary history of the solar planetary system is given. The previously observed characteristics of Venus and Mercury (i.e. length of day, solar orbit, temperature) are discussed. The role of the Mariner 10 space probe in gathering scientific information on the two planets is briefly described

  6. 76 FR 75446 - Amendment of Class E Airspace; Mercury, NV

    Science.gov (United States)

    2011-12-02

    ...-0894; Airspace Docket No. 11-AWP-14] Amendment of Class E Airspace; Mercury, NV AGENCY: Federal... Mercury, Desert Rock Airport, Mercury, NV. Decommissioning of the Mercury Non-Directional Beacon (NDB) at Mercury, Desert Rock Airport has made this action necessary for the safety and management of Instrument...

  7. Chloride/bromide ratios in leachate derived from farm-animal waste.

    Science.gov (United States)

    Hudak, Paul F

    2003-01-01

    Ratios of conservative chemicals have been used to identify sources of groundwater contamination. While chloride/bromide ratios have been reported for several common sources of groundwater contamination, little work has been done on leachate derived from farm-animal waste. In this study, chloride/bromide ratios were measured in leachate derived from longhorn-cattle, quarterhorse, and pygme-goat waste at a farm in Abilene, Texas, USA. (Minimum, median, and maximum) chloride/bromide ratios of (66.5, 85.6, and 167), (119, 146, and 156), and (35.4, 57.8, and 165) were observed for cattle, horses, and goats, respectively. These ratios are below typical values for domestic wastewater and within the range commonly observed for oilfield brine. Results of this study have important implications for identifying sources of contaminated groundwater in settings with significant livestock and/or oil production.

  8. Effects of caffeine on cleavage delay of sea urchin eggs induced by ethidium bromide or puromycin

    International Nuclear Information System (INIS)

    Kimura, Hiroshi

    1975-01-01

    The mitotic delay was induced when sea urchin eggs were treated with either ethidium bromide or puromycin, as observed with eggs fertilized with x- or UV-irradiated sperm. Treatment of these eggs with caffeine during the period of early prophase block resulted in the reduction of the mitotic delay. Protein synthesis of these eggs was not affected by x-irradiation but inhibited by ethidium bromide or puromycin. Caffeine was almost ineffective in changing the protein synthesis of eggs inseminated with x-irradiated sperm or treated with ethidium bromide. These facts mean that additive synthesis of protein is not required for the reduction by caffeine of the mitotic delay. Some role of protein synthesis in the reduction by caffeine of the cleavage delay is not excluded for puromycin treated eggs, since caffeine counteracted the inhibitory effect of puromycin on protein synthesis. (author)

  9. Corrosion Behavior of Austenitic and Duplex Stainless Steels in Lithium Bromide

    Directory of Open Access Journals (Sweden)

    Ayo Samuel AFOLABI

    2009-07-01

    Full Text Available The corrosion behavior of austenitic and duplex stainless steels in various concentrations of lithium, bromide solution was investigated by using the conventional weight loss measurement method. The results obtained show that corrosion of these steels occurred due to the aggressive bromide ion in the medium. Duplex stainless steel shows a greater resistance to corrosion than austenitic stainless steel in the medium. This was attributed to equal volume proportion of ferrite and austenite in the structure of duplex stainless steel coupled with higher content of chromium in its composition. Both steels produced electrochemical noise at increased concentrations of lithium bromide due to continuous film breakdown and repair caused by reduction in medium concentration by the alkaline corrosion product while surface passivity observed in duplex stainless steel is attributed to film stability on this steel.

  10. The structure of adsorbed bromide concurrent with the underpotential deposition (UPD) of Cu on Pt(111)

    Science.gov (United States)

    Marković, Nenad M.; Lucas, Chris A.; Gasteiger, Hubert A.; Ross, Philip N.

    1997-02-01

    The adsorption of bromide anions concurrent with the underpotential deposition (UPD) of Cu on Pt(111) was examined utilizing ex-situ LEED and in-situ surface X-ray scattering for structure determination, in combination with coverage determination by rotating ring disk flux measurements with the Pt(111) single crystal as the disk electrode. The results show definitively that Cu UPD on Pt(111) in the presence of bromide is a two-step process, with the total amount of Cu deposited at underpotentials ˜0.95 ± 5% ML (1 ML = 1 adatom per Pt atom). The results also indicate that the surface coverage by adsorbed bromide undergoes only a small (UPD on Pt(111) in solutions containing chloride anions.

  11. The Plasma Environment at Mercury

    Science.gov (United States)

    Raines, James M.; Gershman, Daniel J.; Zurbuchen, Thomas H.; Gloeckler, George; Slavin, James A.; Anderson, Brian J.; Korth, Haje; Krimigis, Stamatios M.; Killen, Rosemary M.; Sarantos, Menalos; hide

    2011-01-01

    Mercury is the least explored terrestrial planet, and the one subjected to the highest flux of solar radiation in the heliosphere. Its highly dynamic, miniature magnetosphere contains ions from the exosphere and solar wind, and at times may allow solar wind ions to directly impact the planet's surface. Together these features create a plasma environment that shares many features with, but is nonetheless very different from, that of Earth. The first in situ measurements of plasma ions in the Mercury space environment were made only recently, by the Fast Imaging Plasma Spectrometer (FIPS) during the MESSENGER spacecraft's three flybys of the planet in 2008-2009 as the probe was en route to insertion into orbit about Mercury earlier this year. Here. we present analysis of flyby and early orbital mission data with novel techniques that address the particular challenges inherent in these measurements. First. spacecraft structures and sensor orientation limit the FIPS field of view and allow only partial sampling of velocity distribution functions. We use a software model of FIPS sampling in velocity space to explore these effects and recover bulk parameters under certain assumptions. Second, the low densities found in the Mercury magnetosphere result in a relatively low signal-to-noise ratio for many ions. To address this issue, we apply a kernel density spread function to guide removal of background counts according to a background-signature probability map. We then assign individual counts to particular ion species with a time-of-flight forward model, taking into account energy losses in the carbon foil and other physical behavior of ions within the instrument. Using these methods, we have derived bulk plasma properties and heavy ion composition and evaluated them in the context of the Mercury magnetosphere.

  12. Chemical form matters: differential accumulation of mercury following inorganic and organic mercury exposures in zebrafish larvae.

    Science.gov (United States)

    Korbas, Malgorzata; Macdonald, Tracy C; Pickering, Ingrid J; George, Graham N; Krone, Patrick H

    2012-02-17

    Mercury, one of the most toxic elements, exists in various chemical forms each with different toxicities and health implications. Some methylated mercury forms, one of which exists in fish and other seafood products, pose a potential threat, especially during embryonic and early postnatal development. Despite global concerns, little is known about the mechanisms underlying transport and toxicity of different mercury species. To investigate the impact of different mercury chemical forms on vertebrate development, we have successfully combined the zebrafish, a well-established developmental biology model system, with synchrotron-based X-ray fluorescence imaging. Our work revealed substantial differences in tissue-specific accumulation patterns of mercury in zebrafish larvae exposed to four different mercury formulations in water. Methylmercury species not only resulted in overall higher mercury burdens but also targeted different cells and tissues than their inorganic counterparts, thus revealing a significant role of speciation in cellular and molecular targeting and mercury sequestration. For methylmercury species, the highest mercury concentrations were in the eye lens epithelial cells, independent of the formulation ligand (chloride versusl-cysteine). For inorganic mercury species, in absence of l-cysteine, the olfactory epithelium and kidney accumulated the greatest amounts of mercury. However, with l-cysteine present in the treatment solution, mercuric bis-l-cysteineate species dominated the treatment, significantly decreasing uptake. Our results clearly demonstrate that the common differentiation between organic and inorganic mercury is not sufficient to determine the toxicity of various mercury species.

  13. Chemical Form Matters: Differential Accumulation of Mercury Following Inorganic and Organic Mercury Exposures in Zebrafish Larvae

    Energy Technology Data Exchange (ETDEWEB)

    Korbas, Malgorzata; MacDonald, Tracy C.; Pickering, Ingrid J.; George, Graham N.; Krone, Patrick H. (Saskatchewan)

    2013-04-08

    Mercury, one of the most toxic elements, exists in various chemical forms each with different toxicities and health implications. Some methylated mercury forms, one of which exists in fish and other seafood products, pose a potential threat, especially during embryonic and early postnatal development. Despite global concerns, little is known about the mechanisms underlying transport and toxicity of different mercury species. To investigate the impact of different mercury chemical forms on vertebrate development, we have successfully combined the zebrafish, a well-established developmental biology model system, with synchrotron-based X-ray fluorescence imaging. Our work revealed substantial differences in tissue-specific accumulation patterns of mercury in zebrafish larvae exposed to four different mercury formulations in water. Methylmercury species not only resulted in overall higher mercury burdens but also targeted different cells and tissues than their inorganic counterparts, thus revealing a significant role of speciation in cellular and molecular targeting and mercury sequestration. For methylmercury species, the highest mercury concentrations were in the eye lens epithelial cells, independent of the formulation ligand (chloride versus L-cysteine). For inorganic mercury species, in absence of L-cysteine, the olfactory epithelium and kidney accumulated the greatest amounts of mercury. However, with L-cysteine present in the treatment solution, mercuric bis-L-cysteineate species dominated the treatment, significantly decreasing uptake. Our results clearly demonstrate that the common differentiation between organic and inorganic mercury is not sufficient to determine the toxicity of various mercury species.

  14. Iodate and iodo-trihalomethane formation during chlorination of iodide-containing waters: role of bromide.

    Science.gov (United States)

    Criquet, Justine; Allard, Sebastien; Salhi, Elisabeth; Joll, Cynthia A; Heitz, Anna; von Gunten, Urs

    2012-07-03

    The kinetics of iodate formation is a critical factor in mitigation of the formation of potentially toxic and off flavor causing iodoorganic compounds during chlorination. This study demonstrates that the formation of bromine through the oxidation of bromide by chlorine significantly enhances the oxidation of iodide to iodate in a bromide-catalyzed process. The pH-dependent kinetics revealed species specific rate constants of k(HOBr + IO(-)) = 1.9 × 10(6) M(-1) s(-1), k(BrO(-) + IO(-)) = 1.8 × 10(3) M(-1) s(-1), and k(HOBr + HOI) < 1 M(-1) s(-1). The kinetics and the yield of iodate formation in natural waters depend mainly on the naturally occurring bromide and the type and concentration of dissolved organic matter (DOM). The process of free chlorine exposure followed by ammonia addition revealed that the formation of iodo-trihalomethanes (I-THMs), especially iodoform, was greatly reduced by an increase of free chlorine exposure and an increase of the Br(-)/I(-) ratio. In water from the Great Southern River (with a bromide concentration of 200 μg/L), the relative I-incorporation in I-THMs decreased from 18 to 2% when the free chlorine contact time was increased from 2 to 20 min (chlorine dose of 1 mg Cl(2)/L). This observation is inversely correlated with the conversion of iodide to iodate, which increased from 10 to nearly 90%. Increasing bromide concentration also increased the conversion of iodide to iodate: from 45 to nearly 90% with a bromide concentration of 40 and 200 μg/L, respectively, and a prechlorination time of 20 min, while the I-incorporation in I-THMs decreased from 10 to 2%.

  15. Irradiation as a disinfestation method - update on methyl bromide phase out, regulatory action and emerging opportunities

    International Nuclear Information System (INIS)

    Marcotte, Michelle

    1998-01-01

    Methyl bromide (MeBr), is the most widely used agricultural fumigant in the world for the control of pests and plant diseases. It is used to control pests and diseases in food, agricultural and forestry commodities after harvest, before or during storage or transportation and/or at time of import to control quarantine or storage pests. Knowing MeBr will be phased out has spurred a search for alternative treatments and products, and has placed pressure on regulatory authorities to approve alternatives. Some of methyl bromide use could be replaced with irradiation. Methyl bromide is also used for soil and structural fumigation, and although there is some use of irradiation for packaged soil or greenhouse products, in general, these uses can not be replaced by irradiation. Some radiation processing facilities have either seen increased business to disinfest commodities, or have experienced more inquiries for service. There are many other processes and products competing for this market and irradiation will not win its share of the business without an improved regulatory picture, improved marketing to methyl bromide users and improved information to answer questions from commodity sectors. The United Nations Environment Program - Methyl Bromide Technical Options Committee (MBTOC) provides a venue for the publication or information about the use and availability of irradiation as an alternative to methyl bromide. It provides the technical base to the Montreal Protocol contributing to the setting of phase out dates; this committee is actively researching and assessing all alternatives and needs information about irradiation. The author is a member of the MBTOC committee

  16. Mercury emission from crematories in Japan

    Directory of Open Access Journals (Sweden)

    M. Takaoka

    2010-04-01

    Full Text Available Anthropogenic sources of mercury emissions have a significant impact on global pollution. Therefore, finding uncharacterised sources and assessing the emissions from these sources are important. However, limited data are available worldwide on mercury emissions from crematories. In Japan, 99.9% of dead bodies are cremated, which is the highest percentage in the world, and more than 1600 crematories are in operation. We thus focused on emissions from crematories in Japan. The number of targeted facilities was seven, and we used continuous emission monitoring to measure the mercury concentrations and investigate mercury behaviour. The total mercury concentrations in stack gases were a few μg/Nm3 (normal cubic meters. Considering the time profile of mercury and its species in cremations, the findings confirmed that the mercury in stack gas originated from dental amalgam. The amount of mercury emissions was calculated using the total concentration and gas flow rate. Furthermore, the annual amount of mercury emission from crematories in Japan was estimated by using the total number of corpses. The emission amount was considerably lower than that estimated in the United Kingdom. From statistical analyses on population demographics and measurements, future total emissions from crematories were also predicted. As a result, the amount of mercury emitted by crematories will likely increase by 2.6-fold from 2007 to 2037.

  17. Environmental Mercury and Its Toxic Effects

    Directory of Open Access Journals (Sweden)

    Kevin M. Rice

    2014-03-01

    Full Text Available Mercury exists naturally and as a man-made contaminant. The release of processed mercury can lead to a progressive increase in the amount of atmospheric mercury, which enters the atmospheric-soil-water distribution cycles where it can remain in circulation for years. Mercury poisoning is the result of exposure to mercury or mercury compounds resulting in various toxic effects depend on its chemical form and route of exposure. The major route of human exposure to methylmercury (MeHg is largely through eating contaminated fish, seafood, and wildlife which have been exposed to mercury through ingestion of contaminated lower organisms. MeHg toxicity is associated with nervous system damage in adults and impaired neurological development in infants and children. Ingested mercury may undergo bioaccumulation leading to progressive increases in body burdens. This review addresses the systemic pathophysiology of individual organ systems associated with mercury poisoning. Mercury has profound cellular, cardiovascular, hematological, pulmonary, renal, immunological, neurological, endocrine, reproductive, and embryonic toxicological effects.

  18. Mercury emissions from municipal solid waste combustors

    Energy Technology Data Exchange (ETDEWEB)

    1993-05-01

    This report examines emissions of mercury (Hg) from municipal solid waste (MSW) combustion in the United States (US). It is projected that total annual nationwide MSW combustor emissions of mercury could decrease from about 97 tonnes (1989 baseline uncontrolled emissions) to less than about 4 tonnes in the year 2000. This represents approximately a 95 percent reduction in the amount of mercury emitted from combusted MSW compared to the 1989 mercury emissions baseline. The likelihood that routinely achievable mercury emissions removal efficiencies of about 80 percent or more can be assured; it is estimated that MSW combustors in the US could prove to be a comparatively minor source of mercury emissions after about 1995. This forecast assumes that diligent measures to control mercury emissions, such as via use of supplemental control technologies (e.g., carbon adsorption), are generally employed at that time. However, no present consensus was found that such emissions control measures can be implemented industry-wide in the US within this time frame. Although the availability of technology is apparently not a limiting factor, practical implementation of necessary control technology may be limited by administrative constraints and other considerations (e.g., planning, budgeting, regulatory compliance requirements, etc.). These projections assume that: (a) about 80 percent mercury emissions reduction control efficiency is achieved with air pollution control equipment likely to be employed by that time; (b) most cylinder-shaped mercury-zinc (CSMZ) batteries used in hospital applications can be prevented from being disposed into the MSW stream or are replaced with alternative batteries that do not contain mercury; and (c) either the amount of mercury used in fluorescent lamps is decreased to an industry-wide average of about 27 milligrams of mercury per lamp or extensive diversion from the MSW stream of fluorescent lamps that contain mercury is accomplished.

  19. Mercury exposure from interior latex paint.

    Science.gov (United States)

    Agocs, M M; Etzel, R A; Parrish, R G; Paschal, D C; Campagna, P R; Cohen, D S; Kilbourne, E M; Hesse, J L

    1990-10-18

    Many paint companies have used phenylmercuric acetate as a preservative to prolong the shelf life of interior latex paint. In August 1989, acrodynia, a form of mercury poisoning, occurred in a child exposed to paint fumes in a home recently painted with a brand containing 4.7 mmol of mercury per liter (at that time the Environmental Protection Agency's recommended limit was 1.5 mmol or less per liter). To determine whether the recent use of that brand of paint containing phenylmercuric acetate was associated with elevated indoor-air and urinary mercury concentrations, we studied 74 "exposed" persons living in 19 homes recently painted with the brand and 28 "unexposed" persons living in 10 homes not recently painted with paint containing mercury. The paint samples from the homes of exposed persons contained a median of 3.8 mmol of mercury per liter, and air samples from the homes had a median mercury content of 10.0 nmol per cubic meter (range, less than 0.5 to 49.9). No mercury was detected in paint or air samples from the homes of unexposed persons. The median urinary mercury concentration was higher in the exposed persons (4.7 nmol of mercury per millimole of creatinine; range, 1.4 to 66.5) than in the unexposed persons (1.1 nmol per millimole; range, 0.02 to 3.9; P less than 0.001). Urinary mercury concentrations within the range that we found in exposed persons have been associated with symptomatic mercury poisoning. We found that potentially hazardous exposure to mercury had occurred among persons whose homes were painted with a brand of paint containing mercury at concentrations approximately 2 1/2 times the Environmental Protection Agency's recommended limit.

  20. Well-Defined Copper(I) Fluoroalkoxide Complexes for Trifluoroethoxylation of Aryl and Heteroaryl Bromides

    KAUST Repository

    Huang, Ronglu

    2015-03-17

    © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. Copper(I) fluoroalkoxide complexes bearing dinitrogen ligands were synthesized and the structure and reactivity of the complexes toward trifluoroethoxylation, pentafluoropropoxylation, and tetrafluoropropoxylation of aryl and heteroaryl bromides were investigated. Efficiency drive: A series of copper(I) fluoroalkoxide complexes bearing N,N ligands have been prepared and structurally characterized. These well-defined complexes serve as efficient reagents for the fluoroalkoxylation of aryl and heteroaryl bromides to produce a wide range of trifluoroethyl, pentafluoropropyl, and tetrafluoropropyl (hetero)aryl ethers in good to excellent yields.

  1. Thermodynamic evaluation of new absorbent mixtures of lithium bromide and organic salts for absorption refrigeration machines

    Energy Technology Data Exchange (ETDEWEB)

    Donate, Marina; Rodriguez, Luis; Lucas, Antonio De; Rodriguez, Juan F. [Department of Chemical Engineering, University of Castilla-La Mancha, Avda. de Camilo Jose Cela s/n, 13004 Ciudad Real (Spain)

    2006-01-01

    Mixtures of lithium bromide and organic salts of sodium and potassium (formate, acetate and lactate) have been evaluated as alternative absorbents for absorption refrigeration machines. The main objective is to overpass the limitations of lithium bromide and improve the characteristics and the efficiency of the refrigeration cycle. In order to select the mixture that presents better properties for its employment in absorption refrigeration cycles, a thermodynamic analysis have been done. Density, viscosity, enthalpies of dilution, solubility and vapour pressure data of the proposed mixtures have been measured. A simulation program has been developed to evaluate temperatures, heats exchanged in the different sections and the efficiency of the cycle. (author)

  2. Temperature Dependence of Mineral Solubility in Water. Part 2. Alkaline and Alkaline Earth Bromides

    Science.gov (United States)

    Krumgalz, B. S.

    2018-03-01

    Databases of alkaline and alkaline earth bromide solubilities in water at various temperatures were created using experimental data from publications over about the last two centuries. Statistical critical evaluation of the created databases was produced since there were enough independent data sources to justify such evaluation. The reliable experimental data were adequately described by polynomial expressions over various temperature ranges. Using the Pitzer approach for ionic activity and osmotic coefficients, the thermodynamic solubility products for the discussed bromide minerals have been calculated at various temperature intervals and also represented by polynomial expressions.

  3. Barbier-Negishi Coupling of Secondary Alkyl Bromides with Aryl and Alkenyl Triflates and Nonaflates.

    Science.gov (United States)

    Zhang, Ke-Feng; Christoffel, Fadri; Baudoin, Olivier

    2018-02-12

    A mild and practical Barbier-Negishi coupling of secondary alkyl bromides with aryl and alkenyl triflates and nonaflates has been developed. This challenging reaction was enabled by the use of a very bulky imidazole-based phosphine ligand, which resulted in good yields as well as good chemo- and site selectivities for a broad range of substrates at room temperature and under non-aqueous conditions. This reaction was extended to primary alkyl bromides by using an analogous pyrazole-based ligand. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Halide-mediated regioselective 6-O-glycosylation of unprotected hexopyranosides with perbenzylated glycosyl bromide donors

    DEFF Research Database (Denmark)

    Niedbal, Dominika Alina; Madsen, Robert

    2016-01-01

    The regio- and stereoselective glycosylation at the 6-position in 2,3,4,6-unprotected hexopyranosides has been investigated with dibutyltin oxide as the directing agent. Perbenzylated hexopyranosyl bromides were employed as the donors and the glycosylations were promoted by tetrabutylammonium...... bromide. The couplings were completely selective for both glucose and galactose donors and acceptors as long as the stannylene acetal of the acceptor was soluble in dichloromethane. This gave rise to a number of 1,2-cis-linked disaccharides in reasonable yields. Mannose donors and acceptors, on the other...

  5. Determination by neutron activation analysis of loss of arsenic, antimony, bromine and mercury during lyophilization

    International Nuclear Information System (INIS)

    Carlson, M.; Litman, R.

    1978-01-01

    Neutron activation analysis has been used to monitor the loss of arsenic, as dimethylarsinic acid, (CH 3 ) 2 AsOOH, or as sodium arsenate (Na 2 HAsO 4 .7H 2 O), antimony (as potassium antimony, tartrate, KSbC 4 O 7 .1/2H 2 O) and bromine (as bromide ion) during lyophilization of acidified and neutral aqueous synthetic and environmental samples. Losses of Sb and As ranged from zero to 60%, while losses of bromine were constant (at 91%) in acidic solutions. The variable losses of As and Sb were due solely to the presence of and partial decomposition of the (CH 3 ) 2 AsOOH. Electrochemical oxidation of Br - to Br 2 is responsible for the high losses of bromine. In addition losses of mercury (as methylmercuric chloride) were 1O0% in both acidic and neutral aqueous synthetic samples during lyophilization. (author)

  6. RECOVERY OF MERCURY FROM CONTAMINATED LIQUID WASTES

    Energy Technology Data Exchange (ETDEWEB)

    Robin M. Stewart

    1999-09-29

    Mercury was widely used in U.S. Department of Energy (DOE) weapons facilities, resulting in a broad range of mercury-contaminated wastes and wastewaters. Some of the mercury contamination has escaped to the local environment, particularly at the Y-12 Plant in Oak Ridge, Tennessee, where approximately 330 metric tons of mercury were discharged to the environment between 1953 and 1963 (TN & Associates, 1998). Effective removal of mercury contamination from water is a complex and difficult problem. In particular, mercury treatment of natural waters is difficult because of the low regulatory standards. For example, the Environmental Protection Agency has established a national ambient water quality standard of 12 parts-per-trillion (ppt), whereas the standard is 1.8 ppt in the Great Lakes Region. In addition, mercury in the environment is typically present in several different forms, but sorption processes are rarely effective with more than one or two of these forms. To meet the low regulatory discharge limits, an effective sorption process must be able to address all forms of mercury present in the water. One approach is to apply different sorbents in series depending on the mercury speciation and the regulatory discharge limits. ADA Technologies, Inc. has developed four new sorbents to address the variety of mercury species present in industrial discharges and natural waters. Three of these sorbents have been field tested on contaminated creek water at the Y-12 Plant. Two of these sorbents have been successfully demonstrated very high removal efficiencies for soluble mercury species, reducing mercury concentrations at the outlet of a pilot-scale system to less than 12 ppt for as long as six months. The other sorbent tested at the Y-12 Plant targeted colloidal mercury not removed by standard sorption or filtration processes. At the Y-12 Plant, colloidal mercury appears to be associated with iron, so a sorbent that removes mercury-iron complexes in the presence of a

  7. Organic, inorganic and total mercury determination in fish by chemical vapor generation with collection on a gold gauze and electrothermal atomic absorption spectrometry

    International Nuclear Information System (INIS)

    Duarte, Fabio Andrei; Bizzi, Cezar Augusto; Goldschmidt Antes, Fabiane; Dressler, Valderi Luiz; Flores, Erico Marlon de Moraes

    2009-01-01

    A method for organic, inorganic and total mercury determination in fish tissue has been developed using chemical vapor generation and collection of mercury vapor on a gold gauze inside a graphite tube and further atomization by electrothermal atomic absorption spectrometry. After drying and cryogenic grinding, potassium bromide and hydrochloric acid solution (1 mol L - 1 KBr in 6 mol L - 1 HCl) was added to the samples. After centrifugation, total mercury was determined in the supernatant. Organomercury compounds were selectively extracted from KBr solution using chloroform and the resultant solution was back extracted with 1% m/v L-cysteine. This solution was used for organic Hg determination. Inorganic Hg remaining in KBr solution was directly determined by chemical vapor generation electrothermal atomic absorption spectrometry. Mercury vapor generation from extracts was performed using 1 mol L - 1 HCl and 2.5% m/v NaBH 4 solutions and a batch chemical vapor generation system. Mercury vapor was collected on the gold gauze heated resistively at 80 deg. C and the atomization temperature was set at 650 deg. C. The selectivity of extraction was evaluated using liquid chromatography coupled to chemical vapor generation and determination by inductively coupled plasma mass spectrometry. The proposed method was applied for mercury analysis in shark, croaker and tuna fish tissues. Certified reference materials were used to check accuracy and the agreement was better than 95%. The characteristic mass was 60 pg and method limits of detection were 5, 1 and 1 ng g - 1 for organic, inorganic and total mercury, respectively. With the proposed method it was possible to analyze up to 2, 2 and 6 samples per hour for organic, inorganic and total Hg determination, respectively.

  8. An Epidemiological Study of Mercury Sensitization

    Directory of Open Access Journals (Sweden)

    Kazuhiro Sato

    1997-01-01

    Full Text Available Mercury sensitization has been historically in question and may be related to recent increases of type I allergic diseases. To clarify the epidemiological factors of mercury sensitization, we investigated factors relating to mercury sensitization in 215 medical students. Their allergic symptoms, family histories and lifestyles were studied by questionnaire. Patch tests were performed with HgCI2 (0.05% aq. and NiS04 (5% aq.. Anti- Dermatophagoides and anti-Crypfomeria pollen IgE antibodies in sera were also measured. Urinary mercury concentrations were measured in 25 mercury sensitized and 44 non-sensitized subjects (controls. Hair mercury concentrations were also measured in 19 sensitized and 22 non-sensitized subjects. While the positive rate of nickel was 6.0% (13/215, that of mercury was high (13.0%; 28/215. The subjects' individual histories of allergic rhinitis, eczema, urticaria and allergic conjunctivitis were significantly associated with family histories of these conditions (P<0.01, P<0.005 and P<0.005, respectively, as reported in the literature. However, no allergen- specific antibody positivity or past history of allergic disease was associated with mercury sensitization. Mercury sensitized subjects had experienced eczema caused by cosmetics, shampoos, soaps and haircreams significantly more frequently (P<0.05. The history of mercurochrome usage was not associated with mercury sensitization. The number of teeth treated with metals in mercury sensitized subjects was significantly higher than that in the control group (6.8±4.3 vs 4.8±1; P<0.05. There were significant differences in urinary mercury concentrations (specific gravity adjusted levels between mercury sensitized subjects and non-sensitized subjects (2.0±0.9 and 1.3±0.6 (xg/L, respectively; P<0.001. There were also significant differences in hair mercury concentrations between mercury sensitized and non-sensitized subjects (2.0±0.9 and 1.2±0.5 μg/g, respectively; P<0

  9. Mercury Phase II Study - Mercury Behavior across the High-Level Waste Evaporator System

    Energy Technology Data Exchange (ETDEWEB)

    Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Jackson, D. G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Shah, H. B. [Savannah River Remediation, LLC., Aiken, SC (United States); Jain, V. [Savannah River Remediation, LLC., Aiken, SC (United States); Occhipinti, J. E. [Savannah River Remediation, LLC., Aiken, SC (United States); Wilmarth, W. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-06-17

    The Mercury Program team’s effort continues to develop more fundamental information concerning mercury behavior across the liquid waste facilities and unit operations. Previously, the team examined the mercury chemistry across salt processing, including the Actinide Removal Process/Modular Caustic Side Solvent Extraction Unit (ARP/MCU), and the Defense Waste Processing Facility (DWPF) flowsheets. This report documents the data and understanding of mercury across the high level waste 2H and 3H evaporator systems.

  10. Assessing Mercury and Methylmercury Bioavailability in Sediment Pore Water Using Mercury-Specific Hydrogels

    Science.gov (United States)

    2015-06-01

    FINAL REPORT Assessing Mercury and Methylmercury Bioavailability in Sediment Pore Water Using Mercury -Specific Hydrogels SERDP Project ER-1771...From - To) 2010-2015 4. TITLE AND SUBTITLE Assessing Mercury and Methylmercury Bioavailability in 5a. CONTRACT NUMBER W912HQ-10-C-0069 Sediment...Using Mercury -Specific DGTs 5b. GRANT NUMBER ER-1771 5c. PROGRAM ELEMENT NUMBER NA 6. AUTHOR(S) Magar, Victor S.*, Steenhaut, Nicholas

  11. Mercury concentrations at a historically mercury-contaminated site in KwaZulu-Natal, South Africa

    CSIR Research Space (South Africa)

    Williams, CR

    2011-02-01

    Full Text Available . Biogeochem., 43:237?257 Barrat GJ, Combrink J (2002) An Assessment of the degree of mercury (Hg) bio-transformation in two river systems following discharges from a mercury recovery plant. Water SA Special Edition: WISA Proceedings 2002 Benoit JM... in mercury and methylmercury biogeochemical cycling and bioaccumulation within shallow estuaries. PhD thesis, University of Maryland, College Park Kim E-H, Mason RP, Porter ET, Soulen HL (2006) The impact of resuspension on sediment mercury dynamics...

  12. Amended Silicated for Mercury Control

    Energy Technology Data Exchange (ETDEWEB)

    James Butz; Thomas Broderick; Craig Turchi

    2006-12-31

    Amended Silicates{trademark}, a powdered, noncarbon mercury-control sorbent, was tested at Duke Energy's Miami Fort Station, Unit 6 during the first quarter of 2006. Unit 6 is a 175-MW boiler with a cold-side electrostatic precipitator (ESP). The plant burns run-of-the-river eastern bituminous coal with typical ash contents ranging from 8-15% and sulfur contents from 1.6-2.6% on an as-received basis. The performance of the Amended Silicates sorbent was compared with that for powdered activated carbon (PAC). The trial began with a period of baseline monitoring during which no sorbent was injected. Sampling during this and subsequent periods indicated mercury capture by the native fly ash was less than 10%. After the baseline period, Amended Silicates sorbent was injected at several different ratios, followed by a 30-day trial at a fixed injection ratio of 5-6 lb/MMACF. After this period, PAC was injected to provide a comparison. Approximately 40% mercury control was achieved for both the Amended Silicates sorbent and PAC at injection ratios of 5-6 lbs/MMACF. Higher injection ratios did not achieve significantly increased removal. Similar removal efficiencies have been reported for PAC injection trials at other plants with cold-side ESPs, most notably for plants using medium to high sulfur coal. Sorbent injection did not detrimentally impact plant operations and testing confirmed that the use of Amended Silicates sorbent does not degrade fly ash quality (unlike PAC). The cost for mercury control using either PAC or Amended Silicates sorbent was estimated to be equivalent if fly ash sales are not a consideration. However, if the plant did sell fly ash, the effective cost for mercury control could more than double if those sales were no longer possible, due to lost by-product sales and additional cost for waste disposal. Accordingly, the use of Amended Silicates sorbent could reduce the overall cost of mercury control by 50% or more versus PAC for locations where

  13. Percolation of cadmium across a mercury film

    International Nuclear Information System (INIS)

    Malek, K.; Gobal, F.

    2003-01-01

    Electrodeposition/dissolution of cadmium onto a film of mercury shows some deviations from the natural liquidity of mercury caused by the reduction of Cd onto it. Percolation and fractal analyzes were done on the surface and the bulk of the mercury film during diffusion of Cd species (atoms). These show that the fractal dimensions of the Cd-inserted mercury film are about 2.11 and 2.54 near the surface of the mercury film and at deeper points inside the film, respectively. The insertion process has a negligible effect on the surface morphology of the mercury film and there is a phase transition in the bulk, as well as a geometrical transition during the Cd-insertion (de-insertion) process. This corresponds to a percolation threshold of about 0.2 mol l -1 Cd content

  14. Mercury in dated Greenland marine sediments

    DEFF Research Database (Denmark)

    Asmund, G.; Nielsen, S.P.

    2000-01-01

    Twenty marine sediment cores from Greenland were analysed for mercury, and dated by the lead-210 method. In general the cores exhibit a mercury profile with higher mercury concentrations in the upper centimetres of the core. The cores were studied by linear regression of In Hg vs, age...... of the sediment for the youngest 100 years. As a rule the mercury decreased with depth in the sediment with various degrees of significance. The increase of the mercury flux during the last 100 years is roughly a doubling. The increase may be of anthropogenic origin as it is restricted to the last 100 years....... In four cores the concentration of manganese was found also to increase in the top layers indicating diagenesis. In the other cases the higher concentrations were not accompanied by higher manganese concentrations. The mercury flux to the sediment surface was generally proportional to the Pb-210 flux...

  15. Human accumulation of mercury in Greenland

    DEFF Research Database (Denmark)

    Johansen, P.; Mulvad, G.; Pedersen, H. S.

    2007-01-01

    In the Arctic, the traditional diet exposes its people to a high intake of mercury especially from marine mammals. To determine whether the mercury is accumulated in humans, we analyzed autopsy samples of liver, kidney and spleen from adult ethnic Greenlanders who died between 1990 and 1994 from...... a wide range of causes, natural and violent. Liver, kidney and spleen samples from between 33 and 71 case subjects were analyzed for total mercury and methylmercury, and liver samples also for selenium. Metal levels in men and women did not differ and were not related to age except in one case, i.......e. for total mercury in liver, where a significant declining concentration with age was observed. The highest total mercury levels were found in kidney followed by liver and spleen. Methylmercury followed the same pattern, but levels were much lower, constituting only 19% of the total mercury concentration...

  16. Acclimation of subsurface microbial communities to mercury

    DEFF Research Database (Denmark)

    de Lipthay, Julia R; Rasmussen, Lasse D; Øregaard, Gunnar

    2008-01-01

    We studied the acclimation to mercury of bacterial communities of different depths from contaminated and noncontaminated floodplain soils. The level of mercury tolerance of the bacterial communities from the contaminated site was higher than those of the reference site. Furthermore, the level...... of mercury tolerance and functional versatility of bacterial communities in contaminated soils initially were higher for surface soil, compared with the deeper soils. However, following new mercury exposure, no differences between bacterial communities were observed, which indicates a high adaptive potential...... of the subsurface communities, possibly due to differences in the availability of mercury. IncP-1 trfA genes were detected in extracted community DNA from all soil depths of the contaminated site, and this finding was correlated to the isolation of four different mercury-resistance plasmids, all belonging...

  17. Thiosulphate assisted phytoextraction of mercury contaminated soils at the Wanshan Mercury Mining District, Southwest China

    Directory of Open Access Journals (Sweden)

    J. Wang

    2013-10-01

    Full Text Available Wanshan, known as the “Mercury Capital” of China, is located in the Southwest of China. Due to the extensive mining and smelting works in the Wanshan area, the local ecosystem has been serious contaminated with mercury. In the present study, a number of soil samples were taken from the Wanshan mercury mining area and the mercury fractionations in soils were analyzed using sequential extraction procedure technique. The obtained results showed that the dominate mercury fractions (represent 95% of total mercury were residual and organic bound mercury. A field trial was conducted in a mercury polluted farmland at the Wanshan mercury mine. Four plant species Brassica juncea Czern. et Coss.var. ASKYC (ASKYC, Brassica juncea Czern. et Coss.var.DPDH (DPDH, Brassica juncea Czern. et Coss.var.CHBD(CHBD, Brassica juncea Czern. et Coss.var.LDZY (LDZY were tested their ability to extract mercury from soil with thiosulphate amendment. The results indicated that the mercury concentration in the roots and shoots of the four plants were significantly increased with thiosulphate treatment. The mercury phytoextraction yield of ASKYC, DPDH, CHBD and LDZY were 92, 526, 294 and 129 g/ha, respectively

  18. Blood Mercury Levels of Zebra Finches Are Heritable: Implications for the Evolution of Mercury Resistance.

    Directory of Open Access Journals (Sweden)

    Kenton A Buck

    Full Text Available Mercury is a ubiquitous metal contaminant that negatively impacts reproduction of wildlife and has many other sub-lethal effects. Songbirds are sensitive bioindicators of mercury toxicity and may suffer population declines as a result of mercury pollution. Current predictions of mercury accumulation and biomagnification often overlook possible genetic variation in mercury uptake and elimination within species and the potential for evolution in affected populations. We conducted a study of dietary mercury exposure in a model songbird species, maintaining a breeding population of zebra finches (Taeniopygia guttata on standardized diets ranging from 0.0-2.4 μg/g methylmercury. We applied a quantitative genetics approach to examine patterns of variation and heritability of mercury accumulation within dietary treatments using a method of mixed effects modeling known as the 'animal model'. Significant variation in blood mercury accumulation existed within each treatment for birds exposed at the same dietary level; moreover, this variation was highly repeatable for individuals. We observed substantial genetic variation in blood mercury accumulation for birds exposed at intermediate dietary concentrations. Taken together, this is evidence that genetic variation for factors affecting blood mercury accumulation could be acted on by selection. If similar heritability for mercury accumulation exists in wild populations, selection could result in genetic differentiation for populations in contaminated locations, with possible consequences for mercury biomagnification in food webs.

  19. Radioactive mercury distribution in biological fluids and excretion in human subjects after inhalation of mercury vapor

    International Nuclear Information System (INIS)

    Cherian, M.G.; Hursh, J.B.; Clarkson, T.W.; Allen, J.

    1978-01-01

    The distribution of mercury in red blood cells (RBCs) and plasma, and its excretion in urine and feces are described in five human subjects during the first 7 days following inhalation of radioactive mercury vapor. A major portion (98%) of radioactive mercury in whole blood is initially accumulated in the RBCs and is transferred partly to the plasma compartment until the ratio of mercury in RBCs to plasma is about 2 within 20 h. The cumulative urinary and fecal excretion of mercury for 7 days is about 11.6% of the retained dose, and is closely related to the percent decline in body burden of mercury. There is little correlation between either the urinary excretion and plasma radioactivity of mercury, or the specific activities of urine and plasma mercury, suggesting a mechanism other than a direct glomerular filtration involved in the urinary excretion of recently exposed mercury. These studies suggest that blood mercury levels can be used as an index of recent exposure, while urinary levels may be an index of renal concentration of mercury. However, there is no reliable index for mercury concentration in the brain

  20. Thiosulphate assisted phytoextraction of mercury contaminated soils at the Wanshan Mercury Mining District, Southwest China

    Directory of Open Access Journals (Sweden)

    J Wang

    2013-10-01

    Full Text Available Wanshan, known as the “Mercury Capital” of China, is located in the Southwest of China. Due to the extensive mining and smelting works in the Wanshan area, the local ecosystem has been serious contaminated with mercury. In the present study, a number of soil samples were taken from the Wanshan mercury mining area and the mercury fractionations in soils were analyzed using sequential extraction procedure technique. The obtained results showed that the dominate mercury fractions (represent 95% of total mercury were residual and organic bound mercury. A field trial was conducted in a mercury polluted farmland at the Wanshan mercury mine. Four plant species Brassica juncea Czern. et Coss.var. ASKYC (ASKYC, Brassica juncea Czern. et Coss.var.DPDH (DPDH, Brassica juncea Czern. et Coss.var.CHBD(CHBD, Brassica juncea Czern. et Coss.var.LDZY (LDZY were tested their ability to extract mercury from soil with thiosulphate amendment. The results indicated that the mercury concentration in the roots and shoots of the four plants were significantly increased with thiosulphate treatment. The mercury phytoextraction yield of ASKYC, DPDH, CHBD and LDZY were 92, 526, 294 and 129 g/ha, respectively.

  1. STRESS SENSITIVITY OF MERCURY INJECTION MEASUREMENTS

    OpenAIRE

    Guise, P; Grattoni, C; Allshorn, S; Fisher, QJ; Schiffer, A

    2017-01-01

    Many petrophysical properties (e.g. permeability, electrical resistivity etc.) of tight rocks are very stress sensitive. However, most mercury injection measurements are made using an instrument that does not apply a confining pressure to the samples. Here we further explore the implications of the use and analysis of data from mercury injection porosimetry or mercury capillary pressure measurements (MICP). Two particular aspects will be discussed. First, the effective stress acting on sample...

  2. Mercury in polar bears from Alaska

    Energy Technology Data Exchange (ETDEWEB)

    Lentfer, J.W.; Galster, W.A.

    1987-04-01

    Alaskan polar bear (Ursus maritimus) muscle and liver samples collected in 1972 were analyzed for total mercury. Bears north of Alaska had more mercury than bears west of Alaska. The only difference between young and adult animals was in the northern area where adults had more mercury in liver tissue than young animals. Levels were probably not high enough to be a serious threat to bears.

  3. Process for removing mercury from aqueous solutions

    Science.gov (United States)

    Googin, John M.; Napier, John M.; Makarewicz, Mark A.; Meredith, Paul F.

    1986-01-01

    A process for removing mercury from water to a level not greater than two parts per billion wherein an anion exchange material that is insoluble in water is contacted first with a sulfide containing compound and second with a compound containing a bivalent metal ion forming an insoluble metal sulfide. To this treated exchange material is contacted water containing mercury. The water containing not more than two parts per billion of mercury is separated from the exchange material.

  4. Surface composition of Mercury from reflectance spectrophotometry

    Science.gov (United States)

    Vilas, Faith

    1988-01-01

    The controversies surrounding the existing spectra of Mercury are discussed together with the various implications for interpretations of Mercury's surface composition. Special attention is given to the basic procedure used for reducing reflectance spectrophotometry data, the factors that must be accounted for in the reduction of these data, and the methodology for defining the portion of the surface contributing the greatest amount of light to an individual spectrum. The application of these methodologies to Mercury's spectra is presented.

  5. 78 FR 68021 - Notice of Affirmation of Addition of a Treatment Schedule for Methyl Bromide Fumigation of...

    Science.gov (United States)

    2013-11-13

    ...] Notice of Affirmation of Addition of a Treatment Schedule for Methyl Bromide Fumigation of Blueberries... Treatment Manual a treatment schedule for methyl bromide fumigation of blueberries for Mediterranean fruit... notice. We also determined that the ongoing trade of blueberries would be adversely impacted unless the...

  6. Once-daily glycopyrronium bromide (Seebri Breezhaler(®)) for the treatment of chronic obstructive pulmonary disease (COPD)

    DEFF Research Database (Denmark)

    Ulrik, Charlotte Suppli

    2015-01-01

    glycopyrronium bromide (Seebri Breezhaler®) is a well-tolerated long-acting anti-muscarinic agent (LAMA) with a fast onset of action. In patients with moderate to severe COPD, glycopyrronium bromide has clinically important effects on level of FEV1, use of relief medication, day-time dyspnea scores, and probably...

  7. Accumulation of mercury in selected plant species grown in soils contaminated with different mercury compounds

    International Nuclear Information System (INIS)

    Su, Yi; Han, Fengxiang; Shiyab, Safwan; Chen, Jian; Monts, David L.

    2007-01-01

    The objective of our research is to screen and search for suitable plant species for phyto-remediation of mercury-contaminated soil. Currently our effort is specifically focused on mercury removal from the U.S. Department of Energy (DOE) sites, where mercury contamination is a major concern. In order to cost effectively implement mercury remediation efforts, it is necessary now to obtain an improved understanding of biological means of removing mercury and mercury compounds.. Phyto-remediation is a technology that uses various plants to degrade, extract, contain, or immobilize contaminants from soil and water. In particular, phyto-extraction is the uptake of contaminants by plant roots and translocation within the plants to shoots or leaves. Contaminants are generally removed by harvesting the plants. We have investigated phyto-extraction of mercury from contaminated soil by using some of the known metal-accumulating plants since no natural plant species with mercury hyper-accumulating properties has yet been identified. Different natural plant species have been studied for mercury uptake, accumulation, toxicity and overall mercury removal efficiency. Various mercury compounds, such as HgS, HgCl 2 , and Hg(NO 3 ) 2 , were used as contaminant sources. Different types of soil were examined and chosen for phyto-remediation experiments. We have applied microscopy and diffuse reflectance spectrometry as well as conventional analytical chemistry to monitor the phyto-remediation processes of mercury uptake, translocation and accumulation, and the physiological impact of mercury contaminants on selected plant species. Our results indicate that certain plant species, such as beard grass (Polypogon monospeliensis), accumulated a very limited amount of mercury in the shoots ( 2 powder, respectively; no visual stress symptoms were observed. We also studied mercury phyto-remediation using aged soils that contained HgS, HgCl 2 , or Hg(NO 3 ) 2 . We have found that up to hundreds

  8. The Messenger Mission to Mercury

    CERN Document Server

    Domingue, D. L

    2007-01-01

    NASA’s MESSENGER mission, launched on 3 August, 2004 is the seventh mission in the Discovery series. MESSENGER encounters the planet Mercury four times, culminating with an insertion into orbit on 18 March 2011. It carries a comprehensive package of geophysical, geological, geochemical, and space environment experiments to complete the complex investigations of this solar-system end member, which begun with Mariner 10. The articles in this book, written by the experts in each area of the MESSENGER mission, describe the mission, spacecraft, scientific objectives, and payload. The book is of interest to all potential users of the data returned by the MESSENGER mission, to those studying the nature of the planet Mercury, and by all those interested in the design and implementation of planetary exploration missions.

  9. Augustus as Mercury at last

    Directory of Open Access Journals (Sweden)

    Paulo Martins

    2017-07-01

    Full Text Available My purpose in this paper is to investigate and to analyse the representation of Augustus as Mercury, and what this association may suggest and mean to the Romans from both the urbs and the prouinciae, focusing the epigraphy, the numismatic, and the literature. Furthermore, I review three researches that someway work this problem: Bandinelli, Zanker and Martins. Even though the associations between divinities and rulers were very common – Augustus represented as Apollo, Jupiter or Neptune; Tiberius as Apollo; Claudius as Jupiter; or Commodus as Hercules –, the discussion on the relationship between Augustus and Mercury is very rare in recent bibliography. The latest relevant research on this subject dates back to the first half of the twentieth century. Chittenden’s work on numismatic and Grether’s article on epigraphy are both very important. Thus, new evidences must be considered, so that we can further investigate these representations in the Roman world.

  10. Mercury dosing solutions for fluorescent lamps

    Energy Technology Data Exchange (ETDEWEB)

    Corazza, A; Boffito, C [SAES Getters S.p.A., Viale Italia 77, Lainate (MI) 20020 (Italy)], E-mail: alessio_corazza@saes-group.com

    2008-07-21

    A review of the different technologies used to dose mercury in fluorescent lamps is presented. Conventional liquid mercury dosing is gradually being replaced with more reliable and environmentally friendly solutions that enable a significant reduction of the amount of mercury introduced in the lamp, so as to cope with more stringent regulations issued to minimize the environmental impact of exhausted lamps. This paper will review the most advanced novel methods to assure an accurate and fine dosing of mercury in fluorescent lamps, especially focusing on solutions based on the use of solid alloys.

  11. Sorbents for mercury removal from flue gas

    Energy Technology Data Exchange (ETDEWEB)

    Granite, Evan J.; Hargis, Richard A.; Pennline, Henry W.

    1998-01-01

    A review of the various promoters and sorbents examined for the removal of mercury from flue gas is presented. Commercial sorbent processes are described along with the chemistry of the various sorbent-mercury interactions. Novel sorbents for removing mercury from flue gas are suggested. Since activated carbons are expensive, alternate sorbents and/or improved activated carbons are needed. Because of their lower cost, sorbent development work can focus on base metal oxides and halides. Additionally, the long-term sequestration of the mercury on the sorbent needs to be addressed. Contacting methods between the flue gas and the sorbent also merit investigation.

  12. Risk assessment of mercury contaminated sites

    International Nuclear Information System (INIS)

    Hempel, M.

    1993-01-01

    At two sites, highly contaminated with mercury, risk assessment was executed. Methods were developed to determine organomercury compounds in water, air and soil. Toxicity tests demonstrated the high toxicity of organomercury compounds compared to inorganic mercury. Besides highly toxic methylmercury, ethylmercury was found in soils close to a chemical plant in Marktredwitz. In ultrafiltration-experiments mercury showed great affinity to high molecular substances in water. Lysimeter-experiments proved, that organomercury compounds are adsorbed and transformed to inorganic and elemental mercury. (orig.) [de

  13. Alkaline sorbent injection for mercury control

    Science.gov (United States)

    Madden, Deborah A.; Holmes, Michael J.

    2002-01-01

    A mercury removal system for removing mercury from combustion flue gases is provided in which alkaline sorbents at generally extremely low stoichiometric molar ratios of alkaline earth or an alkali metal to sulfur of less than 1.0 are injected into a power plant system at one or more locations to remove at least between about 40% and 60% of the mercury content from combustion flue gases. Small amounts of alkaline sorbents are injected into the flue gas stream at a relatively low rate. A particulate filter is used to remove mercury-containing particles downstream of each injection point used in the power plant system.

  14. Apparatus for isotopic alteration of mercury vapor

    Science.gov (United States)

    Grossman, Mark W.; George, William A.; Marcucci, Rudolph V.

    1988-01-01

    An apparatus for enriching the isotopic Hg content of mercury is provided. The apparatus includes a reactor, a low pressure electric discharge lamp containing a fill including mercury and an inert gas. A filter is arranged concentrically around the lamp. In a preferred embodiment, constant mercury pressure is maintained in the filter by means of a water-cooled tube that depends from it, the tube having a drop of mercury disposed in it. The reactor is arranged around the filter, whereby radiation from said lamp passes through the filter and into said reactor. The lamp, the filter and the reactor are formed of a material which is transparent to ultraviolet light.

  15. Identification of elemental mercury in the subsurface

    Science.gov (United States)

    Jackson, Dennis G

    2015-01-06

    An apparatus and process is provided for detecting elemental mercury in soil. A sacrificial electrode of aluminum is inserted below ground to a desired location using direct-push/cone-penetrometer based equipment. The insertion process removes any oxides or previously found mercury from the electrode surface. Any mercury present adjacent the electrode can be detected using a voltmeter which indicates the presence or absence of mercury. Upon repositioning the electrode within the soil, a fresh surface of the aluminum electrode is created allowing additional new measurements.

  16. Coal fired flue gas mercury emission controls

    International Nuclear Information System (INIS)

    Wu, Jiang; Pan, Weiguo; Cao, Yan; Pan, Weiping

    2015-01-01

    Mercury (Hg) is one of the most toxic heavy metals, harmful to both the environment and human health. Hg is released into the atmosphere from natural and anthropogenic sources and its emission control has caused much concern. This book introduces readers to Hg pollution from natural and anthropogenic sources and systematically describes coal-fired flue gas mercury emission control in industry, especially from coal-fired power stations. Mercury emission control theory and experimental research are demonstrated, including how elemental mercury is oxidized into oxidized mercury and the effect of flue gas contents on the mercury speciation transformation process. Mercury emission control methods, such as existing APCDs (air pollution control devices) at power stations, sorbent injection, additives in coal combustion and photo-catalytic methods are introduced in detail. Lab-scale, pilot-scale and full-scale experimental studies of sorbent injection conducted by the authors are presented systematically, helping researchers and engineers to understand how this approach reduces the mercury emissions in flue gas and to apply the methods in mercury emission control at coal-fired power stations.

  17. Ocular disorders among workers exposed to mercury.

    Science.gov (United States)

    Gabal, M S; Raslan, O A

    1995-01-01

    Mercury vapor exposed workers may show ocular changes, as well as other systems affection. A sample of 84 workers in preparing mercury fulminate were examined for conjunctival corneal and lenticular manifestation of long duration exposure, together with mercury urinary output. Lens changes were found in 50% of the involved workers while keratopathy as recorded in 34.5% of them. No statistically significant association was found between the occurrence of eye lesions and levels of urinary elimination of mercury. These results suggest local absorption of this element is most probably the underlying cause of ocular affection.

  18. Increased mercury emissions from modern dental amalgams.

    Science.gov (United States)

    Bengtsson, Ulf G; Hylander, Lars D

    2017-04-01

    All types of dental amalgams contain mercury, which partly is emitted as mercury vapor. All types of dental amalgams corrode after being placed in the oral cavity. Modern high copper amalgams exhibit two new traits of increased instability. Firstly, when subjected to wear/polishing, droplets rich in mercury are formed on the surface, showing that mercury is not being strongly bonded to the base or alloy metals. Secondly, high copper amalgams emit substantially larger amounts of mercury vapor than the low copper amalgams used before the 1970s. High copper amalgams has been developed with focus on mechanical strength and corrosion resistance, but has been sub-optimized in other aspects, resulting in increased instability and higher emission of mercury vapor. This has not been presented to policy makers and scientists. Both low and high copper amalgams undergo a transformation process for several years after placement, resulting in a substantial reduction in mercury content, but there exist no limit for maximum allowed emission of mercury from dental amalgams. These modern high copper amalgams are nowadays totally dominating the European, US and other markets, resulting in significant emissions of mercury, not considered when judging their suitability for dental restoration.

  19. Side effects of mercury in dental amalgam

    Directory of Open Access Journals (Sweden)

    Titiek Berniyanti

    2008-03-01

    Full Text Available Dental amalgam is an alloy composed of mixture of approximately equal parts of elemental liquid mercury and an alloy powder. The popularity of amalgam arises from excellent long term performance, ease of use and low cost. Despite the popularity of dental amalgam as restorative material, there have been concerns regarding the potential adverse health and environmental effects arising from exposure to mercury in amalgam. They have long been believed to be of little significance as contributors to the overall body burden of mercury, because the elemental form of mercury is rapidly consumed in the setting reaction of the restoration. In 1997, 80% of dentist in Indonesia still using amalgam as an alternative material, and 60% of them treat the rest of unused amalgam carelessly. In recent years, the possible environmental and health impact caused by certain routines in dental practice has attracted attention among regulators. As part of point source reduction strategies, the discharge of mercury/amalgam-contaminated wastes has been regulated in a number of countries, even though it has been documented that by adopting appropriate mercury hygiene measures, the impact of amalgam use in dentistry is minimal. The purpose of this paper is to examine on studies that relate mercury levels in human to the presence of dental amalgams. It is concluded that even though mercury used in filling is hazardous, if normal occupational recommendations for proper mercury hygiene routines and source of reduction strategies are followed, no occupational health risk can be assumed.

  20. Observations of Mercury in 1988 and 1989

    International Nuclear Information System (INIS)

    Schmude, R.W. Jr.

    1990-01-01

    A visual study of the planet Mercury was carried out in May 1988 and in April and May 1989. Most of the observations were made with the 35.5-cm telescope at the Texas A ampersand M University Observatory. This report presents drawings and a map of Mercury that covers the longitude range of 195-285 deg. One important finding was that a polarizing filter combined with color filters gives a sharper view of the planet. It is also concluded that high-resolution images of Mercury's terminator, either as seen from the earth or with the Hubble Space Telescope, can provide information about Mercury's topography. 10 refs

  1. Phytoremediation of Ionic and Methyl Mercury Pollution

    Energy Technology Data Exchange (ETDEWEB)

    Meagher, Richard B.

    2005-06-01

    Phytoremediation is defined as the use of plants to extract, resist, detoxify, and/or sequester toxic environmental pollutants. The long-term goal of the proposed research is to develop and test highly productive, field-adapted plant species that have been engineered for the phytoremediation of mercury. A variety of different genes, which should enable plants to clean mercury polluted sites are being tested as tools for mercury phytoremediation, first in model laboratory plants and then in potential field species. Several of these genes have already been shown to enhance mercury phytoremediation. Mercury pollution is a serious, world-wide problem affecting the health of human and wildlife populations. Environmentally, the most serious mercury threat is the production of methylmercury (CH3Hg+) by native bacteria at mercury contaminated wetland sites. Methylmercury is inherently more toxic than metallic (Hg(0)) or ionic (Hg(II)) mercury, and because methylmercury is prolifically biomagnified up the food chain, it poses the most immediate danger to animal populations. We have successfully engineered two model plants, Arabidopsis and tobacco, to use the bacterial merB gene to convert methylmercury to less toxic ionic mercury and to use the bacterial merA gene to further detoxify ionic mercury to the least toxic form of mercury, metallic mercury. Plants expressing both MerA and MerB proteins detoxify methylmercury in two steps to the metallic form. These plants germinate, grow, and set seed at normal growth rates on levels of methylmercury or ionic mercury that are lethal to normal plants. Our newest efforts involve engineering plants with several additional bacterial and plant genes that allow for higher levels of mercury resistance and mercury hyperaccumulation. The potential for these plants to hyperaccumulate mercury was further advanced by developing constitutive, aboveground, and root-specific gene expression systems. Our current strategy is to engineer plants to

  2. EDITORIAL: Mercury-free discharges for lighting

    Science.gov (United States)

    Haverlag, M.

    2007-07-01

    This special Cluster of articles in Journal of Physics D: Applied Physics covers the subject of mercury-free discharges that are being investigated by different light source researchers, as an alternative to existing mercury-containing lamps. The main driving force to move away from mercury-containing discharge light sources is connected to the environmentally unfriendly nature of mercury. After inhalation or direct contact, severe mercury exposure can lead to damage to human brain cells, the kidneys, the liver and the nervous system. For this reason, the use of mercury in products is becoming more and more restricted by different governmental bodies. In the lighting industry, however, many products still make use of mercury, for different reasons. The main reason is that mercury-containing products are, in most cases, more efficient than mercury-free products. For a realistic comparison of the environmental impact, the mercury-contamination due to electricity production must be taken into account, which depends on the type of fuel being used. For an average European fuel-mix, the amount of mercury that is released into the environment is around 29 μg kWh-1. This means that a typical 30 W TL lamp during a lifetime of 20,000 hours will release a total of about 20 mg mercury due to electricity production, which exceeds the total mercury dose in the lamp (more and more of which is being recycled) by a factor of 5-10 for a modern TL lamp. This illustrates that, quite apart from other environmental arguments like increased CO2 production, mercury-free alternatives that use more energy can in fact be detrimental for the total mercury pollution over the lifetime of the lamp. For this reason, the lighting industry has concentrated on lowering the mercury content in lamps as long as no efficient alternatives exist. Nevertheless, new initiatives for HID lamps and fluorescent lamps with more or less equal efficiency are underway, and a number of them are described in this

  3. 76 FR 34700 - Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications...

    Science.gov (United States)

    2011-06-14

    ... format and Microsoft Excel at EPA's Web site: http://www.epa.gov/ozone/mbr/cueinfo.html ; 2. Hard copy... Excel at Docket ID No. EPA-HQ-OAR-2011- 0431. The docket can be accessed at the http://www.regulations.... Section 604(d)(6), as added in 1998, allows EPA to exempt the production and import of methyl bromide from...

  4. 78 FR 32646 - Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications...

    Science.gov (United States)

    2013-05-31

    ... methyl bromide critical use exemption can be obtained in PDF, Microsoft Word, and Microsoft Excel formats... pest infestation and examples of any phytosanitary requirements of foreign markets (e.g., import... requirements of foreign markets (e.g., import requirements of other countries) that may necessitate use of...

  5. Methyl Bromide Measurements in the Taylor Dome M3C1 Ice Core, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — The data set includes methyl bromide (CH3Br) measurements made on air extracted from 70 samples from the Taylor Dome M3C1 ice core. CH3Br was measured in air from...

  6. SYBR safeTMefficiently replaces ethidium bromide in Aspergillus fumigatus gene disruption.

    Science.gov (United States)

    Canela, H M S; Takami, L A; Ferreira, M E S

    2017-02-08

    Invasive aspergillosis is a disease responsible for high mortality rates, caused mainly by Aspergillus fumigatus. The available drugs are limited and this disease continues to occur at an unacceptable frequency. Gene disruption is essential in the search for new drug targets. An efficient protocol for A. fumigatus gene disruption was described but it requires ethidium bromide, a genotoxic agent, for DNA staining. Therefore, the present study tested SYBR safe TM , a non-genotoxic DNA stain, in A. fumigatus gene disruption protocol. The chosen gene was cipC, which has already been disrupted successfully in our laboratory. A deletion cassette was constructed in Saccharomyces cerevisiae and used in A. fumigatus transformation. There was no statistical difference between the tested DNA stains. The success rate of S. cerevisiae transformation was 63.3% for ethidium bromide and 70% for SYBR safe TM . For A. fumigatus gene disruption, the success rate for ethidium bromide was 100 and 97% for SYBR safe TM . In conclusion, SYBR safe TM efficiently replaced ethidium bromide, making this dye a safe and efficient alternative for DNA staining in A. fumigatus gene disruption.

  7. Two Zn and Hg bromide salts based on 1-ethyl-3-methyl ...

    African Journals Online (AJOL)

    Two Zn and Hg bromide salts based on 1-ethyl-3-methyl imidazolium ionic liquid: Ionothermal synthesis, structures and supramolecular organization. ... Both compounds exhibit 3D supramolecular architectures organized by the C-H···Br hydrogen bondings and alkyl-alkyl interactions. KEY WORDS: Crystal structure, ...

  8. EVALUATION OF CONTAINMENT AND CONTROL OPTIONS FOR METHYL BROMIDE IN COMMODITY TREATMENT

    Science.gov (United States)

    The report gives results of an investigation of means for methyl bromide (MeBr) recovery, reuse, and destruction to prevent atmospheric emissions if its limited use were still allowed. (NOTE: MeBr is an ozone-depleting chemical scheduled to be phased out by the Clean Air Act by t...

  9. Comparison of bromide and nitrate transport in the Bainsvlei soil of ...

    African Journals Online (AJOL)

    Bromide is commonly used to simulate the movement of nitrate fertilisers through the soil profile. However, there exists no comparative evaluation of the leaching properties of Br- and NO3-_N under local soil and rainfall conditions at Bloemfontein. The purpose of this work was to conduct a field experiment to evaluate the ...

  10. Combinatorial electrochemistry using metal nanoparticles: from proof-of-concept to practical realisation for bromide detection.

    Science.gov (United States)

    Sljukić, Biljana; Baron, Ronan; Salter, Chris; Crossley, Alison; Compton, Richard G

    2007-05-02

    Principles and practical application of combinatorial electrochemistry in search for new electroactive materials in electroanalysis have been explored. Nanoparticles of three different metals: silver, gold and palladium have been independently synthesized on the glassy carbon spherical powder surface by electroless deposition process and characterized using both spectroscopic and electrochemical techniques. These three materials were then combined together onto basal plane pyrolytic graphite electrode surface and the application of the combinatorial approach to find the electrode material for bromide detection as model target analyte was demonstrated. The component electroactive for bromide detection was next identified and it was found that silver nanoparticles were the active ones. A composite electrode based on silver nanoparticle modified glassy carbon powder and epoxy resin was then fabricated and it was found to allow accurate determination of bromide. The electroactivity for the bromide determination of the composite electrode was compared with that of a bulk silver electrode and it was shown that the composite electrode is very efficient with a comparable electroactivity with only a portion of precious metals being used for its construction.

  11. Use of Br-82 and I-131 radionuclides in studies of goitrogenic effects of exogenous bromide

    Czech Academy of Sciences Publication Activity Database

    Pavelka, Stanislav

    2012-01-01

    Roč. 291, č. 2 (2012), s. 379-383 ISSN 0236-5731 R&D Projects: GA ČR(CZ) GA304/08/0256 Institutional research plan: CEZ:AV0Z50110509 Keywords : bromide * goitrogenic effect * iodine radionuclides * thyroid hormone Subject RIV: ED - Physiology Impact factor: 1.467, year: 2012

  12. Radioiodine tracers as useful tools in studies of thyrotoxic effects of exogenous bromide and perchlorate ions

    Czech Academy of Sciences Publication Activity Database

    Pavelka, Stanislav

    2012-01-01

    Roč. 291, č. 2 (2012), s. 405-408 ISSN 0236-5731 R&D Projects: GA ČR(CZ) GA304/08/0256 Institutional research plan: CEZ:AV0Z50110509 Keywords : bromide * perchlorate * radioiodine tracer * thyroid hormone Subject RIV: ED - Physiology Impact factor: 1.467, year: 2012

  13. Effects of intraoperative magnetic resonance imaging on the neuromuscular blockade of vecuronium bromide in neurosurgery

    International Nuclear Information System (INIS)

    Guo Ying; Zhang Hong; Sun Li

    2013-01-01

    The effects of intraoperative magnetic resonance (iMR) imaging on the neuromuscular blockade of vecuronium bromide were investigated in neurosurgery. Fifty patients with American Society of Anesthesiologists grades I-II scheduled for craniotomy operation were divided into two groups (n=25 each) with no difference in demographic data: the iMR imaging group and control group. Train-of-four (TOF) stimulation through an accelerometer was used to monitor onset, maintenance, and recovery of muscle relaxation caused by vecuronium. Vecuronium bromide was intravenously injected after anesthesia induction. The dosage of vecuronium bromide in the iMR imaging group was larger than in the control group, but not significantly. Duration of vecuronium bromide administration and operation time were significantly longer in the iMR imaging group than in the control group. Time from drug discontinuation to operation termination, and to return to neurosurgery intensive care unit were not different. Time taken by first twitch (T 1 ) in response to TOF stimulation to recover by 25%, and muscle relaxant recovery index were significantly greater in the control group than in the iMR imaging group. The body temperature of the patients increased gradually in the iMR imaging group but decreased in the control group. iMR imaging can prolong the operation time, increase the body temperature of the patient, and remarkably shorten the clinical action time and muscle relaxation recovery index of vecuronium. (author)

  14. Nematicidal activity of allyl bromide and dibromo(nitro)methane under laboratory conditions.

    Science.gov (United States)

    Oka, Yuji; Shuker, Shimshon; Tkachi, Nadia

    2016-01-01

    Restrictions on soil fumigants are prompting the development of new compounds for controlling nematodes, other soilborne pathogens and weeds. We evaluated the nematicidal activity of five bromine compounds against Meloidogyne javanica in vitro, and tested the two most effective ones against Pratylenchus penetrans and Xiphinema index in vitro and in soil. Only allyl bromide and dibromo(nitro)methane showed nematicidal activity against M. javanica juveniles in vitro at activity than dibromo(nitro)methane against M. javanica and P. penetrans in soil. Allyl bromide at 40 and 20 mg L(-1) soil eliminated root galls and nematode eggs on tomato roots grown in M. javanica-inoculated loess and sandy soils respectively, showing higher nematicidal activity than 1,3-dichloropropene. No P. penetrans were recovered from soil treated with 80 mg allyl bromide L(-1) soil or 320 mg dibromo(nitro)methane L(-1) soil. Allyl bromide showed high nematicidal activity against all three nematode species, and nematicidal activity of dibromo(nitro)methane was discovered. These compounds could serve as new fumigation nematicides, pending further experiments. © 2015 Society of Chemical Industry.

  15. 77 FR 31564 - Notice of Availability of a Treatment Evaluation Document; Methyl Bromide Fumigation of Cottonseed

    Science.gov (United States)

    2012-05-29

    ... pathogen Fusarium oxysporum f. sp. vasinfectum (FOV). We have prepared a treatment evaluation document that... determined a new methyl bromide fumigation treatment schedule to neutralize the fungal pathogen Fusarium oxysporum f. sp. vasinfectum (FOV) on cottonseed (Gossypium spp.) is effective, and we have determined that...

  16. OZONATION BYPRODUCTS: IDENTIFICATION OF BROMOHYDRINS FROM THE OZONATION OF NATURAL WATERS WITH ENHANCED BROMIDE LEVELS

    Science.gov (United States)

    When ozone is used in the treatment of drinking water, it reacts with both inorganic and organic compounds to form byproducts. f bromide is present, it may be oxidized to hydrobromous acid, which may than react with natural organic matter to form brominated organic compounds. he ...

  17. Impact of high bromide intake in the rat dam on iodine transfer to the sucklings

    Czech Academy of Sciences Publication Activity Database

    Pavelka, Stanislav; Babický, Arnošt; Lener, J.; Vobecký, Miloslav

    2002-01-01

    Roč. 40, č. 7 (2002), s. 1041-1045 ISSN 0278-6915 R&D Projects: GA MZd NJ6109 Institutional research plan: CEZ:AV0Z5011922 Keywords : bromide * iodine * rat Subject RIV: ED - Physiology Impact factor: 1.693, year: 2002

  18. Comparing copper sulfate, diquat bromide, formalin, and hydrogen peroxide treatments on channel catfish eggs

    Science.gov (United States)

    Reduced fish egg survival is often associated with fungal infestation (Saprolegnia spp.) of the eggs. Chemical treatments have been used to limit these infestations on fish eggs and increase survival. The effect of copper sulfate (10 mg/L), diquat bromide (25 mg/L diquat cation), formalin (433 mg/...

  19. Study of the antibacterial and antifungal activities of synthetic benzyl bromides, ketones, and corresponding chalcone derivatives.

    Science.gov (United States)

    Shakhatreh, Muhamad Ali K; Al-Smadi, Mousa L; Khabour, Omar F; Shuaibu, Fatima A; Hussein, Emad I; Alzoubi, Karem H

    2016-01-01

    Several applications of chalcones and their derivatives encouraged researchers to increase their synthesis as an alternative for the treatment of pathogenic bacterial and fungal infections. In the present study, chalcone derivatives were synthesized through cross aldol condensation reaction between 4-( N , N -dimethylamino)benzaldehyde and multiarm aromatic ketones. The multiarm aromatic ketones were synthesized through nucleophilic substitution reaction between 4-hydroxy acetophenone and benzyl bromides. The benzyl bromides, multiarm aromatic ketones, and corresponding chalcone derivatives were evaluated for their activities against eleven clinical pathogenic Gram-positive, Gram-negative bacteria, and three pathogenic fungi by the disk diffusion method. The minimum inhibitory concentration was determined by the microbroth dilution technique. The results of the present study demonstrated that benzyl bromide derivatives have strong antibacterial and antifungal properties as compared to synthetic chalcone derivatives and ketones. Benzyl bromides (1a and 1c) showed high ester activity against Gram-positive bacteria and fungi but moderate activity against Gram-negative bacteria. Therefore, these compounds may be considered as good antibacterial and antifungal drug discovery. However, substituted ketones (2a-b) as well as chalcone derivatives (3a-c) showed no activity against all the tested strains except for ketone (2c), which showed moderate activity against Candida albicans .

  20. Once-daily glycopyrronium bromide, a long-acting muscarinic antagonist, for chronic obstructive pulmonary disease

    DEFF Research Database (Denmark)

    Ulrik, Charlotte Suppli

    2012-01-01

    Long-acting bronchodilators are central in the pharmacological management of patients with chronic obstructive pulmonary disease (COPD). The aim of this systematic review is to provide an overview of the studies evaluating the safety and clinical efficacy of inhaled glycopyrronium bromide, a novel...

  1. Iodine catalyzed and tertiary butyl ammonium bromide promoted p reparation of b enzoxazaphosphininyl phenylboronates

    Directory of Open Access Journals (Sweden)

    K. R. Kishore K. Reddy,

    2009-05-01

    Full Text Available Benzoxazaphosphininyl Phenylboronates were prepared by O-Phosphorylation of potassium salt ofphenylboronic acid with cyclic phosphoromonochloridates in the presence of stoichiometric amount of Iodineand catalytic amount of tertiary butyl ammonium bromide at 50-60 °C in dry toluene.

  2. Rapid Monitoring of Mercury in Air from an Organic Chemical Factory in China Using a Portable Mercury Analyzer

    OpenAIRE

    Yasutake, Akira; Cheng, Jin Ping; Kiyono, Masako; Uraguchi, Shimpei; Liu, Xiaojie; Miura, Kyoko; Yasuda, Yoshiaki; Mashyanov, Nikolay

    2011-01-01

    A chemical factory, using a production technology of acetaldehyde with mercury catalysis, was located southeast of Qingzhen City in Guizhou Province, China. Previous research showed heavy mercury pollution through an extensive downstream area. A current investigation of the mercury distribution in ambient air, soils, and plants suggests that mobile mercury species in soils created elevated mercury concentrations in ambient air and vegetation. Mercury concentrations of up to 600 ng/m3 in air o...

  3. Multiscale geomorphometric modeling of Mercury

    Science.gov (United States)

    Florinsky, I. V.

    2018-02-01

    Topography is one of the key characteristics of a planetary body. Geomorphometry deals with quantitative modeling and analysis of the topographic surface and relationships between topography and other natural components of landscapes. The surface of Mercury is systematically studied by interpretation of images acquired during the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) mission. However, the Mercurian surface is still little explored by methods of geomorphometry. In this paper, we evaluate the Mercury MESSENGER Global DEM MSGR_DEM_USG_SC_I_V02 - a global digital elevation model (DEM) of Mercury with the resolution of 0.015625° - as a source for geomorphometric modeling of this planet. The study was performed at three spatial scales: the global, regional (the Caloris basin), and local (the Pantheon Fossae area) ones. As the initial data, we used three DEMs of these areas with resolutions of 0.25°, 0.0625°, and 0.015625°, correspondingly. The DEMs were extracted from the MESSENGER Global DEM. From the DEMs, we derived digital models of several fundamental morphometric variables, such as: slope gradient, horizontal curvature, vertical curvature, minimal curvature, maximal curvature, catchment area, and dispersive area. The morphometric maps obtained represent peculiarities of the Mercurian topography in different ways, according to the physical and mathematical sense of a particular variable. Geomorphometric models are a rich source of information on the Mercurian surface. These data can be utilized to study evolution and internal structure of the planet, for example, to visualize and quantify regional topographic differences as well as to refine geological boundaries.

  4. Suppression of IL-8 production from airway cells by tiotropium bromide in vitro

    Directory of Open Access Journals (Sweden)

    Suzaki I

    2011-09-01

    Full Text Available Isao Suzaki1, Kazuhito Asano2, Yusuke Shikama3, Taisuke Hamasaki1, Ayako Kanei1, Harumi Suzaki11Department of Otorhinolaryngology, School of Medicine, Showa University, Tokyo, Japan; 2Division of Physiology, School of Nursing and Rehabilitation Sciences, Showa University, Yokohama, Japan; 3Department of Respiratory Diseases, Showa University Northern Yokohama Hospital, Yokohama, JapanBackground: COPD is characterized by persistent and progressive airway inflammation. Although neutrophilic airway inflammation is generally accepted to be a major factor in the pathogenesis of COPD, the influence of the agents used for the treatment of COPD on neutrophil functions such as chemotaxis is not fully understood.Purpose: The present study aimed to examine the influence of tiotropium bromide on the production of interleukin (IL-8 from human airway epithelial cells and lung fibroblasts (LFs after lipopolysaccharide (LPS stimulation in vitro.Methods: BEAS-2B cells, human bronchial epithelial cell line, and LFs, at a concentration of 5 × 105 cells/mL, were stimulated with LPS in the presence of various concentrations of tiotropium bromide. IL-8 in culture supernatants was examined by enzyme-linked immunosorbent assay (ELISA. IL-8 messenger ribonucleic acid (mRNA expression was examined by real-time polymerase chain reaction. The influence of tiotropium bromide on LPS-induced signaling pathways was also analyzed by examining nuclear factor-kappa (NF-κB activation and signaling protein phosphorylation by ELISA.Results: Tiotropium bromide at >15 pg/mL inhibited IL-8 production from both BEAS-2B cells and LFs after LPS stimulation. Tiotropium bromide also suppressed IL-8 mRNA expression through the inhibition of NF-κB activation and signaling protein, extracellular-signal-regulated kinase 1/2, and c-Jun N-terminal kinase, phosphorylation.Conclusion: The present results strongly suggest that tiotropium bromide exerts the inhibitory effect on neutrophilic

  5. Characterization of soluble bromide measurements and a case study of BrO observations during ARCTAS

    Directory of Open Access Journals (Sweden)

    J. Liao

    2012-02-01

    Full Text Available A focus of the Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS mission was examination of bromine photochemistry in the spring time high latitude troposphere based on aircraft and satellite measurements of bromine oxide (BrO and related species. The NASA DC-8 aircraft utilized a chemical ionization mass spectrometer (CIMS to measure BrO and a mist chamber (MC to measure soluble bromide. We have determined that the MC detection efficiency to molecular bromine (Br2, hypobromous acid (HOBr, bromine oxide (BrO, and hydrogen bromide (HBr as soluble bromide (Br was 0.9±0.1, 1.06+0.30/−0.35, 0.4±0.1, and 0.95±0.1, respectively. These efficiency factors were used to estimate soluble bromide levels along the DC-8 flight track of 17 April 2008 from photochemical calculations constrained to in situ BrO measured by CIMS. During this flight, the highest levels of soluble bromide and BrO were observed and atmospheric conditions were ideal for the space-borne observation of BrO. The good agreement (R2 = 0.76; slope = 0.95; intercept = −3.4 pmol mol−1 between modeled and observed soluble bromide, when BrO was above detection limit (>2 pmol mol−1 under unpolluted conditions (NO<10 pmol mol−1, indicates that the CIMS BrO measurements were consistent with the MC soluble bromide and that a well characterized MC can be used to derive mixing ratios of some reactive bromine compounds. Tropospheric BrO vertical column densities (BrOVCD derived from CIMS BrO observations compare well with BrOTROPVCD from OMI on 17 April 2008.

  6. Serum protein media are important factors in the manual hexadimethrine bromide (polybrene) test, experience in China.

    Science.gov (United States)

    Liu, Feng; Hu, Li-Hua

    2005-02-01

    The use of the manual hexadimethrine bromide (polybrene) test in routine cross-matching after accurately detecting cell grouping and irregular antibodies is prevalent in China. This article reports the importance of serum protein mediums in the performance of the manual hexadimethrine bromide test. Blood group O red blood cells and Blood group AB and Rh positive serum were collected at random from healthy blood donators, IgG anti-D serum separated from pregnant woman, then tested with each other by the manual hexadimethrine bromide methods in routine tests and some designed corresponding tests with IgG, IgM anti-D monoclonal diagnostic reagents and some serum protein components. Red blood cells that were adjusted to 3-5% suspension by normal saline then only added in 0.7 ml low ionic medium (LIM) and two drops of polybrene solution adhere to the surface of test tubes' bottom when centrifuged, so it was difficult to perform the next approach, but the adherence disappeared when red blood cells' concentrations exceeded 20-30%. Rh positive red blood cells coated by anti-D have the same phenomenon. This adherence can be prevented by serum medium diluted from 1:128 to 1:1024 times by normal saline and hemoglobin medium diluted from 1:32 to 1:128 times, but not by albumin or immunoglobulin medium. The denary logarithm values of the greatest inhibited dilutions of serum and hemoglobin elution between antibody sensitizing red blood cells and the same pre-sensitizing red blood cells tests were no significant difference (P value > 0.05). The whole serum or serum protein mediums are important factors that can influence successfully performance of the manual hexadimethrine bromide test. So appliance of the manual hexadimethrine bromide test to immunohematology laboratory, such as when performing titrations of serum or plasma, or when testing eluates for antibody activity, this adherence must be considered.

  7. Kinetics of Chlorination of Benzophenone-3 in the Presence of Bromide and Ammonia.

    Science.gov (United States)

    Abdallah, Pamela; Deborde, Marie; Dossier Berne, Florence; Karpel Vel Leitner, Nathalie

    2015-12-15

    The aim of this study was to assess the impact of chlorination on the degradation of one of the most commonly used UV filters (benzophenone-3 (BP-3)) and the effects of bromide and ammonia on the kinetics of BP-3 elimination. Bromide and ammonia are rapidly converted to bromine and chloramines during chlorination. At first, the rate constants of chlorine, bromine and monochloramine with BP-3 were determined at various pH levels. BP-3 was found to react rapidly with chlorine and bromine, with values of apparent second order rate constants equal to 1.25(±0.14) × 10(3) M(-1)·s(-1) and 4.04(±0.54) × 10(6) M(-1)·s(-1) at pH 8.5 for kChlorine/BP-3 and kBromine/BP-3, respectively, whereas low monochloramine reactivity was observed (kNH2Cl/BP-3 = 0.112 M(-1)·s(-1)). To assess the impact of the inorganic content of water on BP-3 degradation, chlorination experiments with different added concentrations of bromide and/or ammonia were conducted. Under these conditions, BP-3 degradation was found to be enhanced in the presence of bromide due to the formation of bromine, whereas it was inhibited in the presence of ammonia. However, the results obtained were pH dependent. Finally, a kinetic model considering 18 reactions was developed using Copasi to estimate BP-3 degradation during chlorination in the presence of bromide and ammonia.

  8. Maternal transfer of mercury to songbird eggs.

    Science.gov (United States)

    Ackerman, Joshua T; Hartman, C Alex; Herzog, Mark P

    2017-11-01

    We evaluated the maternal transfer of mercury to eggs in songbirds, determined whether this relationship differed between songbird species, and developed equations for predicting mercury concentrations in eggs from maternal blood. We sampled blood and feathers from 44 house wren (Troglodytes aedon) and 34 tree swallow (Tachycineta bicolor) mothers and collected their full clutches (n = 476 eggs) within 3 days of clutch completion. Additionally, we sampled blood and feathers from 53 tree swallow mothers and randomly collected one egg from their clutches (n = 53 eggs) during mid to late incubation (6-10 days incubated) to evaluate whether the relationship varied with the timing of sampling the mother's blood. Mercury concentrations in eggs were positively correlated with mercury concentrations in maternal blood sampled at (1) the time of clutch completion for both house wrens (R 2  = 0.97) and tree swallows (R 2  = 0.97) and (2) during mid to late incubation for tree swallows (R 2  = 0.71). The relationship between mercury concentrations in eggs and maternal blood did not differ with the stage of incubation when maternal blood was sampled. Importantly, the proportion of mercury transferred from mothers to their eggs decreased substantially with increasing blood mercury concentrations in tree swallows, but increased slightly with increasing blood mercury concentrations in house wrens. Additionally, the proportion of mercury transferred to eggs at the same maternal blood mercury concentration differed between species. Specifically, tree swallow mothers transferred 17%-107% more mercury to their eggs than house wren mothers over the observed mercury concentrations in maternal blood (0.15-1.92 μg/g ww). In contrast, mercury concentrations in eggs were not correlated with those in maternal feathers and, likewise, mercury concentrations in maternal blood were not correlated with those in feathers (all R 2  mercury concentrations from maternal blood to eggs

  9. Recovery of Mercury From Contaminated Liquid Wastes

    International Nuclear Information System (INIS)

    1998-01-01

    The Base Contract program emphasized the manufacture and testing of superior sorbents for mercury removal, testing of the sorption process at a DOE site, and determination of the regeneration conditions in the laboratory. During this project, ADA Technologies, Inc. demonstrated the following key elements of a successful regenerable mercury sorption process: (1) sorbents that have a high capacity for dissolved, ionic mercury; (2) removal of ionic mercury at greater than 99% efficiency; and (3) thermal regeneration of the spent sorbent. ADA's process is based on the highly efficient and selective sorption of mercury by noble metals. Contaminated liquid flows through two packed columns that contain microporous sorbent particles on which a noble metal has been finely dispersed. A third column is held in reserve. When the sorbent is loaded with mercury to the point of breakthrough at the outlet of the second column, the first column is taken off-line and the flow of contaminated liquid is switched to the second and third columns. The spent column is regenerated by heating. A small flow of purge gas carries the desorbed mercury to a capture unit where the liquid mercury is recovered. Laboratory-scale tests with mercuric chloride solutions demonstrated the sorbents' ability to remove mercury from contaminated wastewater. Isotherms on surrogate wastes from DOE's Y-12 Plant in Oak Ridge, Tennessee showed greater than 99.9% mercury removal. Laboratory- and pilot-scale tests on actual Y-12 Plant wastes were also successful. Mercury concentrations were reduced to less than 1 ppt from a starting concentration of 1,000 ppt. The treatment objective was 50 ppt. The sorption unit showed 10 ppt discharge after six months. Laboratory-scale tests demonstrated the feasibility of sorbent regeneration. Results show that sorption behavior is not affected after four cycles

  10. Worldwide trend of atmospheric mercury since 1995

    Directory of Open Access Journals (Sweden)

    F. Slemr

    2011-05-01

    Full Text Available Concern about the adverse effects of mercury on human health and ecosystems has led to tightening emission controls since the mid 1980s. But the resulting mercury emissions reductions in many parts of the world are believed to be offset or even surpassed by the increasing emissions in rapidly industrializing countries. Consequently, concentrations of atmospheric mercury are expected to remain roughly constant. Here we show that the worldwide atmospheric mercury concentrations have decreased by about 20 to 38 % since 1996 as indicated by long-term monitoring at stations in the Southern and Northern Hemispheres combined with intermittent measurements of latitudinal distribution over the Atlantic Ocean. The total reduction of the atmospheric mercury burden of this magnitude within 14 years is unusually large among most atmospheric trace gases and is at odds with the current mercury emission inventories with nearly constant anthropogenic emissions over this period. This suggests a major shift in the biogeochemical cycle of mercury including oceans and soil reservoirs. Decreasing reemissions from the legacy of historical mercury emissions are the most likely explanation for this decline since the hypothesis of an accelerated oxidation rate of elemental mercury in the atmosphere is not supported by the observed trends of other trace gases. Acidification of oceans, climate change, excess nutrient input and pollution may also contribute by their impact on the biogeochemistry of ocean and soils. Consequently, models of the atmospheric mercury cycle have to include soil and ocean mercury pools and their dynamics to be able to make projections of future trends.

  11. Mercury Methylation and Detoxification by Novel Microorganisms in Mercury Enriched Mesothermal Springs

    Science.gov (United States)

    Gionfriddo, C. M.; Krabbenhoft, D. P.; Stott, M.; Wick, R. R.; Schultz, M. B.; Holt, K. E.; Moreau, J. W.

    2015-12-01

    Hot springs and fumaroles release significant quantities of aqueous and gaseous mercury into the environment. Yet few studies have looked at the microbial underpinnings of mercury transformations in geothermal settings. Recent advancements in culture-independent molecular techniques, such as ultra-high-throughput sequencing, allow us to delve deeply into the functional and phylogenetic make-up of these extreme environments. Here we present results from deep metagenomic sequencing of geothermal microbial communities cycling mercury, focussing on the connections between putative metabolisms and mercury methylation, and the evolution of the mer-operon. Presented are data from two adjacent, acidic (pHNew Zealand), extremely enriched in total mercury (>1000 ng L-1), and varying methylmercury concentrations (1-10 ng L-1). Microbial communities of both springs are dominated by mercury resistant acidophilic, sulfur- and iron-cycling microbes: Acidithiobacillus, Thiomonas, and Thermoplasma. Mercury methylation genes (hgcAB) were only detected in the cooler spring (ΔT~10 °C), with an order of magnitude greater methylmercury (10 ng L-1). The hgcAB genes have no known closest relatives (40°C), and methylmercury concentration. We conclude that the relative amount of mercury methylation in each hot spring is controlled by the presence of methylating bacteria and archaea, the release of bioavailable mercury species from sulfide minerals, counterbalanced by microbial mercury demethylation and reduction and mercury sulfide mineralization.

  12. Mercury rising : mercury emissions from Ontario Power Generation's coal-fired plants

    International Nuclear Information System (INIS)

    Rang, S.

    2004-09-01

    Ontario Power Generation (OPG) operates 5 coal-fired power plants which are the largest single source of mercury emissions in Ontario. Mercury is a persistent, bioaccumulative neurotoxin which is considered toxic under the Canadian Environmental Protection Act. This report examines the health and environmental impacts of mercury, and the trends for mercury emission in Ontario. In 2002, the 5 coal-fired plants emitted 527 kg of mercury into the atmosphere and contributed 39 per cent of the total amount of mercury emitted into the air. While many other sectors have reduced their mercury emissions since 1988, Ontario's coal-fired plants have lagged behind and have actually increased mercury emissions by 16 per cent since 1988. This paper suggests that phasing out OPG coal-fired plants by 2007 could lead to a 39 per cent reduction in airborne mercury emissions. It would also allow Ontario to achieve the Canada Wide Standard for mercury emissions 3 years early, and would help both Ontario and Canada meet air pollution reduction commitments under international agreements. It was noted that phasing out coal-fired power plants by one-third will help Ontario achieve its goal of a 90 per cent reduction in mercury emissions by 2010. It was suggested that alternative power sources can offer a wide range of environmental advantages. 16 refs., 3 tabs., 2 figs

  13. Mercury(II) and methyl mercury speciation on Streptococcus pyogenes loaded Dowex Optipore SD-2

    Energy Technology Data Exchange (ETDEWEB)

    Tuzen, Mustafa, E-mail: m.tuzen@gmail.com [Gaziosmanpasa University, Faculty of Science and Arts, Chemistry Department, 60250 Tokat (Turkey); Uluozlu, Ozgur Dogan [Gaziosmanpasa University, Faculty of Science and Arts, Chemistry Department, 60250 Tokat (Turkey); Karaman, Isa [Gaziosmanpasa University, Faculty of Science and Arts, Biology Department, 60250 Tokat (Turkey); Soylak, Mustafa [Erciyes University, Faculty of Science and Arts, Chemistry Department, 38039 Kayseri (Turkey)

    2009-09-30

    A solid phase extraction procedure based on speciation of mercury(II) and methyl mercury on Streptococcus pyogenes immobilized on Dowex Optipore SD-2 has been established. Selective and sequential elution with 0.1 mol L{sup -1} HCl for methyl mercury and 2 mol L{sup -1} HCl for mercury(II) were performed at pH 8. The determination of mercury levels was performed by cold vapour atomic absorption spectrometry (CVAAS). Optimal analytical conditions including pH, amounts of biosorbent, sample volumes, etc., were investigated. The influences of the some alkaline and earth alkaline ions and some transition metals on the recoveries were also investigated. The capacity of biosorbent for mercury(II) and methyl mercury was 4.8 and 3.4 mg g{sup -1}. The detection limit (3 sigma) of the reagent blank for mercury(II) and methyl mercury was 2.1 and 1.5 ng L{sup -1}. Preconcentration factor was calculated as 25. The relative standard deviations of the procedure were below 7%. The validation of the presented procedure is performed by the analysis of standard reference material (NRCC-DORM 2 Dogfish Muscle). The procedure was successfully applied to the speciation of mercury(II) and methyl mercury in natural water and environmental samples.

  14. Mercury(II) and methyl mercury speciation on Streptococcus pyogenes loaded Dowex Optipore SD-2

    International Nuclear Information System (INIS)

    Tuzen, Mustafa; Uluozlu, Ozgur Dogan; Karaman, Isa; Soylak, Mustafa

    2009-01-01

    A solid phase extraction procedure based on speciation of mercury(II) and methyl mercury on Streptococcus pyogenes immobilized on Dowex Optipore SD-2 has been established. Selective and sequential elution with 0.1 mol L -1 HCl for methyl mercury and 2 mol L -1 HCl for mercury(II) were performed at pH 8. The determination of mercury levels was performed by cold vapour atomic absorption spectrometry (CVAAS). Optimal analytical conditions including pH, amounts of biosorbent, sample volumes, etc., were investigated. The influences of the some alkaline and earth alkaline ions and some transition metals on the recoveries were also investigated. The capacity of biosorbent for mercury(II) and methyl mercury was 4.8 and 3.4 mg g -1 . The detection limit (3 sigma) of the reagent blank for mercury(II) and methyl mercury was 2.1 and 1.5 ng L -1 . Preconcentration factor was calculated as 25. The relative standard deviations of the procedure were below 7%. The validation of the presented procedure is performed by the analysis of standard reference material (NRCC-DORM 2 Dogfish Muscle). The procedure was successfully applied to the speciation of mercury(II) and methyl mercury in natural water and environmental samples.

  15. Human Exposure and Health Effects of Inorganic and Elemental Mercury

    Science.gov (United States)

    Zheng, Wei

    2012-01-01

    Mercury is a toxic and non-essential metal in the human body. Mercury is ubiquitously distributed in the environment, present in natural products, and exists extensively in items encountered in daily life. There are three forms of mercury, i.e., elemental (or metallic) mercury, inorganic mercury compounds, and organic mercury compounds. This review examines the toxicity of elemental mercury and inorganic mercury compounds. Inorganic mercury compounds are water soluble with a bioavailability of 7% to 15% after ingestion; they are also irritants and cause gastrointestinal symptoms. Upon entering the body, inorganic mercury compounds are accumulated mainly in the kidneys and produce kidney damage. In contrast, human exposure to elemental mercury is mainly by inhalation, followed by rapid absorption and distribution in all major organs. Elemental mercury from ingestion is poorly absorbed with a bioavailability of less than 0.01%. The primary target organs of elemental mercury are the brain and kidney. Elemental mercury is lipid soluble and can cross the blood-brain barrier, while inorganic mercury compounds are not lipid soluble, rendering them unable to cross the blood-brain barrier. Elemental mercury may also enter the brain from the nasal cavity through the olfactory pathway. The blood mercury is a useful biomarker after short-term and high-level exposure, whereas the urine mercury is the ideal biomarker for long-term exposure to both elemental and inorganic mercury, and also as a good indicator of body burden. This review discusses the common sources of mercury exposure, skin lightening products containing mercury and mercury release from dental amalgam filling, two issues that happen in daily life, bear significant public health importance, and yet undergo extensive debate on their safety. PMID:23230464

  16. Sexual differences in the excretion of organic and inorganic mercury by methyl mercury-treated rats

    International Nuclear Information System (INIS)

    Thomas, D.J.; Fisher, H.L.; Sumler, M.R.; Mushak, P.; Hall, L.L.

    1987-01-01

    Adult male and female Long Evans rats received 1 mumole of methyl ( 203 Hg) mercuric chloride per kilogram sc. Whole-body retention of mercury and excretion of organic and inorganic mercury in urine and feces were monitored for 98 days after dosing. Females cleared mercury from the body more rapidly than did males. The major route of mercury excretion was feces. By 98 days after dosing, cumulative mercury excretion in feces accounted for about 51% of the dose in males and about 54% of the dose in females. For both sexes, about 33% of the dose was excreted in feces as inorganic mercury. Cumulative excretion of organic mercury in feces accounted for about 18 and 21% of the dose in males and females, respectively. Urinary excretion of mercury was quantitatively a smaller route for mercury clearance but important sexual differences in loss by this route were found. Over the 98-day experimental period, males excreted in urine about 3.2% of the dose and females excreted 7.5%. Cumulative organic Hg excretion in urine accounted for 1.8% of the dose in males and 5.3% of the dose in females. These sexual differences in urinary and fecal excretion of organic and inorganic mercury following methyl mercury treatment were consistent with previous reports of sexual differences in mercury distribution and retention in methyl mercury-treated rats, particularly sexual differences in organic mercury uptake and retention in the kidney. Relationships between body burdens of organic or inorganic Hg and output of these forms of Hg in urine and feces were also found to be influenced by the interval after MeHg treatment and by sex. Relationship between concentration of Hg in liver and feces and in kidney and urine differed for organic and inorganic Hg and depended upon sexual status and interval after MeHg treatment

  17. Mercury Control for Plants Firing Texas Lignite and Equipped with ESP-wet FGD

    Energy Technology Data Exchange (ETDEWEB)

    Katherine Dombrowski

    2009-12-31

    balance-of-plant impacts of the mercury control process, including those associated with ESP performance and fly ash reuse properties. Upon analysis of the project results, the project team identified several areas of interest for further study. Follow-on testing was conducted on Unit 2 in 2009 with the entire unit treated with injected sorbent so that mercury removal across the FGD could be measured and so that other low-ash impact technologies could be evaluated. Three approaches to minimizing ash impacts were tested: (1) injection of 'low ash impact' sorbents, (2) alterations to the injection configuration, and (3) injection of calcium bromide in conjunction with sorbent. These conditions were tested with the goal of identifying the conditions that result in the highest mercury removal while maintaining the sorbent injection at a rate that preserves the beneficial use of ash.

  18. Increased Mercury Bioaccumulation Follows Water Quality Improvement

    Energy Technology Data Exchange (ETDEWEB)

    Bogle, M.A.; Peterson, M.J.; Smith, J.G.; Southworth, G.R.

    1999-09-15

    Changes in physical and chemical characteristics of aquatic habitats made to reduce or eliminate ecological risks can sometimes have unforeseen consequences. Environmental management activities on the U.S. Dept. of Energy reservation in Oak Ridge, Tennessee,have succeeded in improving water quality in streams impacted by discharges fi-om industrial facilities and waste disposal sites. The diversity and abundance of pollution-sensitive components of the benthic macroinvertebrate communities of three streams improved after new waste treatment systems or remedial actions reduced inputs of various toxic chemicals. Two of the streams were known to be mercury-contaminated from historical spills and waste disposal practices. Waterborne mercury concentrations in the third were typical of uncontaminated systems. In each case, concentrations of mercury in fish, or the apparent biological availability of mercury increased over the period during which ecological metrics indicated improved water quality. In the system where waterborne mercury concentrations were at background levels, increased mercury bioaccumulation was probably a result of reduced aqueous selenium concentrations; however, the mechanisms for increased mercury accumulation in the other two streams remain under investigation. In each of the three systems, reduced inputs of metals and inorganic anions was followed by improvements in the health of aquatic invertebrate communities. However, this reduction in risk to aquatic invertebrates was accompanied by increased risk to humans and piscivorous wildlife related to increased mercury concentrations in fish.

  19. Increased Mercury Bioaccumulation Follows Water Quality Improvement

    International Nuclear Information System (INIS)

    Bogle, M.A.; Peterson, M.J.; Smith, J.G.; Southworth, G.R.

    1999-01-01

    Changes in physical and chemical characteristics of aquatic habitats made to reduce or eliminate ecological risks can sometimes have unforeseen consequences. Environmental management activities on the U.S. Dept. of Energy reservation in Oak Ridge, Tennessee,have succeeded in improving water quality in streams impacted by discharges fi-om industrial facilities and waste disposal sites. The diversity and abundance of pollution-sensitive components of the benthic macroinvertebrate communities of three streams improved after new waste treatment systems or remedial actions reduced inputs of various toxic chemicals. Two of the streams were known to be mercury-contaminated from historical spills and waste disposal practices. Waterborne mercury concentrations in the third were typical of uncontaminated systems. In each case, concentrations of mercury in fish, or the apparent biological availability of mercury increased over the period during which ecological metrics indicated improved water quality. In the system where waterborne mercury concentrations were at background levels, increased mercury bioaccumulation was probably a result of reduced aqueous selenium concentrations; however, the mechanisms for increased mercury accumulation in the other two streams remain under investigation. In each of the three systems, reduced inputs of metals and inorganic anions was followed by improvements in the health of aquatic invertebrate communities. However, this reduction in risk to aquatic invertebrates was accompanied by increased risk to humans and piscivorous wildlife related to increased mercury concentrations in fish

  20. A Challenging Case of Acute Mercury Toxicity

    Directory of Open Access Journals (Sweden)

    Ali Nayfeh

    2018-01-01

    Full Text Available Background. Mercury exists in multiple forms: elemental, organic, and inorganic. Its toxic manifestations depend on the type and magnitude of exposure. The role of colonoscopic decompression in acute mercury toxicity is still unclear. We present a case of acute elemental mercury toxicity secondary to mercury ingestion, which markedly improved with colonoscopic decompression. Clinical Case. A 54-year-old male presented to the ED five days after ingesting five ounces (148 cubic centimeters of elemental mercury. Examination was only significant for a distended abdomen. Labs showed elevated serum and urine mercury levels. An abdominal radiograph showed radiopaque material throughout the colon. Succimer and laxatives were initiated. The patient had recurrent bowel movements, and serial radiographs showed interval decrease of mercury in the descending colon with interval increase in the cecum and ascending colon. Colonoscopic decompression was done successfully. The colon was evacuated, and a repeat radiograph showed decreased hyperdense material in the colon. Three months later, a repeat radiograph showed no hyperdense material in the colon. Conclusion. Ingested elemental mercury can be retained in the colon. Although there are no established guidelines for colonoscopic decompression, our patient showed significant improvement. We believe further studies on this subject are needed to guide management practices.

  1. The influence of floodplains on mercury availability

    Energy Technology Data Exchange (ETDEWEB)

    Wallschlaeger, D.; Wilken, R.D. [GKSS Research Center, Geesthacht (Germany). Inst. of Physical and Chemical Analytics

    1997-09-01

    The floodplains of the German river Elbe affect the mercury distribution in the river system in two different ways: they act both as a medium-term sink and as a long-term source. The large amounts of mercury deposited onto the floodplains during annual floodings are first effectively fixed in the soils, rendering them basically unavailable. Sequential extraction experiments reveal that only a small fraction of the mercury (< 3%) is present in available forms, whereas the vast majority is associated with humic substances or present in sulfidic binding forms. After deposition, a small fraction of the total mercury is gradually remobilized into the aqueous phase bound passively to water-soluble humic acids. The availability of mercury in these complexes is still low, since environmental influences such as changes in pH or redox potential and competition with other cations do not cause any mercury liberation. In the next step, reactions in the aqueous phase lead to the formation of the highly available volatile species Hg{sup 0} and dimethylmercury (DMM). Their evaporation gives rise to a strong mercury flux from the floodplains into the atmosphere. Preliminary mass balances indicate that the majority of the deposited mercury stays bound in the floodplain soils, while small amounts are emitted back into the river`s ecosystem. Atmospheric emission is more important as a remobilization pathway than aquatic export.

  2. OCCURENCE OF MERCURY IN PET FOOD

    Directory of Open Access Journals (Sweden)

    M.C. Abete

    2013-02-01

    Full Text Available Mercury levels in 61 complete pet feed containing fish were evaluated. In five samples a mercury content exceeding the maximum residues level (0.4 mg/kg was detected. The statistical evaluation didn’t show a significant correlation between the percentage of fish in feedingstuffs and the contamination level.

  3. Hair mercury measurement in Egyptian autistic children

    African Journals Online (AJOL)

    Farida El-baz

    Abstract Background: A review of medical literature has shown that exposure to mercury, whether organic or inorganic, can give rise to the symptoms and traits defining or commonly found in autism spectrum disorders (ASD). Mercury can cause impairments in social interaction, commu- nication difficulties, and repetitive ...

  4. Terahertz oscillations in mercury cuprate superconductors

    Indian Academy of Sciences (India)

    Abstract. It has been recently reported that the three-dimensional Bose–Einstein con- densation of the quasi-particles is valid for the mercury cuprates at liquid helium tem- perature. In this study, the validity of the interlayer theory in three dimensions has been investigated for optimally oxygen-doped mercury cuprates at the ...

  5. Mercury poisoning | Shamley | South African Medical Journal

    African Journals Online (AJOL)

    The diagnosis of mercury poisoning requires a high index of suspicion. Mercury poisoning in a patient involved in illicit gold extraction is reported and 6 other cases considered. Some of the clinical features and treatment of this condition are discussed. S Afr Med J 1989; 76: 114-116 ...

  6. Mercury soil surveys: a good reconnaissance tool

    Energy Technology Data Exchange (ETDEWEB)

    Stone, C.; Ruscetta, C.A.; Foley, D. (eds.)

    1981-05-01

    Three examples of mercury soil surveys are discussed, along with the gravity data. An excellent correlation was found in southern Arizona between buried structures revealed by gravity and mercury soil surveys. The advantages of the latter over the former as a reconnaissance tool are listed. (MHR)

  7. Intentional intravenous mercury injection | Yudelowitz | South African ...

    African Journals Online (AJOL)

    Intravenous mercury injection is rarely seen, with few documented cases. Treatment strategies are not clearly defined for such cases, although a few options do show benefit. This case report describes a 29-year-old man suffering from bipolar disorder, who presented following self-inflicted intravenous injection of mercury.

  8. Pneumonitis after Inhalation of Mercury Vapours

    Directory of Open Access Journals (Sweden)

    JD Glezos

    2006-01-01

    Full Text Available A 43-year-old man presented to hospital with pneumonia but only after discharge from hospital did he admit to deliberate prior inhalation of mercury. His pulmonary involvement appeared to resolve almost completely with antibiotics and supportive care. Nevertheless, persisting elevated urinary excretion of mercury required two courses of chelation therapy. No serious systemic sequelae were observed.

  9. Recent Advances in Atmospheric Chemistry of Mercury

    Directory of Open Access Journals (Sweden)

    Lin Si

    2018-02-01

    Full Text Available Mercury is one of the most toxic metals and has global importance due to the biomagnification and bioaccumulation of organomercury via the aquatic food web. The physical and chemical transformations of various mercury species in the atmosphere strongly influence their composition, phase, transport characteristics and deposition rate back to the ground. Modeling efforts to assess global cycling of mercury require an accurate understanding of atmospheric mercury chemistry. Yet, there are several key uncertainties precluding accurate modeling of physical and chemical transformations. We focus this article on recent studies (since 2015 on improving our understanding of the atmospheric chemistry of mercury. We discuss recent advances in determining the dominant atmospheric oxidant of elemental mercury (Hg0 and understanding the oxidation reactions of Hg0 by halogen atoms and by nitrate radical (NO3—in the aqueous reduction of oxidized mercury compounds (HgII as well as in the heterogeneous reactions of Hg on atmospheric-relevant surfaces. The need for future research to improve understanding of the fate and transformation of mercury in the atmosphere is also discussed.

  10. Urban artisanal gold shops and mercury emissions

    International Nuclear Information System (INIS)

    Cordy, P.; Veiga, M.; Carrasco, V.H.G.

    2008-01-01

    Artisanal miners in developing countries use mercury amalgamation processes to extract gold. The amalgams are then refined before being sold on to urban gold shops. The amalgams can often contain between 2 to 40 per cent mercury. Unburned amalgams are also often sold directly to gold shops. There are serious health risks for shop employees and nearby populations when the gold is melted and further purified. Studies have shown that mercury concentrations in the ambient air of gold shops often exceeds World Health Organization (WHO) limits by an order of magnitude or more. This study examined the practices and technologies used to refine gold in Latin America and Indonesia. The study compared and contrasted various refining methods and their resulting mercury emissions. Methods of reducing mercury emissions were also investigated, including a filtration system designed to capture 80 per cent of mercury emissions. Barriers to implementing mercury emissions reduction plans were also investigated. It was concluded that the design of urban gold shops must include condensers, fume hoods, and efficient mercury capture systems. 15 refs

  11. Mercury cycling in peatland watersheds. Chapter 11.

    Science.gov (United States)

    Randall K. Kolka; Carl P.J. Mitchell; Jeffrey D. Jeremiason; Neal A. Hines; David F. Grigal; Daniel R. Engstrom; Jill K. Coleman-Wasik; Edward A. Nater; Edward B. Swain; Bruce A. Monson; Jacob A. Fleck; Brian Johnson; James E. Almendinger; Brian A. Branfireun; Patrick L. Brezonik; James B. Cotner

    2011-01-01

    Mercury (Hg) is of great environmental concern due to its transformation into the toxic methylmercury (MeHg) form that bioaccumulates within the food chain and causes health concerns for both humans and wildlife (U.S. Environmental Protection Agency 2002). Mercury can affect neurological development in fetuses and young children. In adults, exposure to Hg can lead to...

  12. Mercury in tropical and subtropical coastal environments

    Science.gov (United States)

    Costa, Monica F.; Landing, William M.; Kehrig, Helena A.; Barletta, Mário; Holmes, Christopher D.; Barrocas, Paulo R. G.; Evers, David C.; Buck, David G.; Vasconcellos, Ana Claudia; Hacon, Sandra S.; Moreira, Josino C.; Malm, Olaf

    2012-01-01

    Anthropogenic activities influence the biogeochemical cycles of mercury, both qualitatively and quantitatively, on a global scale from sources to sinks. Anthropogenic processes that alter the temporal and spatial patterns of sources and cycling processes are changing the impacts of mercury contamination on aquatic biota and humans. Human exposure to mercury is dominated by the consumption of fish and products from aquaculture operations. The risk to society and to ecosystems from mercury contamination is growing, and it is important to monitor these expanding risks. However, the extent and manner to which anthropogenic activities will alter mercury sources and biogeochemical cycling in tropical and sub-tropical coastal environments is poorly understood. Factors as (1) lack of reliable local/regional data; (2) rapidly changing environmental conditions; (3) governmental priorities and; (4) technical actions from supra-national institutions, are some of the obstacles to overcome in mercury cycling research and policy formulation. In the tropics and sub-tropics, research on mercury in the environment is moving from an exploratory “inventory” phase towards more process-oriented studies. Addressing biodiversity conservation and human health issues related to mercury contamination of river basins and tropical coastal environments are an integral part of paragraph 221 paragraph of the United Nations document “The Future We Want” issued in Rio de Janeiro in June 2012. PMID:22901765

  13. Episodic bioavailability of environmental mercury: implications for ...

    African Journals Online (AJOL)

    Perennial wildfires in Africa and other continents contribute an estimated 8 x 105 kg of mercury to the global atmosphere with a residence time of approximately one year. This phenomenon changes the flux of biologically available mercury in natural microbial communities where enzymatic actions, including mercuric ...

  14. Terahertz oscillations in mercury cuprate superconductors

    Indian Academy of Sciences (India)

    It has been recently reported that the three-dimensional Bose–Einstein condensation of the quasi-particles is valid for the mercury cuprates at liquid helium temperature. In this study, the validity of the interlayer theory in three dimensions has been investigated for optimally oxygen-doped mercury cuprates at the temperature ...

  15. Mercury in Thana creek, Bombay harbour

    Digital Repository Service at National Institute of Oceanography (India)

    Zingde, M.D.; Desai, B.N.

    Mercury content of the water column estimated along Thana Creek/Bombay Harbour gave a standing stock of about 77 kg in excess of the expected background. Mercury concentration in sediment from 23 locations which varied from 0.17 to 8.21 ppm (dry...

  16. Urban artisanal gold shops and mercury emissions

    Energy Technology Data Exchange (ETDEWEB)

    Cordy, P.; Veiga, M.; Carrasco, V.H.G. [British Columbia Univ., Vancouver, BC (Canada). Dept. of Mining and Mineral Process Engineering

    2008-07-01

    Artisanal miners in developing countries use mercury amalgamation processes to extract gold. The amalgams are then refined before being sold on to urban gold shops. The amalgams can often contain between 2 to 40 per cent mercury. Unburned amalgams are also often sold directly to gold shops. There are serious health risks for shop employees and nearby populations when the gold is melted and further purified. Studies have shown that mercury concentrations in the ambient air of gold shops often exceeds World Health Organization (WHO) limits by an order of magnitude or more. This study examined the practices and technologies used to refine gold in Latin America and Indonesia. The study compared and contrasted various refining methods and their resulting mercury emissions. Methods of reducing mercury emissions were also investigated, including a filtration system designed to capture 80 per cent of mercury emissions. Barriers to implementing mercury emissions reduction plans were also investigated. It was concluded that the design of urban gold shops must include condensers, fume hoods, and efficient mercury capture systems. 15 refs.

  17. Mercury Sorption onto Malt Spent Rootlets

    Science.gov (United States)

    Manariotis, I. D.; Anagnostopoulos, V.; Karapanagioti, H. K.; Chrysikopoulos, C.

    2011-12-01

    Mercury is a metal of particular concern due to its toxicity even at relatively low concentrations. The maximum permissible level for mercury in drinking water set by the European Union is 0.001 mg/L. Mercury is released into the environment via four principal pathways: (1) natural processes; i.e. a volcanic eruption, (2) incidental to some other activity; i.e. coal burning power plants, (3) accidentally during the manufacture, breakage or disposal of products that have mercury put into them deliberately, and (4) direct use in industrial settings. The present study focuses on the removal of mercury (II) from aqueous solutions via sorption onto Malt Spent Rootlets (MSR). Batch experiments were conducted employing MSR with size ranging from 0.18 to 1 mm. The effects of pH, mercury concentration, contact time, and solid to liquid ratio on mercury sorption onto MSR were investigated. The highest mercury removal from the aqueous phase, of 41%, was observed at pH of 5.

  18. Low dose mercury toxicity and human health.

    Science.gov (United States)

    Zahir, Farhana; Rizwi, Shamim J; Haq, Soghra K; Khan, Rizwan H

    2005-09-01

    Post Minamata incident there has been awareness about mercury toxicity even among the general public. Previous researches contributed a vast amount of data regarding acute mercury exposure, but gradually information about the low dose [Ninomiya, T., Ohmori, H., Hashimoto, K., Tsuruta, K., Ekino, S., 1995. Expansion of methylmercury poisoning outside minamata: an epidemiological study on chronic methylmercury poisoninig outside of Minamata. Environ. Res. 70 (1) 47-50; Lebel, J., Mergler, D., Lucotte, M., Amorim, M., Dolbec, J., Miranda, D., Arantes, G., Rheault, I., Pichet, P., 1996. Evidence of early nervous system dysfunction in Amazonian populations exposed to low-levels of methylmercury. Neurotoxicology 17 (1) 157-167] of mercury toxicity has been trickling in. With mercury contaminating rain-, ground- and sea-water no one is safe. Polluted water leads to mercury laced fish, meat and vegetable. In aquatic environments, inorganic mercury is microbiologically transformed into lipophilic organic compound 'methylmercury'. This transformation makes mercury more prone to biomagnification in food chains. Consequently, populations with traditionally high dietary intake of food originating from fresh or marine environment have highest dietary exposure to mercury. Extensive research done on locals across the globe have already established this, persons who routinely consume fish or a particular species of fish are at an increased risk of methylmercury poisoning. The easy access of the toxicant to man through multiple pathways air, water, food, cosmetic products and even vaccines increase the exposure. Foetus and children are more susceptible towards mercury toxicity. Mothers consuming diet containing mercury pass the toxicant to foetus and to infants through breast milk. Decreased performance in areas of motor function and memory has been reported among children exposed to presumably safe mercury levels. Similarly, disruption of attention, fine motor function and verbal

  19. Effect of salinity on methylation of mercury

    Energy Technology Data Exchange (ETDEWEB)

    Blum, J.E.; Bartha, R.

    1980-09-01

    Monomethyl and dimethylmercury are potent neurotoxins subject to biomagnification in food webs. This fact was tragically demonstrated by the Minamata and Niigata poisoning incidents in Japan in which 168 persons who ate seafood from mercury polluted waters were poisoned, 52 fatally. Shortly after these two incidents, work conducted in freshwater environments demonstrated the microbial conversion of inorganic and phenylmercury compounds to mono- and di-methylmercury. Consideration of some fragmentary evidence from the literature, however, indicates that the rate and the significance of microbial methylation of mercury in freshwater and saltwater environments may not be the same. A demonstrated relationship between mercury methylation rates and water salinity would greatly influence our thinking about mercury pollution effects in marine versus freshwater environments. Since we were unable to locate published reports on this subject, we are investigating the influence of salinity on the rate of mercury methylation in an estuarine sediment.

  20. High activity carbon sorbents for mercury capture

    Directory of Open Access Journals (Sweden)

    Stavropoulos George G.

    2006-01-01

    Full Text Available High efficiency activated carbons have been prepared for removing mercury from gas streams. Starting materials used were petroleum coke, lignite, charcoal and olive seed waste, and were chemically activated with KOH. Produced adsorbents were primarily characterized for their porosity by N2 adsorption at 77 K. Their mercury retention capacity was characterized based on the breakthrough curves. Compared with typical commercial carbons, they have exhibited considerably enhanced mercury adsorption capacity. An attempt has been made to correlate mercury entrapment and pore structure. It has been shown that physical surface area is increased during activation in contrast to the mercury adsorption capacity that initially increases and tends to decrease at latter stages. Desorption of active sites may be responsible for this behavior.

  1. Human accumulation of mercury in Greenland

    DEFF Research Database (Denmark)

    Johansen, Poul; Mulvad, Gert; Pedersen, Henning Sloth

    2007-01-01

    In the Arctic, the traditional diet exposes its people to a high intake of mercury especially from marine mammals. To determine whether the mercury is accumulated in humans, we analyzed autopsy samples of liver, kidney and spleen from adult ethnic Greenlanders who died between 1990 and 1994 from...... a wide range of causes, natural and violent. Liver, kidney and spleen samples from between 33 and 71 case subjects were analyzed for total mercury and methylmercury, and liver samples also for selenium. Metal levels in men and women did not differ and were not related to age except in one case, i...... in liver and spleen and as little as 3% in kidney. In liver selenium was found in surplus to mercury on a molar basis. Mercury concentrations in the liver and kidneys of Greenlanders were elevated compared to levels in the general population in Japan, Korea and several European countries, except...

  2. Autism: a novel form of mercury poisoning.

    Science.gov (United States)

    Bernard, S; Enayati, A; Redwood, L; Roger, H; Binstock, T

    2001-04-01

    Autism is a syndrome characterized by impairments in social relatedness and communication, repetitive behaviors, abnormal movements, and sensory dysfunction. Recent epidemiological studies suggest that autism may affect 1 in 150 US children. Exposure to mercury can cause immune, sensory, neurological, motor, and behavioral dysfunctions similar to traits defining or associated with autism, and the similarities extend to neuroanatomy, neurotransmitters, and biochemistry. Thimerosal, a preservative added to many vaccines, has become a major source of mercury in children who, within their first two years, may have received a quantity of mercury that exceeds safety guidelines. A review of medical literature and US government data suggests that: (i) many cases of idiopathic autism are induced by early mercury exposure from thimerosal; (ii) this type of autism represents an unrecognized mercurial syndrome; and (iii) genetic and non-genetic factors establish a predisposition whereby thimerosal's adverse effects occur only in some children. Copyright 2001 Harcourt Publishers Ltd.

  3. Removal of mercury by adsorption: a review.

    Science.gov (United States)

    Yu, Jin-Gang; Yue, Bao-Yu; Wu, Xiong-Wei; Liu, Qi; Jiao, Fei-Peng; Jiang, Xin-Yu; Chen, Xiao-Qing

    2016-03-01

    Due to natural and production activities, mercury contamination has become one of the major environmental problems over the world. Mercury contamination is a serious threat to human health. Among the existing technologies available for mercury pollution control, the adsorption process can get excellent separation effects and has been further studied. This review is attempted to cover a wide range of adsorbents that were developed for the removal of mercury from the year 2011. Various adsorbents, including the latest adsorbents, are presented along with highlighting and discussing the key advancements on their preparation, modification technologies, and strategies. By comparing their adsorption capacities, it is evident from the literature survey that some adsorbents have shown excellent potential for the removal of mercury. However, there is still a need to develop novel, efficient adsorbents with low cost, high stability, and easy production and manufacture for practical utility.

  4. Severe Illness from Methyl Bromide Exposure at a Condominium Resort--U.S. Virgin Islands, March 2015.

    Science.gov (United States)

    Kulkarni, Prathit A; Duncan, Mary Anne; Watters, Michelle T; Graziano, Leah T; Vaouli, Elena; Cseh, Larry F; Risher, John F; Orr, Maureen F; Hunte-Ceasar, Tai C; Ellis, Esther M

    2015-07-24

    On March 22, 2015, the Agency for Toxic Substances and Disease Registry (ATSDR) was notified by the U.S. Environmental Protection Agency (EPA) of four cases of suspected acute methyl bromide toxicity among family members vacationing at a condominium resort in the U.S. Virgin Islands. Methyl bromide is a pesticide that has been banned in the United States for use in homes and other residential settings. An investigation conducted by the U.S. Virgin Islands Department of Health (VIDOH), the U.S. Virgin Islands Department of Planning and Natural Resources (DPNR), and EPA confirmed that methyl bromide had been used as a fumigant on March 18 in the building where the family had been residing, 2 days before they were transported to the hospital; three family members had life-threatening illness. On March 25, 2015, a stop-use order for methyl bromide was issued by DPNR to the pest control company that had performed the fumigation. Subsequent investigation revealed that previous fumigation with methyl bromide had occurred on October 20, 2014, at the same condominium resort. In addition to the four ill family members, 37 persons who might have been exposed to methyl bromide as a result of the October 2014 or March 2015 fumigations were identified by VIDOH and ATSDR. Standardized health questionnaires were administered to 16 of the 20 persons for whom contact information was available; six of 16 had symptoms consistent with methyl bromide exposure, including headache and fatigue. Pest control companies should be aware that use of methyl bromide is banned in homes and other residential settings, and clinicians should be aware of the toxicologic syndrome that exposure to methyl bromide can cause.

  5. 21 CFR 862.3600 - Mercury test system.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Mercury test system. 862.3600 Section 862.3600....3600 Mercury test system. (a) Identification. A mercury test system is a device intended to measure mercury, a heavy metal, in human specimens. Measurements obtained by this device are used in the diagnosis...

  6. 21 CFR 880.2920 - Clinical mercury thermometer.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Clinical mercury thermometer. 880.2920 Section 880... Devices § 880.2920 Clinical mercury thermometer. (a) Identification. A clinical mercury thermometer is a... mercury. (b) Classification. Class II (special controls). The device is exempt from the premarket...

  7. Mercury flow experiments. 4th report: Measurements of erosion rate caused by mercury flow

    International Nuclear Information System (INIS)

    Kinoshita, Hidetaka; Kaminaga, Masanori; Haga, Katsuhiro; Hino, Ryutaro

    2002-06-01

    The Japan Atomic Energy Research Institute (JAERI) and the High Energy Accelerator Research Organization (KEK) are promoting a construction plan of the Material-Life Science Facility, which is consisted of a Muon Science Facility and a Neutron Scattering Facility, in order to open up the new science fields. The Neutron Scattering Facility will be utilized for advanced fields of Material and Life science using high intensity neutron generated by the spallation reaction of a 1 MW pulsed proton beam and mercury target. Design of the spallation mercury target system aims to obtain high neutron performance with high reliability and safety. Since the target system is using mercury as the target material and contains large amount of radioactive spallation products, it is necessary to estimate reliability for strength of instruments in a mercury flow system during lifetime of the facility. Piping and components in the mercury flow system would be damaged by erosion with mercury flow, since these components will be weak by thickness decreasing. This report presents experimental results of wall thickness change by erosion using a mercury experimental loop. In the experiments, an erosion test section and coupons were installed in the mercury experimental loop, and their wall thickness was measured with an ultra sonic thickness gage after every 1000 hours. As a result, under 0.7 m/s of mercury velocity condition which is slightly higher than the practical velocity in mercury pipelines, the erosion is about 3 μm in 1000 hours. The wall thickness decrease during facility lifetime of 30 years is estimated to be less than 0.5 mm. According to the experimental result, it is confirmed that the effect of erosion on component strength is extremely small. Moreover, a measurement of residual mercury on the piping surface was carried out. As a result, 19 g/m 2 was obtained as the residual mercury for the piping surface. According to this result, estimated amount of residual mercury for

  8. Biomolecular Aspects of Mercury Transformations

    Science.gov (United States)

    Johs, A.; Shi, L.; Miller, S. M.; Summers, A. O.; Liang, L.

    2008-12-01

    Bacteria participate significantly in mercury transformation in natural and industrial environments. Previous studies have shown that bacterial mercury resistance is mediated by the mer operon, typically located on transposons or plasmids. It encodes specific genes that facilitate uptake of mercury species, cleavage of organomercurials, and reduction of Hg(II) to Hg(0). Expression of mer operon genes is regulated by MerR, a metal-responsive regulator protein on the level of transcription. In vitro studies have shown that MerR forms a non-transcribing pre-initiation complex with RNA polymerase and the promoter DNA. Binding of Hg(II) induces conformational changes in MerR and other components of the complex resulting in the transcription of mer operon genes. As part of ongoing investigations on allosteric conformational changes induced by Hg(II) in dimeric MerR, and the implications on the binding of RNA polymerase to the promoter of the mer operon, we applied small angle scattering to study the regulatory mechanism of MerR in the presence and absence of Hg(II). Our results show that in the presence of Hg(II) the MerR dimer undergoes a significant reorientation from a compact state to a conformation revealing two distinct domains. Bacterial reduction of Hg(II) can also occur at concentrations too low to induce mer operon functions. Dissimilatory metal reducing bacteria, such as Shewanella and Geobacter are able to reduce Hg(II) in the presence of mineral oxides. This process has been linked to the activity of outer membrane multiheme cytochromes. We isolated and purified a decaheme outer membrane cytochrome OmcA from Shewanella oneidensis MR-1 and characterized its envelope shape in solution by small angle x-ray scattering. Structural features were identified and compared to homology models. These results show that OmcA is an elongated macromolecule consisting of separate modules, which may be connected by flexible linkers.

  9. Evaluation of the influence of base and alkyl bromide on synthesis of pyrazinoic acid esters through factorial design

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, Joao Paulo dos Santos; Felli, Veni Maria Andres [Universidade de Sao Paulo (USP), SP (Brazil). Faculdade de Ciencias Farmaceuticas. Dept. de Farmacia

    2009-07-01

    Pyrazinoic acid esters have been synthesized as prodrugs of pyrazinoic acid. In the literature, its preparation is reported through the reaction of pyrazinoyl chloride with alcohols and the reaction with DCC/DMAP. In this work, it is reported a 22 factorial design to evaluate the preparation of these esters through the substitution of alkyl bromides with carboxylate anion. The controlled factors were alkyl chain length of bromides (ethyl and hexyl) and the used base (triethylamine and DBU). Results revealed that the used base used has significant effect on yield, and alkyl bromide used has neither significant influence, nor its interaction effect with base. (author)

  10. Evaluation of the influence of base and alkyl bromide on synthesis of pyrazinoic acid esters through factorial design

    International Nuclear Information System (INIS)

    Fernandes, Joao Paulo dos Santos; Felli, Veni Maria Andres

    2009-01-01

    Pyrazinoic acid esters have been synthesized as prodrugs of pyrazinoic acid. In the literature, its preparation is reported through the reaction of pyrazinoyl chloride with alcohols and the reaction with DCC/DMAP. In this work, it is reported a 22 factorial design to evaluate the preparation of these esters through the substitution of alkyl bromides with carboxylate anion. The controlled factors were alkyl chain length of bromides (ethyl and hexyl) and the used base (triethylamine and DBU). Results revealed that the used base used has significant effect on yield, and alkyl bromide used has neither significant influence, nor its interaction effect with base. (author)

  11. Comparative microvascular exchange kinetics of [{sup 77}Br]bromide and {sup 99m}Tc-DTPA in humans

    Energy Technology Data Exchange (ETDEWEB)

    Cousins, Claire [Department of Clinical Radiology, Addenbrooke' s Hospital, Cambridge (United Kingdom); Skehan, Stephen J.; Rolph, Susan M.; Flaxman, Mary E.; Ballinger, James R.; Bird, Nicholas J.; Barber, Robert W.; Peters, Michael A. [Department of Nuclear Medicine, Addenbrooke' s Hospital, Cambridge (United Kingdom)

    2002-05-01

    The plasma clearance curves of small hydrophilic solutes comprise three exponentials, consistent with a three-compartmental distribution model. A previous comparison between inulin and diethylene triamine penta-acetic acid (DTPA) suggested that these three compartments are in series, the first being plasma and the second and third representing compartments within the extravascular space. Moreover, whilst the total distribution volumes of these two indicators were similar, the volume of the second compartment was higher for DTPA. The purpose of the current study was to investigate whether a solute smaller than DTPA, namely bromide, fits the hypothesis that the second space volume is an inverse function of the size of the solute. Two groups of subjects were studied: group A comprised eight patients undergoing routine diagnostic arteriography and group B, eight patients referred for routine measurement of glomerular filtration rate plus two normal volunteers. {sup 99m}Tc-DTPA and sodium [{sup 77}Br]bromide were intravenously administered simultaneously. In group A, frequent arterial samples were obtained up to 40 min after injection, and antecubital venous samples 30 s after each arterial sample. In group B, frequent venous samples were obtained up to 280 min after injection. Volume measurements based on bromide were corrected for erythrocyte bromide accumulation. In both subject groups, the normalised venous concentration ratio of bromide to DTPA, corrected for red cell bromide uptake, was significantly less than unity in the earliest blood samples, being 0.56 (SD 0.08) at 1 min, consistent with faster diffusion of bromide from plasma to interstitial fluid. Furthermore, the extraction fraction of bromide from plasma to interstitial fluid in the forearm was about 0.6, higher than that of DTPA (about 0.5) in spite of red cell bromide accumulation which equilibrated with plasma bromide within 20 s and resulted in a red cell to plasma concentration ratio of 0.51 (0

  12. Mercury in food items from the Idrija Mercury Mine area.

    Science.gov (United States)

    Miklavčič, Ana; Mazej, Darja; Jaćimović, Radojko; Dizdarevi, Tatjana; Horvat, Milena

    2013-08-01

    As a consequence of over 500 years of mining and smelting activities (1490-1995), and of its natural geological occurrence, the soil in the Idrija region is highly contaminated with Hg. In order to assess the present situation regarding the Hg levels in local food samples, concentrations of total mercury (THg) and monomethyl mercury (MeHg) were determined in selected vegetables, mushrooms and fish from the Idrija Hg mine area. Hg levels in the foodstuffs analysed were not very high but were elevated compared to the levels in food from non-contaminated areas. The study showed that THg accumulates in mushrooms (X=5680ng/g dry weight, Min=346ng/g dry weight, Max=17,100 dry weight) and chicory (X=1950ng/g dry weight, Min=86ng/g dry weight, Max=17,100ng/g dry weight). In addition, Se and Cd concentrations were determined by ICP-MS in those vegetable and mushroom species in which the highest Hg levels were found. The levels of Cd and Se were below the threshold levels. Based on data from previous studies, we can conclude that the levels of Hg in food have not diminished significantly during the past 15 years after closure of the Hg mine. Special attention should be given to vegetables such as chicory, representing a local seasonal vegetable eaten frequently. Copyright © 2013 Elsevier Inc. All rights reserved.

  13. Estimating mercury emissions from a zinc smelter in relation to China's mercury control policies

    International Nuclear Information System (INIS)

    Wang, S.X.; Song, J.X.; Li, G.H.; Wu, Y.; Zhang, L.; Wan, Q.; Streets, D.G.; Chin, Conrad K.; Hao, J.M.

    2010-01-01

    Mercury concentrations of flue gas at inlet/outlet of the flue gas cleaning, electrostatic demister, reclaiming tower, acid plant, and mercury contents in zinc concentrate and by-products were measured in a hydrometallurgical zinc smelter. The removal efficiency of flue gas cleaning, electrostatic demister, mercury reclaiming and acid plant was about 17.4%, 30.3%, 87.9% and 97.4% respectively. Flue gas cleaning and electrostatic demister captured 11.7% and 25.3% of the mercury in the zinc concentrate, respectively. The mercury reclaiming tower captured 58.3% of the mercury in the zinc concentrate. About 4.2% of the mercury in the zinc concentrate was captured by the acid plant. Consequently, only 0.8% of the mercury in the zinc concentrate was emitted to the atmosphere. The atmospheric mercury emission factor was 0.5 g t -1 of zinc produced for the tested smelter, indicating that this process offers the potential to effectively reduce mercury emissions from zinc smelting. - Modern scale production equipped with acid plant and Hg reclaiming tower will significantly reduce Hg emissions from zinc smelters in China.

  14. Treatment of mercury containing waste

    Science.gov (United States)

    Kalb, Paul D.; Melamed, Dan; Patel, Bhavesh R; Fuhrmann, Mark

    2002-01-01

    A process is provided for the treatment of mercury containing waste in a single reaction vessel which includes a) stabilizing the waste with sulfur polymer cement under an inert atmosphere to form a resulting mixture and b) encapsulating the resulting mixture by heating the mixture to form a molten product and casting the molten product as a monolithic final waste form. Additional sulfur polymer cement can be added in the encapsulation step if needed, and a stabilizing additive can be added in the process to improve the leaching properties of the waste form.

  15. Geodesy at Mercury with MESSENGER

    Science.gov (United States)

    Smith, David E.; Zuber, Maria t.; Peale, Stanley J.; Phillips, Roger J.; Solomon, Sean C.

    2006-01-01

    In 2011 the MESSENGER (MErcury Surface, Space ENvironment, GEochemistry, and Ranging) spacecraft will enter Mercury orbit and begin the mapping phase of the mission. As part of its science objectives the MESSENGER mission will determine the shape and gravity field of Mercury. These observations will enable the topography and the crustal thickness to be derived for the planet and will determine the small libration of the planet about its axis, the latter critical to constraining the state of the core. These measurements require very precise positioning of the MESSENGER spacecraft in its eccentric orbit, which has a periapsis altitude as low as 200 km, an apoapsis altitude near 15,000 km, and a closest approach to the surface varying from latitude 60 to about 70 N. The X-band tracking of MESSENGER and the laser altimetry are the primary data that will be used to measure the planetary shape and gravity field. The laser altimeter, which has an expected range of 1000 to 1200 km, is expected to provide significant data only over the northern hemisphere because of MESSENGER's eccentric orbit. For the southern hemisphere, radio occultation measurements obtained as the spacecraft passes behind the planet as seen from Earth and images obtained with the imaging system will be used to provide the long-wavelength shape of the planet. Gravity, derived from the tracking data, will also have greater resolution in the northern hemisphere, but full global models for both topography and gravity will be obtained at low harmonic order and degree. The limiting factor for both gravity and topography is expected to be knowledge of the spacecraft location. Present estimations are that in a combined tracking, altimetry, and occultation solution the spacecraft position uncertainty is likely to be of order 10 m. This accuracy should be adequate for establishing an initial geodetic coordinate system for Mercury that will enable positioning of imaged features on the surface, determination of

  16. Mercury migration into ground water, a literature study

    Energy Technology Data Exchange (ETDEWEB)

    Carlton, W.H.; Carden, J.L.; Kury, R.; Eichholz, G.G.

    1994-11-01

    This report presents a broad review of the technical literature dealing with mercury migration in the soil. The approach followed was to identify relevant articles by searching bibliographic data bases, obtaining the promising articles and searching these articles for any additional relevant citations. Eight catagories were used to organize the literature, with a review and summary of each paper. Catagories used were the following: chemical states of mercury under environmental conditions; diffusion of mercury vapor through soil; solubility and stability of mercury in environmental waters; transport of mercury on colloids; models for mercury migration through the environment; analytical techniques; retention of mercury by soil components; formation of organomecurials.

  17. Study of high levels indoor air mercury contamination from mercury amalgam use in dentistry

    International Nuclear Information System (INIS)

    Khwaja, M.A.; Abbasi, M.S.; Mehmood, F.; Jahangir, S.

    2014-01-01

    In 2005, United Nations Environment Programme (UNEP) estimated that 362 tonnes of dental mercury are consumed annually worldwide. Dental mercury amalgams also called silver fillings and amalgam fillings are widely done. These fillings gave off mercury vapours. Estimated average absorbed concentrations of mercury vapours from dental fillings vary from 3,000 to 17,000 ng Hg. Mercury (Hg) also known as quick silver is an essential constituent of dental amalgam. It is a toxic substance of global concern. A persistent pollutant, mercury is not limited to its source but it travels, on time thousands of kilometers away from the source. Scientific evidence, including, UNEP Global Mercury report, establishes mercury as an extremely toxic substance, which is a major threat to wildlife, ecosystem and human health, at a global scale. Children are more at risk from mercury poisoning which affects their neurological development and brain. Mercury poisoning diminishes memory, attention, thinking and sight. In the past, a number of studies at dental sites in many countries have been carried out and reported which have been reviewed and briefly described. This paper describes and discusses the recent investigations, regarding mercury vapours level in air, carried out at 18 dental sites in Pakistan and other countries. It is evident from the data of 42 dental sites in 17 countries, including, selected dental sites in five main cities of Pakistan, described and discussed in this paper that at most dental sites in many countries including Pakistan, the indoor mercury vapours levels exceed far above the permissible limit, recommended for safe physical and mental health. At these sites, public, in general, and the medical, paramedical staff and vulnerable population, in particular, are at most serious risk to health resulting from exposure to toxic and hazardous mercury. (author)

  18. Substance Flow Analysis of Mercury in China

    Science.gov (United States)

    Hui, L. M.; Wang, S.; Zhang, L.; Wang, F. Y.; Wu, Q. R.

    2015-12-01

    In previous studies, the emission of anthropogenic atmospheric Hg in China as well as single sector have been examined a lot. However, there might have been more Hg released as solid wastes rather than air. Hg stored in solid wastes may be released to air again when the solid wastes experience high temperature process or cause local pollution if the solid wastes are stacked casually for a long time. To trace the fate of Hg in China, this study developed the substance flow of Hg in 2010 covering all the sectors summarized in table 1. Below showed in Figure 1, the total Hg input is 2825t. The unintentional input of Hg, mined Hg, and recycled Hg account for 57%, 32% and 11% respectively. Figure 2 provides the detail information of substance flow of Hg. Byproducts from one sector may be used as raw materials of another, causing cross Hg flow between sectors. The Hg input of cement production is 303 t, of which 34% comes from coal and limestone, 33% comes from non-ferrous smelting, 23% comes from coal combustion, 7% comes from iron and steel production and 3% comes from mercury mining. Hg flowing to recycledHg production is 639 t, mainly from Hg contained in waste active carbon and mercuric chloride catalyst from VCM production and acid sludge from non-ferrous smelting. There are 20 t mercury flowing from spent mercury adding products to incineration. Figure1 and Figure 2 also show that 46% of the output Hg belongs to "Lagged release", which means this part of mercury might be released later. The "Lagged release" Hg includes 809 t Hg contained in stacked byproducts form coal combustion, non-ferrous smelting, iron and steel production, Al production, cement production and mercury mining, 161t Hg stored in the pipeline of VCM producing, 10 t Hg in fluorescent lamps that are in use and 314 t mercury stored in materials waiting to be handled with in recycled mercury plants. There is 112 t Hg stored in landfill and 129 t Hg exported abroad with the export of mercury adding

  19. Mercury in the environment : a primer

    Energy Technology Data Exchange (ETDEWEB)

    Lourie, B.; Glenn, W. (ed.); Ogilvie, K.; Everhardus, E.; Friesen, K.; Rae, S.

    2003-06-01

    This report provides an overview of the occurrence and effects of mercury in the environment and its impacts on human health. Low levels of mercury occur naturally everywhere in the environment in plants, animals, rocks and air. Incidental emissions occur when natural mercury is released to the environment through human activity. In Canada, coal burning and metal processing are the two largest point sources of atmospheric mercury emissions. Energy facilities have the option to invest in expensive control technologies for coal plants, or they can generate electricity from alternative energy sources. Energy conservation, however, offers the greatest overall benefits for the environment and the public. Mercury can also be released when products containing mercury (such as electrical switches, thermostats, dental amalgam, and thermometers) are broken while in use, or when they are crushed in garbage trucks and dumped in landfills. Source separation is the best way to reduce waste-related emissions. Once mercury is released to the natural environment, it can be transported long distances through air or watercourses. It is volatile, therefore evaporates readily to the atmosphere where it may do one of three things: it may fall out near the point where it was emitted; it may be transported long distances to some point downwind; or, it may enter the global atmospheric mercury pool where it will circle the globe for a year or more within the Earth's major weather systems before being deposited. Data from Canada's National Pollutant Release Inventory indicates that mercury releases and transfers total 28,674 kg per year. The most critical component of the mercury cycle is the conversion of inorganic forms of mercury to the organic compound methylmercury which is more toxic to humans. Most concern about mercury focuses on lakes and other aquatic ecosystems. Fish in hydroelectric reservoirs have been found to contain elevated methylmercury levels because natural

  20. 40 CFR Appendix Xiii to Part 266 - Mercury Bearing Wastes That May Be Processed in Exempt Mercury Recovery Units

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Mercury Bearing Wastes That May Be Processed in Exempt Mercury Recovery Units XIII Appendix XIII to Part 266 Protection of Environment... XIII to Part 266—Mercury Bearing Wastes That May Be Processed in Exempt Mercury Recovery Units These...

  1. Groundwater Modeling of Mercury Pollution at a Former Mercury Cell Chlor Alkali Facility in Pavlodar City, Kazakhstan

    Science.gov (United States)

    In northern Kazakhstan, there is a serious case of mercury pollution near the city of Pavlodar from an old mercury cell chlor-alkali plant. The soil, sediment, and water is severely contaminated with mercury and mercury compounds as a result of the industrial activity of this ch...

  2. Particulate and fog- and cloud-water bromide in polluted air

    Science.gov (United States)

    Lammel, Gerhard

    Particulate water soluble bromide was determined in source regions at concentrations typically 0.1-1 hg m -3, and—distinctly less concentrated—at subalpine mountain sites downwind from urban areas. High to extremely high concentrations, 1-10 mg L-1 and above, were found in urban fog water and lower values, 0.01-0.1 mg L-1 in orographic clouds at the mountain sites. Bromide was predominantly concentrated in the accumulation mode of the atmospheric aerosol. In fog- and cloud water a tendency to higher concentrations in small droplets was observed. The particulate Br concentration level observed at the urban sites and a rural site is comparable to what had been measured 5-10 yr earlier at urban sites in Germany although the former major anthropogenic Br source, 1,2-dibromoethane in gasoline, had been reduced and finally phased out.

  3. A novel model-based approach for dose determination of glycopyrronium bromide in COPD

    Directory of Open Access Journals (Sweden)

    Arievich Helen

    2012-12-01

    Full Text Available Abstract Background Glycopyrronium bromide (NVA237 is an inhaled long-acting muscarinic antagonist in development for treatment of COPD. This study compared the efficacy and safety of once-daily (OD and twice-daily (BID glycopyrronium bromide regimens, using a novel model-based approach, in patients with moderate-to-severe COPD. Methods Double-blind, randomized, dose-finding trial with an eight-treatment, two-period, balanced incomplete block design. Patients (smoking history ≥10 pack-years, post-bronchodilator FEV1 ≥30% and 1/FVC 1 at Day 28. Results 385 patients (mean age 61.2 years; mean post-bronchodilator FEV1 53% predicted were randomized; 88.6% completed. All OD and BID dosing regimens produced dose-dependent bronchodilation; at Day 28, increases in mean trough FEV1 versus placebo were statistically significant for all regimens, ranging from 51 mL (glycopyrronium bromide 12.5 μg OD to 160 mL (glycopyrronium bromide 50 μg BID. Pharmacodynamic steady-state was reached by Day 7. There was a small separation (≤37 mL between BID and OD dose–response curves for mean trough FEV1 at steady-state in favour of BID dosing. Over 24 hours, separation between OD and BID regimens was even smaller (FEV1 AUC0-24h maximum difference for equivalent daily dose regimens: 8 mL. Dose–response results for FEV1 at 12 hours, FEV1 AUC0-12h and FEV1 AUC0-4h at steady-state showed OD regimens provided greater improvement over placebo than BID regimens for total daily doses of 25 μg, 50 μg and 100 μg, while the reverse was true for OD versus BID regimens from 12–24 hours. The 12.5 μg BID dose produced a marginally higher improvement in trough FEV1 versus placebo than 50 μg OD, however, the response at 12 hours over placebo was suboptimal (74 mL. Glycopyrronium bromide was safe and well tolerated at all doses. Conclusions Glycopyrronium bromide 50 μg OD provides significant bronchodilation over a 24 hour period

  4. Temporary arrest of fetal movement with pancuronium bromide to enable antenatal magnetic resonance imaging of holoprosencephaly.

    Science.gov (United States)

    Horvath, L; Seeds, J W

    1989-10-01

    The well-known ability of real-time ultrasound to detect congenital abnormalities is often limited by acoustic artifact or fetal position or both. Magnetic resonance imaging can provide superior soft tissue resolution but is vulnerable to maternal and fetal motion artifact. Described and illustrated here is a case of fetal holoprosencephaly that was not of diagnostic clarity on ultrasound. The fetus was paralyzed with an intramuscular injection of pancuronium bromide before a resonance imaging study. Successful fetal paralysis with pancuronium bromide has been reported prior to a variety of fetal interventions for the temporary arrest of fetal movement. The resonance study illustrated here was of significantly superior clarity and improved the accuracy of prognosis and management counseling. It is concluded that in selected cases where ultrasound is not of diagnostic clarity due to acoustic artifact, fetal paralysis and magnetic resonance imaging may be considered.

  5. Preparation and optical characteristics of layered perovskite-type lead-bromide-incorporated azobenzene chromophores

    Science.gov (United States)

    Sasai, Ryo; Shinomura, Hisashi

    2013-02-01

    Lead bromide-based layered perovskite powders with azobenzene derivatives were prepared by a homogeneous precipitation method. From the diffuse reflectance (DR) and photoluminescence (PL) spectra of the hybrid powder materials, the present hybrids exhibited sharp absorption and PL peaks originating from excitons produced in the PbBr42- layer. When the present hybrid powder was irradiated with UV light at 350 nm, the absorption band from the trans-azobenzene chromophore, observed around 350 nm, decreased, while the absorption band from the cis-azobenzene chromophore, observed around 450 nm, increased. These results indicate that azobenzene chromophores in the present hybrid materials exhibit reversible photoisomerization. Moreover, it was found that the PL intensity from the exciton also varied due to photoisomerization of the azobenzene chromophores in the present hybrid. Thus, for the first time we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation.

  6. Thermodynamic Properties of Hydrogen + Tetra-n-Butyl Ammonium Bromide Semi-Clathrate Hydrate

    Directory of Open Access Journals (Sweden)

    Shunsuke Hashimoto

    2010-01-01

    Full Text Available Thermodynamic stability and hydrogen occupancy on the hydrogen + tetra-n-butyl ammonium bromide semi-clathrate hydrate were investigated by means of Raman spectroscopic and phase equilibrium measurements under the three-phase equilibrium condition. The structure of mixed gas hydrates changes from tetragonal to another structure around 95 MPa and 292 K depending on surrounding hydrogen fugacity. The occupied amount of hydrogen in the semi-clathrate hydrate increases significantly associated with the structural transition. Tetra-n-butyl ammonium bromide semi-clathrate hydrates can absorb hydrogen molecules by a pressure-swing without destroying the hydrogen bonds of hydrate cages at 15 MPa or over.

  7. Mechanism of HERG potassium channel inhibition by tetra-n-octylammonium bromide and benzethonium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Long, Yan; Lin, Zuoxian [Key Laboratory of Regenerative Biology, Guangzhou Institute of Biomedicine and Health, Chinese Academy of Sciences, Guangzhou 510530 (China); Xia, Menghang; Zheng, Wei [National Center for Advancing Translational Sciences, National Institutes of Health, Bethesda, MD 20892 (United States); Li, Zhiyuan, E-mail: li_zhiyuan@gibh.ac.cn [Key Laboratory of Regenerative Biology, Guangzhou Institute of Biomedicine and Health, Chinese Academy of Sciences, Guangzhou 510530 (China)

    2013-03-01

    Tetra-n-octylammonium bromide and benzethonium chloride are synthetic quaternary ammonium salts that are widely used in hospitals and industries for the disinfection and surface treatment and as the preservative agent. Recently, the activities of HERG channel inhibition by these compounds have been found to have potential risks to induce the long QT syndrome and cardiac arrhythmia, although the mechanism of action is still elusive. This study was conducted to investigate the mechanism of HERG channel inhibition by these compounds by using whole-cell patch clamp experiments in a CHO cell line stably expressing HERG channels. Tetra-n-octylammonium bromide and benzethonium chloride exhibited concentration-dependent inhibitions of HERG channel currents with IC{sub 50} values of 4 nM and 17 nM, respectively, which were also voltage-dependent and use-dependent. Both compounds shifted the channel activation I–V curves in a hyperpolarized direction for 10–15 mV and accelerated channel activation and inactivation processes by 2-fold. In addition, tetra-n-octylammonium bromide shifted the inactivation I–V curve in a hyperpolarized direction for 24.4 mV and slowed the rate of channel deactivation by 2-fold, whereas benzethonium chloride did not. The results indicate that tetra-n-octylammonium bromide and benzethonium chloride are open-channel blockers that inhibit HERG channels in the voltage-dependent, use-dependent and state-dependent manners. - Highlights: ► Tetra-n-octylammonium and benzethonium are potent HERG channel inhibitors. ► Channel activation and inactivation processes are accelerated by the two compounds. ► Both compounds are the open-channel blockers to HERG channels. ► HERG channel inhibition by both compounds is use-, voltage- and state dependent. ► The in vivo risk of QT prolongation needs to be studied for the two compounds.

  8. Synthesis of Dimethyl Aryl Acylsulfonium Bromides from Aryl Methyl Ketones in a DMSO-HBr System

    Directory of Open Access Journals (Sweden)

    Zhiling Cao

    2013-12-01

    Full Text Available A new, simplified method for the synthesis of dimethyl aryl acylsulfonium salts has been developed. A series of dimethyl aryl acylsulfonium bromides were prepared by the reaction of aryl methyl ketones with hydrobromic acid and dimethylsulfoxide (DMSO. This sulfonium salt confirms that bromine production and the bromination reaction take place in the DMSO-HBr oxidation system. What’s more, it is also a key intermediate for the synthesis of arylglyoxals.

  9. Synthesis of dimethyl aryl acylsulfonium bromides from aryl methyl ketones in a DMSO-HBr system.

    Science.gov (United States)

    Cao, Zhiling; Shi, Dahua; Qu, Yingying; Tao, Chuanzhou; Liu, Weiwei; Yao, Guowei

    2013-12-16

    A new, simplified method for the synthesis of dimethyl aryl acylsulfonium salts has been developed. A series of dimethyl aryl acylsulfonium bromides were prepared by the reaction of aryl methyl ketones with hydrobromic acid and dimethylsulfoxide (DMSO). This sulfonium salt confirms that bromine production and the bromination reaction take place in the DMSO-HBr oxidation system. What's more, it is also a key intermediate for the synthesis of arylglyoxals.

  10. Bromide (Br) - Based Synthesis of Ag Nanocubes with High-Yield

    OpenAIRE

    Wu, Fan; Wang, Wenhui; Xu, Zhongfeng; Li, Fuli

    2015-01-01

    The geometry of metal nanoparticles greatly affects the properties of the localized surface plasmon resonance and surface-enhanced Raman scattering. The synthesis of metal nanoparticles with controllable geometry has thus attracted extensive attentions. In this work, we report a modified polyol synthesis approach of silver (Ag) nanocubes through tuning the concentration of bromide ions (Br? ions). We have systematically investigated the effect of Br? ions in the polyol process, and find that ...

  11. Laboratory Evaluation of Drop-in Solvent Alternatives to n-Propyl Bromide for Vapor Degreasing

    Science.gov (United States)

    Mitchell, Mark A.; Lowrey, Nikki M.

    2012-01-01

    Based on this limited laboratory study, solvent blends of trans-1,2 dichloroethylene with HFEs, HFCs, or PFCs appear to be viable alternatives to n-propyl bromide for vapor degreasing. The lower boiling points of these blends may lead to greater solvent loss during use. Additional factors must be considered when selecting a solvent substitute, including stability over time, VOC, GWP, toxicity, and business considerations.

  12. Adsorption of Indigo Carmine Dye Using Cetyltrimethylammonium Bromide (CTAB) Surfactant Modified Zeolite

    OpenAIRE

    Fauziyah, Nurul; Sriatun, Sriatun; Pardoyo, Pardoyo

    2015-01-01

    Research of indigo carmine dye adsorption using natural zeolite modified by cetyltrimethylammonium bromide (CTAB) surfactant has been done. The purpose of this study was to modify the natural zeolite using CTAB surfactant and to determine its ability on the adsorption of indigo carmine dye. The stages of the study included the activation of zeolites, modifying zeolites using CTAB surfactant and adsorption test of indigo carmine dye. The results showed that the zeolites could be modified by CT...

  13. Dental amalgam and urinary mercury concentrations: a descriptive study

    OpenAIRE

    Nicolae, Alexandra; Ames, Harry; Qui?onez, Carlos

    2013-01-01

    Background Dental amalgam is a source of elemental and inorganic mercury. The safety of dental amalgam in individuals remains a controversial issue. Urinary mercury concentrations are used to assess chronic exposure to elemental mercury. At present, there are no indications of mercury-associated adverse effects at levels below 5??g Hg/g creatinine (Cr) or 7??g Hg/L (urine). The purpose of the present study is to determine the overall urinary mercury level in the Canadian general population in...

  14. Serum triglyceride concentration in dogs with epilepsy treated with phenobarbital or with phenobarbital and bromide.

    Science.gov (United States)

    Kluger, Elissa K; Malik, Richard; Ilkin, William J; Snow, David; Sullivan, David R; Govendir, Merran

    2008-10-15

    To compare serum triglyceride concentrations obtained after food had been withheld (i.e., fasting concentrations) in dogs with epilepsy that had been treated long term (> or = 3 months) with phenobarbital or with phenobarbital and potassium bromide with concentrations in healthy control dogs. Cross-sectional study. 57 epileptic dogs that had been treated with phenobarbital (n=28) or with phenobarbital and bromide (29) and 57 healthy, untreated control dogs matched on the basis of age, breed, sex, neuter status, and body condition score. Blood samples were collected after food had been withheld for at least 12 hours, and serum biochemical and lipid concentrations were determined. Oral fat tolerance tests were performed in 15 control dogs and 9 dogs with epilepsy treated with phenobarbital alone. 19 of the 57 (33%) epileptic dogs had fasting serum triglyceride concentrations greater than the upper reference limit. Nine (16%) dogs had a history of pancreatitis, and 5 of the 9 had high fasting serum triglyceride concentrations at the time of the study. A significant relationship was found between body condition score and fasting serum triglyceride concentration in all dogs, but serum triglyceride concentration was not significantly associated with phenobarbital dosage or serum phenobarbital concentration. Results suggested that dogs treated long term with phenobarbital or with phenobarbital and bromide may develop hypertriglyceridemia. Fasting serum triglyceride concentration should be periodically monitored in dogs treated with phenobarbital because hypertriglyceridemia is a risk factor for pancreatitis.

  15. Pitting Corrosion Behavior of 304 SS and 316 SS Alloys in Aqueous Chloride and Bromide Solutions

    Directory of Open Access Journals (Sweden)

    Ibtehal Kareem Shakir

    2018-01-01

    Full Text Available The importance of the present work falls on the pitting corrosion behavior investigation of 304 SS and 316 SS alloys in 3.5 wt% of aqueous solution bearing with chloride and bromide anion at different solutions temperature range starting from (20-50oC due to the pitting corrosion tremendous effect on the economic, safety and materials loss due to leakage. The impact of solution temperatures on the pitting corrosion resistance at 3.5wt% (NaCl and NaBr solutions for the 304 SS and 316 SS has been investigated utilizing the cyclic polarization techniques at the potential range -400 to1000 mV vs. SCE at 40 mV/sec scan rate followed by the surface characterization employing Scanning Electron Microscope. The results show that a significant decline in the pitting corrosion potential Ep values of both stainless steel alloys in chloride and bromide solution during temperature increase attributed to the pitting corrosion potential decreased arises from the modification of the passive film properties. The surface examination using optical microscope and scanning electron microscope prove the occurring of higher pitting density over 304 SS in chloride solution than that observed in bromide solution with a non-circular lacy cover pitfall out at the center and falls inside the pits hall in comparison to the isolated circular lacy cover pit formed on 316 SS in 3.5wt% NaBr solution at 50 oC.

  16. Preparation and optical characteristics of layered perovskite-type lead-bromide-incorporated azobenzene chromophores

    Energy Technology Data Exchange (ETDEWEB)

    Sasai, Ryo, E-mail: rsasai@riko.shimane-u.ac.jp [Department of Applied Chemistry, Graduate School of Engineering, Nagoya University, F3-3(250), Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Shinomura, Hisashi [Department of Applied Chemistry, Graduate School of Engineering, Nagoya University, F3-3(250), Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan)

    2013-02-15

    Lead bromide-based layered perovskite powders with azobenzene derivatives were prepared by a homogeneous precipitation method. From the diffuse reflectance (DR) and photoluminescence (PL) spectra of the hybrid powder materials, the present hybrids exhibited sharp absorption and PL peaks originating from excitons produced in the PbBr{sub 4}{sup 2-} layer. When the present hybrid powder was irradiated with UV light at 350 nm, the absorption band from the trans-azobenzene chromophore, observed around 350 nm, decreased, while the absorption band from the cis-azobenzene chromophore, observed around 450 nm, increased. These results indicate that azobenzene chromophores in the present hybrid materials exhibit reversible photoisomerization. Moreover, it was found that the PL intensity from the exciton also varied due to photoisomerization of the azobenzene chromophores in the present hybrid. Thus, for the first time we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation. - Graphical abstract: For the first time, we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation. Highlights: Black-Right-Pointing-Pointer PbBr-based layered perovskite with azobenezene derivatives could be synthesized by a homogeneous precipitation method. Black-Right-Pointing-Pointer Azobenzene derivatives incorporated the present hybrid that exhibited reversible photoisomerization under UV and/or visible light irradiation. Black-Right-Pointing-Pointer PL property of the present hybrid could also be varied by photoisomerization.

  17. Thorium (4) fluoride complexes in molten iodides and bromides of alkali metals

    International Nuclear Information System (INIS)

    Smirnov, M.V.; Kudyakov, V.Ya.; Shishkin, V.Yu.

    1977-01-01

    The composition and conventional stability constant of fluoride complex formed by tetravalent thorium have been calculated on the basis of measurement of the e.m.f. of galvanic cells, in relation to the temperature and concentration of fluorides in mixed fluoride-bromide and fluoride-iodide melts. It has been established that at elevated temperatures Th(IV) forms anion complexes whose average number of ligands m is not a whole number, varies with the temperature and concentration of the fluorides, and ranges from 6.5 to 5.9. The conventional stability constants of the complexes ThF 6 2- . ThF 7 3- are determined, as well as the variations in the Gibbs energy of reactions of their formation. It is shown that the enthalpies of the reactions of formation of these complexes become more negative with an increase in the difference of the radii of the fluoride anion and the chloride, bromide or iodide anion displaced by it from the corresponding thorium grouping in a pure chloride, bromide or iodide melt

  18. The Effect of Ozonation Process on Bromide-Containing Groundwaters in Bandung Area and Its Surroundings

    Directory of Open Access Journals (Sweden)

    Mindriany Syafila

    2012-11-01

    Full Text Available Disinfection process was applied as the last step of the water treatment to kill pathogenic bacteria in the water. However, according to several studies, the ozonation disinfection process could form undesired by-products. One of the by-products potentially affecting human life is bromate produced from bromide ionic-containing water. This study was carried out to examine the effect of raw water characteristics and pH on bromate formation. Also, the performance of bromate formation for a period of exposure time was analyzed. Raw waters taken from four different areas around Bandung were exposed to ozone introduced to a reactor with a flow rate of 2 L/min. The pH of the raw waters varied from 4, 7 to 10. The results show that there was no evidence of an initial bromide ion concentration, whereas a change in pH value gives a significantly different outcome. In acidic condition (pH of 4 the bromate formation tends to decrease, whereas when the pH value increases to a pH of 10, the bromate formation increases. Therefore, for drinking water with a neutral pH, when bromide ions are detected in the raw water, the drinking water may be toxic due to the presence of bromate.

  19. Electrolytic coloration and spectral properties of hydroxyl-doped potassium bromide single crystals

    International Nuclear Information System (INIS)

    Qi, Lan; Song, Cuiying; Gu, Hongen

    2013-01-01

    Hydroxyl-doped potassium bromide single crystals are colored electrolytically at various temperatures and voltages by using a pointed cathode and a flat anode. The characteristic OH − spectral band is observed in absorption spectrum of uncolored single crystal. The characteristic O − , OH − , U, V 2 , O 2− −V a + , M L1 , F and M spectral bands are observed simultaneously in absorption spectra of colored single crystals. Current–time curve for electrolytic coloration of hydroxyl-doped potassium bromide single crystal and its relationship with electrolytic coloration processes are given. Production and conversion of color centers are explained. - Highlights: ► We expanded the traditional electrolysis method. ► Hydroxyl-doped potassium bromide crystals were colored electrolytically for the first time. ► Useful V, F and F-aggregate color centers were produced in colored crystals. ► V color centers were produced directly and F as well as F-aggregate color centers indirectly.

  20. Preparation and optical characteristics of layered perovskite-type lead-bromide-incorporated azobenzene chromophores

    International Nuclear Information System (INIS)

    Sasai, Ryo; Shinomura, Hisashi

    2013-01-01

    Lead bromide-based layered perovskite powders with azobenzene derivatives were prepared by a homogeneous precipitation method. From the diffuse reflectance (DR) and photoluminescence (PL) spectra of the hybrid powder materials, the present hybrids exhibited sharp absorption and PL peaks originating from excitons produced in the PbBr 4 2− layer. When the present hybrid powder was irradiated with UV light at 350 nm, the absorption band from the trans-azobenzene chromophore, observed around 350 nm, decreased, while the absorption band from the cis-azobenzene chromophore, observed around 450 nm, increased. These results indicate that azobenzene chromophores in the present hybrid materials exhibit reversible photoisomerization. Moreover, it was found that the PL intensity from the exciton also varied due to photoisomerization of the azobenzene chromophores in the present hybrid. Thus, for the first time we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation. - Graphical abstract: For the first time, we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation. Highlights: ► PbBr-based layered perovskite with azobenezene derivatives could be synthesized by a homogeneous precipitation method. ► Azobenzene derivatives incorporated the present hybrid that exhibited reversible photoisomerization under UV and/or visible light irradiation. ► PL property of the present hybrid could also be varied by photoisomerization.

  1. Room temperature synthesis of silver nanowires from tabular silver bromide crystals in the presence of gelatin

    Science.gov (United States)

    Liu, Suwen; Wehmschulte, Rudolf J.; Lian, Guoda; Burba, Christopher M.

    2006-03-01

    Long silver nanowires were synthesized at room temperature by a simple and fast process derived from the development of photographic films. A film consisting of an emulsion of tabular silver bromide grains in gelatin was treated with a photographic developer (4-(methylamino)phenol sulfate (metol), citric acid) in the presence of additional aqueous silver nitrate. The silver nanowires have lengths of more than 50 μm, some even more than 100 μm, and average diameters of about 80 nm. Approximately, 70% of the metallic silver formed in the reduction consists of silver nanowires. Selected area electron diffraction (SAED) results indicate that the silver nanowires grow along the [111] direction. It was found that the presence of gelatin, tabular silver bromide crystals and silver ions in solution are essential for the formation of the silver nanowires. The nanowires appear to originate from the edges of the silver bromide crystals. They were characterized by transmission electron microscopy (TEM), SAED, scanning electron microscopy (SEM), and powder X-ray diffraction (XRD).

  2. Trends in bromide wet deposition concentrations in the contiguous United States, 2001-2016.

    Science.gov (United States)

    Wetherbee, Gregory A; Lehmann, Christopher M B; Kerschner, Brian M; Ludtke, Amy S; Green, Lee A; Rhodes, Mark F

    2018-02-01

    Bromide (Br - ) and other solute concentration data from wet deposition samples collected and analyzed by the National Atmospheric Deposition Program (NADP) from 2001 to 2016, were statistically analyzed for trends both geographically and temporally by precipitation type. Analysis was limited to NADP sites in the contiguous 48 United States. The Br - concentrations for this time period had a high number of values censored at the detection limits with greater than 86 percent of sample concentrations below analytical detection. Bromide was more frequently detected at NADP sites in coastal regions. Analysis using specialized statistical techniques for censored data revealed that Br - concentrations varied by precipitation type with higher concentrations usually observed in liquid versus precipitation containing snow. Negative temporal trends in Br - wet deposition concentrations were observed at a majority of NADP sites; approximately 25 percent of these trend values were statistically significant at less than 0.05 to 0.10 significance levels. Potential causes for the negative trends were explored, including annual and seasonal changes in precipitation depth, reduced emissions of methyl bromide (CH 3 Br) from coastal wetlands, and declining industrial use of bromine compounds. The results indicate that Br - in non-coastal wet-deposition comes mainly from long-range transport, not local sources. Correlations between Br - , chloride, and nitrate concentrations also were evaluated. Published by Elsevier Ltd.

  3. Mercury's magnetosphere and magnetotial revisited

    International Nuclear Information System (INIS)

    Bergan, S.; Engle, I.M.

    1981-01-01

    Magnetic observations which are not complicated by currents of trapped plasma are a good test of geomagnetopause and geomagnetotail predictions. Recent attempts to model the Hermean magnetospheric field based on a planet-centered magnetic multipole field with a quadrupole moment in addition to the planetary dipole field or a dipole field linearly displaced from planet center and no quadrupole moment have produced reasonably good fits to the Mercury magnetic field measurements. In this work we find a better fit for a dipole displacement from the planet center by making use of an improved representation of the magnetic field in the magnetotail, where many of the Mercury measurements were made. The rms deviation of the data was reduced from 10. or 11. γ to 9.3 γ by employing this new tail field representation. Also, by making use of this new tail field representation, we find a best fit for a dipole displacement of -0.0285 R/sub M/ (earlier, 0.026 R/sub M/) toward the dawn in the magnetic equatorial plane and 0.17 R/sub M/ (earlier, 0.189 R/sub M/ (earlier 0.189 R/sub M/) northward along the magnetic dipole axis, where R/sub M/ is the planet radius. Thus with only minor adjustments in the displacement vector of the dipole from the planet center we achieve a measurable improvement in the fit of the data by using the improved magnetotail field representation

  4. A thin, dense crust for Mercury

    Science.gov (United States)

    Sori, Michael M.

    2018-05-01

    Crustal thickness is a crucial geophysical parameter in understanding the geology and geochemistry of terrestrial planets. Recent development of mathematical techniques suggests that previous studies based on assumptions of isostasy overestimated crustal thickness on some of the solid bodies of the solar system, leading to a need to revisit those analyses. Here, I apply these techniques to Mercury. Using MESSENGER-derived elemental abundances, I calculate a map of grain density (average 2974 ± 89 kg/m3) which shows that Pratt isostasy is unlikely to be a major compensation mechanism of Mercury's topography. Assuming Airy isostasy, I find the best fit value for Mercury's mean crustal thickness is 26 ± 11 km, 25% lower than the most recently reported and previously thinnest number. Several geological implications follow from this relatively low value for crustal thickness, including showing that the largest impacts very likely excavated mantle material onto Mercury's surface. The new results also show that Mercury and the Moon have a similar proportion of their rocky silicates composing their crusts, and thus Mercury is not uniquely efficient at crustal production amongst terrestrial bodies. Higher resolution topography and gravity data, especially for the southern hemisphere, will be necessary to refine Mercury's crustal parameters further.

  5. Elimination of mercury from amalgam in rats

    Energy Technology Data Exchange (ETDEWEB)

    Galic, N. [Dept. of Dental Pathology, School of Dentistry, Zagreb (Croatia); Prpic-Mehicic, G.; Prester, Lj.; Blanusa, M. [Inst. for Medical Research and Occupational Health, Zagreb (Croatia); Krnic, Z.; Erceg, D. [Pliva Pharmaceutical Co., Biomedicine Research Inst. ' ' Pliva' ' , Zagreb (Croatia)

    2001-07-01

    The aim of this study was to measure the urinary mercury excretion in rats exposed to amalgam over a two months period. Animals were either exposed to mercury from 4 dental amalgams or fed the diet containing powdered amalgams. The results showed significantly higher mercury amount in urine of both exposed groups than in control. Even two months after the amalgam had been placed in rats teeth, the amount of mercury in the urine remained 4-5 times higher than in control, and 4 times higher than in rats exposed to diet containing powdered amalgam. The elevated urinary Hg amount was accompanied by an increased level of total protein in urine. In the same exposure period the excretion of total protein in urine of rats with amalgam fillings was 2 times higher than in control and 1.5 times higher than in rats exposed to amalgam through diet. Concentrations of mercury in the sera of all groups were below the detection limit of the method. The results show that amount of mercury and protein in the urine of rats were related to the mercury release from dental amalgam. (orig.)

  6. Mercury flow experiments. 4th report Measurements of erosion rate caused by mercury flow

    CERN Document Server

    Kinoshita, H; Hino, R; Kaminaga, M

    2002-01-01

    The Japan Atomic Energy Research Institute (JAERI) and the High Energy Accelerator Research Organization (KEK) are promoting a construction plan of the Material-Life Science Facility, which is consisted of a Muon Science Facility and a Neutron Scattering Facility, in order to open up the new science fields. The Neutron Scattering Facility will be utilized for advanced fields of Material and Life science using high intensity neutron generated by the spallation reaction of a 1 MW pulsed proton beam and mercury target. Design of the spallation mercury target system aims to obtain high neutron performance with high reliability and safety. Since the target system is using mercury as the target material and contains large amount of radioactive spallation products, it is necessary to estimate reliability for strength of instruments in a mercury flow system during lifetime of the facility. Piping and components in the mercury flow system would be damaged by erosion with mercury flow, since these components will be we...

  7. Concentration of mercury in wheat samples stored with mercury tablets as preservative

    International Nuclear Information System (INIS)

    Lalit, B.Y.; Ramachandran, T.V.

    1977-01-01

    Tablets consisting of mercury in the form of a dull grey powder made by triturating mercury with chalk and sugar are used in Indian household for storing food-grains. The contamination of wheat samples by mercury, when stored with mercury tablets for period of upto four years has been assessed by using non-destructive neutron activation analysis. The details of the analytical procedure used have also been briefly described. The concentration of mercury in wheat increases with storage period. Loss of weight of mercury tablet is proportional to the storage period to a first approximation. In the present experiment, the average weight loss at the and end of first year was 0.009716 g corresponding to 6 ppm in wheat. (T.G.)

  8. Hidden sources of mercury in clinical laboratories.

    Science.gov (United States)

    Alvarez-Chavez, C R; Federico-Perez, R A; Gomez-Alvarez, A; Velazquez-Contreras, L E; Perez-Rios, R

    2014-09-01

    The healthcare sector is an important contributor to mercury (Hg) pollution because of the potential presence of mercury in thermometers, blood pressure cuffs, amalgams, etc. There are also other potential sources of mercury in this sector which are used frequently and in high volumes where the presence of the metal is not obvious and which might be collectively contributing to pollution. For instance, some chemicals used for the clinical diagnosis of illness may contain mercury. The goal of this study was to investigate potential sources of mercury pollution, which originate from clinical laboratory discharges, using an exploratory approach. The focus was on the residue generated during automatic analysis of patients' bodily fluids at a medical center in Hermosillo, Sonora, Mexico. This study shows an overview of what might be happening in the region or the country related to non-obvious sources of mercury in the healthcare sector. The results showed measurable levels of mercury in the residues coming from urine sediment analysis. These amounts do not exceed the maximum allowed by Mexican environmental regulations; nevertheless, the frequency and cumulative volume of residues generated, combined with the potential for persistence and the bioaccumulation of mercury in the environment, warrant attention. The work carried out in this study is being taken as a model for future studies for pollution prevention in the healthcare sector with the goal of measuring mercury emissions to the environment from clinical laboratory wastewater, including identifying sources which--while not obvious--could be important given the frequency and volume of their use in the clinical diagnosis.

  9. GREEN CHEMISTRY APPLICATION FOR THE SYNTHESIS OF (1-N-4’-METHOXYBENZYL-1,10-PHENANTHROLINIUM BROMIDE

    Directory of Open Access Journals (Sweden)

    Maulidan Firdaus

    2010-06-01

    Full Text Available A simple, energy-efficient, and relatively quick synthetic procedure for the synthesis of (1-N-4'-methoxybenzyl-1,10-phenanthrolinium bromide, based on green chemistry principles has been carried out. The synthesis was started by solvent-free reduction of p-anisaldehyde with NaBH4 to give 4-methoxybenzyl alcohol in 98% yield to be followed by solvent-free treatment of the resulted alcohol with PBr3 to yield 4-methoxybenzyl bromide (86%. Furthermore, the obtained bromide was reacted with 1,10-phenanthroline in acetone at reflux for 12 h to give the phenanthrolinium salt target in 68% yield.   Keywords: green chemistry, p-anisaldehyde, (1-N-4'-methoxybenzyl-1,10-phenanthrolinium bromide

  10. Estimating Potential Increased Bladder Cancer Risk Due to Increased Bromide Concentrations in Sources of Disinfected Drinking Waters - slides

    Science.gov (United States)

    Public water systems are increasingly facing higher bromide levels in their source waters from anthropogenic contamination through coal-fired powerplants, conventional oil and gas extraction, and hydraulic fracturing. Climate change is likely to exacerbate this in coming years. W...

  11. Estimating Potential Increased Bladder Cancer Risk Due to Increased Bromide Concentrations in Sources of Disinfected Drinking Waters

    Science.gov (United States)

    Public water systems are increasingly facing higher bromide levels in their source waters from anthropogenic contamination through coal-fired power plants, conventional oil and gas extraction, and hydraulic fracturing. Climate change is likely to exacerbate this in coming years. ...

  12. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, No Stack, More than 8 Hours

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  13. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Horizontal Stacks, 8 Hours or Less

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  14. Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, No Stack, 8 Hours or Less

    Science.gov (United States)

    This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

  15. The tropical African mercury anomaly: lower than expected mercury concentrations in fish and human hair.

    Science.gov (United States)

    Black, Frank J; Bokhutlo, Thethela; Somoxa, Aaron; Maethamako, Mothusi; Modisaemang, Ontlogetse; Kemosedile, Thebe; Cobb-Adams, Cristina; Mosepele, Ketlhatlogile; Chimbari, Moses

    2011-04-15

    Mercury is a neurotoxin and global pollutant, and wetlands and newly flooded areas are known to be sites of enhanced production of monomethylmercury, the form of mercury that is readily biomagnified in aquatic food chains to potentially toxic levels. The Okavango Delta in Botswana, Southern Africa, is the largest inland delta in the world and a wetland ecosystem that experiences dramatic annual flooding of large tracts of seasonal floodplains. The Delta was, therefore, expected to be home to high mercury levels in fish and to be an area where local subsistence fishing communities would be at substantial risk of mercury toxicity from fish consumption. Total mercury concentrations measured in 27 species of fish from the Okavango Delta averaged (mean±s.d., wet weight) 19±19ng g(-1) in non-piscivorous fish, and 59±53ng g(-1) in piscivorous fish. These mercury concentrations are similar to those reported for fish from lakes in other areas of tropical Africa, demonstrating that not all wetlands are sites of elevated mercury concentrations in biota. Even more intriguing is that concentrations of mercury in fish from across tropical Africa are systematically and substantially lower than those typically reported for fish from freshwater ecosystems elsewhere globally. The reasons for this apparent "African mercury anomaly" are unclear, but this finding poses a unique opportunity to improve our understanding of mercury's biogeochemical cycling in the environment. Mercury concentrations measured in human hair collected in subsistence fishing communities in the Okavango Delta were similarly low (0.21±0.22μg g(-1) dry weight) despite high levels of fish consumption, and reflect the low mercury concentrations in the fish here. Copyright © 2010 Elsevier B.V. All rights reserved.

  16. Methyl mercury, but not inorganic mercury, associated with higher blood pressure during pregnancy.

    Science.gov (United States)

    Wells, Ellen M; Herbstman, Julie B; Lin, Yu Hong; Hibbeln, Joseph R; Halden, Rolf U; Witter, Frank R; Goldman, Lynn R

    2017-04-01

    Prior studies addressing associations between mercury and blood pressure have produced inconsistent findings; some of this may result from measuring total instead of speciated mercury. This cross-sectional study of 263 pregnant women assessed total mercury, speciated mercury, selenium, and n-3 polyunsaturated fatty acids in umbilical cord blood and blood pressure during labor and delivery. Models with a) total mercury or b) methyl and inorganic mercury were evaluated. Regression models adjusted for maternal age, race/ethnicity, prepregnancy body mass index, neighborhood income, parity, smoking, n-3 fatty acids and selenium. Geometric mean total, methyl, and inorganic mercury concentrations were 1.40µg/L (95% confidence interval: 1.29, 1.52); 0.95µg/L (0.84, 1.07); and 0.13µg/L (0.10, 0.17), respectively. Elevated systolic BP, diastolic BP, and pulse pressure were found, respectively, in 11.4%, 6.8%, and 19.8% of mothers. In adjusted multivariable models, a one-tertile increase of methyl mercury was associated with 2.83mmHg (0.17, 5.50) higher systolic blood pressure and 2.99mmHg (0.91, 5.08) higher pulse pressure. In the same models, an increase of one tertile of inorganic mercury was associated with -1.18mmHg (-3.72, 1.35) lower systolic blood pressure and -2.51mmHg (-4.49, -0.53) lower pulse pressure. No associations were observed with diastolic pressure. There was a non-significant trend of higher total mercury with higher systolic blood pressure. We observed a significant association of higher methyl mercury with higher systolic and pulse pressure, yet higher inorganic mercury was significantly associated with lower pulse pressure. These results should be confirmed with larger, longitudinal studies. Copyright © 2017 Elsevier Inc. All rights reserved.

  17. Isolation, screening and identification of mercury resistant bacteria from mercury contaminated soil

    OpenAIRE

    Kowalczyk Anna; Wilińska Magdalena; Chyc Marek; Bojko Monika; Latowski Dariusz

    2016-01-01

    New bacterial strains resistant to high concentration of mercury were obtained and character iz ed focusing on their potential application in bioremediation. The biological material was isolated from soil contaminated with mercury. The ability to removal of Hg from the liquid medium and the effect of the various pH and mercury concentrations in the environment on bacterial strains growth kinetics were tested. The selected strains were identified by analysis of the 16S ribosome subunit coding ...

  18. Mercury fluxes through the sediment water interface and bioavailability of mercury in southern Baltic Sea sediments

    Directory of Open Access Journals (Sweden)

    Jacek Bełdowski

    2009-06-01

    Full Text Available Sediment cores collected in several areas of the southern Baltic were analysed for total mercury (HgTOT and five operationally defined mercury fractions: HgA - contained in pore waters, HgF - bound to fulvic acids, HgH - bound to humic acids, HgS - bound to sulphide, and HgR - residual. An effort was made to quantify mercury fluxes at the sediment/water interface in the study area. Net mercury input, calculated on the basis of sedimentation rate and concentration in the uppermost sediments, ranged from 1 to 5.5 ng cm-2 year-1. Mercury remobilisation from sediments due to diffusion and resuspension was calculated from the proportion of labile mercury and the velocity of near-bottom currents. The results showed that the return soluble and particulate fluxes of mercury from the sediments to the water column constitute a substantial proportion of the input (20-50%, and are slightly higher than those found in pristine areas, although they are less than the values recorded in areas with a history of mercury contamination. In addition, an index was developed to assess the methylation potential of mercury in sediments. Mercury contained in pore waters, and mercury bound to fulvic and humic acids together with Loss on Ignition were used to calculate the semi-quantitative methylation potential (Pm. Despite the simplicity of this approach, Pm correlates well with methyl mercury in fish from the study area.full, complete article (PDF - compatibile with Acrobat 4.0, 291.3 kB

  19. Prostate cancer and toxicity from critical use exemptions of methyl bromide: Environmental protection helps protect against human health risks

    Directory of Open Access Journals (Sweden)

    Budnik Lygia T

    2012-01-01

    Full Text Available Abstract Background Although ozone-depleting methyl bromide was destined for phase-out by 2005, it is still widely applied as a consequence of various critical-use-exemptions and mandatory international regulations aiming to restrict the spread of pests and alien species (e.g. in globalized transport and storage. The withdrawal of methyl bromide because of its environmental risk could fortuitously help in the containment of its human toxicity. Methods We performed a systematic review of the literature, including in vitro toxicological and epidemiological studies of occupational and community exposure to the halogenated hydrocarbon pesticide methyl bromide. We focused on toxic (especially chronic or carcinogenic effects from the use of methyl bromide, on biomonitoring data and reference values. Eligible epidemiological studies were subjected to meta-analysis. Results Out of the 542 peer reviewed publications between 1990-2011, we found only 91 referring to toxicity of methyl bromide and 29 using the term "carcinogenic", "neoplastic" or "mutagenic". Several studies provide new additional data pertaining to the mechanistic aspects of methyl bromide toxicity. Few studies have performed a detailed exposure assessment including biomonitoring. Three evaluated epidemiological studies assessed a possible association between cancer and methyl bromide. Overall, exposure to methyl bromide is associated with an increased risk of prostate cancer OR, 1.21; 95% CI (0,98-1.49, P = 0.076. Two epidemiological studies have analyzed environmental, non-occupational exposure to methyl bromide providing evidence for its health risk to the general public. None of the epidemiological studies addressed its use as a fumigant in freight containers, although recent field and case reports do refer to its toxic effects associated with its use in shipping and storage. Conclusions Both the epidemiological evidence and toxicological data suggest a possible link between methyl

  20. determination of mercury content in milk powder

    International Nuclear Information System (INIS)

    Jovchev, M.; Grigorov, T.; Apostolov, D.

    1985-01-01

    Four samples of humanized full cream cow milk powder of Bulgarian origin for new-born, sucklings, small children and soured milk powder were activated for 18-24 h in a neutron flux of 5.10 12 , resp. 2.10 13 n/cm 2 .sec in quartz ampules. The samples were activated without preliminary lyophilization, thus avoiding possible mistakes from mercury losses. Ag-110m, being eliminated in the amalgam, was not an obstacle to the mercury determination. The results obtained for the mercury content are in the same order as in other investigations and many times lower than the admissible norm for foodstuffs - 50 ppb

  1. Effect of mercury on algal growth rates

    Energy Technology Data Exchange (ETDEWEB)

    Hannan, P.J.; Patouillet, C.

    1972-01-01

    In experiments with one freshwater (Chlorella pyrenoidosa) and three marine organisms (Phaeodactylum tricornutum, Cyclotella nana, and Chaetoceras gavestonensis), mercury was more toxic than the other metals tested (silver, cadmium, lead, and copper); and its toxicity is comparatively irreversible. Growth was monitored by changes in fluorescence of the cultures over a 3-day test period. The toxicity of the mercury varied inversely with the concentrations of nutrients present. Preliminary experiments indicate that mercury in the form of mercuric chloride is more toxic than as dimethylmercury. 12 references, 3 figures, 1 table.

  2. Conditioning of spent mercury by amalgamation

    International Nuclear Information System (INIS)

    Yim, S. P.; Shon, J. S.; An, B. G.; Lee, H. J.; Lee, J. W.; Ji, C. G.; Kim, S. H.; Yoon, J. H.; Yang, M. S.

    2002-01-01

    Solidification by amalgamation was performed to immobilize and stabilize the liquid spent mercury. First, the appropriate metal and alloy which can convert liquid mercury into a solid form of amalgam were selected through initial tests. The amalgam form, formulated in optimum composition, was characterized and subjected to performance tests including compressive strength, water immersion, leachability and initial vaporization rate to evaluate mechanical integrity, durability and leaching properties. Finally, bench scale amalgamation trial was conducted with about 1 kg of spent mercury to verify the feasibility of amalgamation method

  3. A self-focusing mercury jet target

    CERN Document Server

    Johnson, C

    2002-01-01

    Mercury jet production targets have been studied in relation to antiproton production and, more recently, pion production for a neutrino factory. There has always been a temptation to include some self-focusing of the secondaries by passing a current through the mercury jet analogous to the already proven lithium lens. However, skin heating of the mercury causes fast vaporization leading to the development of a gliding discharge along the surface of the jet. This external discharge can, nevertheless, provide some useful focusing of the secondaries in the case of the neutrino factory. The technical complications must not be underestimated.

  4. Mercury Thermal Hydraulic Loop (MTHL) Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Felde, David K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Crye, Jason Michael [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wendel, Mark W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yoder, Jr, Graydon L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Farquharson, George [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jallouk, Philip A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); McFee, Marshall T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pointer, William David [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ruggles, Art E. [Univ. of Tennessee, Knoxville, TN (United States); Carbajo, Juan J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-03-01

    The Spallation Neutron Source (SNS) is a high-power linear accelerator built at Oak Ridge National Laboratory (ORNL) which incorporates the use of a flowing liquid mercury target. The Mercury Thermal Hydraulic Loop (MTHL) was constructed to investigate and verify the heat transfer characteristics of liquid mercury in a rectangular channel. This report provides a compilation of previously reported results from the water-cooled and electrically heated straight and curved test sections that simulate the geometry of the window cooling channel in the target nose region.

  5. Physical properties of the planet Mercury

    Science.gov (United States)

    Clark, Pamela E.

    1988-01-01

    The global physical properties of Mercury are summarized with attention given to its figure and orbital parameters. The combination of properties suggests that Mercury has an extensive iron-rich core, possibly with a still-functioning dynamo, which is 42 percent of the interior by volume. Mercury's three major axes are comparable in size, indicating that the planet is a triaxial ellipsoid rather than an oblate spheroid. In terms of the domination of its surface by an intermediate plains terrane, it is more Venus- or Mars-like; however, due to the presence of a large metallic magnetic core, its interior may be more earth-like.

  6. MESSENGER'S First and Second Flybys of Mercury

    Science.gov (United States)

    Slavin, James A.

    2009-01-01

    The MESSENGER mission to Mercury offers our first opportunity to explore this planet's miniature magnetosphere since Mariner 10's brief fly-bys in 1974-5. The magnetosphere of Mercury is the smallest in the solar system with its magnetic field typically standing off the solar wind only approximately 1000 km above the surface. An overview of the MESSENGER mission and its January 14th and October 6th, 2008 close flybys of Mercury will be provided. Primary science objectives and the science instrumentation will be described. Initial results from MESSENGER will be discussed with an emphasis on the magnetic field and charged particle measurements.

  7. Inorganic mercury causes pancreatic β-cell death via the oxidative stress-induced apoptotic and necrotic pathways

    International Nuclear Information System (INIS)

    Chen Yawen; Huang Chunfa; Yang Chingyao; Yen Chengchieh; Tsai Kehsung; Liu Shinghwa

    2010-01-01

    Mercury is a well-known highly toxic metal. In this study, we characterize and investigate the cytotoxicity and its possible mechanisms of inorganic mercury in pancreatic β-cells. Mercury chloride (HgCl 2 ) dose-dependently decreased the function of insulin secretion and cell viability in pancreatic β-cell-derived HIT-T15 cells and isolated mouse pancreatic islets. HgCl 2 significantly increased ROS formation in HIT-T15 cells. Antioxidant N-acetylcysteine effectively reversed HgCl 2 -induced insulin secretion dysfunction in HIT-T15 cells and isolated mouse pancreatic islets. Moreover, HgCl 2 increased sub-G1 hypodiploids and annexin-V binding in HIT-T15 cells, indicating that HgCl 2 possessed ability in apoptosis induction. HgCl 2 also displayed several features of mitochondria-dependent apoptotic signals including disruption of the mitochondrial membrane potential, increase of mitochondrial cytochrome c release and activations of poly (ADP-ribose) polymerase (PARP) and caspase 3. Exposure of HIT-T15 cells to HgCl 2 could significantly increase both apoptotic and necrotic cell populations by acridine orange/ethidium bromide dual staining. Meanwhile, HgCl 2 could also trigger the depletion of intracellular ATP levels and increase the LDH release from HIT-T15 cells. These HgCl 2 -induced cell death-related signals could be significantly reversed by N-acetylcysteine. The intracellular mercury levels were markedly elevated in HgCl 2 -treated HIT-T15 cells. Taken together, these results suggest that HgCl 2 -induced oxidative stress causes pancreatic β-cell dysfunction and cytotoxicity involved the co-existence of apoptotic and necrotic cell death.

  8. Injurious effect of mercury vapor from bichloride of mercury in soil of rose houses

    Energy Technology Data Exchange (ETDEWEB)

    Zimmerman, P.W.; Crocker, W.

    1933-01-01

    Addition of mercuric chloride, or corrosive sublimate, to Rose soil for killing earthworms may injure the Roses. The organic matter of the soil reduces the bichloride to metallic mercury and the vapors of the mercury rise into the air and kill the buds and peduncles. When the soil is rich in tankage or other organic matter, the rate of reduction of the bichloride is increased and thereby the severity of the injury intensified. If a container of metallic mercury is set in an enclosed chamber with Rose plants, severe injuries of the type mentioned below soon appear. The Briarcliff Rose is especially susceptible to mercury injury. 1 figure.

  9. Mercury Information Clearinghouse. Quarterly 3: advanced and developmental mercury control technologies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    Advanced mercury control technologies for coal-fired electric utilities are reviewed. The technologies evaluated are at various stages of development and most have been tested under limited operational conditions. The following technologies are described: K-Fuel and K-Fuel Plus pre-combustion technology, combustion modification and in situ generation of sorbents, new sorbent developments, direct bromine injection, MerCAP{sup {trademark}} (Mercury Control via Adsorption Process, Gore felt filter bag inserts, EnviroScrub Pahlman{sup {trademark}} process, combined oxidation of NO{sub x} and mercury, and mercury control with the Advanced Hybrid{trademark} filter. 36 refs., 1 fig.

  10. Solubility of helium in mercury for bubbling technology of the spallation neutron mercury target

    International Nuclear Information System (INIS)

    Hasegawa, S.; Naoe, T.; Futakawa, M.

    2010-01-01

    The pitting damage of mercury target container that originates in the pressure wave excited by the proton beam incidence becomes a large problem to reach the high-power neutron source in JSNS and SNS. The lifetime of mercury container is decreased remarkably by the pitting damage. As one of solutions, the pressure wave is mitigated by injecting the helium micro bubbles in mercury. In order to inject the helium micro bubbles into mercury, it is important to understand the characteristic of micro bubbles in mercury. The solubility of mercury-helium system is a key factor to decide bubbling conditions, because the disappearance behavior, i.e. the lifetime of micro bubbles, depends on the solubility. In addition, the bubble generation method is affected by it. Moreover, the experimental data related to the solubility of helium in mercury hardly exist. In this work, the solubility was obtained experimentally by measuring precisely the pressure drop of the gas that is facing to mercury surface. The pressure drop was attributed to the helium dissolution into mercury. Based on the measured solubility, the lifetime of micro bubbles and the method of the bubble generation is estimated using the solubility data.

  11. Inorganic mercury exposure, mercury-copper interaction, and DMPS treatment in rats.

    OpenAIRE

    Blanusa, M; Prester, L; Radić, S; Kargacin, B

    1994-01-01

    The aim of this study was to evaluate the efficiency of oral treatment with sodium 2,3-dimercaptopropane-1-sulfonate (DMPS) on reducing mercury deposits in rat kidney after chronic exposure to inorganic mercury. The effect on kidney copper levels was also evaluated. The results showed that after two months of exposure to 50 ppm of mercury (as mercuric chloride) the concentration of mercury in the kidney was 124 micrograms/g wet tissue. At the same time copper concentration rose from 11 to 77 ...

  12. Mercury nano-trap for effective and efficient removal of mercury(II) from aqueous solution

    Science.gov (United States)

    Li, Baiyan; Zhang, Yiming; Ma, Dingxuan; Shi, Zhan; Ma, Shengqian

    2014-11-01

    Highly effective and highly efficient decontamination of mercury from aqueous media remains a serious task for public health and ecosystem protection. Here we report that this task can be addressed by creating a mercury ‘nano-trap’ as illustrated by functionalizing a high surface area and robust porous organic polymer with a high density of strong mercury chelating groups. The resultant porous organic polymer-based mercury ‘nano-trap’ exhibits a record-high saturation mercury uptake capacity of over 1,000 mg g-1, and can effectively reduce the mercury(II) concentration from 10 p.p.m. to the extremely low level of smaller than 0.4 p.p.b. well below the acceptable limits in drinking water standards (2 p.p.b.), and can also efficiently remove >99.9% mercury(II) within a few minutes. Our work therefore presents a new benchmark for mercury adsorbent materials and provides a new perspective for removing mercury(II) and also other heavy metal ions from contaminated water for environmental remediation.

  13. Tundra uptake of atmospheric elemental mercury drives Arctic mercury pollution

    Science.gov (United States)

    Obrist, Daniel; Agnan, Yannick; Jiskra, Martin; Olson, Christine L.; Colegrove, Dominique P.; Hueber, Jacques; Moore, Christopher W.; Sonke, Jeroen E.; Helmig, Detlev

    2017-07-01

    Anthropogenic activities have led to large-scale mercury (Hg) pollution in the Arctic. It has been suggested that sea-salt-induced chemical cycling of Hg (through ‘atmospheric mercury depletion events’, or AMDEs) and wet deposition via precipitation are sources of Hg to the Arctic in its oxidized form (Hg(II)). However, there is little evidence for the occurrence of AMDEs outside of coastal regions, and their importance to net Hg deposition has been questioned. Furthermore, wet-deposition measurements in the Arctic showed some of the lowest levels of Hg deposition via precipitation worldwide, raising questions as to the sources of high Arctic Hg loading. Here we present a comprehensive Hg-deposition mass-balance study, and show that most of the Hg (about 70%) in the interior Arctic tundra is derived from gaseous elemental Hg (Hg(0)) deposition, with only minor contributions from the deposition of Hg(II) via precipitation or AMDEs. We find that deposition of Hg(0)—the form ubiquitously present in the global atmosphere—occurs throughout the year, and that it is enhanced in summer through the uptake of Hg(0) by vegetation. Tundra uptake of gaseous Hg(0) leads to high soil Hg concentrations, with Hg masses greatly exceeding the levels found in temperate soils. Our concurrent Hg stable isotope measurements in the atmosphere, snowpack, vegetation and soils support our finding that Hg(0) dominates as a source to the tundra. Hg concentration and stable isotope data from an inland-to-coastal transect show high soil Hg concentrations consistently derived from Hg(0), suggesting that the Arctic tundra might be a globally important Hg sink. We suggest that the high tundra soil Hg concentrations might also explain why Arctic rivers annually transport large amounts of Hg to the Arctic Ocean.

  14. Tundra uptake of atmospheric elemental mercury drives Arctic mercury pollution.

    Science.gov (United States)

    Obrist, Daniel; Agnan, Yannick; Jiskra, Martin; Olson, Christine L; Colegrove, Dominique P; Hueber, Jacques; Moore, Christopher W; Sonke, Jeroen E; Helmig, Detlev

    2017-07-12

    Anthropogenic activities have led to large-scale mercury (Hg) pollution in the Arctic. It has been suggested that sea-salt-induced chemical cycling of Hg (through 'atmospheric mercury depletion events', or AMDEs) and wet deposition via precipitation are sources of Hg to the Arctic in its oxidized form (Hg(ii)). However, there is little evidence for the occurrence of AMDEs outside of coastal regions, and their importance to net Hg deposition has been questioned. Furthermore, wet-deposition measurements in the Arctic showed some of the lowest levels of Hg deposition via precipitation worldwide, raising questions as to the sources of high Arctic Hg loading. Here we present a comprehensive Hg-deposition mass-balance study, and show that most of the Hg (about 70%) in the interior Arctic tundra is derived from gaseous elemental Hg (Hg(0)) deposition, with only minor contributions from the deposition of Hg(ii) via precipitation or AMDEs. We find that deposition of Hg(0)-the form ubiquitously present in the global atmosphere-occurs throughout the year, and that it is enhanced in summer through the uptake of Hg(0) by vegetation. Tundra uptake of gaseous Hg(0) leads to high soil Hg concentrations, with Hg masses greatly exceeding the levels found in temperate soils. Our concurrent Hg stable isotope measurements in the atmosphere, snowpack, vegetation and soils support our finding that Hg(0) dominates as a source to the tundra. Hg concentration and stable isotope data from an inland-to-coastal transect show high soil Hg concentrations consistently derived from Hg(0), suggesting that the Arctic tundra might be a globally important Hg sink. We suggest that the high tundra soil Hg concentrations might also explain why Arctic rivers annually transport large amounts of Hg to the Arctic Ocean.

  15. Rethinking mercury: the role of selenium in the pathophysiology of mercury toxicity.

    Science.gov (United States)

    Spiller, Henry A

    2018-05-01

    There is increasing evidence that the pathophysiological target of mercury is in fact selenium, rather than the covalent binding of mercury to sulfur in the body's ubiquitous sulfhydryl groups. The role of selenium in mercury poisoning is multifaceted, bidirectional, and central to understanding the target organ toxicity of mercury. An initial search was performed using Medline/PubMed, Toxline, Google Scholar, and Google for published work on mercury and selenium. These searches yielded 2018 citations. Publications that did not evaluate selenium status or evaluated environmental status (e.g., lake or ocean sediment) were excluded, leaving approximately 500 citations. This initial selection was scrutinized carefully and 117 of the most relevant and representative references were selected for use in this review. Binding of mercury to thiol/sulfhydryl groups: Mercury has a lower affinity for thiol groups and higher affinity for selenium containing groups by several orders of magnitude, allowing for binding in a multifaceted way. The established binding of mercury to thiol moieties appears to primarily involve the transport across membranes, tissue distribution, and enhanced excretion, but does not explain the oxidative stress, calcium dyshomeostasis, or specific organ injury seen with mercury. Effects of mercury on selenium and the role this plays in the pathophysiology of mercury toxicity: Mercury impairs control of intracellular redox homeostasis with subsequent increased intracellular oxidative stress. Recent work has provided convincing evidence that the primary cellular targets are the selenoproteins of the thioredoxin system (thioredoxin reductase 1 and thioredoxin reductase 2) and the glutathione-glutaredoxin system (glutathione peroxidase). Mercury binds to the selenium site on these proteins and permanently inhibits their function, disrupting the intracellular redox environment. A number of other important possible target selenoproteins have been identified

  16. Mercury pollution in Wuchuan mercury mining area, Guizhou, Southwestern China: the impacts from large scale and artisanal mercury mining.

    Science.gov (United States)

    Li, Ping; Feng, Xinbin; Qiu, Guangle; Shang, Lihai; Wang, Shaofeng

    2012-07-01

    To evaluate the environmental impacts from large scale mercury mining (LSMM) and artisanal mercury mining (AMM), total mercury (THg) and methyl mercury (MeHg) were determined in mine waste, ambient air, stream water and soil samples collected from Wuchuan mercury (Hg) mining area, Guizhou, Southwestern China. Mine wastes from both LSMM and AMM contained high THg concentrations, which are important Hg contamination sources to the local environment. Total gaseous mercury (TGM) concentrations in the ambient air near AMM furnaces were highly elevated, which indicated that AMM retorting is a major source of Hg emission. THg concentrations in the stream water varied from 43 to 2100 ng/L, where the elevated values were mainly found in the vicinity of AMM and mine waste heaps of LSMM. Surface soils were seriously contaminated with Hg, and land using types and organic matter played an important role in accumulation and transportation of Hg in soil. The results indicated heavy Hg contaminations in the study area, which were resulted from both LSMM and AMM. The areas impacted by LSMM were concentrated in the historical mining and smelting facilities, while Hg pollution resulted from AMM can be distributed anywhere in the Hg mining area. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Mercury content in electrum from artisanal mining site of Mongolia

    Energy Technology Data Exchange (ETDEWEB)

    Murao, Satoshi [Geological Survey of Japan, AIST, Higashi 1-1-1, No. 7, Tsukuba 305-8567 (Japan)]. E-mail: s.murao@aist.go.jp; Naito, Kazuki [Geological Survey of Japan, AIST, Higashi 1-1-1, No. 7, Tsukuba 305-8567 (Japan); Dejidmaa, Gunchin [Geological Information Center, Mineral and Petroleum Resources Authority of Mongolia, State Building No. 5, Ulaanbaatar (Mongolia); Sie, Soey H. [CSIRO, P.O. Box 136, North Ryde, NSW 1670 (Australia)

    2006-08-15

    In Mongolia, artisanal gold mining, modern gold rush, in which people use mercury to extract gold, is being proliferated rapidly and the mercury contamination of mining site is becoming a serious social issue. For the risk assessment of mercury, it is necessary to understand how much mercury is introduced to the environment from what kind of materials during mining activity. It is already known that major contribution of the contamination comes from mercury that was bought at shops and brought to mining sites by miners. However, no information is available on how much mercury is removed from electrum (natural gold grain) to the environment. Since gold deposit is always accompanied by mercury anomaly, it is anticipated that electrum grains contain some amount of mercury of natural origin, and this mercury (primary mercury) contributes to some extent to the contamination. In order to clarify how much mercury is incorporated in electrum grains, micro-PIXE at CSIRO was used for grain-by-grain analysis. The result showed that electrum from study area contains mercury up to 8260 ppm. It is concluded that for the risk management of mercury contamination, release of natural mercury from electrum grains during smelting must not be ignored.

  18. Mercury content in electrum from artisanal mining site of Mongolia

    Science.gov (United States)

    Murao, Satoshi; Naito, Kazuki; Dejidmaa, Gunchin; Sie, Soey H.

    2006-08-01

    In Mongolia, artisanal gold mining, modern gold rush, in which people use mercury to extract gold, is being proliferated rapidly and the mercury contamination of mining site is becoming a serious social issue. For the risk assessment of mercury, it is necessary to understand how much mercury is introduced to the environment from what kind of materials during mining activity. It is already known that major contribution of the contamination comes from mercury that was bought at shops and brought to mining sites by miners. However, no information is available on how much mercury is removed from electrum (natural gold grain) to the environment. Since gold deposit is always accompanied by mercury anomaly, it is anticipated that electrum grains contain some amount of mercury of natural origin, and this mercury (primary mercury) contributes to some extent to the contamination. In order to clarify how much mercury is incorporated in electrum grains, micro-PIXE at CSIRO was used for grain-by-grain analysis. The result showed that electrum from study area contains mercury up to 8260 ppm. It is concluded that for the risk management of mercury contamination, release of natural mercury from electrum grains during smelting must not be ignored.

  19. Bioavailability and stability of mercury sulfide in Armuchee (USA) soil

    International Nuclear Information System (INIS)

    Han, Fengxiang; Shiyab, Safwan; Su, Yi; Monts, David L.; Waggoner, Charles A.; Matta, Frank B.

    2007-01-01

    Because of the adverse effects of elemental mercury and mercury compounds upon human health, the U.S. Department of Energy (DOE) is engaged in an on-going effort to monitor and remediate mercury-contaminated DOE sites. In order to more cost effectively implement those extensive remediation efforts, it is necessary to obtain an improved understanding of the role that mercury and mercury compounds play in the ecosystem. We have conducted pilot scale experiments to study the bioavailability of mercury sulfide in an Armuchee (eastern US ) soil. The effects of plants and incubation time on chemical stability and bioavailability of HgS under simulated conditions of the ecosystem have been examined, as has the dynamics of the dissolution of mercury sulfide by various extractants. The results show that mercury sulfide in contaminated Armuchee soil was still to some extent bioavailable to plants. After planting, soil mercury sulfide is more easily dissolved by both 4 M and 12 M nitric acid than pure mercury sulfide reagent. Dissolution kinetics of soil mercury sulfide and pure chemical reagent by nitric acid are different. Mercury release by EDTA from HgS-contaminated soil increased with time of reaction and soil mercury level. Chelating chemicals increase the solubility and bioavailability of mercury in HgS-contaminated soil. (authors)

  20. Mercury content in electrum from artisanal mining site of Mongolia

    International Nuclear Information System (INIS)

    Murao, Satoshi; Naito, Kazuki; Dejidmaa, Gunchin; Sie, Soey H.

    2006-01-01

    In Mongolia, artisanal gold mining, modern gold rush, in which people use mercury to extract gold, is being proliferated rapidly and the mercury contamination of mining site is becoming a serious social issue. For the risk assessment of mercury, it is necessary to understand how much mercury is introduced to the environment from what kind of materials during mining activity. It is already known that major contribution of the contamination comes from mercury that was bought at shops and brought to mining sites by miners. However, no information is available on how much mercury is removed from electrum (natural gold grain) to the environment. Since gold deposit is always accompanied by mercury anomaly, it is anticipated that electrum grains contain some amount of mercury of natural origin, and this mercury (primary mercury) contributes to some extent to the contamination. In order to clarify how much mercury is incorporated in electrum grains, micro-PIXE at CSIRO was used for grain-by-grain analysis. The result showed that electrum from study area contains mercury up to 8260 ppm. It is concluded that for the risk management of mercury contamination, release of natural mercury from electrum grains during smelting must not be ignored

  1. Environmental chemistry and toxicology of mercury

    National Research Council Canada - National Science Library

    Liu, Guangliang; Cai, Yong; O'Driscoll, Nelson J

    2012-01-01

    ... employed in recent studies. The coverage discusses the environmental behavior and toxicological effects of mercury on organisms, including humans, and provides case studies at the end of each chapter...

  2. Filter for isotopic alteration of mercury vapor

    Science.gov (United States)

    Grossman, Mark W.; George, William A.

    1989-01-01

    A filter for enriching the .sup.196 Hg content of mercury, including a reactor, a low pressure electric discharge lamp containing a fill of mercury and an inert gas. A filter is arranged concentrically around the lamp. The reactor is arranged around said filter, whereby radiation from said lamp passes through the filter and into said reactor. The lamp, the filter and the reactor are formed of quartz, and are transparent to ultraviolet light. The .sup.196 Hg concentration in the mercury fill is less than that which is present in naturally occurring mercury, that is less than about 0.146 atomic weight percent. Hydrogen is also included in the fill and serves as a quenching gas in the filter, the hydrogen also serving to prevent disposition of a dark coating on the interior of the filter.

  3. Chemistry of impact events on Mercury

    Science.gov (United States)

    Berezhnoy, Alexey A.

    2018-01-01

    Based on the equilibrium thermochemical approach and quenching theory, formation of molecules and dust grains in impact-produced clouds formed after collisions between meteoroids and Mercury is considered. Based on observations of Al, Fe, and Mn atoms in the exosphere of Mercury and new results of studies of the elemental composition of the surface of Mercury, quenching temperatures and pressures of main chemical reactions and condensation of dust particles were estimated. The behavior of the main Na-, K-, Ca-, Fe-, Al-, Mn-, Mg-, Si-, Ti, Ni-, Cr-, Co, Zn-, O-, H-, S-, C-, Cl-, N-, and P-containing species delivered to the Hermean exosphere during meteoroid impacts was studied. The importance of meteoroid bombardment as a source of Na, K, Ca, Fe, Al, Mn, Mg, and O atoms in the exosphere of Mercury is discussed.

  4. Mercury in the South African environment

    CSIR Research Space (South Africa)

    Matooane, M

    2009-11-01

    Full Text Available ? Mercury, also known as quick silver, is ubiquitous in the environment ? Uses - Medical: medicines, thermometers, dental amalgam, etc. - Manufacturing industry: batteries, gold mining, chlorine production, cement production, etc. - Personal care...

  5. Mercury sorbent delivery system for flue gas

    Science.gov (United States)

    Klunder,; Edgar, B [Bethel Park, PA

    2009-02-24

    The invention presents a device for the removal of elemental mercury from flue gas streams utilizing a layer of activated carbon particles contained within the filter fabric of a filter bag for use in a flue gas scrubbing system.

  6. Environmental chemistry and toxicology of mercury

    National Research Council Canada - National Science Library

    Liu, Guangliang; Cai, Yong; O'Driscoll, Nelson J

    2012-01-01

    .... Bringing together information normally spread across several books, this text is unique in covering the entire mercury cycle and providing a baseline for what is known and what uncertainties remain...

  7. Mercury and halogens in coal--Their role in determining mercury emissions from coal combustion

    Science.gov (United States)

    Kolker, Allan; Quick, Jeffrey C.; Senior, Connie L.; Belkin, Harvey E.

    2012-01-01

    Mercury is a toxic pollutant. In its elemental form, gaseous mercury has a long residence time in the atmosphere, up to a year, allowing it to be transported long distances from emission sources. Mercury can be emitted from natural sources such as volcanoes, or from anthropogenic sources, such as coal-fired powerplants. In addition, all sources of mercury on the Earth's surface can re-emit it from land and sea back to the atmosphere, from which it is then redeposited. Mercury in the atmosphere is present in such low concentrations that it is not considered harmful. Once mercury enters the aquatic environment, however, it can undergo a series of biochemical transformations that convert a portion of the mercury originally present to methylmercury, a highly toxic organic form of mercury that accumulates in fish and birds. Many factors contribute to creation of methylmercury in aquatic ecosystems, including mercury availability, sediment and nutrient load, bacterial influence, and chemical conditions. In the United States, consumption of fish with high levels of methylmercury is the most common pathway for human exposure to mercury, leading the U.S. Environmental Protection Agency (EPA) to issue fish consumption advisories in every State. The EPA estimates that 50 percent of the mercury entering the atmosphere in the United States is emitted from coal-burning utility powerplants. An EPA rule, known as MATS (for Mercury and Air Toxics Standards), to reduce emissions of mercury and other toxic pollutants from powerplants, was signed in December 2011. The rule, which is currently under review, specifies limits for mercury and other toxic elements, such as arsenic, chromium, and nickel. MATS also places limits on emission of harmful acid gases, such as hydrochloric acid and hydrofluoric acid. These standards are the result of a 2010 detailed nationwide program by the EPA to sample stack emissions and thousands of shipments of coal to coal-burning powerplants. The United

  8. Gamma radiation stability studies of mercury fulminate

    International Nuclear Information System (INIS)

    Fondeur, F.F.

    2000-01-01

    Mercury fulminate completely decomposed in a gamma source (0.86 Mrad/h) after a dose of 208 Mrad. This exposure equates to approximately 2.4 years in Tank 15H and 4 years in Tank 12H, one of the vessels of concern. Since the tanks lost the supernatant cover layer more than a decade ago, this study suggests that any mercury fulminate or closely related energetic species decomposed long ago if ever formed

  9. Gamma radiation stability studies of mercury fulminate

    Energy Technology Data Exchange (ETDEWEB)

    Fondeur, F.F.

    2000-02-17

    Mercury fulminate completely decomposed in a gamma source (0.86 Mrad/h) after a dose of 208 Mrad. This exposure equates to approximately 2.4 years in Tank 15H and 4 years in Tank 12H, one of the vessels of concern. Since the tanks lost the supernatant cover layer more than a decade ago, this study suggests that any mercury fulminate or closely related energetic species decomposed long ago if ever formed.

  10. Stratigraphy and geologic history of Mercury

    International Nuclear Information System (INIS)

    Spudis, P.D.; Guest, J.E.

    1988-01-01

    The geologic evolution of Mercury based on the Mariner-10 mission data is discussed. As reconstructed through photogeological analysis of global geologic relations of rock-stratigraphic units, Mercury's geologic history is shown to involve intensive early impact bombardment and widespread resurfacing by volcanic lavas. Evidence is presented to indicate that this volcanic activity essentially ended as much as 3 Gyr ago, with most of the major geologic events being completed within the first 1 to 1.5 Gyr of Mercurian history

  11. Mercury's global evolution: New views from MESSENGER

    Science.gov (United States)

    Hauck, S. A., II; Byrne, P. K.; Denevi, B. W.; Grott, M.; McCoy, T.; Stanley, S.

    2015-12-01

    MESSENGER's exploration of Mercury has revealed the planet's rich and dynamic history and provided new constraints on the processes that control its internal evolution. Mercury's surface records evidence of an extensive geological history. This evidence includes resurfacing by impacts and volcanism prior to the end of the late heavy bombardment (LHB) and a subsequent rapid waning of effusive volcanism. Volcanism is an important indicator of the history of melt production. Thousands of globally distributed, contractional tectonic landforms collectively have accommodated a decrease in Mercury's radius of 5-7 km since the end of the LHB. Such contraction results from planetary cooling and crystallization within Mercury's metallic core. Measurements of surface chemistry have provided constraints on internal radiogenic heat production necessary to understand more fully Mercury's thermal evolution. Elemental abundances also reveal that Mercury is strongly chemically reduced, suggesting that the core's iron is alloyed with silicon as well as sulfur, which constrains the dynamics and crystallization of the metallic core. Magnetometer observations show that Mercury's dynamo-generated, dominantly dipolar field is displaced ~500 km northward along the rotation axis. Low-altitude magnetic field observations late in the mission led to the discovery of crustal magnetization in Mercury's ancient crust, dating to at least 3.7 Ga, which places a new constraint on the timing of the dynamo. Monte Carlo parameterized mantle convection models, constrained by these observations, indicate that for global contraction of 7 km or less, mantle convection persists to the present ~40% of the time, with the likelihood of modern convection decreasing with less global contraction. Slow present cooling in these models indicates that dynamo generation is strongly influenced by both a static layer at the top of the core and convective motions within the core driven by compositional buoyancy.

  12. Thermal elastic deformations of the planet Mercury.

    Science.gov (United States)

    Liu, H.-S.

    1972-01-01

    The variation in solar heating due to the resonance rotation of Mercury produces periodic elastic deformations on the surface of the planet. The thermal stress and strain fields under Mercury's surface are calculated after certain simplifications. It is found that deformations penetrate to a greater depth than the variation of solar heating, and that the thermal strain on the surface of the planet pulsates with an amplitude of .004 and a period of 176 days.

  13. Environmental costs of mercury pollution.

    Science.gov (United States)

    Hylander, Lars D; Goodsite, Michael E

    2006-09-01

    Mercury (Hg) has been used for millennia in many applications, primarily in artisanal mining and as an electrode in the chlor-alkali industry. It is anthropogenically emitted as a pollutant from coal fired power plants and naturally emitted, primarily from volcanoes. Its unique chemical characteristics enable global atmospheric transport and it is deposited after various processes, ultimately ending up in one of its final sinks, such as incorporated into deep sediment or bioaccumulated, primarily in the marine environment. All forms of Hg have been established as toxic, and there have been no noted biological benefits from the metal. Throughout time, there have been notable incidents of Hg intoxication documented, and the negative health effects have been documented to those chronically or acutely exposed. Today, exposure to Hg is largely diet or occupationally dependent, however, many are exposed to Hg from their amalgam fillings. This paper puts a tentative monetary value on Hg polluted food sources in the Arctic, where local, significant pollution sources are limited, and relates this to costs for strategies avoiding Hg pollution and to remediation costs of contaminated sites in Sweden and Japan. The case studies are compiled to help policy makers and the public to evaluate whether the benefits to the global environment from banning Hg and limiting its initial emission outweigh the benefits from its continued use or lack of control of Hg emissions. The cases we studied are relevant for point pollution sources globally and their remediation costs ranged between 2,500 and 1.1 million US dollars kg(-1) Hg isolated from the biosphere. Therefore, regulations discontinuing mercury uses combined with extensive flue gas cleaning for all power plants and waste incinerators is cost effective.

  14. Mercury

    Science.gov (United States)

    ... people never recover, but there has been some success in people who receive chelation treatment. References Sue ... ADAM Health Solutions. About MedlinePlus Site Map FAQs Customer Support Get email updates Subscribe to RSS Follow ...

  15. Crystal structure, DNA interaction and thermal analysis data of two new antimicrobial active binuclear cadmium and mercury complexes

    Science.gov (United States)

    Musavi, S. A.; Montazerozohori, M.; Masoudiasl, A.; Naghiha, R.; Joohari, S.; Assoud, A.

    2017-10-01

    Two new binuclear Schiff base complexes with the general formula [CdLBr(μ-Br)]2 (1) and [Hg2L(μ-I)2I2] (2) were prepared by the reaction of 2,2-dimethyl-N,N'- bis-(3-phenyl-allylidene)-propane-1,3-diamine (L), CdBr2 and HgI2. The crystal structure of two complexes was determined by X-ray crystallography. The common structures for four-coordinated compounds are square planar or the tetrahedral geometries, which is evaluated by the Houser angular index (τ4). In [CdLBr(μ-Br)]2 (1), each cadmium center is five-coordinated by two iminic nitrogen atoms from Schiff base ligand, two μ2-bridging bromide anions and one terminal coordinating bromide anion. The metal center in this centrosymmetric dimer has a distorted square-pyramidal geometry. [Hg2L(μ-I)2I2] (2) consists of two four-coordinated mercury centers with different coordination spheres (HgN2I2 for Hg1 and HgI4 for Hg2). The TG/DTG diagrams showed that both complexes were completely decomposed under a nitrogen atmosphere. Furthermore, antibacterial activities of compounds have been screened against various bacteria and fungi by Disk diffusion method. Mercury complex inhibited the growth of the microorganisms more efficient than cadmium complex. DNA cleavage potential of compounds was evaluated by agarose gel electrophoresis method. Finally, nano-structure cadmium complex was sono-chemically synthesized and applied as precursor for preparation of cadmium oxide nanoparticles.

  16. Detection of concealed mercury with thermal neutrons

    International Nuclear Information System (INIS)

    Bell, Z.W.

    1994-01-01

    In the United States today, governments at all levels and the citizenry are paying increasing attention to the effects, both real and hypothetical, of industrial activity on the environment. Responsible modem industries, reflecting this heightened public and regulatory awareness, are either substituting benign materials for hazardous ones, or using hazardous materials only under carefully controlled conditions. In addition, present-day environmental consciousness dictates that we deal responsibly with legacy wastes. The decontamination and decommissioning (D ampersand D) of facilities at which mercury was used or processed presents a variety of challenges. Elemental mercury is a liquid at room temperature and readily evaporates in air. In large mercury-laden buildings, droplets may evaporate from one area only to recondense in other cooler areas. The rate of evaporation is a function of humidity and temperature; consequently, different parts of a building may be sources or sinks of mercury at different times of the day or even the year. Additionally, although mercury oxidizes in air, the oxides decompose upon heating. Hence, oxides contained within pipes or equipment, may be decomposed when those pipes and equipment are cut with saws or torches. Furthermore, mercury seeps through the pores and cracks in concrete blocks and pads, and collects as puddles and blobs in void spaces within and under them

  17. Magnesium-rich Basalts on Mercury

    Science.gov (United States)

    Martel, L. M. V.

    2013-05-01

    X-ray and gamma-ray spectrometers on NASA's MESSENGER spacecraft are making key measurements regarding the composition and properties of the surface of Mercury, allowing researchers to more clearly decipher the planet's formation and geologic history. The origin of the igneous rocks in the crust of Mercury is the focus of recent research by Karen Stockstill-Cahill and Tim McCoy (National Museum of Natural History, Smithsonian Institution), along with Larry Nittler and Shoshana Weider (Carnegie Institution of Washington) and Steven Hauck II (Case Western Reserve University). Using the well-known MELTS computer code Stockstill-Cahill and coauthors worked with MESSENGER-derived and rock-analog compositions to constrain petrologic models of the lavas that erupted on the surface of Mercury. Rock analogs included a partial melt of the Indarch meteorite and a range of Mg-rich terrestrial rocks. Their work shows the lavas on Mercury are most similar to terrestrial magnesian basalt (with lowered FeO content). The implications of the modeling are that Mg-rich lavas came from high-temperature sources in Mercury's mantle and erupted at high temperature with exceptionally low viscosity into thinly bedded and laterally extensive flows, concepts open to further evaluation by laboratory experiments and by geologic mapping of Mercury's surface using MESSENGER's imaging system and laser altimeter to document flow features and dimensions.

  18. Mercury's Global Topography from Radar Ranging Data

    Science.gov (United States)

    Anderson, J. D.; Schubert, G.; Asmar, S. W.; Jurgens, R. F.; Lau, E. L.; Moore, W. B.; Slade, M. A., III; Standish, E. M., Jr.

    2001-01-01

    When Mercury's radius is expanded in Legendre functions to the second degree and order, the systematic error in radar ranging data is reduced substantially. Previously, data spanning an observing interval from 1966 to 1990 were used to infer an equatorial ellipticity (a - b)/a = (540 +/- 54) X 10(exp -6) and a center-of-figure minus center-of-mass offset of (640 +/- 78) m. The magnitude of this equatorial center of figure offset implies an excess crustal thickness of 12 km or less, comparable to the Moon's excess. By comparing the equatorial ellipticity with the Mariner 10 gravity field, and assuming Airy isostatic compensation, bounds on crustal thickness can be derived. Mercury's crustal thickness is in the range from 100 to 300 km. The Mercury radar ranging observing interval has been extended from 1966 to the present. In addition, improvements in data reduction techniques have resulted in a set of Mercury ranging data less affected by systematic error, in particular the biases introduced by local topographic variations. We use this new set of reduced ranging data to improve Mercury's global topography and center-of-figure minus center-of-mass offset. New results on crustal thickness are derived, and prospects for further improvement with Mercury Orbiter data are discussed.

  19. Mercury's Seasonal Sodium Exosphere: MESSENGER Orbital Observations

    Science.gov (United States)

    Cassidy, Timothy A.; Merkel, Aimee W.; Burger, Matthew H.; Killen, Rosemary M.; McClintock, William E.; Vervack, Ronald J., Jr.; Sarantos, Menelaos

    2014-01-01

    The Mercury Atmospheric and Surface Composition Spectrometer (MASCS) Ultraviolet and Visible Spectrometer (UVVS) on the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft now orbiting Mercury provides the first close-up look at the planet's sodium exosphere. UVVS has observed the exosphere from orbit almost daily for over 10 Mercury years. In this paper we describe and analyze a subset of these data: altitude profiles taken above the low-latitude dayside and south pole. The observations show spatial and temporal variations, but there are no obvious year-to-year variations in most of the observations. We do not see the episodic variability reported by some ground-based observers. We used these altitude profiles to make estimates of sodium density and temperature. The bulk of the exosphere, at about 1200 K, is much warmer than Mercury's surface. This value is consistent with some ground-based measurements and suggests that photon-stimulated desorption is the primary ejection process. We also observe a tenuous energetic component but do not see evidence of the predicted thermalized (or partially thermalized) sodium near Mercury's surface temperature. Overall we do not see the variable mixture of temperatures predicted by most Monte Carlo models of the exosphere.

  20. Mercury Retention by Fly Ashes from Oxy-fuel Processes

    OpenAIRE

    Fernández Miranda, Nuria; Villamil Rumayor, Marta; López Antón, María Antonia; Díaz Somoano, Mercedes; Martínez Tarazona, María Rosa

    2015-01-01

    The objective of this study is to determine the mechanism of mercury retention in fly ashes, the main solid waste from coal combustion power plants, and to evaluate the interactions between the type of mercury and fly ashes. The work was based on the results of mercury speciation in the gas and the solid fly ash before and after mercury retention. The identification of the mercury species in the gas was performed using previously validated methods, but the speciation of the mercury retained i...

  1. NMR of mercury in porous coal and silica gel

    International Nuclear Information System (INIS)

    Kasperovich, V.S.; Charnaya, E.V.; Tien, C.; Wur, C.S.

    2003-01-01

    Temperature dependences of the integral intensity and NMR signals Knight shift in 199 Hg nuclei are measured for liquid and solid mercury introduced into the porous coal and silica gel. The decrease in the crystallization completion temperature and small temperature hysteresis (from 4 up to 9 K) between melting and crystallization are identified. Mercury melting temperature in pores coincided with melting temperature of the bulk mercury. NMR signal from crystalline mercury under conditions of limited geometry was observed for the first time. It is ascertained that Knight shift for mercury in the pores both in liquid and crystalline phases is lesser than for the bulk mercury [ru

  2. 40 CFR 421.200 - Applicability: Description of the secondary mercury subcategory.

    Science.gov (United States)

    2010-07-01

    ... secondary mercury subcategory. 421.200 Section 421.200 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Secondary Mercury Subcategory § 421.200 Applicability: Description of the secondary mercury... mercury from secondary mercury facilities processing recycled mercuric oxide batteries and other mercury...

  3. Mercury recycling in the United States in 2000

    Science.gov (United States)

    Brooks, William E.; Matos, Grecia R.

    2005-01-01

    Reclamation and recycling of mercury from used mercury- containing products and treatment of byproduct mercury from gold mining is vital to the continued, though declining, use of this metal. Mercury is reclaimed from mercury-containing waste by treatment in multistep high-temperature retorts-the mercury is volatized and then condensed for purification and sale. Some mercury-containing waste, however, may be landfilled, and landfilled material represents loss of a recyclable resource and a threat to the environment. Related issues include mercury disposal and waste management, toxicity and human health, and regulation of mercury releases in the environment. End-users of mercury-containing products may face fines and prosecution if these products are improperly recycled or not recycled. Local and State environmental regulations require adherence to the Resource Conservation and Recovery Act and the Comprehensive Environmental Response, Compensation, and Liability Act to regulate generation, treatment, and disposal of mercury-containing products. In the United States, several large companies and a number of smaller companies collect these products from a variety of sources and then reclaim and recycle the mercury. Because mercury has not been mined as a principal product in the United States since 1992, mercury reclamation from fabricated products has become the main source of mercury. Principal product mercury and byproduct mercury from mining operations are considered to be primary materials. Mercury may also be obtained as a byproduct from domestic or foreign gold-processing operations. In the early 1990s, U.S. manufacturers used an annual average that ranged from 500 to 600 metric tons of recycled and imported mercury for fabrication of automobile convenience switches, dental amalgam, fluorescent lamps, medical uses and thermometers, and thermostats. The amount now used for fabrication is estimated to be 200 metric tons per year or less. Much of the data on

  4. Mercury Exposure: Protein Biomarkers of Mercury Exposure in Jaraqui Fish from the Amazon Region.

    Science.gov (United States)

    Vieira, José Cavalcante Souza; Braga, Camila Pereira; de Oliveira, Grasieli; Padilha, Cilene do Carmo Federici; de Moraes, Paula Martin; Zara, Luiz Fabricio; Leite, Aline de Lima; Buzalaf, Marília Afonso Rabelo; Padilha, Pedro de Magalhães

    2018-05-01

    This study presents data on the extraction and characterization of proteins associated with mercury in the muscle and liver tissues of jaraqui (Semaprochilodus spp.) from the Madeira River in the Brazilian Amazon. Protein fractionation was carried out by two-dimensional electrophoresis (2D-PAGE). Mercury determination in tissues, pellets, and protein spots was performed by graphite furnace atomic absorption spectrometry (GFAAS). Proteins in the spots that showed mercury were characterized by electrospray ionization tandem mass spectrometry (ESI-MS/MS). The highest mercury concentrations were found in liver tissues and pellets (426 ± 6 and 277 ± 4 μg kg -1 ), followed by muscle tissues and pellets (132 ± 4 and 86 ± 1 μg kg -1 , respectively). Mercury quantification in the protein spots allowed us to propose stoichiometric ratios in the range of 1-4 mercury atoms per molecule of protein in the protein spots. The proteins characterized in the analysis by ESI-MS/MS were keratin, type II cytoskeletal 8, parvalbumin beta, parvalbumin-2, ubiquitin-40S ribosomal S27a, 39S ribosomal protein L36 mitochondrial, hemoglobin subunit beta, and hemoglobin subunit beta-A/B. The results suggest that proteins such as ubiquitin-40S ribosomal protein S27a, which have specific domains, possibly zinc finger, can be used as biomarkers of mercury, whereas mercury and zinc present characteristics of soft acids.

  5. Formation of Soluble Mercury Oxide Coatings: Transformation of Elemental Mercury in Soils.

    Science.gov (United States)

    Miller, Carrie L; Watson, David B; Lester, Brian P; Howe, Jane Y; Phillips, Debra H; He, Feng; Liang, Liyuan; Pierce, Eric M

    2015-10-20

    The impact of mercury (Hg) on human and ecological health has been known for decades. Although a treaty signed in 2013 by 147 nations regulates future large-scale mercury emissions, legacy Hg contamination exists worldwide and small-scale releases will continue. The fate of elemental mercury, Hg(0), lost to the subsurface and its potential chemical transformation that can lead to changes in speciation and mobility are poorly understood. Here, we show that Hg(0) beads interact with soil or manganese oxide solids and X-ray spectroscopic analysis indicates that the soluble mercury coatings are HgO. Dissolution studies show that, after reacting with a composite soil, >20 times more Hg is released into water from the coated beads than from a pure liquid mercury bead. An even larger, >700 times, release occurs from coated Hg(0) beads that have been reacted with manganese oxide, suggesting that manganese oxides are involved in the transformation of the Hg(0) beads and creation of the soluble mercury coatings. Although the coatings may inhibit Hg(0) evaporation, the high solubility of the coatings can enhance Hg(II) migration away from the Hg(0)-spill site and result in potential changes in mercury speciation in the soil and increased mercury mobility.

  6. OCCURRENCE OF MICROORGANISMS RESISTANT TO MERCURY IN MERCURY CONTAMINATED SOILS AND SEDIMENTS IN PAVLODAR, KAZAKHSTAN

    Science.gov (United States)

    There is extensive mercury contamination of soil surrounding a chloralkali plant in Pavlodar, Kazakhstan that operated from 1970 to 1990. High-level mercury contamination exists within the confines of the plant, at nearby off-site waste storage and evaporation ponds, and in Balky...

  7. OCCURRENCE OF MERCURY-RESISTANT MICROORGANISMS IN MERCURY-CONTAMINATED SOILS AND SEDIMENTS IN PAVLODAR, KAZAKHSTAN

    Science.gov (United States)

    There is extensive mercury contamination of soil surrounding a chloralkali plant in Pavlodar, Kazakhstan that operated from 1970 to 1990. High-level mercury contamination exists within the confines of the plant, at nearby off-site waste storage and evaporation ponds, and in Balky...

  8. Bacterial Mercury Methylation At The Sediment-Water Interface Of Mercury Contaminated Sediments

    Science.gov (United States)

    Bench scale experiments were conducted to improve our understanding of bacterial mediation of mercury transformation (methylation), specifically those factors which govern the production of methyl mercury (MeHg) at the sediment-water interface. The greatest cause for concern re...

  9. ANALYSIS OF MERCURY IN VERMONT AND NEW HAMPSHIRE LAKES: EVALUATION OF THE REGIONAL MERCURY CYCLING MODEL

    Science.gov (United States)

    An evaluation of the Regional Mercury Cycling Model (R-MCM, a steady-state fate and transport model used to simulate mercury concentrations in lakes) is presented based on its application to a series of 91 lakes in Vermont and New Hampshire. Visual and statistical analyses are pr...

  10. Aerobic Mercury-resistant bacteria alter Mercury speciation and retention in the Tagus Estuary (Portugal).

    Science.gov (United States)

    Figueiredo, Neusa L; Canário, João; O'Driscoll, Nelson J; Duarte, Aida; Carvalho, Cristina

    2016-02-01

    Aerobic mercury-resistant bacteria were isolated from the sediments of two highly mercury-polluted areas of the Tagus Estuary (Barreiro and Cala do Norte) and one natural reserve area (Alcochete) in order to test their capacity to transform mercury. Bacterial species were identified using 16S rRNA amplification and sequencing techniques and the results indicate the prevalence of Bacillus sp. Resistance patterns to mercurial compounds were established by the determination of minimal inhibitory concentrations. Representative Hg-resistant bacteria were further tested for transformation pathways (reduction, volatilization and methylation) in cultures containing mercury chloride. Bacterial Hg-methylation was carried out by Vibrio fluvialis, Bacillus megaterium and Serratia marcescens that transformed 2-8% of total mercury into methylmercury in 48h. In addition, most of the HgR bacterial isolates showed Hg(2+)-reduction andHg(0)-volatilization resulting 6-50% mercury loss from the culture media. In summary, the results obtained under controlled laboratory conditions indicate that aerobic Hg-resistant bacteria from the Tagus Estuary significantly affect both the methylation and reduction of mercury and may have a dual face by providing a pathway for pollution dispersion while forming methylmercury, which is highly toxic for living organisms. Copyright © 2015 Elsevier Inc. All rights reserved.

  11. Behavior of mercury in biosystems. III. Biotransference of mercury through food chains

    Energy Technology Data Exchange (ETDEWEB)

    Hamdy, M.K.; Prabhu, N.V.

    1979-01-01

    This study was conducted to follow the biotransference of radioactive mercury in a simple model food chain which consisted of four trophic levels: from mercury resistant bacteria to mosquito larvae; then from larvae to guppies (small fish); and finally from guppies to Cichlids (big fish). Factors affecting this biotransference in the various trophic levels were also examined.

  12. Examining the interrelationship between DOC, bromide and chlorine dose on DBP formation in drinking water--a case study.

    Science.gov (United States)

    Bond, Tom; Huang, Jin; Graham, Nigel J D; Templeton, Michael R

    2014-02-01

    During drinking water treatment aqueous chlorine and bromine compete to react with natural organic matter (NOM). Among the products of these reactions are potentially harmful halogenated disinfection by-products, notably four trihalomethanes (THM4) and nine haloacetic acids (HAAs). Previous research has concentrated on the role of bromide in chlorination reactions under conditions of a given NOM type and/or concentration. In this study different concentrations of dissolved organic carbon (DOC) from U.K. lowland water were reacted with varying amounts of bromide and chlorine in order to examine the interrelationship between the three reactants in the formation of THM4, dihaloacetic acids (DHAAs) and trihaloacetic acids (THAAs). Results showed that, in general, molar yields of THM4 increased with DOC, bromide and chlorine concentrations, although yields did fluctuate versus chlorine dose. In contrast both DHAA and THAA yields were mainly independent of changes in bromide and chlorine dose at low DOC (1 mg·L(-1)), but increased with chlorine dose at higher DOC concentrations (4 mg·L(-1)). Bromine substitution factors reached maxima of 0.80, 0.67 and 0.65 for the THM4, DHAAs and THAAs, respectively, at the highest bromide/chlorine ratio studied. These results suggest that THM4 formation kinetics depend on both oxidation and halogenation steps, whereas for DHAAs and THAAs oxidation steps are more important. Furthermore, they indicate that high bromide waters may prove more problematic for water utilities with respect to THM4 formation than for THAAs or DHAAs. While mass concentrations of all three groups increased in response to increased bromide incorporation, only the THMs also showed an increase in molar yield. Overall, the formation behaviour of DHAA and THAA was more similar than that of THM4 and THAA. © 2013.

  13. Removal of bromide from aqueous solutions using the UV/ZnO process based on the multivariate analysis model

    Directory of Open Access Journals (Sweden)

    Kolsoom Mohammad Moradi

    2017-02-01

    Full Text Available Background: Bromide is found naturally in groundwater and surface water. The rapid growth of industrial activities, drainage of surface runoff, and use of methyl bromide in pesticides has increased bromide discharge to the environment. Disinfection of water-containing bromide causes the creation of additional products of organo-halogenated that are considered cancer-causing agents. In this study, the effect and optimization of factors in removal of this ion was evaluated by using the nano-photocatalytic UV/ZnO process. Methods: This analytical study was conducted in a batch system by the phenol-red method. The test design was performed through the analysis model of multi-factor variance with 99 subjects, while the main, interactive, and reciprocal effects of variables, such as reaction time, catalyst concentration, bromide concentration, and pH at different levels of each factor, were analysed by using SPSS version 16. Results: The main, interactive, and reciprocal effects of factors were significant in three different levels with P < 0.001, and the optimal level of the factors reaction time, catalyst concentration, bromide concentration, and pH were 120 minutes, 0.5, 0.1, and 7 mg/L, respectively, by using the Schaffer test. The highest removal efficiency of 95% was obtained at least 91.56 and a maximum of 94.76% was obtained under optimal conditions of all factors. Conclusion: The results show that by optimization of factors, this process can be effectively used to remove bromide from aquatic environments.

  14. Visualization and Studies of Ion-Diffusion Kinetics in Cesium Lead Bromide Perovskite Nanowires.

    Science.gov (United States)

    Pan, Dongxu; Fu, Yongping; Chen, Jie; Czech, Kyle J; Wright, John C; Jin, Song

    2018-03-14

    The facile chemical transformation of metal halide perovskites via ion exchange has been attributed to their "soft" crystal lattices that enable fast ion migration. Kinetic studies of such processes could provide mechanistic insights on the ion migration dynamics. Herein, by using aligned single-crystal nanowires of cesium lead bromide (CsPbBr 3 ) perovskite on epitaxial substrates as platforms, we visualize and investigate the cation or anion interdiffusion kinetics via spatially resolved photoluminescence measurement on heterostructures fabricated by stacking CsPbCl 3 , MAPbI 3 , or MAPbBr 3 microplates on top of CsPbBr 3 nanowires. Time-dependent confocal photoluminescence microscopy and energy-dispersive X-ray spectroscopy showed the solid-state anion interdiffusion readily occurs to result in halide concentration gradients along CsPbBr 3-3 x Cl 3 x ( x = 0-1) nanowires. Quantitative analysis of such composition profiles using Fick's law allowed us, for the first time, to extract interdiffusion coefficients of the chloride-bromide couple and an activation energy of 0.44 ± 0.02 eV for ion diffusion from temperature-dependent studies. In contrast, iodide-bromide interdiffusion is limited, likely due to the complex phase behaviors of mixed alloys of CsPb(Br,I) 3 . In contrast to the relatively mobile anions, A-site cation interdiffusion across the MAPbBr 3 /CsPbBr 3 junctions was barely observed at room temperature. Our results present a general method to investigate the kinetics of the solid-state ion migration, and the gained insights on ion diffusion can provide guidelines for rationally designing perovskite heterostructures that could lead to new properties for fundamental studies and technological applications.

  15. Mercury risk in poultry in the Wanshan Mercury Mine, China.

    Science.gov (United States)

    Yin, Runsheng; Zhang, Wei; Sun, Guangyi; Feng, Zhaohui; Hurley, James P; Yang, Liyuan; Shang, Lihai; Feng, Xinbin

    2017-11-01

    In this study, total mercury (THg) and methylmercury (MeHg) concentrations in muscles (leg and breast), organs (intestine, heart, stomach, liver) and blood were investigated for backyard chickens, ducks and geese of the Wanshan Mercury Mine, China. THg in poultry meat products range from 7.9 to 3917.1 ng/g, most of which exceeded the Chinese national standard limit for THg in meat (50 ng/g). Elevated MeHg concentrations (0.4-62.8 ng/g) were also observed in meat products, suggesting that poultry meat can be an important human MeHg exposure source. Ducks and geese showed higher Hg levels than chickens. For all poultry species, the highest Hg concentrations were observed in liver (THg: 23.2-3917.1 ng/g; MeHg: 7.1-62.8 ng/g) and blood (THg: 12.3-338.0 ng/g; MeHg: 1.4-17.6 ng/g). We estimated the Hg burdens in chickens (THg: 15.3-238.1 μg; MeHg: 2.2-15.6 μg), ducks (THg: 15.3-238.1 μg; MeHg: 3.5-14.7 μg) and geese (THg: 83.8-93.4 μg; MeHg: 15.4-29.7 μg). To not exceed the daily intake limit for THg (34.2 μg/day) and MeHg (6 μg/day), we suggested that the maximum amount (g) for chicken leg, breast, heart, stomach, intestine, liver, and blood should be 1384, 1498, 2315, 1214, 1081, 257, and 717, respectively; the maximum amount (g) for duck leg, breast, heart, stomach, intestine, liver, and blood should be 750, 1041, 986, 858, 752, 134, and 573, respectively; and the maximum amount (g) for goose leg, breast, heart, stomach, intestine, liver, and blood should be 941, 1051, 1040, 1131, 964, 137, and 562, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Efficient SN2 fluorination of primary and secondary alkyl bromides by copper(I) fluoride complexes

    KAUST Repository

    Liu, Yanpin

    2013-11-11

    Copper(I) fluoride complexes ligated by phenanthroline derivatives have been synthesized and structurally characterized by X-ray crystallography. These complexes adopt as either ionic or neutral forms in the solid state, depending on the steric bulkiness of the substituent groups on the phenanthroline ligands. These complexes react with primary and secondary alkyl bromides to produce the corresponding alkyl fluorides in modest to good yields. This new method is compatible with a variety of important functional groups such as ether, thioether, amide, nitrile, methoxyl, hydroxyl, ketone, ester, and heterocycle moieties. © 2013 American Chemical Society.

  17. A menu-driven program for determining properties of aqueous lithium bromide solutions

    Energy Technology Data Exchange (ETDEWEB)

    Patterson, M.R.; Crosswhite, R.N.; Perez-Blanco, H.

    1990-01-01

    This report contains a description of the computer program LIMENU for calculating the thermodynamic and transport properties of aqueous solutions of lithium bromide. A user's guide is included, together with a description of how the program produces displays and plots on the screen. The routines that calculate the properties are also described briefly. It is hoped that a program of this nature, with plotting capabilities and up-to-date information, will be useful to engineers and to researchers in the area of absorption. 4 refs., 3 figs.

  18. Emission characteristics of plasma based on xenon-rubidium bromide mixture

    Science.gov (United States)

    Heneral, A. A.; Avtaeva, S. V.

    2017-10-01

    Luminescence spectra of a longitudinal pulse-periodic discharge in xenon mixture with rubidium bromide vapors (Xe-RbBr) are studied experimentally at low pressures. The conditions leading to the appearance of intense bands of ultraviolet radiation of exciplex XeBr* molecules in the spectral interval between 200 and 400 nm are found. The highest yield of UV radiation of XeBr* molecules is achieved when the temperature of discharge-tube walls is equal to 750°C. A maximum power of UV radiation from the entire plasma volume as high as 4.8 W is obtained.

  19. Use of Cyclic Allylic Bromides in the Zinc–Mediated Aqueous Barbier–Grignard Reaction

    OpenAIRE

    Breton, Gary W.; Shugart, John H.; Hughey, Christine A.; Conrad, Brian P.; Perala, Suzanne M.

    2001-01-01

    The zinc–mediated aqueous Barbier–Grignard reaction of cyclic allylic bromide substrates with various aldehydes and ketones to afford homoallylic alcohols was investigated. Aromatic aldehydes and ketones afforded adducts in good yields (66–90%) and with good diastereoselectivities. Non–aromatic aldehydes also reacted well under these conditions, but only poor yields were obtained with non–aromatic ketones. Regioselectivity was high when some substituted cyclic allylic...

  20. Research on Wheat Straw Pulping with Ionic Liquid 1-Ethyl-3-Methylimidazole Bromide

    Directory of Open Access Journals (Sweden)

    Wei Song

    2016-12-01

    Full Text Available In this paper, the pulping process of wheat straw using ionic liquid 1-ethyl-3-methylimidazolium bromide ([Emim]Br as the digestion liquor is presented. The influence of pulping conditions on the pulp yield are analysed by single-factor and orthogonal experiments, and optimum pulping conditions are obtained. The average pulp yield reaches 44 %, and the average recovery rate of ionic liquid is 93.5 %. The XRD pattern shows no obvious change in the crystal structure of the wheat straw cellulose. Additionally, the SEM image illustrates that there are many fine fibres in the pulp and the spaces between the fibres are large.

  1. In situ measurement of methyl bromide in indoor air using long-path FTIR spectroscopy

    Science.gov (United States)

    Green, Martina; Seiber, James N.; Biermann, Heinz W.

    1991-05-01

    A new Fourier transform infrared (FTIR) spectrometer has been set up at the California Department of Flood and Agriculture for monitoring gas phase pesticides and inert ingredients used in the formulation of pesticides. To allow detection of trace quantities down to the ppm range, the FTIR instrument has been interfaced to a custom, external open multiple reflection system with a base pathlength of 2.5 m. The mirror system is of the double corner cube White type design capable of achieving a total absorption pathlength of 140 m. Our initial application was to monitor the concentration of methyl bromide after controlled releases of this fumigant into an indoor environment.

  2. Digitization of Bromide Paper Records to Extract One-Minute Geomagnetic Data

    Directory of Open Access Journals (Sweden)

    N Mashiko

    2013-05-01

    Full Text Available Many long-term geomagnetic observation results recorded on photographic bromide paper have not yet been fully digitized. To that end, we developed a method to automatically convert photographic records to one-minute digital data. We applied our method to the observation records of Kakioka Magnetic Observatory and confirmed that the resolution of time and amplitude could be greatly improved by numerical conversion compared with conventional data conversion by hand scaling. Our results suggest that highly precise digitization of analog magnetograms is possible.

  3. Biomarkers of mercury exposure at a mercury recycling facility in Ukraine

    Science.gov (United States)

    Gibb, H.J.; Kozlov, K.; Buckley, J.P.; Centeno, J.; Jurgenson, V.; Kolker, A.; Conko, K.; Landa, E.; Panov, B.; Panov, Y.; Xu, H.

    2008-01-01

    This study evaluates biomarkers of occupational mercury exposure among workers at a mercury recycling operation in Gorlovka, Ukraine. The 29 study participants were divided into three occupational categories for analysis: (1) those who worked in the mercury recycling operation (Group A, n = 8), (2) those who worked at the facility but not in the yard where the recycling was done (Group B, n = 14), and (3) those who did not work at the facility (Group C, n = 7). Urine, blood, hair, and nail samples were collected from the participants, and a questionnaire was administered to obtain data on age, gender, occupational history, smoking, alcohol consumption, fish consumption, tattoos, dental amalgams, home heating system, education, source of drinking water, and family employment in the former mercury mine/smelter located on the site of the recycling facility. Each factor was tested in a univariate regression with total mercury in urine, blood, hair, and nails. Median biomarker concentrations were 4.04 ??g/g-Cr (urine), 2.58 ??g/L (blood), 3.95 ??g/g (hair), and 1.16 ??g/g (nails). Occupational category was significantly correlated (p < 0.001) with both blood and urinary mercury concentrations but not with hair or nail mercury. Four individuals had urinary mercury concentrations in a range previously found to be associated with subtle neurological and subjective symptoms (e.g., fatigue, loss of appetite, irritability), and one worker had a urinary mercury concentration in a range associated with a high probability of neurological effects and proteinuria. Comparison of results by occupational category found that workers directly involved with the recycling operation had the highest blood and urinary mercury levels. Those who worked at the facility but were not directly involved with the recycling operation had higher levels than those who did not work at the facility. Copyright ?? 2008 JOEH, LLC.

  4. MESSENGER at Mercury: Early Orbital Operations

    Science.gov (United States)

    McNutt, Ralph L., Jr; Solomon, Sean C.; Bedini, Peter D.; Anderson, Brian J.; Blewett, David T.; Evans, Larry G.; Gold, Robert E.; Krimigis, Stamatios M.; Murchie, Scott L.; Nittler, Larry R.; hide

    2013-01-01

    The MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft, launched in August 2004 under NASA's Discovery Program, was inserted into orbit about the planet Mercury in March 2011. MESSENGER's three flybys of Mercury in 2008-2009 marked the first spacecraft visits to the innermost planet since the Mariner 10 flybys in 1974-1975. The unprecedented orbital operations are yielding new insights into the nature and evolution of Mercury. The scientific questions that frame the MESSENGER mission led to the mission measurement objectives to be achieved by the seven payload instruments and the radio science experiment. Interweaving the full set of required orbital observations in a manner that maximizes the opportunity to satisfy all mission objectives and yet meet stringent spacecraft pointing and thermal constraints was a complex optimization problem that was solved with a software tool that simulates science observations and tracks progress toward meeting each objective. The final orbital observation plan, the outcome of that optimization process, meets all mission objectives. MESSENGER's Mercury Dual Imaging System is acquiring a global monochromatic image mosaic at better than 90% coverage and at least 250 m average resolution, a global color image mosaic at better than 90% coverage and at least 1 km average resolution, and global stereo imaging at better than 80% coverage and at least 250 m average resolution. Higher-resolution images are also being acquired of targeted areas. The elemental remote sensing instruments, including the Gamma-Ray and Neutron Spectrometer and the X-Ray Spectrometer, are being operated nearly continuously and will establish the average surface abundances of most major elements. The Visible and Infrared Spectrograph channel of MESSENGER's Mercury Atmospheric and Surface Composition Spectrometer is acquiring a global map of spectral reflectance from 300 to 1450 nm wavelength at a range of incidence and emission

  5. Making Mercury's Core with Light Elements

    Science.gov (United States)

    Vander Kaaden, Kathleen E.; McCubbin, Francis M.; Ross, D. Kent

    2016-01-01

    Recent results obtained from the MErcury Surface, Space ENvironment, GEochemistry, and Ranging spacecraft showed the surface of Mercury has low FeO abundances (less than 2 wt%) and high S abundances (approximately 4 wt%), suggesting the oxygen fugacity of Mercury's surface materials is somewhere between 3 to 7 log10 units below the IW buffer. The highly reducing nature of Mercury has resulted in a relatively thin mantle and a large core that has the potential to exhibit an exotic composition in comparison to the other terrestrial planets. This exotic composition may extend to include light elements (e.g., Si, C, S). Furthermore, has argued for a possible primary floatation crust on Mercury composed of graphite, which may require a core that is C-saturated. In order to investigate mercurian core compositions, we conducted piston cylinder experiments at 1 GPa, from 1300 C to 1700 C, using a range of starting compositions consisting of various Si-Fe metal mixtures (Si5Fe95, Si10Fe90, Si22Fe78, and Si35Fe65). All metals were loaded into graphite capsules used to ensure C-saturation during the duration of each experimental run. Our experiments show that Fe-Si metallic alloys exclude carbon relative to more Fe-rich metal. This exclusion of carbon commences within the range of 5 to 10 wt% Si. These results indicate that if Mercury has a Si-rich core (having more than approximately 5 wt% silicon), it would have saturated in carbon at low C abundances allowing for the possible formation of a graphite floatation crust as suggested by. These results have important implications for the thermal and magmatic evolution of Mercury.

  6. Mercury Exposure among Garbage Workers in Southern Thailand

    Directory of Open Access Journals (Sweden)

    Somsiri Decharat

    2012-12-01

    Conclusion: Changing garbage workers’ hygiene habits can reduce urinary mercury levels. Personal hygiene is important, and should be stressed in education programs. Employers should institute engineering controls to reduce urinary mercury levels among garbage workers.

  7. Distribution of atmospheric mercury species near ground. [Tampa Bay, Florida

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, D.L.; Braman, R.S.

    1974-01-01

    A recently developed technique makes possible the routine analysis of atmospheric samples for particulate and volatile mercury. The volatile fraction can be analyzed for several chemical species. This work presents the results of some Tampb Bay area analyses and diurnal studies of atmospheric mercury speciation. The mercury in air in the area investigated was primarily volatile (>90%) and was composed of significant proportions of mercury (II)-type compounds, methylmercury (II)-type compounds, and elemental mercury. Dimethylmercury was rarely observed. Results were quite variable suggesting a variety of sources and irregular wind transport processes. The data indicate that background mercury concentrations and the percentage distribution of mercury species in air in a local area may be established by mercury emanations from the ground or from adjacent bodies of water.

  8. Mercury chloride-induced oxidative stress in human erythrocytes ...

    African Journals Online (AJOL)

    ONOS

    2010-01-25

    ). Intake of metallic mercury vapour amounts to 3, 9 - 21 µg /day ..... Comparative in vitro cytogenetic studies in mercury-exposed human lymphocytes. Mutat. Res. 157: 221-226. Verschaeve L, Kirsch-Volders M, Susanne C ...

  9. Reducing global mercury emissions in artisanal and small-scale ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2016-04-28

    caused mercury emissions, surpassing even coal-burning. With more than 15 million small-scale gold miners operating in more than 70 countries today, finding a way to reduce mercury emissions is vital.

  10. Removal of mercury from coal via a microbial pretreatment process

    Science.gov (United States)

    Borole, Abhijeet P [Knoxville, TN; Hamilton, Choo Y [Knoxville, TN

    2011-08-16

    A process for the removal of mercury from coal prior to combustion is disclosed. The process is based on use of microorganisms to oxidize iron, sulfur and other species binding mercury within the coal, followed by volatilization of mercury by the microorganisms. The microorganisms are from a class of iron and/or sulfur oxidizing bacteria. The process involves contacting coal with the bacteria in a batch or continuous manner. The mercury is first solubilized from the coal, followed by microbial reduction to elemental mercury, which is stripped off by sparging gas and captured by a mercury recovery unit, giving mercury-free coal. The mercury can be recovered in pure form from the sorbents via additional processing.

  11. What are the Connections between Mercury and CFLs?

    Science.gov (United States)

    Small amounts of mercury vapor can be released when CFLs break or are improperly disposed of. Despite these emissions, the use of CFLs actually helps reduce total mercury emissions in the U.S. because of their significant energy savings.

  12. Bioremediation of toxic substances by mercury resistant marine bacteria

    Digital Repository Service at National Institute of Oceanography (India)

    De, J.; Sarkar, A.; Ramaiah, N.

    Bioremediation of toxic substances includes microbe-mediated enzymatic transformation of toxicants to non-toxic, often assimilable, forms. Mercury-resistant marine bacteria are found to be very promising in dealing with mercury, and a host of other...

  13. Bromide Sources and Loads in Swiss Surface Waters and Their Relevance for Bromate Formation during Wastewater Ozonation.

    Science.gov (United States)

    Soltermann, Fabian; Abegglen, Christian; Götz, Christian; von Gunten, Urs

    2016-09-20

    Bromide measurements and mass balances in the catchments of major Swiss rivers revealed that chemical industry and municipal waste incinerators are the most important bromide sources and account for ∼50% and ∼20%, respectively, of the ∼2000 tons of bromide discharged in the Rhine river in 2014 in Switzerland. About 100 wastewater treatment plants (WWTPs) will upgrade their treatment for micropollutant abatement in the future to comply with Swiss regulations. An upgrade with ozonation may lead to unintended bromate formation in bromide-containing wastewaters. Measured bromide concentrations were industry). Wastewater ozonation formed little bromate at specific ozone doses of ≤0.4 mg O3/mg DOC, while the bromate yields were almost linearly correlated to the specific ozone dose for higher ozone doses. Molar bromate yields for typical specific ozone doses in wastewater treatment (0.4-0.6 mg O3/mg DOC) are ≤3%. In a modeled extreme scenario (in which all upgraded WWTPs release 10 μg L(-1) of bromate), bromate concentrations increased by major Swiss rivers and by several micrograms per liter in receiving water bodies with a high fraction of municipal wastewater.

  14. Below a Historic Mercury Mine: Non-linear Patterns of Mercury Bioaccumulation in Aquatic Organisms

    Science.gov (United States)

    Haas, J.; Ichikawa, G.; Ode, P.; Salsbery, D.; Abel, J.

    2001-12-01

    Unlike most heavy metals, mercury is capable of bioaccumulating in aquatic food-chains, primarily because it is methylated by bacteria in sediment to the more toxic methylmercury form. Mercury concentrations in a number of riparian systems in California are highly elevated as a result of historic mining activities. These activities included both the mining of cinnabar in the coastal ranges to recover elemental mercury and the use of elemental mercury in the gold fields of the Sierra Nevada Mountains. The most productive mercury mining area was the New Almaden District, now a county park, located in the Guadalupe River drainage of Santa Clara County, where cinnabar was mined and retorted for over 100 years. As a consequence, riparian systems in several subwatersheds of the Guadalupe River drainage are contaminated with total mercury concentrations that exceed state hazardous waste criteria. Mercury concentrations in fish tissue frequently exceed human health guidelines. However, the potential ecological effects of these elevated mercury concentrations have not been thoroughly evaluated. One difficulty is in extrapolating sediment concentrations to fish tissue concentrations without accounting for physical and biological processes that determine bioaccumulation patterns. Many processes, such as methylation and demethylation of mercury by bacteria, assimilation efficiency in invertebrates, and metabolic rates in fish, are nonlinear, a factor that often confounds attempts to evaluate the effects of mercury contamination on aquatic food webs. Sediment, benthic macroinvertebrate, and fish tissue samples were collected in 1998 from the Guadalupe River drainage in Santa Clara County at 13 sites upstream and downstream from the historic mining district. Sediment and macroinvertebrate samples were analyzed for total mercury and methylmercury. Fish samples were analyzed for total mercury as whole bodies, composited by species and size. While linear correlations of sediment

  15. Mercury Toxicity and Treatment: A Review of the Literature

    Directory of Open Access Journals (Sweden)

    Robin A. Bernhoft

    2012-01-01

    Full Text Available Mercury is a toxic heavy metal which is widely dispersed in nature. Most human exposure results from fish consumption or dental amalgam. Mercury occurs in several chemical forms, with complex pharmacokinetics. Mercury is capable of inducing a wide range of clinical presentations. Diagnosis of mercury toxicity can be challenging but can be obtained with reasonable reliability. Effective therapies for clinical toxicity have been described.

  16. Mercury Toxicity and Treatment: A Review of the Literature

    Science.gov (United States)

    Bernhoft, Robin A.

    2012-01-01

    Mercury is a toxic heavy metal which is widely dispersed in nature. Most human exposure results from fish consumption or dental amalgam. Mercury occurs in several chemical forms, with complex pharmacokinetics. Mercury is capable of inducing a wide range of clinical presentations. Diagnosis of mercury toxicity can be challenging but can be obtained with reasonable reliability. Effective therapies for clinical toxicity have been described. PMID:22235210

  17. Mercury species in formerly contaminated soils and released soil gases

    Czech Academy of Sciences Publication Activity Database

    Sysalová, J.; Kučera, Jan; Drtinová, B.; Červenka, R.; Zvěřina, O.; Komárek, J.; Kameník, Jan

    2017-01-01

    Roč. 584, APR (2017), s. 1032-1039 ISSN 0048-9697 R&D Projects: GA ČR(CZ) GBP108/12/G108; GA MŠk LM2015056 Institutional support: RVO:61389005 Keywords : mercury contaminated soils * total mercury * elemental mercury * methylmercury * phynelmercury * gaseous elemental mercury Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 4.900, year: 2016

  18. 2,2′-Bipyridin-1′-ium 1-oxide bromide monohydrate

    Directory of Open Access Journals (Sweden)

    Katharina Heintz

    2018-03-01

    Full Text Available The title compound 2,2′-bipyridin-1′-ium 1-oxide bromide crystallizes as a monohydrate, C10H9N2+·Br−·H2O. Structural disorder is observed due to the fact that protonation, as well as oxidation, of the N atoms of 2,2′-bipyridine occurs at either of the N atoms. The disorder extends to the remainder of the cation, with a refined occupancy rate of 0.717 (4 for the major moiety. An intramolecular N—H...O hydrogen bond forces the bipyridine unit into an s-cis conformation. Each pair of neighbouring 2,2′-bipyridin-1′-ium ions forms a dimeric aggregate by hydrogen bonds between their respective N—O and the N—H functions. These dimers and hydrogen-bonding interactions with bromide ions and the water molecule give rise to a complex supramolecular arrangement.

  19. Study of the Reaction 2-(p-Nitrophenylethyl Bromide + OH− in Dimeric Micellar Solutions

    Directory of Open Access Journals (Sweden)

    María Luisa Moyá

    2011-11-01

    Full Text Available The dehydrobromination reaction 2-(p-nitrophenylethyl bromide + OH− was investigated in several alkanediyl-a-w-bis(dodecyldimethylammonium bromide, 12-s-12,2Br− (with s = 2, 3, 4, 5, 6, 8, 10, 12 micellar solutions, in the presence of NaOH 5 × 10−3 M. The kinetic data were quantitatively rationalized within the whole surfactant concentration range by using an equation based on the pseudophase ion-exchange model and taking the variations in the micellar ionization degree caused by the morphological transitions into account. The agreement between the theoretical and the experimental data was good in all the dimeric micellar media studied, except for the 12-2-12,2Br− micellar solutions. In this case, the strong tendency to micellar growth shown by the 12-2-12,2Br− micelles could be responsible for the lack of accordance. Results showed that the dimeric micelles accelerate the reaction more than two orders of magnitude as compared to water.

  20. Surface Electronic Structure of Hybrid Organo Lead Bromide Perovskite Single Crystals

    KAUST Repository

    Komesu, Takashi

    2016-08-24

    The electronic structure and band dispersion of methylammonium lead bromide, CH3NH3PbBr3, has been investigated through a combination of angle-resolved photoemission spectroscopy (ARPES) and inverse photoemission spectroscopy (IPES), as well as theoretical modeling based on density functional theory. The experimental band structures are consistent with the density functional calculations. The results demonstrate the presence of a dispersive valence band in MAPbBr3 that peaks at the M point of the surface Brillouin zone. The results also indicate that the surface termination of the CH3NH3PbBr3 is the methylammonium bromide (CH3NH3Br) layer. We find our results support models that predict a heavier hole effective mass in the region of -0.23 to -0.26 me, along the Γ (surface Brillouin center) to M point of the surface Brillouin zone. The surface appears to be n-type as a result of an excess of lead in the surface region. © 2016 American Chemical Society.