Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

Development of advanced coal cleaning process; Kodo sekitan kaishitsu gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Osaka, S [Center for Coal Utilization, Japan, Tokyo (Japan); Akimoto, A; Yamashita, T [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

1996-09-01

This paper aims to develop a clean coal production process which excellently removes environmental pollutant, is low-costed, and need no particular systems for distribution of products. The result of the development was described paying attention to column flotation which is a technology to high-efficiently select particulate regions, particulate heavy media cyclone, magnetic separation, and the basic design of the process into which those above were integrated. The two-stage selection process, which is an integration of column flotation and particulate heavy media cyclone into the conventional coal preparation equipment, can produce low-ash clean coal at high separation efficiency and also suppress the rise in processing cost. This process was also effective for removal of sulfur content and trace metal elements. The use of clean coal at power plant can be effective for not only the reduction in ash treatment amount, but the aspect of boiler operation characteristics such as heat transfer efficiency of boiler furnace wall, ash related troubles, loads of electrostatic precipitator, loads of flue gas desulfurization facilities. 17 figs., 5 tabs.

Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

NEDO Forum 2000. Industrial technology development session; Sangyo gijutsu kenkyu kaihatsu session

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This session presented the following subjects: I. IT innovation, II. Bio-seminar, III. Nano-technology, IV. Machine technology seminar, and V. 'Development subsidy project to put industrial technologies into practical use'. The theme in I relates to (1) influence of IT innovation on the society, (2) the theory of semiconductor evolution, (3) the theory of liquid crystal evolution, and (4) the theory of disk evolution. The theme II searches (1) how far have bio-technologies come?, (2) search of human evolution from genes, (3) can human being live up to 150 years by bio-technologies?, and (4) what is a DNA array (chip)?. The theme III covers (1) product innovation in polymers (new polymeric materials brought about by polymer nano-technology, taking polyolefin as an example), and (2) creation of ceramics materials by using nano-technologies. The theme IV relates to (1) ITS changes the car society into this way, (2) the current status and outlook on research and development of micro-machine technologies, and (3) the futuristic society and new industries opened by the Humanoid project. The theme V describes (1) practical application of ultra-small medical device production technologies, (2) development of next generation semiconductor manufacturing resists, (3) development for practical application of an optical brain function imaging device, and (4) development for practical application of new screening technologies toward creation of medicines using genome. (NEDO)

Fiscal 1997 report on technological results. R and D on micromachine technology (Development of micro-factory technology); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Activities are conducted in search of a micromachine system in which devices and equipment relating to machining, assembly, transportation, inspection, etc., in use for a manufacturing process are integrated in a narrow space, for the purpose of conserving energy through the miniaturization of the process of manufacturing small industrial products. With the activities in the two fields of (1) R and D of systematization technology (experimental system for micro fabrication/assembly) and (2) comprehensive investigation and research, examination on detailed specification for the experimental system was carried out, as were the examination of element technologies, element device operating experiments, technological investigation, etc.. In (1), sophistication of the element technologies was contrived that were required for realizing each experimental system, while the detailed specification of each experimental system was decided. Further, a part of the element devices was experimentally manufactured, with the basic functions verified. In (2), research studies were compiled on radio interference for example in the case where various devices were integrated and highly densified through the formation of a micro-factory; also compiled was a joint research with Agency of Industrial Science and Technology, a research conducted for the purpose of building the conception of the micro-factory. (NEDO)

Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of microfactory technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The goal is to save energy and minimize the working space by constructing a manufacturing system comprising various micromachines with their dimensions fit for parts and products they handle. Development continues relative to microprocessing (electrolysis, and optical processing) and microscopic liquid operation (micropump, and part holding device). Under research in relation to the assembly process are a micro-arm to handle tiny parts and precision techniques for interfitting within a very small microfactory, a piezoelectric actuator for microscopic position adjusting, and ultraprecise microprocessing techniques indispensable for their manufacture. Also under research are the incorporation of optically driven microdevices developed before the preceding fiscal year into a microfactory and the study of microservo actuators capable of sophisticated positioning and velocity control. Concerning the microscopic transport system to deal with microscopic parts and products, studies are under way so as to embody systems driven by actuators of the electromagnetic type and electrostatic type. In this paper, reference is made to inspection techniques and comprehensive investigations. (NEDO)

FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell / low-cost and large-area module / next-generation thin-film solar cell (Manufacture of thin-film polycrystalline solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Fiscal 1997 is the first year of another 4-year-long research and development phase. In addition to researches for improving on thin-film polycrystalline Si cell efficiency that have been under way, new efforts are started, which include the development of practicality-conscious thin film producing technologies aiming at higher throughput and yield and the development of modularization process technologies which are necessary for putting thin-film cells to practical use. Concerning the formation of a power generation layer on a polycrystalline Si thin film formed by the ZMR (zone-melting recrystallization) process, studies are conducted for improvement on its throughput and yield using a new CVD (chemical vapor deposition) unit. A method of modularization is evaluated, which involves a laminate of a thin-film cell attached to a resin-coated, reinforced glass substrate and an EVA (ethylene vinyl acetate) back film. A remarkable achievement is earned toward the practicalization of technologies of thin film formation enhanced in quality and throughput and technologies of thin film modularization. (NEDO)

Achievement report for fiscal 2000 on research and development of key technologies for superconducting generator. Research and development of key technologies to increase density, research and development of key technologies to increase capacity, research and development of design technologies, and research of technologies; 2000 nendo chodendo hatsudenki kiban gijutsu kenkyu kaihatsu seika hokokusho. Komitsudoka kiban gijutsu no kenkyu kaihatsu / daiyoryoka kiban gijutsu no kenkyu kaihatsu / sekkei gijutsu no kenkyu kaihatsu / gijutsu chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Researches have been made to increase density of 200,000-kW class generator and to increase capacity of 600,000-kW class generator necessary for putting superconducting generator into practical use. This paper summarizes the achievements in fiscal 2000. In the study of increasing densities of superconductors and field windings, strands were fabricated, in which aging heat treatment conditions, number of aging, and processing degrees between each aging were varied, to increase the critical current of Nb-Ti strand, wherein as high critical current as corresponding to about 90% of the target was obtained. Possibility of increasing the critical current with the final processing degree in the range of 4 to 5 was verified from the relationship between the final processing degree and the critical current. In the study of increasing capacities of superconductors and field windings, findings were acquired on enhancement of conductor stability and reduction in AC loss, with regard to superconductor strands well balanced in the two elements. Prospects were obtained in achieving the AC loss of 200 kW/m{sup 3} in the targeted superconductor. The residual resistance ratio was found to be 200, showing sufficiently high value, and sufficient function was verified in the stabilized copper. In the research of design technologies, primary basic design was performed. (NEDO)

Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Formation of low-temperature film); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usukau taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (teion maku keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A polycrystalline Si thin film formation technology is developed, which uses the flux process in which a reaction occurs between the target crystal and a flux component which is eutectic. Using this process, a crystal grain relatively large in diameter is obtained at a relatively low temperature. This method is now attracting attention as one of the technologies for producing crystalline Si film for use in thin-film polycrystalline Si solar cells. Especially when Al is used for flux, since Al is automatically doped into the target crystalline Si film, it is expected that the resulting film will serve as the ground for a photoactive layer provided with the BSF (back surface field) function which is important for the improvement of solar cell efficiency. A polycrystalline Si thin film is formed on a 2cm times 2cm-large glass substrate at a temperature not higher than 600 degrees C. It is recognized that films selectively oriented towards the (111) or (100) plane are acquired when other processes are employed. It is expected that the said Al-doped film provides a ground on which a BSF function-provided photoactive layer will be formed. (NEDO)

Report on the results of research and development under a consignment from NEDO on deca-nano quantum integrating transistor substrate technologies; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Deca-nano ryoshi shusekika soshi kiban gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches have been conducted on deca-nano quantum integrating transistor substrate technologies, and developments were made on a three-dimensional device simulator which can be used in deca-nano domains, and a circuit simulator to have quantifying function transistors coexist with silicon semiconductor integrated circuits. The researches were intended to develop a simulator capable of analyzing properties of very small silicon and compound semiconductor devices in deca-nano domains. The researches discussed the applicability of conventional simulators, calculated quantum levels in a three-dimensional hetero structure, and resulted in development of an electron wave propagation simulator in optional two-dimensional shapes, a quantum Monte Carlo simulator, and a three-dimensional semiconductor device simulator with quantum correction. On the other hand, in order to estimate characteristics of a hybrid circuit in which single electron transistors coexist with conventional transistors such as CMOS transistors, a single electron hybrid circuit simulator was developed. The development indicated that a CMOS-SET fused memory is promising as a future LSI memory. 22 refs., 116 figs., 3 tabs.

Technological development for super-high efficiency solar cells. Technological development for super-high efficiency singlecrystalline silicon solar cells (super-high efficiency singlecrystalline Si solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (chokokoritsu tankessho silicon taiyo denchi cell no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development of super-high efficiency singlecrystalline silicon solar cells in fiscal 1994. (1) On development of high-performance light receiving layer, the fine electrode for receiving surfaces was designed to reduce serial resistance, and the high-quality oxide passivation film was studied to reduce surface recombination velocity. (2) On development of forming technology of back heterojunction, the high-quality cell with B-doped fine crystalline Si film on its back was studied by heat treatment of the fine crystalline Si film, and the cell structure with high back reflectance of light was also studied. (3) On analysis for high-efficiency cells, the relation between the back recombination velocity at the interface between p-type substrate and back passivation film, and the internal collection efficiency as probe light was injected from the back, was calculated by numerical simulation. As a result, the cell back recombination velocity could be evaluated by measuring the spectral internal collection efficiency to back injection. 15 figs., 6 tabs.

Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T [Electric Power Development Co. Ltd., Tokyo (Japan)

1996-09-01

The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

Technical research and development of long-spanned bridges; Chodai kyoryo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sakai, F.; Yamanaka, M.; Ogawa, K.; Mizukami, Y.; Kano, J.; Watanabe, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1996-10-15

Outlined herein is technical development of long-spanned bridges represented by suspension and cable-stayed bridges. The design of long-spanned bridges requires theoretical analysis of flexibility in which balance after they are deformed by load is taken into consideration. The matrix finite displacement analysis program is developed for optimizing cable-stayed bridge designs and determining suspension bridge shapes as the new major functions. The analysis program, named KASTAN, is also developed for stress analysis of the structure details. A wind tunnel for structure designs is installed to analyze resistance to wind. A number of experiments have been carried out by the tunnel for the designs of segment, main tower and overall bridge models. The means of controlling wind-caused vibration include hydraulic dampers, mass dampers, and combination of high damping rubber and spacer. Cable-stayed bridges are highly flexible, their types being selected by tower height and shape, span ratio and shape of the main beam, and cable position. These bridges constructed by the company include the S-shaped ones whose main beams are supported by cables suspended by two towers of different height, and the others with H-shape towers of high columns which are connected to each other by horizontal beams. 11 refs., 15 figs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of next-generation thin-film solar cell module manufacturing technology - Development of CIS solar cell module manufacturing technology - Development of high-quality film enlargement technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu / kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims to establish a manufacturing process that enables both high-quality CuInSe{sub 2} (CIS) film solar cell enlargement and cost reduction and to develop a device structure which uses less heavy metal for the purposes of increasing the CIS thin-film solar cell size and efficiency and decreasing environmental impact. Several element technologies have been established for increasing the area of high-efficiency Cu(In, Ga)Se{sub 2} (CIGS) solar cells. Concerning the enlargement of the photoabsorption layer which is to assume the most important role, it is found that a high-quality CIGS film, which is near homogeneous though within a 10cm times 10cm area, is fabricated by an in-line vapor deposition method. As for dead area reduction and high-speed patterning, it is found that laser scribing works effectively in the patterning of the window layer and photoabsorption layer. As for reduction in the use of heavy metal, a high efficiency of 16.2% is attained in a cell not using a CdS film as expected in the case of a cell using a CdS film, this thanks to a CIGS film surface reforming technique. The technique of junction formation for CIGS solar cells is improved, and then a true efficiency of 18.5% is achieved. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of high-quality amorphous material/substrate manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A microcrystalline Si thin film is used to form the i-layer of a narrow gap a-Si based thin film solar cell. Since a microcrystalline p-layer is to act as the seeding crystal layer for the microcrystalline i-layer, it has to be very high in crystallinity and therefore is produced under high hydrogen dilution conditions. In this process, a problem arises of the darkening of the underlying transparent SnO{sub 2} electrode. Since this is due to chemical reaction on the SnO{sub 2} surface layer, blackening is prevented by shortening the film fabrication time, and then an excellently microcrystalline p-layer is obtained. Furthermore, by inserting a microcrystalline i-film buffer layer of low fabrication rate into the p/i boundary, plasma damage on the microcrystalline p-layer is inhibited for the fabrication of a microcrystalline i-layer high in crystallinity at high film fabrication rates. A high Voc is then obtained even when the microcrystalline p-layer is very thin. If the hydrogen dilution rate is too low when the i-layer film fabrication rate is high, the initially fabricated layer turns out to be thick to the detriment of film performance. On the other hand, the p-layer or the buffer layer will be etched when the hydrogen dilution rate is too high. The problem is solved by continuously varying the hydrogen dilution rate from high to low during i-layer fabrication. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

Report on achievements in fiscal 1999. Research and development of immediately effective and innovative energy environment technology (Development of immediately effective and high-efficiency solar cell technology, development of high-quality ingot manufacturing technology, and development of high-efficiency cell making technology); 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (kohinshitsu ingot seizo gijutsu kaihatsu / kohinshitsu cell ka gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been made on improving quality of ingots for substrates, manufacturing high-quality thin type substrates, and making high-efficiency cells. This paper summarizes the achievements in fiscal 1999. In developing the high-quality ingot manufacturing technology, discussions were given on a method for assessing impurities and crystal defects by using the total reflection scattering type infrared tomography, and on the optimal solidifying and cooling conditions during the ingot manufacturing by using simulation calculation for solidification. As a result of analyses and discussions, such findings were found effective that the ingot should be solidified through making the solid-liquid interface shape flat, and the temperature falling rate in an ingot should be maintained constant. In developing the high-efficiency cell making technology, discussions were given on the optimal construction based on a simulation that assumes the light sealing structure using the RIE method, and on the optimal construction of polycrystalline silicon solar cells by using a device simulator (PCID). The important factors in achieving a conversion efficiency of 20% are the light sealing structure, surface passivation, and substrate thickness. (NEDO)

FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for fabrication of thin-film solar cells/materials and substrates (Development of technologies for fabrication of high-quality amorphous materials and substrates); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for the amorphous/microcrystalline solar cells with the thin microcrystalline silicon film as the i layer, and the FY 1999 results are reported. The fabrication technologies are investigated for the microcrystalline silicon solar cells of pin or nip structure by RF or VHF plasma CVD using SiH{sub 4} and H{sub 2} as the stock gases. The tests are conducted for evaluating characteristics of the thin microcrystalline silicon film, to investigate the effects of film-making pressure, power and hydrogen dilution rate on the characteristics at a constant film-making temperature of 180 degrees C. The researches on the fabrication technologies for the microcrystalline solar cell of pin structure confirm that use of VHF plasma CVD improves crystallinity, electrical and optical characteristics of the p-type thin microcrystalline silicon film. The researches on the fabrication technologies for the microcrystalline solar cell of nip structure covers transparent substrates, film-making speed of the p layer, power and substrates, and a conversion efficiency of 7.5% is realized by the solar cell formed on a texture substrate. (NEDO)

Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

Report on achievements in fiscal 1999. Research and development of micro-machine technologies (development of micro-factory technologies); 1999 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho. Micro factory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve energy saving by micronizing the manufacturing processes of small industrial products, this research and development is intended to establish technologies to realize a micro-machine system, in which devices for processing, assembly, transportation and inspection used in the manufacturing processes are unified and incorporated in narrow spaces. Fiscal 1999 has performed, on the items of (1) research and development of the systematizing technologies and (2) comprehensive surveys and researches, with respect to the development of the first prototype system, and fabrication on the trial basis of devices to be mounted on the second prototype system, and discussions on further functional enhancement of the different devices. As a result in the research of the systematizing technology, the first prototype system was developed, that unifies the base unit fabricated in fiscal 1998, the electrolysis processing device, the fluid feeding device, the micro-arms, the coating device, the transportation device, and the environment recognizing device. The basic performances of the individual devices on the first prototype system were verified. Based on the result of this function verification, optimal design and fabrication on the trial basis of the devices mounted in the second prototype system were performed, and discussions were given on the further function enhancement in each functional device. (NEDO)

Fiscal 1997 report of the development of high efficiency waste power generation technology. No.1 volume. Element technology development; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (yoso gijutsu kaihatsu). 1997 nendo hokokusho (daiichi bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Following the previous fiscal year, the technology development was conducted of a high efficiency waste power generation system using general waste as fuel. In the development of high temperature high efficiency combustion furnace, a combustion test on the external circulating fluidized bed incinerator was made to obtain data on formation/decomposition of dioxins. Moreover, a combustion test was conducted using mock refuse, petroleum-derived waste and waste plastics, to confirm stabilized combustion characteristics and low pollution. In the development of a corrosion resistant superheater, made were the stress load high temperature corrosion test, study of intergranular corrosion by elements of impurities, etc. In the development of the environmental load reduction technology, conducted was the conceptional design of pulse plasma exhaust gas disposal equipment corresponding to the actual one. In the verification test in a pilot plant, the pilot plant passed the pre-use inspection and was completed in February 1998. In the study of an optimal total system, discussed were the data on the pilot plant verification test, measuring points, how to arrange them, etc. 2 refs., 88 figs., 50 tabs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This research aims to achieve a conversion efficiency of 13% and a manufacturing cost of 140 yen/Wp with a 30cm times 30cm Cu(InGa)Se{sub 2}-based thin-film solar cell submodule. Ga and sulfur are combined and a film fabrication technology was developed which would improve on Voc. Concerning Ga, a laminated precursor layer was fabricated and evaluated, which comprised a Cu-25wt%Ga alloy layer and a Ga source which was a Cu-48%Ga alloy layer. Concerning sulfur, the vapor phase selenization temperature and the selenization retention time in an H{sub 2}Se gas atmosphere was allowed to vary for a change in Cu(InGa)Se{sub 2} calcopyrite crystallinity for the study of relations between the amount of sulfur taken in and the solar cell characteristics, and the relations were assessed by EPMA (electron probe microanalyzer). Technologies were developed for the fabrication of high-resistivity buffer layers by solution growth, for the fabrication of window layers (transparent, conductive ZnO film) by sputtering, and for their patterning. Submodules of a ZnO/Zn(O,S,OH)x/Mo structure were fabricated, 10cm times 30cm and 30cm times 30cm in size. The former achieved 12.5% in conversion efficiency, and the latter 11.6%. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of thin film poly-crystalline solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on a high throughput forming technology and a modularization technology for thin film poly-crystalline solar cell modules. This paper summarizes the achievements in fiscal 1999. In developing the high throughput forming technology for a high-quality thin film, research has been made on a low-cost VEST process to re-utilize substrates by separating the thin film from the substrate. In the melting re-crystallization process, it was discovered that plasticity deformation of the substrate can be reduced greatly by raising the substrate heating temperatures. It was also found out that substrate warping amount can be reduced to about one-fifth of the conventional amount by making the thickness greater than 1.5 mm and raising the heating temperatures higher than 1300 degree C. In developing the thin film modularization technology, it was indicated that the property improving effect remains the same even if the hydrogen passivation method is changed from the hydrogen ion injection to the hydrogen plasma processing. In the trial fabrication of the thin film modules, a conversion efficiency of 13.1% was achieved in nine-cell structured modules. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of thin-film polycrystalline solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to realize the practical application of the above-named solar module expected to exhibit higher efficiency and reliability and achieve cost reduction through consumption of less materials. In fiscal 1998, 1) technologies were developed to reduce substrate warpage during recrystallization for the higher-throughput fabrication of high-quality thin films and 2) technologies were also developed for the realization of higher-throughput fabrication of thin films and for efficiency improvement for thin-film modules. Under item 1), experiments were conducted by simulation for reducing warpage to occur in thin-film polycrystalline Si substrates during fabrication by melting and recrystallization. Under item 2), for the development of thin-film cell high-throughput technologies, studies were started on a more practical hydrogen plasma process to challenge the conventional process of crystal defect inactivation by hydrogen ion injection with which achievement of high throughputs is difficult. For the development of technologies for the enhancement of thin-film module efficiency, efforts were exerted to realize a 10cm times 10cm square shape for the enhancement of efficiency in the process of filling modules with cells. These efforts achieved a great step toward future practical application. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, development of technologies to manufacture next-generation thin film solar cells (development of technologies to manufacture CIS solar cell modules); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (CIS taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was made with an objective to achieve conversion efficiency of 13% in a 30 cm times 30 cm size submodule of a CIS-based thin film solar cell, and to develop a manufacturing technology that can achieve 140 yen/Wp. This paper describes the achievements attained during fiscal 1997. In fiscal 1997, based on the achievements reached during the previous year, a submodule with a size of 10 cm times 30 cm was fabricated for an attempt of improving the open voltage and short circuit current density. Simultaneously, the applicability thereof to a module with an area as large as 30 cm times 30 cm was evaluated. As a result of experimental discussions, enhancement in the open voltage was verified by increasing amount of Ga or sulfur, but it was not possible to achieve 600 mV or higher. In the research of component technologies to establish a mass production process, research and development was made on a high-resistance buffer layer film forming technology, a high-quality window layer film forming technology, a high-quality metallic rear electrode film forming technology, and patterning technologies. The outdoor exposure test was continued on laminated mini-modules with a size of 10 cm times 10 cm. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost large-area module manufacturing technology (Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu, Jisedai hakumaku taiyodenchi mojuru no seizo gijutsu kaihatsu (CIS taiyodenchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was carried out for the production of a Cu(InGa)Se{sub 2}-based thin-film solar cell submodules, having a conversion efficiency of 13% and an area of 30 cm times 30 cm, at a cost of 140 yen/Wp (at a production rate of 100 MW/year). In the effort to fabricate a large-area photoabsorption layer, reproducibility was improved by the introduction of a technique for controlling the Cu/III group ratio in and the thickness of the metal precursor film by the use of ICP (inductively coupled plasma) analysis. A maximum conversion efficiency of 12.93% and a reproducibility of 85% were achieved, which meant that the production cost goal was achieved. In the effort to develop a high-resistance buffer layer fabrication technology, a fabrication method was developed in which a lower limit was specified for solution transparency enabling the completion of the film fabrication process with no colloid formation occurring in the solution. For preventing the high-resistance buffer layer fabrication process from growing too complicated, the steps were integrated into one for the MOCVD-ZnO:B window layer. As the result, the film fabrication process subject to the film fabrication control based on solution transparency was simplified for a great increase in reproducibility. (NEDO)

Development of position measuring technology by GPS; GPS ni yoru sokui gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ishizaki, T [Ministry of Transportation, Tokyo (Japan)

1994-07-25

With regard to the GPS (global positioning system) which uses the satellites launched and administered by the U.S.A. and has been utilized worldwide for ships, automobiles and geodetic surveys in recent years, Ministry of Transport started investigation and research on the application of its position measuring system from FY 1989. In this fiscal year, a study on position measuring methods and selection of the position measuring system to be developed were made, in FY 1991, the real-time functioning and track display were developed, in FY 1992, the initialization aboard the ship, the measure to prevent cycle slip, and the radio data communication technology were developed, and in FY 1993, a long term demonstration experiment presuming its practical use was conducted attaining the expected purpose. In this article, the developed real-time kinematic position measuring system is introduced. Regarding the position measuring methods by the GPS, there are the one point position measuring method and the relative position measuring method. Regarding this newly developed position measuring device, its application to work ships and structures can be considered in various ways. 4 figs.

Development of application technology of ultrasonic wave sensor; Choonpa sensor oyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hosoya, H; Hikita, N; Sasaki, H; Kore, H [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

We have developed parking assist system, which informs a driver the closing point and distance to the objects such as other vehicle, wall and pole around the own vehicle at parking area and makes parking maneuverability easy. This system is based on the range detection technology using ultrasonic wave sensor. We have improved the detecting ability in short range of about 20cm by reducing the reverberation of transmitting wave signal and controlling sensitivities of signal intensity and threshold line. We will show mainly the improvement of short range detection of ultrasonic wave sensor, and briefly the performance of parking assist system. 1 ref., 14 figs., 1 tab.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In relation with several types of standard photovoltaic power generation systems expected to be put to practical use, design parameters are quantified, databases are utilized, and simulation technologies are developed, while collecting data from test facilities constructed to simulate them, for the development of evaluation techniques indispensable for the efficient improvement of photovoltaic power generation systems. In fiscal 1998, data were collected from verification test facilities and residential photovoltaic systems sited across Japan. The collected data were subjected to analysis and simulation, by which correction factors were calculated for smudge, spectral response, incident radiation, and temperature. Furthermore, load matching factors and storage battery contribution rates were calculated by simulation for the stand-alone photovoltaic systems sited in five Japanese cities, each comprising an array, storage battery, charge/discharge controller, DC-DC converter, and a load. Reference is also made to a survey of trends of technology development. (NEDO)

Fiscal 1993 achievement report on New Sunshine Program. Development of photovoltaic power generation system practicalization technology (Development of ultrahigh-efficiency solar cell technology - Development of crystalline compound solar cell technology); 1993 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu taiyo denchi no gijutsu kaihatsu (kessho kagobutsu taiyo denchi no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Efforts are made to enhance InGaP cell efficiency (target 16%) on a GaAs substrate by prolonging the InGaP minor carrier life span. In preparation of InGaP cell fabrication on silicon, a study is made of epitaxial growth of a wide band gap layer. By improving on the conditions of InGaP heteroepitaxial growth under the MOCVD (metal-organic chemical vapor deposition) method on a GaAs substrate, the InGaP cell base layer minority carrier life span is increased to be longer than 5ns. The use of epitaxial crystals greatly improves on the efficiency of InGaP cells on a GaAs substrate. Furthermore, cell structure improvement and the like are accomplished, which results in the achievement of an efficiency rate of 17.4%. As a basic technology for the fabrication of InGaP/Si tandem cells, experiments are conducted of growing a wide gap layer for the growth of Ln{sub 1-x}Ga{sub x}P on an silicon substrate. For the evaluation of epitaxial crystals and interfaces, time resolution photoluminescence measurement is performed and the result is compared with the result of simulation. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Development of energy use rationalization technology); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop self-complete type purification ceramic materials in which selection, separation, and purification functions are merged with the energy conversion function. Activities are conducted in the three fields of developing (1) materials derivation technology, (2) application technology, and (3) common base technology. In relation to selection, separation, and purification functions in field (1), studies are made about electrochemical cell structure control and cell constituting materials for enabling a high efficiency NOx purification reaction. As for the energy conversion function, studies are made about the improvement of characteristics of oxide based thermoelectric conversion materials and about changes in electrical output due to their development into cells. In a study of novel thermoelectric conversion materials, K{sub 2}NiF{sub 4} type Y{sub 0.33}Sr{sub 1.67}(Ni{sub 1-y}Co{sub y})O{sub 4-{sigma}} and Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 1-y}M{sub y})O{sub 4-{sigma}} (M=Fe, Co) are synthesized, and electrical resistivity levels and Seebeck coefficients are determined at room temperature-800 degrees C in an oxygen current. Seebeck coefficients are found to be negative for all specimens, which shows that they are n-type conductors. Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 0.7}Fe{sub 0.8})O{sub 4-{sigma}} exhibits the greatest output factor of 0.064 times 10{sup -4}Wm{sup -1}K{sup -2} (400 degrees C). (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to improve cell efficiency, experiments were conducted for enhancing bottom a-SiGe cell efficiency for the embodiment of an enhanced-efficiency multi-junction cell, for improving crystallinity in microcrystalline silicon through the application of VHF (very high frequency) plasma CVD (chemical vapor deposition), for texturizing metal electrodes on a film substrate, and so forth. In the effort to increase the film fabrication rate, a VHF plasma CVD device was used for studying the effect of the discharge frequency on film deposition and quality, Vpp between the electrodes, and so forth. Studies about the high-throughput production technology centered on the film substrate solar cell process technology and the designing of an optimum geometrical pattern for SCAF (series-connection through apertures formed on film) cells. Production cost was estimated for the SCAF structure film substrate solar cell manufacturing process, and a production cost of 147.1 yen/W (in case of 100 MW/year production) was obtained as achievable under the currently available conditions. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to develop high-performance solar cells, optimum device designs including an advanced light confinement structure or the like were studied, and a 25% reduction in the total power generation layer thickness and a 7% increase in efficiency in power generation were consistently achieved in an a-Si/a-SiGe solar cell. In the effort to develop low-cost process technologies, as the result of studies involving the optimization of high-speed film fabrication requirements such as hydrogen dilution and a high-speed/high-precision patterning method and the like, an initial conversion efficiency of 11.2% was attained, which was the world high for a 90 cm times 90 cm-large a-Si/a-SiGe solar cell. This being equivalent to a post-stabilization efficiency of 10%, the fiscal 2000 target was achieved. A solar cell module production cost assessment was performed based on the result, and a module cost of 133 yen/W (in case of 100 MW/year production) was realized, which again meant the achievement of the fiscal 2000 target. (NEDO)

FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for production of thin-film solar cells and low-cost, large-area modules (Development of technologies for high-reliability CdTe solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for production of low-cost, large-area modules of CdTe solar cells by the high-quality film-making process and high-function patterning, and the FY 1999 results are reported. The research program for the large-area TCO film-making technologies involves investigations on improvement of SnO{sub 2} film quality by the mist method and continuous film-making, which lead to continuous, stable production of 34 substrates of low resistance of 9.7{omega} on the average. The program for production of the large-area, thin-film CdS/CdTe solar cells involves production of TCO and CdS by the mist method, and patterning of the laminated TCO/CdS film by laser scribing. The CdTe film is formed by the atmospheric pressure CSS method, and treated with CdCl{sub 2} to improve its crystallinity. The CdTe film is patterned by sand blasting, and provided with the carbon and silver electrodes by screen printing, to complete the cell. The process is totally effected at the atmospheric pressure, needing no vacuum device. The CdTe solar cell assembly (130 cells connected in series, opening area: 5,413cm{sup 2}), fabricated on a trial basis, achieves a conversion efficiency of 10%. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost and large-area module manufacturing technologies, and new type amorphous solar cell manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to put amorphous solar cells for power use into practical use, research and development has been performed on a low-cost mass production technology for modules with large area and less deterioration using film substrates. This paper summarizes the achievements in fiscal 1999. In developing an efficiency enhancing technology, development of an a-Si/a-SiGe/a-SiGe triple cell structure was launched, and discussions were given on band gaps, film forming conditions, and film thickness. In developing a film forming speed enhancing technology, systematic experiments were performed, as well as theoretical analysis on the film forming mechanism in the plasma CVD process. In developing the process technology for film substrate solar cells, with regard to an a-Si production device of the multi-chamber arranged stepping roll system, six plasma CVD chambers were increased to 13 chambers to improve the electrode forming speed and such processes as drilling low-cost substrates, and laser patterning. In trial fabrication of a triple cell, a module in which one row of the SCAF cell is laminated provided an initial efficiency of 9.64%. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Manufacture of high-reliability CdTe solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The target is a low-cost CdS/CdTe solar cell of a large area (60cm times 90cm), the establishment of mass-production technologies for the cell, and the enhancement of production efficiency. A thin film formation technology of subjecting CdS film organic metal to pyrolysis is established, which reduces photoabsorption loss in the shortwave domain of wavelength of not longer than 500nm, reduces reflection loss in the film, and improves on short-circuit current density. Improvement is also achieved on CdTe film quality and junction quality by use of a proximity sublimation method in a vacuum, when a conversion rate of 16.0% (1cm{sup 2}) is attained which is the highest in the world. Based on the results of the above-said efforts, a 3.3mm-thick glass substrate is employed for CdTe film to develop into a 30cm times 60cm-large size, with the film thereon uniformly thick over a large area thanks to a normal pressure proximity sublimation method. Studies are made toward a process nearer to the ultimate product and, using the patterning technique, a 30cm times 60cm-large CdTe solar cell is tentatively built realizing a conversion rate of 9.8%. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of amorphous silicon-based high-quality material/substrate manufacturing technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu - amorphous silicon kei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to enhance the stability of amorphous solar cells. For elevating TCO (transparent conductive oxide) substrate transmittance to an ultrahigh level and for obtaining amorphous layers less to suffer photodegradation, efforts were made to develop substrate materials stable upon exposure to plasma and low in defect density. In the study of TCO, a high-transmittance glass substrate was employed and TCO was made thinner, and the specimen achieved transmittance of 91.3% or 6.3% over that of the conventional type. In the study of low reflection films, it was found that their transmittance came to be stable and remain so after 150 days after a weatherproof test. In the study for stability enhancement, optimization was carried out for a plasma resisting Ga{sub 2}O{sub 3}-added ZnO film for the manufacture of a substrate material capable of properly behaving in a high-speed a-Si film fabrication process. Low-temperature film fabrication was studied to enable low-cost manufacturing, and it was learned that a 4 times 10{sup -4} ohm/cm low-resistance film was obtained by sputtering Ga{sub 2}O{sub 3}-added ZnO where magnetism was intensive at room temperature, that films excellent in crystallinity were obtained by the same method even at low temperatures, and so forth. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of novel amorphous solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project intends to improve on large-area amorphous silicon solar cell performance and to develop high-throughput manufacturing technologies for a reduction in the cost of modules. A film substrate type amorphous solar cell structure of the serial connection type named SCAF (series-connection through apertures formed on film) is contrived. Under this method, film formation using a stepping roll system newly developed for glass substrates may be applied, and the number of manhours required is allowed to be less than under conventional serial connection forming processes. The new technique is characterized in that serial connections are established via through-holes provided in plastic substrates. Making use of the technology, progress is attained in the development of high-throughput process technology for film substrate type amorphous solar cells and of efficiency enhancement technology. In fiscal 1997, an electron beam unit for plasma generation aiming at the elucidation of reaction processes in plasma was introduced, and technologies based on the equilibrium discharge technique were developed enabling high-speed a-Si film formation without degradation in film quality. The effect of trace boron addition to the tandem cell bottom I layer was investigated, and a stabilization rate of 8.05% was achieved using a 40cm times 80cm large SCAF cell. In fiscal 1998, endeavors were exerted for similar developments. (NEDO)

FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

Fiscal 1998 research report. R and D on super metal (Al system mesoscopic texture-controlled material); 1998 nendo seika hokokusho. Super metal no gijutsu kaihatsu (aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For development of Al materials with superior industrial characteristics (strength, corrosion resistance), this research has promoted development of large-size Al system materials with mesoscopic crystalline texture by high- strain accumulation control technology, and recovery and recrystallization control technology. In this fiscal year, (1) basic study on high-strain accumulation control technology, (2) study on a formation mechanism of ultra- fine crystal grains, and (3) development of a machining process were made. In (1), basic study on low-temperature rolling and study on rolling by rollers having different peripheral speeds were made. In (2), study on refining of recrystallized grains of 5000-base and 7000-base alloys was made. In (3), a low-temperature rolling equipment, and a ultra-rapid heating device were introduced. For the whole R and D project on super metal, the main research facilities such as a low-temperature rolling body for high- strain accumulation and a high-strain accumulative structure formation equipment (melt rolling equipment) for uniform nucleus formation in recrystallization were introduced to gain a firm foothold for the future application research. (NEDO)

Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

Achievement report for fiscal 1998 on the research and development of genome informatics technology. Development of energy use rationalization technologies; 1998 nendo genome informatics gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the field of the analysis of gene expression frequency information, a novel glass coating method and a highly sensitive high-speed reading device are developed. Element technologies are studied for the development of a detection system capable of high-density high-speed reading of high-density DNA capillary array, with a long-chain DNA probe solidified therein. In the technology of transcription control information analysis, concerning the technology of transcription dynamics analysis using tagged transcription control factors, the construction of a model system protocol is studied, an automatic analysis system is developed, and an evaluation technology is also developed. Furthermore, a novel method is proposed, in which two specimens will be prepared, that is, a microbead coupled DNA specimen consisting of base sequences of all combinations of a certain chain length and a cDNA (complementary deoxyribonucleic acid) derived protein specimen, and DNA-protein complexes will be isolated for analysis bead by bead out of a liquid which is a mixture of the said two specimens. (NEDO)

Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; topping cycles; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu bun`ya (topping nensho gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

As a realistic measure to reduce environmental pollutants emitted from coal-fueled boilers, a developmental study was conducted of high-efficient combustion systems. In fiscal 1994, four types of topping cycles which are different in system structure and gasifier type were selected, and topping cycles assuming a 300MW-class power plant were trially designed. Further, an evaluation of adaptability of these systems was made, and an selection of the optimum system for the early development was made among the systems. As a result, the evaluation was obtained that `a system using air blown gasifier` is most suitable for conducting the next-stage research. In the element test on the topping combustion technology, collection was made of data of desulfurization activity, desulfurization oxidation mechanism and alkali metal behavior at the laboratory level, data of temperatures and gas concentration distribution in coal gasification, data of simulation of the gasifier reaction, and the other data. 262 figs., 66 tabs.

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development is conducted for the acquisition of a system evaluation technique for predicting the performance of standard photovoltaic power systems and evaluation technologies applicable to residential photovoltaic power systems different from each other in terms of tilt and direction, district, solar cell type, etc. In fiscal 1999, using data collected from the Hamamatsu field test facilities and residential photovoltaic power systems installed across Japan, various design parameters, such as the irregularity compensation coefficient, temperature compensation coefficient, and the incidence compensation coefficient were determined, and, using the parameters as the secondary estimation values, design parameters were updated. In the development of simulation technologies, basic studies were made about the shadow compensation coefficient, spectral response fluctuation compensation coefficient, and the composition of polyhedral arrays. Moreover, studies were made about the estimation of large area insolation, based on the horizontal surface insolation data collected at 21 sites of residential photovoltaic power systems in the Kanto district. (NEDO)

Development of automatic high-concentration boron measurement technique; Konodo hoso jido sokutei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Maeda, T.; Honda, S.; Ito, A. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

1997-03-01

The technology that can automatically measure the boron concentration in boric acid water was developed. A high-concentration boric acid solution must be held at a high temperature to prevent the deposition. Skill and precision ({plus_minus}0.2 to 0.3% for 10 to 2500 ppm as boron concentration, and {plus_minus}2 to 3% for 2500 to 25,000 ppm) are required to analyze the boric acid solution manually. In theory, the boron concentration in a wide range can be measured, and boron has a constant-temperature function. A density hydrometer method that facilitates the treatment and calibration in high precision and at low cost was chosen. The vibration period generated when vibration is given to the solution specimen put in a U-tube is higher as the density is lower. On the basis of this theory, the density of a specimen can be obtained according to the relation with the same data of the known-concentration boric acid water. The high-concentration boric acid water that cannot be measured by the existing boron densitometer can be measured directly. It can also be measured in a low-concentration area. The technique can be used in a laboratory as the simplified method that is replaced by the current manual analysis. The reduction effect of analytical chemical`s waste liquid can also be expected. In the electric power industry, automated equipment is required for high efficiency and labor saving. 13 figs., 3 tabs.

Development of magnesium semi-solid injection molding; Magnesium han`yoyu shashutsu seikei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sakamoto, K; Sakate, N; Ishida, K; Yamamoto, Y; Nishimura, K [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

Magnesium semi-solid injection molding is safety and clean process. We have investigated influence of molding conditions on mechanical properties and dimension accuracy of products by semi-solid injection molding. As a result it was proved that the accuracy of products by this process is superior to die casting. This advantage as well as better mechanical properties can be utilized for net shape molding of some automobile parts. 4 refs., 8 figs., 3 tabs.

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of manufacturing technologies for low-cost substrates (low-cost Si substrates); Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Tei cost kiban seizo gijutsu kaihatsu (usugata takessho kigan seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on manufacturing technologies for low-cost high-quality Si substrates in fiscal 1994. (1) On the 220mm square type electromagnetic casting technology, development of fast stable casting technology was studied using the previously installed 220mm square type electromagnetic casting furnace. As a result, continuous stable casting was achieved at high casting speed up to 3.0mm/min. Any degradation of crystalline quality due to high speed casting was not found. (2) On the 350mm square type electromagnetic casting furnace, oscillation circuit constants were analyzed for design of the power source for No.4 electromagnetic casting furnace. In graphite heating experiment using the 350mm square type water-cooling copper crucible heated by 1000kW high-frequency power source, sufficient heat quantity was obtained for initial melting of Si. Any problems in Si melting were not found through Al block melting test. 6 figs.

Fiscal 1997 report under consignment from NEDO on photon measuring/processing technology (development of power generation facility use high-function maintenance technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A research/development was conducted on technologies of photon applied measuring/photon applied processing/photon generation which are usable for heightening of reliability and maintenance efficiency of power generation facilities. In fiscal 1997, high melting-point metal particles were manufactured by high energy density laser for formation of high temperature and stabilized fine functional circuit. Further, a wavelength changeable ultra red laser light source was studied which can make in-situ measurement of gas concentration and components. A study was also made to examine the surface composition by measuring fluorescent X-rays emitted by radiating high intensity laser beam on the surface of material. A rod type and a slab type as a high-output complete-solidified laser are under development. There is also a development aiming at high speed/high quality photon processing such as high speed/high precision welding/cutting and laser joining. Besides, a study is being made of high energy pulse/high quality beam complete-solidified laser. The paper made a comprehensive survey of the trend of the photon measuring/monitoring technology, and made a systematical arrangement of the developmental subjects extracted. 142 refs., 357 figs., 62 tabs.

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of HFC-23 destruction technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. HFC-23 hakai gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-01

HFC-23 is produced as a by-product during HCFC-22 manufacturing (produced at by-production rate of about 2%, whereas the reaction control has limitation in reducing the production). This is one of the substances subjected to the greenhouse effect gas reduction in the climate change framework treaty. This paper describes the achievements in 1998 on developing the HFC-23 destruction technology. High-temperature pyrolysis decomposes the substance into HF and CO2, which are given absorption treatment by water and alkali to make them harmless, and are recovered finally as calcium fluoride. An equipment having the treatment capability of 195 kg/h was constructed. Design was made on a facility capable of treating fluorine containing waste water at 3 t/h at maximum. Utilities consumed in a factory (industrial water, acids for neutralization, and alkali) are used effectively to identify the effect of reducing the treatment cost. Discussions were given from the safety aspect on facilities to prevent leakage of fluorine containing waste water being a harmful substance. Fabrication was executed on a full-size treatment testing equipment that can utilize the utilities in the factory effectively, and trial equipment operation was performed to arrange the system prepared toward the future tests and researches. (NEDO)

Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

Fiscal 1997 report of the R and D result of industrial science and technology. R and D on synergy ceramics (development of rational energy use technology); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by transgranularly precipitating nano-size particles from a fine-grain high-density matrix through an improved particle formation process. Its toughness was considerably improved by controlling grain shape and grain boundary structure. A precipitation mechanism was also discussed. 89 refs., 107 figs., 14 tabs.

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells/development of technology to manufacture low-cost large-area modules/development of technology to manufacture next generation thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction); 1997 nendo tiayoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module esizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A thin film single crystal silicon solar cell module is developed, in which a porous silicon layer is formed on the surface of a long-sized single crystal silicon substrate, a single crystal silicon film is integrated on the layer by epitaxially growing the film thereon to form a solar cell, and the solar cell is peeled off from the silicon substrate and transferred to a plastic film substrate. The achievements during this fiscal year may be summarized as follows: simultaneous formation of a porous silicon layer on a silicon substrate, reduction of anode formation current density from 200 mA/cm{sup 2} to 10 mA/cm{sup 2}, development of a silicon epitaxial device using a carbon heater, and attainment of aperture conversion efficiency of 11.8% in a thin film single crystal silicon solar cell. Three kinds of methods were developed to peel off the solar cell. A method was developed to grind silicon substrate surface from which the solar cell has been peeled off. A technology was developed to obtain a long-sized silicon substrate of about 30 cm times 10 cm times 0.1 cm from a 4-inch silicon ingot by using a wire saw. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of high-reliability CdS/CdTe solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Cost reduction for the above-named solar cells is the aim of this effort. On the basis of the results of past studies, a technology is established of fabricating a thin CdS film by subjecting a CdS film to organometal pyrolysis, and this brings about a decrease in photoabsorption loss in the range of waves shorter than 500nm and a decrease in in-film reflection loss for an increase in short-circuit current density. A proximity sublimation method is used for CdTe film fabrication, which improves on film quality and film adhesion. These efforts result in the achievement of a conversion efficiency of 16.0% which is the highest in the world. Studies are promoted in a process nearer to the ultimate form, and a 30cm times 60cm large CdTe solar cell is fabricated on the basis of a patterning technique, and the product attains a conversion efficiency of 9.8%. In fiscal 1998, studies center about the establishment of a film fabrication process for a medium-are substrate and about the enhancement of its conversion efficiency, and facilities capable of dealing with large-area substrates are introduced and operated. In a typical achievement, a CdTe solar cell is experimentally fabricated in a process which is wholly under normal pressure, and the product with an aperture area of 1376cm{sup 2} exhibits a conversion efficiency of 10.5% according to JQA (Japan Quality Assurance Organization). (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of high-reliability CdTe solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Koshinraisei CdTe taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for reliable CdTe solar cell modules, large in area and high in efficiency. In the study of large-area CdS thin film fabrication, a conversion efficiency of 12.5-14.2% was achieved in a cell in a large-area substrate using a mist method-aided process of continuous CdS film fabrication. In the study of large-area CdTe thin film fabrication, the optimization was studied of the base-forming CdS film fabrication conditions and of the CdTe film fabrication conditions in a method using a CdTe powder processed by dry kneading, and a conversion efficiency peak was found to exist when the CdS film thickness was in the range of 700-900 angstrom. In the fabrication of large-area submodules, a large-area substrate was taken up, and TCO (transparent conducting oxide) film was fabricated by the mist method, CdTe film by the normal pressure CSS method, electrodes by the screen printing method, and CdTe film patterns by the blast method. As the result, a conversion efficiency of 11.0% was achieved. In a cost estimation for large-area CdTe solar cell modules, 140 yen/Wp (conversion efficiency: 11.0%, annual production: 100 MW) was obtained. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture high-quality amorphous materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

These technological developments are intended to develop technologies to manufacture with improved quality the silicon-based thin film solar cells. In order to analyze manufacturing conditions for micro crystal silicon thin films as the narrow-gap amorphous silicon-based films, films were manufactured in the vicinity of borders of amorphous/micro crystal silicon film manufacturing conditions. The present film manufacturing did not present effects of suppressing deterioration of hydrogen diluted light. In order to elucidate the light deterioration mechanism in hydrogenated amorphous silicon films and study the suppression thereof, discussions were given on impurities in the film, including oxygen. By using an ultra high vacuum plasma CVD having a thoroughgoing baking system, an oil-free exhaust mechanism, and a raw material gas refining mechanism, impurities were added to and removed from a reaction vessel, and an ultra-high purity Si:H film was manufactured, which has been removed of impurities from the raw material gas, resulting in reduction of O, C and N standing no comparison. According to the result of a light irradiation experiment on an ultra-high purity film obtained under an accelerated deteriorating condition by using a pulse laser, the model assuming the light induced defect and the pair of impure atoms has been denied. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of application type novel-structure thin-film solar cell manufacturing technology - Development of static micro-concentrator solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An acorn type concentrator is a 2-dimensional system and realizes relatively high magnification power, but it requires a special assembly process for modularization because the cells and the concentration system are quite small. Under the circumstances, studies are conducted on a prism array concentrator (PAC) which will demand a smaller burden for modularization. A PAC system is basically a 1-dimensional concentrator in terms of light collection performance. The cell to be attached to one plane in the longitudinal direction of the long triangular prism is so small as 5mm in width, yet it may be as long as 50-100mm, and the conventional flat plate assembly process may be made use of. A concentration efficiency of 82% and a conversion efficiency of 10.9% were obtained from a minimodule with a light intercepting area of 5cm times 4cm. Furthermore, a conversion efficiency of 19.7-21.4% was obtained when a small 5mm-wide cell applicable to a PAC type concentration was used. Since a prism type concentrator optical system will cost much for its molding and strengthening when it is built of glass, inexpensive EVA (ethylene-vinyl acetate copolymer) was utilized as an adhesive filler. (NEDO)

Fiscal 1996 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Technologies were described of creating original high-functional materials. The paper presented the following two as fields of technology on which importance is to be placed for the future R and D from technological and socioeconomic points of view. In the field of new materials of living organism imitation type, remarkably high-performance/high-functional new materials are invented by imitating the precise function manifestation mechanism of the ultimate living organism in which a great variety of matters are in harmony with each other and manifest complicated and high-level functions. In the field of structural control/synthesis process technology, the paper is aimed at manifestation of newer and higher functions/performance and innovation of the synthesis process, and also at developing technology to precisely control structure and process of materials including surface and interface in correspondence with atomic/molecular to macro levels. Up to the present, conducted were an examination of autonomous response materials (the subtheme is a R and D of polymer/composite multi-stimuli-responsive materials) and a R and D of precise polymerization (control) polymer materials. 239 refs., 129 figs., 49 tabs.

Report on results concerning development of supermetal technology (FY1999-2000). Development of evaluation technology for formability of super metal (development of evaluation technology for formability of recrystallized microstructured plate); Super metal no gijutsu kaihatsu seika hokokusho (1999 - 2000 nendo). Super metal no seikeisei hyoka gijutsu nado no kaihatsu (bisai saikesshotsububan no seikeisei hyoka gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In connection with the innovative manufacturing of large base materials having a mesoscopic grain structure by means of technologies for high deformation accumulation control, recovery/recrystallization control, etc., research was conducted on evaluation technology for various characteristics such as formability, with fiscal 2000 results compiled. For the purpose of evaluating average grain size from an optical microscopic photograph of structures, it was judged reasonable to determine the average cut piece length. A device introduced to this development project was a horizontal goniometer capable of ODF (crystallite orientation distribution function)/pole figure measurement, qualitative analysis, and residual stress measurement. With warm rolling performed by controlling both material temperature of 7475 based alloys and roll temperature, thermally stable micro sub-grain structures were obtained. As a result of ODF analysis of this warm-rolled material, it was found that a {beta} orientation group existed very sharply in the area from the sheet surface to the center planar part of the thickness. The grain refinement of 5083 based alloys using a warm rolling method was also successful, with its ODF analysis revealing that the accumulation of the {beta} orientation group was very high as in the 7475 based warm-rolled materials. (NEDO)

FY 1998 industrial technology R and D project. Report on the results of the development of utilization technology of biological resource such bioconsortia system (Development of production technology of biological use petroleum substituting fuels); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Technology development was conducted for production of useful substances using the bioconsortia system. In FY 1998, the development of element technology was studied. As to the utilization technology of gut symbiotic microorganisms such as termite and longhorn beetle, clone types of gut microorganism complex system were analyzed to find out the diversification. In the decay of wood, co-culture of two species of mold fungus was increased in efficiency than single culture. More than 90% was classified/identified of the mold fungi accumulated (in wood piece)/separated for the utilization of plant symbiotic microorganisms. For the production of petroleum substituting useful resource, conditions were established of callus induction from immature embryos of tropical oil crops, especially oil palm, and of regeneration of a lot of small plants from the callus. To establish the Agrobacterium-mediated transformation system of oil palm, the binary vector harboring the reporter gene and selectable marker gene was constructed. Using the vector, oil palm tissues are inoculated and infected with agrobacteria. To heighten the function of palm oil, 10 particular clones were selected from the complementary DNA library obtained from oil palm fruit tissues. The genetic study of germs was also made. (NEDO)

Fiscal 1997 technological survey report. R and D on micromachine technology (Development of high functional maintenance technology for power station equipment); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Activities were conducted in search of micromachine technology for a high functional maintenance system that inspects and repairs abnormal conditions such as cracks in a heat exchanger or a piping system without disassembling it in a power generating station such as a thermal or nuclear power plant. The activities were proceeded in four areas of (1) experimental manufacturing of the system (an inline self-running environment recognizing system, an external inspection system for fine tube group, and a system capable of light internal operation such as welding), (2) R and D on sophistication technology for functional devices, (3) R and D on common basic technologies, and (4) comprehensive investigation and research. In (1), examination of detailed basic specifications was carried out, as were examination of element technologies, experimental manufacturing and operation test of element devices, and performance evaluation. Further, a part of element devices was made on an experimental basis, with the basic functions demonstrated. In the comprehensive investigation and research, a trend in the future maintenance technology in power generating equipment was obtained and pigeonholed. (NEDO)

Research and development of evaluation system for photovoltaic power generation system. Research and development on evaluation technology of photovoltaic power generating systems; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. System hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of evaluation technology for photovoltaic power generating systems in fiscal 1994. (1) On preparation of test facility and measuring instrument, the pyrheliometer with a photovoltaic device as sensor was developed. (2) On collection and analysis of data, operation data of interconnection system, stand alone system, and water pump system were collected, and energy flow was analyzed. The following were also analyzed: time variation of a-Si solar cell modules, fluctuation correction factor of spectrum response, that of nonlinear response of crystalline solar cells, effect of solar radiation intensity and wind velocity on temperature rise of modules, and correction factor of DC circuit losses. (3) On on-site measurement technology, the array output measuring instrument was developed on the basis of capacitor charge system. (4) On simulation technology, simulation analyses of energy flow, optimum capacity of interconnection systems, correction factor of solar radiation, and capacity of array storage batteries were conducted. 3 figs., 6 tabs.

Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; O2/CO2 combustion technology; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu (sanso nensho gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

For the purpose of developing combustion systems in which environmental pollutants are less emitted from coal-fired boilers, conducted in fiscal 1994 were a study of load followability of oxygen producing equipment, and element and basic tests on oxygen combustion systems. Dynamic simulations were made to confirm load followability of low-purity oxygen producing equipment. Further, a test was made on starting time of oxygen producing equipment. As a result of the simulation, favorable load followability was confirmed except for some of the process. The width of variation of the product oxygen purity was {plus_minus} 0.7% at maximum. In the element test on oxygen combustion systems, an experiment on the oxygen combustion using pulverized coal was conducted to study heat collection characteristics of furnace and response to multi-kind of coal. A study of balance of S content, experiments on characteristics of crushing/transporting pulverized coal, etc. were added. There were seen no peculiar differences in CO2 transport and air transport. 216 figs., 31 tabs.

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of CIS solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihtsu (CIS taiyo denchi module no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on a technology to manufacture CIS-based thin film solar cells. This paper summarizes the achievements in fiscal 1999. In the research of a large-area light absorbing layer manufacturing technology, investigation was made on light absorbing layers in manufacturing sub-modules with a size of 30 cm times 30 cm. With regard to the temperature condition in the light absorbing layer forming process, it was found that the cooling rate affects particularly the adhesion in the connecting interface of the light absorbing layer and the Mo rear electrode layer. In addition, it was revealed that the sulfur take-in amount can be increases by extending the retention time at the sulfurizing temperature and by decreasing the temperature to turn the gas phase into selenium. In the research of elementary technologies to establish the mass production process, developments were performed on the high-resistance buffer layer manufacturing technology, the high-quality window layer film manufacturing technology, and the technology to manufacture rear electrode layer made of high-quality metals. In developing the patterning technology, two kinds of the existing patterning devices were modified and adjusted for patterning the substrates with a size of 30 cm times 30 cm. In addition, a processing device was installed in the conventional manually operated process for module finishing. (NEDO)

Fiscal 1997 report under consignment from NEDO on the R and D of femto-second technology (development of ultra short pulse optoelectronics technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku femto gyo technology no kenkyu kaihatsu (chotan pulse ko electronics gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Very high speed electronics technology is indispensable for the creation of industrial base technology which supports high grade informatizing in the 21st century. The state of light and electronics is controlled in the femto-second time domain. As to the development of femto-second light pulse generation/transmission technology, mode synchronous semiconductor laser was manufactured using the strain quantum well structure aiming at heightening profit, and the repeated frequency, 166GHz, was achieved. Relating to the pulse compression element, exciton photonic band was newly designed. A technology of coding was also studied. As to the development of technology of femto-second light pulse control/distribution, shortening of the wavelength down to 1.5{mu}m and a possibility of femto-second domain high speed response were indicated by the combined double quantum well structure. The quantitative measurement of spin relaxation characteristics was successfully made. By the Mach-Zehnder light switch, obtained was the world`s fastest light switching characteristic. To realize the femto-second class very high speed element, conditions were grasped on the crystal growth of Sb based ultra thin films operating in the 1.5{mu}m zone by studying the quantum well using transition among sub-bands. 242 refs., 280 figs., 12 tabs.

Fiscal 1998 research report. Industrial science and technology research project / R and D on creative advanced functional materials (structure-controlled materials) / Harmonized molecular materials; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) seika hokokusho. Bunshi kyocho zairyo no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

R and D on harmonized molecular materials aim at establishment of the technology fabricating self-assembled organic molecular films on solid surfaces which have potentials of mechanical response to electric fields, electroluminescence or optical functions. Molecule harmonization expresses new structures and functions difficult to be expressed by each molecule alone, by cooperative interaction between molecules due to noncovalent bond. Functional thin films were developed by controlling alignment and/or arrangement of molecules with an aid of self-assembling processes. Thiol compounds with larger dielectric anisotropy were synthesized as electric field responsive self-assembled films. {pi}-conjugated compounds composed of phenyl-capped oligothiophenes were synthesized as electroluminescent self-assembled films, and their high crystallinity and efficient electroluminescence were found. Heat- and solvent-resistant lyotropic liquid crystalline (LLC) aligning polymers such as polyamine and polyimine were synthesized as new optically functional LLC dye self-assembled films. (NEDO)

Development of three-dimensional pipe bending technology; Pipe zai no sanjigen mage kako gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, K; Takeda, S [Aisin Seiki Co. Ltd., Aichi (Japan)

1997-10-01

Recently, automotive parts uses move resin products or pipe-like products in order to achieve high quality or light weight. Additionally, the shape of automotive parts becomes more complicated. The rotary stretch bending method, although it is most popular method of bending a pipe, has some problems, such as a bending radius is limited due to use of bending mold, a thickness of an outer side of a bending portion is thinner, and a product is scratched easily during manufacturing. We have developed a three dimensional pipe bending process using a floating expanding plug and confirmed that this method can solve the above problems. 2 refs., 9 figs., 3 tabs.

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and development of technologies to manufacture amorphous silicon/thin film poly-crystalline silicon hybrid thin film solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon / usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Developmental research has been performed on large-area low-cost manufacturing technologies on hybrid thin film solar cells of amorphous silicon and poly-crystalline silicon. This paper summarizes the achievements in fiscal 1999. The research has been performed on a texture construction formed naturally on silicon surface, and thin film poly-crystalline silicon cells with STAR structure having a rear side reflection layer to increase light absorption. The research achievements during the current fiscal year may be summarized as follows: the laser scribing technology for thin film poly-crystalline silicon was established, which is important for modularization, making fabrication of low-cost and large-area modules possible; a stabilization efficiency of 11.3% was achieved in a hybrid mini module comprising of ten-stage series integrated amorphous silicon and thin film poly-crystalline silicon; structures different hybrid modules were discussed, whereas an initial efficiency of 10.3% (38.78W) was achieved in a sub-module having a substrate size of 910 mm times 455 mm; and feasibility of forming large-area hybrid modules was demonstrated. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system /development of technology to manufacture solar cells/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture silicon crystal based high-quality materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi seizo gijutsu kaihatsu, usumaku taiyo denchi seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (silicon kesshokei kohinshitsu zairyo kiban no seizo gujutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is intended to develop thin film solar cells capable of mass production with high photo-stability and at low cost. Thus, the objective of the present research is to analyze the growth process of micro crystal silicon based thin films, the crystal being a high quality silicon crystal based material, and develop technology to manufacture high-quality micro crystal silicon thin films based on the findings therefrom. It was found that, when silicon source is available in cathode, pure hydrogen plasma forms micro crystal silicon films by using the plasma as a result of the chemical transportation effect from the silicon source. It was revealed that the crystal formation due to hydrogen plasma exposure is performed substantially by the crystals forming the films due to the chemical transportation effect, rather than crystallization in the vicinity of the surface. The crystal formation under this experiment was concluded that the formation takes place during film growth accompanied by diffusion of film forming precursors on the surface on which the film grows. According to the result obtained so far, the most important issue in the future is particularly the control of crystal growing azimuth by reducing the initially formed amorphous layer by controlling the stress in the initial phase for film formation, and by controlling the film forming precursors. (NEDO)

Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

FY 1994 Report on the technical results. Research and development of micromachine technologies (Development of highly functional maintenance technologies for power plants); 1994 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This research and development project is aimed at development of the technologies for the micromachines provided with maintenance functions, e.g., for examination and maintenance of abnormal conditions in heat exchangers, piping systems or the like. The initial target is set at establishment of basic technologies for the micromachines, in consideration of the available technologies. The R and D activities are directed to (1) microcapsules for, e.g., micro power generators, (2) mother machines having controlling and instructing functions, (3) non-cabled examination modules, (4) cabled examination modules, and (5) total systems. The item (1) involves the micro power generators, and mechanisms of signal transmission, flaw finding and driving/suspension; the item (2) mechanisms of micro-optics and connection, group controlling, microbatteries, action type controlling, and artificial muscles; the item (3) expansion/contraction type transfer mechanisms, light energy supply, micro visual sensation, function connection, and concerted controlling; the item (4) tubular manipulators, and mechanisms of light-aided power generation and voltage elevation; and the item (5) maintenance and micromachine systems. (NEDO)

Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of environment harmonizing type dye finishing technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. Kankyo chowagata senshoku seiri gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The dye finishing operation in the textile industry places heavy load on the global environment. This paper describes the achievements in fiscal 1998 on development of process to eliminate the load. Low-temperature plasma treatment was introduced into the desizing and refining process to develop a continuous treatment process using no water and chemicals. Quality equivalent to that produced by conventional methods was obtained by applying an appropriate plasma treatment condition. The energy saving rate was presented by reduction by 84.3% converted into steam. Conventional dye finishing operation uses three to six times as much water as the cloth weight. The developed air flow treatment device reduced the water ratio to less than one. This is 86.0% reduction of energy consumption converted to steam. In removing pectic substance in cotton refining, no water, chemicals and steam were used, but were substituted by enzyme for continuous treatment. Good finishing result was obtained by performing bleaching and dying. Enzyme cost is an issue, but the cost would decrease if it is used in large quantity. A two-dimensional colorimeter (measures cloth color with high clarity and reproducibility) and an automatic dye preparing device (with high volume measuring performance) were developed. If the cost required for re-coloring under the present inspection method is converted into energy, it corresponds to 81.6% reduction. (NEDO)

FY 1999 report on the results of the development of technology of super metal. Development of nano/amorphous structure control materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of reducing the amount of energy consumption of transportation equipment such as automobiles, the development is made of innovative metal materials enabling the weight reduction of members relatively on the basis of simple chemical components and by making more substantial improvement of characteristics such as strength and toughness than in the existing metals. For it, the following R and D are conducted in which nano crystal structure and non-equilibrium phase structure such as amorphous are controlled to the limits: 1) particle micro-dispersion technology; 2) high speed super plastic formation technology; 3) high density energy utilization control technology; 4) control cooling technology. In 1), study was made of alloy components and effects of the creation process which are needed for achievement of the nano level of crystal grain. In 2), conditions of vapor deposition and production in high speed particle deposition method are optimally selected, and amorphous and nano crystal structures can easily be produced. In 3), high corrosion-resistant amorphous alloy bulk materials with 5mm thickness and 10mm diameter were successfully trially manufactured. In 4), a bulk amorphous specimen with 10mm outer diameter, 6mm inner diameter and 1mm thickness which was fabricated in the forging method indicated favorable magnetic properties. A method to make a specimen which is more stable is being studied. (NEDO)

Achievement report for fiscal 1997 on development of practical application technology for photovoltaic power generation systems. Development of technologies to manufacture thin film solar cells (development of technologies to manufacture silicon crystal based high-quality materials and substrates / survey and research on analysis of practical application); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu / silicon kesshokei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As a plan to develop technologies to manufacture materials and substrates for thin film solar cells, it is intended to reduce defect density, enhance film forming speed, largely improve the photo-electric conversion efficiency and increase manufacturing productivity. These goals will be realized by establishing methods to control defect density, crystal particle diameters and crystallization rate in silicon crystal systems. A technology to form micro-crystal silicon-based thin films will be developed, that have superior photo-stability, and are capable of realizing low cost and mass production. Discussions will be given on a high-density plasma control technology, a fundamental property evaluation technology for micro crystal silicon thin films, and a device design simulation technology. A technology will be developed to form amorphous silicon layer on a stainless steel substrate by using the plasma CVD process. At the same time, discussions will be given on optical annealing and thermal annealing as reformation methods. Fiscal 1997 has surveyed component technologies to identify and analyze quickly and accurately the technical trends inside and outside the country, and to mass produce thin film solar cells. The Material and Substrate System Technology Subcommittee (silicon crystals) was held to deliberate the four-year development program and its progress. (NEDO)

Achievement report for fiscal 1997 on developing practical application technology for photovoltaic power generation systems under the New Sunshine Project. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, and development of technologies to manufacture new type amorphous solar cells; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, shingata amorphous taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Development will be made on high-performance a-solar cells as part of developing practical application technology for a-solar cells for electric power use. Development will be also made on a low-cost process technology. This paper describes the achievements attained during fiscal 1997. Quality improvement has been realized by using a high RF power hydrogen dilution process on a-Si films for front cells of lamination type cells. Four times faster film forming speed was obtained even by using the VHF plasma CVD process, with film quality equivalent to those made by using the conventional RF process maintained. By optimizing the light enclosing construction, the short circuit current was enhanced by over 20%. Discussions were given on forming homogenous a-Si films by optimizing the conditions for forming films on large-area substrates, which resulted in forming film of 30 cm times 40 cm size with good homogeneity at a film forming speed three times faster than the conventional speed. A surface electrode was formed successfully with good uniformity on a substrate with a size of 60 cm times 90 cm. Productivity greater by over three times the conventional productivity was achieved in patterning of transparent electrodes by using high-output laser. Simultaneous and collective patterning and very small and long size collective patterning were realized in a-Si film selection patterning by using the plasma CVD process. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture application type thin film solar cells with new structure (development of technologies to manufacture amorphous silicon and thin film poly-crystal silicon hybrid thin film solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon/usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was performed with an objective to manufacture amorphous silicon and thin film poly-crystal silicon hybrid solar cells with large area and at low cost, being a high-efficiency next generation solar cell. The research was performed based on a principle that low-cost substrates shall be used, that a manufacturing process capable of forming amorphous silicon films with large area shall be based on, and that silicon film with as thin as possible thickness shall be used. Fiscal 1997 has started research and development on making the cells hybrid with amorphous silicon cells. As a result of the research and development, such achievements have been attained as using texture structure on the rear layer in thin poly-crystal silicon film solar cells with a thickness of two microns, and having achieved conversion efficiency of 10.1% by optimizing the junction interface forming conditions. A photo-deterioration test was carried out on hybrid cells which combine the thin poly-crystal silicon film cells having STAR structure with the amorphous silicon cells. Stabilization efficiency of 11.5% was attained after light has been irradiated for 500 hours or longer. (NEDO)

1998 report on development of high-efficiency waste power generation technology. 2. Development of waste gasification and ash melting power generation technology; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Haikibutsu gas ka yoyu hatsuden gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In regard to waste gasification and ash melting power generation, a basic test and examination were conducted in fiscal 1998, with a full-scale development test made ready to start. In the development of technology for raising steam temperature, evaluation of high temperature corrosivity of SH materials and development of high-temperature dust removal system were carried out for example, as were development of dechlorination technology for thermal decomposition process and development of ceramic high-temperature air heater. In the development of technology to prevent exhaust gas reheating, preliminary examination was made on denitrification technologies using a catalyst with superior low-temperature activity. In the development of technology to reduce self-heat melting critical calorific value, investigation and basic test were carried out concerning a stable waste feed system, with a pilot test device experimentally manufactured and tested based on the findings. In the development of technology for reducing external fuel input, examination and analysis were performed on pretreatment techniques for waste plastics, with basic data obtained for a waste blowing system project. In addition, the thermal decomposition and combustion characteristics of waste plastics were clarified by the basic test. (NEDO)

Report on results concerning development of supermetal technology (FY2000). Development of technology for aluminum-based mesoscopic-structured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of developing high strength alloys through grain refinement, R and D was conducted, with fiscal 2000 results compiled. This year, using hot rolled plates and cold rolled plates of 5083 based alloys, research was carried out on an optimum warm processing method for forming microstructures. When 5083 alloys were rolled with a large reduction by one pass under a warm to hot temperature range, recrystallized grain structures were obtained having 3-4 {mu}m in the surface and 7-8 {mu}m in the center. The proof stress of these specimens was about 1.3 times as strong as an ordinary 5083 alloy soft material while the elongation was about the same. In the case of 7475 based alloys with Zr added in place of Cr, a warm rolling method, in which the alloys were heated to 350 degrees C and repeatedly reheated by one pass at that temperature, was found effective in forming micro-subgrain structures. By the warm rolling method in which roll temperature was suitably heated, it was made possible to steadily form thermally stable microstructures in 7475 based alloys. The 7475 based alloy plate having a microstructure is superior to an ordinary 7574 plate in resistance against stress corrosion cracking. (NEDO)

Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

Survey and research for the enhancement of large-scale technology development 1. Japan's large-scale technology development and the effects; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 1. Nippon no daikibo gijutsu kaihatsu to sono koka

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

A survey is conducted into the effects of projects implemented under the large-scale industrial technology research and development system. In the development of 'ultraperformance computers,' each of the technologies is being widely utilized, and the data service system of Nippon Telegraph and Telephone Public Corporation and the large computer (HITAC8800) owe much for their success to the fruits of the development endeavor. In the development of the 'desulfurization technology,' the fruits are in use by Tokyo Electric Power Co., Inc., and Chubu Electric Power Co., Inc., incorporated into their desulfurization systems. Although there is no practical plant based on the 'great-depth remotely controlled submarine oil drilling rig,' yet oceanic technologies and control methods are being utilized in various fields. The 'seawater desalination and by-product utilization' technologies have enabled the establishment of technologies of the top level in the world thanks to the resultant manufacture of concrete evaporator and related technologies. Eleven plants have been completed utilizing the fruits of the development. In the field of 'electric vehicle,' there is no commercialization in progress due to problems in cost effectiveness though remarkable improvement has been achieved in terms of performance. Technologies about weight reduction, semiconductor devices, battery parts and components, etc., are being utilized in many fields. (NEDO)

Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of advanced-function maintenance technology for power generation facilities; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Technologies for integrating functions are studied for a self-propelled surroundings recognition system that travels in a small-diameter tube at power generation facilities. Parameters are analyzed, and piezoelectric locomotion devices are reduced in size. A disk shape microantenna is experimentally built and evaluated, which is for realizing energy supply and communication by means of microwaves. Studies are conducted to improve the performance of optical energy transmission devices and to realize their systematization. Basic specifications are established for the embodiment of CCD (charge coupled device) microcameras to be installed. A high-efficiency, high-reliability micromachine system is constructed, in which multiple machines coordinate with each other for the exterior inspection of groups of small-diameter tubes. Devices which are capable of driving, deceleration, and propulsion prove to be feasible. Basic specifications are established for microconnectors to connect, separate, and combine multiple machines as occasion calls. Also discussed is the development of a micromachine for tube interior check and repair which operates making use of the inspection hole enabling tube interior check and repair without the need of disassembling the equipment to be repaired.

Research and development of evaluation system for photovoltaic power generation system. Research and survey on test and evaluation method for BOS component devices; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Shuhen gijutsu hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of the evaluation method for BOS component devices in fiscal 1994. (1) On the study on requirements of BOS component devices for practical use, the study results on storage battery, inverter, protective device for system interconnection, and effective use means for storage battery were summarized. On the future device technology, it was clarified that the following value added technologies are promising: simple design of inverter circuit, cost reduction by common specification and mass production, and stabilization of voltage and compensation of momentary peak load by combining inverter with small-capacity storage batteries. (2) On the study on the performance test method for BOS component devices, basic characteristic (capacity, efficiency) test, PSOC charge/discharge cycle test, and accelerated life cycle test were performed for 4 kinds of new storage batteries developed by NEDO. The whole characteristic test results satisfied specifications, and long-term cycle test is in promotion for all new storage batteries. 3 figs., 4 tabs.

Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (development of high-efficiency production process technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (kokoritsu seisan process gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Development is made of high energy-efficiency laser processing technology and high efficiency/high grade photon generation/control technology as laser light source, for the purpose of energy conservation/efficiency heightening of production processes which require a large amount of energy such as welding, joining, surface treatment, and particle fabrication. As to keyhole dynamics of the molten metal generated on the laser weld, construction of simulational mathematical models was started. Equipment to fabricate semiconductor ultrafine particles which become the core of quantum dot functional structures was designed to fabricate particles. In-situ optical measuring technology was studied of element/size of particles of below 30 nm in size by emission spectroscopy associated with the plasma irradiation. As tightly focusing all-solid-state laser technology, studied was the wavelength conversion method in which harmonics are generated four times as much as the fundamental wave due to high efficient generation of high power UV laser. Also studied were high laser strength, low optical losses, conditions for fostering high homogenity crystals. Technology for high accuracy processing of element surface was established. High efficiency photon generation technology was comprehensively investigated. 140 refs., 276 figs., 46 tabs.

Fiscal 1997 research report on the R and D project under a consignment from NEDO. Photonics engineering (R and D of photonics measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Photon keisoku kako gijutsu (photon keisoku kako gijutsu no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Survey was made on the trend of R and D on photonics engineering to clarify the direction of its impact and ripple effect on industrial fields. Reduction of environment burden, improvement of the productivity and reliability of products, and creation of new industries by novel creative R and D are necessary simultaneously. For reconsideration of the previous measurement and machining technologies in a manufacturing industry, use of photon (laser) beams is promising. As photonics engineering, photonics measurement and machining, and elemental and peripheral technologies for generation and control of photon were surveyed. Photonics application technologies for medical care and diagnosis, communication and transmission, entertainment, and chemical fields were also surveyed. In fiscal 1997 as the first year of this project, based on the results obtained in leading researches conducted until fiscal 1996, some technological issues were clarified through the survey on the latest trend of photonics engineering in measurement, machining and generation fields, and its feasibility in the other fields. 265 refs., 91 figs., 10 tabs.

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of manufacturing technologies for low-cost substrates (technical development for production of high purity silicon); Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Tei cost kiban seizo gijutsu kaihatsu (taiyo denchiyo silicon seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of manufacturing technologies of Si for solar cells in fiscal 1994. (1) P in Si could be successfully reduced to 0.1ppmw by EB melting method. The condition possible to reduce P in Si while continuously supplying metal Si was found. The 20kg class EB melting equipment was also designed and manufactured which can be connected with solidifying rough refining process. (2) Use of a water-cooling copper mold was studied using a small melting equipment for cost reduction in solidifying rough refining process. As a result, the prospect of crucible-free technology for removal of P and solidifying rough refining was obtained. (3) B in Si could be successfully reduced to the target of 0.1ppmw by vapor addition method using a plasma melting equipment. (4) The prototype SOG-Si achieved a conversion efficiency of 14.1% as solar cell. In addition, the advanced solar cell prepared by efficiency enhancement process achieved a conversion efficiency of 15.9%. 3 figs.

1998 report on results of technological development of super metal. Innovative technological development for producing advanced structure controlled metallic material (high-speed large reduction rolling technology); 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Kodo soshiki kozo seigyo kinzoku zairyo sosei gijutsu kaihatsu (kosoku daiatsuka atsuen gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A report was made on the 1998 results concerning technological development of super metal. In the 'research and development of super metal', metallurgical examination has been made on crystal grain super refining process using a machining simulator, with studies carried out on crystal grain refining by utilizing large-strain deformation with more than 50% deformation for a single pass and a diploid structure. As a result, it was found that the crystal grain size can be refined to approximately 1{mu}m. Consequently, in fiscal 1998, a high-speed large reduction rolling test equipment was developed capable of rendering a sheathing technology in a mechanically testable size by a rolling method. This test equipment has such capacity as the maximum load of 1,000 ton and the maximum torque of 95 ton/m and is a rolling mill whose scale is largest in the nation on the laboratory level. The rolling speed can be 120mpm, a very fast speed for a large sized rolling mill. Moreover, equipped with an immediate water cooling facility adjacent to the rolls and an automatic operating system for example, it is a high function rolling mill capable of cooling and rolling that render the complex and delicate sheathing technology of super metal. (NEDO)

WE-NET. Substask 4. Development of hydrogen production technologies; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 4. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work), researches were conducted aiming at the establishment of a hydrogen production technology through electrolysis of polymer electrolyte solution. In fiscal 1998, element technologies were developed for the development of high-efficiency/large-capacity water electrolyzing plants using electrodeless deposition and hot pressing, research and investigation of optimum operating conditions were conducted, and a service plant conceptual design and a polymer electrolytic membrane were developed. In addition, literature was searched for the current state of ion exchange membranes and water electrolysis, both indispensable for the hydrogen production technology discussed in this paper. In the field of lamination of large cells (electrode surface:2500cm{sup 2}), an excellent energy efficiency level exceeding 90% set as the target for a large laminated cell performance test was achieved - 92.6% by electrodeless deposition and 94.4% by hot pressing. As for polymer membranes capable of resisting high temperatures, a membrane with an ionic conductivity of 0.066S/cm at 200 degrees C was newly developed. (NEDO)

Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (research and development of composite materials on solar cells under microgravity environment); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (bisho juryoku kankyo wo riyoshita taiyo denchiyo zairyo kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of composite materials for solar cells under microgravity environment in fiscal 1994. (1) On a thin film capillary method, 26 experiments of GaSb thin film crystal growth were conducted using the especially prepared high-accuracy electric furnace under microgravity. The wettability of thin film crystals was improved by refining equipment. Rhombus crystal planes and large crystal grains were observed in GaSb thin film crystals prepared under microgravity. (2) On a liquid phase method, the effect of the gravity on crystal structure and grain morphology was studied for synthesis of CdS fine grains. (3) On technological development of composite materials, the solidification experiment of Cu-In-Se melt was conducted under short time microgravity of 10{sup -4}g for 10 sec. As a result, more uniform texture and more high crystallinity were obtained under microgravity, and In in melt was concentrated by surface tension effect. It was suggested that high-quality CIS thin films will be obtained by Se doping into Cu-In composite films under microgravity environment.

FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the bioconsortium system utilization/production technology); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Fukugou seibutsukei riyo seisan gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing the functional substance production technology, petroleum degrading/cleaning technology and high-grade utilization technology of the unused petroleum fraction, study was conducted of the culture control technology in substance production and substance decomposition by bioconsortia, and the FY 1999 results were reported. As to the functional material production technology, study was made of the separation/culture technology, functional substance production technology using bioconsortia (control substance searching method in the ocean microbial consortia system, isolation of control substance/structure determination/separation of production bacteria, elucidation of the inter-species communication substance function, heightening of function of the production microbial consortia), etc. Concerning the effective degrading/cleaning technology of petroleum compounds, study was made of the molecular genetic analysis technology, histochemical analysis technology, analysis technology of the solvent resistance mechanism, bioconsortia analysis system technology, global environmental purification technology such as the effective decomposition of environmental pollutants, etc. Relating to the high-grade utilization technology of the unused petroleum fraction, study was made of the chemical analysis of the photolysis crude oil, selection of the decomposition microbial consortia, etc. (NEDO)

Fiscal 1994 achievement report. Development of photovoltaic power generation system practicalization technology - Development of ultrahigh-efficiency solar cell technology (Development of new photoelectric conversion material technology - Research on future feasibility of wet-type solar cells); Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Chokokoritsu taiyo denchi no gijutsu kaihatsu (shinkoden henkan zairyo no gijutsu kaihatsu (shisshiki taiyo denchi no shoraiteki kanosei no chosa))

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

A survey is conducted of wet-type solar cells that may constitute an important field in solar chemistry. The wet type solar cell made known by Graetzel et al. in 1991 is a combination of ultrafine TiO{sub 2} grains and a sensitizing dye. The ultrafine grain surface structure enlarges the area of an electrode for the absorption of 46% of incident solar radiation of which 80% or more is converted into electric power. The fill factor at 520nm of a cell fabricated for an additional test turns out to be 40% against the 76% mentioned in technical literature, and the conversion efficiency 10%. The Titanyl sulfate is also tested because it is low in price as material for titanium oxide. Functional groups are experimentally introduced for the generation of bonds on the substrate to be effective in the injection of a sensitizing dye. A sensitizing dye with two carboxyl groups and two bipyridine rings as ligand is allowed to be supported by TiO{sub 2}. IR (infrared) spectrometry is performed, and then formation is found of ester-like bonds or chelate bonds due to the interaction of carboxyl groups and the substrate surface. This is enhanced by surface treatment. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the environment friendly type production technology. High-functional chemical synthesis bioreactor (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of developing production technology of chemical substances which are resource conservative, energy saving and less in environmental loads, a R and D was conducted of a high-functional chemical synthesis bioreactor. The paper reported the results of fiscal 1996. As for proliferation control breeding technology, relating to the switch control technology of proliferation related genes by regulatory factors, the effectiveness on an incubator level was demonstrated, and at the same time improvement of reactor performance in using this technology was studied on paper. As to the manifestation control breeding technology, the actual design of the development of manifestation promotion technology by bent DNA, etc. was proceeded with, and at the same time the following were commenced: selection of bent DNA, confirmation of bent characteristics, and work of vector construction using candidate bent DNA. Further, the simple assessment system of manifestation vectors was constructed. In the development of bioreactor system technology, the actual design was started of the two-stage culture continuance system which separated proliferation and enzyme production. 48 refs., 41 figs., 6 tabs.

Achievement report in fiscal 2000 on technical development to recycle waste building materials and glasses. Development of waste building material recycling technology (Research and development of wooden board manufacturing technology using demolished building lumbers); 2000 nendo kenchiku glass nado recycle gijutsu kaihatsu seika hokokusho. Kenhciku haizai recycle gijutsu kaihatsu (kenchiku kaitai mokuzai wo mochiita mokushitsu board seizo gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development has been made on a wooden board manufacturing technology re-utilizing demolished building lumbers and waste plastics with an intention of saving resources and reducing wastes. This paper summarizes the achievements in fiscal 2000. In developing the technology to re-use demolished building lumbers, a method for removing metals attached to demolished building lumbers was established by using a magnetic separator and a metal detector, with which it was verified that iron can be removed nearly 100%. With regard to waste plastics, simultaneous use of specific gravity separation utilizing centrifugal force and electrostatic separation provided a prospect that metals and plastics of high melting points can be removed from mixed resins in waste household electric appliances, and that polypropylene (PP), polystyrene (PS), and ABS can be classified at high accuracy. In manufacturing waste wood and waste plastic boards, pilot plants were built to use the 'melt spray method', 'melt blow method', and 'laminating method' as the means to spray molten resin onto wood raw materials, wherein trials were performed on mixing molten resins with wood flakes, and on board forming. (NEDO)

Industrial science and technology research and development business for fiscal 1998. Research and development achievement report on glycoconjugate production and utilization technologies (Development of technologies of glycoconjugate-aided CO{sub 2} fixation and utilization); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu seika hokokusho (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Enzymatic and chemical methods were combined and methods were developed for synthesizing mucin type sugar chains and glycopeptides. The influence of sugar chain positions and structures on glycoconjugate stereo structures and physiological activities was analyzed, and glycopeptide structural activities and glycoconjugate remodelling were studied. To create an industrial advantage in a glycoprotein production system by use of zooblasts, sugar chain structure control through sugar transfase occurrence control was studied. For the production of man-adaptive sugar chains using yeast, new yeast variations were subjected to molecular breeding, and tested for the resultant improvement on productivity. Sugar chain marking and refining techniques and various responding mechanisms on the solid surface were elucidated, which enabled structure analyses using sugar chain recognition molecules such as lectins and antibodies. A database on interactions between sugar chains and sugar chain recognition molecules was constructed using the said findings. An analyzing program was also formulated tentatively. This paper also covers general surveys and studies on technologies of producing and utilizing glycoconjugates. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Dissolution/deposition method); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (yokai sekishutsuho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to manufacture the above at low cost by a dissolution/deposition method. Under this method, a film is fabricated containing crystals high in quality and large in size though the film area is very small. In fiscal 1998, an effort to fabricate a film to cover a 10cm square substrate failed. The failure is explained by that the heater was too small for the substrate area and that the failure to uniformly heat the substrate resulted in an inplane temperature distribution greater than expected. The furnace was modified in a minor way to narrow substrate temperature distribution as much as possible. Another attempt was made to fabricate a larger-area film on a 5cm square substrate, and then crystals grew to cover approximately the whole surface of the 5cm square substrate. Efforts will continue to achieve the goal. As for the mechanism of film fabrication on substrates of different kinds, self-coating is now described by difference in heat conductivity between a carbon substrate and silicon substrate. Thanks to individual control in a small film fabricating unit, a film thickness of approximately 100 micrometers was achieved. The distance of diffusion was 30 micrometers or more in the case of a small area, and the efficiency of a solar cell using this film was found at 10.2%. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules (dissolution and deposition process); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (yokai sekishutsuho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was performed by noticing on the plasma spraying method as a process that can manufacture thin poly-crystalline silicon films at a high speed. Fiscal 1997 has established a technology that can form a silicon film directly without using seed crystals in an area of 2-cm square on a carbon supported substrate by using a small film manufacturing equipment using the dissolution and deposition process. The size of the crystal is as very large as several hundred {mu}m, by which a possibility of making high-performance solar cells was verified. Discussions were given to apply this technology to large-area substrates, whereas a device was developed, which is capable of forming a film in an area corresponding to 10-cm square. According to a film forming experiment using this device, the film has begun being formed on part of a 10-cm square substrate, verifying the effectiveness of this method. While the film thickness is about 100 {mu}m, it was confirmed that the crystal size will not change even if the thickness is made mechanically as thin as about 50 {mu}m. Further discussions were given on enhancement of wettability by means of coating, and light enclosing structure. (NEDO)

Development of production technology for deep-seated geothermal resources; Shinbu chinetsu shigen seisan gijutsu no kaihatsu gaiyo

Energy Technology Data Exchange (ETDEWEB)

Wada, T.; Akazawa, T. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1997-11-01

In order to increase the geothermal power generation volume in Japan furthermore after now, it is necessary to develop the deep-seated geothermal fluid collecting technique at 3,000 to 4,000m in depth and about 350degC. In order to collect the deep-seated geothermal resources economically and effectively, there are some principally important problems on production techniques such as P (pressure)-T(temperature)-S (flow rate)-D (fluid density) logging technique, P (pressure)-T (temperature)-C (chemical composition) monitoring technique, high temperature tracer monitoring technique, scale monitoring technique, scale protection and removal technique and so on. The PTSD logging technique is a measuring technique for collecting some data necessary to conduct production management effectively. The PTC monitoring technique is a technique for collecting data on the geothermal resources essential for the resources evaluation and presumption, and tracer monitoring technique is a technique for collecting actual measurement data of fluid flow analysis in the deep-seated geothermal resources. And the sale monitoring is a technique for collecting data on various kinds of scale components of the deep-seated geothermal water and in the steam. In this paper, these techniques are summarized. 8 figs.

Fiscal 1992 survey report. Coal hydrogasification technology development; 1992 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. In the study of coal hydrogasification, a mathematical simulation was implemented to estimate the distribution of products with the pyrolytic reaction and the hydrogenolytic reaction controlled independently in the ARCH-2 (advanced rapid coal hydrogasification-2) process, the said two reactions representing the key concepts of the ARCH-2 process. It was then disclosed that a two-stage reaction control would increase the liquid yield. Also, a tentative calculation was made of gas cooling efficiency and cost performance in a process capable of achieving the target liquid acquisition rate. It was then found that BTX (benzene, toluene, xylene) production up to approximately 15% in terms of carbon was feasible and that the SNG price would be 29.03 yen/Nm{sup 3} with benzene priced at 90 yen/kg, these promising a better result than in the ARCH-1 process. The gas cooling efficiency of the ARCH-2 process was but 72.0% or less, however, which demanded improvement. Studies were made, based on the results of studies in progress since fiscal 1990, about what the hydrogasification process for Japan to develop should be. (NEDO)

Fiscal 1993 survey report. Coal hydrogasification technology development; 1993 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. The hydrogasification process that Japan should develop is a flexible process that operates on the three modes of the maximum SNG yield, the maximum heat efficiency, and the maximum BTX (benzene, toluene, xylene) yield. Such being the case, an ARCH (advanced rapid coal hydrogasification) process was proposed, provided with a reactor capable of an ARCH-1 type operation for the maximum gas cooling efficiency and an ARCH-2 type operation for the maximum liquid yield. As for the details of the ARCH process development, the time and priority for development were determined for each of the items in consideration of the technical contents and the steps of development in the flow from a bench plant to a demonstration plant. The technology of char cooling and extraction was specified as the first item to be immediately dealt with. As for the development of the hydrogasification reactor, it was concluded that it was suitable to begin with the development of an injector. According to the development plan, the cost required up to a pilot plant test was estimated at 2 billion yen. (NEDO)

Development of simulation technology on full auto air conditioning system; Auto eakon no simulation gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Fujita, N; Otsubo, Y; Matsumura, K; Sako, H [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

Mazda has developed simulation technology on control of full auto air conditioning system. We have developed the development tool based on the technology, aiming at higher controllability of full auto air conditioning system and shorter development period. The tool performs simulation on control, on-vehicle evaluation of actual load operation, collecting data and analyzing them by personal computer. This paper reports our verification results on effectiveness of the technology/ and the tool. 4 refs., 9 figs.

Fiscal 1991 survey report. Coal hydrogasification technology development; 1991 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. Dealt with in the survey of basic studies on hydrogasification were the effect of gasification conditions, mechanism of tar decomposition, model-using estimation and assessment of reaction heat, and so forth. In an effort to develop a reactor, the current status was studied and future tasks were extracted concerning the one-through type and the internal circulation type entrained bed hydrogasification furnaces. In the study of practical application of the coal hydrogasification process, it was found that gas cooling efficiency would be increased from last fiscal year's 75.2% to approximately 78% by optimizing the process configuration. An ARCH (advanced rapid coal hydrogasification) process to have a novel reactor was proposed, and, for its commercialization, guidelines for dimensionally enlarging the process were worked out and tasks to discharge at each of the development stages were extracted. Relative to pilot tests, an efficient development program was deliberated, in particular, which comprised ARCH-1 and ARCH-2. (NEDO)

Fiscal 1994 survey report. Coal hydrogasification technology development; 1994 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. For the development of an ARCH (advanced rapid coal hydrogasification) process, a plan was prepared covering the basic concept of the process, overall development program, hydrogen/oxygen burner, and an injector. The overall development program comprises element studies (4 years) and the study of the operation of a 50 tons/day pilot plant (8 years), and deals with the development of a reactor and peripheral equipment. Next comes a total system verification effort using a 200 tons/day verification plant in combination with a hydrogen production process, and this aims to achieve commercialization at 3 million Nm{sup 3}/day. As for the hydrogen/oxygen burner, a structure was proposed after surveys of literature and patents on burner structures, ignition methods, and monitoring methods. In the development of an injector, a plan was prepared for testing, and improving, the performance in a cold/hot model of a specimen incorporating the proposed hydrogen/oxygen burner. Basic studies to be carried out include simulation-aided performance prediction. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of application type novel-structure thin-film solar cell manufacturing technology - Development of amorphous silicon/thin-film polycrystalline silicon hybrid thin-film solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu / amorphous silicon/usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims to manufacture the above for the development of low-cost high-efficiency practical cells. Technologies were developed to homogeneously fabricate films with an average efficiency of 10% or more in a 100mm times 85mm area in a STAR (naturally surface texture and enhanced absorption with a back reflector) structure thin-film polycrystalline silicon (poly-Si) solar cell. The texture shape was improved for a higher light trapping effect and a STAR structure cell highly sensitive to long wavelengths and fit for use for a hybrid cell bottom layer was obtained. Various cells were examined for temperature characteristics, and it was found that thin-film poly-Si cells present a temperature coefficient equal to or less than that of bulk single-crystal silicon systems, and hybrid cells a temperature coefficient similar to that of a-Si systems. The technology was applied to a hybrid solar cell in which an a-Si cell was placed on STAR structure thin film poly-Si cells, and a resultant 3-layer a-Si/poly-Si/poly-Si cell exhibited a stabilization factor of 12.0% after 550 hours of optical irradiation. (NEDO)

Survey and research for the enhancement of large-scale technology development 2. How large-scale technology development should be in the future; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 2. Kongo no ogata gijutsu kaihatsu no arikata

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

A survey is conducted over the subject matter by holding interviews with people, employed with the entrusted businesses participating in the large-scale industrial technology development system, who are engaged in the development of industrial technologies, and with people of experience or academic background involved in the project enhancement effort. Needs of improvement are pointed out that the competition principle based for example on parallel development be introduced; that research-on-research be practiced for effective task institution; midway evaluation be substantiated since prior evaluation is difficult; efforts be made to organize new industries utilizing the fruits of large-scale industrial technology for the creation of markets, not to induce economic conflicts; that transfer of technologies be enhanced from the private sector to public sector. Studies are made about the review of research conducting systems; utilization of the power of private sector research and development efforts; enlightening about industrial proprietorship; and the diffusion of large-scale project systems. In this connection, problems are pointed out, requests are submitted, and remedial measures and suggestions are presented. (NEDO)

Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-30

The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-30

The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

FY 2000 report on the results of the development of the next generation chemical process technology/development of the non-halogen chemical process technology; 2000 nendo jisedai kagaku process gijutsu kaihatsu non halogen kagaku process gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of conserving energy and reducing environmental loads, the R and D were conducted of a new chemical process (non-halogen chemical process) using new catalytic reaction, etc., and the FY 2000 results were summed up. As to the development of a new method to synthesize isocyanate, the development was proceeded with of a method to synthesize diisocyanate by the dicarbamate reaction and pyrolysis of the carbamate, and the effect of catalyst on the yield of carbamate reaction was grasped. Concerning the development of a new synthetic method of epoxides, the development was proceeded with of the catalyst for synthesizing propylene oxides from propylene and hydrogen/oxygen, and conditions were obtained for preparation of a catalyst of the basic catalytic system and with reproducibility. Moreover, the development was proceeded with of a new catalyst used in doing epoxidation of 1-butene using the organic system hydroperoxide. Concerning the development of a new method to synthesize phenol, a promising system was found out by finding out the basic catalytic system of oxidation acetoxyl reaction and proceeding with the search for co-catalyst, carrier, etc. (NEDO)

FY 1999 report on the development of technology to recycle architectural waste materials, glass, etc. Development of technology to recycle architectural waste materials; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

Waste wood materials in the materials discharged from architectural disassembly were regarded as a potential wood resource, and the R and D of the technology to recycle these were conducted. Studies were made on the technology to finely grind waste wood materials, technology to compress/form waste wood materials and ground wood powder, verification of strength characteristics/dimension stability of the formed wood materials, etc. As to the wood materials which were badly degraded under ultra violet rays, they were coloring-processed by the steam treatment, and a possibility of coating substitution was confirmed. In relation to the technology to produce compressed wood materials, the optimization of heat treatment conditions was experimentally conducted. About the technology to give dimensional stability, dimensional stability was improved as a result of the improvement of chemicals feeding and the development of chemically processed drugs. In the development of light formed products, the board was successfully formed which is light in weight using lignocelluloses/inorganic hydrates and has the bending strength higher than that of the plaster board. In the development of interior materials, the technology was developed in which ground wood powder and thermo-plastic resin are mixed for die molding, and the OA floor using this was commercialized. (NEDO)

Report on research and development achievements in fiscal 1980 in Sunshine Project. Development of a technology to measure inside of wells (Development of a fracturing technology); 1980 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho. Fracturing gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This paper describes the achievements in fiscal 1980 in developing a technology to measure inside of geothermal wells, and of fracturing (to achieve enhancement and regeneration of well performance). Design and fabrication were completed on the in-tunnel sensor for a neutron/density logger. The sensor withstood use at a temperature as high as 275 degrees C. In logging and reservoir evaluation field tests, reliable data were derived even at a depth of 1,800 m and a temperature of 250 degrees C. Characteristics of response of radioactivity logging (neutron and density logging) to different igneous rocks were investigated by using rock blocks. For the fracturing facilities, improvements were given on transportation performance and installation workability of the preliminary observation device, by utilizing the experience obtained in the previous fiscal year. A composite (divided into two units) centrifugal multi-stage pumping device was developed so that a water injection test can be performed in a wide capacity range according to the intended wells, where nearly satisfying performance was derived. For the fracturing technology, in order for even small test pieces to be capable of evaluating fracture tenacity accurately with consideration on nonlinear behavior of rocks, elasto-plastic fracture tenacity tests were carried out with AE measurement being performed simultaneously. The paper also describes studies on fracturing fluids. (NEDO)

Report on technological trend survey in fiscal 2000. Survey on bio-technology development strategy; 2000 nendo gijutsu doko nado chosa hokokusho. Bio technology gijutsu kaihatsu senryaku chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Survey and research have been performed on bio-technologies as to their seeds of technological development projects to be worked on by the government from the viewpoint of industrial utilization technologies. In the survey on the trends of research and development and technological development on human-genomes, the survey has been done on the status of execution in the Millennium Genome Project, and how the works related to human-genomes are done at the bio-related government based research organizations and the private sector research organizations. Trends related to the human-genome research in overseas countries were also surveyed. With regard to the future prospect of research and development in the post genome age, discussions were given on the result of the questionnaire survey on opinion leaders in the industrial, governmental and academic areas. In discussing the viewpoint of the industrial utilization technologies related to human genomes, candidates assumed usable in the genome related application fields were discussed, and a basic framework of a technological map was prepared. Based on the results thereof, the technological development areas anticipated to be important in the future were extracted, and the technological development themes were discussed. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture applied type thin film solar cells with new structure and development of high-efficiency hybrid thin film/sheet solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (oyogata shin kozo usumaku taiyo denchi no seizo gijutsu kaihatsu (kokoritsu hybrid gata usumaku / sheet taiyo denchi no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to develop low-cost and high-efficiency hybrid thin film/sheet solar cells, research and development has been performed. This paper summarizes the achievements in fiscal 1999. The research is related to a hybrid construction, in which the upper cells of amorphous silicon thin film are formed on the lower cells bonded with micro-crystalline silicon thin film relative to a poly-crystalline silicon sheet. In the technology to form the upper cells, a pin-construction using amorphous silicon thin film made by using the plasma CVD process was adopted, whereas an open circuit voltage of 1.45V, a short circuit current of 13.6 mA/cm{sup 2}, and a conversion efficiency of 13.5% were obtained. In the technology to form the substrate for the lower cells, formation of flat silicon thin plate that can be peeled off was identified as a result of adopting the construction in which a graphite substrate is provided on a rotating cooling body of 12-prism type. With regard to the technology to bond and form the lower cells, electrical properties of hetero-bonded cells were discussed, and an open circuit voltage of 0.605V and a conversion efficiency of 14.3% were obtained as a result of enhancing the film quality and optimizing the film thickness. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction) (development of technology to manufacture micro light collection type solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

These technological developments are intended to demonstrate module efficiency of a micro light collection type solar cell of 15% by fiscal 2000, and obtain prospect on the module manufacturing cost of 140 yen per watt. Discussions given during fiscal 1997 are as follows: development has been performed on a design method to decide construction of a non-tracking micro light collection type module; in the state of cells being integrated on the module, the cells are arranged minutely and discretely, whereas, with discussions on a method to form them and assessment of the optical system as the main objective, single crystal silicon solar cells with a size smaller than 5 mm were fabricated on a trial basis; problems of forming micro cells by using the wafer cutting process were clarified; micro cells operating on light collection were fabricated trially to extract technological problems in light collecting operation and discuss technical problems in mass production; and development was performed on an evaluation method to analyze the cells' light collecting operation, and discussions were given on a method to estimate power generation amount from the light collection type modules. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

Fiscal 1997 report on the results of the technical development of super metal under consignment from NEDO. Technology to create ferrous mesoscopic structure control materials; Super metal no gijutsu kaihatsu (tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu) seika hokokusho (1997 nendo). Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko (NEDO) itaku kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The fiscal 1997 results were reported of the project on the technical development of super metal which draws out limit performance of ferrous metal and improves the recyclability. In the study of large-strain deformation, a study was carried out with the use of large-strain deformation of more than 50% per 1 pass (strain rate: 0.7 or more) and multi-phase structure. By the crystal microstructuring technology, a level was reached where approximately 1{mu}m crystal size can be obtained. In the study of high magnetic field utilization, the course of study of the structure control and microstructuring was chosen in the preliminary experiment using the existing 8 tesla magnet, and the design and fabrication of a new 12 tesla large-diameter magnet were conducted. In the study of material structure prediction, modeling of microstructuring by recrystallization and establishment of a material predicting method of micro/multi-phase/mixed-grain structures were made the subjects. In the analysis of the mesoscopic structure, the mesoscopic analysis was made of the 0.3C-9Ni steel microstructured by the large-strain deformation thermal processing, and it was shown that the reflective electronic image measured by varying accelerating voltage gives new structural information. 111 refs., 135 figs., 35 tabs.

Report on results for fiscal 1997 on development of coal liquefaction technology . Development of liquefaction base technology (studies on development and internationalization of environmentally benign coal liquefaction technology); 1997 nendo sekitan ekika gijutsu seika hokokusho. Ekika kiban gijutsu no kaihatsu (kankyo chowagata sekitan ekika gijutsu no kaihatsu oyobi kokusaika kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The research objective is the development of environmentally benign coal liquefaction technology and the studies on internationalization of coal liquefaction technology. Implemented for the former are (1) research on improvement and rationalization of liquefaction process and (2) research on advancement of liquefaction base technology. In (1), studies were made on in-oil preprocessing technology and scale suppressing measures for the purpose of obtaining reform/high grade of coal, and on improvement of liquefied oil collecting ratio, sophistication of coal slurry and attainment of light oil/high grade from liquefied crude oil for the purpose of optimizing liquefaction reactive conditions and improving a solvent. In (2), in developing high activity/high dispersion type new catalysts, catalytic sufurization behavior and activity manifestation mechanism were explored, as were iron hydroxide based iron ore properties and liquefaction reactive characteristics. The initial reactive characteristics of liquefaction for example were investigated for the purpose of collecting basic data for expanding kinds of coal. In order to attain the latter objective of the research, a feasibility study of liquefaction location was conducted, as were the investigation including sampling of iron ore for catalytic material and the investigation of coal gasification technology. After the completion of the Australian brown coal liquefaction project, the development of the coal liquefaction technology commenced in fiscal 1994 produced a number of useful records and ended in 1997. (NEDO)

Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

Report on achievements in fiscal 1999 on research and development of the industrial and scientific technology. Research and development of synergy ceramics (development of a technology to rationalize use of energies); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper summarizes the achievements in fiscal 1999 on research and development of a technology to use synergy ceramics as a material, its application technology and the common base technology. In the research of high-function active materials, development was made on catalyst and electrode materials having the selection, separation and rinsing functions, and discussions were given on materials for thermoelectric conversion of oxides. In the research and development of new thermoelectric conversion ceramics materials, searches were made on cobalt and nickel containing compound oxides. In the development of corrosion-resistant electrochemical cell materials, the honeycomb type was devised, and a technology was developed to form honeycombs laminated with different materials. In developing self-lubricating functional materials, silicon nitride with solid lubricant of MoO{sub 3} dispersed on the surface layer was developed, wherein tribological characteristics were evaluated. In developing ultra-smooth low friction materials, studies were carried out on reducing friction by controlling silicon nitride and its surface structure, placing lifter shims in an automotive engine as the application object. The joint research with the National Research Institute performed evaluations on the compound function manifestation process. (NEDO)

Research and development of the industrial basic technologies of the next generation, 'composite materials (quality evaluation techniques)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (hinshitsu hyoka gijutsu)'. Zenki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The results of the first phase research and development project for developing composite materials as the basic technologies of the next generation are evaluated, and the directions of the R and D evaluation for the second phase are set up. The efforts in the first-phase R and D project are aimed at development of methods for measuring carbon fiber surface structure elements; confirmation of the relationship between adhesive shear strength and active surface area; development of methods for determining fracture toughness by standard specimens; estimation of allowable void fraction for inter-layer shear strength; defect detection and quality evaluation by electromagnetic, ultrasonic, laser holography and AE methods; development of methods for detecting resin setting reactions during the molding processes; and understanding deteriorated mechanical characteristics of the resin-based composites by environmental factors, among others. The objectives of the first-phase project have been almost achieved. It is decided that the second-phase R and D project are directed to investigations on the relationship between surface properties of the fibers in the composites and fiber/matrix adhesion; researches on mechanical characteristics involved in fracture of the structural elements; evaluation of mechanical properties of the metal-based composites and investigations on detecting their defects; elucidation of the effects of environmental factors on their strength; and development of the techniques for integrating detection of molding-induced cracking and that of setting reactivity, among others. (NEDO)

Report on results concerning development of supermetal technology (FY2000). Development of technology for high-anticorrosive iron-based microstructured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of greatly improving strength and corrosion-resistance through ultra-refinement of crystal grains of steel materials, research was conducted on microstructure refinement technology utilizing strong magnetic fields and on mechanical property estimation technology for ultra-refined structure steel using computational science, with fiscal 2000 results compiled. In the research for grain refinement utilizing magnetic fields, an inline experiment of transformation was carried out and, as a result, equi-axed grains of 1.6 {mu}m were attained on a 3 mm thick steel plate of commercially used composition by a method of recrystallization after cold rolling. The experiment revealed that the 1 {mu}m grains could be obtained by setting cold-rolling work load to 80%. In addition, data were acquired relating to conditions such as steel composition affecting the formation of orientation in structures, work load and rolling temperature for areas to be recrystallized, holding temperature and time in the magnetic field, and intensity of the magnetic field. In the research for estimating mechanical properties of microstructures by computational science, a Monte Carlo simulation was carried out by employing the result of a polycrystal plasticity method program as the initial value, with a prototype established of the integrated simulation method from the deformation to the microstructure formation. (NEDO)

FY 1992 Report on the results of the research and development of micromachine technologies. R and D of highly functional maintenance technologies for power generating systems; 1992 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

Described herein are the FY 1992 results of the R and D project aimed at development of microcapsules, mother machines, examination modules without retrieval and working modules with retrieval, and their application to total systems for development of the highly functional maintenance technologies for power generating systems. Researches on the microgenerators involve studies and extraction of technical problems for structures, thin-film magnet production methods, coil winding methods, high-speed microbearings and microaccelerators. Researches on the mother machines involve development of the basic elements, on a trial basis, of the electrostatic actuators for the mechanisms of driving the main bodies, and evaluation of their characteristics by a minute torque analyzer. Researches on the examination modules without retrieval involve basic studies on, e.g., expansion driving, supersonic and microwave energy conversion devices for the expansion transfer mechanisms, development of these devices on a trial basis, evaluation of their functions, and extraction of the problems. Researches on the working modules with retrieval involve studies on shape memory alloy materials for tubular manipulators and actuator mechanisms. (NEDO)

Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

Report on achievements in research and development in fiscal 1982 commissioned from the Sunshine Project. Development of a pit condition measuring technology (Development of a fracturing technology); 1982 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho. Fracturing gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Development was made on a measuring instrument intended of acquiring information inside geothermal wells under high temperature and pressure. Research and development was performed on a fracturing technology to enhance characteristics of wells. What have been performed as a result of the development of the in-pit measuring instrument are application of high temperature logging cables as a result of development of logging devices, and the fabrication of a digital data analyzer. In developing the logging and reservoir evaluating technologies, field test were performed by using a logger that uses neutrons, installed with a radiation source. In developing the fracturing technology, discussions were given on the equation of relationship proposed from the standpoint of fracture dynamics, and investigations were made on examples of values, in order to anticipate hydraulic fracturing pressure applied in fracturing. In the research of fracturing additives, discussions were given on gelling agents supported by use of water glass, and alumina prop agents. For the preliminary observation devices, a high-pressure low flow rate control device was installed on the high-pressure plunger pump, improvement was made on the composite centrifugal multi-stage pump. (NEDO)

The maximum allowable temperature of zircaloy-2 fuel cladding under dry storage conditions

International Nuclear Information System (INIS)

Mayuzumi, M.; Yoshiki, S.; Yasuda, T.; Nakatsuka, M.

1990-09-01

Japan plans to reprocess and reutilise the spent nuclear fuel from nuclear power generation. However, the temporary storage of spent fuel is assuming increasing importance as a means of ensuring flexibility in the nuclear fuel cycle. Our investigations of various methods of storage have shown that casks are the most suitable means of storing small quantities of spent fuel of around 500 t, and research and development are in progress to establish dry storage technology for such casks. The soundness of fuel cladding is being investigated. The most important factor in evaluating soundness in storage under inert gas as currently envisaged is creep deformation and rupture, and a number of investigations have been made of the creep behaviour of cladding. The present study was conducted on the basis of existing in-house results in collaboration with Nippon Kakunenryo Kaihatsu KK (Nippon Nuclear Fuel Department Co.), which has hot lab facilities. Tests were run on the creep deformation behaviour of irradiated cladding, and the maximum allowable temperature during dry storage was investigated. (author)

Noise and vibration reduction technology in hybrid vehicle development; Hybrid sha kaihatsu ni okeru shindo soon teigen gijutsu

Energy Technology Data Exchange (ETDEWEB)

Yoshioa, T.; Sugita, H. [Toyota Motor Corp., Aichi (Japan)

2000-03-01

Accomplishing both environmental protection and good NVH performance has become a significant task in automotive development The first-in-the-world hybrid passenger car of mass production. 'Prius', has achieved superior NV performance compared with conventional vehicles with a 1.5-liter engine along with 50% reduction of fuel consumption and CO{sub 2} emissions. low HC, CO and NO{sub x} emissions. This paper describes NV reduction technology for solving problems peculiar to the hybrid vehicle such as engine start/stop vibration, drone noise at low engine speed and motor/generator noise and vibration. It also mentions application technology of low rolling resistance tires with light weight wheels and recycled material for sound proofing. (author)

Research of fluidized bed cement clinker sintering system by pilot plant; Ryudosho cement shosei gijutsu no kaihatsu. 7

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Sato, N; Hashimoto, I; Nakatsuka, M [The Cement Association of Japan, Tokyo (Japan)

1996-09-01

While a cement manufacturing process generally performs sintering by using a rotary kiln, a development work has been carried out as a subsidy operation of the Agency of Natural Resources and Energy on a cement sintering technology using a fluidized bed consisted of two furnaces: a jet flow bed granulating furnace and a fluidized bed sintering furnace. This paper reports the results of tests and researches performed during fiscal 1995. A plant with a scale of 20 ton-a-day production started in 1993 after having gone through bench scale tests. The year 1995 conducted by August its performance evaluation, review of the operation method and the safety criteria, and generalization of the tests. A multi-stage cyclone system has been employed in the preheating equipment for cement material powder. A number of improvements have been realized in the aspects of construction and operation, such as stabilization of dust collecting efficiency by employing a high-efficiency type cyclone, and operation with reduced pressure variation. Based on these results, a construction had been progressed in parallel on a new plant upscaled to 200 ton-a-day production. The new plant was completed in December, 1995. 9 figs., 8 tabs.

Separation of unburned carbon from coal fly ash through froth flotation; Sekitanbai no shisshiki datsutanso gijutsu kaihatsu shiken

Energy Technology Data Exchange (ETDEWEB)

Miwa, T [Center for Coal Utilization, Japan, Tokyo (Japan); Murakami, T [The Coal Mining Research Center, Japan, Tokyo (Japan)

1996-09-01

Coal ash tends to become containing more unburned carbon and porous substances depending on conditions of combustion, whose adverse effects to products due to water adsorbability, absorbability and color tones create obstacles in its utilization. Therefore, research and development works have been progressed on wet type carbon removing technology which is characterized in that coal is pulverized to preferable degrees and subjected to flotation. This paper reports the results obtained during fiscal 1995. The results may be summarized as follows: as a result of the comparison test on a column flotation machine and an FW type flotation machine of machine stirring type, the former machine showed better flotation efficiency; several methods were investigated on crushing as a treatment prior to flotation, whereas a mixer with greater circumferential speed and a homo mixer showed the highest efficiency; strength of the impact to the flotation efficiency was found to decrease in the order of pulp concentration > pretreatment time > collector addition ratio; and as a result of the evaluation on refined ash as a cement admixture and carbons as fuel, possibilities were found in them for practical application. 16 figs., 2 tabs.

Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths/Development of technology to excavate geothermal resources in great depths (Designing whole development); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu (zentai kaihatsu sekkei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Technological development has been made on excavation of geothermal wells, which are dense, hard, and high in temperature and pressure, in developing geothermal resources in great depths. This paper summarizes the achievements in fiscal 1999. This fiscal year has performed the excavation test using an actual well to verify the reliability in practical use of the developed heat-resistant and durable bit. The test was executed by using a bit with a diameter of 8-1/2 inches in a ground bet having a maximum temperature of 300 degrees C in the Yamakawa geothermal field. As a result, good site evaluation was obtained that the wear and tear after lift-up showed no problems, and sufficient performance was verified in the drilling rate and durability. In addition, the low specific gravity cement for high temperature use that has been newly developed was given a cement mixing test to identify its workability at site and hardening properties, at a test well with a temperature of about 40 degrees C in the Okiri geothermal field. The actual well test was performed in a large-scale lost water occurred in a return well during an excavation by Nittestu-Kagoshima Geothermal Company. Effects were recognized in measures to prevent water loss. (NEDO)

Research, development, and evaluation of basic technologies for next-generation industries. Technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu hyoka. Saibo tairyo baiyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

The project aims to establish basic technologies for the mass culture of cells by utilizing the features of animal cells, which will enable a large, stable supply of fine chemicals such as highly functional physiologically active proteins whose industrial production the conventional technique of synthesis fails to realize. For this purpose, efforts are exerted to select cells which are capable of producing target substances, to breed highly productive strains, to develop a serumless medium that satisfies demands for an all-purpose feature and heat sterilization, and to develop technologies of high-density culture and effective refining, etc. Some DNA (deoxyribonucleic acid) recombination technologies are also resorted to. As the result, a high-density culture of 2 times 10{sup 8} cells/ml has become available. Production is now feasible of various differentiation-inducing elements such as monoclonal antibodies with anti-HB virus activity, DIF, etc. Furthermore, cooperation with the Tsukuba University leads to the discovery of a novel vasopressor peptide (endothelin). The heat sterilization accepting serumless medium, which is put to practical use as the first of the kind in the world under this research and development project, contributes to the advancement of basic studies about cell biology. (NEDO)

Survey of the trend of technical development and industrial policies in Asian countries; Asia shokoku ni okeru gijutsu kaihatsu no doko to sangyo gijutsu seisaku ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A sharp rise in industrial productivity in Asia countries indicates a rising level of R and D technology. Since Japan has not clearly grasped the R and D ability in these countries, it has not given appropriate personnel/material R and D support to them. Therefore, for the purpose of exactly grasping the R and D ability of Asian countries (Korea, Taiwan, the Philippines, Indonesia and India) and studying an effective and appropriate method for R and D cooperation, a survey was conducted of R and D potentials in Asia and R and D support policies of the countries. As a result of the survey, the following are taken up as items to be considered: promotion of exchanges between Tsukuba, etc. in Japan and research/university towns and science parks being constructed in lots of countries, participation of private companies in high-tech joint work in cooperation with Japan, sending information from Japan using internet, etc. and exact grasp of needs at partner side, cooperation given to new comers without asking for research results (use of OB researchers, etc.) 25 refs., 39 figs., 59 tabs.

Survey and research on the effects of technological development. Annex (Tables of technology-related data); Gijutsu kaihatsu no koka ni kansuru chosa kenkyu. Bessatsu (gijutsu kanren data list)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Compiled into a report are the data about trends in Japan's research and development efforts broken down by industry covering a period of 1960-1980. The data items are quite versatile, including the number of companies engaged in researches and their rates, number of employees, total sales volume, profits through business, number of employees related to researches, number of dedicated researchers, number of dedicated researchers per 10,000 employees, disbursement of in-house research expenses, rate of personnel expenses to in-house research expenses, rate of disbursement of in-house research expenses to total sales volume, rate of disbursement of in-house research expenses to profits through business, disbursement of in-house research expenses per company, disbursement of in-house research expenses per dedicated researcher, in-house research expenses broken down by purpose (basic research, applied research, research for development), component ratio (basic research, applied research, research for development), number of dedicated researchers per speciality (total number, mathematics and physics, chemistry, biology, geology, engineering, civil engineering and construction, machinery and ship and aviation, electricity and communication, mining and metallurgy, textile, agriculture and forestry, fishery, stock-breeding and veterinarian, medicine and dentistry, pharmacy), number of technologies exported, total sum of export, etc. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the system evaluation technology; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on the evaluation method for the performance prediction system of the standard photovoltaic power system, the R and D were conducted of the system generation output prediction technology which is general-purpose, simplified and applicable to various kinds of photovoltaic power system for residential use, and the FY 2000 results were summed up. In this fiscal year, the photovoltaic power system for residential use was increasingly installed at 15 places, and 100 sites in total were made database and analyzed. As to the development of simulation technology, technology of calculation was established such as the simulation of multi-plane array composition and correction of multi-plane array incidence. Further, technical information on system trouble and knowledge/information/proposal for reducing power generation loss were arranged by design parameter. Using the data on solar radiation/power loss at sites of residential use photovoltaic power systems installed in the Kanto area, value analysis of the capacity of wide area facilities of the photovoltaic power system was made by the statistical method. This study was compiled into the revised edition of design manual. (NEDO)

Fiscal 2000 survey report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Research and development of micrometer-order controlled material creation process technology); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu (micrometer order de seigyosareta material sosei process gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop sub-millimeter order coating creation technologies for engine cylinder bores, valve seats, and the like, for improvement on the performance of tribology related parts, which is necessary to assure environmental preservation, energy conservation, and resource conservation for industrial and transportation equipment. The coating liquid is applied in drops to the object and is irradiated with laser for re-melting for the formation of a coating. The technique is characterized in that it produces a 100 micrometer order coating. Activities are conducted in the four fields of (1) the technology of forming a coating by the use of high energy pulse laser, (2) technology of wear resistant surface treatment, (3) technologies for creating self-heating compounds and for bonding the same in practical applications, and (4) the analysis of the mechanism of tribological characteristics of a coating fabricated by hybrid laser surface treatment. In field (3), an Fe{sub 3}Al coating is fabricated by a combustion synthesis process in which a powder coating is pressed and simultaneously electrified for combustion (reaction), and the result is tested for physical properties. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of establishing the high-grade utilization technology of unused seaweed/algae and production technology of useful substances using high-grade functions of bioconsortia, study was conducted, and the FY 1999 results were reported. In the analysis of the ocean environment adaptation mechanism, the R and D were made of a selection method of the marine microbial consortia using korormicin. In the study of the high-grade utilization technology of unused resources/substances such as marine-producing algae, several tens of the carrageenase producing microbial consortia were acquired from the surface of seaweed, and some carrageenase producing bacteria and non-producing bacteria were acquired by isolating as pure strains. In the study of the petroleum substituting useful resource production technology, developed was a monitoring system of the environmental stress using marine-product invertebrate/micro-algae symbiotic system. In the study of the high-grade utilization of large useful algae, elucidation of the related genes, fabrication of variants and analysis of genes were carried out for the bacterium BUP-7 which indicates activity of growth acceleration/shape formation of seaweed. (NEDO)

Achievement report for fiscal 1981 on the development of solar energy technologies for the development of practical application technologies for photovoltaic power systems. Experimental fabrication of solar cell panels and verification thereof (Development of technologies for panel assembly process); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (panel kumitate kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In a study of cell array connection process, continuous and automatic connection of cells is named as the basic concept in view of low cost and high reliability. In the designing of details of cell strings, CZ (Czochralski) cell dimensions are reviewed for cell packaging efficiency improvement, interconnectors and wiring are examined for a easier packaging process, and solder connection is thought over for utility cost reduction. Conditions are established for string fabrication process details. In the study of the panel packaging process, panel package designing is carried out and a dedicated mechanical device is installed. In the study of the inspection process and plant system, data are collected, necessary for the construction and adjustment of an inspection device. Research is conducted on the layout of plant facilities, on required utilities, and on facilities operating state signals to be transmitted to the central control unit. As for an inspection jig supply system, transfer system, and storage rack, they are designed, built, and installed. The plant house is now complete. (NEDO)

Fiscal 2000 achievement report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Research and development of nanometer-order controlled material creation process technology); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu (nanometer order de seigyo sareta material sosei process gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop tribo-material creation process technologies capable of meeting the needs of environmental protection and energy conservation relative to automobile engine parts such as piston rings, cams, shims, and the like. Activities are conducted in the three fields of (1) the research and development of nanostructure material creation technologies, (2) research and development of tribological evaluation technologies, and (3) the verification of the developed technologies. In field (1), a nanostructure control process is studied, and tribo-composite materials are examined. In field (1), in fiscal 2000, the arc ion plating method is selected as a nanostructure control process, and the closed type nonequilibrium magnetron sputtering method as the base for development into a process. As for tribo-composite materials, Ti-Si-N based and Cr-Si-N based coatings find their feasibility in shims, and Cr-Si-N based and Cr-Si-C-N based coatings in piston rings. Compiled in this report are the summary, and the studies of nanostructure control process technologies, joint studies, composite ceramic coating practicalization technologies, and technologies for putting to practical use coatings which comprise layers of different substances. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. R and D of complex carbonhydrate production/utilization technology (Development of CO2 fixation/effective utilization technology by applying complex carbonhydrate); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugo toushitsu seisan riyo gijutsu no kenkyu kaihatsu (Fukugo toushitsu oyo nisankatanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of making an industrial use of complex carbonhydrate performing an important function in substance recognition, etc., which cannot be realized by only nucleic acid, protein and lipid, the R and D of the basic technology related to the production/utilization were conducted, and the FY 1999 results were reported. In the study of synthesis/utilization/remodeling technology of complex carbonhydrate using the chemical synthesis method, the R and D were made not only on the synthesis of sugar chain but for the synthesis method of the peptide added with sugar chain, that is, glycopeptide. Further, as to the reaction with the aim of the application, there was hope for large-quantity synthesis of milk oligosaccharide by the oxygen method. In the study of the design technology of complex carbonhydrate molecules, the systematical analysis using the model glycopeptide was conducted of effects of the sugar chain addition part and sugar chain structure on the 3D structure and physiological activity. Concerning the synthesis/utilization/remodeling technology of complex carbonhydrate using the biological method, study was made of the animal cell utilization, microorganism utilization, technology of structural analysis of complex carbonhydrate, etc. (NEDO)

Achievement report in fiscal 2000 on technological development to recycle waste building materials and glasses. Development of waste building material recycling technology (Research and development of recycling technology corresponding to grades of demolished building lumbers); 2000 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu (kenchiku kaitai mokuzai no hin'i ni taioshita recycle gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to reduce wastes, and promote effective utilization of wood resources, research and development has been made on a demolished building material recycling technology. This paper summarizes the achievements in fiscal 2000. In developing the technology to manufacture high water resistant wood boards, discussions were given on resor type phenolic resin as an adhesive, and on the medium density fiberboard (MDF) being a substitute material for plywood as the wooden board. As a result, a highly water resistant MDF that can clear JIS E0 has been developed. In the research of a technology to enhance durability of wooden boards, the in-liquid roll press method was devised to perform impregnation of chemicals into board raw materials continually and simply, whose device was fabricated on a trial basis. With regard to recycling of medium to low grade wood-based wastes, researches were performed on pulverization of the wastes, fabrication of liquefied woods, and effective utilization of the liquefied woods. Both of a hammer mill and a chip saw crusher fabricated wood powder with nearly uniform grain size regardless of types of the wood-based wastes. Liquefaction of plywood and PB boards required more stringent reaction conditions than liquefaction of such ordinary members as pillar materials and laminated lumbers. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology - Photovoltaic system data book, separate volume); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu bessatsu (taiyoko hatsuden system data shu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the research and development of photovoltaic power generation system evaluation technology, great progress has been achieved in performance improvement and cost reduction as far as constituent devices such as power modules and inverters are concerned. In the designing of systems, however, quantitative elucidation of loss and power reduction factors remains insufficient. Under the circumstances, several types of photovoltaic power generation systems expected to be put to practical application in the future are taken up, test facilities are constructed which simulate them, and data are collected. The thus-collected data are utilized for research and development of evaluation techniques necessary for the improvement of photovoltaic system efficiency, such as design parameter quantification, databasing and utilization thereof, and simulation technologies, for the establishment of technologies for optimum designs and optimum operations. The data book accommodates data, arranged in an easy-to-use fashion, collected about verification test facility (interconnected systems, independent systems, and water pump systems) operation, weather conditions, and residential photovoltaic power generation systems. (NEDO)

Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects. Solar energy technology research and development; solar panel experiment, manufacture, and verification (Photovoltaic power system practical application technology; ribbon-type crystal substrate process technology); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (ribon kessho kiban kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Carried over from the preceding fiscal year are the development of ribbon crystal pulling technology and the studies of ribbon crystal substrate quality and plant operation. In the development of ribbon crystal pulling process, a pulling drive is built and the limiter mechanism is strengthened for improvement on ribbon crystal flatness, technologies are established for high-speed pulling of broad ribbon crystals, pulling system prototype is built, after-annealing technique is improved for eliminating distortion, and technologies are developed for continuous feeding of raw materials. In the quality examination of ribbon crystal substrates, a method is tested and studied for bringing about a decrease in the number of SiC grains. The object of the plant operation study is a plant capable of producing 250kW-equivalent ribbon crystals a year, and the efforts involve the ribbon pulling system, rough cutter, real-size cutter, etching unit, shape checker, packing, devices for production lines such as warehouses for products, electric power, gas, water, peripheral equipment for waste water treatment etc., ribbon specifications check, quality related assistance equipment to deal with unacceptable products etc., pollution-preventing facilities for the preservation of production environments, and plant buildings. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing the technology for producing and degrading useful substances using bioconsortia, study was made of the handling technology of bioconsortia, the basic element technology, etc., and the FY 1999 results were reported. In the study of the high-grade utilization technology of lignocellulose/the components, an sample was obtained in which the effect of the bacteria culture supernatant treatment was recognized in the biobleaching by co-treatment of the bacteria culture filtrate - MnP. As to the search for control factor of lignin degrading enzyme and the utilization technology, it was found out that bisphenol A was efficiently degraded by a combination of laccase and mediator production bacteria. Concerning the utilization technology of plant symbiotic bacteria, classification/identification have been finished of approximately 60% of the stored bacteria. In the study of the production technology of the petroleum substituting useful resource, a system was constructed in which immature embryos were used for callus induction and regeneration of plantlets, and plants were regenerated at high frequency via the formation of adventitious embryos. By this, the culture cell with high propagation ability was obtained. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

Research and development of photovoltaic power system. Research on low temperature deposition of polycrystalline thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Teion seimaku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sato, K [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on a technology of low temperature deposition of polycrystalline thin films for solar cells. This research used ITO coated glass substrates, on which CdS was accumulated to a thickness of about 100 nm by using the CBD process, and over this deposition a CuInSe2 film was formed at 300{degree}C by using the ion cluster beam (ICB) process. The manufactured solar cells with a glass/ITO/CdS/CuInSe2/Au structure had an efficiency of 2%. In manufacturing a CuGaSe2 thin film by using the ICB process, effects of acceleration voltage relative to cluster beams and ionization current were investigated. It was found that the film morphology, the result of analysis by using X-ray diffraction, and the electric conductivity are sensitive to the ionization current. From these findings, an optimum film forming condition was derived. A CuGaSe2 thin film was manufactured by using the ICB process over a Cds thin film deposited by using the CDB process. Both of the surface morphology and X-ray diffraction patterns of the film did not show a large change, indicating a possibility of manufacturing cells with a reverse structure. Effects of heat treatment on CuInSe2 monocrystals were evaluated by using ESR and FTIR. 6 figs., 1 tab.

Report on the FY 1998 results of the New Sunshine Project (B version). Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In 1994, a memorandum on the research cooperation was agreed between NEDO and BPPT (The Agency for the Assessment and Application Technology) in Indonesia, based on the request for the coal liquefaction technology cooperation from BPPT. It includes the following items: conference for professionals to be held, invitation and training of Indonesian engineers, activity for joint field survey and potential survey of location of coal liquefaction commercial plant. Further in 1997, the secondary memorandum was concluded for the potential survey for securing the hydrogen required for coal liquefaction by coal gasification. The survey was summarized as the potential survey for location of coal liquefaction. In the testing study for improving economical efficiency of liquefaction process, it was made clear that the higher the Fe content of Banko coal is, the higher the reaction of liquefaction is, and that Fe compounds in coal show catalysis. In the Soroako area in Sulawesi island, there are the nickel mine run by PT. Inco. Soroako limonite is promising as catalyst material for commercial-scale coal liquefaction. In the gasification method, the plant construction cost increases, but the production amount of coal-derived liquid can be increased. That is more profitable than the production of hydrogen from natural gas. (NEDO)

`Technology for Advanced Treatment of High Melting Point Metal-Based Material,` local research and development of important technology for fiscal 1997. Development of materials creation technology for high efficiency power generator components; 1997 nendo juyo chiiki gijutsu kenkyu kaihatsu. `Koyuten kinzokukei buzai no kodo kako gijutsu` (kokoritsu hatsuden`yo buzai sosei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Efforts are made for the creation of high melting point metal-base materials to replace the currently-used Ni-base superalloys for the turbine to withstand higher operating temperatures. The main efforts made in fiscal 1997 are outlined. As in fiscal 1996, Nb-base solution alloys, in which solution reinforcement elements such as Mo and W are alloyed, are manufactured by button arc melting and tested for mechanical properties and texture/characteristics. In the designing and evaluation for a strongest Nb-base composite material, Nb-base composite materials are manufactured by use of particle dispersion-strengthening attained by addition of intermetallic compounds or elements to contribute to the formation of oxides, carbides, or nitrides. Nb-base composite materials may also be manufactured by use of eutectic-strengthening attained by utilizing crystallization in the process of coagulation. The resultant Nb-base composite materials are evaluated for their dynamic characteristics at high temperatures. In the development and evaluation of technologies for creating Nb-base materials for high-temperature components, larger specimens as heavy as several kg are tested in line with small specimens for basic studies, and the results are utilized for alloy designing for high-temperature materials. 50 refs., 97 figs., 15 tabs.

Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Technological development of hot rock power generation system - development of elementary technologies); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to identify the possibility of a hot rock power generation system, technological R and D has been performed on structuring of a man-made hydrothermal system, fracture mapping, downhole measurement and a circulating extraction system. This paper summarizes the achievements in fiscal 2000. With regard to the long-term circulating extraction test, a circulating heat extraction and test device was installed at the hot rock experimental field in the Hijiori area in Yamagata Prefecture, where geochemical data collection and tests including analyses thereon have begun. In reservoir bed analysis, a well module was incorporated into a reservoir bed simulator to improve the module so that comparison with the data of actual production on the ground can be performed. For the fracture mapping, AE having been observed during the long-term circulation test was analyzed, whereas it was estimated that the seismic source would not move or expanded during this period. A PTS logging has been performed during the long-term circulation test to investigate characteristics of the flow-out zone of the injection well and the production zone of the production well. In making the fracture model, an initial model was fabricated to estimate heat extraction behavior in the long-term circulation test. (NEDO)

Report on New Sunshine Program-supported undertakings for fiscal 1995. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported are the results of researches conducted in fiscal 1995. For the formulation of a general development design, data are collected about domestic high-temperature thermal wells through questionnaires and literature probing, and are scrutinized. As for the development of logging technology, a memory type PT (Pressure, Temperature) logger is experimentally constructed, and is found to properly operate in an environment of up to 350degC in a production well. An experimentally manufactured S-probe proves to be capable of heat insulation and sealing. In the field of PT monitoring, a high-temperature optical fiber is experimentally fabricated for study, capable of measuring temperatures up to 400degC. As for the development of high-temperature tracer monitoring technology, basic experiments are conducted about the thermal characteristics of aromatic acids, and preparatory experiments about gas phase tracers. In the study of scale monitoring technology, deep-seated fluids are collected and analyzed. In the field of production control, technical problems are discussed and information is gathered centering on methods for scale prevention and removal. 31 refs., 90 figs., 40 tabs.

Report on New Sunshine Program-supported undertakings for fiscal 1997. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu, shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Reported are the results of researches conducted in fiscal 1997. In the field of PTSD (Pressure, Temperature, Spinner flowmeter, fluid Density) well logging, the high-temperature performance of a memory type PT (Pressure, Temperature) well logger is confirmed in a demonstration test. As for the S-probe, modification is effected for the reduction of the outside diameter from 70mm to 56mm, and tests are conducted in real wells. As for the D-probe, a laboratory test is conducted and then the probe behaves as predicted. In the field of PCT (Pressure, Chemical, Temperature) monitoring, the sampler is subjected to an on-site test in Italy, when water is successfully sampled out of the well. In the field of scale monitoring technique, deep-seated fluid is collected and examined, and the scale deposition rate in the deep-seated fluid is determine. For the study of production control technology with respect to scale prevention and removal, an Mg-Si scale synthesis test is conducted in the temperature range of 100-300degC, and it is found that the solubility of scale decreases with a rise in temperature. 19 refs., 93 figs., 24 tabs.

Achievement report on industrial science and technology research and development in fiscal 2000. Research and development of synergy ceramics (Research and development of technology to prevent corrosion in petroleum production systems); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Achievements in fiscal 2000 were put into order for research and development of synergy ceramics aimed at completion of high temperature energy materials and ultra-precision materials. Activities were taken in the following four areas: 1) materialization technologies and advanced assessment and design technologies, 2) application technologies, 3) common basic technologies, and 4) assessment on composite function manifestation process. In Item 1), discussions were given on ultra-precision materials, high temperature energy materials, member designing basic technologies, materials to detect stress and microfine destruction, pore pattern controlling porous materials, and self-restoration and self-lubrication functioning materials. In Item 2), discussions were given on material and light selection functioning materials, high abrasion resistant and easy-to-process materials, high performance resistance materials for electric power devices, and flexible sliding materials. In the material and light selection functioning materials, their material selecting function was manifested by controlling micro pores through xerogelation on inorganic and organic hybrids. In the assessment of the composite function manifesting process, the wet type forming process was assessed, that uses microfine powder for model parts assuming cut members. (NEDO)

Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Development of silicon substrate manufacturing technology for high-quality solar cell); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Kohinshitsu taiyodenchiyou silicon kiban seizo gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for enhancing productivity and energy conservation by rendering continuous and automatic the electromagnetic casting process for manufacturing polycrystalline silicon substrates for solar cells. In the manufacture of ingots for substrates by continuous electromagnetic casting, the chuck type system for feeding power to the melt plasma was replaced by a roller type system, and the power feeding position was moved to the high temperature region. Also, an on-line ingot slicing technique was established. In the manufacture of substrates at a slicing rate of 300 {mu}m/minute, productivity of 115,000 wafers/month, yield of 98%, and thickness tolerance of 30 {mu}m were achieved. A high-speed cleaning technique was developed using a jet stream, by which the cleaning time was reduced to 5 minutes and the slurry recovery rate was elevated to 95%. Based on these, substrate-related costs in the case of 100 MW/year production was calculated, which resulted in a cost of 98.8 yen/wafer (target: 103.3 yen/wafer) for manufacturing 15 cm square substrates from ingots and in a 15 cm square substrate slicing and cleaning cost of 135.1 yen/wafer (target: 135.4 yen/wafer). (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - Development of production technology of thin film solar cells. Development of production technology of application type new structure thin film solar cells (Development of production technology of high efficiency hybrid thin films/sheet solar cells); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Oyogata shinkozo hakumaku taiyodenchi no seizo gijutsu kaihatsu, (Kokoritsu hybrid gata hakumaku / sheet taiyodenchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of realizing low cost and high efficiency hybrid thin films/sheet solar cells, the R and D were carried out, and the FY 2000 results were reported. As to the formation technology of the upper cell, the following technologies were developed and the results contributory to the heightening of efficiency were obtained: technology for improvement of cell characteristics by gap widening of p layer, technology for optimization of formation conditions of i layer corresponding to the hybrid solar cell, technology for heightening of current by the intermediate ZnO layer just under the upper cell. Relating to the development of formation technology of high quality microcrystal thin films, it was indicated that the microcrystal silicon thin film had the conformity effective also for polycrystal silicon, and at the same time, the conversion efficiency of 12.8% and release voltage of 0.579V were obtained by the cell using the cast polycrystal board. In the thin film/polycrystal sheet hybrid solar cell in which all these technologies were integrated, the conversion efficiency of 12.0% was achieved, and the possibility was verified of achieving the target efficiency of 14% by further improvement of FF. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - Development of production technology of thin film solar cells. Development of production technology of low-cost/large-area modules (Development of production technology of application type new structure thin film solar cells/Development of production technology of amorphous silicon-thin film polycrystal silicon hybrid thin film solar cells); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Oyogata shinkozo hakumaku taiyodenchi no seizo gijutsu kaihatsu, Amorufasusilicon hakumaku takessho silicon hybrid hakumaku taiyodenchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of developing the application type new structure thin film solar cell that is low-cost, high-efficient and practical, a developmental study was made of production technology of amorphous silicon/thin film polycrystal silicon hybrid thin film solar cells, and the FY 2000 results were reported. In the study of the heightening of efficiency of the small area hybrid cell, a structure was adopted in which a transparent intermediate layer was installed between a-Si cell and bottom poly-Si cell, and the initial efficiency of 14.0% was obtained in the small area cell 1cm square. As to the large area hybrid module, the initial efficiency of 11.7% and maximum output of 44.9W were achieved in the large area substrate module with a size of 910 x 455mm. In the indoor/outdoor evaluation of the output of hybrid modules, conducted were the outdoor measurement and the output measurement made every season under the mock spectral light in two-light simulator. In summer, F.F. was improved by spectral gain and anneal effect, and the effective output about 8% higher was recognized in the module after stabilization. (NEDO)

Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of complex biosystem analyzing technology; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The aim is to utilize the sophisticated functions of complex biosystems. In the research and development of technologies for effectively utilizing unexploited resources and substances such as seeweeds and algae, seaweeds are added to seawater to turn into a microbial suspension after the passage of two weeks, the suspension is next scattered on a carageenan culture medium, and then carageenan decomposing microbes are obtained. In the research and development of technologies for utilizing microbe/fauna-flora complex systems, technologies for exploring and analyzing microbes are studied. For this purpose, 48 kinds of sponges and 300 kinds of bacteria symbiotic with the sponges are sampled in Malaysia. Out of them, 15 exhibit enzyme inhibition and Artemia salina lethality activities. In the development of technologies for analyzing the functions of microbes engaged in the production of useful resources and substances for animals and plants, 150 kinds of micro-algae are subjected to screening using protease and chitinase inhibiting activities as the indexes, and it is found that an extract of Isochrysis galbana displays an intense inhibitory activity. The alga is cultured in quantities, the active component is isolated from 20g of dried alga, and its constitution is determined. (NEDO)

Research and development achievement report for fiscal 1998 on accelerated type biological function construction technologies. Development of new-type advanced-function enzyme creating technologies; 1998 nendo kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu seika hokokusho. Shingata kokino koso sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An artificial mutation/selection system was constructed in a laboratory based on molecular-level findings collected about the biological evolution mechanism, and biotechnology was studied for creating excellent biological functions. In the study of novel mutation generating technologies, selection is performed after the formation of numerous chimera enzymes by a family shuffling process using resistance to heat as the index. Then, a hybrid enzyme with its resistance to heat more than 10 times higher than that of the parent enzyme was obtained. In the study of establishing coordination between genotype and phenotype, a highly sensitive bacterial coordination technology was developed, and a highly sensitive detection method was constructed using a flow cytometer. As for technologies of highly efficient selection, a research was conducted about the selection of catalytic antibodies equipped with protease and esterase activity. In the study of technologies for enhancing adaptive walk in an evolution experimenting system, the usefulness is studied of a terrain survey based on the adaptive walk theory and a high-efficiency adaptive walk method using the mutation scrambling method. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Tandem type solar cells are developed, in which solar cells with different band gaps are stacked for effectively utilizing optical energy across the entire range of solar spectrum. A material gas supply control device for multiple epitaxial growth was added to a large-area GaAs film epitaxial growth unit, and a film thickness homogeneity of {+-}1% was achieved. A GaInP epitaxial layer fabricated in the same way was also enhanced in homogeneity. A low-carrier concentration layer was inserted into the top cell GaInP p-n junction for the construction of a p-i-n structure, and this improved on the short-circuit current. Furthermore, a p-p-i-n structure was constructed having two emitter layers, and this improved on spectral sensitivity for the achievement of a conversion efficiency of 13.6%. Studies were conducted about the tunnel junction which plays an important role in the stacking of cells, and the tunnel peak current was increased to 7.41A/cm{sup 2}. Fabrication is now under way of a GaInP/GaAs stacked cell, which is expected to exhibit a conversion efficiency of 25% or higher. In the case of a GaInAs cell to serve as the bottom cell, a conversion efficiency of 5.1% was achieved. Consequently, it is safely expected that a 3-junction stack of GaInP/GaAs//GaInAs will exhibit a conversion efficiency of 30% or higher. (NEDO)

Report on achievements in fiscal 1998. Development of a waste disposal and recycle related technology. (Development of a technology to dispose of air bags adequately); 1998 nendo haikibutsu shori recycle kanren gijutsu kaihatsu air bag tekisei shori gijutsu no kaihatsu nado seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-01

This technological development is intended to develop a process technology to dispose adequately of air bags convergently when they are removed from waste cars, with consideration paid on environmental and safety aspects. This technology that can dispose of air bags remaining as air bag modules (ABM) in large quantity and adequately can solve the problems of maloperation in opening them in cars and noise in conventional disposal methods. The recovery and disposal system using an inflator can be expected of reducing work load on dismantling contractors and enhancing the work safety. Furthermore, the energy saving process utilizing combustion of plastics can save resources. However, this technology has not elucidated how dioxins, dust, smoke, sulfides, and nitrogen oxides are generated and how the generation can be prevented. Therefore, an exhaust gas dioxin testing facility and an exhaust gas treating facility were installed additionally to the existing heating treatment facility to develop a disposal technology to treat adequately the exhaust gases generated when ABMs are disposed conveergently in large quantity, and treat the waste water discharged from the facilities. Fiscal 1998 has performed preliminary tests to accumulate fundamental data, and design and installation of the above two facilities. (NEDO)

Achievement report on developing coal liquefaction technologies in fiscal 1999 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant); 1999 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1999. In the disassembling study, wear, corrosion, and wall thickness change were investigated, and non-destructive inspection was performed on the major four facilities, and such newly developed devices as the liquefying catalyst manufacturing facilities, the slurry heat exchanger, and the let-down valves. The sampled test pieces were investigated of changes in the mechanical properties by means of the metallic structure inspection, hardness test, tensile test, and impact test. Deposits in the devices were investigated of their depositing conditions and constituents. The result reveals that the 3 Cr-1Mo-1/4V-Ti-B steel developed for the high-temperature, high-pressure, and hydrogen environment of the coal liquefaction plant showed excellent low-temperature tenacity and maintained good characteristics. No problems were discovered in corrosion resistance if PP using materials are used. The slurry handling centrifugal pump and instrumentation vales were worn out severely requiring replacements during the operation, for which further discussions are desired to be given. (NEDO)

Report on research achievements in fiscal 1999. Research and development of an ultra-high density electron SI technology (development of a technology for energy use rationalization); 1999 nendo chokomitsudo denshi SI gijutsu no kenkyu kaihatsu energy shiyo gorika gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

A high-density information network society is going to be realized in the 21st century. Information communication devices used therein are demanded of having high speed and high performance including acoustic and image digital processing, reduced size and weight, and low electric power consumption. While explosion in increase is estimated in the quantity of information handled by these information communication devices, there is a trend that the speed increase in CPU cannot follow the quantity increase. The present proposal is intended to make drastic performance enhancement by using the electron SI (comprehensive mounting) technology which includes making the LSI chips three dimensional and compounding light and electric power mounting, as well as design optimization. The present research and development has an objective to integrate the following three elements to achieve an ultra-high density electron SI technology: (1) a three-dimensional lamination technology making shortest wiring between LSI chips possible, (2) a light and electric power compounded mounting technology making high speed and large capacity transmission inside a board possible, and (3) optimal wiring structure design to suppress unnecessary electromagnetic radiation caused by increasing signal speeds. The research plan period lasts for five years. This paper reports the progresses in each theme in fiscal 1999. (NEDO)

Report on the achievements in fiscal 1999. Research and development on a basic technology to apply superconductivity (Research and development on a basic technology to apply superconductivity); 1999 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Chodendo oyo kiban gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

The development of a basic technology to improve superconductivity characteristics has performed (1) studies on the high-temperature superconductivity mechanism, (2) studies on the critical current mechanism, and (3) search for materials. In Item (1), composition and temperature dependence were investigated by measuring superconductivity gap and change in the electron state of pseudo gap using photo-electron spectra and Raman scattering spectra. In Item (2), magnetic flux behavior in the vicinity of the irreversible line was investigated on magnetic flux dynamics of Bi2212 by measuring magnetic resistance and magnetization. High viscosity condition having strong magnetic flux liquid zone was discovered. In Item (3), Sr was used in place of Ba as the constituting element, and several new mercury-based superconductors were synthesized successfully by using the high pressure synthesizing method. In developing superconductive bulk materials and wire materials, elucidation was given on (1) an element technology for high magnetic power bulk materials, (2) an element technology for high critical temperature bulk materials, (3) a fundamental technology for manufacturing next generation wire materials, (4) a fundamental technology for manufacturing next generation large current conductors, and (5) growth mechanism in wire material crystals. Development of laminating and processing technologies for superconductive materials has worked on (1) a single crystal substrate technology, (2) a thin film lamination technology, (3) a standard bonding technology, (4) an advanced bonding technology, and (5) a thin film and bond evaluation technology. (NEDO)

FY 2000 report on the results of the R and D of 'frontier carbon technology.' Development of the technology to rationalize energy utilization; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

This report summarized the FY 2000 results. In Chapter 1, development of electrically high functional diamond process technology, electric characteristics which frontier carbon materials have were made clear by the following four subjects, and the development was executed of original production process technology for realizing energy saving by heightening efficiency of electric devices, displays, etc. 1) development of morphology control; 2) development of technology to control electron emission characteristics; 3) development of technology to control oriented growth; 4) development of technology to enlarge single crystals. In Chapter 2, the basement technology of electron emission control was studied. Namely, conditions for film formation were investigated to elucidate the formation mechanism of carbon nano structure films by Dual RF CVD method, IPC CVD method and thermal CVD method. As to the electron emission mechanism of diamond, electron emission characteristics were outlined of the boron dope diamond thin film formed by micro wave plasma CVD method in FY 1999. In Chapter 3, investigational study of original production process technology of electrically high function materials, test study was made of the element technology needed to make high quality/large area diamond substrates. (NEDO)

Summary of the achievements in fiscal 1991 in developing the coal liquefaction technology and the bituminous coal liquefaction technology. Studies by using a pilot plant; 1991 nendo sekitan ekika gijutsu kaihatsu rekiseitan ekika gijutsu no kaihatsu seika gaiyo. Pilot plant ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-08-01

This paper describes the achievements in 1991 on studies on the bituminous coal liquefaction technology using a pilot plant. Based on the detailed design of the 150-t/d pilot plant, study problems and analysis items were reviewed, and a material balance acquiring method and a reaction column data analyzing method were discussed. Utilization of the liquefaction simulator was attempted. Efficient execution of the pilot plant operation study requires to have the basic and support study achievements reflected on the pilot plant operation, and clarify the roles to be played by the groups. Therefore, discussion items were compiled. The overall process plan for the design and construction was reviewed based on the plan discussed in fiscal 1990. Fiscal 1991 has launched common civil engineering constructions. The operation plans for the main four facilities in the pilot plant, which have been prepared in fiscal 1988, were continued of reviewing to cope with the situation of the decreased construction budget. The budget was reviewed again in fiscal 1991, which would present a prospect of starting the operation in fiscal 1995. Annual reviews on the basic operation plans for the main four facilities and the conceptions taken to date were put into order. The project management system was also expanded and re-arranged, including the information registration and retrieval system. (NEDO)

Achievement report for fiscal 1998 on the development of super-metal technology. Development of technology of high corrosion-resistance iron base controlled microstructure materials; 1998 nendo super metal no gijutsu kaihatsu. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

During ultrafine structure formation due to transformation from austenite to ferrite in an intense magnetic field, the transformation is accelerated by the thermodynamic stabilization of the ferrite phase which is ferromagnetic. The application of an intense magnetic field works effectively during the generation of nuclei. When a magnetic field is applied during reverse transformation, a honeycomb 2-phase structure is formed oriented toward the direction of the magnetic field and, when the structure is vertically compressed, the recrystallized structure is made ultrafine effectively. In pearlite transformation, hardening occurs when carbon atoms supersaturated in density are introduced in the presence of a magnetic field gradient, and curing further promotes precipitation hardening. In a ferrite complex phase system, wherein ultrafine globular cementite is uniformly distributed, plastic instability becomes explicit in a tensile test. There is a good possibility that an ultrafine structure recrystallization model may be built by calculation, into which the distribution of energy stored prior to recrystallizing nucleus formation is incorporated. The profile of a conceptual process of off-line or in-line integration of heavy-strain process and intense magnetic field application has become tangible. (NEDO)

NEDO Forum 2001. Session on industrial technology development (Future of thing making and manufacturing/processing technologies); NEDO Forum 2001. Sangyo gijutsu kaihatsu session (monozukuri seisan kako gijutsu no mirai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-20

The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. In a lecture entitled 'History of thing making,' the roles played by the now-defunct National Testing Laboratory and Industrial Test and Research Center were described and strategy for future development was predicted. In a lecture entitled 'Thing making and international apprentices competition,' apprenticeship training in practice at Denso Systems Corporation was presented. In a lecture entitled 'Key technology in thing making: outlook of metal mold industry,' shift in Japanese manufacturers' paradigm and change in metal mold marketing were explained, and the importance of reaching for the first position in the world in some specific fields or of expanding the scope of work in the entire value chain was stressed. In a lecture entitled 'Digital meister project: Aiming at amalgamation of IT (information technology) and MT (manufacturing technology),' database construction in the manufacture of metal molds, introduction of knowledge management systems, and development of CAD/CAM/CAE (computer-aided design/computer-aided manufacturing/computer-aided engineering) were discussed. (NEDO)

Report of high efficiency waste power generation technology development in 1995; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (1995 nendo hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

High temperature and high pressure steam has been investigated for the high efficiency waste power generation technology development. The steam temperature below 300 centigrade is currently employed to avoid the corrosion of superheater, and the generating efficiency is less than 15%. Practical application of 500 centigrade and 100 kg/cm{sup 2} is planned by developing corrosion resistance materials. Environmental load reduction technology has been also developed. For the external circulation type fluidized bed furnace combustion tests using dummy waste in fiscal 1995, the temperature control at bag filter was effective for suppressing the dioxins. When using waste plastics, HCl could be reduced by blowing Ca compounds. Various Cr-Ni-Mo-based alloys have been developed as a corrosion resistance superheater tube material, and are currently tested. For the environmental load reduction technology, the development of pulse plasma exhaust gas treatment method has been continued from fiscal 1993. In fiscal 1995, this method was confirmed using a small-scale test unit, and also tested using a 5000 Nm{sup 3}/h bench-scale unit. The removal rates of dioxins at the outlet of bag filter were 99.8% and 99.3%, respectively. They were found to be affected greatly by the pulse waveform. 13 refs., 107 figs., 24 tabs.

NEDO Forum 2001. Session on advanced power generation and storage technology development; NEDO Forum 2001. Shindenryoku gijutsu kaihatsu session

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-20

The presentations made at the above-named session and remarks made at the panel discussion of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Predicted by Deputy Chairman Tanaka of International Superconductivity Technology Center in his lecture entitled 'Energy problem in IT (information technology) oriented society' were that possibilities were high that power consumption would rapidly increase in line with the progress of broad band and wireless, that energy conservation and environmental technologies should be developed urgently, and that superconductivity technology would assume an important role. Discussed at the panel on 'Prospect of distributed power sources in power systems' were 'Power utilization by information communication in IT-oriented days and needs for development,' 'Energy utilization involving buildings and needs for development,' 'Tasks to discharge in cogeneration technology development and coordination with power systems,' 'Technical problems involving interconnection of distributed power sources and needs for development,' 'Present state of distributed power sources and needs for development,' and 'From Fuel and Storage Technology Development Department to Advanced Power Generation and Storage Technology Development Department.' (NEDO)

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of manufacturing technologies for low-cost substrates (low-cost Si sheets by continuous casting method); Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Tei cost kiban seizo gijutsu kaihatsu (renzoku cast ho ni yoru tei cost Si kiban seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on manufacturing of low-cost Si substrates by continuous casting method in fiscal 1994. (1) On manufacturing of ingots of 16 piece size, the ingot of nearly 170kg was manufactured by batch process using the Si melt injection unit prepared in last year. (2) On oxygen and carbon contents in wafers, the contents were measured by FT-IR after slicing of the ingot. As a result, the oxygen and carbon contents could be successfully reduced to the targets of 10ppma and 5ppma or less, respectively. (3) The resistivity distribution of the ingot ranged over the target of 1-2ohm-cm. (4) Cells of 100 {times} 100mm{sup 2} wide and 350{mu}m thick were verified by in-house evaluation process. Although lower cell conversion efficiency was found at the center top of the ingot, a vertical efficiency stability was nearly sufficient as a whole. (5) On the crystal growth unit prepared in fiscal 1994, any problems were not found on automatic driving and vibration during moving. 8 figs.

Industrial science and technology research and development institutions in fiscal 2000. Research and development of human media (Report on achievements in research and development of high-level information system for petroleum plant); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido. Human media no kenkyu kaihatsu seika hokokusho (sekiyu plant kodo johoka system gijutsu kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Having selected a petroleum refining plant as a large and complex system, a system was developed, that is capable of operating safely and efficiently a plant even by young operators by utilizing the human media technology that realizes information environment having a sense of unity with humans. With this system, if an anomaly is detected in the plant condition, the agent and the operator talk with each other freely, and necessary items of information are displayed on a large screen from moment to moment according to the priority thereof. Activities were taken in the following nine areas: 1) the total system, 2) research on an interface agent, 3) research on hypothetic plant indication interface, 4) research on a discrete cooperative treatment technology, 5) research on plant models and interface systems, 6) research on plant ontology, 7) research on significance indication interface, 8) improvement of tools to structure a large-screen integrated indication system, and 9) investigations on technological trends in foreign countries. (NEDO)

Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths (Development of technology to produce geothermal resources in great depths); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to develop geothermal resources, research and development has been performed on the production technologies for the deep-seated geothermal resources, such as pressure, temperature, flow speed and density (PTSD) logging technologies. This paper summarizes the achievements in fiscal 1999. In the actual well test on the developed D-probe, it was verified that the probe operates normally under high temperature environment (342 degrees C) which exceeds the measurement limit of conductive cables (315 degrees C). In developing the PTC monitoring technology, the downhole sampler was improved, and a test was performed in the actual hole in the Hijiori area in Yamagata Prefecture. As a result, collection of hot water of about 900 mL has become possible. In developing the high-temperature tracer monitoring technology, simulation was performed keeping in mind charging the tracer into the Hijiori geothermal area, whereas specifications for charging and collecting the tracer were determined. In developing the scale monitoring technology, experiments were carried out on the fluid systems under deep geothermal conditions by using scale forming devices, by which it was indicated that silica is the important scale constituent. (NEDO)

Fiscal 1997 report on the results of the R and D of industrial scientific technology. R and D of synergistic ceramics (R and D of corrosion prevention technology for the petroleum production system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To heighten durability and safety of materials/parts for undersea oil drilling, the development of ceramic base materials was made by developing function harmony type process technology which harmonizes on a high grade contrary characteristics and various functions. The paper summed up the fiscal 1997 results. In the design of system formation, computational simulation technology was developed to the composite process and the diploid system. The development of multifunction simultaneous manifestation materials was trially made by the higher nano structure process. A study was made of control of microstructures of porous materials and matrix filling by the gas phase precipitation control. Proposed were selective control of grain growth from species crystals and the columnar particle orientation laminated structure of simultaneous manifestation of strength and toughness. By composite precipitation reaction control, studied were simultaneous dispersion of whisker and increase in density of matrixes, and harmonization with long fibers. Silicon nitride was trially made with low lubrication/friction coefficients and high strength. A simulation method for crack progress behavior evaluation was developed using a testing notched specimen heterogeneous microstructures. Analyses were made of brittle fracture mechanics and reliability evaluation. 273 refs., 344 figs., 29 tabs.

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 4. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (Shiryo 4). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elements, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include instrumentation-related drawings covering an instrumentation loop sketch, instrument inspection specifications (flow meter, level gage, pressure gage, thermometer, regulation meter, analyzing meter, signal receiving meter, and instrument board), general specifications for electrical instrumentation facilities, etc. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 5. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 5). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elementary matters, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include engineering specifications related to electrical designs, lists of electrical items, specifications related to civil engineering designs, drawings such as planning drawings, and a detailed construction design drawn by an Australian engineering corporation and related documents and drawings. Concerning the manufacture of mechanical systems, items procurable in Japan, specifications of items procurable in Australia, lists, drawings, etc., are shown. Also included are the details of on-site preparation for construction and on-site work, conceptual designs of processes of dehydration, deashing, and secondary hydrogenation, etc. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 5. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 5). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elementary matters, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include engineering specifications related to electrical designs, lists of electrical items, specifications related to civil engineering designs, drawings such as planning drawings, and a detailed construction design drawn by an Australian engineering corporation and related documents and drawings. Concerning the manufacture of mechanical systems, items procurable in Japan, specifications of items procurable in Australia, lists, drawings, etc., are shown. Also included are the details of on-site preparation for construction and on-site work, conceptual designs of processes of dehydration, deashing, and secondary hydrogenation, etc. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 4. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (Shiryo 4). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elements, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include instrumentation-related drawings covering an instrumentation loop sketch, instrument inspection specifications (flow meter, level gage, pressure gage, thermometer, regulation meter, analyzing meter, signal receiving meter, and instrument board), general specifications for electrical instrumentation facilities, etc. (NEDO)

Report on achievements in fiscal 1998. Development of useful substance production technology utilizing gene combination technology; 1998 nendo idenshi kumikae gijutsu wo riyoshita yuyo busshitsu seisan gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In developing a useful substance producing technology utilizing gene combination technology, plants are taken as a kind of useful substance producing arena, wherein useful protein genes of animals are introduced and manifested in the plants. Thereupon, technological development was carried out for the following items with regard to mass production of useful substances that can be utilized industrially, such as cytokine, by means of plant and cell cultivation: 1. Development of a useful substance producing technology utilizing gene combination technology, and 2. Comprehensive surveys and researches. For the technology to obtain and design useful substance producing genes originated from animals, development of a technology to search and acquire useful genes originated from animals, and a design and modification technology for useful genes. For the technology to introduce genes into gene combined plants, creation of plants combined with useful substance producing genes, and development of an introduction technology using plant virus vector. For the technology to produce high-function chemical substances in the gene combined plants, establishment of technologies for mass breeding and activity analysis of gene combined plants and cultivated cells, and for extraction and refinement of useful substances from the gene combined plants. In the comprehensive surveys and researches, technologies were surveyed and items of information were collected inside and outside the country. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology - Separate volume: Collection of data of photovoltaic power generation systems); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu - Bessatsu: taiyoko hatsuden system data shu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the establishment of technologies for optimum designs and optimum operation for various types of photovoltaic power systems, data are compiled in this volume, collected from the field test facilities and residential photovoltaic power systems. Operating data and meteorological data from the field test facilities (interconnection system, independent system, and water pump system) are arranged as easy-to-use supplementary data to help studies in relation to the 'energy flow in the test field facility systems' which is in the fiscal 1999 achievement report. As for data collected from residential photovoltaic power systems, they are arranged as easy-to-use supplementary data to help studies in relation to the 'Data and evaluation of residential photovoltaic power systems' which again belongs in the fiscal 1999 achievement report. (NEDO)

Report on achievements in fiscal 1999 on research and development of immediately effective and innovative energy environment technology. Part 1. Development of immediately effective and high-efficiency solar cells, and development of technology to slice and manufacture thin-type large-area polycrystalline substrates; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (usugata daimenseki takessho kiban slice seizo gijutsu kaihatsu 1)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective of decreasing silicon usage quantity for the purpose of reducing the solar cell production cost, development is being performed on an ingot cutting technology to cut a silicon ingot to Kerf loss of 150 {mu} m and thickness of 150 {mu} m, and in which the produced wafers can withstand the cell making. Investigations revealed that a wire saw is suitable as the cutting system, and the wire used must have a diameter of less than 120 {mu} m, and a strength of more than 3850 N/mm{sup 2}. A prototype wire was fabricated, whose diameter is 120 {mu} m, and in which the strength is distributed between 3870 and 4110 N/mm{sup 2}. It was found possible that a wire of 160 {mu} m can be used to slice an ingot having a cross section surface of 150 mm square and a length of 300 mm into a slice having a Kerf loss of 200 {mu} m and a thickness of 180 {mu} m. This wafer had the in-plane distribution of the substrate thickness at {+-} 12.5 {mu}, swell of 120 {mu} at maximum, and surface roughness of 5 {mu}. Making ten of these wafers into a cell resulted in a yield of 60%. Assignments are the clarification of the properties of the cutting wire, the preparation of a thin wire with homogeneous quality, and the establishment of a technology to cut Kerf loss of 150 {mu} and substrate thickness of 150 {mu}. (NEDO)

Fiscal 1997 report on the R and D project consignment from NEDO on industrial science and technology. R and D on total base technology for marine resources (Mn nodules mining system) (total system (experimental plan)); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho (total system (jikken keikaku) hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Study was made on the design of experiments for confirming the technological and economical feasibility of commercial production of Mn nodules. An experimental sea area was selected considering Mn nodule characteristics such as concentration, continuity of nodule distribution and nodule size, and sea bottom topographic features such as flatness and exposed bed rock disturbing traveling of nodule collectors. The experimental plan was decided on the basis of the survey and study on an experimental scale, various requirements, weather and sea weather features of the sea area, and sea bottom conditions. Based on the experimental plan, various verification tests and simulation analyses were carried out, and functions of various equipment were confirmed. The conceptual design of a mining system assumed both pump-lift and air-lift systems, and yearly production rates of 2 and 3 million tons by 2 mining barges, and summarized main points of every system. As the evaluation result, the future direction of commercial production of Mn nodules was clarified to a certain extent. 5 figs., 21 tabs.

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

Report on development of high-efficiency wastes power generation technology in fiscal 1998. 1. Development of component technology, and demonstration test of a pilot plant; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Yoso gijutsu kaihatsu (pilot plant jissho shiken) (dai 1 bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A technology is developed to perform high-efficiency power generation by generating high-temperature and high-pressure steam stably by burning general wastes and combustible industrial wastes as fuel. This paper describes summary of the achievements in fiscal 1998. Corrosion tests were performed on over-heater materials under steam condition of 500 degrees C and 100 kg/cm{sup 2} by using a hot model. It was verified by the tests that the corrosion environment around an external heat exchanger is milder than that with an external stack. A circulation fluid bed was simulated from operation data, and a prospect was obtained on steam conditions required for the high-efficiency power generation. In order to elucidate the corrosion mechanism, discussions were given on deposited ash properties, corrosion characteristics and stress. Elucidation was made on a discharge chamber structure most suitable for removing dioxins and NOx by using a waste gas treatment process that uses plasma generated by discharge. A concept design was made. The economic effect of the system is equivalent to that of the activated carbon blow-in process, whereas a waste gas treatment system was nearly completed. As a result of the pilot plant test, the power generation efficiency is estimated to be 30% in a scale of 1200 tons per 24 hours. A demonstration test revealed that dioxin emission was far below the regulation value. An optimal system was also discussed. (NEDO)

Achievement report on research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a recombinant DNA utilizing technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research in fiscal 1981 on the 'research and development of a recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. For the method to create energy saving type bacteria stocks for processes centering around the escherichia coli, refinement was carried out on cytochrome P-450 and NADPH-cytochrome P-450 reduction enzyme respectively from hepatic microsome of rats administered with induction agents. Attempts were made to prepare antibodies working on them. For the method to create high-efficiency secreting bacteria stocks centering around bacillus subtilis, activity measurement and quantification were performed on enzymes external to the bacillus sutilis, and research was executed on introduction of neutral protease gene sensitive to bacillus subtilis temperatures into the NA20-S17 stock. For the method to create bacteria stocks to substitute raw materials used in the chemical industry, studies were performed on separation of enzymes and corresponding genes, and incorporation of the genes into the escherichia coli. In the comprehensive investigation and research on the recombinant DNA utilizing technology, information exchange and discussions meetings were held, and investigations were made on literatures and patents. (NEDO)

Survey report for fiscal 1993 on development of coal and brown coal liquefaction technologies. Part 2. Survey of economic efficiency of brown coal liquefaction process; 1993 nendo sekitan ekika gijutsu kaihatsu kattan ekika gijutsu no kaihatsu chosa hokokusho. 2. Kattan ekika process no keizaisei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Financial assessment is carried out by estimating the liquefaction product cost (selling price) at which the predetermined rate of return on investment is to be earned, which is calculated by the DCF (discount cash flow) method. The cash flow is determined from the net after taxes for each business year, and the balance after the subtraction of long- and short-term borrowings is converted to the present worth as of the operation commencement year at the predetermined discount rate, and a total is calculated for the period. When the difference between the total and the equity does not vanish, the coal liquid selling price is changed, and this process is repeated until the difference vanishes. If a 20% reduction in the plant construction cost is feasible, the coal liquefaction product will be competing with the crude oil in the market in around 2030. Although the financial analysis is a profitability analysis from the fund providers' viewpoint, the benefit as seen from the project siting country needs to be assessed by an economic analysis, and probabilities are that, in the presence of great profits, the project will materialize if the two are found to earn more than average after the profits are impartially divided. Japan's benefits and expenditures are compared and subjected to an economic analysis, and a result of 6-15% is obtained. This means that the project will realize in case EIRR (economic internal rate of return) is higher than the fund procuring cost of 11%. (NEDO)

FY 1999 report on the result for research and development of instantaneously effective and innovative energy and environment technology. Development of technology to use combustible wastes as resources and fuels; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu kanengomi saishigen nenryoka gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Manufacturing compressed fuel, or refuse paper and plastic fuel (RPF) from combustible wastes such as used papers and waste plastics to utilize them effectively as a fuel to substitute fossil fuels is regarded as a promising engagement. However, this process indispensably requires removal of chlorine contained in used papers and waste plastics to a degree that they do not impede the combustion. The present research and development is intended to develop a PRF pretreatment technology and a dechlorination technology, and establish a technology to utilize the materials as resources and fuels as thermal recycling of combustible wastes. The current fiscal year has performed research and development on the following themes: development of a sorting system and a crushing system in developing the pretreatment technology, whereas for the former system, sorting tests were carried out by using a vibration type wind power sorting machine and an inertia force wind power sorting machine, and for the latter system, data were obtained on the crushing characteristics; dechlorination tests, in which it was discovered that the mixing ratio of used paper in the material affects the chlorine concentration; research on combustion characteristics, in which fundamental combustion tests using a small fluidized bed, combustion tests using a bench scale fluidized bed, and stoker fired furnace combustion tests were performed; and demonstrative operation researches. (NEDO)

Achievement report on research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a recombinant DNA utilizing technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research in fiscal 1981 on the 'research and development of a recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. For the method to create energy saving type bacteria stocks for processes centering around the escherichia coli, refinement was carried out on cytochrome P-450 and NADPH-cytochrome P-450 reduction enzyme respectively from hepatic microsome of rats administered with induction agents. Attempts were made to prepare antibodies working on them. For the method to create high-efficiency secreting bacteria stocks centering around bacillus subtilis, activity measurement and quantification were performed on enzymes external to the bacillus sutilis, and research was executed on introduction of neutral protease gene sensitive to bacillus subtilis temperatures into the NA20-S17 stock. For the method to create bacteria stocks to substitute raw materials used in the chemical industry, studies were performed on separation of enzymes and corresponding genes, and incorporation of the genes into the escherichia coli. In the comprehensive investigation and research on the recombinant DNA utilizing technology, information exchange and discussions meetings were held, and investigations were made on literatures and patents. (NEDO)

FY 1999 report on the results of the development of recycling technology of waste architectural materials, glass, etc. Development of the simple glass coloring/decoloring technology; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kan'igata glass chakudasshoku gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of increasing the ratio of recycling of waste architectural materials, glass, etc., the development was proceeded with of easy coloring of colorless glass by light irradiation and decoloring of it by heat treatment. The important point for technical development is to develop glass materials which are colored by light and decolored by heat at a level of technique with practicality and to develop coloring/decoloring device. Studies were made in the following three fields: 1) optimization of coloring/decoloring conditions for coloring/decoloring occurring from defects (color centers) under light irradiation; 2) optimization of coloring/decoloring conditions occurring from colorless ions and particulate formation under light irradiation; 3) development of a visible drawing device. In 1), bottle, sheet glass, and soda-lime silicate glass are colored brown by X-ray/UV radiation, but the coloring is bad in stability. However, it was found that the addition of silver oxide improved stability. In 2), it was recognized that when the glass containing a trace of Mn was melted in the reducing atmosphere, it became colorless, and when radiated by X-ray and heat-treated at approximately 200 degrees C, it was colored bluish violet which was vivid and stable. (NEDO)

Achievement report for fiscal 1996 on the research and development of technologies for important region. Development of control system technology for combustion with energy use rationalized, etc.; 1996 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The goal is to develop basic technologies to build an SiC device capable of service amid high-temperature surroundings for the advancement and optimization of combustion control systems. In an SiC semiconductor, the Si-C bond is broken when irradiated with ions, and this makes the occurrence of thermal oxidation easy to occur. In the study to form SiC into single-crystal substrates, a substrate with warpage of 10 micrometers or less and surface coarseness of 10 nanometers or less is realized. In the development of sensor technologies, the high-speed CVD (chemical vapor deposition) method is applied for the growth of crystals further on a 3C-SiC layer epitaxially grown by MBE (molecular beam epitaxy) surface control, which improves on layer characteristics. Element technologies are developed for the construction of a 3-terminal element (FET: field effect transistor), which is for the construction of a high-temperature, high-speed SiC device. An effort is made at achieving 3C-SiC hetero-epitaxial growth, etc., on a 3-inch Si substrate using an SiC crystal film formation experimenting apparatus, which aims at constructing a control device. Concerning the combustion control system, the relations between the air/fuel ratio and the emission spectra of radicals OH, CH, and C2 in a flame are made clear. Also referred to are the basic studies being conducted at research institutes such as universities and a survey of technological trends abroad.

Fiscal 1997 research report on development of use technology of bio-resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho (fukugo seibutsukei riyo seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report summarizes the fiscal 1997 research results on production technology of functional materials, and the research study result for utilizing substance production and decomposition by complex biosystem for industries. For detecting technique of microorganisms in soil, staining by CFDA-AM was suitable, and allowed visualization of sulfate- reducing bacteria during culture. For research on functional analysis technology, study was made on atomic force microscope technology to detect microorganisms in environment and observe their fine structures. For research on detection, separation and cultivation technology of difficult-to-culture microorganisms, a molecular genetic analysis method of microbial communities and a determination method of their viability were selected. For functional substance production technology, study was made on technical utilization of bioflocculant produced by microbial consortia as environment-friendly oil removal reagent, and on gene transfer control in microbial consortia. For the research study for the project, survey was made on useful substances produced by complex biosystem. (NEDO)

Survey report for fiscal 1993 on development of coal and brown coal liquefaction technologies. Part 2. Survey of economic efficiency of brown coal liquefaction process; 1993 nendo sekitan ekika gijutsu kaihatsu kattan ekika gijutsu no kaihatsu chosa hokokusho. 2. Kattan ekika process no keizaisei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Financial assessment is carried out by estimating the liquefaction product cost (selling price) at which the predetermined rate of return on investment is to be earned, which is calculated by the DCF (discount cash flow) method. The cash flow is determined from the net after taxes for each business year, and the balance after the subtraction of long- and short-term borrowings is converted to the present worth as of the operation commencement year at the predetermined discount rate, and a total is calculated for the period. When the difference between the total and the equity does not vanish, the coal liquid selling price is changed, and this process is repeated until the difference vanishes. If a 20% reduction in the plant construction cost is feasible, the coal liquefaction product will be competing with the crude oil in the market in around 2030. Although the financial analysis is a profitability analysis from the fund providers' viewpoint, the benefit as seen from the project siting country needs to be assessed by an economic analysis, and probabilities are that, in the presence of great profits, the project will materialize if the two are found to earn more than average after the profits are impartially divided. Japan's benefits and expenditures are compared and subjected to an economic analysis, and a result of 6-15% is obtained. This means that the project will realize in case EIRR (economic internal rate of return) is higher than the fund procuring cost of 11%. (NEDO)

Report on the research and development under a consignment from NEDO of high temperature carbon dioxide fixation and utilization technology for fiscal 1996; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku gyomu seika hokokusho. Nisanka tanso koon bunri kaishu sairiyo gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the prevention of global warming, this R and D is aimed at separating/recovering high temperature CO2 from high temperature gas at 300degC or above and developing technology for effective use of the recovered CO2 as measures taken for reduction in CO2 emissions from the fixed emission sources. In this fiscal year, the following were proceeded with: heightening of separation performance evaluation technology, promotion of technical development of ceramic separation membranes and supports, and development of element technology of modular integration. In the examinational research on separation technology and system optimization, the following were conducted: survey of trends of the technical development, conceptual design of plant and prediction of process behavior, assessment of applicability of the process, and study of effects of utilization/spread of the developmental technology. In the former R and D, borosilicate glass powder rich in alkali is formed on the ring by joining the trially manufactured hollow fiber type membrane and the same form alumina cylinder, and sealing property and strength which stand measurement of permeability were confirmed. In the latter, an innovative process applied with CO2 high temperature separation technology was studied to examine effects of the spread of high temperature gas separation technology. 403 refs., 478 figs., 134 tabs.

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a voluminous cell incubation technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Saibo tairyo baiyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research and development in fiscal 1981 on the 'voluminous cell incubation technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. In the research of a method for producing industrial materials using cells originated from lymph-based trunk cells, researches were performed on selection and breeding of cells, development of serum-free media, and establishment of the optimal culture method with regard to the method for producing industrial materials using stocks producing virus induced interferon. Regarding the method for producing industrial materials using idio-interferon producing mutable stocks, research and development was made on selection and breeding of superior cell stocks and serum-free media. With regard to the method for producing industrial materials using marrow originated cells, such researches were carried out as technological investigations, collection of cells, establishment of the proliferating condition for myeloid leukemia cells, discussions on the assay method for differentiation inducing factors, and search for cells producing useful substances. Other activities include research of the method for producing industrial materials using cells originated from epithelium cells, information exchange on voluminous cell incubation technologies, and investigations on literatures and patents. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology; 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Efforts are made to develop a GaInP/GaAs-based compound semiconductor solar cell built on an Si substrate, the Si substrate being lower in cost, higher in mechanical strength, lighter in weight, and higher in heat conductivity than a GaAs or Ge substrate. Fiscal 1999 studies involved improvement on GaAs/Si heteroepitaxial growth and the evaluation of crystallinity in thus grown layers, improvement on cell characteristics, fabrication and evaluation of an n{sup +}/p structure cell, and so forth. As for crystal growing technologies, a 980 degree C 5-heat-cycle annealing method was applied, and the density of dislocation was reduced to 5 times 10{sup 6}cm{sup -2}. In the fabrication of cells, an n{sup +}/p structure cell was studied, and the cell achieved 12.5mAcm{sup -2} in short-circuit photoelectric current over 9mAcm{sup -2} of the conventional p{sup +}/n structure GaInP cell. Without any special effort to optimize the structure, a GaInP/GaAs layer-built cell on a GaAs substrate achieved 23.7% in conversion efficiency. When it is taken into consideration that conversion efficiency on an Si substrate is approximately 80% of what is achieved on a GaAs substrate, it is deemed that the achievement of 23.7% suggests that near 20% in conversion efficiency may become available on an Si substrate. (NEDO)

FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the consortium based analysis technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made to look for the consortium based analysis technology by which the consortium base can be analyzed as it is using the molecular biological method. Studies were made in the following four fields: 1) new identification technology of eucaryote using II DNA topoisomerase genes (PCR amplification method of II DNA topoisomerase genes); 2) method to detect new recognition peptide activated microorganism (adjustment of cortical antigen); 3) technology to elucidate detection/response mechanism of the specific environment and adaptation/resistance mechanism of the specific environment; 4) incubation method inside 3D matrices. In 3), studies were made of the analysis of inhibition mechanism of korormicin and separation of solvent-resistant oil degradable bacteria. In 4), for the settlement and dynamic analysis of microorganism consortium by studying incubation conditions, conducted was the molecular system analysis of bacteria and eumycetes inhabiting in sponge. (NEDO)

FY 1998 annual summary report on manipulation of atomic and molecular extremes. Development of technologies for high-efficiency analysis/manipulation of DNA and the like; 1998 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to establish the techniques for observation/manipulation of atoms and molecules, as the common basic techniques for various industrial areas, e.g., new materials, electronics, biotechnology and chemical. Development of atomic field and scanning tunneling microscopes working under extreme conditions has been pursued, in order to manipulate complex systems, such as living body. For identification of molecular species, laser-excited fluorescence is combined with scanning mechanical probing to further refine the single molecule detection/identification techniques, and the objectives are set to develop a new method for evaluating molecules in a living body using a scanning probe microscope, and also to develop a novel scanning probe microscope for molecules in a living body. The other efforts were directed to R and D of the techniques for observing structures of organic molecules and the like through the measurements of adsorption process of organic molecules and clusters on semiconductor substrates and their surface reactions, and precision measurements of vibrational conditions of adsorbed molecular species reacting in the solid-liquid interfaces by high-sensitivity Raman spectroscopy to elucidate the catalysis mechanisms at the molecular level. (NEDO)

Achievement report for fiscal 1987 on the entrusted research and development of basic technologies for next-generation industries. Research and development of technologies of mass culture of cells; 1987 nendo jisedai sangyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Saibo tairyo baiyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The aim is to add value to the chemical industry by establishing technologies for realizing a large and stable supply of fine chemical products whose industrial production is difficult when conventional techniques are applied, the products including various useful substances yielded by animal cells including those of man. To fulfill the aim, efforts are exerted to complete basic technologies involving the mass culture of cells through conducting researches into animal biofunctions. This report covers the endeavors made in fiscal 1987 under the above-named project created in fiscal 1981. All the subject matters are for the development of substance production methods for industrial use, and include the studies of use of optimal cultivation methods mainly for serumless cultures and cultivation engineering, studies centering on the high-density cultivation of cells and serumless cultures, studies using suspended and quasi-suspended cell lines, studies using cells deriving from bone marrow, and studies using epithelial cells. Furthermore, the results are outlined of the comprehensive researches conducted into technologies of mass cultivation of cells. (NEDO)

Fiscal 1994 report on results of R and D on new forming technology of composite materials. Development of innovative technology for producing members for high efficiency power generation; 1994 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Activities were conducted in the three areas of (1) R and D on ceramic matrix composite forming technology, (2) R and D on metallic matrix composite forming technology, and (3) comprehensive investigation and adjustment, for the purpose of developing materials that manifest superplasticity among ceramic and metallic matrix composites as well as developing the forming and fabrication technology and also of improving productivity by simplifying the fabrication processes. In (1), upon discovering that the superplastic properties of zirconia (3Y-ZrO{sub 2}) sold in the market is affected by the grain size and impurities (Al{sub 2}O{sub 3}) of the material, a zirconia was developed in which a trace of Al{sub 2}O{sub 3} and SiO{sub 2} were added, with a method detected capable of the fabrication through a low deforming stress. In (2), development was carried forward for a new high specific strength high-temperature material applicable to aircraft engines for example, as well as its forming and fabrication technology, by making a composite between metals and between metal and ceramics by a mechanical alloying (MA) method. Metalcarbide, nitride and oxide made by the MA method were sintered by hot press or the like, and a sintered material was thereby obtained that was superplastic and capable of the near net-shape forming. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1995. 2. Main subject (Part 1. Physiologic indexing technology); 1995 nendo ningen kankaku kesoku oyo gijutsu no kenkyu kaihatsu. 2. Honronhen (Seiri shihyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This paper describes the physiological indexing technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1995. In work stress evaluation using mainly autonomic nervous system indexes, factors for the work stresses were extracted and experimental environments were put in order in applying the technology to the indexing at higher levels and the coordinative works. Use of common primary indexes was introduced for transitory stress, and the common primary indexes were introduced also for chronic stress. In the stress evaluation using composite physiological function measurement, data analyses were made, and discussions were given on the time series basis on the action indexes and the physiological indexes as the work performance of a work load assigning work to elucidate points of the problems. In stress indexing using skin temperatures, a possibility was obtained in indexing by using the skin temperatures on transitory stresses during tension and monotonous work. Measurement of stresses with hormone placed as the main subject tries to apply to human being the changes in hormones which have been verified since quite some time ago by animal experiments. However, it is difficult to find a definite trend because of complexity of stresses in the human society. For the basic arousal indexing, studies were made on improvement of accuracy of the monitor and quantification of actions of physical stimulation. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 8) - development of hydrogen production technology; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 8. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

R and D was conducted with the view of establishing hydrogen production technology based on the solid high polymer electrolyte water electrolysis method, which presumably offers higher efficiency and lower cost than conventional methods. This year, as well as implementing development of large-scale cell lamination (electrode area 2,500 cm{sup 2}, 10 cells) by using two hydrogen production methods (electroless plating method and hot press method), work was started for developing cells (electrode area 1,000 cm{sup 2}) for hydrogen stations. In the research on longterm durability improvement, with a 50 cm{sup 2} membrane electrolyte or cell, the evaluation test results were obtained of stable electrolytic performance showing more than 93% energy efficiency after 400 hour operation, under the conditions with electrolysis pressure 0.4MPa and electrolysis temperature 120 degree C. In a test of 1,000 cm{sup 2} prototype cell for hydrogen stations, the evaluation result was obtained for energy efficiency of 92% under the conditions with electrolysis pressure 0.5MPa and electrolysis temperature 120 degree C; thus, this year's target efficiency of over 90% was achieved. Further, enhancement of the quality was contrived for example by improving the electroless plating method and remodeling a roll press machine. (NEDO)

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a voluminous cell incubation technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Saibo tairyo baiyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research and development in fiscal 1981 on the 'voluminous cell incubation technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. In the research of a method for producing industrial materials using cells originated from lymph-based trunk cells, researches were performed on selection and breeding of cells, development of serum-free media, and establishment of the optimal culture method with regard to the method for producing industrial materials using stocks producing virus induced interferon. Regarding the method for producing industrial materials using idio-interferon producing mutable stocks, research and development was made on selection and breeding of superior cell stocks and serum-free media. With regard to the method for producing industrial materials using marrow originated cells, such researches were carried out as technological investigations, collection of cells, establishment of the proliferating condition for myeloid leukemia cells, discussions on the assay method for differentiation inducing factors, and search for cells producing useful substances. Other activities include research of the method for producing industrial materials using cells originated from epithelium cells, information exchange on voluminous cell incubation technologies, and investigations on literatures and patents. (NEDO)

Fiscal 2000 report on results of R and D of industrial science and technology that creates new industry. Development of supermetal technology (development of technology for innovative metallic material); 2000 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of obtaining higher strength/toughness in metallic materials, R and D was conducted concerning nano-sized grain refining and bulk forming by micro-grain dispersion, with fiscal 2000 results compiled. In {gamma} stainless steel, development was conducted using SUS304 as the base material, revealing that ZrC was effective for forming a micro-crystallized grain structure. In addition, it was found feasible that precipitation behavior of carbide was controllable through a temperature rising process at the time of solidification forming. In an HIP+ (hot isostatic pressing) hot forged material with ZrC finely dispersed, it characteristically showed an average crystalline grain size of about 300 nm, a tensile strength of 1,085 MPa, and a Charpy impact value of 1.86 MJ/m{sup 2}. Further, in thin plates micro-crystallized by thermo-mechanical treatment using martensite reverse transformation, a strain rate sensitivity index m value became 0.3 or higher at a strain rate of 10{sup -2}S{sup -1}, indicating manifestation of superplasticity. In {sigma} stainless steel, TiO{sub 2} and ZrO{sub 2} were examined for their effect of suppressing grain growth on the basis of SUS410. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 4. Research and development of correlation and evaluation technology (Part 1); Ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The achievements during fiscal 1993 of research and development on a method to evaluate warm heat comfort by living scenes of workers by using a human body thermal model included completion of a human thermal model introduced with physiological knowledge such as artery-vein anastomosed (AVA) blood vessels and two-system blood circulation net. The effectiveness of the model was experimented and verified. It was made possible to estimate the reversal phenomenon occurring in hot heat environment, in which skin temperatures at peripheral body parts rise higher than those in the body trunk part, and skin temperature distribution. In the correlation study to estimate statistically the sense volume from skin temperatures, it was possible to estimate significantly different sense volumes from face skin temperatures, but the estimation accuracy was low because of such factors as difference in individuals. What is important in enhancing the accuracy is to identify ecological reactions of human being caused from change in the sense volume, select effective parameters, and study the mechanisms. In order to develop stress relaxing scents, discussions were given on degree of subjectivity stress by question papers and cortisol concentration in saliva as the parameters. An experimental system was developed to measure the effects of the scents to relax work stresses. A screening method was developed, whereas effects of 15 kinds of scent materials were investigated. (NEDO)

FY 1998 report on the results of the development of utilization technology of biological resources such as bioconsortia. Development of the bioconsortia system utilization/production technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of developing the industrial utilization technology, analysis was made of functions and interactions of the specified functional biological groups, and at the same time the developmental study was made of the technology to isolate/culture the constitutive biological groups. The FY 1998 results were summed up. As to the technology to detect microorganisms in soil, the SFDA method was improved and the new dyeing method was developed. And, there almost was hope for the development. Concerning the functional analysis technology, the functional substances peculiarly manifested only in the complex system in the ocean environment are searched. Several kinds of compounds were found out, and at the same time the test to confirm the biological activity is under way. Relating to the isolation/culture technology, study was made on rotten fruit, and the existence in the sample of the microorganisms which are difficult in isolation/culture was newly confirmed. In regard to the culture of the microorganisms which are difficult in isolation/culture, availability of the replica method was found out. As to the technology to produce functional substances, studies were made on the following: utilization technology of the environmental harmony type oil/water separation polymer producing microbial consortia, method to artificially make gene exchanges in the microbial consortia, etc. (NEDO)

1998 report on results of research and development on new venture type industrial science and technology. 'Technological development of super metal' (technological development of innovative metallic material); 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Results on 1998 research and development were summarized concerning the technological development of innovative metallic materials. In the research of particulate micro-diffusion technology, as a modeling of nano-structure holding process, Ag/Fe nano-crystal alloy was manufactured by inert gas vapor deposition, with the structural change at the time of rolling examined. In addition, a large-scale spark plasma sintering device was developed, with a 40mm diameter cylinder manufactured. In the research on crystal grain refining process by a stirring solidification method, crystal grain refining was achieved to 1{mu}m order. In the development of an advanced aluminum alloy forming method, concerning a high-speed superplastic molding technology, a basic evaluation test was carried out for the superplastic characteristics of rapidly solidified aluminum alloy continuously from fiscal 1997. Further, a calculator simulation was performed by the finite element method for the high-speed superplastic molding. From these results, knowledge was obtained necessary for the detailed design of a high-speed superplastic molding device. On the basis of this knowledge, manufacturing of the equipment was implemented, as were the introduction, rise, basic test, etc. (NEDO)

Project to aid development of an oil substituting fuel manufacturing technology in fiscal 1998. Report on the result of developing a technology to make cable covering materials into fuel; 1998 nendo sekiyu daitai nenryo seizo gijutsu kaihatsu hojo jigyo. Densen hifukuzai nenryoka gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research and development have been carried out with an objective to re-utilize waste cable covering materials as oil substituting energy. The research has been performed on behavior of chlorine and lead being substances that impede making the cable covering materials into fuel, development of a technology to remove chlorine, lead and copper, and pelletizing properties for fuel making. In the study of behavior of chlorine and lead, the following matters were made clear: dechlorination reaction completes within 30 minutes if pyrolysis temperature is higher than 300 degrees C; the more the amount of filler CaCO3 in test samples, the less the dechlorination amount; and secular deterioration does not affect the dechlorination amount. A technology has been developed successfully to remove the substances that hinder making the cover materials into fuel, achieving the target values of copper at 0.2% or less, lead at 0.3% or less, and chlorine at 5% or less. In developing the pelletizing technology that puts the cover materials into raw materials for blast furnaces, dechlorination rate of 90% was achieved by mixing coke/PVC at a ratio of 1/1 and dechlorinating it by using a rotary kiln. It was verified that the product is free of problems in particle size as the blast furnace raw material. (NEDO)

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1982. Research and development of a recombinant DNA utilizing technology; 1982 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Achievements were compiled on the research and development in fiscal 1982 on the 'recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. With regard to refined cytochrome P-450 molecular species, a material was obtained that has further higher specific content than those having been discovered in fiscal 1981. Refinement was carried out on antibodies against P-450 and NADPH-cytochrome P-450 reduction enzyme to raise the antibody values. Identification was made on the refined cytochrome P-450 molecular species. The P-450 in the mRNA products prepared in fiscal 1981 was quantified successfully by means of the immuno sedimentation process using protein A-sepharose. In fabrication of cytochrome P-450cDNA, detailed discussions were given on the cDNA fabrication and reaction conditions, where double-chain cDNA was obtained. In refining the enzymatic cytochrome P-450, discussions on culture conditions of the enzyme discovered a condition in which the P-450 content increases. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 4. Research and development of correlation and evaluation technology (Part 2); Ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Developments were performed during fiscal 1993 on a system to investigate correlation among external stimulating environment, physiological effects and sense volume based on a physiological reaction model. The development works included improvement of the model, discussions on a method to estimate parameters inside living organisms, and a method to collect subjectivity volume data. Prototypes thereof were fabricated, evaluated, and experimented, where nearly complete achievement of the targeted functions was verified. In developing a technology to evaluate quantitatively the comfort of composite environments composed mainly of warm heat environment, discussions were given on an integration evaluating expression in order not to make handling the environmental physical volume too complex. The expression models the evaluation of governing sense volume in individual environments of warm heat, light beam, and sound, and calculates the composite environment evaluation indexes by using the evaluation indexes obtained from the modeling as the descriptive variables. In developing the space-type human interface adapted to human senses, a computer system to realize the interface and the platform for function mounting were developed. The development items were broken down respectively on the basic technologies for functional aspect and surveillance and control function mounting, and the software systems. The human comfort meter achieved the basic design target. (NEDO)

Achievement report for fiscal 1998. Research and development of technologies for creating new bioaffinity molecules using submicron beads (Energy use rationalization related technology practicalization); 1998 nendo biryushi riyogata seitai ketsugo busshitsunado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the effort to develop chemical substance/bioreceptor analysis technology using submicron beads, polystyrene core/polyglycidyl methacrilate beads are used in a study started about a detachable spacer using newly developed fixation technology. In the development of bioaffinity chemical substance refining technology, two kinds of sugars and several kinds of aromatic aldehydes serve as building blocks in the construction of a library, and studies are made of analyses using liquid chromatography and mass spectrography. In the development of novel substance creation technology based on information on the analysis of chemical substance/bioreceptor, in an effort at developing technologies for creating novel function provided chemical substances, heterocyclic compounds, alkaloids, and sugar compounds are selected and their syntheses in the liquid phase and solid phase are studied, which is again for the construction of a library. (NEDO)

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1982. Research and development of a recombinant DNA utilizing technology; 1982 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Achievements were compiled on the research and development in fiscal 1982 on the 'recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. With regard to refined cytochrome P-450 molecular species, a material was obtained that has further higher specific content than those having been discovered in fiscal 1981. Refinement was carried out on antibodies against P-450 and NADPH-cytochrome P-450 reduction enzyme to raise the antibody values. Identification was made on the refined cytochrome P-450 molecular species. The P-450 in the mRNA products prepared in fiscal 1981 was quantified successfully by means of the immuno sedimentation process using protein A-sepharose. In fabrication of cytochrome P-450cDNA, detailed discussions were given on the cDNA fabrication and reaction conditions, where double-chain cDNA was obtained. In refining the enzymatic cytochrome P-450, discussions on culture conditions of the enzyme discovered a condition in which the P-450 content increases. (NEDO)

FY 1998 report on the results of the development of utilization technology of biological resources such as bioconsortia. Development of the bioconsortia system utilization/production technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the technology to use high grade functions of the bioconsortia system, the R and D were conducted, and the FY 1998 results were summed up. As to the study of functional material producing technology, screening of the 2400 strains owned by Marine Biotechnology Institute was conducted using reporter strain, and about 400 strains of homoserine lactone producing bacteria which are interbiological information convey substances were obtained. Concerning the effective decomposing/purifying technology of petroleum products, study of petroleum decomposition analysis technology was finished in the development of culture/control technology of petroleum decomposition microbial consortia constitutive bacteria. Relating to the analysis of the petroleum decomposition microbial consortia, changes in the bacteria population at the site of the heavy oil pollution accident on the Sea of Japan were investigated for the past one year by the PCR/DGGE method. It was found out that levels of the oil pollution in ocean could be assessed by measuring the concentration of Alcanivorax. As to the technology for highly utilizing unused petroleum fractions, conducted were the chemical analysis of photolytic crude oil, selection of the decomposition microbial consortia, etc. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of environmental technology such as recycling (for public). 1; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo). 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This R and D is aimed at promoting reduction in environmental loads by waste, etc. and reutilization of waste, etc., and at developing environmental technology such as recycling contributing to reducing road traffic noise. Studies were made on operation conditions of material separation in the bottle state and flake state, color separation, washing process, etc. Moreover, tests were conducted on comparisons of performance of shredders with different functions. Running tests of 100,000 times were conducted to confirm effectiveness of durability of the paved road with used papers. Measurement of hardness of the resin using the sol-gel method and coating experiment using organic dye were carried out to study the membrane effect speed and flaw resistance of coating of coloring bottles. Gasification of shredder dust and separation of nonferrous metal and glass were conducted to get the basic data. As to FRP bath tubs, the ratio of glass fiber and plastics was studied and western tiles were trially manufactured. Further studies were made of removal conditions of noncombustibles, chlorine and sulfur content, and reaction conditions of alkali additives including kind, quantity and addition method. 166 figs., 132 tabs.

Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-01

Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

Fiscal 1998 R and D report on femtosecond technology (ultra-short pulse optoelectronics technology); 1998 nendo femuto byo technology no kenkyu kaihatsu (chotan pulse hikari electronics gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report reports the result of the fiscal 1998 R and D on femtosecond technology supported by NEDO. For creation of industrial basic technologies supporting the advanced information society in the 21st century, ultra-high speed electronics technology including new functions beyond the speed limit of conventional electronics technologies is indispensable. From such viewpoint, this R and D aims at establishment of the basic technology necessary for ultra- high speed electronics technology through R and D of technology controlling conditions of beams and electrons in a femtosecond (10{sup -15}-10{sup -12} seconds) region. In fiscal 1998, this project first succeeded in fabrication of a prototype pulse compressor by using semiconductors, and developed a new pulse compressing method by using fibers to generate ultra-short pulse of 38fs. By developing new materials for intersubband transition where ultra-high speed responses can be expected, optical absorption by intersubband transition was first confirmed at optical communication wavelength. The main result for every theme is reported and explained. (NEDO)

Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

Research and development of peripheral technology for photovoltaic power systems. Research on engineering methods for cost effective PV installation; Shuhen gijutsu no kenkyu kaihatsu. Tashu secchi koho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of engineering methods for photovoltaic power system installation in fiscal 1994. (1) On the survey on applicable fields, various application aspects, applicability, and problems on location and legal regulation were continuously studied for railway, river reservation, lake surface and public facility as promising locations after highway in the last fiscal year. The result pointed out relatively easy possibility of PV power generation of nearly 11,700MW except residence and building fields. (2) On installation technology of solar cell arrays, several models based on various installation conditions, construction methods and system configurations were studied, and various application aspects were proposed by combination of simple design conditions. (3) On test and evaluation of the structural design of array racks, wind tunnel experiments were conducted for structure wall, platform shed and highway sound insulation wall. (4) On basic design of various promising systems, the conceptual design of interconnection systems was carried out assuming applications to highway and railway. 7 figs., 3 tabs.

FY 2000 research and development of fundamental technologies for AC superconducting power devices. R and D of fundamental technologies for superconducting power cables and faults current limiters, R and D of superconducting magnets for power applications, and study on the total systems and related subjects; 2000 nendo koryu chodendo denryoku kiki kiban gijutsu kenkyu kaihatsu seika hokokusho. Chodendo soden cable kiban gijutsu no kenkyu kaihatsu, chodendo genryuki kiban gijutsu no kenkyu kaihatsu, denryokuyo chodendo magnet no kenkyu kaihatsu, total system nado no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project for research and development of fundamental technologies for AC superconducting power devices has been started, and the FY 2000 results are reported. The R and D of fundamental technologies for superconducting power cables include grasping the mechanical characteristics associated with integration necessary for fabrication of large current capacity and long cables; development of barrier cable materials by various methods; and development of short insulated tubes as cooling technology for long superconducting cables, and grasping its thermal/mechanical characteristics. The R and D of faults current limiters include introduction of the unit for superconducting film fabrication, determination of the structures and layouts for large currents, and improvement of performance of each device for high voltages. R and D of superconducting magnets for power applications include grasping the fundamental characteristics of insulation at cryogenic temperature, completion of the insulation designs for high voltage/current lead bushing, and development of prototype sub-cooled nitrogen cooling unit for cooling each AC power device. Study on the total systems and related subjects include analysis for stabilization of the group model systems, to confirm improved voltage stability when the superconducting cable is in service. (NEDO)

Report on the FY 1998 results of the New Sunshine Project (B version). Data attached 2. Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo (fuzoku shiryo 2))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the project for internationalization of coal liquefaction technology, this paper reported on the potential survey for location of Indonesian low grade coal liquefaction (study of applicability of the improved BCL process and survey of hydrogen production technology using coal gasification). The survey was conducted of a locational possibility of a coal liquefaction commercial plant to be located at mine site in South Sumatra for Banko coal raw material. The improved BCL process was applied in which the results of the study by NBCL Takasago Research Institute were reflected. Further, the hydrogen production was studied by gasification of Banko coal, and the comparison was made with the conventional natural gas reforming method. As a result of the study using information/knowledge obtained during the conceptual design of Australian brown coal, the construction cost of commercial scale liquefaction plant with the Banko coal processing amount of 30,000 tons/day became 549.8 billion yen in the case of using natural gas as raw material for hydrogen production. This construction cost is the lowest as compared with 601.7 billion yen in the demonstrative BCL process and with 577.1 billion yen in the advanced BCL process. This is a process making use of features of Banko coal. The process for hydrogen production by the steam reforming method using natural gas has an advantage of increasing the production amount of coal-derived liquid the most of the three other methods. (NEDO)

Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (R and D of petroleum production system high-grade measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D were conducted of high-strength and high-accuracy welding/joining technology using laser, technology to measure and assess the joining state of structures and defects around the surface of structures and inside structures by high accuracy and high resolution, and technology/equipment to generate a laser light source for the tool, which are all required to remarkably enhance safety/reliability of oil drilling facilities working in the severe environment. In fiscal 1997, as the R and D of oil production system high-grade measuring/processing technology, technical study, study of measures to be taken, operating experiment, assessment, examination, etc. were conducted on the following themes: 1) macroscopic processing technology (R and D of high-reliability laser welding technology), 2) non-destructive composition measuring technology (R and D of internal measurement and photoelectron spectroscopy using short-wavelength radiation), 3) tight-focusing all-solid-state laser technology (R and D of fiber laser), 4) tight-focusing all-solid-state laser technology (R and D of high-efficiency laser diode), and 5) comprehensive investigation of phonics engineering (investigation for photon-applied materials processing technology). 256 refs., 205 figs., 18 tabs.

Report on the FY 1998 results of the New Sunshine Project (B version). Data attached 1. Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo (fuzoku shiryo-1))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the project for internationalization of coal liquefaction technology, this paper reported on the potential survey for location of Indonesian low grade coal liquefaction (study of applicability of the improved BCL process and survey of hydrogen production technology using coal gasification). The survey was conducted of a locational possibility of a coal liquefaction commercial plant to be located at mine site in South Sumatra for Banko coal raw material. The improved BCL process was applied in which the results of the study by NBCL Takasago Research Institute were reflected. Further, the hydrogen production was studied by gasification of Banko coal, and the comparison was made with the conventional natural gas reforming method. As a result of the study using information/knowledge obtained during the conceptual design of Australian brown coal, the construction cost of commercial scale liquefaction plant with the Banko coal processing amount of 30,000 tons/day became 549.8 billion yen in the case of using natural gas as raw material for hydrogen production. This construction cost is the lowest as compared with 601.7 billion yen in the demonstrative BCL process and with 577.1 billion yen in the advanced BCL process. This is a process making use of features of Banko coal. The process for hydrogen production by the steam reforming method using natural gas has an advantage of increasing the production amount of coal-derived liquid the most of the three other methods. (NEDO)

FY 1999 Report on research and development of energy utilization rationalization superhigh-technological liquid crystal technologies. Superhigh-technological electronic technology development promotion project for new functional electronic material design, control and analysis technologies; 1999 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-04-01

Described herein are the FY 1999 results of the liquid crystal technology development project. For the researches on multi-layer reflection, composite panels of flattened resins of different refractive index are developed to improve 2-layer monochromic contrast ratio. The guest/host liquid crystal compositions of high orientation order are investigated as the those useful for high contrast. Compounds are pursued for superanisotropic light absorption, and modification with a substituent is found to be effective. Molecular orientation controlling is also studied. For researches on memory-sustaining type liquid crystals, the studied items include formation of thin ferroelectric films on glass substrates, improvement of voltage-sustaining characteristics by composites (including compounds), and doping of trace quantities of ionic impurities. For development of image element colors, the studied items include multi-lattice-structured, oriented HPDLC devices, composites of high birefringence (high order light scattering), and light interference, high order light scattering type light control devices. The multi-dimensionally anisotropic structure of configuration divided into 3 parts of R, G and B is developed to create directive reflection which improves brightness of the reflection type color liquid crystal. A group of compounds are pursued to develop liquid crystal compositions of high refractive index anisotropy, and promising ones are found. The results of the comprehensive investigations are also described. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. Management of research and development (System development committee working group); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (system kaihatsu bukai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

This paper reports activities carried out in fiscal 1999 by the system development committee working group, a subordinate organization of the committee for development of the photovoltaic power generation technology. The items of implementation laid with emphasis in the current fiscal year included deliberations on the research achievements of the projects completed in fiscal 1999, on the research achievements of the new projects during fiscal 1999, and on pre-final evaluation of the development of a technology to put photovoltaic power generation system into practical use. The themes on the progresses in fiscal 1999 reported in March 2000 consisted of the followings: research and development of a system evaluation technology, investigation and research on supply capability evaluation on the photovoltaic power generation system, researches on peripheral devices for AC modules, investigation and research on electric safety of the photovoltaic power generation system, investigation and research on long-term reliability of inverters, investigation and research on meteorological data for optimal design, investigation and research on evaluation of the photovoltaic power generation, research on a photovoltaic power generating multi-hybrid system, research on a high-density linkage technology, and demonstrative research on a solar beam micro-hydraulic hybrid system. (NEDO)

NEDO Forum 2000. Geothermal technology development session (new development of geothermal energy); Chinetsu gijutsu kaihatsu session. Chinetsu energy no shintenkai

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The following themes were presented at this session: (1) geothermal development in the future, (2) the current status of geothermal development and utilization, (3) surveys on the promotion of geothermal development, and (4) verification and investigation on geothermal exploration technologies, development of hot water utilizing power generation plants, and international cooperation on geothermal development and utilization. In Item 2, report was made on the current status of geothermal power plants in Japan and their future development targets, long-term overview of geothermal development, measures and budgets to achieve the targets of geothermal development. In Item 3, it is reported that out of 48 areas completed of the survey (including the new promotion surveyed areas), the areas possible of steam power generation and confirmed of temperatures higher than 200 degrees C are 30 areas, and the areas possible of binary power generation (using down hole pumps) and small to medium scale power generation, confirmed of temperatures of 100 to 200 degrees C are 13 areas. In Item 4, reports were made on the reservoir bed variation exploring method, surveys on deep geothermal resources, a 10-MW demonstration plant, a system to detect well bottom information during excavation of geothermal wells, a technology to collect deep geothermal resources, and a hot-rock using power generation system. In Item 5, geothermal exploration in remote islands in the eastern part of Indonesia, and the IEA cooperation projects were reported. (NEDO)

FY1995 development of a novel rapid immunoassay technology; 1995 nendo shinkina kosoku men'eki sokutei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

By utilizing the phenomenon that the antigen induces association of VH and VL, which are the antigen-recognizing fragments of antibody, develop a novel rapid immunoassay technology which will eliminate the defects of conventional immunoassays, such as long measuring time and requirement of expensive large automated apparatus. In addition, develop a methodology to make Fvs with low VH-VL affinity but that associate tightly in the presence of antigen. Using a model anti-hen egg lysozyme antibody HyHEL-10 Fv and BlAcore, we have clarified the kinetic basis of the Fv stabilization by HEL. By labeling HyHEL-10 VH, VL with succinimide esters of fluorescein and tetramethylrhodamin, respectively, at their N-termini, we could successfully detect VH-VL association by the increment of fluorescence resonance energy transfer. As a result, 1 {mu} g/ml of antigen could be detected homogeneously in less than 5 minutes. Some VH-VL association measurement systems were made by utilizing M13 phage display of VH fragments of HyHEL-10, anti-nitrophenacetyl, anti-digoxin antibodies. (NEDO)

Report on the development/comprehensive research of new hydrogen energy demonstrative technology; Shinsuiso energy jissho gijutsu kaihatsu sogo kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

In this project, the excess heat phenomenon caused by electrolyzing heavy water using palladium metal, etc. as electrode was captured as `new hydrogen energy.` To make a possibility of being as a future energy source clear, the abnormal heating phenomenon was verified. By elucidating the mechanism, the paper aimed at quantitatively controlling the heat generation. The R and D period was four years from fiscal 1993, and the details of the research are about the excess heat measuring test, material analysis/development tests, test on detection of reaction products, information collection/arrangement, international research cooperation. As a result of the research, a part of the excess heat measurement was surely able to be reproduced. However, when a confirmation experiment on the excess heat was conducted by another more positive method under the same conditions, it was found that the excess heat quantity was not the absolute excess heat quantity exceeding the measuring sensitivity/errors of the system. Supposing the excess heat of 0.1W order is generated in nuclear reaction, any of reaction products should be detected in a considerable quantity. However, no reaction products were not detected. 42 refs., 241 figs., 55 tabs.

Execution management of batter piles and problems of technical development. Uchikomi kui no seko kanri to gijutsu kaihatsu no kadai

Energy Technology Data Exchange (ETDEWEB)

Ninomiya, Y [JDC Corp., Tokyo (Japan); Omori, H [Nippon Kokan Koji K.K., Yokohama (Japan)

1991-05-15

This report introduces the practical examples of the present system of execution manegement. Necessary functions and basic problems are described as well as the possibility of utilizing hydraulic/pneumatic pressure for the automation or the robotization which are the future technical problems. Application examples are also shown on the execution management system by means of an accelometer which was developed by the authors. This area is not long after the start of study. Essential points of the execution management of the batter piles are that the front tips of the piles are confirmed to be securely penetrated to the specified depth in the specific support layer giving the required supporting strength at the same time. For this purpose, what are required are to accurately measure the penetration displacement of the piles and assess the maximum penetration and final penetration and the amount of the rebound. Then the support strength should be checked from the dynamic support force. For this, it is required to develop an execution management system which is simple and adept for the operation at the spot. 9 refs., 12 figs., 5 tabs.

Basic research program for innovated coal utilization in Japan. BRAIN-C program; Sekitan riyo kiban gijutsu kaihatsu. BRAIN-C program

Energy Technology Data Exchange (ETDEWEB)

Harada, M [Center for Coal Utilization, Japan, Tokyo (Japan)

1996-09-01

This paper introduces the circumstances and purpose of establishing the Basic Research Associate for Innovated Coal Utilization (BRAIN-C) Program started in October 1995, and the summary of the results therefrom in fiscal 1995. Although development of coal utilization technologies has been implemented over a number of years, there are many problems still requiring solutions. Early realization has been urged on diversification of coal utilization, acceleration of technological development and diversification of coal types. In order to achieve these goals, the necessity was recognized afresh on not only the hardwares, but also on basic technologies in terms of software which can identify properties of coals, systematize different reactions, and estimate reactions, fluidity and heat transmission of coals. Therefore, receiving a subsidy from the Agency of Natural Resources and Energy of the Ministry of International Trade and Industry, a research and development program to be implemented jointly by industries, administrative agencies and academic societies had been started with a five-year plan for the time being. With the activities for the program such as collecting 50 to 100 types of coals and supplying them to researchers, the program had been accelerated in fiscal 1995 on a large number of themes and results therefrom, including fundamental properties and thermo-chemical reactions. 2 figs., 4 tabs.

Development of regeneration technique for diesel particulate filter made of porous metal; Kinzoku takotai DPF no saisei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yoro, K; Ban, S; Ooka, T; Saito, H; Oji, M; Nakajima, S; Okamoto, S [Sumitomo Electric Industries, Ltd., Osaka (Japan)

1997-10-01

We have developed the diesel particulate filter (DPF) in which porous metal is used for a filter because of its high thermal conductivity and a radiation heater is used for a regeneration device because of its uniform thermal distribution. In the case high trapping efficiency is required, filter thickness should be thick. The thicker filter has a disadvantage of difficulty in regeneration because of the thermal distribution in the direction of thickness. In order to improve regeneration efficiency, we designed the best filter-heater construction which achieves uniform thermal distribution by using computer simulation and we confirmed good regeneration efficiency in the experiment. 4 refs., 14 figs., 1 tab.

Development of novel processes for Cu concentrates without producing sulfuric acid; Hiryusan hasseigata no atarashii doshigen shori gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, T; Noguchi, F; Takasu, T; Ito, H [Kyushu Inst. of Technology, Kitakyushu (Japan). Faculty of Engineering

1997-02-01

In the refining process for the production of copper from pyrites, heat treatment is carried out in a neutral atmosphere so that part of the sulphur will be collected in the form of simple sulfur and that pyrites naturally low in reactivity will be made active. A basic study is also conducted of a very high speed electrolytic method. The chemical aspects of pyrites which are various in composition (mainly CuFeS2) are clarified by X-ray diffraction, and then is subjected to heat-treatment in a 773K-1073K argon atmosphere. There is a decrease in the amount of sulfur at a temperatures not lower than 973K. The X-ray main diffraction line splits for the emergence of some lower angle diffraction lines. The specimen is then subjected to a leach test in a copper chloride base liquor, to disclose that leachability grows remarkably higher in the presence of a great change in the X-ray diffraction lattice constant. An experiment follows in which an electrolyte is allowed to flow at a high speed for accelerating the rate of electrolytic refining in an effort to prevent the passivation of anode and deposition of dendrite on the cathode that is apt to occur when the current density is high. Passivation is prevented when the flow rate is 10m/min or higher in the vicinity of the anode surface for the formation of a smooth electrodeposited surface. 2 refs., 2 figs., 2 tabs.

Development of novel processes for Cu concentrates without producing sulfuric acid; Hiryusan hasseigata no atarashii doshigen shori gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Awakura, Y; Hirato, T [Kyoto University, Kyoto (Japan)

1997-02-01

Studies are conducted to develop a new wet method for copper concentrates to replace the conventional dry smelting method for the settlement of problems involving the processing of impurities for environmental protection. A specimen of pyrites polycrystals is subjected to leaching at 80 {degree}C in a strongly acidic cupric solution. Findings are that the element sulfur generated in this process does not impede leaching and only approximately 4% of the sulfur is oxidized into sulfur ions; that the presence of more than 2g/liter of bromide ions produced during bromine-aid leaching of gold changes the structure of sulfur for the inhibition of leaching; that circulation of a bromine-containing leaching liquid is not desired since even a small amount of approximately 0.02mol/liter inhibits the leaching rate. Controlled potential electrolysis is performed for the anode in an acid solution containing CuCl, NaCl, and NaBr, for the observation of oxidation/reduction potentials predicted by Nernst`s equation. It is then disclosed that bromine is more effective than chlorine in gold leaching and that the solution potential during leaching agent regeneration enables the monitoring of solution constitution. 2 refs.

Fiscal 1999 research achievement report on the development of SNPs related technologies; 1999 nendo SNPs kanren gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop specimen processing technologies for modifying and enabling various kinds of specimens to automatically undergo SNP (single nucleotide polymorphism) analysis for medicine development and clinical diagnostic activities and to develop technologies and apparatuses to enable rapid, inexpensive, and simple search and analysis of SNPs using DNA (deoxyribonucleic acid) chips and mass spectrometry. Activities are conducted in the four fields involving (1) the development of a practical clinical system for rapid detection and analysis of SNPs, (2) research and development of an SNP scoring system using bar-coded oligonucleotides and magnetic beads, (3) research and development of a high-speed SNP analysis system using a mass spectrometer, and (4) the development of a high throughput SNP analysis line. Efforts exerted in field (1) involve a protein fixation method using plasma polymerization and its application to DNA arrays, development of an SNP detection method using human genomes, construction of a rapid DNA detection device using an electric field, development of an SNP analysis system using the solid phase HPA (hybridization protection assay) method, and SNP analysis using solid phase ligation. (NEDO)

Present situation of technical development to cope with CO sub 2 exhaust. CO sub 2 taisaku gijutsu kaihatsu no genjo

Energy Technology Data Exchange (ETDEWEB)

Sema, T [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

1991-04-01

A quantitative evaluation was made on techniques of CO{sub 2} immobilization utilizing organisms by referring to literatures. The techniques used for the evaluation were the following six ones: The first one is to plant trees on wastelands located in the tropics and the subtropics and CO{sub 2} is immobilized by grown trees. The second one is to compulsorily blow CO{sub 2} into water to immobilize CO{sub 2} by multiplicated microorganisms such as green algae. The third one is to multipulicate phytoplanktons by spraying deficient trace elements on oceans where trace elements such as Fe are deficient in spite of rich nutritive salts to absorb and immobilize CO{sub 2}in seawater. The fourth one is to multipulicate shellfishes in coastal regions to immobilize CO{sub 2} in seawater as their shells. The fifth one is to multipulicate many coral reefs in tropic or subtropic coastal regions to immobilize CO{sub 2} as calcium carbonate. The sixth one is to multipulicate large size seaseeds such as giant kelps in shallow seawaters to immobilize CO{sub 2} in seawater. The width of each applicabe area, immibilizingcapability of CO{sub 2} and the executing cost were considered to evaluate respective methods. As a result, the multipulication of marine planktons were thought most promising. 1 fig., 4 tabs.

Report on results concerning development of supermetal technology, R and D of offshore oil production supporting system, and development of technology for aluminum-based high-anticorrosive microstructured metallic material (FY2000); Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kaitei sekiyu seisan shien system kenkyu kaihatsu (Aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of developing high strength and high-anticorrosive aluminum-based material through microstructure control, R and D was conducted, with fiscal 2000 results compiled. In the research of grain refinement mechanism, molten metal rolled stock was experimentally produced in which Mg content was varied 0-2.5 mass % with Al-2.5 mass % Mn as its base. As a result, a microstructure with an average grain size of about 3 {mu}m was obtained by processing the alloy through homogenization at 550 degrees C, cold rolling by 91% and the final treatment at 350 degrees C without Mg addition. Addition of Mg increased square grain boundaries in the microstructure, raising proof stress to about 180 MPa in Al-2.5%Mn-2.5%Mg alloy. In the research of development of the machining process, a rapid heating process was performed on a typical aluminum alloy, with the effect examined, by an alloy system or a plate thickness, on the electric power used and on the temperature reached. A rapidly heated aluminum alloy plate turned to have a microstructure with equi-axed grains of a uniform size, compared with a salt bath processed material heated at the same temperature. (NEDO)

Results of the supplementary work to the fiscal 1994 New Sunshine Project. Development of geothermal power plants, etc. (development of production, technology for deep-seated geothermal resources); 1994 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant to kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu shinbu chinetsu shigen seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper reports on the fiscal 1994 results of the study of the development of a technology for collecting deep-seated geothermal resources, which has been made for increasing the capacity of the geothermal power generation as a part of the New Sunshine Project. As a plan for the development, a development is made of logging equipment and its auxiliary system and then characteristics of the deep-seated geothermal well are clarified. The logging equipment is a PTSD (pressure/temperature/spinner flow-meter/fluid density) logger which stands the use at deep-seated geothermal wells of 400{degree}C and 490 kgf/cm{sup 2} and measures pressure, temperature, flow rate and fluid density under static and dynamic conditions. In this fiscal year, metal seals were developed for preventing geothermal fluids from penetrating into the PT probe. Qualities and inner/outer diameters of various kinds of structural materials used in the S probe were determined, and output necessary enough to detect the rotation number is obtained. Measuring precision of D logging by {gamma} rays was evaluated. The study was made of the monitoring technology including the borehole and ground measuring system, the borehole fluid sampling and the scale formation. Relating to the tracer widely used in monitoring of hydrothermal reservoirs, investigated was the trend of the technology from abroad. 8 refs., 60 figs., 26 tabs.

Fiscal 1997 report on the results of the introductory R and D of the New Sunshine Project under a consignment from NEDO. Introductory R and D of the supercritical fluid use technology; 1997 nendo `New Sunshine keikaku` sendo kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D of chemical reaction using supercritical fluids started in fiscal 1997. In the R and D of solvent reaction, as the research on polymer decomposition with supercritical water, studies were conducted of the mechanism of conversion reaction to chemical materials, cleavage mechanism of stable chemical bonds, and synthetic reaction in the supercritical state reaction field. In the research on oxidation reaction, as the study of complete oxidation in supercritical water for high efficiency energy recovery, studies of complete oxidation of liquid fuels, and complete oxidation of solid fuels. In the research on hydrogenation, studies of lightening of heavy oil in supercritical water, etc. In the R and D of the basic technology, studies of corrosion mechanism of metals in supercritical water, construction of the basic framework for technical database of supercritical fluids, etc. In the survey of technical trends and new research themes, the introductory R and D of element technology, etc. were conducted, and the results were described of the survey of technical trends and new research themes and the trend survey of overseas technology. 314 refs., 87 figs., 81 tabs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research, development, and survey of crystalline solar cell evaluation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (kesshokei taiyo denchi hyoka system no kenkyu kaihatsu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the basic study of ultrahigh-efficiency cells, the technology of ribbon crystal growing is again attracting attention for shortage of Si material supply. The new technology and problems to solve for cost reduction for it are discussed. Concerning the bulk type crystalline Si which is a core material, recent trends are mentioned involving studies of basic substrate properties such as the photoabsorption coefficient and crystal defects for achieving higher efficiency, development of gettering and surface passivation technologies, enhancement of processing speeds, radiation concentration behavior, etc. Newly obtained findings about photodegradation are mentioned, and some remedial measures are described. Recent reports on the application of porous Si to solar cells are compiled. In connection with the development of low-cost quantity-production process technologies, a remarkable progress recently marked by polycrystalline Si solar cells is described. Furthermore, it is stated that new process technologies will be required in the fields of material refining, substrate manufacturing, and cell fabrication. A proposition is presented aiming at developing cell modules compatible with application systems and practicalizing modules that may be integrated with roofing materials. Reference is also made to surveys overseas. (NEDO)

Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of high- efficiency production process technology); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on R and D of laser processing technology, in-situ measurement technology, and generation and control technology of photon as laser beam source, for energy saving and efficiency improvement of energy-consumptive production processes such as welding, jointing, surface treatment and fine particle fabrication. The research was carried out by a technical center, 9 companies and a university as contract research. The research themes are as follows: (1) Processing technology: simulation technology for laser welding phenomena, synthesis technology for quantum dot functional structures, and fabrication technology for functional composite materials, (2) In-situ measurement technology: fine particle element and size measurement technology, (3) All- solid state laser technology: efficient rod type LD-pumping laser module, pumping chamber of slab type laser, improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology, fabrication technology for nonlinear crystals, and high-efficiency harmonic generation technology. Comprehensive survey was also made on high- efficiency photon generation technologies. (NEDO)

Fiscal 1999 achievement report on research and development of industrial technologies. Research and development of synergy ceramics; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are conducted in the two fields of (1) survey and research and (2) development of technology for evaluating high temperature dynamic corrosion characteristics of heat resistant ceramics. In field (1), a comprehensive survey is conducted, an application study is conducted about high temperature gas separating ceramic membranes, and efforts are made to put to practical use ceramic parts manufactured by a low cost production process. In the application study of ceramic membranes, technologies are developed for a process of manufacturing high temperature gas separating porous ceramic membranes capable of separating and purifying gas emissions and gas ingredients, which involves the development of technologies for improving on gas separation and purification functions, development of technology of providing catalyst support function, technology of porous membrane formation, evaluation of separation characteristics, and so forth. In an application study for ceramic parts manufactured by a low cost manufacturing process, which involves structural ceramics, optimization is accomplished for materials synthesizing technologies by means of mechanical alloying, and cylinder liners are fabricated and evaluated for a natural gas engine made of silicon nitride based ceramics. In field (2), a high temperature dynamic corrosion testing device is built for heat shield coatings. (NEDO)

Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

Load leveling air conditioning technology development by unused energy high-level utilization. Summary of achievements by development themes; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu kaihatsu. Kaihatsu temabetsu seika gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

This paper introduces a number of research and development cases on utilization of unutilized energies. In developing the component technology for a thermal plant utilizing low-temperature unutilized energies, the paper introduces a heat exchanger system to collect heat from sea water, a heat exchanger system to collect heat from waste heated area in subways and urban sewage plants, and a high-density heat transportation system using ice plus water slurry or PCM-C plus water slurry. Furthermore, with regard to the heat pump system using low-temperature unutilized hear sources, development was introduced on a 'heat source load responsive heat pump system', which combines a load variation responsive heat pump utilizing river waters with a latent heat storage system using nighttime electric power serving for electric power load leveling. In developing the component technology for a heat plant utilizing high-temperature unutilized energies, introduction was given on a turbine driven turbo type heat pump system, a high-efficiency absorption type heat pump, a waste heat driven absorption type freezer, and an urban type underground heat storage tank. (NEDO)

Research and development of utilization technology of solar thermal system for industrial and other use. Development of passive solar system (research and development of advanced glazing); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Passive solar system no kaihatsu (chokozai nado no kenkyu kaihatsu (advanced grazing no kenkyu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for advanced glazing in which solar energy is efficiently utilized. The peripheral techniques are surveyed for evaluation of characteristics of large-size dimming glass, optimization of film compositions and scaling up. The dimming device, made on a trial basis, attains a target controllable rage of at least 50% for visible light transmittance. The suitable components include WO3 as the electrochromic material producing color under a reducing atmosphere, NiO as the counter electrode producing color under an oxidative atmosphere, and hydrated SbOx as the proton-conducting electrolyte. The test results indicate possibility of the dimming glass stably operable while being irradiated with a quantity of sun ray of around 10 years. The study on scaling up the dimmer glass develops, on a trial basis, a process for producing large-size glass and evaluates its characteristics, where the film parameters are investigated. It also investigates the peripheral techniques for assembling the devices for the large-size glass, and develops useful techniques, such as those for sealants and improved sealing methods. 1 fig., 1 tab.

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 3. Research and development of a simulated environment presenting technology; 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 3. Mogi kankyo teiji gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the simulated environment presenting technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. Methods to present, evaluate and improve composite acoustic environment handle the effects compounded of air propagating sound, solid propagating sound, and low frequency sound, and researches are being performed to elucidate noise evaluation indexes. A composite acoustic environment presenting device was designed, part of which has been fabricated. In the research of a radiation model that serves for enhancing working environment, development was made on a manually controlled artificial sunlight radiation device model. To simulate the kaleidoscopically changing spectral radiation intensity in the nature, the existing filters are insufficient, and development of a new system was necessary. Therefore, the developed and fabricated artificial sunlight radiation device was provided with a function that can simulate different natural sun beams in the manner of envelope approximation. In addition, the device was provided with ultra-violet ray cutting function to make it safe for human body. In the research of high-accuracy real visual sense recognition, a high-speed prototyping system, an improved sensor system, and a contact software were prepared. The intended targets were basically achieved. (NEDO)

Fiscal 1993 report on technological results. R and D on new forming technology of composite materials (Development of innovative technology for producing members for high efficiency power generation); 1993 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

A forming technology was developed which uses superplasticity of composite materials, i.e., high-functional materials for power generating equipment for example. Activities were conducted in the three areas of (1) ceramic based composite materials, (2) development of metal-based composite forming technology, and (3) comprehensive investigation and adjustment. In (1), with a view to finding a composite forming technology, in which high tenacity materials are obtained by evenly dispersing particles or whiskers as reinforcements in a matrix, a room temperature forming technique using fine particles was exploited, as were a high temperature forming technique using fused bodies and a possibility of manifestation of superplasticity in the prepared composite materials. The materials used were Si{sub 3}N{sub 4} matrix-SiC, Al{sub 2}O{sub 3} matrix-TiC, and glass matrix composite based materials filling ceramics in fine holes of porous glass. In (2), composite forming technologies were examined for such composite materials as Al alloy matrix-SiC particulate-based by a molten metal stirring method, Al alloy matrix-ceramics short fiber-based by a high pressure forging method, Ti alloy matrix-ceramics particulate-based by a mechanical alloying method, and Al alloy matrix-ceramics particulate-based by an alkoxide method/powder metallurgy method. (NEDO)

FY 1993 report on the results of the R and D of advanced function creation processing technology. Development of technology for corrosion prevention of the petroleum production system; 1993 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

In the study of a corrosion resistant high sensitivity gas sensor, the following two technologies are needed: decrease in impurities of materials for super-higher purity, and formation of films with physically high quality such as orientation and homogeneity. Experiments were made on laser excitation separation refining, CVD, laser ablation, super-high vacuum, etc. For the stabilized formation of high-adhesion thin/thick films, studies were carried out of the surface activation for processing substrate surface before film formation, interface counter diffusion in thin film formation process, and the technology for combination of these. The higher-order structure control of materials was attempted using the reaction field combined with the photochemical reaction by the high grade photon field, based on the molecular beam vapor-deposition technology under super-high vacuum. In the synthesis of materials by the photon combined reaction field, studies were made of the design/process of a dynamic device which reacts like pulse the photon/high pressure/strong magnetic field on carbonaceous materials and a static combined reaction field device by the stationary high pressure field. A study was commenced of a synthesis method in relation to fullerene with a new structure which has unique characteristics. (NEDO)

FY 2000 report on the results of the R and D of fundamental technologies of superconductivity applications. Development of technology to process low consumption power ultra high speed signals; 2000 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

In relation to the project on the R and D of fundamental technologies of superconductivity applications, the FY 2000 results of the design/fabrication of superconducting circuits were summarized. As to the development of technology to design superconducting circuits, an increase in circuit scale was tried targeting AD converter use modulator and decimation filter. As a result, operation was confirmed in element circuits of flux quantum multiplier circuit, feed back driver, DC isolator, etc. Concerning the development of technology for standard junction and integration, RHEED observations on the thin film surface before/after etching and YBa{sub 2}Cu{sub 3}O{sub 7-x} re-deposition were tried to be made, and the potentiality as monitoring technology was indicated. With respect to the fabrication of small scale circuits for demonstration, the design/trial fabrication were made of the basic pattern of SFQ circuit elements such as DC-SFQ, T-FF and SQUID for inductance rating. In regard to the development of technology to measure characteristics of superconducting circuits, a system was fabricated for processing and measuring output signals from {sigma}-{delta} modulators by semiconductor circuits, and it made the evaluation of AD converter performance possible. (NEDO)

FY 1996 report on the results of the R and D of advanced function creation processing technology. Development of technology for corrosion prevention of the petroleum production system; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Ti-Ni micro particle composite thick films could be synthesized using pulse evaporation type/magnetic field closed type evaporation source for both high hardness and high toughness. Corrosion resistant gradient composition thick films were obtained which change in composition from Ni to CrSi2 by on-substrate collision/serial sintering technology by micro particles produced by hybrid-plasma. The following were conducted: synthesis of micro particles by laser induction vapor phase reaction, formation of collision of airsol particles, and development of the continuous creation process of nano structure advanced materials by continuous combination of microwave sintering. As the higher-order structure control technology in the molecular beam complex reaction field, studies were made of photochemical reaction, effects of magnetic field on other-molecular reaction, and functional control technology. The molecular/higher-order structure control by photochemical reaction was an important factor for sensor function improvement of the formed thin film. Photon/pressure complex reaction field device was developed and an experiment was made on the material synthesis. The diamond/cBN solid solution synthesis, etc. were conducted and the hardness next to diamond was obtained. (NEDO)

Report on fiscal 1999 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (development of technology for rationalizing use of energy); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

R and D was conducted on original processing technology for electrically functional materials as a R and D project on frontier carbon technology, with the results for fiscal 1999 compiled. In the development of film forming technology using a large morphology control film forming device, the device was introduced this year, with film forming conditions probed. In the development of large size diamond synthesis process, single crystal synthesis and evaluation were carried out using an existing microwave plasma CVD reactor, with a study of design made for the device for obtaining a target 16 mm diameter single crystal. In the development of technology for oriented diamond growth on a platinum-based metallic base plate, research was done for controlling generation of grain boundary in a diamond film, through the improvement of orientation and the reduction of non-oriented grain density of the diamond nucleated on the base plate. The studies on control technology of surface-interface and electron emission characteristics were conducted on such subjects as fabrication technology of diamond for field emission, characterization of field emission, and photoelectron emission spectroscopy of diamond. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of technologies to manufacture ultra-high efficiency crystalline compound solar cells; 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on laminated cells comprising of GaInP/GaAs//GaInAs using poly-element compound semiconductors. This paper summarizes the achievements in fiscal 1999. In developing the technology to manufacture large-area ultra-high efficiency cells, fabrication of 5-cm square GaAs cells was worked on, and a conversion efficiency of 24.7%, which is equivalent or better than that for 1-cm square cell, was achieved by using the epitaxial growth temperature for the GaAs cell structure of 600 degrees C, by adopting the p-on-p structure and by making the electrode thicker by using the plating method. Furthermore, trial fabrication was performed on 5-cm square cells also on GaInAs as the bottom cell. A conversion efficiency of 4.6% was obtained in a 5-cm square cell as a result of high level homogenization of film thickness and composition by optimizing the gas flow in growing GaInAs onto an InP substrate, and using a growth temperature of 550 degrees C. In developing the technology to form GaInP/GaAs laminated cells, discussions were given by using 5-mm square cells on especially improving the GaInP crystallinity and reducing the series resistance in the window layer. GaInP/GaAs-2 bonded lamination cells were fabricated, whereas a conversion efficiency of 19.63% was obtained without using a reflection preventing film. (NEDO)

FY 1999 report on the results of the technology development of super metal. Development of technology of high corrosion resistant iron-base fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing iron/steel materials which enable remarkable improvement of maintenance loads and longevity of oil field developmental materials, study was conducted for remarkable improvement of strength and corrosion resistance by making crystal grain of iron/steel materials micro-fine to the limit, and the FY 1999 results were summed up. The study was conducted on the technology of fine structure formation using strong magnetic field and technology to predict material quality of micro structure using computational science. As a result, it was found that the fine grain even in size can be obtained by a combination of magnetic field orientation and recrystallization. By this, an image was constructed of the industrialization process of fine grained steel production which was combined with warm rolling process and applied strong magnetic field. Using the method to homogenize the finite element method, the basement was established for the method to evaluate an effect of the second phase on mechanical characteristics of fine multi-phase structure steel. The cementite single-phase film which is an important structural phase of carbon steel was successfully formed, and the Young's modulus and Poison ratio were determined as basic data for material design. (NEDO)

Fiscal 1999 report on results of R and D of industrial science and technology that creates new industry. Development of super metal technology (development of technology for innovative metallic material); 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of obtaining higher strength/toughness and higher anticorrosion in metallic materials, R and D was conducted on technologies for grain refining/dispersing and for amorphous bulk formed bodies, with fiscal 1999 results compiled. In the technological study on grain refinement and dispersion, austenitic stainless steel and 12Cr ferrite steel were used, with creative manufacturing carried out for microcrystallized structure materials by a powder metallurgy method. The result of the study revealed that suppressing grain growth by carbide or oxide was important for grain refinement, and that homogenizing the inside of a material by hot forging after solidification forming was essential for ductility improvement. In the development of the technology for amorphous bulk formed bodies, a laser heating type forming test device was designed and manufactured, with a technique examined in which bulk amorphous of a complex-shaped article was formed through rapid quenching of amorphous alloy powder by laser. This year, a trial production was performed for the laminated solidified bodies of Ni amorphous alloy powder, and the basic data was thereby collected such as feeding of the powder and conditions of the laser irradiation. (NEDO)

Achievement report for fiscal 1998 on the research and development of a basic technology to apply superconduction. Development of a low power consuming and high-speed signal processing technology; 1998 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The development of a superconduction circuit designing and manufacturing technology has achieved the following results: with respect to designing a circuit for single flux quantum (SFQ), the 'high-speed high-accuracy AC converter for front end of software radio' was selected as the target for a prototype to demonstrate the performance of the SFQ circuit. In analyzing movements of different SFQ basic circuits, such circuit simulator software versions were introduced as Saber, WR-SPICE, Wins, and Microcap, different motion waveforms for basic theoretical circuits were derived to compare their performances, and the effectiveness was verified respectively. In trial fabrication of a small demonstration circuit, design parameters were acquired from SQUID. In developing the technology to measure superconduction circuit characteristics, the following results were obtained: with regard to the element measuring and evaluating technology, an in-plane distribution measuring device was started up; and with respect to the circuit characteristics measuring and evaluating technology, a measuring system with low noise and low magnetic field was introduced. Regarding the circuit high-speed characteristics evaluating technology, development was made on a micro-strip line and coplanar transmission route converter. (NEDO)

Fiscal 1998 R and D project on global environmental industrial technology. R and D result report on environment- friendly production technology (advanced chemical synthesis reactor); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bio reactor) kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For high-efficiency production of substances by bioreactor, study was made on a bio-control mechanism as its elementary technology. On the study of breeding technology by expression control, the structure design of a control region and development of new expression vectors had been finished, and study was made on breeding of high-efficiency recombinant production cells by using candidate expression vectors. On the study of breeding technology by multi-stage enzyme reaction control, the enzyme gene of a system synthesizing cysteine from glycerol was searched, and hydroxypyruvaldehyde hydrogenase gene was isolated as substance production model. Cysteine production Escherichia coli combined with serineacetyl transferase gene was also prepared. In addition, study started on cloning of hydroxyacetone oxidase gene. On development of reactor system technology, for conversion of serine to cysteine, study was made on optimization of a reaction condition by theory of enzyme reaction rate. (NEDO)

Achievement report on developing coal liquefaction technologies in fiscal 1998 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant) 1/2; 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. 1/2. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1998. In the operation study RUN-5, the operation was carried out by using the Tanito Harum coal of Indonesia, and raising the slurry concentration to 50% by weight. The operation stability when the high concentration slurry was used was verified, and the liquefying reaction column fluidity property data, and the material balance and heat balance data were acquired by using the NAT method. In the RUN-6 and 7, for the purpose of verifying the applicability of the NEDOL process to the wide range of coal types as the process feature, the Adaro coal of Indonesia and the Ikejima coal of Japan were used, and the operation at high slurry concentration was performed at 80% load and under the standard NEDOL conditions. The operation stability when the upper and lower limit coals was used was verified, and the operability at high slurry concentration was identified. At the same time, the liquefying reaction column fluidity property data, and the material balance and heat balance data were acquired. The development targets established by the Industrial Technology Council have all been achieved. (NEDO)

FY 1998 Annual report on research and development of industrial science and technology. R and D of carbon-based high-performance materials technology (R and D for rationalization of energy consumption); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This report summarizes the FY 1998 research and development results of carbon-based high-performance materials technology. For (control technology of morphology and electrical conduction), a large-sized morphology controlling film-making apparatus was used, to confirm synthesis of crystalline diamond films. For research on growth of large-sized single-crystal diamond, the simulated results of the vapor-phase reactions and gas flow in a plasma were compared with the observed ones, to collect the data necessary for designing a high-speed homoepitaxial growth apparatus. For R and D of heteroepitaxial growth of thin diamond films, highly single-crystalline thin platinum films were successfully formed on a sapphire substrate. For (control technology of surface-interface and electron emission characteristics), the tests were conducted using newly introduced apparatuses, an (electron emission analysis/evaluation apparatus), (high-quality carbon-based thin film synthesizing apparatus) and (element processing/treatment apparatus). It is found that electron emission efficiency is greatly improved when the substrate with diamond particle seeds is plasma-treated under specific conditions. (NEDO)

FY 1993 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1993 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The paper described the FY 1993 results of the technology to create high efficiency power generation use members. A processing method was proposed in which to manifest magnetic characteristics up to the theoretical value level, crystallization of magnetic alloy amorphous was controlled and size/configuration of precipitated micro-fine crystals are made ideal. For the development of environmental purification use high functional catalysts, experiments were conducted on the heightening of purity of materials. Namely, by the two wavelength two stage excitation method using color laser, atomic beams of the material metal emitted by electronic beam evaporating source are photo-excited up near the ionization level. These are separated from the non-ionized components by electrostatic field application, and only the ionized atoms are vapor-deposited on substrate. The separation accuracy was good. Plasma excitation of raw gas was done independently for every component, and the multi-source excitation plasma CVD was proposed which is film-formed on the substrate of which the periphery was separately controlled. The synthesis method was considered of higher-order structure control high functional organic materials which are composed of electrode reaction/high grade photon/extreme magnetic field. Study was made of complex reaction field application film-forming/molecular orientation technology using a small test device. (NEDO)

Explanative report on the achievements in research and development of a coal gasification technology in fiscal 1981. Research and development of a low-calorie gasification power generation technology; 1981 nendo sekitan gas ka gijutsu no kenkyu kaihatsu seika setsumeisho. Teikarori gas ka hatsuden gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the development works on a low-calorie gasification power generation technology in research and development of a coal gasification technology in fiscal 1981. The third sub-committee was established in the Coal Gasification Committee, and the sub-committee has summarized a survey report on coal gasification composite power generation upon having held seven discussion meetings. Surveys were carried out on the fluidized bed gasification process and the coal gasification composite power generation systems mainly in Germany and the U.S.A. where development of coal gasification technologies has been advanced. Germany and Britain who use great amount of coal are urged to find ways for how to clear the environmental criteria applied in the EC countries. The U.S.A. is moving forward the development of coal gasification technologies for power generation, chemical materials, and industrial fuel to be used as the substitutes to petroleum. This paper describes the development works at the Electric Power Development Company to realize a coal gasification composite power generation system of 1,000 t/d class. The pressurized fluidized bed system is assumed, and a verification test is scheduled to be performed on the chemical reaction characteristics by using a 40-t/d furnace. The furnace shape will be decided upon executing high-pressure cold model experiments. Fiscal 1981 has fabricated and installed devices for the high-pressure coal feeding system. Operation tests, air tightness tests, and instrumentation tests have verified normal operation. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 5. Development of hydrogen transport/storage technology (development of tanker for liquid hydrogen); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 5. Suiso yuso chozo gijutsu no kaihatsu (ekitai suiso yuso tanker no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As a part of the WE-NET project, the tanker for liquid hydrogen transport was studied. In fiscal 1996, some experiments and numerical analyses were proposed which are necessary to solve technological issues extracted in fiscal 1995 for heat insulation structure. The issue was roughly classified into vacuum and non-vacuum insulation, and their basic functions and required performance were arranged. Boil-off rate of 0.2-0.4%/d was targeted. The insulation system which applies polyurethane form (PUF) to tank surfaces and injects atmospheric N2 gas into the surrounding hold space, could achieve the targeted insulation performance by PUF of 1m in thickness. The system of vacuum panel insulation and atmospheric N2 gas injection into a hold space required the panel of 500mm in thickness because of the large effect of metallic outer panel material. The system of vacuum hold and PUF panels was faced with the essential issue for realizing and maintaining vacuum hold. The super insulation system featured by layered insulation materials and vacuum layer spaces was also strongly affected by degree of vacuum. 23 figs., 8 tabs.

FY 1998 R and D of utilization of biological resources such as those in bioconsortia. Report on development results of techniques for utilization/production of organisms in bioconsortia; 1998 nendo fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to analyze functions and interactions of organisms having specific functions, to develop the techniques for isolating and cultivating the constituent organisms, and thereby to develop the techniques for their industrial utilization, in order to develop the techniques for handling organisms in bioconsortia as the techniques to utilize their functions, e.g., production and decomposition of materials, and also to develop the techniques for culturing/controlling microorganisms in bioconsortia and for strengthening their functions. The FY 1998 themes are development of the functional material production technology, and comprehensive study for the project. More concretely, the former includes histochemical analytical technology (development of techniques for detecting microorganisms in soil, and of techniques for in-situ detection/isolation of specific microorganisms in bioconsortia and for analysis their functions), isolation and culture technology (development of detection, separation and cultivation technology of microorganisms that are not easily cultured), functional substance production technology (technical utilization of microbial consortia for production of environment-friendly oil/water separation polymers), and functional material production technology (development of methods for artificial gene exchange in microbial consortia). (NEDO)

Report on achievements in fiscal 1999. Development of technology to utilize biological resources such as composite organism systems (development of technology to utilize and produce composite organism systems); 1999 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

It is intended to achieve the following objectives in terms of the technologies to utilize such functions as material production and material decomposition by using composite organism systems: develop a technology to handle the composite organism systems; establish a composite microorganism cultivation control technology, and a composite microorganism system function strengthening technology; develop a technology to separate and cultivate organism groups constituting them, and develop industrial utilization technologies. The fiscal 1999 has discussed developing the elementary technologies for the technology to utilize functions of the composite organism systems on the following research items: 1. a functional material production technology; and 2. comprehensive investigations and researches. In Item 1, development was made on a technology to detect, separate and cultivate microorganisms in soil as the histochemical analytical technology. Development was made on an in situ detection, separation and function analyzing technology for particular composite microorganisms as the function analyzing technology. In the separation and cultivation technology, development was made on a technology to detect, separate and cultivate difficult-to-cultivate microorganisms. In the functional material production technology, development was made on a technology to utilize microbial consortia producing environmentally harmonizing oil-water separating polymers, and a method to execute artificially the gene exchange in the microbial consortia. (NEDO)

Achievement report on developing coal liquefaction technologies in fiscal 1998 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant) 2/2; 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. 2/2. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1998. In the operation study, the coal charging operation has been carried out for 269 days (6,169 hours) in total since the operation has been launched, and the targets were achieved. In the facility repairs, periodical inspections were performed including daily maintenance during the operation, the legal inspection on the boiler and the pressure vessel of the category one after completing the RUN-5, and disassembling and opening inspections on other devices. After having completed the RUN-6 and 7, the final verification inspection and the facility rinsing were performed after the operation studies have been completed. The data acquired in the facility maintenance were summarized as part of the technological package after the assessment. The investigative researches have executed development of a liquefying reaction simulator, tests and investigations on pulverization of the liquefying catalyst, evaluation on the activity of the used hydrogenating catalyst, and investigation on the effect of the coal liquefaction facilities and products on the environment. The technologies were investigated on coal liquefaction, and the plans for disassembling studies were established. (NEDO)

FY 1992 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1992 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

The paper described the FY 1992 results of the technology to create high efficiency power generation use members. To enhance characteristics of super-high property permanent magnet up to the theoretical level, the development was proposed of a technology to control the size/configuration of micro crystal phase in association with the crystallization of alloy amorphous. For the development of environmental purification use high functional catalysts, a refining method using laser excitation was studied. The observation was also made of molecular adsorption on the Pd thin film catalyst prepared by RF sputtering. The multi-source excitation plasma CVD was proposed which was film-formed by exciting plasma as raw gas independently for each component and supplying it to the substrate of which the periphery was separately controlled. The paper also described the development of technology for ion/light combined assist ultra-thin film production for development of gas turbine combustion sensor. The study was also made of the synthesis of higher-order structure controlled high functional organic materials using the electrode interface combined field which is composed of electrode reaction/high grade photon/extreme magnetic field. In the development of the higher-order structure control technology using the photon combined reaction field, studies were made of the photo reaction film formation technology, the basic film formation technology in the combined reaction field, and the molecular orientation technology. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 5. Development of hydrogen transport/storage technology (development of storage facility for liquid hydrogen); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 5. Suiso yuso chozo gijutsu no kaihatsu (ekitai suiso chozo setsubi no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As a part of the WE-NET project, the storage facility for a large amount of liquid hydrogen (LH) was studied. Gasification loss caused by heat input of LH delivery pumps was studied for liquefaction and power generation bases assuming an pump efficiency of 70%, and the total heat and mass balance such as interface conditions for calculating the amount of boil-off gas was reviewed. The target storage capacity of 50,000m{sup 3} was reasonable, however, the performance of loading arms should be examined. The capacity around 5,000m{sup 3} of coastal localized bases was reasonable for control delivery loss caused by coastal tanker or LH container system to 2.6%. The capacity of 500m{sup 3} was suitable for inland bases, resulting in the loss of 1.2%. The concept design of the storage tank of 50,000m{sup 3} extracted confirmation of low-temperature characteristics of adiabatic materials and structures, and development of leakage inspection technology and vacuum holding technology as issues. The concept design of the underground storage tank showed that the material specifications for LNG ones are applicable to it by using proper adiabatic structures. 4 refs., 72 figs., 27 tabs.

Achievement report for fiscal 1998 on the research and development of a basic technology to apply superconduction. Development of a low power consuming and high-speed signal processing technology; 1998 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The development of a superconduction circuit designing and manufacturing technology has achieved the following results: with respect to designing a circuit for single flux quantum (SFQ), the 'high-speed high-accuracy AC converter for front end of software radio' was selected as the target for a prototype to demonstrate the performance of the SFQ circuit. In analyzing movements of different SFQ basic circuits, such circuit simulator software versions were introduced as Saber, WR-SPICE, Wins, and Microcap, different motion waveforms for basic theoretical circuits were derived to compare their performances, and the effectiveness was verified respectively. In trial fabrication of a small demonstration circuit, design parameters were acquired from SQUID. In developing the technology to measure superconduction circuit characteristics, the following results were obtained: with regard to the element measuring and evaluating technology, an in-plane distribution measuring device was started up; and with respect to the circuit characteristics measuring and evaluating technology, a measuring system with low noise and low magnetic field was introduced. Regarding the circuit high-speed characteristics evaluating technology, development was made on a micro-strip line and coplanar transmission route converter. (NEDO)

Report on the achievements in development of a coal liquefaction technology (a solvent extraction and liquefaction technology) in the Sunshine Project in fiscal 1981. Data 1. Development of a brown coal based solvent extraction plant (50 t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 1). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the data-1 for developing a brown coal based solvent extraction plant in the Sunshine Project in fiscal 1981. The data are for the development of a liquefaction plant for Victoria brown coal produced in Australia (a 50-t/d pilot plant). Fiscal 1981 has performed detailed design on the primary hydrogenation system by using the process conception and the design data obtained in the element studies. Part of the machines and devices was procured, and the site construction was begun. Detailed design documents and drawings were prepared. The data collected in relation with the plant design included the followings: device lists, entire factory layout drawings, device arrangement drawings, process flow sheets, utility flow sheets (fuel gas and fuel oil systems, steam and condensate systems, air for instrumentation, plant air, cooling water supply and return, industrial water and treated water, a waste water treatment system, a nitrogen system, and a waste gas system), public pollution preventing facilities, hazardous location classifying plans, and material balances. The data collected in relation with the machine design included pressure vessel engineering specifications, heat exchanger engineering specifications, and device purchase specifications. (NEDO)

FY 1998 annual report on the preliminary research and development of techniques for developing resources from gas-hydrate. Studies on gas-hydrate exploration, excavation techniques, methods for assessing environmental impacts, and gas hydrate handling systems; 1998 nendo gas hydrate shigenka gijutsu sendoken kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no kenkyu kaihatsu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This R and D project is for the preliminary studies on development of the following 4 types of techniques for developing resources from gas-hydrates (GH): (1) gas-hydrate exploration, (2) excavation techniques, (3) methods for assessing environmental impacts, and (4) gas hydrate handling systems. The FY 1988 R and D results are described. For gas-hydrate exploration, the methods for analyzing inorganic ions and trace quantities of elements, which are necessary for accurately estimating the offshore GH around Japan, are established; and case studies are conducted for methods of predicting GH deposit forming mechanisms, and stability fields of GH, based on terrestrial heat flow and seismic data. For excavation techniques, GH decomposition rate is analyzed using a laboratory system which reproduces conditions of excavation of GH layers. For methods for assessing environmental impacts, a geo-hazard predicting model is established, to study ground displacement and gas leakage sensing systems and data transmission systems to cope with the hazards. For gas hydrate handling systems, an overall system is studied, and storage and transportation systems are outlined. (NEDO)

FY 1998 report on the results of the research and development of fundamental technologies for superconductor applications; 1998 nendo chodendo oyo kiban gijutsu kenkyukaihatsu seika hokokusho. Chodendo oyo kiban gijutsu keknyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

As to the research on the superconductor manifestation mechanism, Y123 monocrystal which was partially replaced with Zn and Ni was manufactured, and it was made clear that the addition of these impurities greatly change anisotropy of superconductors. It was made clear that instability of lattice and magnetism is included in high temperature superconductor. Also made clear was an important role in the Nb/Ba replacement in existence of magnetic flux melting phase transfer and the magnetic field induced pinning effect. The manufacture of Y123 bicrystal membrane was successful by the liquid phase epitaxy method. The manufacture of non-copper base K-Bi-O new superconductor was successful by the ultra-high pressure synthesis method. The stabilized process was established for large size crystals of 15-20mm square in Y base and of 20-25mm square in Nd base. Also successful was the growth by LPE method of crystal with thick membrane of 20mm x 20mm x 10{mu}m on the MgO monocrystal substrate. The non-bicrystalization of Y base Nd base monocrystal was successful, and the peak phenomenon control in Jc-H was found out. By neutron irradiation, the acquisition magnetic field of 3.7T at 77K was achieved using bulk Y base 123 material with diameter of 3cm. And, the critical current density of 60,000 A/cm{sup 2} was achieved at 77K and 3T. (NEDO)

FY 1998 annual summary report on photon measuring/processing techniques. Development of the techniques for high-efficiency production processes; 1998 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to develop the techniques for energy-efficient laser-aided processing; techniques for high-precision, real-time measurement to improve quality control for production processes and increase their efficiency; and the techniques for generating/controlling photon of high efficiency and quality as the laser beam sources therefor, in order to promote energy saving at and improve efficiency of production processes consuming large quantities of energy, e.g., welding, joining, surface treatment and production of fine particles. The R and D themes are microscopic processing technology: simulation technology for laser welding phenomena; microscopic processing technology: synthesis of technology for quantum dot functional structures; in-situ status measuring technology: fine particle elements and size measurement technology; high-power all-solid-state laser technology: efficient rod type LD-pumping laser modules and pumping chamber of a slab-type laser; tightly-focusing all-solid-state laser technology: improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology and fabrication technology for nonlinear crystal; and comprehensive investigation of photonics engineering: high-efficiency harmonic generation technology. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program. Practical application technologies for photovoltaic power systems (Development of peripheral technologies); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu seika hokokusho. Shuhen gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

As for their outputs, the 3kW separately-excited and self-excited photovoltaic power plants yield daily averages of 7.8kWh and 6.9kWh, respectively, and this means that the self-excited type is inferior to the separately-excited type in terms of conversion efficiency. Automatic measuring devices for photovoltaic characteristics are installed at Sapporo, Sendai, Nagoya, and Miyazaki, which will elucidate regional difference in photovoltaic characteristics. A simulation of photovoltaic characteristics is performed and the resultant value is compared with the yield of an experimental 3kW system, and the result of the comparison is found reasonable. Cell arrays are subjected to investigation for configurations lowest in output loss for the respective shadow patterns. Harmonic characteristics are analyzed under plural-interconnection circumstances. Studies are made to miniaturize and simplify system constituents, and it is found that a 3-hour storage is proper for a 3kW-class storage battery. It is also found that a self-excited type suffers less voltage fluctuation in interconnected operation on a small short-circuit capacity system. Possibilities are that independent operation is started when output is larger than load, which is to be detected by checking changes in phase, frequency, etc. Array configuration, arresters, and shielding wires are taken up for the study of measures to cope with direct thunder strokes. (NEDO)

FY 1998 annual summary report on photon measuring/processing techniques. Development of highly functional maintenance techniques for power generating facilities; 1998 nendo foton keisoku kako gijutsu. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to develop the techniques for non-destructive measurement of conditions of facility portions, especially those exposed to severe environments, e.g., elevated temperature and pressure, over a wide range; the techniques for measurement of leakage of, e.g., gases, at high sensitivity; the techniques of laser-aided welding and surface-modification treatment for the members exposed to severe conditions; and the techniques for generating photon beams of high quality and energy density as the tools therefor, in order to improve reliability and maintenance efficiency of power generating facilities. The R and D themes are microscopic processing technology: fabrication technology for functional micro-composite circuits; in-situ status measuring technology: gas concentration/component measurement technology, and photon wavefront compensation device technology; non-destructive composition measuring technology: high-sensitivity detection technology using short-wavelength photons; high-power all-solid-state laser technology: rod-type laser and slab-type laser; tightly-focusing all-solid-state laser technology: high-energy pulse, high-quality laser; and comprehensive investigation of photonics engineering: investigation for photon-applied measurement technologies. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 4. Development of hydrogen production technology; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 4. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper describes development of hydrogen production technology as a part of the WE-NET project. For the solid polymer water electrolysis method higher in efficiency and lower in cost than the previous methods, 5 companies have developed element technologies for improving electrolysis cells and synthesis technologies of hot solid polymer electrolyte based on each proper catalyst electrode production method. In fiscal 1996, the initial study on large-scale systems by middle laboratory cells was made as well as improvement of electrolysis performance by small laboratory cells and endurance tests. Among the previous methods such as a hot press method (bonding of an ion exchange membrane to an electrode), an electroless plating method (preparation of porous surface onto a membrane electrode assembly), a zero gap method (preparation of high-efficiency high-current density cells), and a sintered porous electrode method (carrying of the mixture of catalytic powder and ion exchange resin-dissipated solution onto sintered metallic porous electrode surface), the former two methods were adopted for development of bench-scale cells as effective promising methods. 192 refs., 183 figs., 108 tabs.

Fiscal 1997 survey report / R and D of important region technology. R and D of technologies giving multi-functional characteristics to C/C composites (development of high-grade surface processing technology for engine members for methane fueled air craft. 1. control technology of micro structures of ultra-high temperature members); 1997 nendo seika hokokusho juyo chiiki gijutsu kenkyu kaihatsu. Fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). 1. chokoon buzai micro kozo seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of developing members most suitable for aircraft use engines with methane as fuel, the R and D were conducted of technology to reform surfaces and interfaces of materials. In the R and D, the paper took up carbon fiber reinforced carbon composite materials (C/C composites). In the surface control and reformation technology using the ion engineering method, etc., in the sealing processing of C/C composites, tried was the formation of a C/SiC/Si3N4 composite layer which was formed by Si3N4 much smaller in thermal expansion coefficient than SiC. Further, technologies on ion injection, thin film formation, giving of oxidation resistance/corrosion resistance, improving/giving of thermal shock resistance, etc. In the multi-functional coating formation technology such as high liability and corrosion resistance, the study was carried out of the dense composite functionally-gradient layer as thermal stress relaxation layer and the fiber reinforced layer by carbon fiber using pores. Besides, studies were made of technologies of the micro structure control combination, evaluation of ultra-high temperature resistant environmental characteristics, etc. 61 refs., 198 figs., 44 tabs.

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of environmental adaptation of next-generation solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - jisedai taiyo denchi kaihatsu kankyo tekioka chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Surveys are conducted of photovoltaic power system development projects and their utilization in Japan and overseas, and a discussion is made on the progress, technical challenges, effects, and implementation systems relating to the solar cell application technology development project under the New Sunshine Program. Compiled in the report are the results of surveys of the research and development of photovoltaic power systems and their diffusion in the U.S. and European nations, and the research and development strategies for and the trends of the development of various types of solar cells in these countries. The trends of research and development of non-conventional type solar cells are also collected, which include 3 cases of TPV (thermophotovoltaic) devices, 5 cases of new inorganic materials, 1 case of new organic materials, and 4 cases of dye-sensitized solar cells. In relation to the status of resources of crystalline compound-based solar cell materials, raw materials for solar cells other than silicon are taken up, and their reserves, manufacturing methods, quantities yielded and consumed, costs, etc., are surveyed. These are all taken into consideration in discussing the basic approach to the study of future research and development as it ought to be. (NEDO)

Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Development for practical application of a new production process); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Shinseizo process jitsuyoka kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The research and development aims to establish, through verification tests, practical application technologies for two methods, namely, a 'low-temperature liquid phase method' by which cost will be reduced thanks to simplified plant facilities and a 'vapor phase fluidized bed method' in which a composite reforming process may be combined for better economics of scale with a vapor phase fluidized methanol synthesizing method whose facilities may be built to be very large. For the former method, development efforts are made to enable catalyst performance characterization and low-temperature liquid phase methanol production using a small pyrolysis reactor. In the research on pyrolysis reaction, a Raney copper/KOMe/MeOH-based catalyst is used, and this attains a raw material gas conversion efficiency of 92.7%. In the construction of a low temperature liquid phase process, it is found that a single spun conversion efficiency of not less than 90% may be achieved using a heterogeneous catalyst. For the latter method, studies are conducted for the development of, and for the establishment of technologies for designing, synthetic gas production technologies in the development of a heat exchanger type composite reforming furnace and a fluidized bed methanol production process, the development of a catalyst manufacturing technology for fluidized bed practical application, the development of a fluidized bed methanol production technology, and the optimization of the process and its economic efficiency. (NEDO)

Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

Fiscal 1996 report on technological results. R and D on micromachine technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches on basic element technology of micromachines are conducted that operate autonomously in a narrow small part in a complicated apparatus or in vivo. The areas of activity are (1) research on micromachine systems, (2) a subminiature liquid synthesizing system, and (3) comprehensive investigation and research. In (1), the researches were carried out on the miniaturization and functional combination of a micro laser catheter and a micro tactile sensor catheter, which are the primary components of a coeliac diagnostic and therapeutic system, a 'micro catheter for cerebral blood vessel/treatment', as a micromachine system in the medical field. In (2), R and D was conducted on a system element technology assuming it contributed to a subminiature liquid synthesizing system capable of preparing various liquids including pharmaceuticals accurately with a trace amount. In (3), examination was made on the application area of a micromachine system with priority given to a medical field and also on technological subjects to be tapped, as well as on the contents of (2), with a device installed for evaluating the operating characteristic of a distribution type fluid actuator as needed for the development. (NEDO)

Fiscal 1997 report on technological results. R and D on micromachine technology; 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches on basic element technology of micromachines are conducted that operate autonomously in a narrow small part in a complicated apparatus or in vivo. The areas of activity are 1. research on micromachine systems and 2. comprehensive investigation and research. In 1, (1) a micro catheter and (2) a micro tactile sensor catheter were studied while, in 2, basic technology and technological problems, particularly those problems concerning sophistication in the medical field were examined and studied. Further, in (1), with the purpose of developing a micro laser catheter for diagnosis/treatment, researches were implemented on the technology of integrating micro laser and an optical fiber which were components of the catheter and on the fabrication of the fine diameter of a micro catheter as well as on the characteristical improvement of the base body on which minute elements were mounted. In (2), characteristical improvement and sophistication were carried out for a high sensitivity contact pressure sensor and a diagnostic tactile sensor, which are mounted on a catheter having a positive bulge control mechanism for insertion into body cavity, with a sensor probe manufactured experimentally. (NEDO)

Report on the fiscal 1996 development of high efficient waste power generation technology; 1996 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The technical development was made by which high-temperature/high-pressure steam is generated in the incineration furnace using general waste, combustible industrial waste, etc. as fuel to generate power high efficiently, and reliability of the superheater, etc. was verified by the pilot plant. For it, the following were conducted: development of element technology (high-temperature/high-efficiency combustion furnace, corrosion resistant super heater materials, environmental load reduction technology) and the demonstration (demonstrative test in pilot plant, study of an optimum total system). In relation to the external circulation type fluidized bed furnace, reformation was made which enables simultaneous sampling of dioxins, etc. The combustion test was done using the reformed combustion testing furnace to obtain the data necessary for the study of formation/decomposition mechanism of dioxin. The amount of corrosion reduction of superheater sample material for pilot plant use was determined. A study was made of improvement of removal of dioxins and NOx in the pulse plasma exhaust gas treatment method. The pilot plant was installed. 10 refs., 205 figs., 79 tabs.

Development of technology for fuel alcohol. ; Searching and breeding of superior bacteria. Nenryoyo alcohol gijutsu kaihatsu. ; Yushukin no kensakuter dot ikushu

Energy Technology Data Exchange (ETDEWEB)

1990-10-01

In order to develop superior ethanol fermenting bacteria which would directly transform fibers into ethanol, which would lead to the utilization of unused waste industrial agricultural and forestry products, separation of potential strains from extensive collections of microbe resources from in and out of this country and adding of salt resistance, alcohol resistance, cellulose digestion properties using bio-technology were conducted. In searching for superior bacteria, some cells used in the sugar test plant showed no decrease in fermentation yields in 0.4% CaCl{sub 2}, 0.25 MgCl{sub 2} cultures, and some showed no decrease even with 1% KCl. In the breeding of superior bacteria, zymomonus with 4 times CMCase (a component enzyme of a cellulose degrading enzyme) activity, zymomonus which could grow in maltose cultures, zymomonus which had xylose isomerase genes linked to pyruvate carboxylase promoters, zymomonus resistant to 7% ethanol and 1% KCl, thermophilic and anaerobic cellulose degrading bacteria were developed. 1 tab.

Achievement report for fiscal 1998. Development of next-generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researches are conducted on the development of a technology of catalytic cracking of naphtha, technology relative to selective oxidation reaction of saturated hydrocarbons, process technology utilizing solid-phase reaction field, and a process technology utilizing novel reaction mechanism. Also, a survey is conducted on chemical processes of the next generation. Concerning the catalytic cracking of naphtha, reaction systems are roughly divided into two groups by whether or not they proceed in the presence of oxygen. As for rare earth oxide catalyst systems and zeolitic catalyst systems, their performance is confirmed and their reaction mechanisms are estimated. Concerning the selective oxidation reaction of hydrocarbons, studies are made to enhance the performance of catalytic systems that have been selected in researches conducted in the past. Concerning the process of solid phase reaction field utilization, the project is summarized and a concept is constructed of 'solid phase catalyst.' Concerning novel reaction mechanism utilizing process technologies, development is discussed of a novel process using membrane reactor, a highly functional hydrogen permeable membrane, a low-temperature dehydrogenation catalyst, etc., and a dehydrogenation membrane reactor is experimentally built. (NEDO)

Data book on new energy technology development in FY 1997. Cogeneration; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Cogeneration

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Various policies are being implemented in the field of new energy technology in line with progress in technological development. Examples are about assistance mechanism, field test projects and advisory projects to support the introduction of new energy technology. In order to promote the introduction of new energy efficiently, it is necessary to compile the various information regarding new energy in a comprehensive and systematic way, and formulate a basic data set. Among various new energy technologies, cogeneration is discussed in this report. The latest published data on the respective technologies are compiled particularly regarding their overall systems, examples of introduction, assistance mechanisms and state of implementation in foreign countries. Items included in this report are the trend of cogeneration, outline of system, state of introduction, forecast of introduction, overview of policies, basic terms, and related organizations. 9 figs.

Survey on problems in developing technologies for the global environment issues (Version II); Chikyu kankyo mondai gijutsu kaihatsu kadai chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-07-01

This paper describes a survey on problems in developing technologies for the global environment issues. Technological development of means to reduce generation of environmental issues and substitutive means for non-generation thereof is being moved forward specifically in the Sunshine Project and the Moonlight Project. The Chemical Technology Research Institute assumes that it has a responsibility to positively contribute to developing a technological system that matches the substance circulation mechanism of the earth from the fields of chemistry. Therefore, the Institute has organized working groups that have been identifying problems from their expertise standpoints and have been extracting study assignments. Subsequent to the Version I, the Version II has been compiled. The Version II takes up the simulation of global warming mechanisms, behavior of gases dissolved in oceans, and possibility of fixing CO2 in oceans. With respect to fluorocarbons, the Version II describes development of substitutive substances, their stability, combustion method as a destruction technique, and destruction by means of super criticality. Regarding CO2, the version introduces technologies to re-use CO2 as a resource by means of membrane separation, storage, and contact hydrogenation. The volume also dwells on CO2 reduction by using photo-chemical and electrochemical reactions, CO2 reduction and photo-synthesis by using semiconductors as photo catalysts and electrodes. (NEDO)

Achievement report for fiscal 1998. Development of next-generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researches are conducted on the development of a technology of catalytic cracking of naphtha, technology relative to selective oxidation reaction of saturated hydrocarbons, process technology utilizing solid-phase reaction field, and a process technology utilizing novel reaction mechanism. Also, a survey is conducted on chemical processes of the next generation. Concerning the catalytic cracking of naphtha, reaction systems are roughly divided into two groups by whether or not they proceed in the presence of oxygen. As for rare earth oxide catalyst systems and zeolitic catalyst systems, their performance is confirmed and their reaction mechanisms are estimated. Concerning the selective oxidation reaction of hydrocarbons, studies are made to enhance the performance of catalytic systems that have been selected in researches conducted in the past. Concerning the process of solid phase reaction field utilization, the project is summarized and a concept is constructed of 'solid phase catalyst.' Concerning novel reaction mechanism utilizing process technologies, development is discussed of a novel process using membrane reactor, a highly functional hydrogen permeable membrane, a low-temperature dehydrogenation catalyst, etc., and a dehydrogenation membrane reactor is experimentally built. (NEDO)

Fiscal 1982 Sunshine Project research report. Development of bore hole measurement technology; 1982 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This report summarizes the fiscal 1982 research result on development of measuring instruments for information collection in geothermal bore holes under high-temperature high-pressure conditions. In development of high-temperature well logging cable, the new TFE Teflon insulated well logging cable (3,300m) applicable up to 320 degreesC was prepared. In development of digital well logging system, the data analyzer for edition and analysis of recorded digital logging data, the depth panel with an automatic depth correction mechanism, and the fiber optics controller were prepared. Preparation of the whole digital well logging system was thus completed. Field test was made at 3 wells in 2 geothermal areas. At the test well in Nigori-Gawa area, Hokkaido, performance test was made on the digital well logging system, TFE Teflon well logging cable, and improved winch completed in this fiscal year. At the same time, the radioactive well logging test using radioactive isotope showed the satisfactory result except neutron well logging. (NEDO)

FY 2001 report on the results of the follow-up study of development of the highly effective waste power generation; 2001 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu no follow up gijutsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of safe operation of the highly effective waste power generation pilot plant, confirmation of the performance of corrosion resistant super heater materials under the high temperature corrosion environment, collection of the data on environmental load characteristics in waste incineration, etc., the follow-up study was made. The results were as follows: The pilot plant was able to generate high temperature/high pressure vapor stably for approximately 13,500 hours in FY 2000 and FY 2001 and for approximately 27,800 hours in 4 years since the start of the demonstrative test. The planned performance of plant facilities was fully satisfied, and the performance of environmental load reduction was fully satisfied in standard values of soot/dust, SOx, NOx, hydrogen chloride and dioxins in exhaust gas. Concerning the super heater use developmental material, its durability of 5 years or more was confirmed. It was forecast that by using this, the heightening of temperature/pressure of boiler to 500 degrees C and 100 atmospheric pressure was achieved. Further, the useful information/knowledge on plant design were obtained such as the corrosion prevention technology for waste plant and the forecast of corrosion life of materials. (NEDO)

Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology; 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (femto byo technology no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Ultrahigh-speed electronic technology is indispensable for creating industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. To establish the development policy of generation and transmission devices for femtosecond light pulses, research and analysis were made on nonlinear optical response and light pulse transmission properties. Basic issues on devices and materials such as mode-locked semiconductor laser, pulse compression device and light-light modulation material for coding were extracted. For new femtosecond light pulse control/distribution devices, research and analysis were made on response properties of intersubband transition phenomena in a semiconductor and electron spin relaxation phenomena, and semiconductor quantum structure. To develop metrological technology using ultra-short light pulse, study was made on an evaluation method for time- fluctuation of pulses in 100 femtosecond level. Generation of femtosecond high-intensity X-ray pulse was possible by fine control of the existing high-intensity laser. 19 refs., 26 figs., 1 tab.

Fiscal 1997 report on the development of an energy use rationalization ultra-high tech liquid crystal technology. Project of development/promotion of ultra-high tech electronic technology / technology of design/control/analysis of new functional electronic materials; 1997 nendo kenkyu seika hokokusho energy shiyo gorika chosentan ekisho gijutsu kaihatsu. Chosentan denshi gijutsu kaihatsu sokushin jigyo / shinkino denshi zairyo sekkei seigyo bunseki gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

A research was conducted with the aim of developing an ultra-low power consuming type information display which supports the next next generation informatizing society. As to the function combined type fine structure formation technology, a formation technology of fine structure supporting multi-layer pixel by organic polymer materials was established to confirm a possibility of adopting it to high functional liquid crystal display. Concerning the high functional fine structure formation technology, a study was proceeded with on holographic PDLC which is an interference reflection coloring method. In relation to the low temperature film formation technology of ferroelectric thin films, a film formation device was introduced to obtain basic data, and at the same time a possibility was studied of improving film characteristics by laser annealing conducted after the film formation. Moreover, concerning the new functional material technology, studies were made of optical interference/high light-scattering control materials, light alignment elements, ultra-high purity/ultra-reliable optical materials, ultra-anisotropy optical materials, etc. About the light reflection characteristics control technology, studied were new liquid crystal molucular orientaion control technology, multi-dimensional anisotropy structure formation technology, etc. 100 refs., 273 figs., 58 tabs.

Achievement report for fiscal 1998 on research and development of multifunction members structure control technologies. Development of advanced surface treatment technologies for methane-fueled aero engines (1. Microstructure control technologies for ultrahigh temperature members); 1998 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (chokoon buzai mikuro kozo seigyo gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The carbon fiber reinforced carbon composite materials (C/C composites) strong at ultrahigh temperatures are taken up. So as to improve on its resistance to oxidation, corrosion, and abrasion as well as on its strength at ultrahigh temperatures, an ion engineering-assisted technique is used to reform the C/C composite surface layer and a technology is developed for thin coating formation on the C/C composite surface. Next, technologies are developed for multifunction coating formation on top of the surface, for defect prevention or removal from the C/C composite, and for adhesion enhancement between the C/C composite fibers and the matrix. Technologies are further developed for evaluating hostile environment withstanding capabilities at ultrahigh temperatures. In this fiscal year, in the study of microstructure controlling multilayer coating technologies, development is conducted of technologies of ion engineering-assisted surface control and reform and of technologies of forming multifunctional coatings high in reliability and resistance to corrosion. In the field of microstructure control composition, 3-dimensional carbon fiber reinforced carbon composite materials are manufactured by way of trial and evaluated, and their behavior under rigorous conditions is evaluated. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and dessolution deposition process); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu (yokai sekishutsuho))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to manufacture low-cost large-area solar cell modules, developmental research has been performed on a film manufacturing technology using the dessolution deposition process. This paper summarizes the achievements in fiscal 1999. The research has been performed on a technology to form a thin silicon film directly on carbon substrates being substrates of different kinds, without using seed crystals. The researches made up to the previous fiscal year has made possible to form the film onto a substrate of about 5-cm square, has fabricated cells although with a small area, and indicated the importance of reducing concentrations of impurities in the solvent metals used. The researches performed during the current fiscal year executed modifications to reduce the temperature distribution in the substrate surfaces, including size increase in the heater, and improvement in the cooling heat conduction mechanism. As a result, films were formed successfully on 7.5-cm square substrates. In reducing the process temperatures, it was made clear that films can be formed at lower than 700 degrees C by using zinc as a solvent metal. Furthermore, the purity enhancement in the solvent metal achieved a conversion efficiency of 11.6% although the area is as small as 3.73 cm{sup 2}. (NEDO)

FY 1998 research result report. Ultra-high liquid crystal technology development for energy use rationalization (Technology of design/control/analysis of new functional electronic materials of the ultra-high electronic technology development promotion project); 1998 nendo kenkyu seika hokokusho. Energy shiyo gorika chosentan ekisho gijutsu kaihatsu (chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Element technology is studied to realize a reflective-type, full-color, and high-resolution liquid crystal display for super-low power consumption data display. As to the functional compound microstructure formation technology, a 4-inch panel was trially fabricated using two-layer guest-host liquid crystal technology to achieve the desired display performance by control of molecular orientation. Further, holographic PDLC elements were favorably test-fabricated. A ferroelectric PZT thin layer was formed by forming layer at low temperature at which a glass substrate can be used. Optical interference/optical dispersion type optical control materials were studied by liquid crystal/polymer composition. Also studied were super-pure/super-reliable liquid crystal compound/liquid crystal composite systems and super-anisotropic liquid crystal compound by modeling ionic impurities and liquid crystal molecular interaction. In relation to the control technology of optical reflection characteristics, effects of liquid crystal molecular structures (derivative effect and copolymer composition) on orientation were elucidated. As to the technology to form multi-dimensional anisotropic structures, efforts were made for the heightening of formation technology of simple RGB (red, green, blue) directional reflection layers using acrylate materials. The paper also outlined the comprehensive survey. (NEDO)

Fiscal 2000 research achievement report on the development of super-advanced liquid crystal technology for energy use rationalization. Development promotion project for super-advanced electronic technology - Design, control, analysis, etc., of electronic materials having novel functions; 2000 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo (shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-04-01

Efforts are focused on the verification of target devices under the respective subjects, and activities are conducted with the development system reinforced. Three newly proposed reflection type liquid crystal devices achieve the target specifications of a reflection factor of 60% or higher and a contrast ratio of 15:1 or higher. Studies are conducted involving the five fields of (1) multilayer reflection devices, (2) memory retention liquid crystal devices, (3) single pixel color devices, (4) directional reflection devices, and (5) joint research. Research and development in field (1) covers ultra-anisotropic optical materials, ultrahigh reliability host liquid crystal materials for guest-host liquid crystals - mixed system, low voltage driven/high load holding liquid crystal compound systems, and new liquid crystal molecule orientation control technology; in field (2), low temperature fabrication of ferroelectric thin film, and ultrahigh purity high reliability liquid crystal compounds; in field (3), materials capable of controlling optical interference and higher order light scattering, photoregulation devices, highly birefringent liquid crystal materials - mixed system, and ultrahigh efficiency light scattering liquid crystal compounds; and, in field (4), multi-dimensional anisotropic structure fabrication technology and ultra-anisotropic optical materials. (NEDO)

FY 2000 Report on the results of research and development of the important regional technologies. Development of high-order processing of high-melting metal-based parts (Development of technologies for creating parts for high-efficiency power production); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Koyuten kinzokukei buzai no kodo kako gijutsu (kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research and development of heat-resistant materials, aimed at increasing operating temperature of gas turbines not equipped with a cooling system and thereby further improving their thermal efficiency. The program for design/evaluation of high-strength, Nb-based solid solution alloys develops the Nb-based alloy reinforced with a solid solution comprising 5 to 30% of Mo and 5 to 15% of W, all by atom, simultaneously dissolved. The program for design/evaluation of high-strength, Nb-based composite materials confirms effectiveness of incorporating Si in a Nb alloy and separating silicide in the Nb-based solid solution alloy matrix as the combined mechanism of reinforcing the alloy. The program for creation/evaluation of Nb-based parts which withstand superhigh temperature finds that the discharge plasma method gives the structure, in a very short time, almost on a level with that given by the solution solidification method. The program for oxidation resistance improving technologies develops the electrochemical process for forming the oxidation-resistant coating film. The stable oxidation-resistant performance is observed in the preliminary test, because the sample loses no weight when exposed to around 1000 degrees C in air for 10 hours. (NEDO)

FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of drilling technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen kussaku gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of developing deep geothermal resources, development of 'drilling technology of deep geothermal resources' was made from FY 1991 to FY 2001, and the results were summarized. As to the development of bits, the bit that can be used for 30 hours or more at a temperature of 250 degrees C was developed, and the demonstrative test was made in FY 1997. Relating to the development of the high temperature use drilling mud, the mud that can be used at a temperature of 350 degrees C was developed, and the test using the actual well was conducted in FY 1997. Concerning the development of the high temperature use cement slurry, the cement slurry with specific gravity of 1.35 or below that can be used under the environment of a temperature of 350 degrees C was developed, and the hanging test of the specimen was made in the actual well in FY 1998. About the development of the high temperature use downhole motor, a prototype of 1/12 scale was fabricated in FY 1998, and the performance test at high temperature was conducted. As to the development of the high temperature use high strength cement slurry, a cement slurry with specific gravity of 1.50 or below and compressive strength of 19.61 MPa that is used under the environment of a temperature of 300 degrees C was developed, and the test on the long-term compressive strength was made in FY 2001. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the solar cell evaluation system; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka gijutsu no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was made of the development of the basic technology for the integrated evaluation of solar cell performance, grasp of degradation phenomena of solar cell modules by outdoor exposure test, development of the accelerated degradation test method, etc., and the FY 2000 results were summed up. As to the development of the ultra-high approximation solar simulator for cell evaluation, a simulator was fabricated of which the irradiation non-uniformity is {+-} 1.0% and the spectral agreement is within {+-} 10% in 10 wavebands out of the 16 wavebands. Relating to the development of evaluation technology of large area modules, performance of the spectral irradiance distribution, etc. was improved by modification of the solar simulator, which made accurate measurement possible. In the study of degradation of solar cell modules, exposure tests on various kinds of solar cell modules were continued at 5 sites in Japan, 3 sites in Australia and 1 site in Oman for data collection/analysis. Further, analysis was made of Isc changes in the early stage of exposure, phenomenon of cell's cloudy discoloration, degradation caused by increase in series resistance, etc. As the test method of light accelerated degradation of A-Si solar cell, a brightness cycle test method was developed. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the solar cell evaluation system; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka gijutsu no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was made of the development of the basic technology for the integrated evaluation of solar cell performance, grasp of degradation phenomena of solar cell modules by outdoor exposure test, development of the accelerated degradation test method, etc., and the FY 2000 results were summed up. As to the development of the ultra-high approximation solar simulator for cell evaluation, a simulator was fabricated of which the irradiation non-uniformity is {+-} 1.0% and the spectral agreement is within {+-} 10% in 10 wavebands out of the 16 wavebands. Relating to the development of evaluation technology of large area modules, performance of the spectral irradiance distribution, etc. was improved by modification of the solar simulator, which made accurate measurement possible. In the study of degradation of solar cell modules, exposure tests on various kinds of solar cell modules were continued at 5 sites in Japan, 3 sites in Australia and 1 site in Oman for data collection/analysis. Further, analysis was made of Isc changes in the early stage of exposure, phenomenon of cell's cloudy discoloration, degradation caused by increase in series resistance, etc. As the test method of light accelerated degradation of A-Si solar cell, a brightness cycle test method was developed. (NEDO)

FY 1999 research and development of technologies for creating original high-function materials. Development of technologies for functionalized materials for power generating facilities (Report on the R and D results of controlling precise structures of polycondesed systems); 1999 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu (shukugokei seimitsu kozo seigyo no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for the polymerization catalysts and precise polymerization processes which can freely control the primary structures, e.g., molecular weight, regularity, branching and terminal group structures, of the polymers produced by polycondensation and ring-opening polymerization, in order to drastically improve their functions, and the FY 1999 results are reported. The basic studies on the precise polycondensation successfully lead to chemoselective synthesis of polymers by the direct polymerization, and synthesis of polyamides of narrow molecular weight distribution and high-molecular-weight aliphatic polyesters. The other items studied include precisely, regularly sequential polymerization by amine activation, innovative synthesis of polycarbonate, precise control of branching structures, regioselective oxidative coupling polymerization, and matrix polycondensation. The basic studies on the controlled ring-opening polymerization cover cationic ring-opening polymerization behavior of 6-membered thiocarbonate derivative having an ester group, to generalize the polymerization controlled by neighboring group participation. The other items studied include precise control of branching structures, molecular weights, network polymer structures, and polymer unit sequences. (NEDO)

Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of a geothermal water use power plant, etc. / technical development of the hot dry rock power generation system (development of electric technology); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of using hot dry rock energy to power generation, the R and D was continued of element technology of the hot dry rock power generation. In fiscal 1997, the construction of ground facilities, etc. for long-term circulation experiment was proceeded with to make data analysis for study of the experimental results. As for preparation for the long-term circulation experiment, design/fabrication/construction of experimental facilities were commenced, and review/fabrication of the monitoring system were conducted to strengthen the monitoring network of microearthquakes. In relation to the analytical research, using models connecting reservoirs and wells, relationships were studied among the distance between injection well and production well, production flow rate, and long-term thermal extraction characteristics of reservoirs. Further, to study structures of shallow/deep reservoirs at the Hijiori hot dry rock experimental field, re-determined were mechanism solutions of AE in deep hydraulic fracturing experiments, three well circulation tests, and preliminary circulation tests, and at the same time stress fields were studied. Fracture models were made and the simulation program was revised. 18 refs., 82 figs.

FY 1998 report on the results of the R and D of industrial science technology. R and D of 'carbon-base high functional material technology' (R and D of the submarine oil production support system); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu (kaitei sekiyu seisan shien system kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

For the R and D of carbon-base high functional materials, the paper reported on (1) material creation technology and (2) creation of mechanically high functional materials. In (1), the synthesis of new BCN-base materials is conducted by the electronic excitation CVD method and high temperature/high pressure (explosive synthesis) with the aim of analyzing the composition/structure. Using energy-controlled ion beams and laser beams, the synthesis of new CN-base materials and analysis of composition/structure are aimed at. By the thermal CVD method using catalysts, a method to synthesize a quantity of nanotubes is aimed at. The paper is aimed at clarifying the reaction mechanism on the material conversion of carbonaceous materials relating to the above-mentioned three methods and the appearance mechanism of characteristics of carbonaceous materials. (2) is composed of the following three subjects: composition gradient film formation technology, complicated shape film formation/micro-processing technology, and large area film formation. These three subjects were studied to positively make use of characteristics such as low friction/low abrasion and high temperature corrosion resistance which can be expected in amorphous carbon, diamond and high functional carbon materials of carbon nitride and to apply them to moving parts of various industrial machines and surface protection of construction materials such as glass, etc. (NEDO)

FY 1998 report on the project for development of hot water utilizing power generating plants and others, supported by New Sunshine Project. Development of extraction technologies and development of production technologies for the deep-seated geothermal resources; 1998 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 results of the activities for development of extraction and production technologies for the deep-seated geothermal resources, which are expected to contribute to increased geothermal power generation capacity. The program for the PTSD logging technology connects the S probe to PT probe, to simultaneously measure temperature, pressure and volumetric flow, producing the data of good quality even in a high temperature environment over 327 degrees C. Thus, possibility of the commercial system is confirmed. The D probe also produces a density calibration curve showing very good linearity, and operates normally in a high temperature environment of 406 degrees C. The program for the PTC monitoring technology conducts the field tests at Larderello, Italy, to confirm the sampler functions in a high temperature environment. The program for the tracer monitoring technology extracts promising tracers stable at high temperature from those for the liquid, vapor and liquid/vapor mixed phases. Silica is observed to be massively dissolved at 400 to 1,000mg/kg in the fluid under deep geothermal conditions. Scale precipitation rate is minimal for the first 21 days, but increases linearly with time thereafter. The experiments are also conducted for formation and prevention of the Fe-Si-based scales during the flushing period. (NEDO)

FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of production technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen seisan gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For making effective/economical collection of deep geothermal resources, development was made from FY 1991 to FY 2001 of the 'drilling technology for deep geothermal resources' and 'production technology for deep geothermal resources,' and the results were summarized. As to the development of logging technology, the PTSD logging system was developed which can measure temperature/pressure/flow velocity/fluid density in geothermal well under the environment of temperature of 400 degrees C. Concerning the development of monitoring technology, development was made of the PT monitoring system that can make the long-term continuous measuring of temperature/pressure in deep geothermal observation well under the environment of temperature of 400 degrees C and of the C monitoring system that samples geothermal fluids at regular intervals to grasp changes in chemical component. Relating to the development of high temperature tracer monitoring technology, the following were conducted: extraction of high temperature tracer agent that can be used in geothermal reservoirs under the environment of temperature of 300 degrees C, development of simulator, and establishment of how to put tracer agent into the reservoir and how to analyze tracer agent. Further, the R and D were made of scale monitoring technology and scale prevention/removal technology. (NEDO)

FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (Development of technologies for rational use of energy); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, as part of development of technologies for rational use of energy. The program for development of health monitoring technologies produces the bright prospects for commercialization of the fine FBG (Fiber Bragg Grating) sensor which can be embedded in a CFRP prepreg, and establishes the crack detecting method. The program for development of smart manufacturing technologies describes the dielectric constant sensor capable of monitoring the curing process, detection of the cured conditions by the optical fiber sensor, and development of the performs by RTM (Resin Transfer Molding). The program for technological development of the active-adaptive structures conducts the vibration- and noise-controlling tests for the small-size structural elements, confirming that the damping coefficient is improved by at least 20% and acoustic power is reduced by at least 30%. The program for developing the actuator materials and elements improves the piezoelectric characteristics of the PZT-based materials by hybrid sintering, and develops the actuators of high-durability FGM (Function-Gradient Materials). It also develops the foil- and belt-shaped shape memory alloys by arc-aided dissolution and rapid solidification of Ti-Ni-Cu-based alloys. (NEDO)

Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems (Development of practical technology for rational use of energy); 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of development of intelligent material/structure systems, study was made on practical technology for rational use of energy. For resource saving and energy saving (smartening) for large and complex machines and structure systems, light-weight long-life materials/structures are indispensable. Study was thus made on the basic technology of material/structure systems equipped with realtime defect detection function, structural integrity diagnosis function and control function of noise and vibration through information processing and control by integrating composite material/structure and fiber or film sensor material/device. For development of smartening technology, sensing technology was studied to detect the interior structure of composite material/structure compacts. The basic fabrication technology of ceramic actuator materials/devices, and shape memory alloy system actuators were put into development. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends for forming common knowledge. (NEDO)

FY 1991 Report on the results of the research and development of the processing technologies for creating advanced functions. Development of the technologies for preventing corrosion of oil production systems; 1991 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

The research and development project has been started to develop the technologies for superhigh-purity separation/processing; controlling ultrafine crystal particles, including creating composites by the aid of a plasma laser; synthesizing highly functional organic materials; and supporting these technologies, for creating functions, e.g., advanced sensing functions, highly functional electromagnetic characteristics, and corrosion resistance, heat resistance and high strength. The R and D program for the technologies for superhigh-purity separation/processing covers development of highly corrosion-resistant, high-sensitivity gas sensors and highly functional thin oxide film sensors. The R and D program for controlling ultrafine crystal particles covers the researches on the technologies for creating inclined structures by the ion composite vapor-phase process, and the technologies for producing composites by the aid of a plasma laser. The R and D program for the organic material synthesis technologies includes researches on the technologies for controlling higher structures in a molecular beam composite reaction field, and on the technologies for synthesizing materials in a photon composite reaction field and in an interfacial composite reaction field. The R and D program for the supporting technologies includes the researches on the technologies for diagnosing a composite reaction field by the laser-aided ionization method. In the FY 1991, which is essentially the first year for the project, the efforts are directed to designs and construction of the required facilities, and preliminary tests. (NEDO)

FY 1991 report on the results of the contract R and D of the human sense measuring application technology. 4. R and D of correlation/evaluation technology (2); 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu seika hokokusho. 4. Sokan hyoka gijutsu no kekyu kaihatsu (2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

As a part of the correlation/evaluation technology, the following were conducted in this R and D. (1) R and D of space-type human interface adaptable to human sense; (2) R and D of human comfortmeter; (3) research on non-contact skin temperature measuring technology; (4) research on measuring technology of stress indicator material, and technology to relax stress using fragrance. In (1), conducted were the development of space-type human interface, study on the correlation between the visual operating environment and the mental work load/working efficiency, and development of acceleration heartbeat meter. In (2), the basic element experiment was conducted to clarify the basic concept of human comfortmeter, and the basic specifications were made clear. In (3), the experiment using person to be tested was studied to know face skin surface temperature distribution patterns, and correlations between quantity of senses such as thermal/cold senses, concentration, strain and relaxation and mental quantity. In (4), the most important subject is preparation of the environment suitable for the development of new experimental process and device/software. Therefore, the preparation was made considering listing-up of the expected experimental items, selection of common elements, systematization of hardware, establishment of rules of the experimental process, etc. (NEDO)

Report on results for fiscal 1997 (B edition) on development of coal liquefaction technology. Development of bituminous coal liquefaction technology (research by pilot plant) 1/2; 1997 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu) 2/2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

This paper reports the operation of a pilot plant of a bituminous coal liquefaction technology as the 1/2 report. The operation research of the Run-2 through the Run-4-2 was conducted using, as the material, tanitoharum coal which is operating basis coal. The Run-2 achieved a coal charging continuous operation for 42 days. During the operation of 80% slurry supply load, various data were obtained including material balance under the NEDOL standard liquefaction conditions, with a liquefaction yield of 54% daf coal achieved. Steam blowing into the heating tube was found effective as measures to cope with coking generation in the heating furnace of a vacuum distillation tower. The softening point of liquefaction residuals was improved to 178 degrees C through the extracting adjustment of reduced pressure heavy gravity light oil fraction for washing. The Run-3/4-1 achieved a plant load ratio of 100% and a long-term coal charging continuous operation for 80 days, while the Run-3 achieved a slurry supply load of 100% under the NEDOL standard liquefaction conditions. The Run-4-1 achieved a high liquefaction yield of 58wt% daf coal. Performance was confirmed of a neutron beam source irradiation apparatus/measuring system and a tracer injection equipment. (NEDO)

Fiscal 1992 survey report of R and D on new forming technology of composite material. Development of innovative technology for producing members for high efficiency power generation; 1992 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (kokoritsu hatsuden'yo buzai soseigijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

Composite forming technology is being developed which is intended to manifest superplasticity phenomenon of ceramic matrix and metallic matrix composite materials; also being developed is an effective efficient superplastic processing technology which utilizes this composite forming technology. The related technologies were investigated comprehensively systematically with the purpose of promoting the development. First, an overview was given in the present state and problems of ceramic matrix/metallic matrix composite technologies and in the forefront of the superplasticity research of ceramic matrix materials, and then, the related technologies of these composite materials were pigeonholed under the following items: 1. assesment/strength/dynamic properties, 2. composite process and property, 3. composite forming process, 4. superplasticity, 5. process and superplasticity, and 6. others. The titles of the rearranged summary documents are, for example, surface modification and casting of SiC platelets in Al{sub 2}O{sub 3} composites, deformation of Al{sub 2}O{sub 3}/TiC composites at elevated temperatures, superplastic bulging of fine-grained zirconia, forging of short alumina fiber reinforced aluminum alloy, and on superplasticity in silicon carbide reinforced aluminum composites. (NEDO)

FY 2000 report on the results of the R and D of the immediately effective/innovative energy technology. Development of the regenerative technology of energy saving type metal dust; 2000 nendo sokkoteki kakushinteki energy gijutsu kenkyu kaihatsu seika hokokusho. Sho energy gata kinzoku dust kaisei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The development was proceeded with of the technology to recover iron and zinc components directly from high temperature exhaust gas emitted from the steel-making use electric furnace, etc. This process is more simplified than the conventional dust treatment process and markedly reduces the energy needed for zinc recovery. In FY 2000, the following were carried out: 1) development of the element technology to recover metal components in high temperature exhaust gas; 2) development of the technology to optimize the recovery process for metal components in high temperature exhaust gas. In 1), the following were proceeded with: grasp of conditions for metal recovery; development of the equipment to select/separate low vapor-pressure metal components; development of the heavy metal separation equipment to select/condensate zinc. As to the development of the equipment to select/separate low vapor-pressure metal components, it was confirmed by the element test that it was possible to separate iron by carbon material filter. Further, the reaction amount of gasification of carbon material was estimated to be small by the element test and simulational calculation. In 2), the bench-scale test device and small pilot test device were designed/fabricated. (NEDO)

Achievement report for fiscal 1998. Research and development of ultimate atom/molecule manipulating technologies (Development of technology for formation of advanced function materials for use under power generation environment); 1998 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to establish atom/molecule observing and manipulating technologies commonly applicable as basic technologies to industrial fields of new materials, electronics, biotechnology, chemistry, etc. The technologies to be established involve atom level observation and manipulation by mechanically probing into organic molecules such as those of solid surface DNA, microstructure formation with atoms arbitrarily arranged by use of a microfine electron beam and surface chemical properties, simulation by the first principle calculation for the theoretical prediction atom/mole surface application in a process, and new materials to replace semiconductors. The subjects of research and development selected for this fiscal year are the study of silicon nanostructure formation and physical properties, study of nanostructure formation technology based on cluster manipulation, study of nanostructure formation processes using chemical reaction control and local structure analysis, study of new properties of correlation-intensive electron based new materials, study of spin measuring technology, and the study of theoretical analysis of atom/molecule dynamic processes. (NEDO)

Achievement report for fiscal 1999 on development of technology to promote reduction of discharge of dioxins. Development of technology to reduce discharge of dioxins in steel manufacturing processes; 1999 nendo dioxin rui haishutsu sakugen sokushin gijutsu kaihatsu seika hokokusho. Seiko kotei ni okeru dioxin rui haishutsu sakugen gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development has been performed on a scrap melting process to make dioxins emission concentration to 0.2 ng-TEQ/Nm{sup 3} or less in steel making electric furnaces. The testing facility is of semi-sealed structure, consisting of an arc dissolution furnace, an exhaust gas combustion section, an auxiliary combustion chamber, and a quenching chamber. In the arc dissolution chamber, oxygen and coke are blown in at the same time as turning the arc power supply on, and then secondary combustion air was blown in to burn carbon monoxide gas generated from steel melting. The temperature was raised to about 850 degrees C at which dioxins are decomposed in the auxiliary combustion chamber, and then quenched to 200 degrees C or lower in the quenching chamber to prevent recombination of dioxins. As a result of the test, the exhaust gas temperature after the combustion was estimated to have reached about 900 degrees C at which dioxins are decomposed. In addition, because it was possible to control the exhaust gas temperature at the outlet of the auxiliary combustion chamber to about 850 degrees C and the exhaust gas temperature at the outlet of the quenching chamber to 200 degrees C or lower, the dioxins concentration at the outlet of the quenching chamber was reduced successfully to the targeted value or lower. (NEDO)

FY 1992 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1992 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

The paper described the FY 1992 results of the technology to create high efficiency power generation use members. To enhance characteristics of super-high property permanent magnet up to the theoretical level, the development was proposed of a technology to control the size/configuration of micro crystal phase in association with the crystallization of alloy amorphous. For the development of environmental purification use high functional catalysts, a refining method using laser excitation was studied. The observation was also made of molecular adsorption on the Pd thin film catalyst prepared by RF sputtering. The multi-source excitation plasma CVD was proposed which was film-formed by exciting plasma as raw gas independently for each component and supplying it to the substrate of which the periphery was separately controlled. The paper also described the development of technology for ion/light combined assist ultra-thin film production for development of gas turbine combustion sensor. The study was also made of the synthesis of higher-order structure controlled high functional organic materials using the electrode interface combined field which is composed of electrode reaction/high grade photon/extreme magnetic field. In the development of the higher-order structure control technology using the photon combined reaction field, studies were made of the photo reaction film formation technology, the basic film formation technology in the combined reaction field, and the molecular orientation technology. (NEDO)

Fiscal 1996 report on the results of the R and D of technology of high-level treatment/effective use of domestic/industrial wastes, etc. (for public); 1996 nendo Shin Energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku seikatsu sangyo haikibutsu shori yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of reducing environmental loads of waste and effectively using resource by waste recycling, a study was conducted of high-level treatment/effective use technology for domestic/industrial wastes, etc. The paper reported the results of fiscal 1996. In the EcoCement producing technology using the synthetic urban type waste, EcoCement with stable quality was obtained using sewage sludge and industrial waste as raw materials. In the specified freon decomposition disposal technology, an experiment was carried out on durability, etc. of the processing unit. In the high speed/reduced smell biological garbage disposal technology, technology of fermenting disposal, etc. were established, and at the same time technology of making garbage compost was developed. In the technology to manufacture environment friendly type plastic containers, etc., a degradation behavior was grasped of degradable plastics in the compost. In the spread type waste plastic/thermal recycle technology, studied were a system to collect waste and a system to make waste solid fuel. Technology to recycle coolant freon was studied. 14 refs., 261 figs., 137 tabs.

Report on fiscal 1998 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (R and D on carbon-based high function material); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Results of R and D for the initial year were compiled concerning the frontier carbon technology R and D project started in fiscal 1998. In the material formation and evaluation studies of SAW (surface acoustic wave) elements, an AlN (aluminum nitride) film and a diamond/Si film were successfully formed by a nitrogen radical assisted pulsed laser vapor deposition method and a reactive DC magnetron sputtering method. Also performed were the simulation analysis of diamond SAW element characteristics and the evaluation studies of the SAW elements. In the development of the film forming and evaluation technologies of ultra thin carbon-based protective film, carbon-based thin films were developed using an ECR (electron-cyclotron resonance) sputtering method. In the development of evaluation technology for the abrasion performance of ultra thin carbon-based protective films, examination and experiment were carried out for the evaluation device and method capable of simulating abrasion performance in an HDD (hard disk drive). In the development of a high performance display device using a carbon nano tube cold cathode electron source, the evaluation of electron emission characteristics was conducted, as was the manufacturing of a RGB surface light source. (NEDO)

FY 1993 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1993 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The paper described the FY 1993 results of the technology to create high efficiency power generation use members. A processing method was proposed in which to manifest magnetic characteristics up to the theoretical value level, crystallization of magnetic alloy amorphous was controlled and size/configuration of precipitated micro-fine crystals are made ideal. For the development of environmental purification use high functional catalysts, experiments were conducted on the heightening of purity of materials. Namely, by the two wavelength two stage excitation method using color laser, atomic beams of the material metal emitted by electronic beam evaporating source are photo-excited up near the ionization level. These are separated from the non-ionized components by electrostatic field application, and only the ionized atoms are vapor-deposited on substrate. The separation accuracy was good. Plasma excitation of raw gas was done independently for every component, and the multi-source excitation plasma CVD was proposed which is film-formed on the substrate of which the periphery was separately controlled. The synthesis method was considered of higher-order structure control high functional organic materials which are composed of electrode reaction/high grade photon/extreme magnetic field. Study was made of complex reaction field application film-forming/molecular orientation technology using a small test device. (NEDO)

FY 1991 report on the results of the contract R and D of the human sense measuring application technology. 4. R and D of correlation/evaluation technology (1); 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu seika hokokusho. 4. Sokan hyoka gijutsu no kenkyu kaihatsu (1)

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

As a part of the R and D of correlation/evaluation technology, the following R and D were conducted in this paper: (1) high accuracy real sense visual recognition; (2) working environment at nuclear power plant with human sense and affinity; (3) amenity correlation technology in the combined environment mainly of thermal environment. In (1), the following seven items were studied: software for high accuracy real sense visual recognition; software for detecting contact of human movement with object, etc.; improvement of performance of speed of CG image indicator; harmony between image expression and video presentation; software technology for high speed modeling; measuring system under the virtual reality; production of a set of prototype system. In (2), as the environment of nuclear power plant site, visual environment of centralized control room; audio-environment of machinery room, etc., and radio-environment; environment where people have to put on special working ware, etc. In (3), development of a system to examine correlations among external stimulus environment/physiological effect/sensory quantity based on physiological reaction models; development of technology to quantitatively estimate amenity in the combined environment mainly of thermal environment. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 4. Research and development of a correlation and evaluation technology (Part 2); 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the correlation and evaluation technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. In the comfort correlation in a composite environment composed mainly of warm heat environment, the experiment environment was improved, and collection was performed on basic data (cardiac blood vessel and respiration systems) required for developing a system to investigate correlation among external stimulating environment, physiological effect and sense volume based on a physiological reaction model. In evaluating the composite environment comfort, development and improvement were given on component technologies to present experimental environment for warm heat, light beam, and sound. In a space-type human interface system that adapts to human senses, the prototype system of a development platform was completed of mounting as much as half based on the basic design. Discussions were given on findings in computer inputs of eyeball movement information, and on correlation measurement of factors for visual sense operation environment affecting mental burden feeling. With regard to the human comfort meter, satisfactory result was obtained on developing structures for warm heat feeling elements and a control system for the whole body integration, and on defining the detailed specifications. However, designing of a comfort determining software has not achieved the target. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 2. Research and development of physiological effect measuring technology (Part 1); 1993 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Development in fiscal 1993 of a composite physiological function measurement method to measure stresses included the development of a watch type device using the tri-electrode double-point simultaneous measuring method for skin impedance, and a device placed around a head as a blinking meter using the simplified potential method. Both were reduced largely in size and weight. They were verified to have good performance by the measurement performance experiments. For noncontact skin temperature measurement, a noncontact temperature measuring system will be developed that automatically tracks movement of the head of a human body which moves within a limited area, and continuously measure temperatures of specific positions with measurement resolution of 0.2 degree C. Image processing utilizing sensor fusion of infrared and visible images was used to have extracted successfully persons under the natural background. A technology was developed to recognize specific portions of a face (eyes and eyebrows). Developments were made on an algorithm to measure directions of a head, and an attitude controlling and measuring system using a magnetic sensor. In measuring stress index materials, a prospect was obtained to realize semi-macro measurement by collecting cortisol and catecholamine from saliva. Discussions were also given on detecting catecholamine in urine by using high-speed liquid chromatography. (NEDO)

Fiscal 1992 survey report of R and D on new forming technology of composite material. Development of innovative technology for producing members for high efficiency power generation; 1992 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (kokoritsu hatsuden'yo buzai soseigijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

Composite forming technology is being developed which is intended to manifest superplasticity phenomenon of ceramic matrix and metallic matrix composite materials; also being developed is an effective efficient superplastic processing technology which utilizes this composite forming technology. The related technologies were investigated comprehensively systematically with the purpose of promoting the development. First, an overview was given in the present state and problems of ceramic matrix/metallic matrix composite technologies and in the forefront of the superplasticity research of ceramic matrix materials, and then, the related technologies of these composite materials were pigeonholed under the following items: 1. assesment/strength/dynamic properties, 2. composite process and property, 3. composite forming process, 4. superplasticity, 5. process and superplasticity, and 6. others. The titles of the rearranged summary documents are, for example, surface modification and casting of SiC platelets in Al{sub 2}O{sub 3} composites, deformation of Al{sub 2}O{sub 3}/TiC composites at elevated temperatures, superplastic bulging of fine-grained zirconia, forging of short alumina fiber reinforced aluminum alloy, and on superplasticity in silicon carbide reinforced aluminum composites. (NEDO)

Report on results for fiscal 1997 (B edition) on development of coal liquefaction technology. Development of bituminous coal liquefaction technology (research by pilot plant) 1/2; 1997 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B gan). Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu) 1/2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

Through the design, construction and operation of a pilot plant, the NEDOL method was verified, with its operation technology established, and also with a target set in collecting and accumulating data and knowledge required for a commercial plant in the future. With the Run-2, 3, 4 implemented using operating basis coal as the material, the operating stability of equipment/machines was confirmed, and a method of obtaining material balance as well as the operation technology was established, thereby demonstrating the NEDOL process, proving a long-term continuous operability and verifying the highest liquefaction yield. In addition, various process data, engineering data, operation control data, etc., were acquired, classified and analyzed. In the Run-3/4-1, a long-term coal charging continuous operation for 80 days was achieved, as was a high liquefaction yield of 58%. Moreover, data of material balance and thermal balance were obtained, with the performance confirmed of various kinds of equipment. Using the operating basis coat as the material, the coal charging operation of the Run-4-2 was commenced, with the performance verification test carried out for a neutron attenuation tracer method (NAT method), for the purpose of obtaining data of the flow characteristics of the liquefaction reaction tower. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 2. Research and development of a physiological effect measuring technology (Part 1); 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the physiological effect measuring technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. In the composite physiological function measuring technology to measure stresses, improvement was made on the skin impedance measuring device of tri-electrode double-point simultaneous measuring type. A non-contact measuring device using a light sensor was developed as a spontaneous blinking detecting system. A prototype device that can measure blood pressure continuously at the temple was developed, and its usefulness was verified. In non-contact skin temperature measurement, expansion was performed on the image input type visible camera, infrared ray camera and other systems produced to date, and hardware structuring was completed. For the software, person extracting, position recognizing and attitude determining algorithms were developed, whose effectiveness was verified experimentally. A prospect was reached that in measuring stress indexing substances, the measurement can be performed non-invasively using small amount of saliva and urine. The sensitivity was enhanced 20 to 5000 times in catecholamine, and ten times in corticosteroid as much as that in the previous year. It is estimated that on-line measurement may be executed on cortisol by using saliva sample of 100 to 200 {mu} L. (NEDO)

FY 1992 Report on results of the research and development of the technologies for forming composite materials. Development of the technologies for creating parts for high-efficiency power generation systems; 1992 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This project is aimed at development of the technologies for producing ceramic- and metal-based composite materials, and also technologies for superplastic processing by utilizing the phenomenon of superplasticity. The methods studied for development of the ceramic-based composites include casting and powder-utilizing forming at low temperature, and melt forming at high temperature. Those for the metal-based composites include melting at normal and high pressure, powder metallurgy type mechanical alloying and alkoxide methods. The composites studied for development of the superplastic processing are the whisker- and particle-reinforced ones. The composite reinforced with silicon nitride/SiC whiskers is found to be electrophoretically cast to have a bending strength of 497MPa at 1,250 degrees C. The parts of simple shape, e.g., rod and disk, having the target strength are produced by isostatically pressing at normal temperature and high pressure (CIP) and subsequently firing the granules, produced by spray drying the TiC particle/alumina-based slurry. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 4. Research and development of a correlation and evaluation technology (Part 1); 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the correlation and evaluation technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. In evaluating the warm heat comfort by living scenes of workers according to the human body thermal model, the research environment was improved by expanding the systems to measure physiological volume and the warm heat environment. Findings were acquired on the relationship between body fat rate and skin temperature, and actions of artery-vein anastomosed (AVA) blood vessels. These findings were incorporated into the research to elevate the levels of applicability of the human body thermal model. In estimating the sense volume by using skin temperatures, physiological volume being the factor of variation in face skin temperatures was elucidated, and a system to measure these variations was structured. In order to acquire the physiological volume being the factor of variation in face skin temperatures, brain wave topography measurement and {alpha} frequency fluctuation and arousal evaluation and measurement were experimented, where the effectiveness thereof was verified. Analysis was also made on blood flow rate and perspiration volume related to skin temperature variation mechanism, which has provided a number of fundamental data. For the stress measuring technology, and stress relaxation by means of scent, researches were moved forward mainly on environment improvement and preliminary discussions. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 2. Research and development of physiological effect measuring technology (Part 2); 1993 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The high-sensitivity brain wave measuring device has been given improvements in the simplified device net type brain wave sensor that has been improved in fiscal 1993, eliminating the steamy feeling in the head, giving better fitting feeling, and having cleared the target. The multiple application telemeter had the stability enhanced, making it possible to measure living organism signals such as electromyogram, electrocardiogram, eyeball movements, and respiration. To measure living organism activity and rhythm, development was made on a method to evaluate these subjects by using substitution characteristics with development of a portable monitor kept in mind. Measurement and evaluation methods were prepared on the living organism activity from the comparison of the autonomic nervous system activity derived from continuous measurement of pulse cycles with the change in spectra in the {alpha} brain wave. An intestinum rectum temperature correction filter using the number of pulses was fabricated to introduce a body temperature rhythm curve excluded of effects of the body activity. The living organism activity was evaluated comprehensively from the contrast between the daily activity variation and the circadian rhythm. Improvement of accuracy of the tympanum temperature sensor was also discussed. In developing the accelerated pulse meter, the size of the transmitter was reduced, a filter was developed to reduce obstruction signals contained in the signals, and development was begun on a personal computer based system. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 2. Research and development of a physiological effect measuring technology (Part 2); 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the physiological effect measuring technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. Primary prototype fabrication and evaluation were given on an easy-to-mount high-sensitivity brain wave measuring instrument. The multiple application telemeter has come close to completion excepting the integration. For multi-point brain wave measurement, analyzing device interface was completed. In measuring living organism activity and rhythm, development was made on an evaluation method that uses substituting characteristics, with a portable monitor kept in mind. The activity generated by power spectrum change in the {alpha} brain wave was compared with that in the autonomic nervous system to derive the mutual relationship therein, whereas usefulness of the pulse cycle characteristics was verified. Development was made on a method to measure and analyze the tympanum temperature rhythm that corresponds to the intestinum rectum rhythm, and the tympanum temperature was measured discretely by using an infrared sensor. Verification was given on the correlation between the circadian rhythm derived from the intestinum rectum temperature and that derived from the discrete measurement. In developing a nonrestraind accelerated pulse meter, a transmitter of the small accelerated pulse meter that can measure pulses under non-invasive and nonrestraint condition was fabricated on a trial basis, whose easiness of mounting and possibility of signal transmission were demonstrated. (NEDO)

FY 1998 report on the R and D of the industrial science technology. R and D of synergy ceramics; 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Hazardous ingredients in gases exhausted from diesel, refuse treatment facilities, etc. are becoming the problem. The development is expected of porous ceramic films which have functions of separation/purification at high temperature. By making good use of the technology to synthesize ceramic films with uniform through pores of several ten nm order and the technology to form 1D through pores of several ten - 100{mu} m order, the development of the following technologies were made and are in sight: enhancement of functions of gas separation/purification, function of catalyst-carrying to be given, porous film formation/base material fabrication. For the commercialization of high performance structure use ceramic parts, required is innovation of the production method by which the production cost is reduced without damaging the characteristics. Technologies were used of micro-fine raw materials, rapid sintering, texture assessment, analysis, etc., and study was made of cost reduction in high performance ceramic parts. For energy conservation by reducing the sintering temperature, the following were trially conducted: mechanical ironing, use of low grade raw material, use of superplastic reformation and forging, etc. (NEDO)

Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (interim report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

Development was made on a technology to evaluate quality of composite materials. Few data are available for environmental resistance of composite materials, whereas identification of environmental deterioration behavior and establishment of a environmental resistance evaluating technology are a significant issue in utilizing these materials as new materials for space, aeronautics, and marine applications in the future. The present research was taken up with objectives to elucidate deterioration behavior of composite materials exposed to special environment in the atmosphere and space and to establish methods for acceleration tests and environmental performance evaluation by using simulated environments equivalent to the natural environment exposure. The former period (fiscal 1982 through 1984) has investigated environmental conditions in the atmosphere and space, prepared standard test specimens, performed design on environmental devices simulating the environmental elements, as well as tests on deterioration due to environmental elements, and systematized the deterioration characteristics to establish composite test conditions. The latter period (fiscal 1985 through 1988) has developed the composite environment testing device based on the result achieved in the former period, elucidated the deterioration behavior under the composite environmental conditions, and performed evaluation tests on the developed composite materials (FRP). (NEDO)

FY 1998 result report. Research/development on the energy overall development/utilization technology of gas hydrate resource; 1998 nendo seika hokokusho. Gas haidoreto shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This study is aimed at studying for survey of gas hydrate (GH) deposit required for GH resource development and gathering of it, and further at studying for industrial utilization technology development of GH which is different in formation condition depending on kind of gas with which it reacts. The results of FY 1998 are as follows. In the study of the situation of existence of gas hydrate in the tundra, the sedimentary environment of the tundra where natural gas hydrate exists was simulated in laboratory to measure thermal conductivity of the sediments including GH. In this fiscal year, design/fabrication/calibration were conducted of the GH synthesizer and thermal analyzer. In the study of GH gathering technology in the tundra, a technology is discussed for recovering gas from GH layer and at the same time substituting CO2 hydrate for GH by blowing CO2 into the geologic layer. In FY 1998, formation/dissociation behaviors were first studied of methane/CO2 mixture hydrate. For the overall energy development of GH resource and promotion of R and D of the utilization technology, studies were made on physical properties of GH and development of the usage. (NEDO)

Research and development of peripheral technology for photovoltaic power systems. Study of nickel-hydride storage battery for photovoltaic generation systems; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo suiso denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of nickel-hydride storage battery for photovoltaic generation systems in fiscal 1994. (1) On the study on low-cost electrode materials, the physical properties and electrode characteristics were studied of the prototype hydrogen absorbing alloys prepared by substituting Cu or Ni for Co in Mm(Ni-Co-Mn-Al)5 (Mm: mixture of rare earth elements). The result clarified that it is difficult to reduce Co content in the alloy to 0.4 atom or less. Simple heat treatment and milling processes in production of hydrogen absorbing alloy electrodes were achieved by adopting an improved metal mold and gas atomization method. Characteristics and cycle life of the Ni positive electrode prepared by applying active paste material of Ni(OH)2 were studied, however, the result showed only lives of nearly 300 cycles. (2) On the study on electrode structure for high-performance (long-life) battery, the 3-D porous metal electrode support was evaluated, and various battery configurations were studied. 11 figs., 1 tab.

Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

Japanese guideline for the oncology FDG-PET/CT data acquisition protocol. Synopsis of Version 2.0

International Nuclear Information System (INIS)

Fukukita, Hiroyoshi; Suzuki, Kazufumi; Matsumoto, Keiichi; Terauchi, Takashi; Shimada, Naoki; Daisaki, Hiromitsu; Ikari, Yasuhiko; Senda, Michio

2014-01-01

This synopsis outlines the Japanese guideline Version 2.0 for the data acquisition protocol of oncology FDG-PET/CT scans that was created by a joint task force of the Japanese Society of Nuclear Medicine Technology, the Japanese Society of Nuclear Medicine and the Japanese Council of PET Imaging, and was published in Kakuigaku-Gijutsu 2013; 33:377-420 in Japanese. The guideline aims at standardizing the PET image quality among PET centers and different PET camera models by providing criteria for the IEC body phantom image quality as well as for the patient PET image quality based on the noise equivalent count (NEC), NEC density and liver signal-to-noise ratio, so that the appropriate scanning parameters can be determined for each PET camera. This Version 2.0 covers issues that were not focused on in Version 1.0, including the accuracy of the standardized uptake value (SUV), effect of body size together with adjustment of scanning duration, and time-of-flight (TOF) reconstruction technique. Version 2.0 also presents data acquired with new PET camera models that were not tested in Version 1.0. Reference values for physical indicators of phantom image quality have been updated as well. (author)

Technical development of cost-efficient installation of power distribution cables under pavements. Haiden chichuka ni okeru doboku kensetsu gorika gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kokusho, Koji; Kataoka, Tetsuyuki; Tanaka, Yasuyuki; Yoshida, Yasuo; Ikemi, Motoyoshi; Suzuki, Koichi; Kitano, Koichi; Kobayashi, Seiichi; Kanazu, Tsutomu; Komada, Hiroya.

1987-12-01

Various latest technical developments were surveyed for the cost-effective installation of power distribution cables under pavements, and their applicabilities were demonstrated with the evaluation of their cost-reduction effects. Cables in conventional vinyl protection tubes could be buried only 30cm under pavements, and in such case, the cost was reduced to 51% of those of conventional methods. As the results of soil tests, excavated soil over 80% was reusable through coarse screening. Underground radar technique to explore buried pipes from the surface was detectable several pipes buried 1.5-2.0m underground, although some problems in precision were found. The improvement of reinforced concrete man-hole structures to minimize the volume of excavated soil indicated the cost reduction of nearly 20%. The application of these techniques to the installation of cables was expected to ultimately halve the total civil engineering cost. 21 refs., 130 figs., 46 tabs.

Survey on construction of the database for new energy technology development. Cogeneration; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Cogeneration

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As a part of the activity promoting use of new energy, the data related to cogeneration were systematically compiled. For new energy technology, such various policies for introducing new energy are in promotion with a progress of technological development as preparation of subsidy systems, field test business, and support advisory business for introducing new energy. For further effective promotion, integral systematic compilation of various data, and arrangement as basic data are necessary. Such latest announced data in a cogeneration field were collected and compiled as outline of new energy systems, concrete applications, subsidy systems, and approaches to new energy of various countries. Main data items are as follows: trend of cogeneration, outline of system, domestic and foreign concrete applications, prediction data on the use of new energy, overview of domestic and foreign policies for cogeneration, basic terminology, and tables of main related enterprises and organizations. This database is useful for the present activities promoting use of new energy, and preparation of the future vision. 29 figs., 33 tabs.

Fiscal 1993 report on technological results. R and D on micromachine technology; 1993 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-01

Researches on basic element technology of micromachines are conducted with the view of establishing a mechanical system constituted of minute functional elements that perform autonomous operations in a narrow small part of complicated equipment in a power station for example or in a living body. The areas of activity are 1. research on micro actuators and 2. research on basic technology of micromachine; 1 is classified into researches of (1) shape-memory actuator, (2) bending and stretching type actuator, and (3) integrated micro actuator, while 2 is classified into researches of (1) total system for medical diagnosis, (2) micro tactile sensing technology and laser applied diagnosis/treatment technology, and (3) blood pressure/blood circulation sensing technology. In 1-(1), a chemo-mechanical actuator was studied using a shape memory alloy (SMA) and a high polymer gel, and in 1-(2), an SMA and bimetal were employed as a source of the driving force. Further, examination was also made on a fluid driving type actuator. (NEDO)

New energy technology development related database construction survey (wind power generation); Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (furyoku hatsuden)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

To arrange systematic data relating to new energy, the latest published data relating to the wind energy conversion systems have been collected and arranged. For the overview of wind energy conversion system, wind turbines with horizontal axis and vertical axis, specification of wind turbine, and conceptual figure of wind energy conversion systems are illustrated. For the installation examples, introduction development of wind energy conversion systems in the world is described for Japan, the USA, Germany, Denmark, Spain, Sweden, India, and Belgium. For the relevant legislation and support plan, relevant legislation for the introduction of wind energy conversion in Japan, support plan in Japan, and support plans in foreign countries are described. Prices of wind turbines by wind turbine makers in the world, construction cost by Japanese makers, basic term, and subsidiary company and organization are shown

Generation characteristics of photovoltaic power generation equipment at TEPCO R and D center; Gijutsu kaihatsu center taiyoko hatsuden setsubi no hatsuden tokusei

Energy Technology Data Exchange (ETDEWEB)

Amano, K; Natori, K [Tokyo Electric Power Co. Inc., Tokyo (Japan)

1997-11-25

Solar battery arrays are installed at different tilt angles for actual measurement in an experiment conducted by TEPCO (Tokyo Electric Power Company, Inc.) Research and Development Center for the examination of their power generation characteristics. Arrays of polycrystalline silicon solar battery modules are positioned facing a direction +7 degrees swung from the south on the Center rooftop and verandah, and they are installed at tilt angles of 0, 30, 60, and 90 degrees. An analysis of system characteristics is conducted, and findings mentioned below are obtained. In fiscal 1996, the highest utilization factor of a yearly average of 11.3% is attained with the ones tilted at 30 degrees. As for the utilization factors at the other angles, they are 10.2% at 60 degrees, 8.8% at 0 degrees, and 8.0% at 90 degrees. The integrated design coefficient remains approximately constant irrespective of the different tilt angles of 0, 30, and 60 degrees. The overall design coefficient of the 90 degree-tilted array installed on the verandah is found to be 0.75, which is higher than those exhibited by the others. Appropriate routes of wirings for modules should be worked out to avoid the ill effect of the shadows of steel towers. 2 refs., 11 figs.

Fiscal 2000 report on the development of high-efficiency refuse-fueled power generation technology; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu 2000 nendo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to develop a refuse gasification/fusion power generation technology to contribute to the effective utilization of unexploited energy and to reduction in greenhouse gas emissions. Developed in the technology of elevating steam temperature were the evaluation of high-temperature corrosion of SH materials and a high temperature dust removing system, dechlorination technology for the thermolysis process, and a ceramic-made high-temperature air heater. For the avoidance of exhaust gas reheating, development was carried out for a low-temperature denitration unit, stable refuse feeding system for reduction in the self-heat melting critical calorific value, waste plastic injection technology for reduction in the amount of external fuel injection, and so forth. The effect of the developed element technologies were evaluated and a detailed feasibility study was conducted for a refuse gas conversion power generation system using gas engine power generation for minor-scale general waste treatment facilities. In the survey of the trend of refuse-fueled power generation technologies, trend in Japan and advanced refuse-fueled power generation systems and their introduction in Europe and America were investigated. (NEDO)

FY 1995 annual report on the project for promoting development of superhigh electronic techniques; 1995 nendo chosentan denshi gijutsu kaihatsu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

Described herein are the FY 1995 results of the R and D project for developing superfine machining process techniques, measurement/analysis/controlling techniques for extreme conditions, and techniques for electronic materials of new functions, in order to establish the superhigh electronic techniques of two generations beyond. The project is implemented, mainly for the following targets: direct image drawing systems with electron beams by R and D of the techniques for electro-optical systems and superhigh-accuracy controlling techniques therefor; patterning systems with supershort-wavelength electro-magnetic waves by R and D of techniques for X-ray optical systems, superhigh-accuracy controlling techniques therefor and photosensitive process techniques; superfine photosensitive techniques with ultrashort-wavelength laser beams; techniques for superhigh-accuracy light-shielding systems; superhigh techniques for measurement/analysis/controlling of plasma reactions as the bases for plasma-aided superthin film making and superfine etching; basic techniques for superhigh cleaning; techniques for superhigh-sensitivity media; techniques for elements of new functions and making thin films thereof; and techniques for electronic materials of new functions. (NEDO)

Development of the advanced load leveling air conditioning technology utilizing unutilized energy; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A heat supply plant utilizing unutilized energy is called for environment-friendly efficient operation including stable heat supply, energy saving, CO{sub 2} emission control and power load leveling. Toshiba developed the optimum operation system for environment-friendly efficient operation considering heat demand prediction and characteristics of a heat supply plant. The demonstration test result showed that this system is effective to reduce power cost of a heat supply plant by nearly 15%. This system was promoted by joint research of NEDO, Heat Pump and Thermal Storage Technology Center of Japan and Toshiba supported by Agency of Natural Resources and Energy, MITI. (translated by NEDO)

Fiscal 1997 report on the development of new hydrogen atomic energy demonstrative technology; 1997 nendo kenkyu hokokusho (shinsuiso energy jissho gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

In this validation study, phenomena of excess heat which are said to be generated by electrolysis of deuterium using palladium metal, etc. as electrode are taken as `new hydrogen atomic energy,` and to clarify a possibility of using them as a future energy source, the abnormal heating phenomenon was validated and the mechanism was elucidated. The study targeted quantitative control of heat emissions. The study was finished in 1997, the fifth year from the start. The excess heat measurement could partially be reproduced; however, when conducting a confirmation experiment on the excess heat by another more reliable method under the same condition, it was found that the value of excess heat was not an absolute value exceeding measuring sensitivity and errors of the system. If the excess heat of 0.1W order is to be emitted in nuclear reaction, any reactive product should be detected in a substantial quantity. However, the product of a large quantity was not found. A possibility was found out of an increase in nuclear reaction ratio inside solid by low energy deuterium irradiation. From the above, it was concluded that the use of new hydrogen atomic energy was negative. 20 refs., 149 figs., 29 tabs.

FY 2000 research and development on DSRC/ITS application systems for vehicles; 2000 nendo DSRC/ITS shasaiki no oyo gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research and development project aimed at application of the large-capacity, high-speed, bilateral dedicated short-range communication (DSRC) techniques, used for communication between running vehicles for electronic toll collection (ETC), to various types of ITS. The current ETC data alone is useful to apply the tollgate passage histories to the management of the vehicle operation. For practical application of the ETC tollgate passage data by transportation companies, developing the IC card readers installed at their offices and examining methods of interconnecting the DSRC-based vehicle operation management systems and ETC are effective. The field demonstration tests are conducted for DSRC-based onboard ETC equipment in real environments. The standards or guidelines are drafted for the four research items studied for application of DSRC/ITS onboard equipment, based on the onboard system architectures. More concretely, the standard specifications are drafted for the two items of the DSRC-applied platforms and functional diversification of the onboard ITS equipment, and the guidelines are drafted for the other two items of application of the DSRC systems for paying various fees and application of the DSRC systems for vehicle operation management. (NEDO)

Achievement report on the development of solar thermal electric power plant technologies. Annex; Taiyonetsu hatsuden plant gijutsu kaihatsu seika hokokusho. Fuzoku shiryo

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-07-01

The two solar thermal electric power pilot plants are of the tower concentration type and the flat/curved surface concentration type. For the first time in the world, they succeeded in operating at a rated output of 1,000kW in August and September, 1981, respectively. Sunshine was inputted at an unstable rate, and the plants were operated under various load patterns. Studies were conducted and an optimum operating technique is established. Since designing, construction, and operation were carried for two types of pilot plants, quantities of useful data were collected through a variety of experiences. Valuable hints and design data were provided for use in the construction of full-scale power plants in the future. Element units developed for the plants were high-reflectance mirrors, high-precision tracking mechanisms, solar heat collectors of the cavity type and paraboloidal type, and molten salt heat accumulators. The tower concentration type plant exhibits a power generation efficiency of 16-17% and an overall plant efficiency of 3.1-4.4%. The maximum overall efficiency a month is 3.9% with the flat/curved surface concentration type plant. (NEDO)

Outline of research achievement of fiscal 1983. Development of coal liquefaction technologies; Sekitan ekika gijutsu kaihatsu. 1983 nendo kenkyu seika no gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-07-01

Reported are the results of (1) the development of bituminous coal liquefaction technology, (2) development of brown coal liquefaction technology, (3) experimental fabrication and development of plant equipment and materials therefor, and (4) a survey on coal type selection. The goals of the development are mentioned below. Under Item (1), an optimum liquefaction process and a solid/liquid separation process are to be defined, the effect of iron-based catalysts upon liquefaction reaction is to be elucidated, a technology for constructing a direct hydroliquefaction unit is to be established, and a plant using such a unit is to be developed. Under Item (2), an optimum liquefaction technology is to be established, high in economic efficiency and reliability, by subjecting Australia's Victoria brown coal to the direct liquefaction process. In particular, a new brown coal liquefaction technology is to be established, which will be an organic combination of a novel, raw brown coal slurry dehydration technology, a solvent deashing technology, and the secondary hydrogenation technology, all centering on the basic technology of primary hydrogenation. Under Item (3), reactor materials, accessory materials, slurry pumps, etc., are to be experimentally manufactured and developed further. Under Item (4), data are to be collected on coal resources, coal quality, liquefaction characteristics, etc., during the process of technology development for liquefaction, etc. Furthermore, methods are to be established for the effective utilization of liquefaction products and for their optimum refining. (NEDO)

Investigation on the development and introduction of new geothermal exploration technology. Part 2; Chinetsu shintansa gijutsu kaihatsu donyu ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

For the purpose of maintaining and increasing the geothermal power generation amount, the development was made of exploration technologies which become necessary in the stage of geothermal reservoir exploration and in the stage of reservoir management and peripheral development. As development technologies, the following were proposed: fracture flow characteristics exploration method (FE), production/circumference areas flow characteristics exploration method (PE), and integrated analyzing method (IA). As to FE, for the survey of geothermal fluid dynamic characteristics in fracture aggregate composing the geothermal reservoir, developments were made of the well hydraulic testing method for examining hydraulic characteristics of fracture system and of the fracture evaluation method composed of the core/logging analysis method, the permeability logging method and electroseismic exploration method. As to PE, for maintaining and managing steam production in the developmental area and developing the area to the circumference area, development was conducted of technology for exploring variations of reservoirs and fluid flow from the data on precision gravity, three-dimensional resistivity, fluid geochemistry, active seismic wave and self potential, precision electromagnetism, passive seismic wave, etc. As to IA, development was made of reservoir simulation technique, etc. 2 refs., 70 figs., 41 tabs.

Research and development of utilization technology of solar thermal system for industrial and other use. Research and development of key technology (energy conversion on technology using chemical reactions); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Yoso gijutsu no kenkyu (kagaku energy henkan gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for energy conversion technology using chemical reactions by the aid of solar energy. The demonstration runs were conducted by a bench-scale unit, which was operated stably for 100h, to produce promising results. The catalyst exhibits stable performance, without showing a sign of deactivation. It is found that the heat pump system works well, without being interfered with accumulated by-products. A heat of approximately 2,100kcal/h is recovered. It is confirmed that steam of 150{degree}C and 200{degree}C is generated from hot water of 80{degree}C and 95{degree}C, respectively. The bench-scale runs show a thermal efficiency of around 10%, which is lower than the target level. However, the runs with hydrogen-occluding alloy attain a process thermal efficiency of 30%. The system in which solar collector and chemical heat pump units are combined is evaluated with respect to its economic efficiency and operability for its eventual commercialization. 6 figs., 2 tabs.

Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir change prediction technology (Development of modelling support technology); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu (modeling shien gijutsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The aim is to develop and popularize techniques relating to geological information such as thermal history. The efforts center about the application of a now-available core fracture measuring system to developed geothermal fields and about the development of new technologies. The measuring system is applied to some core cuttings collected from five boreholes in the Akinomiya district, Akita Prefecture, and the system is used for (1) the evaluation of homogenization temperatures of inclusions in the fluid, (2) the measurement of the points of melting from ice of inclusions in the fluid, and (3) the implementation of laser Raman spectroscopy. Under item (1), it is found that the minimum homogenization temperature of quartz phenocryst in the mother rock or of low-salinity fluid inclusion in a quartz vein is near the current subsurface temperature and that subsurface and reservoir temperatures may be known by evaluating their homogenization temperature. Under item (2), it is found that the NaCl equivalent salinity is distributed in the range of 0.0 to 25wt% and that, in this connection, there is difference between a fluid in a fluid flow and a fluid spurting as thermal water in the Akinomiya district. Under item (3), CO2, N{sub 2}, and CH{sub 4} are detected in most of the boreholes. Efforts are exerted to develop a hydrothermal fluid analyzing technique using a rapid rock dating method and traces of chemical ingredients in hydrothermal minerals. (NEDO)

Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (CuInSe2 based PV cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (CuInSe2 taiyo denchi seizo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on the fabrication technology of CuInSe2 based PV cell in fiscal 1994. (1) On formation of high-quality CIGS thin films by bilayer method, Mo film was deposited on a glass substrate by sputtering, and CIGS film with different Ga/In ratios was next formed on the substrate by quaternary simultaneous deposition at different In and Ga deposition speeds. In addition, CdS film was deposited on the CIGS film, and ZnO and ITO films were finally deposited on it by sputtering to complete solar cell. This solar cell offered the maximum conversion efficiency among cells using CIGS film. (2) On formation of high-quality CIGS thin films by three-stage method, a certain correlation was found between substrate temperature and CIGS film composition by monitoring substrate temperature in film forming process. This phenomenon allowed rigorous control of CIS film compositions important for CIS thin film solar cells. (3) On low-cost process technology for thin film formation, Cu(In,Ga)S2 solid solution film was fabricated by expanded selenic process. 3 figs.

Fiscal 2000 achievement report on development of high-efficiency high-reliability welding technology through improvement on welding techniques; 2000 nendo yosetsu gijutsu no kodoka ni yoru kokoritsu koshinraisei yosetsu gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-04-01

Efforts are made to develop a welding design support system capable of increasing reliability and enhancing welding efficiency. Activities are conducted in the six fields of (1) the development of welding process simulation models, (2) development of welded section structure simulation models, (3) development of simulation models for predicting welding caused deformation, (4) integration of the models, (5) analysis of the welding phenomenon, and (6) the elucidation of the defect generation mechanism. In field (1), efforts are made to develop an arc plasma model, a molten pool convective heat transportation model, and a welding process model. In the effort to develop an arc plasma model, studies are made about a stationary axisymmetric arc in its steady state and about a constitutive equation and computation algorithm for developing a model in which a tungsten electrode (cathode) and an arc plasma welding pool (anode) are integrated. Furthermore, the simulation outcomes are experimentally verified. Satisfactory models are obtained as far as qualitative properties are concerned. (NEDO)

Technological development report for fiscal 1993 on the woodwaste thermolysis/gasification technology and generated gas utilization technology; 1993 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The project is a joint effort of Japan and the Philippines to develop a thermolysis/gasification system, in which woodwaste now remaining unexploited in the Philippines is subjected to thermolysis/gasification and the resulting gas is used in a gas engine for the generation of electric power, in a 5-year period beginning in fiscal 1990. In this fiscal year, element technology verification tests are conducted, components of a demonstration plant are manufactured, and procurement is made as required, which completes all the tasks allotted to this fiscal year. All the constituents of the said demonstration plant fabricated or procured since fiscal 1991 are packed up and forwarded to Industrial Technology Development Institute (ITDI) of the Philippines, and engineering guidance is extended and test operations are carried out at the site of plant installation. In line with the said endeavors, on-site investigations are performed and researches are conducted together with ITDI scientists concerning the construction work and element technology confirmation. On the other hand, the Philippine side performs the second phase of civil engineering and construction carried over from the first phase. The demonstration plant is completed, adjustment and test operations are carried out, which means that the project is in progress as initially scheduled. (NEDO)

FY 1998 achievement report on the photon measuring/processing technology (R and D of the photon measuring/processing technology); 1998 nendo foton keisoku kako gijutsu seika hokokusho. Foton keisoku kako gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In this project, the survey/arrangement were made of the trend of the recent technology such as photon (laser) measuring/processing/generation and a possibility of adopting the photon technology to the field except measuring/processing, to clarify technical subjects for establishing/commercializing the photon technology. Also for the purpose of reducing the energy cost by improving the performance of laser processing device, prolonging the life and reducing the operational cost, the development of the following were carried out: (1) high efficiency laser processing device. (2) high conversion efficiency laser diode. In (1), a laser generating device with Yb:YAG crystal as oscillating medium was trially manufactured, and the power of 35W and optical-optical conversion efficiency of 7.1% were obtained. A comparison was also made between Yb:YAG laser and Nd:YAG laser, and made it clear that as the industrial use high power laser, Nd:YAG laser has the advantage over the other. In (2), the development was made of technology for simultaneous uniform growth of more than one LD crystal wafers with high conversion efficiency and technology for evaluation. Namely, the high uniformity crystal wafer with variations among wafers of {+-}4% was obtained using the introduced high efficiency crystal growth device and high efficiency thin film evaluation device. (NEDO)

Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of advanced maintenance technology for power plant facilities); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on R and D of measurement technology, laser welding and surface treatment technology, and generation technology of photon beam, for improvement of the quality and maintenance efficiency for power plant facilities. In the study on fabrication of functional micro-composite circuits, the equipment for forming circuits on substrates by carrying particles with gas was developed whose geometric standard deviation is 1.17 for 26nm particles. In the study on gas concentration measurement technology, development of the variable-wavelength laser beam source for measurement, fabrication of thin films by epitaxial growth equipment, and computer simulation of sensitivities for quantum IR photo- detectors were promoted. In the study on photon wavefront compensation device technology, the technology for fabricating such device with (411)A surface orientations and asymmetric quantum well structures was developed. In the study on high-sensitivity detection technology using short- wavelength photon, to develop a high-energy resolution fluorescent X-ray detector, favorable electric properties of superconducting X-ray detecting devices were confirmed at nearly 0.1K. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of new software structuring models (R and D of micromachine cooperative control use software); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Shin software kozoka model no kenkyu kaihatsu (bisho kikai kyocho seigyoyo software no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A R and D was conducted of software structuring models which ease the development and maintenance of software systems and meet diversification of needs. As for the study of the cooperative control use programming language, a R and D of agent oriented language Flage was carried out for expansion of language function, arrangement of network function, development of exercises, etc. As to the formulation of agent knowledge, proposed were processes to make a program from the specifications, and EVA, a mechanism in response to changes in the specifications of existing programs. In relation to the basic theory of cooperation system, a study was made mainly of object oriented attribute grammar OOAG as a model representing cooperative computation in software process as a rule group. Concerning the study of the situation recognition mechanism, researched were models of communication and reasoning among agents in cooperation. 187 refs., 107 figs., 23 tabs.

FY 1999 Report on results of development of high-efficiency energy system technologies for transportation and domestic use. R and D of polymer electrolyte fuel cells, power system technologies, and several kW class domestic power systems operating at normal pressure; 1999 nendo un'yu minseiyo kokoritsu energy system gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, joatsu sadogata su kW kyu kateiyo dengen system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Described herein are the FY 1999 results of the research and development project aimed at development of fuel cell systems for power source systems suitable for domestic use. The programs for development of fuel cell body include improvement of the anode forming method for increasing its CO tolerance, enhancing cell performance at 0.5mg-metal/cm{sup 2} as the catalyst quantity to a level almost comparable to that obtainable at 0.9mg-metal/cm{sup 2}. The programs for development of the fuel supply system include studies on endurance of the elements, e.g., starting-up/shutting-down of the Ru/Al{sub 2}O{sub 3} catalyst, using a microreactor, confirming that it is serviceable for at least 1,000 hours. The natural gas reformer is developed and operated, on a trial basis, achieving stable supply of steam and fuel, and thermal efficiency of 82.7%. The operation researches include development and operation of a 1kW class module, achieving the performance surpassing the FY 1999 targets (average cell voltage: 0.70V, output: 1.27kW) with a simulated reformate gas at an air utilization rate of 20% and current density of 0.3A/cm{sup 2}. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. Separate volume. R and D of the system evaluation technology (Data book on the photovoltaic power system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu (Bessatsu : Taiyoko hatsuden system data shu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of establishing the optimum design and optimum operation technology of various kinds of photovoltaic power system, data were collected to make a data book on various kinds of photovoltaic power system of which the future commercialization is expected. Included in this data book were the monthly report on operation data on demonstrative test facilities at the Hamamatsu site of JQA (Japan Quality Assurance Organization), daily graph of insolation/temperature, monthly graph of wind direction/wind velocity. Further, as the data on the residential use photovoltaic power system, data on the following were summed up: information on the site of installation of the residential use photovoltaic power system (photo information, the state of installation such as sites installed more in FY 2000, drawings of module arrangement and measuring point layout, etc.), daily report on operation (graph of daily trends, daily report by site, hourly report by site, daily report on all sites, hourly report on all sites), operation data and performance indices, list of troubles arising in the residential use photovoltaic power system, other system information about residential use measuring data, power generation characteristics and {alpha}{sub pmax} of residential use solar cell modules, etc. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of environmentally-friendliness enhancement for next-generation solar cell development); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Shuhen yoso gijutsu ni kansuru kenkyu chosa, Jisedai taiyodenchi kaihatsu kankyo tekioka chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Though the trends of solar cell development are becoming increasingly diverse across the world, yet none has emerged to promise a stable solar cell supply in the future. Under the circumstances, studies were conducted to clarify strategies for solar cell technology development which would be well adapted to Japan's social environments, with the trends of development in the United States and European countries taken into consideration. The surveys covered the research and development and diffusion of photovoltaic power generation in the United States and European countries, and their solar cell research and development strategies and trends of development were put together. Surveys were also conducted into the research and development of unconventional types of solar cells, such as the dye-sensitized solar cell, organic solar cell, conjugate polymer solar cell, and the polymer/C{sub 60} based solar cell, and into the status of resources of materials for solar cells such as gallium, arsenic, cadmium, tellurium, indium, selenium, and germanium. Regarding the future of photovoltaic power generation research and development, it was concluded that commercialization technology development and basic research and development should continue. Also pointed out was the importance of the enlargement of the market for photovoltaic power generation systems. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of environmentally-friendliness enhancement for next-generation solar cell development); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Shuhen yoso gijutsu ni kansuru kenkyu chosa, Jisedai taiyodenchi kaihatsu kankyo tekioka chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Though the trends of solar cell development are becoming increasingly diverse across the world, yet none has emerged to promise a stable solar cell supply in the future. Under the circumstances, studies were conducted to clarify strategies for solar cell technology development which would be well adapted to Japan's social environments, with the trends of development in the United States and European countries taken into consideration. The surveys covered the research and development and diffusion of photovoltaic power generation in the United States and European countries, and their solar cell research and development strategies and trends of development were put together. Surveys were also conducted into the research and development of unconventional types of solar cells, such as the dye-sensitized solar cell, organic solar cell, conjugate polymer solar cell, and the polymer/C{sub 60} based solar cell, and into the status of resources of materials for solar cells such as gallium, arsenic, cadmium, tellurium, indium, selenium, and germanium. Regarding the future of photovoltaic power generation research and development, it was concluded that commercialization technology development and basic research and development should continue. Also pointed out was the importance of the enlargement of the market for photovoltaic power generation systems. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Volume 1. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture low-cost large-area modules and survey and research on analyzing how to put products into practical use); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu 1))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to assist research and development to put thin film solar cells for power use into practical use and a research to put thin film solar cell manufacturing technologies into practical use, survey and research have been performed on trends in the technologies inside and outside the country. Characteristic points in thin film solar cells during the current fiscal year include: expansion of production scale of amorphous silicon solar cells, rapid progress in poly-crystalline silicon thin film solar cell technologies, and enhancement of performance in large-area modules in the a-Si, CIGS, and CdTe systems. In the trends in research and development of amorphous systems, expectation is heightening on elucidation of optical deterioration phenomena, and establishment of suppression technologies thereof. Although the highest efficiency was not renewed in thin film solar cells of small areas, progress was seen in the post-stabilization efficiency in large-area modules. A thin film solar cell manufacturing plant having an annual production capacity of 20 MW was put into operation in October in Japan. Micro (poly) crystalline silicon based solar cells have high possibility of being compatible in cost reduction and performance improvement, and energetic researches are being carried out on them in recent years as the most promising candidate of the next generation solar cells. (NEDO)

Research and development of basic technologies for next generation industries, 'high crystalline polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo (dainiki kenkyu kaihatsu kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

This research and development is intended to establish a basic technology related to high crystalline polymeric material that has dynamic properties comparable to metallic materials by single polymeric material as a structural material. Thick and large high-elasticity molded forms were obtained by searching poly-arylate material, and by developing such processing technologies as high-pressure injection molding, composite injection molding, and elongation fluidity molding. High-elasticity molded forms with uniform internal orientation were obtained by heating and molding liquid crystal polymers under high magnetic field. Solution molding was performed on a molecular composite consisting of rigid chains and soft chains, which was laminated and bonded to have obtained an isotropic form with as high elasticity as 54 GPa. In addition, high pressure powder formation of cross-linked polymers of di-acetylene system provided an isotropic form with sound wave elasticity of 23 GPa.

Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (dainiki kenkyu kaihatsu hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The research and development in the second term included development of raw materials, elucidation of electricity conduction mechanism, and development of methods to improve stability and a new processing method. Crystals of a large number of charge migrating complexes were grown to elucidate their electron properties and structures. A theoretical model was structured for the superconduction mechanism in the charge migrating complexes. Poly-p-phenylene vinylene-based polymers achieved {sigma}=1.1 times 10{sup 4}s/cm as a result of extension of soluble reaction intermediates. Poly-2, 5-phenylene vinylene doped with FeCl{sub 3} retained 10{sup 3}s/m for 165 days in nitrogen. Polypyrrole achieved 3.0 times 10{sup 3}s/cm in constant potential electrolytically oxidizing polymerization and extension at low temperatures. Polypyrrole doped with ClO{sub 4}{sup -} retained electric conductivity of 85% for 400 days in nitrogen. Electric conductivity of higher than 10{sup 5}s/cm was obtained by applying different kinds of doping into thin film and fiber formed graphite. The world's highest conductivity of 9 times 10{sup 5}s/cm was achieved particularly with discharge laminated and polymerized graphite doped with AsF{sub 5}. (NEDO)

Development of large scale wind energy conservation system. Development of control techniques for assembly-type wind power generating systems; Ogata furyoku hatsuden system no kaihatsu. Shugogata furyoku hatsuden system no seigyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for development of control techniques for assembly-type wind power generating systems. The study on optimum system configuration produces 50 to 100kW wind power units for screening small-size wind power plant types, and, at the same time, surveys performance of commercial units and experiences of 9 makers capable of producing the above units. As a result, 3 MICON`s units (output: 100kW, active YAW control, monopole tower, maximum wind speed: 60m/s) are selected. The study on optimum operational techniques integrates 2 medium-size power units into a power line, showing a service factor of 30.2% on the annual average, monthly varying in a range from 11.8 to 45.0%. These units, installed in Miyako Island, were attacked by 3 typhoons of wind velocity of 25m/s or higher in 1994, and the only damage recorded is that of the anemoscope/anemometer. It is found that No.1 unit is located at a better geographical point than the No.2 unit, to produce a higher output. 3 figs., 3 tabs.

Research and development of the industrial basic techniques of the next generation. Composite materials (Final research and development evaluation / Part 1); Jisedai dangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (Saishu kenkyu kaihatsu hyoka 1)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

This R and D project is aimed at development of highly functional materials for aerospace devices, bringing into focus research and development of resin-based composite materials (FRPs), metal-based composite materials (FRMs), and evaluation of their properties and their design techniques. The basic target properties are heat resistance temperature of 250 degrees C or higher and tensile strength of 240 kg/mm{sup 2} or more for the FRPs, and heat resistance temperature of 450 degrees C or higher and tensile strength of 150 kgf/mm{sup 2} or more for the FRMs. This R and D program has been implemented for 8 years for development of raw materials, molding/processing techniques, quality evaluation and designs through information exchange and discussions of the experts in each area under integrated, close cooperation from raw materials to molding/processing. Most of the data indicate that the target properties and objects are satisfied or exceeded. It is therefore concluded that this project for the composite materials, extending for 8 years in 3 phases, has sufficiently achieved the initial objects. The unique techniques are incorporated in the raw materials, molding/processing processes, quality evaluation and designs. These efforts have produced the FRPs and FRMs of the world highest qualities. (NEDO)

Research and development of peripheral technology for photovoltaic power systems. Research and development of redox flow battery for photovoltaic power generation; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo redox denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of redox flow battery for photovoltaic power generation in fiscal 1994. (1) On the production method of electrolyte, silica reduction treatment was attempted to use ammonium metavanadate recovered from boiler as electrolyte of redox flow battery. Silica removal rates more than 90% were achieved by crystallizing V as polyvanadate while keeping molten silica. It was ascertained in minicell experiment that trivalent and quadrivalent V electrolytes produced from recovered V are applicable to continuous charge/discharge operation for one week. (2) On development of battery systems, the relation between battery characteristics and physicochemical properties of carbon fiber electrodes was studied to improve carbon fiber electrodes. The efficiency of 80% was achieved at current density of 160mA/cm{sup 2} by use of layered electrodes, resulting in considerable cost reduction. Performance evaluation operation of the 2kW battery prepared in the last fiscal year was also carried out. 4 figs.

Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

Fiscal 1996 report on the R and D result of industrial science and technology. R and D synergy ceramics (R and D on synergy ceramics); 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (synergy ceramics no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper summarizes the general survey mainly conducted by FCRA (Fine Ceramics Research Association) in fiscal 1996, and the joint research results with some universities, from some R and D on synergy ceramics. Silicon nitride based ceramics expressed the same high thermal conductivity as metal by seed crystal addition, grain growth control and orientation control of sheet lamination. For its practical use, study was made on control factors of material, formation and sintering. Ca2Y2Si2O9 single crystal was prepared by float-zone method to determine its crystal structure. No volume change due to high-temperature phase transition as thermal expansion was found. In carbothermal reduction- nitridation of SiO2, addition of Si3N4 seed powder increased a reaction rate and formed uniform particles with an isotropic shape. An average particle size was dependent on the size and number of fine particles in seed powder. Addition of both Si3N4 and Fe compound could change a particle shape from a spherical grain to an elongated grain. A spherical Fe-Si metal grain was found on the tip of an elongated grain. 66 refs., 73 figs., 13 tabs.

FY1998 report on the achievements on the research and development of a quickly effective and innovative energy environment technology, and development of a technology to re-use wastes as resources and fuel; Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu, kanen gomi saishigen nenryoka gijutsu kaihatsu 1998 nendo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With objectives to realize a recycling society and protect global environment, development will be made on solidified fuel using waste papers and waste plastics as the raw materials. This paper describes the achievements in fiscal 1998. To develop a pretreatment technology, analyses and discussions were given on functions required to separate and remove such foreign materials contained in combustible wastes as metals, ceramics, and glasses, and to pulverize the combustibles removed of non-combustible materials. A bench-scale testing equipment of 0.5 ton per hour was installed and operated on a trial basis. In order to identify dechlorination properties of waste papers and plastics to develop a dechlorination technology, basic dechlorination and pyrolysis tests were performed by using cellulose powder and polyvinyl chloride powder as raw materials. Detailed design, fabrication, installation and trial operation were carried out on a dechlorination device to be assembled into the bench-scale testing equipment. Investigations were given on the actual status of discharge and collection of waste papers and plastics to discuss the practical use of the fuel. The current status of discharge of general wastes was identified, which will be the object of the container package recycling law. The range of LCA was discussed, and technical data of wastes electric power generation were collected. (NEDO)

Fiscal 1999 achievement report. Development of technology for reducing power consumption during standby (Research and development of technologies for application of standby power reduction to domestic and office-automation appliances); 1999 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Kaden oyobi OA kiki no taiki denryoku sakugen jitsuyoka gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Efforts are exerted to develop power-efficient modules to be built into electrical products for reduction in power consumption in the standby state for domestic and office-automation appliances. In this study, television sets, audio sets, and air conditioners were selected out of domestic appliances and, out of office-automation appliances, notebook-size and desktop personal computers were selected. The standby power consumption is to be reduced to 3mW for domestic appliances, to 0.2W for notebook-size personal computers, and to 1/10-1/200 of the level being currently consumed in the case of desktop personal computers. For domestic appliances, a power efficient module not insulated from the AC power line was developed, to be built into a CPU-aided appliance to be turned on and off by remote control for the reduction of its standby power to 3mW. For notebook-size personal computers, a power-efficient power source insulated from the AC power line was developed, which consumes but 0.2W of standby power. It was built into a marketed notebook-size personal computer and tested for performance. For desktop personal computers, a 25mW power source insulated from the AC power line was fabricated, and tested for performance. (NEDO)

FY 1993 Report on the technical results. Research and development of extreme handling technologies at atomic/molecular levels (Development of technologies for forming highly functional stock materials for power generation environments); 1993 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This research and development project is aimed at development of the technologies for observing/handling solid surfaces and organic molecules at the atomic level by the mechanical probe; forming the fine structures of optional atomic sequences using fine electron beams and surface chemical characteristics; simulation by the first principle calculation to theoretically predict the atom/molecule surface reactions in a process; and producing new materials substitutes for semiconductors, in order to develop the atom/molecule observing and handling technologies as the common basic technologies for the various industrial areas, e.g., new materials, electronics, biotechnology and chemical. The research/survey activities are directed to (1) development of the technologies for observing the atoms and molecules on solid surfaces, (2) development of technologies for observing/handling intra-spatial atom groups, (3) development of the theoretical technologies for the atomic/molecular processes, and (4) auxiliary activities. The item (2) is intended to obtain the basic knowledge of the principles and devices for handling atom groups in a free space by spatial electromagnetic field handling or the like, and principles of state observation methods, including their possibilities. The item (4) holds the information-exchange meetings. (NEDO)

Fiscal 1997 industrial technology R and D project. Research report on development of use technology of bio- resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This project aims to establish production technology of functional substances, oil degradation and purification technology, and use technology of unused oil fraction through development of cultivation control technology of complex biosystems. For functional material production technology, as functional substances some specific marine bacteria inhibitors, antibreeding substances of microalgae, and UV absorption substances were isolated. The productivity of korormicin as specific inhibitor against marine bacteria was improved considerably by cultivation method. For research on molecular genetic analysis technology, a new identification technology and a simple automatic analysis system of microeucaryotes using genes were developed. For global environment purification technology such as efficient degradation of pollutants, study was made on cultivation control technology of phenol- degrading consortia, population dynamics of oil-degrading microbial consortia and a restoration method of oil pollution by complex biosystem at lower temperature, and the demonstration experiment of oil degradation were carried out. (NEDO)

Achievement report in fiscal 2000 on research and development project for immediately effective and innovative energy environment technologies. Development of new natural gas storage technology using adsorbents; 2000 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kyuchaku zai wo mochiita shinkina ten'nen gasu chozo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In relation with natural gas which contributes to preserving the environment and reducing dependence on petroleum, research and development has been performed on a storage system using adsorbents that allows storage of natural gas at higher density than conventional systems. This paper summarizes the achievements in fiscal 2000. In material development, the current fiscal year has performed the discussions on synthesis of three dimensional complexes. An adsorbent was synthesized successfully that has adsorption performance 2.5 times greater than the secondary complex. In developing an improved activated carbon, an adsorbent was synthesized successfully that has methane adsorption performance four times greater than the compressed gas, by using monolithic activated carbon that uses no binders. Carbon briquettes were manufactured for the basic testing equipment for fuel storage container of natural gas fueled automobiles. In the system development, installation was completed on a bench scale equipment for a gas holder and BOG treatment system, whereas engineering data were acquired from the single-column type high pressure test and two-column type constituent separation and storage test using natural gas. Selection was carried out on applicable vehicle types for the adsorption storage system for natural gas fueled automobiles, and the basic design was made for fabrication of containers of different shapes. (NEDO)

Achievement report in fiscal 2000 on research and development project for immediately effective and innovative energy environment technologies. Development of new natural gas storage technology using adsorbents; 2000 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kyuchaku zai wo mochiita shinkina ten'nen gasu chozo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In relation with natural gas which contributes to preserving the environment and reducing dependence on petroleum, research and development has been performed on a storage system using adsorbents that allows storage of natural gas at higher density than conventional systems. This paper summarizes the achievements in fiscal 2000. In material development, the current fiscal year has performed the discussions on synthesis of three dimensional complexes. An adsorbent was synthesized successfully that has adsorption performance 2.5 times greater than the secondary complex. In developing an improved activated carbon, an adsorbent was synthesized successfully that has methane adsorption performance four times greater than the compressed gas, by using monolithic activated carbon that uses no binders. Carbon briquettes were manufactured for the basic testing equipment for fuel storage container of natural gas fueled automobiles. In the system development, installation was completed on a bench scale equipment for a gas holder and BOG treatment system, whereas engineering data were acquired from the single-column type high pressure test and two-column type constituent separation and storage test using natural gas. Selection was carried out on applicable vehicle types for the adsorption storage system for natural gas fueled automobiles, and the basic design was made for fabrication of containers of different shapes. (NEDO)

Report on fiscal 1998 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (R and D on carbon-based high function material); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Results of R and D for the initial year were compiled concerning the frontier carbon technology R and D project started in fiscal 1998. In the material formation and evaluation studies of SAW (surface acoustic wave) elements, an AlN (aluminum nitride) film and a diamond/Si film were successfully formed by a nitrogen radical assisted pulsed laser vapor deposition method and a reactive DC magnetron sputtering method. Also performed were the simulation analysis of diamond SAW element characteristics and the evaluation studies of the SAW elements. In the development of the film forming and evaluation technologies of ultra thin carbon-based protective film, carbon-based thin films were developed using an ECR (electron-cyclotron resonance) sputtering method. In the development of evaluation technology for the abrasion performance of ultra thin carbon-based protective films, examination and experiment were carried out for the evaluation device and method capable of simulating abrasion performance in an HDD (hard disk drive). In the development of a high performance display device using a carbon nano tube cold cathode electron source, the evaluation of electron emission characteristics was conducted, as was the manufacturing of a RGB surface light source. (NEDO)

FY 1991 report on the results of the contract R and D of the human sense measuring application technology. 3. R and D of a technology to present the mock environment; 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu seika hokokusho. 3. Mogi kankyo teiji gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

As a part of the R and D of a technology to present the mock environment, the following R and D were conducted: (1) method to estimate thermal amenity by life scene of worker; (2) radiation model contributing to improvement of working environment; (3) methods to measure/evaluate/improve the combined environment of working environment/living environment at power plants. In (1), the following were carried out: development of equipment to present thermal environment by life scene and by human body part; measurement of thermal environment; measurement of physiological reaction; measurement of mental reaction; construction of human body thermal model. In (2), the target of the R and D is to develop artificial solar radiation equipment by which the outdoor natural radiation environment can be simulated. The targeted reproduced wave length area of photovoltaic unit model is 400-20,000nm. Therefore, in FY 1991, the selection of photovoltaic unit model parts was experimentally confirmed. The sheet exothermic body of the solar heat reproducing wall heater model was experimentally evaluated to study applicability. In (3), the paper took up 'a study on a method to present/evaluate/improve the composite environment,' and made a basic study on a method to measure/evaluate air transmission sound/solid transmission sound/low-frequency sound. (NEDO)

Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of technologies for producing substitute fuel for petroleum by utilizing organisms; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Technologies of producing useful substances using the substance decomposing/producing functions of complex biosystems and methods of their handling are developed. In the utilization of microbes in the digestive tracts of termites and longicorns, it is made clear that several kinds of termites cleave the {beta}-O-4 ether linkage. In relation to technologies for wood decomposing complex microbial system construction and complex vector system development, a screening system is constructed in which strains that exhibit complex actions are combined. Concerning the advanced utilization of tropical oil plants, conditions are determined for inducing callus out of oil palm tissues. Out of oil palm sarcocarp tissues, mRNA (messenger ribonucleic acid) is isolated for the construction of a cDNA (complementary deoxyribonucleic acid) library. For the purpose of isolating a powerful promoter, a partial base sequence is determined for ubiquitin that frequently expresses itself in cells. A pathogenic bacterium ailing the oil palm is sampled for identification, and it is inferred that the bacterium is a kind of Ganoderma boninense. (NEDO)

FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

FY 1991 report on the results of the contract R and D of the human sense measuring application technology. 2. R and D of the physiological effect measuring technology (2); 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu seika hokokusho. 2. Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu (2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In this paper, the following were studied: (1) easy-wearing net-type brain wave sensor and multi-purpose telemeter; (2) multi-point brain wave measurement. In this fiscal year, the fundamental design and evaluation of these were conducted. In (1), conducted were the study of specifications of system and shape as fundamental design of easy-wearing net-type brain wave sensor, and the evaluation using functional works. As fundamental design of multi-purpose telemeter, studied were the detailed specifications of transmitter and receiver and the system design. In (2), as fundamental design of multi-point brain wave sensor (64 electrodes), conducted were the specifications of system and shape of 19 electrode sensors and the evaluation using functional works trially made. As fundamental design of the analyzer interface, a system was studied for taking brain wave signals of 64 channels into the analyzer by analog/digital conversion. As to the interpolation system of topography, the following were carried out: study of the optimum interpolation system for estimating the electric potential at the portion where the electrode is not installed, based on the electric potential at the portion where 64 brain wave electrodes are installed; and evaluation of the interpolation system using topography by 12-21 electrodes as the pre-stage of 64 electrodes. (NEDO)

FY 1991 report on the results of the contract R and D of the human sense measuring application technology. 3. R and D of a technology to present the mock environment; 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu seika hokokusho. 3. Mogi kankyo teiji gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

As a part of the R and D of a technology to present the mock environment, the following R and D were conducted: (1) method to estimate thermal amenity by life scene of worker; (2) radiation model contributing to improvement of working environment; (3) methods to measure/evaluate/improve the combined environment of working environment/living environment at power plants. In (1), the following were carried out: development of equipment to present thermal environment by life scene and by human body part; measurement of thermal environment; measurement of physiological reaction; measurement of mental reaction; construction of human body thermal model. In (2), the target of the R and D is to develop artificial solar radiation equipment by which the outdoor natural radiation environment can be simulated. The targeted reproduced wave length area of photovoltaic unit model is 400-20,000nm. Therefore, in FY 1991, the selection of photovoltaic unit model parts was experimentally confirmed. The sheet exothermic body of the solar heat reproducing wall heater model was experimentally evaluated to study applicability. In (3), the paper took up 'a study on a method to present/evaluate/improve the composite environment,' and made a basic study on a method to measure/evaluate air transmission sound/solid transmission sound/low-frequency sound. (NEDO)

FY 1998 annual report on the results of new industry creation type industrial science and technology research and development on the research and development of supermetals. Development of techniques for controlling structures of nano-amorphous materials; 1998 nendo super metal no gijutsu kaihatsu. Nano amorphous kozo seigyo zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 results of the development of techniques for controlling structures of nano-amorphous materials. For the development of techniques for finely dispersing fine particles, mechanical alloying (MA) and mechanical milling (MM) are investigated, to structure nano-crystals in common steel, for which hot isostatic pressing is evaluated as a consolidation process for the MA- and MM-prepared powders in the FY 1998. For researches on high-speed particle deposition and super plastic forming, an Al-Ni, Al-Fe and Al-Ti alloy are selected as the nano-structure materials to be prepared by evaporation, and various compositions of these systems are evaporated, in order to investigate their microstructures, mechanical properties and thermal stabilities. For researches on techniques for controlling phases with the aid of high-density energy, the R and D efforts are directed to exploration of composition of high resistance to corrosion by acid at dew point, preparation of non-equilibrium (e.g., amorphous) powders, and development of solidification and forming techniques, with the target of creation of an amorphous alloy showing corrosion resistance at least twice as high as that of the commercial corrosion-resistance material and formable into a bulk shape having a thickness of at least 1 mm. For researches on controlled cooling techniques, the basic data are collected. (NEDO)

Fiscal 1996 global environmental industry technology research related project. Report on the results of the consignment project of research and development of technology for reducing carbon dioxide emissions; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu kanren jigyo. Nisanka tanso nado haishutsu teigen gijutsu kenkyu kaihatsu itaku gyomu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of reducing emissions of carbon dioxide, freon, etc., a research project was carried out of `Research and development of technology for reducing carbon dioxide emissions` which consists of 8 projects. The paper reported the results of the projects. The projects are: (1) Development of waste water treatment of submerged combustion system, (2) Development of thermoelectric generating devices, (3) Development of high performance heat insulation materials, (4) Development of methanol reformer for transportable fuel cell, (5) Development of large pressure reducing valves, (6) Development of large-scale turbo heat pump for district heating and cooling plants, (7) Development of heat pumps for transportation equipment, and (8) Development of thermoelectric cooling devices. In (1), the waste water treatment test was conducted and reached the target. In (2), the thermoelectric device using powder sintering element obtained performance twice the performance level of the existing device. In (3), (4), (5) and (6), the target was all reached. In (7), the results well agreed in a comparison between structural analysis and experiment. The cooling unit by the SPS sintering method using Bi-Te system sintered material element obtained the cooling efficiency almost the same as that by the freon compressor method. 8 refs., 161 figs., 63 tabs.

Development of fiber product recycling technology in fiscal 1998. Achievement report on developing woven product technology utilizing 'waste selvages' generated from weaving process; 1998 nendo sen'i seihin recycle gijutsu kaihatsu seika hokokusho. Seishoku no sai ni hasseisuru 'sutemimi' wo sairiyoshita orimono seihin gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Researches have been made to develop a technology to re-utilize 'waste selvages' generated from weaving process as weaving yarn, and recycle it into toiletry related products such as bath mats and toilet mats. In developing a technology to unify the waste selvage widths, such a research achievement was obtained that one side of the waste selvage width of 19 to 25 mm is most suitable for making the selvages into yarn, whereas the 'waste yarn standard' was established. In the waste selvage winding technology, development was achieved on a dedicated winder which is interlocked with the waste selvage roller on the yarn feeding side. In developing the technologies for waste selvage starching, twisting, and heating, a double twister that can handle very large yarn number counts was developed. For the winding device that can handle yarns of large counts, a re-winder was developed to rewind the yarn by rotating a dying bobbin of the up-twister system. In the weaving technology dealing large count yarns, the tension device and the pile forming device were developed. Twenty-seven kinds of prototype bath mats were fabricated through the experimental production, whose prospect of commercialization has come into the realization range. (NEDO)

FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

Report on the achievements in research and development of a coal liquefaction technology in the Sunshine Project in fiscal 1981 for development of a solvent extraction and liquefaction technology. Development of a brown coal based solvent extraction plant (Research on a primary hydrogenation technology, research on a deliming technology, research on a secondary hydrogenation technology, research on a dehydrogenation technology, and research on liquefaction from catalytic aspect); 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu seika hokokusho. Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (ichiji suiten gijutsu no kenkyu, dakkai gijutsu no kenkyu, niji suiten gijutsu no kenkyu, shokubaimen kara no ekika kenkyu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the achievements in development of brown coal based solvent extraction in the Sunshine Project in fiscal 1981. Element researches were performed to complement and support the development of a liquefaction technology for brown coal produced in Victoria, Australia by using a 50-T/D pilot plant. For the primary hydrogenation technology, a manufacturing experiment was completed by means of nine cycles using a brown coal balancing solvent in a 0.1-t/day bench scale test. Distribution of the formed materials, the solvent properties, and the SRC properties have become nearly constant after 5 to 6 cycles. A test using a batch type device was performed to derive the relationship among dissolution parameters, SRC recovery rates, and deliming rates by using different solvents. For the secondary hydrogenation technology, SRC being the heavy fraction in a primary hydrogenation system (+420 degrees C) was hydrogenated by using an Ni{center_dot}Mo based catalyst at 360 degrees C and 250 kg/cm{sup 2}. A prospect was attained that the processing is possible by using a fixed bed reactor. A test using a small continuous dehydration testing device was carried out by using creosote oil as the solvent and by varying the evaporator operating conditions. Dehydration rate of 90 to 95% was obtained. Discussions were given on selecting catalysts for the secondary hydrogenation of the fixed bed method, and on factors of activity deterioration. A secondary hydrogenation test reactor of the suspended bed method was completed. (NEDO)

Fiscal 2000 research achievement report. Super-advanced electronics technologies development promotion project; 2000 nendo kenkyu seika hokokusho. Cho sentan gijutsu kaihatsu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-01

For the construction of a common base of key technologies in the domain of electronics and information with the influence propagating across a wide range of industries, research and development was conducted of technologies of ultrafine working process, technologies of ultimate measurement, analysis, and control, technologies of new functional electronic materials, etc. Studied in the field of electron beam lithography were high precision and large area imaging technology, highly accurate electron optics control system technology, and beam monitoring technology. Studied in the field of ultrashort wavelength electromagnetic wave patterning system technology were proximity ultrashort wavelength electromagnetic wave patterning system technology, reduced ultrashort wavelength electromagnetic wave patterning system technology, and ultrahigh precision new materials patterning technology. Also studied were technologies of super-advanced plasma measurement, analysis, and control, and technology of super-advanced cleaning. In the field of technologies of new functional elements and films, studies were conducted about technologies of highly sensitive GMR (giant magnetoresistive) film and head fabrication process for contact magnetic recording and technologies of a spin-valve head with submicron track width for contact magnetic recording. (NEDO)

Evaluation report on the R and D of the membrane separation process introduction technology; Makubunri process donyu gijutsu no kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper reported the R and D of the membrane separation process introduction technology during a period of 1994 through 1998. The membrane separation technology is not associated with the phase change which requires large energy and expected to be an energy saving process. For the production of membranes required of high functions, the vapor deposition polymerization method was considered, and high order structure control of the membrane, control of adhesion and attachment, and control of orientation, and development of the high polymerization technology were required. For the high grade control of vapor polymerization, the substrate surface structure/quality were important. The molecular level analysis of the vapor deposition surface was also needed. Therefore, the paper took notice of STM (scanning tunneling microscopy), AFM (atomic force microscopy) and HREELS (high resolution electron energy loss spectroscopy) as surface atomic/molecular configuration analysis technology, and designed/fabricated and studied the high resolving power and high sensitivity analysis equipment using the analysis equipment which combined HREELS and STM and the analysis equipment using SFG (sum frequency generation) which can detect signals in the low frequency region. Making full use of the highest technology, technology was able to be developed for substrate surface analysis and surface reaction analysis technologies which become the basis of the high performance separation membrane fabrication technology by the vapor deposition polymerization method indispensable for introduction of the membrane separation process. The technology can be the base applicable to a lot of fields where surfaces and interfaces are concerned

Development of high productive technology for vegetables. Performance of a test plant and experiments of spinach cultivation. Kounouritsu yasai seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sekiyama, Tetsuo; Okano, Toshiaki; Hoshi, Takehiko; Kosakai, Kazuyoshi; Okabe, Katsumi; Hanyu, Hiromichi

1987-02-01

Technology of a system using both sunlight and artificial light was developed, and a vegetable plant with the system was developed to study the use of low-cost off-peak electricity for the improvement of vegetable productivity and quality. A test plant of 340m/sup 2/ was constructed. The greenhouse was designed in a pellette house style where light is controlled through grains of styrofoam by blowing. To use low-cost offpeak electricity, heat reservoir facility for cold (ice) and hot water was provided. An environment measuring system was provided for the analysis of the relationship between the environmental conditions, growth of vegetables and consumption of electricity. Four cultivation experiments were carried out, and the yield of spinach increased by 6 to 7 times (10 kg/m/sup 2/) in summer season, and the period of growth in winter time was shortened to 1/2 to 1/3 (25 days). Results of the study on the performance of the facilities such as cultivation room, light environment, CO/sub 2/ environment, hydroponic device, etc. are also reported. (32 figs, 5 tabs)

Development of high field magnets at the National Research Institute for Metals. Kinzoku zairyo gijutsu kenkyusho ni okeru kojikai magnet gun no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kiyoshi, T.; Inoue, K.; Maeda, H. (National Research Inst. for Metals, Tsukuba (Japan))

1993-06-20

Sinece 1988, the Scince and Technology Agency has initiated the superconductor multicore project, which has a purpose of the versatile study on the high temperature superconducting materials of the oxide series. The National Research Institute for Metals is in charge of 5 cores out of them, and in the performance evaluation core which is one of them, the development of each kind of the high field magnets is being advanced for evaluating the characteristics under the high magnetic field. As the magnets, including the 40T class hybrid magnet which generates the steady state magnetic field of 40T, the superconducting magnet of 20T with a large diameter which generates the magnetic field over 20T with a superconductor, the condenser bank system for the pulse magnet to generate the pulse magnetic field up to 80T, and the ultra-precise magnet system which generates the magnetic field with a high uniformity will be consolidated. Keeping pace with a removal of the National Research Institute for Metals to Tsukuba, the construction of the strong magnetic field station is being advanced in the Sakura area. These several kinds of magnets are scheduled to be used in turn for the international joint study. 33 refs., 5 figs., 4 tabs.

Report on fiscal 1998 results. Item of development, 'research on technologies for disaster prediction'; Saigai yochi gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Development was conducted, with the results summarized, for an electromagnetic probing system using a superconducting quantum interference device (SQUID) sensor, for the purpose of establishing disaster prediction technologies by grasping the underground structure highly precisely and three-dimensionally. The developed electromagnetic probing system consists of SQUID elements, 3-axial probe with driving circuits, liquid nitrogen Dewars, automatic control circuit of SQUID biases, high speed multi-channel A/D converter, mobile computer and a battery unit. The software has the function of SQUID bias control, measurement, data saving and data analysis. For the electromagnetic probing analytical program, an one- and three-dimensional interpretation programs were developed. As a result of the field tests, the subject system proved to be strong against city noise and advantageous for fault investigation in urban areas. In addition, being a sensor of multi-component/differential measurement, the system is also supposed to be useful in mine surveying. (NEDO)

FY 1999 research and development results. Technological development of superconducting power storage systems; Chodendo denryoku chozo system gijutsu kaihatsu 1999 nendo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for technological surveys on the superconducting power storage system (SMES) for cost reduction and high-temperature SMES, and the FY 1999 results are reported. The SMES cost analysis/evaluation program establishes the (basic flow for cost analysis/evaluation) for cost evaluation. The program for the SMES systems for system stabilization sets the specifications of 100MW as output and 15kWh as storage capacity at the generator end and intermediate switching station. The program for SMES systems for load fluctuation compensation and frequency control sets the specifications of 100MW as output and 500kWh as storage capacity at the installation site as the load end, and the investigation of high-temperature SMES technology is conducted on the conceptual designs of the SMES for system stabilization application (100MW, 15kWh) of toroidal coil type. The optimization designs are made for these systems. The investigation of the technology for high-temperature superconducting wires involves fabrication on a trial basis and evaluation for the characteristic evaluation coils, and characteristic measurement and applicability investigation for the large-current short conductor. (NEDO)

Data book on new energy technology in FY 1997. Wind power generation; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Furyoku hatsuden

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is an urgent necessity for Japan to promote the technological development and accelerate the introduction and diffusion of new energy. In order to diffuse and enlighten the introduction of new energy technology efficiently, it is necessary to compile various information regarding new energy in a comprehensive and systematic way, and formulate a database. Aiming at the systematic formulation of data on new energy, this survey focuses on the field of wind power generation system (WPS) and provides a collection of the latest published data on WPS, particularly regarding the worldwide installed wind power capacity, support plan and government policies, current situations of WPS market, and major technical characteristics of typical wind turbines. This report consists of the significance of wind energy, world market of wind turbines, government policies, international wind energy development, subsidies for wind energy, procedures of wind turbine system installation, governmental measures for wind energy development, subsidiary companies and organizations, basis of wind energy, and Japan`s wind energy development in 1997

Data book on new energy technology development in FY 1997. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this survey is to grasp the trends of technology development of fuel cells and their market, and to provide data required for supporting the introduction and diffusion of fuel cells. This report consists of Part 1 titled as `Trends of development of fuel cells in FY 1997`, and Part 2 titled as `Compiled data`. The Part 1 consists of three chapters, i.e., Chapter 1 titled as `Introduction`, Chapter 2 as `Development trends of fuel cells for on-site power generation`, and Chapter 3 as `Trends of development of fuel cells for mobile objects and fuel cell-powered vehicles`. The introductory chapter not only outlines the development trends but also describes the results of the 5th Grove Fuel Cell Symposium noticed as the major global international symposium on fuel cell in general and the environmental problems discussed at the COP3 Kyoto Conference, both held in TY 1997. The Part 2 contains the principles, system configurations and applications of fuel cells, PAFC, MCFC, SOFC, PEFC, modifier, DMFC, development trend of fuel cell-powered vehicles, and national policies for fuel cells in Japan. The Appendix features a report of the new technique investigation working group and information on fuel cells from newspapers. 100 refs., 4 figs.

FY1999 annual report on the research and development on practical industrial cogeneration technology; 1999 nendo sangyoyo cogeneration jitsuyo gijutsu kaihatsu kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The basic plan aims to quicken the practical application of the industrial HBGT (hybrid gas turbine) cogeneration technology and thereby to realize high-efficiency energy utilization for reduction in CO2 emission. For this purpose, a medium-scale HBGT, expected to be high in efficiency and low in polluting, and its components are subjected to assessment tests and endurance tests to prove that there are reliability and soundness in HBGT. Ceramic members are developed which are high in strength at elevated temperatures and in resistance to oxidation, and are subjected to assessment so that they will be further improved in reliability and durability. An HBGT is designed, fabricated, and operated. The engine system is tested for performance, and the performance is improved. It is put to a long-term operation, which is to confirm the presence of soundness and reliability in HBGT as an industrial cogeneration system. Industrial fields in which HBGT will be useful are selected and surveys are conducted to find out how it will function in such selected fields. Problems which HBGT will encounter upon practical application are extracted, and measures for solving them are clarified. Such an HBGT will have a shaft output of approximately 8,000kW, engine thermal efficiency of not less than 34%, and a turbine inlet temperature of approximately 1,250 degrees C. (NEDO)

Development of acoustic partial discharge detection device; Bubun hoden kenshutsusochi wo riyo shita onkyo niyoru hendensetsubi no zetsuen rekka shindan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Suenaga, Kiyoka [Kawasaki Steel Corp., Tokyo (Japan)

1999-06-15

This paper introduces an acoustic partial discharge detection device, consisting of a microphone, amplifier circuit for analog signals, A/D (Digital Signal Processor). This device has the following unique characteristics: (1) Judging whether or not there is partial discharge by analyzing supersonic signals. (2) High sensitivity for detecting discharge ; 100 pC from a distance of 1.2 m. (3)Locating the position of discharge occurrence by using a sharpe directional parabola microphone and laser beam pointer. The detector was used in the steel works to detect partial discharge on high-voltage electrical apparatus, where faults due to partial discharge were found in the potential transformer and current transformer. The effectiveness of the device was thus verified. (author)

Achievement report for fiscal 1998 on development of advanced household electric appliance recycling technology; 1998 nendo senshinteki kaden recycle gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to develop a household electric appliance recycling technology, research and development has been made on crushing of compressors, separation of resins and metals, and regenerative utilization of urethane used as the refrigerator heat insulating material. In the compressor crushing technology, development was made on a ring hammer crusher of wood pattern horizontal type. In the research of the resin-metal separation technology, the dry-type separation and material purity were enhanced successfully by means of classification of materials to be crushed according to grain sizes, and classification using an eddy current screening device and a specific gravity screening device. In the research of the urethane regenerative utilization technology, the contained fluorocarbon was decomposed at the rate of 99.999% by modifying and rinsing the pyrolytic gas from the urethane by means of cracking, having achieved to make the material innocuous. The fuel gas thus obtained can be utilized for electric power generation. In addition, a method to granulate the material was established by mixing it with thermo-plastic resins. It was discovered that using the recovered urethane, which is pulverized smaller than 300 {mu} m, can elevate the heat insulation performance when it is used as the vacuum heat insulator, proving its capability of being re-utilized in refrigerators. (NEDO)

Fiscal 1998 R and D report on environment-friendly hydrogen production technology; Kankyo chowagata suiso seizo gijutsu kenkyu kaihatsu 1998 nendo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For efficient oil-free environment-friendly production of hydrogen necessary for oil refining process and effective use of CO{sub 2}, this project develops the efficient hydrogen production techniques by using a capacity of microorganisms. On the R and D on improvement of screening and breeding for photosynthetic microorganisms, introduction of different hydrogenases, acquisition of hydrogen uptake negative strains, control of photosynthetic pigment expression, breeding of PHB synthesis negative strains were carried out continuously, and some problems were arranged confirming the contribution to increasing a hydrogen production capacity. On the R and D on large-scale cultivation techniques, engineering data were collected by using a module continuously. Based on the engineering data collected by the module test, the feasibility study was made on a possibility as industrial technology from the viewpoint of a profitability and environmental harmony. Screening of bacterial strains suitable for 4 kinds of wastewater and capable of producing hydrogen under extreme conditions, and basic studies on photoreactor and cultivation technique were conducted by outside research organizations. (NEDO)

Summary of the research achievements in fiscal 1990 in developing coal liquefying technologies; Sekitan ekika gijutsu kaihatsu 1990 nendo kenkyu seika no gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

This paper describes the summary of the research achievements in fiscal 1990 in developing coal liquefying technologies. The bituminous coal liquefaction project is scheduled to have a 150-t/d pilot plant start operation from the latter half of fiscal 1994. Research problems were reviewed based on the basic and detailed designs. Construction processes were also reviewed by each facility. Detailed design was performed on the main four facilities for pretreatment, liquefying reaction, liquefied oil distillation, and solvent hydrogenation. Support researches were carried out on the pilot plant in addition to 1-t/d PSU and small testing devices. In the research of a brown coal liquefying technology, operation of the pilot plant (50 t/d) was resumed after completion of the long-term operation (Run 7) having been executed in fiscal 1989, and after the extraordinary repair. The planned operation has been completed as scheduled. Modification and repair works were also carried out. Researches were made on upgrading of brown coal liquefied oil, and a petroleum mixing technology. The paper also describes the support researches. In developing the common basic technologies, studies were performed on development of plant devices, investigation on coal type selection, applications of coal liquefied products, and a refining technology. An environment preserving technology was also developed. The development made it possible to identify the whole image relative to the relevant laws and regulations on the comprehensive operation oil in the whole fraction and by fractions. Comprehensive management of the research and development was also implemented. (NEDO)

Fiscal 1980 Sunshine Project research report. Removal technology of H{sub 2}S; 1980 nendo ryuka suiso jokyo gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the fiscal 1980 research result on removal process and equipment of H{sub 2}S from condensate and waste gas of turbine inlet steam and turbine outlet condensers of geothermal power plants. In the research on continuous measurement method of H{sub 2}S in geothermal steam, the continuous measurement equipment was completed by improving the heat conduction type steam qualitative dilution equipment developed in last year. The test result of this equipment in Onikobe geothermal power plant gave interesting data showing cyclic fluctuation of H{sub 2}S concentration. In the research on treatment of turbine inlet steam, both physical and chemical treatments were unpractical because of their very expensive costs. In the research on treatment of turbine outlet fluid by selecting RET method for waste gas and diffusion method for condensate, the field test result by using real fluid in geothermal power plants made it possible to select the optimum process according to conditions of turbine outlet fluid, and to estimate removal costs of H{sub 2}S precisely. (NEDO)

Summary of the research achievements in fiscal 1988. Development of coal liquefaction technologies; Sekitan ekika gijutsu kaihatsu. 1988 nendo kenkyu seika no gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

This paper reports the summary of the research and development works in fiscal 1988. The following researches were carried out: as development of a bituminous coal liquefaction technology, studies by using a pilot plant, studies on support of the pilot plant (studies by using an experimental plant (studies by using a 1-t/d PSU, development of an optimal pretreatment technology for coals to be used for liquefaction, studies on improvement in fraction oil distribution in the NEDOL process, and studies by using a 1-t/d plant)), and (studies by using a small device (studies on coal liquefying conditions, and studies on solvent hydrogenation catalysts)). Studies were carried out on operation of the pilot plant, and on support of the pilot plant operation. Materials for auxiliary machinery were developed (including in-plant test of new materials), and so were the devices (including development of a let-down valve) as trial fabrication and development of the plant devices and materials. As coal type selection and survey, coal types were surveyed, and liquefaction performance of Chinese coals was tested. In order to develop applications of coal liquefied products and a refining technology, developments were carried out on up-grading of the coal liquefied oil, a petroleum mixing technology, and a technology to separate hetero compounds in coal liquefied oil, and applications of the compounds. (NEDO)

Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

FY 1998 Report on development of technologies for commercialization of industrial solar systems. Summary of the abstracts (Research and development management); 1998 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika gaiyo sogoban. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The FY 1998 programs for development of technologies for commercialization of industrial solar systems include those for freezing/refrigeration systems utilizing solar heat, and international joint programs for development of technologies for the solar heat-utilizing systems. The studies are also conducted to draw the technological development programs for the solar heat-utilizing systems to be developed in the future. For development of the solar heat-utilizing freezing/refrigeration systems, the efforts are directed to extending service life of hydrogen occluding alloy to at least 10 years, which is one of the final targets. High reversibility up to 1,000 cycles is confirmed with the alloy working at low temperature for generating low-temperature heat. The international joint programs for technological development include technology evaluation of lumber drying by solar heat by operating the pilot plant, training of engineers and study on commercialization of the concept in Republic of Indonesia. The studies on technological development of solar heat-utilizing systems include those on classification of the solar heat-utilizing systems by area and utilization type, and evaluation of operating temperature levels and the merits and themes/problems. (NEDO)

Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly crystalline polymeric material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo saishu kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-01

Basic technologies are developed involving highly crystalline polymeric materials comparable to metals in dynamic property even when used singly. The aim is to expand the application scope of polymeric materials including those designed as structural materials so that their light weight, high resistance to corrosion, and excellent machinability may be utilized in various fields. Target performance includes an elastic modulus under bending force of 100GPa or more in anisotropic materials and 50GPa or more in isotropic materials, a linear expansion coefficient of 5 times 10{sup -5}/degrees C or less, and a thermal deformation temperature of 180 degrees C or more. Tasks faced in relation to film or molded articles of anisotropic materials are the rigid molecular design, molding method including molecular orientation control, and molecular complex technology; and, in isotropic materials, the strengthening of interaction between molecules, establishment of molding methods, and equipping materials with high machinability. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. To be mentioned are achievements involving the generation of multidimensionally bound diacetylene polymeric crystals, higher elastic modulus and moldability provided to polyarylate materials, magnetic field orientation, ultrahigh-elasticity layered body, and organic-inorganic ionically bonded complex material, etc. (NEDO)

Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the mechanism of light deterioration reaction of photochromic molecules, it was disclosed that 6-nitrospirobenzopyran has the light deterioration caused from the excitation triplet state. This disclosure presents a possibility of preventing the light deterioration. New derivatives that show photochromism were synthesized, and thin films were produced by using the LB process. This indicates a possibility of producing the photochromic materials as the high multiplex recording material. With regard to PHB materials, an evaluation technology having spectrum resolution of the world's highest level was established and measurements were performed. Hole formation was verified for the first time in the world at the temperature higher than the liquid nitrogen temperature by using a PHB material of ionic porphin/polyvinyl alcohol systems. This verification indicates a feasibility of practically usable PHB materials. (NEDO)

Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

Fiscal 1996 report on the results of the study under a consignment from NEDO of environmental friendly type metal base-materials recycling utilization basic technology and element/overall process. For public; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko kyodo kenkyu itaku. Kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu: yoso sogo process kenkyu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A study of `the next generation new iron steel making process` was conducted in which impurity elements in scrap are removed and recycled into high quality steel making materials, and at the same time total emissions are reduced during the process from scrap melting to steel making. The paper reported the fiscal 1996 results. In the study of the scrap recycling process, conducted were a study of the total system to remove impurities in the high temperature preheating furnace, a large scale experiment of de-coaling combined type de-coppering/de-tinning under reduced pressure of iron melting, a study of recycling technology of dust to the scrap melting furnace, etc. In the study on preheating/melting technology, a study of the scrap melting furnace of high-productivity/low-energy vertical type, a study of the scrap preheating method using the packed bed type preheating furnace, a study on the flue gas control at the time of preheating/melting, a study of the fast assessment method for organic compounds in flue gas, etc. In the evaluation of the total system, a study of preheating/melting/environmental systems using experimental plants. 20 refs., 23 figs., 10 tabs.

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the synthesis and processing of advanced biomaterials (fixation and effective utilization of carbon dioxide using peptides); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (peptide oyo nisanka tanso koteika yuko riyo gijutsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In fiscal 1997, study was made on formation of peptides with a biogenic function and molecular recognition function, and peptide materials. The existing automatic design technique of peptides including non-natural amino acids was applied to design of complementary peptides of proteins with known structures to optimize a development technique of ligand. Practical function of peptides as advanced receptor ligand was verified by applying the existing conformation control technique to stable holding of peptide active conformation. Creation of bio-materials, and development of preparation technology of bio-substrates and materializing technology of functional molecular materials were carried out. To construct an electron transfer system by self- organized body of peptides formed on a substrate, a peptide molecular device was prepared and verified using linkers. To use peptides as photoelectron functional molecule, metallized peptide with main helix structure was prepared. The possibility of molecular materials with a fixation function of CO2 was examined. A high-sensitivity bio-sensor was also mentioned. 75 refs., 130 figs., 25 tabs.

Achievement report of projects in fiscal 2000 for measures on technologies to fix and utilize effectively carbon dioxide. Development of program system technologies to fix and utilize effectively carbon dioxide - researches on key technologies (Developing technology to fix carbon dioxide electrochemically); 2000 nendo program hoshiki nisanka tanso koteika yuko riyo gijutsu kaihatsu (kiban gijutsu kenkyu) seika hokokusho (kokaiyo). Nisanka tanso no denki kagakuteki koteika gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to prevent global warming, research and development has been made on a carbon dioxide fixation technology using electrochemical means. This paper summarizes the achievements in fiscal 2000. In the research of a technology to return carbon dioxide to hydrocarbon such as methane electrochemically utilizing the high concentration carbon dioxide-methanol system, basic studies were performed on electrolytic reduction of CO2 using a methanol solvent system, and experimental studies were executed on high-speed reduction of carbon dioxide using gas diffusion electrodes. In the basic property experiment on diamond electrodes, high carbon dioxide reduction activity was obtained by having copper carried in the diamond electrode. In the CO2 electrolytic reduction experiment on three-phase interface using a copper net electrode, CO, ethylene, and methane were produced, while the electrode has retained the activity for an extended period of time, and the CO2 conversion rate reached about 66%. In structuring an electrochemical carbon dioxide fixation system, specifications for the CO2 electrolytic reduction equipment were determined, design, manufacturing, and electrode materials were selected, supporting electrolytes were discussed, and the entire system flow and liquid resistance were discussed. (NEDO)

FY 1993 research and development of the technology for controlling structures of functional composite members. R and D of advanced surface processing for methane-fueled aircraft engine members (Technology for controlling the microscopic structures of superhigh-temperature members); 1993 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). Chokoon buzai micro kozo seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Described herein are the results of the FY1993 research and development project, implemented for development of the technologies for modification of material surfaces and interfaces, with the objectives to develop the optimum members for methane-fueled aircraft engines. For R and D of multi-layered films with controlled microscopic structures, the tests are conducted for forming thin-film layers by, e.g., ion implantation, ion mixing and implantation of large quantities of ions as the surface controlling/modification techniques based on, e.g., ionic techniques. The tests are conducted for, e.g., chemical vapor-phase reaction evaporation and low-pressure plasma spraying as the technologies for forming multi-functional films of, e.g., high reliability and resistance to corrosion. For development of the technologies for controlling/compositing the microscopic structures, the tests are conducted for, e.g., selection of the matrix materials, and prevention/removal of defects by the chemical vapor-phase reaction penetration treatment effected for extended periods. For development of the technologies for evaluation of the characteristics under superhigh-temperature environments, the tests are conducted to investigate the mechanical characteristics of isotropically uniform metallic materials under multi-dimensional stresses and evaluation thereof, and mechanical and thermal characteristics of carbon-fiber-reinforced carbon composites and evaluation thereof. (NEDO)

Fiscal 1998 research achievement report. Project for developing key technologies for electronic devices (Projection X-ray exposure process technology and active reflective device structure technology); 1998 nendo denshi device kiban gijutsu kaihatsu jigyo seika hokokusho. Shukusho X sen roko process gijutsu to active hansha kozogata keisei gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Studies were conducted for the development of technologies of the very advanced level relating to an ultrafine machining process and high-performance reflector type liquid crystal display structure formation. Studied in the research and development of projection X-ray exposure process technology were multi-layer film formation, absorbing body film formation, absorbing body machining, multi-layer film mask defect evaluation, and cleaning for defect reduction. As the result, multi-layer film formation by Helicon sputtering and formation and machining of film with Ta acting as absorbing body therein were carried out, and it was found by actual exposure experiments that there were excellent X-ray reflectivity and absorbing body contrast. Furthermore, a study was made of cleaning using dummy foreign matters, and 100% removal of dummy foreign matters was achieved across a range up to the 70nm level. Studied in the development of active reflective device structure technology were the addition of an electrical control function to the reflector, addition of an unreflected rays absorbing function, production of a bias stabilized device for the practical application of a memory function, and the development of materials for the fabrication of the said devices. (NEDO)

New Sunshine Project FY 1996 report on the results of development of photovoltaic power generation system commercialization technologies. Research on commercialization of the technologies for production of thin-film photovoltaic cells (Development of fabrication technologies of high-quality CuInSe{sub 2}-based thin-film solar cells); 1996 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu (kohinshitsuka gijutsu (CuInSe{sub 2} taiyo denchi seizo no gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Described herein are the FY 1996 results of development of fabrication technologies for high-quality CuInSe{sub 2}-based photovoltaic cells. The Cu-Ga alloy/In-stacked precursor film is prepared for production of the high-quality thin-film absorber applicable to large-area module fabrication, and selenized by the vapor-phase selenization in a H{sub 2}Se gas atmosphere to produce the thin light-absorbing film in which In and Ga are present at graded concentrations. Increasing Ga alloy content in the CIGS-based thin-film photovoltaic cell fails to widen the forbidden band and improve V{sub oc}, and further optimization works are needed. The method is developed for production of thin-film buffer layer of sulfur-containing Zn compound which can give the cell characteristics equivalent to those of CdS generally used for CIS-based thin-film photovoltaic cell. It is clarified that the photovoltaic cell characteristics can be improved by use of a transparent electroconductive ZnO film of stacked structure, produced by a combination of RF sputtering and DC sputtering. For the patterning technologies necessary for forming series connection on a mini-module, the laser scribing method is applicable to the metal base-electrode, and the mechanical scribing method to the light absorber and window layer. (NEDO)

Achievement report for fiscal 1998 on business auxiliary to New Sunshine Program. Hot water-aided power generation plant development (Development of deep-seated geothermal resources exploitation technology and development of deep-seated geothermal resources excavating technology); 1998 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the general exploitation scheme, technological information is collected about cement overseas, DHM (down hole motor), etc. In the development of heat-resistant durable bits, an improved version of the 350 degrees C real bit manufactured in fiscal 1997 undergoes a test in a real bore, and is evaluated for its general performance. In the development of high-temperature cement slurries, the ultralow specific gravity cement slurry for casing cement developed in fiscal 1997 is subjected to evaluation. It is examined by chemical analysis and powder X-ray diffraction, and its fluidity, free water, rate of dehydration, and compression strength at 250 degrees C are measured. In a real bore test, a slurry of the optimum composition is prepared and then hardened, and the hardened body is kept exposed to geothermal environments for eight weeks. It is then found that the hardened body retains a compression strength of 70kgf/cm{sup 2}. In the development of a down hole motor, a scale model, real in diameter and shortened in length, is built of the motor section, and is tested in circulating water and oil at normal and high temperatures, and its behavior and performance are evaluated. (NEDO)

Achievement report for fiscal 1998 on research and development of technologies for creating high-performance materials under the industrial and scientific technology research and development project. Control of condensation-based precision structures (High-performance materials for power plant facilities); 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) shukugokei seimitsu kozo seigyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The goal is to prepare a base for the development of polymerizing catalysts and precision polymerization processes which will enable the arbitrary control of molecular weight, regularity, branching, and primary structures such as terminal groups, which effort will lead to a remarkable advancement in condensation polymerization and open-ring polymeric material performance. Endeavors are on to fulfill two separate purposes, that is, precision condensation polymerization and controlled open-ring polymerization. In the study of precision condensation polymerization, at issue are basic studies and the development of precision control technologies for arrangement, molecular weight, branching, and matrix condensation polymerization. Also at issue are the development of technologies of position selective oxidization polymerization and precision conjugate high-molecular condensation synthesis. Concerning open-ring control polymerization, precision control technologies will be developed involving branching, molecular weight, crosslinking, arrangement, and the structure of cyclocarbonate open-ring polymerization. Open-ring control polymerization technologies are also under study by use of organic metal complexes. A survey of technological trends is also explained. (NEDO)

1998 report on results of R and D project for industrial science and technology (R and D for technologies of producing innovative high performance material) (development of technologies for structural control material). R and D for high stimuli-responsive material; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A report was made on the results of 1998 R and D concerning high stimuli-responsive materials. This R and D was intended to develop technologies for producing, by copying organism, innovative new stocks and new materials which repeatedly provide functions such as separating, transmitting and moving in response to stimuli. In the R and D of polymeric high stimuli-responsive materials, studies were conducted on multi-stimuli-responsive separation materials, molecular recognition controlled separation materials, and cell adhesion/separation materials with molecular recognition function. In the R and D of composite high stimuli-responsive materials, release controlled function materials and materials for actuator were studied. The investigation and research of common basic technologies were carried out on such subjects as synthesis and functional development of multi-signal responded polymer gels, development of temperature-responsive chromatography, synthesis and characterization of novel stimuli-sensitive materials, studies on structural characterization of intelligent gels, novel thermosensitive polymers, polyelectrolytic model networks, etc. (NEDO)

Fiscal 1999 R and D project for industrial science and technology. R and D of technology for creating innovative and high-functional material - development of technology for structural control material (Report on result of R and D of harmonized molecular material); 1999 nendo dokusoteki kokino zairyo sosei gijutsu no keknkyu kaihatsu seika hokokusho. Kozo seigyo zairyo gijutsu kaihatsu (bunshi kyocho zairyo no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of contributing to the development of optical elements, devices, sensors, high performance catalysts, etc., R and D was conducted on fundamental technologies for creating materials using harmonized molecular actions, and the fiscal 1999 results were reported. In the R and D of self-assembled molecular film materials, an electric-field sensitive self-assembled molecular film was experimentally manufactured, as were self-assembling electroluminescent and lyotropic liquid crystal pigmentary film materials. In the R and D of mesophase materials, for rod-like liquid crystal systems, a material was successfully developed possessing a transparency of 90% in the visible region accompanied with an optical phase difference of 4.0 microns. For disk-like liquid crystal systems, a diminishing tendency of obtainable photoelectric current was confirmed even with a small change in the orientation after photopolymerization. In the R and D of microporous materials, synthesis was performed for system-controlled metallosilicates and shape-controlled microporous materials. Further, structural correlation was examined for organic templates and microporous materials. (NEDO)

[Development of analysis software package for the two kinds of Japanese fluoro-d-glucose-positron emission tomography guideline].

Science.gov (United States)

Matsumoto, Keiichi; Endo, Keigo

2013-06-01

Two kinds of Japanese guidelines for the data acquisition protocol of oncology fluoro-D-glucose-positron emission tomography (FDG-PET)/computed tomography (CT) scans were created by the joint task force of the Japanese Society of Nuclear Medicine Technology (JSNMT) and the Japanese Society of Nuclear Medicine (JSNM), and published in Kakuigaku-Gijutsu 27(5): 425-456, 2007 and 29(2): 195-235, 2009. These guidelines aim to standardize PET image quality among facilities and different PET/CT scanner models. The objective of this study was to develop a personal computer-based performance measurement and image quality processor for the two kinds of Japanese guidelines for oncology (18)F-FDG PET/CT scans. We call this software package the "PET quality control tool" (PETquact). Microsoft Corporation's Windows(™) is used as the operating system for PETquact, which requires 1070×720 image resolution and includes 12 different applications. The accuracy was examined for numerous applications of PETquact. For example, in the sensitivity application, the system sensitivity measurement results were equivalent when comparing two PET sinograms obtained from the PETquact and the report. PETquact is suited for analysis of the two kinds of Japanese guideline, and it shows excellent spec to performance measurements and image quality analysis. PETquact can be used at any facility if the software package is installed on a laptop computer.

Report on achievement for fiscal 1998. Global environment industry technology development promotion project (the advanced technology survey and research project); 1998 nendo seika hokoiusho. Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo (sentan gijutsu chosa kenkyu jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to structure innovative technologies to solve effectively the global environment problems, it is important to incorporate infra-structural technologies that have been achieved by universities and other research institutions. The fiscal 1998 project has commissioned 25 researches found superior from among research plans that have been invited during fiscal 1997. This paper enumerates the main themes including those under continued research. The research themes include: fixation of phosphor by using photo-energy, utilization of nitrogen fixing bacteria in rice plant roots for the purpose of carbon dioxide reduction, new functional solid ultra-strong acids for clean chemical processes, fixation of warming gases by using ultra critical fluid catalytic reactions, photo-catalysts having microporous structure, whose energy structure is controlled, waste water purification by using stimulation sensitive polymers, a practical and small high-speed environment purification system by means of a simple technology to cultivate high concentration bacteria of microorganisms, fundamental analysis of response to specific wavelength light in photosynthesized microorganisms, bio-remediation utilizing symbiotic systems of plants and bacteria, high efficiency catalysts purposed for total decomposition of water, and separation of carbon dioxide in deep sea bottoms by controlling hydrate crystal growth. (NEDO)

Report on results concerning development of supermetal technology (FY2000). Innovative manufacturing technology for iron-based mesoscopic structured material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Tetsu kei mesoscopic soshiki seigyo zairyo sosei gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of establishing innovative manufacturing technology for microstructure steel having a crystal grain size of about 1 {mu}m or less and a dimensional thickness of 1 mm or more by homogeneous multi-phase structure steel making, R and D was conducted, with fiscal 2000 results compiled. This year, R and D, using a multi-functional integrated test rolling mill, resulted in obtaining ultra-fine grained steel, a steel plate of 5 mm in thickness and 100 mm in width with grains of 1 {mu}m or less homogeneously in the thickness direction. In the investigation on the characterization by the steel plate sample thus obtained and on the method for preventing degradation in elongation, it was proved that an ultra-refined microstructure containing martensite or austenite as the secondary phase has a suppressing effect on the degradation in elongation. Further, examination was made on the widening of a process window for the practicability in the future and on the optimization of large strain deformation conditions. In the method of analyzing and evaluating ultra-refined microstructures, an analysis technology such as an in-lens SEM was proved to be extremely effective on the analysis of microstructures of supermetals created by large strain deformation as well as on the observation of microstructures of a submicron level. (NEDO)

Hydrogen energy technology development conference. From production of hydrogen to application of utilization technologies and metal hydrides, and examples; Suiso energy gijutsu kaihatsu kaigi. Suiso no seizo kara riyo gijutsu kinzoku suisokabutsu no oyo to jirei

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-02-14

The hydrogen energy technology development conference was held on February 14 to 17, 1984 in Tokyo. For hydrogen energy systems and production of hydrogen from water, 6 papers were presented for, e.g., the future of hydrogen energy, current state and future of hydrogen production processes, and current state of thermochemical hydrogen technology development. For hydrogen production, 6 papers were presented for, e.g., production of hydrogen from steel mill gas, coal and methanol. For metal hydrides and their applications, 6 papers were presented for, e.g., current state of development of hydrogen-occluding alloy materials, analysis of heat transfer in metal hydride layers modified with an organic compound and its simulation, and development of a large-size hydrogen storage system for industrial purposes. For hydrogen utilization technologies, 8 papers were presented for, e.g., combustion technologies, engines incorporating metal hydrides, safety of metal hydrides, hydrogen embrittlement of system materials, development trends of phosphate type fuel cells, and alkali and other low-temperature type fuel cells. (NEDO)

Report on the achievements in the projects subsidized by the Sunshine Project in fiscal 1981. Data 3. Development of a coal liquefaction technology - development of a solvent extraction and liquefaction technology - 'development of a brown coal based solvent extraction plant' (Development of a 50-t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 3). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Developmental researches were carried out on a liquefaction plant for the Victoria brown coal produced in Australia (a 50-t/d pilot plant). In fiscal 1981, detailed design was performed on the primary hydrogenation system by using the process conception and the design data obtained in the element studies. Part of the devices was procured, and the site construction was begun. The present data is a collection of drawings in relation with the instrumentation design, such as the meter specifications, front view drawings for meter panels, drawings for panel arrangement in the central control room, a computer room layout drawing, control system explanation drawings, interlock diagrams, and the instrumentation power supply diagrams. (NEDO)

Report on the achievements in the projects subsidized by the Sunshine Project in fiscal 1981. Data 2. Development of a coal liquefaction technology - development of a solvent extraction and liquefaction technology - 'development of a brown coal based solvent extraction plant' (Development of a 50-t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 2). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Developmental researches were carried out on a liquefaction plant for the Victoria brown coal produced in Australia (a 50-t/d pilot plant). In fiscal 1981, detailed design was performed on the primary hydrogenation system by using the process conception and the design data obtained in the element studies. Part of the devices was procured, and the site construction was begun. The present data is a collection of drawings in relation with the machine design, such as the piping specifications, standard piping drawings, piping design procedures, piping drawings, pipe lists, and device inspection specifications. In relation with the instrumentation design, the instrumentation engineering specifications and meter lists. (NEDO)

FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Ocean survey and development of evaluation technology for CO2 sequestration ability); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Assuming the melting and sequestration of CO2 at the intermediate depth of the sea area around Japan, study of evaluation technology of CO2 sequestration ability in ocean was studied, and the FY 1999 results were summed up. In the ocean survey, survey was conducted by ship (No.2 Hakurei-maru) mainly at typical observation points and traverse lines of long. 147 E and long. 155 E. In the survey, the following data were acquired: data on seawater density and chemical tracer, data on release of intermediate-depth/independent buoys, concentration distribution of carbonic acid base substances/nutrient salts/chlorophyll, data on the existing amount of marine organisms and primary production speed measurement experiment, data on experiment on CO2 on-board exposure to organisms in the intermediate depth of ocean, etc. In the measurement/analysis of the sediment particle flux amount, sediment traps were installed/recovered. Further, for the purpose of measuring the neutralizing effect of calcium carbonate, operation test on CaCO{sub 3} melting experimental equipment was conducted in the actual sea area. In the development of a model for evaluation of CO2 sequestration ability, carried out were the improvement of the model using the inverse method, study of the estimated accuracy using the ocean observation data, etc. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - Development of production technology of thin film solar cells. Separate Volume 1. Development of production technology of low cost/large area modules (Investigational study on the commercialization analysis); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu {sup H}akumaku taiyodenchi no seizo gijutsu kaihatsu{sup -} Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Jitsuyoka kaiseki ni kansuru chosa kenkyu) - 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of supporting the study of commercialization of thin film solar cells for electric power use and the study of production technology of thin film solar cells, survey of the technical trend of the thin film solar cell was conducted, and the FY 2000 results were summed up. The typical Si system thin film solar cell is the amorphous Si solar cell, and the quantity production has already started in Japan and abroad. Further, with the aim of making use of characteristics of the amorphous Si solar cell and also making its defects up, the development of Si thin film solar cell using microcrystal Si and polycrystal Si is greatly expected. Among those, attention is paid to the hybrid type that was proposed for the remarkable improvement in the conversion efficiency of amorphous Si solar cell. In the compound thin film system, the Cu(InGa)Se{sub 2}(CiGS) solar cell was put on the market as product by SSI, though the market scale is small. Further, as to the CdTe thin film solar cell, trial manufacture of the large area module was made in view of the housing use. In addition, there was seen great progress in the color sensitized cell and organic semiconducting solar cell mainly in the U.S. and Europe. (NEDO)

Fiscal 1997 basic research on coal resource development (equipment development). Report on R and D of new exploration technology (exploration of medium-depth coal deposits in water areas); 1997 nendo sekitan shigen kaihatsu kiso chosa (kiki kaihatsu hen) hokokusho. Shintansa gijutsu chosa kaihatsu (suiiki chushindoso tansa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the research result on development of new coal exploration technology. For a high-precision and high-resolution reflective seismic exploration system, R and D was made on the exploration technology of several meter in resolution for medium-depth (800m) coal deposits under a lake of 2m deep. As a result, the high-frequency and high-power source (150-200Hz in dominant frequency, 700-800m in penetrability) and the high-frequency and high sensitivity receiver (10-1000Hz in frequency band, 35V/PA in sensitivity) were developed successfully, and the positioning system was improved. The final evaluation of these elementary technologies was carried out through demonstration tests, resulting in satisfactory results. For a high-efficiency trial drilling system, the in-bore trouble prevention system for measurement, processing and analysis of drilling data (drilling length, drilling rate, revolution, bit load, torque) and drilling mud data (charge water pressure, charge/discharge water, density, pH, viscosity) was constructed. The outlook for low-cost measurement and a safety during drilling was thus obtained. (NEDO)

Fiscal 1983 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1983 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

The effort aims to develop a reactor and its peripheral devices and process management technology therefor and to develop chlorosilane hydrogen-reduction process technology as part of the endeavors to develop a low cost production process for silicon for photovoltaic cells for the purpose of building a model plant capable of approximately 10 tons/year in terms of SOG (spin on glass) silicon. A study is made of ten operations (total reaction time of 2,264 hours), and it turns out that the electric power consumption efficiency is near the initially planned value. The yield of Si is, however, but 16.5% which is lower than the initially planned value of 20%. The value is elevated to 18% by raising the reactor temperature. To prevent overcleaning, a reactor with its internal walls experimentally coated with SiC is tested. The problems with devices other than the reactor tube are extraction rendered difficult by anomalously grown granules and processing devices choked by Si powder contained in waste gas after reaction. The first problem is settled by modifying the extraction tube but the other still needs a remedy. The produced granules are found to be high in quality. The seed producing roll crusher is operated for a total of 92 hours yielding 857kg in total. (NEDO)

Fiscal 1982 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1982 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

The effort aims to develop a reactor and its peripheral devices and process management technology therefor and to develop chlorosilane hydrogen-reduction process technology as part of the endeavors to develop a low cost production process for silicon for photovoltaic cells for the purpose of building a model plant capable of approximately 10 tons/year in terms of SOG (spin on glass) silicon. The installation of a 10 tons/year class model plant for SOG-Si production is completed in July 1982. Flaws are removed after a test run, and four reactions are accomplished without damage on the reactor tube in the period from February-end to March-beginning marking 550 hours of operation in total. Thanks to the four operations, 1,086kg of granules are experimentally produced and an electric power consumption rate of 30.6KWH/kg Si is achieved, control of the flowing particle amount by reactor differential pressure is accomplished and the same of the yield by recovered silane liquid composition analysis, and essence is seized of operation control technologies. In an experimental apparatus for seed production, Si is crushed by a roll crusher and then subjected to separation by a quartz-made air elutriator. A high yield of 130kg is obtained after crushing for 75 hours. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1995. 2. Main subject (Part 3. Research and development of a product compatibility indexing technology); 1995 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Honronhen (Seihin tekigosei shihyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This paper describes the product compatibility indexing technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1995. In the environmental compatibility of operating works, development was made on a surveillance operating screen which is said to have high compatibility with human senses and recognition characteristics, and a prospect was obtained on superiority in performance. Improvement was given to the facilities to experiment and measure the mental work load indexes (brain wave and pulse variation and the like). Device and operation compatibility technology requires functional design that can handle how to identify different works and the work features considering changes in experiences and skills of the workers. A computer system was structured for stimulation and task execution as the system to support the environment for indexing experiments. The product compatibility study is in the stage of having structured its framework, rather than performing specific researches. However, when the framework is completed, it will be possible to implement basic guidance presentation for spatial design, and product evaluation for individual persons with arbitrary body forms. In addition, the framework could be utilized as a manual for individual product indexing and design evaluation. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1994. 2. Main issue (Part 1 for research and development of a physiological effect measuring technology); 1994 nendo ningen kankaku keisoku oyo gijutsu no kekyu kaihatsu. 2. Honronhen (Seiriteki eikyo keisoku gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

This research and development was performed on (1) a composite physiological function measuring technology for stress measurement, (2) a contact-free skin temperature measuring technology, and (3) a stress indexing substance measuring technology. With regard to the subject (1), the target for the current fiscal year is to restructure a small restraint-free skin impedance measuring device into a practical device that can be used easily at working sites. In order to achieve the goal, electric power conservation and size reduction were moved forward by improving the circuit design, and stabilized measurement, in which the measurement algorithm is made more intelligent, was realized. With regard to the subject (2), the contact-free skin temperature measurement device having been structured by the previous fiscal year was given improvements in such parts as the infrared and visible image input, image processing, and data indication and sense volume estimation. With respect to the subject (3), the technology was established to measure such stress indexing substances as CS and CA from saliva. Positioning of CS and CA as the stress indexing substance was nearly completed. The stress indexing substance measuring device was tried of structuring the prototype A and prototype B applying the semi-micro specifications for an attempt of clearing the steps toward practically usable device. (NEDO)

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 8. Development of hydrogen production technology; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu seika hokokusho. 8. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was carried out to establish a hydrogen production technology in the electrolysis of water using the solid macromolecular electrolyte method expected to be more efficient and less costly than the conventional hydrogen production methods. In the development of large area electrolysis cell lamination, a lamination comprising ten 2,500cm{sup 2} cells was fabricated, and a value exceeding the target energy efficiency of 90% was achieved. In the fabrication of stacks for hydrogen service stations, a lamination of ten cell stacks of 1,000cm{sup 2} was built, which achieved energy efficiency of not less than 90% at the an electrolysis temperature of 100 degrees C. A hydrogen production plant conceptual design was prepared under the conditions of hydrogen generation amount: 10,000Nm{sup 3}/h, electrode area: 10,000cm{sup 2}/cell, current density: 2.5A/cm{sup 2}, operating temperature: 120 degrees C, cell voltage: 1.705V, total number of cells: 976, stack constitution: 122/stack, and the number of stacks: 8. The result of studies placed the plant construction cost at 2.18-billion yen including building and civil engineering costs, and the hydrogen production unit cost at 28.4 yen/Nm{sup 3}. (NEDO)

Achievement report for fiscal 1981 Sunshine Program on development of practical application technologies for photovoltaic power systems. Test production and verification of solar panels (Development of polycrystalline substrate process technologies); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi panel jikken seisaku kensho (takessho kiban kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Studies are conducted to enlarge the diameter of polycrystalline Si castings and to develop a low-loss slicing method using silicon nitride powder as mold releasing agent. The apparatus for Czochralski's pulling process is improved and tested using SEG (selective epitaxial growth) Si, and now the casting of a 150mm-diameter ingot is feasible. Also, test production of a 94mm-square wafer as specified by NEDO (New Energy and Industrial Technology Development Organization) is successfully carried out. Difficulties in separating the mold releasing agent from the crucible are solved by changing the Si{sub 3}N{sub 4} power solution from PVA (polyvinyl alcohol) to ethyl silicate. The design, manufacture, and installation of the important parts of the system for the mass production of castings are now complete. The crucible is designed to be movable relative to the heater section, and the molten Si is allowed to cool and solidify from the bottom upward. In relation with the development of low-cost wafer manufacturing technologies, low-loss slicing methods are studied. It is concluded that under the current circumstances a multi-blade saw is more promising than the multi-wire saw in view of the damaged slice rate, processing speed, operating cost, and maintainability. (NEDO)

Fiscal 1997 Project related to research and development of global environment industrial technologies. Report on the results of works commissioned for research and development of technology for reducing carbon dioxide emissions; 1997 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu kanren jigyo. Nisanka tanso nado haishutsu teigen gijutsu kenkyu kaihatsu itaku gyomu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective of achieving reduction in emission of carbon dioxide and fluorocarbons, the `research and development on technologies to reduce emission of carbon dioxide and other substances` consisting of eight projects were conducted. In research and development of waste water treatment technologies using submerged combustion, studies were performed on removal by combustion of such pollutants as organic compounds, nitrogen compounds, and sulfur compounds. The development targets were achieved on each item. In research and development related with thermal electric power generation elements, semiconductor single crystals were fabricated in order to acquire technical knowledge on thermal power generation elements intended of utilizing industrial waste heat, whereas a simulation technology for designing was developed. In other projects, research and development works were carried out on high-performance heat insulating materials, and a movable methanol reformer for fuel cells. Developments were conducted on a large pressure reducing valve, and a cooling and heating turbo heat pump for regional air conditioning facilities. Research and development were made on Peltier elements, all efforts having achieved results respectively. 134 figs., 65 tabs.

Fiscal 1999 achievement report. Important regional technology research and development--Research and development of eco-tailored tribo-material creation process technology (Research and development of nanometer-structured material creation process technology); Eco tailored tribo material soisei process gijutsu no kenkyu kaihatsu / nano meter odor de seigyosareta material sosei process gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For a reduction in friction and abrasion of automotive engine piston rings, cams, shims, etc., which grow aggravated due to increasingly severe operating conditions, studies are made to develop a process technology for the creation of tribo-materials through the application of the ion process technology which is capable of controlling nanometer-scale structures. In the study of nano-structure control process, various types of coat forming technologies are employed, which are ion plating, plasma CVD (chemical vapor deposition), and sputtering, for the formation of Ti-Si-N based coatings, Cr-Si-N based coatings, etc. As the result, efforts are now increasingly focused on the arc ion plating technology. In the study of composite tribo-materials, since it is found that high density and high adhesion are achieved in Ti-Si-N based and Cr-Si-N based coatings in particular, their use as coatings for cams, shims, and piston rings is evaluated. In the study of the optimization of matrix layer materials, the sliding characteristics of nitride coatings are investigated, with their formation conditions varied for the control of coating hardness and orientation. (NEDO)

Fiscal 1985 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1985 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

The operation continues of the experimental device capable of producing 10 tons/year of SOG (spun on glass)-Si, and efforts are under way to carry out improvements, to verify such improvements for the results, and to develop operation control technologies. During the operation, improvements are made with respect to the length of stable operation period, granule quality, and device operation, and the results are verified. An automated control test system is verified, and a reactor tube newly developed by Shin-Etsu Chemical Company is subjected to a durability verification test. On the other hand, development is started of SiC-CVD (chemical vapor deposition) technology for materials for large reactor tubes, studies are started on a basic experimental device, basic studies are conducted for designing a large reactor, and investigations are conducted of a large plant conceptual design, an automated control system for reactors, and so forth. The results achieved are all found to be satisfactory. Above all, the granule quality is improved to be quite high in purity, and a cast cell made from improved granules exhibits a photoelectric conversion efficiency to exceed 13%. It is also found that the newly developed reactor tube is stronger than conventional reactor tubes and will be advantageous over others in the future enlargement of devices. (NEDO)

Fiscal 1986 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1986 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-01

The aim is to develop a fluidized bed reactor high in productivity and low in power consumption for the realization of mass production of low cost polycrystalline silicon usable for solar cell construction. An experimental device capable of producing 10 tons/year of SOG (spun on glass)-Si is built and operated. The fluidized bed reactor treating trichlorosilane as the material and the product quality achieve the initially set goals, and the essence is seized of operation management technology. In fiscal 1986, for development of the technology into a practical application technology, designs are prepared for a larger reactor unit and a large plant of the commercial scale. From the viewpoints of production efficiency and cost, the enlargement of a reactor unit is an inevitable task to discharge before practical application. There are two challenges to meet. One is the development of technologies for manufacturing large reactor tubes strong enough to withstand practical service and the other the development of a reactor structure fit for dimensional enlargement. It is then found that the concept of an economically optimum design relative to device series or device block formation is variable in the case of large plants, dependent on the scale of production, and that therefore it is necessary to arrange problems in a proper order to facilitate further deliberation. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 4. Development of motive power generation technology; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 4. Doryoku hassei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-4, the development of a motive power generation technology. The objective is to build a 100-kW class single cylinder hydrogen-argon circulating diesel system. For a hydrogen injection valve being the key to the system, development was made on the conventional hydraulic system with quick compression, expansion, and electronics control. Discussions were given on an exhaust gas condenser and a gas-liquid separator to handle gas mixture with low steam concentration. In order to assure the mechanical strength to deal with the argon working gas, super-chargers and expansion turbines were also discussed. When the hydrogen injection pressure is increased from 20 to 25 MPa in the basic test, the combustion speed has increased, and the indicated thermal efficiency has been improved. The same effect was obtained also when the oxygen/argon ratio was increased. Although the thermal loss increases if the oxygen/argon ratio is increased, the loss in the indicated thermal efficiency is compensated by the gain derived from increasing the combustion speed. When argon is used as the working gas, the temperatures in parts of the combustion chamber rise much higher than that in the case of a light oil diesel system. Therefore, discussions were given on materials and structures that can withstand elevated temperatures, and assessments and tests were performed on high-temperature lubricants. (NEDO)

Fiscal 1987 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1987 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

Since its construction in 1982, the experimental device capable of 10 tons/year production of SOG (spun on glass)-Si has been in operation, and the trichlorosilane processing fluidized bed reactor has achieved its goals in performance and product quality. Element studies continue for the enlargement of the reactor unit for practical application and for the designing of a large plant of the commercially viable scale. In fiscal 1987, element studies are conducted for the enlargement of the reactor unit. Concerning the development of technologies for the manufacture of large reactor tubes strong enough to withstand practical application, efforts are made to strengthen materials for the fabrication of reactor element tubes (230mm and 500mm in diameter), to develop SiC-CVD (chemical vapor deposition) technology to provide reactor tube materials with resistance to corrosion, and to develop a single reactor tube structure indispensable for device enlargement. For the verification of such element technologies, in line with the study of experimental device operation capable of 10 tons/year SOG-Si production, studies are conducted on continuous stable operation technologies for the fluidized bed reactor, maintenance and improvement of product quality, and enhancement of durability of constituent parts and components. (NEDO)

Fiscal 1984 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1984 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

In fiscal 1984, studies are conducted for long-time stabilized operation of the device (extension of reactor tube service life, elimination of flaws in the granule extraction process, control of deposited silicon), improved granule quality (measures to deal with Cu pollution), cost reduction (improvement on yield of silicon after reaction, reduction in electric power consumption rate), and so forth. The results are found to be satisfactory in outline. The problem of strengthening the reactor tube material itself remains to be solved, however, with many knotty issues to settle before practical application. In the effort to deliberate these difficulties, as many as 4,377 hours (reaction hours) in total are spent in fiscal 1984. During the operation, 8.3 tons of granules are produced of which approximately 7 tons are fed to the next stage of processing. The quality of granules produced in this way is stable thanks to efforts to prevent pollution and to prolong continuous reaction time, and is found to satisfy NEDO (New Energy and Industrial Technology Development Organization) specifications. Furthermore, the cast cell and the ribbon cell using thus-produced granules achieve photoelectric conversion rates of 10% and 9%, respectively, thereby meeting the target goal of 9%. (NEDO)

Fiscal 1999 survey report. Important regional technology research and development--Research and development of eco-tailored tribo-material creation process technology (Research and development of micrometer structured material creation process technology); Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu. Micrometer order de seigyosareta material sosei process gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Researches are conducted on the creation of sub-millimeter structured coatings for engine cylinders, valve seats, etc., for the extensive enhancement of performance of tribology-involved parts. In relation to the technology of high-energy pulse laser-aided fabrication of coatings, a coating manufacturing unit is designed and built, and experiments are conducted for the improvement of molten particle generation efficiency and for the formation of coatings by the adhesion of molten Fe and Mo particles onto a cast iron substrate. In the study of abrasion-proof internal surface treatment technology, various sprayed coatings are prepared and checked for the surface reforming effect of laser irradiation, which is for the identification of sprayed coatings which are fit for laser-aided composite surface treatment. In the study of the creation of self-heat generative compounds and the practical application of their bonding feature, the effect is examined of laser irradiation conditions on the hardness and other properties of the surface layer of a hot-pressed Fe{sub 3}Al body with its surface coarseness homogenized by machining. For the analysis of the mechanism of tribological characteristics, coatings are caused to rub against each other in engine oil. (NEDO)

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. Investigative research on solar system (Development, investigation and research of solar heat utilizing system); 1998 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Solar system no chosa kenkyu (taiyonetsu riyo system no gijutsu kaihatsu chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to prepare a strategic technological development program for solar heat utilization, evaluations and discussions were given on solar heat utilization from the viewpoints of 'utilizing applications', 'demand' and 'possibility of the proliferation thereof'. In the solar heat utilization, the cost rising in approximate proportion with scale of the heat utilization must be considered as one of the predestined conditions. What can be conceived as a means to enhance the economic performance by using engineering approaches would include heat storage, elementary technologies for transportation and the standardization thereof, and the scale economy on the production side in mass production. As a required step in which the series of favorable circulation of standardization to mass production, cost reduction and large quantity proliferation can be induced, it is appropriate to assume household use with high calorie unit price as the target. The household area covers room heating and hot water supply, in which the temperature level is much lower than in industrial use. In this area, a system may be established with a conception to use solar heat as the main heat source, and calorific power by fossil fuel as the supplementary heat source. Solar heat utilization may be considered utilizable in foodstuff factories and school lunch supply centers. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1995. 2. Main subject (Part 2. Research and development of an environment compatible indexing technology); 1995 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Honronhen (Kankyo tekigosei shihyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This paper describes the environment compatible indexing technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1995. In an experiment to evaluate subjectivity on compatibility to sound and vibration environments, the background sound was presented three-dimensionally by using a composite acoustic environment presenting device. Psychological effects in different acoustic environments were elucidated. In thermal comfort by living scenes of workers according to a human body thermal model, wide applicability of the model was suggested. In analyzing the model for climate inside apparels, the conditions on skin surface derived from the human body thermal model by each time step and the surrounding environmental conditions were used as the boundary condition. Then, calculation was performed on the apparel thermal model, whose result was used as the boundary condition to solve the subsequent steps. In experimenting and verifying the human body thermal model, the hand calorimeter was found capable to measure heat dissipation efficiently, and useful for simulating the body temperature adjusting mechanism. It is also capable of discussing the role of blood flow played in heat dissipation. For the indexes to evaluate composite environmental compatibility, a fuzzy theory was used to analyze subjectivity volume data of the subjects in order to evaluate effects of warm heat, light beam, and acoustic environment on the workability. (NEDO)

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. Investigative research on solar system (Development, investigation and research of solar heat utilizing system); 1998 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Solar system no chosa kenkyu (taiyonetsu riyo system no gijutsu kaihatsu chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to prepare a strategic technological development program for solar heat utilization, evaluations and discussions were given on solar heat utilization from the viewpoints of 'utilizing applications', 'demand' and 'possibility of the proliferation thereof'. In the solar heat utilization, the cost rising in approximate proportion with scale of the heat utilization must be considered as one of the predestined conditions. What can be conceived as a means to enhance the economic performance by using engineering approaches would include heat storage, elementary technologies for transportation and the standardization thereof, and the scale economy on the production side in mass production. As a required step in which the series of favorable circulation of standardization to mass production, cost reduction and large quantity proliferation can be induced, it is appropriate to assume household use with high calorie unit price as the target. The household area covers room heating and hot water supply, in which the temperature level is much lower than in industrial use. In this area, a system may be established with a conception to use solar heat as the main heat source, and calorific power by fossil fuel as the supplementary heat source. Solar heat utilization may be considered utilizable in foodstuff factories and school lunch supply centers. (NEDO)

Research and development of the industrial basic technologies of the next generation, 'composite materials (fine ceramics)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fine ceramics'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-30

The results of the first phase research and development project for developing fine ceramics as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop fine ceramics of high strength, corrosion resistance, precision and wear resistance, noting their excellent characteristics. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at development of silicon nitride and silicon carbide for synthesis of the stock materials; explosive forming/treating the stock powders; forming, sintering and processing/joining; evaluation of the characteristics; non-destructive testing methods; designs; and evaluation of the parts, among others, as the elementary techniques for production, evaluation and application of the fine ceramic materials. The technical targets of improving functions have been achieved, or bright prospects have been obtained therefor in development of the techniques for synthesis of the stock materials, forming/sintering and processing/joining. The silica reduction for stock synthesis, basic techniques for molding/sintering, and rheological considerations for the molding/sintering techniques represent the techniques of the next generation, because they break through the limitations of the conventional techniques. (NEDO)

FY 1980 Report on results of Sunshine Project. Development of coal liquefaction techniques (Development of materials for the coal liquefaction plant); 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sekitan ekika plant zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

A 1 T/D solvent-extraction type coal liquefaction test plant was constructed and operated to obtain the technical data for the design of, and establish the techniques for, an efficient coal liquefaction plant. The FY 1980 program includes surveys on the materials for coal liquefaction plants, covering those already developed and under development, to clarify the problematical points; drafting the test schedules; and conceptual designs of the material testing facilities. The major problems involved in the materials for coal liquefaction plants include erosion by fluidizing coal slurry, hydrogen embrittlement of the reactor materials, and corrosion by the liquefaction products (e.g., stress-corrosion cracking of austenitic steel, and corrosion by organic acids). The surveys on materials research trends suggest that USA seems to concentrate their research efforts on the reactor materials. The corrosion tests are mostly of in-plant tests, but the stress corrosion and slurry erosion tests are conducted on a laboratory scale. The conceptual designs are drawn for some testing units, e.g., the loop type material testing unit and basic testing unit for jet-spray type slurry erosion. (NEDO)

Industrial science and technology research and development institutions in fiscal 1999. Report on achievements in research and development of human media; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido. Human media no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to give the society with the full picture of human media at an early time, actual problems in industries were taken up. This paper summarizes the sensitivity agent to support sensitivity of individuals, the human media database, the urban environment human media aiming at symbiosis of nature with artificial environment, and the achievements of comprehensive investigations and researches in fiscals 1999 and 2000. Activities were taken in the following four areas: 1) research and development of the sensitivity agent and human media database, 2) research and development of the urban environment human media, 3) comprehensive investigations and researches, and 4) investigations on technological trends in foreign countries. In Item 1), discussions were given on the technology to present full-color images at high accuracy, the image sensitivity retrieval technology, and the multi-dimensional interface technology for the human media database. In studying the basic human media technology, discussions were given on the basic sensitivity modeling technology, and the sensitivity agent mechanism. (NEDO)

Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'Taikankyo kyoka soshi'. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-31

In the research and development of the environment resistance strengthened elements with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments, the second term has developed an integration technology and its evaluation technology based on the achievements in the first term. In developing the heat resistant element technology, the technology to grow {beta}-SiC crystals was expanded to obtaining thin film crystals with high migratory performance by using higher temperatures. At the same time, development was performed on a technology to manufacture multiple number of transistors on one substrate, such as the doping technology and etching technology. Using this technology, schottky diodes and p-n junction elements being the basic structures of MES-FET and bipolar transistors were fabricated. In the evaluation and testing technology, the {gamma} dose measuring method using TLD was improved, the traceability of {gamma} ray irradiation amount was assured, the simplified irradiation testing method using X-ray was established, and the heat resistance testing technology for electronic parts was established. Furthermore, attempts were made on enhancing radiation resistance of the elements, such as in MOS silicon integrated circuit, bipolar silicon integrated circuit, and compound semiconductor integrated circuit. (NEDO)

Research and development of basic technologies for next-generation industry. Evaluation of 1st-phase research and development of 3-dimensional circuit devices; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Sanjigen kairo soshi daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The aim is to develop basic technologies relating to 3-dimensional circuit devices with an ultrahigh-density accumulation of functions therein for the embodiment of ultra-small high-performance data processing devices or artificial brain-like multiple-function data processing devices. To be developed are laminate-structure devices which have an ultrahigh-density accumulation of logic and memory functions or a complex accumulation of functions including signal and sensor functions. In the 1st phase, importance is attached to the development of a multilayer crystalline structure, which is the most elementary in the development of 3-dimensional circuit devices, and of processing technologies for them. Propositions are made and analyses are conducted relating to the enlargement of exposure region in synchrotron radiation lithography, development of a maskless beam process of a resolution of 0.1{mu}m, development of a focused ion beam device, etc. Recrystallization methods using a laser beam or a linear electron beam are developed for the growth of multilayer crystals, and are proved to be effective. The application feasibility of a flat deposition dry process etc. to laminate processing technologies is demonstrated. Concerning integration technologies, some laminated circuit devices are experimentally fabricated, and their behavior is determined. The goals of the 1st phase are found achieved. (NEDO)

FY 1999 report on the results of the R and D of femtosecond technology. Development of ultra-short pulse optoelectronics technology; 1999 nendo femutobyo technology no kenkyu kaihatsu seika hokokusho. Chotan pulse hikari electronics gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The paper described the FY 1999 results of the R and D of femtosecond technology. For the purpose of creating new industrial basement technology which supports the highly information-oriented society in the 21st century, the ultra-high speed electronics technology is indispensable which is beyond speed limits of the existing electronics technology and has new functionality. The ultra-high speed electronics basement technology is established through the R and D of the technology to control the state of light and electronics in the femtosecond time domain (10{sup -15} - 10{sup -12} second). Themes of the R and D are technology to generate/transmit femtosecond optical pulse, technology for control/distribution, and ultra-short pulse optoelectronics common basement technology. In FY 1999, a lot of results were obtained in the following: generation of the pulse train highly repeated at 500GHz in semiconductor laser; 139km transmission of 250fs optical pulse; switching movement at ultra-high speed of 150fs-1.2ps in transition among subbands of GaN base and Sb base materials; DEMUXA movement toward 160-10Gb/s in Mach-Zehnder type optical switch. (NEDO)

Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'taikankyo kyoka soshi'. Daiikki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-30

Research, development and evaluation were performed with an objective of developing environment resistance strengthened elements, with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments. The objective for the first term is to develop the basic technology on element structures required to raise the environment resistance, and the methods of testing them. With regard to heat resistant elements, {beta}-SiC single crystal thin films were formed, and a prospect was obtained on using them as the elements. Regarding MOS integrated circuit, bipolar integrated circuit, and GaAs element, points presenting the largest issue in radiation resistance were noticed according to respective elements. Thus, temperature for gate oxide film formation was lowered, element structures were improved, and gate lengths were decreased to enhance the radiation resistance. For the evaluation test technology, a provisional testing method was prepared for the radiation resistance, a prototype in-situ irradiation testing device was fabricated and so was a prototype high-temperature testing device usable up to 500 degrees C. These achievements lead to a belief that the targets for the first term have been achieved. (NEDO)

Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

FY1999 technological development of wind power generation systems for islands. Development of wind power generation systems in islands; 1999 nendo ritoyo furyoku hatsuden system nado gijutsu kaihatsu. Rito ni okeru furyoku hatsuden system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective of developing wind power generation systems that suit small to medium size islands in Japan, conceptual design was made on a 100-kW class wind mill to satisfy such requirements as no need of large heavy machines, and gust resisting performance. Investigations were performed on sites suitable for demonstration tests thereof. This paper reports the achievements in fiscal 1999. In investigating the site location feasibilities, which took small to medium size islands in Okinawa Prefecture as the discussion objects, environmental investigation, wind condition forecast and investigation, and system linkage investigation were carried out, whereas one point each in three islands were extracted as the promising sites. The system discussion and design called for wind velocity resistance of 80 m/s, system linkage percentage of 40% at maximum, power generation cost of 20 yen per kWh, design life of 20 years, constructability of requiring no large heavy machines, and operation mode of diesel hybrid use. Along with these specifications, conceptual design was performed on the system constituting elements, such as wind mill blades, generators, electric power control devices, and towers. In the blade aerodynamic test, wind tunnel tests were executed by using three types of blade wings. Sample blades were fabricated for the preparation of blade material tests. (NEDO)

FY 1998 annual report on the development of fuel cell power generation techniques. Research and development of solid electrolyte fuel cells (research results); 1998 nendo nenryo denchi gijutsu kaihatsu. Kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 research and development results of solid electrolyte fuel cells. For R and D of the tubular type cell by the wet processing technique, the tests are conducted to evaluate the initial performance and long-term durability for continuous operation of the single tubular cell. For development of the several-kW class modules, computer-aided simulations are conducted. For R and D of material and substrate techniques, the thermal cycle characteristics, cell characteristics and stress of the cell modules are evaluated, in order to evaluate their reliability. The thermal cycle test results indicate that performance of the single-stage cell is unaffected by the thermal cycles. It is found by the stress evaluation that use of the separator plate having a higher thermal expansion coefficient than the electrolyte plate and use of the sealant having a thermal expansion coefficient close to that of the electrolyte plate are effective means to reduce stresses. For the research to reduce costs of the cell materials, their chemical, mechanical and thermal characteristics are evaluated. For the system research, the areas for which the compact systems are suitable and their optimization are studied. (NEDO)

Report for fiscal 1981 of committee on industrial solar system practical application technologies development; 1981 nendo sangyoyo solar system jitsuyoka gijutsu kaihatsu iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

NEDO (New Energy and Industrial Technology Development Organization) has been engaged in the development of technologies for the practical application of industrial solar systems since fiscal 1980, and has a committee established to ensure smooth progress of the endeavor. Outlined in this report are mainly the agendas of the fiscal 1981 committee and working group activities. Taken up at the 1st committee meeting convened on September 18, 1981, were the outline of the results of research conducted in fiscal 1980, plans for fiscal 1981 and their progress, plans for fiscal 1982, presentation at the International Solar Energy Society congress, and the course for system development efforts to follow. The 2nd meeting covered investigations of the actualities of dyeing plants, execution plans for fiscal 1982, and the prospects. The 3rd meeting involved a study of system flow. The cascading heat process working group at its 1st meeting discussed the achievements of fiscal 1980, plans for fiscal 1981 and their progress, plans for fiscal 1982, and presentation at the International Solar Energy Society congress. The 2nd meeting covered execution plans for fiscal 1982, the prospects, and system flow. The fixed heat process working group at its 1st meeting discussed the achievements of fiscal 1980, plans for fiscal 1981 and their progress, plans for fiscal 1982, and the International Solar Energy Society congress. The 2nd meeting took up execution plans for fiscal 1982, the prospects, and system flow. (NEDO)

Report on results of R and D of coal liquefaction technology in fiscal 1981; 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu seika setsumeisho

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper explains the results of development of coal liquefaction technology under the Sunshine Project in fiscal 1981. In connection with solvent extraction and liquefaction, an 1 t/day experimental plant was completed for bituminous coals and operated continuously for 153 hours. An examination also started for the development of a 250 t/day pilot plant. As the element studies, R and D is in progress on the solvent extraction and liquefaction process, solid-liquid separation, secondary hydrogenation, and plant materials. In brown coals, the construction work of a 50 t/day pilot plant started for the purpose of establishing liquefaction technology for brown coal in Victoria State, Australia, with a part of the equipment manufactured. As the element studies, research was conducted on primary hydrogenation, deliming, secondary hydrogenation, dehydration and catalysts. In solvolysis liquefaction, a short-time concluding liquefaction reaction was continuously performed by a plant of 1 t/day scale. In direct hydro-liquefaction, a 2.4 t/day experimental plant was constructed, with the element studies conducted successively. In other words, researches were carried out by the bench scale plant on liquefaction, solid-liquid separation, iron-based catalysts, catalyst and reutilization, motive force recovery system by hydrohoist, and effect of preheating and deaeration. (NEDO)

FY1995 new technology of artificial organ materials which can induce host biocompatibility; 1995 nendo jinko zokiyo seitai kino fukatsukagata sozai no kaihatsu gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

The aim of this project is to produce a highly biocompatible materials for next generation's artificial organs using the following methods: 1, Micromodification of polymer materials. 2, Biocompatible treatment for biological materials. 3, Application of bioabsorbable materials. 4, Bioactive substance immobilization. and 5, Use of autologous tissue as artificial organ materials. As a synthetic polymer material, microporous polyurethane was used for a small diameter vascular prosthesis. The graft with this technology was successfully implanted in rat abdomical aortic position. The graft of 1.5 mm in internal diameter and 10cm in length showed excellent patency with nice endothelialisation. As a biological material, microfibers of collagen was used for a sealing substance of vascular prothesis. The microfibers absorbed a large amount of water, which could prevent blood leakage from the graft wall. The graft showed non-thrombogenic property and excellent host cell affinity, resulted in rapid neointima formation. As to autologous tissue, bone marrow was used, since marrow cells can differentiate into any mesenchimal cells with synthesis of growth factors. Marrow cell transplanted vascular prothesis showed rapid capillary ingrowth. These results indicated that the newly designed materials had suitable properties for materials of next generation's artificial organs. (NEDO)

Survey on construction of the database for new energy technology development. Fuel cell; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As a part of the data related to technological development of new energy, the database for fuel cells was prepared. The major international conferences held in fiscal 1996 were reviewed. As the atmosphere of the whole conference, phosphoric acid fuel cell (PAFC) is in a stage just before practical use, and molten carbonate fuel cell (MCFC) is in a stage of the demonstration study of MW class one. The study on solid oxide fuel cell (SOFC) and polymer electrolyte fuel cell (PEFC) is in considerable progress. In particular, the application of PEFC to automobiles is in real investigation. For the database, kinds and features of various fuel cells, operation principles, system configurations of FC plants, application fields, and characteristics were arranged. Field test examples for public and industrial uses were separately arranged, and in particular, the application examples of PAFC were presented together with developmental conditions of the other fuel cells. Overseas situations were equal to domestic ones, and their marketability was predicted. The Japanese subsidy policy and some U.S. policies were also arranged. 28 refs., 51 figs., 37 tabs.

FY1995 new technology of artificial organ materials which can induce host biocompatibility; 1995 nendo jinko zokiyo seitai kino fukatsukagata sozai no kaihatsu gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

The aim of this project is to produce a highly biocompatible materials for next generation's artificial organs using the following methods: 1, Micromodification of polymer materials. 2, Biocompatible treatment for biological materials. 3, Application of bioabsorbable materials. 4, Bioactive substance immobilization. and 5, Use of autologous tissue as artificial organ materials. As a synthetic polymer material, microporous polyurethane was used for a small diameter vascular prosthesis. The graft with this technology was successfully implanted in rat abdomical aortic position. The graft of 1.5 mm in internal diameter and 10cm in length showed excellent patency with nice endothelialisation. As a biological material, microfibers of collagen was used for a sealing substance of vascular prothesis. The microfibers absorbed a large amount of water, which could prevent blood leakage from the graft wall. The graft showed non-thrombogenic property and excellent host cell affinity, resulted in rapid neointima formation. As to autologous tissue, bone marrow was used, since marrow cells can differentiate into any mesenchimal cells with synthesis of growth factors. Marrow cell transplanted vascular prothesis showed rapid capillary ingrowth. These results indicated that the newly designed materials had suitable properties for materials of next generation's artificial organs. (NEDO)

Report on the results of `the R and D of industrial technology information base arrangement`; `Sangyo gijutsu joho kiban seibi kenkyu kaihatsu` seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In relation to information processing in the open type research information networking, R and D were conducted to establish basic technologies such as grading-up, acceleration, enhancement of efficiency, diversification of application, promotion of usable data accumulation, etc. As to the R and D of software to promote sharing of research information, software was developed which can easily modify and renew management objects for users at research sites, etc., and the target was almost achieved. Concerning the R and D of information supply technology, an approach was presented whereby clients submit bids for each stream of the data requested and the admission decision is made so as to maximize gain of the session under network capacity constraints. Additionally, the R and D were made of software to construct an international information sharing system, a system for multi-lingual I/O, text manipulation and communication, and software for remote use of network based information for scientific computing. 138 refs., 125 figs., 33 tabs.

Investigation on preparing data collections related to new energy technology development. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With an objective to put data related to fuel cells systematically into order, related data were collected comprehensively. Reviewing large international conferences impresses dawn of commercialization in phosphoric acid fuel cells (PAFC), take-off of megawatt-class molten carbonate fuel cells (MCFC), and remarkable advancement in studies on solid oxide fuel cells (SOFC) and polymer electrolyte fuel cells (PEFC). The data collection may be compiled as follows: basic principles, features, operation principles, system configurations, utilization fields, and characteristics were summarized on fuel cell power generation systems using phosphoric acid, polymer, molten carbonate, solid oxide, and alkaline fuel cells; major installation examples in Japan and overseas countries were summarized; investigations were given on developing other fuel cells such as alkaline type and direct methanol type fuel cells; and marketability, subsidies operations in Japan, and states of policy implementation in the U.S.A. were investigated and put into order. 22 refs., 24 figs., 21 tabs.

FY1995 development of novel processes for copper concentrates without producing sulfuric acid; 1995 nendo hiryusan hasseigata no atarashii doshigen shori gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

To develop a novel process for copper concentrates which includes leaching of copper with acidic cupric chloride solutions, aiming at the recovery of sulfur in its elemental form, and leaching of gold from the residue with dissolved bromine. The effect of bromide ions on the leaching of chalcopyrite with 1.0 mol dm{sup -3} CuCl{sub 2} has been investigated at 353 K, and it was found that bromide ions have no influence on the leaching rate and the morphology of elemental sulfur deposited on the surface of chalcopyrite. Dissolved bromine has trivial effects on the morphology and oxidation of porous elemental sulfur covering the residue. However, the dissolved bromine even at 0.02 mol dm-3 depresses the leaching rate of chalcopyrite significantly. Electrotechnical oxidation of cuprous ions, chloride ions and bromide ions in the solution has examined to understand the regeneration of leachant, and it was found that these ions are oxidized simultaneously on the anode surface under the condition of galvanostatic electrolysis, but these oxidants diffuse toward the bulk of solution and react with their reductants. Thus the redox potential of the solution increases gradually showing the temporary stagnation in potential for oxidation of Cu{sup +}, Br{sup -} and Cl{sup -} ions respectively. (NEDO)

Investigation on innovation of technology development by means of strategic energy intelligence; Energy senryakurontekina approach ni yoru gijutsu kaihatsu no kakushin ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of developing the future innovative energy technology, the paper described a strategic point of view. Effects of the energy issue are remarkable on the next generation and thereafter as seen in the finite of energy resource, global-scale environmental changes, the increasing energy demand, natural/social influences of large-scale technology development. If the technological development is going on in the same way as until now, there will appear limits. Relating to the strategies, to seek what energy should be among the strategies, it is necessary to consider not only global-scale problems but particular conditions in Japan (self-sufficiency, international cooperation, creativity, etc.) Also, wisdom and technique are necessary to attain it. Technological development in a wide sense plays a major role in the energy strategy. Technology innovation must be advanced according to the energy strategy. Integrating ideology into the development of energy technology and selecting therefrom developmental subjects which meet the purpose, required is the construction of the energy system with high flexibility and functionality. Looking at the conventional way of thinking from a different angle and posing a future pull plan, Japan should show leadership to the world. 20 refs., 25 figs., 8 tabs.

Trends in coal gasification technology development in the U.S.A. (Volume 2); Beikoku ni okeru sekitan gas ka gijutsu kaihatsu no doko. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

Studies were carried out subsequently from fiscal 1986 on trends in coal gasification technology development in the U.S.A., as a voluntary study of the Coal Utilizing Hydrogen Manufacturing Technology Research Association. In the U.S.A., the governmental organizations and private sectors are working in a body on developing coal technologies. The present survey has seen activities at the Morgan Town Energy Technology Center (METC) being a national research organization, the Institute of Gas Technology Research (IGT) having a long history, and the Great Plains project, a commercialization project. The great accumulation of technologies as the advanced research nation is impressive. In the present study, site surveys were carried out in the U.S.A. in October last year in addition to the surveys made from the aspects of literatures available inside and outside Japan. Section 1 describes the development of the policies of the METC for comprehensive coal gasification research and development, and the development of advanced gasification technologies. Section 2 describes research activities of IGT covering a wide range, the U-Gas process, a plan for the commercial coal gasification plant using Utah coal, and the high-pressure agglomeration (U-gas process). Section 3 describes the summary of the Great Plains coal gasification project and the way to the commercialization thereof. (NEDO)

FY 1999 report on the results of the technology development of next-generation chemical process; 1999 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted on the naphtha catalytic cracking, selective oxidation reaction of saturated hydrocarbon, new reaction mechanism utilization process, etc., as next-generation chemical process technology in FY 1999, and the results were summarized. As to the technology of naphtha catalytic cracking, developed was La203/p/ZMS-5 zeolite catalyst which is high in cracking activity and high in light-olefin selectivity. By the FS, it was confirmed that this is more excellent in case of the fixed bed reactor than in the present process. Concerning the technology of selective oxidation reaction of saturated hydrocarbon, the basic information/knowledge were obtained about the construction of catalytic principle toward the high selective catalytic partial oxidation, elucidation of a reaction mechanism in alkane oxidation and design of high functional catalysts, elucidation of a mechanism in butan oxidation, synthesis of alkane selective oxidation catalysts, etc. In relation to the technology of new reaction mechanism utilization process, the following were carried out: study of ethyl benzene dehydrogenation using the membrane reactor trially fabricated in the previous fiscal year, development of high efficiency hydrogen penetration membranes and low temperature high activity catalysts, study of the new process by membrane reactor. (NEDO)

Fiscal 1998 research achievement report. Project for promoting development of super-advanced electronic technology; 1998 nendo chosentan denshi gijutsu kaihatsu sokushin jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

For the purpose of establishing super-advanced technologies two generations ahead in the field of electronics and information, research and development was carried out involving ultrafine machining process technology, technologies of ultimate measuring, analysis, and control, and technologies of electronic materials equipped with novel functions. In the study of writing systems in which writing is performed directly by an electron beam, writing technologies using electron beams under single-column and multi-column systems were taken up. In the study of ultrashort wavelength electromagnetic wave patterning systems, studies were made about equimultiple ultrashort wavelength and reduced ultrashort wavelength electromagnetic wave patterning. In the study of ultrahigh precision shielding systems, studies involved high precision in situ measurement and control of writing distortion, and ultrahigh precision and high current density electronic optical technologies. Also carried out were research and development of technologies of super-advanced plasma measurement, analysis, and control, technology of cleaning by ultrafine particle control, technology of ultrahigh sensitivity medium, and technologies of new functional elements and film fabrication. In the overall research and survey, surveys were conducted of the trends of development of technology of semiconductor related lithography. (NEDO)

FY1995 new technology of artificial organ materials which can induce host biocompatibility; 1995 nendo jinko zokiyo seitai kino fukatsukagata sozai no kaihatsu gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

The aim of this project is to produce a highly biocompatible materials for next generation's artificial organs using the following methods: 1, Micromodification of polymer materials. 2, Biocompatible treatment for biological materials. 3, Application of bioabsorbable materials. 4, Bioactive substance immobilization. and 5, Use of autologous tissue as artificial organ materials. As a synthetic polymer material, microporous polyurethane was used for a small diameter vascular prosthesis. The graft with this technology was successfully implanted in rat abdomical aortic position. The graft of 1.5 mm in internal diameter and 10 cm in length showed excellent patency with nice endothelialisation. As a biological material, microfibers of collagen was used for a sealing substance of vascular prothesis. The microfibers absorbed a large amount of water, which could prevent blood leakage from the graft wall. The graft showed non-thrombogenic property and excellent host cell affinity, resulted in rapid neointima formation. As to autologous tissue, bone marrow was used, since marrow cells can differentiate into any mesenchimal cells with synthesis of growth factors. Marrow cell transplanted vascular prothesis showed rapid capillary ingrowth. These results indicated that the newly designed materials had suitable properties for materials of next generation's artificial organs. (NEDO)

FY1995 new technology of artificial organ materials which can induce host biocompatibility; 1995 nendo jinko zokiyo seitai kino fukatsukagata sozai no kaihatsu gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

The aim of this project is to produce a highly biocompatible materials for next generation's artificial organs using the following methods: 1, Micromodification of polymer materials. 2, Biocompatible treatment for biological materials. 3, Application of bioabsorbable materials. 4, Bioactive substance immobilization. and 5, Use of autologous tissue as artificial organ materials. As a synthetic polymer material, microporous polyurethane was used for a small diameter vascular prosthesis. The graft with this technology was successfully implanted in rat abdomical aortic position. The graft of 1.5 mm in internal diameter and 10 cm in length showed excellent patency with nice endothelialisation. As a biological material, microfibers of collagen was used for a sealing substance of vascular prothesis. The microfibers absorbed a large amount of water, which could prevent blood leakage from the graft wall. The graft showed non-thrombogenic property and excellent host cell affinity, resulted in rapid neointima formation. As to autologous tissue, bone marrow was used, since marrow cells can differentiate into any mesenchimal cells with synthesis of growth factors. Marrow cell transplanted vascular prothesis showed rapid capillary ingrowth. These results indicated that the newly designed materials had suitable properties for materials of next generation's artificial organs. (NEDO)

FY 1992 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1992 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1992 as the third year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

FY 1991 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1991 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1991 as the second year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

FY 1994 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1994 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

This 5-year joint project (FY 1990 to 1994) by Japan and the Philippines is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized in the Philippines into electric power, in which thermal decomposition/gasification of the wastes is combined with a gas engine system. The field tests of the demonstration plant successfully produce power of 100 kW by burning only the low-calorie gas with a heating value near critical level for self-sustained combustion, obtained by gasification of sawdust by the fluidized gasifier and refined, attaining the object of the project. It is confirmed that a 200 to 300 kW class commercial plant can be designed and constructed basically by scaling up the 100 kW demonstration plant. The other data obtained by the field tests include those for improved operability and maintainability, gas purification, and reducing sizes of the facilities, including utility facilities. (NEDO)

FY 1990 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1990 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1990 as the initial year include negotiations with the Philippines, on-the-spot surveys for the demonstration plant sites and conditions, and conceptual designs of the demonstration plant. (NEDO)