The effect of phase constituent on the magnetic properties for melt-spun Nd15Fe77B8 ribbons

International Nuclear Information System (INIS)

Sun Wensheng; Li Shandong; Quan Mingxiu

1997-01-01

Some acicular Nd 2 Fe 14 B grains are precipitated from Nd-rich phase near-coarse grains in melt-spun Nd 15 Fe 77 B 8 alloy, as confirmed by SEM energy spectral analysis. The Nd-rich phase plays an important role in enhancing magnetic properties on annealing. This result suggests that the melted Nd-rich phase may act as a sink for free iron to be captured within Nd-rich phase regions resulting in the decreased iron constituent and enhanced magnetic properties at the annealing temperature at which the Nd-rich phase is melted. After an optimized heat treatment, the higher magnetic properties with ultrahigh coercivity H c , 1400 kAm -1 , and maximum energy product (BH) max , 89 kJm -3 , are obtained. The initial magnetization curves of melt-spun samples are composed of multi-domain and single-domain magnetization processes. (orig.)

Magnetic properties of centrifugally prepared melt-spun Nd-Fe-B alloys and their powders

International Nuclear Information System (INIS)

Andreev, S.V.; Kudrevatykh, N.V.; Kozlov, A.I.; Markin, P.E.; Pushkarskiy, V.I.

1998-01-01

Magnetic hysteresis properties and microstructure peculiarities of melt spun Nd-Fe-B alloys (ribbons) prepared by melt quenching on to the internal surface of an iron spinning wheel at the tangential speeds in the range 5-20 m/sec are reported. The alloy composition was Nd-36% wt. B-1.2% wt. and Fe-reminder. It was found that the coercivity of ribbons does not practically depend on the wheel speed in the applied range (1430 kA/m at 5 m/sec and 1750 kA/m at 20 m/sec), whereas the grain size of the basic phase (2-14-1) steadily decreases when the speed rises, starting from 2-3 μm for 5 m sec alloy down to the 200-300 nm for 20 m/sec alloy. All ribbons have normal convex demagnetization curves, even those prepared at low wheel speeds (without peculiar step near H∝0, which usually exists on such curves for traditionally prepared underquenched melt-spun Nd-Fe-B alloys). Grinding the ribbons subjected to hydrogen and annealing treatments causes the coercivity drop. However, this operations increase the powder alignment ability and, as a result, the energy product for fully dense magnet from such powder rises to 160-180 kJ/m 3 . (orig.)

Morphological characteristic of the conventional and melt-spun Al-10Ni-5.6Cu (in wt.%) alloy

Energy Technology Data Exchange (ETDEWEB)

Karakoese, Ercan [Erciyes University, Institute of Science and Technology, Department of Physics, 38039 Kayseri (Turkey); Keskin, Mustafa, E-mail: keskin@erciyes.edu.tr [Erciyes University, Faculty of Arts and Sciences, Department of Physics, 38039 Kayseri (Turkey)

2009-12-15

The Al-10Ni-5.6Cu alloy was prepared by conventional casting and further processed melt-spinning technique. The resulting conventional cast and melt-spun ribbons were characterized using X-ray diffraction, optical microscopy, scanning electron microscopy together with energy dispersive spectroscopy, differential scanning calorimetry and microhardness techniques. The X-ray diffraction analysis indicated that ingot samples were {alpha}-Al, intermetallic Al{sub 3}Ni and Al{sub 2}Cu phases. The optical microscopy and scanning electron microscopy results show that the microstructures of rapidly solidified ribbons are clearly different from their ingot alloy. Al-10Ni-5.6Cu ribbons reveal a very fine cellular structure with intermetallic Al{sub 3}Ni particles. Moreover, at high solidification rates the melt-spun ribbons have a polygonal structure dispersed in a supersaturated aluminum matrix. The differential scanning calorimetry measurements revealed that exothermic reaction was between 290 deg. C and 440 deg. C which are more pronounced in the ternary Al-10Ni-5.6Cu alloy.

Morphological characteristic of the conventional and melt-spun Al-10Ni-5.6Cu (in wt.%) alloy

International Nuclear Information System (INIS)

Karakoese, Ercan; Keskin, Mustafa

2009-01-01

The Al-10Ni-5.6Cu alloy was prepared by conventional casting and further processed melt-spinning technique. The resulting conventional cast and melt-spun ribbons were characterized using X-ray diffraction, optical microscopy, scanning electron microscopy together with energy dispersive spectroscopy, differential scanning calorimetry and microhardness techniques. The X-ray diffraction analysis indicated that ingot samples were α-Al, intermetallic Al 3 Ni and Al 2 Cu phases. The optical microscopy and scanning electron microscopy results show that the microstructures of rapidly solidified ribbons are clearly different from their ingot alloy. Al-10Ni-5.6Cu ribbons reveal a very fine cellular structure with intermetallic Al 3 Ni particles. Moreover, at high solidification rates the melt-spun ribbons have a polygonal structure dispersed in a supersaturated aluminum matrix. The differential scanning calorimetry measurements revealed that exothermic reaction was between 290 deg. C and 440 deg. C which are more pronounced in the ternary Al-10Ni-5.6Cu alloy.

Magnetic properties of melt-spun FeMnAlB alloys

International Nuclear Information System (INIS)

Betancourt, I.; Nava, F.

2007-01-01

Magnetic properties of melt spun Fe 89-x Mn 11 Al x (x=2,4,8,15) and Fe 87-y Mn 11 Al 2 By(y=6,8,10) alloy series were studied by vibrating sample magnetometry and complex permeability measurements. The saturation magnetization exhibited an initial high value of 210emu/g followed by a decreasing tendency with increasing Al and B additions (up to 139emu/g). On the other hand, the initial permeability showed variations within the range 1000-2000, whereas the relaxation frequency displayed a maximum of 2MHz for the 4at% Al alloy

Effect of postdrawing temperature on structure, morphology and mechanical properties of melt-spun isotactic polypropylene tapes

NARCIS (Netherlands)

Loos, J.; Schimanski, T.

2005-01-01

Structure, morphology, and mechanical properties of melt-spun and postdrawn isotactic polypropylene (iPP) tapes are analyzed to study the effect of postdraw temperature applied. For affine drawing conditions, i.e., no effective relaxation of the molecules occurs during postdrawing, the Young's

Magnetic hysteresis properties of melt-spun Nd-Fe-B alloys prepared by centrifugal method

International Nuclear Information System (INIS)

Andreev, S.V.; Kudrevatykh, N.V.; Pushkarsky, V.I.; Markin, P.E.; Zaikov, N.K.; Tarasov, E.N.

1998-01-01

Magnetic hysteresis properties and microstructure peculiarities of melt spun Nd-Fe-B alloys (ribbons) prepared by melt quenching onto the internal surface of an iron spinning wheel at tangential speeds in the range 5-20 m/s are reported. The alloy composition was Nd-36% wt, B-1.2% wt. and Fe-remainder. It was found that the coercivity of ribbons does not practically depend on the wheel speed in applied range (18 kOe at 5 m/s and 22 kOe at 20 m/s), whereas the grain size of the basic phase (2-14-1) ste[ily decreases when the speed rises, starting from 2-3 μm for 5 m/s alloy down to the 200-300 nm for 20 m/s alloy. All ribbons have normal convex demagnetization curves, even those prepared at low wheel speeds (without peculiar step near H∝0, which usually exists on such curves for tr[itionally prepared underquenched melt-spun Nd-Fe-B alloys). Grinding the ribbon in a vibration mill causes the coercivity drop to 7 kOe after 120 min of treatment. However, this operation increases the powder alignment ability and, as a result, the energy product for a fully dense magnet from anisotropic powder prepared from some ribbons rises to 20-23 MGOe. (orig.)

Effect of stretching on the mechanical properties in melt-spun poly(butylene succinate)/microfibrillated cellulose (MFC) nanocomposites.

Science.gov (United States)

Zhou, Mi; Fan, Mao; Zhao, Yongsheng; Jin, Tianxiang; Fu, Qiang

2016-04-20

In order to prepare poly(butylene succinate)/microfibrillated cellulose composites with high performance, in this work, microfibrillated cellulose (MFC) was first treated by acetylchloride with ball-milling to improve its interfacial compatibility with poly(butylene succinate) (PBS). Then melt stretching processing was adopted to further improve the dispersion and orientation of MFC in as-spun PBS fiber. And the effect of MFC on the crystalline structure and mechanical properties were systematically investigated for the melt-spun fibers prepared with two different draw ratios. The dispersion, alignment of the MFC and interfacial crystalline structure in the composite fibers are significantly influenced by the stretching force during the melt spinning. The possible formation of nanohybrid shish kebab (NHSK) superstructure where aligned MFC as shish and PBS lamellae as kebab has been suggested via SEM and SAXS in the composite fibers prepared at the high draw ratio. Large improvement in tensile strength has been realized at the high draw ratio due to the enhanced orientation and dispersion of MFC as well as the formation of NHSK. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of boron additions on phase formation and magnetic properties of TbCu7-type melt spun SmFe ribbons

International Nuclear Information System (INIS)

Zheng, Chuanjiang; Yu, Dunbo; Li, Kuoshe; Luo, Yang; Jin, Jinling; Lu, Shuo; Li, Hongwei; Mao, Yongjun; Quan, Ningtao

2016-01-01

Melt spun ribbons of a series of SmFe 12 B x (x=0.0, 0.5, 0.75, 1.0, 1.25, and 1.5) have been prepared by the melt spinning technique. Sm–Fe–B melt spun ribbons with single phase TbCu 7 -type structure were prepared from the SmFe 12 B x (x=0.5, 0.75, and 1.0) alloys at the surface velocity around 40 m/s. The addition of boron not only inhibits the appearance of soft magnetic phase α-Fe, but also enhances the ability of amorphous formation for melt spun Sm–Fe ribbons. The concentration of boron atoms, however, exceeds the limit of the solubility (x>1.0) of Sm–Fe alloys, which does not impede the appearance of α-Fe but accelerates the formation of metastable phase Sm 2 Fe 23 B 3 that is unfavorable to their magnetic properties. Moreover, it is found that the addition of boron whose concentration is 0.0≤x≤0.75 can stabilize the metastable TbCu 7 -type structure because of the increase of the lattice parameter ratio c/a. The magnetic properties of as-annealed SmFe 12 B 1.0 melt spun ribbons with an energy product of 2.19MGOe, a coercivity of 2.36 kOe and a remanence of 4.8 kGs have been achieved. The microstructural characteristics of as-annealed melt spun SmFe 12 and SmFe 12 B 1.0 ribbons have been discussed as well. The following sequence of the hyperfine field H(6l)melt spun Sm–Fe alloys with TbCu 7 -type structure, and the metastable phase Sm 2 Fe 23 B 3 will appear when the content of boron

The dry-heat loss effect of melt-spun phase change material fibres.

Science.gov (United States)

Tjønnås, Maria Suong; Færevik, Hilde; Sandsund, Mariann; Reinertsen, Randi E

2015-01-01

Phase change materials (PCM) have the ability to store latent heat when they change phases, a property that gives clothing that incorporates PCM its cooling effect. This study investigated the effect of dry-heat loss (cooling) of a novel melt-spun PCM fibre on the basis of the area covered, mass, the latent heat of fusion and melting temperature, compared to a known PCM clothing product. PCM fibres with melting temperatures of 28.4 and 32.0°C and PCM packs with melting temperatures of 28.0 and 32.0°C were studied. The results showed that the PCM fibres had a larger initial peak cooling effect than that of the PCM packs. The duration of the cooling effect of PCM fibres was primarily dependent on the PCM mass and the latent heat of fusion capacity, and secondly on the covered area and melting temperature of the PCM. This study investigates the cooling effect of PCM fibres on a thermal manikin. The PCM fibres had a high but short-lasting cooling effect. This study contributes to the knowledge of how the body's temperature regulation may be affected by the cooling properties of clothing that incorporates PCM.

Effect of boron additions on phase formation and magnetic properties of TbCu{sub 7}-type melt spun SmFe ribbons

Energy Technology Data Exchange (ETDEWEB)

Zheng, Chuanjiang; Yu, Dunbo, E-mail: yudb2008@126.com; Li, Kuoshe; Luo, Yang; Jin, Jinling; Lu, Shuo; Li, Hongwei; Mao, Yongjun; Quan, Ningtao

2016-08-15

Melt spun ribbons of a series of SmFe{sub 12}B{sub x} (x=0.0, 0.5, 0.75, 1.0, 1.25, and 1.5) have been prepared by the melt spinning technique. Sm–Fe–B melt spun ribbons with single phase TbCu{sub 7}-type structure were prepared from the SmFe{sub 12}B{sub x} (x=0.5, 0.75, and 1.0) alloys at the surface velocity around 40 m/s. The addition of boron not only inhibits the appearance of soft magnetic phase α-Fe, but also enhances the ability of amorphous formation for melt spun Sm–Fe ribbons. The concentration of boron atoms, however, exceeds the limit of the solubility (x>1.0) of Sm–Fe alloys, which does not impede the appearance of α-Fe but accelerates the formation of metastable phase Sm{sub 2}Fe{sub 23}B{sub 3} that is unfavorable to their magnetic properties. Moreover, it is found that the addition of boron whose concentration is 0.0≤x≤0.75 can stabilize the metastable TbCu{sub 7}-type structure because of the increase of the lattice parameter ratio c/a. The magnetic properties of as-annealed SmFe{sub 12}B{sub 1.0} melt spun ribbons with an energy product of 2.19MGOe, a coercivity of 2.36 kOe and a remanence of 4.8 kGs have been achieved. The microstructural characteristics of as-annealed melt spun SmFe{sub 12} and SmFe{sub 12}B{sub 1.0} ribbons have been discussed as well. The following sequence of the hyperfine field H(6l)melt spun Sm–Fe alloys with TbCu{sub 7}-type structure, and the

Characterisation of melt spun Ni-Ti shape memory Ribbons' microstructure

Science.gov (United States)

Mehrabi, Kambiz; Brunčko, Mihael; Kneissl, Albert C.; Čolič, Miodrag; Stamenković, Dragoslav; Ferčec, Janko; Anžel, Ivan; Rudolf, Rebeka

2012-06-01

NiTi alloys are the most technologically important medical Shape Memory Alloys in a wide range of applications used in Orthopaedics, Neurology, Cardiology and interventional Radiology as guide-wires, self-expandable stents, stent grafts, inferior vena cava filters and clinical instruments. This paper discusses the use of rapid solidification by the melt spinning method for the preparation of thin NiTi ribbons for medical uses. Generally, the application of rapid solidification via melt-spinning can change the microstructure drastically, which improves ductility and shape memory characteristics and leads to samples with small dimensions. As the increase in the wheel speed led to a reduced ribbon thickness, the cooling rate increased and, therefore, the martensitic substructure became finer. Furthermore, no transition from the crystalline phase to the amorphous phase was obtained by increasing the cooling rate, even at a wheel speed of 30 m/s. Specimens for our metallographic investigation were cut from the longitudinal cross sections of melt-spun ribbons. Conventional TEM studies were carried out with an acceleration voltage of 120 kV. Additionally, the chemical composition of the samples was examined with a TEM equipped with an EDX analyser. The crystallographic structure was determined using Bragg-Brentano x-ray diffraction with Cu-Kα radiation at room temperature.

Evolution of the microstructure and magnetic properties of as-cast and melt spun Fe2NiAl alloy during aging

International Nuclear Information System (INIS)

Menushenkov, V.P.; Gorshenkov, M.V.; Shchetinin, I.V.; Savchenko, A.G.; Savchenko, E.S.; Zhukov, D.G.

2015-01-01

Fe 2 NiAl-based alloy with the nominal composition Fe 51.1 Ni 23.5 Al 23.7 Si 1.7 was prepared by casting and melt-spinning. Comparison of the phase composition, microstructure and magnetic properties of water-quenched bulk samples and melt spun ribbons after isothermal aging in the 500–900 °C range were carried out. TEM investigations of the decomposition of the solid solution into β- and β 2 phases during cooling or quenching and subsequent aging have revealed different types of decomposition products. The optimal periodic modulated structure with coercive force H c ~700 Oe was observed after cooling of as-cast alloy at a critical rate. In this structure the paramagnetic β 2 phase forms a continuous network that isolates elongated single domain ferromagnetic β particles. The water-quenched bulk samples and melt spun ribbons were characterized by zone structure with zones about 10 nm and 4 nm in size. The isothermal aging of quenched samples resulted in the formation of modulated microstructure dissimilar to those of the optimal state. The coarsening of ferromagnetic β particles as well as deterioration of the magnetic insulation of β particles occur in bulk samples after aging at T ag >700 °C that decreases H c ≤350 Oe. The dependence δ M (H) was measured and negative values of δ M (H) in the H=0–2000 Oe range indicate that magnetostatic interactions between the β particles are dominant. The melt spun ribbons were characterized by the presence of antiphase domain boundaries (APD) and discontinuous precipitation (DP) products at grain boundaries (GB). The cellular areas at GBs consisting of alternating lamellas of β′- and β 2 ′ type phases were formed after aging the ribbons at T ag >500 °C. At T ag >700 °C the modulated structure formed inside grains and the wide intergranular double-layer of β and β 2 phases develops by the coalescence of the primary DP products that decrease H c ≤250 Oe. MFM image of the magnetic structure

Structural and Electrical Properties Characterization of Sb1.52Bi0.48Te3.0 Melt-Spun Ribbons

Directory of Open Access Journals (Sweden)

Viktoriia Ohorodniichuk

2017-06-01

Full Text Available Melt-spinning (MS has been reported as a promising tool to tailor the microstructure of bulk thermoelectric materials leading to enhanced thermoelectric performances. Here, we report on a detailed characterization of p-type Bi0.48Sb1.52Te3 ribbons produced by melt-spinning. The microstructure of the melt-spun ribbons has been studied by means of X-ray diffraction, scanning and transmission electron microscopy (TEM. The analyses indicate that the ribbons are highly-textured with a very good chemical homogeneity. TEM reveals clear differences in the microstructure at large and short-range scales between the surface that was in contact with the copper wheel and the free surface. These analyses further evidence the absence of amorphous regions in the melt-spun ribbons and the precipitation of elemental Te at the grain boundaries. Low-temperature electrical resistivity and thermopower measurements (20–300 K carried out on several randomly-selected ribbons confirm the excellent reproducibility of the MS process. However, the comparison of the transport properties of the ribbons with those of bulk polycrystalline samples of the same initial composition shows that MS leads to a more pronounced metallic character. This difference is likely tied to changes in deviations from stoichiometry due to the out-of-equilibrium conditions imposed by MS.

Comparative study of crystallized melt-spun iron-boron alloys by Moessbauer effect and resistivity measurements

International Nuclear Information System (INIS)

Arshad, M.; Siddique, M.; Anwar-ul-Islam, M.; Butt, N.M.; Ashfaq, A.; Shamim, A.

1993-01-01

Moessbauer study of two as-quenched, melt-spun iron-boron completely crystallized alloys, Fe/sub 72/01/B/sub 28/ and Fe/sub 88/01/B/sub 12/, indicates the presence of alpha-Fe, Fe/sub 2/B and Fe/sub 3/B. The percentage of these phases is different in the two alloys. Resistivity measurements show to phase transformation of Fe/sub 3/B and Fe/sub 2/B, respectively. (author)

Structure and properties of melt-spun high acrylonitrile copolymer fibers via continuous zone-drawing and zone-annealing processes

International Nuclear Information System (INIS)

Wu Zongquan; Zhang Anqiu; Percec, Simona; Jin Shi; Jing, Alexander J.; Ge, Jason J.; Cheng, Stephen Z.D.

2003-01-01

Continuous zone-drawing and zone-annealing processes have been utilized to probe improvements in mechanical performance of melt-spun high acrylonitrile copolymer fibers (AMLON TM ). The as-spun fibers were zone-drawn at different ratios in a narrow temperature range of 100-105 deg. C and then zone-annealed. As a result of these processes, the fibers show substantial increases in tensile strength and tensile modulus (about three times) and significant improvements in elongation-at-break (about two times) after zone annealing. The thermal transition behavior, dimensional stability and dynamic relaxation properties of the as-spun, zone-drawn and zone-annealed fibers have been studied using differential scanning calorimetry, thermal mechanical and dynamic mechanical experiments. Their mechanical and thermal property changes after the zone-drawing and zone-annealing processes can be associated with the microscopic structural evolution including crystallinity, crystal orientation and apparent crystallite size detected by wide angle X-ray diffraction experiments

Magnetic properties and microstructure of as-spun Fe3B/Nd2Fe14B nanocomposite permanent magnets produced by low-speed melt spinning technique

International Nuclear Information System (INIS)

Hirosawa, S.; Kanekiyo, H.; Ping, D.H.; Hono, K.

1998-01-01

Thick permanent magnet flakes of Fe 3 B/Nd 2 Fe 14 B nanocomposites have been produced directly from molten alloys by means of the low surface-velocity melt spinning technique. The thickness of the flakes varies from 70 to 300 μm depending on the surface velocity (V s ) of a quenching copper roll. Melt-spun flakes of Nd 4 Fe 77.5 B 18.5 alloy exhibit the intrinsic coercivity of 276 kA/m at V s of 5 m/s. X-ray diffraction and transmission electron microscopy results have revealed that this material is composed of nanocrystalline Fe 3 B and Nd 2 Fe 14 B grains ranging from 10 to 50 nm in diameter. The melt-spun alloy produced at V s = 3 m/s contains large grains of Nd 2 Fe 14 B, small grains of Fe 3 B, and large dendritic α-Fe of a few μm in length. In contrast, at V s = 7 m/s, a large portion of the quenched alloy is amorphous. These melt-spun alloys do not possess a hard magnetic property. We have also found that small additions of additives affect the optimum range of V s that give rise to hard magnetic properties in the as-melt-spun condition. Cr has a large effect in shifting the optimum V s values down to a 2-3 m/s range. Simultaneous addition of Co and Ga is effective in extending the optimum values of V s . A platelet permanent magnet with a thickness of 240 μm and magnetic properties of (BH) max = 131 kJ/m 3 , H cJ = 400 kA/m, and B r = 1.15 T has been produced from a Nd 3.5 Dy 1 Fe 73 Co 3 Ga 1 B 18.5 alloy. (orig.)

Evolution of the microstructure and hardness of a rapidly solidified/melt-spun AZ91 alloy upon aging at different temperatures

International Nuclear Information System (INIS)

Wang Baishu; Liu Yongbing; An Jian; Li Rongguang; Su Zhenguo; Su Guihua; Lu You; Cao Zhanyi

2009-01-01

The effect of aging at different temperatures on a rapidly solidified/melt-spun AZ91 alloy has been investigated in depth. The microstructures of as-spun and aged ribbons with a thickness of approximately 60 μm were characterized using X-ray diffraction, transmission electron microscopy and laser optical microscopy; microhardness measurements were also conducted. It was found that the commercial AZ91 alloy undergoes a cellular/dendritic transition during melt-spinning at a speed of 34 m/s. A strengthening effect due to aging was observed: a maximum hardness of 110 HV/0.05 and an age-hardenability of 50% were obtained when the ribbon was aged at 200 deg. C for 20 min. The β-Mg 17 Al 12 phase exhibits net and dispersion types of distribution during precipitation. The dispersion of precipitates in dendritic grains or cells is the main source of strengthening

Non-equilibrium magnetic properties of melt-spun Nd60Fe30Al10 alloys

International Nuclear Information System (INIS)

Sato Turtelli, R.; Sinnecker, J.P.; Steiner, W.; Wiesinger, G.; Groessinger, R.; Triyono, D.

2003-01-01

The temperature, frequency and DC-field dependence of the AC-susceptibility has been investigated on melt-spun Nd 60 Fe 30 Al 10 . The temperature dependence of the AC-susceptibility shows an anomalous behavior, which depends strongly on the applied heat treatment and exhibits a cluster-like characteristic. Similar to the time dependence of the coercivity, a magnetic after-effect is present for temperatures higher than 50 K. 57 Fe Moessbauer spectra can be analyzed by two hyperfine field distributions pointing to two phases with quite different magnetic moments on the Fe sites

Evolution of the microstructure and magnetic properties of as-cast and melt spun Fe{sub 2}NiAl alloy during aging

Energy Technology Data Exchange (ETDEWEB)

Menushenkov, V.P., E-mail: menushenkov@gmail.com; Gorshenkov, M.V.; Shchetinin, I.V.; Savchenko, A.G.; Savchenko, E.S.; Zhukov, D.G.

2015-09-15

Fe{sub 2}NiAl-based alloy with the nominal composition Fe{sub 51.1}Ni{sub 23.5}Al{sub 23.7}Si{sub 1.7} was prepared by casting and melt-spinning. Comparison of the phase composition, microstructure and magnetic properties of water-quenched bulk samples and melt spun ribbons after isothermal aging in the 500–900 °C range were carried out. TEM investigations of the decomposition of the solid solution into β- and β{sub 2} phases during cooling or quenching and subsequent aging have revealed different types of decomposition products. The optimal periodic modulated structure with coercive force H{sub c}~700 Oe was observed after cooling of as-cast alloy at a critical rate. In this structure the paramagnetic β{sub 2} phase forms a continuous network that isolates elongated single domain ferromagnetic β particles. The water-quenched bulk samples and melt spun ribbons were characterized by zone structure with zones about 10 nm and 4 nm in size. The isothermal aging of quenched samples resulted in the formation of modulated microstructure dissimilar to those of the optimal state. The coarsening of ferromagnetic β particles as well as deterioration of the magnetic insulation of β particles occur in bulk samples after aging at T{sub ag}>700 °C that decreases H{sub c}≤350 Oe. The dependence δ{sub M}(H) was measured and negative values of δ{sub M}(H) in the H=0–2000 Oe range indicate that magnetostatic interactions between the β particles are dominant. The melt spun ribbons were characterized by the presence of antiphase domain boundaries (APD) and discontinuous precipitation (DP) products at grain boundaries (GB). The cellular areas at GBs consisting of alternating lamellas of β′- and β{sub 2}′ type phases were formed after aging the ribbons at T{sub ag}>500 °C. At T{sub ag}>700 °C the modulated structure formed inside grains and the wide intergranular double-layer of β and β{sub 2} phases develops by the coalescence of the primary DP products that

Microstructure of the Ni–Fe–Cu–P melt-spun ribbons produced from the single-chamber and from the double-chamber crucibles

Energy Technology Data Exchange (ETDEWEB)

Ziewiec, Krzysztof, E-mail: kziewiec@up.krakow.pl [Institute of Technology, Faculty of Mathematics, Physics and Technical Science, Pedagogical University of Cracow, ul. Podchorążych 2, PL-30-084 Kraków (Poland); Błachowski, Artur; Ruebenbauer, Krzysztof [Mössbauer Spectroscopy Division, Institute of Physics, Pedagogical University, ul. Podchorążych 2, PL-30-084 Kraków (Poland); Ziewiec, Aneta [AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Al. A. Mickiewicza 30, 30-059 Kraków (Poland); Prusik, Krystian [Faculty of Computer Science and Materials Science, University of Silesia, ul. Bankowa 12, PL-40-007 Katowice (Poland); Latuch, Jerzy [Warsaw University of Technology, Faculty of Materials Science and Engineering, ul. Wołoska 141, PL-02-507 Warszawa (Poland); Zięba, Marcin; Bryła, Krzysztof [Institute of Technology, Faculty of Mathematics, Physics and Technical Science, Pedagogical University of Cracow, ul. Podchorążych 2, PL-30-084 Kraków (Poland)

2014-12-05

Highlights: • A new method for production of metallic amorphous/amorphous composite is proposed. • The unique microstructure was obtained by rapid cooling of the two unmixed liquids. • The composite TCMS Ni–Fe–Cu–P amorphous alloy forms ductile fracture. - Abstract: The aim of the work was to investigate the influence of the processing on the final microstructure and properties of the melt-spun Ni–Fe–Cu–P, Ni–Fe–P and Ni–Cu–P alloys ejected in two ways. In the first case, the alloy was molten in a simple single-chamber crucible, then ejected as uniform liquid. In the second case the double-chamber crucible was used, and the flux composed of the two Ni–Fe–P and Ni–Cu–P liquids was cooled on a copper roller before forming a uniform mixture. The two component melt spinning (TCMS) was performed starting from the Ni{sub 40}Fe{sub 40}P{sub 20} and Ni{sub 70}Cu{sub 10}P{sub 20} alloys. Three of the alloys i.e. Ni{sub 55}Fe{sub 20}Cu{sub 4}P{sub 20}, Ni{sub 40}Fe{sub 40}P{sub 20} and Ni{sub 70}Cu{sub 10}P{sub 20} were melt-spun from the traditional single-chamber crucible. The methods applied in this study for microstructural investigations include scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and Mössbauer spectroscopy. Thermal stability of the melt-spun alloys was tested using differential scanning calorimetry (DSC). The results of the investigations are described and discussed in terms of the unique features of the TCMS amorphous microstructure. It is shown that this complex phase composition of the amorphous alloy favors formation of the ductile fracture and the multiple shear band formation.

The microstructure and magnetic properties of melt-spun Fe 76Nd 16B 8 magnetic materials

Science.gov (United States)

Hadjipanayis, G. C.; Dickenson, R. C.; Lawless, K. R.

1986-02-01

The origin of magnetic hardening has been examined in melt-spun Fe 76Nd 16B 8 samples heat-treated at around 700°C. Microstructure studies show the same phases as in sintered magnets consisting of Fe 14Nd 2B, Fe 4NdB 4 and two high-Nd content phases. These phases exist in both equiaxed and faceted crystallites of submicron size. Lorentz microscopy shows domain walls which end at grain boundaries indicating that they are pinned there.

Controlling the microstructure and associated magnetic properties of Ni0.2Mn3.2Ga0.6 melt-spun ribbons by annealing

Directory of Open Access Journals (Sweden)

Mahmud Khan

2017-05-01

Full Text Available Here we report on the structural and magnetic properties of Ni0.2Mn3.2Ga0.6 melt-spun ribbons. The as-spun ribbons were found to exhibit mixed cubic phases that transform to non-cubic structure upon annealing. Additionally, an amorphous phase was found to co-exist in all ribbons. The SEM images show that minor grain formation occurs on the as-spun ribbons. However, the formation of extensive nano-grains was observed on the surfaces of the annealed ribbons. While the as-spun ribbons exhibit predominantly paramagnetic behavior, the ribbons annealed under various thermal conditions were found to be ferromagnetic with a Curie temperature of about 380 K. The ribbons annealed at 450 °C for 30 minutes exhibit a large coercive field of about 2500 Oe. The experimental results show that the microstructure and associated magnetic properties of the ribbons can be controlled by annealing techniques. The coercive fields and the shape of the magnetic hysteresis loops vary significantly with annealing conditions. Exchange bias effects have also been observed in the annealed ribbons.

Crystal structure and magnetic properties of a nitrogenated melt-spun Sm[sub 2]Fe[sub 17] compound

Energy Technology Data Exchange (ETDEWEB)

Yang, Choong-Jin [Electromagnetic Materials Laboratory, Research Institute of Industrial Science and Technology, P.O. Box 135, 790-330 Pohang (Korea, Republic of); Lee, Woo-Young [Electromagnetic Materials Laboratory, Research Institute of Industrial Science and Technology, P.O. Box 135, 790-330 Pohang (Korea, Republic of); Choi, Seung-Duck [Electromagnetic Materials Laboratory, Research Institute of Industrial Science and Technology, P.O. Box 135, 790-330 Pohang (Korea, Republic of)

1994-05-15

Sm[sub 2]Fe[sub 17]N[sub 2.9] compound powders were prepared from parent alloys of Sm[sub 2]Fe[sub 17] which were made by both arc melting and rapid solidification processes. The cast Sm[sub 2]Fe[sub 17] contained mixed phases of SmFe[sub 3] and [alpha]-Fe, and correspondingly formed less Sm[sub 2]Fe[sub 17]N[sub x] with a rather large amount of residual [alpha]-Fe after nitrogenation. The melt-spun Sm[sub 2]Fe[sub 17] compound, however, was single phase and exhibited a negligible amount of residual [alpha]+Fe after nitrogenation. The residual amount of free iron was found to increase as a function of milling time and to impede the development of promising permanent magnetic properties. The melt-spun Sm[sub 2]Fe[sub 17]N[sub x] compound powders exhibited a coercivity value [sub i]H[sub c] of 5 kOe, which is double that of the as-cast Sm[sub 2]Fe[sub 17]N[sub x] powders and a high remanence B[sub r]=60 e.m.u. g[sup -1]. The average magnetic moment of Fe atoms in the crystal is estimated to be 2.29 [mu][sub B] and the Fe atom in the 6c site exhibits the highest magnetic moment of 2.65 [mu][sub B]. The expansion in the c axial direction of the nitrogenated crystal was found to be mainly due to extension of Sm(6c)-Fe(c) and Fe(18f)-Fe(18f) distances. ((orig.))

Effect of precipitation on the shape memory effect of Ti50Ni25Cu25 melt-spun ribbon

International Nuclear Information System (INIS)

Tong Yunxiang; Liu Yong; Xie Zeliang; Zarinejad, Mehrdad

2008-01-01

The present research aims to provide accurate understanding of the relation between precipitation (volume fraction, morphology, type) and shape memory effect of Ti 50 Ni 25 Cu 25 melt-spun ribbon. Rapid thermal annealing was used to control the microstructural development while the shape memory effect of the ribbon was determined under constraint thermal cycling. The results show that the precipitation process takes the following sequence: B11 TiCu → B11 TiCu + Ti 2 (Ni, Cu) → Ti 2 (Ni, Cu) with increasing annealing temperature or duration. The shape memory effect is found to depend on both the volume fraction and the distribution of the precipitates. The former affects the shape recovery strain through reduction of the transformation volume participating the shape recovery. The latter affects the shape recovery strain through strengthening the matrix thus reducing the martensite strain which is more predominant under low constraint stresses. Precipitation strengthening, on the other hand, reduces the tendency of dislocation generation/movement, thus reducing the irreversible strain and improving shape recovery strain. This understanding provides guidelines on the optimization of the shape memory properties of the Ti 50 Ni 25 Cu 25 melt-spun ribbon via post-processing annealing

Microstructure and magnetic properties of melt-spun Alnico-5 alloys

International Nuclear Information System (INIS)

Löwe, Konrad; Dürrschnabel, Michael; Molina-Luna, Leopoldo; Madugundo, Rajasekhar; Frincu, Bianca; Kleebe, Hans-Joachim; Gutfleisch, Oliver; Hadjipanayis, George C.

2016-01-01

The aim of this work is to investigate the effect of very fine grain sizes on the spinodal decomposition in the Alnico system. Commercial Alnico 5 was melted and melt-spun with varying copper wheel speeds, which led to a grain size of 1–2 µm. This value was further reduced to sub-micrometer size by a small addition of Boron (1 at%). The spinodal decomposition was induced through a two-step annealing treatment under magnetic field in the range of 600–900 °C. It was found that the size of the spinodal structures is not influenced much by increased wheel speeds but becomes smaller with the addition of Boron. However, the difference in coercivity between the samples with and without Boron is only 50 Oe (4 kA/m). To study the influence of the annealing treatment two sets of samples are compared, one with the highest coercivity (366 Oe/29 kA/m) and the other one with lower coercivity (180 Oe/14.5 kA/m). We found with Scanning transmission electron microscopy Energy-dispersive X-ray spectroscopy (STEM EDX) a much sharper chemical interface between the α1 and α2 precipitates in the former sample, which we attribute to be the main reason for the higher coercivity. - Highlights: • The influence of various parameters on spinodal decomposition in Alnico is studied. • Through addition of Boron the spinodal features became significantly smaller. • High coercivity samples show a sharp chemical contrast between α1 and α2 lamellae.

The electrochemical properties of melt-spun Al-Si-Cu alloys

International Nuclear Information System (INIS)

Zhang Linping; Wang Fei; Liang Pu; Song Xianlei; Hu Qing; Sun Zhanbo; Song Xiaoping; Yang Sen; Wang Liqun

2011-01-01

Highlights: → Non-equilibrium Al 75-X Si 25 Cu X alloys exhibit high lithiation storages. → The lithiation mechanism is different from melt-spun Al-Si-Mn system. → The structural evolution is mitigated in the non-equilibrium alloys. → Volume variation is alleviated due to the co-existence of Al 2 Cu, α-Si and α-Al. - Abstract: Melt spinning was used to prepare Al 75-X Si 25 Cu X (X = 1, 4, 7, 10 mol%) alloy anode materials for lithium-ion batteries. A metastable supersaturated solid solution of Si and Cu in fcc-Al, α-Si and Al 2 Cu co-existed in the alloys. Nano-scaled α-Al grains, as the matrix, formed in the as-quenched ribbons. The Al 74 Si 25 Cu 1 and Al 71 Si 25 Cu 4 anodes exhibited initial discharge specific capacities of 1539 mAh g -1 , 1324 mAh g -1 and reversible capacities above 472 mAh g -1 , 508 mAh g -1 at the 20th cycle, respectively. The specific capacities reduced as the increase of the Cu content. AlLi intermetallic compound was detected in the lithiated alloys. It is concluded that the lithiation mechanism of the Al-Si-based alloys can be affected by the third component. The structural evolution and volume variation can be mitigated due to the formation of non-equilibrium state and the co-existence of nano-scaled α-Al, α-Si, and Al 2 Cu for the present alloys.

Two directional microstructure and effects of nanoscale dispersed Si particles on microhardness and tensile properties of AlSi7Mg melt-spun alloy

Energy Technology Data Exchange (ETDEWEB)

Dong, Xixi, E-mail: dongxx09@mails.tsinghua.edu.cn [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); He, Liangju [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); School of Aerospace, Tsinghua University, Beijing 100084 (China); Mi, Guangbao [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); Li, Peijie [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China)

2015-01-05

Highlights: • Both surface and cross-sectional microstructure of AlSi7Mg ribbon were characterized. • 13–50 nm and 50-hundreds of nm Si particles were dispersed both in α-Al and its boundary. • Tensile property of AlSi7Mg ribbon was studied with UTS 1.5 times higher than ingot. • Effects of nanoscale Si particles on hardness and tensile properties were provided. - Abstract: The two directional microstructure and multiple mechanical properties of the AlSi7Mg ribbon produced by melt-spun were investigated by optical microscopy (OM), field emission gun scanning electron microscope (FEGSEM), X-ray diffraction (XRD), microhardness and tensile tests. Both the surface and cross-sectional microstructure of the melt-spun ribbon were characterized in detail to give a clear and integrated description of the microstructure. Two kinds of nanoscale Si particles were observed, i.e., small Si particles ranging from 13 to 50 nm and large Si particles ranging from 50 nm to several hundreds of nanometers with clear size boundary were dispersed both in the interior and boundary of fine α-Al. XRD results revealed supersaturated solution of Si in Al matrix to be 0.62 at.%. The ultimate tensile strength, yield strength, and hardness of the ribbon were 1.53, 1.75 and 1.56 times higher than that of the conventional cast ingot separately. The breaking elongation of the ribbon was 1.73% with intergranular fracture feature. The effects of nanoscale dispersed Si particles on the significant improvement of both hardness and tensile properties of the AlSi7Mg melt-spun ribbon were discussed in detail.

Severe plastic deformation of melt-spun shape memory Ti2NiCu and Ni2MnGa alloys

International Nuclear Information System (INIS)

Pushin, Vladimir G.; Korolev, Alexander V.; Kourov, Nikolai I.; Kuntsevich, Tatiana E.; Valiev, Eduard Z.; Yurchenko, Lyudmila I.; Valiev, Ruslan Z.; Gunderov, Dmitrii V.; Zhu, Yuntian T.

2006-01-01

This paper describes the influence of severe plastic deformation (SPD) on the structure, phase transformations, and physical properties of melt-spun Ti 2 NiCu-based and Ni 2 MnGa-based shape memory intermetallic alloys. It was found that the SPD by high pressure torsion (HPT) at room temperature can be effectively used for the synthesis of bulk nanostructured states in these initially submicro-grained or amorphized alloys obtained by melt-spinning method in the form of a ribbon. The subsequent low-temperature annealing of HPT-processed alloys leads to formation of homogeneous ultrafine nano-grained structure. This is connected with a very high degree and high homogeneity of deformation at SPD in the whole volume of deformed samples. (author)

Magnetic properties of nanocrystallized Fe-Pt-B melt-spun ribbons

International Nuclear Information System (INIS)

Yamamoto, Tokujiro; Omori, Akihiro; Kimura, Hisamichi; Inoue, Akihisa

2007-01-01

L1 0 FePt nanoparticles have been prepared by etching grain boundaries of heat-treated melt-spun Fe-19Pt-25B (at.%) alloy ribbons. It is revealed that an L1 0 FePt nanocrystalline phase is directly formed from the Fe-Pt-B amorphous ribbons by long-time heat treatment at low temperatures in the vicinity of 723 K. With increasing heat treatment time, dimensions of the nanocrystallized FePt grains increase, accompanied by a change from soft ferromagnetic to hard ferromagnetic. The ribbon crystallized at 723 K for 1.8 ks consists of only an FePt L1 0 phase and its coercivity is as low as 0.381 kA/m. However, it increases to 372 kA/m with increasing grain size of precipitated L1 0 phase to about 30 nm by heat treatment for 86.4 ks, while the saturation magnetic flux density remains constant at about 0.4 T. Etching boundaries in heat-treated ribbons has been performed to obtain ferromagnetic L1 0 FePt nanoparticles and several particles were observed by means of transmission electron microscopy

The electrochemical properties of melt-spun Al-Si-Cu alloys

Energy Technology Data Exchange (ETDEWEB)

Zhang Linping; Wang Fei; Liang Pu; Song Xianlei; Hu Qing [MOE Key Laboratory for Non-equilibrium Synthesis and Modulation of Condensed Matter, State Key Laboratory for Mechanical Behavior of Materials, Xi' an Jiaotong University, Xi' an 710049 (China); Sun Zhanbo, E-mail: szb@mail.xjtu.edu.cn [MOE Key Laboratory for Non-equilibrium Synthesis and Modulation of Condensed Matter, State Key Laboratory for Mechanical Behavior of Materials, Xi' an Jiaotong University, Xi' an 710049 (China); Song Xiaoping; Yang Sen; Wang Liqun [MOE Key Laboratory for Non-equilibrium Synthesis and Modulation of Condensed Matter, State Key Laboratory for Mechanical Behavior of Materials, Xi' an Jiaotong University, Xi' an 710049 (China)

2011-10-03

Highlights: {yields} Non-equilibrium Al{sub 75-X}Si{sub 25}Cu{sub X} alloys exhibit high lithiation storages. {yields} The lithiation mechanism is different from melt-spun Al-Si-Mn system. {yields} The structural evolution is mitigated in the non-equilibrium alloys. {yields} Volume variation is alleviated due to the co-existence of Al{sub 2}Cu, {alpha}-Si and {alpha}-Al. - Abstract: Melt spinning was used to prepare Al{sub 75-X}Si{sub 25}Cu{sub X} (X = 1, 4, 7, 10 mol%) alloy anode materials for lithium-ion batteries. A metastable supersaturated solid solution of Si and Cu in fcc-Al, {alpha}-Si and Al{sub 2}Cu co-existed in the alloys. Nano-scaled {alpha}-Al grains, as the matrix, formed in the as-quenched ribbons. The Al{sub 74}Si{sub 25}Cu{sub 1} and Al{sub 71}Si{sub 25}Cu{sub 4} anodes exhibited initial discharge specific capacities of 1539 mAh g{sup -1}, 1324 mAh g{sup -1} and reversible capacities above 472 mAh g{sup -1}, 508 mAh g{sup -1} at the 20th cycle, respectively. The specific capacities reduced as the increase of the Cu content. AlLi intermetallic compound was detected in the lithiated alloys. It is concluded that the lithiation mechanism of the Al-Si-based alloys can be affected by the third component. The structural evolution and volume variation can be mitigated due to the formation of non-equilibrium state and the co-existence of nano-scaled {alpha}-Al, {alpha}-Si, and Al{sub 2}Cu for the present alloys.

Depth-Sensing Microindentation Studies of Melt Spun Al-12wt%Si-0.5wt%Sb Alloys

International Nuclear Information System (INIS)

Uzun, O.

2004-01-01

In this study, the indentation load-penetration depth curves of melt spun ribbons were measured under different peak load levels. The unloading segments of these curves were analyzed using widely adopted Oliver and Pharr method. It was found that both hardness and Youngs modulus exhibit significant peak load dependence. Empirical approaches were then proposed to determine the load independent hardness, H0, and modulus. The load independent hardness (1135.07 and 756.72 MPa) and modulus (13.4 and 7.2 GPa) values were then calculated for wheel and air side of the ribbon, respectively. The results showed that the reduced elastic modulus increases with increasing hardness

Structure and magnetic properties of Heusler alloy Co{sub 2}RuSi melt-spun ribbons

Energy Technology Data Exchange (ETDEWEB)

Xin, Yuepeng; Ma, Yuexing; Hao, Hongyue [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Luo, Hongzhi, E-mail: luo_hongzhi@163.com [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Meng, Fanbin; Liu, Heyan [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Liu, Enke; Wu, Guangheng [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)

2017-08-01

Highlights: • New Heusler alloy Co{sub 2}RuSi has been prepared by melt-spinning successfully. • Magnetic and electronic properties of Co{sub 2}RuSi were investigated. • Ru has a strong site preference for A, C sites in the lattice of Co{sub 2}RuSi. • Site preference of Ru cannot be determined by “number of valence electrons”. - Abstract: Heusler alloy Co{sub 2}RuSi has been synthesized by melt-spinning technology successfully. Co{sub 2}RuSi bulk sample after annealing is composed of an HCP Co-rich phase and a BCC Ru-Si phase, but melt-spinning can suppress the precipitation of the HCP phase and produce a single Co{sub 2}RuSi Heusler phase. In the XRD pattern, it is found that Ru has a strong preference for the (A, C) sites, though it has fewer valence electrons compared with Co. This site preference is different from the case in Heusler alloys containing only 3d elements and is supported further by first-principles calculations. Melt-spun Co{sub 2}RuSi has a M{sub s} of 2.67 μ{sub B}/f.u. at 5 K and a Tc of 491 K. An exothermic peak is observed at 871 K in the DTA curve, corresponding to the decomposition of the Heusler phase. Finally, the site preference and magnetic properties of Co{sub 2}RuSi were discussed based on electronic structure calculation and charge density difference.

Molecular field analysis for melt-spun amorphous Fe sub 1 sub 0 sub 0 sub - sub x Gd sub x alloys (18<=60)

CERN Document Server

Yano, K

2000-01-01

The magnetic properties for the melt-spun amorphous Fe sub 1 sub 0 sub 0 sub - sub x Gd sub x alloys were analyzed using the molecular field theory (MFT). A concentration dependence of three exchange interaction constants was derived over a wide concentration range (18=T sub c sub o sub m sub p. Curvature of the Arrott plot in Gd-rich region was qualitatively simulated.

Exchange correlation length and magnetoresistance in Fe-Cu and Fe-Cu-Ni melt-spun ribbons

International Nuclear Information System (INIS)

El Ghannami, M.; Gomez-Polo, C.; Rivero, G.; Hernando, A.

1994-01-01

The magnetic properties of Fe 30 Cu 70 melt-spun ribbons are reported for the first time. In the as-cast state, the microstructure consists of b.c.c.-Fe grains immersed in a Cu-rich matrix. However, the addition of a small percentage of Ni gives rise to the appearance of new Cu-Fe-Ni phases. Under suitable thermal treatments, the microstructure of both alloys evolves towards a complete phase segregation in b.c.c-Fe and f.c.c.-Cu immiscibles phases. The temperature dependence of the magnetic properties is analysed and related to the microstructural changes produced during the thermal treatments. Remarkable magneto-resistance effects have been observed in both as-cast alloys, with maximum values of the order of 6% at low measuring temperatures. (orig.)

Effects of the ingot phase transition on microstructure and magnetic properties of CeNdFeB melt-spun ribbons

Energy Technology Data Exchange (ETDEWEB)

Wang, Xuchao [Division of Functional Materials Research, Central Iron and Steel Research Institute, Beijing 100081, China (China); College of Sciences, Northeastern University, Shenyang 110819 (China); Zhu, Minggang, E-mail: mgzhu@126.com [Division of Functional Materials Research, Central Iron and Steel Research Institute, Beijing 100081, China (China); Li, Wei; Zheng, Liyun; Guo, Zhaohui; Du, Xiao [Division of Functional Materials Research, Central Iron and Steel Research Institute, Beijing 100081, China (China); Du, An [College of Sciences, Northeastern University, Shenyang 110819 (China)

2015-11-01

The paper studies the phase transition of ingot with the composition (Ce{sub 50}Nd{sub 50}){sub 30}Fe{sub bal}Co{sub 4}Ga{sub 0.2}B{sub 0.92} after the annealing treatment at 1050 °C. The melt-spun ribbons which is prepared by the two treatment status ingots. The phase structure and microstructure morphologies of the ingots and melt-spun ribbons were analysed and observed by XRD and SEM. It was found that the grain size of the ribbons is on the nanometer scale. The EDS results show that there are four different phases in the ingot: (CeNd){sub 2}Fe{sub 14}B, α-Fe, Ce-rich phase and Nd-rich phase. After the annealing treatment, α-Fe, Ce-rich phase, and Nd-rich phase were obviously reduced and the contents of the main phase was significantly increased in the annealed ingot compared with the unanneal treatment ingot. The VSM results show that there is a peak waist in the ribbon which is prepared by the untreated ingot. Because the ingot is uneven, the ribbons may have the secondary phase, the Hcj is 8394 Oe. But the demagnetization curves of the ribbons, which is prepared by the annealed ingot, is relatively smooth and without the soft magnetic phase and the Hcj is 12,528 Oe, which is higher than the unanneal treatment ingot. We can know that the ingot with fine organization is the key factors to preparing high-performance ribbons.

Purification of melt-spun metallurgical grade silicon micro-flakes through a multi-step segregation procedure

Science.gov (United States)

Martinsen, F. A.; Nordstrand, E. F.; Gibson, U. J.

2013-01-01

Melt-spun metallurgical grade (MG) micron dimension silicon flakes have been purified into near solar grade (SG) quality through a multi-step melting and re-solidification procedure. A wet oxidation-applied thermal oxide maintained the sample morphology during annealing while the interiors were melted and re-solidified. The small thickness of the flakes allowed for near elimination of in-plane grain boundaries, with segregation enhanced accumulation of impurities at the object surface and in the few remaining grain boundaries. A subsequent etch in 48% hydrofluoric acid (HF) removed the impure oxide layer, and part of the contamination at the oxide-silicon interface, as shown by electron dispersive spectroscopy (EDS) and backscattered electron imaging (BEI). The sample grains were investigated by electron back-scattered diffraction (EBSD) after varying numbers of oxidation-annealing-etch cycles, and were observed to grow from ˜5 μm to ˜200 μm. The concentration of iron, titanium, copper and aluminium were shown by secondary ion mass spectroscopy (SIMS) and inductively coupled plasma mass spectroscopy (ICPMS) to drop between five and six orders of magnitude. The concentration of boron was observed to drop approximately one order of magnitude. A good correlation was observed between impurity removal rates and segregation models, indicating that the purification effect is mainly caused by segregation. Deviations from these models could be explained by the formation of oxides and hydroxides later removed through etching.

Phase transformations in Zr-29.56 at.% Cu-19.85 at.% Ni melt-spun high-temperature shape memory alloy

International Nuclear Information System (INIS)

Firstov, G.S.; Koval, Yu.N.; Van Humbeeck, J.; Portier, R.; Vermaut, P.; Ochin, P.

2006-01-01

The present paper focuses on the phase transformations during crystallization of the melt-spun Zr-29.56 at.% Cu-19.85 at.% Ni high-temperature shape memory alloy (HTSMA). This alloy exhibits a martensitic transformation in the bulk polycrystalline state at temperatures above crystallization of the metallic glass with the same composition. The crystallization kinetics were investigated by differential scanning calorimetry. The intermediate and final products of crystallization for this HTSMA were studied by means of transmission electron microscopy. The chain of the transformations starting from crystallization and ending at martensitic transformation will be described. Perspectives of the thin film production of Zr-based HTSMA will be discussed

Phase transformations in Zr-29.56 at.% Cu-19.85 at.% Ni melt-spun high-temperature shape memory alloy

Energy Technology Data Exchange (ETDEWEB)

Firstov, G.S. [Institute for Metal Physics, National Academy of Sciences, 36 Vernadsky blvd., UA-03680, Kiev-142 (Ukraine)]. E-mail: gfirst@imp.kiev.ua; Koval, Yu.N. [Institute for Metal Physics, National Academy of Sciences, 36 Vernadsky blvd., UA-03680, Kiev-142 (Ukraine); Van Humbeeck, J. [Department MTM, Catholic University of Leuven, Kasteelpark Arenberg 44, B-3001 Heverlee (Leuven) (Belgium); Portier, R. [Laboratoire de Metallurgie Structurale ENSCP, 11 rue Pierre et Marie Curie, 75231 Paris Cedex 05 (France); Vermaut, P. [Laboratoire de Metallurgie Structurale ENSCP, 11 rue Pierre et Marie Curie, 75231 Paris Cedex 05 (France); Ochin, P. [Centre d' Etudes de Chimie Metallurgique-CNRS UPR2801, 15 rue Georges Urbain, 94407 Vitry-sur-Seine (France)

2006-11-25

The present paper focuses on the phase transformations during crystallization of the melt-spun Zr-29.56 at.% Cu-19.85 at.% Ni high-temperature shape memory alloy (HTSMA). This alloy exhibits a martensitic transformation in the bulk polycrystalline state at temperatures above crystallization of the metallic glass with the same composition. The crystallization kinetics were investigated by differential scanning calorimetry. The intermediate and final products of crystallization for this HTSMA were studied by means of transmission electron microscopy. The chain of the transformations starting from crystallization and ending at martensitic transformation will be described. Perspectives of the thin film production of Zr-based HTSMA will be discussed.

Effect of TiC additions to the microstructure and magnetic properties of Nd9.5Fe84.5B6 melt-spun ribbons

International Nuclear Information System (INIS)

Kramer, M.J.; Li, C.P.; Dennis, K.W.; McCallum, R.W.; Sellers, C.H.; Branagan, D.J.; Lewis, L.H.; Wang, J.Y.

1998-01-01

Rapidly solidified samples of Nd 9.5 Fe 84.5 B 6 with and without 3 at.% TiC were prepared by melt spinning and melt extraction and then annealed in vacuum (3x10 -6 Torr) at temperatures from 600 to 750 degree C. For alloys melt spun under similar conditions, the overquenched state was achieved at wheel speeds >10 m/s for the TiC added alloy while >20 m/s was necessary without TiC. The overquenched samples contained a smaller fraction of α-Fe in smaller grains than the undercooled samples where Fe dendrites formed near the free surface during solidification. These Fe dendrites were not removed by annealing. In addition, large orientated 2-14-1 grains nucleated on the Fe dendrites. This combination is detrimental to the magnetic properties. The addition of TiC results in improved control of the microstructure over a larger fraction of the ribbon volume enhancing the magnetic properties. copyright 1998 American Institute of Physics

Nanocrystallinity and magnetic property enhancement in melt-spun iron-rare earth-base hard magnetic alloys

International Nuclear Information System (INIS)

Davies, H.A.; Manaf, A.; Zhang, P.Z.

1993-01-01

Refinement of the grain size below ∼35 nm mean diameter in melt-spun FeNdB-base alloys leads to enhancement of remanent polarization, J r , above the level predicted by the Stoner-Wohlfarth theory for an aggregate of independent, randomly oriented, and uniaxial magnetic particles. This article summarizes the results of the recent systematic research on this phenomenon, including the influence of alloy composition and processing conditions on the crystallite size, degree of enhancement of J r , and maximum energy product (BH) max . It has been shown that the effect can also occur in ternary FeNdB alloys, without the addition of silicon or aluminum, which was originally thought necessary, providing the nanocrystallites are not magnetically decoupled by a paramagnetic second phase. Values of (BH) max above 160 kJ. m -3 have been achieved. The relationship between grain size, J r , intrinsic coercivity, J H c , and (BH) max are discussed in terms of magnetic exchange coupling, anisotropy, and other parameters. Recent extension of this work to the enhancement of properties in Fe-Mischmental-Boron-base alloys and to bonded magnets with a nanocrystalline structure is also described

Analysis of grain growth process in melt spun Fe-B alloys under the initial saturated grain boundary segregation condition

International Nuclear Information System (INIS)

Chen, Z.; Liu, F.; Yang, X.Q.; Fan, Y.; Shen, C.J.

2012-01-01

Highlights: → We compared pure kinetic, pure thermodynamic and extended thermo-kinetic models. → An initial saturated GB segregation condition of nanoscale Fe-B alloys was determined. → The controlled-mechanism was proposed using two characteristic times (t 1 and t 2 ). - Abstract: A grain growth process in the melt spun low-solid-solubility Fe-B alloys was analyzed under the initial saturated grain boundary (GB) segregation condition. Applying melt spinning technique, single-phase supersaturated nanograins were prepared. Grain growth behavior of the single-phase supersaturated nanograins was investigated by performing isothermal annealing at 700 deg. C. Combined with the effect of GB segregation on the initial GB excess amount, the thermo-kinetic model [Chen et al., Acta Mater. 57 (2009) 1466] was extended to describe the initial GB segregation condition of nanoscale Fe-B alloys. In comparison of pure kinetic model, pure thermodynamic model and the extended thermo-kinetic model, an initial saturated GB segregation condition was determined. The controlled-mechanism of grain growth under initial saturated GB segregation condition was proposed using two characteristic annealing times (t 1 and t 2 ), which included a mainly kinetic-controlled process (t ≤ t 1 ), a transition from kinetic-mechanism to thermodynamic-mechanism (t 1 2 ) and pure thermodynamic-controlled process (t ≥ t 2 ).

Controlling the crystallization and magnetic properties of melt-spun Pr2Fe14B/α-Fe nanocomposites by Joule heating

Science.gov (United States)

Jin, Z. Q.; Cui, B. Z.; Liu, J. P.; Ding, Y.; Wang, Z. L.; Thadhani, N. N.

2004-05-01

Pr2Fe14B/α-Fe based nanocomposites have been prepared through crystallization of melt-spun amorphous Pr7Tb1Fe85Nb0.5Zr0.5B6 ribbons by means of ac Joule heating while simultaneously monitoring room-temperature electrical resistance R. The R value shows a strong variation with respect to applied current I, and is closely related to the amorphous-to-nanocrystalline phase transformation. The curve of R versus I allows one to control the crystallization behavior during Joule heating and to identify the heat-treatment conditions for optimum magnetic properties. A coercivity of 550 kA/m and a maximum energy product of 128 kJ/m3 have been obtained upon heating the amorphous ribbons at a current of 2.0 A. These properties are around 30% higher than the values of samples prepared by conventionally (furnace) annealed amorphous ribbons.

Effect of Zr Purity and Oxygen Content on the Structure and Mechanical Properties of Melt-Spun and Suction-Cast Cu46Zr42Al7Y5 Alloy

Directory of Open Access Journals (Sweden)

Kozieł T.

2016-06-01

Full Text Available The effect of oxygen content in zirconium on the structure and mechanical properties of the Cu46Zr42Al7Y5 alloy, in the form of melt-spun ribbons and suction-cast rods, was investigated. Two types of Zr, rod and crystal bar of different nominal purities and oxygen contents, were used to synthesize the alloy by arc melting. Rapidly solidified ribbons were produced by melt spinning and their amorphous structures were confirmed by X-ray diffractometry (XRD and differential scanning calorimetry (DSC. Bulk samples in the form of rods were cast using a special water-cooled suction casting unit attached to the arc melting system. XRD and DSC studies proved the amorphous structure of the bulk alloy synthesized from low-oxygen Zr and partial crystallization of the same alloy for high-oxygen Zr. In both bulk samples, uniformly distributed crystalline particles were identified as yttrium oxides. Higher mean compressive strength of amorphous alloy was observed. The hardness of amorphous phase was close to 500 HV1 in both bulk alloys, while the hardness of crystalline dendritic areas, observed in the alloy synthesized from high oxygen Zr, was lower by about 50 HV1.

Morphology and the structure of quasicrystal phase in as-cast and melt-spun Mg-Zn-Y-Zr alloys

International Nuclear Information System (INIS)

Tang, Y.L.; Zhao, D.S.; Shen, N.F.

1993-01-01

During recent years, many researchers have investigated the experimental and theoretical aspects of quasicrystal materials. In some Mg alloys (Mg 32 Al 17 Zn 32 , Mg 32 (Al,Zn) 49 , Mg 32 (Al,Zn,Cu) 49 , Mg 4 CuAl 6 and Ga 16 Mg 32 Zn 52 ), icosahedral quasicrystals (IQC) have been found. However, most of the quasicrystals in these alloys were formed under a rapid solidification condition. In the recent study on Mg-Zn-(Zr,Y) as-cast alloys, the authors identified a new Mg-rich and a Zn-rich IQC by X-ray diffraction (XRD) and electron microscopy (EM). The discovery of Mg-Zn-Y IQC is of interest because it formed in an as-cast ingot and did not contain the element Al, which is the major constituent of nearly all IQC forming alloys reported. Also, analyses on IQC in as-cast and RS Mg alloys with the composition have not previously been carried out. In this paper, TEM and XRD investigations were completed on IQC formed in a Mg-Zn-Y-Zr cast ingot and melt-spun ribbons for microstructure comparison

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

Science.gov (United States)

Pinkerton, Frederick E.; Balogh, Michael P.; Ellison, Nicole; Foto, Aldo; Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P.

2016-11-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity Hci of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H2 gas. Expansion of the NdFeB crystal lattice in both ATF and H2 identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets.

Composition-dependent magnetic properties of melt-spun La or/and Ce substituted nanocomposite NdFeB alloys

Energy Technology Data Exchange (ETDEWEB)

Hussain, M.; Zhao, L.Z.; Zhang, C.; Jiao, D.L.; Zhong, X.C.; Liu, Z.W.

2016-02-15

Aiming at high-performance low-cost NdFeB magnets, the magnetic properties and microstructure for melt spun nanocrystalline (Nd{sub 1−x}M{sub x}){sub 10}Fe{sub 84}B{sub 6} (M=La, Ce, or La{sub 0.5}Ce{sub 0.5}; x=0–0.7) alloys were investigated. Relatively, LaCe-substituted alloys show high values of the remanent magnetization M{sub r}, the maximum energy product (BH){sub max} and the coercivity H{sub c}, up to 114 emu/g (1.07 T), 147 kJ/m{sup 3} and 471 kA/m, respectively, at x=0.1. The unusual increase in coercivity for the alloys with 10% La or 10% La{sub 0.5}Ce{sub 0.5} substitution is possibly attributed to the phase segregation in alloys with certain La or LaCe contents. The reduced Curie temperature and spin-reorientation temperature were obtained for La, Ce or LaCe substituted alloys. Transmission electron microscope analysis has revealed that a fine and uniform distributed grain structure leads to remanence enhancement for La{sub 0.5}Ce{sub 0.5} substituted alloys. The present results indicate that partially substituting Nd by La or/and Ce cannot only effectively reduce the cost of nanocrystalline NdFeB based magnetic powders but also can maintain a relatively good combination of magnetic properties.

The Influence of Solid-State Drawing on Mechanical Properties and Hydrolytic Degradation of Melt-Spun Poly(Lactic Acid (PLA Tapes

Directory of Open Access Journals (Sweden)

Fang Mai

2015-12-01

Full Text Available The influence of solid-state drawing on the morphology of melt-spun poly(l-lactic acid (PLLA tapes, and the accompanying changes in mechanical and degradation behaviour have been studied. Mechanical properties are found to be strongly dependent on both applied draw ratio and drawing temperature. Moduli of these highly oriented tapes are significantly increased compared to as-extruded tapes at both ambient and elevated temperatures. Interestingly, drawing leads to a significant increase in elongation to break (~3 times and toughness (~13 times compared to as-extruded tapes. Structural and morphological characterization indicates strain-induced crystallization as well as an increase in orientation of the crystalline phase at small strains. Upon further stretching, an “overdrawing” regime is observed, with decreased crystalline orientation due to the breakage of existing crystals. For fixed draw ratios, a significant increase in Young’s modulus and tensile strength is observed with increasing drawing temperature, due to a higher crystallinity and orientation obtained for tapes drawn at higher temperatures. FT-IR results indicate no crystal transformation after drawing, with the α-form being observed in all tapes. Hydrolytic degradability of PLLA was significantly reduced by solid-state drawing.

Electrochemical characterization of melt spun AB{sub 5} alloys for metal hydride batteries

Energy Technology Data Exchange (ETDEWEB)

Brateng, Randi

2003-05-01

(NiSn){sub 5}, did not seem to be related to the structural parameters, because the unit cell volume was almost independent of the cooling rate. After heat treatment of both melt spun Mm(NiCoMnA1){sub 5.15} and La(NiSn){sub 5}, the unit cell volume and the electrochemical properties seemed to be almost independent of the cooling rate, within the experimental error. La(NiSn){sub 5} showed an effect of storage of the materials. For Mm(NiCoMnA1){sub 5.15} this effect was weaker. The unit cell volume and the electrochemical parameters after aging were less affected when the cooling rate was varied.

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

International Nuclear Information System (INIS)

Pinkerton, Frederick E.; Balogh, Michael P.; Ellison, Nicole; Foto, Aldo; Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P.

2016-01-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity H ci of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H 2 gas. Expansion of the NdFeB crystal lattice in both ATF and H 2 identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets. - Highlights: • Injection molded NdFeB magnets age rapidly in automatic transmission fluid (ATF). • Coercivity loss is not due to direct chemical reaction between ATF and the powder. • Chemical reaction with the binder does not play a major role in aging. • Hydrogen dissociates from ATF and diffuses into Nd 2 Fe 14 B, reducing coercivity.

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

Energy Technology Data Exchange (ETDEWEB)

Pinkerton, Frederick E., E-mail: frederick.e.pinkerton@gm.com [Chemical and Materials Systems Laboratory, General Motors Research and Development Center, Warren, MI 48092 (United States); Balogh, Michael P.; Ellison, Nicole [Chemical and Materials Systems Laboratory, General Motors Research and Development Center, Warren, MI 48092 (United States); Foto, Aldo [Element Materials Technology Wixom, Inc (United States); Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P. [Powertrain Materials/Fluids/AMPPD Engineering and Labs, GFL VE/PT Materials Engineering, General Motors LLC, Pontiac, MI 48340 (United States)

2016-11-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity H{sub ci} of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H{sub 2} gas. Expansion of the NdFeB crystal lattice in both ATF and H{sub 2} identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets. - Highlights: • Injection molded NdFeB magnets age rapidly in automatic transmission fluid (ATF). • Coercivity loss is not due to direct chemical reaction between ATF and the powder. • Chemical reaction with the binder does not play a major role in aging. • Hydrogen dissociates from ATF and diffuses into Nd{sub 2}Fe{sub 14}B, reducing coercivity.

Properties of alginate fiber spun-dyed with fluorescent pigment dispersion.

Science.gov (United States)

Wang, Ping; Tawiah, Benjamin; Tian, Anli; Wang, Chunxia; Zhang, Liping; Fu, Shaohai

2015-03-15

Spun-dyed alginate fiber was prepared by the spun-dyeing method with the mixture of fluorescent pigment dispersion and sodium alginate fiber spinning solution, and its properties were characterized by SEM, TGA, DSC, and XRD. The results indicate that fluorescent pigment dispersion prepared with esterified poly (styrene-alt maleic acid) had excellent compatibility with sodium alginate fiber spinning solution, and small amount of fluorescent pigment could reduce the viscosity of spun-dyed spinning solutions. SEM photo of spun-dyed alginate fiber indicated that fewer pigment particles deposited on its surface. TGA, DSC, and XRD results suggested that thermal properties and crystal phase of spun-dyed alginate fibers had slight changes compared to the original alginate fibers. The fluorescence intensity of spun-dyed alginate fiber reached its maximum when the content of fluorescent pigment was 4%. The spun-dyed alginate fiber showed excellent rubbing and washing fastness. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hot deformed anisotropic nanocrystalline NdFeB based magnets prepared from spark plasma sintered melt spun powders

Energy Technology Data Exchange (ETDEWEB)

Hou, Y.H.; Huang, Y.L. [School of Materials Science and Engineering, Nanchang Hangkong University, Nanchang 330063 (China); School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Liu, Z.W., E-mail: zwliu@scut.edu.cn [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Zeng, D.C. [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Ma, S.C.; Zhong, Z.C. [School of Materials Science and Engineering, Nanchang Hangkong University, Nanchang 330063 (China)

2013-09-01

Highlights: • Microstructure evolution and its influence on the magnetic properties were investigated. • The increase of stray field and weakening of domain-wall pinning effects were the main reasons of the decrease of the coercivity with increasing the compression ratio. • The influences of non-uniform plastic deformation on the microstructure and magnetic properties were investigated. • Magnetic properties and temperature coefficient of coercivity are indeed very promising without heavy rare earth elements. -- Abstract: Anisotropic magnets were prepared by spark plasma sintering (SPS) followed by hot deformation (HD) using melt-spun powders as the starting material. Good magnetic properties with the remanence J{sub r} > 1.32 T and maximum of energy product (BH){sub max} > 303 kJ/m{sup 3} have been obtained. The microstructure evolution during HD and its influence on the magnetic properties were investigated. The fine grain zone and coarse grain zone formed in the SPS showed different deformation behaviors. The microstructure also had an important effect on the temperature coefficients of coercivity. A strong domain-wall pinning model was valid to interpret the coercivity mechanism of the HDed magnets. The increase of stray field and weakening of domain-wall pinning effects were the main reasons of the decrease of the coercivity with increasing the compression ratio. The influences of non-uniform plastic deformation on the microstructure and magnetic properties were investigated. The polarization characteristics of HDed magnets were demonstrated. It was found out that the HDed magnets had better corrosion resistance than the counterpart sintered magnet.

Characterization of the kinetic arrest of martensitic transformation in Ni45Co5Mn36.8In13.2 melt-spun ribbons

Science.gov (United States)

Lino-Zapata, F. M.; Yan, H. L.; Ríos-Jara, D.; Sánchez Llamazares, J. L.; Zhang, Y. D.; Zhao, X.; Zuo, L.

2018-01-01

The kinetic arrest (KA) of martensitic transformation (MT) observed in Ni45Co5Mn36.8In13.2 melt-spun ribbons has been studied. These alloy ribbons show an ordered columnar-like grain microstructure with the longer grain axis growing perpendicular to ribbon plane and transform martensitically from a single austenitic (AST) parent phase with the L21-type crystal structure to a monoclinic incommensurate 6 M modulated martensite (MST). Results show that the volume fraction of austenite frozen into the martensitic matrix is proportional to the applied magnetic field. A fully arrest of the structural transition is found for a magnetic field of 7 T. The metastable character of the non-equilibrium field-cooled glassy state was characterized by introducing thermal and magnetic field fluctuations or measuring the relaxation of magnetization. The relaxation of magnetization from a field-cooled kinetically arrested state at 5 and 7 T follows the Kohlrausch-Williams-Watts (KWW) stretched exponential function with a β exponent around 0.95 indicating the weak metastable nature of the system under the strong magnetic fields. The relationship between the occurrence of exchange bias and the frozen fraction of AST into the MST matrix was studied.

Enhanced Hydrogen Storage Kinetics of Nanocrystalline and Amorphous Mg₂Ni-type Alloy by Melt Spinning.

Science.gov (United States)

Zhang, Yang-Huan; Li, Bao-Wei; Ren, Hui-Ping; Li, Xia; Qi, Yan; Zhao, Dong-Liang

2011-01-18

Mg₂Ni-type Mg₂Ni 1-x Co x (x = 0, 0.1, 0.2, 0.3, 0.4) alloys were fabricated by melt spinning technique. The structures of the as-spun alloys were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The hydrogen absorption and desorption kinetics of the alloys were measured by an automatically controlled Sieverts apparatus. The electrochemical hydrogen storage kinetics of the as-spun alloys was tested by an automatic galvanostatic system. The results show that the as-spun (x = 0.1) alloy exhibits a typical nanocrystalline structure, while the as-spun (x = 0.4) alloy displays a nanocrystalline and amorphous structure, confirming that the substitution of Co for Ni notably intensifies the glass forming ability of the Mg₂Ni-type alloy. The melt spinning treatment notably improves the hydriding and dehydriding kinetics as well as the high rate discharge ability (HRD) of the alloys. With an increase in the spinning rate from 0 (as-cast is defined as spinning rate of 0 m/s) to 30 m/s, the hydrogen absorption saturation ratio () of the (x = 0.4) alloy increases from 77.1 to 93.5%, the hydrogen desorption ratio () from 54.5 to 70.2%, the hydrogen diffusion coefficient (D) from 0.75 × 10 - 11 to 3.88 × 10 - 11 cm²/s and the limiting current density I L from 150.9 to 887.4 mA/g.

Magnetic and microstructural investigation of high-coercivity net-shape Nd-Fe-B-type magnets produced from spark-plasma-sintered melt-spun ribbons blended with DyF3

Science.gov (United States)

Žagar, Kristina; Kocjan, Andraž; Kobe, Spomenka

2016-04-01

Nanostructured Nd-Fe-B-type materials produced by melt-spinning (MS) are used in a variety of applications in the electronics, automotive, and sensor industries. The very rapid MS process leads to flake-like powders with metastable, nanoscale, Nd2Fe14B grains. These powders are then formed into net-shaped, isotropic, polymer-bonded magnets, or they are hot formed into fully dense, metallic magnets that are isotropic and anisotropic. These fully dense magnets are usually produced with a conventional hot press without the inclusion of additives prior to the hot pressing. As a result, their properties, particularly the coercivity (Hci), are insufficient at automotive-relevant temperatures of 100-150 °C since the material Hci has a large temperature coefficient. In this study, we instead add a thin layer of DyF3 to the melt-spun ribbons prior to their hot consolidation in order to enhance the coercivity through a diffusion-based, partial substitution of the Nd by Dy. This is accomplished by applying extremely rapid, spark-plasma sintering to minimize any growth of the nanoscale Nd2Fe14B grains during consolidation. The result is a very high-coercivity magnet with drastically reduced amounts of heavy rare earths that is suitable for high-temperature applications. This work clearly demonstrates how rapidly formed, metastable states can provide us with properties that are unobtainable with conventional techniques.

Mechanical response of melt-spun amorphous filaments

International Nuclear Information System (INIS)

Leal, A A; Reifler, F A; Hufenus, R; Mohanty, G; Michler, J

2014-01-01

High-speed melt spinning of a cyclo-olefin polymer (COP) and a copolyamide (CoPA) have been performed. Differential scanning calorimetry curves of the resulting monofilaments show that they remain in an amorphous state even after hot drawing. Wide angle x-ray diffraction patterns of undrawn and drawn COP filaments show that although the material remains in an amorphous state, a degree of orientation is induced in the polymer after drawing. The amorphous filaments show an enhanced bending recovery with respect to different semi-crystalline monofilaments commercially available. However, single fiber axial compressive testing indicates that the amorphous filaments exhibit a compressive modulus value which is 50% lower than what is observed for a reference semi-crystalline PET filament. Analysis of the compressive strains applied by the bending recovery test indicates that while the maximum applied strains remain well within the region of elastic deformation of the amorphous materials, the threshold between elastic and plastic deformation is reached for the semi-crystalline materials. (paper)

Hydrostatic extrusion of Cu-Ag melt spun ribbon

Science.gov (United States)

Hill, Mary Ann; Bingert, John F.; Bingert, Sherri A.; Thoma, Dan J.

1998-01-01

The present invention provides a method of producing high-strength and high-conductance copper and silver materials comprising the steps of combining a predetermined ratio of the copper with the silver to produce a composite material, and melt spinning the composite material to produce a ribbon of copper and silver. The ribbon of copper and silver is heated in a hydrogen atmosphere, and thereafter die pressed into a slug. The slug then is placed into a high-purity copper vessel and the vessel is sealed with an electron beam. The vessel and slug then are extruded into wire form using a cold hydrostatic extrusion process.

Environmentally friendly and highly productive bi-component melt spinning of thermoregulated smart polymer fibres with high latent heat capacity

Directory of Open Access Journals (Sweden)

Ch. Cherif

2018-03-01

Full Text Available A stable and reproducible bi-component melt spinning process on an industrial scale incorporating Phase Change Material (PCM into textile fibres has been successfully developed and carried out using a melt spinning machine. The key factor for a successful bi-component melt spinning process is that a deep insight into the thermal and rheological behaviour of PCM using Difference Scanning Calorimetry (DSC, Thermogravimetric Analysis (TGA, and an oscillatory rheological investigation. PCM is very sensitive to the temperature and residence time of the melt spinning process. It is found that the optimal process temperature of PCM is 210 °C. The textile-physical properties and the morphology of the melt spun and further drawn bi-component core and sheath fibres (bico fibres were investigated and interpreted. The heat capacities of PCM incorporated in bico fibres were also determined by means of DSC. The melt spun bico fibres integrating PCM provide a high latent heat of up to 22 J/g, which is three times higher than that of state-of-the-art fibres, which were also obtained using the melt spinning process. Therefore, they have the potential to be used as smart polymer fibres for textile and other technical applications.

Characterisation of the aqueous corrosion process in NdFeB melt spun ribbon and MQI bonded magnets

Science.gov (United States)

McCain, Stephen

A major factor limiting the use and longevity of rare earth based magnetic materials is their susceptibility to aqueous corrosion and associated detrimental effects upon the magnetic properties of the material. This process was investigated through a combination of exposure to simulated environmental conditions and hydrogen absorption/desorption studies (HADS) in conjunction with magnetic characterisation. This study utilises NdFeB MQP-B melt-spun ribbon manufactured by Magnequench, in the form of MQI bonded magnets and also in its unbonded state as MQ powder. Specifically, it was concerned with how effective a variety of bonding media (epoxy resin,PTFE, zinc) and surface coatings (PTFE, Qsil, zinc LPPS, Dex-Cool) were at limiting the impact of aqueous corrosion in MQI bonded magnets. To characterise the effect of hydrogen absorption upon the magnetic properties of the MQP-B, hydrogen uptake was induced followed by a series of outgassing heat treatments with subsequent magnetic characterisation accompanied by HADS techniques performed after each outgas. This allowed comparisons to be made between the effects of aqueous corrosion process and hydrogen absorption upon the magnetic properties of the alloy.. This study has clearly demonstrated the link between the abundance of environmental moisture and rate of Hci losses in MQI bonded magnets. In addition to this the key mechanism responsible for the degradation of magnetic properties has been identified. These losses have been attributed to the absorption of hydrogen generated by the dissociation of water in the presence of NdFeB during the aqueous corrosion process. It has been shown that the use of a bonding media that is impermeable to water can limit the effects of aqueous corrosion by limiting water access to the Magnequench particles (MQP) and also the positive effects of the use of suitable surface coatings has been shown to be effective for the same reason..

Heterogeneous nucleation of entrained eutectic Si in high purity melt spun Al-Si alloys investigated by entrained droplet technique and DSC

International Nuclear Information System (INIS)

Li, J H; Schumacher, P; Albu, M; Hofer, F; Ludwig, T H; Arnberg, L

2016-01-01

Entrained droplet technique and DSC analyses were employed to investigate the influence of trace elements of Sr, Eu and P on the heterogeneous nucleation of entrained eutectic Si in high purity melt spun Al-5wt.% Si alloys. Sr and Eu addition was found to exert negative effects on the nucleation process, while an increased undercooling was observed. This can be attributed to the formation of phosphide compounds having a lower free energy and hence may preferentially form compared to AlP. Only a trace P addition was found to have a profound effect on the nucleation process. The nucleation kinetics is discussed on the basis of the classical nucleation theory and the free growth model, respectively. The estimated AlP patch size was found to be sufficient for the free growth of Si to occur within the droplets, which strongly indicates that the nucleation of Si on an AlP patch or AlP particle is a limiting step for free growth. The maximum nucleation site density within one droplet is directly related to the size distribution of AlP particles or AlP patches for Si nucleation, but is independent of the cooling rates. Although the nucleation conditions were optimized in entrained droplet experiments, the observed mechanisms are also valid at moderate cooling conditions, such as in shape casting. (paper)

Electro-spun PLA-PEG-yarns for tissue engineering applications

NARCIS (Netherlands)

Kruse, Magnus; Greuel, Marc; Kreimendahl, Franziska; Schneiders, Thomas; Bauer, Benedict; Gries, Thomas; Jockenhoevel, Stefan

2018-01-01

Electro-spinning is widely used in tissue-engineered applications mostly in form of non-woven structures. The development of e-spun yarn opens the door for textile fabrics which combine the micro to nanoscale dimension of electro-spun filaments with three-dimensional (3D) drapable textile fabrics.

Enhanced Hydrogen Storage Kinetics of Nanocrystalline and Amorphous Mg2Ni-type Alloy by Melt Spinning

Directory of Open Access Journals (Sweden)

Hui-Ping Ren

2011-01-01

Full Text Available Mg2Ni-type Mg2Ni1−xCox (x = 0, 0.1, 0.2, 0.3, 0.4 alloys were fabricated by melt spinning technique. The structures of the as-spun alloys were characterized by X-ray diffraction (XRD and transmission electron microscopy (TEM. The hydrogen absorption and desorption kinetics of the alloys were measured by an automatically controlled Sieverts apparatus. The electrochemical hydrogen storage kinetics of the as-spun alloys was tested by an automatic galvanostatic system. The results show that the as-spun (x = 0.1 alloy exhibits a typical nanocrystalline structure, while the as-spun (x = 0.4 alloy displays a nanocrystalline and amorphous structure, confirming that the substitution of Co for Ni notably intensifies the glass forming ability of the Mg2Ni-type alloy. The melt spinning treatment notably improves the hydriding and dehydriding kinetics as well as the high rate discharge ability (HRD of the alloys. With an increase in the spinning rate from 0 (as-cast is defined as spinning rate of 0 m/s to 30 m/s, the hydrogen absorption saturation ratio ( of the (x = 0.4 alloy increases from 77.1 to 93.5%, the hydrogen desorption ratio ( from 54.5 to 70.2%, the hydrogen diffusion coefficient (D from 0.75 × 10−11 to 3.88 × 10−11 cm2/s and the limiting current density IL from 150.9 to 887.4 mA/g.

Influence of the fabrication conditions on the high frequency magnetic response of melt spun Fe73.5Si13.5B9Nb3Cu1

International Nuclear Information System (INIS)

Pascual, L.; El Ghannami, M.; Vazquez, M.; Gomez-Polo, C.; Univ. Publica de Navarra, Pamplona

1998-01-01

The aim of this work is to analyze the influence of the fabrication conditions on the magnetic properties of Fe 73.5 Si 13.5 B 9 Nb 3 Cu 1 melt-spun nanocrystalline ribbons. Different initial structures, amorphous and partially crystalline, have been obtained during the rapid solidification procedure. The structural characterization shows that a decrease in the quenching rate through a reduction in the tangential wheel velocity, gives rise to a partially crystalline state, characterized by the appearance of a textured α-FeSi nanocrystalline phase. The occurrence of the crystalline fraction in the initial as-cast state gives rise to a magnetic hardening with respect to the amorphous sample casted at higher quenching rate. However, the evolution of coercivity under thermal treatments is roughly independent of the initial structure. Moreover, a detailed analysis of the ac susceptibility as a function of annealing temperature shows that the ribbon obtained at lower quenching rate presents higher susceptibility values in the optimum magnetic state (T a = 550 C. 1 h) in a wide range of driving frequency (up to 100 kHz). (orig.)

Carbon nanotube fiber spun from wetted ribbon

Science.gov (United States)

Zhu, Yuntian T; Arendt, Paul; Zhang, Xiefei; Li, Qingwen; Fu, Lei; Zheng, Lianxi

2014-04-29

A fiber of carbon nanotubes was prepared by a wet-spinning method involving drawing carbon nanotubes away from a substantially aligned, supported array of carbon nanotubes to form a ribbon, wetting the ribbon with a liquid, and spinning a fiber from the wetted ribbon. The liquid can be a polymer solution and after forming the fiber, the polymer can be cured. The resulting fiber has a higher tensile strength and higher conductivity compared to dry-spun fibers and to wet-spun fibers prepared by other methods.

Melt-spun polylactic acid fibers: effect of cellulose nanowhiskers on processing and properties

CSIR Research Space (South Africa)

John, MJ

2012-04-01

Full Text Available Bio-based continuous fibers were processed from polylactic acid (PLA) and cellulose nanowhiskers (CNWs) by melt spinning. Melt compounding of master batches of PLA with 10 wt % CNWs and pure PLA was carried out using a twin-screw extruder in which...

Impact of beryllium additions on thermal and mechanical properties of conventionally solidified and melt-spun Al–4.5 wt.%Mn–x wt.%Be (x = 0, 1, 3, 5) alloys

International Nuclear Information System (INIS)

Öz, Turan; Karaköse, Ercan; Keskin, Mustafa

2013-01-01

Highlights: • Thermal and mechanical properties of Al–Mn–Be alloys were investigated. • IQC Al–Mn–Be alloys were synthesized by the CS and MS techniques. • The volume fraction of IQC increases continuously with Be content. • The melting points of the QC i-phase were determined between 652 °C and 675 °C. • The maximum H V and σ values were found to be 124 kg/mm 2 and 458 MPa with the addition of 5% Be. - Abstract: The influence of beryllium (Be) addition on the quasicrystal-forming ability, thermal and mechanical properties of Al–4.5 wt.%Mn–x wt.%Be (x = 0, 1, 3, 5) alloys was investigated in this study. Quasicrystalline Al–Mn–Be alloys were synthesized by the conventionally casting and melt spinning techniques. The microstructures of the samples were characterized by scanning electron microscopy (SEM) and the phase composition was identified by X-ray diffractometry (XRD). The phase transition during the solidification process was studied by differential scanning calorimetry (DSC) and differential thermal analysis (DTA) under an Ar atmosphere. The mechanical properties of the conventionally solidified (CS) and melt-spun (MS) samples were measured by a Vickers micro-hardness indenter and tensile-strength tests. The Al–4.5 wt.%Mn alloy has a hexagonal structure and minor dendritic icosahedral quasicrystalline phase (IQC) precipitates surrounded by an α-Al matrix. Addition of Be into the Al–4.5 wt.%Mn alloy generates intermetallic Be 4 AlMn and IQC phases with the extinction of the hexagonal phase, and the fraction of IQC increases continuously with the increase in Be content. A considerable improvement in microhardness and tensile strength values was observed due to the addition of Be in different percentages into the composition

Electro-spun PLA-PEG-yarns for tissue engineering applications.

Science.gov (United States)

Kruse, Magnus; Greuel, Marc; Kreimendahl, Franziska; Schneiders, Thomas; Bauer, Benedict; Gries, Thomas; Jockenhoevel, Stefan

2018-06-27

Electro-spinning is widely used in tissue-engineered applications mostly in form of non-woven structures. The development of e-spun yarn opens the door for textile fabrics which combine the micro to nanoscale dimension of electro-spun filaments with three-dimensional (3D) drapable textile fabrics. Therefore, the aim of the study was the implementation of a process for electro-spun yarns. Polylactic acid (PLA) and polyethylene glycol (PEG) were spun from chloroform solutions with varying PLA/PEG ratios (100:0, 90:10, 75:25 and 50:50). The yarn samples produced were analyzed regarding their morphology, tensile strength, water uptake and cytocompatibility. It was found that the yarn diameter decreased when the funnel collector rotation was increasd, however, the fiber diameter was not influenced. The tensile strength was also found to be dependent on the PEG content. While samples composed of 100% PLA showed a tensile strength of 2.5±0.7 cN/tex, the tensile strength increased with a decreasing PLA content (PLA 75%/PEG 25%) to 6.2±0.5 cN/tex. The variation of the PEG content also influenced the viscosity of the spinning solutions. The investigation of the cytocompatibility with endothelial cells was conducted for PLA/PEG 90:10 and 75:25 and indicated that the samples are cytocompatible.

Precipitation strengthened high strength, high conductivity Cu-Cr-Nb alloys produced by chill block melt spinning. Final Report Ph.D. Thesis

Science.gov (United States)

Ellis, David L.; Michal, Gary M.

1989-01-01

A series of Cu-based alloys containing 2 to 10 a/o Cr and 1 to 5 a/o Nb were produced by chill block melt spinning (CBMS). The melt spun ribbons were consolidated and hot rolled to sheet to produce a supersaturated Cu-Cr-Nb solid solution from which the high melting point intermetallic compound Cr2Nb could be precipitated to strengthen the Cu matrix. The results show that the materials possess electrical conductivities in excess of 90 percent that of pure Cu at 200 C and above. The strengths of the Cu-Cr-Nb alloys were much greater than Cu, Cu-0.6 Cr, NARloy-A, and NARloy-Z in the as-melt spun condition. The strengths of the consolidated materials were less than Cu-Cr and Cu-Cr-Zr below 500 C and 600 C respectively, but were significantly better above these temperatures. The strengths of the consolidated materials were greater than NARloy-Z, at all temperatures. The GLIDCOP possessed similar strength levels up to 750 C when the strength of the Cu-Cr-Nb alloys begins to degrade. The long term stability of the Cu-Cr-Nb alloys was measured by the microhardness of aged samples and the growth of precipitates. The microhardness measurements indicate that the alloys overage rapidly, but do not suffer much loss in strength between 10 and 100 hours which confirms the results of the electrical resistivity measurements taken during the aging of the alloys at 500 C. The loss in strength from peak strength levels is significant, but the strength remains exceptionally good. Transmission electron microscopy (TEM) of the as-melt spun samples revealed that Cr2Nb precipitates formed in the liquid Cu during the chill block melt spinning, indicating a very strong driving force for the formation of the precipitates. The TEM of the aged and consolidated materials indicates that the precipitates coarsen considerably, but remain in the submicron range.

Propagation of polarised light in bent hi-bi spun fibres

Energy Technology Data Exchange (ETDEWEB)

Przhiyalkovsky, Ya V; Morshnev, S K; Starostin, N I; Gubin, V P [V.A.Kotel' nikov Institute of Radio Engineering and Electronics, Russian Academy of Sciences, Fryazino branch, Fryazino, Moscow Region (Russian Federation)

2015-11-30

The evolution of polarisation states (PS's) of broadband light propagating through a bent optical fibre with a helical structure of its refractive index anisotropy (hi-bi spun fibre) has been studied theoretically and experimentally. It has been shown that there exists a coordinate system of PS's in which the differential Jones matrix can be replaced by a diagonal matrix, which allows the polarisation parameters of the output broadband light to be readily calculated with sufficient accuracy. We have derived a formula for evaluating the magneto-optical sensitivity of a bent spun fibre. An approach has been proposed for restoring the degree of polarisation of light in a bent hi-bi spun fibre and, as a consequence, the visibility (contrast) of the interferometer in a current sensor with a sensing element based on the fibre under consideration. (optical fibres)

Hysteresis loops and the demagnetization process at 4.2 K for melt-spun Nd sub 1 sub 3 Fe sub 7 sub 7 B sub 1 sub 0

CERN Document Server

Jin Han Min; Park, W S; Park, M J; Wang Xue Feng

1998-01-01

Hysteresis loops of melt-spun Nd sub 1 sub 3 Fe sub 7 sub 7 B sub 1 sub 0 cooled down at the remanent state were measured at 4.2 K. The loop for fields of H sub m sub a sub x =6.4 MA m sup - sup 1 is characterized by low- and high-field steps. The loop for fields of H sub m sub a sub x =4.0 MA m sup - sup 1 is very thin with only a low-field step and is shifted profoundly along the H-axes. The loops and the spin distribution during the demagnetization process were analysed by micromagnetic finite-element calculations. Quantitatively, the calculations reproduce the experimental loops fairly well. The spin distribution is fairly nonuniform, and a domain-wall-like distribution appears not only at some grain boundaries but also within some grains at the high-field step. The demagnetization proceeds by nonuniform reversion as a whole, and neither the model of single-domain reversion nor the model of domain-wall pinning in the grain boundary model describes the process appropriately. (author)

Effect of P addition on glass forming ability and soft magnetic properties of melt-spun FeSiBCuC alloy ribbons

International Nuclear Information System (INIS)

Xu, J.; Yang, Y.Z.; Li, W.; Chen, X.C.; Xie, Z.W.

2016-01-01

The dependency of phosphorous content on the glass forming ability, thermal stability and soft magnetic properties of Fe 83.4 Si 2 B 14−x P x Cu 0.5 C 0.1 (x=0,1,2,3,4) alloys was investigated. The experimental results showed that the substitution of B by P increased the glass forming ability in this alloy system. The Fe 83.4 Si 2 B 10 P 4 Cu 0.5 C 0.1 alloy shows a fully amorphous character. Thermal stability of melt-spun ribbons increases and temperature interval between the first and second crystallization peaks enlarges with the increase of P content. And the saturation magnetic flux density (Bs) shows a slight increase with the increase of P content. The Fe 83.4 Si 2 B 11 P 3 Cu 0.5 C 0.1 nanocrystalline alloy exhibits a high Bs about 200.6 emu/g. The Bs of fully amorphous alloy Fe 83.4 Si 2 B 10 P 4 Cu 0.5 C 0.1 drops dramatically to 172.1 emu/g, which is lower than that of other nanocrystallines. Low material cost and excellent soft magnetic properties make the FeSiBPCuC alloys promise soft magnetic materials for industrial applications. - Highlights: • Partial substituting B by P helps to improve the glass forming ability of the alloy. • The addition of P content reduces the thermal stability and improves heat treatment temperature region for these alloys. • The Fe 83.4 Si 2 B 11 P 3 Cu 0.5 C 0.1 nanocrystalline alloy exhibits a high saturation magnetic density of 200.6 emu/g.

Investigations on sysnthesis, characterization and hydrogenation behaviour of the spin- and thermal-melted versions of LaNi{sub 5-x}Si{sub x}(x=0.1, 0.3, 0.5) hydrogen storage materials

Energy Technology Data Exchange (ETDEWEB)

Srivastava, S.; Srivastava, O.N. [Banaras Hindu Univ., Varanasi (India). Dept. of Physics

1998-03-06

The present study deals with investigations on the synthesis and characterisation of negative electrode material for high energy density Ni-MH battery. The hydrogen storage material (MH) has been synthesised trough normal casting and melt-spinning techniques. In LaNi{sub 5}/MmNi{sub 5} family various substitutions like Al, Mn, Co have been studied. The substitution of metalloid like Si is known to be very helpful in improving several hydrogenation properties. In the present study, the Si substituted versions of AB{sub 5}-type storage materials typified by LaNi{sub 5-x}Si{sub x} (x=0.1, 0.3, 0.5) habe been investigated. A comparison between the present material and the conventional AB{sub 5}-type material MmNi{sub 4.3}Al{sub 0.3}Mn{sub 0.4} has been made which has been previously studied. The main features revealed by XRD characterisations are the existence of the free Ni and Si together with AB{sub 5} material for all the three compositions. These free Ni and Si were found to disappear and yield, giving rise to a singular material after hydrogenation. The melt-spun version of the material was found to grow invariably in a direction perpendicular to the c-axis. The kinetics and activation process was better for the melt-spun version of the LaNi{sub 4.7}Si{sub 0.3} alloy than its thermally-melted counterpart (bulk) as well as to the alloy MmNi{sub 4.3}Al{sub 0.3}Mn{sub 0.4}. For example, the kinetics of the melt-spun version of LaNi{sub 4.7}Si{sub 0.3} is 60% faster than its bulk version and 70% faster than the melt-spun version of MmNi{sub 4.3}Al{sub 0.3}Mn{sub 0.4}. Similarly, the melt-spund version of the alloy LaNi{sub 4.7}Si{sub 0.3} gets activated in the 2nd cycle itself where as the alloy MmNi{sub 4.3}Al{sub 0.3}Mn{sub 0.4} attains this stage only in the 6th cycle. (orig.) 13 refs.

A linear dynamic model for rotor-spun composite yarn spinning process

International Nuclear Information System (INIS)

Yang, R H; Wang, S Y

2008-01-01

A linear dynamic model is established for the stable rotor-spun composite yarn spinning process. Approximate oscillating frequencies in the vertical and horizontal directions are obtained. By suitable choice of certain processing parameters, the mixture construction after the convergent point can be optimally matched. The presented study is expected to provide a general pathway to understand the motion of the rotor-spun composite yarn spinning process

Coupling characteristics of the spun optical fiber with triple stress elements

Science.gov (United States)

Ji, Minning; Shang, Fengtao; Chen, Dandan

2018-06-01

An empirical formula related to the stress field distribution in the optical fiber with triple stress elements is proposed and proved. The possible intercoupling between the fundamental modes and the higher order modes is demonstrated. The transmission property of the spun optical fiber with triple stress elements is analyzed. The experimental data from a sample of the spun optical fiber with triple stress elements confirm the theoretical results very well.

Magnetic and microstructural investigation of high-coercivity net-shape Nd–Fe–B-type magnets produced from spark-plasma-sintered melt-spun ribbons blended with DyF{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Žagar, Kristina, E-mail: kristina.zagar@ijs.si; Kocjan, Andraž; Kobe, Spomenka

2016-04-01

Nanostructured Nd–Fe–B-type materials produced by melt-spinning (MS) are used in a variety of applications in the electronics, automotive, and sensor industries. The very rapid MS process leads to flake-like powders with metastable, nanoscale, Nd{sub 2}Fe{sub 14}B grains. These powders are then formed into net-shaped, isotropic, polymer-bonded magnets, or they are hot formed into fully dense, metallic magnets that are isotropic and anisotropic. These fully dense magnets are usually produced with a conventional hot press without the inclusion of additives prior to the hot pressing. As a result, their properties, particularly the coercivity (H{sub ci}), are insufficient at automotive-relevant temperatures of 100–150 °C since the material H{sub ci} has a large temperature coefficient. In this study, we instead add a thin layer of DyF{sub 3} to the melt-spun ribbons prior to their hot consolidation in order to enhance the coercivity through a diffusion-based, partial substitution of the Nd by Dy. This is accomplished by applying extremely rapid, spark-plasma sintering to minimize any growth of the nanoscale Nd{sub 2}Fe{sub 14}B grains during consolidation. The result is a very high-coercivity magnet with drastically reduced amounts of heavy rare earths that is suitable for high-temperature applications. This work clearly demonstrates how rapidly formed, metastable states can provide us with properties that are unobtainable with conventional techniques. - Highlights: • We produced high coercivity magnets with drastically reduced amounts of HRE. • Microstructural analysis was conducted of the “free” and “wheel” side of Dy-treated Nd{sub 2}Fe{sub 14}B ribbons. • Dy-diffusion mechanism into ribbons depending on processing parameters is shown.

Analytical Approach to Polarization Mode Dispersion in Linearly Spun Fiber with Birefringence

Directory of Open Access Journals (Sweden)

Vinod K. Mishra

2016-01-01

Full Text Available The behavior of Polarization Mode Dispersion (PMD in spun optical fiber is a topic of great interest in optical networking. Earlier work in this area has focused more on approximate or numerical solutions. In this paper we present analytical results for PMD in spun fibers with triangular spin profile function. It is found that in some parameter ranges the analytical results differ from the approximations.

Giant magnetoresistance in melt spun Cu85Co10Ni5

DEFF Research Database (Denmark)

Curiotto, Stefano; Johnson, Erik; Celegato, Federica

2009-01-01

CuCoNi rapidly solidified alloys are interesting because they display giant magnetoresistance (GMR). In the present work a Cu85Co10Ni5 alloy has been synthesized by melt spinning and analysed for GMR. The ribbons obtained have been annealed at different temperatures and the evolution of the crystal...... structure with annealing has been studied by X-ray diffraction. The. ne microstructure has been observed by TEM and related to the magnetic properties, investigated in a vibrating sample magnetometer. In the studied composition the magnetoresistance was found to be lower than in binary CuCo alloys without...

Magnetocaloric effect in textured rare earth intermetallic compound ErNi

Directory of Open Access Journals (Sweden)

Aparna Sankar

2018-05-01

Full Text Available Melt-spun ErNi crystallizes in orthorhombic FeB-type structure (Space group Pnma, no. 62 similar to the arc-melted ErNi compound. Room temperature X-ray diffraction (XRD experiments reveal the presence of texture and preferred crystal orientation in the melt-spun ErNi. The XRD data obtained from the free surface of the melt-spun ErNi show large intensity enhancement for (1 0 2 Bragg reflection. The scanning electron microscopy image of the free surface depicts a granular microstructure with grains of ∼1 μm size. The arc-melted and the melt-spun ErNi compounds order ferromagnetically at 11 K and 10 K (TC respectively. Field dependent magnetization (M-H at 2 K shows saturation behaviour and the saturation magnetization value is 7.2 μB/f.u. for the arc-melted ErNi and 7.4 μB/f.u. for the melt-spun ErNi. The isothermal magnetic entropy change (ΔSm close to TC has been calculated from the M-H data. The maximum isothermal magnetic entropy change, -ΔSmmax, is ∼27 Jkg-1K-1 and ∼24 Jkg-1K-1 for the arc-melted and melt-spun ErNi for 50 kOe field change, near TC. The corresponding relative cooling power values are ∼440 J/kg and ∼432 J/kg respectively. Although a part of ΔSm is lost to crystalline electric field (CEF effects, the magnetocaloric effect is substantially large at 10 K, thus rendering melt-spun ErNi to be useful in low temperature magnetic refrigeration applications such as helium gas liquefaction.

Magnetocaloric effect in textured rare earth intermetallic compound ErNi

Science.gov (United States)

Sankar, Aparna; Chelvane, J. Arout; Morozkin, A. V.; Nigam, A. K.; Quezado, S.; Malik, S. K.; Nirmala, R.

2018-05-01

Melt-spun ErNi crystallizes in orthorhombic FeB-type structure (Space group Pnma, no. 62) similar to the arc-melted ErNi compound. Room temperature X-ray diffraction (XRD) experiments reveal the presence of texture and preferred crystal orientation in the melt-spun ErNi. The XRD data obtained from the free surface of the melt-spun ErNi show large intensity enhancement for (1 0 2) Bragg reflection. The scanning electron microscopy image of the free surface depicts a granular microstructure with grains of ˜1 μm size. The arc-melted and the melt-spun ErNi compounds order ferromagnetically at 11 K and 10 K (TC) respectively. Field dependent magnetization (M-H) at 2 K shows saturation behaviour and the saturation magnetization value is 7.2 μB/f.u. for the arc-melted ErNi and 7.4 μB/f.u. for the melt-spun ErNi. The isothermal magnetic entropy change (ΔSm) close to TC has been calculated from the M-H data. The maximum isothermal magnetic entropy change, -ΔSmmax, is ˜27 Jkg-1K-1 and ˜24 Jkg-1K-1 for the arc-melted and melt-spun ErNi for 50 kOe field change, near TC. The corresponding relative cooling power values are ˜440 J/kg and ˜432 J/kg respectively. Although a part of ΔSm is lost to crystalline electric field (CEF) effects, the magnetocaloric effect is substantially large at 10 K, thus rendering melt-spun ErNi to be useful in low temperature magnetic refrigeration applications such as helium gas liquefaction.

Magnetic properties improvement of melt spun Co{sub 86.5}Hf{sub 11.5}B{sub 2} nanocomposites by refractory elements substitution

Energy Technology Data Exchange (ETDEWEB)

Chang, H.W. [Department of Applied Physics, Tunghai University, Taichung 407, Taiwan (China); Lin, Y.H.; Shih, C.W.; Liao, M.C.; Lee, Y.I. [Department of Physics, National Chung Cheng University, Chia-Yi 621, Taiwan (China); Chang, W.C., E-mail: phywcc@ccu.edu.tw [Department of Physics, National Chung Cheng University, Chia-Yi 621, Taiwan (China); Yang, C.C. [Department of Physics, Chung-Yuan Christian University, Chungli 320, Taiwan (China); Shaw, C.C. [Superrite Electronics Co. Ltd., Taipei 111, Taiwan (China)

2016-03-01

Magnetic properties of melt spun Co{sub 86.5}Hf{sub 10.5}MB{sub 2} ribbons with refractory elements substitution (M=Cr, Nb, Ti, Zr) have been studied. For ternary Co{sub 86.5}Hf{sub 11.5}B{sub 2} ribbon, permanent magnetic properties of B{sub r}=0.71 T, {sub i}H{sub c}=192 kA/m, and (BH){sub max}=34.4 kJ/m{sup 3} are obtained, and they are significantly improved to B{sub r}=0.73–0.76 T, {sub i}H{sub c}=136–216 kA/m and (BH){sub max}=38.4–52.8 kJ/m{sup 3} with M substitution. Summarized with the results of x-ray diffraction refinement, thermal magnetic analysis, and transmission electron microscopy, the Co{sub 86.5}Hf{sub 10.5}MB{sub 2} nanocomposites following the optimal crystallization treatment mainly consist of orthorhombic 7:1 and face-center-cubic Co phases. Fine microstructure with average grain size in the range of 12.5−19.6 nm promotes exchange coupling effect between magnetic grains, thus improving permanent magnetic properties. The magnetic field dependence of coercivity reveals that coercivity of the studied Co{sub 86.5}Hf{sub 10.5}MB{sub 2} nonocomposites is mainly governed by the reverse domain nucleation mechanism. - Highlights: • M substitution refines the grain size. • M substitution strengthens the exchange coupling effect between grains. • M substitution improves hard magnetic properties of Co{sub 86.5}Hf{sub 10.5}MB{sub 2} ribbons. • The coercivity is mainly governed by the reverse domain nucleation mechanism. • Co{sub 86.5}Hf{sub 10.5}MB{sub 2} ribbons are relevant candidate for RE free permanent magnets.

Significant enhancement in thermoelectric performance of nanostructured higher manganese silicides synthesized employing a melt spinning technique.

Science.gov (United States)

Muthiah, Saravanan; Singh, R C; Pathak, B D; Avasthi, Piyush Kumar; Kumar, Rishikesh; Kumar, Anil; Srivastava, A K; Dhar, Ajay

2018-01-25

The limited thermoelectric performance of p-type Higher Manganese Silicides (HMS) in terms of their low figure-of-merit (ZT), which is far below unity, is the main bottle-neck for realising an efficient HMS based thermoelectric generator, which has been recognized as the most promising material for harnessing waste-heat in the mid-temperature range, owing to its thermal stability, earth-abundant and environmentally friendly nature of its constituent elements. We report a significant enhancement in the thermoelectric performance of nanostructured HMS synthesized using rapid solidification by optimizing the cooling rates during melt-spinning followed by spark plasma sintering of the resulting melt-spun ribbons. By employing this experimental strategy, an unprecedented ZT ∼ 0.82 at 800 K was realized in spark plasma sintered 5 at% Al-doped MnSi 1.73 HMS, melt spun at an optimized high cooling rate of ∼2 × 10 7 K s -1 . This enhancement in ZT represents a ∼25% increase over the best reported values thus far for HMS and primarily originates from a nano-crystalline microstructure consisting of a HMS matrix (20-40 nm) with excess Si (3-9 nm) uniformly distributed in it. This nanostructure, resulting from the high cooling rates employed during the melt-spinning of HMS, introduces a high density of nano-crystallite boundaries in a wide spectrum of nano-scale dimensions, which scatter the low-to-mid-wavelength heat-carrying phonons. This abundant phonon scattering results in a significantly reduced thermal conductivity of ∼1.5 W m -1 K -1 at 800 K, which primarily contributes to the enhancement in ZT.

Magnetic studies of melt spun NdFeAl-C alloys

International Nuclear Information System (INIS)

Rodriguez Torres, C.E.; Cabrera, A.F.; Sanchez, F.H.; Billoni, O.V.; Urreta, S.E.; Fabietti, L.M.

2004-01-01

Alloys with compositions Nd 60-x C x Fe 30 Al 10 (x=0, 1, 5 and 10) were processed by melt spinning at a tangential speed of 5 m/s. The as-cast ribbons were characterized by X-ray diffraction, Moessbauer Effect spectroscopy and their room temperature hysteresis loops. The substitution of Nd by C is found to affect the phase selection, from mainly DHCP-Nd for x=0 to DHCP-Nd /FCC-Nd for the other ones. Moessbauer spectra of all the as-cast samples indicate that Fe is present in crystalline magnetic phases as well as in a paramagnetic one. The major crystalline phase was identified as a μ-type (or A1) metastable phase, which is reported to have a large anisotropy field and a relatively high saturation polarization. Interstitial C stabilizes the μ-type phase and improves its average hyperfine field. The magnetic measurements display an increase of coercivity and remanence with the C concentration

Effect of rapid quenching on the magnetism and magnetocaloric effect of equiatomic rare earth intermetallic compounds RNi (R = Gd, Tb and Ho)

Energy Technology Data Exchange (ETDEWEB)

Rajivgandhi, R. [Department of Physics, Indian Institute of Technology Madras, Chennai 600 036 (India); Arout Chelvane, J. [Defence Metallurgical Research Laboratory, Hyderabad 500 058 (India); Quezado, S.; Malik, S.K. [Departamento de F’ısica Teorica e Experimental, Universidade Federal do Rio Grande do Norte, Natal 59072-970 (Brazil); Nirmala, R., E-mail: nirmala@physics.iitm.ac.in [Department of Physics, Indian Institute of Technology Madras, Chennai 600 036 (India)

2017-07-01

Highlights: • Melt-spinning yields microcrystalline RNi (R = Gd, Tb and Ho) samples with texture. • The texture-induced anisotropy affects magnetic and magnetocaloric properties. • Melt-spinning helps one engineer magnetocaloric effect in rare-earth compounds. - Abstract: Magnetocaloric effect (MCE) in RNi (where R = Gd, Tb and Ho) compounds has been studied in their arc-melted and melt-spun forms. The compound GdNi has the orthorhombic CrB-type structure (Space group Cmcm, No. 63) and the compound HoNi has the orthorhombic FeB-type structure (Space group Pnma, No. 62) at room temperature regardless of their synthesis condition. However, arc-melted TbNi orders in a monoclinic structure (Space group P2{sub 1}/m, No. 11) and when it is rapidly quenched to a melt-spun form, it crystallizes in an orthorhombic structure (Space group Pnma, No. 62). The arc-melted GdNi, TbNi and HoNi compounds order ferromagnetically at ∼69 K, ∼67 K and ∼36 K (T{sub C}) respectively. While the melt-spun GdNi shows about 6 K increase in T{sub C}, the ordering temperature of TbNi remains nearly the same in both arc-melted and melt-spun forms. In contrast, a reduction in T{sub C} by about 8 K is observed in melt-spun HoNi, when compared to its arc-melted counterpart. Isothermal magnetic entropy change, ∆S{sub m}, calculated from the field dependent magnetization data indicates an enhanced relative cooling power (RCP) for melt-spun GdNi for field changes of 20 kOe and 50 kOe. A lowered RCP value is observed in melt-spun TbNi and HoNi. These changes could have resulted from the competing shape anisotropy and the granular microstructure induced by the melt-spinning process. Tailoring the MCE of rare earth intermetallic compounds by suitably controlled synthesis techniques is certainly one of the directions to go forward in the search of giant magnetocaloric materials.

OPTICAL FIBRES AND FIBREOPTIC SENSORS: Spun microstructured optical fibresfor Faraday effect current sensors

Science.gov (United States)

Chamorovsky, Yury K.; Starostin, Nikolay I.; Morshnev, Sergey K.; Gubin, Vladimir P.; Ryabko, Maksim V.; Sazonov, Aleksandr I.; Vorob'ev, Igor'L.

2009-11-01

We report a simple design of spun holey fibres and the first experimental study of the magneto-optical response of spun microstructured fibres with high built-in birefringence. Such fibres enable the Faraday-effect-induced phase shift to effectively accumulate in a magnetic field even at very small coiling diameters. For example, the magneto-optical sensitivity of a 5-mm-diameter fibre coil consisting of 100 turns is ~70% that of an ideal fibre, in good agreement with theoretical predictions.

Electrochemical hydrogen storage behaviour of as-cast and as-spun RE-Mg-Ni-Mn-based alloys applied to Ni-MH battery

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yanghuan; Hou, Zhonghui; Hu, Feng [Inner Mongolia University of Science and Technology, Baotou (China). Key Laboratory of Integrated Exploitation of Baiyun Obo Multi-Metal Resources; Central Iron and Steel Research Institute, Beijing (China). Dept. of Functional Material Research; Cai, Ying [Inner Mongolia University of Science and Technology, Baotou (China). Key Laboratory of Integrated Exploitation of Baiyun Obo Multi-Metal Resources; Qi, Yan; Zhao, Dongliang [Central Iron and Steel Research Institute, Beijing (China). Dept. of Functional Material Research

2016-09-15

La-Mg-Ni-Mn-based AB{sub 2}-type La{sub 1-x}Ce{sub x}MgNi{sub 3.5}Mn{sub 0.5} (x = 0, 0.1, 0.2, 0.3, 0.4) alloys were fabricated by melt spinning. X-ray diffraction and scanning electron microscopy revealed that the experimental alloys consisted of a major phase LaMgNi{sub 4} and a secondary phase LaNi{sub 5}. The Ce substitution for La and melt spinning refined the grains of the alloys clearly. Electrochemical tests showed that the as-cast and as-spun alloys exhibited excellent activation capability. With the increase in the spinning rate and Ce content, the discharge capacities of the alloys initially increased and then decreased, whereas their cycle stabilities always increased. Moreover, the electrochemical kinetics of the alloys initially increased and then decreased with the growth of Ce content and spinning rate. The major reason leading to the capacity degradation of the alloy electrodes was determined to be the pulverisation of the alloy particles and the corrosion and oxidation of the alloy surface.

Interactive contribution of grain size and grain orientation to coercivity of melt spun ribbons

International Nuclear Information System (INIS)

Wang, N.; Li, G.; Yao, W.J.; Wen, X.X.

2010-01-01

During melt spinning process, the improvement of certain grain orientation and the refinement of grain size with surface velocity have interactive and contradictory effects on the magnetic properties. The contributions of these effects have seldom been taken into account and they were discussed in this paper via Fe-2, 4, 6.5 wt% Si alloys. Heat treatment at 1173 K for 1 h was performed to show the annealing impact. The X-ray diffraction patterns show that the high surface velocity and heat treatment increase the intensity ratio of line (2 0 0) to (1 1 0) of A2 phase. The (2 0 0) line corresponds to (2 0 0) plane in direction, easy magnetization direction of α-Fe phase in Fe-Si alloy. The improvement of this grain orientation with the surface velocity decreases the coercivity, which should increase due to the grain refinement. It is revealed that the texture promoted by the anisotropic heat release during melt spinning process is one factor to improve the magnetic properties and should be considered when preparing soft magnetic materials.

Enhancing the Dyeability of Polypropylene Fibers by Melt Blending with Polyethylene Terephthalate

Directory of Open Access Journals (Sweden)

Fereshteh Mirjalili

2013-01-01

Full Text Available Attempts were made to modify polypropylene fibers by melt blending with polyethylene terephthalate in order to enhance the dyeability of the resultant fiber. Five blends of polypropylene/polyethylene terephthalate/compatibilizer were prepared and subsequently spun into fibers. Three disperse dyes were used to dye such modified fibers at boiling and 130°C. The dyeing performance of the blend fibers, as well as the morphological, chemical, thermal, and mechanical properties, of the corresponding blends was characterized by means of spectrophotometry, polarized optical microscopy, scanning electron microscopy (SEM, FT-IR spectroscopy, differential scanning calorimetry (DSC, and tensile testing.

Spider Silk Fibers Spun from Soluble Recombinant Silk Produced in Mammalian Cells

Science.gov (United States)

Lazaris, Anthoula; Arcidiacono, Steven; Huang, Yue; Zhou, Jiang-Feng; Duguay, François; Chretien, Nathalie; Welsh, Elizabeth A.; Soares, Jason W.; Karatzas, Costas N.

2002-01-01

Spider silks are protein-based ``biopolymer'' filaments or threads secreted by specialized epithelial cells as concentrated soluble precursors of highly repetitive primary sequences. Spider dragline silk is a flexible, lightweight fiber of extraordinary strength and toughness comparable to that of synthetic high-performance fibers. We sought to ``biomimic'' the process of spider silk production by expressing in mammalian cells the dragline silk genes (ADF-3/MaSpII and MaSpI) of two spider species. We produced soluble recombinant (rc)-dragline silk proteins with molecular masses of 60 to 140 kilodaltons. We demonstrated the wet spinning of silk monofilaments spun from a concentrated aqueous solution of soluble rc-spider silk protein (ADF-3; 60 kilodaltons) under modest shear and coagulation conditions. The spun fibers were water insoluble with a fine diameter (10 to 40 micrometers) and exhibited toughness and modulus values comparable to those of native dragline silks but with lower tenacity. Dope solutions with rc-silk protein concentrations >20% and postspinning draw were necessary to achieve improved mechanical properties of the spun fibers. Fiber properties correlated with finer fiber diameter and increased birefringence.

Colorimetric Sensor for Detection of Adulteration in Gasoline using Polydiacetyleneelectro-Spun Fibers

Directory of Open Access Journals (Sweden)

Shamshad Ali

2016-06-01

Full Text Available We report the successful incorporation of pentacosadiynoic acid (PCDA in poly(Ɛ-caprolactone (PCL by electro-spinning technique for sensor application. The UV-polymerization of the resulting electro-spun fibers mats (EFMs produced polydiacetylenes (PDA polymer exhibiting blue color. The PCL-PDA EFMs were characterized by Raman Spectroscopy, UV-Vis Spectroscopy and FE-SEM analysis. Sensor test results revealed that the treatment of the PCL-PDA EFMs with adulterated gasoline showed a blue to red color transitionrapidly. FE-SEM images demonstrated that the thinner or toluene used as an adulterant in the gasoline destroyed the PCL electro-spun fibers; which gave access to PDA polymer producing red color.

An investigation on hydrogen storage kinetics of nanocrystalline and amorphous Mg2Ni1-xCox (x = 0-0.4) alloy prepared by melt spinning

International Nuclear Information System (INIS)

Zhang Yanghuan; Li Baowei; Ren Huipin; Ding Xiaoxia; Liu Xiaogang; Chen Lele

2011-01-01

Research highlights: → The investigation of the structures of the Mg 2 Ni 1-x Co x (x = 0, 0.1, 0.2, 0.3, 0.4) alloys indicates that a nanocrystalline and amorphous structure can be obtained in the experiment alloys by melt spinning technology. The substitution of Co for Ni facilitates the glass formation in the Mg 2 Ni-type alloy. And the amorphization degree of the alloys visibly increases with increasing Co content. → Both the melt spinning and Co substitution significantly improve the hydrogen storage kinetics of the alloys. The hydrogen absorption saturation ratio (R t a ) and hydrogen desorption ratio (R t d ) as well as the high rate discharge ability (HRD) increase with rising spinning rate and Co content. The hydrogen diffusion coefficient (D), the Tafel polarization curves and the electrochemical impedance spectra (EIS) measurements show that the electrochemical kinetics notably increases with rising spinning rate and Co content. → Furthermore, all the as-spun alloys, when the spinning rate reaches to 30 m/s, have nearly same hydrogen absorption kinetics, indicating that the hydrogen absorption kinetics of the as-spun alloy is predominately controlled by diffusion ability of hydrogen atoms. - Abstract: In order to improve the hydrogen storage kinetics of the Mg 2 Ni-type alloys, Ni in the alloy was partially substituted by element Co, and melt-spinning technology was used for the preparation of the Mg 2 Ni 1-x Co x (x = 0, 0.1, 0.2, 0.3, 0.4) hydrogen storage alloys. The structures of the as-cast and spun alloys are characterized by XRD, SEM and TEM. The hydrogen absorption and desorption kinetics of the alloys were measured by an automatically controlled Sieverts apparatus. The electrochemical hydrogen storage kinetics of the as-spun alloys is tested by an automatic galvanostatic system. The hydrogen diffusion coefficients in the alloys are calculated by virtue of potential-step method. The electrochemical impedance spectrums (EIS) and the Tafel

Investigating the provenance of un-dyed spun cotton fibre using multi-isotope profiles and chemometric analysis.

Science.gov (United States)

Daéid, Niamh Nic; Meier-Augenstein, Wolfram; Kemp, Helen F

2011-07-15

The analysis of un-dyed spun cotton fibres can be challenging within a forensic science context where discrimination of one fibre from another is of importance. Conventional microscopic and chemical analysis of these fibres is generally unsuccessful because of their similar morphology. In this work we have explored the potential of isotope ratio mass spectrometry (IRMS) as a tool for spun cotton fibre analysis in an attempt to reveal any discriminatory information available. Seven different batches of un-dyed spun cotton fibre from four different countries were analysed. A combination of the hydrogen and oxygen isotopic data facilitated the correct association of the samples, demonstrating, for the first time, the applicability of IRMS to fibre analysis in this way. Copyright © 2011 John Wiley & Sons, Ltd.

Solvent-free preparation of polylactic acid fibers by melt electrospinning using umbrella-like spray head and alleviation of problematic thermal degradation

Directory of Open Access Journals (Sweden)

Liu Yong

2012-01-01

Full Text Available Melt electrospinning is an even simpler and safer method compared with the solution electrospinning in the production of ultra-fine fibers. Polylactic acid (PLA is a biodegradable and resorbable aliphatic ester that has received significant attention in recent years. PLA is easily degradable at high temperature in the process of melt electrospinning. High efficient fibers were made using our designed umbrella-like spray head spinning facility in this work. To find how to alleviate the problematic degradation and what factors could be relevant to degradation, temperature, relative molecular mass, Differential Scanning Calorimeter and X-ray Diffraction patterns before and after spinning were investigated and compared with each other. Results showed that fibers were facile shorten and fractured when spun at 245°C while the relative molecular mass of PLA fibers decreased markedly as compared with that spun at 210°C. To hinder the degradation, couple of experimental efforts were implemented with adding antioxidants, raising spinning voltage, lowering temperature, and reducing residence time. After such efforts, it was observed that the relative molecular mass of the PLA fibers was higher than those without inputting any efforts. The effect of antioxidant 1010 was found the most promising on the alleviation of PLA problematic thermal degradation.

Improved technology for spun-cast concrete poles

Energy Technology Data Exchange (ETDEWEB)

Dilger, W H; Ghali, A

1984-07-01

Different types of concrete were investigated with the goal of developing concrete suitable for the production of spun-cast concrete poles. A total of 65 different concrete mixes were investigated, with the suitability criteria defined as: compactability, no segregation of the mix components during the spinning operation, no shrinkage cracking, high strength, and durability. High strength normal weight concretes and semi-lightweight concretes, both with and without fly ash and/or silica fume and with different types of admixtures were used to produce spun-cast concrete pole segments. Of the 35 lightweight concretes only 3 were considered successful, as in all other specimens the inner layer of coarse aggregate was not well embedded in the mortar, and many mixes could not be compacted properly because they were too stiff, too wet, or started to set before spinning commenced. The three successful specimens contained fly ash and one contained silica fume, and had low water/cement ratios (0.26 to 0.29). Of the 23 normal weight concretes tested, only 5 were considered suitable, and all these had a sand/coarse aggregate ratio of 0.25 or smaller and a cement content between 350 and 400 kg/m{sup 3}. A theoretical study of the stresses in the end zones of pretensioned poles is presented. 10 refs., 53 figs., 14 tabs.

Physical and electrical properties of melt-spun Fe-Si (3–8 wt.%) soft magnetic ribbons

Energy Technology Data Exchange (ETDEWEB)

Overman, Nicole R.; Jiang, Xiujuan; Kukkadapu, Ravi K.; Clark, Trevor; Roosendaal, Timothy J.; Coffey, Gregory; Shield, Jeffrey E.; Mathaudhu, Suveen N.

2018-02-01

Fe-Si alloys ranging from 3 to 8 wt% Si were rapidly solidified using melt spinning. Wheel speeds of 30 m/s and 40 m/s were employed to vary cooling rates. Mössbauer spectroscopic studies indicated the Si content significantly influenced the number of Fe sites, relative abundance of various Fe species, and internal magnetic fields/structural environments. Wheel speed altered Fe speciation only in the 3 wt% sample. Scanning electron microscopy confirmed that increasing the wheel speed refined both the ribbon thickness and grain size. Electron backscatter diffraction results suggest tailoring melt spinning process parameters and alloy chemistry may offer the ability to manipulate {001} texture development. Electrical resistivity measurements were observed to increase in response to elevated Si content. Increased hardness was correlated to elevated Si content and wheel speed.

Needs of caregivers of cancer patients: validation of the Mexican version of the Support Person Unmet Needs Survey (SPUNS-SFM).

Science.gov (United States)

Doubova, Svetlana V; Aguirre-Hernandez, Rebeca; Infante-Castañeda, Claudia; Martinez-Vega, Ingrid; Pérez-Cuevas, Ricardo

2015-10-01

The purpose of this study was to validate the Mexican version of the Support Person Unmet Needs Survey (SPUNS-SFM). A cross-sectional survey that included 826 primary caregivers of cancer patients was conducted from June to December 2013 at the Oncology Hospital of the Mexican Institute of Social Security in Mexico City. The validation procedure comprised (1) content validity through a group of experts; (2) construct validity through an exploratory factor analysis based on the polychoric correlation matrix; (3) internal consistency using Cronbach's alpha; (4) convergent validity between SPUNS-SFM and quality of life, anxiety-and-depression scales by calculating Spearman's rank correlation coefficient;( 5) discriminative validity through the Wilcoxon rank-sum test; and (6) test-retest reliability using intraclass correlation coefficient. SPUNS-SFM has 23 items with six factors accounting for 65 % of the total variance. The domains were concerns about the future, access and continuity of healthcare, information, work and finance, and personal and emotional needs. Cronbach's alpha values ranged from 0.70 to 0.88 among factors. SPUNS-SFM had moderate convergent validity compared with quality of life and depression-and-anxiety scales and good discriminative validity, revealing high needs for younger caregivers and more emotional needs for caregivers of patients with advanced cancer stages. Intraclass correlation coefficient between SPUNS-SFM measurements was 0.78. SPUNS-SFM is a valid and reliable tool to identify needs of caregivers of cancer patients.

Silver oxide nanoparticles embedded silk fibroin spuns: Microwave mediated preparation, characterization and their synergistic wound healing and anti-bacterial activity.

Science.gov (United States)

Babu, Punuri Jayasekhar; Doble, Mukesh; Raichur, Ashok M

2018-03-01

The synergistic wound healing and antibacterial activity of silver oxide nanoparticles embedded silk fibroin (Ag 2 O-SF) spuns is reported here. UV-Vis spectro photometric analysis of these spuns showed the surface plasmon resonance (SPR) confirming the formation of the silver oxide nanoparticles (Ag 2 O NPs) on the surface of the silk fibroin (SF). Scanning electron microscope (SEM) and Differential scanning calorimetry (DSC) also confirmed the presence of Ag 2 O NPs on surface of SF. X-ray diffraction (XRD) analysis revealed the crystalline nature of both SF and Ag 2 O-SF. Fourier transform infrared spectroscopy (FT-IR) results showed the different forms of silk (I and II) and their corresponding protein (amide I, II, III) confirmations. Biodegradation study revealed insignificant changes in the morphology of Ag 2 O-SF spuns even after 14 days of immersion in phosphate buffered saline (PBS). Ag 2 O-SF spuns showed excellent antibacterial activity against both pathogen (S. aureus and M. tuberculosis) and non-pathogen (E. coli) bacteria. More importantly, In vitro wound healing (scratch assay) assay revealed fast migration of the T3T fibroblast cells through the scratch area treated with extract of Ag 2 O-SF spuns and the area was completely covered within 24 h. Cytotoxicity assay confirmed the biocompatible nature of the Ag 2 O-SF spuns, thus suggesting an ideal material for wound healing and anti-bacterial applications. Copyright © 2017 Elsevier Inc. All rights reserved.

Estimation of the heat transfer coefficient in melt spinning process

International Nuclear Information System (INIS)

Tkatch, V I; Maksimov, V V; Grishin, A M

2009-01-01

Effect of the quenching wheel velocity in the range 20.7-26.5 m/s on the cooling rate as well as on the structure and microtopology of the contact surfaces of the glass-forming FeNiPB melt-spun ribbons has been experimentally studied. Both the values of the cooling rate and heat transfer coefficient at the wheel-ribbon interface estimated from the temperature vs. time curves recorded during melt spinning runs are in the ranges (1.6-5.2)x10 6 K/s and (2.8-5.2)x10 5 Wm -2 K -1 , respectively, for ribbon thicknesses of 31.4-22.0 μm. It was found that the density of the air pockets at the underside surface of ribbons decreases while its average depth remains essentially unchanged with the wheel velocity. Using the surface quality parameters the values of the heat transfer coefficient in the areas of direct ribbon-wheel contact were evaluated to be ranging from 5.75 to 6.65x10 5 Wm -2 K -1 .

Lithium-conducting ionic melt electrolytes from polyether-functionalized fluorosulfonimide anions

International Nuclear Information System (INIS)

Hallac, B.B.; Geiculescu, O.E.; Rajagopal, R.V.; Creager, S.E.; DesMarteau, D.D.

2008-01-01

Solvent-free lithium-conducting ionic melt (IM) electrolytes were synthesized and characterized with respect to chemical structure, purity, and ion transport properties. The melts consist of lithium (perfluorovinylether)sulfonimide salts attached covalently to a lithium-solvating polyether chain. Ionic conductivities are relatively high which is a consequence of the favorable combination of the low lattice energy of the lithium fluorosulfonimide salt (low basicity of the fluorosulfonimide anion), the relatively low viscosity of the polyether matrix, and the relatively high salt content of the melts. Galvanostatic dc polarization experiments, using cells with non-blocking Li electrodes, indicate that salt concentration polarization does not occur in these electrolytes as dc current is passed through them

Solidification structure and dispersoids in rapidly solidified Ti-Al-Sn-Zr-Er-B alloys

International Nuclear Information System (INIS)

Rowe, R.G.; Broderick, T.F.; Koch, E.F.; Froes, F.H.

1986-01-01

The microstructure of melt extracted and melt spun titanium alloys containing erbium and boron revealed a duplex solidification structure of columnar grains leading to equiaxed and dendritic structures near the free surface of melt extracted and melt spun alloys. The solidification structure was revealed by apparent boride segregation to cellular, interdendritic and grain boundaries. Precipitation of needle or lath-like TiB particles occurred adjacent to Er/sub 2/O/sub 3/ dispesoid particles in as-rapidly solidified ribbon

Optical yarn assessment system for twist measurement in rotor-spun yarn

International Nuclear Information System (INIS)

Jhatial, R.A.

2015-01-01

This paper presents the development of an optical yarn assessment system for evaluation of twist and structure of twisted yarn. The system comprises a yarn carriage unit, a video microscope and a personal computer. This system was used in conjunction with the well-known tracer fibre technique. This system enables digital images to be grabbed and continuous movies of the yarn to be recorded in order to facilitate the measurement of twist and the analysis of yarn structure. Yarn samples from polyester, viscose and cotton with 35 tex and 485 turns/meter were spun from the roving with 2.3% of black fibres on the SKF laboratory ring frame. In order to measure the twist in the rotor yarns with the optical yarn assessment system, a set of yarn samples from same fibres were spun on RU 14 rotor machine with 35 tex and 475 turns/meter. The twist was measured with the optical yarn assessment system and sixty tests of each sample were carried out on the Zweigle D301. It is clear from the results that there is consistency in the twist of ring-spun yarn measured by the optical yarn assessment system. However, the measured twist with the Zwiegle D301 is inconsistent in the different yarns. The difference in the mean twist measured with the optical twist measuring system and the double untwist-twist method was not significant at a 5% probability level when data was analyzed with t test by using SPSS (Statistical Package for Social Sciences). (author)

Neutron diffraction study on the magnetic structure of Fe{sub 2}P-based Mn{sub 0.66}Fe{sub 1.29}P{sub 1−x}Si{sub x} melt-spun ribbons

Energy Technology Data Exchange (ETDEWEB)

Ou, Z.Q., E-mail: z.ou@tudelft.nl [Fundamental Aspects of Materials and Energy, Faculty of Applied Sciences, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands); Zhang, L. [Fundamental Aspects of Materials and Energy, Faculty of Applied Sciences, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands); BASF Nederland B.V., Strijkviertel 67, 3454PK De Meern (Netherlands); Dung, N.H. [Fundamental Aspects of Materials and Energy, Faculty of Applied Sciences, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands); Eijck, L. van [Neutron and Positron Methods in Materials, Faculty of Applied Sciences, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands); Mulders, A.M. [University of New South Wales in Canberra, Canberra, Australian Capital Territory 2600 (Australia); Avdeev, M. [Bragg Institute, Australian Nuclear Science and Technology Organization (ANSTO), Kirrawee DC NSW 2232 (Australia); Dijk, N.H. van; Brück, E. [Fundamental Aspects of Materials and Energy, Faculty of Applied Sciences, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands)

2013-08-15

We report on the magnetic and structural properties of Mn{sub 0.66}Fe{sub 1.29}P{sub 1−x}Si{sub x} melt-spun ribbons with 0.34≤x≤0.42 that are promising candidates for high-temperature magnetocaloric applications. A magnetic moment of up to 4.57 μ{sub B}/f.u. for x=0.34 indicates high magnetic density in the system, which is certainly advantageous for the magnetocaloric effects. Introducing site disorder at the 3g site by replacing 1/3 of Fe with Mn appears to enhance the magnetic interaction, while the strong magnetoelastic coupling is maintained. This site disorder also shows a stabilizing effect on the hexagonal crystal structure, which is maintained to a high Si content. The moment alignment within the crystallographic unit cell is also affected when the Si content is increased from x=0.34 to 0.42 in the Mn{sub 0.66}Fe{sub 1.29}P{sub 1−x}Si{sub x} compounds as the canting angle with respect to the c-direction increases. - Highlights: • The magnetic structure is determined using neutron diffraction. • A magnetic moment of up to 4.57 μ{sub B}/f.u. is observed. • Alignment of the magnetic moment is canted when varying the Si content. • The 3g site disorder shows a stabilizing effect on the hexagonal crystal structure.

Solution blow spun Poly(lactic acid)/Hydroxypropyl methylcellulose nanofibers with antimicrobial properties

Science.gov (United States)

Poly(lactic acid) (PLA) nanofibers containing hydroxypropyl methylcellulose (HPMC) and tetracycline hydrochloride (THC) were solution blow spun from two different solvents, chloroform/acetone (CA, 80:20 v/v) and 2,2,2-triflouroethanol (TFE). The diameter distribution, chemical, thermal, thermal stab...

Solid-state densification of spun-cast self-assembled monolayers for use in ultra-thin hybrid dielectrics

Energy Technology Data Exchange (ETDEWEB)

Hutchins, Daniel O.; Acton, Orb [Department of Materials Science and Engineering, University of Washington, Seattle, WA 98195 (United States); Weidner, Tobias [Department of Bioengineering, University of Washington, Seattle, WA 98195 (United States); Cernetic, Nathan [Department of Materials Science and Engineering, University of Washington, Seattle, WA 98195 (United States); Baio, Joe E. [Department of Chemical Engineering, University of Washington, Seattle, WA 98195 (United States); Castner, David G. [Department of Bioengineering, University of Washington, Seattle, WA 98195 (United States); Department of Chemical Engineering, University of Washington, Seattle, WA 98195 (United States); Ma, Hong, E-mail: hma@uw.edu [Department of Materials Science and Engineering, University of Washington, Seattle, WA 98195 (United States); Jen, Alex K.-Y., E-mail: ajen@uw.edu [Department of Materials Science and Engineering, University of Washington, Seattle, WA 98195 (United States); Department of Chemistry, University of Washington, Seattle, WA 98195 (United States)

2012-11-15

Highlights: Black-Right-Pointing-Pointer Rapid processing of SAM in ambient conditions is achieved by spin coating. Black-Right-Pointing-Pointer Thermal annealing of a bulk spun-cast molecular film is explored as a mechanism for SAM densification. Black-Right-Pointing-Pointer High-performance SAM-oxide hybrid dielectric is obtained utilizing a single wet processing step. - Abstract: Ultra-thin self-assembled monolayer (SAM)-oxide hybrid dielectrics have gained significant interest for their application in low-voltage organic thin film transistors (OTFTs). A [8-(11-phenoxy-undecyloxy)-octyl]phosphonic acid (PhO-19-PA) SAM on ultrathin AlO{sub x} (2.5 nm) has been developed to significantly enhance the dielectric performance of inorganic oxides through reduction of leakage current while maintaining similar capacitance to the underlying oxide structure. Rapid processing of this SAM in ambient conditions is achieved by spin coating, however, as-cast monolayer density is not sufficient for dielectric applications. Thermal annealing of a bulk spun-cast PhO-19-PA molecular film is explored as a mechanism for SAM densification. SAM density, or surface coverage, and order are examined as a function of annealing temperature. These SAM characteristics are probed through atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and near edge X-ray absorption fine structure spectroscopy (NEXAFS). It is found that at temperatures sufficient to melt the as-cast bulk molecular film, SAM densification is achieved; leading to a rapid processing technique for high performance SAM-oxide hybrid dielectric systems utilizing a single wet processing step. To demonstrate low-voltage devices based on this hybrid dielectric (with leakage current density of 7.7 Multiplication-Sign 10{sup -8} A cm{sup -2} and capacitance density of 0.62 {mu}F cm{sup -2} at 3 V), pentacene thin-film transistors (OTFTs) are fabricated and yield sub 2 V operation and charge carrier mobilites of up to

Effect of low-melting point phases on the microstructure and properties of spark plasma sintered and hot deformed Nd-Fe-B alloys

Science.gov (United States)

Zhang, Li; Wang, Meiyu; Yan, Xueliang; Lin, Ye; Shield, Jeffrey

2018-04-01

The effect of adding a low melting point Pr-Cu-Al alloy during spark plasma sintering of melt-spun Nd-Fe-B ribbons is investigated. Regions of coarse grains were reduced and overall grain refinement was observed after the addition of Pr68Cu25Al7, leading to an enhancement of coercivity from 12.7 kOe to 20.4 kOe. Hot deformation of the samples in the spark plasma sintering system resulted in the formation of platelet-like grains, producing crystallographic alignment and magnetic anisotropy. The hot deformation process improved the remanence and energy product but reduced the coercivity. The decrease of coercivity resulted from grain growth and aggregation of Pr and Nd elements at triple-junction phases.

Microstructure and soft magnetic properties of Finemet-type ribbons obtained by twin-roller melt-spinning

International Nuclear Information System (INIS)

Pozo Lopez, G.; Fabietti, L.M.; Condo, A.M.; Urreta, S.E.

2010-01-01

Soft magnetic ribbons of Finemet-type (Fe 73.5 Cu 1 Nb 3 Si 13.5 B 9 ) alloys are synthesized by the twin-roller melt-spinning technique directly from the melt, at tangential wheel speeds of 15, 18, 19 and 20 m/s. The microstructure and the magnetic properties are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), differential thermal analysis (DTA), thermo-gravimetric analysis (TGA) and hysteresis loops measurements. Samples cooled at 20 m/s are amorphous, while those quenched at lower wheel speeds are partially crystalline. All samples studied present saturation magnetization values (150-160 A m 2 /kg) higher than the commercial Finemet alloys (∼135 A m 2 /kg), obtained by controlled crystallization of amorphous single-roller melt-spun alloys. Optimal soft magnetic properties - σ S =(154±8) A m 2 /kg and H C =(6.9±0.9) A/m - are found in samples quenched at 19 m/s, consisting of size-distributed bcc Fe-Si nanograins (∼18 nm in average) embedded in an amorphous residual matrix. A minority nanocrystalline magnetic phase (≤10 nm) is also detected.

Development of Maltodextrin-Based Immediate-Release Tablets Using an Integrated Twin-Screw Hot-Melt Extrusion and Injection-Molding Continuous Manufacturing Process.

Science.gov (United States)

Puri, Vibha; Brancazio, Dave; Desai, Parind M; Jensen, Keith D; Chun, Jung-Hoon; Myerson, Allan S; Trout, Bernhardt L

2017-11-01

The combination of hot-melt extrusion and injection molding (HME-IM) is a promising process technology for continuous manufacturing of tablets. However, there has been limited research on its application to formulate crystalline drug-containing immediate-release tablets. Furthermore, studies that have applied the HME-IM process to molded tablets have used a noncontinuous 2-step approach. The present study develops maltodextrin (MDX)-based extrusion-molded immediate-release tablets for a crystalline drug (griseofulvin) using an integrated twin-screw HME-IM continuous process. At 10% w/w drug loading, MDX was selected as the tablet matrix former based on a preliminary screen. Furthermore, liquid and solid polyols were evaluated for melt processing of MDX and for impact on tablet performance. Smooth-surfaced tablets, comprising crystalline griseofulvin solid suspension in the amorphous MDX-xylitol matrix, were produced by a continuous process on a twin-screw extruder coupled to a horizontally opening IM machine. Real-time HME process profiles were used to develop automated HME-IM cycles. Formulation adjustments overcame process challenges and improved tablet strength. The developed MDX tablets exhibited adequate strength and a fast-dissolving matrix (85% drug release in 20 min), and maintained performance on accelerated stability conditions. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Alloy composition dependence of formation of porous Ni prepared by rapid solidification and chemical dealloying

Energy Technology Data Exchange (ETDEWEB)

Qi Zhen [Key Laboratory of Liquid Structure and Heredity of Materials, Shandong University, Jingshi Road 73, Jinan 250061 (China); Zhang Zhonghua [Key Laboratory of Liquid Structure and Heredity of Materials, Shandong University, Jingshi Road 73, Jinan 250061 (China)], E-mail: zh_zhang@sdu.edu.cn; Jia Haoling [Key Laboratory of Liquid Structure and Heredity of Materials, Shandong University, Jingshi Road 73, Jinan 250061 (China); Qu Yingjie [Shandong Labor Occupational Technology College, Jingshi Road 388, Jinan 250022 (China); Liu Guodong; Bian Xiufang [Key Laboratory of Liquid Structure and Heredity of Materials, Shandong University, Jingshi Road 73, Jinan 250061 (China)

2009-03-20

In this paper, the effect of alloy composition on the formation of porous Ni catalysts prepared by chemical dealloying of rapidly solidified Al-Ni alloys has been investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis and N{sub 2} adsorption experiments. The experimental results show that rapid solidification and alloy composition have a significant effect on the phase constituent and microstructure of Al-Ni alloys. The melt spun Al-20 at.% Ni alloy consists of {alpha}-Al, NiAl{sub 3} and Ni{sub 2}Al{sub 3}, while the melt spun Al-25 and 31.5 at.% Ni alloys comprise NiAl{sub 3} and Ni{sub 2}Al{sub 3}. Moreover, the formation and microstructure of the porous Ni catalysts are dependent upon the composition of the melt spun Al-Ni alloys. The morphology and size of Ni particles in the Ni catalysts inherit from those of grains in the melt spun Al-Ni alloys. Rapid solidification can extend the alloy composition of Al-Ni alloys suitable for preparation of the Ni catalysts, and obviously accelerate the dealloying process of the Al-Ni alloys.

Quick scan IMS vendors

NARCIS (Netherlands)

Norp, A.H.J.; Pals, H.; Walraven, F.A.

2007-01-01

IMS is gaining momentum in the market. First operators are deploying IMS, while other operators are considering buying IMS. Operators have two approaches for introducing IMS and building an IMS eco-system: • Buying IMS from a large vendor or system integrator. Vendors like Alcatel-Lucent, Ericsson

Crystallinity of Electrospun and Centrifugal Spun Polycaprolactone Fibers: A Comparative Study

Directory of Open Access Journals (Sweden)

Eva Kuzelova Kostakova

2017-01-01

Full Text Available Crystalline properties of semicrystalline polymers are very important parameters that can influence the application area. The internal structure, like the mentioned crystalline properties, of polymers can be influenced by the production technology itself and by changing technology parameters. The present work is devoted to testing of electrospun and centrifugal spun fibrous and nanofibrous materials and compare them to foils and granules made from the same raw polymer. The test setup reveals the structural differences caused by the production technology. Effects of average molecular weight are also exhibited. The applied biodegradable and biocompatible polymer is polycaprolactone (PCL as it is a widespread material for medical purposes. The crystallinity of PCL has significant effect on rate of degradation that is an important parameter for a biodegradable material and determines the applicability. The results of differential scanning calorimetry (DSC showed that, at the degree of crystallinity, there is a minor difference between the electrospun and centrifugal spun fibrous materials. However, the significant influence of polymer molecular weight was exhibited. The morphology of the fibrous materials, represented by fiber diameter, also did not demonstrate any connection to final measured crystallinity degree of the tested materials.

Hydrogen storage in Mg-Ni-Fe compounds prepared by melt spinning and ball milling

Energy Technology Data Exchange (ETDEWEB)

Palade, P. [Settore Materiali, Dipartimento di Ingegneria Meccanica, Universita di Padova, via Marzolo 9, 35131 Padova (Italy); National Institute for Physics of Materials, Atomistilor 105 bis, P.O. Box MG-7, 077125 Bucharest-Magurele (Romania); Sartori, S. [Settore Materiali, Dipartimento di Ingegneria Meccanica, Universita di Padova, via Marzolo 9, 35131 Padova (Italy); Maddalena, A. [Settore Materiali, Dipartimento di Ingegneria Meccanica, Universita di Padova, via Marzolo 9, 35131 Padova (Italy); Principi, G. [Settore Materiali, Dipartimento di Ingegneria Meccanica, Universita di Padova, via Marzolo 9, 35131 Padova (Italy)]. E-mail: giovanni.principi@unipd.it; Lo Russo, S. [Dipartimento di Fisica, Universita di Padova, Via Marzolo 8, 35131 Padova (Italy); Lazarescu, M. [National Institute for Physics of Materials, Atomistilor 105 bis, P.O. Box MG-7, 077125 Bucharest-Magurele (Romania); Schinteie, G. [National Institute for Physics of Materials, Atomistilor 105 bis, P.O. Box MG-7, 077125 Bucharest-Magurele (Romania); Kuncser, V. [National Institute for Physics of Materials, Atomistilor 105 bis, P.O. Box MG-7, 077125 Bucharest-Magurele (Romania); Filoti, G. [National Institute for Physics of Materials, Atomistilor 105 bis, P.O. Box MG-7, 077125 Bucharest-Magurele (Romania)

2006-05-18

Magnesium-rich Mg-Ni-Fe intermetallic compounds have been prepared by two different routes: (a) short time ball milling of ribbons obtained by melt spinning; (b) long time ball milling of a mixture of MgH{sub 2}, Ni and Fe powders. The first type of samples displays an hydrogen desorption kinetics better than the second one. Pressure composition isotherm measurements exhibit for both type of samples two plateaux, the lower and wider corresponding to the MgH{sub 2} phase and the upper and shorter corresponding to the Mg{sub 2}NiH{sub 4} phase. The presence of the two types of hydrides is confirmed by X-ray diffraction analysis. Moessbauer spectroscopy shows that in melt spun and subsequently milled samples iron is mainly in a disordered structure and segregates after hydrogenation, while in directly milled powders remains mainly unalloyed. After multiple hydrogen absorption/desorption cycles the main part of iron is in metallic state in samples of both types, those of first type preserving better hydrogen desorption kinetics.

IMS Application Developer's Handbook Creating and Deploying Innovative IMS Applications

CERN Document Server

Noldus, Rogier; Mulligan, Catherine; Fikouras, Ioannis; Ryde, Anders; Stille, Mats

2011-01-01

IMS Application Developer Handbook will give a hands-on view of exactly what needs to be done by IMS application developers to write an application and take it "live" on an operator's network. It will offer practical guidance on building innovative applications using the features and capabilities of the IMS network, show how the rapidly changing development environment is impacting on the business models employed in the industry and how existing network solutions can be moved towards IMS. The book will also elaborate on how IMS applies basic VoIP principles and techniques to realise a true mul

Synthesis and Characterization of Solution and Melt Processible Poly(Acrylonitrile-Co-Methyl Acrylate) Statistical Copolymers

Science.gov (United States)

Pisipati, Padmapriya

Polyacrylonitrile (PAN) and its copolymers are used in a wide variety of applications ranging from textiles to purification membranes, packaging material and carbon fiber precursors. High performance polyacrylonitrile copolymer fiber is the most dominant precursor for carbon fibers. Synthesis of very high molecular weight poly(acrylonitrile-co-methyl acrylate) copolymers with weight average molecular weights of at least 1.7 million g/mole were synthesized on a laboratory scale using low temperature, emulsion copolymerization in a closed pressure reactor. Single filaments were spun via hybrid dry-jet gel solution spinning. These very high molecular weight copolymers produced precursor fibers with tensile strengths averaging 954 MPa with an elastic modulus of 15.9 GPa (N = 296). The small filament diameters were approximately 5 im. Results indicated that the low filament diameter that was achieved with a high draw ratio, combined with the hybrid dry-jet gel spinning process lead to an exponential enhancement of the tensile properties of these fibers. Carbon fibers for polymer matrix composites are currently derived from polyacrylonitrile copolymer fiber precursors where solution spinning accounts for ˜40 % of the total fiber production cost. To expand carbon fiber applications into the automotive industry, the cost of the carbon fiber needs to be reduced from 8 to ˜3-5. In order to develop an alternative melt processing route several benign plasticizers have been investigated. A low temperature, persulfate-metabisulfite initiated emulsion copolymerization was developed to synthesize poly(acrylonitrile-co-methyl acrylate) copolymers with acrylonitrile contents between 91-96 wt% with a molecular weight range of 100-200 kg/mol. This method was designed for a potential industrial scale up. Furthermore, water was investigated as a potential melting point depressant for these copolymers. Twenty-five wt% water lead to a decrease in the Tm of a 93/7 wt/wt % poly

Hydrogen absorption study of Ti-based alloys performed by melt-spinning

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, R.M.; Lemus, L.F.; Santos, D.S. dos, E-mail: rafaella@metalmat.ufrj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (PEMM/COPPEP/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Metalurgica e de Materiais

2013-11-01

The hydrogen absorption and desorption of Ti{sub 53}Zr{sub 27}Ni{sub 20} icosahedral quasicrystal (ICQ) and Ti{sub 50}Ni{sub 50} shape memory alloy (SMA) melt-spun ribbons was studied. Samples were exposed to hydrogen gas at 623 K and 4 MPa for 1000 minutes. The total capacity of hydrogen obtained for Ti{sub 53}Zr{sub 27}Ni{sub 20} and Ti{sub 50}Ni{sub 50} was 3.2 and 2.4 wt. % respectively. The Thermal Desorption Spectrometry (TDS) of the hydrogenated alloys shows that both alloys start to desorb hydrogen around 750 K. X-ray diffraction (XRD) patterns, performed after hydrogenation, indicate a complete amorphization of the Ti{sub 53}Zr{sub 27}Ni{sub 20} i-phase alloy, while the Ti{sub 50}Ni{sub 50} alloy remained crystalline after hydride formation. (author)

Structural and electrical studies on sol-gel derived spun TiO2 thin films

International Nuclear Information System (INIS)

Hassan, A K; Chaure, N B; Ray, A K; Nabok, A V; Habesch, S

2003-01-01

Titanium dioxide thin films were prepared by spin coating of sol precursor onto microscopic glass slides, silicon and indium tin oxide (ITO) coated glass substrates. Spin speed was varied between 1000 and 6000 rpm. From the morphological analysis, it is found that thin films spun with speed ω≤4000 rpm assume higher ordered structure than those spun at a speed higher than 4000 rpm. Conduction at low voltages is believed to be variable range hopping at temperatures T a = 0.46 eV below the conduction band edge becomes dominant at temperatures higher than 220 K. At high field charge transport is due to trap-controlled space charge limited mechanism. Traps with a density N t ∼1x10 22 m -3 are thought to be situated at energy level E t 0.3 eV below the conduction band and are associated with film nonstoichiometry and interface states

I'm a Map, I'm a Green Tree

Science.gov (United States)

Anderson, Daniel

2010-01-01

I'm talking about the ways we represent ourselves and our world. I've put some thoughts on the topic together here--a gathering that enacts new media creating and takes up conceptual layers like metaphors, models, and composing. The primary sources are videos from the Get a Mac campaign, aka I'm a Mac; I'm a PC ads. Posthuman concepts blending…

Coercivity and nanostructure of melt-spun Ti-Fe-Co-B-based alloys

Directory of Open Access Journals (Sweden)

W. Y. Zhang

2016-05-01

Full Text Available Nanocrystalline Ti-Fe-Co-B-based alloys, prepared by melt spinning and subsequent annealing, have been characterized structurally and magnetically. X-ray diffraction and thermomagnetic measurements show that the ribbons consist of tetragonal Ti3(Fe,Co5B2, FeCo-rich bcc, and NiAl-rich L21 phases; Ti3(Fe,Co5B2, is a new substitutional alloy series whose end members Ti3Co5B2 and Ti3Fe5B2 have never been investigated magnetically and may not even exist, respectively. Two compositions are considered, namely Ti11+xFe37.5-0.5xCo37.5−0.5xB14 (x = 0, 4 and alnico-like Ti11Fe26Co26Ni10Al11Cu2B14, the latter also containing an L21-type alloy. The volume fraction of the Ti3(Fe,Co5B2 phase increases with x, which leads to a coercivity increase from 221 Oe for x = 0 to 452 Oe for x = 4. Since the grains are nearly equiaxed, there is little or no shape anisotropy, and the coercivity is largely due to the magnetocrystalline anisotropy of the tetragonal Ti3(Fe,Co5B2 phase. The alloy containing Ni, Al, and Cu exhibits a magnetization of 10.6 kG and a remanence ratio of 0.59. Our results indicate that magnetocrystalline anisotropy can be introduced in alnico-like magnets, adding to shape anisotropy that may be induced by field annealing.

Influence of porosity and pore shape on structural, mechanical and biological properties of poly ϵ-caprolactone electro-spun fibrous scaffolds.

Science.gov (United States)

Fuller, Kieran P; Gaspar, Diana; Delgado, Luis M; Pandit, Abhay; Zeugolis, Dimitrios I

2016-05-01

Electro-spun scaffolds are utilized in a diverse spectrum of clinical targets, with an ever-increasing quantity of work progressing to clinical studies and commercialization. The limited number of conformations in which the scaffolds can be fabricated hampers their wide acceptance in clinical practice. Herein, we assessed a single-strep fabrication process for predesigned electro-spun scaffold preparation and the ramifications of the introduction of porosity (0, 30, 50, 70%) and pore shape (circle, rhomboid, square) on structural, mechanical (tensile and ball burst) and biological (dermal fibroblast and THP-1) properties. The collector design did not affect the fibrous nature of the scaffold. Modulation of the porosity and pore shape offered control over the mechanical properties of the scaffolds. Neither the porosity nor the pore shape affected cellular (dermal fibroblast and THP-1) response. Overall, herein we provide evidence that electro-spun scaffolds of controlled architecture can be fabricated with fibrous fidelity, adequate mechanical properties and acceptable cytocompatibility for a diverse range of clinical targets.

An analytical electron microscopy characterization of melt-spun iron/rare-earth/boron magnetic materials

International Nuclear Information System (INIS)

Dickenson, R.C.; Lawless, K.R.; Hadjipanayis, G.C.

1986-01-01

Iron/rare-earth/boron permanent magnet materials have recently been developed to reduce the need for the strategic element cobalt, which was previously the primary component of high-energy magnets. These materials are generally produced by annealing rapidly solidified ribbons or by conventional powder metallurgy techniques. This paper reports results from an analytical electron microscopy characterization undertaken to establish the relationship between the magnetic properties and the microstructure of two iron/rare-earth/boron (Fe/RE/B) alloys. Ribbons of Fe 75 Pr 15 B 10 and Fe 77 Tb 15 B 8 were produced by melt-spinning. To obtain optimum magnetic properties, both alloys were then annealed at 700 0 C, the FePrB ribbons for 6 minutes and the FeTbB ribbons for 90 minutes. Foils for transmission electron microscopy were prepared by ion-milling the ribbons on a cold stage and examined using a Philips 400T TEM/STEM equipped with an energy dispersive x-ray unit

Influence of micro-additions of bismuth on structures, mechanical and electrical transport properties of rapidly solidified Sn-3.5% Ag Alloy from melt

International Nuclear Information System (INIS)

El Bahay, M.M.; Mady, H.A.

2005-01-01

The present study was undertaken to investigate the influence of the Bi addition in the Sn-3.5 Ag rapidly solidified binary system for use as a Pb-free solder. The resulting properties of the binary system were extended to the Sn based ternary systems Sn 9 6.5-X Ag 3 .5 Bi x (0≤ X ≤ 2.5) solder. The structure and electrical resistivity of rapidly solidified (melt spun) alloys have been investigated. With the addition of up to 2.5 mass % Bi, the melting temperature decreases from 221.1 to 214.8 degree C. Wetting contact angle of the six alloys on Cu Zn 3 0 substrate are carried out at 573 K. Microhardness evaluations were also performed on the Sn-Ag-Bi alloys. The measured values and other researcher's results were compared with the calculated data

Hardness and microstructural characteristics of rapidly solidified Al-8-16 wt.%Si alloys

International Nuclear Information System (INIS)

Uzun, O.; Karaaslan, T.; Gogebakan, M.; Keskin, M.

2004-01-01

Al-Si alloys with nominal composition of Al-8 wt.%Si, Al-12 wt.%Si, and Al-16 wt.%Si were rapidly solidified by using melt-spinning technique to examine the influence of the cooling rate/conditions on microstructure and mechanical properties. The microstructures of the rapidly solidified ribbons and ingot samples were investigated by the optical microscopy, electron microscopy and X-ray diffraction (XRD) techniques. The results showed that the structures of all melt-spun ribbons were completely composed of finely dispersed α-Al and eutectic Si phase, and primary silicon was not observed. The XRD analysis indicated that the solubility of Si in the α-Al matrix was greatly increased with rapid solidification. Additionally, mechanical properties of both conventionally cast (ingot) and melt-spun ribbons were examined by using Vickers indenter for one applied load (0.098 N). The hardness values of the melt-spun ribbons were about three times higher than those of ingot counterparts. The high hardness of the rapidly solidified state can be attributed to the supersaturated solid solutions. Besides, hardness values with different applied loads were measured for melt-spun ribbons. The results indicated that Vickers hardness values (H v ) of the ribbons depended on the applied load. Applying the concept of Hays-Kendall, the load independent hardness values were calculated as 694.0, 982.8 and 1186.8 MN/m 2 for Al-8 wt.%Si, Al-12 wt.%Si and Al-16 wt.%Si, respectively

HRTEM characterization of melt-spun Al-Si-Cu-Mg alloys solidified at different rates

International Nuclear Information System (INIS)

Alfonso, Ismeli; Maldonado, Cuauhtemoc; Medina, Ariosto; Gonzalez, Gonzalo; Bejar, Luis

2006-01-01

Six quaternary alloys Al-6Si-3Cu-xMg (x = 0.59, 3.80 and 6.78 wt.%) were produced by melt spinning using two different tangential speeds of the copper wheel (30 and 45 ms -1 ), and characterized using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and microhardness. At 30 ms -1 , XRD and TEM investigations revealed the presence of Al 2 Cu (θ) for the alloy with 0.59%Mg and Al 5 Cu 2 Mg 8 Si 6 (Q) for the alloys with 3.80 and 6.78%Mg. The increase in microhardness of the alloys with higher Mg content is attributed to the presence of nanosized a-Al particles and a higher content of Q nanoparticles. At 45 ms -1 the alloying element content in solid solution is increased due to the fact that the quantity of free second phases (θ and Q nanoparticles) has decreased. For this rotation speed, amorphous regions of α -Al were observed, increasing microhardness compared to the 30 ms -1 ribbons

Linear Transformation of the Polarization Modes in Coiled Optical Spun-Fibers with Strong Unperturbed Linear Birefringence. I. Nonresonant Transformation

Science.gov (United States)

Malykin, G. B.; Pozdnyakova, V. I.

2018-03-01

A linear transformation of orthogonal polarization modes in coiled optical spun-fibers with strong unperturbed linear birefringence, which causes the emergence of the dependences of the integrated elliptical birefringence and the ellipticity and azimuth of the major axis of the ellipse, as well as the polarization state of radiation (PSR), on the length of optical fiber has been considered. Optical spun-fibers are subjected to a strong mechanical twisting, which is frozen into the structure of the optical fiber upon cooling, in the process of being drawn out from the workpiece. Since the values of the local polarization parameters of coiled spunwaveguides vary according to a rather complex law, the calculations were carried out by numerical modeling of the parameters of the Jones matrices. Since the rotation speed of the axes of the birefringence is constant on a relatively short segment of a coiled optical spun-fiber in the accompanying torsion (helical) coordinate system, the so-called "Ginzburg helical polarization modes" (GHPMs)—two mutually orthogonal ellipses with the opposite directions of traversal, the axis of which rotate relative to the fixed coordinate system uniformly and unidirectionally—are approximately the local normal polarization modes of such optical fiber. It has been shown that, despite the fact that the unperturbed linear birefringence of the spun-fibers significantly exceeds the linear birefringence, which is caused by the winding on a coil, the integral birefringence of an extended segment of such a fiber coincides in order of magnitude with the linear birefringence, which is caused by the winding on the coil, and the integral polarization modes tend asymptotically to circular ones. It has been also shown that the values of the circular birefringence of twisted single-mode fibers, which were calculated in a nonrotating and torsion helical coordinate systems, differ significantly. It has been shown that the polarization phenomena occur

Wet-Spun Biofiber for Torsional Artificial Muscles.

Science.gov (United States)

Mirabedini, Azadeh; Aziz, Shazed; Spinks, Geoffrey M; Foroughi, Javad

2017-12-01

The demands for new types of artificial muscles continue to grow and novel approaches are being enabled by the advent of new materials and novel fabrication strategies. Self-powered actuators have attracted significant attention due to their ability to be driven by elements in the ambient environment such as moisture. In this study, we demonstrate the use of twisted and coiled wet-spun hygroscopic chitosan fibers to achieve a novel torsional artificial muscle. The coiled fibers exhibited significant torsional actuation where the free end of the coiled fiber rotated up to 1155 degrees per mm of coil length when hydrated. This value is 96%, 362%, and 2210% higher than twisted graphene fiber, carbon nanotube torsional actuators, and coiled nylon muscles, respectively. A model based on a single helix was used to evaluate the torsional actuation behavior of these coiled chitosan fibers.

Organisationsprobleme im Ökomarketing

OpenAIRE

Dienel, Wolfram

2000-01-01

Organisationsprobleme im Ökomarketing - eine transaktionskostentheoretische Analyse im Absatzkanal konventioneller Lebensmittelhandel Die im Vergleich zum großen Nachfragepotential zögerliche Entwicklung des Ökomarkts in Deutschland ist auf Organisationsprobleme zurückzuführen. Die Organisationsprobleme behindern insbesondere die großskalige Ökomarkterschließung über die konventionellen Supermarktketten, erschweren aber auch die Effizienzsteigerung im kleiner strukturierten alternativen N...

The further development and evaluation of an automatic dismantler of short staple ring-spun yarns

CSIR Research Space (South Africa)

Fassihi, A

2014-07-01

Full Text Available Information System (AFIS) single fiber length tests, the fibers from automatically dismantled ring-spun cotton yarns are very similar in their properties to those dismantled by hand (manually). It was also found that, at a speed of 2 m/min, the yarn dismantler...

Mutual interaction between high and low stereo-regularity components for crystallization and melting behaviors of polypropylene blend fibers

Science.gov (United States)

Kawai, Kouya; Kohri, Youhei; Takarada, Wataru; Takebe, Tomoaki; Kanai, Toshitaka; Kikutani, Takeshi

2016-03-01

Crystallization and melting behaviors of blend fibers of two types of polypropylene (PP), i.e. high stereo-regularity/high molecular weight PP (HPP) and low stereo-regularity/low molecular weight PP (LPP), was investigated. Blend fibers consisting of various HPP/LPP compositions were prepared through the melt spinning process. Differential scanning calorimetry (DSC), temperature modulated DSC (TMDSC) and wide-angle X-ray diffraction (WAXD) analysis were applied for clarifying the crystallization and melting behaviors of individual components. In the DSC measurement of blend fibers with high LPP composition, continuous endothermic heat was detected between the melting peaks of LPP at around 40 °C and that of HPP at around 160 °C. Such endothermic heat was more distinct for the blend fibers with higher LPP composition indicating that the melting of LPP in the heating process was hindered because of the presence of HPP crystals. On the other hand, heat of crystallization was detected at around 90 °C in the case of blend fibers with LPP content of 30 to 70 wt%, indicating that the crystallization of HPP component was taking place during the heating of as-spun blend fibers in the DSC measurement. Through the TMDSC analysis, re-organization of the crystalline structure through the simultaneous melting and re-crystallization was detected in the cases of HPP and blend fibers, whereas re-crystallization was not detected during the melting of LPP fibers. In the WAXD analysis during the heating of fibers, amount of a-form crystal was almost constant up to the melting in the case of single component HPP fibers, whereas there was a distinct increase of the intensity of crystalline reflections from around 100 °C, right after the melting of LPP in the case of blend fibers. These results suggested that the crystallization of HPP in the spinning process as well as during the conditioning process after spinning was hindered by the presence of LPP.

Mutual interaction between high and low stereo-regularity components for crystallization and melting behaviors of polypropylene blend fibers

International Nuclear Information System (INIS)

Kawai, Kouya; Takarada, Wataru; Kikutani, Takeshi; Kohri, Youhei; Takebe, Tomoaki; Kanai, Toshitaka

2016-01-01

Crystallization and melting behaviors of blend fibers of two types of polypropylene (PP), i.e. high stereo-regularity/high molecular weight PP (HPP) and low stereo-regularity/low molecular weight PP (LPP), was investigated. Blend fibers consisting of various HPP/LPP compositions were prepared through the melt spinning process. Differential scanning calorimetry (DSC), temperature modulated DSC (TMDSC) and wide-angle X-ray diffraction (WAXD) analysis were applied for clarifying the crystallization and melting behaviors of individual components. In the DSC measurement of blend fibers with high LPP composition, continuous endothermic heat was detected between the melting peaks of LPP at around 40 °C and that of HPP at around 160 °C. Such endothermic heat was more distinct for the blend fibers with higher LPP composition indicating that the melting of LPP in the heating process was hindered because of the presence of HPP crystals. On the other hand, heat of crystallization was detected at around 90 °C in the case of blend fibers with LPP content of 30 to 70 wt%, indicating that the crystallization of HPP component was taking place during the heating of as-spun blend fibers in the DSC measurement. Through the TMDSC analysis, re-organization of the crystalline structure through the simultaneous melting and re-crystallization was detected in the cases of HPP and blend fibers, whereas re-crystallization was not detected during the melting of LPP fibers. In the WAXD analysis during the heating of fibers, amount of a-form crystal was almost constant up to the melting in the case of single component HPP fibers, whereas there was a distinct increase of the intensity of crystalline reflections from around 100 °C, right after the melting of LPP in the case of blend fibers. These results suggested that the crystallization of HPP in the spinning process as well as during the conditioning process after spinning was hindered by the presence of LPP.

Mutual interaction between high and low stereo-regularity components for crystallization and melting behaviors of polypropylene blend fibers

Energy Technology Data Exchange (ETDEWEB)

Kawai, Kouya; Takarada, Wataru; Kikutani, Takeshi, E-mail: kikutani.t.aa@m.titech.ac.jp [Department of Organic and Polymeric Materials, Graduate School of Science and Engineering, Tokyo Institute of Technology, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8552 (Japan); Kohri, Youhei; Takebe, Tomoaki [Performance Materials Laboratories, Idemitsu Kosan Co.,Ltd. (Japan); Kanai, Toshitaka [KT Polymer (Japan)

2016-03-09

Crystallization and melting behaviors of blend fibers of two types of polypropylene (PP), i.e. high stereo-regularity/high molecular weight PP (HPP) and low stereo-regularity/low molecular weight PP (LPP), was investigated. Blend fibers consisting of various HPP/LPP compositions were prepared through the melt spinning process. Differential scanning calorimetry (DSC), temperature modulated DSC (TMDSC) and wide-angle X-ray diffraction (WAXD) analysis were applied for clarifying the crystallization and melting behaviors of individual components. In the DSC measurement of blend fibers with high LPP composition, continuous endothermic heat was detected between the melting peaks of LPP at around 40 °C and that of HPP at around 160 °C. Such endothermic heat was more distinct for the blend fibers with higher LPP composition indicating that the melting of LPP in the heating process was hindered because of the presence of HPP crystals. On the other hand, heat of crystallization was detected at around 90 °C in the case of blend fibers with LPP content of 30 to 70 wt%, indicating that the crystallization of HPP component was taking place during the heating of as-spun blend fibers in the DSC measurement. Through the TMDSC analysis, re-organization of the crystalline structure through the simultaneous melting and re-crystallization was detected in the cases of HPP and blend fibers, whereas re-crystallization was not detected during the melting of LPP fibers. In the WAXD analysis during the heating of fibers, amount of a-form crystal was almost constant up to the melting in the case of single component HPP fibers, whereas there was a distinct increase of the intensity of crystalline reflections from around 100 °C, right after the melting of LPP in the case of blend fibers. These results suggested that the crystallization of HPP in the spinning process as well as during the conditioning process after spinning was hindered by the presence of LPP.

Calculation of the mean differential group delay of periodically spun, randomly birefringent fibers

Science.gov (United States)

Galtarossa, Andrea; Griggio, Paola; Pizzinat, Anna; Palmieri, Luca

2002-05-01

Spinning is one of the most effective and well-known ways to reduce polarization mode dispersion of optical fibers. In spite of the popularity of spinning, a detailed theory of spin effects is still lacking. We report an analytical expression for the mean differential group delay of a randomly birefringent spun fiber. The result holds for any periodic spin function with a period shorter than the fiber's beat length.

Effect of solidification rate on the microstructure and microhardness of a melt-spun Al-8Si-1Sb alloy

International Nuclear Information System (INIS)

Karakoese, E.; Keskin, M.

2009-01-01

The properties of rapidly solidified hypoeutectic Al-8Si-1Sb alloy, produced by melt-spinning technique at a different solidification rates, were investigated using the X-ray diffraction (XRD), the optical microscopy (OM), the scanning electron microscopy (SEM) together with the energy dispersive spectroscopy (EDS), the differential scanning calorimetry (DSC) and the microhardness technique. The properties of rapidly solidified ribbons were then compared with those of the chill-casting alloy. The results show that rapid solidification has influence on the phase constitution of the hypoeutectic Al-8Si-1Sb alloy. The phases present in the hypoeutectic Al-8Si-1Sb ingot alloy were determined to be α-Al, fcc Si and intermetallic AlSb phases whereas only α-Al and fcc Si phases were identified in the melt-spinning alloy. The rapid solidification has a significant effect on the microstructure of the hypoeutectic Al-8Si-1Sb alloy. Particle size in the microstructure of the ribbons is too small to compare with particle size in the microstructure of the ingot alloy. Moreover, the significant change in hardness occurs that is attributed to changes in the microstructure.

Effect of solidification rate on the microstructure and microhardness of a melt-spun Al-8Si-1Sb alloy

Energy Technology Data Exchange (ETDEWEB)

Karakoese, E. [Erciyes University, Institute of Science, 38039 Kayseri (Turkey); Keskin, M. [Erciyes University, Institute of Science, 38039 Kayseri (Turkey); Erciyes University, Physics Department, 38039 Kayseri (Turkey)], E-mail: keskin@erciyes.edu.tr

2009-06-24

The properties of rapidly solidified hypoeutectic Al-8Si-1Sb alloy, produced by melt-spinning technique at a different solidification rates, were investigated using the X-ray diffraction (XRD), the optical microscopy (OM), the scanning electron microscopy (SEM) together with the energy dispersive spectroscopy (EDS), the differential scanning calorimetry (DSC) and the microhardness technique. The properties of rapidly solidified ribbons were then compared with those of the chill-casting alloy. The results show that rapid solidification has influence on the phase constitution of the hypoeutectic Al-8Si-1Sb alloy. The phases present in the hypoeutectic Al-8Si-1Sb ingot alloy were determined to be {alpha}-Al, fcc Si and intermetallic AlSb phases whereas only {alpha}-Al and fcc Si phases were identified in the melt-spinning alloy. The rapid solidification has a significant effect on the microstructure of the hypoeutectic Al-8Si-1Sb alloy. Particle size in the microstructure of the ribbons is too small to compare with particle size in the microstructure of the ingot alloy. Moreover, the significant change in hardness occurs that is attributed to changes in the microstructure.

Experimental studies on the nature of bonding of DNA/bipyridyl-(ethylenediamine)platinum(II) and DNA/netropsin complexes in solution and oriented wet-spun films

Science.gov (United States)

Marlowe, R. L.; Szabo, A.; Lee, S. A.; Rupprecht, A.

2002-03-01

The stability of complexes of NaDNA with bipyridyl-(ethylenediamine)platinum(II) (abbreviated [(bipy)Pt(en)]) and with netropsin has been studied using two techniques: (i) ultraviolet melting experiments were done on NaDNA/[(bipy)Pt(en)], showing that the [(bipy)Pt(en)] ligand stabilizes the DNA double helix structure; and (ii) swelling measurements (via optical microscopy) as a function of relative humidity were done on wet-spun oriented films of NaDNA/[(bipy)Pt(en)] and of NaDNA/netropsin. The swelling data shows that an irreversible transition of the films occurs at high relative humidity, first for the NaDNA/netropsin, then for pure NaDNA, and lastly for the NaDNA/[(bipy)Pt(en)]. These results are indicative that the [(bipy)Pt(en)] complex stabilizes the intermolecular bonds which mediate the film swelling characteristics. A model is suggested for the binding of [(bipy)Pt(en)] to DNA to explain why the swelling experiments show this ligand as increasing the intermolecular bond strength between the DNA double helices, while netropsin decreases this degree of stabilization.

Characterization of nanocomposite NdFeB permanent magnetic materials

International Nuclear Information System (INIS)

Mat Husin Salleh; Hussain, P.; Mohammad, M.; Abd Aziz Mohamed

2005-01-01

The following topics were discussed: Introduction to NdFeB magnet, grain size measurement using XRD (X-ray diffraction), FESEM , TEM (Transmission Electron Microscopy) and SANS (Small-angle Neutron Scattering). The objective of the project are to analyze the structure of nano-crystallite formed in the melt spun ribbons after annealing by XRD, FESEM,TEM and SANS, to study the magnetic properties of nano-composite NdFeB melt spun ribbons and their bonded magnet and possible usage in small motor to replace the conventional NdFeB bonded magnet

Study of the high temperature characteristics of hydrogen storage alloys

CERN Document Server

Rong, Li; Shaoxiong, Zhou; Yan, Qi; 10.1016/j.jallcom.2004.07.006

2005-01-01

In this work, the phase structure of as-cast and melt-spun (MmY)/sub 1/(NiCoMnAl)/sub 5/ alloys (the content of yttrium is 0-2.5wt.%) and their electrochemical properties were studied with regard to discharge capacity at different temperatures (30-80 degrees C) and cycling life at 30 degrees C. It is found that the substitution of yttrium increase the electrochemical capacity of the compounds and decrease the difference in capacity between as-cast and as-quenched compounds at 30 degrees C. When increasing the yttrium concentration from 0 to 2.5wt.%, the cycling life of both the as-cast and the melt- spun compounds deteriorated, although the latter have a slightly longer cycle life than the former. The remarkable feature of the alloys obtained by yttrium substitution is the improvement of the high temperature electrochemical properties. It shows that the stability of the hydrides is increased. Compared with the as-cast alloys, the melt-spun ribbons have higher electrochemical charge /discharge capacity in the ...

On the synthesis and characterization of some new AB{sub 5} type MmNi{sub 4.3}Al{sub 0.3},Mn{sub 0.4}, LaNi{sub 5-{chi}}Si{sub {chi}} ({chi} = 0.1, 0.3, 0.5) and Mg-{chi} wt% CFMmNi{sub 5}-y wt% Si hydrogen storage materials

Energy Technology Data Exchange (ETDEWEB)

Srivistava, S.; Sai Raman, S.S.; Singh, B.K.; Srivistava, O.N. [Banaras Hindu Univ., Varanasi (India). Dept. of Physics

2000-05-01

The viability and feasibility of Hydrogen Energy becoming the clean alternative to Fossil Fuel Energy through replacement of 'Fossil Fuel' with 'Hydrogen' (the Green Fuel) is inextricably interlinked with development of 'Hydrogen Storage Systems'. Out of the high pressure gaseous hydrogen, liquid hydrogen, storage in glass microspheres, activated carbon, zeolites, hydrogen rich liquids and solid state hydrides, the last option is of implicit importance. Out of the AB (e.g., FeTi, storage capacity -- 1.75 wt%), AB{sub 2} or A{sub 2}B (Mg{sub 2}Ni -- 3.8 wt%), AB{sub 5} (LaNi{sub 5}, MmN{sub 5} -- 1.5 wt%) and K{sub 2} PtCl{sub 6} type (Mg{sub 2}FeH{sub 6} -- 5.2 wt%); the AB{sub 5} type holds potential promise due to easy activation, tolerance to impurities of charging H{sub 2} gas and avid amenability towards material tailoring for improved and better hydrogenation characteristics. We have carried out synthesis, characterization of several of the AB{sub 5} type storage materials. The present paper is aimed at describing and discussing some of our more recent efforts in regard to this. In the present study the hydrogen storage material (MH) has been synthesized through normal casting (Radio Frequency (RF) induction melting) and melt-spinning techniques. The improvements in basic alloys LaNi{sub 5}/MmNi{sub 5} have been studied through structural, microstructural and hydrogenation characteristics. The main features revealed by XRD characterizations are the existence of the free Ni and Si together with AB{sub 5} material in melt-spun alloy of LaNi{sub 5-{chi}}Si{sub {chi}}. These free Ni and Si were found to disappear, giving rise to a singular material after hydrogenation. Also in melt-spun alloy growth has taken place in a direction perpendicular to the c-axis. Melt-spun version was found to be superior over bulk version in regard to kinetics and activation process. For MmNi{sub 4.3}AlO{sub 3}Mn{sub 0.4} alloy, melt-spun version has

Effect of Al substitution for B on magnetic and structural properties of Co-based melt-spun ribbons

International Nuclear Information System (INIS)

Sepehri Amin, H.; Gholamipour, R.; Shahri, F.; Mohammadi, A.

2008-01-01

This paper reports structural and magnetic properties of rapidly quenched Co 64 Fe 4 Ni 2 B 19-x Si 8 Cr 3 Al x (x=0, 1, 2, 3) amorphous ribbons prepared by the single roller melt spinning process. Thermal analysis of the ribbons shows that the replacement of B by Al causes a decrease in the crystallization temperature. Structural studies of the samples have been carried out by transmission electron microscopy and X-ray diffraction. With optimum amount of Al in the alloy, the as-cast material has better soft magnetic properties. The highest maximum permeability (3.55x10 5 ), saturation magnetization (523.7 mT) and the lowest coercivity (0.8174 A/m) were obtained in the sample with x=2

A Review on the Fabrication of Electro spun Polymer Electrolyte Membrane for Direct Methanol Fuel Cell

International Nuclear Information System (INIS)

Junoh, H.; Jaafar, J.; Norddin, M.N.A.M.; Ismail, A.F.; Othman, M.H.D.; Rahman, M.A.; Yusof, N.; Salleh, W.N.W.; Junoh, H.; Jaafar, J.; Norddin, M.N.A.M.; Ismail, A.F.; Othman, M.H.D.; Rahman, M.A.; Yusof, N.; Salleh, W.N.W.; Hamid Ilbeygi, H.

2014-01-01

Proton exchange membrane (PEM) is an electrolyte which behaves as important indicator for fuel cell’s performance. Research and development (R and D) on fabrication of desirable PEM have burgeoned year by year, especially for direct methanol fuel cell (DMFC). However, most of the R and Ds only focus on the parent polymer electrolyte rather than polymer inorganic composites. This might be due to the difficulties faced in producing good dispersion of inorganic filler within the polymer matrix, which would consequently reduce the DMFC’s performance. Electro spinning is a promising technique to cater for this arising problem owing to its more widespread dispersion of inorganic filler within the polymer matrix, which can reduce the size of the filler up to nano scale. There has been a huge development on fabricating electrolyte nano composite membrane, regardless of the effect of electro spun nano composite membrane on the fuel cell’s performance. In this present paper, issues regarding the R and D on electro spun sulfonated poly (ether ether ketone) (SPEEK)/inorganic nano composite fiber are addressed.

Inductive Monitoring System (IMS)

Data.gov (United States)

National Aeronautics and Space Administration — IMS: Inductive Monitoring System The Inductive Monitoring System (IMS) is a tool that uses a data mining technique called clustering to extract models of normal...

Integrating IMS LD and IMS QTIv2 using CopperCore Service Integration

NARCIS (Netherlands)

Vogten, Hubert

2006-01-01

Vogten, H. (2006). Integrating IMS LD and IMS QTIv2 using CopperCore Service Integration. Presentation at International Workshop in Learning Networks for Lifelong Competence Development. March, 30-31, 2006. Sofia, Bulgaria: TENCompetence Conference. Retrieved June 30th, 2006, from

Air-spun PLA nanofibers modified with reductively sheddable hydrophilic surfaces for vascular tissue engineering: synthesis and surface modification.

Science.gov (United States)

Ko, Na Re; Sabbatier, Gad; Cunningham, Alexander; Laroche, Gaétan; Oh, Jung Kwon

2014-02-01

Polylactide (PLA) is a class of promising biomaterials that hold great promise for various biological and biomedical applications, particularly in the field of vascular tissue engineering where it can be used as a fibrous mesh to coat the inside of vascular prostheses. However, its hydrophobic surface providing nonspecific interactions and its limited ability to further modifications are challenges that need to be overcome. Here, the development of new air-spun PLA nanofibers modified with hydrophilic surfaces exhibiting reduction response is reported. Surface-initiated atom transfer radical polymerization allows for grafting pendant oligo(ethylene oxide)-containing polymethacrylate (POEOMA) from PLA air-spun fibers labeled with disulfide linkages. The resulting PLA-ss-POEOMA fibers exhibit enhanced thermal stability and improved surface properties, as well as thiol-responsive shedding of hydrophilic POEOMA by the cleavage of its disulfide linkages in response to reductive reactions, thus tuning the surface properties. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Solid-State Densification of Spun-Cast Self-Assembled Monolayers for Use in Ultra-Thin Hybrid Dielectrics.

Science.gov (United States)

Hutchins, Daniel O; Acton, Orb; Weidner, Tobias; Cernetic, Nathan; Baio, Joe E; Castner, David G; Ma, Hong; Jen, Alex K-Y

2012-11-15

Ultra-thin self-assembled monolayer (SAM)-oxide hybrid dielectrics have gained significant interest for their application in low-voltage organic thin film transistors (OTFTs). A [8-(11-phenoxy-undecyloxy)-octyl]phosphonic acid (PhO-19-PA) SAM on ultrathin AlO x (2.5 nm) has been developed to significantly enhance the dielectric performance of inorganic oxides through reduction of leakage current while maintaining similar capacitance to the underlying oxide structure. Rapid processing of this SAM in ambient conditions is achieved by spin coating, however, as-cast monolayer density is not sufficient for dielectric applications. Thermal annealing of a bulk spun-cast PhO-19-PA molecular film is explored as a mechanism for SAM densification. SAM density, or surface coverage, and order are examined as a function of annealing temperature. These SAM characteristics are probed through atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and near edge X-ray absorption fine structure spectroscopy (NEXAFS). It is found that at temperatures sufficient to melt the as-cast bulk molecular film, SAM densification is achieved; leading to a rapid processing technique for high performance SAM-oxide hybrid dielectric systems utilizing a single wet processing step. To demonstrate low-voltage devices based on this hybrid dielectric (with leakage current density of 7.7×10 -8 A cm -2 and capacitance density of 0.62 µF cm -2 at 3 V), pentacene thin-film transistors (OTFTs) are fabricated and yield sub 2 V operation and charge carrier mobilites of up to 1.1 cm 2 V -1 s -1 .

Influence of HMW tail chains on the structural evolution of HDPE induced by second melt penetration.

Science.gov (United States)

Zhu, Chun-Xia; Xia, Xiao-Chao; Huang, Yan-Hao; Xie, Dan-Dan; Chen, Rui; Yang, Ming-Bo

2017-07-21

It is widely accepted that the role of the high molecular weight (HMW) component is cooperative in shear-induced crystallization, owing to entanglements among long chains. However, this paper demonstrates that the HMW component has a novel effect on structural evolution during the process of multi-melt multi-injection molding (M 3 IM), organized as follows. First, the appropriate HDPE system with an incremental concentration of HMW tails was established. Second, the crystalline morphologies and orientation behaviors of the M 3 IM samples were characterized using a combination of scanning electron microscopy (SEM) and two-dimensional small angle X-ray scattering (2D-SAXS), and these suggested that the amount of shish-kebabs was not monotonically promoted with an increasing content of HMW tails but tended to reduce at a certain value. Third, in order to explain this phenomenon, the special temperature and shear profiles of M 3 IM were depicted subsequently, and finally the mechanism of hierarchical structure formation with the influence of various amounts of HMW tail chains was discussed, based on the classical rheological viewpoint.

Comparison of directly compressed vitamin B12 tablets prepared from micronized rotary-spun microfibers and cast films.

Science.gov (United States)

Sebe, István; Bodai, Zsolt; Eke, Zsuzsanna; Kállai-Szabó, Barnabás; Szabó, Péter; Zelkó, Romána

2015-01-01

Fiber-based dosage forms are potential alternatives of conventional dosage forms from the point of the improved extent and rate of drug dissolution. Rotary-spun polymer fibers and cast films were prepared and micronized in order to direct compress after homogenization with tabletting excipients. Particle size distribution of powder mixtures of micronized fibers and films homogenized with tabletting excipients were determined by laser scattering particle size distribution analyzer. Powder rheological behavior of the mixtures containing micronized fibers and cast films was also compared. Positron annihilation lifetime spectroscopy was applied for the microstructural characterization of micronized fibers and films. The water-soluble vitamin B12 release from the compressed tablets was determined. It was confirmed that the rotary spinning method resulted in homogeneous supramolecularly ordered powder mixture, which was successfully compressed after homogenization with conventional tabletting excipients. The obtained directly compressed tablets showed uniform drug release of low variations. The results highlight the novel application of micronized rotary-spun fibers as intermediate for further processing reserving the original favorable powder characteristics of fibrous systems.

TEM studies of nanostructure in melt-spun Mg-Ni-La alloy manifesting enhanced hydrogen desorbing kinetics

International Nuclear Information System (INIS)

Tanaka, K.; Miwa, T.; Sasaki, K.; Kuroda, K.

2009-01-01

The hydrogen storage properties of a magnesium-rich Mg-Ni-La alloy prepared by melt-spinning are significantly improved by nanostructure formation during crystallization and activation. It can absorb and desorb ∼5 wt% hydrogen at temperatures as low as 200 deg. C in moderate time periods. Transmission electron microscopic (TEM) studies on this alloy indicate that the nanostructure, consisting of LaH 3 and Mg 2 NiH 4 nano-particles dispersed homogeneously in MgH 2 matrices after hydrogenation, is rather stable at temperatures below 300 deg. C but undergoes coarsening and segregation of these particles and matrices above ∼400 deg. C. These structural changes have been confirmed by electron energy-loss spectroscopic (EELS) imaging as well as high-resolution TEM techniques. A new EELS peak associated with a plasmon excitation in the MgH 2 phase (H-plasmon) is found for the first time in this study. By imaging the H-plasmon peak, the hydrogen distribution in the alloy has been clearly visualized. We have succeeded in observing the hydrogen desorption process at ∼400 deg. C in-situ in the microscope using this EELS imaging technique.

Resilience in IMS

DEFF Research Database (Denmark)

Kamyod, Chayapol; Nielsen, Rasmus Hjorth; Prasad, Neeli R.

2012-01-01

) and supporting always on services. Therefore, not only Quality of Service (QoS) but also resilience is required. In this paper, we attempt to evaluate and analyze end-to-end reliability of the IMS system using a model proposed as a combination of Reliability Block Diagram (RBD) and Markov Reward Models (MRMs......Reliability evaluation of systems has been widely researched for improving system resilience especially in designing processes of a complex system. The convergence of different access networks is possible via IP Multimedia Subsystem (IMS) for development toward Next Generation Networks (NGNs......). The resilience of the IMS architecture is studied by applying 1:1 redundancy at different communication scenarios between end users within and across communication domains. The model analysis provides useful reliability characteristics of the system and can be further applied for system design processes....

Delegation und Kooperation im Gesundheitswesen

OpenAIRE

Rosenau, Henning

2010-01-01

Delegation und Kooperation im Gesundheitswesen. - In: Tıpta işbirliği ve hukuksal sorunlar = Delegation und Kooperation im Gesundheitswesen / ed.: Hakan Hakeri ... - Samsun : Adalet, 2010. - S. 7-18

Innovationsmanagement im Marketing: Anleitung zur Innovations-Sensibilisierung und deren Umsetzung im Rahmen der Neuen Lernkultur

OpenAIRE

Mangisch, Christian; Blatter, Martin

2009-01-01

Der Kurs “Innovationsmanagement im Marketing“ vermittelt den Teilnehmenden Wissen zum Innovationsmanagement, zum innovativen Team und zu innovativen Marketing Trends. Diese Kurse sind online auf dem folgenden Link www.ritzycampus.ch zu finden. Die Teilnehmer müssen für den Online-Kurs keine speziellen Kenntnisse oder Voraussetzungen mitbringen. Diese Online-Kurse im Fach Marketing sind an ein breites Publikum gerichtet. Sie ermöglichen den Studierenden im Eigenstudium die Grundlagen der Theme...

Δim-lacunary statistical convergence of order α

Science.gov (United States)

Altınok, Hıfsı; Et, Mikail; Işık, Mahmut

2018-01-01

The purpose of this work is to introduce the concepts of Δim-lacunary statistical convergence of order α and lacunary strongly (Δim,p )-convergence of order α. We establish some connections between lacunary strongly (Δim,p )-convergence of order α and Δim-lacunary statistical convergence of order α. It is shown that if a sequence is lacunary strongly (Δim,p )-summable of order α then it is Δim-lacunary statistically convergent of order α.

[Kriegsland im Osten Eroberung, Kolonisierung und Militärherrschaft im Ersten Weltkrieg] / Markus Pöhlmann

Index Scriptorium Estoniae

Pöhlmann, Markus

2003-01-01

Rets.: Vejas Gabriel Liulevicius. Kriegsland im Osten Eroberung, Kolonisierung und Militärherrschaft im Ersten Weltkrieg. Aus dem Amerikanischen von Jürgen Bauer, Edith Nerke und Fee Engemann. Hamburg : 2002

CopperCore Service Integration, Integrating IMS Learning Design and IMS Question and Test Interoperability

NARCIS (Netherlands)

Vogten, Hubert; Martens, Harrie; Nadolski, Rob; Tattersall, Colin; Van Rosmalen, Peter; Koper, Rob

2006-01-01

Vogten, H., Martens, H., Nadolski, R., Tattersall, C., Rosmalen, van, P., Koper, R., (2006). CopperCore Service Integration, Integrating IMS Learning Design and IMS Question and Test Interoperability. Proceedings of the 6th IEEE International Conference on Advanced Learning Technologies (pp.

Volatility study of [C1C1im][NTf2] and [C2C3im][NTf2] ionic liquids

International Nuclear Information System (INIS)

Rocha, Marisa A.A.; Ribeiro, Filipe M.S.; Schröder, Bernd; Coutinho, João A.P.; Santos, Luís M.N.B.F.

2014-01-01

Highlights: • Vapor pressures of [C 1 C 1 im][NTf 2 ] and [C 2 C 3 im][NTf 2 ] ionic liquids are reported. • [C 1 C 1 im][NTf 2 ] presents higher enthalpy and entropy of vaporization than expected. • The high volatility of [C 2 C 3 im][NTf 2 ] is a result from its asymmetric character. -- Abstract: Vapor pressures of 1,3-dimethylimidazolium bis(trifluoromethylsulfonyl)imide, ([C 1 C 1 im][NTf 2 ]) and 1-ethyl-3-propylimidazolium bis(trifluoromethylsulfonyl)imide, ([C 2 C 3 im][NTf 2 ]) ionic liquids were measured as a function of temperature using a Knudsen effusion apparatus combined with a quartz crystal microbalance. Enthalpies and entropies of vaporization were derived from the fitting of vapor pressure and temperature results to the Clarke and Glew equation. [C 1 C 1 im][NTf 2 ] presents a higher enthalpy and entropy of vaporization than the neighboring members of the series. The enthalpy of vaporization of [C 2 C 3 im][NTf 2 ] lies in between the asymmetric and symmetric ionic liquid series, reflecting a decrease in the electrostatic interactions due to a decrease of the charge accessibility between the ionic pairs when the methyl group is replaced by an ethyl group. The obtained higher volatility of [C 2 C 3 im][NTf 2 ] arises from its asymmetric character, leading to an higher entropic contribution that compensates the enthalpic penalty. The border conditions ([C 1 C 1 im][NTf 2 ], [C 2 C 1 im][NTf 2 ] and [C 2 C 2 im][NTf 2 ]), topology ([C 2 C 3 im][NTf 2 ]) and symmetry/asymmetry of the ILs effect were evaluated and rationalized based on a comparative analysis of the thermodynamic properties, enthalpies and entropies of vaporization

Application of Hadamard transform in IMS

International Nuclear Information System (INIS)

Sha Miaomiao; Liu Weihao; Chen Yong; Jiang Dazhen

2008-01-01

Hadamard transform can improve the SNR by increasing the ion duty cycle in IMS. In this paper, the ion spectral signals were processed by Hadamard transform based on the IMS detector hardware platform. The results showed that Hadamard transform can greatly improve the SNR of the IMS detector in contrast with traditional method. (authors)

Thread-like supercapacitors based on one-step spun nanocomposite yarns.

Science.gov (United States)

Meng, Qinghai; Wang, Kai; Guo, Wei; Fang, Jin; Wei, Zhixiang; She, Xilin

2014-08-13

Thread-like electronic devices have attracted great interest because of their potential applications in wearable electronics. To produce high-performance, thread-like supercapacitors, a mixture of stable dispersions of single-walled carbon nanotubes and conducting polyaniline nanowires are prepared. Then, the mixture is spun into flexible yarns with a polyvinyl alcohol outer sheath by a one-step spinning process. The composite yarns show excellent mechanical properties and high electrical conductivities after sufficient washing to remove surfactants. After applying a further coating layer of gel electrolyte, two flexible yarns are twisted together to form a thread-like supercapacitor. The supercapacitor based on these two yarns (SWCNTs and PAniNWs) possesses a much higher specific capacitance than that based only on pure SWCNTs yarns, making it an ideal energy-storage device for wearable electronics. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Petrological Geodynamics of Mantle Melting II. AlphaMELTS + Multiphase Flow: Dynamic Fractional Melting

Science.gov (United States)

Tirone, Massimiliano

2018-03-01

In this second installment of a series that aims to investigate the dynamic interaction between the composition and abundance of the solid mantle and its melt products, the classic interpretation of fractional melting is extended to account for the dynamic nature of the process. A multiphase numerical flow model is coupled with the program AlphaMELTS, which provides at the moment possibly the most accurate petrological description of melting based on thermodynamic principles. The conceptual idea of this study is based on a description of the melting process taking place along a 1-D vertical ideal column where chemical equilibrium is assumed to apply in two local sub-systems separately on some spatial and temporal scale. The solid mantle belongs to a local sub-system (ss1) that does not interact chemically with the melt reservoir which forms a second sub-system (ss2). The local melt products are transferred in the melt sub-system ss2 where the melt phase eventually can also crystallize into a different solid assemblage and will evolve dynamically. The main difference with the usual interpretation of fractional melting is that melt is not arbitrarily and instantaneously extracted from the mantle, but instead remains a dynamic component of the model, hence the process is named dynamic fractional melting (DFM). Some of the conditions that may affect the DFM model are investigated in this study, in particular the effect of temperature, mantle velocity at the boundary of the mantle column. A comparison is made with the dynamic equilibrium melting (DEM) model discussed in the first installment. The implications of assuming passive flow or active flow are also considered to some extent. Complete data files of most of the DFM simulations, four animations and two new DEM simulations (passive/active flow) are available following the instructions in the supplementary material.

E2eUberIM

DEFF Research Database (Denmark)

Wac, Katarzyna; Cummings, Mark; Dey, Jayanta

2016-01-01

, high-quality services, we propose an innovative end-to-end service management framework called e2eUberIM. This framework contains a scalable, flexible, and volatile information model (UberIM) and a real-time, "organic" communication and storage process (e2eUber). It leverages the proprietary interfaces...... of different vendors, enabling the resulting enhanced operations system environment to automatically and in real-time optimize operational overhead while maximizing the user experience, and quickly field new innovative, composed "any-services" (XaaS). We document the e2eUberIM requirements and its design...

Imágenes e identidades

OpenAIRE

Guerrini, Sebastión

2013-01-01

Las identidades se estructuran en un proceso de identificación continua con imágenes. Esto afecta no solo a las identidades de las personas, sino también a las de las instituciones, organizaciones y empresas. En este sentido, el rol de ser del Diseño en Comunicación Visual es intentar afectar a las identidades de los espectadores de sus imágenes. Por esta razón, primero es importante definir qué son las imágenes. Facultad de Bellas Artes

Nanocrystallization in Cu-Zr-Al-Sm Bulk Metallic Glasses

Science.gov (United States)

Sikan, Fatih; Yasar, Bengisu; Kalay, Ilkay

2018-04-01

The effect of rare-earth element (Sm) microalloying on the thermal stability and crystallization kinetics of melt-spun ribbons and suction-cast rods of Zr48Cu38.4Al9.6Sm4 alloy were investigated using differential scanning calorimetry (DSC), X-ray diffraction (XRD), transmission electron microscopy (TEM), and atom probe tomography (APT). The XRD results of constant heating rate annealing indicated that amorphous Zr48Cu38.4Al9.6Sm4 melt-spun ribbons devitrifies into Cu2Sm at 673 K (400 °C). The sequence continues with the precipitation of Cu10Zr7 and then these two phases coexist. XRD and TEM studies on 1 mm diameter as suction-cast rods indicated the precipitation of 30-nm-mean size Cu2Sm crystals during solidification. TEM investigation of the isothermal crystallization sequence of melt-spun ribbons and 1-mm-diameter suction-cast rods revealed the precipitation of Cu2Sm nanocrystals at the onset of crystallization and the restriction of the growth of these nanocrystals up to 10 nm diameter with further annealing. APT analysis of 1-mm-diameter suction-cast rods showed that the limited growth of Cu2Sm nanocrystals is due to sluggish diffusion of Sm and Al-Zr pile up at the interface.

λ (Δim) -statistical convergence of order α

Science.gov (United States)

Colak, Rifat; Et, Mikail; Altin, Yavuz

2017-09-01

In this study, using the generalized difference operator Δim and a sequence λ = (λn) which is a non-decreasing sequence of positive numbers tending to ∞ such that λn+1 ≤ λn+1, λ1 = 1, we introduce the concepts of λ (Δim) -statistical convergence of order α (α ∈ (0, 1]) and strong λ (Δim) -Cesàro summablility of order α (α > 0). We establish some connections between λ (Δim) -statistical convergence of order α and strong λ (Δim) -Cesàro summablility of order α. It is shown that if a sequence is strongly λ (Δim) -Cesàro summable of order α, then it is λ (Δim) -statistically convergent of order β in case 0 < α ≤ β ≤ 1.

Advanced Interval Management (IM) Concepts of Operations

Science.gov (United States)

Barmore, Bryan E.; Ahmad, Nash'at N.; Underwood, Matthew C.

2014-01-01

This document provides a high-level description of several advanced IM operations that NASA is considering for future research and development. It covers two versions of IM-CSPO and IM with Wake Mitigation. These are preliminary descriptions to support an initial benefits analysis

Integrating IMS Learning Design and IMS Question and Test Interoperability using CopperCore Service Integration

NARCIS (Netherlands)

Vogten, Hubert; Martens, Harrie; Nadolski, Rob; Tattersall, Colin; Van Rosmalen, Peter; Koper, Rob

2006-01-01

Please, cite this publication as: Vogten, H., Martens, H., Nadolski, R., Tattersall, C., van Rosmalen, P., & Koper, R. (2006). Integrating IMS Learning Design and IMS Question and Test Interoperability using CopperCore Service Integration. Proceedings of International Workshop in Learning Networks

GLASS MELTING PHENOMENA, THEIR ORDERING AND MELTING SPACE UTILISATION

Directory of Open Access Journals (Sweden)

Němec L.

2013-12-01

Full Text Available Four aspects of effective glass melting have been defined – namely the fast kinetics of partial melting phenomena, a consideration of the melting phenomena ordering, high utilisation of the melting space, and effective utilisation of the supplied energy. The relations were defined for the specific melting performance and specific energy consumption of the glass melting process which involve the four mentioned aspects of the process and indicate the potentials of effective melting. The quantity “space utilisation” has been treated in more detail as an aspect not considered in practice till this time. The space utilisation was quantitatively defined and its values have been determined for the industrial melting facility by mathematical modelling. The definitions of the specific melting performance and specific energy consumption have been used for assessment of the potential impact of a controlled melt flow and high space utilisation on the melting process efficiency on the industrial scale. The results have shown that even the partial control of the melt flow, leading to the partial increase of the space utilisation, may considerably increase the melting performance, whereas a decrease of the specific energy consumption was determined to be between 10 - 15 %.

Petrological Geodynamics of Mantle Melting I. AlphaMELTS + Multiphase Flow: Dynamic Equilibrium Melting, Method and Results

Directory of Open Access Journals (Sweden)

Massimiliano Tirone

2017-10-01

Full Text Available The complex process of melting in the Earth's interior is studied by combining a multiphase numerical flow model with the program AlphaMELTS which provides a petrological description based on thermodynamic principles. The objective is to address the fundamental question of the effect of the mantle and melt dynamics on the composition and abundance of the melt and the residual solid. The conceptual idea is based on a 1-D description of the melting process that develops along an ideal vertical column where local chemical equilibrium is assumed to apply at some level in space and time. By coupling together the transport model and the chemical thermodynamic model, the evolution of the melting process can be described in terms of melt distribution, temperature, pressure and solid and melt velocities but also variation of melt and residual solid composition and mineralogical abundance at any depth over time. In this first installment of a series of three contributions, a two-phase flow model (melt and solid assemblage is developed under the assumption of complete local equilibrium between melt and a peridotitic mantle (dynamic equilibrium melting, DEM. The solid mantle is also assumed to be completely dry. The present study addresses some but not all the potential factors affecting the melting process. The influence of permeability and viscosity of the solid matrix are considered in some detail. The essential features of the dynamic model and how it is interfaced with AlphaMELTS are clearly outlined. A detailed and explicit description of the numerical procedure should make this type of numerical models less obscure. The general observation that can be made from the outcome of several simulations carried out for this work is that the melt composition varies with depth, however the melt abundance not necessarily always increases moving upwards. When a quasi-steady state condition is achieved, that is when melt abundance does not varies significantly

Tensile strength of solution-spun, ultradrawn ultrahigh-molecular-weight polyethylene fibers. 1. Influence of fiber diameter

OpenAIRE

Bastiaansen, C.W.M.

1992-01-01

The influence of fiber diam. on the tensile strength of soln.-spun, ultradrawn, ultrahigh-mol.-wt. polyethylene (UHMWPE, mol. wt. >103 kg/mol) fibers was studied. Fibers with a wide range of diams. were produced by varying the polymer concn. in soln. and by applying a drawdown to the fibers. The tensile strength of drawn fibers was compared at a const. Young's modulus in order to eliminate the influence of morphol. parameters, such as degree of chain orientation and extension, on the fracture...

Synthesis and DNA binding properties of 1-(3-aminopropyl)-imidazole-containing triamide f-Im*PyIm: a novel diamino polyamide designed to target 5'-ACGCGT-3'.

Science.gov (United States)

Satam, Vijay; Babu, Balaji; Porte, Alexander; Savagian, Mia; Lee, Megan; Smeltzer, Thomas; Liu, Yang; Ramos, Joseph; Wilson, W David; Lin, Shicai; Kiakos, Kostantinos; Hartley, John A; Lee, Moses

2012-09-15

A novel diamino/dicationic polyamide f-Im(*)PyIm (5) that contains an orthogonally positioned aminopropyl chain on an imidazole (Im(*)) moiety was designed to target 5'-ACGCGT-3'. The DNA binding properties of the diamino polyamide 5, determined by CD, ΔT(M), DNase I footprinting, SPR, and ITC studies, were compared with those of its monoamino/monocationic counterpart f-ImPyIm (1) and its diamino/dicationic isomer f-ImPy(*)Im (2), which has the aminopropyl group attached to the central pyrrole unit (Py(*)). The results gave evidence for the minor groove binding and selectivity of polyamide 5 for the cognate sequence 5'-ACGCGT-3', and with strong affinity (K(eq)=2.3×10(7) M(-1)). However, the binding affinities varied according to the order: f-ImPy(*)Im (2)>f-ImPyIm (1)≥f-Im(*)PyIm (5) confirming that the second amino group can improve affinity, but its position within the polyamide can affect affinity. Copyright © 2012 Elsevier Ltd. All rights reserved.

Structure and magnetic behaviors of melt-spun SmFeSiB ribbons and their nitrides

Energy Technology Data Exchange (ETDEWEB)

Luo, Y.; Zhang, K., E-mail: zhangkunone@gmail.com; Li, K.S.; Yu, D.B.; Ling, J.J.; Men, K.; Dou, Q.Y.; Yan, W.L.; Xie, J.J.; Yang, Y.F.

2016-05-01

SmFe{sub 9.3+x}Si{sub 0.2}B{sub 0.1} (x=0, 0.5, 1.0) ribbons and their nitrides were prepared by melt-spinning, followed by annealing and subsequent nitriding. The structure and magnetic properties have been investigated by means of powder X-ray diffraction, vibrating sample magnetometer and Mossbauer spectroscopy. Rietveld analysis shows that the augment of Fe content gives rise to an increase of the c/a ratio and cell volume. The increasing amount of Fe atoms occupying the 2e sites results in the change of initial structure. It is indicated that the isomer shift of 3g and 6l atom remains quasi-constant while the 2e atom shows a noticeable increase with the increase of iron content, which further conforms the preferential occupation of excessive Fe atoms at this site. Consistent with Tc, the mean hyperfine field 〈B{sub hf}〉 has the highest value of 25.7 T when x=0.5. The hyperfine fields at different Fe sites follow the order H2e>H3g>H6l. The highest curie temperature of 477.68 K and the hyperfine field of 25.7 T in the as-quenched ribbons were obtained when x=0.5. Meanwhile, the highest magnetic properties of H{sub cj}=4.31 kOe, (BH){sub m}=3.5 MGOe in the nitride powders were found. - Highlights: • Rietveld analysis shows that the augment of Fe content gives rise to an increase of the c/a ratio and cell volume. • The isomer shift of 2e atom shows a noticeable increase according to Fe content, which corroborates the preferential occupation of excessive Fe atoms at this site. • The hyperfine fields at various Fe sites follow the order H2e>H3g>H6l, which corresponds closely with the number of iron near neighbor of each site.

Emerging melt quality control solution technologies for aluminium melt

Directory of Open Access Journals (Sweden)

Arturo Pascual, Jr

2009-11-01

Full Text Available The newly developed “MTS 1500” Melt Treatment System is performing the specifi cally required melt treatment operations like degassing, cleaning, modification and/or grain refinement by an automated process in one step and at the same location. This linked process is saving time, energy and metal losses allowing - by automated dosage of the melt treatment agents - the production of a consistent melt quality batch after batch. By linking the MTS Metal Treatment System with sensors operating on-line in the melt, i.e., with a hydrogen sensor “Alspek H”, a fully automated control of parts of the process chain like degassing is possible. This technology does guarantee a pre-specifi ed and documented melt quality in each melt treatment batch. Furthermore, to ensure that castings are consistent and predictable there is a growing realization that critical parameters such as metal cleanliness must be measured prior to casting. There exists accepted methods for measuring the cleanliness of an aluminum melt but these can be both slow and costly. A simple, rapid and meaningful method of measuring and bench marking the cleanliness of an aluminum melt has been developed to offer the foundry a practical method of measuring melt cleanliness. This paper shows the structure and performance of the integrated MTS melt treatment process and documents achieved melt quality standards after degassing, cleaning, modifi cation and grain refi nement operations under real foundry conditions. It also provides an insight on a melt cleanliness measuring device “Alspek MQ” to provide foundry men better tools in meeting the increasing quality and tighter specifi cation demand from the industry.

Ion Mobility Spectrometer / Mass Spectrometer (IMS-MS)

Energy Technology Data Exchange (ETDEWEB)

Hunka, Deborah E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Austin, Daniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2005-10-01

The use of Ion Mobility Spectrometry (IMS)in the Detection of Contraband Sandia researchers use ion mobility spectrometers for trace chemical detection and analysis in a variety of projects and applications. Products developed in recent years based on IMS-technology include explosives detection personnel portals, the Material Area Access (MAA) checkpoint of the future, an explosives detection vehicle portal, hand-held detection systems such as the Hound and Hound II (all 6400), micro-IMS sensors (1700), ordnance detection (2500), and Fourier Transform IMS technology (8700). The emphasis to date has been on explosives detection, but the detection of chemical agents has also been pursued (8100 and 6400).

Disentangled solid state and metastable polymer melt; a solvent free route to high-modulus high-strength tapes and films of UHMWPE

Science.gov (United States)

Rastogi, Sanjay

2013-03-01

Ultra High Molecular Weight Polyethylene (UHMWPE) having average molar mass greater than a million g/mol is an engineering polymer. Due to its light-weight, high abrasion resistance and biocompatibility it is used for demanding applications such as body armour, prostheses etc. At present, because of its high melt viscosity to achieve the uniaxial/biaxial properties in the form of fibers/films the polymer is processed via solution route where nearly 95wt% of the solvent is used to process 5wt% of the polymer. In past several attempts have been made to process the polymer without using any solvent. However, compared to the solvent processing route the achieved mechanical properties were rather poor. Here we show that by controlled synthesis it is feasible to obtain UHMWPE that could be processed free of solvent to make uniaxial tapes and biaxial films, having unprecedented mechanical properties, exceeding that of the solution spun fibers. We address some of the fundamental aspects of chemistry, physics, rheology and processing for the development of desired morphological features to achieve the ultimate mechanical properties in tapes and films. The paper will also address the metastable melt state obtained on melting of the disentangled crystals and its implication on rheology in linear and nonlinear viscoelastic region. Solid state NMR studies will be applied to establish disentangled state in solid state to the polymerisation conditions. References: Macromolecules 2011, 44(14), 5558-5568; Nature Materials 2005, 4, 635-641; Phys Rev Lett 2006, 96(21), 218303-218205. The authors acknowledge financial support by the Dutch Polymer Institute.

A New IMS Based Inter-working Solution

Science.gov (United States)

Zhu, Zhongwen; Brunner, Richard

With the evolution of third generation network, more and more multimedia services are developed and deployed. Any new service to be deployed in IMS network is required to inter-work with existing Internet communities or legacy terminal users in order to appreciate the end users, who are the main drivers for the service to succeed. The challenge for Inter-working between IMS (IP Multimedia Subsystem) and non-IMS network is “how to handle recipient’s address”. This is because each network has its own routable address schema. For instance, the address for Google Talk user is xmpp:xyz@google.com, which is un-routable in IMS network. Hereafter a new Inter-working (IW) solution between IMS and non-IMS network is proposed for multimedia services that include Instant Messaging, Chat, and File transfer, etc. It is an end-to-end solution built on IMS infrastructure. The Public Service Identity (PSI) defined in 3GPP standard (3rd Generation Partnership Project) is used to allow terminal clients to allocate this IW service. When sending the SIP (Session Initial Protocol) request out for multimedia services, the terminal includes the recipient’s address in the payload instead of the “Request-URI” header. In the network, the proposed solution provides the mapping rules between different networks in MM-IW (Multimedia IW). The detailed technical description and the corresponding use cases are present. The comparison with other alternatives is made. The benefits of the proposed solution are highlighted.

Argumentellipse in der "weichen" Nachricht im Deutschen und im Slowenischen

Directory of Open Access Journals (Sweden)

Uršula Krevs

1998-12-01

Full Text Available Argumentellipsen werden in der sprachlichen Kommunikation ohne weiteres akzeptiert, obwohl sie allenfalls in gewissem Sinne wegen ihrer Elliptizität abweichend wirken. Im folgenden interessiert uns, wie die Argumentellipse als syntaktische Entität in den Text eingebettet wird und welche Funktionen sie ausübt. Unsere Aufmerksamkeit gilt bier der Textsorte "weiche" Nachricht, die als Abweichung des Grundmusters gilt. Um im Sprachenpaar Deutsch-Slowenisch die in dieser Textsorte realisierten Argumentellipsen vergleichen zu können, wurde die Homogenität in der Thematik angestrebt und die Texte aus dem gleichen Kommunikationsbereich gewählt. So wurden die Korpora zwei Zeitschriften, die sich mit der gleichen Sportart beschäftigen, entnommen: der deutschen Zeitschrift "Rotpunkt" und der slowenischen Zeitschrift  "Grif '.

Effect of cooling rate and Mg addition on the structural evaluation of rapidly solidified Al-20wt%Cu-12wt%Fe alloy

Energy Technology Data Exchange (ETDEWEB)

Karaköse, Ercan, E-mail: ekarakose@karatekin.edu.tr [Çankırı Karatekin University, Faculty of Sciences, Department of Physics, 18100 Çankırı (Turkey); Çolak, Hakan [Çankırı Karatekin University, Faculty of Sciences, Department of Chemistry, 18100 Çankırı (Turkey)

2016-11-15

The present work examines the effect of Mg contents and cooling rate on the morphology and mechanical properties of Al{sub 20}Cu{sub 12}Fe quasicrystalline alloy. The microstructure of the alloys was analyzed by scanning electron microscopy and the phase composition was identified by X-ray diffractometry. The melting characteristics were studied by differential thermal analysis under an Ar atmosphere. The mechanical features of the melt-spun and conventionally solidified alloys were tested by tensile-strength test and Vickers micro-hardness test. It was found that the final microstructure of the Al{sub 20}Cu{sub 12}Fe samples mainly depends on the cooling rate and Mg contents, which suggests that different cooling rates and Mg contents produce different microstructures and properties. The average grain sizes of the melt spun samples were about 100–300 nm at 35 m/s. The nanosize, dispersed, different shaped quasicrystal particles possessed a remarkable effect to the mechanical characteristics of the rapidly solidified ribbons. The microhardness values of the melt spun samples were approximately 18% higher than those of the conventionally counterparts. - Highlights: •Quasicrystal-creating materials have high potential for applications. •Different shaped nanosize quasicrystal particles were observed. •The addition of Mg has an important impact on the mechanical properties. •H{sub V} values of the MS0, MS3 and MS5 samples at 35 m/s were 8.56, 8.66 and 8.80 GPa. •The volume fraction of IQC increases with increasing cooling rates.

Investigation of structural and magnetic properties of rapidly-solidified iron-silicon alloys at ambient and elevated temperatures

Energy Technology Data Exchange (ETDEWEB)

Jayaraman, T. V.; Meka, V. M.; Jiang, X.; Overman, N. R.; Doyle, J.; Shield, J. E.; Mathaudhu, S. N.

2018-04-01

In this work, we investigated the ambient temperature structural properties (~300 K) and the ambient and high temperature (up to 900 K) direct current (DC) magnetic properties of melt-spun Fe-x wt.% Si (x = 3, 5, & 8) alloys. The wheel surface speeds selected for the study were 30 m/s and 40 m/s. The thickness, width, lattice parameter, saturation magnetization (MS), and intrinsic coercivity (HCI) of the melt spun ribbons are presented and compared with data in the literature. The ribbons produced at the lower wheel surface speed (30 m/s) were continuous having relatively uniform edges compared to the ribbons produced at the higher wheel surface speed. The thickness and the width of the melt-spun ribbons ranged between ~15-60 μm and 500-800 μm, respectively. The x-ray diffraction spectra of the melt-spun ribbons indicated the presence of disordered α-phase, irrespective of the composition, and the wheel-surface speed. The lattice parameter decreased gradually as a function of increasing silicon content from ~0.2862 nm (Fe-3 wt.% Si) to ~0.2847 nm (Fe-8 wt.% Si). Wheel surface speed was not shown to have a significant effect on the magnetization, but primarily impacted the ribbon structure. A decreasing trend in the saturation magnetization was observed as a function of increased silicon content. The intrinsic coercivity of the melt-spun alloys ranged between ~50 to 200 A/m. Elevated temperature evaluation of the magnetization in the case of Fe-3 & 5 wt.% Si alloy ribbons was distinctly different from the Fe-8 wt.% Si alloy ribbons. The curves of the as-prepared Fe-3 wt.% Si and Fe-5 wt.% Si alloy ribbons were irreversible while that of Fe-8 wt.% Si was reversible. The MS for any of the combinations of wheel surface speed and composition decreased monotonically with the increase in temperature (from 300 – 900 K). The percentage decrease in MS from 300 K to 900 K for the Fe-3 wt.% Si and Fe-5 wt.% Si alloys was ~19-22 %, while the percentage decrease in the same

Volatile diffusion in silicate melts and its effects on melt inclusions

Directory of Open Access Journals (Sweden)

P. Scarlato

2005-06-01

Full Text Available A compendium of diffusion measurements and their Arrhenius equations for water, carbon dioxide, sulfur, fluorine, and chlorine in silicate melts similar in composition to natural igneous rocks is presented. Water diffusion in silicic melts is well studied and understood, however little data exists for melts of intermediate to basic compositions. The data demonstrate that both the water concentration and the anhydrous melt composition affect the diffusion coefficient of water. Carbon dioxide diffusion appears only weakly dependent, at most, on the volatilefree melt composition and no effect of carbon dioxide concentration has been observed, although few experiments have been performed. Based upon one study, the addition of water to rhyolitic melts increases carbon dioxide diffusion by orders of magnitude to values similar to that of 6 wt% water. Sulfur diffusion in intermediate to silicic melts depends upon the anhydrous melt composition and the water concentration. In water-bearing silicic melts sulfur diffuses 2 to 3 orders of magnitude slower than water. Chlorine diffusion is affected by both water concentration and anhydrous melt composition; its values are typically between those of water and sulfur. Information on fluorine diffusion is rare, but the volatile-free melt composition exerts a strong control on its diffusion. At the present time the diffusion of water, carbon dioxide, sulfur and chlorine can be estimated in silicic melts at magmatic temperatures. The diffusion of water and carbon dioxide in basic to intermediate melts is only known at a limited set of temperatures and compositions. The diffusion data for rhyolitic melts at 800°C together with a standard model for the enrichment of incompatible elements in front of growing crystals demonstrate that rapid crystal growth, greater than 10-10 ms-1, can significantly increase the volatile concentrations at the crystal-melt interface and that any of that melt trapped

Synthetic spider silk fibers spun from Pyriform Spidroin 2, a glue silk protein discovered in orb-weaving spider attachment discs.

Science.gov (United States)

Geurts, Paul; Zhao, Liang; Hsia, Yang; Gnesa, Eric; Tang, Simon; Jeffery, Felicia; La Mattina, Coby; Franz, Andreas; Larkin, Leah; Vierra, Craig

2010-12-13

Spider attachment disc silk fibers are spun into a viscous liquid that rapidly solidifies, gluing dragline silk fibers to substrates for locomotion or web construction. Here we report the identification and artificial spinning of a novel attachment disc glue silk fibroin, Pyriform Spidroin 2 (PySp2), from the golden orb weaver Nephila clavipes . MS studies support PySp2 is a constituent of the pyriform gland that is spun into attachment discs. Analysis of the PySp2 protein architecture reveals sequence divergence relative to the other silk family members, including the cob weaver glue silk fibroin PySp1. PySp2 contains internal block repeats that consist of two subrepeat units: one dominated by Ser, Gln, and Ala and the other Pro-rich. Artificial spinning of recombinant PySp2 truncations shows that the Ser-Gln-Ala-rich subrepeat is sufficient for the assembly of polymeric subunits and subsequent fiber formation. These studies support that both orb- and cob-weaving spiders have evolved highly polar block-repeat sequences with the ability to self-assemble into fibers, suggesting a strategy to allow fiber fabrication in the liquid environment of the attachment discs.

IMS Learning Design Frequently Asked Questions

NARCIS (Netherlands)

Tattersall, Colin; Manderveld, Jocelyn; Hummel, Hans; Sloep, Peter; Koper, Rob; De Vries, Fred

2004-01-01

This list of frequently asked questions was composed on the basis of questions asked of the Educational Technology Expertise Centrum. The questions addessed are: Where can I find the IMS Learning Design Specification? What is meant by the phrase “Learning Design”? What is the IMS LD Specification

Double melting in polytetrafluoroethylene γ-irradiated above its melting point

International Nuclear Information System (INIS)

Serov, S.A.; Khatipov, S.A.; Sadovskaya, N.V.; Tereshenkov, A.V.; Chukov, N.A.

2012-01-01

Highlights: ► PTFE irradiation leads to formation of double melting peaks in DSC curves. ► This is connected to dual crystalline morphology typical for PTFE. ► Two crystalline types exist in the PTFE irradiated in the melt. - Abstract: PTFE irradiation above its melting point leads to formation of double melting and crystallization peaks in DSC curves. Splitting of melting peaks is connected to dual crystalline morphology typical for PTFE irradiated in the melt. According to electron microscopy, two crystalline types with different size and packing density exist in the irradiated PTFE.

Corrigendum to Development of a Doxycycline Hydrochloride-Loaded Electro spun Nano fibrous Membrane for GTR/GB R Applications

International Nuclear Information System (INIS)

Jia, L. N.; Xu, H. Y.; Hu, X. G.; Xie, Q.; Wang, W.; Jia, J.; Zhang, X.; Hua, F.

2016-01-01

In the article titled Development of a Doxycycline Hydrochloride-Loaded Electro spun Nano fibrous Membrane for GTR/GBR Applications [1], there was an error in the Acknowledgments section, which should be corrected as follows: The authors would like to acknowledge the financial support by the National Science Foundation of China (no. 81271136). This investigation was supported by School of Stomatology, Institute of Material Medical School of Pharmacy, and Department of Military Toxicology, the Fourth Military Medical University.

Resilience of the IMS system

DEFF Research Database (Denmark)

Kamyod, Chayapol; Nielsen, Rasmus Hjorth; Prasad, Neeli R.

2014-01-01

The paper focuses on end-to-end resilience analysis of the IMS based network through the principal resilience parameters by using OPNET. The resilience behaviours of communication across multiple IMS domains are investigated at different communication scenarios and compared with previous state......-of-the-art. Moreover, the resilience effects when adding a redundancy of the S-CSCF unit are examined. The results disclose interesting resilience behaviours for long distance communications....

Structures and Electrochemical Hydrogen Storage Properties of the As-Spun RE-Mg-Ni-Co-Al-Based AB2-Type Alloys Applied to Ni-MH Battery

Science.gov (United States)

Zhang, Yanghuan; Yuan, Zeming; Shang, Hongwei; Li, Yaqin; Qi, Yan; Zhao, Dongliang

2017-05-01

In this paper, the La0.8- x Ce0.2Y x MgNi3.5Co0.4Al0.1 ( x = 0, 0.05, 0.1, 0.15, 0.2) alloys were synthesized via smelting and melt spinning. The effect of Y content on the structure and electrochemical hydrogen storage characteristics of the as-cast and spun alloys was investigated. The identifications of XRD and SEM demonstrate that the experimental alloys possess a major phase LaMgNi4 and a minor phase LaNi5. The variation of Y content results in an obvious transformation of the phase abundance rather than phase composition in the alloys, namely LaMgNi4 phase increases while LaNi5 phase decreases with Y content growing. Furthermore, the replacement of Y for La causes the lattice constants and cell volume to clearly decrease and markedly refines the alloy grains. The electrochemical tests reveal that these alloys can obtain the maximum values of discharge capacity at the first cycling without any activation needed. With Y content growing, the discharge capacity of the alloys obviously declines, but its cycle stability remarkably improves. Moreover, the electrochemical dynamics of the alloys, involving the high-rate discharge ability, hydrogen diffusion coefficient ( D), limiting current density ( I L), and charge transfer rate, initially augment and then decrease with rising Y content.

Novel Technique for Quantitative Fast Scanning Calorimetry on Electrospun Fibers

Science.gov (United States)

Thomas, David; Govinna, Nelaka; Schick, Christoph; Cebe, Peggy

Fast scanning chip calorimetry allows for the study of polymers which have rapid nucleation and/or crystallization kinetics, or degrade within their melting range. Heating rates used, up to 4000 K/s, allow studies of hetero and homogeneous nucleation at time scales inaccessible with conventional calorimeters, whose rates are typically alcohol (PVA) were chosen in the development of a new methodology to obtain quantitative fast scanning thermal data from electrospun nanofibers using a Flash DSC1. The structure of nanofibers requires special methods to load nanogram-sized samples onto a UFSC1 sensor. Fibers were directly spun onto TEM grids which provide a durable substrate to support bundles of nanofibers and possess excellent thermal conductivity allowing for a strong, repeatable signal and ensure good sample to sensor contact. As spun samples were held isothermally at temperatures ranging from Tg to Tm then heated at 2,000 K/s to assess as-spun crystallinity and cold crystallization behaviors. Above Tm the fibers break up into micro- and nano-droplets. On these samples, melt crystallization experiments were performed to study nucleation and crystallization of polymer confined to nanodroplet morphology. NSF DMR-1608125.

Individualisierte Produkte im Fokus der intergrierten Produktentwicklung

OpenAIRE

Baumberger, C.;Gahr, A.

2017-01-01

Individualisierte Produkte stellen neue Herausforderungen an die Produktentwicklung – vornehmlich im Bereich der Produktstrukturplanung, der kundenindividuellen Produktadaption und dem Zielkostenmanagement. Diese Themen werden am Lehrstuhl für Produktentwicklung im Rahmen des Sonderforschungsbereiches 582 behandelt.

Managing P2P services via the IMS

NARCIS (Netherlands)

Liotta, A.; Lin, L.

2007-01-01

The key aim of our work was to illustrate the benefits and means to deploy P2P services via the IMS. Having demonstrated the technical viability of P2P-IMS we have also found a way to add a new management dimension to existing P2P systems. P2P-IMS comes with a natural "data management" mechanism,

Melting method for miscellaneous radioactive solid waste and melting furnace

International Nuclear Information System (INIS)

Osaki, Toru; Furukawa, Hirofumi; Uda, Nobuyoshi; Katsurai, Kiyomichi

1998-01-01

A vessel containing miscellaneous solid wastes is inserted in a crucible having a releasable material on the inner surface, they are induction-heated from the outside of the crucible by way of low temperature heating coils to melt low melting point materials in the miscellaneous wastes within a temperature range at which the vessel does not melt. Then, they are induction-heated by way of high temperature heating coils to melt the vessel and not yet melted materials, those molten materials are cooled, solidified molten material and the releasable material are taken out, and then the crucible is used again. Then, the crucible can be used again, so that it can be applied to a large scaled melting furnace which treats wastes by a unit of drum. In addition, since the cleaning of the used crucible and the application of the releasable material can be conducted without interrupting the operation of the melting furnace, the operation cycle of the melting furnace can be shortened. (N.H.)

Geschlechterstereotype im Einsatz

Directory of Open Access Journals (Sweden)

Erika Kegyes

2007-11-01

Full Text Available Die umfangreiche Monographie gehört zum Forschungsbereich der kritischen angewandten Linguistik (Critical Applied Linguistics und liegt sowohl theoretisch als auch praktisch im Schnittpunkt der gender- und werbesprachlichen Untersuchungen.

Muriithi, IM

African Journals Online (AJOL)

Muriithi, IM. Vol 8, No 2 (2014) - Articles Correlation of magnetic resonance imaging findings with arthroscopy in the evaluation of rotator cuff pathology. Abstract PDF · Vol 8, No 2 (2014) - Articles Patterns of knee, hip and hand osteoarthritis in Kenyatta National Hospital Abstract PDF. ISSN: 1994-1072. AJOL African ...

Ion mobility spectrometer / mass spectrometer (IMS-MS).

Energy Technology Data Exchange (ETDEWEB)

Hunka Deborah Elaine; Austin, Daniel E.

2005-07-01

The use of Ion Mobility Spectrometry (IMS) in the Detection of Contraband Sandia researchers use ion mobility spectrometers for trace chemical detection and analysis in a variety of projects and applications. Products developed in recent years based on IMS-technology include explosives detection personnel portals, the Material Area Access (MAA) checkpoint of the future, an explosives detection vehicle portal, hand-held detection systems such as the Hound and Hound II (all 6400), micro-IMS sensors (1700), ordnance detection (2500), and Fourier Transform IMS technology (8700). The emphasis to date has been on explosives detection, but the detection of chemical agents has also been pursued (8100 and 6400). Combining Ion Mobility Spectrometry (IMS) with Mass Spectrometry (MS) is described. The IMS-MS combination overcomes several limitations present in simple IMS systems. Ion mobility alone is insufficient to identify an unknown chemical agent. Collision cross section, upon which mobility is based, is not sufficiently unique or predictable a priori to be able to make a confident peak assignment unless the compounds present are already identified. Molecular mass, on the other hand, is much more readily interpreted and related to compounds. For a given compound, the molecular mass can be determined using a pocket calculator (or in one's head) while a reasonable value of the cross-section might require hours of computation time. Thus a mass spectrum provides chemical specificity and identity not accessible in the mobility spectrum alone. In addition, several advanced mass spectrometric methods, such as tandem MS, have been extensively developed for the purpose of molecular identification. With an appropriate mass spectrometer connected to an ion mobility spectrometer, these advanced identification methods become available, providing greater characterization capability.

Bremssysteme im Personenkraftwagen

Science.gov (United States)

Reif, Konrad

Für die ersten drei Punkte ist die Betriebsbremsanlage ("Fußbremse“) zuständig. Der Fahrer aktiviert sie durch Betätigen des Bremspedals. Die Feststellbremsanlage ("Handbremse“) hält das Fahrzeug im Stillstand.

Support interoperability and reusability of emerging forms of assessment: Some issues on integrating IMS LD with IMS QTI

NARCIS (Netherlands)

Miao, Yongwu; Boon, Jo; Van der Klink, Marcel; Sloep, Peter; Koper, Rob

2009-01-01

Miao, Y., Boon, J., Van der Klink, M., Sloep, P. B., & Koper, R. (2011). Support interoperability and reusability of emerging forms of assessment: Some issues on integrating IMS LD with IMS QTI. In F. Lazarinis, S. Green, & E. Pearson (Eds.), E-Learning Standards and Interoperability: Frameworks

Tin in granitic melts: The role of melting temperature and protolith composition

Science.gov (United States)

Wolf, Mathias; Romer, Rolf L.; Franz, Leander; López-Moro, Francisco Javier

2018-06-01

Granite bound tin mineralization typically is seen as the result of extreme magmatic fractionation and late exsolution of magmatic fluids. Mineralization, however, also could be obtained at considerably less fractionation if initial melts already had enhanced Sn contents. We present chemical data and results from phase diagram modeling that illustrate the dominant roles of protolith composition, melting conditions, and melt extraction/evolution for the distribution of Sn between melt and restite and, thus, the Sn content of melts. We compare the element partitioning between leucosome and restite of low-temperature and high-temperature migmatites. During low-temperature melting, trace elements partition preferentially into the restite with the possible exception of Sr, Cd, Bi, and Pb, that may be enriched in the melt. In high-temperature melts, Ga, Y, Cd, Sn, REE, Pb, Bi, and U partition preferentially into the melt whereas Sc, V, Cr, Co, Ni, Mo, and Ba stay in the restite. This contrasting behavior is attributed to the stability of trace element sequestering minerals during melt generation. In particular muscovite, biotite, titanite, and rutile act as host phases for Sn and, therefore prevent Sn enrichment in the melt as long as they are stable phases in the restite. As protolith composition controls both the mineral assemblage and modal contents of the various minerals, protolith composition eventually also controls the fertility of a rock during anatexis, restite mineralogy, and partitioning behavior of trace metals. If a particular trace element is sequestered in a phase that is stable during partial melting, the resulting melt is depleted in this element whereas the restite becomes enriched. Melt generation at high temperature may release Sn when Sn-hosts become unstable. If melt has not been lost before the breakdown of Sn-hosts, Sn contents in the melt will increase but never will be high. In contrast, if melt has been lost before the decomposition of Sn

Politische Inhalte im Internet: Angebot und Nachfrage politischer Inhalte im World Wide Web am Beispiel von Volksabstimmungen in der Schweiz

OpenAIRE

Rademacher, Patrick Horst Josef

2010-01-01

Welche Bedeutung kommt dem Internet in der Politikvermittlung zu? Dieser Frage geht Patrick Rademacher nach, indem er untersucht, welche Anbieter politische Inhalte im Internet zur Verfügung stellen, wie sie dabei vorgehen und wie die Struktur der Inhalte beschaffen ist. Darüber hinaus analysiert er, inwiefern die online angebotenen Inhalte auf eine Nachfrage durch die Bürger treffen. Im Untersuchungskontext von Volksabstimmungen in der Schweiz hat der Autor hierfür im Jahr 2008 umfangreiche ...

Comparative Study on Two Melting Simulation Methods: Melting Curve of Gold

International Nuclear Information System (INIS)

Liu Zhong-Li; Li Rui; Sun Jun-Sheng; Zhang Xiu-Lu; Cai Ling-Cang

2016-01-01

Melting simulation methods are of crucial importance to determining melting temperature of materials efficiently. A high-efficiency melting simulation method saves much simulation time and computational resources. To compare the efficiency of our newly developed shock melting (SM) method with that of the well-established two-phase (TP) method, we calculate the high-pressure melting curve of Au using the two methods based on the optimally selected interatomic potentials. Although we only use 640 atoms to determine the melting temperature of Au in the SM method, the resulting melting curve accords very well with the results from the TP method using much more atoms. Thus, this shows that a much smaller system size in SM method can still achieve a fully converged melting curve compared with the TP method, implying the robustness and efficiency of the SM method. (paper)

Gruppenbezogene Menschenfeindlichkeit im Sport in Brandenburg

OpenAIRE

Delto, Hannes; Tzschoppe, Petra

2016-01-01

Mit der Querschnittsstudie "Wir und die Anderen – Gruppenbezogene Menschenfeindlichkeit im organisierten Sport in Brandenburg" wurde das Syndrom Gruppenbezogener Menschenfeindlichkeit im organisierten Sport untersucht. Das Konzept der Gruppenbezogenen Menschenfeindlichkeit – ausgehend von einer Ideologie der Ungleichwertigkeit – wurde von Prof. Wilhelm Heitmeyer (Universität Bielefeld) entwickelt. Die Ergebnisse ermöglichen explizite Aussagen über Ausmaß und Ursachen Gruppenbezogener Menschen...

Verletzungen und Fehlbeanspruchungen im leistungsorientierten Rudersport

OpenAIRE

Bussian, Marc Robert

2004-01-01

Die Stellung der Breitensportart Rudern als gesundheitsfördernde Sportform ist in der Literatur gleichlautend positiv beschrieben. Im leistungsorientierten Rudersport müssen neben den Verletzungen und Fehlbeanspruchungen der eigentlichen Sportart die unabdingbaren Nebentrainingsformen berücksichtigt werden. In den neunziger Jahren vollzog sich ein trainingsmethodischer Wandel, die Einführung eines erschwinglichen Rudersimulators und eine technische Weiterentwicklung im Boots- und Ruderbau. Ei...

Pengaruh Intensitas Mengakses Twitter Duta Im3 terhadap Kepuasan Pengalaman Adopsi dan Kepuasan Pengalaman Adopsi terhadap Keputusan Penggunaan Program Im3

OpenAIRE

Ayu Kinasih, Diyan Hafdinovianti; Pradekso, Tandiyo; Setiabudi, Djoko

2014-01-01

Nama : Diyan H Ayu KinasihNIM : D2C009029Judul : Pengaruh Intensitas Mengakses Twitter Duta IM3 terhadapKepuasan Pengalaman Adopsi dan Kepuasan PengalamanAdopsi terhadap Keputusan Penggunaan Program IM3ABSTRAKTwitter sebagai salah satu promotion tools yang digunakan oleh PTIndosat Tbk, diharapkan dapat memperkenalkan program-program serta eventyang dilakukan oleh Indosat. Melalui duta IM3 sebagai brand ambassador, Indosatmencoba meraih pasar anak muda dengan melakukan kegiatan promosi.Tipe pe...

The Application of Internal Marketing (IM in a Service Organization

Directory of Open Access Journals (Sweden)

R. Sharma

2013-07-01

Findings and Strategic Implications. To complement earlier theoretical proposition on IM, the findings indicate that there are several empirical aspects such as “costs, people and concept” which hinder successful implementation of IM. This study proposes several strategic HR recommendations to reduce the “implementation gap” in IM such as to conduct continuous staff training on IM knowledge on regular time intervals, to reduce excessive work load and pressure and engaging staff members in continuous personal development sessions. In addition, the findings reveal that IM training should be given priority to solve “people-oriented” issues.

Electron microscopy investigations of rapidly solidified Fe-Zr-B-Cu alloys

International Nuclear Information System (INIS)

Majumdar, B.; Arvindha Babu, D.; Akhtar, D.

2010-01-01

Rapidly solidified Fe-based nanocrystalline soft magnetic materials possess a unique combination of properties i,e high permeability, saturation and Curie temperature and very low coercivity which are otherwise not attainable in conventional soft magnetic materials. The alloys are processed by producing amorphous phase through melt spinning route followed by a partial devitrification for incorporation of nanocrystalline phase in the amorphous matrix. In this paper, detailed electron microscopic investigations of melt spun Fe-Zr-B-Cu alloys are presented. Melt spun ribbons of Fe 99-x-y Zr x BCu 1 alloys with x+y = 11 and x+y = 13 were prepared under different wheel speed conditions and then vacuum annealed for 1 h at different temperatures. The microstructure changes from completely amorphous to a cellular/dendritic bcc solid solution coexisting with the amorphous phase at intercellular/dendritic regions when Zr/B ratio or the process parameters are varied. Annealing leads to the precipitation of nanocrystalline bcc-Fe phase from both amorphous phase and already existing bcc solid solution. (author)

Olivine/melt transition metal partitioning, melt composition, and melt structure—Melt polymerization and Qn-speciation in alkaline earth silicate systems

Science.gov (United States)

Mysen, Bjorn O.

2008-10-01

The two most abundant network-modifying cations in magmatic liquids are Ca 2+ and Mg 2+. To evaluate the influence of melt structure on exchange of Ca 2+ and Mg 2+ with other geochemically important divalent cations ( m-cations) between coexisting minerals and melts, high-temperature (1470-1650 °C), ambient-pressure (0.1 MPa) forsterite/melt partitioning experiments were carried out in the system Mg 2SiO 4-CaMgSi 2O 6-SiO 2 with ⩽1 wt% m-cations (Mn 2+, Co 2+, and Ni 2+) substituting for Ca 2+ and Mg 2+. The bulk melt NBO/Si-range ( NBO/Si: nonbridging oxygen per silicon) of melt in equilibrium with forsterite was between 1.89 and 2.74. In this NBO/Si-range, the NBO/Si(Ca) (fraction of nonbridging oxygens, NBO, that form bonds with Ca 2+, Ca 2+- NBO) is linearly related to NBO/Si, whereas fraction of Mg 2+- NBO bonds is essentially independent of NBO/Si. For individual m-cations, rate of change of KD( m-Mg) with NBO/Si(Ca) for the exchange equilibrium, mmelt + Mg olivine ⇌ molivine + Mg melt, is linear. KD( m-Mg) decreases as an exponential function of increasing ionic potential, Z/ r2 ( Z: formal electrical charge, r: ionic radius—here calculated with oxygen in sixfold coordination around the divalent cations) of the m-cation. The enthalpy change of the exchange equilibrium, Δ H, decreases linearly with increasing Z/ r2 [Δ H = 261(9)-81(3)· Z/ r2 (Å -2)]. From existing information on (Ca,Mg)O-SiO 2 melt structure at ambient pressure, these relationships are understood by considering the exchange of divalent cations that form bonds with nonbridging oxygen in individual Qn-species in the melts. The negative ∂ KD( m-Mg) /∂( Z/ r2) and ∂(Δ H)/∂( Z/ r2) is because increasing Z/ r2 is because the cations forming bonds with nonbridging oxygen in increasingly depolymerized Qn-species where steric hindrance is decreasingly important. In other words, principles of ionic size/site mismatch commonly observed for trace and minor elements in crystals, also

Wozu und wie kooperative Arbeitsformen im studienbegleitenden Deutschunterricht?

Directory of Open Access Journals (Sweden)

Karmelka Barić

2016-04-01

Full Text Available Ausgehend von einer Reflexion über die im Beruf und im Leben notwendigen Kompetenzen in der Kommunikation sowie von der Überzeugung, dass es notwendig ist, diese Kompetenzen schon im Studium durch geeignete Arbeitsverfahren und Themen zu entwickeln, werden Kooperation und Autonomie fördernde Arbeitsformen für den studienbegleitenden Deutsch- und Fremdsprachenunterricht (SDU/SFU vorgestellt. Diese Arbeitsformen sind auf andere Sprachen übertragbar und aus dem Lehrwerk Mit Deutsch studieren arbeiten leben A2/B1 (Lévy-Hillerich, Serena, Barić & Cickovska 2010 und der dazu gehörenden Lernplattform entnommen. Das Lehrwerk selbst ist eine Umsetzung der SDU-Rahmencurricula, die im Laufe von über zwanzig Jahren in zehn Ländern im Rahmen eines 1994 am Goethe-Institut Warschau begonnenen Hochschulprojekts und der daraus entstandenen Forschungstätigkeit entstanden sind. Grundlage des Projekts ist ein ganzheitlicher soziopädagogischer Ansatz, der LernerInnen als Menschen betrachtet, die im Präsenz- oder im virtuellen Unterricht in der Sprache und durch die Sprache fach- und sprachübergreifende Kooperationsfähigkeiten entwickeln, die sich später im Leben in der Gesellschaft auswirken. Nach der Vorstellung des Projekts und seiner wissenschaftlichen Hintergründe im ersten Teil des Beitrags werden im zweiten Teil die sich aus dem Ansatz ergebenden Arbeitsformen untersucht: Dabei werden die sich dazu eignenden Themen, die Lernhilfen für StudentInnen, die den LehrerInnen zufallenden Rollen sowie die Ansprüche an Lehrbücher/Unterrichtsmaterialien und Online-/Blended-Learning-Lernszenarien besprochen. Der abschließende Überblick im dritten Teil über die Schwierigkeiten, die beim kooperativen Lernen im SDU/SFU auftreten können, ist gleichzeitig eine offenbleibende Frage danach, wie LehrerInnen aus- und fortgebildet werden sollten, um sich den Anforderungen einer sich dauernd verändernden Lernlandschaft stellen zu können.   The paper

Die Rule of Law im Völker- und im Europarecht – aktuelle Probleme

Directory of Open Access Journals (Sweden)

Helmut Tichy

2015-04-01

Full Text Available Diese am 5. März 2015 in Graz gehaltene Antrittsvorlesung eines Praxisprofessors, der im Hauptberuf Leiter des Völkerrechtsbüros im österreichischen Außenministerium ist, beschäftigt sich mit dem Begriff der Herrschaft des Rechts in den internationalen Beziehungen (Rule of Law und mit den Möglichkeiten Österreichs, zur Stärkung der Rule of Law und zur Lösung aktueller Probleme beizutragen. Dabei werden insbesondere die Mitwirkung an Kodifikationsbemühungen und an der Verbesserung der Einhaltung des humanitären Völkerrechts, die Umsetzung der Menschenrechte (auch in Österreich und Fragen der internationalen Gerichtsbarkeit angesprochen.

Permeability and 3-D melt geometry in shear-induced high melt fraction conduits

Science.gov (United States)

Zhu, W.; Cordonnier, B.; Qi, C.; Kohlstedt, D. L.

2017-12-01

Observations of dunite channels in ophiolites and uranium-series disequilibria in mid-ocean ridge basalt suggest that melt transport in the upper mantle beneath mid-ocean ridges is strongly channelized. Formation of high melt fraction conduits could result from mechanical shear, pyroxene dissolution, and lithological partitioning. Deformation experiments (e.g. Holtzman et al., 2003) demonstrate that shear stress causes initially homogeneously distributed melt to segregate into an array of melt-rich bands, flanked by melt-depleted regions. At the same average melt fraction, the permeability of high melt fraction conduits could be orders of magnitude higher than that of their homogenous counterparts. However, it is difficult to determine the permeability of melt-rich bands. Using X-ray synchrotron microtomography, we obtained high-resolution images of 3-dimensional (3-D) melt distribution in a partially molten rock containing shear-induced high melt fraction conduits. Sample CQ0705, an olivine-alkali basalt aggregate with a nominal melt fraction of 4%, was deformed in torsion at a temperature of 1473 K and a confining pressure of 300 MPa to a shear strain of 13.3. A sub-volume of CQ0705 encompassing 3-4 melt-rich bands was imaged. Microtomography data were reduced to binary form so that solid olivine is distinguishable from basalt glass. At a spatial resolution of 160 nm, the 3-D images reveal the shape and connectedness of melt pockets in the melt-rich bands. Thin melt channels formed at grain edges are connected at large melt nodes at grain corners. Initial data analysis shows a clear preferred orientation of melt pockets alignment subparallel to the melt-rich band. We use the experimentally determined geometrical parameters of melt topology to create a digital rock with identical 3-D microstructures. Stokes flow simulations are conducted on the digital rock to obtain the permeability tensor. Using this digital rock physics approach, we determine how deformation

Gruppenbezogene Menschenfeindlichkeit im Sport in Sachsen

OpenAIRE

Delto, Hannes; Tzschoppe, Petra

2015-01-01

Mit der Querschnittsstudie „Wir und die Anderen – Gruppenbezogene Menschenfeindlichkeit im organisierten Sport in Sachsen“ wurde erstmals das Syndrom Gruppenbezogener Menschenfeindlichkeit im organisierten Sport untersucht. Das Konzept der Gruppenbezogenen Menschenfeindlichkeit – ausgehend von einer Ideologie der Ungleichwertigkeit – wurde von Prof. Wilhelm Heitmeyer (Universität Bielefeld) entwickelt. Die Ergebnisse ermöglichen explizite Aussagen über Ausmaß und Ursachen Gruppenbezogener Men...

Usability test of the ImPRO, computer-based procedure system

International Nuclear Information System (INIS)

Jung, Y.; Lee, J.

2006-01-01

ImPRO is a computer based procedure in both flowchart and success logic tree. It is evaluated on the basis of computer based procedure guidelines. It satisfies most requirements such as presentations and functionalities. Besides, SGTR has been performed with ImPRO to evaluate reading comprehension and situation awareness. ImPRO is a software engine which can interpret procedure script language, so that ImPRO is reliable by nature and verified with formal method. One bug, however, had hidden one year after release, but it was fixed. Finally backup paper procedures can be prepared on the same format as VDU in case of ImPRO failure. (authors)

Midlatitude magnetometer chains during the IMS

International Nuclear Information System (INIS)

Mcpherron, R.L.

1982-01-01

The International Magnetospheric Study (IMS) is an international program to study global problems of magnetospheric dynamics. A key element of the U.S. participation in this program was the establishment of a ground magnetometer network. This network included a number of arrays at high and low latitudes. This report describes three chains established at midlatitudes, including the IMS Midlatitude Chain, the AFGL Magnetometer Network, and the Bell Lab Conjugate Array. Descriptions of the type of equipment, station locations, types of data display, and availability of data for each chain are presented in this report. A major problem of the data analysis phase of the IMS will be reducing selected subsets of these data to a common format. Currently, there are no plans to do this in a systematic manner

Efficient second harmonic generation by para-nitroaniline embedded in electro-spun polymeric nanofibres

Science.gov (United States)

Gonçalves, Hugo; Saavedra, Inês; Ferreira, Rute AS; Lopes, PE; de Matos Gomes, Etelvina; Belsley, Michael

2018-03-01

Intense well polarized second harmonic light was generated by poly(methyl methacrylate) nanofibres with embedded para-nitroaniline nanocrystals. Subwavelength diameter fibres were electro-spun using a 1:2 weight ratio of chromophore to polymer. Analysis of the generated second harmonic light indicates that the para-nitroaniline molecules, which nominally crystalize in the centrosymmetric space group, were organized into noncentrosymmetric structures leading to a second order susceptibility dominated by a single tensor element. Under the best deposition conditions, the nanofibrers display an effective nonlinear optical susceptibility approximately two orders of magnitude greater than that of potassium dihydrogen phosphate. Generalizing this approach to a broad range of organic molecules with strong individual molecular second order nonlinear responses, but which nominally form centrosymmetric organic crystals, could open a new pathway for the fabrication of efficient sub-micron sized second harmonic light generators.

Implantate im Mittelohrbereich - Teil 2 (Ergänzungen 2007)

Science.gov (United States)

Stieve, M.; Lenarz, Thomas

In Deutschland leben ca. 12 Millionen Menschen, die an einer ein- oder beidseitigen Schwerhörigkeit leiden. Diese kann angeboren oder im Laufe des Lebens erworben sein. Klinisch und therapeutisch wichtig ist die Unterscheidung hinsichtlich des Schädigungsortes im Bereich des Mittelohres, d. h. eine Schalleitungsschwerhörigkeit, oder im Bereich des Innenohres, d. h. eine Schallempfindungsschwerhörigkeit, wobei hier der Schädigungsort auch am Hörnerven oder in den zentralen Hörabschnitten liegen kann. Therapeutisch lassen sich sowohl Schwerhörigkeiten im Bereich des Mittelohres als auch im Innenohr und sogar im Hirnstammbereich (Hirnstammimplantat) behandeln. 1,9 Millionen Schwerhörige haben eine Erkrankung im Mittelohrbereich, d. h. der Schall kann nur ungenügend auf das Innenohr übertragen werden. Die Ursache besteht meist in einer chronischen Mittelohrentzündung, die zu einer Zerstörung des Trommelfells und der Gehörknöchelchenkette geführt haben. Therapeutisch und damit als Prinzip der operativen Hörverbesserung steht primär der Verschluß des Trommelfells oder eine Rekonstruktion der Gehörknöchelchen. Mittelohroperationen werden mikrochirurgisch unter dem Operationsmikroskop durchgeführt, wobei zunächst durch eine sanierende Operation der Entzündungsprozeß entfernt wird und nach einer Ausheilungszeit die Gehörknöchelchenkette durch künstliche Prothesen rekonstruiert werden kann.

Minería de imágenes

OpenAIRE

Fernández, Jacqueline; Miranda, Natalia Carolina; Guerrero, Roberto A.; Piccoli, María Fabiana

2006-01-01

Durante los últimos años, la proliferación de los medios digitales ha creado la necesidad del desarrollo de herramientas para la eficiente representación, acceso y recuperación de información visual. La minería de imágenes se ha convertido en una importante rama de investigación a causa del potencial que posee en descubrir patrones característicos a partir de un importante conjunto de imágenes. No obstante, la minería de imágenes es más que una simple extensión de la minería de datos al domin...

From mains frequency to converter power supply in foundry melting operations; Von der Netzfrequenz- zur Umrichter-Stromversorgung im Schmelzbetrieb der Eisengiesserei

Energy Technology Data Exchange (ETDEWEB)

Doetsch, Erwin; Yildir, Yilmaz [ABP Induction Systems GmbH, Dortmund (Germany); Koch, Frank [Gusstec Weiherhammer GmbH, Weiherhammer (Germany)

2010-06-15

As is well known, converter-based power feed has now largely superseded line-frequency technology as state-of-the-art in supply of induction melting facilities. Replacement of LF power supply systems with converters is therefore the main priority in the context of projects for modernization of existing induction installations. The objective is generally to leave the crucible furnace and its peripherals effectively as they are, and match the output and frequency of the converter to their needs. The following article states the criteria that need to be taken into account in this context and examines a specific modernization project, using the example of Gusstec Weiherhammer GmbH's iron melting installation. (orig.)

Die Pluralbildung im Deutschen - ein Versuch im Rahmen der Optimalitätstheorie

Directory of Open Access Journals (Sweden)

Wegener, Heide

1999-01-01

Full Text Available Die Pluralbildung im Deutschen ist nicht chaotisch, aber komplex. Unabhängig davon, ob man für die Pluralbildung Regeln, Schemata oder die Wortstruktur als Erklärungsmodell benutzt, bleibt die Tatsache einer beachtlichen Zahl miteinander konkurrierender Formen zu erklären. Dies gilt schon deshalb, weil die Variation unter den Pluralformen wohl mit dazu beiträgt, dass trotz der Arbeiten von Mugdan 1977 und Köpcke 1987, 1993, der klaren Darstellung des Pluralsystems in vielen Grammatiken, z.B. Eisenberg 1986, 1989, 1998 noch immer bisweilen die Meinung besteht, die Pluralbildung im Deutschen sei arbiträr.Es soll gezeigt werden, dass das Pluralsystem des Deutschen nach Beschränkungen aufgebaut ist, die morphologischer und silbenphonologischer Natur sind und sich im Rahmen der Optimalitätstheorie (OT beschreiben lassen. Die OT nimmt an, dass Wortformen universalen Beschränkungen (Constraints unterliegen, und dass diese prinzipiell verletzbar sind. Ich werde zunächst die für die Pluralbildung relevanten Beschränkungen definieren, dann an heimischen Pluralformen und -varianten ihr Zusammenwirken zeigen und schließlich den Assimilationsprozess von Fremdwörtern mit Hilfe dieser Beschränkungen und der Beschränkungshierarchien zu erklären versuchen. Daran werden schließlich Überlegungen zu Verarbeitung und Lernbarkeit der Pluralformen geknüpft.

Medienerziehung im Vorschulbereich - Zum Projekt Mediengarten der Wiener Medienpädagogik

Directory of Open Access Journals (Sweden)

Gudrun Kern

2010-09-01

Full Text Available Im Zuge des Projekts Mediengarten der Wiener Medienpädagogik wurde in Kooperation mit angehenden KindergartenpädagogInnen eine Medienerziehung im Sinne einer Auseinandersetzung über Medien im Vorschulbereich anhand konkreter Angebote in Kindergärten konzipiert. Im folgenden Artikel werden die Schwerpunktsetzungen dieses Konzepts vorgestellt und durch praktische Beispiele verdeutlicht.

Cyberbullying und Empathie : affektive, kognitive und medienbasierte Empathie im Kontext von Cyberbullying im Kindes- und Jugendalter

OpenAIRE

Pfetsch, Jan; Müller, Christin R.; Ittel, Angela

2014-01-01

"Bei medial vermittelter Kommunikation sinkt sowohl die Hemmschwelle für aggressive Verhaltensweisen wie Cyberbullying als auch die Wahrscheinlichkeit empathischer Reaktionen. Im Fokus der vorliegenden Studie mit 979 Schülerinnen und Schülern der 4.-8. Klassen (M=12.01, SD=1.68 Jahre, 55% weiblich) stand die Frage, ob Cyberbullies geringere Ausprägungen für affektive, kognitive und medienbasierte Empathie aufweisen als Unbeteiligte. Empathie wurde im Selbst- und Peerbericht erhoben. Hypothese...

Long-Term Bending Creep Behavior of Thin-Walled CFRP Tendon Pretensioned Spun Concrete Poles

Directory of Open Access Journals (Sweden)

Giovanni P. Terrasi

2014-07-01

Full Text Available This paper discusses the long-term behavior of a series of highly-loaded, spun concrete pole specimens prestressed with carbon fiber-reinforced polymer (CFRP tendons, which were subjected to outdoor four-point bending creep tests since 1996 in the frame of collaboration with the Swiss precast concrete producer, SACAC (Società Anonima Cementi Armati Centrifugati. The 2 m span cylindrical beams studied are models for lighting poles produced for the last 10 years and sold on the European market. Five thin-walled pole specimens were investigated (diameter: 100 mm; wall-thickness: 25–27 mm. All specimens were produced in a pretensioning and spinning technique and were prestressed by pultruded CFRP tendons. Initially, two reference pole specimens were tested in quasi-static four-point bending to determine the short-term failure moment and to model the short-term flexural behavior. Then, three pole specimens were loaded to different bending creep moments: while the lowest loaded specimen was initially uncracked, the second specimen was loaded with 50% of the short-term bending failure moment and exhibited cracking immediately after load introduction. The highest loaded pole specimen sustained a bending moment of 72% of the short-term bending failure moment for 16.5 years before failing in July 2013, due to the bond failure of the tendons, which led to local crushing of the high-performance spun concrete (HPSC. Besides this, long-term monitoring of the creep tests has shown a limited time- and temperature-dependent increase of the deflections over the years, mainly due to the creep of the concrete. A concrete creep-based model allowed for the calculation of the long-term bending curvatures with reasonable accuracy. Furthermore, the pole specimens showed crack patterns that were stable over time and minimal slippage of the tendons with respect to the pole’s end-faces for the two lower load levels. The latter proves the successful and durable

As cast precipitation microstructures in twin-roller melt-spun Cu{sub 90}Co{sub 10} alloys

Energy Technology Data Exchange (ETDEWEB)

Núñez-Coavas, H. [Facultad de Matemática, Astronomía y Física, Universidad Nacional de Córdoba, Ciudad Universitaria, 5000 Córdoba (Argentina); Pozo-López, G., E-mail: gpozo@famaf.unc.edu.ar [Facultad de Matemática, Astronomía y Física, Universidad Nacional de Córdoba, Ciudad Universitaria, 5000 Córdoba (Argentina); Consejo Nacional de Investigaciones Científicas y Técnicas (CONICET) (Argentina); Instituto de Física Enrique Gaviola – CONICET (Argentina); Condó, A.M. [Consejo Nacional de Investigaciones Científicas y Técnicas (CONICET) (Argentina); Centro Atómico Bariloche, Comisión Nacional de Energía Atómica, Instituto Balseiro, Universidad Nacional de Cuyo, Av. Bustillo 9500, 8400 San Carlos de Bariloche (Argentina); Urreta, S.E. [Facultad de Matemática, Astronomía y Física, Universidad Nacional de Córdoba, Ciudad Universitaria, 5000 Córdoba (Argentina); and others

2016-12-15

As cast Cu{sub 90}Co{sub 10} ribbons rapidly solidified by twin-roller melt spinning, exhibit special microstructure features. This processing method provides scenarios where a different phase selection takes place; coherent Co precipitates form directly from solidification, with neither a spinodal-like composition oscillation nor a discontinuously precipitated laminar phase. Samples are processed at tangential wheel speeds of 10 m/s (V10), 15 m/s (V15), 20 m/s (V20) and 30 m/s (V30). Microstructures resulting from this single step process are characterized and the hysteresis properties and the magnetoresistance effects evaluated. Samples V30 have a quite uniform density of coherent precipitates, with a narrow size distribution around 4 nm. On contrary, non-uniform precipitate distributions are found in samples cooled at lower rates; zones with a high density of coherent Co-rich precipitates are found forming colonies. These colonies are consistent with the extended compositional fluctuations occurring during very early stages in the cooling process. Samples may exhibit wide (V10) and even bimodal (V15) size distributions. Only samples V30 behave close to the ideal superparamagnetism. Samples V20 present relatively large coercivity and relative remanence and behave as an interacting superparamagnet, while the hysteresis loops of ribbons cooled at lower rates exhibit a ferromagnetic contribution in addition to the superparamagnetic-like one. This ferromagnetic component arises from blocked precipitates, larger than the upper bound size for superparamagnetic behavior at 300 K (12 nm). Room temperature magnetoresistance values associated to granular scattering units decrease as the mean precipitate size increases, but they remain below 2%, which is lower than that measured in samples annealed after rapid solidification, indicating that in this latter case contributions from the spinodally segregated matrix take place in addition to that of Co granules. - Highlights: �

Automated Fiber Placement of PEEK/IM7 Composites with Film Interleaf Layers

Science.gov (United States)

Hulcher, A. Bruce; Banks, William I., III; Pipes, R. Byron; Tiwari, Surendra N.; Cano, Roberto J.; Johnston, Norman J.; Clinton, R. G., Jr. (Technical Monitor)

2001-01-01

The incorporation of thin discrete layers of resin between plies (interleafing) has been shown to improve fatigue and impact properties of structural composite materials. Furthermore, interleafing could be used to increase the barrier properties of composites used as structural materials for cryogenic propellant storage. In this work, robotic heated-head tape placement of PEEK/IM7 composites containing a PEEK polymer film interleaf was investigated. These experiments were carried out at the NASA Langley Research Center automated fiber placement facility. Using the robotic equipment, an optimal fabrication process was developed for the composite without the interleaf. Preliminary interleaf processing trials indicated that a two-stage process was necessary; the film had to be tacked to the partially-placed laminate then fully melted in a separate operation. Screening experiments determined the relative influence of the various robotic process variables on the peel strength of the film-composite interface. Optimization studies were performed in which peel specimens were fabricated at various compaction loads and roller temperatures at each of three film melt processing rates. The resulting data were fitted with quadratic response surfaces. Additional specimens were fabricated at placement parameters predicted by the response surface models to yield high peel strength in an attempt to gage the accuracy of the predicted response and assess the repeatability of the process. The overall results indicate that quality PEEK/lM7 laminates having film interleaves can be successfully and repeatability fabricated by heated head automated fiber placement.

Integrated hot-melt extrusion - injection molding continuous tablet manufacturing platform: Effects of critical process parameters and formulation attributes on product robustness and dimensional stability.

Science.gov (United States)

Desai, Parind M; Hogan, Rachael C; Brancazio, David; Puri, Vibha; Jensen, Keith D; Chun, Jung-Hoon; Myerson, Allan S; Trout, Bernhardt L

2017-10-05

This study provides a framework for robust tablet development using an integrated hot-melt extrusion-injection molding (IM) continuous manufacturing platform. Griseofulvin, maltodextrin, xylitol and lactose were employed as drug, carrier, plasticizer and reinforcing agent respectively. A pre-blended drug-excipient mixture was fed from a loss-in-weight feeder to a twin-screw extruder. The extrudate was subsequently injected directly into the integrated IM unit and molded into tablets. Tablets were stored in different storage conditions up to 20 weeks to monitor physical stability and were evaluated by polarized light microscopy, DSC, SEM, XRD and dissolution analysis. Optimized injection pressure provided robust tablet formulations. Tablets manufactured at low and high injection pressures exhibited the flaws of sink marks and flashing respectively. Higher solidification temperature during IM process reduced the thermal induced residual stress and prevented chipping and cracking issues. Polarized light microscopy revealed a homogeneous dispersion of crystalline griseofulvin in an amorphous matrix. DSC underpinned the effect of high tablet residual moisture on maltodextrin-xylitol phase separation that resulted in dimensional instability. Tablets with low residual moisture demonstrated long term dimensional stability. This study serves as a model for IM tablet formulations for mechanistic understanding of critical process parameters and formulation attributes required for optimal product performance. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of rare-earth elements on nanophase evolution, crystallization ...

Indian Academy of Sciences (India)

scattered image of Al87Ni8La5 ingot, the phases are marked. Figure 2. XRD patterns of as-melt-spun Al–Ni–RE amorphous ribbons on the air-cooled side. temperature axis change with alloy composition. Two or three exothermic peaks.

Instrumentale Spielformeln und Vokale Verzierungen im 16.Jahrhundert

Directory of Open Access Journals (Sweden)

Göllner, Theodor

2001-12-01

Full Text Available In the music of the 16th century, stereotype four-note formulas are found in the instrumental as well as in the vocal idiom. Although frequently identical in appearance, their functions are very different. While indispensable in the instrumental idiom, particularly in keyboard music, where they represent the very essence of instruction in 15th-century organ treatises and fundamenta, they appear in vocal music only as additions to finished compositions or existing practices. What amounts to an absolute necessity in one case is merely an ornamental supplement in the other. In vocal music it is treated as a matter of performance carried out by a qualified soloist and limited to the musical centers of Italy. The present article raises the question as to how the genuinely instrumental and widely spread keyboard practice made its impact on the vocal ornaments of the singer, whose primary concern is the musical communication of language.

[de] Die in der Musik des 16. Jahrhunderts im Instrumentalen wie im Vokalen vorkommenden, meist viertönigen, stereotypen Formeln sind zwar in beiden Bereichen weitgehend identisch, doch von höchst unterschiedlicher Funktion. Während sie im Instrumentalen, besonders in der Tastenmusik, unverzichtbar sind und schon im 15. Jahrhundert den Kern der Orgeltraktate und Fundamenta bilden, treten sie im Vokalen zu einer fertigen Komposition oder bestehenden Praxis hinzu. Was im einen Fall eine unbedingte Notwendigkeit ist, wird im anderen zu einem nachträglichen Ornament, das sich oft erst bei der Aufftührung einstellt, den qualifizierten Solosänger voraussetzt und auf die musikalischen Zentren Italiens konzentriert war. Der Artikel versucht zu klären, wie sich das genuin instrumentale, allgemein verbreitete Tastenspiel auf die spezielle Verzierungskunst des Sängers auswirkt, dessen primäre Aufgabe es ist, Sprache musikalisch zu vermitteln.

Development of a plug-type IMS-MS instrument and its applications in resolving problems existing in in-situ detection of illicit drugs and explosives by IMS.

Science.gov (United States)

Du, Zhenxia; Sun, Tangqiang; Zhao, Jianan; Wang, Di; Zhang, Zhongxia; Yu, Wenlian

2018-07-01

Ion mobility spectrometry (IMS) which acts as a rapid analysis technique is widely used in the field detection of illicit drugs and explosives. Due to limited separation abilities of the pint-sized IMS challenges and problems still exist regarding high false positive and false negative responses due to the interference of the matrix. In addition, the gas-phase ion chemistry and special phenomena in the IMS spectra, such one substance showing two peaks, were not identified unambiguously. In order to explain or resolve these questions, in this paper, an ion mobility spectrometry was coupled to a mass spectrometry (IMS-MS). A commercial IMS is embedded in a custom-built ion chamber shell was attached to the mass spectrometer. The faraday plate of IMS was fabricated with a hole for the ions to passing through to the mass spectrometer. The ion transmission efficiency of IMS-MS was optimized by optimizing the various parameters, especially the distance between the faraday plate and the cone of mass spectrum. This design keeps the integrity of the two original instruments and the mass spectrometry still works with multimode ionization source (i.e., IMS-MS, ESI-MS, APCI-MS modes). The illicit drugs and explosive samples were analyzed by the IMS-MS with 63 Ni source. The results showed that the IMS-MS is of high sensitivity. The ionization mechanism of the illicit drug and explosive samples with 63 Ni source were systematically studied. In addition, the interferent which interfered the detection of cocaine was identified as dibutyl phthalate (DBP) by this platform. The reason why the acetone solution of amphetamine showed two peaks was explained. Copyright © 2018 Elsevier B.V. All rights reserved.

Evaluation of Melt Behavior with initial Melt Velocity under SFR Severe Accidents

Energy Technology Data Exchange (ETDEWEB)

Heo, Hyo; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of); Jerng, Dong Wook [Chung-Ang Univ, Seoul (Korea, Republic of)

2015-10-15

In the current Korean sodium-cooled fast reactor (SFR) program, early dispersion of the molten metallic fuel within a subchannel is suggested as one of the inherent safety strategies for the initiating phase of hypothetical core disruptive accident (HCDA). The safety strategy provides negative reactivity driven by the melt dispersal, so it could reduce the possibility of the recriticality event under a severe triple or more fault scenario for SFR. Since the behavior of the melt dispersion is unpredictable, it depends on the accident condition, particularly core region. While the voided coolant channel region is usually developed in the inner core, the unvoided coolant channel region is formed in the outer core. It is important to confirm the fuel dispersion with the core region, but there are not sufficient existing studies for them. From the existing studies, the coolant vapor pressure is considered as one of driving force to move the melt towards outside of the core. There is a complexity of the phenomena during intermixing of the melt with the coolant after the horizontal melt injections. It is too difficult to understand the several combined mechanisms related to the melt dispersion and the fragmentation. Thus, it could be worthwhile to study the horizontal melt injections at lower temperature as a preliminary study in order to identify the melt dispersion phenomena. For this reason, it is required to clarify whether the coolant vapor pressure is the driving force of the melt dispersion with the core region. The specific conditions to be well dispersed for the molten metallic fuel were discussed in the experiments with the simulant materials. The each melt behavior was compared to evaluate the melt dispersion under the coolant void condition and the boiling condition. As the results, the following results are remarked: 1. The upward melt dispersion did not occur for a given melt and coolant temperature in the nonboiling range. Over current range of conditions

Evaluation of Melt Behavior with initial Melt Velocity under SFR Severe Accidents

International Nuclear Information System (INIS)

Heo, Hyo; Bang, In Cheol; Jerng, Dong Wook

2015-01-01

In the current Korean sodium-cooled fast reactor (SFR) program, early dispersion of the molten metallic fuel within a subchannel is suggested as one of the inherent safety strategies for the initiating phase of hypothetical core disruptive accident (HCDA). The safety strategy provides negative reactivity driven by the melt dispersal, so it could reduce the possibility of the recriticality event under a severe triple or more fault scenario for SFR. Since the behavior of the melt dispersion is unpredictable, it depends on the accident condition, particularly core region. While the voided coolant channel region is usually developed in the inner core, the unvoided coolant channel region is formed in the outer core. It is important to confirm the fuel dispersion with the core region, but there are not sufficient existing studies for them. From the existing studies, the coolant vapor pressure is considered as one of driving force to move the melt towards outside of the core. There is a complexity of the phenomena during intermixing of the melt with the coolant after the horizontal melt injections. It is too difficult to understand the several combined mechanisms related to the melt dispersion and the fragmentation. Thus, it could be worthwhile to study the horizontal melt injections at lower temperature as a preliminary study in order to identify the melt dispersion phenomena. For this reason, it is required to clarify whether the coolant vapor pressure is the driving force of the melt dispersion with the core region. The specific conditions to be well dispersed for the molten metallic fuel were discussed in the experiments with the simulant materials. The each melt behavior was compared to evaluate the melt dispersion under the coolant void condition and the boiling condition. As the results, the following results are remarked: 1. The upward melt dispersion did not occur for a given melt and coolant temperature in the nonboiling range. Over current range of conditions

IMS applications analysis

Energy Technology Data Exchange (ETDEWEB)

RODACY,PHILIP J.; REBER,STEPHEN D.; SIMONSON,ROBERT J.; HANCE,BRADLEY G.

2000-03-01

This report examines the market potential of a miniature, hand-held Ion Mobility Spectrometer. Military and civilian markets are discussed, as well as applications in a variety of diverse fields. The strengths and weaknesses of competing technologies are discussed. An extensive Ion Mobility Spectrometry (IMS) bibliography is included. The conclusions drawn from this study are: (1) There are a number of competing technologies that are capable of detecting explosives, drugs, biological, or chemical agents. The IMS system currently represents the best available compromise regarding sensitivity, specificity, and portability. (2) The military market is not as large as the commercial market, but the military services are more likely to invest R and D funds in the system. (3) Military applications should be addressed before commercial applications are addressed. (4) There is potentially a large commercial market for rugged, hand-held Ion Mobility Spectrometer systems. Commercial users typically do not invest R and D funds in this type of equipment rather, they wait for off-the-shelf availability.

A Management Tool for Improvement (Improving) IMS Stations Performance

International Nuclear Information System (INIS)

Mohammad, D.; Pantin, A.; Quintana, E.

2011-01-01

IMS-Maintenance is a software under development by the personnel of ARN-CTBT office, intended for the technical management of IMS stations under ARN's responsibility. This software integrates the whole control of the equipment in an IMS station, including the management of consumables used in daily or periodic operation. It permits an easy retrieval (access) of the technical features, suppliers, etc. of each item of the equipment, as well as its maintenance history and scheduled task. Although this project is still in a starting phase, a preliminary version of this software is being used in radionuclide station RN01 (Buenos Aires), having already demonstrated its usefulness and potential for the improvement of IMS station management. (authors)

A Review of the Effect of Processing Variables on the Fabrication of Electro spun Nano fibers for Drug Delivery Applications

International Nuclear Information System (INIS)

Pillay, V.; Dott, C.; Choonara, Y.E.; Tyagi, Ch.; Tomar, L.; Kumar, P.; Toit, L.C.D.; Ndesendo, V.M.K.

2013-01-01

Electro spinning is a fast emerging technique for producing ultrafine fibers by utilizing electrostatic repulsive forces. The technique has gathered much attention due to the emergence of nano technology that sparked worldwide research interest in nano materials for their preparation and application in biomedicine and drug delivery. Electro spinning is a simple, adaptable, cost-effective, and versatile technique for producing nano fibers. For effective and efficient use of the technique, several processing parameters need to be optimized for fabricating polymeric nano fibers. The nano fiber morphology, size, porosity, surface area, and topography can be refined by varying these parameters. Such flexibility and diversity in nano fiber fabrication by electro spinning has broadened the horizons for widespread application of nano fibers in the areas of drug and gene delivery, wound dressing, and tissue engineering. Drug-loaded electro spun nano fibers have been used in implants, transdermal systems, wound dressings, and as devices for aiding the prevention of post surgical abdominal adhesions and infection. They show great promise for use in drug delivery provided that one can confidently control the processing variables during fabrication. This paper provides a concise incursion into the application of electro spun nano fibers in drug delivery and cites pertinent processing parameters that may influence the performance of the nano fibers when applied to drug delivery.

Radiological information management system (RadIMS)

International Nuclear Information System (INIS)

Oesterling, R.G.; Marko, S.A.; Tschaeche, A.N.

1991-01-01

Westinghouse Idaho Nuclear Company, Inc. (WINCO) is developing and implementing an information management system, known as RadIMS, to track and record personnel exposure to ionizing radiation. RadIMS has been designed to fulfill all the requirements of US Department of Energy (USDOE) Order 5480.11, ''Radiation Protection for Occupational Workers.'' This Order requires the contractor to maintain detailed radiation exposure records on all individuals who work at the facility. These records must be retrievable for the entire working life of the individual and be available to other USDOE contractors on request. To meet these general needs, RadIMS provides for retrieval of detailed, comprehensive individual exposure histories as well as the usual online interactions to accomplish day-today radiation protection operations. These two extremes of functionality require different approaches in the WINCO computing environment. The exposure histories include database text, paper, microfilm, and electronic bitmaps

Radiological information management system (RadIMS)

Energy Technology Data Exchange (ETDEWEB)

Oesterling, R.G.; Marko, S.A.; Tschaeche, A.N.

1991-08-19

Westinghouse Idaho Nuclear Company, Inc. (WINCO) is developing and implementing an information management system, known as RadIMS, to track and record personnel exposure to ionizing radiation. RadIMS has been designed to fulfill all the requirements of US Department of Energy (USDOE) Order 5480.11, Radiation Protection for Occupational Workers.'' This Order requires the contractor to maintain detailed radiation exposure records on all individuals who work at the facility. These records must be retrievable for the entire working life of the individual and be available to other USDOE contractors on request. To meet these general needs, RadIMS provides for retrieval of detailed, comprehensive individual exposure histories as well as the usual online interactions to accomplish day-today radiation protection operations. These two extremes of functionality require different approaches in the WINCO computing environment. The exposure histories include database text, paper, microfilm, and electronic bitmaps.

Radiological information management system (RadIMS)

Energy Technology Data Exchange (ETDEWEB)

Oesterling, R.G.; Marko, S.A.; Tschaeche, A.N.

1991-08-19

Westinghouse Idaho Nuclear Company, Inc. (WINCO) is developing and implementing an information management system, known as RadIMS, to track and record personnel exposure to ionizing radiation. RadIMS has been designed to fulfill all the requirements of US Department of Energy (USDOE) Order 5480.11, ``Radiation Protection for Occupational Workers.`` This Order requires the contractor to maintain detailed radiation exposure records on all individuals who work at the facility. These records must be retrievable for the entire working life of the individual and be available to other USDOE contractors on request. To meet these general needs, RadIMS provides for retrieval of detailed, comprehensive individual exposure histories as well as the usual online interactions to accomplish day-today radiation protection operations. These two extremes of functionality require different approaches in the WINCO computing environment. The exposure histories include database text, paper, microfilm, and electronic bitmaps.

Designing new biocompatible glass-forming Ti75-x Zr10 Nbx Si15 (x = 0, 15) alloys: corrosion, passivity, and apatite formation.

Science.gov (United States)

Abdi, Somayeh; Oswald, Steffen; Gostin, Petre Flaviu; Helth, Arne; Sort, Jordi; Baró, Maria Dolors; Calin, Mariana; Schultz, Ludwig; Eckert, Jürgen; Gebert, Annett

2016-01-01

Glass-forming Ti-based alloys are considered as potential new materials for implant applications. Ti75 Zr10 Si15 and Ti60 Zr10 Nb15 Si15 alloys (free of cytotoxic elements) can be produced as melt-spun ribbons with glassy matrix and embedded single β-type nanocrystals. The corrosion and passivation behavior of these alloys in their homogenized melt-spun states have been investigated in Ringer solution at 37°C in comparison to their cast multiphase crystalline counterparts and to cp-Ti and β-type Ti-40Nb. All tested materials showed very low corrosion rates as expressed in corrosion current densities icorr  alloys passive states in a wide potential range. This corresponds to low passive current densities ipass  = 2 ± 1 µA/cm(2) based on the growth of oxide films with thickness d alloys is beneficial for stable surface passivity. The addition of Nb does not only improve the glass-forming ability and the mechanical properties but also supports a high pitting resistance even at extreme anodic polarization up to 4V versus SCE were oxide thickness values of d ∼35 nm are reached. With regard to the corrosion properties, the Nb-containing nearly single-phase glassy alloy can compete with the β-type Ti-40Nb alloy. SBF tests confirmed the ability for formation of hydroxyapatite on the melt-spun alloy surfaces. All these properties recommend the new glass-forming alloys for application as wear- and corrosion-resistant coating materials for implants. © 2015 Wiley Periodicals, Inc.

Rapakivi texture formation via disequilibrium melting in a contact partial melt zone, Antarctica

Science.gov (United States)

Currier, R. M.

2017-12-01

In the McMurdo Dry Valleys of Antarctica, a Jurassic aged dolerite sill induced partial melting of granite in the shallow crust. The melt zone can be traced in full, from high degrees of melting (>60%) along the dolerite contact, to no apparent signs of melting, 10s of meters above the contact. Within this melt zone, the well-known rapakivi texture is found, arrested in various stages of development. High above the contact, and at low degrees of melting, K-feldspar crystals are slightly rounded and unmantled. In the lower half of the melt zone, mantles of cellular textured plagioclase appear on K-feldspar, and thicken towards the contact heat source. At the highest degrees of melting, cellular-textured plagioclase completely replaces restitic K-feldspar. Because of the complete exposure and intact context, the leading models of rapakivi texture formation can be tested against this system. The previously proposed mechanisms of subisothermal decompression, magma-mixing, and hydrothermal exsolution all fail to adequately describe rapakivi generation in this melt zone. Preferred here is a closed system model that invokes the production of a heterogeneous, disequilibrium melt through rapid heating, followed by calcium and sodium rich melt reacting in a peritectic fashion with restitic K-feldspar crystals. This peritectic reaction results in the production of plagioclase of andesine-oligoclase composition—which is consistent with not just mantles in the melt zone, but globally as well. The thickness of the mantle is diffusion limited, and thus a measure of the diffusive length scale of sodium and calcium over the time scale of melting. Thermal modeling provides a time scale of melting that is consistent with the thickness of observed mantles. Lastly, the distribution of mantled feldspars is highly ordered in this melt zone, but if it were mobilized and homogenized—mixing together cellular plagioclase, mantled feldspars, and unmantled feldspars—the result would be

The future of the IMS Learning Design specification: a critical look

NARCIS (Netherlands)

Sloep, Peter

2009-01-01

P. B. Sloep (2009). The future of the IMS Learning Design specification: a critical look. Presentation at the IMS Learning Design seminar 'The future of IMS Learning Design'. December, 10, 2009, Wollongong, Australia: University of Wollongong.

Experimental results for TiO2 melting and release using cold crucible melting

International Nuclear Information System (INIS)

Hong, S. W.; Min, B. T.; Park, I. G.; Kim, H. D.

2000-01-01

To simulate the severe accident phenomena using the real reactor material which melting point is about 2,800K, the melting and release method for materials with high melting point should be developed. This paper discusses the test results for TiO 2 materials using the cold crucible melting method to study the melting and release method of actual corium. To melt and release of few kg of TiO2, the experimental facility is manufactured through proper selection of design parameters such as frequency and capacity of R.F generator, crucible size and capacity of coolant. The melting and release of TiO 2 has been successfully performed in the cold crucible of 15cm in inner diameter and 30cm in height with 30kW RF power generator of 370 KHz. In the melt delivery experiment, about 2.6kg of molten TiO2, 60% of initial charged mass, is released. Rest of it is remained in the watercage in form of the rubble crust formed at the top of crucible and melt crust formed at the interface between the water-cage and melt. Especially, in the melt release test, the location of the working coil is important to make the thin crust at the bottom of the crucible

Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Melting Efficiency Improvement

Energy Technology Data Exchange (ETDEWEB)

Principal Investigator Kent Peaslee; Co-PI’s: Von Richards, Jeffrey Smith

2012-07-31

Steel foundries melt recycled scrap in electric furnaces and typically consume 35-100% excess energy from the theoretical energy requirement required to pour metal castings. This excess melting energy is multiplied by yield losses during casting and finishing operations resulting in the embodied energy in a cast product typically being three to six times the theoretical energy requirement. The purpose of this research project was to study steel foundry melting operations to understand energy use and requirements for casting operations, define variations in energy consumption, determine technologies and practices that are successful in reducing melting energy and develop new melting techniques and tools to improve the energy efficiency of melting in steel foundry operations.

Im Wind / Mari Vallisoo ; tõlk. Gisbert Jänicke

Index Scriptorium Estoniae

Vallisoo, Mari, 1950-2013

2003-01-01

Sisu: Im Wind = Tuulega ; Zwei Frauen = Kaks naist ; In Gedanken an Aleksander Levin = aleksander Levinile mõteldes ; Jetzt im Dunkel = Nüüd pimedas ; Fragen = Küsimused ; Der Zwillingsbruder = Kaksikvend

MELT-IIIB: an updated version of the melt code

International Nuclear Information System (INIS)

Tabb, K.K.; Lewis, C.H.; O'Dell, L.D.; Padilla, A. Jr.; Smith, D.E.; Wilburn, N.P.

1979-04-01

The MELT series is a reactor modeling code designed to investigate a wide variety of hypothetical accident conditions, particularly the transient overpower sequence. MELT-IIIB is the latest in the series

Transplantate und Implantate im Mittelohrbereich - Teil 1 (Stand 2002)

Science.gov (United States)

Kempf, Hans-Georg; Lenarz, Thomas; Eckert, Karl-Ludwig

In Deutschland leben ungefähr 12 Millionen Menschen, die an einer ein- oder beidseitigen Schwerhörigkeit leiden. Diese kann angeboren oder im Laufe des Lebens erworben sein. Klinisch und therapeutisch wichtig ist die Unterscheidung, ob die Ursache der Schwerhörigkeit im Bereich des Mittelohres, d. h. der Schallübertragung, oder im Bereich des Innenohres, der Hörnerven und der zentralen Hörbahnabschnitte, d. h. der Schallempfindung, liegt. 2,5 Millionen Schwerhörige haben dabei das Problem der Schallübertragung, d.h. die Störung liegt im Mittelohrbereich, und hier kann man in der Regel mit operativen, mikrochirurgisch durchgeführten Massnahmen helfen [1, 2]. Im Vordergrund steht als Ursache hier die chronische Mittelohrentzündung, die sich als Perforation des Trommelfells, als Defekt oder Unterbrechung der Gehörknöchelchen oder auch als Cholesteatom, einer sogenannte Knocheneiterung äussern kann [3]. Therapeutisch und damit als Prinzip der operativen Hörverbesserung steht primär der Verschluss des Trommelfells oder eine Rekonstruktion der Gehörknöchelchen an.

Coherent ambient infrasound recorded by the global IMS network

Science.gov (United States)

Matoza, R. S.; Landes, M.; Le Pichon, A.; Ceranna, L.; Brown, D.

2011-12-01

The International Monitoring System (IMS) includes a global network of infrasound arrays, which is designed to detect atmospheric nuclear explosions anywhere on the planet. The infrasound network also has potential application in detection of natural hazards such as large volcanic explosions and severe weather. Ambient noise recorded by the network includes incoherent wind noise and coherent infrasound. We present a statistical analysis of coherent infrasound recorded by the IMS network. We have applied broadband (0.01 to 5 Hz) array processing systematically to the multi-year IMS historical dataset (2005-present) using an implementation of the Progressive Multi-Channel Correlation (PMCC) algorithm in log-frequency space. We show that IMS arrays consistently record coherent ambient infrasound across the broad frequency range from 0.01 to 5 Hz when wind-noise levels permit. Multi-year averaging of PMCC detection bulletins emphasizes continuous signals such as oceanic microbaroms, as well as persistent transient signals such as repetitive volcanic, surf, or anthropogenic activity (e.g., mining or industrial activity). While many of these continuous or repetitive signals are of interest in their own right, they may dominate IMS array detection bulletins and obscure or complicate detection of specific signals of interest. The new PMCC detection bulletins have numerous further applications, including in volcano and microbarom studies, and in IMS data quality assessment.

Gruppenbezogene Menschenfeindlichkeit im Sport in Sachsen-Anhalt

OpenAIRE

Delto, Hannes; Tzschoppe, Petra

2016-01-01

Mit der Querschnittsstudie „Wir und die Anderen – Gruppenbezogene Menschenfeindlichkeit im organisierten Sport in Sachsen-Anhalt“ wurde das Syndrom Gruppenbezogener Menschenfeindlichkeit im organisierten Sport untersucht. Das Konzept der Gruppenbezogenen Menschenfeindlichkeit – ausgehend von einer Ideologie der Ungleichwertigkeit – wurde von Prof. Wilhelm Heitmeyer (Universität Bielefeld) entwickelt. Die Ergebnisse ermöglichen explizite Aussagen über Ausmaß und Ursachen Gruppenbezogener Mensc...

Cloud screening and melt water detection over melting sea ice using AATSR/SLSTR

Science.gov (United States)

Istomina, Larysa; Heygster, Georg

2014-05-01

With the onset of melt in the Arctic Ocean, the fraction of melt water on sea ice, the melt pond fraction, increases. The consequences are: the reduced albedo of sea ice, increased transmittance of sea ice and affected heat balance of the system with more heat passing through the ice into the ocean, which facilitates further melting. The onset of melt, duration of melt season and melt pond fraction are good indicators of the climate state of the Arctic and its change. In the absence of reliable sea ice thickness retrievals in summer, melt pond fraction retrieval from satellite is in demand as input for GCM as an indicator of melt state of the sea ice. The retrieval of melt pond fraction with a moderate resolution radiometer as AATSR is, however, a non-trivial task due to a variety of subpixel surface types with very different optical properties, which give non-unique combinations if mixed. In this work this has been solved by employing additional information on the surface and air temperature of the pixel. In the current work, a concept of melt pond detection on sea ice is presented. The basis of the retrieval is the sensitivity of AATSR reflectance channels 550nm and 860nm to the amount of melt water on sea ice. The retrieval features extensive usage of a database of in situ surface albedo spectra. A tree of decisions is employed to select the feasible family of in situ spectra for the retrieval, depending on the melt stage of the surface. Reanalysis air temperature at the surface and brightness temperature measured by the satellite sensor are analyzed in order to evaluate the melting status of the surface. Case studies for FYI and MYI show plausible retrieved melt pond fractions, characteristic for both of the ice types. The developed retrieval can be used to process the historical AATSR (2002-2012) dataset, as well as for the SLSTR sensor onboard the future Sentinel-3 mission (scheduled for launch in 2015), to keep the continuity and obtain longer time sequence

Freie Lerninhalte im Internet mit Studierenden recherchieren, kommentieren und kompilieren. Zur Gestaltung der online-Selbstlernangebote im hr-Funkkolleg Philosophie

Directory of Open Access Journals (Sweden)

Jakob Krebs

2017-03-01

Full Text Available Wie lassen sich online frei verfügbare Bildungsinhalte mit Studierenden so zusammenstellen, dass sie als thematisch sortierte Selbstlernmaterialien unkompliziert gefunden werden können – sei es von anderen Studierenden, interessierten Laien oder auch von Lehrkräften in Bildungsinstitutionen? Der vorliegende Werkstattbericht rekonstruiert ein Lernszenario, in dem Studierende vorhandene Materialien im Internet recherchierten, kommentierten und kompilierten, um ein Online-Zusatzangebot zu den Radiosendungen im hr-Funkkolleg Philosophie 2014/15 zu erstellen. Die Rahmenbedingungen dieser ungewöhnlichen universitären Kooperation mit dem Rundfunk werden im ersten Abschnitt vorgestellt. Der zweite Abschnitt skizziert das didaktische Design zusammen mit dem Projektstrukturplan eines produktorientierten kollaborativen Lernsettings mit Wiki-Einsatz. Im dritten Abschnitt werden der Lernerfolg bei den Studierenden sowie einige Herausforderungen benannt, die u. a. in der Abschlussevaluierung zur Sprache kamen. Der vierte Abschnitt macht die Projekterfahrungen für reguläre Lehr- und Lern-Szenarien fruchtbar, in denen nicht nur Studierende mit didaktischen Interessen durch die gemeinsame Gestaltung von Internetangeboten fachlich und methodisch profitieren können. Mit dem Bericht wird somit u. a. veranschaulicht, wie sich Ansätze von Blended, Peer-Assisted und Service Learning produktiv kombinieren lassen.

Effect of Lowering Twist Levels on Quality Parameters of Rotor Spun Cotton Yarn

Directory of Open Access Journals (Sweden)

FAROOQ AHMED

2016-07-01

Full Text Available Investigations were made to explore the influence of lowering twist level on quality characteristics of rotor spun yarn. Three levels of yarn linear density (i.e. 40, 35 and 30 tex and five levels of twist (i.e. 700, 600, 550, 500, and 450 were employed during yarn spinning trials. Each twist multiple was investigated at all linear densities for tensile strength, elongation, total CVm (Coefficient of Mass Variation imperfection index and hairiness. 100% cotton yarn samples were prepared on Reiter R-40 at rotor speed of 90,000 rpm. Determination of elongation, yarn strength, hairiness, mass variation, and total imperfections index was carried out on Uster Tensorapid-4 and Uster Tester-4 as per set standards of ISO standard test methods. Based on investigations it is established that yarn strength and elongation declined minutely (Insignificant with lowering twist levels but still can be confidently used for knitting yarns. However, significant improvement in total imperfection index and marginal enhancement in CVm were experienced.

Sulfur in zircons: A new window into melt chemistry

Science.gov (United States)

Tang, H.; Bell, E. A.; Boehnke, P.; Barboni, M.; Harrison, T. M.

2017-12-01

The abundance and isotopic composition of sulfur are important tools for exploring the photochemistry of the atmosphere, the thermal history of mantle and igneous rocks, and ancient metabolic processes on the early Earth. Because the oldest terrestrial samples are zircons, we developed a new in-situ procedure to analyze the sulfur content of zircons using the CAMECA ims 1290 at UCLA. We analyzed zircons from three metaluminous/I-type granites (reduced and oxidized Peninsular range and Elba), which exhibit low sulfur abundance with the average of 0.5ppm, and one peraluminous/S-type zircon (Strathbogie Range), which shows an elevated sulfur level with the average of 1.5ppm. Additionally, we found that sulfur content ranges between 0.4 and 2.3 ppm in young volcanic zircons (St. Lucia). Our analyses of zircons from the Jack Hills, Western Australia, whose ages range between 3.4 and 4.1 Ga, show a variety of sulfur contents. Three out of the ten zircons are consistent with the sulfur contents of S-type zircons; the rest have low sulfur contents, which are similar to those of I-type zircons. The high sulfur content in some of these Jack Hills zircons can be interpreted as indicating their origin in either a S-type granite or a volcanic reservoir. We favor the former interpretation since the Ti-in-zircon temperatures of our Jack Hills zircons is lower than those of volcanic zircons. Future work will be undertaken to develop a systematic understanding of the relationship between melt volatile content, melt chemistry, and zircon sulfur content.

Thermische Verletzungen im Kindesalter: Eine retrospektive Kohortenstudie von 212 Fällen

OpenAIRE

Sperling, Patrik Leonhart

2012-01-01

Anhand einer retrospektiven Datenanalyse sollen Verteilungsmuster von Verbrennungen und Verbrühungen bezogen auf Alter und Geschlecht untersucht werden. Erfasst wurden 212 Patienten im Alter von 0 bis 16 Jahren betrachtet, die im Zeitraum vom 01.01.2004 bis zum 31.12.2009 auf Grund einer thermischen Verletzung stationär im Universitätsklinikum Würzburg der Julius-Maximilians-Universität Würzburg behandelt wurden. Den größten Anteil thermischer Verletzungen im Kindesalter stellen Verbrühungen ...

Sequence-specific DNA alkylation by tandem Py-Im polyamide conjugates.

Science.gov (United States)

Taylor, Rhys Dylan; Kawamoto, Yusuke; Hashiya, Kaori; Bando, Toshikazu; Sugiyama, Hiroshi

2014-09-01

Tandem N-methylpyrrole-N-methylimidazole (Py-Im) polyamides with good sequence-specific DNA-alkylating activities have been designed and synthesized. Three alkylating tandem Py-Im polyamides with different linkers, which each contained the same moiety for the recognition of a 10 bp DNA sequence, were evaluated for their reactivity and selectivity by DNA alkylation, using high-resolution denaturing gel electrophoresis. All three conjugates displayed high reactivities for the target sequence. In particular, polyamide 1, which contained a β-alanine linker, displayed the most-selective sequence-specific alkylation towards the target 10 bp DNA sequence. The tandem Py-Im polyamide conjugates displayed greater sequence-specific DNA alkylation than conventional hairpin Py-Im polyamide conjugates (4 and 5). For further research, the design of tandem Py-Im polyamide conjugates could play an important role in targeting specific gene sequences. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Information Management System (Ims) For Gender Mainstreaming In ...

African Journals Online (AJOL)

Information Management System (IMS) is an essential tool in supporting the provision of information needed for planning and decision making in any organization. Proper IMS facilitates the smooth flow of information both vertical and horizontal. This paper presents the findings of a survey on information needs of the Gender ...

Effect of Ga substitution on the crystallization behaviour and glass forming ability of Zr-Al-Cu-Ni alloys

International Nuclear Information System (INIS)

Singh, Devinder; Yadav, T.P.; Mandal, R.K.; Tiwari, R.S.; Srivastava, O.N.

2010-01-01

The crystallization behaviour of melt spun Zr 69.5 Al 7.5-x Ga x Cu 12 Ni 11 (x = 0-7.5; in at.%) metallic glasses has been investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The DSC traces showed changes in crystallization behaviour with substitution of Ga. Formation of single nano-quasicrystalline phase by controlled crystallization of glasses has been found only for 0 ≤ x ≤ 1.5. Further increase of Ga content gives rise to formation of the quasicrystals together with Zr 2 Cu type crystalline phase. In addition to this, the substitution of Ga influences the size and shape of nano-quasicrystals. The glass forming abilities (GFAs) of these metallic glasses were assessed by the recognition of glass forming ability indicators, i.e. reduced glass transition temperature (T rg ) and supercooled liquid region (ΔT x ). The glass transition temperature (T g ) has been observed for all the melt spun ribbons.

Antibacterial performance of nano polypropylene filter media containing nano-TiO{sub 2} and clay particles

Energy Technology Data Exchange (ETDEWEB)

Shafiee, Sara; Zarrebini, Mohammad; Naghashzargar, Elham, E-mail: e.naghashzargar@tx.iut.ac.ir; Semnani, Dariush, E-mail: d-semnani@cc.iut.ac.ir [Isfahan University of Technology, Department of Textile Engineering (Iran, Islamic Republic of)

2015-10-15

Disinfection and elimination of pathogenic microorganisms from liquid can be achieved by filtration process using antibacterial filter media. The advent of nanotechnology has facilitated the introduction of membranes consisting of nano-fiber in filtration operations. The melt electro-spun fibers due to their extremely small diameters are used in the production of this particular filtration medium. In this work, antibacterial polypropylene filter medium containing clay particles and nano-TiO{sub 2} were made using melt electro-spun technology. Antibacterial performance of polypropylene nano-filters was evaluated using E. coli bacteria. Additionally, filtration efficiency of the samples in terms fiber diameter, filter porosity, and fiber distribution using image processing technique was determined. Air permeability and dust aerosol tests were conducted to establish the suitability of the samples as a filter medium. It was concluded that as far as antibacterial property is concerned, nano-fibers filter media containing clay particles are preferential to similar media containing TiO{sub 2} nanoparticles.

Calibración de imágenes de radares meteorológicos

Directory of Open Access Journals (Sweden)

Virgilio Santander Socorras Quintero

2014-04-01

Full Text Available En este documento se ilustran las técnicas de fusión de imágenes para complementar y calibrar la información meteorológica presente en imágenes de radares terrestres con el uso de imágenes satelitales meteorológicas. Para realizar la calibración de las imágenes de radares terrestres se implementó un método de fusión de imágenes basado en la herramienta matemática transformada wavelet discreta. Ya que existe una familia de wavelets, es necesario determinar cuál wavelet ofrece el mejor resultado; para esto se determina la correlación existente entre los resultados de fusión de diferentes wavelets y las imágenes uti-lizadas en cada fusión. Se define una metodología para selección de umbral global de segmentación y una metodología para realizar la calibración de las imágenes de radares terrestres. Siguiendo la metodología de calibración de imágenes, se generan algunos resultados y se muestran sus ventajas.

Melting of Dense Sodium

International Nuclear Information System (INIS)

Gregoryanz, Eugene; Degtyareva, Olga; Hemley, Russell J.; Mao, Ho-kwang; Somayazulu, Maddury

2005-01-01

High-pressure high-temperature synchrotron diffraction measurements reveal a maximum on the melting curve of Na in the bcc phase at ∼31 GPa and 1000 K and a steep decrease in melting temperature in its fcc phase. The results extend the melting curve by an order of magnitude up to 130 GPa. Above 103 GPa, Na crystallizes in a sequence of phases with complex structures with unusually low melting temperatures, reaching 300 K at 118 GPa, and an increased melting temperature is observed with further increases in pressure

A 2D double-porosity model for melting and melt migration beneath mid-oceanic ridges

Science.gov (United States)

Liu, B.; Liang, Y.; Parmentier, E.

2017-12-01

Several lines of evidence suggest that the melting and melt extraction region of the MORB mantle is heterogeneous consisting of an interconnected network of high permeability dunite channels in a low porosity harzburgite or lherzolite matrix. In principle, one can include channel formation into the tectonic-scale geodynamic models by solving conservation equations for a chemically reactive and viscously deformable porous medium. Such an approach eventually runs into computational limitations such as resolving fractal-like channels that have a spectrum of width. To better understand first order features of melting and melt-rock interaction beneath MOR, we have formulated a 2D double porosity model in which we treat the triangular melting region as two overlapping continua occupied by the low-porosity matrix and interconnected high-porosity channels. We use melt productivity derived from a thermodynamic model and melt suction rate to close our problem. We use a high-order accurate numerical method to solve the conservation equations in 2D for porosity, solid and melt velocities and concentrations of chemical tracers in the melting region. We carry out numerical simulations to systematically study effects of matrix-to-channel melt suction and spatially distributed channels on the distributions of porosity and trace element and isotopic ratios in the melting region. For near fractional melting with 10 vol% channel in the melting region, the flow field of the matrix melt follows closely to that of the solid because the small porosity (exchange between the melt and the solid. The smearing effect can be approximated by dispersion coefficient. For slowly diffusing trace elements (e.g., LREE and HFSE), the melt migration induced dispersion can be as effective as thermal diffusion. Therefore, sub-kilometer scale heterogeneities of Nd and Hf isotopes are significantly damped or homogenized in the melting region.

Energy Saving Melting and Revert Reduction Technology: Melting Efficiency in Die Casting Operations

Energy Technology Data Exchange (ETDEWEB)

David Schwam

2012-12-15

This project addressed multiple aspects of the aluminum melting and handling in die casting operations, with the objective of increasing the energy efficiency while improving the quality of the molten metal. The efficiency of melting has always played an important role in the profitability of aluminum die casting operations. Consequently, die casters need to make careful choices in selecting and operating melting equipment and procedures. The capital cost of new melting equipment with higher efficiency can sometimes be recovered relatively fast when it replaces old melting equipment with lower efficiency. Upgrades designed to improve energy efficiency of existing equipment may be well justified. Energy efficiency is however not the only factor in optimizing melting operations. Melt losses and metal quality are also very important. Selection of melting equipment has to take into consideration the specific conditions at the die casting shop such as availability of floor space, average quantity of metal used as well as the ability to supply more metal during peaks in demand. In all these cases, it is essential to make informed decisions based on the best available data.

Choosing the Right Free IM Providers and Clients for Your Library

Science.gov (United States)

Izenstark, Amanda K.

2009-01-01

With virtual library services increasing, public services librarians may find themselves with questions such as: What instant messaging services (IM) are available? Which IM service would best suit my patrons' needs? Which IM service best suits my library's technology profile? This column describes the features and functionality of major instant…

World-wide developments in motor vehicle inspection/maintenance (I/M) programs

Energy Technology Data Exchange (ETDEWEB)

Klausmeier, R. [Consulting Inc., Austin, TX (United States); Kishan, S. [Radian Corporation, Austin, TX (United States)

1995-12-31

Motor vehicles contribute much to urban air pollution. As a result, most governments have enacted emission standards that significantly lower pollutant emission levels from new motor vehicles. For example, vehicles built in the United States emit 95 % fewer pollutants than uncontrolled vehicles when they are new. However, studies indicate that proper maintenance is needed to obtain the full benefit of vehicle emission controls. Furthermore, there is evidence that a significant percentage of the vehicle fleet is not properly maintained. This has led to the creation of motor vehicle Inspection/Maintenance (I/M) Programs. I/M programs inspect vehicles for indications that they are emitting excessive quantities of pollutants. Vehicles that fail the inspection must be repaired in order to comply with program requirements. The first I/M programs were implemented in the United States in the early 1970s. With substantial urging from the federal government, most of the U.S. states with severe air pollution problems have implemented I/M programs. Recently, with the passage of the U.S. Clean Air Act Amendments of 1990, many states have been required to significantly upgrade the performance and coverage of their I/M programs. I/M programs also have been implemented in Europe and recently in Asia. This presentation reviews developments in I/M programs for light-duty gasoline powered vehicles. Developments in I/M programs for diesel powered vehicles are briefly described. (author)

World-wide developments in motor vehicle inspection/maintenance (I/M) programs

Energy Technology Data Exchange (ETDEWEB)

Klausmeier, R [Consulting Inc., Austin, TX (United States); Kishan, S [Radian Corporation, Austin, TX (United States)

1996-12-31

Motor vehicles contribute much to urban air pollution. As a result, most governments have enacted emission standards that significantly lower pollutant emission levels from new motor vehicles. For example, vehicles built in the United States emit 95 % fewer pollutants than uncontrolled vehicles when they are new. However, studies indicate that proper maintenance is needed to obtain the full benefit of vehicle emission controls. Furthermore, there is evidence that a significant percentage of the vehicle fleet is not properly maintained. This has led to the creation of motor vehicle Inspection/Maintenance (I/M) Programs. I/M programs inspect vehicles for indications that they are emitting excessive quantities of pollutants. Vehicles that fail the inspection must be repaired in order to comply with program requirements. The first I/M programs were implemented in the United States in the early 1970s. With substantial urging from the federal government, most of the U.S. states with severe air pollution problems have implemented I/M programs. Recently, with the passage of the U.S. Clean Air Act Amendments of 1990, many states have been required to significantly upgrade the performance and coverage of their I/M programs. I/M programs also have been implemented in Europe and recently in Asia. This presentation reviews developments in I/M programs for light-duty gasoline powered vehicles. Developments in I/M programs for diesel powered vehicles are briefly described. (author)

Fuel Rod Melt Progression Simulation Using Low-Temperature Melting Metal Alloy

International Nuclear Information System (INIS)

Seung Dong Lee; Suh, Kune Y.; GoonCherl Park; Un Chul Lee

2002-01-01

The TMI-2 accident and various severe fuel damage experiments have shown that core damage is likely to proceed through various states before the core slumps into the lower head. Numerous experiments were conducted to address when and how the core can lose its original geometry, what geometries are formed, and in what processes the core materials are transported to the lower plenum of the reactor pressure vessel. Core degradation progresses along the line of clad ballooning, clad oxidation, material interaction, metallic blockage, molten pool formation, melt progression, and relocation to the lower head. Relocation into the lower plenum may occur from the lateral periphery or from the bottom of the core depending upon the thermal and physical states of the pool. Determining the quantities and rate of molten material transfer to the lower head is important since significant amounts of molten material relocated to the lower head can threaten the vessel integrity by steam explosion and thermal and mechanical attack of the melt. In this paper the focus is placed on the melt flow regime on a cylindrical fuel rod utilizing the LAMDA (Lumped Analysis of Melting in Degrading Assemblies) facility at the Seoul National University. The downward relocation of the molten material is a combination of the external film flow and the internal pipe flow. The heater rods are 0.8 m long and are coated by a low-temperature melting metal alloy. The electrical internal heating method is employed during the test. External heating is adopted to simulate the exothermic Zircaloy-steam reaction. Tests are conducted in several quasi-steady-state conditions. Given the variable boundary conditions including the heat flux and the water level, observation is made for the melting location, progression, and the mass of molten material. Finally, the core melt progression model is developed from the visual inspection and quantitative analysis of the experimental data. As the core material relocates

Respuestas faciales ante imágenes de advertencia de tabaco

Directory of Open Access Journals (Sweden)

M. A. Muñoz

Full Text Available Resumen En 2003, la Comisión Europea propuso una serie de advertencias visuales para ser incluidas en los embalajes de tabaco, con el objetivo de motivar a los fumadores a dejar de fumar y promover actitudes negativas hacia el tabaco. El objetivo de este estudio fue evaluar el impacto de las advertencias sanitarias mediante autoinformes y medidas psicofisiológicas. Cincuenta sujetos sanos (19-23 años visionaron un conjunto de treinta y seis imágenes de diferente contenido emocional y veinticuatro del banco de imágenes preventivas propuestas por la Comisión Europea. Se registró la actividad eléctrica de los músculos cigomático mayor y corrugador mientras los sujetos visionaban estas imágenes. A continuación, los participantes evaluaban las imágenes en las dimensiones de agradabilidad y activación. Los resultados muestran una mayor actividad eléctrica del musculo corrugador ante la presentación de imágenes desagradables comparadas con advertencias desagradables incluidas en los paquetes de tabaco. Estos resultados sugieren que la campaña preventiva podría beneficiarse de imágenes preventivas más impactantes, promoviendo así la activación del sistema motivacional evitativo/defensivo.

Ductile failure in upsetting of a rapid-solidification-processed aluminium alloy

NARCIS (Netherlands)

Habraken, F.A.C.M.; Dautzenberg, J.H.

1993-01-01

Cold upset-tests have been performed on a Rapid Solidification Processed (RSP) aluminium-alloy, produced by the ‘melt-spun ribbons’-process out of 70% car-scrap and 30% primary scrap. The ribbons are hot extruded, resulting in 29 mm diameter bar. Its properties regarding plastic flow and fracture

Effect of wheel speed on magnetic and mechanical properties of melt spun Fe-6.5 wt.% Si high silicon steel

Science.gov (United States)

Ouyang, Gaoyuan; Jensen, Brandt; Tang, Wei; Dennis, Kevin; Macziewski, Chad; Thimmaiah, Srinivasa; Liang, Yongfeng; Cui, Jun

2018-05-01

Fe-Si electric steel is the most widely used soft magnetic material in electric machines and transformers. Increasing the silicon content from 3.2 wt.% to 6.5 wt.% brings about large improvement in the magnetic and electrical properties. However, 6.5 wt.% silicon steel is inherited with brittleness owing to the formation of B2 and D03 ordered phase. To obtain ductility in Fe-6.5wt.% silicon steel, the ordered phase has to be bypassed with methods like rapid cooling. In present paper, the effect of cooling rate on magnetic and mechanical properties of Fe-6.5wt.% silicon steel is studied by tuning the wheel speed during melt spinning process. The cooling rate significantly alters the ordering and microstructure, and thus the mechanical and magnetic properties. X-ray diffraction data shows that D03 ordering was fully suppressed at high wheel speeds but starts to nucleate at 10m/s and below, which correlates with the increase of Young's modulus towards low wheel speeds as tested by nanoindentation. The grain sizes of the ribbons on the wheel side decrease with increasing wheel speeds, ranging from ˜100 μm at 1m/s to ˜8 μm at 30m/s, which lead to changes in coercivity.

Exchange bias behavior in Ni{sub 50.0}Mn{sub 35.5} In{sub 14.5} ribbons annealed at different temperatures

Energy Technology Data Exchange (ETDEWEB)

Sanchez, T. [Dept. de Fisica, Universidad de Oviedo, Calvo Sotelo s/n, 33007 Oviedo (Spain); Sato Turtelli, R.; Groessinger, R. [Institut fur Festkoerperphysik, Technische Universitaet Wien, Wiedner Hauptstr. 8-10, 1040 Vienna (Austria); Sanchez, M.L.; Santos, J.D.; Rosa, W.O.; Prida, V.M. [Dept. de Fisica, Universidad de Oviedo, Calvo Sotelo s/n, 33007 Oviedo (Spain); Escoda, Ll.; Sunol, J.J. [Campus de Montilivi, Universidad de Girona, edifici PII, Lluis Santalo s/n. 17003 Girona (Spain); Koledov, V. [Kotelnikov Institute of Radio Engineering and Electronics, RAS, Moscow 125009 (Russian Federation); Hernando, B., E-mail: grande@uniovi.es [Dept. de Fisica, Universidad de Oviedo, Calvo Sotelo s/n, 33007 Oviedo (Spain)

2012-10-15

Heusler alloy Ni{sub 50.0}Mn{sub 35.5}In{sub 14.5} ribbons were prepared by melt-spinning technique. Several short time annealings were carried out in order to enhance the exchange bias effect in this alloy ribbon. The magnetic transition temperature increases with the annealing, compared to the as-spun sample, however no significant differences in respective Curie temperatures were observed for austenite and martensite phases in such annealed samples. Exchange bias effect is observed at low temperatures for all samples and practically vanishes at 60 K for the as-spun sample, whereas for the annealed ribbons it vanishes at 100 K.

Jung und Alt im Dialog

Directory of Open Access Journals (Sweden)

Caroline Baetge

2012-04-01

Full Text Available Rezension zu: Kupser, Thomas, und Ida Pöttinger, Hrsg. 2011. Mediale Brücken: Generationen im Dialog durch aktive Medienarbeit. Gesellschaft - Altern - Medien 3. München: kopaed.

Developing an effective IM/IT strategy.

Science.gov (United States)

Kramer, Sarah; Walker, Joanne; Falk, Will

2009-01-01

Healthcare organizations and systems around the world lag far behind banking, manufacturing, travel and other industries in their use of information management/information technology (IM/IT) to deliver high-quality products and services. Across Canada, healthcare organizations, as well as governments, understand that information and information technology are needed to deliver quality care and to sustain our publicly funded health system. However, insufficient funding, few experienced resources, lack of strong leadership and absence of clear business/clinical rationale have restricted innovation and advancement in the use of IM/IT to improve healthcare delivery and patient outcomes.

Shock melting method to determine melting curve by molecular dynamics: Cu, Pd, and Al.

Science.gov (United States)

Liu, Zhong-Li; Zhang, Xiu-Lu; Cai, Ling-Cang

2015-09-21

A melting simulation method, the shock melting (SM) method, is proposed and proved to be able to determine the melting curves of materials accurately and efficiently. The SM method, which is based on the multi-scale shock technique, determines melting curves by preheating and/or prepressurizing materials before shock. This strategy was extensively verified using both classical and ab initio molecular dynamics (MD). First, the SM method yielded the same satisfactory melting curve of Cu with only 360 atoms using classical MD, compared to the results from the Z-method and the two-phase coexistence method. Then, it also produced a satisfactory melting curve of Pd with only 756 atoms. Finally, the SM method combined with ab initio MD cheaply achieved a good melting curve of Al with only 180 atoms, which agrees well with the experimental data and the calculated results from other methods. It turned out that the SM method is an alternative efficient method for calculating the melting curves of materials.

Shock melting method to determine melting curve by molecular dynamics: Cu, Pd, and Al

International Nuclear Information System (INIS)

Liu, Zhong-Li; Zhang, Xiu-Lu; Cai, Ling-Cang

2015-01-01

A melting simulation method, the shock melting (SM) method, is proposed and proved to be able to determine the melting curves of materials accurately and efficiently. The SM method, which is based on the multi-scale shock technique, determines melting curves by preheating and/or prepressurizing materials before shock. This strategy was extensively verified using both classical and ab initio molecular dynamics (MD). First, the SM method yielded the same satisfactory melting curve of Cu with only 360 atoms using classical MD, compared to the results from the Z-method and the two-phase coexistence method. Then, it also produced a satisfactory melting curve of Pd with only 756 atoms. Finally, the SM method combined with ab initio MD cheaply achieved a good melting curve of Al with only 180 atoms, which agrees well with the experimental data and the calculated results from other methods. It turned out that the SM method is an alternative efficient method for calculating the melting curves of materials

Real-time resource availability signalling in IMS-based networks

NARCIS (Netherlands)

Ozcelebi, T.; Radovanovic, I.; Lukkien, J.J.

2007-01-01

The emerging converged IP multimedia subsystem (IMS) allows the use of unlicensed, nondedicated and nondeterministic computer access networks for delivering IP multimedia services. To provide end-to-end quality-of-service (QoS) over such networks combined with the IMS core network, for resource

Medida Interpessoal de Psicopatia (IM-P: estudo preliminar no contexto brasileiro Interpersonal Measure of Psychopathy (IM-P: preliminary study in the Brazilian context

Directory of Open Access Journals (Sweden)

Tárcia Rita Davoglio

2011-01-01

Full Text Available INTRODUÇÃO: A observação direta do comportamento interpessoal é um recurso importante na descrição e diagnóstico da personalidade psicopática. A Medida Interpessoal de Psicopatia (Interpersonal Measure of Psychopathy, IM-P é um instrumento psicométrico composto por 21 itens, desenvolvido para ser utilizado em associação com outras escalas de avaliação da psicopatia. Foca-se, especificamente, nos comportamentos interpessoais e aspectos não verbais evidentes na interação do entrevistador com indivíduos que apresentam características psicopáticas. OBJETIVO: Descrever resultados preliminares sobre a investigação de aspectos interpessoais da psicopatia mediante a utilização da IM-P, incluindo as etapas de tradução/adaptação e avaliação de confiabilidade interavaliadores da IM-P, em uma amostra de adolescentes brasileiros. MÉTODO: Trata-se de estudo transversal, descritivo e correlacional realizado com 20 adolescentes masculinos cumprindo medida socioeducativa com privação de liberdade na Região Metropolitana de Porto Alegre (RS. Após os procedimentos de tradução da escala, treinamento dos pesquisadores e teste piloto por meio de uma entrevista semiestruturada, a IM-P foi pontuada por três juízes independentes. RESULTADOS: Os resultados estatísticos, obtidos através do coeficiente de concordância de Kendall, revelaram grau de concordância interavaliadores elevado e satisfatório para os escores totais da IM-P (W = 0,84; p INTRODUCTION: The direct observation of interpersonal behaviors is an important resource in the description and diagnosis of the psychopathic personality. The Interpersonal Measure of Psychopathy (IM-P is a psychometric instrument comprised of 21 items, designed to be applied in association with other instruments that also evaluate psychopaths. It focuses specifically on interpersonal and non-verbal behaviors that become evident during the interaction between the interviewer and individuals

The Microwave Properties of Simulated Melting Precipitation Particles: Sensitivity to Initial Melting

Science.gov (United States)

Johnson, B. T.; Olson, W. S.; Skofronick-Jackson, G.

2016-01-01

A simplified approach is presented for assessing the microwave response to the initial melting of realistically shaped ice particles. This paper is divided into two parts: (1) a description of the Single Particle Melting Model (SPMM), a heuristic melting simulation for ice-phase precipitation particles of any shape or size (SPMM is applied to two simulated aggregate snow particles, simulating melting up to 0.15 melt fraction by mass), and (2) the computation of the single-particle microwave scattering and extinction properties of these hydrometeors, using the discrete dipole approximation (via DDSCAT), at the following selected frequencies: 13.4, 35.6, and 94.0GHz for radar applications and 89, 165.0, and 183.31GHz for radiometer applications. These selected frequencies are consistent with current microwave remote-sensing platforms, such as CloudSat and the Global Precipitation Measurement (GPM) mission. Comparisons with calculations using variable-density spheres indicate significant deviations in scattering and extinction properties throughout the initial range of melting (liquid volume fractions less than 0.15). Integration of the single-particle properties over an exponential particle size distribution provides additional insight into idealized radar reflectivity and passive microwave brightness temperature sensitivity to variations in size/mass, shape, melt fraction, and particle orientation.

Modelling and Predicting the Breaking Strength and Mass Irregularity of Cotton Rotor-Spun Yarns Containing Cotton Fiber Recovered from Ginning Process by Using Artificial Neural Network Algorithm

Directory of Open Access Journals (Sweden)

Mohsen Shanbeh

2011-01-01

Full Text Available One of the main methods to reduce the production costs is waste recycling which is the most important challenge for the future. Cotton wastes collected from ginning process have desirable properties which could be used during spinning process. The purpose of this study was to develop predictive models of breaking strength and mass irregularity (CV% of cotton waste rotor-spun yarns containing cotton waste collected from ginning process by using the artificial neural network trained with backpropagation algorithm. Artificial neural network models have been developed based on rotor diameter, rotor speed, navel type, opener roller speed, ginning waste proportion and yarn linear density as input parameters. The parameters of artificial neural network model, namely, learning, and momentum rate, number of hidden layers and number of hidden processing elements (neurons were optimized to get the best predictive models. The findings showed that the breaking strength and mass irregularity of rotor spun yarns could be predicted satisfactorily by artificial neural network. The maximum error in predicting the breaking strength and mass irregularity of testing data was 8.34% and 6.65%, respectively.

Address Translation Problems in IMS Based Next Generation Networks

Directory of Open Access Journals (Sweden)

Balazs Godor

2006-01-01

Full Text Available The development of packed based multimedia networks reached a turning point when the ITU-T and the ETSIhave incorporated the IMS to the NGN. With the fast development of mobile communication more and more services andcontent are available. In contrast with fix network telephony both the services and the devices are personalized in the “mobileworld”. Services, known from the Internet - like e-mail, chat, browsing, presence, etc. – are already available via mobiledevices as well. The IMS originally wanted to exploit both the benefits of mobile networks and the fancy services of theInternet. But today it is already more than that. IMS is the core of the next generation telecommunication networks and abasis for fix-mobile convergent services. The fact however that IMS was originally a “mobile” standard, where IPv6 was notoddity generated some problems for the fix networks, where IPv4 is used. In this article I give an overview of these problemsand mention some solutions as well.

DEPENDENCY OF SULFATE SOLUBILITY ON MELT COMPOSITION AND MELT POLYMERIZATION

International Nuclear Information System (INIS)

JANTZEN, CAROL M.

2004-01-01

Sulfate and sulfate salts are not very soluble in borosilicate waste glass. When sulfate is present in excess it can form water soluble secondary phases and/or a molten salt layer (gall) on the melt pool surface which is purported to cause steam explosions in slurry fed melters. Therefore, sulfate can impact glass durability while formation of a molten salt layer on the melt pool can impact processing. Sulfate solubility has been shown to be compositionally dependent in various studies, (e.g. , B2O3, Li2O, CaO, MgO, Na2O, and Fe2O3 were shown to increase sulfate solubility while Al2O3 and SiO2 decreased sulfate solubility). This compositional dependency is shown to be related to the calculated melt viscosity at various temperatures and hence the melt polymerization

Gesundheit und Pflege im Alter

OpenAIRE

Pfaff, Martin

1989-01-01

Gesundheit und Pflege im Alter : d. Gesundheitsreformgesetz (GRG) ; Möglichkeiten, Grenzen u. weitere Vorschläge / Martin Pfaff ; Klaus Deimer. - In: Expertengespräch "Pflege in der Familie". - Augsburg, 1989. - Getr. Zählung

Digitalisierung im Verteilnetz: Evolution oder Revolution anhand konkreter Beispiele

Science.gov (United States)

Krone, Oliver; Bachmann, Maurus

Durch die Integration der neuen erneuerbaren Energien steht das Stromnetz vor großen Herausforderungen. Das Energiesystem als Gesamtes und die Verteilnetze im Speziellen werden smart. Anhand konkreter Beispiele wird aufgezeigt, wie die Digitalisierung im Elektrizitätsnetz voranschreitet. Diese Entwicklung ist eine Evolution, nicht aber eine Revolution.

THOR Ion Mass Spectrometer instrument - IMS

Science.gov (United States)

Retinò, Alessandro; Kucharek, Harald; Saito, Yoshifumi; Fraenz, Markus; Verdeil, Christophe; Leblanc, Frederic; Techer, Jean-Denis; Jeandet, Alexis; Macri, John; Gaidos, John; Granoff, Mark; Yokota, Shoichiro; Fontaine, Dominique; Berthomier, Matthieu; Delcourt, Dominique; Kistler, Lynn; Galvin, Antoniette; Kasahara, Satoshi; Kronberg, Elena

2016-04-01

Turbulence Heating ObserveR (THOR) is the first mission ever flown in space dedicated to plasma turbulence. Specifically, THOR will study how turbulent fluctuations at kinetic scales heat and accelerate particles in different turbulent environments within the near-Earth space. To achieve this goal, THOR payload is being designed to measure electromagnetic fields and particle distribution functions with unprecedented resolution and accuracy. Here we present the Ion Mass Spectrometer (IMS) instrument that will measure the full three-dimensional distribution functions of near-Earth main ion species (H+, He+, He++ and O+) at high time resolution (~ 150 ms for H+ , ~ 300 ms for He++) with energy resolution down to ~ 10% in the range 10 eV/q to 30 keV/q and angular resolution ~ 10°. Such high time resolution is achieved by mounting multiple sensors around the spacecraft body, in similar fashion to the MMS/FPI instrument. Each sensor combines a top-hat electrostatic analyzer with deflectors at the entrance together with a time-of-flight section to perform mass selection. IMS electronics includes a fast sweeping high voltage board that is required to make measurements at high cadence. Ion detection includes Micro Channel Plates (MCP) combined with Application-Specific Integrated Circuits (ASICs) for charge amplification, discrimination and time-to-digital conversion (TDC). IMS is being designed to address many of THOR science requirements, in particular ion heating and acceleration by turbulent fluctuations in foreshock, shock and magnetosheath regions. The IMS instrument is being designed and will be built by an international consortium of scientific institutes with main hardware contributions from France, USA, Japan and Germany.

Aggregation und Management von Metadaten im Kontext von Europeana

Directory of Open Access Journals (Sweden)

Gerda Koch

2017-09-01

Full Text Available Mit dem In-Beziehung-Setzen und Verlinken von Daten im Internet wird der Weg zur Umsetzung des semantischen Webs geebnet. Erst die semantische Verbindung von heterogenen Datenbeständen ermöglicht übergreifende Suchvorgänge und späteres „Machine Learning“. Im Artikel werden die Aktivitäten der Europäischen Digitalen Bibliothek im Bereich des Metadatenmanagements und der semantischen Verlinkung von Daten skizziert. Dabei wird einerseits ein kurzer Überblick zu aktuellen Forschungsschwerpunkten und Umsetzungsstrategien gegeben, und darüber hinaus werden einzelne Projekte und maßgeschneiderte Serviceangebote für naturhistorische Daten, regionale Kultureinrichtungen und Audiosammlungen beschrieben.

The Processing Design of Jute Spun Yarn/PLA Braided Composite by Pultrusion Molding

Directory of Open Access Journals (Sweden)

Anin Memon

2013-01-01

Full Text Available Prevalently, the light has been shed on the green composite from the viewpoint of environmental protection. Jute fibers are natural fibers superior due to light weight, low cost, and being environmentally friendly corresponding to the green composite materials. Meticulously, fibers of polylactic acid (PLA thermoplastic biopolymer were used as the resin fibers. In this study, the fabrication of tubular jute spun yarn/PLA braided composite by pultrusion molding was presented. The intermediate materials were prepared by commingled technique. The braiding technique manufactured preform which had jute fiber diagonally oriented at certain angles with the glass fiber inserted into the braiding yarns along the longitudinal direction. The braided preforms were pulled through a heated die where the consolidation flow took place due to reduced matrix viscosity and pressure. The pultrusion experiments were done with jute/PLA commingled yarns and combined with glass fiber yarns to fabricate the tubular composite. Impregnation quality was evaluated by microscope observation of the pultruded cross-sections. The flexural mechanical properties of the pultruded were measured by four-point bending test.

Melting of contaminated metallic waste

International Nuclear Information System (INIS)

Lee, Y.-S.; Cheng, S.-Y.; Kung, H.-T.; Lin, L.-F.

2004-01-01

Approximately 100 tons of contaminated metallic wastes were produced each year due to maintenance for each TPC's nuclear power reactor and it was roughly estimated that there will be 10,000 tons of metallic scraps resulted from decommissioning of each reactor in the future. One means of handling the contaminated metal is to melt it. Melting process owns not only volume reduction which saves the high cost of final disposal but also resource conservation and recycling benefits. Melting contaminated copper and aluminum scraps in the laboratory scale have been conducted at INER. A total of 546 kg copper condenser tubes with a specific activity of about 2.7 Bq/g was melted in a vacuum induction melting facility. Three types of products, ingot, slag and dust were derived from the melting process, with average activities of 0.10 Bq/g, 2.33 Bq/g and 84.3 Bq/g respectively. After the laboratory melting stage, a pilot plant with a 500 kg induction furnace is being designed to melt the increasingly produced contaminated metallic scraps from nuclear facilities and to investigate the behavior of different radionuclides during melting. (author)

Dynamics of Melting and Melt Migration as Inferred from Incompatible Trace Element Abundance in Abyssal Peridotites

Science.gov (United States)

Peng, Q.; Liang, Y.

2008-12-01

To better understand the melting processes beneath the mid-ocean ridge, we developed a simple model for trace element fractionation during concurrent melting and melt migration in an upwelling steady-state mantle column. Based on petrologic considerations, we divided the upwelling mantle into two regions: a double- lithology upper region where high permeability dunite channels are embedded in a lherzolite/harzburgite matrix, and a single-lithology lower region that consists of partially molten lherzolite. Melt generated in the single lithology region migrates upward through grain-scale diffuse porous flow, whereas melt in the lherzolite/harzburgite matrix in the double-lithology region is allowed to flow both vertically through the overlying matrix and horizontally into its neighboring dunite channels. There are three key dynamic parameters in our model: degree of melting experienced by the single lithology column (Fd), degree of melting experienced by the double lithology column (F), and a dimensionless melt suction rate (R) that measures the accumulated rate of melt extraction from the matrix to the channel relative to the accumulated rate of matrix melting. In terms of trace element fractionation, upwelling and melting in the single lithology column is equivalent to non-modal batch melting (R = 0), whereas melting and melt migration in the double lithology region is equivalent to a nonlinear combination of non-modal batch and fractional melting (0 abyssal peridotite, we showed, with the help of Monte Carlo simulations, that it is difficult to invert for all three dynamic parameters from a set of incompatible trace element data with confidence. However, given Fd, it is quite possible to constrain F and R from incompatible trace element abundances in residual peridotite. As an illustrative example, we used the simple melting model developed in this study and selected REE and Y abundance in diopside from abyssal peridotites to infer their melting and melt migration

Sexting im Schulumfeld

Directory of Open Access Journals (Sweden)

Barbara Buchegger

2015-03-01

Full Text Available Wir wollten es einfach wissen. Wie steht es nun mit diesem "Sexting" – also der Übermittlung von Nacktaufnahmen, die Jugendliche untereinander teilen? Stimmt unser Eindruck aus den Workshops in Schulen, dass es bereits ein "übliches Verhalten" der Jugendlichen geworden ist? Saferinternet.at hat im November/Dezember 2014 eine Studie durch das Institut für Jugendkulturforschung rund um das Thema "Sexting" in Auftrag gegeben.

A two-stage extraction procedure for insensitive munition (IM) explosive compounds in soils.

Science.gov (United States)

Felt, Deborah; Gurtowski, Luke; Nestler, Catherine C; Johnson, Jared; Larson, Steven

2016-12-01

The Department of Defense (DoD) is developing a new category of insensitive munitions (IMs) that are more resistant to detonation or promulgation from external stimuli than traditional munition formulations. The new explosive constituent compounds are 2,4-dinitroanisole (DNAN), nitroguanidine (NQ), and nitrotriazolone (NTO). The production and use of IM formulations may result in interaction of IM component compounds with soil. The chemical properties of these IM compounds present unique challenges for extraction from environmental matrices such as soil. A two-stage extraction procedure was developed and tested using several soil types amended with known concentrations of IM compounds. This procedure incorporates both an acidified phase and an organic phase to account for the chemical properties of the IM compounds. The method detection limits (MDLs) for all IM compounds in all soil types were regulatory risk-based Regional Screening Level (RSL) criteria for soil proposed by the U.S. Army Public Health Center. At defined environmentally relevant concentrations, the average recovery of each IM compound in each soil type was consistent and greater than 85%. The two-stage extraction method decreased the influence of soil composition on IM compound recovery. UV analysis of NTO established an isosbestic point based on varied pH at a detection wavelength of 341 nm. The two-stage soil extraction method is equally effective for traditional munition compounds, a potentially important point when examining soils exposed to both traditional and insensitive munitions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Medienpädagogische Aufgabenfelder hinsichtlich der Visualität im digitalen Zeitalter. Desiderate im Umgang mit visuellen Medienkulturen

Directory of Open Access Journals (Sweden)

Petra Missomelius

2017-04-01

Full Text Available Die bildungskulturell leitende Funktion des Buches diffundiert im digitalen Zeitalter mobiler und transversaler Systeme von Netzwerkmedien. Zudem sind soziokulturelle Lebenswelten wie Bildungsinstitutionen, Familie und Peers durch Heterogenität gekennzeichnet. Indem auch diese Teil des Geflechts medienkultureller Architekturen werden, geraten ehemals gültige Unterscheidungsparameter wie explizites und implizites, formelles und informelles Wissen ins Wanken. Grenzziehungen und konkurrierende Auffassungen gegenüber diesen, vormals als der Bildung entgegengesetzt wahrgenommenen, Bereichen erweisen sich nunmehr als problematisch. So spielt Visualität im Kontext multimodal zusammengesetzter Bildungsmaterialien eine zunehmende Rolle und wird als Möglichkeit des Umgangs mit Komplexität eingesetzt. Wenngleich somit die Zurückhaltung gegenüber (Bewegt-Bildmedien in der pädagogischen Praxis schwindet, so haben sich mit der Digitalisierung medienkulturell bedeutsame Felder eröffnet, welche erziehungswissenschaftlicher Beachtung bedürfen. Eine sich der Komplexität digitaler Medienkulturen stellende Medienpädagogik bringt mit sich, dass auch Funktion und Gebrauch visueller Medien im Kontext von Bildungsprozessen reflektiert stattfinden. Medienpädagogisch informiertes Agieren in visuellen Medienkulturen ist darüber hinaus heute gerade deshalb essentiell, da es sich bei digital generierter Visualität um eine neue Qualität im Unterschied zu traditionellen Bildmedien handelt, welche der Logik der Repräsentation entsprachen. Der Beitrag thematisiert Desiderate, die sich hinsichtlich des Visuellen datenbasierter Medien für die Medienpädagogik ergeben, und geht dabei auf kommunikative Bildlichkeit, auf paradigmatische mediale Formen und auf datengestützte Wissensgenerierung ein.

IMS Intra- and Inter Domain End-to-End Resilience Analysis

DEFF Research Database (Denmark)

Kamyod, Chayapol; Nielsen, Rasmus Hjorth; Prasad, Neeli R.

2013-01-01

This paper evaluated resilience of the reference IMS based network topology in operation through the keys reliability parameters via OPNET. The reliability behaviors of communication within similar and across registered home IMS domains were simulated and compared. Besides, the reliability effects...

Infrared and swelling study of the hydration-induced phase transition of wet-spun hyaluronate films

Science.gov (United States)

Hoppe, A. D.; Marlowe, R. L.; Lee, S. A.; Powell, J. W.; Rupprecht, A.

1997-03-01

The hydration properties of wet-spun films of hyaluronate (HA) with four different counterions (Li^+, Cs^+, Mg^2+, and Ca^2+) have been studied using optical microscopy, optical birefringence and infrared (IR) spectroscopy. Small pieces of these films were found to be optically birefringent up to hydration levels near 90 % relative humidity (RH). All four kinds of films then became optically isotropic and display dramatic changes in size. These changes are consistent with the occurrence of an order-disorder (o-d) transition. IR spectroscopy of the backbone region (from 800 to 1000 cm-1) suggests that the Li^+, Cs^+ and Ca^2+ films are very similar. Two IR bands in this region are observed at low RH and show no dependence on hydration until the o-d transition. The IR spectra of CaHA show five bands in this region. These five bands are observed to 95 % RH.

EFEKTIVITAS MEDIA PEMBELAJARAN IM3 DITINJAU DARI MOTIVASI BELAJAR

Directory of Open Access Journals (Sweden)

J. Handhika

2012-10-01

Full Text Available Penelitian ini bertujuan untuk mengetahui perbedaan penggunaan media pembelajaran IM3 berbasis flash dan media MS. Power Point terhadap prestasi belajar IPA-Fisika. Hasil penelitian  menunjukkan bahwa siswa yang diajar menggunakan media IM3 berbasis flash memberikan rata-rata prestasi lebih baik dibandingkan dengan siswa yang diajar menggunakan power point. Siswa dengan motivasi belajar tinggi menghasilkan rata-rata prestasi lebih baik daripada siswa dengan motivasi belajar rendah, serta terdapat interaksi motivasi belajar dengan media pembelajaran terhadap prestasi belajar IPA-Fisika.   This study aims to determine differences in the use of flash-based IM3 learning media and MS media. Power Point to IPA-Physics learning achievement. Results showed that students who were taught using flash-based media IM3 gives an average performance better than students who were taught using the power point. Students with high motivation to learn the average yield better performance than students with low learning motivation, and there is interaction with the medium of learning motivation toward science learning achievement-Physics.

Ausländische Direktinvestitionen und Technologietransfer im angolanischen Energiesektor

Directory of Open Access Journals (Sweden)

2016-04-01

Full Text Available Dem Zusammenhang von ausländischen Direktinvestionen (Foreign Direct Investment, FDI und Technologietransfer wird sowohl in der Forschung als auch in der politischen Analyse große Bedeutung zugeschrieben. Zahlreiche Veröffentlichungen belegen, dass FDI den Transfer von und/oder den Zugang zu Technologien erleichtert. Allerdings gibt es zu wenige empirische Studien, die diesen Zusammenhang in Bezug auf die Wirtschaft afrikanischer Staaten untersuchen. Der Autor will diese Lücke zu einem kleinen Teil schließen, indem er die Bedeutung des Technologietransfers durch den Zufluss von FDI im Energiesektor Angolas ermittelt. Seine Analyse basiert auf qualitativer Forschung in Angola im Jahr 2014. Er zeigt auf, dass sich die Erzeugung von Energie(trägern und die Verteilungsinfrastruktur - maschinelle Ausrüstung und Qualifizierung - durch den Zufluss von FDI erheblich entwickeln konnte. Allerdings gebe es keinen Beleg dafür, dass dieser Zufluss die endogenen wissenschaftlichen und technologischen Forschungspotenziale im angolanischen Energiesektor gefördert hat. Der Autor empfiehlt politische Maßnahmen zur Förderung dieser Fähigkeiten, insbesondere im Bereich der Produktion.

Modelling of the controlled melt flow in a glass melting space – Its melting performance and heat losses

Czech Academy of Sciences Publication Activity Database

Jebavá, Marcela; Dyrčíková, Petra; Němec, Lubomír

2015-01-01

Roč. 430, DEC 15 (2015), s. 52-63 ISSN 0022-3093 Institutional support: RVO:67985891 Keywords : glass melt flow * mathematical modelling * energy distribution * space utilizatios * melting performance Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 1.825, year: 2015

Recent Changes in Arctic Sea Ice Melt Onset, Freeze-Up, and Melt Season Length

Science.gov (United States)

Markus, Thorsten; Stroeve, Julienne C.; Miller, Jeffrey

2010-01-01

In order to explore changes and trends in the timing of Arctic sea ice melt onset and freeze-up and therefore melt season length, we developed a method that obtains this information directly from satellite passive microwave data, creating a consistent data set from 1979 through present. We furthermore distinguish between early melt (the first day of the year when melt is detected) and the first day of continuous melt. A similar distinction is made for the freeze-up. Using this method we analyze trends in melt onset and freeze-up for 10 different Arctic regions. In all regions except for the Sea of Okhotsk, which shows a very slight and statistically insignificant positive trend (O.4 days/decade), trends in melt onset are negative, i.e. towards earlier melt. The trends range from -1.0day/decade for the Bering Sea to -7.3 days/decade for the East Greenland Sea. Except for the Sea of Okhotsk all areas also show a trend towards later autumn freeze onset. The Chukchi/Beaufort Seas and Laptev/East Siberian Seas observe the strongest trends with 7 days/decade. For the entire Arctic, the melt season length has increased by about 20 days over the last 30 years. Largest trends of over 1O days/decade are seen for Hudson Bay, the East Greenland Sea the Laptev/East Siberian Seas, and the Chukchi/Beaufort Seas. Those trends are statistically significant a1 the 99% level.

Reaction of soda-lime-silica glass melt with water vapour at melting temperatures

Czech Academy of Sciences Publication Activity Database

Vernerová, Miroslava; Kloužek, Jaroslav; Němec, Lubomír

2015-01-01

Roč. 416, MAY 15 (2015), s. 21-30 ISSN 0022-3093 R&D Projects: GA TA ČR TA01010844 Institutional support: RVO:67985891 Keywords : glass melt * sulfate * water vapour * bubble nucleation * melt foaming * glass melting Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 1.825, year: 2015

ifo Konjunkturprognose 2015/2016: Deutsche Wirtschaft im Aufschwung

OpenAIRE

Wollmershäuser, Timo; Nierhaus, Wolfgang; Berg, Tim Oliver; Breuer, Christian; Garnitz, Johanna; Grimme, Christian; Henzel, Steffen; Hristov, Atanas; Hristov, Nikolay; Meister, Wolfgang; Schröter, Felix; Steiner, Andreas; Wieland, Elisabeth; Wohlrabe, Klaus; Wolf, Anna

2015-01-01

Die deutsche Wirtschaft befindet sich derzeit in einem kräftigen Aufschwung. Das reale Bruttoinlandsprodukt wird in diesem Jahr voraussichtlich um 1,9% expandieren und im kommenden Jahr um 1,8%. Der private Konsum bleibt die Stütze des Aufschwungs, da die Einkommensperspektiven der privaten Haushalte aufgrund der sich weiter verbessernden Arbeitsmarktlage gut sind. Allerdings entfallen allmählich die Kaufkraftgewinne durch den Ölpreisrückgang, so dass sich die Konsumdynamik im Prognosezeitrau...

Transition metal ions in silicate melts. I. Manganese in sodium silicate melts

Energy Technology Data Exchange (ETDEWEB)

Nelson, C; White, W B

1980-01-01

Optical absorption spectra obtained on glasses quenched from sodium silicate melts show Mn/sup 3 +/ to be the dominant species for melts heated in air and Mn/sup 2 +/ to be the dominant species for melts heated at P/sub O/sub 2// = 10/sup -17/ bar. The absorption spectrum of Mn/sup 3 +/ consists of an intense band at 20,000 cm/sup -1/ with a 15,000 cm/sup -1/ satellite possibly arising from the Jahn-Teller effect. The independence of the spectrum from melt composition and the high band intensity is offered as evidence for a distinct Mn/sup 3 +/ complex in the melt. The spectrum of Mn/sup 2 +/ is weak and many expected bands are not observed. A two-band luminescence spectrum from Mn/sup 2 +/ has been tentatively interpreted as due to Mn/sup 2 +/ in interstitial sites in the network and Mn/sup 2 +/ coordiated by non-bridging oxygens.

On high-pressure melting of tantalum

Science.gov (United States)

Luo, Sheng-Nian; Swift, Damian C.

2007-01-01

The issues related to high-pressure melting of Ta are discussed within the context of diamond-anvil cell (DAC) and shock wave experiments, theoretical calculations and common melting models. The discrepancies between the extrapolations of the DAC melting curve and the melting point inferred from shock wave experiments, cannot be reconciled either by superheating or solid-solid phase transition. The failure to reproduce low-pressure DAC melting curve by melting models such as dislocation-mediated melting and the Lindemann law, and molecular dynamics and quantum mechanics-based calculations, undermines their predictions at moderate and high pressures. Despite claims to the contrary, the melting curve of Ta (as well as Mo and W) remains inconclusive at high pressures.

Semi-metallic, strong and stretchable wet-spun conjugated polymer microfibers

KAUST Repository

Zhou, Jian

2015-01-21

A dramatic improvement in electrical conductivity is necessary to make conductive polymer fibers viable candidates in applications such as flexible electrodes, conductive textiles, and fast-response sensors and actuators. In this study, high-performance poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT/PSS) conjugated polymer microfibers were fabricated via wet-spinning followed by hot-drawing. Due to the combined effects of the vertical hot-drawing process and doping/de-doping the microfibers with ethylene glycol (EG), we achieved a record electrical conductivity of 2804 S cm−1. This is, to the best of our knowledge, a six-fold improvement over the best previously reported value for PEDOT/PSS fibers (467 S cm−1) and a two-fold improvement over the best values for conductive polymer films treated by EG de-doping (1418 S cm−1). Moreover, we found that these highly conductive fibers experience a semiconductor–metal transition at 313 K. They also have superior mechanical properties with a Young\\'s modulus up to 8.3 GPa, a tensile strength reaching 409.8 MPa and a large elongation before failure (21%). The most conductive fiber also demonstrates an extraordinary electrical performance during stretching/unstretching: the conductivity increased by 25% before the fiber rupture point with a maximum strain up to 21%. Simple fabrication of the semi-metallic, strong and stretchable wet-spun PEDOT/PSS microfibers described here could make them available for conductive smart electronics.

Measuring cognitive change with ImPACT: the aggregate baseline approach.

Science.gov (United States)

Bruce, Jared M; Echemendia, Ruben J; Meeuwisse, Willem; Hutchison, Michael G; Aubry, Mark; Comper, Paul

2017-11-01

The Immediate Post-Concussion Assessment and Cognitive Test (ImPACT) is commonly used to assess baseline and post-injury cognition among athletes in North America. Despite this, several studies have questioned the reliability of ImPACT when given at intervals employed in clinical practice. Poor test-retest reliability reduces test sensitivity to cognitive decline, increasing the likelihood that concussed athletes will be returned to play prematurely. We recently showed that the reliability of ImPACT can be increased when using a new composite structure and the aggregate of two baselines to predict subsequent performance. The purpose of the present study was to confirm our previous findings and determine whether the addition of a third baseline would further increase the test-retest reliability of ImPACT. Data from 97 English speaking professional hockey players who had received at least 4 ImPACT baseline evaluations were extracted from a National Hockey League Concussion Program database. Linear regression was used to determine whether each of the first three testing sessions accounted for unique variance in the fourth testing session. Results confirmed that the aggregate baseline approach improves the psychometric properties of ImPACT, with most indices demonstrating adequate or better test-retest reliability for clinical use. The aggregate baseline approach provides a modest clinical benefit when recent baselines are available - and a more substantial benefit when compared to approaches that obtain baseline measures only once during the course of a multi-year playing career. Pending confirmation in diverse samples, neuropsychologists are encouraged to use the aggregate baseline approach to best quantify cognitive change following sports concussion.

ImSET: Impact of Sector Energy Technologies

Energy Technology Data Exchange (ETDEWEB)

Roop, Joseph M.; Scott, Michael J.; Schultz, Robert W.

2005-07-19

This version of the Impact of Sector Energy Technologies (ImSET) model represents the ''next generation'' of the previously developed Visual Basic model (ImBUILD 2.0) that was developed in 2003 to estimate the macroeconomic impacts of energy-efficient technology in buildings. More specifically, a special-purpose version of the 1997 benchmark national Input-Output (I-O) model was designed specifically to estimate the national employment and income effects of the deployment of Office of Energy Efficiency and Renewable Energy (EERE) -developed energy-saving technologies. In comparison with the previous versions of the model, this version allows for more complete and automated analysis of the essential features of energy efficiency investments in buildings, industry, transportation, and the electric power sectors. This version also incorporates improvements in the treatment of operations and maintenance costs, and improves the treatment of financing of investment options. ImSET is also easier to use than extant macroeconomic simulation models and incorporates information developed by each of the EERE offices as part of the requirements of the Government Performance and Results Act.

Solvation of UCl{sub 6}{sup 2-} anionic complex by MeBu{sub 3}N{sup +}, BuMe{sub 2}Im{sup +} and BuMeIm{sup +} cations

Energy Technology Data Exchange (ETDEWEB)

Bosse, Emilie; Den Auwer, Christophe; Berthon, Claude; Guilbaud, Philippe; Moisy, Philippe [CEA Marcoule, DRCP/SCPS, BP 17171, 30207 Bagnols sur Ceze Cedex (France); Grigoriev, Mikhail S. [A.N. Frumkin Institute of Physical Chemistry and Electrochemistry, RAS, Leninskii Prosp. 31, 119991 Moscow (Russian Federation); Nikitenko, Serguei [CNAB, UMR 5084, CNRS - Universite de Bordeaux 1, BP 120 Le Haut Vigneau, 33175 Gradignan Cedex (France); Le Naour, Claire; Cannes, Celine [IPN, UMR 8608, CNRS, Universite Paris-Sud, 91406 Orsay (France)

2008-07-01

The complexes [MeBu{sub 3}N]{sub 2}[UCl{sub 6}] and [BuMe{sub 2}Im]{sub 2}[UCl{sub 6}] were characterized in the solid state and in solution of [MeBu{sub 3}N][Tf{sub 2}N], [BuMe{sub 2}Im][Tf{sub 2}N] and [BuMeIm][Tf{sub 2}N] room temperature ionic liquids using single-crystal XRD, EXAFS, electrochemistry, UV-visible absorption spectroscopy and NMR. In the solid and in solution, the existence of hydrogen bonding between the anionic UCl{sub 6}{sup 2-} complex and the ionic liquid cations were revealed by these techniques. The MeBu{sub 3}N{sup +} cation interacts with UCl{sub 6}{sup 2-} via the protons on the alpha carbon atoms of nitrogen. The protons of the imidazolium ring account for the interaction between the BuMe{sub 2}Im+ cation and the UCl{sub 6}{sup 2-} anion. For the BuMeIm{sup +} cation the major interaction was confirmed between the most acidic proton on C(2) and UCl{sub 6}{sup 2-}. The experimental results also show that the intensity of the interaction between the UCl{sub 6}{sup 2-} anion and the cation varies with the ionic liquid cation in the following order: MeBu{sub 3}N{sup +} {approx} BuMe{sub 2}Im{sup +} << BuMeIm{sup +}. (authors)

Handover Based IMS Registration Scheme for Next Generation Mobile Networks

Directory of Open Access Journals (Sweden)

Shireen Tahira

2017-01-01

Full Text Available Next generation mobile networks aim to provide faster speed and more capacity along with energy efficiency to support video streaming and massive data sharing in social and communication networks. In these networks, user equipment has to register with IP Multimedia Subsystem (IMS which promises quality of service to the mobile users that frequently move across different access networks. After each handover caused due to mobility, IMS provides IPSec Security Association establishment and authentication phases. The main issue is that unnecessary reregistration after every handover results in latency and communication overhead. To tackle these issues, this paper presents a lightweight Fast IMS Mobility (FIM registration scheme that avoids unnecessary conventional registration phases such as security associations, authentication, and authorization. FIM maintains a flag to avoid deregistration and sends a subsequent message to provide necessary parameters to IMS servers after mobility. It also handles the change of IP address for user equipment and transferring the security associations from old to new servers. We have validated the performance of FIM by developing a testbed consisting of IMS servers and user equipment. The experimental results demonstrate the performance supremacy of FIM. It reduces media disruption time, number of messages, and packet loss up to 67%, 100%, and 61%, respectively, as compared to preliminaries.

Regelungen im Verkehr mit Lebensmitteln und Bedarfsgegenständen in Deutschland

Science.gov (United States)

Thomas, Gundula; Freund, Astrid; Gründig, Friedrich

Im Zuge der Globalisierung von Produktion und Handel ändert sich auch der Charakter der Vorschriften im Lebensmittelrecht. Zunehmend treten internationale Rechtsbestimmungen, Abkommen, Standards und andere Normen an die Stelle nationaler Regelungen.

Robust stator resistance identification of an IM drive using model reference adaptive system

International Nuclear Information System (INIS)

Madadi Kojabadi, Hossein; Abarzadeh, Mostafa; Aghaei Farouji, Said

2013-01-01

Highlights: ► We estimate the stator resistance and rotor speed of the IM. ► We proposed a new quantity to estimate the speed and stator resistance of IM. ► The proposed algorithm is robust to rotor resistance variations. ► We estimate the IM speed and stator resistance simultaneously to avoid speed error. - Abstract: Model reference adaptive system (MRAS) based robust stator resistance estimator for sensorless induction motor (IM) drive is proposed. The MRAS is formed with a semi-active power quantity. The proposed identification method can be achieved with on-line tuning of the stator resistance with robustness against rotor resistance variations. Stable and efficient estimation of IM speed at low region will be guaranteed by simultaneous identification of IM speed and stator resistance. The stability of proposed stator resistance estimator is checked through Popov’s hyperstability theorem. Simulation and experimental results are given to highlight the feasibility, the simplicity, and the robustness of the proposed method.

Thermal Degradation Study of IM7/DMBZ-15 High Temperature Composite by TGA/FTIR

National Research Council Canada - National Science Library

Nadler, Melvin

2003-01-01

(U) High temperature graphite composites such as IM7/8552 epoxy, IM7/5250 BMI, and IM7/DMBZ-15 polyimide show blistering and/or "catastrophic" delamination when rapidly heated to temperatures above...

Melt inclusions: Chapter 6

Science.gov (United States)

,; Lowenstern, J. B.

2014-01-01

Melt inclusions are small droplets of silicate melt that are trapped in minerals during their growth in a magma. Once formed, they commonly retain much of their initial composition (with some exceptions) unless they are re-opened at some later stage. Melt inclusions thus offer several key advantages over whole rock samples: (i) they record pristine concentrations of volatiles and metals that are usually lost during magma solidification and degassing, (ii) they are snapshots in time whereas whole rocks are the time-integrated end products, thus allowing a more detailed, time-resolved view into magmatic processes (iii) they are largely unaffected by subsolidus alteration. Due to these characteristics, melt inclusions are an ideal tool to study the evolution of mineralized magma systems. This chapter first discusses general aspects of melt inclusions formation and methods for their investigation, before reviewing studies performed on mineralized magma systems.

[Variation im heutigen Deutsch...] / Laura Tidrike

Index Scriptorium Estoniae

Tidrike, Laura

2008-01-01

Arvustus: Variation im heutigen Deutsch : Perspektiven für den Sprachunterricht / hrsg. v. Eva Neuland. Frankfurt am Main : Lang, 2006. (Sprache - Kommunikation - Kultur. Soziolinguistische Beiträge ; Vol. 4)

Global R&D through the Intelligent Manufacturing Systems (IMS) program

Science.gov (United States)

Huray, Paul G.

1997-01-01

The industry-led, international intelligent manufacturing systems (IMS) program provides a special vehicle for joint research and development between government, industry and academia in the United States, Canada, Japan, Australia, and Europe. Since its beginning in 1989, the IMS program has progressed through a feasibility phase which demonstrated that international legal barriers, trade issues, and intellectual property problems could be overcome. The program is constructed to provide higher quality design, customized products, shorter delivery cycles and lower costs. Interactions between partner companies have led to new business opportunities for mutual profit and some claim to have learned strategic information about their international competitors. The IMS program is growing through the participation of hundreds of corporate and university partners who share responsibilities in specific projects and jointly reap benefits for their manufacturing products and processes. The logic for choosing or not choosing the IMS mechanisms will be discussed and R and D projects will be identified.

The improved magnetic properties in phosphorus substituted Pr-Fe-P-B nanocomposites

International Nuclear Information System (INIS)

Jin, Z.Q.; Zhang, Y.; Wang, H.L.; Klaessig, A.; Bonder, M.; Hadjipanayis, G.C.

2003-01-01

Phosphorus substituted (Pr,Tb) 8 (Fe,Nb,Zr,P) 88 B 4 nanocomposites have been produced by melt-spinning. The effects of phosphorus substitution as well as wheel speed on the crystallization behavior and magnetic properties of the melt-spun samples have been investigated. With the substitution of phosphorus, the crystallization temperature of amorphous phase increases. The optimum wheel speed was found to be around 25 m/s for as-spun ribbons and 40 m/s for the annealed samples, both of which present excellent second quadrant hysteresis loop shapes due to the fine grain size of α-Fe which is around 20 nm. The addition of phosphorus also greatly improves the coercivity of Pr-Fe-B nanocomposites without a significant loss of saturation magnetization. A higher coercivity of 9.2 kOe in P-substituted samples was obtained as compared to 8.1 kOe in P-free samples. This is attributed to a narrower temperature span between the crystallization into TbCu 7 structure and the transformation into the 2:14:1 phase caused by the phosphorus substitution

Estudios por imágenes en reumatismo

Directory of Open Access Journals (Sweden)

Muñoz Ch. Sara, Dra.

2012-07-01

Los grandes avances tecnológicos de la última década han mejorado la calidad y cantidad de información que las distintas técnicas aportan, especialmente la RM; esto hace vislumbrar un cambio significativo en el diagnóstico por imágenes, ya que en el futuro no solo estará basado en los cambios morfológicos en órganos y tejidos; las imágenes obtenidas aportarán información bioquímica, molecular y fisiológica de los procesos patológicos facilitando su diagnóstico aun más precoz.

High-pressure melting curve of KCl: Evidence against lattice-instability theories of melting

International Nuclear Information System (INIS)

Ross, M.; Wolf, G.

1986-01-01

We show that the large curvature in the T-P melting curve of KCl is the result of a reordering of the liquid to a more densely packed arrangement. As a result theories of melting, such as the instability model, which do not take into account the structure of the liquid fail to predict the correct pressure dependence of the melting curve

Using IMS VDEX in Agrega

Directory of Open Access Journals (Sweden)

Jose Manuel Canabal

2009-03-01

Full Text Available An essential element in a learning object repository is the meta-information associated with the resources housed by the repository, as this is what enables the objects to be retrieved. In many cases, the meta-information which is described consists of the classification of a resource in relation to a taxonomy or thesaurus. Agrega is a network of learning object repositories in which an LOM profile, called LOM-ES, has been used to label the objects. Part of the meta-information described corresponds to the classification of the object with respect to a group of taxonomies and a thesaurus, which have had to be described using the ims vdex standard to enable them to be managed from the federation nodes. This article describes the way in which ims vdex has been used in order to create this description and how these metadata instances are managed.

Synthesis of a single phase of high-entropy Laves intermetallics in the Ti-Zr-V-Cr-Ni equiatomic alloy

Science.gov (United States)

Yadav, T. P.; Mukhopadhyay, Semanti; Mishra, S. S.; Mukhopadhyay, N. K.; Srivastava, O. N.

2017-12-01

The high-entropy Ti-Zr-V-Cr-Ni (20 at% each) alloy consisting of all five hydride-forming elements was successfully synthesised by the conventional melting and casting as well as by the melt-spinning technique. The as-cast alloy consists entirely of the micron size hexagonal Laves Phase of C14 type; whereas, the melt-spun ribbon exhibits the evolution of nanocrystalline Laves phase. There was no evidence of any amorphous or any other metastable phases in the present processing condition. This is the first report of synthesising a single phase of high-entropy complex intermetallic compound in the equiatomic quinary alloy system. The detailed characterisation by X-ray diffraction, scanning and transmission electron microscopy and energy-dispersive X-ray spectroscopy confirmed the existence of a single-phase multi-component hexagonal C14-type Laves phase in all the as-cast, melt-spun and annealed alloys. The lattice parameter a = 5.08 Å and c = 8.41 Å was determined from the annealed material (annealing at 1173 K). The thermodynamic calculations following the Miedema's approach support the stability of the high-entropy multi-component Laves phase compared to that of the solid solution or glassy phases. The high hardness value (8.92 GPa at 25 g load) has been observed in nanocrystalline high-entropy alloy ribbon without any cracking. It implies that high-yield strength ( 3.00 GPa) and the reasonable fracture toughness can be achieved in this high-entropy material.

Electron beam melting of sponge titanium

International Nuclear Information System (INIS)

Kanayama, Hiroshi; Kusamichi, Tatsuhiko; Muraoka, Tetsuhiro; Onouye, Toshio; Nishimura, Takashi

1991-01-01

Fundamental investigations were done on electron beam (EB) melting of sponge titanium by using 80 kW EB melting furnace. Results obtained are as follows: (1) To increase the melting yield of titanium in EB melting of sponge titanium, it is important to recover splashed metal by installation of water-cooled copper wall around the hearth and to decrease evaporation loss of titanium by keeping the surface temperature of molten metal just above the melting temperature of titanium without local heating. (2) Specific power consumption of drip melting of pressed sponge titanium bar and hearth melting of sponge titanium are approximately 0.9 kWh/kg-Ti and 0.5-0.7 kWh/kg-Ti, respectively. (3) Ratios of the heat conducted to water-cooled mould in the drip melting and to water-cooled hearth in the hearth melting to the electron beam input power are 50-65% and 60-65%, respectively. (4) Surface defects of EB-melted ingots include rap which occurs when the EB output is excessively great, and transverse cracks when the EB output is excessively small. To prevent surface defects, the up-down withdrawal method is effective. (author)

İletişim Çalışmalarında Yeni Bir Mecra: Finansal İletişim

Directory of Open Access Journals (Sweden)

Gökhan Gökgöz

2013-09-01

Full Text Available 1970’li yıllar toplumsal ve politik tarih açısından önemli bir uğrağı temsil eder. Bu yılların başında yaşanan kriz, ekonominin işleyiş süreçlerini, devletin yapısını ve toplumsal alanın tasavvur edilme biçimini büyük ölçüde değiştirmiştir. Bu dönemde, finansal sermaye, kapitalizm içerisinde bir hegemonik lider olarak ön plana çıkmış; devlet, bir yandan üretimin çekirdeğinden uzak bir yerde konumlandırılırken diğer yandan paranın dolaşım kanallarının rehabilitasyonu işine odaklanmış; insana ilişkin değerler, kültürel mefhumlar ve toplumsal pratikler ise birer değişken olarak ekonomi-politikanın merkezine taşınmıştır. Kültür ile ekonomi arasındaki geleneksel ilişki bozulmuş; bir ekonomi-politikanın başarısı, toplumsal aktörlere temas etme kabiliyeti ile paralel hale gelmiştir. Finansallaşma sürecinde bu temas, iletişim politikaları vasıtasıyla sağlanır; ekonomi-politika ve bundan sorumlu merkezi kurumlarla toplumsal alan arasındaki bağ, iletişim stratejileri üzerinden kurulur; ekonomik alan ile kültürel alan arasındaki boşluk, iletişim kanalları içerisinden taşınan enformasyon marifetiyle doldurulur; insana ilişkin öngörülemezlikler, iletişim süreçleri vasıtasıyla öngörülebilir kılınır. Bu çalışmada, iletişim çalışmaları içerisinde yeni bir mecra olarak çağrılan “finansal iletişim”in farklı temas noktalarına işaret edilecek ve her bir uğrağın finansal iletişim alanına bağlandığı nokta, modeller üzerinden gösterilecektir. 

Ein Ausblick auf Supply-Chain-Management im Jahr 2016

DEFF Research Database (Denmark)

Wieland, Andreas

2016-01-01

Wie sieht Supply-Chain-Management im Jahr 2016 aus? Was erwartet uns? Vieles deutet darauf hin, dass SCM in Zukunft sogar noch mehr auf den Kunden gerichtet sein könnte als bisher.......Wie sieht Supply-Chain-Management im Jahr 2016 aus? Was erwartet uns? Vieles deutet darauf hin, dass SCM in Zukunft sogar noch mehr auf den Kunden gerichtet sein könnte als bisher....

Melting point of yttria

International Nuclear Information System (INIS)

Skaggs, S.R.

1977-06-01

Fourteen samples of 99.999 percent Y 2 O 3 were melted near the focus of a 250-W CO 2 laser. The average value of the observed melting point along the solid-liquid interface was 2462 +- 19 0 C. Several of these same samples were then melted in ultrahigh-purity oxygen, nitrogen, helium, or argon and in water vapor. No change in the observed temperature was detected, with the exception of a 20 0 C increase in temperature from air to helium gas. Post test examination of the sample characteristics, clarity, sphericity, and density is presented, along with composition. It is suggested that yttria is superior to alumina as a secondary melting-point standard

Report on converging insert moulding with µ-IM

DEFF Research Database (Denmark)

Islam, Aminul

moulding with µ-IM  Task 5.2.1 and COTECH demonstrator: guide line for 5PRC production based on the concept of Task 5.2.1 Information and results provided by this deliverable will be directly used for one of the COTECH demonstrators production which will call for convergent insert moulding with µ......Task 5.2.1 deals with the technical feasibility of converging the state-of-the-art µ IM process with insert moulding to offer a wide range of multi-material µ components. The main objective of this deliverable is to summarize state-of-the-art information and to make the guideline needed...... for the convergence. In particular the following aspects are summed up in the deliverable:  Need for converging insert moulding with µ-IM  Objectives and expected outcome from task 5.2.1  State-of-the-art micro insert moulding and different scenario of micro insert moulding  Challenges ahead of converging insert...

A SURVEY ON INDIAN EXPERIENCE ON INTEGRATED MANAGEMENT STANDARDS (IMS

Directory of Open Access Journals (Sweden)

H. Khanna

2009-09-01

Full Text Available Adoption of management systems standards is a key issue in manufacturing industry in India. Following the global trend quality and environmental issues are gaining importance. However the number of ISO 14001 certified companies are much less in India as compared to ISO 9001. The integration of ISO 14001 with ISO 9001 may help companies to sustain competitive advantage and overcome disappointments with quality standards and in turn encourage companies to adopt good environmental practices. The aim of this research is to study the implementation of integrated management standards (IMS by the manufacturing organizations in India. The different aspects of integration and benefits of IMS implementation are analyzed. This r esearch is based on empirical study carried out in Indian manufacturing firms, involving the application of a questionnaire. This questionnaire was tested on 50 manufacturing companies in India. The study reveals that focus on stakeholders; top management commitment and training are critical success factors for implementation of IMS. The main benefits of integration are discussed. The small sample size is one of the major limitations of this study. The paper informs the managers in manufacturing organizations and practitioners of management system standards especially in developing countries about IMS and will enable them to adopt IMS in future so that those organizations may not implement multiple and overlapping MSS(Management System Standards.

Environmental trace analysis by means of supersensitive GC-IMS

International Nuclear Information System (INIS)

Leonhardt, J.W.

1997-01-01

The effective control of pollutants in ambient air requires their fast in situ identification and concentration determination of chemical compounds in the range of micrograms per m 3 . There are attempts to use conventional analytical techniques as portable GC and GC-MS. These systems are relatively expensive. A new supersensitive ion Mobility Sensor (IMS) was developed and checked by IUT Ltd, which meets the new demands. The use of tritium sources is an advantage in comparison with other IMS being equipped by nickel-63, the application of which is rather critical in respect of the radiation protection. On the other hand an integrated separation column allows to reduce interferences by matrix effects. The technical parameters of the IUT GC- IMS and some of its most important applications are briefly presented

Method of melting solid waste

International Nuclear Information System (INIS)

Ootsuka, Katsuyuki; Mizuno, Ryokichi; Kuwana, Katsumi; Sawada, Yoshihisa; Komatsu, Fumiaki.

1982-01-01

Purpose: To enable the volume reduction treatment of a HEPA filter containing various solid wastes, particularly acid digestion residue, or an asbestos separator at a relatively low temperature range. Method: Solid waste to be heated and molten is high melting point material treated by ''acid digestion treatment'' for treating solid waste, e.g. a HEPA filter or polyvinyl chloride, etc. of an atomic power facility treated with nitric acid or the like. When this material is heated and molten by an electric furnace, microwave melting furnace, etc., boron oxide, sodium boride, sodium carbonate, etc. is added as a melting point lowering agent. When it is molten in this state, its melting point is lowered, and it becomes remarkably fluid, and the melting treatment is facilitated. Solidified material thus obtained through the melting step has excellent denseness and further large volume reduction rate of the solidified material. (Yoshihara, H.)

On the interplay of morphology and electronic conductivity of rotationally spun carbon fiber mats

Science.gov (United States)

Opitz, Martin; Go, Dennis; Lott, Philipp; Müller, Sandra; Stollenwerk, Jochen; Kuehne, Alexander J. C.; Roling, Bernhard

2017-09-01

Carbon-based materials are used as electrode materials in a wide range of electrochemical applications, e.g., in batteries, supercapacitors, and fuel cells. For these applications, the electronic conductivity of the materials plays an important role. Currently, porous carbon materials with complex morphologies and hierarchical pore structures are in the focus of research. The complex morphologies influence the electronic transport and may lead to an anisotropic electronic conductivity. In this paper, we unravel the influence of the morphology of rotationally spun carbon fiber mats on their electronic conductivity. By combining experiments with finite-element simulations, we compare and evaluate different electrode setups for conductivity measurements. While the "bar-type method" with two parallel electrodes on the same face of the sample yields information about the intrinsic conductivity of the carbon fibers, the "parallel-plate method" with two electrodes on opposite faces gives information about the electronic transport orthogonal to the faces. Results obtained for the van-der-Pauw method suggest that this method is not well suited for understanding morphology-transport relations in these materials.

Fatigue behaviour of core-spun yarns containing filament by means of cyclic dynamic loading

Science.gov (United States)

Esin, S.; Osman, B.

2017-10-01

The behaviour of yarns under dynamic loading is important that leads to understand the growth characteristics which is exposed to repetitive loadings during usage of fabric made from these yarns. Fabric growth is undesirable property that originated from low resilience characteristics of fabric. In this study, the effects of the filament fineness and yarn linear density on fatigue behaviour of rigid-core spun yarns were determined. Cotton covered yarns containing different filament fineness of polyester (PET) draw textured yarns (DTY) (100d/36f, 100d/96f, 100d/144f, 100d/192f and 100d/333f) and yarn linear densities (37 tex, 30 tex, 25 tex and 21 tex) were manufactured by using a modified ring spinning system at the same spinning parameters. Repetitive loads were applied for 25 cycles at levels between 0.1 and 3 N. Dynamic modulus and dynamic strain of yarn samples were analyzed statistically. Results showed that filament fineness and yarn linear density have significance effect on dynamic modulus and dynamic strain after cyclic loading.

Thermodynamics of Oligonucleotide Duplex Melting

Science.gov (United States)

Schreiber-Gosche, Sherrie; Edwards, Robert A.

2009-01-01

Melting temperatures of oligonucleotides are useful for a number of molecular biology applications, such as the polymerase chain reaction (PCR). Although melting temperatures are often calculated with simplistic empirical equations, application of thermodynamics provides more accurate melting temperatures and an opportunity for students to apply…

Automatic Control of Silicon Melt Level

Science.gov (United States)

Duncan, C. S.; Stickel, W. B.

1982-01-01

A new circuit, when combined with melt-replenishment system and melt level sensor, offers continuous closed-loop automatic control of melt-level during web growth. Installed on silicon-web furnace, circuit controls melt-level to within 0.1 mm for as long as 8 hours. Circuit affords greater area growth rate and higher web quality, automatic melt-level control also allows semiautomatic growth of web over long periods which can greatly reduce costs.

Digital Medien im Naturwissenschaftlichen Unterricht

CERN Document Server

Meßinger-Koppelt, Jenny

2014-01-01

„Morgens, 8 Uhr: Kurz vor der Schultür werden noch die neuesten Posts auf Facebook geliked, ein Selfie in die Whats-App-Gruppe hochgeladen oder auf YouTube noch ein #LOL-Video gestreamed. Dann klingelt es und die Digital Natives greifen wieder zu Stift, Papier und werden frontal mit Fakten gefüttert“ (A. Spang). Für Schüler sind Internet, Smartphone und Tablet-PC heute selbstverständlicher Teil ihrer Lernwelt. Und auch die Alltags- und Berufswelt ist ohne Informationstechnologien nicht mehr vorstellbar. Doch was bedeutet das für den Schulunterricht, insbesondere für die techniknahen Naturwissenschaften? Wie gelingt im Schulalltag die Balance zwischen Kreidezeit und interaktivem Whiteboard nach mittlerweile 30 Jahren Erfahrung mit Schulcomputern? Der vorliegende Sammelband präsentiert zahlreiche Praxisbeispiele aus dem Schulalltag zum sinnvollen Einsatz digitaler Medien im Biologie-, Chemie- und Physik-Unterricht sowie den aktuellen Stand der fachdidaktischen Forschung. Zu Wort kommen Hochschullehr...

CORPORATIVE MOTIVES ON IMPLEMENTATION OF INTEGRATED MANAGEMENT SYSTEM (IMS

Directory of Open Access Journals (Sweden)

Dragan Rajkovic

2009-09-01

Full Text Available Integration of management systems for quality, environment, health and risk management as well as corporative social responsibilities is workable corporative approach to reduce costs, effective use of resources, higher motivation of employees and better fulfillment of requirements of social engagements and stakeholders. This paper presents contents of literature and review of a company motives on integrated management system (IMS implementation, namely factors affecting the IMS implementation.

Melting of polydisperse hard disks

NARCIS (Netherlands)

Pronk, S.; Frenkel, D.

2004-01-01

The melting of a polydisperse hard-disk system is investigated by Monte Carlo simulations in the semigrand canonical ensemble. This is done in the context of possible continuous melting by a dislocation-unbinding mechanism, as an extension of the two-dimensional hard-disk melting problem. We find

Tracking the Depleted Mantle Signature in Melt Inclusions and Residual Glass of Basaltic Martian Shergottites using Secondary Ionization Mass Spectrometry

Science.gov (United States)

Peters, Timothy J.; Simon, Justin I.; Jones, John H.; Usui, Tomohiro; Economos, Rita C.; Schmitt, Axel K.; McKeegan, Kevin D.

2013-01-01

Trace element abundances of depleted shergottite magmas recorded by olivine-hosted melt inclusions (MI) and interstitial mesostasis glass were measured using the Cameca ims-1270 ion microprobe. Two meteorites: Tissint, an olivine-­phyric basaltic shergottite which fell over Morocco July 18th 2001; and the Antarctic meteorite Yamato 980459 (Y98), an olivine-phyric basaltic shergottite with abundant glassy mesostasis have been studied. Chondrite-­normalized REE patterns for MI in Tissint and Y98 are characteristically LREE depleted and, within analytical uncertainty, parallel those of their respective whole rock composition; supporting each meteorite to represent a melt composition that has experienced closed-­system crystallization. REE profiles for mesostasis glass in Y98 lie about an order of magnitude higher than those from the MI; with REE profiles for Tissint MI falling in between. Y98 MI have the highest average Sm/Nd and Y/Ce ratios, reflecting their LREE depletion and further supporting Y98 as one of our best samples to probe the depleted shergotitte mantle. In general, Zr/Nb ratios overlap between Y98 and Tissint MI, Ce/Nb ratios overlap between Y98 MI and mesostasis glass, and Sm/Nd ratios overlap between Y98 mesostasis glass and Tissint MI. These features support similar sources for both, but with subtle geochemical differences that may reflect different melting conditions or fractionation paths during ascent from the mantle. Interestingly, the REE patterns for both Y98 bulk and MI analyses display a flattening of the LREE that suggests a crustal contribution to the Y98 parent melt. This observation has important implications for the origins of depleted and enriched shergottites.

Melt cooling by bottom flooding: The experiment CometPC-H3. Ex-vessel core melt stabilization research

International Nuclear Information System (INIS)

Alsmeyer, H.; Cron, T.; Merkel, G.; Schmidt-Stiefel, S.; Tromm, W.; Wenz, T.

2003-03-01

The CometPC-H3 experiment was performed to investigate melt cooling by water addition to the bottom of the melt. The experiment was performed with a melt mass of 800 kg, 50% metal and 50% oxide, and 300 kW typical decay heat were simulated in the melt. As this was the first experiment after repair of the induction coil, attention was given to avoid overload of the induction coil and to keep the inductor voltage below critical values. Therefore, the height of the sacrificial concrete layer was reduced to 5 cm only, and the height of the porous concrete layers was also minimized to have a small distance and good coupling between heated melt and induction coil. After quite homogeneous erosion of the upper sacrificial concrete layer, passive bottom flooding started from the porous concrete after 220 s with 1.3 liter water/s. The melt was safely stopped, arrested and cooled. The porous, water filled concrete was only slightly attacked by the hot melt in the upper 25 mm of one sector of the coolant device. The peak cooling rate in the early contact phase of coolant water and melt was 4 MW/m 2 , and exceeded the decay heat by one order of magnitude. The cooling rate remarkably dropped, when the melt was covered by the penetrating water and a surface crust was formed. Volcanic eruptions from the melt during the solidification process were observed from 360 - 510 s and created a volcanic dome some 25 cm high, but had only minor effect on the generation of a porous structure, as the expelled melt solidified mostly with low porosity. Unfortunately, decay heat simulation in the melt was interrupted at 720 s by an incorrect safety signal, which excluded further investigation of the long term cooling processes. At that time, the melt was massively flooded by a layer of water, about 80 cm thick, and coolant water inflow was still 1 l/s. The melt had reached a stable situation: Downward erosion was stopped by the cooling process from the water filled, porous concrete layer. Top

Detection of microbial volatile organic compounds (MVOC) by means of ion mobility spectroscopy (IMS); Detektion leicht fluechtiger organischer Verbindungen mikrobiellen Ursprungs (MVOC) mittels Ionenmobilitaetsspektrometrie (IMS)

Energy Technology Data Exchange (ETDEWEB)

Tiebe, Carlo

2010-07-01

Traces of microbial volatile organic compounds (MVOCs) can indicate the growth of moulds in the indoor air. The application of ion mobility spectrometry (IMS) is a very promising method for the detection of these MVOCs due to its high sensitivity. A mobile IMS device was tested to use this analytical-chemical method for in situ indoor air diagnostics. The first part of this work describes the test gas generation of 14 MVOCs in the laboratory. The test gases were produced by preparation of permeation procedures. Due to the MVOCs test gases IMS parameters like reduced mobility (K{sub 0}), relative drift time (t{sub rd}), the concentration dependency of MVOCs signals were determined and the limit of detection (LOD) was calculated. The LODs are in the range of 2 to 192 {mu}g m{sup -3} (1 to 51 ppb{sub V}). In the second part of this manuscript seven different mould species were cultivated on nutrient media and their MVOCs emissions were explored. It was found out, that the MVOCs emissions of moulds have a dependency of species and of their cultivation time. These results are confirmed by principal component analysis (PCA). The identification of these MVOCs was performed by test-related GC-MS analysis and approved these results. The MVOCs emissions were explored in the cultivation of mould mixtures on three different building materials. The IMS-results were interpreted chemo metrically by PCA. It was possible to find different emission patterns of cultivated moulds on building materials without an identification of the MVOCs inside the emission chamber. In 27 field trials of different indoor environments (rooms) the IMS was tested to detect MVOCs. In 59 % of the cases a positive correlation is determined between visible mould-infested rooms and the detected MVOCs by IMS. (orig.)

Environmental trace analysis by means of supersensitive GC-IMS

Energy Technology Data Exchange (ETDEWEB)

Leonhardt, J.W. [IUTLimited, Berlin, (Germany)

1997-10-01

The effective control of pollutants in ambient air requires their fast in situ identification and concentration determination of chemical compounds in the range of micrograms per m{sup 3}. There are attempts to use conventional analytical techniques as portable GC and GC-MS. These systems are relatively expensive. A new supersensitive ion Mobility Sensor (IMS) was developed and checked by IUT Ltd, which meets the new demands. The use of tritium sources is an advantage in comparison with other IMS being equipped by nickel-63, the application of which is rather critical in respect of the radiation protection. On the other hand an integrated separation column allows to reduce interferences by matrix effects. The technical parameters of the IUT GC- IMS and some of its most important applications are briefly presented 6 refs., 1 tab., 5 figs.

[Photoionization ion mobility spectrometry (UV-IMS) for the isomeric volatile organic compounds].

Science.gov (United States)

Li, Hu; Niu, Wen-qi; Wang, Hong-mei; Huang, Chao-qun; Jiang, Hai-he; Chu, Yan-nan

2012-01-01

The construction and performance study is reported for a newly developed ultraviolet photoionization ion mobility spectrometry (UV-IMS). In the present paper, an UV-IMS technique was firstly developed to detect eleven isomeric volatile organic compounds including the differences in the structure of carbon chain, the style of function group and the position of function group. Their reduced mobility values were determined and increased in this order: linears alcohols homemade UV-IMS was around ppb-ppm.

[Einheit und Vielfalt in der Rechtsgeschichte im Ostseeraum] / Marelle Leppik

Index Scriptorium Estoniae

Leppik, Marelle

2013-01-01

Arvustus: Einheit und Vielfalt in der Rechtsgeschichte im Ostseeraum. Unity and plurality in the legal history of the Baltic Sea area Sechster Rechtshistorikertag im Ostseeraum, 3.-5. Juni 2010 Tartu (Estland) / Riga (Lettland9. Hrsg. von Marju Luts-Sootak, Sanita Osipova und Frank L. Schäfer. (Rechtshistorische Reihe, Bd. 428.) Land. Frankfurt am Main u. a. 2012

Frauen im Netz weltweit – ausgegrenzt und mittendrin

Directory of Open Access Journals (Sweden)

Sigrid Peuker

2003-03-01

Full Text Available Mit dem Global Center for Women’s Studies and Politics (GLOW ist das Feministische Institut der Heinrich-Böll-Stiftung 1998 online gegangen. Mit diesem Schritt wurden Fragen nach den Möglichkeiten und Grenzen sowie nach den Gestaltungsräumen virtueller Kommunikation für Frauen zentral. Mit feminist_spaces. Frauen im Netz. Diskurse – Communities – Visionen, legt die Heinrich-Böll-Stiftung zusammen mit dem Feministischen Institut Antworten aus internationaler Perspektive vor. Das Buch geht auf die gleichnamige zweitätige Konferenz in Berlin im November 2001 zurück.

Model of interfacial melting

DEFF Research Database (Denmark)

Mouritsen, Ole G.; Zuckermann, Martin J.

1987-01-01

A two-dimensional model is proposed to describe systems with phase transitions which take place in terms of crystalline as well as internal degrees of freedom. Computer simulation of the model shows that the interplay between the two sets of degrees of freedom permits observation of grain-boundar......-boundary formation and interfacial melting, a nonequilibrium process by which the system melts at the boundaries of a polycrystalline domain structure. Lipid membranes are candidates for systems with pronounced interfacial melting behavior....

Melt migration modeling in partially molten upper mantle

Science.gov (United States)

Ghods, Abdolreza

The objective of this thesis is to investigate the importance of melt migration in shaping major characteristics of geological features associated with the partial melting of the upper mantle, such as sea-floor spreading, continental flood basalts and rifting. The partial melting produces permeable partially molten rocks and a buoyant low viscosity melt. Melt migrates through the partially molten rocks, and transfers mass and heat. Due to its much faster velocity and appreciable buoyancy, melt migration has the potential to modify dynamics of the upwelling partially molten plumes. I develop a 2-D, two-phase flow model and apply it to investigate effects of melt migration on the dynamics and melt generation of upwelling mantle plumes and focusing of melt migration beneath mid-ocean ridges. Melt migration changes distribution of the melt-retention buoyancy force and therefore affects the dynamics of the upwelling plume. This is investigated by modeling a plume with a constant initial melt of 10% where no further melting is considered. Melt migration polarizes melt-retention buoyancy force into high and low melt fraction regions at the top and bottom portions of the plume and therefore results in formation of a more slender and faster upwelling plume. Allowing the plume to melt as it ascends through the upper mantle also produces a slender and faster plume. It is shown that melt produced by decompressional melting of the plume migrates to the upper horizons of the plume, increases the upwelling velocity and thus, the volume of melt generated by the plume. Melt migration produces a plume which lacks the mushroom shape observed for the plume models without melt migration. Melt migration forms a high melt fraction layer beneath the sloping base of the impermeable oceanic lithosphere. Using realistic conditions of melting, freezing and melt extraction, I examine whether the high melt fraction layer is able to focus melt from a wide partial melting zone to a narrow region

Ultra-soft magnetic Co-Fe-B-Si-Nb amorphous alloys for high frequency power applications

Science.gov (United States)

Ackland, Karl; Masood, Ansar; Kulkarni, Santosh; Stamenov, Plamen

2018-05-01

With the continuous shrinkage of the footprint of inductors and transformers in modern power supplies, higher flux, while still low-loss metallic replacements of traditional ferrite materials are becoming an intriguing alternative. One candidate replacement strategy is based on amorphous CoFeBSi soft-magnetic alloys, in their metallic glass form. Here the structural and magnetic properties of two different families of CoFeBSi-based soft magnetic alloys, prepared by arc-melting and subsequent melt spinning (rapid quenching) are presented, targeting potential applications at effective frequencies of 100 kHz and beyond. The nominal alloy compositions are Co67Fe4B11Si16Mo2 representing commercial Vitrovac and Co72-xFexB28-y (where B includes non-magnetic elements such as Boron, Silicon etc. x varies between 4 and 5 % and y is varied from 0 to 2 %) denoted Alloy #1 and prepared as a possible higher performance alternative, i.e. lower power loss and lower coercivity, to commercial Vitrovac. Room temperature magnetization measurements of the arc-melted alloys reveal that compared to Vitrovac, Alloy #1 already presents a ten-fold decrease in coercivity, with Hc ˜ 1.4 Am-1 and highest figure of merit of (Ms/Hc > 96). Upon melt-spinning the alloys into thin (< 30 μm) ribbons, the alloys are essentially amorphous when analyzed by XRD. Magnetization measurements of the melt-spun ribbons demonstrate that Alloy #1 possesses a coercivity of just 2 Am-1, which represents a significant improvement compared to melt-spun ribbons of Vitrovac (17 Am-1). A set of prototype transformers of approximately 10 turns of Alloy #1 ribbon exhibits systematically Hc < 10 Am-1 at 100 kHz, without a noticeable decrease in coupled flux and saturation.

Can Nano-Particle Melt below the Melting Temperature of Its Free Surface Partner?

International Nuclear Information System (INIS)

Sui Xiao-Hong; Qin Shao-Jing; Wang Zong-Guo; Kang Kai; Wang Chui-Lin

2015-01-01

The phonon thermal contribution to the melting temperature of nano-particles is inspected. The discrete summation of phonon states and its corresponding integration form as an approximation for a nano-particle or for a bulk system have been analyzed. The discrete phonon energy levels of pure size effect and the wave-vector shifts of boundary conditions are investigated in detail. Unlike in macroscopic thermodynamics, the integration volume of zero-mode of phonon for a nano-particle is not zero, and it plays an important role in pure size effect and boundary condition effect. We find that a nano-particle will have a rising melting temperature due to purely finite size effect; a lower melting temperature bound exists for a nano-particle in various environments, and the melting temperature of a nano-particle with free boundary condition reaches this lower bound. We suggest an easy procedure to estimation the melting temperature, in which the zero-mode contribution will be excluded, and only several bulk quantities will be used as input. We would like to emphasize that the quantum effect of discrete energy levels in nano-particles, which is not present in early thermodynamic studies on finite size corrections to melting temperature in small systems, should be included in future researches. (condensed matter: structural, mechanical, and thermal properties)

Associations between United States Medical Licensing Examination (USMLE) and Internal Medicine In-Training Examination (IM-ITE) scores.

Science.gov (United States)

McDonald, Furman S; Zeger, Scott L; Kolars, Joseph C

2008-07-01

Little is known about the associations of previous standardized examination scores with scores on subsequent standardized examinations used to assess medical knowledge in internal medicine residencies. To examine associations of previous standardized test scores on subsequent standardized test scores. Retrospective cohort study. One hundred ninety-five internal medicine residents. Bivariate associations of United States Medical Licensing Examination (USMLE) Steps and Internal Medicine In-Training Examination (IM-ITE) scores were determined. Random effects analysis adjusting for repeated administrations of the IM-ITE and other variables known or hypothesized to affect IM-ITE score allowed for discrimination of associations of individual USMLE Step scores on IM-ITE scores. In bivariate associations, USMLE scores explained 17% to 27% of the variance in IME-ITE scores, and previous IM-ITE scores explained 66% of the variance in subsequent IM-ITE scores. Regression coefficients (95% CI) for adjusted associations of each USMLE Step with IM-ITE scores were USMLE-1 0.19 (0.12, 0.27), USMLE-2 0.23 (0.17, 0.30), and USMLE-3 0.19 (0.09, 0.29). No single USMLE Step is more strongly associated with IM-ITE scores than the others. Because previous IM-ITE scores are strongly associated with subsequent IM-ITE scores, appropriate modeling, such as random effects methods, should be used to account for previous IM-ITE administrations in studies for which IM-ITE score is an outcome.

Wir und die Anderen: Gruppenbezogene Menschenfeindlichkeit im Sport in Sachsen

OpenAIRE

Delto, Hannes; Tzschoppe, Petra

2015-01-01

Mit der Querschnittsstudie "Wir und die Anderen – Gruppenbezogene Menschenfeindlichkeit im organisierten Sport in Sachsen" wurde erstmals das Syndrom Gruppenbezogener Menschenfeindlichkeit im organisierten Sport untersucht. Das Konzept der Gruppenbezogenen Menschenfeindlichkeit – ausgehend von einer Ideologie der Ungleichwertigkeit – wurde von Prof. Wilhelm Heitmeyer (Universität Bielefeld) entwickelt. Die Ergebnisse ermöglichen explizite Aussagen über Ausmaß und Ursachen Gruppenbezogener Men...

Developments with melt spun RE-Fe-B powder for bonded magnets

International Nuclear Information System (INIS)

Brown, D.N.; Chen, Z.; Guschl, P.; Campbell, P.

2006-01-01

Rapidly quenched isotropic rare earth iron boride (RE-Fe-B) powders have found many applications throughout the electronics, automotive and white goods industries. The magnetic performance, thermal stability, corrosion resistance and processability of a powder are important factors when selecting a RE-Fe-B powder for a particular application. For electronic devices that operate at ambient temperatures, high remanence (B r ) tends to be a priority and RE 2 Fe 14 B/α-Fe nanocomposite powder magnets are favoured. Alternatively, automotive applications tend to require greater thermal stability and corrosion resistance, which are satisfied by single-phase RE 2 Fe 14 B powder magnets with higher intrinsic coercivity (H ci ). This article reviews the performance of commercially available rapidly solidified RE-Fe-B powders and recent developments made to address the demands of applications

Liquid coated melt-spun Nd-Fe-B powders for bonded magnets

Science.gov (United States)

Li, D.; Gaiffi, S.; Kirk, D.; Young, K.; Herchenroeder, J.; Berwald, T.

1999-04-01

The liquid coating (LC) has been employed to apply epoxy and lubricant over the surface of rapidly solidified Nd-Fe-B powder particles. The LC led to an improvement of physical and magnetic properties for the powders and magnets compared to the dry blending and the encapsulation methods. The LC powders have excellent flowability and can be used for bonded magnets requiring very close tolerances; further bonded magnets made using this powder posses higher strength.

Information management system study results. Volume 1: IMS study results

Science.gov (United States)

1971-01-01

The information management system (IMS) special emphasis task was performed as an adjunct to the modular space station study, with the objective of providing extended depth of analysis and design in selected key areas of the information management system. Specific objectives included: (1) in-depth studies of IMS requirements and design approaches; (2) design and fabricate breadboard hardware for demonstration and verification of design concepts; (3) provide a technological base to identify potential design problems and influence long range planning (4) develop hardware and techniques to permit long duration, low cost, manned space operations; (5) support SR&T areas where techniques or equipment are considered inadequate; and (6) permit an overall understanding of the IMS as an integrated component of the space station.

Force induced DNA melting

International Nuclear Information System (INIS)

Santosh, Mogurampelly; Maiti, Prabal K

2009-01-01

When pulled along the axis, double-strand DNA undergoes a large conformational change and elongates by roughly twice its initial contour length at a pulling force of about 70 pN. The transition to this highly overstretched form of DNA is very cooperative. Applying a force perpendicular to the DNA axis (unzipping), double-strand DNA can also be separated into two single-stranded DNA, this being a fundamental process in DNA replication. We study the DNA overstretching and unzipping transition using fully atomistic molecular dynamics (MD) simulations and argue that the conformational changes of double-strand DNA associated with either of the above mentioned processes can be viewed as force induced DNA melting. As the force at one end of the DNA is increased the DNA starts melting abruptly/smoothly above a critical force depending on the pulling direction. The critical force f m , at which DNA melts completely decreases as the temperature of the system is increased. The melting force in the case of unzipping is smaller compared to the melting force when the DNA is pulled along the helical axis. In the case of melting through unzipping, the double-strand separation has jumps which correspond to the different energy minima arising due to sequence of different base pairs. The fraction of Watson-Crick base pair hydrogen bond breaking as a function of force does not show smooth and continuous behavior and consists of plateaus followed by sharp jumps.

Melting in super-earths.

Science.gov (United States)

Stixrude, Lars

2014-04-28

We examine the possible extent of melting in rock-iron super-earths, focusing on those in the habitable zone. We consider the energetics of accretion and core formation, the timescale of cooling and its dependence on viscosity and partial melting, thermal regulation via the temperature dependence of viscosity, and the melting curves of rock and iron components at the ultra-high pressures characteristic of super-earths. We find that the efficiency of kinetic energy deposition during accretion increases with planetary mass; considering the likely role of giant impacts and core formation, we find that super-earths probably complete their accretionary phase in an entirely molten state. Considerations of thermal regulation lead us to propose model temperature profiles of super-earths that are controlled by silicate melting. We estimate melting curves of iron and rock components up to the extreme pressures characteristic of super-earth interiors based on existing experimental and ab initio results and scaling laws. We construct super-earth thermal models by solving the equations of mass conservation and hydrostatic equilibrium, together with equations of state of rock and iron components. We set the potential temperature at the core-mantle boundary and at the surface to the local silicate melting temperature. We find that ancient (∼4 Gyr) super-earths may be partially molten at the top and bottom of their mantles, and that mantle convection is sufficiently vigorous to sustain dynamo action over the whole range of super-earth masses.

Microstructural and mechanical characterization of melt spun process Sn-3.5Ag and Sn-3.5Ag-xCu lead-free solders for low cost electronic assembly

Energy Technology Data Exchange (ETDEWEB)

Mostafa Shalaby, Rizk; Kamal, Mustafa [Metal Physics Laboratory, Physics Department, Faculty of Science, Mansoura University, P.O.Box: 35516, Mansoura (Egypt); Ali, Esmail A.M. [Basic Science Department, Faculty of Engineering, University of Science & Technology (Yemen); Gumaan, Mohammed S., E-mail: m.gumaan1@gmail.com [Metal Physics Laboratory, Physics Department, Faculty of Science, Mansoura University, P.O.Box: 35516, Mansoura (Egypt); Basic Science Department, Faculty of Engineering, University of Science & Technology (Yemen)

2017-04-06

This paper aims to investigate the reliability of mechanical and creep behavior for the eutectic Sn-Ag and Sn-Ag-Cu Solder joints rapidly solidified after hot compressing (HC) in terms of structural changes and its relationship with thermal behavior, which has been discussed and compared with their properties before HC process by Mustafa et al. (2016) . These solder joints were prepared by melt-spinning technique and tested by HC at 30 MPa pressure and 150 °C for 90 min, their structural, mechanical and thermal properties after HC process have been investigated by X-ray diffraction (XRD), dynamic resonance techniques (DRT) and differential scanning calorimetry (DSC) techniques respectively and compared with these solders before HC. The results revealed that the pressure caused some fractures on the solders morphology surfaces. But some benefits for these solders have been occurred, like eliminating the internal stresses through recrystallization process whose evidence by the particle size increases after they HC, stabilized structure after HC was due to the metastable phases rearrangements, new intermetallic compounds (IMCs) formation, decreasing, melting temperature range (∆T), lattice strains (ƹ) and entropy change (S). These sequential benefits are considered to be the main reasons which lead to decreasing energy loss (Q{sup −1}), creep rate (É›) and thermal stability enhancement. Elastic modulus increment might be due to low elastic lattice distortions after HC, while the stress exponent (n) reduction refers to viscous glide mechanism of deformation after HC instead of climb deformation mechanism before HC.

Grand Prix Eurovision: Eine Fankultur im Medienzeitalter

Directory of Open Access Journals (Sweden)

Heinz Moser

2017-06-01

Full Text Available Der Grand Prix Eurovision ist seit Jahrzehnten eine der bekanntesten Unterhaltungssendungen im europäischen Raum. Dennoch erregte es Verwunderung, wenn der Schreibende Bekannten darüber berichtete, daß dies ein Forschungsgegenstand sei. Wurde von Interviews mit Grand Prix-Fans erzählt, so fielen schnell Aussagen wie: „Wie kann man sich nur für so etwas Abseitiges und Triviales wie den Grand Prix interessieren“. Dennoch bin ich der Meinung, daß Fankulturen für die entstehende Mediengesellschaft ein nicht unwichtiges Forschungsthema darstellen. Zwar geht es nicht um eine medienpädagogische Fragestellung im engeren Sinne; die Fans des Grand Prix Eurovision sind dem Jugendalter längst entwachsen. Dennoch handelt es sich bei Fangemeinschaften um Phänomene, die im Rahmen von Jugend- und Kinderkulturen von besonderer Relevanz sind. So meint Winter (1997, daß jugendliche Fanwelten eine bedeutende Rolle als Kristallisationspunkte kultureller Differenzierung spielen: ,Die Zugehörigkeit zu einer Fan weit ist Teil der jugendlichen Lebensbewältigung in der Postmoderne, denn in der Gemeinschaft der Fans können Jugendliche emotionale Allianzen eingehen, außeralltäglichen Beschäftigungen nachgehen, expressive Identitätsmuster gemeinschaftlich realisieren und sich mit ihrer Lebenssituation als Heranwachsende auseinandersetzen“ (Winter 1997, S. 51f..

Effect of boron addition to the hard magnetic bulk Nd60Fe30Al10 amorphous alloy

International Nuclear Information System (INIS)

Kong, H.Z.; Li, Y.; Ding, J.

2000-01-01

A detailed study of the effect of boron addition to crystallinity, magnetic properties and thermal properties was carried out for alloys Nd 60-x Fe 30 Al 10 B x with x=0, 1, 3 and 5 produced by copper mold chill casting and melt-spinning. The cast rods of alloys Nd 60-x Fe 30 Al 10 B x were largely amorphous. Remanence up to 0.154 T and coercivity up to 355 kA/m were observed, which were higher than those of the bulk amorphous Nd 60 Fe 30 Al 10 rod of the same diameter. A step in hysteresis loop was observed for the hard magnetic cast rod and ribbon melt-spun at a low speed of 5 m/s of the alloys with boron addition. Consistent increase in the amplitude of the step and magnetic field (H) at which the step was observed as the boron content increased. A single magnetic phase with low coercivity was observed for fully amorphous ribbon melt-spun at high speed of 30 m/s. Full crystallization due to heat treatment resulted in transition of hard magnetic amorphous phase of Nd 55 Fe 30 Al 10 B 5 cast rod to paramagnetic crystalline phases. TEM results of the as-cast rods illustrated the existence of numerous minute Nd-crystallites in amorphous matrix

Effect of wheel speed and annealing temperature on microstructure and texture evolution of Ni{sub 45}Mn{sub 36.6}In{sub 13.4}Co{sub 5} ribbon

Energy Technology Data Exchange (ETDEWEB)

Feng, Yan, E-mail: yanfeng@nwpu.edu.cn [State Key Laboratory of Solidification Processing Northwestern Polytechnical University, Xi' an, Shaanxi 710072 (China); Chen, Hong [State Key Laboratory of Solidification Processing Northwestern Polytechnical University, Xi' an, Shaanxi 710072 (China); Gao, Li [College of Engineering Science and Technology, Shanghai Ocean University, Shanghai 201306 (China); Wang, Haibo [College of Physics and Electronic Engineering, Taizhou University, Taizhou, Zhejiang 318000 (China); Bian, Xiaohai; Gong, Mingjie [State Key Laboratory of Solidification Processing Northwestern Polytechnical University, Xi' an, Shaanxi 710072 (China)

2016-12-15

Ni{sub 45}Mn{sub 36.6}In{sub 13.4}Co{sub 5} magnetic shape memory alloy was successfully produced as preferentially textured ribbon by melting spinning with different wheel speed. X-ray diffraction (XRD) and electron back scatter diffraction (EBSD) were used to study structure and texture evolution of these melt-spun ribbons. The thickness of melt-spun ribbon is 42 μm, 65 μm and 30 μm depending on wheel speed of 1 0 m/s, 15 m/s and 20 m/s, respectively. Density of α fiber texture (〈100〉//ND) vary with wheel speed changes, and is most intensive in the ribbon with wheel speed of 15 m/s. Grains of the ribbons grow after being annealed at 873 K, 973 K, 1073 K and 1173 K, recrystallization was not observed in ribbons after being annealed at 873 K but occurred in ribbons after being annealed at higher temperatures. The α fiber texture becomes weaker to some extent after annealing at different temperatures, due to new recrystallization texture formed at the process of annealing. - Highlights: •Sectional part of shape memory ribbon is firstly investigated by EBSD method. •Thickness and texture of ribbons vary with wheel speed. •Annealing temperature affect texture and microstructure evolution greatly. •Recrystallization textures were observed in ribbons after being annealed.

Melting under shock compression

International Nuclear Information System (INIS)

Bennett, B.I.

1980-10-01

A simple model, using experimentally measured shock and particle velocities, is applied to the Lindemann melting formula to predict the density, temperature, and pressure at which a material will melt when shocked from room temperature and zero pressure initial conditions

Electric melting furnace of solidifying radioactive waste by utilizing magnetic field and melting method

International Nuclear Information System (INIS)

Igarashi, Hiroshi.

1990-01-01

An electric melting furnace for solidification of radioactive wastes utilizing magnetic fields in accordance with the present invention comprises a plurality of electrodes supplying AC current to molten glass in a glass melting furnace and a plurality of magnetic poles for generating AC magnetic fields. Interactions between the current and the magnetic field, generated forces in the identical direction in view of time in the molten glass. That is, forces for promoting the flow of molten glass in the melting furnace are resulted due to the Fleming's left-hand rule. As a result, the following effects can be obtained. (1) The amount of heat ransferred from the molten glass to the starting material layer on the molten surface is increased to improve the melting performance. (2) For an identical melting performance, the size and the weight of the melting furnace can be reduced to decrease the amount of secondary wastes when the apparatus-life is exhausted. (3) Bottom deposits can be suppressed and prevented from settling and depositing to the reactor bottom by the promoted flow in the layer. (4) Further, the size of auxiliary electrodes for directly supplying electric current to heat the molten glass near the reactor bottom can be decreased. (I.S.)

Down-conversion IM-DD RF photonic link utilizing MQW MZ modulator.

Science.gov (United States)

Xu, Longtao; Jin, Shilei; Li, Yifei

2016-04-18

We present the first down-conversion intensity modulated-direct detection (IM-DD) RF photonic link that achieves frequency down-conversion using the nonlinear optical phase modulation inside a Mach-Zehnder (MZ) modulator. The nonlinear phase modulation is very sensitive and it can enable high RF-to-IF conversion efficiency. Furthermore, the link linearity is enhanced by canceling the nonlinear distortions from the nonlinear phase modulation and the MZ interferometer. Proof-of-concept measurement was performed. The down-conversion IM-DD link demonstrated 28dB improvement in distortion levels over that of a conventional IM-DD link using a LiNbO3 MZ modulator.

Results from an Interval Management (IM) Flight Test and Its Potential Benefit to Air Traffic Management Operations

Science.gov (United States)

Baxley, Brian; Swieringa, Kurt; Berckefeldt, Rick; Boyle, Dan

2017-01-01

NASA's first Air Traffic Management Technology Demonstration (ATD-1) subproject successfully completed a 19-day flight test of an Interval Management (IM) avionics prototype. The prototype was built based on IM standards, integrated into two test aircraft, and then flown in real-world conditions to determine if the goals of improving aircraft efficiency and airport throughput during high-density arrival operations could be met. The ATD-1 concept of operation integrates advanced arrival scheduling, controller decision support tools, and the IM avionics to enable multiple time-based arrival streams into a high-density terminal airspace. IM contributes by calculating airspeeds that enable an aircraft to achieve a spacing interval behind the preceding aircraft. The IM avionics uses its data (route of flight, position, etc.) and Automatic Dependent Surveillance-Broadcast (ADS-B) state data from the Target aircraft to calculate this airspeed. The flight test demonstrated that the IM avionics prototype met the spacing accuracy design goal for three of the four IM operation types tested. The primary issue requiring attention for future IM work is the high rate of IM speed commands and speed reversals. In total, during this flight test, the IM avionics prototype showed significant promise in contributing to the goals of improving aircraft efficiency and airport throughput.

A critical analysis of Sorrell v. IMS Health, Inc.: Pandora's box at best.

Science.gov (United States)

Bibet-Kalinyak, Isabelle

2012-01-01

Sorrell v. IMS Health, Inc. ("IMS Health"), a remarkable health care case with resounding First Amendment and economic repercussions, features the clashing interests of the State of Vermont and aggressive free market players from the pharmaceutical and data mining industries in a constitutional battle over Free Speech. In 2007, Vermont enacted Act 80, The Confidentiality of Prescription Information Act, prohibiting the sale, disclosure, and use of pharmacy records. Together with two other data miners and PhRMA, an association of brand-name drug manufacturers, IMS Health successfully challenged the constitutionality of Act 80 on First Amendment grounds. This article examines the legal arguments of IMS Health and Act 80 and analyzes why IMS Health stands out for potentially challenging the traditional doctrine of commercial speech and the resulting legal implications. After reviewing the Supreme Court's reasoning, the article concludes that, although the Supreme Court reached the appropriate outcome, it did so by unjustifiably departing from the established legal doctrine of commercial speech and the American tradition of consumer protection. At best, IMS Health's reasoning opens a legal Pandora's Box potentially leading to an onset of new commercial speech challenges; at worst, it manufactured a Trojan Horse aimed at eroding the traditional regulatory safeguards that maintain a balance between the needs of consumers and corporations alike.

Innovative Techniken und Algorithmen im Bereich Computational-Finance und Risikomanagement

OpenAIRE

Liang, Qian

2012-01-01

Diese Dissertation besteht aus zwei aktuellen Themen im Bereich Finanzmathematik, die voneinander unabhängig sind. Beim ersten Thema, "Flexible Algorithmen zur Bewertung komplexer Optionen mit mehreren Eigenschaften mittels der funktionalen Programmiersprache Haskell", handelt es sich um ein interdisziplinäres Projekt, in dem eine wissenschaftliche Brücke zwischen der Optionsbewertung und der funktionalen Programmierung geschlagen wurde. Im diesem Projekt wurde eine funktionale Biblio...

Die Raumdarstellung im erzählenden Werk um 1900

OpenAIRE

Lu, Xiaoli

2011-01-01

In der Literatur existiert eine eigene Welt, die mit Raum und Zeit verbunden ist. Im 19. Jahrhundert gewinnen beide, Raum und Zeit, an Bedeutung als bewusst eingesetzte Gestaltungselemente. Es bilden sich zwei Grundrichtungen heraus, eine mit dem Erzählgeschehen verknüpfte Semantisierung in der Klassik und in der Romantik und eine betonte Fixierung des Geschehens in der realen Welt durch genaue Zeit- und Ortsangaben im Realismus. Die Semantisierung von Raum und Zeit führt zu einer Bedeutungss...

[Das Bild und die Wahrnehmung der Stadt und der städtischen Gesellschaft im Hanseraum im Mittelalter und in der frühen Neuzeit] / Juhan Kreem

Index Scriptorium Estoniae

Kreem, Juhan

2009-01-01

Arvustus: Das Bild und die Wahrnehmung der Stadt und der städtischen Gesellschaft im Hanseraum im Mittelalter und in der frühen Neuzeit. hrsg. v. Roman Czaja. Torun, 2004. Torunis 2002. aastal toimunud konverentsi materjalid. Projekti "Pilt ja linn" raames ilmunud publikatsioonide loendit saab näha aadressil http://www.historiaurbium.org/english/attivita_images_en.html.

Melting in trivalent metal chlorides

International Nuclear Information System (INIS)

Saboungi, M.L.; Price, D.L.; Scamehorn, C.; Tosi, M.P.

1990-11-01

We report a neutron diffraction study of the liquid structure of YCl 3 and combine the structural data with macroscopic melting and transport data to contrast the behaviour of this molten salt with those of SrCl 2 , ZnCl 2 and AlCl 3 as prototypes of different melting mechanisms for ionic materials. A novel melting mechanism for trivalent metal chlorides, leading to a loose disordered network of edge-sharing octahedral units in the liquid phase, is thereby established. The various melting behaviours are related to bonding character with the help of Pettifor's phenomenological chemical scale. (author). 25 refs, 4 figs, 3 tabs

IMS Mitigation Target Areas - 2010 [ds673

Data.gov (United States)

California Natural Resource Agency — Mitigation Target Areas (MTA) were developed by the California Department of Fish and Game for the Interim Mitigation Strategy (IMS). The MTAs are an identification...

High performance electrochemical and electrothermal artificial muscles from twist-spun carbon nanotube yarn

Science.gov (United States)

Lee, Jae Ah; Baughman, Ray H.; Kim, Seon Jeong

2015-04-01

High performance torsional and tensile artificial muscles are described, which utilize thermally- or electrochemically-induced volume changes of twist-spun, guest-filled, carbon nanotube (CNT) yarns. These yarns were prepared by incorporating twist in carbon nanotube sheets drawn from spinnable CNT forests. Inserting high twist into the CNT yarn results in yarn coiling, which can dramatically amplify tensile stroke and work capabilities compared with that for the non-coiled twisted yarn. When electrochemically driven in a liquid electrolyte, these artificial muscles can generate a torsional rotation per muscle length that is over 1000 times higher than for previously reported torsional muscles. All-solid-state torsional electrochemical yarn muscles have provided a large torsional muscle stroke (53° per mm of yarn length) and a tensile stroke of up to 1.3% when lifting loads that are ~25 times heavier than can be lifted by the same diameter human skeletal muscle. Over a million torsional and tensile actuation cycles have been demonstrated for thermally powered CNT hybrid yarns muscles filled with paraffin wax, wherein a muscle spins a rotor at an average 11,500 revolutions/minute or delivers 3% tensile contraction at 1200 cycles/minute. At lower actuation rates, these thermally powered muscles provide tensile strokes of over 10%.

An optical microscopy study of the swelling of wet-spun films of CsDNA as a function of hydration and CsCl concentration

Science.gov (United States)

Schwenker, Megan; Marlowe, Robert; Lee, Scott; Rupprecht, Allan

2005-03-01

Highly oriented, wet-spun films of DNA expand in the direction perpendicular to the helical axis as the hydration of the film is increased. CsDNA films with a high CsCl content show an unexpected shrinkage at a relative humidity of 92%. Our most recent experiments have been to measure the perpendicular dimension of CsDNA as a function of both hydration and concentration of CsCl. Our preliminary results show that no shrinkage is observed at low contents of CsCl, showing that the CsCl plays an integral role in the shrinkage phenomenon.

Premixing and steam explosion phenomena in the tests with stratified melt-coolant configuration and binary oxidic melt simulant materials

Energy Technology Data Exchange (ETDEWEB)

Kudinov, Pavel, E-mail: pavel@safety.sci.kth.se; Grishchenko, Dmitry, E-mail: dmitry@safety.sci.kth.se; Konovalenko, Alexander, E-mail: kono@kth.se; Karbojian, Aram, E-mail: karbojan@kth.se

2017-04-01

Highlights: • Steam explosion in stratified melt-coolant configuration is studied experimentally. • Different binary oxidic melt simulant materials were used. • Five spontaneous steam explosions were observed. • Instability of melt-coolant interface and formation of premixing layer was observed. • Explosion strength is influenced by melt superheat and water subcooling. - Abstract: Steam explosion phenomena in stratified melt-coolant configuration are considered in this paper. Liquid corium layer covered by water on top can be formed in severe accident scenarios with (i) vessel failure and release of corium melt into a relatively shallow water pool; (ii) with top flooding of corium melt layer. In previous assessments of potential energetics in stratified melt-coolant configuration, it was assumed that melt and coolant are separated by a stable vapor film and there is no premixing prior to the shock wave propagation. This assumption was instrumental for concluding that the amount of energy that can be released in such configuration is not of safety importance. However, several recent experiments carried out in Pouring and Under-water Liquid Melt Spreading (PULiMS) facility with up to 78 kg of binary oxidic corium simulants mixtures have resulted in spontaneous explosions with relatively high conversion ratios (order of one percent). The instability of the melt-coolant interface, melt splashes and formation of premixing layer were observed in the tests. In this work, we present results of experiments carried out more recently in steam explosion in stratified melt-coolant configuration (SES) facility in order to shed some light on the premixing phenomena and assess the influence of the test conditions on the steam explosion energetics.

Melting of superheated molecular crystals

Science.gov (United States)

Cubeta, Ulyana; Bhattacharya, Deepanjan; Sadtchenko, Vlad

2017-07-01

Melting dynamics of micrometer scale, polycrystalline samples of isobutane, dimethyl ether, methyl benzene, and 2-propanol were investigated by fast scanning calorimetry. When films are superheated with rates in excess of 105 K s-1, the melting process follows zero-order, Arrhenius-like kinetics until approximately half of the sample has transformed. Such kinetics strongly imply that melting progresses into the bulk via a rapidly moving solid-liquid interface that is likely to originate at the sample's surface. Remarkably, the apparent activation energies for the phase transformation are large; all exceed the enthalpy of vaporization of each compound and some exceed it by an order of magnitude. In fact, we find that the crystalline melting kinetics are comparable to the kinetics of dielectric α-relaxation in deeply supercooled liquids. Based on these observations, we conclude that the rate of non-isothermal melting for superheated, low-molecular-weight crystals is limited by constituent diffusion into an abnormally dense, glass-like, non-crystalline phase.

Hinderniserkennung und -verfolgung mit einer PMD-kamera im automobil

Science.gov (United States)

Schamm, Thomas; Vacek, Stefan; Natroshvilli, Koba; Marius Zöllner, J.; Dillmann, Rüdiger

Die Detektion von Hindernissen vor dem Automobil ist eine Hauptanforderung an moderne Fahrerassistenzsysteme (FAS). In dieser Arbeit wird ein System vorgestellt, das mit Hilfe einer PMDKamera (Photomischdetektor) Hindernisse auf der Fahrspur erkennt und deren relevante Parameter bestimmt. Durch die PMD-Kamera werden zunächst 3D-Tiefenbilder der Fahrzeugumwelt generiert. Nach einem initialen Filterprozess werden im Tiefenbild mit Hilfe eines Bereichswachstumsverfahrens Hindernisse gesucht. Zur Stabilisierung des Verfahrens und zur Parameterberechnung wird ein Kaiman Filter eingesetzt. Das Ergebnis ist eine Liste aller Hindernisse im Fahrbereich des Automobils.

[Christian Westerhoff. Zwangsarbeit im Ersten Weltkrieg. Deutsche Arbeitskräftepolitik im besetzten Polen und Litauen 1914-1918, Tilman Plath.Zwischen Schonung und Menschenjagden. Die Arbeitseinsatzpolitik in den baltischen Generalbezirken des Reich

Index Scriptorium Estoniae

Hiio, Toomas, 1965-

2014-01-01

Arvustus: Westerhoff, Christian. Zwangsarbeit im Ersten Weltkrieg. Deutsche Arbeitskräftepolitik im besetzten Polen und Litauen 1914-1918 (Studien zur historischen Migrationsforschung, 25). Verlag Ferdinand Schöningh. Padeborn 2011

Pressure melting and ice skating

Science.gov (United States)

Colbeck, S. C.

1995-10-01

Pressure melting cannot be responsible for the low friction of ice. The pressure needed to reach the melting temperature is above the compressive failure stress and, if it did occur, high squeeze losses would result in very thin films. Pure liquid water cannot coexist with ice much below -20 °C at any pressure and friction does not increase suddenly in that range. If frictional heating and pressure melting contribute equally, the length of the wetted contact could not exceed 15 μm at a speed of 5 m/s, which seems much too short. If pressure melting is the dominant process, the water films are less than 0.08 μm thick because of the high pressures.

Toward an Intelligent Ion Mobility Spectrometer (IMS)

International Nuclear Information System (INIS)

McJunkin, Timothy R.; Scott, Jill R.; Miller, Carla J.

2003-01-01

The ultimate goal is to design and build a very smart ion mobility spectrometer (IMS) that can operate autonomously. To accomplish this, software capable of interpreting spectra so that it can be used in control loops for data interpretation as well as adjusting instrument parameters is being developed. Fuzzy logic and fuzzy numbers are used in this IMS spectra classification scheme. Fuzzy logic provides a straight forward method for developing a classification/detection system, whenever rules for classifying the spectra can be described linguistically. Instead of using 'max' and 'min' values, the product of the truth values is used to determine class membership. Using the product allows rule-bases that utilize the AND function to allow each condition to discount truth value in determining membership, while rule-bases with an OR function are allowed to accumulate membership. Fuzzy numbers allow encapsulation of the uncertainties due to ion mobility peak widths as well as measured instrumental parameters, such as pressure and temperature. Associating a peak with a value of uncertainty, in addition to making adjustments to the mobility calculation based on variations in measured parameters, enables unexpected shifts to be more reliably detected and accounted for; thereby, reducing the opportunity for 'false negative' results. The measure of uncertainty is anticipated to serve the additional purpose of diagnosing the operational conditions of the IMS instrument.

Improved detection of Mycobacterium bovis infection in bovine lymph node tissue using immunomagnetic separation (IMS-based methods.

Directory of Open Access Journals (Sweden)

Linda D Stewart

Full Text Available Immunomagnetic separation (IMS can selectively isolate and concentrate Mycobacterium bovis cells from lymph node tissue to facilitate subsequent detection by PCR (IMS-PCR or culture (IMS-MGIT. This study describes application of these novel IMS-based methods to test for M. bovis in a survey of 280 bovine lymph nodes (206 visibly lesioned (VL, 74 non-visibly lesioned (NVL collected at slaughter as part of the Northern Ireland bovine TB eradication programme. Their performance was evaluated relative to culture. Overall, 174 (62.1% lymph node samples tested positive by culture, 162 (57.8% by IMS-PCR (targeting IS6110, and 191 (68.2% by IMS-MGIT culture. Twelve (6.9% of the 174 culture positive lymph node samples were not detected by either of the IMS-based methods. However, an additional 79 M. bovis positive lymph node samples (27 (13.1% VL and 52 (70.3% NVL were detected by the IMS-based methods and not by culture. When low numbers of viable M. bovis are present in lymph nodes (e.g. in NVLs of skin test reactor cattle decontamination prior to culture may adversely affect viability, leading to false negative culture results. In contrast, IMS specifically captures whole M. bovis cells (live, dead or potentially dormant which are not subject to any deleterious treatment before detection by PCR or MGIT culture. During this study only 2.7% of NVL lymph nodes tested culture positive, whereas 70.3% of the same samples tested M. bovis positive by the IMS-based tests. Results clearly demonstrate that not only are the IMS-based methods more rapid but they have greater detection sensitivity than the culture approach currently used for the detection of M. bovis infection in cattle. Adoption of the IMS-based methods for lymph node testing would have the potential to improve M. bovis detection in clinical samples.

Die emotionale Dimension während der Sprechproduktion im Fremdsprachenlernprozess

Directory of Open Access Journals (Sweden)

Bahar İŞİGÜZEL

2017-12-01

Full Text Available Die Gefühle bzw. Emotionen der Lernenden beim Fremdsprachenlehr- und Lernprozess spielen eine wichtige Rolle. Mit der Verknüpfung der Emotion und Kognition beim Lernprozess, haben die positiven Gefühle eine große Bedeutung für den Lernerfolg. Als eine produktive Fertigkeit hat das Sprechen eine wesentlich intensive Beziehung mit den Emotionen, weil es in der realen Zeit fließend laufen muss. Der Lernende soll bei der Sprechproduktion spontan die richtigen Wörter auf die richtige Art und Weise anwenden und sie auch noch verständlich aussprechen. Leider erreicht die Sprechfertigkeit meistens eine niedrigere Niveaustufe als die anderen drei (Schreiben, Lesen und Hören Fertigkeiten im Fremdsprachenunterrichtprozess. Diese qualitative Untersuchung konzentriert sich auf die Daten (Tonaufnahme, die anhand eines Interviews während einer Sprechproduktionsübung im universitären Fremdsprachenunterricht gesammelt wurden. Um die emotionale Dimension der Lernenden während der Sprechproduktion zu identifizieren, wurden im Einzelinterview die Frage „Wie fühlst du dich während du eine Fremdsprache (Englisch sprichst?“ gestellt. Die Teilnehmer dieser Untersuchung waren 29 Studenten, die im WS 2016 - 2017 an Universität Nevşehir Hacı Bektaş Veli (Türkei immatrikuliert waren. Die Auswertung des Interviews folgte mit einer Transkription und einer Interpretation der Tonaufnahmen. Die Meinungen zu der emotionalen Dimension während der Sprechproduktion der Studenten wurden kategorisiert. Die Resultate dieser qualitativen Untersuchung zeigen, dass die emotionale Dimension der Lernenden im universitären Kontext sich in drei Kategorien (positiv, negativ und frühere Ausbildung verteilen.

Ferromagnetic bulk glassy alloys

International Nuclear Information System (INIS)

Inoue, Akihisa; Makino, Akihiro; Mizushima, Takao

2000-01-01

This paper deals with the review on the formation, thermal stability and magnetic properties of the Fe-based bulk glassy alloys in as-cast bulk and melt-spun ribbon forms. A large supercooled liquid region over 50 K before crystallization was obtained in Fe-(Al, Ga)-(P, C, B, Si), Fe-(Cr, Mo, Nb)-(Al, Ga)-(P, C, B) and (Fe, Co, Ni)-Zr-M-B (M=Ti, Hf, V, Nb, Ta, Cr, Mo and W) systems and bulk glassy alloys were produced in a thickness range below 2 mm for the Fe-(Al, Ga)-(P, C, B, Si) system and 6 mm for the Fe-Co-(Zr, Nb, Ta)-(Mo, W)-B system by copper-mold casting. The ring-shaped glassy Fe-(Al, Ga)-(P, C, B, Si) alloys exhibit much better soft magnetic properties as compared with the ring-shaped alloy made from the melt-spun ribbon because of the formation of the unique domain structure. The good combination of high glass-forming ability and good soft magnetic properties indicates the possibility of future development as a new bulk glassy magnetic material

The IMS Software Integration Platform

Science.gov (United States)

1993-04-12

products to incorporate all data shared by the IMS applications. Some entities (time-series, images, a algorithm -specific parameters) must be managed...dbwhoanii, dbcancel Transaction Management: dbcommit, dbrollback Key Counter Assignment: dbgetcounter String Handling: cstr ~to~pad, pad-to- cstr Error...increment *value; String Maniputation: int cstr topad (array, string, arraylength) char *array, *string; int arrayjlength; int pad tocstr (string

Filament stretching rheometry of polymer melts

DEFF Research Database (Denmark)

Hassager, Ole; Nielsen, Jens Kromann; Rasmussen, Henrik Koblitz

2005-01-01

The Filament Stretching Rheometry (FSR) method developed by Sridhar, McKinley and coworkers for polymer solutions has been extended to be used also for polymer melts. The design of a melt-FSR will be described and differences to conventional melt elongational rheometers will be pointed out. Results...

Biomechanisch-kinemetrische Bewegungsanalyse und Ansätze zur Bewegungssteuerung für ein Training im Wellenreiten

OpenAIRE

Matschkur, Tina

2008-01-01

Neben der biomechanisch-kinemetrischen Bewegungsanalyse einzelner ausgewählter Techniken im Wellenreiten beschäftigt sich diese Dissertation auch ansatzweise im Rahmen einer elektromyographischen Fallstudie mit der muskulären Koordination bei der Bewegungsausführung im Surfen, um daraus Schlussfolgerungen für das Training im Wellenreiten treffen zu können. Ein geschichtlicher und wissenschaftlicher Überblick über das Wellenreiten leitet das Thema ein und macht somit auf die besondere Ausgangs...

Eisengehalt von Fleisch - Ermittlung des Eisengehalts im Fleisch verschiedener Tierarten

OpenAIRE

Westphal, Karsten; Klose, Ralf; Golze, Manfred

2009-01-01

Der Bericht beinhaltet Ergebnisse von Fleischuntersuchungen auf den Eisengehalt. Untersucht wurden 308 Schweinefleischproben und etwa 300 Fleischproben der Tierarten Rind, Bison, Auerochse, Büffel, Schaf, Ziege, Kaninchen, Wildschwein, Rehwild, Rotwild und Fasan. Die sächsischen Ergebnisse bestätigen Untersuchungen anderer Bundesländer und belegen den starken Rückgang des Eisengehaltes im Schweinefleisch. Er lag im Mittel bei 4,1 mg/kg Frischmasse (FM). Vor 30 Jahren lag der Eisengehalt...

Quad-Polarization Transmission for High-Capacity IM/DD Links

DEFF Research Database (Denmark)

Estaran Tolosa, Jose Manuel; Castaneda, Mario A. Usuga; Porto da Silva, Edson

2014-01-01

We report the first experimental demonstration of IM/DD links usi ng four states of polarization. Fiber - Induced polarization rotation is compensated with a simple tracking algorithm operating on the Stokes space. The principle is prove n at 128 Gb/s over 2 - km SSMF......We report the first experimental demonstration of IM/DD links usi ng four states of polarization. Fiber - Induced polarization rotation is compensated with a simple tracking algorithm operating on the Stokes space. The principle is prove n at 128 Gb/s over 2 - km SSMF...

Melting temperature of graphite

International Nuclear Information System (INIS)

Korobenko, V.N.; Savvatimskiy, A.I.

2001-01-01

Full Text: Pulse of electrical current is used for fast heating (∼ 1 μs) of metal and graphite specimens placed in dielectric solid media. Specimen consists of two strips (90 μm in thick) placed together with small gap so they form a black body model. Quasy-monocrystal graphite specimens were used for uniform heating of graphite. Temperature measurements were fulfilled with fast pyrometer and with composite 2-strip black body model up to melting temperature. There were fulfilled experiments with zirconium and tungsten of the same black body construction. Additional temperature measurements of liquid zirconium and liquid tungsten are made. Specific heat capacity (c P ) of liquid zirconium and of liquid tungsten has a common feature in c P diminishing just after melting. It reveals c P diminishing after melting in both cases over the narrow temperature range up to usual values known from steady state measurements. Over the next wide temperature range heat capacity for W (up to 5000 K) and Zr (up to 4100 K) show different dependencies of heat capacity on temperature in liquid state. The experiments confirmed a high quality of 2-strip black body model used for graphite temperature measurements. Melting temperature plateau of tungsten (3690 K) was used for pyrometer calibration area for graphite temperature measurement. As a result, a preliminary value of graphite melting temperature of 4800 K was obtained. (author)

Theoretical melting curve of caesium

International Nuclear Information System (INIS)

Simozar, S.; Girifalco, L.A.; Pennsylvania Univ., Philadelphia

1983-01-01

A statistical-mechanical model is developed to account for the complex melting curve of caesium. The model assumes the existence of three different species of caesium defined by three different electronic states. On the basis of this model, the free energy of melting and the melting curve are computed up to 60 kbar, using the solid-state data and the initial slope of the fusion curve as input parameters. The calculated phase diagram agrees with experiment to within the experimental error. Other thermodynamic properties including the entropy and volume of melting were also computed, and they agree with experiment. Since the theory requires only one adjustable constant, this is taken as strong evidence that the three-species model is satisfactory for caesium. (author)

Mantle melting and melt refertilization beneath the Southwest Indian Ridge: Mineral composition of abyssal peridotites

Science.gov (United States)

Chen, Ling; Zhu, Jihao; Chu, Fengyou; Dong, Yan-hui; Liu, Jiqiang; Li, Zhenggang; Zhu, Zhimin; Tang, Limei

2017-04-01

As one of the slowest spreading ridges of the global ocean ridge system, the Southwest Indian Ridge (SWIR) is characterized by discontinued magmatism. The 53°E segment between the Gallieni fracture zone (FZ) (52°20'E) and the Gazelle FZ (53°30'E) is a typical amagmatic segment (crustal thickness 1cm) Opx, and Mg-rich mineral compositions akin to harzburgite xenoliths that sample old continental lithospheric mantle (Kelemen et al., 1998). Melt refertilization model shows that Group 2 peridotites were affected by an enriched low-degree partial melt from the garnet stability field. These results indicate that depleted mantle which experiences ancient melting event are more sensitive to melt refertilization, thus may reduce the melt flux, leading to extremely thin crust at 53°E segment. This research was granted by the National Basic Research Programme of China (973 programme) (grant No. 2013CB429705) and the Fundamental Research Funds of Second Institute of Oceanography, State Oceanic Administration (JG1603, SZ1507). References: Johnson K T M, Dick H J B, Shimizu N. Melting in the oceanic upper mantle: An ion microprobe study of diopsides in abyssal peridotites[J]. Journal of Geophysical Research, 1990, 95(B3):2661-2678. Kelemen P B, Hart S R, Bernstein S. Silica enrichment in the continental upper mantle via melt/rock reaction[J]. Earth & Planetary Science Letters, 1998, 164(1-2):387-406. Zhou H, Dick H J. Thin crust as evidence for depleted mantle supporting the Marion Rise.[J]. Nature, 2013, 494(7436):195-200.

Melts of garnet lherzolite: experiments, models and comparison to melts of pyroxenite and carbonated lherzolite

Science.gov (United States)

Grove, Timothy L.; Holbig, Eva S.; Barr, Jay A.; Till, Christy B.; Krawczynski, Michael J.

2013-01-01

Phase equilibrium experiments on a compositionally modified olivine leucitite from the Tibetan plateau have been carried out from 2.2 to 2.8 GPa and 1,380–1,480 °C. The experiments-produced liquids multiply saturated with spinel and garnet lherzolite phase assemblages (olivine, orthopyroxene, clinopyroxene and spinel ± garnet) under nominally anhydrous conditions. These SiO2-undersaturated liquids and published experimental data are utilized to develop a predictive model for garnet lherzolite melting of compositionally variable mantle under anhydrous conditions over the pressure range of 1.9–6 GPa. The model estimates the major element compositions of garnet-saturated melts for a range of mantle lherzolite compositions and predicts the conditions of the spinel to garnet lherzolite phase transition for natural peridotite compositions at above-solidus temperatures and pressures. We compare our predicted garnet lherzolite melts to those of pyroxenite and carbonated lherzolite and develop criteria for distinguishing among melts of these different source types. We also use the model in conjunction with a published predictive model for plagioclase and spinel lherzolite to characterize the differences in major element composition for melts in the plagioclase, spinel and garnet facies and develop tests to distinguish between melts of these three lherzolite facies based on major elements. The model is applied to understand the source materials and conditions of melting for high-K lavas erupted in the Tibetan plateau, basanite–nephelinite lavas erupted early in the evolution of Kilauea volcano, Hawaii, as well as younger tholeiitic to alkali lavas from Kilauea.

Gel Spun PAN/CNT Based Carbon Fibers with Honey-Comb Cross-Section

Science.gov (United States)

2013-11-13

samples were prepared by mounting a single filament on a copper 3-post TEM grid (Omniprobe) and curing in epoxy (Gatan). The carbon fiber was then... Kevlar ® 49 [28], Zylon® [29], T300 [2], IM10 [30], M60J [31], YS-95A [32] were obtained from the data sheets of these fibers from the respective...made contained 60 vol% fibers in epoxy matrix. Fiber compressive strength may be dependent on fiber structure as well as fiber geometry. Kumar et al

Microstructure, texture, and magnetic properties of backward extruded NdFeB ring magnets

International Nuclear Information System (INIS)

Gruenberger, W.; Hinz, D.; Schlaefer, D.; Schultz, L.

1996-01-01

Radially-oriented NdFeB ring magnets have been prepared by backward extrusion of melt-spun material. The average remanence measured in the radial direction reaches values above 1.2 T. Due to the inhomogeneity of the deformation, the magnetic properties and X-ray diffraction patterns revealed a gradual improvement of the alignment from the outer shell to regions near the inner surface of the ring. (orig.)

High field magnetisation studies in some rare earth based amorphous ribbons

Science.gov (United States)

Krishnan, R.; Lassri, H.; Driouch, L.

1995-02-01

We have carried out magnetisation studies at fields up to 20 T of melt spun amorphous Fe 72- xY xHo 8B 20 alloys. The approach to saturation for H ≤ 11 T has been analysed on the basis of Chudnovsky's model, and the exchange constant, random anisotropy etc. have been calculated. We have also extracted the local anisotropy from the coercivity.

Scientific Articles on Magnetic Materials and Applications Research from 2006 - 2014

Science.gov (United States)

2015-03-01

had coercivities less than 0.4 Oe and saturation inductions greater than 1Tesla. The electrical resistivities of the amorphous ribbons were all...S. Liu, S. Y. Chu, J. C. Horwath and R. T. Fingers, "Effects of Zr , Nb , and Cu substitutions on magnetic properties of melt-spun and hot deformed...DISTRIBUTION STATEMENT. *//Signature// //Signature// JOHN C. HORWATH THOMAS L. REITZ, Technical Advisor Electrical Engineer Mechanical

Female teams im eSport: Re-Konstruktion der Kategorie Geschlecht

OpenAIRE

Streubel, Anett

2010-01-01

"Das Ziel dieses Papers ist es, die Herausbildung von "female Teams" im eSport zu untersuchen. Das Hauptaugenmerk liegt hierbei auf Rekonstruktionsmechanismen der Kategorie Geschlecht, welche durch Sprache und Diskurse gebildet, erlernt und fortgeführt werden. Der Anteil der Spielerinnen, die das Computerspielen als Sport betreiben, wächst stetig an - deshalb soll in dieser Studie der Profibereich des eSport näher betrachtet werden. In einem Tätigkeitsfeld, in dem nicht der Körper im Mittelpu...

Zur mediopassiven 2. Und 3. Person dualis im indogermanischen

Directory of Open Access Journals (Sweden)

Bojan Čop

1972-12-01

Full Text Available Bekanntlich gibt es in einigen seltenen idg. Sprachen (im Arischen, Griechischen, Tocharischen auch Personal - suffixe für die 2. u n d 3. P. Du. des Mediopassivs. Von diesen sind die griechischen Ausgänge – 2. und 3. Du primär, 2. Du. sekundär, Du. sekundär sicher junge Neubildungen, s. z. B. Brugmann, Grdr.2 II 3 II, 657, § 602; Schwyzer, Gr. Gr. I 670, 672. Ein voll ausgebildetes System solcher Endungen besitzt das Arische; im Tocharischen kommt nur eine einzige Form mit solcher Endung vor, die die 2. P. Du. Med. lmperativi darstellt. Unter solchen Umständen scheint es schwierig, aus diesem Material wahrscheinliche Schlüsse für da_s Urindogermanische zu machen. Und doch ist gerade die tocharische Form, die uns eine ausserordentlich grosse Hilfe leistet, wenn man sie richtig zu beurteilen vermag. Die tocharische Endung, verbunden mit den arischen, wird unter Einschluss der allgemeinen Tendenzen und Regelungen im System der indogermanischen Personalsuffixe ohne Schwierigkeit die urindogermanische Urform erscheinen lassen.

[Glanz und Elend - Mythos und Wirklichkeit der Herrenhäuser im Baltikum] / Karsten Brüggemann

Index Scriptorium Estoniae

Brüggemann, Karsten, 1965-

2014-01-01

Arvustus: Glanz und Elend - Mythos und Wirklichkeit der Herrenhäuser im Baltikum. Hrsg. von Ilse von zur Mühlen im Auftrag der Carl-Schirren-Gesellschaft e.V. und des Ostpreußischen Landesmuseums Lüneburg. Kunstverlag Josef Fink. Lindenberg im Allgäu 2012

Season of infectious mononucleosis and risk of multiple sclerosis at different latitudes; the EnvIMS Study.

Science.gov (United States)

Lossius, Andreas; Riise, Trond; Pugliatti, Maura; Bjørnevik, Kjetil; Casetta, Ilaria; Drulovic, Jelena; Granieri, Enrico; Kampman, Margitta T; Landtblom, Anne-Marie; Lauer, Klaus; Magalhaes, Sandra; Myhr, Kjell-Morten; Pekmezovic, Tatjana; Wesnes, Kristin; Wolfson, Christina; Holmøy, Trygve

2014-05-01

Seasonal fluctuations in solar radiation and vitamin D levels could modulate the immune response against Epstein-Barr virus (EBV) infection and influence the subsequent risk of multiple sclerosis (MS). Altogether 1660 MS patients and 3050 controls from Norway and Italy participating in the multinational case-control study of Environmental Factors In Multiple Sclerosis (EnvIMS) reported season of past infectious mononucleosis (IM). IM was generally reported more frequently in Norway (p=0.002), but was associated with MS to a similar degree in Norway (odds ratio (OR) 2.12, 95% confidence interval (CI) 1.64-2.73) and Italy (OR 1.72, 95% CI 1.17-2.52). For all participants, there was a higher reported frequency of IM during spring compared to fall (p<0.0005). Stratified by season of IM, the ORs for MS were 1.58 in spring (95% CI 1.08-2.31), 2.26 in summer (95% CI 1.46-3.51), 2.86 in fall (95% CI 1.69-4.85) and 2.30 in winter (95% CI 1.45-3.66). IM is associated with MS independently of season, and the association is not stronger for IM during spring, when vitamin D levels reach nadir. The distribution of IM may point towards a correlation with solar radiation or other factors with a similar latitudinal and seasonal variation.

Material properties influence on steam explosion efficiency. Prototypic versus simulant melts, eutectic versus non-eutectic melts

International Nuclear Information System (INIS)

Leskovar, M.; Mavko, B.

2006-01-01

A steam explosion may occur during a severe nuclear reactor accident if the molten core comes into contact with the coolant water. A strong enough steam explosion in a nuclear power plant could jeopardize the containment integrity and so lead to a direct release of radioactive material to the environment. Details of processes taking place prior and during the steam explosion have been experimentally studied for a number of years with adjunct efforts in modelling these processes to address the scaling of these experiments. Steam explosion experiments have shown that there are important differences of behaviour between simulant and prototypical melts, and that also at prototypical melts the fuel coolant interactions depend on the composition of the corium. In experiments with prototypic materials no spontaneous steam explosions occurred (except with an eutectic composition), whereas with simulant materials the steam explosions were triggered spontaneously. The energy conversion ratio of steam explosions with prototypic melts is at least one order of magnitude lower than the energy conversion ratio of steam explosions with simulant melts. Although the different behaviour of prototypic and simulant melts has been known for a number of years, there is no reliable explanation for these differences. Consequently it is not possible to reliably estimate whether corium would behave so non-explosive also in reactor conditions, where the mass of poured melt is nearly three orders of magnitude larger than in experimental conditions. An even more fascinating material effect was observed recently at corium experiments with eutectic and non-eutectic compositions. It turned out that eutectic corium always exploded spontaneously, whereas non-eutectic corium never exploded spontaneously. In the paper, a possible explanation of both material effects (prototypic/simulant melts, eutectic/non-eutectic corium) on the steam explosion is provided. A model for the calculation of the

Numerical simulation of hot-melt extrusion processes for amorphous solid dispersions using model-based melt viscosity.

Science.gov (United States)

Bochmann, Esther S; Steffens, Kristina E; Gryczke, Andreas; Wagner, Karl G

2018-03-01

Simulation of HME processes is a valuable tool for increased process understanding and ease of scale-up. However, the experimental determination of all required input parameters is tedious, namely the melt rheology of the amorphous solid dispersion (ASD) in question. Hence, a procedure to simplify the application of hot-melt extrusion (HME) simulation for forming amorphous solid dispersions (ASD) is presented. The commercial 1D simulation software Ludovic ® was used to conduct (i) simulations using a full experimental data set of all input variables including melt rheology and (ii) simulations using model-based melt viscosity data based on the ASDs glass transition and the physical properties of polymeric matrix only. Both types of HME computation were further compared to experimental HME results. Variation in physical properties (e.g. heat capacity, density) and several process characteristics of HME (residence time distribution, energy consumption) among the simulations and experiments were evaluated. The model-based melt viscosity was calculated by using the glass transition temperature (T g ) of the investigated blend and the melt viscosity of the polymeric matrix by means of a T g -viscosity correlation. The results of measured melt viscosity and model-based melt viscosity were similar with only few exceptions, leading to similar HME simulation outcomes. At the end, the experimental effort prior to HME simulation could be minimized and the procedure enables a good starting point for rational development of ASDs by means of HME. As model excipients, Vinylpyrrolidone-vinyl acetate copolymer (COP) in combination with various APIs (carbamazepine, dipyridamole, indomethacin, and ibuprofen) or polyethylene glycol (PEG 1500) as plasticizer were used to form the ASDs. Copyright © 2017 Elsevier B.V. All rights reserved.

Melt processed high-temperature superconductors

CERN Document Server

1993-01-01

The achievement of large critical currents is critical to the applications of high-temperature superconductors. Recent developments have shown that melt processing is suitable for producing high J c oxide superconductors. Using magnetic forces between such high J c oxide superconductors and magnets, a person could be levitated.This book has grown largely out of research works on melt processing of high-temperature superconductors conducted at ISTEC Superconductivity Research Laboratory. The chapters build on melt processing, microstructural characterization, fundamentals of flux pinning, criti

Microstructure, mechanical and functional properties of NiTi-based shape memory ribbons

International Nuclear Information System (INIS)

Mehrabi, K.; Bruncko, M.; Kneissl, A.C.

2012-01-01

Highlights: ► Melt-spun samples exhibited martensite structure and shape memory effects immediately after processing at room temperature. ► Using a new etchant and interference contrast, it is possible to reveal the fine microstructures and grain boundaries. ► The martensite structure in NiTi is very fine, and nano-sized twin boundaries could be revealed using TEM only. ► Two-way effects have been successfully introduced by different thermomechanical training methods in NiTi, NiTiCu and NiTiW alloys, which can be used for several applications, e.g. microsensors and microactuators. - Abstract: The present work has been aimed to study the microstructures, functional properties and the influence of different thermomechanical training methods on the two-way shape memory effect in NiTi-based melt-spun ribbons. In order to get small-dimensioned shape memory alloys (SMAs) with good functional and mechanical properties, a rapid solidification technique was employed. Their fracture and elasticity characteristics have been determined, as well as shape memory properties by thermomechanical cycling. The ribbons were trained under tensile and bending deformation by thermal cycling through the phase transformation temperature range. The results displayed that all different training methods were effective in developing a two-way shape memory effect (TWSME). The influence of copper (5–25 at.% Cu) and tungsten (2 at.% W) on the microstructure, and the functional and mechanical behavior of NiTi thin ribbons was also investigated. All samples show a shape memory effect immediately after processing without further heat treatment. The melt-spun ribbons were trained under constant strain (bending and tensile deformation) by thermal cycling through the phase transformation temperature range. The addition of copper was effective to narrow the transformation hysteresis. The W addition has improved the TWSME stability of the NiTi alloys and mechanical properties. Results about

Finanzmärkte – Unternehmungen – Informationen: Ergebnisse des Projektes im Wintersemester 2016/2017

OpenAIRE

Geyer, Helmut; Grau, Svenja; Giersch, Peter; Eckardt, Maximilian; Eder, Josephin; Catholy, Victoria; Pisak, Anastasia; Löser, Matthias; Jehring, Maximilian; Zhang, Haoyang; Grabengießer, Anja; Gruschwitz, Karoline; Heinrich, Katharina; Patzer, Vivien; Päsler, Florian

2018-01-01

Der vorliegende Beitrag der Wirtschaftswissenschaftlichen Schriften ist ein Sammelband, der die Beiträge der Studierenden des 2. Fachsemesters im Masterstudiengang General Management aus dem Wintersemester 2016/2017 umfasst. Die Einzelbeiträge wurden in einer zwei Monate dauernden Projektarbeit im Herbst 2016 erarbeitet und im Januar 2017 präsentiert. Der Themenschwerpunkt für dieses Jahr lag auf dem Bereich "Immobilien/Wohnungspolitik". Innerhalb dieser Vorgabe wurde ein breites Spektrum bea...

The melting and solidification of nanowires

International Nuclear Information System (INIS)

Florio, B. J.; Myers, T. G.

2016-01-01

A mathematical model is developed to describe the melting of nanowires. The first section of the paper deals with a standard theoretical situation, where the wire melts due to a fixed boundary temperature. This analysis allows us to compare with existing results for the phase change of nanospheres. The equivalent solidification problem is also examined. This shows that solidification is a faster process than melting; this is because the energy transfer occurs primarily through the solid rather than the liquid which is a poorer conductor of heat. This effect competes with the energy required to create new solid surface which acts to slow down the process, but overall conduction dominates. In the second section, we consider a more physically realistic boundary condition, where the phase change occurs due to a heat flux from surrounding material. This removes the singularity in initial melt velocity predicted in previous models of nanoparticle melting. It is shown that even with the highest possible flux the melting time is significantly slower than with a fixed boundary temperature condition.

The melting and solidification of nanowires

Science.gov (United States)

Florio, B. J.; Myers, T. G.

2016-06-01

A mathematical model is developed to describe the melting of nanowires. The first section of the paper deals with a standard theoretical situation, where the wire melts due to a fixed boundary temperature. This analysis allows us to compare with existing results for the phase change of nanospheres. The equivalent solidification problem is also examined. This shows that solidification is a faster process than melting; this is because the energy transfer occurs primarily through the solid rather than the liquid which is a poorer conductor of heat. This effect competes with the energy required to create new solid surface which acts to slow down the process, but overall conduction dominates. In the second section, we consider a more physically realistic boundary condition, where the phase change occurs due to a heat flux from surrounding material. This removes the singularity in initial melt velocity predicted in previous models of nanoparticle melting. It is shown that even with the highest possible flux the melting time is significantly slower than with a fixed boundary temperature condition.

The melting and solidification of nanowires

Energy Technology Data Exchange (ETDEWEB)

Florio, B. J., E-mail: brendan.florio@ul.ie [University of Limerick, Mathematics Applications Consortium for Science and Industry (MACSI), Department of Mathematics and Statistics (Ireland); Myers, T. G., E-mail: tmyers@crm.cat [Centre de Recerca Matemàtica (Spain)

2016-06-15

A mathematical model is developed to describe the melting of nanowires. The first section of the paper deals with a standard theoretical situation, where the wire melts due to a fixed boundary temperature. This analysis allows us to compare with existing results for the phase change of nanospheres. The equivalent solidification problem is also examined. This shows that solidification is a faster process than melting; this is because the energy transfer occurs primarily through the solid rather than the liquid which is a poorer conductor of heat. This effect competes with the energy required to create new solid surface which acts to slow down the process, but overall conduction dominates. In the second section, we consider a more physically realistic boundary condition, where the phase change occurs due to a heat flux from surrounding material. This removes the singularity in initial melt velocity predicted in previous models of nanoparticle melting. It is shown that even with the highest possible flux the melting time is significantly slower than with a fixed boundary temperature condition.

Methods for Melting Temperature Calculation

Science.gov (United States)

Hong, Qi-Jun

Melting temperature calculation has important applications in the theoretical study of phase diagrams and computational materials screenings. In this thesis, we present two new methods, i.e., the improved Widom's particle insertion method and the small-cell coexistence method, which we developed in order to capture melting temperatures both accurately and quickly. We propose a scheme that drastically improves the efficiency of Widom's particle insertion method by efficiently sampling cavities while calculating the integrals providing the chemical potentials of a physical system. This idea enables us to calculate chemical potentials of liquids directly from first-principles without the help of any reference system, which is necessary in the commonly used thermodynamic integration method. As an example, we apply our scheme, combined with the density functional formalism, to the calculation of the chemical potential of liquid copper. The calculated chemical potential is further used to locate the melting temperature. The calculated results closely agree with experiments. We propose the small-cell coexistence method based on the statistical analysis of small-size coexistence MD simulations. It eliminates the risk of a metastable superheated solid in the fast-heating method, while also significantly reducing the computer cost relative to the traditional large-scale coexistence method. Using empirical potentials, we validate the method and systematically study the finite-size effect on the calculated melting points. The method converges to the exact result in the limit of a large system size. An accuracy within 100 K in melting temperature is usually achieved when the simulation contains more than 100 atoms. DFT examples of Tantalum, high-pressure Sodium, and ionic material NaCl are shown to demonstrate the accuracy and flexibility of the method in its practical applications. The method serves as a promising approach for large-scale automated material screening in which

An IMS testbed for SIP applications

DEFF Research Database (Denmark)

Caba, Cosmin Marius; Soler, José

2013-01-01

The paper presents the design and implementation of an emulation platform for the IP Multimedia Subsystem. The SIP Servlet API v1.1 has been used to implement the final system. The purpose of the emulation is to offer to IMS service developers an environment where they can integrate development...

Datengeleitetes Lernen im studienbegleitenden Deutschunterricht am Beispiel des KoGloss-Ansatzes

OpenAIRE

Dubova, Agnese; Proveja, Egita

2016-01-01

Der vorliegende Aufsatz stellt den sprachdidaktischen Ansatz KoGloss vor und beschreibt die Möglichkeiten seines Einsatzes im studienbegleitenden Deutschunterricht. Als eine der Formen des datengeleiteten Lernens ermöglicht der KoGloss-Ansatz eine forschungsorientierte und lernerzentrierte Herangehensweise, die insbesondere im akademischen Sprachunterricht gefragt ist. Eine korpusbasierte Erschließung von (Fach-)Wörtern und komplexen sprachlichen Mustern, das learning by doing, die Kooperatio...

Recent Changes in the Arctic Melt Season

Science.gov (United States)

Stroeve, Julienne; Markus, Thorsten; Meier, Walter N.; Miller, Jeff

2007-01-01

Melt-season duration, melt-onset and freeze-up dates are derived from satellite passive microwave data and analyzed from 1979 to 2005 over Arctic sea ice. Results indicate a shift towards a longer melt season, particularly north of Alaska and Siberia, corresponding to large retreats of sea ice observed in these regions. Although there is large interannual and regional variability in the length of the melt season, the Arctic is experiencing an overall lengthening of the melt season at a rate of about 2 weeks decade(sup -1). In fact, all regions in the Arctic (except for the central Arctic) have statistically significant (at the 99% level or higher) longer melt seasons by greater than 1 week decade(sup -1). The central Arctic shows a statistically significant trend (at the 98% level) of 5.4 days decade(sup -1). In 2005 the Arctic experienced its longest melt season, corresponding with the least amount of sea ice since 1979 and the warmest temperatures since the 1880s. Overall, the length of the melt season is inversely correlated with the lack of sea ice seen in September north of Alaska and Siberia, with a mean correlation of -0.8.

IMS IN SMES - REASONS, ADVANTAGES AND BARRIERS ON IMPLEMENTATION

Directory of Open Access Journals (Sweden)

Dragan Rajković

2008-09-01

Full Text Available Appearance of a number of management systems with various and sometimes divergent demands, demands for revise of optimal strategy on implementation of these standards in small and medium-sized enterprises (SMEs and the attempt on their integration into integrated management system are suggested even more. Firstly question on choice and reasons for implementation of standards is raised. Management and employees expect benefits on the implementation and they pass and minimize the implementation barriers. Basic concept on integrated management system (IMS into SMEs and analyse on reasons, advantages and barriers at IMS implementation are presented in this paper.

Reconocimiento de imágenes utilizando redes neuronales artificiales

OpenAIRE

García García, Pedro Pablo

2013-01-01

Este trabajo describe el proceso de extracción de patrones característicos de imágenes,mediante la ayuda de Redes Neuronales Artificiales. La información de la Red Neuronal junto con datos adicionales de las imágenes, serán almacenados en una base de datos y consumidos por un servicio web. Un teléfono móvil con sistema operativo Android consumirá la información almacenada en el servicio web. Posteriormente al realizar una captura de imagen con la cámara del teléfono, este procesará la imag...

On melting of boron phosphide under pressure

OpenAIRE

Solozhenko, Vladimir; Mukhanov, V. A.

2015-01-01

Melting of cubic boron phosphide, BP, has been studied at pressures to 9 GPa using synchrotron X-ray diffraction and electrical resistivity measurements. It has been found that above 2.6 GPa BP melts congruently, and the melting curve exhibits negative slope (–60 ± 7 K/GPa), which is indicative of a higher density of the melt as compared to the solid phase.

Melting Can Hinder Impact-Induced Adhesion

Science.gov (United States)

Hassani-Gangaraj, Mostafa; Veysset, David; Nelson, Keith A.; Schuh, Christopher A.

2017-10-01

Melting has long been used to join metallic materials, from welding to selective laser melting in additive manufacturing. In the same school of thought, localized melting has been generally perceived as an advantage, if not the main mechanism, for the adhesion of metallic microparticles to substrates during a supersonic impact. Here, we conduct the first in situ supersonic impact observations of individual metallic microparticles aimed at the explicit study of melting effects. Counterintuitively, we find that under at least some conditions melting is disadvantageous and hinders impact-induced adhesion. In the parameter space explored, i.e., ˜10 μ m particle size and ˜1 km /s particle velocity, we argue that the solidification time is much longer than the residence time of the particle on the substrate, so that resolidification cannot be a significant factor in adhesion.

Property Investigation of Laser Cladded, Laser Melted and Electron Beam Melted Ti-Al6-V4

Science.gov (United States)

2006-05-01

UNCLASSIFIED/UNLIMITED UNCLASSIFIED/UNLIMITED Figure 3: Examples of electron beam melted net shape parts; powder bed [3]. 1.4 Laser Cladding ...description, www.arcam.com. [4] K.-H. Hermann, S. Orban, S. Nowotny, Laser Cladding of Titanium Alloy Ti6242 to Restore Damaged Blades, Proceedings...Property Investigation of Laser Cladded , Laser Melted and Electron Beam Melted Ti-Al6-V4 Johannes Vlcek EADS Deutschland GmbH Corporate Research

Hybrid Silk Fibers Dry-Spun from Regenerated Silk Fibroin/Graphene Oxide Aqueous Solutions.

Science.gov (United States)

Zhang, Chao; Zhang, Yaopeng; Shao, Huili; Hu, Xuechao

2016-02-10

Regenerated silk fibroin (RSF)/graphene oxide (GO) hybrid silk fibers were dry-spun from a mixed dope of GO suspension and RSF aqueous solution. It was observed that the presence of GO greatly affect the viscosity of RSF solution. The RSF/GO hybrid fibers showed from FTIR result lower β-sheet content compared to that of pure RSF fibers. The result of synchrotron radiation wide-angle X-ray diffraction showed that the addition of GO confined the crystallization of silk fibroin (SF) leading to the decrease of crystallinity, smaller crystallite size, and new formation of interphase zones in the artificial silks. Synchrotron radiation small-angle X-ray scattering also proved that GO sheets in the hybrid silks and blended solutions were coated with a certain thickness of interphase zones due to the complex interaction between the two components. A low addition of GO, together with the mesophase zones formed between GO and RSF, enhanced the mechanical properties of hybrid fibers. The highest breaking stress of the hybrid fibers reached 435.5 ± 71.6 MPa, 23% improvement in comparison to that of degummed silk and 72% larger than that of pure RSF silk fiber. The hybrid RSF/GO materials with good biocompatibility and enhanced mechanical properties may have potential applications in tissue engineering, bioelectronic devices, or energy storage.

Spontane Mobilisierung und der Wandel kollektiver Formationen im Internet. Eine Fallstudie zur PEGIDA-Bewegung

Directory of Open Access Journals (Sweden)

Sang-hui Nam

2016-11-01

Full Text Available Der vorliegende Beitrag beschäftigt sich mit der Frage, wie sich eine aus spontaner Mobilisierung entstandene soziale Bewegung als kollektive Formation im Internet entwickelt. Da spontane Bewegungen in aller Regel nur über eine schwache kollektive Identität verfügen, werden sie bislang überwiegend als Übergangsphänomen betrachtet. Viele Studien beschäftigten sich eher mit den Folgen spontaner Mobilisierung, insbesondere der Frage, wie daraus eine nachhaltige Bewegung entstehen kann. Die kollektive Formation selbst ist bis dato weitgehend eine Blackbox geblieben. In der vorliegenden Studie widme ich mich folgenden zentralen Forschungsfragen: 1. Wie werden kollektive Formationen aus spontanen ProtestteilnehmerInnen dargestellt und generiert? 2. Wie ändern sich diese im Verlauf der Mobilisierung? Im Mittelpunkt der empirischen Analyse stehen Online-Kommentare, die eine zunehmend wichtige Rolle für soziale Bewegungen und spontane Mobilisierungsprozesse spielen. Am Beispiel von PEGIDA wird die Konstruktion einer kollektiven Formation über Live-Kommentare zu Live-Übertragungen von PEGIDA-Demonstrationen sowie deren Wandel in drei Phasen untersucht. Im ersten Schritt werden die soziotechnischen Grundlagen kollektiven Handelns im Internet erläutert. Der zweite Schritt befasst sich mit der methodischen Vorgehensweise. Im dritten Schritt werden ausgewählte Textpassagen von Online-Kommentaren analysiert. Anschließend wird der Wandel kollektiver Formationen nachgezeichnet. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs170138

Professionalisierung und Doping im Sport

OpenAIRE

Wüterich, Christoph

2004-01-01

Der Beitrag untersucht Zusammenhänge zwischen der zunehmenden Professionalisierung des Sports und dem Anstieg von Dopingvergehen. Er zeigt, dass im historischen Vergleich beide Phänomene nicht neu sind, dass sich die Probleme aufgrund der steigenden Bedeutung des Leistungssports aber zugespitzt haben. Ausgehend von einer juristischen und sozioökonomischen Analyse der Anreize zu Doping werden Lösungsvorschläge entwickelt. The author analyzes the interdependencies between a growing commercia...

Plasma arc melting of titanium-tantalum alloys

International Nuclear Information System (INIS)

Dunn, P.; Patterson, R.A.; Haun, R.

1994-01-01

Los Alamos has several applications for high temperature, oxidation and liquid-metal corrosion resistant materials. Further, materials property constraints are dictated by a requirement to maintain low density; e.g., less than the density of stainless steel. Liquid metal compatibility and density requirements have driven the research toward the Ti-Ta system with an upper bound of 60 wt% Ta-40 wt% Ti. Initial melting of these materials was performed in a small button arc melter with several hundred grams of material; however, ingot quantities were soon needed. But, refractory metal alloys whose constituents possess very dissimilar densities, melting temperatures and vapor pressures pose significant difficulty and require specialized melting practices. The Ti-Ta alloys fall into this category with the density of tantalum 16.5 g/cc and that of titanium 4.5 g/cc. Melting is further complicated by the high melting point of Ta(3020 C) and the relatively low boiling point of Ti(3287 C). Previous electron beam melting experience with these materials resulted, in extensive vaporization of the titanium and poor chemical homogeneity. Vacuum arc remelting(VAR) was considered as a melting candidate and discarded due to density and vapor pressure issues associated with electron beam. Plasma arc melting offered the ability to supply a cover gas to deal with vapor pressure issues as well as solidification control to help with macrosegregation in the melt and has successfully produced high quality ingots of the Ti-Ta alloys

On melting criteria for complex plasma

International Nuclear Information System (INIS)

Klumov, Boris A

2011-01-01

The present paper considers melting criteria for a plasma crystal discovered in dust plasma in 1994. Separate discussions are devoted to three-dimensional (3D) and two-dimensional (2D) systems. In the 3D case, melting criteria are derived based on the properties of local order in a system of microparticles. The order parameters are constructed from the cumulative distributions of the microparticle probability distributions as functions of various rotational invariants. The melting criteria proposed are constructed using static information on microparticle positions: a few snapshots of the system that allow for the determination of particle coordinates are enough to determine the phase state of the system. It is shown that criteria obtained in this way describe well the melting and premelting of 3D complex plasmas. In 2D systems, a system of microparticles interacting via a screened Coulomb (i.e., Debye-Hueckel or Yukawa) potential is considered as an example, using molecular dynamics simulations. A number of new order parameters characterizing the melting of 2D complex plasmas are proposed. The order parameters and melting criteria proposed for 2D and 3D complex plasmas can be applied to other systems as well. (methodological notes)

Flexible two-ply yarn supercapacitors based on carbon nanotube/stainless steel core spun yarns decorated with Co3O4 nanoparticles and MnOx composites

International Nuclear Information System (INIS)

Su, Fenghua; Lyu, Xiaoming; Liu, Cansen; Miao, Menghe

2016-01-01

Highlights: • Carbon nanotube/stainless steel core-sheath yarns as electrode for two-ply supercapacitor. • The yarns were decorated with Co 3 O 4 nanoparticles and MnO x composites. • Yarn electrodes deposited on Co 3 O 4 and MnO x have excellent specific capacitance. • The two-ply yarn supercapacitor based on MnO x has high energy density and power density. • The yarn supercapacitors are highly flexible and strong for wearable electronics. - Abstract: High performance two-ply yarn supercapacitors are fabricated by electrodeposition of transition metal oxide pseudocapacitive materials on carbon nanotube/stainless steel (CNT/SS) core spun yarns. The SS core incorporated in the carbon nanotube yarn has dramatically improved the conductivity of the substrate and the efficiency of electrodeposition of metal oxides on the electrodes. The SS core acts as current collector in the final two-ply yarn supercapacitors with significantly improved specific capacitance and up-scaled length of supercapacitors. Manganese oxide and cobalt oxide electrodeposited on as-spun CNT/SS yarn are compared for their electrochemical performance in two-ply yarn supercapacitors. Both supercapacitors displayed improvement in capacitance, energy and power densities, especially MnO x /CNT/SS yarn supercapacitor. The solid-state supercapacitor based on MnO x /CNT/SS composite yarn shows excellent electrochemical properties with a specific capacitance of 217.61 F/cm 3 at 0.02 V/s and an energy density of 4.84 mWh/cm 3 at a power density of 435.22 mW/cm 3 .

bildbild – visuelle Kompetenz im Unterricht

Directory of Open Access Journals (Sweden)

Norbert Grube

2013-05-01

Full Text Available Der vorliegende Artikel stellt das Webseiten-Projekt bildbild vor. Der Webseite liegt die Motivation zugrunde, Schülerinnen und Schüler für ein Nachdenken über globale Themen zu sensibilisieren. Ein solches Nachdenken ist immer auch eines über bildlich vermittelte Wirklichkeit. Es ist mit bildbild ein Anliegen, angesichts einer allseits konstatierten «Bilderflut» ein didaktisches Medium zu entwickeln, das einen Fundus an historischen und aktuellen Fotografien zur Verfügung stellt und diese so aufbereitet, dass sie gerade nicht hinter ihrer illustrativen Funktion verschwinden. Dadurch sollen die Bilder für ein selbständiges Lernen auf dem Weg hin zu einer visuellen Kompetenz einsetzbar gemacht werden. Der Beitrag beleuchtet die Entwicklung der Webseite vor dem Hintergrund kulturkritischer Haltungen zum Bild seit der Moderne sowie im Rahmen dessen, was seit den 1970er Jahren im pädagogischen Kontext als Visual Literacy diskutiert und gefördert wird. Dabei wird auch auf die medialen Potenziale einer Webseite für die Bildlesekompetenz von Jugendlichen eingegangen.

A plan for location calibration of IMS stations and near Kazakhstan

International Nuclear Information System (INIS)

Richards, P.G.; Kim, W.-Yo.; Khalturin, V.I.

2001-01-01

For purposes of monitoring compliance with the Comprehensive Nuclear Test-Ban Treaty, it is desirable to be able to locate seismic events routinely to within an uncertainty not greater than 1000 square km. From more than five years of experience with publication of the Reviewed Event Bulletin (REB) by the Prototype International Data Centre (PIDC), resulting in estimated locations for more than 100,000 seismic events, it is apparent that improved location accuracy is needed in order to reduce uncertainties below 1000 square km. In this paper, we outline a three-year program of applied research which commenced in March 2000 and which has the goal of achieving improved REB locations based upon data to be contributed to the International Data Centre from 30 IMS stations in Eastern Asia. Our first efforts will focus on the four IMS seismographic stations in Kazakhstan (AKT, BRV, KUR, MAK), together with IMS stations ZAL in Russia and AAK in Kyrgyzstan. Following the recommendations of two 'IMS Location Calibration Workshops' held in Oslo, Norway, in 1999 and 2000, our approach is to generate station-specific travel times for each observable seismic phase, as a function of distance and azimuth (and depth, where possible). Such travel times are obtained on the basis of (i) early studies based mainly on earthquake data (e.g. Nersesov and Rautian, 1964), (ii) Deep Seismic Sounding, and (iii) recent studies of nuclear and chemical explosions. We are also using (iv) an empirical approach in which phases are picked at IMS stations, for so-called Ground Truth events whose location is known quite accurately on the basis of additional data, obtained for example from local and regional networks. (author)

IMS Learning Design: De stand van zaken

NARCIS (Netherlands)

Tattersall, Colin; Manderveld, Jocelyn

2005-01-01

Tattersall, C. & Manderveld, J. (2004) IMS Learning Design: De stand van zaken In: Gorissen, P., Manderveld, J., Benneker, F. & Cordewener, B. Leertechnologie in de Lage Landen (pp. 31-33). Utrecht, Stichting Surf. Ook beschikbaar in dspace: http://hdl.handle.net/1820/270

[Christofer Herrmann. Kloster und Burg - die architektur des Deutschens Ordens im Pressen und Livland. In : Glaube, Macht und Pracht. GeistlicheGemeinschaften des Ostseeraums im Zeitalter der Backsteingotik] / Dennis Hortmuth

Index Scriptorium Estoniae

Hortmuth, Dennis

2011-01-01

Arvustus: Christofer Herrmann. Kloster und Burg - die Architektur des Deutschen Ordens in Preussen und Livland. In : Glaube, Macht und Pracht. GeistlicheGemeinschaften des Ostseeraums im Zeitalter der Backsteingotik (=Archäologie und Geschichte im Ostseeraum; Archaeology and History of the Baltic 6) Rahden : Verlag Marie Leidorf, 2009. S. 209-219. Saksa Ordu arhitektuurist Preisi- ja Liivimaal

Evaluation of the Indian Migration Study Physical Activity Questionnaire (IMS-PAQ): a cross-sectional study.

Science.gov (United States)

Sullivan, Ruth; Kinra, Sanjay; Ekelund, Ulf; Bharathi, A V; Vaz, Mario; Kurpad, Anura; Collier, Tim; Reddy, K Srinath; Prabhakaran, Dorairaj; Ebrahim, Shah; Kuper, Hannah

2012-02-09

Socio-cultural differences for country-specific activities are rarely addressed in physical activity questionnaires. We examined the reliability and validity of the Indian Migration Study Physical Activity Questionnaire (IMS-PAQ) in urban and rural groups in India. A sub-sample of IMS participants (n = 479) was used to examine short term (≤ 1 month [n = 158]) and long term (> 1 month [n = 321]) IMS-PAQ reliability for levels of total, sedentary, light and moderate/vigorous activity (MVPA) intensity using intraclass correlation (ICC) and kappa coefficients (k). Criterion validity (n = 157) was examined by comparing the IMS-PAQ to a uniaxial accelerometer (ACC) worn ≥ 4 days, via Spearman's rank correlations (ρ) and k, using Bland-Altman plots to check for systematic bias. Construct validity (n = 7,000) was established using linear regression, comparing IMS-PAQ against theoretical constructs associated with physical activity (PA): BMI [kg/m2], percent body fat and pulse rate. IMS-PAQ reliability ranged from ICC 0.42-0.88 and k = 0.37-0.61 (≤ 1 month) and ICC 0.26 to 0.62; kappa 0.17 to 0.45 (> 1 month). Criterion validity was ρ = 0.18-0.48; k = 0.08-0.34. Light activity was underestimated and MVPA consistently and substantially overestimated for the IMS-PAQ vs. the accelerometer. Criterion validity was moderate for total activity and MVPA. Reliability and validity were comparable for urban and rural participants but lower in women than men. Increasing time spent in total activity or MVPA, and decreasing time in sedentary activity were associated with decreasing BMI, percent body fat and pulse rate, thereby demonstrating construct validity. IMS-PAQ reliability and validity is similar to comparable self-reported instruments. It is an appropriate tool for ranking PA of individuals in India. Some refinements may be required for sedentary populations and women in India.

MIP-based enhanced mid-session macro-mobility for IMS-controlled state-full applications

DEFF Research Database (Denmark)

Renier, Thibault Julien; Fathi, Hanane; Schwefel, Hans-Peter

2007-01-01

, e.g., block unauthorized visiting users. The 3GPP IP Multimedia Subsystem (IMS) is a platform standardized towards network-independent access and session control. The current IMS specifications do not allow for any change of the user's current IP address during an ongoing session, which prevents...

Corium melt researches at VESTA test facility

Directory of Open Access Journals (Sweden)

Hwan Yeol Kim

2017-10-01

Full Text Available VESTA (Verification of Ex-vessel corium STAbilization and VESTA-S (-small test facilities were constructed at the Korea Atomic Energy Research Institute in 2010 to perform various corium melt experiments. Since then, several tests have been performed for the verification of an ex-vessel core catcher design for the EU-APR1400. Ablation tests of an impinging ZrO2 melt jet on a sacrificial material were performed to investigate the ablation characteristics. ZrO2 melt in an amount of 65–70 kg was discharged onto a sacrificial material through a well-designed nozzle, after which the ablation depths were measured. Interaction tests between the metallic melt and sacrificial material were performed to investigate the interaction kinetics of the sacrificial material. Two types of melt were used: one is a metallic corium melt with Fe 46%, U 31%, Zr 16%, and Cr 7% (maximum possible content of U and Zr for C-40, and the other is a stainless steel (SUS304 melt. Metallic melt in an amount of 1.5–2.0 kg was delivered onto the sacrificial material, and the ablation depths were measured. Penetration tube failure tests were performed for an APR1400 equipped with 61 in-core instrumentation penetration nozzles and extended tubes at the reactor lower vessel. ZrO2 melt was generated in a melting crucible and delivered down into an interaction crucible where the test specimen is installed. To evaluate the tube ejection mechanism, temperature distributions of the reactor bottom head and in-core instrumentation penetration were measured by a series of thermocouples embedded along the specimen. In addition, lower vessel failure tests for the Fukushima Daiichi nuclear power plant are being performed. As a first step, the configuration of the molten core in the plant was investigated by a melting and solidification experiment. Approximately 5 kg of a mixture, whose composition in terms of weight is UO2 60%, Zr 10%, ZrO2 15%, SUS304 14%, and B4C 1%, was melted in a

Pragmatic awareness of Suggestions: From (Im)Polite Mannerism to Attitudinal Appropriateness

OpenAIRE

Hamid Allami; Nasim Boustani

2017-01-01

The present research seeks to determine: (a) Iranian EFL learners’ application of suggestion semantic formulae ;(b) their attitude of appropriateness in terms of confidence in the employment of appropriate supportive moves; (c), their (im)polite mannerism with respect to the selected strategies; and (d) the relationship between attitude of appropriateness and mannerism of (im)politeness. An Oxford Quick placement Test (OQPT) was administered among 60 Iranian EFL learners to check their langua...

Produkteinführung im Umfeld des Niedergangs: Die Blu-ray Disk

OpenAIRE

Oestreicher, Klaus; Walton, Nigel; Newnham, M.

2014-01-01

Dieses Kapitel diskutiert die Problematik existenzieller Bedrohung durch radikale Innovationen. Virtuelle Marktangebote verändern Märkte im Home Entertainment und das Konsumverhalten grund¬legend. Zunehmend gefährden dematerialisierte Produkte, welche zu Services werden und Folge der Information Communication Tech¬nologies (ICT) sind, die Lebensfähigkeit physischer Produkte. Deren Märkte sind im Niedergang und das bedroht nicht nur die Hersteller optischer Disks (CD und DVD), sondern beeinflu...

A Feasibility Study on UO2/ZrO2 Mixture Melting using Induction Skull Melting Method

International Nuclear Information System (INIS)

Hong, S. W.; Kim, J. H.; Kim, H. D.

1998-01-01

Using ISM(Induction Skull Melting) method, which is usually used for the crystallization of refractory materials, a feasibility study on melting of the UO 2 /ZrO 2 mixture(w/o 8:2) is carried out. Frequency, one of main design parameters for ISM, is determined from electrical resistance of UO 2 /ZrO 2 mixture. Heat loss from the crucible for UO 2 /ZrO 2 20kg melting is predicted by comparison with the existing experimental data for UO , ZrO 2 , and ThO 2 . The analysis shows that melting and superheating of the UO 2 /ZrO 2 mixture using induction skull melting method is possible. To attain the superheat of 300K for 20 kg of UO 2 /ZrO 2 , 100kHz, 100 kW power input for induction coil, and 570L/min coolant flow rate are found to be required. The results of this feasibility study will be adopted for designing UO 2 /ZrO 2 furnace using actual corium material at KAERI

Features of melting of indium monohalides

Energy Technology Data Exchange (ETDEWEB)

Dmitriev, V S; Smirniv, V A [AN SSSR, Chernogolovka. Inst. Fiziki Tverdogo Tela

1980-12-01

The character of InCl, InBr and InI melting is investigated by the methods of DTA, calorimetry, conductometry and chemical analysis. Partial decomposition of monohalogenides during melting according to the reactions of disproportionation is shown. The presence of disproportionation products (In/sup 0/ and In/sup 3 +/) is manifested in the properties of solid monohalogenides, prepared by the crystallization from melt, in their photosensitivity and electroconductivity.

The coupled response to slope-dependent basal melting

Science.gov (United States)

Little, C. M.; Goldberg, D. N.; Sergienko, O. V.; Gnanadesikan, A.

2009-12-01

Ice shelf basal melting is likely to be strongly controlled by basal slope. If ice shelves steepen in response to intensified melting, it suggests instability in the coupled ice-ocean system. The dynamic response of ice shelves governs what stable morphologies are possible, and thus the influence of melting on buttressing and grounding line migration. Simulations performed using a 3-D ocean model indicate that a simple form of slope-dependent melting is robust under more complex oceanographic conditions. Here we utilize this parameterization to investigate the shape and grounding line evolution of ice shelves, using a shallow-shelf approximation-based model that includes lateral drag. The distribution of melting substantially affects the shape and aspect ratio of unbuttressed ice shelves. Slope-dependent melting thins the ice shelf near the grounding line, reducing velocities throughout the shelf. Sharp ice thickness gradients evolve at high melting rates, yet grounding lines remain static. In foredeepened, buttressed ice shelves, changes in grounding line flux allow two additional options: stable or unstable retreat. Under some conditions, slope-dependent melting results in stable configurations even at high melt rates.

Low HAP Materials

Science.gov (United States)

2009-09-01

Use maleinized triglycerides to replace UPE • Use novel bio-based reactive diluent to replace styrene Bio-Based Carbon Fibers and Thermosetting Resins...SERDP proposed new start, FY10 • Microbially breakdown lignin into oligomers that can be melt spun and carbonized • Modify renewable...D5045-93 • Designed plant oil-based toughening agents • Uses phase separation to capture MFA reactive diluent • Increases toughness while decreasing

Facebook Ethnography: The Poststructural Ontology of Transnational (Im Migration Research

Directory of Open Access Journals (Sweden)

David Joseph Piacenti PhD

2014-02-01

Full Text Available This theoretical article discusses the creative utility of Facebook as a new ethnographic tool in which to study transnational (im migration. Facebook ethnography allows the (im migration researcher to transcend the four structural dualities that constrain transnational ethnographic research: (a geographic constraints, (b travel funding constraints, (c travel time constraints, and (d the logistical constraints of entrée into new ethnographic contexts. Facebook ethnography also allows the qualitative researcher to temporarily transcend the ontological structuralist dualities of traditional research methods, producing a new poststructural epistemological and ontological methodology.

A flicker noise/IM3 cancellation technique for active mixer using negative impedance

NARCIS (Netherlands)

Cheng, W.; Annema, Anne J.; Wienk, Gerhardus J.M.; Nauta, Bram

2013-01-01

Abstract—This paper presents an approach to simultaneously cancel flicker noise and IM3 in Gilbert-type mixers, utilizing negative impedances. For proof of concept, two prototype double-balanced mixers in 0.16- m CMOS are fabricated. The first demonstration mixer chip was optimized for full IM3

Network topology of olivine-basalt partial melts

Science.gov (United States)

Skemer, Philip; Chaney, Molly M.; Emmerich, Adrienne L.; Miller, Kevin J.; Zhu, Wen-lu

2017-07-01

The microstructural relationship between melt and solid grains in partially molten rocks influences many physical properties, including permeability, rheology, electrical conductivity and seismic wave speeds. In this study, the connectivity of melt networks in the olivine-basalt system is explored using a systematic survey of 3-D X-ray microtomographic data. Experimentally synthesized samples with 2 and 5 vol.% melt are analysed as a series of melt tubules intersecting at nodes. Each node is characterized by a coordination number (CN), which is the number of melt tubules that intersect at that location. Statistically representative volumes are described by coordination number distributions (CND). Polyhedral grains can be packed in many configurations yielding different CNDs, however widely accepted theory predicts that systems with small dihedral angles, such as olivine-basalt, should exhibit a predominant CN of four. In this study, melt objects are identified with CN = 2-8, however more than 50 per cent are CN = 4, providing experimental verification of this theoretical prediction. A conceptual model that considers the role of heterogeneity in local grain size and melt fraction is proposed to explain the formation of nodes with CN ≠ 4. Correctly identifying the melt network topology is essential to understanding the relationship between permeability and porosity, and hence the transport properties of partial molten mantle rocks.

Melt Fragmentation Characteristics of Metal Fuel with Melt Injection Mass during Initiating Phase of SFR Severe Accidents

Energy Technology Data Exchange (ETDEWEB)

Heo, Hyo; Lee, Min Ho; Bang, In Cheol [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of); Jerng, Dong Wook [Chung-Ang Univ., Seoul (Korea, Republic of)

2016-05-15

The PGSFR has adopted the metal fuel for its inherent safety under severe accident conditions. However, this fuel type is not demonstrated clearly yet under the such severe accident conditions. Additional experiments for examining these issues should be performed to support its licensing activities. Under initiating phase of hypothetic core disruptive accident (HCDA) conditions, the molten metal could be better dispersed and fragmented into the coolant channel than in the case of using oxide fuel. This safety strategy provides negative reactivity driven by a good dispersion of melt. If the coolant channel does not sufficient coolability, the severe recriticality would occur within the core region. Thus, it is important to examine the extent of melt fragmentation. The fragmentation behaviors of melt are closely related to a formation of debris shape. Once the debris shape is formed through the fragmentation process, its coolability is determined by the porosity or thermal conductivity of the melt. There were very limited studies for transient irradiation experiments of the metal fuel. These studies were performed by Transient Reactor Test Facility (TREAT) M series tests in U.S. The TREAT M series tests provided basic information of metal fuel performance under transient conditions. The effect of melt injection mass was evaluated in terms of the fragmentation behaviors of melt. These behaviors seemed to be similar between single-pin and multi-pins failure condition. However, the more melt was agglomerated in case of multi-pins failure.

78 FR 79498 - Notice Pursuant to The National Cooperative Research and Production Act of 1993-IMS Global...

Science.gov (United States)

2013-12-30

... Production Act of 1993--IMS Global Learning Consortium, Inc. Notice is hereby given that, on November 22....C. Sec. 4301 et seq. (``the Act''), IMS Global Learning Consortium, Inc. (``IMS Global'') has filed..., Carson-Dellosa Publishing, Greensboro, NC; Data Recognition Group, Maple Grove, MN; Nelson Education Ltd...

78 FR 7456 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-IMS Global...

Science.gov (United States)

2013-02-01

... District, Selbyville, DE; learning.com , Portland, OR; State of Michigan Dept. of Education, Bureau of... Production Act of 1993--IMS Global Learning Consortium, Inc. Notice is hereby given that, on December 28....C. 4301 et seq. (``the Act''), IMS Global Learning Consortium, Inc. (``IMS Global'') has filed...

Electron beam melting of bearing materials

Energy Technology Data Exchange (ETDEWEB)

Goldschmied, G.; Schuler, A. (Technische Univ., Vienna (Austria). Inst. fuer Allgemeine Elektrotechnik); Elsinger, G.; Koroschetz, F. (MIBA Gleitlager AG, Laakirchen (Austria)); Tschegg, E.K. (Technische Univ., Vienna (Austria). Inst. fuer Angewandte und Technische Physik)

1990-06-01

This paper reports on a surface treatment method for the bearing materials AlSn6 which permits the use of this material without the overlay usually required. Microstructural refinement is achieved by means of a surface melting technique using an electron beam with successive rapid solidification. Extremely fine tin precipitates are formed in the melted surface layer which lead to significantly better tribological properties of the bearing material. Tests compared the tribological properties for AlSn6 bearings treated by the surface melting technique with those of untreated bearings. Whereas all untreated bearings failed by seizure after only 2 h of testing, 30% of the tested bearings which had been surface melted survived the entire testing program without damage.

Evaluation of the i-STAT point-of-care capillary whole blood hematocrit and hemoglobin: Comparison to the Siemens RAPIDLab 1200, Sysmex XE5000, and manual spun hematocrit.

Science.gov (United States)

Rudolf, Joseph; Douglass, Joseph; Baron, Jason; Lewandrowski, Kent

2015-06-15

Conductivity based point-of-care hematocrit with calculated hemoglobin devices serves an important role in clinical scenarios where time sensitive transfusion decisions are necessary. However, questions about the appropriateness of conductivity based assays in certain patient populations (patients on cardiopulmonary bypass and those receiving high volumes of intravenous fluids or autologous blood transfusions) have been raised. The clinical suitability of POC devices for these applications necessitates that they be accurate and that the results are interchangeable with central laboratory methods. We performed hematocrit and hemoglobin analysis on 225 clinical samples using the i-STAT instrument, a standard reference method for hematocrit (manual spun) and other common methods on both cardiopulmonary bypass and non-cardiopulmonary bypass patients. The i-STAT hematocrit and hemoglobin showed close agreement to comparison methods with minimal bias. Median test results were not clinically or statistically different between those measured on the i-STAT and those measured using the manual spun hematocrit reference method (p=0.4085, Wilcoxon signed rank test) or the Sysmex photometric hemoglobin method (p=0.2728, Wilcoxon signed rank test). The results on the i-STAT were statistically different from those obtained on the Sysmex for hematocrit (phemoglobin (phematocrit and hemoglobin performs well when compared to the hematocrit reference method and other common methods for both hematocrit and hemoglobin. Some differences between non-reference methods may be observed, but these were not considered clinically significant. Copyright © 2015 Elsevier B.V. All rights reserved.

SISTEMAS MULTIMEDIA BASADOS EN PROTOCOLO IP IMS APLICADOS A SERVICIOS LTE DE 4G

Directory of Open Access Journals (Sweden)

Edgar Alfonso Cipagauta Pedraza

2013-01-01

Full Text Available Este artículo presenta de una manera sencilla, el sistema creado para soportar los servicios de multimedia dentro de red de nueva generación (NGN llamada IP Multimedia Subsystem (IMS a la vez que se explica su relación con la tecnología Long Term Evolution (LTE definida por el 3GPP en su release 8. IMS se trata de una arquitectura integrada en el núcleo de red para ofrecer servicios multimediales de audio y video sobre una infraestructura. Entonces ahora, los servicios prestados pasarán a ser ofrecidos a través de IP IMS y será la piedra angular en donde estos servicios se generarán y se ofrecerán. LTE es sin duda un impulsor de IMS, pero hay otros factores que empiezan a favorecer y a plantear un modelo de negocio favorable para la arquitectura multimedia. IMS está orientado a habilitar la convergencia de servicios, combinando el crecimiento de la Internet con el de las comunicaciones móviles, desde cualquier ubicación y método de forma continua y permanente.

EXTREMISMUS IM KLASSENZIMMER - THEORETISCHE CHANCEN UND MÖGLICHKEITEN DES POLITIKUNTERRICHTES.

Directory of Open Access Journals (Sweden)

Amelie Zuschke

2015-06-01

Full Text Available Durch Phänomene wie PEGIDA wird eine Unsicherheit in der Bevölkerung ausgedrückt, die auch vor den Schultüren nicht Halt macht. Ein Querschnitt der Gesellschaft sitzt im Klassenraum und auf diesen muss sich eingestellt werden. Ob Kinder zuhause oder in ihrer Freizeit mit Populismus konfrontiert werden, die Schule hat als immer größerer Teil im Leben von Schülern in Deutschland (im Zuge der nach und nach fortschreitenden Einführung eines Ganztages-Prinzips auch eine Verantwortung mit diesen Eindrücken und Einflüssen bedacht umzugehen. Deutschland sollte aus der eigenen Geschichte heraus zudem die aufmerksame und sensible Handhabung mit extremem Gedankengut im Allgemeinen und mit rechtsextremistischem Gedankengut im Besonderen haben. Die Tendenz zu den politischen Extremen in wirtschaftlich und sozial herausfordernden Zeiten ist ein mit jedem wirtschaftlichen Abschwung auftretendes Phänomen, aber stark nationalistisches Gedankengut ist mit der heutigen Idealvorstellung von einem offenen Europa nicht vereinbar. In der Bundesrepublik Deutschland fußt die politische Bildung, geschichtlich begründet, auf demokratievermittelnden Prinzipien. Diese eignen sich vielseitig für die Auseinandersetzung mit Extremismus und den hierzu unumstrittenen Grundlagen und Werte der pluralistischen Gesellschaft in einer Demokratie. Das Kontroversitätsgebot des Beutelsbacher Konsenses aus dem Jahr 1977 (vgl Breit/Massig, 1993 bietet einen Ansatz zur Behandlung von Extremismus in der politischen Bildung auf der Grundlage der gegenseitigen Akzeptanz. Hier wird das Kontroversitätsgebot aufgeschlüsselt und anschließend auf Extremismus in der Schule bezogen. Die Fragestellung, wie der Politikunterricht trotz des Kontroversitätsgebotes mit Extremismus umgehen sollte, ist auf den Umgang mit dem gegenwärtigen Rechtsextremismus ausgelegt, welcher einen großen Teil politisch motivierter Straftaten begründet, sich in radikalisierter Form am stärksten gegen

Entwicklung der Reglementierung von 10 MEM-Berufen im Kontext von Bildungsreformen und dem Wandel in der Arbeitswelt: Eine Kurzstudie im Auftrag von LIBS: Eine Kurzstudie im Auftrag von LIBS Industrielle Berufslehren Schweiz, Baden

OpenAIRE

Egg, Maria Esther; Renold, Ursula

2015-01-01

Im Auftrag der LIBS Industrielle Berufslehren Schweiz, hat die KOF die Entwicklung von 10 MEM1-Berufsbildern seit dem ersten Berufsbildungsgesetz dargestellt und diese eingebettet in eine kurze Zusammenfassung der wichtigsten Etappenschritte des Schweizer Berufsbildungssystems.

Nitrogen Control in VIM Melts

Science.gov (United States)

Jablonski, P. D.; Hawk, J. A.

NETL has developed a design and control philosophy for the addition of nitrogen to austenitic and ferritic steels. The design approach uses CALPHAD as the centerpiece to predict the level to which nitrogen is soluble in both the melt and the solid. Applications of this technique have revealed regions of "exclusion" in which the alloy, while within specification limits of prescribed, cannot be made by conventional melt processing. Furthermore, other investigations have found that substantial retrograde solubility of nitrogen exists, which can become problematic during subsequent melt processing and/or other finishing operations such as welding. Additionally, the CALPHAD method has been used to adjust primary melt conditions. To that end, nitrogen additions have been made using chrome nitride, silicon nitride, high-nitrogen ferrochrome as well as nitrogen gas. The advantages and disadvantages of each approach will be discussed and NETL experience in this area will be summarized with respect to steel structure.

Additive Manufacturing Processes: Selective Laser Melting, Electron Beam Melting and Binder Jetting-Selection Guidelines.

Science.gov (United States)

Gokuldoss, Prashanth Konda; Kolla, Sri; Eckert, Jürgen

2017-06-19

Additive manufacturing (AM), also known as 3D printing or rapid prototyping, is gaining increasing attention due to its ability to produce parts with added functionality and increased complexities in geometrical design, on top of the fact that it is theoretically possible to produce any shape without limitations. However, most of the research on additive manufacturing techniques are focused on the development of materials/process parameters/products design with different additive manufacturing processes such as selective laser melting, electron beam melting, or binder jetting. However, we do not have any guidelines that discuss the selection of the most suitable additive manufacturing process, depending on the material to be processed, the complexity of the parts to be produced, or the design considerations. Considering the very fact that no reports deal with this process selection, the present manuscript aims to discuss the different selection criteria that are to be considered, in order to select the best AM process (binder jetting/selective laser melting/electron beam melting) for fabricating a specific component with a defined set of material properties.

Additive Manufacturing Processes: Selective Laser Melting, Electron Beam Melting and Binder Jetting—Selection Guidelines

Science.gov (United States)

Konda Gokuldoss, Prashanth; Kolla, Sri; Eckert, Jürgen

2017-01-01

Additive manufacturing (AM), also known as 3D printing or rapid prototyping, is gaining increasing attention due to its ability to produce parts with added functionality and increased complexities in geometrical design, on top of the fact that it is theoretically possible to produce any shape without limitations. However, most of the research on additive manufacturing techniques are focused on the development of materials/process parameters/products design with different additive manufacturing processes such as selective laser melting, electron beam melting, or binder jetting. However, we do not have any guidelines that discuss the selection of the most suitable additive manufacturing process, depending on the material to be processed, the complexity of the parts to be produced, or the design considerations. Considering the very fact that no reports deal with this process selection, the present manuscript aims to discuss the different selection criteria that are to be considered, in order to select the best AM process (binder jetting/selective laser melting/electron beam melting) for fabricating a specific component with a defined set of material properties. PMID:28773031

Modeling the summertime evolution of sea-ice melt ponds

DEFF Research Database (Denmark)

Lüthje, Mikael; Feltham, D.L.; Taylor, P.D.

2006-01-01

We present a mathematical model describing the summer melting of sea ice. We simulate the evolution of melt ponds and determine area coverage and total surface ablation. The model predictions are tested for sensitivity to the melt rate of unponded ice, enhanced melt rate beneath the melt ponds...

The Laser Damage Threshold for Materials and the Relation Between Solid-Melt and Melt-Vapor Interface Velocities

International Nuclear Information System (INIS)

Khalil, Osama Mostafa

2010-01-01

Numerous experiments have demonstrated and analytic theories have predicted that there is a threshold for pulsed laser ablation of a wide range of materials. Optical surface damage threshold is a very complex and important application of high-power lasers. Optical damage may also be considered to be the initial phase of laser ablation. In this work it was determined the time required and the threshold energy of a layer of thickness to heat up. We used the Finite Difference method to simulate the process of laser-target interaction in three cases. Namely, the case before melting begins using a continuous wave (c.w) laser source and a pulsed laser source, the case after the first change of state (from solid to melt), and the case after the second change of state (from melt to vapor). And also study the relation between the solid-melt and melt-vapor interface velocities to have a commonsense of the laser ablation process.

Melt-processing method for radioactive solid wastes

International Nuclear Information System (INIS)

Kobayashi, Hiroaki

1998-01-01

Radioactive solid wastes are charged into a water-cooled type cold crucible induction melting furnace disposed in high frequency coils, and high frequency currents are supplied to high frequency coils which surround the melting furnace to melt the solid wastes by induction-heating. In this case, heat plasmas are jetted from above the solid wastes to the solid wastes to conduct initial heating to melt a portion of the solid wastes. Then, high frequency currents are supplied to the high frequency coils to conduct induction heating. According to this method, even when waste components of various kinds of materials are mixed, a portion of the solid wastes in the induction melting furnace can be melted by the initial heating by jetting heat plasmas irrespective of the kinds and the electroconductivity of the materials of the solid wastes. With such procedures, entire solid wastes in the furnace can be formed into a molten state uniformly and rapidly. (T.M.)

IMS Learning Design desde dentro. Una especificación para crear escenarios de aprendizaje online (parte I)

NARCIS (Netherlands)

Burgos, Daniel; Berbegal, Nidia; Griffiths, David; Tattersall, Colin; Koper, Rob

2005-01-01

IMS Learning Design, IMS LD de ahora en adelante (IMS, 2003), es una especificación centrada en formación online o e-learning y que permite modelar programaciones curriculares o lecciones presenciales de forma que puedan ser seguidas online, construyendo lo que se denomina Unidades de Aprendizaje

Aplicativo Web para la Fusión de Imágenes Satelitales

Directory of Open Access Journals (Sweden)

Javier Medina

2013-06-01

Full Text Available En este artículo se implementa un servicio en la Web que ofrece la posibilidad de realizar la fusión de imágenes de satélite. A lo largo del artículo tres temáticas importantes son abordadas. La primera temática corresponde al servicio Web, éste servicio es implementado usando software libre, donde el usuario puede realizar una solicitud del servicio de fusión. La segunda temática se ocupa del análisis de la transformada rápida de Wavelet haar (TRWH. La última temática detalla la metodología, para realizar la fusión de imágenes usando la TRWH. Con el fin de determinar la eficiencia de la TRWH, cinco Wavelets diferentes fueron implementadas para fusionar el mismo par de imágenes satelitales. Las imágenes resultantes fueron evaluadas tanto en la calidad espacial como espectral a través de cuatro índices. Los mejores resultados de la evaluación fueron obtenidos con la TRWH la cual preserva la riqueza espectral y mejora su calidad espacial

Original models of NGN/IMS-networks surrounded by circuit-switched systems

OpenAIRE

Kulikov, Nikolay

2014-01-01

On obtaining of the Alexander Graham Bell a patent for invention of the telephone in 1987, the communication system consistently has gone through several evolutionary stages: from analog lines and manual switches to video telephony and IMS architecture. Each of the stages can be described by specific switching systems, data transmission systems and types of transmitted information. After implementation of such solution, it is possible to create a number of access nodes in the Operators IMS-ne...

Phase formation and crystallization behavior of melt spun Sm-Fe-based alloys

International Nuclear Information System (INIS)

Shield, J.E.

1999-01-01

The phase formation and microstructures of Sm-Fe alloys have been investigated at Sm levels of 11 and 17 atomic percent and with alloying additions of Ti and C. At lower Sm content, virtually phase pure SmFe 7 formed, while higher Sm content resulted in the formation of SmFe 7 , SmFe 2 and amorphous phases. The addition of Ti and C resulted in greater stability and a larger volume fraction of the amorphous phase. The binary Sm-Fe alloys at both Sm levels had tremendously variable microstructures, with large discrepancies in grain size and phase distribution from region to region. The addition of Ti and C tended to result in a more homogeneous microstructure, as well as a refinement in the microstructural scale. (orig.)

Realization of Copper Melting Point for Thermocouple Calibrations

Directory of Open Access Journals (Sweden)

Y. A. ABDELAZIZ

2011-08-01

Full Text Available Although the temperature stability and uncertainty of the freezing plateau is better than that of the melting plateau in most of the thermometry fixed points, but realization of melting plateaus are easier than that of freezing plateaus for metal fixed points. It will be convenient if the melting points can be used instead of the freezing points in calibration of standard noble metal thermocouples because of easier realization and longer plateau duration of melting plateaus. In this work a comparison between the melting and freezing points of copper (Cu was carried out using standard noble metal thermocouples. Platinum - platinum 10 % rhodium (type S, platinum – 30 % rhodium / platinum 6 % rhodium (type B and platinum - palladium (Pt/Pd thermocouples are used in this study. Uncertainty budget analysis of the melting points and freezing points is presented. The experimental results show that it is possible to replace the freezing point with the melting point of copper cell in the calibration of standard noble metal thermocouples in secondary-level laboratories if the optimal methods of realization of melting points are used.

Partial enthalpies of Bi and Te in Bi-Te melts and of In and Te in In-Te melts

International Nuclear Information System (INIS)

Yassin, Abeer; Amzil, Abdelhamid; Castanet, Robert

2000-01-01

Full text.Calorimetric measurement are reported which allow the enthalpic behaviour of Bi-Te melts to be established. Further work is required, however, to supplement results obtained for In-Te melts. The partial enthalpies of bismuth and tellurium in the Bi-Te melts at 755K and those of indium and tellurium in the In-Te melts at 1010 and 987K were measured at high dilution by direct reaction calorimetry (drop method) with the help of a Tian-Calvet calorimeter. The limiting partial enthalpies of the components were deduced by extrapolation at infinite dilution: Δh f,∞ B i(755K)/KJ.mol -1 = -34.0 and Δh f,∞ Te(755K) /KJ·mol -1 = -24.1 in the Bi-Te melts Δh f,∞ In(1010K) /KJ·mol -1 = -75.9 and Δh f,∞ Te(1010K) /KJ·mol -1 = -47.8 in the In-Te melts Δh f,∞ In(987K) /KJ·mol -1 = -75.2 and Δh f,∞ Te(987K) /KJ·mol -1 = -48.0 in the In-Te melts

An IMS Station life cycle from a sustainment point of view

Science.gov (United States)

Brely, Natalie; Gautier, Jean-Pierre; Foster, Daniel

2014-05-01

The International Monitoring System (IMS) is to consist of 321 monitoring facilities, composed of four different technologies with a variety of designs and equipment types, deployed in a range of environments around the globe. The International Monitoring System is conceived to operate in perpetuity through maintenance, replacement and recapitalization of IMS facilities' infrastructure and equipment when the end of service life is reached [CTBT/PTS/INF.1163]. Life Cycle techniques and modellization are being used by the PTS to plan and forecast life cycle sustainment requirements of IMS facilities. Through historical data analysis, Engineering inputs and Feedback from experienced Station Operators, the PTS currently works towards increasing the level of confidence on these forecasts and sustainment requirements planning. Continued validation, feedback and improvement of source data from scientific community and experienced users is sought and essential in order to ensure limited effect on data availability and optimal costs (human and financial).

International Monitoring system (IMS) build-up in Africa: Current status and the way forward

International Nuclear Information System (INIS)

Basham, P.

2002-01-01

The complete IMS verification system for primary and auxiliary seismic together with that of radionuclide, hydroacoustic and infrasound is plotted on a global map and Africa in particular showing its status. IMS situation in East and Southern Africa is included

Online interferometric study of viscoelastic rupture and necking deformation of as-spun (iPP) fibres due to creep process.

Science.gov (United States)

Sokkar, Taha; El-Farahaty, Kermal; Azzam, Amira

2015-01-01

Creep deformation under constant load leads to rupture when the polymer chains can no longer separate and accommodate the load. This fracture phenomenon is investigated interferometrically. The creep behaviour of as-spun isotactic Polypropylene (iPP) fibres is studied at different stresses, different initial lengths and different radii. The creep rate, which defines the velocity of the creep deformation and the dimensional stability of the material, is studied. The failure time and stress of iPP due to creep process is determined. The necking deformation was in situ detected during creep process. The mean refractive indices (n(P) andn⊥) profiles of iPP fibres were determined at different positions along the fibre axis before and after necking. The relation between the creep behaviour and different optical and structural parameters is investigated. Microinterferograms are given for illustration. © 2015 The Authors Journal of Microscopy © 2015 Royal Microscopical Society.

Implementing Adaptive Educational Methods with IMS Learning Design

NARCIS (Netherlands)

Specht, Marcus; Burgos, Daniel

2006-01-01

Please, cite this publication as: Specht, M. & Burgos, D. (2006). Implementing Adaptive Educational Methods with IMS Learning Design. Proceedings of Adaptive Hypermedia. June, Dublin, Ireland. Retrieved June 30th, 2006, from http://dspace.learningnetworks.org

Ferric iron partitioning between pyroxene and melt during partial melting of the Earth's upper mantle

Science.gov (United States)

Rudra, A.; Hirschmann, M. M.

2017-12-01

The oxidation state of the Earth's mantle influences melt production, volatile behavior, partitioning of key trace elements and possible saturation of alloy at depth. Average Fe3+/FeT ratios in MORBs indicate oxygen fugacitiy of the source regions is close to QFM, in contrast to a 3 log unit variation of fO2 recorded by abyssal peridotites. Quantification of the relationship between basalt and source Fe3+/FeT, oxygen fugacity, and melting requires constraints on Fe3+ partitioning between melt and mantle minerals and in particular the principal Fe3+ host, pyroxene. McCanta et al. (2004) investigated valence dependent partitioning of Fe between Martian ferroan pigeonites and melt, but behavior in terrestrial pyroxene compositions relevant to MORB petrogenesis has not been investigated. We are conducting 1 atm controlled fO2 experiments over 4 log unit variation of fO2 between ΔQFM = 2.5 to -1.5 to grow pyroxenes of variable tetrahedral and octahedral cationic population from andesitic melts of varying Mg#, alumina and alkali content. Dynamic crystallization technique facilitates growth of pyroxene crystals (100-200 um) that EPMA analyses show to be compositionally homogeneous and in equilibrium with the melt. Fe3+/FeT ratio of the synthetic pyroxenes have been analyzed by XAFS spectroscopy at the APS (GSECARS) synchrotron. To quantify the x-ray anisotropy in pyroxenes, we collected Fe K-edge XAFS spectra of oriented natural single crystals for a wide range compositions whose Fe3+/FeT ratios we determined by Mossbauer spectroscopy. We have collected both XANES and EXAFS spectral regions spanning from 7020-7220 eV to explore predictive capabilities of different spectral regions about ferric iron concentration and site occupancy. Our results will document the Fe3+ compatibility in pyroxenes of different compositions under a variety of fO2 conditions, which in turn will better constrain the interrelationship between mantle redox and melting.

Plasma arc melting of zirconium

International Nuclear Information System (INIS)

Tubesing, P.K.; Korzekwa, D.R.; Dunn, P.S.

1997-01-01

Zirconium, like some other refractory metals, has an undesirable sensitivity to interstitials such as oxygen. Traditionally, zirconium is processed by electron beam melting to maintain minimum interstitial contamination. Electron beam melted zirconium, however, does not respond positively to mechanical processing due to its large grain size. The authors undertook a study to determine if plasma arc melting (PAM) technology could be utilized to maintain low interstitial concentrations and improve the response of zirconium to subsequent mechanical processing. The PAM process enabled them to control and maintain low interstitial levels of oxygen and carbon, produce a more favorable grain structure, and with supplementary off-gassing, improve the response to mechanical forming

Multimedia als Entwicklungsfaktor im ländlichen Raum? : Fallbeispiel Wirtschaftsregion Friedrichshafen/Bodensee

OpenAIRE

Haupenthal, Edmund; Leuninger, Stefan; Beermann, Petra; Kutter, Martina

1998-01-01

Im Rahmen der vorliegenden empirischen Studie in der Wirtschaftsregion Friedrichshafen wurden die Wechselwirkungen zwischen regionalen Strukturfaktoren und „Multimedia-Entwicklungen“ im ländlichen Raum untersucht. Die positive Multimedia-Entwicklung geht auf folgende regionale Erfolgsfaktoren zurück: die politische Akzeptanz der neuen Technologie, die Vorhaltung der Multimedia-Akademie, die regionale Nachfrage, die Verfügbarkeit ausreichenden Know-hows und Humankapitals sowie das Vorhandensei...

Effects of surface shape on the geometry and surface topography of the melt pool in low-power density laser melting

KAUST Repository

Kim, Youngdeuk; Kim, Wooseung

2011-01-01

The quantitative correlations between workpiece volume and melt pool geometry, as well as the flow and thermal features of the melt pool are established. Thermocapillary convections in melt pool with a deformable free surface are investigated

Emotionsregulationsstrategien und aggressives Verhalten im Kindergartenalter

OpenAIRE

Helmsen, Johanna; Petermann, Franz

2010-01-01

In der vorliegenden Studie (N = 193) wurde untersucht, ob sich körperlich und relational aggressive Kinder im Kindergartenalter (mittleres Alter: 55 Monate) in ihren Emotionsregulationsstrategien von ihren unauffälligen Altersgenossen unterscheiden. Zur Erhebung der Emotionsregulation wurde eine strukturierte, videografierte Verhaltensbeobachtung durchgeführt, in der gezielt Frustration ausgelöst wurde. Anschließend wurden Regulationsstrategien in sieben verschiedenen Kategorien ausgewertet. ...

MELTS_Excel: A Microsoft Excel-based MELTS interface for research and teaching of magma properties and evolution

Science.gov (United States)

Gualda, Guilherme A. R.; Ghiorso, Mark S.

2015-01-01

thermodynamic modeling software MELTS is a powerful tool for investigating crystallization and melting in natural magmatic systems. Rhyolite-MELTS is a recalibration of MELTS that better captures the evolution of silicic magmas in the upper crust. The current interface of rhyolite-MELTS, while flexible, can be somewhat cumbersome for the novice. We present a new interface that uses web services consumed by a VBA backend in Microsoft Excel©. The interface is contained within a macro-enabled workbook, where the user can insert the model input information and initiate computations that are executed on a central server at OFM Research. Results of simple calculations are shown immediately within the interface itself. It is also possible to combine a sequence of calculations into an evolutionary path; the user can input starting and ending temperatures and pressures, temperature and pressure steps, and the prevailing oxidation conditions. The program shows partial updates at every step of the computations; at the conclusion of the calculations, a series of data sheets and diagrams are created in a separate workbook, which can be saved independently of the interface. Additionally, the user can specify a grid of temperatures and pressures and calculate a phase diagram showing the conditions at which different phases are present. The interface can be used to apply the rhyolite-MELTS geobarometer. We demonstrate applications of the interface using an example early-erupted Bishop Tuff composition. The interface is simple to use and flexible, but it requires an internet connection. The interface is distributed for free from http://melts.ofm-research.org.

Melting technique for vanadium containing steels

Energy Technology Data Exchange (ETDEWEB)

Grishanov, M P; Gutovskij, I B; Vakhrushev, A S

1980-04-28

To descrease cost price of high-quality vanadium steels a method of their melting in open-hearth furnaces with acid lining using slag-metal fraction of vanadium, which is loaded in the content of 2.1-4.7% of melting mass, is suggested. Introduction of slag-metal fraction of vanadium ensures the formation of slag with composition that guarantees the necessary content of vanadium in steel and does not require introduction of expensive vanadium-containing ferroalloys into the melt.

STUDI KUALITATIF MENGENAI PERSEPSI DAN PERILAKU SEKSUAL WANITA PEKERJA SEKS KOMERSIAL (PSK DALAM UPAYA PENCEGAHAN IMS DI KOTA SEMARANG TAHUN 2012

Directory of Open Access Journals (Sweden)

Ratu Matahari

2015-04-01

Full Text Available Pendahuluan: Peningkatan jumlah kasus IMS di Kota Semarangdengan jumlah kasus IMS pada tahun 2009 tercatat mencapai 2.471 kasusdan jumlah kasus IMS pada tahun 2011 adalah 2473 kasus. Tujuan: Mendeskripsikan persepsi dan perilaku seksual wanita Pekerja Seks Komersial (PSK di Lokalisasi Sunan Kuning terhadap upaya pencegahan Infeksi Menular Seksual (IMS di Kota Semarang. Metode: Penelitian ini dilakukan dengan menggunakan teknik wawancara mendalam (indepth interview pada enam PSK yang mengalami IMS dan mewawancarai dua kelompok diskusi (FGD, seorang mucikari, dan seorang petugas lapangan (PL sebagai triangulasi. Analisis data menggunakan analisis isi (content analysis. Hasil: Pola Pengetahuan PSK dan persepsi PSK terhadap IMS juga sudah baik, tetapi perilaku PSK dalam upaya mencegah penularan IMS masih belum bisa dikatakan baik karena penggunaan kondom diantara pekerja seks komersial pada saat melakukan hubungan seksual dengan pelanggannya masih rendah. Tidak adanya dukungan dari mucikari dalam meningkatkan perilaku pencegahan IMS. Hal ini menunjukkan bahwa kepedulian terhadap kesehatan diri sendiri masih rendah. Kesimpulan: Perilaku pencegahan PSK terhadap penularan IMS belum baik. Perlu diadakan pelatihan dengan metode role playing kepada para PSK dan mucikari untuk meningkatkan kepedulian mereka terhadap kesehatan sehingga diharapkan akan terjadi perubahan perilaku baru dalam upaya pencegahan penularan IMS terhadap diri mereka sendiri atau pelanggan.  Kata kunci: Persepsi, pekerja seks komersial, IMS, Kota Semarang

Suchverhalten im Web: Empirische Ergebnisse

OpenAIRE

Schmidt-Mänz, Nadine

2005-01-01

Nadine Schmidt-Mänz vom Institut für Entscheidungstheorie u. Unternehmensforschung, Universität Karlsruhe, berichtete über „Suchverhalten im Web: Empirische Ergebnisse“. Rund 6000 Benutzer von Suchmaschinen füllten den von ihr hergestellten Online-Fragebogen aus. Einige ihrer Erkenntnisse: Als Suchmaschine wurde mit 91,3 % Google benutzt. Die Monopolstellung von Google war den Suchenden nicht bewußt. Einer der Schlüsse der Referentin: Es mangelt nicht an Suchmaschinen, sondern an der „Weitere...

Artroscopia del hombro: Técnica e imágenes

OpenAIRE

ARANGO GARCIA, GASTON; ALVAREZ CAMBRAS, RODRIGO; LOPEZ CABRERA, JOSE RAMON; MIRANDEZ OLARAN, HUGO; LARA VALDIVIA, JESUS

1995-01-01

En este trabajo se muestra cómo realizar la técnica de la artroscopia de la articulación del hombro. Se presentan vistas de las imágenes artroscópicas y de la anatomía normal de la articulación para ayudar a la interpretación e identificación de las imágenes patológicas más comúnmente encontradas. Se realizó la técnica en 8 pacientes, deportistas con hombros dolorosos, en los cuales el diagnóstico clínico no era certero. Este trabajo se realizó en 1990 para introducir la técnica artroscópica ...

Influence of gas-generation on melt/concrete interaction

International Nuclear Information System (INIS)

Powers, D.A.

1979-01-01

Gases formed during the interaction of a high-temperature melt with concrete are shown to stem from the thermal dehydration and decarboxylation of the concrete. The kinetics of these decomposition reactions are described. Gases within the melt cause an apparent swelling of the melt. The observed swelling is not easily correlated to the rate of gas evolution. Metallic melts cause CO 2 /CO and H 2 O liberated from the melt to be reduced to CO and hydrogen. When these gases escape from the melt they assist in aerosol formation. As the gases cool they react along a pathway whose oxygen fugacity is apparently buffered by the iron-Wuestite equilibrium. Methane is a product of the gas-phase reaction. (orig./HP) [de

Rhenium corrosion in chloride melts

International Nuclear Information System (INIS)

Stepanov, A.D.; Shkol'nikov, S.N.; Vetyukov, M.M.

1989-01-01

The results investigating rhenium corrosion in chloride melts containing sodium, potassium and chromium ions by a gravimetry potentials in argon atmosphere in a sealing quarth cell are described. Rhenium corrosion is shown to be rather considerable in melts containing CrCl 2 . The value of corrosion rate depending on temperature is determined

UNCONSTRAINED MELTING AND SOLIDIFICATION INSIDE ...

African Journals Online (AJOL)

2015-09-01

Sep 1, 2015 ... There is a large number of experimental and numerical works on melting and solidification of PCM[6-10], and also its usage as thermal management in building [11-14], electronic devices [15-16] and solar energy. [17-20].Most investigated geometries in melting and freezing process are sphere (spherical.

Systeme im Einsatz. Lernmanagement, Kompetenzmanagement und PLE

NARCIS (Netherlands)

Kalz, Marco; Schön, Sandra; Lindner, Martin; Roth, Detlev; Baumgartner, Peter

2011-01-01

Kalz, M., Schön, S., Lindner, M., Roth, D., & Baumgartner, P. (2011). Systeme im Einsatz. Lernmanagement, Kompetenzmanagement und PLE. In M. Ebner, & S. Schön (Eds.), L3T - Lerhbuch für Lernen und Lehren mit Technologie (pp. 111-118). Graz, Austria: Uni Graz. Available at

Shape evolution of a melting nonspherical particle

Science.gov (United States)

Kintea, Daniel M.; Hauk, Tobias; Roisman, Ilia V.; Tropea, Cameron

2015-09-01

In this study melting of irregular ice crystals was observed in an acoustic levitator. The evolution of the particle shape is captured using a high-speed video system. Several typical phenomena have been discovered: change of the particle shape, appearance of a capillary flow of the melted liquid on the particle surface leading to liquid collection at the particle midsection (where the interface curvature is smallest), and appearance of sharp cusps at the particle tips. No such phenomena can be observed during melting of spherical particles. An approximate theoretical model is developed which accounts for the main physical phenomena associated with melting of an irregular particle. The agreement between the theoretical predictions for the melting time, for the evolution of the particle shape, and the corresponding experimental data is rather good.

Melt-quenched glasses of metal-organic frameworks

DEFF Research Database (Denmark)

Bennett, T.D.; Yue, Yuanzheng; Li, P.

2016-01-01

Crystalline solids dominate the field of metal−organic frameworks (MOFs), with access to the liquid and glass states of matter usually prohibited by relatively low temperatures of thermal decomposition. In this work, we give due consideration to framework chemistry and topology to expand...... of other MOFs. The glasses formed upon vitrification are chemically and structurally distinct from the three other existing categories of melt-quenched glasses (inorganic nonmetallic, organic, and metallic), and retain the basic metal−ligand connectivity of crystalline MOFs, which connects their mechanical...... the phenomenon of the melting of 3D MOFs, linking crystal chemistry to framework melting temperature and kinetic fragility of the glass-forming liquids. Here we show that melting temperatures can be lowered by altering the chemistry of the crystalline MOF state, which provides a route to facilitate the melting...

Effect of annealing on the structural and magnetic properties of (Fe{sub 1−x}Co{sub x}){sub 83}B{sub 17} metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Bhagat, Neeru, E-mail: neerubhagat@hotmail.com [Department of Applied Science, Symbiosis Institute of Technology, SIU, Lavale, Mulshi, Pune 412115 (India); Gupta, Ajay [Center for Spintronic Materials, Amity University, Sector 125, Noida (India); Reddy, V.R. [UGC-DAE Consortium for Scientific Research, University Campus, Khandwa Road, Indore (India); Pandey, Brajesh, E-mail: bpandey@gmail.com [Department of Applied Science, Symbiosis Institute of Technology, SIU, Lavale, Mulshi, Pune 412115 (India)

2015-05-01

Amorphous alloys of (Fe{sub 1−x}Co{sub x}){sub 83}B{sub 17} (x=22, 25.3, 28.4) in the vicinity of 25 at% of Co were prepared by melt spun technique. The samples were annealed at different temperatures and the changes in structural and magnetic properties have been studied. Phase stabilization and magnetic properties of amorphous alloys were studies using X-ray diffraction and Mössbauer spectroscopy. The result shows anomalies in structure and in magnetic properties in the studied samples. Annealing at 475 °C brings about the formation of complete and stable crystalline structure. At this stage multiple crystalline phases have been observed. Mössbauer spectroscopy also revealed that two phases of Fe{sub 3}B were formed along with stable Fe{sub 3}Co phase. - Highlights: • Using melt spun technique alloys of (Fe{sub 1−x}Co{sub x}){sub 83}B{sub 17} (x=22, 25.3, 28.4) in amorphous phase were prepared. • Crystalline phase increases with increasing the Co concentration. • Appearance of one crystalline phase is observed when samples annealing at 345 °C. • Annealing at higher temperature leads to emergence of multiple crystalline phases. • Different phases of Fe–Co, and Fe–Co–B were identified.

How IMS Enables Converged Services for Cable and 3G Technologies: A Survey

Directory of Open Access Journals (Sweden)

Noël Crespi

2008-04-01

Full Text Available The IP multimedia subsystem (IMS is a service control overlay standardized by the 3GPP. The IMS is based on session initiation protocol (SIP to establish, modify, and terminate the sessions. It provides a clean separation between services, signaling, and media with the potential to enable control and management of services over multiple transport technologies. In the scope of fixed-mobile convergence, this paper is dedicated to presenting a review of how cable networks can be integrated into IMS technology to achieve 3G-cable horizontal convergence. Cable networks, as one of the major fixed broadband access technologies with PacketCable architecture, are able to provide broadband internet access and VoIP in addition to cable TV. In this article, we review the evolution in PacketCable architecture to take up IMS. In this way, we consider the standardization and research activities to address this integration. We review some important challenges such as SIP protocol compatibility, defining unique user profile, required enhancement in authentication process, QoS and charging system.

How IMS Enables Converged Services for Cable and 3G Technologies: A Survey

Directory of Open Access Journals (Sweden)

Mani Mehdi

2008-01-01

Full Text Available The IP multimedia subsystem (IMS is a service control overlay standardized by the 3GPP. The IMS is based on session initiation protocol (SIP to establish, modify, and terminate the sessions. It provides a clean separation between services, signaling, and media with the potential to enable control and management of services over multiple transport technologies. In the scope of fixed-mobile convergence, this paper is dedicated to presenting a review of how cable networks can be integrated into IMS technology to achieve 3G-cable horizontal convergence. Cable networks, as one of the major fixed broadband access technologies with PacketCable architecture, are able to provide broadband internet access and VoIP in addition to cable TV. In this article, we review the evolution in PacketCable architecture to take up IMS. In this way, we consider the standardization and research activities to address this integration. We review some important challenges such as SIP protocol compatibility, defining unique user profile, required enhancement in authentication process, QoS and charging system.

Melt inclusion: methods, applications and problem: Silica-rich melts in quartz xenoliths from Vulcano islands and their bearing on processes of crustal melting and crust-magma interaction in the Aeolian Arc, Italy

NARCIS (Netherlands)

Frezzotti, M.L.; Zavon, V.; Peccerillo, A.; Nikogosian, I.

2002-01-01

Silica-rich melts in quartz xenoliths from Vulcano islands and their bearing on processes of crustal melting and crust-magma interaction in the Aeolian Arc, Italy Proceedings of workshop Melt inclusion: methods, applications and problem. Napoli, Italy, September 2002, p. 71-73

Study on superheat of TiAl melt during cold crucible levitation melting. TiAl no cold crucible levitation yokai ni okeru yoto kanetsudo no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Miwa, K.; Kobayashi, K.; Ninomiya, M. (Government Industrial Research Institute, Nagoya, Nagoya (Japan))

1992-06-20

Investigations were given on effects of test sample weights and sample positions in cold crucibles on superheat of melts when the intermetallic compound TiAl is melted using cold crucible levitation melting process, one of noncontaminated melting processes. The cold crucibles used in the experiment are a water-cooled copper crucible with an inner diameter of 42 mm and a length of 140 mm, into which a column-like ingot sample with an outer diameter of 32 mm (Al containing Ti at 33.5% by mass) was put and melted using the levitation melting. Comparisons and discussions were given on the relationship between sample weights and melt temperatures, the relationship between positions of the inserted samples and melt temperatures, and the state of contamination at melting of casts obtained from the melts resulted from the levitation melting and high-frequency melting poured into respective ceramic dies. Elevating the superheat temperature of the melts requires optimizing the sample weights and positions. Melt temperatures were measured using a radiation thermometer and a thermocouple, and the respective measured values were compared. 7 refs., 4 figs., 1 tab.

Evaluation of the Indian Migration Study Physical Activity Questionnaire (IMS-PAQ: a cross-sectional study

Directory of Open Access Journals (Sweden)

Sullivan Ruth

2012-02-01

Full Text Available Abstract Background Socio-cultural differences for country-specific activities are rarely addressed in physical activity questionnaires. We examined the reliability and validity of the Indian Migration Study Physical Activity Questionnaire (IMS-PAQ in urban and rural groups in India. Methods A sub-sample of IMS participants (n = 479 was used to examine short term (≤1 month [n = 158] and long term (> 1 month [n = 321] IMS-PAQ reliability for levels of total, sedentary, light and moderate/vigorous activity (MVPA intensity using intraclass correlation (ICC and kappa coefficients (k. Criterion validity (n = 157 was examined by comparing the IMS-PAQ to a uniaxial accelerometer (ACC worn ≥4 days, via Spearman's rank correlations (ρ and k, using Bland-Altman plots to check for systematic bias. Construct validity (n = 7,000 was established using linear regression, comparing IMS-PAQ against theoretical constructs associated with physical activity (PA: BMI [kg/m2], percent body fat and pulse rate. Results IMS-PAQ reliability ranged from ICC 0.42-0.88 and k = 0.37-0.61 (≤1 month and ICC 0.26 to 0.62; kappa 0.17 to 0.45 (> 1 month. Criterion validity was ρ = 0.18-0.48; k = 0.08-0.34. Light activity was underestimated and MVPA consistently and substantially overestimated for the IMS-PAQ vs. the accelerometer. Criterion validity was moderate for total activity and MVPA. Reliability and validity were comparable for urban and rural participants but lower in women than men. Increasing time spent in total activity or MVPA, and decreasing time in sedentary activity were associated with decreasing BMI, percent body fat and pulse rate, thereby demonstrating construct validity. Conclusion IMS-PAQ reliability and validity is similar to comparable self-reported instruments. It is an appropriate tool for ranking PA of individuals in India. Some refinements may be required for sedentary populations and women in India.

Simulation of melt spreading in consideration of phase transitions

Energy Technology Data Exchange (ETDEWEB)

Spengler, C. [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, Koeln (Germany)

2002-07-01

The analysis of melt spreading and relocation phenomena in the containment of LWR power plants in case of hypothetical severe accidents leading to core melting is an important issue for reactor safety investigations. For the simulation of melt spreading the code LAVA has been developed on the basis of a method from the related subject of volcanology by adding more detailed models for heat transfer phenomena and flow rheology. The development is supported by basic analysis of the spreading of gravity currents as well as experimental investigations of the rheology of solidifying melts. These exhibit strong non-Newtonian effects in case of a high content of solids in the freezing melt. The basic model assumption in LAVA is the ideal Bingham plastic approach to the non-Newtonian, shear-thinning characteristic of solidifying melts. For the recalculation of melt spreading experiments, the temperature-dependent material properties for solidifying melt mixtures have been calculated using correlations from the literature. With the parameters and correlations for the rheological material properties approached by results from literature, it was possible to recalculate successfully recent spreading experiments with simulant materials and prototypic reactor core materials. An application to the behaviour of core melt in the reactor cavity assumed a borderline case for the issue of spreading. This limit is represented by melt conditions (large solid fraction, low volume flux), under which the melt is hardly spreadable. Due to the persistent volume flux the reactor cavity is completely, but inhomogeneously filled with melt. The degree of inhomogeneity is rather small, so it is concluded, that for the long-term coolability of a melt pool in narrow cavities the spreading of melt will probably have only negligible influence. (orig.)

An IMS-Based Middleware Solution for Energy-Efficient and Cost-Effective Mobile Multimedia Services

Science.gov (United States)

Bellavista, Paolo; Corradi, Antonio; Foschini, Luca

Mobile multimedia services have recently become of extreme industrial relevance due to the advances in both wireless client devices and multimedia communications. That has motivated important standardization efforts, such as the IP Multimedia Subsystem (IMS) to support session control, mobility, and interoperability in all-IP next generation networks. Notwithstanding the central role of IMS in novel mobile multimedia, the potential of IMS-based service composition for the development of new classes of ready-to-use, energy-efficient, and cost-effective services is still widely unexplored. The paper proposes an original solution for the dynamic and standard-compliant redirection of incoming voice calls towards WiFi-equipped smart phones. The primary design guideline is to reduce energy consumption and service costs for the final user by automatically switching from the 3G to the WiFi infrastructure whenever possible. The proposal is fully compliant with the IMS standard and exploits the recently released IMS presence service to update device location and current communication opportunities. The reported experimental results point out that our solution, in a simple way and with full compliance with state-of-the-art industrially-accepted standards, can significantly increase battery lifetime without negative effects on call initiation delay.

Antisemitismus, Shoah und deutsche Verantwortung:(Nach)Wirkungen des Nationalsozialismus im medialen Nahostdiskurs

OpenAIRE

Ullrich, Peter

2010-01-01

Wahrscheinlich wird kein anderer internationaler Konflikt derart kontrovers und emotional in der bundesrepublikanischen Öffentlichkeit sowie auch und gerade in der politischen Linken diskutiert wie der israelisch-palästinensische oder weiter gefasst, der Nahost-Konflikt. Aus diesem Grund nimmt dieses Thema einen besonderen Platz in der Bildungsarbeit der Rosa-Luxemburg- Stiftung im Inland wie im Ausland ein. Wenngleich dabei auch in der Stiftung und ihrem Umfeld die Meinungen auseinandergehen...

Magnetic susceptibility of semiconductor melts

International Nuclear Information System (INIS)

Kutvitskij, V.A.; Shurygin, P.M.

1975-01-01

The temperature dependences chi of various alloys confirm the existence of cluster formations in molten semiconductors, the stability of these formations in melts being considerably affected by the anion nature. The concentrational dependences of the magnetic susceptibility for all the investigated systems exhibit the diamagnetism maxima corresponding to the compound compositions. Heating the melt causes ''smearing'' the maxima, which is related with the cluster structure dissociation. The existence of the maxima concentrational dependence chi corresponding to BiTe and BiSe is found in the isotherms. The non-linear dependence of chi on the composition shows the absence of a single-valued relation between the phase diagram and the chi-diagram for melts

Vacancies and a generalised melting curve of metals

International Nuclear Information System (INIS)

Gorecki, T.

1979-01-01

The vacancy mechanism of the melting process is used as a starting point for deriving an expression for the pressure dependence of the melting temperature of metals. The results obtained for the initial slope of the melting curve are compared with experimental data for 45 metals and in most cases the agreement is very good. The nonlinearity of the melting curve and the appearance of a maximum on the melting curve at a pressure approximately equal to the bulk modules is also predicted, with qualitative agreement with experimental data. A relation between bonding energy, atomic volume, and bulk modulus of metals is established. On the basis of this relation and the proposed vacancy mechanism, a generalised equation for the pressure dependence of the melting temperature of metals is derived. (author)

Lessons learnt from FARO/TERMOS corium melt quenching experiments

Energy Technology Data Exchange (ETDEWEB)

Magallon, D.; Huhtiniemi, I.; Hohmann, H. [Commission of the European Communities, Ispra (Italy). Joint Research Center

1998-01-01

The influence of melt quantity, melt composition, water depth and initial pressure on quenching is assessed on the basis of seven tests performed in various conditions in the TERMOS vessel of the FARO facility at JRC-Ispra. Tests involved UO{sub 2}-based melt quantities in the range 18-176 kg at a temperature of approximately 3000 K poured into saturated water. The results suggest that erosion of the melt jet column is an efficient contributor to the amount of break-up, and thus quenching, for large pours of corium melt. The presence of Zr metal in the melt induced a much more efficient quenching than in a similar test with no Zr metal, attributed to the oxidation of the Zr. Significant amounts of H{sub 2} were produced also in tests with pure oxidic melts (e.g. about 300 g for 157 kg melt). In the tests at 5.0 and 2.0 MPa good mixing with significant melt break-up and quenching was obtained during the penetration in the water. At 0.5 MPa, good penetration of the melt into the water could still be achieved, but a jump in the vessel pressurisation occurred when the melt contacted the bottom and part (5 kg) of the debris was re-ejected from the water. (author)

Melting of gold microclusters

International Nuclear Information System (INIS)

Garzon, I.L.; Jellinek, J.

1991-01-01

The transition from solid-like to liquid-like behavior in Au n , n=6, 7, 13, clusters is studied using molecular dynamics simulations. A Gupta-type potential with all-neighbour interactions is employed to incorporate n-body effects. The melting-like transition is described in terms of short-time averages of the kinetic energy per particle, root-mean-square bond length fluctuations and mean square displacements. A comparison between melting temperatures of Au n and Ni n clusters is presented. (orig.)

Improved capacitive melting curve measurements

International Nuclear Information System (INIS)

Sebedash, Alexander; Tuoriniemi, Juha; Pentti, Elias; Salmela, Anssi

2009-01-01

Sensitivity of the capacitive method for determining the melting pressure of helium can be enhanced by loading the empty side of the capacitor with helium at a pressure nearly equal to that desired to be measured and by using a relatively thin and flexible membrane in between. This way one can achieve a nanobar resolution at the level of 30 bar, which is two orders of magnitude better than that of the best gauges with vacuum reference. This extends the applicability of melting curve thermometry to lower temperatures and would allow detecting tiny anomalies in the melting pressure, which must be associated with any phenomena contributing to the entropy of the liquid or solid phases. We demonstrated this principle in measurements of the crystallization pressure of isotopic helium mixtures at millikelvin temperatures by using partly solid pure 4 He as the reference substance providing the best possible universal reference pressure. The achieved sensitivity was good enough for melting curve thermometry on mixtures down to 100 μK. Similar system can be used on pure isotopes by virtue of a blocked capillary giving a stable reference condition with liquid slightly below the melting pressure in the reference volume. This was tested with pure 4 He at temperatures 0.08-0.3 K. To avoid spurious heating effects, one must carefully choose and arrange any dielectric materials close to the active capacitor. We observed some 100 pW loading at moderate excitation voltages.

Differential melt scaling for oblique impacts on terrestrial planets

Science.gov (United States)

Abramov, Oleg; Wong, Stephanie M. Wong; Kring, David A. Kring

2012-01-01

Analytical estimates of melt volumes produced by a given projectile and contained in a given impact crater are derived as a function of impact velocity, impact angle, planetary gravity, target and projectile densities, and specific internal energy of melting. Applications to impact events and impact craters on the Earth, Moon, and Mars are demonstrated and discussed. The most probable oblique impact (45°) produces ∼1.6 times less melt volume than a vertical impact, and ∼1.6 and 3.7 times more melt volume than impacts with 30° and 15° trajectories, respectively. The melt volume for a particular crater diameter increases with planetary gravity, so a crater on Earth should have more melt than similar-size craters on Mars and the Moon. The melt volume for a particular projectile diameter does not depend on gravity, but has a strong dependence on impact velocity, so the melt generated by a given projectile on the Moon is significantly larger than on Mars. Higher surface temperatures and geothermal gradients increase melt production, as do lower energies of melting. Collectively, the results imply thinner central melt sheets and a smaller proportion of melt particles in impact breccias on the Moon and Mars than on Earth. These effects are illustrated in a comparison of the Chicxulub crater on Earth, linked to the Cretaceous–Tertiary mass extinction, Gusev crater on Mars, where the Mars Exploration Rover Spirit landed, and Tsiolkovsky crater on the Moon. The results are comparable to those obtained from field and spacecraft observations, other analytical expressions, and hydrocode simulations.