WorldWideScience

Sample records for median electricity savings

  1. Electric energy savings from new technologies

    Energy Technology Data Exchange (ETDEWEB)

    Moe, R.J.; Harrer, B.J.; Kellogg, M.A.; Lyke, A.J.; Imhoff, K.L.; Fisher, Z.J.

    1986-01-01

    Purpose of the report is to provide information about the electricity-saving potential of new technologies to OCEP that it can use in developing alternative long-term projections of US electricity consumption. Low-, base-, and high-case scenarios of the electricity savings for ten technologies were prepared. The total projected annual savings for the year 2000 for all ten technologies were 137 billion kilowatt hours (BkWh), 279 BkWh, and 470 BkWh, respectively, for the three cases. The magnitude of these savings projections can be gauged by comparing them to the Department's reference case projection for the 1985 National Energy Policy Plan. In the Department's reference case, total consumption in 2000 is projected to be 3319 BkWh. Thus, the savings projected here represent between 4% and 14% of total consumption projected for 2000. Because approximately 75% of the base-case estimate of savings are already incorporated into the reference forecast, reducing projected electricity consumption from what it otherwise would have been, the savings estimated here should not be directly subtracted from the reference forecast.

  2. Saving electricity in a hurry - update 2011

    Energy Technology Data Exchange (ETDEWEB)

    Pasquier, Sara Bryan

    2011-06-15

    As demonstrated by the March 2011 earthquake and tsunami-triggered blackouts in Japan, electricity shortfalls can happen anytime and anywhere. Countries can minimise the negative economic, social and environmental impacts of such electricity shortfalls by developing emergency energy-saving strategies before a crisis occurs. This new IEA report highlights preliminary findings and conclusions from electricity shortfalls in Japan, the United States, New Zealand, South Africa and Chile. It draws on recent analysis to: reinforce well-established guidelines on diagnosing electricity shortfalls, identifying energy-saving opportunities and selecting a package of energy-saving measures; and highlight proven practice for implementing emergency energy-saving programmes. This paper will be valuable to government, academic, private-sector and civil-society stakeholders who inform, develop and implement electricity policy in general, and emergency energy-saving programmes in particular.

  3. Electric power production contra electricity savings

    International Nuclear Information System (INIS)

    Schleisner, L.; Grohnheit, P.E.; Soerensen, H.

    1991-01-01

    The expansion of electricity-producing plants has, in Denmark until now, taken place in accordance with the demand for electricity. Recently, it has been suggested that the cost of the further development of such systems is greater than the cost of instigating and carrying out energy conservation efforts. The aim of the project was to evaluate the consequences for power producing plants of a reduction of the electricity consumption of end-users. A method for the analysis of the costs involved in the system and operation of power plants contra the costs that are involved in saving electricity is presented. In developing a model of this kind, consideration is given to the interplay of the individual saving project and the existing or future electricity supply. Thus it can be evaluated to what extent it would be advisable to substitute investments in the development of the capacity of the power plants with investments in the reduction of electricity consumption by the end users. This model is described in considerable detail. It will be tested in representative situations and locations throughout the Nordic countries. (AB) 17 refs

  4. Electricity saving in households-A social cognitive approach

    International Nuclear Information System (INIS)

    Thogersen, John; Gronhoj, Alice

    2010-01-01

    We propose a conceptual framework for understanding the (lack of) energy saving efforts of private households based on Bandura's (1986) social cognitive theory. Results from applying this framework on a sample of Danish private electricity consumers are presented and it is concluded (a) that households' electricity consumption depends on both structural and motivational factors, (b) that their electricity saving effort depends on the strength of their internalized norms or self-expectations and on self-efficacy related factors, and (c) that there are predictable patterns of interaction among household members that influence their electricity consumption. The results suggest two approaches to promote electricity saving in households: (1) to change the socio-structural environment to be more facilitating for energy saving and empower householders to be more effective in their striving towards this goal through improved feedback about their household's electricity consumption and (2) social norms marketing, communicating social expectations and others' successful electricity saving achievements. - Research highlights: →A combination of survey and meter reading data is used to analyze energy saving in households. →Up to two adults from each household answered the questionnaire. →Dyadic data analysis is used to investigate interactions between household members. →Both structural and motivational factors account for households' electricity consumption. →Electricity saving efforts depends on internalized norms, self-efficacy and social interaction.

  5. Electricity saving in households-A social cognitive approach

    Energy Technology Data Exchange (ETDEWEB)

    Thogersen, John, E-mail: jbt@asb.d [Aarhus University, School of Business and Social Sciences, Department of Marketing, Haslegaardsvej 10, DK-8210 Aarhus (Denmark); Gronhoj, Alice, E-mail: alg@asb.d [Aarhus University, School of Business and Social Sciences, Department of Marketing, Haslegaardsvej 10, DK-8210 Aarhus (Denmark)

    2010-12-15

    We propose a conceptual framework for understanding the (lack of) energy saving efforts of private households based on Bandura's (1986) social cognitive theory. Results from applying this framework on a sample of Danish private electricity consumers are presented and it is concluded (a) that households' electricity consumption depends on both structural and motivational factors, (b) that their electricity saving effort depends on the strength of their internalized norms or self-expectations and on self-efficacy related factors, and (c) that there are predictable patterns of interaction among household members that influence their electricity consumption. The results suggest two approaches to promote electricity saving in households: (1) to change the socio-structural environment to be more facilitating for energy saving and empower householders to be more effective in their striving towards this goal through improved feedback about their household's electricity consumption and (2) social norms marketing, communicating social expectations and others' successful electricity saving achievements. - Research highlights: {yields}A combination of survey and meter reading data is used to analyze energy saving in households. {yields}Up to two adults from each household answered the questionnaire. {yields}Dyadic data analysis is used to investigate interactions between household members. {yields}Both structural and motivational factors account for households' electricity consumption. {yields}Electricity saving efforts depends on internalized norms, self-efficacy and social interaction.

  6. Electricity saving in households. A social cognitive approach

    Energy Technology Data Exchange (ETDEWEB)

    Thoegersen, John; Groenhoej, Alice [Aarhus University, School of Business and Social Sciences, Department of Marketing, Haslegaardsvej 10, DK-8210 Aarhus (Denmark)

    2010-12-15

    We propose a conceptual framework for understanding the (lack of) energy saving efforts of private households based on Bandura's (1986) social cognitive theory. Results from applying this framework on a sample of Danish private electricity consumers are presented and it is concluded (a) that households' electricity consumption depends on both structural and motivational factors, (b) that their electricity saving effort depends on the strength of their internalized norms or self-expectations and on self-efficacy related factors, and (c) that there are predictable patterns of interaction among household members that influence their electricity consumption. The results suggest two approaches to promote electricity saving in households: (1) to change the socio-structural environment to be more facilitating for energy saving and empower householders to be more effective in their striving towards this goal through improved feedback about their household's electricity consumption and (2) social norms marketing, communicating social expectations and others' successful electricity saving achievements. (author)

  7. Electricity consumption and electricity saving in the Swedish households

    Energy Technology Data Exchange (ETDEWEB)

    Bernstroem, B M; Eklund, Y; Sjoeberg, L

    1997-03-01

    The objective of the present study is to determine which factors influence electricity consumption behavior of Swedish households, the level of knowledge about electricity use and the willingness to pay for the use of electricity. In Sweden, as in many other developed countries, the need for electric power is constantly increasing. The major reason for this increase in electricity consumption is the lifestyle of a modern society. A feature in the nuclear power discussion is that the government in Sweden is having a hard time to establish how to phase-out all nuclear power plants by 2010. An additional major change in Swedish energy policy is the deregulation of the electricity market, which started in the beginning of 1996. There is an increased demand for strategies to save electricity among households. The results of this study stress the difficulties in reducing electricity consumption and to develop new electricity saving strategies in Sweden 125 refs, 6 figs, 21 tabs

  8. Saving electricity in a hurry. Dealing with temporary shortfalls in electricity supplies

    Energy Technology Data Exchange (ETDEWEB)

    none

    2005-07-01

    Blackouts are normally the result of imbalances in electricity supply and demand. A brief blackout is mostly an inconvenience. But persistent shortfalls ? those lasting days, weeks, or months ? can cause economic disruption and danger to human life in our technology-rich societies. Saving Electricity in a Hurry describes some of the recent power shortfalls, from Norway to New Zealand, from Tokyo to Arizona and the policies these regions used to quickly reduce their power consumption. How did the whole country of Sweden cut its power consumption by 4% in only three days? How did California save 14% in only a few months? While the temporary shortfalls in electricity supplies described in this book are relatively rare events, they disproportionately shape future energy policies. Saving Electricity in a Hurry shows that countries can quickly reduce electricity consumption without harming the economy as much as blackouts or unplanned curtailments. The strategies are diverse, unique and often surprisingly cheap. They include mass media campaigns ? where a good joke can save a Megawatt ? improvements in equipment efficiency and quickly adjusting electricity prices. This book explains how California replaced a million traffic signals with energy-saving models, how millions of Tokyo residents raised their thermostat settings, and how New Zealanders took shorter showers, all quickly enough to help avoid imminent blackouts. Finally, it connects these policies to the traditional goal of ?saving electricity slowly?.

  9. How to Organize Electricity Savings in a Liberalized Electricity Market

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen

    1998-01-01

    The basic idea of Integrated Ressource Planning is described and it is demonstrated how this is in conflict with the sub-optimizing necessary in a liberalized market. Afterwards are outlined how the measuring of savings energy consumption constitutes a fundamental problem. Finally are dicussed...... the future actors in the electricity sector and their roles in implementing electricity savings, followed by some proposals for an energy policy....

  10. Public administration electricity savings. Offentlige energibesparelser; Nyere danske erfaringer

    Energy Technology Data Exchange (ETDEWEB)

    Gjelstrup, G

    1991-01-01

    Analysis on how different types of public authorities experienced carrying out electricity savings showed that the individual public authority's internal political-administrative organizational form is of major importance for the possibilities of realizing potential electricity savings. In addition, it can be concluded that only certain public authorities have utilized external assistance in connection with effecting electricity savings. In these cases there has been some accordance between the particular authority's internal, political-administrative, organization and the organizational form presupposed in the external assistance offered. In spite of this, the public authorities in question have, in general, not progressed very far with electricity savings. Part of the reason for this lies namely in the fact that the special importance the mode of organization has for electricity savings, has been overlooked in this type of assistance. (CLS) 43 refs.

  11. Public administration electricity savings. Offentlige energibesparelser; Nyere danske erfaringer

    Energy Technology Data Exchange (ETDEWEB)

    Gjelstrup, G.

    1991-01-01

    Analysis on how different types of public authorities experienced carrying out electricity savings showed that the individual public authority's internal political-administrative organizational form is of major importance for the possibilities of realizing potential electricity savings. In addition, it can be concluded that only certain public authorities have utilized external assistance in connection with effecting electricity savings. In these cases there has been some accordance between the particular authority's internal, political-administrative, organization and the organizational form presupposed in the external assistance offered. In spite of this, the public authorities in question have, in general, not progressed very far with electricity savings. Part of the reason for this lies namely in the fact that the special importance the mode of organization has for electricity savings, has been overlooked in this type of assistance. (CLS) 43 refs.

  12. Electric energy savings from new technologies. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Harrer, B.J.; Kellogg, M.A.; Lyke, A.J.; Imhoff, K.L.; Fisher, Z.J.

    1986-09-01

    Purpose of the report is to provide information about the electricity-saving potential of new technologies to OCEP that it can use in developing alternative long-term projections of US electricity consumption. Low-, base-, and high-case scenarios of the electricity savings for 10 technologies were prepared. The total projected annual savings for the year 2000 for all 10 technologies were 137 billion kilowatt hours (BkWh), 279 BkWh, and 470 BkWh, respectively, for the three cases. The magnitude of these savings projections can be gauged by comparing them to the Department's reference case projection for the 1985 National Energy Policy Plan. In the Department's reference case, total consumption in 2000 is projected to be 3319 BkWh. Because approximately 75% of the base-case estimate of savings are already incorporated into the reference projection, only 25% of the savings estimated here should be subtracted from the reference projection for analysis purposes.

  13. Determinants and policy implications for household electricity-saving behaviour: Evidence from Beijing, China

    International Nuclear Information System (INIS)

    Wang Zhaohua; Zhang Bin; Yin Jianhua; Zhang Yixiang

    2011-01-01

    This research sets out to explore the possibilities for further saving in household electricity consumption through a study of the residents' willingness and behavioural characteristics in electricity saving, as applied within a Chinese context. Based on an extensive literature review, the authors argue that economic benefits, policy and social norms, and past experience may have a positive correlation with household electricity-saving behaviour, while the discomfort caused by electricity-saving activities, may exert a negative effect on it. Through a sample of 816 randomly selected residents in Beijing, the propositions are examined using logit regression analysis. The conclusions support the ideas, concerning both the positive influence of economic benefits, policy and social norms, and past experience as they affect broader electricity-saving behaviour, and the negative influence of the discomfort caused by electricity-saving activities. Finally, some inferences are drawn, and suggestions are offered for policy makers and further studies. - Highlights: → We develop a logistic regression to investigate household electricity saving behaviour. → Determinants for household electricity saving are verified with a questionnaire survey. → Environmental awareness does not impact on household electricity saving directly. → It is prerequisite to focus on both financial subsidy and technology improvement. → Tiered price reform is considered an effective policy for electricity saving.

  14. Real-time pricing when some consumers resist in saving electricity

    International Nuclear Information System (INIS)

    Salies, Evens

    2013-01-01

    Successful real-time electricity pricing depends firstly upon consumers' willingness to subscribe to such terms and, secondly, on their ability to curb consumption levels. The present paper addresses both issues by considering consumers differentiated by their electricity saving costs, half of whom resist saving electricity. We demonstrate that when consumers are free to adopt real-time prices, producers prefer charging inefficient prices and, in so doing, discriminate against that portion of the consumer population which faces no saving costs. We also find that efficient marginal cost pricing is feasible, but is incompatible with mass adoption of real-time prices. - Highlights: • We model consumers switching from uniform to real-time electricity pricing (RTP). • Half the consumer population is pro-RTP and half resists saving electricity. • Efficient RTP is feasible but is incompatible with mass adoption

  15. Identifying electricity-saving potential in rural China: Empirical evidence from a household survey

    International Nuclear Information System (INIS)

    Yu, Yihua; Guo, Jin

    2016-01-01

    In recent years, there has been a fast-growing body of literature examining energy-saving potential in relation to electricity. However, empirical studies focusing on non-Western nations are limited. To fill this gap, this study intends to examine the electricity-saving potential of rural households in China using a unique data set from the China Residential Electricity Consumption Survey (CRECS) in collaboration with the China General Social Survey (CGSS), conducted nationwide at the household level in rural China. We use a stochastic frontier model, which allows us to decompose residential electricity consumption into the minimum necessary amount of consumption based on physical characteristics (e.g. house size, house age, number of televisions or refrigerators) and estimate the consumption slack (i.e. the amount of electricity consumption that could be saved), which depends on various factors. We find that rural households in China are generally efficient in electricity saving and the saving potential is affected by (fast) information feedback and social-demographic characteristics, instead of by the (averaged) electricity price, or energy efficiency labelling signals. In addition, we find no evidence of regional heterogeneity on electricity saving potential for rural households. Policy implications are derived. - Highlights: •Electricity saving potential of rural households in China is examined. •Unique survey data from the CRECS in collaboration with the CGSS are used. •A stochastic frontier model is applied. •Information feedback and social-demographic characteristics matter. •Electricity price or energy efficiency tier rating does not matter.

  16. Effects of heat and electricity saving measures in district-heated multistory residential buildings

    International Nuclear Information System (INIS)

    Truong, Nguyen Le; Dodoo, Ambrose; Gustavsson, Leif

    2014-01-01

    Highlights: • We analyzed the potential for energy savings in district heated buildings. • Measures that reduce more peak load production give higher primary energy savings. • Efficient appliances increase heat demand but give net primary energy savings. • Efficient appliances give the largest net primary energy savings. - Abstract: The effects of heat and electricity saving measures in district-heated buildings can be complex because these depend not only on how energy is used on the demand side but also on how energy is provided from the supply side. In this study, we analyze the effects of heat and electricity saving measures in multistory concrete-framed and wood-framed versions of an existing district-heated building and examine the impacts of the reduced energy demand on different district heat (DH) production configurations. The energy saving measures considered are for domestic hot water reduction, building thermal envelope improvement, ventilation heat recovery (VHR), and household electricity savings. Our analysis is based on a measured heat load profile of an existing DH production system in Växjö, Sweden. Based on the measured heat load profile, we model three minimum-cost DH production system using plausible environmental and socio-political scenarios. Then, we investigate the primary energy implications of the energy saving measures applied to the two versions of the existing building, taking into account the changed DH demand, changed cogenerated electricity, and changed electricity use due to heat and electricity saving measures. Our results show that the difference between the final and primary energy savings of the concrete-framed and wood-framed versions of the case-study building is minor. The primary energy efficiency of the energy saving measures depends on the type of measure and on the composition of the DH production system. Of the various energy saving measures explored, electricity savings give the highest primary energy savings

  17. Antecedents of employee electricity saving behavior in organizations: An empirical study based on norm activation model

    International Nuclear Information System (INIS)

    Zhang, Yixiang; Wang, Zhaohua; Zhou, Guanghui

    2013-01-01

    China is one of the major energy-consuming countries, and is under great pressure to promote energy saving and reduce domestic energy consumption. Employees constitute an important target group for energy saving. However, only a few research efforts have been paid to study what drives employee energy saving behavior in organizations. To fill this gap, drawing on norm activation model (NAM), we built a research model to study antecedents of employee electricity saving behavior in organizations. The model was empirically tested using survey data collected from office workers in Beijing, China. Results show that personal norm positively influences employee electricity saving behavior. Organizational electricity saving climate negatively moderates the effect of personal norm on electricity saving behavior. Awareness of consequences, ascription of responsibility, and organizational electricity saving climate positively influence personal norm. Furthermore, awareness of consequences positively influences ascription of responsibility. This paper contributes to the energy saving behavior literature by building a theoretical model of employee electricity saving behavior which is understudied in the current literature. Based on the empirical results, implications on how to promote employee electricity saving are discussed. - Highlights: • We studied employee electricity saving behavior based on norm activation model. • The model was tested using survey data collected from office workers in China. • Personal norm positively influences employee′s electricity saving behavior. • Electricity saving climate negatively moderates personal norm′s effect. • This research enhances our understanding of employee electricity saving behavior

  18. Estimating the potential for electricity savings in households

    International Nuclear Information System (INIS)

    Boogen, Nina

    2017-01-01

    Improving efficiency in the use of energy is an important goal for many nations since end-use energy efficiency can help to reduce CO_2 emissions. Furthermore, since the residential sector in industrialised countries requires around one third of the end-use electricity, it is important for policy makers to estimate the scope for electricity saving in households to reduce electricity consumption by using appropriate steering mechanisms. We estimate the level of technical efficiency in the use of electricity using data from a Swiss household survey. We find an average inefficiency in electricity use by Swiss households of around 20 to 25%. Bottom-up economic-engineering models estimate the potential in Switzerland to be around 15%. In this paper we use a sub-vector input distance frontier function based on economic foundations. Our estimates lie at the upper end of the electricity saving potential estimated by the afore-mentioned economic-engineering approach. - Highlights: • We estimate the level of efficiency in the use of electricity by Swiss households. • We apply a non-radial input distance function and stochastic frontier methods. • We use data from two waves of a Swiss household survey conducted in 2005 and 2011. • We find an inefficiency in the use of electricity of around 20–25%.

  19. LED Lightbulbs as a Source of Electricity Saving in Buildings

    Directory of Open Access Journals (Sweden)

    Zeb Akhtar

    2016-01-01

    Full Text Available Today a number of renewable energy technologies are available for power generation, but fossil fuels are still providing a dominant share nevertheless. In order to decrease the electric bill and save our environment, energy conservation is always crucial. In this paper a very interesting idea is presented which is economically viable to reduce electricity usage in our buildings. An effort has been made to estimate the amount of energy that could be saved in the dormitory section of the IMOP building in Russia. Although there are many ways to reduce the consumption of electricity in this building but here the emphasis is on changing light bulbs inside the rooms, kitchen, toilet and bathroom of each apartment. The scope of the study is to figure out monthly electricity saving by replacing traditional light bulbs by LED light bulbs in the building under consideration. The total investment required and the payback period is also presented.

  20. Estimating customer electricity savings from projects installed by the U.S. ESCO industry

    Energy Technology Data Exchange (ETDEWEB)

    Carvallo, Juan Pablo [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States); Larsen, Peter H. [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States); Goldman, Charles A. [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States)

    2014-11-25

    The U.S. energy service company (ESCO) industry has a well-established track record of delivering substantial energy and dollar savings in the public and institutional facilities sector, typically through the use of energy savings performance contracts (ESPC) (Larsen et al. 2012; Goldman et al. 2005; Hopper et al. 2005, Stuart et al. 2013). This ~$6.4 billion industry, which is expected to grow significantly over the next five years, may play an important role in achieving demand-side energy efficiency under local/state/federal environmental policy goals. To date, there has been little or no research in the public domain to estimate electricity savings for the entire U.S. ESCO industry. Estimating these savings levels is a foundational step in order to determine total avoided greenhouse gas (GHG) emissions from demand-side energy efficiency measures installed by U.S. ESCOs. We introduce a method to estimate the total amount of electricity saved by projects implemented by the U.S. ESCO industry using the Lawrence Berkeley National Laboratory (LBNL) /National Association of Energy Service Companies (NAESCO) database of projects and LBNL’s biennial industry survey. We report two metrics: incremental electricity savings and savings from ESCO projects that are active in a given year (e.g., 2012). Overall, we estimate that in 2012 active U.S. ESCO industry projects generated about 34 TWh of electricity savings—15 TWh of these electricity savings were for MUSH market customers who did not rely on utility customer-funded energy efficiency programs (see Figure 1). This analysis shows that almost two-thirds of 2012 electricity savings in municipal, local and state government facilities, universities/colleges, K-12 schools, and healthcare facilities (i.e., the so-called “MUSH” market) were not supported by a utility customer-funded energy efficiency program.

  1. Replacement or additional purchase: The impact of energy-efficient appliances on household electricity saving under public pressures

    International Nuclear Information System (INIS)

    Mizobuchi, Kenichi; Takeuchi, Kenji

    2016-01-01

    This study examined the influence of additional and replacement purchases of energy-efficient air-conditioners on power savings. We used a questionnaire survey and measured electricity use data from 339 Japanese households, collected from two city areas with different level of government-requested electricity-saving rates, namely, Osaka (10%) and Matsuyama (5%). The main findings of our study are as follows: (1) Households that purchased energy-efficient air-conditioners saved more electricity than those that did not. (2) “Additional-purchase households” showed significant energy savings, whereas “replacement households” did not. The rebound effect may negate the energy-saving effects of a new air-conditioner. (3) Altruistic attitude is associated with more active participation in power saving. (4) Households in Osaka saved more electricity than those in Matsuyama, probably because the government call to save electricity was more forceful. - Highlights: •Energy efficient air conditioner purchases affect household power savings. •Additional air conditioner purchase led to significant energy savings. •Replacement units did not produce more savings than non-purchase. • “Electricity conservation directives” amount had a significant power-saving effect. •Altruistic households were more likely to cooperate with power-saving requests.

  2. The effect of daylight saving time options on electricity consumption of Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Karasu, Servet [Rize University, Rize Vocational School, 53100, Rize (Turkey)

    2010-09-15

    Most of the developed countries in the world use Daylight Saving Time (DST) as an energy conservation method. This study focuses on the effects of DST on electrical lighting in the buildings in Turkey. Turkey might adjust its daylight saving time to decrease energy consumption. For this purpose, five scenarios are considered and compared to status quo. The scenario with a 30-minute forward shift to single DST from April to October, stands out as the best solution to conserve electricity across the entire country. The results of the study show that maximum saving is obtained in this scenario by at least 0.7% on the consumption of lighting electricity. (author)

  3. Resuscitation therapy for traumatic brain injury-induced coma in rats: mechanisms of median nerve electrical stimulation

    Directory of Open Access Journals (Sweden)

    Zhen Feng

    2015-01-01

    Full Text Available In this study, rats were put into traumatic brain injury-induced coma and treated with median nerve electrical stimulation. We explored the wake-promoting effect, and possible mechanisms, of median nerve electrical stimulation. Electrical stimulation upregulated the expression levels of orexin-A and its receptor OX1R in the rat prefrontal cortex. Orexin-A expression gradually increased with increasing stimulation, while OX1R expression reached a peak at 12 hours and then decreased. In addition, after the OX1R antagonist, SB334867, was injected into the brain of rats after traumatic brain injury, fewer rats were restored to consciousness, and orexin-A and OXIR expression in the prefrontal cortex was downregulated. Our findings indicate that median nerve electrical stimulation induced an up-regulation of orexin-A and OX1R expression in the prefrontal cortex of traumatic brain injury-induced coma rats, which may be a potential mechanism involved in the wake-promoting effects of median nerve electrical stimulation.

  4. Saving, efficiency and management of electric sector demand

    International Nuclear Information System (INIS)

    Sanchez de Tembleque, L. J.

    2007-01-01

    Spanish economic model of development is based on energy consumption, and its main source is imported fossil fuels, which have some environmental and scarcity consequences in the mid term, among others. These problems could be reduced in two ways: economic activity reduction or energy efficiency improvement. In the presence of these possibilities, It may be desirable to bet for saving and energy efficiency, to maintain the economic development. This assignment analyzes the main available regulatory and social mechanisms to promote saving and energy efficiency in the power sector, like systems to internalize social costs in the electricity price, efficiency standards, and encourage the new saving culture. (Author) 15 refs

  5. Financing aspects of electricity saving's in Brazil

    International Nuclear Information System (INIS)

    Pacca, S.A.; Sauer, I.L.

    1996-01-01

    Programs regarding to energy saving in Brasil arised by the early 80's from the concern with oil products consumption. The situation has changed and electricity is growing in importance when energy conservation is discussed. Thus, the government, following examples from abroad, has been trying to overcome the barriers that obstruct a massive process evolution towards energy saving, since the potential is spread out in many society segments. One important issue is related to financing energy conservation. This paper attempts to analyze the utilities efforts allied to public and private banks investments towards energy conservation financing. (author)

  6. Measured energy savings and cost-effectiveness of conservation retrofits in commercial buildings

    International Nuclear Information System (INIS)

    Greely, K.M.; Harris, J.P.; Hatcher, A.M.

    1990-01-01

    In this study, the authors examine the measured savings and cost-effectiveness of 447 commercial retrofit projects in the US, Canada, and Europe, representing over 1,700 buildings. For these projects, they examine savings and cost-effectiveness by building type and retrofit strategy, savings from individual measures, peak electric demand savings, comparisons of measured vs. predicted savings, and the persistence of savings in the years following a retrofit. Median annual site energy savings amounted to 20 kBtu/ft 2 , or 18% of whole-building usage; median retrofit cost was $0.56/ft 2 (1988 $), the median payback time was 3.1 years, and the median cost of conserved energy was $3.10/site MBtu. When examined by retrofit strategy, they found that projects with only HVAC and/or lighting retrofits had median payback times of one to three years, while those affecting the building shell, either alone or in combination with other types of measures, had payback times of five or more years. Projects in which only maintenance practices were changed typically saved 12% of their pre-retrofit consumption, often using in-house labor. Their research suggests that, despite significant savings and short payback times for the majority of projects, optimum savings are often not being achieved, due to limited owner willingness to invest in all cost-effective measures, as well as to improper retrofit installation and/or maintenance. A comprehensive understanding of energy management as a process is needed, including both inspection and commissioning of installed retrofits and ongoing tracking of energy consumption as an indicator of operating problems

  7. Analysis on factors affecting household customers decision in using electricity at peak time and its correlation towards saving electricity

    Science.gov (United States)

    Pasasa, Linus; Marbun, Parlin; Mariza, Ita

    2015-09-01

    The purpose of this paper is to study and analyse the factors affecting customer decisions in using electricity at peak-load hours (between 17.00 to 22.00 WIB) and their behaviors towards electricity conservation in Indonesian household. The underlying rationale is to influence a reduction in energy consumption by stimulating energy saving behaviors, thereby reducing the impact of energy use on the environment. How is the correlation between the decisions in using electricity during peak load hours with the household customer's behavior towards saving electricity? The primary data is obtained by distributing questionnaires to customers of PT. PLN Jakarta Raya and Tangerang Distribution from Household segment. The data is analysed using the Structural Equation Model (SEM) and AMOS Software. The research is finding that all factors (Personal, Social, PLN Services, Psychological, and Cultural) are positively influence customer decision in using electricity at peak load hours. There is a correlation between the decisions in using electricity during peak load hours with the household customer's behavior towards saving electricity.

  8. Evaluation of the Electricity Saving Fund in Basel, Switzerland

    International Nuclear Information System (INIS)

    Iten, R.; Vettori, A.; Schmidt, N.; Vaterlaus, S.; Wild, J.

    2003-09-01

    This comprehensive report for the Swiss Federal Office of Energy (SFOE) presents the results of an evaluation made concerning the Electricity Saving Fund operated in Basel, Switzerland. The aims of the fund, which is based on the imposition of a steering levy on electricity consumption, are presented and discussed. It is noted that the political policies behind this promotional scheme differ greatly from those of other Swiss Cantons. This study examines the direct and indirect effects of the steering levy and the resulting bonus for energy-saving consumers and takes a look at possibilities for transferring the idea to other Swiss Cantons. Questions asked include the degree to which the aims were fulfilled, were negative side-effects noted, is the implementation efficient, can the know-how gained be transferred to other communities and Cantons and which general experience was gained in the application of steering levies. Details on the implementation of the Electricity Saving Bonus are presented and discussed. Results of a survey on the perception of the scheme both in the commercial and private sectors are discussed. Also, the results of evaluations made concerning the degree to which the scheme's aims were fulfilled and their usefulness from the national economics point of view are discussed. Suggestions for improvements are presented. The report is concluded with an a selection of annexes on the topics dealt with in the report

  9. Heat-electrical regeneration way to intensive energy saving in an electric arc furnaces

    Science.gov (United States)

    Kartavtcev, S.; Matveev, S.; Neshporenko, E.

    2018-03-01

    Energy saving in steel production is of great significance for its large economical scale of 1500 mil t/year and high-energy consumption. Steady trend of last years is an increase of steel production in electric arc furnaces (EAF) with a very high consumption of electricity up to 750 kWh/ton. The intention to reduce so much energy consumption they can reach by many ways. One of such way is a transforming heat energy of liquid steel to electricity and destine it to steel electric arc process. Under certain conditions, it may lead to “zero” consumption of electric power in the process. The development of these conditions leads to the formation of energy-efficient heat schemes, with a minimum electricity consumption from the external network.

  10. DSM Electricity Savings Potential in the Buildings Sector in APP Countries

    Energy Technology Data Exchange (ETDEWEB)

    McNeil, MIchael; Letschert, Virginie; Shen, Bo; Sathaye, Jayant; de la Ru du Can, Stephane

    2011-01-12

    The global economy has grown rapidly over the past decade with a commensurate growth in the demand for electricity services that has increased a country's vulnerability to energy supply disruptions. Increasing need of reliable and affordable electricity supply is a challenge which is before every Asia Pacific Partnership (APP) country. Collaboration between APP members has been extremely fruitful in identifying potential efficiency upgrades and implementing clean technology in the supply side of the power sector as well established the beginnings of collaboration. However, significantly more effort needs to be focused on demand side potential in each country. Demand side management or DSM in this case is a policy measure that promotes energy efficiency as an alternative to increasing electricity supply. It uses financial or other incentives to slow demand growth on condition that the incremental cost needed is less than the cost of increasing supply. Such DSM measures provide an alternative to building power supply capacity The type of financial incentives comprise of rebates (subsidies), tax exemptions, reduced interest loans, etc. Other approaches include the utilization of a cap and trade scheme to foster energy efficiency projects by creating a market where savings are valued. Under this scheme, greenhouse gas (GHG) emissions associated with the production of electricity are capped and electricity retailers are required to meet the target partially or entirely through energy efficiency activities. Implementation of DSM projects is very much in the early stages in several of the APP countries or localized to a regional part of the country. The purpose of this project is to review the different types of DSM programs experienced by APP countries and to estimate the overall future potential for cost-effective demand-side efficiency improvements in buildings sectors in the 7 APP countries through the year 2030. Overall, the savings potential is estimated to be

  11. Defining a standard metric for electricity savings

    International Nuclear Information System (INIS)

    Koomey, Jonathan; Akbari, Hashem; Blumstein, Carl; Brown, Marilyn; Brown, Richard; Calwell, Chris; Carter, Sheryl; Cavanagh, Ralph; Chang, Audrey; Claridge, David; Craig, Paul; Diamond, Rick; Eto, Joseph H; Fulkerson, William; Gadgil, Ashok; Geller, Howard; Goldemberg, Jose; Goldman, Chuck; Goldstein, David B; Greenberg, Steve

    2010-01-01

    The growing investment by governments and electric utilities in energy efficiency programs highlights the need for simple tools to help assess and explain the size of the potential resource. One technique that is commonly used in this effort is to characterize electricity savings in terms of avoided power plants, because it is easier for people to visualize a power plant than it is to understand an abstraction such as billions of kilowatt-hours. Unfortunately, there is no standardization around the characteristics of such power plants. In this letter we define parameters for a standard avoided power plant that have physical meaning and intuitive plausibility, for use in back-of-the-envelope calculations. For the prototypical plant this article settles on a 500 MW existing coal plant operating at a 70% capacity factor with 7% T and D losses. Displacing such a plant for one year would save 3 billion kWh/year at the meter and reduce emissions by 3 million metric tons of CO 2 per year. The proposed name for this metric is the Rosenfeld, in keeping with the tradition among scientists of naming units in honor of the person most responsible for the discovery and widespread adoption of the underlying scientific principle in question-Dr Arthur H Rosenfeld.

  12. Defining a standard metric for electricity savings

    Energy Technology Data Exchange (ETDEWEB)

    Koomey, Jonathan [Lawrence Berkeley National Laboratory and Stanford University, PO Box 20313, Oakland, CA 94620-0313 (United States); Akbari, Hashem; Blumstein, Carl; Brown, Marilyn; Brown, Richard; Calwell, Chris; Carter, Sheryl; Cavanagh, Ralph; Chang, Audrey; Claridge, David; Craig, Paul; Diamond, Rick; Eto, Joseph H; Fulkerson, William; Gadgil, Ashok; Geller, Howard; Goldemberg, Jose; Goldman, Chuck; Goldstein, David B; Greenberg, Steve, E-mail: JGKoomey@stanford.ed

    2010-01-15

    The growing investment by governments and electric utilities in energy efficiency programs highlights the need for simple tools to help assess and explain the size of the potential resource. One technique that is commonly used in this effort is to characterize electricity savings in terms of avoided power plants, because it is easier for people to visualize a power plant than it is to understand an abstraction such as billions of kilowatt-hours. Unfortunately, there is no standardization around the characteristics of such power plants. In this letter we define parameters for a standard avoided power plant that have physical meaning and intuitive plausibility, for use in back-of-the-envelope calculations. For the prototypical plant this article settles on a 500 MW existing coal plant operating at a 70% capacity factor with 7% T and D losses. Displacing such a plant for one year would save 3 billion kWh/year at the meter and reduce emissions by 3 million metric tons of CO{sub 2} per year. The proposed name for this metric is the Rosenfeld, in keeping with the tradition among scientists of naming units in honor of the person most responsible for the discovery and widespread adoption of the underlying scientific principle in question-Dr Arthur H Rosenfeld.

  13. Defining a Standard Metric for Electricity Savings

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Marilyn; Akbari, Hashem; Blumstein, Carl; Koomey, Jonathan; Brown, Richard; Calwell, Chris; Carter, Sheryl; Cavanagh, Ralph; Chang, Audrey; Claridge, David; Craig, Paul; Diamond, Rick; Eto, Joseph H.; Fulkerson, William; Gadgil, Ashok; Geller, Howard; Goldemberg, Jose; Goldman, Chuck; Goldstein, David B.; Greenberg, Steve; Hafemeister, David; Harris, Jeff; Harvey, Hal; Heitz, Eric; Hirst, Eric; Hummel, Holmes; Kammen, Dan; Kelly, Henry; Laitner, Skip; Levine, Mark; Lovins, Amory; Masters, Gil; McMahon, James E.; Meier, Alan; Messenger, Michael; Millhone, John; Mills, Evan; Nadel, Steve; Nordman, Bruce; Price, Lynn; Romm, Joe; Ross, Marc; Rufo, Michael; Sathaye, Jayant; Schipper, Lee; Schneider, Stephen H; Sweeney, James L; Verdict, Malcolm; Vorsatz, Diana; Wang, Devra; Weinberg, Carl; Wilk, Richard; Wilson, John; Worrell, Ernst

    2009-03-01

    The growing investment by governments and electric utilities in energy efficiency programs highlights the need for simple tools to help assess and explain the size of the potential resource. One technique that is commonly used in this effort is to characterize electricity savings in terms of avoided power plants, because it is easier for people to visualize a power plant than it is to understand an abstraction such as billions of kilowatt-hours. Unfortunately, there is no standardization around the characteristics of such power plants. In this letter we define parameters for a standard avoided power plant that have physical meaning and intuitive plausibility, for use in back-of-the-envelope calculations. For the prototypical plant this article settles on a 500 MW existing coal plant operating at a 70percent capacity factor with 7percent T&D losses. Displacing such a plant for one year would save 3 billion kW h per year at the meter and reduce emissions by 3 million metric tons of CO2 per year. The proposed name for this metric is the Rosenfeld, in keeping with the tradition among scientists of naming units in honor of the person most responsible for the discovery and widespread adoption of the underlying scientific principle in question--Dr. Arthur H. Rosenfeld.

  14. Tradable certificates for renewable electricity and energy savings

    International Nuclear Information System (INIS)

    Bertoldi, Paolo; Huld, Thomas

    2006-01-01

    Tradable green certificates (TGCs) schemes have been developed and tested in several European countries to foster market-driven penetration of renewables. These certificates guarantee that a specific volume of electricity is generated from renewable-energy source (RES). More recently certificates (tradable white certificates (TWCs)) for the electricity saved by demand-side energy-efficiency measures (EEMs) have been introduced in some European countries. Recent advances in information and communication technology have opened up new possibilities for improving energy efficiency and increasing utilization of RESs. Use of technological resources such as the Internet and smart metering can permit real-time issuing and trading of TGCs. These technologies could also permit issuing of TWC. This paper reviews current renewable TGC and TWCs schemes in Europe and describes the possibilities for combining them in an Internet-based system. In the proposed combined tradable certificate scheme, both RESs and demand-side EEMs could bid in real time through the Internet to meet a specific obligation. The energy savings from the demand-side measures would be equivalent to the same amount of green electricity production. The paper describes the needed common targets and obligations, the certificate trading rules and the possible monitoring protocol. In particular, the paper focuses on the TWCs verification issues, including the assessment of the baseline, as these poses additional problems for TWCs compared to TGCs. (author)

  15. A simple tool for estimating city-wide annual electrical energy savings from cooler surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Pomerantz, Melvin; Rosado, Pablo J.; Levinson, Ronnen

    2015-12-01

    We present a simple method to estimate the maximum possible electrical energy saving that might be achieved by increasing the albedo of surfaces in a large city. We restrict this to the “indirect effect”, the cooling of outside air that lessens the demand for air conditioning (AC). Given the power demand of the electric utilities and data about the city, we can use a single linear equation to estimate the maximum savings. For example, the result for an albedo change of 0.2 of pavements in a typical warm city in California, such as Sacramento, is that the saving is less than about 2 kWh per m2 per year. This may help decision makers choose which heat island mitigation techniques are economical from an energy-saving perspective.

  16. Mobile recommender application for promoting electricity saving among Iraqis

    Science.gov (United States)

    Sabri, Manhal Isam; Hussain, Azham

    2017-10-01

    Mobile utilization has rapidly expanded due to its feasibility in executing different applications that can be used in solving everyday problems. Common issues in daily life include electricity saving. In Iraq, the Ministry of Power seriously faces such issue. This is because most households have lack access to information regarding to sufficient power consumption, as well as applications that educate about such saving. Therefore, this study aims at developing a mobile application for Iraqi to help them understand the basis for reducing electricity consumption based on the meter data supplied by the users for square meter along with the active devices and period of usage. The proposed mobile application was evaluated by 50 households from the perspective of ease of use, usefulness, ease of learning, and satisfaction. The obtained result showed that majority of the participants found the application to be ease to use, useful, easy to learn, and were satisfied with its functionalities. The study findings provide some insights about the importance of using mobile application for promoting households in Iraq to manage their power consumption behavior.

  17. The impact of daylight saving time on electricity consumption: Evidence from southern Norway and Sweden

    Energy Technology Data Exchange (ETDEWEB)

    Mirza, Faisal Mehmood, E-mail: faisal.mirza@umb.no [Department of Economics and Resource Management, Norwegian University of Life Sciences (UMB), P.O. Box 5003, 1432 As (Norway); Bergland, Olvar, E-mail: olvar.bergland@umb.no [Department of Economics and Resource Management, Norwegian University of Life Sciences (UMB), P.O. Box 5003, 1432 As (Norway)

    2011-06-15

    This paper examines the impact of daylight saving time (DST) on electricity consumption in southern Norway and Sweden. As DST was implemented in both the countries in 1980, we do not have a clear counterfactual in the form of a control period to identify the impact of DST directly with before and after or with and without analysis. This problem in the study is resolved by using 'equivalent day normalization technique' to identify the impact of DST. The difference-in-difference (DID) average treatment effects model suggests an annual reduction of at least 1.0 percent in electricity consumption for both Norway and Sweden due to DST. The average annual electricity consumption reduction corresponding to DST effects equals 519 and 882 GWh for southern Norway and Sweden, resulting in an annual financial saving of 16.1 million Euros and 30.1 million Euros, respectively. The distribution of treatment effects across different hours of the day indicates a small but significant reduction in electricity consumption during the morning and a steep decline during the evening hours in both countries. - Highlights: > We assess the impact of DST on electricity consumption in southern Norway and Sweden. > DST reduces electricity consumption by 1.3 percent in both countries. > The impact is smaller during the morning hours but larger during evening hours. > Respective annual financial savings equal Euro 16.1 and 30.1 million for Norway and Sweden. > Average annual electricity savings equal 519 and 882 GWh for two countries, respectively.

  18. The impact of daylight saving time on electricity consumption: Evidence from southern Norway and Sweden

    International Nuclear Information System (INIS)

    Mirza, Faisal Mehmood; Bergland, Olvar

    2011-01-01

    This paper examines the impact of daylight saving time (DST) on electricity consumption in southern Norway and Sweden. As DST was implemented in both the countries in 1980, we do not have a clear counterfactual in the form of a control period to identify the impact of DST directly with before and after or with and without analysis. This problem in the study is resolved by using 'equivalent day normalization technique' to identify the impact of DST. The difference-in-difference (DID) average treatment effects model suggests an annual reduction of at least 1.0 percent in electricity consumption for both Norway and Sweden due to DST. The average annual electricity consumption reduction corresponding to DST effects equals 519 and 882 GWh for southern Norway and Sweden, resulting in an annual financial saving of 16.1 million Euros and 30.1 million Euros, respectively. The distribution of treatment effects across different hours of the day indicates a small but significant reduction in electricity consumption during the morning and a steep decline during the evening hours in both countries. - Highlights: → We assess the impact of DST on electricity consumption in southern Norway and Sweden. → DST reduces electricity consumption by 1.3 percent in both countries. → The impact is smaller during the morning hours but larger during evening hours. → Respective annual financial savings equal Euro 16.1 and 30.1 million for Norway and Sweden. → Average annual electricity savings equal 519 and 882 GWh for two countries, respectively.

  19. Saving energy and protecting environment of electric vehicles

    Science.gov (United States)

    Yuan, Lina; Chen, Huajun; Gong, Jing

    2017-05-01

    With the concept of low carbon economy, saving energy, and protecting environment spread, the development of the electric promotes the research pace of wireless charging electronic vehicles, which will become the best choice of energy supply in the future. To generalize and exploit the corresponding alternative fuels and the research and development, and promotion of electric vehicles, becomes the effective means to directly reduce the consumption of fuel, effectively relieves the problem of nervous energy and environmental pollution, and really conforms to the requirements of the national strategy of sustainable development in China. This paper introduces the status of electronic cars and wireless charging, expounds the principle of wireless charging, and concludes the full text.

  20. Net fossil energy savings for alternative mixes in various electric supply systems

    International Nuclear Information System (INIS)

    Essam, P.; Stocks, K.J.

    1978-11-01

    The actual and projected electric power station building programs of several countries and regions have been examined to determine what effect the introduction of nuclear power has on fossil fuel usage by the electricity system. It was found that (1) nuclear power leads directly to savings in fossil fuel usage, a larger nuclear component leading to larger savings; (2) individual nuclear stations rapidly wipe out the energy 'debt' incurred during building; and (3) the relatively short periods of consolidation in the early stages of a nation's building program usually prevent the nuclear component from going into energy 'debt'. Assessments of the energy requirements to build and run various types of power station have been made from the available literature

  1. Providing feedback as a means to empower householders to save electricity: A social cognitive approach

    DEFF Research Database (Denmark)

    Thøgersen, John; Grønhøj, Alice

    Studies show that the electricity consumption in private households could be substantially reduced (5 - 25%) without the loss of comfort by using best practice technology and care (Birch & Krogboe A/S, 2004). A number of reasons for the squandering of electricity have been pointed out: the force...... of habit, lack of attention towards the issue, lack of motivation due to an unfavorable cost/benefit ratio, uncertainty about the environmental consequences of the squandering of electricity and about the effects of possible conservation efforts. Based on Bandura's (1986) social cognitive theory......, this paper outlines a conceptual framework for understanding private consumers' (lack of) energy saving effort. The framework is tested based on a sample of Danish private electricity consumers and it is concluded that the impediments that now makes electricity saving difficult are a key action point...

  2. Electricity-cost savings obtained by means of nuclear plant life extension

    International Nuclear Information System (INIS)

    Forest, L.; Fletcher, T.; DuCharme, A.; Harrison, D.L.

    1987-01-01

    This study examines savings caused by nuclear-plant life extension (NUPLEX) and describes the effects of changes in assumptions on costs and technology using an approach simpler than the large economic-model simulations used in other reports. Under the simplified approach, we estimate savings at the broad national level by comparing projected costs/kWh for the typical NUPLEX plant with those for new coal-fired plants, which seem the most likely alternative in most regions. While ignoring some complications handled by the large, regionally disaggregated econometric models, the approach used in this study has advantages in sensitivity analyses. It reveals relationships between savings and basic assumptions on costs and technology in a more transparent way than in large-model simulations. We find that, absent major technological breakthroughs for present generating options, NUPLEX saves consumers money on their electric bills under most plausible economic scenarios. Using mid-range assumptions, we find that NUPLEX saves consumers a total of about dollar 180 billion spread over the period 2010-50. Under optimistic assumptions, the savings swell to over dollar 900 billion. Under extremely pessimistic assumptions, the savings actually turn negative. This wide range of estimates largely reflects the uncertainty in cost projections. Within plausible limits, higher- or lower-than-expected load growth does not affect the savings estimates. The NUPLEX construction costs stand out as the most critical unknown. If they turn out to be 50% (dollar 500 billion) above the baseline estimate savings would fall by almost 60% (dollar 105 billion). A 50% rise in nuclear fuel costs would drop baseline savings by almost 22%. A 50% increase in nuclear-plant operations-and-maintenance costs, would cut baseline savings by about 36%. These sensitivities highlight the need for continued monitoring of economic developments

  3. Integration scenarios of Demand Response into electricity markets: Load shifting, financial savings and policy implications

    International Nuclear Information System (INIS)

    Feuerriegel, Stefan; Neumann, Dirk

    2016-01-01

    Demand Response allows for the management of demand side resources in real-time; i.e. shifting electricity demand according to fluctuating supply. When integrated into electricity markets, Demand Response can be used for load shifting and as a replacement for both control reserve and balancing energy. These three usage scenarios are compared based on historic German data from 2011 to determine that load shifting provides the highest benefit: its annual financial savings accumulate to €3.110 M for both households and the service sector. This equals to relative savings of 2.83% compared to a scenario without load shifting. To improve Demand Response integration, the proposed model suggests policy implications: reducing bid sizes, delivery periods and the time-lag between market transactions and delivery dates in electricity markets. - Highlights: •Comparison of 3 scenarios to integrate Demand Response into electricity markets. •These are: optimize procurement, offer as control reserve, avoid balancing energy. •Ex post simulation to quantify financial impact and policy implications. •Highest savings from load shifting with a cost reduction of 3%. •Model suggests reducing bid sizes, delivery periods and time lags as policy issues.

  4. The Impact of Minimum Energy Performance Standards (MEPS) Regulation on Electricity Saving in Malaysia

    Science.gov (United States)

    Fatihah Salleh, Siti; Eqwan Roslan, Mohd; Isa, Aishah Mohd; Faizal Basri Nair, Mohd; Syafiqah Salleh, Siti

    2018-03-01

    One of Malaysia’s key strategies to promote efficient energy use in the country is to implement the minimum energy performance standards (MEPS) through the Electricity Regulations (Amendment) 2013. Five selected electrical appliances (refrigerator, air conditioner, television, domestic fans and lamp fittings) must comply with MEPS requirement in order to be sold in Malaysian market. Manufacturers, importers or distributors are issued Certificate of Approval (COA) if products are MEPS-compliant. In 2015, 1,215 COAs were issued but the number of MEPS products in the market is unknown. This work collects sales data from major manufacturers to estimate the annual sales of MEPS appliances and the cumulative electricity consumption and electricity saving. It was found that most products sold have 3-star rating and above. By year 2015, total cumulative electricity savings gained from MEPS implementation is 3,645 GWh, with air conditioner being the highest contributor (30%). In the future, it is recommended that more MEPS products and related incentives be introduced to further improve efficiency of energy use in Malaysia.

  5. Evaluation of the Electricity Saving Fund in Basel, Switzerland; Evaluation des Stromsparfonds Basel

    Energy Technology Data Exchange (ETDEWEB)

    Iten, R; Vettori, A; Schmidt, N [Infras, Zuerich (Switzerland); Vaterlaus, S; Wild, J [Plaut (Schweiz) Consulting AG, Bern (Switzerland)

    2003-09-15

    This comprehensive report for the Swiss Federal Office of Energy (SFOE) presents the results of an evaluation made concerning the Electricity Saving Fund operated in Basel, Switzerland. The aims of the fund, which is based on the imposition of a steering levy on electricity consumption, are presented and discussed. It is noted that the political policies behind this promotional scheme differ greatly from those of other Swiss Cantons. This study examines the direct and indirect effects of the steering levy and the resulting bonus for energy-saving consumers and takes a look at possibilities for transferring the idea to other Swiss Cantons. Questions asked include the degree to which the aims were fulfilled, were negative side-effects noted, is the implementation efficient, can the know-how gained be transferred to other communities and Cantons and which general experience was gained in the application of steering levies. Details on the implementation of the Electricity Saving Bonus are presented and discussed. Results of a survey on the perception of the scheme both in the commercial and private sectors are discussed. Also, the results of evaluations made concerning the degree to which the scheme's aims were fulfilled and their usefulness from the national economics point of view are discussed. Suggestions for improvements are presented. The report is concluded with an a selection of annexes on the topics dealt with in the report

  6. Evaluation of the Electricity Saving Fund in Basel, Switzerland; Evaluation des Stromsparfonds Basel

    Energy Technology Data Exchange (ETDEWEB)

    Iten, R.; Vettori, A.; Schmidt, N. [Infras, Zuerich (Switzerland); Vaterlaus, S.; Wild, J. [Plaut (Schweiz) Consulting AG, Bern (Switzerland)

    2003-09-15

    This comprehensive report for the Swiss Federal Office of Energy (SFOE) presents the results of an evaluation made concerning the Electricity Saving Fund operated in Basel, Switzerland. The aims of the fund, which is based on the imposition of a steering levy on electricity consumption, are presented and discussed. It is noted that the political policies behind this promotional scheme differ greatly from those of other Swiss Cantons. This study examines the direct and indirect effects of the steering levy and the resulting bonus for energy-saving consumers and takes a look at possibilities for transferring the idea to other Swiss Cantons. Questions asked include the degree to which the aims were fulfilled, were negative side-effects noted, is the implementation efficient, can the know-how gained be transferred to other communities and Cantons and which general experience was gained in the application of steering levies. Details on the implementation of the Electricity Saving Bonus are presented and discussed. Results of a survey on the perception of the scheme both in the commercial and private sectors are discussed. Also, the results of evaluations made concerning the degree to which the scheme's aims were fulfilled and their usefulness from the national economics point of view are discussed. Suggestions for improvements are presented. The report is concluded with an a selection of annexes on the topics dealt with in the report

  7. Estimating the cost of saving electricity through U.S. utility customer-funded energy efficiency programs

    International Nuclear Information System (INIS)

    Hoffman, Ian M.; Goldman, Charles A.; Rybka, Gregory; Leventis, Greg; Schwartz, Lisa; Sanstad, Alan H.; Schiller, Steven

    2017-01-01

    The program administrator and total cost of saved energy allow comparison of the cost of efficiency across utilities, states, and program types, and can identify potential performance improvements. Comparing program administrator cost with the total cost of saved energy can indicate the degree to which programs leverage investment by participants. Based on reported total costs and savings information for U.S. utility efficiency programs from 2009 to 2013, we estimate the savings-weighted average total cost of saved electricity across 20 states at $0.046 per kilowatt-hour (kW h), comparing favorably with energy supply costs and retail rates. Programs targeted on the residential market averaged $0.030 per kW h compared to $0.053 per kW h for non-residential programs. Lighting programs, with an average total cost of $0.018 per kW h, drove lower savings costs in the residential market. We provide estimates for the most common program types and find that program administrators and participants on average are splitting the costs of efficiency in half. More consistent, standardized and complete reporting on efficiency programs is needed. Differing definitions and quantification of costs, savings and savings lifetimes pose challenges for comparing program results. Reducing these uncertainties could increase confidence in efficiency as a resource among planners and policymakers. - Highlights: • The cost of saved energy allows comparisons among energy resource investments. • Findings from the most expansive collection yet of total energy efficiency program costs. • The weighted average total cost of saved electricity was $0.046 for 20 states in 2009–2013. • Averages in the residential and non-residential sectors were $0.030 and $0.053 per kW h, respectively. • Results strongly indicate need for more consistent, reliable and complete reporting on efficiency programs.

  8. Ultra high benefits system for electric energy saving and management of lighting energy in buildings

    International Nuclear Information System (INIS)

    Fathabadi, Hassan

    2014-01-01

    Highlights: • Presenting a novel multi channel smart system to manage lighting energy in buildings. • Saving considerable electric energy which is converted to lighting in buildings. • Providing desired constant and adjustable luminance for each location in buildings. • Capability of working with all AC electric power sources. • To automatically control and manage lighting energy in buildings. - Abstract: This paper presents a smart system, including a multi channel dimmer and a central process unit (CPU) together with an exact multi channel feedback mechanism, which automatically regulates and manages lighting in buildings. Based on a multi channel luminance feedback, a high benefits technique is utilized to convert the electric energy to lighting energy. Saving a lot of the electric energy which should be converted to lighting energy in buildings, managing the lighting energy in buildings, providing desired constant and adjustable luminance for each room (location), and the capability of working with all AC electric power sources regardless of frequency and voltage amplitude are some advantages of using the proposed system and technique, thus it will be widely used in buildings. An experimental prototype of the proposed smart system has been constructed to validate the theoretical results and to carry out the experimental tests. Experimental results earned by utilizing the proposed smart system in a sample building are presented to prove the benefits of using the system. The experimental results explicitly show a considerable electric energy saving (about 27%) in the sample building while the proposed system has provided desired constant and adjustable luminance for each location of the building

  9. Understanding usage patterns of electric kettle and energy saving potential

    International Nuclear Information System (INIS)

    Murray, D.M.; Liao, J.; Stankovic, L.; Stankovic, V.

    2016-01-01

    Highlights: • Time-of-use analysis to motivate kettle usage and consumption prediction. • Identification of households whose kettle usage and consumption is outside the norm. • Mathematical model to estimate water volume from consumed power measurements only. • Quantification of energy savings if a household uses its kettle more efficiently. • Kettle usage and demand prediction using an Adaptive Neuro Fuzzy Inference System. - Abstract: The availability of smart metering and smart appliances enables detecting and characterising appliance use in a household, quantifying energy savings through efficient appliance use and predicting appliance-specific demand from load measurements is possible. With growing electric kettle ownership and usage, lack of any efficiency labelling guidelines for the kettle, slow technological progress in improving kettle efficiency relative to other domestic appliances, and current consumer attitudes, urgent investigation into consumer kettle usage patterns is warranted. From an efficiency point of view, little can be done about the kettle, which is more efficient than other methods of heating water such as the stove top kettle. However, since a majority households use the kettle inefficiently by overfilling, in order to meet energy targets, it is imperative to quantify inefficient usage and predict demand. For the purposes of scalability, we propose tools that depend only on load measurement data for quantifying and visualising kettle usage and energy consumption, assessing energy wastage through overfilling via our proposed electric kettle model, and predicting kettle-specific demand, from which we can estimate potential energy savings in a household and across a housing stock. This is demonstrated using data from a longitudinal study across a sample of 14 UK households for a two-year period.

  10. The impact of rate design and net metering on the bill savings from distributed PV for residential customers in California

    International Nuclear Information System (INIS)

    Darghouth, Naim R.; Barbose, Galen; Wiser, Ryan

    2011-01-01

    Net metering has become a widespread mechanism in the U.S. for supporting customer adoption of distributed photovoltaics (PV), but has faced challenges as PV installations grow to a larger share of generation in a number of states. This paper examines the value of the bill savings that customers receive under net metering, and the associated role of retail rate design, based on a sample of approximately two hundred residential customers of California's two largest electric utilities. We find that the bill savings per kWh of PV electricity generated varies by more than a factor of four across the customers in the sample, which is largely attributable to the inclining block structure of the utilities' residential retail rates. We also compare the bill savings under net metering to that received under three potential alternative compensation mechanisms, based on California's Market Price Referent (MPR). We find that net metering provides significantly greater bill savings than a full MPR-based feed-in tariff, but only modestly greater savings than alternative mechanisms under which hourly or monthly net excess generation is compensated at the MPR rate. - Highlights: → We examine the value of bill savings under net metering to PV owners in California. → Bill savings per kWh of PV generation varies by a factor of four with net metering. The variation is attributable to rate design, the unique inclining block structure. → The median value of bill savings is reduced by 40-67% with MPR feed-in tariff. → The median value of bill savings is reduced by 6-12% with hourly netting.

  11. Projected electricity savings from implementing minimum energy efficiency standard for household refrigerators in Malaysia

    International Nuclear Information System (INIS)

    Mahlia, T.M.I.; Masjuki, H.H.; Saidur, R.; Choudhury, I.A.; NoorLeha, A.R.

    2003-01-01

    The Malaysian economy has grown rapidly in the last two decades. This growth has increased the ownership of household electrical appliances, especially refrigerator-freezers. Almost every house in Malaysia owns a refrigerator-freezer. The Malaysia Energy Center considered implementing a minimum energy efficiency standard for household refrigerator-freezers sometime in the coming year. This paper attempts to predict the amount of energy savings in the residential sector by implementing a minimum energy efficiency standard for household refrigerator-freezers. The calculations are based on the growth of refrigerator-freezer ownership data in Malaysian households. By implementing the programs in 2004, about 8722 GWh will be saved in the year 2013. Therefore, efficiency improvement of this appliance will provide a significant impact in future electricity consumption in Malaysia

  12. How EPRI [Electric Power Research Institute] helps utilities save money

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    A number of case studies are presented which illustrate how the work of the Electric Power Research Institute in the USA has enabled nuclear utilities to save money. The areas covered by the examples are: steam generator tube repair; streamlining of reliability centred maintenance; cost effective instrumentation and control maintenance; reducing the frequency of instrument calibration; optimising the engineering change process; detecting and reducing fuel failure; extending the qualified life of equipment. (U.K.)

  13. Microscopic Driving Parameters-Based Energy-Saving Effect Analysis under Different Electric Vehicle Penetration

    Directory of Open Access Journals (Sweden)

    Enjian Yao

    2013-01-01

    Full Text Available Due to the rapid motorization over the recent years, China's transportation sector has been facing an increasing environmental pressure. Compared with gasoline vehicle (GV, electric vehicle (EV is expected to play an important role in the mitigation of CO2 and other pollution emissions, and urban air quality improvement, for its zero emission during use and higher energy efficiency. This paper aims to estimate the energy saving efficiency of EV, especially under different EV penetration and road traffic conditions. First, based on the emission and electricity consumption data collected by a light-duty EV and a light duty GV, a set of electricity consumption rate models and gasoline consumption rate models are established. Then, according to the conversion formula of coal equivalent, these models are transformed into coal equivalent consumption models, which make gasoline consumption and electricity consumption comparable. Finally, the relationship between the EV penetration and the reduction of energy consumption is explored based on the simulation undertaken on the North Second Ring Road in Beijing. The results show that the coal equivalent consumption will decrease by about 5% with the increases of EV penetration by 10% and the maximum energy-saving effect can be achieved when the traffic volume is about 4000 pcu/h.

  14. Monetary or environmental appeals for saving electricity? –Potentials for spillover on low carbon policy acceptability

    International Nuclear Information System (INIS)

    Steinhorst, Julia; Matthies, Ellen

    2016-01-01

    The acceptability of low carbon policies is an important precondition for energy system transitions, such as the German Energiewende. This long-term experimental study examines the potential for behavioural spillover on the acceptability of low carbon policies, caused by a framed intervention to promote electricity saving behaviour. Clients of a German energy provider were randomly assigned to continuously receive electricity saving tips with either monetary framing (saving potential in €) or environmental framing (saving potential in CO_2). The control group did not receive any information. In two follow-up surveys, four (N=333) and nine months (N=258) later, participants rated the acceptability of several low carbon policies. A pre-survey assessed the personal ecological norm for saving electricity. Participants with strong personal ecological norms reported generally higher policy acceptability. After environmental framing they also indicated higher acceptability compared to the monetary framing or control group. These results indicate that information campaigns should be designed carefully in order to promote positive spillover effects. Environmental framing of private-sphere behaviour can increase the disposition for further pro-environmental behaviour in the public sphere, e.g. policy acceptability. When appealing to monetary benefits in pro-environmental behaviour, there is a risk of inhibiting positive spillover effects. - Highlights: •Policy acceptability may be influenced by type of framing and individual factors. •We examined long-term spillover effects in association with type of framing. •Framing (environmental vs. monetary) interacts with personal ecological norms. •For strong personal ecological norms, environmental framing increases acceptability. •Also, strong personal ecological norms increase low carbon policy acceptability.

  15. Establishment of windows-based load management system for electricity cost savings in competitive electricity markets

    International Nuclear Information System (INIS)

    Chung, K.H.; Kim, B.H.; Hur, D.

    2007-01-01

    For electricity markets to function in a truly competitive and efficient manner, it is not enough to focus solely on improving the efficiencies of power supply. To recognize price-responsive load as a reliability resource, the customer must be provided with price signals and an instrument to respond to these signals, preferably automatically. This paper attempts to develop the Windows-based load management system in competitive electricity markets, allowing the user to monitor the current energy consumption or billing information, to analyze the historical data, and to implement the consumption strategy for cost savings with nine possible scenarios adopted. Finally, this modeling framework will serve as a template containing the basic concepts that any load management system should address. (author)

  16. Energy Savings in a Market Economy

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen

    1998-01-01

    The paper outlines the concept of energy savings as opposed to energy efficency. Afterwards are described briefly the up and down role of energy savings in recent Danish energy policy. It discusses the failure of leaving electricity savings and Integrated Resource Planning to the electricity...

  17. The devil is in the details: Household electricity saving behavior and the role of information

    International Nuclear Information System (INIS)

    Ek, Kristina; Soederholm, Patrik

    2010-01-01

    The purpose of this paper is to analyze Swedish households' willingness to increase their daily efforts to save electricity. The analysis builds on a broad theoretical framework, which embraces both economic and norm-based motivations in explaining household behavior. The paper pays particular attention to the role of information about the availability of different behavioral changes that can be undertaken at the household level. The empirical results are based on a postal survey that was sent out to 1200 Swedish households, and the econometric analysis is carried out within a so-called ordered probit framework. Our results indicate that costs, environmental attitudes and social interactions are all important determinants of electricity saving activities within Swedish households. We tested the hypothesis that information about available savings measures that is presented in a more concrete and specific way is more likely to affect (stated) behavior than is more general information, and the data collected support this notion. The paper ends by discussing some implications of these results for the design of future informative policy measures in the energy-efficiency field.

  18. The devil is in the details. Household electricity saving behavior and the role of information

    Energy Technology Data Exchange (ETDEWEB)

    Ek, Kristina; Soederholm, Patrik [Economics Unit, Luleaa University of Technology, 971 87 Luleaa (Sweden)

    2010-03-15

    The purpose of this paper is to analyze Swedish households' willingness to increase their daily efforts to save electricity. The analysis builds on a broad theoretical framework, which embraces both economic and norm-based motivations in explaining household behavior. The paper pays particular attention to the role of information about the availability of different behavioral changes that can be undertaken at the household level. The empirical results are based on a postal survey that was sent out to 1200 Swedish households, and the econometric analysis is carried out within a so-called ordered probit framework. Our results indicate that costs, environmental attitudes and social interactions are all important determinants of electricity saving activities within Swedish households. We tested the hypothesis that information about available savings measures that is presented in a more concrete and specific way is more likely to affect (stated) behavior than is more general information, and the data collected support this notion. The paper ends by discussing some implications of these results for the design of future informative policy measures in the energy-efficiency field. (author)

  19. The devil is in the details: Household electricity saving behavior and the role of information

    Energy Technology Data Exchange (ETDEWEB)

    Ek, Kristina, E-mail: kristina.ek@ltu.s [Economics Unit, Lulea University of Technology, 971 87 Lulea (Sweden); Soederholm, Patrik, E-mail: Patrik.Soderholm@ltu.s [Economics Unit, Lulea University of Technology, 971 87 Lulea (Sweden)

    2010-03-15

    The purpose of this paper is to analyze Swedish households' willingness to increase their daily efforts to save electricity. The analysis builds on a broad theoretical framework, which embraces both economic and norm-based motivations in explaining household behavior. The paper pays particular attention to the role of information about the availability of different behavioral changes that can be undertaken at the household level. The empirical results are based on a postal survey that was sent out to 1200 Swedish households, and the econometric analysis is carried out within a so-called ordered probit framework. Our results indicate that costs, environmental attitudes and social interactions are all important determinants of electricity saving activities within Swedish households. We tested the hypothesis that information about available savings measures that is presented in a more concrete and specific way is more likely to affect (stated) behavior than is more general information, and the data collected support this notion. The paper ends by discussing some implications of these results for the design of future informative policy measures in the energy-efficiency field.

  20. The impact of the daylight saving time on electricity consumption-A case study from Jordan

    International Nuclear Information System (INIS)

    Awad Momani, Mohammad; Yatim, Baharudin; Ali, Mohd Alauddin Mohd

    2009-01-01

    The paper examines the impact of daylight saving time (DST) on electricity consumption in Jordan. Two types of analysis were done: the first analysis examines the impact of DST on the lighting loads based on a survey study made for residential and commercial sectors. The second examines the impact of DST on the over all electricity generation through analyzing the daily load curves (DLCs) before and after the DST onset and removal in 2000 and 2007. The results show that the application of DST during the year 2000 saves the electricity used for illumination by -0.73% but it increases the overall generation at the onset and removal of DST by 0.5% and 1.4% due to increase in the heating and cooling loads. The analysis of DLCs during the year 2007 shows similar effects as in the year 2000 except during the early morning period at the DST onset where DST decreases the demand during this time. The analysis shows that DST decreases the electricity demand at DST onset by 0.2% and increases it at DST removal by 0.3%. A possible decrease in the electricity consumption may take place if the DST is implemented from April to end of August.

  1. Feasibility study on combined use of residential SOFC cogeneration system and plug-in hybrid electric vehicle from energy-saving viewpoint

    International Nuclear Information System (INIS)

    Wakui, Tetsuya; Wada, Naohiro; Yokoyama, Ryohei

    2012-01-01

    Highlights: ► Optimal operational planning for combined use of SOFC-CGS and PHEV is conducted. ► Charging PHEV with SOFC-CGS increases electric capacity factor of SOFC-CGS. ► Energy-saving effect of combined use is higher than that of their separate use. ► Combined use provides energy savings in both residential and transport sectors. - Abstract: The energy-saving effect of a combined use of a residential solid oxide fuel cell cogeneration system (SOFC-CGS) that adopts a continuous operation, and a plug-in hybrid electric vehicle (PHEV) is discussed by optimal operational planning based on mixed-integer linear programming. This combined use aims to increase the electric capacity factor of the SOFC-CGS by charging the PHEV using the SOFC-CGS electric power output late at night, and targets the application in regions where the reverse power flow from residential cogeneration systems to commercial electric power systems is not permitted, like in Japan. The optimal operation patterns of the combined use of 0.7-kWe SOFC-CGS and PHEV for a simulated energy demand with a sampling time of 1 h and various daily running distances of the PHEV show that this combined use increases the electric capacity factor of the SOFC-CGS and saves more energy in comparison with their separate use in which the SOFC-CGS is used but the PHEV is charged only with purchased electric power. Furthermore, it is found that at the PHEV daily running distance of 12 km/d, the reduction rate of the annual primary energy consumption for this combined use increases by up to 3.7 percentage points relative to their separate use. Consequently, this feasibility study reveals that the combined use of the SOFC-CGS and PHEV provides the synergistic effect on energy savings in the residential and transport sectors. For the practical use, simulation scenarios considering the energy demand fluctuations with short periods and real-time pricing of the purchased electric power must be considered as future

  2. Riding the Electricity Market as an Energy Management Strategy: Savings from Real-Time Pricing

    Energy Technology Data Exchange (ETDEWEB)

    Chiles, Thomas [U.S. General Services Administration, Washington, D.C. (United States); Shutika, Kenneth [U.S. General Services Administration, Washington, D.C. (United States); Coleman, Philip [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2018-03-13

    Dynamic pricing of electricity, in which retail prices facing customers are responsive to changes in the underlying wholesale markets, represents a step towards economic efficiency in that customers get exposed to some or all of the costs facing wholesale market players. But what do customers who opt for this greater exposure – available in the roughly 15 “de-regulated” states, as well as, to some extent, from some regulated utilities – get in return for their risks? The U.S. General Services Administration (GSA) took a retrospective eight-year look at what the savings would have been had they let the loads for which they purchase electricity in the Washington, DC area buy electricity on the real-time pricing (RTP) market – the dynamic pricing option with the highest risk – as opposed to the strategy they chose in actuality, which was fixing flat prices with 3rd-party providers. We found that opting for RTP for the eight years of the study (2005 through 2012) would have resulted in 17% savings, or almost a quarter of a billion dollars, relative to GSA’s actual prices from the 3rd-party suppliers. This is particularly astonishing given that GSA appeared to have timed the market well during the study period, consistently beating the standard offer products provided by the distribution utilities. The issue of budgetary predictability poses an obstacle for customers (especially government ones) considering RTP and, to a lesser extent, other dynamic pricing options. Indeed, GSA would have lost money with RTP in two of the eight years, one of them substantially. But the magnitude of the savings is indisputably compelling and, even if it may be somewhat aberrational due to high congestion in the DC market, begs consideration by large electricity users currently paying to “lock in” fixed flat prices.

  3. Joule-Thief Circuit Performance for Electricity Energy Saving of Emergency Lamps

    Science.gov (United States)

    Nuryanto Budisusila, Eka; Arifin, Bustanul

    2017-04-01

    The alternative energy such as battery as power source is required as energy source failures. The other need is outdoor lighting. The electrical power source is expected to be a power saving, optimum and has long life operating. The Joule-Thief circuit is one of solution method for energy saving by using raised electromagnetic force on cored coil when there is back-current. This circuit has a transistor operated as a switch to cut voltage and current flowing along the coils. The present of current causing magnetic induction and generates energy. Experimental prototype was designed by using battery 1.5V to activate Light Emitting Diode or LED as load. The LED was connected in parallel or serial circuit configuration. The result show that the joule-thief circuit able to supply LED circuits up to 40 LEDs.

  4. Evaluation of Savings in Energy-Efficient Public Housing in the Pacific Northwest

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-10-01

    This report presents the results of an energy performance and cost-effectiveness analysis. The Salishan phase 7 and demonstration homes were compared to Salishan phase 6 homes built to 2006 Washington State Energy Code specifications 2. Predicted annual energy savings (over Salishan phase 6) was 19% for Salishan phase 7, and between 19-24% for the demonstration homes (depending on ventilation strategy). Approximately two-thirds of the savings are attributable to the DHP. Working with the electric utility provider, Tacoma Public Utilities, researchers conducted a billing analysis for Salishan phase 7. Median energy use for the development is 11,000 kWh; annual energy costs are $780, with a fair amount of variation dependent on size of home. Preliminary analysis of savings between Salishan 7 and previous phases (4 through 6) suggest savings of between 20 and 30 percent. A more comprehensive comparison between Salishan 7 and previous phases will take place in year two of this project.

  5. Evaluation of Savings in Energy-Efficient Public Housing in the Pacific Northwest

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, A. [Washington State Univ. Extension Energy Office, Cocoa, FL (United States); Lubliner, M. [Washington State Univ. Extension Energy Office, Cocoa, FL (United States); Howard, L. [Washington State Univ. Extension Energy Office, Cocoa, FL (United States); Kunkle, R. [Washington State Univ. Extension Energy Office, Cocoa, FL (United States); Martin, E. [Washington State Univ. Extension Energy Office, Cocoa, FL (United States)

    2013-10-01

    This report presents the results of an energy performance and cost-effectiveness analysis. The Salishan phase 7 and demonstration homes were compared to Salishan phase 6 homes built to 2006 Washington State Energy Code specifications 2. Predicted annual energy savings (over Salishan phase 6) was 19% for Salishan phase 7, and between 19-24% for the demonstration homes (depending on ventilationstrategy). Approximately two-thirds of the savings are attributable to the DHP. Working with the electric utility provider, Tacoma Public Utilities, researchers conducted a billing analysis for Salishan phase 7. Median energy use for the development is 11,000 kWh; annual energy costs are $780, with a fair amount of variation dependent on size of home. Preliminary analysis of savings betweenSalishan 7 and previous phases (4 through 6) suggest savings of between 20 and 30 percent. A more comprehensive comparison between Salishan 7 and previous phases will take place in year two of this project.

  6. Electricity consumption and energy savings potential of video game consoles in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Hittinger, E.; Mullins, K.A.; Azevedo, I.L. [Department of Engineering and Public Policy, Carnegie Mellon University, Pittsburgh, PA 15213 (United States)

    2012-11-15

    Total energy consumption of video game consoles has grown rapidly in the past few decades due to rapid increases in market penetration, power consumption of the devices, and increasing usage driven by new capabilities. Unfortunately, studies investigating the energy impacts of these devices have been limited and potential responses, such as ENERGY STAR requirements, have been difficult to define and implement. We estimate that the total electricity consumption of video game consoles in the US was around 11 TWh in 2007 and 16 TWh in 2010 (approximately 1 % of US residential electricity consumption), an increase of almost 50 % in 3 years. However, any estimate of total game console energy consumption is highly uncertain, and we have determined that the key uncertainty is the unknown consumer behavior with regards to powering down the system after use. Even under this uncertainty, we demonstrate that the most effective energy-saving modification is incorporation of a default auto power down feature, which could reduce electricity consumption of game consoles by 75 % (10 TWh reduction of electricity in 2010), saving consumers over USD 1 billion annually in electricity bills. We conclude that using an auto power down feature for game consoles is at least as effective for reducing energy consumption as implementing a strict set of energy efficiency improvements for the devices, is much easier to implement given the nature of the video game console industry, and could be applied retroactively to currently deployed consoles through firmware updates.

  7. Development of an Energy-Savings Calculation Methodology for Residential Miscellaneous Electric Loads: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Hendron, R.; Eastment, M.

    2006-08-01

    In order to meet whole-house energy savings targets beyond 50% in residential buildings, it will be essential that new technologies and systems approaches be developed to address miscellaneous electric loads (MELs). These MELs are comprised of the small and diverse collection of energy-consuming devices found in homes, including what are commonly known as plug loads (televisions, stereos, microwaves), along with all hard-wired loads that do not fit into other major end-use categories (doorbells, security systems, garage door openers). MELs present special challenges because their purchase and operation are largely under the control of the occupants. If no steps are taken to address MELs, they can constitute 40-50% of the remaining source energy use in homes that achieve 60-70% whole-house energy savings, and this percentage is likely to increase in the future as home electronics become even more sophisticated and their use becomes more widespread. Building America (BA), a U.S. Department of Energy research program that targets 50% energy savings by 2015 and 90% savings by 2025, has begun to identify and develop advanced solutions that can reduce MELs.

  8. Compact fluorescent lamps, innovation for electricity saving; Lamparas fluorescentes compactas, innovacion para el ahorro de electricidad

    Energy Technology Data Exchange (ETDEWEB)

    Rivera, Fernando [Fideicomiso para el Ahorro de Energia Electrica (Mexico); Camacho P, Wendolin E; Villalobos Alarcon, German [Phillips Lighting Mexico (Mexico)

    2007-01-15

    An extremely important resource is electricity because it has provided illumination for homes, buildings and cities in the absence of natural light. Therefore, the human being is considering to save this valuable resource by using sophisticated light bulbs. At the end of the 70's the compact fluorescent lamps appeared. In this article we can disclose the advantages and disadvantages of this technology, and how some years later of its invention, those lamps satisfied the client expectations, due to its cost, electricity saving, longer lifetime, use possibilities, and technological improvements. We can also know how Federal Electricity Commission (CFE) and The Trust Fund for Electric Energy Savings (FIDE) supported a project to favor these lamps to be in the Mexican market. [Spanish] La electricidad es un recurso de suma importancia porque ha contribuido a la iluminacion de casas, edificios y ciudades, ante la ausencia de luz natural, es por ello que se ha buscado ahorrar este recurso tan preciado con el uso de lamparas sofisticadas. Una tecnologia que aparecio a finales de los anos 70 fueron las lamparas fluorescentes compactas. En este articulo encontramos sus ventajas y desventajas, y como despues de algunos anos de su creacion comenzaron a llenar las expectativas del cliente gracias a su costo, ahorro de electricidad, mayor tiempo de vida, posibilidades de aplicacion y mejoras tecnologicas. Asi mismo podemos conocer, el proyecto que se hizo para que esta tecnologia entrara al mercado mexicano, con el apoyo de la Comision Federal de Electricidad (CFE) y del Fideicomiso para el Ahorro de Energia Electrica (FIDE).

  9. Customer-economics of residential photovoltaic systems (Part 1): The impact of high renewable energy penetrations on electricity bill savings with net metering

    International Nuclear Information System (INIS)

    Darghouth, Naïm R.; Barbose, Galen; Wiser, Ryan H.

    2014-01-01

    Residential photovoltaic (PV) systems in the US are often compensated at the customer's underlying retail electricity rate through net metering. Given the uncertainty in future retail rates and the inherent links between rates and the customer–economics of behind-the-meter PV, there is growing interest in understanding how potential changes in rates may impact the value of bill savings from PV. In this article, we first use a production cost and capacity expansion model to project California hourly wholesale electricity market prices under two potential electricity market scenarios, including a reference and a 33% renewables scenario. Second, based on the wholesale electricity market prices generated by the model, we develop retail rates (i.e., flat, time-of-use, and real-time pricing) for each future scenario based on standard retail rate design principles. Finally, based on these retail rates, the bill savings from PV is estimated for 226 California residential customers under two types of net metering, for each scenario. We find that high renewable penetrations can drive substantial changes in residential retail rates and that these changes, together with variations in retail rate structures and PV compensation mechanisms, interact to place substantial uncertainty on the future value of bill savings from residential PV. - Highlights: • We investigate the impact of high renewables on customer economics of solar. • We model three types of residential retail electricity rates. • Based on the rates, we calculate the bill savings from photovoltaic (PV) generation. • High renewables penetration can lead to lower bill savings with time-varying rates. • There is substantial uncertainty in the future bill savings from residential PV

  10. Holiday homes - electric power savings; Sommerhuse - elbesparelser her og nu

    Energy Technology Data Exchange (ETDEWEB)

    Kofoed Esbensen, N -U; Roed Rasmussen, E [Esbensen Raadgivende Ingenioerer A/S, Copenhagen (Denmark); Weldingh, P [Lokalenergi, Viby J. (Denmark); Worm, J; Adams Rasmussen, L [Energitjenesten, Aarhus (Denmark); Reuss, M [Elsparefonden, Copenhagen (Denmark); Ellehauge, K; Kjaergaard, C -J [Ellehauge og Kildemoes, Aarhus (Denmark); Jensen, Ole Michael [Aalborg Univ. SBi, Aalborg (Denmark)

    2010-09-15

    A questionnaire survey among 700 holiday home owners was conducted and followed up by interviews with representatives of typical groups of holiday home owners and a number of key persons representing rental, building, electricity supply, regulatory processing and supply of renewable energy facilities to holiday homes. The results of the questionnaire survey and of former surveys on technical savings potential are included in an easy-to-read catalogue of ideas with directions and recommendations for various groups of holiday home users and players. The recommendations are grouped into eight topics of more or less relevance for the various target groups. (LN)

  11. Electrical heating tapes, their use, energy consumption and energy savings potential

    International Nuclear Information System (INIS)

    Nipkow, J.; Lingenhel, S.

    2002-01-01

    Heating cables require about 0.6% of Swiss electricity consumption, approximately as much as all TV-sets. Most important applications are domestic hot water distribution tubing, frost protection (tubing, gutters) and industrial tubing, each requiring about 1/3. For over 10 years, self-regulating technology is standard for heating cables and offers pre-defined maintenance temperatures. To minimize electricity consumption, in most applications additional control devices (timer, temperature-/ power control) are necessary. The study could not give a general answer to whether domestic hot water distribution systems should be heated by heating cables or circulation systems. The best solution depends on the specific building circumstances. Conclusions of the technical and market analysis say that measures in different fields can transfer the saving potentials into practice: architects and designers of sanitary and electrical installations should be informed by articles in specialized magazines: the goal is either to avoid the use of heating cables or to minimize their electricity consumption, training of plumbers and electricians should treat the efficient use of heating cables. An instruction leaflet is to be created. Building owners and operators should be informed by their specialized magazines about problems with heating cables. (author)

  12. Does extending daylight saving time save energy? Evidence from an Australian experiment

    Energy Technology Data Exchange (ETDEWEB)

    Kellogg, R. [California Univ., Berkeley, CA (United States). Dept. of Agricultural and Resource Economics; Wolff, H. [California Univ., Berkeley, CA (United States). Dept. of Agricultural and Resource Economics]|[Forschungsinstitut zur Zukunft der Arbeit (IZA), Bonn (Germany)

    2007-03-15

    Several countries are considering extending Daylight Saving Time (DST) in order to conserve energy, and the U.S. will extend DST by one month beginning in 2007. However, projections that these extensions will reduce electricity consumption rely on extrapolations and simulations rather than empirical evidence. This paper, in contrast, examines a quasiexperiment in which parts of Australia extended DST in 2000 to facilitate the Sydney Olympics. Using detailed panel data and a triple differences specification, we show that the extension did not conserve electricity, and that a prominent simulation model overstates electricity savings when it is applied to Australia. (orig.)

  13. Energy Savings Potential and Opportunities for High-Efficiency Electric Motors in Residential and Commercial Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Goetzler, William [Navigant Consulting, Inc., Burlington, MA (United States); Sutherland, Timothy [Navigant Consulting, Inc., Burlington, MA (United States); Reis, Callie [Navigant Consulting, Inc., Burlington, MA (United States)

    2013-12-04

    This report describes the current state of motor technology and estimates opportunities for energy savings through application of more advanced technologies in a variety of residential and commercial end uses. The objectives of this report were to characterize the state and type of motor technologies used in residential and commercial appliances and equipment and to identify opportunities to reduce the energy consumption of electric motor-driven systems in the residential and commercial sectors through the use of advanced motor technologies. After analyzing the technical savings potential offered by motor upgrades and variable speed technologies, recommended actions are presented.

  14. Electricity savings from implementation of minimum energy efficiency standard for TVs in Malaysia

    Energy Technology Data Exchange (ETDEWEB)

    Varman, M.; Masjuki, H.H.; Mahlia, T.M.I. [University of Malaya, Kuala Lumpur (Malaysia). Department of Mechanical Engineering

    2005-06-01

    The popularization of 24 h pay-TV, interactive video games, web-TV, VCD and DVD in Malaysia are poised to have a large impact on overall TV electricity consumption in the country. With the increasing of overall TV energy consumption, energy efficiency standards are one of highly effective policies for decreasing electricity consumption in the residential sector. Energy efficiency standards are also capable of reducing consumer's electricity bill and contribute towards positive environmental impacts. This paper attempts to predict the amount of energy that can be saved in the residential sector by implementing minimum energy efficiency standard for television sets in Malaysia. Over the past 30 years, television ownership in Malaysian residents has increased from 186,036 units in 1970 to 2,741,640 units in 1991. This figure is expected to reach 6,201,316 units in the year 2010. Hence, efficiency improvement for this appliance will have a significant impact on the future of electricity consumption in this country. (author)

  15. Energy Savings Lifetimes and Persistence

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, Ian M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Schiller, Steven R. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Todd, Annika [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Billingsley, Megan A. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Goldman, Charles A. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Schwartz, Lisa C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2016-02-01

    This technical brief explains the concepts of energy savings lifetimes and savings persistence and discusses how program administrators use these factors to calculate savings for efficiency measures, programs and portfolios. Savings lifetime is the length of time that one or more energy efficiency measures or activities save energy, and savings persistence is the change in savings throughout the functional life of a given efficiency measure or activity. Savings lifetimes are essential for assessing the lifecycle benefits and cost effectiveness of efficiency activities and for forecasting loads in resource planning. The brief also provides estimates of savings lifetimes derived from a national collection of costs and savings for electric efficiency programs and portfolios.

  16. Material and energy flows in rotary kiln-electric furnace smelting of ferronickel alloy with energy saving

    International Nuclear Information System (INIS)

    Liu, Peng; Li, Baokuan; Cheung, Sherman C.P.; Wu, Wenyuan

    2016-01-01

    Highlights: • Establish the synergy relationship of material and energy in key RKEF processes. • Develop an analysis model to study energy saving with internal cycling of energy. • Analyze material and energy flow parameters and assess its associated synergy effect. • A methodology to evaluate the synergy and design indices of RKEF processes. - Abstract: An energy saving strategy with two energy saving measures has been proposed for reducing energy loss in the rotary kiln-electric furnace (RKEF) for the smelting of ferronickel alloy. One of the measures is to recover the waste heat of exhaust gas from the rotary kiln for preheating and dehydrating the wet laterite ores in the rotary dryer. Another measure is to recycle the furnace gas from the electric furnace into the rotary kiln as fuel. Based on the mass conservation and energy conservation laws, an analysis model of material and energy flows has been developed to understand the potential energy saving with the internal cycling of material and energy in the RKEF process. The analysis model not only considers the energy efficiency but also assess the synergy degree of system. Furthermore, the model also predicts the ratio of raw materials and the energy flow distribution to investigate residual heat and energy and analyze the effects of nickel content on energy flow. Finally, the evaluation methodology of synergy and the technic indices are also presented. Through the investigation of the synergy effect, the performance of the RKEF process can be evaluated and quantified for performance optimization in future.

  17. How much electricity can we save by using direct current circuits in homes? Understanding the potential for electricity savings and assessing feasibility of a transition towards DC powered buildings

    International Nuclear Information System (INIS)

    Glasgo, Brock; Azevedo, Inês Lima; Hendrickson, Chris

    2016-01-01

    Highlights: • DC distribution systems are analyzed using monitored appliance and solar PV data. • DC-distributed PV energy generates savings under real-world load and solar profiles. • Savings from direct-DC are generally not cost-effective in current markets. • Non-technical hurdles remain before DC can be widely adopted in US homes. - Abstract: Advances in semiconductor-based power electronics and growing direct current loads in buildings have led researchers to reconsider whether buildings should be wired with DC circuits to reduce power conversions and facilitate a transition to efficient DC appliances. The feasibility, energy savings, and economics of such systems have been assessed and proven in data centers and commercial buildings, but the outcomes are still uncertain for the residential sector. In this work, we assess the technical and economic feasibility of DC circuits using data for 120 traditionally-wired AC homes in Austin, Texas to understand the effect of highly variable demand profiles on DC-powered residences, using appliance-level use and solar generation data, and performing a Monte Carlo simulation to quantify costs and benefits. Results show site energy savings between 9% and 20% when solar PV is distributed to all home appliances. When battery storage for excess solar energy is considered, these savings increase to 14–25%. At present DC equipment prices, converting all equipment to DC causes levelized annual costs of electricity to homeowners to roughly double. However, by converting only homes’ air conditioning condensing units to DC, the costs of direct-DC are greatly reduced and home site energy savings of 7–16% are generated. In addition to quantifying savings, we find major nontechnical barriers to implementing direct-DC in homes. These include a lack of standards for such systems, a relatively small market for DC appliances and components, utility programs designed for AC power, and a workforce unfamiliar with DC

  18. Development of methods for evaluation of electricity saving and load levelling measures. Part 2: The planning and implementation of a power conservation campaign

    Energy Technology Data Exchange (ETDEWEB)

    Storm Soerensen, M.; Madsen, P.K. [NESA A/S, Research and Development Dept. (Denmark)

    1997-12-01

    In recent years many campaigns and projects have been carried out with the purpose of reducing the energy consumption. Simultaneously a lot of economic and structural changes are taking place in society in general; changes which also affect the size of the electricity consumption. Furthermore, there is a trend towards increased use of wind mills and decentral combined heating and power plants, which affects the electricity load of the local area. It is difficult to identify and separate the effect of each of these attitude-adjusting activities. The project `Development of methods for evaluation of the effect of electricity saving and load levelling measures` focuses on two different methods which, on different levels, can be used to determine the impact of different different activities on the electricity consumption. Both methods are based on mathematical statistics, and they consist of an analysis of historical data and a test campaign which will make it possible to test specific activities in a comparatively small scale. The historical part covers the years 1974 to 1994 and include such variables as: demography, economic factors, climatic conditions, periods of electricity saving campaigns, the start of billing according to time of day tariff etc. The wish to be able to measure the extent of these energy saving and load reducing initiatives resulted in a test campaign which was carried out under very restricted conditions starting in the fall of 1996. If the effect of the test campaign can be measured and as a consequence of this a method can be estimated, it will be possible to place models which can measure the effect of future campaigns. The primary object of the campaign is not the size of the electricity savings of the individual customer, but rather to obtain total savings for the entire group of customers. The test has been structured in a way which makes it possible to perform an analysis of the effect of the campaign by use of analysis of intervention

  19. Dedicated orthogeriatric service saves the HSE a million euro

    LENUS (Irish Health Repository)

    Shanahan, E

    2016-03-01

    Hip fracture is common in older adults and is associated with high morbidity, mortality and significant health care costs. A pilot orthogeriatrics service was established in an acute hospital. We aimed to establish the cost effectiveness of this service. Length of hospital stay, discharge destination and rehabilitation requirements were analysed for a one year period and compared to patients who received usual care prior to the service. We calculated the costs incurred and savings produced by the orthogeriatric service. Median length of stay was reduced by 3 days (p=<0.001) saving €266,976. There was a 19% reduction in rehabilitation requirements saving €192,600. Median rehabilitation length of stay was reduced by 6.5 days saving €171,093. Reductions in long term care requirements led to savings of €10,934 per week. Costs to establish such a service amount to €171,564. The introduction of this service led to improved patient outcomes in a cost effective manner.

  20. Gauging the Impact of Various Definitions of Low- and Moderate-Income Communities on Possible Electricity Savings From Weatherization

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, Ian M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2017-06-20

    With rising interest in lowering energy costs for low- and moderate-income households, the U.S. Department of Energy (DOE) asked Lawrence Berkeley National Laboratory (LBNL) to assess the implications of pursuing energy efficiency neighborhood-by-neighborhood where those households are most prevalent. DOE provided certain scenarios for qualifying geographic areas as “low- and moderate-income communities,” and LBNL used data on demographics, housing types and recent savings from low-income retrofits or weatherization to provide rough electricity savings estimates under those scenarios.

  1. The costs of the different pathways of electricity production and saving

    International Nuclear Information System (INIS)

    Dessus, B.

    2012-01-01

    The author discusses the content and methodology of a report published by the French Court of Audit on the assessment of the costs of the nuclear sector. He briefly recalls the principle adopted by the Court, i.e. the method of the economic current cost which calculates a global MWh cost on the whole operation duration of the selected production tool. The author discusses the application of this method to different electricity production and consumption sectors: ground-based wind energy, the Flamanville EPR, use of low-energy bulbs, air-air heat pumps, a refrigerator. He compares and discusses the results obtained for different electricity production sectors (EPR, ground-based wind energy, and gas combined cycle technology) and their sensitivity to adopted hypotheses. He comments the evolution of the investment cost of nuclear reactors in France, the economic current costs of offshore wind energy and small photovoltaic production. He finally discusses the economic current costs of the different ways of energy saving and their sensitivity to the adopted hypotheses

  2. Modelling of electricity savings in the Danish households sector: from the energy system to the end-user

    DEFF Research Database (Denmark)

    Baldini, Mattia; Trivella, Alessio

    2017-01-01

    sectors, has been extended in order to endogenously determine the best possible investments in more efficient home appliances. Second, we propose a method to relate the optimal energy system solution to the end-user choices by incorporating consumer behaviour and electricity price addition due to taxes...... of support to become profitable. The analysis quantifies energy and economic savings from the consumer side and reveals the impacts on the Danish power system and surrounding countries. Compared to a business-as-usual energy scenario, the end-user attains net economic savings in the range of 30–40 EUR per...

  3. ONCE AGAIN ABOUT DETERMINATION OF SAVING OF ENERGY FOR TRACTION DUE TO PARTIAL CUT–OFF OF TRACTION ENGINES OF ELECTRIC ROLLING STOCK

    Directory of Open Access Journals (Sweden)

    G. K. Getman

    2013-09-01

    Full Text Available Purpose. In general the well known methods for determination of energy saving due to the partial traction engines cut-off based on their comparison to efficiency coefficient or to the power of energy losses do not allow objective estimation of efficiency of these measures and in a number of cases result in erroneous results and errors. The search for new more advanced methods for determination of energy saving at the partial cut-off of the traction engines is needed. Methodology. The method of calculation determination of energy saving when partial cutting-off of the traction engines is offered. It is based on the use of rationality coefficient as the loading mode of the electric power consumption for the measuring instrument of transportation activity. Findings. Using the given mathematical expressions it is possible to determine the energy saving in both the relative and absolute values and set the terms (motion speed and route gradient, under which the energy saving will take place. Originality. The method of the task solving, which is based on the evaluation of energy consumption differences for the compared variants (not on the comparison of efficiency coefficient or differences of power of energy losses is offered. Practical value. The given methodology allows obtaining more exact conclusions in relation to the electric power consumption, as the comparison of energy losses power or the efficiency coefficient does not determine precisely the electric power consumption for traction. Therefore the conclusions based on the comparison of power of energy losses or efficiency coefficient can appear inexact.

  4. Streamlined energy-savings calculations for heat-island reduction strategies

    Energy Technology Data Exchange (ETDEWEB)

    Akbari, Hashem; Konopacki, Steven J.

    2003-03-15

    We have developed summary tables (sorted by heating- and cooling-degree-days) to estimate the potential of Heat-Island Reduction (HIR) strategies (i.e., solar-reflective roofs, shade trees, reflective pavements, and urban vegetation) to reduce cooling-energy use in buildings. The tables provide estimates of savings for both direct effect (reducing heat gain through the building shell) and indirect effect (reducing the ambient air temperature). In this analysis, we considered three building types that offer the most savings potential : residences, offices, and retail stores. Each building type was characterized in detail by Pre-1980 (old) or 1980+ (new) construction vintage and with natural gas or electricity as heating fuel. We defined prototypical-building characteristics for each building type and simulated the effects of HIR strategies on building cooling and heating energy use and peak power demand using the DOE-2.1E model and weather data for about 240 locations in the U.S. A statistical analysis of previously completed simulations for five cities was used to estimate the indirect savings. Our simulations included the effect of (1) solar-reflective roofing material on building [direct effect], (2) placement of deciduous shade trees near south and west walls of building [direct effect], and (3) ambient cooling achieved by urban reforestation and reflective building surfaces and pavements [indirect effect]. Upon completion of estimating the direct and indirect energy savings for all the selected locations, we integrated the results in tables arranged by heating- and cooling-degree-days. We considered 15 bins for heating-degree-days, and 11 bins for cooling-degree-days. Energy use and savings are presented per 1000 ft2 of roof area. In residences heated with gas and in climates with greater than 1000 cooling-degree-days, the annual electricity savings in Pre-1980 stock ranged from 650 to 1300 kWh/1000ft2; for 1980+ stock savings ranged 300 to 600 kWh/1000 ft2

  5. Energy Savings Measure Packages. Existing Homes

    Energy Technology Data Exchange (ETDEWEB)

    Casey, Sean [National Renewable Energy Lab. (NREL), Golden, CO (United States); Booten, Chuck [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2011-11-01

    This document presents the most cost effective Energy Savings Measure Packages (ESMP) for existing mixed-fuel and all electric homes to achieve 15% and 30% savings for each BetterBuildings grantee location across the United States. These packages are optimized for minimum cost to homeowners for source energy savings given the local climate and prevalent building characteristics (i.e. foundation types). Maximum cost savings are typically found between 30% and 50% energy savings over the reference home; this typically amounts to $300 - $700/year.

  6. Standardization for electric energy saving; Normalizacion para el ahorro de energia electrica

    Energy Technology Data Exchange (ETDEWEB)

    Reyes Diaz, Arturo [Fideicomiso de Apoyo al Programa de Ahorro de Energia del Sector Electrico (FIDE), Mexico, D. F. (Mexico)

    1994-12-31

    This work describes shortly the current legislation on the standardization; as well as the participation of the entities Fideicomiso de Apoyo al Programa de Ahorro de Energia del Sector Electrico (FIDE) and Programa de Ahorro de Energia (PAESE) in the consulting committees, for the elaboration of the Mexican official standards focussed to electric power saving. [Espanol] El presente trabajo, describe brevemente la legislacion actual sobre la normalizacion; asi como la participacion de las entidades Fideicomiso de Apoyo al Programa de Ahorro de Energia del Sector Electrico (FIDE) y Programa de ahorro de Energia (PAESE) en los comites consultivos, para la elaboracion de normas oficiales mexicanas enfocadas al ahorro de energia electrica.

  7. Standardization for electric energy saving; Normalizacion para el ahorro de energia electrica

    Energy Technology Data Exchange (ETDEWEB)

    Reyes Diaz, Arturo [Fideicomiso de Apoyo al Programa de Ahorro de Energia del Sector Electrico (FIDE), Mexico, D. F. (Mexico)

    1993-12-31

    This work describes shortly the current legislation on the standardization; as well as the participation of the entities Fideicomiso de Apoyo al Programa de Ahorro de Energia del Sector Electrico (FIDE) and Programa de Ahorro de Energia (PAESE) in the consulting committees, for the elaboration of the Mexican official standards focussed to electric power saving. [Espanol] El presente trabajo, describe brevemente la legislacion actual sobre la normalizacion; asi como la participacion de las entidades Fideicomiso de Apoyo al Programa de Ahorro de Energia del Sector Electrico (FIDE) y Programa de ahorro de Energia (PAESE) en los comites consultivos, para la elaboracion de normas oficiales mexicanas enfocadas al ahorro de energia electrica.

  8. Acquiring energy savings in manufactured housing

    International Nuclear Information System (INIS)

    Davey, D.

    1993-01-01

    In 1991, the Northwest utilities faced a complex situation. They needed new sources of electrical power to avoid future deficits. A significant block of energy savings was available in the manufactured housing sector in the form of energy savings from increased insulation to new manufactured homes. The manufacturers were interested in saving the electricity in the homes, but would only deal with the utility sector as a whole. Half of the homes targeted were sited in investor-owned utility (IOU) service territories, and half in the public sector made up of utilities that purchased some or all of their electricity from the Bonneville Power Administration. Utilities agreed to acquire energy from manufacturers In the form of thermal efficiency measures specified by the Bonneville Power Administration. The program that resulted from over one year of negotiations was called the Manufactured Housing Acquisition Program, or MAP. Manufacturers, the utilities, State Energy Offices, the Northwest Power Planning Council and Bonneville all worked closely and with tenacity to build the program that went into effect on April 1, 1992, and should save the region between 7 and 9 megawatts, enough energy to supply 11,000 homes in the Northwest

  9. Electricity-saving measures for electrical drives - Market analysis; Massnahmen zum Stromsparen bei elektrischen Antrieben. Marktanalyse in der Industrie. Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Baumgartner, W.; Ebert Bolla, O.; Puenzieux, P.

    2006-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) presents the results of work done on an empirical analysis of the results of a small-scale survey of industries as well as on various interviews with experts. Topics covered include the number of electrical motors in use in Switzerland, the number held in reserve, power consumption, part-load and over-dimensioning, operational factors, control strategies and the use of standardised motors. The data collected is presented in tabular and graphical form. Possibilities of making savings are discussed, as are obstacles to such work. Finally, ideas for an efficiency campaign are presented.

  10. Effective and persistent changes in household energy-saving behaviors: Evidence from post-tsunami Japan

    International Nuclear Information System (INIS)

    Fujimi, Toshio; Kajitani, Yoshio; Chang, Stephanie E.

    2016-01-01

    Highlights: • Some households’ adaptations to electricity shortage can be new efficient habits. • The electricity shortage in Japan was used as a natural experiment. • Some behaviors contributed to 2–4% electricity savings and persisted for two years. • Behaviors requiring frequency and discomfort cannot be effective or persistent. • Lowering the electricity-usage level of appliances might be a promising behavior. - Abstract: This paper focuses on households’ development of new energy-efficient habits as demonstrated in the context of a major electricity shortfall event. Energy conservation policies should encourage households to take measures that are actually effective in reducing energy consumption and that can be sustained over long periods of time. Few studies, however, have empirically examined what types of energy-saving measures are actually effective and persistent. The electricity shortages following the 2011 Great East Japan earthquake, tsunami, and nuclear disaster provided an opportunity to examine this question. A web survey of households in Japan was implemented to obtain data on metered electricity use in the summers of 2010–2013, household behaviors for electricity savings, and household socioeconomic attributes. Regression analysis was conducted to explain the effectiveness and persistence of energy saving behaviors. Results indicate that most households took several electricity-saving measures after the disaster to adapt to the electricity shortage. Certain types of measures led to 2–4% savings in electricity consumption (per measure) and persisted for two years. The effective and persistent electricity-saving measures tended to be those that did not require either frequent efforts or considerable discomfort. Findings suggest that electricity-saving behaviors requiring infrequent effort and little discomfort can become engrained as new habits or lifestyles. In particular, one promising measure may be to lower the electricity

  11. Estimation of the cost savings from participation of electric vehicles in Vehicle to Grid (V2G) schemes

    OpenAIRE

    Kiaee, Mahdi; Cruden, Andrew; Sharkh, S.M.

    2015-01-01

    The storage capacity of the batteries in an electric vehicle (EV) could be utilised to store electrical energy and give it back to the grid when needed by participating in vehicle to grid (V2G) schemes. This participation could be a source of revenue for vehicle owners thus reducing the total charging cost of their EVs. A V2G simulator has been developed using MATLAB to find out the potential cost saving from participation of EVs in V2G schemes. A standard IEEE30 network has been modelled in ...

  12. Electric power saving potential due to domestic refrigerators replacement; Potencial de ahorro de energia electrica por el reemplazo de refrigeradores domesticos

    Energy Technology Data Exchange (ETDEWEB)

    Peralta Solorio, Jose Luis [Fideicomiso para el Ahorro de Energia Electrica (Mexico)]. E-mail: jose.peralta@cfe.gob.mx

    2006-04-15

    In Mexico the second most used electrical appliance is: refrigerator. Owing to its use, it would be a promising option for electric power saving. In Guadalajara, Reynosa and Tampico it was performed a study with the aim of launching a project to replace the old refrigerators with new ones which are more effective and less expensive. Since the refrigerators cost and the electrical invoicing saving, the electric appliance change is profitable. To expect with this replacement more than eight million of refrigerators manufactured before 1997 will be changed. [Spanish] El refrigerador es el segundo electrodomestico mas utilizado a nivel nacional, esto permite que debido a su uso sea una opcion prometedora para el ahorro de energia electrica. Se hizo un estudio en Guadalajara, Reynosa y Tampico con el fin de lanzar un proyecto para sustituir los refrigeradores viejos por unos nuevos que sean mas eficaces y menos costosos. Por el costo de los refrigeradores y el ahorro en la facturacion electrica, el cambio de electrodomestico es rentable, de esta manera se espera que los mas de ocho millones de refrigeradores fabricados antes de 1997 que existen en el pais sean cambiados.

  13. Save energy - for industry

    International Nuclear Information System (INIS)

    Anon.

    1983-01-01

    The article is an interview with Glenn Bjorklund, Vice President of SCalEd (Southern California Edison). The variations in Californian power demand and public electricity consumption habits are explained, together with types of power source used in electricity production. Questions are posed concerning SCalEd's energy saving strategy. The political implications of electricity charge changes are discussed. The planned energy resources for 1982-1992 are given with nuclear power being the largest contributor. (H.J.P./G.T.H.)

  14. Electric drives

    CERN Document Server

    Boldea, Ion

    2005-01-01

    ENERGY CONVERSION IN ELECTRIC DRIVESElectric Drives: A DefinitionApplication Range of Electric DrivesEnergy Savings Pay Off RapidlyGlobal Energy Savings Through PEC DrivesMotor/Mechanical Load MatchMotion/Time Profile MatchLoad Dynamics and StabilityMultiquadrant OperationPerformance IndexesProblemsELECTRIC MOTORS FOR DRIVESElectric Drives: A Typical ConfigurationElectric Motors for DrivesDC Brush MotorsConventional AC MotorsPower Electronic Converter Dependent MotorsEnergy Conversion in Electric Motors/GeneratorsPOWER ELECTRONIC CONVERTERS (PECs) FOR DRIVESPower Electronic Switches (PESs)The

  15. Uncertainties in the Value of Bill Savings from Behind-the-Meter, Residential Photovoltaic Systems: The Roles of Electricity Market Conditions, Retail Rate Design, and Net Metering

    Science.gov (United States)

    Darghouth, Naim Richard

    Net metering has become a widespread policy mechanism in the U.S. for supporting customer adoption of distributed photovoltaics (PV), allowing customers with PV systems to reduce their electric bills by offsetting their consumption with PV generation, independent of the timing of the generation relative to consumption. Although net metering is one of the principal drivers for the residential PV market in the U.S., the academic literature on this policy has been sparse and this dissertation contributes to this emerging body of literature. This dissertation explores the linkages between the availability of net metering, wholesale electricity market conditions, retail rates, and the residential bill savings from behind-the-meter PV systems. First, I examine the value of the bill savings that customers receive under net metering and alternatives to net metering, and the associated role of retail rate design, based on current rates and a sample of approximately two hundred residential customers of California's two largest electric utilities. I find that the bill savings per kWh of PV electricity generated varies greatly, largely attributable to the increasing block structure of the California utilities' residential retail rates. I also find that net metering provides significantly greater bill savings than alternative compensation mechanisms based on avoided costs. However, retail electricity rates may shift as wholesale electricity market conditions change. I then investigate a potential change in market conditions -- increased solar PV penetrations -- on wholesale prices in the short-term based on the merit-order effect. This demonstrates the potential price effects of changes in market conditions, but also points to a number of methodological shortcomings of this method, motivating my usage of a long-term capacity investment and economic dispatch model to examine wholesale price effects of various wholesale market scenarios in the subsequent analysis. By developing

  16. Fossil energy savings potential of sugar cane bio-energy systems

    DEFF Research Database (Denmark)

    Nguyen, Thu Lan T; Hermansen, John Erik; Sagisaka, Masayuki

    2009-01-01

    One important rationale for bio-energy systems is their potential to save fossil energy. Converting a conventional sugar mill into a bio-energy process plant would contribute to fossil energy savings via the extraction of renewable electricity and ethanol substituting for fossil electricity...... and gasoline, respectively. This paper takes a closer look at the Thai sugar industry and examines two practical approaches that will enhance fossil energy savings. The first one addresses an efficient extraction of energy in the form of electricity from the excess bagasse and cane trash. The second while...... proposing to convert molasses or sugar cane to ethanol stresses the use of bagasse as well as distillery spent wash to replace coal in meeting ethanol plants' energy needs. The savings potential achieved with extracting ethanol from surplus sugar versus current practice in sugar industry in Thailand amounts...

  17. Saving more to consume more. EDF's communication ambiguities during the energy saving era

    International Nuclear Information System (INIS)

    Bouvier, Yves

    2012-01-01

    Since 1974, EDF is placed between a communication scheme imposed for energy savings and an industrial strategy of massive investment in nuclear power. In ten years, the company managed to increase households electricity consumption without advertising, due in particular to electric heating. But strong tensions were generated by this situation and led the company to develop an institutional communication to the employees and to the general public

  18. Using dew points to estimate savings during a planned cooling shutdown

    Science.gov (United States)

    Friedlein, Matthew T.; Changnon, David; Musselman, Eric; Zielinski, Jeff

    2005-12-01

    In an effort to save money during the summer of 2003, Northern Illinois University (NIU) administrators instituted a four-day working week and stopped air conditioning buildings for the three-day weekends (Friday through Sunday). Shutting down the air conditioning systems caused a noticeable drop in electricity usage for that part of the campus that features in our study, with estimated total electricity savings of 1,268,492 kilowatt-hours or 17% of the average usage during that eight-week period. NIU's air conditioning systems, which relied on evaporative cooling to function, were sensitive to dew point levels. Greatest savings during the shutdown period occurred on days with higher dew points. An examination of the regional dew point climatology (1959 2003) indicated that the average summer daily dew point for 2003 was 14.9°C (58.8°F), which fell in the lowest 20% of the distribution. Based on the relationship between daily average dew points and electrical usage, a predictive model that could estimate electrical daily savings was created. This model suggests that electrical savings related to any future three-day shutdowns over summer could be much greater in more humid summers. Studies like this demonstrate the potential value of applying climatological information and of integrating this information into practical decision-making.

  19. Impact of Extended Daylight Saving Time on National Energy Consumption Report to Congress

    Energy Technology Data Exchange (ETDEWEB)

    Belzer, D. B.; Hadley, S. W.; Chin, S-M.

    2008-10-01

    The Energy Policy Act of 2005 (Pub. L. No. 109-58; EPAct 2005) amended the Uniform Time Act of 1966 (Pub. L. No. 89-387) to increase the portion of the year that is subject to Daylight Saving Time. (15 U.S.C. 260a note) EPAct 2005 extended the duration of Daylight Saving Time in the spring by changing its start date from the first Sunday in April to the second Sunday in March, and in the fall by changing its end date from the last Sunday in October to the first Sunday in November. (15 U.S.C. 260a note) EPAct 2005 also called for the Department of Energy to evaluate the impact of Extended Daylight Saving Time on energy consumption in the United States and to submit a report to Congress. (15 U.S.C. 260a note) This report presents the results of impacts of Extended Daylight Saving Time on the national energy consumption in the United States. The key findings are: (1) The total electricity savings of Extended Daylight Saving Time were about 1.3 Tera Watt-hour (TWh). This corresponds to 0.5 percent per each day of Extended Daylight Saving Time, or 0.03 percent of electricity consumption over the year. In reference, the total 2007 electricity consumption in the United States was 3,900 TWh. (2) In terms of national primary energy consumption, the electricity savings translate to a reduction of 17 Trillion Btu (TBtu) over the spring and fall Extended Daylight Saving Time periods, or roughly 0.02 percent of total U.S. energy consumption during 2007 of 101,000 TBtu. (3) During Extended Daylight Saving Time, electricity savings generally occurred over a three- to five-hour period in the evening with small increases in usage during the early-morning hours. On a daily percentage basis, electricity savings were slightly greater during the March (spring) extension of Extended Daylight Saving Time than the November (fall) extension. On a regional basis, some southern portions of the United States exhibited slightly smaller impacts of Extended Daylight Saving Time on energy savings

  20. Saving Energy. Managing School Facilities, Guide 3.

    Science.gov (United States)

    Department for Education and Employment, London (England). Architects and Building Branch.

    This guide offers information on how schools can implement an energy saving action plan to reduce their energy costs. Various low-cost energy-saving measures are recommended covering heating levels and heating systems, electricity demand reduction and lighting, ventilation, hot water usage, and swimming pool energy management. Additional…

  1. Electric energy saving and its impact in the mining industry; El ahorro de energia electrica y su impacto en la industria minera

    Energy Technology Data Exchange (ETDEWEB)

    Urteaga Dufour, Jose Antonio [Fideicomiso de Apoyo al Programa de Ahorro de Energia del Sector Electrico (FIDE), Mexico, D. F. (Mexico)

    1994-12-31

    In this paper are shown the most important results of the energy diagnosis performed in some representative industries of the mining industry, where opportunity areas were detected in electric energy saving, starting from those measures that do not require investment up to the ones that require medium investment, recoverable in less than two years terms as a maximum and with electric energy saving ranging from 10% to 25%. [Espanol] En este trabajo, se presentan los resultados mas importantes, obtenidos en el diagnostico energetico realizado en algunas empresas representativas de la rama de la mineria, en donde se detectaron areas de oportunidad de ahorro de energia electrica que van desde aquellas medidas que no requieren inversiones hasta las que requieren medianas inversiones, recuperables en menos de dos anos como maximo y con ahorros de energia que van desde un 10% hasta un 25%.

  2. Electric energy saving and its impact in the mining industry; El ahorro de energia electrica y su impacto en la industria minera

    Energy Technology Data Exchange (ETDEWEB)

    Urteaga Dufour, Jose Antonio [Fideicomiso de Apoyo al Programa de Ahorro de Energia del Sector Electrico (FIDE), Mexico, D. F. (Mexico)

    1993-12-31

    In this paper are shown the most important results of the energy diagnosis performed in some representative industries of the mining industry, where opportunity areas were detected in electric energy saving, starting from those measures that do not require investment up to the ones that require medium investment, recoverable in less than two years terms as a maximum and with electric energy saving ranging from 10% to 25%. [Espanol] En este trabajo, se presentan los resultados mas importantes, obtenidos en el diagnostico energetico realizado en algunas empresas representativas de la rama de la mineria, en donde se detectaron areas de oportunidad de ahorro de energia electrica que van desde aquellas medidas que no requieren inversiones hasta las que requieren medianas inversiones, recuperables en menos de dos anos como maximo y con ahorros de energia que van desde un 10% hasta un 25%.

  3. Example for electrical energy savings with the pump adjustable electric drive

    International Nuclear Information System (INIS)

    Mirchevski, Slobodan; Andonov, Zdravko; Saracevic, Fahrudin; Micevski, Darko; Buchkoski, Aleksandar

    2004-01-01

    Most used method of flow regulation is by throttling the pipeline. Development of power electronic gives opportunity for induction motor pump drives speed control. The common ways of pump flow control are throttling, reducing the working circle, usage of fore circle shovels rotating, by pass and pump speed control Only pump speed control is the most suitable for the energy possibilities. Intensive development of power electronic gives. opportunity to create devices - power converters, which can change the speed of induction motor. For that improvement the energy savings the measurements of power consumption with throttling and speed control have been made. Also, the MATLAB-SIMULINK model of the measured system has been made. The economic effects of saving energy using adjustable speed drives are analyzed for the measured values. The analysis shows that the money payback period of speed controller investment is short compared with the drive lifetime (20 years). (Author)

  4. Design of energy saving monitoring system on isothermal oilless lubricated air compressor

    Science.gov (United States)

    Ma, S. N.; Liu, Q.; Xu, B. L.; Liu, Y.; Hu, F.

    2017-10-01

    This design introduces a kind of STM32F051C8T6 circuit monitoring system which is based on the ARM core. According to the operating principle of air compressor, the reduction of temperature and current is converted to save electricity and directly displayed, save electricity information stored at the same time, to achieve real-time monitoring air compressor energy saving effect in the process of operation.

  5. Evaluation of subsidy for electricity savings in households; Evaluering av tilskuddsordning for elektrisitetssparing i husholdninger

    Energy Technology Data Exchange (ETDEWEB)

    2010-04-15

    Ramboll Management Consulting (Ramboll) has on behalf of Enova SF (Enova) conducted an evaluation of the 'Grant Scheme for electricity savings in households'. The evaluation is conducted in the period January to March 2009, Ramboll is solely responsible for all the analysis, conclusions and recommendations in the report. The evaluation conducted on the basis of a review of the grant assessed on the basis of six evaluation themes. The evaluation will form the basis for further work on the grant by Enova and in their reporting to the Ministry of Petroleum and Energy (OED). (AG)

  6. Energy saving synergies in national energy systems

    DEFF Research Database (Denmark)

    Thellufsen, Jakob Zinck; Lund, Henrik

    2015-01-01

    In the transition towards a 100% renewable energy system, energy savings are essential. The possibility of energy savings through conservation or efficiency increases can be identified in, for instance, the heating and electricity sectors, in industry, and in transport. Several studies point...... to various optimal levels of savings in the different sectors of the energy system. However, these studies do not investigate the idea of energy savings being system dependent. This paper argues that such system dependency is critical to understand, as it does not make sense to analyse an energy saving...... without taking into account the actual benefit of the saving in relation to the energy system. The study therefore identifies a need to understand how saving methods may interact with each other and the system in which they are conducted. By using energy system analysis to do hourly simulation...

  7. Fossil energy savings potential of sugar cane bio-energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Thu Lan T. [Department of Agroecology, Aarhus University, Tjele (Denmark); The Joint Graduate School of Energy and Environment, King Mongkut' s University of Technology Thonburi, Bangkok (Thailand); Hermansen, John E. [Department of Agroecology, Aarhus University, Tjele (Denmark); Sagisaka, Masayuki [Institute of Science for Safety and Sustainability, National Institute of Advanced Industrial Science and Technology, Tsukuba (Japan)

    2009-11-15

    One important rationale for bio-energy systems is their potential to save fossil energy. Converting a conventional sugar mill into a bio-energy process plant would contribute to fossil energy savings via the extraction of renewable electricity and ethanol substituting for fossil electricity and gasoline, respectively. This paper takes a closer look at the Thai sugar industry and examines two practical approaches that will enhance fossil energy savings. The first one addresses an efficient extraction of energy in the form of electricity from the excess bagasse and cane trash. The second while proposing to convert molasses or sugar cane to ethanol stresses the use of bagasse as well as distillery spent wash to replace coal in meeting ethanol plants' energy needs. The savings potential achieved with extracting ethanol from surplus sugar versus current practice in sugar industry in Thailand amounts to 15 million barrels of oil a year. Whether the saving benefits could be fully realized, however, depends on how well the potential land use change resulting from an expansion of ethanol production is managed. The results presented serve as a useful guidance to formulate strategies that enable optimum utilization of biomass as an energy source. (author)

  8. Potential energy savings from cool roofs in Spain and Andalusia

    International Nuclear Information System (INIS)

    Boixo, Sergio; Diaz-Vicente, Marian; Colmenar, Antonio; Castro, Manuel Alonso

    2012-01-01

    Cool roofs are an inexpensive method to save energy and to improve the comfort level in buildings in mild and hot climates. A high scale implementation of cool roofs in Andalusia, in the south of Spain, could potentially save 295,000 kWh per year, considering only residential buildings with flat roofs using electrical heating. At the current energy prices, consumers can save 59 million euros annually in electricity costs and the emission of 136,000 metric tons of CO 2 can be directly avoided every year from the production of that electricity. If radiative forcings are considered, Andalucía can potentially offset between 9.44 and 12 Mt of CO 2 . All the provinces in the rest of Spain are also studied in this paper. The biggest savings are achieved in Gran Canaria (48%), Tenerife (48%), Cádiz (36%), Murcia (33%), Huelva (30%), Málaga (29%), Almería (29%) and Sevilla (28%), where savings are greater than 2 euros per square meter of flat roof for old buildings with dark roofs. For the biggest cities the range of savings obtained are: between 7.4% and 11% in Madrid, between 12% and 18% in Barcelona and between 14% and 20% in Valencia. -- Highlights: ► We estimate potential savings in energy, CO 2 , and money for cool roofs in Spain (residential sector with flat roofs). ► Average savings are of around one euro per square meter in the biggest cities. ► Potential savings are of more than 2 €/m 2 in the hottest cities. ► In Andalusia the potential savings are 300 MWh, 60 millions euro and 136,000 tons of CO 2 per year. ► With forcings, the CO 2 equivalence of cool roofs in Andalusia is between 9 and 12 Mt.

  9. Technical energy savings versus changes in human behaviour

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen

    1996-01-01

    Energy savings seems to be the most environmentally benign element in an energy policy. The paper is a reflection on the work on saving energy both by improving technology and by adapting human daily behaviour. A simple model is suggested for the energy chain which converts the primary energy all...... the way into human satisfaction via energy services. Results of various analyses and field experiments show saving potentials for electricity of 50 - 80 per cents. Barriers for implementing these technical saving options are discussed. Also the necessity and potentials for changing behavioural or life...

  10. Introduction criteria and concepts on energy saving in the technical standards for electric installations; Introduccion de criterios y conceptos de ahorro de energia en las normas tecnicas para instalaciones electricas

    Energy Technology Data Exchange (ETDEWEB)

    Rincon Nader, Jorge A [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1993-12-31

    The project Introduction Criteria and Concepts on Energy Saving in the Technical Standards for electric installations, is described, whose immediate objective is to recommend and in some cases regulate the use of energy saving equipment and devices and the adoption of attitudes and procedures that convey into saving, and the rational and efficient use of the electric energy. [Espanol] Se describe el proyecto Introduccion de Criterios y Conceptos de Ahorro de Energia en las Normas Tecnicas para instalaciones electricas, que tiene como objetivo inmediato recomendar, y en algunos casos reglamentar el uso de equipos y dispositivos ahorradores y la adopcion de actitudes y procedimientos que conduzcan a un ahorro y uso racional y eficiente de la energia electrica.

  11. Introduction criteria and concepts on energy saving in the technical standards for electric installations; Introduccion de criterios y conceptos de ahorro de energia en las normas tecnicas para instalaciones electricas

    Energy Technology Data Exchange (ETDEWEB)

    Rincon Nader, Jorge A. [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1992-12-31

    The project Introduction Criteria and Concepts on Energy Saving in the Technical Standards for electric installations, is described, whose immediate objective is to recommend and in some cases regulate the use of energy saving equipment and devices and the adoption of attitudes and procedures that convey into saving, and the rational and efficient use of the electric energy. [Espanol] Se describe el proyecto Introduccion de Criterios y Conceptos de Ahorro de Energia en las Normas Tecnicas para instalaciones electricas, que tiene como objetivo inmediato recomendar, y en algunos casos reglamentar el uso de equipos y dispositivos ahorradores y la adopcion de actitudes y procedimientos que conduzcan a un ahorro y uso racional y eficiente de la energia electrica.

  12. The Flanitzhuette project - solar island electricity supply combined with comprehensive electricity saving measures; Projekt Flanitzhuette - solare Inselstromversorgung in Kombination mit umfassenden Stromsparmassnahmen

    Energy Technology Data Exchange (ETDEWEB)

    Eingartner, M. [Abt. Marketing, Energiedienstleistungen, Regenerative Energien, Bayernwerk AG, Muenchen (Germany); Knapp, R. [Abt. Marketing, Energiedienstleistungen, Regenerative Energien, Bayernwerk AG, Muenchen (Germany); Kranz, U. [Abt. Marketing, Energiedienstleistungen, Regenerative Energien, Bayernwerk AG, Muenchen (Germany)

    1995-10-02

    Since 1992, Bayernwerk AG has been operating a solar island network at Flanitzhuette in the Bavarian Forest, to supply a remote hamlet. The plant is based on a photo-electric system together with a battery and a gas unit. The plant was designed by the least cost planning (LCP) process, ie: The electricity demand was first reduced by economy measures on the customers` side (demand side management, DSM) and then largely coverd by photo-electric supply. In the case of the `Flanitzhuette solar island`, the application of LCP was able to contribute to minimising the supply costs. The authors report on the project and the results in the electricity generation and saving areas. (orig.) [Deutsch] Die Bayernwerk AG betreibt seit 1992 in Flanitzhuette im Bayerischen Wald ein solares Inselstromnetz zur Versorgung eines abgelegenen Weilers. Die Anlage basiert auf einem Photovoltaik-System in Verbindung mit einer Batterieanlage und einem Gasaggregat. Bei der Konzeption der Anlage wurde nach dem Verfahren des Least-Cost Planning (LCP) vorgegangen, d.h. der Strombedarf wurde zunaechst durch wirtschaftliche Massnahmen auf der Kundenseite (Demand-Side Management, DSM) reduziert und erst anschliessend weitgehend photovoltaisch gedeckt. Im Falle der `Solarinsel Flanitzhuette` konnte die Anwendung von LCP zu einer Minimierung der Versorgungskosten beitragen. Die Verfasser berichten ueber das Projekt und die Ergebnisse im Stromerzeugungs- und Stromsparbereich. (orig.)

  13. Consumers’ perceptions of energy use and energy savings: A literature review

    Science.gov (United States)

    Lesic, Vedran; Bruine de Bruin, Wändi; Davis, Matthew C.; Krishnamurti, Tamar; Azevedo, Inês M. L.

    2018-03-01

    Background. Policy makers and program managers need to better understand consumers’ perceptions of their energy use and savings to design effective strategies for promoting energy savings. Methods. We reviewed 14 studies from the emerging interdisciplinary literature examining consumers’ perceptions electricity use by specific appliances, and potential savings. Results. We find that: (1) electricity use is often overestimated for low-energy consuming appliances, and underestimated for high-energy consuming appliances; (2) curtailment strategies are typically preferred over energy efficiency strategies; (3) consumers lack information about how much electricity can be saved through specific strategies; (4) consumers use heuristics for assessing the electricity use of specific appliances, with some indication that more accurate judgments are made among consumers with higher numeracy and stronger pro-environmental attitudes. However, design differences between studies, such as variations in reference points, reporting units and assessed time periods, may affect consumers’ reported perceptions. Moreover, studies differ with regard to whether accuracy of perceptions was evaluated through comparisons with general estimates of actual use, self-reported use, household-level meter readings, or real-time smart meter readings. Conclusion. Although emerging findings are promising, systematic variations in the measurement of perceived and actual electricity use are potential cause for concern. We propose avenues for future research, so as to better understand, and possibly inform, consumers’ perceptions of their electricity use. Ultimately, this literature will have implications for the design of effective electricity feedback for consumers, and related policies.

  14. An energy saving system for hospital laundries

    Energy Technology Data Exchange (ETDEWEB)

    Katsanis, J.S.; Tsarabaris, P.T.; Polykrati, A.D.; Proios, A.N. [National Technical Univ. of Athens, Athens (Greece). School of Electrical and Computer Engineering; Koufakis, E.I. [Public Power Corp. S.A., Crete (Greece)

    2009-07-01

    Hospital laundries are one of the largest consumers of water and electrical and thermal energy. This paper examined the energy savings achieved by a system using the hot wastewater from the washing process. Hospital laundries consume thermal energy using steam, which is produced in boilers by burning diesel oil or natural gas. Electrical energy for the mechanical drives, ventilation and also the lighting required in the laundry area are big consumers of energy. The paper presented the proposed system and discussed the parameters of the system and system dimensioning. The paper also provided and discussed an interpretation of steam and energy savings. The proposed system was considered to be economically viable, simple in its construction, installation and operation. From the application of the suggested system, the cost savings resulted in a satisfactory payback period for the capital invested of approximately three to five years. 14 refs., 4 tabs., 2 figs.

  15. Energy saving potential in existing industrial compressors

    International Nuclear Information System (INIS)

    Vittorini, Diego; Cipollone, Roberto

    2016-01-01

    The Compressed Air Sector accounts for a mean 10% worldwide electricity consumption, which ensures about its importance, when energy saving and CO_2 emissions reduction are in question. Since the compressors alone account for 15% overall industry electricity consumption, it appears vital to pay attention to machine performances. The paper presents an overview of present compressor technology and focuses on saving directions for screw and sliding vanes machines, according to data provided by the Compressed Air and Gas Institute and PNEUROP. Data were processed to obtain consistency with fixed reference pressures and organized as a function of main operating parameters. Each sub-term, contributing to the overall efficiency (adiabatic, volumetric, mechanical, electric, organic), was considered separately: the analysis showed that the thermodynamic improvement during compression achievable by splitting the compression in two stages, with a lower compression ratio, opens the way to significantly reduce the energy specific consumption. - Highlights: • Compressors technology overview in industrial compressed air systems. • Market compressors efficiency baseline definition. • Energy breakdown and evaluation of main efficiency terms. • Assessment of air cooling-related energy saving potential. • Energy specific consumption reduction through dual stage compression.

  16. Electricity demand savings from distributed solar photovoltaics

    International Nuclear Information System (INIS)

    Glassmire, John; Komor, Paul; Lilienthal, Peter

    2012-01-01

    Due largely to recent dramatic cost reductions, photovoltaics (PVs) are poised to make a significant contribution to electricity supply. In particular, distributed applications of PV on rooftops, brownfields, and other similar applications – hold great technical potential. In order for this potential to be realized, however, PV must be “cost-effective”—that is, it must be sufficiently financially appealing to attract large amounts of investment capital. Electricity costs for most commercial and industrial end-users come in two forms: consumption (kWh) and demand (kW). Although rates vary, for a typical larger commercial or industrial user, demand charges account for about ∼40% of total electricity costs. This paper uses a case study of PV on a large university campus to reveal that even very large PV installations will often provide very small demand reductions. As a result, it will be very difficult for PV to demonstrate cost-effectiveness for large commercial customers, even if PV costs continue to drop. If policymakers would like PV to play a significant role in electricity generation – for economic development, carbon reduction, or other reasons – then rate structures will need significant adjustment, or improved distributed storage technologies will be needed. - Highlights: ► Demand charges typically account for ∼40% of total electricity costs for larger electricity users. ► Distributed photovoltaic (PV) systems provide minimal demand charge reductions. ► As a result, PVs are not a financially viable alternative to centralized electricity. ► Electricity rate structures will need changes for PV to be a major electricity source.

  17. Saving electrical energy in a saw-mill; Einsparung von elektrischer Energie in einem Saegereibetrieb. Stromeinsparungen in den Bereichen Holzbearbeitung, Foerdertechnik, Holztrocknung, Absauganlagen, Druckluft, Beleuchtung

    Energy Technology Data Exchange (ETDEWEB)

    Wyrsch, I. [Wyrsch Technologies, Kuessnacht am Rigi (Switzerland); Dolder, M. [Ingenieurbuero Dolder, Luzern (Switzerland)

    2005-01-15

    This comprehensive, illustrated report for the Swiss Federal Office of Energy (SFOE) presents the findings of a project that examined the electricity consumption of saw-mills and ways in which the amount of electrical power used in such facilities could be reduced. The Schilliger Holz AG company was taken as an example of a saw-mill in Switzerland. Its power consumption in 2001 was almost 6 gigawatt-hours. The work done in the two phases of the project is described and commented on. The first phase involved the measurement and analysis of power consumption; in the second phase measures to be taken to help save energy were developed. The various machinery and installations in this saw mill are described. These include various systems for the processing of the raw timber through to finished products that include wood for building, decoration and laminates. Measurement data is presented and commented on. Potentials for saving electricity and measures to be taken are described in detail for the various processing plants in the saw-mill.

  18. Navigation API Route Fuel Saving Opportunity Assessment on Large-Scale Real-World Travel Data for Conventional Vehicles and Hybrid Electric Vehicles: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Lei [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Holden, Jacob [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gonder, Jeffrey D [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-12-06

    The green routing strategy instructing a vehicle to select a fuel-efficient route benefits the current transportation system with fuel-saving opportunities. This paper introduces a navigation API route fuel-saving evaluation framework for estimating fuel advantages of alternative API routes based on large-scale, real-world travel data for conventional vehicles (CVs) and hybrid electric vehicles (HEVs). The navigation APIs, such Google Directions API, integrate traffic conditions and provide feasible alternative routes for origin-destination pairs. This paper develops two link-based fuel-consumption models stratified by link-level speed, road grade, and functional class (local/non-local), one for CVs and the other for HEVs. The link-based fuel-consumption models are built by assigning travel from a large number of GPS driving traces to the links in TomTom MultiNet as the underlying road network layer and road grade data from a U.S. Geological Survey elevation data set. Fuel consumption on a link is calculated by the proposed fuel consumption model. This paper envisions two kinds of applications: 1) identifying alternate routes that save fuel, and 2) quantifying the potential fuel savings for large amounts of travel. An experiment based on a large-scale California Household Travel Survey GPS trajectory data set is conducted. The fuel consumption and savings of CVs and HEVs are investigated. At the same time, the trade-off between fuel saving and time saving for choosing different routes is also examined for both powertrains.

  19. Energy at the author's house for saving conventional fuels

    International Nuclear Information System (INIS)

    Nandwani, S.S.

    2006-01-01

    About 20 years ago, we decided to make our house. Being working on the utilization of solar energy and with the objective of saving maximum conventional fuel and some family budget, we dicided to make use of maximum this free and clean fuel. After buying the land with proper orientation, we installed different cheap devices and left the proper provision for another devices to installed in future. At present we solar energy mainly for cooking, water heating for bath and dish washing, drying clothes/fruits/vegetables, purification (pasteurization) of water. In addition. we also use solar cells for some electrical devices like solar radio, solar lamp for emergency, charging batteries and mobile phone etc. For our family of five persons, having 3 coloured TV, 2 computers using many hours of Internet, without any use of fuel other than electricity and sun, our electricity consumption is of the order of 270 (dry/summer)-350 (wet/rainy) kWh/month, depending on the season (US$16-21/month). This is roughly 40-50% of the electricity consumed by my other colleagues who do not use solar energy. With this saving, the initial cost of solar devices (US$1200-1400) is already recovered. In this presentation, construction and results of working of these solar thermal, electrical devices and other energy saving means at our house are mentioned.(Author)

  20. Characterization of the household electricity consumption in the EU, potential energy savings and specific policy recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Fonseca, Paula; Almeida, Anibal de (ISR-Univ. of Coimbra, Dep. Electrical Engineering (Portugal)). e-mail: pfonseca@isr.uc.pt; Feilberg, Nicolai (SINTEF Energiforskning AS (Norway)); Markogiannakis, George (Centre for Renewable Energy Sources - CRES (Greece)); Kofod, Casper (Energy piano (Denmark))

    2009-07-01

    Although significant improvements in energy efficiency have been achieved in home appliances and lighting, the electricity consumption in the average EU-27 household has been increasing by about 2% per year during the past 10 years. Some reasons for such increase are associated with an increased degree of basic comfort and level of amenities (particularly in the new EU member countries) and also with the widespread utilization of relatively new types of loads whose penetration and use has experienced a very significant growth in recent years. With the objective of contributing to an increased understanding of the energy consumption in the EU-27 households for the different types of equipment including the consumers' behaviour and comfort levels, and to identify demand trends, a large energy monitoring campaign, co-funded by the IEE programme, was carried out in 12 countries, accompanied by a lifestyle consumer survey. From the measurements carried out it can be concluded that IT and entertainment loads, including standby, are a key contributor to the power demand. In basically all types of loads there is wide range of performance levels, including new emerging technologies, in the models available in the market. Available technology, associated with responsible consumer behaviour, can reduce wasteful consumption. The potential electricity savings that exist in the residential sector in Europe, and that can already be implemented by existing means, like the use of BAT (best available technology) efficient appliances or the elimination/mitigation of standby consumption, can reach up to 48% savings. Specific policy recommendations to promote market transformation and behavioural changes in the equipment selection and operation have been identified.

  1. Lighting Energy Saving with Light Pipe in Farm Animal Production

    Directory of Open Access Journals (Sweden)

    Hans von Wachenfelt

    2015-12-01

    Full Text Available The Swedish animal production sector has potential for saving electric lighting of €4-9 million per year using efficient daylight utilisation. To demonstrate this, two light pipe systems, Velux® (house 1 and Solatube® (house 2, are installed in two identical pig houses to determine if the required light intensity, daylight autonomy (DA, and reduced electricity use for illumination can be achieved. In each house, three light sensors continuously measure the indoor daylight relative to an outdoor sensor. If the horizontal illuminance at pig height decreases below 40 lux between 08.00 and 16.00 hours, an automatic control system activates the lights, and electricity use is measured. The daylight factor (DF and DA are determined for each house, based on annual climate data. The mean annual DA of 48% and 55% is achieved for house 1 and house 2, respectively. Light pipes in house 2 have delivered significantly more DA than those in house 1. The most common illuminance range between 0 and 160 lux is recorded in both houses, corresponding to approximately 82% and 83% of daylight time for house 1 and house 2, respectively. Further, the daylighting system for house 2 has produced a uniform DF distribution between 0.05 and 0.59. The results demonstrate that considerable electric energy savings can be achieved in the animal production sector using light pipes. Saving 50% of electric lighting would correspond to 36 GWh or 2520 t CO2 per year for Sweden, but currently the energy savings are not making the investment profitable.

  2. Electricity savings in households with everyday IT

    DEFF Research Database (Denmark)

    Kibsgaard, Kaj; Larsen, Anders; leth, Søren

    This paper analyzes the effect of supplying online feedback by SMS-text messages and email about electricity consumption on the level of total household electricity consumption. An experiment was conducted where 1,452 households were randomly allocated to three experimental groups and two control...... groups. Feedback was supplied throughout 2007 to members of the experiment groups who accepted the invitation, and data on consumption of electricity for 2006 and 2007 collected for all participants and control group members. 30% of the households invited to receive feedback accepted the invitation....... The estimated effects of the feedback on consumption of electricity are estimated to be in the range of 2-3%. The feedback technology is cheap to implement and therefore likely to be cost-effective...

  3. Saving energy and reducing CO2 with electricity

    International Nuclear Information System (INIS)

    Yau, T.S.; Zaininger, H.W.

    1991-10-01

    Surprising potential exists for new and enhanced electric technologies to reduce energy use and CO 2 emission. Widespread deployment of these technologies could reduce energy use by up to 7 quads in 2010 and a corresponding reduction in carbon dioxide emission of up to 440 million tons. Electricity's unique high form value allows for efficiency at the point of end-use that is multiples of the efficiency possible in gas- or oil-fueled systems. The efficiency advantage at the point of end use more than offset the disadvantage of the high losses in the production of electricity. Hence, widespread deployment of many electric end uses will reduce the nation's total energy requirements. Major technologies which hold the greatest potential include electric process heating, industrial electrotechnologies, electric vehicles, information technologies that substitute electronic communication for transportation of people, and electric heat pumps for space heating, cooling and water heating. Wider use of these beneficial technologies in combination with the efficient use of electricity can reduce the nation's primary energy use and Co 2 emissions from electric generation by more than a quarter. 35 refs., 50 figs., 69 tabs

  4. VO2 thermochromic smart window for energy savings and generation

    Science.gov (United States)

    Zhou, Jiadong; Gao, Yanfeng; Zhang, Zongtao; Luo, Hongjie; Cao, Chuanxiang; Chen, Zhang; Dai, Lei; Liu, Xinling

    2013-10-01

    The ability to achieve energy saving in architectures and optimal solar energy utilisation affects the sustainable development of the human race. Traditional smart windows and solar cells cannot be combined into one device for energy saving and electricity generation. A VO2 film can respond to the environmental temperature to intelligently regulate infrared transmittance while maintaining visible transparency, and can be applied as a thermochromic smart window. Herein, we report for the first time a novel VO2-based smart window that partially utilises light scattering to solar cells around the glass panel for electricity generation. This smart window combines energy-saving and generation in one device, and offers potential to intelligently regulate and utilise solar radiation in an efficient manner.

  5. A technical analysis for cogeneration systems with potential applications in twelve California industrial plants. [energy saving heat-electricity utility systems

    Science.gov (United States)

    Moretti, V. C.; Davis, H. S.; Slonski, M. L.

    1978-01-01

    In a study sponsored by the State of California Energy Resources Conservation and Development Commission, 12 industrial plants in five utility districts were surveyed to assess the potential applications of the cogeneration of heat and electricity in California industry. Thermodynamic calculations were made for each plant in determining the energy required to meet the existing electrical and steam demands. The present systems were then compared to conceptual cogeneration systems specified for each plant. Overall energy savings were determined for the cogeneration applications. Steam and gas turbine topping cycle systems were considered as well as bottoming cycle systems. Types of industries studied were: pulp and paper, timber, cement, petroleum refining, enhanced oil recovery, foods processing, steel and glass

  6. Mission aware energy saving strategies for Army ground vehicles

    Science.gov (United States)

    Dattathreya, Macam S.

    Fuel energy is a basic necessity for this planet and the modern technology to perform many activities on earth. On the other hand, quadrupled automotive vehicle usage by the commercial industry and military has increased fuel consumption. Military readiness of Army ground vehicles is very important for a country to protect its people and resources. Fuel energy is a major requirement for Army ground vehicles. According to a report, a department of defense has spent nearly $13.6 billion on fuel and electricity to conduct ground missions. On the contrary, energy availability on this plant is slowly decreasing. Therefore, saving energy in Army ground vehicles is very important. Army ground vehicles are embedded with numerous electronic systems to conduct missions such as silent and normal stationary surveillance missions. Increasing electrical energy consumption of these systems is influencing higher fuel consumption of the vehicle. To save energy, the vehicles can use any of the existing techniques, but they require complex, expensive, and time consuming implementations. Therefore, cheaper and simpler approaches are required. In addition, the solutions have to save energy according to mission needs and also overcome size and weight constraints of the vehicle. Existing research in the current literature do not have any mission aware approaches to save energy. This dissertation research proposes mission aware online energy saving strategies for stationary Army ground vehicles to save energy as well as to meet the electrical needs of the vehicle during surveillance missions. The research also proposes theoretical models of surveillance missions, fuzzy logic models of engine and alternator efficiency data, and fuzzy logic algorithms. Based on these models, two energy saving strategies are proposed for silent and normal surveillance type of missions. During silent mission, the engine is on and batteries power the systems. During normal surveillance mission, the engine is

  7. Motor Assembly Plant Saves$85,000 with Compressed Air System Improvements (Bodine Electric's Chicago Facility): Office of Industrial Technologies (OIT) BestPractices Technical Case Study

    International Nuclear Information System (INIS)

    Wogsland, J.

    2001-01-01

    This case study is one in a series on industrial firms who are implementing energy efficient technologies and system improvements into their manufacturing processes. This case study documents the activities, savings, and lessons learned on the Bodine Electric motor assembly plant project

  8. Good practice in saving energy at school

    Science.gov (United States)

    Veronesi, Paola; Bonazzi, Enrico

    2014-05-01

    We teach students between 14 and 18 years old at a high school in Italy. In the first class, one of the topics we treat is related to the atmosphere. The students learn the composition of air, the importance of the natural greenhouse effect in keeping the average temperature of the planet and how human activity is increasing the level of greenhouse gases, enhancing greenhouse effect and causing global warming. It is possible to reach this knowledge using different materials and methods such as schoolbooks, articles, websites or films, individual or group work, but as students gradually become aware of the problem of climate change due to global warming, it is necessary to propose a solution that can be experienced and measured by students. This is the aim of the project "Switch off the light, to switch on the future". The project doesn't need special materials to be carried out but all the people in the community who work and "live" at school should participate in it. The project deals directly with saving electric energy, by changing the habits of the use of electricity. Saving electric energy means saving CO2 emitted to atmosphere, and consequently contributing to the reduction of greenhouse gases emission. Normally, lights in the school are switched on in the early morning and switched off at the end of lessons. Nobody is responsible to turn out the lights in classes, so students choose one or two "Light guardians" who are responsible for the light management. Simple rules for light management are written and distributed in the classes so that the action of saving energy is spread all over the school. One class participates in the daily data collection from the electricity meter, before and after the beginning of the action. At the end of the year the data are treated and presented to the community, verifying if the electric consumption has been cut down or not. This presentation is public, with students who directly introduce collected data, results and

  9. Functional Median Polish

    KAUST Repository

    Sun, Ying

    2012-08-03

    This article proposes functional median polish, an extension of univariate median polish, for one-way and two-way functional analysis of variance (ANOVA). The functional median polish estimates the functional grand effect and functional main factor effects based on functional medians in an additive functional ANOVA model assuming no interaction among factors. A functional rank test is used to assess whether the functional main factor effects are significant. The robustness of the functional median polish is demonstrated by comparing its performance with the traditional functional ANOVA fitted by means under different outlier models in simulation studies. The functional median polish is illustrated on various applications in climate science, including one-way and two-way ANOVA when functional data are either curves or images. Specifically, Canadian temperature data, U. S. precipitation observations and outputs of global and regional climate models are considered, which can facilitate the research on the close link between local climate and the occurrence or severity of some diseases and other threats to human health. © 2012 International Biometric Society.

  10. Importance of the validation of saving technologies of electric power; Importancia de la validacion de tecnologias ahorradoras de energia electrica

    Energy Technology Data Exchange (ETDEWEB)

    Valer Negrete, Adrian [Programa de Ahorro de Energia del Sector Electrico (PAESE), Comision Federal de Electricidad (Mexico)

    2003-07-01

    Within the Programs of Energy Saving it is fundamental the search and application of new technologies, with which this saving can be obtained, selected with base in their technical characteristics that allow to reduce to the consumptions and demands of power, without damaging the electric networks nor the transformers of the Comision Federal de Electricidad. It is important that the investments which are made count on attractive periods of capital recovery, in comparison with the useful life of the product, reason why the knowledge and price of the new technologies will be parameters to consider in an important manner, creating the need of conducting tests that verify the veracity of the information of the supplier, resulting in certain cases, the change of design of these technologies, so that thus they fulfill the engaged characteristics. This paper indicates the characteristics that the new saving technologies of electrical energy must fulfill and the tests and parameters to consider their evaluation. [Spanish] Dentro de los Programas de Ahorro de Energia es fundamental la busqueda y aplicacion de nuevas tecnologias, con las que se pueda obtener dicho ahorro, seleccionadas con base en sus caracteristicas tecnicas que permitan reducir los consumos y demandas de potencia, sin danar las redes ni transformadores de la Comision Federal de Electricidad. Es importante que las inversiones que se realicen cuenten con periodos de recuperacion de capital atractivos, comparados con la vida util del producto, por lo que el conocimiento y precio de las nuevas tecnologias seran parametros a considerar de manera importante, creandose la necesidad de realizar pruebas que verifiquen la veracidad de la informacion del proveedor, resultando en determinados casos, el cambio de diseno de dichas tecnologias, para que asi cumplan las caracteristicas prometidas. Este trabajo indica las caracteristicas que deben cumplir las nuevas tecnologias ahorradoras de energia electrica y las

  11. Public-opinion poll on energy saving

    International Nuclear Information System (INIS)

    1982-01-01

    A public-opinion poll was carried out on energy saving from November 26 to December 2, 1981, across the country. The number of persons participated in the survey was 5,000, whose age was 20 and above. The recovery ratio was 4,007 persons (80.1 %). The results of the survey and also the question-answer form are given with respective percentages. The questions were in the following three categories: (1) cognizance of energy saving - space-heating temperature, energy saving conscience use of private cars, purchase of highenergy consumption appliances; (2) energy for future - energy consumption, energy consumption trend, new types of energy, main sources of power generation, nuclear power in the overall electric power, apprehension toward nuclear power plants, safety measures in nuclear power plants; (3) governmental energy policy measures. (J.P.N.)

  12. Assessment of Energy Conservation in Egypt's Electric System

    Directory of Open Access Journals (Sweden)

    Azhar El Saeed Awad Abou Ghoniem

    2017-03-01

    Full Text Available This paper provides an evaluation of energy saving policy as a key factor in Egypt's electric system in terms of benefits, invested cost, power quality and environmental impact, solutions have been made by system planners and decision makers aiming to face the challenges that being encountered by the electric system such as scarce and precious of prime energies are compared in terms of invested cost, implementation time and advantages for both of power providers and end users w.r.to energy savings. A case study that implemented in a pilot program for energy savings was given. It is a group of facilities include industrial, commercial, administrative companies and worship houses, they are connected to Alexandria electrical distribution network, they are classified as big customers, i.e. contracted power for each is higher than 0.5 mega watt, the goals of the program were evaluating potentials of energy saving opportunities in the system and estimating the outcomes. Options were evaluated with regard to savings in electricity, fuels and water. Cost of investments and pay back periods were calculated. Environmental impact as a result of saving in emitted green house gas co2 is determined. Potentials of energy savings are analyzed and benefits to both electric utilities and end users were assessed.

  13. Review of the Fuel Saving, Life Cycle GHG Emission, and Ownership Cost Impacts of Lightweighting Vehicles with Different Powertrains.

    Science.gov (United States)

    Luk, Jason M; Kim, Hyung Chul; De Kleine, Robert; Wallington, Timothy J; MacLean, Heather L

    2017-08-01

    The literature analyzing the fuel saving, life cycle greenhouse gas (GHG) emission, and ownership cost impacts of lightweighting vehicles with different powertrains is reviewed. Vehicles with lower powertrain efficiencies have higher fuel consumption. Thus, fuel savings from lightweighting internal combustion engine vehicles can be higher than those of hybrid electric and battery electric vehicles. However, the impact of fuel savings on life cycle costs and GHG emissions depends on fuel prices, fuel carbon intensities and fuel storage requirements. Battery electric vehicle fuel savings enable reduction of battery size without sacrificing driving range. This reduces the battery production cost and mass, the latter results in further fuel savings. The carbon intensity of electricity varies widely and is a major source of uncertainty when evaluating the benefits of fuel savings. Hybrid electric vehicles use gasoline more efficiently than internal combustion engine vehicles and do not require large plug-in batteries. Therefore, the benefits of lightweighting depend on the vehicle powertrain. We discuss the value proposition of the use of lightweight materials and alternative powertrains. Future assessments of the benefits of vehicle lightweighting should capture the unique characteristics of emerging vehicle powertrains.

  14. Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Garbesi, Karina; Vossos, Vagelis; Sanstad, Alan; Burch, Gabriel

    2011-10-13

    An increasing number of energy efficient appliances operate on direct current (DC) internally, offering the potential to use DC from renewable energy systems directly and avoiding the losses inherent in converting power to alternating current (AC) and back. This paper investigates that potential for net-metered residences with on-site photovoltaics (PV) by modeling the net power draw of the ‘direct-DC house’ with respect to today’s typical configuration, assuming identical DC-internal loads. Power draws were modeled for houses in 14 U.S. cities, using hourly, simulated PV-system output and residential loads. The latter were adjusted to reflect a 33% load reduction, representative of the most efficient DC-internal technology, based on an analysis of 32 electricity end-uses. The model tested the effect of climate, electric vehicle (EV) loads, electricity storage, and load shifting on electricity savings; a sensitivity analysis was conducted to determine how future changes in the efficiencies of power system components might affect savings potential. Based on this work, we estimate that net-metered PV residences could save 5% of their total electricity load for houses without storage and 14% for houses with storage. Based on residential PV penetration projections for year 2035 obtained from the National Energy Modeling System (2.7% for the reference case and 11.2% for the extended policy case), direct-DC could save the nation 10 trillion Btu (without storage) or 40 trillion Btu (with storage). Shifting the cooling load by two hours earlier in the day (pre-cooling) has negligible benefits for energy savings. Direct-DC provides no energy savings benefits for EV charging, to the extent that charging occurs at night. However, if charging occurred during the day, for example with employees charging while at work, the benefits would be large. Direct-DC energy savings are sensitive to power system and appliance conversion efficiencies but are not significantly

  15. Electric portfolio modeling with stochastic water - climate interactions: Implications for co-management of water and electric utilities

    Science.gov (United States)

    Woldeyesus, Tibebe Argaw

    Water supply constraints can significantly restrict electric power generation, and such constraints are expected to worsen with future climate change. The overarching goal of this thesis is to incorporate stochastic water-climate interactions into electricity portfolio models and evaluate various pathways for water savings in co-managed water-electric utilities. Colorado Springs Utilities (CSU) is used as a case study to explore the above issues. The thesis consists of three objectives: Characterize seasonality of water withdrawal intensity factors (WWIF) for electric power generation and develop a risk assessment framework due to water shortages; Incorporate water constraints into electricity portfolio models and evaluate the impact of varying capital investments (both power generation and cooling technologies) on water use and greenhouse gas emissions; Compare the unit cost and overall water savings from both water and electric sectors in co-managed utilities to facilitate overall water management. This thesis provided the first discovery and characterization of seasonality of WWIF with distinct summertime and wintertime variations of +/-17% compared to the power plant average (0.64gal/kwh) which itself is found to be significantly higher than the literature average (0.53gal/kwh). Both the streamflow and WWIF are found to be highly correlated with monthly average temperature (r-sq = 89%) and monthly precipitation (r-sq of 38%) enabling stochastic simulation of future WWIF under moderate climate change scenario. Future risk to electric power generation also showed the risk to be underestimated significantly when using either the literature average or the power plant average WWIF. Seasonal variation in WWIF along with seasonality in streamflow, electricity demand and other municipal water demands along with storage are shown to be important factors for more realistic risk estimation. The unlimited investment in power generation and/or cooling technologies is also

  16. Savings in its sights for Somerset Trust.

    Science.gov (United States)

    Russell, Colin

    2011-10-01

    Colin Russell, healthcare specialist at Schneider Electric (pictured), explains how the company has recently worked with Taunton and Somerset NHS Foundation Trust to implement a major energy-saving project at the Trust's Musgrove Park Hospital in Taunton. He argues that, at a time when all areas of the service are being asked to reduce costs, such partnerships can potentially save the institution millions of pounds and significantly reduce carbon emissions, while "revitalising" parts of the NHS estate, and ensuring continuity of vital hospital services for facilities managers.

  17. Evaluating direct energy savings and market transformation effects: A decade of technical design assistance in the northwestern USA

    International Nuclear Information System (INIS)

    Van Den Wymelenberg, Kevin; Brown, G.Z.; Burpee, Heather; Djunaedy, Ery; Gladics, Gunnar; Kline, Jeff; Loveland, Joel; Meek, Christopher; Thimmanna, Harshana

    2013-01-01

    This paper documents the direct energy savings and energy efficiency market transformation impacts of a multi-state design assistance program in the northwestern US. The paper addresses four specific aims. (1) It provides a conservative and justified estimate of the direct energy savings associated with design assistance activities of a market transformation program from 2001 to 2010. (2) It provides a rigorous methodology to evaluate direct energy savings associated with design assistance market transformation programs. (3) It provides a low-cost replicable method to predict energy savings in new buildings by evaluating the integrated design process. (4) It provides quantitative indicators useful for estimating indirect energy savings from market transformation. Applying the recommended analysis method and assuming a 12-year measure life, the direct energy savings of the population (626 buildings; 51,262,000 ft 2 ) is estimated as 45.3 aMW (average megawatts) (electric), and 265,738.089 therms (non-electric). If the entire program budget were divided into the electric savings only, the Lab Network cost per kWh saved ranged from $0.0016 to $0.003 using the recommended method and $0.0092/kWh using the most conservative method. These figures do not isolate contextual influences or represent total resource cost. Statistically significant correlations (r 2 =0.1−0.3) between integrated design scores and energy savings are reported. - Highlights: ► Estimated direct energy savings of a market transformation program are presented. ► A methodology to evaluate energy savings from multiple baselines is documented. ► Level of integrated design can be used to estimate energy savings in new buildings. ► Quantitative evaluation indicators of efficiency market transformation are provided. ► Electric energy saved from design assistance costs between $0.0016 and $0.0092/kWh.

  18. The Three R's of Utility Savings: Rate Reduction, Rebates and Retrofit.

    Science.gov (United States)

    Petiunas, Raymond V.

    1993-01-01

    An effective way to increase electricity energy savings for school districts is to integrate rate case participation (rate reduction) with conservation and load-management efforts (rebates) and retrofit operations, to obtain a total energy cost reduction package. Describes how a Pennsylvania consortium of school districts saved its member…

  19. A Quantification of the Energy Savings by Conservation Voltage Reduction

    NARCIS (Netherlands)

    Ellens, W.; Berry, A.; West, S.

    2013-01-01

    The introduction of `Smart grid' technologies in the electricity supply industry has attracted new attention to Conservation Voltage Reduction (CVR). CVR is a method that aims to save energy by reducing the voltage level of the electrical distribution network. However, not all devices consume less

  20. Chapter 10: Peak Demand and Time-Differentiated Energy Savings Cross-Cutting Protocol. The Uniform Methods Project: Methods for Determining Energy Efficiency Savings for Specific Measures

    Energy Technology Data Exchange (ETDEWEB)

    Kurnik, Charles W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Stern, Frank [Navigant, Boulder, CO (United States); Spencer, Justin [Navigant, Boulder, CO (United States)

    2017-10-03

    Savings from electric energy efficiency measures and programs are often expressed in terms of annual energy and presented as kilowatt-hours per year (kWh/year). However, for a full assessment of the value of these savings, it is usually necessary to consider the measure or program's impact on peak demand as well as time-differentiated energy savings. This cross-cutting protocol describes methods for estimating the peak demand and time-differentiated energy impacts of measures implemented through energy efficiency programs.

  1. Effect of daylight saving time on lighting energy use: a literature review

    NARCIS (Netherlands)

    Aries, M.B.C.; Newsham, G.R.

    2008-01-01

    The principal reason for introducing (and extending) daylight saving time (DST) was, and still is, projected energy savings, particularly for electric lighting. This paper presents a literature review concerning the effects of DST on energy use. Simple estimates suggest a reduction in national

  2. Year-round daylight saving time will save more energy in India than corresponding DST or time zones

    International Nuclear Information System (INIS)

    Ahuja, Dilip R.; SenGupta, D.P.

    2012-01-01

    Many countries have experimented with daylight saving time (DST) to save energy and to align human activities more closely to the daily cycle of light and darkness. Using a novel methodology, we estimate the year-round energy savings to be obtained from advancing Indian Standard Time (IST), from the introduction of DST, and from dividing the country into two time zones. We find that the option of advancing IST consistently saves more energy than the corresponding DST option, which in turn saves more energy than the corresponding time zones option. This is because the energy benefits of advancing IST accrue for the entire year throughout the country, whereas the benefits of DST are confined to summer months and the benefits of two time zones are largely in the lower energy consuming eastern region. We recommend advancing IST by half-hour to being six hours ahead of UTC. This confers the advantages of DST and time zones without their disadvantages and is forecast to save more than 2 billion kWh of electricity every year during evening peaks that are difficult to supply. While these results are India-specific, similar exercises would be useful to many other countries. - Highlights: ► Advancing IST (YRDST) consistently saves more energy than the corresponding DST. ► DST consistently saves more energy than dividing India into two time zones. ► There are also many non-energy benefits of advancing IST. ► Results are for India; countries with DST may find it useful to consider YRDST.

  3. Implementation of energy-saving policies in China: How local governments assisted industrial enterprises in achieving energy-saving targets

    International Nuclear Information System (INIS)

    Zhao, Xiaofan; Li, Huimin; Wu, Liang; Qi, Ye

    2014-01-01

    Local governments have replaced the national ministries that are in charge of various industries to become the primary implementer of energy-saving policies in China since 2000. This paper employs a case study-based approach to demonstrate the significance of local governments’ policy measures in assisting industrial enterprises with energy-saving activities in China. Based on the longitudinal case of the Jasmine Thermal Electric Power Company, this paper hypothesizes that sub-national governments have played a major role in implementing energy-saving policies in China since the 11th Five-year-plan period. A wide range of provincial and municipal agencies collaborated in implementing five types of policy measures – informational policy, skill building, improved enforcement of central directives, price adjustment, and funding – that reduced barriers to energy saving and motivated active pursuit of energy-saving activities at industrial enterprises. The case study demonstrates how an enterprise and local governments work together to achieve the enterprise's energy-saving target. The authors will investigate the hypothesis of this paper in the context of multiple case studies that they plan to undertake in the future. - Highlights: • We employ a case study-based approach to study policy implementation in China. • Local governments have played a major role in implementing energy-saving policies. • Local public agencies collaborated in implementing five types of policy measures. • Local policy measures reduced barriers to energy saving at industrial enterprises. • Enterprises and local governments work together to achieve energy-saving targets

  4. Projects of electrical energy saving in Costa Rica; Proyectos de ahorro de energia electrica en Costa Rica

    Energy Technology Data Exchange (ETDEWEB)

    Chinchilla, Henry [Compania Nacional de Luz y Fuerza, S.A., San Jose (Costa Rica)

    1999-07-01

    Costa Rica, located in Central America, is a highly electrified country, more of the 93.6% of the population, has access to the electricity, and its load curve presents two important demand peaks, one of them near noon and another one at sundown, additionally, the growth of this service is important, reason why it has been oriented to the establishment of actions focussed to the better use of the energy, in special of the electricity. The following notes are intended to show briefly the origin of the actions oriented to the energy saving, identifying the main projects that marked an important track in the national development in this sense, as well as a sample of some of the projects which have permitted to maintain throughout the last decade of this century a permanent attitude on the promotion and education of the saving and handling of the energy demand, specially of electricity, of such a way as to a suitable contribution is achieved towards the industrial competitiveness, human comfort and environmental protection. [Spanish] Costa Rica, ubicado en la America Central, es un pais altamente electrificado, mas del 93.6% de la poblacion, tiene acceso a la electricidad, y su curva de carga presenta dos importantes picos de demanda uno cercano al medio dia y otro al ocultarse el sol, junto a ello el crecimiento este servicio es importante, por lo que se ha abocado a establecer acciones que se orientan al mejor uso de la energia, en especial de la electricidad. En las siguientes notas se trata de mostrar en forma breve el origen de las acciones orientadas al ahorro de energia, identificando los principales proyectos que marcaron una huella importante en el rumbo nacional en este sentido, asi como una muestra de algunos de los proyectos que han permitido mantener a lo largo de la ultima decada de este siglo una permanente actitud de la promocion y ensenanza del ahorro y manejo de la demanda de energia, en especial de la electricidad, de tal forma que se logre con ello

  5. Ecology: Electrical Cable Bacteria Save Marine Life

    DEFF Research Database (Denmark)

    Nielsen, Lars Peter

    2016-01-01

    Animals at the bottom of the sea survive oxygen depletion surprisingly often, and a new study identifies cable bacteria in the sediment as the saviors. The bacterial electrical activity creates an iron 'carpet', trapping toxic hydrogen sulfide.......Animals at the bottom of the sea survive oxygen depletion surprisingly often, and a new study identifies cable bacteria in the sediment as the saviors. The bacterial electrical activity creates an iron 'carpet', trapping toxic hydrogen sulfide....

  6. C. h. p. saves fuel in Sweden

    Energy Technology Data Exchange (ETDEWEB)

    Daugas, C F

    1979-04-01

    A combined heat and power plant based on a diesel generator to produce 12MW of electricity and 12MW of heat has successfully supplied the town of Skultuna in Sweden during the winter and has saved 3,700t of oil annually.

  7. Application of Waste Heat Recovery Energy Saving Technology in Reform of UHP-EAF

    Science.gov (United States)

    Zhao, J. H.; Zhang, S. X.; Yang, W.; Yu, T.

    2017-08-01

    The furnace waste heat of a company’s existing 4 × 100t ultra-high-power electric arc furnaces is not used and discharged directly of the situation has been unable to meet the national energy-saving emission reduction requirements, and also affected their own competitiveness and sustainable development. In order to make full use of the waste heat of the electric arc furnace, this paper presents an the energy-saving transformation program of using the new heat pipe boiler on the existing ultra-high-power electric arc furnaces for recovering the waste heat of flue gas. The results show that after the implementation of the project can save energy equivalent to 42,349 tons of standard coal. The flue gas waste heat is fully utilized and dust emission concentration is accorded with the standard of Chinese invironmental protection, which have achieved good results.

  8. Electricity savings in Latvia through implementation of labelling directives. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    Legislation on labelling of household appliances was enforced in Latvia July 2001 to implement the European labelling directives. The project 'Electricity Savings in Latvia through Implementation of labelling Directives' was started January 2001 in order to support the implementation of the directives to ensure that they got an immediate effect. The project has included the following activities: Information of the general public and of traders and importers. In relation to the general public the activities consisted of production of a widely spread information brochure, TV-spots and a TV competition and participation in a school project. Seminars and meetings with traders and importers were held to inform about the legislation before it was enforced and to create a network for discussion of practical implementation problems and planning of the information activities. Test and control activities. The purpose of the test and control activities was to strengthen the test and control capacities and to transfer experience from Denmark. This was achieved though workshops for as well inspectors from the Consumer Rights Protection Centre and for members of the voluntary Consumer Protection Clubs. Results: It is assumed that the project has been very successful in the sense that the information about labelling of appliances has been efficiently spread via the information brochure, which was printed in 100.000 copies and distributed in shops, via Latvenergo and the consumer clubs. Furthermore, a cartoon about 'Energy-eaters' produced as part of the project by a very talented Latvian film study (Environmental Film Studio) has been used as TV-spot and has been broadcasted 40 times, including in connection to a morning TV-competition on labelling of appliances. The participatory approach used in the project has resulted in a very dedicated participation from the different stake holders side. Thus there is basis for sustainability in the sense, that a network

  9. The influences of financial and non-financial factors on energy-saving behaviour: A field experiment in Japan

    International Nuclear Information System (INIS)

    Mizobuchi, Kenichi; Takeuchi, Kenji

    2013-01-01

    This study examines the influences of financial and non-financial factors on electricity-conservation behaviour. A random sample of 236 Japanese households participated in the field experiment and the participants were offered two interventions, such as monetary rewards, depending on their reduction in electricity consumption and comparative feedback. The average saving rates of the (i) reward-intervention group (5.9%) and the (ii) reward with comparative feedback group (8.2%) are statistically larger than those of the (iii) control group (1.7%). Our study demonstrates the following. First, our econometric analysis confirmed a significant response by households to financial incentives but a more inconclusive response to the treatment that provided non-financial, additional information. Second, we found a positive influence of treatment externalities across time and households on energy saving. Third, there is a heterogeneous treatment effect in the reward-intervention group, with the households having a high New Ecological Paradigm (NEP) score being more likely to respond to the reward programme and save electricity than those that do not. Finally, and most interestingly, differences in responses to the questionnaire before and after the experiment suggest that the participants had underestimated the marginal costs of saving electricity before they actually started to do so. - highlights: • We studied the effects of (non-)financial factors on household electricity use. • Financial factors had a significant effect; non-financial ones were inconclusive. • Externalities had a positive effect across time and households on saving energy. • There is a heterogeneous treatment effect in financial-reward intervention. • Before the experiment, participants underestimated the marginal costs of saving electricity

  10. Electricity and Sustainability

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen

    1998-01-01

    This invited presentation first deals with the potentials and environmantal advantages of reducing electricity demand. The policies for implementing these savings are dicussed and proposal for future strategies are suggested. The mephasis is on the conflicts between a free European trade with ele......This invited presentation first deals with the potentials and environmantal advantages of reducing electricity demand. The policies for implementing these savings are dicussed and proposal for future strategies are suggested. The mephasis is on the conflicts between a free European trade...

  11. Energy savings assessment for digital-to-analog converter boxes

    International Nuclear Information System (INIS)

    Cheung, Hoi Ying; Meier, Alan; Brown, Richard

    2011-01-01

    The Digital Television (DTV) Converter Box Coupon Program was administered by the U.S. government to subsidize purchases of digital-to-analog converter boxes, with up to two $40 coupons for each eligible household. In order to qualify as Coupon Eligible Converter Boxes (CECBs), these devices had to meet a number of minimum performance specifications, including energy efficiency standards. The Energy Star Program also established voluntary energy efficiency specifications that are more stringent than the CECB requirements. In this study, we measured the power and energy consumptions for a sample of 12 CECBs (including 6 Energy Star labeled models) in-use in homes and estimated aggregate energy savings produced by the energy efficiency policies. Based on the 35 million coupons redeemed through the end of the program, our analysis indicates that between 2500 and 3700 GWh per year are saved as a result of the energy efficiency policies implemented on digital-to-analog converter boxes. The energy savings generated are equivalent to the annual electricity use of 280,000 average US homes. - Research highlights: → We examined energy efficiency policies on digital-to-analog converter boxes in US. → The government assistance program resulted in high participation. → 35 million coupons were redeemed for the purchases of energy efficient DTAs. → Between 2500 and 3700 GWh per year are saved as a result of the policies. → Savings are equivalent to the annual electricity use of 280,000 average US homes.

  12. Time-varying value of electric energy efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Mims, Natalie A.; Eckman, Tom; Goldman, Charles

    2017-06-30

    Electric energy efficiency resources save energy and may reduce peak demand. Historically, quantification of energy efficiency benefits has largely focused on the economic value of energy savings during the first year and lifetime of the installed measures. Due in part to the lack of publicly available research on end-use load shapes (i.e., the hourly or seasonal timing of electricity savings) and energy savings shapes, consideration of the impact of energy efficiency on peak demand reduction (i.e., capacity savings) has been more limited. End-use load research and the hourly valuation of efficiency savings are used for a variety of electricity planning functions, including load forecasting, demand-side management and evaluation, capacity and demand response planning, long-term resource planning, renewable energy integration, assessing potential grid modernization investments, establishing rates and pricing, and customer service. This study reviews existing literature on the time-varying value of energy efficiency savings, provides examples in four geographically diverse locations of how consideration of the time-varying value of efficiency savings impacts the calculation of power system benefits, and identifies future research needs to enhance the consideration of the time-varying value of energy efficiency in cost-effectiveness screening analysis. Findings from this study include: -The time-varying value of individual energy efficiency measures varies across the locations studied because of the physical and operational characteristics of the individual utility system (e.g., summer or winter peaking, load factor, reserve margin) as well as the time periods during which savings from measures occur. -Across the four locations studied, some of the largest capacity benefits from energy efficiency are derived from the deferral of transmission and distribution system infrastructure upgrades. However, the deferred cost of such upgrades also exhibited the greatest range

  13. Electricity savings with pellet stoves and solar heating in electrically heated houses; Elbesparing med pelletkaminer och solvaerme i direktelvaermda smaahus

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Tomas [Hoegskolan Dalarna, Borlaenge (Sweden)

    2004-07-01

    The aim of this study was to investigate how electrically heated houses can be converted to using wood pellet and solar heating. There are a large number of wood pellet stoves on the market. Many stoves have a water jacket, which gives an opportunity to distribute the heat to domestic hot water and a radiator heating system. Three typical Swedish houses with electric resistance heating have been studied. Fourteen different system concepts using wood pellet stoves and solar heating systems have been evaluated. The systems and the houses have been simulated in detail using TRNSYS. The houses have been divided in up to 10 different zones and heat transfer by air circulation through doorways and open doors have been simulated. The pellet stoves were simulated using a recently developed TRNSYS component, which models the start- and stop phases, emissions and the dynamic behaviour of the stoves. The model also calculates the CO-emissions. Simulations were made with one stove without a water jacket and two stoves with different fractions of the generated heat distributed in the water circuit. Simulations show that the electricity savings using a pellet stove are greatly affected by the house plan, the system choice, if the internal doors are open or closed and the desired level of comfort. Installing a stove with a water-jacket connected to a radiator system and a hot water storage has the advantage that heat can be transferred to domestic hot water and be distributed to other rooms. Such systems lead to greater electricity savings, especially in houses having a traditional layout. It was found that not all rooms needed radiators and that it was more effective in most cases to use a stove with a higher fraction of the heat distributed by the water circuit. The economic investigation shows that installing a wood pellet stove without a water jacket gives the lowest total energy- and capital costs in the house with an open plan (for today's energy prices and the

  14. Chinese hotel general managers' perspectives on energy-saving practices

    Science.gov (United States)

    Zhu, Yidan

    As hotels' concern about sustainability and budget-control is growing steadily, energy-saving issues have become one of the important management concerns hospitality industry face. By executing proper energy-saving practices, previous scholars believed that hotel operation costs can decrease dramatically. Moreover, they believed that conducting energy-saving practices may eventually help the hotel to gain other benefits such as an improved reputation and stronger competitive advantage. The energy-saving issue also has become a critical management problem for the hotel industry in China. Previous research has not investigated energy-saving in China's hotel segment. To achieve a better understanding of the importance of energy-saving, this document attempts to present some insights into China's energy-saving practices in the tourist accommodations sector. Results of the study show the Chinese general managers' attitudes toward energy-saving issues and the differences among the diverse hotel managers who responded to the study. Study results indicate that in China, most of the hotels' energy bills decrease due to the implementation of energy-saving equipments. General managers of hotels in operation for a shorter period of time are typically responsible for making decisions about energy-saving issues; older hotels are used to choosing corporate level concerning to this issue. Larger Chinese hotels generally have official energy-saving usage training sessions for employees, but smaller Chinese hotels sometimes overlook the importance of employee training. The study also found that for the Chinese hospitality industry, energy-saving practices related to electricity are the most efficient and common way to save energy, but older hotels also should pay attention to other ways of saving energy such as water conservation or heating/cooling system.

  15. Energy-Efficiency Policy Opportunities for Electric Motor-Driven Systems

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    This publication is the first global analysis of energy consumption and energy efficiency potential of EMDS (electric motor- driven system). The electric motors and systems they drive are the largest single electricity end use, accounting for more than 40% of global electricity consumption. Huge energy efficiency potential was found untapped in EMDS - around 25% of EMDS electricity use could be saved cost-effectively, reducing total global electricity demand by about 10%. However, the energy efficiency of EMDS has been relatively neglected in comparison with other sustainable energy opportunities. It is crucial to scale up the operations and resources committed to realizing the vast savings potential of optimized EMDS. This paper proposes a comprehensive package of policy recommendations to help governments realize the potential for energy savings in EMDS.

  16. The energy saving manual; Das Energiesparbuch

    Energy Technology Data Exchange (ETDEWEB)

    Goetze, Monika; Pinn, Gudrun

    2009-07-01

    The constant increase in the cost of electric power, petroleum, gasoline and gas burden the household budget. At the same time, greenhouse gases are speeding up global warming alarmingly. It is time to reconsider our style of living. This guide presents simple and practical hints to reduce energy costs and protect the climate. Exemplary calculations show how up to 1100 Euro can be saved per household member and per annum. Subjects: Identifying fields of excess energy consumption; No wasting of electricity, heat, and warm water; Food, shopping and climate; Mobility and climate protection; How to establish an individual energy conservation profile. (orig.)

  17. Energy Saving in Data Processing and Communication Systems

    Directory of Open Access Journals (Sweden)

    Giuseppe Iazeolla

    2014-01-01

    Full Text Available The power management of ICT systems, that is, data processing (Dp and telecommunication (Tlc systems, is becoming a relevant problem in economical terms. Dp systems totalize millions of servers and associated subsystems (processors, monitors, storage devices, etc. all over the world that need to be electrically powered. Dp systems are also used in the government of Tlc systems, which, besides requiring Dp electrical power, also require Tlc-specific power, both for mobile networks (with their cell-phone towers and associated subsystems: base stations, subscriber stations, switching nodes, etc. and for wired networks (with their routers, gateways, switches, etc.. ICT research is thus expected to investigate into methods to reduce Dp- and Tlc-specific power consumption. However, saving power may turn into waste of performance, in other words, into waste of ICT quality of service (QoS. This paper investigates the Dp and Tlc power management policies that look at compromises between power saving and QoS.

  18. Impact of daylight saving time on the Chilean residential consumption

    International Nuclear Information System (INIS)

    Verdejo, Humberto; Becker, Cristhian; Echiburu, Diego; Escudero, William; Fucks, Emiliano

    2016-01-01

    Since 1970 Chile has had a Daylight Saving Time (DST) policy in order to reduce residential electricity consumption in the country. The time change was set for the first time by executive decree in 1970, and since that date it was applied every year without great changes until 2010. Since then, and to date, decrees have been set in order to increase the duration of the DST, arguing that there are reasons associated with energy savings that justify the extension of the measure that has been adopted by the authority in recent years. In the present study the impact of the application of DST in terms of decreased household electricity consumption is analyzed using two complementary methods, one based on a heuristic approach and the other using an econometric model. The results indicate that there is indeed a marginally small reduction in residential electricity consumption, although these results are not homogeneous throughout the country. - Highlights: • The impact of the application of DST is analyzed in Chilean distribution networks. • The results indicate that there is indeed a marginally small reduction in residential electricity consumption. • A total energy reduction is estimated based on the proposed methodology.

  19. Locomotive energy savings possibilities

    Directory of Open Access Journals (Sweden)

    Leonas Povilas LINGAITIS

    2009-01-01

    Full Text Available Economic indicators of electrodynamic braking have not been properly estimated. Vehicles with alternative power trains are transitional stage between development of pollution- free vehicles. According to these aspects the investigation on conventional hybrids drives and their control system is carried out in the article. The equation that allows evaluating effectiveness of regenerative braking for different variants of hybrid drive are given. Presenting different types of locomotive energy savings power systems, which are using regenerative braking energy any form of hybrid traction vehicles systems, circuit diagrams, electrical parameters curves.

  20. Exploring Demand Charge Savings from Commercial Solar

    Energy Technology Data Exchange (ETDEWEB)

    Darghouth, Naim [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Barbose, Galen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Mills, Andrew [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wiser, Ryan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gagnon, Pieter [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bird, Lori [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-07-31

    Commercial retail electricity rates commonly include a demand charge component, based on some measure of the customer’s peak demand. Customer-sited solar PV can potentially reduce demand charges, but the magnitude of these savings can be difficult to predict, given variations in demand charge designs, customer loads, and PV generation profiles. Moreover, depending on the circumstances, demand charges from solar may or may not align well with associated utility cost savings. Lawrence Berkeley National Laboratory (Berkeley Lab) and the National Renewable Energy Laboratory (NREL) are collaborating in a series of studies to understand how solar PV can reduce demand charge levels for a variety of customer types and demand charges designs. Previous work focused on residential customs with solar. This study, instead, focuses on commercial customers and seeks to understand the extent and conditions under which rooftop can solar reduce commercial demand charges. To answer these questions, we simulate demand charge savings for a broad range of commercial customer types, demand charge designs, locations, and PV system characteristics. This particular analysis does not include storage, but a subsequent analysis in this series will evaluate demand charge savings for commercial customers with solar and storage.

  1. China energy-water nexus: Assessing the water-saving synergy effects of energy-saving policies during the eleventh Five-year Plan

    International Nuclear Information System (INIS)

    Gu, Alun; Teng, Fei; Wang, Yu

    2014-01-01

    Highlights: • Energy and water limit China’s sustainable development. • Current energy policies fail to address water saving issues. • The energy-water coefficient is estimated for both direct use and indirect use. • Water saving effects associated with energy-saving policies is calculated. • Water-energy nexus should be enhanced in key industrial sectors. - Abstract: Energy and water have become major factors limiting sustainable development in China. Energy efficiency and optimization of water management are critical for the healthy growth of the Chinese economy. Current national energy policies fail to adequately address water use issues. Similarly, current water policies do not consider the impact of energy consumption and greenhouse gas emissions. Consequently, few studies have investigated the relationship between energy consumption and water use. The present study analyzes the energy-water nexus in Chinese industries using input–output tables. Coefficients that characterize the relationship between energy consumption and water are used to describe the supply-consumption relationship between the water supply and primary energy sectors. Next, we calculate the water-saving effects associated with the enforcement of energy-saving policies in selected industrial sectors during the eleventh Five-year Plan, from 2005 to 2010. These calculations address the ferrous metals, non-ferrous metals, petrochemical engineering, building materials, and electricity industries as well as key light industries. Our findings indicate that energy-saving efforts in these industries will result in savings in water consumption. This study suggests that a cooperative relationship between water and energy conservation efforts should be an important factor in creating policies that encourage simultaneous savings of both resources. Additionally, the study indicates that government should promote water- and energy-saving techniques in key industrial sectors to encourage

  2. Targeting utility customers to improve energy savings from conservation and efficiency programs

    International Nuclear Information System (INIS)

    Taylor, Nicholas W.; Jones, Pierce H.; Kipp, M. Jennison

    2014-01-01

    Highlights: • Improving DSM program impacts by targeting high energy users. • DSM energy savings potential hinges on pre-participation performance. • Targeting can benefit different utilities and energy efficiency programs. • Overall performance can be improved by up to 250% via targeting strategies. - Abstract: Electric utilities, government agencies, and private interests in the US have committed and continue to invest substantial resources – including billions of dollars of financial capital – in the pursuit of energy efficiency and conservation through demand-side management (DSM) programs. While most of these programs are deemed to be cost effective, and therefore in the public interest, opportunities exist to improve cost effectiveness by targeting programs to those customers with the greatest potential for energy savings. This article details an analysis of three DSM programs offered by three Florida municipal electric utilities to explore such opportunities. First, we estimate programs’ energy savings impacts; second, we measure and compare energy savings across subgroups of program participants as determined by their pre-intervention energy performance, and third, we explore potential changes in program impacts that might be realized by targeting specific customers for participation in the DSM programs. All three programs resulted in statistically significant average (per-participant) energy savings, yet average savings varied widely, with the customers who performed best (i.e., most efficient) before the intervention saving the least energy and those who performed worst (i.e., least efficient) before the intervention saving the most. Assessment of alternative program participation scenarios with varying levels of customer targeting suggests that program impacts could be increased by as much as 80% for a professional energy audit program, just over 100% for a high-efficiency heat pump upgrade program, and nearly 250% for an attic insulation

  3. Median nerve fascicular anatomy as a basis for distal neural prostheses.

    Science.gov (United States)

    Planitzer, Uwe; Steinke, Hanno; Meixensberger, Jürgen; Bechmann, Ingo; Hammer, Niels; Winkler, Dirk

    2014-05-01

    Functional electrical stimulation (FES) serves as a possible therapy to restore missing motor functions of peripheral nerves by means of cuff electrodes. FES is established for improving lower limb function. Transferring this method to the upper extremity is complex, due to a lack of anatomical data on the physiological configuration of nerve fascicles. Our study's aim was to provide an anatomical basis for FES of the median nerve in the distal forearm and hand. We investigated 21 distal median nerves from 12 body donors. The peripheral fascicles were traced back by removing the external and interfascicular epineurium and then assigned to 4 quadrants. A distinct motor and sensory distribution was observed. The fascicles innervating the thenar eminence and the first lumbrical muscle originated from the nerves' radial parts in 82%. The fascicle supplying the second lumbrical muscle originated from the ulnar side in 78%. No macroscopically visible plexus formation was observed for the distal median nerve in the forearm. The findings on the distribution of the motor branches of the median nerve and the missing plexus formation may likely serve as an anatomical basis for FES of the distal forearm. However, due to the considerable variability of the motor branches, cuff electrodes will need to be adapted individually in FES. Taking into account the sensory distribution of the median nerve, FES may also possibly be applied in the treatment of regional pain syndromes. Copyright © 2013 Elsevier GmbH. All rights reserved.

  4. Energy conservation in electric distribution

    International Nuclear Information System (INIS)

    Lee, Chong-Jin.

    1994-01-01

    This paper discusses the potential for energy and power savings that exist in electric power delivery systems. These savings translate into significant financial and environmental benefits for electricity producers and consumers as well as for society in general. AlliedSignal's knowledge and perspectives on this topic are the result of discussions with hundreds of utility executives, government officials and other industry experts over the past decade in conjunction with marketing our Amorphous Metal technology for electric distribution transformers. Amorphous metal is a technology developed by AlliedSignal that significantly reduces the energy lost in electric distribution transformers at an incremental cost of just a few cents per kilo-Watt-hour. The purpose of this paper is to discuss: Amorphous Metal Alloy Technology; Energy Savings Opportunity; The Industrial Barriers and Remedies; Worldwide Demand; and A Low Risk Strategy. I wish this presentation will help KEPCO achieve their stated aims of ensuring sound development of the national economy and enhancement of public life through the economic and stable supply of electric power. AlliedSignal Korea Ltd. in conjunction with AlliedSignal Amorphous Metals in the U.S. are here to work with KEPCO, transformer manufacturers, industry, and government agencies to achieve greater efficiency in power distribution

  5. Potential electricity savings by variable speed control of compressor for air conditioning systems

    Energy Technology Data Exchange (ETDEWEB)

    Nasution, Henry [Bung Hatta University, Department of Mechanical Engineering, Faculty of Industrial Engineering, Padang, West Sumatera (Indonesia); Wan Hassan, Mat Nawi [Universiti Teknologi Malaysia, Faculty of Mechanical Engineering, Skudai, Johor Bahru-Darul Ta' zim (Malaysia)

    2006-05-15

    The potential of a variable-speed compressor running on a controller to provide enhanced load-matching capability, energy saving and thermal comfort for application in air-conditioning system is demonstrated. An air-conditioning system, originally operated on a constant speed mode, is retrofitted with an inverter and a PID controller. The system was installed to a thermal environmental room together with a data acquisition system to monitor energy consumption and temperature of the room. Measurements were taken 2 h daily at a time interval of 5 min for an on/off and an inverter variable-speed conditions. The results indicate that thermal comfort of the room together with energy saving can be obtained through a proper selection of K for the controller. At a temperature setting of 22 C, the energy saving for the system is estimated to reach 25.3% for PID controllers. (orig.)

  6. Estimated incident cost savings in shipping due to inspections.

    Science.gov (United States)

    Knapp, Sabine; Bijwaard, Govert; Heij, Christiaan

    2011-07-01

    The effectiveness of safety inspections of ships has been analysed from various angles, but until now, relatively little attention has been given to translate risk reduction into incident cost savings. This paper provides a monetary quantification of the cost savings that can be attributed to port state control inspections and industry vetting inspections. The dataset consists of more than half a million ship arrivals between 2002 and 2007 and contains inspections of port state authorities in the USA and Australia and of three industry vetting regimes. The effect of inspections in reducing the risk of total loss accidents is estimated by means of duration models, in terms of the gained probability of survival. The monetary benefit of port state control inspections is estimated to range, on average, from about 70 to 190 thousand dollars, with median values ranging from about 20 to 45 thousand dollars. Industry inspections have even higher benefits, especially for tankers. The savings are in general higher for older and larger vessels, and also for vessels with undefined flag and unknown classification society. As inspection costs are relatively low in comparison to potential cost savings, the results underline the importance of determining ships with relatively high risk of total loss. Copyright © 2011 Elsevier Ltd. All rights reserved.

  7. Sosiaalisen median mahdollisuudet Tilastokeskukselle

    OpenAIRE

    Vesterinen, Anu

    2011-01-01

    Tämän opinnäytetyön aiheena oli sosiaalisen median mahdollisuudet Tilastokeskuksen viestinnässä. Työn tavoitteena oli kartoittaa sosiaalisen median käyttöön liittyviä mahdollisuuksia ja haasteita sekä selvittää siihen liittyviä odotuksia Tilastokeskuksen henkilöstön keskuudessa. Työn teoriaosuudessa tarkasteltiin sosiaalista mediaa käsitteenä ja esiteltiin sosiaalisen median käyttöä organisaation ulkoisen viestinnän välineenä. Opinnäytetyössä selvitettiin teoriatietoon pohjautuen sekä ca...

  8. Comparison of all-electric secondary power systems for civil transport

    Science.gov (United States)

    Renz, David D.

    1992-01-01

    Three separate studies have shown operational, weight, and cost advantages for commercial subsonic transport aircraft using an all-electric secondary power system. The first study in 1982 showed that all-electric secondary power systems produced the second largest benefit compared to four other technology upgrades. The second study in 1985 showed a 10 percent weight and fuel savings using an all-electric high frequency (20 kHz) secondary power system. The last study in 1991 showed a 2 percent weight savings using today's technology (400 Hz) in an all-electric secondary power system. This paper will compare the 20 kHz and 400 Hz studies, analyze the 2 to 10 percent difference in weight savings and comment on the common benefits of the all-electric secondary power system.

  9. Efficiency trends in electric machines and drives

    International Nuclear Information System (INIS)

    Mecrow, B.C.; Jack, A.G.

    2008-01-01

    Almost all electricity in the UK is generated by rotating electrical generators, and approximately half of it is used to drive electrical motors. This means that efficiency improvements to electrical machines can have a very large impact on energy consumption. The key challenges to increased efficiency in systems driven by electrical machines lie in three areas: to extend the application of variable-speed electric drives into new areas through reduction of power electronic and control costs; to integrate the drive and the driven load to maximise system efficiency; and to increase the efficiency of the electrical drive itself. In the short to medium term, efficiency gains within electrical machines will result from the development of new materials and construction techniques. Approximately a quarter of new electrical machines are driven by variable-speed drives. These are a less mature product than electrical machines and should see larger efficiency gains over the next 50 years. Advances will occur, with new types of power electronic devices that reduce switching and conduction loss. With variable-speed drives, there is complete freedom to vary the speed of the driven load. Replacing fixed-speed machines with variable-speed drives for a high proportion of industrial loads could mean a 15-30% energy saving. This could save the UK 15 billion kWh of electricity per year which, when combined with motor and drive efficiency gains, would amount to a total annual saving of 24 billion kWh

  10. Renewable energy for Canada's northern communities - quantifying potential fuel savings

    International Nuclear Information System (INIS)

    Brothers, C.

    1998-01-01

    The probable impact of renewable energy technologies on fuel consumption in Canada's remote northern communities was discussed. These communities currently meet their electricity requirements using expensive diesel powered generators. It was noted that change to renewable energy in Canada's remote communities will only be made if the economic benefits can be clearly demonstrated. A study was conducted in Cambridge Bay, Northwest Territories, in which electrical load requirements and wind and solar resource data from the community was acquired to estimate savings in diesel fuel consumption for various renewable energy technologies. Wind was found to provide the most fuel displacement and was considered to be the most appropriate technology for these communities. A photovoltaic (PV) system of equivalent size would have significantly less impact on fuel savings in a community like Cambridge Bay, in part because a PV system would be poorly correlated on a seasonal basis with the energy requirements of the community. A wind-diesel system would be the most advantageous in terms of fuel savings due to its relatively high capacity factor, and due to the fact that is it is available year around. 4 refs., 1 tab., 4 figs

  11. Sosiaalisen median markkinointistrategia

    OpenAIRE

    Tran, Jenny

    2017-01-01

    Insinöörityön tavoitteena oli suunnitella toimeksiantajayritykselle sopiva sosiaalisen median markkinointistrategia ja avustaa sen toteutuksessa sekä tuottaen sisältöä sovittuihin kanaviin. Pyrkimyksenä oli myös kouluttaa yrityksen henkilökuntaa käyttämään sosiaalista mediaa yleisellä tasolla ja markkinoinnissa tutustuttamalla heidät sosiaalisen median erilaisiin kanaviin ja mainostyökaluihin. Opinnäytetyössä keskityttiin tutkimaan Facebookissa toimivaa markkinointia ja siinä toimivia mai...

  12. Cost of electricity generated and fuel saving of an optimized wind-diesel electricity supply for village in Tangier-area (Morocco)

    International Nuclear Information System (INIS)

    Nfaoui, H.; Buret, J.

    1996-01-01

    In several of the remote areas of Morocco, diesel generators are used to provide electrical power. Such systems are often characterized by poor efficiency and high maintenance costs. The integration of wind turbine with a diesel/battery hybrid system is becoming cost-effective in wind locations. In previous works (Nfaoul et al, 1990, 1994a, 1994b), the wind characteristics in Tangier-area were studied on the basis of 12 years (1978-1989) of hourly average wind speed data. A wind/diesel energy system with battery storage has been modelled using the Tangiers wind regime over a one year period (1989), and synthesized consumer load data based on the characteristics of typical usage of domestic appliances, along with the estimated working patterns of a local isolated community. In this work, we use a more realistic hourly consumer load, which is the result of an experiment realized in a Maroccan village using a diesel engine to provide electricity for lighting and audio-visual. The 1989 wind data were reworked for a large series of measurements (12 years). The optimum wind turbine size and the benefits of a storage system on fuel saving are also reviewed. This work is concerned with diesel fuel consumption: an optimum design of the considered system is to be found which minimises the cost energy generation over the equipments' lifetime. Given the economic assumption made (the most important being a fuel price of 4.5 Dh/litre and an interest rate of 5% net of inflation), the wind/diesel energy system has been shown to be competitive with diesel-only generation in the wind regime of the Tangier location for the cost per unit wind turbine swept area less than 3000 Dh/m 2 (8Dh=1$). (author)

  13. Energy Savings and Breakeven Costs for Residential Heat Pump Water Heaters in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Maguire, Jeff [National Renewable Energy Lab. (NREL), Golden, CO (United States); Burch, Jay [National Renewable Energy Lab. (NREL), Golden, CO (United States); Merrigan, Tim [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ong, Sean [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2013-07-01

    Heat pump water heaters (HPWHs) have recently re-emerged in the U.S. residential water heating market and have the potential to provide homeowners with significant energy savings. However, there are questions as to the actual performance and energy savings potential of these units, in particular in regards to the heat pump's performance in unconditioned space and the impact of the heat pump on space heating and cooling loads when it is located in conditioned space. To help answer these questions, NREL performed simulations of a HPWH in both conditioned and unconditioned space at over 900 locations across the continental United States and Hawaii. Simulations included a Building America benchmark home so that any interaction between the HPWH and the home's HVAC equipment could be captured. Comparisons were performed to typical gas and electric water heaters to determine the energy savings potential and cost effectiveness of a HPWH relative to these technologies. HPWHs were found to have a significant source energy savings potential when replacing typical electric water heaters, but only saved source energy relative to gas water heater in the most favorable installation locations in the southern United States. When replacing an electric water heater, the HPWH is likely to break even in California, the southern United States, and parts of the northeast in most situations. However, the HPWH will only break even when replacing a gas water heater in a few southern states.

  14. Energy Savings and Breakeven Cost for Residential Heat Pump Water Heaters in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Maguire, J.; Burch, J.; Merrigan, T.; Ong, S.

    2013-07-01

    Heat pump water heaters (HPWHs) have recently reemerged in the U.S. residential water heating market and have the potential to provide homeowners with significant energy savings. However, there are questions as to the actual performance and energy savings potential of these units, in particular in regards to the heat pump's performance in unconditioned space and the impact of the heat pump on space heating and cooling loads when it is located in conditioned space. To help answer these questions, simulations were performed of a HPWH in both conditioned and unconditioned space at over 900 locations across the continental United States and Hawaii. Simulations included a Building America benchmark home so that any interaction between the HPWH and the home's HVAC equipment could be captured. Comparisons were performed to typical gas and electric water heaters to determine the energy savings potential and cost effectiveness of a HPWH relative to these technologies. HPWHs were found to have a significant source energy savings potential when replacing typical electric water heaters, but only saved source energy relative to gas water heater in the most favorable installation locations in the southern US. When replacing an electric water heater, the HPWH is likely to break even in California, the southern US, and parts of the northeast in most situations. However, the HPWH will only break even when replacing a gas water heater in a few southern states.

  15. Predictive Maintenance (PdM) Centralization for Significant Energy Savings

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Dale

    2010-09-15

    Cost effective predictive maintenance (PdM) technologies and basic energy calculations can mine energy savings form processes or maintenance activities. Centralizing and packaging this information correctly empowers facility maintenance and reliability professionals to build financial justification and support for strategies and personnel to weather global economic downturns and competition. Attendees will learn how to: Systematically build a 'pilot project' for applying PdM and tracking systems; Break down a typical electrical bill to calculate energy savings; Use return on investment (ROI) calculations to identify the best and highest value options, strategies and tips for substantiating your energy reduction maintenance strategies.

  16. Heat savings in energy systems with substantial distributed generation

    DEFF Research Database (Denmark)

    Østergaard, PA

    2003-01-01

    In Denmark, the integration of wind power is affected by a large amount of cogeneration of heat and power. With ancillary services supplied by large-scale condensation and combined heat and power (CHP) plants, a certain degree of large-scale generation is required regardless of momentary wind input......, if a certain production is required regardless of whether over-all electricity generation is sufficient. This article analyses this and although heat savings do have a negative impact on the amount of wind power the system may integrate a given moment in certain cases, associated fuel savings are notable...

  17. Comparison of all-electric secondary power systems for civil subsonic transports

    Science.gov (United States)

    Renz, David D.

    1992-01-01

    Three separate studies have shown operational, weight, and cost advantages for commercial subsonic transport aircraft using an all-electric secondary power system. The first study in 1982 showed that all-electric secondary power systems produced the second largest benefit compared to four other technology upgrades. The second study in 1985 showed a 10 percent weight and fuel savings using an all-electric high frequency (20 kHz) secondary power system. The last study in 1991 showed a 2 percent weight savings using today's technology (400 Hz) in an all-electric secondary power system. This paper will compare the 20 kHz and 400 Hz studies, analyze the 2 to 10 percent difference in weight savings and comment on the common benefits of the all-electric secondary power system.

  18. How Much Water Can We Save by Achieving Renewable Portfolio Standards in the Southwest United States?

    Directory of Open Access Journals (Sweden)

    Yuzhen Feng

    2018-03-01

    Full Text Available Electricity in the Southwestern United States is primarily generated with water intensive steam turbines. If energy demand continues to rise this will lead to a further rise in water demand. A comprehensive understanding of water consumption and withdrawal for utility scale generation of electricity is necessary before any improvements in the water efficiency of such systems in arid environments can be made. This study estimated and compared the water usage associated with thermoelectric generation (i.e., natural gas, coal, and solar energy, in the five driest Colorado River Basin states: Utah, New Mexico, Nevada, Arizona, and California. This study also examined and compared each state’s Renewable Portfolio Standards (RPS and how this might impact water savings. Results showed that each state’s current RPS goals would reduce the water that is consumed by the generation of electricity. However, the amount of water savings will vary on a state by state basis. In order to reduce water consumption, replacing thermal electric generation with photovoltaic (PV solar can be significant and should be encouraged. The amount of water saved will vary, however, depending on the state’s choice of coal or natural gas.

  19. Energy Savings Forecast of Solid-State Lighting in General Illumination Applications

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2014-08-29

    With declining production costs and increasing technical capabilities, LED adoption has recently gained momentum in general illumination applications. This is a positive development for our energy infrastructure, as LEDs use significantly less electricity per lumen produced than many traditional lighting technologies. The U.S. Department of Energy’s Energy Savings Forecast of Solid-State Lighting in General Illumination Applications examines the expected market penetration and resulting energy savings of light-emitting diode, or LED, lamps and luminaires from today through 2030.

  20. Ergonomics work stations decreases the health impairment and saves electrical energy at the woodworking workshop in Bali, Indonesia.

    Science.gov (United States)

    Sudiajeng, Lilik; Adiputra, Nyoman; Leibbrandt, Richard

    2012-12-01

    This research was conducted to assess the positive effect of the ergonomics work station on the health impairment and electrical energy usage at the woodworking workshop in Bali, Indonesia. Woodworking workshops are dangerous, particularly when they are used improperly. Workers are exposed to health hazards that cause health impairment and inefficiencies in their work conditions. A preliminary study at a woodworking workshop at the Bali State Polytechnic showed that the work station was not suitable to body size of the participants and caused awkward postures. In addition, there was also an inappropriate physical work environment. Both inappropriate work station and physical work environment caused participants to be less active and motivated. This paper reports on an experimental study into the effects of an ergonomic intervention at this workshop. The participants were 2 groups of male students with 10 participants in each group. The first group performed the task with the original work station as a control group, while the second group performed the task with the new work station. The study found a significant difference between groups (p work station decreased the working heart rate (16.7%), the total score of musculoskeletal disorders (17.3%), and the total score of psychological fatigue (21.5%). Furthermore, it also decreased the electrical energy usage (38.7%). This shows that an ergonomics intervention on work station decreased the health impairment and saved electrical energy usage. It also protected the workers from woodworking hazards and allowed participants to perform their tasks in healthy, safe, convenient and efficient work conditions.

  1. Energy savings in heating systems for nursery pigs; Uso racional de energia eletrica em sistema de aquecimento para creches de leitoes

    Energy Technology Data Exchange (ETDEWEB)

    Sarubbi, Juliana; Rossi, Luiz Antonio; Moura, Daniella Jorge de; Oliveira, Rafael Augustus de; David, Eduardo [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de de Engenharia Agricola], Emails: rossi@feagri.unicamp.br, daniella.moura@feagri.unicamp.br, augustus@feagri.unicamp.br

    2009-07-01

    Energy saving procedures in pig industry are important to bring sustainability to this economic activity. Energy savings can contribute to the economic and environmental feasibility of the livestock and improve animal welfare conditions. This research work aimed to perform a comparison among three heating technologies for nursery pigs related to the energy saving aspects. Three heating systems were studied: TR - suspended electrical resistors, TP - heated floor and TA - convection heating. The heated floor system was considered better than other under the aspect of electrical energy use. (author)

  2. A Pottery Electric Kiln Using Decompression

    Science.gov (United States)

    Naoe, Nobuyuki; Yamada, Hirofumi; Nakayama, Tetsuo; Nakayama, Minoru; Minamide, Akiyuki; Takemata, Kazuya

    This paper presents a novel type electric kiln which fires the pottery using the decompression. The electric kiln is suitable for the environment and the energy saving as the pottery furnace. This paper described the baking principle and the baking characteristic of the novel type electric kiln.

  3. Humidified micro gas turbines for domestic users: An economic and primary energy savings analysis

    International Nuclear Information System (INIS)

    Montero Carrero, Marina; De Paepe, Ward; Bram, Svend; Musin, Frédéric; Parente, Alessandro; Contino, Francesco

    2016-01-01

    Micro Gas Turbines (mGTs) offer valuable advantages for small-scale Combined Heat and Power (CHP) production compared to reciprocating Internal Combustion Engines (ICEs): lower maintenance costs per kWh_e, cleaner exhaust, lower vibration levels and concentration of the residual heat in a single source (the exhaust gases). Nevertheless, mGTs have lower electrical efficiencies, fact that has prevented them from penetrating in the CHP market. Hot liquid water injection—by means of a saturation tower within the micro Humid Air Turbine (mHAT) cycle—allows both improving the flexibility of heat production and the electrical efficiency of mGTs; two qualities that if enhanced would increase the economic feasibility of the technology. Although the advantages of mHAT technology have been proven from a thermodynamic point of view, its economic performance has not yet been fully investigated. This paper presents a comparison of the economic profitability and the primary energy savings of an mGT, an ICE and an mHAT unit operating in real network conditions. Our aim is to investigate whether the increase in flexibility and electrical efficiency, achieved when transforming an mGT into an mHAT, allows this technology to economically outperform ICEs. Results show that the three units are viable in scenarios with high electricity and low natural gas prices. For the cases in which investment is feasible, the revenues with mHAT are the highest: thanks to their flexibility in heat generation, mHAT units are able to run all year long. On the other hand, the greatest primary energy savings are achieved with ICE units—which have the highest overall efficiencies—while mHAT savings are substantially lower. - Highlights: • We analyse the economics and primary energy savings of an ICE, an mGT and an mHAT. • We consider hourly heat and electricity demand profiles and 25 price scenarios. • Our analysis is carried out for two domestic users with distinctive demand profiles. • If

  4. Blue Line Innovations brochure : Think green, act smart, save energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    Blue Line Innovations Inc. is working with leading electric utilities and regulatory agencies to provide smart-home technologies to consumers for demand-side management. Their latest product is the PowerCost Monitor, a real-time feedback product that help households understand and reduce the amount of electricity they use. The monitor, which reveals electricity use in real-time by both total and current cost and kilowatt hour, uses wireless encrypted technology to send usage information from an outside meter to an in-home display. The small detector/transmitter can be easily installed to an existing household electro-mechanical utility meter by the homeowner without an electrician or service disruption. Studies have shown that when domestic users are provided with real-time feedback on electricity usage, they can reduce their energy bills by as much as 20 per cent. This in-home measuring and reporting unit helps customers make decisions about changing their usage habits, purchasing electricity-saving light and appliances and conserving energy. In a demonstration project, Hydro-One installed PowerCost Monitors in the homes of Hydro One customers in Ontario in July 2004. The objective was to determine the extent of changes in customer behaviour and reductions in electricity consumption resulting from direct real-time feedback information on electricity consumption. Other demonstration projects have been launched in conjunction with CEA Technologies Inc., Natural Resources Canada, Newfoundland Power and BC hydro to install the monitors in homes on both coasts of Canada. Governments, utilities, communities and individuals are recognizing that saving energy is a critical factor to sustainable development by conserving natural resources and reducing pollution. A list of suggestions for reducing electricity use in lighting, kitchens, laundry and heating and cooling were also presented. 1 fig.

  5. My Home - analysis of the easy and intelligent way to save energy

    Energy Technology Data Exchange (ETDEWEB)

    Wilke, Goeran (The Danish Electricity Saving Trust (Denmark))

    2009-07-01

    The concept of the intelligent home is not new, but translating theory into reality presents many challenges. Launched in Denmark in October 2008, My Home is an interactive web portal offering consumers the opportunity to calculate their household energy consumption, receive advice on possible savings, and control and monitor their indoor environments by managing their energy consumption appropriately. This paper describes the software functionality of My Home and examines the energy saving benefits available to consumers who use this system to control and monitor electricity consumption in their homes. The paper further discusses the necessity of having a common infrastructure and standard for use by all producers and suppliers in order to ensure a mass market for compatible equipment and solutions. The analysis focuses on how My Home allows users to map energy consumption in their homes by using drag-and-drop icons to organise and equip a floorplan with their own electrical appliances. My Home features a calculator which automatically works out the annual electricity consumption and displays appropriate savings advice based on manually inputted readings or remote readings supplied by an electricity provider. Detailed statistical evaluation of metered values is also available. The extent to which the use of My Home has resulted in lower energy consumption in the homes of individual users is currently being determined by ongoing research. This involves examining users' motivations and needs, and testing for usability on the basis of ethnographic field work. The results showed that My Home facilitates easy configuration of home control and monitoring systems, which is normally very difficult to perform.

  6. National potential of saving of electricity in domestic refrigeration; Potencial nacional de ahorro de electricidad en refrigeracion domestica

    Energy Technology Data Exchange (ETDEWEB)

    Arroyo C, Fernando [Universidad Nacional Autonoma de Mexico (Mexico); Ambriz G, Juan Jose; Romero P, Hernando [Universidad Autonoma Metropolitana, (Mexico)

    2003-07-01

    In the present paper the evaluation of the potential of saving of electrical energy in Mexico is presented, by means of the substitution of old refrigerators of low efficiency by modern high efficiency ones. This potential is very ample, since the replacement of the old models by new follows a very slow curve, if the economic difficulties of the Mexican families are considered and that, on the other hand, the technology of the domestic refrigerators is so reliable that they have a very long life and they are not easily rejected. In field work have been found refrigerators operating with ages of more than 30 years and still 40. In Mexico, it is estimated that the refrigeration is responsible for around 29% of the of electricity consumption in homes settled in tempered climate and of 14 % in those of warm climate in which air conditioning is used. The proposal of this work is the organization of a governmental program of accelerated substitution of refrigerators that helps to acquire an efficient refrigerator and to reject the old ones. The results indicate that if a total renovation of the park of domestic refrigerators is made, the saving of electrical energy would reach the 5.2 TWh/a which represents the 44.5% of the total consumption of 11.7 TWh in a year. [Spanish] En el presente trabajo se presenta la evaluacion del potencial de ahorro de energia electrica en Mexico, mediante la substitucion de refrigeradores antiguos de baja eficiencia por modernos de alta eficiencia. Este potencial es muy amplio, ya que el reemplazo de los modelos viejos por nuevos sigue una curva muy lenta, si se consideran las dificultades economicas de las familias mexicanas y que, por otro lado, la tecnologia de los refrigeradores domesticos es tan confiable que tienen una vida muy larga y no se desechan facilmente. En trabajos de campo se han encontrado refrigeradores operando con edades de mas de 30 anos y aun 40. En Mexico, se estima que la refrigeracion es responsable de alrededor del

  7. Thrombosed persistent median artery causing carpal tunnel syndrome associated with bifurcated median nerve: A case report

    International Nuclear Information System (INIS)

    Salter, M.; Sinha, N. R.; Szmigielski, W.

    2011-01-01

    Background: Carpal tunnel syndrome is a sporadically occurring abnormality due to compression of median nerve. It is exceedingly rare for it to be caused by thrombosis of persistent median artery. Case Report: A forty two year old female was referred for ultrasound examination due to ongoing wrist pain, not relived by pain killers and mild paraesthesia on the radial side of the hand. High resolution ultrasound and Doppler revealed a thrombosed persistent median artery and associated bifurcated median nerve. The thrombus resolved on treatment with anticoagulants. Conclusions: Ultrasound examination of the wrist when done for patients with carpal tunnel syndrome should preferably include looking for persistent median artery and its patency. (authors)

  8. Household Savings

    DEFF Research Database (Denmark)

    Browning, Martin; Lusardi, Annamaria

    suggested in the informal saving literature can be captured in the standard optimizing model. Particular attention is given to recent work on the precautionary motive and its implications for saving and consumption behavior. We also discuss the "behavioral" or "psychological" approach that eschews the use......In this survey, we review the recent theoretical and empirical literature on household saving and consumption. The discussion is structured around a list of motives for saving and how well the standard theory captures these motives. We show that almost all of the motives for saving that have been...

  9. Energy-Saving Sintering of Electrically Conductive Powders by Modified Pulsed Electric Current Heating Using an Electrically Nonconductive Die

    Science.gov (United States)

    Ito, Mikio; Kawahara, Kenta; Araki, Keita

    2014-04-01

    Sintering of Cu and thermoelectric Ca3Co4O9 was tried using a modified pulsed electric current sintering (PECS) process, where an electrically nonconductive die was used instead of a conventional graphite die. The pulsed electric current flowed through graphite punches and sample powder, which caused the Joule heating of the powder compact itself, resulting in sintering under smaller power consumption. Especially for the Ca3Co4O9 powder, densification during sintering was also accelerated by this modified PECS process.

  10. Saving in cycles: how to get people to save more money.

    Science.gov (United States)

    Tam, Leona; Dholakia, Utpal

    2014-02-01

    Low personal savings rates are an important social issue in the United States. We propose and test one particular method to get people to save more money that is based on the cyclical time orientation. In contrast to conventional, popular methods that encourage individuals to ignore past mistakes, focus on the future, and set goals to save money, our proposed method frames the savings task in cyclical terms, emphasizing the present. Across the studies, individuals who used our proposed cyclical savings method, compared with individuals who used a linear savings method, provided an average of 74% higher savings estimates and saved an average of 78% more money. We also found that the cyclical savings method was more efficacious because it increased implementation planning and lowered future optimism regarding saving money.

  11. AutoPowerOff plug banks - a story with energy saving perspectives

    Energy Technology Data Exchange (ETDEWEB)

    Hjort Jensen, Anders (The Danish Electricity Saving Trust (Denmark)); Fjordbak, Troels (IT Energy ApS (Denmark))

    2009-07-01

    Denmark uses around 35 TWh of electricity per year, with residential dwellings accounting for around 10 TWh of this figure. Standby consumption comprises around 12% of power used in homes. If every Danish home installed AutoPowerOff plug banks, savings exceeding 500 GWh per year would be possible, equivalent to 5% of household electricity consumption, or 1.5% of the total in Denmark. This paper describes the estimated standby consumption in Danish homes in 2006, and possible energy savings through the use of AutoPowerOff plug banks. The estimates were subsequently used as background information for a 2007-2008 campaign to promote the wider use of these devices in Denmark. In order to increase the sale of AutoPowerOff plug banks by 1 million units, it was agreed that retail chains selling consumer electronics would include an AutoPowerOff when selling a TV or PC. A nationwide TV advertising campaign was launched featuring the names of participating retailers. Sales of AutoPowerOff plug banks in the first 7 months of 2008 passed the 515,000 mark, with over 1 million units now installed in 2.5 million Danish households. Annual savings are estimated to be over 80 GWh, equivalent to 40,000 tons of CO{sub 2}. This equates to potential savings on an EU-wide basis of more than 7 TWh, or 3.6 million tons of CO{sub 2} in Denmark.

  12. Economic analysis of electric heating based on critical electricity price

    Science.gov (United States)

    Xie, Feng; Sun, Zhijie; Zhou, Xinnan; Fu, Chengran; Yang, Jie

    2018-06-01

    The State Grid Corporation of China proposes an alternative energy strategy, which will make electric heating an important task in the field of residential electricity consumption. This article takes this as the background, has made the detailed introduction to the inhabitant electric heating technology, and take the Zhangjiakou electric panels heating technology as an example, from the expense angle, has carried on the analysis to the electric panels heating economy. In the field of residential heating, electric panels operating costs less than gas boilers. After customers implying energy-saving behavior, electric panels operating cost is even lower than coal-fired boilers. The critical price is higher than the execution price, which indicates that the economic performance of the electric panels is significantly higher than that of the coal boiler.

  13. A comparison of freeway median crash frequency, severity, and barrier strike outcomes by median barrier type.

    Science.gov (United States)

    Russo, Brendan J; Savolainen, Peter T

    2018-08-01

    Median-crossover crashes are among the most hazardous events that can occur on freeways, often resulting in severe or fatal injuries. The primary countermeasure to reduce the occurrence of such crashes is the installation of a median barrier. When installation of a median barrier is warranted, transportation agencies are faced with the decision among various alternatives including concrete barriers, beam guardrail, or high-tension cable barriers. Each barrier type differs in terms of its deflection characteristics upon impact, the required installation and maintenance costs, and the roadway characteristics (e.g., median width) where installation would be feasible. This study involved an investigation of barrier performance through an in-depth analysis of crash frequency and severity data from freeway segments where high-tension cable, thrie-beam, and concrete median barriers were installed. A comprehensive manual review of crash reports was conducted to identify crashes in which a vehicle left the roadway and encroached into the median. This review also involved an examination of crash outcomes when a barrier strike occurred, which included vehicle containment, penetration, or re-direction onto the travel lanes. The manual review of crash reports provided critical supplementary information through narratives and diagrams not normally available through standard fields on police crash report forms. Statistical models were estimated to identify factors that affect the frequency, severity, and outcomes of median-related crashes, with particular emphases on differences between segments with varying median barrier types. Several roadway-, traffic-, and environmental-related characteristics were found to affect these metrics, with results varying across the different barrier types. The results of this study provide transportation agencies with important guidance as to the in-service performance of various types of median barrier. Copyright © 2018 Elsevier Ltd. All rights

  14. Analisys and energy saving measures of kastvallen ice hockey rink arena

    OpenAIRE

    Igual Bueno, Mario; Bielsa Azcona, José Enrique

    2011-01-01

    Nowadays efficiency measures are more and more important because the price of the energy is increasing every year. Moreover, saving energy it is also important for decrease the environmental impact. Kastvallen is a hockey arena built in 1997 that cools the hockey rink with electric compressors. The changing rooms are heating by using district heating. Actually the total invoice of electricity is above the 800000 SEK. Meanwhile the district heating invoice reaches the 60000SE...

  15. Economic evaluation of energy saving measures in a common type of Greek building

    International Nuclear Information System (INIS)

    Nikolaidis, Yiannis; Pilavachi, Petros A.; Chletsis, Alexandros

    2009-01-01

    This paper deals with the economic analysis and evaluation of various energy saving measures in the building sector, focusing on a domestic detached house in Greece, i.e. in a typical Mediterranean climate. In order to detect the energy saving measures that, in addition to energy benefits, can also provide economic profits, the study examines the following measures: all kinds of insulation; upgrading of the heating system; use of thermal solar systems; upgrading of lighting; upgrading of electric appliances; upgrading of the cooling system. The economic evaluation methods used for ranking the energy saving measures are the Net Present Value, the Internal Rate of Return, the Savings to Investment Ratio and the Depreciated Payback Period. It has been found that amongst the most effective energy saving methods are the upgrading of lighting, the insulation of the roof of the building and the installation of an automatic temperature control system.

  16. Sosiaalisen median riskit yritysmaailmassa

    OpenAIRE

    Kilpinen, Joni

    2015-01-01

    Sosiaalisen median palveluista on kirjoitettu lukuisia kirjoja ja artikkeleita, joissa niitä ylistetään varsinkin yritysnäkökulmasta. Vaikka sosiaalinen media on muuttanut olennaisesti tapaa, jolla keskustella, mainostaa, etsiä ja jakaa tietoa, piilee sen palveluiden käytössä kuitenkin erilaisia uhkakuvia. Yritykset ja asiantuntijat pelkäävät sosiaalisen median avoimuuden aiheuttavan suuria tietoturvariskejä. Lisäksi asiantuntijat ovat varoitelleet sosiaalisessa mediassa olevista haittaohjelm...

  17. GPU Accelerated Vector Median Filter

    Science.gov (United States)

    Aras, Rifat; Shen, Yuzhong

    2011-01-01

    Noise reduction is an important step for most image processing tasks. For three channel color images, a widely used technique is vector median filter in which color values of pixels are treated as 3-component vectors. Vector median filters are computationally expensive; for a window size of n x n, each of the n(sup 2) vectors has to be compared with other n(sup 2) - 1 vectors in distances. General purpose computation on graphics processing units (GPUs) is the paradigm of utilizing high-performance many-core GPU architectures for computation tasks that are normally handled by CPUs. In this work. NVIDIA's Compute Unified Device Architecture (CUDA) paradigm is used to accelerate vector median filtering. which has to the best of our knowledge never been done before. The performance of GPU accelerated vector median filter is compared to that of the CPU and MPI-based versions for different image and window sizes, Initial findings of the study showed 100x improvement of performance of vector median filter implementation on GPUs over CPU implementations and further speed-up is expected after more extensive optimizations of the GPU algorithm .

  18. Natural gas decompression energy recovery: Energy savings potential in Italy

    International Nuclear Information System (INIS)

    Piatti, A.; Piemonte, C.; Rampini, E.; Vatrano, F.; Techint SpA, Milan; ENEA, Rome

    1992-01-01

    This paper surveyed the natural gas distribution systems employed in the Italian civil, industrial and thermoelectric sectors to identify those installations which can make use of gas decompression energy recovery systems (consisting of turbo-expanders or alternative expanders) to economically generate electric power. Estimates were then made of the total amount of potential energy savings. The study considered as eligible for energy savings interventions only those plants with a greater than 5,000 standard cubic meter per hour plant capacity. It was evaluated that, with suitable decompression equipment installed at 50 key installations (33 civil, 15 industrial), about 200 GWh of power could be produced annually, representing potential savings of about 22,000 petroleum equivalent tonnes of energy. A comparative analysis was done on three investment alternatives involving inputs of varying amounts of Government financial assistance

  19. Energy saving in refineries and petrochemical complexes

    Energy Technology Data Exchange (ETDEWEB)

    Verde, L

    1975-01-01

    Possible measures applicable in the design of refineries and petrochemical complexes, to effect energy savings were investigated. This was not limited to the single process unit problems, on the contrary the attention is mainly addressed to the identification of the interrelations between different units, emphasizing possible integrations. Particularly, the optimization of the pressure levels and number of the utility networks for steam distribution inside plant facilities, is considered, in order to maximize heat recovery in the process units, and electric power production in the central steampower generation plant. A computer program of general application, based on profitability evaluation at various fuel oil prices and different project configurations, has been developed for these purposes. The general measures applicable within certain limits are then briefly examined. The task of the process engineer is discussed in the perspective of the ''energy saving'' goal.

  20. Electric Power Saving Awareness System at School Using ICT

    Directory of Open Access Journals (Sweden)

    Kuzume Koichi

    2016-01-01

    Full Text Available Nowadays, education on energy saving at schools attracts attention to reduce energy consumption. In this paper we proposed a novel system to promote energy conservation activity at schools using a sensor network. The system consisted of a wall-type clock embedded with several kinds of sensors for temperature and light in the classroom, and wireless devices to connect to a cloud computer network. The system had the following superiorities: offered various services for energy conservation activity, needless of CT (Current Transformer sensor, low price, ease of installation and extension, and visualization of power consumption in conjunction with school timetable in real time. We presented the system and a user study conducted to evaluate its usefulness.

  1. A procedure for analysing energy savings in multiple small solar water heaters installed in low-income housing in Brazil

    International Nuclear Information System (INIS)

    Giglio, Thalita; Lamberts, Roberto; Barbosa, Miriam; Urbano, Mariana

    2014-01-01

    Due to government subsidies, Brazil has witnessed an increase in the installation and use of small solar water heating systems in low-income housing projects. Although the initiative has reduced the load curve during peak times due to the reduced use of electric showerheads, measurement and verification (M and V) are needed to validate the savings. M and V procedures should take into account the social and economic variability of low-income housing developments. To improve M and V in low-income housing projects, this paper presents a methodology for identifying homogeneous subgroups based on their energy-saving potential. This research strategy involved a cluster analysis designed to improve the understanding of what energy savers and other influencing factors exist. A case study in Londrina Brazil was undertaken with 200 low-income families. Five clusters, created based on savings potential, were defined. The results showed that only two clusters demonstrated good electricity savings, representing 47% of families. However, two clusters, or 37%, did not provide satisfactory savings, and the other 16% did not provide any consumption history due to previous use of illegal city electricity connection practices. Therefore, studies confirm the need for a detailed measurement of the representative subgroups to assess the influence of human behaviour on potential SWHS-induced savings. - Highlights: • M and V is necessary to improve solar collector-area-based subsidy programmes. • M and V in large-scale sample should contemplate the social and economic variability. • Samples with homogeneous subgroups contribute to a consistent energy-saving M and V. • Solar Water Heaters in some cases may not offer energy saving in a low-income context. • SWH performance decreases with low educational level and difficulty of operation

  2. Progressive electricity tariffs for consumers in Germany?; Progressive Stromtarife fuer Verbraucher in Deutschland?

    Energy Technology Data Exchange (ETDEWEB)

    Tews, Kerstin [Freie Univ. Berlin (Germany). Forschungszentrum fuer Umweltpolitik

    2011-10-15

    More than a quarter of electricity use in Germany is accounted for by private households. This market segment holds vast saving potentials which are not sufficiently made use of to date. If efficiency of electricity use is to serve as a bridge to an era of a nuclear-free power supply, the political realm must find ways of addressing the existing saving potentials more effectively. One possible instrument for creating incentives to save electricity on the demand side is seen in a system of progressive tariffs. How such a system would need to be designed in order to be compatible with the regime of a liberalised electricity market has yet to be investigated however.

  3. How to prevent greenhouse gas emissions in electrical installations: lighting energy savings and solar energy approaches

    Energy Technology Data Exchange (ETDEWEB)

    Yavuz, C.; Aksoy, C. [Sakarya University, Faculty of Engineering, Electrical and Electronics Engineering Department, Serdivan (Turkey)

    2012-07-01

    Day by day greenhouse gas emissions increase dramatically. A passive adaptive method of lighting energy savings, daylight responsive systems are considered one of the best solutions for energy efficiency, saving and prevent CO{sub 2} emissions. Results of an annual experiment which was held in Sakarya University proves the necessity of daylight responsive systems with a 41% energy saving and 942.5 kg of prevented CO{sub 2} emissions Thinking this prevention is realized just only in a 36 m{sup 2} room with the use of 8 luminaries spreading such systems to nationwide, a major amount of greenhouse gas emissions would be prohibited. On the other hand energy saving is not the only way to reduce CO{sub 2} emissions. Again in Sakarya University a project has started to investigate the possibility of illumination of a complete building by using solar energy. This paper evaluates these mentioned systems both in energy efficiency, greenhouse gas emissions prevention and economic point of views. (author)

  4. Route-Based Control of Hybrid Electric Vehicles: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Gonder, J. D.

    2008-01-01

    Today's hybrid electric vehicle controls cannot always provide maximum fuel savings over all drive cycles. Route-based controls could improve HEV fuel efficiency by 2%-4% and help save nearly 6.5 million gallons of fuel annually.

  5. Efficient use of power. Directory for private households to save power without renunciation of comfort; Strom effizient nutzen. Wegweiser fuer Privathaushalte zur wirtschaftlichen Stromeinsparung ohne Komfortverzicht

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    The contribution under consideration is a guide for private households for an economically efficient conservation of electricity without renunciation of comfort. At first, reasons for saving electricity are presented. The approach to reduce power consumption consists of an inventory of electricity consumers, establishment of measures to save electricity as well as a selection of suitable measures. Tables are presented for the determination of the power consumption and costs for electricity in the actual and target state as well as for the determination of the economic efficiency.

  6. Airline enters 2 shared-savings deals for $1M

    Energy Technology Data Exchange (ETDEWEB)

    Barber, J.

    1984-02-06

    Pan American World Airways has two shared-savings agreements to reduce electricity costs at its maintenance base near Miami International Airport by 20 to 25%. The two Andover 256 energy management systems (EMS) to monitor and control lighting and cooling in four buildings are already in operation. A second phase involving solar-powered water heating systems and retrofit work to air conditioning, ventilating, and lighting systems at six other buildings is nearing completion. Pan Am will divide the projected $700,000 in annual energy savings with two investor groups for seven years, after which Pan Am can buy the equipment at fair market value, renew the contract, or have the equipment removed.

  7. Switching non-local median filter

    Science.gov (United States)

    Matsuoka, Jyohei; Koga, Takanori; Suetake, Noriaki; Uchino, Eiji

    2015-06-01

    This paper describes a novel image filtering method for removal of random-valued impulse noise superimposed on grayscale images. Generally, it is well known that switching-type median filters are effective for impulse noise removal. In this paper, we propose a more sophisticated switching-type impulse noise removal method in terms of detail-preserving performance. Specifically, the noise detector of the proposed method finds out noise-corrupted pixels by focusing attention on the difference between the value of a pixel of interest (POI) and the median of its neighboring pixel values, and on the POI's isolation tendency from the surrounding pixels. Furthermore, the removal of the detected noise is performed by the newly proposed median filter based on non-local processing, which has superior detail-preservation capability compared to the conventional median filter. The effectiveness and the validity of the proposed method are verified by some experiments using natural grayscale images.

  8. Functional Median Polish

    KAUST Repository

    Sun, Ying; Genton, Marc G.

    2012-01-01

    polish is demonstrated by comparing its performance with the traditional functional ANOVA fitted by means under different outlier models in simulation studies. The functional median polish is illustrated on various applications in climate science

  9. Five Roots Pattern of Median Nerve Formation

    Directory of Open Access Journals (Sweden)

    Konstantinos Natsis

    2016-04-01

    Full Text Available An unusual combination of median nerve’s variations has been encountered in a male cadaver during routine educational dissection. In particular, the median nerve was formed by five roots; three roots originated from the lateral cord of the brachial plexus joined individually the median nerve’s medial root. The latter (fourth root was united with the lateral (fifth root of the median nerve forming the median nerve distally in the upper arm and not the axilla as usually. In addition, the median nerve was situated medial to the brachial artery. We review comprehensively the relevant variants, their embryologic development and their potential clinical applications.

  10. Price-structure of electricity and district-heating. A background study for energy conservation programme

    International Nuclear Information System (INIS)

    1994-01-01

    The present report deals with the pricing and price-structure of electricity and district-heating with their effects on energy saving. It constitutes part of the groundwork for the new Government Energy Conservation Programme. The report describes principles for the pricing of electricity and district-heating in Finland, and gives some examples of tariffs in foreign countries, which are interesting from the point of view of energy saving. Different utilities apply quite similar pricing principles but there are big differences in price levels between the utilities. The difference in consumer prices can be almost 100 % in the case of electricity and over 150 % as concerns district-heating. The change in retail prices in the last ten years has not had a big general impact on the consumption of electricity or on energy saving. On the other hand, when the price increases of individual utilities are studied, the impact on energy saving at least in the short term can be seen. It seems that an increase of the fixed charges in relation to energy rates has been as a general trend after 1990. To promote energy saving the changing energy rates should be given special emphasis in determining electricity and district-heating tariffs. The opening of the electricity market means that the electricity suppliers face a new situation also when pricing their products. Customers and their expectations will play an increasingly role. (orig.)

  11. Evaluation of Savings in Energy-Efficient Public Housing in the Pacific Northwest

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, A. [Building America Partnership for Improved Residential Construction (BA-PIRC), Cocoa, FL (United States); Lubliner, M. [Building America Partnership for Improved Residential Construction (BA-PIRC), Cocoa, FL (United States); Howard, L. [Building America Partnership for Improved Residential Construction (BA-PIRC), Cocoa, FL (United States); Kunkle, R. [Building America Partnership for Improved Residential Construction (BA-PIRC), Cocoa, FL (United States)

    2013-10-01

    This report presents the results of an energy performance and cost-effectiveness analysis. The Salishan phase 7 and demonstration homes were compared to Salishan phase 6 homes built to 2006 Washington State Energy Code specifications 2. Predicted annual energy savings (over Salishan phase 6) was 19% for Salishan phase 7, and between 19-24% for the demonstration homes (depending on ventilation strategy). Approximately two-thirds of the savings are attributable to the DHP. Working with the electric utility provider, Tacoma Public Utilities, researchers conducted a billing analysis for Salishan phase 7.

  12. Savings needed to fund health insurance and health care expenses in retirement: findings from a simulation model.

    Science.gov (United States)

    Fronstin, Paul; Salisbury, Dallas; VanDerhei, Jack

    2008-05-01

    MODELING RETIREE HEALTH COSTS: This Issue Brief examines the uncertainty of health care expenses in retirement by using a Monte Carlo simulation model to estimate the amount of savings needed to cover health insurance premiums and out-of-pocket health care expenses. This type of simulation is able to account for the uncertainty related to individual mortality and rates of return, and computes the present value of the savings needed to cover health insurance premiums and out-of-pocket expenses in retirement. These observations were used to determine asset targets for having adequate savings to cover retiree health costs 50, 75, and 90 percent of the time. NOT ENOUGH SAVINGS: Many individuals will need more money than the amounts reported in this Issue Brief because this analysis does not factor in the savings needed to cover long-term care expenses, nor does it take into account the fact that many individuals retire prior to becoming eligible for Medicare. However, some workers will need to save less than what is reported if they keep working in retirement and receive health benefits as active workers. WHO HAS RETIREE HEALTH BENEFITS BEYOND MEDICARE?: About 12 percent of private-sector employers report offering any Medicare supplemental health insurance. This increases to about 40 percent among large employers. Overall, nearly 22 percent of retirees age 65 and older had retiree health benefits in 2005 to supplement Medicare coverage. As recently as 2006, 53 percent of retirees age 65 and older were covered by Medicare Part D, 24 percent had outpatient prescription drug coverage through an employment-based plan. Only 10 percent had no prescription drug coverage. INDIVIDUALLY PURCHASED MEDICARE SUPPLEMENTS, 2008: Among those who purchase Medigap and Medicare Part D prescription drug coverage at age 65 in 2008, men would need between $79,000 and $159,000 with median prescription drug expenses (50th percentile and 90th percentiles, respectively), and between $156

  13. The future of utility customer-funded energy efficiency programs in the USA. Projected spending and savings to 2025

    Energy Technology Data Exchange (ETDEWEB)

    Barbose, G.L.; Goldman, C.A.; Hoffman, I.M.; Billingsley, M. [Ernest Orlando Lawrence Berkeley National Laboratory, One Cyclotron Road, MS 90R4000, Berkeley, CA 94720-8136 (United States)

    2013-08-15

    We develop projections of future spending on, and savings from, energy efficiency programs funded by electric and gas utility customers in the USA, under three scenarios through 2025. Our analysis, which updates a previous LBNL study, relies on detailed bottom-up modeling of current state energy efficiency policies, regulatory decisions, and demand-side management and utility resource plans. The three scenarios are intended to represent a range of potential outcomes under the current policy environment (i.e., without considering possible major new policy developments). Key findings from the analysis are as follows: (1) By 2025, spending on electric and gas efficiency programs (excluding load management programs) is projected to double from 2010 levels to USD 9.5 billion in the medium case, compared to USD 15.6 billion in the high case and USD 6.5 billion in the low case; (2) Compliance with statewide legislative or regulatory savings or spending targets is the primary driver for the increase in electric program spending through 2025, though a significant share of the increase is also driven by utility DSM planning activity and integrated resource planning; (3) Our analysis suggests that electric efficiency program spending may approach a more even geographic distribution over time in terms of absolute dollars spent, with the Northeastern and Western states declining from over 70 % of total USA spending in 2010 to slightly more than 50 % in 2025, and the South and Midwest splitting the remainder roughly evenly; (4) Under our medium case scenario, annual incremental savings from customer-funded electric energy efficiency programs increase from 18.4 TWh in 2010 in the USA (which is about 0.5 % of electric utility retail sales) to 28.8 TWh in 2025 (0.8 % of retail sales); (5) These savings would offset the majority of load growth in the Energy Information Administration's most recent reference case forecast, given specific assumptions about the extent to which future

  14. Private Sector Savings

    Directory of Open Access Journals (Sweden)

    Pitonáková Renáta

    2018-03-01

    Full Text Available The majority of household savings are in the form of bank deposits. It is therefore of interest for credit institutions to tailor their deposit policy for getting finances from non-banking entities and to provide the private sector with the loans that are necessary for investment activities and consumption. This paper deals with the determinants of the saving rate of the private sector of Slovakia. Economic, financial and demographic variables influence savings. Growth of income per capita, private disposable income, elderly dependency ratio, real interest rate and inflation have a positive impact on savings, while increases in public savings indicate a crowding out effect. The inflation rate implies precautionary savings, and dependency ratio savings for bequest. There are also implications for governing institutions deciding on the implementation of appropriate fiscal and monetary operations.

  15. Does Daylight Saving Save Energy? A Meta-Analysis

    OpenAIRE

    Havránek, Tomáš; Herman, Dominik; Irsova, Zuzana

    2016-01-01

    The original rationale for adopting daylight saving time (DST) was energy savings. Modern research studies, however, question the magnitude and even direction of the effect of DST on energy consumption. Representing the first meta-analysis in this literature, we collect 162 estimates from 44 studies and find that the mean reported estimate indicates modest energy savings: 0.34% during the days when DST applies. The literature is not affected by publication bias, but the results vary systemati...

  16. On the business value of ICT-controlled plug-in electric vehicle charging in California

    International Nuclear Information System (INIS)

    Goebel, Christoph

    2013-01-01

    The increasing penetration of variable renewable energy, such as wind and solar, requires the deployment of large scale energy storage or dynamic demand side management. Leveraging the intrinsic energy storage potential of certain electric loads could be the key for an efficient transition to green power generation. Plug-in electric vehicles (PEVs) are about to be introduced on a large scale. In this paper, we investigate the savings potential of electricity retailers resulting from the ability to control the charging behavior of a fleet of PEVs using Information and Communication Technology (ICT). This savings potential is important as it could jumpstart the development of advanced control infrastructures for dynamic demand side management. The paper makes three major contributions: first, it applies a novel car usage model based on data from the National Household Travel Survey (NHTS). Second, it develops and evaluates several charging scheduling algorithms with low computational requirements. Third, it identifies several key parameters influencing the relative and absolute savings potential of ICT-controlled PEV charging. We obtain a relative savings potential of up to 45%. The absolute yearly savings per PEV, however, are rather small, which could limit the economic incentives of electricity retailers to deploy the required infrastructure. - Highlights: ► The paper presents a novel model for car usage based on NHTS. ► Several charging scheduling algorithms with low computational requirements are developed and evaluated. ► Several key parameters influencing the relative and absolute savings potential of ICT-controlled PEV charging are identified. ► PEVs can be used to reduce electricity sourcing cost by up to 45%. ► The absolute yearly savings per controlled PEV are rather small and could limit the economic incentives of electricity retailers to deploy the required infrastructure.

  17. Electricity/electronics in electric-powered vehicles and electric management III; Elektrik/Elektronik in Hybrid- und Elektrofahrzeugen und elektrisches Energiemanagement III

    Energy Technology Data Exchange (ETDEWEB)

    Hoff, Carsten; Sirch, Ottmar

    2012-07-01

    The concept of e-Mobility currently is on everyone's lips. Worldwide, manufacturers and suppliers work with high pressure on new concepts and vehicles. Hybrid vehicles pave the way for pure electric-powered vehicles. Due to the problems of energy saving, electric-powered vehicles will take a long time for an extensively utilization. In the book underconsideration, experts from research and practice report on the latest technologies.

  18. Continuous Steering Stability Control Based on an Energy-Saving Torque Distribution Algorithm for a Four in-Wheel-Motor Independent-Drive Electric Vehicle

    Directory of Open Access Journals (Sweden)

    Li Zhai

    2018-02-01

    Full Text Available In this paper, a continuous steering stability controller based on an energy-saving torque distribution algorithm is proposed for a four in-wheel-motor independent-drive electric vehicle (4MIDEV to improve the energy consumption efficiency while maintaining the stability in steering maneuvers. The controller is designed as a hierarchical structure, including the reference model level, the upper-level controller, and the lower-level controller. The upper-level controller adopts the direct yaw moment control (DYC, which is designed to work continuously during the steering maneuver to better ensure steering stability in extreme situations, rather than working only after the vehicle is judged to be unstable. An adaptive two-hierarchy energy-saving torque distribution algorithm is developed in the lower-level controller with the friction ellipse constraint as a basis for judging whether the algorithm needs to be switched, so as to achieve a more stable and energy-efficient steering operation. The proposed stability controller was validated in a co-simulation of CarSim and Matlab/Simulink. The simulation results under different steering maneuvers indicate that the proposed controller, compared with the conventional servo controller and the ordinary continuous controller, can reduce energy consumption up to 23.68% and improve the vehicle steering stability.

  19. An analysis of Water Supply Heat Pump's Capability of Energy Storage and Energy Saving Using Electricity%水源热泵系统蓄能节能的可行性

    Institute of Scientific and Technical Information of China (English)

    吴薇; 张小松

    2002-01-01

    In this paper, the characteristic of water supply heat pump (WLHP) is introduced. The thermal performanceand effect of energy saving that can be used to heating and cooling at the same time (the distinctive working mode) is em-phasized. A new idea of heat input using wave trough electricity instead of boilers is brought up, the effect and significance ofthis new method is discussed.

  20. The estimated impact of California’s urban water conservation mandate on electricity consumption and greenhouse gas emissions

    Science.gov (United States)

    Spang, Edward S.; Holguin, Andrew J.; Loge, Frank J.

    2018-01-01

    In April 2015, the Governor of California mandated a 25% statewide reduction in water consumption (relative to 2013 levels) by urban water suppliers. The more than 400 public water agencies affected by the regulation were also required to report monthly progress towards the conservation goal to the State Water Resources Control Board. This paper uses the reported data to assess how the water utilities have responded to this mandate and to estimate the electricity savings and greenhouse gas (GHG) emissions reductions associated with reduced operation of urban water infrastructure systems. The results show that California succeeded in saving 524 000 million gallons (MG) of water (a 24.5% decrease relative to the 2013 baseline) over the mandate period, which translates into 1830 GWh total electricity savings, and a GHG emissions reduction of 521 000 metric tonnes of carbon dioxide equivalents (MT CO2e). For comparison, the total electricity savings linked to water conservation are approximately 11% greater than the savings achieved by the investor-owned electricity utilities’ efficiency programs for roughly the same time period, and the GHG savings represent the equivalent of taking about 111 000 cars off the road for a year. These indirect, large-scale electricity and GHG savings were achieved at costs that were competitive with existing programs that target electricity and GHG savings directly and independently. Finally, given the breadth of the results produced, we built a companion website, called ‘H2Open’ (https://cwee.shinyapps.io/greengov/), to this research effort that allows users to view and explore the data and results across scales, from individual water utilities to the statewide summary.

  1. Economic and Environmental Impact of Energy Saving in Healthcare Buildings

    Directory of Open Access Journals (Sweden)

    Justo García-Sanz-Calcedo

    2018-03-01

    Full Text Available The purpose of this article is to estimate the economic and environmental impacts of energy consumption derived from healthcare buildings and proposes several energy-saving options in the sector. An experimental energy consumption study was development between 2005 and 2013 in 12 hospitals and 70 healthcare centres in Spain, built between 1980 and 2005 through audits carried out between 2005 and 2012, performed by the Extremadura Energy Agency. The study focused on electric energy, HVAC, DWH, lighting systems, renewable energies, maintenance strategy, thermal insulation, and optimal building size. Specifically, the following parameters were evaluated: energy savings, investment emission of CO2, NO2, and SO2 gases, and payback. The results revealed that through an appropriate energy management of healthcare buildings it is possible to save up to 8.60 kWh/m2 per year, for buildings of less than 5000 m2 (with no beds, which represents an expense of 1.55 €/m2. In healthcare buildings larger than 5000 m2 (with beds, it was possible to save up to 6.88 kWh/m2 per year, which represents an expense of 1.25 €/m2.

  2. Effect of daylight saving time on lighting energy use: A literature review

    International Nuclear Information System (INIS)

    Aries, Myriam B.C.; Newsham, Guy R.

    2008-01-01

    The principal reason for introducing (and extending) daylight saving time (DST) was, and still is, projected energy savings, particularly for electric lighting. This paper presents a literature review concerning the effects of DST on energy use. Simple estimates suggest a reduction in national electricity use of around 0.5%, as a result of residential lighting reduction. Several studies have demonstrated effects of this size based on more complex simulations or on measured data. However, there are just as many studies that suggest no effect, and some studies suggest overall energy penalties, particularly if gasoline consumption is accounted for. There is general consensus that DST does contribute to an evening reduction in peak demand for electricity, though this may be offset by an increase in the morning. Nevertheless, the basic patterns of energy use, and the energy efficiency of buildings and equipment have changed since many of these studies were conducted. Therefore, we recommend that future energy policy decisions regarding changes to DST be preceded by high-quality research based on detailed analysis of prevailing energy use, and behaviours and systems that affect energy use. This would be timely, given the extension to DST underway in North America in 2007

  3. Cost savings from extended life nuclear plants

    International Nuclear Information System (INIS)

    Forest, L.R. Jr.; Deutsch, T.R.; Schenler, W.W.

    1988-09-01

    This study assesses the costs and benefits of nuclear power plant life extension (NUPLEX) for the overall US under widely varying economic assumptions and compares these with alternative new coal- fired plants (NEWCOAL). It is found that NUPLEX saves future electricity consumers more than 3 cents/-kwh compared with NEWCOAL. The NUPLEX costs and benefits for existing individual US nuclear power plants under base-line, or most likely, assumptions are assessed to determine the effects of the basic plant design and plant age. While benefits vary widely, virtually all units would have a positive benefit from NUPLEX. The study also presents a cost-benefit analysis of the nuclear industry's planned advanced light water reactor (ALWR). It is concluded that ALWR offers electrical power at a substantially lower cost than NEWCOAL. 9 refs., 6 figs

  4. Energy saving projects in two steel companies in Fushun City, China

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, investigations and discussions were given on two steel making companies in China. Discussions were given for Fushun Special Steel Co., Ltd. on abolishment and unification of four electric furnaces into two new electric furnaces, and for Fushun New Steel Co., Ltd. on installation of a granulation reinforcing facility, a segregation reinforcing device, and cooler waste heat recovery boilers for the sintering machine, installation of sensors including the waste gas oxygen concentration meter, adoption of a process computer, and optimization of the furnace temperature patterns for the heating furnace. As a result of the discussions, it was revealed that the unit requirement for electric power used at Fushun Special Steel can be reduced largely, and so can the fuel used at Fushun New Steel. The annual energy saving effect would be about 500 million yen relative to the investment amount of 2.8 billion yen at Fushun Special Steel, and about 400 million yen relative to the investment amount of about 400 million yen at Fushun New Steel. The greenhouse gas emission would be reduced annually by 40,000 t-CO2 and 60,000 t-CO2 respectively. Fushun Special Steel will execute an international bid in May this year. (NEDO)

  5. A road to more and cheaper energy conservation. Evaluation of all the Danish energy saving activities; En vej til flere og billigere energibesparelser. Evaluering af samtlige danske energispareaktiviteter

    Energy Technology Data Exchange (ETDEWEB)

    Togeby, M.; Dyhr-Mikkelsen, K.; Damgaard, C.K. (and others)

    2008-12-15

    In total, about 650 million DKK yearly is used in Denmark for energy conservation incentives - 300 million DKK for the electric utilities' energy saving activities, 250 million DKK for energy labelling of buildings, and 100 million DKK for electric power saving activities. The present evaluation of all the Danish energy conservation activities has been performed based on the energy political agreements of 10 June 2005 and of 21 February 2008. The objective is to strengthen and develop the Danish energy savings efforts based on the experiences with the present activities and incentives. The evaluation is performed through data compilations from interviews with selected target groups and from questionnaires to the electric utilities. Furthermore, a statistical analysis was performed of the development of the energy consumption in eight countries, and information of other countries' energy conservation activities was compiled. The energy saving activities and incentives that are evaluated are: Taxes and CO{sub 2} quotas, the electric utilities' activities, energy labelling of buildings, the Electric Power Saving Trust, building codes, labelling of appliances, energy conservation requirements for public workplaces, agreement with the energy intensive industry, and the Energy Conservation Fund. The evaluation of these nine energy saving activities and incentives shows, that they were established over several years as answers to different energy political requirements. The coordination of these activities is in some cases insufficient. At the same time, the implementation of EU's CO{sub 2} quota system is a challenge to the other incentives. For example, the quota system has increased the incentive for electric power savings because of a higher power price but on the other hand it does not result in CO{sub 2} reductions within the actual quota period. Several of the savings systems seem to have too little focus on a systematic documentation of their

  6. Design of electric vehicle charging station based on wind and solar complementary power supply

    Science.gov (United States)

    Wang, Li

    2018-05-01

    Electric vehicles have become a major trend in the development of the automobile industry. Green energy saving is an important feature of their development. At the same time, the related charging facilities construction is also critical. If we improve the charging measures to adapt to its green energy-saving features, it will be to a greater extent to promote its further development. This article will propose a highly efficient green energy-saving charging station designed for the electric vehicles.

  7. The Future of Utility Customer-Funded Energy Efficiency Programs in the United States: Projected Spending and Savings to 2025

    Energy Technology Data Exchange (ETDEWEB)

    Barbose, Galen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Goldman, Charles [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Hoffman, Ian [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Billingsley, Megan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-09-11

    We develop projections of future spending on, and savings from, energy efficiency programs funded by electric and gas utility customers in the United States, under three scenarios through 2025. Our analysis, which updates a previous LBNL study, relies on detailed bottom-up modeling of current state energy efficiency policies, regulatory decisions, and demand-side management and utility resource plans. The three scenarios are intended to represent a range of potential outcomes under the current policy environment (i.e., without considering possible major new policy developments). By 2025, spending on electric and gas efficiency programs (excluding load management programs) is projected to double from 2010 levels to $9.5 billion in the medium case, compared to $15.6 billion in the high case and $6.5 billion in the low case. Compliance with statewide legislative or regulatory savings or spending targets is the primary driver for the increase in electric program spending through 2025, though a significant share of the increase is also driven by utility DSM planning activity and integrated resource planning. Our analysis suggests that electric efficiency program spending may approach a more even geographic distribution over time in terms of absolute dollars spent, with the Northeastern and Western states declining from over 70% of total U.S. spending in 2010 to slightly more than 50% in 2025, with the South and Midwest splitting the remainder roughly evenly. Under our medium case scenario, annual incremental savings from customer-funded electric energy efficiency programs increase from 18.4 TWh in 2010 in the U.S. (which is about 0.5% of electric utility retail sales) to 28.8 TWh in 2025 (0.8% of retail sales). These savings would offset the majority of load growth in the Energy Information Administration’s most recent reference case forecast, given specific assumptions about the extent to which future energy efficiency program savings are captured in that forecast

  8. How to Estimate Demand Charge Savings from PV on Commercial Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Gagnon, Pieter J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bird, Lori A [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-09-28

    Rooftop photovoltaic (PV) systems are compensated through retail electricity tariffs - and for commercial and industrial customers, these are typically comprised of three components: a fixed monthly charge, energy charges, and demand charges. Of these, PV's ability to reduce demand charges has traditionally been the most difficult to estimate. In this fact sheet we explain the basics of demand charges, and provide a new method that a potential customer or PV developer can use to estimate a range of potential demand charge savings for a proposed PV system. These savings can then be added to other project cash flows, in assessing the project's financial performance.

  9. Permasalahan P-Hub Median Dengan Lintasan Terpendek

    OpenAIRE

    Pasaribu, Raja David

    2013-01-01

    Hub are facilities that serve as sorting, switching, and transhipment in a transportation network. P-hub median problem is a discrete case location allocation problem which all hub is fully connected. In this paper will be intoduced Mixed Integrer Linear Programming (MILP) formulation models of cost for p-hub median problem allocation for uncapacitaced single allocation p-hub median(USApHMP). In this paper also introduced Floyd-Warshall shortest path algorithm to solve p-hub median problems a...

  10. Miscellaneous electricity use in U.S. homes

    International Nuclear Information System (INIS)

    Sanchez, Marla C.; Koomey, Jonathan G.; Moezzi, Mithra M.; Meier, Alan; Huber, Wolfgang

    1999-01-01

    Historically, residential energy and carbon saving efforts have targeted conventional end uses such as water heating, lighting and refrigeration. The emergence of new household appliances has transformed energy use from a few large and easily identifiable end uses into a broad array of ''miscellaneous'' energy services. This group of so called miscellaneous appliances has been a major contributor to growth in electricity demand in the past two decades. We use industry shipment data, lifetimes, and wattage and usage estimates of over 90 individual products to construct a bottom-up end use model (1976-2010). The model is then used to analyze historical and forecasted growth trends, and to identify the largest individual products within the miscellaneous end use. We also use the end use model to identify and analyze policy priorities. Our forecast projects that over the period 1996 to 2010, miscellaneous consumption will increase 115 TWh, accounting for over 90 percent of future residential electricity growth. A large portion of this growth will be due to halogen torchiere lamps and consumer electronics, making these two components of miscellaneous electricity a particularly fertile area for efficiency programs. Approximately 20 percent (40 TWh) of residential miscellaneous electricity is ''leaking electricity'' or energy consumed by appliances when they are not performing their principal function. If the standby power of all appliances with a standby mode is reduced to one watt, the potential energy savings equal 21 TWh/yr, saving roughly$1-2 billion annually

  11. Analysis of impact of daylight time savings on energy use of buildings in Kuwait

    Energy Technology Data Exchange (ETDEWEB)

    Krarti, Moncef, E-mail: moncef.krarti@colorado.ed [CEAE Department, CB 428, University of Colorado, Boulder, CO 80309 (United States); Hajiah, Ali [Kuwait Institute for Scientific Research, Safat (Kuwait)

    2011-05-15

    In this paper, a detailed simulation-based analysis is conducted to assess the impact of adopting Daylight Saving Time (DST) on the electrical energy use and peak demand in Kuwait. The analysis focused on the impact of DST in the building sector since it represents 90% of electrical energy usage of Kuwait. The simulation results indicate that the adoption of DST has mixed impacts for Kuwait. While the commercial and the governmental sectors may benefit from the DST, the private residences and apartment buildings can see both their annual energy use and peak demand increase slightly by adopting DST. The overall impact of the DST implementation is rather minimal with a slight increase energy use of about 0.07% and a slight reduction in peak demand of 0.14% or about 12 MW based on 2005 electrical peak demand for Kuwait. - Research highlights: {yields} A detailed simulation-based analysis is conducted to assess the impact of adopting Daylight Saving Time (DST) on the electrical energy use and peak demand in Kuwait. {yields} The analysis focused on the impact of DST in the building sector since it represents 90% of electrical energy usage of Kuwait. {yields} It is found that while the commercial and the governmental building sectors may benefit from DST, the private residences and apartment buildings can see both their annual energy use and peak demand increase slightly by adopting DST. {yields} Since the residential sector represents the majority of the electrical load in Kuwait, DST adoption was found to cause slight increase in annual electrical energy use by about 0.07% and a slight reduction in electrical peak electrical demand by about 0.14%.

  12. Analysis of impact of daylight time savings on energy use of buildings in Kuwait

    International Nuclear Information System (INIS)

    Krarti, Moncef; Hajiah, Ali

    2011-01-01

    In this paper, a detailed simulation-based analysis is conducted to assess the impact of adopting Daylight Saving Time (DST) on the electrical energy use and peak demand in Kuwait. The analysis focused on the impact of DST in the building sector since it represents 90% of electrical energy usage of Kuwait. The simulation results indicate that the adoption of DST has mixed impacts for Kuwait. While the commercial and the governmental sectors may benefit from the DST, the private residences and apartment buildings can see both their annual energy use and peak demand increase slightly by adopting DST. The overall impact of the DST implementation is rather minimal with a slight increase energy use of about 0.07% and a slight reduction in peak demand of 0.14% or about 12 MW based on 2005 electrical peak demand for Kuwait. - Research highlights: → A detailed simulation-based analysis is conducted to assess the impact of adopting Daylight Saving Time (DST) on the electrical energy use and peak demand in Kuwait. → The analysis focused on the impact of DST in the building sector since it represents 90% of electrical energy usage of Kuwait. → It is found that while the commercial and the governmental building sectors may benefit from DST, the private residences and apartment buildings can see both their annual energy use and peak demand increase slightly by adopting DST. → Since the residential sector represents the majority of the electrical load in Kuwait, DST adoption was found to cause slight increase in annual electrical energy use by about 0.07% and a slight reduction in electrical peak electrical demand by about 0.14%.

  13. ANALYSIS OF ENERGY SAVING AND ENERGY EFFICIENCY ISSUES DURING OPERATION OF THE METRO ROLLING STOCK

    Directory of Open Access Journals (Sweden)

    A. V. Donchenko

    2016-06-01

    Full Text Available Purpose.Nowadays a problem of significant power consumption of the rolling stock during its operation is a current issue. In connection with staged electricity rates increase further development of the rail electric transport, including metro rolling stock is impossible without a use of modern energy saving solutions and energy-efficient systems. To solve the specified problem it is necessary to carry out analysis of measures and determine prospective directions in energy saving and increase of energy efficiency on the metro rolling stock. Methodology. Using methods of scientific analysis, generalization, comparative analysis, forecasting and using results of experimental studies, the authors determined main ways for reduction of energy consumption during operation of the metro rolling stock. Energy cost analysis for metro rolling stock of the public utility (PU «Kiev Metro» was carried out. A great number of research works of native and foreign authors concerning the above mentioned problem were analyzed. Findings. Principal directions in energy saving and increase of energy efficiency of the metro rolling stock are implementation of recuperation systems, energy storage systems and energy-efficient control systems. It was determined that implementation of recuperation and energy storage systems helps to save a considerable amount of energy, consumed for traction, but it involves substantial investments. It is pointed out that in current complicated conditions of economic development of Ukraine, use of energy-efficient control systems is a perspective direction in energy saving. Main advantage of this direction is the economic effect obtaining without significant investments. Originality. For the first time was performed potential assessment for energy saving as a result of energy-efficient control systems use at type routine rolling stock operation modes on sections «Khreschatik –Teatralnaya – Khreschatik» and «Shulyavskaya

  14. Intelligent control of energy-saving power generation system

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Zhiyuan; Zhang, Guoqing; Guo, Zhizhong [Harbin Institute of Technology, Harbin (China). Dept. of Electrical Engineering

    2013-07-01

    Highway power generation system which is environmentally friendly and sustainable provides an innovative method of energy conversion. It is also as a kind of city science and technology innovation, which has the characteristics of environmental protection and sustainable utilization. Making full use of vehicle impact speed control humps, we design a new kind of highway speed control humps combined with solar electric generation system integration. Developing green energy, energy saving and environment protection can be achieved.

  15. Industrial plant electrical systems: Simplicity, reliability, cost savings, redundancies

    International Nuclear Information System (INIS)

    Silvestri, A.; Tommazzolli, F.; Pavia Univ.

    1992-01-01

    This article represents a compact but complete design and construction manual for industrial plant electrical systems. It is to be used by design engineers having prior knowledge of local power supply routes and voltages and regards principally the optimum choice of internal distribution systems which can be radial or single, double ringed or with various network configurations, and with single or multiple supplies, and many or few redundancies. After giving guidelines on the choosing of these options, the manual deals with problematics relevant to suitable cable sizing. A cost benefit benefit analysis method is suggested for the choice of the number of redundancies. Recommendations are given for the choice of transformers, motorized equipment, switch boards and circuit breakers. Reference is made to Italian electrical safety and building codes

  16. Retail competition in electricity supply—Survey results in North Carolina

    International Nuclear Information System (INIS)

    McDaniel, Tanga M.; Groothuis, Peter A.

    2012-01-01

    Residential retail competition in electricity supply was introduced in many countries and some US states as part of electricity industry deregulation. Following problems in the electricity market in California in 2000/2001 many US states, including North Carolina, suspended their deregulation agenda. Recent technological advances have made competition more viable, so we ask if NC should reconsider deregulation and retail competition. The welfare benefits will depend on consumers’ willingness to switch suppliers and the potential for value added innovations. In electricity and industries such as pay-tv and telecommunications consumers are ‘sticky’, remaining with their current supplier even though rivals offer savings. Moreover, some analysts question the likelihood of significant welfare improvements from retail competition. We survey residents in two NC counties focusing on: (i) households’ knowledge of and interest in retail competition, (ii) factors that would encourage them to switch suppliers and (iii) the required savings to encourage switching. About 50–65% of respondents would favor retail competition in NC. Demographic variables and experience switching in other industries affect opinions and the savings required to incent switching. We conclude the estimated rate reduction to encourage competitive switching will be hard to achieve in NC as long as rates remain below the national average. - Highlights: ► NC survey results suggest residents are interested in utility supply competition. ► Socio-demographic variables affect opinions. ► A lower bound on required savings to incent switching is about 1.4¢/kWh. ► NC residential rates are below the national average, so such a savings is unlikely.

  17. Preliminary study of potential energy savings within business and industry by reducing over-harmonies; Forundersoegelse af muligheder for energibesparelser i erhvervslivet ved reduktion af overharmoniske stroemme

    Energy Technology Data Exchange (ETDEWEB)

    Johansson, M. (Dansk Energi Analyse A/S, Frederiksberg (Denmark)); Kehr, J.M. (ABB A/S, Skovlunde (Denmark)); Hoejte Hansen, H. (Balslev A/S (Denmark))

    2009-08-15

    Overharmonic currents cause additional losses in the power supply network (lines, transformers) and in motors, which are supplied directly from the network (not motors, which are supplied from frequency converters or rectifiers). The overharmonic currents can be reduced or removed by capacitor banks and active filters. Active filters adjust themselves to the loading conditions and are also reacting on too slow transients and voltage disturbances in the network. Till now there is only little experience with active filters in commercial life. However, there are indications of potential electricity savings up to 10 % in installations with many overharmonic voltages (THDU > 5 %). The extent of harmonic distortions has been measured in 10 firms and has been compared to previous measurements. It is estimated that the voltage distortion, measured in THDU, at least must be 5 or 6 % in order to establish a profitable solution by reducing the harmonics by means of an active filter. In approx 40 % of the cases where the THDU has been measured, it has been estimated on the basis of THDU, current and utilization time that there is a potential of electricity savings by reducing the THDU. The overharmonic currents cause additional current heating losses in directly supplied motors as well as in lines and transformers. In induction motors they also cause current heating losses in the rotor and the 5th, 11th, 17th etc harmonics make a pulsating or reduced torque, which implies further losses. ABB and Comsys, both of which deliver active filters, have calculated electricity savings in some installations equipped with active filters. The direct electricity savings have been estimated at a low per cent in production equipment generally and up to 16 % in some directly supplied induction motors. In addition to the direct electricity savings the filters may also result in increased production capacity as a consequence of fewer breakdowns (the filters improve the voltage quality and

  18. The Ultrasonographic Findings of Bifid Median Nerve

    International Nuclear Information System (INIS)

    Park, Hee Jin; Park, Noh Hyuck; Joh, Joon Hee; Lee, Sung Moon

    2009-01-01

    We wanted to evaluate the ultrasonographic findings of bifid median nerve and its clinical significance. We retrospectively reviewed five cases (three men and two women, mean age: 54 years) of incidentally found bifid median nerve from 264 cases of clinically suspected carpal-tunnel syndrome that were seen at our hospital during last 6 years. Doppler sonography was performed in all five cases and MR angiography was done in one case for detecting a persistent median artery. The difference (ΔCSA) between the sum of the cross-sectional areas of the bifid median nerve at the pisiform level (CSA2) and the cross-sectional area proximal to the bifurcation(CSA1) was calculated. The incidence of a bifid median nerve was 1.9%. All the patients presented with a tingling sensation on a hand and two patients had nocturnal pain. All the cases showed bifurcation of the nerve bundle proximal to the carpal tunnel. The margins appeared relatively smooth and each bundle showed a characteristic fascicular pattern. A persistent median artery was noted between the bundles in four cases. ΔCSA was more than 2 mm 2 in four cases. Bifid median nerve with a persistent median artery is a relatively rare normal variance and these are very important findings before performing surgical intervention to avoid potential nerve injury and massive bleeding. We highly suggest that radiologists should understand the anatomical characteristics of this anomaly and make efforts to detect it

  19. Integrating wind power using intelligent electric water heating

    International Nuclear Information System (INIS)

    Fitzgerald, Niall; Foley, Aoife M.; McKeogh, Eamon

    2012-01-01

    Dwindling fossil fuel resources and pressures to reduce greenhouse gas emissions will result in a more diverse range of generation portfolios for future electricity systems. Irrespective of the portfolio mix the overarching requirement for all electricity suppliers and system operators is to instantaneously meet demand, to operate to standards and reduce greenhouse gas emissions. Therefore all electricity market participants will ultimately need to use a variety of tools to balance the power system. Thus the role of demand side management with energy storage will be paramount to integrate future diverse generation portfolios. Electric water heating has been studied previously, particularly at the domestic level to provide load control, peak shave and to benefit end-users financially with lower bills, particularly in vertically integrated monopolies. In this paper a number of continuous direct load control demand response based electric water heating algorithms are modelled to test the effectiveness of wholesale electricity market signals to study the system benefits. The results are compared and contrasted to determine which control algorithm showed the best potential for energy savings, system marginal price savings and wind integration.

  20. Saving can save from death anxiety: mortality salience and financial decision-making.

    Science.gov (United States)

    Zaleskiewicz, Tomasz; Gasiorowska, Agata; Kesebir, Pelin

    2013-01-01

    Four studies tested the idea that saving money can buffer death anxiety and constitute a more effective buffer than spending money. Saving can relieve future-related anxiety and provide people with a sense of control over their fate, thereby rendering death thoughts less threatening. Study 1 found that participants primed with both saving and spending reported lower death fear than controls. Saving primes, however, were associated with significantly lower death fear than spending primes. Study 2 demonstrated that mortality primes increase the attractiveness of more frugal behaviors in save-or-spend dilemmas. Studies 3 and 4 found, in two different cultures (Polish and American), that the activation of death thoughts prompts people to allocate money to saving as opposed to spending. Overall, these studies provided evidence that saving protects from existential anxiety, and probably more so than spending.

  1. Saving can save from death anxiety: mortality salience and financial decision-making.

    Directory of Open Access Journals (Sweden)

    Tomasz Zaleskiewicz

    Full Text Available Four studies tested the idea that saving money can buffer death anxiety and constitute a more effective buffer than spending money. Saving can relieve future-related anxiety and provide people with a sense of control over their fate, thereby rendering death thoughts less threatening. Study 1 found that participants primed with both saving and spending reported lower death fear than controls. Saving primes, however, were associated with significantly lower death fear than spending primes. Study 2 demonstrated that mortality primes increase the attractiveness of more frugal behaviors in save-or-spend dilemmas. Studies 3 and 4 found, in two different cultures (Polish and American, that the activation of death thoughts prompts people to allocate money to saving as opposed to spending. Overall, these studies provided evidence that saving protects from existential anxiety, and probably more so than spending.

  2. Electric energy saving in the cellulose and paper industry; Ahorro de energia electrica en la industria de celulosa y papel

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    This paper delineates the results of the demonstration project for electric energy saving, which is one of the twenty four projects in which the Fideicomiso de Apoyo al Programa de Ahorro de Energia (FIDE) sponsors the diagnosis as well as the applied measures and the measures currently in application. Also the potential opportunity areas and the measures applied and in course of application, as well as the required investments and their recuperation periods. [Espanol] En este trabajo se describen los resultados del proyecto de demostracion de ahorro de energia electrica que es uno de los veinticuatro proyectos, en los que el Fideicomiso de Apoyo al Programa de Ahorro de Energia (FIDE) financia tanto el diagnostico como la aplicacion de medidas. Se presentan tanto las areas de oportunidad, potenciales y medidas aplicadas y en aplicacion, asi como las inversiones requeridas y los periodos de recuperacion de las mismas.

  3. Electric energy saving in the cellulose and paper industry; Ahorro de energia electrica en la industria de celulosa y papel

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-12-31

    This paper delineates the results of the demonstration project for electric energy saving, which is one of the twenty four projects in which the Fideicomiso de Apoyo al Programa de Ahorro de Energia (FIDE) sponsors the diagnosis as well as the applied measures and the measures currently in application. Also the potential opportunity areas and the measures applied and in course of application, as well as the required investments and their recuperation periods. [Espanol] En este trabajo se describen los resultados del proyecto de demostracion de ahorro de energia electrica que es uno de los veinticuatro proyectos, en los que el Fideicomiso de Apoyo al Programa de Ahorro de Energia (FIDE) financia tanto el diagnostico como la aplicacion de medidas. Se presentan tanto las areas de oportunidad, potenciales y medidas aplicadas y en aplicacion, asi como las inversiones requeridas y los periodos de recuperacion de las mismas.

  4. Driving with electrical power

    International Nuclear Information System (INIS)

    Ursin, M.; Hoeckel, M.

    2008-01-01

    This article takes a look at the chances offered to the electricity supply industry by the increasing use of battery-driven vehicles - and the advantages thus offered to the environment. The use of the vehicles' batteries to form a distributed electricity storage scheme is discussed. The authors comment that, although electrically-driven vehicles consume more power, the total primary energy consumption and pollutant emissions will be reduced. The actual electricity consumption of electric vehicles and the source of this power are examined. Power saved by the reduced use of electrical heating systems and boilers could, according to the authors, be used to charge the batteries of electric vehicles. The use of these batteries as a storage system to help regulate electricity supplies is discussed and the steps to be taken for the implementation of such a system are listed

  5. Mechanical design of electric motors

    CERN Document Server

    Tong, Wei

    2014-01-01

    Rapid increases in energy consumption and emphasis on environmental protection have posed challenges for the motor industry, as has the design and manufacture of highly efficient, reliable, cost-effective, energy-saving, quiet, precisely controlled, and long-lasting electric motors.Suitable for motor designers, engineers, and manufacturers, as well as maintenance personnel, undergraduate and graduate students, and academic researchers, Mechanical Design of Electric Motors provides in-depth knowledge of state-of-the-art design methods and developments of electric motors. From motor classificati

  6. Basic survey project for Joint Implementation, etc., fiscal 1999. Survey of modernization of energy saving equipment at Southern Steel

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing greenhouse effect gas emissions, a project was studied for the modernization of energy saving facilities at Southern Steel Co., Ltd. which is No. 2 iron/steel maker in Malaysia. Studies were made on scrap preheating equipment for electric furnace, direct hot charge rolling equipment (DHCR), and regenerative burner for billet heating furnace. The scrap preheating equipment recovers energy from the electric furnace exhaust gas, which saves energy of 70 kWh/t. The direct hot charge rolling equipment recovers the sensible heat of billets, of which energy saving of about 80 Mcal/t is expected. The generative burner, in which the ceramic heat exchanger is used, improves the heat recovery from exhaust gas by 20%. By adopting these technologies, an effect of energy saving of a total of 325 Mcal/t can be obtained. If the four major iron/steel making plants in Malaysia adopt the technologies, effects can be obtained of energy conservation of approximately 100,000 toe/y and reduction in greenhouse effect gas emissions by approximately 320,000 t-CO2/y. (NEDO)

  7. ORC waste heat recovery in European energy intensive industries: Energy and GHG savings

    International Nuclear Information System (INIS)

    Campana, F.; Bianchi, M.; Branchini, L.; De Pascale, A.; Peretto, A.; Baresi, M.; Fermi, A.; Rossetti, N.; Vescovo, R.

    2013-01-01

    Highlights: • A methodology to estimate ORC industrial heat recovery potential is defined. • Heat recovery applications for different industrial processes are shown. • Cement, steel, glass and oil and gas applications are considered in EU27. • Savings in electricity costs and greenhouse gases are quantified. - Abstract: Organic Rankine Cycle (ORC) is a technology with important opportunities in heat recovery from energy intensive industrial processes. This paper represents the first comprehensive estimate of ORC units that can be installed in cement, steel, glass and oil and gas industries in the 27 countries of the European Union based on an accurate methodology related to real plants in operation or under construction. An evaluation of energy savings, depending on the number of operating hours per year and of the consequent decrease in CO 2 emission and electricity expenditure, is also provided. The study, carried out in the framework of an European research project on heat recovery in energy intensive industries, found that, in the most convenient considered scenario, up to about 20,000 GW h of thermal energy per year can be recovered and 7.6 M ton of CO 2 can be saved by the application of ORC technology to the investigated and most promising industrial sectors

  8. Testing the gravity p-median model empirically

    Directory of Open Access Journals (Sweden)

    Kenneth Carling

    2015-12-01

    Full Text Available Regarding the location of a facility, the presumption in the widely used p-median model is that the customer opts for the shortest route to the nearest facility. However, this assumption is problematic on free markets since the customer is presumed to gravitate to a facility by the distance to and the attractiveness of it. The recently introduced gravity p-median model offers an extension to the p-median model that account for this. The model is therefore potentially interesting, although it has not yet been implemented and tested empirically. In this paper, we have implemented the model in an empirical problem of locating vehicle inspections, locksmiths, and retail stores of vehicle spare-parts for the purpose of investigating its superiority to the p-median model. We found, however, the gravity p-median model to be of limited use for the problem of locating facilities as it either gives solutions similar to the p-median model, or it gives unstable solutions due to a non-concave objective function.

  9. Switching non-local vector median filter

    Science.gov (United States)

    Matsuoka, Jyohei; Koga, Takanori; Suetake, Noriaki; Uchino, Eiji

    2016-04-01

    This paper describes a novel image filtering method that removes random-valued impulse noise superimposed on a natural color image. In impulse noise removal, it is essential to employ a switching-type filtering method, as used in the well-known switching median filter, to preserve the detail of an original image with good quality. In color image filtering, it is generally preferable to deal with the red (R), green (G), and blue (B) components of each pixel of a color image as elements of a vectorized signal, as in the well-known vector median filter, rather than as component-wise signals to prevent a color shift after filtering. By taking these fundamentals into consideration, we propose a switching-type vector median filter with non-local processing that mainly consists of a noise detector and a noise removal filter. Concretely, we propose a noise detector that proactively detects noise-corrupted pixels by focusing attention on the isolation tendencies of pixels of interest not in an input image but in difference images between RGB components. Furthermore, as the noise removal filter, we propose an extended version of the non-local median filter, we proposed previously for grayscale image processing, named the non-local vector median filter, which is designed for color image processing. The proposed method realizes a superior balance between the preservation of detail and impulse noise removal by proactive noise detection and non-local switching vector median filtering, respectively. The effectiveness and validity of the proposed method are verified in a series of experiments using natural color images.

  10. Trigeneration primary energy saving evaluation for energy planning and policy development

    International Nuclear Information System (INIS)

    Chicco, Gianfranco; Mancarella, Pierluigi

    2007-01-01

    Trigeneration or combined heat, cooling and power (CHCP) is becoming an increasingly important energy option, particularly on a small-scale basis (below 1 MW e ), with several alternatives nowadays available for the cooling power production and the coupling to cogeneration systems. This paper deals with the introduction of a suitable framework for assessing the energy saving performance of trigeneration alternatives, orientated towards energy planning studies and the development of regulatory policies. In particular, a new generalized performance indicator-the trigeneration primary energy saving (TPES)-is introduced and discussed, with the aim of effectively evaluating the primary energy savings from different CHCP alternatives. The potential of the TPES indicator is illustrated through specific analyses run over different combinations of trigeneration equipment, providing numerical examples based on time-domain simulations to illustrate the dependence of the energy saving characteristics on the CHCP system configurations and equipment, as well as on the loading levels. In addition, the key aspect of adequately establishing the reference efficiencies for the conventional separate production of electrical, thermal and cooling power is addressed in detail. This aspect affects both equipment selection and potential profitability of the considered solutions under the outlook of receiving financial incentives

  11. Savings potential of ENERGY STAR (registered trademark) voluntary labeling programs

    International Nuclear Information System (INIS)

    Webber, Carrie A.; Brown, Richard E.

    1998-01-01

    In 1993 the U.S. Environmental Protection Agency (EPA) introduced ENERGY STAR (registered trademark), a voluntary labeling program designed to identify and promote energy-efficient products. Since then EPA, now in partnership with the U.S. Department of Energy (DOE), has introduced programs for more than twenty products, spanning office equipment, residential heating and cooling equipment, new homes, commercial and residential lighting, home electronics, and major appliances. We present potential energy, dollar and carbon savings forecasts for these programs for the period 1998 to 2010. Our target market penetration case represents our best estimate of future ENERGY STAR savings. It is based on realistic market penetration goals for each of the products. We also provide results under the assumption of 100% market penetration; that is, we assume that all purchasers buy ENERGY STAR-compliant products instead of standard efficiency products throughout the analysis period. Finally, we assess the sensitivity of our target penetration case forecasts to greater or lesser marketing success by EPA and DOE, lower-than-expected future energy prices, and higher or lower rates of carbon emission by electricity generators. The potential savings of ENERGY STAR are substantial. If all purchasers chose Energy Star-compliant products instead of standard efficiency products over the next 15 years, they would save more than$100 billion on their energy bills during those 15 years. (Bill savings are in 1995 dollars, discounted at a 4% real discount rate.)

  12. NREL Evaluates Performance of Fast-Charge Electric Buses

    Energy Technology Data Exchange (ETDEWEB)

    2016-09-16

    This real-world performance evaluation is designed to enhance understanding of the overall usage and effectiveness of electric buses in transit operation and to provide unbiased technical information to other agencies interested in adding such vehicles to their fleets. Initial results indicate that the electric buses under study offer significant fuel and emissions savings. The final results will help Foothill Transit optimize the energy-saving potential of its transit fleet. NREL's performance evaluations help vehicle manufacturers fine-tune their designs and help fleet managers select fuel-efficient, low-emission vehicles that meet their bottom line and operational goals. help Foothill Transit optimize the energy-saving potential of its transit fleet. NREL's performance evaluations help vehicle manufacturers fine-tune their designs and help fleet managers select fuel-efficient, low-emission vehicles that meet their bottom line and operational goals.

  13. Prediction of dynamic Rankine Cycle waste heat recovery performance and fuel saving potential in passenger car applications considering interactions with vehicles’ energy management

    International Nuclear Information System (INIS)

    Horst, Tilmann Abbe; Tegethoff, Wilhelm; Eilts, Peter; Koehler, Juergen

    2014-01-01

    Highlights: • Method for evaluating fuel saving potential of vehicle waste heat recovery systems. • Analysis of interactions between waste heat recovery system and vehicle. • Evaluation of fuel saving potential in dynamic motorway driving scenario. • Parameter study for increasing fuel saving potential of integrated system. - Abstract: Waste heat recovery (WHR) by means of a Rankine Cycle is a promising approach for achieving reductions in fuel consumption and, as a result, exhaust emissions of passenger car engines. To find the best compromise between complexity and fuel saving potential, methods for predicting the WHR performance for different system configurations and stationary as well as dynamic driving scenarios are needed. Since WHR systems are usually not included in today’s car concepts, they are mostly designed as add-on systems. As a result their integration may lead to negative interactions due to increased vehicle weight, engine backpressure and cooling demand. These effects have to be considered when evaluating the fuel saving potential. A new approach for predicting WHR performance and fuel saving potential was developed and is presented in this paper. It is based on simple dynamic models of a system for recovering exhaust gas waste heat and its interfaces with the vehicle: the exhaust system for heat input, the on-board electric system for power delivery and the engine cooling system for heat rejection. The models are validated with test bench measurements of the cycle components. A study of fuel saving potential in an exemplary dynamic motorway driving scenario shows the effect of vehicle integration: while the WHR system could improve fuel economy by 3.4%, restrictions in power output due to the architecture of the on-board electric system, package considerations, increased weight, cooling demand and exhaust gas backpressure lead to a reduction of fuel saving potential by 60% to 1.3%. A parameter study reveals that, in addition to weight

  14. Electric drive choices for light, medium, and heavy duty vehicles to reduce their climate change impact in Canada

    International Nuclear Information System (INIS)

    Fitzpatrick, N.P.

    2009-01-01

    The evolution of electric drive technologies from 1988, at the 9 th International Electric Vehicle Symposium (EVS 9) in Toronto, to 2007 at EVS 23 in Anaheim, is described. Total hybridization of Canada's fleet of light, medium and heavy duty vehicles would result in greenhouse reductions savings of 30 Mt of CO 2 E per year, similar to the saving from a 25% reduction in vehicle weight. Further savings in greenhouse reductions from plug-in hybrids require a battery cost similar to that needed for electric vehicles. Further development of both ultracapacitors and batteries is needed as is work on other parts of the electric drive supply chain. (author)

  15. Potential energy savings in renovation projects of residential and service buildings; Energiansaeaestoemahdollisuudet rakennuskannan korjaustoiminnassa

    Energy Technology Data Exchange (ETDEWEB)

    Heljo, J.; Vihola, J.

    2012-11-01

    The study estimates the feasible energy savings potential in the 2010 building stock by 2050. The focus is on energy-saving measures related to renovation of residential and service buildings. The calculations were done by building types and age groups using the EKOREM calculation model. The calculations indicate the building types and structural elements where potential for savings exists. The study did not consider energy-saving measures related to changes in heating systems, electrical equipment, property maintenance or use habits. The study disproved the common belief that considerably more energy savings could be achieved faster by focussing on the existing building stock instead of new construction. That is mainly due the fact that it generally pays to implement structural energy-saving measures only when the targeted elements also require other significant repairs besides energy-efficiency improvements. Thus, energy renovations cannot be speeded up very much. The clearest exception are the extra insulations added to roof assemblies that are easy to implement. Attempts to save more energy in the building stock than can be achieved at a small additional cost in connection with needed renovations may multiply costs, and the saving in energy costs will not necessarily cover the additional investments. The efficiency of energy-saving measures can be affected by recommending or ordering use of more energy efficient windows, thicker extra insulations or more efficient ventilation heat recovery systems than the standard solution selected in connection with renovations. The goal of preserving the characteristics of buildings of cultural-historical or architectural value and the typical solutions and materials used in all buildings of a certain period limit the repair and renovation of structural elements. In the case of these buildings, improvement of energy efficiency can be considered in connection with the planning of renovations and the buildings' use and

  16. Spending to save

    DEFF Research Database (Denmark)

    Larsen, Anders

    2013-01-01

    the energy distribution companies meet their overall saving obligation, the net savings impact are about a third of the savings reported by the obligated parties. Further it was found that while energy savings in the public and business sector have a high net impact, some subsidies given under the EEO...... perspective. The evaluation has resulted in noticeable adjustments of the design of the Danish EEO, e.g. introduction of a 1 year payback-time limit for projects receiving subsidies, a minimum baseline for insulation products, and specification of documentation requirements....

  17. Monitoring and Characterization of Miscellaneous Electrical Loads in a Large Retail Environment

    Energy Technology Data Exchange (ETDEWEB)

    Gentile-Polese, L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Frank, S. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sheppy, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lobato, C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Rader, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Long, N. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-02-01

    Buildings account for 40% of primary energy consumption in the United States (residential 22%; commercial 18%). Most (70% residential and 79% commercial) is used as electricity. Thus, almost 30% of U.S. primary energy is used to provide electricity to buildings. Plug loads play an increasingly critical role in reducing energy use in new buildings (because of their increased efficiency requirements), and in existing buildings (as a significant energy savings opportunity). If all installed commercial building miscellaneous electrical loads (CMELs) were replaced with energy-efficient equipment, a potential annual energy saving of 175 TWh, or 35% of the 504 TWh annual energy use devoted to MELs, could be achieved. This energy saving is equivalent to the annual energy production of 14 average-sized nuclear power plants. To meet DOE's long-term goals of reducing commercial building energy use and carbon emissions, the energy efficiency community must better understand the components and drivers of CMEL energy use, and develop effective reduction strategies. These goals can be facilitated through improved data collection and monitoring methodologies, and evaluation of CMELs energy-saving techniques.

  18. Exploring the time-saving bias: How drivers misestimate time saved when increasing speed

    Directory of Open Access Journals (Sweden)

    Eyal Peer

    2010-12-01

    Full Text Available According to the time-saving bias, drivers underestimate the time saved when increasing from a low speed and overestimate the time saved when increasing from a relatively high speed. Previous research used a specific type of task --- drivers were asked to estimate time saved when increasing speed and to give a numeric response --- to show this. The present research conducted two studies with multiple questions to show that the time-saving bias occurs in other tasks. Study 1 found that drivers committed the time-saving bias when asked to estimate (a the time saved when increasing speed or (b the distance that can be completed at a given time when increasing speed or (c the speed required to complete a given distance in decreasing times. Study 2 showed no major differences in estimations of time saved compared to estimations of the remaining journey time and also between responses given on a numeric scale versus a visual analog scale. Study 3 tested two possible explanations for the time-saving bias: a Proportion heuristic and a Differences heuristic. Some evidence was found for use of the latter.

  19. Hybrid-electric propulsion for automotive and aviation applications

    OpenAIRE

    Friedrich, C; Robertson, Paul Andrew

    2014-01-01

    In parallel with the automotive industry, hybrid-electric propulsion is becoming a viable alternative propulsion technology for the aviation sector and reveals potential advantages including fuel savings, lower pollution, and reduced noise emission. Hybrid-electric propulsion systems can take advantage of the synergy between two technologies by utilizing both internal combustion engines and electric motors together, each operating at their respective optimum conditions...

  20. Lower electricity prices and greenhouse gas emissions due to rooftop solar: empirical results for Massachusetts

    International Nuclear Information System (INIS)

    Kaufmann, Robert K.; Vaid, Devina

    2016-01-01

    Monthly and hourly correlations among photovoltaic (PV) capacity utilization, electricity prices, electricity consumption, and the thermal efficiency of power plants in Massachusetts reduce electricity prices and carbon emissions beyond average calculations. PV utilization rates are highest when the thermal efficiencies of natural gas fired power plants are lowest, which reduces emissions of CO 2 and CH 4 by 0.3% relative to the annual average emission rate. There is a positive correlation between PV utilization rates and electricity prices, which raises the implied price of PV electricity by up to 10% relative to the annual average price, such that the average MWh reduces electricity prices by $0.26–$1.86 per MWh. These price reductions save Massachusetts rate-payers $184 million between 2010 and 2012. The current and net present values of these savings are greater than the cost of solar renewable energy credits which is the policy instrument that is used to accelerate the installation of PV capacity. Together, these results suggest that rooftop PV is an economically viable source of power in Massachusetts even though it has not reached socket parity. - Highlights: •Implied price of PV up to 10% greater than the annual average price. •PV saves Massachusetts rate-payers $184 million in 2010–2012. •Annual savings are greater than the cost of solar renewable energy credits. •Savings rise longer lifetime of PV systems and pay period for SREC's shortened. •PV reduces emissions of CO 2 and CH 4 by 0.3% relative to the annual average.

  1. U.S. Army Reserve 88th Readiness Division Finds Big Savings

    Energy Technology Data Exchange (ETDEWEB)

    None

    2018-02-20

    Fact sheet features lighting work done for the U.S. Army Reserve 88th Readiness Division, which was recognized in two 2017 Interior Lighting Campaign exemplary recognition categories. The troffer lighting upgrade projects at the two recognized sites are expected to save more than 246,000 kWh annually or roughly enough electricity to run 23 homes for a year.

  2. Median Nerve Conduction in Healthy Nigerians: Normative Data

    African Journals Online (AJOL)

    of median nerve disease using multiple studies, and rendering ... Aim: To develop normative values for motor and sensory median nerve ..... Table 5: Comparison of median motor nerve conduction study parameters to studies elsewhere. Study.

  3. Lowering electricity prices through deregulation

    OpenAIRE

    Thomas Klitgaard; Rekha Reddy

    2000-01-01

    A wave of regulatory reform is now transforming the U.S. electricity industry. As state and federal authorities allow independent power producers to compete with utilities in supplying electricity, consumers are paying close attention to the effects of this change on their energy bills. Although deregulation poses significant structural challenges, the introduction of competitive pressures should ultimately lead to efficiency gains for the industry and cost savings for households and businesses.

  4. Centralized or decentralized electricity production

    International Nuclear Information System (INIS)

    Boer, H.A. de.

    1975-01-01

    Because of low overall efficiency in electric power generation, it is argued that energy provision based on gas, combined with locally decentralized electricity production, saves for the Netherlands slightly more fossile fuel than nuclear technologies and makes the country independent of uranium resources. The reason the Netherlands persues this approach is that a big part of the energy is finally used for heating in the normal or moderate temperatures

  5. Electricity Profile Study for Domestic and Commercial Sectors

    OpenAIRE

    Asmarashid Ponniran; Nur Azura Mamat; Ariffudin Joret

    2012-01-01

    As Malaysia move towards as a developed country, it is expected that the electricity consumption in domestic and commercial sectors will increase as well as more industrials and households need. This study is to investigate the electricity profile in domestic and commercial sectors by monitoring some appropriate appliances that contribute high electricity consumption. The characteristics for every major loads are examined and the potential energy saving is compared to an efficient electrical ...

  6. Economic analysis of Brazilian policies for energy efficient electric motors

    International Nuclear Information System (INIS)

    Andrade, Cássio Tersandro de Castro; Pontes, Ricardo Silva Thé

    2017-01-01

    Brazil is leading several energy efficiency initiatives and has ambitious goals for 2030, according to the Brazilian National Energy Plan 2030. One of the main initiatives is the minimum efficiency performance standards (MEPS) program for energy-driven equipment and the electric motors appear as the most significant one (49% share of the total electricity consumption). The MEPS levels set new grades for efficiency, and then manufacturers and consumers have to conform to the new products and costs. Policy makers have to economically assess the effects of these MEPS in order to maintain the market stability. Since the benefits of this program come from future energy savings, this cost-effective analysis has to consider the parameters uncertainty and the results should reinforce the market players’ confidence. Thus, the goal of this work is, first, to analyze the economic viability of the MEPS transitions in Brazil considering the uncertainty of the parameters involved and then, to estimate the effects of this program on the energy savings goals for 2030. At the end, we also verify whether this investment in energy efficiency is competitive with other forms of investments in energy. - Highlights: • A cost-effectiveness method with uncertainty for efficiency program is presented. • Savings from electric motors MEPS program makes the 2030 Brazilian goals possible. • Electric motors MEPS program cost-effectiveness in Brazil is confirmed. • Saved energy cost from efficiency improvement is a competitive energy investment.

  7. Matrix converter applied to energy saving for street lighting systems

    OpenAIRE

    Román Lumbreras, Manuel; Velasco Quesada, Guillermo; Conesa Roca, Alfons

    2010-01-01

    This work presents a three-phase AC-AC converter, with independent phase control, based on matrix-converter structure. This converter is applied to electrical energy saving on the public lighting systems by means of regulation and control of the voltage applied to the lamps. The developed converter represents a technological improvement with respect to the traditional systems based on an autotransformer: it reduces system cost and volume, and increases lamps lifetime.

  8. Job Exposure Matrix for Electric Shock Risks with Their Uncertainties

    Science.gov (United States)

    Vergara, Ximena P.; Fischer, Heidi J.; Yost, Michael; Silva, Michael; Lombardi, David A.; Kheifets, Leeka

    2015-01-01

    We present an update to an electric shock job exposure matrix (JEM) that assigned ordinal electric shocks exposure for 501 occupational titles based on electric shocks and electrocutions from two available data sources and expert judgment. Using formal expert elicitation and starting with data on electric injury, we arrive at a consensus-based JEM. In our new JEM, we quantify exposures by adding three new dimensions: (1) the elicited median proportion; (2) the elicited 25th percentile; and (3) and the elicited 75th percentile of those experiencing occupational electric shocks in a working lifetime. We construct the relative interquartile range (rIQR) based on uncertainty interval and the median. Finally, we describe overall results, highlight examples demonstrating the impact of cut point selection on exposure assignment, and evaluate potential impacts of such selection on epidemiologic studies of the electric work environment. In conclusion, novel methods allowed for consistent exposure estimates that move from qualitative to quantitative measures in this population-based JEM. Overlapping ranges of median exposure in various categories reflect our limited knowledge about this exposure. PMID:25856552

  9. Job Exposure Matrix for Electric Shock Risks with Their Uncertainties

    Directory of Open Access Journals (Sweden)

    Ximena P. Vergara

    2015-04-01

    Full Text Available We present an update to an electric shock job exposure matrix (JEM that assigned ordinal electric shocks exposure for 501 occupational titles based on electric shocks and electrocutions from two available data sources and expert judgment. Using formal expert elicitation and starting with data on electric injury, we arrive at a consensus-based JEM. In our new JEM, we quantify exposures by adding three new dimensions: (1 the elicited median proportion; (2 the elicited 25th percentile; and (3 and the elicited 75th percentile of those experiencing occupational electric shocks in a working lifetime. We construct the relative interquartile range (rIQR based on uncertainty interval and the median. Finally, we describe overall results, highlight examples demonstrating the impact of cut point selection on exposure assignment, and evaluate potential impacts of such selection on epidemiologic studies of the electric work environment. In conclusion, novel methods allowed for consistent exposure estimates that move from qualitative to quantitative measures in this population-based JEM. Overlapping ranges of median exposure in various categories reflect our limited knowledge about this exposure.

  10. Energy saving certificates

    International Nuclear Information System (INIS)

    2005-11-01

    The French ministry of economy, finances and industry and the French agency of environment and energy mastery (Ademe) have organized on November 8, 2005, a colloquium for the presentation of the energy saving certificates, a new tool to oblige the energy suppliers to encourage their clients to make energy savings. This document gathers the transparencies presented at this colloquium about the following topics: state-of-the-art and presentation of the energy saving certificates system: presentation of the EEC system, presentation of the EEC standard operations; the energy saving certificates in Europe today: energy efficiency commitment in UK, Italian white certificate scheme, perspectives of the different European systems. (J.S.)

  11. Energy-saving decomposition and power consumption forecast: The case of liaoning province in China

    Energy Technology Data Exchange (ETDEWEB)

    He, Y.X.; Zhao, Y.S.; Wang, Y.J. [School of Business Administration, North China Electric Power University, Zhu Xin Zhuang, Bei Nong Lu No. 2, Changping District, Beijing (China); Zhang, S.L. [Finance Department, Nanning Power Supply Bureau, Xingguang Street No. 43, Nanning, Guangxi Autonomous Region (China); Li, F.R. [University of Bath, Bath, BA2 7AY (United Kingdom)

    2011-01-15

    To achieve sustainable development of the society, the People's Republic of China (PRC) proposed in its 11th Five-Year Plan for National Economic and Social Development Program a shift in energy-saving target of decreasing energy intensity by 20% in 2010 compared with that of 2005. Liaoning province is one of the oldest industrial bases in China. Policymakers are often confronted with problems relating to adjustment in the development pattern as a means to secure steady economic growth. The power industry is a fundamental energy industry; it plays an important role in realizing of energy-saving targets. Based on the input-output model, this paper sets extensive, planning and 20% energy-saving scenarios in order to analyze energy-saving and power consumption situations for Liaoning by 2010. Through extensive simulations, the levels of energy-saving and power demand under different scenarios are obtained. Results from the analysis show that under the premises of adjusting the ratio of investment and consumption, optimizing products structure, and improving energy use efficiency, it is possible to achieve the proposed energy-saving target. Liaoning's power consumption can maintain a stable growth trend in the future. The percentage of electricity to the total energy use can also increase to 16% in 2010. (author)

  12. Relationships between the Brook Street Terrane and Median Tectonic Zone (Median Batholith) : evidence from Jurassic conglomerates

    International Nuclear Information System (INIS)

    Tulloch, A.J.; Kimbrough, D.L.; Landis, C.A.; Mortimer, N.; Johnston, M.R.

    1999-01-01

    U-Pb zircon ages of 237-180 Ma and c. 280 Ma of seven granitoid clasts from the Rainy River Conglomerate which lies within the eastern Median Tectonic Zone (Median Batholith) in Nelson, and the Barretts Formation of the Brook Street Terrane in Southland, constrain the depositional ages of both units to be no older than c. 180-200 Ma (Early Jurassic). The minimum age of the Rainy River Conglomerate is constrained by the 147 +2 -1 Ma (Latest Jurassic) emplacement age of the One Mile Gabbronorite (new name: previously western Buller Diorite). The ages and chemistry of five of the granitoid clasts are broadly compatible with derivation from rocks that are now represented by Triassic plutons of the Median Tectonic Zone (Median Batholith), although ages as young as 180 Ma are slightly outside the range of the latter as currently exposed in New Zealand. The age (273-290 Ma, 237 +/- 3 Ma) and chemistry of the other two clasts (one each from Rainy River Conglomerate and Barretts Formation) suggest derivation from the Brook Street Terrane. Similarity in stratigraphic age, depositional characteristics, granitoid clast ages and composition between Rainy River Conglomerate and Barretts Formation suggests that they are broadly correlative and collectively overlapped a combined Brook Street Terrane - Median Batholith (MTZ) before the Late Jurassic (147 +2 -1 Ma). Sedimentary overlap may also have continued across to Middle Jurassic conglomeratic strata in the Murihiku Terrane to the east of the Brook Street Terrane. A U-Pb zircon age of 261 +/- 2 Ma is reported for Pourakino Trondhjemite of the Brook Street Terrane. (author). 56 refs., 10 figs., 4 tabs

  13. Online Energy Management of Plug-In Hybrid Electric Vehicles for Prolongation of All-Electric Range Based on Dynamic Programming

    Directory of Open Access Journals (Sweden)

    Zeyu Chen

    2015-01-01

    Full Text Available The employed energy management strategy plays an important role in energy saving performance and exhausted emission reduction of plug-in hybrid electric vehicles (HEVs. An application of dynamic programming for optimization of power allocation is implemented in this paper with certain driving cycle and a limited driving range. Considering the DP algorithm can barely be used in real-time control because of its huge computational task and the dependence on a priori driving cycle, several online useful control rules are established based on the offline optimization results of DP. With the above efforts, an online energy management strategy is proposed finally. The presented energy management strategy concerns the prolongation of all-electric driving range as well as the energy saving performance. A simulation study is deployed to evaluate the control performance of the proposed energy management approach. All-electric range of the plug-in HEV can be prolonged by up to 2.86% for a certain driving condition. The energy saving performance is relative to the driving distance. The presented energy management strategy brings a little higher energy cost when driving distance is short, but for a long driving distance, it can reduce the energy consumption by up to 5.77% compared to the traditional CD-CS strategy.

  14. Median and ulnar neuropathies in university guitarists.

    Science.gov (United States)

    Kennedy, Rachel H; Hutcherson, Kimberly J; Kain, Jennifer B; Phillips, Alicia L; Halle, John S; Greathouse, David G

    2006-02-01

    Descriptive study. To determine the presence of median and ulnar neuropathies in both upper extremities of university guitarists. Peripheral nerve entrapment syndromes of the upper extremities are well documented in musicians. Guitarists and plucked-string musicians are at risk for entrapment neuropathies in the upper extremities and are prone to mild neurologic deficits. Twenty-four volunteer male and female guitarists (age range, 18-26 years) were recruited from the Belmont University School of Music and the Vanderbilt University Blair School of Music. Individuals were excluded if they were pregnant or had a history of recent upper extremity or neck injury. Subjects completed a history form, were interviewed, and underwent a physical examination. Nerve conduction status of the median and ulnar nerves of both upper extremities was obtained by performing motor, sensory, and F-wave (central) nerve conduction studies. Descriptive statistics of the nerve conduction study variables were computed using Microsoft Excel. Six subjects had positive findings on provocative testing of the median and ulnar nerves. Otherwise, these guitarists had normal upper extremity neural and musculoskeletal function based on the history and physical examinations. When comparing the subjects' nerve conduction study values with a chart of normal nerve conduction studies values, 2 subjects had prolonged distal motor latencies (DMLs) of the left median nerve of 4.3 and 4.7 milliseconds (normal, DMLs are compatible with median neuropathy at or distal to the wrist. Otherwise, all electrophysiological variables were within normal limits for motor, sensory, and F-wave (central) values. However, comparison studies of median and ulnar motor latencies in the same hand demonstrated prolonged differences of greater than 1.0 milliseconds that affected the median nerve in 2 additional subjects, and identified contralateral limb involvement in a subject with a prolonged distal latency. The other 20

  15. Energy Saving Potential of PCMs in Buildings under Future Climate Conditions

    Directory of Open Access Journals (Sweden)

    Abdo Abdullah Ahmed Gassar

    2017-11-01

    Full Text Available Energy consumption reduction under changing climate conditions is a major challenge in buildings design, where excessive energy consumption creates an economic and environmental burden. Improving thermal performance of the buildings through support applying phase change material (PCM is a promising strategy for reducing building energy consumption under future climate change. Therefore, this study aims to investigate the energy saving potentials in buildings under future climate conditions in the humid and snowy regions in the hot continental and humid subtropical climates of the east Asia (Seoul, Tokyo and Hong Kong when various PCMs with different phase change temperatures are applied to a lightweight building envelope. Methodology in this work is implemented in two phases: firstly, investigation of energy saving potentials in buildings through inclusion of three types of PCMs with different phase temperatures into the building envelop separately and use weather file in the present (2017; and, secondly, evaluation of the effect of future climate change on the performance of PCMs by analyzing energy saving potentials of PCMs with 2020, 2050 and 2080 weather data. The results show that the inclusion of PCM into the building envelope is a promising strategy to increase the energy performance in buildings during both heating and cooling seasons in Seoul, Tokyo and Hong Kong under future climate conditions. The energy savings achieved by using PCMs in those regions are electricity savings of 4.48–8.21%, 3.81–9.69%, and 1.94–5.15%, and gas savings of 1.65–16.59%, 7.60–61.76%, and 62.07–93.33% in Seoul, Tokyo and Hong Kong, respectively, for the years 2017, 2020, 2050 and 2080. In addition, BioPCM and RUBITHERMPCM are the most efficient for improving thermal performance and saving energy in buildings in the tested regions and years.

  16. REMINDER Saved Leave Scheme (SLS) : Transfer of leave to saved leave accounts

    CERN Multimedia

    HR Division

    2002-01-01

    Under the provisions of the voluntary saved leave scheme (SLS), a maximum total of 10 days'*) annual and compensatory leave (excluding saved leave accumulated in accordance with the provisions of Administrative Circular No. 22B) can be transferred to the saved leave account at the end of the leave year (30 September). We remind you that, since last year, unused leave of all those taking part in the saved leave scheme at the closure of the leave-year accounts is transferred automatically to the saved leave account on that date. Therefore, staff members have no administrative steps to take. In addition, the transfer, which eliminates the risk of omitting to request leave transfers and rules out calculation errors in transfer requests, will be clearly shown in the list of leave transactions that can be consulted in EDH from October 2002 onwards. Furthermore, this automatic leave transfer optimizes staff members' chances of benefiting from a saved leave bonus provided that they are still participants in the schem...

  17. Specifics of energy-saving technologies in electrical power supply systems of operating industrial enterprises

    OpenAIRE

    Кирисов, Игорь Геннадиевич; Овчаренко, Татьяна Ивановна

    2014-01-01

    В статье рассмотрены особенности разных энергосберегающих технологий, которые можно применить в системах электроснабжения промышленных предприятий. Проведены расчеты, подтверждающие целесообразность замены недозагруженных асинхронных двигателей на двигатели меньшей мощности. The paper deals with the speci cs of different energy-saving technologies that can be applied in electrical power supply systems of industrial enterprises. The paper presents calculations that corroborate ...

  18. Cost Savings for Manufacturing Lithium Batteries in a Flexible Plant

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Paul A.; Ahmed, Shabbir; Gallagher, Kevin G.; Dees, Dennis W.

    2015-06-01

    The flexible plant postulated in this study would produces types of batteries for electric-drive vehicles of the types hybrid (HEV), 10-mile range and 40-mile range plug-in hybrids (PHEV) and a 150-mile range battery-electric (EV). The annual production rate of the plant is 235,000 per year (30,000 EV batteries and 100,000 HEV batteries). The unit cost savings as calculated with the Argonne BatPaC model for this flex plant vs. dedicated plants range from 8% for the EV battery packs to 23% for the HEV packs including the battery management systems (BMS). The investment cost savings are even larger, ranging from 21% for EVs to 43% for HEVs. The costs of the 1.0-kWh HEV batteries are projected to approach $710 per unit and that of the EV batteries $228 per kWh with the most favorable cell chemistries and including the BMS. The best single indicator of the cost of producing lithium-manganate spinel/graphite batteries in a flex plant is the total cell area of the battery. For the four batteries studied, the price range is $20-24 per m2 of cell area including the cost of the BMS, averaging $21 per m2 for the entire flex plant.

  19. Energy savings by implementation of light quality LED lighting. Final report; Implementering af energibesparelser ved benyttelse af hoejkvalitets LED belysning. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Dam-Hansen, C.; Thorseth, A.; Poulsen, Peter

    2010-03-15

    The project developed two new LED light sources and systems, emphasising the potential of LED technology for energy savings and lighting quality. A LED light source for display case lighting, replacing incandescent lamps, was successfully installed in the Treasury at Rosenborg Castle in Copenhagen, Denmark, and it was decided to extend the solution in 2010. Electricity savings of 74% were achieved. LED light sources replacing halogen bulbs in cooker hoods reduce electricity consumption by 69% and ensure even lighting of the entire working surface with about 500 lux at all cooking areas. Furthermore, a new LED optics system was patented. (ln)

  20. Measuring industrial energy savings

    International Nuclear Information System (INIS)

    Kelly Kissock, J.; Eger, Carl

    2008-01-01

    Accurate measurement of energy savings from industrial energy efficiency projects can reduce uncertainty about the efficacy of the projects, guide the selection of future projects, improve future estimates of expected savings, promote financing of energy efficiency projects through shared-savings agreements, and improve utilization of capital resources. Many efforts to measure industrial energy savings, or simply track progress toward efficiency goals, have had difficulty incorporating changing weather and production, which are frequently major drivers of plant energy use. This paper presents a general method for measuring plant-wide industrial energy savings that takes into account changing weather and production between the pre and post-retrofit periods. In addition, the method can disaggregate savings into components, which provides additional resolution for understanding the effectiveness of individual projects when several projects are implemented together. The method uses multivariable piece-wise regression models to characterize baseline energy use, and disaggregates savings by taking the total derivative of the energy use equation. Although the method incorporates search techniques, multi-variable least-squares regression and calculus, it is easily implemented using data analysis software, and can use readily available temperature, production and utility billing data. This is important, since more complicated methods may be too complex for widespread use. The method is demonstrated using case studies of actual energy assessments. The case studies demonstrate the importance of adjusting for weather and production between the pre- and post-retrofit periods, how plant-wide savings can be disaggregated to evaluate the effectiveness of individual retrofits, how the method can identify the time-dependence of savings, and limitations of engineering models when used to estimate future savings

  1. 76 FR 16477 - General Reporting and Recordkeeping by Savings Associations and Savings and Loan Holding Companies

    Science.gov (United States)

    2011-03-23

    ... Savings Associations and Savings and Loan Holding Companies AGENCY: Office of Thrift Supervision (OTS...), 12 CFR 562.4 (audit of savings association, savings and loan holding company, or affiliate), 12 CFR... the savings association), 12 CFR 584.1(f) (books and records of each savings and loan holding company...

  2. Will Renewable Energy Save Our Planet?

    Science.gov (United States)

    Bojić, Milorad

    2010-06-01

    This paper discusses some important fundamental issues behind application of renewable energy (RE) to evaluate its impact as a climate change mitigation technology. The discussed issues are the following: definition of renewable energy, concentration of RE by weight and volume, generation of electrical energy and its power at unit area, electrical energy demand per unit area, life time approach vs. layman approach, energy return time, energy return ratio, CO2 return time, energy mix for RES production and use, geographical distribution of RES use, huge scale of energy shift from RES to non-RES, increase in energy consumption, Thermodynamic equilibrium of earth, and probable solutions for energy future of our energy and environmental crisis of today. The future solution (that would enable to human civilization further welfare, and good living, but with lower release of CO2 in atmosphere) may not be only RES. This will rather be an energy mix that may contain nuclear energy, non-nuclear renewable energy, or fossil energy with CO2 sequestration, efficient energy technologies, energy saving, and energy consumption decrease.

  3. Investing EU ETS auction revenues into energy savings

    Energy Technology Data Exchange (ETDEWEB)

    Sijm, J.P.M.; Boonekamp, P.G.M. [ECN Policy Studies, Petten (Netherlands); Summerton, P.; Pollitt, H.; Billington, S. [Cambridge Econometrics CE, Cambridge (United Kingdom)

    2013-05-15

    The overall objective of this study is to analyse the effects of using EU ETS auction revenues to stimulate investments in energy savings in three key target sectors, i.e. Households, Tertiary and Industry (including both ETS and non-ETS industrial installations). The scenarios used refer basically to the situation before the recent agreement on the Energy Efficiency Directive (EED) and include (a mixture of) different policy options to enhance energy savings in the target sectors, in particular (1) reducing the ETS cap, (2) introducing an Energy Efficiency Obligation (EEO) for energy suppliers or distributors, and/or (3) using ETS auction revenues to support additional (private) investments in raising energy efficiency. In order to meet this objective a variety of different policy scenarios have been defined and analysed by means of the 'Energy-Environment-Economy Model for Europe (E3ME)'. The study presents and discusses a large variety of scenario modelling results by the year 2020 at the EU27 level. These results refer to, among others, energy savings, GHG emissions, the ETS carbon price, household electricity bills and to changes in some macro- or socio-economic outcomes such as GDP, inflation, employment or international trade. Finally, the study discusses some policy findings and implications, including options to enhance the effectiveness of some EE policies, in particular those having a potential adverse effect on the ETS carbon price.

  4. Advertising energy saving programs: The potential environmental cost of emphasizing monetary savings.

    Science.gov (United States)

    Schwartz, Daniel; Bruine de Bruin, Wändi; Fischhoff, Baruch; Lave, Lester

    2015-06-01

    Many consumers have monetary or environmental motivations for saving energy. Indeed, saving energy produces both monetary benefits, by reducing energy bills, and environmental benefits, by reducing carbon footprints. We examined how consumers' willingness and reasons to enroll in energy-savings programs are affected by whether advertisements emphasize monetary benefits, environmental benefits, or both. From a normative perspective, having 2 noteworthy kinds of benefit should not decrease a program's attractiveness. In contrast, psychological research suggests that adding external incentives to an intrinsically motivating task may backfire. To date, however, it remains unclear whether this is the case when both extrinsic and intrinsic motivations are inherent to the task, as with energy savings, and whether removing explicit mention of extrinsic motivation will reduce its importance. We found that emphasizing a program's monetary benefits reduced participants' willingness to enroll. In addition, participants' explanations about enrollment revealed less attention to environmental concerns when programs emphasized monetary savings, even when environmental savings were also emphasized. We found equal attention to monetary motivations in all conditions, revealing an asymmetric attention to monetary and environmental motives. These results also provide practical guidance regarding the positioning of energy-saving programs: emphasize intrinsic benefits; the extrinsic ones may speak for themselves. (c) 2015 APA, all rights reserved).

  5. Primary energy savings in desiccant and evaporative cooling-assisted 100% outdoor air system combined with a fuel cell

    International Nuclear Information System (INIS)

    Kim, Min-Hwi; Dong, Hae-Won; Park, Joon-Young; Jeong, Jae-Weon

    2016-01-01

    Highlights: • A LD-IDECOAS integrated with a PEMFC was proposed. • A pilot system was installed and tested during cooling operation. • The proposed system powered by the PEMFC saved 21% of the primary energy consumption during cooling. - Abstract: The main purpose of this study involved investigating the primary energy saving potential of a liquid desiccant and evaporative cooling-assisted 100% outdoor air system (LD-IDECOAS) integrated with a proton exchange membrane fuel cell (PEMFC). During the cooling season, the heat produced by the PEMFC was used to regenerate a weak desiccant solution, and the electricity generated was used to operate the LD-IDECOAS. A pilot LD-IDECOAS powered by a PEMFC was installed and operated in an office space to experimentally verify the annual operating energy savings of the proposed system. The findings indicated that the heat reclaimed from the PEMFC saved 42% of the desiccant solution regenerating energy when compared to that in the case of a conventional gas-fired water heater. The results also suggested that the LD-IDECOAS combined with a PEMFC consumed 21% less primary energy when compared with that of a system powered by grid electricity and a conventional gas-fired water heater.

  6. Energy saving analysis on mine-water source heat pump in a residential district of Henan province, central China

    Science.gov (United States)

    Wang, Hong; Duan, Huanlin; Chen, Aidong

    2018-02-01

    In this paper, the mine-water source heat pump system is proposed in residential buildings of a mining community. The coefficient of performance (COP) and the efficiency of exergy are analyzed. The results show that the COP and exergy efficiency of the mine-water source heat pump are improved, the exergy efficiency of mine-water source heat pump is more than 10% higher than that of the air source heat pump.The electric power conservation measure of “peak load shifting” is also emphasized in this article. It shows that itis a very considerable cost in the electric saving by adopting the trough period electricity to produce hot water. Due to the proper temperature of mine water, the mine-watersource heat pump unit is more efficient and stable in performance, which further shows the advantage of mine-water source heat pump in energy saving and environmental protection. It provides reference to the design of similar heat pump system as well.

  7. Electrical energy saving in motors and frequency variators; Ahorro de energia electrica en motores y variadores de frecuencia

    Energy Technology Data Exchange (ETDEWEB)

    Garcia Neri, Roger [Comision Federal de Electricidad (CFE) (Mexico)

    2005-07-01

    The necessity of saving energy is urgent and undeniable. We must already begin with the rational use of energy. Which is obtaining the maximum benefit of the consumed energy and of the necessary facilities for its generation, transmission and use. Guaranteeing at the same time an operation free of interferences or interruptions for the users. The electricity in alternating current does not allow its storage, reason why it is necessary to generate and distribute it at the precise moment when it is required. This forces to determine the proportions of the generation facilities, to be able to feed the periods of maximum demand called {sup p}eaks{sup .} It is this very point where the problem of the inappropriate use of the electrical energy starts. The energy waste is self-evident during the periods of low demand because of the low efficiency of the sub-utilized facilities. Electrical motors of the induction type use approximately more than 60% of the energy in the industry. If we use high efficiency motors instead of standard motors, a better advantage of the energy demanded from Comision Federal de Electricidad (CFE) is obtained. [Spanish] Es impostergable e innegable la necesidad de ahorrar energia. Tenemos que empezar ya con el uso racional de la energia: Obtener el maximo beneficio de la energia consumida y de las instalaciones necesarias para su generacion, transmision y utilizacion. Garantizando a los usuarios un funcionamiento sin interferencias o interrupciones. La electricidad en corriente alterna no permite su almacenamiento, por lo que es necesario generarla y distribuirla en el momento preciso en que es requerida. Esto obliga a dimensionar las instalaciones de generacion, para poder alimentar los periodos de maxima demanda llamados pico. Desde esta parte inicia el problema de la mala utilizacion de la energia electrica. Ya que en los periodos de baja demanda, las instalaciones se encuentran subutilizadas y si su eficiencia es muy baja, el desperdicio de

  8. From rationing to energy saving certificates. Four decades of power demand control in France and United Kingdom

    International Nuclear Information System (INIS)

    Pautard, Eric

    2012-01-01

    From 'saving energy' awareness campaign to financial incentives for efficient technologies, from rationing to energy efficiency commitment, from monopolistic public management to compelling involvement of the electricity-supply market, from economic stakes to ecological issues, Demand-Side Management policies have changed over time. This paper analyzes this historical background in order to examine the effects of the electricity market deregulation in France and United Kingdom

  9. Preliminary Study of Perception and Consumer Behaviour Towards Energy Saving for Household Appliances: A Case of Makassar

    Science.gov (United States)

    Syam Akil, Yusri; Mangngenre, Saiful; Mawar, Sri; Amar, Kifayah

    2018-03-01

    Electricity load has tendency to increase over the time. Therefore, efforts to maintain a balance between electricity supply and demand such as increasing energy saving related to the use of home electricity appliances are urgently needed. In general, one of the household appliances which consumes relatively high electricity energy is refrigerator. The purpose of this study is to analyze residential consumers perceptions and their behaviours about electricity energy saving in relation to the usage of household appliances in Makassar, Indonesia particularly for refrigerator. Moreover, typical relationship between perceptions and consumers behaviours is also analyzed by composed two regression models, namely model for usage behaviour (UREFm model) and model for habitual behaviour (HREFm model) by using general perception, specific perception, and external factors as explanation variables. To collect data, a questionnaire was designed for survey which involved 40 respondents as a preliminary study and then statistical tests including regression analysis were applied to analyze usable data. The target of respondent was an owner of a house in Makassar with installed power capacity at least 900 VA. Reliability test shown that all items in the developed questionnaire can be used for main survey as obtained Cronbach’s alpha values were above 0.6. Evaluation for consumers perceptions on energy saving in relation to demographic aspect using mean and Standard Deviation values indicated some significant differences. Other results regarding regression analysis shown that both composed models were well validated and had quite good fitness degree with adjusted R-squared values around 49.31% for UREFm model and 80.90% for HREFm model. Among considered variables, specific perception, and external factors were found have significant influence to the usage and habitual behaviours of consumers as confirmed by their p-values in each model below 0.05. Findings of this research can be

  10. Analysis of energy saving performance for household refrigerator with thermal storage of condenser and evaporator

    International Nuclear Information System (INIS)

    Cheng, Wen-long; Ding, Miao; Yuan, Xu-dong; Han, Bing-Chuan

    2017-01-01

    Highlights: • A novel refrigerator with both HSC and CSE is proposed. • The operational characteristics of novel refrigerator is analyzed. • The comparison of CSE, HSC and DES refrigerators is analyzed. • DES refrigerator has a largest off-time to on-time ratio of 4.3. • DES refrigerator has the best electrical energy saving performance (32%). - Abstract: The heat transfer performances of evaporators and condensers significantly affect the efficiency of household refrigerators. For enhancing heat transfer of the condensers and evaporators, a novel dual energy storage (DES) refrigerator with both heat storage condenser (HSC) and cold storage evaporator (CSE) is proposed. The performance comparison of three kinds of energy storage refrigerators: HSC refrigerator, CSE refrigerator and DES refrigerator is analyzed by establishing dynamic simulation models. According to the simulation results, the DES refrigerator combines the advantage of HSC refrigerator and CSE refrigerator, it has more balanced operational cycle and higher evaporation pressure and temperature. The DES refrigerator shows a best energy saving performance among the three energy storage refrigerators with largest off-time to on-time ratio of 4.3 and the electrical consumption saving can reach 32%, which is greater than the sum (28%) of the other two kinds of energy storage refrigerators.

  11. The likely market potential for electricity saving ASD devices

    International Nuclear Information System (INIS)

    Sparow, F.T.; McKenzie, L.

    1993-01-01

    Many utility demand-side management (DSM) programs encourage the adoption of adjustable speed drives (ASD) in the industrial and commercial sectors, since such devices save KW and KWh. The term open-quotes adjustable speed drives close-quote is used to refer to any device which allows the speed of the motor to be adjusted to better match process requirements. Thus, motor input control devices, such as electronic adjustable speed drives for AC motors (i.e., adjustable frequency drives (AFD)), voltage controlled DC motors, and the use of floating pressure setpoint controls, or other devices which better control on/off compressor operation, would be considered ASD devices. Also included would be motor technologies, such as multi-speed windings, etc., which allow the synchronous speed of the motor to be altered. Not included in this definition would be mechanical systems such as gear boxes, friction disks, etc., which maintain motor speed, but alter the drive r.p.m. to the equipment. The importance of the distinction is that ASDs, as defined above, have the potential to substantially reduce KW and KWh consumption if the equipment duty cycle is varying, while mechanical drive r.p.m. varying devices don't

  12. Saving energy. [Metal Coating With Infrared Dryers

    Energy Technology Data Exchange (ETDEWEB)

    Schmid, K

    1981-01-01

    One way of saving energy in metal coating is by using electrically heated infrared dryers with medium-wave radiation (2 to 3 ..mu..m). The absorbing capacity of varnishes and plastic coatings is >90% in this range so that the radiation energy is almost completely transformed into heat. Medium-wave radiation sources have a much higher service life than short-wave sources (30.000 hours of operation) and do not require cooling; compared with long-wave sources, they have a higher heat transfer and thus much shorter drying times. The main fields of application, a cost example, and practical examples among the customers of Messrs. Eisenmann are presented.

  13. 76 FR 31680 - General Reporting and Recordkeeping by Savings Associations and Savings and Loan Holding Companies

    Science.gov (United States)

    2011-06-01

    ... Savings Associations and Savings and Loan Holding Companies AGENCY: Office of Thrift Supervision (OTS... Savings and Loan Holding Companies. OMB Number: 1550-0011. Form Number: N/A. Description: This information...), 12 CFR 562.4 (audit of savings association, savings and loan holding company, or affiliate), 12 CFR...

  14. Laying Stress on Energy-Saving and Environmental Protection of Thermal Generation

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ The most attraetive spot of the 11th Five-Year Plan is to change China's present mode of cconomic growth and take a road of circulative cconomy based on effective utilization of resources and environmental protection. Electric power as a basic industry,energy conservation and environmental protection will become one of its working cmphases in a period of time to come. In this connection, the journalist (Zhao Ran) from China Electric Power has exclusively interviewed Tang Yunlin, the former president of the China Electric Power Planning and Engineering Institute. He thought that the most important thing for power industry to save energy and protect environment is to bring about the energy conservation and environmental protection in thermal power plants rather than first devclop hydropower, nuclear power and renewable energy. His viewpoints and suggestions have been recognized by many insiders.

  15. 12 CFR 583.21 - Savings association.

    Science.gov (United States)

    2010-01-01

    ... AFFECTING SAVINGS AND LOAN HOLDING COMPANIES § 583.21 Savings association. The term savings association means a Federal savings and loan association or a Federal savings bank chartered under section 5 of the Home Owners' Loan Act, a building and loan, savings and loan or homestead association or a cooperative...

  16. The research and application of electricity economic boom model under the constraint of energy conservation and emission reduction

    Science.gov (United States)

    Chen, Guangyan; Xia, Huaijian; Chen, Meiling; Wang, Dong; Jia, Sujin

    2017-10-01

    Energy saving and emission reduction policies affects the development of high power industry, thereby affecting electricity demand, so the study of the electricity industry boom helps to master the national economy. This paper analyses the influence of energy saving and emission reduction on power generation structure and pollutant emission in power industry. Through the construction of electricity market composite boom index to indicate electricity boom, using boom index to study volatility characteristics and trend of electricity market. Here we provide a method for the enterprise and the government, that it can infer the overall operation of the national economy situation from power data.

  17. Verification of electricity savings through energy-efficient train management - Energy data base for traction units - Annex 5; Verifizierung der Stromeinsparung durch energieeffizientes Zugsmanagement - Anhang 5: Energiedatenbank Traktion

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, M.; Lerjen, M.; Menth, S. [emkamatik GmbH, Wettingen (Switzerland); Luethi, M. [Swiss Federal Insitute of Technology (ETHZ), Institute for Transport Planning and Systems (IVT), Zuerich (Switzerland); Tuchschmid, M. [SBB AG, BahnUmwelt-Center, 3000 Bern (Switzerland)

    2009-11-15

    This appendix to a final report for the Swiss Federal Office of Energy (SFOE) takes a look at how various data sources on the energy consumption of the SBB's traction units can be combined into an energy-data basis. In this way, the considerable amount of work previously involved in combining and correlating data can be avoided. The aims being followed in the realisation of the traction data base are examined and discussed. The data base will provide the basis for the manual detail analysis of energy consumption within the framework of the overall efforts to save electricity using efficient train management.

  18. MEDIAN: Wireless broadband LAN for multimedia applications

    NARCIS (Netherlands)

    Vliet, P.J. van

    1998-01-01

    MEDIAN is one of the projects in the mobile domain of the Advanced Communications Technologies and Services (ACTS) programme of the European Commission. The main obiective of the MEDIAN project is to evaluate and implement a high speed Wireless Customer Premises / Local Area Network (WCPN/WLAN)

  19. On Preliminary Test Estimator for Median

    OpenAIRE

    Okazaki, Takeo; 岡崎, 威生

    1990-01-01

    The purpose of the present paper is to discuss about estimation of median with a preliminary test. Two procedures are presented, one uses Median test and the other uses Wilcoxon two-sample test for the preliminary test. Sections 3 and 4 give mathematical formulations of such properties, including mean square errors with one specified case. Section 5 discusses their optimal significance levels of the preliminary test and proposes their numerical values by Monte Carlo method. In addition to mea...

  20. Vehicle to Grid regulation services of electric delivery trucks: Economic and environmental benefit analysis

    International Nuclear Information System (INIS)

    Zhao, Yang; Noori, Mehdi; Tatari, Omer

    2016-01-01

    Highlights: • Potential net present revenues of electric truck based V2G regulation services are investigated. • GHG emission mitigation of V2G regulation services provided by electric trucks are quantified. • The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed. • V2G regulation services for electric trucks could yield considerable revenues and GHG emission savings. - Abstract: Concerns regarding the fuel costs and climate change impacts associated with petroleum combustion are among the main driving factors for the adoption of electric vehicles. Future commercial delivery truck fleets may include Battery Electric Vehicles (BEVs) and Extended Range Electric Vehicles (EREVs); in addition to savings on fuel and maintenance costs, the introduction of these grid accessible electric vehicles will also provide fleet owners with possible Vehicle to Grid (V2G) opportunities. This study investigates the potential net present revenues and greenhouse gas (GHG) emission mitigation of V2G regulation services provided by electric trucks in a typical fleet. The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed and compared to those of traditional diesel trucks. To account for uncertainties, possible ranges for key parameters are considered instead of only considering fixed single data values for each parameter. The results of this research indicate that providing V2G regulation services for electric trucks could yield considerable additional revenues ($20,000–50,000) and significant GHG emission savings (approximately 300 ton CO_2) compared to conventional diesel trucks.

  1. Saving energy resources during heat treatment - the most important problem of the branch

    Energy Technology Data Exchange (ETDEWEB)

    Zadernovskiy, V V; Firger, I V

    1980-01-01

    Natural gas fired thermal furnaces expend significantly less fuel than electric furnaces with an equal quality of metal heating. An important reserve in power reserve economy is the use of the forging heat in an article for heat treatment (TOB), where besides the power resources, metal is also saved as a result of the reduction in the volume of heating means and production spaces. From the experience in the progressive enterprises of the branch, in a number of cases it is possible to combine heating for plastic deformation with heating for primary or secondary heat treatment. Other measures are examined which save power resources in heat treatment: the use of thermal furnaces for aerodynamic heating, the use of local heat treatment, the reduction in the duration of the heat treatment processes, savings in the power carriers during heat treatment in furnaces with a roll out hearth. Fibrous refractory materials are being used more and more as fettling materials in the construction of thermal furnaces.

  2. Evaluation of all-electric secondary power for transport aircraft

    Science.gov (United States)

    Murray, W. E.; Feiner, L. J.; Flores, R. R.

    1992-01-01

    This report covers a study by Douglas Aircraft Company (DAC) of electrical power systems for advanced transport aircraft based upon an all-electric design concept. The concept would eliminate distributed hydraulic and pneumatic secondary power systems, and feature an expanded secondary electrical power system redesigned to supply power to the loads customarily supplied by hydraulic or pneumatic power. The initial study was based on an advanced 20-kHz electrical power transmission and distribution system, using a system architecture supplied by NASA-Lewis Research Center for twin-engine aircraft with many advanced power conversion concepts. NASA-LeRC later requested DAC to refocus the study on 400-Hz secondary power distribution. Subsequent work was based on a three-engine MD-11 aircraft, selected by DAC as a baseline system design that would provide data for the comparative cost/benefit analysis. The study concluded that the 20-kHz concept produced many expected benefits, and that the all-electric trijet weight savings on hardware redesign would be 2,304 pounds plus a 2.1-percent fuel reduction and resized for a total weight reduction of 11,000 pounds. Cost reductions for a fleet of 800 aircraft in a 15-year production program were estimated at $76.71 million for RDT&E; $2.74 million per aircrat for production; $9.84 million for nonrecurring expenses; $120,000 per aircraft for product support; and $300,000 per aircraft per year for operating and maintenance costs, giving a present value of $1.914 billion saved or a future value of $10.496 billion saved.

  3. Exemplary role of the government in the domain of energy saving

    International Nuclear Information System (INIS)

    2005-09-01

    The objectives of the French energy policy is a progressive reduction of the energy intensity and a progressive abatement of greenhouse gas emissions. In this context, the government administrations wish to show the example with the implementation of exemplary actions in 3 domains: use of low consumption and low pollution vehicles, renovation of administrative buildings and use of low energy consumption equipments (lighting systems, lifts, space heating systems and boilers, windows, appliances and computers), and saving paper. Also, the administrations have to analyze the commercial offers for the purchase of electricity coming from renewable energy sources and for the improvement of the energy efficiency and the mastery of electricity demand. (J.S.)

  4. The Program Administrator Cost of Saved Energy for Utility Customer-Funded Energy Efficiency Programs

    Energy Technology Data Exchange (ETDEWEB)

    Billingsley, Megan A.; Hoffman, Ian M.; Stuart, Elizabeth; Schiller, Steven R.; Goldman, Charles A.; LaCommare, Kristina

    2014-03-19

    End-use energy efficiency is increasingly being relied upon as a resource for meeting electricity and natural gas utility system needs within the United States. There is a direct connection between the maturation of energy efficiency as a resource and the need for consistent, high-quality data and reporting of efficiency program costs and impacts. To support this effort, LBNL initiated the Cost of Saved Energy Project (CSE Project) and created a Demand-Side Management (DSM) Program Impacts Database to provide a resource for policy makers, regulators, and the efficiency industry as a whole. This study is the first technical report of the LBNL CSE Project and provides an overview of the project scope, approach, and initial findings, including: • Providing a proof of concept that the program-level cost and savings data can be collected, organized, and analyzed in a systematic fashion; • Presenting initial program, sector, and portfolio level results for the program administrator CSE for a recent time period (2009-2011); and • Encouraging state and regional entities to establish common reporting definitions and formats that would make the collection and comparison of CSE data more reliable. The LBNL DSM Program Impacts Database includes the program results reported to state regulators by more than 100 program administrators in 31 states, primarily for the years 2009–2011. In total, we have compiled cost and energy savings data on more than 1,700 programs over one or more program-years for a total of more than 4,000 program-years’ worth of data, providing a rich dataset for analyses. We use the information to report costs-per-unit of electricity and natural gas savings for utility customer-funded, end-use energy efficiency programs. The program administrator CSE values are presented at national, state, and regional levels by market sector (e.g., commercial, industrial, residential) and by program type (e.g., residential whole home programs, commercial new

  5. Optimal Charging of Electric Vehicles with Trading on the Intraday Electricity Market

    Directory of Open Access Journals (Sweden)

    Ilham Naharudinsyah

    2018-06-01

    Full Text Available Trading on the energy market is a possible way to reduce the electricity costs of charging electric vehicles at public charging stations. In many European countries, it is possible to trade electricity until shortly before the period of delivery on so called intraday electricity markets. In the present work, the potential for reducing the electricity costs by trading on the intraday market is investigated using the example of the German market. Based on simulations, the authors reveal that by optimizing the charging schedule together with the trading on the intraday electricity market, the costs can be reduced by around 8% compared to purchasing all the required energy from the energy supplier. By allowing the charging station operator to resell the energy to the intraday electricity market, an additional cost reduction of around 1% can be achieved. Besides the potential cost savings, the impacts of the trading unit and of the lead time of the intraday electricity market on the costs are investigated. The authors reveal that the achievable electricity costs can be strongly affected by the lead time, while the trading unit has only a minor effect on the costs.

  6. Geology of Woman Saving Concept

    Directory of Open Access Journals (Sweden)

    Shayesteh Madani

    2014-09-01

    Full Text Available Money is lubricant and an instrument for economic transaction. Money social dimension has increased over time, transforming it from a sole economic instrument to a device for various transactions. Money economic value in society is indicated through different forms, one of which is saving, in the sense of money accumulation and its use under specific future circumstances. Women, who form half of the society, take specific approaches to money and savings. The current research aims to investigate the perspectives and changing attitude strategy to money and saving among married women. The participants of this study include 20 to 70 year-old employed household married women who were observed phenomenologically and interviewed qualitatively on saving through.   The findings of this study demonstrated women perspectives on various types of saving, ways of saving, transfer methods, saving consumption forms and their mechanism. It also revealed that while money is an economic instrument and possess the economic material; attitudes and acts related to money are influenced by social conditions that has consequently turned saving into a social phenomenon.

  7. Effects of a power shortage in the Tokyo metropolitan area on awareness of nuclear power generation and power savings behavior

    International Nuclear Information System (INIS)

    Kitada, Atsuko

    2004-01-01

    The shutdown of a number of nuclear power stations of the Tokyo Electric Power Company in the summer of 2003 caused a power shortage problem in the Tokyo Metropolitan area. To examine the effects of the power shortage, in September 2003 a survey was conducted in the service areas of the Kansai Electric Power Company (Kansai region) and the Tokyo Electric Power Company (Kanto region). This survey was part of a wider opinion survey begun in 1993 concerning nuclear power generation. The results of the September 2003 survey are as follows: The degree of recognition of the power shortage problem in the Metropolitan area was high, with 40% of respondents in the Kansai region and nearly 70% in the Kanto region understanding that the shortage was caused by the shutdown of several nuclear power station. The overall awareness of nuclear power generation was little affected in both the Kansai and Kanto regions, though the sense of a shortage of the generating capacity had been raised slightly. Once respondents knew about the power shortage problem, they estimated the likelihood of an occurrence of large-scale service interruption to be low, nearly at an even chance, and they had been only slightly worried about it, essentially viewing the problem optimistically. In the Kanto region, where public relations activities for power savings had been actively pursued, the frequency of experiencing exposure to such public relations activities was remarkably higher than in the Kansai region. The relation between exposure to public relations activities for power savings and power savings behavior was analyzed using quantification method II. Analysis results suggest that public relations activities for power savings in the Kanto region had the effect of urging power savings behavior. However, the difference in the rate of putting power savings behavior into practice was small between the Kanto and Kansai regions, indicating that public relation activities for power savings in the Kanto

  8. Energy savings for solar heating systems; Solvarmeanlaegs energibesparelser

    Energy Technology Data Exchange (ETDEWEB)

    Furbo, S.; Fan, J.

    2011-01-15

    Energy savings for a number of new solar heating systems in one family houses have been determined by means of information on the energy consumption of the houses before and after installation of the solar heating systems. The investigated solar heating systems are marketed by Velux Danmark A/S, Sonnnenkraft Scandinavia A/S and Batec Solvarme A/S. Solar domestic hot water systems as well as solar combi systems are included in the investigations The houses have different auxiliary energy supply systems: Natural gas boilers, oil fired burners, electrical heating and district heating. Some of the houses have a second auxiliary energy supply system. The collector areas vary from 1.83 m{sup 2} to 9.28 m{sup 2}. Some of the solar heating systems are based on energy units with a new integrated natural gas boiler and a heat storage for the solar heating system. The existing energy systems in the houses are for most of the houses used as the auxiliary energy systems for the solar heating systems. The yearly energy savings for the houses where the only change is the installation of the solar heating system vary from 300 kWh per m{sup 2} solar collector to 1300 kWh per m{sup 2} solar collector. The average yearly energy savings is about 670 kWh per m{sup 2} solar collector for these solar heating systems. The energy savings per m{sup 2} solar collector are not influenced by the solar heating system type, the company marketing the system, the auxiliary energy supply system, the collector area, the collector tilt, the collector azimuth, the energy consumption of the house or the location of the house. The yearly energy savings for the houses with solar heating systems based on energy units including a new natural gas boiler vary from 790 kWh per m{sup 2} solar collector to 2090 kWh per m{sup 2} solar collector. The average yearly energy savings is about 1520 kWh per m{sup 2} solar collector for these solar heating systems. The energy savings per m{sup 2} solar collector for

  9. Energy-saving motor; Energiesparmotor

    Energy Technology Data Exchange (ETDEWEB)

    Lindegger, M.

    2002-07-01

    This report for the Swiss Federal Office of Energy (SFOE) describes the development and testing of an advanced electrical motor using a permanent-magnet rotor. The aims of the project - to study the technical feasibility and market potential of the Eco-Motor - are discussed and the three phases of the project described. These include the calculation and realisation of a 250-watt prototype operating at 230 V, the measurement of the motor's characteristics as well as those of a comparable asynchronous motor on the test bed at the University of Applied Science in Lucerne, Switzerland, and a market study to establish if the Eco-Motor and its controller can compete against normal asynchronous motors. Also, the results of an analysis of the energy-savings potential is made, should such Eco-Motors be used. Detailed results of the three phases of the project are presented and the prospects of producing such motors in Switzerland for home use as well as for export are examined.

  10. Cost-effectiveness of plug-in hybrid electric vehicle battery capacity and charging infrastructure investment for reducing US gasoline consumption

    International Nuclear Information System (INIS)

    Peterson, Scott B.; Michalek, Jeremy J.

    2013-01-01

    Federal electric vehicle (EV) policies in the United States currently include vehicle purchase subsidies linked to EV battery capacity and subsidies for installing charging stations. We assess the cost-effectiveness of increased battery capacity vs. nondomestic charging infrastructure installation for plug-in hybrid electric vehicles as alternate methods to reduce gasoline consumption for cars, trucks, and SUVs in the US. We find across a wide range of scenarios that the least-cost solution is for more drivers to switch to low-capacity plug-in hybrid electric vehicles (short electric range with gasoline backup for long trips) or gasoline-powered hybrid electric vehicles. If more gasoline savings are needed per vehicle, nondomestic charging infrastructure installation is substantially more expensive than increased battery capacity per gallon saved, and both approaches have higher costs than US oil premium estimates. Cost effectiveness of all subsidies are lower under a binding fuel economy standard. Comparison of results to the structure of current federal subsidies shows that policy is not aligned with fuel savings potential, and we discuss issues and alternatives. - Highlights: ► We compare cost of PHEV batteries vs. charging infrastructure per gallon of gasoline saved. ► The lowest cost solution is to switch more drivers to low-capacity PHEVs and HEVs. ► If more gasoline savings is needed, batteries offer a better value than chargers. ► Extra batteries and chargers are both more costly per gal than oil premium estimates. ► Current subsidies are misaligned with fuel savings. We discuss alternatives.

  11. Save Energy: Save Money!

    Science.gov (United States)

    Eccli, Eugene; And Others

    This publication is a collection of inexpensive energy saving tips and home improvements for home owners, particularly in low-income areas or in older homes. Section titles are: (1) Keeping Warm; (2) Getting Heat Where You Need It; (3) Using the Sun; (4) Furnaces, Stoves, and Fireplaces; (5) Insulation and Other Energy Needs; (6) Do-It-Yourself…

  12. Save production: a bottom-up energy model for Dutch industry and agriculture

    International Nuclear Information System (INIS)

    Daniels, B.W.; Dril, A.W.N. van

    2007-01-01

    A new version of the model Save production simulates the development of energy use in the Dutch industry and agriculture, including combined heat and power generation. The model disaggregates national energy consumption into fuel types, industrial sectors, energy functions and energy technologies. Simulation is based on microeconomic investment behavior. Examples of model application show results on the penetration of combined heat and power in relation to policy instruments such as CO 2 prices, electricity price support and investment subsidies. Policies that discriminate on CO 2 emissions result in a slightly more efficient heat and power generation. Tailored to the Dutch situation, Save production is well equipped to generate outlooks for the Dutch industrial and agricultural energy use, and for analyzing the role of policies in detail. Its main strength lies in the middle term simulation of decision-making on energy saving technologies and analysis of policy effects. Specific precautions are required when the model is used for analysis on the longer-term, for simulating extreme policies or for the analysis of extremely fluctuating energy prices. (author)

  13. Contract saving schemes

    NARCIS (Netherlands)

    Ronald, R.; Smith, S.J.; Elsinga, M.; Eng, O.S.; Fox O'Mahony, L.; Wachter, S.

    2012-01-01

    Contractual saving schemes for housing are institutionalised savings programmes normally linked to rights to loans for home purchase. They are diverse types as they have been developed differently in each national context, but normally fall into categories of open, closed, compulsory, and ‘free

  14. Barriers for realisation of energy savings in buildings; Barrierer for realisering af energibesparelser i bygninger

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, O.M.

    2004-07-01

    Many years' efforts within the energy labelling area have shown large saving potentials in heating and use of electricity in buildings. At the same time it has been proved that these saving potentials, even when economically advantageous, only are cashed to a limited extent. The reason to this is ascribed to barriers that meet the individual building owner who wants to start saving energy. Most barriers are known and a lot of these have been sought overcome for some time. The questions are how many barriers still exist, have new barriers arisen and the character of these barriers. On this background the objective of this survey has been to concretize and study the barriers, which are blocking reasonable energy savings. Focus has especially been on barriers for realisation of heating savings, but through a general evaluation of energy savings of barriers other forms of energy saving methods have been taken into consideration. Special interest has been directed towards houses, typically one family houses, which are affected by the Energy Labelling Scheme. The concept barriers include all kinds of barriers, also barriers that not are acknowledged as barriers by the individual house owner, or that on closer inspection turn out to be something else than actual barriers. This note suggests an alternative inertia model, in order to create an idea of the inertness characteristic of the many house owners who understand the message but fail to act on it. (BA)

  15. Differential electricity pricing and energy efficiency in South Africa

    International Nuclear Information System (INIS)

    Kohler, Marcel

    2014-01-01

    By international standards the economy of South Africa is extremely energy intensive with only a few countries having higher intensities. SA's primary energy use per unit of GDP is amongst the highest in the world. The high energy and electricity intensity of the economy partly reflects SA's resource endowments (in particular the abundance of coal) but is also a function of the historical under-pricing of coal and electricity by the authorities. South African mining and industrial electricity efficiency is particularly concerning and considerably lower than the global average. This paper sets out to fill a significant gap in the South African energy literature by highlighting the importance of incorporating electricity demand factors as part of the country's energy policy and electricity planning horizon. The paper focuses its attention on modelling the electricity consumption of SA's industrial and mining sectors given these account for the lion's share of electricity demand. A differential electricity pricing policy which targets electricity intensive industrial and mining activities (as practised in China since 2004) is viewed by the author to be a superior policy to blanket electricity price increases administered by authorities in an effort to encourage electricity savings and improve energy efficiency in South Africa. - Highlights: • SA's primary energy use per unit of GDP is amongst the highest in the world. • SA industrial electricity efficiency is considerably lower than the global average. • A differential electricity pricing policy which targets electricity intensive activities. • Differential tariffs raise the cost of energy inefficiency and induces energy saving. • Highlights importance of energy demand modelling in electricity supply planning

  16. REMINDER: Saved Leave Scheme (SLS)

    CERN Multimedia

    2003-01-01

    Transfer of leave to saved leave accounts Under the provisions of the voluntary saved leave scheme (SLS), a maximum total of 10 days'* annual and compensatory leave (excluding saved leave accumulated in accordance with the provisions of Administrative Circular No 22B) can be transferred to the saved leave account at the end of the leave year (30 September). We remind you that unused leave of all those taking part in the saved leave scheme at the closure of the leave year accounts is transferred automatically to the saved leave account on that date. Therefore, staff members have no administrative steps to take. In addition, the transfer, which eliminates the risk of omitting to request leave transfers and rules out calculation errors in transfer requests, will be clearly shown in the list of leave transactions that can be consulted in EDH from October 2003 onwards. Furthermore, this automatic leave transfer optimizes staff members' chances of benefiting from a saved leave bonus provided that they ar...

  17. Opportunities of energy saving in lighting systems for public buildings

    Directory of Open Access Journals (Sweden)

    Ayman Abd El-khalek

    2017-03-01

    Full Text Available The lighting system provides many options for cost-effective energy saving with low or no inconvenience. Lighting improvements are excellent investments in most public buildings, it is usually cost-effective to address because lighting improvements are often easier to make than many process upgrades.For public buildings, the easy no and low cost options to help save money and improve the energy performance are:Understand energy use.Identify optionsPrioritize actionsMake the changes and measure the savings.Continue managing energy efficiency.The challenge is to retrofit traditional lamps with LED lamps of good quality. The benefits of LED light bulbs are long-lasting, durable, cool, mercury free, more efficient, and cost effective.The light Emitting Diode (LED bulb uses a semiconductor as its light source, and is currently one of the most energy efficient and quickly developing types of bulbs for lighting. LEDs increasingly are being purchased to replace traditional bulbs. LEDs are relatively more expensive than other types of bulbs, but are very cost-effective because they use only a fraction of electricity of traditional lighting methods nd can last for longer.Benchmarking guides decision makers to policies aimed at the energy sector through better understanding of energy consumption trends nationwide, e.g.: energy price, moderating, peak demand, and encouraging sectors, low energy expansions.The “Improving Energy Efficiency Project of Lighting and Appliances” carried out energy audits and implemented opportunities of energy saving in lighting for different type of public buildings.To rationalize the use of energy by giving guidelines to consumers, the IEEL&A project prepared some brochures.This paper leads with the results of case studies as energy audits, opportunities in lighting systems, energy saving and CO2 reduction.

  18. 31 CFR 351.47 - May I purchase definitive Series EE savings bonds through a payroll savings plan?

    Science.gov (United States)

    2010-07-01

    ... savings bonds through a payroll savings plan? 351.47 Section 351.47 Money and Finance: Treasury....47 May I purchase definitive Series EE savings bonds through a payroll savings plan? You may purchase... maintains a payroll savings plan. An authorized issuing agent must issue the bonds. ...

  19. Savings estimates for the Energy Star(registered trademark) voluntary labeling program

    International Nuclear Information System (INIS)

    Webber, Carrie A.; Brown, Richard E.; Koomey, Jonathan G.

    2000-01-01

    ENERGY STAR7 is a voluntary labeling program designed to identify and promote energy-efficient products. Operated jointly by the Environmental Protection Agency (EPA) and the U.S. Department of Energy (DOE), ENERGY STAR labels exist for more than twenty products, spanning office equipment, residential heating and cooling equipment, new homes, commercial and residential lighting, home electronics, and major appliances. We present estimates of the energy, dollar and carbon savings already achieved by the program and provide savings forecasts for several market penetration scenarios for the period 2001 to 2010. The target market penetration forecast represents our best estimate of future ENERGY STAR savings. It is based on realistic market penetration goals for each of the products. We also provide a forecast under the assumption of 100 percent market penetration; that is, we assume that all purchasers buy ENERGY STAR-compliant products instead of standard efficiency products throughout the analysis period. Finally, we assess the sensitivity of our target penetration case forecasts to greater or lesser marketing success by EPA and DOE, lower-than-expected future energy prices, and higher or lower rates of carbon emissions by electricity generators

  20. 12 CFR 561.43 - Savings association.

    Science.gov (United States)

    2010-01-01

    ..., chartered under section 5 of the Act, or a building and loan, savings and loan, or homestead association, or... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Savings association. 561.43 Section 561.43... AFFECTING ALL SAVINGS ASSOCIATIONS § 561.43 Savings association. The term savings association means a...

  1. Savings Behavior and Satisfaction with Savings: A Comparison of Low- and High-Income Groups.

    Science.gov (United States)

    Davis, Elizabeth P.; Schumm, Walter R.

    1987-01-01

    Data on 1,739 married couples from 13 states were analyzed. Associations between satisfaction with savings and level of savings with measures of motivation to save, motivations to spend, and family resources were found to differ substantially between low- and high-income couples. (Author/CH)

  2. 31 CFR 359.35 - May I purchase definitive Series I savings bonds through a payroll savings plan?

    Science.gov (United States)

    2010-07-01

    ... savings bonds through a payroll savings plan? 359.35 Section 359.35 Money and Finance: Treasury... May I purchase definitive Series I savings bonds through a payroll savings plan? You may purchase definitive bonds through deductions from your pay if your employer maintains a payroll savings plan. An...

  3. Thermal and electrical energy yield analysis of a directly water cooled photovoltaic module

    Directory of Open Access Journals (Sweden)

    Mtunzi Busiso

    2016-01-01

    Full Text Available Electrical energy of photovoltaic modules drops by 0.5% for each degree increase in temperature. Direct water cooling of photovoltaic modules was found to give improved electrical and thermal yield. A prototype was put in place to analyse the field data for a period of a year. The results showed an initial high performance ratio and electrical power output. The monthly energy saving efficiency of the directly water cooled module was found to be approximately 61%. The solar utilisation of the naturally cooled photovoltaic module was found to be 8.79% and for the directly water cooled module its solar utilisation was 47.93%. Implementation of such systems on households may reduce the load from the utility company, bring about huge savings on electricity bills and help in reducing carbon emissions.

  4. Variable cross-section windings for efficiency improvement of electric machines

    Science.gov (United States)

    Grachev, P. Yu; Bazarov, A. A.; Tabachinskiy, A. S.

    2018-02-01

    Implementation of energy-saving technologies in industry is impossible without efficiency improvement of electric machines. The article considers the ways of efficiency improvement and mass and dimensions reduction of electric machines with electronic control. Features of compact winding design for stators and armatures are described. Influence of compact winding on thermal and electrical process is given. Finite element method was used in computer simulation.

  5. Energy usage and technical potential for energy saving measures in the Swedish residential building stock

    International Nuclear Information System (INIS)

    Mata, Érika; Sasic Kalagasidis, Angela; Johnsson, Filip

    2013-01-01

    This paper provides an analysis of the current energy usage (net energy and final energy by fuels) and associated carbon dioxide (CO 2 ) emissions of the Swedish residential building stock, which includes single-family dwellings and multi-family dwellings. Twelve energy saving measures (ESMs) are assessed using a bottom–up modeling methodology, in which the Swedish residential stock is represented by a sample of 1400 buildings (based on data from the year 2005). Application of the ESMs studied gives a maximum technical reduction potential in energy demand of 53%, corresponding to a 63% reduction in CO 2 emissions. Although application of the investigated ESMs would reduce CO 2 emissions, the measures that reduce electricity consumption for lighting and appliances (LA) will increase CO 2 emissions, since the saved electricity production is less CO 2 -intensive than the fuel mix used for the increased space heating required to make up for the loss in indirect heating obtained from LA. - Highlights: ► Analysis of year 2005energy use and CO2 emissions of Swedish residential buildings. ► Includes all single-family dwellings and multi-family dwellings. ► Bottom–up modeling of building stock represented by 1400 buildings. ► Technical effects of 12 energy saving measures are assessed. ► Energy demand can be reduced by53% and associated CO 2 emissions by 63%

  6. Integration between electric heat pump and PV system to increase self-consumption of an office application

    Directory of Open Access Journals (Sweden)

    Roselli Carlo

    2017-01-01

    Full Text Available The paper examines a solar electric driven heat pump serving an office building located in southern Italy. To satisfy space heating and cooling demand a heat pump activated by electric energy available from solar photovoltaic plant is here considered. In order to improve the self-consumption of electricity available from photovoltaic system different configurations were considered introducing an electric storage and an electric vehicle. Dynamic simulations to evaluate energy performance of the system varying photovoltaic peak power (4.5–7.5 kW have been carried out. The proposed system achieves a fossil fuel primary energy saving up to about 96% in comparison to the reference conventional system based on a natural gas fired boiler, an electric chiller and the national electric grid. The results show that fossil fuel primary energy saving is higher when there are no storage battery and electric vehicle.

  7. Dual pathology proximal median nerve compression of the forearm.

    LENUS (Irish Health Repository)

    Murphy, Siun M

    2013-12-01

    We report an unusual case of synchronous pathology in the forearm- the coexistence of a large lipoma of the median nerve together with an osteochondroma of the proximal ulna, giving rise to a dual proximal median nerve compression. Proximal median nerve compression neuropathies in the forearm are uncommon compared to the prevalence of distal compression neuropathies (eg Carpal Tunnel Syndrome). Both neural fibrolipomas (Refs. 1,2) and osteochondromas of the proximal ulna (Ref. 3) in isolation are rare but well documented. Unlike that of a distal compression, a proximal compression of the median nerve will often have a definite cause. Neural fibrolipoma, also called fibrolipomatous hamartoma are rare, slow-growing, benign tumours of peripheral nerves, most often occurring in the median nerve of younger patients. To our knowledge, this is the first report of such dual pathology in the same forearm, giving rise to a severe proximal compression of the median nerve. In this case, the nerve was being pushed anteriorly by the osteochondroma, and was being compressed from within by the intraneural lipoma. This unusual case highlights the advantage of preoperative imaging as part of the workup of proximal median nerve compression.

  8. Efficient Scalable Median Filtering Using Histogram-Based Operations.

    Science.gov (United States)

    Green, Oded

    2018-05-01

    Median filtering is a smoothing technique for noise removal in images. While there are various implementations of median filtering for a single-core CPU, there are few implementations for accelerators and multi-core systems. Many parallel implementations of median filtering use a sorting algorithm for rearranging the values within a filtering window and taking the median of the sorted value. While using sorting algorithms allows for simple parallel implementations, the cost of the sorting becomes prohibitive as the filtering windows grow. This makes such algorithms, sequential and parallel alike, inefficient. In this work, we introduce the first software parallel median filtering that is non-sorting-based. The new algorithm uses efficient histogram-based operations. These reduce the computational requirements of the new algorithm while also accessing the image fewer times. We show an implementation of our algorithm for both the CPU and NVIDIA's CUDA supported graphics processing unit (GPU). The new algorithm is compared with several other leading CPU and GPU implementations. The CPU implementation has near perfect linear scaling with a speedup on a quad-core system. The GPU implementation is several orders of magnitude faster than the other GPU implementations for mid-size median filters. For small kernels, and , comparison-based approaches are preferable as fewer operations are required. Lastly, the new algorithm is open-source and can be found in the OpenCV library.

  9. Application of Superconducting Power Cables to DC Electric Railway Systems

    Science.gov (United States)

    Ohsaki, Hiroyuki; Lv, Zhen; Sekino, Masaki; Tomita, Masaru

    For novel design and efficient operation of next-generation DC electric railway systems, especially for their substantial energy saving, we have studied the feasibility of applying superconducting power cables to them. In this paper it is assumed that a superconducting power cable is applied to connect substations supplying electric power to trains. An analysis model line was described by an electric circuit, which was analyzed with MATLAB-Simulink. From the calculated voltages and currents of the circuit, the regenerative brake and the energy losses were estimated. In addition, assuming the heat loads of superconducting power cables and the cryogenic efficiency, the energy saving of the total system was evaluated. The results show that the introduction of superconducting power cables could achieve the improved use of regenerative brake, the loss reduction, the decreased number of substations, the reduced maintenance, etc.

  10. Risk transfer via energy-savings insurance

    International Nuclear Information System (INIS)

    Mills, Evan

    2003-01-01

    Among the key barriers to investment in energy efficiency are uncertainties about attaining projected energy savings and potential disputes over stipulated savings. The fields of energy management and risk management are thus intertwined. While many technical methods have emerged to manage performance risks (e.g. building diagnostics and commissioning), financial methods are less developed in the energy management arena than in other segments of the economy. Energy-savings insurance (ESI) - formal insurance of predicted energy savings - transfers and spreads both types of risk over a larger pool of energy efficiency projects and reduces barriers to market entry of smaller energy service firms who lack sufficiently strong balance sheets to self-insure the savings. ESI encourages those implementing energy-saving projects to go beyond standard measures and thereby achieve more significant levels of energy savings. Insurance providers are proponents of improved savings measurement and verification techniques, as well as maintenance, thereby contributing to national energy-saving objectives. If properly applied, ESI can potentially reduce the net cost of energy-saving projects by reducing the interest rates charged by lenders, and by increasing the level of savings through quality control. Governmental agencies have been pioneers in the use of ESI and could continue to play a role

  11. 12 CFR 575.10 - Acquisition and disposition of savings associations, savings and loan holding companies, and...

    Science.gov (United States)

    2010-01-01

    ... associations, savings and loan holding companies, and other corporations by mutual holding companies. 575.10... COMPANIES § 575.10 Acquisition and disposition of savings associations, savings and loan holding companies... savings and loan holding company in the stock form that is not a subsidiary holding company, provided the...

  12. Can rural electric cooperatives survive in a restructured US electric market? An empirical analysis

    International Nuclear Information System (INIS)

    Greer, Monica Lynne

    2003-01-01

    This paper examines the ability of rural electric distribution cooperatives to continue operating in their present form in a restructured electricity market. More specifically, I develop and estimate a quadratic cost model, which, unlike many of the cost functions employed in studies of this nature, conforms to all of the properties of a proper cost function. Using 1996 data, I find that these firms are not operating in a cost-minimizing fashion. This finding seems to occur because each is too small in terms of the quantity of electricity distributed. As a result, mergers between these firms could yield substantial savings and help ensure their survival in their present form in a deregulated market

  13. A Comprehensive Analysis for Widespread use of Electric Vehicles

    OpenAIRE

    Yu Zhou; Zhaoyang Dong; Xiaomei Zhao

    2011-01-01

    This paper mainly investigates the environmental and economic impacts of worldwide use of electric vehicles. It can be concluded that governments have good reason to promote the use of electric vehicles. First, the global vehicles population is evaluated with the help of grey forecasting model and the amount of oil saving is estimated through approximate calculation. After that, based on the game theory, the amount and types of electricity generation needed by electronic ...

  14. Solar island electricity supply at Flanitzhuette. Solare Inselstromversorgung Flanitzhuette

    Energy Technology Data Exchange (ETDEWEB)

    Kranz, U. (Bayernwerk AG, Muenchen (Germany))

    1993-01-01

    The aim of this research project is the planning, erection and operation of a permanent electricity supply independent of the grid based on photo-electrics for an isolated hamlet in the Bavarian Forest. Criteria for the development and optimisation of solar electricity supply concepts are to be obtained from practical experience. The investigation and exploitation of energ saving potential and an harmonious integration of the solar plant in the landscape are also important aspects. (orig.)

  15. Assessing the value of pulp mill biomass savings in a climate change conscious economy

    International Nuclear Information System (INIS)

    Adahl, Anders; Harvey, Simon; Berntsson, Thore

    2006-01-01

    Pulp mills use significant amounts of biofuels, both internal and purchased. Biofuels could contribute to reach greenhouse gas emission targets at competitive costs. Implementing process integration measures at a pulp mill in order to achieve pulp production with less use of energy (biofuels) has not only on-site consequences but also off-site consequences, such as substitution of fossil fuels elsewhere by the saved pulp mill biofuels, and less on-site electric power generation. In this paper a method, a linking model, is suggested to analyse pulp mill biofuel saving measures when carbon dioxide (CO 2 ) external costs are internalised. The linking model is based on equilibrium economics and links information from CO 2 constrained energy market future scenarios with process integration measures. Pulp mill economics and marginal energy market CO 2 response are identified. In an applied study, four process integration measures at a Swedish pulp mill were analysed using five energy market future scenarios emanating from a Nordic energy model. The investigated investment alternatives for biofuel savings all result in positive net annual savings, irrespectively of the scenario used. However, CO 2 emissions may increase or decrease depending on the future development of the Nordic energy market

  16. Portfolio optimization using median-variance approach

    Science.gov (United States)

    Wan Mohd, Wan Rosanisah; Mohamad, Daud; Mohamed, Zulkifli

    2013-04-01

    Optimization models have been applied in many decision-making problems particularly in portfolio selection. Since the introduction of Markowitz's theory of portfolio selection, various approaches based on mathematical programming have been introduced such as mean-variance, mean-absolute deviation, mean-variance-skewness and conditional value-at-risk (CVaR) mainly to maximize return and minimize risk. However most of the approaches assume that the distribution of data is normal and this is not generally true. As an alternative, in this paper, we employ the median-variance approach to improve the portfolio optimization. This approach has successfully catered both types of normal and non-normal distribution of data. With this actual representation, we analyze and compare the rate of return and risk between the mean-variance and the median-variance based portfolio which consist of 30 stocks from Bursa Malaysia. The results in this study show that the median-variance approach is capable to produce a lower risk for each return earning as compared to the mean-variance approach.

  17. Seamless electricity trade between Canada and US Northeast

    International Nuclear Information System (INIS)

    Bernard, J.-T.; Clavet, Frederic; Ondo, J.-C.

    2005-01-01

    We analyze how the wholesale electricity market deregulation could modify exchanges between three Canadian regions (Ontario, Quebec and New Brunswick) and two US regions (New York and New England), on the base of their loads and available resources when the regulatory change took place in 1997. We find that the pre-1997 exchanges already made possible fuel cost savings of $397.2 million per year while deregulation adds annual savings of $358.7 million. Canadian regions are the main beneficiaries under the assumption that exports are priced at the marginal costs of the importing regions. Imports from the Canadian regions, although significant, are not large enough to lower the marginal costs of the US regions. Hence electricity deregulation across the border should not significantly decrease prices in the US regions although the latter are becoming more dependent upon imports from Canada. Greenhouse gas emissions increase by 4.3 Mt CO 2 eq. in the wake of the open wholesale electricity market because of the low cost of coal, particularly in Ontario. Environmental concerns and the limited availability of additional hydroelectric power in Canada could change the trade patterns as electricity demand continue to grow

  18. RTE - Electricity transport network operator. Energy is our future: let's save it

    International Nuclear Information System (INIS)

    2014-01-01

    Managing and developing the French electricity transport network is essential to provide quality electricity on a continuous basis to all consumers. Since it was founded in 2000, and since it was made into a public service company (2005), RTE has proven its ability to fulfil its public interest mission in complete security. In an open European electricity market, RTE is recognised for offering all of its customers fair access to its network, which is the first condition for healthy competition. Based on this and thanks to its investments and operating quality, RTE is constantly improving its performances to meet its customers', public authorities' and the Energy Regulation Committee's requirements. This public service action is focused on four strategic priorities: performance of industrial facilities; a human and managerial policy focused on skills and efficiency; sustainable development; professionalism and innovation. This brochure presents RTE's missions, company overview and European cooperation

  19. Saving energy in the baking industry. Energiesparen in der Baeckerei

    Energy Technology Data Exchange (ETDEWEB)

    1992-04-01

    Measures for energy conservation and rational energy use have been given priority in almost all sectors of our economy. Between July and December 1991, 40 bakeries were studied for their energy consumptions in a study commissioned by BEWAG/EBAG in Berlin. Most bakeries will have to reckon with annual turnovers which will not rise as they used to. This brochure explains those measures which are best suited to use electric power in the business effectively to save energy, to lower costs and to reduce pollution. (orig./UA)

  20. Energy Impacts of Wide Band Gap Semiconductors in U.S. Light-Duty Electric Vehicle Fleet.

    Science.gov (United States)

    Warren, Joshua A; Riddle, Matthew E; Graziano, Diane J; Das, Sujit; Upadhyayula, Venkata K K; Masanet, Eric; Cresko, Joe

    2015-09-01

    Silicon carbide and gallium nitride, two leading wide band gap semiconductors with significant potential in electric vehicle power electronics, are examined from a life cycle energy perspective and compared with incumbent silicon in U.S. light-duty electric vehicle fleet. Cradle-to-gate, silicon carbide is estimated to require more than twice the energy as silicon. However, the magnitude of vehicle use phase fuel savings potential is comparatively several orders of magnitude higher than the marginal increase in cradle-to-gate energy. Gallium nitride cradle-to-gate energy requirements are estimated to be similar to silicon, with use phase savings potential similar to or exceeding that of silicon carbide. Potential energy reductions in the United States vehicle fleet are examined through several scenarios that consider the market adoption potential of electric vehicles themselves, as well as the market adoption potential of wide band gap semiconductors in electric vehicles. For the 2015-2050 time frame, cumulative energy savings associated with the deployment of wide band gap semiconductors are estimated to range from 2-20 billion GJ depending on market adoption dynamics.

  1. Report on energy saving vision in Santo-cho region; Santocho chiiki sho energy vision hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    An energy-saving vision was decided on in Santo-cho region in Hyogo Prefecture, with its outline reported. This town is such that about 80% of the region is mountains, forests and wilderness and that aging is advancing at the rate above that of Hyogo Prefecture or the national average. Nearly entire energy of the town is dependent on the supply from outside. The energy consumption is somewhat increasing as a whole, with that of the people's livelihood/domestic sector and of transportation sector are rising. In the classification of fuels, electricity is growing in consumption. As an energy-saving vision, it aimed principally at personal surroundings in which every one got into the habit of saving energy continuously without being forced. The basic plan for the energy conservation drive consisted of inducement to an energy-saving life style, energy conservation to be spread by the next generation children, continuation of energy saving activity rooted in the region, and promotion of energy conservation as a basis for introducing new energy. The diffusion and enlightenment for children destined to lead the next generation were defined as a particularly important assignment, as was the promotion of energy conservation and environmental education. (NEDO)

  2. The satisfaction of developing a project of electrical energy saving; La satisfaccion de desarrollar un proyecto de ahorro de energia electrica

    Energy Technology Data Exchange (ETDEWEB)

    Arreola Suarez, Alejandro [Hotel Club Marival, Nuevo Vallarta, Nayarit (Mexico)

    2002-09-01

    The projects for the energy saving in hotels represent a great opportunity to reduce the operation costs in the demand and consumption of electrical energy, since the existing facilities can take advantage of new technologies in illumination, air conditioning, refrigeration and heating. By their constitution, the hotels work the year around uninterruptedly and must provide all type of services to the guests and working personnel, which originates that they consume great amounts of energy in air conditioning, lightning, laundry, etc., since the prestige of the installation depends on it. [Spanish] Los proyectos para el ahorro de energia en hoteles representan una gran oportunidad para reducir costos de operacion en la demanda y consumo de energia electrica, ya que las instalaciones existentes pueden aprovechar nuevas tecnologias en iluminacion, aire acondicionado, refrigeracion y calefaccion. Por su constitucion, los hoteles trabajan ininterrumpidamente todo el ano y deben proporcionar toda clase de servicios a los huespedes y personal que labora, lo cual origina que consuman grandes cantidades de energia en aire acondicionado, iluminacion, lavanderia, etc., pues de ello depende el prestigio de la instalacion.

  3. Electrical Generation for More-Electric Aircraft Using Solid Oxide Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Whyatt, Greg A.; Chick, Lawrence A.

    2012-04-01

    This report examines the potential for Solid-Oxide Fuel Cells (SOFC) to provide electrical generation on-board commercial aircraft. Unlike a turbine-based auxiliary power unit (APU) a solid oxide fuel cell power unit (SOFCPU) would be more efficient than using the main engine generators to generate electricity and would operate continuously during flight. The focus of this study is on more-electric aircraft which minimize bleed air extraction from the engines and instead use electrical power obtained from generators driven by the main engines to satisfy all major loads. The increased electrical generation increases the potential fuel savings obtainable through more efficient electrical generation using a SOFCPU. However, the weight added to the aircraft by the SOFCPU impacts the main engine fuel consumption which reduces the potential fuel savings. To investigate these relationships the Boeing 787­8 was used as a case study. The potential performance of the SOFCPU was determined by coupling flowsheet modeling using ChemCAD software with a stack performance algorithm. For a given stack operating condition (cell voltage, anode utilization, stack pressure, target cell exit temperature), ChemCAD software was used to determine the cathode air rate to provide stack thermal balance, the heat exchanger duties, the gross power output for a given fuel rate, the parasitic power for the anode recycle blower and net power obtained from (or required by) the compressor/expander. The SOFC is based on the Gen4 Delphi planar SOFC with assumed modifications to tailor it to this application. The size of the stack needed to satisfy the specified condition was assessed using an empirically-based algorithm. The algorithm predicts stack power density based on the pressure, inlet temperature, cell voltage and anode and cathode inlet flows and compositions. The algorithm was developed by enhancing a model for a well-established material set operating at atmospheric pressure to reflect the

  4. DEVELOPING CONVENIENT MOTOR SELECTION ALGORITHM ACCORDING TO ROAD CONDITIONS IN ELECTRIC VEHICLES

    OpenAIRE

    BAŞER, EKREM; ALTUN, YUSUF

    2016-01-01

    Nowadays, automotive industry is tending to electric vehicles due to reduction of fuel reserves in order to save energy, reduce air pollution and carbon emission. With the impact of technological advencements on battery and power electronics, the studies on electric vehicles have been gradually increased and many of automobile manifacturers have produced new electric vehicles. Different type of electric motors has been tried on electric vehicles until today. This motors have difference feautu...

  5. [Research on carbon reduction potential of electric vehicles for low-carbon transportation and its influencing factors].

    Science.gov (United States)

    Shi, Xiao-Qing; Li, Xiao-Nuo; Yang, Jian-Xin

    2013-01-01

    Transportation is the key industry of urban energy consumption and carbon emissions. The transformation of conventional gasoline vehicles to new energy vehicles is an important initiative to realize the goal of developing low-carbon city through energy saving and emissions reduction, while electric vehicles (EV) will play an important role in this transition due to their advantage in energy saving and lower carbon emissions. After reviewing the existing researches on energy saving and emissions reduction of electric vehicles, this paper analyzed the factors affecting carbon emissions reduction. Combining with electric vehicles promotion program in Beijing, the paper analyzed carbon emissions and reduction potential of electric vehicles in six scenarios using the optimized energy consumption related carbon emissions model from the perspective of fuel life cycle. The scenarios included power energy structure, fuel type (energy consumption per 100 km), car type (CO2 emission factor of fuel), urban traffic conditions (speed), coal-power technologies and battery type (weight, energy efficiency). The results showed that the optimized model was able to estimate carbon emissions caused by fuel consumption more reasonably; electric vehicles had an obvious restrictive carbon reduction potential with the fluctuation of 57%-81.2% in the analysis of six influencing factors, while power energy structure and coal-power technologies play decisive roles in life-cycle carbon emissions of electric vehicles with the reduction potential of 78.1% and 81.2%, respectively. Finally, some optimized measures were proposed to reduce transport energy consumption and carbon emissions during electric vehicles promotion including improving energy structure and coal technology, popularizing energy saving technologies and electric vehicles, accelerating the battery R&D and so on. The research provides scientific basis and methods for the policy development for the transition of new energy vehicles

  6. Papillary carcinoma in median aberrant thyroid (ectopic) - case report.

    Science.gov (United States)

    Hebbar K, Ashwin; K, Shashidhar; Deshmane, Vijaya Laxmi; Kumar, Veerendra; Arjunan, Ravi

    2014-06-01

    Median ectopic thyroid may be encountered anywhere from the foramen caecum to the diaphragm. Non lingual median aberrant thyroid (incomplete descent) usually found in the infrahyoid region and malignant transformation in this ectopic thyroid tissue is very rare. We report an extremely rare case of papillary carcinoma in non lingual median aberrant thyroid in a 25-year-old female. The differentiation between a carcinoma arising in the median ectopic thyroid tissue and a metastatic papillary carcinoma from an occult primary in the main thyroid gland is also discussed.

  7. Entrepreneurial Saving Practices and Reinvestment

    NARCIS (Netherlands)

    Beck, Thorsten; Pamuk, Haki; Uras, Burak R.

    2017-01-01

    We use a novel enterprise survey to gauge the relationship between saving instruments and entrepreneurial reinvestment. We show that while most informal saving practices are not associated with a lower likelihood of reinvestment when compared with formal saving practices, there is a significantly

  8. A statistical analysis of the energy policy act of 2005, its changes to the daylight saving program, and impact on residential energy consumption

    Science.gov (United States)

    Murray, Patrick L.

    Government programs designed to decrease resource consumption, improve productivity and capitalize on extended daylight hours in the summer have been developed and implemented throughout the world for nearly three hundred years. In 2005, The United States government adopted an extended daylight savings program that increases the number of weeks where the country observes Daylight Saving Time (DST) from 31 to 35 weeks. The program took effect in March 2007. Arguments in support of DST programs highlight the portion of electricity consumption attributed to residential lighting in the evening hours. Adjusting clocks forward by one hour in summer months is believed to reduce electricity consumption due to lighting and therefore significantly reduce residential energy consumption during the period of DST. This paper evaluates the efficacy of the changes to DST resulting from the Energy Policy Act of 2005. The study focuses on changes to household electricity consumption during the extended four weeks of DST. Arizona, one of two states that continue to opt out of DST serves as the study's control for a comparison with neighboring states, Colorado, Nebraska, Nevada, New Mexico, Oklahoma, Texas and Utah. Results from the regression analysis of a Difference in Difference model indicate that contrary to evaluations by Congress and the Department of Energy, the four week period of Extended Daylight Saving Time does not produce a significant decrease in per capita electricity consumption in Southwestern states.

  9. Risk transfer via energy savings insurance

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Evan

    2001-10-01

    Among the key barriers to investment in energy efficiency improvements are uncertainties about attaining projected energy savings and apprehension about potential disputes over these savings. The fields of energy management and risk management are thus intertwined. While many technical methods have emerged to manage performance risks (e.g. building commissioning), financial risk transfer techniques are less developed in the energy management arena than in other more mature segments of the economy. Energy Savings Insurance (ESI) - formal insurance of predicted energy savings - is one method of transferring financial risks away from the facility owner or energy services contractor. ESI offers a number of significant advantages over other forms of financial risk transfer, e.g. savings guarantees or performance bonds. ESI providers manage risk via pre-construction design review as well as post-construction commissioning and measurement and verification of savings. We found that the two mos t common criticisms of ESI - excessive pricing and onerous exclusions - are not born out in practice. In fact, if properly applied, ESI can potentially reduce the net cost of energy savings projects by reducing the interest rates charged by lenders, and by increasing the level of savings through quality control. Debt service can also be ensured by matching loan payments to projected energy savings while designing the insurance mechanism so that payments are made by the insurer in the event of a savings shortfall. We estimate the U.S. ESI market potential of $875 million/year in premium income. From an energy-policy perspective, ESI offers a number of potential benefits: ESI transfers performance risk from the balance sheet of the entity implementing the energy savings project, thereby freeing up capital otherwise needed to ''self-insure'' the savings. ESI reduces barriers to market entry of smaller energy services firms who do not have sufficiently strong balance

  10. Investigation of Electrical Energy Efficiency Use in an Automobile Assembly Industry

    Directory of Open Access Journals (Sweden)

    Jacob TSADO

    2016-12-01

    Full Text Available This research work investigated the electrical energy efficiency improvement and cost saving potentials for automobile assembly plant; a case of Peugeot Automobile Nigeria Limited. The study identified lighting system as a major source through which energy is being wasted, hence efficient energy saving lighting systems are being proffered; also saving accrued were determined to justify their deployment. In the course of this work, an energy saving calculating tool was developed to calculate energy saving capabilities using energy efficient lamps. With ample devotion to the implementation of the recommendations made, the cost of energy per car will be drastically reduced while profits are also made simultaneously. In all, more cars will be produced thus translating to more employment opportunities in the industry.

  11. Robust median estimator in logisitc regression

    Czech Academy of Sciences Publication Activity Database

    Hobza, T.; Pardo, L.; Vajda, Igor

    2008-01-01

    Roč. 138, č. 12 (2008), s. 3822-3840 ISSN 0378-3758 R&D Projects: GA MŠk 1M0572 Grant - others:Instituto Nacional de Estadistica (ES) MPO FI - IM3/136; GA MŠk(CZ) MTM 2006-06872 Institutional research plan: CEZ:AV0Z10750506 Keywords : Logistic regression * Median * Robustness * Consistency and asymptotic normality * Morgenthaler * Bianco and Yohai * Croux and Hasellbroeck Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 0.679, year: 2008 http://library.utia.cas.cz/separaty/2008/SI/vajda-robust%20median%20estimator%20in%20logistic%20regression.pdf

  12. Dual pathology proximal median nerve compression of the forearm.

    Science.gov (United States)

    Murphy, Siun M; Browne, Katherine; Tuite, David J; O'Shaughnessy, Michael

    2013-12-01

    We report an unusual case of synchronous pathology in the forearm- the coexistence of a large lipoma of the median nerve together with an osteochondroma of the proximal ulna, giving rise to a dual proximal median nerve compression. Proximal median nerve compression neuropathies in the forearm are uncommon compared to the prevalence of distal compression neuropathies (eg Carpal Tunnel Syndrome). Both neural fibrolipomas (Refs. 1,2) and osteochondromas of the proximal ulna (Ref. 3) in isolation are rare but well documented. Unlike that of a distal compression, a proximal compression of the median nerve will often have a definite cause. Neural fibrolipoma, also called fibrolipomatous hamartoma are rare, slow-growing, benign tumours of peripheral nerves, most often occurring in the median nerve of younger patients. To our knowledge, this is the first report of such dual pathology in the same forearm, giving rise to a severe proximal compression of the median nerve. In this case, the nerve was being pushed anteriorly by the osteochondroma, and was being compressed from within by the intraneural lipoma. This unusual case highlights the advantage of preoperative imaging as part of the workup of proximal median nerve compression. Copyright © 2013 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

  13. Towards a low carbon electric system in Mexico

    International Nuclear Information System (INIS)

    Islas-Samperio, Jorge; Grande-Acosta, Genice K.

    2015-10-01

    The authors first propose an overview of the shares of the different energy sources, and notably renewable sources, in the Mexican electricity production. It appears that fossil fuels prevail despite the fact Mexico possesses an extremely high potential in renewable energies. They comment future trends: increase of electricity demand in the different sectors, a scenario mainly based on gas and coal, a share which remain low for renewable energies despite their production increase. They also comment the content of a transition scenario which aims at energy savings in the different sectors (housing, commercial buildings, public services, transports, industry, oil industry). Various measures (replacement or improvement of equipment) and their saving are indicated. The impact of this scenario is discussed, notably in terms of reduction of greenhouse gas emissions

  14. Run-Curve Design for Energy Saving Operation in a Modern DC-Electrification

    Science.gov (United States)

    Koseki, Takafumi; Noda, Takashi

    Mechanical brakes are often used by electric trains. These brakes have a few problems like response speed, coefficient of friction, maintenance cost and so on. As a result, methods for actively using regenerative brakes are required. In this paper, we propose the useful pure electric braking, which would involve ordinary brakes by only regenerative brakes without any mechanical brakes at high speed. Benefits of our proposal include a DC-electrification system with regenerative substations that can return powers to the commercial power system and a train that can use the full regenerative braking force. We furthermore evaluate the effects on running time and energies saved by regenerative substations in the proposed method.

  15. Electrical engineering a pocket reference

    CERN Document Server

    Schmidt-Walter, Heinz

    2007-01-01

    This essential reference offers you a well-organized resource for accessing the basic electrical engineering knowledge you need for your work. Whether you're an experienced engineer who appreciates an occasional refresher in key areas, or a student preparing to enter the field, Electrical Engineering: A Pocket Reference provides quick and easy access to fundamental principles and their applications. You also find an extensive collection of time-saving equations that help simplify your daily projects.Supported with more than 500 diagrams and figures, 60 tables, and an extensive index, this uniq

  16. Median nail dystrophy involving the thumb nail

    Directory of Open Access Journals (Sweden)

    Rahulkrishna Kota

    2016-01-01

    Full Text Available Median canaliform dystrophy of Heller is a rare entity characterized by a midline or a paramedian ridge or split and canal formation in nail plate of one or both the thumb nails. It is an acquired condition resulting from a temporary defect in the matrix that interferes with nail formation. Habitual picking of the nail base may be responsible for some cases. Histopathology classically shows parakeratosis, accumulation of melanin within and between the nail bed keratinocytes. Treatment of median nail dystrophy includes injectable triamcinalone acetonide, topical 0.1% tacrolimus, and tazarotene 0.05%, which is many a times challenging for a dermatologist. Psychiatric opinion should be taken when associated with the depressive, obsessive-compulsive, or impulse-control disorder. We report a case of 19-year-old male diagnosed as median nail dystrophy.

  17. Large window median filtering on Clip7

    Energy Technology Data Exchange (ETDEWEB)

    Mathews, K N

    1983-07-01

    Median filtering has been found to be a useful operation to perform on images in order to reduce random noise while preserving edges of objects. However, in some cases, as the resolution of the image increases, so too does the required window size of the filter. For parallel array processors, this leads to problems when dealing with the large amount of data involved. That is to say that there tend to be problems over slow access of data from pixels over a large neighbourhood, lack of available storage of this data during the operation and long computational times for finding the median. An algorithm for finding the median, designed for use on byte wide architecture parallel array processors is presented together with its implementation on Clip7, a scanning array of such processors. 6 references.

  18. Biopulping: A new energy-saving technology for papermaking

    International Nuclear Information System (INIS)

    Scott, G.M.; Akhtar, M.; Lentz, M.J.; Kirk, T.K.; Swaney, R.; Shipley, D.F.

    1997-01-01

    Biopulping is defined as the treatment of wood chips with lignin-degrading fungi prior to pulping. Fungal pretreatment prior to mechanical pulping reduces electrical energy requirements during refining or increases mill throughput, improves paper strength, reduces the pitch content, reduces cooking time for sulfite pulping, and reduces the environmental impact of pulping. The recent work involved scaling up the biopulping process towards the industrial level, investigating both the engineering and economic feasibility of the technology. The authors envision the process to be done in either a chip-pile or silo-based system for which several factors need to be considered. These factors include the degree of decontamination, a hospitable environment for the fungus, and the overall process economics. Currently, treatment of the chips with low pressure steam is sufficient for decontamination. Furthermore, a simple, forced ventilation system can be used to maintain the proper temperature, humidity, and moisture content throughout the chip bed, thus promoting uniform growth of the fungus. The pilot-scale trial resulted in the successful treatment of 4 tons, of wood chips (dry weight basis) with results comparable to those on a laboratory scale. For mechanical pulping, a 2-week treatment results in approximately 30% energy savings that, considering the additional equipment and operating costs, results in an overall savings of $9 to $20/ton of pulp in a chip-pile system. The other benefits that biopulping confers improve the economics considerably A larger, 40-ton trial was also successful, with energy savings and paper properties comparable with the laboratory scale

  19. Cogeneration plant in a pasta factory: Energy saving and environmental benefit

    International Nuclear Information System (INIS)

    Panno, Domenico; Messineo, Antonio; Dispenza, Antonella

    2007-01-01

    Italy produces approximately 4,520,000 tons of pasta annually, which is about 67% of its total productive potential. As factories need electric and thermal energy simultaneously, combined heat and power (CHP) systems are the most suitable. This paper describes a feasibility study of a CHP plant in a pasta factory in Italy while analyzing energy saving and environmental benefits. Commercially available CHP systems suitable for the power range of energy demand in pasta production use reciprocating engines or gas turbines. This study demonstrates how their use can reduce both energy costs and CO 2 equivalent greenhouse gas emission in the environment. An economic analysis was performed following the methodology set out by Italian National Agency for Technology, Energy and Environment (ENEA) based on a discounted cash flow (DCF) method called 'Valore Attuale Netto' (VAN), which uses a cash flow based on the saving of energy when using different energy processes

  20. Development with Sustainable Use of Electricity

    DEFF Research Database (Denmark)

    The book consist of 14 contributions from 9 different countries, presented at an international workshop in 1996 in Lopuzna, Poland. Some chapters discuss the more general aspects of this rather new field of research about how using the electricity with greater care can save a substantial part...... of the present consumption. It also includes chapters on Integrated Resource Planning and Least Cost Planning. Other chapters give concrete and striking examples of how much has been achieved within lighting, communication, motors, etc. as well as whole houses. Finally some chapters describe the policies of some...... countries and EU, aiming at harvesting the immense savings....

  1. The influence of multiple goals on driving behavior: the case of safety, time saving, and fuel saving.

    Science.gov (United States)

    Dogan, Ebru; Steg, Linda; Delhomme, Patricia

    2011-09-01

    Due to the innate complexity of the task drivers have to manage multiple goals while driving and the importance of certain goals may vary over time leading to priority being given to different goals depending on the circumstances. This study aimed to investigate drivers' behavioral regulation while managing multiple goals during driving. To do so participants drove on urban and rural roads in a driving simulator while trying to manage fuel saving and time saving goals, besides the safety goals that are always present during driving. A between-subjects design was used with one group of drivers managing two goals (safety and fuel saving) and another group managing three goals (safety, fuel saving, and time saving) while driving. Participants were provided continuous feedback on the fuel saving goal via a meter on the dashboard. The results indicate that even when a fuel saving or time saving goal is salient, safety goals are still given highest priority when interactions with other road users take place and when interacting with a traffic light. Additionally, performance on the fuel saving goal diminished for the group that had to manage fuel saving and time saving together. The theoretical implications for a goal hierarchy in driving tasks and practical implications for eco-driving are discussed. Copyright © 2011 Elsevier Ltd. All rights reserved.

  2. Effects of feedback on residential electricity demand—Findings from a field trial in Austria

    International Nuclear Information System (INIS)

    Schleich, Joachim; Klobasa, Marian; Gölz, Sebastian; Brunner, Marc

    2013-01-01

    This paper analyzes the effects of providing feedback on electricity consumption in a field trial involving more than 1500 households in Linz, Austria. About half of these households received feedback together with information about electricity-saving measures (pilot group), while the remaining households served as a control group. Participation in the pilot group was random, but households were able to choose between two types of feedback: access to a web portal or written feedback by post. Results from cross section OLS regression suggest that feedback provided to the pilot group corresponds with electricity savings of around 4.5% for the average household. Our results from quantile regressions imply that for households in the 30th to the 70th percentile of electricity consumption, feedback on electricity consumption is statistically significant and effects are highest in absolute terms and as a share of electricity consumption. For percentiles below or above this range, feedback appears to have no effect. Finally, controlling for a potential endogeneity bias induced by non random participation in the feedback type groups, we find no difference in the effects of feedback provided via the web portal and by post. - Highlights: • We estimate the effects of feedback on household electricity use in a field trial in Linz, Austria. • Providing feedback on electricity use corresponds with average savings of around 4.5%. • Effects of feedback are most pronounced in the 30th to the 70th percentile. • Feedback provided via a web portal and by post appears equally effective

  3. Energy saving in energy market reform—The feed-in tariffs option

    International Nuclear Information System (INIS)

    Eyre, Nick

    2013-01-01

    The use of feed-in tariffs (FITs) is now widespread for renewable energy and under discussion for other low carbon electricity generation, but not for energy efficiency. There is a small literature on FITs for electricity demand reduction, but not energy efficiency more generally. This paper considers the general application of FITs on the demand side and sets out the economic arguments in the context of changing energy markets. It then discusses the implications of some practical issues, including the definitional problems arising from the difference between energy efficiency and demand reduction. Using experience from historical energy efficiency programmes, it considers the public benefits, payment methods and policy scope that need to be considered and how these might affect policy design. It makes some provisional estimates of economically justified payments in the context of the proposed UK energy market reform. It concludes that FITs for energy saving might be a powerful tool for incentivising energy efficiency. - Highlights: ► The concept of an energy saving feed-in tariff (ESFIT) is introduced and analysed. ► ESFITs are potentially an alternative to supplier energy efficiency obligations. ► To maximise effectiveness, ESFITs should be paid as capital grants. ► ESFITs are justifiable if there are premium prices for low carbon generation. ► Higher rates of ESFIT may be justified to overcome barriers to energy efficiency.

  4. The energy efficiency challenge: Save the baby throw out the bathwater

    Energy Technology Data Exchange (ETDEWEB)

    Chamberlin, J.H.; Herman, P.

    1995-12-01

    In the more competitive, restructured industry that is emerging, electricity providers will need to build on what has been learned about DSM in the past 15 years, focusing on providing information and technical services, reducing customer risk through guarantees, and solving customer financing problems. Efficiency solutions that make sense for each customer may be the only ones that get used. Over the last 15 years, electric utilities have spent billions of dollars on demand-side management activities. The Energy Information Administration reports that utilites spent $2.8 billion on DSM in 1993 alone. Through these programs, utilites claim to have saved 40,000 MW of demand and 44,000 GWh of energy, and millions of participating customers have saved billions of dollars. But the development and implementation of these programs have not been without controversy. For the past 15 years, DSM`s advocates and critics have debated the most fundamental aspects of the selection and evaluation of DSM activities. Although protagonists have argued their views within the context of monopoly regulation, it has become apparent in recent years that the basic structure of the industry is undergoing fundamental change. Today, the debate regarding the role of DSM and, more gnerally, the provision of efficiency services to utility customers continues. Here the authors seek to summarize the important lessons learned and to suggest the changes that these lessons imply for DSM activities.

  5. Scenario analysis of energy saving and CO_2 emissions reduction potentials to ratchet up Japanese mitigation target in 2030 in the residential sector

    International Nuclear Information System (INIS)

    Wakiyama, Takako; Kuramochi, Takeshi

    2017-01-01

    This paper assesses to what extent CO_2 emissions from electricity in the residential sector can be further reduced in Japan beyond its post-2020 mitigation target (known as “Intended Nationally Determined Contribution (INDC)”). The paper examines the reduction potential of electricity demand and CO_2 emissions in the residential sector by conducting a scenario analysis. Electricity consumption scenarios are set up using a time-series regression model, and used to forecast the electricity consumption patterns to 2030. The scenario analysis also includes scenarios that reduce electricity consumption through enhanced energy efficiency and energy saving measures. The obtained results show that Japan can reduce electricity consumption and CO_2 emissions in the residential sector in 2030 more than the Japanese post-2020 mitigation target indicates. At the maximum, the electricity consumption could be reduced by 35 TWh, which contributes to 55.4 MtCO_2 of emissions reduction in 2030 compared to 2013 if the voluntarily targeted CO_2 intensity of electricity is achieved. The result implies that Japan has the potential to ratchet up post-2020 mitigation targets discussed under the Paris Agreement of the United Nations Framework Convention on Climate Change (UNFCCC). - Highlights: • Further reduction of electricity consumption is possible beyond Japan's post-2020 mitigation target. • Energy saving efforts by households and incentives to reduce electricity demands are required. • Improvement of CO_2 intensity from electricity is a key factor in the reduction of CO_2 emissions.

  6. Saving-enhanced memory: the benefits of saving on the learning and remembering of new information.

    Science.gov (United States)

    Storm, Benjamin C; Stone, Sean M

    2015-02-01

    With the continued integration of technology into people's lives, saving digital information has become an everyday facet of human behavior. In the present research, we examined the consequences of saving certain information on the ability to learn and remember other information. Results from three experiments showed that saving one file before studying a new file significantly improved memory for the contents of the new file. Notably, this effect was not observed when the saving process was deemed unreliable or when the contents of the to-be-saved file were not substantial enough to interfere with memory for the new file. These results suggest that saving provides a means to strategically off-load memory onto the environment in order to reduce the extent to which currently unneeded to-be-remembered information interferes with the learning and remembering of other information. © The Author(s) 2014.

  7. Demand Response Application forReliability Enhancement in Electricity Market

    OpenAIRE

    Romera Pérez, Javier

    2015-01-01

    The term reliability is related with the adequacy and security during operation of theelectric power system, supplying the electricity demand over time and saving thepossible contingencies because every inhabitant needs to be supplied with electricity intheir day to day. Operating the system in this way entails spending money. The first partof the project is going to be an analysis of the reliability and the economic impact of it.During the last decade, electric utilities and companies had be...

  8. Switching from originator brand medicines to generic equivalents in selected developing countries: how much could be saved?

    Science.gov (United States)

    Cameron, Alexandra; Mantel-Teeuwisse, Aukje K; Leufkens, Hubert G M; Laing, Richard Ogilvie

    2012-01-01

    In low- and middle-income countries, patients and reimbursement agencies that purchase medicines in the private sector pay more for originator brands when generic equivalents exist. We estimated the savings that could be obtained from a hypothetical switch in medicine consumption from originator brands to lowest-priced generic equivalents for a selection of medicines in 17 countries. In this cost minimization analysis, the prices of originator brands and their lowest-priced generic equivalents were obtained from facility-based surveys conducted by using a standard methodology. Fourteen medicines most commonly included in the surveys, plus three statins, were included in the analysis. For each medicine, the volume of private sector consumption of the originator brand product was obtained from IMS Health, Inc. Volumes were applied to the median unit prices for both originator brands and their lowest-priced generics to estimate cost savings. Prices were adjusted to 2008 by using consumer price index data and were adjusted for purchasing power parity. For the medicines studied, an average of 9% to 89% could be saved by an individual country from a switch in private sector purchases from originator brands to lowest-priced generics. In public hospitals in China, US $ 370 million could be saved from switching only four medicines, saving an average of 65%. Across individual medicines, average potential savings ranged from 11% for beclometasone inhaler to 73% for ceftriaxone injection. Substantial savings could be achieved by switching private sector purchases from originator brand medicines to lowest-priced generic equivalents. Strategies to promote generic uptake, such as generic substitution by pharmacists and increasing confidence in generics by professionals and the public, should be included in national medicines policies. Copyright © 2012 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

  9. Project report on drawing district energy-saving visions for Town of Nishi Senboku; Nishi Senboku machi sho energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Studied in this project are concrete energy-saving procedures, and potentially saved energy and abated CO2 emissions in Town of Nishi Senboku, to promote energy saving and abatement of gas emissions which cause global warming. The energy-saving procedures studied include co-generation, utilization of waste heat, wind power generation, utilization of low-temperature heat by snow, fuel-efficient vehicles, use of insulators for houses, energy-saving type electric appliances, energy-saving activities, and eco-driving. The results indicate that the energy-saving activities and eco-driving can potentially more contribute to energy saving than the others. The study on introduction of energy-saving facilities in the 'Nukumori Hot Spring/Umeria' project indicates that the heat pump plus co-generation case is the most advantageous, because it can potentially reduce primary energy by 2,845,215MJ/y and CO2 emissions by 22,688kg-C/y. Introduction of energy-saving facilities is also studied for an information center in the Nishi-Senboku service area for the Akita Highway. The results indicate that the introduction can potentially reduce primary energy and CO2 emissions by 25 and 13%, respectively. (NEDO)

  10. Securing energy efficiency as a high priority. Scenarios for common appliance electricity consumption in Thailand

    Energy Technology Data Exchange (ETDEWEB)

    Foran, T. [Unit for Social and Environmental Research USER, Faculty of Social Sciences, Chiang Mai University, P.O. Box 144, Chiang Mai, 50200 (Thailand); Du Pont, P.T. [International Resources Group and Joint Graduate School of Energy and Environment, Bangkok (Thailand); Parinya, P. [The Joint Graduate School of Energy and Environment, King Mongkut' s University of Technology Thonburi, Bangkok (Thailand); Phumaraphand, N. [Electricity Generating Authority of Thailand, Nonthaburi (Thailand)

    2010-11-15

    Between 1995 and 2008, Thailand's energy efficiency programs produced an estimated total of 8,369 GWh/year energy savings and 1,471 MW avoided peak power. Despite these impressive saving figures, relatively little future scenario analysis is available to policy makers. Before the 2008 global financial crisis, electricity planners forecasted 5-6% long-term increases in demand. We explored options for efficiency improvements in Thailand's residential sector, which consumes more than 20% of Thailand's total electricity consumption of 150 TWh/year. We constructed baseline and efficient scenarios for the period 2006-2026, for air conditioners, refrigerators, fans, rice cookers, and compact fluorescent light bulbs. We drew on an appliance database maintained by Electricity Generating Authority of Thailand's voluntary labeling program. For the five appliances modeled, the efficiency scenario results in total savings of 12% of baseline consumption after 10 years and 29% of baseline after 20 years. Approximately 80% of savings come from more stringent standards for air conditioners, including phasing out unregulated air conditioner sales within 6 years. Shifting appliance efficiency standards to current best-in-market levels within 6 years produces additional savings. We discuss institutional aspects of energy planning in Thailand that thus far have limited the consideration of energy efficiency as a high-priority resource.

  11. Social Capital and Savings Behavior

    DEFF Research Database (Denmark)

    Newman, Carol; Tarp, Finn; Khai, Luu Duc

    In this paper, we analyze household savings in rural Vietnam paying particular attention to the factors that determine the proportion of savings held as formal deposits. Our aim is to explore the extent to which social capital can play a role in promoting formal savings behavior. Social capital...

  12. Saving water through global trade

    NARCIS (Netherlands)

    Chapagain, Ashok; Hoekstra, Arjen Ysbert; Savenije, H.H.G.

    2005-01-01

    Many nations save domestic water resources by importing water-intensive products and exporting commodities that are less water intensive. National water saving through the import of a product can imply saving water at a global level if the flow is from sites with high to sites with low water

  13. Energy saved neon sign lighting power supply for photovoltaic systems

    Energy Technology Data Exchange (ETDEWEB)

    Tanitteerapan, T.; Dokpikul, S.; Arunrungrasmi, S. [King Mongkut Univ. of Technology Thonburi, Bangmod, Tungkru, Bangkok (Thailand). Dept. of Electrical Technology Education, Faculty of Industrial Education

    2007-07-01

    Petroleum oil, natural gas and fossil fuels are commonly used in power plants for electrical power generation. However, because of their negative environmental impacts, energy and environmental savings from renewable energy resources are necessary choices. Solar energy can be converted to the electrical voltage by using solar arrays. This process can be used in many electrical applications. This paper introduced a neon sign lighting power supply for a small photovoltaic powered stand-alone commercial advertising board for a remote area in Thailand. The circuit implementation was very simple, consisting of an active switch device, a resonant capacitor and high frequency transformer. The control also operated as a fixed frequency and fixed duty ratio controller. The paper discussed the principle of neon sign lighting, power circuit operation, and control circuit operation. To verify the proposed power supply, the circuit experiment of the proposed power supply for the neon sign lighting was applied to a 10 foot long, 10 millimeter diameter bulb. The neon sign was ignited smoothly with little power consumption. 2 refs., 1 tab., 10 figs.

  14. Energy savings in CSFR - building sector

    International Nuclear Information System (INIS)

    Jacobsen, F.R.

    1993-01-01

    The Czechoslovak/Danish project on energy savings in buildings proves that it is possible to save up to 30% of the energy in buildings. 10% can be saved at an investment of 27 bill KCS. The total investment that is needed to save 30% is 140 bill KCS. Further energy savings can be obtained through more energy efficient supply systems. Information dissemination is important for the energy saving programme as are economic incentives. Investments in energy savings should be profitable for the investor, but this is not the case in the Czech and Slovak republics today. Changes are needed. Energy prices are still to low, compared to investment costs. Financial possibilities are not satisfactory for private investors. Price systems are not favourable to investment in energy savings. Training is needed for boiler men and energy consultants. Legislation is essential for the support of the full range of activities in the energy sector. Research and Development activities must back up the development of the sector. Pilot projects can illuminate the savings potential. The production of technical equipment for control and metering and production of insulation materials must be promoted. (AB)

  15. Electric power saving in the drinkable water, sewage and sanitation system, La Piedad; Ahorro de energia electrica en el sistema de agua potable, alcantarillado y saneamiento de La Piedad

    Energy Technology Data Exchange (ETDEWEB)

    Sistema de Agua Potable, Alcantarillado y Saneamiento de la Piedad (Mexico). E-mail: sapaslapiedad@prodigy.net.mx

    2006-04-15

    In Michoacan, Mexico, a project who seeks to benefice the Municipal public resources was crated in 1994. It would be achieved trough the electric power saving in the public lighting system, and drinkable water pumping and black water, since those activities required the budget biggest part. The program could be developed recently and the saving was significant. In addition the electromechanical efficiency increased in the equipment installation. This work is an example for other States to do something similar that can improve their conditions. [Spanish] En el estado de Michoacan, Mexico se creo un proyecto en el ano de 1994, el cual buscaba beneficiar los recursos publicos municipales, a traves del ahorro de la energia electrica en los sistemas de alumbrado publico y bombeo de agua potable y aguas negras, ya que estas actividades son las que requieren la mayor parte del presupuesto. El programa pudo llevarse a cabo en anos recientes y el ahorro fue significativo, ademas de que aumento la eficiencia electromecanica en los equipos que se instalaron, y esta obra ha servido de ejemplo a otros estados para que realicen algo similar que pueda mejorar su situacion.

  16. Reducing lighting electricity use in underground metro stations

    International Nuclear Information System (INIS)

    Casals, Miquel; Gangolells, Marta; Forcada, Núria; Macarulla, Marcel

    2016-01-01

    Highlights: • Lighting systems are big energy consumers in underground metro stations. • An adaptive lighting system strategy is developed for underground stations. • Dimming controls are based on station occupancy levels and maintenance cycles. • The k-means clustering technique is used to identify stations’ occupancy patterns. • Savings were found to amount to 255.47 MW h in 2 years for a case study metro network. - Abstract: Lighting systems are usually one of the largest electrical end-uses in underground metro stations. Taking into account that budget restrictions in publicly owned companies hinder energy efficiency retrofit projects that require high initial investments, affordable energy saving strategies are needed. This paper presents a low-cost approach for reducing lighting electricity use in underground stations, without affecting passengers’ comfort or the metro operator’s service. For this purpose, an adaptive lighting strategy of dimming the illuminance levels of artificial light sources has been developed. Dimming controls are based on the occupancy of the station, and the preventive maintenance and cleaning cycles of the luminaires. The stations’ monthly occupancy patterns are defined through the k-means clustering technique. To illustrate its effectiveness, the method was applied to 115 underground stations of the Barcelona metro network. The results revealed overall electricity savings of 255.47 MW h on a biannual basis, which represents 36.22% of the stations’ baseline lighting consumption. Individual energy savings were found to range from 25 to 87.5 MW h/year in the stations of the Barcelona metro network, depending on the number and profile of station users. The research findings will undoubtedly be useful for the future energy efficiency project plans of worldwide metro operators and managers of other underground spaces.

  17. Current and future greenhouse gas emissions associated with electricity generation in China: implications for electric vehicles.

    Science.gov (United States)

    Shen, Wei; Han, Weijian; Wallington, Timothy J

    2014-06-17

    China's oil imports and greenhouse gas (GHG) emissions have grown rapidly over the past decade. Addressing energy security and GHG emissions is a national priority. Replacing conventional vehicles with electric vehicles (EVs) offers a potential solution to both issues. While the reduction in petroleum use and hence the energy security benefits of switching to EVs are obvious, the GHG benefits are less obvious. We examine the current Chinese electric grid and its evolution and discuss the implications for EVs. China's electric grid will be dominated by coal for the next few decades. In 2015 in Beijing, Shanghai, and Guangzhou, EVs will need to use less than 14, 19, and 23 kWh/100 km, respectively, to match the 183 gCO2/km WTW emissions for energy saving vehicles. In 2020, in Beijing, Shanghai, and Guangzhou EVs will need to use less than 13, 18, and 20 kWh/100 km, respectively, to match the 137 gCO2/km WTW emissions for energy saving vehicles. EVs currently demonstrated in China use 24-32 kWh/100 km. Electrification will reduce petroleum imports; however, it will be very challenging for EVs to contribute to government targets for GHGs emissions reduction.

  18. Sosiaalisen median markkinoinnin vuosikello Weecos Oy:lle

    OpenAIRE

    Heinämäki, Lotta; Huuskonen, Leena

    2015-01-01

    Opinnäytetyön tarkoitus oli luoda kokonaisvaltainen ja selkeä suunnitelma Weecos Oy:n markkinointitoimenpiteille valituissa sosiaalisen median kanavissa. Weecos on vuonna 2012 perustettu ekologisia yrityksiä yhteen keräävä verkkokauppa-alusta. Pienestä koostaan johtuen se ei ole pystynyt toteuttamaan sosiaalisen median markkinointia toivomallaan tavalla ja markkinoinnin suunnittelu ja toteutus on ollut epäsäännöllistä. Markkinointisuunnitelman tavoitteena oli helpottaa yrityksen markkinoi...

  19. Estimating the Value of Life, Injury, and Travel Time Saved Using a Stated Preference Framework.

    Science.gov (United States)

    Niroomand, Naghmeh; Jenkins, Glenn P

    2016-06-01

    The incidence of fatality over the period 2010-2014 from automobile accidents in North Cyprus is 2.75 times greater than the average for the EU. With the prospect of North Cyprus entering the EU, many investments will need to be undertaken to improve road safety in order to reach EU benchmarks. The objective of this study is to provide local estimates of the value of a statistical life and injury along with the value of time savings. These are among the parameter values needed for the evaluation of the change in the expected incidence of automotive accidents and time savings brought about by such projects. In this study we conducted a stated choice experiment to identify the preferences and tradeoffs of automobile drivers in North Cyprus for improved travel times, travel costs, and safety. The choice of route was examined using mixed logit models to obtain the marginal utilities associated with each attribute of the routes that consumers choose. These estimates were used to assess the individuals' willingness to pay (WTP) to avoid fatalities and injuries and to save travel time. We then used the results to obtain community-wide estimates of the value of a statistical life (VSL) saved, the value of injury (VI) prevented, and the value per hour of travel time saved. The estimates for the VSL range from €315,293 to €1,117,856 and the estimates of VI from € 5,603 to € 28,186. These values are consistent, after adjusting for differences in incomes, with the median results of similar studies done for EU countries. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Industrial electricity demand and energy efficiency policy: The role of price changes and private R and D in the Swedish pulp and paper industry

    International Nuclear Information System (INIS)

    Henriksson, Eva; Söderholm, Patrik; Wårell, Linda

    2012-01-01

    The objective of this paper is to analyze electricity demand behaviour in the Swedish pulp and paper industry in the context of the increased interest in so-called voluntary energy efficiency programs. In these programs tax exemptions are granted if the participating firms carry out energy efficiency measures following an energy audit. We employ a panel data set of 19 pulp and paper firms, and estimate both the own- and cross-price elasticities of electricity demand as well as the impact of knowledge accumulation following private R and D on electricity use. The empirical results show that electricity use in the Swedish pulp and paper industry is relatively own-price insensitive, and the self-reported electricity savings following the voluntary so-called PFE program support the notion of important information asymmetries at the company level. However, the results display that already in a baseline setting pulp and paper firms tend to invest in private R and D that have electricity saving impacts, and our model simulations suggest that up to about one-third of the industry sector's self-reported electricity savings in PFE could be attributable to pure baseline effects. Future evaluations of voluntary energy efficiency programs must increasingly recognize the already existing incentives to reduce energy use in energy-intensive industries. - Highlights: ► We analyze electricity demand behaviour in the Swedish pulp and paper industry. ► An important context is the voluntary energy efficiency programs PFE. ► The electricity savings following PFE are significant, but price responses are low. ► Still, already in a baseline setting firms tend to invest in electricity-saving R and D. ► These baseline issues are not adequately addressed in PFE.

  1. Water withdrawal and consumption reduction analysis for electrical energy generation system

    Science.gov (United States)

    Nouri, Narjes

    There is an increasing concern over shrinking water resources. Water use in the energy sector primarily occurs in electricity generation. Anticipating scarcer supplies, the value of water is undoubtedly on the rise and design, implementation, and utilization of water saving mechanisms in energy generation systems are becoming inevitable. Most power plants generate power by boiling water to produce steam to spin electricity-generating turbines. Large quantities of water are often used to cool the steam in these plants. As a consequence, most fossil-based power plants in addition to consuming water, impact the water resources by raising the temperature of water withdrawn for cooling. A comprehensive study is conducted in this thesis to analyze and quantify water withdrawals and consumption of various electricity generation sources such as coal, natural gas, renewable sources, etc. Electricity generation for the state of California is studied and presented as California is facing a serious drought problem affecting more than 30 million people. Integrated planning for the interleaved energy and water sectors is essential for both water and energy savings. A linear model is developed to minimize the water consumption while considering several limitations and restrictions. California has planned to shut down some of its hydro and nuclear plants due to environmental concerns. Studies have been performed for various electricity generation and water saving scenarios including no-hydro and no-nuclear plant and the results are presented. Modifications to proposed different scenarios have been applied and discussed to meet the practical and reliability constraints.

  2. Seamless electricity trade between Canada and the U.S. northeast

    International Nuclear Information System (INIS)

    Bernard, J.T.; Clavet, F.; Ondo, J.C.

    2003-01-01

    In January 1997, the wholesale electricity market in the United States (U.S.) opened to competition following FERC Order 888 which allowed producers and local distribution companies to sell electricity at market prices. The deregulation of the wholesale electricity market in the U.S. is regarded as an opportunity for the Canadian electric power industry to increase profit. This paper examined the price and trade effects for Ontario, Quebec, New Brunswick, New York and New England resulting from the seamless border created by deregulation. Pre-1997 exchanges made possible fuel cost savings of $397.2 million per year. Deregulation added annual savings of $358.7 million. The main beneficiaries are Canadian regions because exports are priced at the marginal costs of the importing regions. Imports from the Canadian regions are not large enough to lower the marginal costs of the U.S. regions. Therefore, electricity deregulation across the border is not likely to greatly decrease prices in the U.S. regions. It was also noted that the U.S. is becoming more dependant upon Canadian electricity imports. Since wholesale markets were opened, greenhouse gas (GHG) emissions increased by 4.3 Mt of carbon dioxide equivalent because of the low cost of coal, mostly in Ontario. Trade patterns may change with growing electricity demand and environmental concerns. 17 refs., 12 tabs., 1 fig

  3. Modeling of electricity savings in the Danish household sector using Balmorel

    DEFF Research Database (Denmark)

    Trivella, Alessio; Baldini, Mattia

    In this paper we examine the investments in energy-efficient household appliances from an energy system perspective. We consider a set of ten appliances constituting the majority of the electricity consumption in the private household sector, and investigate whether investing in improved energy...... efficiency can compete with the cost of electricity supply from existing or new power plants. To assess the analysis, Balmorel, a linear optimization model for heat and power sectors, has been extended in order to assess the best possible investments in more efficient household appliances. The model is non......-exclusively tested on the Danish energy system under different scenarios, and computational experiments show that several energy efficiency measures in the household sector should be regarded as valuable investments, while others would require some form of support to become profitable. The analysis also reveals...

  4. Electrical system design status of PEFP

    Energy Technology Data Exchange (ETDEWEB)

    Song, In Taek; Mun, Kyeong Jun; Kim, Jun Yeon [KAERI, Daejeon (Korea, Republic of)

    2012-10-15

    Proton Engineering Frontier Project (PEFP) has been developing a 100 MeV proton linear accelerator. Also, PEFP has been designing the Proton Accelerator Research Center in Gyeongju. In site, we installed GIS (Gas Insulated Switchgear) to receive 154kV electric power and 154kV/3.3kV transformer. For the energy saving scheme, we are now installing solar power system, automatic lighting control system and maximum control power system of PEFP. In this paper, we described electrical power system of PEFP.

  5. Data on energy saving measures on the basis of real consumption data

    International Nuclear Information System (INIS)

    Menkveld, M.; Vethman, P.; Leidelmeijer, K.; Cozijnsen, E.

    2012-05-01

    On assignment of NLAgency, RIGO and ECN have established the indicative savings of energy saving measures in existing dwellings based on actual (measured) energy use data. This is done with statistical analysis on a database with energy uses and data on energy saving measures in dwellings. This database is made by combination of data on dwellings from the energy label database of NLAgency and registrations of actual electricity and gas use from the customer files of Statistics Netherlands. The energy label database contains the data used for the label calculation of the dwellings that have received a label. The information consists of the heating system, the type of boiler, insulation, the type of glass, the type of ventilation system, but also the type of dwelling, the size of the dwelling and the year of construction. Linkage of these databases by Statistics Netherlands leads to a file containing data on over 600.000 dwellings. The relations between energy saving measures and energy cannot simply be calculated by comparing average uses of dwellings with a high-efficiency boiler and dwellings with an improved-efficiency boiler. After all, these dwellings will most likely have more differences with regard to other features (for example the extent to which double glazing has been installed). Comparison of these averages would lead to an overestimation of the effect of implementing a high-efficiency boiler. The energy use in dwellings that have a high-efficiency boiler is expected to be lower because of a combination of (other) measures. To arrive at useful statements about savings and effects, certain features of the dwellings and other measures were verified in the analyses. A statistical check of variables examines whether the variable has any influence on a (possible) relation, and if this is true, the influence is subsequently 'corrected' mathematically. The statistical analysis has not only been conducted for the actual energy use data from the customer files

  6. The efficiency improvement potential for coal, oil and electricity in China's manufacturing sectors

    International Nuclear Information System (INIS)

    Li, Ke; Lin, Boqiang

    2015-01-01

    This paper introduces an improved total-factor ESTR (energy-saving target ratio) index, which combines the sequence technique and the “energy direction” to a DEA (data envelopment analysis) model, in order to measure the possible energy saving potential of a manufacturing sector. Afterward, the energy saving potentials of four different energy carriers, namely coal, gasoline, diesel oil and electricity, for 27 manufacturing sectors during the period of 1998–2011 in China are calculated. The results and its policy implications are as follows: (1) the average ESTRs of coal, gasoline, diesel oil and electricity are 1.714%, 49.939%, 24.465% and 3.487% respectively. Hence, energy saving of manufacturing sectors should put more emphasis on gasoline and diesel oil. (2) The key sectors for gasoline saving is the energy-intensive sectors, while the key sectors for diesel oil saving is the equipment manufacturing sectors. (3) The manufacture of raw chemical materials and chemical products sector not only consumes a large amount of oil, but also has a low efficiency of oil usage. Therefore, it is the key sector for oil saving. (4) Manufacture of tobacco and manufacture of communication equipment, computers and other electronic equipment are the benchmark for the four major energy carriers of energy-saving ratios. - Highlights: • An improved total-factor energy-saving target ratio is proposed. • Energy saving potentials of energy carriers for sectors in 1998–2011 are calculated. • Policy implications for energy savings in sectors and energy carriers are discussed. • Some suggestions for the energy policies of China's economy are discussed

  7. Co-evolution of electric and telecommunications networks

    Energy Technology Data Exchange (ETDEWEB)

    Rivkin, S.R.

    1998-05-01

    There are potentially significant societal benefits in co-evolution between electricity and telecommunications in the areas of common infrastructure, accelerated deployment of distributed energy, tighter integration of information flow for energy management and distribution, and improved customer care. With due regard for natural processes that are more potent than any regulation and more real than any ideology, the gains from co-evolution would far outweigh the attenuated and speculative savings from restructuring of electricity that is too simplistic.

  8. Energy efficiency improvements in electric motors and drives

    Energy Technology Data Exchange (ETDEWEB)

    Bertoldi, P. [Commission of the European Communities, Brussels (Belgium). Directorate General for Energy; Ameida, A.T. de [Coimbra Univ. (Portugal). Dept. de Engenharia Electrotecnica; Falkner, H. [eds.] [AEA Technolgy, Harwell (United Kingdom). ETSU

    2000-07-01

    This book covers the state of the art of energy-efficient electric motor technologies, which can be used now and in the near future to achieve significant and cost-effective energy savings. Recent developments in advanced motor technologies by some of the largest manufacturers of motors and drives are also presented. Although energy-efficient motor technologies can save a huge amount of electricity, they still have not been widely adopted. The barriers which can hinder the adoption of those technologies are presented. Policies and programmes to promote the large scale penetration of energy-efficient technologies and the market transformation are featured in the book, describing the experiences carried out in different parts of the world. This extensive coverage includes contributions from relevant institutions in the European Union, North America, Latin America, Japan, Australia and New Zealand. (orig.)

  9. SAVING BEHAVIOUR AND DETERMINANTS OF SAVING MOBILIZATION BY RURAL FINANCIAL CO-OPERATORS IN TIGRAI REGION, ETHIOPIA

    Directory of Open Access Journals (Sweden)

    Sebhatu Kifle Tesfamariam

    2012-01-01

    Full Text Available This paper identified and examined saving behaviour and determinants of saving mobiliza-tion by the rural co-operators in Southern Tigrai Ethiopia. The input for the study was ob-tained from randomly selected 120 rural household savers from six purposively selected ru-ral savings and credit cooperatives. The result of the study using least squares method showed that savings mobilized is determined by household annual income, amount of loan borrowed and year of member stay in the cooperative. These factors therefore have to be considered in designing strategies aimed at improving the saving mobilization of coopera-tive members in the study area. Besides, economically feasible cooperative societies in the region should be encouraged among the rural households by supporting them with revolv-ing funds as they are more effective and efficient in mobilizing rural savings and provide collateral plus guarantor-based loans with low default rate. This will enable them to boost up their production output and increase their savings thereby stimulating the rural economy.

  10. A decision support model for reducing electric energy consumption in elementary school facilities

    International Nuclear Information System (INIS)

    Hong, Taehoon; Koo, Choongwan; Jeong, Kwangbok

    2012-01-01

    Highlights: ► Decision support model is developed to reduce CO 2 emission in elementary schools. ► The model can select the school to be the most effective in energy savings. ► Decision tree improved the prediction accuracy by 1.83–3.88%. ► Using the model, decision-maker can save the electric-energy consumption by 16.58%. ► The model can make the educational-facility improvement program more effective. -- Abstract: The South Korean government has been actively promoting an educational-facility improvement program as part of its energy-saving efforts. This research seeks to develop a decision support model for selecting the facility expected to be effective in generating energy savings and making the facility improvement program more effective. In this research, project characteristics and electric-energy consumption data for the year 2009 were collected from 6282 elementary schools located in seven metropolitan cities in South Korea. In this research, the following were carried out: (i) a group of educational facilities was established based on electric-energy consumption, using a decision tree; (ii) a number of similar projects were retrieved from the same group of facilities, using case-based reasoning; and (iii) the accuracy of prediction was improved, using the combination of genetic algorithms, the artificial neural network, and multiple regression analysis. The results of this research can be useful for the following purposes: (i) preliminary research on the systematic and continuous management of educational facilities’ electric-energy consumption; (ii) basic research on electric-energy consumption prediction based on the project characteristics; and (iii) practical research for selecting an optimum facility that can more effectively apply an educational-facility improvement program as a decision support model.

  11. Connecting possibilistic prudence and optimal saving

    Directory of Open Access Journals (Sweden)

    Ana María Lucia Casademunt

    2013-12-01

    Full Text Available In this paper we study the optimal saving problem in the framework of possibility theory. The notion of possibilistic precautionary saving is introduced as a measure of the way the presence of possibilistic risk (represented by a fuzzy number influences a consumer in establishing the level of optimal saving. The notion of prudence of an agent in the face of possibilistic risk is defined and the equivalence between the prudence condition and a positive possibilistic precautionary saving is proved. Some relations between possibilistic risk aversion, prudence and possibilistic precautionary saving were established.

  12. The green electricity market model. Proposal for an optional, cost-neutral direct marketing model for supplying electricity customers

    International Nuclear Information System (INIS)

    Heinemann, Ronald

    2014-01-01

    One of the main goals of the Renewable Energy Law (EEG) is the market integration of renewable energy resources. For this purpose it has introduced compulsory direct marketing on the basis of a moving market premium. At the same time the green electricity privilege, a regulation which made it possible for customers to be supplied with electricity from EEG plants, has been abolished without substitution with effect from 1 August 2014. This means that, aside from other direct marketing channels, which will not be economically viable save for in a few exceptional cases, it will no longer be possible in future to sell electricity from EEG plants to electricity customers under the designation ''electricity from renewable energy''. The reason for this is that electricity sold under the market premium model can no longer justifiably be said to originate from renewable energy. As a consequence, almost all green electricity products sold in Germany carry a foreign green electricity certificate.

  13. Energy conservation and saving of materials by means of frequency control of blowers in the drying process of soap. Toerenregeling bij droger bespaart meer op grondstoffen dan op elektriciteit

    Energy Technology Data Exchange (ETDEWEB)

    Mezger, H.J. (Holec Systemen en Componenten BV, Hengelo (Netherlands))

    1992-07-01

    A fluidized-bed process is used in a Dutch soap factory to dry soap powder. By means of frequency control of the blower in the dryer a considerable amount of electricity can be saved. Frequency control also results in less loss of material during the start-up and stopping of the production process. The payback period of the frequency control systems is estimated at 1.5 year. Data are presented on the saving of electricity and on the saving of basic material. However, the frequency control system will not yet be implemented in the soap factory. First another drying technique (cooling by means of nitrogen, for which a fluidized-bed is not needed) will be tested. 4 figs., 2 tabs., 1 ref.

  14. Study on Electricity Purchase Optimization in Coordination of Electricity and Carbon Trading

    Science.gov (United States)

    Liu, Dunnan; Meng, Yaru; Zhang, Shuo

    2017-07-01

    With the establishment of carbon emissions trading market in China, the power industry has become an important part of the market participants. The power grid enterprises need to optimize their own strategies in the new environment of electricity market and carbon market coordination. First, the influence of electricity and carbon trading coordination on electricity purchase strategy for grid enterprises was analysed in the paper. Then a power purchase optimization model was presented, which used the minimum cost of low carbon, energy saving and environment protection as the goal, the power generation capacity, installed capacity and pollutant emission as the constraints. Finally, a provincial power grid was taken as an example to analyse the model, and the optimization order of power purchase was obtained, which provided a new idea for the low carbon development of power grid enterprises.

  15. Near-term hybrid vehicle program, phase 1. Appendix B: Design trade-off studies. [various hybrid/electric power train configurations and electrical and mechanical drive-line components

    Science.gov (United States)

    1979-01-01

    The relative attractiveness of various hybrid/electric power train configurations and electrical and mechanical drive-line components was studied. The initial screening was concerned primarily with total vehicle weight and economic factors and identified the hybrid power train combinations which warranted detailed evaluation over various driving cycles. This was done using a second-by-second vehicle simulation program which permitted the calculations of fuel economy, electricity usage, and emissions as a function of distance traveled in urban and highway driving. Power train arrangement possibilities were examined in terms of their effect on vehicle handling, safety, serviceability, and passenger comfort. A dc electric drive system utilizing a separately excited motor with field control and battery switching was selected for the near term hybrid vehicle. Hybrid vehicle simulations showed that for the first 30 mi (the electric range of the vehicle) in urban driving, the fuel economy was 80 mpg using a gasoline engine and 100 mpg using a diesel engine. In urban driving the hybrid would save about 75% of the fuel used by the conventional vehicle and in combined urban/highway driving the fuel saving is about 50%.

  16. Moonlight project promotes energy-saving technology

    Science.gov (United States)

    Ishihara, A.

    1986-01-01

    In promoting energy saving, development of energy conservation technologies aimed at raising energy efficiency in the fields of energy conversion, its transportation, its storage, and its consumption is considered, along with enactment of legal actions urging rational use of energies and implementation of an enlightenment campaign for energy conservation to play a crucial role. Under the Moonlight Project, technical development is at present being centered around the following six pillars: (1) large scale energy saving technology; (2) pioneering and fundamental energy saving technology; (3) international cooperative research project; (4) research and survey of energy saving technology; (5) energy saving technology development by private industry; and (6) promotion of energy saving through standardization. Heat pumps, magnetohydrodynamic generators and fuel cells are discussed.

  17. Saved Leave Scheme (SLS) : Simplified procedure for the transfer of leave to saved leave accounts

    CERN Multimedia

    HR Division

    2001-01-01

    As part of the process of streamlining procedures, the HR and AS Divisions have jointly developed a system whereby annual and compensatory leave will henceforth be automatically transferred1) to saved leave accounts. Under the provisions of the voluntary saved leave scheme (SLS), a maximum total of 10 days'2) annual and compensatory leave (excluding saved leave accumulated in accordance with the provisions of Administrative Circular No. 22 B) can be transferred to the saved leave account at the end of the leave year (30 September). Previously, every person taking part in the scheme has been individually issued with a form for the purposes of requesting the transfer of leave to the leave account and the transfer has then had to be done manually by HR Division. To streamline the procedure, unused leave of all those taking part in the saved leave scheme at the closure of of the leave-year accounts will henceforth be transferred automatically to the saved leave account on that date. This simplification is in the ...

  18. Energy-saving belt conveyors installed in Polish collieries

    Directory of Open Access Journals (Sweden)

    Jerzy ANTONIAK

    2010-01-01

    Full Text Available An important problem of reducing energy consumption and dioxide emissions in the stage of construction and operation of mine belt conveyors is connected with their broad use in the industry. However, this notion is related to a reduction of electric energy consumption for conveyor drive and for production of conveyor components and assemblies (belts, rollers, load-bearing structure etc.. An essential role is played by an increased life of belt conveyors assemblies and components, principally belts. A reduced electric energy consumption results in a decreased CO2 emissions, e.g. hard coal – fired power station issues 0.28 kg CO2 per production of 1 kWh, in to answer production of 1 t steel accounts for 3.2 t CO2 emissions. The subject-matter presented in the paper concerning energy-saving in the horizontally and inclined mine belt conveyors installed in a Polish colliery – Anna, Jankowice and Marcel, has a big economic significance and it is important from the point of view of environmental protection.

  19. Hybrid vehicle assessment. Phase I. Petroleum savings analysis

    Energy Technology Data Exchange (ETDEWEB)

    Levin, R.; Liddle, S.; Deshpande, G.; Trummel, M.; Vivian, H.

    1984-03-01

    This report presents the results of a comprehensive analysis of near-term electric-hybrid vehicles. Its purpose was to estimate their potential to save significant amounts of petroleum on a national scale in the 1990s. Performance requirements and expected annual usage patterns of these vehicles were first modeled. The projected US fleet composition was estimated, and conceptual hybrid vehicle designs were conceived and analyzed for petroleum use when driven in the expected annual patterns. These petroleum consumption estimates were then compared to similar estimates for projected 1990 conventional vehicles having the same performance and driven in the same patterns. Results are presented in the form of three utility functions and comparisons of several conceptual designs are made. The Hybrid Vehicle (HV) design and assessment techniques are discussed and a general method is explained for selecting the optimum energy management strategy for any vehicle-mission-battery combination. A discussion of lessons learned during the construction and test of the General Electric Hybrid Test Vehicle is also presented. Conclusions and recommendations are presented, and development recommendations are identified.

  20. Resistive flux saving and current profile control during lower hybrid waves assisted current rise in TORE SUPRA

    International Nuclear Information System (INIS)

    van Houtte, D.; Hoang, G.T.; Joffrin, E.; Lecoustey, P.; Moreau, D.; Parlange, F.; Tonon, G.; Vallet, J.C.

    1992-01-01

    Resistive flux saving at densities n e = (1 - 2) x 10 19 m -3 has been studied. High flux saving efficiency (0.7 x 10 13 Wb/J/m -1 ) can be achieved for a low rf power (P LH = 0.5 MW) due to the beneficial effect of the electric field on the suprathermal electrons. However for power higher than 1 MW, the efficiency is 0.25 x 10 13 Wb/J/m -1 . This flux saving efficiency is comparable to the one obtained during the flat top phase. The application of the LH power during a low density current ramp-up tends to peak the electron temperature and current density profiles. The rf power level, the parallel wavenumber and the current ramp rate allow to control the trajectories of the plasma discharges during the current rise inside the MHD stable domain

  1. Carbon and Energy Saving Financial Opportunities in the Industrial Compressed Air Sector

    Science.gov (United States)

    Vittorini, Diego; Cipollone, Roberto

    2017-08-01

    The transition towards a more sustainable energy scenario calls for both medium-to-long and short term interventions, with CO2 reduction and fossil fuel saving as main goals for all the Countries in the World. Among all others, one way to support these efforts is the setting-up of immaterial markets able to regulate, in the form of purchase and sales quotas, CO2 emissions avoided and fossil fuels not consumed. As a consequence, the upgrade of those sectors, characterized by high energy impact, is currently more than an option due to the related achievable financial advantage on the afore mentioned markets. Being responsible for about 10% electricity consumption in Industry, the compressed air sector is currently addressed as extremely appealing, when CO2 emissions and burned fossil fuels saving are in question. In the paper, once a standard is defined for compressors performances, based on data from the Compressed Air and Gas Institute and PNEUROP, the achievable energy saving is evaluated along with the effect in terms of CO2 emissions: with reference to those contexts in which mature intangible markets are established, an estimation of the financial benefit from savings sale on correspondent markets is possible, in terms of both avoided CO2 and fossil fuels not burned. The approach adopted allows to extend the analysis results to every context of interest, by applying the appropriate emission factor to the datum on compressor specific consumption.

  2. Impacts of the 2011 Tohoku earthquake on electricity demand in Japan. State space approach

    International Nuclear Information System (INIS)

    Honjo, Keita; Ashina, Shuichi

    2017-01-01

    Some papers report that consumers' electricity saving behavior (Setsuden) after the 2011 Tohoku Earthquake resulted in the reduction of the domestic electricity demand. However, time variation of the electricity saving effect (ESE) has not yet been sufficiently investigated. In this study, we develop a state space model of monthly electricity demand using long-term data, and estimate time variation of the ESE. We also estimate time variation of CO_2 emissions caused by Setsuden. Our result clearly indicates that Setsuden after the earthquake was not temporary but became established as a habit. Between March 2011 and October 2015, the ESE on power demand ranged from 2.9% to 6.9%, and the ESE on light demand ranged from 2.6% to 9.0%. The ESE on the total electricity demand was 3.2%-7.5%. Setsuden also contributed to the reduction of CO_2 emissions, but it could not offset the emissions increase caused by the shutdown of nuclear power plants. (author)

  3. Study on Chinese model of low carbon economy-energy-electricity-environment

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Zhaoguang

    2010-09-15

    With the successful experience on energy efficiency in the past 30 years in China, it can be summarized as Energy Usage Management(EUM) and Integrated Resource Strategic Planning(IRSP). They will play essential role in Low Carbon Economy. The model of Low Carbon Economy-Energy-Electricity-Environment and an outlook of Chinese economic growth, energy-electricity demand, and renewable energy generation have been studied in this paper. It has been shown that China would save energy 4.38 billion toe and reduce CO2 emission 16.55 billion ton by EUM, and would save energy 1.5 billion toe and reduce CO2 emission 5.7 Btons by IRSP during 2010-2030.

  4. Electricity tariffs used as an energy policy measure, progressive rates etc. Tariffer anvendt som styringsmiddel - progressive tariffer m. m

    Energy Technology Data Exchange (ETDEWEB)

    Tohmatsu, Takaomi

    1987-01-01

    Japan is scarce in natural resources, and 90% of our primary energy is imported from foreign countries (1973 statistics). This percentage is extremely high compared to other countries, and only since the first oil ''shock'' of 1973 to 74 has ''Energy Saving'' become the most important and urgent target of Japanese economic policies. The electricity supply industry is no exception. Since the industry occupies a vital share of national energy supplies, the electricity rate system was regarded as one of the most important tools for promoting energy saving. The best example is the ''incremental rate system'' adopted at the time of rate revision in 1974. Electricity costs soared after the first oil crisis, and the government's Electric Utility Industry Council, an advisory board to the Minister of International Trade and Industry (MITI), issued a recommendation to adopt the ''incremental rate system'' as follows: 1. special rate system for power customers; 2. three block inverted rate system for lighting customers. The energy situation has changed and the incremental rate system seems to have terminated its role. However, the Japanese structure of energy supply is still vulnerable to situational changes, and we believe it necessary to continue promoting energy saving efforts. The role of the rate system is changing from such systems as the ''incremental rate system'' which aims to directly control energy consumption. to such systems as a ''midnight power rate'' or a ''seasonal and time of use rate'' which is aimed at load leveling as well as energy saving. In any case, the responsibility of the electricity supply industry to save energy and reduce service costs, must be achieved through the development of electricity utilization technology and improvements to rate system. We are determined to continue further study with this point of view. (EG).

  5. The EKZ goes to its customers: A mobile exhibition on energy saving. Die EKZ gehen zu ihren Kunden: Rollende Austellungen ueber Energiesparen

    Energy Technology Data Exchange (ETDEWEB)

    Kurth, R.; Starkemann, B. (Elektrizitaetswerke Zurich (Switzerland))

    1991-09-18

    The Elektrizitaetswerke des Kantons Zuerich (EKZ) is bringing the subject of power and energy-saving closer to its customers with mobile exhibitions. Starting in the autumn of 1991, three new exhibition vehicles will be touring around the EKZ supply area they will give information on modern forms of lighting with power-saving light bulbs, on the heating of buildings by means of electrical heat pumps, on microwave appliances and power production from solar energy. (orig.).

  6. Study on China's low carbon development in an Economy-Energy-Electricity-Environment framework

    International Nuclear Information System (INIS)

    Hu Zhaoguang; Yuan Jiahai; Hu Zheng

    2011-01-01

    Emissions mitigation is a major challenge for China's sustainable development. We summarize China's successful experiences on energy efficiency in past 30 years as the contributions of Energy Usage Management and Integrated Resource Strategic Planning, which are essential for low-carbon economy. In an Economy-Energy-Electricity-Environment (E4) framework, the paper studies the low-carbon development of China and gives an outlook of China's economy growth, energy-electricity demand, renewable power generation and energy conservation and emissions mitigation until 2030. A business-as-usual scenario is projected as baseline for comparison while low carbon energy and electricity development path is studied. It is defined as low carbon energy/electricity when an economy body manages to realize its potential economic growth fueled by less energy/electricity consumption, which can be characterized by indexes of energy/electricity intensity and emissions per-unit of energy consumption (electricity generation). Results show that, with EUM, China, could save energy by 4.38 billion ton oil equivalences (toes) and reduce CO 2 emission by 16.55 billion tons; with IRSP, China, could save energy by 1.5 Btoes and reduce CO 2 emission by 5.7 Btons, during 2010-2030. To realize the massive potential, China has to reshape its economic structure and rely much on technology innovation in the future. - Research highlights: → In an E4 framework China's low-carbon development is compared with BAU scenario. → Low carbon energy/electricity and their related measuring indexes are discussed. → China's successful experiences on energy efficiency are summarized as EUM and IRSP. → With them China could save energy by 5.8 Btoe and reduce CO 2 by 22.2 Bton until 2030. → China must restructure its economy and rely on technology innovation for them.

  7. User-driven Points for Feedback Motivated Electricity savings in Private Households

    DEFF Research Database (Denmark)

    Kanstrup, Anne Marie; Christiansen, Ellen Tove

    This paper reports from a study of design and exploration of feedback for motivated electricity consumption to private households based on user-driven innovation. Traditionally feedback is designed on the basis of technical possibilities and/or theories on consumer behavior. In this study we...

  8. New TA Index-Based Rollover Prevention System for Electric Vehicles

    OpenAIRE

    Xiang Liu; Min Xu; Mian Li

    2015-01-01

    In addition to clean transportation and energy savings, electric vehicles can inherently offer better performance in the field of active safety and dynamic stability control, thanks to the superior fast and accurate control characteristics of electric motors. With the novel wheel status parameter TA for electric vehicles proposed by the authors in an earlier publication, a new TA index (TAI)-based rollover prevention method is presented in this paper to improve the driving performance of EV...

  9. Energy saving screw compressor technology; Energiebesparende schroefcompressortechnologie

    Energy Technology Data Exchange (ETDEWEB)

    Moeller, A. [RefComp, Lonigo (Italy); Neus, M. [Delta Technics Engineering, Breda (Netherlands)

    2011-03-15

    Smart solutions to reduce the energy consumption are continuously part of investigation in the refrigeration technology. This article subscribed the technology on which way energy can be saved at the operation of screw compressors which are used in air conditioners and refrigerating machinery. The combination of frequency control and Vi-control (intrinsic volumetric ratio) such as researched in the laboratory of RefComp is for the user attractive because the energy efficiency during part load operation is much better. Smart uses of thermodynamics, electric technology and electronic control are the basics of these applications. According to the manufacturer's information it is possible with these new generation screw compressors to save approx. 26% energy in comparison with the standard screw compressor. [Dutch] In dit artikel wordt de technologie omschreven waarmee veel energie bespaard kan worden bij schroefcompressoren die worden gebruikt in airconditioningsystemen en koel- en vriesinstallaties. De combinatie van frequentieregeling en Vi- regeling (Vi is de intrinsieke volumetrische verhouding) zoals onderzocht in het laboratorium van RefComp biedt de gebruiker veel voordelen doordat de energie-efficintie van de compressor tijdens deellast enorm wordt verbeterd. Slim gebruik van thermodynamika, elektrotechniek en elektronica vormen de basis van deze toepassing. Volgens de fabrikant kan met deze nieuwe generatie schroefcompressoren circa 26 procent op het energiegebruik tijdens deellast worden bespaard in vergelijking met de standaard serie schroefcompressoren.

  10. Evolution of China's power dispatch principle and the new energy saving power dispatch policy

    International Nuclear Information System (INIS)

    Ciwei, Gao; Yang, Li

    2010-01-01

    With social economic reform in the past decades, the power industry of China is gradually evolving from a highly integrated one toward an electricity market, which can be characterized based on the transition of the power dispatch principle. To attract investment in the power generating industry, China introduced non-state-owned power plants to the original system of a highly vertically integrated power industry with annual power generation quota guarantees, which makes the traditional economic dispatch principle not applicable. The newly debuted energy saving power dispatch (ESPD) is an attempt to fully exploit the maximum energy savings and was implemented by an administrative code. Starting in August 2007, the pilot operation of the ESPD was implemented in five provinces, but after two years, it is still not widely applied all over the country. This paper details the transition of China's power dispatch principle with particular attention to its origin and content. Moreover, the factors that influence the ESPD's actual energy saving effect are discussed, as well as the sustainability of the policy. (author)

  11. Reinforcement Learning and Savings Behavior.

    Science.gov (United States)

    Choi, James J; Laibson, David; Madrian, Brigitte C; Metrick, Andrew

    2009-12-01

    We show that individual investors over-extrapolate from their personal experience when making savings decisions. Investors who experience particularly rewarding outcomes from saving in their 401(k)-a high average and/or low variance return-increase their 401(k) savings rate more than investors who have less rewarding experiences with saving. This finding is not driven by aggregate time-series shocks, income effects, rational learning about investing skill, investor fixed effects, or time-varying investor-level heterogeneity that is correlated with portfolio allocations to stock, bond, and cash asset classes. We discuss implications for the equity premium puzzle and interventions aimed at improving household financial outcomes.

  12. Reinforcement Learning and Savings Behavior*

    Science.gov (United States)

    Choi, James J.; Laibson, David; Madrian, Brigitte C.; Metrick, Andrew

    2009-01-01

    We show that individual investors over-extrapolate from their personal experience when making savings decisions. Investors who experience particularly rewarding outcomes from saving in their 401(k)—a high average and/or low variance return—increase their 401(k) savings rate more than investors who have less rewarding experiences with saving. This finding is not driven by aggregate time-series shocks, income effects, rational learning about investing skill, investor fixed effects, or time-varying investor-level heterogeneity that is correlated with portfolio allocations to stock, bond, and cash asset classes. We discuss implications for the equity premium puzzle and interventions aimed at improving household financial outcomes. PMID:20352013

  13. Energy and cost savings results for advanced technology systems from the Cogeneration Technology Alternatives Study /CTAS/

    Science.gov (United States)

    Sagerman, G. D.; Barna, G. J.; Burns, R. K.

    1979-01-01

    The Cogeneration Technology Alternatives Study (CTAS), a program undertaken to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the 1985-2000 time period, is described, and preliminary results are presented. Two cogeneration options are included in the analysis: a topping application, in which fuel is input to the energy conversion system which generates electricity and waste heat from the conversion system is used to provide heat to the process, and a bottoming application, in which fuel is burned to provide high temperature process heat and waste heat from the process is used as thermal input to the energy conversion system which generates energy. Steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics are examined. Expected plant level energy savings, annual energy cost savings, and other results of the economic analysis are given, and the sensitivity of these results to the assumptions concerning fuel prices, price of purchased electricity and the potential effects of regional energy use characteristics is discussed.

  14. Use of landfill gas will save money and reduce emissions

    International Nuclear Information System (INIS)

    Espinosa, G.G.

    1991-01-01

    The City of Glendale, California has commenced on a project to transport landfill gas (LFG) from the Scholl Canyon Landfill to the Grayson Power Plant. At the plant the LFG will be used to produce electricity in existing steam electric generating units and combustion turbines. The LFG will reduce the natural gas consumed at the plant resulting in a substantial cost savings for the City. This project also offers significant environmental improvements. First, the elimination of flaring at the landfill will reduce emissions. Second, the LFG will reduce NO x emissions from the power plant. This paper will describe the existing collection system at the landfill as well as the design of the compression and piping system to transport the LFG to the power plant. It will also outline the in-plant modifications to the fuel delivery system and examine some of the emission implications of how the fuel is utilized

  15. Retrospective modeling of the merit-order effect on wholesale electricity prices from distributed photovoltaic generation in the Australian National Electricity Market

    International Nuclear Information System (INIS)

    McConnell, Dylan; Hearps, Patrick; Eales, Dominic; Sandiford, Mike; Dunn, Rebecca; Wright, Matthew; Bateman, Lachlan

    2013-01-01

    In electricity markets that use a merit order dispatch system, generation capacity is ranked by the price that it is bid into the market. Demand is then met by dispatching electricity according to this rank, from the lowest to the highest bid. The last capacity dispatched sets the price received by all generation, ensuring the lowest cost provision of electricity. A consequence of this system is that significant deployments of low marginal cost electricity generators, including renewables, can reduce the spot price of electricity. In Australia, this prospect has been recognized in concern expressed by some coal-fired generators that delivering too much renewable generation would reduce wholesale electricity prices. In this analysis we calculate the likely reduction of wholesale prices through this merit order effect on the Australian National Electricity Market. We calculate that for 5 GW of capacity, comparable to the present per capita installation of photovoltaics in Germany, the reduction in wholesale prices would have been worth in excess of A$1.8 billion over 2009 and 2010, all other factors being equal. We explore the implications of our findings for feed-in tariff policies, and find that they could deliver savings to consumers, contrary to prevailing criticisms that they are a regressive form of taxation. - Highlights: ► We model the impact of photovoltaic generation on the Australian electricity market. ► Photovoltaic generation depresses electricity prices, particularly in summer peaks. ► Over the course of a year, the depression in wholesale prices has significant value. ► 5 GW of solar generation would have saved $1.8 billion in the market over two years. ► The depression of wholesale prices offsets the cost of support mechanisms

  16. Energy savings solutions: passive solar design in Iranian cold climate

    Energy Technology Data Exchange (ETDEWEB)

    Nassehzadeh Tabriz, Shahram [Department of Architecture, Miyaneh Branch, Islamic Azad University (Iran, Islamic Republic of)], email: sh_nassehzadeh@m-iau.ac.ir; Mahdavi Tabatabaei Fard, Fariborz [SABAT TARH CO. (Iran, Islamic Republic of)], email: sabat_arc@yahoo.com; Aliyev, Fagan [International Eco-energy Academy (Azerbaijan)], email: ie_academy@yahoo.com

    2011-07-01

    In recent years, there has been a significant increase in the cost of fuel gas, fuel oil and electricity and much thought has been given to the use of solar energy. Living in a solar heated house gives peace of mind and body and it makes good sense in mountainous regions. Severe winters in such regions make more energy for standard living activities in buildings necessary. This paper discusses passive solar building design as an energy saving solution. In this type of design, windows, walls and floors act as storage and distribution devices for solar energy in winter and deflect solar heat in summer. Passive solar design techniques influence the choice of building site, design and materials within the general framework of enriching the quality of life of the inhabitants. As a result, natural resources are saved and the environment is conserved for future generations. In conclusion, it is seen that passive design keeps a home cool and comfortable in summer and warm and cozy in winter with minimal heating and cooling requirements.

  17. Energy-saving analysis of hydraulic hybrid excavator based on common pressure rail.

    Science.gov (United States)

    Shen, Wei; Jiang, Jihai; Su, Xiaoyu; Karimi, Hamid Reza

    2013-01-01

    Energy-saving research of excavators is becoming one hot topic due to the increasing energy crisis and environmental deterioration recently. Hydraulic hybrid excavator based on common pressure rail (HHEC) provides an alternative with electric hybrid excavator because it has high power density and environment friendly and easy to modify based on the existing manufacture process. This paper is focused on the fuel consumption of HHEC and the actuator dynamic response to assure that the new system can save energy without sacrificing performance. Firstly, we introduce the basic principle of HHEC; then, the sizing process is presented; furthermore, the modeling period which combined mathematical analysis and experiment identification is listed. Finally, simulation results show that HHEC has a fast dynamic response which can be accepted in engineering and the fuel consumption can be reduced 21% to compare the original LS excavator and even 32% after adopting another smaller engine.

  18. Replacement of pneumatic and hydraulic drives with electrical drives - Analysis of potential; Ersatz von pneumatischen und hydraulischen Antrieben durch Elektroantriebe. Potentialanalyse

    Energy Technology Data Exchange (ETDEWEB)

    Berchten, S. [BEngineering, Bassersdorf (Switzerland); Ritz, Ch. [Schnyder Ingenieure AG, Steg (Switzerland)

    2006-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) discusses the potential offered by modern technologies to save energy. The replacement of energy-intensive methods of providing physical movement - such as with pneumatic and hydraulic drives - with electrical drives is discussed. Based on existing installations in industry, an estimate of the potential for making savings is presented. This shows that large energy savings can be made by directly converting electrical into mechanical energy. Using real world examples, end-users and decision-makers are shown two profit-scenarios involving the purchase of a new system or retrofitting an existing system. The scenarios take investments, operating costs and system life-cycle into account. Extrapolations provide estimates of savings-potentials for the Swiss electricity market. Various market sectors are looked at, including the metal-working, chemical, foodstuffs and packaging sectors. Examples of installations actually implemented, where electro-mechanical systems have replaced pneumatic and hydraulic drives, are given.

  19. Electrical cardioversion

    Science.gov (United States)

    Sucu, Murat; Davutoglu, Vedat; Ozer, Orhan

    2009-01-01

    External electrical cardioversion was first performed in the 1950s. Urgent or elective cardioversions have specific advantages, such as termination of atrial and ventricular tachycardia and recovery of sinus rhythm. Electrical cardioversion is life-saving when applied in urgent circumstances. The succcess rate is increased by accurate tachycardia diagnosis, careful patient selection, adequate electrode (paddles) application, determination of the optimal energy and anesthesia levels, prevention of embolic events and arrythmia recurrence and airway conservation while minimizing possible complications. Potential complications include ventricular fibrillation due to general anesthesia or lack of synchronization between the direct current (DC) shock and the QRS complex, thromboembolus due to insufficient anticoagulant therapy, non-sustained VT, atrial arrhythmia, heart block, bradycardia, transient left bundle branch block, myocardial necrosis, myocardial dysfunction, transient hypotension, pulmonary edema and skin burn. Electrical cardioversion performed in patients with a pacemaker or an incompatible cardioverter defibrillator may lead to dysfunction, namely acute or chronic changes in the pacing or sensitivity threshold. Although this procedure appears fairly simple, serious consequences might occur if inappropriately performed. PMID:19448376

  20. Evolution of residential electricity demand by end-use in Quebec 1979-1989: A conditional demand analysis

    International Nuclear Information System (INIS)

    Lafrance, G.; Perron, D.

    1994-01-01

    Some of the main conclusions are presented from a temporal analysis of three large-scale electricity demand surveys (1979, 1984, and 1989) for the Quebec residential sector. A regression method called conditional demand analysis was used. The study allows a number of conclusions about certain electricity consumption trends by end-uses from 1979 to 1989 by household type and by vintage category. For example, the results indicate that decreasing electricity consumption between 1979 and 1984 for a typical dwelling equipped with electric space heating was mainly related to a large decline in net heating consumption. Overall, the results suggest that some permanent energy savings have been realized by a typical household equipped with an electric heating system due to improvements in standards and changes in customer behavior. These energy savings were partly offset by increased electricity consumption from the purchase of new appliances and an increase in the demand for hot water. 7 refs., 1 fig., 8 tabs

  1. Saving for Success: Financial Education and Savings Goal Achievement in Individual Development Accounts

    Science.gov (United States)

    Grinstead, Mary L.; Mauldin, Teresa; Sabia, Joseph J.; Koonce, Joan; Palmer, Lance

    2011-01-01

    Using microdata from the American Dream Demonstration, the current study examines factors associated with savings and savings goal achievement (indicated by a matched withdrawal) among participants of individual development account (IDA) programs. Multinomial logit results show that hours of participation in financial education programs, higher…

  2. Short-Term Saved Leave Scheme

    CERN Multimedia

    2007-01-01

    As announced at the meeting of the Standing Concertation Committee (SCC) on 26 June 2007 and in http://Bulletin No. 28/2007, the existing Saved Leave Scheme will be discontinued as of 31 December 2007. Staff participating in the Scheme will shortly receive a contract amendment stipulating the end of financial contributions compensated by save leave. Leave already accumulated on saved leave accounts can continue to be taken in accordance with the rules applicable to the current scheme. A new system of saved leave will enter into force on 1 January 2008 and will be the subject of a new implementation procedure entitled "Short-term saved leave scheme" dated 1 January 2008. At its meeting on 4 December 2007, the SCC agreed to recommend the Director-General to approve this procedure, which can be consulted on the HR Department’s website at the following address: https://cern.ch/hr-services/services-Ben/sls_shortterm.asp All staff wishing to participate in the new scheme a...

  3. Short-Term Saved Leave Scheme

    CERN Multimedia

    HR Department

    2007-01-01

    As announced at the meeting of the Standing Concertation Committee (SCC) on 26 June 2007 and in http://Bulletin No. 28/2007, the existing Saved Leave Scheme will be discontinued as of 31 December 2007. Staff participating in the Scheme will shortly receive a contract amendment stipulating the end of financial contributions compensated by save leave. Leave already accumulated on saved leave accounts can continue to be taken in accordance with the rules applicable to the current scheme. A new system of saved leave will enter into force on 1 January 2008 and will be the subject of a new im-plementation procedure entitled "Short-term saved leave scheme" dated 1 January 2008. At its meeting on 4 December 2007, the SCC agreed to recommend the Director-General to approve this procedure, which can be consulted on the HR Department’s website at the following address: https://cern.ch/hr-services/services-Ben/sls_shortterm.asp All staff wishing to participate in the new scheme ...

  4. Advanced electrical power system technology for the all electric aircraft

    Science.gov (United States)

    Finke, R. C.; Sundberg, G. R.

    1983-01-01

    The application of advanced electric power system technology to an all electric airplane results in an estimated reduction of the total takeoff gross weight of over 23,000 pounds for a large airplane. This will result in a 5 to 10 percent reduction in direct operating costs (DOC). Critical to this savings is the basic electrical power system component technology. These advanced electrical power components will provide a solid foundation for the materials, devices, circuits, and subsystems needed to satisfy the unique requirements of advanced all electric aircraft power systems. The program for the development of advanced electrical power component technology is described. The program is divided into five generic areas: semiconductor devices (transistors, thyristors, and diodes); conductors (materials and transmission lines); dielectrics; magnetic devices; and load management devices. Examples of progress in each of the five areas are discussed. Bipolar power transistors up to 1000 V at 100 A with a gain of 10 and a 0.5 microsec rise and fall time are presented. A class of semiconductor devices with a possibility of switching up to 100 kV is described. Solid state power controllers for load management at 120 to 1000 V and power levels to 25 kW were developed along with a 25 kW, 20 kHz transformer weighing only 3.2 kg. Previously announced in STAR as N83-24764

  5. Advanced electrical power system technology for the all electric aircraft

    Science.gov (United States)

    Finke, R. C.; Sundberg, G. R.

    1983-01-01

    The application of advanced electric power system technology to an all electric airplane results in an estimated reduction of the total takeoff gross weight of over 23,000 pounds for a large airplane. This will result in a 5 to 10 percent reduction in direct operating costs (DOC). Critical to this savings is the basic electrical power system component technology. These advanced electrical power components will provide a solid foundation for the materials, devices, circuits, and subsystems needed to satisfy the unique requirements of advanced all electric aircraft power systems. The program for the development of advanced electrical power component technology is described. The program is divided into five generic areas: semiconductor devices (transistors, thyristors, and diodes); conductors (materials and transmission lines); dielectrics; magnetic devices; and load management devices. Examples of progress in each of the five areas are discussed. Bipolar power transistors up to 1000 V at 100 A with a gain of 10 and a 0.5 microsec rise and fall time are presented. A class of semiconductor devices with a possibility of switching up to 100 kV is described. Solid state power controllers for load management at 120 to 1000 V and power levels to 25 kW were developed along with a 25 kW, 20 kHz transformer weighing only 3.2 kg.

  6. Risk transfer via energy savings insurance; TOPICAL

    International Nuclear Information System (INIS)

    Mills, Evan

    2001-01-01

    Among the key barriers to investment in energy efficiency improvements are uncertainties about attaining projected energy savings and apprehension about potential disputes over these savings. The fields of energy management and risk management are thus intertwined. While many technical methods have emerged to manage performance risks (e.g. building commissioning), financial risk transfer techniques are less developed in the energy management arena than in other more mature segments of the economy. Energy Savings Insurance (ESI) - formal insurance of predicted energy savings - is one method of transferring financial risks away from the facility owner or energy services contractor. ESI offers a number of significant advantages over other forms of financial risk transfer, e.g. savings guarantees or performance bonds. ESI providers manage risk via pre-construction design review as well as post-construction commissioning and measurement and verification of savings. We found that the two mos t common criticisms of ESI - excessive pricing and onerous exclusions - are not born out in practice. In fact, if properly applied, ESI can potentially reduce the net cost of energy savings projects by reducing the interest rates charged by lenders, and by increasing the level of savings through quality control. Debt service can also be ensured by matching loan payments to projected energy savings while designing the insurance mechanism so that payments are made by the insurer in the event of a savings shortfall. We estimate the U.S. ESI market potential of$875 million/year in premium income. From an energy-policy perspective, ESI offers a number of potential benefits: ESI transfers performance risk from the balance sheet of the entity implementing the energy savings project, thereby freeing up capital otherwise needed to ''self-insure'' the savings. ESI reduces barriers to market entry of smaller energy services firms who do not have sufficiently strong balance sheets to self

  7. Optimizing plug-in electric vehicle charging in interaction with a small office building

    Energy Technology Data Exchange (ETDEWEB)

    Momber, Ilan; Gomez, Tomas [Instituto de Investigacion Tecnologica (IIT), Madrid (Spain); Dallinger, David; Beer, Sebastian; Wietschel, Martin [Fraunhofer Institute for Systems and Innovation Research, Karlsruhe (Germany). Competence Center Energy Policy and Energy Systems; Marnay, Chris; Stadler, Michael [Lawrence Berkeley Lab., CA (United States)

    2011-07-01

    This paper considers the integration of plug-in electric vehicles (PEVs) in micro-grids. Extending a theoretical framework for mobile storage connection, the economic analysis here turns to the interactions of commuters and their driving behavior with office buildings. An illustrative example for a real office building is reported. The chosen system includes solar thermal, photovoltaic, combined heat and power generation as well as an array of plug-in electric vehicles with a combined aggregated capacity of 864 kWh. With the benefit-sharing mechanism proposed here and idealized circumstances, estimated cost savings of 5% are possible. Different pricing schemes were applied which include flat rates, demand charges, as well as hourly variable final customer tariffs and their effects on the operation of intermittent storage were revealed and examined in detail. Because the plug-in electric vehicle connection coincides with peak heat and electricity loads as well as solar radiation, it is possible to shift energy demand as desired in order to realize cost savings. (orig.)

  8. Semiconductors enable efficient solutions in electric vehicles; Halbleiter ermoeglichen effiziente Loesungen in Elektrofahrzeugen

    Energy Technology Data Exchange (ETDEWEB)

    Adlkofer, Hans [Infineon Technologies AG, Muenchen (Germany)

    2010-07-01

    The automotive industry currently enters a new phase of the competition. The successful addressing of vehicles with electric motors is in the focus of he competition. Electric vehicles which save the electrical energy in batteries may not replace immediately all fuel-powered vehicles in the given transport infrastructure. The semiconductor industry needs to provide solutions and technologies in order to increase the efficiency of electric vehicles and further to reduce the operating costs. Thus, the author of the contribution under consideration reports on possible ways to this target using a battery balancing system considering the amortization of such a system. The presented active battery cell management system may monitor the charging and discharging of the battery by means of a software monitor so that an energy recovery system is supported optimally. It ensures a reliable operation, prevents accidental premature battery failure and enables cost savings of about 10 % for the whole set of batteries.

  9. Electricity savings ``soon come'' to Jamaica -- Assessing the potential for air conditioning and refrigeration end-use DSM

    Energy Technology Data Exchange (ETDEWEB)

    Conlon, T.; Hamzawi, E.; Campbell, V.

    1998-07-01

    With the support of the Inter-American Development Bank, the Global Environment Facility of the World Bank, and the Rockefeller Foundation, the national electric utility in Jamaica (Jamaica Public Service Company) has begun an assessment of the technical, economic, and financial opportunities for achieving demand-side management (DSM) energy savings in the air conditioning and refrigeration end uses. The feasibility and cost effectiveness of specific measures is being assessed for both the residential and commercials segments. While structures as a traditional load-research-based market assessment, the project uses ethnographic data collection and analysis techniques and involves collaboration with local contractors. The skills of local experts are being taped to identify and interview the key market players, and to develop an understanding of the barriers to and opportunities for energy efficiency present in the evolving equipment markets. The paper outlines methods and presents preliminary case study results for the air conditioning market. The authors identify major groups of market players and dominant types of equipment, and provide an overview of market dynamics. The volume of sales passing through both formal and informal distribution channels is estimated and market barriers are identified. Based on the findings of the study, recommendations will be made for future program and policy initiatives designed to mitigate selected barriers in each of the supply chains.

  10. Energy savings: persuasion and persistence

    Energy Technology Data Exchange (ETDEWEB)

    Eijadi, David; McDougall, Tom; Leaf, Kris; Douglas, Jim; Steinbock, Jason; Reimer, Paul [The Weidt Group, Minnetonka, MN (United States); Gauthier, Julia [Xcel Energy, Minneapolis, MN (United States); Wild, Doug; Richards McDaniel, Stephanie [BWBR Architects, Inc., Saint Paul, MN (United States)

    2005-07-01

    In this study, the architects, sponsoring utility and energy simulation specialist joined together to investigate the persistence of energy savings in three completed projects: a college library; a municipal transportation facility; and a hospital. The primary question being 'How well did the design decisions made with the help of simulation analysis translate into building operations over several years?' Design simulation and metered performance data are compared for specific energy-saving strategies. The paper provides a brief overview of the basis of selection of the three projects, the energy design assistance methods employed and the decisions made, along with their savings expectations. For each case, design characteristics, modelling assumptions, selected strategies and actual metered performance are outlined. We find evidence of appropriate levels of energy conservation, but they are not the absolute values predicted. In each case, the discrepancies between modelling assumptions and final construction or operating procedures are identified, examined and rectified. The paper illustrates that while owners are saving energy, they are not always getting the full savings potential for what they install. The paper concludes with a re-examination of the overall process. It evaluates the potential for additional savings of individual technologies and related larger utility incentives to design teams and building owners.

  11. Saving-Based Asset Pricing

    DEFF Research Database (Denmark)

    Dreyer, Johannes Kabderian; Schneider, Johannes; T. Smith, William

    2013-01-01

    This paper explores the implications of a novel class of preferences for the behavior of asset prices. Following a suggestion by Marshall (1920), we entertain the possibility that people derive utility not only from consumption, but also from the very act of saving. These ‘‘saving-based’’ prefere...

  12. Increasing economic benefits by load-shifting of electrical heat pumps

    OpenAIRE

    Laveyne, Joannes; Zwaenepoel, Brecht; Van Eetvelde, Greet; Vandevelde, Lieven

    2014-01-01

    Electrical heating is still widely used in the process industry. While the use of immersion heaters for the production of hot water or steam is declining, the adoption rate of electrical heat pumps is increasing rapidly. Heat pumps show great flexibility and potential for energy savings, e.g. through low temperature waste heat recuperation. In combination with thermal storage they also allow for load shifting. Because their main power source is electricity, which up to now cannot be stored ef...

  13. Dynamics of electricity efficiency in commercial air-distribution systems in Sweden

    Energy Technology Data Exchange (ETDEWEB)

    Christiansson, Lena

    1996-04-01

    This paper illustrates the long-term potential for reducing future electricity demand for air-distribution in commercial buildings in Sweden. The objective has been to develop a general quantitative scenario-based framework to describe some possible paths for electricity demand for air distribution and to analyze how governmental and utility-sponsored policy measures can affect electricity demand. The focus is on improved electricity efficiency, i.e. a reduction of electricity demand for the same level of services. The results suggest that higher electricity prices will not be very effective in reducing electricity demand, whereas significant electricity savings can be reached by implementing various policy programs, particularly standards. 56 refs, 4 figs, 5 tabs

  14. Freshwater savings from marine protein consumption

    International Nuclear Information System (INIS)

    Gephart, Jessica A; Pace, Michael L; D’Odorico, Paolo

    2014-01-01

    Marine fisheries provide an essential source of protein for many people around the world. Unlike alternative terrestrial sources of protein, marine fish production requires little to no freshwater inputs. Consuming marine fish protein instead of terrestrial protein therefore represents freshwater savings (equivalent to an avoided water cost) and contributes to a low water footprint diet. These water savings are realized by the producers of alternative protein sources, rather than the consumers of marine protein. This study quantifies freshwater savings from marine fish consumption around the world by estimating the water footprint of replacing marine fish with terrestrial protein based on current consumption patterns. An estimated 7 600 km 3  yr −1 of water is used for human food production. Replacing marine protein with terrestrial protein would require an additional 350 km 3  yr −1 of water, meaning that marine protein provides current water savings of 4.6%. The importance of these freshwater savings is highly uneven around the globe, with savings ranging from as little as 0 to as much as 50%. The largest savings as a per cent of current water footprints occur in Asia, Oceania, and several coastal African nations. The greatest national water savings from marine fish protein occur in Southeast Asia and the United States. As the human population increases, future water savings from marine fish consumption will be increasingly important to food and water security and depend on sustainable harvest of capture fisheries and low water footprint growth of marine aquaculture. (paper)

  15. Regularization of DT-MRI Using 3D Median Filtering Methods

    Directory of Open Access Journals (Sweden)

    Soondong Kwon

    2014-01-01

    Full Text Available DT-MRI (diffusion tensor magnetic resonance imaging tractography is a method to determine the architecture of axonal fibers in the central nervous system by computing the direction of the principal eigenvectors obtained from tensor matrix, which is different from the conventional isotropic MRI. Tractography based on DT-MRI is known to need many computations and is highly sensitive to noise. Hence, adequate regularization methods, such as image processing techniques, are in demand. Among many regularization methods we are interested in the median filtering method. In this paper, we extended two-dimensional median filters already developed to three-dimensional median filters. We compared four median filtering methods which are two-dimensional simple median method (SM2D, two-dimensional successive Fermat method (SF2D, three-dimensional simple median method (SM3D, and three-dimensional successive Fermat method (SF3D. Three kinds of synthetic data with different altitude angles from axial slices and one kind of human data from MR scanner are considered for numerical implementation by the four filtering methods.

  16. Safety performance evaluation of cable median barriers on freeways in Florida.

    Science.gov (United States)

    Alluri, Priyanka; Haleem, Kirolos; Gan, Albert; Mauthner, John

    2016-07-03

    This article aims to evaluate the safety performance of cable median barriers on freeways in Florida. The safety performance evaluation was based on the percentages of barrier and median crossovers by vehicle type, crash severity, and cable median barrier type (Trinity Cable Safety System [CASS] and Gibraltar system). Twenty-three locations with cable median barriers totaling about 101 miles were identified. Police reports of 6,524 crashes from years 2005-2010 at these locations were reviewed to verify and obtain detailed crash information. A total of 549 crashes were determined to be barrier related (i.e., crashes involving vehicles hitting the cable median barrier) and were reviewed in further detail to identify crossover crashes and the manner in which the vehicles crossed the barriers; that is, by either overriding, underriding, or penetrating the barriers. Overall, 2.6% of vehicles that hit the cable median barrier crossed the median and traversed into the opposite travel lane. Overall, 98.1% of cars and 95.5% of light trucks that hit the barrier were prevented from crossing the median. In other words, 1.9% of cars and 4.5% of light trucks that hit the barrier had crossed the median and encroached on the opposite travel lanes. There is no significant difference in the performance of cable median barrier for cars versus light trucks in terms of crossover crashes. In terms of severity, overrides were more severe compared to underrides and penetrations. The statistics showed that the CASS and Gibraltar systems performed similarly in terms of crossover crashes. However, the Gibraltar system experienced a higher proportion of penetrations compared to the CASS system. The CASS system resulted in a slightly higher percentage of moderate and minor injury crashes compared to the Gibraltar system. Cable median barriers are successful in preventing median crossover crashes; 97.4% of the cable median barrier crashes were prevented from crossing over the median. Of all of

  17. Performance evaluation of cable median barrier systems in Texas.

    Science.gov (United States)

    2009-08-01

    Since 2003, the Texas Department of Transportation (TxDOT) has embarked on an aggressive campaign to install : median barriers to prevent cross-median crashes on freeway facilities statewide. In the few years prior to 2003, : virtually all fatalities...

  18. Energy savings potential from improved building controls for the US commercial building sector

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, Nick; Katipamula, Srinivas; Wang, Weimin; Xie, Yulong; Zhao, Mingjie

    2017-09-27

    %; seven of the nine building types were in the range of 23 to 29% and two exceeded 40%. The total potential national site savings in for each building type ranged between 95x106 GJ (0.09 Quadrillion British thermal units [Quads]; Large Hotels) to 222x106 GJ (0.21 Quads; Large Office, Hospital Administrative areas, and College/University), resulting in total site savings of 1,393x106 GJ (1.32 Quads) when the three packages are applied to the U.S. commercial buildings stock. Using the source (or primary) energy conversion factors of 1.05 for natural gas and 3.14 for electricity resulted in an approximate potential primary energy savings of 2,912x106 GJ (2.76 Quads), which would be 15% of the sector’s 2015 use of approximately 18,991x106 GJ (18 Quads). Extrapolating the results for other building types not analyzed as part of this study, the primary energy savings could be in the range of 4,220x106 GJ to 5,275x106 GJ (4 to 5 Quads). If this savings potential is realized, it would be equivalent to not combusting 180 to 230 million tons of coal or reducing the energy impacts, at today’s energy intensities, of the per capita consumption of 12 to 15 million people in the U.S. To realize most of this potential savings, many gaps can be addressed through RD&D, as recommended in this paper.

  19. Improved methods to evaluate realised energy savings

    NARCIS (Netherlands)

    Boonekamp, P.G.M.

    2005-01-01

    This thesis regards the calculation of realised energy savings at national and sectoral level, and the policy contribution to total savings. It is observed that the results of monitoring and evaluation studies on realised energy savings are hardly applied in energy saving policy. Causes are the lack

  20. 49 CFR 173.219 - Life-saving appliances.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Life-saving appliances. 173.219 Section 173.219... Life-saving appliances. (a) A life-saving appliance, self-inflating or non-self-inflating, containing small quantities of hazardous materials that are required as part of the life-saving appliance must...

  1. Reducing Carbon Dioxide Emissions from Electricity Sector Using Smart Electric Grid Applications

    Directory of Open Access Journals (Sweden)

    Lamiaa Abdallah

    2013-01-01

    Full Text Available Approximately 40% of global CO2 emissions are emitted from electricity generation through the combustion of fossil fuels to generate heat needed to power steam turbines. Burning these fuels results in the production of carbon dioxide (CO2—the primary heat-trapping, “greenhouse gas” responsible for global warming. Applying smart electric grid technologies can potentially reduce CO2 emissions. Electric grid comprises three major sectors: generation, transmission and distribution grid, and consumption. Smart generation includes the use of renewable energy sources (wind, solar, or hydropower. Smart transmission and distribution relies on optimizing the existing assets of overhead transmission lines, underground cables, transformers, and substations such that minimum generating capacities are required in the future. Smart consumption will depend on the use of more efficient equipment like energy-saving lighting lamps, enabling smart homes and hybrid plug-in electric vehicles technologies. A special interest is given to the Egyptian case study. Main opportunities for Egypt include generating electricity from wind and solar energy sources and its geographical location that makes it a perfect center for interconnecting electrical systems from the Nile basin, North Africa, Gulf, and Europe. Challenges include shortage of investments, absence of political will, aging of transmission and distribution infrastructure, and lack of consumer awareness for power utilization.

  2. Fuel-Cell-Powered Electric Motor Drive Analyzed for a Large Airplane

    Science.gov (United States)

    Brown, Gerald V.; Choi, Benjamin B.

    2005-01-01

    Because of its high efficiency, fuel cell technology may be used to launch a new generation of more-electric aeropropulsion and power systems for future aircraft. Electric-motor-driven airplanes using fuel-cell powerplants would be beneficial to the environment because of fuel savings, low noise, and zero carbon-dioxide emissions. In spite of the fuel cell s efficiency benefit, to produce the same shaft drive power, a fuel cell- powered electric-drive system must be definitely heavier than a turbine-drive system. However, the fuel-cell system s overall efficiency from fuel-to-shaft power is higher than for a turbine-drive system. This means that the fuel consumption rate could be lower than for a conventional system. For heavier, fuel-laden planes for longer flights, we might achieve substantial fuel savings. In the airplane industry, in fact, an efficiency gain of even a few percentage points can make a major economic difference in operating costs.

  3. Velocity trajectory optimization in Hybrid Electric trucks

    NARCIS (Netherlands)

    Keulen, T. van; Jager, B. de; Foster, D.L.; Steinbuch, M.

    2010-01-01

    Hybrid Electric Vehicles (HEVs) enable fuel savings by re-using kinetic and potential energy that was recovered and stored in a battery during braking or driving down hill. Besides, the vehicle itself can be seen as a storage device, where kinetic energy can be stored and retrieved by changing the

  4. Saving in Sub-Saharan Africa

    OpenAIRE

    Ernest Aryeetey; Christopher Udry

    2000-01-01

    Gross domestic savings in Africa averaged only 8 percent of GDP in the 1980s, compared to 23 percent for Southeast Asia and 35 percent in the Newly Industrialized Economies. Aside from being generally low, saving rates in most of Africa have shown consistent decline over the last thirty years. These savings figures must be considered tentative, because they are derived as a residual in the national accounts from expenditure and production data that are themselves quite unreliable. Notwithstan...

  5. Demonstration of energy savings of cool roofs

    Energy Technology Data Exchange (ETDEWEB)

    Konopacki, S.; Gartland, L.; Akbari, H. [Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technologies Div.; Rainer, L. [Davis Energy Group, Davis, CA (United States)

    1998-06-01

    Dark roofs raise the summertime air-conditioning demand of buildings. For highly-absorptive roofs, the difference between the surface and ambient air temperatures can be as high as 90 F, while for highly-reflective roofs with similar insulative properties, the difference is only about 20 F. For this reason, cool roofs are effective in reducing cooling energy use. Several experiments on individual residential buildings in California and Florida show that coating roofs white reduces summertime average daily air-conditioning electricity use from 2--63%. This demonstration project was carried out to address some of the practical issues regarding the implementation of reflective roofs in a few commercial buildings. The authors monitored air-conditioning electricity use, roof surface temperature, plenum, indoor, and outdoor air temperatures, and other environmental variables in three buildings in California: two medical office buildings in Gilroy and Davis and a retail store in San Jose. Coating the roofs of these buildings with a reflective coating increased the roof albedo from an average of 0.20--0.60. The roof surface temperature on hot sunny summer afternoons fell from 175 F--120 F after the coating was applied. Summertime average daily air-conditioning electricity use was reduced by 18% (6.3 kWh/1000ft{sup 2}) in the Davis building, 13% (3.6 kWh/1000ft{sup 2}) in the Gilroy building, and 2% (0.4 kWh/1000ft{sup 2}) in the San Jose store. In each building, a kiosk was installed to display information from the project in order to educate and inform the general public about the environmental and energy-saving benefits of cool roofs. They were designed to explain cool-roof coating theory and to display real-time measurements of weather conditions, roof surface temperature, and air-conditioning electricity use. 55 figs., 15 tabs.

  6. Adolescents and electricity consumption; Investigating sociodemographic, economic, and behavioural influences on electricity consumption in households

    International Nuclear Information System (INIS)

    Wallis, Hannah; Nachreiner, Malte; Matthies, Ellen

    2016-01-01

    With respect to changes in the energy systems of many countries, electricity consumption in households is an important topic. Extensive research has investigated the various determinants of electricity consumption. However, insights into how specific sociodemographic, behavioural, and attitudinal determinants influence residential electricity consumption are still scarce. In this study, we used hierarchical regression analysis to systematically investigate these determinants (including household engagement in electricity saving) along with a wide range of other measures in a sample of German households (N=763). Special attention was given to households with adolescents and children by analysing the influence of the number of adolescents on electricity consumption in a path model. Our results indicate that sociodemographic influences can be explained by the purchasing and use behaviours of residents. Our findings also suggest that the use of behavioural information provides a more detailed picture of the conditions of electricity consumption and thus allows for more appropriate policy planning. - Highlights: •We examined causal drivers of sociodemographic influences on electricity consumption •Sociodemographic influences can be explained by behaviour •Influence of adolescents is mediated by their purchases of IT appliances •It is necessary to also use behavioural information for policy planning

  7. Annual Energy Usage Reduction and Cost Savings of a School: End-Use Energy Analysis

    Science.gov (United States)

    Alghoul, M. A.; Bakhtyar, B.; Asim, Nilofar; Sopian, K.

    2014-01-01

    Buildings are among the largest consumers of energy. Part of the energy is wasted due to the habits of users and equipment conditions. A solution to this problem is efficient energy usage. To this end, an energy audit can be conducted to assess the energy efficiency. This study aims to analyze the energy usage of a primary school and identify the potential energy reductions and cost savings. A preliminary audit was conducted, and several energy conservation measures were proposed. The energy conservation measures, with reference to the MS1525:2007 standard, were modelled to identify the potential energy reduction and cost savings. It was found that the school's usage of electricity exceeded its need, incurring an excess expenditure of RM 2947.42. From the lighting system alone, it was found that there is a potential energy reduction of 5489.06 kWh, which gives a cost saving of RM 2282.52 via the improvement of lighting system design and its operating hours. Overall, it was found that there is a potential energy reduction and cost saving of 20.7% when the energy conservation measures are earnestly implemented. The previous energy intensity of the school was found to be 50.6 kWh/m2/year, but can theoretically be reduced to 40.19 kWh/mm2/year. PMID:25485294

  8. Study of recurrent branch of median nerve (Thenar's muscular branch in relation to the flexor retinaculum and median in 64 hands (32 Men

    Directory of Open Access Journals (Sweden)

    Amirsadri R

    1998-07-01

    Full Text Available Variation of recurred branch of median nerve in relation to the median and flexor retinaculum are significant for both hand surgeons and specialists always. In this study, 64 cadaver hands (32 men have been dissected. The median nerve was identified at the proximal edge of the flexor retinaculum, and in order to expose carpal tunnel the ligament was divided, and the above subjects were studied. The results are: 1 The relation of recurrent nerve to the flexor retinaculum was classified into 4 types: A In (53.1% of subjects, this branch arises from the median after the flexor retinaculum. B In (31.3% of subjects, it arises from the median in the carpal tunnel and the moves around the lower edge of flexor retinaculum and enters the thenar region. C In (14.1% of subjects, it arises from the median in the carpal tunnel and pierces the flexor retinaculum. D In (1.56% of subjects it arises, in the carpal tunnel and it divides into two subbranches here. One follows pattern A and the other pattern C. 2 In this step, the relation of the recurrent branch to the median nerve was studied. The results show that inspite of this image even though most often the recurrent branch arises from the lateral side of median, in (68.75% of subjects it arises from it's anterior surface. The MC Nemar test reveals that there is no relation between manifestation of mentioned patterns with right or left hands.

  9. Modelling energy savings in the Danish building sector combined with internalisation of health related externalities in a heat and power system optimisation model

    International Nuclear Information System (INIS)

    Zvingilaite, Erika

    2013-01-01

    A substantial untapped energy saving potential rests in the building sector and is expected to play an important role in achieving reduction of environmental impacts of energy. In order to utilise this potential, effective policy measures need to be adopted to remove the existing barriers and create incentives. For that purpose, the cost effective energy saving options together with an optimal level of savings and expected environmental benefits have to be identified. The paper reports on a study that analyses these questions by including heat-saving measures in buildings into an energy system optimisation model of the Danish heat and power sector. The achieved optimal level of heat savings reaches 11% of projected heat demand in 2025 under the model assumptions. Moreover, the analysis reveals the importance of considering energy conservation options in a system wide perspective. Furthermore, the results suggest that changes in the energy generation sector are the prime driver behind the reduction of environmental externalities of energy. Heat savings in buildings play only a small role under model assumptions. - Highlights: ► Heat savings in buildings are analysed together with a heat and power system. ► Heat savings compete with electricity to heat technologies, mainly heat pumps. ► Cost effective heat-savings bring small decrease in health impacts and CO 2 emissions. ► Cost-effectiveness of heat savings depends on the marginal heat generation technology

  10. Metaldyne. Plant-Wide Assessment at Royal Oak Finds Opportunities to Improve Manufacturing Effciency, Reduce Energy Use, and Achieve Sigificant Cost Savings

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2005-05-01

    This case study prepared for the U.S. Department of Energy's Industrial Technologies Program describes a plant-wide energy assessment conducted at the Metaldyne, Inc., forging plant in Royal Oak, Michigan. The assessment focused on reducing the plant's operating costs, inventory, and energy use. If the company were to implement all the recommendations that came out of the assessment, its total annual energy savings for electricity would be about 11.5 million kWh and annual cost savings would be $12.6 million.

  11. Metaldyne: Plant-Wide Assessment at Royal Oak Finds Opportunities to Improve Manufacturing Efficiency, Reduce Energy Use, and Achieve Significant Cost Savings

    Energy Technology Data Exchange (ETDEWEB)

    2005-05-01

    This case study prepared for the U.S. Department of Energy's Industrial Technologies Program describes a plant-wide energy assessment conducted at the Metaldyne, Inc., forging plant in Royal Oak, Michigan. The assessment focused on reducing the plant's operating costs, inventory, and energy use. If the company were to implement all the recommendations that came out of the assessment, its total annual energy savings for electricity would be about 11.5 million kWh and annual cost savings would be $12.6 million.

  12. FY 2000 Project report on survey for drawing district energy-saving visions for City of Oguchi; 2000 nendo Oguchi-shi chiiki sho energy vision sakutei nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    The energy-saving visions are drawn for City of Oguchi to help spread the energy-saving practices through the citizens, based on the studies on more efficient and realizable energy-saving measures, including effective utilization of district energy. The energy-saving activities cover the following 6 areas: (1) energy demand trends and current status of energy-saving measures, (2) basic environmental conditions related to energy saving in the district, (3) prediction of energy demands, (4) basic conception of the district energy saving, and introduction methodology, (5) energy-saving implementation plans, and (6) promotion of and problems involved in introduction of the energy-saving measures. The energy-saving implementation plans cover the public facilities, household, schools and private enterprises, and the energy-saving measures studied for the public facilities include introduction of microhydroelectric power generation systems for service water and sewer systems, revolving doors for libraries, high-efficiency illumination systems, and various types of solar systems. Those for household include economic utilization of home electric appliances and automobiles, and those for cooperation by the administration and citizens include thorough separation of garbage. (NEDO)

  13. 24 CFR 221.1 - Savings clause.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Savings clause. 221.1 Section 221.1... MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES LOW COST AND MODERATE INCOME MORTGAGE INSURANCE-SAVINGS CLAUSE Eligibility Requirements-Low Cost Homes-Savings Clause § 221.1...

  14. Energy saving and cost saving cooling; Energie und Kosten sparende Kuehlung

    Energy Technology Data Exchange (ETDEWEB)

    Koenig, Klaus W. [Architektur- und Fachpressebuero Klaus W. Koenig, Ueberlingen (Germany)

    2012-07-01

    In the case of cost reduction, energy conservation and resource savings, rain water is an ideal medium offering more advantages in comparison to the cooling with drinking water. There are no fees for the drinking water and drainage of rain water. It is not necessary to soften rain water so that further operational costs for the treatment and drainage of waste water can be saved. The avoidance of the related material flows and necessary energy is a practiced environmental protection and climate protection.

  15. Electricity demand and conservation potential in the Chinese nonmetallic mineral products industry

    International Nuclear Information System (INIS)

    Lin, Boqiang; Ouyang, Xiaoling

    2014-01-01

    As the high energy-consuming manufacturing industry, electricity consumption of nonmetallic mineral products in China accounted for 7.93% of industrial, 5.84% of national and 1.33% of global electricity consumption in 2010. This study attempts to specify the determinants of sectoral electricity demand, forecast future electricity consumption by creating a model using the Johansen cointegration methodology and estimate the sectoral electricity conservation potential. Results indicate that GDP per capita is the leading force explaining the sectoral electricity consumption increase, while value-added per worker, R and D intensity and electricity price are the main factors contributing to the sectoral electricity consumption decrease. Results demonstrate that sectoral electricity consumption in 2020 will be 369.79–464.83 billion kWh under the low-growth scenario and 530.14–666.39 billion kWh under the high-growth scenario. Moreover, under the low-growth scenario, the sectoral electricity conservation potential in 2020 will be 33.72–95.03 billion kWh, accounting for 0.45–1.26% of China's total electricity demand in 2020; under the high-growth scenario, the sectoral electricity conservation potential in 2020 will be 48.34–136.24 billion kWh, accounting for 0.26–0.74% of world's total electricity consumption in 2010 respectively. Finally, we provide some policy recommendations for encouraging energy conservation in China's nonmetallic mineral products industry. - Highlights: • A long-term relationship of electricity demand in nonmetallic minerals industry is established. • Determinants of the sectoral electricity consumption are specified. • The sectoral electricity demand and saving potential are analyzed using scenarios analysis. • Electricity saving potential will be 48.34–136.24 billion kWh under the high-growth scenario

  16. Marginal cost of electricity conservation: an application of linear program

    International Nuclear Information System (INIS)

    Silveira, A.M. da; Hollanda, J.B. de

    1987-01-01

    This paper is addressed ti the planning of electricity industry when the use of energetically efficient appliances (conservation) is financed by the utilities. It is based on the Linear Programming Model proposed by Masse and Boiteaux for planning of conventional energy sources, where one unity of electricity (Kw/Kw h) saved is treated as if it were a generator of equivalent size. In spite of the formal simplicity of the models it can support interesting concessions on the subject of a electrical energy conservation policy. (author)

  17. Allegheny County Median Age at Death

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The median age at death is calculated for each municipality in Allegheny County. Data is based on the decedent's residence at the time of death, not the location...

  18. A theoretical analysis of the median LMF adaptive algorithm

    DEFF Research Database (Denmark)

    Bysted, Tommy Kristensen; Rusu, C.

    1999-01-01

    Higher order adaptive algorithms are sensitive to impulse interference. In the case of the LMF (Least Mean Fourth), an easy and effective way to reduce this is to median filter the instantaneous gradient of the LMF algorithm. Although previous published simulations have indicated that this reduces...... the speed of convergence, no analytical studies have yet been made to prove this. In order to enhance the usability, this paper presents a convergence and steady-state analysis of the median LMF adaptive algorithm. As expected this proves that the median LMF has a slower convergence and a lower steady...

  19. Electricity Bill

    International Nuclear Information System (INIS)

    Blair, A.; Beith, A.J.; Hardy, P.

    1989-01-01

    The first part of the debate, which lasted a total of about 7 hours, a verbatim report of the first five of which are included here, was about energy conservation. Several new clauses and amendments were discussed. One would place a duty on the new Director of the Energy Supply industry to promote the efficiency and conservation of energy, another would appoint a Deputy Director with responsibility for energy conservation, and the third would require targets of energy efficiency and pollution reduction to be achieved. This allowed discussion on energy saving by domestic thermal insulation, improved efficiency of heating and refrigeration units and on renewable energy sources especially world energy. The second part of the debate was about access to information regarding health and safety resulting from any activities of the electricity supply industry. The remainder of the debate concerned regional representation and the economics of the electricity supply industry. (UK)

  20. How to tackle energy saving and load leveling. Energy saving towards 2000 and measures for the coming winter (energy-saving activities by California`s SCE, demand side management activities); Sho energy fuka heijunka ni do torikumuka. Seireki 2000 nen ni muketa sho energy to konto no shoene taisaku, Kashu SCE no sho energy (DSM katsudo wo saguru)

    Energy Technology Data Exchange (ETDEWEB)

    Nasu, S. [The Energy Conservation Center Japan, Tokyo (Japan)

    1997-02-01

    Tokyo Electric Power has realized a peak shift of 5% for the maximum power demand by various measures to cope with increasing power demand and differential rate by time zone, including expansion of the differential rate system and heat-storage systems. Some of more notable recent techniques are eco-ice and eco-vendor systems, the former storing ice in the heat-storage tanks and the latter strongly cooling vending machines during nighttime. The NAS battery system is being developed as the new technique for load leveling. The energy-related advisory organ for Minister of International Trade and Industry asks each industrial unit to save at least 1% of power on the annual average as the energy-saving measure towards 2000. The energy-saving measures promoted by the government for the coming winter are controlled release of wastes, efficient use of power, setting room temperature at 19{degree}C or lower and voluntarily refrain from commuting by cars. The US power industry is abandoning the concept of DSM in the midst of deregulation and increased competition, and cutting budgets for new energy development. California`s SCE is promoting energy-saving through expanded use of high-efficiency motors, accurate grasp of customers` needs and publicity activities through internet systems. 4 figs., 1 tab.

  1. Electric shocks are ineffective in treatment of lethal effects of rattlesnake envenomation in mice.

    Science.gov (United States)

    Johnson, E K; Kardong, K V; Mackessy, S P

    1987-01-01

    Electrical shocks, even crudely delivered from 'stun guns' and gasoline engine spark plugs, have been reported to be effective in the treatment of snake bite. We thus applied similar electric shocks to mice artificially injected with reconstituted rattlesnake venom at various LD50 multiples. Those envenomated mice treated with electric shock survived no better than the controls. We thus found no evidence that electric shocks crudely administered had any life saving effect in mice.

  2. Cost Analysis of Plug-In Hybred Electric Vehicles Using GPS-Based Longitudinal Travel Data

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Xing [Lamar University; Dong, Jing [Iowa State University; Lin, Zhenhong [ORNL

    2014-01-01

    Using spatial, longitudinal travel data of 415 vehicles over 3 18 months in the Seattle metropolitan area, this paper estimates the operating costs of plug-in hybrid electric vehicles (PHEVs) of various electric ranges (10, 20, 30, and 40 miles) for 3, 5, and 10 years of payback period, considering different charging infrastructure deployment levels and gasoline prices. Some key findings were made. (1) PHEVs could help save around 60% or 40% in energy costs, compared with conventional gasoline vehicles (CGVs) or hybrid electric vehicles (HEVs), respectively. However, for motorists whose daily vehicle miles traveled (DVMT) is significant, HEVs may be even a better choice than PHEV40s, particularly in areas that lack a public charging infrastructure. (2) The incremental battery cost of large-battery PHEVs is difficult to justify based on the incremental savings of PHEVs operating costs unless a subsidy is offered for largebattery PHEVs. (3) When the price of gasoline increases from $4/gallon to $5/gallon, the number of drivers who benefit from a larger battery increases significantly. (4) Although quick chargers can reduce charging time, they contribute little to energy cost savings for PHEVs, as opposed to Level-II chargers.

  3. Small fan assisted air conditioner for thermal comfort and energy saving in Thailand

    International Nuclear Information System (INIS)

    Atthajariyakul, Surat; Lertsatittanakorn, Charoenporn

    2008-01-01

    From the fact that Thai people have a tolerance to high air temperature and are accustomed to high air movement from electric fans in non-air conditioned space, this paper proposes the use of small fan assisted air conditioners for human thermal comfort and energy saving in Thailand. In the study, a total 15 students were tested in a 2.5 x 3.5 x 2.5 m 3 test room equipped with a 12,000 Btu/h split type air conditioner. During the tests, the room air temperature was varied from 25, 26, 27 and 28 deg. C every 1 h. A small fan with 15 cm diameter was placed in front of each subject. In each hour, the small fan was varied to supply a small area with velocity from 0.2, 0.5, 1, 1.5 and 2 m/s. In each condition, the subjects were asked to vote for their thermal sensation. The results showed that the temperature set point could be increased up to 28 deg. C when a small fan was used to supply local air velocity from 0.5 to 2 m/s according to individual preference. This would reduce the electricity consumption of the air conditioning unit. According to the proposed method, this can save energy for office buildings in the commercial sector as high as 1959.51 GWh/year

  4. Distributional impacts of state-level energy efficiency policies in regional electricity markets

    International Nuclear Information System (INIS)

    Sahraei-Ardakani, Mostafa; Blumsack, Seth; Kleit, Andrew

    2012-01-01

    A number of U.S. states have passed legislation targeting energy efficiency and peak demand reduction. We study one such state, Pennsylvania, within the context of PJM, a regional electricity market covering numerous different states. Our focus is on the distributive impacts of this policy—specifically how the policy is likely to impact electricity prices in different areas of Pennsylvania and in the PJM market more generally. Such spatial differences in policy impacts are difficult to model and the transmission system is often ignored in policy studies. Our model estimates supply curves on a “zonal” basis within regional electricity markets and yields information on price and fuel utilization within each zone. We use the zonal supply curves estimated by our model to study regional impacts of energy-efficiency legislation on utilities both inside and outside of Pennsylvania. For most utilities in Pennsylvania, it would reduce the influence of natural gas on electricity price formation and increase the influence of coal. It would also save 2.1 to 2.8 percent of total energy cost in Pennsylvania in a year similar to 2009. The savings are lower than 0.5 percent in other PJM states and the prices may slightly increase in Washington, DC area. - Highlights: ► We model distributional impacts of energy efficiency and conservation policies. ► We use our model to study the impacts of Pennsylvania act 129. ► We estimate $235 million in annual savings for PA and $275 million for PJM. ► The prices decrease in most of the zones but the impacts are not uniform. ► The influence of coal on electricity prices increases relative to natural gas.

  5. The Investigation of Median Frequency Changes in Paraspinal Muscles Following Fatigue

    Directory of Open Access Journals (Sweden)

    Saeed Talebian

    2009-10-01

    Conclusion: Median frequency shift toward low values following fatigue in global and local paraspinal muscles was seen. However, median frequency values for the local stabilizer muscle were higher than median frequency values for the global muscles.

  6. Spread of `Eco-vendor`, an energy-saving type automatic vending machine for beverages with a peak cut function; Shoenegata seiryo inryoyo jido hanbaiki (peak cut kino tsuki) `eko benda` no fukyu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    `Eco-vendor`, an energy-saving type automatic vending machine for beverages with a peak cut function has been developed in 1995 through cooperation by Tokyo Electric Power Company, Coca-Cola Japan, and Fuji Electric Co., Ltd. It can cut 90 percent of the power consumption during 13:00 to 16:00 on weekdays in summer, and can save 10 to 15 percent of annual power consumption. Since the heat insulation performance has been improved to keep beverages at the set temperature during the peak cut operation, the energy-saving effect for cold products in summer and for hot products in winter has been enhanced. For the manufacturing of `Eco-vendor`, Fuji Electric Co., Ltd. has offered its technical know-how to five manufacturers of automatic vending machine for beverages without compensation, and each manufacturer has accepted the offer. Electric power companies of Japan have cooperated to pay incident of 10,000 yen per an `Eco-vendor` to the manufacturers. Japan`s automatic vending machine industries and nationwide beverage industries have positively cooperated. Consequently, Tokyo Electric Power Company has successfully spread 2,600 machines up to the end of fiscal 1995, and aims at the spread of 16,000 machines in fiscal 1996. 2 figs.

  7. System Dynamics Modeling of Households' Electricity Consumption and Cost-Income Ratio: a Case Study of Latvia

    Science.gov (United States)

    Bariss, Uldis; Bazbauers, Gatis; Blumberga, Andra; Blumberga, Dagnija

    2017-11-01

    Increased energy efficiency of the building sector is high on the list of priorities for energy policy since better energy efficiency would help to reduce impact on climate change and increase security of energy supply. One aim of the present study was to find a relative effect of growth of demand for energy services due to changes in income, energy consumption per unit of demand due to technological development, changes in electricity price and household income on household electricity consumption in Latvia. The method applied included system dynamics modeling and data from a household survey regarding the relationship between electricity saving activities and the electricity cost-income ratio. The results revealed that, in direct contrast to the expected, a potential reduction of the electricity consumption is rather insensitive to electricity price and electricity cost-income ratio, and that the efficiency of technologies could be the main drivers for future electricity savings. The results suggest that support to advancement of technologies and faster replacement of inefficient ones rather than influencing the energy price could be effective energy policy measures. The model, developed in the study could be used in similar assessments in other countries.

  8. Intraneural synovial sarcoma of the median nerve

    Directory of Open Access Journals (Sweden)

    Rahul Kasukurthi

    2010-06-01

    Full Text Available Synovial sarcomas are soft-tissue malignancies with a poor prognosis and propensity for distant metastases. Although originally believed to arise from the synovium, these tumors have been found to occur anywhere in the body. We report a rare case of synovial sarcoma arising from the median nerve. To our knowledge, this is the twelfth reported case of intraneural synovial sarcoma, and only the fourth arising from the median nerve. Because the diagnosis may not be apparent until after pathological examination of the surgical speci­men, synovial sarcoma should be kept in mind when dealing with what may seem like a benign nerve tumor.

  9. A road to more and cheaper energy conservation. Evaluation of all the Danish energy saving activities. Appendix; En vej til flere og billigere energibesparelser. En evaluering af samtlige danske energispareaktiviteter. Billagsrapport

    Energy Technology Data Exchange (ETDEWEB)

    2008-12-15

    The appendix together with the main report constitutes the result of the evaluation carried out in 2008 of all Danish energy conservation activities and incentives. A brief introduction is given to the social context of the effort to promote energy conservation and the use of incentives. The main part of the appendix is a presentation of each of the present nine main incentives and activities, their effects and cost. The nine energy saving activities and incentives are: Taxes and CO{sub 2} quotas, the electric utilities' activities, energy labelling of buildings, the Electric Power Saving Trust, building codes, labelling of appliances, energy conservation requirements for public workplaces, agreement with the energy intensive industry, and the Energy Conservation Fund. Finally, the achieved effects of the present Danish energy saving efforts are presented. (ln)

  10. Variable flow controls of closed system pumps for energy savings in maritime power systems

    DEFF Research Database (Denmark)

    Su, Chun-Lien; Liao, Chi-Hsiang; Chou, Tso-Chu

    2016-01-01

    and field tests of a practical auxiliary boiler feed water management system on a commercial vessel. It is proved that the proposed method can maintain constant water pressure for closed system pumps and provide an efficient way to measure energy savings and maintenance benefits. The results serve......Pumps are extensively used in maritime industries as marine vessels utilize a wide range of pumps and pumping techniques to transfer and distribute all types of air and fluids. The electrical energy consumed by the various motors accounts for about 70% of a vessel’s total power consumption......, and this presents a problem in unique marine environments. Such situations are especially conducive to energy-saving strategies using variable frequency drives (VFDs) in centrifugal load service. This paper presents the design and results of applying variable frequency constant pressure technology in closed system...

  11. 'Nurture the sprouting bud; do not uproot it'. Using saving groups to save for maternal and newborn health: lessons from rural Eastern Uganda.

    Science.gov (United States)

    Ekirapa-Kiracho, Elizabeth; Paina, Ligia; Muhumuza Kananura, Rornald; Mutebi, Aloysius; Jane, Pacuto; Tumuhairwe, Juliet; Tetui, Moses; Kiwanuka, Suzanne N

    2017-08-01

    Saving groups are increasingly being used to save in many developing countries. However, there is limited literature about how they can be exploited to improve maternal and newborn health. This paper describes saving practices, factors that encourage and constrain saving with saving groups, and lessons learnt while supporting communities to save through saving groups. This qualitative study was done in three districts in Eastern Uganda. Saving groups were identified and provided with support to enhance members' access to maternal and newborn health. Fifteen focus group discussions (FGDs) and 18 key informant interviews (KIIs) were conducted to elicit members' views about saving practices. Document review was undertaken to identify key lessons for supporting saving groups. Qualitative data are presented thematically. Awareness of the importance of saving, safe custody of money saved, flexible saving arrangements and easy access to loans for personal needs including transport during obstetric emergencies increased willingness to save with saving groups. Saving groups therefore provided a safety net for the poor during emergencies. Poor management of saving groups and detrimental economic practices like gambling constrained saving. Efficient running of saving groups requires that they have a clear management structure, which is legally registered with relevant authorities and that it is governed by a constitution. Saving groups were considered a useful form of saving that enabled easy acess to cash for birth preparedness and transportation during emergencies. They are like 'a sprouting bud that needs to be nurtured rather than uprooted', as they appear to have the potential to act as a safety net for poor communities that have no health insurance. Local governments should therefore strengthen the management capacity of saving groups so as to ensure their efficient running through partnerships with non-governmental organizations that can provide support to such groups.

  12. Federal Aviation Administration retained savings program proposal

    International Nuclear Information System (INIS)

    Hostick, D.J.; Larson, L.L.; Hostick, C.J.

    1998-03-01

    Federal legislation allows federal agencies to retain up to 50% of the savings associated with implementing energy efficiency and water conservation measures and practices. Given budget pressures to reduce expenditures, the use of retained savings to fund additional projects represents a source of funds outside of the traditional budget cycle. The Southwest Region Federal Aviation Administration (FAA) has tasked Pacific Northwest National Laboratory (PNNL) to develop a model retained savings program for Southwest Region FAA use and as a prototype for consideration by the FAA. PNNL recommends the following steps be taken in developing a Southwest Region FAA retained savings program: Establish a retained savings mechanism. Determine the level at which the retained savings should be consolidated into a fund. The preliminary recommendation is to establish a revolving efficiency loan fund at the regional level. Such a mechanism allows some consolidation of savings to fund larger projects, while maintaining a sense of facility ownership in that the funds will remain within the region

  13. Psychological interventions for energy saving. Development and evaluation of an electricity consumption reduction campaign in an urban development of energy-saving buildings; Energiesparen foerdern durch psychologische Intervention. Entwicklung und Evaluation einer Stromsparkampagne in einer Energiesparhaussiedlung

    Energy Technology Data Exchange (ETDEWEB)

    Mack, B.

    2007-07-01

    The study analyzes models of action of social psychology - in particular also an approach to institutionalize routine behaviour patterns - in order to identify the influencing factors that are described and the strategies for energy saving which are promoted. It also presents a comprehensive outline of current intervention studies and identifies effective strategy combinations which may serve as a basis for effective energy conservation campaigns. Against this background, an intervention measure for a neighbourhood context is developed and evaluated which is to promote energy-saving patterns of energy use in private households. The long-term effects suggest that it is a promising strategy to use a combination of information, commitment, goal identification, and individual and comparative feedback and to make use of group processes in a social context for developing energy-saving (routine) behaviour patterns. (orig.)

  14. Values and Technologies in Energy Savings

    DEFF Research Database (Denmark)

    Nørgård, Jørgen Stig

    2000-01-01

    of this saving can cause what is called the rebound effect, which reduces the savings obtained from the technology. Ways to avoid this effect are suggested, and they require value changes, primarly around frugality, consumption, and hard-working. There are indications that some of the necessary changes are well......The chapter is based on the assumption, that technology improvement is not sufficient to achieve a sustainable world community. Changes in people´s values are necessary. A simple model suggest how values, together with basic needs and with the environmental and societal frames, determine people......´s behavioural pattern and lifestyles. Deliberate changes in social values are illustrated by a historical example. From the side of technology the basic principles in the economy of energy savings are briefly described. The marginally profitable energy savings provides an economic saving. The application...

  15. Consumption, price asymmetries, transmission congestion and market power in the Norwegian electricity market

    Energy Technology Data Exchange (ETDEWEB)

    Mirza, Faisal Mehmood

    2011-07-01

    The results from this dissertation add to the ongoing debate in Norway if NordPool spot should shift from zonal price scheme to the nodal price scheme. Academically, the individual papers provide a number of theoretical frameworks that are helpful in analyzing electricity markets around the world. The PhD dissertation investigates price determination process in the Norwegian electricity market and evaluates if the market works at perfectly competitive level or producers exercise market power to drive prices away from their marginal cost of production. Using aggregate hourly electricity supply and demand data, the empirical analysis carried out in this dissertation leads to the following conclusions. 1. Market power at the generation level is not a major problem for the Norwegian electricity market. On average, when we consider the events of binding transmission capacity as exogenous, the average markup in economic terms is small and has not exceeded one percent. 2. Producers can use the information on available transmission capacity between different price areas in Norway and restrict their output to induce transmission congestion in their price area to exercise market power. Average markup during such instances has remained high at 20 percent. 3. Transmission capacity in Norway is not being optimally utilized as import capacity remains at its lowest level during the hours when southern Norway is generally a net importer of electricity, when compared to the rest of the hours of the day. 4. A segment of electricity retailers in the Norwegian electricity market exercises its market power by controlling the pass-through of price changes in the wholesale market to the retail market for variable price contract consumers. The pass-through is asymmetric, whereby cost increase is transmitted completely and quickly when compared to the case of cost decrease. 5.The Daylight saving time (Summer time) policy is helpful in ensuring energy efficiency. It results in electricity

  16. Creating an Eco-village: saving a forest and improving livelihood

    Energy Technology Data Exchange (ETDEWEB)

    Babar, Mohiuddin [Nature Alliance, Dhaka (Bangladesh)

    2012-11-01

    The critical part was to save the forest. Each family uses about 4 to 5 kilogram of firewood. It was found that each tree produced about 140 to 150 kilogram of firewood. Thus, every day two trees were needed to be cut to meet the villagers' need of firewood. In this way, much of the forest would vanish as it did in the past. Nature Alliance took up a project to save the forest. To do it, the primary need was to bring about a change in the habit of the villagers in using firewood. So, a project was taken up for turning Shamalia into an ecovillage. The first step was to motivate the people against cutting trees. However, they needed the wood for use in the kitchen and there was no alternative like natural gas or dependable electricity. Besides starting a massive tree plantation campaign, some households were motivated to set up poultry farm. The venture would in one way give eggs and poultry bird for sale while it would render poultry droppings as feed for producing biogas which could be used as energy for cooking.

  17. Energy-Saving Tunnel Illumination System Based on LED's Intelligent Control

    International Nuclear Information System (INIS)

    Guo Shanshan; Wu Lan; Gu Hanting; Jiang Shuixiu

    2011-01-01

    At present there is a lot of electric energy wastage in tunnel illumination, whose design is based on the maximum brightness outside and the maximum vehicle speed all year round. LED's energy consumption is low, and the control of its brightness is simple and effective. It can be quickly adjusted between 0-100% of its maximum brightness, and will not affect the service life. Therefore, using LED as tunnel's illumination source, we can achieve a good energy saving effect. According to real-time data acquisition of vehicle speed, traffic flow and brightness outside the tunnel, the auto real-time control of tunnel illumination can be achieved. And the system regulated the LED luminance by means of combination of LED power module and intelligent control module. The tunnel information was detected by inspection equipments, which included luminometer, vehicle detector, and received by RTU(Remote Terminal Unit), then synchronously transmitted to PC. After data processing, RTU emitted the dimming signal to the LED driver to adjust the brightness of LED. Despite the relatively high cost of high-power LED lights, the enormous energy-saving effect and the well-behaved controllability is beyond compare to other lighting devices.

  18. Avoiding adverse employment effects from electricity taxation in Norway: What does it cost?

    International Nuclear Information System (INIS)

    Bjertnaes, Geir H.

    2011-01-01

    Welfare analyses of energy taxes typically show that systems with uniform rates perform better than differentiated systems. However, most western countries include some exemptions for their energy-intensive export industries and thereby avoid this potential welfare gain. find that uniform taxation of carbon emissions in combination with a wage subsidy preserves jobs in these industries at a lower welfare cost compared with a differentiated system. The wage subsidy scheme generates a substantial welfare gain per job saved. This study, however, finds that welfare costs are substantial when less accurate policy measures, represented by production-dependent subsidies, protect jobs in Norwegian electricity-intensive industries. The welfare cost per job preserved by this subsidy scheme amounts to approximately 60% of the wage cost per job, suggesting that these jobs are expensive to preserve. A uniform electricity tax combined with production-dependent subsidies preserves jobs at a lower welfare cost compared with the current differentiated electricity tax system. - Highlights: → Avoiding adverse employment effects from electricity taxation is costly in Norway. → Uniform Norwegian electricity tax with job-preserving subsidies improves welfare. → The welfare cost of Norwegian job-saving subsidies amounts to 60% of the wage.

  19. Offshore wind energy storage concept for cost-of-rated-power savings

    International Nuclear Information System (INIS)

    Qin, Chao; Saunders, Gordon; Loth, Eric

    2017-01-01

    Highlights: •Investigated CAES + HPT system concept for offshore wind energy; •Validated cost model for offshore wind farm including CAPEX and OPEX items; •Quantified cost-of-rated-power savings associated with CAES + HPT concept; •Estimated savings of 21.6% with CAES + HPT for a sample $2.92 billion project. -- Abstract: The size and number of off-shore wind turbines over the next decade is expected to rapidly increase due to the high wind energy potential and the ability of such farms to provide utility-scale energy. In this future, inexpensive and efficient on-site wind energy storage can be critical to address short-time (hourly) mismatches between wind supply and energy demand. This study investigates a compressed air energy storage (CAES) and hydraulic power transmission (HPT) system concept. To assess cost impact, the NREL Cost and Scaling Model was modified to improve accuracy and robustness for offshore wind farms with large turbines. Special attention was paid to the support structure, installation, electrical interface and connections, land leasing, and operations and maintenance cost items as well as specific increased/reduced costs reductions associated with CAES + HPT systems. This cost model was validated and applied to a sample $2.92 billion project Virginia Offshore case It was found that adaption of CAES + HPT can lead to a substantial savings of 21.6% of this 20-year lifetime cost by dramatically reducing capital and operating cost of the generator and power transmission components. However, there are several additional variables that can impact the off-shore energy policy and planning for this new CAES + HPT concept. Furthermore, these cost-savings are only first-order estimates based on linear mass-cost relationships, and thus detailed engineering and economic analysis are recommended.

  20. Assessment of energy savings and of side effects associated with consumption cutoffs. Complete report + abridged version

    International Nuclear Information System (INIS)

    2016-03-01

    As France has been the first European country to implement a legal and regulatory framework which acknowledges the role of cut-off operators, and promotes their direct participation to markets, this report aims at preparing an evolution of this framework, notably by focusing on the notion of energy saving. It highlights the importance of definitions regarding levels of consumption deferment and of energy saving associated with consumption cutoffs. The report first analyses the context: assessment of energy savings associated with consumption cutoffs, discussion of the existence or absence of a typical profile of consumption deferment, and definition of a consumption deferment rate, importance of these works for cut-off integration into the electric power system. It proposes a presentation of the present status of knowledge on energy savings and side effects, defines the energy saving rate, and discusses the sensitivity of this rate to calculation parameters. The next part presents the method adopted to analyse results obtained during experiments. The obtained results are then discussed by distinguishing those obtained in the industrial sector, in the tertiary sector, and in the residential sector. Economic studies are then reported regarding the impact of a wrong choice for the deferment rate on market mechanism rules, and the impact of an explicit taking of the deferment into account. Appendices contain detailed presentations of some specific aspects of these assessments and studies. An abridged version of the report is then provided

  1. New electric technologies to reduce global warming impacts

    International Nuclear Information System (INIS)

    Courtright, H.A.

    1994-01-01

    Advanced electric technologies hold significant potential to reduce global warming impact through reduction of primary fuel needed to power end-use applications. These reductions can occur in two forms: (1) reduced kilowatt-hour usage and power plant emissions through efficiency improvements and technological enhancements of existing electrically-driven applications; (2) the development of new electric technologies to replace traditional fossil-fuel driven applications which can result in less overall primary energy consumption and lower overall emissions. Numerous new electric technologies are presently being developed by the Electric Power Research Institute. The technologies reviewed in this paper include: Microwave Fabric Dryer, Advanced Heat Pumps, Heat Pump Water Heater, Infrared Sand Reclaimer, Freeze Concentration, Membrane Water Recovery, Microwave Petrochemical Production, Infrared Drying, and Electric Vehicles. Full commercialization of these technologies can result in significant energy savings and CO 2 reductions, in addition to improving the competitiveness of businesses using these technologies

  2. U.S. electric utility demand-side management 1995

    International Nuclear Information System (INIS)

    1997-01-01

    The US Electric Utility Demand-Side Management report is prepared by the Coal and Electric Data and Renewables Division; Office of Coal, Nuclear, Electric and Alternative Fuels; Energy Information Administration (EIA); US Department of Energy. The report presents comprehensive information on electric power industry demand-side management (DSM) activities in the US at the national, regional, and utility levels. The objective of the publication is to provide industry decision makers, government policy makers, analysts, and the general public with historical data that may be used in understanding DSM as it relates to the US electric power industry. The first chapter, ''Profile: US Electric Utility Demand-Side Management'', presents a general discussion of DSM, its history, current issues, and a review of key statistics for the year. Subsequent chapters present discussions and more detailed data on energy savings, peak load reductions and costs attributable to DSM. 9 figs., 24 tabs

  3. Experimental research of variable rotation speed ICE-based electric power station

    Directory of Open Access Journals (Sweden)

    Dar’enkov Andrey

    2017-01-01

    Full Text Available Developing variable rotation speed ICE-based stand-alone electric power stations which can supply distant regions and autonomous objects with electricity are of scientific interest due to the insufficient study. The relevance of developing such electric power stations is determined by their usage is to provide a significant fuel saving as well as increase ICE motor service life. The article describes the electric station of autonomous objects with improved fuel economy. The article describes multivariate characteristic. Multivariate characteristic shows the optimal frequency of rotation of the internal combustion engine. At this rotational speed there is the greatest fuel economy.

  4. Cold intolerance following median and ulnar nerve injuries : prognosis and predictors

    NARCIS (Netherlands)

    Ruijs, A.C.J; Jaquet, J-B.; van Riel, W. G.; Daanen, H. A M; Hovius, S.E.R.

    This study describes the predictors for cold intolerance and the relationship to sensory recovery after median and ulnar nerve injuries. The study population consisted of 107 patients 2 to 10 years after median, ulnar or combined median and ulnar nerve injuries. Patients were asked to fill out the

  5. Cold intolerance following median and ulnar nerve injuries : prognosis and predictors

    NARCIS (Netherlands)

    Ruijs, A.C.J.; Jaquet, J.B.; Riel, W.G. van; Daanen, H.A.M.; Hovius, S.E.R.

    2007-01-01

    This study describes the predictors for cold intolerance and the relationship to sensory recovery after median and ulnar nerve injuries. The study population consisted of 107 patients 2 to 10 years after median, ulnar or combined median and ulnar nerve injuries. Patients were asked to fill out the

  6. Estimating zonal electricity supply curves in transmission-constrained electricity markets

    International Nuclear Information System (INIS)

    Sahraei-Ardakani, Mostafa; Blumsack, Seth; Kleit, Andrew

    2015-01-01

    Many important electricity policy initiatives would directly affect the operation of electric power networks. This paper develops a method for estimating short-run zonal supply curves in transmission-constrained electricity markets that can be implemented quickly by policy analysts with training in statistical methods and with publicly available data. Our model enables analysis of distributional impacts of policies affecting operation of electric power grid. The method uses fuel prices and zonal electric loads to determine piecewise supply curves, identifying zonal electricity price and marginal fuel. We illustrate our methodology by estimating zonal impacts of Pennsylvania's Act 129, an energy efficiency and conservation policy. For most utilities in Pennsylvania, Act 129 would reduce the influence of natural gas on electricity price formation and increase the influence of coal. The total resulted savings would be around 267 million dollars, 82 percent of which would be enjoyed by the customers in Pennsylvania. We also analyze the impacts of imposing a $35/ton tax on carbon dioxide emissions. Our results show that the policy would increase the average prices in PJM by 47–89 percent under different fuel price scenarios in the short run, and would lead to short-run interfuel substitution between natural gas and coal. - Highlights: • We develop a method to estimate of zonal supply curves in electricity markets. • The model estimates zonal electricity prices and zonal fuel utilization. • The model implicitly captures the average impacts of transmission constraints. • Using the method, we project supply curves for the seventeen utility zones of PJM. • We use the estimated supply curves to study the impacts of Pennsylvania's Act 129 and a carbon tax of $35 per ton

  7. Robust non-local median filter

    Science.gov (United States)

    Matsuoka, Jyohei; Koga, Takanori; Suetake, Noriaki; Uchino, Eiji

    2017-04-01

    This paper describes a novel image filter with superior performance on detail-preserving removal of random-valued impulse noise superimposed on natural gray-scale images. The non-local means filter is in the limelight as a way of Gaussian noise removal with superior performance on detail preservation. By referring the fundamental concept of the non-local means, we had proposed a non-local median filter as a specialized way for random-valued impulse noise removal so far. In the non-local processing, the output of a filter is calculated from pixels in blocks which are similar to the block centered at a pixel of interest. As a result, aggressive noise removal is conducted without destroying the detailed structures in an original image. However, the performance of non-local processing decreases enormously in the case of high noise occurrence probability. A cause of this problem is that the superimposed noise disturbs accurate calculation of the similarity between the blocks. To cope with this problem, we propose an improved non-local median filter which is robust to the high level of corruption by introducing a new similarity measure considering possibility of being the original signal. The effectiveness and validity of the proposed method are verified in a series of experiments using natural gray-scale images.

  8. Distal median nerve dysfunction

    Science.gov (United States)

    ... later on. Inflammation of the tendons ( tendonitis ) or joints ( arthritis ) can also put pressure on the nerve. ... how fast electrical signals move through a nerve Neuromuscular ultrasound to view problems with the muscles and ...

  9. Usefulness of ultrasound assessment of median nerve mobility in carpal tunnel syndrome.

    Science.gov (United States)

    Park, Gi-Young; Kwon, Dong Rak; Seok, Jung Im; Park, Dong-Soon; Cho, Hee Kyung

    2018-01-01

    Background Carpal tunnel syndrome (CTS) is the most common peripheral compression neuropathy of the upper extremity. Recently, dynamic ultrasound (US) imaging has shown differences in median nerve mobility between the affected and unaffected sides in CTS. Purpose The present study was performed to compare the median nerve mobility between patients with CTS and healthy individuals, and to correlate median nerve mobility with the severity of CTS. Material and Methods A total of 101 patients (128 wrists) with CTS and 43 healthy individuals (70 wrists) were evaluated. Electrodiagnostic studies were initially conducted to determine the neurophysiological grading scale (NGS). The cross-sectional area (CSA) of the median nerve and the grade of median nerve mobility were measured using US. Results The mean grade of median nerve mobility in the CTS group (1.9) was significantly lower than that in the control group (2.6; P mobility and distal motor latency of the median nerve (r = -0.218, P = 0.015), NGS (r = -0.207, P = 0.020) and CSA of the median nerve (r = -0.196, P = 0.028). Conclusion The grade of median nerve mobility was negatively correlated with the severity of CTS. US assessment of median nerve mobility may be useful in diagnosing and determining the severity of CTS.

  10. Variable flow controls of closed system pumps for energy savings in maritime power systems

    OpenAIRE

    Su, Chun-Lien; Liao, Chi-Hsiang; Chou, Tso-Chu; Chou, Ming-Hung; Guerrero, Josep M.

    2016-01-01

    Pumps are extensively used in maritime industries as marine vessels utilize a wide range of pumps and pumping techniques to transfer and distribute all types of air and fluids. The electrical energy consumed by the various motors accounts for about 70% of a vessel’s total power consumption, and this presents a problem in unique marine environments. Such situations are especially conducive to energy-saving strategies using variable frequency drives (VFDs) in centrifugal load service. This pape...

  11. Energy savings in Danish residential building stock

    DEFF Research Database (Denmark)

    Tommerup, Henrik M.; Svendsen, Svend

    2006-01-01

    a short account of the technical energy-saving possibilities that are present in existing dwellings and presents a financial methodology used for assessing energy-saving measures. In order to estimate the total savings potential detailed calculations have been performed in a case with two typical...... buildings representing the residential building stock and based on these calculations an assessment of the energy-saving potential is performed. A profitable savings potential of energy used for space heating of about 80% is identified over 45 years (until 2050) within the residential building stock......A large potential for energy savings exists in the Danish residential building stock due to the fact that 75% of the buildings were constructed before 1979 when the first important demands for energy performance of building were introduced. It is also a fact that many buildings in Denmark face...

  12. We Need to Talk... Developing Communicating Power Supplies to Monitor & Control Miscellaneous Electric Loads

    Energy Technology Data Exchange (ETDEWEB)

    Weber, Andrew; Lanzisera, Steven; Liao, Anna; Meier, Alan

    2014-08-11

    Plug loads represent 30percent of total electricity use in residential buildings. Significant energy savings would result from an accurate understanding of which miscellaneous electric devices are using energy, at what time, and in what quantity. Commercially available plug load monitoring and control solutions replace or limit the attached device's native controls - forcing the user to adapt to a separate set of controls associated with the monitoring and control hardware. A better solution is integration of these capabilities at the power supply level. In this paper, we demonstrate a method achieving this integration. Our solution allows unobtrusive power monitoring and control while retaining native device control features. Further, our prototype enables intelligent behaviors by allowing devices to respond to the state of one another automatically. The CPS enables energy savings while demonstrating an added level of functionality to the user. If CPS technology became widespread in devices, a combination of automated and human interactive solutions would enable high levels of energy savings in buildings.

  13. Consumer behaviours: Teaching children to save energy

    Science.gov (United States)

    Grønhøj, Alice

    2016-08-01

    Energy-saving programmes are increasingly targeted at children to encourage household energy conservation. A study involving the assignment of energy-saving interventions to Girl Scouts shows that a child-focused intervention can improve energy-saving behaviours among children and their parents.

  14. Puget Sound area electric reliability plan

    Energy Technology Data Exchange (ETDEWEB)

    1991-09-01

    Various conservation, load management, and fuel switching programs were considered as ways to reduce or shift system peak load. These programs operate at the end-use level, such as residential water heat. Figure D-1a shows what electricity consumption for water heat looks like on normal and extreme peak days. Load management programs, such as water heat control, are designed to reduce electricity consumption at the time of system peak. On the coldest day in average winter, system load peaks near 8:00 a.m. In a winter with extremely cold weather, electricity consumption increases fr all hours, and the system peak shifts to later in the morning. System load shapes in the Puget Sound area are shown in Figure D-1b for a normal winter peak day (February 2, 1988) and extreme peak day (February 3, 1989). Peak savings from any program are calculated to be the reduction in loads on the entire system at the hour of system peak. Peak savings for all programs are measured at 8:00 a.m. on a normal peak day and 9:00 a.m. on an extreme peak day. On extremely cold day, some water heat load shifts to much later in the morning, with less load available for shedding at the time of system peak. Models of hourly end-use consumption were constructed to simulate the impact of conservation, land management, and fuel switching programs on electricity consumption. Javelin, a time-series simulating package for personal computers, was chosen for the hourly analysis. Both a base case and a program case were simulated. 15 figs., 7 tabs.

  15. Electric vehicle charge planning using Economic Model Predictive Control

    DEFF Research Database (Denmark)

    Halvgaard, Rasmus; Poulsen, Niels K.; Madsen, Henrik

    2012-01-01

    Economic Model Predictive Control (MPC) is very well suited for controlling smart energy systems since electricity price and demand forecasts are easily integrated in the controller. Electric vehicles (EVs) are expected to play a large role in the future Smart Grid. They are expected to provide...... grid services, both for peak reduction and for ancillary services, by absorbing short term variations in the electricity production. In this paper the Economic MPC minimizes the cost of electricity consumption for a single EV. Simulations show savings of 50–60% of the electricity costs compared...... to uncontrolled charging from load shifting based on driving pattern predictions. The future energy system in Denmark will most likely be based on renewable energy sources e.g. wind and solar power. These green energy sources introduce stochastic fluctuations in the electricity production. Therefore, energy...

  16. Electrical equipment distributors assuming greater role as suppliers to electric utilities

    International Nuclear Information System (INIS)

    Anon.

    1990-01-01

    A survey was conducted of Canada's largest distributors of electrical equipment to the utility market. Summaries are presented of the views of the major respondents concerning market trends and future challenges. Distributors have emerged as a supply source to utilities over the past two decades. Before then, electric utilities did virtually all their business directly with the manufacturers and rarely with distributors. One reason for this situation was that direct dealing with manufacturers was perceived by the utilites as providing better access to technical advice. Distributors have grown significantly since then and many have their own expert technical staff and provide full support for their products. Various advantages for utilities in dealing with distributors are noted: ability to supply most needs relatively rapidly from stock, simplification of ordering, improved inventory management, and savings in brokerage and other costs associated with imported equipment

  17. The Evaluation of Energy Conservation Performance on Electricity: A Case Study of the TFT-LCD Optronics Industry

    Directory of Open Access Journals (Sweden)

    Ven-Shing Wang

    2016-03-01

    Full Text Available This study describes the performance evaluation of an energy management system, based on electricity consumption, for a Gen 6 Thin Film Transistor Liquid Crystal Display (TFT-LCD panel plant. Of the various production lines and facility systems, the array system and the compressed dry air consumed the most electricity of 21.8% and 19.8%, respectively, while the public utility used only 1.6% of the total electricity. The baseline electricity consumptions were correlated well (R2 ≥ 0.77 to the monthly average wet-bulb temperatures of ambient air and the panel yield rates, which were determined by the product yield over the equipment available time index. After implementing the energy saving projects, the energy conservation performance was determined using a three-parameter change-point regression model incorporated with the panel yield rates. The post-retrofit monthly savings of the total electricity consumption for the panel manufacture were 5.35%–10.36%, with the efficiency of the electricity performance revealing an upswing trend following the implementation of the energy management system.

  18. Accuracy of automated measurement and verification (M&V) techniques for energy savings in commercial buildings

    International Nuclear Information System (INIS)

    Granderson, Jessica; Touzani, Samir; Custodio, Claudine; Sohn, Michael D.; Jump, David; Fernandes, Samuel

    2016-01-01

    by evaluating the accuracy of ten baseline energy use models, against measured data from a large dataset of 537 buildings. The results of this study show that the already available advanced interval data baseline models hold great promise for scaling the adoption of building measured savings calculations using Advanced Metering Infrastructure (AMI) data. Median coefficient of variation of the root mean squared error (CV(RMSE)) was less than 25% for every model tested when twelve months of training data were used. With even six months of training data, median CV(RMSE) for daily energy total was under 25% for all models tested. These findings can be used to build confidence in model robustness, and the readiness of these approaches for industry uptake and adoption.

  19. Supplier choice and WTP for electricity attributes in an emerging market: The role of perceived past experience, environmental concern and energy saving behavior

    International Nuclear Information System (INIS)

    Amador, Francisco Javier; González, Rosa Marina; Ramos-Real, Francisco Javier

    2013-01-01

    This study analyzes customers' preferences and their willingness to pay (WTP) for certain service attributes in an electricity supplier choice context. Specifically, a stated preference choice experiment is conducted in the Canary Islands' residential market where limited competition exists. Preferences for different electricity suppliers and three level-of-service attributes are investigated, namely, supply reliability, share of renewable energies and availability of a complementary energy audit service. The results might be interpreted as an indication of different aspects new firms need to consider if they plan to enter in the market. There is an opportunity for new companies to establish in the market, though evidence of brand loyalty to the current company and/or significant switching costs are also found, especially in the case of older people. Regarding the estimated WTP, several results should be highlighted. First, customers who have experienced more serious outages in the past tend to show a higher WTP to reduce the outage frequency. Second, highly-educated respondents, those who state a great concern for the greenhouse gases (GHG) emissions and those who carry out energy saving actions in their homes exhibit a larger WTP for renewable energies. This empirical evidence provides useful information for authorities responsible for energy policy design. - Highlights: • A stated choice experiment is conducted in the Canary Islands' residential market. • Serious outages in the past lead to a higher WTP to reduce the outage frequency. • A higher education level explains a greater WTP for renewables. • People concerned for emissions and energy savers show greater WTP for renewables. • These findings provide useful information for energy policy design

  20. Comparison of control systems for the optimisation of ice storage in a dynamic real time electricity pricing environment

    International Nuclear Information System (INIS)

    Murphy, M.D.; O’Mahony, M.J.; Upton, J.

    2015-01-01

    Highlights: • A cold thermal energy storage system model was created and validated. • Pseudo real time electricity pricing was derived to represent the smart grid. • A demand side management optimisation algorithm was developed. • Demand side management algorithm performance was compared to a standard controller.