Influence of tyre-road contact model on vehicle vibration response

Science.gov (United States)

Múčka, Peter; Gagnon, Louis

2015-09-01

The influence of the tyre-road contact model on the simulated vertical vibration response was analysed. Three contact models were compared: tyre-road point contact model, moving averaged profile and tyre-enveloping model. In total, 1600 real asphalt concrete and Portland cement concrete longitudinal road profiles were processed. The linear planar model of automobile with 12 degrees of freedom (DOF) was used. Five vibration responses as the measures of ride comfort, ride safety and dynamic load of cargo were investigated. The results were calculated as a function of vibration response, vehicle velocity, road quality and road surface type. The marked differences in the dynamic tyre forces and the negligible differences in the ride comfort quantities were observed among the tyre-road contact models. The seat acceleration response for three contact models and 331 DOF multibody model of the truck semi-trailer was compared with the measured response for a known profile of test section.

Road Service Performance Based On Integrated Road Design Consistency (IC Along Federal Road F0023

Directory of Open Access Journals (Sweden)

Zainal Zaffan Farhana

2017-01-01

Full Text Available Road accidents are one of the world’s largest public health and injury prevention problems. In Malaysia, the west coast area of Malaysia been stated as the highest motorcycle fatalities and road accidents are one of the factors that cause of death and injuries in this country. The most common fatal accident is between a motorcycle and passenger car. The most of the fatal accidents happened on Federal roads with 44 fatal accidents reported, which is equal to 29%. Lacks of road geometric designs consistency where the drivers make mistakes errors due to the road geometric features causes the accident kept rising in Malaysia. Hence, models are based on operating speed to calculate design consistency of road. The profiles were obtained by continuous speed profile using GPS data. The continuous operating speed profile models were plotted based on operating speed model (85th percentile. The study was conduct at F0023 from km 16 until km 20. The purpose of design consistency is to know the relationship between the operating speed and elements of geometric design on the road. As a result, the integrated design consistency motorcycle and cars along a segment at F0023, the threshold shows poor design quality for motorcycles and cars.

Road safety performance indicators : country profiles. SafetyNet, Building the European Road Safety Observatory, Workpackage 3, Deliverable 3.7b.

NARCIS (Netherlands)

Riguelle, F. Eksler, V. Holló, P. Morsink, P. Gent, A. van Gitelman, V. Assum, T. & Rackliff, L.

2009-01-01

The EC 6th Framework Integrated Project SafetyNet aims to accelerate the availability and use of harmonised road safety data in Europe. Having such data available throughout Europe would be tremendously beneficial for road safety, since it would enable the evaluation of road safety measures, the

Road traffic injury on rural roads in Tanzania: measuring the effectiveness of a road safety program.

Science.gov (United States)

Zimmerman, Karen; Jinadasa, Deepani; Maegga, Bertha; Guerrero, Alejandro

2015-01-01

Road traffic injuries (RTIs) are a major public health burden, especially in low- and middle-income countries. There is limited data on RTIs in low-volume, rural African settings. This study attempted to survey all individuals living in households within 200 m of two low-volume rural roads in Tanzania and to collect data on RTIs. Local communities and users of the Bago to Talawanda road (intervention site) and Kikaro to Mihuga road (control site) were targeted and received an intensive program of road safety measures tailored using the crash characteristics of the baseline sample. Demographic data on all household members were collected, and those individuals who suffered an RTI in the previous 3 months had comprehensive information collected about the crash characteristics and the socioeconomic impact. The follow-up data collection occurred nine months after the baseline data were collected. The majority of crashes that caused an RTI involved a motorcycle (71%) and the majority of victims were male (82%) with an average age of 27. Injuries to the legs (55%) were most common and the average length of time away from normal activity was 27 (±33) days. RTI incidence at the intervention site increased during the course of the study (incidence before vs. incidence after) and was unchanged in the community control (incidence before vs. incidence after). The incidence of RTIs in the low-volume rural setting is unacceptably high and most commonly associated with motorcycles. The change in incidence is unreliable due to logistic restraints of the project and more research is needed to quantify the impact of various RTI prevention strategies in this setting. This study provides insight into road traffic injuries on low-volume rural roads, areas where very little research has been captured. Additionally, it provides a replicable study design for those interested in collecting similar data on low-volume rural roads.

3D Tyre/Road pavement contact stress measurements

CSIR Research Space (South Africa)

De Beer, Morris

2010-10-01

Full Text Available The CSIR’s proprietary Stress-in-Motion (SIM) measurements provide rational descriptions of 1D, 2D and 3D tyre/road pavement stresses for: Road pavement design testing and evaluation, as well as tyre design, testing and evaluation....

An instrument for the measurement of road surface reflection properties

DEFF Research Database (Denmark)

Corell, Dennis Dan; Sørensen, K.

2017-01-01

Road surface reflection data in the form of standard r-tables serve as input for design calculations of road lighting installations on traffic roads. However, in several countries the use of the standard r-tables has not been verified by measurement in a long period of time, while the types of road...

An instrument for the measurement of road surface reflection properties

DEFF Research Database (Denmark)

Corell, Dennis Dan; Sørensen, K.

2017-01-01

surfaces in use have changed - for instance to road surface types with less noise from wheel passages. Because of this, a co-operation between the road administrations of the Nordic countries (abbreviated NMF) decided to construct a portable instrument to be used on selections of traffic roads within......Road surface reflection data in the form of standard r-tables serve as input for design calculations of road lighting installations on traffic roads. However, in several countries the use of the standard r-tables has not been verified by measurement in a long period of time, while the types of road...

Testing measurements of airflow velocity in road tunnels

Directory of Open Access Journals (Sweden)

Danišovič Peter

2017-01-01

Full Text Available Within the project entitled “Models of formation and spread of fire to increase safety of road tunnels”, it was necessary to devise a method how to record airflow velocity during the fire in situ tests in road tunnels. Project is in first year of its solution so one testing measurement was performed to check the functionality of anemometers selected for this project and the first in situ measurement was also performed just a few days ago.

Neuro-Fuzzy Prediction of Cooperation Interaction Profile of Flexible Road Train Based on Hybrid Automaton Modeling

Directory of Open Access Journals (Sweden)

Banjanovic-Mehmedovic Lejla

2016-01-01

Full Text Available Accurate prediction of traffic information is important in many applications in relation to Intelligent Transport systems (ITS, since it reduces the uncertainty of future traffic states and improves traffic mobility. There is a lot of research done in the field of traffic information predictions such as speed, flow and travel time. The most important research was done in the domain of cooperative intelligent transport system (C-ITS. The goal of this paper is to introduce the novel cooperation behaviour profile prediction through the example of flexible Road Trains useful road cooperation parameter, which contributes to the improvement of traffic mobility in Intelligent Transportation Systems. This paper presents an approach towards the control and cooperation behaviour modelling of vehicles in the flexible Road Train based on hybrid automaton and neuro-fuzzy (ANFIS prediction of cooperation profile of the flexible Road Train. Hybrid automaton takes into account complex dynamics of each vehicle as well as discrete cooperation approach. The ANFIS is a particular class of the ANN family with attractive estimation and learning potentials. In order to provide statistical analysis, RMSE (root mean square error, coefficient of determination (R2 and Pearson coefficient (r, were utilized. The study results suggest that ANFIS would be an efficient soft computing methodology, which could offer precise predictions of cooperative interactions between vehicles in Road Train, which is useful for prediction mobility in Intelligent Transport systems.

Tyre noise predictions from computed road surface texture induced contact pressure; Romen no outotsu ni kiinsuru sesshoku atsuryoku ni yoru tire soon no suitei

Energy Technology Data Exchange (ETDEWEB)

Mikami, T. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

1999-07-01

A method for tire/road noise prediction is studied based on the result of road surface profile measurement (horizontal direction measurement interval 3mm, horizontal direction measurement accuracy 8{mu}m, distance measured 1655m, using a laser-aided profile meter). The obtained road surface profile is used for the calculation of contact pressure that occurs between the tire tread and road surface (using the 2-dimensional calculation model of Clapp et al.). For the examination of the relationship between the contact pressure and generated noise, tire noise is measured using a microphone array provided near the tire circumference. The frequency spectral ratio between the generated noise and contact pressure is determined as a transmission function. It may be said that the transmission function is unique to the tire, not dependent on the road surface profile. The road surface profile is determined by use of the transmission function, and this enables the prediction of the noise from the tire. Noises were measured on several kinds of road surfaces different in coarseness for a passenger car and truck, and the values from these actual measurements are compared with the predicted values, and then it is found that the prediction model is valid. (NEDO)

Road weather management performance measures : 2012 update.

Science.gov (United States)

2013-08-01

In 2007, the Road Weather Management Program (RWMP) conducted a study with stakeholders from the transportation and meteorological communities to define eleven performance measures that would enable the Federal Highway Administration (FHWA) to determ...

Effects of road mortality and mitigation measures on amphibian populations.

Science.gov (United States)

Beebee, Trevor J C

2013-08-01

Road mortality is a widely recognized but rarely quantified threat to the viability of amphibian populations. The global extent of the problem is substantial and factors affecting the number of animals killed on highways include life-history traits and landscape features. Secondary effects include genetic isolation due to roads acting as barriers to migration. Long-term effects of roads on population dynamics are often severe and mitigation methods include volunteer rescues and under-road tunnels. Despite the development of methods that reduce road kill in specific locations, especially under-road tunnels and culverts, there is scant evidence that such measures will protect populations over the long term. There also seems little likelihood that funding will be forthcoming to ameliorate the problem at the scale necessary to prevent further population declines. © 2013 Society for Conservation Biology.

Problems in determining the optimal use of road safety measures

DEFF Research Database (Denmark)

Elvik, Rune

2014-01-01

for intervention that ensures maximum safety benefits. The third problem is how to develop policy options to minimise the risk of indivisibilities and irreversible choices. The fourth problem is how to account for interaction effects between road safety measures when determining their optimal use. The fifth......This paper discusses some problems in determining the optimal use of road safety measures. The first of these problems is how best to define the baseline option, i.e. what will happen if no new safety measures are introduced. The second problem concerns choice of a method for selection of targets...... problem is how to obtain the best mix of short-term and long-term measures in a safety programme. The sixth problem is how fixed parameters for analysis, including the monetary valuation of road safety, influence the results of analyses. It is concluded that it is at present not possible to determine...

Road salt emissions: A comparison of measurements and modelling using the NORTRIP road dust emission model

Science.gov (United States)

Denby, B. R.; Ketzel, M.; Ellermann, T.; Stojiljkovic, A.; Kupiainen, K.; Niemi, J. V.; Norman, M.; Johansson, C.; Gustafsson, M.; Blomqvist, G.; Janhäll, S.; Sundvor, I.

2016-09-01

De-icing of road surfaces is necessary in many countries during winter to improve vehicle traction. Large amounts of salt, most often sodium chloride, are applied every year. Most of this salt is removed through drainage or traffic spray processes but a certain amount may be suspended, after drying of the road surface, into the air and will contribute to the concentration of particulate matter. Though some measurements of salt concentrations are available near roads, the link between road maintenance salting activities and observed concentrations of salt in ambient air is yet to be quantified. In this study the NORTRIP road dust emission model, which estimates the emissions of both dust and salt from the road surface, is applied at five sites in four Nordic countries for ten separate winter periods where daily mean ambient air measurements of salt concentrations are available. The model is capable of reproducing many of the salt emission episodes, both in time and intensity, but also fails on other occasions. The observed mean concentration of salt in PM10, over all ten datasets, is 4.2 μg/m3 and the modelled mean is 2.8 μg/m3, giving a fractional bias of -0.38. The RMSE of the mean concentrations, over all 10 datasets, is 2.9 μg/m3 with an average R2 of 0.28. The mean concentration of salt is similar to the mean exhaust contribution during the winter periods of 2.6 μg/m3. The contribution of salt to the kerbside winter mean PM10 concentration is estimated to increase by 4.1 ± 3.4 μg/m3 for every kg/m2 of salt applied on the road surface during the winter season. Additional sensitivity studies showed that the accurate logging of salt applications is a prerequisite for predicting salt emissions, as well as good quality data on precipitation. It also highlights the need for more simultaneous measurements of salt loading together with ambient air concentrations to help improve model parameterisations of salt and moisture removal processes.

The in situ measurement of road reflection.

NARCIS (Netherlands)

Schreuder, D.A.

1994-01-01

This paper describes a procedure that has been designed to measure P(0;0), P(2;0) and P(1;90), the three values that are the basis for the C1-C2 system for measuring road reflection of light. The system was proposed in The Netherlands, and subsequently adopted by the CIE as an alternative to the

Aquaplaning : Development of a Risk Pond Model from Road Surface Measurements

OpenAIRE

Nygårdhs, Sara

2003-01-01

Aquaplaning accidents are relatively rare, but could have fatal effects. The task of this master’s thesis is to use data from the Laser Road Surface Tester to detect road sections with risk of aquaplaning. A three-dimensional model based on data from road surface measurements is created using MATLAB (version 6.1). From this general geometrical model of the road, a pond model is produced from which the theoretical risk ponds are detected. A risk pond indication table is fur-ther created. The...

Development in techniques for studying forest roads on peatlands

International Nuclear Information System (INIS)

Saarilahti, M.

1988-01-01

A light seismic method, a short-pulse radar and a microwave probe are tested in assessing the properties of a forest road constructed on peatland. The light seismic method gave reliable values for estimating the bearing capacity of the road. It was found that bearing capacity was mostly dependent on embankment thickness, but quality of labric might also have an influence. Embankment thickness and peat depth can be measured on the radargram, and some additional information on road bed and peat obtained. The microwave peat probe permits recording of the continuous moisture profile in situ, which improves accuracy of planning

Development in techniques for studying forest roads on peatlands

Energy Technology Data Exchange (ETDEWEB)

Saarilahti, M.

1988-07-01

A light seismic method, a short-pulse radar and a microwave probe are tested in assessing the properties of a forest road constructed on peatland. The light seismic method gave reliable values for estimating the bearing capacity of the road. It was found that bearing capacity was mostly dependent on embankment thickness, but quality of labric might also have an influence. Embankment thickness and peat depth can be measured on the radargram, and some additional information on road bed and peat obtained. The microwave peat probe permits recording of the continuous moisture profile in situ, which improves accuracy of planning.

A quantitative approach to measure road network information based on edge diversity

Science.gov (United States)

Wu, Xun; Zhang, Hong; Lan, Tian; Cao, Weiwei; He, Jing

2015-12-01

The measure of map information has been one of the key issues in assessing cartographic quality and map generalization algorithms. It is also important for developing efficient approaches to transfer geospatial information. Road network is the most common linear object in real world. Approximately describe road network information will benefit road map generalization, navigation map production and urban planning. Most of current approaches focused on node diversities and supposed that all the edges are the same, which is inconsistent to real-life condition, and thus show limitations in measuring network information. As real-life traffic flow are directed and of different quantities, the original undirected vector road map was first converted to a directed topographic connectivity map. Then in consideration of preferential attachment in complex network study and rich-club phenomenon in social network, the from and to weights of each edge are assigned. The from weight of a given edge is defined as the connectivity of its end node to the sum of the connectivities of all the neighbors of the from nodes of the edge. After getting the from and to weights of each edge, edge information, node information and the whole network structure information entropies could be obtained based on information theory. The approach has been applied to several 1 square mile road network samples. Results show that information entropies based on edge diversities could successfully describe the structural differences of road networks. This approach is a complementarity to current map information measurements, and can be extended to measure other kinds of geographical objects.

Safety effects of low-cost engineering measures. An observational study in a Portuguese multilane road.

Science.gov (United States)

Vieira Gomes, Sandra; Cardoso, João Lourenço

2012-09-01

Single carriageway multilane roads are not, in general, a very safe type of road, mainly because of the high number of seriously injured victims in head-on collisions, when compared with dual carriageway multilane roads, with a median barrier. In this paper the results of a study on the effect of the application of several low cost engineering measures, aimed at road infrastructure correction and road safety improvement on a multilane road (EN6), are presented. The study was developed by the National Laboratory of Civil Engineering (LNEC) for the Portuguese Road Administration and involved a comparison of selected aspects of motorized traffic behaviour (traffic volumes and speeds) measured in several sections of EN6, as well as monitoring of road safety developments in the same road. The applied low cost engineering measures allowed a reduction of 10% in the expected annual number of personal injury accidents and a 70% decrease in the expected annual number of head-on collisions; the expected annual frequency of accidents involving killed and seriously injured persons was reduced by 26%. Copyright © 2012 Elsevier Ltd. All rights reserved.

Experiences with the implementation of measures and tools for road safety improvement

Energy Technology Data Exchange (ETDEWEB)

Mikusova, M.

2016-07-01

The paper presents an overview on the road safety measures implemented in the framework of the “SOL – Save our lives” project. It contains summarization of general knowledge regarding the efficiency of the measures applied and conclusions from the analyses of developed strategies and action plans, including common issues, strengths and weaknesses of developed tools and puts these in the context of wider European Road Safety strategies. The purpose of the paper is to provide recommendations for an effective professional development of road safety programs at community level in the context of sustainable mobility. (Author)

Road map for selected key measurements from LHCb

CERN Document Server

Adeva, B.; Affolder, A.; Ajaltouni, Z.; Albrecht, J.; Alessio, F.; Alexander, M.; Alvarez Cartelle, P.; Alves, A.A., Jr; Amato, S.; Amhis, Y.; Amoraal, J.; Anderson, J.; Aquines Gutierrez, O.; Arrabito, L.; Artuso, M.; Aslanides, E.; Auriemma, G.; Bachmann, S.; Bagaturia, Y.; Bailey, D.S.; Balagura, V.; Baldini, W.; Pazos, MdC.Barandela; Barlow, R.J.; Barsuk, S.; Bates, A.; Bauer, C.; Bauer, Th.; Bay, A.; Bediaga, I.; Belous, K.; Belyaev, I.; Benayoun, M.; Bencivenni, G.; Bernet, R.; Bettler, M.O.; Bizzeti, A.; Blake, T.; Blanc, F.; Blanks, C.; Blouw, J.; Blusk, S.; Bobrov, A.; Bocci, V.; Bondar, A.; Bondar, N.; Bonivento, W.; Borghi, S.; Borgia, A.; Bos, E.; Bowcock, T.J.V.; Bozzi, C.; Bressieux, J.; Brisbane, S.; Britsch, M.; Brook, N.H.; Brown, H.; Buchler-Germann, A.; Buytaert, J.; Cachemiche, J.P.; Cadeddu, S.; Caicedo Carvajal, J.M.; Callot, O.; Calvi, M.; Calvo Gomez, M.; Camboni, A.; Cameron, W.; Campana, P.; Carbone, A.; Carboni, G.; Cardini, A.; Carson, L.; Carvalho Akiba, K.; Casse, G.; Cattaneo, M.; Charles, M.; Charpentier, Ph.; Chlopik, A.; Ciambrone, P.; Cid Vidal, X.; Clark, P.J.; Clarke, P.E.L.; Clemencic, M.; Cliff, H.V.; Closier, J.; Coca, C.; Coco, V.; Cogan, J.; Collins, P.; Constantin, F.; Conti, G.; Contu, A.; Corti, G.; Cowan, G.A.; D'Almagne, B.; D'Ambrosio, C.; d'Enterria, D.G.; Da Silva, W.; David, P.; De Bonis, I.; De Capua, S.; De Cian, M.; De Lorenzi, F.; De Miranda, J.M.; De Paula, L.; De Simone, P.; De Vries, H.; Decamp, D.; Degaudenzi, H.; Deissenroth, M.; Del Buono, L.; Deplano, C.; Deschamps, O.; Dettori, F.; Dickens, J.; Dijkstra, H.; Dima, M.; Donleavy, S.; Reis, A.C.dos; Dovbnya, A.; Pree, T.Du; Duval, P.Y.; Dwyer, L.; Dzhelyadin, R.; Eames, C.; Easo, S.; Egede, U.; Egorychev, V.; Eisele, F.; Eisenhardt, S.; Eklund, L.; Esperante Pereira, D.; Esteve, L.; Eydelman, S.; Fanchini, E.; Farber, C.; Fardell, G.; Farinelli, C.; Farry, S.; Fave, V.; Fernandez Albor, V.; Ferro-Luzzi, M.; Filippov, S.; Fitzpatrick, C.; Fontanelli, F.; Forty, R.; Frank, M.; Frei, C.; Frosini, M.; Fungueirino Pazos, J.L.; Furcas, S.; Gallas Torreira, A.; Galli, D.; Gandelman, M.; Gao, Y.; Garnier, J-C.; Garrido, L.; Gaspar, C.; Gauvin, N.; Gersabeck, M.; Gershon, T.; Ghez, Ph.; Gibson, V.; Gilitsky, Yu.; Gligorov, V.V.; Gobel, C.; Golubkov, D.; Golutvin, A.; Gomes, A.; Grabalosa Gandara, M.; Graciani Diaz, R.; Granado Cardoso, L.A.; Grauges, E.; Graziani, G.; Grecu, A.; Guerrer, G.; Gushchin, E.; Guz, Yu.; Guzik, Z.; Gys, T.; Hachon, F.; Haefeli, G.; Haines, S.C.; Hampson, T.; Hansmann-Menzemer, S.; Harji, R.; Harnew, N.; Harrison, P.F.; He, J.; Hennessy, K.; Henrard, P.; Hernando Morata, J.A.; Hicheur, A.; Hicks, E.; Hofmann, W.; Holubyev, K.; Hopchev, P.; Hulsbergen, W.; Hunt, P.; Huse, T.; Huston, R.S.; Hutchcroft, D.; Iakovenko, V.; Escudero, C.Iglesias; Imong, J.; Jacobsson, R.; Jahjah Hussein, M.; Jans, E.; Jansen, F.; Jaton, P.; Jean-Marie, B.; John, M.; Jones, C.R.; Jost, B.; Kapusta, F.; Karbach, T.M.; Keaveney, J.; Kerzel, U.; Ketel, T.; Keune, A.; Khalil, S.; Khanji, B.; Kim, Y.M.; Knecht, M.; Knopf, J.; Koblitz, S.; Konoplyannikov, A.; Koppenburg, P.; Korolko, I.; Kozlinskiy, A.; Krasowski, M.; Kravchuk, L.; Krokovny, P.; Kruzelecki, K.; Kucharczyk, M.; Kudryashov, I.; Kvaratskheliya, T.; Lacarrere, D.; Lai, A.; Lambert, R.W.; Lanfranchi, G.; Langenbruch, C.; Latham, T.; Le Gac, R.; Lefevre, R.; Leflat, A.; Lefrancois, J.; Leroy, O.; Lessnoff, K.; Li, L.; Li, Y.Y.; Libby, J.; Lieng, M.; Lindner, R.; Lindsey, S.; Linn, C.; Liu, B.; Liu, G.; Lopes, J.H.; Lopez Asamar, E.; Luisier, J.; Machefert, F.; Machikhiliyan, I.; Maciuc, F.; Maev, O.; Magnin, J.; Maier, A.; Mamunur, R.M.D.; Manca, G.; Mancinelli, G.; Mangiafave, N.; Marconi, U.; Marin, F.; Marks, J.; Martellotti, G.; Martens, A.; Martin, L.; Martinez Santos, D.; Mathe, Z.; Matteuzzi, C.; Matveev, V.; Mazurov, A.; McGregor, G.; Mcharek, B.; Mclean, C.; McNulty, R.; Merk, M.; Merkel, J.; Merkin, M.; Messi, R.; Metlica, F.C.D.; Michalowski, J.; Miglioranzi, S.; Minard, M.N.; Monteil, S.; Moran, D.; Morris, J.V.; Mountain, R.; Mous, I.; Muheim, F.; Muresan, R.; Murtas, F.; Muryn, B.; Musy, M.; Mylroie-Smith, J.; Naik, P.; Nakada, T.; Nandakumar, R.; Nardulli, J.; Natkaniec, Z.; Nedos, M.; Needham, M.; Neufeld, N.; Nicolas, L.; Nies, S.; Niess, V.; Nikitin, N.; Noor, A.; Oblakowska-Mucha, A.; Obraztsov, V.; Oggero, S.; Okhrimenko, O.; Oldeman, R.; Orlandea, M.; Ostankov, A.; Palacios, J.; Palutan, M.; Panman, J.; Papadelis, A.; Papanestis, A.; Pappagallo, M.; Parkes, C.; Passaleva, G.; Patel, G.D.; Patel, M.; Paterson, S.K.; Patrick, G.N.; Pauna, E.; Pauna, C.; Pavel, C.; Pazos Alvarez, A.; Pellegrino, A.; Penso, G.; Pepe Altarelli, M.; Perazzini, S.; Perego, D.L.; Perez-Calero Yzquierdo, A.; Perez Trigo, E.; Perret, P.; Pessina, G.; Petrella, A.; Petrolini, A.; Pietrzyk, B.; Pinci, D.; Playfer, S.; Plo Casasus, M.; Polok, G.; Poluektov, A.; Polycarpo, E.; Popov, D.; Popovici, B.; Poss, S.; Potterat, C.; Powell, A.; Pozzi, S.; Pugatch, V.; Puig Navarro, A.; Qian, W.; Rademacker, J.H.; Rakotomiaramanana, B.; Raniuk, I.; Raven, G.; Redford, S.; Reece, W.; Ricciardi, S.; Rinnert, K.; Robbe, P.; Rodrigues, E.; Rodrigues, F.; Rodriguez Cobo, C.; Rodriguez Perez, P.; Rogers, G.J.; Romanovsky, V.; Rospabe, G.; Ruf, T.; Ruiz, H.; Sabatino, G.; Saborido Silva, J.J.; Sagidova, N.; Saitta, B.; Salzmann, C.; Sambade Varela, A.; Sannino, M.; Santacesaria, R.; Santinelli, R.; Santovetti, E.; Sapunov, M.; Sarti, A.; Satriano, C.; Satta, A.; Savrie, M.; Savrina, D.; Schaack, P.; Schiller, M.; Schleich, S.; Schmelling, M.; Schmidt, B.; Schneider, O.; Schopper, A.; Schune, M.H.; Schwemmer, R.; Sciubba, A.; Seco, M.; Semennikov, A.; Senderowska, K.; Serra, N.; Serrano, J.; Shao, B.; Shapkin, M.; Shapoval, I.; Shatalov, P.; Shcheglov, Y.; Shears, T.; Shekhtman, L.; Shevchenko, V.; Simioni, E.; Skottowe, H.P.; Skwarnicki, T.; Smith, A.C.; Sobczak, K.; Soler, F.J.P.; Solomin, A.; Somogy, P.; Soomro, F.; De Paula, B.Souza; Spaan, B.; Sparkes, A.; Spiridenkov, E.; Spradlin, P.; Stagni, F.; Steinkamp, O.; Stoica, S.; Stone, S.; Straumann, U.; Styles, N.; Syryczynski, K.; Szczekowski, M.; Szczypka, P.; Szumlak, T.; T'Jampens, S.; Terrier, H.; Teubert, F.; Thomas, C.; Thomas, E.; Tobin, M.; Topp-Joergensen, S.; Tran, M.T.; Traynor, S.; Tsaregorodtsev, A.; Tuning, N.; Ukleja, A.; Ullaland, O.; Uwer, U.; Vagnoni, V.; Valenti, G.; van Beuzekom, M.; van den Brand, J.; van Eijk, D.; van Herwijnen, E.; van Lysebetten, A.; van Tilburg, J.; Vazquez Gomez, R.; Vazquez Regueiro, P.; Vecchi, S.; Velthuis, J.J.; Veltri, M.; Vervink, K.; Viaud, B.; Videau, I.; Vilasis-Cardona, X.; Vollhardt, A.; Vorobyev, A.; Vorobyev, An.; Voss, H.; Wacker, K.; Wandernoth, S.; Wang, J.; Ward, D.R.; Websdale, D.; Whitehead, M.; Wiedner, D.; Wiggers, L.; Wilkinson, G.; Williams, M.; Wilson, F.F.; Witek, M.; Witzeling, W.; Wotton, S.A.; Wyllie, K.; Xie, Y.; Xing, F.; Yang, Z.; Ybeles Smit, G.; Young, R.; Yushchenko, O.; Zhang, L.; Zhang, Y.; Zhelezov, A.; Zwahlen, N.

2010-01-01

Six of the key physics measurements that will be made by the LHCb experiment, concerning CP asymmetries and rare B decays, are discussed in detail. The "road map" towards the precision measurements is presented, including the use of control channels and other techniques to understand the performance of the detector with the first data from the LHC.

Road structural elements temperature trends diagnostics using sensory system of own design

Science.gov (United States)

Dudak, Juraj; Gaspar, Gabriel; Sedivy, Stefan; Pepucha, Lubomir; Florkova, Zuzana

2017-09-01

A considerable funds is spent for the roads maintenance in large areas during the winter. The road maintenance is significantly affected by the temperature change of the road structure. In remote locations may occur a situation, when it is not clear whether the sanding is actually needed because the lack of information on road conditions. In these cases, the actual road conditions are investigated by a personal inspection or by sending out a gritting vehicle. Here, however, is a risk of unnecessary trip the sanding vehicle. This situation is economically and environmentally unfavorable. The proposed system solves the problem of measuring the temperature profile of the road and the utilization of the predictive model to determine the future development trend of temperature. The system was technically designed as a set of sensors to monitor environmental values such as the temperature of the road, ambient temperature, relative air humidity, solar radiation and atmospheric pressure at the measuring point. An important part of the proposal is prediction model which based on the inputs from sensors and historical measurements can, with some probability, predict temperature trends at the measuring point. The proposed system addresses the economic and environmental aspects of winter road maintenance.

A model for investigating the influence of road surface texture and tyre tread pattern on rolling resistance

Science.gov (United States)

Hoever, Carsten; Kropp, Wolfgang

2015-09-01

The reduction of rolling resistance is essential for a more environmentally friendly road transportation sector. Both tyre and road design can be utilised to reduce rolling resistance. In both cases a reliable simulation tool is needed which is able to quantify the influence of design parameters on the rolling resistance of a tyre rolling on a specific road surface. In this work a previously developed tyre/road interaction model is extended to account for different tread patterns and for losses due to small-scale tread deformation. Calculated contact forces and tyre vibrations for tyre/road interaction under steady-state rolling are used to predict rolling losses in the tyre. Rolling resistance is calculated for a series of different tyre/road combinations. Results are compared with rolling resistance measurements. The agreement between simulations and measurements is generally very good. It is found that both the tyre structure and small-scale tread deformations contribute to the rolling losses. The small-scale contribution depends mainly on the road roughness profile. The mean profile depth of the road surface is identified to correlate very well with the rolling resistance. Additional calculations are performed for non-traditional rubberised road surfaces, however, with mixed results. This possibly indicates the existence of additional loss mechanisms for these surfaces.

How Effective Is Road Mitigation at Reducing Road-Kill? A Meta-Analysis.

Science.gov (United States)

Rytwinski, Trina; Soanes, Kylie; Jaeger, Jochen A G; Fahrig, Lenore; Findlay, C Scott; Houlahan, Jeff; van der Ree, Rodney; van der Grift, Edgar A

2016-01-01

Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill). For road planners, deciding on what mitigation method to use has been problematic because there is little good information about the relative effectiveness of these measures in reducing road-kill, and the costs of these measures vary greatly. We conducted a meta-analysis using data from 50 studies that quantified the relationship between road-kill and a mitigation measure designed to reduce road-kill. Overall, mitigation measures reduce road-kill by 40% compared to controls. Fences, with or without crossing structures, reduce road-kill by 54%. We found no detectable effect on road-kill of crossing structures without fencing. We found that comparatively expensive mitigation measures reduce large mammal road-kill much more than inexpensive measures. For example, the combination of fencing and crossing structures led to an 83% reduction in road-kill of large mammals, compared to a 57% reduction for animal detection systems, and only a 1% for wildlife reflectors. We suggest that inexpensive measures such as reflectors should not be used until and unless their effectiveness is tested using a high-quality experimental approach. Our meta-analysis also highlights the fact that there are insufficient data to answer many of the most pressing questions that road planners ask about the effectiveness of road mitigation measures, such as whether other less common mitigation measures (e.g., measures to reduce traffic volume and/or speed) reduce road mortality, or to what extent the attributes of crossing structures and fences influence their effectiveness. To improve evaluations of mitigation effectiveness, studies should incorporate data collection before the mitigation is applied, and we recommend a

How Effective Is Road Mitigation at Reducing Road-Kill? A Meta-Analysis.

Directory of Open Access Journals (Sweden)

Trina Rytwinski

Full Text Available Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill. For road planners, deciding on what mitigation method to use has been problematic because there is little good information about the relative effectiveness of these measures in reducing road-kill, and the costs of these measures vary greatly. We conducted a meta-analysis using data from 50 studies that quantified the relationship between road-kill and a mitigation measure designed to reduce road-kill. Overall, mitigation measures reduce road-kill by 40% compared to controls. Fences, with or without crossing structures, reduce road-kill by 54%. We found no detectable effect on road-kill of crossing structures without fencing. We found that comparatively expensive mitigation measures reduce large mammal road-kill much more than inexpensive measures. For example, the combination of fencing and crossing structures led to an 83% reduction in road-kill of large mammals, compared to a 57% reduction for animal detection systems, and only a 1% for wildlife reflectors. We suggest that inexpensive measures such as reflectors should not be used until and unless their effectiveness is tested using a high-quality experimental approach. Our meta-analysis also highlights the fact that there are insufficient data to answer many of the most pressing questions that road planners ask about the effectiveness of road mitigation measures, such as whether other less common mitigation measures (e.g., measures to reduce traffic volume and/or speed reduce road mortality, or to what extent the attributes of crossing structures and fences influence their effectiveness. To improve evaluations of mitigation effectiveness, studies should incorporate data collection before the mitigation is applied, and we

How Effective Is Road Mitigation at Reducing Road-Kill? A Meta-Analysis

Science.gov (United States)

Rytwinski, Trina; Soanes, Kylie; Jaeger, Jochen A. G.; Fahrig, Lenore; Findlay, C. Scott; Houlahan, Jeff; van der Ree, Rodney; van der Grift, Edgar A

2016-01-01

Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill). For road planners, deciding on what mitigation method to use has been problematic because there is little good information about the relative effectiveness of these measures in reducing road-kill, and the costs of these measures vary greatly. We conducted a meta-analysis using data from 50 studies that quantified the relationship between road-kill and a mitigation measure designed to reduce road-kill. Overall, mitigation measures reduce road-kill by 40% compared to controls. Fences, with or without crossing structures, reduce road-kill by 54%. We found no detectable effect on road-kill of crossing structures without fencing. We found that comparatively expensive mitigation measures reduce large mammal road-kill much more than inexpensive measures. For example, the combination of fencing and crossing structures led to an 83% reduction in road-kill of large mammals, compared to a 57% reduction for animal detection systems, and only a 1% for wildlife reflectors. We suggest that inexpensive measures such as reflectors should not be used until and unless their effectiveness is tested using a high-quality experimental approach. Our meta-analysis also highlights the fact that there are insufficient data to answer many of the most pressing questions that road planners ask about the effectiveness of road mitigation measures, such as whether other less common mitigation measures (e.g., measures to reduce traffic volume and/or speed) reduce road mortality, or to what extent the attributes of crossing structures and fences influence their effectiveness. To improve evaluations of mitigation effectiveness, studies should incorporate data collection before the mitigation is applied, and we recommend a

Comparison of the predictions of two road dust emission models with the measurements of a mobile van

Science.gov (United States)

Kauhaniemi, M.; Stojiljkovic, A.; Pirjola, L.; Karppinen, A.; Härkönen, J.; Kupiainen, K.; Kangas, L.; Aarnio, M. A.; Omstedt, G.; Denby, B. R.; Kukkonen, J.

2014-09-01

The predictions of two road dust suspension emission models were compared with the on-site mobile measurements of suspension emission factors. Such a quantitative comparison has not previously been reported in the reviewed literature. The models used were the Nordic collaboration model NORTRIP (NOn-exhaust Road TRaffic Induced Particle emissions) and the Swedish-Finnish FORE model (Forecasting Of Road dust Emissions). These models describe particulate matter generated by the wear of road surface due to traction control methods and processes that control the suspension of road dust particles into the air. An experimental measurement campaign was conducted using a mobile laboratory called SNIFFER, along two selected road segments in central Helsinki in 2007 and 2008. The suspended PM10 concentration was measured behind the left rear tyre and the street background PM10 concentration in front of the van. Both models reproduced the measured seasonal variation of suspension emission factors fairly well during both years at both measurement sites. However, both models substantially under-predicted the measured emission values. The article illustrates the challenges in conducting road suspension measurements in densely trafficked urban conditions, and the numerous requirements for input data that are needed for accurately applying road suspension emission models.

Automated vehicle location, data recording, friction measurement and applicator control for winter road maintenance.

Science.gov (United States)

2010-02-01

The first part of this project conducted a detailed evaluation of the ability of a new friction measurement system to : provide an accurate measure of road conditions. A system that records friction coefficient as a function of road : location was de...

Towards safer roads : non-technical measures to improve road safety. Paper presented at the seminar `Black spots' in Wisla, Poland, April, 15-20, 1996.

NARCIS (Netherlands)

Goldenbeld, C. & Noordzij, P.C.

1996-01-01

This paper discusses engineering, education and enforcement in relation to hazardous road situations. If a high risk road or road site has been identified, the question is which selection of technical and non-technical measures should be taken to prevent or reduce the danger. The main argument is

Strabo's roads

DEFF Research Database (Denmark)

Bekker-Nielsen, Tønnes

2017-01-01

in the Geography, and the world-view, of Strabo. Strabo did not take much interest in roads as artefacts or monuments, in the technology of road construction, or in the mythological and historical background of individual roads. He is primarily interested in roads from a functional point of view. For the general......To ancient geographers, roads were important not only as arteries of communication, but also as sources of information, since mileages measured along the Roman highways were among the very few precise distances available to the ancient geographer. This chapter explores the place of roads...... or the statesman, roads provide routes of communication; for the systematic geographer, they provide measured distances and directions. Through case studies of Spain, Gaul, Italy, Greece and Anatolia, this chapter attempts to reach a better understanding of the place of roads in Strabo’s universe, especially two...

Knowledge of commercial bus drivers about road safety measures in Lagos, Nigeria.

Science.gov (United States)

Okafor Ifeoma, P; Odeyemi Kofoworola, A; Dolapo Duro, C

2013-01-01

Road traffic injuries have persisted as a serious public health problem and much of the health burden is in developing countries. Over-speeding, poor enforcement of traffic regulations and commuter buses have been highly implicated in road traffic injuries in developing countries. The aim of this study was to determine drivers' knowledge of selected road safety measures, i.e. the pre-requisites for driver's license, road signs and speed limits. This was a cross-sectional study carried out in Lagos, Nigeria. Simple random sampling was used to select the two motor parks used for the study and all the consenting commercial minibus drivers operating within the parks (407) were included in the study. Data was collected with a pre-tested, structured, interviewer-administered questionnaire and analyzed with epi-info statistical software. Two hundred and sixty-one (64.1%) of them knew that Visual Acuity test should be done before obtaining driver's license and 53.8% knew the correct minimum age for obtaining driver's license. Only 1% of the drivers had correct knowledge of the driver's license authorities in Nigeria. The drivers had poor knowledge of road signs (59.0%) and poor knowledge of maximum speed limits (100%). The oldest, least educated and least experienced drivers had the poorest level of knowledge. The drivers demonstrated poor knowledge of road safety measures. There is need for driver education to improve their knowledge.

Polar measurements on profiles

Energy Technology Data Exchange (ETDEWEB)

Althaus, D.

1985-03-01

Wind tunnel models with a profile depth of t=0.5 m were measured in a laminar wind tunnel by the usual measuring processes. The profile resistance was determined by integration along the width of span. The smooth profiles were examined at Re=0.7/1.0 and 1.5 million. At Re=1.0 million, the position of the changeover points were determined with a stethoscope. Also at this Reynolds number measurements were taken with a trip wire of d=2 mm diameter, directly on the profile nose. The tables contain the co-ordinates of the profiles, the contours, the theoretical speed distributions for 4 different angles of attack, the csub(a)-csub(w) polar measurements and changeover points, and the torque coefficients around the t/4 point. (BR).

Measuring Algorithm for the Distance to a Preceding Vehicle on Curve Road Using On-Board Monocular Camera

Science.gov (United States)

Yu, Guizhen; Zhou, Bin; Wang, Yunpeng; Wun, Xinkai; Wang, Pengcheng

2015-12-01

Due to more severe challenges of traffic safety problems, the Advanced Driver Assistance Systems (ADAS) has received widespread attention. Measuring the distance to a preceding vehicle is important for ADAS. However, the existing algorithm focuses more on straight road sections than on curve measurements. In this paper, we present a novel measuring algorithm for the distance to a preceding vehicle on a curve road using on-board monocular camera. Firstly, the characteristics of driving on the curve road is analyzed and the recognition of the preceding vehicle road area is proposed. Then, the vehicle detection and distance measuring algorithms are investigated. We have verified these algorithms on real road driving. The experimental results show that this method proposed in the paper can detect the preceding vehicle on curve roads and accurately calculate the longitudinal distance and horizontal distance to the preceding vehicle.

Sustainability of road roughness measurements in countries with ...

African Journals Online (AJOL)

A research project was carried out to establish a sustainable procedure for road roughness measurement applicable in developing countries. Out of many devices in use today, a vehicle mounted bump integrator (VMBI) was selected for the reasons that: a) the equipment is available in most developing countries and it has ...

Design and testing of an innovative measurement device for tyre-road contact forces

Science.gov (United States)

Cheli, F.; Braghin, F.; Brusarosco, M.; Mancosu, F.; Sabbioni, E.

2011-08-01

The measurement of tyre-road contact forces is the first step towards the development of new control systems for improving vehicle safety and performances. Tyre-road contact forces measurement systems are very expensive and significantly modify the unsprung masses of the vehicle as well as the rotational inertia of the tyres. Thus, vehicle dynamics results are significantly affected. As a consequence, the measured contact forces do not correspond to the contact forces under real working conditions. A new low-cost tyre-road contact forces measurement system is proposed in this paper that can be applied to passenger cars. Its working principle is based on the measurement of three deformations of the wheel rim through strain gauges. The tyre-rim assembly is thus turned into a sensor for tyre-road contact forces. The influence of the strain gauges position onto the measurement results has been assessed through finite element simulations and experimental tests. It has been proven that, for a large variety of rims, the strain gauge position that leads to high signal-to-noise ratios is almost the same. A dynamic calibration procedure has been developed in order to allow the reconstruction of contact force and torque components once per wheel turn. The capability of the developed device to correctly estimate tyre-road contact forces has been assessed, in a first stage, through indoor laboratory experimental test on an MTS Flat-Trac ® testing machine. Results show that the implemented measuring system allows to reconstruct contact forces once per wheel turn with a precision that is comparable to that of existing high-cost measurement systems. Subsequently, outdoor tests with a vehicle having all four wheels equipped with the developed measuring device have also been performed. Reliability of the measurements provided by the developed sensor has been assessed by comparing the global measured longitudinal/lateral forces and the product of the measured longitudinal

Cost/effectiveness aspects of road lighting : contribution to CIE TC 4.6 Symposium on Measures of Road Lighting Effectiveness, Karlsruhe, 5-6 July, 1977. Session II - Road lighting and accidents.

NARCIS (Netherlands)

Flury, F.C.

1977-01-01

The common method to determine the effect of road lighting on traffic safety, is to compare accident numbers during daylight and darkness, before and after the measure is taken. This approach ignores the possibility of increased risk of collisions with road side obstacles due to the erection of

Vehicle-based road dust emission measurement (III):. effect of speed, traffic volume, location, and season on PM 10 road dust emissions in the Treasure Valley, ID

Science.gov (United States)

Etyemezian, V.; Kuhns, H.; Gillies, J.; Chow, J.; Hendrickson, K.; McGown, M.; Pitchford, M.

The testing re-entrained aerosol kinetic emissions from roads (TRAKER) road dust measurement system was used to survey more than 400 km of paved roads in southwestern Idaho during 3-week sampling campaigns in winter and summer, 2001. Each data point, consisting of a 1-s measurement of particle light scattering sampled behind the front tire, was associated with a link (section of road) in the traffic demand model network for the Treasure Valley, ID. Each link was in turn associated with a number of characteristics including posted speed limit, vehicle kilometers traveled (vkt), road class (local/residential, collector, arterial, and interstate), county, and land use (urban vs. rural). Overall, the TRAKER-based emission factors based on location, setting, season, and speed spanned a narrow range from 3.6 to 8.0 g/vkt. Emission factors were higher in winter compared to summer, higher in urban areas compared to rural, and lower for roads with fast travel speeds compared to slower roads. The inherent covariance between traffic volume and traffic speed obscured the assessment of the effect of traffic volume on emission potentials. Distance-based emission factors expressed in grams per kilometer traveled (g/vkt) for roads with low travel speeds (˜11 m/s residential roads) compared to those with high travel speeds (˜25 m/s interstates) were higher (5.2 vs. 3.0 g/vkt in summer and 5.9 vs. 4.9 g/vkt in winter). However, emission potentials which characterize the amount of suspendable material on a road were substantially higher on roads with low travel speeds (0.71 vs. 0.13 g/vkt/(m/s) in summer and 0.78 vs. 0.21 g/vkt/(m/s) in winter). This suggested that while high speed roads are much cleaner (factor of 5.4 in summer), on a vehicle kilometer traveled basis, emissions from high and low speed roads are of the same order. Emission inventories based on the TRAKER method, silt loadings obtained during the field study, and US EPA's AP-42 default values of silt loading were

Investigating the road surface effect to the fatigue life of an automotive coil spring

Science.gov (United States)

Putra, T. E.; Husaini

2018-05-01

This work aims to estimate the life of a coil spring considering road surface profiles. Strain signals were measured by installing a strain gage at the highest stress location of the coil spring and then driving the vehicle on country and village roads. The village road gave high amplitudes containing spikes when the tire touched a curb, bump or pothole. These conditions contributed to a higher loading rate to the car component, contributing to shorter useful fatigue life, which was only 140 reversals of blocks. Driving on the village road resulted in a 6-times decrease in the useful fatigue life of the component in comparison to the country road. In conclusion, the village road caused stronger vibrations to the component because it has a rough surface; meanwhile, the country road provided lower vibrations because the road was smooth.

How Effective Is Road Mitigation at Reducing Road-Kill? A Meta-Analysis

OpenAIRE

Rytwinski, Trina; Soanes, Kylie; Jaeger, Jochen A. G.; Fahrig, Lenore; Findlay, C. Scott; Houlahan, Jeff; van der Ree, Rodney; van der Grift, Edgar A

2016-01-01

Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill). For road planners, deciding on what mitigation method to use has been problematic because there is little good information about the relative effectiveness of these measures in reducing road-kill, and the costs of these...

Beam profile measurements on RHIC

International Nuclear Information System (INIS)

Connolly, R.; Michnoff, R.; Moore, T.; Shea, T.; Tepikian, S.

2000-01-01

The Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Lab was commissioned during the summer of 1999. Transverse beam profiles on RHIC are measured with ionization profile monitors (IPMs). An IPM measures beam profiles by collecting the electrons liberated by residual gas ionization by the beam. The detector is placed in the gap of a dipole magnet to force the electrons to travel in straight lines from the beamline center to the collector. One IPM was tested and it measured the profiles of a single gold bunch containing 10 8 ions on consecutive turns. We show an example of one of these profiles giving transverse emittance. Also several profiles are combined into a mountain-range plot which shows betatron oscillations at injection

Generating strain signals under consideration of road surface profiles

Science.gov (United States)

Putra, T. E.; Abdullah, S.; Schramm, D.; Nuawi, M. Z.; Bruckmann, T.

2015-08-01

The current study aimed to develop the mechanism for generating strain signal utilising computer-based simulation. The strain data, caused by the acceleration, were undertaken from a fatigue data acquisition involving car movements. Using a mathematical model, the measured strain signals yielded to acceleration data used to describe the bumpiness of road surfaces. The acceleration signals were considered as an external disturbance on generating strain signals. Based on this comparison, both the actual and simulated strain data have similar pattern. The results are expected to provide new knowledge to generate a strain signal via a simulation.

A sonification algorithm for developing the off-roads models for driving simulators

Science.gov (United States)

Chiroiu, Veturia; Brişan, Cornel; Dumitriu, Dan; Munteanu, Ligia

2018-01-01

In this paper, a sonification algorithm for developing the off-road models for driving simulators, is proposed. The aim of this algorithm is to overcome difficulties of heuristics identification which are best suited to a particular off-road profile built by measurements. The sonification algorithm is based on the stochastic polynomial chaos analysis suitable in solving equations with random input data. The fluctuations are generated by incomplete measurements leading to inhomogeneities of the cross-sectional curves of off-roads before and after deformation, the unstable contact between the tire and the road and the unreal distribution of contact and friction forces in the unknown contact domains. The approach is exercised on two particular problems and results compare favorably to existing analytical and numerical solutions. The sonification technique represents a useful multiscale analysis able to build a low-cost virtual reality environment with increased degrees of realism for driving simulators and higher user flexibility.

Polybrominated diphenyl ethers in road and farmland soils from an e-waste recycling region in Southern China: Concentrations, source profiles, and potential dispersion and deposition

International Nuclear Information System (INIS)

Luo Yong; Luo Xiaojun; Lin Zhen; Chen Shejun; Liu Juan; Mai Bixian; Yang Zhongyi

2009-01-01

The present study analyzed road soils collected near the dismantling workshops of an e-waste recycling region in South China to determine the PBDE profiles. Farmland soils at a distance of about 2 km from the dismantling workshops were also collected to evaluate the potential dispersion and deposition of PBDEs in the surrounding environment. Total PBDE concentrations ranged from 191 to 9156 ng/g dry weight in road soils and from 2.9 to 207 ng/g dry weight in farmland soils, respectively. Three PBDE source profiles were observed from the road soils by principal component analysis, and were compared with the congener patterns in different technical products. Elevated abundances of octa- and nona-congeners were found in the 'deca-' derived PBDEs as compared with the deca-BDE products. The results in this study suggest that debromination of BDE 209 may have occurred during the use of electric and electronic equipment and/or another technical formulation (Bromkal 79-8DE) was also likely the source of octa- and nona-congeners in e-wastes. Comparison of the PBDE patterns in road and farmland soils implied that the PBDEs in farmland soils have been subject to complex environmental processes

Chemical profiling of PM10 from urban road dust.

Science.gov (United States)

Alves, C A; Evtyugina, M; Vicente, A M P; Vicente, E D; Nunes, T V; Silva, P M A; Duarte, M A C; Pio, C A; Amato, F; Querol, X

2018-09-01

Road dust resuspension is one of the main sources of particulate matter with impacts on air quality, health and climate. With the aim of characterising the thoracic fraction, a portable resuspension chamber was used to collect road dust from five main roads in Oporto and an urban tunnel in Braga, north of Portugal. The PM 10 samples were analysed for: i) carbonates by acidification and quantification of the evolved CO 2 , ii) carbonaceous content (OC and EC) by a thermo-optical technique, iii) elemental composition by ICP-MS and ICP-AES after acid digestion, and iv) organic speciation by GC-MS. Dust loadings of 0.48±0.39mgPM 10 m -2 were obtained for asphalt paved roads. A much higher mean value was achieved in a cobbled pavement (50mgPM 10 m -2 ). In general, carbonates were not detected in PM 10 . OC and EC accounted for PM 10 mass fractions up to 11% and 5%, respectively. Metal oxides accounted for 29±7.5% of the PM 10 mass from the asphalt paved roads and 73% in samples from the cobbled street. Crustal and anthropogenic elements, associated with tyre and brake wear, dominated the inorganic fraction. PM 10 comprised hundreds of organic constituents, including hopanoids, n-alkanes and other aliphatics, polycyclic aromatic hydrocarbons (PAH), alcohols, sterols, various types of acids, glycerol derivatives, lactones, sugars and derivatives, phenolic compounds and plasticizers. In samples from the cobbled street, these organic classes represented only 439μgg -1 PM 10 , while for other pavements mass fractions up to 65mgg -1 PM 10 were obtained. Except for the cobbled street, on average, about 40% of the analysed organic fraction was composed of plasticizers. Although the risk via inhalation of PAH was found to be insignificant, the PM 10 from some roads can contribute to an estimated excess of 332 to 2183 per million new cancer cases in adults exposed via ingestion and dermal contact. Copyright © 2018 Elsevier B.V. All rights reserved.

How effective is road mitigation at reducing road-kill? A meta-analysis

NARCIS (Netherlands)

Rytwinski, Trina; Soanes, Kylie; Jaeger, Jochen A.G.; Fahrig, Lenore; Findlay, C.S.; Houlahan, Jeff; Ree, van der Rodney; Grift, van der Edgar A.

2016-01-01

Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill). For road planners,

International Roughness Index (IRI) measurement using Hilbert-Huang transform

Science.gov (United States)

Zhang, Wenjin; Wang, Ming L.

2018-03-01

International Roughness Index (IRI) is an important metric to measure condition of roadways. This index is usually used to justify the maintenance priority and scheduling for roadways. Various inspection methods and algorithms are used to assess this index through the use of road profiles. This study proposes to calculate IRI values using Hilbert-Huang Transform (HHT) algorithm. In particular, road profile data is provided using surface radar attached to a vehicle driving at highway speed. Hilbert-Huang transform (HHT) is used in this study because of its superior properties for nonstationary and nonlinear data. Empirical mode decomposition (EMD) processes the raw data into a set of intrinsic mode functions (IMFs), representing various dominating frequencies. These various frequencies represent noises from the body of the vehicle, sensor location, and the excitation induced by nature frequency of the vehicle, etc. IRI calculation can be achieved by eliminating noises that are not associated with the road profile including vehicle inertia effect. The resulting IRI values are compared favorably to the field IRI values, where the filtered IMFs captures the most characteristics of road profile while eliminating noises from the vehicle and the vehicle inertia effect. Therefore, HHT is an effect method for road profile analysis and for IRI measurement. Furthermore, the application of HHT method has the potential to eliminate the use of accelerometers attached to the vehicle as part of the displacement measurement used to offset the inertia effect.

Is road safety management linked to road safety performance?

Science.gov (United States)

Papadimitriou, Eleonora; Yannis, George

2013-10-01

This research aims to explore the relationship between road safety management and road safety performance at country level. For that purpose, an appropriate theoretical framework is selected, namely the 'SUNflower' pyramid, which describes road safety management systems in terms of a five-level hierarchy: (i) structure and culture, (ii) programmes and measures, (iii) 'intermediate' outcomes'--safety performance indicators (SPIs), (iv) final outcomes--fatalities and injuries, and (v) social costs. For each layer of the pyramid, a composite indicator is implemented, on the basis of data for 30 European countries. Especially as regards road safety management indicators, these are estimated on the basis of Categorical Principal Component Analysis upon the responses of a dedicated road safety management questionnaire, jointly created and dispatched by the ETSC/PIN group and the 'DaCoTA' research project. Then, quasi-Poisson models and Beta regression models are developed for linking road safety management indicators and other indicators (i.e. background characteristics, SPIs) with road safety performance. In this context, different indicators of road safety performance are explored: mortality and fatality rates, percentage reduction in fatalities over a given period, a composite indicator of road safety final outcomes, and a composite indicator of 'intermediate' outcomes (SPIs). The results of the analyses suggest that road safety management can be described on the basis of three composite indicators: "vision and strategy", "budget, evaluation and reporting", and "measurement of road user attitudes and behaviours". Moreover, no direct statistical relationship could be established between road safety management indicators and final outcomes. However, a statistical relationship was found between road safety management and 'intermediate' outcomes, which were in turn found to affect 'final' outcomes, confirming the SUNflower approach on the consecutive effect of each layer

Road pricing policy implementation

NARCIS (Netherlands)

Vonk Noordegraaf, D.M.

2016-01-01

Urban areas suffer from the negative externalities of road transport like congested road networks, air pollution and road traffic accidents. A measure to reduce these negative externalities is road pricing, meaning policies that impose direct charges on road use (Jones and Hervik, 1992). Since the

Tyre-road friction coefficient estimation based on tyre sensors and lateral tyre deflection: modelling, simulations and experiments

Science.gov (United States)

Hong, Sanghyun; Erdogan, Gurkan; Hedrick, Karl; Borrelli, Francesco

2013-05-01

The estimation of the tyre-road friction coefficient is fundamental for vehicle control systems. Tyre sensors enable the friction coefficient estimation based on signals extracted directly from tyres. This paper presents a tyre-road friction coefficient estimation algorithm based on tyre lateral deflection obtained from lateral acceleration. The lateral acceleration is measured by wireless three-dimensional accelerometers embedded inside the tyres. The proposed algorithm first determines the contact patch using a radial acceleration profile. Then, the portion of the lateral acceleration profile, only inside the tyre-road contact patch, is used to estimate the friction coefficient through a tyre brush model and a simple tyre model. The proposed strategy accounts for orientation-variation of accelerometer body frame during tyre rotation. The effectiveness and performance of the algorithm are demonstrated through finite element model simulations and experimental tests with small tyre slip angles on different road surface conditions.

Measuring water and sediment discharge from a road plot with a settling basin and tipping bucket

Science.gov (United States)

Thomas A. Black; Charles H. Luce

2013-01-01

A simple empirical method quantifies water and sediment production from a forest road surface, and is well suited for calibration and validation of road sediment models. To apply this quantitative method, the hydrologic technician installs bordered plots on existing typical road segments and measures coarse sediment production in a settling tank. When a tipping bucket...

Removing Traffic Emissions from CO2 Time Series Measured at a Tall Tower Using on-Road Measurements and WRF-Stilt Transport Modeling

Science.gov (United States)

Schmidt, A.; Rella, C.; Goeckede, M.; Hanson, C. V.; Yang, Z.; Law, B. E.

2014-12-01

In recent years, measurements of atmospheric carbon dioxide with high precision and accuracy have become increasingly important for climate change research, in particular to inform terrestrial biosphere models. Anthropogenic carbon dioxide emissions from fossil fuel burning have long been recognized to contribute a significant portion of the carbon dioxide in the atmosphere. Here, we present an approach to remove the traffic related carbon dioxide emissions from mole fractions measured at a tall tower by using the corresponding carbon monoxide measurements in combination with footprint analyses and transport modeling. This technique improves the suitability of the CO2 data to be used in inverse modeling approaches of atmosphere-biosphere exchange that do not account for non-biotic portions of CO2. In our study region in Oregon, road traffic emissions are the biggest source of anthropogenic carbon dioxide and carbon monoxide. A three-day mobile campaign covering 1700 km of roads in northwestern Oregon was performed during summer of 2012 using a laser-based Cavity Ring Down Spectrometer. The mobile measurements incorporated different roads including main highways, urban streets, and back-roads, largely within the typical footprint of a tall CO2 observation tower in Oregon's Willamette Valley. For the first time, traffic related CO:CO2 emission ratios were measured directly at the sources during an on-road campaign under a variety of different driving conditions. An average emission ratio of 7.43 (±1.80) ppb CO per ppm CO2 was obtained for the study region and applied to separate the traffic related portion of CO2 from the mole fraction time series. The road traffic related portion of the CO2 mole fractions measured at the tower site reached maximum values from 9.8 to 12 ppm, depending on the height above the surface, during summer 2012.

Motorcycle On-Road Driving Parameters Influencing Fuel Consumption and Emissions on Congested Signalized Urban Corridor

Directory of Open Access Journals (Sweden)

Atthapol Seedam

2017-01-01

Full Text Available This study aims to find the on-road driving parameters influencing fuel consumption and emissions of motorcycle driving on a congested signalized urban corridor. A motorcycle onboard measurement system was developed to measure instantaneously and continuously record on-road driving data, including speed-time profile, emissions, and fuel consumption, by the second. The test motorcycles were driven by 30 sample motorcyclists on a signalized urban corridor in Khon Kaen City, Thailand, to collect their on-road driving behavior during the morning peak period. Cluster analysis was applied to analyze collected driving data and to categorize the drivers by level of fuel consumption and on-road driver behavior. The on-road driving parameter influencing fuel consumption and emissions was then determined. Results revealed that proportion of idle time significantly influenced fuel consumption and emissions of motorcycle driving on a congested signalized urban corridor, though aggressive driving behavior, hard acceleration and deceleration, did not have the same kind of influence.

Safer Roads: Comparisons Between Road Assessment Program and Composite Road Safety Index Method

Directory of Open Access Journals (Sweden)

Mohd Razelan Intan Suhana

2017-01-01

Full Text Available In most countries, crash statistics have becoming very crucial in evaluating road’s safety level. In Malaysia, these data are very important in deciding crash-prone areas known as black spot where specific road improvements plan will be proposed. However due to the unavailability of reliable crash data in many developing countries, appropriate road maintenance measures are facing great troubles. In light of that, several proactive methods in defining road’s safety level such as Road Assessment Program (RAP have emerged. This research aim to compare two proactive methods that have been tested in Malaysian roads ; road assessment program and road environment risk index which was developed based on composite index theory in defining road’s safety level. Composite road environment risk index was combining several crucial environment indicators, assigning weight and aggregating the individual index together to form a single value representing the road’s safety level. Based on the results, it can be concluded that both road assessment program and composite road environment risk index are contradicted in six different ways such as type of speed used, type of analysis used and their final outcomes. However, with an aim to promote safer roads, these two methods can be used concurrently as the outcomes in both methods seems to fulfil each other’s gap very well.

The implementation of nuclear methods for density measurements on Romanian roads

International Nuclear Information System (INIS)

Tripadus, V.; Craciun, L.; Peticila, M.; Florea, N.

2000-01-01

The implementation of nuclear methods in field measurements presumes steps concerning the fulfillment of the many requirements to be undertaken. First of all the owner of the nuclear equipment must obtain all the documents imposed by the Romanian laws. The second step is connected with the recalibration of the equipment in order to obtain an improved precision of the measurements. In the last few years National Administration of Roads, Research Institute of Roads together with National Institute of Physics and Nuclear Engineering, made many efforts in order to implement nuclear methods destined to determine both the density and the moisture content either on asphalt or on compact soils. The American companies CPN and Troxler produced the equipment. On the basis of the comparison between nuclear and core density measurements the correction factor of the equipment was established. A special attention was paid to the definitions of different physical quantities occurring in Romanian Standards in order to connect them properly with the American ones. (authors)

A review of international sources for road safety measures assessment.

NARCIS (Netherlands)

Yannis, G. Weijermars, W. & Kauppila, J.

2012-01-01

The efficiency assessment of road safety measures is considered to be an extremely useful tool in decision making; in particular, cost-benefit and cost-effectiveness analyses are carried out in several countries, in a more or less systematic way. The objective of this paper is to present findings

Modelling road dust emission abatement measures using the NORTRIP model: Vehicle speed and studded tyre reduction

Science.gov (United States)

Norman, M.; Sundvor, I.; Denby, B. R.; Johansson, C.; Gustafsson, M.; Blomqvist, G.; Janhäll, S.

2016-06-01

Road dust emissions in Nordic countries still remain a significant contributor to PM10 concentrations mainly due to the use of studded tyres. A number of measures have been introduced in these countries in order to reduce road dust emissions. These include speed reductions, reductions in studded tyre use, dust binding and road cleaning. Implementation of such measures can be costly and some confidence in the impact of the measures is required to weigh the costs against the benefits. Modelling tools are thus required that can predict the impact of these measures. In this paper the NORTRIP road dust emission model is used to simulate real world abatement measures that have been carried out in Oslo and Stockholm. In Oslo both vehicle speed and studded tyre share reductions occurred over a period from 2004 to 2006 on a major arterial road, RV4. In Stockholm a studded tyre ban on Hornsgatan in 2010 saw a significant reduction in studded tyre share together with a reduction in traffic volume. The model is found to correctly simulate the impact of these measures on the PM10 concentrations when compared to available kerbside measurement data. Importantly meteorology can have a significant impact on the concentrations through both surface and dispersion conditions. The first year after the implementation of the speed reduction on RV4 was much drier than the previous year, resulting in higher mean concentrations than expected. The following year was much wetter with significant rain and snow fall leading to wet or frozen road surfaces for 83% of the four month study period. This significantly reduced the net PM10 concentrations, by 58%, compared to the expected values if meteorological conditions had been similar to the previous years. In the years following the studded tyre ban on Hornsgatan road wear production through studded tyres decreased by 72%, due to a combination of reduced traffic volume and reduced studded tyre share. However, after accounting for exhaust

Performance standards of road safety management

Directory of Open Access Journals (Sweden)

Čabarkapa Milenko R.

2016-01-01

Full Text Available Road safety management controlling means the process of finding out the information whether the road safety is improving in a measure to achieve the objectives. The process of control consists of three basic elements: definition of performances and standards, measurement of current performances and comparison with the set standards, and improvement of current performances, if they deviate from the set standards. The performance standards of road safety management system are focused on a performances measurement, in terms of their design and characteristics, in order to support the performances improvement of road safety system and thus, ultimately, improve the road safety. Defining the performance standards of road safety management system, except that determines the design of the system for performances measurement, directly sets requirements whose fulfillment will produce a road safety improvement. The road safety management system, based on the performance standards of road safety, with a focus on results, will produce the continuous improvement of road safety, achieving the long-term 'vision zero', the philosophy of road safety, that human life and health take priority over mobility and other traffic objectives of the road traffic.

CLEAN-ROADS project: air quality considerations after the application of a novel MDSS on winter road maintenance activities

Science.gov (United States)

Pretto, Ilaria; Malloci, Elisa; Tonidandel, Gabriele; Benedetti, Guido; Di Napoli, Claudia; Piazza, Andrea; Apolloni, Roberto; Cavaliere, Roberto

2016-04-01

on sodium chloride, which releases Na+ and Cl-, the estimation of the contribution of road salting to PM10 concentration can be carried out considering only measured concentrations of Na+ and Cl-. However, the presence of these elements might not be due exclusively to salting activities. For this reason data collected during first winter campaign were analysed using the Positive Matrix Factorization (PMF) Model developed by United States Environmental Protection Agency (EPA) to identify the presence of Na+ and Cl- in emission profiles of other PM10 sources (e.g., biomass burning, traffic) [3]. Through this study new guidelines have been defined for the optimization of current road management operations, and their applicability to other area in the Province of Trento has been assessed for future purposes. [1] Pretto I. et al., SIRWEC 2014 conference proceedings, ID:0019 (2014) [2] Ambient Air Quality and Cleaner Air for Europe (CAFE) Directive (2008/50/EC) [3] http://www.epa.gov/air-research/positive-matrix-factorization-model-environmental-data-analyses

Vision Hampton Roads : economic performance measures, 2010 DASHBOARD.

Science.gov (United States)

2010-01-01

Mission: Provide leadership to focus on the strategic issues that will improve Hampton Roads' competitive position in the global economy. : Goal: With proper foresight, continuous planning and dynamic economic development, Hampton Roads will be recog...

Road grip test in Arjeplog

OpenAIRE

Engström, Niclas; Andrén, Henrik; Nybacka, Mikael; Fransson, Lennart; Larsson, Roland

2008-01-01

The Swedish road administration sees a need to improve the road grip estimation capacity for the Swedish road system. The challenge is to find methods to measure road grip fast and reliable. There where six different system types at the tests in Arjeplog, three continuous, two system measuring road grip through deceleration and one system based on GPS and accelerometers. Two system types used air craft runway tires. The other systems used either studded winter tires or friction winter tires. ...

Access road reclamation

International Nuclear Information System (INIS)

Manson, T.; Blok, M.

1997-01-01

A general review of the measures involved in restoring abandoned access road sites in British Columbia was presented. Permits and licences are needed for the use of crown land for roads used by the petroleum and natural gas industry for exploration activities. However, the regulatory framework for road site reclamation is not well developed. The nature of access road reclamation is very site-specific. Some of the issues that are considered for all reclamation projects include slope stability, water control, revegetation, soil rehabilitation, access management and monitoring. The primary objective of reclaiming access road sites is to return the site to conditions that are equal or better than pre-disturbance conditions. Restoration measures must be approved by BC Environment and by the Department of Fisheries and Oceans where federal fisheries responsibilities are involved. 54 refs., 5 tabs., 3 figs

Investigation of the impact of low cost traffic engineering measures on road safety in urban areas.

Science.gov (United States)

Yannis, George; Kondyli, Alexandra; Georgopoulou, Xenia

2014-01-01

This paper investigates the impact of low cost traffic engineering measures (LCTEMs) on the improvement of road safety in urban areas. A number of such measures were considered, such as speed humps, woonerfs, raised intersections and other traffic calming measures, which have been implemented on one-way, one-lane roads in the Municipality of Neo Psychiko in the Greater Athens Area. Data were analysed using the before-and-after safety analysis methodology with large control group. The selected control group comprised of two Municipalities in the Athens Greater Area, which present similar road network and land use characteristics with the area considered. The application of the methodology showed that the total number of crashes presented a statistically significant reduction, which can be possibly attributed to the introduction of LCTEMs. This reduction concerns passenger cars and single-vehicle crashes and is possibly due to the behavioural improvement of drivers of 25 years old or more. The results of this research are very useful for the identification of the appropriate low cost traffic engineering countermeasures for road safety problems in urban areas.

Effects of winter road grooming on bison in YNP

Science.gov (United States)

Bjornlie, Daniel D.; Garrott, R.A.

2001-01-01

The effects of winter recreation—specifically snowmobiling—on wildlife in Yellowstone National Park (YNP) have become high-profile management issues. The road grooming needed to support oversnow travel in YNP is also being examined for its effects on bison (Bison bison) ecology. Data were collected from November 1997 through May 1998 and from December 1998 through May 1999 on the effects of road grooming on bison in Madison–Gibbon–Firehole (MGF) area of YNP Peak bison numbers occurred during late March—early April and were strongly correlated with the snow water equivalent measurements in the Hayden Valley area (1997–1998: r* = 0.62, p:0.001: 1998–1999: r2 = 0.64, P-0.001). Data from an infrared trail monitor on the Mary Mountain trail between the Hayden and Firehole valleys suggest that this trail is the sole corridor for major bison distributional shifts between these locations. Of the 28,293 observations of individual bison made during the study, 8% were traveling and 69% were foraging. These percentages were nearly identical during the period of winter road grooming (7% and 68%, respectively). During this period, 77% of bison foraging activity and 12% of bison traveling activity involved displacing snow. Most travel took place off roads (Pgrooming, with peak use in April and lowest use during the road-grooming period. Bison in the MGF area of YNF neither seek out nor avoid groomed roads. The minimal use of roads compared to off-road areas, the short distances traveled on the roads, the decreased use of roads during the over snow vehicle (OSV) season, and the increased costs of negative interactions with OSVs suggest that grooming roads during winter does not have a major influence on bison ecology.

Summary report (CORDIS) [of the European research project] PROMISING (Promotion of Measures for Vulnerable Road Users).

NARCIS (Netherlands)

2013-01-01

The objective of the PROMISING-project was to capitalise on non-restrictive measures and technical developments in a number of areas to minimise the problems of vulnerable and young road users. The potential for problem reduction was specified for four target groups of vulnerable road users:

Comparison of the physical and chemical characteristics of fine road dust at different urban sites.

Science.gov (United States)

Lee, Kwang Yul; Batmunkh, Tsatsral; Joo, Hung Soo; Park, Kihong

2018-04-18

The size distribution and chemical components of a fine fraction (road dust collected at urban sites in Korea (Gwangju) and Mongolia (Ulaanbaatar) where distinct urban characteristics exist were measured. A clear bimodal size distribution was observed for the resuspended fine road dust at the urban sites in Korea. The first mode peaked at 100-110 nm, and the second peak was observed at 435-570 nm. Ultrafine mode (~30 nm) was found for the fine road dust at the Mongolia site, which was significantly affected by residential coal/biomass burning. The contribution of the water-soluble ions to the fine road dust was higher at the sites in Mongolia (15.8-16.8%) than at those in Korea (1.2-4.8%). Sulfate and chloride were the most dominant ionic species for the fine road dust in Mongolia. As (arsenic) was also much higher for the Mongolian road dust than the others. The sulfate, chloride, and As mainly come from coal burning activity, suggesting that coal and biomass combustion in Mongolia during the heating season should affect the size and chemical components of the fine road dust. Cu (copper) and Zn (zinc), carbonaceous particles (organic carbon [OC] and elemental carbon [EC]) increased at sites in Korea, suggesting that the fine road dust at these sites was significantly affected by the high volume of traffic (engine emission and brake/tire wear). Our results suggest that chemical profiles for road dust specific to certain sites should be applied to more accurately apportion road dust source contributing to the ambient particulate matter. Size and chemical characteristics of fine road dust at sites having distinct urban characteristics were examined. Residential coal and biomass burning and traffic affected physiochemical properties of the fine road dust. Different road dust profiles at different sites should be needed to determine the ambient PM2.5 sources more accurately.

Road user behaviour changes following a self-explaining roads intervention.

Science.gov (United States)

Mackie, Hamish W; Charlton, Samuel G; Baas, Peter H; Villasenor, Pablo C

2013-01-01

The self-explaining roads (SER) approach uses road designs that evoke correct expectations and driving behaviours from road users to create a safe and user-friendly road network. Following the implementation of an SER process and retrofitting of local and collector roads in a suburb within Auckland City, lower speeds on local roads and less variation in speed on both local and collector roads were achieved, along with a closer match between actual and perceived safe speeds. Preliminary analyses of crash data shows that the project has resulted in a 30% reduction crash numbers and an 86% reduction in crash costs per annum, since the road changes were completed. In order to further understand the outcomes from this project, a study was carried out to measure the effects of the SER intervention on the activity and behaviour of all road users. Video was collected over nine separate days, at nine different locations, both before and after SER construction. Road user behaviour categories were developed for all potential road users at different location types and then used to code the video data. Following SER construction, on local roads there was a relatively higher proportion of pedestrians, less uniformity in vehicle lane keeping and less indicating by motorists along with less through traffic, reflecting a more informal/low speed local road environment. Pedestrians were less constrained on local roads following SER construction, possibly reflecting a perceptually safer and more user-friendly environment. These behaviours were not generally evident on collector roads, a trend also shown by the previous study of speed changes. Given that one of the objectives of SER is to match road user behaviour with functionally different road categories, the road user behaviour differences demonstrated on different road types within the SER trial area provides further reinforcement of a successful SER trial. Copyright © 2012 Elsevier Ltd. All rights reserved.

Cost/effectiveness aspects of road lighting : revised version of Contribution to CIE TC-4.6 Symposium on Measures of Road Lighting Effectiveness, Session II - Road lighting and accidents, Karlsruhe, 5-6 July 1977, SWOV R-77-46.

NARCIS (Netherlands)

Flury, F.C.

1981-01-01

The common method to determine the effect of road lighting on traffic safety, is to compare accident numbers during daylight and darkness, before and after the measure is taken. This approach ignores the possibility of increased risk of collisions with road side obstacles due to the erection of

Family climate for road safety: a new concept and measure.

Science.gov (United States)

Taubman-Ben-Ari, Orit; Katz-Ben-Ami, Liat

2013-05-01

This research adapted the workplace concept of safety climate to the domain of safe driving, defining a new construct of "family climate for road safety". Four studies were conducted in Israel with the aim of developing and validating a multidimensional instrument to assess this construct among young drivers. Study 1 (n=632) focused on developing the Family Climate for Road Safety Scale (FCRSS), a self-report scale assessing the family climate by means of seven aspects of the parent-child relationship: Modeling, Feedback, Communication, Monitoring, Noncommitment, Messages, and Limits. Significant differences were found between young men and women on all factors. In addition, significant associations were found between the FCRSS factors on the one hand, and the reported frequency of risky driving and personal commitment to safety on the other. Studies 2-4 confirmed the factorial structure of the FCRSS and the reliability of its factors, adding to its criterion and convergent validity. Study 2 (n=178) yielded significant associations between the scale and young drivers' perception of their parents as involved, encouraging autonomy, and providing warmth; Study 3 (n=117) revealed significant associations between the scale and youngsters' reported proneness to take risks while driving, as well as significant associations between the factors and various dimensions of family functioning; and Study 4 (n=156) found associations between the FCRSS factors and both driving styles (risky, angry, anxious, careful) and family cohesion and adaptability. The discussion deals with the validity and utility of the concept of family climate for road safety and its measurement, addressing the practical implications for road safety. Copyright © 2013 Elsevier Ltd. All rights reserved.

Automatic Extraction of Road Markings from Mobile Laser Scanning Data

Science.gov (United States)

Ma, H.; Pei, Z.; Wei, Z.; Zhong, R.

2017-09-01

Road markings as critical feature in high-defination maps, which are Advanced Driver Assistance System (ADAS) and self-driving technology required, have important functions in providing guidance and information to moving cars. Mobile laser scanning (MLS) system is an effective way to obtain the 3D information of the road surface, including road markings, at highway speeds and at less than traditional survey costs. This paper presents a novel method to automatically extract road markings from MLS point clouds. Ground points are first filtered from raw input point clouds using neighborhood elevation consistency method. The basic assumption of the method is that the road surface is smooth. Points with small elevation-difference between neighborhood are considered to be ground points. Then ground points are partitioned into a set of profiles according to trajectory data. The intensity histogram of points in each profile is generated to find intensity jumps in certain threshold which inversely to laser distance. The separated points are used as seed points to region grow based on intensity so as to obtain road mark of integrity. We use the point cloud template-matching method to refine the road marking candidates via removing the noise clusters with low correlation coefficient. During experiment with a MLS point set of about 2 kilometres in a city center, our method provides a promising solution to the road markings extraction from MLS data.

Road Surfaces And Earthquake Engineering: A Theoretical And Experimental Study

International Nuclear Information System (INIS)

Pratico, Filippo Giammaria

2008-01-01

As is well known, road surfaces greatly affect vehicle-road interaction. As a consequence, road surfaces have a paramount influence on road safety and pavement management systems. On the other hand, earthquakes produce deformations able to modify road surface structure, properties and performance. In the light of these facts, the main goal of this paper has been confined into the modelling of road surface before, during and after the seismic event. The fundamentals of road surface texture theory have been stated in a general formulation. Models in the field of road profile generation and theoretical properties, before, during and after the earthquake, have been formulated and discussed. Practical applications can be hypothesised in the field of vehicle-road interaction as a result of road surface texture derived from deformations and accelerations caused by seismic or similar events

The measurement of dry deposition and surface runoff to quantify urban road pollution in Taipei, Taiwan.

Science.gov (United States)

Wang, Yunn-Jinn; Chen, Chi-Feng; Lin, Jen-Yang

2013-10-16

Pollutants deposited on road surfaces and distributed in the environment are a source of nonpoint pollution. Field data are traditionally hard to collect from roads because of constant traffic. In this study, in cooperation with the traffic administration, the dry deposition on and road runoff from urban roads was measured in Taipei City and New Taipei City, Taiwan. The results showed that the dry deposition is 2.01-5.14 g/m(2) · day and 78-87% of these solids are in the 75-300 µm size range. The heavy metals in the dry deposited particles are mainly Fe, Zn, and Na, with average concentrations of 34,978, 1,519 and 1,502 ppm, respectively. Elevated express roads show the highest heavy metal concentrations. Not only the number of vehicles, but also the speed of the traffic should be considered as factors that influence road pollution, as high speeds may accelerate vehicle wear and deposit more heavy metals on road surfaces. In addition to dry deposition, the runoff and water quality was analyzed every five minutes during the first two hours of storm events to capture the properties of the first flush road runoff. The sample mean concentration (SMC) from three roads demonstrated that the first flush runoff had a high pollution content, notably for suspended solid (SS), chemical oxygen demand (COD), oil and grease, Pb, and Zn. Regular sweeping and onsite water treatment facilities are suggested to minimize the pollution from urban roads.

Investigating the Impact of Road Condition Complexity on Driving Workload Based on Subjective Measurement using NASA TLX

Directory of Open Access Journals (Sweden)

Sugiono Sugiono

2017-01-01

Full Text Available Prior researchers indicate that mental load is one of the most important contributors to a traffic accident. The aim of the paper is to investigate the impact and the correlation of road condition and driving experience on driver’s mental workload. The driving test consists of 3 road complicity situation (urban road, highway, rural road with 26 drivers with average 21 years old in different experience level (average 4.08 years’ experience. NASA TLX questioner is used as subjective driver’s mental load measurement with three dimensions relate to the demands imposed on the subject (Mental, Physical and Temporal Demands and three to the interaction of a subject with the task (Effort, Frustration, and Performance. There are 3 cameras placed on the left side, right side and front car to identify the road condition. According to experiment, it was found that drivers felt that frustration level, business, and mental-demand factors dominate the impact on high-level workload (96.15%. Highway road conditions provide an average overall workload score of 62 (OWS which was better compared to city road (OWS = 69 and rural road (OWS = 66. Based on street complexity, it is necessary to improve road conditions that resemble highway road by reducing potential hazard.

Automated pavement horizontal curve measurement methods based on inertial measurement unit and 3D profiling data

Directory of Open Access Journals (Sweden)

Wenting Luo

2016-04-01

Full Text Available Pavement horizontal curve is designed to serve as a transition between straight segments, and its presence may cause a series of driving-related safety issues to motorists and drivers. As is recognized that traditional methods for curve geometry investigation are time consuming, labor intensive, and inaccurate, this study attempts to develop a method that can automatically conduct horizontal curve identification and measurement at network level. The digital highway data vehicle (DHDV was utilized for data collection, in which three Euler angles, driving speed, and acceleration of survey vehicle were measured with an inertial measurement unit (IMU. The 3D profiling data used for cross slope calibration was obtained with PaveVision3D Ultra technology at 1 mm resolution. In this study, the curve identification was based on the variation of heading angle, and the curve radius was calculated with kinematic method, geometry method, and lateral acceleration method. In order to verify the accuracy of the three methods, the analysis of variance (ANOVA test was applied by using the control variable of curve radius measured by field test. Based on the measured curve radius, a curve safety analysis model was used to predict the crash rates and safe driving speeds at horizontal curves. Finally, a case study on 4.35 km road segment demonstrated that the proposed method could efficiently conduct network level analysis.

Awareness and practice of road safety measures among undergraduate medical students in a South Indian state.

Science.gov (United States)

Kulkarni, Vaman; Kanchan, Tanuj; Palanivel, C; Papanna, M K; Kumar, Nithin; Unnikrishnan, B

2013-05-01

The UN general assembly has declared 2011-2020 as the "Decade of Action for Road Safety". The declaration holds significance because road traffic accidents (RTAs) have become a major cause of morbidity and mortality, especially among the adults and middle aged individuals who constitute economically most productive age groups of society. The importance of knowledge and practice of road safety measures needs to be emphasized in the prevention of RTAs. The present study is aimed to assess the knowledge and practice of road safety measures among the students of a medical college in coastal, South India. A total of 260 medical students were included in this cross-sectional study. A semi-structured questionnaire was used to collect the relevant information from the participants. The data collected was analyzed using SPSS version 11.5. Out of the 260 participants, 149 (57.3%) were females and 111 (42.7%) were males. The overall awareness on road safety measures was slightly higher among females (20.6%) than males (19.9%). The participants had significantly low awareness with regard to alcohol and driving (4.2%), use of seat belts (20%) and use of mobile phones without hands free device (6.1%). The participants had a better knowledge about traffic signs and more than half of them identified all the signs correctly. With regard to the road safety practices, 25% were involved in drunken driving in the past one year. The practice of using mobile phones with hands free devices while driving was admitted by 20% of them. Nearly two-third participants (68%) admitted to have crossed speed limits on multiple occasions. Observations of the study emphasize on the need to generate awareness among medical students through training and IEC activities to curb the epidemic of RTAs. Copyright © 2012 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

Electron shower transverse profile measurement

International Nuclear Information System (INIS)

Lednev, A.A.

1993-01-01

A method to measure the shower transverse profile is described. Calibration data of the lead-glass spectrometer GAMS collected in a wide electron beam without any additional coordinate detector are used. The method may be used for the measurements in both cellular- and projective-type spectrometers. The results of measuring the 10 GeV electron shower profile in the GAMS spectrometer, without optical grease between the lead-glass radiators and photomultipliers, are approximated with an analytical function. The estimate of the coordinate accuracy is obtained. 5 refs., 8 figs

The Measurement of Dry Deposition and Surface Runoff to Quantify Urban Road Pollution in Taipei, Taiwan

Science.gov (United States)

Wang, Yunn-Jinn; Chen, Chi-Feng; Lin, Jen-Yang

2013-01-01

Pollutants deposited on road surfaces and distributed in the environment are a source of nonpoint pollution. Field data are traditionally hard to collect from roads because of constant traffic. In this study, in cooperation with the traffic administration, the dry deposition on and road runoff from urban roads was measured in Taipei City and New Taipei City, Taiwan. The results showed that the dry deposition is 2.01–5.14 g/m2·day and 78–87% of these solids are in the 75–300 µm size range. The heavy metals in the dry deposited particles are mainly Fe, Zn, and Na, with average concentrations of 34,978, 1,519 and 1,502 ppm, respectively. Elevated express roads show the highest heavy metal concentrations. Not only the number of vehicles, but also the speed of the traffic should be considered as factors that influence road pollution, as high speeds may accelerate vehicle wear and deposit more heavy metals on road surfaces. In addition to dry deposition, the runoff and water quality was analyzed every five minutes during the first two hours of storm events to capture the properties of the first flush road runoff. The sample mean concentration (SMC) from three roads demonstrated that the first flush runoff had a high pollution content, notably for suspended solid (SS), chemical oxygen demand (COD), oil and grease, Pb, and Zn. Regular sweeping and onsite water treatment facilities are suggested to minimize the pollution from urban roads. PMID:24135820

PHOTOGRAMMETRIC TECHNIQUES FOR ROAD SURFACE ANALYSIS

Directory of Open Access Journals (Sweden)

V. A. Knyaz

2016-06-01

Full Text Available The quality and condition of a road surface is of great importance for convenience and safety of driving. So the investigations of the behaviour of road materials in laboratory conditions and monitoring of existing roads are widely fulfilled for controlling a geometric parameters and detecting defects in the road surface. Photogrammetry as accurate non-contact measuring method provides powerful means for solving different tasks in road surface reconstruction and analysis. The range of dimensions concerned in road surface analysis can have great variation from tenths of millimetre to hundreds meters and more. So a set of techniques is needed to meet all requirements of road parameters estimation. Two photogrammetric techniques for road surface analysis are presented: for accurate measuring of road pavement and for road surface reconstruction based on imagery obtained from unmanned aerial vehicle. The first technique uses photogrammetric system based on structured light for fast and accurate surface 3D reconstruction and it allows analysing the characteristics of road texture and monitoring the pavement behaviour. The second technique provides dense 3D model road suitable for road macro parameters estimation.

Measurement of whole tire profile

Science.gov (United States)

Yang, Yongyue; Jiao, Wenguang

2010-08-01

In this paper, a precision measuring device is developed for obtaining characteristic curve of tire profile and its geometric parameters. It consists of a laser displacement measurement unit, a closed-loop precision two-dimensional coordinate table, a step motor control system and a fast data acquisition and analysis system. Based on the laser trigonometry, a data map of tire profile and coordinate values of all points can be obtained through corresponding data transformation. This device has a compact structure, a convenient control, a simple hardware circuit design and a high measurement precision. Experimental results indicate that measurement precision can meet the customer accuracy requirement of +/-0.02 mm.

Fitting the IRI F2-profile function to measured profiles

International Nuclear Information System (INIS)

Reinisch, B.W.; Huang Xueqin

1997-01-01

Comparison with profile data from ionosondes shows that the IRI bottomside F2-profiles can be improved by using better B0 and B1 parameters. The best parameters (in a least-squares sense) can be easily calculated in a numerical procedure from measured profiles presented as a sum of Chebyshev polynomials. 7 refs, 5 figs, 1 tab

AUTOMATIC EXTRACTION OF ROAD MARKINGS FROM MOBILE LASER SCANNING DATA

Directory of Open Access Journals (Sweden)

H. Ma

2017-09-01

Full Text Available Road markings as critical feature in high-defination maps, which are Advanced Driver Assistance System (ADAS and self-driving technology required, have important functions in providing guidance and information to moving cars. Mobile laser scanning (MLS system is an effective way to obtain the 3D information of the road surface, including road markings, at highway speeds and at less than traditional survey costs. This paper presents a novel method to automatically extract road markings from MLS point clouds. Ground points are first filtered from raw input point clouds using neighborhood elevation consistency method. The basic assumption of the method is that the road surface is smooth. Points with small elevation-difference between neighborhood are considered to be ground points. Then ground points are partitioned into a set of profiles according to trajectory data. The intensity histogram of points in each profile is generated to find intensity jumps in certain threshold which inversely to laser distance. The separated points are used as seed points to region grow based on intensity so as to obtain road mark of integrity. We use the point cloud template-matching method to refine the road marking candidates via removing the noise clusters with low correlation coefficient. During experiment with a MLS point set of about 2 kilometres in a city center, our method provides a promising solution to the road markings extraction from MLS data.

Effect of the Road Environment on Road Safety in Poland

Science.gov (United States)

Budzynski, Marcin; Jamroz, Kazimierz; Antoniuk, Marcin

2017-10-01

Run-off-road accidents tend to be very severe because when a vehicle leaves the road, it will often crash into a solid obstacle (tree, pole, supports, front wall of a culvert, barrier). A statistical analysis of the data shows that Poland’s main roadside hazard is trees and the severity of vehicles striking a tree in a run-off-road crash. The risks are particularly high in north-west Poland with many of the roads lined up with trees. Because of the existing rural road cross-sections, i.e. having trees directly on road edge followed immediately by drainage ditches, vulnerable road users are prevented from using shoulders and made to use the roadway. With no legal definition of the road safety zone in Polish regulations, attempts to remove roadside trees lead to major conflicts with environmental stakeholders. This is why a compromise should be sought between the safety of road users and protection of the natural environment and the aesthetics of the road experience. Rather than just cut the trees, other road safety measures should be used where possible to treat the hazardous spots by securing trees and obstacles and through speed management. Accidents that are directly related to the road environment fall into the following categories: hitting a tree, hitting a barrier, hitting a utility pole or sign, vehicle rollover on the shoulder, vehicle rollover on slopes or in ditch. The main consequence of a roadside hazard is not the likelihood of an accident itself but of its severity. Poland’s roadside accident severity is primarily the result of poor design or operation of road infrastructure. This comes as a consequence of a lack of regulations or poorly defined regulations and failure to comply with road safety standards. The new analytical model was designed as a combination of the different factors and one that will serve as a comprehensive model. It was assumed that it will describe the effect of the roadside on the number of accidents and their consequences

Review on the Pavement-repairing Measures as a Condition for the Choice of Road-Maintenance Strategy

Directory of Open Access Journals (Sweden)

Nedevska Ivana

2017-01-01

Full Text Available The road-maintenance strategies vary from one country to another, and even between the road management authorities within a one single country. It is not surprising, as there is not best maintenance method, nor a universal set of strategies that can be applied equally everywhere. Generally, there are strategies acceptable in certain conditions, but the factors influencing the selection process are diverse and very complex. This paper will present a review of the various measures that can be applied on the roads, which is certainly the basic condition of selection of an appropriate maintenance strategy.

On-road particulate emission measurement

Science.gov (United States)

Mazzoleni, Claudio

Particulate matter (PM) suspended in the atmosphere has harmful health effects, contributes to visibility impairment, and affects atmospheric radiative transfer, thereby contributing to global change. Vehicles contribute substantially to the ambient PM concentration in urban areas, yet the fraction of ambient PM originating from vehicle emissions is poorly characterized because suitable measurement methods have not been available. This dissertation describes the development and the use of a new vehicle emission remote sensing system (VERSS) for the on-road measurement of PM emission factors for vehicles. The PM VERSS measures PM by ultraviolet backscattering and transmission. PM backscattering and transmission mass efficiencies have been calculated from Mie theory based on an homogeneous spherical model for gasoline particles and on a two-layers, spherical model for diesel particles. The VERSS was used in a large-scale study in Las Vegas, NV. A commercial gaseous VERSS was used for the measurement of gaseous emission factors (i.e., carbon monoxide, hydrocarbons, and nitrogen oxide). Speed and acceleration were also measured for each vehicle. A video image of each vehicle's rear license plate was acquired and license plate numbers were matched with the Clark County department of motor vehicle database to retrieve vehicle information such as model year, vehicle weight category and engine ignition type. PM VERSS has precisely estimated PM fleet average emission factors and clearly shown the dependence of PM emission factors on vehicle model year. Under mostly hot-stabilized operation, diesel vehicle PM emission factors are about 25 times higher than those of gasoline vehicles. Furthermore, the fleet frequency distributions of PM emission factors are highly skewed, meaning that most of the fleet emission factor is accounted for by a small portion of the fleet. The PM VERSS can measure PM emission factors for these high emitting vehicles on an individual basis. PM

Linear stochastic evaluation of tyre vibration due to tyre/road excitation

Science.gov (United States)

Rustighi, E.; Elliott, S. J.; Finnveden, S.; Gulyás, K.; Mócsai, T.; Danti, M.

2008-03-01

Tyre/road interaction is recognised as the main source of interior and exterior noise for velocities over the 40 km/h. In this paper, a three-dimensional (3D) elemental approach has been adopted to predict the stochastic tyre vibration and hence the interior and exterior noise due to this kind of excitation. The road excitation has been modelled from the spectral density of a common road profile, supposing the road to be an isotropic surface. A linear Winkler bedding connects the 3D model of the tyre with the ground. The exterior noise has been evaluated by an elemental calculation of the radiation matrix of the tyre deformed by the static load on a concrete road. The noise inside the vehicle has also been calculated, using the transfer functions from the force transmitted to the hub and the noise inside the vehicle, which have been computed by a FEM model of a common car body. The simple formulation allows much quicker calculation than traditional nonlinear approaches, and appears to give results consistent with available measurements, although the effects of tyre rotation and of the nonlinearities in the contact model are yet to be quantified, and the method requires further experimental validation before practical application.

Evaluation of mobile emissions contributions to Mexico City's emissions inventory using on-road and cross-road emission measurements and ambient data

Science.gov (United States)

Zavala, M.; Herndon, S. C.; Wood, E. C.; Onasch, T. B.; Knighton, W. B.; Marr, L. C.; Kolb, C. E.; Molina, L. T.

2009-09-01

Mobile emissions represent a significant fraction of the total anthropogenic emissions burden in the Mexico City Metropolitan Area (MCMA) and, therefore, it is crucial to use top-down techniques informed by on-road exhaust measurements to evaluate and improve traditional bottom-up official emissions inventory (EI) for the city. We present the measurements of on-road fleet-average emission factors obtained using the Aerodyne mobile laboratory in the MCMA in March 2006 as part of the MILAGRO/MCMA-2006 field campaign. A comparison of our on-road emission measurements with those obtained in 2003 using essentially the same measurement techniques and analysis methods indicates that, in the three year span, NO emission factors remain within the measured variability ranges whereas emission factors of aldehydes and aromatics species were reduced for all sampled driving conditions. We use a top-down fuel-based approach to evaluate the mobile emissions from the gasoline fleet estimated in the bottom-up official 2006 MCMA mobile sources. Within the range of measurement uncertainties, we found probable slight overpredictions of mean EI estimates on the order of 20-28% for CO and 14-20% for NO. However, we identify a probable EI discrepancy of VOC mobile emissions between 1.4 and 1.9; although estimated benzene and toluene mobile emissions in the inventory seem to be well within the uncertainties of the corresponding emissions estimates. Aldehydes mobile emissions in the inventory, however, seem to be underpredicted by factors of 3 for HCHO and 2 for CH3CHO. Our on-road measurement-based estimate of annual emissions of organic mass from PM1 particles suggests a severe underprediction (larger than a factor of 4) of PM2.5 mobile emissions in the inventory. Analyses of ambient CO, NOx and CO/NOx concentration trends in the MCMA indicate that the early morning ambient CO/NOx ratio has decreased at a rate of about 1.9 ppm/ppm/year over the last two decades due to reductions in CO

Assessment of elemental contamination in road dust using EDXRF

International Nuclear Information System (INIS)

Saradhi, I.V.; Sandeep, P.; Pandit, G.G.

2014-01-01

Road dust samples were collected in different locations of heavy traffic, medium traffic, express way and industrial areas of Mumbai. The concentrations of various elements (Mg, Al, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn and Pb) in road dust samples were analyzed using EDXRF. The average elemental profile of road dust in Mumbai was comparable with studies carried out in other countries with slight variations. The estimated geo accumulation indices and enrichment factors indicated moderate elemental contamination and enrichment of anthropogenic elements in road dust samples. Factor analysis of elemental data resolved four sources namely crustal, tyre wear, vehicular/industrial emissions and break wear. (author)

Properties of road unevenness inducing the kinematical excitation of vehicles

Directory of Open Access Journals (Sweden)

Kúdelčíková Mária

2017-01-01

Full Text Available The submitted paper is devoted to the mapping of the surface road profile and to the mathematical description of unevenness in one vehicle track. Its statistical parameters are analyzed and the classification of the road into a category based on power spectral density of unevenness is made.

[Prevention of road accidents in the road haulage field].

Science.gov (United States)

Rosso, G L; Zanelli, R; Corino, P; Bruno, S

2007-01-01

Every year many traffic accidents with fatal outcomes occur in our Country. According to the recent indications of the European Agency for Safety and Health at Work, the Piedmont region has financed the plan: Prevention of road accidents in the road haulage field. The aims of the plan are to stimulate transport companies to the target of road safety and to improve and enforce sanitary surveillance, in order to improve the safety on road haulage and to prevent traffic injuries. the plan foresees, over a period of two years, a few encounters with all the interested parties (companies, police forces, labour unions etc). During those encounters we have to give a questionnaire for evaluating the companies' knowledge about the problem and we have to choose a common plan with the aim of improving road safety. The Piedmont regional plan recalls the need to increase the attention to numerous and diversified hazards for safety on road haulage. It also imposes the choice of measures that include: risk assessment, health education, technical and environmental prevention, sanitary surveillance and clinical interventions (diagnosis and rehabilitation of occupational accidents).

High-resolution humidity profiles retrieved from wind profiler radar measurements

Science.gov (United States)

Saïd, Frédérique; Campistron, Bernard; Di Girolamo, Paolo

2018-03-01

The retrieval of humidity profiles from wind profiler radars has already been documented in the past 30 years and is known to be neither as straightforward and nor as robust as the retrieval of the wind velocity. The main constraint to retrieve the humidity profile is the necessity to combine measurements from the wind profiler and additional measurements (such as observations from radiosoundings at a coarser time resolution). Furthermore, the method relies on some assumptions and simplifications that restrict the scope of its application. The first objective of this paper is to identify the obstacles and limitations and solve them, or at least define the field of applicability. To improve the method, we propose using the radar capacity to detect transition levels, such as the top level of the boundary layer, marked by a maximum in the radar reflectivity. This forces the humidity profile from the free troposphere and from the boundary layer to coincide at this level, after an optimization of the calibration coefficients, and reduces the error. The resulting mean bias affecting the specific humidity profile never exceeds 0.25 g kg-1. The second objective is to explore the capability of the algorithm to retrieve the humidity vertical profiles for an operational purpose by comparing the results with observations from a Raman lidar.

Road icing forecasting and detecting system

Science.gov (United States)

Xu, Hongke; Zheng, Jinnan; Li, Peiqi; Wang, Qiucai

2017-05-01

Regard for the facts that the low accuracy and low real-time of the artificial observation to determine the road icing condition, and it is difficult to forecast icing situation, according to the main factors influencing the road-icing, and the electrical characteristics reflected by the pavement ice layer, this paper presents an innovative system, that is, ice-forecasting of the highway's dangerous section. The system bases on road surface water salinity measurements and pavement temperature measurement to calculate the freezing point of water and temperature change trend, and then predicts the occurrence time of road icing; using capacitance measurements to verdict the road surface is frozen or not; This paper expounds the method of using single chip microcomputer as the core of the control system and described the business process of the system.

Measurements of fusion product emission profiles in tokamaks

International Nuclear Information System (INIS)

Strachan, J.D.; Heidbrink, W.W.; Hendel, H.W.; Lovberg, J.; Murphy, T.J.; Nieschmidt, E.B.; Tait, G.D.; Zweben, S.J.

1986-11-01

The techniques and results of fusion product emission profile measurements are reviewed. While neutron source strength profile measurements have been attempted by several methods, neutron scattering is a limitation to the results. Profile measurements using charged fusion products have recently provided an alternative since collimation is much easier for the charged particles

Tyre-road contact using a particle-envelope surface model

Science.gov (United States)

Pinnington, Roger J.

2013-12-01

Determination of the contact forces is the central problem in all aspects of road-tyre interaction: i.e. noise, energy loss and friction. A procedure to find the contact forces under a rolling tyre is presented in four stages. First, the contact stiffness of a uniform peak array from indentations in the rubber tread, and also tyre carcass deflection, is described by some new simplified expressions. Second, a routine divides a single surface profile into equal search intervals, in which the highest peaks are identified. These are used to obtain the parameters for the interval, i.e. the mean envelope and the mean interval. The process is repeated at geometrically decreasing search intervals until the level of the data resolution, thereby describing the profile by a set of envelopes. The ‘strip profile’ ultimately used to describe the surface, is obtained by selecting the highest points across the profiles of one stone's width. The third stage is to combine the strip profile envelopes with the contact stiffness expressions, yielding the nonlinear stiffness-displacement, and force-displacement relationships for the chosen road-tyre combination. Finally the contact pressure distribution from a steady-state rolling tyre model is applied to the strip profile, via the force-displacement relationship, giving the local tyre displacements on the road texture. This displacement pattern is shown to be proportional to the time and space varying contact pressure, which then is incorporated into a wave equation for rolling contact.

Evaluation of a coupled dispersion and aerosol process model against measurements near a major road

Science.gov (United States)

Pohjola, M. A.; Pirjola, L.; Karppinen, A.; Härkönen, J.; Ketzel, M.; Kukkonen, J.

2007-02-01

A field measurement campaign was conducted near a major road "Itäväylä" in an urban area in Helsinki in 17-20 February 2003. Aerosol measurements were conducted using a mobile laboratory "Sniffer" at various distances from the road, and at an urban background location. Measurements included particle size distribution in the size range of 7 nm-10 μm (aerodynamic diameter) by the Electrical Low Pressure Impactor (ELPI) and in the size range of 3-50 nm (mobility diameter) by Scanning Mobility Particle Sizer (SMPS), total number concentration of particles larger than 3 nm detected by an ultrafine condensation particle counter (UCPC), temperature, relative humidity, wind speed and direction, driving route of the mobile laboratory, and traffic density on the studied road. In this study, we have compared measured concentration data with the predictions of the road network dispersion model CAR-FMI used in combination with an aerosol process model MONO32. The vehicular exhaust emissions, and atmospheric dispersion and transformation of fine and ultrafine particles was evaluated within the distance scale of 200 m (corresponding to a time scale of a couple of minutes). We computed the temporal evolution of the number concentrations, size distributions and chemical compositions of various particle size classes. The atmospheric dilution rate of particles is obtained from the roadside dispersion model CAR-FMI. Considering the evolution of total number concentration, dilution was shown to be the most important process. The influence of coagulation and condensation on the number concentrations of particle size modes was found to be negligible at this distance scale. Condensation was found to affect the evolution of particle diameter in the two smallest particle modes. The assumed value of the concentration of condensable organic vapour of 1012 molecules cm-3 was shown to be in a disagreement with the measured particle size evolution, while the modelling runs with the

Performance Assessment of Low-Noise Road Surfaces in the Leopoldo Project: Comparison and Validation of Different Measurement Methods

Directory of Open Access Journals (Sweden)

Gaetano Licitra

2015-01-01

Full Text Available In almost all urban contexts and in many extra-urban conurbations, where road traffic is the main noise pollution source, the use of barriers is not allowed. In these cases, low-noise road surfaces are the most used mitigation action together with traffic flow reduction. Selecting the optimal surface is only the first problem that the public administration has to face. In the second place, it has to consider the issue of assessing the efficacy of the mitigation action. The purpose of the LEOPOLDO project was to improve the knowledge in the design and the characterization of low-noise road surfaces, producing guidelines helpful to the public administrations. Several experimental road surfaces were tested. Moreover, several measurement methods were implemented aiming to select those that are suitable for a correct assessment of the pavement performances laid as mitigation planning. In this paper, the experience gained in the LEOPOLDO project will be described, focusing on both the measurement methods adopted to assess the performance of a low-noise road surface and the criteria by which the experimental results have to be evaluated, presenting a comparison of the obtained results and their monitoring along time.

The Dutch Bicycle Master Plan and road safety : measures to be taken.

NARCIS (Netherlands)

Noordzij, P.C. & Blokpoel, A.

1998-01-01

The Bicycle Master Plan was launched in 1990 and concluded in 1996. To mark its conclusion, a study was carried out to assess developments in road safety for cyclists. An overview of future measures was also compiled. Since 1950, there have been three broad periods: (1) 1950-1975: an increase in the

Road safety performance measures and AADT uncertainty from short-term counts.

Science.gov (United States)

Milligan, Craig; Montufar, Jeannette; Regehr, Jonathan; Ghanney, Bartholomew

2016-12-01

The objective of this paper is to enable better risk analysis of road safety performance measures by creating the first knowledge base on uncertainty surrounding annual average daily traffic (AADT) estimates when the estimates are derived by expanding short-term counts with the individual permanent counter method. Many road safety performance measures and performance models use AADT as an input. While there is an awareness that the input suffers from uncertainty, the uncertainty is not well known or accounted for. The paper samples data from a set of 69 permanent automatic traffic recorders in Manitoba, Canada, to simulate almost 2 million short-term counts over a five year period. These short-term counts are expanded to AADT estimates by transferring temporal information from a directly linked nearby permanent count control station, and the resulting AADT values are compared to a known reference AADT to compute errors. The impacts of five factors on AADT error are considered: length of short-term count, number of short-term counts, use of weekday versus weekend counts, distance from a count to its expansion control station, and the AADT at the count site. The mean absolute transfer error for expanded AADT estimates is 6.7%, and this value varied by traffic pattern group from 5% to 10.5%. Reference percentiles of the error distribution show that almost all errors are between -20% and +30%. Error decreases substantially by using a 48-h count instead of a 24-h count, and only slightly by using two counts instead of one. Weekday counts are superior to weekend counts, especially if the count is only 24h. Mean absolute transfer error increases with distance to control station (elasticity 0.121, p=0.001), and increases with AADT (elasticity 0.857, proad safety performance measures that use AADT as inputs. Analytical frameworks for such analysis exist but are infrequently used in road safety because the evidence base on AADT uncertainty is not well developed. Copyright �

Assessment on the methods of measuring the tyre-road contact patch stresses

Science.gov (United States)

Anghelache, G.; Moisescu, A.-R.; Buretea, D.

2017-08-01

The paper reviews established and modern methods for investigating tri-axial stress distributions in the tyre-road contact patch. The authors used three methods of measuring stress distributions: strain gauge method; force sensing technique; acceleration measurements. Four prototypes of instrumented pins transducers involving mentioned measuring methods were developed. Data acquisitions of the contact patch stresses distributions were performed using each transducer with instrumented pin. The results are analysed and compared, underlining the advantages and drawbacks of each method. The experimental results indicate that the three methods are valuable.

The IPERMOB System for Effective Real-Time Road Travel Time Measurement and Prediction

OpenAIRE

Martelli, Francesca; Renda, Maria Elena; Santi, Paolo

2010-01-01

Accurate, real-time measurement and estimation of road travel time is considered a central problem in the design of advanced Intelligent Transportation Systems. In particular, whether eective, real-time collection of travel time measurements in a urban area is possible is, to the best of our knowledge, still an open problem. In this paper, we introduce the IPERMOB system for efficient, real-time collection of travel time measurements in urban areas through vehicular networks. We demonstrate t...

Measurement and modelling of noise emission of road vehicles for use in prediction models

Energy Technology Data Exchange (ETDEWEB)

Jonasson, H.G.

2000-07-01

The road vehicle as sound source has been studied within a wide frequency range. Well defined measurements have been carried out on moving and stationary vehicles. Measurement results have been checked against theoretical simulations. A Nordtest measurement method to obtain input data for prediction methods has been proposed and tested in four different countries. The effective sound source of a car has its centre close to the nearest wheels. For trucks this centre seems to be closer to the centre of the car. The vehicle as sound source is directional both in the vertical and the horizontal plane. The difference between SEL and L{sub pFmax} during a pass-by varies with frequency. At low frequencies interference effects between correlated sources may be the problem. At high frequencies the directivity of tyre/road noise affects the result. The time when L{sub pFmax} is obtained varies with frequency. Thus traditional maximum measurements are not suitable for frequency band applications. The measurements support the fact that the tyre/road noise source is very low. Measurements on a stationary vehicle indicate that the engine source is also very low. Engine noise is screened by the body of the car. The ground attenuation, also at short distances, will be significant whenever we use low microphone positions and have some 'soft' ground in between. Unless all measurements are restricted to propagation over 'hard' surfaces only it is necessary to use rather high microphone positions. The Nordtest method proposed will yield a reproducibility standard deviation of 1-3 dB depending on frequency. High frequencies are more accurate. In order to get accurate results at low frequencies large numbers of vehicles are required. To determine the sound power level from pass-by measurement requires a proper source and propagation model. As these models may change it is recommended to measure and report both SEL and L{sub pFmax} normalized to a specified distance.

Development and enhancement of road lighting principles

Energy Technology Data Exchange (ETDEWEB)

Ekrias, A.

2010-07-01

The work starts with a short introduction concerning the history of road lighting, outlining the trends and changes that have taken place in road lighting research during the past century. The introduction is followed by a review of trends, directions, and problems in current road lighting research and practice. The following part of the work introduces an advanced approach to road lighting measurements and calculations, based on the use of an imaging luminance photometer and the Road LumiMeter v2.0 computer program. The work sets out to investigate the variations in the characteristics of the quality of the road lighting at the same pilot locations in relation to the calculation methods used. In the work mesopic visual performance and the effects of the spectral transmittance of the vehicle windshield on the visibility conditions of the driver are also analysed. The work continues with road lighting measurements in various weather conditions in order to study the effects of snowy and wet road surface conditions on road lighting luminances. The results show that in Finland, snowy conditions offer very good opportunities to save electricity without adversely affecting either the safety of driving or the quality of road lighting. The following measurements set out to investigate the contribution of halogen and high-intensity discharge headlights to road lighting and whether this has a conflicting effect on the luminance contrasts of various targets located on the road or at the side of the road. The results indicate that, in general, the use of vehicle headlights in the presence of road lighting reduces the luminance contrasts of targets. The work continues with road lighting visibility experiments which study the visibility of achromatic and coloured targets in MH lamp and HPS lamp installations. The results show that colours have a major effect on target visibility if the road is illuminated with a light source with adequate colour rendering properties. Finally

Traveling the Silk Road: A Measurement of a Large Anonymous Online Marketplace

Science.gov (United States)

2012-11-28

Silk Road, an anonymous, international online marketplace that operates as a Tor hidden service and uses Bitcoin as its exchange currency. We gather...analysis of Silk Road, an anonymous, international on- line marketplace that operates as a Tor hidden service and uses Bitcoin as its exchange currency. We...anonymity, Silk Road needs to also preserve payment anonymity. To that effect, Silk Road only supports Bitcoin (BTC, [30]) as a trading currency

Construction of Three-Dimensional Road Surface and Application on Interaction between Vehicle and Road

Directory of Open Access Journals (Sweden)

Lu Yongjie

2018-01-01

Full Text Available The quantitative description is given to three-dimensional micro and macro self-similar characteristics of road surface from the perspective of fractal geometry using FBM stochastic midpoint displacement and diamond-square algorithm in conjunction with fractal characteristics and statistical characteristics of standard pavement determined by estimation method of box-counting dimension. The comparative analysis between reconstructed three-dimensional road surface spectrum and theoretical road surface spectrum and correlation coefficient demonstrate the high reconstruction accuracy of fractal reconstructed road spectrum. Furthermore, the bump zone is taken as an example to reconstruct a more arbitrary 3D road model through isomorphism of special road surface with stochastic road surface model. Measurement is taken to assume the tire footprint on road surface to be a rectangle, where the pressure distribution is expressed with mean stiffness, while the contact points in the contact area are replaced with a number of springs. Two-DOF vehicle is used as an example to analyze the difference between three-dimensional multipoint-and-plane contact and traditional point contact model. Three-dimensional road surface spectrum provides a more accurate description of the impact effect of tire on road surface, thereby laying a theoretical basis for studies on the dynamical process of interaction of vehicle-road surface and the road friendliness.

Environmental radiation monitoring: mobile gamma dose rate measurements along Mumbai-Hyderabad rail route and Hyderabad city roads

International Nuclear Information System (INIS)

Divkar, J.K.; Padmanabhan, N.; Chaudhury, Probal; Pradeepkumar, K.S.; Pujari, R.N.; Dogra, Santosh; Sharma, D.N.; Rajagopalan, S.; Srivastava, G.K.

2005-01-01

Environmental Radiation monitoring based on gamma dose rate logging on a mobile platform integrated with real time position from a Global Positioning System is an effective tool to acquire dose rate profile and generate radiological map of any geographical region. The microcontroller based dose rate data acquisition system capable of storing the acquired data and transferring to an attached laptop/PC and providing a graphical illustration of relative variations in gamma background can also be used for quick assessment of environmental radiological impact assessment. This paper describes the methodology and results of the environmental gamma dose rate monitoring surveys carried out: (i) on Mumbai-Hyderabad rail route with the systems installed in the trains guard's room and (ii) Hyderabad city roads with systems installed in a monitoring van. The results indicate significant difference in the gamma background measured along the rail route between Mumbai-Hyderabad and in the radiological map generated after the Hyderabad city survey. (author)

Road accident rates: strategies and programmes for improving road traffic safety.

Science.gov (United States)

Goniewicz, K; Goniewicz, M; Pawłowski, W; Fiedor, P

2016-08-01

Nowadays, the problem of road accident rates is one of the most important health and social policy issues concerning the countries in all continents. Each year, nearly 1.3 million people worldwide lose their life on roads, and 20-50 million sustain severe injuries, the majority of which require long-term treatment. The objective of the study was to identify the most frequent, constantly occurring causes of road accidents, as well as outline actions constituting a basis for the strategies and programmes aiming at improving traffic safety on local and global levels. Comparative analysis of literature concerning road safety was performed, confirming that although road accidents had a varied and frequently complex background, their causes have changed only to a small degree over the years. The causes include: lack of control and enforcement concerning implementation of traffic regulation (primarily driving at excessive speed, driving under the influence of alcohol, and not respecting the rights of other road users (mainly pedestrians and cyclists), lack of appropriate infrastructure and unroadworthy vehicles. The number of fatal accidents and severe injuries, resulting from road accidents, may be reduced through applying an integrated approach to safety on roads. The strategies and programmes for improving road traffic should include the following measures: reducing the risk of exposure to an accident, prevention of accidents, reduction in bodily injuries sustained in accidents, and reduction of the effects of injuries by improvement of post-accident medical care.

Tire use and road safety : background to policy recommendations for new EU measures

NARCIS (Netherlands)

Jansen, S.; Schmeitz, A.J.C.; Akkermans, L.

2015-01-01

TNO and TML performed a study commissioned by the European Commission regarding what measures on a European level can be taken in relation to the use of tyres to improve road safety. The study considers the use of Winter tyres, tread depth requirements, tyre inflation pressure maintenance and tyre

Characterization, Exposure Measurement and Control for Nanoscale Particles in Workplaces and on the Road

International Nuclear Information System (INIS)

Wang Jing; Pui, David Y H

2011-01-01

The amount of engineered nanoparticles is increasing at a rapid rate and more concerns are being raised about the occupational health and safety of nanoparticles in the workplace, and implications of nanotechnology on the environment and living systems. At the same time, diesel engine emissions are one of the serious air pollution sources in urban area. Ultrafine particles on the road can result in harmful effects on the health of drivers and passengers. Research on characterization, exposure measurement and control is needed to address the environmental, health and safety issues of nanoscale particles. We present results of our studies on airborne particles in workplaces and on the road.

Characterization, Exposure Measurement and Control for Nanoscale Particles in Workplaces and on the Road

Energy Technology Data Exchange (ETDEWEB)

Wang Jing [Institute of Environmental Engineering, ETH Zuerich, 8093 (Switzerland); Pui, David Y H, E-mail: jing.wang@ifu.baug.ethz.ch [Particle Technology Laboratory, University of Minnesota, 55414 (United States)

2011-07-06

The amount of engineered nanoparticles is increasing at a rapid rate and more concerns are being raised about the occupational health and safety of nanoparticles in the workplace, and implications of nanotechnology on the environment and living systems. At the same time, diesel engine emissions are one of the serious air pollution sources in urban area. Ultrafine particles on the road can result in harmful effects on the health of drivers and passengers. Research on characterization, exposure measurement and control is needed to address the environmental, health and safety issues of nanoscale particles. We present results of our studies on airborne particles in workplaces and on the road.

Characteristics of On-road Diesel Vehicles: Black Carbon Emissions in Chinese Cities Based on Portable Emissions Measurement.

Science.gov (United States)

Zheng, Xuan; Wu, Ye; Jiang, Jingkun; Zhang, Shaojun; Liu, Huan; Song, Shaojie; Li, Zhenhua; Fan, Xiaoxiao; Fu, Lixin; Hao, Jiming

2015-11-17

Black carbon (BC) emissions from heavy-duty diesel vehicles (HDDVs) are rarely continuously measured using portable emission measurement systems (PEMSs). In this study, we utilize a PEMS to obtain real-world BC emission profiles for 25 HDDVs in China. The average fuel-based BC emissions of HDDVs certified according to Euro II, III, IV, and V standards are 2224 ± 251, 612 ± 740, 453 ± 584, and 152 ± 3 mg kg(-1), respectively. Notably, HDDVs adopting mechanical pump engines had significantly higher BC emissions than those equipped with electronic injection engines. Applying the useful features of PEMSs, we can relate instantaneous BC emissions to driving conditions using an operating mode binning methodology, and the average emission rates for Euro II to Euro IV diesel trucks can be constructed. From a macroscopic perspective, we observe that average speed is a significant factor affecting BC emissions and is well correlated with distance-based emissions (R(2) = 0.71). Therefore, the average fuel-based and distance-based BC emissions on congested roads are 40 and 125% higher than those on freeways. These results should be taken into consideration in future emission inventory studies.

New optimization strategies of pavement maintenance: A case study for national road network in Indonesia using integrated road management system

Science.gov (United States)

Hamdi, Hadiwardoyo, Sigit P.; Correia, A. Gomes; Pereira, Paulo

2017-06-01

A road network requires timely maintenance to keep the road surface in good condition onward better services to improve accessibility and mobility. Strategies and maintenance techniques must be chosen in order to maximize road service level through cost-effective interventions. This approach requires an updated database, which the road network in Indonesia is supported by a manual and visual survey, also using NAASRA profiler. Furthermore, in this paper, the deterministic model of deterioration was used. This optimization model uses life cycle cost analysis (LCCA), applied in an integrated manner, using IRI indicator, and allows determining the priority of treatment, type of treatment and its relation to the cost. The purpose of this paper was focussed on the aspects of road maintenance management, i.e., maintenance optimization models for different levels of traffic and various initial of road distress conditions on the national road network in Indonesia. The implementation of Integrated Road Management System (IRMS) can provide a solution to the problem of cost constraints in the maintenance of the national road network. The results from this study found that as the lowest as agency cost, it will affect the increasing of user cost. With the achievement of the target plan scenario Pl000 with initial value IRI 2, it was found that the routine management throughout the year and in early reconstruction and periodic maintenance with a 30 mm thick overlay, will simultaneously provide a higher net benefit value and has the lowest total cost of transportation.

Determinants of injuries and Road Traffic Accidents amongst service personnel in a large Defence station.

Science.gov (United States)

Neelakantan, Anand; Kotwal, Brig Atul; Ilankumaran, Mookkiah

2017-07-01

Injuries are assuming epidemic proportions globally; and in India. Also, previous decade witnessed carnage on Indian roads, with nearly 12 lakh people killed and 55 lakhs disabled in road crashes. The trend in Armed Forces is reflective of the aforesaid patterns. Behaviour and socio-demographic background of the victims are significant determinants of injuries and road accidents. Community-based epidemiological information on these aspects is envisaged to contribute in their preventive strategy. Towards this direction, the present study was conducted with aim to generate socio-behavioural profile of injuries and Road Traffic Accidents (RTAs) amongst service personnel in a large defence station; and to evaluate their determinants. A cross sectional descriptive study was carried out among 796 Naval personnel onboard warships in large Naval station. Data on socio-behavioural aspects and determinants of injuries and road accidents was collected using a pre-validated questionnaire; and by scrutiny of relevant records. Data was analysed using MSExcel, Epi-info and SPSS 17. Young and middle-aged persons were predominantly involved in injuries and road accidents. Two-wheeler users sustained maximum road accidents. Human factor was a significant determinant in RTAs and injuries. A majority of victims admitted that human factors were the predominant cause of road accidents; and opined that the events were preventable. Age-specific Behavioural Change Communication strategies aimed at refining user outlook are imperative; tailored to sociodemographic milieu of user/victim. Incorporation of a dynamic feedback/reporting mechanism, creation of 'armed forces-specific road safety and injury prevention policy' and safety audits on injuries and road crashes are measures in this direction.

Road Infrastructure Safety Management in Poland

Science.gov (United States)

Budzynski, Marcin; Jamroz, Kazimierz; Kustra, Wojciech; Michalski, Lech; Gaca, Stanislaw

2017-10-01

The objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be identified, assessed and mitigated. Road transport safety is significantly less developed than that of rail, water and air transport. The average individual risk of being a fatality in relation to the distance covered is thirty times higher in road transport that in the other modes. This is mainly because the different modes have a different approach to safety management and to the use of risk management methods and tools. In recent years Poland has had one of the European Union’s highest road death numbers. In 2016 there were 3026 fatalities on Polish roads with 40,766 injuries. Protecting road users from the risk of injury and death should be given top priority. While Poland’s national and regional road safety programmes address this problem and are instrumental in systematically reducing the number of casualties, the effects are far from the expectations. Modern approaches to safety focus on three integrated elements: infrastructure measures, safety management and safety culture. Due to its complexity, the process of road safety management requires modern tools to help with identifying road user risks, assess and evaluate the safety of road infrastructure and select effective measures to improve road safety. One possible tool for tackling this problem is the risk-based method for road infrastructure safety management. European Union Directive 2008/96/EC regulates and proposes a list of tools for managing road infrastructure safety. Road safety tools look at two criteria: the life cycle of a road structure and the process of risk management. Risk can be minimized through the application of the proposed interventions during design process as reasonable. The proposed methods of risk management bring together two stages: risk assessment and risk response occurring within the analyzed road structure (road network, road

EFFECT OF A ROAD SAFETY EDUCATION INTERVENTION ON ROAD SAFETY KNOWLEDGE OF UNIVERSITY DRIVERS IN IBADAN, NIGERIA.

Science.gov (United States)

Olumide, A O; Owoaje, E T

2016-06-01

It is essential for drivers employed in the formal sector to have good knowledge of road safety in order to safeguard their lives and those of the staff they are employed to drive. The study was conducted to determine the effect of a road safety education intervention on road safety knowledge of drivers employed in the University of Ibadan, Nigeria. A quasi-experimental study of 98 intervention and 78 control drivers selected using a cluster sampling technique was conducted. The intervention comprised a two-day training on road safety and first aid. The drivers' knowledge of road safety was measured at baseline, immediately and 4-months post-intervention. Aggregate scores of road safety knowledge were computed giving minimum and maximum obtainable scores of 0 and 16 respectively. Change in mean scores over the three measurement periods was assessed using Repeated Measures Analysis of Variance (ANOVA). Independent t-test was used to compare the scores between intervention and control drivers at each of the assessment periods. Twenty-nine drivers did not complete the study (attrition rate = 16.5%). At baseline, mean road safety knowledge scores for the intervention and control drivers were 12.7±2.2 and 12.9± 2.3 (p = 0.510) respectively. Immediately and four months post intervention, the scores of the intervention drivers were 13.8±1.9 and 12.8±1.6; while scores for the controls were 13.3±2.0 and 13.2±1.8. Repeated measures ANOVA revealed that the increase in knowledge over the three assessment periods was not statistically significant. The intervention resulted in an initial increase in road safety knowledge of the intervention drivers. However, this was not sustained to the forth month post-intervention. This finding suggests periodic refresher trainings to sustain the knowledge acquired.

Trend road safety measures : international course on transportation and road engineering in developing countries. Two-year postgraduate Diploma and M.Sc. programme.

NARCIS (Netherlands)

1991-01-01

This course focuses mainly on traffic and transport in developing countries, and deals primarily with matters of infrastructure. Road safety and road safety problems are closely related to the construction and operation of the road network. (See also C 1341 - C1346).

Density and moisture measurements by nuclear method and its application to compaction control in road construction

International Nuclear Information System (INIS)

Mohd Azmi Ismail

1994-01-01

The application of nuclear technique in civil engineering sector which emphasises on the in-situ density and moisture measurements of soil in road construction is discussed. The nuclear density-moisture gauge utilises both gamma-rays and neutrons for the determination of the density and moisture content, respectively. The knowledge on the density and moisture content will be used to evaluate the degree of compaction of the compacted layers. The technique offers not only a fast and non-destructive measurement but it is also accurate, economical and repeatable. A calibration equation which is stored in the built-in microprocessor is applicable for any type of soil. Corrections for the interferences from needless gamma-rays produced as a result of thermal neutrons interaction with certain nuclei for the density measurement and effects of hydrogen other than absorbed water for the moisture measurement are considered in the equation. This paper describes briefly the theory and the characteristics of the nuclear gauge and its application in road construction work

Flood-inundation maps for the Withlacoochee River From Skipper Bridge Road to St. Augustine Road, within the City of Valdosta, Georgia, and Lowndes County, Georgia

Science.gov (United States)

Musser, Jonathan W.

2018-01-31

Digital flood-inundation maps for a 12.6-mile reach of the Withlacoochee River from Skipper Bridge Road to St. Augustine Road (Georgia State Route 133) were developed to depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the U.S. Geological Survey (USGS) streamgage at Withlacoochee River at Skipper Bridge Road, near Bemiss, Ga. (023177483). Real-time stage information from this streamgage can be used with these maps to estimate near real-time areas of inundation. The forecasted peak-stage information for the USGS streamgage at Withlacoochee River at Skipper Bridge Road, near Bemiss, Ga. (023177483), can be used in conjunction with the maps developed for this study to show predicted areas of flood inundation.A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers Hydrologic Engineer-ing Center’s River Analysis System (HEC–RAS) software for the Withlacoochee River and was used to compute flood profiles for a 12.6-mile reach of the Withlacoochee River. The hydraulic model was then used to simulate 23 water-surface profiles at 1.0-foot (ft) intervals at the Withlacoochee River near the Bemiss streamgage. The profiles ranged from the National Weather Service action stage of 10.7 ft, which is 131.0 ft above the North American Vertical Datum of 1988 (NAVD 88), to a stage of 32.7 ft, which is 153.0 ft above NAVD 88. The simulated water-surface profiles were then combined with a geographic information system digital elevation model—derived from light detection and ranging (lidar) data having a 4.0-ft horizontal resolution—to delineate the area flooded at each 1.0-ft interval of stream stage.

The road safety audit and road safety inspection.

NARCIS (Netherlands)

2007-01-01

A road safety audit (RSA) and a road safety inspection (RSI) are used to test the safety level of the road infrastructure. The RSA tests the design of new roads or the reconstruction of existing roads, whereas the RSI is used for testing existing roads. An RSA, therefore, aims to 'improve' the road

Measured and modelled concentrations and vertical profiles of airborne particulate matter within the boundary layer of a street canyon

International Nuclear Information System (INIS)

Colls, J.J.; Micallef, A.

1999-01-01

Concentrations and vertical profiles of various fractions of airborne particulate matter (suspended particulate matter (SPM), PM 10 and PM 2.5 ) have been measured over the first three metres from ground in a street canyon. Measurements were carried out using automated near real-time apparatus called the Kinetic Sequential Sampling (KSS) system. KSS system is essentially an electronically-controlled lift carrying a real-time particle monitor for sampling air sequentially, at different heights within the breathing zone, which includes all heights within the surface layer of a street canyon at which people may breathe. Data is automatically logged at the different receptor levels, for the determination of the average vertical concentration profile of airborne particulate matter. For measuring the airborne particle concentration, a Grimm Dust Monitor 1.104/5 was used. The recorded data also allows for time series analysis of airborne particulate matter concentration at different heights. Time series data and hourly-average vertical concentration profiles in the boundary layer of the confines of a street are thought to be mainly determined by traffic emissions and traffic associated processes. Hence the measured data were compared with results of a street canyon emission-dispersion model in time and space. This Street Level Air Quality (SLAQ) model employs the plume-box technique and includes modules for simulating vehicle-generated effects such as thermally- and mechanically-generated turbulence and resuspension of road dust. Environmental processes, such as turbulence resulting from surface sensible heat and the formation of sulphate aerosol from sulphur dioxide exhaust emissions, are taken into account. The paper presents an outline description of the measuring technique and model used, and a comparison of the measured and modelled data

A Study on the Influence of Speed on Road Roughness Sensing: The SmartRoadSense Case

Directory of Open Access Journals (Sweden)

Giacomo Alessandroni

2017-02-01

Full Text Available SmartRoadSense is a crowdsensing project aimed at monitoring the conditions of the road surface. Using the sensors of a smartphone, SmartRoadSense monitors the vertical accelerations inside a vehicle traveling the road and extracts a roughness index conveying information about the road conditions. The roughness index and the smartphone GPS data are periodically sent to a central server where they are processed, associated with the specific road, and aggregated with data measured by other smartphones. This paper studies how the smartphone vertical accelerations and the roughness index are related to the vehicle speed. It is shown that the dependence can be locally approximated with a gamma (power law. Extensive experimental results using data extracted from SmartRoadSense database confirm the gamma law relationship between the roughness index and the vehicle speed. The gamma law is then used for improving the SmartRoadSense data aggregation accounting for the effect of vehicle speed.

Multispectral Image Road Extraction Based Upon Automated Map Conflation

Science.gov (United States)

Chen, Bin

Road network extraction from remotely sensed imagery enables many important and diverse applications such as vehicle tracking, drone navigation, and intelligent transportation studies. There are, however, a number of challenges to road detection from an image. Road pavement material, width, direction, and topology vary across a scene. Complete or partial occlusions caused by nearby buildings, trees, and the shadows cast by them, make maintaining road connectivity difficult. The problems posed by occlusions are exacerbated with the increasing use of oblique imagery from aerial and satellite platforms. Further, common objects such as rooftops and parking lots are made of materials similar or identical to road pavements. This problem of common materials is a classic case of a single land cover material existing for different land use scenarios. This work addresses these problems in road extraction from geo-referenced imagery by leveraging the OpenStreetMap digital road map to guide image-based road extraction. The crowd-sourced cartography has the advantages of worldwide coverage that is constantly updated. The derived road vectors follow only roads and so can serve to guide image-based road extraction with minimal confusion from occlusions and changes in road material. On the other hand, the vector road map has no information on road widths and misalignments between the vector map and the geo-referenced image are small but nonsystematic. Properly correcting misalignment between two geospatial datasets, also known as map conflation, is an essential step. A generic framework requiring minimal human intervention is described for multispectral image road extraction and automatic road map conflation. The approach relies on the road feature generation of a binary mask and a corresponding curvilinear image. A method for generating the binary road mask from the image by applying a spectral measure is presented. The spectral measure, called anisotropy-tunable distance (ATD

The prediction of BRDFs from surface profile measurements

International Nuclear Information System (INIS)

Church, E.L.; Takacs, P.Z.; Leonard, T.A.

1989-01-01

This paper discusses methods of predicting the BRDF of smooth surfaces from profile measurements of their surface finish. The conversion of optical profile data to the BRDF at the same wavelength is essentially independent of scattering models, while the conversion of mechanical measurements, and wavelength scaling in general, are model dependent. Procedures are illustrated for several surfaces, including two from the recent HeNe BRDF round robin, and results are compared with measured data. Reasonable agreement is found except for surfaces which involve significant scattering from isolated surface defects which are poorly sampled in the profile data

Improved performance evaluation of road pavements by using measured tyre loading

CSIR Research Space (South Africa)

Maina, JW

2008-11-01

Full Text Available This paper presents evaluation of road pavement response under the loading of typical dual and single truck tyre configurations. Locally developed Stress-In-Motion (SIM) technology was used to quantify three-dimensional (3D) shapes of the tyre road...

Contractors Road Heavy Equipment Area SWMU 055 Corrective Measures Implementation Progress Report

Science.gov (United States)

Dorman, Lane

2015-01-01

This Corrective Measures Implementation (CMI) Progress Report, Revision 1, for Contractor's Road Heavy Equipment (CRHE) Area Solid Waste Management Unit (SWMU) Number 055 was prepared by Geosyntec Consultants (Geosyntec) for the National Aeronautics and Space Administration (NASA) under contract number NNK09CA02B, Delivery Order NNK09CA62D and Project Number PCN ENV-2324. This CMI Progress Report documents: (i) activities conducted as part of supplemental assessment activities completed from June 2009 through November 2014; (ii) Engineering Evaluation (EE) Advanced Data Packages (ADPs); and (iii) recommendations for future activities related to corrective measures at the Site.

Characterizing near-road air pollution using local-scale emission and dispersion models and validation against in-situ measurements

Science.gov (United States)

Wang, An; Fallah-Shorshani, Masoud; Xu, Junshi; Hatzopoulou, Marianne

2016-10-01

Near-road concentrations of nitrogen dioxide (NO2), a known marker of traffic-related air pollution, were simulated along a busy urban corridor in Montreal, Quebec using a combination of microscopic traffic simulation, instantaneous emission modeling, and air pollution dispersion. In order to calibrate and validate the model, a data collection campaign was designed. For this purpose, measurements of NO2 were conducted mid-block along four segments of the corridor throughout a four-week campaign conducted between March and April 2015. The four segments were chosen to be consecutive and yet exhibiting variability in road configuration and built environment characteristics. Roadside NO2 measurements were also paired with on-site and fixed-station meteorological data. In addition, traffic volumes, composition, and routing decisions were collected using video-cameras located at upstream and downstream intersections. Dispersion of simulated emissions was conducted for eight time slots and under a range of meteorological conditions using three different models with vastly different dispersion algorithms (OSPM, CALINE 4, and SIRANE). The three models exhibited poor correlation with near-road NO2 concentrations and were better able to simulate average concentrations occurring along the roadways rather than the range of concentrations measured under diverse meteorological and traffic conditions. As hypothesized, the model SIRANE that can handle a street canyon configuration was the most sensitive to the built environment especially to the presence of tall buildings around the road. In contrast, CALINE exhibited the lowest sensitivity to the built environment.

Evolution of tyre/road noise research in India: Investigations using statistical pass-by method and noise trailer

Directory of Open Access Journals (Sweden)

Vivek Khan

2018-05-01

Full Text Available The objective of this research study was to investigate and analyze the acoustical characteristics of asphalt concrete and cement concrete surface types by two noise measurement techniques: statistical pass-by (SPB and Close Proximity (CPX methods. A noise trailer was devised and manufactured as part of the CPX methodology to evaluate tyre/pavement noise interaction at source. Two national highway test sections covering over 11 km of asphalt and cement concrete surfaces were selected to carry out the noise measurements, and the effects of vehicle speeds and/or sizes on the overall noise profiles were investigated. The major contribution of this first of its kind study in India was the utilization of sophisticated tools and techniques to measure the tyre/pavement interaction noise at source through CPX, which helped correlate the influence of road surfaces on the generation of overall road traffic noise using SPB technique. The SPB method noise profiles revealed that the noise pressure levels increased with increasing vehicle speeds and weights. The noise trailer CPX findings corroborated the results obtained from the SPB method in that cement concrete surface produced a higher noise at source than that of the asphalt concrete surface by about 5 dBA. Further, there was about 5 dBA differential in noise between SPB and CPX methods for cement concrete pavement sections; also, there was about 10 dBA differential in noise between the two methods for asphalt concrete pavement stretches. Keywords: Tyre/road noise, Statistical pass-by, Close proximity, Noise trailer, Asphalt concrete, Cement concrete

Experimental study of tyre/road contact forces in rolling conditions for noise prediction

Science.gov (United States)

Cesbron, Julien; Anfosso-Lédée, Fabienne; Duhamel, Denis; Ping Yin, Hai; Le Houédec, Donatien

2009-02-01

This paper deals with the experimental study of dynamical tyre/road contact for noise prediction. In situ measurements of contact forces and close proximity noise levels were carried out for a slick tyre rolling on six different road surfaces between 30 and 50 km/h. Additional texture profiles of the tested surfaces were taken on the wheel track. Normal contact stresses were measured at a sampling frequency of 10752 Hz using a line of pressure sensitive cells placed both along and perpendicular to the rolling direction. The contact areas obtained during rolling were smaller than in static conditions. This is mainly explained by the dynamical properties of tyre compounds, like the viscoelastic behaviour of the rubber. Additionally the root-mean-square of the resultant contact forces at various speeds was in the same order for a given road surface, while their spectra were quite different. This is certainly due to a spectral influence of bending waves propagating in the tyre during rolling, especially when the wavelength is small in comparison with the size of the contact patch. Finally, the levels of contact forces and close proximity noise measured at 30 km/h were correlated. Additional correlations with texture levels were performed. The results show that the macro-texture generates contact forces linearly around 800 Hz and consequently noise levels between 500 and 1000 Hz via the vibrations transmitted to the tyre.

Using CART to segment road images

Science.gov (United States)

Davies, Bob; Lienhart, Rainer

2006-01-01

The 2005 DARPA Grand Challenge is a 132 mile race through the desert with autonomous robotic vehicles. Lasers mounted on the car roof provide a map of the road up to 20 meters ahead of the car but the car needs to see further in order to go fast enough to win the race. Computer vision can extend that map of the road ahead but desert road is notoriously similar to the surrounding desert. The CART algorithm (Classification and Regression Trees) provided a machine learning boost to find road while at the same time measuring when that road could not be distinguished from surrounding desert.

Mine haul road fugitive dust emission and exposure characterisation

Energy Technology Data Exchange (ETDEWEB)

Thompson, R.J.; Visser, A.T. [University of Pretoria, Pretoria (South Africa). Dept. of Mining Engineering

2001-03-01

Excessive dust generation from mine haul roads is a problem common to most surface coal mining operations. Optimal wearing course material selection parameters reduce, but do not toally eliminate the potential to produce dust. For existing operations, which may not have optimally designed and maintained roads, the problem of identifying the haul road dust defect, quantifying its impact on both safety and health and assigning priorities within the constraints of limited capital and manpower is problematic. This is reflected in the fact that most surface mine operators agree dust-free roads are desirable, but find it difficult to translate this into cost-effective betterment activities. The aim of this paper is to describe fugitive dust emission and exposure characteristics associated with ultra-heavy mine haul trucks running on unpaved mine haul roads. Models are described which enable mines to assess the likely dustiness of their chosen haul road material as a function of surface loading of fines, traffic types and volume, together with various material parameters. By combining these models with the results of quantitative exposure profiling, a mine can, in conjunction with the assessment, determine the most cost- and safety-effective haul road dust management strategy. 18 refs., 10 figs., 2 tabs.

Doping profile measurement on textured silicon surface

Science.gov (United States)

Essa, Zahi; Taleb, Nadjib; Sermage, Bernard; Broussillou, Cédric; Bazer-Bachi, Barbara; Quillec, Maurice

2018-04-01

In crystalline silicon solar cells, the front surface is textured in order to lower the reflection of the incident light and increase the efficiency of the cell. This texturing whose dimensions are a few micrometers wide and high, often makes it difficult to determine the doping profile measurement. We have measured by secondary ion mass spectrometry (SIMS) and electrochemical capacitance voltage profiling the doping profile of implanted phosphorus in alkaline textured and in polished monocrystalline silicon wafers. The paper shows that SIMS gives accurate results provided the primary ion impact angle is small enough. Moreover, the comparison between these two techniques gives an estimation of the concentration of electrically inactive phosphorus atoms.

Mixing height measurements from UHF wind profiling radar

Energy Technology Data Exchange (ETDEWEB)

Angevine, W.M.; Grimsdell, A.W. [CIRES, Univ. of Colorado, and NOAA Aeronomy Lab., Boulder, Colorado (United States)

1997-10-01

Mixing height in convective boundary layers can be detected by wind profiling radars (profilers) operating at or near 915 MHZ. We have made such measurements in a variety of settings including Alabama in 1992; Nova Scotia, Canada, during the North Atlantic Regional Experiment (NARE) 1993; Tennessee during the Southern Oxidant Study (SOS) 1994; near a 450 m tower in Wisconsin in 1995; and extensively in Illinois during the Flatland95, `96, and `97 experiments, as well as continuous operations at the Flatland Atmospheric Observatory. Profiler mixing height measurements, like all measurements, are subject to some limitations. The most important of these are due to rainfall, minimum height, and height resolution. Profilers are very sensitive to rain, which dominates the reflectivity and prevents the mixing height from being detected. Because the best height resolution is currently 60 m and the minimum height is 120-150 m AGL, the profiler is not suited for detecting mixing height in stable or nocturnal boundary layers. Problems may also arise in very dry or cold environments. (au) 12 refs.

Techniques for intense-proton-beam profile measurements

International Nuclear Information System (INIS)

Gilpatrick, J.D.

1998-01-01

In a collaborative effort with industry and several national laboratories, the Accelerator Production of Tritium (APT) facility and the Spallation Neutron Source (SNS) linac are presently being designed and developed at Los Alamos National Laboratory (LANL). The APT facility is planned to accelerate a 100-mA H + cw beam to 1.7 GeV and the SNS linac is planned to accelerate a 1- to 4-mA-average, H - , pulsed-beam to 1 GeV. With typical rms beam widths of 1- to 3-mm throughout much of these accelerators, the maximum average-power densities of these beams are expected to be approximately 30- and 1-MW-per-square millimeter, respectively. Such power densities are too large to use standard interceptive techniques typically used for acquisition of beam profile information. This paper summarizes the specific requirements for the beam profile measurements to be used in the APT, SNS, and the Low Energy Development Accelerator (LEDA)--a facility to verify the operation of the first 20-MeV section of APT. This paper also discusses the variety of profile measurement choices discussed at a recent high-average-current beam profile workshop held in Santa Fe, NM, and will present the present state of the design for the beam profile measurements planned for APT, SNS, and LEDA

Factors contributing to amphibian road mortality in a wetland

Directory of Open Access Journals (Sweden)

Haijun GU, Qiang DAI, Qian WANG, Yuezhao WANG

2011-12-01

Full Text Available To understand road characteristics and landscape features associated with high road mortality of amphibians in Zoige Wetland National Nature Reserve, we surveyed road mortality along four major roads after rainfall in May and September 2007. Road mortality of three species, Rana kukunoris, Nanorana pleskei and Bufo minshanicus, was surveyed across 225 transects (115 in May and 110 in September. Transects were 100 m long and repeated every two kilometers along the four major roads. We used model averaging to assess factors that might determine amphibian road mortality. We recorded an average of 24.6 amphibian road mortalities per kilometer in May and 19.2 in September. Among road characteristics, road width was positively associated with road morality for R. kukunori and B. minshanicus. Traffic volume also increased the road mortality of B. minshanicus in September. Of the landscape features measured, area proportions of three types of grassland (wet, mesic and dry within 1 km of the roads, particularly that of wet grassland, significantly increased road mortality for R. kukunori and total mortality across all three species. To most effectively reduce road mortality of amphibians in the Zoige wetlands, we suggest better road design such as avoiding wet grasslands, minimizing road width, underground passes and traffic control measures. The implementation of public transit in the area would reduce traffic volume, and hence mortality [Current Zoology 57 (6: 768–774, 2011].

Parameterizing road construction in route-based road weather models: can ground-penetrating radar provide any answers?

International Nuclear Information System (INIS)

Hammond, D S; Chapman, L; Thornes, J E

2011-01-01

A ground-penetrating radar (GPR) survey of a 32 km mixed urban and rural study route is undertaken to assess the usefulness of GPR as a tool for parameterizing road construction in a route-based road weather forecast model. It is shown that GPR can easily identify even the smallest of bridges along the route, which previous thermal mapping surveys have identified as thermal singularities with implications for winter road maintenance. Using individual GPR traces measured at each forecast point along the route, an inflexion point detection algorithm attempts to identify the depth of the uppermost subsurface layers at each forecast point for use in a road weather model instead of existing ordinal road-type classifications. This approach has the potential to allow high resolution modelling of road construction and bridge decks on a scale previously not possible within a road weather model, but initial results reveal that significant future research will be required to unlock the full potential that this technology can bring to the road weather industry. (technical design note)

Association between light absorption measurements of PM2.5 and distance from heavy traffic roads in the Mexico City metropolitan area.

Science.gov (United States)

Cortez-Lugo, Marlene; Escamilla-Núñez, Consuelo; Barraza-Villarreal, Albino; Texcalac-Sangrador, José Luis; Chow, Judith; Watson, John; Hernández-Cadena, Leticia; Romieu, Isabelle

2013-04-01

To study the relationship between light absorption measurements of PM2.5 at various distances from heavy traffic roads and diesel vehicle counts in Mexico City. PM2.5 samples were obtained from June 2003-June 2005 in three MCMA regions. Light absorption (b abs) in a subset of PM2.5 samples was determined. We evaluated the effect of distance and diesel vehicle counts to heavy traffic roads on PM2.5 b abs using generalized estimating equation models. Median PM2.5 b abs measurements significantly decrease as distance from heavy traffic roads increases (proads. Our model predicts that PM2.5 b abs measurements would increase by 20% (CI95% 3-38) as the hourly heavy diesel vehicle count increases by 150 per hour. PM2.5 b abs measurements are significantly associated with distance from motorways and traffic density and therefore can be used to assess human exposure to traffic-related emissions.

Detection of the local sliding in the tyre-road contact by measuring vibrations on the inner liner of the tyre

Science.gov (United States)

Niskanen, Arto J.; Tuononen, Ari J.

2017-04-01

Intelligent tyres can provide vital information from the tyre-road contact, especially for autonomous cars and intelligent infrastructure. In this paper, the acceleration measured on the inner liner of a tyre is used to detect the local sliding in the tyre-road contact. The Hilbert-Huang transform is utilized to extract the relevant vibration components and localize them in the wheel rotation angle domain. The energy of the vibration in the trailing part of the contact is shown to increase in low-friction conditions which can be related to the sliding of the tread part as a result of the shear stresses exceeding the local friction limit. To separate the effect of the surface roughness and the friction, different road surfaces were used in the measurements. In addition, the effects of different driving manoeuvres on the measured accelerations and the propagation of the sliding zone in the contact patch during braking are illustrated.

Detection of the local sliding in the tyre-road contact by measuring vibrations on the inner liner of the tyre

International Nuclear Information System (INIS)

Niskanen, Arto J; Tuononen, Ari J

2017-01-01

Intelligent tyres can provide vital information from the tyre-road contact, especially for autonomous cars and intelligent infrastructure. In this paper, the acceleration measured on the inner liner of a tyre is used to detect the local sliding in the tyre-road contact. The Hilbert–Huang transform is utilized to extract the relevant vibration components and localize them in the wheel rotation angle domain. The energy of the vibration in the trailing part of the contact is shown to increase in low-friction conditions which can be related to the sliding of the tread part as a result of the shear stresses exceeding the local friction limit. To separate the effect of the surface roughness and the friction, different road surfaces were used in the measurements. In addition, the effects of different driving manoeuvres on the measured accelerations and the propagation of the sliding zone in the contact patch during braking are illustrated. (paper)

Road Nail: Experimental Solar Powered Intelligent Road Marking System

Science.gov (United States)

Samardžija, Dragan; Teslić, Nikola; Todorović, Branislav M.; Kovač, Erne; Isailović, Đorđe; Miladinović, Bojan

2012-03-01

Driving in low visibility conditions (night time, fog or heavy precipitation) is particularly challenging task with an increased probability of traffic accidents and possible injuries. Road Nail is a solar powered intelligent road marking system of wirelessly networked signaling devices that improve driver safety in low visibility conditions along hazardous roadways. Nails or signaling devices are autonomous nodes with capability to accumulate energy, exchange wireless messages, detect approaching vehicles and emit signalization light. We have built an experimental test-bed that consists of 20 nodes and a cellular gateway. Implementation details of the above system, including extensive measurements and performance evaluations in realistic field deployments are presented. A novel distributed network topology discovery scheme is proposed which integrates both sensor and wireless communication aspects, where nodes act autonomously. Finally, integration of the Road Nail system with the cellular network and the Internet is described.

Safer roads in Chad : recommendations for low-cost road safety measures in Chad. On behalf of The World Bank, International Bank for Reconstruction and Development.

NARCIS (Netherlands)

Sluis, J. van der

2002-01-01

In the framework of the National Transport Support Project, SWOV provided local experts in Chad with technical assistance on road safety. The assistance focused on the development of a comprehensive road safety strategy and physical road safety improvements on urban and inter-urban roads. The

Epidemiologic study of road traffic injuries by road user type characteristics and road environment in Iran: a community-based approach.

Science.gov (United States)

Hatamabadi, Hamidreza; Vafaee, Reza; Hadadi, Mashyaneh; Abdalvand, Ali; Esnaashari, Hamidreza; Soori, Hamid

2012-01-01

Crash injuries in traffic accidents are affected by a variety of factors. In this study we analyzed road user type information based on different contributing factors. Data from all of the road traffic victims on a road extending from the east of the city of Tehran to Mazandaran province were included prospectively over a one-year period (May 2008 to May 2009). Data collected included the crash time, patient's age and sex, road user category, helmet or seat belt use, anatomical site of injury, Injury Severity Score (ISS), and mortality. Prevalence and cross-tabulations were included in the analysis. There were 433 patients, of whom 345 were hospitalized and 33 died either before or after arriving at the hospital. Sixty-nine percent of injured patients were vehicle occupants. Mean and median of ISS were higher for pedestrians, who accounted for 49 percent of the deaths. Head injury was the most common injury and injury to upper and lower extremities was the most common cause of admission. A significant difference in lower extremity injuries between vehicle occupants and nonoccupants was found. Sex and age group did not have a significant effect on mortality. Mortality was significantly higher in pedestrians (P road user type. Because pedestrians are the most vulnerable road users, stricter legislation and law enforcement should be used to protect them. Greater protection can also be reached by holding effective public awareness campaigns on how to use different roads safely. On the other hand, because rear seat passengers are at the same risk for road traffic injuries as front seat passengers, employment of newer laws and preventive measures targeting this group of occupants can prevent many road traffic injuries (RTIs).

Measurements and predictors of on-road ultrafine particle concentrations and associated pollutants in Los Angeles

Energy Technology Data Exchange (ETDEWEB)

Fruin, S. [California Air Resources Board, Sacramento (United States); University of Southern California, Los Angeles (United States). Keck School of Medicine, Department of Preventive Medicine; Westerdahl, D.; Sax, T. [California Air Resources Board, Sacramento (United States); Sioutas, C. [University of Southern California, Los Angeles (United States). Civil and Environmental Engineering; Fine, P.M. [University of Southern California, Los Angeles (United States). Civil and Environmental Engineering; South Coast Air Quality Management District, Diamond Bar, CA (United States)

2008-01-15

Motor vehicles are the dominant source of oxides of nitrogen (NO{sub x}), particulate matter(PM), and certain air toxics (e.g., benzene, 1,3-butadiene) in urban areas. On roadways, motor vehicle-related pollutant concentrations are typically many times higher than ambient concentrations. Due to high air exchange rates typical of moving vehicles, this makes time spent in vehicles on roadways a major source of exposure. This paper presents on-road measurements for Los Angeles freeways and arterial roads taken from a zero-emission electric vehicle outfitted with real-time instruments. The objective was to characterize air pollutant concentrations on roadways and identify the factors associated with the highest concentrations. Our analysis demonstrated that on freeways, concentrations of ultrafine particles (UFPs), black carbon, nitric oxide, and PM-bound polycyclic aromatic hydrocarbons (PM-PAH) are generated primarily by diesel-powered vehicles, despite the relatively low fraction ({approx}6%) of diesel-powered vehicles on Los Angeles freeways. However, UFP concentrations on arterial roads appeared to be driven primarily by proximity to gasoline-powered vehicles undergoing hard accelerations. Concentrations were roughly one-third of those on freeways. By using a multiple regression model for the freeway measurements, we were able to explain 60-70% of the variability in concentrations of UFP, black carbon, nitric oxide, and PM-PAH using measures of diesel truck density and hour of day (as an indicator of wind speed). Freeway concentrations of these pollutants were also well correlated wth readily available annual average daily truck counts, potentially allowing improved population exposure estimates for epidemiology studies. Based on these roadway measurements and average driving time, it appears that 33-45% of total UFP exposure for Los Angeles residents occurs due to time spent traveling in vehicles. (author)

Measurements and predictors of on-road ultrafine particle concentrations and associated pollutants in Los Angeles

International Nuclear Information System (INIS)

Fruin, S.; Sioutas, C.

2008-01-01

Motor vehicles are the dominant source of oxides of nitrogen (NO x ), particulate matter(PM), and certain air toxics (e.g., benzene, 1,3-butadiene) in urban areas. On roadways, motor vehicle-related pollutant concentrations are typically many times higher than ambient concentrations. Due to high air exchange rates typical of moving vehicles, this makes time spent in vehicles on roadways a major source of exposure. This paper presents on-road measurements for Los Angeles freeways and arterial roads taken from a zero-emission electric vehicle outfitted with real-time instruments. The objective was to characterize air pollutant concentrations on roadways and identify the factors associated with the highest concentrations. Our analysis demonstrated that on freeways, concentrations of ultrafine particles (UFPs), black carbon, nitric oxide, and PM-bound polycyclic aromatic hydrocarbons (PM-PAH) are generated primarily by diesel-powered vehicles, despite the relatively low fraction (∼6%) of diesel-powered vehicles on Los Angeles freeways. However, UFP concentrations on arterial roads appeared to be driven primarily by proximity to gasoline-powered vehicles undergoing hard accelerations. Concentrations were roughly one-third of those on freeways. By using a multiple regression model for the freeway measurements, we were able to explain 60-70% of the variability in concentrations of UFP, black carbon, nitric oxide, and PM-PAH using measures of diesel truck density and hour of day (as an indicator of wind speed). Freeway concentrations of these pollutants were also well correlated wth readily available annual average daily truck counts, potentially allowing improved population exposure estimates for epidemiology studies. Based on these roadway measurements and average driving time, it appears that 33-45% of total UFP exposure for Los Angeles residents occurs due to time spent traveling in vehicles. (author)

Measurements and predictors of on-road ultrafine particle concentrations and associated pollutants in Los Angeles

Science.gov (United States)

Fruin, S.; Westerdahl, D.; Sax, T.; Sioutas, C.; Fine, P. M.

Motor vehicles are the dominant source of oxides of nitrogen (NO x), particulate matter (PM), and certain air toxics (e.g., benzene, 1,3-butadiene) in urban areas. On roadways, motor vehicle-related pollutant concentrations are typically many times higher than ambient concentrations. Due to high air exchange rates typical of moving vehicles, this makes time spent in vehicles on roadways a major source of exposure. This paper presents on-road measurements for Los Angeles freeways and arterial roads taken from a zero-emission electric vehicle outfitted with real-time instruments. The objective was to characterize air pollutant concentrations on roadways and identify the factors associated with the highest concentrations. Our analysis demonstrated that on freeways, concentrations of ultrafine particles (UFPs), black carbon, nitric oxide, and PM-bound polycyclic aromatic hydrocarbons (PM-PAH) are generated primarily by diesel-powered vehicles, despite the relatively low fraction (˜6%) of diesel-powered vehicles on Los Angeles freeways. However, UFP concentrations on arterial roads appeared to be driven primarily by proximity to gasoline-powered vehicles undergoing hard accelerations. Concentrations were roughly one-third of those on freeways. By using a multiple regression model for the freeway measurements, we were able to explain 60-70% of the variability in concentrations of UFP, black carbon, nitric oxide, and PM-PAH using measures of diesel truck density and hour of day (as an indicator of wind speed). Freeway concentrations of these pollutants were also well correlated with readily available annual average daily truck counts, potentially allowing improved population exposure estimates for epidemiology studies. Based on these roadway measurements and average driving time, it appears that 33-45% of total UFP exposure for Los Angeles residents occurs due to time spent traveling in vehicles.

Tyre contact length on dry and wet road surfaces measured by three-axial accelerometer

Science.gov (United States)

Matilainen, Mika; Tuononen, Ari

2015-02-01

We determined the tyre contact length on dry and wet roads by measuring the accelerations of the inner liner with a three-axial accelerometer. The influence of the tyre pressure, driving velocity, and tread depth on the contact length was studied in both types of road surface conditions. On dry asphalt the contact length was almost constant, regardless of the driving velocity. On wet asphalt the presence of water could be detected even at low driving velocities (e.g. 20 km/h for a worn tyre) as the contact length began to decrease from that found in the dry asphalt situation. In addition to improving the performance of active safety systems and driver warning systems, the contact length information could be beneficial for classifying and studying the aquaplaning behaviour of tyres.

Characterizing a porous road pavement using surface impedance measurement: a guided numerical inversion procedure.

Science.gov (United States)

Benoit, Gaëlle; Heinkélé, Christophe; Gourdon, Emmanuel

2013-12-01

This paper deals with a numerical procedure to identify the acoustical parameters of road pavement from surface impedance measurements. This procedure comprises three steps. First, a suitable equivalent fluid model for the acoustical properties porous media is chosen, the variation ranges for the model parameters are set, and a sensitivity analysis for this model is performed. Second, this model is used in the parameter inversion process, which is performed with simulated annealing in a selected frequency range. Third, the sensitivity analysis and inversion process are repeated to estimate each parameter in turn. This approach is tested on data obtained for porous bituminous concrete and using the Zwikker and Kosten equivalent fluid model. This work provides a good foundation for the development of non-destructive in situ methods for the acoustical characterization of road pavements.

Trajectory of a road vehicle during road maintenance

OpenAIRE

Stachová Darina

2017-01-01

Consider a vehicle moving on a road whose usage over time creates an uneven surface on the road. Road unevenness that we encounter on surface communications often arises as a consequence of dynamical effects of moving vehicles, of weather changes, and due to road construction works. This article concerns with mathematical modeling of the trajectory of a road vehicle moving on such a surface during the course of road maintenance.

A Fuel-Based Assessment of On-Road and Off-Road Mobile Source Emission Trends

Science.gov (United States)

Dallmann, T. R.; Harley, R. A.

2009-12-01

Mobile sources contribute significantly to emissions of nitrogen oxides (NOx) and fine particulate matter (PM2.5) in the United States. These emissions lead to a variety of environmental concerns including adverse human health effects and climate change. In the electric power sector, sulfur dioxide (SO2) and NOx emissions from power plants are measured directly using continuous emission monitoring systems. In contrast for mobile sources, statistical models are used to estimate average emissions from a very large and diverse population of engines. Despite much effort aimed at improving them, mobile source emission inventories continue to have large associated uncertainties. Alternate methods are needed to help evaluate estimates of mobile source emissions and quantify and reduce the associated uncertainties. In this study, a fuel-based approach is used to estimate emissions from mobile sources, including on-road and off-road gasoline and diesel engines. In this approach, engine activity is measured by fuel consumed (in contrast EPA mobile source emission models are based on vehicle km of travel and total amount of engine work output for on-road and off-road engines, respectively). Fuel consumption is defined in this study based on highway fuel tax reports for on-road engines, and from surveys of fuel wholesalers who sell tax-exempt diesel fuel for use in various off-road sectors such as agriculture, construction, and mining. Over the decade-long time period (1996-2006) that is the focus of the present study, national sales of taxable gasoline and diesel fuel intended for on-road use increased by 15 and 43%, respectively. Diesel fuel use by off-road equipment increased by about 20% over the same time period. Growth in fuel consumption offset some of the reductions in pollutant emission factors that occurred during this period. This study relies on in-use measurements of mobile source emission factors, for example from roadside and tunnel studies, remote sensing, and

Virtual testing of speed reduction schemes on urban collector roads.

Science.gov (United States)

Domenichini, Lorenzo; Branzi, Valentina; Meocci, Monica

2018-01-01

Urban collector roads are complex driving environments often encompassing both the mobility and the access road functions. In these conditions motorized traffic and vulnerable road users compete continually. Speed reduction measures may play a relevant role in these contexts, provided that such measures are also designed in compliance with the driver's capabilities and expectations. The paper describes a test procedure using driving simulation experiments, designed to evaluate the reconfiguration project of Via Pistoiese, an urban road collector located in Florence (Italy). The road improvement design consisted of several engineering treatments aimed to reduce and homogenize the driving speed, as well as to manage the co-existence of the different road users and mainly to protect pedestrians. The main focus of the research was to understand if the drivers' behaviour was according to the design hypothesis before the safety treatments are implemented in the real world. Due to the multiple engineering treatments included in the reconfiguration project, the evaluation of the overall safety effectiveness of the project rather than the single treatment safety impact was the main concern of the research study. In addition, the study aimed to assess the usefulness of the considered testing method to understand how to integrate road design with drivers' performances, especially in heterogeneous traffic environments where drivers' behaviour plays a decisive role in the success of the proposed design solutions. Fifty-eight participants drove through two immersive virtual environments, reproducing the existing configuration and the project reconfiguration, while data relating to different driving aspects were collected. Two analyses were performed. The first was focused on the analysis of the mean speed profiles and revealed that the considered engineering treatments are able to control the speeding behaviour without providing a too high discomfort to the drivers. The second

Optimized Estimation of Surface Layer Characteristics from Profiling Measurements

Directory of Open Access Journals (Sweden)

Doreene Kang

2016-01-01

Full Text Available New sampling techniques such as tethered-balloon-based measurements or small unmanned aerial vehicles are capable of providing multiple profiles of the Marine Atmospheric Surface Layer (MASL in a short time period. It is desirable to obtain surface fluxes from these measurements, especially when direct flux measurements are difficult to obtain. The profiling data is different from the traditional mean profiles obtained at two or more fixed levels in the surface layer from which surface fluxes of momentum, sensible heat, and latent heat are derived based on Monin-Obukhov Similarity Theory (MOST. This research develops an improved method to derive surface fluxes and the corresponding MASL mean profiles of wind, temperature, and humidity with a least-squares optimization method using the profiling measurements. This approach allows the use of all available independent data. We use a weighted cost function based on the framework of MOST with the cost being optimized using a quasi-Newton method. This approach was applied to seven sets of data collected from the Monterey Bay. The derived fluxes and mean profiles show reasonable results. An empirical bias analysis is conducted using 1000 synthetic datasets to evaluate the robustness of the method.

Road safety and road traffic accidents in Saudi Arabia

Science.gov (United States)

Mansuri, Farah A.; Al-Zalabani, Abdulmohsen H.; Zalat, Marwa M.; Qabshawi, Reem I.

2015-01-01

Objectives: To identify the changing trends and crucial preventive approaches to road traffic accidents (RTAs) adopted in the Kingdom of Saudi Arabia (KSA) over the last 2.5 decades, and to analyze aspects previously overlooked. Methods: This systematic review was based on evidence of RTAs in KSA. All articles published during the last 25 years on road traffic accident in KSA were analyzed. This study was carried out from December 2013 to May 2014 in the Department of Family and Community Medicine, Taibah University, Al-Madinah Al-Munawwarah, KSA. Results: Road traffic accidents accounted for 83.4% of all trauma admissions in 1984-1989, and no such overall trend was studied thereafter. The most frequently injured body regions as reported in the latest studies were head and neck, followed by upper and lower extremities, which was found to be opposite to that of the studies reported earlier. Hospital data showed an 8% non-significant increase in road accident mortalities in contrast to police records of a 27% significant reduction during the years 2005-2010. Excessive speeding was the most common cause reported in all recent and past studies. Conclusion: Disparity was common in the type of reporting of RTAs, outcome measures, and possible causes over a period of 2.5 decade. All research exclusively looked into the drivers’ faults. A sentinel surveillance of road crashes should be kept in place in the secondary and tertiary care hospitals for all regions of KSA. PMID:25828277

Relationships between road safety, safety measures and external factors : a scan of the literature in view of model development and topics for further research.

NARCIS (Netherlands)

Churchill, T. & Norden, Y. van

2010-01-01

The purpose of this literature scan is to examine where literature on the effect of external factors and road safety measures on road safety exists and where it is lacking. This scan will help us to decide which factors to include in a comprehensive road safety model as SWOV is working on, and at

Braking distance algorithm for autonomous cars using road surface recognition

Science.gov (United States)

Kavitha, C.; Ashok, B.; Nanthagopal, K.; Desai, Rohan; Rastogi, Nisha; Shetty, Siddhanth

2017-11-01

India is yet to accept semi/fully - autonomous cars and one of the reasons, was loss of control on bad roads. For a better handling on these roads we require advanced braking and that can be done by adapting electronics into the conventional type of braking. In Recent years, the automation in braking system led us to various benefits like traction control system, anti-lock braking system etc. This research work describes and experiments the method for recognizing road surface profile and calculating braking distance. An ultra-sonic surface recognition sensor, mounted underneath the car will send a high frequency wave on to the road surface, which is received by a receiver with in the sensor, it calculates the time taken for the wave to rebound and thus calculates the distance from the point where sensor is mounted. A displacement graph will be plotted based on the output of the sensor. A relationship can be derived between the displacement plot and roughness index through which the friction coefficient can be derived in Matlab for continuous calculation throughout the distance travelled. Since it is a non-contact type of profiling, it is non-destructive. The friction coefficient values received in real-time is used to calculate optimum braking distance. This system, when installed on normal cars can also be used to create a database of road surfaces, especially in cities, which can be shared with other cars. This will help in navigation as well as making the cars more efficient.

A national-scale review of air pollutant concentrations measured in the U.S. near-road monitoring network during 2014 and 2015

Science.gov (United States)

DeWinter, Jennifer L.; Brown, Steven G.; Seagram, Annie F.; Landsberg, Karin; Eisinger, Douglas S.

2018-06-01

In 2010, the U.S. Environmental Protection Agency (EPA) revised the National Ambient Air Quality Standards (NAAQS) for NO2 to include a primary health-based standard for hourly NO2, and required air quality monitoring next to major roadways in urban areas in the U.S. Requirements for near-road measurements also include carbon monoxide (CO) and particulate matter smaller than 2.5 μm in diameter (PM2.5). We performed a national-scale assessment of air pollutants measured at 81 sites in the near-road environment during the first two years (2014 and 2015) of the new measurement program. We evaluated how concentrations at these locations compared to the NAAQS, to concentrations measured at other sites within the same urban areas, and when considering their site characteristics (distance of monitor to road, traffic volume, and meteorology). We also estimated the contribution of emissions from adjacent roadways at each near-road site to the PM2.5 concentrations above the local urban background concentrations, i.e., the near-road "increment." Hourly values of CO reached a maximum of 4.8 ppm across 31 sites in 2014 and 9.6 ppm across 47 sites in 2015, and were well below the NAAQS levels for both the 1-hr (35 ppm) and 8-hr (9 ppm) standards. Hourly concentrations of near-road NO2 reached 258 ppb across 40 sites in 2014; however, there were only two occurrences of a daily 1-hr maximum NO2 concentration above 100 ppb (the level of the hourly NO2 standard). In 2015, hourly concentrations of near-road NO2, monitored at 61 sites in 55 urban areas, reached 154 ppb. Only 0.0015% (n = 5) of hourly NO2 observations in 2015 exceeded 100 ppb. The highest annual NO2 average recorded in 2015 (29.9 ppb) occurred at the Ontario site located along I-10 in the Los Angeles, California, area and was below the level of the NO2 annual standard (53 ppb); in 2014, the highest annual mean NO2 was also observed in Los Angeles at the Anaheim site (27.1 ppb). In 2014, sites in Cincinnati

Driving and off-road impairments underlying failure on road testing in Parkinson's disease.

Science.gov (United States)

Devos, Hannes; Vandenberghe, Wim; Tant, Mark; Akinwuntan, Abiodun E; De Weerdt, Willy; Nieuwboer, Alice; Uc, Ergun Y

2013-12-01

Parkinson's disease (PD) affects driving ability. We aimed to determine the most critical impairments in specific road skills and in clinical characteristics leading to failure on a road test in PD. In this cross-sectional study, certified driving assessment experts evaluated specific driving skills in 104 active, licensed drivers with PD using a standardized, on-road checklist and issued a global decision of pass/fail. Participants also completed an off-road evaluation assessing demographic features, disease characteristics, motor function, vision, and cognition. The most important driving skills and off-road predictors of the pass/fail outcome were identified using multivariate stepwise regression analyses. Eighty-six (65%) passed and 36 (35%) failed the on-road driving evaluation. Persons who failed performed worse on all on-road items. When adjusted for age and gender, poor performances on lateral positioning at low speed, speed adaptations at high speed, and left turning maneuvers yielded the best model that determined the pass/fail decision (R(2) = 0.56). The fail group performed poorer on all motor, visual, and cognitive tests. Measures of visual scanning, motor severity, PD subtype, visual acuity, executive functions, and divided attention were independent predictors of pass/fail decisions in the multivariate model (R(2) = 0.60). Our study demonstrated that failure on a road test in PD is determined by impairments in specific driving skills and associated with deficits in motor, visual, executive, and visuospatial functions. These findings point to specific driving and off-road impairments that can be targeted in multimodal rehabilitation programs for drivers with PD. © 2013 Movement Disorder Society.

Solutions to Improve Road Circulation in the Pitesti City Based on Analysis-Diagnostics of Road Traffic

Science.gov (United States)

Vîlcan, A.; Neagu, E.; Badarau Suster, H.; Boroiu, A. A.

2017-10-01

Road traffic congestion has become a daily phenomenon in the central area of Pitesti in the peak traffic periods. In order to achieve the mobility plan of Pitesti, an important stage is the diagnostic analysis of the road traffic. For this purpose, the urban road network was formalized through a graph containing the most important 40 intersections and traffic measurements were made at all these intersections and on the main roads connecting the peri-urban area. The data obtained by traffic macrosimulation confirmed the overloading of the street network during peak traffic hours and the analyzes made for various road traffic organization scenarios have shown that there are sustainable solutions for urban mobility only if the road network is fundamentally reconfigured (a belt outside the city and a median ring). Thus, the necessity of realizing the road passage in the Prundu neighbourhood and the finishing of the city belt by realizing the “detour West” of the city is argued. The importance of the work is that it brings scientific arguments for the realization of these road infrastructure projects, integrated in the urban mobility plan, which will base the development strategy of the Pitesti municipality.

Calculating Traffic based on Road Sensor Data

NARCIS (Netherlands)

Bisseling, Rob; Gao, Fengnan; Hafkenscheid, Patrick; Idema, Reijer; Jetka, Tomasz; Guerra Ones, Valia; Rata, Debanshu; Sikora, Monika

2014-01-01

Road sensors gather a lot of statistical data about traffic. In this paper, we discuss how a measure for the amount of traffic on the roads can be derived from this data, such that the measure is independent of the number and placement of sensors, and the calculations can be performed quickly for

Explaining seemingly paradoxical consumer experiences: conjoining weekly road rage and church attendance.

Science.gov (United States)

Gau, Li-Shiue; Woodside, Arch G; Martin, Drew

2015-02-01

The purposes of the current study are threefold: Provide evidence that an extreme paradoxical group exists-people frequently attending church and exhibiting road rage, profile this group, and frame possible explanations for the seemingly paradoxical behaviors. This study employs data from a national (USA) lifestyle survey conducted by Market Facts with 3,350 American respondents. The major questions asked about church participation and road-rage behavior ("giving a finger" and "flashing headlights"). Nomologically, relevant activities include 3 items for church goers and 3 items for road-rage givers. Additionally, 14 items profiled the lifestyles of the unique paradoxical behavior segment. Utilizing cross-tabulation tables, property space analyses identify the double extreme (XX) group (18 people) and other 6 groups with a significant chi-square test, confirming the extreme group exists. Analyses of variance test results show that comparing nomologically relevant activities among the seven groups is all statistically significant, indicating the nomological validity is met. Overall, the XX group tends to have more males, be younger, and have a higher proportion of people working in sales. The profile of lifestyle analyses shows the XX group members have both high ambitions and expectations, might be very frustrated individuals, and equip with the adventurous and masculine traits related to aggression. The XX behavior group's demographic and psychographic characteristics portray similar lifestyles that differ from other groups. Case-based analyses provide further contextual information of nuances to XX segment individuals. The limited energy theory, the Eagleman's theory of unconscious mind, and justification theory help to explain why people conjointly go to church and commit road rage. Addressing chronic paradoxical behaviors provides implications for social de-marketing to reduce aggressive anti-social behavior such as road rage. Frequent church attendance may

Over-pressure in road tankers; Ueberdrucksicherung an Tankfahrzeugen

Energy Technology Data Exchange (ETDEWEB)

Frobese, Dirk-Hans; Pape, Harald [Physikalisch-Technische Bundesanstalt, Braunschweig (Germany)

2011-08-15

This work was aimed at determining possible causes of overpressure damages on road tankers. In cooperation with the manufacturers of road tankers, the equipment of road tankers usually used today was, therefore, discussed and possible error sources determined. In measurements performed at two filling stations, real pressure, temperature and volume flow ratios for the loading of a road tanker were recorded. Parallel to it, tests in a cold chamber were carried out to determine the possibility and the general conditions of an icing of the tilting valve and the flame arrester. With these results, scenarios have been worked out which can explain known overpressure damaging events. On the basis of a risk assessment, measures are described how such overpressure damages on road tankers can in future be avoided. (orig.)

The quantifying of road safety developments. Paper presented at the International Conference 'Road Safety in Europe', Birmingham, September 9-11, 1996.

NARCIS (Netherlands)

Koornstra, M.J.

1996-01-01

The evaluation of the effectiveness of road safety policies and measures must be based on quantative information in road safety developments and the relevant variables that influence that development. However, the concept of road safety itself is not well defined theoretically and quantatively. This

The effects of `non-infrastructural' measures to improve the safety of vulnerable road users : a review of international findings, prepared for the OECD Scientific Expert Group "Safety of vulnerable road users".

OpenAIRE

Hagenzieker, M.P.

1997-01-01

This report reviews the evaluated effects of what can be called `non-infrastructural measures' to improve the safety of vulnerable road users. Three selected areas are discussed: education and training, measures to enhance visibility and conspecuity, and protective devices for bicyclists. Other types of non-infrastructural measures are briefly mentioned.

Inhalation of road dust by human subjects.

Science.gov (United States)

Takishima, T; Nakamura, M; Sasaki, M; Miyano, M; Yamaya, M; Sasaki, H

1987-11-01

We measured pneumomagnetic field strength (PMFS) in 42 healthy control subjects living in districts of Northern Japan with low levels of road dust pollution and in 39 healthy subjects living in areas with high levels of road dust pollution. Suspended road dust produced by studded tires increases from 30 micrograms/m3 during the summer season to levels as high as 400 micrograms/m3 during the snow season in the downtown areas of Sendai, Japan. Road dust retained in the lungs, containing 3% iron, was magnetized from the surface of the chest wall, and PMFS was measured. Three to 5 sequential PMFS measurements were made in each subject in March and October of 1984 and 1985, and in March 1986. The PMFS in control subjects in March 1984 was 37 +/- 14 pico-Tesla (mean +/- SD) and did not significantly differ from the PMFS in October 1984 or that in March 1985. In March 1984, the PMFS of the subjects in highly polluted areas was 95 +/- 100 pico-Tesla (mean +/- SD) and was significantly higher than that of control subjects (p less than 0.01) and subsequently decreased in March 1985 and in March 1986, corresponding to a decrease in suspended road dust brought about by a campaign to eliminate the use of studded tires. Our findings suggest that some road dust caused by studded tires is retained in the lungs.

The effects of `non-infrastructural' measures to improve the safety of vulnerable road users : a review of international findings, prepared for the OECD Scientific Expert Group "Safety of vulnerable road users".

NARCIS (Netherlands)

Hagenzieker, M.P.

1997-01-01

This report reviews the evaluated effects of what can be called `non-infrastructural measures' to improve the safety of vulnerable road users. Three selected areas are discussed: education and training, measures to enhance visibility and conspecuity, and protective devices for bicyclists. Other

Automatic Road Centerline Extraction from Imagery Using Road GPS Data

Directory of Open Access Journals (Sweden)

Chuqing Cao

2014-09-01

Full Text Available Road centerline extraction from imagery constitutes a key element in numerous geospatial applications, which has been addressed through a variety of approaches. However, most of the existing methods are not capable of dealing with challenges such as different road shapes, complex scenes, and variable resolutions. This paper presents a novel method for road centerline extraction from imagery in a fully automatic approach that addresses the aforementioned challenges by exploiting road GPS data. The proposed method combines road color feature with road GPS data to detect road centerline seed points. After global alignment of road GPS data, a novel road centerline extraction algorithm is developed to extract each individual road centerline in local regions. Through road connection, road centerline network is generated as the final output. Extensive experiments demonstrate that our proposed method can rapidly and accurately extract road centerline from remotely sensed imagery.

Space potential, temperature, and density profile measurements on RENTOR

International Nuclear Information System (INIS)

Schoch, P.M.

1983-05-01

Radial profiles of the space potential, electron temperature, and density have been measured on RENTOR with a heavy-ion-beam probe. The potential profile has been compared to predictions from a stochastic magnetic field fluctuation theory, using the measured temperature and density profiles. The comparison shows strong qualitative agreement in that the potential is positive and the order of T/sub e//e. There is some quantitative disagreement in that the measured radial electric fields are somewhat smaller than the theoretical predictions. To facilitate this comparison, a detailed analysis of the possible errors has been completed

European car drivers' opinions about road safety measures and in-car devices.

NARCIS (Netherlands)

Goldenbeld, C.

1999-01-01

In 1991, a representative survey of drivers was conducted in 15 European countries. This project was named `SARTRE' which stands for 'Social Attitudes to Road Traffic Risk in Europe'. The survey focused on drivers' road behaviour, attitudes and opinions concerning drinking and driving, speeding and

Sensitivity analysis of the near-road dispersion model RLINE - An evaluation at Detroit, Michigan

Science.gov (United States)

Milando, Chad W.; Batterman, Stuart A.

2018-05-01

The development of accurate and appropriate exposure metrics for health effect studies of traffic-related air pollutants (TRAPs) remains challenging and important given that traffic has become the dominant urban exposure source and that exposure estimates can affect estimates of associated health risk. Exposure estimates obtained using dispersion models can overcome many of the limitations of monitoring data, and such estimates have been used in several recent health studies. This study examines the sensitivity of exposure estimates produced by dispersion models to meteorological, emission and traffic allocation inputs, focusing on applications to health studies examining near-road exposures to TRAP. Daily average concentrations of CO and NOx predicted using the Research Line source model (RLINE) and a spatially and temporally resolved mobile source emissions inventory are compared to ambient measurements at near-road monitoring sites in Detroit, MI, and are used to assess the potential for exposure measurement error in cohort and population-based studies. Sensitivity of exposure estimates is assessed by comparing nominal and alternative model inputs using statistical performance evaluation metrics and three sets of receptors. The analysis shows considerable sensitivity to meteorological inputs; generally the best performance was obtained using data specific to each monitoring site. An updated emission factor database provided some improvement, particularly at near-road sites, while the use of site-specific diurnal traffic allocations did not improve performance compared to simpler default profiles. Overall, this study highlights the need for appropriate inputs, especially meteorological inputs, to dispersion models aimed at estimating near-road concentrations of TRAPs. It also highlights the potential for systematic biases that might affect analyses that use concentration predictions as exposure measures in health studies.

Real-world emissions and fuel consumption of diesel buses and trucks in Macao: From on-road measurement to policy implications

Science.gov (United States)

Wu, Xiaomeng; Zhang, Shaojun; Wu, Ye; Li, Zhenhua; Zhou, Yu; Fu, Lixin; Hao, Jiming

2015-11-01

A total of 13 diesel buses and 12 diesel trucks in Macao were tested using portable emission measurement systems (PEMS) including a SEMTECH-DS for gaseous emissions and a SEMTECH-PPMD for PM2.5. The average emission rates of gaseous pollutants and CO2 are developed with the operating mode defined by the instantaneous vehicle specific power (VSP) and vehicle speed. Both distance-based and fuel mass-based emission factors for gaseous pollutants (e.g., CO, THC and NOX) are further estimated under typical driving conditions. The average distance-based NOX emission of heavy-duty buses (HDBs) is higher than 13 g km-1. Considering the unfavorable conditions for selective reductions catalyst (SCR) systems, such as low-speed driving conditions, more effective technology options (e.g., dedicated natural gas buses and electric buses) should be considered by policy makers in Macao. We identified strong effects of the vehicle size, engine displacement and driving conditions on real-world CO2 emission factors and fuel consumption for diesel vehicles. Therefore, detailed profiles regarding vehicle specifications can reduce the uncertainty in their fleet-average on-road fuel consumption. In addition, strong correlations between relative emission factors and driving conditions indicated by the average speed of generated micro-trips are identified based on a micro-trip method. For example, distance-based emission factors of HDBs will increase by 39% for CO, 29% for THC, 43% for NOX and 26% for CO2 when the average speed decreases from 30 km h-1 to 20 km h-1. The mitigation of on-road emissions from diesel buses and trucks by improving traffic conditions through effective traffic and economic management measures is therefore required. This study demonstrates the important role of PEMS in understanding vehicle emissions and mitigation strategies from science to policy perspectives.

On-road measurement of NH3 emissions from gasoline and diesel passenger cars during real world driving conditions

Science.gov (United States)

Suarez-Bertoa, Ricardo; Mendoza-Villafuerte, Pablo; Riccobono, Francesco; Vojtisek, Michal; Pechout, Martin; Perujo, Adolfo; Astorga, Covadonga

2017-10-01

NH3 is a precursor of PM2.5 which deteriorates urban air quality, affects human health and impacts the global radiation budget. Since vehicles are important sources of NH3 in urban areas, we have satisfactorily studied the possibility of measuring NH3 emissions from gasoline and SCR-equipped diesel light-duty vehicles during real driving on-road operation using a portable FTIR. The performance of the portable FTIR resulted to be comparable to that of a laboratory-based FTIR during a series of experiments performed in the Vehicle Emission Laboratory (VELA) using the World-harmonized Light-duty Test Cycle (WLTC). Higher on-road NH3 emission factors were obtained for the gasoline vehicle than for the diesel. High NOx emissions were measured from the diesel vehicle, indicating a low efficiency of the DeNOx system, SCR. On-road NH3 emission factors were ∼2 times lower than during the laboratory tests at 23 °C for both vehiclesNH3 emissions were not observed for the diesel vehicle during cold start operation. However, NH3 cold start emissions from the gasoline vehicle were up to 2 orders of magnitude higher than during the entire road trips, ranging from 45 to 134 mg km-1. Cold start emissions are of paramount importance as they commonly take place in urban areas. Hence, future urban reductions in PM2.5 might need to take into consideration the introduction of NH3 emissions limits for passenger cars.

Assessment of on-road transportation demand and CO2 emissions for determination of air quality impacts from the Megacity of São Paulo

Science.gov (United States)

Perez-Martinez, P. J.; Miranda, R. M.; Andrade, M. D. F.

2017-12-01

In this manuscript we assess the capability of using mobility surveys and a high-scale assignment and emission model to study climate change and air quality impacts related to on-road transportation in the Megacity of São Paulo (MSP). Initially, we estimate CO2 emissions of light and heavy vehicles (LVs and HVs) at a spatial scale of 500m and temporal scale of an hour, using transport demand modeling. The estimates are based on origin and destination trip pairs and the height of the planetary boundary layer (PBL). These estimates, performed for the years 2007 and 2012, depend also on intermediate variables as dilution rates (D) and surface particulate-matter concentrations (PM). Secondly, we assess the changes in CO2 vehicle emissions from the MRSP over the period 2007-2012 (4% year-1). Consequently, CO2 emission inventories merge trip-based surveys, traffic assignments and road network database with air pollution monitoring data. Despite the difference of the methodologies, we use a road link bottom up vehicle activity based approach, the assessed emissions agree with the State's Emission Inventory. This paper shows that the CO2 emissions from LDVs and HDVs in the MSP in 2007 and 2012 were 8,477 and 10,075 tCeq day-1 (58% LVs and 42% HVs), respectively. CO2 emissions from vehicles show spatial patterns consistent with passenger and freight transport trips and road network assignments. Temporal profiles (diurnal, weekly and monthly) were estimated using traffic counts and congestion surrogates. The profiles were compared with average road-site (Western of MSP) and background (Jaraguá Peak) CO2 measurements available for 2014. On-road measurements showed one peak associated to the morning peak hour of vehicles (437±45 ppm) and another night peak (435±49 ppm) related to the low PBL (313 m) and D (329 m2 h-1). From on-road measurements, background values (414±2 ppm) were subtracted to estimate excess CO2 (12±8 ppm) directly attributed to vehicles. The inventory

Experimental investigations of tyre-road interactions during braking; Experimentelle Untersuchungen zur Interaktion zwischen Pkw-Reifen und Fahrbahn beim Bremsen

Energy Technology Data Exchange (ETDEWEB)

Chunyang Xie

2002-07-01

Tyre-road interactions during braking were investigated experimentally. The measurements were found to be highly accurate. In the first stage, the braking force is enhanced by elastic deformation of the profile elements at the onset of tyre contact. In case of high slip or a high sliding velocity, frictional vibration of the tyre section in contact with the road may occur, which is enhanced by the reduction of braking pressure in case of automatic brake control. The eigenfreequency of the frictional vibration also depends on the road texture and friction coefficient. The measured movements of the profile elements provide a good explanation of the causes of tyre noise. [German] In der Dissertation wurde die Interaktion Reifen/Fahrbahn beim Bremsen experimentell untersucht. Die Messungen zeigen, dass die mit dem neuen Reifensensor erfassten Profilelementverformungen den Reibungszustand zwischen Reifen und Fahrbahn gut widerspiegeln. Die Bremskraft wird zunaechst durch die elastischen Verformungen der Profilelemente am Anfang des Reifenlatsches wesentlich aufgebaut. Beim hohen Bremsschlupf bzw. der hohen Gleitgeschwindigkeit kann die Reibungsschwingung des Laufstreifens des Reifens auftreten. Der Bremsdruckabbau der ABS-Regelung beguenstigt die Entstehung dieser Reibungsschwingung. Die Eigenfrequenz der Reibungsschwingung ist auch abhaengig von der Fahrbahntextur und dem Reibwert. Die aus den Signalen des Profilrillensensors berechneten Beschleunigungen der Profilelemente zeigen deutlich den Aufschlag beim Einlauf des Reifens und das Ausschnappen beim Auslauf. Durch die gemessenen Bewegungen der Profilelemente laesst sich die Entstehung des Reifengeraeusches in einigen Frequenzbereichen gut erklaeren. (orig.)

Verification of road databases using multiple road models

Science.gov (United States)

Ziems, Marcel; Rottensteiner, Franz; Heipke, Christian

2017-08-01

In this paper a new approach for automatic road database verification based on remote sensing images is presented. In contrast to existing methods, the applicability of the new approach is not restricted to specific road types, context areas or geographic regions. This is achieved by combining several state-of-the-art road detection and road verification approaches that work well under different circumstances. Each one serves as an independent module representing a unique road model and a specific processing strategy. All modules provide independent solutions for the verification problem of each road object stored in the database in form of two probability distributions, the first one for the state of a database object (correct or incorrect), and a second one for the state of the underlying road model (applicable or not applicable). In accordance with the Dempster-Shafer Theory, both distributions are mapped to a new state space comprising the classes correct, incorrect and unknown. Statistical reasoning is applied to obtain the optimal state of a road object. A comparison with state-of-the-art road detection approaches using benchmark datasets shows that in general the proposed approach provides results with larger completeness. Additional experiments reveal that based on the proposed method a highly reliable semi-automatic approach for road data base verification can be designed.

Flow monitoring along the western Tamiami Trail between County Road 92 and State Road 29 in support of the Comprehensive Everglades Restoration Plan, 2007-2010

Science.gov (United States)

Booth, Amanda C.; Soderqvist, Lars E.; Berry, Marcia C.

2014-01-01

The construction of U.S. Highway 41 (Tamiami Trail), the Southern Golden Gate Estates development, and the Barron River Canal has altered the flow of freshwater to the Ten Thousand Islands estuary of Southwest Florida. Two restoration projects, the Picayune Strand Restoration Project and the Tamiami Trail Culverts Project, both associated with the Comprehensive Everglades Restoration Plan, were initiated to address this issue. Quantifying the flow of freshwater to the estuary is essential to assessing the effectiveness of these projects. The U.S. Geological Survey conducted a study between March 2006 and September 2010 to quantify the freshwater flowing under theTamiami Trail between County Road 92 and State Road 29 in southwest Florida, excluding the Faka Union Canal (which is monitored by South Florida Water Management District). The study period was after the completion of the Tamiami Trail Culverts Project and prior to most of the construction related to the Picayune Restoration Project. The section of the Tamiami Trail that was studied contains too many structures (35 bridges and 16 culverts) to cost-effectively measure each structure on a continuous basis, so the area was divided into seven subbasins. One bridge within each of the subbasins was instrumented with an acoustic Doppler velocity meter. The index velocity method was used to compute discharge at the seven instrumented bridges. Periodic discharge measurements were made at all structures, using acoustic Doppler current profilers at bridges and acoustic Doppler velocity meters at culverts. Continuous daily mean values of discharge for the uninstrumented structures were calculated on the basis of relations between the measured discharge at the uninstrumented stations and the discharge and stage at the instrumented bridge. Estimates of daily mean discharge are available beginning in 2006 or 2007 through September 2010 for all structures. Subbasin comparison is limited to water years 2008–2010. The Faka

A method for measuring the inductive electric field profile and noninductive current profiles on DIII-D

International Nuclear Information System (INIS)

Forest, C.B.; Luce, T.C.; Politzer, P.A.; Lao, L.L.; Kupfer, K.; Wroblewski, D.

1994-07-01

A new technique for determining the parallel electric field profile and noninductive current profile in tokamak plasmas has been developed and applied to two DIII-D tokamak discharges. Central to this technique is the determination of the current density profile, J(ρ), and poloidal flux, ψ(ρ), from equilibrium reconstructions. From time sequences of the reconstructions, the flux surface averaged, parallel electric field can be estimated from appropriate derivatives of the poloidal flux. With a model for the conductivity and measurements of T e and Z eff , the noninductive fraction of the current can be determined. Such a technique gives the possibility of measuring directly the bootstrap current profile and the noninductively driven current from auxiliary heating such as neutral beam injection or fast wave current drive. Furthermore, if the noninductively driven current is small or if the noninductive current profile is assumed to be known, this measurement provides a local test of the conductivity model under various conditions

Study on Emission Measurement of Vehicle on Road Based on Binomial Logit Model

OpenAIRE

Aly, Sumarni Hamid; Selintung, Mary; Ramli, Muhammad Isran; Sumi, Tomonori

2011-01-01

This research attempts to evaluate emission measurement of on road vehicle. In this regard, the research develops failure probability model of vehicle emission test for passenger car which utilize binomial logit model. The model focuses on failure of CO and HC emission test for gasoline cars category and Opacity emission test for diesel-fuel cars category as dependent variables, while vehicle age, engine size, brand and type of the cars as independent variables. In order to imp...

The Relationship between Road Design and Driving Behavior

DEFF Research Database (Denmark)

Abele, Liva; Møller, Mette

2011-01-01

Speed is a substantial factor contributing to road safety. Currently, speed reduction is mainly achieved through law enforcement and the implementation of traffic calming measures. An alternative speed reducing approach is to encourage drivers to voluntarily choose an appropriate driving speed....... Improving road infrastructure safety can be achieved by making roads forgiving and self-explaining. This could be done by clarifying the road design characteristics for each road category. The effect on driver behavior by varying road-shoulders and presence of roadside trees was tested by means of a fixed-driving...... simulator experiment. Speed and lateral position were used as performance indicators. The results indicated that shoulders might not be applied to decrease the speed on the experimental road stretch, but their presence cause drivers to drive closer to the road edge, hence eliminating the probability of head...

Vehicle-specific emissions modeling based upon on-road measurements.

Science.gov (United States)

Frey, H Christopher; Zhang, Kaishan; Rouphail, Nagui M

2010-05-01

Vehicle-specific microscale fuel use and emissions rate models are developed based upon real-world hot-stabilized tailpipe measurements made using a portable emissions measurement system. Consecutive averaging periods of one to three multiples of the response time are used to compare two semiempirical physically based modeling schemes. One scheme is based on internally observable variables (IOVs), such as engine speed and manifold absolute pressure, while the other is based on externally observable variables (EOVs), such as speed, acceleration, and road grade. For NO, HC, and CO emission rates, the average R(2) ranged from 0.41 to 0.66 for the former and from 0.17 to 0.30 for the latter. The EOV models have R(2) for CO(2) of 0.43 to 0.79 versus 0.99 for the IOV models. The models are sensitive to episodic events in driving cycles such as high acceleration. Intervehicle and fleet average modeling approaches are compared; the former account for microscale variations that might be useful for some types of assessments. EOV-based models have practical value for traffic management or simulation applications since IOVs usually are not available or not used for emission estimation.

Mobile system for on-road measurements of air pollutants

Science.gov (United States)

Katulski, Ryszard J.; Namieśnik, Jacek; Sadowski, Jarosław; Stefański, Jacek; Szymańska, Krystyna; Wardencki, Waldemar

2010-04-01

The paper presents a prototype of a mobile monitoring system for measuring the levels of the main traffic air pollutants (C6H6, NO2, NOx, CO, and CO2,) in cities. The novelty of the proposed system lies in the fact that it can be utilized to monitor emissions from urban traffic along roads and areas where traditional monitoring stations cannot be placed. In the proposed system, the monitoring device can be mounted on any moving vehicle (such as a car, bus, or truck) rather than be attached to a dedicated van, as most systems of this kind found in literature are. Analyzers used in this system are small portable structures that contain an electronic instrument to measure, record, and transmit relevant data on concentrations of the pollutants to a website. The model outcome for carbon monoxide obtained in functional tests in real conditions is also presented here. Data on temporal changes of carbon monoxide concentration are compared against meteorological parameters and speed of the vehicle. Spatial interpolation techniques are applied to obtain a nonplanar visualization of carbon monoxide and benzene concentrations in the main arteries of a city.

Residential proximity to major roads and term low birth weight: the roles of air pollution, heat, noise, and road-adjacent trees.

Science.gov (United States)

Dadvand, Payam; Ostro, Bart; Figueras, Francesc; Foraster, Maria; Basagaña, Xavier; Valentín, Antònia; Martinez, David; Beelen, Rob; Cirach, Marta; Hoek, Gerard; Jerrett, Michael; Brunekreef, Bert; Nieuwenhuijsen, Mark J

2014-07-01

Maternal residential proximity to roads has been associated with adverse pregnancy outcomes. However, there is no study investigating mediators or buffering effects of road-adjacent trees on this association. We investigated the association between mothers' residential proximity to major roads and term low birth weight (LBW), while exploring possible mediating roles of air pollution (PM(2.5), PM(2.5-10), PM(10), PM(2.5) absorbance, nitrogen dioxide, and nitrogen oxides), heat, and noise and buffering effect of road-adjacent trees on this association. This cohort study was based on 6438 singleton term births in Barcelona, Spain (2001-2005). Road proximity was measured as both continuous distance to and living within 200 m from a major road. We assessed individual exposures to air pollution, noise, and heat using, respectively, temporally adjusted land-use regression models, annual averages of 24-hour noise levels across 50 m and 250 m, and average of satellite-derived land-surface temperature in a 50-m buffer around each residential address. We used vegetation continuous fields to abstract tree coverage in a 200-m buffer around major roads. Living within 200 m of major roads was associated with a 46% increase in term LBW risk; an interquartile range increase in heat exposure with an 18% increase; and third-trimester exposure to PM(2.5), PM(2.5-10), and PM10 with 24%, 25%, and 26% increases, respectively. Air pollution and heat exposures together explained about one-third of the association between residential proximity to major roads and term LBW. Our observations on the buffering of this association by road-adjacent trees were not consistent between our 2 measures of proximity to major roads. An increased risk of term LBW associated with proximity to major roads was partly mediated by air pollution and heat exposures.

The CERN accelerator measurement database: on the road to federation

International Nuclear Information System (INIS)

Roderick, C.; Billen, R.; Gourber-Pace, M.; Hoibian, N.; Peryt, M.

2012-01-01

The Measurement database, acting as short-term central persistence and front-end of the CERN accelerator Logging Service, receives billions of time-series data per day for 200000+ signals. A variety of data acquisition systems on hundreds of front-end computers publish source data that eventually end up being logged in the Measurement database. As part of a federated approach to data management, information about source devices are defined in a Configuration database, whilst the signals to be logged are defined in the Measurement database. A mapping, which is often complex and subject to change/extension, is required in order to subscribe to the source devices, and write the published data to the corresponding named signals. Since 2005, this mapping was done by means of dozens of XML files, which were manually maintained by multiple persons, resulting in a configuration that was error prone. In 2010 this configuration was fully centralized in the Measurement database itself, reducing significantly the complexity and the actors in the process. Furthermore, logging processes immediately pick up modified configurations via JMS based notifications sent directly from the database. This paper will describe the architecture and the benefits of current implementation, as well as the next steps on the road to a fully federated solution. (authors)

Road safety in Poland: magnitude, causes and injuries.

Science.gov (United States)

Goniewicz, Krzysztof; Goniewicz, Mariusz; Pawłowski, Witold; Fiedor, Piotr; Lasota, Dorota

2017-01-01

Road accidents are a serious problem of the modern world. They are one of the main causes of injuries and are the third most frequent cause of death. Every year, about one million people, adults and children, die on the roads and several millions get injured. Mortality rate due to injuries from road accidents amounts to 2.2% of all deaths in the world. The research presents epidemiology of road accidents in the period 2004-2015 with particular emphasis on the key issues of road safety in Poland, related to the dangerous behaviour of road users (disregard toward traffic rules). Between years 2004 and 2015 on Polish roads took place more than 508000 accidents with 53155 fatalities and more then 572000 casualties. Despite the various measures which are taken to improve safety on Polish roads, the number of dead and wounded in the vehicle mishap is still large, and losses borne by society are high. To improve safety on Polish roads, it is necessary to continue multi- action plan to systematically progress in the level of road safety.

Ultra Low Noise Poroelastic Road Surfaces

Directory of Open Access Journals (Sweden)

Jerzy A. Ejsmont

2016-04-01

Full Text Available Noise is one of the most important environmental problems related to road traffic. During the last decades, the noise emitted by the engines and powertrains of vehicles was greatly reduced and tires became a clearly dominant noise source. The article describes the concept of low noise poroelastic road surfaces that are composed of mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and are much more flexible than standard asphalt or cement concrete pavements due to high content of rubber aggregate and elastic binder. Measurements performed in several European countries indicate that such surfaces decrease tire/road noise between 7 dB and 12 dB with respect to reference surfaces such as dense asphalt concrete or stone matrix asphalt. Furthermore, poroelastic road surfaces ascertain the rolling resistance of car tires, which is comparable to classic pavements. One of the unforeseen properties of the poroelastic road surfaces is their ability to decrease the risks related to car fires with fuel spills. The article presents the road and laboratory results of noise, rolling resistance, and fire tests performed on a few types of poroelastic road surfaces.

Measurement of LBE flow velocity profile by UDVP

International Nuclear Information System (INIS)

Kikuchi, Kenji; Takeda, Yasushi; Obayashi, Hiroo; Tezuka, Masao; Sato, Hiroshi

2006-01-01

Measurements of liquid metal lead-bismuth eutectic (LBE), flow velocity profile were realized in the spallation neutron source target model by the ultrasonic Doppler velocity profiler (UVDP) technique. So far, it has not been done well, because both of poor wetting property of LBE with stainless steels and poor performance of supersonic probes at high temperatures. The measurement was made for a return flow in the target model, which has coaxially arranged annular and tube channels, in the JAEA Lead Bismuth Loop-2 (JLBL-2). The surface treatment of LBE container was examined. It was found that the solder coating was effective to enhance an intensity of reflected ultrasonic wave. This treatment has been applied to the LBE loop, which was operated up to 150 deg. C. The electro magnetic pump generates LBE flow and the flow rate was measured by the electro magnetic flow meter. By changing the flow rate of LBE, velocity profiles in the target were measured. It was confirmed that the maximum velocity in the time-averaged velocity distribution on the target axis was proportional to the flow rate measured by the electro magnetic flow meter

EVALUATION ON THE SEISMIC RESPONSE CHARACTERISTICS OF A ROAD EMBANKMENT BASED ON THE MODERATE EARTHQUAKE OBSERVATION AND THE MICROTREMOR MEASUREMENT

Science.gov (United States)

Hata, Yoshiya; Ichii, Koji; Yamada, Masayuki; Tokida, Ken-Ichi; Takezawa, Koichiro; Shibao, Susumu; Mitsushita, Junji; Murata, Akira; Furukawa, Aiko; Koizumi, Keigo

Accurate evaluation on the seismic response characteristics of a road embankment is very important for the rational seismic assessment. However, in a lot of previous studies, the seismic response characteristics of an embankment were evaluated based on the results of shaking table test, centrifuge model test and dynamic FEM analysis. In this study, the transfer function and the shear wave velocity of a road embankment were evaluated based on the in-situ records of moderate earthquake observation and microtremor measurement. Test results show the possibility that the shear wave velocity of an embankment can be estimated by the earthquake observation or the microtremor measurement and the dynamic linear FEM analysis.

Dust emissions from unpaved roads on the Colorado Plateau

Science.gov (United States)

Duniway, M.; Flagg, C.; Belnap, J.

2013-12-01

On the Colorado Plateau, elevated levels of aeolian dust have become a major land management and policy concern due to its influence on climate, weather, terrestrial ecosystem dynamics, landscape development and fertility, melting of snow and ice, air quality, and human health. Most desert soil surfaces are stabilized by plants, rocks, and/or physical or biological soil crusts, but once disturbed, sediment production from these surfaces can increase dramatically. Road development and use is a common surface disturbing activity in the region. The extent and density of roads and road networks is rapidly increasing due to continued energy exploration, infrastructure development, and off-highway recreation activities. Though it is well known that unpaved roads produce dust, the relative contribution of dust from existing roads or the implications of future road development to regional dust loading is unknown. To address this need, we have initiated a multifaceted research effort to evaluating dust emissions from unpaved roads regionally. At 34 sites arranged across various road surfaces and soil textures in southeastern Utah, we are: 1) monitoring dust emissions, local wind conditions, and vehicle traffic and 2) evaluating fugitive dust potential using a portable wind tunnel and measuring road characteristics that affect dust production. We will then 3) develop a GIS-based model that integrates results from 1 & 2 to estimate potential dust contributions from current and future scenarios of regional road development. Passive, horizontal sediment traps were installed at three distances downwind from the road edge. One control trap was placed upwind of the samplers to account for local, non-road dust emissions. An electronic vehicle counter and anemometer were also installed at monitoring sites. Dust samples were collected every three months at fixed heights, 15 cm up to 100 cm above the soil surface, from March 2010 to the present. Threshold friction velocities (TFV

Pricing road use: politico-economic and fairness considerations

Energy Technology Data Exchange (ETDEWEB)

Oberholzer-Gee, F. [University of Pennsylvania, Pittsburgh (United States); Weck-Hannemann, H. [University of Innsbruck (Austria). Institute of of Public Finance

2002-09-01

Road pricing measures are rarely adopted in practice. In this review, we ask why citizens are not more supportive of road pricing. We identify two difficulties. First, the general public is often unwilling to embrace the price system as an allocation mechanism for scarce resources. Second, for politico-economic reasons, any latent support for road pricing schemes rarely translates into actual policy-making. Based on our analysis, we outline components of a road pricing policy that might receive greater electoral support. (author)

Velocity Profile measurements in two-phase flow using multi-wave sensors

Science.gov (United States)

Biddinika, M. K.; Ito, D.; Takahashi, H.; Kikura, H.; Aritomi, M.

2009-02-01

Two-phase flow has been recognized as one of the most important phenomena in fluid dynamics. In addition, gas-liquid two-phase flow appears in various industrial fields such as chemical industries and power generations. In order to clarify the flow structure, some flow parameters have been measured by using many effective measurement techniques. The velocity profile as one of the important flow parameter, has been measured by using ultrasonic velocity profile (UVP) technique. This technique can measure velocity distributions along a measuring line, which is a beam formed by pulse ultrasounds. Furthermore, a multi-wave sensor can measure the velocity profiles of both gas and liquid phase using UVP method. In this study, two types of multi-wave sensors are used. A sensor has cylindrical shape, and another one has square shape. The piezoelectric elements of each sensor have basic frequencies of 8 MHz for liquid phase and 2 MHz for gas phase, separately. The velocity profiles of air-water bubbly flow in a vertical rectangular channel were measured by using these multi-wave sensors, and the validation of the measuring accuracy was performed by the comparison between the velocity profiles measured by two multi-wave sensors.

Velocity Profile measurements in two-phase flow using multi-wave sensors

International Nuclear Information System (INIS)

Biddinika, M K; Ito, D; Takahashi, H; Kikura, H; Aritomi, M

2009-01-01

Two-phase flow has been recognized as one of the most important phenomena in fluid dynamics. In addition, gas-liquid two-phase flow appears in various industrial fields such as chemical industries and power generations. In order to clarify the flow structure, some flow parameters have been measured by using many effective measurement techniques. The velocity profile as one of the important flow parameter, has been measured by using ultrasonic velocity profile (UVP) technique. This technique can measure velocity distributions along a measuring line, which is a beam formed by pulse ultrasounds. Furthermore, a multi-wave sensor can measure the velocity profiles of both gas and liquid phase using UVP method. In this study, two types of multi-wave sensors are used. A sensor has cylindrical shape, and another one has square shape. The piezoelectric elements of each sensor have basic frequencies of 8 MHz for liquid phase and 2 MHz for gas phase, separately. The velocity profiles of air-water bubbly flow in a vertical rectangular channel were measured by using these multi-wave sensors, and the validation of the measuring accuracy was performed by the comparison between the velocity profiles measured by two multi-wave sensors.

How long do the dead survive on the road? Carcass persistence probability and implications for road-kill monitoring surveys.

Directory of Open Access Journals (Sweden)

Sara M Santos

conservation and transportation agencies with accurate numbers of road-kills, realistic mitigation measures, and detailed designs for road monitoring programs.

How long do the dead survive on the road? Carcass persistence probability and implications for road-kill monitoring surveys.

Science.gov (United States)

Santos, Sara M; Carvalho, Filipe; Mira, António

2011-01-01

-kills, realistic mitigation measures, and detailed designs for road monitoring programs.

Evaluation of Traffic Density Parameters as an Indicator of Vehicle Emission-Related Near-Road Air Pollution: A Case Study with NEXUS Measurement Data on Black Carbon.

Science.gov (United States)

Liu, Shi V; Chen, Fu-Lin; Xue, Jianping

2017-12-15

An important factor in evaluating health risk of near-road air pollution is to accurately estimate the traffic-related vehicle emission of air pollutants. Inclusion of traffic parameters such as road length/area, distance to roads, and traffic volume/intensity into models such as land use regression (LUR) models has improved exposure estimation. To better understand the relationship between vehicle emissions and near-road air pollution, we evaluated three traffic density-based indices: Major-Road Density (MRD), All-Traffic Density (ATD) and Heavy-Traffic Density (HTD) which represent the proportions of major roads, major road with annual average daily traffic (AADT), and major road with commercial annual average daily traffic (CAADT) in a buffered area, respectively. We evaluated the potential of these indices as vehicle emission-specific near-road air pollutant indicators by analyzing their correlation with black carbon (BC), a marker for mobile source air pollutants, using measurement data obtained from the Near-road Exposures and Effects of Urban Air Pollutants Study (NEXUS). The average BC concentrations during a day showed variations consistent with changes in traffic volume which were classified into high, medium, and low for the morning rush hours, the evening rush hours, and the rest of the day, respectively. The average correlation coefficients between BC concentrations and MRD, ATD, and HTD, were 0.26, 0.18, and 0.48, respectively, as compared with -0.31 and 0.25 for two commonly used traffic indicators: nearest distance to a major road and total length of the major road. HTD, which includes only heavy-duty diesel vehicles in its traffic count, gives statistically significant correlation coefficients for all near-road distances (50, 100, 150, 200, 250, and 300 m) that were analyzed. Generalized linear model (GLM) analyses show that season, traffic volume, HTD, and distance from major roads are highly related to BC measurements. Our analyses indicate that

Evaluation of Traffic Density Parameters as an Indicator of Vehicle Emission-Related Near-Road Air Pollution: A Case Study with NEXUS Measurement Data on Black Carbon

Directory of Open Access Journals (Sweden)

Shi V. Liu

2017-12-01

Full Text Available An important factor in evaluating health risk of near-road air pollution is to accurately estimate the traffic-related vehicle emission of air pollutants. Inclusion of traffic parameters such as road length/area, distance to roads, and traffic volume/intensity into models such as land use regression (LUR models has improved exposure estimation. To better understand the relationship between vehicle emissions and near-road air pollution, we evaluated three traffic density-based indices: Major-Road Density (MRD, All-Traffic Density (ATD and Heavy-Traffic Density (HTD which represent the proportions of major roads, major road with annual average daily traffic (AADT, and major road with commercial annual average daily traffic (CAADT in a buffered area, respectively. We evaluated the potential of these indices as vehicle emission-specific near-road air pollutant indicators by analyzing their correlation with black carbon (BC, a marker for mobile source air pollutants, using measurement data obtained from the Near-road Exposures and Effects of Urban Air Pollutants Study (NEXUS. The average BC concentrations during a day showed variations consistent with changes in traffic volume which were classified into high, medium, and low for the morning rush hours, the evening rush hours, and the rest of the day, respectively. The average correlation coefficients between BC concentrations and MRD, ATD, and HTD, were 0.26, 0.18, and 0.48, respectively, as compared with −0.31 and 0.25 for two commonly used traffic indicators: nearest distance to a major road and total length of the major road. HTD, which includes only heavy-duty diesel vehicles in its traffic count, gives statistically significant correlation coefficients for all near-road distances (50, 100, 150, 200, 250, and 300 m that were analyzed. Generalized linear model (GLM analyses show that season, traffic volume, HTD, and distance from major roads are highly related to BC measurements. Our analyses

The importance of accurate road data for spatial applications in public health: customizing a road network

Directory of Open Access Journals (Sweden)

Laraia Barbara A

2009-05-01

Full Text Available Abstract Background Health researchers have increasingly adopted the use of geographic information systems (GIS for analyzing environments in which people live and how those environments affect health. One aspect of this research that is often overlooked is the quality and detail of the road data and whether or not it is appropriate for the scale of analysis. Many readily available road datasets, both public domain and commercial, contain positional errors or generalizations that may not be compatible with highly accurate geospatial locations. This study examined the accuracy, completeness, and currency of four readily available public and commercial sources for road data (North Carolina Department of Transportation, StreetMap Pro, TIGER/Line 2000, TIGER/Line 2007 relative to a custom road dataset which we developed and used for comparison. Methods and Results A custom road network dataset was developed to examine associations between health behaviors and the environment among pregnant and postpartum women living in central North Carolina in the United States. Three analytical measures were developed to assess the comparative accuracy and utility of four publicly and commercially available road datasets and the custom dataset in relation to participants' residential locations over three time periods. The exclusion of road segments and positional errors in the four comparison road datasets resulted in between 5.9% and 64.4% of respondents lying farther than 15.24 meters from their nearest road, the distance of the threshold set by the project to facilitate spatial analysis. Agreement, using a Pearson's correlation coefficient, between the customized road dataset and the four comparison road datasets ranged from 0.01 to 0.82. Conclusion This study demonstrates the importance of examining available road datasets and assessing their completeness, accuracy, and currency for their particular study area. This paper serves as an example for assessing

Runoff and windblown vehicle spray from road surfaces, risks and measures for soil and water.

NARCIS (Netherlands)

Schipper, P.N.M.; Comans, R.N.J.; Dijkstra, J.J.; Vergouwen, L.

2007-01-01

Soil and surface water along roads are exposed to pollution from motorways. The main pollutants are polycyclic aromatic hydrocarbons (PAH), mineral oil, heavy metals and salt. These pollutants originate from vehicles (fuel, wires, leakage), wear and degradation of road surfaces and road furniture

Impact of road traffic accidents on the elderly.

Science.gov (United States)

Etehad, H; Yousefzadeh-Chabok, Sh; Davoudi-Kiakalaye, A; Moghadam Dehnadi, A; Hemati, H; Mohtasham-Amiri, Z

2015-01-01

Older adults are a vulnerable road user group with high mortality and morbidity in road crash. The aim of this study was to show pattern of road traffic injuries in this special aging group. In a cross sectional study, pre-hospital emergency system reports, hospital and police records of all motor vehicle collisions injured above 60 years old who were admitted to Pour-Sina hospital from April 2011 to March 2012 were studied. Demographic data, characteristic of road traffic incidents and in-hospital medical profiles were derived. Data were analyzed with SPSS ver. 18. Differences between demographic and injuries situation were calculated by chi square test. A p-value of road accident injured. Mean age of them was 70.9 ± 6.7 years. Most of them were male (74.7%). 40.5% were pedestrians, 22.1% were car occupants and 19.1% were motorcyclists.76.7% had multiple trauma. Head and neck were the most prevalent regions of injured. Total in-hospital mortality rate was 10.1% that was higher in old elderly pedestrians and motorcyclists in comparison to young elderly (16.1% vs. 7.9%) and other type of victims (ρroad accident injured. Mean age of them was 70.9 ± 6.7 years. Most of them were male (74.7%). 40.5% were pedestrians, 22.1% were car occupants and 19.1% were motorcyclists.76.7% had multiple trauma. Head and neck were the most prevalent regions of injured. Total in-hospital mortality rate was 10.1% that was higher in old elderly pedestrians and motorcyclists in comparison to young elderly (16.1% vs. 7.9%) and other type of victims (ρroad traffic injuries in this group especially in pedestrians should be taken into consideration and strategies aimed at the road-user safety including periodic medical examination and improvement of road structure and facilities. Copyright © 2015. Published by Elsevier Ireland Ltd.

STUDY OF ROAD TRAFFIC ACCIDENTS WITH SPECIAL REFERENCE TO THE ACCIDENT VICTIMS ADMITTED IN GAUHATI MEDICAL COLLEGE AND HOSPITAL, ASSAM

Directory of Open Access Journals (Sweden)

Rocket Chandra

2016-05-01

Full Text Available BACKGROUND In the present scenario, road traffic accidents have become a major cause of human mortality and morbidity. Accidents are increasing at alarming rates in India. The objective of our study was to assess the socio-demographic profile of road traffic accident victims admitted in a tertiary care setting, and to assess the pattern of injuries. METHODOLOGY The present study is prospective and analytical hospital based study. RESULTS The present studies show that more than 70% of the victims are in the age group of below 45 years (n=3196 and with male preponderance. Out of 14364 accident patients visiting the emergency department of Gauhati Medical College and Hospital, 4953 patients were admitted. The majorities of the patients (n=2995 were admitted in surgery department and 1586 in orthopaedic department. CONCLUSIONS Several factors are responsible for causing road accidents such as drunk driving, lack of awareness of traffic rules, nonadherence to safety measures. To reduce morbidity and mortality following road accidents, comprehensive policy has to be adopted by the government

Distributed road assessment system

Science.gov (United States)

Beer, N. Reginald; Paglieroni, David W

2014-03-25

A system that detects damage on or below the surface of a paved structure or pavement is provided. A distributed road assessment system includes road assessment pods and a road assessment server. Each road assessment pod includes a ground-penetrating radar antenna array and a detection system that detects road damage from the return signals as the vehicle on which the pod is mounted travels down a road. Each road assessment pod transmits to the road assessment server occurrence information describing each occurrence of road damage that is newly detected on a current scan of a road. The road assessment server maintains a road damage database of occurrence information describing the previously detected occurrences of road damage. After the road assessment server receives occurrence information for newly detected occurrences of road damage for a portion of a road, the road assessment server determines which newly detected occurrences correspond to which previously detected occurrences of road damage.

Quantifying road dust resuspension in urban environment by Multilinear Engine: A comparison with PMF2

Science.gov (United States)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

Atmospheric PM pollution from traffic comprises not only direct emissions but also non-exhaust emissions because resuspension of road dust that can produce high human exposure to heavy metals, metalloids, and mineral matter. A key task for establishing mitigation or preventive measures is estimating the contribution of road dust resuspension to the atmospheric PM mixture. Several source apportionment studies, applying receptor modeling at urban background sites, have shown the difficulty in identifying a road dust source separately from other mineral sources or vehicular exhausts. The Multilinear Engine (ME-2) is a computer program that can solve the Positive Matrix Factorization (PMF) problem. ME-2 uses a programming language permitting the solution to be guided toward some possible targets that can be derived from a priori knowledge of sources (chemical profile, ratios, etc.). This feature makes it especially suitable for source apportionment studies where partial knowledge of the sources is available. In the present study ME-2 was applied to data from an urban background site of Barcelona (Spain) to quantify the contribution of road dust resuspension to PM 10 and PM 2.5 concentrations. Given that recently the emission profile of local resuspended road dust was obtained (Amato, F., Pandolfi, M., Viana, M., Querol, X., Alastuey, A., Moreno, T., 2009. Spatial and chemical patterns of PM 10 in road dust deposited in urban environment. Atmospheric Environment 43 (9), 1650-1659), such a priori information was introduced in the model as auxiliary terms of the object function to be minimized by the implementation of the so-called "pulling equations". ME-2 permitted to enhance the basic PMF solution (obtained by PMF2) identifying, beside the seven sources of PMF2, the road dust source which accounted for 6.9 μg m -3 (17%) in PM 10, 2.2 μg m -3 (8%) of PM 2.5 and 0.3 μg m -3 (2%) of PM 1. This reveals that resuspension was responsible of the 37%, 15% and 3% of total

The causes and prevalence of road traffic accidents amongst ...

African Journals Online (AJOL)

The study showed a prevalence of road traffic accidents of 47.9% in Benin City occurring more in day time and the common causes of road traffic accidents include careless driving, speed violation, brake failure, traffic violations, faulty overtaking, burst tyre, bad roads, alcohol use and armed robbery attack. Thus measures ...

Real-world operation conditions and on-road emissions of Beijing diesel buses measured by using portable emission measurement system and electric low-pressure impactor.

Science.gov (United States)

Liu, Zhihua; Ge, Yunshan; Johnson, Kent C; Shah, Asad Naeem; Tan, Jianwei; Wang, Chu; Yu, Linxiao

2011-03-15

On-road measurement is an effective method to investigate real-world emissions generated from vehicles and estimate the difference between engine certification cycles and real-world operating conditions. This study presents the results of on-road measurements collected from urban buses which propelled by diesel engine in Beijing city. Two widely used Euro III emission level buses and two Euro IV emission level buses were chosen to perform on-road emission measurements using portable emission measurement system (PEMS) for gaseous pollutant and Electric Low Pressure Impactor (ELPI) for particulate matter (PM) number emissions. The results indicate that considerable discrepancies of engine operating conditions between real-world driving cycles and engine certification cycles have been observed. Under real-world operating conditions, carbon monoxide (CO) and hydrocarbon (HC) emissions can easily meet their respective regulations limits, while brake specification nitrogen oxide (bsNO(x)) emissions present a significant deviation from its corresponding limit. Compared with standard limits, the real-world bsNO(x) emission of the two Euro III emission level buses approximately increased by 60% and 120% respectively, and bsNO(x) of two Euro IV buses nearly twice standard limits because Selective Catalytic Reduction (SCR) system not active under low exhaust temperature. Particle mass were estimated via particle size distribution with the assumption that particle density and diameter is liner. The results demonstrate that nanometer size particulate matter make significant contribution to total particle number but play a minor role to total particle mass. It is suggested that specific certified cycle should be developed to regulate bus engines emissions on the test bench or use PEMS to control the bus emissions under real-world operating conditions. Copyright © 2010 Elsevier B.V. All rights reserved.

Extended investigation on road fatality in Brunei.

Science.gov (United States)

Yusof, N B; Hoque, M A; Steele, M C; Yong, S Y

2018-06-08

Road fatality is one of the leading causes of death in Brunei with 79 deaths in 1993, the highest ever recorded. The Brunei government has been trying to reduce this by implementing new traffic measures and successfully reduced fatalities to 24 fatalities in 2014. Yearly road fatality has been fluctuating, but there has been a declining tendency overall. The aim of this study is to investigate road fatality in Brunei by extending the research. We developed a multiple regression model and carried out an analysis on road fatality in Brunei. Our analysis indicates that the road fatality appears to rise depending on the increase in the number of young drivers between 15 to 24 years and the number of unemployed people. Comparisons of Brunei road fatality rate per 10,000 vehicles are made with some other countries and we conclude that Brunei has approximately the same rate as Australia in 2014.

AN INVESTIGATION ON THE FOREST ROAD PLANNING AND ROAD GROUND

Directory of Open Access Journals (Sweden)

Hafız Hulusi ACAR

2001-01-01

Full Text Available It is required that the capital used for construction of road must be technical, economical and used in its location. For this reason, the projects must be prepared for forest roads and all operations belong to roads must be guided according to these projects. In this investigation, available forest road network plan and constructed forest roads were investigated at the point of view technical and forest transportation. After this, it were studied to reach the highest exploitation rate as can as possible. Available forest road density were found as 11.9 m/ha in forest areas for Yesiltepe District. In this condition, exploitation rate was 78 %. After that, optimum forest road network were planned and road density were reached to 22 m/ha and exploitation rate to 86 %. Directed sample method were used from taking soil sample methods and samples were took in mixed system. According to results of the experiments, available forest roads were found in a good degree at the point of view endurance, pressing and transportation capacity. With these results, it is aimed to reach higher exploitation rate with given attention to landslide areas during planning of forest roads on the mountain areas such as Black Sea Region. For this reason, required importance must be given to planning of truck and logging roads. Ground analysis must be done and took care before during planning process of forest road network.

EPA GHG Certification of Medium- and Heavy-Duty Vehicles: Development of Road Grade Profiles Representative of US Controlled Access Highways

Energy Technology Data Exchange (ETDEWEB)

Wood, Eric [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Duran, Adam [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Burton, Evan [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gonder, Jeffrey [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kelly, Kenneth [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2015-05-12

This report includes a detailed comparison of the TomTom national road grade database relative to a local road grade dataset generated by Southwest Research Institute and a national elevation dataset publically available from the U.S. Geological Survey. This analysis concluded that the TomTom national road grade database was a suitable source of road grade data for purposes of this study.

Constraining CO2 tower measurements in an inhomogeneous area with anthropogenic emissions using a combination of car-mounted instrument campaigns, aircraft profiles, transport modeling and neural networks

Science.gov (United States)

Schmidt, A.; Rella, C.; Conley, S. A.; Goeckede, M.; Law, B. E.

2013-12-01

The NOAA CO2 observation network in Oregon has been enhanced by 3 new towers in 2012. The tallest tower in the network (270 m), located in Silverton in the Willamette Valley is affected by anthropogenic emissions from Oregon's busiest traffic routes and urban centers. In summer 2012, we conducted a measurement campaign using a car-mounted PICARRO CRDS CO2/CO analyzer. Over 3 days, the instrument was driven over 1000 miles throughout the northwestern portion of Oregon measuring the CO/ CO2 ratios on main highways, back roads in forests, agricultural sites, and Oregon's biggest urban centers. By geospatial analyses we obtained ratios of CO/ CO2 over distinct land cover types divided into 10 classes represented in the study area. Using the coupled WRF-STILT transport model we calculated the footprints of nearby CO/ CO2 observation towers for the corresponding days of mobile road measurements. Spatiotemporally assigned source areas in combination with the land use classification were then used to calculate specific ratios of CO (anthropogenic origins) and CO2 to separate the anthropogenic portion of CO2 from the mixing ratio time series measured at the tower in Silverton. The WRF modeled boundary layer heights used in out study showed some differences compared to the boundary layer heights derived from profile data of wind, temperature, and humidity measured with an airplane in August, September, and November 2012, repeatedly over 5 tower locations. A Bayesian Regularized Artificial Neural Network (BRANN) was used to correct the boundary layer height calculated with WRF with a temporal resolution of 20 minutes and a horizontal resolution of 4 km. For that purpose the BRANN was trained using height profile data from the flight campaigns and spatiotemporally corresponding meteorological data from WRF. Our analyses provide information needed to run inverse modeling of CO2 exchange in an area that is affected by sources that cannot easily be considered by biospheric models

Miscellaneous Roads

Data.gov (United States)

Minnesota Department of Natural Resources — This data set contains roadway centerlines for miscellanous roads, a catch-all category for all road types not present in the other DNR derived products. These road...

Applicability of models to estimate traffic noise for urban roads.

Science.gov (United States)

Melo, Ricardo A; Pimentel, Roberto L; Lacerda, Diego M; Silva, Wekisley M

2015-01-01

Traffic noise is a highly relevant environmental impact in cities. Models to estimate traffic noise, in turn, can be useful tools to guide mitigation measures. In this paper, the applicability of models to estimate noise levels produced by a continuous flow of vehicles on urban roads is investigated. The aim is to identify which models are more appropriate to estimate traffic noise in urban areas since several models available were conceived to estimate noise from highway traffic. First, measurements of traffic noise, vehicle count and speed were carried out in five arterial urban roads of a brazilian city. Together with geometric measurements of width of lanes and distance from noise meter to lanes, these data were input in several models to estimate traffic noise. The predicted noise levels were then compared to the respective measured counterparts for each road investigated. In addition, a chart showing mean differences in noise between estimations and measurements is presented, to evaluate the overall performance of the models. Measured Leq values varied from 69 to 79 dB(A) for traffic flows varying from 1618 to 5220 vehicles/h. Mean noise level differences between estimations and measurements for all urban roads investigated ranged from -3.5 to 5.5 dB(A). According to the results, deficiencies of some models are discussed while other models are identified as applicable to noise estimations on urban roads in a condition of continuous flow. Key issues to apply such models to urban roads are highlighted.

Study on profile measurement of extruding tire tread by laser

Science.gov (United States)

Wang, LiangCai; Zhang, Wanping; Zhu, Weihu

1996-10-01

This paper presents a new 2D measuring system-profile measurement of extruding tire tread by laser. It includes the thickness measurement of extruding tire tread by laser and the width measurement of extruding tire tread using Moire Fringe. The system has been applied to process line of extruding tire tread. Two measuring results have been obtained. One is a standard profile picture of extruding tire tread including seven measuring values. Another one is a series of thickness and width values. When the scanning speed thickness range is thickness < +/- 0.1mm.

The Skid Resistance Evaluation on the Longterm Monitored Road Sections

Directory of Open Access Journals (Sweden)

Kotek Peter

2014-12-01

Full Text Available The article deals with the analysis of the skid resistance results measured at the long-term monitored road sections in Slovakia in perspective of the possibility of the deterioration functions determination for the purposes of the pavement management system. There were 11 road sections evaluated, on which have been surface characteristics measured since 1998. The focus was on the evaluation of the longitudinal friction coefficient Mu measured by device Skiddometer BV11, which is the property of the Slovak Road Administration. Beside the Mu parameter, the test conditions were observed and evaluated, as well (measured speed, air and surface temperature, type of asphalts of the wearing course, traffic load, and the season (spring, autumn, respectively in which the skid resistance measurements were performed. In conclusion, there was reviewed a presumption of the possibility to determine a deterioration functions for skid resistance in point of view the quality of the data, which have been collected on the Slovak long-term monitored road sections.

Invasive Brown Treesnake movements at road edges indicate road-crossing avoidance

Science.gov (United States)

Siers, Shane R.; Savidge, Julie S; Reed, Robert N.

2014-01-01

Roads have significant impacts on the dispersal of wildlife. Although this poses a threat to the abundance and diversity of desirable flora and fauna, it also affords some opportunity for enhancing control of invasive species. Roads are the most common terrain features that may affect the rate of landscape-scale movements of invasive Brown Treesnakes (Boiga irregularis) throughout Guam. We radio tracked 45 free-ranging Brown Treesnakes in close proximity to two roads in Guam and recorded instances where daily relocations of snakes spanned roads. Then we reconstructed observed movement histories with randomized turning angles, which served as a useful null hypothesis for assessing the effect of roads or road edge habitat on Brown Treesnake movement patterns. Random walk simulations demonstrated that Brown Treesnakes crossed these roads at a rate far lower than would be expected if snake movement was random with respect to roads and road edge habitat. We discuss two alternative hypotheses for these results: 1) habitat gaps posed by roads physically or behaviorally restrict snake movement; or 2) road edges provide preferred foraging habitat from which snakes are reluctant to depart. Because roads often form the boundaries of jurisdictional and management units, the effects of roads on the movement of invasive Brown Treesnakes will influence the prospects for success of future landscape-level suppression efforts.

Whole-body profile scanner for in vivo quantitative activity measurement

International Nuclear Information System (INIS)

Bergmann, H.

1978-01-01

A whole-body profile scanner has been developed by fitting parallel slit collimators to a shadow shield whole-body counter. Sensitivity, uniformity and resolution measurements were performed using a number of different counting conditions. It is shown that improved accuracy of activity measurements is obtained by using a wide window counting technique for low and medium energy gamma emitters (99m Tc, 131 I), whereas a photopeak window should be used for high energy gamma emitters (47 Ca). Due to the finite spatial resolution of the system a systematic error in evaluating regional activities from the counting rate profile occurs which is characterized by a spatial spillover factor. The spatial spillover factor is measured and is subsequently used to calculate the error on basis of a simple model. It is shown that only small errors are caused by spatial spillover when the length of a region is at least three times the full width half maximum of the point spread function. Applying the above mentioned simple rules it is concluded that profile scanning is a sensitive and accurate technique for activity measurements in vivo. Two examples of clinical applications (measurement of bone accretion rates of calcium and Tc-pyrophosphate, regional radioiodine retention in patients with thyroid carcinoma) and a review of the papers on profile scanning demonstrate the types of investigations in which profile scanning is superior to alternative techniques. (author)

Chloride ingress profiles measured by electron probe micro analysis

DEFF Research Database (Denmark)

Jensen, Ole mejlhede; Coats, Alison M.; Glasser, Fred P.

1996-01-01

Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA is demonst......Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA...... is demonstated to determine chloride ingress in cement paste on a micrometer scale. Potential chloride ingress routes such as cracks or the paste-aggregate interface may also be characterized by EPMA. Copyright (C) 1996 Elsevier Science Ltd...

Influence of solid noise barriers on near-road and on-road air quality

Science.gov (United States)

Baldauf, Richard W.; Isakov, Vlad; Deshmukh, Parikshit; Venkatram, Akula; Yang, Bo; Zhang, K. Max

2016-03-01

Public health concerns regarding adverse health effects for populations spending significant amounts of time near high traffic roadways has increased substantially in recent years. Roadside features, including solid noise barriers, have been investigated as potential methods that can be implemented in a relatively short time period to reduce air pollution exposures from nearby traffic. A field study was conducted to determine the influence of noise barriers on both on-road and downwind pollutant concentrations near a large highway in Phoenix, Arizona, USA. Concentrations of nitrogen dioxide, carbon monoxide, ultrafine particles, and black carbon were measured using a mobile platform and fixed sites along two limited-access stretches of highway that contained a section of noise barrier and a section with no noise barrier at-grade with the surrounding terrain. Results of the study showed that pollutant concentrations behind the roadside barriers were significantly lower relative to those measured in the absence of barriers. The reductions ranged from 50% within 50 m from the barrier to about 30% as far as 300 m from the barrier. Reductions in pollutant concentrations generally began within the first 50 m of the barrier edge; however, concentrations were highly variable due to vehicle activity behind the barrier and along nearby urban arterial roadways. The concentrations on the highway, upwind of the barrier, varied depending on wind direction. Overall, the on-road concentrations in front of the noise barrier were similar to those measured in the absence of the barrier, contradicting previous modeling results that suggested roadside barriers increase pollutant levels on the road. Thus, this study suggests that noise barriers do reduce potential pollutant exposures for populations downwind of the road, and do not likely increase exposures to traffic-related pollutants for vehicle passengers on the highway.

Modeling of passengers' safety perception for buses on mountainous roads.

Science.gov (United States)

Khoo, Hooi Ling; Ahmed, Muaid

2018-04-01

This study had developed a passenger safety perception model specifically for buses taking into consideration the various factors, namely driver characteristics, environmental conditions, and bus characteristics using Bayesian Network. The behaviour of bus driver is observed through the bus motion profile, measured in longitudinal, lateral, and vertical accelerations. The road geometry is recorded using GPS and is computed with the aid of the Google map while the perceived bus safety is rated by the passengers in the bus in real time. A total of 13 variables were derived and used in the model development. The developed Bayesian Network model shows that the type of bus and the experience of the driver on the investigated route could have an influence on passenger's perception of their safety on buses. Road geometry is an indirect influencing factor through the driver's behavior. The findings of this model are useful for the authorities to structure an effective strategy to improve the level of perceived bus safety. A high level of bus safety will definitely boost passenger usage confidence which will subsequently increase ridership. Copyright © 2018 Elsevier Ltd. All rights reserved.

Atmospheric profiles from active space-based radio measurements

Science.gov (United States)

Hardy, Kenneth R.; Hinson, David P.; Tyler, G. L.; Kursinski, E. R.

1992-01-01

The paper describes determinations of atmospheric profiles from space-based radio measurements and the retrieval methodology used, with special attention given to the measurement procedure and the characteristics of the soundings. It is speculated that reliable profiles of the terrestrial atmosphere can be obtained by the occultation technique from the surface to a height of about 60 km. With the full complement of 21 the Global Positioning System (GPS) satellites and one GPS receiver in sun synchronous polar orbit, a maximum of 42 soundings could be obtained for each complete orbit or about 670 per day, providing almost uniform global coverage.

Excursions out-of-lane versus standard deviation of lateral position as outcome measure of the on-the-road driving test

NARCIS (Netherlands)

Verster, Joris C; Roth, Thomas

BACKGROUND: The traditional outcome measure of the Dutch on-the-road driving test is the standard deviation of lateral position (SDLP), the weaving of the car. This paper explores whether excursions out-of-lane are a suitable additional outcome measure to index driving impairment. METHODS: A

Who is in control of road safety? A STAMP control structure analysis of the road transport system in Queensland, Australia.

Science.gov (United States)

Salmon, Paul M; Read, Gemma J M; Stevens, Nicholas J

2016-11-01

Despite significant progress, road trauma continues to represent a global safety issue. In Queensland (Qld), Australia, there is currently a focus on preventing the 'fatal five' behaviours underpinning road trauma (drug and drink driving, distraction, seat belt wearing, speeding, and fatigue), along with an emphasis on a shared responsibility for road safety that spans road users, vehicle manufacturers, designers, policy makers etc. The aim of this article is to clarify who shares the responsibility for road safety in Qld and to determine what control measures are enacted to prevent the fatal five behaviours. This is achieved through the presentation of a control structure model that depicts the actors and organisations within the Qld road transport system along with the control and feedback relationships that exist between them. Validated through a Delphi study, the model shows a diverse set of actors and organisations who share the responsibility for road safety that goes beyond those discussed in road safety policies and strategies. The analysis also shows that, compared to other safety critical domains, there are less formal control structures in road transport and that opportunities exist to add new controls and strengthen existing ones. Relationships that influence rather than control are also prominent. Finally, when compared to other safety critical domains, the strength of road safety controls is brought into question. Copyright © 2016 Elsevier Ltd. All rights reserved.

Profile of non-fatal injuries due to road traffic accidents from a industrial town in India.

Science.gov (United States)

Bayan, Pankaj; Bhawalkar, J S; Jadhav, S L; Banerjee, Amitav

2013-01-01

India has one of the highest road traffic accident rates in the world. To lessen this burden, information on the contributing factors is necessary. We studied a series of cases of non-fatal road traffic accidents in two tertiary care hospitals in Pimpri, Pune, India. A total of 212 non-fatal road traffic accidents admitted over a period of one year in these two hospitals constituted the study sample. The study variables were, the gender of the accident victims, mode of accident, days of week on which the accident took place, time of day when the injury was sustained, part of the body injured, nature of injury, and self-reported reasons for the accident. data were summarized using percentages. The Chi-square test for goodness of fit was applied, to see whether there was any association between the different weekdays or time of day and the accidents. MALE : female ratio was almost 5 : 1, which was statistically significant (Chi-Square for goodness of fit = 95.11, df = 1, P accidents occurred on Sundays and Mondays and the least around midweek (Wednesday). This pattern was also statistically significant (Chi-square for goodness of fit = 30.09, df = 6, P road users contributed to almost 80% of the cases of Road Traffic Injuries (RTIs). Accidents were more likely in the time zone of 8 pm to midnight, followed by 4 pm to 8 pm (Chi-square for goodness of fit = 89.58, df = 5, P accident. Almost half (46.22%) of the injured admitted to drinking alcohol on a regular basis. Wide pavements and safe zebra crossings should be provided for pedestrians, as the highest casualty in this study were pedestrians. More accidents occurred on Sundays and Mondays and in the late evenings. Extra supervision by traffic police may be considered on Sundays / Holidays and the day following. Roads should be well lit to improve visibility after sunset.

New law puts Bolivian biodiversity hotspot on road to deforestation.

Science.gov (United States)

Fernández-Llamazares, Álvaro; Helle, Joose; Eklund, Johanna; Balmford, Andrew; Mónica Moraes, R; Reyes-García, Victoria; Cabeza, Mar

2018-01-08

In August 2017, the Bolivian government passed a contentious law downgrading the legal protection of the Isiboro-Sécure National Park and Indigenous Territory (TIPNIS, for its Spanish acronym), the ancestral homeland of four lowland indigenous groups and one of Bolivia's most iconic protected areas. Due to its strategic position straddling the Andes and Amazonia, TIPNIS represents not only a key biodiversity hotspot in Bolivia, but one of the most biodiverse regions on Earth, harboring exceptional levels of endemism and globally important populations of megafauna, as well as protecting substantial topographic complexity likely to support both wildlife migration and species range shifts in response to climate change [1]. The new law, set to authorize the construction of a deeply-contested road through the core of the park, has reopened one of the highest profile socio-environmental conflicts in Latin America. Roads in tropical forests often lead to habitat conversion, and indeed within TIPNIS more than 58% of deforestation is concentrated 5 km or less away from existing roads. It, therefore, seems very likely that the planned road will magnify the current scale and pace of deforestation in TIPNIS, underscoring the urgent need for revisiting the road plans. Copyright © 2017 Elsevier Ltd. All rights reserved.

Physiological demands of off-road vehicle riding.

Science.gov (United States)

Burr, Jamie F; Jamnik, Veronica K; Shaw, Jim A; Gledhill, Norman

2010-07-01

The purpose of this study was to characterize the physiological demands of recreational off-road vehicle riding under typical riding conditions using habitual recreational off-road vehicle riders (n = 128). Comparisons of the physical demands of off-road vehicle riding were made between vehicle types (all-terrain vehicle (ATV) and off-road motorcycle (ORM)) to the demands of common recreational activities. Habitual riders (ATV = 56, ORM = 72) performed strength assessments before and after a representative trail ride (48 +/- 24.2 min), and ambulatory oxygen consumption was measured during one lap (24.2 +/- 11.8 min) of the ride. The mean VO2 requirement (mL x kg(-1) x min(-1)) while riding an off-road vehicle was 12.1 +/- 4.9 for ATV and 21.3 +/- 7.1 for ORM (P = 0.002), which is comparable to the VO2 required of many common recreational activities. Temporal analysis of activity intensity revealed approximately 14% of an ATV ride and 38% of an ORM ride are within the intensity range (940% VO2 reserve) required to achieve changes in aerobic fitness. Riding on a representative course also led to muscular fatigue, particularly in the upper body. On the basis of the measured metabolic demands, evidence of muscular strength requirements, and the associated caloric expenditures with off-road vehicle riding, this alternative form of activity conforms to the recommended physical activity guidelines and can be effective for achieving beneficial changes in health and fitness.

Individual spatial responses towards roads: implications for mortality risk.

Directory of Open Access Journals (Sweden)

Clara Grilo

Full Text Available BACKGROUND: Understanding the ecological consequences of roads and developing ways to mitigate their negative effects has become an important goal for many conservation biologists. Most mitigation measures are based on road mortality and barrier effects data. However, studying fine-scale individual spatial responses in roaded landscapes may help develop more cohesive road planning strategies for wildlife conservation. METHODOLOGY/PRINCIPAL FINDINGS: We investigated how individuals respond in their spatial behavior toward a highway and its traffic intensity by radio-tracking two common species particularly vulnerable to road mortality (barn owl Tyto alba and stone marten Martes foina. We addressed the following questions: 1 how highways affected home-range location and size in the immediate vicinity of these structures, 2 which road-related features influenced habitat selection, 3 what was the role of different road-related features on movement properties, and 4 which characteristics were associated with crossing events and road-kills. The main findings were: 1 if there was available habitat, barn owls and stone martens may not avoid highways and may even include highways within their home-ranges; 2 both species avoided using areas near the highway when traffic was high, but tended to move toward the highway when streams were in close proximity and where verges offered suitable habitat; and 3 barn owls tended to cross above-grade highway sections while stone martens tended to avoid crossing at leveled highway sections. CONCLUSIONS: Mortality may be the main road-mediated mechanism that affects barn owl and stone marten populations. Fine-scale movements strongly indicated that a decrease in road mortality risk can be realized by reducing sources of attraction, and by increasing road permeability through measures that promote safe crossings.

Distributed Road Grade Estimation for Heavy Duty Vehicles

Energy Technology Data Exchange (ETDEWEB)

Sahlholm, Per

2011-07-01

An increasing need for goods and passenger transportation drives continued worldwide growth in traffic. As traffic increases environmental concerns, traffic safety, and cost efficiency become ever more important. Advancements in microelectronics open the possibility to address these issues through new advanced driver assistance systems. Applications such as predictive cruise control, automated gearbox control, predictive front lighting control, and hybrid vehicle state-of-charge control decrease the energy consumption of vehicles and increase the safety. These control systems can benefit significantly from preview road grade information. This information is currently obtained using specialized survey vehicles, and is not widely available. This thesis proposes new methods to obtain road grade information using on-board sensors. The task of creating road grade maps is addressed by the proposal of a framework where vehicles using a road network collect the necessary data for estimating the road grade. The estimation can then be carried out locally in the vehicle, or in the presence of a communication link to the infrastructure, centrally. In either case the accuracy of the map increases over time, and costly road surveys can be avoided. This thesis presents a new distributed method for creating accurate road grade maps for vehicle control applications. Standard heavy duty vehicles in normal operation are used to collect measurements. Estimates from multiple passes along a road segment are merged to form a road grade map, which improves each time a vehicle retraces a route. The design and implementation of the road grade estimator are described, and the performance is experimentally evaluated using real vehicles. Three different grade estimation methods, based on different assumption on the road grade signal, are proposed and compared. They all use data from sensors that are standard equipment in heavy duty vehicles. Measurements of the vehicle speed and the engine

Road Service Performance Based On Integrated Road Design Consistency (IC) Along Federal Road F0023

OpenAIRE

Zainal Zaffan Farhana; Prasetijo Joewono; Musa Wan Zahidah

2017-01-01

Road accidents are one of the world’s largest public health and injury prevention problems. In Malaysia, the west coast area of Malaysia been stated as the highest motorcycle fatalities and road accidents are one of the factors that cause of death and injuries in this country. The most common fatal accident is between a motorcycle and passenger car. The most of the fatal accidents happened on Federal roads with 44 fatal accidents reported, which is equal to 29%. Lacks of road geometric design...

Predictability by recognizable road design. [previously called: Recognizable road design.

NARCIS (Netherlands)

2007-01-01

One of the Sustainable Safety principles is that a road should have a recognizable design and a predictable alignment. If this is the case, road users know how they are expected to behave and what they can expect from other road users, so that crashes may be prevented. For roads to be recognizable,

Driving cycles for measuring passenger car emissions on roads with traffic calming measures

International Nuclear Information System (INIS)

Boulter, P.G.; Latham, S.; Ainge, M.

1999-01-01

Although local authorities in the UK need to be aware of any air quality impacts resulting from their traffic calming operations, there is little information relating to the effects of different traffic calming measures. The effects on air quality on this scale are complex, and so TRL is providing guidance by developing performance indices for different measures based on their effects on vehicle emissions. The emissions indices for passenger cars are based on tests conducted on a chassis dynamometer, and this paper describes the development of the methodology for constructing the driving cycles to be used. The technique involves the measurement of the speed profiles of a large number of vehicles using a roadside LIDAR system, and the determination of typical gear selections using three-instrumented cars

Commentary: Status of road safety in Asia.

Science.gov (United States)

Wismans, Jac; Skogsmo, Ingrid; Nilsson-Ehle, Anna; Lie, Anders; Thynell, Marie; Lindberg, Gunnar

2016-01-01

hand, lack of good high-quality accident data should not be an excuse to postpone interventions. There are many opportunities for evidence-based transport safety improvements, including measures concerning the 5 key risk factors: speed, drunk driving, not wearing motorcycle helmets, not wearing seat belts, and not using child restraints in cars, as specified in the Decade of Action for Road Safety 2011-2020. In this commentary, a number of additional measures are proposed that are not covered in the Decade of Action Plan. These new measures include separate roads or lanes for pedestrians and cyclists; helmet wearing for e-bike riders; special attention to elderly persons in public transportation; introduction of emerging collision avoidance technologies, in particular automatic emergency braking (AEB) and alcohol locks; improved truck safety focusing on the other road user (including blind spot detection technology; underride protection at the front, rear, and side; and energy-absorbing fronts); and improvements in motorcycle safety concerning protective clothing, requirements for advanced braking systems, improved visibility of motorcycles by using daytime running lights, and better guardrails.

Policy implementation lessons from six road pricing cases

NARCIS (Netherlands)

Vonk Noordegraaf, D.; Annema, J.A.; Wee, B. van

2014-01-01

The implementation of road pricing has been limited worldwide despite the notion that road pricing is generally considered to be a potentially effective measure to reduce externalities, in particular traffic congestion. By means of a content analysis of 106 scientific papers, this paper aims to

Investigation of road network features and safety performance.

Science.gov (United States)

Wang, Xuesong; Wu, Xingwei; Abdel-Aty, Mohamed; Tremont, Paul J

2013-07-01

The analysis of road network designs can provide useful information to transportation planners as they seek to improve the safety of road networks. The objectives of this study were to compare and define the effective road network indices and to analyze the relationship between road network structure and traffic safety at the level of the Traffic Analysis Zone (TAZ). One problem in comparing different road networks is establishing criteria that can be used to scale networks in terms of their structures. Based on data from Orange and Hillsborough Counties in Florida, road network structural properties within TAZs were scaled using 3 indices: Closeness Centrality, Betweenness Centrality, and Meshedness Coefficient. The Meshedness Coefficient performed best in capturing the structural features of the road network. Bayesian Conditional Autoregressive (CAR) models were developed to assess the safety of various network configurations as measured by total crashes, crashes on state roads, and crashes on local roads. The models' results showed that crash frequencies on local roads were closely related to factors within the TAZs (e.g., zonal network structure, TAZ population), while crash frequencies on state roads were closely related to the road and traffic features of state roads. For the safety effects of different networks, the Grid type was associated with the highest frequency of crashes, followed by the Mixed type, the Loops & Lollipops type, and the Sparse type. This study shows that it is possible to develop a quantitative scale for structural properties of a road network, and to use that scale to calculate the relationships between network structural properties and safety. Copyright © 2013 Elsevier Ltd. All rights reserved.

Tailpipe, resuspended road dust, and brake-wear emission factors from on-road vehicles

Science.gov (United States)

Abu-Allaban, Mahmoud; Gillies, John A.; Gertler, Alan W.; Clayton, Russ; Proffitt, David

Intensive mass and chemical measurements were performed at roadside locations in Reno, Nevada, and Durham/Research Triangle Park), North Carolina to derive tailpipe, resuspended road dust, and brake-wear emission factors from in-use vehicles. Continuous particulate matter (PM) data were utilized to derive total emission factors while integrated PM data were used to attribute the calculated emission factors to different mechanisms using chemical mass balance receptor modeling and scanning electron microscopy techniques. Resuspended road dust and tailpipe emissions were found to be the dominant mechanisms that contribute significantly to the total PM 10 and PM 2.5 emission factors, respectively. Small contributions from brake-wear were observed at locations where strong braking occurs, but no tire-wear was seen at any sampling location. PM 10 emission rates from light-duty spark ignition (LDSI) vehicles ranged from 40 to 780 mg/km, 10 to 70 mg/km, and 0 to 80 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 10 emission rates from heavy-duty vehicles ranged from 230 to 7800 mg/km, 60 to 570 mg/km, and 0 to 610 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 2.5 emission rates from LDSI vehicles ranged from 2 to 25 mg/km, 10 to 50 mg/km, and 0 to 5 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 2.5 emission rates from heavy-duty vehicles ranged from 15 to 300 mg/km, 60 to 480 mg/km, and 0 to 15 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively.

Road pricing and road safety : possible effects on road safety of 23 variants of road pricing.

NARCIS (Netherlands)

Eenink, R.G. Dijkstra, A. Wijnen, W. & Janssen, S.T.M.C.

2007-01-01

The Nouwen Committee (National Platform Paying Differently for Mobility) advised the Cabinet in 2005 about the introduction of a system of road pricing. Part of this advice consisted of a calculation of the expected road safety effects of such a system. In a letter to the Minister of Transport, SWOV

Sensitivity Analysis of Dune Height Measurements Along Cross-shore Profiles Using a Novel Method for Dune Ridge Extraction

Science.gov (United States)

Hardin, E.; Mitasova, H.; Overton, M.

2010-12-01

In barrier islands where communities are subjected to hazards including storm surge and high wave height, coastal dunes offer the first line of defense to property and vital infrastructure. When dunes are over-washed, substantial damage, including complete destruction of buildings and roads can occur. For this reason, dunes are an integral aspect of coastal hazard management. As new, more efficient mapping and analysis technologies evolve, currently used methodologies should be regularly be reexamined in order to ensure the development of the most effective coastal management strategies. Currently, topographical parameters, such as dune height, are usually measured along evenly spaced, shore-perpendicular beach profiles. In previous studies, profile spacing has varied from 20m to over 500m, however, it has been shown that dune height can vary substantially over tens of meters. Profile spacing is a compromise between the resources needed to perform high-resolution measurements and ensuring the capture of meaningful dune features. While it is often clear how the choice of profile spacing will affect the resources needed to perform the analysis, it is often unclear how spacing affects the ability to capture significant dune variation and prevent omission of a narrow dune breach that can open the way for significant flooding. In this study, the structure of alongshore variation in dune height is investigated. The studied dune ridge is located in the Outer Banks, North Carolina, USA and stretches 18km from south of Oregon Inlet (75:31:19W, 35:46:03N) to Rodanthe (75:27:56W, 35:36:31N). The dune ridge is extracted from a 0.5m resolution Digital Elevation Model (DEM) that was interpolated from airborne lidar data using regularized spline with tension. The lidar data was collected in March 2008 by the National Oceanic and Atmospheric Administration. A dune ridge is usually identified as the highest elevation along a shore-perpendicular profile or where ocean-facing slope

Road safety development in Europe: a decade of changes (2001-2010).

Science.gov (United States)

Shen, Yongjun; Hermans, Elke; Bao, Qiong; Brijs, Tom; Wets, Geert

2013-11-01

To evaluate the road safety development of a country over time, the percentage change in the number of road fatalities is traditionally the main indicator. However, simply considering the reduction in the road fatalities may not correctly reflect the real improvement in road safety because the transport circumstances of a country underlying the road fatalities also change every year. In this study, we present a new way for measuring the road safety performance change over time, which is to use the technique of data envelopment analysis (DEA) and the Malmquist productivity index. In doing so, we can not only focus on the evolution of road safety final outcomes within a given period, but also take the changes of different measures of exposure in the same period into account. In the application, the DEA-based Malmquist productivity index (DEA-MI) is used to measure the extent to which the EU countries have improved their road safety performance over the period 2001-2010. More objective and insightful results are obtained compared to the ones based on the traditional indicator. The results show considerable road safety progress in most of the Member States during these ten years, and the fatality risk rather than the fatality number on Europe's roads has actually been reduced by approximately half. However, the situation differed considerably from country to country. The decomposition of the DEA-MI into 'efficiency change' and 'technical change' further reveals that the bulk of the improvement during the last decade was attained through the adoption of productivity-enhancing new technologies throughout the road transport sector in Europe, rather than through the relatively underperforming countries catching up with those best-performing ones. Copyright © 2013 Elsevier Ltd. All rights reserved.

Concentration measurement in a road tunnel as a method to assess "real-world" vehicles exhaust emissions

Science.gov (United States)

Zanini, G.; Berico, M.; Monforti, F.; Vitali, L.; Zambonelli, S.; Chiavarini, S.; Georgiadis, T.; Nardino, M.

An experiment aimed at comparing particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs) concentrations produced in a road tunnel by buses is described. The experiment took place in 2001 in Bologna when a couple of buses belonging to the public transport fleet where driven backwards and forwards in a road tunnel closed to all other vehicles. Buses run in the tunnel for 8 h a day for 4 experiment days, each day using a different fuel: biodiesel, diesel-water emulsion, diesel-water emulsion with low sulphur content and commercial diesel. Average daily concentrations of PM of different sizes and of 12 PHAs were measured and comparison between different fuels was attempted in order to assess "real-world" exhaust emissions of different fuels. Due to heterogeneity of experimental conditions in different days and the relatively large measurement uncertainties, the effort was only partially successful, and it was not possible to state any firm conclusion on fuels reliability even if some indications in agreement with literature were found. Nevertheless, the experiment and the data analysis method developed could be of interest as a methodological approach for future experiments aimed at evaluating "real-world" exhaust emissions of single vehicles.

Road Transportation and Traffic Law Enforcement in Nigeria: A case ...

African Journals Online (AJOL)

Road Transportation and Traffic Law Enforcement in Nigeria was established in order to reduce the increasing road crashes and fatalities as well as making road users comply with traffic Laws and regulations as a counter measure, which remain as a great challenge in Nigeria. This paper discussed the roles of the Federal ...

The effect of vehicle characteristics on road accidents

CERN Document Server

Jones, I S

2016-01-01

The Effect of Vehicle Characteristics on Road Accidents investigates whether vehicle characteristics related to handling and stability contribute to road accidents. Using multiple regression analysis, this book addresses driver and vehicle effects separately in order to define both the magnitude of the handling/accident causation problem as well as the relative importance of the various performance measures. This monograph is comprised of six chapters and begins with detailed studies of accidents to determine the circumstances which lead to loss of control or overturning of a car on the road, and which accidents are likely to be influenced by the handling and stability characteristics of cars. Accident rates for these types of accident are then examined for the more popular models of car. Measures of vehicle handling and stability related to accident rates are also discussed. This text will be a useful resource for motorists and road engineers as well as transportation officials.

Road safety performance indicators for the interurban road network.

NARCIS (Netherlands)

Yannis, G. Weijermars, W.A.M. Gitelman, V. Vis, M. Chazirisa, A. Papadimitriou, E. & Lima Azevedo, C.

2013-01-01

Various road safety performance indicators (SPIs) have been proposed for different road safety research areas, mainly as regards driver behaviour (e.g. seat belt use, alcohol, drugs, etc.) and vehicles (e.g. passive safety); however, no SPIs for the road network and design have been developed. The

Evaluation of Multi-Year Continuous Measurements of Ultrafine Particles at Two Near-Road Stations in Toronto, Canada

Science.gov (United States)

Su, Y.; Sofowote, U.; Debosz, J.; Munoz, T.; Whitelaw, C.

2013-12-01

Particles with an aerodynamic diameter less than 100 nanometre (nm) are referred to as ultrafine particles (UFPs). Relative to fine and course particles, UFPs have greater potential to be suspended in air for a longer time and absorb toxic chemicals due to their larger surface areas per unit mass. UFPs could penetrate deep into the respiratory or cardiovascular systems and pose adverse health effects. In urban environments, primary sources of UFPs are from road traffic emissions and account for most of the total particle numbers. Controls on UPFs rely on better understanding of their emission sources and environmental behaviour. Ontario Ministry of the Environment have monitored UFPs since 2010 at two near-road stations in Toronto by using TSI 3031 UFP monitors. The two monitoring stations are approximately 20-30 meters adjacent to major arterial roads with over 20,000 vehicles per day. UFPs concentrations were monitored using six size channels: 20-30nm, 30-50nm, 50-70nm, 70-100nm, 100-200nm, and 200-450nm. Data are collected at time intervals of 11 or 15 minutes and averaged hourly. Concurrent measurements include wind speeds, wind directions, and concentrations of other air pollutants such as nitrogen oxides and black carbon. Data influenced by road-side traffic emissions were filtered by wind direction within 45° of normal to the road and wind speed greater than 1 m/s. Number concentrations were found higher for particles with sizes of 20-30nm and 30-50nm than for other sizes of UFPs. The observed particle number distributions are generally consistent with the theoretical understanding of particle nuclei mode and accumulation mode. During the day, for UFPs with sizes of 20-30nm and 30-50nm, elevated number concentrations were observed in morning traffic hours and to a less extent in the late afternoon. The elevated UFPs number concentrations coincided with nitrogen oxides and black carbon. Moreover, higher number concentrations were found on weekdays than

Full area covered 3D profile measurement of special-shaped optics based on a new prototype non-contact profiler.

Science.gov (United States)

Du, Hui-Lin; Zhou, Zhao-Zhong; Sun, Ze-Qing; Ju, Bing-Feng; Xu, Shaoning; Sun, Anyu

2017-06-01

A new prototype non-contact profiler based on surface tracking has been specially developed. Surface tracking is carried out by a specially designed dual stage probe system with the aid of a four-Degree Of Freedom high-precision motion platform. The dual stage probe system keeps a short-range optical probe constantly tracking the surface by a self-developed voice coil motor servo, by which a wide measuring range of up to 10 mm is realized. The system performance evaluation including resolution, repeatability, and scanning speed proved the good capability of the new prototype non-contact profiler. To realize a full area covered 3D profile measurement of special-shaped optics within one scanning procedure, a signal intensity monitor integrated in the surface tracking controller is specially developed. In the experiment, a snip-single-corner-rectangular-shaped freeform surface was successfully measured over full area by the new non-contact profiler. This work provides an effective solution for 3D profile measurement of special-shaped optical surfaces over full reflecting area. Experimental results demonstrate that the proposed measuring system is of great significance in quality evaluation of optical surfaces.

Scaling roads and wildlife: The Cinderella principle

Science.gov (United States)

Bissonette, J.A.

2002-01-01

It is clear that a reduction in both direct and indirect effects of roads and road networks must be the goal of management agencies. However, increased permeability of roaded landscapes can only be achieved by up-front planning and subsequent mitigative actions. The key is to understand that roads must be made permeable to the movement of animals. More profoundly, ecosystem services, i.e., clean water, clean air, uncontaminated soil, natural landscapes, recreation opportunities, abundant wildlife, and life sustaining ecological processes must not be seriously impacted. In other words, quality of life as measured by ecosystem services should be a major component of the planning process when roads are constructed or improved. Mitigative structures exist to increase permeability of roads. Wildlife overpasses and underpasses, often referred to as ecoducts or green bridges, with associated structures to enable larger animals to exit the road right of way, e.g., earthen escape ramps (BISSONETTE and HAMMER, 2001), various culvert designs for smaller animals including badger pipes and amphibian and reptile tunnels, and fish ladders are but a small sampling of the structures already in place around the world. What is needed is attention to the big picture. Landscapes need to be reconnected and made more permeable. Responsible agencies and organizations need to be aggressive about promoting mitigations and a conservation ethic into road planning. Only with a broad based effort between a concerned public, a database to work from, and a willingness of responsible agencies, will the now very large virtual footprint of roads and road networks be reduced to more closely approximate the physical footprint. By embracing the Cinderella Principle of making the virtual shoe fit more closely the actual physical footprint of roads, we will be able to achieve a closer connection with ecological harmony with its resultant effect of abundant wildlife.

Wire Scanner Beam Profile Measurements for the LANSCE Facility

International Nuclear Information System (INIS)

Gilpatrick, John D.; Gruchalla, Michael E.; Martinez, Derwin; Pillai, Chandra; Rodriguez Esparza, Sergio; Sedillo, James Daniel; Smith, Brian G.

2012-01-01

The Los Alamos Neutron Science Center (LANSCE) is replacing beam profile measurement systems, commonly known as Wire Scanners (WS). Using the principal of secondary electron emission, the WS measurement system moves a wire or fiber across an impinging particle beam, sampling a projected transverse-beam distribution. Because existing WS actuators and electronic components are either no longer manufactured or home-built with antiquated parts, a new WS beam profile measurement is being designed, fabricated, and tested. The goals for these new WS's include using off-the-shelf components while eliminating antiquated components, providing quick operation while allowing for easy maintainability, and tolerating external radioactivation. The WS measurement system consists of beam line actuators, a cable plant, an electronics processor chassis, and software located both in the electronics chassis (National Instruments LabVIEW) and in the Central Control Room (EPICS-based client software). This WS measurement system will measure Hand H + LANSCE-facility beams and will also measure less common beams. This paper describes these WS measurement systems.

Environmental exposure of road borders to zinc

International Nuclear Information System (INIS)

Blok, J.

2005-01-01

The emissions of zinc along roads originating from tyre wear, corrosion of safety fence and other traffic-related sources have been quantified and validated by measured long-term loads in road run-off and airborne solids (drift) for 29 published case studies. The distribution pattern over the road border at various distances from the edge of the paved surface is assessed on the basis of 38 published case studies with measured concentrations in soil. For the impact assessment, the road border is differentiated into a zone that is part of the 'technosphere' and the 'target zone' beyond that technosphere that can be considered as part of the receiving environment. The 'technosphere' of the road includes the central reservation, the hard and the soft shoulder or, if one or both shoulders are not present, the so-called obstacle 'free zone' that is defined by road engineers. Pollution within the technosphere may require appropriate management of solid disposal and isolation from groundwater to prevent further distribution of pollutants to the environment. In the target zone along regional roads, the zinc load is about 4 mg/m 2 year and this is of the same order of magnitude as that of atmospheric deposition in areas beyond the influence of roads (background). In the target zone along highways, the zinc load is increased in comparison to the background deposition. The average load of about 38 mg/m 2 year is similar to that in fertilised agricultural land. Because most of the emitted zinc stays in the technosphere, the total amount entering this target zone along highways is limited. From the 140 tons of zinc per year that is released from tyre wear in The Netherlands, 64 tons is emitted in the urban area, 6.5 tons reaches to the target zones of all roads and only 1.1 tons of zinc will enter the target zone along highways. This amount will be further decreased by the application of porous asphalt in the near future. The emission from safety fence corrosion does not enter

Reptile road-kills in Southern Brazil: Composition, hot moments and hotspots.

Science.gov (United States)

Gonçalves, Larissa Oliveira; Alvares, Diego Janisch; Teixeira, Fernanda Zimmermann; Schuck, Gabriela; Coelho, Igor Pfeifer; Esperandio, Isadora Beraldi; Anza, Juan; Beduschi, Júlia; Bastazini, Vinicius Augusto Galvão; Kindel, Andreas

2018-02-15

Understanding road-kill patterns is the first step to assess the potential effects of road mortality on wildlife populations, as well as to define the need for mitigation and support its planning. Reptiles are one of the vertebrate groups most affected by roads through vehicle collisions, both because they are intentionally killed by drivers, and due to their biological needs, such as thermoregulation, which make them more prone to collisions. We conducted monthly road surveys (33months), searching for carcasses of freshwater turtles, lizards, and snakes on a 277-km stretch of BR-101 road in Southernmost Brazil to estimate road-kill composition and magnitude and to describe the main periods and locations of road-kills. We modeled the distribution of road-kills in space according to land cover classes and local traffic volume. Considering the detection capacity of our method and carcass persistence probability, we estimated that 15,377 reptiles are road-killed per year (55reptiles/km/year). Road-kills, especially lizards and snakes, were concentrated during summer, probably due to their higher activity in this period. Road-kill hotspots were coincident among freshwater turtles, lizards, and snakes. Road-kill distribution was negatively related to pine plantations, and positively related to rice plantations and traffic volume. A cost-benefit analysis highlighted that if mitigation measures were installed at road-kill hotspots, which correspond to 21% of the road, they could have avoided up to 45% of recorded reptile fatalities, assuming a 100% mitigation effectiveness. Given the congruent patterns found for all three taxa, the same mitigation measures could be used to minimize the impacts of collision on local herpetofauna. Copyright © 2017 Elsevier B.V. All rights reserved.

Joint road safety operations in tunnels and open roads

Science.gov (United States)

Adesiyun, Adewole; Avenoso, Antonio; Dionelis, Kallistratos; Cela, Liljana; Nicodème, Christophe; Goger, Thierry; Polidori, Carlo

2017-09-01

The objective of the ECOROADS project is to overcome the barrier established by the formal interpretation of the two Directives 2008/96/EC and 2004/54/EC, which in practice do not allow the same Road Safety Audits/Inspections to be performed inside tunnels. The projects aims at the establishment of a common enhanced approach to road infrastructure and tunnel safety management by using the concepts and criteria of the Directive 2008/96/CE on road infrastructure safety management and the results of related European Commission (EC) funded projects. ECOROADS has already implemented an analysis of national practices regarding Road Safety Inspections (RSI), two Workshops with the stakeholders, and an exchange of best practices between European tunnel experts and road safety professionals, which led to the definition of common agreed safety procedures. In the second phase of the project, different groups of experts and observers applied the above common procedures by inspecting five European road sections featuring both open roads and tunnels in Belgium, Albania, Germany, Serbia and Former Yugoslav Republic of Macedonia. This paper shows the feedback of the 5 joint safety operations and how they are being used for a set of - recommendations and guidelines for the application of the RSA and RSI concepts within the tunnel safety operations.

Using Crumb Rubber from Waste Tires to Reduce Road Traffic Noise

Directory of Open Access Journals (Sweden)

Frolova Olga

2016-01-01

Full Text Available The results of measurements of sound pressure levels on an experimental road section (road pavement with addition of crumb rubber from waste tires in Mala Ida village (Kosice region, Slovakia and on a road with stone mastic asphalt in Haniska village (Presov region, Slovakia are presented in the paper. The results obtained using statistical pass-by methods were compared and they confirmed that road surface with addition of crumb rubber from waste tires produced quieter pavement than stone mastic asphalt road pavement alone.

Tire-road noise: an experimental study of tire and road design parameters

OpenAIRE

Bekke, Dirk; Wijnant, Ysbrand H.; Weegerink, Thijs; de Boer, Andries

2013-01-01

It is widely known that road traffic noise has negative influences on human health. Hence, as tire-road noise is considered to be the most dominant cause of road traffic noise above 30-50 km/h, a lot of research is performed by the two involving industries: road authorities/manufacturers and tire manufacturers. Usually, the parameters influencing exterior tire-road noise are often examined separately, whereas it is the tire-road interaction which obviously causes the actual noise. An integral...

The influence of road curvature on fatal crashes in New Zealand

DEFF Research Database (Denmark)

Haynes, Robin; Lake, Iain R.; Kingham, Simon

2008-01-01

Bends in roads can cause crashes but a recent study in the UK found that areas with mostly curved roads had lower crash rates than areas with straighter roads. This present study aimed to replicate the previous research in a different country. Variations in the number of fatal road crashes...... occurring between 1996 and 2005 in 73 territorial local authorities across New Zealand were modelled against possible predictors. The predictors were traffic flow, population counts and characteristics, car use, socio-economic deprivation, climate, altitude and road characteristics including four measures...... of average road curvature. The best predictors of the number of fatal crashes on urban roads, rural state highways and other rural roads were traffic flow, speed limitation and socio-economic deprivation. Holding significant factors constant, there was no evidence that TLAs with the most curved roads had...

Road Network Selection Based on Road Hierarchical Structure Control

Directory of Open Access Journals (Sweden)

HE Haiwei

2015-04-01

Full Text Available A new road network selection method based on hierarchical structure is studied. Firstly, road network is built as strokes which are then classified into hierarchical collections according to the criteria of betweenness centrality value (BC value. Secondly, the hierarchical structure of the strokes is enhanced using structural characteristic identification technique. Thirdly, the importance calculation model was established according to the relationships among the hierarchical structure of the strokes. Finally, the importance values of strokes are got supported with the model's hierarchical calculation, and with which the road network is selected. Tests are done to verify the advantage of this method by comparing it with other common stroke-oriented methods using three kinds of typical road network data. Comparision of the results show that this method had few need to semantic data, and could eliminate the negative influence of edge strokes caused by the criteria of BC value well. So, it is better to maintain the global hierarchical structure of road network, and suitable to meet with the selection of various kinds of road network at the same time.

Electron density profile measurements by microwave reflectometry on Tore Supra

International Nuclear Information System (INIS)

Clairet, F.; Paume, M.; Chareau, J.M.

1995-01-01

A proposal is presented developing reflectometry diagnostic for electron density profile measurements as routine diagnostic without manual intervention as achieved at JET. Since density fluctuations seriously perturb the reflected signal and the measurement of the group delay, a method is described to overcome the irrelevant results with the help of an adaptive filtering technique. Accurate profiles are estimated for about 70% of the shots. (author) 3 refs.; 6 figs

[Road safety measures and their effects on traffic injuries: a systematic review].

Science.gov (United States)

Aguilera, Sandra Lúcia Vieira Ulinski; Moysés, Simone Tetú; Moysés, Samuel Jorge

2014-10-01

To identify and summarize the findings of studies describing interventions aimed at reducing road traffic injuries. An integrative systematic review without meta-analysis was performed. The Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) were used to synthesize the findings of the articles reviewed. The keywords "traffic accidents", "review" and "public policy" were used in isolation or combined with boolean operator "And" to search PubMed, Web of Science, SciELO, and LILACS for the period between 2006 and 2011 RESULTS: Twenty-two studies were included in the systematic review. Of these, two described engineering strategies, two described other road safety policies, three described education strategies, and 15 described law enforcement policies. Law enforcement had the most effective immediate results. Engineering strategies proved important to promote a safe environment. Finally, education strategies had an informative role and served to support other strategies, but did not seem sufficient to promote cultural changes regarding road safety. Law enforcement seems to be the most effective strategy to change the behavior of drivers, especially regarding speed limits and drinking and driving.

Wheel-Based Ice Sensors for Road Vehicles

Science.gov (United States)

Arndt, G. Dickey; Fink, Patrick W.; Ngo, Phong H.; Carl, James R.

2011-01-01

Wheel-based sensors for detection of ice on roads and approximate measurement of the thickness of the ice are under development. These sensors could be used to alert drivers to hazardous local icing conditions in real time. In addition, local ice-thickness measurements by these sensors could serve as guidance for the minimum amount of sand and salt required to be dispensed locally onto road surfaces to ensure safety, thereby helping road crews to utilize their total supplies of sand and salt more efficiently. Like some aircraft wing-surface ice sensors described in a number of previous NASA Tech Briefs articles, the wheelbased ice sensors are based, variously, on measurements of changes in capacitance and/or in radio-frequency impedance as affected by ice on surfaces. In the case of ice on road surfaces, the measurable changes in capacitance and/or impedance are attributable to differences among the electric permittivities of air, ice, water, concrete, and soil. In addition, a related phenomenon that can be useful for distinguishing between ice and water is a specific transition in the permittivity of ice at a temperature- dependent frequency. This feature also provides a continuous calibration of the sensor to allow for changing road conditions. Several configurations of wheel-based ice sensors are under consideration. For example, in a simple two-electrode capacitor configuration, one of the electrodes would be a circumferential electrode within a tire, and the ground would be used as the second electrode. Optionally, the steel belts that are already standard parts of many tires could be used as the circumferential electrodes. In another example (see figure), multiple electrodes would be embedded in rubber between the steel belt and the outer tire surface. These electrodes would be excited in alternating polarities at one or more suitable audio or radio frequencies to provide nearly continuous monitoring of the road surface under the tire. In still another

Neutral Probe Beam q-profile measurements in PDX and PBX-M

International Nuclear Information System (INIS)

Kugel, H.W.; Gammel, G.M.; Kaita, R.; Reusch, M.F.; Roberts, D.W.

1988-06-01

Using the Fast Ion Diagnostic Experiment (FIDE) technique, a Neutral Probe Beam (NPB) can be aimed to inject tangentially to a magnetic surface. The resultant ion orbit shifts, due to conservation of canonical toroidal angular momentum, can be measured with a multi-sightline charge-exchange analyzer to yield direct measurements of radial magnetic flux profiles, current density profiles, the radial position of the magnetic axis, flux surface inner and outer edges, q-profiles, and central-q time dependencies. An extensive error analysis was performed on previous PDX q-measurements in circular plasmas and the resulting estimated contributions of various systematic effects are discussed. Preliminary results of fast ion orbit shift measurements at early times in indented PBX-M plasmas are given. Methods for increasing the absolute experimental precision of similar measurements in progress on PBX-M are discussed. 4 refs., 3 figs

A novel non-contact profiler design for measuring synchrotron radiation mirrors

International Nuclear Information System (INIS)

Lin, Yao; Takacs, P.Z.; Furenlid, K.; DeBiasse, R.A.; Wang, Run-Wen

1990-08-01

A novel optical profiler is described in this paper for measurement of surface profiles of synchrotron radiation (SR) mirrors. The measurement is based on a combination of an optical heterodyne technique and a precise phase measurement procedure without a reference surface. A Zeeman two-frequency He-Ne laser is employed as the light source. The common-path optical system, which uses a birefringent lens as the beam splitter, minimizes the effects of air turbulence, sample vibration and temperature variation. A special autofocus system allows the profiler to measure the roughness and shape of a sample surface. The optical system is mounted on a large linear air-bearing slide, and is capable of scanning over distances covering the spatial period range from several microns to nearly one meter with a high measurement accuracy. 9 refs., 5 figs

Binary similarity measures for fingerprint analysis of qualitative metabolomic profiles.

Science.gov (United States)

Rácz, Anita; Andrić, Filip; Bajusz, Dávid; Héberger, Károly

2018-01-01

Contemporary metabolomic fingerprinting is based on multiple spectrometric and chromatographic signals, used either alone or combined with structural and chemical information of metabolic markers at the qualitative and semiquantitative level. However, signal shifting, convolution, and matrix effects may compromise metabolomic patterns. Recent increase in the use of qualitative metabolomic data, described by the presence (1) or absence (0) of particular metabolites, demonstrates great potential in the field of metabolomic profiling and fingerprint analysis. The aim of this study is a comprehensive evaluation of binary similarity measures for the elucidation of patterns among samples of different botanical origin and various metabolomic profiles. Nine qualitative metabolomic data sets covering a wide range of natural products and metabolomic profiles were applied to assess 44 binary similarity measures for the fingerprinting of plant extracts and natural products. The measures were analyzed by the novel sum of ranking differences method (SRD), searching for the most promising candidates. Baroni-Urbani-Buser (BUB) and Hawkins-Dotson (HD) similarity coefficients were selected as the best measures by SRD and analysis of variance (ANOVA), while Dice (Di1), Yule, Russel-Rao, and Consonni-Todeschini 3 ranked the worst. ANOVA revealed that concordantly and intermediately symmetric similarity coefficients are better candidates for metabolomic fingerprinting than the asymmetric and correlation based ones. The fingerprint analysis based on the BUB and HD coefficients and qualitative metabolomic data performed equally well as the quantitative metabolomic profile analysis. Fingerprint analysis based on the qualitative metabolomic profiles and binary similarity measures proved to be a reliable way in finding the same/similar patterns in metabolomic data as that extracted from quantitative data.

eRoads

DEFF Research Database (Denmark)

Connolly, David

vehicles enable more renewable electricity to be integrated onto the electricity grid. This is particularly evident in 2050, since the price of fossil fuels increases while the price of renewable electricity and batteries decreases. Finally, the electric road scenarios can facilitate more reductions......This study compares electric roads with oil (petrol and diesel) and battery electric vehicles, using Denmark as a case study. Electric roads can reduce the cost of electric vehicles by supplying them with electricity directly from the road rather than via a battery for long-distance journeys....... In this paper, an electric road scenario is compared to both an oil and battery electric vehicle scenario using the 2010 Danish energy system, but for two sets of costs: one set based on historical costs from the year 2010 and one based on projected costs for the year 2050. The results indicate that electric...

Gamma-ray emission profile measurements during JET ICRH discharges

Energy Technology Data Exchange (ETDEWEB)

Jarvis, O N; Marcus, F B; Sadler, G; Van Belle, P [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Howarth, P J.A. [Birmingham Univ. (United Kingdom); Adams, J M; Bond, D S [UKAEA Harwell Lab. (United Kingdom). Energy Technology Div.

1994-07-01

Gamma-ray emission from plasma-impurity reactions caused by minority ICRH accelerating fuel ions to MeV energies has been measured using the JET neutron profile monitor. A successful data analysis technique has been used to isolate the RF-induced gamma-ray emission that was detected, enabling profiles of gamma-ray emission to be obtained. The 2-d gamma-ray emission profiles show that virtually all the radiation originates from the low field side of the RF resonance layer, as expected from RF-induced pitch angle diffusion. The emission profiles indicate the presence of a small population of resonant {sup 3}He ions that possess orbits lying near the passing-trapped boundary. 6 refs., 4 figs.

Illumination Profile & Dispersion Variation Effects on Radial Velocity Measurements

Science.gov (United States)

Grieves, Nolan; Ge, Jian; Thomas, Neil B.; Ma, Bo; Li, Rui; SDSS-III

2015-01-01

The Multi-object APO Radial-Velocity Exoplanet Large-Area Survey (MARVELS) measures radial velocities using a fiber-fed dispersed fixed-delay interferometer (DFDI) with a moderate dispersion spectrograph. This setup allows a unique insight into the 2D illumination profile from the fiber on to the dispersion grating. Illumination profile investigations show large changes in the profile over time and fiber location. These profile changes are correlated with dispersion changes and long-term radial velocity offsets, a major problem within the MARVELS radial velocity data. Characterizing illumination profiles creates a method to both detect and correct radial velocity offsets, allowing for better planet detection. Here we report our early results from this study including improvement of radial velocity data points from detected giant planet candidates. We also report an illumination profile experiment conducted at the Kitt Peak National Observatory using the EXPERT instrument, which has a DFDI mode similar to MARVELS. Using profile controlling octagonal-shaped fibers, long term offsets over a 3 month time period were reduced from ~50 m/s to within the photon limit of ~4 m/s.

Measuring the Impact of Road Rehabilitation on Spatial Market Efficiency in Maize Markets in Mozambique

DEFF Research Database (Denmark)

Cirera, Xavier; Arndt, Channing

2008-01-01

to the existing literature in three ways. First, a unique data set, where road rehabilitation episodes between market pairs are identified, is developed. Second, special care is devoted to estimation of transaction costs due to the sensitivity of the PBM model to the quality of transaction costs estimates......This article analyzes the impact of road rehabilitation on the spatial market efficiency of maize markets in Mozambique. We estimate a modified version of the Parity Bounds Model (PBM) that allows us to test the impact of road rehabilitation on spatial efficiency. This article seeks to contribute....... Finally, as opposed to most existing literature that focuses on relatively distant markets, the article focuses on spatially closed markets. We find that maize markets tend to be segmented due to high transport costs. Following road rehabilitation, inefficiency and average absolute price differentials...

High resolution measurements and modeling of auroral hydrogen emission line profiles

Directory of Open Access Journals (Sweden)

B. S. Lanchester

Full Text Available Measurements in the visible wavelength range at high spectral resolution (1.3 Å have been made at Longyearbyen, Svalbard (15.8 E,78.2 N during an interval of intense proton precipitation. The shape and Doppler shift of hydrogen Balmer beta line profiles have been compared with model line profiles, using as input ion energy spectra from almost coincident passes of the FAST and DMSP spacecraft. The comparison shows that the simulation contains the important physical processes that produce the profiles, and confirms that measured changes in the shape and peak wave-length of the hydrogen profiles are the result of changing energy input. This combination of high resolution measurements with modeling provides a method of estimating the incoming energy and changes in flux of precipitating protons over Svalbard, for given energy and pitch-angle distributions. Whereas for electron precipitation, information on the incident particles is derived from brightness and brightness ratios which require at least two spectral windows, for proton precipitation the Doppler profile of resulting hydrogen emission is directly related to the energy and energy flux of the incident energetic protons and can be used to gather information about the source region. As well as the expected Doppler shift to shorter wavelengths, the measured profiles have a significant red-shifted component, the result of upward flowing emitting hydrogen atoms.

Key words. Ionosphere (auroral ionosphere; particle precipitation – Magnetospheric physics (auroral phenomena

High resolution measurements and modeling of auroral hydrogen emission line profiles

Directory of Open Access Journals (Sweden)

B. S. Lanchester

2003-07-01

Full Text Available Measurements in the visible wavelength range at high spectral resolution (1.3 Å have been made at Longyearbyen, Svalbard (15.8 E,78.2 N during an interval of intense proton precipitation. The shape and Doppler shift of hydrogen Balmer beta line profiles have been compared with model line profiles, using as input ion energy spectra from almost coincident passes of the FAST and DMSP spacecraft. The comparison shows that the simulation contains the important physical processes that produce the profiles, and confirms that measured changes in the shape and peak wave-length of the hydrogen profiles are the result of changing energy input. This combination of high resolution measurements with modeling provides a method of estimating the incoming energy and changes in flux of precipitating protons over Svalbard, for given energy and pitch-angle distributions. Whereas for electron precipitation, information on the incident particles is derived from brightness and brightness ratios which require at least two spectral windows, for proton precipitation the Doppler profile of resulting hydrogen emission is directly related to the energy and energy flux of the incident energetic protons and can be used to gather information about the source region. As well as the expected Doppler shift to shorter wavelengths, the measured profiles have a significant red-shifted component, the result of upward flowing emitting hydrogen atoms.Key words. Ionosphere (auroral ionosphere; particle precipitation – Magnetospheric physics (auroral phenomena

A Public Health Perspective of Road Traffic Accidents

Science.gov (United States)

Gopalakrishnan, S.

2012-01-01

Road traffic accidents (RTAs) have emerged as an important public health issue which needs to be tackled by a multi-disciplinary approach. The trend in RTA injuries and death is becoming alarming in countries like India. The number of fatal and disabling road accident happening is increasing day by day and is a real public health challenge for all the concerned agencies to prevent it. The approach to implement the rules and regulations available to prevent road accidents is often ineffective and half-hearted. Awareness creation, strict implementation of traffic rules, and scientific engineering measures are the need of the hour to prevent this public health catastrophe. This article is intended to create awareness among the health professionals about the various modalities available to prevent road accidents and also to inculcate a sense of responsibility toward spreading the message of road safety as a good citizen of our country. PMID:24479025

Wire Scanner Beam Profile Measurements for the LANSCE Facility

Energy Technology Data Exchange (ETDEWEB)

Gilpatrick, John D. [Los Alamos National Laboratory; Gruchalla, Michael E. [Los Alamos National Laboratory; Martinez, Derwin [Los Alamos National Laboratory; Pillai, Chandra [Los Alamos National Laboratory; Rodriguez Esparza, Sergio [Los Alamos National Laboratory; Sedillo, James Daniel [Los Alamos National Laboratory; Smith, Brian G. [Los Alamos National Laboratory

2012-05-15

The Los Alamos Neutron Science Center (LANSCE) is replacing beam profile measurement systems, commonly known as Wire Scanners (WS). Using the principal of secondary electron emission, the WS measurement system moves a wire or fiber across an impinging particle beam, sampling a projected transverse-beam distribution. Because existing WS actuators and electronic components are either no longer manufactured or home-built with antiquated parts, a new WS beam profile measurement is being designed, fabricated, and tested. The goals for these new WS's include using off-the-shelf components while eliminating antiquated components, providing quick operation while allowing for easy maintainability, and tolerating external radioactivation. The WS measurement system consists of beam line actuators, a cable plant, an electronics processor chassis, and software located both in the electronics chassis (National Instruments LabVIEW) and in the Central Control Room (EPICS-based client software). This WS measurement system will measure Hand H{sup +} LANSCE-facility beams and will also measure less common beams. This paper describes these WS measurement systems.

Temperature profiles by ground-based remote sensing and in situ measurements

Energy Technology Data Exchange (ETDEWEB)

Argentini, S; Pietroni, I; Conidi, A; Mastrantonio, G; Petenko, I; Viola, A [ISAC-CNR, Via del Fosso del Cavaliere, 100, 00133 Roma (Italy); Gariazzo, C; Pelliccioni, A; Amicarelli, A [ISPESL Dipartimento Insediamenti Produttivi e Interazione con l' Ambiente, Via Fontana Candida, 1, 00040 Monteporzio Catone (RM) (Italy)], E-mail: s.argentini@isac.cnr.it

2008-05-01

This study focuses on the accuracy of the temperature profiles measured with a Doppler Radio-Acoustic Sounding System and a Microwave Temperature Profiler during a period of about 3 months in winter 2007-2008. The experiment was carried on at the experimental facility of the Institute of Atmospheric Sciences and Climate (ISAC) of the Italian National Research Council (CNR). The temperature data measured with remote sensors were verified with in situ measurements on a mast as well as with tethered balloon data. The facsimile echograms obtained with the ISAC Doppler SODAR were analysed to understand to which extent the RASS and Radiometer temperature profiles behaviour can represent the real thermal structure of the atmosphere.

Temperature profiles by ground-based remote sensing and in situ measurements

International Nuclear Information System (INIS)

Argentini, S; Pietroni, I; Conidi, A; Mastrantonio, G; Petenko, I; Viola, A; Gariazzo, C; Pelliccioni, A; Amicarelli, A

2008-01-01

This study focuses on the accuracy of the temperature profiles measured with a Doppler Radio-Acoustic Sounding System and a Microwave Temperature Profiler during a period of about 3 months in winter 2007-2008. The experiment was carried on at the experimental facility of the Institute of Atmospheric Sciences and Climate (ISAC) of the Italian National Research Council (CNR). The temperature data measured with remote sensors were verified with in situ measurements on a mast as well as with tethered balloon data. The facsimile echograms obtained with the ISAC Doppler SODAR were analysed to understand to which extent the RASS and Radiometer temperature profiles behaviour can represent the real thermal structure of the atmosphere

Climate Projection Data base for Roads - CliPDaR: Design a guideline for a transnational database of downscaled climate projection data for road impact models - within the Conference's of European Directors of Roads (CEDR) TRANSNATIONAL ROAD RESEARCH PROG

Science.gov (United States)

Matulla, Christoph; Namyslo, Joachim; Fuchs, Tobias; Türk, Konrad

2013-04-01

The European road sector is vulnerable to extreme weather phenomena, which can cause large socio-economic losses. Almost every year there occur several weather triggered events (like heavy precipitation, floods, landslides, high winds, snow and ice, heat or cold waves, etc.), that disrupt transportation, knock out power lines, cut off populated regions from the outside and so on. So, in order to avoid imbalances in the supply of vital goods to people as well as to prevent negative impacts on health and life of people travelling by car it is essential to know present and future threats to roads. Climate change might increase future threats to roads. CliPDaR focuses on parts of the European road network and contributes, based on the current body of knowledge, to the establishment of guidelines helping to decide which methods and scenarios to apply for the estimation of future climate change based challenges in the field of road maintenance. Based on regional scale climate change projections specific road-impact models are applied in order to support protection measures. In recent years, it has been recognised that it is essential to assess the uncertainty and reliability of given climate projections by using ensemble approaches and downscaling methods. A huge amount of scientific work has been done to evaluate these approaches with regard to reliability and usefulness for investigations on possible impacts of climate changes. CliPDaR is going to collect the existing approaches and methodologies in European countries, discuss their differences and - in close cooperation with the road owners - develops a common line on future applications of climate projection data to road impact models. As such, the project will focus on reviewing and assessing existing regional climate change projections regarding transnational highway transport needs. The final project report will include recommendations how the findings of CliPDaR may support the decision processes of European

All-terrain vehicle fatalities on paved roads, unpaved roads, and off-road: Evidence for informed roadway safety warnings and legislation.

Science.gov (United States)

Denning, Gerene M; Jennissen, Charles A

2016-05-18

All-terrain vehicles (ATVs) are designed for off-highway use only, and many of their features create increased risk with roadway travel. Over half of all ATV-related fatalities occur on roadways, and nonfatal roadway crashes result in more serious injuries than those off the road. A number of jurisdictions have passed or have considered legislation allowing ATVs on public roadways, sometimes limiting them to those unpaved, arguing that they are safe for ATVs. However, no studies have determined the epidemiology of ATV-related fatalities on different road surface types. The objective of the study was to compare ATV-related deaths on paved versus unpaved roads and to contrast them with off-road fatalities. Retrospective descriptive and multivariable analyses were performed using U.S. Consumer Product Safety Commission fatality data from 1982 through 2012. After 1998, ATV-related deaths increased at twice the rate on paved versus unpaved roads. Still, 42% of all roadway deaths during the study period occurred on unpaved surfaces. States varied considerably, ranging from 18% to 79% of their ATV-related roadway deaths occurring on unpaved roads. Paved road crashes were more likely than those on unpaved surfaces to involve males, adolescents and younger adults, passengers, and collisions with other vehicles. Both the pattern of other vehicles involved in collisions and which vehicle hit the other were different for the 2 road types. Alcohol use was higher, helmet use was lower, and head injuries were more likely in paved versus unpaved roadway crashes. However, head injuries still occurred in 76% of fatalities on unpaved roads. Helmets were associated with lower proportions of head injuries among riders, regardless of road surface type. Relative to off-road crashes, both paved and unpaved roads were more likely to involve collisions with another vehicle. The vast majority of roadway crashes, however, did not involve a traffic collision on either paved or unpaved roads

40 CFR 86.129-94 - Road load power, test weight, inertia weight class determination, and fuel temperature profile.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Road load power, test weight, inertia... Procedures § 86.129-94 Road load power, test weight, inertia weight class determination, and fuel temperature... duty trucks 1,2,3 Test weightbasis 4,5 Test equivalent test weight(pounds) Inertia weight class(pounds...

Using endemic road features to create self-explaining roads and reduce vehicle speeds.

Science.gov (United States)

Charlton, Samuel G; Mackie, Hamish W; Baas, Peter H; Hay, Karen; Menezes, Miguel; Dixon, Claire

2010-11-01

This paper describes a project undertaken to establish a self-explaining roads (SER) design programme on existing streets in an urban area. The methodology focussed on developing a process to identify functional road categories and designs based on endemic road characteristics taken from functional exemplars in the study area. The study area was divided into two sections, one to receive SER treatments designed to maximise visual differences between road categories, and a matched control area to remain untreated for purposes of comparison. The SER design for local roads included increased landscaping and community islands to limit forward visibility, and removal of road markings to create a visually distinct road environment. In comparison, roads categorised as collectors received increased delineation, addition of cycle lanes, and improved amenity for pedestrians. Speed data collected 3 months after implementation showed a significant reduction in vehicle speeds on local roads and increased homogeneity of speeds on both local and collector roads. The objective speed data, combined with residents' speed choice ratings, indicated that the project was successful in creating two discriminably different road categories. 2010 Elsevier Ltd. All rights reserved.

Measuring of Traction and Speed Characteristics as Well as of Fuel Economy of a Car in Road Conditions

OpenAIRE

Krivtsov, Sergey; Syrbakov, Andrey Pavlovich; Korchuganova, Mariya Anatolievna

2016-01-01

This article is devoted to the identification of traction and speed characteristics as well as of fuel economy of motor vehicles in road conditions. Among common variants of measuring of the above stated values, the preference was given to the immediate gaining of factors by means of a computer-aided measuring system. There is a theoretical justification given to the suggested approach as well as methods and results allowing to provide a practically sufficient solution accuracy of the problem.

Measuring of Traction and Speed Characteristics as Well as of Fuel Economy of a Car in Road Conditions

Science.gov (United States)

Krivtsov, Sergey N.; Syrbakov, Andrey P.; Korchuganova, Marina A.

2016-08-01

This article is devoted to the identification of traction and speed characteristics as well as of fuel economy of motor vehicles in road conditions. Among common variants of measuring of the above stated values, the preference was given to the immediate gaining of factors by means of a computer-aided measuring system. There is a theoretical justification given to the suggested approach as well as methods and results allowing to provide a practically sufficient solution accuracy of the problem.

Mammal and bird road mortalities on the Upington to Twee Rivieren ...

African Journals Online (AJOL)

A mammal hotspot was identified along the 91 km of road that traversed the Gordonia duneveld. Since the nine roadside traffic warning signs erected on the R360 road had no measurable impact on road mortalities, it is recommend that three rumble strip sections with accompanying signage be erected in the hotspot to ...

Roads at risk - the impact of debris flows on road network reliability and vulnerability in southern Norway

Science.gov (United States)

Meyer, Nele Kristin; Schwanghart, Wolfgang; Korup, Oliver

2014-05-01

Norwegian's road network is frequently affected by debris flows. Both damage repair and traffic interruption generate high economic losses and necessitate a rigorous assessment of where losses are expected to be high and where preventive measures should be focused on. In recent studies, we have developed susceptibility and trigger probability maps that serve as input into a hazard calculation at the scale of first-order watersheds. Here we combine these results with graph theory to assess the impact of debris flows on the road network of southern Norway. Susceptibility and trigger probability are aggregated for individual road sections to form a reliability index that relates to the failure probability of a link that connects two network vertices, e.g., road junctions. We define link vulnerability as a function of traffic volume and additional link failure distance. Additional link failure distance is the extra length of the alternative path connecting the two associated link vertices in case the network link fails and is calculated by a shortest-path algorithm. The product of network reliability and vulnerability indices represent the risk index. High risk indices identify critical links for the Norwegian road network and are investigated in more detail. Scenarios demonstrating the impact of single or multiple debris flow events are run for the most important routes between seven large cities in southern Norway. First results show that the reliability of the road network is lowest in the central and north-western part of the study area. Road network vulnerability is highest in the mountainous regions in central southern Norway where the road density is low and in the vicinity of cities where the traffic volume is large. The scenarios indicate that city connections that have their shortest path via routes crossing the central part of the study area have the highest risk of route failure.

Road safety performance indicators for the interurban road network.

Science.gov (United States)

Yannis, George; Weijermars, Wendy; Gitelman, Victoria; Vis, Martijn; Chaziris, Antonis; Papadimitriou, Eleonora; Azevedo, Carlos Lima

2013-11-01

Various road safety performance indicators (SPIs) have been proposed for different road safety research areas, mainly as regards driver behaviour (e.g. seat belt use, alcohol, drugs, etc.) and vehicles (e.g. passive safety); however, no SPIs for the road network and design have been developed. The objective of this research is the development of an SPI for the road network, to be used as a benchmark for cross-region comparisons. The developed SPI essentially makes a comparison of the existing road network to the theoretically required one, defined as one which meets some minimum requirements with respect to road safety. This paper presents a theoretical concept for the determination of this SPI as well as a translation of this theory into a practical method. Also, the method is applied in a number of pilot countries namely the Netherlands, Portugal, Greece and Israel. The results show that the SPI could be efficiently calculated in all countries, despite some differences in the data sources. In general, the calculated overall SPI scores were realistic and ranged from 81 to 94%, with the exception of Greece where the SPI was relatively lower (67%). However, the SPI should be considered as a first attempt to determine the safety level of the road network. The proposed method has some limitations and could be further improved. The paper presents directions for further research to further develop the SPI. Copyright © 2012 Elsevier Ltd. All rights reserved.

ROAD TRANSPORT ACCIDENTS IN NIGERIA AND THE ROLE

Directory of Open Access Journals (Sweden)

Olasunkanmi Oriola AKINYEMI

2016-06-01

Full Text Available Analysis of road traffic accidents revealed that most accidents are as a result of drivers’ errors. Over the years, active safety systems (ASS were devised in vehicle to reduce the high level of road accidents, caused by human errors, leading to death and injuries.This study however evaluated the impacts of ASS inclusions into vehicles in Nigeria road transportation network. The objectives was to measure how ASS contributed to making driving safer and enhanced transport safety. Road accident data were collected, for a period of eleven years, from Lagos State Ministry of Economic Planning and Budget, Central Office of Statistics. Quantitative analysis of the retrospective accident was conducted by computing the proportion of yearly number of vehicles involved in road accident to the total number of vehicles for each year. Results of the analysis showed that the proportion of vehicles involved in road accidents decreased from 16 in 1996 to 0.89 in 2006, the injured persons reduced from 15.58 in 1998 to 0.3 in 2006 and the death rate diminished from 4.45 in 1998 to 0.1 in 2006. These represented 94.4%, 95% and 95% improvement respectively on road traffic safety. It can therefore be concluded that the inclusions of ASS into design of modern vehicles had improved road safety in Nigeria automotive industry.

[Evidence-based effectiveness of road safety interventions: a literature review].

Science.gov (United States)

Novoa, Ana M; Pérez, Katherine; Borrell, Carme

2009-01-01

Only road safety interventions with scientific evidence supporting their effectiveness should be implemented. The objective of this study was to identify and summarize the available evidence on the effectiveness of road safety interventions in reducing road traffic collisions, injuries and deaths. All literature reviews published in scientific journals that assessed the effectiveness of one or more road safety interventions and whose outcome measure was road traffic crashes, injuries or fatalities were included. An exhaustive search was performed in scientific literature databases. The interventions were classified according to the evidence of their effectiveness in reducing road traffic injuries (effective interventions, insufficient evidence of effectiveness, ineffective interventions) following the structure of the Haddon matrix. Fifty-four reviews were included. Effective interventions were found before, during and after the collision, and across all factors: a) the individual: the graduated licensing system (31% road traffic injury reduction); b) the vehicle: electronic stability control system (2 to 41% reduction); c) the infrastructure: area-wide traffic calming (0 to 20%), and d) the social environment: speed cameras (7 to 30%). Certain road safety interventions are ineffective, mostly road safety education, and others require further investigation. The most successful interventions are those that reduce or eliminate the hazard and do not depend on changes in road users' behavior or on their knowledge of road safety issues. Interventions based exclusively on education are ineffective in reducing road traffic injuries.

Environmental exposure of road borders to zinc

Energy Technology Data Exchange (ETDEWEB)

Blok, J. [Royal Haskoning, P.O. Box 151, 6500 Ad Nijmegen (Netherlands)]. E-mail: Han.Blok@royalhaskoning.com

2005-09-15

The emissions of zinc along roads originating from tyre wear, corrosion of safety fence and other traffic-related sources have been quantified and validated by measured long-term loads in road run-off and airborne solids (drift) for 29 published case studies. The distribution pattern over the road border at various distances from the edge of the paved surface is assessed on the basis of 38 published case studies with measured concentrations in soil. For the impact assessment, the road border is differentiated into a zone that is part of the 'technosphere' and the 'target zone' beyond that technosphere that can be considered as part of the receiving environment. The 'technosphere' of the road includes the central reservation, the hard and the soft shoulder or, if one or both shoulders are not present, the so-called obstacle 'free zone' that is defined by road engineers. Pollution within the technosphere may require appropriate management of solid disposal and isolation from groundwater to prevent further distribution of pollutants to the environment. In the target zone along regional roads, the zinc load is about 4 mg/m{sup 2} year and this is of the same order of magnitude as that of atmospheric deposition in areas beyond the influence of roads (background). In the target zone along highways, the zinc load is increased in comparison to the background deposition. The average load of about 38 mg/m{sup 2} year is similar to that in fertilised agricultural land. Because most of the emitted zinc stays in the technosphere, the total amount entering this target zone along highways is limited. From the 140 tons of zinc per year that is released from tyre wear in The Netherlands, 64 tons is emitted in the urban area, 6.5 tons reaches to the target zones of all roads and only 1.1 tons of zinc will enter the target zone along highways. This amount will be further decreased by the application of porous asphalt in the near future. The

Testing road surface treatments to reduce erosion in forest roads in Honduras [Tratamientos de la superficie de rodadura para reducir la erosion en caminos forestales en Honduras

Science.gov (United States)

Rivera, Samuel; Kershner, Jeffrey L.; Keller, Gordon R.

2009-01-01

Testing road surface treatments to reduce erosion in forest roads in Honduras. Cien. Inv. Agr. 36(3):425-432. Using forest roads produces more erosion and sedimentation than any other forest or agricultural activity. This study evaluated soil losses from a forest road in central Honduras over two consecutive years. We divided a 400-m segment of road into 8 experimental units, each 50 m in length. Four units were treated with Best Management Practices (BMPs) and four were left untreated. The BMP treatments included reshaping the road prism, installing culverts and reshaping of road ditches, compacting 20-cm layers of the road tread, crowning the road surface (3% slope, double drainage), longitudinal sloping (less than 12%), and adding a 10-cm layer of gravel (crush size = 0.63 cm). Soil movement was measured daily during the rainy seasons. The highest soil loss occurred in the control road, around 500 m3 km-1 per year, while the road treated with BMP lost approximately 225 m3km-1 per year. These results show that road surface erosion can be reduced up to 50% with the implementation of surface treatments.

Road density

Data.gov (United States)

U.S. Environmental Protection Agency — Road density is generally highly correlated with amount of developed land cover. High road densities usually indicate high levels of ecological disturbance. More...

A measurement system for vertical seawater profiles close to the air-sea interface

Science.gov (United States)

Sims, Richard P.; Schuster, Ute; Watson, Andrew J.; Yang, Ming Xi; Hopkins, Frances E.; Stephens, John; Bell, Thomas G.

2017-09-01

This paper describes a near-surface ocean profiler, which has been designed to precisely measure vertical gradients in the top 10 m of the ocean. Variations in the depth of seawater collection are minimized when using the profiler compared to conventional CTD/rosette deployments. The profiler consists of a remotely operated winch mounted on a tethered yet free-floating buoy, which is used to raise and lower a small frame housing sensors and inlet tubing. Seawater at the inlet depth is pumped back to the ship for analysis. The profiler can be used to make continuous vertical profiles or to target a series of discrete depths. The profiler has been successfully deployed during wind speeds up to 10 m s-1 and significant wave heights up to 2 m. We demonstrate the potential of the profiler by presenting measured vertical profiles of the trace gases carbon dioxide and dimethylsulfide. Trace gas measurements use an efficient microporous membrane equilibrator to minimize the system response time. The example profiles show vertical gradients in the upper 5 m for temperature, carbon dioxide and dimethylsulfide of 0.15 °C, 4 µatm and 0.4 nM respectively.

Tire-road noise: an experimental study of tire and road design parameters

NARCIS (Netherlands)

Bekke, Dirk; Wijnant, Ysbrand H.; Weegerink, Thijs; de Boer, Andries

2013-01-01

It is widely known that road traffic noise has negative influences on human health. Hence, as tire-road noise is considered to be the most dominant cause of road traffic noise above 30-50 km/h, a lot of research is performed by the two involving industries: road authorities/manufacturers and tire

Building Road-Sign Classifiers Using a Trainable Similarity Measure

Czech Academy of Sciences Publication Activity Database

Paclík, P.; Novovičová, Jana; Duin, R.P.W.

2006-01-01

Roč. 7, č. 3 (2006), s. 309-321 ISSN 1524-9050 R&D Projects: GA AV ČR IAA2075302 EU Projects: European Commission(XE) 507752 - MUSCLE Institutional research plan: CEZ:AV0Z10750506 Keywords : classifier system design * road-sign classification * similarity data representation Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 1.434, year: 2006 http://www.ewh.ieee.org/tc/its/trans.html

A Public Health Perspective of Road Traffic Accidents

Directory of Open Access Journals (Sweden)

S Gopalakrishnan

2012-01-01

Full Text Available Road traffic accidents (RTAs have emerged as an important public health issue which needs to be tackled by a multi-disciplinary approach. The trend in RTA injuries and death is becoming alarming in countries like India. The number of fatal and disabling road accident happening is increasing day by day and is a real public health challenge for all the concerned agencies to prevent it. The approach to implement the rules and regulations available to prevent road accidents is often ineffective and half-hearted. Awareness creation, strict implementation of traffic rules, and scientific engineering measures are the need of the hour to prevent this public health catastrophe. This article is intended to create awareness among the health professionals about the various modalities available to prevent road accidents and also to inculcate a sense of responsibility toward spreading the message of road safety as a good citizen of our country.

Genetic Algorithm for Opto-thermal Skin Hydration Depth Profiling Measurements

Science.gov (United States)

Cui, Y.; Xiao, Perry; Imhof, R. E.

2013-09-01

Stratum corneum is the outermost skin layer, and the water content in stratum corneum plays a key role in skin cosmetic properties as well as skin barrier functions. However, to measure the water content, especially the water concentration depth profile, within stratum corneum is very difficult. Opto-thermal emission radiometry, or OTTER, is a promising technique that can be used for such measurements. In this paper, a study on stratum corneum hydration depth profiling by using a genetic algorithm (GA) is presented. The pros and cons of a GA compared against other inverse algorithms such as neural networks, maximum entropy, conjugate gradient, and singular value decomposition will be discussed first. Then, it will be shown how to use existing knowledge to optimize a GA for analyzing the opto-thermal signals. Finally, these latest GA results on hydration depth profiling of stratum corneum under different conditions, as well as on the penetration profiles of externally applied solvents, will be shown.

Demonstrating a correlation between the maturity of road safety practices and road safety incidents.

Science.gov (United States)

Amador, Luis; Willis, Christopher Joseph

2014-01-01

The objective of this study is to demonstrate a correlation between the maturity of a country's road safety practices and road safety incidents. Firstly, data on a number of road injuries and fatalities for 129 countries were extracted from the United Nations Global Status on Road Safety database. These data were subdivided according to road safety incident and accident causation factors and normalized based on vehicular fleet (per 1000 vehicles) and road network (per meter of paved road). Secondly, a road safety maturity model was developed based on an adaptation of the concept of process maturity modeling. The maturity of countries with respect to 10 road safety practices was determined through the identification of indicators recorded in the United Nations Global Status of Road Safety Database. Plots of normalized road safety performance of the 129 countries against their maturity scores for each road safety practice as well as an aggregation of the road safety practices were developed. An analysis of variance was done to determine the extent of the correlation between the road safety maturity of the countries and their performance. In addition, a full Bayesian analysis was done to confirm the correlation of each of the road safety practices with injuries and fatalities. Regression analysis for fatalities, injuries, and combined accidents identified maturity with respect to road safety practices associated with speed limits and use of alternative modes as being the most significant predictors of traffic fatalities. A full Bayesian regression confirms that there is a correlation between the maturity of road safety practices and road safety incidents. Road safety practices associated with enforcement of speed limits and promotion of alternative modes are the most significant road safety practices toward which mature countries have concentrated their efforts, resulting in a lower frequency of fatalities, injury rates, and property damage accidents. The authors

Gravel roads management : volume 1, gravel roads management.

Science.gov (United States)

2010-10-01

This report establishes procedures for managing dirt and gravel roads, with a primary focus on smaller agencies, such as Wyoming counties, that must manage their roads with very limited resources. The report strives, first, to guide and assist smalle...

A method for measuring particle number emissions from vehicles driving on the road.

Science.gov (United States)

Shi, J P; Harrison, R M; Evans, D E; Alam, A; Barnes, C; Carter, G

2002-01-01

Earlier research has demonstrated that the conditions of dilution of engine exhaust gases profoundly influence the size distribution and total number of particles emitted. Since real world dilution conditions are variable and therefore difficult to simulate, this research has sought to develop and validate a method for measuring particle number emissions from vehicles driving past on a road. This has been achieved successfully using carbon dioxide as a tracer of exhaust gas dilution. By subsequent adjustment of data to a constant dilution factor, it is possible to compare emissions from different vehicles using different technologies and fuels based upon real world emission data. Whilst further optimisation of the technique, especially in terms of matching the instrument response times is desirable, the measurements offer useful insights into emissions from gasoline and diesel vehicles, and the substantial proportion of particles emitted in the 3-7 nanometre size range.

Road Traffic Noise Pollution Analysis for Cernavoda City

Science.gov (United States)

Manea, L.; Manea, A.; Florea, D.; Tarulescu, S.

2017-10-01

In the present paper was studied the noise pollution in Cernavodă city. The noise measurements were made for nine intersections from different city areas. Noise measurements were taken for three chosen routes with high population density, heavy traffic, commercial and residential buildings. Average, maximum and minimum values were collected and compared with standards. The impact of road traffic noise on the community depends on various factors such as road location and design, land use planning measures, building design, traffic composition, driver behaviour and the relief. In the study area 9 locations are identified to measure noise level. By using sound level meter noise levels are measured at different peak sessions i.e. morning, afternoon and evening. The presented values were collected for evening rush hour.

Determining the near-surface current profile from measurements of the wave dispersion relation

Science.gov (United States)

Smeltzer, Benjamin; Maxwell, Peter; Aesøy, Eirik; Ellingsen, Simen

2017-11-01

The current-induced Doppler shifts of waves can yield information about the background mean flow, providing an attractive method of inferring the current profile in the upper layer of the ocean. We present measurements of waves propagating on shear currents in a laboratory water channel, as well as theoretical investigations of inversion techniques for determining the vertical current structure. Spatial and temporal measurements of the free surface profile obtained using a synthetic Schlieren method are analyzed to determine the wave dispersion relation and Doppler shifts as a function of wavelength. The vertical current profile can then be inferred from the Doppler shifts using an inversion algorithm. Most existing algorithms rely on a priori assumptions of the shape of the current profile, and developing a method that uses less stringent assumptions is a focus of this study, allowing for measurement of more general current profiles. The accuracy of current inversion algorithms are evaluated by comparison to measurements of the mean flow profile from particle image velocimetry (PIV), and a discussion of the sensitivity to errors in the Doppler shifts is presented.

Wind profiler mixing depth and entrainment measurements with chemical applications

Energy Technology Data Exchange (ETDEWEB)

Angevine, W.M.; Trainer, M.; Parrish, D.D.; Buhr, M.P.; Fehsenfeld, F.C. [NOAA Aeronomy Lab., Boulder, CO (United States); Kok, G.L. [NCAR Research Aviation Facility, Boulder, CO (United States)

1994-12-31

Wind profiling radars operating at 915 MHz have been present at a number of regional air quality studies. The profilers can provide a continuous, accurate record of the depth of the convective mixed layer with good time resolution. Profilers also provide information about entrainment at the boundary layer top. Mixing depth data from several days of the Rural Oxidants in the Southern Environment II (ROSE II) study in Alabama in June, 1992 are presented. For several cases, chemical measurements from aircraft and ground-based instruments are shown to correspond to mixing depth and entrainment zone behavior observed by the profiler.

Road safety and road traffic accidents in Saudi Arabia. A systematic review of existing evidence.

Science.gov (United States)

Mansuri, Farah A; Al-Zalabani, Abdulmohsen H; Zalat, Marwa M; Qabshawi, Reem I

2015-04-01

To identify the changing trends and crucial preventive approaches to road traffic accidents (RTAs) adopted in the Kingdom of Saudi Arabia (KSA) over the last 2.5 decades, and to analyze aspects previously overlooked. This systematic review was based on evidence of RTAs in KSA. All articles published during the last 25 years on road traffic accident in KSA were analyzed. This study was carried out from December 2013 to May 2014 in the Department of Family and Community Medicine, Taibah University, Al-Madinah Al-Munawwarah, KSA. Road traffic accidents accounted for 83.4% of all trauma admissions in 1984-1989, and no such overall trend was studied thereafter. The most frequently injured body regions as reported in the latest studies were head and neck, followed by upper and lower extremities, which was found to be opposite to that of the studies reported earlier. Hospital data showed an 8% non-significant increase in road accident mortalities in contrast to police records of a 27% significant reduction during the years 2005-2010. Excessive speeding was the most common cause reported in all recent and past studies. Disparity was common in the type of reporting of RTAs, outcome measures, and possible causes over a period of 2.5 decade. All research exclusively looked into the drivers' faults. A sentinel surveillance of road crashes should be kept in place in the secondary and tertiary care hospitals for all regions of KSA.

Optical bi-sensorial measurement system for production control of extruded profiles

Science.gov (United States)

Weckenmann, A.; Bernstein, J.

2008-09-01

Extruded profiles are semi-finished products (made out of steel, brass, aluminum, synthetics...) which are appointed for wide applications in manufacturing of technical products. As yet used optical sensors in process control working to the shading technology detect the object's shadow orthographically to the axis of illumination. As a consequence they record it unattached by the profiles coat in measurement range at any point of the measured profile with high precision. As a matter of fact, concave zones cannot be captured. Alternatively the measurement of concave zones can be arranged by light-section systems. These do not comply with the required accuracy, are comparatively slow and moreover affected by dislocations of the section of the profile. A measurement system including a light-section and a shading system combines the advantages of both optical systems. It is to serve with a reliable conception for the assembly of a bi-sensorial measurement system consisting of both systems as well as suitable methods of analysis for the in-line inspection of concave profiles. As a result it contains conclusions concerning requirements of the light source, the arrangement of this source and the cameras, obtainable precision and sampling rate as well as the essential synchronization of both systems. After designing an appropriate prototype, the selected light-section system and the shading system will be synchronized and aligned. Therefore, the metered geometrical data will be merged for the evaluation of form deviation. So, developed and adapted software supports and contains proposals to the uncertainty after successful tests. The system and a calibration method will be proved in production where robustness will be a most critical despite of heat, dust and vibrations. The target uncertainty of less than 0.1 mm at every section of the profiles coat has to be met.

Toroidal equilibrium and radial profiles from magnetic measurements in Extrap T1

International Nuclear Information System (INIS)

Brunsell, Per; Jin Li; Tennfors, Einar

1991-01-01

The toroidal equilibrium position in the Extrap T1 toroidal Z-pinch is studied by measuring the currents induced in the external octupole field rings. Radial profiles are obtained by an internal magnetic coil array. From the magnetic field, profiles of current density, plasma pressure, safety factor, resistivity and input power density are deduced. A polynomial model is developed to simulate the measured profiles. The classical ion heat conduction losses in Extrap discharges are calculated using this model and compared to the power input. for polynomials matched to magnetic field profiles measured in present experiments, these losses are small. By varying the coefficients of the polynomials, a region is found where the power input can balance the classical heat conduction losses at higher values of Θ and β o . (Author)

Road safety: take it seriously

CERN Multimedia

Antonella Del Rosso

2015-01-01

Around 50 road accidents happen every year at CERN. Cyclists, drivers and pedestrians must pay attention to their behaviour at all times to ensure that this doesn’t become an even more serious problem. Even if the Laboratory’s sites are not exactly downtown Shanghai, all road users need to make a little effort. So let’s do it!   Life at CERN: let’s stick to accumulating scientific data rather than road accidents! (Cartoon by Cian O'Luanaigh) Despite a dedicated Safety Code in force since 1990, “traffic-calming” measures put in place last year, several reminders in the Bulletin and frequent safety campaigns, the number of accidents, particularly those involving cyclists, has remained high since 2008. Luckily, no-one has been seriously injured but it is more and more frequent to experience near misses or actual accidents, whether in a car or on a bike. Incivilities, excessive speeding (also for bikes!) and answering ...

Road safety: serious injuries remain a major unsolved problem.

Science.gov (United States)

Beck, Ben; Cameron, Peter A; Fitzgerald, Mark C; Judson, Rodney T; Teague, Warwick; Lyons, Ronan A; Gabbe, Belinda J

2017-09-18

To investigate temporal trends in the incidence, mortality, disability-adjusted life-years (DALYs), and costs of health loss caused by serious road traffic injury. A retrospective review of data from the population-based Victorian State Trauma Registry and the National Coronial Information System on road traffic-related deaths (pre- and in-hospital) and major trauma (Injury Severity Score > 12) during 2007-2015.Main outcomes and measures: Temporal trends in the incidence of road traffic-related major trauma, mortality, DALYs, and costs of health loss, by road user type. There were 8066 hospitalised road traffic major trauma cases and 2588 road traffic fatalities in Victoria over the 9-year study period. There was no change in the incidence of hospitalised major trauma for motor vehicle occupants (incidence rate ratio [IRR] per year, 1.00; 95% CI, 0.99-1.01; P = 0.70), motorcyclists (IRR, 0.99; 95% CI, 0.97-1.01; P = 0.45) or pedestrians (IRR, 1.00; 95% CI, 0.97-1.02; P = 0.73), but the incidence for pedal cyclists increased 8% per year (IRR, 1.08; 95% CI; 1.05-1.10; P road traffic injuries exceeded $14 billion during 2007-2015, although the cost per patient declined for all road user groups. As serious injury rates have not declined, current road safety targets will be difficult to meet. Greater attention to preventing serious injury is needed, as is further investment in road safety, particularly for pedal cyclists.

Sustainable road safety: a new (?) neighbourhood road pattern that saves VRU lives.

Science.gov (United States)

Wei, Vicky Feng; Lovegrove, Gord

2012-01-01

Both the UN (2007) and World Health Organizations (2004) have declared the enormous social and economic burden imposed on society by injuries due to road collisions as a major global problem. While the road safety problem is not new, this prominent global declaration sends an important signal of frustration regarding progress to date on reducing road collisions. It is clear that governments, communities, businesses and the public must discover ways of reducing this burden, especially as it relates to vulnerable road users (VRUs), typically meaning pedestrian and bicyclist road users. Recent comparisons of global VRU collisions statistics suggest that, in addition to mixed land use density, the layout of neighbourhood roads plays a vital role in the encouragement of walkable, safe and quiet, yet accessible and sustainable communities. The purpose of this paper was to: The Dutch Sustainable Road Safety (SRS) Program has produced a number of innovative land use and transportation initiatives for vehicular road users as well as non-vehicular VRUs. Following from the Dutch initiatives, these new 3-way offset, and fused grid neighbourhood patterns appear to not only have positive effects in encouraging mode split (i.e. increasing walking and bicycling, and transit), slowing traffic, and reducing energy consumption and GHG emissions; but also, to hold potential to improve road safety. To test the road safety hypothesis, UBCO researchers evaluated the level of road safety relative to five neighbourhood patterns - grid, culs-de-sac, and Dutch Sustainable Road Safety (SRS) (or limited access), 3-way offset, and fused grid networks. Analysis using standard transportation planning methodology revealed that they would maintain both mobility and accessibility. Analysis using standard road safety analysis methodology further revealed that these 3-way offset, and fused grid patterns would significantly improve road safety levels by as much as 60% compared to prevalent patterns (i

Apparatus for measuring profile thickness of strip material

International Nuclear Information System (INIS)

Hold, A.C.

1982-01-01

Apparatus for measuring the thickness profile of steel strip comprises a radiation source reciprocally movable in a stepwise fashion (by a belt) across the strip width on one side thereof and a single elongated detector on the other side of the strip aligned with the scanning source. This detector may be a fluorescent scintillator detector or an ionisation chamber. Means are provided for sensing the degree of excitation in the detector in synchronism with the scanning source whereby to provide an output representative of the thickness profile of the strip. (author)

Advanced receptor modelling for the apportionment of road dust resuspension to atmospheric PM

Science.gov (United States)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

2009-04-01

Fugitive emissions from traffic resuspension can often represent an important source of atmospheric particulate matter in urban environments, especially when the scarce precipitations favour the accumulation of road dust. Resuspension of road dust can lead to high exposures to heavy metals, metalloids and mineral matter. Knowing the amount of its contribution to atmospheric PM is a key task for establishing eventual mitigation or preventive measures. Factor analysis techniques are widely used tools for atmospheric aerosol source apportionment, based on the mass conservation principle. Paatero and Tapper (1993) suggested the use of a Weighted Least Squares scheme with the aim of obtaining a minimum variance solution. Additionally they proposed to incorporate the basic physical constraint of non negativity, calling their approach Positive Matrix Factorization (PMF), which can be performed by the program PMF2 released by Paatero (1997). Nevertheless, Positive Matrix Factorization can be either solved with the Multilinear Engine (ME-2), a more flexible program, also developed by Paatero (1999), which can solve any model consisting in sum of products of unknowns. The main difference with PMF2 is that ME-2 does not solve only well-defined tasks, but its actions are defined in a "script file" written in a special-purpose programming language, allowing incorporating additional tasks such as data processing etc. Thus in ME-2 a priori information, e.g. chemical fingerprints can be included as auxiliary terms of the object function to be minimized. This feature of ME-2 make it especially suitable for source apportionment studies where some knowledge (chemical ratios, profiles, mass conservation etc) of involved sources is available. The aim of this study was to quantify the contribution of road dust resuspension in PM10, PM2.5 and PM1 data set from Barcelona (Spain). Given that recently the emission profile of local road dust was characterized (Amato et al., in press

Road Closures

Data.gov (United States)

Montgomery County of Maryland — This is an up to date map of current road closures in Montgomery County.This dataset is updated every few minutes from the Department of Transportation road closure...

A comprehensive conceptual framework for road safety strategies.

Science.gov (United States)

Hughes, B P; Anund, A; Falkmer, T

2016-05-01

Road safety strategies (generally called Strategic Highway Safety Plans in the USA) provide essential guidance for actions to improve road safety, but often lack a conceptual framework that is comprehensive, systems theory based, and underpinned by evidence from research and practice. This paper aims to incorporate all components, policy tools by which they are changed, and the general interactions between them. A framework of nine mutually interacting components that contribute to crashes and ten generic policy tools which can be applied to reduce the outcomes of these crashes was developed and used to assess 58 road safety strategies from 22 countries across 15 years. The work identifies the policy tools that are most and least widely applied to components, highlighting the potential for improvements to any individual road safety strategy, and the potential strengths and weaknesses of road safety strategies in general. The framework also provides guidance for the development of new road safety strategies, identifying potential consequences of policy tool based measures with regard to exposure and risk, useful for both mobility and safety objectives. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessing costs and effectiveness of safety measures for the transit of small type a packages through road tunnels

International Nuclear Information System (INIS)

Hubert, P.; Pages, P.; Ringot, C.; Tomachevsky, E.; Hamard, J.

1986-06-01

The 12 km long Mont Blanc Tunnel, is one of the longest road tunnels. Local authorities have to state whether the general regulations for the road transportation of radioactive materials, as defined by the IAEA, apply, or whether additive measures need to be taken. Whereas an activity limit - A 2 - applies only to the content of a type A package containing dispersible materials, a derived limit applying to the whole cargo of a truck has been in use in the tunnel and can be redefined. The present paper deals with the question of the choice of a proper figure for such a limit, that might regulate the transit under the tunnel for Technetium generators (ELUMATIC III from ORIS FRANCE). The first step is a risk assessment, with the truck content as an explicit parameter. The yearly traffic is of 150 trucks, carrying, on the average, 26 Ci of Technetium 99m on a yearly basis, about 5.10 -6 road accidents might be expected, while the expected radiological fatalities would amount to approximately 2.10 -8 and the expected monetary loss would be dollars 10. The second step is the implementation of decision aiding techniques based on the previous estimates

Head-on crashes on two-way interurban roads: a public health concern in road safety.

Science.gov (United States)

Olabarria, Marta; Santamariña-Rubio, Elena; Marí-Dell'Olmo, Marc; Gotsens, Mercè; Novoa, Ana M; Borrell, Carme; Pérez, Katherine

2015-09-01

To describe the magnitude and characteristics of crashes and drivers involved in head-on crashes on two-way interurban roads in Spain between 2007 and 2012, and to identify the factors associated with the likelihood of head-on crashes on these roads compared with other types of crash. A cross-sectional study was conducted using the National Crash Register. The dependent variables were head-on crashes with injury (yes/no) and drivers involved in head-on crashes (yes/no). Factors associated with head-on crashes and with being a driver involved in a head-on crash versus other types of crash were studied using a multivariate robust Poisson regression model to estimate proportion ratios (PR) and confidence intervals (95% CI). There were 9,192 head-on crashes on two-way Spanish interurban roads. A total of 15,412 men and 3,862 women drivers were involved. Compared with other types of crash, head-on collisions were more likely on roads 7 m or more wide, on road sections with curves, narrowings or drop changes, on wet or snowy surfaces, and in twilight conditions. Transgressions committed by drivers involved in head-on crashes were driving in the opposite direction and incorrectly overtaking another vehicle. Factors associated with a lower probability of head-on crashes were the existence of medians (PR=0.57; 95%CI: 0.48-0.68) and a paved shoulder of less than 1.5 meters (PR=0.81; 95%CI: 0.77-0.86) or from 1.5 to 2.45 meters (PR=0.90; 95%CI: 0.84-0.96). This study allowed the characterization of crashes and drivers involved in head-on crashes on two-way interurban roads. The lower probability observed on roads with median strips point to these measures as an effective way to reduce these collisions. Copyright © 2014 SESPAS. Published by Elsevier Espana. All rights reserved.

A measurement system for vertical seawater profiles close to the air–sea interface

Directory of Open Access Journals (Sweden)

R. P. Sims

2017-09-01

Full Text Available This paper describes a near-surface ocean profiler, which has been designed to precisely measure vertical gradients in the top 10 m of the ocean. Variations in the depth of seawater collection are minimized when using the profiler compared to conventional CTD/rosette deployments. The profiler consists of a remotely operated winch mounted on a tethered yet free-floating buoy, which is used to raise and lower a small frame housing sensors and inlet tubing. Seawater at the inlet depth is pumped back to the ship for analysis. The profiler can be used to make continuous vertical profiles or to target a series of discrete depths. The profiler has been successfully deployed during wind speeds up to 10 m s−1 and significant wave heights up to 2 m. We demonstrate the potential of the profiler by presenting measured vertical profiles of the trace gases carbon dioxide and dimethylsulfide. Trace gas measurements use an efficient microporous membrane equilibrator to minimize the system response time. The example profiles show vertical gradients in the upper 5 m for temperature, carbon dioxide and dimethylsulfide of 0.15 °C, 4 µatm and 0.4 nM respectively.

Risk management model in road transport systems

Science.gov (United States)

Sakhapov, R. L.; Nikolaeva, R. V.; Gatiyatullin, M. H.; Makhmutov, M. M.

2016-08-01

The article presents the results of a study of road safety indicators that influence the development and operation of the transport system. Road safety is considered as a continuous process of risk management. Authors constructed a model that relates the social risks of a major road safety indicator - the level of motorization. The model gives a fairly accurate assessment of the level of social risk for any given level of motorization. Authors calculated the dependence of the level of socio-economic costs of accidents and injured people in them. The applicability of the concept of socio-economic damage is caused by the presence of a linear relationship between the natural and economic indicators damage from accidents. The optimization of social risk is reduced to finding the extremum of the objective function that characterizes the economic effect of the implementation of measures to improve safety. The calculations make it possible to maximize the net present value, depending on the costs of improving road safety, taking into account socio-economic damage caused by accidents. The proposed econometric models make it possible to quantify the efficiency of the transportation system, allow to simulate the change in road safety indicators.

Measurement of mobility profile in ion-implanted silicon layers using electroreflection spectroscopy

International Nuclear Information System (INIS)

Galiev, G.B.; Kapaev, V.V.; Mokerov, V.G.

1986-01-01

The possibility is shown of the application of the low field linearized electroreflection spectroscopy for the measurement of profiles of carriers mobilities μ(x) simultaneously with the concentration profiles N(x) in thin ion-implanted silicon layers. The μ(χ) value is determined from the calibration curve of the dependence of the phenomenological broadening parameter γ on the mobility for uniformly doped samples. The results are presented for the measurements of the profiles μ(x) for boron- and arsenic-implanted silicon

Road rage and road traffic accidents among commercial vehicle drivers in Lahore, Pakistan.

Science.gov (United States)

Shaikh, M A; Shaikh, I A; Siddiqui, Z

2012-04-01

Road rage and road traffic accidents increase the burden of morbidity and mortality in a population. A cross-sectional survey with convenience sampling was conducted among commercial vehicle drivers in Lahore, Pakistan (n = 901) to record their behaviours/experiences regarding road rage and road traffic accidents. Respondents were asked about incidents of shouting/cursing/rude gestures or threats to physically hurt the person/vehicle, by others or themselves, in the previous 24 hours or 3 months, and their involvement in road traffic accidents in the previous 12 months. Auto-rickshaw drivers were significantly more likely to report various road rage experiences/behaviours and involvement in accidents compared with bus and wagon drivers. A total of 112 respondents (12.4%) reported being involved in a road traffic accident in the previous 12 months but traffic police did not record the accident in 52.7% of cases. The results of this study underline the need to improve road safety in Pakistan.

Management of roads with abnormal radiation

International Nuclear Information System (INIS)

Chen Wenfang; Huang Jehnying; Chin, Chingjer; Chen Yibin

2002-01-01

Several asphalt concrete (AC) roads in Taoyuan County of Taiwan were found radioactively abnormal in 1994. Atomic Energy Council (AEC), the regulatory agency, was asked to take the samples, to perform the radiochemical analysis and dose evaluation as well as to investigate the source of contamination. The cause of high radiation was due to high uranium and thorium concentration slag used in the AC. The dose rate was approximately 1 μSv/hr at the road surface. The maximum annual dose received by pedestrians was estimated at 0.13 mSv (2.5% of annual dose limit of 5 mSv for the public), or approximately 1/15 of the value of annual natural background radiation in the Taiwan area. Consequently, the AEC suggested that there was no need to implement engineering remedy measures to remove the AC surface of the roads. However, upon consideration of socioeconomic condition and public opinion, the local government still decided to remove the contaminated surface of these roads. The AEC helped to formulate the operational procedures for removal and disposal of the AC including the radiation protection program and the disposal site. To date, all the contaminated AC surface of the roads was removed and properly disposed. The contaminated AC roads are a typical example of improper disposal of wastes containing Technologically Enhanced Naturally Occurring Radioactive Materials (TENORM). A new regulation was promulgated by AEC recently to limit the use of slag, coal ash or any other industrial wastes unless its radiation or activity level is below the limit. (author)

Small-scale geodiversity and dirt road management, Ede (NL)

Science.gov (United States)

van den Ancker, Hanneke; Jungerius, Pieter Dirk

2016-04-01

A large part of the countryside roads on the Pleistocene sands of The Netherlands are dirt roads. Most are footpaths, but a small percentage are relatively heavily used by motorized vehicles. These latter roads are a cause subject of debate. Puddles and potholes develop during periods of wet weather, while dust whirls from the roads form during spells of dry weather as do washboard ripples. They cause problems for people living along these roads and tourists (walkers and bikers. The community of Ede (NL), like many other communities on the sand, wants to keep its 80 km of dirt roads because of the natural values they harbour as well as for their characteristic landscape quality and cultural heritage value. A part of the dirt roads in Ede is heavily used. In 2009, the community of Ede developed a decision model to support management of the dirt roads. Ede acknowledges that each dirt road is unique and asks for a tailor-made solution. Road maintenance measures include grading, making a camber, digging pits, applying loam or sandy loam. If problems become too large, one-way traffic can be an option. In more and more cases the dirt roads are barred for motorized through traffic (Gemeente Ede, 2009). As a reconnaissance we have studied the dirt roads of the Horabos/Horalaan over the last year. Incidentally we looked at other parts of the main Horalaan and the footpaths in the adjacent forest of Hoekelum. All dirt roads lie near the top of a Saalian push-moraine in which the upper course of dry valleys are present. Some results of the reconnaissance: - Most dirt roads sections in the Horabos lie lower than the surrounding terrain; - The problems develop in a short period of time during special weather conditions; - Certain dirt road sections e.g. those sections crossing a slight depression are quickly developing potholes; - Even a small slope of the road (differences that have consequences for its maintenance. Knowledge of geodiversity of the terrain and study of small

ENHANCEMENT OF ROAD SAFETY THROUGH MORE EFFECTIVE ROAD AND TRAFFIC MANAGEMENT

Directory of Open Access Journals (Sweden)

Tomasz SZCZURASZEK

2016-07-01

Full Text Available To make the policy aimed at mitigating the risk of road incidents more effective, Poland should see the introduction of the more efficient road and traffic management. In November 2008 the European Parliament and the European Council published the Directive on "infrastructure safety management" which provides guidance on the procedures for carrying impact assessments of traffic safety, traffic safety audits, safety management on the road network and monitoring traffic safety in Member States. In this article, the authors have proposed a systemic approach to road and traffic management, involving the implementation of consistent procedures that should include regular revisions of roads, eliminating hazardous sites, speed management, as well as the approval and implementation of traffic organization designs.

The driver, the road, the rules … and the rest? A systems-based approach to young driver road safety.

Science.gov (United States)

Scott-Parker, B; Goode, N; Salmon, P

2015-01-01

The persistent overrepresentation of young drivers in road crashes is universally recognised. A multitude of factors influencing their behaviour and safety have been identified through methods including crash analyses, simulated and naturalistic driving studies, and self-report measures. Across the globe numerous, diverse, countermeasures have been implemented; the design of the vast majority of these has been informed by a driver-centric approach. An alternative approach gaining popularity in transport safety is the systems approach which considers not only the characteristics of the individual, but also the decisions and actions of other actors within the road transport system, along with the interactions amongst them. This paper argues that for substantial improvements to be made in young driver road safety, what has been learnt from driver-centric research needs to be integrated into a systems approach, thus providing a holistic appraisal of the young driver road safety problem. Only then will more effective opportunities and avenues for intervention be realised. Copyright © 2014 Elsevier Ltd. All rights reserved.

Future of energy efficiency and carbon dioxide emissions of Finnish road freight transport

Energy Technology Data Exchange (ETDEWEB)

Liimatainen, H.

2013-05-15

The targets to reduce the carbon dioxide emissions to mitigate climate change are as much applicable to the road freight transport sector as they are to all other sectors of society. The aim of this research is to support the initiatives of the Finnish government for improving the energy efficiency and reducing the CO{sub 2} emissions of road freight transport. This is done by forecasting the future development and giving the policy makers guidance on effective measures for promoting road freight energy efficiency and CO{sub 2} reduction. In the study a new method was introduced for connecting the fuel consumption data and goods transport data gathered from the official Finnish road statistics. This method enabled a detailed analysis of the interrelations between the economy, road freight transport, energy consumption and emissions. This analysis was conducted for the years 1995-2010 and the results were used as background information in the Delphi panel of experts. The experts estimated the development of the Finnish road freight sector to the year 2030. Furthermore, a web-based survey was conducted among Finnish road freight hauliers and shippers in order to explore the attitudes and measures related to the energy efficiency. Expert panel workshops were also organised to identify obstacles for the development of the energy efficiency of road freight transport as well as a wide selection of measures to overcome them. The results indicate that the economic development of different branches has a great effect on the energy efficiency and carbon dioxide emissions of road freight transport. Reaching the carbon emission target for the year 2030 is possible in the light of the scenarios which were formed based on expert forecasts. However, the target can be achieved with very different development paths, e.g. the structure of the national economy and the volume of transport seem to vary widely in the different scenarios. In the proposed recommendations on the measures

On street observations of particulate matter movement and dispersion due to traffic on an urban road

Science.gov (United States)

Patra, Aditya; Colvile, Roy; Arnold, Samantha; Bowen, Emma; Shallcross, Dudley; Martin, Damien; Price, Catheryn; Tate, James; ApSimon, Helen; Robins, Alan

Empirical models for particulate matter emissions from paved road surfaces have been criticised for their lack of realism and accuracy. To support the development of a less empirical model, a study was conducted in a busy street at the DAPPLE site in Central London to understand the processes and to identify important parameters that influence emission from paved roads. Ordinary road gritting salt was applied to the road and the particulate matter entering the air at near-road surface level was monitored using optical particle counters. The grit acted as a tracer. The grit moved rapidly along the road in the direction of traffic flow. Build-up of material at the kerb indicated material being thrown across the road by the traffic. Coarser particles were resuspended faster than the finer ones. A clear decay profile was seen in the case of particles larger than 2μm; particles smaller than 2μm did not show any decay pattern during the experiment duration. Grinding of material appears to control the reservoir of fine particles on the road surface. The amount of material resuspended by traffic is about 30% less than those removed along the road and a factor of 6 higher than the amount removed across the road. Resuspension accounts for 40% of the total material removed from a road segment and 70% of the material removed together along and across the road. On average a single vehicle pass removes 0.08% of material present on a road segment at that instant. The calculation scheme is obtained from a short-duration study and therefore further studies of long duration involving varying road geometry and different traffic and meteorological condition need to be carried out before applying parameter estimates presented in this paper.

Beam profile measurement of ES-200 using secondary electron emission monitor

Directory of Open Access Journals (Sweden)

E Ebrahimi Basabi

2015-09-01

Full Text Available Up to now, different designs have been introduced for measurement beam profile accelerators. Secondary electron emission monitors (SEM are one of these devices which have been used for this purpose. In this work, a SEM has been constructed to measure beam profile of ES-200 accelerator, a proton electrostatic accelerator which is installed at SBU. Profile grid for both planes designed with 16 wires which are insulated relative to each other. The particles with maximum energy of 200 keV and maximum current of 400 μA are stopped in copper wires. Each of the wires has an individual current-to-voltage amplifier. With a multiplexer, the analogue values are transported to an ADC. The ADCs are read out by a microcontroller and finally profile of beam shows by a user interface program

Assessing and Mapping of Road Surface Roughness based on GPS and Accelerometer Sensors on Bicycle-Mounted Smartphones

Science.gov (United States)

Shen, Jie; Wan, Mi; Shi, Jiafeng

2018-01-01

The surface roughness of roads is an essential road characteristic. Due to the employed carrying platforms (which are often cars), existing measuring methods can only be used for motorable roads. Until now, there has been no effective method for measuring the surface roughness of un-motorable roads, such as pedestrian and bicycle lanes. This hinders many applications related to pedestrians, cyclists and wheelchair users. In recognizing these research gaps, this paper proposes a method for measuring the surface roughness of pedestrian and bicycle lanes based on Global Positioning System (GPS) and accelerometer sensors on bicycle-mounted smartphones. We focus on the International Roughness Index (IRI), as it is the most widely used index for measuring road surface roughness. Specifically, we analyzed a computing model of road surface roughness, derived its parameters with GPS and accelerometers on bicycle-mounted smartphones, and proposed an algorithm to recognize potholes/humps on roads. As a proof of concept, we implemented the proposed method in a mobile application. Three experiments were designed to evaluate the proposed method. The results of the experiments show that the IRI values measured by the proposed method were strongly and positively correlated with those measured by professional instruments. Meanwhile, the proposed algorithm was able to recognize the potholes/humps that the bicycle passed. The proposed method is useful for measuring the surface roughness of roads that are not accessible for professional instruments, such as pedestrian and cycle lanes. This work enables us to further study the feasibility of crowdsourcing road surface roughness with bicycle-mounted smartphones. PMID:29562731

Inroads into Equestrian Safety: Rider-Reported Factors Contributing to Horse-Related Accidents and Near Misses on Australian Roads

Directory of Open Access Journals (Sweden)

Kirrilly Thompson

2015-07-01

Full Text Available Horse riding and horse-related interactions are inherently dangerous. When they occur on public roads, the risk profile of equestrian activities is complicated by interactions with other road users. Research has identified speed, proximity, visibility, conspicuity and mutual misunderstanding as factors contributing to accidents and near misses. However, little is known about their significance or incidence in Australia. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52% reported having experienced at least one accident or near miss in the 12 months prior to the survey. Whilst our findings confirm the factors identified overseas, we also identified issues around rider misunderstanding of road rules and driver misunderstanding of rider hand signals. Of particular concern, we also found reports of potentially dangerous rider-directed road rage. We identify several areas for potential safety intervention including (1 identifying equestrians as vulnerable road users and horses as sentient decision-making vehicles (2 harmonising laws regarding passing horses, (3 mandating personal protective equipment, (4 improving road signage, (5 comprehensive data collection, (6 developing mutual understanding amongst road-users, (7 safer road design and alternative riding spaces; and (8 increasing investment in horse-related safety initiatives.

Inroads into Equestrian Safety: Rider-Reported Factors Contributing to Horse-Related Accidents and Near Misses on Australian Roads.

Science.gov (United States)

Thompson, Kirrilly; Matthews, Chelsea

2015-07-22

Horse riding and horse-related interactions are inherently dangerous. When they occur on public roads, the risk profile of equestrian activities is complicated by interactions with other road users. Research has identified speed, proximity, visibility, conspicuity and mutual misunderstanding as factors contributing to accidents and near misses. However, little is known about their significance or incidence in Australia. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52%) reported having experienced at least one accident or near miss in the 12 months prior to the survey. Whilst our findings confirm the factors identified overseas, we also identified issues around rider misunderstanding of road rules and driver misunderstanding of rider hand signals. Of particular concern, we also found reports of potentially dangerous rider-directed road rage. We identify several areas for potential safety intervention including (1) identifying equestrians as vulnerable road users and horses as sentient decision-making vehicles (2) harmonising laws regarding passing horses, (3) mandating personal protective equipment, (4) improving road signage, (5) comprehensive data collection, (6) developing mutual understanding amongst road-users, (7) safer road design and alternative riding spaces; and (8) increasing investment in horse-related safety initiatives.

Measurement of plasma edge profile on Wendelstein 7-X

Energy Technology Data Exchange (ETDEWEB)

Drews, Philipp; Liang, Yunfeng; Neubauer, Olaf; Denner, Peter; Rack, Michael; Liu, Shaocheng; Wang, Nunchao; Nicolai, Dirk; Hollfeld, Klaus; Satheeswaran, Guruparan [Forschungszentrum Juelich, IEK4, Juelich (Germany); Grulke, Olaf [Max-Planck-Institut fuer Plasmaphysik, Greifswald (Germany); Collaboration: W7-X Team

2016-07-01

Wendelstein 7-X (W7-X), currently under commissioning at the IPP Greifswald, will be the world's largest stellarator with modular superconducting coils, which will enable steady-state-like plasma operation of up to thirty minutes in order to explore the reactor relevance of this concept. The first operation phase of W7-X will employ a limiter configuration. It will be used primarily for setting up the diagnostics and testing the magnetic configuration. In conjunction with the multipurpose manipulator, a fast reciprocating probe is installed. The combined probe head will be used to measure the radial distribution of the magnetic field using magnetic pick-up coils; the plasma temperature and density profiles and the radial electric field using Langmuir pins; and the plasma flows using a Mach setup. As a quasi-isodynamic stellarator, it has been predicted that not only neoclassical but also turbulent transport will be comparable to or possibly even lower than that of tokamaks. Edge plasma profile measurements, especially those of the electron temperature and density, will play a key role in validating this performance in comparison to the tokamak and hence the viability of a stellarator fusion reactor. The edge plasma profile measurements using the combined probe head are presented.

The effect of proximity to major roads on indoor air quality in typical Australian dwellings

Science.gov (United States)

Lawson, Sarah J.; Galbally, Ian E.; Powell, Jennifer C.; Keywood, Melita D.; Molloy, Suzie B.; Cheng, Min; Selleck, Paul W.

2011-04-01

An Indoor Air Quality Study of residential dwellings was carried out in Melbourne, Australia, and a subset of the data was analysed to investigate the effect of proximity to major roads on indoor air quality (IAQ). Seven-day measurements of PM 10, NO 2, benzene, toluene, ethylbenzene and xylenes, along with continuous CO and PM 2.5 measurements were utilised. The measurements were made indoors and outdoors in 27 dwellings; 15 Near Road (300 m from a major road). Dwellings were sampled for one week each in Winter/Spring 2008 and Summer/Autumn 2009, over an eight month period. Analysis of 7-day measurements showed that NO 2 and toluene were elevated at the 5% significance level both indoors and outdoors at Near Road Dwellings compared to Far Road Dwellings. Indoor/Outdoor (I/O) ratios of NO 2 and toluene were not significantly different between Near and Far Road dwellings giving no evidence of any anomalous dominant indoor source for NO 2 and toluene in Near Road dwellings. Indoor NO 2 was significantly correlated to gas stovetop and oven use in both Near and Far Road dwellings. In the absence of gas cooking, indoor NO 2 was elevated in Near Road dwellings relative to Far Road dwellings by approximately 4 ppb and this can be attributed to infiltration of outdoor air. I/O ratios for NO 2 were 2 indicating that indoor sources dominate with minor contribution from outdoors. Hence the relative contribution of roadways to indoor NO 2 is potentially greater than the relative contribution of roadways to indoor toluene. Findings elsewhere suggest that a similar outdoor enhancement of traffic related NO 2 (˜5 ppb) increases risk of lung cancer and childhood asthma ( Brauer et al., 2000; Nyberg et al., 2000). A simple conceptual model indicated spatial and temporal variance in the concentrations was the biggest limitation in detecting roadway influence outside Near Road dwellings for PM 10, PM 2.5 and NO 2 while measurement uncertainty was also important for CO.

Meta-Analysis on Near-Road Air Pollutants Concentrations for Developing Traffic Indicators for Exposure Assessment

Science.gov (United States)

Near-road air pollution has been associated with various health risks in human populations living near roadways. To better understand relationship between vehicle emissions and spatial profiles of traffic-related air pollutants we performed a comprehensive and systematic literat...

Explaining the road accident risk: weather effects.

Science.gov (United States)

Bergel-Hayat, Ruth; Debbarh, Mohammed; Antoniou, Constantinos; Yannis, George

2013-11-01

This research aims to highlight the link between weather conditions and road accident risk at an aggregate level and on a monthly basis, in order to improve road safety monitoring at a national level. It is based on some case studies carried out in Work Package 7 on "Data analysis and synthesis" of the EU-FP6 project "SafetyNet-Building the European Road Safety Observatory", which illustrate the use of weather variables for analysing changes in the number of road injury accidents. Time series analysis models with explanatory variables that measure the weather quantitatively were used and applied to aggregate datasets of injury accidents for France, the Netherlands and the Athens region, over periods of more than 20 years. The main results reveal significant correlations on a monthly basis between weather variables and the aggregate number of injury accidents, but the magnitude and even the sign of these correlations vary according to the type of road (motorways, rural roads or urban roads). Moreover, in the case of the interurban network in France, it appears that the rainfall effect is mainly direct on motorways--exposure being unchanged, and partly indirect on main roads--as a result of changes in exposure. Additional results obtained on a daily basis for the Athens region indicate that capturing the within-the-month variability of the weather variables and including it in a monthly model highlights the effects of extreme weather. Such findings are consistent with previous results obtained for France using a similar approach, with the exception of the negative correlation between precipitation and the number of injury accidents found for the Athens region, which is further investigated. The outlook for the approach and its added value are discussed in the conclusion. Copyright © 2013. Published by Elsevier Ltd.

Comparison of neutral density profiles measured using Dα and C5+ in NSTX-U

Science.gov (United States)

Bell, R. E.; Scotti, F.; Diallo, A.; Leblanc, B. P.; Podesta, M.; Sabbagh, S. A.

2017-10-01

Edge neutral density profiles determined from two different measurements are compared on NSTX-U plasmas. Neutral density measurements were not typical on NSTX plasmas. An array of fibers dedicated to the measurement of passive emission of C5+, used to subtract background emission for charge exchange recombination spectroscopy (CHERS), can be used to infer deuterium neutral density near the plasma edge. The line emission from C5+ is dominated by charge exchange with neutral deuterium near the plasma edge. An edge neutral density diagnostic consisting of a camera with a Dα filter was installed on NSTX-U. The line-integrated measurements from both diagnostics are inverted to obtain local emissivity profiles. Neutral density is then inferred using atomics rates from ADAS and profile measurements from Thomson scattering and CHERS. Comparing neutral density profiles from the two diagnostic measurements helps determine the utility of using the more routinely available C5+ measurements for neutral density profiles. Initial comparisons show good agreement between the two measurements inside the separatrix. Supported by US DoE Contracts DE-AC02-09CH11466 and DE-AC52-07NA27344.

The Potential of Road Pricing Schemes for Reducing Carbon Emissions

Energy Technology Data Exchange (ETDEWEB)

Nocera, S.; Giaretta, F.; Cavallaro, F.

2016-07-01

Road pricing is a transport measure mainly conceived to fund road management, to regulate the demand for traffic and to reduce the number of private vehicles circulating in urban areas. It can also grant benefits in terms of environmental externalities including the reduction of CO2 emissions, which has recently become one of the most important elements defining the sustainability of a transport system. However, the carbon potential granted by road charging is rarely assessed, thus confirming a sort of secondary role attributed to CO2 in urban premises. This paper provides an accurate analysis of the relationship between the different forms of road pricing (including distance-based, congestion-based and pay-as-you-drive) and their effective role in terms of carbon reduction, which in some contexts is higher than 10%. Furthermore, practical suggestions to policy makers in terms of implementation of the measure are discussed, highlighting the precautions necessary to include a fair carbon evaluation into an overall effective analysis. (Author)

Analysis of the Influence of Fibre Diameter on Wirescanner Beam Profile Measurements

CERN Document Server

King, Quentin

1988-01-01

It is often important to be able to measure beam profiles in regions where the beam size is very small. Following concern that the profile measurement might be affected by having a beam size of the same order as the diameter of the wirescanner fibre, the effect was analysed numerically, and the results are presented.

Novel method for on-road emission factor measurements using a plume capture trailer.

Science.gov (United States)

Morawska, L; Ristovski, Z D; Johnson, G R; Jayaratne, E R; Mengersen, K

2007-01-15

The method outlined provides for emission factor measurements to be made for unmodified vehicles driving under real world conditions at minimal cost. The method consists of a plume capture trailer towed behind a test vehicle. The trailer collects a sample of the naturally diluted plume in a 200 L conductive bag and this is delivered immediately to a mobile laboratory for subsequent analysis of particulate and gaseous emissions. The method offers low test turnaround times with the potential to complete much larger numbers of emission factor measurements than have been possible using dynamometer testing. Samples can be collected at distances up to 3 m from the exhaust pipe allowing investigation of early dilution processes. Particle size distribution measurements, as well as particle number and mass emission factor measurements, based on naturally diluted plumes are presented. A dilution profile relating the plume dilution ratio to distance from the vehicle tail pipe for a diesel passenger vehicle is also presented. Such profiles are an essential input for new mechanistic roadway air quality models.

Depth profile measurement with lenslet images of the plenoptic camera

Science.gov (United States)

Yang, Peng; Wang, Zhaomin; Zhang, Wei; Zhao, Hongying; Qu, Weijuan; Zhao, Haimeng; Asundi, Anand; Yan, Lei

2018-03-01

An approach for carrying out depth profile measurement of an object with the plenoptic camera is proposed. A single plenoptic image consists of multiple lenslet images. To begin with, these images are processed directly with a refocusing technique to obtain the depth map, which does not need to align and decode the plenoptic image. Then, a linear depth calibration is applied based on the optical structure of the plenoptic camera for depth profile reconstruction. One significant improvement of the proposed method concerns the resolution of the depth map. Unlike the traditional method, our resolution is not limited by the number of microlenses inside the camera, and the depth map can be globally optimized. We validated the method with experiments on depth map reconstruction, depth calibration, and depth profile measurement, with the results indicating that the proposed approach is both efficient and accurate.

Wildlife friendly roads: the impacts of roads on wildlife in urban areas and potential remedies

Science.gov (United States)

Riley, Seth P D; Brown, Justin L.; Sikich, Jeff A.; Schoonmaker, Catherine M.; Boydston, Erin E.

2014-01-01

Roads are one of the most important factors affecting the ability of wildlife to live and move within an urban area. Roads physically replace wildlife habitat and often reduce habitat quality nearby, fragment the remaining habitat, and cause increased mortality through vehicle collisions. Much ecological research on roads has focused on whether animals are successfully crossing roads, or if the road is a barrier to wildlife movement, gene flow, or functional connectivity. Roads can alter survival and reproduction for wildlife, even among species such as birds that cross roads easily. Here we examine the suite of potential impacts of roads on wildlife, but we focus particularly on urban settings. We report on studies, both in the literature and from our own experience, that have addressed wildlife and roads in urban landscapes. Although road ecology is a growing field of study, relatively little of this research, and relatively few mitigation projects, have been done in urban landscapes. We also draw from the available science on road impacts in rural areas when urban case studies have not fully addressed key topics.

Testing Re-entrained Aerosol Kinetic Emissions from Roads : a new approach to infer silt loading on roadways

Science.gov (United States)

Kuhns, H.; Etyemezian, V.; Landwehr, D.; MacDougall, C.; Pitchford, M.; Green, M.

PM 10 and PM 2.5 emissions from roadways are currently estimated using the silt loading on the road surface as a surrogate for the emissions potential of road dust. While the United States Environmental Protection Agency prescribes this method in AP-42, there is considerable cost associated with silt loading measurements; it is feasible to sample only a small portion of a roadway network. A new approach for measuring the concentration of suspendable PM 10 above road surfaces has been developed to obtain a more spatially representative estimate of a road's potential to emit dust. The Testing Re-entrained Aerosols Kinetic Emissions from Roads (TRAKER) system uses real-time aerosol sensors mounted on a vehicle to measure the concentration of dust suspended from the road while the vehicle is in motion. When coupled with a Global Positioning System (GPS) instrument, TRAKER can be used to efficiently survey the changes in suspendable particles due to varying road conditions over a large spatial domain. In a recent study on paved roads in Las Vegas, the TRAKER system was compared with collocated silt loading measurements. The TRAKER system was also used to survey the relative amounts of suspendable road dust on approximately 300 miles of paved roads. The system provides a unique perspective on road dust sources and their spatial distribution. Results of this study indicated that the difference of the PM 10 concentrations measured behind the tire and on the hood is exponentially related to vehicle speed. This was an interesting finding because current AP-42 road dust emissions estimation methods do not include vehicle speed as a factor in the emissions calculations. The experiment also demonstrated that the distribution of suspendable material on roadways is highly variable and that a large number of samples are needed to represent road dust emissions potential on an urban scale for a variety of road and activity conditions.

Visibility of road markings on wet road surfaces : a literature study.

NARCIS (Netherlands)

Schreuder, D.A.

1981-01-01

The English version of B 14153 is presented. Road markings, notably lane markers, are often only poorly visible when the road is wet. This is particularly a problem at night on unlit roads. A study is made of whether a solution for this problem can be found on the basis of the known, published

Armenia - Rural Road Rehabilitation

Data.gov (United States)

Millennium Challenge Corporation — The key research questions guiding our design of the RRRP evaluation are: • Did rehabilitating roads affect the quality of roads? • Did rehabilitating roads improve...

Effects of road salt on larval amphibian susceptibility to parasitism through behavior and immunocompetence.

Science.gov (United States)

Milotic, Dino; Milotic, Marin; Koprivnikar, Janet

2017-08-01

Large quantities of road salts are used for de-icing in temperate climates but often leach into aquatic ecosystems where they can cause harm to inhabitants, including reduced growth and survival. However, the implications of road salt exposure for aquatic animal susceptibility to pathogens and parasites have not yet been examined even though infectious diseases can significantly contribute to wildlife population declines. Through a field survey, we found a range of NaCl concentrations (50-560mg/L) in ponds known to contain larval amphibians, with lower levels found in sites close to gravel- rather than hard-surfaced roads. We then investigated how chronic exposure to environmentally-realistic levels of road salt (up to 1140mg/L) affected susceptibility to infection by trematode parasites (helminths) in larval stages of two amphibian species (Lithobates sylvaticus - wood frogs, and L. pipiens - northern leopard frogs) by considering effects on host anti-parasite behavior and white blood cell profiles. Wood frogs exposed to road salt had higher parasite loads, and also exhibited reduced anti-parasite behavior in these conditions. In contrast, infection intensity in northern leopard frogs had a non-monotonic response to road salts even though lymphocytes were only elevated at the highest concentration. Our results indicate the potential for chronic road salt exposure to affect larval amphibian susceptibility to pathogenic parasites through alterations of behavior and immunocompetence, with further studies needed at higher concentrations, as well as that of road salts on free-living parasite infectious stages. Copyright © 2017 Elsevier B.V. All rights reserved.

Sound recordings of road maintenance equipment on the Lincoln National Forest, New Mexico

Science.gov (United States)

D. K. Delaney; T. G. Grubb

2004-01-01

The purpose of this pilot study was to record, characterize, and quantify road maintenance activity in Mexican spotted owl (Strix occidentalis lucida) habitat to gauge potential sound level exposure for owls during road maintenance activities. We measured sound levels from three different types of road maintenance equipment (rock crusherlloader,...

Consistent haul road condition monitoring by means of vehicle response normalisation with Gaussian processes

CSIR Research Space (South Africa)

Heyns, T

2012-12-01

Full Text Available Suboptimal haul road management policies such as routine, periodic and urgent maintenance may result in unnecessary cost, both to roads and vehicles. A recent idea is to continually access haul road condition based on measured vehicle response...

Study on Construction Technology of Municipal Road and Bridge Concrete

Science.gov (United States)

Tang, Fuyong

2018-03-01

With the continuous development of social economy and the accelerating process of urbanization, municipal road and bridge projects have also shown a trend of rapid development. Municipal road and bridge work can fully reflect the economic and cultural development level of cities and is also an important symbol of urban development. As a basic material of construction, concrete is widely used in engineering construction. This article will analyze the municipal road and bridge concrete construction technology, put forward corresponding measures.

Neighbourhood walkability, road density and socio-economic status in Sydney, Australia.

Science.gov (United States)

Cowie, Christine T; Ding, Ding; Rolfe, Margaret I; Mayne, Darren J; Jalaludin, Bin; Bauman, Adrian; Morgan, Geoffrey G

2016-04-27

Planning and transport agencies play a vital role in influencing the design of townscapes, travel modes and travel behaviors, which in turn impact on the walkability of neighbourhoods and residents' physical activity opportunities. Optimising neighbourhood walkability is desirable in built environments, however, the population health benefits of walkability may be offset by increased exposure to traffic related air pollution. This paper describes the spatial distribution of neighbourhood walkability and weighted road density, a marker for traffic related air pollution, in Sydney, Australia. As exposure to air pollution is related to socio-economic status in some cities, this paper also examines the spatial distribution of weighted road density and walkability by socio-economic status (SES). We calculated walkability, weighted road density (as a measure of traffic related air pollution) and SES, using predefined and validated measures, for 5858 Sydney neighbourhoods, representing 3.6 million population. We overlaid tertiles of walkability and weighted road density to define "sweet-spots" (high walkability-low weighted road density), and "sour- spots" (low walkability-high weighted road density) neighbourhoods. We also examined the distribution of walkability and weighted road density by SES quintiles. Walkability and weighted road density showed a clear east-west gradient across the region. Our study found that only 4 % of Sydney's population lived in sweet-spot" neighbourhoods with high walkability and low weighted road density (desirable), and these tended to be located closer to the city centre. A greater proportion of neighbourhoods had health limiting attributes of high weighted road density or low walkability (about 20 % each), and over 5 % of the population lived in "sour-spot" neighbourhoods with low walkability and high weighted road density (least desirable). These neighbourhoods were more distant from the city centre and scattered more widely. There were

Poloidal magnetic field profile measurements on the microwave tokamak experiment using far-infrared polarimetry

International Nuclear Information System (INIS)

Rice, B.W.

1992-09-01

The measurement of plasma poloidal magnetic field (B) profiles in tokamaks with good temporal and spatial resolution has proven to be a difficult but important measurement. A large range of toroidal confinement phenomena is expected to depend sensitively on the radial variation of B including the tearing instability, sawtooth oscillations, disruptions, and transport. Experimental confirmation of theoretical models describing these phenomena has been hampered by the lack of detailed B measurements. A fifteen chord far-infrared (FIR) polarimeter has been developed to measure B in the Microwave Tokamak, Experiment (MTX). Polarimetry utilizes the well known Faraday rotation effect, which causes a rotation of the polarization of an FIR beam propagating in the poloidal plane. The rotation angle is proportional to the component of B parallel to the beam. A new technique for determining the Faraday rotation angle is introduced, based on phase measurements of a rotating polarization ellipse. This instrument has been used successfully to measure B profiles for a wide range of experiments on MTX. For ohmic discharges, measurements of the safety factor on axis give q 0 ∼ 0.75 during sawteeth and q 0 > 1 without sawteeth. Large perturbations to the polarimeter signals correlated with the sawtooth crash are observed during some discharges. Measurements in discharges with electron cyclotron heating (ECH) show a transition from a hollow to peaked J profile that is triggered by the ECH pulse. Current-ramp experiments were done to perturb the J profile from the nominal Spitzer conductivity profile. Profiles for initial current ramps and ramps starting from a stable equilibrium have been measured and are compared with a cylindrical diffusion model. Finally, the tearing mode stability equation is solved using measured J profiles. Stability predictions are in good agreement with the existence of oscillations observed on the magnetic loops

Ecological study of road traffic injuries in the eastern Mediterranean region: country economic level, road user category and gender perspectives.

Science.gov (United States)

Sengoelge, Mathilde; Laflamme, Lucie; El-Khatib, Ziad

2018-02-13

The Eastern Mediterranean region has the second highest number of road traffic injury mortality rates after the African region based on 2013 data, with road traffic injuries accounting for 27% of the total injury mortality in the region. Globally the number of road traffic deaths has plateaued despite an increase in motorization, but it is uncertain whether this applies to the Region. This study investigated the regional trends in both road traffic injury mortality and morbidity and examined country-based differences considering on income level, categories of road users, and gender distribution. Register-based ecological study linking data from Global Burden of Disease Study with the United Nations Statistics Division for population and World Bank definition for country income level. Road traffic injury mortality rates and disability-adjusted life years were compiled for all ages at country level in 1995, 2005, 2015 and combined for a regional average (n = 22) and a global average (n = 122). The data were stratified by country economic level, road user category and gender. Road traffic injury mortality rates in the Region were higher than the global average for all three reference years but suggest a downward trend. In 2015 mortality rates were more than twice as high in low and high income countries compared to global income averages and motor vehicle occupants had a 3-fold greater mortality than the global average. Severe injuries decreased by more than half for high/middle income countries but remained high for low income countries; three times higher for males than females. Despite a potential downward trend, inequalities in road traffic injury mortality and morbidity burden remain high in the Eastern Mediterranean region. Action needs to be intensified and targeted to implement and enforce safety measures that prevent and mitigate severe motor vehicle crashes in high income countries especially and invest in efforts to promote public, active transport

Measurement of ion profiles in TFTR neutral beamlines

International Nuclear Information System (INIS)

Kamperschroer, J.H.; Grisham, L.R.; Kugel, H.W.; O'Connor, T.E.; Stevenson, T.N.; von Halle, A.; Williams, M.D.

1992-02-01

A technique is described whereby the ion dumps inside the TFTR Neutral Beam Test Stand were used to measure thermal profiles of the full-, half-, and third-energy ions. 136 thermocouples were installed on the full-energy ion dump, allowing full beam contours. Additional linear arrays across the widths of the half- and third-energy ion dumps provided a measure of the shape, in the direction parallel to the grid rails, of the half- and third-energy ions, and, hence, of the molecular ions extracted from the source. As a result of these measurements it was found that the magnet was more weakly focusing, by a factor of two, than expected, explaining past overheating of the full-energy ion dump. Hollow profiles on the half- and third-energy ion dumps were observed, suggesting that extraction of D 2 + and D 3 + are primarily from the edge of the ion source. If extraction of half-energy ions is from the edge of the accelerator, a divergence parallel to the grid rails of 0.6 degrees ±0.1 degrees results. It is postulated that a nonuniform gas profile near the accelerator is the cause of the hollow partial-energy ion profiles; the pressure being depressed over the accelerator by particles passing through this highly transparent structure. Primary electrons reaching the accelerator produce nonuniform densities of D 2 + through the ionization of this across the full-energy dump was examined as a means of reducing the power density. By unbalancing the current in the two coils of the magnet, on a shot by shot basis, by up to 2:1 ratio, it was possible to move the centerline of the full-energy ion beam sideways by ∼12.5 cm. The adoption of such a technique, with a ramp of the coil imbalance from 2:1 to 1:2 over a beam pulse, could reduce the power density by a factor of ≥1.5

Modelling the impact of roads on regional population of Moor frogs (Rana arvalis)

DEFF Research Database (Denmark)

Pontoppidan, Maj-Britt

for decisions concerning road lay-out and mitigation measures. As model species was chosen the Moor frog (Rana arvalis). Populations of Moor frogs are assumed to follow a pattern of metapopulation dynamics, with colonisation, extinction and recolonisation of suitable habitat patches. Thus, road constructions...... to be constructed and analysed. The first scenario should be a map of the area as it is before the planned road construction (scenario 0). This analysis measures the ecological performance of the original landscape and is a reference against which other scenarios are to be compared. The second map (scenario 1......) should show the landscape as it is expected to be after the road constructions. In combination, the analyses of scenario 0 and scenario 1 make it possible to assess the effect of road construction on connectivity and population persistence. The analyses also constitute the basis for planning...

The influence of thermal biology on road mortality risk in snakes.

Science.gov (United States)

Mccardle, Logan D; Fontenot, Clifford L

2016-02-01

Road mortality is a significant threat to terrestrial vertebrates in many areas, and the novel thermal environment of black-topped roads may represent ecological traps for some species and demographic groups. We investigated the relationship between ambient temperature and on-road detection in a snake assemblage in southeastern Louisiana by comparing observations of live snakes on a black-topped road, across measurements of air temperature and road temperature on survey days. Analyses indicated on-road detection of snakes was significantly influenced by ambient temperature conditions for five snake species. Additionally, road temperatures, and the difference between air and road temperatures, were strong drivers of on-road snake detections. Permutation analysis methods revealed that significant temperature related group (species or sex) structure exists in occurrences of snakes on the roadway, and that road temperature was the strongest driver of species differences. We also compared how air and road temperatures affected occurrence on the road between sexes in the colubrid snakes Nerodia fasciata, Nerodia cyclopion, Thamnophis proximus, and Pantherophis obsoletus. Males and females of the viviparous species N. fasciata, N. cyclopion, and T. proximus diverged significantly in temperature preferences, with females found under warmer conditions, while males and females of the oviparous species P. obsoletus did not. Road temperature was also the strongest driver of differences between sexes. Our results indicate that black-topped roads are an ecological trap that is heavily influenced by sex, reproductive condition, and species specific thermoregulatory requirements, particularly for viviparous species. Copyright © 2015 Elsevier Ltd. All rights reserved.

Linear chirped slope profile for spatial calibration in slope measuring deflectometry

Energy Technology Data Exchange (ETDEWEB)

Siewert, F., E-mail: frank.siewert@helmholtz-berlin.de; Zeschke, T. [Helmholtz Zentrum Berlin für Materialien und Energie, Institut für Nanometer Optik und Technologie, Albert-Einstein-Str. 15, 12489 Berlin (Germany); Arnold, T.; Paetzelt, H. [Leibnitz Institut für Oberflächen Modifizierung Leipzig e.V., IOM, Permoserstr. 15, 04318 Leipzig (Germany); Yashchuk, V. V. [Lawerence Berkeley National Laboratory, Advanced Light Source, 1 Cyclotron Road, Berkeley, California 94720 (United States)

2016-05-15

Slope measuring deflectometry is commonly used by the X-ray optics community to measure the long-spatial-wavelength surface figure error of optical components dedicated to guide and focus X-rays under grazing incidence condition at synchrotron and free electron laser beamlines. The best performing instruments of this kind are capable of absolute accuracy on the level of 30-50 nrad. However, the exact bandwidth of the measurements, determined at the higher spatial frequencies by the instrument’s spatial resolution, or more generally by the instrument’s modulation transfer function (MTF) is hard to determine. An MTF calibration method based on application of a test surface with a one-dimensional (1D) chirped height profile of constant amplitude was suggested in the past. In this work, we propose a new approach to designing the test surfaces with a 2D-chirped topography, specially optimized for MTF characterization of slope measuring instruments. The design of the developed MTF test samples based on the proposed linear chirped slope profiles (LCSPs) is free of the major drawback of the 1D chirped height profiles, where in the slope domain, the amplitude strongly increases with the local spatial frequency of the profile. We provide the details of fabrication of the LCSP samples. The results of first application of the developed test samples to measure the spatial resolution of the BESSY-NOM at different experimental arrangements are also presented and discussed.

Complete methodology on generating realistic wind speed profiles based on measurements

DEFF Research Database (Denmark)

Gavriluta, Catalin; Spataru, Sergiu; Mosincat, Ioan

2012-01-01

, wind modelling for medium and large time scales is poorly treated in the present literature. This paper presents methods for generating realistic wind speed profiles based on real measurements. The wind speed profile is divided in a low- frequency component (describing long term variations...

Concentration levels and source apportionment of ultrafine particles in road microenvironments

Science.gov (United States)

Argyropoulos, G.; Samara, C.; Voutsa, D.; Kouras, A.; Manoli, E.; Voliotis, A.; Tsakis, A.; Chasapidis, L.; Konstandopoulos, A.; Eleftheriadis, K.

2016-03-01

A mobile laboratory unit (MOBILAB) with on-board instrumentation (Scanning Mobility Particle Sizer, SMPS; Ambient NOx analyzer) was used to measure size-resolved particle number concentrations (PNCs) of quasi-ultrafine particles (UFPs, 9-372 nm), along with NOx, in road microenvironments. On-road measurements were carried out in and around a large Greek urban agglomeration, the Thessaloniki Metropolitan Area (TMA). Two 2-week measurement campaigns were conducted during the warm period of 2011 and the cold period of 2012. During each sampling campaign, MOBILAB was driven through a 5-day inner-city route and a second 5-day external route covering in total a wide range of districts (urban, urban background, industrial and residential), and road types (major and minor urban roads, freeways, arterial and interurban roads). All routes were conducted during working days, in morning and in afternoon hours under real-world traffic conditions. Spatial classification of MOBILAB measurements involved the assignment of measurement points to location bins defined by the aspect ratio of adjacent urban street canyons (USCs). Source apportionment was further carried out, by applying Positive Matrix Factorization (PMF) to particle size distribution data. Apportioned PMF factors were interpreted, by employing a two-step methodology, which involved (a) statistical association of PMF factor contributions with 12 h air-mass back-trajectories ending at the TMA during MOBILAB measurements, and (b) Multiple Linear Regression (MLR) using PMF factor contributions as the dependent variables, while relative humidity, solar radiation flux, and vehicle speed were used as the independent variables. The applied data analysis showed that low-speed cruise and high-load engine operation modes are the two dominant sources of UFPs in most of the road microenvironments in the TMA, with significant contributions from background photochemical processes during the warm period, explaining the reversed

Improving the surface metrology accuracy of optical profilers by using multiple measurements

Science.gov (United States)

Xu, Xudong; Huang, Qiushi; Shen, Zhengxiang; Wang, Zhanshan

2016-10-01

The performance of high-resolution optical systems is affected by small angle scattering at the mid-spatial-frequency irregularities of the optical surface. Characterizing these irregularities is, therefore, important. However, surface measurements obtained with optical profilers are influenced by additive white noise, as indicated by the heavy-tail effect observable on their power spectral density (PSD). A multiple-measurement method is used to reduce the effects of white noise by averaging individual measurements. The intensity of white noise is determined using a model based on the theoretical PSD of fractal surface measurements with additive white noise. The intensity of white noise decreases as the number of times of multiple measurements increases. Using multiple measurements also increases the highest observed spatial frequency; this increase is derived and calculated. Additionally, the accuracy obtained using multiple measurements is carefully studied, with the analysis of both the residual reference error after calibration, and the random errors appearing in the range of measured spatial frequencies. The resulting insights on the effects of white noise in optical profiler measurements and the methods to mitigate them may prove invaluable to improve the quality of surface metrology with optical profilers.

In vivo measurement of urethral dose profiles

International Nuclear Information System (INIS)

Toye, W.C.; Royal Melbourne Institute of Technology,; Duchesne, G.M.; Das, K.R.; Cee, A.; Mameghan, H.; Johnston, P.N.

2001-01-01

definition and translation variation, or gland edema) are not introduced as the TLD train must lay in the centre of the urethra. Typically, agreement between measured and predicted (localised by the position of brass spacers) urethral doses was ± 3%. On one occasion, after review of the measured profile, a treatment plan was subsequently altered for the remaining 3 treatment fractions. The urethral cavity provided an ideal location from which TLD in vivo measurements were made during HDR brachytherapy to the prostate. A method for obtaining a database of measured urethral dose profiles using routine in vivo TLD dosimetry is described. The in vivo measurements were in good agreement with profiles predicted by the dose planning algorithm. Copyright (2001) Australasian College of Physical Scientists and Engineers in Medicine

A comparison on radar range profiles between in-flight measurements and RCS-predictions

NARCIS (Netherlands)

Heiden, R. van der; Ewijk, L.J. van; Groen, F.C.A.

1998-01-01

The validation of Radar Cross Section (RCS) prediction techniques against real measurements is crucial to acquire confidence in predictions when measurements are nut available. In this paper we present the results of a comparison on one-dimensional signatures, i.e. radar range profiles. The profiles

Road safety analysis on Achmad Yani frontage road Surabaya

Science.gov (United States)

Machsus; Prayogo, I.; Chomaedhi; Hayati, D. W.; Utanaka, A.

2017-11-01

This research discusses road safety analysis on the operation of frontage road on the west side of Achmad Yani Road Surabaya. This research began by conducting survey on secondary data of traffic accidents. In addition, primary data survey was conducted to obtain traffic data, geometric road data, and other supporting data at the study site along the west side frontage of Ahmad Yani Road Surabaya. Devices used in this research include camera, handy cam, speed gun, counters of vehicles, rolling meter, computer and others. In outline, the stages to conduct this research are divided into 4 stages, namely 1.the preparation stage, 2.data collection and processing, 3. analysis and discussion, and 4. conclusion. The results of this study showed that the accident characteristics of the frontage road are (i) 3 accidents occured per month, (ii) motorcycles was accounted for the largest proportion of accidents which amounted to 74.6 percent, (iii) there were 3 accident victims per month, and (iv) material losses per month worths 1.2 million. The accident rate in 2016 was 0.04 crashes per one million vehicle travels per kilometer, while during 2 months in 2017 it was 0.15 accidents per one million vehicle travels per kilometer. Black spot area of accident is located on Sta 2 + 800 to 2 + 900 which is in front of Graha Pena building and DBL Arena. The high rate of accidents is influenced by the speed of the vehicle which 85 percentile exceeds the speed limit of 40km per hour.

COLUROUTE : a mobile gonio-reflectometer to characterize the road surface photometry

OpenAIRE

MUZET, Valérie; PAUMIER, Jean Luc; GUILLARD, Yannick

2008-01-01

Designing a lighting installation involves accounting for site-specific geometric parameters and photometric characteristics of both the light sources and the road surface. The standard tool for characterizing road surface photometry is the reduced luminance coefficient table (or R-table), as defined in the 70's by the CIE. However, recent studies have shown that these tables are no longer representative. In this context, measuring road photometry is necessary for optimizing a lighting ins...

Edge density profile measurements by X-mode reflectometry on Tore Supra

International Nuclear Information System (INIS)

Clairet, F.; Bottereau, C.; Chareau, J.M.; Paume, M.; Sabot, R.

2000-10-01

A broadband reflectometer operating in the frequency range 50-75 GHz has been developed on Tore Supra to measure electron density profiles at the edge. The system uses extraordinary mode polarization and performs routine measurements in 20 μs with a heterodyne detection to ensure a high dynamic range sensitivity. It allows separate phase and amplitude information of the signal. The density profiles are fully automatically calculated from the raw phase. The initialization is done with an automatic detection of the first cut-off from the amplitude of the reflected signal with accuracy up to ±0.5 cm. The profiles are now part of the public database of Tore Supra (TS) and can provide details of density structures better than the centimeter range. High reliability of the measurements for various plasma conditions make this diagnostic an ideal tool to study specific edge plasma physics with given examples on detached plasma behaviour and RF antenna-plasma coupling processes. It also is shown how the presence of suprathermal electrons may perturb the measurements. (authors)

Measurement of CO2 emissions from road freight transport: A review of UK experience

International Nuclear Information System (INIS)

McKinnon, A.C.; Piecyk, M.I.

2009-01-01

It is possible to estimate CO 2 emissions from road freight transport in different ways, depending on the definition of trucking activity, the degree of reliance on survey, vehicle test-cycle and traffic count data and the geographical scope of the calculation. The emergence of differing road freight-related CO 2 estimates from official sources and revisions to statistical series can frustrate the policy-making process and erode the confidence of industry stakeholders in the validity of the figures. Using UK data, this paper examines the various methods of carbon auditing road freight transport at the national level and compares the results both for a single year (2006) and over a time period. It highlights a series of statistical anomalies and approximations and tries to explain discrepancies that have arisen in the UK data sets. A concluding section considers the general lessons that can be learned from the recent UK experience in this field.

Objective measurement of inhaler inhalation flow profile using acoustic methods

Energy Technology Data Exchange (ETDEWEB)

Lacalle, H.; Taylor, T.E.; Marco, S.; Reilly, R.B.

2016-07-01

Patients with asthma and chronic obstructive pulmonary diseases (COPD) are mostly treated with inhalers that deliver medication directly to their airways. Drug delivery from dry powder inhalers (DPIs) is very much reliant on the inhalation manoeuvre, specifically the peak inspiratory flow rate (PIFR), inspiratory capacity (IC) and inhalation rise time (IRT) of the inhalation. It has been widely reported that patients may not follow correct inhalation technique while using their inhaler. In this study, a novel acoustic method is proposed to accurately estimate inhalation flow profile using only one inhalation recording for calibration. An Ellipta DPI was placed inside an airtight container with a spirometer connected in order to measure inhalation flow parameters. An acoustic recording device (Inhaler Compliance Assessment (INCA)) was also attached to the DPI. Inhalation audio and flow signals were recorded simultaneously. The data were collected from 20 healthy subjects while performing inhaler inhalations at a range of inspiratory flow rates. A power law regression model was computed to obtain the relationship between the acoustic envelope of the inhalation and flow profile of each recording. Each model was tested on the remaining audio signals to estimate flow profile. The average estimation error was found to be 10.5±0.3% for estimating flow profile from audio signals. Inhalation flow profile parameters (PIFR, IC and IRT) could then be measured from the estimated flow profile with high accuracy giving information on user inhalation technique. This method may assist in improving patient inhaler adherence and overall disease control. (Author)

Road Accidents and Road Fatalities in Denmark from 1968 to 2004

DEFF Research Database (Denmark)

Orozova-Bekkevold, Ivanka; Hels, Tove; Bernhoft, Inger Marie

2008-01-01

The purpose of this article is to describe the road accidents and road fatalities in Denmark in the period 1968-2004. Only accidents registered by the police were used. Crude and gender & age specific fatality rates (counts per 1,000,000 inhabitants) were estimated for all road users...... and for bicyclists. The accident and fatality rates have decreased by around 70% from 1968 to 2004, while the motorisation rate has increased by approximately 90%. The sharpest decrease in the fatality rate was observed among the youngest (below 18 years old) and the older (above 64) road users. Gender related...... and actions targeted to improve road safety have indeed led to a significant reduction in injury accidents and fatalities. Further research and more detailed data, especially on traffic volume and individual exposure are necessary in order to investigate properly a causal relation between the number...

Moving gantry method for electron beam dose profile measurement at extended source-to-surface distances.

Science.gov (United States)

Fekete, Gábor; Fodor, Emese; Pesznyák, Csilla

2015-03-08

A novel method has been put forward for very large electron beam profile measurement. With this method, absorbed dose profiles can be measured at any depth in a solid phantom for total skin electron therapy. Electron beam dose profiles were collected with two different methods. Profile measurements were performed at 0.2 and 1.2 cm depths with a parallel plate and a thimble chamber, respectively. 108cm × 108 cm and 45 cm × 45 cm projected size electron beams were scanned by vertically moving phantom and detector at 300 cm source-to-surface distance with 90° and 270° gantry angles. The profiles collected this way were used as reference. Afterwards, the phantom was fixed on the central axis and the gantry was rotated with certain angular steps. After applying correction for the different source-to-detector distances and incidence of angle, the profiles measured in the two different setups were compared. Correction formalism has been developed. The agreement between the cross profiles taken at the depth of maximum dose with the 'classical' scanning and with the new moving gantry method was better than 0.5 % in the measuring range from zero to 71.9 cm. Inverse square and attenuation corrections had to be applied. The profiles measured with the parallel plate chamber agree better than 1%, except for the penumbra region, where the maximum difference is 1.5%. With the moving gantry method, very large electron field profiles can be measured at any depth in a solid phantom with high accuracy and reproducibility and with much less time per step. No special instrumentation is needed. The method can be used for commissioning of very large electron beams for computer-assisted treatment planning, for designing beam modifiers to improve dose uniformity, and for verification of computed dose profiles.

Determination of road dust loadings and chemical characteristics using resuspension.

Science.gov (United States)

Chen, Jianhua; Wang, Wei; Liu, Hongjie; Ren, Lihong

2012-03-01

The contribution of fugitive dust from traffic to air pollution can no longer be ignored in China. In order to obtain the road dust loadings and to understand the chemical characteristics of PM(10) and PM(2.5) from typical road dust, different paved roads in eight districts of Beijing were selected for dust collection during the four seasons of 2005. Ninety-eight samples from 28 roads were obtained. The samples were resuspended using equipment assembled to simulate the rising process of road dust caused by the wind or wheels in order to obtain the PM(10) and PM(2.5) filter samples. The average road dust loading was 3.82 g m(-2), with the highest of 24.22 g m(-2) being in Hutongs in the rural-urban continuum during winter. The road dust loadings on higher-grade roads were lower than those on lower-grade roads. Attention should be paid to the pollution in the rural-urban continuum areas. The sums of element abundances measured were 16.17% and 18.50% for PM(10) and PM(2.5) in road dust. The average abundances of OC and EC in PM(10) and PM(2.5) in road dust were 11.52%, 2.01% and 12.50%, 2.06%, respectively. The abundance of elements, water-soluble ions, and OC, EC in PM(10) and PM(2.5) resuspended from road dust did not change greatly with seasons and road types. The soil dust, construction dust, dust emitted from burning coal, vehicle exhaust, and deposition of particles in the air were the main sources of road dust in Beijing. Affected by the application of snow-melting agents in Beijing during winter, the amount of Cl( - ) and Na( + ) was much higher during that time than in the other seasons. This will have a certain influence on roads, bridges, vegetations, and groundwater.

A Lightweight Radio Propagation Model for Vehicular Communication in Road Tunnels.

Directory of Open Access Journals (Sweden)

Muhammad Ahsan Qureshi

Full Text Available Radio propagation models (RPMs are generally employed in Vehicular Ad Hoc Networks (VANETs to predict path loss in multiple operating environments (e.g. modern road infrastructure such as flyovers, underpasses and road tunnels. For example, different RPMs have been developed to predict propagation behaviour in road tunnels. However, most existing RPMs for road tunnels are computationally complex and are based on field measurements in frequency band not suitable for VANET deployment. Furthermore, in tunnel applications, consequences of moving radio obstacles, such as large buses and delivery trucks, are generally not considered in existing RPMs. This paper proposes a computationally inexpensive RPM with minimal set of parameters to predict path loss in an acceptable range for road tunnels. The proposed RPM utilizes geometric properties of the tunnel, such as height and width along with the distance between sender and receiver, to predict the path loss. The proposed RPM also considers the additional attenuation caused by the moving radio obstacles in road tunnels, while requiring a negligible overhead in terms of computational complexity. To demonstrate the utility of our proposed RPM, we conduct a comparative summary and evaluate its performance. Specifically, an extensive data gathering campaign is carried out in order to evaluate the proposed RPM. The field measurements use the 5 GHz frequency band, which is suitable for vehicular communication. The results demonstrate that a close match exists between the predicted values and measured values of path loss. In particular, an average accuracy of 94% is found with R2 = 0.86.

Epidemiology of Deaths from Road Traffic Accidents in Nigeria: A ...

African Journals Online (AJOL)

The purpose of this study is to examine the epidemiology of deaths from Road Traffic Accidents (RTAs) in Nigeria using Lagos State as a baseline study and to suggest preventive and corrective safety measures towards reducing the traffic accidents in the study area. The reported number of deaths from road traffic accidents ...

Use of fatal real-life crashes to analyze a safe road transport system model, including the road user, the vehicle, and the road.

Science.gov (United States)

Stigson, Helena; Krafft, Maria; Tingvall, Claes

2008-10-01

To evaluate if the Swedish Road Administration (SRA) model for a safe road transport system, which includes the interaction between the road user, the vehicle, and the road, could be used to classify fatal car crashes according to some safety indicators. Also, to present a development of the model to better identify system weakness. Real-life crashes with a fatal outcome were classified according to the vehicle's safety rating by Euro NCAP (European Road Assessment Programme) and fitment of ESC (Electronic Stability Control). For each crash, the road was also classified according to EuroRAP (European Road Assessment Programme) criteria, and human behavior in terms of speeding, seat belt use, and driving under the influence of alcohol. Each crash was compared with the model criteria, to identify components that might have contributed to fatal outcome. All fatal crashes where a car occupant was killed that occurred in Sweden during 2004 were included: in all, 215 crashes with 248 fatalities. The data were collected from the in-depth fatal crash data of the Swedish Road Administration (SRA). It was possible to classify 93% of the fatal car crashes according to the SRA model. A number of shortcomings in the criteria were identified since the model did not address rear-end or animal collisions or collisions with stationary/parked vehicles or trailers (18 out of 248 cases). Using the further developed model, it was possible to identify that most of the crashes occurred when two or all three components interacted (in 85 of the total 230 cases). Noncompliance with safety criteria for the road user, the vehicle, and the road led to fatal outcome in 43, 27, and 75 cases, respectively. The SRA model was found to be useful for classifying fatal crashes but needs to be further developed to identify how the components interact and thereby identify weaknesses in the road traffic system. This developed model might be a tool to systematically identify which of the components are

Rehabilitation of a secondary network of forest traffic infrastructure (skid roads - skid trails

Directory of Open Access Journals (Sweden)

Bajrić Muhamed

2015-01-01

Full Text Available Forest transport infrastructure is the key segment of rational forest resource management. One of its constituent and inseparable segments are skid roads and skid trails whose network density significantly exceeds the primary network, i.e. truck roads. Skid road -skid trail network density in high economic forests of FB&H is most often between 40 and 100 m/ha. Simplified way of construction, non-existence of road construction, objects for surface water drainage as well as significant longitudinal inclination (up to 50% in which they are constructed, makes them subject to erosion processes. The lack of rehabilitation measures on skid roads - skid trails causes significant damages in post-exploitation period, and very often to the extent that the ones in the following exploitation round are unusable for skidding. Utilization of skid roads - skid trails damaged by erosion processes for forest operations often represents a significant expense. This paper considers rehabilitation measures efficient from the point of remedying erosion processes, and at the same time, acceptable from the point of financial expenditure for forest operations.

ROAD TRAFFIC ESTIMATION USING BLUETOOTH SENSORS

Directory of Open Access Journals (Sweden)

Monika N. BUGDOL

2017-09-01

Full Text Available The Bluetooth standard is a low-cost, very popular communication protocol offering a wide range of applications in many fields. In this paper, a novel system for road traffic estimation using Bluetooth sensors has been presented. The system consists of three main modules: filtration, statistical analysis of historical, and traffic estimation and prediction. The filtration module is responsible for the classification of road users and detecting measurements that should be removed. Traffic estimation has been performed on the basis of the data collected by Bluetooth measuring devices and information on external conditions (e.g., temperature, all of which have been gathered in the city of Bielsko-Biala (Poland. The obtained results are very promising. The smallest average relative error between the number of cars estimated by the model and the actual traffic was less than 10%.

Validation of the "Security Needs Assessment Profile" for measuring the profiles of security needs of Chinese forensic psychiatric inpatients.

Science.gov (United States)

Siu, B W M; Au-Yeung, C C Y; Chan, A W L; Chan, L S Y; Yuen, K K; Leung, H W; Yan, C K; Ng, K K; Lai, A C H; Davies, S; Collins, M

Mapping forensic psychiatric services with the security needs of patients is a salient step in service planning, audit and review. A valid and reliable instrument for measuring the security needs of Chinese forensic psychiatric inpatients was not yet available. This study aimed to develop and validate the Chinese version of the Security Needs Assessment Profile for measuring the profiles of security needs of Chinese forensic psychiatric inpatients. The Security Needs Assessment Profile by Davis was translated into Chinese. Its face validity, content validity, construct validity and internal consistency reliability were assessed by measuring the security needs of 98 Chinese forensic psychiatric inpatients. Principal factor analysis for construct validity provided a six-factor security needs model explaining 68.7% of the variance. Based on the Cronbach's alpha coefficient, the internal consistency reliability was rated as acceptable for procedural security (0.73), and fair for both physical security (0.62) and relational security (0.58). A significant sex difference (p=0.002) in total security score was found. The Chinese version of the Security Needs Assessment Profile is a valid and reliable instrument for assessing the security needs of Chinese forensic psychiatric inpatients. Copyright © 2017 Elsevier Ltd. All rights reserved.

An automated, noncontact laser profile meter for measuring soil roughness in situ

International Nuclear Information System (INIS)

Bertuzzi, P.; Caussignac, J.M.; Stengel, P.; Morel, G.; Lorendeau, J.Y.; Pelloux, G.

1990-01-01

This paper describes a new optical technique for measuring in situ soil surface roughness profiles using a laser profile meter. The described method uses a low-power HeNe (helium-neon) laser as a laser source and a matrix-array detector, as the laser image. The matrix-array detector gives a defect-of-focus laser image of the soil. Soil elevation is measured by projecting a laser beam normally onto the soil surface and measuring the ratio (Ir/It) on the matrix-array detector between the referenced intensity of the return Laser beam (Ir), measured by the central cell of the detector and the total intensity (It), measured by all the cells of the detector. The measured profile leads to 1001 sampled values (volt, range 0 to 10 V) of the surface height profile, at a constant increment of 0.002 m, registered automatically on a microcomputer. A calibration is made in the laboratory in order to convert the electrical measurements into elevation data. The method is universal and can be adapted to different scales of soil surface roughness. Changing the scale is done by changing the lens. Tests were carried out to improve this method for field use and to compare this technique with a method of reference. This technique is considerably quicker and causes no disturbance to the soil. The accuracy on height measurement depends on the choice of the lens. The small focal lens is convenient for smooth soil surfaces. The accuracy on height measurement is less than 0.75 mm. The wide focal lens is convenient for rough soil surfaces. The accuracy on height measurement is estimated at about 1.0 to 1.5 mm

Habitat or matrix: which is more relevant to predict road-kill of vertebrates?

Science.gov (United States)

Bueno, C; Sousa, C O M; Freitas, S R

2015-11-01

We believe that in tropics we need a community approach to evaluate road impacts on wildlife, and thus, suggest mitigation measures for groups of species instead a focal-species approach. Understanding which landscape characteristics indicate road-kill events may also provide models that can be applied in other regions. We intend to evaluate if habitat or matrix is more relevant to predict road-kill events for a group of species. Our hypothesis is: more permeable matrix is the most relevant factor to explain road-kill events. To test this hypothesis, we chose vertebrates as the studied assemblage and a highway crossing in an Atlantic Forest region in southeastern Brazil as the study site. Logistic regression models were designed using presence/absence of road-kill events as dependent variables and landscape characteristics as independent variables, which were selected by Akaike's Information Criterion. We considered a set of candidate models containing four types of simple regression models: Habitat effect model; Matrix types effect models; Highway effect model; and, Reference models (intercept and buffer distance). Almost three hundred road-kills and 70 species were recorded. River proximity and herbaceous vegetation cover, both matrix effect models, were associated to most road-killed vertebrate groups. Matrix was more relevant than habitat to predict road-kill of vertebrates. The association between river proximity and road-kill indicates that rivers may be a preferential route for most species. We discuss multi-species mitigation measures and implications to movement ecology and conservation strategies.

Overload road damage model

CSIR Research Space (South Africa)

Roux, MP

2005-03-01

Full Text Available Not only do overloaded vehicles pose an increased safety risk on the road (reduced stability and braking efficiency etc.), but they also accelerate the rate of deterioration of the road network and increase road maintenance costs, which in turn...

Benchmarking road safety performance: Identifying a meaningful reference (best-in-class).

Science.gov (United States)

Chen, Faan; Wu, Jiaorong; Chen, Xiaohong; Wang, Jianjun; Wang, Di

2016-01-01

For road safety improvement, comparing and benchmarking performance are widely advocated as the emerging and preferred approaches. However, there is currently no universally agreed upon approach for the process of road safety benchmarking, and performing the practice successfully is by no means easy. This is especially true for the two core activities of which: (1) developing a set of road safety performance indicators (SPIs) and combining them into a composite index; and (2) identifying a meaningful reference (best-in-class), one which has already obtained outstanding road safety practices. To this end, a scientific technique that can combine the multi-dimensional safety performance indicators (SPIs) into an overall index, and subsequently can identify the 'best-in-class' is urgently required. In this paper, the Entropy-embedded RSR (Rank-sum ratio), an innovative, scientific and systematic methodology is investigated with the aim of conducting the above two core tasks in an integrative and concise procedure, more specifically in a 'one-stop' way. Using a combination of results from other methods (e.g. the SUNflower approach) and other measures (e.g. Human Development Index) as a relevant reference, a given set of European countries are robustly ranked and grouped into several classes based on the composite Road Safety Index. Within each class the 'best-in-class' is then identified. By benchmarking road safety performance, the results serve to promote best practice, encourage the adoption of successful road safety strategies and measures and, more importantly, inspire the kind of political leadership needed to create a road transport system that maximizes safety. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Epidemiology of Fatal road traffic Collisions in Trinidad and Tobago, West Indies (2000–2011

Directory of Open Access Journals (Sweden)

Chavin D. Gopaul

2016-11-01

Full Text Available Summary of what was known• Few studies on road traffic collisions conducted in Latin American and the Caribbean region• Increasing car ownership within the region• Lack of seatbelt usage in Trinidad• Most accidents are associated with alcohol usage• High mortality among pedestriansSummary of what this study adds• Most collisions occur at night• Most collisions occur at weekends• Collisions are evenly distributed throughout the year• More males than females die in fatal collisions• The most productive age group (15–44 is affected the most• More drivers than pedestrians are affected• Reflects the pattern of developed rather than developing countries with respect to time of day for RTCs Background: The purpose of the study is to determine the epidemiology of road traffic collisions (RTCs in Trinidad and Tobago by characterizing RTCs in terms of number of collisions, fatalities, victim profiles, and locations for the purpose of informing accident prevention programs. Previous studies of RTCs in Trinidad and Tobago were primarily concerned with patterns of drivers use of seat belts, road collisions as a cause of mortality in young men, and the economic burden of road collisions. Attempts were made to model road fatalities, but limited epidemiological data meant that it was difficult to determine trends or develop models. Methods: This study determined the epidemiology of RTCs in Trinidad and Tobago over the period 2000–2011using data collected by the Trinidad and Tobago Road Traffic Branch of the Police Service and secondary data from the Central Statistical Office. Data were analyzed using Excel, SPSS, and R statistical packages. Results: Fatalities were greater among men (80% than among women (20% and were highest on two major freeways in Trinidad [the Churchill–Roosevelt Highway and the Sir Solomon Hochoy Highway]. Most collisions occurred during the night among individuals between the ages of

The impact of road improvements on road safety and related characteristics

OpenAIRE

Francis John Gichaga

2017-01-01

This paper presents the historical and cultural background relating to road improvement and road safety characteristics in Kenya, a developing country in East Africa. Some who come from low-developed areas of developing countries often take time to comprehend the modern transportation infrastructure, especially roads, and have difficulty assimilating and customizing the same to their culturally tailored modes. This paper discusses two case studies: one on the socio-economic impact followin...

Mainstreaming road safety in the regional integration of the East ...

African Journals Online (AJOL)

The East African Community (EAC) comprising of five states: Burundi, Kenya, Rwanda, Tanzania and Uganda bear a disproportionate burden of the global public health burden for road traffic injuries (RTIs). In response to this, each state has devised its own road safety measures, but not at the EAC level. This paper aims to ...

Characteristics of public roads operation

OpenAIRE

Pryimak, V.; Kyiashko, I.

2009-01-01

Characteristics of public roads operation have been considered and factors influencing TEC of public roads that go via urban areas have been determined. There have been revealed contradictions in the normative-legal base concerning maintenance of public roads and municipal roads that merge into them.

Techniques for Efficient Tracking of Road-Network-Based Moving Objects

DEFF Research Database (Denmark)

Civilis, Alminas; Jensen, Christian Søndergaard; Saltenis, Simonas

With the continued advances in wireless communications, geo-positioning, and consumer electronics, an infrastructure is emerging that enables location-based services that rely on the tracking of the continuously changing positions of entire populations of service users, termed moving objects....... The main issue considered is how to represent the location of a moving object in a database so that tracking can be done with as few updates as possible. The paper proposes to use the road network within which the objects are assumed to move for predicting their future positions. The paper presents...... algorithms that modify an initial road-network representation, so that it works better as a basis for predicting an object's position; it proposes to use known movement patterns of the object, in the form of routes; and it proposes to use acceleration profiles together with the routes. Using real GPS...

Techniques for efficient road-network-based tracking of moving objects

DEFF Research Database (Denmark)