Measurement of new operational quantities with radiation protection instruments designed for working area monitoring and for individual monitoring

International Nuclear Information System (INIS)

Prigent, R.; Chary, J.; Chemtob, M.

1992-01-01

The ICRP recommended a dose limitation system based on numerical evaluation of the dose equivalent to organs or tissues, H T , which are used to calculate the effective dose, H E , by weighting. The ICRU proposed new operational quantities accessible to measurement which are conservative with respect to these recommendations. The objective of this paper is to recall briefly the basic recommendations and to find out if radiation protection instruments presently used calibrated in terms of the previous quantities are capable to measure these new quantities. A dozen of practical cases are presented. (author)

Quantities for environmental monitoring

International Nuclear Information System (INIS)

1989-01-01

It is recommended that if measurements are made with the objective of monitor radiation levels in the environment to elucidate long-term changes in these levels, then air kerma should be used. If the objective is to give an indication that levels from man-made sources are acceptable within specified limits for the exposure of people, then ambient dose equivalent should be used. It should be noted that radiation risks to individuals are best expressed by the quantity effective dose equivalent. If this latter quantity is to be accurately assessed, it may be necessary to obtain details of the quality of the environmental radiation that cannot be described adequately by simple measurements of either air kerma or ambient dose equivalent. If the above objectives pertain, the measurements should record both air kerma and ambient dose equivalent. If neutrons are measured in the environment then ambient dose equivalent is the appropriate quantity for both the above objectives. (author)

Concept of ICRU's operational quantity and its application

International Nuclear Information System (INIS)

Murakami, Hiroyuki

1995-01-01

The operational quantity which was introduced in the ICRU report 39 published in 1985 was shocking rather than fresh for the author. The report was translated into Japanese, but at the beginning, the contents were not able to be understood. Thereafter, the measurement of ICRU sphere dose equivalent was introduced in a national law. But it is feared that the understanding of this operational quantity is limited to specialist level, and is not by men of practical works. The meaning of ''operational'' must be that workers measure and obtain dose on the spot for the radiation protection for themselves. The principles used when ICRU considered the new practical measured quantity are shown. In the definition of operational quantity in area monitoring, two concepts of expanded and aligned connect real measurement with the operational quantity. The problems of measuring individual dose equivalent are discussed. As to the reality of applying the operational quantity, the fundamentals of the calibration of measuring instruments, the investigation of the operational quantity in relation to measuring instruments and measurement mode, and the relation of area monitoring and individual monitoring are described. (K.I.)

Uncertainties in the measured quantities of water leaving waste Tank 241-C-106 via the ventilation system

Energy Technology Data Exchange (ETDEWEB)

Minteer, D.J.

1995-01-23

The purpose of this analysis is to estimate the uncertainty in the measured quantity of water which typically leaves Tank 241-C-106 via the ventilation system each month. Such measurements are essential for heat removal estimation and tank liquid level verification purposes. The uncertainty associated with the current, infrequent, manual method of measurement (involves various psychrometric and pressure measurements) is suspected to be unreasonably high. Thus, the possible reduction of this uncertainty using a continuous, automated method of measurement will also be estimated. There are three major conclusions as a result of this analysis: (1) the uncertainties associated with the current (infrequent, manual) method of measuring the water which typically leaves Tank 241-C-106 per month via the ventilation system are indeed quite high (80% to 120%); (2) given the current psychrometric and pressure measurement methods and any tank which loses considerable moisture through active ventilation, such as Tank 241-C-106, significant quantities of liquid can actually leak from the tank before a leak can be positively identified via liquid level measurement; (3) using improved (continuous, automated) methods of taking the psychrometric and pressure measurements, the uncertainty in the measured quantity of water leaving Tank 241-C-106 via the ventilation system can be reduced by approximately an order of magnitude.

Uncertainties in the measured quantities of water leaving waste Tank 241-C-106 via the ventilation system

International Nuclear Information System (INIS)

Minteer, D.J.

1995-01-01

The purpose of this analysis is to estimate the uncertainty in the measured quantity of water which typically leaves Tank 241-C-106 via the ventilation system each month. Such measurements are essential for heat removal estimation and tank liquid level verification purposes. The uncertainty associated with the current, infrequent, manual method of measurement (involves various psychrometric and pressure measurements) is suspected to be unreasonably high. Thus, the possible reduction of this uncertainty using a continuous, automated method of measurement will also be estimated. There are three major conclusions as a result of this analysis: (1) the uncertainties associated with the current (infrequent, manual) method of measuring the water which typically leaves Tank 241-C-106 per month via the ventilation system are indeed quite high (80% to 120%); (2) given the current psychrometric and pressure measurement methods and any tank which loses considerable moisture through active ventilation, such as Tank 241-C-106, significant quantities of liquid can actually leak from the tank before a leak can be positively identified via liquid level measurement; (3) using improved (continuous, automated) methods of taking the psychrometric and pressure measurements, the uncertainty in the measured quantity of water leaving Tank 241-C-106 via the ventilation system can be reduced by approximately an order of magnitude

Measuring Radionuclides in the environment: radiological quantities and sampling designs

International Nuclear Information System (INIS)

Voigt, G.

1998-10-01

One aim of the workshop was to support and provide an ICRU report committee (International Union of Radiation Units) with actual information on techniques, data and knowledge of modern radioecology when radionuclides are to be measured in the environment. It has been increasingly recognised that some studies in radioecology, especially those involving both field sampling and laboratory measurements, have not paid adequate attention to the problem of obtaining representative, unbiased samples. This can greatly affect the quality of scientific interpretation, and the ability to manage the environment. Further, as the discipline of radioecology has developed, it has seen a growth in the numbers of quantities and units used, some of which are ill-defined and which are non-standardised. (orig.)

Is the dose equivalent index a quantity to be measured

International Nuclear Information System (INIS)

Wagner, S.R.

1980-01-01

ICRP introduced the concept of Effective Dose Equivalent H(sub)E and fixed the basic limits of radiation exposure in terms of H(sub)I. As H(sub)E cannot be measured, ICRP stated that with external exposure to penetrating radiation the limitation of the Dose Equivalent Index H(sub)I would afford at least as good a level of protection. However, difficulties arise in measuring H(sub)I and in calibrating instruments in terms of H(sub)I, since the height and location of the dose equivalent maximum in the sphere which is the phantom used in the definition of H(sub)I, depend on the energy and the angular distribution of the incident radiation. That is, H(sub)I is not an additive quantity relative to the partial H(sub)I(sub)i-values of the different energy and angular components. Hence, 1) the distribution of dose equivalent in the sphere must be measured in full for a determination of H(sub)I, and 2) it is not possible to calibrate an instrument which does not exhibit the scattering and absorption properties of the sphere, consistently for arbitrary radiation fields in terms of H(sub)I. Thus the calibration in an unidirectional beam would infer an uncertainty which may amount to a factor of up to 4. This would hardly be tolerable as a base for radiation protection provisions. An alternative is to introduce operational quantities which are additive, e.g. 1) the sum of maxima of the dose equivalent distributions in the sphere produced by different radiation components, and 2) the mean dose equivalent in the sphere. Their relation to H(sub)E for different types of radiation and consequences on secondary limits are discussed. (H.K.)

The covariance matrix of derived quantities and their combination

International Nuclear Information System (INIS)

Zhao, Z.; Perey, F.G.

1992-06-01

The covariance matrix of quantities derived from measured data via nonlinear relations are only approximate since they are functions of the measured data taken as estimates for the true values of the measured quantities. The evaluation of such derived quantities entails new estimates for the true values of the measured quantities and consequently implies a modification of the covariance matrix of the derived quantities that was used in the evaluation process. Failure to recognize such an implication can lead to inconsistencies between the results of different evaluation strategies. In this report we show that an iterative procedure can eliminate such inconsistencies

Method and means for determining heat quantities

Energy Technology Data Exchange (ETDEWEB)

Waasdorp, G G; de Jong, J J; Bijl, A

1965-08-24

To determine the quantity of potential heat W that has flowed past a certain point in a certain time, the velocity of the combustible Q, the temperature T, and the specific gravity YDTU are measured, and these values are transmitted to a computer which automatically calculates the quantity: ..pi..EQUATION/sup -/ in which delta T is the difference between the combustible temperature T and a reference temperature, and in which the relation f(YDTU, delta T) represents the heat of combustion as a function of the quantities YDTU and delta T and possibly other properties of the combustible. Alternatively the quantity: ..pi..EQUATION/sup -/ may be measured; here the quantities have the same meaning as above.

Measuring cannabis consumption: Psychometric properties of the Daily Sessions, Frequency, Age of Onset, and Quantity of Cannabis Use Inventory (DFAQ-CU).

Science.gov (United States)

Cuttler, Carrie; Spradlin, Alexander

2017-01-01

We created the Daily Sessions, Frequency, Age of Onset, and Quantity of Cannabis Use Inventory (DFAQ-CU) because the current lack of psychometrically sound inventories for measuring these dimensions of cannabis use has impeded research on the effects of cannabis in humans. A sample of 2,062 cannabis users completed the DFAQ-CU and was used to assess the DFAQ-CU's factor structure and reliability. To assess validity, a subsample of 645 participants completed additional measures of cannabis dependence and problems (Marijuana Smoking History Questionnaire [MSHQ], Timeline Followback [TLFB], Cannabis Abuse Screening Test [CAST], Cannabis Use Disorders Identification Test Revised [CUDIT-R], Cannabis Use Problems Identification Test [CUPIT], and Alcohol Use Disorder Identification Test [AUDIT]). A six-factor structure was revealed, with factors measuring: daily sessions, frequency, age of onset, marijuana quantity, cannabis concentrate quantity, and edibles quantity. The factors were reliable, with Cronbach's alpha coefficients ranging from .69 (daily sessions) to .95 (frequency). Results further provided evidence for the factors' convergent (MSHQ, TLFB), predictive (CAST, CUDIT-R, CUPIT), and discriminant validity (AUDIT). The DFAQ-CU is the first psychometrically sound inventory for measuring frequency, age of onset, and quantity of cannabis use. It contains pictures of marijuana to facilitate the measurement of quantity of marijuana used, as well as questions to assess the use of different forms of cannabis (e.g., concentrates, edibles), methods of administering cannabis (e.g., joints, hand pipes, vaporizers), and typical THC levels. As such, the DFAQ-CU should help facilitate research on frequency, quantity, and age of onset of cannabis use.

Measuring cannabis consumption: Psychometric properties of the Daily Sessions, Frequency, Age of Onset, and Quantity of Cannabis Use Inventory (DFAQ-CU.

Directory of Open Access Journals (Sweden)

Carrie Cuttler

Full Text Available We created the Daily Sessions, Frequency, Age of Onset, and Quantity of Cannabis Use Inventory (DFAQ-CU because the current lack of psychometrically sound inventories for measuring these dimensions of cannabis use has impeded research on the effects of cannabis in humans.A sample of 2,062 cannabis users completed the DFAQ-CU and was used to assess the DFAQ-CU's factor structure and reliability. To assess validity, a subsample of 645 participants completed additional measures of cannabis dependence and problems (Marijuana Smoking History Questionnaire [MSHQ], Timeline Followback [TLFB], Cannabis Abuse Screening Test [CAST], Cannabis Use Disorders Identification Test Revised [CUDIT-R], Cannabis Use Problems Identification Test [CUPIT], and Alcohol Use Disorder Identification Test [AUDIT].A six-factor structure was revealed, with factors measuring: daily sessions, frequency, age of onset, marijuana quantity, cannabis concentrate quantity, and edibles quantity. The factors were reliable, with Cronbach's alpha coefficients ranging from .69 (daily sessions to .95 (frequency. Results further provided evidence for the factors' convergent (MSHQ, TLFB, predictive (CAST, CUDIT-R, CUPIT, and discriminant validity (AUDIT.The DFAQ-CU is the first psychometrically sound inventory for measuring frequency, age of onset, and quantity of cannabis use. It contains pictures of marijuana to facilitate the measurement of quantity of marijuana used, as well as questions to assess the use of different forms of cannabis (e.g., concentrates, edibles, methods of administering cannabis (e.g., joints, hand pipes, vaporizers, and typical THC levels. As such, the DFAQ-CU should help facilitate research on frequency, quantity, and age of onset of cannabis use.

Immunocapture and microplate-based activity and quantity measurement of pyruvate dehydrogenase in human peripheral blood mononuclear cells.

Science.gov (United States)

Liu, Xiaowen; Pervez, Hira; Andersen, Lars W; Uber, Amy; Montissol, Sophia; Patel, Parth; Donnino, Michael W

2015-01-01

Pyruvate dehydrogenase (PDH) activity is altered in many human disorders. Current methods require tissue samples and yield inconsistent results. We describe a modified method for measuring PDH activity from isolated human peripheral blood mononuclear cells (PBMCs). RESULTS/METHODOLOGY: We found that PDH activity and quantity can be successfully measured in human PBMCs. Freeze-thaw cycles cannot efficiently disrupt the mitochondrial membrane. Processing time of up to 20 h does not affect PDH activity with proteinase inhibitor addition and a detergent concentration of 3.3% showed maximum yield. Sample protein concentration is correlated to PDH activity and quantity in human PBMCs from healthy subjects. Measuring PDH activity from PBMCs is a novel, easy and less invasive way to further understand the role of PDH in human disease.

Flip-flop electrometer: a system for measuring radiation and other physical quantities

International Nuclear Information System (INIS)

Santos, Luiz Antonio P.

2007-01-01

Several nuclear instrumentation systems operate based on the electrometer technique: dosimetry, spectrometry and calibration. In general, electrometers are expensive and require a sophisticated calibration at secondary laboratories. The problem is that the electrical current is very low, picoampere or femtoampere, and it is very difficult to be measured. The purpose of this work is to show an electrometer system based on the flip-flop circuitry that can be used in innumerous applications in accurate instrumentation and metrology of physical quantities. Actually, an electronic flip-flop register is used as frequency generator. It was possible to build it by using an analog-digital feedback (ADF) between the device output and a schimitt-trigger field sensor (STFS) at the device input. When a very low electrical current enters in the STFS circuitry the output change the logical state and the ADF circuitry acts in the input to make the circuit oscillate. The digital oscillation frequency is proportional to the very low input current which comes from a radiation detector or scintillation dosimeter. The Flip-flop electrometer R was calibrated with a 6430 Keithley R sub-femto-amperemeter. The great advantage is its low cost and it can be used for measurements of any type of detector or transducer: ion chamber, photodiode, phototransistor, scintillator, TLD or temperature, pressure and humidity sensor, etc. An application software that controls the Flip-flop electrometer will also be presented. The software, called DoseX, can program the instrument, change the conversion factors from different detection systems and choose the physical quantity to be measured dependent on the transducer. (author)

A Viewpoint on the Quantity "Plane Angle"

Science.gov (United States)

Eder, W. E.

1982-01-01

Properties of the quantity "plane angle" are explored under the hypothesis that it is a dimensional quantity. The exploration proceeds especially with respect to the physical concept, its mathematical treatment, vector concepts, measurement theory, units of related quantities, engineering pragmatism, and SI. An attempt is made to bring these different relations into a rational, logical and consistent framework, and thus to justify the hypothesis. Various types of vectorial quantities are recognized, and their properties described with an outline of the necessary algebraic manipulations. The concept of plane angle is amplified, and its interdependence with the circular arc is explored. The resulting units of plane angle form a class of similar scales of measurement. Consequences of the confirmed hypothesis are developed for mathematical expressions involving trigonometric functions, rotational volumes and areas, mathematical limits, differentiation and series expansion. Consequences for mechanical rotational quantities are developed, with proposals for revisions to a number of expressions for derived units within SI. A revised definition for the quantity "plane angle" is stated to take account of the developed insights. There is a clear need to reconsider the status of plane angle and some other quantities within the international framework of SI.

Immunocapture and microplate-based activity and quantity measurement of pyruvate dehydrogenase in human peripheral blood mononuclear cells

Science.gov (United States)

Liu, Xiaowen; Pervez, Hira; Andersen, Lars W; Uber, Amy; Montissol, Sophia; Patel, Parth; Donnino, Michael W

2015-01-01

Background Pyruvate dehydrogenase (PDH) activity is altered in many human disorders. Current methods require tissue samples and yield inconsistent results. We describe a modified method for measuring PDH activity from isolated human peripheral blood mononuclear cells (PBMCs). Results/Methodology We found that PDH activity and quantity can be successfully measured in human PBMCs. Freeze-thaw cycles cannot efficiently disrupt the mitochondrial membrane. Processing time of up to 20 h does not affect PDH activity with proteinase inhibitor addition and a detergent concentration of 3.3% showed maximum yield. Sample protein concentration is correlated to PDH activity and quantity in human PBMCs from healthy subjects. Conclusion Measuring PDH activity from PBMCs is a novel, easy and less invasive way to further understand the role of PDH in human disease. PMID:25826140

Are necessary unmeasurable quantities in radiation protection?

International Nuclear Information System (INIS)

David, M.G.; Correa, M.F.; Videira, A.A.P.

2016-01-01

We discuss in this paper the metrological status of unmeasurable protection quantities and the need to maintain these kind of quantities in the system. The discussion is based on reports from the institutions responsible for the quantities and on scientific publications. In conclusion, we can say that there are alternatives for changing the system in a way that it keep just measurable quantities, nevertheless the present system is well assimilated. Even though a proposal yet to be presented for changing the system, although might simplify and improve it, is not intended to overcome the existence of unmeasurable quantities or the two kinds of quantities. (author)

Process for carrying out analyses based on concurrent reactions

Energy Technology Data Exchange (ETDEWEB)

Glover, J S; Shepherd, B P

1980-01-03

The invention refers to a process for carrying out analyses based on concurrent reactions. A part of a compound to be analysed is subjected with a standard quantity of this compound in a labelled form to a common reaction with a standard quantity of a reagent, which must be less than the sum of the two parts of the reacting compound. The parts of the marked reaction compound and the labelled final compound resulting from the concurrence are separated in a tube (e.g. by centrifuging) after forced phase change (precipitation, absorption etc.) and the radio-activity of both phases in contact is measured separately. The shielded measuring device developed for this and suitable for centrifuge tubes of known dimensions is also included in the patent claims. The insulin concentration of a defined serum is measured as an example of the applications of the method (Radioimmunoassay).

Definition, significance and measurement of quantities pertaining to the oxygen carrying properties of human blood

NARCIS (Netherlands)

Zijlstra, WG; Maas, AHJ; Moran, RF

1996-01-01

A consistent set of definitions is given of the principal quantities pertaining to the oxygen transport by the blood, and of their mutual relationships, in relation to the methods used in their measurement. At the core is the correct definition of oxygen saturation, the deviation of which has

Approach to determine measurement uncertainty in complex nanosystems with multiparametric dependencies and multivariate output quantities

Science.gov (United States)

Hampel, B.; Liu, B.; Nording, F.; Ostermann, J.; Struszewski, P.; Langfahl-Klabes, J.; Bieler, M.; Bosse, H.; Güttler, B.; Lemmens, P.; Schilling, M.; Tutsch, R.

2018-03-01

In many cases, the determination of the measurement uncertainty of complex nanosystems provides unexpected challenges. This is in particular true for complex systems with many degrees of freedom, i.e. nanosystems with multiparametric dependencies and multivariate output quantities. The aim of this paper is to address specific questions arising during the uncertainty calculation of such systems. This includes the division of the measurement system into subsystems and the distinction between systematic and statistical influences. We demonstrate that, even if the physical systems under investigation are very different, the corresponding uncertainty calculation can always be realized in a similar manner. This is exemplarily shown in detail for two experiments, namely magnetic nanosensors and ultrafast electro-optical sampling of complex time-domain signals. For these examples the approach for uncertainty calculation following the guide to the expression of uncertainty in measurement (GUM) is explained, in which correlations between multivariate output quantities are captured. To illustate the versatility of the proposed approach, its application to other experiments, namely nanometrological instruments for terahertz microscopy, dimensional scanning probe microscopy, and measurement of concentration of molecules using surface enhanced Raman scattering, is shortly discussed in the appendix. We believe that the proposed approach provides a simple but comprehensive orientation for uncertainty calculation in the discussed measurement scenarios and can also be applied to similar or related situations.

Thermal quantities of 46Ti

International Nuclear Information System (INIS)

Rahmatinejad, A.; Razavi, R.; Kakavand, T.

2015-01-01

Thermodynamic quantities of 46 Ti have been calculated in the framework of the BCS model with inclusion of modified nuclear pairing gap (MPBCS) that was proposed in our previous publication. Using modified paring gap results in an S-shaped heat capacity curve at critical temperature with a smooth behavior instead of singular behavior of the same curve in the BCS calculations. In addition the thermal quantities have been extracted within the framework of a canonical ensemble according to the new experimental data on nuclear level densities measured by the Oslo group. Comparison shows a good agreement between our calculations in MPBCS and the extracted quantities in the canonical ensemble framework

Ultrasonic fluid quantity measurement in dynamic vehicular applications a support vector machine approach

CERN Document Server

Terzic, Jenny; Nagarajah, Romesh; Alamgir, Muhammad

2013-01-01

Accurate fluid level measurement in dynamic environments can be assessed using a Support Vector Machine (SVM) approach. SVM is a supervised learning model that analyzes and recognizes patterns. It is a signal classification technique which has far greater accuracy than conventional signal averaging methods. Ultrasonic Fluid Quantity Measurement in Dynamic Vehicular Applications: A Support Vector Machine Approach describes the research and development of a fluid level measurement system for dynamic environments. The measurement system is based on a single ultrasonic sensor. A Support Vector Machines (SVM) based signal characterization and processing system has been developed to compensate for the effects of slosh and temperature variation in fluid level measurement systems used in dynamic environments including automotive applications. It has been demonstrated that a simple ν-SVM model with Radial Basis Function (RBF) Kernel with the inclusion of a Moving Median filter could be used to achieve the high levels...

Measurement of organic carbon quantity at chemoautorophic bacterium; Kagaku dokuritsu eiyo saikin ni okeru yuki tansoryo no sokutei ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Tsuda, I; Kato, K; Nozaki, K [Electrotechnical Laboratory, Tsukuba (Japan); Kurokawa, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1996-10-27

Described herein is the method for analyzing quantity of organic carbon synthesized by chemoautotrophic bacterium. It is based on the combustion-infrared spectroscopy, which is normally adopted for quantitative analysis of organic carbon. The problems involved in the measurement of organic compounds synthesized by iron-oxidizing bacteria are noise by culture medium components, aging of gas analyzer and contamination with organic compounds from a silicon plug. The measures taken in this study against these problems include comparison of the results with a medium containing iron-oxidizing bacteria with those with a medium free of these bacteria, calibration with the standard solution for each measurement, and replacement of a silicone plug by a silicon cap. Organic carbon is measured by a TOC-5000 analyzer equipped with an automatic sample feeder ASI-5000. Biomass density is determined by the MPN method. It is confirmed that organic carbon quantity is almost in proportion to biomass density, a phenomenon which can be used to determine organic carbon quantity. 7 refs., 6 figs., 1 tab.

Loneliness in Early Adolescence: Friendship Quantity, Friendship Quality, and Dyadic Processes.

Science.gov (United States)

Lodder, Gerine M A; Scholte, Ron H J; Goossens, Luc; Verhagen, Maaike

2017-01-01

Friendship quantity and quality are related to adolescent loneliness, but the exact link between these constructs is not well understood. The present study aimed to examine whether adolescents' perception of friendship quantity and quality, and the perceptions of their peers, were related to loneliness. We examined the relation between loneliness and the number of unilateral and reciprocal friendships and compared the views of best friendship quality. Overall, 1,172 Dutch adolescents (49.1% male, M age = 12.81, SD = .43) nominated their friends and rated their friendship quality. Friendship quantity was measured using sociometrics to distinguish reciprocated and unilateral (i.e., one-sided) friendships. The analyses indicated that loneliness was related to fewer reciprocal and unilateral-received friendships (i.e., the adolescent received a friendship nomination but did not reciprocate that nomination) and a lower quality of best friendship. Actor-partner interdependence analyses revealed that adolescents' loneliness was related to a less positive evaluation of their friendship, as reported by adolescents themselves (i.e., a significant actor effect) but not by their friends (i.e., nonsignificant partner effect). These findings (a) indicate that loneliness is negatively related to the number of friends adolescents have, as perceived by themselves and their peers and (b) suggest that, once a friendship is established, lonely adolescents may interpret the friendship quality less positively compared to their friends. Implications of these findings for our current understanding of adolescent loneliness are discussed, and suggestions for future research are outlined.

Measurement of uranium quantities by fluorescence-X using neuronal techniques

International Nuclear Information System (INIS)

Vigneron, V.; Martinez, J.M.; Simon, A.C.; Junca, R.

1995-01-01

Layered neural networks are a class of models based on neural computation in biological systems. Connexionists models are made of a large number of simple computing structures, highly interconnected. The weights assigned to the connections enable the encoding of the knowledge required for a task. They can be trained to learn any input-output relation after selecting a suitable architecture. This method appears useful in those cases in which a simple operation and a fast response are needed, together with a reasonable accuracy. They are applied here to the automatic analysis of X-ray fluorescence spectra, obtained with plastic bottles irradiate by collimated beam of photons, emitted by a sealed source of iridium. The method could allow the surveillance of the measurement of uranium quantities in nuclear fuel cycles in processing plants. (authors). 11 refs., 4 figs

Fundamental data analyses for measurement control

International Nuclear Information System (INIS)

Campbell, K.; Barlich, G.L.; Fazal, B.; Strittmatter, R.B.

1987-02-01

A set of measurment control data analyses was selected for use by analysts responsible for maintaining measurement quality of nuclear materials accounting instrumentation. The analyses consist of control charts for bias and precision and statistical tests used as analytic supplements to the control charts. They provide the desired detection sensitivity and yet can be interpreted locally, quickly, and easily. The control charts provide for visual inspection of data and enable an alert reviewer to spot problems possibly before statistical tests detect them. The statistical tests are useful for automating the detection of departures from the controlled state or from the underlying assumptions (such as normality). 8 refs., 3 figs., 5 tabs

Critical review of the current radiation protection quantities and units

International Nuclear Information System (INIS)

Sabol, J.

1998-01-01

Examples exist in dosimetry and radiation protection where primary attention was focused on the unit rather than the corresponding quantity. Another difficulty arises from the fact that quantities in this field cannot be considered as pure physical quantities, they are rather biophysical quantities. There are too many quantities (e. g. 17 quantities based on the dose equivalent), with differences in numerical values of 'similar' quantities, not always satisfactory approximations of virtually unmeasurable quantities by measurable quantities, inconsistency in definitions and interpretations of quantities of some international expert bodies, and problems of weighting and conversion factors. (M.D.)

Conceptual Model of Quantities, Units, Dimensions, and Values

Science.gov (United States)

Rouquette, Nicolas F.; DeKoenig, Hans-Peter; Burkhart, Roger; Espinoza, Huascar

2011-01-01

JPL collaborated with experts from industry and other organizations to develop a conceptual model of quantities, units, dimensions, and values based on the current work of the ISO 80000 committee revising the International System of Units & Quantities based on the International Vocabulary of Metrology (VIM). By providing support for ISO 80000 in SysML via the International Vocabulary of Metrology (VIM), this conceptual model provides, for the first time, a standard-based approach for addressing issues of unit coherence and dimensional analysis into the practice of systems engineering with SysML-based tools. This conceptual model provides support for two kinds of analyses specified in the International Vocabulary of Metrology (VIM): coherence of units as well as of systems of units, and dimension analysis of systems of quantities. To provide a solid and stable foundation, the model for defining quantities, units, dimensions, and values in SysML is explicitly based on the concepts defined in VIM. At the same time, the model library is designed in such a way that extensions to the ISQ (International System of Quantities) and SI Units (Systeme International d Unites) can be represented, as well as any alternative systems of quantities and units. The model library can be used to support SysML user models in various ways. A simple approach is to define and document libraries of reusable systems of units and quantities for reuse across multiple projects, and to link units and quantity kinds from these libraries to Unit and QuantityKind stereotypes defined in SysML user models.

Hypergraph topological quantities for tagged social networks

Science.gov (United States)

Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

2009-09-01

Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

Calibration of personal dosemeters in terms of the ICRU operational quantities

International Nuclear Information System (INIS)

McDonald, J.C.; Hertel, N.E.

1992-01-01

The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosimeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The U.S. personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethylmethacrylate (PMMA) phantom; therefore it is necessary to relate the response of dosimeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosimeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors. (author)

Calibration of personal dosemeters in terms of the ICRU operational quantities

International Nuclear Information System (INIS)

McDonald, J.C.; Hertel, N.E.

1992-05-01

The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosemeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The US personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethymethacrylate (PMMA) phantom, therefore it is necessary to relate the response of dosemeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosemeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors

New quantities in radiation protection and conversion coefficients

International Nuclear Information System (INIS)

1986-01-01

Four new quantities have been proposed by the ICRP for use in radiation protection from external sources, i.e. the ambient dose equivalent, the directional dose equivalent, the individual dose equivalent (penetrating), and the individual dose equivalent (superficial). These quantities are briefly described together with two new concepts of expanded and aligned fields. The BCRU recommends that these quantities should be adopted for use in the UK together with conversion coefficients when re-calibrating existing instruments, reporting the results of measurements and designing instruments. (UK)

Comparative Assessment of Physical and Social Determinants of Water Quantity and Water Quality Concerns

Science.gov (United States)

Gunda, T.; Hornberger, G. M.

2017-12-01

Concerns over water resources have evolved over time, from physical availability to economic access and recently, to a more comprehensive study of "water security," which is inherently interdisciplinary because a secure water system is influenced by and affects both physical and social components. The concept of water security carries connotations of both an adequate supply of water as well as water that meets certain quality standards. Although the term "water security" has many interpretations in the literature, the research field has not yet developed a synthetic analysis of water security as both a quantity (availability) and quality (contamination) issue. Using qualitative comparative and multi-regression analyses, we evaluate the primary physical and social factors influencing U.S. states' water security from a quantity perspective and from a quality perspective. Water system characteristics are collated from academic and government sources and include access/use, governance, and sociodemographic, and ecosystem metrics. Our analysis indicates differences in variables driving availability and contamination concerns; for example, climate is a more significant determinant in water quantity-based security analyses than in water quality-based security analyses. We will also discuss coevolution of system traits and the merits of constructing a robust water security index based on the relative importance of metrics from our analyses. These insights will improve understanding of the complex interactions between quantity and quality aspects and thus, overall security of water systems.

Testing the algorithms for automatic identification of errors on the measured quantities of the nuclear power plant. Verification tests

International Nuclear Information System (INIS)

Svatek, J.

1999-12-01

During the development and implementation of supporting software for the control room and emergency control centre at the Dukovany nuclear power plant it appeared necessary to validate the input quantities in order to assure operating reliability of the software tools. Therefore, the development of software for validation of the measured quantities of the plant data sources was initiated, and the software had to be debugged and verified. The report contains the proposal for and description of the verification tests for testing the algorithms of automatic identification of errors on the observed quantities of the NPP by means of homemade validation software. In particular, the algorithms treated serve the validation of the hot leg temperature at primary circuit loop no. 2 or 4 at the Dukovany-2 reactor unit using data from the URAN and VK3 information systems, recorded during 3 different days. (author)

Is the dose equivalent index a quantity to be measured

International Nuclear Information System (INIS)

Wagner, S.R.

1980-01-01

The following modifying factors are briefly considered in relation to the ambiguities and limitations of the Dose Equivalent Index: 1) Variations with time or of the movement of the exposed person 2) Irradiation geometry 3) Effect of radiation energy 4) Instrument performance and calibration, and other operational quantities. (U.K.)

UMTS signal measurements with digital spectrum analysers

International Nuclear Information System (INIS)

Licitra, G.; Palazzuoli, D.; Ricci, A. S.; Silvi, A. M.

2004-01-01

The launch of the Universal Mobile Telecommunications System (UNITS), the most recent mobile telecommunications standard has imposed the requirement of updating measurement instrumentation and methodologies. In order to define the most reliable measurement procedure, which is aimed at assessing the exposure to electromagnetic fields, modern spectrum analysers' features for correct signal characterisation has been reviewed. (authors)

Quantity and structure of word knowledge across adulthood.

Science.gov (United States)

Salthouse, Timothy A

2014-09-01

Cross-sectional and longitudinal data from moderately large samples of healthy adults confirmed prior findings of age-related declines in measures of the quantity of word knowledge beginning around age 65. Additional analyses were carried out to investigate the interrelations of different types of vocabulary knowledge at various periods in adulthood. Although the organizational structures were similar in adults of different ages, scores on tests with different formats had weaker relations to a higher-order vocabulary construct beginning when adults were in their 60's. The within-person dispersion among different vocabulary test scores was also greater after about 65 years of age. The discovery of quantitative decreases in amount of knowledge occurring at about the same age as qualitative shifts in the structure of knowledge raises the possibility that the two types of changes may be causally linked.

Using Inequality Measures to Incorporate Environmental Justice into Regulatory Analyses

Science.gov (United States)

Harper, Sam; Ruder, Eric; Roman, Henry A.; Geggel, Amelia; Nweke, Onyemaechi; Payne-Sturges, Devon; Levy, Jonathan I.

2013-01-01

Formally evaluating how specific policy measures influence environmental justice is challenging, especially in the context of regulatory analyses in which quantitative comparisons are the norm. However, there is a large literature on developing and applying quantitative measures of health inequality in other settings, and these measures may be applicable to environmental regulatory analyses. In this paper, we provide information to assist policy decision makers in determining the viability of using measures of health inequality in the context of environmental regulatory analyses. We conclude that quantification of the distribution of inequalities in health outcomes across social groups of concern, considering both within-group and between-group comparisons, would be consistent with both the structure of regulatory analysis and the core definition of environmental justice. Appropriate application of inequality indicators requires thorough characterization of the baseline distribution of exposures and risks, leveraging data generally available within regulatory analyses. Multiple inequality indicators may be applicable to regulatory analyses, and the choice among indicators should be based on explicit value judgments regarding the dimensions of environmental justice of greatest interest. PMID:23999551

Methods for analysing cardiovascular studies with repeated measures

NARCIS (Netherlands)

Cleophas, T. J.; Zwinderman, A. H.; van Ouwerkerk, B. M.

2009-01-01

Background. Repeated measurements in a single subject are generally more similar than unrepeated measurements in different subjects. Unrepeated analyses of repeated data cause underestimation of the treatment effects. Objective. To review methods adequate for the analysis of cardiovascular studies

Review of clinical approaches and diagnostic quantities used in pedobarographic measurements.

Science.gov (United States)

Deschamps, K; Roosen, P; Nobels, F; Deleu, P A; Birch, I; Desloovere, K; Bruyninckx, H; Matricali, G; Staes, F

2015-03-01

The non-invasive nature of pedobarographic measurements is particularly attractive to researchers for analyzing and characterizing the impact of specific pathological foot conditions. However, adequate clinical use of pedobarographic technology requires a profound technical and methodological knowledge. Several papers summarized the technical capacities of pedobarographic technology. Moreover, methodological expertise has grown considerably during the last two decades. Therefore, two crucial decisions have to be made before pathomechanical modelling or functional interpretation of foot and lower limb disorders can be pursued. The first is the selection of the specific method to analyse the dynamic plantar footprint, and the second is the choice of parameters to quantify the results. In the first part of this paper, we review the different methods used to analyse the dynamic plantar footprint and discuss their conceptual backgrounds. We also aim to illustrate the clinical relevance of each method and elaborate on the future perspectives. In the second part, we review quantification methods of pedobarographic measurements. The latter is of primary relevance to clinicians and investigators with a special interest in foot and lower limb biomechanics.

Fluid Vessel Quantity using Non-Invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

Science.gov (United States)

Garofalo, Anthony A.

2013-01-01

The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

Influence of relative humidity and temperature on quantity of electric charge of static protective clothing used in petrochemical industry

Science.gov (United States)

Zhang, Yunpeng; Liu, Quanzhen; Liu, Baoquan; Li, Yipeng; Zhang, Tingting

2013-03-01

In this paper, the working principle of static protective clothing and its testing method of quantity of electric charge are introduced, and the influence of temperature and relative humidity on the quantity of electric charge (qe) of static protective clothing is studied by measuring qe of different clothing samples. The result shows that temperature and relative humidity can influence qe of static protective clothing to some extent and the influence of relative humidity is bigger than that of temperature. According to experimental results, the relationship of qe and relative humidity and temperature was analysed, and the safety boundary of quantity of electric charge is discussed. In order to reduce the occurrence of electrostatic accidents and ensure safe production and operation of petrochemical industry, some suggestions on choosing and using of static protective clothing are given for guaranteeing its static protective performance.

Information content of X-ray analyses characterizing the structural state of cocoa butter and their manufacturing conditions

International Nuclear Information System (INIS)

Foersterling, G.; Kleinstueck, K.; Loeser, U.; Tscheuschner, H.D.

1980-01-01

Direct X-ray analyses performed on the model substance cocoa butter revealed a direct relation between the easily measurable quantities of the diffraction pattern (site, intensity and sharpness of the reflexes) and the characteristic parameters of the sample (lattice constants, 'perfection' and crystalline fraction), which can be derived from these measured quantities, on the one side, and the technological parameters of the manufacturing process (tempering regimen and storage conditions) on the other side. An automated X-ray diffractometer was used and an optimal measuring strategy was developed the measuring effects being sufficiently great as compared to the measuring errors and the characterization of one sample requiring only 30 - 60 minutes. (author)

Correlates of job satisfaction amongst quantity surveyors in consulting firms in Lagos, Nigeria

Directory of Open Access Journals (Sweden)

Henry Ndubuisi Onukwube

2012-05-01

Full Text Available Job satisfaction is the sense of well- being, good feeling and positive mental state that emerge in an incumbent worker when his obtained reward consequent upon his performance is congruent with his equitable reward.The aim of this study is to ascertain the levels of job satisfaction amongst quantity surveyors in consulting firms in Lagos, Nigeria. Biographical and job descriptive index questionnaires (JDI were administered to gather the data. The JDI measures job satisfaction on five facets, namely, pay, promotions, supervision, co-workers and the work itself. A total of 100 questionnaires were collected and used for the study. The survey covered quantity surveyors in consulting firms in Lagos and the respondents were selected using stratified random sampling technique. Data collected were analysed using descriptive statistics, correlation matrix, t-test and one way anova. Findings of the study revealed that the respondents were satisfied with the relationship with co-workers, nature of work and the supervision they receive. Major sources of dissatisfaction are promotion and salaries of the respondents. This finding is a bold step and necessary benchmark for resolving major sources of dissatisfaction among quantity surveyors in consulting firms. The roles of other contextual factors on job satisfaction need to be contemplated for future research.

16 CFR 500.7 - Net quantity of contents, method of expression.

Science.gov (United States)

2010-01-01

... expression. The net quantity of contents shall be expressed in terms of weight or mass, measure, numerical... consumers. The net quantity of contents statement shall be in terms of fluid measure if the commodity is liquid, or in terms of weight or mass if the commodity is solid, semi-solid, or viscous, or a mixture of...

Radiation quantities and units

International Nuclear Information System (INIS)

2013-01-01

This fifth chapter presents the conceptual evolution, the definition procedures, the radiological quantities themselves, the relation between them, the new operational quantities and the new quantities defined in the ICRP 60 that replaced ICRP 26 and was included in the CNEN-NN-3.01 standard of 2011

Calibration of personal dosimeters: Quantities and terminology

International Nuclear Information System (INIS)

Aleinikov, V.E.

1999-01-01

The numerical results obtained in the interpretation of individual monitoring of external radiation depend not only on the accurate calibration of the radiation measurement instruments involved, but also on the definition of the quantities in term of which these instruments are calibrated The absence of uniformity in terminology not only makes it difficult to understand properly the scientific and technical literature but can also lead to incorrect interpretation of particular concepts and recommendations. In this paper, brief consideration is given to definition of radiation quantities and terminology used in calibration procedures. (author)

Influence of relative humidity and temperature on quantity of electric charge of static protective clothing used in petrochemical industry

International Nuclear Information System (INIS)

Zhang, Yunpeng; Liu, Quanzhen; Liu, Baoquan; Li, Yipeng; Zhang, Tingting

2013-01-01

In this paper, the working principle of static protective clothing and its testing method of quantity of electric charge are introduced, and the influence of temperature and relative humidity on the quantity of electric charge (q e ) of static protective clothing is studied by measuring q e of different clothing samples. The result shows that temperature and relative humidity can influence q e of static protective clothing to some extent and the influence of relative humidity is bigger than that of temperature. According to experimental results, the relationship of q e and relative humidity and temperature was analysed, and the safety boundary of quantity of electric charge is discussed. In order to reduce the occurrence of electrostatic accidents and ensure safe production and operation of petrochemical industry, some suggestions on choosing and using of static protective clothing are given for guaranteeing its static protective performance.

Sophistication of 14C measurement at JAEA-AMS-MUTSU. Attempt on a small quantity of sample

International Nuclear Information System (INIS)

Tanaka, Takayuki; Kabuto, Shoji; Kinoshita, Naoki; Yamamoto, Nobuo

2010-01-01

In the investigations on substance dynamics using the molecular weight and chemical fractionation, the utilization of 14 C measurement by an accelerator mass spectrometry (AMS) have started. As a result of the fractionation, sample contents required for AMS measurement have been downsized. We expect that this trend toward a small quantity of sample will be steadily accelerated in the future. As 14 C measurement by AMS established at Mutsu office require about 2 mg of sample content at present, our AMS lags behind the others in the trend. We try to downsize the needed sample content for 14 C measurement by our AMS. In this study, we modified the shape of the target-piece in which the sample is packed and which is regularly needed to radiocarbon measurement by our AMS. Moreover, we improved on the apparatus needed to pack the sample. As a result of the improvement, we revealed that it is possible to measure the 14 C using our AMS even by the amount of the sample of about 0.5 mg. (author)

Discussion on concepts for radiological dosimetric quantities in the Japan Health Physics Society

International Nuclear Information System (INIS)

Takahashi, Fumiaki; Oda, Keiji

2007-01-01

Many dosimetric quantities have been used for radiation protection purpose. The International Commission on Radiological Protection (ICRP) has recommended protection quantities and the International Commission on Radiation Units and Measurements (ICRU) has introduced operational quantities to provide a reasonable estimate of the protection quantities. Enthusiastic discussions are continuously made on the issues of the dosimetric quantities, such as basic biological data for the definition of these quantities and applicability of the quantities to actual radiation protection practice. At the moment, some changes are being proposed concerning dosimetric quantities in the draft recommendations of ICRP, opened for consultation in recent years. Thus, the Japan Health Physics Society (JHPS) established the Expert Committee on concepts of Dosimetric Quantities used in radiological protection (ECDQ) in April 2005 to reviewed and discuss issues in the dosimetric quantities. (author)

Variations of influence quantities in industrial irradiators and their effect on dosimetry performance

International Nuclear Information System (INIS)

Chu, R.D.H.

1999-01-01

Many environmental factors, including irradiation temperature, post-irradiation storage temperature, dose rate, relative humidity, oxygen content and the energy spectrum may affect the response of dosimetry systems used in industrial radiation processing. Although the effects of individual influence quantities have been extensively studied, the variations of these influence quantities in production irradiators and the complex relationships between the effects of different influence quantities make it difficult to assess the overall effect on the measurement uncertainty. In the development of new dosimetry systems it is important to know the effect of each influence quantity and developers of new dosimetry systems should perform studies over a wide range of irradiation conditions. Analysis parameters and manufacturing specifications should be chosen to minimize the effect of influence quantities in the environments where the dosimeters will be used. Because of possible relationships between different influence quantities, care must be taken to ensure that the response function determined in the calibration of the dosimetry system is applicable for the conditions in which the dosimeters will be used. Reference standard dosimetry systems which have been thoroughly studied and have known relationships between dose response and influence quantities should be used to verify the calibration of routine dosimetry systems under the actual conditions of use. Better understanding of the variations in influence quantities in industrial irradiators may be obtained by modeling or direct measurements and may provide improvements in the calibration of routine dosimetry system and reduction of the overall measurement uncertainty. (author)

High Throughput Microplate Respiratory Measurements Using Minimal Quantities Of Isolated Mitochondria

Science.gov (United States)

Rogers, George W.; Brand, Martin D.; Petrosyan, Susanna; Ashok, Deepthi; Elorza, Alvaro A.; Ferrick, David A.; Murphy, Anne N.

2011-01-01

Recently developed technologies have enabled multi-well measurement of O2 consumption, facilitating the rate of mitochondrial research, particularly regarding the mechanism of action of drugs and proteins that modulate metabolism. Among these technologies, the Seahorse XF24 Analyzer was designed for use with intact cells attached in a monolayer to a multi-well tissue culture plate. In order to have a high throughput assay system in which both energy demand and substrate availability can be tightly controlled, we have developed a protocol to expand the application of the XF24 Analyzer to include isolated mitochondria. Acquisition of optimal rates requires assay conditions that are unexpectedly distinct from those of conventional polarography. The optimized conditions, derived from experiments with isolated mouse liver mitochondria, allow multi-well assessment of rates of respiration and proton production by mitochondria attached to the bottom of the XF assay plate, and require extremely small quantities of material (1–10 µg of mitochondrial protein per well). Sequential measurement of basal, State 3, State 4, and uncoupler-stimulated respiration can be made in each well through additions of reagents from the injection ports. We describe optimization and validation of this technique using isolated mouse liver and rat heart mitochondria, and apply the approach to discover that inclusion of phosphatase inhibitors in the preparation of the heart mitochondria results in a specific decrease in rates of Complex I-dependent respiration. We believe this new technique will be particularly useful for drug screening and for generating previously unobtainable respiratory data on small mitochondrial samples. PMID:21799747

High throughput microplate respiratory measurements using minimal quantities of isolated mitochondria.

Directory of Open Access Journals (Sweden)

George W Rogers

Full Text Available Recently developed technologies have enabled multi-well measurement of O(2 consumption, facilitating the rate of mitochondrial research, particularly regarding the mechanism of action of drugs and proteins that modulate metabolism. Among these technologies, the Seahorse XF24 Analyzer was designed for use with intact cells attached in a monolayer to a multi-well tissue culture plate. In order to have a high throughput assay system in which both energy demand and substrate availability can be tightly controlled, we have developed a protocol to expand the application of the XF24 Analyzer to include isolated mitochondria. Acquisition of optimal rates requires assay conditions that are unexpectedly distinct from those of conventional polarography. The optimized conditions, derived from experiments with isolated mouse liver mitochondria, allow multi-well assessment of rates of respiration and proton production by mitochondria attached to the bottom of the XF assay plate, and require extremely small quantities of material (1-10 µg of mitochondrial protein per well. Sequential measurement of basal, State 3, State 4, and uncoupler-stimulated respiration can be made in each well through additions of reagents from the injection ports. We describe optimization and validation of this technique using isolated mouse liver and rat heart mitochondria, and apply the approach to discover that inclusion of phosphatase inhibitors in the preparation of the heart mitochondria results in a specific decrease in rates of Complex I-dependent respiration. We believe this new technique will be particularly useful for drug screening and for generating previously unobtainable respiratory data on small mitochondrial samples.

Correlates of job satisfaction amongst quantity surveyors in consulting firms in Lagos, Nigeria

Directory of Open Access Journals (Sweden)

Henry Ndubuisi Onukwube

2012-05-01

Full Text Available Normal 0 false false false EN-US X-NONE X-NONE Job satisfaction is the sense of well- being, good feeling and positive mental state that emerge in an incumbent worker when his obtained reward consequent upon his performance is congruent with his equitable reward.The aim of this study is to ascertain the levels of job satisfaction amongst quantity surveyors in consulting firms in Lagos, Nigeria. Biographical and job descriptive index questionnaires (JDI were administered to gather the data. The JDI measures job satisfaction on five facets, namely, pay, promotions, supervision, co-workers and the work itself. A total of 100 questionnaires were collected and used for the study. The survey covered quantity surveyors in consulting firms in Lagos and the respondents were selected using stratified random sampling technique. Data collected were analysed using descriptive statistics, correlation matrix, t-test and one way anova. Findings of the study revealed that the respondents were satisfied with the relationship with co-workers, nature of work and the supervision they receive. Major sources of dissatisfaction are promotion and salaries of the respondents. This finding is a bold step and necessary benchmark for resolving major sources of dissatisfaction among quantity surveyors in consulting firms. The roles of other contextual factors on job satisfaction need to be contemplated for future research.

Twenty years of meta-analyses in orthopaedic surgery: has quality kept up with quantity?

Science.gov (United States)

Dijkman, Bernadette G; Abouali, Jihad A K; Kooistra, Bauke W; Conter, Henry J; Poolman, Rudolf W; Kulkarni, Abhaya V; Tornetta, Paul; Bhandari, Mohit

2010-01-01

As the number of studies in the literature is increasing, orthopaedic surgeons highly depend on meta-analyses as their primary source of scientific evidence. The objectives of this review were to assess the scientific quality and number of published meta-analyses on orthopaedics-related topics over time. We conducted, in duplicate and independently, a systematic review of published meta-analyses in orthopaedics in the years 2005 and 2008 and compared them with a previous systematic review of meta-analyses from 1969 to 1999. A search of electronic databases (MEDLINE, EMBASE, and the Cochrane Database of Systematic Reviews) was performed to identify meta-analyses published in 2005 and 2008. We searched bibliographies and contacted content experts to identify additional relevant studies. Two investigators independently assessed the quality of the studies, using the Oxman and Guyatt index, and abstracted relevant data. We included forty-five and forty-four meta-analyses from 2005 and 2008, respectively. While the number of meta-analyses increased fivefold from 1999 to 2008, the mean quality score did not change significantly over time (p = 0.067). In the later years, a significantly lower proportion of meta-analyses had methodological flaws (56% in 2005 and 68% in 2008) compared with meta-analyses published prior to 2000 (88%) (p = 0.006). In 2005 and 2008, respectively, 18% and 30% of the meta-analyses had major to extensive flaws in their methodology. Studies from 2008 with positive conclusions used and described appropriate criteria for the validity assessment less often than did those with negative results. The use of random-effects and fixed-effects models as pooling methods became more popular toward 2008. Although the methodological quality of orthopaedic meta-analyses has increased in the past twenty years, a substantial proportion continues to show major to extensive flaws. As the number of published meta-analyses is increasing, a routine checklist for

Charaterisation of function spaces via mollification; fractal quantities for distributions

Directory of Open Access Journals (Sweden)

Hans Triebel

2003-01-01

Full Text Available The aim of this paper is twofold. First we characterise elements f belonging to the Besov spaces Bpqs(ℝn with s∈ℝ,  0quantities for distributions generalising well-known corresponding quantities for Radon measures.

LOFT experimental measurements uncertainty analyses. Volume XX. Fluid-velocity measurement using pulsed-neutron activation

International Nuclear Information System (INIS)

Lassahn, G.D.; Taylor, D.J.N.

1982-08-01

Analyses of uncertainty components inherent in pulsed-neutron-activation (PNA) measurements in general and the Loss-of-Fluid-Test (LOFT) system in particular are given. Due to the LOFT system's unique conditions, previously-used techniques were modified to make the volocity measurement. These methods render a useful, cost-effective measurement with an estimated uncertainty of 11% of reading

Measurement of the quantity of water in organic solvents by infrared absorption an measurement of the dielectric constants

International Nuclear Information System (INIS)

Desnoyer, M.

1959-06-01

Some chemical methods for the analysis of the quantity of water in solvents are first described, their object being the determination of the maximum error for cases where the water content is less than 1 per cent. - The first part of the work consists in describing infrared spectrometry as applied to the analysis of water in carbon tetrachloride, chloroform aniline, acetone and dioxane. A method based on isotopic exchange between heavy and light water is used on the one hand for determining the solubility of water in carbon tetrachloride and on the other hand for establishing standard solutions (sensitivity of the method). - In the second part the dielectric constant of water solvent solutions is measured. A table is presented giving the precision obtained by the two principal methods. These are comparable and further than that the appearance of the spectra suggests an interpretation of the anomalies observed in calibration curves obtained by the dielectric constant method. (author) [fr

On the turbulent flow in piston engines: Coupling of statistical theory quantities and instantaneous turbulence

Energy Technology Data Exchange (ETDEWEB)

Zentgraf, Florian; Baum, Elias; Dreizler, Andreas [Fachgebiet Reaktive Strömungen und Messtechnik (RSM), Center of Smart Interfaces (CSI), Technische Universität Darmstadt, Jovanka-Bontschits-Straße 2, 64287 Darmstadt (Germany); Böhm, Benjamin [Fachgebiet Energie und Kraftwerkstechnik (EKT), Technische Universität Darmstadt, Jovanka-Bontschits-Straße 2, 64287 Darmstadt (Germany); Peterson, Brian, E-mail: brian.peterson@ed.ac.uk [Department of Mechanical Engineering, School of Engineering, Institute for Energy Systems, University of Edinburgh, The King’s Buildings, Mayfield Road, Edinburgh EH9 3JL, Scotland (United Kingdom)

2016-04-15

Planar particle image velocimetry (PIV) and tomographic PIV (TPIV) measurements are utilized to analyze turbulent statistical theory quantities and the instantaneous turbulence within a single-cylinder optical engine. Measurements are performed during the intake and mid-compression stroke at 800 and 1500 RPM. TPIV facilitates the evaluation of spatially resolved Reynolds stress tensor (RST) distributions, anisotropic Reynolds stress invariants, and instantaneous turbulent vortical structures. The RST analysis describes distributions of individual velocity fluctuation components that arise from unsteady turbulent flow behavior as well as cycle-to-cycle variability (CCV). A conditional analysis, for which instantaneous PIV images are sampled by their tumble center location, reveals that CCV and turbulence have similar contributions to RST distributions at the mean tumble center, but turbulence is dominant in regions peripheral to the tumble center. Analysis of the anisotropic Reynolds stress invariants reveals the spatial distribution of axisymmetric expansion, axisymmetric contraction, and 3D isotropy within the cylinder. Findings indicate that the mid-compression flow exhibits a higher tendency toward 3D isotropy than the intake flow. A novel post-processing algorithm is utilized to classify the geometry of instantaneous turbulent vortical structures and evaluate their frequency of occurrence within the cylinder. Findings are coupled with statistical theory quantities to provide a comprehensive understanding of the distribution of turbulent velocity components, the distribution of anisotropic states of turbulence, and compare the turbulent vortical flow distribution that is theoretically expected to what is experimentally observed. The analyses reveal requisites of important turbulent flow quantities and discern their sensitivity to the local flow topography and engine operation.

Uncertainties of exposure-related quantities in mammographic x-ray unit quality control

International Nuclear Information System (INIS)

Gregory, Kent J.; Pattison, John E.; Bibbo, Giovanni

2006-01-01

Breast screening programs operate in many countries with mammographic x-ray units subject to stringent quality control tests. These tests include the evaluation of quantities based on exposure measurements, such as half value layer, automatic exposure control reproducibility, average glandular dose, and radiation output rate. There are numerous error sources that contribute to the uncertainty of these exposure-related quantities, some of which are unique to the low energy x-ray spectrum produced by mammographic x-ray units. For each of these exposure-related quantities, the applicable error sources and their magnitudes vary, depending on the test equipment used to make the measurement, and whether or not relevant corrections have been applied. This study has identified and quantified a range of error sources that may be used to estimate the combined uncertainty of these exposure-related quantities, given the test equipment used and corrections applied. The uncertainty analysis uses methods described by the International Standards Organization's Guide to the Expression of Uncertainty in Measurement. Examples of how these error sources combine to give the uncertainty of the exposure-related quantities are presented. Using the best test equipment evaluated in this study, uncertainties of the four exposure-related quantities at the 95% confidence interval were found to be ±1.6% (half value layer), ±0.0008 (automatic exposure control reproducibility), ±2.3% (average glandular dose), and ±2.1% (radiation output rate). In some cases, using less precise test equipment or failing to apply corrections, resulted in uncertainties more than double in magnitude

Mass spectrometry of submicrogram quantities of lead and cadmium

International Nuclear Information System (INIS)

Moraes, Noemia M.P. de; Kakazu, M.H.; Iyer, S.S.

1980-01-01

Isotope analyses of submicrogram quantities of lead and cadmium are carried out by single filament solid source mass spectrometry. Thermionic emission of Pb and Cd is enhanced using silica gel as an emitter. Details of the chemical and mass spectrometric techniques are described. The low blank levels are maintained by extra purification of the reagents. The applications of isotope ratios of Pb and Cd in environmental sciences and geochemistry are discussed. (Author) [pt

Quantity Stickiness versus Stackelberg Leadership

International Nuclear Information System (INIS)

Ferreira, F. A.

2008-01-01

We study the endogenous Stackelberg relations in a dynamic market. We analyze a twice-repeated duopoly where, in the beginning, each firm chooses either a quantity-sticky production mode or a quantity-flexible production mode. The size of the market becomes observable after the first period. In the second period, a firm can adjust its quantity if, and only if, it has adopted the flexible mode. Hence, if one firm chooses the sticky mode whilst the other chooses the flexible mode, then they respectively play the roles of a Stackelberg leader and a Stackelberg follower in the second marketing period. We compute the supply quantities at equilibrium and the corresponding expected profits of the firms. We also analyze the effect of the slope parameter of the demand curve on the expected supply quantities and on the profits.

How necessary are the new quantities

International Nuclear Information System (INIS)

Kraus, W.

1991-01-01

The necessity of the ICRU operational quantities is discussed from the point of view of practical, opertional radiation protection, on the basis of ICRU report 43. It is clear that, although the new quantities have some advantages over previous systems of operational quantities, there are some disadvantages as well. The decision to adopt these quantities is, therefore, not clear cut. (orig.)

Relationship between Performance of Quantity Surveying Students in Building Construction and Construction Measurement Courses

Directory of Open Access Journals (Sweden)

Olatunde Nathaniel Ayinde

2018-01-01

Full Text Available Stakeholders in the educational sector over the century have devoted substantial resources in seeking ways of improving students’ academic performance, yet, the desired improved academic performance has not been achieved. By appraising the relationship between the performance of Quantity Surveying (QS students in Building Construction and Construction Measurement courses; the study identified a major curriculum drafting deficiency in the QS programmes in Nigeria which if addressed could help achieve the much needed improved students’ academic performance. The specific objectives of the study were to determine the performance of QS students in Building construction and construction Measurement Courses; and to determine whether a relationship exist in the performances of QS students in the two subject areas. Purposive sampling technique was used to select Federal Polytechnic Ede, Osun State for the study. Random sampling technique was used to select 241 students who provide data for the study. Close ended questionnaire was used to collect data for the study and data was analyzed using frequency, percentile and correlation analysis. Finding indicates that 43% of the respondents on the average put up good performances in Building Construction Courses while only 19% of the respondents on the average had good grades in Construction Measurement Courses. Results also showed that a significant relationship exist between the performance of QS students in Building Construction and Construction Measurement courses as 83.3% (five out of six pair courses shows significant positive linear correlation. The study recommends that a quick curriculum re-adjustment should be initiated so as to enhance improved academic performance by QS Students especially in Construction Measurement courses.

Review on evolvement of systems of ionizing radiation quantities and units

International Nuclear Information System (INIS)

Zheng Junzheng; Zeng Zhi

2009-01-01

To scientifically and practically measure the ionizing radiation in unison is an indispensable prerequisite and foundation for the extensive uses of nuclear science and technology, development of radiological protection and safety standards, as well as prevention and treatment of ionizing radiation hazards. Concerning about the quantities and units of ionizing radiation as well as their corresponding measurement and application methods, relevant international organizations and all countries in the world generally adopt the systems proposed by the International Commission on Radiation Units and Measurements (ICRU) which is a well recognized and authoritative academic organization.In the paper,the major evolutions of the systems for ionizing radiation quantities and units in the past decades are summarized. (authors)

Video Measurements: Quantity or Quality

Science.gov (United States)

Zajkov, Oliver; Mitrevski, Boce

2012-01-01

Students have problems with understanding, using and interpreting graphs. In order to improve the students' skills for working with graphs, we propose Manual Video Measurement (MVM). In this paper, the MVM method is explained and its accuracy is tested. The comparison with the standardized video data software shows that its accuracy is comparable…

Measuring influenza RNA quantity after prolonged storage or multiple freeze/thaw cycles.

Science.gov (United States)

Granados, Andrea; Petrich, Astrid; McGeer, Allison; Gubbay, Jonathan B

2017-09-01

In this study, we aim to determine what effects prolonged storage and repeated freeze/thaw cycles have on the stability of influenza A(H1N1)pdm09 (influenza A/H1N1)RNA. Cloned influenza A/H1N1 RNA transcripts were serially diluted from 8.0-1.0 log 10 copies/μl. RT-qPCR was used to measure RNA loss in transcripts stored at -80°C, -20°C, 4°C and 25°C for up to 84days or transcripts undergoing a total of 10 freeze/thaw cycles. Viral load was measured in clinical specimens stored at-80°C for three years (n=89 influenza A RNA extracts; n=35 primary specimens) and in 10 clinical specimens from the 2015/2016 influenza season that underwent 7 freeze/thaw cycles. RNA stored at -80°C, -20°C, 4°C and 25°C is stable for up to 56, 56, 21, and 7days respectively or up to 9 freeze/thaw cycles when stored at -80°C. There is no difference in viral load in clinical specimens that have been stored for up to three years at -80°C if they are re-extracted. Similarly, clinical specimens undergoing up to 7 freeze/thaw cycles are stable if they are re-extracted between cycles. Influenza specimens can be stored for up to three years at -80°C or undergo up to 7 freeze/thaw cycles without loss of RNA quantity if re-extracted. Copyright © 2017 Elsevier B.V. All rights reserved.

Electromagnetically controlled measuring device for measuring injection quantities in a diesel injection pump volumetrically. Elektromagnetisch gesteuerte Messvorrichtung zur volumetrischen Messung von Einspritzmengen einer Dieseleinspritzpumpe

Energy Technology Data Exchange (ETDEWEB)

Hoffmann, K H; Mueller, M; Decker, R; Huber, G

1990-11-22

The invention concerns a measuring device for volumetric measurements of injection quantities of a diesel injection pump which injects its contents into a volumetric chamber controlled electromagnetically by a discharge valve and enclosed by a non-impact gas pressure loaded volumetric vessel and effects a retreating movement of the latter. The device is provided with an inductive path controller fitted with a differential pair of coils containing an axially movable ferromagnetic core. The path controller forms a part of a lifter rod connected to the volumetric vessel. It gives an opening signal to the discharge valve after each retreat of the volumetric vessel and a closing signal as soon as a defined height of suspension corresponding to the original position of the volumetric vessel after its return is reached.

Toward new instruments for measurement of low concentration hydrogen sulfide in small-quantity aqueous solutions

International Nuclear Information System (INIS)

Wu, Xiao Chu; Wu, Dong Qing; Zhang, W J; Sammynaiken, R; Yang, Wei; Wang, Rui

2008-01-01

Endogenously generated hydrogen sulfide (H 2 S) has been found to play some important physiological roles in the nervous and cardiovascular systems, such as a neuromodulator and a vasorelaxant. These roles are in contrast to our common perception that H 2 S is toxic. However, whether H 2 S plays a positive or negative role is dependent on the H 2 S concentration levels in mammals. This further puts a high demand on the accurate measurement of H 2 S in mammals with a further desire to be real time, continuous and in vivo. Existing methods for H 2 S measurement require a large number of tissue samples with complex procedures, and these methods are extremely invasive. The development of new in vivo and real-time methods for measuring H 2 S is, however, a great challenge. In the present study, we proposed and examined five potential H 2 S measurement methods: (1) atomic force microscopy with coating materials, (2) Raman spectroscopy on the H 2 S solutions, (3) gas chromatography/mass spectroscopy (with the static headspace technique) on the H 2 S solutions, (4) mass spectroscopy on unfunctionalized carbon nanotubes treated with the H 2 S solutions and (5) Raman spectroscopy on unfunctionalized carbon nanotubes treated with the H 2 S solutions. Our study concluded that method (5) is the most promising one for detecting low concentration H 2 S in small-quantity aqueous solutions in terms of measurement resolution and non-invasiveness, but the method is not very robust

Radiation quantities and units

International Nuclear Information System (INIS)

1980-01-01

This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. In line, with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection 1.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. As in ICRU Report 19, the definitions of quantities and units specifically designed for radiation protection (Part B) are separated from those of the general quantities (Part A). The inclusion of the index concept outlined in ICRU Report 25[4] required an extension of Part B

Determination of micro-quantities of several elements in soil solution by isotope dilution and activation analyses

International Nuclear Information System (INIS)

Cho, C.M.; Axmann, H.

1965-01-01

Determination of small quantities of plant nutrients in the soil solution of flooded rice soils is a difficult problem. The concentrations of Mn, Fe and P, for example, in some soil solutions are so small that no chemical method gives any accurate result. Neutron activation analysis was reported to give a much lower limit of detectability for several elements, while for elements with low-induced activity after neutron irradiation, substoichiometric isotopic dilution analysis was applied. One of the advantages of neutron activation analysis lies in the fact that simultaneous activation of every inducible element in a sample takes place. This gives an opportunity to determine many elements by one sample preparation and irradiation. This, however, is not a simple task since identification of the activated products and their quantitative estimation becomes very difficult. Certain operations of separation must be carried out before activity measurements. Ion-exchange resin columns and chemical separation following the addition of carriers were successfully used for the determination of many elements after neutron irradiation. These procedures, however, cannot be directly applied to the determination of the elements of agronomic interest. A procedure was developed to determine several elements of agronomic interest. Times of irradiation and cooling, quick separation by ion-exchange columns, together with chemical precipitation for β-emitters of relatively long half-lives, were all combined to get the maximum benefit from neutron activation analysis. For Fe, for which no satisfactory neutron activation analysis has yet been developed, a modified substoichiometric double isotope dilution procedure is applied

Validity of the concept of absorbed dose as a physical quantity

International Nuclear Information System (INIS)

Tada, Jun-Ichiro; Katoh, Kazuaki.

1995-01-01

The concept of the 'absorbed dose' of ionizing radiation is scrutinized from physical point of view. It is shown that the concept and definition of the quantity in the ICRU system is disqualified as a physical quantity and the absorbed dose can not always be a 'measure of cause' in describing causality relation between radiation and effects on matter. The current absorbed dose depends even on the energy that have already been brought out from the matter, contrary to the intention of introducing the quantity. Trials to remove these difficulties are made. However, it is also shown there still exists an essential problem that cannot be solved by improving the formulation. (author)

Units for physical quantities used in dosimetry and radiation protection

Energy Technology Data Exchange (ETDEWEB)

Taubert, R; Wagner, S

1976-04-01

The 15th General Conference on Weights and Measures (1975) decided to introduce the name Becquerel for the SI unit of the quantity activity (1 Bq = 1 s/sup -1/) and the name Gray for the SI unit of ionizing radiations (1 Gy = 1 J/kg). The consequences of this latter decision are discussed. The Bundesanstalt is of the opinion that no further names for this unit should be introduced, but that the Gray should be used also for other quantities of the same dimension, especially for the dose equivalent.

Analyses of Environmental Impacts of Non Hazardous Regional Landfills in Macedonia

Directory of Open Access Journals (Sweden)

Katerina Donevska

2013-12-01

Full Text Available This paper presents an assessment of potential environmental impacts for eight planned non-hazardous regional landfills in Macedonia. Waste quantities for each waste management region and landfill capacities are estimated. Expected leachate quantities are calculated using Water Balance Method. Analyses and comparison of the likely landfill leachate per capita are presented, demonstrating that higher rates of leachate are generated per capita in waste management regions with higher annual sums of rainfall. An assessment of the potential landfill impacts on the water environment taking into consideration local geology and hydrogeology conditions is presented. Some general measures for leachate treatment that are in compliance with the modern EU standards are indicated. The goal of the study is to facilitate a better understanding about the sustainable waste management practices in cases of landfilling of municipal solid waste.

Quality and quantity: the role of social interactions in individual health

OpenAIRE

Damiano, Fiorillo; Fabio, Sabatini

2011-01-01

The public health literature focusing on the detrimental effects of social isolation has shown that the quantity of social connections is positively correlated with individual health. Drawing on pooled cross-sectional data, we test this hypothesis on a representative sample of the Italian population. Our findings show that, besides the quantity of interactions, it is their quality – as measured by subjective satisfaction derived from relationships with friends – that works as the best pre...

Net present value analysis of the economic production quantity

OpenAIRE

Disney, Stephen Michael; Warburton, R. D. H.; Zhong, Q. C.

2013-01-01

Using Laplace transforms we extend the economic production quantity (EPQ) model by analysing cash flows from a net present value (NPV) viewpoint. We obtain an exact expression for the present value of the cash flows in the EPQ problem. From this, we are able to derive the optimal batch size. We obtain insights into the monotonicity and convexity of the present value of each of the cash flows, and show that there is a unique minimum in the present value of the sum of the cash flows in the exte...

Terms and definitions in the field of radiological technique. Dose quantities and units

International Nuclear Information System (INIS)

1985-12-01

The standard gives the terms and definitions of concepts, dose quantities and units. The radiation field condition 'secondary electron equilibrium', which forms part of the definition of standard ion dose, is given more precisely. The term 'free in air' is used in its original meaning, i.e. characterization of measuring conditions excluding avoidable stray radiation, which deviates from DIN 6814, part 3/06.72. Dosemeters for measurement of standard ion dose of air kerma are calibrated 'free in air', but this calibration condition is not part of the quantity definition. The quantities standard ion dose or air kerma therefore can also be measured in any other material. The qunatitative relationships between standard ion dose and the quantities 'exposure' and air kerma, as given in the ICRU publication 33 'Quantities and Units' (1980), are explained. The standard introduces the SI units Gray (for energy dose), Sievert (for dose equivalent), and Becquerel (for the activity of a radioactive substance). As the change to the SI units conceals the approximated equality of the numerical values of the standrd ion dose of photon radiation in roentgen, of the energy dose for soft tissue in rad, and of the dose equivalent in rem, new definitions are given in accordance with ICRU 33 for the quantities specified dose rate, dose rate constant, and area exposure product. These definitions use the terms 'energy dose' and 'kerma'. The dose concepts applied in the field of radiation protection, especially ambient dose and individual dose, are defined as dose equivalents in compliance with the Radiation Protection Ordinance. The relevant sections present information on the conversion of standard ion dose values to the corresponding values of kerma, energy dose, or dose equivalent. (orig./HP) [de

MASER: Measuring, Analysing, Simulating low frequency Radio Emissions.

Science.gov (United States)

Cecconi, B.; Le Sidaner, P.; Savalle, R.; Bonnin, X.; Zarka, P. M.; Louis, C.; Coffre, A.; Lamy, L.; Denis, L.; Griessmeier, J. M.; Faden, J.; Piker, C.; André, N.; Genot, V. N.; Erard, S.; King, T. A.; Mafi, J. N.; Sharlow, M.; Sky, J.; Demleitner, M.

2017-12-01

The MASER (Measuring, Analysing and Simulating Radio Emissions) project provides a comprehensive infrastructure dedicated to low frequency radio emissions (typically Radioastronomie de Nançay and the CDPP deep archive. These datasets include Cassini/RPWS, STEREO/Waves, WIND/Waves, Ulysses/URAP, ISEE3/SBH, Voyager/PRA, Nançay Decameter Array (Routine, NewRoutine, JunoN), RadioJove archive, swedish Viking mission, Interball/POLRAD... MASER also includes a Python software library for reading raw data.

Social Media Analyses for Social Measurement

Science.gov (United States)

Schober, Michael F.; Pasek, Josh; Guggenheim, Lauren; Lampe, Cliff; Conrad, Frederick G.

2016-01-01

Demonstrations that analyses of social media content can align with measurement from sample surveys have raised the question of whether survey research can be supplemented or even replaced with less costly and burdensome data mining of already-existing or “found” social media content. But just how trustworthy such measurement can be—say, to replace official statistics—is unknown. Survey researchers and data scientists approach key questions from starting assumptions and analytic traditions that differ on, for example, the need for representative samples drawn from frames that fully cover the population. New conversations between these scholarly communities are needed to understand the potential points of alignment and non-alignment. Across these approaches, there are major differences in (a) how participants (survey respondents and social media posters) understand the activity they are engaged in; (b) the nature of the data produced by survey responses and social media posts, and the inferences that are legitimate given the data; and (c) practical and ethical considerations surrounding the use of the data. Estimates are likely to align to differing degrees depending on the research topic and the populations under consideration, the particular features of the surveys and social media sites involved, and the analytic techniques for extracting opinions and experiences from social media. Traditional population coverage may not be required for social media content to effectively predict social phenomena to the extent that social media content distills or summarizes broader conversations that are also measured by surveys. PMID:27257310

Social Media Analyses for Social Measurement.

Science.gov (United States)

Schober, Michael F; Pasek, Josh; Guggenheim, Lauren; Lampe, Cliff; Conrad, Frederick G

2016-01-01

Demonstrations that analyses of social media content can align with measurement from sample surveys have raised the question of whether survey research can be supplemented or even replaced with less costly and burdensome data mining of already-existing or "found" social media content. But just how trustworthy such measurement can be-say, to replace official statistics-is unknown. Survey researchers and data scientists approach key questions from starting assumptions and analytic traditions that differ on, for example, the need for representative samples drawn from frames that fully cover the population. New conversations between these scholarly communities are needed to understand the potential points of alignment and non-alignment. Across these approaches, there are major differences in (a) how participants (survey respondents and social media posters) understand the activity they are engaged in; (b) the nature of the data produced by survey responses and social media posts, and the inferences that are legitimate given the data; and (c) practical and ethical considerations surrounding the use of the data. Estimates are likely to align to differing degrees depending on the research topic and the populations under consideration, the particular features of the surveys and social media sites involved, and the analytic techniques for extracting opinions and experiences from social media. Traditional population coverage may not be required for social media content to effectively predict social phenomena to the extent that social media content distills or summarizes broader conversations that are also measured by surveys.

Using Inequality Measures to Incorporate Environmental Justice into Regulatory Analyses

Science.gov (United States)

Abstract: Formally evaluating how specific policy measures influence environmental justice is challenging, especially in the context of regulatory analyses in which quantitative comparisons are the norm. However, there is a large literature on developing and applying quantitative...

Long-term integrated river basin planning and management of water quantity and water quality in mining impacted catchments

Science.gov (United States)

Pohle, Ina; Zimmermann, Kai; Claus, Thomas; Koch, Hagen; Gädeke, Anne; Uhlmann, Wilfried; Kaltofen, Michael; Müller, Fabian; Redetzky, Michael; Schramm, Martina; Schoenheinz, Dagmar; Grünewald, Uwe

2015-04-01

water quality model GGM (mining related water quality parameters of lakes and river reaches). Based on the STAR 0K scenario, only minor changes in the natural water balance are simulated, while managed discharges slightly decrease due to declining mining discharges. In the STAR 2K scenario natural and managed discharges decrease resulting in negative consequences on reservoir volumes and on water availability to the users. Additionally, the risk of a re-acidification of mining lakes and increasing sulphate and iron concentrations is much higher in the STAR 2K scenario than in the STAR 0K scenario. In order to compensate for negative impacts on water quantity and water quality, adaptation measures were analysed. While water transfers from the River Elbe into the study region showed positive impacts on both, water quantity and water quality, potentially negative impacts on water quality can also be compensated by technical measures (e.g. in-lake-neutralisation of mining lakes).

Climate Prediction Center (CPC) US daily temperature analyses

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The U.S. daily temperature analyses are maps depicting various temperature quantities utilizing daily maximum and minimum temperature data across the US. Maps are...

Methodological challenges in carbohydrate analyses

Directory of Open Access Journals (Sweden)

Mary Beth Hall

2007-07-01

Full Text Available Carbohydrates can provide up to 80% of the dry matter in animal diets, yet their specific evaluation for research and diet formulation is only now becoming a focus in the animal sciences. Partitioning of dietary carbohydrates for nutritional purposes should reflect differences in digestion and fermentation characteristics and effects on animal performance. Key challenges to designating nutritionally important carbohydrate fractions include classifying the carbohydrates in terms of nutritional characteristics, and selecting analytical methods that describe the desired fraction. The relative lack of information on digestion characteristics of various carbohydrates and their interactions with other fractions in diets means that fractions will not soon be perfectly established. Developing a system of carbohydrate analysis that could be used across animal species could enhance the utility of analyses and amount of data we can obtain on dietary effects of carbohydrates. Based on quantities present in diets and apparent effects on animal performance, some nutritionally important classes of carbohydrates that may be valuable to measure include sugars, starch, fructans, insoluble fiber, and soluble fiber. Essential to selection of methods for these fractions is agreement on precisely what carbohydrates should be included in each. Each of these fractions has analyses that could potentially be used to measure them, but most of the available methods have weaknesses that must be evaluated to see if they are fatal and the assay is unusable, or if the assay still may be made workable. Factors we must consider as we seek to analyze carbohydrates to describe diets: Does the assay accurately measure the desired fraction? Is the assay for research, regulatory, or field use (affects considerations of acceptable costs and throughput? What are acceptable accuracy and variability of measures? Is the assay robust (enhances accuracy of values? For some carbohydrates, we

Emission sources and quantities

International Nuclear Information System (INIS)

Heinen, B.

1991-01-01

The paper examines emission sources and quantities for SO 2 and NO x . Natural SO 2 is released from volcanic sources and to a much lower extent from marsh gases. In nature NO x is mainly produced in the course of the chemical and bacterial denitrification processes going on in the soil. Manmade pollutants are produced in combustion processes. The paper concentrates on manmade pollution. Aspects discussed include: mechanism of pollution development; manmade emission sources (e.g. industry, traffic, power plants and domestic sources); and emission quantities and forecasts. 11 refs., 2 figs., 5 tabs

Prognosis of radioactive wastes quantity in soils of new safety confinement foundation area

International Nuclear Information System (INIS)

Klyuchnikov, A.A.; Panasyuk, N.I.; Podbereznyj, S.S.; Skorbun, A.D.; Levin, G.V. and eds.

2006-01-01

or the first time a scientific founded calculation of radioactive wastes (radioactive soils) quantities at the places of New Safety Confinement foundation building has been given, and a map of bedding is shown. An example of construction of geoinformation system, created using ArcGIS 8.3 for analysing of soils radioactive contamination in the 'Ukryttya' object area of Chernobyl NPP have been examined

EFFECT OF SALES PROMOTION SCHEMES ON PURCHASE QUANTITY: A STUDY OF MALAYSIAN CONSUMERS

Directory of Open Access Journals (Sweden)

Hawa JALLOW

2016-11-01

Full Text Available The research aims to study the effect of sales promotion on the purchase quantity and recommend sales promotional means and methods that could improve sales for retail sector in Malaysia. The impact of coupons, bonus packages, premiums, free samples and price discount is measured on purchase quantity of Malaysian retail consumers. Empirical data is gathered from 150 respondents using self-administered questionnaire and analyzed using correlation and regression analysis to examine the relationship between variables. The findings of the study reveal that all independent variables influences purchase quantity positively and significantly while free samples and price discounts are most influential factors for Malaysian market.

The effect of coolant quantity on local fuel–coolant interactions in a molten pool

International Nuclear Information System (INIS)

Cheng, Songbai; Matsuba, Ken-ichi; Isozaki, Mikio; Kamiyama, Kenji; Suzuki, Tohru; Tobita, Yoshiharu

2015-01-01

Highlights: • We investigate local fuel–coolant interactions in a molten pool. • As water volume increases, limited pressurization and mechanical energy observed. • Only a part of water is evaporated and responsible for the pressurization. - Abstract: Studies on local fuel–coolant interactions (FCI) in a molten pool are important for severe accident analyses of sodium-cooled fast reactors (SFRs). Motivated by providing some evidence for understanding this interaction, in this study several experimental tests, with comparatively larger difference in coolant volumes, were conducted by delivering a given quantity of water into a simulated molten fuel pool (formed with a low-melting-point alloy). Interaction characteristics including the pressure-buildup as well as mechanical energy release and its conversion efficiency are evaluated and compared. It is found that as water quantity increases, a limited pressure-buildup and the resultant mechanical energy release are observable. The performed analyses also suggest that only a part of water is probably vaporized during local FCIs and responsible for the pressurization and mechanical energy release, especially for those cases with much larger water volumes

Method of Converting Wheat Flour Quantity into Rice Flour Quantity in Cookies (Part-1)

OpenAIRE

村田,美穂子; 髙橋,由加

2016-01-01

A method of converting the wheat flour quantity of a recipe of wheat-flour cookies into the rice flour quantity of a recipe of rice-flour cookies used domestically for wheat-allergic children was studied. The proportion of the water content with respect to the flour content (the wheat or rice flour content) in cut cookies prepared according to a commercially available recipe was obtained. Next, four types of rice-flour cookies were prepared according to a recipe for wheat-flour cookies using ...

Measurement and analysis of radioactive substances; Mesure et analyse de substances radioactives

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

Here are gathered the abstracts presented to the 3. summer university of the year 2001 whose main themes were the destructive (5 conferences) and nondestructive (8 conferences) analyses applied to nuclear industry. The points of view of different organisms (as DSIN: Directorate for the Safety of Nuclear Installations, IPSN: Institute of Nuclear Protection and Safety, OPRI: Office of Protection against Ionizing Radiations, TUI: Institute for Transuranium Elements, COGEMA, EDF: Electric Utilities, ANDRA: French National Agency for Radioactive Waste Management, CRLC Val d'Aurelle, France) concerning the needs involved in nuclear facilities control, the methods of radionuclide speciation in use internationally, the measurements and analyses of radioactive substances are given too as well as some general concepts concerning 1)the laser-matter interaction 2)the ions production 3)the quality applied to the measurements and analyses 4)the standard in activity metrology. (O.M.)

Antepartum depression severity is increased during seasonally longer nights: relationship to melatonin and cortisol timing and quantity.

Science.gov (United States)

Meliska, Charles J; Martínez, Luis F; López, Ana M; Sorenson, Diane L; Nowakowski, Sara; Kripke, Daniel F; Elliott, Jeffrey; Parry, Barbara L

2013-11-01

Current research suggests that mood varies from season to season in some individuals, in conjunction with light-modulated alterations in chronobiologic indices such as melatonin and cortisol. The primary aim of this study was to evaluate the effects of seasonal variations in darkness on mood in depressed antepartum women, and to determine the relationship of seasonal mood variations to contemporaneous blood melatonin and cortisol measures; a secondary aim was to evaluate the influence of seasonal factors on measures of melancholic versus atypical depressive symptoms. We obtained measures of mood and overnight concentrations of plasma melatonin and serum cortisol in 19 depressed patients (DP) and 12 healthy control (HC) antepartum women, during on-going seasonal variations in daylight/darkness, in a cross-sectional design. Analyses of variance showed that in DP, but not HC, Hamilton Depression Rating Scale (HRSD) scores were significantly higher in women tested during seasonally longer versus shorter nights. This exacerbation of depressive symptoms occurred when the dim light melatonin onset, the melatonin synthesis offset, and the time of maximum cortisol secretion (acrophase) were phase-advanced (temporally shifted earlier), and melatonin quantity was reduced, in DP but not HC. Serum cortisol increased across gestational weeks in both the HC and DP groups, which did not differ significantly in cortisol concentration. Nevertheless, serum cortisol concentration correlated positively with HRSD score in DP but not HC; notably, HC showed neither significant mood changes nor altered melatonin and cortisol timing or quantity in association with seasonal variations. These findings suggest that depression severity during pregnancy may become elevated in association with seasonally related phase advances in melatonin and cortisol timing and reduced melatonin quantity that occur in DP, but not HC. Thus, women who experience antepartum depression may be more susceptible than

The new operational quantities for radiation protection

International Nuclear Information System (INIS)

Kellerer, A.M.

1985-01-01

Philosophies and quantities for radiation protection have often been subjected to changes, and some of the developments are traced which ultimately led to recent proposals by ICRU. Development in the past has largely been towards clarification and generalisation of definitions. The present changes, however, reflect a more fundamental issue, the transition from the limitation system to the assessment system in radiation protection. The index quantities were suitable tools to ascertain compliance with the limitation system of radiation protection. The new quantities proposed by ICRU are suitable estimators for effective dose equivalent, which is an essential quantity in the assessment system of radiation protection. A synopsis of the definitions is given. (author)

Measurements and analyses of cosmic-ray exposure rates perturbed by various environmental objects

International Nuclear Information System (INIS)

Fukaya, Mitsuharu; Minato, Susumu

1988-01-01

One-dimensional intensity distributions of cosmic-rays transmitted through various large structural objects were measured to examine the feasibility of 'cosmic-ray radiography'. 1) For the rectungular building, (a) the bulk density estimation by comparison of the observed distribution with the calculated one, and (b) edge detection by differential method, were found to be possible. 2) For the stairs in the subway station, the relation between the intensities and the stairs depths was able to be interpreted by a simple model. These findings indicate that it is possible to correlate transmitted cosmic-ray intensity distributions to the structure and/or the physical quantities of large structural objects. (author)

36 CFR 223.220 - Quantity determination.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Quantity determination. 223.220 Section 223.220 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER Special Forest Products § 223.220 Quantity determination...

Adolescent computer use and alcohol use: what are the role of quantity and content of computer use?

Science.gov (United States)

Epstein, Jennifer A

2011-05-01

The purpose of this study was to examine the relationship between computer use and alcohol use among adolescents. In particular, the goal of the research was to determine the role of lifetime drinking and past month drinking on quantity as measured by amount of time on the computer (for school work and excluding school work) and on content as measured by the frequency of a variety of activities on the internet (e.g., e-mail, searching for information, social networking, listen to/download music). Participants (aged 13-17 years and residing in the United States) were recruited via the internet to complete an anonymous survey online using a popular survey tool (N=270). Their average age was 16 and the sample was predominantly female (63% girls). A series of analyses was conducted with the computer use measures as dependent variables (hours on the computer per week for school work and excluding school work; various internet activities including e-mail, searching for information, social networking, listen to/download music) controlling for gender, age, academic performance and age of first computer use. Based on the results, past month drinkers used the computer more hours per week excluding school work than those who did not. As expected, there were no differences in hours based on alcohol use for computer use for school work. Drinking also had relationships with more frequent social networking and listening to/downloading music. These findings suggest that both quantity and content of computer use were related to adolescent drinking. Copyright © 2010 Elsevier Ltd. All rights reserved.

Event group importance measures for top event frequency analyses

International Nuclear Information System (INIS)

1995-01-01

Three traditional importance measures, risk reduction, partial derivative, nd variance reduction, have been extended to permit analyses of the relative importance of groups of underlying failure rates to the frequencies of resulting top events. The partial derivative importance measure was extended by assessing the contribution of a group of events to the gradient of the top event frequency. Given the moments of the distributions that characterize the uncertainties in the underlying failure rates, the expectation values of the top event frequency, its variance, and all of the new group importance measures can be quantified exactly for two familiar cases: (1) when all underlying failure rates are presumed independent, and (2) when pairs of failure rates based on common data are treated as being equal (totally correlated). In these cases, the new importance measures, which can also be applied to assess the importance of individual events, obviate the need for Monte Carlo sampling. The event group importance measures are illustrated using a small example problem and demonstrated by applications made as part of a major reactor facility risk assessment. These illustrations and applications indicate both the utility and the versatility of the event group importance measures

Event group importance measures for top event frequency analyses

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-31

Three traditional importance measures, risk reduction, partial derivative, nd variance reduction, have been extended to permit analyses of the relative importance of groups of underlying failure rates to the frequencies of resulting top events. The partial derivative importance measure was extended by assessing the contribution of a group of events to the gradient of the top event frequency. Given the moments of the distributions that characterize the uncertainties in the underlying failure rates, the expectation values of the top event frequency, its variance, and all of the new group importance measures can be quantified exactly for two familiar cases: (1) when all underlying failure rates are presumed independent, and (2) when pairs of failure rates based on common data are treated as being equal (totally correlated). In these cases, the new importance measures, which can also be applied to assess the importance of individual events, obviate the need for Monte Carlo sampling. The event group importance measures are illustrated using a small example problem and demonstrated by applications made as part of a major reactor facility risk assessment. These illustrations and applications indicate both the utility and the versatility of the event group importance measures.

Two-dimensional Kikuchi patterns of Si as measured using an electrostatic analyser

Energy Technology Data Exchange (ETDEWEB)

Vos, Maarten, E-mail: maarten.vos@anu.edu.au [Electronic Materials Engineering Department, Research School of Physics and Engineering, The Australian National University, Canberra 2601 (Australia); Winkelmann, Aimo [Bruker Nano GmbH, Am Studio 2D, Berlin 12489 (Germany)

2016-12-15

We present Kikuchi patterns of Si single crystals measured with an electrostatic analyser, where the kinetic energy of the diffracted electron is known with sub-eV precision. Two-dimensional patterns are acquired by rotating the crystal under computer control. This makes detailed comparison of calculated and measured distributions possible with precise knowledge of the energy of the scattered electrons. The case of Si is used to validate the method, and these experiments provide a detailed comparison of measured and calculated Kikuchi patterns. In this way, we can gain more insight on Kikuchi pattern formation in non-energy resolved measurements of conventional electron backscatter diffraction (EBSD) and electron channeling patterns (ECP). It was possible to identify the influence of channeling of the incoming beam on the measured Kikuchi pattern. The effect of energy loss on the Kikuchi pattern was established, and it is demonstrated that, under certain conditions, the channeling features have a different dependence on the energy loss compared to the Kikuchi lines. - Highlights: • Two-dimensional Kikuchi patterns measured for Silicon with electrostatic analyser. • Good agreement obtained with dynamical theory of diffraction. • Channeling effects of the incoming beam are identified.

Implementing and Characterizing Precise Multiqubit Measurements

Directory of Open Access Journals (Sweden)

J. Z. Blumoff

2016-09-01

Full Text Available There are two general requirements to harness the computational power of quantum mechanics: the ability to manipulate the evolution of an isolated system and the ability to faithfully extract information from it. Quantum error correction and simulation often make a more exacting demand: the ability to perform nondestructive measurements of specific correlations within that system. We realize such measurements by employing a protocol adapted from Nigg and Girvin [Phys. Rev. Lett. 110, 243604 (2013], enabling real-time selection of arbitrary register-wide Pauli operators. Our implementation consists of a simple circuit quantum electrodynamics module of four highly coherent 3D transmon qubits, collectively coupled to a high-Q superconducting microwave cavity. As a demonstration, we enact all seven nontrivial subset-parity measurements on our three-qubit register. For each, we fully characterize the realized measurement by analyzing the detector (observable operators via quantum detector tomography and by analyzing the quantum backaction via conditioned process tomography. No single quantity completely encapsulates the performance of a measurement, and standard figures of merit have not yet emerged. Accordingly, we consider several new fidelity measures for both the detector and the complete measurement process. We measure all of these quantities and report high fidelities, indicating that we are measuring the desired quantities precisely and that the measurements are highly nondemolition. We further show that both results are improved significantly by an additional error-heralding measurement. The analyses we present here form a useful basis for the future characterization and validation of quantum measurements, anticipating the demands of emerging quantum technologies.

Statistical Analysis of the Impact of Wind Power on Market Quantities and Power Flows

DEFF Research Database (Denmark)

Pinson, Pierre; Jónsson, Tryggvi; Zugno, Marco

2012-01-01

In view of the increasing penetration of wind power in a number of power systems and markets worldwide, we discuss some of the impacts that wind energy may have on market quantities and cross-border power flows. These impacts are uncovered through statistical analyses of actual market and flow data...... of load and wind power forecasts on Danish and German electricity markets....

Would more social partners leads to enhanced health? The paradox between quantity and quality.

Science.gov (United States)

Xing, Cai; Zhang, Xin; Cheng, Sheung-Tak

2017-09-01

In the current investigation, we examined the association between social network composition (SNC) and mental health, as well as whether quantity and quality of social network could influence mental health differently. The social network quantity and quality of 345 middle-aged and older Chinese adults were measured by the Social Convoy Questionnaire. The Chinese version of the Medical Outcome Studies 36-item Short-Form Health Survey (SF-36) was used to assess mental health while controlling for physical health. It was found that both quantity and quality of social network were associated with mental health, and more specifically that (1) quantity of peripheral partners (PP) was positively associated with mental health; (2) quality of emotionally close social partners (ECSP) influenced mental health the most; and (3) paradoxically, the effect of ECSP quality on mental health depended on quantity of ECSP, that is, participants with more ECSP showed a stronger association between ECSP quality and mental health. The findings replicated and extended previous studies on SNC and suggested that structure/quantity and quality of SNC were both important for mental health. © 2017 The Institute of Psychology, Chinese Academy of Sciences and John Wiley & Sons Australia, Ltd.

Exercise quantity-dependent muscle hypertrophy in adult zebrafish (Danio rerio).

Science.gov (United States)

Hasumura, Takahiro; Meguro, Shinichi

2016-07-01

Exercise is very important for maintaining and increasing skeletal muscle mass, and is particularly important to prevent and care for sarcopenia and muscle disuse atrophy. However, the dose-response relationship between exercise quantity, duration/day, and overall duration and muscle mass is poorly understood. Therefore, we investigated the effect of exercise duration on skeletal muscle to reveal the relationship between exercise quantity and muscle hypertrophy in zebrafish forced to exercise. Adult male zebrafish were exercised 6 h/day for 4 weeks, 6 h/day for 2 weeks, or 3 h/day for 2 weeks. Flow velocity was adjusted to maximum velocity during continual swimming (initial 43 cm/s). High-speed consecutive photographs revealed that zebrafish mainly drove the caudal part. Additionally, X-ray micro computed tomography measurements indicated muscle hypertrophy of the mid-caudal half compared with the mid-cranial half part. The cross-sectional analysis of the mid-caudal half muscle revealed that skeletal muscle (red, white, or total) mass increased with increasing exercise quantity, whereas that of white muscle and total muscle increased only under the maximum exercise load condition of 6 h/day for 4 weeks. Additionally, the muscle fiver size distributions of exercised fish were larger than those from non-exercised fish. We revealed that exercise quantity, duration/day, and overall duration were correlated with skeletal muscle hypertrophy. The forced exercise model enabled us to investigate the relationship between exercise quantity and skeletal muscle mass. These results open up the possibility for further investigations on the effects of exercise on skeletal muscle in adult zebrafish.

Quantifying cannabis: A field study of marijuana quantity estimation.

Science.gov (United States)

Prince, Mark A; Conner, Bradley T; Pearson, Matthew R

2018-05-17

The assessment of marijuana use quantity poses unique challenges. These challenges have limited research efforts on quantity assessments. However, quantity estimates are critical to detecting associations between marijuana use and outcomes. We examined accuracy of marijuana users' estimations of quantities of marijuana they prepared to ingest and predictors of both how much was prepared for a single dose and the degree of (in)accuracy of participants' estimates. We recruited a sample of 128 regular-to-heavy marijuana users for a field study wherein they prepared and estimated quantities of marijuana flower in a joint or a bowl as well as marijuana concentrate using a dab tool. The vast majority of participants overestimated the quantity of marijuana that they used in their preparations. We failed to find robust predictors of estimation accuracy. Self-reported quantity estimates are inaccurate, which has implications for studying the link between quantity and marijuana use outcomes. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

30 CFR 75.325 - Air quantity.

Science.gov (United States)

2010-07-01

... the exposure of miners. (i) A ventilating air quantity that is less than what is required by paragraph... results of sampling that demonstrate that the lesser air quantity will maintain continuous compliance with applicable TLV ®'s. (j) If during sampling required by § 70.1900(c) of this subchapter the ventilating air is...

Dose rate constants for new dose quantities

International Nuclear Information System (INIS)

Tschurlovits, M.; Daverda, G.; Leitner, A.

1992-01-01

Conceptual changes and new quantities made is necessary to reassess dose rate quantities. Calculations of the dose rate constant were done for air kerma, ambient dose equivalent and directional dose equivalent. The number of radionuclides is more than 200. The threshold energy is selected as 20 keV for the dose equivalent constants. The dose rate constant for the photon equivalent dose as used mainly in German speaking countries as a temporary quantity is also included. (Author)

Are Quantity Surveyors Competent to Value for Civil Engineering Works? Evaluating QSs' Competencies and Militating Factors

Science.gov (United States)

Olawumi, Timothy Oluwatosin; Ayegun, Olaleke Amos

2016-01-01

The role of the quantity surveyor is one that is often unclear amongst the general public. This study discussed the competencies of the quantity surveyor in measuring and managing civil engineering works and also carrying out the financial management for civil engineering construction projects; also outlined the various competencies and skills…

7 CFR 61.102 - Determination of quantity index.

Science.gov (United States)

2010-01-01

... the quantity index shall equal four times percentage of oil plus six times percentage of ammonia, plus 5. (b) For American Pima cottonseed the quantity index shall equal four times percentage of oil... 7 Agriculture 3 2010-01-01 2010-01-01 false Determination of quantity index. 61.102 Section 61.102...

The Acquisition of Quantity Contrasts in Guina-ang Bontok

Science.gov (United States)

Aoyama, Katsura; Reid, Lawrence A.

2016-01-01

This study reports on the acquisition of quantity contrasts in Guina-ang Bontok, an indigenous language spoken in the Philippines. Four-year-old and 5-year-old children's perception and production of quantity contrasts were examined using a pair of names that contrast in the quantity of the medial nasal. Frequencies of the quantity contrast were…

Determinants of procurement strategy for construction works: quantity surveyors’ perspectives

Directory of Open Access Journals (Sweden)

Olanrewaju AbdulLateef

2016-01-01

Full Text Available The selection of the ‘appropriate’ procurement strategy is a prerequisite to the success or failure of a construction project. This paper investigates the factors determining the selection of appropriate procurement strategy for construction works in Nigeria. Data for the study was collected through an online survey questionnaire. The survey administration involves only quantity surveyors. Quantity surveyors were targeted because they advise clients and other stakeholders on procurement and contractual issues on construction works. A total of 33 usable responses were received and analysed for this study. On the basis of the results, it is concluded that the selection of procurement strategies for construction depend on complex interrelated factors. The study could not detect a particular factor or few factors responsible for a procurement strategy selection. The findings of this study is useful because it argues that the construction sector needs to broaden its considerations on the procurement strategy’s determinants rather than focusing solely on the client’s type and nature of projects as is often cited. Future research could segment these factors in terms of class of construction works or increase the sample size, which might lead to different findings.

Destructive and non-destructive methods of measuring the quantity and isotopic composition of fissile materials for purposes of national safeguards in the German Democratic Republic

International Nuclear Information System (INIS)

Villun, K.; Gruner, V.; Siebert, Kh.U.; Hoffmann, D.

1979-01-01

The authors give a brief description of the destructive and non-destructive methods of measuring the quantity and isotopic composition of fissile materials used in the nuclear materials accounting and control system of the German Democratic Republic. They cite examples of the use of gamma-spectrometry, X-ray fluorescence analysis, neutron activation, radiochemical techniques, mass-spectrometry and alpha-spectrometry. (author)

A portable analyser for the measurement of ammonium in marine waters.

Science.gov (United States)

Amornthammarong, Natchanon; Zhang, Jia-Zhong; Ortner, Peter B; Stamates, Jack; Shoemaker, Michael; Kindel, Michael W

2013-03-01

A portable ammonium analyser was developed and used to measure in situ ammonium in the marine environment. The analyser incorporates an improved LED photodiode-based fluorescence detector (LPFD). This system is more sensitive and considerably smaller than previous systems and incorporates a pre-filtering subsystem enabling measurements in turbid, sediment-laden waters. Over the typical range for ammonium in marine waters (0–10 mM), the response is linear (r(2) = 0.9930) with a limit of detection (S/N ratio > 3) of 10 nM. The working range for marine waters is 0.05–10 mM. Repeatability is 0.3% (n =10) at an ammonium level of 2 mM. Results from automated operation in 15 min cycles over 16 days had good overall precision (RSD = 3%, n = 660). The system was field tested at three shallow South Florida sites. Diurnal cycles and possibly a tidal influence were expressed in the concentration variability observed.

Memory-Based Quantity Discrimination in Coyotes (Canis latrans

Directory of Open Access Journals (Sweden)

Salif Mahamane

2014-08-01

Full Text Available Previous research has shown that the ratio between competing quantities of food significantly mediates coyotes‘ (Canis latrans ability to choose the larger of two food options. These previous findings are consistent with predictions made by Weber‘s Law and indicate that coyotes possess quantity discrimination abilities that are similar to other species. Importantly, coyotes‘ discrimination abilities are similar to domestic dogs (Canis lupus familiaris, indicating that quantitative discrimination may remain stable throughout certain species‘ evolution. However, while previously shown in two domestic dogs, it is unknown whether coyotes possess the ability to discriminate visual quantities from memory. Here, we address this question by displaying different ratios of food quantities to 14 coyotes before placing the choices out of sight. The coyotes were then allowed to select one of either non-visible food quantities. Coyotes‘ discrimination of quantity from memory does not follow Weber‘s Law in this particular task. These results suggest that working memory in coyotes may not be adapted to maintain information regarding quantity as well as in domestic dogs. The likelihood of a coyote‘s choosing the large option increased when it was presented with difficult ratios of food options first, before it was later presented with trials using more easily discriminable ratios, and when the large option was placed on one particular side. This suggests that learning or motivation increased across trials when coyotes experienced difficult ratios first, and that location of food may have been more salient in working memory than quantity of food.

21 CFR 201.51 - Declaration of net quantity of contents.

Science.gov (United States)

2010-04-01

... augmented to give the weight or measure of the drug units or the quantity of each active ingredient in each... an active ingredient in a unit of a drug. (d) The declaration shall appear as a distinct item on the.... In the case of a liquid drug in ampules or vials, intended for injection, the declaration shall be...

Quantities used in radiological protection

International Nuclear Information System (INIS)

Menossi, Carlos

2010-01-01

The application of ICRP recommendations requires knowledge of a variety of concepts and magnitudes. Many of them are employed in other fields of science and precision in its definition reflects this wide application. In this regard, information on quantities and basic units of radiation, which exists in numerous publications, are subjects of great interest. The characteristics and radiation effects are studied by physicists, biologists and chemists mainly. However, there are basics that must be known and to be recognized by general practitioners and specialists from all branches of medicine. The information on quantities and units are used only in radiation protection, have been obtained from the reports listed on the attached bibliography. Such quantities and units contain weighting factors used to provide for different types of radiation and energies that affect the body and thus take into account the relative radio-sensitivity of different tissues. Additionally, they have added a series of data for a better understanding of the units: for example, multiples and sub-multiples, and some examples of converting the units used in radiation protection. (author) [es

Effect of maca supplementation on bovine sperm quantity and quality followed over two spermatogenic cycles.

Science.gov (United States)

Clément, C; Kneubühler, J; Urwyler, A; Witschi, U; Kreuzer, M

2010-07-15

Maca (Lepidium meyenii Walpers), is an Andean crop that grows between 3,800 and 4,500 m a.s.l. The persistent interest in this plant is based on its assumed effects on fertility of male mammals due to the prevalence of certain, partially specific, secondary compounds. The present study aimed at evaluating the effect of maca supplementation on quality and quantity of semen, mating behavior, and clinical status of peripubertal breeding bulls. The experiment followed a cross-over design lasting for 23 wk with 3 wk of adaptation and baseline measurements, and 2 x 10 wk of treatment feeding thus covering two times the complete 8-wk spermatogenic cycle. Seventy-eight 55 wk to 84 wk old breeding bulls received either no maca (control) or maca (233 mg dried hypocotyls/kg body weight/day) for 10 wk followed by 10 wk without maca (maca early) or maca only in the last 10 wk (maca late). Measurements were always made in the last 2 wk of each period. Apart from standard analyses, ejaculates were analyzed by flow cytometry. Data was evaluated by analysis of variance considering the repeated measurement structure of the data. Significant treatment by measurement period indicated direct or carry-over effects of maca. Maca supplementation had no direct effect on body weight, testes circumference, rectal temperature, mating behavior, and ejaculate volume. However, supplementing maca in the first 10 wk period increased the number of sperms in the second 10 wk period, i.e., when the animals no longer received maca. The DNA fragmentation index and the visually assessed motility of the sperms of bulls, that initially showed a borderline sperm quality, were significantly improved with early maca supplementation, while no such effect was observed in the two other groups. No effects occurred in the proportion of intact sperm plasma membranes or acrosomes or both. In conclusion, maca supplementation seems to improve sperm quantity and quality of bulls to a certain degree, while mating

48 CFR 916.504 - Indefinite-quantity contracts.

Science.gov (United States)

2010-10-01

... indefinite-quantity, multiple award contracts to ensure that adequate consideration exists to contractually... contracts. 916.504 Section 916.504 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CONTRACTING METHODS AND CONTRACT TYPES TYPES OF CONTRACTS Indefinite-Delivery Contracts 916.504 Indefinite-quantity...

The experimental determination of the relationship between the energising time of the common rail injector and the set fuel quantity and rail pressure

Directory of Open Access Journals (Sweden)

Pietras Dariusz

2017-01-01

Full Text Available The article discusses the issue of experimentally determining the relationship between the energising time of the common rail electromagnetic injector and the set fuel quantity and rail pressure. Experimental studies according to the assumed methodology were made on a test bench enabling the dynamic flow rate measurement of the injector. The fuel system mounted on the test bench was controlled by the laboratory CI engine control unit based on the original concept of one of the authors of the article. The results of the experimental studies have made it possible to determine many of the characteristics of the fuel flow rate depending on the specified rail pressure and the energising time of the injector. An analysis was then performed followed by extrapolation of the obtained results. The data obtained from these analyses are the basis for the development of the energising time control algorithm based on a set fuel quantity and rail pressure.

Continuing Professional Development in the quantity surveying ...

African Journals Online (AJOL)

1991-01-01

Jan 1, 1991 ... The research established that quantity surveyors regarded handing in their CPD ... Surveying, Walter Sisulu University, PO Box 1421, East London, 5200, South Africa. ... Keywords: Continuing professional development, quantity surveying, perception .... In spite of this opportunity enshrined in the Act, the.

Comparison of linear measurements and analyses taken from plaster models and three-dimensional images.

Science.gov (United States)

Porto, Betina Grehs; Porto, Thiago Soares; Silva, Monica Barros; Grehs, Renésio Armindo; Pinto, Ary dos Santos; Bhandi, Shilpa H; Tonetto, Mateus Rodrigues; Bandéca, Matheus Coelho; dos Santos-Pinto, Lourdes Aparecida Martins

2014-11-01

Digital models are an alternative for carrying out analyses and devising treatment plans in orthodontics. The objective of this study was to evaluate the accuracy and the reproducibility of measurements of tooth sizes, interdental distances and analyses of occlusion using plaster models and their digital images. Thirty pairs of plaster models were chosen at random, and the digital images of each plaster model were obtained using a laser scanner (3Shape R-700, 3Shape A/S). With the plaster models, the measurements were taken using a caliper (Mitutoyo Digimatic(®), Mitutoyo (UK) Ltd) and the MicroScribe (MS) 3DX (Immersion, San Jose, Calif). For the digital images, the measurement tools used were those from the O3d software (Widialabs, Brazil). The data obtained were compared statistically using the Dahlberg formula, analysis of variance and the Tukey test (p < 0.05). The majority of the measurements, obtained using the caliper and O3d were identical, and both were significantly different from those obtained using the MS. Intra-examiner agreement was lowest when using the MS. The results demonstrated that the accuracy and reproducibility of the tooth measurements and analyses from the plaster models using the caliper and from the digital models using O3d software were identical.

Drivers militating against the pricing of sustainable construction materials: The Ghanaian quantity surveyors perspective

Directory of Open Access Journals (Sweden)

Ernest Kissi

2018-06-01

Full Text Available Sustainability has in recent times attained much acceptance as a result of its positive impact on the environment, social and economic issues. Nevertheless, in developing countries, the price of sustainable construction materials are too high. The aim of the study was to examine drivers militating against the pricing of sustainable construction materials. Through an in-depth review of literature as well as an interview survey, questionnaire was designed and administered to practicing quantity surveyors. Data generated from the survey was analysed using Principal Component Analysis which resulted four main drivers. These included: awareness challenge (AC, sustainability measurement tools challenge (SMTC, economic challenge (EC, and information challenge (IC. The study offers useful lessons on sustainable practices that pricing experts in the construction industry can draw on when pricing.The need for this study cannot be doubted since the consciousness of such challenges will help in resolving issues associated with pricing of sustainable construction materials. Keywords: Drivers, Militating, Pricing, Sustainable construction materials, Ghanaian

Improvement of job satisfaction and organisational commitment through work group identification: an examination of the quantity surveyors in Hong Kong

Directory of Open Access Journals (Sweden)

Wai Yee Betty Chiu

2013-09-01

Full Text Available Though extant literatures in other sectors indicatethat job satisfaction and organizational commitment are important fordetermining individual and organisational outcomes, limited related researchhas been conducted amongst quantity surveyors in Hong Kong. Given cooperativeworking arrangement in the quantity surveying profession, work groupidentification is regarded as an important antecedent for determining jobsatisfaction and organisational commitment. The aim of this study is to examinewhether work group identification improves job satisfaction and organisationalcommitment. A questionnaire survey is conducted to collect data from quantitysurveyors working in private sector. A total of 71 valid responses are obtainedfrom 509 contacted quantity surveyors in Hong Kong. Bivariate correlation andmultiple regression analyses are performed to find the significance ofrelationships among the variables. Data analysis results support mosthypotheses. Work group identification is found to have significant positiveeffect on job satisfaction, affective and normative commitment. The finding isa bold step for quantity surveying companies to improve their quantity surveyors’job satisfaction and commitment level. The role of other contextual and organisationalfactors on job satisfaction and organisational commitment needs to becomplemented for future research.

Continuing Professional Development in the quantity surveying ...

African Journals Online (AJOL)

This research study was conducted in order to investigate Continuing Professional Development (CPD) in the South African quantity surveying profession. The study further aimed to establish the reasons why some quantity surveyors do not acquire the required CPD hours and face losing their professional registration with ...

Among-species differences in pollen quality and quantity limitation: implications for endemics in biodiverse hotspots.

Science.gov (United States)

Alonso, Conchita; Navarro-Fernández, Carmen M; Arceo-Gómez, Gerardo; Meindl, George A; Parra-Tabla, Víctor; Ashman, Tia-Lynn

2013-11-01

Insufficient pollination is a function of quantity and quality of pollen receipt, and the relative contribution of each to pollen limitation may vary with intrinsic plant traits and extrinsic ecological properties. Community-level studies are essential to evaluate variation across species in quality limitation under common ecological conditions. This study examined whether endemic species are more limited by pollen quantity or quality than non-endemic co-flowering species in three endemic-rich plant communities located in biodiversity hotspots of different continents (Andalusia, California and Yucatan). Natural variations in pollen receipt and pollen tube formation were analysed for 20 insect-pollinated plants. Endemic and non-endemic species that co-flowered were paired in order to estimate and compare the quantity and quality components of pre-zygotic pollination success, obtained through piecewise regression analysis of the relationship between pollen grains and pollen tubes of naturally pollinated wilted flowers. Pollen tubes did not frequently exceed the number of ovules per flower. Only the combination of abundant and good quality pollen and a low number of ovules per flower conferred relief from pre-zygotic pollen limitation in the three stochastic pollination environments studied. Quality of pollen receipt was found to be as variable as quantity among study species. The relative pollination success of endemic and non-endemic species, and its quantity and quality components, was community dependent. Assessing both quality and quantity of pollen receipt is key to determining the ovule fertilization potential of both endemic and widespread plants in biodiverse hotspot regions. Large natural variation among flowers of the same species in the two components and pollen tube formation deserves further analysis in order to estimate the environmental, phenotypic and intraindividual sources of variation that may affect how plants evolve to overcome this limitation in

Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

KAUST Repository

Jing, Wei

2016-12-01

Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement was implemented by two-color pyrometry under quiescent type diesel engine conditions (1000 K and 21% O2 concentration). Different fuel quantities, which correspond to different injection widths from 0.5 ms to 2 ms under constant injection pressure (1000 bar), were used to simulate different loads in engines. For a given fuel, soot temperature and KL factor show a different trend at initial stage for different fuel quantities, where a higher soot temperature can be found in a small fuel quantity case but a higher KL factor is observed in a large fuel quantity case generally. Another difference occurs at the end of combustion due to the termination of fuel injection. Additionally, BTL flame has a lower soot temperature, especially under a larger fuel quantity (2 ms injection width). Meanwhile, average soot level is lower for BTL flame, especially under a lower fuel quantity (0.5 ms injection width). BTL shows an overall low sooting behavior with low soot temperature compared to diesel, however, trade-off between soot level and soot temperature needs to be carefully selected when different loads are used.

A thermogravimetric method for accurate determination of thermodynamic quantities at high temperatures

NARCIS (Netherlands)

Verdonk, A.H.; Nedermeijer, J.; Laverman, J.W.

1975-01-01

A method for the determination of the change in enthalpy, entropy, and specific heat capacity for monovariant heterogenous equilibria is presented. These quantities are obtained indirectly by measuring the temperature dependence of equilibrium pressures. At a given pressure of the relevant gas the

Monitoring the eye lens: which dose quantity is adequate?

International Nuclear Information System (INIS)

Behrens, R; Dietze, G

2010-01-01

Recent epidemiological studies suggest a rather low dose threshold (below 0.5 Gy) for the induction of a cataract of the eye lens. Some other studies even assume that there is no threshold at all. Therefore, protection measures have to be optimized and current dose limits for the eye lens may be reduced in the future. The question of which personal dose equivalent quantity is appropriate for monitoring the dose to the eye lens arises from this situation. While in many countries dosemeters calibrated in terms of the dose equivalent quantity H p (0.07) have been seen as being adequate for monitoring the dose to the eye lens, this might be questionable in the case of reduced dose limits and, thus, it may become necessary to use the dose equivalent quantity H p (3) for this purpose. To discuss this question, the dose conversion coefficients for the equivalent dose of the eye lens (in the following eye lens dose) were determined for realistic photon and beta radiation fields and compared with the values of the corresponding conversion coefficients for the different operational quantities. The values obtained lead to the following conclusions: in radiation fields where most of the dose comes from photons, especially x-rays, it is appropriate to use dosemeters calibrated in terms of H p (0.07) on a slab phantom, while in other radiation fields (dominated by beta radiation or unknown contributions of photon and beta radiation) dosemeters calibrated in terms of H p (3) on a slab phantom should be used. As an alternative, dosemeters calibrated in terms of H p (0.07) on a slab phantom could also be used; however, in radiation fields containing beta radiation with the end point energy near 1 MeV, an overestimation of the eye lens dose by up to a factor of 550 is possible.

Remarks and suggestions concerned with formulation of the definition of quantity ''committed dose'' and quantity ''radiation burden'' useful in estimates of population exposure

International Nuclear Information System (INIS)

Cwik, T.

1990-01-01

The paper contains remarks to the definitions of the quantity ''commited dose'' given in the publications of the ICRP. The suggestions are presented on the mode of formulating the definition of the quantity ''commited dose'' and the definition of the quantity denoted hitherto by the symbol H 50 . The other suggestions deal with introduction of the quantity ''radiation burden'', assigned for use in assessments of irradiation expressed ''per caput'' of population. 9 refs. (author)

Organizational citizenship behavior and the quantity and quality of work group performance.

Science.gov (United States)

Podsakoff, P M; Ahearne, M; MacKenzie, S B

1997-04-01

Despite the widespread interest in the topic of organizational citizenship behaviors (OCBs), little empirical research has tested the fundamental assumption that these forms of behavior improve the effectiveness of work groups or organizations in which they are exhibited. In the present study, the effects of OCBs on the quantity and quality of the performance of 218 people working in 40 machine crews in a paper mill located in the Northeastern United States were examined. The results indicate that helping behavior and sportsmanship had significant effects on performance quantity and that helping behavior had a significant impact on performance quality. However, civic virtue had no effect on either performance measure.

Measuring instruments of the Physikalisch-Technische Bundesanstalt for realization of the units of the dosimetric quantities standard ion dose, photon-equivalent dose and air-kerma

International Nuclear Information System (INIS)

Engelke, B.A.; Oetzmann, W.; Struppek, G.

1988-08-01

The realization of the units of the dosimetric quantities exposure, air-kerma and photon-equivalent dose is an important task of the Physikalisch-Technische Bundesanstalt. The report describes the measuring instruments and other technical equipment as well as the determination of the numerous corrections needed. All data and correction factors required for the realization of the units mentioned above are given in many diagrams and tables. (orig.) [de

41 CFR 101-27.102 - Economic order quantity principle.

Science.gov (United States)

2010-07-01

... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Economic order quantity...

Relevance of protection quantities in medical exposures

International Nuclear Information System (INIS)

Pradhan, A.S.

2008-01-01

International Commission on Radiological Protection (ICRP) continues to classify the exposures to radiation in three categories; namely 1- occupational exposure, 2- public exposure, and 3- medical exposure. Protection quantities are primarily meant for the regulatory purpose in radiological protection for controlling and limiting stochastic risks in occupational and public exposures. These are based on two basic assumptions of 1- linear no-threshold dose-effect relationship (LNT) at low doses and 2- long-term additivity of low doses. Medical exposure are predominantly delivered to individuals (patients) undergoing diagnostic examinations, interventional procedures and radiation therapy but also include individual caring for or comforting patients incurring exposure and the volunteers of biomedical medical research programmes. Radiation protection is as relevant to occupational and public exposure as to medical exposures except that the dose limits set for the formers are not applicable to medical exposure but reference levels and dose constrains are recommended for diagnostic and interventional medical procedures. In medical institutions, both the occupational and medical exposure takes place. Since the doses in diagnostic examinations are low, it has been observed that not only the protection quantities are often used in such cases but these are extended to estimate the number of cancer deaths due to such practices. One of the striking features of the new ICRP recommendations has been to elaborate the concepts of the dosimetric quantities. The limitation of protection quantities ((Effective dose, E=Σ RT D TR .W T .W R and Equivalent Dose H T =Σ RT D TR .W R ) have been brought out and this has raised a great concern and initiated debates on the use of these quantities in medical exposures. Consequently, ICRP has set a task group to provide more details and the recommendations. It has, therefore, became important to draw the attention of medical physics community

DOE approach to threshold quantities

International Nuclear Information System (INIS)

Wickham, L.E.; Kluk, A.F.; Department of Energy, Washington, DC)

1985-01-01

The Department of Energy (DOE) is developing the concept of threshold quantities for use in determining which waste materials must be handled as radioactive waste and which may be disposed of as nonradioactive waste at its sites. Waste above this concentration level would be managed as radioactive or mixed waste (if hazardous chemicals are present); waste below this level would be handled as sanitary waste. Ideally, the threshold must be set high enough to significantly reduce the amount of waste requiring special handling. It must also be low enough so that waste at the threshold quantity poses a very small health risk and multiple exposures to such waste would still constitute a small health risk. It should also be practical to segregate waste above or below the threshold quantity using available instrumentation. Guidance is being prepared to aid DOE sites in establishing threshold quantity values based on pathways analysis using site-specific parameters (waste stream characteristics, maximum exposed individual, population considerations, and site specific parameters such as rainfall, etc.). A guidance dose of between 0.001 to 1.0 mSv/y (0.1 to 100 mrem/y) was recommended with 0.3 mSv/y (30 mrem/y) selected as the guidance dose upon which to base calculations. Several tasks were identified, beginning with the selection of a suitable pathway model for relating dose to the concentration of radioactivity in the waste. Threshold concentrations corresponding to the guidance dose were determined for waste disposal sites at a selected humid and arid site. Finally, cost-benefit considerations at the example sites were addressed. The results of the various tasks are summarized and the relationship of this effort with related developments at other agencies discussed

Skin dose estimation due to a contamination by a radionuclide β emitter: are doses equivalent good estimator of protection quantities?

International Nuclear Information System (INIS)

Bourgois, L.

2011-01-01

When handling radioactive β emitters, measurements in terms of personal dose equivalents H p (0.07) are used to estimate the equivalent dose limit to skin or extremities given by regulations. First of all, analytical expressions for individual dose equivalents H p (0.07) and equivalent doses to the extremities H skin are given for a point source and for contamination with a radionuclide β emitter. Second of all, operational quantities and protection quantities are compared. It is shown that in this case the operational quantities significantly overstate the protection quantities. For a skin contamination the ratio between operational quantities and protection quantities is 2 for a maximum β energy of 3 MeV and 90 for a maximum β energy of 150 keV. (author)

Natural products phytotoxicity A bioassay suitable for small quantities of slightly water-soluble compounds.

Science.gov (United States)

Dornbos, D L; Spencer, G F

1990-02-01

A large variety of secondary metabolites that can inhibit germination and/or seedling growth are produced by plants in low quantities. The objective of this study was to develop a bioassay capable of reliably assessing reductions in germination percentage and seedling length of small-seeded plant species caused by exposure to minute quantities of these compounds. The germination and growth of alfalfa (Medicago saliva), annual ryegrass (Lolium multiflorum), and velvetleaf (Abutilon theophrasti) were evaluated against six known phytotoxins from five chemical classes; cinmethylin (a herbicidal cineole derivative) was selected as a comparison standard. Each phytotoxin, dissolved in a suitable organic solvent, was placed on water-agar in small tissue culture wells. After the solvent evaporated, imbibed seeds were placed on the agar; after three days, germination percentages and seedling lengths were measured. Compared to a commonly used filter paper procedure, this modified agar bioassay required smaller quantities of compound per seed for comparable bioassay results. This bioassay also readily permitted the measurement of seedling length, a more sensitive indicator of phytotoxicity than germination. Seedling length decreased sigmoidally as the toxin concentration increased logarithmically. Phytotoxicity was a function of both compound and plant species. Cinmethylin, a grass herbicide, reduced the length of annual ryegrass seedlings by 90-100%, whereas that of alfalfa and velvetleaf was inhibited slightly. The agar bioassay facilitated the rapid and reliable testing of slightly water-soluble compounds, requiring only minute quantities of each compound to give reproducible results.

Discounting of quantity surveying fees in South Africa

African Journals Online (AJOL)

by clients have forced Quantity Surveying firms into competition with ... Furthermore, 43% of consulting engineering firms were discounting their fees at a rate of .... Quantity. Surveying services are also offered in the fields of dispute resolution,.

The quantity time relation in the ionizing radiations

Science.gov (United States)

Jordão, B. O.; Quaresma, D. S.; Peixoto, J. G. P.

2018-03-01

The metrology area has taken a step forward with regard to the uncertainty calculation. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (i) the development and calibration of a microcontrolled time device with a resolution of 1x10-4 s, in order to characterize the time greatness and make it re-producible; (ii) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (iii) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate.

Measurement of fast transient pressures

International Nuclear Information System (INIS)

Procaccia, Henri

1978-01-01

The accuracy, reliability and sensitivity of a pressure transducers define its principal static characteristics. When the quantity measured varies with time, the measurement carries a dynamic error and a delay depending on the frequency of this variation. Hence, when fast pressure changes in a fluid have to be determined, different kinds of pressure transducers can be used depending on their inherent dynamic characteristics which must be compared with those of the transient phenomenon to be analysed. The text describes the pressure transducers generally employed in industry for analysing such phenomenon and gives two practical applications developed in the EDF: the first submits the measurements and results of pump cavitation tests carried out at the Vitry II EDF power station; the second deals with hammer blows particularly noticed in nuclear power stations and required the use of transducers of exceptionally high performance such as strain gauge transducers and piezoelectric transducers (response time within 1m sec.) [fr

Biologically Weighted Quantities in Radiotherapy: an EMRP Joint Research Project

Directory of Open Access Journals (Sweden)

Rabus Hans

2014-01-01

Full Text Available Funded within the European Metrology Research Programme (EMRP [1], the joint research project “Biologically weighted quantities in radiotherapy” (BioQuaRT [2] aims to develop measurement and simulation techniques for determining the physical properties of ionising particle tracks on different length scales (about 2 nm to 10 μm, and to investigate the correlation of these track structure characteristics with the biological effects of radiation at the cellular level. Work package 1 develops micro-calorimeter prototypes for the direct measurement of lineal energy and will characterise their response for different ion beams by experiment and modelling. Work package 2 develops techniques to measure particle track structure on different length scales in the nanometre range as well as a measurement device integrating a silicon microdosimeter and a nanodosimeter. Work package 3 investigates the indirect effects of radiation based on probes for quantifying particular radical and reactive oxygen species (ROS. Work package 4 focuses on the biological aspects of radiation damage and will produce data on initial DNA damage and late effects for radiotherapy beams of different qualities. Work package 5 provides evaluated data sets of DNA cross-sections and develops a multi-scale model to address microscopic and nanometric track structure properties. The project consortium includes three linked researchers holding so-called Researcher Excellence Grants, who carry out ancillary investigations such as developing and benchmarking a new biophysical model for induction of early radiation damage and developing methods for the translation of quantities derived from particle track structure to clinical applications in ion beam therapy.

A conserved quantity in thin body dynamics

International Nuclear Information System (INIS)

Hanna, J.A.; Pendar, H.

2016-01-01

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

A conserved quantity in thin body dynamics

Energy Technology Data Exchange (ETDEWEB)

Hanna, J.A., E-mail: hannaj@vt.edu [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Department of Physics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Pendar, H. [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States)

2016-02-15

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

The ICRU dose equivalence quantities in radiation protection

International Nuclear Information System (INIS)

Grimbergen, T.W.M.

1990-09-01

The definitions and application of the new ICRU radiation protection quantities have been reviewed and studied in literature. Special emphasis was laid on the consequences of the use of the new quantities by personnel dosimetry services, and on the consequences of the use of the new quantities during an intercomparison programme for dosimetry services. The study shows that the recommendations of the ICRU are not yet complete and not fully realizable. This means that the dosimetry services always have to make certain approximations, when they use the new quantities. In literature, several approaches have been proposed. The feasibility of an approach depends on the characteristics of the dosimeters used. The use of different approaches by the dosimetry services is thought to be of possible influence on the results of an intercomparison programme. (author). 42 refs.; 3 figs.; 1 tab

Foreign materials in the repository - update of estimated quantities

International Nuclear Information System (INIS)

Hagros, A.

2007-03-01

In a repository for spent nuclear fuel, a variety of materials are used during the construction process and during the operation of the repository. In addition to materials necessary for the construction and operation, some materials may be transported into the repository through the ventilation air, as emissions from vehicles, as waste produced by the staff etc. Both of these two types of materials are considered here and their quantities - both the introduced quantities and the quantities that remain after closure - in the repository constructed at Olkiluoto in Eurajoki, Finland are estimated here based on new information. This work is intended to update the estimations that have been made previously, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility ONKALO at Olkiluoto. During this construction process, the quantities of the different construction materials introduced into the underground openings have been monitored and they form a basis for estimating the quantities to be used in the future. The estimations made in this report are specific to a KBS-3V type repository and to the Olkiluoto site, although in some cases more generic information has been used, particularly when the relevant quantities have not been monitored in the ONKALO. The estimations are based on the new repository layout produced in 2006 and consider the latest plans for grouting and rock support. As these plans are generally not final yet, several different alternative plans are assumed when necessary. Also two different strategies for the backfilling of the tunnels are considered. The most significant differences with respect to the results of an earlier estimation are related to the materials used in grouting, shotcreting and in support bolts. In the cases where a mixture of bentonite and crushed rock is the used backfill alternative, gypsum and cement are the materials with the largest quantities remaining in the

Quantities of natural gas transmitted in January-December 2012. Quantities of natural gas transported in January-December 2012

International Nuclear Information System (INIS)

2013-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2012: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

The quality and quantity of runoff and groundwater in two overburden dumps undergoing pyritic oxidation

International Nuclear Information System (INIS)

Daniel, J.A.; Harries, J.R.; Ritchie, A.I.M.

1983-01-01

The quality and quantity of runoff and seepage water from two waste rock dumps at the abandoned uranium mine at Rum Jungle, N.T., have been monitored over various time intervals since 1975. Both dumps contain pyrite which is oxidising and solubilising trace metals within the dumps. Results are presented for the quality and quantity of runoff from both dumps measured in the 1980-81 wet season. The rainfall/runoff characteristics of the two dumps measured during this wet season are similar and in good agreement with measurements made in previous wet seasons. Pollution loads in runoff were only a few per cent of pollution loads in water percolating through to the base of the dumps. The rainfall/runoff characteristics and the dominance of pollution loads in water percolating through the dumps are likely to apply to other similar waste rock dumps

Assessment of Sleep Quantity and Sleep Disturbances During Recovery From Sports-Related Concussion in Youth Athletes.

Science.gov (United States)

Murdaugh, Donna L; Ono, Kim E; Reisner, Andrew; Burns, Thomas G

2018-05-01

To determine the relation between sleep quantity and sleep disturbances on symptoms and neurocognitive ability during the acute phase (sports-related concussion (SRC; >21d). Prospective inception cohort study. General community setting of regional middle and high schools. A sample (N=971) including youth athletes with SRC (n=528) and controls (n=443) (age, 10-18y). Not applicable. Athletes completed the Immediate Post-Concussion Assessment and Cognitive Testing battery. Partial correlation analyses and independent t tests were conducted to assess sleep quantity the night before testing. Multivariate analysis of covariance was used to assess sleep disturbances and their interaction with age. Less sleep quantity was correlated with greater report of cognitive (P=.001) and neuropsychological (P=.024) symptoms specific to prolonged recovery from SRC. Sleep disturbances significantly affect each migraine, cognitive, and neuropsychological symptoms (Psleep disturbances and age (P=.04) at >21 days post-SRC. Findings emphasize that the continued presence of low sleep quantity and sleep disturbances in youth athletes with SRC should be a specific indicator to health professionals that these athletes are at an increased risk of protracted recovery. Further research should identify additional factors that may interact with sleep to increase the risk of protracted recovery. Copyright © 2018 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Formatting data files for repeated-measures analyses in SPSS: Using the Aggregate and Restructure procedures

Directory of Open Access Journals (Sweden)

Gyslain Giguère

2006-03-01

Full Text Available In this tutorial, we demonstrate how to use the Aggregate and Restructure procedures available in SPSS (versions 11 and up to prepare data files for repeated-measures analyses. In the first two sections of the tutorial, we briefly describe the Aggregate and Restructure procedures. In the final section, we present an example in which the data from a fictional lexical decision task are prepared for analysis using a mixed-design ANOVA. The tutorial demonstrates that the presented method is the most efficient way to prepare data for repeated-measures analyses in SPSS.

Quantity discrimination in wolves (Canis lupus

Directory of Open Access Journals (Sweden)

Ewelina eUtrata

2012-11-01

Full Text Available Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested eleven hand-raised wolves (Canis lupus in a two-way choice task. We placed a number of food items (one to four sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris and coyotes (Canis latrans, our wolves’ performance did not improve with decreasing ratio, referred to as Weber’s law. However, further studies using larger quantities than we used in the current setup are still needed to determine whether and when wolves’ quantity discrimination conforms to Weber’s law.

The quantity time relation in the ionizing radiations

Energy Technology Data Exchange (ETDEWEB)

Jordão, Bruno; Quaresma, Daniel, E-mail: bjordan@on.br [Observatorio Nacional (LPTF/ON), Rio de Janeiro, RJ (Brazil). Laboratório Primário de Tempo e Frequência; Peixoto, José Guilherme P. [Instituto de Radioproteção e Dosimetria (LNMRI/IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Laboratório Nacional de Metrologia das Radiações Ionizantes

2017-07-01

The area of metrology has taken a step forward with regard to the calculation of uncertainty. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (1) the development and calibration of a microcontrolled time device with a resolution of 1 x 10{sup -4} s, in order to characterize the time greatness and make it reproducible; (2) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (3) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate. (author)

The quantity time relation in the ionizing radiations

International Nuclear Information System (INIS)

Jordão, Bruno; Quaresma, Daniel; Peixoto, José Guilherme P.

2017-01-01

The area of metrology has taken a step forward with regard to the calculation of uncertainty. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (1) the development and calibration of a microcontrolled time device with a resolution of 1 x 10 -4 s, in order to characterize the time greatness and make it reproducible; (2) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (3) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate. (author)

Layer-Mean Quantities, Local Conservation Laws, and Vorticity

International Nuclear Information System (INIS)

Camassa, R.; Levermore, C.D.

1997-01-01

We derive local conservation laws for layer-mean quantities in two general settings. When applied to Euler flows, the first of these settings yields well-known local conservation laws for quantities averaged between material surfaces. The second, however, leads to new local conservation laws for quantities involving the vorticity that are averaged between arbitrary surfaces. These produce the crucial vorticity conservation laws in shallow water models that admit nonhydrostatic and noncolumnar motion. Moreover, they seem to lie outside the Hamiltonian paradigm of fluid dynamics. The formalism generalizes to skew-symmetric matrix fields; applications to electromagnetism are suggested. copyright 1997 The American Physical Society

Average Transverse Momentum Quantities Approaching the Lightfront

OpenAIRE

Boer, Daniel

2015-01-01

In this contribution to Light Cone 2014, three average transverse momentum quantities are discussed: the Sivers shift, the dijet imbalance, and the $p_T$ broadening. The definitions of these quantities involve integrals over all transverse momenta that are overly sensitive to the region of large transverse momenta, which conveys little information about the transverse momentum distributions of quarks and gluons inside hadrons. TMD factorization naturally suggests alternative definitions of su...

A conceptual framework for analysing and measuring land-use intensity

DEFF Research Database (Denmark)

Erb, Karl-Heinz; Haberl, Helmut; Jepsen, Martin Rudbeck

2013-01-01

Large knowledge gaps currently exist that limit our ability to understand and characterise dynamics and patterns of land-use intensity: in particular, a comprehensive conceptual framework and a system of measurement are lacking. This situation hampers the development of a sound understanding...... of the mechanisms, determinants, and constraints underlying changes in land-use intensity. On the basis of a review of approaches for studying land-use intensity, we propose a conceptual framework to quantify and analyse land-use intensity. This framework integrates three dimensions: (a) input intensity, (b) output...

Access to What? Creating a Composite Measure of Educational Quantity and Educational Quality for 11 African Countries

Science.gov (United States)

Spaull, Nicholas; Taylor, Stephen

2015-01-01

The aim of the current study is to create a composite statistic of educational quantity and educational quality by combining household data (Demographic and Health Survey) on grade completion and survey data (Southern and Eastern African Consortium for Monitoring Educational Quality) on cognitive outcomes for 11 African countries: Kenya, Lesotho,…

Forage quantity and quality

Science.gov (United States)

Jorgenson, Janet C.; Udevitz, Mark S.; Felix, Nancy A.; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

2002-01-01

The Porcupine caribou herd has traditionally used the coastal plain of the Arctic National Wildlife Refuge, Alaska, for calving. Availability of nutritious forage has been hypothesized as one of the reasons the Porcupine caribou herd migrates hundreds of kilometers to reach the coastal plain for calving (Kuropat and Bryant 1980, Russell et al. 1993).Forage quantity and quality and the chronology of snowmelt (which determines availability and phenological stages of forage) have been suggested as important habitat attributes that lead calving caribou to select one area over another (Lent 1980, White and Trudell 1980, Eastland et al. 1989). A major question when considering the impact of petroleum development is whether potential displacement of the caribou from the 1002 Area to alternate calving habitat will limit access to high quantity and quality forage.Our study had the following objectives: 1) quantify snowmelt patterns by area; 2) quantify relationships among phenology, biomass, and nutrient content of principal forage species by vegetation type; and 3) determine if traditional concentrated calving areas differ from adjacent areas with lower calving densities in terms of vegetation characteristics.

Measured sections and analyses of uranium host rocks of the Dockum Group, New Mexico and Texas

International Nuclear Information System (INIS)

Dickson, R.E.; Drake, D.P.; Reese, T.J.

1977-02-01

This report presents 27 measured sections from the Dockum Group of Late Triassic age, in the southern High Plains of eastern New Mexico and northwestern Texas. Many of the measured sections are only partial; the intent in those cases was to measure the parts of sections that had prominent sandstone/conglomerate beds or that had uranium deposits. No attempt was made to relate rock color to a rock color chart; rock colors are therefore approximate. Modal analyses (by thin-section examination) of sandstone and conglomerate samples and gamma-ray spectrometric analyses of the samples are presented in appendices

A conserved quantity in thin body dynamics

Science.gov (United States)

Hanna, J. A.; Pendar, H.

2016-02-01

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant.

Relationships of chemical composition, quantity of milt to fertility and ...

African Journals Online (AJOL)

African Journal of Food, Agriculture, Nutrition and Development ... determining the right quantity of milt that can be used to fertilize certain quantity of eggs. ... quantity of milt used for artificial reproduction in fish significantly affect water quality used ... is the major organic substance that supplies the spermatozoa with energy.

Six categories of ionizing radiation quantities practical in various fields

International Nuclear Information System (INIS)

Zheng Junzheng; Zhuo Weihai

2011-01-01

This paper is the part of review on the evolvement of the systems for ionizing radiation quantities and units. In the paper, for better understanding and correct use of the relevant quantities of ionizing radiation, the major ionizing radiation quantities in various fields are divided into six categories. (authors)

Lie-Mei symmetry and conserved quantities of the Rosenberg problem

International Nuclear Information System (INIS)

Liu Xiao-Wei; Li Yuan-Cheng

2011-01-01

The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry. (general)

Lie-Mei symmetry and conserved quantities of the Rosenberg problem

Science.gov (United States)

Liu, Xiao-Wei; Li, Yuan-Cheng

2011-07-01

The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry.

Optimal trading quantity integration as a basis for optimal portfolio management

Directory of Open Access Journals (Sweden)

Saša Žiković

2005-06-01

Full Text Available The author in this paper points out the reason behind calculating and using optimal trading quantity in conjunction with Markowitz’s Modern portfolio theory. In the opening part the author presents an example of calculating optimal weights using Markowitz’s Mean-Variance approach, followed by an explanation of basic logic behind optimal trading quantity. The use of optimal trading quantity is not limited to systems with Bernoulli outcome, but can also be used when trading shares, futures, options etc. Optimal trading quantity points out two often-overlooked axioms: (1 a system with negative mathematical expectancy can never be transformed in a system with positive mathematical expectancy, (2 by missing the optimal trading quantity an investor can turn a system with positive expectancy into a negative one. Optimal trading quantity is that quantity which maximizes geometric mean (growth function of a particular system. To determine the optimal trading quantity for simpler systems, with a very limited number of outcomes, a set of Kelly’s formulas is appropriate. In the conclusion the summary of the paper is presented.

21 CFR 1314.20 - Restrictions on sales quantity.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Restrictions on sales quantity. 1314.20 Section 1314.20 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE RETAIL SALE OF SCHEDULED LISTED CHEMICAL PRODUCTS Sales by Regulated Sellers § 1314.20 Restrictions on sales quantity. (a) Without...

Quantity-split strategy under two-contractor competitive procurement environment

OpenAIRE

Boger, Dan C.; Liao, Shu S.

1988-01-01

This report discusses the various market scenarios that provide bid price manipulation opportunities under the dual source competition environment. Two different quantity-split strategies were developed one for the case when one of the suppliers does not have the capacity to produce the majority of the annual quantity requirement and the other for the case when neither contractor is interested in using low prices to capture the larger share of annual quantity. Keywords: Dual sourcing, Quantit...

ANALYZER OF QUANTITY AND QUALITY OF THE ELECTRIC POWER

Directory of Open Access Journals (Sweden)

A. I. Semilyak

2013-01-01

Full Text Available One of the activities of the research center for “Energy Saving Technologies and Smart Metering in Electrical Power Engineering" is research work on the use of electronic devices and systems of intelligent power distribution, produced by Analog Devices and equipped with the accurate energy consumption measurement feature. The article focuses on the development of the analyzer of quantity and quality of electric energy.The main part of the analyzer is a metering IC by Analog Devices ADE7878, designed for use in commercial and industrial smart electricity meters. Such counters measure the amount of consumed or produced electric energy with high accuracy and have the means of remote meter reading.

Measuring social capital through multivariate analyses for the IQ-SC.

Science.gov (United States)

Campos, Ana Cristina Viana; Borges, Carolina Marques; Vargas, Andréa Maria Duarte; Gomes, Viviane Elisangela; Lucas, Simone Dutra; Ferreira e Ferreira, Efigênia

2015-01-20

Social capital can be viewed as a societal process that works toward the common good as well as toward the good of the collective based on trust, reciprocity, and solidarity. Our study aimed to present two multivariate statistical analyses to examine the formation of latent classes of social capital using the IQ-SC and to identify the most important factors in building an indicator of individual social capital. A cross-sectional study was conducted in 2009 among working adolescents supported by a Brazilian NGO. The sample consisted of 363 individuals, and data were collected using the World Bank Questionnaire for measuring social capital. First, the participants were grouped by a segmentation analysis using the Two Step Cluster method based on the Euclidian distance and the centroid criteria as the criteria for aggregate answers. Using specific weights for each item, discriminant analysis was used to validate the cluster analysis in an attempt to maximize the variance among the groups with respect to the variance within the clusters. "Community participation" and "trust in one's neighbors" contributed significantly to the development of the model with two distinct discriminant functions (p < 0.001). The majority of cases (95.0%) and non-cases (93.1%) were correctly classified by discriminant analysis. The two multivariate analyses (segmentation analysis and canonical discriminant analysis), used together, can be considered good choices for measuring social capital. Our results indicate that it is possible to form three social capital groups (low, medium and high) using the IQ-SC.

Editorial: New operational dose equivalent quantities

International Nuclear Information System (INIS)

Harvey, J.R.

1985-01-01

The ICRU Report 39 entitled ''Determination of Dose Equivalents Resulting from External Radiation Sources'' is briefly discussed. Four new operational dose equivalent quantities have been recommended in ICRU 39. The 'ambient dose equivalent' and the 'directional dose equivalent' are applicable to environmental monitoring and the 'individual dose equivalent, penetrating' and the 'individual dose equivalent, superficial' are applicable to individual monitoring. The quantities should meet the needs of day-to-day operational practice, while being acceptable to those concerned with metrological precision, and at the same time be used to give effective control consistent with current perceptions of the risks associated with exposure to ionizing radiations. (U.K.)

Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

KAUST Repository

Jing, Wei; Wu, Zengyang; Roberts, William L.; Fang, Tiegang

2016-01-01

Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement

A new support measure to quantify the impact of local optima in phylogenetic analyses.

KAUST Repository

Brammer, Grant

2011-09-29

Phylogentic analyses are often incorrectly assumed to have stabilized to a single optimum. However, a set of trees from a phylogenetic analysis may contain multiple distinct local optima with each optimum providing different levels of support for each clade. For situations with multiple local optima, we propose p-support which is a clade support measure that shows the impact optima have on a final consensus tree. Our p-support measure is implemented in our PeakMapper software package. We study our approach on two published, large-scale biological tree collections. PeakMapper shows that each data set contains multiple local optima. p-support shows that both datasets contain clades in the majority consensus tree that are only supported by a subset of the local optima. Clades with low p-support are most likely to benefit from further investigation. These tools provide researchers with new information regarding phylogenetic analyses beyond what is provided by other support measures alone.

48 CFR 245.7309-8 - Variations in quantity or weight.

Science.gov (United States)

2010-10-01

... Inventory 245.7309-8 Variations in quantity or weight. When property is sold on a “unit price” basis, the Contractor reserves the right to vary by up to 15 percent the quantity or weight listed in the Invitation and... price shall be adjusted in accordance with the unit price and on the basis of the quantity or weight...

Management of small quantities of radioactive waste

International Nuclear Information System (INIS)

1998-09-01

The main objective of this publication is to provide practical guidance primarily to developing Member States on the predisposal management of small quantities of radioactive waste arising from hospitals, laboratories, industries, institutions, research reactors and research centres.The publication covers the management of liquid, solid and gaseous radioactive wastes at the users' premises and gives general guidance on procedures at a centralized waste management facility. Predisposal management of radioactive waste includes handling, treatment, conditioning, storage and transportation. This publication provides information and guidance on the following topics: national waste management framework; origin and characteristics of radioactive waste arising from users generating small quantities of waste; radioactive waste management concepts appropriate for small quantities; local waste management; the documentation and approval necessary for the consignment of waste to a centralized waste management facility; centralized waste management; exemption of radionuclides from the regulatory body; transportation; environmental monitoring; quality assurance for the whole predisposal process; regional co-operation aspects

Morphometric analysis - Cone beam computed tomography to predict bone quality and quantity.

Science.gov (United States)

Hohlweg-Majert, B; Metzger, M C; Kummer, T; Schulze, D

2011-07-01

Modified quantitative computed tomography is a method used to predict bone quality and quantify the bone mass of the jaw. The aim of this study was to determine whether bone quantity or quality was detected by cone beam computed tomography (CBCT) combined with image analysis. MATERIALS AND PROCEDURES: Different measurements recorded on two phantoms (Siemens phantom, Comac phantom) were evaluated on images taken with the Somatom VolumeZoom (Siemens Medical Solutions, Erlangen, Germany) and the NewTom 9000 (NIM s.r.l., Verona, Italy) in order to calculate a calibration curve. The spatial relationships of six sample cylinders and the repositioning from four pig skull halves relative to adjacent defined anatomical structures were assessed by means of three-dimensional visualization software. The calibration curves for computer tomography (CT) and cone beam computer tomography (CBCT) using the Siemens phantom showed linear correlation in both modalities between the Hounsfield Units (HU) and bone morphology. A correction factor for CBCT was calculated. Exact information about the micromorphology of the bone cylinders was only available using of micro computer tomography. Cone-beam computer tomography is a suitable choice for analysing bone mass, but, it does not give any information about bone quality. 2010 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Determination of dosimetric quantities in pediatric abdominal computed tomography scans

Energy Technology Data Exchange (ETDEWEB)

Jornada, Tiago da Silva [Universidade Federal de Sao Paulo (UNIFESP), Sao Paulo, SP (Brazil). Escola Paulista de Medicina. Dept. de Diagnostipo por Imagem; Silva, Teogenes Augusto da, E-mail: silvata@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2014-09-15

Objective: aiming at contributing to the knowledge on doses in computed tomography (CT), this study has the objective of determining dosimetric quantities associated with pediatric abdominal CT scans, comparing the data with diagnostic reference levels (DRL). Materials and methods: the study was developed with a Toshiba Asteion single-slice CT scanner and a GE BrightSpeed multi-slice CT unit in two hospitals. Measurements were performed with a pencil-type ionization chamber and a 16 cm-diameter polymethylmethacrylate trunk phantom. Results: No significant difference was observed in the values for weighted air kerma index (C{sub W}), but the differences were relevant in values for volumetric air kerma index (C{sub VOL}), air kerma-length product (P{sub KL,CT}) and effective dose. Conclusion: Only the CW values were lower than the DRL, suggesting that dose optimization might not be necessary. However, P{sub KL,CT} and effective dose values stressed that there still is room for reducing pediatric radiation doses. The present study emphasizes the importance of determining all dosimetric quantities associated with CT scans. (author)

Determination of dosimetric quantities in pediatric abdominal computed tomography scans*

Science.gov (United States)

Jornada, Tiago da Silva; da Silva, Teógenes Augusto

2014-01-01

Objective Aiming at contributing to the knowledge on doses in computed tomography (CT), this study has the objective of determining dosimetric quantities associated with pediatric abdominal CT scans, comparing the data with diagnostic reference levels (DRL). Materials and methods The study was developed with a Toshiba Asteion single-slice CT scanner and a GE BrightSpeed multi-slice CT unit in two hospitals. Measurements were performed with a pencil-type ionization chamber and a 16 cm-diameter polymethylmethacrylate trunk phantom. Results No significant difference was observed in the values for weighted air kerma index (CW), but the differences were relevant in values for volumetric air kerma index (CVOL), air kerma-length product (PKL,CT) and effective dose. Conclusion Only the CW values were lower than the DRL, suggesting that dose optimization might not be necessary. However, PKL,CT and effective dose values stressed that there still is room for reducing pediatric radiation doses. The present study emphasizes the importance of determining all dosimetric quantities associated with CT scans. PMID:25741103

Dosimetric radiation protection quantities. Impact of the forthcoming ICRP recommendations

International Nuclear Information System (INIS)

Pradhan, A.S.; Lee, J.I.; Kim, J.L.; Kim, B.H.

2008-01-01

The physical quantities namely fluence, kerma and absorbed dose provide the base for the operational and the protection quantities. The absorbed dose continues to be the fundamental physical quantity for the radiological protection. The most striking feature relating the quantities in the forthcoming recommendations is the updating of the radiation and tissue weighting factors based on the latest available scientific information on radiobiology and the physics of radiation exposure. This is bound to make a significant impact in arriving at the equivalent doses and effective dose. For external exposures of neutrons, the forthcoming recommendations are going to improve the relationship between the operational and protection quantities. The changes in the tissue weighting factors of some tissues/organs, the inclusion of several new tissues/organs for the consideration of tissue weighting factors and the use of the proposed Reference Male and Reference Female voxel phantoms would require new conversion coefficients and dose coefficients for external and internal exposures. The other striking feature appears to be the details of the concepts to ensure that the protections quantities are used for the appropriate and intended purposes only and the misuse is avoided. (author)

Valuation of Construction Projects Based on of Quantity Scale by using Expert System

Directory of Open Access Journals (Sweden)

Entisar Kadhim Rasheed

2016-02-01

Full Text Available The subject of an valuation of quality of construction projects is one of the topics which it becomes necessary of the absence of the quantity standards in measuring the control works and the quality valuation standards in constructional projects. In the time being it depends on the experience of the workers which leads to an apparent differences in the valuation. The idea of this research came to put the standards to evaluate the quality of the projects in a special system depending on quantity scale nor quality specifying in order to prepare an expert system “ Crystal “ to apply this special system to able the engineers to valuate the quality of their projects easily and in more accurate ways.

Variation of organic matter quantity and quality in streams at Critical Zone Observatory watersheds

Science.gov (United States)

Miller, Matthew P.; Boyer, Elizabeth W.; McKnight, Diane M.; Brown, Michael G.; Gabor, Rachel S.; Hunsaker, Carolyn T.; Iavorivska , Lidiia; Inamdar, Shreeram; Kaplan, Louis A.; Johnson, Dale W.; Lin, Henry; McDowell, William H.; Perdrial, Julia N.

2016-01-01

The quantity and chemical composition of dissolved organic matter (DOM) in surface waters influence ecosystem processes and anthropogenic use of freshwater. However, despite the importance of understanding spatial and temporal patterns in DOM, measures of DOM quality are not routinely included as part of large-scale ecosystem monitoring programs and variations in analytical procedures can introduce artifacts. In this study, we used consistent sampling and analytical methods to meet the objective of defining variability in DOM quantity and quality and other measures of water quality in streamflow issuing from small forested watersheds located within five Critical Zone Observatory sites representing contrasting environmental conditions. Results show distinct separations among sites as a function of water quality constituents. Relationships among rates of atmospheric deposition, water quality conditions, and stream DOM quantity and quality are consistent with the notion that areas with relatively high rates of atmospheric nitrogen and sulfur deposition and high concentrations of divalent cations result in selective transport of DOM derived from microbial sources, including in-stream microbial phototrophs. We suggest that the critical zone as a whole strongly influences the origin, composition, and fate of DOM in streams. This study highlights the value of consistent DOM characterization methods included as part of long-term monitoring programs for improving our understanding of interactions among ecosystem processes as controls on DOM biogeochemistry.

Non-destructive measurements of uranium and thorium concentrations and quantities

International Nuclear Information System (INIS)

Dragnev, T.N.; Damjanov, B.P.; Karamanova, J.S.

1979-01-01

The passive X-ray fluorescent-gamma spectrometry method and technique for uranium concentration measurements was developed and tested. It is based on the measurement of the intensity ratios of self-excited Ksub(α) X-rays of uranium to the intensity of the combined peak with 92.8 keV average energy. The last peak has 92.367 and 92.792 keV gamma rays of 234 Th, representing the activities of 238 U and its daughter isotopes, and 93.35 keV Th Ksub(α) X-rays representing the activities of 235 U and its daughters. The results of the measurements do not depend on the size and the shape of the measurements. The procedure is developed to take automatically into account the presence of any absorber or cladding between the measured sample and the detector. The attainable precision of the measurements (at 95% confidence level) is 0.2 - 0.3%. If combined with enrichment measurements, and after suitable empirical calibration, the method can be used without standards. Gamma-spectrometric measurements of 238 U and 232 Th are based on the daughter isotopes' gamma activities. However, this is correct only when there is a corresponding equilibrium between 238 U and 232 Th and the daughter isotopes' activities. Where such equilibrium is not reached the status of the daughter products' activities regarding equilibrium, has to be taken into account. Two methods of quantitative corrections are proposed: (i) The use of an absolute determination of the 228 Ac/ 224 Ra activity ratio through self-calibrated measurements and individual activities and their correlation with the equilibrium activities. (ii) Use of two of the same sample measurements at two different moments during the unrestored equilibrium and the correlation of the measurement results with the 232 Th activity. This method can be generally applied. (author)

Analyses of cavitation instabilities in ductile metals

DEFF Research Database (Denmark)

Tvergaard, Viggo

2007-01-01

Cavitation instabilities have been predicted for a single void in a ductile metal stressed under high triaxiality conditions. In experiments for a ceramic reinforced by metal particles a single dominant void has been observed on the fracture surface of some of the metal particles bridging a crack......, and also tests for a thin ductile metal layer bonding two ceramic blocks have indicated rapid void growth. Analyses for these material configurations are discussed here. When the void radius is very small, a nonlocal plasticity model is needed to account for observed size-effects, and recent analyses......, while the surrounding voids are represented by a porous ductile material model in terms of a field quantity that specifies the variation of the void volume fraction in the surrounding metal....

On pure-strategy Nash equilibria in price-quantity games

NARCIS (Netherlands)

Bos, I.; Vermeulen, A.J.

2015-01-01

This paper examines the existence and characteristics of pure-strategy Nash equilibria in oligopoly models in which firms set both prices and quantities. Existence is proved for a broad and natural class of price-quantity games. With differentiated products, the equilibrium outcome is similar to

FY 2016 Status Report: CIRFT Testing Data Analyses and Updated Curvature Measurements

Energy Technology Data Exchange (ETDEWEB)

Wang, Jy-An John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wang, Hong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-08-01

This report provides a detailed description of FY15 test result corrections/analysis based on the FY16 Cyclic Integrated Reversible-Bending Fatigue Tester (CIRFT) test program methodology update used to evaluate the vibration integrity of spent nuclear fuel (SNF) under normal transportation conditions. The CIRFT consists of a U-frame testing setup and a real-time curvature measurement method. The three-component U-frame setup of the CIRFT has two rigid arms and linkages to a universal testing machine. The curvature of rod bending is obtained through a three-point deflection measurement method. Three linear variable differential transformers (LVDTs) are used and clamped to the side connecting plates of the U-frame to capture the deformation of the rod. The contact-based measurement, or three-LVDT-based curvature measurement system, on SNF rods has been proven to be quite reliable in CIRFT testing. However, how the LVDT head contacts the SNF rod may have a significant effect on the curvature measurement, depending on the magnitude and direction of rod curvature. It has been demonstrated that the contact/curvature issues can be corrected by using a correction on the sensor spacing. The sensor spacing defines the separation of the three LVDT probes and is a critical quantity in calculating the rod curvature once the deflections are obtained. The sensor spacing correction can be determined by using chisel-type probes. The method has been critically examined this year and has been shown to be difficult to implement in a hot cell environment, and thus cannot be implemented effectively. A correction based on the proposed equivalent gauge-length has the required flexibility and accuracy and can be appropriately used as a correction factor. The correction method based on the equivalent gauge length has been successfully demonstrated in CIRFT data analysis for the dynamic tests conducted on Limerick (LMK) (17 tests), North Anna (NA) (6 tests), and Catawba mixed oxide (MOX

Definitions of Quantities and Units.

Science.gov (United States)

Spurgin, C. B.

1983-01-01

Compares various methods of defining derived quantities, arguing for a definitional formula using base or fundamental units in a word equation, or symbol-equations with the symbols explained. Suggests that fundamental units be defined operationally or left regarded as intuitive as in the case of length and time. (JM)

USE OF BOUNDING ANALYSES TO ESTIMATE THE PREFORMANCE OF A SEISMICALLY ISOLATED STRUCTURE

Directory of Open Access Journals (Sweden)

Gökhan ÖZDEMİR

2017-03-01

Full Text Available Current design approach for seismic isolated structures is to perform bounding analyses. These analyses provide an envelope for the response of the seismic isolated structure rather than focusing on the actual performance. In this study, the success of bounding analyses to estimate performance of a seismic isolated structure, in which the isolation is provided by means of lead rubber bearings (LRBs, is evaluated in a comparative manner. For this purpose, nonlinear response history analyses were performed under the effect of bidirectional ground motion excitations. In bounding analyses, non-deteriorating hysteretic representations were used to model the hysteretic behavior of LRBs. On the other hand, to estimate the actual performance of both the superstructure and isolator units, deteriorating hysteretic idealizations were employed. The deterioration in strength of LRBs was defined as a function of temperature rise in the lead core. The analyzed structure is an existing seismically isolated hospital building and analytically modeled in accordance with its reported design properties for both isolation units and superstructure. Results obtained from analyses where LRBs are idealized by both deteriorating and non-deteriorating hysteretic representations are used in the comparisons. The response quantities used in the comparisons are maximum isolator displacement, maximum isolator force, maximum absolute floor acceleration, and maximum relative story displacements. In an average sense, bounding analyses is found to provide conservative estimates for the selected response quantities and fulfills its intended purpose. However, it is revealed that there may be individual cases where bounding analyses fails to provide a safe envelope.

Computerized tomography in Community of Madrid. Reference dosimetric measurements

International Nuclear Information System (INIS)

Ruiz Sanz, S.; Calzado, A.; Melchor, M.; Marco, M.

1994-01-01

A total of about 43 computed tomography scanners were operating in the Autonomous Community of Madrid during 1991. A sample of 14 facilities was selected to perform dosimetric measurements in order to obtain characteristic dose profiles. From these, some quantities as the computed tomography dose index and the enhancement factor were calculated and analysed for the most common technique settings. Relations were established between the dosimetric results and technical characteristics of the scanners. (Author)

Detection Dynamics Of Nitrogen Based Explosive Quantities In Selected Cylindrical Containers

Directory of Open Access Journals (Sweden)

Ngusha Tavershima Almighty

2017-12-01

Full Text Available An experimental set up for examining the variation of detection intensity with explosive quantity has been studied. Containers made from ceramic carbon steel wood and HDPE were filled with explosive masses ranging from 10 kg to 500 kg and irradiated by a 14.1 MeV point isotropic neutron source. The resulting gamma photons were analyzed for their C N and O composition and the sum computed to yield a quantity known as the material quotient MQ. Examination of MQ values indicates an initial increase in detection intensity with increasing explosive quantity. Saturation is however reached at an explosive quantity of about 25kg where detection intensity reduces with further increase in explosive quantity. Effects of variation in explosive quantity appeared to be more pronounced for explosives contained in HDPE and wooden containers and least pronounced for those in steel containers. Source-detector configuration was identified as a major factor affecting effective detection of large masses of explosives.

Workplace stress experienced by quantity surveyors

African Journals Online (AJOL)

Paul (P.A.) Bowen, Department of Construction Economics and Management,. University of Cape Town, Private ..... Explore workplace stress levels among quantity surveyors in the developing nation of ...... London: Free. Association Books.

Mevatron-74 10MeV photon beam: a study of dosimetric quantities

International Nuclear Information System (INIS)

Souza, C.N. de

1986-01-01

The Mevatron-74 linear accelerator dosimetric quantities were studied. In water and polystyrene measurements with an ionization chamber were done for following physical parameters: maximum dose depth and surface dose, field size dependence, central axis percentage depth dose, beam flatness and simmetry, and also verification the inverse square law for the distances normally used in therapy. Isodose curves were generated by the decrement lines method. (Author) [pt

Uncertainty evaluation of thickness and warp of a silicon wafer measured by a spectrally resolved interferometer

Science.gov (United States)

Praba Drijarkara, Agustinus; Gergiso Gebrie, Tadesse; Lee, Jae Yong; Kang, Chu-Shik

2018-06-01

Evaluation of uncertainty of thickness and gravity-compensated warp of a silicon wafer measured by a spectrally resolved interferometer is presented. The evaluation is performed in a rigorous manner, by analysing the propagation of uncertainty from the input quantities through all the steps of measurement functions, in accordance with the ISO Guide to the Expression of Uncertainty in Measurement. In the evaluation, correlation between input quantities as well as uncertainty attributed to thermal effect, which were not included in earlier publications, are taken into account. The temperature dependence of the group refractive index of silicon was found to be nonlinear and varies widely within a wafer and also between different wafers. The uncertainty evaluation described here can be applied to other spectral interferometry applications based on similar principles.

Stable carbon isotope analyses of nanogram quantities of particulate organic carbon (pollen) with laser ablation nano combustion gas chromatography/isotope ratio mass spectrometry

Science.gov (United States)

Sluijs, Appy; Laks, Jelmer J.; Reichart, Gert‐Jan

2016-01-01

Rationale Analyses of stable carbon isotope ratios (δ 13C values) of organic and inorganic matter remains have been instrumental for much of our understanding of present and past environmental and biological processes. Until recently, the analytical window of such analyses has been limited to samples containing at least several μg of carbon. Methods Here we present a setup combining laser ablation, nano combustion gas chromatography and isotope ratio mass spectrometry (LA/nC/GC/IRMS). A deep UV (193 nm) laser is used for optimal fragmentation of organic matter with minimum fractionation effects and an exceptionally small ablation chamber and combustion oven are used to reduce the minimum sample mass requirement compared with previous studies. Results Analyses of the international IAEA CH‐7 polyethylene standard show optimal accuracy, and precision better than 0.5‰, when measuring at least 42 ng C. Application to untreated modern Eucalyptus globulus (C3 plant) and Zea mays (C4 plant) pollen grains shows a ~ 16‰ offset between these species. Within each single Z. mays pollen grain, replicate analyses show almost identical δ 13C values. Conclusions Isotopic offsets between individual pollen grains exceed analytical uncertainties, therefore probably reflecting interspecimen variability of ~0.5–0.9‰. These promising results set the stage for investigating both δ 13C values and natural carbon isotopic variability between single specimens of a single population of all kinds of organic particles yielding tens of nanograms of carbon. © 2016 The Authors. Rapid Communications in Mass Spectrometry Published by John Wiley & Sons Ltd. PMID:27766694

Recognizing Prefixes in Scientific Quantities

Science.gov (United States)

Sokolowski, Andrzej

2015-01-01

Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to…

30 CFR 75.322 - Harmful quantities of noxious gases.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Harmful quantities of noxious gases. 75.322... quantities of noxious gases. Concentrations of noxious or poisonous gases, other than carbon dioxide, shall... Governmental Industrial Hygienists in “Threshold Limit Values for Substance in Workroom Air” (1972). Detectors...

48 CFR 52.217-6 - Option for Increased Quantity.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Option for Increased....217-6 Option for Increased Quantity. As prescribed in 17.208(d), insert a clause substantially the same as the following: Option for Increased Quantity (MAR 1989) The Government may increase the...

41 CFR 109-27.102 - Economic order quantity principle.

Science.gov (United States)

2010-07-01

... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property...

Inventory simulation tools: Separating nuclide contributions to radiological quantities

Science.gov (United States)

Gilbert, Mark R.; Fleming, Michael; Sublet, Jean-Christophe

2017-09-01

The activation response of a material is a primary factor considered when evaluating its suitability for a nuclear application. Various radiological quantities, such as total (becquerel) activity, decay heat, and γ dose, can be readily predicted via inventory simulations, which numerically evolve in time the composition of a material under exposure to neutron irradiation. However, the resulting data sets can be very complex, often necessarily resulting in an over-simplification of the results - most commonly by just considering total response metrics. A number of different techniques for disseminating more completely the vast amount of data output from, in particular, the FISPACT-II inventory code system, including importance diagrams, nuclide maps, and primary knock-on atom (PKA) spectra, have been developed and used in scoping studies to produce database reports for the periodic table of elements. This paper introduces the latest addition to this arsenal - standardised and automated plotting of the time evolution in a radiological quantity for a given material separated by contributions from dominant radionuclides. Examples for relevant materials under predicted fusion reactor conditions, and for bench-marking studies against decay-heat measurements, demonstrate the usefulness and power of these radionuclide-separated activation plots. Note to the reader: the pdf file has been changed on September 22, 2017.

Inventory simulation tools: Separating nuclide contributions to radiological quantities

Directory of Open Access Journals (Sweden)

Gilbert Mark R.

2017-01-01

Full Text Available The activation response of a material is a primary factor considered when evaluating its suitability for a nuclear application. Various radiological quantities, such as total (becquerel activity, decay heat, and γ dose, can be readily predicted via inventory simulations, which numerically evolve in time the composition of a material under exposure to neutron irradiation. However, the resulting data sets can be very complex, often necessarily resulting in an over-simplification of the results – most commonly by just considering total response metrics. A number of different techniques for disseminating more completely the vast amount of data output from, in particular, the FISPACT-II inventory code system, including importance diagrams, nuclide maps, and primary knock-on atom (PKA spectra, have been developed and used in scoping studies to produce database reports for the periodic table of elements. This paper introduces the latest addition to this arsenal – standardised and automated plotting of the time evolution in a radiological quantity for a given material separated by contributions from dominant radionuclides. Examples for relevant materials under predicted fusion reactor conditions, and for bench-marking studies against decay-heat measurements, demonstrate the usefulness and power of these radionuclide-separated activation plots.

Photosynthesis-related quantities for education and modeling.

Science.gov (United States)

Antal, Taras K; Kovalenko, Ilya B; Rubin, Andrew B; Tyystjärvi, Esa

2013-11-01

A quantitative understanding of the photosynthetic machinery depends largely on quantities, such as concentrations, sizes, absorption wavelengths, redox potentials, and rate constants. The present contribution is a collection of numbers and quantities related mainly to photosynthesis in higher plants. All numbers are taken directly from a literature or database source and the corresponding reference is provided. The numerical values, presented in this paper, provide ranges of values, obtained in specific experiments for specific organisms. However, the presented numbers can be useful for understanding the principles of structure and function of photosynthetic machinery and for guidance of future research.

Category 3 threshold quantities for hazard categorization of nonreactor facilities

International Nuclear Information System (INIS)

Mandigo, R.L.

1996-01-01

This document provides the information necessary to determine Hazard Category 3 threshold quantities for those isotopes of interest not listed in WHC-CM-4-46, Section 4, Table 1.''Threshold Quantities.''

The Quantity and Quality of Illegally Imported Products of Animal Origin in Personal Consignments into the European Union Seized at Two German Airports between 2010 And 2014.

Directory of Open Access Journals (Sweden)

Wiebke Jansen

Full Text Available The import of products of animal origin (POAO in travellers' personal consignments presents a considerable risk of introducing animal diseases and emerging zoonoses into the European Union. The current regulation (EU 206/2009 implements strict measures for illegally imported POAO, whereupon non-complying products have to be seized and destroyed regardless. Especially airports serve as global bottlenecks for illegally imported POAO where passenger controls of non-European flights are performed by customs and veterinary services in collaboration. Results of these control measures have to be submitted in the form of annual reports to the European Commission. However, few data on qualities and quantities of seizures have been published so far. In this study, POAO seized at two German airports between 2010 and 2014 were analysed in terms of quantities, qualitative categories and region of origin. In most years considered, more than 20 tonnes POAO were seized at each airport. However, reported amounts of seizures seem to be only the tip of the iceberg as an all-passenger control is not feasible and therefore travellers are only spot-checked. The analysis suggests that the organisational structures of both customs and official veterinary services and their different risk perceptions interfere in completing an effective ban on the illegal import of POAO.

19 CFR 144.33 - Minimum quantities to be withdrawn.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Minimum quantities to be withdrawn. 144.33 Section 144.33 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT... Warehouse § 144.33 Minimum quantities to be withdrawn. Unless by special authority of the Commissioner of...

Quantity Estimation Of The Interactions

International Nuclear Information System (INIS)

Gorana, Agim; Malkaj, Partizan; Muda, Valbona

2007-01-01

In this paper we present some considerations about quantity estimations, regarding the range of interaction and the conservations laws in various types of interactions. Our estimations are done under classical and quantum point of view and have to do with the interaction's carriers, the radius, the influence range and the intensity of interactions

Information quantity in a pixel of digital image

OpenAIRE

Kharinov, M.

2014-01-01

The paper is devoted to the problem of integer-valued estimating of information quantity in a pixel of digital image. The definition of an integer estimation of information quantity based on constructing of the certain binary hierarchy of pixel clusters is proposed. The methods for constructing hierarchies of clusters and generating of hierarchical sequences of image approximations that minimally differ from the image by a standard deviation are developed. Experimental results on integer-valu...

Processing ordinality and quantity: the case of developmental dyscalculia.

Directory of Open Access Journals (Sweden)

Orly Rubinsten

Full Text Available In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1 the traditionally and well accepted numerical magnitude system but also (2 core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD. Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1 and 3 numbers (symbolic task: Experiment 2. In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks, DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

Processing ordinality and quantity: the case of developmental dyscalculia.

Science.gov (United States)

Rubinsten, Orly; Sury, Dana

2011-01-01

In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

What difference does quantity make? On the epistemology of Big Data in biology

Directory of Open Access Journals (Sweden)

S Leonelli

2014-07-01

Full Text Available Is Big Data science a whole new way of doing research? And what difference does data quantity make to knowledge production strategies and their outputs? I argue that the novelty of Big Data science does not lie in the sheer quantity of data involved, but rather in (1 the prominence and status acquired by data as commodity and recognised output, both within and outside of the scientific community and (2 the methods, infrastructures, technologies, skills and knowledge developed to handle data. These developments generate the impression that data-intensive research is a new mode of doing science, with its own epistemology and norms. To assess this claim, one needs to consider the ways in which data are actually disseminated and used to generate knowledge. Accordingly, this article reviews the development of sophisticated ways to disseminate, integrate and re-use data acquired on model organisms over the last three decades of work in experimental biology. I focus on online databases as prominent infrastructures set up to organise and interpret such data and examine the wealth and diversity of expertise, resources and conceptual scaffolding that such databases draw upon. This illuminates some of the conditions under which Big Data needs to be curated to support processes of discovery across biological subfields, which in turn highlights the difficulties caused by the lack of adequate curation for the vast majority of data in the life sciences. In closing, I reflect on the difference that data quantity is making to contemporary biology, the methodological and epistemic challenges of identifying and analysing data given these developments, and the opportunities and worries associated with Big Data discourse and methods.

Foreign materials in the repository. Update of estimated quantities

International Nuclear Information System (INIS)

Karvonen, T.

2011-06-01

A variety of materials are used during the construction process and the operation of the repository for spent nuclear fuel at Olkiluoto in Eurajoki, Finland. In addition to materials necessary for the construction and operation, some materials may be transported into the repository with the ventilation air, as emissions from vehicles etc. Both of these two types of materials are considered here and both introduced quantities and the quantities that remain after the closure in the repository are estimated here based on the most recent information. This work is intended to update the previous estimations, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility called ONKALO at Olkiluoto. The implemented quantities as well as designs and preliminary designs have been used in calculating the quantities of the foreign materials. The estimations made in this report are specific to a KBS-3V type repository. In some cases more generic information has been used, particularly when the relevant quantities have not been monitored in ONKALO. The estimations are based on the new repository layout produced in 2010 and consider the latest plans for grouting and rock support. As all of these plans are not final some quantities may change in the future. As the repository layout may still go through some changes this report also provides the foreign materials for a hundred meters of different deposition tunnels designed for the OL and LO type canisters1. The results have also been calculated for a space demanded by a deposition tunnel end plug and the tunnel lengths before and after one. The most significant foreign materials are certain accessory minerals of the clay materials followed by organic materials (including the organic carbon from the clay materials), cement, steel and silica. (orig.)

Conserved quantities for generalized KdV equations

International Nuclear Information System (INIS)

Calogero, F.; Rome Univ.; Degasperis, A.; Rome Univ.

1980-01-01

It is noted that the nonlinear evolution equation usub(t) = α(t)usub(xxx) - 6ν(t) usub(x)u, u is identical to u(x,t), possesses three (and, in some cases, four) conserved quantities, that are explicitly displayed. These results are of course relevant only to the cases in which this evolution equation is not known to possess an infinite number of conserved quantities. Purpose and scope of this paper is to report three or four simple conservation laws possessed by the evolution equation usub(t) = α(t)usub(xxx) - 6ν(t)usub(x)u, u is identical to u(x,t). (author)

A geochemical module for "AMDTreat" to compute caustic quantity, effluent quantity, and sludge volume

Science.gov (United States)

Cravotta,, Charles A.; Parkhurst, David L.; Means, Brent P; McKenzie, Bob; Morris, Harry; Arthur, Bill

2010-01-01

Treatment with caustic chemicals typically is used to increase pH and decrease concentrations of dissolved aluminum, iron, and/or manganese in largevolume, metal-laden discharges from active coal mines. Generally, aluminum and iron can be removed effectively at near-neutral pH (6 to 8), whereas active manganese removal requires treatment to alkaline pH (~10). The treatment cost depends on the specific chemical used (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) and increases with the quantities of chemical added and sludge produced. The pH and metals concentrations do not change linearly with the amount of chemical added. Consequently, the amount of caustic chemical needed to achieve a target pH and the corresponding effluent composition and sludge volume can not be accurately determined without empirical titration data or the application of geochemical models to simulate the titration of the discharge water with caustic chemical(s). The AMDTreat computer program (http://amd.osmre.gov/ ) is widely used to compute costs for treatment of coal-mine drainage. Although AMDTreat can use results of empirical titration with industrial grade caustic chemicals to compute chemical costs for treatment of net-acidic or net-alkaline mine drainage, such data are rarely available. To improve the capability of AMDTreat to estimate (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the concentrations of dissolved metals in treated effluent, and (3) the volume of sludge produced by the treatment, a titration simulation is being developed using the geochemical program PHREEQC (wwwbrr.cr.usgs.gov/projects/GWC_coupled/phreeqc/) that will be coupled as a module to AMDTreat. The simulated titration results can be compared with or used in place of empirical titration data to estimate chemical quantities and costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module for AMDTreat.

The IBAS image analyser and its use in particle size measurement

International Nuclear Information System (INIS)

Snelling, K.W.

1984-10-01

The Kontron image analyser (IBAS) is used at Winfrith primarily for size analysis of aerosol particles. The system incorporates two computers, IBAS 1 for system communication and control, and IBAS 2 containing the main image memories. The first is accessed via a keyboard or digitiser tablet, and output can be displayed on a monitor or in printed form. The contents of the image memories are displayed on a colour monitor. Automatic image analysis is described, with typical applications, including the measurement of monodisperse particles, sodium fire aerosols, reactor crud particles and cadmium-silver aerosol particles. (U.K.)

Establishment and Evaluation of Decommissioning Plant Inventory DB and Waste Quantity

International Nuclear Information System (INIS)

Oh, Jae Yong; Moon, Sang-Rae; Yun, Taesik; Kim, Hee-Geun; Sung, Nak-Hoon; Jung, Seung Hyuk

2016-01-01

Korea Hydro and Nuclear Power (KHNP) made a decision for permanent shutdown of Kori-1 and has progressed the strategy determination and R and D for the decommissioning of Kori-1. Decommissioning waste, Structure, System and Components (SSCs) is one of the most important elements. Decommissioning waste quantity is calculated based on Plant Inventory Database (PI DB) with activation and contamination data. Due to the largest portion of waste management and disposal in decommissioning, it is necessary to exactly evaluate waste quantity (applying the regulation, guideline and site-specific characterization) for economic feasibility. In this paper, construction of PI DB and evaluation of waste quantity for Optimized Pressurized Reactor (OPR-1000) are mainly described. Decommissioning waste quantities evaluated are going to be applied to calculation of the project cost. In fact, Ministry of Trade, Industry and Energy (MOTIE) in Korea expected the decommissioning waste quantity in a range of 14,500-18,850 drums, and predicted appropriate liability for decommissioning fund by using waste quantity. The result of this study is also computed by the range of 14,500-18,850 drums. Since there is no site-specific data for the NPP site, this evaluation is the preliminary analysis

Establishment and Evaluation of Decommissioning Plant Inventory DB and Waste Quantity

Energy Technology Data Exchange (ETDEWEB)

Oh, Jae Yong; Moon, Sang-Rae; Yun, Taesik; Kim, Hee-Geun [KHNP CRI, Daejeon (Korea, Republic of); Sung, Nak-Hoon; Jung, Seung Hyuk [KONES Corp., Seoul (Korea, Republic of)

2016-10-15

Korea Hydro and Nuclear Power (KHNP) made a decision for permanent shutdown of Kori-1 and has progressed the strategy determination and R and D for the decommissioning of Kori-1. Decommissioning waste, Structure, System and Components (SSCs) is one of the most important elements. Decommissioning waste quantity is calculated based on Plant Inventory Database (PI DB) with activation and contamination data. Due to the largest portion of waste management and disposal in decommissioning, it is necessary to exactly evaluate waste quantity (applying the regulation, guideline and site-specific characterization) for economic feasibility. In this paper, construction of PI DB and evaluation of waste quantity for Optimized Pressurized Reactor (OPR-1000) are mainly described. Decommissioning waste quantities evaluated are going to be applied to calculation of the project cost. In fact, Ministry of Trade, Industry and Energy (MOTIE) in Korea expected the decommissioning waste quantity in a range of 14,500-18,850 drums, and predicted appropriate liability for decommissioning fund by using waste quantity. The result of this study is also computed by the range of 14,500-18,850 drums. Since there is no site-specific data for the NPP site, this evaluation is the preliminary analysis.

Uncertainty evaluation in correlated quantities: application to elemental analysis of atmospheric aerosols

International Nuclear Information System (INIS)

Espinosa, A.; Miranda, J.; Pineda, J. C.

2010-01-01

One of the aspects that are frequently overlooked in the evaluation of uncertainty in experimental data is the possibility that the involved quantities are correlated among them, due to different causes. An example in the elemental analysis of atmospheric aerosols using techniques like X-ray Fluorescence (X RF) or Particle Induced X-ray Emission (PIXE). In these cases, the measured elemental concentrations are highly correlated, and then are used to obtain information about other variables, such as the contribution from emitting sources related to soil, sulfate, non-soil potassium or organic matter. This work describes, as an example, the method required to evaluate the uncertainty in variables determined from correlated quantities from a set of atmospheric aerosol samples collected in the Metropolitan Area of the Mexico Valley and analyzed with PIXE. The work is based on the recommendations of the Guide for the Evaluation of Uncertainty published by the International Organization for Standardization. (Author)

Measurement of electromagnetic fields generated by air traffic control radar systems with spectrum analysers.

Science.gov (United States)

Barellini, A; Bogi, L; Licitra, G; Silvi, A M; Zari, A

2009-12-01

Air traffic control (ATC) primary radars are 'classical' radars that use echoes of radiofrequency (RF) pulses from aircraft to determine their position. High-power RF pulses radiated from radar antennas may produce high electromagnetic field levels in the surrounding area. Measurement of electromagnetic fields produced by RF-pulsed radar by means of a swept-tuned spectrum analyser are investigated here. Measurements have been carried out both in the laboratory and in situ on signals generated by an ATC primary radar.

Measurement of electromagnetic fields generated by air traffic control radar systems with spectrum analysers

International Nuclear Information System (INIS)

Barellini, A.; Bogi, L.; Licitra, G.; Silvi, A. M.; Zari, A.

2009-01-01

Air traffic control (ATC) primary radars are 'classical' radars that use echoes of radiofrequency (RF) pulses from aircraft to determine their position. High-power RF pulses radiated from radar antennas may produce high electromagnetic field levels in the surrounding area. Measurement of electromagnetic fields produced by RF-pulsed radar by means of a swept-tuned spectrum analyser are investigated here. Measurements have been carried out both in the laboratory and in situ on signals generated by an ATC primary radar. (authors)

Parents face quantity-quality trade-offs between reproduction and investment in offspring in Iceland.

Science.gov (United States)

Lynch, Robert Francis

2016-05-01

How to optimally allocate time, energy and investment in an effort to maximize one's reproductive success is a fundamental problem faced by all organisms. This effort is complicated when the production of each additional offspring dilutes the total resources available for parental investment. Although a quantity-quality trade-off between producing and investing in offspring has long been assumed in evolutionary biology, testing it directly in humans is difficult, partly owing to the long generation time of our species. Using data from an Icelandic genealogy (Íslendingabók) over two centuries, I address this issue and analyse the quantity-quality trade-off in humans. I demonstrate that the primary impact of parents on the fitness of their children is the result of resources and or investment, but not genes. This effect changes significantly across time, in response to environmental conditions. Overall, increasing reproduction has negative fitness consequences on offspring, such that each additional sibling reduces an individual's average lifespan and lifetime reproductive success. This analysis provides insights into the evolutionary conflict between producing and investing in children while also shedding light on some of the causes of the demographic transition.

Comparative biochemical analyses of venous blood and peritoneal fluid from horses with colic using a portable analyser and an in-house analyser.

Science.gov (United States)

Saulez, M N; Cebra, C K; Dailey, M

2005-08-20

Fifty-six horses with colic were examined over a period of three months. The concentrations of glucose, lactate, sodium, potassium and chloride, and the pH of samples of blood and peritoneal fluid, were determined with a portable clinical analyser and with an in-house analyser and the results were compared. Compared with the in-house analyser, the portable analyser gave higher pH values for blood and peritoneal fluid with greater variability in the alkaline range, and lower pH values in the acidic range, lower concentrations of glucose in the range below 8.3 mmol/l, and lower concentrations of lactate in venous blood in the range below 5 mmol/l and in peritoneal fluid in the range below 2 mmol/l, with less variability. On average, the portable analyser underestimated the concentrations of lactate and glucose in peritoneal fluid in comparison with the in-house analyser. Its measurements of the concentrations of sodium and chloride in peritoneal fluid had a higher bias and were more variable than the measurements in venous blood, and its measurements of potassium in venous blood and peritoneal fluid had a smaller bias and less variability than the measurements made with the in-house analyser.

Comparison of an infrared anaesthetic agent analyser (Datex-Ohmeda) with refractometry for measurement of isoflurane, sevoflurane and desflurane concentrations.

Science.gov (United States)

Rudolff, Andrea S; Moens, Yves P S; Driessen, Bernd; Ambrisko, Tamas D

2014-07-01

To assess agreement between infrared (IR) analysers and a refractometer for measurements of isoflurane, sevoflurane and desflurane concentrations and to demonstrate the effect of customized calibration of IR analysers. In vitro experiment. Six IR anaesthetic monitors (Datex-Ohmeda) and a single portable refractometer (Riken). Both devices were calibrated following the manufacturer's recommendations. Gas samples were collected at common gas outlets of anaesthesia machines. A range of agent concentrations was produced by stepwise changes in dial settings: isoflurane (0-5% in 0.5% increments), sevoflurane (0-8% in 1% increments), or desflurane (0-18% in 2% increments). Oxygen flow was 2 L minute(-1) . The orders of testing IR analysers, agents and dial settings were randomized. Duplicate measurements were performed at each setting. The entire procedure was repeated 24 hours later. Bland-Altman analysis was performed. Measurements on day-1 were used to yield calibration equations (IR measurements as dependent and refractometry measurements as independent variables), which were used to modify the IR measurements on day-2. Bias ± limits of agreement for isoflurane, sevoflurane and desflurane were 0.2 ± 0.3, 0.1 ± 0.4 and 0.7 ± 0.9 volume%, respectively. There were significant linear relationships between differences and means for all agents. The IR analysers became less accurate at higher gas concentrations. After customized calibration, the bias became almost zero and the limits of agreement became narrower. If similar IR analysers are used in research studies, they need to be calibrated against a reference method using the agent in question at multiple calibration points overlapping the range of interest. © 2013 Association of Veterinary Anaesthetists and the American College of Veterinary Anesthesia and Analgesia.

29 CFR 780.814 - “Grown in commercial quantities.”

Science.gov (United States)

2010-07-01

... OF GENERAL POLICY OR INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF AGRICULTURAL COMMODITIES, AND RELATED SUBJECTS UNDER THE FAIR LABOR STANDARDS ACT... “commercial” quantities, the trade understanding of what are “commercial” quantities of cotton would be...

MEAL-BASED ENHANCEMENT OF PROTEIN QUALITY AND QUANTITY DURING WEIGHT LOSS IN OBESE OLDER ADULTS WITH MOBILITY LIMITATIONS: RATIONALE AND DESIGN FOR THE MEASUR-UP TRIAL

Science.gov (United States)

McDonald, Shelley R.; Starr, Kathryn N. Porter; Mauceri, Luisa; Orenduff, Melissa; Granville, Esther; Ocampo, Christine; Payne, Martha E.; Pieper, Carl F.; Bales, Connie W.

2015-01-01

Obese older adults with even modest functional limitations are at a disadvantage for maintaining their independence into late life. However, there is no established intervention for obesity in older individuals. The Measuring Eating, Activity and Strength: Understanding the Response --Using Protein (MEASUR-UP) trial is a randomized controlled pilot study of obese women and men aged ≥60 years with mild to moderate functional impairments. Changes in body composition (lean and fat mass) and function (Short Physical Performance Battery) in an enhanced protein weight reduction (Protein) arm will be compared to those in a traditional weight loss (Control) arm. The Protein intervention is based on evidence that older adults achieve optimal rates of muscle protein synthesis when consuming about 25-30 grams of high quality protein per meal; these participants will consume −30 g of animal protein at each meal via a combination of provided protein (beef) servings and diet counseling. This trial will provide information on the feasibility and efficacy of enhancing protein quantity and quality in the context of a weight reduction regimen and determine the impact of this intervention on body weight, functional status, and lean muscle mass. We hypothesize that the enhancement of protein quantity and quality in the Protein arm will result in better outcomes for function and/or lean muscle mass than in the Control arm. Ultimately, we hope our findings will help identify a safe weight loss approach that can delay or prevent late life disability by changing the trajectory of age-associated functional impairment associated with obesity. PMID:25461495

Sleep and its association with aggression among prisoners: Quantity or quality?

Science.gov (United States)

Barker, Lyndsie Fiona; Ireland, Jane L; Chu, Simon; Ireland, Carol A

2016-01-01

The current paper aims to examine the association between self-reported sleep quality and quantity and how these relate to aggression motivation and hostile cognition in a male prisoner sample. The cognitive component of sleep, namely perception, is consequently a variable of particular interest and one neglected by previous research. Two independent studies are presented. The first comprised 95 adult male prisoners who completed a sleep quality index along with measures of implicit and explicit aggression. The second study extended this to consider aggression motivation and hostile attribution biases using a sample of 141 young male adult prisoners. In study one, sleep quantity and indicators of sleep quality were found not to associate with aggression whereas the perception of poor sleep did; those perceiving poor sleep quality were more likely than those perceiving good sleep to report they had perpetrated aggression in the previous week and to report higher levels of implicit aggression. Study two found that while increased indicators of poor sleep quality were associated with lower prosocial attribution tendencies and higher levels of reactive and proactive aggression, sleep quantity was not associated. The perception of poor quality sleep was important; those perceiving poor sleep were more likely to report higher levels of reactive and proactive aggression than those reporting good sleep. Collectively the studies highlight the importance of accounting for the perception of sleep quality as an important cognitive component in understanding the association between sleep and aggression. Copyright © 2016 Elsevier Ltd. All rights reserved.

Automatic apparatus for measuring thermophysical quantities controlled by calculator EMG 666

International Nuclear Information System (INIS)

Kubicar, L.; Illekova, E.

1984-01-01

Automatic system for measuring thermal diffusivity, thermal conductivity and heat capacity of samples is described. Measurements are performed by the pulse method in the temperature range from -150 to 1500 deg C. The measuring CAMAC equipment connected with the EMG 666 computer. Data processing is carried out by 100-400 measurement points (measuring cycle) for the whole temperature range

Determination of very small contents of boron by pH difference measurement

International Nuclear Information System (INIS)

Boehm, H.; Kirmse, E.M.; Schilbach, U.

1983-01-01

For the determination of boron as a trace element for food of plants in a very complicated salt matrix an analytical proceeding was developed, which allows to determine the content of boron without separation. The principle of analysis is based on the esterification of boric acid with a multivalent alcohol, which leeds to a monovalent strong complex acid. The change of the pH value of the analysing solution is measured. From the initial pH number, the end pH number, the volume of the analysing solution and the ionic product of water corresponding with the operating temperature the quantity of boric acid of boron that is equivalent the produced quantity of H + -ions is calculated by means of a linear program. The standard deviation of analytical proceeding amounts to 13.9 ng B. For the determination of the contents of boron of an unknown sample, five to ten separate measurements are carried out. For solutions, which are about 1x10 -6 M of boric acid, there are necessary 10 ml of sample for each separate measurement. The confidence interval of analytical results is found to be between +- 0.5 and +- 15.5% (P=0.99). For the determination of the content of boron in plant materials about 50-100 mg of dry weight are necessary. (Author)

Entry-Item-Quantity-ABC Analysis-Based Multitype Cigarette Fast Sorting System

Directory of Open Access Journals (Sweden)

Ying Zhao

2012-01-01

Full Text Available Numerous items, small order, and frequent delivery are the characteristics of many distribution centers. Such characteristics generally increase the operating costs of the distribution center. To remedy this problem, this study employs the Entry-Item-Quantity (EIQ method to identify the characteristic of the cigarette distribution center and further analyzes the importance degree of customers and the frequently ordered products by means of EQ/EN/IQ-B/IK statistic charts. Based on these analyses as well as the total replenishment cost optimization model, multipicking strategies and combined multitype picking equipment allocation is then formulated accordingly. With such design scheme, the cigarette picking costs of the distribution center are expected to reduce. Finally, the specific number of equipment is figured out in order to meet the capability demand of the case cigarette distribution center.

Radiation quantities and units. ICRU report 33

International Nuclear Information System (INIS)

Anon.

1987-01-01

This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. It is recommended that energy state be inserted into the definition of activity and that the word transformation be replaced by transition. These modifications have now been incorporated into the current definition. Helpful comments on the previous quantities and units report have resulted in clarification of several points in the present Report. In line with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection I.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. 11 refs., 4 tabs

Trained Quantity Abilities in Horses (Equus caballus: A Preliminary Investigation

Directory of Open Access Journals (Sweden)

Maria Elena Miletto Petrazzini

2014-07-01

Full Text Available Once believed to be a human prerogative, the capacity to discriminate between quantities now has also been reported in several vertebrates. To date, only two studies investigated numerical abilities in horses (Equus caballus but reported contrasting data. To assess whether horses can be trained to discriminate between quantities, I have set up a new experimental protocol using operant conditioning. One adult female was trained to discriminate between 1 and 4 (Test 1 in three different conditions: non-controlled continuous variables (numerical and continuous quantities that co-vary with number are simultaneously available, 50% controlled continuous variables (intermediate condition, and 100% controlled continuous variables (only numerical information available. The subject learned the discrimination in all conditions, showing the capacity to process numerical information. When presented with a higher numerical ratio (2 vs. 4, Test 2, the subject still discriminated between the quantities but its performance was statistically significant only in the non-controlled condition, suggesting that the subject used multiple cues in presence of a more difficult discrimination. On the whole, the results here reported encourage the use of this experimental protocol as a valid tool to investigate the capacity to process numerical and continuous quantities in horses in future research.

On the Output-Inflation Relationship When Price and Quantity Adjustments are Costly

DEFF Research Database (Denmark)

Danziger, Leif; Kreiner, Claus Thustrup

A vast literature analyzes the real effects of price-adjustment costs assuming that quantity adjustments are costless. In this paper, we analyze whether the presence of quantity-adjustments costs, which presumably are significant, change the traditional results on the impact of inflation....... In particular, recent findings suggest that quantity-adjustment costs may remove the linkage between output and inflation. We show that this is not the case when inflation is anticipated. On the contrary, quantity-adjustment costs may significantly amplify the consequences of price-adjustment costs...

Experimental study of quantity to be taken as patient dose in helical multi-slice CT scan

International Nuclear Information System (INIS)

Liu Lantao; Wei Kedao; Yue Brorong; Wang Jianchao

2009-01-01

Objective: To bring forward a novel quantity which is used to be taken as effective dose in helical multi - slice CT scan and to validate it by experiment. Methods: Dot chamber and pencil-chamber were used to measure the doses which were performed under axial mode and helical multi-slice mode. Then the readings of doses were compared and analyzed. Results: The dose reading from dot chamber was close to the one from pencil - chamber under axial mode. The ratio is 1.14 for the readings from dot chamber under two scan modes and is 2.88 for the readings from pencil-chamber under two scan modes. Conclusions: The dose measured from dot chamber is an effective quantity to be taken as effective dose. However it is insufficient that the CTDI and DLP be used to be taken as effective dose as the limitation of pencil-chamber in length. (authors)

Not Normal: the uncertainties of scientific measurements

Science.gov (United States)

Bailey, David C.

2017-01-01

Judging the significance and reproducibility of quantitative research requires a good understanding of relevant uncertainties, but it is often unclear how well these have been evaluated and what they imply. Reported scientific uncertainties were studied by analysing 41 000 measurements of 3200 quantities from medicine, nuclear and particle physics, and interlaboratory comparisons ranging from chemistry to toxicology. Outliers are common, with 5σ disagreements up to five orders of magnitude more frequent than naively expected. Uncertainty-normalized differences between multiple measurements of the same quantity are consistent with heavy-tailed Student's t-distributions that are often almost Cauchy, far from a Gaussian Normal bell curve. Medical research uncertainties are generally as well evaluated as those in physics, but physics uncertainty improves more rapidly, making feasible simple significance criteria such as the 5σ discovery convention in particle physics. Contributions to measurement uncertainty from mistakes and unknown problems are not completely unpredictable. Such errors appear to have power-law distributions consistent with how designed complex systems fail, and how unknown systematic errors are constrained by researchers. This better understanding may help improve analysis and meta-analysis of data, and help scientists and the public have more realistic expectations of what scientific results imply.

Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

Energy Technology Data Exchange (ETDEWEB)

Hagros, Annika (Sannio and Riekkola OY (Finland))

2008-12-15

The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

International Nuclear Information System (INIS)

Hagros, Annika

2008-12-01

The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

A statistical law in the perception of risks and physical quantities in traffic

DEFF Research Database (Denmark)

Elvik, Rune

2015-01-01

This paper suggests that a universal psychophysical law influences the perception of risks and physical quantities in traffic. This law states that there will be a tendency to overestimate low probabilities or small quantities, while high probabilities or large quantities may be underestimated....... Studies of the perception of risk and physical quantities in traffic have found a highly consistent pattern....

Entropy and Its Correlations with Other Related Quantities

Directory of Open Access Journals (Sweden)

Jing Wu

2014-02-01

Full Text Available In order to find more correlations between entropy and other related quantities, an analogical analysis is conducted between thermal science and other branches of physics. Potential energy in various forms is the product of a conserved extensive quantity (for example, mass or electric charge and an intensive quantity which is its potential (for example, gravitational potential or electrical voltage, while energy in specific form is a dissipative quantity during irreversible transfer process (for example mechanical or electrical energy will be dissipated as thermal energy. However, it has been shown that heat or thermal energy, like mass or electric charge, is conserved during heat transfer processes. When a heat transfer process is for object heating or cooling, the potential of internal energy U is the temperature T and its potential “energy” is UT/2 (called entransy and it is the simplified expression of thermomass potential energy; when a heat transfer process is for heat-work conversion, the potential of internal energy U is (1 − T0/T, and the available potential energy of a system in reversible heat interaction with the environment is U − U0 − T0(S − S0, then T0/T and T0(S − S0 are the unavailable potential and the unavailable potential energy of a system respectively. Hence, entropy is related to the unavailable potential energy per unit environmental temperature for heat-work conversion during reversible heat interaction between the system and its environment. Entropy transfer, like other forms of potential energy transfer, is the product of the heat and its potential, the reciprocal of temperature, although it is in form of the quotient of the heat and the temperature. Thus, the physical essence of entropy transfer is the unavailable potential energy transfer per unit environmental temperature. Entropy is a non-conserved, extensive, state quantity of a system, and entropy generation in an irreversible heat transfer process

How much is too much? The effects of information quantity on crowdfunding performance.

Science.gov (United States)

Moy, Naomi; Chan, Ho Fai; Torgler, Benno

2018-01-01

We explore the effects of the quantity of information on the tendency to contribute to crowdfunding campaigns. Using the crowdfunding platform Kickstarter, we analyze the campaign descriptions and the performance of over 70,000 projects. We look empirically at the effect of information quantity (word count) on funding success (as measure by amount raised and number of backers). Within this empirical approach, we test whether an excessive amount of information will affect funding success. To do so, we test for the non-linearity (quadratic) effect of our independent variable (word count) using regression analysis. Consistent with the hypothesis that excess information will negatively affect funds raised and number of contributors, we observe a consistent U-shaped relationship between campaign text length and overall success which suggest that an optimal number of words exists within crowdfunding texts and that going over this point will reduce a project's chance of fundraising success.

A wireless interrogation system exploiting narrowband acoustic resonator for remote physical quantity measurement

Energy Technology Data Exchange (ETDEWEB)

Friedt, J.-M [SENSeOR, 32 Avenue de l' Observatoire, 25044 Besancon (France); Droit, C.; Martin, G.; Ballandras, S. [Department of Time and Frequency, FEMTO-ST, 32 Avenue de l' Observatoire, 25044 Besancon (France)

2010-01-15

Monitoring physical quantities using acoustic wave devices can be advantageously achieved using the wave characteristic dependence to various parametric perturbations (temperature, stress, and pressure). Surface acoustic wave (SAW) resonators are particularly well suited to such applications as their resonance frequency is directly influenced by these perturbations, modifying both the phase velocity and resonance conditions. Moreover, the intrinsic radio frequency (rf) nature of these devices makes them ideal for wireless applications, mainly exploiting antennas reciprocity and piezoelectric reversibility. In this paper, we present a wireless SAW sensor interrogation unit operating in the 434 MHz centered ISM band--selected as a tradeoff between antenna dimensions and electromagnetic wave penetration in dielectric media--based on the principles of a frequency sweep network analyzer. We particularly focus on the compliance with the ISM standard which reveals complicated by the need for switching from emission to reception modes similarly to radar operation. In this matter, we propose a fully digital rf synthesis chain to develop various interrogation strategies to overcome the corresponding difficulties and comply with the above-mentioned standard. We finally assess the reader interrogation range, accuracy, and dynamics.

A wireless interrogation system exploiting narrowband acoustic resonator for remote physical quantity measurement

International Nuclear Information System (INIS)

Friedt, J.-M; Droit, C.; Martin, G.; Ballandras, S.

2010-01-01

Monitoring physical quantities using acoustic wave devices can be advantageously achieved using the wave characteristic dependence to various parametric perturbations (temperature, stress, and pressure). Surface acoustic wave (SAW) resonators are particularly well suited to such applications as their resonance frequency is directly influenced by these perturbations, modifying both the phase velocity and resonance conditions. Moreover, the intrinsic radio frequency (rf) nature of these devices makes them ideal for wireless applications, mainly exploiting antennas reciprocity and piezoelectric reversibility. In this paper, we present a wireless SAW sensor interrogation unit operating in the 434 MHz centered ISM band--selected as a tradeoff between antenna dimensions and electromagnetic wave penetration in dielectric media--based on the principles of a frequency sweep network analyzer. We particularly focus on the compliance with the ISM standard which reveals complicated by the need for switching from emission to reception modes similarly to radar operation. In this matter, we propose a fully digital rf synthesis chain to develop various interrogation strategies to overcome the corresponding difficulties and comply with the above-mentioned standard. We finally assess the reader interrogation range, accuracy, and dynamics.

Mapping spatio-temporal variation of grassland quantity and quality using MERIS data and the PROSAIL model

NARCIS (Netherlands)

Si, Y.; Schlerf, M.; Zurita-Milla, R.; Skidmore, A.K.; Wang, T.

2012-01-01

Accurate estimates of the quantity and quality of grasslands, as they vary in space and time and from regional to global scales, furthers our understanding of grassland ecosystems. The Medium Resolution Imaging Spectrometer (MERIS) is a promising sensor for measuring and monitoring grasslands due to

Practicable methods for histological section thickness measurement in quantitative stereological analyses.

Science.gov (United States)

Matenaers, Cyrill; Popper, Bastian; Rieger, Alexandra; Wanke, Rüdiger; Blutke, Andreas

2018-01-01

The accuracy of quantitative stereological analysis tools such as the (physical) disector method substantially depends on the precise determination of the thickness of the analyzed histological sections. One conventional method for measurement of histological section thickness is to re-embed the section of interest vertically to its original section plane. The section thickness is then measured in a subsequently prepared histological section of this orthogonally re-embedded sample. However, the orthogonal re-embedding (ORE) technique is quite work- and time-intensive and may produce inaccurate section thickness measurement values due to unintentional slightly oblique (non-orthogonal) positioning of the re-embedded sample-section. Here, an improved ORE method is presented, allowing for determination of the factual section plane angle of the re-embedded section, and correction of measured section thickness values for oblique (non-orthogonal) sectioning. For this, the analyzed section is mounted flat on a foil of known thickness (calibration foil) and both the section and the calibration foil are then vertically (re-)embedded. The section angle of the re-embedded section is then calculated from the deviation of the measured section thickness of the calibration foil and its factual thickness, using basic geometry. To find a practicable, fast, and accurate alternative to ORE, the suitability of spectral reflectance (SR) measurement for determination of plastic section thicknesses was evaluated. Using a commercially available optical reflectometer (F20, Filmetrics®, USA), the thicknesses of 0.5 μm thick semi-thin Epon (glycid ether)-sections and of 1-3 μm thick plastic sections (glycolmethacrylate/ methylmethacrylate, GMA/MMA), as regularly used in physical disector analyses, could precisely be measured within few seconds. Compared to the measured section thicknesses determined by ORE, SR measures displayed less than 1% deviation. Our results prove the applicability

Import and export of small quantities of nuclear materials

International Nuclear Information System (INIS)

Grenier, M.

1986-06-01

Administrative procedures for import export of nuclear materials are specific for each country. In France regulations are reviewed for small quantities, lower threshold, in some cases, allows a simplified procedure, however thresholds are not the same in the different texts (and for one of them, concerning proliferation, is zero). It is obvious that regulations are necessary even for small quantities but national and international threshold should be harmonized [fr

Quantity, size and distribution of borides for aluminium grain refinement by neutron-induced autoradiography (NIAR). Pt. 2

International Nuclear Information System (INIS)

Rachlitz, R.; Gaertner, S.; Holze, J.; Krumnacker, M.

1990-01-01

Al-Ti-B grain refiners improve the cast structure of aluminium and its alloys, but also cause problems related to the great hardness of the borides and their tendency to agglomerate and settle. Accurate information about the distribution, quantity and size of the TiB 2 particles is needed if material properties are to be improved and the quantity of additives minimized. This information is obtained mostly by NIAR. In laboratory-scale tests Al 99.8 and Al 99.5 were refined using different master alloys added in various quantities. In all cases the commercial master alloy gave the best refining effect. Besides boride particle size distribution and the presence of nuclei and nucleus stabilizers, morphological properties (duplex particles) are obviously of essential importance. It has been demonstrated that the TiB 2 size distribution values determined by NIAR are comparable with those established by optical microscopy measurements. (orig.) [de

7 CFR 35.13 - Minimum quantity.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Minimum quantity. 35.13 Section 35.13 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... part, transport or receive for transportation to any foreign destination, a shipment of 25 packages or...

Process of quantity determination of uranium by chromatography in liquid zone

International Nuclear Information System (INIS)

Muller, J.P.; Cojean, J.; Daubizit, M.

1993-01-01

The invention concerns a process of quantity determination of uranium by chromatography in liquid zone, usable to determine the quantity of uranium traces. Solutions to be treated can be aqueous or organic

Protection of groundwater resources quality and quantity in mining areas

International Nuclear Information System (INIS)

Grmela, A.

1997-01-01

This contribution is devoted to the problems of the impact of land subsidence from coal and other mining systems on underground and surface waters, particularly in relation to the possible influence on quality and quantity of pumped waters for public or individual supply. It determines features of permanent and time-limited changes of hydrogeological structure and effectiveness of measures for their minimization (classification of sources from the point of view of protection, delineation of protection zones for water resources, monitoring of effectiveness of measures). Case studies are presented for examples from the Czech part of Upper Silesian Basin - catchment area Doubrava-Spluchov, Karvina-Stare Mesto, Ostrava-Nove Ves, and Dubi, Darkov Spa. Attention is focused on problems of delimitation of protection zones in undermined areas in respect to the new proposal of the Appendix to Water Law. 8 refs., 2 figs

Impact of the Velo 2 half misalignment on physical quantities

CERN Document Server

Roguljic, Matej; Borghi, Silvia; Grillo, Lucia; CERN. Geneva. EP Department

2016-01-01

The impact of the misalignment of the Vertex Locator of the LHCb experiment on the physical quantities of the decay "$D^{*+} \\rightarrow (D^{0}\\rightarrow K^{-}\\pi^{+}) \\pi^{+} $" is studied in this note. Different misalignments of the 2 halves are applied to Monte Carlo data and the variations of the physical quantities with respect to the case without misalignment are evaluated. The results show the importance of the VELO 2 half alignment which can significantly affect the physics performance in the large misalignment case. A misalignment equal to the precision of the real-time alignment of the Vertex Locator is found to have a negligible effect on the studied physical quantities.

Quality or quantity? Exploring the relationship between Public Open Space attributes and mental health in Perth, Western Australia.

Science.gov (United States)

Francis, Jacinta; Wood, Lisa J; Knuiman, Matthew; Giles-Corti, Billie

2012-05-01

Mental health is a public health priority globally. Public Open Space (POS) may enhance mental health by facilitating contact with nature and the development of supportive relationships. Despite growing interest in the influence of the built environment on mental health, associations between POS attributes and mental health remain relatively unexplored. In particular, few studies have examined the relative effects of the quantity and quality of POS within a neighbourhood on mental health. Guided by a social-ecological framework, this study investigated the relationship between POS attributes (i.e., quantity and quality) and better mental health (i.e., low risk of psychological distress) in residents of new housing developments in the Perth metropolitan area, Western Australia. The extent to which relationships between POS attributes and mental health were confounded by psychosocial factors (e.g., social support, sense of community) and frequent use of POS was also explored. Data were obtained from a cross-sectional survey (n = 911), a POS audit, and Geographical Information Systems, and was analysed using logistic regression. Approximately 80% of survey participants were at low risk of psychological distress. Residents of neighbourhoods with high quality POS had higher odds of low psychosocial distress than residents of neighbourhoods with low quality POS. This appeared to be irrespective of whether or not they used POS. However, the quantity of neighbourhood POS was not associated with low psychological distress. From a mental health perspective, POS quality within a neighbourhood appears to be more important than POS quantity. This finding has policy implications and warrants further investigation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Association between work-family conflict and smoking quantity among daily smokers.

Science.gov (United States)

Macy, Jonathan T; Chassin, Laurie; Presson, Clark C

2013-11-01

Recent work demonstrated a direct relation between work-family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work-family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors.

Quantities of natural gas transported in January-December 2009

International Nuclear Information System (INIS)

2010-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2009: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

Amount of Televised Alcohol Advertising Exposure and the Quantity of Alcohol Consumed by Youth.

Science.gov (United States)

Naimi, Timothy S; Ross, Craig S; Siegel, Michael B; DeJong, William; Jernigan, David H

2016-09-01

Although studies demonstrate that exposure to brand-specific alcohol advertising is associated with an increased likelihood of youth consuming particular brands, the relationship between quantity of brand-specific advertising exposure and quantity of brand-specific consumption has not been firmly established. Using the Alcohol Brand Research Among Underage Drinkers (ABRAND) national sample of 1,031 young drinkers (ages 13-20), this study examined the relationship between their aggregated past-year exposure to advertising (in adstock units, a measure based on gross rating points) for 61 alcohol brands that advertised on the 20 most popular nonsports television programs viewed by underage youth and their aggregated total consumption of those same brands during the past 30 days. Predictive models adjusted for other media exposure, predictors of youth's alcohol consumption, and the consumption of brands not advertised on the 20 shows. For the fully adjusted models, each 100 adstock unit increase in exposure (about 1 SD) was associated with an increase of 5.9 drinks (95% CI [0.9, 11.0 drinks]) consumed during the past 30 days among those with less than 300 units of advertising exposure, and an increase of 55.7 drinks (95% CI [13.9, 97.4 drinks]) among those with 300 or more adstock units of exposure. Among underage youth, the quantity of brand-specific advertising exposure is positively associated with the total quantity of consumption of those advertised brands, even after controlling for the consumption of non-advertised brands. Future research should examine exposure-consumption relationships longitudinally and in other media.

Amount of Televised Alcohol Advertising Exposure and the Quantity of Alcohol Consumed by Youth

Science.gov (United States)

Naimi, Timothy S.; Ross, Craig S.; Siegel, Michael B.; DeJong, William; Jernigan, David H.

2016-01-01

Objective: Although studies demonstrate that exposure to brand-specific alcohol advertising is associated with an increased likelihood of youth consuming particular brands, the relationship between quantity of brand-specific advertising exposure and quantity of brand-specific consumption has not been firmly established. Method: Using the Alcohol Brand Research Among Underage Drinkers (ABRAND) national sample of 1,031 young drinkers (ages 13–20), this study examined the relationship between their aggregated past-year exposure to advertising (in adstock units, a measure based on gross rating points) for 61 alcohol brands that advertised on the 20 most popular nonsports television programs viewed by underage youth and their aggregated total consumption of those same brands during the past 30 days. Predictive models adjusted for other media exposure, predictors of youth’s alcohol consumption, and the consumption of brands not advertised on the 20 shows. Results: For the fully adjusted models, each 100 adstock unit increase in exposure (about 1 SD) was associated with an increase of 5.9 drinks (95% CI [0.9, 11.0 drinks]) consumed during the past 30 days among those with less than 300 units of advertising exposure, and an increase of 55.7 drinks (95% CI [13.9, 97.4 drinks]) among those with 300 or more adstock units of exposure. Conclusions: Among underage youth, the quantity of brand-specific advertising exposure is positively associated with the total quantity of consumption of those advertised brands, even after controlling for the consumption of non-advertised brands. Future research should examine exposure–consumption relationships longitudinally and in other media. PMID:27588530

48 CFR 852.270-2 - Bread and bakery products-quantities.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Bread and bakery products... Bread and bakery products—quantities. As prescribed in 870.111-3, insert the following clause: Bread and Bakery Products—Quantities (JAN 2008) The bidder agrees to furnish up to 25 percent more or 25 percent...

Terms and definitions in the field of radiological technique. Dose quantities and units. Begriffe und Benennungen in der radiologischen Technik. Dosisgroessen und Dosiseinheiten

Energy Technology Data Exchange (ETDEWEB)

1985-01-01

The standard gives the terms and definitions of concepts, dose quantities and units. The radiation field condition 'secondary electron equilibrium', which forms part of the definition of standard ion dose, is given more precisely. The term 'free in air' is used in its original meaning, i.e. characterization of measuring conditions excluding avoidable stray radiation, which deviates from DIN 6814, part 3/06.72. Dosemeters for measurement of standard ion dose of air kerma are calibrated 'free in air', but this calibration condition is not part of the quantity definition. The quantities standard ion dose or air kerma therefore can also be measured in any other material. The qunatitative relationships between standard ion dose and the quantities 'exposure' and air kerma, as given in the ICRU publication 33 'Quantities and Units' (1980), are explained. The standard introduces the SI units Gray (for energy dose), Sievert (for dose equivalent), and Becquerel (for the activity of a radioactive substance). As the change to the SI units conceals the approximated equality of the numerical values of the standrd ion dose of photon radiation in roentgen, of the energy dose for soft tissue in rad, and of the dose equivalent in rem, new definitions are given in accordance with ICRU 33 for the quantities specified dose rate, dose rate constant, and area exposure product. These definitions use the terms 'energy dose' and 'kerma'. The dose concepts applied in the field of radiation protection, especially ambient dose and individual dose, are defined as dose equivalents in compliance with the Radiation Protection Ordinance. The relevant sections present information on the conversion of standard ion dose values to the corresponding values of kerma, energy dose, or dose equivalent.

Experimental Study on Meso-Scale Milling Process Using Nanofluid Minimum Quantity Lubrication

International Nuclear Information System (INIS)

Lee, P. H.; Nam, T. S.; Li, Cheng Jun; Lee, S. W.

2010-01-01

This paper present the characteristics of micro- and meso-scale milling processes in which compressed cold air, minimum quantity lubrication (MQL) and MoS 2 nanofluid MQL are used. For process characterization, the micro and meso-scale milling experiments are conducted using desktop meso-scale machine tool system and the surface roughness is measured. The experimental results show that the use of compressed chilly air and nanofluid MQL in the micro- and meso-scale milling processes is effective in improving the surface finish

How tobacco companies have used package quantity for consumer targeting.

Science.gov (United States)

Persoskie, Alexander; Donaldson, Elisabeth A; Ryant, Chase

2018-05-31

Package quantity refers to the number of cigarettes or amount of other tobacco product in a package. Many countries restrict minimum cigarette package quantities to avoid low-cost packs that may lower barriers to youth smoking. We reviewed Truth Tobacco Industry Documents to understand tobacco companies' rationales for introducing new package quantities, including companies' expectations and research regarding how package quantity may influence consumer behaviour. A snowball sampling method (phase 1), a static search string (phase 2) and a follow-up snowball search (phase 3) identified 216 documents, mostly from the 1980s and 1990s, concerning cigarettes (200), roll-your-own tobacco (9), smokeless tobacco (6) and 'smokeless cigarettes' (1). Companies introduced small and large packages to motivate brand-switching and continued use among current users when faced with low market share or threats such as tax-induced price increases or competitors' use of price promotions. Companies developed and evaluated package quantities for specific brands and consumer segments. Large packages offered value-for-money and matched long-term, heavy users' consumption rates. Small packages were cheaper, matched consumption rates of newer and lighter users, and increased products' novelty, ease of carrying and perceived freshness. Some users also preferred small packages as a way to try to limit consumption or quit. Industry documents speculated about many potential effects of package quantity on appeal and use, depending on brand and consumer segment. The search was non-exhaustive, and we could not assess the quality of much of the research or other information on which the documents relied. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

A shared system of representation governing quantity discrimination in canids

Directory of Open Access Journals (Sweden)

Joseph M Baker

2012-10-01

Full Text Available One way to investigate the evolution of cognition is to compare the abilities of phylogenetically related species. The domestic dog (Canis lupus familiaris, for example, still shares cognitive abilities with the coyote (C. latrans. Both of these canids possess the ability to make psychophysical less/more discriminations of food based on quantity. Like many other species including humans, this ability is mediated by Weber’s Law: discrimination of continuous quantities is dependent on the ratio between the two quantities. As two simultaneously presented quantities of food become more similar, choice of the large or small option becomes random in both dogs and coyotes. It remains unknown, however, whether these closely related species within the same family—one domesticated, and one wild—make such quantitative comparisons with comparable accuracy. Has domestication honed or diminished this quantitative ability? Might different selective and ecological pressures facing coyotes drive them to be more or less able to accurately represent and discriminate food quantity than domesticated dogs? This study is an effort to elucidate this question concerning the evolution of non-verbal quantitative cognition.Here, we tested the quantitative discrimination ability of 16 domesticated dogs. Each animal was given 9 trials in which two different quantities of food were simultaneously displayed to them. The domesticated dogs’ performance on this task was then compared directly to the data from 16 coyotes’ performance on this same task reported by Baker and colleagues (2011.The quantitative discrimination abilities between the two species were strikingly similar. Domesticated dogs demonstrated similar quantitative sensitivity as coyotes, suggesting that domestication may not have significantly altered the psychophysical discrimination abilities of canids. Instead, this study provides further evidence for similar nonverbal quantitative abilities across

Variation in Quantity of Heat Produced from Charcoal of Prosopis ...

African Journals Online (AJOL)

Data were collected using the copper calorimeter, a thermometer, an air tight burner and a weight balance. The results showed a gradual decrease in the quantity of heat produced as combustion time increased from 10 40 minutes in all wood species. Significant differences (p<0.05) in the quantity of heat produced both ...

Moving beyond quantity of participation in process evaluation of an intervention to prevent excessive pregnancy weight gain

Directory of Open Access Journals (Sweden)

Paul Keriann H

2013-02-01

Full Text Available Abstract Background Few lifestyle interventions have successfully prevented excessive gestational weight gain. Understanding the program processes through which successful interventions achieve outcomes is important for the design of effective programs. The objective of this study was to evaluate the effect of the quantity and quality of participation in a healthy lifestyle intervention on risk of excessive gestational weight gain. Findings Pregnant women (N = 179 received five newsletters about weight, nutrition, and exercise plus postcards on which they were asked to set related goals and return to investigators. The quantity of participation (dose was defined as low for returning few or some vs. high for many postcards (N = 89, 49.7%. Quality of participation was low for setting few vs. high for some or many appropriate goals (N = 92, 51.4%. Fisher’s exact tests and multivariate logistic regression were used to analyze the effect of participation variables on the proportion with excessive weight gain. Quantity and quality of participation alone were each not significantly associated with excessive gestational weight gain, while quality of participation among those with high-levels of participation approached significance (p = 0.07. The odds of gaining excessively was decreased when women had both a high quantity and quality of participation (OR = 0.04, 95% CI = 0.005, 0.30. Conclusions Both quantity and quality of participation are important program process measures in evaluations of lifestyle interventions to promote healthy weight gain during pregnancy.

Multimodal semantic quantity representations: further evidence from Korean Sign Language

Directory of Open Access Journals (Sweden)

Frank eDomahs

2012-01-01

Full Text Available Korean deaf signers performed a number comparison task on pairs of Arabic digits. In their RT profiles, the expected magnitude effect was systematically modified by properties of number signs in Korean Sign Language in a culture-specific way (not observed in hearing and deaf Germans or hearing Chinese. We conclude that finger-based quantity representations are automatically activated even in simple tasks with symbolic input although this may be irrelevant and even detrimental for task performance. These finger-based numerical representations are accessed in addition to another, more basic quantity system which is evidenced by the magnitude effect. In sum, these results are inconsistent with models assuming only one single amodal representation of numerical quantity.

The effects of quantity and depth of processing on children's time perception.

Science.gov (United States)

Arlin, M

1986-08-01

Two experiments were conducted to investigate the effects of quantity and depth of processing on children's time perception. These experiments tested the appropriateness of two adult time-perception models (attentional and storage size) for younger ages. Children were given stimulus sets of equal time which varied by level of processing (deep/shallow) and quantity (list length). In the first experiment, 28 children in Grade 6 reproduced presentation times of various quantities of pictures under deep (living/nonliving categorization) or shallow (repeating label) conditions. Students also compared pairs of durations. In the second experiment, 128 children in Grades K, 2, 4, and 6 reproduced presentation times under similar conditions with three or six pictures and with deep or shallow processing requirements. Deep processing led to decreased estimation of time. Higher quantity led to increased estimation of time. Comparative judgments were influenced by quantity. The interaction between age and depth of processing was significant. Older children were more affected by depth differences than were younger children. Results were interpreted as supporting different aspects of each adult model as explanations of children's time perception. The processing effect supported the attentional model and the quantity effect supported the storage size model.

Testing quantity theory of money for the Turkish economy

OpenAIRE

Levent, Korap

2007-01-01

In this paper, it is tried to test the main assumptions of the Quantity Theory of Money for the Turkish economy. Using some contemporaneous estimation techniques to examine the long-run stationary economic relationships on which the quantity theory is constructed, it is found that stationary characteristics of the velocitities of narrowly and broadly defined monetary aggregates cannot be rejected. However, monetary aggregates seem to be endogenous for the long-run evoluation of prices and rea...

Association Between Work–Family Conflict and Smoking Quantity Among Daily Smokers

Science.gov (United States)

2013-01-01

Introduction: Recent work demonstrated a direct relation between work–family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work–family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Methods: Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Results: Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. Conclusions: After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors. PMID:23709611

Quantities of natural gas transported in August-December 2007

International Nuclear Information System (INIS)

2008-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the available monthly key figures of GRTgaz activity from August to December 2007: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

Radioenzymatic microassay for picogram quantities of serotonin or acetylserotonin in biological fluids and tissues

International Nuclear Information System (INIS)

Hussain, M.N.; Benedict, C.R.

1987-01-01

This paper describes several modifications of the original radioenzymatic assay for serotonin which increase the sensitivity of the assay 20-fold as well as enhance its reliability. Using this method serotonin concentrations can be directly measured in biological examples without precleaning the sample. When compared to currently available methods this assay is specific and sensitive to approximately 1 pg of serotonin and can be used to measure serotonin levels in individual brain nuclei or microliter quantities of biological fluids. This assay can be easily adapted for the direct measurement of N-acetylserotonin. A large number of samples can be assayed in a single working day

Determination of trace quantities of uranium in rocks mass spectrometric isotope dilution technique

International Nuclear Information System (INIS)

Kakazu, Mauricio Hiromitu

1980-01-01

A detailed experimental investigation on the thermionic emission of uranium deposited on a single flat type rhenium filament has been carried out. The study was aimed at determining the influence of various forms of deposition on the emission sensitivity and thermal stability of U + , UO + and UO 2 + ions. Based on these investigations, a technique, involving an addition of a small quantity of colloidal suspension of graphite on top of the uranyl nitrate sample deposited, was chosen because of its higher, emission sensitivity for uranium metal ions. The experimental parameters of the technique were optimised and the technique was employed in the determination of trace quantities of uranium in rock samples using mass spectrometric isotope dilution method. For the mass spectrometric isotope dilution analysis National Bureau of Standards uranium isotopic standard NBS-U 970 was employed as a tracer, where as the mass discrimination effect in the uranium isotope analysis was corrected using the uranium isotopic standard NBS-U500. Uranium was determined in each of the seven granite samples from Wyoming, USA and two USGS standard rocks. The precision of the analysis was found to be ±1% . The uranium values obtained on the rock samples were compared with the analyses of other investigators. Influence of the sample splitting on the uranium analysis was discussed in the light of the analytical results obtained.(author)

Symbols and definitions of quantities and units in isotope stoichiometry

International Nuclear Information System (INIS)

Junghans, P.; Krumbiegel, P.; Faust, H.

1982-01-01

On the basis of the International System of Units and recent recommendations of the IUPAC on 'Symbols and Terminology for Physicochemical Quantities and Units' a system is proposed of uniform and unambiguous symbols and definitions of quantities and units used in the isotope dilution technique. The close relationship between isotope stoichiometry and common stoichiometry is demonstrated. (author)

Consensus on items and quantities of clinical equipment required to deal with a mass casualties big bang incident: a national Delphi study.

Science.gov (United States)

Duncan, Edward A S; Colver, Keith; Dougall, Nadine; Swingler, Kevin; Stephenson, John; Abhyankar, Purva

2014-02-22

Major short-notice or sudden impact incidents, which result in a large number of casualties, are rare events. However health services must be prepared to respond to such events appropriately. In the United Kingdom (UK), a mass casualties incident is when the normal response of several National Health Service organizations to a major incident, has to be supported with extraordinary measures. Having the right type and quantity of clinical equipment is essential, but planning for such emergencies is challenging. To date, the equipment stored for such events has been selected on the basis of local clinical judgment and has evolved without an explicit evidence-base. This has resulted in considerable variations in the types and quantities of clinical equipment being stored in different locations. This study aimed to develop an expert consensus opinion of the essential items and minimum quantities of clinical equipment that is required to treat 100 people at the scene of a big bang mass casualties event. A three round modified Delphi study was conducted with 32 experts using a specifically developed web-based platform. Individuals were invited to participate if they had personal clinical experience of providing a pre-hospital emergency medical response to a mass casualties incident, or had responsibility in health emergency planning for mass casualties incidents and were in a position of authority within the sphere of emergency health planning. Each item's importance was measured on a 5-point Likert scale. The quantity of items required was measured numerically. Data were analyzed using nonparametric statistics. Experts achieved consensus on a total of 134 items (54%) on completion of the study. Experts did not reach consensus on 114 (46%) items. Median quantities and interquartile ranges of the items, and their recommended quantities were identified and are presented. This study is the first to produce an expert consensus on the items and quantities of clinical equipment

Varieties of Quantity Estimation in Children

Science.gov (United States)

Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

2015-01-01

In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3…

Analysis of step-up transformer tap change on the quantities at the point of connection to transmission grid

Directory of Open Access Journals (Sweden)

Đorđević Dragan

2017-01-01

Full Text Available The analysis of a step-up transformer tap change on the quantities at the point of connection to the transmission grid is presented in this paper. The point of connection of generator TENT A6 has been analyzed, and a detailed model of this generator is available in software package DIgSILENT Power Factory. The comparison between the effect of a step-up transformer tap change on the quantities at the point of connection during automatic and manual operation of voltage regulator has been conducted. In order to conduct the analysis of the manual operation of the voltage regulator, the comparison between the different methods of modeling of these modes has been performed. Several generator operating points, selected in order to represent the need for tap change, have been analyzed. Also, previously mentioned analyses have been performed taking into account the voltage-reactive stiffness at the point of connection.

Importance of frequency dependent magnetoresistance measurements in analysing the intrinsicality of magnetodielectric effect: A case study

Science.gov (United States)

Rai, Hari Mohan; Saxena, Shailendra K.; Mishra, Vikash; Kumar, Rajesh; Sagdeo, P. R.

2017-08-01

Magnetodielectric (MD) materials have attracted considerable attention due to their intriguing physics and potential future applications. However, the intrinsicality of the MD effect is always a major concern in such materials as the MD effect may arise also due to the MR (magnetoresistance) effect. In the present case study, we report an experimental approach to analyse and separate the intrinsic and MR dominated contributions of the MD phenomenon. For this purpose, polycrystalline samples of LaGa1-xAxO3 (A = Mn/Fe) have been prepared by solid state reaction method. The purity of their structural phase (orthorhombic) has been validated by refining the X-ray diffraction data. The RTMD (room temperature MD) response has been recorded over a frequency range of 20 Hz to 10 MHz. In order to analyse the intrinsicality of the MD effect, FDMR (frequency dependent MR) by means of IS (impedance spectroscopy) and dc MR measurements in four probe geometry have been carried out at RT. A significant RTMD effect has been observed in selected Mn/Fe doped LaGaO3 (LGO) compositions. The mechanism of MR free/intrinsic MD effect, observed in Mn/Fe doped LGO, has been understood speculatively in terms of modified cell volume associated with the reorientation/retransformation of spin-coupled Mn/Fe orbitals due to the application of magnetic field. The present analysis suggests that in order to justify the intrinsic/resistive origin of the MD phenomenon, FDMR measurements are more useful than measuring only dc MR or analysing the trends of magnetic field dependent change in the dielectric constant and tanδ. On the basis of the present case study, we propose that IS (FDMR) alone can be used as an effective experimental tool to detect and analyse the resistive and intrinsic parts contributing to the MD phenomenon.

40 CFR 273.8 - Applicability-household and conditionally exempt small quantity generator waste.

Science.gov (United States)

2010-07-01

... conditionally exempt small quantity generator waste. 273.8 Section 273.8 Protection of Environment ENVIRONMENTAL....8 Applicability—household and conditionally exempt small quantity generator waste. (a) Persons... universal wastes defined at § 273.9; and/or (2) Conditionally exempt small quantity generator wastes that...

Fundamental data analyses for measurement control

International Nuclear Information System (INIS)

Campbell, K.; Barlich, G.L.; Fazal, B.; Strittmatter, R.B.

1989-01-01

An important aspect of a complete measurement control program for special nuclear materials is the analysis of data from periodic control measurements of known standards. This chapter covers the following topics: basic algorithms including an introduction and terminology, the standard case (known mean and standard deviation), Shewart control charts, and sequential test for bias; modifications for nonstandard cases including modification for changing (decaying) standard value, modifications for deteriorating measurement precision, and modifications when repeated measurements are made; maintenance information including estimation of historical standard deviation (standard case), estimation of historical standard deviation (changing with time), normality and outliners, and other tests of randomness

Evaluation of specific absorption rate as a dosimetric quantity for electromagnetic fields bioeffects.

Directory of Open Access Journals (Sweden)

Dimitris J Panagopoulos

Full Text Available PURPOSE: To evaluate SAR as a dosimetric quantity for EMF bioeffects, and identify ways for increasing the precision in EMF dosimetry and bioactivity assessment. METHODS: We discuss the interaction of man-made electromagnetic waves with biological matter and calculate the energy transferred to a single free ion within a cell. We analyze the physics and biology of SAR and evaluate the methods of its estimation. We discuss the experimentally observed non-linearity between electromagnetic exposure and biological effect. RESULTS: WE FIND THAT: a The energy absorbed by living matter during exposure to environmentally accounted EMFs is normally well below the thermal level. b All existing methods for SAR estimation, especially those based upon tissue conductivity and internal electric field, have serious deficiencies. c The only method to estimate SAR without large error is by measuring temperature increases within biological tissue, which normally are negligible for environmental EMF intensities, and thus cannot be measured. CONCLUSIONS: SAR actually refers to thermal effects, while the vast majority of the recorded biological effects from man-made non-ionizing environmental radiation are non-thermal. Even if SAR could be accurately estimated for a whole tissue, organ, or body, the biological/health effect is determined by tiny amounts of energy/power absorbed by specific biomolecules, which cannot be calculated. Moreover, it depends upon field parameters not taken into account in SAR calculation. Thus, SAR should not be used as the primary dosimetric quantity, but used only as a complementary measure, always reporting the estimating method and the corresponding error. Radiation/field intensity along with additional physical parameters (such as frequency, modulation etc which can be directly and in any case more accurately measured on the surface of biological tissues, should constitute the primary measure for EMF exposures, in spite of similar

Evaluation of specific absorption rate as a dosimetric quantity for electromagnetic fields bioeffects.

Science.gov (United States)

Panagopoulos, Dimitris J; Johansson, Olle; Carlo, George L

2013-01-01

To evaluate SAR as a dosimetric quantity for EMF bioeffects, and identify ways for increasing the precision in EMF dosimetry and bioactivity assessment. We discuss the interaction of man-made electromagnetic waves with biological matter and calculate the energy transferred to a single free ion within a cell. We analyze the physics and biology of SAR and evaluate the methods of its estimation. We discuss the experimentally observed non-linearity between electromagnetic exposure and biological effect. WE FIND THAT: a) The energy absorbed by living matter during exposure to environmentally accounted EMFs is normally well below the thermal level. b) All existing methods for SAR estimation, especially those based upon tissue conductivity and internal electric field, have serious deficiencies. c) The only method to estimate SAR without large error is by measuring temperature increases within biological tissue, which normally are negligible for environmental EMF intensities, and thus cannot be measured. SAR actually refers to thermal effects, while the vast majority of the recorded biological effects from man-made non-ionizing environmental radiation are non-thermal. Even if SAR could be accurately estimated for a whole tissue, organ, or body, the biological/health effect is determined by tiny amounts of energy/power absorbed by specific biomolecules, which cannot be calculated. Moreover, it depends upon field parameters not taken into account in SAR calculation. Thus, SAR should not be used as the primary dosimetric quantity, but used only as a complementary measure, always reporting the estimating method and the corresponding error. Radiation/field intensity along with additional physical parameters (such as frequency, modulation etc) which can be directly and in any case more accurately measured on the surface of biological tissues, should constitute the primary measure for EMF exposures, in spite of similar uncertainty to predict the biological effect due to non-linearity.

The Implementation Internet of Things(IoT) Technology in Real Time Monitoring of Electrical Quantities

Science.gov (United States)

Despa, D.; Nama, G. F.; Muhammad, M. A.; Anwar, K.

2018-04-01

Electrical quantities such as Voltage, Current, Power, Power Factor, Energy, and Frequency in electrical power system tends to fluctuate, as a result of load changes, disturbances, or other abnormal states. The change-state in electrical quantities should be identify immediately, otherwise it can lead to serious problem for whole system. Therefore a necessity is required to determine the condition of electricity change-state quickly and appropriately in order to make effective decisions. Online monitoring of power distribution system based on Internet of Things (IoT) technology was deploy and implemented on Department of Mechanical Engineering University of Lampung (Unila), especially at three-phase main distribution panel H-building. The measurement system involve multiple sensors such current sensors and voltage sensors, while data processing conducted by Arduino, the measurement data stored in to the database server and shown in a real-time through a web-based application. This measurement system has several important features especially for realtime monitoring, robust data acquisition and logging, system reporting, so it will produce an important information that can be used for various purposes of future power analysis such estimation and planning. The result of this research shown that the condition of electrical power system at H-building performed unbalanced load, which often leads to drop-voltage condition

Memory for multiple cache locations and prey quantities in a food-hoarding songbird

Directory of Open Access Journals (Sweden)

Nicola eArmstrong

2012-12-01

Full Text Available Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes, a food hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with 1. the number of cache sites containing prey rewards and 2. the length of time separating cache creation and retrieval (retention interval. Results showed that subjects generally performed above chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3 and 4 cache sites from between 1, 10 and 60 seconds. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to one minute long retention intervals without training.

Under-reactor Room 305/2 of the unit 4 of Chernobyl 1 NPP: its state, fuel quantity evaluation

International Nuclear Information System (INIS)

Borovoj, A.A.; Lagunenko, A.S.; Pazukhin, Eh.M.

1997-01-01

The question of the quantity of the used up nuclear fuel in the under-reactor room is discussed. These are given the results of direct visual observation, TV-records and photographing in this room and their connection with the date of chemical analysis of core samples and dose rate measurement. On the basis of these results the detailed model of relative petitioning of the main elements in the volume space of the former active zone of the reactor is developed. The minimum quantity evaluation of nuclear fuel in the room 305/2 is given. 10 refs., 1 tab., 2 figs

Ground level measurement of nuclei from coal development in the northern Great Plains: baseline measurements. Final report

Energy Technology Data Exchange (ETDEWEB)

Davis, B. L.; Johnson, L. R.; Sengupta, S.; Yue, P. C.

1978-11-01

The Institute of Atmospheric Sciences of the South Dakota School of Mines and Technology has completed 20 months of ambient air sampling at rural and remote sites in a five-state region of the northern Great Plains. Sampling was accomplished by use of a 27-ft motor home laboratory containing living accommodations for a field crew of two. The laboratory was outfitted with a number of instruments for measurement of pollutant parameters: cloud condensation nuclei, ice nuclei, Aitken nuclei, size distribution information for Aitken size particulate, sulfur dioxide, ozone, raindrop size distributions, and pH of precipitation. In addition, an instrumented meteorological tower provided wind speed, wind direction, ambient air temperature, and dew-point temperature. Instruments varied as to durability and success of operation, but better than 90% data retrieval was possible for the entire 20-month sampling study. Analyses of the large quantities of data obtained were not possible under the initial baseline measurement program, but examination of most parameters indicate that the air masses in the northern Great Plains are still relatively clean and are influenced primarily by local sources of contamination rather than large regional sources. Particulate concentrations in these remote areas are representative of mountain stations or clean rural conditions, and sulfur dioxide concentrations are at the threshold of detectability of the instrument. Precipitation is only very slightly acidic, and no significant quantity of amorphous particles (such as coal dust or combustion products) is found in the quantitative analyses of the high-volume filter collections. A summary of ''average'' conditions observed over the study area is tabulated.

Third derivative thermodynamic quantities of aqueous tetrahydrofuran at 25 degrees C

DEFF Research Database (Denmark)

Westh, Peter; Yoshida, Koh; Inaba, Akira

2015-01-01

–THF interaction functions, HETHF–THF, and SETHF–THF. Using the literature density data, the effect of THF on the excess partial molar volume of THF, VETHF–THF, was also evaluated. Furthermore, we directly determined the partial molar entropy-volume cross fluctuation density of THF, View the MathML sourceδ......We measured the excess chemical potential, μΕTHF, the excess partial molar enthalpy and entropy of solute tetrahydrofuran (THF), HETHF and SETHF, in THF–H2O at 25 °C. Using these second derivatives of G, we graphically evaluated the third derivative quantities; the enthalpic, entropic THF...

Prices versus Quantities

DEFF Research Database (Denmark)

Hansen, Lars Gårn; Jensen, Frank

illustrate that this result does not generalise to a search fishery, where marginal costs are allowed to depend on harvest. Hansen et al (2008) study a fishery where non-compliance with regulations is a problem. When the regulator is uncertain about non-compliance (compliance uncertainty), then landing fees......Weitzman (2002) studies the regulation of a fishery characterised by constant marginal harvest costs and shows that price regulation performs better than quantity regulation when the regulator is uncertain about the biological reproduction function (ecological uncertainty). Here, we initially...... are the preferred type of regulation, and Hansen et al (2008) find that this result does generalise to a search fishery where marginal costs depend on harvest. In this paper, we simulate a stochastic stock-recruitment model for the Danish cod fishery in the Kategat capturing both ecological and compliance...

Allen's astrophysical quantities

CERN Document Server

2000-01-01

This new, fourth, edition of Allen's classic Astrophysical Quantities belongs on every astronomer's bookshelf. It has been thoroughly revised and brought up to date by a team of more than ninety internationally renowned astronomers and astrophysicists. While it follows the basic format of the original, this indispensable reference has grown to more than twice the size of the earlier editions to accommodate the great strides made in astronomy and astrophysics. It includes detailed tables of the most recent data on: - General constants and units - Atoms, molecules, and spectra - Observational astronomy at all wavelengths from radio to gamma-rays, and neutrinos - Planetary astronomy: Earth, planets and satellites, and solar system small bodies - The Sun, normal stars, and stars with special characteristics - Stellar populations - Cataclysmic and symbiotic variables, supernovae - Theoretical stellar evolution - Circumstellar and interstellar material - Star clusters, galaxies, quasars, and active galactic nuclei ...

Measurement of the analysing power of elastic proton-proton scattering at 582 MeV

International Nuclear Information System (INIS)

Berdoz, A.; Favier, B.; Foroughi, F.; Weddigen, C.

1984-01-01

The authors have measured the analysing power of elastic proton-proton scattering at 582 MeV for 14 angles from 20 to 80 0 CM. The angular range was limited to >20 0 by the energy loss of the recoil protons. The experiment was performed at the PM1 beam line at SIN. A beam intensity of about 10 8 particles s -1 was used. (Auth.)

The behavior, quantity, and location of undissolved gas in Tank 241-SY-101

Energy Technology Data Exchange (ETDEWEB)

Brewster, M.E.; Gallagher, N.B.; Hudson, J.D.; Stewart, C.W.

1995-10-01

Mitigation of episodic flammable gas releases from Hanford Waste Tank 241-SY-101 was accomplished in July 1993 with the installation of a mixer pump that prevents gas retention. But is has not been possible until recently to measure the effects of mixing on the waste or how much gas remains and where it is located. Direct measurements of the void fraction and rheology of the mixed waste by the void fraction instrument (VFI) and ball rheometer along with previous data provide estimates of the location, quantity, and behavior of undissolved gas in the tank. This report documents the compilation and integration of the information that enables this understanding.

Patterns in new dimensionless quantities containing melting temperature, and their dependence on pressure

Directory of Open Access Journals (Sweden)

U. WALZER

1980-06-01

Full Text Available The relationships existing between melting temperature and other
macroscopic physical quantities are investigated. A new dimensionless
quantity Q(1 not containing the Grtineisen parameter proves to be suited for serving in future studies as a tool for the determination of the melting temperature in the outer core of the Earth. The pressure dependence of more general dimensionless quantities Q„ is determined analytically and, for the chemical elements, numerically, too. The patterns of various interesting dimensionless quantities are shown in the Periodic Table and compared.

Reducing the default dispense quantity for new opioid analgesic prescriptions: study protocol for a cluster randomised controlled trial.

Science.gov (United States)

Bachhuber, Marcus A; Nash, Denis; Southern, William N; Heo, Moonseong; Berger, Matthew; Schepis, Mark; Cunningham, Chinazo O

2018-04-20

As opioid analgesic consumption has grown, so have opioid use disorder and opioid-related overdoses. Reducing the quantity of opioid analgesics prescribed for acute non-cancer pain can potentially reduce risks to the individual receiving the prescription and to others who might unintentionally or intentionally consume any leftover tablets. Reducing the default dispense quantity for new opioid analgesic prescriptions in the electronic health record (EHR) is a promising intervention to reduce prescribing. This study is a prospective cluster randomised controlled trial with two parallel arms. Primary care sites (n=32) and emergency departments (n=4) will be randomised in matched pairs to either a modification of the EHR so that new opioid analgesic prescriptions default to a dispense quantity of 10 tablets (intervention) or to no EHR change (control). The dispense quantity will remain fully modifiable by providers in both arms. From 6 months preintervention to 18 months postintervention, patient-level data will be analysed (ie, the patient is the unit of inference). Patient eligibility criteria are: (A) received a new opioid analgesic prescription, defined as no other opioid analgesic prescription in the prior 6 months; (B) age ≥18 years; and (C) no cancer diagnosis within 1 year prior to the new opioid analgesic prescription. The primary outcome will be the quantity of opioid analgesics prescribed in the initial prescription. Secondary outcomes will include opioid analgesic reorders and health service utilisation within 30 days after the initial prescription. Outcomes will be compared between study arms using a difference-in-differences analysis. This study has been approved by the Montefiore Medical Center/Albert Einstein College of Medicine Institutional Review Board with a waiver of informed consent (2016-6036) and is registered on ClinicalTrials.gov (NCT03003832, 6 December 2016). Findings will be disseminated through publication, conferences and meetings

A Bayesian approach to assess data from radionuclide activity analyses in environmental samples

International Nuclear Information System (INIS)

Barrera, Manuel; Lourdes Romero, M.; Nunez-Lagos, Rafael; Bernardo, Jose M.

2007-01-01

A Bayesian statistical approach is introduced to assess experimental data from the analyses of radionuclide activity concentration in environmental samples (low activities). A theoretical model has been developed that allows the use of known prior information about the value of the measurand (activity), together with the experimental value determined through the measurement. The model has been applied to data of the Inter-laboratory Proficiency Test organised periodically among Spanish environmental radioactivity laboratories that are producing the radiochemical results for the Spanish radioactive monitoring network. A global improvement of laboratories performance is produced when this prior information is taken into account. The prior information used in this methodology is an interval within which the activity is known to be contained, but it could be extended to any other experimental quantity with a different type of prior information available

IRE (Institut National des Radioelements) site in Belgium. Report of in situ measurements and analyses performed for the RTBF

International Nuclear Information System (INIS)

2010-05-01

This document reports various analyses performed within the frame of the preparation and filming of a TV documentary on the Belgium National Institute of Radio-elements. It reports gamma radiation measurements performed at the vicinity of the institute, discusses the possible origin of its increase at the vicinity of the institute, analyses of sludge samples coming from a wastewater treatment works, and analyses of milk, cabbage, mosses and sediments collected by residents

Estimation of the charge quantity from solar cell to battery; Taiyo denchi ni yoru chikudenchi eno juden yosoku

Energy Technology Data Exchange (ETDEWEB)

Tsutsumi, K; Nishitani, M [Daiichi University, College of Technology, Kagoshima (Japan)

1996-10-27

In performing an experiment of running a small electric vehicle by installing solar cells in it and by charging the storage battery at a specific voltage, an estimation was made on the charge quantity to the battery for each solar altitude and inclination of a module at different hours. The solar altitude was determined at Daiichi University, College of Technology, according to the month and the time of day from a formula using day-declination and time equation of a chronological table of science. The quantity of global solar radiation was determined by resolving the solar radiation into its direct and diffuse components on the basis of the extra-terrestrial solar radiation quantity with the change in radius vector taken into consideration; and then, the global solar radiation on the inclined face was obtained from the angle of inclination and incidence. On the roof of a Daiichi University building, solar cell modules were installed facing north and south at 0{degree}, 30{degree}, 45{degree}, 60{degree} and 90{degree} each, so that a short-circuit current was measured for each differently inclined angle. As a result of the experiment, shown in an regression formula is a relation between the temperature conversion value of the maximum output of the solar cell at the standard temperature of 25{degree}C and the quantity of solar radiation on the inclined surface. Consequently, it enabled the prediction of a charging quantity, in the case of running a small vehicle with solar cells installed, from the quantity of solar radiation on the inclined surface in the clear weather. 2 refs., 4 figs., 2 tabs.

Gluon Polarisation Measurements at COMPASS

CERN Document Server

Silva, Luís

2012-01-01

One of the missing keys in the present understanding of the spin structure of the nucleon is the contribution from the gluons: the so-called gluon polarisation. This quantity can be determined in DIS through the photon-gluon fusion process, in which two analysis methods may be used: (i) identifying open charm events or (ii) selecting events with high $p_{T}$ hadrons. The data used in the present work were collected in the COMPASS experiment, where a 160 GeV/c naturally polarised muon beam, impinging on a polarised nucleon fixed target is used. Preliminary results for the gluon polarisation from high $p_{T}$ and open charm analyses are presented. The gluon polarisation result for high $p_{T}$ hadrons is divided, for the first time, into three statistically independent measurements at LO. The result from open charm analysis is obtained at LO and NLO. In both analyses a new weighted method based on a neural network approach is used.

Birthday Cake Activity Structured Arrangement for Helping Children Determining Quantities

Directory of Open Access Journals (Sweden)

Neni Mariana

2010-07-01

Full Text Available Few researches have been concerned about relation between children’s spatial thinking and number sense. Narrowing for this small research, we focused on one component of spatial thinking, that is structuring objects, and one component of number senses, that is cardinality by determining quantities. This study focused on a design research that was conducted in Indonesia in which we investigated pre-school children’s (between 2 and 3.5 years old ability in making structured arrangement and their ability to determine the quantities by looking at the arrangements. The result shows us that some of the children were able to make such arrangement. However, the children found difficulties either to determine quantities from those arrangements or to compare some structures to easily recognize number of objects.

Determination of trace elements in atomic absorption spectrophotometry. Study of the atomic cloud and atom generator. Application to the measurement of physical quantities

International Nuclear Information System (INIS)

Hircq, Bernard.

1976-06-01

After the description of the absorption cell the principal parameters are studied: argon flow rate in the cell, atomization temperature, cell geometry etc. The technique is applied to the measurement of impurities in uranium after deposition on a carbon filament. The atomic concentration distribution and the dimensions of the cloud generated by a graphite filament are then studied along the axes parallel to the filament and as a function of the various experimental parameters. From the determination of the cloud elevation rate it is possible to calculate the absolute atomic concentration, which allows certain physical quantities to be evaluated: oscillator force, Lorentz Widening, diffusion coefficient... The size and penetration depth of the deposit are then determined with an ionic microprobe and the distribution with a Castaing microprobe. The chemical transformations undergone by the uranium matrix during the heat cycles are studied by the X-ray method [fr

Optimising neutron polarizers--measuring the flipping ratio and related quantities

CERN Document Server

Goossens, D J

2002-01-01

The continuing development of gaseous spin polarized sup 3 He transmission filters for use as neutron polarizers makes the choice of optimum thickness for these filters an important consideration. The 'quality factors' derived for the optimisation of transmission filters for particular measurements are general to all neutron polarizers. In this work optimisation conditions for neutron polarizers are derived and discussed for the family of studies related to measuring the flipping ratio from samples. The application of the optimisation conditions to sup 3 He transmission filters and other types of neutron polarizers is discussed. Absolute comparisons are made between the effectiveness of different types of polarizers for this sort of work.

Minimal Length, Measurability and Gravity

Directory of Open Access Journals (Sweden)

Alexander Shalyt-Margolin

2016-03-01

Full Text Available The present work is a continuation of the previous papers written by the author on the subject. In terms of the measurability (or measurable quantities notion introduced in a minimal length theory, first the consideration is given to a quantum theory in the momentum representation. The same terms are used to consider the Markov gravity model that here illustrates the general approach to studies of gravity in terms of measurable quantities.

[Relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii].

Science.gov (United States)

Zhu, Hua; Teng, Jianbei; Cai, Yi; Liang, Jie; Zhu, Yilin; Wei, Tao

2011-12-01

To find out the relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii. Microscopy-counting process was applied to starch quantity statistics, sulfuric acid-anthrone colorimetry was used to assay polysaccharides content and bromocresol green colorimetry was used to assay alkaloid content. Pearson product moment correlation analysis, Kendall's rank correlation analysis and Spearman's concordance coefficient analysis were applied to study their relativity. Extremely significant positive correlation was found between starch quantity and polysaccharides content, and significant negative correlation between alkaloid content and starch quantity was discovered, as well was between alkaloid content and polysaccharides content.

Non-Noether Conserved Quantity for Relativistic Nonholonomic System with Variable Mass

International Nuclear Information System (INIS)

Qiao Yongfen; Li Renjie; Ma Yongsheng

2005-01-01

Using form invariance under special infinitesimal transformations in which time is not variable, the non-Noether conserved quantity of the relativistic nonholonomic system with variable mass is studied. The differential equations of motion of the system are established. The definition and criterion of the form invariance of the system under infinitesimal transformations are studied. The necessary and sufficient condition under which the form invariance is a Lie symmetry is given. The condition under which the form invariance can be led to a non-Noether conserved quantity and the form of the conserved quantity are obtained. Finally, an example is given to illustrate the application of the result.

In-process hold-up as a measure of safeguards significance

International Nuclear Information System (INIS)

Hamlin, A.G.

1983-01-01

This paper examines the use of the in-process hold-up itself, as a measure of safeguards significance. It is argued that for any process plant it is possible to define design limits for in-process hold-up, outside which the plant will not operate, or will operate in a detectably abnormal manner. It follows, therefore, that if the in-process hold-up can be derived at frequent intervals by input/output analysis from the start of the campaign, the only diversion that can be made from it during that campaign is limited to the quantity necessary to move the apparent in-process hold-up from its normal operating condition to the upper limiting condition. It also follows that detection of this diversion is as positive for protracted diversion as for abrupt diversion. If that part of the in-process inventory that is only measurable by input/output analysis has an upper operating limit that differs from its normal operating limit by less than a significant safeguards quantity of the material in question, the IAEA's criteria for both quantity and timeliness can be met by a combination of input/output analysis to determine in-process hold-up during the campaign, together with a material balance over the campaign. The paper examines the possibility of applying this measure to process plants in general, discusses means of minimizing the in-process inventory that must be determined by input/output analysis, and the performance required of the input and output analysis. It concludes that with current precision of measurement and with one input and one output batch per day, each measured, the method would be satisfactory for a campaign lasting nearly a year and involving 6 tonnes of plutonium. The paper examines the considerable advantages in verification that would arise from limiting safeguards analyses to the two points of input and output. (author)

Estimation of measurement variances

International Nuclear Information System (INIS)

Anon.

1981-01-01

In the previous two sessions, it was assumed that the measurement error variances were known quantities when the variances of the safeguards indices were calculated. These known quantities are actually estimates based on historical data and on data generated by the measurement program. Session 34 discusses how measurement error parameters are estimated for different situations. The various error types are considered. The purpose of the session is to enable participants to: (1) estimate systematic error variances from standard data; (2) estimate random error variances from data as replicate measurement data; (3) perform a simple analysis of variances to characterize the measurement error structure when biases vary over time

Influence of clouds on earth climate. Modellings, measurements, and data analyses within the framework of an interconnected project; Einfluss von Wolken auf das Klima der Erde. Modellierungen, Messungen, Datenanalysen im Rahmen eines Verbundprojektes

Energy Technology Data Exchange (ETDEWEB)

Grassl, H; Raschke, E

1995-11-01

At the beginning of the project there was considerable uncertainty as to the influence of clouds of all kinds on the energy budget of the atmosphere, the quantities and impact of aerosols, and, especially, the physics of high curl clouds. There was neither a possibility to model such cloud systems, nor did reliable measuring methods exist. This interconnected project contributed to the solution of these problems with the aim to create a solid basis of work for future climate researches. Simultaneously, measurements were carried out, satellite data analysed, aerosol data by different authors compiled and evaluated, and numerical simulations of cloud sheets carried out. (orig.) [Deutsch] Zu Beginn des Vorhabens herrschten erhebliche Unsicherheiten ueber den Einfluss von Wolken aller Arten auf den Energiehaushalt der Atmosphaere, ueber die Mengen und Wirkungen des Aerosols - und insbesondere ueber die Physik der hohen Cirren. Es gab keine Modelliermoeglichkeiten fuer solche Wolkensysteme - noch existierten zuverlaessige Messmoeglichkeiten. Das Verbundvorhaben sollte zur Loesung dieser Probleme beitragen mit dem Ziel, eine solide Arbeitsbasis fuer zukuenftige Aufgaben der Klimaforschung zu schaffen. Es wurden gleichzeitig Messungen durchgefuehrt, Satellitendaten analysiert, Aerosoldaten unterschiedlicher Autoren zusammengetragen und geprueft sowie numerische Simulationen von Wolkenfeldern durchgefuehrt. (orig.)

Seasonal changes in food quantity and quality of the common North Sea copepods Temora longicornis and Pseudocalanus elongatus: a bioassay approach

DEFF Research Database (Denmark)

Koski, Marja; Dutz, Jörg; Klein Breteler, W.

2010-01-01

We evaluated the food quantity and quality over a seasonal cycle for the development and egg production of the common North Sea copepods Temora longicornis and Pseudocalanus elongatus, using a bioassay approach. Seston was sampled from December to October from a well-mixed water column of the Mar......We evaluated the food quantity and quality over a seasonal cycle for the development and egg production of the common North Sea copepods Temora longicornis and Pseudocalanus elongatus, using a bioassay approach. Seston was sampled from December to October from a well-mixed water column...... with the seston from the spring bloom in March-April. The juveniles of both species were able to complete their development only in spring experiments. A multiple regression analyses and comparison to a good-quality standard food of the same concentration suggested that, in an annual scale, the egg production...

BIRTHDAY CAKE ACTIVITY STRUCTURED ARRANGEMENT FOR HELPING CHILDREN DETERMINING QUANTITIES

Directory of Open Access Journals (Sweden)

Neni Mariana

2010-07-01

Full Text Available Few researches have been concerned about relation between children’s spatialthinking and number sense. Narrowing for this small research, we focused onone component of spatial thinking, that is structuring objects, and onecomponent of number senses, that is cardinality by determining quantities. Thisstudy focused on a design research that was conducted in Indonesia in which weinvestigated pre-school children’s (between 2 and 3.5 years old ability inmaking structured arrangement and their ability to determine the quantities bylooking at the arrangements. The result shows us that some of the children wereable to make such arrangement. However, the children found difficulties eitherto determine quantities from those arrangements or to compare some structuresto easily recognize number of objects.Keywords: structures, structured arrangement, cardinality DOI: http://dx.doi.org/10.22342/jme.1.1.790.53-70

Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports

Science.gov (United States)

2017-12-01

by the Army Acquisition Executive contains the following language . As a recently delegated Acquisition Category IC program, the AH-64E Apache...Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis, Project Leader Margaret L. Giles David M. Tate I...F E N S E A N A L Y S E S IDA Paper P-8490 Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis

Symmetries and conserved quantities in geodesic motion

International Nuclear Information System (INIS)

Hojman, S.; Nunez, L.; Patino, A.; Rago, H.

1986-01-01

Recently obtained results linking several constants of motion to one (non-Noetherian) symmetry to the problem of geodesic motion in Riemannian space-times are applied. The construction of conserved quantities in geodesic motion as well as the deduction of geometrical statements about Riemannian space-times are achieved

ADM pseudotensors, conserved quantities and covariant conservation laws in general relativity

International Nuclear Information System (INIS)

Fatibene, L.; Ferraris, M.; Francaviglia, M.; Lusanna, L.

2012-01-01

The ADM formalism is reviewed and techniques for decomposing generic components of metric, connection and curvature are obtained. These techniques will turn out to be enough to decompose not only Einstein equations but also covariant conservation laws. Then a number of independent sets of hypotheses that are sufficient (though not necessary) to obtain standard ADM quantities (and Hamiltonian) from covariant conservation laws are considered. This determines explicitly the range in which standard techniques are equivalent to covariant conserved quantities. The Schwarzschild metric in different coordinates is then considered, showing how the standard ADM quantities fail dramatically in non-Cartesian coordinates or even worse when asymptotically flatness is not manifest; while, in view of their covariance, covariant conservation laws give the correct result in all cases. - Highlights: ► In the paper ADM conserved quantities for GR are obtained from augmented conservation laws. ► Boundary conditions for this to be possible are considered and compared with the literature. ► Some different forms of Schwarzschild solutions are considered as simple examples of different boundary conditions.

A stochastic model for quantum measurement

International Nuclear Information System (INIS)

Budiyono, Agung

2013-01-01

We develop a statistical model of microscopic stochastic deviation from classical mechanics based on a stochastic process with a transition probability that is assumed to be given by an exponential distribution of infinitesimal stationary action. We apply the statistical model to stochastically modify a classical mechanical model for the measurement of physical quantities reproducing the prediction of quantum mechanics. The system+apparatus always has a definite configuration at all times, as in classical mechanics, fluctuating randomly following a continuous trajectory. On the other hand, the wavefunction and quantum mechanical Hermitian operator corresponding to the physical quantity arise formally as artificial mathematical constructs. During a single measurement, the wavefunction of the whole system+apparatus evolves according to a Schrödinger equation and the configuration of the apparatus acts as the pointer of the measurement so that there is no wavefunction collapse. We will also show that while the outcome of each single measurement event does not reveal the actual value of the physical quantity prior to measurement, its average in an ensemble of identical measurements is equal to the average of the actual value of the physical quantity prior to measurement over the distribution of the configuration of the system. (paper)

Studies on quantity and composition of dairy cow excreta

International Nuclear Information System (INIS)

Peschke, H.

1982-01-01

After feeding a lactating dairy cow a day ration completely enriched with 15 N, the quantities of feces and urine were registered over a period of ten days and put into proportion to the animal mass. The fecal dry matter was put into proportion to the dry matter of the fodder by means of 15 N analysis the N excretion with the excreta was determined concerning quantity and time. Selected feces and urine charges were used to produce a slurry model. The content of nutritive elements of the initial components and of the organic fertilizer are discussed. (author)

Uncertainty In Measuring Noise Parameters Of a Communication Receiver

International Nuclear Information System (INIS)

Korcz, Karol; Palczynska, Beata; Spiralski, Ludwik

2005-01-01

The paper presents the method of assessing uncertainty in measuring the usable sensitivity Es of communication receiver. The influence of partial uncertainties of measuring the noise factor F and the energy pass band of the receiver Δf on the combined standard uncertainty level is analyzed. The method to assess the uncertainty in measuring the noise factor on the basis of the systematic component of uncertainty, assuming that the main source of measurement uncertainty is the hardware of the measuring system, is proposed. The assessment of uncertainty in measuring the pass band of the receiver is determined with the assumption that input quantities of the measurement equation are not correlated. They are successive, discrete values of the spectral power density of the noise on the output of receiver. The results of the analyses of particular uncertainties components of measuring the sensitivity, which were carried out for a typical communication receiver, are presented

Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

Directory of Open Access Journals (Sweden)

Gaku Fukunaga

Full Text Available The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

Science.gov (United States)

Fukunaga, Gaku; Takayasu, Hideki; Takayasu, Misako

2016-01-01

The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

Non-destructive in situ measurement of radiological distributions in Hanford Site waste tanks

International Nuclear Information System (INIS)

Troyer, G.L.

1996-01-01

Measurement of radiological materials in defense nuclear waste stored in underground tanks at the Hanford Site is being used to indicate material distributions. Both safety assessment and future processing challenges are dependent on knowledge of the distribution kinds, and quantities of various key components. Data from CdTe and neutron detector measurements are shown and correlated with physical sampling and laboratory results. The multiple assay approach is shown to increase the confidence about the material distributions. As a result, costs of physical sampling and destructive analyses can be controlled while not severely limiting the uncertainty of results

New measurements in plutonium L X ray emission spectrum using an electron probe micro-analyser

International Nuclear Information System (INIS)

Bobin, J.L.; Despres, J.

1966-01-01

Further studies by means of an electron-probe micro-analyser, allowed report CEA-R--1798 authors to set up a larger plutonium X ray spectrum table. Measurements of plutonium L II and L III levels excitation potentials have also been achieved. Some remarks about apparatus performance data (such as spectrograph sensibility, resolving power and accuracy) will be found in the appendix. (authors) [fr

A small quantity of sodium arsenite will kill large cull hardwoods

Science.gov (United States)

Francis M. Rushmore

1956-01-01

Although it is well known that sodium arsenite is an effective silvicide, forestry literature contains little information about the minimum quantities of this chemical that are required to kill large cull trees. Such information would be of value because if small quantities of a chemical will produce satisfactory results, small holes or frills in the tree will hold it...

THE QUANTITY AND TURNOVER OF DEAD WOOD IN PERMANENT FOREST PLOTS IN SIX LIFE ZONES OF VENEZUELA

Science.gov (United States)

Dead wood can be an important component of the carbon pool in many forests, but few measurements have been made of this pool in tropical forests. To fill this gap, we determined the quantity of dead wood (downed and standing dead) in 25 long-term (up to 30 yr) permanent forest pl...

Terms and definitions in the field of radiological technique. Dose quantities and units. Draft. Begriffe und Benennungen in der radiologischen Technik. Dosisgroessen und Dosiseinheiten. Entwurf

Energy Technology Data Exchange (ETDEWEB)

1977-11-01

This draft standard contains the definitions of the terms, quantities, and units important in dosimetry, while the methods of measurement and calculation are dealt with in other standards. Other than the standard of June 1972, this revised draft standard introduces the SI units of the energy dose, the Gray, and of the activity of a radioactive substance, the Becquerel. Important new measuring quantities are the standard energy dose and the dose equivalent index. The terms local dose and personnel dose are redefined in agreement with the Radiation Protection Ordinance of October 13, 1976.

Terms and definitions in the field of radiological technique. Dose quantities and units. Draft. Begriffe und Benennungen in der radiologischen Technik. Dosisgroessen und Dosiseinheiten. Entwurf

Energy Technology Data Exchange (ETDEWEB)

1977-11-01

The standard contains the definitions of terms, quantities and units important in dosimetry, while other standards deal with the measurement and calculation methods. As against the June 1972 edition, this amended standard introduces the SI units of the energy dose, the Gray (Gy), and of the activity of a radioactive substance, the Becquerel (Bq). Important new measuring quantities are the standard energy dose and the equivalent dose index. The terms local dose and personnel dose are redefined in accordance with the Radiation Protection Ordinance of Oct. 13th, 1976.

Laser Beam Caustic Measurement with Focal Spot Analyser

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Gong, Hui; Bagger, Claus

2005-01-01

In industrial applications of high power CO2-lasers the caustic characteristics of the laser beam have great effects on the performance of the lasers. A welldefined high intense focused spot is essential for reliable production results. This paper presents a focal spot analyser that is developed...

Food quantity affects the sensitivity of Daphnia to road salt.

Science.gov (United States)

Brown, Arran H; Yan, Norman D

2015-04-07

Road deicing operations have raised chloride (Cl) levels in many temperate lakes in Europe and North America. These lakes vary widely in trophic status, but to date, no one has quantified the interaction between food quantity and road salt toxicity. We examined the effects of food quantity (particulate algal C concentration (C)) on the chronic toxicity of Cl to Daphnia in soft-water bioassays. There was a strong positive linear relationship (r(2) = 0.92 for NaCl and r(2) = 0.96 for CaCl2) between food quantity and Cl LC50. As food quantity increased from 0.2 to 1.0 mg C/L (levels characteristic of oligotrophic to eutrophic lakes, respectively), the chronic Cl LC50 increased from 55.7 to 284.8 mg Cl/L. Salt type (NaCl or CaCl2) did not affect the Cl LC50, Daphnia life history parameters, or the intrinsic rate of population increase (r). The life history parameter most sensitive to Cl was neonate production. Cl did not inhibit egg production, nor was the maternal lipid investment in eggs changed, but egg viability and the subsequent release of live neonates decreased as Cl levels increased and food decreased. Our results suggest the trophic status of lakes should be considered when assessing ecological threat from Cl.

Price effects of changing quantities supplied at the integrated european fish market

DEFF Research Database (Denmark)

Nielsen, Max; Smit, Jos; Guillen, Jordi

2012-01-01

to be −1.1. This implies that price flexibilities previously estimated for single European countries underestimate price changes at the European level caused by quantity changes. Results indicate that changing quantities can increase revenues from individual species with large own-price flexibilities...

Automated Decisional Model for Optimum Economic Order Quantity Determination Using Price Regressive Rates

Science.gov (United States)

Roşu, M. M.; Tarbă, C. I.; Neagu, C.

2016-11-01

The current models for inventory management are complementary, but together they offer a large pallet of elements for solving complex problems of companies when wanting to establish the optimum economic order quantity for unfinished products, row of materials, goods etc. The main objective of this paper is to elaborate an automated decisional model for the calculus of the economic order quantity taking into account the price regressive rates for the total order quantity. This model has two main objectives: first, to determine the periodicity when to be done the order n or the quantity order q; second, to determine the levels of stock: lighting control, security stock etc. In this way we can provide the answer to two fundamental questions: How much must be ordered? When to Order? In the current practice, the business relationships with its suppliers are based on regressive rates for price. This means that suppliers may grant discounts, from a certain level of quantities ordered. Thus, the unit price of the products is a variable which depends on the order size. So, the most important element for choosing the optimum for the economic order quantity is the total cost for ordering and this cost depends on the following elements: the medium price per units, the stock cost, the ordering cost etc.

Reliability of corneal dynamic scheimpflug analyser measurements in virgin and post-PRK eyes.

Science.gov (United States)

Chen, Xiangjun; Stojanovic, Aleksandar; Hua, Yanjun; Eidet, Jon Roger; Hu, Di; Wang, Jingting; Utheim, Tor Paaske

2014-01-01

To determine the measurement reliability of CorVis ST, a dynamic Scheimpflug analyser, in virgin and post-photorefractive keratectomy (PRK) eyes and compare the results between these two groups. Forty virgin eyes and 42 post-PRK eyes underwent CorVis ST measurements performed by two technicians. Repeatability was evaluated by comparing three consecutive measurements by technician A. Reproducibility was determined by comparing the first measurement by technician A with one performed by technician B. Intraobserver and interobserver intraclass correlation coefficients (ICCs) were calculated. Univariate analysis of covariance (ANCOVA) was used to compare measured parameters between virgin and post-PRK eyes. The intraocular pressure (IOP), central corneal thickness (CCT) and 1st applanation time demonstrated good intraobserver repeatability and interobserver reproducibility (ICC ≧ 0.90) in virgin and post-PRK eyes. The deformation amplitude showed a good or close to good repeatability and reproducibility in both groups (ICC ≧ 0.88). The CCT correlated positively with 1st applanation time (r = 0.437 and 0.483, respectively, pPRK eyes, virgin eyes showed longer 1st applanation time (7.29 ± 0.21 vs. 6.96 ± 0.17 ms, pPRK eyes. There were differences in 1st applanation time and deformation amplitude between virgin and post-PRK eyes, which may reflect corneal biomechanical changes occurring after the surgery in the latter.

Thermodynamic quantities for the Klein–Gordon equation

Indian Academy of Sciences (India)

We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverselinear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation.We use a method based on the Euler–MacLaurin formula to analytically compute thethermal ...

19 CFR 351.409 - Differences in quantities.

Science.gov (United States)

2010-04-01

... DUTIES Calculation of Export Price, Constructed Export Price, Fair Value, and Normal Value § 351.409... comparing export price or constructed export price with normal value, the Secretary will make a reasonable... section 773(a)(6)(C)(i) of the Act.) (b) Sales with quantity discounts in calculating normal value. The...

16 CFR 1.23 - Quantity limit rules.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Quantity limit rules. 1.23 Section 1.23 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE GENERAL... Robinson-Patman Act. These rules have the force and effect of law. [32 FR 8444, June 13, 1967. Redesignated...

7 CFR 1427.170 - Quantity for loan.

Science.gov (United States)

2010-01-01

... to the preservation or safety of the loan collateral. Loans may be made on a lower percentage basis... 7 Agriculture 10 2010-01-01 2010-01-01 false Quantity for loan. 1427.170 Section 1427.170... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COTTON Recourse Seed Cotton Loans § 1427.170...

Urgency of increasing the quantity and quality of student creativity program

Science.gov (United States)

Sarmini; Prasetya, Ketut; Nadiroh, Ulin

2018-01-01

Student creativity is very important to improve the quality and quantity. The purpose of this paper is to identify the quality and quantity of the Student Creativity Program. The method in this research is exploratory study. The subjects taken are the leaders of deans and vice deans at the State University of Surabaya. Data collection techniques used are kusioner. The result of this research is creativity program in student is very important. Not only improve the quality and quantity of creativity, but also affect the image of the institution. It is necessary to have written rules on the regulations on the Student Creativity Program and to take a comprehensive and comprehensive approach, and to organize the budget is the main thing.

Multidemand Multisource Order Quantity Allocation with Multiple Transportation Alternatives

Directory of Open Access Journals (Sweden)

Jun Gang

2015-01-01

Full Text Available This paper focuses on a multidemand multisource order quantity allocation problem with multiple transportation alternatives. To solve this problem, a bilevel multiobjective programming model under a mixed uncertain environment is proposed. Two levels of decision makers are considered in the model. On the upper level, the purchaser aims to allocate order quantity to multiple suppliers for each demand node with the consideration of three objectives: total purchase cost minimization, total delay risk minimization, and total defect risk minimization. On the lower level, each supplier attempts to optimize the transportation alternatives with total transportation and penalty costs minimization as the objective. In contrast to prior studies, considering the information asymmetry in the bilevel decision, random and fuzzy random variables are used to model uncertain parameters of the construction company and the suppliers. To solve the bilevel model, a solution method based on Kuhn-Tucker conditions, sectional genetic algorithm, and fuzzy random simulation is proposed. Finally, the applicability of the proposed model and algorithm is evaluated through a practical case from a large scale construction project. The results show that the proposed model and algorithm are efficient in dealing with practical order quantity allocation problems.

Measurement in Psychology: Conceptual Analysis and Synthesis Revisited

International Nuclear Information System (INIS)

Berglund, Birgitta

2013-01-01

The imagined existences of 'quantity' in psychology is a prerequisite for measurement. Any person (researcher or subject) may imagine homogeneous concepts as quantities, for example, (perceived) redness, loudness or heaviness of different kinds of objects or events. Conversely, heterogeneous concepts may be merged to imagined quantities such as intelligence or personality, which both are constructed from agreed upon sets of theoretical concepts. Measurement in physics, psychophysics and psychology will be contemplated, comparatively

Design and Analyses of High Aspect Ratio Nozzles for Distributed Propulsion Acoustic Measurements

Science.gov (United States)

Dippold, Vance F., III

2016-01-01

A series of three convergent round-to-rectangular high-aspect ratio nozzles were designed for acoustics measurements. The nozzles have exit area aspect ratios of 8:1, 12:1, and 16:1. With septa inserts, these nozzles will mimic an array of distributed propulsion system nozzles, as found on hybrid wing-body aircraft concepts. Analyses were performed for the three nozzle designs and showed that the flow through the nozzles was free of separated flow and shocks. The exit flow was mostly uniform with the exception of a pair of vortices at each span-wise end of the nozzle.

Radiation Protection Concepts and Quantities for the Occupational Exposure to Cosmic Radiation

International Nuclear Information System (INIS)

Bartlett, D.T.

1999-01-01

For the purposes of dose limitation and dose control, the harm, or detriment, of exposure to radiation is assessed by the quantity effective dose. Effective dose is evaluated by the application of factors to the averaged absorbed dose in the organs and tissues of the body. Radiation monitoring instruments are generally calibrated in terms of the quantity ambient dose equivalent which is defined in a simple spherical phantom. The relationship of these quantities is described. Requirements for the radiation protection of aircraft crew are given in the European Union Council Directive 96/29/EURATOM. There are requirements to assess the exposure of aircraft crew, to inform them of health risks, to reduce higher doses, and to control the dose to the foetus. There are no explicit dose limits, other than a dose objective to be applied to the exposure of the foetus, and no requirements for designation of areas or classification of workers. There are significant differences between the exposure condition of aircraft crew and workers in most other industries where there is occupational exposure to radiation. There are greater ranges of radiation types and energy, and there are different dose distributions and characteristics of the working populations. However, the field intensity is predictable and, with the exception of rare solar events, there is no risk of significant unexpected exposures. Dose assessment is anticipated to be by folding staff roster information with estimates of route doses, since there is little variability of dose rate within an aircraft. Route doses, which may be either an agreed average value for a given airport pairing and aircraft type, or be flight specific, will be closely linked to measured values. Requirements as to the accuracy of dose assessment should be applied which are broadly similar to those used in individual monitoring generally. (author)

Principles and foundation: national standards on quantities and units in nuclear science field

International Nuclear Information System (INIS)

Chen Lishu

1993-11-01

The main contents of National Standards on Quantities and units of atomic and nuclear physics (GB 3102.9) and Quantities and Units of nuclear reactions and ionizing radiations (GB 310.10) are presented in which most important quantities with their symbols and definitions in the nuclear scientific field are given. The principles and foundation, including the International System of Units (SI) and its application to the nuclear scientific field, in the setting of the National Standards are explained

Municipal water quantities and health in Nunavut households: an exploratory case study in Coral Harbour, Nunavut, Canada

Directory of Open Access Journals (Sweden)

Kiley Daley

2014-03-01

Full Text Available Background: Access to adequate quantities of water has a protective effect on human health and well-being. Despite this, public health research and interventions are frequently focused solely on water quality, and international standards for domestic water supply minimums are often overlooked or unspecified. This trend is evident in Inuit and other Arctic communities even though numerous transmissible diseases and bacterium infections associated with inadequate domestic water quantities are prevalent. Objectives: Our objective was to explore the pathways by which the trucked water distribution systems being used in remote northern communities are impacting health at the household level, with consideration given to the underlying social and environmental determinants shaping health in the region. Methods: Using a qualitative case study design, we conducted 37 interviews (28 residents, 9 key informants and a review of government water documents to investigate water usage practices and perspectives. These data were thematically analysed to understand potential health risks in Arctic communities and households. Results: Each resident receives an average of 110 litres of municipal water per day. Fifteen of 28 households reported experiencing water shortages at least once per month. Of those 15, most were larger households (5 people or more with standard sized water storage tanks. Water shortages and service interruptions limit the ability of some households to adhere to public health advice. The households most resilient, or able to cope with domestic water supply shortages, were those capable of retrieving their own drinking water directly from lake and river sources. Residents with extended family and neighbours, whom they can rely on during shortages, were also less vulnerable to municipal water delays. Conclusions: The relatively low in-home water quantities observed in Coral Harbour, Nunavut, appear adequate for some families. Those living in

[Application of target restoration space quantity and quantitative relation in precise esthetic prosthodontics].

Science.gov (United States)

Haiyang, Yu; Tian, Luo

2016-06-01

Target restoration space (TRS) is the most precise space required for designing optimal prosthesis. TRS consists of an internal or external tooth space to confirm the esthetics and function of the final restoration. Therefore, assisted with quantitive analysis transfer, TRS quantitative analysis is a significant improvement for minimum tooth preparation. This article presents TRS quantity-related measurement, analysis, transfer, and internal relevance of three TR. classifications. Results reveal the close bond between precision and minimally invasive treatment. This study can be used to improve the comprehension and execution of precise esthetic prosthodontics.

Locomotor activity measures in the diagnosis of Attention Deficit Hyperactivity Disorder: Meta-analyses and new findings

Science.gov (United States)

Murillo, Lourdes García; Cortese, Samuele; Anderson, David; Martino, Adriana Di; Castellanos, Francisco Xavier

2015-01-01

Introduction Our aim was to assess differences in movement measures in Attention-Deficit/Hyperactivity Disorder (ADHD) vs. typically developing (TD) controls. Methods We performed meta-analyses of published studies on motion measures contrasting ADHD with controls. We also conducted a case-control study with children/adolescents (n=61 TD, n=62 ADHD) and adults (n=30 TD, n=19 ADHD) using the McLean Motion Activity Test, semi-structured diagnostic interviews and the Behavior Rating Inventory of Executive Function and Conners (Parent, Teacher; Self) Rating Scales. Results Meta-analyses revealed medium-to-large effect sizes for actigraph (standardized mean difference [SMD]: 0.64, 95% Confidence interval (CI): 0.43, 0.85) and motion tracking systems (SDM: 0.92, 95% CI: 0.65, 1.20) measures in differentiating individuals with ADHD from controls. Effects sizes were similar in studies of children/adolescents ([SMD]:0.75, 95% CI: 0.50, 1.01) and of adults ([SMD]: 0.73, 95% CI: 0.46, 1.00). In our sample, ADHD groups differed significantly in number of Head Movements (p=0.02 in children; p=0.002 in adults), Displacement (p=0.009/pADHD (d=0.45, 95% CI: 0.08, 0.82). In the concurrent go/no-go task, reaction time variability was significantly greater in ADHD (pADHD even in adults. Our results suggest that objective locomotion measures may be particularly useful in evaluating adults with possible ADHD. PMID:25770940

Psychological Measurement Needs Units, Ratios, and Real Quantities: A Commentary on Humphry

Science.gov (United States)

Kyngdon, Andrew

2011-01-01

Behavioral scientists have struggled with units of measurement for as long as they have struggled with measurement itself. Psychology's sole attempt at an explicit unit of measurement--the Lexile Framework for Reading (Stenner, Burdick, Sanford, & Burdick, 2006)--has been and continues to be ignored by the psychometric "cognoscenti."…

Precise and efficient evaluation of gravimetric quantities at arbitrarily scattered points in space

Science.gov (United States)

Ivanov, Kamen G.; Pavlis, Nikolaos K.; Petrushev, Pencho

2017-12-01

Gravimetric quantities are commonly represented in terms of high degree surface or solid spherical harmonics. After EGM2008, such expansions routinely extend to spherical harmonic degree 2190, which makes the computation of gravimetric quantities at a large number of arbitrarily scattered points in space using harmonic synthesis, a very computationally demanding process. We present here the development of an algorithm and its associated software for the efficient and precise evaluation of gravimetric quantities, represented in high degree solid spherical harmonics, at arbitrarily scattered points in the space exterior to the surface of the Earth. The new algorithm is based on representation of the quantities of interest in solid ellipsoidal harmonics and application of the tensor product trigonometric needlets. A FORTRAN implementation of this algorithm has been developed and extensively tested. The capabilities of the code are demonstrated using as examples the disturbing potential T, height anomaly ζ , gravity anomaly Δ g , gravity disturbance δ g , north-south deflection of the vertical ξ , east-west deflection of the vertical η , and the second radial derivative T_{rr} of the disturbing potential. After a pre-computational step that takes between 1 and 2 h per quantity, the current version of the software is capable of computing on a standard PC each of these quantities in the range from the surface of the Earth up to 544 km above that surface at speeds between 20,000 and 40,000 point evaluations per second, depending on the gravimetric quantity being evaluated, while the relative error does not exceed 10^{-6} and the memory (RAM) use is 9.3 GB.

Conserved quantities for stationary Einstein-Maxwell space-times

International Nuclear Information System (INIS)

Esposito, F.P.; Witten, L.

1978-01-01

It is shown that every stationary Einstein-Maxwell space-time has eight divergence-free vector fields and these are isolated in general form. The vector fields and associated conserved quantities are calculated for several families of space-times. (Auth.)

Variety more than quantity of fruit and vegetable intake varies by socioeconomic status and financial hardship. Findings from older adults in the EPIC cohort.

Science.gov (United States)

Conklin, Annalijn I; Forouhi, Nita G; Suhrcke, Marc; Surtees, Paul; Wareham, Nicholas J; Monsivais, Pablo

2014-12-01

Beyond quantity, variety of fruit and vegetable (FV) intake prevents chronic conditions and is widely recommended as critical to healthful eating. FV consumption is socially patterned, especially for women, but little is known about multiple economic determinants of variety or whether they differ from those of quantity. To examine socioeconomic status and financial hardships in relation to variety and quantity of FV intakes among older British women and men. Cross-sectional study of 9580 adults (50-79 years) in the nationally representative EPIC cohort who responded to a postal Health and Life Experiences Questionnaire (1996-2000) and Food Frequency Questionnaire (1998-2002). Variety counted unique items consumed (items/month) and quantity measured total intake (g/day). No consistent differences by any economic factor were observed for quantity of fruits or vegetables, except education in men. Lower education, lower social class and renting were independently associated with lower fruit variety and vegetable variety (p-trend consumption of diverse FV. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Unexpected seasonality in quantity and composition of Amazon rainforest air reactivity.

Science.gov (United States)

Nölscher, A C; Yañez-Serrano, A M; Wolff, S; de Araujo, A Carioca; Lavrič, J V; Kesselmeier, J; Williams, J

2016-01-22

The hydroxyl radical (OH) removes most atmospheric pollutants from air. The loss frequency of OH radicals due to the combined effect of all gas-phase OH reactive species is a measureable quantity termed total OH reactivity. Here we present total OH reactivity observations in pristine Amazon rainforest air, as a function of season, time-of-day and height (0-80 m). Total OH reactivity is low during wet (10 s(-1)) and high during dry season (62 s(-1)). Comparison to individually measured trace gases reveals strong variation in unaccounted for OH reactivity, from 5 to 15% missing in wet-season afternoons to mostly unknown (average 79%) during dry season. During dry-season afternoons isoprene, considered the dominant reagent with OH in rainforests, only accounts for ∼20% of the total OH reactivity. Vertical profiles of OH reactivity are shaped by biogenic emissions, photochemistry and turbulent mixing. The rainforest floor was identified as a significant but poorly characterized source of OH reactivity.

Manual of symbols and terminology for physicochemical quantities and units

CERN Document Server

Whiffen, D H

2013-01-01

Manual of Symbols and Terminology for Physicochemical Quantities and Units, 1979 Edition contains physical quantity tabulations of products. The Commission on Symbols, Terminology, and Units is a part of the Division of Physical Chemistry of the International Union of Pure and Applied Chemistry. Its general responsibilities are to secure clarity and precision, and wider agreement in the use of symbols, by chemists in different countries, among physicists, chemists, and engineers, and by editors of scientific journals. This book is composed of 13 chapters, and begins with the determination o

Units of measurement past, present and future international system of units

CERN Document Server

Gupta, S V

2010-01-01

It is for the first time that the subject of quantities and their respective units is dealt this much in detail a glimpse of units of measurements of base quantities of length, time, mass and volume is given for ancient India three and four dimensional systems of measurement units are critically examined establishment of the fact that only four base units are needed to describe a system of units the basics to arrive at the unit of a derived quantity are explained basic, derived and dimensionless quantities including quantity calculus are introduced life history of scientists concerned with measurements units are presented to be inspiring to working metrologists and students. The International System of Units including, Metre Convention Treaty and its various organs including International National of Weights and Measure are described. The realisation of base units is given in detail. Classes of derived units within the SI, units permitted for time to come, units outside SI but used in special fields of measur...

Critical experiments, measurements and analyses to establish a crack arrest methodology for nuclear pressure vessel steels. Task 62. Second annual progress report, 1 July 1975 to 30 June 1976

International Nuclear Information System (INIS)

Hahn, G.T.; Gehlen, P.C.; Hoagland, R.G.; Marschall, C.W.; Kanninen, M.F.; Popelar, C.; Rosenfield, A.R.

1976-10-01

Developments of the theory, the analyses and the materials characterization for assessments of crack arrest in heavy walled nuclear pressure vessels are described. A two-dimensional, dynamic, finite difference analysis of crack propagation and arrest, including inertia forces and thermal stresses is derived. The analysis is used to treat run-arrest events in DCB- and SEN-specimens. Calculations based on the one-dimensional analysis are compared with detailed measurements of run-arrest in two polymeric materials. The agreements between calculations and experiments support the dynamic, energy conservation theory of crack arrest. Implications of a K/sub ID/-crack velocity curve with a negative slope are examined. The quantity K/sub Im/, the minimum propagating crack toughness, is identified as the crack arrest material property for engineering applications. Considerations entering the design of a crack arrest property measuring procedure, including specimen shape, size, thickness and the crack jump are discussed. The influence of side grooves on the propensity for crack branching is examined. Compliance measurements for rectangular DCB-specimens are presented and analyzed. Energy losses arising from damping remote from the crack tip in an A533B steel DCB specimen are described, and classed as negligible. Interactions between test pieces and the loading system are examined. A simplified procedure for measuring K/sub D/-, K/sub m/-, and K/sub a/-values, based on the dynamic analysis of the crack length at arrest is demonstrated. Measurements of K/sub D/ at temperatures in the range (NDT-66)C to (NDT +34)C and for crack velocities in the range 200 ms -1 to 1000 ms -1 are presented. The connection between propagating crack toughness values and the rapidly loaded stationary crack toughness K/sub Id/ is examined

A miniaturised, nested-cylindrical electrostatic analyser geometry for dual electron and ion, multi-energy measurements

Energy Technology Data Exchange (ETDEWEB)

Bedington, Robert, E-mail: r.bedington@nus.edu.sg; Kataria, Dhiren; Smith, Alan

2015-09-01

The CATS (Cylindrical And Tiny Spectrometer) electrostatic optics geometry features multiple nested cylindrical analysers to simultaneously measure multiple energies of electron and multiple energies of ion in a configuration that is targeted at miniaturisation and MEMS fabrication. In the prototyped model, two configurations of cylindrical analyser were used, featuring terminating side-plates that caused particle trajectories to either converge (C type) or diverge (D type) in the axial direction. Simulations show how these different electrode configurations affect the particle focussing and instrument parameters; C-type providing greater throughputs but D-type providing higher resolving powers. The simulations were additionally used to investigate unexpected plate spacing variations in the as-built model, revealing that the k-factors are most sensitive to the width of the inter-electrode spacing at its narrowest point. - Highlights: • A new nested cylindrical miniaturised electrostatic analyser geometry is described. • “Converging” (C) and “diverging” (D) type channel properties are investigated. • C channels are shown to have greater throughputs and D greater resolving powers. • Plate factors are shown to be sensitive to the minimum in inter-electrode spacing.

Simulation of the Impact of New Ocean Surface Wind Measurements on H*Wind Analyses

Science.gov (United States)

Miller, Timothy; Atlas, Robert; Black, Peter; Chen, Shuyi; Hood, Robbie; Johnson, James; Jones, Linwood; Ruf, Chris; Uhlhorn, Eric

2008-01-01

The H*Wind analysis, a product of the Hurricane Research Division of NOAA's Atlantic Oceanographic and Meteorological Laboratory, brings together wind measurements from a variety of observation platforms into an objective analysis of the distribution of surface wind speeds in a tropical cyclone. This product is designed to improve understanding of the extent and strength of the wind field, and to improve the assessment of hurricane intensity. See http://www.aoml.noaa.gov/hrd/data sub/wind.html. The Hurricane Imaging Radiometer (HIRAD) is a new passive microwave remote sensor for hurricane observations that is currently under development by NASA Marshall Space Flight Center, NOAA Hurricane Research Division, the University of Central Florida and the University of Michigan. HIRAD is being designed to enhance the current real-time airborne ocean surface winds observation capabilities of NOAA and USAF Weather Squadron hurricane hunter aircraft using the operational airbome Stepped Frequency Microwave Radiometer (SFMR). Unlike SFMR, which measures wind speed and rain rate along the ground track directly beneath the aircraft, HIRAD will provide images of the surface wind and rain field over a wide swath (approximately 3 x the aircraft altitude, or approximately 2 km from space). The instrument is described in a separate paper presented at this conference. The present paper describes a set of Observing System Simulation Experiments (OSSEs) in which measurements from the new instrument as well as those from existing instruments (air, surface, and space-based) are simulated from the output of a numerical model from the University of Miami, and those results are used to construct H*Wind analyses. Evaluations will be presented on the relative impact of HIRAD and other instruments on H*Wind analyses, including the use of HIRAD from 2 aircraft altitudes and from a space-based platform.

Friendship quantity and quality as predictors of rejection sensitivity in adolescents

Directory of Open Access Journals (Sweden)

Gabriela Šeboková

2014-12-01

Full Text Available The current study examines friendship quality and quantity as unique predictors of rejection sensitivity in adolescents. The purpose of the study was to analyze whether the unique contributions of friendship quality and quantity differ in adolescent boys and girls. Rejection sensitivity is conceptualized as the disposition to anxiously expect, readily perceive and intensively react to social rejection. That is why rejection sensitivity is considered to be a cognitive-affective mechanism which leads to increase of internalizing problems in children and adolescents (loneliness, social anxiety, depression.... Friendship variables have been found to predict the level of internalizing problems in adolescents. Little to no research, however, has examined friendship quality and quantity as predictors of level of rejection sensitivity. Participants in this study were 184 students (98 girls and 86 boys, aged from 13 to 16 (M=13.83, SD=1. Adolescents completed measures assessing number of their friends, quality of best friendship (self-report questionnaire Friendship qualities scale, Bukowski, Hoza, Boivin, 1994 and rejection sensitivity (self-report questionnaire Rejection sensitivity scale, Downey, Feldman, 1996. Regression analysis indicated that friendship features (companionship, balance, help, security, closeness, friendship quantity and overall friendship quality are significant unique predictors of sensitivity rejection in adolescents with. Results suggest that adolescents with higher number of and higher quality friendships have lower concerns about the possibility and expectation of rejection, which can lead to minimizing the risk of development of internalizing problems. However, only a small proportion of variance was accounted for in rejection sensitivity by the friendship variables (small to medium effect size. This suggests that different kind of peer relationships (peer acceptance, popularity, peer victimization make unique, differential

Effects of insemination quantity on honey bee queen physiology.

Directory of Open Access Journals (Sweden)

Freddie-Jeanne Richard

2007-10-01

Full Text Available Mating has profound effects on the physiology and behavior of female insects, and in honey bee (Apis mellifera queens, these changes are permanent. Queens mate with multiple males during a brief period in their early adult lives, and shortly thereafter they initiate egg-laying. Furthermore, the pheromone profiles of mated queens differ from those of virgins, and these pheromones regulate many different aspects of worker behavior and colony organization. While it is clear that mating causes dramatic changes in queens, it is unclear if mating number has more subtle effects on queen physiology or queen-worker interactions; indeed, the effect of multiple matings on female insect physiology has not been broadly addressed. Because it is not possible to control the natural mating behavior of queens, we used instrumental insemination and compared queens inseminated with semen from either a single drone (single-drone inseminated, or SDI or 10 drones (multi-drone inseminated, or MDI. We used observation hives to monitor attraction of workers to SDI or MDI queens in colonies, and cage studies to monitor the attraction of workers to virgin, SDI, and MDI queen mandibular gland extracts (the main source of queen pheromone. The chemical profiles of the mandibular glands of virgin, SDI, and MDI queens were characterized using GC-MS. Finally, we measured brain expression levels in SDI and MDI queens of a gene associated with phototaxis in worker honey bees (Amfor. Here, we demonstrate for the first time that insemination quantity significantly affects mandibular gland chemical profiles, queen-worker interactions, and brain gene expression. Further research will be necessary to elucidate the mechanistic bases for these effects: insemination volume, sperm and seminal protein quantity, and genetic diversity of the sperm may all be important factors contributing to this profound change in honey bee queen physiology, queen behavior, and social interactions in the

Symbolic Estrangement: Evidence against a Strong Association between Numerical Symbols and the Quantities They Represent

Science.gov (United States)

Lyons, Ian M.; Ansari, Daniel; Beilock, Sian L.

2012-01-01

Are numerals estranged from a sense of the actual quantities they represent? We demonstrate that, irrespective of numerical size or distance, direct comparison of the relative quantities represented by symbolic and nonsymbolic formats leads to performance markedly worse than when comparing 2 nonsymbolic quantities (Experiment 1). Experiment 2…

Understanding Measurement in Light of its Origins

Directory of Open Access Journals (Sweden)

Stephen eHumphry

2013-03-01

Full Text Available During the course of history, the natural sciences have seen the development of increasingly convenient short-hand symbolic devices for denoting physical quantities. These devices ultimately took the form of physical algebra. However, the convenience of algebra arguably came at a cost—a loss of the clarity of direct insights by Euclid, Galileo and Newton into natural quantitative relations. Physical algebra is frequently interpreted as ordinary algebra; i.e., it is interpreted as though symbols denote (a numbers and operations on numbers, as opposed to (b physical quantities and quantitative relations. The paper revisits the way in which Newton understood and expressed physical definitions and laws. Accordingly, it reviews a compact form of notation that has been used to denote both: (a ratios of physical quantities; and (b compound ratios, involving two or more kinds of quantity. The purpose is to show that it is consistent with historical developments to regard physical algebra as a device for denoting relations among ratios. Understood in the historical context, the objective of measurement is to establish that a physical quantity stands in a specific ratio to another quantity of the same kind. To clarify the meaning of measurement in terms of the historical origins of physics carries basic implications for the way in which measurement is understood and approached. Possible implications for the social sciences are considered.

Quantity assessment of waste in the dismantlement of liquid waste treatment plant and its actual state

International Nuclear Information System (INIS)

Uchiyama, Takafumi; Mitsuhashi, Ishi; Matsumoto, Tetsuo; Morishima, Kayoko; Tanzawa, Tomio

2016-01-01

From the progress of decommissioning project work of Tokyo City University Atomic Energy Research Institute, this paper reports the comparison between the actual amount of the waste generated during dismantlement work at liquid waste treatment facilities and the assessment quantity before starting the dismantlement. The quantity assessment was made on the basis of the installation license application, design specifications, drawings, records, history of use, site investigation results, etc. Since this quantity assessment did not take into account the dismantling contents of reservoir concrete, the assessed quantity of non-radioactive waste (NR waste) did not match the sum of actual NR waste. However, if an actually generated quantity of concrete of radioactive waste was added to the quantity assessment as NR waste, the quantity of actually generated NR waste and that of assessed NR waste were nearly consistent, which verified the validity of this assessment. This method is considered to be able to be utilized in the future quantity assessment of decommissioning work and the like. On the other hand, it was found that the number of drums that were actually stored tended to increase more than the estimated number of drum conversion. In old buildings, it is necessary to take into account the generation of waste other than radioactive materials in the quantity assessment stage and dismantlement stage. (A.O.)

Digital analyses of cartometric Fruska Gora guidelines

Directory of Open Access Journals (Sweden)

Živković Dragica

2013-01-01

Full Text Available Modern geo morphological topography research have been using quantity statistic and cartographic methods for topographic relief features, mutual relief features, mutual connection analyses on the grounds of good quality numeric parameters etc. Topographic features are important for topographic activities are important for important natural activities. Important morphological characteristics are precisely at the angle of topography, hypsometry, and topography exposition and so on. Small yet unknown relief slants can deeply affect land configuration, hypsometry, topographic exposition etc. Expositions modify the light and heat of interconnected phenomena: soil and air temperature, soil disintegration, the length of vegetation period, the complexity of photosynthesis, the fruitfulness of agricultural crops, the height of snow limit etc. [Projekat Ministarstva nauke Republike Srbije, br. 176008 i br. III44006

Threshold quantities for infectious diseases in periodic environments

NARCIS (Netherlands)

Heesterbeek, J.A.P.; Roberts, M.G.

1995-01-01

In this short note we give threshold quantities that determine the stability of the infection-free steady state for periodic deterministic systems that describe the spread of infectious diseases in populations whose individuals can be divided into a finite number of distinct groups. We concentrate

Evaluating the performance of commonly used gas analysers for methane eddy covariance flux measurements: the InGOS inter-comparison field experiment

Science.gov (United States)

Peltola, O.; Hensen, A.; Helfter, C.; Belelli Marchesini, L.; Bosveld, F. C.; van den Bulk, W. C. M.; Elbers, J. A.; Haapanala, S.; Holst, J.; Laurila, T.; Lindroth, A.; Nemitz, E.; Röckmann, T.; Vermeulen, A. T.; Mammarella, I.

2014-06-01

The performance of eight fast-response methane (CH4) gas analysers suitable for eddy covariance flux measurements were tested at a grassland site near the Cabauw tall tower (Netherlands) during June 2012. The instruments were positioned close to each other in order to minimise the effect of varying turbulent conditions. The moderate CH4 fluxes observed at the location, of the order of 25 nmol m-2 s-1, provided a suitable signal for testing the instruments' performance. Generally, all analysers tested were able to quantify the concentration fluctuations at the frequency range relevant for turbulent exchange and were able to deliver high-quality data. The tested cavity ringdown spectrometer (CRDS) instruments from Picarro, models G2311-f and G1301-f, were superior to other CH4 analysers with respect to instrumental noise. As an open-path instrument susceptible to the effects of rain, the LI-COR LI-7700 achieved lower data coverage and also required larger density corrections; however, the system is especially useful for remote sites that are restricted in power availability. In this study the open-path LI-7700 results were compromised due to a data acquisition problem in our data-logging setup. Some of the older closed-path analysers tested do not measure H2O concentrations alongside CH4 (i.e. FMA1 and DLT-100 by Los Gatos Research) and this complicates data processing since the required corrections for dilution and spectroscopic interactions have to be based on external information. To overcome this issue, we used H2O mole fractions measured by other gas analysers, adjusted them with different methods and then applied them to correct the CH4 fluxes. Following this procedure we estimated a bias of the order of 0.1 g (CH4) m-2 (8% of the measured mean flux) in the processed and corrected CH4 fluxes on a monthly scale due to missing H2O concentration measurements. Finally, cumulative CH4 fluxes over 14 days from three closed-path gas analysers, G2311-f (Picarro Inc

Reliability of corneal dynamic scheimpflug analyser measurements in virgin and post-PRK eyes.

Directory of Open Access Journals (Sweden)

Xiangjun Chen

Full Text Available PURPOSE: To determine the measurement reliability of CorVis ST, a dynamic Scheimpflug analyser, in virgin and post-photorefractive keratectomy (PRK eyes and compare the results between these two groups. METHODS: Forty virgin eyes and 42 post-PRK eyes underwent CorVis ST measurements performed by two technicians. Repeatability was evaluated by comparing three consecutive measurements by technician A. Reproducibility was determined by comparing the first measurement by technician A with one performed by technician B. Intraobserver and interobserver intraclass correlation coefficients (ICCs were calculated. Univariate analysis of covariance (ANCOVA was used to compare measured parameters between virgin and post-PRK eyes. RESULTS: The intraocular pressure (IOP, central corneal thickness (CCT and 1st applanation time demonstrated good intraobserver repeatability and interobserver reproducibility (ICC ≧ 0.90 in virgin and post-PRK eyes. The deformation amplitude showed a good or close to good repeatability and reproducibility in both groups (ICC ≧ 0.88. The CCT correlated positively with 1st applanation time (r = 0.437 and 0.483, respectively, p<0.05 and negatively with deformation amplitude (r = -0.384 and -0.375, respectively, p<0.05 in both groups. Compared to post-PRK eyes, virgin eyes showed longer 1st applanation time (7.29 ± 0.21 vs. 6.96 ± 0.17 ms, p<0.05 and lower deformation amplitude (1.06 ± 0.07 vs. 1.17 ± 0.08 mm, p < 0.05. CONCLUSIONS: CorVis ST demonstrated reliable measurements for CCT, IOP, and 1st applanation time, as well as relatively reliable measurement for deformation amplitude in both virgin and post-PRK eyes. There were differences in 1st applanation time and deformation amplitude between virgin and post-PRK eyes, which may reflect corneal biomechanical changes occurring after the surgery in the latter.

Unified Symmetry and Conserved Quantities of Mechanical System in Phase Space

International Nuclear Information System (INIS)

Fang Jianhui; Ding Ning; Wang Peng

2006-01-01

In this paper, a new symmetry and its conserved quantities of a mechanical system in phase space are studied. The definition of this new symmetry, i.e., a unified one is presented, and the criterion of this symmetry is also given. The Noether, the generalized Hojman and the Mei conserved quantities of the unified symmetry of the system are obtained. The unified symmetry contains the Noether, the Lie and the Mei symmetries, and has more generalized significance.

A statistical model for measurement error that incorporates variation over time in the target measure, with application to nutritional epidemiology.

Science.gov (United States)

Freedman, Laurence S; Midthune, Douglas; Dodd, Kevin W; Carroll, Raymond J; Kipnis, Victor

2015-11-30

Most statistical methods that adjust analyses for measurement error assume that the target exposure T is a fixed quantity for each individual. However, in many applications, the value of T for an individual varies with time. We develop a model that accounts for such variation, describing the model within the framework of a meta-analysis of validation studies of dietary self-report instruments, where the reference instruments are biomarkers. We demonstrate that in this application, the estimates of the attenuation factor and correlation with true intake, key parameters quantifying the accuracy of the self-report instrument, are sometimes substantially modified under the time-varying exposure model compared with estimates obtained under a traditional fixed-exposure model. We conclude that accounting for the time element in measurement error problems is potentially important. Copyright © 2015 John Wiley & Sons, Ltd.

The Impact of the Support System’s Kinematic Structure on Selected Kinematic and Dynamic Quantities of an Experimental Crane

Directory of Open Access Journals (Sweden)

Trąbka Arkadiusz

2014-12-01

Full Text Available This paper presents a comparative analysis of two kinematic structures of the support system (with supports with bilateral and unilateral constraints, which were used in an experimental model of a crane. The computational model was developed by using the ADAMS software. The impact of the kinematic structure of the support system on selected kinematic and dynamic values that were recorded during the slewing motion was analysed. It was found, among other things, that an increased number of degrees of freedom of the support system leads to multiple distortions of time characteristics of kinematic and dynamic quantities.

Stable carbon isotope analyses of nanogram quantities of particulate organic carbon (pollen) with laser ablation nano combustion gas chromatography/isotope ratio mass spectrometry

NARCIS (Netherlands)

van Roij, Linda; Sluijs, Appy; Laks, Jelmer J.; Reichart, Gert-Jan

2017-01-01

Rationale: Analyses of stable carbon isotope ratios (δ13C values) of organic and inorganic matter remains have been instrumental for much of our understanding of present and past environmental and biological processes. Until recently, the analytical window of such analyses has been limited to

Effect of a multispecies probiotic supplement on quantity of irritable bowel syndrome-related intestinal microbial phylotypes

Directory of Open Access Journals (Sweden)

Lyra Anna

2010-09-01

Full Text Available Abstract Background Probiotics can alleviate the symptoms of irritable bowel syndrome (IBS, possibly by stabilizing the intestinal microbiota. Our aim was to determine whether IBS-associated bacterial alterations were reduced during multispecies probiotic intervention consisting of Lactobacillus rhamnosus GG, L. rhamnosus Lc705, Propionibacterium freudenreichii ssp. shermanii JS and Bifidobacterium breve Bb99. The intervention has previously been shown to successfully alleviate gastrointestinal symptoms of IBS. Methods The faecal microbiotas of 42 IBS subjects participating in a placebo-controlled double-blind multispecies probiotic intervention were analysed using quantitative real-time polymerase chain reaction (qPCR. Eight bacterial targets within the gastrointestinal microbiota with a putative IBS association were measured. Results A phylotype with 94% similarity to Ruminococcus torques remained abundant in the placebo group, but was decreased in the probiotic group during the intervention (P = 0.02 at 6 months. In addition, the clostridial phylotype, Clostridium thermosuccinogenes 85%, was stably elevated during the intervention (P = 0.00 and P = 0.02 at 3 and 6 months, respectively. The bacterial alterations detected were in accordance with previously discovered alleviation of symptoms. Conclusions The probiotic supplement was thus shown to exert specific alterations in the IBS-associated microbiota towards the bacterial 16S rDNA phylotype quantities described previously for subjects free of IBS. These changes may have value as non-invasive biomarkers in probiotic intervention studies.

A PQL (protein quantity loci) analysis of mature pea seed proteins identifies loci determining seed protein composition.

Science.gov (United States)

Bourgeois, Michael; Jacquin, Françoise; Cassecuelle, Florence; Savois, Vincent; Belghazi, Maya; Aubert, Grégoire; Quillien, Laurence; Huart, Myriam; Marget, Pascal; Burstin, Judith

2011-05-01

Legume seeds are a major source of dietary proteins for humans and animals. Deciphering the genetic control of their accumulation is thus of primary significance towards their improvement. At first, we analysed the genetic variability of the pea seed proteome of three genotypes over 3 years of cultivation. This revealed that seed protein composition variability was under predominant genetic control, with as much as 60% of the spots varying quantitatively among the three genotypes. Then, by combining proteomic and quantitative trait loci (QTL) mapping approaches, we uncovered the genetic architecture of seed proteome variability. Protein quantity loci (PQL) were searched for 525 spots detected on 2-D gels obtained for 157 recombinant inbred lines. Most protein quantity loci mapped in clusters, suggesting that the accumulation of the major storage protein families was under the control of a limited number of loci. While convicilin accumulation was mainly under the control of cis-regulatory regions, vicilins and legumins were controlled by both cis- and trans-regulatory regions. Some loci controlled both seed protein composition and protein content and a locus on LGIIa appears to be a major regulator of protein composition and of protein in vitro digestibility. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dangerous quantities of radioactive material (D-values)

International Nuclear Information System (INIS)

2010-01-01

Radioactive material is widely used in industry, medicine, education and agriculture. In addition, it occurs naturally. The health risk posed by these materials vary widely depending on many factors, the most important of which are the amount of the material involved and its physical and chemical form. Therefore, there is a need to identify the quantity and type of radioactive material for which emergency preparedness and other arrangements (e.g. security) are warrant due to the health risk they pose. The aim of this publication is to provide practical guidance for Member States on that quantity of radioactive material that may be considered dangerous. A dangerous quantity is that, which if uncontrolled, could be involved in a reasonable scenario resulting in the death of an exposed individual or a permanent injury, which decreases that person's quality of life. This publication is published as part of the IAEA Emergency Preparedness and Response Series. It supports several publications including: the IAEA Safety Requirements 'Preparedness and Response for a Nuclear or Radiological Emergency', IAEA Safety Standards Series No. GS-R-2. IAEA, Vienna (2002). IAEA Safety Guide 'Categorization of Radioactive Sources', IAEA Safety Standards Series No RS-G-1.9, IAEA, Vienna (2005) and IAEA Safety Guide 'Arrangements for Preparedness for a Nuclear or Radiological Emergency' IAEA Safety Standards Series No. GS-G-2.1, IAEA, Vienna (2006). The procedures and data in this publication have been prepared with due attention to accuracy. However, as part of the review process, they undergo ongoing quality assurance checks. Comments are welcome and, following a period that will allow for a more extensive review, the IAEA may revise this publication as part of the process of continuous improvement. The publication uses a number of exposure scenarios, risk models and dosimetric data, which could be used during the response to nuclear or radiological emergency or other purposes

Approximate Bayesian evaluations of measurement uncertainty

Science.gov (United States)

Possolo, Antonio; Bodnar, Olha

2018-04-01

The Guide to the Expression of Uncertainty in Measurement (GUM) includes formulas that produce an estimate of a scalar output quantity that is a function of several input quantities, and an approximate evaluation of the associated standard uncertainty. This contribution presents approximate, Bayesian counterparts of those formulas for the case where the output quantity is a parameter of the joint probability distribution of the input quantities, also taking into account any information about the value of the output quantity available prior to measurement expressed in the form of a probability distribution on the set of possible values for the measurand. The approximate Bayesian estimates and uncertainty evaluations that we present have a long history and illustrious pedigree, and provide sufficiently accurate approximations in many applications, yet are very easy to implement in practice. Differently from exact Bayesian estimates, which involve either (analytical or numerical) integrations, or Markov Chain Monte Carlo sampling, the approximations that we describe involve only numerical optimization and simple algebra. Therefore, they make Bayesian methods widely accessible to metrologists. We illustrate the application of the proposed techniques in several instances of measurement: isotopic ratio of silver in a commercial silver nitrate; odds of cryptosporidiosis in AIDS patients; height of a manometer column; mass fraction of chromium in a reference material; and potential-difference in a Zener voltage standard.

Whither the Nigerian Quantity Surveyors in the Information ...

African Journals Online (AJOL)

The paucity of information on the computing status of the quantity surveyors in Nigeria have been scanty and without empirical substantiation. The basic platform for entry to the information technology gateway is the acquisition, adoption and utilization of the computer. Baseline information is therefore indispensable for the ...

THE RELATION BETWEEN RESUDUE CHLOR QUANTITY AND WATER RELATED DISEASES IN AYDIN

Directory of Open Access Journals (Sweden)

Emine Didem EVCI

2006-02-01

Full Text Available Objectives: The correlation between the residue chlor quantity in water sampled in different points of Aydin province in 2004 and the incidence of infections via water (diarrhea, thyphoid fever, amoebic and bacillary dysentery is studied. Materials and Methods: A retrospective definitive study is performed during June-July 2005. Results: 924 physical and chemical analysis are performed in 2004. In winter season, the mean residue chlor was 0,57±0,10 mg/lt; there were 310 diarrhea cases and a bacillary dysentery case. In summer season, the mean residue chlor was 0,46±0,13 mg/lt; there were 529 diarrhea cases and an amoebic dysentery. Both seasons determined that there was a negative correlation between diarrhea and the residue chlor quantity and there was a poor connection between them and it was statistically unsignificant (for winter r= -0,242, p=0,224; for summer r= -0,148, p=0,480 Conclusion: However there is no determined, expressive connection between diarrhea cases and residue chlor quantity it was seen that as the residue chlor quantity evaluated, the diarrhea cases were reduced. [TAF Prev Med Bull 2006; 5(1.000: 1-7

Mining Waste Classification and Quantity of Non-Metal Minesin Slovenia

Directory of Open Access Journals (Sweden)

Ana Burger

2007-06-01

Full Text Available Mining is an important human activity that creates wealth and supplies materials for maintaining standard of living and further human development. However, mining has also negative impacts on the environment and society. One of them is the production of mining waste throughout the entire mining cycle, in particular in the mine development and operation /production stage.Due to the EU Directive 2006/21/EC on the management of waste from the extractive industries and its implementation in Member state, estimation on quality and quantity of mining waste from active non-metal mines in Slovenia was carried out. In the selected mines mining and processing was closely examined. With material flow analysis quantity and characteristics of mining waste were defined for several mines of different commodities.Data on mining waste were afterwards generalized in order to get an overall country evaluation on mining waste “production” of non-metal mines.Mining waste as a result of mining and beneficiation processes in non-metal mines of Slovenia is either inert or non-hazardous. Most of the mining waste is used for mine reclamation running simultaneously with the production phase. The largest amounts of mining waste per unit produced are created in dimension stone industry. Since the dimensionstone production is small, the waste amount is negligible. Large quantities of mining waste are produced in crushed stone and, sand and gravel operations, because aggregate production is pretty large with regard to other non-metals production in Slovenia. We can therefore conclude that large quantities of mining waste from non-metal mines, which are mostly used in reclamation and for side products, do not represent danger to the environment.

Quantity and quality limit detritivore growth: mechanisms revealed by ecological stoichiometry and co-limitation theory.

Science.gov (United States)

Halvorson, Halvor M; Sperfeld, Erik; Evans-White, Michelle A

2017-12-01

Resource quantity and quality are fundamental bottom-up constraints on consumers. Best understood in autotroph-based systems, co-occurrence of these constraints may be common but remains poorly studied in detrital-based systems. Here, we used a laboratory growth experiment to test limitation of the detritivorous caddisfly larvae Pycnopsyche lepida across a concurrent gradient of oak litter quantity (food supply) and quality (phosphorus : carbon [P:C ratios]). Growth increased simultaneously with quantity and quality, indicating co-limitation across the resource gradients. We merged approaches of ecological stoichiometry and co-limitation theory, showing how co-limitation reflected shifts in C and P acquisition throughout homeostatic regulation. Increased growth was best explained by elevated consumption rates and improved P assimilation, which both increased with elevated quantity and quality. Notably, C assimilation efficiencies remained unchanged and achieved maximum 18% at low quantity despite pronounced C limitation. Detrital C recalcitrance and substantive post-assimilatory C losses probably set a minimum quantity threshold to achieve positive C balance. Above this threshold, greater quality enhanced larval growth probably by improving P assimilation toward P-intensive growth. We suggest this interplay of C and P acquisition contributes to detritivore co-limitation, highlighting quantity and quality as potential simultaneous bottom-up controls in detrital-based ecosystems, including under anthropogenic change like nutrient enrichment. © 2017 by the Ecological Society of America.

Use of remote sensing, geographic information systems, and spatial statistics to assess spatio-temporal population dynamics of Heterodera glycines and soybean yield quantity and quality

Science.gov (United States)

Moreira, Antonio Jose De Araujo

Soybean, Glycine max (L.) Merr., is an important source of oil and protein worldwide, and soybean cyst nematode (SCN), Heterodera glycines, is among the most important yield-limiting factors in soybean production worldwide. Early detection of SCN is difficult because soybean plants infected by SCN often do not exhibit visible symptoms. It was hypothesized, however, that reflectance data obtained by remote sensing from soybean canopies may be used to detect plant stress caused by SCN infection. Moreover, reflectance measurements may be related to soybean growth and yield. Two field experiments were conducted from 2000 to 2002 to study the relationships among reflectance data, quantity and quality of soybean yield, and SCN population densities. The best relationships between reflectance and the quantity of soybean grain yield occurred when reflectance data were obtained late August to early September. Similarly, reflectance was best related to seed oil and seed protein content and seed size when measured during late August/early September. Grain quality-reflectance relationships varied spatially and temporally. Reflectance measured early or late in the season had the best relationships with SCN population densities measured at planting. Soil properties likely affected reflectance measurements obtained at the beginning of the season and somehow may have been related to SCN population densities at planting. Reflectance data obtained at the end of the growing season likely was affected by early senescence of SCN-infected soybeans. Spatio-temporal aspects of SCN population densities in both experiments were assessed using spatial statistics and regression analyses. In the 2000 and 2001 growing seasons, spring-to-fall changes in SCN population densities were best related to SCN population densities at planting for both experiments. However, within-season changes in SCN population densities were best related to SCN population densities at harvest for both experiments in

Measurement system to detect minute quantity of plutonium and other alpha emitter

International Nuclear Information System (INIS)

Simon, G.G.; Eyrich, W.

1990-01-01

Presently, the most highly developed method in use is the time correlation analysis method (TCA). With special equipped electronics and computer system designed for the TCA method, the time correlation of the registered events is used to determine the contribution of different multiplets. Thus, the efficiency of the measurement system and the isotopic composition of the probe can be determined and thereby the Plutonium content is calculated. In the case of minute contents of Plutonium, the TCA method is insufficient to calculate the efficiency of the measurement system because of the large statistical error relative to the fluctuation of the background counting rate. This paper reports that in addition to the TCA method, the local correlation analysis (LCA) was developed at the Nuclear Research Center in Karlsruhe (KfK) to yield more information. The efficiency of the measurement system can be calculated taking into account the lifetime of the neutrons in the measurement system and the probe position

Adaptation of the present concept of dosimetric radiation protection quantities for external radiation to radiation protection practice

International Nuclear Information System (INIS)

Boehm, J.; Thompson, I. M. G.

2004-01-01

The present concept of dosimetric radiation protection quantities for external radiation is reviewed. For everyday application of the concept some adaptations are recommended. The check of the compliance with dose limits should be performed either by the comparison with values of the respective operational quantities directly or by the calculation of the protection quantity by means of the operational quantity, the appertaining conversion coefficient and additional information of the radiation field. Only four operational quantities are regarded to be sufficient for most applications in radiation protection practice. The term equivalent should be used in the connection dose equivalent only. Proposals are made for names of frequently used operational quantities which are denoted up to now by symbols only. (authors)

By Default: The Effect of Prepopulated Prescription Quantities on Opioid Prescribing in the Emergency Department.

Science.gov (United States)

Santistevan, Jamie R; Sharp, Brian R; Hamedani, Azita G; Fruhan, Scott; Lee, Andrew W; Patterson, Brian W

2018-03-01

Opioid prescribing patterns have come under increasing scrutiny with the recent rise in opioid prescriptions, opioid misuse and abuse, and opioid-related adverse events. To date, there have been limited studies on the effect of default tablet quantities as part of emergency department (ED) electronic order entry. Our goal was to evaluate opioid prescribing patterns before and after the removal of a default quantity of 20 tablets from ED electronic order entry. We performed a retrospective observational study at a single academic, urban ED with 58,000 annual visits. We identified all adult patients (18 years or older) seen in the ED and discharged home with prescriptions for tablet forms of hydrocodone and oxycodone (including mixed formulations with acetaminophen). We compared the quantity of tablets prescribed per opioid prescription 12 months before and 10 months after the electronic order-entry prescription default quantity of 20 tablets was removed and replaced with no default quantity. No specific messaging was given to providers, to avoid influencing prescribing patterns. We used two-sample Wilcoxon rank-sum test, two-sample test of proportions, and Pearson's chi-squared tests where appropriate for statistical analysis. A total of 4,104 adult patients received discharge prescriptions for opioids in the pre-intervention period (151.6 prescriptions per 1,000 discharged adult patients), and 2,464 post-intervention (106.69 prescriptions per 1,000 discharged adult patients). The median quantity of opioid tablets prescribed decreased from 20 (interquartile ration [IQR] 10-20) to 15 (IQR 10-20) (pdefault quantity. While the most frequent quantity of tablets received in both groups was 20 tablets, the proportion of patients who received prescriptions on discharge that contained 20 tablets decreased from 0.5 (95% confidence interval [CI] [0.48-0.52]) to 0.23 (95% CI [0.21-0.24]) (pdefault quantity removal. Although the median number of tablets differed significantly

Quality or Quantity: A Statement for Teacher Training in Turkey

Directory of Open Access Journals (Sweden)

Ali AZAR

2011-01-01

Full Text Available Developed countries are initiating and implementing effective and appropriate technics in the field of teacher training. In Turkey, much research has been done in order to determine the qualification of teachers and, by this way, to train qualified teachers. Ministry of Education, Turkish Council of Higher Education, Faculties of Education and Faculties of Sciences have cooperated some certification systems, however, the research which is not supported by preliminary studies but exposured to political coercions lowered the quality of education. Besides, quantity is increased by pedagogical formation programs. In this study, Turkish teacher training system is analyzed with respect to quantity and quality.

Measurement of the quantity of water in organic solvents by infrared absorption an measurement of the dielectric constants; Dosage de l'eau dans les solvants organiques par absorption infra-rouge et mesure des constantes dielectriques

Energy Technology Data Exchange (ETDEWEB)

Desnoyer, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1959-06-15

Some chemical methods for the analysis of the quantity of water in solvents are first described, their object being the determination of the maximum error for cases where the water content is less than 1 per cent. - The first part of the work consists in describing infrared spectrometry as applied to the analysis of water in carbon tetrachloride, chloroform aniline, acetone and dioxane. A method based on isotopic exchange between heavy and light water is used on the one hand for determining the solubility of water in carbon tetrachloride and on the other hand for establishing standard solutions (sensitivity of the method). - In the second part the dielectric constant of water solvent solutions is measured. A table is presented giving the precision obtained by the two principal methods. These are comparable and further than that the appearance of the spectra suggests an interpretation of the anomalies observed in calibration curves obtained by the dielectric constant method. (author) [French] Quelques methodes chimiques d'analyses de l'eau dissoute dans les solvants sont decrites tout d'abord en vue de determiner l'erreur maxima dans le cas ou la teneur en eau ne depasse pas 1 pour cent. - Une premiere partie du travail expose la technique utilisee en spectrometrie infrarouge pour doser l'eau dans le tetrachlorure de carbone, chloroforme, aniline, acetone et le dioxane. Une methode basee sur l'echange isotopique entre l'eau legere et l'eau lourde permet de determiner d'une part la solubilite de l'eau dans le tetrachlorure de carbone et le chloroforme et d'autre part le titre en valeur absolue des solutions etalons (sensibilite de la methode). - Dans une deuxieme partie, on mesure la constante dielectrique des solutions eau-solvant. On dresse un tableau des precisions obtenues par les deux methodes principales. Celles-ci sont comparables et en outre, l'aspect du spectre suggere une interpretation des anomalies observees dans les courbes d'etalonnage tracees par la

Tuneable diode laser gas analyser for methane measurements on a large scale solid oxide fuel cell

Science.gov (United States)

Lengden, Michael; Cunningham, Robert; Johnstone, Walter

2011-10-01

A new in-line, real time gas analyser is described that uses tuneable diode laser spectroscopy (TDLS) for the measurement of methane in solid oxide fuel cells. The sensor has been tested on an operating solid oxide fuel cell (SOFC) in order to prove the fast response and accuracy of the technology as compared to a gas chromatograph. The advantages of using a TDLS system for process control in a large-scale, distributed power SOFC unit are described. In future work, the addition of new laser sources and wavelength modulation will allow the simultaneous measurement of methane, water vapour, carbon-dioxide and carbon-monoxide concentrations.

Influence of diet quantity on learning and memory ability and immunological function in mice

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

evaluate learning ability and the memory ability was retested at 24 hours later.Times of autonomic activity within 5 minutes were used to evaluate ability of autonomic activity.In addition,blood was collected from eyeball to measure plasma immune globulin and complement by using immunoturbidimetry.MAIN OUTCOME MEASURES:① Effect of different diet quantity on learning and memory ability;②effect of different diet quantity on times of autonomic activity and survival time under hypoxia and normal pressure;③ effect of different diet quantity on content of immune globulin and complement.RESULTS:All 80 mice were involved in the final analysis.① Effect of different diet quantity on learning and memory ability:There was no significant difference in learning ability during step down test (P＞0.05).While,memory ability in the over-diet group and the quantitative-diet group was better than that in the over-limit diet group (t=2.235 - 2.423,P＜0.05).During shuttle box test,learning and memory ability in the over-diet group was superior to that in the over-limit diet group (t =2.237 - 2.431,P＜0.05).While,memory ability in the quantitative-diet group and quantitative-limit diet group was superior to that in the over-limit group (t =2.704 - 2.813,P＜0.05).② Effect of different diet quantity on times of autonomic activity and survival time under hypoxia and normal pressure:There were significant differences in the times of autonomic activity among quantitative-diet group,quantitative-limit diet group and over-limit diet group (t=2.725 - 2.98,P＜0.05).Survival time in the quantitative-diet group and the quantitative-limit diet group was longer than that in the over-diet group (7=2.365,2.719,P＜0.05),but shorter than that in the over-limit diet group (t =2.427,2.538,P＜0.05).While,survival time in the over-limit diet group was longer than that in the over-diet group (t =2.765,P＜0.01).③Effect of different diet quantity on content of immune globulin and complement

Appraisal of Information Technology Requirements in Quantity Surveying Firms in Northern Nigeria

Directory of Open Access Journals (Sweden)

Y. U. Datti

2017-06-01

Full Text Available A worrisome trend in the adoption of emerging technologies for competitive advantages and improved productivities by QSs have been observed in that there is overwhelming evidence that there is an increasing usage of IT in quantity surveying firms but little or no noticeable benefits on the practice. It however becomes pertinent to ask then, that despite the increases adoption of computing and telecommunication technologies, why isn’t there any noticeable change due to the impacts of IT in the Nigerian Construction Industry with particular reference to Quantity Surveying practices. The study appraised the requirement of IT in quantity surveying practice in Nigeria. It examined the position of IT in quantity surveying firms in terms of its requirement and analyzed IT requirements-based problem constraining quantity surveying firms. The study is a survey research designed to obtain information on information technology in QS firms. A self-administered questionnaire was employed to quantity surveyors in consulting firms for responses. Responses were returned and analyzed using severity index and later ranked in order of importance. The results indicate a high level of computerization of professional services among the firms with greater number of their computers being networked. However, despite high level of networking of available computers, sharing of printers and other scarce tools/technologies are not established. Compared to developed countries such as Canada, Australia, United Kingdom and USA, the position of IT requirements in QS firms in Nigeria can be said to be at basic level with organization possessing and applying basic IT tools and technologies (e.g. scanners, digital cameras, dvd/cd-rom, general purpose software, QS application software, chat programs etc. in their daily operation and processes. While most firms are progressing toward intermediate level by possessing intermediate IT tools and technologies (e.g. teleconferencing

Characteristics Data Base: Programmer's guide to the LWR Quantities Data Base

International Nuclear Information System (INIS)

Jones, K.E.; Moore, R.S.

1990-08-01

The LWR Quantities Data Base is a menu-driven PC data base developed as part of OCRWM's waste, technical data base on the characteristics of potential repository wastes, which also includes non-LWR spent fuel, high-level and other materials. This programmer's guide completes the documentation for the LWR Quantities Data Base, the user's guide having been published previously. The PC data base itself may be requested from the Oak Ridge National Laboratory, using the order form provided in Volume 1 of publication DOE/RW-0184

Optimizing basin-scale coupled water quantity and water quality management with stochastic dynamic programming

DEFF Research Database (Denmark)

Davidsen, Claus; Liu, Suxia; Mo, Xingguo

2015-01-01

Few studies address water quality in hydro-economic models, which often focus primarily on optimal allocation of water quantities. Water quality and water quantity are closely coupled, and optimal management with focus solely on either quantity or quality may cause large costs in terms of the oth......-er component. In this study, we couple water quality and water quantity in a joint hydro-economic catchment-scale optimization problem. Stochastic dynamic programming (SDP) is used to minimize the basin-wide total costs arising from water allocation, water curtailment and water treatment. The simple water...... quality module can handle conservative pollutants, first order depletion and non-linear reactions. For demonstration purposes, we model pollutant releases as biochemical oxygen demand (BOD) and use the Streeter-Phelps equation for oxygen deficit to compute the resulting min-imum dissolved oxygen...

Coordinated Lot-sizing and Dynamic Prizing under a Supplier All-units Quantity Discount

Directory of Open Access Journals (Sweden)

Sandra Transchel

2008-05-01

Full Text Available We consider an economic order quantity model where the supplier offers an all-units quantity discount and a price sensitive customer demand. We compare a decentralized decision framework where selling price and replenishment policy are determined independently to simultaneous decision making. Constant and dynamic pricing are distinguished. We derive structural properties and develop algorithms that determine the optimal pricing and replenishment policy and show how quantity discounts not only influence the purchasing strategy but also the pricing policy. A sensitivity analysis indicates the impact of the fixed-holding cost ratio, the discount policy, and the customers' price sensitivity on the optimal decisions.

QUANTITY DISCOUNTS IN SUPPLIER SELECTION PROBLEM BY USE OF FUZZY MULTI-CRITERIA PROGRAMMING

Directory of Open Access Journals (Sweden)

Tunjo Perić

2011-02-01

Full Text Available Supplier selection in supply chain is a multi-criteria problem that involves a number of quantitative and qualitative factors. This paper deals with a concrete problem of flour purchase by a company that manufactures bakery products and the purchasing price of flour depends on the quantity ordered. The criteria for supplier selection and quantities supplied by individual suppliers are: purchase costs, product quality and reliability of suppliers. The problem is solved using a model that combines revised weighting method and fuzzy multi-criteria linear programming (FMCLP. The paper highlights the efficiency of the proposed methodology in conditions when purchasing prices depend on order quantities.

Determination of the quantity of acetyl CoA carboxylase by [14C]methyl avidin binding

International Nuclear Information System (INIS)

Roman-Lopez, C.R.; Goodson, J.; Allred, J.B.

1987-01-01

Conditions are described under which monomeric [ 14 C]methyl avidin binds to SDS-denatured biotin enzymes and remains bound through polyacrylamide gel electrophoresis. The location of radioactive proteins on the dried gel was determined by fluorography and their identity was established by subunit molecular weight. The relative quantity of bound radioactive avidin, stoichiometrically equivalent to the molar quantity of biotin protein, can be determined by scanning the fluorograph with a soft laser densitometer. To determine the absolute quantity of biotin protein, the radioactive areas of the dried gel were cut out, resolubilized, and assayed for radioactivity. Since the specific radioactivity of the [ 14 C]methyl avidin was known, the quantity of avidin bound and therefore the quantity of biotin enzyme could be calculated. The method is illustrated by the analysis of purified acetyl CoA carboxylase and is applied to the analysis of biotin enzymes in isolated rat liver mitochondria

PROBABILISTIC ANALYSES OF WASTE PACKAGE QUANTITIES IMPACTED BY POTENTIAL IGNEOUS DISRUPTION AT YUCCA MOUNTAIN

International Nuclear Information System (INIS)

M.G. Wallace

2005-01-01

A probabilistic analysis was conducted to estimate ranges for the numbers of waste packages that could be damaged in a potential future igneous event through a repository at Yucca Mountain. The analyses include disruption from an intrusive igneous event and from an extrusive volcanic event. This analysis supports the evaluation of the potential consequences of future igneous activity as part of the total system performance assessment for the license application for the Yucca Mountain Project (YMP). The first scenario, igneous intrusion, investigated the case where one or more igneous dikes intersect the repository. A swarm of dikes was characterized by distributions of length, width, azimuth, and number of dikes and the spacings between them. Through the use in part of a latin hypercube simulator and a modified video game engine, mathematical relationships were built between those parameters and the number of waste packages hit. Corresponding cumulative distribution function curves (CDFs) for the number of waste packages hit under several different scenarios were calculated. Variations in dike thickness ranges, as well as in repository magma bulkhead positions were examined through sensitivity studies. It was assumed that all waste packages in an emplacement drift would be impacted if that drift were intersected by a dike. Over 10,000 individual simulations were performed. Based on these calculations, out of a total of over 11,000 planned waste packages distributed over an area of approximately 5.5 km 2 , the median number of waste packages impacted was roughly 1/10 of the total. Individual cases ranged from 0 waste packages to the entire inventory being impacted. The igneous intrusion analysis involved an explicit characterization of dike-drift intersections, built upon various distributions that reflect the uncertainties associated with the inputs. The second igneous scenario, volcanic eruption (eruptive conduits), considered the effects of conduits formed in

Forecasting of municipal solid waste quantity in a developing country using multivariate grey models

International Nuclear Information System (INIS)

Intharathirat, Rotchana; Abdul Salam, P.; Kumar, S.; Untong, Akarapong

2015-01-01

Highlights: • Grey model can be used to forecast MSW quantity accurately with the limited data. • Prediction interval overcomes the uncertainty of MSW forecast effectively. • A multivariate model gives accuracy associated with factors affecting MSW quantity. • Population, urbanization, employment and household size play role for MSW quantity. - Abstract: In order to plan, manage and use municipal solid waste (MSW) in a sustainable way, accurate forecasting of MSW generation and composition plays a key role. It is difficult to carry out the reliable estimates using the existing models due to the limited data available in the developing countries. This study aims to forecast MSW collected in Thailand with prediction interval in long term period by using the optimized multivariate grey model which is the mathematical approach. For multivariate models, the representative factors of residential and commercial sectors affecting waste collected are identified, classified and quantified based on statistics and mathematics of grey system theory. Results show that GMC (1, 5), the grey model with convolution integral, is the most accurate with the least error of 1.16% MAPE. MSW collected would increase 1.40% per year from 43,435–44,994 tonnes per day in 2013 to 55,177–56,735 tonnes per day in 2030. This model also illustrates that population density is the most important factor affecting MSW collected, followed by urbanization, proportion employment and household size, respectively. These mean that the representative factors of commercial sector may affect more MSW collected than that of residential sector. Results can help decision makers to develop the measures and policies of waste management in long term period

Forecasting of municipal solid waste quantity in a developing country using multivariate grey models

Energy Technology Data Exchange (ETDEWEB)

Intharathirat, Rotchana, E-mail: rotchana.in@gmail.com [Energy Field of Study, School of Environment, Resources and Development, Asian Institute of Technology, P.O. Box 4, KlongLuang, Pathumthani 12120 (Thailand); Abdul Salam, P., E-mail: salam@ait.ac.th [Energy Field of Study, School of Environment, Resources and Development, Asian Institute of Technology, P.O. Box 4, KlongLuang, Pathumthani 12120 (Thailand); Kumar, S., E-mail: kumar@ait.ac.th [Energy Field of Study, School of Environment, Resources and Development, Asian Institute of Technology, P.O. Box 4, KlongLuang, Pathumthani 12120 (Thailand); Untong, Akarapong, E-mail: akarapong_un@hotmail.com [School of Tourism Development, Maejo University, Chiangmai (Thailand)

2015-05-15

Highlights: • Grey model can be used to forecast MSW quantity accurately with the limited data. • Prediction interval overcomes the uncertainty of MSW forecast effectively. • A multivariate model gives accuracy associated with factors affecting MSW quantity. • Population, urbanization, employment and household size play role for MSW quantity. - Abstract: In order to plan, manage and use municipal solid waste (MSW) in a sustainable way, accurate forecasting of MSW generation and composition plays a key role. It is difficult to carry out the reliable estimates using the existing models due to the limited data available in the developing countries. This study aims to forecast MSW collected in Thailand with prediction interval in long term period by using the optimized multivariate grey model which is the mathematical approach. For multivariate models, the representative factors of residential and commercial sectors affecting waste collected are identified, classified and quantified based on statistics and mathematics of grey system theory. Results show that GMC (1, 5), the grey model with convolution integral, is the most accurate with the least error of 1.16% MAPE. MSW collected would increase 1.40% per year from 43,435–44,994 tonnes per day in 2013 to 55,177–56,735 tonnes per day in 2030. This model also illustrates that population density is the most important factor affecting MSW collected, followed by urbanization, proportion employment and household size, respectively. These mean that the representative factors of commercial sector may affect more MSW collected than that of residential sector. Results can help decision makers to develop the measures and policies of waste management in long term period.

Design and development of microcontroller-based clinical chemistry analyser for measurement of various blood biochemistry parameters.

Science.gov (United States)

Taneja, S R; Gupta, R C; Kumar, Jagdish; Thariyan, K K; Verma, Sanjeev

2005-01-01

Clinical chemistry analyser is a high-performance microcontroller-based photometric biochemical analyser to measure various blood biochemical parameters such as blood glucose, urea, protein, bilirubin, and so forth, and also to measure and observe enzyme growth occurred while performing the other biochemical tests such as ALT (alkaline amino transferase), amylase, AST (aspartate amino transferase), and so forth. These tests are of great significance in biochemistry and used for diagnostic purposes and classifying various disorders and diseases such as diabetes, liver malfunctioning, renal diseases, and so forth. An inexpensive clinical chemistry analyser developed by the authors is described in this paper. This is an open system in which any reagent kit available in the market can be used. The system is based on the principle of absorbance transmittance photometry. System design is based around 80C31 microcontroller with RAM, EPROM, and peripheral interface devices. The developed system incorporates light source, an optical module, interference filters of various wave lengths, peltier device for maintaining required temperature of the mixture in flow cell, peristaltic pump for sample aspiration, graphic LCD display for displaying blood parameters, patients test results and kinetic test graph, 40 columns mini thermal printer, and also 32-key keyboard for executing various functions. The lab tests conducted on the instrument include versatility of the analyzer, flexibility of the software, and treatment of sample. The prototype was tested and evaluated over 1000 blood samples successfully for seventeen blood parameters. Evaluation was carried out at Government Medical College and Hospital, the Department of Biochemistry. The test results were found to be comparable with other standard instruments.

The impact of symbolic and non-symbolic quantity on spatial learning.

Directory of Open Access Journals (Sweden)

Koleen McCrink

Full Text Available An implicit mapping of number to space via a "mental number line" occurs automatically in adulthood. Here, we systematically explore the influence of differing representations of quantity (no quantity, non-symbolic magnitudes, and symbolic numbers and directional flow of stimuli (random flow, left-to-right, or right-to-left on learning and attention via a match-to-sample working memory task. When recalling a cognitively demanding string of spatial locations, subjects performed best when information was presented right-to-left. When non-symbolic or symbolic numerical arrays were embedded in these spatial locations, and mental number line congruency prompted, this effect was attenuated and in some cases reversed. In particular, low-performing female participants who viewed increasing non-symbolic number arrays paired with the spatial locations exhibited better recall for left-to-right directional flow information relative to right-to-left, and better processing for the left side of space relative to the right side of space. The presence of symbolic number during spatial learning enhanced recall to a greater degree than non-symbolic number--especially for female participants, and especially when cognitive load is high--and this difference was independent of directional flow of information. We conclude that quantity representations have the potential to scaffold spatial memory, but this potential is subtle, and mediated by the nature of the quantity and the gender and performance level of the learner.

The orientation distribution of tunneling-related quantities

Science.gov (United States)

Seif, W. M.; Refaie, A. I.; Botros, M. M.

2018-03-01

In the nuclear tunneling processes involving deformed nuclei, most of the tunneling-related quantities depend on the relative orientations of the participating nuclei. In the presence of different multipole deformations, we study the variation of a few relevant quantities for the α-decay and the sub-barrier fusion processes, in an orientation degree of freedom. The knocking frequency and the penetration probability are evaluated within the Wentzel-Kramers-Brillouin approximation. The interaction potential is calculated with Skyrme-type nucleon-nucleon interaction. We found that the width of the potential pocket, the Coulomb barrier radius, the penetration probability, the α-decay width, and the fusion cross-section follow consistently the orientation-angle variation of the radius of the deformed nucleus. The orientation distribution patterns of the pocket width, the barrier radius, the logarithms of the penetrability, the decay width, and the fusion cross-section are found to be highly analogous to pattern of the deformed-nucleus radius. The curve patterns of the orientation angle distributions of the internal pocket depth, the Coulomb barrier height and width, as well as the knocking frequency simulate inversely the variation of the deformed nucleus radius. The predicted orientation behaviors will be of a special interest in predicting the optimum orientations for the tunneling processes.

Reduction of trace quantities of chromium(VI by strong acids

Directory of Open Access Journals (Sweden)

Pezzin Sérgio H

2004-01-01

Full Text Available The chemical behavior of Cr(VI at low concentrations (10-4 to 10-7 mol L-1 in several strong acids was studied using high specific activity 51Cr(VI as a tracer. The speciation of the products from these systems was carried out by ion exchange chromatography with stepwise elution. The results show that trace quantities of Cr(VI, monitored by means of radiochromium (51Cr, are reduced in the presence of mineral acids such as perchloric, hydrochloric, hydrofluoric, sulfuric, nitric and trifluoromethanesulfonic acids, even in the absence of conventional reducing agents, producing different measureable Cr(III species, depending on the acid anion. Detailed studies of the reduction of low concentrations of Cr(VI with nitric acid have shown that the relative rate of reduction increases as the concentration of the acid increases or as the concentration of the Cr(VI decreases.

A Comparative Study of Face Milling of D2 Steel Using Al2O3 Based Nanofluid Minimum Quantity Lubrication and Minimum Quantity Lubrication

Directory of Open Access Journals (Sweden)

Muhammad Ahsan Ul Haq

2018-03-01

Full Text Available This study aims to investigate the effects of process parameters feed, depth of cut and flow rate, on the temperature during face milling of the D2 tool steel under two different lubricant conditions, Minimum Quantity Lubrication (MQL and Nanofluid Minimum Quantity Lubrication (NFMQL. Distilled water with the flow rate range 200-400 ml/hr was used in MQL. 2% by weight concentration of Al2O3 nanoparticles with distilled water as the base fluid used as NFMQL with same flow rate. Response surface methodology RSM central composite design CCD was used to design experiment run, modeling, and analysis. ANOVA was used for the adequacy and validation of the system. The comparison shows that NFMQL condition reduced more temperature during machining.

An Adaptive Information Quantity-Based Broadcast Protocol for Safety Services in VANET

Directory of Open Access Journals (Sweden)

Wenjie Wang

2016-01-01

Full Text Available Vehicle-to-vehicle communication plays a significantly important role in implementing safe and efficient road traffic. When disseminating safety messages in the network, the information quantity on safety packets changes over time and space. However, most of existing protocols view each packet the same to disseminate, preventing vehicles from collecting more recent and precise safety information. Hence, an information quantity-based broadcast protocol is proposed in this paper to ensure the efficiency of safety messages dissemination. In particular, we propose the concept of emergency-degree to evaluate packets’ information quantity. Then we present EDCast, an emergency-degree-based broadcast protocol. EDCast differentiates each packet’s priority for accessing the channel based on its emergency-degree so as to provide vehicles with more safety information timely and accurately. In addition, an adaptive scheme is presented to ensure fast dissemination of messages in different network condition. We compare the performance of EDCast with those of three other representative protocols in a typical highway scenario. Simulation results indicate that EDCast achieves higher broadcast efficiency and less redundancy with less delivery delay. What we found demonstrates that it is feasible and necessary for incorporating information quantity of messages in designing an efficient safety message broadcast protocol.

A modular method to handle multiple time-dependent quantities in Monte Carlo simulations

International Nuclear Information System (INIS)

Shin, J; Faddegon, B A; Perl, J; Schümann, J; Paganetti, H

2012-01-01

A general method for handling time-dependent quantities in Monte Carlo simulations was developed to make such simulations more accessible to the medical community for a wide range of applications in radiotherapy, including fluence and dose calculation. To describe time-dependent changes in the most general way, we developed a grammar of functions that we call ‘Time Features’. When a simulation quantity, such as the position of a geometrical object, an angle, a magnetic field, a current, etc, takes its value from a Time Feature, that quantity varies over time. The operation of time-dependent simulation was separated into distinct parts: the Sequence samples time values either sequentially at equal increments or randomly from a uniform distribution (allowing quantities to vary continuously in time), and then each time-dependent quantity is calculated according to its Time Feature. Due to this modular structure, time-dependent simulations, even in the presence of multiple time-dependent quantities, can be efficiently performed in a single simulation with any given time resolution. This approach has been implemented in TOPAS (TOol for PArticle Simulation), designed to make Monte Carlo simulations with Geant4 more accessible to both clinical and research physicists. To demonstrate the method, three clinical situations were simulated: a variable water column used to verify constancy of the Bragg peak of the Crocker Lab eye treatment facility of the University of California, the double-scattering treatment mode of the passive beam scattering system at Massachusetts General Hospital (MGH), where a spinning range modulator wheel accompanied by beam current modulation produces a spread-out Bragg peak, and the scanning mode at MGH, where time-dependent pulse shape, energy distribution and magnetic fields control Bragg peak positions. Results confirm the clinical applicability of the method. (paper)

Strategic Planning in Irish Quantity Surveying Pracitces

OpenAIRE

Murphy, Roisin

2011-01-01

The role and usefulness of strategic planning has been well documented over several decades of strategic management research. Despite the significant body of existing knowledge in the field of strategic planning, there remains a paucity of investigation into the construction sector, specifically in Professional Service Firms (PSF’s) operating within it. The aim of this research was to ascertain the type, scope and extent of strategic planning within Irish Quantity Surveying (QS) practices and...

Evaluation of a transposase protocol for rapid generation of shotgun high-throughput sequencing libraries from nanogram quantities of DNA.

Science.gov (United States)

Marine, Rachel; Polson, Shawn W; Ravel, Jacques; Hatfull, Graham; Russell, Daniel; Sullivan, Matthew; Syed, Fraz; Dumas, Michael; Wommack, K Eric

2011-11-01

Construction of DNA fragment libraries for next-generation sequencing can prove challenging, especially for samples with low DNA yield. Protocols devised to circumvent the problems associated with low starting quantities of DNA can result in amplification biases that skew the distribution of genomes in metagenomic data. Moreover, sample throughput can be slow, as current library construction techniques are time-consuming. This study evaluated Nextera, a new transposon-based method that is designed for quick production of DNA fragment libraries from a small quantity of DNA. The sequence read distribution across nine phage genomes in a mock viral assemblage met predictions for six of the least-abundant phages; however, the rank order of the most abundant phages differed slightly from predictions. De novo genome assemblies from Nextera libraries provided long contigs spanning over half of the phage genome; in four cases where full-length genome sequences were available for comparison, consensus sequences were found to match over 99% of the genome with near-perfect identity. Analysis of areas of low and high sequence coverage within phage genomes indicated that GC content may influence coverage of sequences from Nextera libraries. Comparisons of phage genomes prepared using both Nextera and a standard 454 FLX Titanium library preparation protocol suggested that the coverage biases according to GC content observed within the Nextera libraries were largely attributable to bias in the Nextera protocol rather than to the 454 sequencing technology. Nevertheless, given suitable sequence coverage, the Nextera protocol produced high-quality data for genomic studies. For metagenomics analyses, effects of GC amplification bias would need to be considered; however, the library preparation standardization that Nextera provides should benefit comparative metagenomic analyses.

Influences of the quantity of Mg2Sn phase on the corrosion behavior of Mg-7Sn magnesium alloy

International Nuclear Information System (INIS)

Liu Xianbin; Shan Dayong; Song Yingwei; Chen Rongshi; Han Enhou

2011-01-01

The influence of the quantity of the Mg 2 Sn phase on the corrosion behavior of different solution temperature treated Mg-7Sn magnesium alloy has been investigated by electrochemical measurements, scanning electron microscope (SEM) observation, X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis. With the increase of solution temperature, the quantity of Mg 2 Sn phase decreased and the tin concentration of matrix increased. The dissolved tin in Mg matrix took part in the film formation and the constituent of film was magnesium oxide and stannic oxide. The corrosion mode and corrosion rate were associated with the quantity of Mg 2 Sn phases and tin concentration of the matrix. If most of tin was present as Mg 2 Sn, the corrosion mode was pitting corrosion and it accelerated the corrosion rate. If most of tin was dissolved in matrix, the corrosion mode was filiform corrosion and it decreased the corrosion rate. The experiment evidences demonstrated that the corrosion resistance can be improved by increasing the tin concentration of matrix and the lowest corrosion rate was observed for sample solution treated at 540 o C.

Development of blueberry liquor: influence of distillate, sweetener and fruit quantity.

Science.gov (United States)

Caldeira, Ilda; Lopes, Daniel; Delgado, Teresa; Canas, Sara; Anjos, Ofélia

2018-02-01

In this work different formulations of blueberry liquor were tested and characterised based on their physico-chemical and sensory characteristics. Three factors were evaluated: the distillate used to produce the liquor (wine spirit or grape marc spirit); the sweetener (white sugar or honey) and the fruit quantity (two doses). For each liquor, pH, total acidity, dry soluble solids content, dry extract, alcoholic strength, reducing sugars, colour intensity, methanol content, acetaldehyde and fusel alcohols were determined. Sensory tests were carried out with a trained panel. The three factors studied significantly influenced the physico-chemical features of the liquors, being the quantity of fruit the most discriminating factor, except for the volatile compounds which were mainly influenced by the distillate. As regards the sensory analysis, it was found that the most appreciated liquor was that prepared with wine spirit, sugar and a lower dose of blueberry, and the less appreciated formulation was the one made with grape marc spirit, honey and a lower quantity of blueberry. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Aggregating land use quantity and intensity to link water quality in upper catchment of Miyun Reservoir

Science.gov (United States)

Xu, E.

2015-12-01

Land use is closely related to hydrological and biochemical processes influencing the water quality. Quantifying relationship between both of them can help effectively manage land use to improve water quality. Previous studies majorly utilized land use quantity as an indicator to link water quality parameters, which lacked an insight to the influence of land use intensity. Taking upper catchment of Miyun Reservoir as a case study, we proposed a method of aggregating land use quantity and intensity to build a new land use indicator and investigated its explanation empower on water quality. Six nutrient concentrations from 52 sub-watersheds covering the whole catchment were used to characterize spatial distributions of water eutrophication. Based on spatial techniques and empirical conversion coefficients, combined remote sensing with socio-economic statistical data, land use intensity was measured and mapped visually. Then the new land use indicator was calculated and linked to nutrient concentrations by Pearson correlation coefficients. Results demonstrated that our new land use indicator incorporating intensity information can quantify the potential different nutrients exporting abilities from land uses. Comparing to traditional indicators only characterized by land use quantity, most Pearson correlation coefficients between new indicator and water nutrient concentrations increased. New information enhanced the explanatory power of land use on water nutrient concentrations. Then it can help better understand the impact of land use on water quality and guide land use management for supporting decision making.

Estimating waste disposal quantities from raw waste samples

International Nuclear Information System (INIS)

Negin, C.A.; Urland, C.S.; Hitz, C.G.; GPU Nuclear Corp., Middletown, PA)

1985-01-01

Estimating the disposal quantity of waste resulting from stabilization of radioactive sludge is complex because of the many factors relating to sample analysis results, radioactive decay, allowable disposal concentrations, and options for disposal containers. To facilitate this estimation, a microcomputer spread sheet template was created. The spread sheet has saved considerable engineering hours. 1 fig., 3 tabs

Measurements of gluon spin-sensitive quantities at the Z0 resonance

International Nuclear Information System (INIS)

Fan, C.G.

1993-10-01

Measurements have been made of the scaled jet energies (x 1 , x 2 , x 3 ) and the Ellis-Karliner angle (cosθ EK ), which are sensitive to the spill of the gluon, in the 3-jet hadronic events from the e + e - annihilation at the Z 0 resonance. The experiment is performed with the SLD detector at the Stanford Linear Accelerator Center (SLAC). The data used in this analysis was collected during the 1992 physics run, which includes 10,252 hadronic Z 0 events that have CDC information written out. Only charged tracks measured in the central drift chamber are used for the measurements of the above variables. The raw data are found to be in good agreement with the Monte Carlo simulations passing the same set of track and event selection cuts. A bin-to-bin correction is done for the distributions of x 1 , x 2 , x 3 , and cosθ EK to account for the effects of hadronization, detector acceptance and resolution. The corrected data is compared to the parton level distributions of x 1 , x 2 , x 3 , and cosθ EK simulated from the vector QCD model and the scalar gluon model respectively. The systematic errors, calculated for all the bins in these distributions, are obtained by comparing the results from different sets of track and event selection cuts, from different hadronization models and from different Monte Carlo programs. Good agreement is found between data and the vector QCD model. The scalar gluon model strongly disagrees with the data

Changes in sleep quantity and efficiency in professional rugby union players during home based training and match-play.

Science.gov (United States)

Eagles, A; Mclellan, C; Hing, W; Carloss, N; Lovell, D

2014-11-04

Adequate sleep is paramount to athlete recovery and performance, however little is know about the typical sleep patterns of professional rugby union players during home based training and match-play in the competitive season. The aim of the present study was to monitor changes in sleep quantity and efficiency of elite male rugby union players over a twelve night period, which included training and two competitive matches. A total of ten elite male rugby union players from a selected team, participated in the study. Athletes sleep quantity and efficiency was monitored over a twelve night period using the Bodymedia sensewear units (BSU). There was a significant difference in sleep quantity (pwake over the twelve night period. Sleep efficiency is defined as a percentage score calculated by incorporating movement and physiological measures over the sleep duration as determined by the BSU. Also there was no significant difference between sleep parameters on the game nights. The findings show players have significantly (p<0.05) reduced sleep following a home game, which is of concern considering the established negative influence of sleep deprivation on cognitive and physical performance. This data may assist coaching, medical and performance staff to develop and implement team and individualised sleep monitoring regimes to optimise training and on-field performance.

A bottom-up approach in estimating the measurement uncertainty and other important considerations for quantitative analyses in drug testing for horses.

Science.gov (United States)

Leung, Gary N W; Ho, Emmie N M; Kwok, W Him; Leung, David K K; Tang, Francis P W; Wan, Terence S M; Wong, April S Y; Wong, Colton H F; Wong, Jenny K Y; Yu, Nola H

2007-09-07

Quantitative determination, particularly for threshold substances in biological samples, is much more demanding than qualitative identification. A proper assessment of any quantitative determination is the measurement uncertainty (MU) associated with the determined value. The International Standard ISO/IEC 17025, "General requirements for the competence of testing and calibration laboratories", has more prescriptive requirements on the MU than its superseded document, ISO/IEC Guide 25. Under the 2005 or 1999 versions of the new standard, an estimation of the MU is mandatory for all quantitative determinations. To comply with the new requirement, a protocol was established in the authors' laboratory in 2001. The protocol has since evolved based on our practical experience, and a refined version was adopted in 2004. This paper describes our approach in establishing the MU, as well as some other important considerations, for the quantification of threshold substances in biological samples as applied in the area of doping control for horses. The testing of threshold substances can be viewed as a compliance test (or testing to a specified limit). As such, it should only be necessary to establish the MU at the threshold level. The steps in a "Bottom-Up" approach adopted by us are similar to those described in the EURACHEM/CITAC guide, "Quantifying Uncertainty in Analytical Measurement". They involve first specifying the measurand, including the relationship between the measurand and the input quantities upon which it depends. This is followed by identifying all applicable uncertainty contributions using a "cause and effect" diagram. The magnitude of each uncertainty component is then calculated and converted to a standard uncertainty. A recovery study is also conducted to determine if the method bias is significant and whether a recovery (or correction) factor needs to be applied. All standard uncertainties with values greater than 30% of the largest one are then used to

Development and Validation of the Marijuana Motives Measure Short Form.

Science.gov (United States)

Mezquita, Laura; Ruiz-Valero, Lucía; Martínez-Gómez, Naiara; Ibáñez, Manuel I; Ortet, Generós

2018-01-15

Marijuana motives are a proximal variable to marijuana use. This research aimed to adapt and validate the short form of the Marijuana Motives Measure (MMM; Simons, Correia, Carey, y Borsari, 1998), the MMM SF, in Spanish.  The sample comprised 232 participants (mean age = 25.11 (7.58), 50.43% males) who had tried marijuana at least once in their lifetime. Item and Rasch analyses were performed to choose the final pool of 15 items. Confirmatory Factor Analysis (CFA) showed an adequate 5-factor structure (S-BX2(80) = 121.30, p = .002; NNFI = .944; CFI = .958; IFI = .959; MFI = .915; RMSEA = .047(0.029, 0.063); AIC = -38.70), and the multi-group CFA between males and females showed acceptable fit indices (S-BX2(160) = 230.01, p = .000; NNFI = .900; CFI = .924; IFI = .927; MFI = .860; RMSEA = .062(.043, .078); AIC = -89.99). The questionnaire indicated metric (S-BX2diff (15) = 13.61, p = .556)), scalar (S-BX2diff (15) = 23.15, p = .081)) and error measurement invariance (S-BX2diff (15) = 8.65, p = .895)) between gender groups. The internal consistencies and ordinal omega of the scales were between .79 and .90. In the regression analysis, enhancement, coping and low conformity motives predicted frequency and quantity of marijuana smoked. The best predictor of frequency and quantity consumed during the heaviest smoking period was enhancement, while coping and, to a lesser extent, low conformity, were the only predictors of cannabis-related problems when marijuana frequency and quantity were controlled for.  The MMM SF shows adequate psychometric properties and is a suitable instrument to assess marijuana motives, especially during time-limited sessions.

Prefrontal cortex and sensory cortices during working memory: quantity and quality.

Science.gov (United States)

Ku, Yixuan; Bodner, Mark; Zhou, Yong-Di

2015-04-01

The activity in sensory cortices and the prefrontal cortex (PFC) throughout the delay interval of working memory (WM) tasks reflect two aspects of WM-quality and quantity, respectively. The delay activity in sensory cortices is fine-tuned to sensory information and forms the neural basis of the precision of WM storage, while the delay activity in the PFC appears to represent behavioral goals and filters out irrelevant distractions, forming the neural basis of the quantity of task-relevant information in WM. The PFC and sensory cortices interact through different frequency bands of neuronal oscillation (theta, alpha, and gamma) to fulfill goal-directed behaviors.

Non-Noether conserved quantity for differential equations of motion in the phase space

Institute of Scientific and Technical Information of China (English)

无

2002-01-01

A non-Noether conserved quantity for the differential equations of motion of mechanical systems in the phase space is studied. The differential equations of motion of the systems are established and the determining equations of Lie symmetry are given. An existence theorem of non-Noether conserved quantity is obtained. An example is given to illustrate the application of the result.

Measurement of Indirect CP Violation in Charm at LHCb

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00342046

This thesis describes two pieces of work. The first is a study of the resolution of the LHCb vertex locator throughout Run 1. The second comprises analyses to measure the charm mixing and $CP$ violation observables $A_{\\Gamma}$ and $y_{CP}$. An estimate of the resolution of the LHCb vertex locator is required for use in the track fits. A method to measure the resolution with collision data has been developed and tested. The performance of the sub-detector throughout Run 1 of the LHC has been assessed. A significant degrading of the resolution has been seen. The effects of this on the track reconstruction has been examined with little change in the measured quantities being observed. The measurement of indirect $CP$ violation in neutral $D$ meson transitions has been measured through the observables $A_{\\Gamma}$ and $y_{CP}$, using $fb^{-1}$ of $pp$ collisions with a centre of mass energy $7 TeV$, collected by the LHCb detector in 2011. $A_{\\Gamma}$ describes the $CP$ asymmetry of the lifetime of the $D^0$ dec...

Does quantity generate quality? Testing the fundamental principle of brainstorming.

Science.gov (United States)

Muñoz Adánez, Alfredo

2005-11-01

The purpose of this work is to test the chief principle of brainstorming, formulated as "quantity generates quality." The study is included within a broad program whose goal is to detect the strong and weak points of creative techniques. In a sample of 69 groups, containing between 3 and 8 members, the concurrence of two commonly accepted criteria was established as a quality rule: originality and utility or value. The results fully support the quantity-quality relation (r = .893): the more ideas produced to solve a problem, the better quality of the ideas. The importance of this finding, which supports Osborn's theory, is discussed, and the use of brainstorming is recommended to solve the many open problems faced by our society.

Wake field measurements

International Nuclear Information System (INIS)

Palumbo, L.

1989-01-01

In this paper the concept of Wakefields and Machine Impedance are introduced. Several measurements technique of these quantities either in the laboratory before installation or from beam observation are presented

40 CFR 355.12 - What quantities of extremely hazardous substances trigger emergency planning requirements?

Science.gov (United States)

2010-07-01

... EMERGENCY PLANNING AND NOTIFICATION Emergency Planning Who Must Comply § 355.12 What quantities of extremely... 40 Protection of Environment 27 2010-07-01 2010-07-01 false What quantities of extremely hazardous substances trigger emergency planning requirements? 355.12 Section 355.12 Protection of Environment...

Diffusion and the self-measurability

Directory of Open Access Journals (Sweden)

Holeček M.

2009-06-01

Full Text Available The familiar diffusion equation, ∂g/∂t = DΔg, is studied by using the spatially averaged quantities. A non-local relation, so-called the self-measurability condition, fulfilled by this equation is obtained. We define a broad class of diffusion equations defined by some "diffusion inequality", ∂g/∂t · Δg ≥ 0, and show that it is equivalent to the self-measurability condition. It allows formulating the diffusion inequality in a non-local form. That represents an essential generalization of the diffusion problem in the case when the field g(x, t is not smooth. We derive a general differential equation for averaged quantities coming from the self-measurability condition.

16 CFR 500.13 - Measurement of commodities by area measure only, how expressed.

Science.gov (United States)

2010-01-01

... commodities by area measure only, how expressed. For commodities measured in terms of area measure only declaration of net quantity in terms of square yards, square feet, and square inches shall be expressed in the... only, how expressed. 500.13 Section 500.13 Commercial Practices FEDERAL TRADE COMMISSION RULES...

Evaluation of the practical peak voltage quantity for clinical equipment in diagnostic radiology

International Nuclear Information System (INIS)

Pires, Joao dos Santos Justo

2007-01-01

The objective of this work is to evaluate the calculation of the Practical Peak Voltage (PPV) from the voltage waveform and the kerma contrast for two kinds of X-ray equipment: a single phase clinical equipment, a three phase clinical equipment. The PPV from a mammography system voltage waveform will also be established. The development of this work involves intermediate objectives that indicate the quality of the used methods to calculate the PPV. One of these intermediate objectives is the comparison between the invasive calculations of PPV (using a voltage divider) with the response of kVp meter that calculate the PPV. Another intermediate objective is to compare the PPV with the Contrast Equivalent Voltage (the original non-invasive PPV definition). The variation of the PPV with quantities that influence in the voltage waveform like ripple and sample rate will also be contemplated in this work. The results showed that the PPV quantity could be invasive determined trustworthy. Therefore, the ripple quantity is the mainly influence to determinate the PPV that affecting the non-invasive determination. This fact suggest that the non-invasive instruments manufacturers must reevaluate the calculation of the PPV quantity in their instruments. (author)

41 CFR 101-26.507-4 - Quantities in excess of the maximum order limitation.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Quantities in excess of... Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND PROGRAM 26.5-GSA Procurement Programs § 101-26.507-4 Quantities in...

Competition and facilitation between a native and a domestic herbivore: trade-offs between forage quantity and quality.

Science.gov (United States)

Augustine, David J; Springer, Tim L

2013-06-01

Potential competition between native and domestic herbivores is a major consideration influencing the management and conservation of native herbivores in rangeland ecosystems. In grasslands of the North American Great Plains, black-tailed prairie dogs (Cynomys ludovicianus) are widely viewed as competitors with cattle but are also important for biodiversity conservation due to their role in creating habitat for other native species. We examined spatiotemporal variation in prairie dog effects on growing-season forage quality and quantity using measurements from three colony complexes in Colorado and South Dakota and from a previous study of a fourth complex in Montana. At two complexes experiencing below-average precipitation, forage availability both on and off colonies was so low (12-54 g/m2) that daily forage intake rates of cattle were likely constrained by instantaneous intake rates and daily foraging time. Under these dry conditions, prairie dogs (1) substantially reduced forage availability, thus further limiting cattle daily intake rates, and (2) had either no or a small positive effect on forage digestibility. Under such conditions, prairie dogs are likely to compete with cattle in direct proportion to their abundance. For two complexes experiencing above-average precipitation, forage quantity on and off colonies (77-208 g/m2) was sufficient for daily forage intake of cattle to be limited by digestion rather than instantaneous forage intake. At one complex where prairie dogs enhanced forage digestibility and [N] while having no effect on forage quantity, prairie dogs are predicted to facilitate cattle mass gains regardless of prairie dog abundance. At the second complex where prairie dogs enhanced digestibility and [N] but reduced forage quantity, effects on cattle can vary from competition to facilitation depending on prairie dog abundance. Our findings show that the high spatiotemporal variation in vegetation dynamics characteristic of semiarid grasslands

Quantity, Quality, and Satisfaction with Mentoring: What Matters Most?

Science.gov (United States)

Xu, Xiaohong; Payne, Stephanie C.

2014-01-01

According to Kram's mentor role theory, satisfaction with mentoring and mentorship quality are key indicators of effective and successful mentoring. We contribute to mentoring research by demonstrating the relative importance of mentorship quantity, mentorship quality, and satisfaction with mentoring to the prediction of job satisfaction,…

The measurement of sparkle

Science.gov (United States)

Ferrero, A.; Bayón, S.

2015-04-01

Sparkle is a non-uniform texture effect consisting of very bright spots distributed on a dark surround. To date the only commercially-available instrument able to quantify sparkle is BYK-mac. This instrument allows sparkle parameters to be obtained, which should correlate with the visual experience. However, the measurands corresponding to these parameters are not clearly defined and they cannot be measured by any other instruments. In this article, we describe a procedure to measure quantities of well-defined sparkle measurands. We present experimental results at a combination of well-distributed illumination/viewing geometries within the incident plane. From this study, four descriptors are derived which may be correlated with visual attributes of sparkle. Finally, the procedure to estimate the perceived sparkle at any given surround luminance from the measured sparkle quantities is explained.

Time trends in dietary fat intake in a sample of German children and adolescents between 2000 and 2010: not quantity, but quality is the issue.

Science.gov (United States)

Libuda, Lars; Alexy, Ute; Kersting, Mathilde

2014-01-14

Dietary fat intake in childhood may influence the risk for developing chronic diseases. The objective of the present study was to examine secular trends in the parameters of fat intake between 2000 and 2010 in a sample of German children and adolescents (n 808) participating in the Dortmund Nutritional and Anthropometric Longitudinally Designed (DONALD) Study. Dietary data from 4380 3 d weighed dietary records were analysed using repeated-measures regression to determine time trends in fat quantity, i.e. the intake of total fat, and in fat quality, i.e. the ratios of SFA, MUFA and PUFA. In young children (2-3 years) and in adolescents (13-18 years), total fat intake remained stable over time, but decreased by 0·08 % of total energy (%E) per year in 4-12-year-old children. In 2010, median fat intake was at the upper end of the recommendations. SFA intake decreased slightly in 2-3- and 4-12-year-old children by 0·09 and 0·05 %E per year, respectively. MUFA and PUFA intakes remained stable in all the age groups except in adolescents. Here, PUFA intake decreased initially, but increased between 2005 and 2010. In 2010, only between 3 and 18 % of the respective age groups had an intake of SFA or PUFA within the recommendations. In conclusion, fat quantity and quality did not change substantially between 2000 and 2010. Fat quality, in particular, needs to be improved, since a large percentage of our sample did not meet the recommended intakes for SFA and PUFA.

Quantities of uranium-235 buried in disposal boxes, 1985--1991

International Nuclear Information System (INIS)

Cook, J.R.

1991-01-01

IWT was asked by J. R. Schornhorst of NPSR to determine the distribution of the quantity of enriched uranium per disposal box (B-25) of the years 1985--1991 to provide input to an uptake of the E Area Safety Analysis. This information was considered important since the issue of criticality is an important concern in safety analyses. Information found in the COBRA data base shows no disposal containers exceeded 100 grams of U-235. The COBRA data base was queried in a two-step process. First a short program in the NATURAL language was used to retrieve all records beginning with January 1983 having a Burial Code of less than 4, indicating low-level waste disposed in trenches. These records were then passed to a temporary storage file and read into a program written in Statistical Analysis System (SAS) language. SAS was used to eliminate waste from the Naval Fuel Facility, which will not operate in the future, and to sort the records in order of increasing amounts of U-235. The SAS procedure FREQ was then used to produce a cumulative frequency distribution of grams of U-235. A total of 53,198 packages were disposed of during this time period, 277 of which contained U-235. The programs used and resulting output are attached as Appendix I

Cloud-based bioinformatics workflow platform for large-scale next-generation sequencing analyses.

Science.gov (United States)

Liu, Bo; Madduri, Ravi K; Sotomayor, Borja; Chard, Kyle; Lacinski, Lukasz; Dave, Utpal J; Li, Jianqiang; Liu, Chunchen; Foster, Ian T

2014-06-01

Due to the upcoming data deluge of genome data, the need for storing and processing large-scale genome data, easy access to biomedical analyses tools, efficient data sharing and retrieval has presented significant challenges. The variability in data volume results in variable computing and storage requirements, therefore biomedical researchers are pursuing more reliable, dynamic and convenient methods for conducting sequencing analyses. This paper proposes a Cloud-based bioinformatics workflow platform for large-scale next-generation sequencing analyses, which enables reliable and highly scalable execution of sequencing analyses workflows in a fully automated manner. Our platform extends the existing Galaxy workflow system by adding data management capabilities for transferring large quantities of data efficiently and reliably (via Globus Transfer), domain-specific analyses tools preconfigured for immediate use by researchers (via user-specific tools integration), automatic deployment on Cloud for on-demand resource allocation and pay-as-you-go pricing (via Globus Provision), a Cloud provisioning tool for auto-scaling (via HTCondor scheduler), and the support for validating the correctness of workflows (via semantic verification tools). Two bioinformatics workflow use cases as well as performance evaluation are presented to validate the feasibility of the proposed approach. Copyright © 2014 Elsevier Inc. All rights reserved.

Dynamics of leaf litter humidity, depth and quantity: two restoration strategies failed to mimic ground microhabitat conditions of a low montane and premontane forest in Costa Rica

Directory of Open Access Journals (Sweden)

Zaidett Barrientos

2012-09-01

Full Text Available Little is known about how restoration strategies affect aspects like leaf litter’s quantity, depth and humidity. I analyzed leaf litter’s quantity, depth and humidity yearly patterns in a primary tropical lower montane wet forest and two restored areas: a 15 year old secondary forest (unassisted restoration and a 40 year old Cupressus lusitanica plantation (natural understory. The three habitats are located in the Río Macho Forest Reserve, Costa Rica. Twenty litter samples were taken every three months (April 2009-April 2010 in each habitat; humidity was measured in 439g samples (average, depth and quantity were measured in five points inside 50x50cm plots. None of the restoration strategies reproduced the primary forest leaf litter humidity, depth and quantity yearly patterns. Primary forest leaf litter humidity was higher and more stable (x=73.2, followed by secondary forest (x=63.3 and cypress plantation (x=52.9 (Kruskall-Wallis=77.93, n=232, p=0.00. In the primary (Kruskal-Wallis=31.63, n=78, p<0.001 and secondary (Kruskal-Wallis=11.79, n=75, p=0.008 forest litter accumulation was higher during April due to strong winds. In the primary forest (Kruskal-wallis=21.83, n=78, p<0.001 and the cypress plantation (Kruskal-wallis=39.99, n=80, p<0.001 leaf litter depth was shallow in October because heavy rains compacted it. Depth patterns were different from quantity patterns and described the leaf litter’s structure in different ecosystems though the year.

A measure of localization properties of one-dimensional single electron lattice systems

International Nuclear Information System (INIS)

Gong, Longyan; Li, Wenjia; Zhao, Shengmei; Cheng, Weiwen

2016-01-01

We propose a novel quantity to measure the degree of localization properties of various types of one-dimension single electron states. The quantity includes information about the spatial variation of probability density of quantum states. Numerical results show that it can distinguish localized states from delocalized ones, so it can be used as a fruitful index to monitor the localization–delocalization transition. Comparing with existing measures, such as geometric average density of states, inverse participation ratio, and quantum information entropies, our proposed quantity has some advantages over them. - Highlights: • A novel quantity is proposed to measure the degree of localization. • It includes information about the spatial variation of probability density. • It is a fruitful index to monitor the localization–delocalization transition.

MATERNAL ALCOHOL CONSUMPTION PRODUCING FETAL ALCOHOL SPECTRUM DISORDERS (FASD): QUANTITY, FREQUENCY, AND TIMING OF DRINKING

Science.gov (United States)

May, Philip A.; Blankenship, Jason; Marais, Anna-Susan; Gossage, J. Phillip; Kalberg, Wendy O.; Joubert, Belinda; Cloete, Marise; Barnard, Ronel; De Vries, Marlene; Hasken, Julie; Robinson, Luther K.; Adnams, Colleen M.; Buckley, David; Manning, Melanie; Parry, Charles; Hoyme, H. Eugene; Tabachnick, Barbara; Seedat, Soraya

2013-01-01

Background Concise, accurate measures of maternal prenatal alcohol use are needed to better understand fetal alcohol spectrum disorders (FASD). Methods Measures of drinking by mothers of children with specific FASD diagnoses and mothers of randomly-selected controls are compared and also correlated with physical and cognitive/behavioral outcomes. Results Measures of maternal alcohol use can differentiate maternal drinking associated with FASD from that of controls and some from mothers of alcohol-exposed normals. Six variables that combine quantity and frequency concepts distinguish mothers of FASD children from normal controls. Alcohol use variables, when applied to each trimester and three months prior to pregnancy, provide insight on critical timing of exposure as well. Measures of drinking, especially bingeing, correlate significantly with increased child dysmorphology and negative cognitive/behavioral outcomes in children, especially low non-verbal IQ, poor attention, and behavioral problems. Logistic regression links (palcohol consumption both within and between diagnostic groupings of mothers bearing children diagnosed within the FASD continuum. Drinking measures are empirically identified and correlated with specific child outcomes. Alcohol use, especially heavy use, should be avoided throughout pregnancy. PMID:23932841

Pharmaceutical quantities of yohimbine found in dietary supplements in the USA.

Science.gov (United States)

Cohen, Pieter A; Wang, Yan-Hong; Maller, Gregory; DeSouza, Renan; Khan, Ikhlas A

2016-01-01

In the USA, botanical dietary supplements are presumed to be safe, but this is not necessarily always the case. Extracts of the evergreen tree yohimbe, Pausinystalia johimbe, though banned in many countries, are sold in hundreds of dietary supplements in the USA. We analyzed 49 brands of supplements labelled as containing yohimbe or yohimbine available for sale from seven major retailers in the USA. Supplements were analyzed using ultra high-performance liquid chromatography coupled to photodiode and quadrupole time-of-flight mass spectrometry detectors for quantity of three alkaloids found in P. johimbe (yohimbine, rauwolscine, and corynanthine). The alkaloids were confirmed on the basis of retention time, ultraviolet spectra, and mass spectra against reference standards. The quantity of the most active alkaloid, yohimbine, per recommended serving ranged from none detected to 12.1 mg. Thirty-nine percent of the supplements (19/49) did not contain rauwolscine and corynanthine suggesting that the yohimbine was either from highly processed plant extract or synthetic in origin. Only 11 supplement brands (22%, 11/49) listed a specific quantity of yohimbine on the label. Most of these were inaccurately labelled (actual content ranged from 23% to 147% of the content on the label). Eighteen percent (9/49) of the supplements' labels did not provide any information about yohimbine's adverse effects. Of the 49 yohimbine supplement brands sold at seven major retail chains in the USA, only 4.1% (2/49) provided consumers with both accurate information about the quantity of yohimbine as well as information about yohimbine's known adverse effects. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Determination of post-shakedown quantities of a pipe bend via the simplified theory of plastic zones compared with load history dependent incremental analysis

Science.gov (United States)

Vollrath, Bastian; Hübel, Hartwig

2018-01-01

The Simplified Theory of Plastic Zones (STPZ) may be used to determine post-shakedown quantities such as strain ranges and accumulated strains at plastic or elastic shakedown. The principles of the method are summarized. Its practical applicability is shown by the example of a pipe bend subjected to constant internal pressure along with cyclic in-plane bending or/and cyclic radial temperature gradient. The results are compared with incremental analyses performed step-by-step throughout the entire load history until the state of plastic shakedown is achieved.

Estimation of Waste Quantities Using DeCAT-Pro

Energy Technology Data Exchange (ETDEWEB)

Yun, Taesik; Jung, Hyejin; Oh, Jaeyoung; Kim, Younggook [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The D and D (Dismantling and Decontamination) is scheduled to get started in June 2022 elapsing five years of cooling spent fuels down. The final site status is postulated as Brown Field and tentative DCGL of less than 0.1 mSv per year to evaluate waste quantities in a conservative manner. The decommissioning strategy was determined the immediate decommissioning whose whole period would be taken for approximately 15 years; pre-decommissioning for two years, spent fuel cool-down for five years, D and D for six years, site remediation for two years. The assumption to dismantle the underground facilities including SSCs is to one meter beneath the ground level and the other facilities remain intact. In addition, non-radioactive concrete wastes would be used to landfill gaps of the remaining facilities. Although there are many assumptions we applied, the methodologies developed and the data produced by this research will play a meaningful role as a good starting point for the Kori-1 decommissioning after its shutdown to logically and reasonably estimate the waste quantity. However it is clear that tenacious efforts should be taken to successfully perform the decommissioning project.

Water quality and quantity investigation of green roofs in a dry climate.

Science.gov (United States)

Beecham, S; Razzaghmanesh, M

2015-03-01

Low-energy pollutant removal strategies are now being sought for water sensitive urban design. This paper describes investigations into the water quality and quantity of sixteen, low-maintenance and unfertilized intensive and extensive green roof beds. The factors of Slope (1° and 25°), Depth (100 mm and 300 mm), Growing media (type A, type B and type C) and Species (P1, P2 and P3) were randomized according to a split-split plot design. This consisted of twelve vegetated green roof beds and four non-vegetated beds as controls. Stormwater runoff was collected from drainage points that were installed in each area. Samples of run-off were collected for five rainfall events and analysed for water retention capacity and the water quality parameters of NO₂, NO₃, NH₄, PO₄, pH, EC, TDS, Turbidity, Na, Ca, Mg and K. The results indicated significant differences in terms of stormwater water quality and quantity between the outflows of vegetated and non-vegetated systems. The water retention was between 51% and 96% and this range was attributed to the green roof configurations in the experiment. Comparing the quality of rainfall as inflow, and the quality of runoff from the systems showed that green roofs generally acted as a source of pollutants in this study. In the vegetated beds, the intensive green roofs performed better than the extensive beds with regard to outflow quality while in the non-vegetated beds, the extensive beds performed better than intensive systems. This highlights the importance of vegetation in improving water retention capacity as well as the role of vegetation in enhancing pollutant removal in green roof systems. In addition growing media with less organic matter had better water quality performance. Comparison of these results with national and international standards for water reuse confirmed that the green roof outflow was suitable for non-potable uses such as landscape irrigation and toilet flushing. Copyright © 2014 Elsevier Ltd. All

Mei Symmetry and New Conserved Quantities of Tzénoff Equations for the Variable Mass Higher-Order Nonholonomic System

Institute of Scientific and Technical Information of China (English)

ZHENG Shi-Wang; WANG Jian-Bo; CHEN Xiang-Wei; XIE Jia-Fang

2012-01-01

Operational systems of spacecraft are general variable mass mechanics systems,and their symmetries and conserved quantities imply profound physical rules of the space system.We study the Mei symmetry of Tzénoff equations for a variable mass nonholonomic system and the new conserved quantities derived.The function expression of the new conserved quantities and the criterion equation which deduces these conserved quantities are presented.This result has some theoretical values in further research of conservation laws obeyed by the variable mass system.%Operational systems of spacecraft are general variable mass mechanics systems, and their symmetries and conserved quantities imply profound physical rules of the space system. We study the Mei symmetry of Tzenoff equations for a variable mass nonholonomic system and the new conserved quantities derived. The function expression of the new conserved quantities and the criterion equation which deduces these conserved quantities are presented. This result has some theoretical values in further research of conservation laws obeyed by the variable mass system.

Procedure and device for the radiometric determination of the quantity, quality and foreign substances in moved bulk materials

International Nuclear Information System (INIS)

Krone, C.; Jentsch, G.; Berger, J.

1987-01-01

This invention has to do with a procedure and device for the simultaneous radiometric determination of quantity, quality and foreign substances in moved bulk materials in particular lignite at one measuring point. The section of the bulk material discharge is transmitted by nuclides for soft and hard gamma radiation in pairs. The pulse rates are registered in pairs by means of detectors and evaluated in real-time operation

Study of dosimetric quantities and image quality in pediatric examinations of chest and abdomen computed tomography

International Nuclear Information System (INIS)

Jornada, Tiago da Silva

2013-01-01

This work had the objective to achieve the knowledge of the dosimetric quantities related to chest and abdomen computed tomography (CT) examinations of pediatric patients, in Belo Horizonte city. The reason of this work is based on the fact that the probability of health detriment in children, which it may be caused by radiation, is higher than in adults. Besides, although in many countries the knowledge and control of patient doses is a normal procedure, this safety culture does not exist in Brazil. Another objective of this work was to compare the dosimetric quantity values with the Diagnostic Reference Levels (DRLs); when it was needed, an optimization process was applied and the quality of the diagnostic image obtained with the optimized technical parameters was analyzed. This study was carried out in five hospitals, where the weighted air kerma index (Cw), the volumetric air kerma index (Cvol), the air kerma - length product (PKL,CT), the Effective Dose (E) and the Normalized Effective Dose (En) were determined; three methods were adopted for measurements: the ionization chamber inside a chest pediatric phantom, radiochromic films and the CT-EXPO software. The optimization process was applied to a single hospital through variations in the current (mA) and voltage (kV) of the x-ray tube for the protocols used for abdomen CT examinations. The analysis of the quality of the diagnostic image was done by Normal Distribution and ROC analysis; spatial resolution analysis was used through MTF determination and the noise level was judged in terms quantitative and qualitative. Results of the dosimetric quantities showed that they significantly differed between single-slice and multi-slice tomography units, but their values were always below the recommended DRLs. The optimized values of the dosimetric quantities obtained after the optimization process showed that it was possible to reduce the radiation exposure of pediatric patient without losing the image quality

DYNAMIC INVESTIGATION OF THE PURCHASE PRICE AND QUANTITY OF MAIZE AND PIG

Directory of Open Access Journals (Sweden)

Judit POÓR

2007-11-01

Full Text Available The aim of our examination was to show the cyclic character in the case of agricultural prices. Beside the investigation of prices the analysis of the purchased quantity is of importance too. We examined the way the prices and quantity exercise mutual influence and the connection between the maize purchase price and the pig purchase price. We compared the Hungarian purchase prices with some international ones, and analyzed the tendencies, the influence of open economies and the approach of the prices.

A note on the expectation and deviation of physical quantities

International Nuclear Information System (INIS)

Nagasawa, Masao

2009-01-01

By using the function representation of self-adjoint operators, the expectation and variance of physical quantities (self-adjoint operators) are defined, and it is shown that the so-called uncertainty principle does not hold.

Effects of DME pilot quantity on the performance of a DME PCCI-DI engine

International Nuclear Information System (INIS)

Wang Ying; He Li; Zhou Longbao; Li Wei

2010-01-01

The combination of premixed charge compression ignition and conventional direct-injection compression ignition combustion is studied in a DME engine. This combustion mode is referred to as PCCI-DI combustion. The pilot quantity is found to be one of main variables affecting the PCCI-DI combustion. So, the main objectives of this paper are to examine the effect of different DME pilot quantities on combustion and emission characteristics in a single-cylinder direct-injection DME engine and to determine whether PCCI-DI is a viable in-cylinder NO x emissions reduction technology. In order to evaluate the characteristics of PCCI-DI combustion, the conventional direct-injection compression-ignition engine performance is supplied to make a comparison with their results. Furthermore, special emphasis is put upon the combined combustion process analysis. Results show that DME engine can operate at a wide range of speeds and loads at PCCI-DI mode. In comparison to the conventional DME CI combustion, the brake thermal efficiency slightly increases for DME PCCI-DI operation. PCCI-DI is capable to decrease NO x effectively for all loads. NO x emission shows an obviously descending tendency with an increase in DME pilot quantity at low loads, while it shows a mildly elevating tendency with an increase in DME pilot quantity at high loads. HC and CO emissions increase for DME PCCI-DI operation under various DME pilot quantities.

Quality versus Quantity Debate in Swimming: Perceptions and Training Practices of Expert Swimming Coaches.

Science.gov (United States)

Nugent, Frank J; Comyns, Thomas M; Warrington, Giles D

2017-06-01

The debate over low-volume, high-intensity training versus high-volume, low-intensity training, commonly known as Quality versus Quantity, respectively, is a frequent topic of discussion among swimming coaches and academics. The aim of this study was to explore expert coaches' perceptions of quality and quantity coaching philosophies in competitive swimming and to investigate their current training practices. A purposeful sample of 11 expert swimming coaches was recruited for this study. The study was a mixed methods design and involved each coach participating in 1 semi-structured interview and completing 1 closed-ended questionnaire. The main findings of this study were that coaches felt quality training programmes would lead to short term results for youth swimmers, but were in many cases more appropriate for senior swimmers. The coaches suggested that quantity training programmes built an aerobic base for youth swimmers, promoted technical development through a focus on slower swimming and helped to enhance recovery from training or competition. However, the coaches continuously suggested that quantity training programmes must be performed with good technique and they felt this was a misunderstood element. This study was a critical step towards gaining a richer and broader understanding on the debate over Quality versus Quantity training from an expert swimming coaches' perspective which was not currently available in the research literature.

Quality Versus Quantity Debate in Swimming: Perceptions and Training Practices of Expert Swimming Coaches

Directory of Open Access Journals (Sweden)

Nugent Frank J.

2017-06-01

Full Text Available The debate over low-volume, high-intensity training versus high-volume, low-intensity training, commonly known as Quality versus Quantity, respectively, is a frequent topic of discussion among swimming coaches and academics. The aim of this study was to explore expert coaches’ perceptions of quality and quantity coaching philosophies in competitive swimming and to investigate their current training practices. A purposeful sample of 11 expert swimming coaches was recruited for this study. The study was a mixed methods design and involved each coach participating in 1 semi-structured interview and completing 1 closed-ended questionnaire. The main findings of this study were that coaches felt quality training programmes would lead to short term results for youth swimmers, but were in many cases more appropriate for senior swimmers. The coaches suggested that quantity training programmes built an aerobic base for youth swimmers, promoted technical development through a focus on slower swimming and helped to enhance recovery from training or competition. However, the coaches continuously suggested that quantity training programmes must be performed with good technique and they felt this was a misunderstood element. This study was a critical step towards gaining a richer and broader understanding on the debate over Quality versus Quantity training from an expert swimming coaches’ perspective which was not currently available in the research literature.

Results of the regional intercomparison exercise for the determination of operational quantity Hp(d) in Latin America

International Nuclear Information System (INIS)

Saravi, M.; Zaretzky, A.; Lindner, C.; Diaz, J.; Walwyn, G.; Souza, D.; Amorin, R.; Gregory, B.; Papadopulos, S.; Meghzifene, A.; Ferruz Cruz, P.; Cruz Suarez, R.

2005-01-01

Full text: Several intercomparison exercises were organized by the International Atomic Energy Agency (IAEA) on the determination of operational quantities at the regional or interregional basis. These exercises revealed significant differences in the approach, methods and assumptions, and consequently in the measurement results obtained by participating laboratories. In the Latin America region, an intercomparison for determination of operational quantity Hp(10), organized within the frame of a technical cooperation regional project, was completed mid-2004, as a follow-up to previous exercises carried out during the 1990s. Eighteen laboratories from 19 member states participated in the first phase; the second phase grouped 15 laboratories from 16 member states. Dosimeter irradiations (5 different radiation qualities for photon simulating workplace fields) were done by 4 Secondary Standards Dosimetry Laboratories (SSDL). The preparations for the exercise involved an audit by the IAEA SSDL, where reference irradiations were provided to all participants for verification of their system. During the first phase (2002/03), only 9 out of 18 laboratories met the performance requirements for such monitoring services. Necessary corrective actions and procedure verification were implemented, and staff involved in these evaluations were subsequently trained. During the second phase (2004), 11 out of 15 laboratories fulfilled the performance criteria. The 4 laboratories still having difficulties in assessing occupational exposure participated in a results meeting, during which problem areas were identified. An ongoing technical cooperation mission is expected to assist these laboratories accordingly. There has been a definite improvement in the second phase and most laboratories demonstrated a good performance in the quantity tested. The technical results clearly show that the laboratories' capability in assessing occupational exposure from external sources of radiation is

The Hazardous Drinking Games Measure (HDGM): A multi-site implementation

Science.gov (United States)

Borsari, Brian; Peterson, Colleen; Zamboanga, Byron L.; Correia, Christopher J.; Olthuis, Janine V.; Ham, Lindsay S.; Grossbard, Joel

2014-01-01

Background Drinking game participation has been associated with increased frequency and quantity of alcohol use, as well as alcohol-related problems, in college students. To date, the assessment of drinking games typically entails the use of self-developed measures of frequency of participation and amount of alcohol consumed while playing. Objectives The Hazardous Drinking Games Measure (HDGM) is the first effort to create a comprehensive yet concise method of assessing drinking game participation. The HDGM assesses drinking during games, the specific types of drinking games played, and negative consequences experienced as a result of playing drinking games. Method Data from three samples of college students (n = 1002) who completed the HDGM and other self-report questionnaires of drinking behaviors were used for exploratory analyses. Results Exploratory analyses suggest that the HDGM adequately captures the nuances of drinking game participation in this population and demonstrates initial evidence of good content and criterion-related validity and test-retest reliability. However, the HDGM did not predict risky drinking above and beyond standard measures of drinks per week and alcohol-related problems in any samples. Conclusion The HDGM may be useful for campus-wide assessment of drinking games and as a source of game-specific feedback when integrated into campus prevention and intervention efforts. PMID:25192208

Role of Leadership in Transforming the Profession of Quantity Surveying

Directory of Open Access Journals (Sweden)

George Ofori

2012-11-01

Full Text Available The construction industry is facing a period of change. The roles ofthe professions involved in the industry in general, and of quantitysurveyors in particular, are also changing. There are opportunitiesfor surveyors to seize the initiative to broaden their involvement inprojects, and attain strategic positions within the industry. However,they will have to improve upon their skill sets and their knowledgebases. Senior quantity surveyors interviewed in Singapore sharedtheir views on the challenges facing the construction industry,and their profession. They suggested that the quantity surveyingprofession would only be able to address the pressing issues itfaces if it pays more attention to innovation and the development ofits people. It should be able to attract and retain talent. Knowledgemanagement will be of critical importance. This will be enabled andfacilitated by knowledge leadership.

19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

Solvation quantities from a COSMO-RS equation of state

International Nuclear Information System (INIS)

Panayiotou, C.; Tsivintzelis, I.; Aslanidou, D.; Hatzimanikatis, V.

2015-01-01

Highlights: • Extension of the successful COSMO-RS model to an equation-of-state model. • Two scaling constants, obtained from atom-specific contributions. • Overall estimation of the solvation quantities and contributions. - Abstract: This work focuses on the extension of the successful COSMO-RS model of mixtures into an equation-of-state model of fluids and its application for the estimation of solvation/hydration quantities of a variety of chemical substances. These quantities include free-energies, enthalpies and entropies of hydration as well as the separate contributions to each of them. Emphasis is given on the estimation of contributions from the conformational changes of solutes upon solvation and the associated restructuring of solvent in its immediate neighborhood. COSMO-RS is a quantum-mechanics based group/segment contribution model in which the Quasi-Chemical (QC) approach is used for the description of the non-random distribution of interacting segments in the system. Thus, the equation-of-state development is done through such a QC framework. The new model will not need any adjustable parameters for the strong specific interactions, such as hydrogen bonds, since they will be provided by the quantum-mechanics based cosmo-files – a key feature of COSMO-RS model. It will need, however, one volumetric and one energy parameter per fluid, which are scaling constants or molecular descriptors of the fluid and are obtained from rather easily available data such as densities, boiling points, vapor pressures, heats of vaporization or second virial coefficients. The performance and the potential of the new equation-of-state model to become a fully predictive model are critically discussed

Alternate measurements of benefit to criticality issues at Hanford

Energy Technology Data Exchange (ETDEWEB)

Toffer, H.; Cabrilla, D.E.

1997-06-01

Measurements in a critical mass facility, such as the Los Alamos Critical Experiments Facility, could be performed on simulated nuclear waste materials that would provide important critical mass information and concurrently provide a calibration of alternate measurement techniques. In addition to criticality information, the measurements could also provide a better assessment of diluent material/neutron interaction cross sections. An Hanford, large quantities of fissionable materials are dispersed in tanks, fuel storage pools, and in solid waste. Although the fissionable materials are well diluted by a variety of neutron-moderating and -absorbing substances, it is difficult to assess the margin of subcriticality. A number of measurement approaches are proposed that will either help determine fissionable material concentrations, distributions, or provide a direct measure of subcriticality. The methods under consideration involve passive neutron counting, active neutron measurements, pulse neutron applications, neutron noise analyses, and cover gas evaluations. Active neutron measurements can also provide insight into the determination of neutron absorber concentrations. Efforts are underway to test some of the methods in actual waste tank environments and geometries. It is important that these methods be tested and calibrated in a critical mass facility.

Alternate measurements of benefit to criticality issues at Hanford

International Nuclear Information System (INIS)

Toffer, H.; Cabrilla, D.E.

1997-01-01

Measurements in a critical mass facility, such as the Los Alamos Critical Experiments Facility, could be performed on simulated nuclear waste materials that would provide important critical mass information and concurrently provide a calibration of alternate measurement techniques. In addition to criticality information, the measurements could also provide a better assessment of diluent material/neutron interaction cross sections. An Hanford, large quantities of fissionable materials are dispersed in tanks, fuel storage pools, and in solid waste. Although the fissionable materials are well diluted by a variety of neutron-moderating and -absorbing substances, it is difficult to assess the margin of subcriticality. A number of measurement approaches are proposed that will either help determine fissionable material concentrations, distributions, or provide a direct measure of subcriticality. The methods under consideration involve passive neutron counting, active neutron measurements, pulse neutron applications, neutron noise analyses, and cover gas evaluations. Active neutron measurements can also provide insight into the determination of neutron absorber concentrations. Efforts are underway to test some of the methods in actual waste tank environments and geometries. It is important that these methods be tested and calibrated in a critical mass facility

MICROMICETES QUANTITY AND BIOMASS IN TECHNOGENIC AND NATURAL SOILS

Directory of Open Access Journals (Sweden)

O. N. Korinovskaya

2014-08-01

Full Text Available It is shown that in edaphotopes around of freight checkpoint of CJSC «Krivorozhskiy Surikovyy Zavod», ore-enrichment factory and fresh-inwashed pool of tailings dam of PJSC «Northern Iron Ore Enrichment Works» there is an increase of heavy metals mobile forms (which are the most dangerous for microorganisms, plants, animals and human: for iron in 310; for zinc - in 4,3-6,5; for lead - in 3.2-5.7; for cadmium - in 5,6-9,8; for copper – 6,8-66,5 and for nickel - in 9 times as compared to zonal soil. Whereas in soils of CJSC «Krivorozhskiy Surikovyy Zavod» sanitary protection zone number of copper, nickel, lead, cadmium and zinc mobile forms exceeded the control values in 2,4-6,6 times. For the first time the features of soil microscopic fungi seasonal dynamics of quantity in industrial disturbed soils of Kryvorizhzhya compared to zonal soil (chernozem usual were registered. Changes in fungal mycelium length and biomass, its spore’s amount and biomass in edaphotopes of ore-enrichment and chemical enterprises and of common chernozem are also presented. It is shown that in edaphotopes of heavy contamination areas of «Krivorozhskiy Surikovyy Zavod» and of «Northern Iron Ore Enrichment Works» in spring, summer, and autumn there was decrease of microscopic fungi quantity in 4-10 times, moreover in tehnozems of «Northern Iron Ore Enrichment Works» fresh-inwashed pool of tailings dam their amount reduces in more than 100 times, compared with common chernozem. In low contamination area of «Krivorozhskiy Surikovyy Zavod» their quantity decreases in 2 times. Also in heavy contamination areas of chemical and ore-enrichment enterprises there is strong decrease in the length of fungal mycelium in 2.7-4.2 times, its biomass in 2,6-4,5 times, the spores amount - in 4,5-7,7 times and their biomass - in 10,5-21 times compared to the natural soil, which could be explained by high contents of toxicants. While in the sanitary protection zone of the �

Comparison of different uncertainty techniques in urban stormwater quantity and quality modelling

DEFF Research Database (Denmark)

Dotto, C. B.; Mannina, G.; Kleidorfer, M.

2012-01-01

-UA), an approach based on a multi-objective auto-calibration (a multialgorithm, genetically adaptive multiobjective method, AMALGAM) and a Bayesian approach based on a simplified Markov Chain Monte Carlo method (implemented in the software MICA). To allow a meaningful comparison among the different uncertainty...... techniques, common criteria have been set for the likelihood formulation, defining the number of simulations, and the measure of uncertainty bounds. Moreover, all the uncertainty techniques were implemented for the same case study, in which the same stormwater quantity and quality model was used alongside...... the same dataset. The comparison results for a well-posed rainfall/runoff model showed that the four methods provide similar probability distributions of model parameters, and model prediction intervals. For ill-posed water quality model the differences between the results were much wider; and the paper...

Clarification of the confusion concerning the crystal-field quantities vs the zero-field splitting quantities in magnetism studies: Part II-Survey of literature dealing with model studies of spin systems

International Nuclear Information System (INIS)

Rudowicz, C.

2008-01-01

For respective quantities, i.e., Hamiltonians, parameters, and energy level splittings, related to two physically distinct notions X and Y, various cases of confused terminology have been identified in literature. Referring to a quantity related actually to the notion Y using incorrectly the name of another well-defined notion X constitutes, what may be defined for short as, the type X=Y confusion. An ongoing survey of magnetism literature indicates that quantities related to zero-field splitting (ZFS) or equivalently fine structure (FS) are most often confused with those related to crystal-field (CF) or equivalently ligand field (LF). In this review the CF=ZFS confusion cases, i.e., labelling actual ZFS/FS quantities as purportedly 'CF/LF' ones, appearing in magnetism studies are surveyed and clarified. Part I covers the cases occurring in literature dealing with specific compounds. In this part model studies of spin systems are surveyed. The cases of terminology mixing up actual ZFS/FS quantities with purported CF/LF ones are identified and presented comprehensively in tabular form. To facilitate discussion, problems pertinent for the CF=ZFS confusion are categorized into several groups, including origin of the two notions, physical consequences, usage of specific numerical values, invoking real magnetic spin systems, and properties of spin S=1/2 systems. Physical implications of this confusion for interpretation of model results are also considered. Overall implications of incorrect terminology go beyond simple semantic issues and concern possible misinterpretation of data describing various physical properties of models studied. Such terminology contributes also to misleading keyword classifications of papers in journals and scientific databases. Other types of confusion identified in survey of magnetism literature will be discussed in separate reviews

Is the Quantity Theory of Money Useful in Forecasting U.S. Inflation?

DEFF Research Database (Denmark)

Lanne, Markku; Luoto, Jani; Nyberg, Henri

We propose a new simple model incorporating the implication of the quantity theory of money that money growth and ináation should move one for one in the long run, and, hence, ináation should be predictable by money growth. The model Öts postwar U.S. data well, and beats common univariate benchma...... models in forecasting ináation. Moreover, this evidence is quite robust, and predictability is found also in the Great moderation period. The detected predictability of ináation by money growth lends support to the quantity theory....

Teacher quality and quantity as correlates of secondary school ...

African Journals Online (AJOL)

This study investigated the twin variables of quality and quantity of teachers as correlates of secondary school academic performance in Ogun State of Nigeria between 1997/98 and 2000/2001 academic sessions. The study was conducted ex-post facto under a descriptive survey research design using the proportional to ...

Water quantity and quality at the urban-rural interface

Science.gov (United States)

Ge Sun; B. Graeme Lockaby

2012-01-01

Population growth and urban development dramatically alter natural watershed ecosystem structure and functions and stress water resources. We review studies on the impacts of urbanization on hydrologic and biogeochemical processes underlying stream water quantity and water quality issues, as well as water supply challenges in an urban environment. We conclude that...

Resource rents: The effects of energy taxes and quantity instruments for climate protection

International Nuclear Information System (INIS)

Eisenack, Klaus; Edenhofer, Ottmar; Kalkuhl, Matthias

2012-01-01

Carbon dioxide emissions correspond to fossil resource use. When considering this supply side of climate protection, crucial questions come to fore. It seems likely that owners of fossil resources would object to emission reductions. Moreover, policy instruments such as taxes may not be effective at all: it seems individually rational to leave no fossil resources unused. In this context, it can be expected that economic sectors will react strategically to climate policy, aiming at a re-distribution of rents. To address these questions, we investigate the effectiveness, efficiency, and resource rents for energy taxes, resource taxes, and quantity rationing of emissions. The analysis is based on a game theoretic growth model with explicit factor markets and policy instruments. Market equilibrium depends on a government that acts as a Stackelberg leader with a climate protection goal. We find that resource taxes and quantity rationing achieve this objective efficiently, energy taxation is only second-best. The use of quantity rationing to achieve climate protection generates substantial rents for resource owners. - Highlights: ► Resource taxes and quantity rationing (carbon budgets) are efficient. ► Carbon budgets increase resource rents, while taxes decrease rents. ► Resource owners may support climate protection. ► Climate protection introduces a climate rent.

Supply Chain Coordination under Trade Credit and Quantity Discount with Sales Effort Effects

Directory of Open Access Journals (Sweden)

Zhihong Wang

2018-01-01

Full Text Available The purpose of this paper is to investigate the role of trade credit and quantity discount in supply chain coordination when the sales effort effect on market demand is considered. In this paper, we consider a two-echelon supply chain consisting of a single retailer ordering a single product from a single manufacturer. Market demand is stochastic and is influenced by retailer sales effort. We formulate an analytical model based on a single trade credit and find that the single trade credit cannot achieve the perfect coordination of the supply chain. Then, we develop a hybrid quantitative analytical model for supply chain coordination by coherently integrating incentives of trade credit and quantity discount with sales effort effects. The results demonstrate that, providing that the discount rate satisfies certain conditions, the proposed hybrid model combining trade credit and quantity discount will be able to effectively coordinate the supply chain by motivating retailers to exert their sales effort and increase product order quantity. Furthermore, the hybrid quantitative analytical model can provide great flexibility in coordinating the supply chain to achieve an optimal situation through the adjustment of relevant parameters to resolve conflict of interests from different supply chain members. Numerical examples are provided to demonstrate the effectiveness of the hybrid model.

Analyse of Maintenance Cost in ST

CERN Document Server

Jenssen, B W

2001-01-01

An analyse has been carried out in ST concerning the total costs for the division. Even though the target was the maintenance costs in ST, the global budget over has been analysed. This has been done since there is close relation between investments & consolidation and the required level for maintenance. The purpose of the analyse was to focus on maintenance cost in ST as a ratio of total maintenance costs over the replacement value of the equipment, and to make some comparisons with other industries and laboratories. Families of equipment have been defined and their corresponding ratios calculated. This first approach gives us some "quantitative" measurements. This analyse should be combined with performance indicators (more "qualitative" measurements) that are telling us how well we are performing. This will help us in defending our budget, make better priorities, and we will satisfy the requirements from our external auditors.

Thermodynamical analyses of molecular simulations of dislocation-defect interactions: simulations at 0 K

International Nuclear Information System (INIS)

Monnet, G.

2008-01-01

Full text of publication follows. Static molecular (SM) simulations of dislocation-defect interaction are analysed through a framework of different interaction regimes, in which the applied work has different roles. In most regimes, the applied work is transformed into elastic energy, a dissipative energy resulting from the lattice friction and a large quantity of energy needed to enable the dislocation to bow out when it is pinned by the defect. While the dissipative work is entirely evacuated in SM simulations, the elastic and curvature energies contribute to a large increase of the internal energy of the system. A method is presented in this work to evaluate the curvature energy and the result is compared to prediction of the line tension model. These analyses allow the determination of the dislocation-defect interaction energy. (author)

Innovative measurement for injection systems; Innovative Messtechnik fuer Einspritzsysteme

Energy Technology Data Exchange (ETDEWEB)

Janetzky, Bjoern; Majer, Clemens; Doell, Reinahrd [Robert Bosch GmbH, Stuttgart (Germany)

2011-07-01

The treatise introduces a new measuring method to determine the injection quantity and injection rate. In this method the change in pressure within a hydraulic chamber is measured during injection. Also the momentary pressure-dependent speed of sound of the medium inside the chamber is measured. With this information the desired injection quantity can be derived with high precision. A measuring technique (HDA) based on this method is described. Measurement with HDA are performed based on actual requirements from the Diesel-Injection-System, results from these measurements are presented in example. Results are compared with those achieved by using a known measuring technique (EMI). (orig.)

Discovery of a new strain of murine rotavirus that is consistently shed in large quantities after oral inoculation of adult mice

International Nuclear Information System (INIS)

McNeal, Monica M.; Belli, Janine; Basu, Mitali; Choi, Anthony H.-C.; Ward, Richard L.

2004-01-01

In 1990, we developed the adult mouse model for studies on active immunity against shedding of the EDIM strain of murine rotavirus. Low and inconsistent levels of EDIM shedding in some strains of adult mice, particularly those on C57BL/6 backgrounds, established the need for an alternative murine rotavirus strain for these studies. Fortuitously, such a rotavirus strain was obtained from mice housed within the conventional colony at Children's Hospital. This strain, named EMcN, was clearly distinguishable from EDIM based on electropherotype. Furthermore, sequence analyses of VP4 and VP7 genes of EMcN revealed non-identities in 5% of the amino acids of both proteins relative to EDIM but established EMcN as another G3P[16] strain of murine rotavirus. Subgroup analysis showed EMcN belonged to SG1 while EDIM was found to be non-SG1/SG2. Similarly, unlike EDIM, the EMcN strain was identified as serotype G3 based on neutralization by hyperimmune antisera developed against prototype human and simian G3 rotavirus strains. Although EDIM produced more days of diarrhea and was shed in greater quantities in neonatal BALB/c mice, EMcN was shed in much greater quantities in adult BALB/c mice. More importantly, in contrast to the EDIM strain, EMcN was shown to be consistently shed in large quantities in adult C57BL/6 mice and ko mice on this background. Therefore, it is recommended that the EMcN strain be used for future challenge studies with mice on this background

Study of the production mechanism of the η meson in proton-proton collisions by means of analysing power measurements

International Nuclear Information System (INIS)

Czyzykiewicz, R.

2007-02-01

The analysing power measurements for the #vector#pp→ppη reaction studied in this dissertation are used in the determination of the reaction mechanism of the η meson production in nucleon-nucleon collisions. Measurements have been performed in the close-to-threshold energy region at beam momenta of p beam =2.010 and 2.085 GeV/c, corresponding to the excess energies of Q=10 and 36 MeV, respectively. The experiments were realised by means of a cooler synchrotron and storage ring COSY along with a cluster jet target. For registration of the reaction products the COSY-11 facility has been used. The identification of the η meson has been performed with the missing mass method. The results for the angular dependence of the analysing power combined with the hitherto determined isospin dependence of the total cross section for the η meson production in the nucleon-nucleon collisions, reveal a statistically significant indication that the excitation of the nucleon to the S 11 resonance, the process which intermediates the production of the η meson, is predominantly due to the exchange of a π meson between the colliding nucleons. The determined values of the analysing power at both excess energies are consistent with zero implying that the η meson is produced predominantly in the s-wave at both excess energies. (orig.)

Notes on the apparent discordance of pulse oximetry and multi-wavelength haemoglobin photometry

NARCIS (Netherlands)

Nijland, R.; Jongsma, H.W.; Nijhuis, J.G.; Oeseburg, Berend; Zijlstra, Willem

1995-01-01

Multi-wavelength photometers, blood gas analysers and pulse oximeters are widely used to measure various oxygen-related quantities. The definitions of these quantities are not always correct. This paper gives insight in the various definitions for oxygen quantities. Furthermore, the possible

IDMS analysis of blank swipe samples for uranium quantity and isotopic composition

International Nuclear Information System (INIS)

Ryjinski, M.; Donohue, D.

2001-01-01

Since 1996 the IAEA has started routine implementation of environmental sampling. During the last 5 years more than 1700 swipe samples were collected and analyzed in the Network of Analytical Laboratories (NWAL). One sensitive point of analyzing environmental samples is evidence of the presence of enriched U. The U content on swipes is extremely low and therefore there is a relatively high probability of a false positive, e.g. small contamination or a measurement bias. In order to avoid and/or control this the IAEA systematically sends to the laboratories blind blank QC samples. In particular more than 50 blank samples were analyzed during the last two years. A preliminary analysis of blank swipes showed the swipe material itself contains up to 10 ng of NU per swipe. However, about 50% of blind blank swipes analyzed show the presence of enriched uranium. A source of this bias has to be clarified and excluded. This paper presents the results of modeling of IDMS analysis for quantity and isotopic composition of uranium in order to identify the possible contribution of different factors to the final measurement uncertainty. This modeling was carried out based on the IAEA Clean Laboratory measurement data and simulation technique

Thermodynamic quantities for the Klein–Gordon equation with a ...

Indian Academy of Sciences (India)

2017-02-01

Feb 1, 2017 ... Abstract. We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverse- linear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation. We use a method based on the Euler–MacLaurin formula to ...

On the operational quantity Hp(3) for eye lens dosimetry

International Nuclear Information System (INIS)

Behrens, R

2012-01-01

In the past the operational quantity H p (3) has been defined for calibration purposes in a slab phantom. Recently, an additional phantom in the form of a cylinder was suggested for eye lens dosimetry as a cylinder much better approximates the shape of a head than a slab. Therefore, this work investigates whether the quantity H p (3), when defined in the respective calibration phantom, adequately estimates the eye lens dose (or is at least conservative) depending on the phantom: it turns out that in most cases both calibration phantoms are similarly well suited. Finally, the definition of the eye lens dose is discussed together with possible consequences on the definition of H p (3): the consideration of only the radiation sensitive volume of the lens causes H p (3) not to be conservative in beta radiation fields. (paper)

The moderating effects of peer substance use on the family structure-adolescent substance use association: quantity versus quality of parenting.

Science.gov (United States)

Eitle, David

2005-06-01

This study examines the association between family structure and adolescent substance use, specifically focusing on the potential conditioning effects of the level of exposure to substance-using peers. Using data from a statewide study of Florida students, tobacco, alcohol, marijuana, and other illicit drug use was regressed on measures of family structure, exposure to deviant peers, family process variables (including supervision, attachment, and discipline), and an array of salient predictors of adolescent substance use. Logistic regression analyses revealed that the level of exposure to substance-using peers moderates the relationship between family structure and substance use for three of the four dependent variables. The core finding is that living with two natural parents serves as a protective factor against using tobacco, alcohol, or other illicit drugs, but only under conditions when exposure to deviant peers is lowest. Under conditions when exposure to deviant peers is highest, teens residing in a traditional two-parent family are most likely to report substance use. However, some evidence suggests that this latter finding may be due to differences in the duration of exposure to deviant peers. These findings reinforce the need to continue to explore how the quantity of parenting may provide additional protection against adolescent substance use beyond quality of parenting factors.

IRE (Institut National des Radioelements) site in Belgium. Report of in situ measurements and analyses performed for the RTBF; Site IRE (Institut National des Radioelements) en Belgique. Compte rendu des mesures in situ et analyses effectuees pour la RTBF

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-05-15

This document reports various analyses performed within the frame of the preparation and filming of a TV documentary on the Belgium National Institute of Radio-elements. It reports gamma radiation measurements performed at the vicinity of the institute, discusses the possible origin of its increase at the vicinity of the institute, analyses of sludge samples coming from a wastewater treatment works, and analyses of milk, cabbage, mosses and sediments collected by residents

Nuclear energy - Reference beta-particle radiation - Part 2: Calibration fundamentals related to basic quantities characterizing the radiation field

International Nuclear Information System (INIS)

2004-01-01

ISO 6980 consists of the following parts, under the general title Nuclear energy - Reference beta-particle radiation: Part 1: Method of production; Part 2: Calibration fundamentals related to basic quantities characterizing the radiation field; Part 3: Calibration of area and personal dosimeters and determination of their response as a function of energy and angle of incidence. This part 2 of ISO 6980 specifies methods for the measurement of the directional absorbed-dose rate in a tissue-equivalent slab phantom in the ISO 6980 reference beta-particle radiation fields. The energy range of the beta-particle-emitting isotopes covered by these reference radiations is 0.066 to 3.54 MeV (maximum energy). Radiation energies outside this range are beyond the scope of this standard. While measurements in a reference geometry (depth of 0.07 mm at perpendicular incidence in a tissue-equivalent slab phantom) with a reference class extrapolation chamber are dealt with in detail, the use of other measurement systems and measurements in other geometries are also described, although in less detail. The ambient dose equivalent, H*(10) as used for area monitoring of strongly penetrating radiation, is not an appropriate quantity for any beta radiation, even for that penetrating a 10 mm thick layer of ICRU tissue (i.e. E max > 2 MeV). If adequate protection is provided at 0.07 mm, only rarely will one be concerned with other depths, for example 3 mm. This document is geared towards organizations wishing to establish reference-class dosimetry capabilities for beta particles, and serves as a guide to the performance of dosimetry with the reference class extrapolation chamber for beta-particle dosimetry in other fields. Guidance is also provided on the statement of measurement uncertainties

Buyer-vendor coordination for fixed lifetime product with quantity discount under finite production rate

Science.gov (United States)

Zhang, Qinghong; Luo, Jianwen; Duan, Yongrui

2016-03-01

Buyer-vendor coordination has been widely addressed; however, the fixed lifetime of the product is seldom considered. In this paper, we study the coordination of an integrated production-inventory system with quantity discount for a fixed lifetime product under finite production rate and deterministic demand. We first derive the buyer's ordering policy and the vendor's production batch size in decentralised and centralised systems. We then compare the two systems and show the non-coordination of the ordering policies and the production batch sizes. To improve the supply chain efficiency, we propose quantity discount contract and prove that the contract can coordinate the buyer-vendor supply chain. Finally, we present analytically tractable solutions and give a numerical example to illustrate the benefits of the proposed quantity discount strategy.

Analysis on Domestic Law and Management Trend Related to Small-Quantity Nuclear Material

International Nuclear Information System (INIS)

Park, Jae Beom; Lee, Kyong Woo; Shim, Hye Won; Min, Gyung Sik

2005-01-01

International Atomic Energy Agency (IAEA) has requested Korea to establish and manage the law ruling all nuclear materials through the INFCIRC/153. Now, it has been 30 years since Korea made the agreement, INFCIRC/153, with IAEA. Korea has tried their best to accomplish the international standard in nuclear control field and it is a fact that Korea finally produced some results in the nuclear control field. Related to nuclear material control, Korea is above the common level appropriately ranked 6th in the world in terms of nuclear power. Before 2000, Korea was making the foundation secure in the nuclear control. IAEA did not urge to establish the law supervising the small-quantity nuclear material and depleted uranium (DU). In a turnaround from early IAEA moderate line to Korea, the situation was changed. Since IAEA brought up the agenda to 2000 Joint Review Meeting between Korea-IAEA, IAEA has asked Korea to establish the control system for smallquantity nuclear material and DU. In 2003, the Korean government set up a project establishing the control system about all nuclear material including small-quantity nuclear material and DU. National Nuclear Management and Control Agency (NNCA), delegating the business relating to international controlling materials from government, developed some modules in nuclear material control system and operated it. The system includes a controlling system for small-quantity nuclear material. NNCA on behalf of government has collected the information and Korea Ministry of Science and Technology (MOST) has reported the information to the IAEA. This paper introduces you the background of controlling the small-quantity nuclear material and the system of controlling nuclear material in Korea. And it will suggest the improvement of the management method in the system for small-quantity nuclear material

Analysis on Domestic Law and Management Trend Related to Small-Quantity Nuclear Material

Energy Technology Data Exchange (ETDEWEB)

Park, Jae Beom; Lee, Kyong Woo; Shim, Hye Won; Min, Gyung Sik [National Nuclear Management and Control Agency, Daejeon (Korea, Republic of)

2005-07-01

International Atomic Energy Agency (IAEA) has requested Korea to establish and manage the law ruling all nuclear materials through the INFCIRC/153. Now, it has been 30 years since Korea made the agreement, INFCIRC/153, with IAEA. Korea has tried their best to accomplish the international standard in nuclear control field and it is a fact that Korea finally produced some results in the nuclear control field. Related to nuclear material control, Korea is above the common level appropriately ranked 6th in the world in terms of nuclear power. Before 2000, Korea was making the foundation secure in the nuclear control. IAEA did not urge to establish the law supervising the small-quantity nuclear material and depleted uranium (DU). In a turnaround from early IAEA moderate line to Korea, the situation was changed. Since IAEA brought up the agenda to 2000 Joint Review Meeting between Korea-IAEA, IAEA has asked Korea to establish the control system for smallquantity nuclear material and DU. In 2003, the Korean government set up a project establishing the control system about all nuclear material including small-quantity nuclear material and DU. National Nuclear Management and Control Agency (NNCA), delegating the business relating to international controlling materials from government, developed some modules in nuclear material control system and operated it. The system includes a controlling system for small-quantity nuclear material. NNCA on behalf of government has collected the information and Korea Ministry of Science and Technology (MOST) has reported the information to the IAEA. This paper introduces you the background of controlling the small-quantity nuclear material and the system of controlling nuclear material in Korea. And it will suggest the improvement of the management method in the system for small-quantity nuclear material.

Highway route controlled quantity shipment routing reports - An overview

International Nuclear Information System (INIS)

Cashwell, J.W.; Welles, B.W.; Welch, M.J.

1989-01-01

US Department of Transportation (DOT) regulations require a postnotification report from the shipper for all shipments of radioactive materials categorized as a Highway Route Controlled Quantity. These postnotification reports, filed in compliance with 49 CFR 172.203(d), have been compiled by the DOT in a database known as the Radioactive Materials Routing Report (RAMRT) since 1982. The data were sorted by each of its elements to establish historical records and trends of Highway Route Controlled Quantity shipments from 1982 through 1987. Approximately 1520 records in the RAMRT database were compiled for this analysis. Approximately half of the shipments reported for the study period were from the US Department of Energy (DOE) and its contractors, with the others being commercial movements. Two DOE installations, EG and G Idaho and Oak Ridge, accounted for nearly half of the DOE activities. Similarly, almost half of the commercial movements were reported by two vendors, Nuclear Assurance Corporation and Transnuclear, Incorporated. Spent fuel from power and research reactors accounted for approximately half of all shipments

The Citizen Observatory of Radioactivity - Assessment of results - Measurement of gamma emitters. Year 2009

International Nuclear Information System (INIS)

2010-01-01

This document proposes a set of tables containing different information and data regarding measurements of gamma radioactivity made during the first and second half-year of 2009 in different marine and water environments (algae, sands, sea water, molluscs, sediments, water mosses, vegetal) in different locations: a bay close to the AREVA plant in La Hague, different locations on the Normandy coast, around the AREVA plant in La Hague, waterways in Normandy and in other river near the Chinon and Civaux nuclear power stations. These tables contain information about the sampling (date, location, quantity, analysed fraction, and so on) and results of measurements of artificial (isotopes of cobalt, ruthenium-rhodium, silver, iodine, caesium, americium, europium) and natural (potassium, beryllium, lead, bismuth, etc.) radionuclides

Accurate Measurement of Pasting Temperature by the Rapid Visco-Analyser: a Case Study Using Rice Flour

Directory of Open Access Journals (Sweden)

Jin-song BAO

2008-03-01

Full Text Available Pasting properties are among the most important characteristics of starch, determining its applications in food processing and other industries. Pasting temperature derived from the Rapid Visco-analyser (RVA (Newport Scientific, in most cases, is overestimated by the Thermocline for Windows software program. Here, two methods facilitating accurate measurement of pasting temperature by RVA were described. One is to change parameter setting to ‘screen’ the true point where the pasting viscosity begins to increase, the other is to manually record the time (T1 when the pasting viscosity begins to increase and calculate the pasting temperature with the formula of (45/3.8×(T1–1+50 for rice flour. The latter method gave a manually determined pasting temperature which was significantly correlated with the gelatinization temperature measured by differential scanning calorimetry.

Comparison of elastic and inelastic analyses

International Nuclear Information System (INIS)

Ammerman, D.J.; Heinstein, M.W.; Wellman, G.W.

1992-01-01

The use of inelastic analysis methods instead of the traditional elastic analysis methods in the design of radioactive material (RAM) transport packagings leads to a better understanding of the response of the package to mechanical loadings. Thus, better assessment of the containment, thermal protection, and shielding integrity of the package after a structure accident event can be made. A more accurate prediction of the package response can lead to enhanced safety and also allow for a more efficient use of materials, possibly leading to a package with higher capacity or lower weight. This paper discusses the advantages and disadvantages of using inelastic analysis in the design of RAM shipping packages. The use of inelastic analysis presents several problems to the package designer. When using inelastic analysis the entire nonlinear response of the material must be known, including the effects of temperature changes and strain rate. Another problem is that there currently is not an acceptance criteria for this type of analysis that is approved by regulatory agencies. Inelastic analysis acceptance criteria based on failure stress, failure strain , or plastic energy density could be developed. For both elastic and inelastic analyses it is also important to include other sources of stress in the analyses, such as fabrication stresses, thermal stresses, stresses from bolt preloading, and contact stresses at material interfaces. Offsetting these added difficulties is the improved knowledge of the package behavior. This allows for incorporation of a more uniform margin of safety, which can result in weight savings and a higher level of confidence in the post-accident configuration of the package. In this paper, comparisons between elastic and inelastic analyses are made for a simple ring structure and for a package to transport a large quantity of RAM by rail (rail cask) with lead gamma shielding to illustrate the differences in the two analysis techniques

Dimensions of Organisational Culture in Quantity Surveying Firms in Nigeria

Directory of Open Access Journals (Sweden)

Ayokunle Olubunmi Olanipekun

2014-12-01

Full Text Available The functionalist paradigm of organisational culture (OC views culture as a variable subject to conscious manipulation and control in order to solve organisational challenges. Therefore, this paper provides information on how OC is a solution to the challenges in Quantity Surveying firms (QSFs.  This was achieved by eliciting the dimensions of OC in forty two QSFs in Lagos, Nigeria, which are the business, people and external environment dimensions. The paper concludes that OC is a relevant solution to the identity and management related challenges in QSFs. Specifically, the paper informs on the implications of business and people dimensions of OC as a solution to the identity challenges, as well as on the implication of the external environment dimension of OC to the management challenges. Based on the findings, practical implications and recommendations were directed at the management and employees QSs in QSFs and Quantity Surveying researchers.

Test of ring, eye lens and whole body dosemeters for the dose quantity Hp(3) to be used in interventional radiology

Science.gov (United States)

Szumska, A.; Budzanowski, M.; Kopeć, R.

2017-11-01

In its statement on tissue reactions approved on 21st April 2011, the International Commission on Radiological Protection (ICRP, 2012) reviewed its recommendation concerning the equivalent dose limit for the eye lens and reduced the dose limits for occupationally exposed persons to 20 mSv in a year, averaged over defined periods of 5 years, with no single year exceeding 50 mSv. This limit was approved and written down in the new EURATOM (European Atomic Energy Community) directive 2013/59 and in the IAEA (International Atomic Energy Agency) BSS (Basic Safety Standard) of July 2014. For that reason, the necessity to monitor the eye lens may become more important than it was before. However, specially dedicated dosemeters for the dose quantity Hp(3) are using very rarely. Commonly use are only whole body personal dosemeters for the personal dose equivalent quantities Hp(10) worn on the trunk and ring dosemeters worn on finger to measure the quantity Hp(0.07). Therefore, in this work it was investigated whether dosemeters from routine use calibrated in terms of Hp(10) and Hp(0.07) and worn on thyroid collar and protective apron could deliver similar results like dedicated eye lens dosemeter worn close to the eyes. The results show that the best method if dedicated eye lens dosimeters is not used is to measure doses in terms of Hp(0.07) on the thyroid collar (Pearson product, r=0.85). Obtained results shows also importance of proper localization of eye lens dosimeter (close to the eye, from side of the X-ray source).

Ethical analyses of institutional measures to increase health care worker influenza vaccination rates.

Science.gov (United States)

Zimmerman, Richard K

2013-12-16

Health care worker (HCW) influenza vaccination rates are modest. This paper provides a detailed ethical analysis of the major options to increase HCW vaccination rates, comparing how major ethical theories would address the options. The main categories of interventions to raise rates include education, incentives, easy access, competition with rewards, assessment and feedback, declination, mandates with alternative infection control measures, and mandates with administrative action as consequences. The aforementioned interventions, except mandates, arouse little ethical controversy. However, these efforts are time and work intensive and rarely achieve vaccination rates higher than about 70%. The primary concerns voiced about mandates are loss of autonomy, injustice, lack of due process, and subsuming the individual for institutional ends. Proponents of mandates argue that they are ethical based on beneficence, non-maleficence, and duty. A number of professional associations support mandates. Arguments by analogy can be made by mandates for HCW vaccination against other diseases. The ethical systems used in the analyses include evolutionary ethics, utilitarianism, principalism (autonomy, beneficence, non-maleficence, and justice), Kantism, and altruism. Across these systems, the most commonly preferred options are easy access, assessment and feedback, declinations, and mandates with infection control measures as consequences for non-compliance. Given the ethical imperatives of non-maleficence and beneficence, the limited success of lower intensive interventions, and the need for putting patient safety ahead of HCW convenience, mandates with additional infection control measures as consequences for non-compliance are preferred. For those who opt out of vaccination due to conscience concerns, such mandates provide a means to remain employed but not put patient safety at risk. Copyright © 2013 Elsevier Ltd. All rights reserved.

Analysing the environmental harms caused by coal mining and its protection measures in permafrost regions of Qinghai–Tibet Plateau

Directory of Open Access Journals (Sweden)

Wei Cao

2017-09-01

Full Text Available The coal mining has brought a series of ecological problems and environmental problems in permafrost regions. Taking Muli coal-mining area as an example, this article attempts to analyse the environmental harms caused by coal mining and its protection measures in permafrost regions of Qinghai–Tibet Plateau. This article analyses the influence of open mining on the surrounding permafrost around the open pit by using the numerical simulation. The results show that (1 based on the interrelation between coal mining and permafrost environment, these main environmental harm include the permafrost change and the natural environment change in cold regions; (2 once the surface temperature rises due to open mining, the permafrost will disappear with the increase of exploitation life. If considering the solar radiation, the climate conditions and the geological condition around the pit edge, the maximum thaw depth will be more than 2 m; (3 the protection measures are proposed to avoid the disadvantage impact on the permafrost environment caused by coal mining. It will provide a scientific basis for the resource development and environment protection in cold regions.

Management of Small Quantity of Nuclear Material at Locations Outside Facilities in Korea

Energy Technology Data Exchange (ETDEWEB)

Park, Seung Sik; Kim, Ki Hyun [KAERI, Daejeon (Korea, Republic of)

2016-05-15

Small quantity of nuclear material (SQNM) is prescribed to be less than specified minimum quantities of nuclear material in a facility. SQNM is used at the locations called locations outside facilities (LOFs). LOFs are used to control the locations and installations that store nuclear materials under one effective Kg, respectively. Holders of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or neither report them to the System of Accounting for and Control of nuclear material (SSAC) under specified quantities according to the Atomic Safety Law. Well defined safeguards law is fundamental to the effective control of nuclear material, facilities and nuclear related activities. In the current nuclear safety legislation, there are some exceptive clauses. Users of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or not report them to the national authority below specified amount.

Energy Drinks and Binge Drinking Predict College Students' Sleep Quantity, Quality, and Tiredness.

Science.gov (United States)

Patrick, Megan E; Griffin, Jamie; Huntley, Edward D; Maggs, Jennifer L