WorldWideScience

Sample records for maximum recommended concentration

  1. Maximum Recommended Dosage of Lithium for Pregnant Women Based on a PBPK Model for Lithium Absorption

    Directory of Open Access Journals (Sweden)

    Scott Horton

    2012-01-01

    Full Text Available Treatment of bipolar disorder with lithium therapy during pregnancy is a medical challenge. Bipolar disorder is more prevalent in women and its onset is often concurrent with peak reproductive age. Treatment typically involves administration of the element lithium, which has been classified as a class D drug (legal to use during pregnancy, but may cause birth defects and is one of only thirty known teratogenic drugs. There is no clear recommendation in the literature on the maximum acceptable dosage regimen for pregnant, bipolar women. We recommend a maximum dosage regimen based on a physiologically based pharmacokinetic (PBPK model. The model simulates the concentration of lithium in the organs and tissues of a pregnant woman and her fetus. First, we modeled time-dependent lithium concentration profiles resulting from lithium therapy known to have caused birth defects. Next, we identified maximum and average fetal lithium concentrations during treatment. Then, we developed a lithium therapy regimen to maximize the concentration of lithium in the mother’s brain, while maintaining the fetal concentration low enough to reduce the risk of birth defects. This maximum dosage regimen suggested by the model was 400 mg lithium three times per day.

  2. Maximum concentrations at work and maximum biologically tolerable concentration for working materials 1991

    International Nuclear Information System (INIS)

    1991-01-01

    The meaning of the term 'maximum concentration at work' in regard of various pollutants is discussed. Specifically, a number of dusts and smokes are dealt with. The valuation criteria for maximum biologically tolerable concentrations for working materials are indicated. The working materials in question are corcinogeneous substances or substances liable to cause allergies or mutate the genome. (VT) [de

  3. Maximum Permissible Concentrations and Negligible Concentrations for pesticides

    NARCIS (Netherlands)

    Crommentuijn T; Kalf DF; Polder MD; Posthumus R; Plassche EJ van de; CSR

    1997-01-01

    Maximum Permissible Concentrations (MPCs) and Negligible Concentrations (NCs) derived for a series of pesticides are presented in this report. These MPCs and NCs are used by the Ministry of Housing, Spatial Planning and the Environment (VROM) to set Environmental Quality Objectives. For some of the

  4. Scientific substantination of maximum allowable concentration of fluopicolide in water

    Directory of Open Access Journals (Sweden)

    Pelo I.М.

    2014-03-01

    Full Text Available In order to substantiate fluopicolide maximum allowable concentration in the water of water reservoirs the research was carried out. Methods of study: laboratory hygienic experiment using organoleptic and sanitary-chemical, sanitary-toxicological, sanitary-microbiological and mathematical methods. The results of fluopicolide influence on organoleptic properties of water, sanitary regimen of reservoirs for household purposes were given and its subthreshold concentration in water by sanitary and toxicological hazard index was calculated. The threshold concentration of the substance by the main hazard criteria was established, the maximum allowable concentration in water was substantiated. The studies led to the following conclusions: fluopicolide threshold concentration in water by organoleptic hazard index (limiting criterion – the smell – 0.15 mg/dm3, general sanitary hazard index (limiting criteria – impact on the number of saprophytic microflora, biochemical oxygen demand and nitrification – 0.015 mg/dm3, the maximum noneffective concentration – 0.14 mg/dm3, the maximum allowable concentration - 0.015 mg/dm3.

  5. Maximum phytoplankton concentrations in the sea

    DEFF Research Database (Denmark)

    Jackson, G.A.; Kiørboe, Thomas

    2008-01-01

    A simplification of plankton dynamics using coagulation theory provides predictions of the maximum algal concentration sustainable in aquatic systems. These predictions have previously been tested successfully against results from iron fertilization experiments. We extend the test to data collect...

  6. A discussion about maximum uranium concentration in digestion solution of U3O8 type uranium ore concentrate

    International Nuclear Information System (INIS)

    Xia Dechang; Liu Chao

    2012-01-01

    On the basis of discussing the influence of single factor on maximum uranium concentration in digestion solution,the influence degree of some factors such as U content, H 2 O content, mass ratio of P and U was compared and analyzed. The results indicate that the relationship between U content and maximum uranium concentration in digestion solution was direct ratio, while the U content increases by 1%, the maximum uranium concentration in digestion solution increases by 4.8%-5.7%. The relationship between H 2 O content and maximum uranium concentration in digestion solution was inverse ratio, the maximum uranium concentration in digestion solution decreases by 46.1-55.2 g/L while H 2 O content increases by 1%. The relationship between mass ratio of P and U and maximum uranium concentration in digestion solution was inverse ratio, the maximum uranium concentration in digestion solution decreases by 116.0-181.0 g/L while the mass ratio of P and U increase 0.1%. When U content equals 62.5% and the influence of mass ratio of P and U is no considered, the maximum uranium concentration in digestion solution equals 1 578 g/L; while mass ratio of P and U equals 0.35%, the maximum uranium concentration decreases to 716 g/L, the decreased rate is 54.6%, so the mass ratio of P and U in U 3 O 8 type uranium ore concentrate is the main controlling factor. (authors)

  7. Psychophysical basis for maximum pushing and pulling forces: A review and recommendations.

    Science.gov (United States)

    Garg, Arun; Waters, Thomas; Kapellusch, Jay; Karwowski, Waldemar

    2014-03-01

    The objective of this paper was to perform a comprehensive review of psychophysically determined maximum acceptable pushing and pulling forces. Factors affecting pushing and pulling forces are identified and discussed. Recent studies show a significant decrease (compared to previous studies) in maximum acceptable forces for males but not for females when pushing and pulling on a treadmill. A comparison of pushing and pulling forces measured using a high inertia cart with those measured on a treadmill shows that the pushing and pulling forces using high inertia cart are higher for males but are about the same for females. It is concluded that the recommendations of Snook and Ciriello (1991) for pushing and pulling forces are still valid and provide reasonable recommendations for ergonomics practitioners. Regression equations as a function of handle height, frequency of exertion and pushing/pulling distance are provided to estimate maximum initial and sustained forces for pushing and pulling acceptable to 75% male and female workers. At present it is not clear whether pushing or pulling should be favored. Similarly, it is not clear what handle heights would be optimal for pushing and pulling. Epidemiological studies are needed to determine relationships between psychophysically determined maximum acceptable pushing and pulling forces and risk of musculoskeletal injuries, in particular to low back and shoulders.

  8. Estimation of maximum credible atmospheric radioactivity concentrations and dose rates from nuclear tests

    International Nuclear Information System (INIS)

    Telegadas, K.

    1979-01-01

    A simple technique is presented for estimating maximum credible gross beta air concentrations from nuclear detonations in the atmosphere, based on aircraft sampling of radioactivity following each Chinese nuclear test from 1964 to 1976. The calculated concentration is a function of the total yield and fission yield, initial vertical radioactivity distribution, time after detonation, and rate of horizontal spread of the debris with time. calculated maximum credible concentrations are compared with the highest concentrations measured during aircraft sampling. The technique provides a reasonable estimate of maximum air concentrations from 1 to 10 days after a detonation. An estimate of the whole-body external gamma dose rate corresponding to the maximum credible gross beta concentration is also given. (author)

  9. Maximum tolerable radiation doses recommended by the Israel Advisory Committee on nuclear safety

    International Nuclear Information System (INIS)

    Tadmor, J.; Litai, D.; Lubin, E.

    1978-01-01

    Maximum tolerable doses have been recommended by the Israel Advisory Committee on Nuclear Safety. The recommendations which are based on a comparison with risks tolerated in other human activities, are for doses to radiation workers, for individual members of the population at the fence of a nuclear installation, and for the population at large, for both normal operating and accident conditions. Tolerable whole-body doses and doses to different critical organs are listed

  10. Maximum permissible concentrations and negligible concentrations for antifouling substances. Irgarol 1051, dichlofluanid, ziram, chlorothalonil and TCMTB

    NARCIS (Netherlands)

    Wezel AP van; Vlaardingen P van; CSR

    2001-01-01

    This report presents maximum permissible concentrations and negligible concentrations that have been derived for various antifouling substances used as substitutes for TBT. Included here are Irgarol 1051, dichlofluanide, ziram, chlorothalonil and TCMTB.

  11. Maximum permissible body burdens and maximum permissible concentrations of radionuclides in air and in water for occupational exposure. Recommendations of the National Committee on Radiation Protection. Handbook 69

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1959-06-05

    The present Handbook and its predecessors stem from the Second International Congress of Radiology, held in Stockholm in 1928. At that time, under the auspices of the Congress, the International Commission on Radiological Protection (ICRP) was organized to deal initially with problems of X-ray protection and later with radioactivity protection. At that time 'permissible' doses of X-rays were estimated primarily in terms of exposures which produced erythema, the amount of exposure which would produce a defined reddening of the skin. Obviously a critical problem in establishing criteria for radiation protection was one of developing useful standards and techniques of physical measurement. For this reason two of the organizations in this country with a major concern for X-ray protection, the American Roentgen Ray Society and the Radiology Society of North America, suggested that the National Bureau of Standards assume responsibility for organizing representative experts to deal with the problem. Accordingly, early in 1929, an Advisory Committee on X-ray and Radium Protection was organized to develop recommendations on the protection problem within the United States and to formulate United States points of view for presentation to the International Commission on Radiological Protection. The organization of the U.S. Advisory Committee included experts from both the medical and physical science fields. The recommendations of this Handbook take into consideration the NCRP statement entitled 'Maximum Permissible Radiation Exposures to Man', published as an addendum to Handbook 59 on April 15, 1958. As noted above this study was carried out jointly by the ICRP and the NCRP, and the complete report is more extensive than the material contained in this Handbook.

  12. Maximum permissible body burdens and maximum permissible concentrations of radionuclides in air and in water for occupational exposure. Recommendations of the National Committee on Radiation Protection. Handbook 69

    International Nuclear Information System (INIS)

    1959-01-01

    The present Handbook and its predecessors stem from the Second International Congress of Radiology, held in Stockholm in 1928. At that time, under the auspices of the Congress, the International Commission on Radiological Protection (ICRP) was organized to deal initially with problems of X-ray protection and later with radioactivity protection. At that time 'permissible' doses of X-rays were estimated primarily in terms of exposures which produced erythema, the amount of exposure which would produce a defined reddening of the skin. Obviously a critical problem in establishing criteria for radiation protection was one of developing useful standards and techniques of physical measurement. For this reason two of the organizations in this country with a major concern for X-ray protection, the American Roentgen Ray Society and the Radiology Society of North America, suggested that the National Bureau of Standards assume responsibility for organizing representative experts to deal with the problem. Accordingly, early in 1929, an Advisory Committee on X-ray and Radium Protection was organized to develop recommendations on the protection problem within the United States and to formulate United States points of view for presentation to the International Commission on Radiological Protection. The organization of the U.S. Advisory Committee included experts from both the medical and physical science fields. The recommendations of this Handbook take into consideration the NCRP statement entitled 'Maximum Permissible Radiation Exposures to Man', published as an addendum to Handbook 59 on April 15, 1958. As noted above this study was carried out jointly by the ICRP and the NCRP, and the complete report is more extensive than the material contained in this Handbook

  13. Double-tailored nonimaging reflector optics for maximum-performance solar concentration.

    Science.gov (United States)

    Goldstein, Alex; Gordon, Jeffrey M

    2010-09-01

    A nonimaging strategy that tailors two mirror contours for concentration near the étendue limit is explored, prompted by solar applications where a sizable gap between the optic and absorber is required. Subtle limitations of this simultaneous multiple surface method approach are derived, rooted in the manner in which phase space boundaries can be tailored according to the edge-ray principle. The fundamental categories of double-tailored reflective optics are identified, only a minority of which can pragmatically offer maximum concentration at high collection efficiency. Illustrative examples confirm that acceptance half-angles as large as 30 mrad can be realized at a flux concentration of approximately 1000.

  14. Training Research: Practical Recommendations for Maximum Impact

    Science.gov (United States)

    Beidas, Rinad S.; Koerner, Kelly; Weingardt, Kenneth R.; Kendall, Philip C.

    2011-01-01

    This review offers practical recommendations regarding research on training in evidence-based practices for mental health and substance abuse treatment. When designing training research, we recommend: (a) aligning with the larger dissemination and implementation literature to consider contextual variables and clearly defining terminology, (b) critically examining the implicit assumptions underlying the stage model of psychotherapy development, (c) incorporating research methods from other disciplines that embrace the principles of formative evaluation and iterative review, and (d) thinking about how technology can be used to take training to scale throughout all stages of a training research project. An example demonstrates the implementation of these recommendations. PMID:21380792

  15. Secondary poisoning of cadmium, copper and mercury: implications for the Maximum Permissible Concentrations and Negligible Concentrations in water, sediment and soil

    NARCIS (Netherlands)

    Smit CE; Wezel AP van; Jager T; Traas TP; CSR

    2000-01-01

    The impact of secondary poisoning on the Maximum Permissible Concentrations (MPCs) and Negligible Concentrations (NCs) of cadmium, copper and mercury in water, sediment and soil have been evaluated. Field data on accumulation of these elements by fish, mussels and earthworms were used to derive

  16. Maximum solid concentrations of coal water slurries predicted by neural network models

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Jun; Li, Yanchang; Zhou, Junhu; Liu, Jianzhong; Cen, Kefa

    2010-12-15

    The nonlinear back-propagation (BP) neural network models were developed to predict the maximum solid concentration of coal water slurry (CWS) which is a substitute for oil fuel, based on physicochemical properties of 37 typical Chinese coals. The Levenberg-Marquardt algorithm was used to train five BP neural network models with different input factors. The data pretreatment method, learning rate and hidden neuron number were optimized by training models. It is found that the Hardgrove grindability index (HGI), moisture and coalification degree of parent coal are 3 indispensable factors for the prediction of CWS maximum solid concentration. Each BP neural network model gives a more accurate prediction result than the traditional polynomial regression equation. The BP neural network model with 3 input factors of HGI, moisture and oxygen/carbon ratio gives the smallest mean absolute error of 0.40%, which is much lower than that of 1.15% given by the traditional polynomial regression equation. (author)

  17. Evaluation of maximum radionuclide concentration from decay chains migration in aquifers

    International Nuclear Information System (INIS)

    Aquino Branco, O.E. de.

    1983-01-01

    The mathematical formulation of the mechanisms involved in the transport of contaminants in aquifers is presented. The methodology employed is described. A method of calculation the maximum concentration of radionuclides migrating in the underground water, and resulting from one decay chain, is then proposed. As an example, the methodology is applied to a waste basin, built to receive effluents from a hypothectical uranium ore mining and milling facility. (M.A.C.) [pt

  18. Maximum permissible concentration (MPC) values for spontaneously fissioning radionuclides

    International Nuclear Information System (INIS)

    Ford, M.R.; Snyder, W.S.; Dillman, L.T.; Watson, S.B.

    1976-01-01

    The radiation hazards involved in handling certain of the transuranic nuclides that exhibit spontaneous fission as a mode of decay were reaccessed using recent advances in dosimetry and metabolic modeling. Maximum permissible concentration (MPC) values in air and water for occupational exposure (168 hr/week) were calculated for 244 Pu, 246 Cm, 248 Cm, 250 Cf, 252 Cf, 254 Cf, /sup 254m/Es, 255 Es, 254 Fm, and 256 Fm. The half-lives, branching ratios, and principal modes of decay of the parent-daughter members down to a member that makes a negligible contribution to the dose are given, and all daughters that make a significant contribution to the dose to body organs following inhalation or ingestion are included in the calculations. Dose commitments for body organs are also given

  19. Organic solvents impair life-traits and biomarkers in the New Zealand mudsnail Potamopyrgus antipodarum (Gray) at concentrations below OECD recommendations

    International Nuclear Information System (INIS)

    Lecomte, V.; Noury, P.; Tutundjian, R.; Buronfosse, T.; Garric, J.; Gust, M.

    2013-01-01

    Highlights: •Acetone (20 μl l −1 ) accelerates embryonic development in Potamopyrgus antipodarum. •Ethanol (20 μl l −1 ) decreases growth in juvenile mudsnails. •Acetone, ethanol, methanol and DMSO increase E2 levels in snails. •Carrier solvents impair gene expression. •DMSO is to be preferred. -- Abstract: Potamopyrgus antipodarum is a gastropod mollusk proposed for use in the development of reproduction tests within the Organization for Economic Cooperation and Development (OECD). Numerous chemicals, including endocrine disrupters, are relatively water-insoluble, and water-miscible solvents are currently used for testing them. OECD recommends a maximum concentration of 100 μl l −1 . As several studies highlighted effects of lower concentrations of solvents, this study assessed the effects of 20 μl l −1 acetone, ethanol, methanol and dimethylsulfoxide (DMSO) on juvenile and adult snails during 42 days. Ethanol decreased juvenile growth, while acetone increased the rate of embryonic development. All solvents increased estradiol-like levels in adult snails. DMSO only increased mRNA expression of vitellogenin-like gene, while acetone, ethanol and methanol decreased mRNA expression of three nuclear receptor (estrogen receptor-like, ecdysone-induced protein and chicken ovalbumin upstream promoter transcription factor) genes as well as of genes encoding proteins involved in genomic (prohibitin-2) and non-genomic (striatin) pathways of estrogens activity in vertebrates. This study highlights the confounding effects of low concentrations of solvents and recommends avoiding their use. Where solvent use is inevitable, their concentrations and type should be investigated for suitability for the measured endpoints prior to use in chemical testing strategies

  20. Organic solvents impair life-traits and biomarkers in the New Zealand mudsnail Potamopyrgus antipodarum (Gray) at concentrations below OECD recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Lecomte, V.; Noury, P.; Tutundjian, R. [Irstea, UR MAEP, Laboratoire d’écotoxicologie, 5 rue de la Doua, CS70077, 69626 Villeurbanne Cedex (France); Buronfosse, T. [VetAgro-Sup, Campus vétérinaire, Endocrinology Laboratory, 69280 Marcy l’Etoile (France); Garric, J. [Irstea, UR MAEP, Laboratoire d’écotoxicologie, 5 rue de la Doua, CS70077, 69626 Villeurbanne Cedex (France); Gust, M., E-mail: marion.gust@irstea.fr [Irstea, UR MAEP, Laboratoire d’écotoxicologie, 5 rue de la Doua, CS70077, 69626 Villeurbanne Cedex (France)

    2013-09-15

    Highlights: •Acetone (20 μl l{sup −1}) accelerates embryonic development in Potamopyrgus antipodarum. •Ethanol (20 μl l{sup −1}) decreases growth in juvenile mudsnails. •Acetone, ethanol, methanol and DMSO increase E2 levels in snails. •Carrier solvents impair gene expression. •DMSO is to be preferred. -- Abstract: Potamopyrgus antipodarum is a gastropod mollusk proposed for use in the development of reproduction tests within the Organization for Economic Cooperation and Development (OECD). Numerous chemicals, including endocrine disrupters, are relatively water-insoluble, and water-miscible solvents are currently used for testing them. OECD recommends a maximum concentration of 100 μl l{sup −1}. As several studies highlighted effects of lower concentrations of solvents, this study assessed the effects of 20 μl l{sup −1} acetone, ethanol, methanol and dimethylsulfoxide (DMSO) on juvenile and adult snails during 42 days. Ethanol decreased juvenile growth, while acetone increased the rate of embryonic development. All solvents increased estradiol-like levels in adult snails. DMSO only increased mRNA expression of vitellogenin-like gene, while acetone, ethanol and methanol decreased mRNA expression of three nuclear receptor (estrogen receptor-like, ecdysone-induced protein and chicken ovalbumin upstream promoter transcription factor) genes as well as of genes encoding proteins involved in genomic (prohibitin-2) and non-genomic (striatin) pathways of estrogens activity in vertebrates. This study highlights the confounding effects of low concentrations of solvents and recommends avoiding their use. Where solvent use is inevitable, their concentrations and type should be investigated for suitability for the measured endpoints prior to use in chemical testing strategies.

  1. The maximum ground level concentration of air pollutant and the effect of plume rise on concentration estimates

    International Nuclear Information System (INIS)

    Mayhoub, A.B.; Azzam, A.

    1991-01-01

    The emission of an air pollutant from an elevated point source according to Gaussian plume model has been presented. An elementary theoretical treatment for both the highest possible ground-level concentration and the downwind distance at which this maximum occurs for different stability classes has been constructed. The effective height release modification was taken into consideration. An illustrative case study, namely, the emission from the research reactor in Inchas, has been studied. The results of these analytical treatments and of the derived semi-empirical formulae are discussed and presented in few illustrative diagrams

  2. Conclusions and recommendations

    International Nuclear Information System (INIS)

    Carrette, M.

    1997-01-01

    The paper presents conclusions and recommendations at the closing session of the NEA/OECD Workshop held at Fontenay-aux-Roses on 12-14 June 1995. The conclusions refer to issues like: public reaction to foodstuffs containing radioisotope concentrations under the danger standards, possible non-adherence of manufacturers, processors, distributors, et al, to the instructions and guidance from radiation protection specialists, integration of all the food chain factors in the elaboration of the emergency intervention programs, etc. Among the most significant recommendations the following may be mentioned: 1. Differences between different intervention levels and the maximum admissible levels agreed upon by national, regional or international nutrition authorities should be further studied; 2. Problems created by the Chernobyl accident (as for instance, the methods of treatment of food chain products containing unacceptable radioactivity concentrations) are still present and must be solved; 3. Further studies should be done on the socio-cultural aspects of the communication, particularly on the information in rural environment; 4. The preventive measures in agriculture should be implemented as rapidly as possible; 5. In elaborating programmes of agriculture countermeasures, the management of contaminated media, particularly, of forests and their effect on agriculture

  3. Soil and Water Assessment Tool model predictions of annual maximum pesticide concentrations in high vulnerability watersheds.

    Science.gov (United States)

    Winchell, Michael F; Peranginangin, Natalia; Srinivasan, Raghavan; Chen, Wenlin

    2018-05-01

    Recent national regulatory assessments of potential pesticide exposure of threatened and endangered species in aquatic habitats have led to increased need for watershed-scale predictions of pesticide concentrations in flowing water bodies. This study was conducted to assess the ability of the uncalibrated Soil and Water Assessment Tool (SWAT) to predict annual maximum pesticide concentrations in the flowing water bodies of highly vulnerable small- to medium-sized watersheds. The SWAT was applied to 27 watersheds, largely within the midwest corn belt of the United States, ranging from 20 to 386 km 2 , and evaluated using consistent input data sets and an uncalibrated parameterization approach. The watersheds were selected from the Atrazine Ecological Exposure Monitoring Program and the Heidelberg Tributary Loading Program, both of which contain high temporal resolution atrazine sampling data from watersheds with exceptionally high vulnerability to atrazine exposure. The model performance was assessed based upon predictions of annual maximum atrazine concentrations in 1-d and 60-d durations, predictions critical in pesticide-threatened and endangered species risk assessments when evaluating potential acute and chronic exposure to aquatic organisms. The simulation results showed that for nearly half of the watersheds simulated, the uncalibrated SWAT model was able to predict annual maximum pesticide concentrations within a narrow range of uncertainty resulting from atrazine application timing patterns. An uncalibrated model's predictive performance is essential for the assessment of pesticide exposure in flowing water bodies, the majority of which have insufficient monitoring data for direct calibration, even in data-rich countries. In situations in which SWAT over- or underpredicted the annual maximum concentrations, the magnitude of the over- or underprediction was commonly less than a factor of 2, indicating that the model and uncalibrated parameterization

  4. Recommendation concerning maximum permissible radioactivity in animal feeds in case of a nuclear accident or other type of radiological emergency

    International Nuclear Information System (INIS)

    1988-01-01

    The SSK in its advice to the Federal Ministry of the Environment, Nature Conservation and Reactor Safety recommends to abstain from determining maximum permissible values to be applied in such cases of emergency. If, however, official limits are to be given, the following should be considered: (1) Distinction has to be made between animal feeds not subject to restrictive application with regard to time, animal species, or food chain (meat, milk, eggs), and those animal feeds whose application is subject to restrictions defined. (2) Maximum permissible activity data for animal feeds for restricted use should be ten times the value determined for non-restricted feeds. As to consultations within the EC on supplemtary tables to EC Directive No. 3954/87, the SSK presented its proposals in tables, using transfer factors from the literature concerning assessment of maximum permissible chronic intake of Cs-137, I-131, Sr-90, Pu-239, Am-241 by productive livestock (bovine, goats, sheep, swine, poultry). (HP) [de

  5. New ICRP recommendations on occupational limits for radon daughters

    International Nuclear Information System (INIS)

    Jacobi, W.

    1981-01-01

    The ICRP has recommended in 1959 for the first time a maximum permissible concentration (MPC) for the occupational exposure to radon and its short-lived daughters. Since this time more realistic dosimetric models for radon daughters have been developed. Taking into account epidemiological and new dosimetric findings the ICRP has adopted in March this year new recommendations on occupational limits for inhalation of 222 Rn, 220 Rn and their short-lived daughters. This report will be published this year as ICRP Publication 32 (ICRP 1981). The recommended limits for radon daughters were derived from the basic dose and risk limits as they were proposed by ICRP in its new basic recommendations (ICRP Publ. 26, 1977). In the following this basic system of dose limitation is shortly outlined before the special recommendations for radon daughters are described

  6. Influence of the composition of radionuclide mixtures on the maximum permissible concentration

    International Nuclear Information System (INIS)

    Schillinger, K.; Schuricht, V.

    1975-08-01

    By dividing radionuclides according to their formation mechanisms it is possible to assess the influence of separate partial mixtures on the maximum permissible concentration (MPC) of the total mixture without knowing exactly their contribution to the total activity. Calculations showed that the MPC of a total mixture of unsoluble radionuclides, which may occur in all fields of peaceful uses of nuclear energy, depends on the gastrointestinal tract as the critical organ and on the composition of the fission product mixture. The influence of fractionation on the MPC can be reglected in such a case, whereas in case of soluble radionuclides this is not possible

  7. [Polish guidelines of 2001 for maximum admissible intensities in high frequency EMF versus European Union recommendations].

    Science.gov (United States)

    Aniołczyk, Halina

    2003-01-01

    In 1999, a draft of amendments to maximum admissible intensities (MAI) of electromagnetic fields (0 Hz-300 GHz) was prepared by Professor H. Korniewicz of the Central Institute for Labour Protection, Warsaw, in cooperation with the Nofer Institute of Occupational Medicine, Łódź (radio- and microwaves) and the Military Institute of Hygiene and Epidemiology, Warsaw (pulse radiation). Before 2000, the development of the national MAI guidelines for the frequency range of 0.1 MHz-300 GHz was based on the knowledge of biological and health effects of EMF exposure available on the turn of the 1960s. A current basis for establishing the MAI international standards is a well-documented thermal effect measured by the value of a specific absorption rate (SAR), whereas the effects of resonant absorption imposes the nature of the functional dependency on EMF frequency. The Russian standards, already thoroughly analyzed, still take so-called non-thermal effects and the conception of energetic load for a work-shift with its progressive averaging (see hazardous zone in Polish guidelines) as a basis for setting maximum admissible intensities. The World Health Organization recommends a harmonization of the EMF protection guidelines, existing in different countries, with the guidelines of the International Commission for Non-Ionizing Radiation Protection (ICNIRP), and its position is supported by the European Union.

  8. MAK and BAT values list 2017. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

    International Nuclear Information System (INIS)

    2017-01-01

    The MAK and BAT values list 2017 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

  9. MAK and BAT values list 2016. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

    International Nuclear Information System (INIS)

    2016-01-01

    The MAK and BAT values list 2016 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

  10. Use of MICRAS code on the evaluation of the maximum radionuclides concentrations due to transport/migration of decay chain in groundwaters

    International Nuclear Information System (INIS)

    Aquino Branco, O.E. de

    1995-01-01

    This paper presents a methodology for the evaluation of the maximum radionuclides concentrations in groundwaters, due to the transport/migration of decay chains. Analytical solution of the equations system is difficult, even if only three elements of the decay chain are considered. Therefore, a numerical solution is most convenient. An application of the MICRAS code, developed to assess maximum concentrations of each radionuclide, starting with the initial concentrations, is presented. The maximum concentration profile for 226 Ra, calculated using MICRAS, is compared with the results obtained through an analytical and a numerical model. The fitness of results is considered good. Simplified models, like the one represented by the application of MICRAS, are largely employed in the section in the selection and characterization of sites for radioactive wastes repositories and in studies of safety evaluation for the same purpose. A detailed analysis of the transport/migration of contaminants in aquifers requires a large quantify of data from the site and from the installation as well, which makes this analysis expensive and inviable during the preliminary phases of the studies. (author). 6 refs, 1 fig, 1 tab

  11. Recommendation of maximum allowable noise levels for offshore wind power systems; Empfehlung von Laermschutzwerten bei der Errichtung von Offshore-Windenergieanlagen (OWEA)

    Energy Technology Data Exchange (ETDEWEB)

    Werner, Stefanie [Umweltbundesamt, Dessau-Rosslau (Germany). Fachgebiet II 2.3

    2011-05-15

    When offshore wind farms are constructed, every single pile is hammered into the sediment by a hydraulic hammer. Noise levels at Horns Reef wind farm were in the range of 235 dB. The noise may cause damage to the auditory system of marine mammals. The Federal Environmental Office therefore recommends the definition of maximum permissible noise levels. Further, care should be taken that no marine mammals are found in the immediate vicinity of the construction site. (AKB)

  12. Shelf-Life of Chlorine Solutions Recommended in Ebola Virus Disease Response.

    Science.gov (United States)

    Iqbal, Qais; Lubeck-Schricker, Maya; Wells, Emma; Wolfe, Marlene K; Lantagne, Daniele

    2016-01-01

    In Ebola Virus Disease (EVD) outbreaks, it is widely recommended to wash living things (handwashing) with 0.05% (500 mg/L) chlorine solution and non-living things (surfaces, personal protective equipment, dead bodies) with 0.5% (5,000 mg/L) chlorine solution. Chlorine solutions used in EVD response are primarily made from powdered calcium hypochlorite (HTH), granular sodium dichloroisocyanurate (NaDCC), and liquid sodium hypochlorite (NaOCl), and have a pH range of 5-11. Chlorine solutions degrade following a reaction highly dependent on, and unusually sensitive to, pH, temperature, and concentration. We determined the shelf-life of 0.05% and 0.5% chlorine solutions used in EVD response, including HTH, NaDCC, stabilized NaOCl, generated NaOCl, and neutralized NaOCl solutions. Solutions were stored for 30 days at 25, 30, and 35°C, and tested daily for chlorine concentration and pH. Maximum shelf-life was defined as days until initial concentration fell to pH = 7) had a maximum shelf-life of a few hours, NaDCC solutions (pH = 6) 2 days, generated NaOCl solutions (pH = 9) 6 days, and HTH and stabilized NaOCl solutions (pH 9-11) >30 days. Models were developed for solutions with maximum shelf-lives between 1-30 days. Extrapolating to 40°C, the maximum predicted shelf-life for 0.05% and 0.5% NaDCC solutions were 0.38 and 0.82 hours, respectively; predicted shelf-life for 0.05% and 0.5% generated NaOCl solutions were >30 and 5.4 days, respectively. Each chlorine solution type offers advantages and disadvantages to responders, as: NaDCC is an easy-to-import high-concentration effervescent powder; HTH is similar, but forms a precipitate that may clog pipes; and, NaOCl solutions can be made locally, but are difficult to transport. We recommend responders chose the most appropriate source chlorine compound for their use, and ensure solutions are stored at appropriate temperatures and used or replaced before expiring.

  13. MAK and BAT values list 2015. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

    International Nuclear Information System (INIS)

    2015-01-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2015 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  14. MAK and BAT values list 2014. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

    International Nuclear Information System (INIS)

    2014-01-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2014 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  15. Shelf-Life of Chlorine Solutions Recommended in Ebola Virus Disease Response.

    Directory of Open Access Journals (Sweden)

    Qais Iqbal

    Full Text Available In Ebola Virus Disease (EVD outbreaks, it is widely recommended to wash living things (handwashing with 0.05% (500 mg/L chlorine solution and non-living things (surfaces, personal protective equipment, dead bodies with 0.5% (5,000 mg/L chlorine solution. Chlorine solutions used in EVD response are primarily made from powdered calcium hypochlorite (HTH, granular sodium dichloroisocyanurate (NaDCC, and liquid sodium hypochlorite (NaOCl, and have a pH range of 5-11. Chlorine solutions degrade following a reaction highly dependent on, and unusually sensitive to, pH, temperature, and concentration. We determined the shelf-life of 0.05% and 0.5% chlorine solutions used in EVD response, including HTH, NaDCC, stabilized NaOCl, generated NaOCl, and neutralized NaOCl solutions. Solutions were stored for 30 days at 25, 30, and 35°C, and tested daily for chlorine concentration and pH. Maximum shelf-life was defined as days until initial concentration fell to 30 days. Models were developed for solutions with maximum shelf-lives between 1-30 days. Extrapolating to 40°C, the maximum predicted shelf-life for 0.05% and 0.5% NaDCC solutions were 0.38 and 0.82 hours, respectively; predicted shelf-life for 0.05% and 0.5% generated NaOCl solutions were >30 and 5.4 days, respectively. Each chlorine solution type offers advantages and disadvantages to responders, as: NaDCC is an easy-to-import high-concentration effervescent powder; HTH is similar, but forms a precipitate that may clog pipes; and, NaOCl solutions can be made locally, but are difficult to transport. We recommend responders chose the most appropriate source chlorine compound for their use, and ensure solutions are stored at appropriate temperatures and used or replaced before expiring.

  16. Benefits of the maximum tolerated dose (MTD) and maximum tolerated concentration (MTC) concept in aquatic toxicology

    International Nuclear Information System (INIS)

    Hutchinson, Thomas H.; Boegi, Christian; Winter, Matthew J.; Owens, J. Willie

    2009-01-01

    development of sound criteria for data interpretation when the exposure of organisms has exceeded the MTD. While the MTD approach is well established for oral, topical, inhalational or injection exposure routes in mammalian toxicology, we propose that for exposure of aquatic organisms via immersion, the term Maximum Tolerated Concentration (MTC) is more appropriate

  17. A comparison of muscle activity in concentric and counter movement maximum bench press.

    Science.gov (United States)

    van den Tillaar, Roland; Ettema, Gertjan

    2013-01-01

    The purpose of this study was to compare the kinematics and muscle activation patterns of regular free-weight bench press (counter movement) with pure concentric lifts in the ascending phase of a successful one repetition maximum (1-RM) attempt in the bench press. Our aim was to evaluate if diminishing potentiation could be the cause of the sticking region. Since diminishing potentiation cannot occur in pure concentric lifts, the occurrence of a sticking region in this type of muscle actions would support the hypothesis that the sticking region is due to a poor mechanical position. Eleven male participants (age 21.9 ± 1.7 yrs, body mass 80.7 ± 10.9 kg, body height 1.79 ± 0.07 m) conducted 1-RM lifts in counter movement and in pure concentric bench presses in which kinematics and EMG activity were measured. In both conditions, a sticking region occurred. However, the start of the sticking region was different between the two bench presses. In addition, in four of six muscles, the muscle activity was higher in the counter movement bench press compared to the concentric one. Considering the findings of the muscle activity of six muscles during the maximal lifts it was concluded that the diminishing effect of force potentiation, which occurs in the counter movement bench press, in combination with a delayed muscle activation unlikely explains the existence of the sticking region in a 1-RM bench press. Most likely, the sticking region is the result of a poor mechanical force position.

  18. Application of ICRP recommendations relevant to internal dose

    International Nuclear Information System (INIS)

    Cowser, K.E.; Snyder, W.S.; Struxness, E.G.

    1969-01-01

    The intent of this paper is to review several of the basic concepts of radiation protection (with emphasis on internal dose) currently recommended by the International Commission on radiological Protection (ICRP), to summarize the assumptions and methods used in the calculation of internal dose, and to illustrate by example the practical application of the pertinent guidelines. Two broad subject areas are considered: (1) standards of radiation protection and (2) bases of internal dose estimation. Topics discussed within the framework of radiation protection standards include maximum permissible dose, categories of radiation exposure, maximum permissible dose commitment, simultaneous internal and external exposure, multiple organ exposure, and size of the exposed group. Discussion of internal dose estimation is limited to selected items that include the body burden of radionuclides and the calculation of absorbed dose, the dose equivalent, the derivation of maximum permissible concentration (MPC), the relationship of stable element intake to the MPC, and short term and chronic exposure situations. (author)

  19. Application of ICRP recommendations relevant to internal dose

    Energy Technology Data Exchange (ETDEWEB)

    Cowser, K E; Snyder, W S; Struxness, E G [Health Physics Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States)

    1969-07-01

    The intent of this paper is to review several of the basic concepts of radiation protection (with emphasis on internal dose) currently recommended by the International Commission on radiological Protection (ICRP), to summarize the assumptions and methods used in the calculation of internal dose, and to illustrate by example the practical application of the pertinent guidelines. Two broad subject areas are considered: (1) standards of radiation protection and (2) bases of internal dose estimation. Topics discussed within the framework of radiation protection standards include maximum permissible dose, categories of radiation exposure, maximum permissible dose commitment, simultaneous internal and external exposure, multiple organ exposure, and size of the exposed group. Discussion of internal dose estimation is limited to selected items that include the body burden of radionuclides and the calculation of absorbed dose, the dose equivalent, the derivation of maximum permissible concentration (MPC), the relationship of stable element intake to the MPC, and short term and chronic exposure situations. (author)

  20. Concentration Limits in the Cement Based Swiss Repository for Long-lived, Intermediate-level Radioactive Wastes (LMA)

    International Nuclear Information System (INIS)

    Berner, Urs

    1999-12-01

    The Swiss repository concept for long-lived, intermediate-level radioactive wastes (LMA), in Swiss terminology) foresees cylindrical concrete silos surrounded by a ring of granulated bentonite to deposit the waste. As one of the possible options and similar to the repository for high level wastes, the silos will be located in a deep crystalline host rock. Solidified with concrete in steel drums, the waste is stacked into a silo and the silo is then backfilled with a porous mortar. To characterize the release of radionuclides from the repository, the safety assessment considers first the dissolution into the pore water of the concrete, and then diffusion through the outer bentonite ring into the deep crystalline groundwater. For 19 safety relevant radionuclides (isotopes of U, Th, Pa, Np, Pu, Am, Ni, Zr, Mo, Nb, Se, Sr, Ra, Tc, Sn, I, C, Cs, Cl) the report recommends maximum elemental concentrations to be expected in the cement pore water of the particularly considered repository. These limits will form the parameter base for subsequent release model chains. Concentration limits in a geochemical environment are usually obtained from thermodynamic equilibrium calculations performed with geochemical speciation codes. However, earlier studies revealed that this procedure does not always lead to reliable results. Main reasons for this are the complexity of the systems considered, as well as the lacking completeness of, and the uncertainty associated with the thermodynamic data. To improve the recommended maximum concentrations for a distinct repository design, this work includes additional design- and system-dependent criteria. The following processes, inventories and properties are considered in particular: a) recent experimental investigations, particularly from cement systems, b) thermodynamic model calculations when reliable data are available, c) total inventories of radionuclides, d) sorption- and co-precipitation processes, e) dilution with stable isotopes, f

  1. The moving-window Bayesian maximum entropy framework: estimation of PM(2.5) yearly average concentration across the contiguous United States.

    Science.gov (United States)

    Akita, Yasuyuki; Chen, Jiu-Chiuan; Serre, Marc L

    2012-09-01

    Geostatistical methods are widely used in estimating long-term exposures for epidemiological studies on air pollution, despite their limited capabilities to handle spatial non-stationarity over large geographic domains and the uncertainty associated with missing monitoring data. We developed a moving-window (MW) Bayesian maximum entropy (BME) method and applied this framework to estimate fine particulate matter (PM(2.5)) yearly average concentrations over the contiguous US. The MW approach accounts for the spatial non-stationarity, while the BME method rigorously processes the uncertainty associated with data missingness in the air-monitoring system. In the cross-validation analyses conducted on a set of randomly selected complete PM(2.5) data in 2003 and on simulated data with different degrees of missing data, we demonstrate that the MW approach alone leads to at least 17.8% reduction in mean square error (MSE) in estimating the yearly PM(2.5). Moreover, the MWBME method further reduces the MSE by 8.4-43.7%, with the proportion of incomplete data increased from 18.3% to 82.0%. The MWBME approach leads to significant reductions in estimation error and thus is recommended for epidemiological studies investigating the effect of long-term exposure to PM(2.5) across large geographical domains with expected spatial non-stationarity.

  2. The moving-window Bayesian Maximum Entropy framework: Estimation of PM2.5 yearly average concentration across the contiguous United States

    Science.gov (United States)

    Akita, Yasuyuki; Chen, Jiu-Chiuan; Serre, Marc L.

    2013-01-01

    Geostatistical methods are widely used in estimating long-term exposures for air pollution epidemiological studies, despite their limited capabilities to handle spatial non-stationarity over large geographic domains and uncertainty associated with missing monitoring data. We developed a moving-window (MW) Bayesian Maximum Entropy (BME) method and applied this framework to estimate fine particulate matter (PM2.5) yearly average concentrations over the contiguous U.S. The MW approach accounts for the spatial non-stationarity, while the BME method rigorously processes the uncertainty associated with data missingnees in the air monitoring system. In the cross-validation analyses conducted on a set of randomly selected complete PM2.5 data in 2003 and on simulated data with different degrees of missing data, we demonstrate that the MW approach alone leads to at least 17.8% reduction in mean square error (MSE) in estimating the yearly PM2.5. Moreover, the MWBME method further reduces the MSE by 8.4% to 43.7% with the proportion of incomplete data increased from 18.3% to 82.0%. The MWBME approach leads to significant reductions in estimation error and thus is recommended for epidemiological studies investigating the effect of long-term exposure to PM2.5 across large geographical domains with expected spatial non-stationarity. PMID:22739679

  3. Concentration dependence of biotransformation in fish liver S9: Optimizing substrate concentrations to estimate hepatic clearance for bioaccumulation assessment.

    Science.gov (United States)

    Lo, Justin C; Allard, Gayatri N; Otton, S Victoria; Campbell, David A; Gobas, Frank A P C

    2015-12-01

    In vitro bioassays to estimate biotransformation rate constants of contaminants in fish are currently being investigated to improve bioaccumulation assessments of hydrophobic contaminants. The present study investigates the relationship between chemical substrate concentration and in vitro biotransformation rate of 4 environmental contaminants (9-methylanthracene, pyrene, chrysene, and benzo[a]pyrene) in rainbow trout (Oncorhynchus mykiss) liver S9 fractions and methods to determine maximum first-order biotransformation rate constants. Substrate depletion experiments using a series of initial substrate concentrations showed that in vitro biotransformation rates exhibit strong concentration dependence, consistent with a Michaelis-Menten kinetic model. The results indicate that depletion rate constants measured at initial substrate concentrations of 1 μM (a current convention) could underestimate the in vitro biotransformation potential and may cause bioconcentration factors to be overestimated if in vitro biotransformation rates are used to assess bioconcentration factors in fish. Depletion rate constants measured using thin-film sorbent dosing experiments were not statistically different from the maximum depletion rate constants derived using a series of solvent delivery-based depletion experiments for 3 of the 4 test chemicals. Multiple solvent delivery-based depletion experiments at a range of initial concentrations are recommended for determining the concentration dependence of in vitro biotransformation rates in fish liver fractions, whereas a single sorbent phase dosing experiment may be able to provide reasonable approximations of maximum depletion rates of very hydrophobic substances. © 2015 SETAC.

  4. Mercury in fish from two Nicaraguan lakes: A recommendation for increased monitoring of fish for international commerce

    International Nuclear Information System (INIS)

    McCrary, Jeffrey K.; Castro, Mark; McKaye, Kenneth R.

    2006-01-01

    We measured total mercury concentrations in water and fish of Lake Managua and Lake Apoyo. Water mercury concentrations were 10-fold higher in Lake Managua than in Lake Apoyo, although differences in mercury concentration in the most common native fish were not significant. One-fourth of the commercially fished tilapia in Lake Managua exceeded maximum recommended mercury levels for consumption among pregnant women and other at-risk groups, although bioavailability to fishes was lower than in previously studied sites in Brazil and Western Maryland. The lower bioavailiability may present important information for management options to reduce mercury exposure to fishes and humans. We recommend closer mercury monitoring among freshwater fish destined for international commerce. - Fish commonly exported into the international food supply may be contaminated with mercury

  5. Mercury in fish from two Nicaraguan lakes: A recommendation for increased monitoring of fish for international commerce

    Energy Technology Data Exchange (ETDEWEB)

    McCrary, Jeffrey K. [University of Central America, Apdo. 69, Managua (Nicaragua) and College of Natural Resources, Virginia Tech, Blacksburg, VA 24061 (United States)]. E-mail: jmccrary2@yahoo.com; Castro, Mark [Appalachian Laboratory, University of Maryland Center for Environmental Science, 301 Braddock Road, Frostburg, MD 21532 (United States); McKaye, Kenneth R. [University of Central America, Apdo. 69, Managua (Nicaragua); Appalachian Laboratory, University of Maryland Center for Environmental Science, 301 Braddock Road, Frostburg, MD 21532 (United States)

    2006-06-15

    We measured total mercury concentrations in water and fish of Lake Managua and Lake Apoyo. Water mercury concentrations were 10-fold higher in Lake Managua than in Lake Apoyo, although differences in mercury concentration in the most common native fish were not significant. One-fourth of the commercially fished tilapia in Lake Managua exceeded maximum recommended mercury levels for consumption among pregnant women and other at-risk groups, although bioavailability to fishes was lower than in previously studied sites in Brazil and Western Maryland. The lower bioavailiability may present important information for management options to reduce mercury exposure to fishes and humans. We recommend closer mercury monitoring among freshwater fish destined for international commerce. - Fish commonly exported into the international food supply may be contaminated with mercury.

  6. Maximum neutron flux in thermal reactors

    International Nuclear Information System (INIS)

    Strugar, P.V.

    1968-12-01

    Direct approach to the problem is to calculate spatial distribution of fuel concentration if the reactor core directly using the condition of maximum neutron flux and comply with thermal limitations. This paper proved that the problem can be solved by applying the variational calculus, i.e. by using the maximum principle of Pontryagin. Mathematical model of reactor core is based on the two-group neutron diffusion theory with some simplifications which make it appropriate from maximum principle point of view. Here applied theory of maximum principle are suitable for application. The solution of optimum distribution of fuel concentration in the reactor core is obtained in explicit analytical form. The reactor critical dimensions are roots of a system of nonlinear equations and verification of optimum conditions can be done only for specific examples

  7. Comments on the recommendations of the International Commission on Radiological Protection

    Energy Technology Data Exchange (ETDEWEB)

    Pochin, E E; Rock Carling, Ernest; Court Brown, W M [Medical Research Council, Committee on Protection against Ionizing Radiations, London (United Kingdom); and others

    1960-12-01

    exposed. Exposure of members of special groups - 7. The Committee interprets the Commission's recommendation (para. 56) on maximum permissible concentrations in air and water as applying to average concentrations over periods of a year. The recommendation in para. 57 is similarly taken to refer to average concentrations over periods of a year. These interpretations are consistent with the averaging period adopted by the Commission for populations at large (para. 68). Exposure of the population at large - 8. The Commission suggests (para. 64) that the genetic dose (as defined in para. 63) to the whole population from all sources additional to the natural background shall not exceed 5 rems plus the lowest practicable contribution from medical exposure of patients. In the light of the limitations dealt with in paras. 59 and 60, the Committee is Prepared to accept the suggested figure as the upper limit. It considers, however, that the operative figure should in fact be determined by considering the levels which should be allowed for different sources of radiation (of the types given in the addendum to para. 65). Subject to a maximum value of rems, this operative figure would thus be ascertained by adding the figures regarded as permissible for individual sources, the contribution from each being held to the lowest practicable value. (author)

  8. Radon concentrations in ground and drinking water in the state of Chihuahua, Mexico

    International Nuclear Information System (INIS)

    Villalba, L.; Colmenero Sujo, L.; Montero Cabrera, M.E.; Cano Jimenez, A.; Renteria Villalobos, M.; Delgado Mendoza, C.J.; Jurado Tenorio, L.A.; Davila Rangel, I.; Herrera Peraza, E.F.

    2005-01-01

    This paper reports 222 Rn concentrations in ground and drinking water of nine cities of Chihuahua State, Mexico. Fifty percent of the 114 sampled wells exhibited 222 Rn concentrations exceeding 11 Bq/L, the maximum contaminant level (MCL) recommended by the USEPA. Furthermore, around 48% (123 samples) of the tap-water samples taken from 255 dwellings showed radon concentrations over the MCL. There is an apparent correlation between total dissolved solids and radon concentration in ground-water. The high levels of 222 Rn found may be entirely attributed to the nature of aquifer rocks

  9. Radon concentrations in ground and drinking water in the state of Chihuahua, Mexico.

    Science.gov (United States)

    Villalba, L; Colmenero Sujo, L; Montero Cabrera, M E; Cano Jiménez, A; Rentería Villalobos, M; Delgado Mendoza, C J; Jurado Tenorio, L A; Dávila Rangel, I; Herrera Peraza, E F

    2005-01-01

    This paper reports (222)Rn concentrations in ground and drinking water of nine cities of Chihuahua State, Mexico. Fifty percent of the 114 sampled wells exhibited (222)Rn concentrations exceeding 11Bq/L, the maximum contaminant level (MCL) recommended by the USEPA. Furthermore, around 48% (123 samples) of the tap-water samples taken from 255 dwellings showed radon concentrations over the MCL. There is an apparent correlation between total dissolved solids and radon concentration in ground-water. The high levels of (222)Rn found may be entirely attributed to the nature of aquifer rocks.

  10. Maximum a posteriori Bayesian estimation of mycophenolic Acid area under the concentration-time curve: is this clinically useful for dosage prediction yet?

    Science.gov (United States)

    Staatz, Christine E; Tett, Susan E

    2011-12-01

    This review seeks to summarize the available data about Bayesian estimation of area under the plasma concentration-time curve (AUC) and dosage prediction for mycophenolic acid (MPA) and evaluate whether sufficient evidence is available for routine use of Bayesian dosage prediction in clinical practice. A literature search identified 14 studies that assessed the predictive performance of maximum a posteriori Bayesian estimation of MPA AUC and one report that retrospectively evaluated how closely dosage recommendations based on Bayesian forecasting achieved targeted MPA exposure. Studies to date have mostly been undertaken in renal transplant recipients, with limited investigation in patients treated with MPA for autoimmune disease or haematopoietic stem cell transplantation. All of these studies have involved use of the mycophenolate mofetil (MMF) formulation of MPA, rather than the enteric-coated mycophenolate sodium (EC-MPS) formulation. Bias associated with estimation of MPA AUC using Bayesian forecasting was generally less than 10%. However some difficulties with imprecision was evident, with values ranging from 4% to 34% (based on estimation involving two or more concentration measurements). Evaluation of whether MPA dosing decisions based on Bayesian forecasting (by the free website service https://pharmaco.chu-limoges.fr) achieved target drug exposure has only been undertaken once. When MMF dosage recommendations were applied by clinicians, a higher proportion (72-80%) of subsequent estimated MPA AUC values were within the 30-60 mg · h/L target range, compared with when dosage recommendations were not followed (only 39-57% within target range). Such findings provide evidence that Bayesian dosage prediction is clinically useful for achieving target MPA AUC. This study, however, was retrospective and focussed only on adult renal transplant recipients. Furthermore, in this study, Bayesian-generated AUC estimations and dosage predictions were not compared

  11. Radon concentrations in ground and drinking water in the state of Chihuahua, Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Villalba, L. [Centro de Investigacion en Materiales Avanzados, S.C., Miguel de Cervantes 120, Complejo Industrial Chihuahua, CP 31109 Chihuahua, Chih. (Mexico); Colmenero Sujo, L. [Centro de Investigacion en Materiales Avanzados, S.C., Miguel de Cervantes 120, Complejo Industrial Chihuahua, CP 31109 Chihuahua, Chih. (Mexico); Instituto Tecnologico de Chihuahua II, Ave. de las Industrias 11101, Chihuahua, Chih. (Mexico); Montero Cabrera, M.E. [Centro de Investigacion en Materiales Avanzados, S.C., Miguel de Cervantes 120, Complejo Industrial Chihuahua, CP 31109 Chihuahua, Chih. (Mexico)]. E-mail: elena.montero@cimav.edu.mx; Cano Jimenez, A. [Centro de Investigacion en Materiales Avanzados, S.C., Miguel de Cervantes 120, Complejo Industrial Chihuahua, CP 31109 Chihuahua, Chih. (Mexico); Renteria Villalobos, M. [Centro de Investigacion en Materiales Avanzados, S.C., Miguel de Cervantes 120, Complejo Industrial Chihuahua, CP 31109 Chihuahua, Chih. (Mexico); Delgado Mendoza, C.J. [Facultad de Ciencias Quimicas, Universidad Autonoma de Chihuahua, Ciudad Universitaria S/N, Chihuahua, Chih. (Mexico); Jurado Tenorio, L.A. [Facultad de Ciencias Quimicas, Universidad Autonoma de Chihuahua, Ciudad Universitaria S/N, Chihuahua, Chih. (Mexico); Davila Rangel, I. [Centro Regional de Estudios Nucleares, Universidad Autonoma de Zacatecas, Cipres 20, Zacatecas, Zac. (Mexico); Herrera Peraza, E.F. [Centro de Investigacion en Materiales Avanzados, S.C., Miguel de Cervantes 120, Complejo Industrial Chihuahua, CP 31109 Chihuahua, Chih. (Mexico)

    2005-07-01

    This paper reports {sup 222}Rn concentrations in ground and drinking water of nine cities of Chihuahua State, Mexico. Fifty percent of the 114 sampled wells exhibited {sup 222}Rn concentrations exceeding 11 Bq/L, the maximum contaminant level (MCL) recommended by the USEPA. Furthermore, around 48% (123 samples) of the tap-water samples taken from 255 dwellings showed radon concentrations over the MCL. There is an apparent correlation between total dissolved solids and radon concentration in ground-water. The high levels of {sup 222}Rn found may be entirely attributed to the nature of aquifer rocks.

  12. Radon Concentration in Outdoors and Indoors Around the Flare in Oil Mine Sites

    International Nuclear Information System (INIS)

    Sutarman; Wahyudi; Luhantara

    2003-01-01

    The flares are much found at the oil exploration areas which appear the combustion gases emission to the environment that pass through a pipe at about 8 m high from the ground level. The flare is released into the environment together with the hydrocarbon and radon gases. This study has been carried out the measurement of the radon gas concentration only. Radon is a radioactive gas which comes from the natural radioactive decay of uranium ( 238 U). The outdoor radon concentrations were measured in 23 locations with the two-filter method. The locations were determined by a circle which the flare as the point center. The outdoor radon concentrations were measured in 74 houses (more than distance of 600 m from the flare) with the alpha track detector (CR-39) placed in the living rooms for about three months. The measurements of the radon concentrations were carried out in Cepu, Cirebon, and Prabumulih oil mine sites. The results showed that the outdoor radon concentrations a range of 108 Bq/m 3 to 256 Bq/m 3 in Cepu, 248 Bq/m 3 to 3525 Bq/m 3 in Cirebon, and 51 Bq/m 3 to 114 Bq/m 3 in Prabumulih. The results showed that the indoor radon concentrations a range of 11 Bq/m 3 to 38 Bq/m 3 in Cepu, 28 Bq/m 3 to 184 Bq/m 3 in Cirebon, and 12 Bq/m 3 to 38 Bq/m 3 in Prabumulih. The data of the maximum radon concentration in outdoor air was higher than an actual level which recommended by International Atomic Energy Agency (IAEA) for workplaces. The maximum radon concentration in indoor air was lower than an actual level which recommended by IAEA for dwellings. IAEA recommends the actual level of 1000 Bq/m 3 for workplaces and 200 Bq/m 3 for dwellings. These data will be used for the baseline data of the environmental radioactivity in Indonesia. (author)

  13. 40 CFR Table C-1 to Subpart C of... - Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specification

    Science.gov (United States)

    2010-07-01

    ... Measurements Required, and Maximum Discrepancy Specification C Table C-1 to Subpart C of Part 53 Protection of... Reference Methods Pt. 53, Subpt. C, Table C-1 Table C-1 to Subpart C of Part 53—Test Concentration Ranges..., June 22, 2010, table C-1 to subpart C was revised, effective Aug. 23, 2010. For the convenience of the...

  14. Clustering recommendations to compute agent reputation

    Science.gov (United States)

    Bedi, Punam; Kaur, Harmeet

    2005-03-01

    Traditional centralized approaches to security are difficult to apply to multi-agent systems which are used nowadays in e-commerce applications. Developing a notion of trust that is based on the reputation of an agent can provide a softer notion of security that is sufficient for many multi-agent applications. Our paper proposes a mechanism for computing reputation of the trustee agent for use by the trustier agent. The trustier agent computes the reputation based on its own experience as well as the experience the peer agents have with the trustee agents. The trustier agents intentionally interact with the peer agents to get their experience information in the form of recommendations. We have also considered the case of unintentional encounters between the referee agents and the trustee agent, which can be directly between them or indirectly through a set of interacting agents. The clustering is done to filter off the noise in the recommendations in the form of outliers. The trustier agent clusters the recommendations received from referee agents on the basis of the distances between recommendations using the hierarchical agglomerative method. The dendogram hence obtained is cut at the required similarity level which restricts the maximum distance between any two recommendations within a cluster. The cluster with maximum number of elements denotes the views of the majority of recommenders. The center of this cluster represents the reputation of the trustee agent which can be computed using c-means algorithm.

  15. Concentration of Nitrate in Bottled Drinking Water in Qom, Iran

    Directory of Open Access Journals (Sweden)

    Mohammad Saberi Bidgoli

    2013-11-01

    Full Text Available Background & Aims of the Study: The global consumption of bottled water is growing with substantial growth in sales volumes on every continent. The highest growth rates are occurring in Asia and South America. Biological and chemical monitoring of these waters is necessary. The aim of current study was determination of nitrate concentration in bottled drinking water in Qom, Iran in 2012. Materials & Methods: A cross-sectional study carried out in Qom, Iran. First of all, 18 most frequent brands of bottled drinking waters were purchased in June 2012 randomly. Then concentration of nitrate was measured according to the spectrophotometric method. In next step, experiment data were analyzed by Excel Software and P value was obtained by statistical calculations. Finally data were comprised with written nitrate concentration on labels and recommended permissible values . Results: The median nitrate concentration was 2.1 mg/L with the minimum 0.8 mg/L and maximum 8.1 mg/L. In 66.7 % of the samples, the measured nitrate concentrations were less than the written nitrate concentrations and in 33.3% of samples, the nitrate concentration was higher. The statistical calculation proved the significant difference between the median of written nitrate concentration on the label and investigated nitrate concentration (P value > 0.05. Conclusions: It be concluded that the measured nitrate concentration in all of the water samples is below the recommended permissible level.

  16. Evaluation of performance and maximum length of continuous decks in bridges : part 1.

    Science.gov (United States)

    2011-06-01

    The purpose of this research was to evaluate the performance history of continuous bridge decks in the State of Georgia, to determine why the current design detail works, to recommend a new design detail, and to recommend the maximum and/or optimum l...

  17. Determination of the Lead, Cadmium, and Chromium Concentration in Mineral Feeds and Supplements for Cattle Produced in the Mato Grosso State, Brazil.

    Science.gov (United States)

    Sigarini, Keyla Dos Santos; de Oliveira, Adriana Paiva; Martins, Daiane Lima; Brasil, Alexandre Silva; de Oliveira, Kamila Cristina; Villa, Ricardo Dalla

    2017-05-01

    This work aimed to determine the concentration of lead (Pb), cadmium (Cd), and chromium (Cr) in mineral feeds and supplements for cattle produced in the Mato Grosso State, Brazil. Three different lots of nine mineral supplements and eleven mineral feeds were collected, and the samples were prepared by wet decomposition and quantified by flame atomic absorption spectrometry. The limits of detection and quantification ranged from 0.18 to 0.64 mg kg -1 and 0.54 to 1.94 mg kg -1 , respectively. Cr concentrations varied from lower than the LQI to 11.9 mg kg -1 , and all samples presented values below the maximum recommended by the National Research Council (NRC) and European Union (EU). Cd concentrations varied from lower than the LQI to 6.1 mg kg -1 , and 100 % of the mineral supplements and 60 % of the mineral feed showed Cd concentrations above the recommended by the EU (1.0 mg kg -1 ). Pb concentrations ranged from lower than the LQI to 33.1 mg kg -1 , and 100 % of the mineral supplements and 90 % of the mineral feed showed Pb concentrations above the recommended by the EU (5.0 mg kg -1 ). All samples presented values below the maximum recommended by the NRC for Cd and Pb (10 and 100 mg kg -1 , respectively). A large scatter of results was observed in the different samples for the three elements analyzed. This can be attributed to inhomogeneous impurity levels between batches of phosphate rocks used in the mineral feeds and supplements. A strict control of such mineral feeds and supplements should be implemented.

  18. Investigation levels of radioisotopes in the body and in urine consequences of the recent recommendations on the annual limits of intake

    International Nuclear Information System (INIS)

    Shamai, Y.; Tirkel, M.; Schlesinger, T.

    1980-01-01

    The recently presented recommendations of Committee 2 of the International Commission on Radiological Protection (ICRP) concerning annual limits of intake (ALI) for workers differ in many cases from the maximum permissible annual intake (MPAI) previously recommended. The new recommendations directly influence the derived health physics parameters, such as the acceptable body burden and concentration of radioisotopes in the urine. The investigation level at any time after intake was defined as the concentration of activity in the urine arising from an intake of 1/20 of an ALI. An analogous definition is used for the total body investigation level. A computer code was written which calculates the investigation levels in the body and urine. Results are given for some commonly used radioisotopes, as a function of time after ingestion. From these investigation levels it is possible to calculate the levels in urine and the body arising from an intake that corresponds to a particular committed dose. (H.K.)

  19. Patch test concentrations (doses in mg/cm2 ) for the 12 non-mix fragrance substances regulated by European legislation.

    Science.gov (United States)

    Bruze, Magnus; Svedman, Cecilia; Andersen, Klaus Ejner; Bruynzeel, Derk; Goossens, An; Johansen, Jeanne Duus; Matura, Mihaly; Orton, David; Vigan, Martine

    2012-03-01

    According to EU legislation, 26 fragrance substance allergens must be labelled on cosmetic products. For 12 of them, the optimal patch test concentration/dose has not been evaluated. To establish the optimal patch test doses in mg/cm2 for the 12 fragrance substances that are not included in fragrance mix I or II in the European baseline patch test series. Patch testing with the 12 fragrance substances was performed in a stepwise manner encompassing up to five rounds in at least 100 dermatitis patients for each round. Before patch testing, an individual maximum concentration/dose was determined for each fragrance substance. The predetermined maximum patch test concentrations/doses could be tested for all 12 fragrance substances, with no observable adverse reactions being noted. For each fragrance substance investigated, it is recommended that half of the maximum patch test dose (mg/cm2) be used for aimed and screening patch testing. © 2012 John Wiley & Sons A/S.

  20. Contribution to the study of maximum levels for liquid radioactive waste disposal into continental and sea water. Treatment of some typical samples

    International Nuclear Information System (INIS)

    Bittel, R.; Mancel, J.

    1968-10-01

    The most important carriers of radioactive contamination of man are the whole of foodstuffs and not only ingested water or inhaled air. That is the reason why, in accordance with the spirit of the recent recommendations of the ICRP, it is proposed to substitute the idea of maximum levels of contamination of water to the MPC. In the case of aquatic food chains (aquatic organisms and irrigated foodstuffs), the knowledge of the ingested quantities and of the concentration factors food/water permit to determinate these maximum levels, or to find out a linear relation between the maximum levels in the case of two primary carriers of contamination (continental and sea waters). The notion of critical food-consumption, critical radioelements and formula of waste disposal are considered in the same way, taking care to attach the greatest possible importance to local situations. (authors) [fr

  1. Maximum permissible concentration of radon {sup 222}Rn in air; La concentration maximale admissible du radon 222 dans l'air

    Energy Technology Data Exchange (ETDEWEB)

    Hamard, J; Beau, P G; Ergas, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires, departement de la protection sanitaire, service d' hygiene atomique

    1968-09-01

    In order to verify the validity of the values proposed for the maximum permissible concentration of {sup 222}Rn in air, one can either approach the problem: - by epidemiological studies tending to determine the relation dose-effect both quantitatively and qualitatively; - or by choosing a lung model and clearance constants allowing a more accurate determination of the delivered dose and the localisation of the more severely irradiated portions of the bronchial tree. The radon MPC have been calculated using the model and the respiration constants set up by the I.C.R.P. Task Group on Lung dynamics. Two cases have been considered, i.e. when the radon daughter products behave as soluble materials and as insoluble ones. The values which have been found have been compared with those given up to now by several national and international bodies. (authors) [French] Deux voies d'approche peuvent etre empruntees pour verifier la validite des valeurs proposees pour la concentration maximale admissible du radon 222 dans l'air: - etudes epidemiologiques tendant a preciser qualitativement et quantitativement la relation dose-effet; - choix d'un modele pulmonaire et de constantes d'epuration permettant une determination plus precise de la dose delivree et la localisation des segments de l'arbre pulmonaire les plus irradies. Les auteurs ont utilise pour le calcul de la CMA du radon le modele et les constantes respiratoires proposees par le Task Group on Lungs dynamics de la C.I.P.R. On a pris en consideration le cas ou les descendants du radon se comportent comme des substances solubles et celui ou ils se comportent comme des substances insolubles. Les valeurs trouvees sont comparees a celles proposees jusqu'alors par divers organismes nationaux et internationaux. (auteurs)

  2. Effect of Chinese traditional medicine anti-fatigue prescription on the concentration of the serum testosterone and cortisol in male rats under stress of maximum intensive training

    International Nuclear Information System (INIS)

    Dong Ling; Si Xulan

    2008-01-01

    Objective: To study the effect of chinese traditional medicine anti-fatigue prescription on the concentration of the serum testosterone (T) and cortisol (C) in male rats under the stress of maximum intensive training. Methods: Wistar male rat models of stress under maximum intensity training were established (n=40) and half of them were treated with Chinese traditional medicine anti-fatigue prescription twenty undisturbed rats served as controls. Testosterone and cortisol serum levels were determined with RIA at the end of the seven weeks' experiment. Results: Maximum intensive training would cause the level of the serum testosterone lowered, the concentration of the cortisol elevated and the ratio of T/C reduced. The serum T levels and T/C ratio were significantly lower and cortisol levels significantly higher in the untreated models than those in the treated models and controls (P<0.01). The levels of the two hormones were markedly corrected in the treated models with no significantly differences from those in the controls. However, the T/C ratio was still significantly lower than that in the controls (P <0.05) due to a relatively slightly greater degree of reduction of T levels. Conclusion: Anti-fatigue prescription can not only promote the recovery of fatigue after the maximum intensive training but also strengthen the anabolism of the rats. (authors)

  3. Determination of radon concentration in drinking water resources of villages nearby Lalehzar fault and evaluation the annual effective dose

    International Nuclear Information System (INIS)

    Mohammad Malakootian; Zahra Darabi Fard; Mojtaba Rahimi

    2015-01-01

    The radon concentration has been measured in 44 drinking water resources, in villages nearby Lalehzar fault in winter 2014. Some samples showed a higher concentration of radon surpassing limit set by EPA. Further, a sample was taken from water distribution networks for these sources of water. Soluble radon concentration was measured by RAD7 device. Range radon concentration was 26.88 and 0.74 BqL -1 respectively. The maximum and minimum annual effective dose for adults was estimated at 52.7 and 2.29 µSvY -1 , respectively. Reducing radon from water before use is recommended to improve public health. (author)

  4. Stocking and structure for maximum growth in sugar maple selection stands.

    Science.gov (United States)

    Thomas R. Crow; Carl H. Tubbs; Rodney D. Jacobs; Robert R. Oberg

    1981-01-01

    The impacts of stocking, structure, and cutting cycle on basal area, cubic foot volume, board foot volume, and diameter growth are considered. Recommendations are provided for maximum growth in uneven-aged sugar maple stands.

  5. MAK and BAT values list 2017. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2017. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2017-08-01

    The MAK and BAT values list 2017 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

  6. Spatiotemporal modeling of PM2.5 concentrations at the national scale combining land use regression and Bayesian maximum entropy in China.

    Science.gov (United States)

    Chen, Li; Gao, Shuang; Zhang, Hui; Sun, Yanling; Ma, Zhenxing; Vedal, Sverre; Mao, Jian; Bai, Zhipeng

    2018-05-03

    Concentrations of particulate matter with aerodynamic diameter Bayesian Maximum Entropy (BME) interpolation of the LUR space-time residuals were developed to estimate the PM 2.5 concentrations on a national scale in China. This hybrid model could potentially provide more valid predictions than a commonly-used LUR model. The LUR/BME model had good performance characteristics, with R 2  = 0.82 and root mean square error (RMSE) of 4.6 μg/m 3 . Prediction errors of the LUR/BME model were reduced by incorporating soft data accounting for data uncertainty, with the R 2 increasing by 6%. The performance of LUR/BME is better than OK/BME. The LUR/BME model is the most accurate fine spatial scale PM 2.5 model developed to date for China. Copyright © 2018. Published by Elsevier Ltd.

  7. Announcement of recommendations issued by the German Radiation Protection Commission (Strahlenschutzkommission) - radiation protection for the use of drinking water supplies from uranium mining areas

    International Nuclear Information System (INIS)

    1993-01-01

    The recommendations issued by the German Radiation Protection Commission demand analyses of the activities of natural uranium, radium 226 and lead 210 in drinking water. The concentrations of lead 210 and polonium 210 are assumed to be balanced. The conditions for observation of the maximum permissible activities are given. The activities of radium 228 and radium 224 must be determined and be taken into account. (orig.) [de

  8. Selection of suitable mineral acid and its concentration for biphasic dilute acid hydrolysis of the sodium dithionite delignified Prosopis juliflora to hydrolyze maximum holocellulose.

    Science.gov (United States)

    Naseeruddin, Shaik; Desai, Suseelendra; Venkateswar Rao, L

    2016-02-01

    Two grams of delignified substrate at 10% (w/v) level was subjected to biphasic dilute acid hydrolysis using phosphoric acid, hydrochloric acid and sulfuric acid separately at 110 °C for 10 min in phase-I and 121 °C for 15 min in phase-II. Combinations of acid concentrations in two phases were varied for maximum holocellulose hydrolysis with release of fewer inhibitors, to select the suitable acid and its concentration. Among three acids, sulfuric acid in combination of 1 & 2% (v/v) hydrolyzed maximum holocellulose of 25.44±0.44% releasing 0.51±0.02 g/L of phenolics and 0.12±0.002 g/L of furans, respectively. Further, hydrolysis of delignified substrate using selected acid by varying reaction time and temperature hydrolyzed 55.58±1.78% of holocellulose releasing 2.11±0.07 g/L and 1.37±0.03 g/L of phenolics and furans, respectively at conditions of 110 °C for 45 min in phase-I & 121 °C for 60 min in phase-II. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Project Opalinus Clay: Radionuclide Concentration Limits in the Cementitious Near-Field of an ILW Repository

    International Nuclear Information System (INIS)

    Berner, U.

    2003-05-01

    The disposal feasibility study currently performed by Nagra includes a succession of quantitative models, aiming at describing the fate of radionuclides potentially escaping from the repository system. In this chain of models the present report provides the so called 'solubility limits' (maximum expected concentrations) for safety relevant radionuclides from ILW wastes, disposed of in a chemically reducing, cementitious environment. From a chemical point of view, the pore waters of hydrated cement matrices provide an exceptional environment. Compared with usual ground waters exhibiting pH-values of around 8, cement pore waters are strongly alkaline with pH-values from 12.5 to 13.5 and contain nearly no carbonate and only little sulfate. Oxides and hydroxides mainly determine solubility and speciation of the elements. Solubility and speciation calculations in cementitious pore waters were performed using the very recently updated Nagra/PSI Chemical Thermodynamic Data Base (TDB) for the majority of the 36 elements addressed as potentially relevant. Wherever possible, maximum concentrations compiled in this report were based on geochemical calculations. In order to ensure full traceability, all thermodynamic data not included in the TDB are explicitly specified in the document. For similar reasons the compilation of results (Table 1) clearly distinguishes between calculated and recommended items. The heading 'CALCULATED' lists maximum concentrations based on data fully documented in the TDB; results under the heading 'RECOMMENDED' include data from other sources. The pH sensitivity of the results was examined by performing calculations at pH 13.4, in accordance with the pH of non-altered cement pore water. Solubility increases predominantly for elements that tend to form anionic hydroxide complexes (Sn, Pd, Zr, Ni, Eu, Cd, Mo, Co). Oxidizing conditions around +350 mV might be expected in the environment of nitrate-containing wastes. In this case, significant

  10. Project Opalinus Clay: Radionuclide Concentration Limits in the Cementitious Near-Field of an ILW Repository

    Energy Technology Data Exchange (ETDEWEB)

    Berner, U

    2003-05-01

    The disposal feasibility study currently performed by Nagra includes a succession of quantitative models, aiming at describing the fate of radionuclides potentially escaping from the repository system. In this chain of models the present report provides the so called 'solubility limits' (maximum expected concentrations) for safety relevant radionuclides from ILW wastes, disposed of in a chemically reducing, cementitious environment. From a chemical point of view, the pore waters of hydrated cement matrices provide an exceptional environment. Compared with usual ground waters exhibiting pH-values of around 8, cement pore waters are strongly alkaline with pH-values from 12.5 to 13.5 and contain nearly no carbonate and only little sulfate. Oxides and hydroxides mainly determine solubility and speciation of the elements. Solubility and speciation calculations in cementitious pore waters were performed using the very recently updated Nagra/PSI Chemical Thermodynamic Data Base (TDB) for the majority of the 36 elements addressed as potentially relevant. Wherever possible, maximum concentrations compiled in this report were based on geochemical calculations. In order to ensure full traceability, all thermodynamic data not included in the TDB are explicitly specified in the document. For similar reasons the compilation of results (Table 1) clearly distinguishes between calculated and recommended items. The heading 'CALCULATED' lists maximum concentrations based on data fully documented in the TDB; results under the heading 'RECOMMENDED' include data from other sources. The pH sensitivity of the results was examined by performing calculations at pH 13.4, in accordance with the pH of non-altered cement pore water. Solubility increases predominantly for elements that tend to form anionic hydroxide complexes (Sn, Pd, Zr, Ni, Eu, Cd, Mo, Co). Oxidizing conditions around +350 mV might be expected in the environment of nitrate-containing wastes. In

  11. A conductance maximum observed in an inward-rectifier potassium channel

    OpenAIRE

    1994-01-01

    One prediction of a multi-ion pore is that its conductance should reach a maximum and then begin to decrease as the concentration of permeant ion is raised equally on both sides of the membrane. A conductance maximum has been observed at the single-channel level in gramicidin and in a Ca(2+)-activated K+ channel at extremely high ion concentration (> 1,000 mM) (Hladky, S. B., and D. A. Haydon. 1972. Biochimica et Biophysica Acta. 274:294-312; Eisenmam, G., J. Sandblom, and E. Neher. 1977. In ...

  12. MAK and BAT values list 2015. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2015. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2015-11-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2015 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  13. MAK and BAT values list 2014. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2014. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-11-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2014 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  14. MAK and BAT values list 2013. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2013. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2013 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  15. Pushing concentration of stationary solar concentrators to the limit.

    Science.gov (United States)

    Winston, Roland; Zhang, Weiya

    2010-04-26

    We give the theoretical limit of concentration allowed by nonimaging optics for stationary solar concentrators after reviewing sun- earth geometry in direction cosine space. We then discuss the design principles that we follow to approach the maximum concentration along with examples including a hollow CPC trough, a dielectric CPC trough, and a 3D dielectric stationary solar concentrator which concentrates sun light four times (4x), eight hours per day year around.

  16. Effects of high salinity from desalination brine on growth, photosynthesis, water relations and osmolyte concentrations of seagrass Posidonia australis.

    Science.gov (United States)

    Cambridge, M L; Zavala-Perez, A; Cawthray, G R; Mondon, J; Kendrick, G A

    2017-02-15

    Highly saline brines from desalination plants expose seagrass communities to salt stress. We examined effects of raised salinity (46 and 54psu) compared with seawater controls (37psu) over 6weeks on the seagrass, Posidonia australis, growing in tanks with the aim of separating effects of salinity from other potentially deleterious components of brine and determining appropriate bioindicators. Plants survived exposures of 2-4weeks at 54psu, the maximum salinity of brine released from a nearby desalination plant. Salinity significantly reduced maximum quantum yield of PSII (chlorophyll a fluorescence emissions). Leaf water potential (Ψ w ) and osmotic potential (Ψ π ) were more negative at increased salinity, while turgor pressure (Ψ p ) was unaffected. Leaf concentrations of K + and Ca 2+ decreased, whereas concentrations of sugars (mainly sucrose) and amino acids increased. We recommend leaf osmolarity, ion, sugar and amino acid concentrations as bioindicators for salinity effects, associated with brine released in desalination plant outfalls. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. maximum neutron flux at thermal nuclear reactors

    International Nuclear Information System (INIS)

    Strugar, P.

    1968-10-01

    Since actual research reactors are technically complicated and expensive facilities it is important to achieve savings by appropriate reactor lattice configurations. There is a number of papers, and practical examples of reactors with central reflector, dealing with spatial distribution of fuel elements which would result in higher neutron flux. Common disadvantage of all the solutions is that the choice of best solution is done starting from the anticipated spatial distributions of fuel elements. The weakness of these approaches is lack of defined optimization criteria. Direct approach is defined as follows: determine the spatial distribution of fuel concentration starting from the condition of maximum neutron flux by fulfilling the thermal constraints. Thus the problem of determining the maximum neutron flux is solving a variational problem which is beyond the possibilities of classical variational calculation. This variational problem has been successfully solved by applying the maximum principle of Pontrjagin. Optimum distribution of fuel concentration was obtained in explicit analytical form. Thus, spatial distribution of the neutron flux and critical dimensions of quite complex reactor system are calculated in a relatively simple way. In addition to the fact that the results are innovative this approach is interesting because of the optimization procedure itself [sr

  18. RA-226 concentration in water samples near uranium mines and in marine fishes

    International Nuclear Information System (INIS)

    Porntepkasemsan, B.

    1987-11-01

    Radium-226 and calcium were measured in water samples from the vicinity of three uranium mines and in fish samples collected from Puget sound, Washington State. The radium content of the samples were below the maximum permissible concentration 3 pCi/L for drinking water recommended by the Public Health Service and U.S. Environmental Protection Agency. The mean value of Ra-226 in water was 0.428 pCi/L and ranged from 0.043 to 1.552 pCi/L, whereas calcium content ranged from 3.0 to 190.0 mg/L. Ra-226 concentrations and calcium content in whole fish were 0.833-20.328 pCi/kg wet wt. and 114.1-259.3 mg/g ash, respectively. Results of the study indicated that Ra-226 concentration in water was correlated with calcium concentration but that this correlation was not observed in fish sample except English sole

  19. Maximum neutron flux in thermal reactors; Maksimum neutronskog fluksa kod termalnih reaktora

    Energy Technology Data Exchange (ETDEWEB)

    Strugar, P V [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Yugoslavia)

    1968-07-01

    Direct approach to the problem is to calculate spatial distribution of fuel concentration if the reactor core directly using the condition of maximum neutron flux and comply with thermal limitations. This paper proved that the problem can be solved by applying the variational calculus, i.e. by using the maximum principle of Pontryagin. Mathematical model of reactor core is based on the two-group neutron diffusion theory with some simplifications which make it appropriate from maximum principle point of view. Here applied theory of maximum principle are suitable for application. The solution of optimum distribution of fuel concentration in the reactor core is obtained in explicit analytical form. The reactor critical dimensions are roots of a system of nonlinear equations and verification of optimum conditions can be done only for specific examples.

  20. Study of radon concentration and toxic elements in drinking and irrigated water and its implications in Sungai Petani, Kedah, Malaysia

    Directory of Open Access Journals (Sweden)

    Nisar Ahmad

    2015-07-01

    Full Text Available The radon activity concentration and toxic elements have been assessed in drinking and irrigated water samples collected from different locations of Sungai Petani, Kedah, Malaysia. The water samples were collected from wells, streams and taps. A calibrated alpha spectrometer RAD-7 (Model 2890 and Atomic Absorption Spectrometers (Perkin–Elmer, Model AAnalyst 200, Shimadzu, Model AA-700 were used to estimate radon activity concentration and toxic elements, respectively. Maximum average value of radon concentration among the various types of water sources was found 14.7 ± 1.44 Bq/l in well water used for drinking and irrigation and minimum was found 5.37 ± 0.58 Bq/l in tap water used for drinking. Contribution of radon in drinking water to indoor air and age dependent associated annual effective doses were calculated from the measured radon concentration and were found less than lower limit of recommended action level. The activity concentrations of Ni > Pb > Cd > As > Cr were found higher for streams water as compared to wells and tap water. Values of radon concentration in well water were found higher than EPA recommended level and lower than WHO action level while the annual effective doses and level of toxic elements in water reported in this study were found lower than recommended level.

  1. Rectangular maximum-volume submatrices and their applications

    KAUST Repository

    Mikhalev, Aleksandr; Oseledets, I.V.

    2017-01-01

    We introduce a definition of the volume of a general rectangular matrix, which is equivalent to an absolute value of the determinant for square matrices. We generalize results of square maximum-volume submatrices to the rectangular case, show a connection of the rectangular volume with an optimal experimental design and provide estimates for a growth of coefficients and an approximation error in spectral and Chebyshev norms. Three promising applications of such submatrices are presented: recommender systems, finding maximal elements in low-rank matrices and preconditioning of overdetermined linear systems. The code is available online.

  2. Maximum entropy method in momentum density reconstruction

    International Nuclear Information System (INIS)

    Dobrzynski, L.; Holas, A.

    1997-01-01

    The Maximum Entropy Method (MEM) is applied to the reconstruction of the 3-dimensional electron momentum density distributions observed through the set of Compton profiles measured along various crystallographic directions. It is shown that the reconstruction of electron momentum density may be reliably carried out with the aid of simple iterative algorithm suggested originally by Collins. A number of distributions has been simulated in order to check the performance of MEM. It is shown that MEM can be recommended as a model-free approach. (author). 13 refs, 1 fig

  3. Rectangular maximum-volume submatrices and their applications

    KAUST Repository

    Mikhalev, Aleksandr

    2017-10-18

    We introduce a definition of the volume of a general rectangular matrix, which is equivalent to an absolute value of the determinant for square matrices. We generalize results of square maximum-volume submatrices to the rectangular case, show a connection of the rectangular volume with an optimal experimental design and provide estimates for a growth of coefficients and an approximation error in spectral and Chebyshev norms. Three promising applications of such submatrices are presented: recommender systems, finding maximal elements in low-rank matrices and preconditioning of overdetermined linear systems. The code is available online.

  4. Radioactivity concentrations in common brands of cement in Nigeria

    International Nuclear Information System (INIS)

    Farai, I.P.; Ejeh, J.E.

    2006-01-01

    Radioactivity concentrations of 238 U, 232 Th and 40 K in common brands of Portland cement in Nigeria have been measured using a shielded 7.6 cm x 7.6 cm NaI(Tl) detector coupled to a Canberra series 10 plus multichannel analyzer. The cement samples show significant spread in their radioactivity concentrations, even among samples of the same brand. The weighted means of the activity concentrations of 238 U, 232 Th and 40 K in the different brands were 52.4, 4.1 and 91.8 Bq/kg, respectively. The radium equivalent ranged between 29.1 and 128.1 Bq/kg with a weighted mean value of 68.5 Bq/kg. The values are lower than corresponding values in cement samples in most other countries as contained in recent publications. They are also lower than the UNSCEAR recommended maximum of 370 Bq/kg. The safety criteria developed by ITB Poland for radioactivity in building materials, especially for radon build-up in homes were however, exceeded in some of the cement samples. (authors)

  5. Recommended well drilling and testing program

    International Nuclear Information System (INIS)

    Long, J.; Wilson, C.

    1978-07-01

    A well drilling and testing program is recommended by Lawrence Berkeley Laboratory to identify the hydrology of deep basalts in the Pasco Basin. The ultimate objective of this program is to assist in determining the feasibility of locating a nuclear waste repository on the Hanford Reservation. The recommended program has been staged for maximum effectiveness. In the first stage, six wells have been identified for drilling and testing which, when coupled with existing wells, will provide sufficient data for a preliminary overview of basin hydrology and a preliminary determination of the hydrologic suitability of the deep basalt for a repository site. The rate at which the first stage wells are drilled and tested will depend upon the date at which a preliminary determination of site suitability is required. It was assumed that a preliminary determination of suitability would be required in 1980, in which case all six first stage wells would be drilled in FY 1979. If the results of the first stage analysis are favorable for repository siting, tentative repository sites can be identified and a second stage hydrology program can be implemented to provide the necessary details of the flow system. To accomplish this stage, a number of deep wells would be required at locations both inside and outside the basin, with specific sites to be identified as the work progresses to obtain maximum utility of existing data. A program is recommended for testing in each new well and for completion of testing in each existing well. Recommended tests include borehole geophysics, pressure and permeability testing, geochemical sampling, tracer testing, hydrofracturing and borehole fracture logging. The entire data collection program is oriented toward providing the information required to establish and verify an accurate numerical model of the Pasco Basin

  6. Max '91: Flare research at the next solar maximum

    Science.gov (United States)

    Dennis, Brian; Canfield, Richard; Bruner, Marilyn; Emslie, Gordon; Hildner, Ernest; Hudson, Hugh; Hurford, Gordon; Lin, Robert; Novick, Robert; Tarbell, Ted

    1988-01-01

    To address the central scientific questions surrounding solar flares, coordinated observations of electromagnetic radiation and energetic particles must be made from spacecraft, balloons, rockets, and ground-based observatories. A program to enhance capabilities in these areas in preparation for the next solar maximum in 1991 is recommended. The major scientific issues are described, and required observations and coordination of observations and analyses are detailed. A program plan and conceptual budgets are provided.

  7. Max '91: flare research at the next solar maximum

    International Nuclear Information System (INIS)

    Dennis, B.; Canfield, R.; Bruner, M.

    1988-01-01

    To address the central scientific questions surrounding solar flares, coordinated observations of electromagnetic radiation and energetic particles must be made from spacecraft, balloons, rockets, and ground-based observatories. A program to enhance capabilities in these areas in preparation for the next solar maximum in 1991 is recommended. The major scientific issues are described, and required observations and coordination of observations and analyses are detailed. A program plan and conceptual budgets are provided

  8. Measurements of Indoor Radon Concentrations in Chaiya and Tha Chana Districts, Surat Thani Province, Thailand

    International Nuclear Information System (INIS)

    Titipornpun, K.; Titipornpun, A.; Sola, P.; Bhongsuwan, T.

    2014-01-01

    Chaiya and Tha Chana districts of Surat Thani province are located in the areas with high equivalent uranium at ground surface, which have been identified as sources of radon. A survey measurement of indoor radon concentrations was carried out in 248 houses, using CR-39 detectors in closed cups. All of the detectors were exposed to radon for forty days. After the exposure, the alpha tracks were made visible by chemical etching and counted manually under an optical microscope. The indoor concentrations in Chaiya district were found to vary from the minimum to the maximum of 4 Bq.m -3 to 88 Bq.m -3 , respectively. In Tha Chana district, the concentrations of indoor radon were varied from the minimum of 4 Bq.m -3 to the maximum of 159 Bq.m -3 . The geometric mean of indoor radon concentrations in Chaya and Tha Chana districts were found to be 26±2 Bq.m -3 and 30±2 Bq.m -3 , respectively. The overall geometric mean in the surveyed areas was 28±2 Bq.m -3 . Only in two houses (1%), the concentrations (151 and 159 Bq.m -3 ) were found to be higher than the action level recommended by the US EPA (148 Bq.m -3 ). Most houses (94%) have natural ventilation by keeping doors and windows opened during the daytime. This ventilation likely causes the low level of indoor radon concentrations.

  9. Recommendations for computer modeling codes to support the UMTRA groundwater restoration project

    Energy Technology Data Exchange (ETDEWEB)

    Tucker, M.D. [Sandia National Labs., Albuquerque, NM (United States); Khan, M.A. [IT Corp., Albuquerque, NM (United States)

    1996-04-01

    The Uranium Mill Tailings Remediation Action (UMTRA) Project is responsible for the assessment and remedial action at the 24 former uranium mill tailings sites located in the US. The surface restoration phase, which includes containment and stabilization of the abandoned uranium mill tailings piles, has a specific termination date and is nearing completion. Therefore, attention has now turned to the groundwater restoration phase, which began in 1991. Regulated constituents in groundwater whose concentrations or activities exceed maximum contaminant levels (MCLs) or background levels at one or more sites include, but are not limited to, uranium, selenium, arsenic, molybdenum, nitrate, gross alpha, radium-226 and radium-228. The purpose of this report is to recommend computer codes that can be used to assist the UMTRA groundwater restoration effort. The report includes a survey of applicable codes in each of the following areas: (1) groundwater flow and contaminant transport modeling codes, (2) hydrogeochemical modeling codes, (3) pump and treat optimization codes, and (4) decision support tools. Following the survey of the applicable codes, specific codes that can best meet the needs of the UMTRA groundwater restoration program in each of the four areas are recommended.

  10. Recommendations for computer modeling codes to support the UMTRA groundwater restoration project

    International Nuclear Information System (INIS)

    Tucker, M.D.; Khan, M.A.

    1996-04-01

    The Uranium Mill Tailings Remediation Action (UMTRA) Project is responsible for the assessment and remedial action at the 24 former uranium mill tailings sites located in the US. The surface restoration phase, which includes containment and stabilization of the abandoned uranium mill tailings piles, has a specific termination date and is nearing completion. Therefore, attention has now turned to the groundwater restoration phase, which began in 1991. Regulated constituents in groundwater whose concentrations or activities exceed maximum contaminant levels (MCLs) or background levels at one or more sites include, but are not limited to, uranium, selenium, arsenic, molybdenum, nitrate, gross alpha, radium-226 and radium-228. The purpose of this report is to recommend computer codes that can be used to assist the UMTRA groundwater restoration effort. The report includes a survey of applicable codes in each of the following areas: (1) groundwater flow and contaminant transport modeling codes, (2) hydrogeochemical modeling codes, (3) pump and treat optimization codes, and (4) decision support tools. Following the survey of the applicable codes, specific codes that can best meet the needs of the UMTRA groundwater restoration program in each of the four areas are recommended

  11. Spatio-temporal observations of the tertiary ozone maximum

    Directory of Open Access Journals (Sweden)

    V. F. Sofieva

    2009-07-01

    Full Text Available We present spatio-temporal distributions of the tertiary ozone maximum (TOM, based on GOMOS (Global Ozone Monitoring by Occultation of Stars ozone measurements in 2002–2006. The tertiary ozone maximum is typically observed in the high-latitude winter mesosphere at an altitude of ~72 km. Although the explanation for this phenomenon has been found recently – low concentrations of odd-hydrogen cause the subsequent decrease in odd-oxygen losses – models have had significant deviations from existing observations until recently. Good coverage of polar night regions by GOMOS data has allowed for the first time to obtain spatial and temporal observational distributions of night-time ozone mixing ratio in the mesosphere.

    The distributions obtained from GOMOS data have specific features, which are variable from year to year. In particular, due to a long lifetime of ozone in polar night conditions, the downward transport of polar air by the meridional circulation is clearly observed in the tertiary ozone maximum time series. Although the maximum tertiary ozone mixing ratio is achieved close to the polar night terminator (as predicted by the theory, TOM can be observed also at very high latitudes, not only in the beginning and at the end, but also in the middle of winter. We have compared the observational spatio-temporal distributions of the tertiary ozone maximum with that obtained using WACCM (Whole Atmosphere Community Climate Model and found that the specific features are reproduced satisfactorily by the model.

    Since ozone in the mesosphere is very sensitive to HOx concentrations, energetic particle precipitation can significantly modify the shape of the ozone profiles. In particular, GOMOS observations have shown that the tertiary ozone maximum was temporarily destroyed during the January 2005 and December 2006 solar proton events as a result of the HOx enhancement from the increased ionization.

  12. Parametric characteristics of a solar thermophotovoltaic system at the maximum efficiency

    International Nuclear Information System (INIS)

    Liao, Tianjun; Chen, Xiaohang; Yang, Zhimin; Lin, Bihong; Chen, Jincan

    2016-01-01

    Graphical abstract: A model of the far-field TPVC driven by solar energy, which consists of an optical concentrator, an absorber, an emitter, and a PV cell and is simply referred as to the far-field STPVS. - Highlights: • A model of the far-field solar thermophotovoltaic system (STPVS) is established. • External and internal irreversible losses are considered. • The maximum efficiency of the STPVS is calculated. • Optimal values of key parameters at the maximum efficiency are determined. • Effects of the concentrator factor on the performance of the system are discussed. - Abstract: A model of the solar thermophotovoltaic system (STPVS) consisting of an optical concentrator, a thermal absorber, an emitter, and a photovoltaic (PV) cell is proposed, where the far-field thermal emission between the emitter and the PV cell, the radiation losses from the absorber and emitter to the environment, the reflected loss from the absorber, and the finite-rate heat exchange between the PV cell and the environment are taken into account. Analytical expressions for the power output of and overall efficiency of the STPVS are derived. By solving thermal equilibrium equations, the operating temperatures of the emitter and PV cell are determined and the maximum efficiency of the system is calculated numerically for given values of the output voltage of the PV cell and the ratio of the front surface area of the absorber to that of the emitter. For different bandgaps, the maximum efficiencies of the system are calculated and the corresponding optimum values of several operating parameters are obtained. The effects of the concentrator factor on the optimum performance of the system are also discussed.

  13. Maximum entropy decomposition of quadrupole mass spectra

    International Nuclear Information System (INIS)

    Toussaint, U. von; Dose, V.; Golan, A.

    2004-01-01

    We present an information-theoretic method called generalized maximum entropy (GME) for decomposing mass spectra of gas mixtures from noisy measurements. In this GME approach to the noisy, underdetermined inverse problem, the joint entropies of concentration, cracking, and noise probabilities are maximized subject to the measured data. This provides a robust estimation for the unknown cracking patterns and the concentrations of the contributing molecules. The method is applied to mass spectroscopic data of hydrocarbons, and the estimates are compared with those received from a Bayesian approach. We show that the GME method is efficient and is computationally fast

  14. Efficiency of autonomous soft nanomachines at maximum power.

    Science.gov (United States)

    Seifert, Udo

    2011-01-14

    We consider nanosized artificial or biological machines working in steady state enforced by imposing nonequilibrium concentrations of solutes or by applying external forces, torques, or electric fields. For unicyclic and strongly coupled multicyclic machines, efficiency at maximum power is not bounded by the linear response value 1/2. For strong driving, it can even approach the thermodynamic limit 1. Quite generally, such machines fall into three different classes characterized, respectively, as "strong and efficient," "strong and inefficient," and "balanced." For weakly coupled multicyclic machines, efficiency at maximum power has lost any universality even in the linear response regime.

  15. Determination of radon activity concentration in drinking water and evaluation of the annual effective dose in Hassan district, Karnataka state, India

    International Nuclear Information System (INIS)

    Srinivasa, E.; Rangaswamy, D.R.; Sannappa, J.

    2015-01-01

    The radon concentration has been determined in 27 drinking water samples of Hassan district and was estimated by using emanometry technique and physicochemical parameters were estimated using standard techniques. The 222 Rn concentrations in water are varying from 0.85 ± 0.2 to 60.74 ± 2.5 Bq l -1 with an average value of 26.5 ± 1.65 Bq l -1 . This study reveals that 66 % of the drinking water samples have radon concentration level in excess of the EPA recommended maximum contamination level of 11.1 Bq l -1 . There is no significant correlation noted between radon concentration and physicochemical parameters. The mean annual effective ingestion doses received from all samples are lower than 0.1 mSv y -1 . (author)

  16. Secondary poisoning of cadmium, copper and mercury: implications for the Maximum Permissible Concentrations and Negligible Concentrations in water, sediment and soil

    NARCIS (Netherlands)

    Smit CE; van Wezel AP; Jager T; Traas TP; CSR

    2000-01-01

    De betekenis van doorvergiftiging voor de Maximum Toelaatbaar Risiconiveau's (MTRs) en Verwaarloosbaar Risiconiveau's (VRs) van cadmium, koper en kwik in water, sediment en bodem is geevalueerd. Veldgegevens met betrekking tot de accumulatie van deze elementen door vissen, mosselen en

  17. Radon Concentration in Outdoors and Indoors Around the Flare in Oil Mine Sites; Konsentrasi Gas Radon di Udara di Luar dan Dalam Rumah Sekitar Nyala-api Kawasan Tambang Minyak

    Energy Technology Data Exchange (ETDEWEB)

    Sutarman,; Wahyudi, [Centre for Research and Development of Radiation Safety and Nuclear Biomedicine, National Nuclear Energy Agency, Jakarta (Indonesia); Luhantara, [University of Indonesia, Jakarta (Indonesia)

    2003-03-15

    The flares are much found at the oil exploration areas which appear the combustion gases emission to the environment that pass through a pipe at about 8 m high from the ground level. The flare is released into the environment together with the hydrocarbon and radon gases. This study has been carried out the measurement of the radon gas concentration only. Radon is a radioactive gas which comes from the natural radioactive decay of uranium ({sup 238}U). The outdoor radon concentrations were measured in 23 locations with the two-filter method. The locations were determined by a circle which the flare as the point center. The outdoor radon concentrations were measured in 74 houses (more than distance of 600 m from the flare) with the alpha track detector (CR-39) placed in the living rooms for about three months. The measurements of the radon concentrations were carried out in Cepu, Cirebon, and Prabumulih oil mine sites. The results showed that the outdoor radon concentrations a range of 108 Bq/m{sup 3} to 256 Bq/m{sup 3} in Cepu, 248 Bq/m{sup 3} to 3525 Bq/m{sup 3} in Cirebon, and 51 Bq/m{sup 3} to 114 Bq/m{sup 3} in Prabumulih. The results showed that the indoor radon concentrations a range of 11 Bq/m{sup 3} to 38 Bq/m{sup 3} in Cepu, 28 Bq/m{sup 3} to 184 Bq/m{sup 3} in Cirebon, and 12 Bq/m{sup 3} to 38 Bq/m{sup 3} in Prabumulih. The data of the maximum radon concentration in outdoor air was higher than an actual level which recommended by International Atomic Energy Agency (IAEA) for workplaces. The maximum radon concentration in indoor air was lower than an actual level which recommended by IAEA for dwellings. IAEA recommends the actual level of 1000 Bq/m{sup 3} for workplaces and 200 Bq/m{sup 3} for dwellings. These data will be used for the baseline data of the environmental radioactivity in Indonesia. (author)

  18. Determination of tritium concentrations in humans before the development of a nuclear power plant in Turkey.

    Science.gov (United States)

    Dizman, Serdar; Yilmaz, Adnan; Keser, Recep

    2015-01-01

    The most widely used method to determine the level of tritium in humans is testing urine. Tritium concentrations in urine samples of 100 persons aged 18-66 years selected randomly from a pilot region in Turkey were analysed. The average activity concentration of urine samples was 4.66 ± 1.94 Bq L(-1) and the maximum activity concentration was 27.91 Bq L(-1). The minimum detectable activity was 2.38 Bq L(-1). The annual effective dose from tritium was also evaluated on the basis of the measurement results and reference values recommended by the International Commission on Radiological Protection. The effective doses for males and females were 4.56 and 3.54 nSv, respectively. These results were lower than the permissible annual effective dose for members of the public.

  19. Variations of Ground-level Ozone Concentration in Malaysia: A Case Study in West Coast of Peninsular Malaysia

    Directory of Open Access Journals (Sweden)

    Hashim Nur Izzah Mohamad

    2017-01-01

    Full Text Available Hourly ground ozone concentration, measured from the monitoring stations in the West Coast of Peninsular Malaysia for the period of 10 years (2003-2012 were used to analyse the ozone characteristic in Nilai, Melaka and Petaling Jaya. The prediction of tropospheric ozone concentrations is very important due to the negative impacts of ozone on human health, climate and vegetation. The mean concentration of ozone at the studied areas had not exceeded the recommended value of Malaysia Ambient Air Quality Guideline (MAAQG for 8-hour average (0.06 ppm, however some of the measurements exceeded the hourly permitted concentration by MAAQG that is 0.1 ppm. Higher concentration of ozone can be observed during the daytime since ozone needs sunlight for the photochemical reactions. The diurnal cycle of ozone concentration has a mid-day peak (14:00-15:00 and lower night-time concentrations. The ozone concentration slowly rises after the sun rises (08:00, reaching a maximum during daytime and then decreases until the next morning.

  20. Determination of radon concentration in water using RAD7 with RAD H2O accessories

    International Nuclear Information System (INIS)

    Malik, M. F. I.; Rabaiee, N. A.; Jaafar, M. S.

    2015-01-01

    In the last decade, the radon issue has become one of the major problems of radiation protection. Radon exposure occurs when using water for showering, washing dishes, cooking and drinking water. RAD7 and Rad H20 accessories were used in order to measure radon concentration in water sample. In this study, four types of water were concerns which are reverse osmosis (drinking water), mineral water, tap water and well water. Reverse osmosis (drinking water) and mineral water were bought from the nearest supermarket while tap water and well water were taken from selected areas of Pulau Pinang and Kedah. Total 20 samples were taken with 5 samples for each type of water. The measured radon concentration ranged from 2.9±2.9 to 79.5±17 pCi/L, 2.9±2.9 to 67.8±16 pCi/L, 15.97±7 to 144.25±24 pCi/L and 374.89±37 to 6409.03±130 pCi/L in reverse osmosis (drinking water), mineral water, tap water and well water. Well water has the highest radon compared to others. It was due to their geological element such as granite. Results for all types of water are presented and compared with maximum contamination limit (MCL) recommended by United State Environmental Protection Agency (USEPA) which is 300pCi/L. Reverse osmosis water, mineral water and tap water were fall below MCL. However, well water was exceeded maximum level that was recommended. Thus, these findings were suggested that an action should be taken to reduce radon concentration level in well water as well as reduce a health risk towards the public

  1. Maximum entropy estimation of a Benzene contaminated plume using ecotoxicological assays

    International Nuclear Information System (INIS)

    Wahyudi, Agung; Bartzke, Mariana; Küster, Eberhard; Bogaert, Patrick

    2013-01-01

    Ecotoxicological bioassays, e.g. based on Danio rerio teratogenicity (DarT) or the acute luminescence inhibition with Vibrio fischeri, could potentially lead to significant benefits for detecting on site contaminations on qualitative or semi-quantitative bases. The aim was to use the observed effects of two ecotoxicological assays for estimating the extent of a Benzene groundwater contamination plume. We used a Maximum Entropy (MaxEnt) method to rebuild a bivariate probability table that links the observed toxicity from the bioassays with Benzene concentrations. Compared with direct mapping of the contamination plume as obtained from groundwater samples, the MaxEnt concentration map exhibits on average slightly higher concentrations though the global pattern is close to it. This suggest MaxEnt is a valuable method to build a relationship between quantitative data, e.g. contaminant concentrations, and more qualitative or indirect measurements, in a spatial mapping framework, which is especially useful when clear quantitative relation is not at hand. - Highlights: ► Ecotoxicological shows significant benefits for detecting on site contaminations. ► MaxEnt to rebuild qualitative link on concentration and ecotoxicological assays. ► MaxEnt shows similar pattern when compared with concentrations map of groundwater. ► MaxEnt is a valuable method especially when quantitative relation is not at hand. - A Maximum Entropy method to rebuild qualitative relationships between Benzene groundwater concentrations and their ecotoxicological effect.

  2. Global Harmonization of Maximum Residue Limits for Pesticides.

    Science.gov (United States)

    Ambrus, Árpád; Yang, Yong Zhen

    2016-01-13

    International trade plays an important role in national economics. The Codex Alimentarius Commission develops harmonized international food standards, guidelines, and codes of practice to protect the health of consumers and to ensure fair practices in the food trade. The Codex maximum residue limits (MRLs) elaborated by the Codex Committee on Pesticide Residues are based on the recommendations of the FAO/WHO Joint Meeting on Pesticides (JMPR). The basic principles applied currently by the JMPR for the evaluation of experimental data and related information are described together with some of the areas in which further developments are needed.

  3. Radon in indoor concentrations and indoor concentrations of metal dust particles in museums and other public buildings.

    Science.gov (United States)

    Carneiro, G L; Braz, D; de Jesus, E F; Santos, S M; Cardoso, K; Hecht, A A; Dias da Cunha, Moore K

    2013-06-01

    The aim of this study was to evaluate the public and occupational exposure to radon and metal-bearing particles in museums and public buildings located in the city of Rio de Janeiro, Brazil. For this study, four buildings were selected: two historic buildings, which currently house an art gallery and an art museum; and two modern buildings, a chapel and a club. Integrated radon concentration measurements were performed using passive radon detectors with solid state nuclear track detector-type Lexan used as nuclear track detector. Air samplers with a cyclone were used to collect the airborne particle samples that were analyzed by the particle-induced X-ray emission technique. The average unattached-radon concentrations in indoor air in the buildings were above 40 Bq/m(3), with the exception of Building D as measured in 2009. The average radon concentrations in indoor air in the four buildings in 2009 were below the recommended reference level by World Health Organization (100 Bq/m(3)); however, in 2011, the average concentrations of radon in Buildings A and C were above this level, though lower than 300 Bq/m(3). The average concentrations of unattached radon were lower than 148 Bq/m(3) (4pCi/L), the USEPA level recommended to take action to reduce the concentrations of radon in indoor air. The unattached-radon average concentrations were also lower than the value recommended by the European Union for new houses. As the unattached-radon concentrations were below the international level recommended to take action to reduce the radon concentration in air, it was concluded that during the period of sampling, there was low risk to human health due to the inhalation of unattached radon in these four buildings.

  4. Influence of aliphatic amides on the temperature of maximum density of water

    International Nuclear Information System (INIS)

    Torres, Andrés Felipe; Romero, Carmen M.

    2017-01-01

    Highlights: • The addition of amides decreases the temperature of maximum density of water suggesting a disruptive effect on water structure. • The amides in aqueous solution do not follow the Despretz equation in the concentration range considered. • The temperature shift Δθ as a function of molality is represented by a second order equation. • The Despretz constants were determined considering the dilute concentration region for each amide solution. • Solute disrupting effect of amides becomes smaller as its hydrophobic character increases. - Abstract: The influence of dissolved substances on the temperature of the maximum density of water has been studied in relation to their effect on water structure as they can change the equilibrium between structured and unstructured species of water. However, most work has been performed using salts and the studies with small organic solutes such as amides are scarce. In this work, the effect of acetamide, propionamide and butyramide on the temperature of maximum density of water was determined from density measurements using a magnetic float densimeter. Densities of aqueous solutions were measured within the temperature range from T = (275.65–278.65) K at intervals of 0.50 K in the concentration range between (0.10000 and 0.80000) mol·kg −1 . The temperature of maximum density was determined from the experimental results. The effect of the three amides is to decrease the temperature of maximum density of water and the change does not follow the Despretz equation. The results are discussed in terms of solute-water interactions and the disrupting effect of amides on water structure.

  5. Precision of commercial soil testing practice for phosphorus fertilizer recommendations in Finland

    Directory of Open Access Journals (Sweden)

    T. PELTOVUORI

    2008-12-01

    Full Text Available Implementation of the Agri-Environmental Program in 1995 has emphasized the role of advisory soil testing in phosphorus (P input planning and markedly expanded the market for commercial soil testing in Finland. A small precision experiment (5 laboratories and a simulation study on soil sampling were conducted to evaluate the current precision of the soil testing practice for P. The observed values of reproducibility (95% probability of soil P determination were 42-61% of the mean P concentration for three soils. This approximately corresponds to a maximum error of one P class in a seven-step classification system. Soil texture and organic matter content are used as secondary variables in P fertilization planning. In commercial soil testing these are both determined by finger assessment and the results have significant errors in most laboratories. Erroneous texture determinations are more likely to lead to errors in P fertilizer recommendations than soil P analysis itself. In this study the largest deviation from a correct P fertilization recommendation was +10 kg ha-1. In soil sampling simulation, stratified random sampling in areas of differing texture gave the most consistent results with geostatistical analysis of the soil test data, as compared with random, systematic, and judgment sampling strategies.;

  6. Adherence to clinic recommendations among patients with phenylketonuria in the United States.

    Science.gov (United States)

    Jurecki, E R; Cederbaum, S; Kopesky, J; Perry, K; Rohr, F; Sanchez-Valle, A; Viau, K S; Sheinin, M Y; Cohen-Pfeffer, J L

    2017-03-01

    Assess current management practices of phenylketonuria (PKU) clinics across the United States (US) based on the key treatment metrics of blood phenylalanine (Phe) concentrations and blood Phe testing frequency, as well as patient adherence to their clinic's management practice recommendations. An online survey was conducted with medical professionals from PKU clinics across the US from July to September 2015. Forty-four clinics participated in the survey and account for approximately half of PKU patients currently followed in clinics in the US (Berry et al., 2013). The majority of PKU clinics recommended target blood Phe concentrations to be between 120 and 360μM for all patients; the upper threshold was relaxed by some clinics for adult patients (from 360 to 600μM) and tightened for patients who are pregnant/planning to become pregnant (to 240μM). Patient adherence to these recommendations (percentage of patients with blood Phe below the upper recommended threshold) was age-dependent, decreasing from 88% in the 0-4years age group to 33% in adults 30+ years. Patient adherence to recommendations for blood testing frequency followed a similar trend. Higher staffing intensity (specialists per 100 PKU patients) was associated with better patient adherence to clinics' blood Phe concentrations recommendations. Clinic recommendations of target blood Phe concentrations in the US are now stricter compared to prior years, and largely reflect recent guidelines by the American College of Medical Genetics and Genomics (Vockley et al., 2014). Adherence to recommended Phe concentrations remains suboptimal, especially in older patients. However, despite remaining above the guidelines, actual blood Phe concentrations in adolescents and adults are lower than those reported in the past (Walter et al., 2002; Freehauf et al., 2013). Continued education and support for PKU patients by healthcare professionals, including adequate clinic staffing, are needed to improve adherence

  7. Determination of radon concentration in water using RAD7 with RAD H{sub 2}O accessories

    Energy Technology Data Exchange (ETDEWEB)

    Malik, M. F. I. [Science and Engineering Research Centre (SERC), Universiti Sains Malaysia, Seri Ampangan Nibong Tebal 14300 Penang (Malaysia); Rabaiee, N. A.; Jaafar, M. S. [School of Physics, Universiti Sains Malaysia, 11800 Penang (Malaysia)

    2015-04-24

    In the last decade, the radon issue has become one of the major problems of radiation protection. Radon exposure occurs when using water for showering, washing dishes, cooking and drinking water. RAD7 and Rad H20 accessories were used in order to measure radon concentration in water sample. In this study, four types of water were concerns which are reverse osmosis (drinking water), mineral water, tap water and well water. Reverse osmosis (drinking water) and mineral water were bought from the nearest supermarket while tap water and well water were taken from selected areas of Pulau Pinang and Kedah. Total 20 samples were taken with 5 samples for each type of water. The measured radon concentration ranged from 2.9±2.9 to 79.5±17 pCi/L, 2.9±2.9 to 67.8±16 pCi/L, 15.97±7 to 144.25±24 pCi/L and 374.89±37 to 6409.03±130 pCi/L in reverse osmosis (drinking water), mineral water, tap water and well water. Well water has the highest radon compared to others. It was due to their geological element such as granite. Results for all types of water are presented and compared with maximum contamination limit (MCL) recommended by United State Environmental Protection Agency (USEPA) which is 300pCi/L. Reverse osmosis water, mineral water and tap water were fall below MCL. However, well water was exceeded maximum level that was recommended. Thus, these findings were suggested that an action should be taken to reduce radon concentration level in well water as well as reduce a health risk towards the public.

  8. Effects of high salinity from desalination brine on growth, photosynthesis, water relations and osmolyte concentrations of seagrass Posidonia australis

    International Nuclear Information System (INIS)

    Cambridge, M L; Zavala-Perez, A; Cawthray, G R; Mondon, J; Kendrick, G A

    2017-01-01

    Highly saline brines from desalination plants expose seagrass communities to salt stress. We examined effects of raised salinity (46 and 54 psu) compared with seawater controls (37 psu) over 6 weeks on the seagrass, Posidonia australis, growing in tanks with the aim of separating effects of salinity from other potentially deleterious components of brine and determining appropriate bioindicators. Plants survived exposures of 2–4 weeks at 54 psu, the maximum salinity of brine released from a nearby desalination plant. Salinity significantly reduced maximum quantum yield of PSII (chlorophyll a fluorescence emissions). Leaf water potential (Ψ w ) and osmotic potential (Ψ π ) were more negative at increased salinity, while turgor pressure (Ψ p ) was unaffected. Leaf concentrations of K + and Ca 2+ decreased, whereas concentrations of sugars (mainly sucrose) and amino acids increased. We recommend leaf osmolarity, ion, sugar and amino acid concentrations as bioindicators for salinity effects, associated with brine released in desalination plant outfalls. - Highlights: • We separated salt effects of desalination brine from other deleterious components. • Sublethal salinity stress depended on both salinity increase and exposure time. • Very effective osmoregulation led to tolerance of short intervals of high salinity.

  9. Development of derived limits for radiological protection against ionizing radiation based on ICRP-60 recommendations

    International Nuclear Information System (INIS)

    Jang, S. Y.; Lee, B. S.

    1999-01-01

    Derived limits such as the Annual Limit on Intake (ALI), Derived Air Concentration (DAC) and Effluent Concentration Limit (ECL) for radiological protection against ionizing radiation based on ICRP-60 recommendations were calculated using dose limits and committed effective dose coefficients of the basic Safety Standards of IAEA (i.e. safety series 115; BSS-96). Derived limits regarding occupational exposure were derived using methodologies of ICRP-61 and dose limit stated in ICRP -60. ECL in air and water for the control of radioactive discharge into the environment were derived using methodologies of 10 CFR part 20 and dose limit stated in ICRP-60. In order to analyze the impact of implementing derived limits on nuclear facilities, the derived values in this study were compared with those prescribed in 10 CFR part 20 as well as the Maximum Permissible Concentrations (MPC) of Notice No. 98-12 of the Ministry of Science and Technology (MOST). According to the comparison results, ECLs in air and water for the control of radioactive discharge into the environment in this study are shown to have lower values (i.e. more conservative), for most part, than those in Notice No. 98-12. These differences are due to the reduction of dose limit, adoption of a weighting factor for age-dependency in dose coefficients, and application of new respiratory tract model and bio-kinetics model. Especially, for uranium elements (i.e., 235 U, 238 U, etc.), which are governing ones in the nuclear fuel industries, ECLs in water are approximately a magnitude in the order of two lower than those in Notice No. 98-12. These are attributable to the adoption of a weighting factor for age-dependency in dose coefficients, newly recommended dose coefficients for ingestion pathway, and reduction of dose limit. It was found out that the differences in ECLs in water for uranium elements originated mostly from ingestion dose coefficients recommended by BSS-96. (author). 6 refs., 2 tabs., 5 figs

  10. Maximum permissible concentrations and negligible concentrations for phthalates (dibutylphthalate and di(2-ethylhexyl)phthlate), with emphasis on endocrine disruptive properties

    NARCIS (Netherlands)

    Wezel AP van; Posthumus R; Vlaardingen P van; Crommentuijn T; Plassche EJ van de; CSR

    This report presents maximal permissible concentrations (MPCs) and negligible concentrations (NCs) are derived for di-n-butylphthalate (DBP) and di(2-ethylhexyl)phthalate (DEHP). Phthalates are often mentioned as suspected endocrine disrupters. Data with endpoints related to the endocrine or

  11. Evaluation of radon concentration in well and tap waters in Bursa (Turkey)

    International Nuclear Information System (INIS)

    Akar Tarim, U.; Gurler, O.; Akkaya, G.; Kilic, N.; Yalcin, S.; Kaynak, G.; Gundogdu, O.

    2012-01-01

    222 Rn measurements in water samples collected from 27 wells and 19 taps that were supplied from the investigated wells were conducted using the AlphaGUARD PQ 2000PRO radon gas analyser at sites across several geologic formations within the city of Bursa (Turkey). The measured radon concentrations ranged from 1.46 to 53.64 Bq l -1 for well water and from 0.91 to 12.58 Bq l -1 for tap water. Of the 27 sites sampled, only 7 had radon levels above the safe limit of 11.1 Bq l -1 recommended by the USEPA. In general, all determined concentrations were well below the 100 Bq l -1 revised reference level proposed by the European Union. These values of radon concentrations in water samples are compared with those reported from other countries. Doses resulting from the consumption of these waters were calculated. The minimum and the maximum annual mean effective doses due to 222 Rn intake through water consumption were 0.02 μSv a -1 and 1.11 μSv a -1 , respectively. (authors)

  12. Reliability of one-repetition maximum performance in people with chronic heart failure.

    Science.gov (United States)

    Ellis, Rachel; Holland, Anne E; Dodd, Karen; Shields, Nora

    2018-02-24

    Evaluate intra-rater and inter-rater reliability of the one-repetition maximum strength test in people with chronic heart failure. Intra-rater and inter-rater reliability study. A public tertiary hospital in northern metropolitan Melbourne. Twenty-four participants (nine female, mean age 71.8 ± 13.1 years) with mild to moderate heart failure of any aetiology. Lower limb strength was assessed by determining the maximum weight that could be lifted using a leg press. Intra-rater reliability was tested by one assessor on two separate occasions . Inter-rater reliability was tested by two assessors in random order. Intra-class correlation coefficients and 95% confidence intervals were calculated. Bland and Altman analyses were also conducted, including calculation of mean differences between measures ([Formula: see text]) and limits of agreement . Ten intra-rater and 21 inter-rater assessments were completed. Excellent intra-rater (intra-class correlation coefficient 2,1 0.96) and inter-rater (intra-class correlation coefficient 2,1 0.93) reliability was found. Intra-rater assessment showed less variability (mean difference 4.5 kg, limits of agreement -8.11 to 17.11 kg) than inter-rater agreement (mean difference -3.81 kg, limits of agreement -23.39 to 15.77 kg). One-repetition maximum determined using a leg press is a reliable measure in people with heart failure. Given its smaller limits of agreement, intra-rater testing is recommended. Implications for Rehabilitation Using a leg press to determine a one-repetition maximum we were able to demonstrate excellent inter-rater and intra-rater reliability using an intra-class correlation coefficient. The Bland and Altman levels of agreement were wide for inter-rater reliability and so we recommend using one assessor if measuring change in strength within an individual over time.

  13. A Distance-Adaptive Refueling Recommendation Algorithm for Self-Driving Travel

    Directory of Open Access Journals (Sweden)

    Quanli Xu

    2018-03-01

    Full Text Available Taking the maximum vehicle driving distance, the distances from gas stations, the route length, and the number of refueling gas stations as the decision conditions, recommendation rules and an early refueling service warning mechanism for gas stations along a self-driving travel route were constructed by using the algorithm presented in this research, based on the spatial clustering characteristics of gas stations and the urgency of refueling. Meanwhile, by combining ArcEngine and Matlab capabilities, a scenario simulation system of refueling for self-driving travel was developed by using c#.net in order to validate and test the accuracy and applicability of the algorithm. A total of nine testing schemes with four simulation scenarios were designed and executed using this algorithm, and all of the simulation results were consistent with expectations. The refueling recommendation algorithm proposed in this study can automatically adapt to changes in the route length of self-driving travel, the maximum driving distance of the vehicle, and the distance from gas stations, which could provide variable refueling recommendation strategies according to differing gas station layouts along the route. Therefore, the results of this study could provide a scientific reference for the reasonable planning and timely supply of vehicle refueling during self-driving travel.

  14. Radionuclide concentrations in wild waterfowl using the test reactor area radioactive leaching pond

    International Nuclear Information System (INIS)

    Halford, D.K.; Millard, J.B.; Markham, O.D.

    1978-01-01

    Waterfowl use the Test Reactor Area (TRA) Radioactive Leaching Pond on the Idaho National Engineering Laboratory Site (INEL Site) as a resting area. Daily observations of waterfowl were made to determine species composition and numbers. Eight ducks and one coot were collected from the TRA pond during 1976 and 1977. Seven background samples were also collected. Each bird was dissected and tissue samples were analyzed for gamma-emitting radionuclides. Duck tissues contained 25 radionuclides. Average and maximum radionuclide concentrations were highest in gut followed by feathers, liver, and muscle, Chromium-51 had the highest concentrations of all radionuclides identified 130,000 pCi/g (4800 Bq/g) in the gut and 37,500 pCi/g (1390 Bq/g) on the feathres). Neodymium-147 had the highest concentration on feathers of any radionuclide (104,000 pCi/g, 3850 Bq/g). Cesium-137 was the predominant radionuclide in muscle with a maximum concentration of 4,070 pCi/g (150 Bq/g). The ducks had lower radionuclide concentrations in the edible tissues than in the non-edible tissues. Potential whole-body and thyroid dose commitments to man consuming contaminated ducks were calculated using muscle concentrations of Cs-134, Cs-137, and I-131. Although assumptions used for dose calculations maximized the dose commitment to man, results indicated that consumption of contaminated duck tissue is not a radiation hazard to humans. Even the highest dose commitments were below the limits recommended for individuals of the general population by the Internatioal Commission on Radiological Protection (ICRP). The highest potential dose commitment to man would result from the consumption of an American coot known to have spent 20 days on the TRA pond. The average dose commitment to man would be 20 mrem

  15. FUZZY LOGIC BASED HYBRID RECOMMENDER OF MAXIMUM YIELD CROP USING SOIL, WEATHER AND COST

    Directory of Open Access Journals (Sweden)

    U Aadithya

    2016-07-01

    Full Text Available Our system is designed to predict best suitable crops for the region of farmer. It also suggests farming strategies for the crops such as mixed cropping, spacing, irrigation, seed treatment, etc. along with fertilizer and pesticide suggestions. This is done based on the historic soil parameters of the region and by predicting cost of crops and weather. The system is based on fuzzy logic which gets input from an Artificial Neural Network (ANN based weather prediction module. An Agricultural Named Entity Recognition (NER module is developed using Conditional Random Field (CRF to extract crop conditions data. Further, cost prediction is done based on Linear Regression equation to aid in ranking the crops recommended. Using this approach we achieved an F-Score of 54% with a precision of 77% thus accounting for the correctness of crop production.

  16. Reliability of the Load-Velocity Relationship Obtained Through Linear and Polynomial Regression Models to Predict the One-Repetition Maximum Load.

    Science.gov (United States)

    Pestaña-Melero, Francisco Luis; Haff, G Gregory; Rojas, Francisco Javier; Pérez-Castilla, Alejandro; García-Ramos, Amador

    2017-12-18

    This study aimed to compare the between-session reliability of the load-velocity relationship between (1) linear vs. polynomial regression models, (2) concentric-only vs. eccentric-concentric bench press variants, as well as (3) the within-participants vs. the between-participants variability of the velocity attained at each percentage of the one-repetition maximum (%1RM). The load-velocity relationship of 30 men (age: 21.2±3.8 y; height: 1.78±0.07 m, body mass: 72.3±7.3 kg; bench press 1RM: 78.8±13.2 kg) were evaluated by means of linear and polynomial regression models in the concentric-only and eccentric-concentric bench press variants in a Smith Machine. Two sessions were performed with each bench press variant. The main findings were: (1) first-order-polynomials (CV: 4.39%-4.70%) provided the load-velocity relationship with higher reliability than second-order-polynomials (CV: 4.68%-5.04%); (2) the reliability of the load-velocity relationship did not differ between the concentric-only and eccentric-concentric bench press variants; (3) the within-participants variability of the velocity attained at each %1RM was markedly lower than the between-participants variability. Taken together, these results highlight that, regardless of the bench press variant considered, the individual determination of the load-velocity relationship by a linear regression model could be recommended to monitor and prescribe the relative load in the Smith machine bench press exercise.

  17. MAK- and BAT values list 2003. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2003. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    The importance, application and derivation of the maximum concentrations at the workplace is explained. A material's list contains the presently valid maximum concentration values supplemented by a list of materials for which no such values were determined as yet. Furthermore there is a list of working materials clearly identified as carcinogenic, and of working materials with a sensitizing effect, aerosols and some specific working materials are discussed. Finally, the importance and the application of biological tolerance values is explained, supplemented by a materials list. (orig.) [German] In der vorliegenden neuesten Ausgabe werden erneut Bedeutung, Benutzung und Ableitung der MAK-Werte (maximale Arbeitsplatzkonzentrationen) erlaeutert. Eine Stoffliste enthaelt die derzeit gueltigen MAK-Werte, ergaenzt durch eine Aufzaehlung von Stoffen, fuer die noch keine MAK-Werte aufgestellt werden koennen. Es folgt eine Auflistung der Arbeitsstoffe, die bereits eindeutig als krebserregend ausgewiesen wurden, sowie der sensibilisierenden Arbeitsstoffe, Aerosole und einige besondere Arbeitsstoffe. Abschliessend wird die Bedeutung und Benutzung der BAT-Werte erlaeutert, ergaenzt durch eine Stoffliste. (orig.)

  18. ICRP-recommendations on dose limits for workers

    International Nuclear Information System (INIS)

    Beninson, D.J.

    1976-01-01

    Dose limits proposed by the ICRP have been incorporated in most national and international standards and their respect has caused a distribution of doses with a average not exceeding 1/10 of the maximum permissible dose. This distribution corresponds to a risk which is well within the risks in 'safe industries'. There are at present some inconsistancies in the current system of recommended limits, for example having the same limit of 5 rem for the whole-body and also for some organs. Hopefully, this incosistancy will be removed in the next recommendation of the ICRP. But the whole-body limit of 5 rem in a year has been safe and there is little ground to reduce this limit on the basis of comparisons with 'safe industries'. (orig./HP) [de

  19. 2004 list of MAK (maximum work place concentration) and BAT (biological workplace tolerance) values; MAK- und BAT-Werte-Liste 2004

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    The MAK value (maximum workplace concentration) is the highest permissible concentration of a working material occurring in the ambient air of the workplace as a gas or vapour or in suspended form which according to the present state of knowledge does not, in general, impair the health of or pose an unreasonable molestation (for example through repulsive odour) to employees even in the case of repeated, long-term exposure, that is as a rule 8 hours daily, assuming an average working week of no more than 40 hours. As a rule, MAK values are quoted as average values over a time period of up to one working day or shift. They are primarily defined in consideration of effect characteristics of the substances in question, but also - as far as possible - of the practical conditions attending the work processes or the exposure patterns which they entail. This is done on the basis of scientifically founded criteria of health protection, not on whether providing such protection is technically or economically feasible. In addition, substances are assessed in terms of carcinogenicity, sensitising effects, any contribution to systemic toxicity following cutaneous resorption, hazards for pregnancy and germ cell mutagenicity and are classified or marked accordingly. The Commission's procedures in assessing substances with respect to these criteria are described in corresponding sections of the MAK and BAT list of values, in the ''Toxicological and occupational medical explanations of MAK values'' and in scientific journals.

  20. Erich Regener and the ionisation maximum of the atmosphere

    Science.gov (United States)

    Carlson, P.; Watson, A. A.

    2014-12-01

    In the 1930s the German physicist Erich Regener (1881-1955) did important work on the measurement of the rate of production of ionisation deep under water and in the atmosphere. Along with one of his students, Georg Pfotzer, he discovered the altitude at which the production of ionisation in the atmosphere reaches a maximum, often, but misleadingly, called the Pfotzer maximum. Regener was one of the first to estimate the energy density of cosmic rays, an estimate that was used by Baade and Zwicky to bolster their postulate that supernovae might be their source. Yet Regener's name is less recognised by present-day cosmic ray physicists than it should be, largely because in 1937 he was forced to take early retirement by the National Socialists as his wife had Jewish ancestors. In this paper we briefly review his work on cosmic rays and recommend an alternative naming of the ionisation maximum. The influence that Regener had on the field through his son, his son-in-law, his grandsons and his students, and through his links with Rutherford's group in Cambridge, is discussed in an appendix. Regener was nominated for the Nobel Prize in Physics by Schrödinger in 1938. He died in 1955 at the age of 73.

  1. Numerical simulation of the double pits stress concentration in a curved casing inner surface

    Directory of Open Access Journals (Sweden)

    Wei Yan

    2016-12-01

    Full Text Available Sour or sweet oil fields development is common in recent years. Casing and tubing are usually subjected to pitting corrosion because of exposure to the strong corrosion species, such as CO2, H2S, and saline water. When the corrosion pits formed in the casing inner surface, localized stress concentration will occur and the casing strength will be degraded. Thus, it is essential to evaluate the degree of stress concentration factor accurately. This article performed a numerical simulation on double pits stress concentration factor in a curved inner surface using the finite element software ABAQUS. The results show that the stress concentration factor of double pits mainly depends on the ratio of two pits distance to the pit radius (L/R. It should not be only assessed by the absolute distance between the two pits. When the two pits are close and tangent, the maximum stress concentration factor will appear on the inner tangential edges. Stress concentration increased by double pits in a curved casing inner surface is more serious than that in a flat surface. A correction factor of 1.9 was recommended in the curved inner surface double pits stress concentration factor predict model.

  2. Cost Recommendation under Uncertainty in IQWiG's Efficiency Frontier Framework.

    Science.gov (United States)

    Corro Ramos, Isaac; Lhachimi, Stefan K; Gerber-Grote, Andreas; Al, Maiwenn J

    2017-02-01

    The National Institute for Quality and Efficiency in Health Care (IQWiG) employs an efficiency frontier (EF) framework to facilitate setting maximum reimbursable prices for new interventions. Probabilistic sensitivity analysis (PSA) is used when yes/no reimbursement decisions are sought based on a fixed threshold. In the IQWiG framework, an additional layer of complexity arises as the EF itself may vary its shape in each PSA iteration, and thus the willingness-to-pay, indicated by the EF segments, may vary. To explore the practical problems arising when, within the EF approach, maximum reimbursable prices for new interventions are sought through PSA. When the EF is varied in a PSA, cost recommendations for new interventions may be determined by the mean or the median of the distances between each intervention's point estimate and each EF. Implications of using these metrics were explored in a simulation study based on the model used by IQWiG to assess the cost-effectiveness of 4 antidepressants. Depending on the metric used, cost recommendations can be contradictory. Recommendations based on the mean can also be inconsistent. Results (median) suggested that costs of duloxetine, venlafaxine, mirtazapine, and bupropion should be decreased by €131, €29, €12, and €99, respectively. These recommendations were implemented and the analysis repeated. New results suggested keeping the costs as they were. The percentage of acceptable PSA outcomes increased 41% on average, and the uncertainty associated to the net health benefit was significantly reduced. The median of the distances between every intervention outcome and every EF is a good proxy for the cost recommendation that would be given should the EF be fixed. Adjusting costs according to the median increased the probability of acceptance and reduced the uncertainty around the net health benefit distribution, resulting in a reduced uncertainty for decision makers.

  3. A Review of Heavy Metal Concentration and Potential Health Implications of Beverages Consumed in Nigeria

    Directory of Open Access Journals (Sweden)

    Sylvester Chibueze Izah

    2016-12-01

    Full Text Available Beverages are consumed in Nigeria irrespective of age, sex, and socioeconomic status. Beverages may be alcoholic (wine, spirits, and beers or non-alcoholic (soft drink, energy drinks, candies, chocolates, milks. Notwithstanding, most beverages are packed in cans, bottles, and plastics. This paper reviews the concentration of heavy metals from some commercially-packaged beverages consumed in Nigeria. The study found that heavy metal concentrations, including iron, mercury, tin, antimony, cadmium, zinc, copper, chromium, lead, and manganese, seldom exceed the maximum contaminant level recommended by the Standard Organization of Nigeria (SON and the World Health Organization (WHO as applicable to drinking water resources. The occurrence of heavy metals in the beverages could have resulted from the feedstocks and water used in their production. Consumption of beverages high in heavy metal could be toxic and cause adverse effect to human health, depending on the rate of exposure and accumulation dosage. This study concludes by suggesting that heavy metal concentration in the feedstocks and water should be monitored by producers, and its concentration in beverages should also be monitored by appropriate regulatory agencies.

  4. Verification of average daily maximum permissible concentration of styrene in the atmospheric air of settlements under the results of epidemiological studies of the children’s population

    Directory of Open Access Journals (Sweden)

    М.А. Zemlyanova

    2015-03-01

    Full Text Available We presented the materials on the verification of the average daily maximum permissible concentration of styrene in the atmospheric air of settlements performed under the results of own in-depth epidemiological studies of children’s population according to the principles of the international risk assessment practice. It was established that children in the age of 4–7 years when exposed to styrene at the level above 1.2 of threshold level value for continuous exposure develop the negative exposure effects in the form of disorders of hormonal regulation, pigmentary exchange, antioxidative activity, cytolysis, immune reactivity and cytogenetic disbalance which contribute to the increased morbidity of diseases of the central nervous system, endocrine system, respiratory organs, digestion and skin. Based on the proved cause-and-effect relationships between the biomarkers of negative effects and styrene concentration in blood it was demonstrated that the benchmark styrene concentration in blood is 0.002 mg/dm3. The justified value complies with and confirms the average daily styrene concentration in the air of settlements at the level of 0.002 mg/m3 accepted in Russia which provides the safety for the health of population (1 threshold level value for continuous exposure.

  5. Towards a frequency-dependent discrete maximum principle for the implicit Monte Carlo equations

    Energy Technology Data Exchange (ETDEWEB)

    Wollaber, Allan B [Los Alamos National Laboratory; Larsen, Edward W [Los Alamos National Laboratory; Densmore, Jeffery D [Los Alamos National Laboratory

    2010-12-15

    It has long been known that temperature solutions of the Implicit Monte Carlo (IMC) equations can exceed the external boundary temperatures, a so-called violation of the 'maximum principle.' Previous attempts at prescribing a maximum value of the time-step size {Delta}{sub t} that is sufficient to eliminate these violations have recommended a {Delta}{sub t} that is typically too small to be used in practice and that appeared to be much too conservative when compared to numerical solutions of the IMC equations for practical problems. In this paper, we derive a new estimator for the maximum time-step size that includes the spatial-grid size {Delta}{sub x}. This explicitly demonstrates that the effect of coarsening {Delta}{sub x} is to reduce the limitation on {Delta}{sub t}, which helps explain the overly conservative nature of the earlier, grid-independent results. We demonstrate that our new time-step restriction is a much more accurate means of predicting violations of the maximum principle. We discuss how the implications of the new, grid-dependent timestep restriction can impact IMC solution algorithms.

  6. Towards a frequency-dependent discrete maximum principle for the implicit Monte Carlo equations

    International Nuclear Information System (INIS)

    Wollaber, Allan B.; Larsen, Edward W.; Densmore, Jeffery D.

    2011-01-01

    It has long been known that temperature solutions of the Implicit Monte Carlo (IMC) equations can exceed the external boundary temperatures, a so-called violation of the 'maximum principle'. Previous attempts at prescribing a maximum value of the time-step size Δ t that is sufficient to eliminate these violations have recommended a Δ t that is typically too small to be used in practice and that appeared to be much too conservative when compared to numerical solutions of the IMC equations for practical problems. In this paper, we derive a new estimator for the maximum time-step size that includes the spatial-grid size Δ x . This explicitly demonstrates that the effect of coarsening Δ x is to reduce the limitation on Δ t , which helps explain the overly conservative nature of the earlier, grid-independent results. We demonstrate that our new time-step restriction is a much more accurate means of predicting violations of the maximum principle. We discuss how the implications of the new, grid-dependent time-step restriction can impact IMC solution algorithms. (author)

  7. Functional Maximum Autocorrelation Factors

    DEFF Research Database (Denmark)

    Larsen, Rasmus; Nielsen, Allan Aasbjerg

    2005-01-01

    MAF outperforms the functional PCA in concentrating the interesting' spectra/shape variation in one end of the eigenvalue spectrum and allows for easier interpretation of effects. Conclusions. Functional MAF analysis is a useful methods for extracting low dimensional models of temporally or spatially......Purpose. We aim at data where samples of an underlying function are observed in a spatial or temporal layout. Examples of underlying functions are reflectance spectra and biological shapes. We apply functional models based on smoothing splines and generalize the functional PCA in......\\verb+~+\\$\\backslash\\$cite{ramsay97} to functional maximum autocorrelation factors (MAF)\\verb+~+\\$\\backslash\\$cite{switzer85,larsen2001d}. We apply the method to biological shapes as well as reflectance spectra. {\\$\\backslash\\$bf Methods}. MAF seeks linear combination of the original variables that maximize autocorrelation between...

  8. Board advice following publication of the 1990 Recommendations of ICRP

    International Nuclear Information System (INIS)

    1991-11-01

    The International Commission on Radiological Protection (ICRP) has published new Recommendations and the Board has a statutory duty to advise Government and those with responsibilities for radiation protection on the acceptability to and the applicability in the UK of those Recommendations. The Board wishes to consult widely before finalising the advice which is proposed in this document. In general, the Board endorses the conceptual framework for radiological protection recommended by ICRP. In particular, the distinction between practices and intervention is useful and is consistent with the way in which the Board has presented its recent advice. A major new concept is that of a constraint. The Board believes that the introduction of constraints provides a powerful method for improving protection against ionising radiation. The advice in this consultative document is for maximum generic values of dose constraints for both workers and the public. Finally the Board proposes to endorse the use of the radiological quantities recommended by ICRP. (author)

  9. [The maximum heart rate in the exercise test: the 220-age formula or Sheffield's table?].

    Science.gov (United States)

    Mesquita, A; Trabulo, M; Mendes, M; Viana, J F; Seabra-Gomes, R

    1996-02-01

    To determine in the maximum cardiac rate in exercise test of apparently healthy individuals may be more properly estimated through 220-age formula (Astrand) or the Sheffield table. Retrospective analysis of clinical history and exercises test of apparently healthy individuals submitted to cardiac check-up. Sequential sampling of 170 healthy individuals submitted to cardiac check-up between April 1988 and September 1992. Comparison of maximum cardiac rate of individuals studied by the protocols of Bruce and modified Bruce, in interrupted exercise test by fatigue, and with the estimated values by the formulae: 220-age versus Sheffield table. The maximum cardiac heart rate is similar with both protocols. This parameter in normal individuals is better predicted by the 220-age formula. The theoretic maximum cardiac heart rate determined by 220-age formula should be recommended for a healthy, and for this reason the Sheffield table has been excluded from our clinical practice.

  10. Approximate maximum parsimony and ancestral maximum likelihood.

    Science.gov (United States)

    Alon, Noga; Chor, Benny; Pardi, Fabio; Rapoport, Anat

    2010-01-01

    We explore the maximum parsimony (MP) and ancestral maximum likelihood (AML) criteria in phylogenetic tree reconstruction. Both problems are NP-hard, so we seek approximate solutions. We formulate the two problems as Steiner tree problems under appropriate distances. The gist of our approach is the succinct characterization of Steiner trees for a small number of leaves for the two distances. This enables the use of known Steiner tree approximation algorithms. The approach leads to a 16/9 approximation ratio for AML and asymptotically to a 1.55 approximation ratio for MP.

  11. STUDY ON MAXIMUM SPECIFIC SLUDGE ACIVITY OF DIFFERENT ANAEROBIC GRANULAR SLUDGE BY BATCH TESTS

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The maximum specific sludge activity of granular sludge from large-scale UASB, IC and Biobed anaerobic reactors were investigated by batch tests. The limitation factors related to maximum specific sludge activity (diffusion, substrate sort, substrate concentration and granular size) were studied. The general principle and procedure for the precise measurement of maximum specific sludge activity were suggested. The potential capacity of loading rate of the IC and Biobed anaerobic reactors were analyzed and compared by use of the batch tests results.

  12. International recommendations

    International Nuclear Information System (INIS)

    Lindell, Bo

    1986-01-01

    Publication 40, the ICRP has recommended ranges of action levels for some remedial actions, including the withdrawal of contaminated food-stuffs from the market. Similar recommendations have been issued by IAEA and WHO. From recommended values of action levels for radiation dose, derived action levels for intakes (e.g. annual intakes) of various radionuclides may be calculated, provided that the relative proportions of all significant radionuclides are known. Values of such derived action levels have been published by the IAEA in its Safety Series No. 81. On these bases, national authorities, have intervened to give 'limits' or 'reference values' for activity concentrations (in Bq/kg) for some or all food-stuffs. It should be realized, however, that the actual activity intake, and hence the radiation dose and risk, depend not only on the activity concentration but also on the quantities of particular food-stuffs actually consumed. (author)

  13. Concentration of trace metals in boreholes in the Ankobra Basin, Ghana

    International Nuclear Information System (INIS)

    Kortasi, B. K.

    2006-01-01

    Analysis of trace metals in ground water from the Ankobra basin revealed high levels of iron, manganese and aluminium. Approximately 40% of boreholes had total iron concentration exceeding 1000 μ 1 -1 (maximum WHO permissible limit). Aluminium concentration varied from 0.1 μ to 2510 μ 1 -1 with a median value of 10.0 μ 1 -1 . Approximately 20% of the boreholes had aluminium concentration exceeding the WHO maximum acceptable limit (200 μ 1 -1 ) for drinking water. Manganese concentration was in the range 6-2510 μ 1 -1 with a median of 356 μ 1 -1 . Roughly 25% of the boreholes had manganese concentrations higher that 500 μ 1 -1 , which is the WHO maximum acceptable limit for drinking water. The concentrations of mercury was higher than 1.0 μ 1 -1 (WHO maximum acceptable limit) in 60% of the boreholes during the rainy season but below detection limit in the dry season, suggesting anthropogenic origin for mercury in the groundwater. Other trace metals that occurred, but in insignificant concentration in the boreholes, include lead, arsenic, nickel and selenium. Most of the boreholes with high trace metal concentrations were located in and around the Bawdie-Bogoso-Prestea area. (au)

  14. Management of pancreatic exocrine insufficiency: Australasian Pancreatic Club recommendations.

    Science.gov (United States)

    Toouli, James; Biankin, Andrew V; Oliver, Mark R; Pearce, Callum B; Wilson, Jeremy S; Wray, Nicholas H

    2010-10-18

    Pancreatic exocrine insufficiency (PEI) occurs when the amounts of enzymes secreted into the duodenum in response to a meal are insufficient to maintain normal digestive processes. The main clinical consequence of PEI is fat maldigestion and malabsorption, resulting in steatorrhoea. Pancreatic exocrine function is commonly assessed by conducting a 3-day faecal fat test and by measuring levels of faecal elastase-1 and serum trypsinogen. Pancreatic enzyme replacement therapy is the mainstay of treatment for PEI. In adults, the initial recommended dose of pancreatic enzymes is 25,000 units of lipase per meal, titrating up to a maximum of 80,000 units of lipase per meal. In infants and children, the initial recommended dose of pancreatic enzymes is 500 units of lipase per gram of dietary fat; the maximum daily dose should not exceed 10,000 units of lipase per kilogram of bodyweight. Oral pancreatic enzymes should be taken with meals to ensure adequate mixing with the chyme. Adjunct therapy with acid-suppressing agents may be useful in patients who continue to experience symptoms of PEI despite high-dose enzyme therapy. A dietitian experienced in treating PEI should be involved in patient management. Dietary fat restriction is not recommended for patients with PEI. Patients with PEI should be encouraged to consume small, frequent meals and to abstain from alcohol. Medium-chain triglycerides do not provide any clear nutritional advantage over long-chain triglycerides, but can be trialled in patients who fail to gain or to maintain adequate bodyweight in order to increase energy intake.

  15. Reconstruction of the electron momentum density distribution by the maximum entropy method

    International Nuclear Information System (INIS)

    Dobrzynski, L.

    1996-01-01

    The application of the Maximum Entropy Algorithm to the analysis of the Compton profiles is discussed. It is shown that the reconstruction of electron momentum density may be reliably carried out. However, there are a number of technical problems which have to be overcome in order to produce trustworthy results. In particular one needs the experimental Compton profiles measured for many directions, and to have efficient computational resources. The use of various cross-checks is recommended. (orig.)

  16. Optimal Control of Polymer Flooding Based on Maximum Principle

    Directory of Open Access Journals (Sweden)

    Yang Lei

    2012-01-01

    Full Text Available Polymer flooding is one of the most important technologies for enhanced oil recovery (EOR. In this paper, an optimal control model of distributed parameter systems (DPSs for polymer injection strategies is established, which involves the performance index as maximum of the profit, the governing equations as the fluid flow equations of polymer flooding, and the inequality constraint as the polymer concentration limitation. To cope with the optimal control problem (OCP of this DPS, the necessary conditions for optimality are obtained through application of the calculus of variations and Pontryagin’s weak maximum principle. A gradient method is proposed for the computation of optimal injection strategies. The numerical results of an example illustrate the effectiveness of the proposed method.

  17. Extracorporeal treatment for thallium poisoning: recommendations from the EXTRIP Workgroup.

    Science.gov (United States)

    Ghannoum, Marc; Nolin, Thomas D; Goldfarb, David S; Roberts, Darren M; Mactier, Robert; Mowry, James B; Dargan, Paul I; Maclaren, Robert; Hoegberg, Lotte C; Laliberté, Martin; Calello, Diane; Kielstein, Jan T; Anseeuw, Kurt; Winchester, James F; Burdmann, Emmanuel A; Bunchman, Timothy E; Li, Yi; Juurlink, David N; Lavergne, Valery; Megarbane, Bruno; Gosselin, Sophie; Liu, Kathleen D; Hoffman, Robert S

    2012-10-01

    The EXtracorporeal TReatments In Poisoning (EXTRIP) workgroup was formed to provide recommendations on the use of extracorporeal treatment (ECTR) in poisoning. To test and validate its methods, the workgroup reviewed data for thallium (Tl). After an extensive search, the co-chairs reviewed the articles, extracted the data, summarized findings, and proposed structured voting statements following a predetermined format. A two-round modified Delphi method was chosen to reach a consensus on voting statements and RAND/UCLA Appropriateness Method to quantify disagreement. Blinded votes were compiled, returned, and discussed during a conference call. A second vote determined the final recommendations. Forty-five articles met inclusion criteria. Only case reports and case series were identified, yielding a very low quality of evidence for all recommendations. Data on 74 patients, including 11 who died, were abstracted. The workgroup concluded that Tl is slightly dialyzable and made the following recommendations: ECTR is recommended in severe Tl poisoning (1D). ECTR is indicated if Tl exposure is highly suspected on the basis of history or clinical features (2D) or if the serum Tl concentration is >1.0 mg/L (2D). ECTR should be initiated as soon as possible, ideally within 24-48 hours of Tl exposure (1D), and be continued until the serum Tl concentration is poisoning.

  18. Analysis to determine the maximum dimensions of flexible apertures in sensored security netting products.

    Energy Technology Data Exchange (ETDEWEB)

    Murton, Mark; Bouchier, Francis A.; vanDongen, Dale T.; Mack, Thomas Kimball; Cutler, Robert P; Ross, Michael P.

    2013-08-01

    Although technological advances provide new capabilities to increase the robustness of security systems, they also potentially introduce new vulnerabilities. New capability sometimes requires new performance requirements. This paper outlines an approach to establishing a key performance requirement for an emerging intrusion detection sensor: the sensored net. Throughout the security industry, the commonly adopted standard for maximum opening size through barriers is a requirement based on square inchestypically 96 square inches. Unlike standard rigid opening, the dimensions of a flexible aperture are not fixed, but variable and conformable. It is demonstrably simple for a human intruder to move through a 96-square-inch opening that is conformable to the human body. The longstanding 96-square-inch requirement itself, though firmly embedded in policy and best practice, lacks a documented empirical basis. This analysis concluded that the traditional 96-square-inch standard for openings is insufficient for flexible openings that are conformable to the human body. Instead, a circumference standard is recommended for these newer types of sensored barriers. The recommended maximum circumference for a flexible opening should be no more than 26 inches, as measured on the inside of the netting material.

  19. Entropy concentration and the empirical coding game

    NARCIS (Netherlands)

    Grünwald, P.D.

    2008-01-01

    We give a characterization of maximum entropy/minimum relative entropy inference by providing two 'strong entropy concentration' theorems. These theorems unify and generalize Jaynes''concentration phenomenon' and Van Campenhout and Cover's 'conditional limit theorem'. The theorems characterize

  20. Maximum permissible dose

    International Nuclear Information System (INIS)

    Anon.

    1979-01-01

    This chapter presents a historic overview of the establishment of radiation guidelines by various national and international agencies. The use of maximum permissible dose and maximum permissible body burden limits to derive working standards is discussed

  1. Suboptimal Antituberculosis Drug Concentrations and Outcomes in Small and HIV-Coinfected Children in India: Recommendations for Dose Modifications.

    Science.gov (United States)

    Guiastrennec, Benjamin; Ramachandran, Geetha; Karlsson, Mats O; Kumar, A K Hemanth; Bhavani, Perumal Kannabiran; Gangadevi, N Poorana; Swaminathan, Soumya; Gupta, Amita; Dooley, Kelly E; Savic, Radojka M

    2017-12-16

    This work aimed to evaluate the once-daily antituberculosis treatment as recommended by the new Indian pediatric guidelines. Isoniazid, rifampin, and pyrazinamide concentration-time profiles and treatment outcome were obtained from 161 Indian children with drug-sensitive tuberculosis undergoing thrice-weekly dosing as per previous Indian pediatric guidelines. The exposure-response relationships were established using a population pharmacokinetic-pharmacodynamic approach. Rifampin exposure was identified as the unique predictor of treatment outcome. Consequently, children with low body weight (4-7 kg) and/or HIV infection, who displayed the lowest rifampin exposure, were associated with the highest probability of unfavorable treatment (therapy failure, death) outcome (P unfavorable ). Model-based simulation of optimized (P unfavorable ≤ 5%) rifampin once-daily doses were suggested per treatment weight band and HIV coinfection status (33% and 190% dose increase, respectively, from the new Indian guidelines). The established dose-exposure-response relationship could be pivotal in the development of future pediatric tuberculosis treatment guidelines. © 2017, The Authors Clinical Pharmacology & Therapeutics published by Wiley Periodicals, Inc. on behalf of American Society for Clinical Pharmacology and Therapeutics.

  2. Radionuclide concentrations and dose assessment of cistern water and groundwater at the Marshall Islands

    International Nuclear Information System (INIS)

    Noshkin, V.E.; Eagle, R.J.; Wong, K.M.; Jokela, T.A.; Robison, W.L.

    1981-01-01

    A radiological survey was conducted from September through November of 1978 to determine the concentrations of radionuclides in the terrestrial and marine environments of 11 atolls and 2 islands in the Northern Marshall Islands. More than 70 cistern and groundwater samples were collected at the atolls; the volume of each sample was between 55 and 100 l. The concentration of 90 Sr in cistern water at most atolls is that expected from world-wide fallout in wet deposition. Except for Bikini and Rongelap, 137 Cs concentrations in cistern water are in agreement with the average predicted concentrations from wet deposition. The 239+240 Pu concentrations are everywhere less than the predicted fallout concentrations except at Rongelap, Ailinginae, and Bikini where the measured and predicted concentrations are in general agreement. During the period sampled, most groundwater concentrations of 90 Sr and 137 Cs were everywhere higher than the concentrations in cistern water. Concentrations of the transurancies in filtered groundwater solution were everywhere comparable to or less than the concentrations in cistern water. It is concluded that the concentrations of radionuclides detected during any single period may not necessarily reflect the long-term average concentrations or the concentrations that might be observed if a lined well were extended above the surface. In any case, at all atolls the 90 Sr and 137 Cs concentrations in groundwater are below the concentration guidelines for drinking water recommended by the Environmental Protection Agency. The maximum annual dose rates and the 30- and 50-y integral doses are calculated for the intake of both cistern water and groundwater for each of the atolls

  3. Color corrected Fresnel lens for solar concentration

    International Nuclear Information System (INIS)

    Kritchman, E.M.

    1979-01-01

    A new linear convex Fresnel lens with its groove side down is described. The design philosophy is similar to the highly concentrating two focal Fresnel lens but including a correction for chromatic aberration. A solar concentration ratio as high as 80 is achieved. For wide acceptance angles the concentration nears the theoretical maximum. (author)

  4. Time to reach tacrolimus maximum blood concentration,mean residence time, and acute renal allograft rejection: an open-label, prospective, pharmacokinetic study in adult recipients.

    Science.gov (United States)

    Kuypers, Dirk R J; Vanrenterghem, Yves

    2004-11-01

    The aims of this study were to determine whether disposition-related pharmacokinetic parameters such as T(max) and mean residence time (MRT) could be used as predictors of clinical efficacy of tacrolimus in renal transplant recipients, and to what extent these parameters would be influenced by clinical variables. We previously demonstrated, in a prospective pharmacokinetic study in de novo renal allograft recipients, that patients who experienced early acute rejection did not differ from patients free from rejection in terms of tacrolimus pharmacokinetic exposure parameters (dose interval AUC, preadministration trough blood concentration, C(max), dose). However, recipients with acute rejection reached mean (SD) tacrolimus T(max) significantly faster than those who were free from rejection (0.96 [0.56] hour vs 1.77 [1.06] hours; P clearance nor T(1/2) could explain this unusual finding, we used data from the previous study to calculate MRT from the concentration-time curves. As part of the previous study, 100 patients (59 male, 41 female; mean [SD] age, 51.4 [13.8] years;age range, 20-75 years) were enrolled in the study The calculated MRT was significantly shorter in recipients with acute allograft rejection (11.32 [031] hours vs 11.52 [028] hours; P = 0.02), just like T(max) was an independent risk factor for acute rejection in a multivariate logistic regression model (odds ratio, 0.092 [95% CI, 0.014-0.629]; P = 0.01). Analyzing the impact of demographic, transplantation-related, and biochemical variables on MRT, we found that increasing serum albumin and hematocrit concentrations were associated with a prolonged MRT (P calculated MRT were associated with a higher incidence of early acute graft rejection. These findings suggest that a shorter transit time of tacrolimus in certain tissue compartments, rather than failure to obtain a maximum absolute tacrolimus blood concentration, might lead to inadequate immunosuppression early after transplantation.

  5. Performance investigation of a concentrating photovoltaic/thermal system with transmissive Fresnel solar concentrator

    International Nuclear Information System (INIS)

    Feng, Chaoqing; Zheng, Hongfei; Wang, Rui; Ma, Xinglong

    2016-01-01

    Highlights: • A common design method of a cycloidal transmissive Fresnel solar concentrator was presented. • The gallium arsenide high concentrated solar was used as the receiver. • High efficiency of electric generating could be achieved at noon. • Fresnel solar concentrator was studied and compared in hazy weather and clear weather. - Abstract: A design method of a cycloidal transmissive Fresnel solar concentrator which can provide a certain width focal line was presented in this study. Based on the optical principle of refraction, the dimensions of each wedge-shaped element of Fresnel lens are calculated. An optical simulation has been done to obtain the optical efficiency of the concentrator for different tracking error and axial incidence angle. It has been found that about 80% of the incident sunlight can still be gathered by the absorber when the tracking error is within 0.7°. When the axial angle of incidence is within 10°, it almost has no influence to the receiving rate. The concentrating photovoltaic/thermal system with transmissive Fresnel solar concentrator has been designed in this paper. Take the gallium arsenide high concentrated battery as the receiver, experimental research about cylindrical Fresnel concentrating photovoltaic/thermal system is undertaken in the real sky. Main parameters are tested such as the temperature distribution on receiver, electric energy and thermal energy outputs of concentrating photovoltaic/thermal system, the efficiency of multipurpose utilization of electric and heat, and so on. The test results in clear weather show that maximum electric generating efficiency is about 18% at noon, the maximum heat receiving rate of cooling water is about 45%. At noon time (11:00–13:00), the total efficiency of thermal and electricity can reach more than 55%. Performance of this concentrating photovoltaic/thermal system with transmissive Fresnel solar concentrator is studied and compared in two types typical weather, hazy

  6. Effect of tetrastarch (hydroxyethyl starch 130/0.4) on plasma creatinine concentration in cats: a retrospective analysis (2010-2015).

    Science.gov (United States)

    Yozova, Ivayla D; Howard, Judith; Adamik, Katja N

    2017-10-01

    Objectives The objective was to determine survival and changes in creatinine concentrations after administration of 6% tetrastarch (hydroxyethyl starch [HES] 130/0.4) vs crystalloids in critically ill cats. Methods The medical records were reviewed for cats admitted to the intensive care unit with at least two plasma creatinine measurements and initial concentrations not exceeding the upper reference interval. Cats were excluded if they had received HES prior to admission or if they had received fluid therapy for creatinine concentrations were evaluated as the percentage change from initial values to the maximum subsequent measurements. Cats receiving only crystalloids were assigned to the crystalloid group; cats receiving only HES or HES and crystalloids were assigned to the HES group. Results Ninety-three cats were included in the study (62 in the crystalloid group, 31 in the HES group). The total median cumulative HES dose was 94 ml/kg (range 26-422 ml/kg) and 24 ml/kg/day (range 16-42 ml/kg/day). No difference was detected between the groups for age, sex, body weight or mortality. The HES group had a significantly longer length of hospitalisation ( P = 0.012), lower albumin concentrations ( P creatinine concentrations between the groups. Moreover, there was no significant difference in maximum change in creatinine concentrations in the subgroups of cats with systemic inflammatory response syndrome or sepsis. Conclusions and relevance In this population of cats, the administration of HES did not result in a significantly greater increase in creatinine from values measured on admission or higher mortality compared with administration of crystalloids. Further prospective studies are needed to assess both safety and efficacy of HES in cats before recommendations can be made.

  7. BfR recommends the establishment of a European maximum level for uranium in drinking and mineral water

    OpenAIRE

    German Federal Institute for Risk Assessment

    2007-01-01

    Uranium is a widespread, radioactive heavy metal on earth. It is to be found in varying concentrations and states in various rocks and minerals as well as in water, soil and air. Uranium may also reach the environment anthropogenically for instance in mineral phosphate fertilisers. Because of its widespread presence traces of uranium can also be detected in foods like drinking and mineral water. Uranium is not essential for humans. The ongoing intake of higher uranium concentration...

  8. A Hybrid Recommender System Based on User-Recommender Interaction

    OpenAIRE

    Zhang, Heng-Ru; Min, Fan; He, Xu; Xu, Yuan-Yuan

    2015-01-01

    Recommender systems are used to make recommendations about products, information, or services for users. Most existing recommender systems implicitly assume one particular type of user behavior. However, they seldom consider user-recommender interactive scenarios in real-world environments. In this paper, we propose a hybrid recommender system based on user-recommender interaction and evaluate its performance with recall and diversity metrics. First, we define the user-recommender interaction...

  9. Board advice following publication of the 1990 Recommendations of ICRP

    CERN Document Server

    United Kingdom. At. Energy Res. Establ. Nat. Radiolog. Protect. Board. Harwell

    1991-01-01

    The International Commission on Radiological Protection (ICRP) has published new Recommendations and the board has a statutory duty to advise Government and those with responsibilities for radiation protection on the acceptability to and the applicability in the UK of those Recommendations. The Board wishes to consult widely before finalising the advice which is proposed in this document. In general, the Board endorses the conceptual framework for radiological protection recommended by ICRP. In particular, the distinction between practices and intervention is useful and is consistent with the way in which the Board has presented its recent advice. A major new concept is that of a constraint. The Board believes that the introduction of constraints provides a powerful method for improving protection against ionising radiation. The advice in this consultative document is for maximum generic values of dose constraints for both workers and the public. Finally the Board proposes to endorse the use of the radiologic...

  10. A Kinetic Model to Explain the Maximum in alpha-Amylase Activity Measurements in the Presence of Small Carbohydrates

    NARCIS (Netherlands)

    Baks, T.; Janssen, A.E.M.; Boom, R.M.

    2006-01-01

    The effect of the presence of several small carbohydrates on the measurement of the -amylase activity was determined over a broad concentration range. At low carbohydrate concentrations, a distinct maximum in the -amylase activity versus concentration curves was observed in several cases. At higher

  11. Comparison of current recommended regimens of atropinization in organophosphate poisoning.

    Science.gov (United States)

    Connors, Nicholas J; Harnett, Zachary H; Hoffman, Robert S

    2014-06-01

    Atropine is the mainstay of therapy in organophosphate (OP) toxicity, though research and consensus on dosing is lacking. In 2004, as reported by Eddleston et al. (J Toxicol Clin Toxicol 42(6):865-75, 2004), they noted variation in recommended regimens. We assessed revisions of original references, additional citations, and electronic sources to determine the current variability in atropine dosing recommendations. Updated editions of references from Eddleston et al.'s work, texts of Internal and Emergency Medicine, and electronic resources were reviewed for atropine dosing recommendations. For comparison, recommendations were assessed using the same mean dose (23.4 mg) and the highest dose (75 mg) of atropine as used in the original paper. Recommendations were also compared with the dosing regimen from the World Health Organization (WHO). Thirteen of the original recommendations were updated and 15 additional references were added giving a convenience sample of 28. Sufficient information to calculate time to targeted dose was provided by 24 of these samples. Compared to 2004, current recommendations have greatly increased the speed of atropinization with 13/24 able to reach the mean and high atropine dose within 30 min compared to 1/36 in 2004. In 2004, there were 13 regimens where the maximum time to reach 75 mg was over 18 h, whereas now, there are 2. While only one recommendation called for doubling the dose for faster escalation in 2004, 15 of the 24 current works include dose doubling. In 2004, Eddleston et al. called for an evidence-based guideline for the treatment of OP poisoning that could be disseminated worldwide. Many current recommendations can adequately treat patients within 1 h. While the WHO recommendations remain slow to treat patients with OP poisoning, other authorities are close to a consensus on rapid atropinization.

  12. Energy-Efficient Algorithm for Sensor Networks with Non-Uniform Maximum Transmission Range

    Directory of Open Access Journals (Sweden)

    Yimin Yu

    2011-06-01

    Full Text Available In wireless sensor networks (WSNs, the energy hole problem is a key factor affecting the network lifetime. In a circular multi-hop sensor network (modeled as concentric coronas, the optimal transmission ranges of all coronas can effectively improve network lifetime. In this paper, we investigate WSNs with non-uniform maximum transmission ranges, where sensor nodes deployed in different regions may differ in their maximum transmission range. Then, we propose an Energy-efficient algorithm for Non-uniform Maximum Transmission range (ENMT, which can search approximate optimal transmission ranges of all coronas in order to prolong network lifetime. Furthermore, the simulation results indicate that ENMT performs better than other algorithms.

  13. Distributions and concentrations of thallium in surface waters of a region impacted by historical metal mining (Cornwall, UK).

    Science.gov (United States)

    Tatsi, Kristi; Turner, Andrew

    2014-03-01

    Thallium is a highly toxic heavy metal whose concentrations and distributions in the aquatic environment are poorly defined. In this study, concentrations of aqueous and total Tl have been measured in water samples from a variety of rivers and effluents (the latter related to historical metal mining) in the county of Cornwall, SW England. Aqueous concentrations ranged from about 13 ng L(-1) in a river whose catchment contained no metal mines to 2,640 ng L(-1) in water abstracted directly from an abandoned mine shaft. Concentrations of Tl in rivers were greatest in the vicinity of mine-related effluents, with a maximum value measured of about 770 ng L(-1). Thallium was not efficiently removed by the conventional, active treatment of mine water, and displayed little interaction with suspended particles. Its mobility in surface waters, coupled with concentrations that are close to a quality guideline of 800 ng L(-1), is cause for concern. Accordingly, we recommend that the metal is more closely monitored in this and other regions impacted by mining activities. Copyright © 2013 Elsevier B.V. All rights reserved.

  14. Comparison of the Force-, Velocity- and Power-Time Curves Between the Concentric-Only and Eccentric-Concentric Bench Press Exercises.

    Science.gov (United States)

    Pérez-Castilla, Alejandro; Comfort, Paul; McMahon, John J; Pestaña-Melero, Francisco Luis; García-Ramos, Amador

    2018-01-17

    The aim of this study was to compare the temporal and mechanical variables between the concentric-only and eccentric-concentric bench press (BP) variants. Twenty-one men (age: 22.0±4.2 years, body mass: 73.4±7.7 kg, height: 177.2±8.0 cm; one-repetition maximum [1RM]: 1.12±0.12 kg⋅kg) were evaluated during the concentric-only and eccentric-concentric BP variants using 80% 1RM. Temporal (concentric phase duration, propulsive phase duration, and time to reach the maximum values of force, velocity, and power) and mechanical variables (force, velocity, and power), determined using a linear velocity transducer, were compared between both BP variants. All temporal variables were significantly lower during the eccentric-concentric BP compared to the concentric-only BP (P velocity and power were significantly higher for the eccentric-concentric BP compared to the concentric-only BP (all P velocity (ES: 0.40) and power (ES: 0.41). The stretch-shortening cycle (i.e., eccentric-concentric BP) mainly enhanced force production at the early portion of the concentric phase, but this potentiation effect gradually reduced over the latter part of the movement. Finally, force was higher for the concentric-only BP during 49% of the concentric phase duration. These results suggest that both BP variants should be included during resistance training programs in order to optimize force output at different points of the concentric phase.

  15. Last Glacial Maximum CO2 and d13C successfully reconciled

    NARCIS (Netherlands)

    Bouttes, N.; Paillard, D.; Roche, D.M.V.A.P.; Brovkin, V.; Bopp, L.

    2011-01-01

    During the Last Glacial Maximum (LGM, ∼21,000 years ago) the cold climate was strongly tied to low atmospheric CO2 concentration (∼190 ppm). Although it is generally assumed that this low CO2 was due to an expansion of the oceanic carbon reservoir, simulating the glacial level

  16. The maximum theoretical performance of unconcentrated solar photovoltaic and thermoelectric generator systems

    DEFF Research Database (Denmark)

    Bjørk, Rasmus; Nielsen, Kaspar Kirstein

    2017-01-01

    The maximum efficiency for photovoltaic (PV) and thermoelectric generator (TEG) systems without concentration is investigated. Both a combined system where the TEG is mounted directly on the back of the PV and a tandem system where the incoming sunlight is split, and the short wavelength radiation...

  17. Concentration of metals in fishes from Thane and Bassein creeks of Bombay, India

    Digital Repository Service at National Institute of Oceanography (India)

    Krishnamurti, A.J.; Nair, V.R.

    -58% to the total metals accumulated. Maximum concentration of all metals was found either in liver or in alimentary canal with lowest level in muscle tissue. Though metal accumulation was found to be species specific maximum concentrations were found in bottom...

  18. Concentration of trace metals in boreholes in the Ankobra Basin, Ghan

    African Journals Online (AJOL)

    Roughly 25% of the boreholes had manganese concentration higher than 500 mg l-1, which is the WHO maximum acceptable limit for drinking water. The concentration of mercury was higher than 1.0 mg l-1 (WHO maximum acceptable limit) in 60% of the boreholes during the rainy season but below detection limit in the dry ...

  19. A Hybrid Approach using Collaborative filtering and Content based Filtering for Recommender System

    Science.gov (United States)

    Geetha, G.; Safa, M.; Fancy, C.; Saranya, D.

    2018-04-01

    In today’s digital world, it has become an irksome task to find the content of one's liking in an endless variety of content that are being consumed like books, videos, articles, movies, etc. On the other hand there has been an emerging growth among the digital content providers who want to engage as many users on their service as possible for the maximum time. This gave birth to the recommender system comes wherein the content providers recommend users the content according to the users’ taste and liking. In this paper we have proposed a movie recommendation system. A movie recommendation is important in our social life due to its features such as suggesting a set of movies to users based on their interest, or the popularities of the movies. In this paper we are proposing a movie recommendation system that has the ability to recommend movies to a new user as well as the other existing users. It mines movie databases to collect all the important information, such as, popularity and attractiveness, which are required for recommendation. We use content-based and collaborative filtering and also hybrid filtering, which is a combination of the results of these two techniques, to construct a system that provides more precise recommendations concerning movies.

  20. Long-term variation of outdoor radon equilibrium equivalent concentration

    Energy Technology Data Exchange (ETDEWEB)

    Hoetzl, H. [GSF-Forschungszentrum fuer Umwelt und Gesundheit, Inst. fuer Strahlenschutz, Oberschleissheim (Germany); Winkler, R. [GSF-Forschungszentrum fuer Umwelt und Gesundheit, Inst. fuer Strahlenschutz, Oberschleissheim (Germany)

    1994-10-01

    Long-term variation of outdoor radon equilibrium equivalent concentration was investigated from 1982 to 1992 at a semi-natural location 10 km north of Munich, southern Germany. For this period the continuous measurement yielded a long-term average of 8.6 Bq.m{sup -3} (arithmetic mean) and 6.9 Bq.m{sup -3} (geometric mean), from which an average annual effective dose of 0.14 mSv due to outdoor radon can be derived. A long-term trend of the radon concentration was not detectable over the whole period of observation. However, by time series analysis, a long-term cyclic pattern was identified with two maxima (1984-1986, 1989-1991) and two minima (1982-1983, 1987-1988). The seasonal pattern is characterized by an autumn maximum and an early summer minimum. On average, the seasonal maximum in October was found to be higher by a factor of 2 than the June minimum. The diurnal variation of the radon concentration shows a maximum in the early morning and a minimum in the afternoon. On average, this maximum is a factor of 2 higher than the minimum. In the long term a seasonal pattern was observed for diurnal variation, with an average diurnal maximum to minimum ratio of 1.5 in winter compared with 3.5 in the summer months. The radon concentration is correlated with a meteorological parameter (stagnation index) which takes into account horizontal and vertical exchange processes and the wash-out of aerosols in the lower atmosphere. (orig.)

  1. Long-term variation of outdoor radon equilibrium equivalent concentration

    International Nuclear Information System (INIS)

    Hoetzl, H.; Winkler, R.

    1994-01-01

    Long-term variation of outdoor radon equilibrium equivalent concentration was investigated from 1982 to 1992 at a semi-natural location 10 km north of Munich, southern Germany. For this period the continuous measurement yielded a long-term average of 8.6 Bq.m -3 (arithmetic mean) and 6.9 Bq.m -3 (geometric mean), from which an average annual effective dose of 0.14 mSv due to outdoor radon can be derived. A long-term trend of the radon concentration was not detectable over the whole period of observation. However, by time series analysis, a long-term cyclic pattern was identified with two maxima (1984-1986, 1989-1991) and two minima (1982-1983, 1987-1988). The seasonal pattern is characterized by an autumn maximum and an early summer minimum. On average, the seasonal maximum in October was found to be higher by a factor of 2 than the June minimum. The diurnal variation of the radon concentration shows a maximum in the early morning and a minimum in the afternoon. On average, this maximum is a factor of 2 higher than the minimum. In the long term a seasonal pattern was observed for diurnal variation, with an average diurnal maximum to minimum ratio of 1.5 in winter compared with 3.5 in the summer months. The radon concentration is correlated with a meteorological parameter (stagnation index) which takes into account horizontal and vertical exchange processes and the wash-out of aerosols in the lower atmosphere. (orig.)

  2. Methodological aspects of crossover and maximum fat-oxidation rate point determination.

    Science.gov (United States)

    Michallet, A-S; Tonini, J; Regnier, J; Guinot, M; Favre-Juvin, A; Bricout, V; Halimi, S; Wuyam, B; Flore, P

    2008-11-01

    Indirect calorimetry during exercise provides two metabolic indices of substrate oxidation balance: the crossover point (COP) and maximum fat oxidation rate (LIPOXmax). We aimed to study the effects of the analytical device, protocol type and ventilatory response on variability of these indices, and the relationship with lactate and ventilation thresholds. After maximum exercise testing, 14 relatively fit subjects (aged 32+/-10 years; nine men, five women) performed three submaximum graded tests: one was based on a theoretical maximum power (tMAP) reference; and two were based on the true maximum aerobic power (MAP). Gas exchange was measured concomitantly using a Douglas bag (D) and an ergospirometer (E). All metabolic indices were interpretable only when obtained by the D reference method and MAP protocol. Bland and Altman analysis showed overestimation of both indices with E versus D. Despite no mean differences between COP and LIPOXmax whether tMAP or MAP was used, the individual data clearly showed disagreement between the two protocols. Ventilation explained 10-16% of the metabolic index variations. COP was correlated with ventilation (r=0.96, P<0.01) and the rate of increase in blood lactate (r=0.79, P<0.01), and LIPOXmax correlated with the ventilation threshold (r=0.95, P<0.01). This study shows that, in fit healthy subjects, the analytical device, reference used to build the protocol and ventilation responses affect metabolic indices. In this population, and particularly to obtain interpretable metabolic indices, we recommend a protocol based on the true MAP or one adapted to include the transition from fat to carbohydrate. The correlation between metabolic indices and lactate/ventilation thresholds suggests that shorter, classical maximum progressive exercise testing may be an alternative means of estimating these indices in relatively fit subjects. However, this needs to be confirmed in patients who have metabolic defects.

  3. Gentile statistics with a large maximum occupation number

    International Nuclear Information System (INIS)

    Dai Wusheng; Xie Mi

    2004-01-01

    In Gentile statistics the maximum occupation number can take on unrestricted integers: 1 1 the Bose-Einstein case is not recovered from Gentile statistics as n goes to N. Attention is also concentrated on the contribution of the ground state which was ignored in related literature. The thermodynamic behavior of a ν-dimensional Gentile ideal gas of particle of dispersion E=p s /2m, where ν and s are arbitrary, is analyzed in detail. Moreover, we provide an alternative derivation of the partition function for Gentile statistics

  4. Long-term measurement of radon concentration in the family house

    International Nuclear Information System (INIS)

    Muellerova, M.; Holy, K.

    2009-01-01

    The aim of this report was monitored the family house with radon concentration above radon limit for inhabited areas during one year. We were studied radon concentration changes in different rooms this house. Knowledge concerning of variations of radon activity concentration in family house were obtained. Daily variations show a maximum in the morning and a minimum in the afternoon. The seasonal variations show a minimum in spring months (March -April) and a maximum in early autumn (September). The radon concentration in the upstairs room was similar but ten-times lower than radon concentration in the downstairs room. In next period, the obtained results will be analysed in detail and different model describing the behaviour of radon in indoor air will be tested too. (authors)

  5. Designing generalized conic concentrators for conventional optical systems

    Science.gov (United States)

    Eichhorn, W. L.

    1985-01-01

    Generalized nonimaging concentrators can be incorporated into conventional optical systems in situations where flux concentration rather than imaging is required. The parameters of the concentrator for maximum flux concentration depend on the design of the particular optical system under consideration. Rationale for determining the concentrator parameters is given for one particular optical system and the procedure used for calculation of these parameters is outlined. The calculations are done for three concentrators applicable to the optical system.

  6. Health food store recommendations: implications for breast cancer patients

    International Nuclear Information System (INIS)

    Mills, Edward; Ernst, Edzard; Singh, Rana; Ross, Cory; Wilson, Kumanan

    2003-01-01

    Many breast cancer patients use complementary and alternative medicine (CAM). We aimed to determine what advice health food store employees present to individuals seeking treatment options for breast cancer. Eight data gatherers asked employees of all retail health food stores in a major Canadian city, what they recommended for a patient with breast cancer. The data gatherers inquired about product safety, potential drug interactions, costs and efficacy. They also enquired about employee training related to the products. Thirty-four stores were examined. A total of 33 different products were recommended, none of which are supported by sufficient evidence of efficacy. The average cost of the products they recommended was $58.09 (CAD) (minimum $5.28, median $32.99, maximum $600) per month. Twenty-three employees (68%) did not ask whether the patient took prescription medications. Fifteen employees (44%) recommended visiting a healthcare professional (naturopaths (9), physicians (5), nutritionists (1). Three employees (8.8%) discussed potential adverse effects of the products. Eight employees (23.5%) discussed the potential for drug interactions. Two employees (5.9%) suggested a possible cure with the products and one employee (2.9%) suggested discontinuing Tamoxifen. Four employees (11.8%) recommended lifestyle changes and three employees (8.8%) recommended books for further reading on the products. This study draws attention to the heterogeneity of advice provided by natural health food stores to individuals seeking treatments for breast cancer, and the safety and cost implications of some of the products recommended. Physicians should enquire carefully about the use of natural health food products by patients with breast cancer. Regulators need to consider regulations to protect vulnerable patients from incurring significant costs in their purchasing of natural health food products lacking evidence of benefit and of questionable safety

  7. Amikacin Concentrations Predictive of Ototoxicity in Multidrug-Resistant Tuberculosis Patients.

    Science.gov (United States)

    Modongo, Chawangwa; Pasipanodya, Jotam G; Zetola, Nicola M; Williams, Scott M; Sirugo, Giorgio; Gumbo, Tawanda

    2015-10-01

    Aminoglycosides, such as amikacin, are used to treat multidrug-resistant tuberculosis. However, ototoxicity is a common problem and is monitored using peak and trough amikacin concentrations based on World Health Organization recommendations. Our objective was to identify clinical factors predictive of ototoxicity using an agnostic machine learning method. We used classification and regression tree (CART) analyses to identify clinical factors, including amikacin concentration thresholds that predicted audiometry-confirmed ototoxicity among 28 multidrug-resistant pulmonary tuberculosis patients in Botswana. Amikacin concentrations were measured for all patients. The quantitative relationship between predictive factors and the probability of ototoxicity were then identified using probit analyses. The primary predictors of ototoxicity on CART analyses were cumulative days of therapy, followed by cumulative area under the concentration-time curve (AUC), which improved on the primary predictor by 87%. The area under the receiver operating curve was 0.97 on the test set. Peak and trough were not predictors in any tree. When algorithms were forced to pick peak and trough as primary predictors, the area under the receiver operating curve fell to 0.46. Probit analysis revealed that the probability of ototoxicity increased sharply starting after 6 months of therapy to near maximum at 9 months. A 10% probability of ototoxicity occurred with a threshold cumulative AUC of 87,232 days · mg · h/liter, while that of 20% occurred at 120,000 days · mg · h/liter. Thus, cumulative amikacin AUC and duration of therapy, and not peak and trough concentrations, should be used as the primary decision-making parameters to minimize the likelihood of ototoxicity in multidrug-resistant tuberculosis. Copyright © 2015, Modongo et al.

  8. Application of the ICRP recommendations to revised secondary radiation protection standards

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Corley, J.P.

    1988-01-01

    In 1977, the International Commission on Radiological Protection (ICRP) issued Publication No. 26 containing its recommendations for major changes in the conceptual basis for radiation protection. The new recommendations consider total risk (to the whole body) instead of controlling (critical-organ) risk. Subsequent publications and explanatory statements most useful for providing clarification of the intent of the new recommendations have not resolved practical problems encountered in attempting to apply them to either occupational or public exposures. Some of the problems that still exist in applying these recommendations for estimating doses to members of the public include the following: allowance for age differences within an exposed population group, definition of 50-y dose versus lifetime (70-y) dose, definition of negligible risk levels for individual and collective doses, and derivation of appropriate concentration guidelines. The United States is in the process of adopting the revised recommendations of the ICRP. In addition to adopting versions of the primary radiation protection standards, both the U.S. Nuclear Regulatory Commission and the U.S. Department of Energy have developed draft secondary standards that are similar to the Derived Air Concentration values given by the ICRP. This paper presents a brief history of the development of these revised secondary standards, discusses their technical bases, provides a comparison of them, and discusses their limitations and potential misapplication

  9. Applying tracer techniques to NPP liquid effluents for estimating the maximum concentration of soluble pollutants in a man-made canal

    International Nuclear Information System (INIS)

    Varlam, Carmen; Stefanescu, Ioan; Varlam, Mihai; Raceanu, Mircea; Enache, Adrian; Faurescu, Ionut; Patrascu, Vasile; Bucur, Cristina

    2006-01-01

    -October 2002. We established tritium level and tritium concentrations significant for the edge and the tail of tritiated wastewater evacuations. We obtained unit-peak-attenuation (UPA) curve as related to different mixing times using three locations in which we measured tracer-response curves. The UPA curve, along with the time-of travel curves, provides a ready means of predicting maximum soluble contaminant levels that could be experienced at any location in the investigated area. (authors)

  10. Using spatially detailed water-quality data and solute-transport modeling to improve support total maximum daily load development

    Science.gov (United States)

    Walton-Day, Katherine; Runkel, Robert L.; Kimball, Briant A.

    2012-01-01

    Spatially detailed mass-loading studies and solute-transport modeling using OTIS (One-dimensional Transport with Inflow and Storage) demonstrate how natural attenuation and loading from distinct and diffuse sources control stream water quality and affect load reductions predicted in total maximum daily loads (TMDLs). Mass-loading data collected during low-flow from Cement Creek (a low-pH, metal-rich stream because of natural and mining sources, and subject to TMDL requirements) were used to calibrate OTIS and showed spatially variable effects of natural attenuation (instream reactions) and loading from diffuse (groundwater) and distinct sources. OTIS simulations of the possible effects of TMDL-recommended remediation of mine sites showed less improvement to dissolved zinc load and concentration (14% decrease) than did the TMDL (53-63% decrease). The TMDL (1) assumed conservative transport, (2) accounted for loads removed by remediation by subtracting them from total load at the stream mouth, and (3) did not include diffuse-source loads. In OTIS, loads were reduced near their source; the resulting concentration was decreased by natural attenuation and increased by diffuse-source loads during downstream transport. Thus, by not including natural attenuation and loading from diffuse sources, the TMDL overestimated remediation effects at low flow. Use of the techniques presented herein could improve TMDLs by incorporating these processes during TMDL development.

  11. Non-compliance with Australian stock exchange recommendations on board independence

    Directory of Open Access Journals (Sweden)

    Patricia O’Keefe

    2011-11-01

    Full Text Available An agency theory perspective is adopted to explain the high levels of non-compliance with recommendations concerning board structure of the Australian Stock Exchange’s (ASX Corporate Governance Principles and Recommendations. The study compares groups of compliers and non-compliers drawn from members of the ASX All Ordinaries Index. The results indicate that, in the presence of mitigating factors such as less complexity, higher levels of managerial ownership of equity and higher ownership concentration, entities are less likely to comply with the recommendations on board independence. The results suggest that the compliance decision might be influenced by mitigating factors that reduce the need for board independence.

  12. Spatial and temporal variability of fluoride concentrations in groundwater resources of Larestan and Gerash regions in Iran from 2003 to 2010.

    Science.gov (United States)

    Amini, Hassan; Haghighat, Gholam Ali; Yunesian, Masud; Nabizadeh, Ramin; Mahvi, Amir Hossein; Dehghani, Mohammad Hadi; Davani, Rahim; Aminian, Abd-Rasool; Shamsipour, Mansour; Hassanzadeh, Naser; Faramarzi, Hossein; Mesdaghinia, Alireza

    2016-02-01

    There is discrepancy about intervals of fluoride monitoring in groundwater resources by Iranian authorities. Spatial and temporal variability of fluoride in groundwater resources of Larestan and Gerash regions in Iran were analyzed from 2003 to 2010 using a geospatial information system and the Mann-Kendall trend test. The mean concentrations of fluoride for the 8-year period in the eight cities and 31 villages were 1.6 and 2.0 mg/l, respectively; the maximum values were 2.4 and 3.8 mg/l, respectively. Spatial, temporal, and spatiotemporal variability of fluoride in overall groundwater resources were relatively constant over the years. However, results of the Mann-Kendall trend test revealed a monotonic trend in the time series of one city and 11 villages for the 8-year period. Specifically, one city and three villages showed positive significant Kendall's Tau values, suggesting an upward trend in fluoride concentrations over the 8-year period. In contrast, seven villages displayed negative significant Kendall's Tau values, arguing for a downward trend in fluoride concentrations over the years. From 2003 to 2010, approximately 52 % of the Larestan and Gerash areas have had fluoride concentrations above the maximum permissible Iranian drinking water standard fluoride level (1.4 mg/l), and about 116,000 people were exposed to such excess amounts. Therefore, our study supports for a close monitoring of fluoride concentrations from health authorities in monthly intervals, especially in villages and cities that showed positive trend in fluoride concentrations. Moreover, we recommend simultaneous implementation of cost-effective protective measures or interventions until a standard fluoride level is achieved.

  13. Studies of atmospheric pollutants concentration factors from La Reina reactor

    International Nuclear Information System (INIS)

    Vera, I.; Alegria, E.

    1983-01-01

    Results of an atmospheric diffusion model for pollutant gases re shown, in which the nuclear reactor of the La Reina Nuclear Centre is considered as the emitting source. The model uses a gaussian shape steady state cloud of concentration of pollutants and actual topographical and meteorological statistics data os the zone. Expected and maximum probable concentration factors are computed in a polar lattice in 16 wind directions. It was found that peaks for expected concentration factors and maximum probable concentration factors at ground level fall within the N and ESE directions at distances where hills or mountains reach the emitted cloud. A discussion of the practical value of these calculations is given. (Author)

  14. Studies of atmospheric pollutants concentration factors from La Reina reactor

    Energy Technology Data Exchange (ETDEWEB)

    Vera, I; Alegria, E [Comision Chilena de Energia Nuclear, Santiago. Div. de Seguridade Nuclear y Radioproteccion

    1983-11-01

    Results of an atmospheric diffusion model for pollutant gases are shown, in which the nuclear reactor of the La Reina Nuclear Centre is considered as the emitting source. The model uses a gaussian shape steady state cloud of concentration of pollutants and actual topographical and meteorological statistics data of the zone. Expected and maximum probable concentration factors are computed in a polar lattice in 16 wind directions. It was found that peaks for expected concentration factors and maximum probable concentration factors at ground level fall within the N and ESE directions at distances where hills or mountains reach the emitted cloud. A discussion of the practical value of these calculations is given.

  15. Fibrinogen concentrate in bleeding patients

    DEFF Research Database (Denmark)

    Wikkelsø, Anne; Lunde, Jens; Johansen, Mathias

    2013-01-01

    Hypofibrinogenaemia is associated with increased morbidity and mortality, but the optimal treatment level, the use of preemptive treatment and the preferred source of fibrinogen remain disputed. Fibrinogen concentrate is increasingly used and recommended for bleeding with acquired haemostatic...

  16. Concentration of Heavy Metals in Drinking Water from Urban Areas ...

    African Journals Online (AJOL)

    Bheema

    drinking water treatment practices in the areas, which in turn have important human health implications. This study, therefore, recommends the government and other responsible authorities to take appropriate corrective measures. Key words: Drinking water quality, Heavy metals, Maximum admissible limit, World health.

  17. Recommendations for equipment requirements and specifications for digital and interventional radiology: Dosimetric aspects

    International Nuclear Information System (INIS)

    Suliman, I.I.; Zoetelief, J.

    2002-01-01

    The recognition of radiation induced injuries from fluoroscopically guided interventional procedures has resulted in the current demand for development of recommendations and standards to limit dose to both patients and staff. This paper outlines the recommendations drafted within the framework of European Project DIMOND III. The actual work involves survey and review of national and international documents as well as scientific publications in areas relevant to the digital and/or interventional radiology with an aim of developing recommendations for equipment requirements and specifications for digital and interventional radiology. A pilot study of experimental investigations in at least three hospitals will be conducted to test the requirements and the specifications, the result of which will be presented. The recommendations are expected to provide an effective means of dose reduction to both patients and staff while maintaining image quality adequate for the specific diagnosis or interventional procedure. Different components of x-ray systems that have direct impact on patient and staff doses have been considered. Where necessary a compromise between patient dose and image quality has been made. The dosimetric aspects of the recommendations propose detailed descriptions and limits to dosimetric information relevant to patient and staff doses. International recommendations on maximum patient entrance surface dose rate vary in the range from 25 to 65 mGy.min -1 for normal mode fluoroscopy. Maximum image intensifier or image receptor input dose rate around 0.1 Gy min -1 at a distance 30 cm from the image intensifier input surface has been generally recommended. Maximum fluoroscopic dose rate in air must not exceed 50 mGy.min -1 at a location depending on the configuration e.g. for undertable x-ray tube at 10 mm from the patient support on the patient side of the support. The use of pulsed fluoroscopy or low dose fluoroscopy is proposed as good options to minimize

  18. REMOVAL AND CONCENTRATION OF URANIUM FROM WASTE MINE

    Directory of Open Access Journals (Sweden)

    Elizângela Augusta Santos

    2011-01-01

    Full Text Available The use of leaching agents, such as sodium citrate and ammonium carbonate, were assessed for the extraction of uranium from one mining residue containing 0.25% U. Concentration techniques such as precipitation and ion exchange were employed to recover the uranium from the leaching liquor. Leaching results showed maximum uranium extraction of about 40% for both reagents. The use 10 mol L-1 NaOH to precipitate the uranium from the leach liquor leads to a recovery of 62%; what was considered not satisfactory. In view of this, resins were used to concentrate the uranium from the liquor and the metal loading obtained at pH 3.9 was higher for the resin DOWEX RPU, whose maximum loading maximum capacity was 148.3 mg g-1, compared to 126.9 mg g-1 presented by the resin IRA 910 U.

  19. Maximum Mass of Hybrid Stars in the Quark Bag Model

    Science.gov (United States)

    Alaverdyan, G. B.; Vartanyan, Yu. L.

    2017-12-01

    The effect of model parameters in the equation of state for quark matter on the magnitude of the maximum mass of hybrid stars is examined. Quark matter is described in terms of the extended MIT bag model including corrections for one-gluon exchange. For nucleon matter in the range of densities corresponding to the phase transition, a relativistic equation of state is used that is calculated with two-particle correlations taken into account based on using the Bonn meson-exchange potential. The Maxwell construction is used to calculate the characteristics of the first order phase transition and it is shown that for a fixed value of the strong interaction constant αs, the baryon concentrations of the coexisting phases grow monotonically as the bag constant B increases. It is shown that for a fixed value of the strong interaction constant αs, the maximum mass of a hybrid star increases as the bag constant B decreases. For a given value of the bag parameter B, the maximum mass rises as the strong interaction constant αs increases. It is shown that the configurations of hybrid stars with maximum masses equal to or exceeding the mass of the currently known most massive pulsar are possible for values of the strong interaction constant αs > 0.6 and sufficiently low values of the bag constant.

  20. Fibrinogen concentrates for bleeding trauma patients: what is the evidence?

    DEFF Research Database (Denmark)

    Meyer, Martin; Ostrowski, S R; Windeløv, N A

    2011-01-01

    A balanced transfusion of red blood cells, fresh frozen plasma and platelets are recommended for massively bleeding trauma patients. Fibrinogen concentrates could potentially lessen or replace the need for fresh frozen plasma and/or platelet transfusions.......A balanced transfusion of red blood cells, fresh frozen plasma and platelets are recommended for massively bleeding trauma patients. Fibrinogen concentrates could potentially lessen or replace the need for fresh frozen plasma and/or platelet transfusions....

  1. Evaluation of the external radiation exposure dosimetry and calculation of maximum permissible concentration values for airborne materials containing 18F, 15O, 13N, 11C and 133Xe

    International Nuclear Information System (INIS)

    Piltingsrud, H.V.; Gels, G.L.

    1985-01-01

    To better understand the dose equivalent (D.E.) rates produced by airborne releases of gaseous positron-emitting radionuclides under various conditions of cloud size, a study of the external radiation exposure dosimetry of these radionuclides, as well as negatron, gamma and x-ray emitting 133Xe, was undertaken. This included a calculation of the contributions to D.E. as a function of cloud radii, at tissue depths of 0.07 mm (skin), 3 mm (lens of eye) and 10 mm (whole body) from both the particulate and photon radiations emitted by these radionuclides. Estimates of maximum permissible concentration (MPC) values were also calculated based on the calculated D.E. rates and current regulations for personnel radiation protection (CFR84). Three continuous air monitors, designed for use with 133Xe, were evaluated for applications in monitoring air concentrations of the selected positron emitters. The results indicate that for a given radionuclide and for a cloud greater than a certain radius, personnel radiation dosimeters must respond acceptably to only the photon radiations emitted by the radionuclide to provide acceptable personnel dosimetry. For clouds under that radius, personnel radiation dosimeters must also respond acceptably to the positron or negatron radiations to provide acceptable personnel dosimetry. It was found that two out of the three air concentration monitors may be useful for monitoring air concentrations of the selected positron emitters

  2. Cosmic shear measurement with maximum likelihood and maximum a posteriori inference

    Science.gov (United States)

    Hall, Alex; Taylor, Andy

    2017-06-01

    We investigate the problem of noise bias in maximum likelihood and maximum a posteriori estimators for cosmic shear. We derive the leading and next-to-leading order biases and compute them in the context of galaxy ellipticity measurements, extending previous work on maximum likelihood inference for weak lensing. We show that a large part of the bias on these point estimators can be removed using information already contained in the likelihood when a galaxy model is specified, without the need for external calibration. We test these bias-corrected estimators on simulated galaxy images similar to those expected from planned space-based weak lensing surveys, with promising results. We find that the introduction of an intrinsic shape prior can help with mitigation of noise bias, such that the maximum a posteriori estimate can be made less biased than the maximum likelihood estimate. Second-order terms offer a check on the convergence of the estimators, but are largely subdominant. We show how biases propagate to shear estimates, demonstrating in our simple set-up that shear biases can be reduced by orders of magnitude and potentially to within the requirements of planned space-based surveys at mild signal-to-noise ratio. We find that second-order terms can exhibit significant cancellations at low signal-to-noise ratio when Gaussian noise is assumed, which has implications for inferring the performance of shear-measurement algorithms from simplified simulations. We discuss the viability of our point estimators as tools for lensing inference, arguing that they allow for the robust measurement of ellipticity and shear.

  3. Reduction of Nicardipine-Related Phlebitis in Patients with Acute Stroke by Diluting Its Concentration.

    Science.gov (United States)

    Kawada, Kei; Ohta, Tsuyoshi; Tanaka, Koudai; Miyamoto, Norifumi

    2018-03-05

    Nicardipine is frequently used in the treatment of hypertension for patients with acute stroke; however, its dosing is complicated by a high risk of phlebitis. In the present study, we examined whether restricting nicardipine concentration under a specific value could reduce the incidence of nicardipine-related phlebitis in patients with acute stroke. Intravenous nicardipine-related phlebitis was retrospectively analyzed. From July 2015, a simple proposition was made to dilute maximum intravenous nicardipine concentration to lower than 130 µg/mL. The maximum intravenous nicardipine concentration and the incidence of phlebitis were compared between patients treated from July 2014 to June 2015 (preproposition group) and patients treated from July 2015 to June 2016 (postproposition group). A total of 300 patients (preproposition group, 138; postproposition group, 162) were included. The postproposition group demonstrated significantly lower maximum intravenous nicardipine concentration (in µg/mL, 76.9, 47.6-104.5 versus 130.4, 69.8-230.8; P phlebitis (9.9%, 16/162 vs. 30%, 42/138; P phlebitis, which indicated the usefulness of the proposition to dilute maximum intravenous nicardipine concentration to lower than 130 µg/mL. The simple and appropriate proposition about nicardipine administration lowered maximum nicardipine concentration and reduced the incidence of nicardipine-related phlebitis in patients with acute stroke. Copyright © 2018 National Stroke Association. Published by Elsevier Inc. All rights reserved.

  4. Critical evaluation of safety and radiological protection requirements adopted for the transport of uranium and thorium ores and concentrates

    International Nuclear Information System (INIS)

    Mezrahi, Arnaldo; Crispim, Verginia R.

    2009-01-01

    This work evaluates in a critical way the safety and radiological protection recommendations established by the International Atomic Energy Agency - IAEA and adopted national and internationally, for the transport of uranium and thorium ores and concentrates, known according the transport regulations, as being of the Low Specific Activity Material Type-I, LSA-I, basing on more realistic scenarios than the presently existent, aiming at the determination of maximum exposure levels of radiation as well as the maximal contents of those materials in packages and conveyance. A general overview taking into account the scenarios foreseen by the regulations of the IAEA pointed out for a need of a better justification of the requirements edited by the Agency or should be used to support a request of revision of those regulations, national and internationally adopted, in the pertinent aspects to the transport of uranium and thorium ores and concentrates. (author)

  5. Mining and representing recommendations in actively evolving recommender systems

    DEFF Research Database (Denmark)

    Assent, Ira

    2010-01-01

    Recommender systems provide an automatic means of filtering out interesting items, usually based on past similarity of user ratings. In previous work, we have suggested a model that allows users to actively build a recommender network. Users express trust, obtain transparency, and grow (anonymous......) recommender connections. In this work, we propose mining such active systems to generate easily understandable representations of the recommender network. Users may review these representations to provide active feedback. This approach further enhances the quality of recommendations, especially as topics...... of interest change over time. Most notably, it extends the amount of control users have over the model that the recommender network builds of their interests....

  6. Seasonal variation in heavy metal concentration in mangrove foliage

    Digital Repository Service at National Institute of Oceanography (India)

    Untawale, A.G.; Wafar, S.; Bhosle, N.B.

    Seasonal variation in the concentration of some heavy metals in the leaves of seven species of mangrove vegetation from Goa, revealed that maximum concentration of iron and manganese occurs during the monsoon season without any significant toxic...

  7. Continuous measurements of outdoor radon concentrations

    International Nuclear Information System (INIS)

    Iida, T.; Ikebe, Y.; Suzuki, K.; Ueno, K.; Komura, K.; Kato, I.; Jin Yihe

    1993-01-01

    The authors studied and developed an electrostatic 222 Rn monitor and have measured continuously outdoor radon ( 222 Rn) concentrations at Nagoya University since 1985. Four 222 Rn monitors were newly constructed to measure outdoor 222 Rn concentrations at other locations. The 222 Rn concentrations at Nagoya and Kasugai show a clear diurnal variation in autumn, and a seasonal pattern of a spring-summer minimum and a autumn-winter maximum. The results at Toki are the same pattern as that at Nagoya except spring. The concentrations at Kanazawa show a slight seasonal variation. A clear diurnal variation is observed in summer. (4 figs.)

  8. Determination of the maximum MGS mounting height : phase II detailed analysis with LS-DYNA.

    Science.gov (United States)

    2012-12-01

    Determination of the maximum Midwest Guardrail System (MGS) mounting height was performed in two phases. : Phase I concentrated on crash testing: two full-scale crash tests were performed on the MGS with top-rail mounting heights : of 34 in. (864 mm)...

  9. Radon Concentration And Dose Assessment In Well Water Samples From Karbala Governorate Of Iraq

    Science.gov (United States)

    Al-Alawy, I. T.; Hasan, A. A.

    2018-05-01

    There are numerous studies around the world about radon concentrations and their risks to the health of human beings. One of the most important social characteristics is the use of water wells for irrigation, which is a major source of water pollution with radon gas. In the present study, six well water samples have been collected from different locations in Karbala governorate to investigate radon concentration level using CR-39 technique. The maximum value 4.112±2.0Bq/L was in Al-Hurr (Al-Qarih Al-Easariah) region, and the lowest concentration of radon was in Hay Ramadan region which is 2.156±1.4Bq/L, with an average value 2.84±1.65Bq/L. The highest result of annual effective dose (AED) was in Al-Hurr (Al-Qarih Al-Easariah) region which is equal to 15.00±3.9μSv/y, while the minimum was recorded in Hay Ramadan 7.86±2.8μSv/y, with an average value 10.35±3.1μSv/y. The current results have shown that the radon concentrations in well water samples are lower than the recommended limit 11.1Bq/L and the annual effective dose in these samples are lower than the permissible international limit 1mSv/y.

  10. Determination of times maximum insulation in case of internal flooding by pipe break

    International Nuclear Information System (INIS)

    Varas, M. I.; Orteu, E.; Laserna, J. A.

    2014-01-01

    This paper demonstrates the process followed in the preparation of the Manual of floods of Cofrentes NPP to identify the allowed maximum time available to the central in the isolation of a moderate or high energy pipe break, until it affects security (1E) participating in the safe stop of Reactor or in pools of spent fuel cooling-related equipment , and to determine the recommended isolation mode from the point of view of the location of the break or rupture, of the location of the 1E equipment and human factors. (Author)

  11. Project Opalinus Clay: Radionuclide Concentration Limits in the Near-Field of a Repository for Spent Fuel and Vitrified High-Level Waste

    Energy Technology Data Exchange (ETDEWEB)

    Berner, U

    2002-10-01

    The disposal feasibility study currently performed by Nagra includes a succession of quantitative models, aiming at describing the fate of radionuclides potentially escaping from the repository system. In this chain of models the present report provides the so called 'solubility limits' (maximum expected concentrations) for safety relevant radionuclides from SF/HLW wastes, disposed of in a reducing clay (Opalinus Clay, bentonite) environment. Solubility and speciation calculations in bentonite pore waters were performed using the very recently updated Nagra/PSI Chemical Thermodynamic Data Base (TDB) for the majority of the 37 elements addressed as potentially relevant. Particularly for the most relevant actinides, the straightforward applications with this updated TDB yielded results in contradiction to chemical analogy considerations. This was a consequence of incomplete data and called for problem specific TDB extensions, which were evaluated in a separate study. However, a summary of these problem specific extensions is provided in section 4.1. The results presented in this report solely depend on geochemical model calculations. Thus, it is of utmost importance that the underlying data and assumptions are made clear to the reader. In order to ensure traceability, all thermodynamic data not included in the Nagra/PSI TDB are explicitly specified in the report, in order to provide complete documentation for quality assurance and for comprehensibility. In order to clearly distinguish between results derived from data carefully reviewed in the Nagra/PSI TDB and those calculated from 'other' data, the summary of expected maximum concentrations provided in Table 1 includes two columns. The heading CALCULATED provides maximum concentrations based on data fully documented in the updated TDB, whereas maximum concentrations, which include additional problem specific data and/or data from other sources, are given under the heading RECOMMENDED. The

  12. Project Opalinus Clay: Radionuclide Concentration Limits in the Near-Field of a Repository for Spent Fuel and Vitrified High-Level Waste

    International Nuclear Information System (INIS)

    Berner, U.

    2002-10-01

    The disposal feasibility study currently performed by Nagra includes a succession of quantitative models, aiming at describing the fate of radionuclides potentially escaping from the repository system. In this chain of models the present report provides the so called 'solubility limits' (maximum expected concentrations) for safety relevant radionuclides from SF/HLW wastes, disposed of in a reducing clay (Opalinus Clay, bentonite) environment. Solubility and speciation calculations in bentonite pore waters were performed using the very recently updated Nagra/PSI Chemical Thermodynamic Data Base (TDB) for the majority of the 37 elements addressed as potentially relevant. Particularly for the most relevant actinides, the straightforward applications with this updated TDB yielded results in contradiction to chemical analogy considerations. This was a consequence of incomplete data and called for problem specific TDB extensions, which were evaluated in a separate study. However, a summary of these problem specific extensions is provided in section 4.1. The results presented in this report solely depend on geochemical model calculations. Thus, it is of utmost importance that the underlying data and assumptions are made clear to the reader. In order to ensure traceability, all thermodynamic data not included in the Nagra/PSI TDB are explicitly specified in the report, in order to provide complete documentation for quality assurance and for comprehensibility. In order to clearly distinguish between results derived from data carefully reviewed in the Nagra/PSI TDB and those calculated from 'other' data, the summary of expected maximum concentrations provided in Table 1 includes two columns. The heading CALCULATED provides maximum concentrations based on data fully documented in the updated TDB, whereas maximum concentrations, which include additional problem specific data and/or data from other sources, are given under the heading RECOMMENDED. The present study also pays

  13. The tolerance efficiency of Panicum maximum and Helianthus annuus in TNT-contaminated soil and nZVI-contaminated soil.

    Science.gov (United States)

    Jiamjitrpanich, Waraporn; Parkpian, Preeda; Polprasert, Chongrak; Laurent, François; Kosanlavit, Rachain

    2012-01-01

    This study was designed to compare the initial method for phytoremediation involving germination and transplantation. The study was also to determine the tolerance efficiency of Panicum maximum (Purple guinea grass) and Helianthus annuus (Sunflower) in TNT-contaminated soil and nZVI-contaminated soil. It was found that the transplantation of Panicum maximum and Helianthus annuus was more suitable than germination as the initiate method of nano-phytoremediation potting test. The study also showed that Panicum maximum was more tolerance than Helianthus annuus in TNT and nZVI-contaminated soil. Therefore, Panicum maximum in the transplantation method should be selected as a hyperaccumulated plant for nano-phytoremediation potting tests. Maximum tolerance dosage of Panicum maximum to TNT-concentration soil was 320 mg/kg and nZVI-contaminated soil was 1000 mg/kg in the transplantation method.

  14. Maximum Acceleration Recording Circuit

    Science.gov (United States)

    Bozeman, Richard J., Jr.

    1995-01-01

    Coarsely digitized maximum levels recorded in blown fuses. Circuit feeds power to accelerometer and makes nonvolatile record of maximum level to which output of accelerometer rises during measurement interval. In comparison with inertia-type single-preset-trip-point mechanical maximum-acceleration-recording devices, circuit weighs less, occupies less space, and records accelerations within narrower bands of uncertainty. In comparison with prior electronic data-acquisition systems designed for same purpose, circuit simpler, less bulky, consumes less power, costs and analysis of data recorded in magnetic or electronic memory devices. Circuit used, for example, to record accelerations to which commodities subjected during transportation on trucks.

  15. Neutron spectra unfolding with maximum entropy and maximum likelihood

    International Nuclear Information System (INIS)

    Itoh, Shikoh; Tsunoda, Toshiharu

    1989-01-01

    A new unfolding theory has been established on the basis of the maximum entropy principle and the maximum likelihood method. This theory correctly embodies the Poisson statistics of neutron detection, and always brings a positive solution over the whole energy range. Moreover, the theory unifies both problems of overdetermined and of underdetermined. For the latter, the ambiguity in assigning a prior probability, i.e. the initial guess in the Bayesian sense, has become extinct by virtue of the principle. An approximate expression of the covariance matrix for the resultant spectra is also presented. An efficient algorithm to solve the nonlinear system, which appears in the present study, has been established. Results of computer simulation showed the effectiveness of the present theory. (author)

  16. Maximum Power from a Solar Panel

    Directory of Open Access Journals (Sweden)

    Michael Miller

    2010-01-01

    Full Text Available Solar energy has become a promising alternative to conventional fossil fuel sources. Solar panels are used to collect solar radiation and convert it into electricity. One of the techniques used to maximize the effectiveness of this energy alternative is to maximize the power output of the solar collector. In this project the maximum power is calculated by determining the voltage and the current of maximum power. These quantities are determined by finding the maximum value for the equation for power using differentiation. After the maximum values are found for each time of day, each individual quantity, voltage of maximum power, current of maximum power, and maximum power is plotted as a function of the time of day.

  17. Optimal Concentration of Organic Solvents to be Used in the Broth Microdilution Method to Determine the Antimicrobial Activity of Natural Products Against Paenibacillus Larvae

    Directory of Open Access Journals (Sweden)

    Cugnata Noelia Melina

    2017-06-01

    Full Text Available American Foulbrood (AFB is a bacterial disease, caused by Paenibacillus larvae, that affects honeybees (Apis mellifera. Alternative strategies to control AFB are based on the treatment of the beehives with antimicrobial natural substances such as extracts, essential oils and/or pure compounds from plants, honey by-products, bacteria and moulds. The broth microdilution method is currently one of the most widely used methods to determine the minimum inhibitory concentration (MIC of a substance. In this regard, the fact that most natural products, due to their lipophilic nature, must be dissolved in organic solvents or their aqueous mixtures is an issue of major concern because the organic solvent becomes part of the dilution in the incubation medium, and therefore, can interfere with bacterial viability depending on its nature and concentration. A systematic study was carried out to determine by the broth microdilution method the MIC and the maximum non inhibitory concentration (MNIC against P. larvae of the most common organic solvents used to extract or dissolve natural products, i.e. ethanol, methanol, acetonitrile, n-butanol, dimethylsulfoxide, and acidified hydromethanolic solutions. From the MIC and MNIC for each organic solvent, recommended maximum concentrations in contact with P. larvae were established: DMSO 5% (v/v, acetonitrile 7.5% (v/v, ethanol 7.5% (v/v, methanol 12% (v/v, n-butanol 1% (v/v, and methanol-water-acetic acid (1.25:98.71:0.04, v/v/v.

  18. [Ozone concentration distribution of urban].

    Science.gov (United States)

    Yin, Yong-quan; Li, Chang-mei; Ma, Gui-xia; Cui, Zhao-jie

    2004-11-01

    The increase of ozone concentration in urban is one of the most important research topics on environmental science. With the increase of nitrogen oxides and hydrogen-carbon compounds which are exhausted from cars, the ozone concentration in urban is obviously increased on sunlight, and threat of photochemistry smog will be possible. Therefore, it is very important to monitor and study the ozone concentration distribution in urban. The frequency-distribution, diurnal variation and monthly variation of ozone concentration were studied on the campus of Shandong University during six months monitoring. The influence of solar radiation and weather conditions on ozone concentration were discussed. The frequency of ozone concentration less than 200 microg/m3 is 96.88%. The ozone concentration has an obvious diurnal variation. The ozone concentration in the afternoon is higher than in the morning and in the evening. The maximum appears in June, when it is the strong solar radiation and high air-temperature. The weather conditions also influence the ozone concentration. The ozone concentration in clear day is higher than in rainy and cloudy day.

  19. No Dose Adjustment is Recommended for Digoxin, Warfarin, Atorvastatin or a Combination Oral Contraceptive When Coadministered with Dulaglutide.

    Science.gov (United States)

    de la Peña, Amparo; Cui, Xuewei; Geiser, Jeanne; Loghin, Corina

    2017-11-01

    Glucagon-like peptide-1 receptor agonists (GLP-1 RAs) for the treatment of type 2 diabetes mellitus are known to delay gastric emptying (GE). The potential effect of the GLP-1 RA dulaglutide on the pharmacokinetics (PK) of four orally administered drugs and on the pharmacodynamic (PD) effect of warfarin was investigated. In four separate clinical pharmacology studies, digoxin, warfarin, atorvastatin and Ortho-Cyclen ® were orally administered to healthy subjects with and without a subcutaneous dose of dulaglutide 1.5 mg. The effect of dulaglutide coadministration was assessed based on the PK parameters of key analytes. For warfarin PD, the effect of dulaglutide on the international normalized ratio (INR) was evaluated. Areas under the concentration-time curves (AUCs) with and without dulaglutide were similar for all analytes except atorvastatin, where it was reduced by 21%. Maximum concentrations (C max ) were generally lower following coadministration with dulaglutide, with statistically significant reductions (90% confidence intervals of geometric least squares means ratios outside 0.80-1.25) for all analytes except R-warfarin. For all analytes, there was a general trend for the time to C max (t max ) to increase following coadministration with dulaglutide. For warfarin, dulaglutide coadministration had no statistically significant effect on the maximum INR (INR max ); however, a 2% increase in area under the INR curve (AUC INR ) was observed. Dulaglutide did not affect the absorption of the tested medications to a clinically relevant degree. Based on the PK and PD evaluations, no dose adjustments for digoxin, warfarin, atorvastatin and Ortho-Cyclen ® are recommended when coadministered with dulaglutide. NCT01458210, NCT01436201, NCT01432938, and NCT01250834.

  20. Canadian solar export market study. Export policy recommendations

    Energy Technology Data Exchange (ETDEWEB)

    1983-11-01

    This report outlines policies and recommendations on the export of Canadian solar equipment and technology, with a view toward stimulating the domestic solar industry. The current picture is of an industry which is relatively small, operates in a competitive domestic market with low profit margins, and needs assistance in order to break into the world market. A number of recommendations are therefore made on the main thrust of industry and government solar export development activities. An export development program is described which includes a strategy of concentrating on a limited number of product lines, namely: low-temperature solar heating systems for recreational applications, integrated residential water heating systems, prepackaged commercial water heating systems, and industrial pre-heat systems. It is also recommended that this strategy be directed only at a limited number of target countries where the market justifies such activity. Market research, international cooperation agreements, promotional services, and proper export organization are also needed.

  1. Radon in HUD assisted multifamily housing: Policy recommendations to the Congress

    International Nuclear Information System (INIS)

    1991-04-01

    The report complies with Section 1091 of the Stewart B. McKinney Homeless Assistance Amendments Act of 1988 which requires that the HUD Secretary report to the Congress on a recommended policy for addressing radon contamination in specified housing. The housing specified in the Act is virtually all rental housing predominantly for low-income and moderate-income households. Almost all of it is multifamily housing: row houses, walk-up apartment buildings, or high-rise buildings. There is inadequate information on the extent to which excessive concentrations of radon occur above the first floor of multistory buildings and on the variation in radon concentrations in attached houses in the same row. HUD's recommended policy is in the four topic areas specified in the Act: research, education, testing, and mitigation

  2. Recommended action levels for radon in dwellings

    International Nuclear Information System (INIS)

    1988-01-01

    The recommendation made by a group appointed by the Directorate of Public Health, arrives at the conclusion that radon in Norwegian dwellings implies a substantial health problem for the country. For this reason it is recommended that actions should be taken to reduce the radiation exposure from radon in Norway. Upper levels for such actions are set to 200 Bq/m 3 (radon in air of dwellings) for new contructions. For existing dwellings having concentrations of 200 - 800 Bq/m 3 , simple and unexpensive remedial actions to reduce levels are sufficient. When levels exceed 800 Bq/m 3 , more elaborate and costly actions are necessary. An evaluation of the extent of the radon problem in Norway is included, together with a survey of the cost and benefit involved in choosing various levels for remedial actions

  3. Design Criteria for Achieving Low Radon Concentration Indoors

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2016-01-01

    Design criteria for achieving low radon concentration indoors are presented in this paper. The paper suggests three design criteria. These criteria have to be considered at the early stage of the building design phase to meet the latest recommendations from the World Health Organization in most...... countries. The three design criteria are; first, establishing a radon barrier facing the ground; second, lowering the air pressure in the lower zone of the slab on ground facing downwards; third, diluting the indoor air with outdoor air. Three criteria when used can prevent radon infiltration and lower...... the radon concentration in the indoor air. In addition, a cheap and reliable method for measuring the radon concentration in the air indoors is described. The provision on radon in the Danish Building Regulations complies with the latest recommendations from the World Health Organization. Radon can cause...

  4. Magnetic concentration of iron-titanium ore with vanadium concentrate from campo Alegre de Lourdes - Bahia, Brazil

    International Nuclear Information System (INIS)

    Delgado, O.; Silva, F.T. da; Ogasawara, T.; Soares, G.F.

    1988-01-01

    The feasibility studies of magnetic concentration of the Campo Alegre de Lourdes ore were carried out, trying to obtain a maximum recovery of vanadium. As a consequence of the complex nature of the ore, mainly due to the presence of ilmenite as a exolutions in the interior of hematite/martite particles, it was not possible to separate the hematite-ilmenite eficiently, wich would be necessary for obtaining a high grade vanadium concentrate with low titanium content. (author) [pt

  5. Effect of glycine, DL-alanine and DL-2-aminobutyric acid on the temperature of maximum density of water

    International Nuclear Information System (INIS)

    Romero, Carmen M.; Torres, Andres Felipe

    2015-01-01

    Highlights: • Effect of α-amino acids on the temperature of maximum density of water is presented. • The addition of α-amino acids decreases the temperature of maximum density of water. • Despretz constants suggest that the amino acids behave as water structure breakers. • Despretz constants decrease as the number of CH 2 groups of the amino acid increase. • Solute disrupting effect becomes smaller as its hydrophobic character increases. - Abstract: The effect of glycine, DL-alanine and DL-2-aminobutyric acid on the temperature of maximum density of water was determined from density measurements using a magnetic float densimeter. Densities of aqueous solutions were measured within the temperature range from T = (275.65 to 278.65) K at intervals of T = 0.50 K over the concentration range between (0.0300 and 0.1000) mol · kg −1 . A linear relationship between density and concentration was obtained for all the systems in the temperature range considered. The temperature of maximum density was determined from the experimental results. The effect of the three amino acids is to decrease the temperature of maximum density of water and the decrease is proportional to molality according to Despretz equation. The effect of the amino acids on the temperature of maximum density decreases as the number of methylene groups of the alkyl chain becomes larger. The results are discussed in terms of (solute + water) interactions and the effect of amino acids on water structure

  6. Concentration dependent hydrogen diffusion in tungsten

    Energy Technology Data Exchange (ETDEWEB)

    Ahlgren, T., E-mail: tommy.ahlgren@helsinki.fi; Bukonte, L.

    2016-10-15

    The diffusion of hydrogen in tungsten is studied as a function of temperature, hydrogen concentration and pressure using Molecular Dynamics technique. A new analysis method to determine diffusion coefficients that accounts for the random oscillation of atoms around the equilibrium position is presented. The results indicate that the hydrogen migration barrier of 0.25 eV should be used instead of the presently recommended value of 0.39 eV. This conclusion is supported by both experiments and density functional theory calculations. Moreover, the migration volume at the saddle point for H in W is found to be positive: ΔV{sub m} ≈ 0.488 Å{sup 3}, leading to a decrease in the diffusivity at high pressures. At high H concentrations, a dramatic reduction in the diffusion coefficient is observed, due to site blocking and the repulsive H-H interaction. The results of this study indicates that high flux hydrogen irradiation leads to much higher H concentrations in tungsten than expected. - Highlights: • The recommended value of 0.39 eV for the H in W migration barrier should be changed to 0.25 eV. • The random oscillation of atoms around the equilibrium position can be dealt with in diffusion simulations. • Hydrogen diffusion in tungsten is highly concentration dependent.

  7. Methods to homogenize electrochemical concentration cell (ECC ozonesonde measurements across changes in sensing solution concentration or ozonesonde manufacturer

    Directory of Open Access Journals (Sweden)

    T. Deshler

    2017-06-01

    Full Text Available Ozone plays a significant role in the chemical and radiative state of the atmosphere. For this reason there are many instruments used to measure ozone from the ground, from space, and from balloons. Balloon-borne electrochemical cell ozonesondes provide some of the best measurements of the ozone profile up to the mid-stratosphere, providing high vertical resolution, high precision, and a wide geographic distribution. From the mid-1990s to the late 2000s the consistency of long-term records from balloon-borne ozonesondes has been compromised by differences in manufacturers, Science Pump (SP and ENSCI (EN, and differences in recommended sensor solution concentrations, 1.0 % potassium iodide (KI and the one-half dilution: 0.5 %. To investigate these differences, a number of organizations have independently undertaken comparisons of the various ozonesonde types and solution concentrations, resulting in 197 ozonesonde comparison profiles. The goal of this study is to derive transfer functions to allow measurements outside of standard recommendations, for sensor composition and ozonesonde type, to be converted to a standard measurement and thus homogenize the data to the expected accuracy of 5 % (10 % in the stratosphere (troposphere. Subsets of these data have been analyzed previously and intermediate transfer functions derived. Here all the comparison data are analyzed to compare (1 differences in sensor solution composition for a single ozonesonde type, (2 differences in ozonesonde type for a single sensor solution composition, and (3 the World Meteorological Organization's (WMO and manufacturers' recommendations of 1.0 % KI solution for Science Pump and 0.5 % KI for ENSCI. From the recommendations it is clear that ENSCI ozonesondes and 1.0 % KI solution result in higher amounts of ozone sensed. The results indicate that differences in solution composition and in ozonesonde type display little pressure dependence at pressures

  8. Temperature of maximum density and excess thermodynamics of aqueous mixtures of methanol

    Energy Technology Data Exchange (ETDEWEB)

    González-Salgado, D.; Zemánková, K. [Departamento de Física Aplicada, Universidad de Vigo, Campus del Agua, Edificio Manuel Martínez-Risco, E-32004 Ourense (Spain); Noya, E. G.; Lomba, E. [Instituto de Química Física Rocasolano, CSIC, Calle Serrano 119, E-28006 Madrid (Spain)

    2016-05-14

    In this work, we present a study of representative excess thermodynamic properties of aqueous mixtures of methanol over the complete concentration range, based on extensive computer simulation calculations. In addition to test various existing united atom model potentials, we have developed a new force-field which accurately reproduces the excess thermodynamics of this system. Moreover, we have paid particular attention to the behavior of the temperature of maximum density (TMD) in dilute methanol mixtures. The presence of a temperature of maximum density is one of the essential anomalies exhibited by water. This anomalous behavior is modified in a non-monotonous fashion by the presence of fully miscible solutes that partly disrupt the hydrogen bond network of water, such as methanol (and other short chain alcohols). In order to obtain a better insight into the phenomenology of the changes in the TMD of water induced by small amounts of methanol, we have performed a new series of experimental measurements and computer simulations using various force fields. We observe that none of the force-fields tested capture the non-monotonous concentration dependence of the TMD for highly diluted methanol solutions.

  9. Time required to achieve maximum concentration of amikacin in synovial fluid of the distal interphalangeal joint after intravenous regional limb perfusion in horses.

    Science.gov (United States)

    Kilcoyne, Isabelle; Nieto, Jorge E; Knych, Heather K; Dechant, Julie E

    2018-03-01

    OBJECTIVE To determine the maximum concentration (Cmax) of amikacin and time to Cmax (Tmax) in the distal interphalangeal (DIP) joint in horses after IV regional limb perfusion (IVRLP) by use of the cephalic vein. ANIMALS 9 adult horses. PROCEDURES Horses were sedated and restrained in a standing position and then subjected to IVRLP (2 g of amikacin sulfate diluted to 60 mL with saline [0.9% NaCl] solution) by use of the cephalic vein. A pneumatic tourniquet was placed 10 cm proximal to the accessory carpal bone. Perfusate was instilled with a peristaltic pump over a 3-minute period. Synovial fluid was collected from the DIP joint 5, 10, 15, 20, 25, and 30 minutes after IVRLP; the tourniquet was removed after the 20-minute sample was collected. Blood samples were collected from the jugular vein 5, 10, 15, 19, 21, 25, and 30 minutes after IVRLP. Amikacin was quantified with a fluorescence polarization immunoassay. Median Cmax of amikacin and Tmax in the DIP joint were determined. RESULTS 2 horses were excluded because an insufficient volume of synovial fluid was collected. Median Cmax for the DIP joint was 600 μg/mL (range, 37 to 2,420 μg/mL). Median Tmax for the DIP joint was 15 minutes. CONCLUSIONS AND CLINICAL RELEVANCE Tmax of amikacin was 15 minutes after IVRLP in horses and Cmax did not increase > 15 minutes after IVRLP despite maintenance of the tourniquet. Application of a tourniquet for 15 minutes should be sufficient for completion of IVRLP when attempting to achieve an adequate concentration of amikacin in the synovial fluid of the DIP joint.

  10. Comparison of tritium concentrations in rainwater, simulated infiltrating water, and groundwater

    International Nuclear Information System (INIS)

    Ishii, Yoshiyuki; Saito, Masaaki; Imaizumi, Hiroshi; Kato, Norio; Kitaoka, Koichi

    2014-01-01

    The tritium concentration in initial groundwater(i.e., freshly infiltrating rainwater) is necessary for groundwater dating. We collected simulated infiltrating water as the initial groundwater and examined its characteristics for tritium concentration. First, in Tokyo, the tritium concentration of simulated infiltrating water was compared with that of rainwater, atmospheric moisture, groundwater, spring water, and sap water. While rainwater, atmospheric moisture, and simulated infiltrating water remarkably changed month-to-month or with every rainfall event, groundwater and spring water were nearly constant throughout the year. Second, we collected the simulated infiltrating water monthly at four sampling sites widely dispersed across Japan(i.e., Sapporo, Niigata, Tokyo, and Matsuyama) from 2004 to 2010. Sapporo and Niigata showed high tritium concentrations as compared with the relatively low concentrations in Tokyo and Matsuyama. These results indicate that we can obtain annual maximum and minimum concentrations at each site, and that we can estimate the tritium concentration in initial groundwater at each site by using a mixing model composed of these maximum and minimum concentrations. (author)

  11. Sucralfate significantly reduces ciprofloxacin concentrations in serum.

    OpenAIRE

    Garrelts, J C; Godley, P J; Peterie, J D; Gerlach, E H; Yakshe, C C

    1990-01-01

    The effect of sucralfate on the bioavailability of ciprofloxacin was evaluated in eight healthy subjects utilizing a randomized, crossover design. The area under the concentration-time curve from 0 to 12 h was reduced from 8.8 to 1.1 micrograms.h/ml by sucralfate (P less than 0.005). Similarly, the maximum concentration of ciprofloxacin in serum was reduced from 2.0 to 0.2 micrograms/ml (P less than 0.005). We conclude that concurrent ingestion of sucralfate significantly reduces the concentr...

  12. Classification of Recommender Expertise in the Wikipedia Recommender System

    DEFF Research Database (Denmark)

    Jensen, Christian D.; Pilkauskas, Povilas; Lefévre, Thomas

    2011-01-01

    to the quality of articles. The Wikipedia Recommender System (WRS) was developed to help users determine the credibility of articles based on feedback from other Wikipedia users. The WRS implements a collaborative filtering system with trust metrics, i.e., it provides a rating of articles which emphasizes...... an evaluation of four existing knowledge classification schemes with respect to these requirements. This evaluation helped us identify a classification scheme, which we have implemented in the current version of the Wikipedia Recommender System....... feedback from recommenders that the user has agreed with in the past. This exposes the problem that most recommenders are not equally competent in all subject areas. The first WRS prototype did not include an evaluation of the areas of expertise of recommenders, so the trust metric used in the article...

  13. Classification of Recommender Expertise in the Wikipedia Recommender System

    DEFF Research Database (Denmark)

    Jensen, Christian D.; Pilkauskas, Povilas; Lefevre, Thomas

    2011-01-01

    to the quality of articles. The Wikipedia Recommender System (WRS) was developed to help users determine the credibility of articles based on feedback from other Wikipedia users. The WRS implements a collaborative filtering system with trust metrics, i.e., it provides a rating of articles "which emphasizes...... an evaluation of four existing knowledge classification schemes with respect to these requirements. This evaluation helped us identify a classification scheme, which we have implemented in the current version of the Wikipedia Recommender System....... feedback from recommenders that the user has agreed with in the past. This exposes the problem that most recommenders are not equally competent in all subject areas. The first WRS prototype did not include an evaluation of the areas of expertise of recommenders, so the trust metric used in the article...

  14. Concentrations of 226Ra and 210Pb in agricultural products surrounding the first brazilian mine and mill in Pocos de Caldas, MG

    International Nuclear Information System (INIS)

    Vasconcellos, L.M.H.; Amaral, E.C.S.; Vianna, E.C.M.

    1989-01-01

    As a complement to the pre-operational environmental monitoring program of the Brazilian first uranium mine and mill, a survey of 226 Ra and 210 Pb in agriculture products, and in the corresponding soils, were carried out in the Pocos de Caldas Plateau. The survey intended to determine site specific transfer factors, in order to better estimate radiation doses on the population. Resulting from the plant operation. In local soils, 226 Ra and 210 Pb have similar concentrations. The average contents are comparable to the values found in areas of normal radioactivity, but the maximum values are higher by one order of magnitude. In the vegetables analyzed (beans, carrot, corn and potato), 226 Ra concentrations are slightly higher than those of 210 Pb, and the maximum values are also one order of magnitude greater than in normal regions. For both radionuclides, the average soil-to-plant transfer factors are of the order of 10 -3 and 10 -2 , when related to total and to exchangeable contents in soils, respectively. These results led to the conclusion that 226 Ra and 210 Pb have similar importance, concerning the population exposure via the foodstuff ingestion pathway. Therefore, it was recommended to carry on routine monitoring program for both radionuclides in the main agriculture crops. However, the naturally elevated radionuclide concentrations, in some local vegetables, will decrease the sensitivity for detecting small increments resulting from the plant operation. (author) [pt

  15. Feasibility of the Two-Point Method for Determining the One-Repetition Maximum in the Bench Press Exercise.

    Science.gov (United States)

    García-Ramos, Amador; Haff, Guy Gregory; Pestaña-Melero, Francisco Luis; Pérez-Castilla, Alejandro; Rojas, Francisco Javier; Balsalobre-Fernández, Carlos; Jaric, Slobodan

    2017-09-05

    This study compared the concurrent validity and reliability of previously proposed generalized group equations for estimating the bench press (BP) one-repetition maximum (1RM) with the individualized load-velocity relationship modelled with a two-point method. Thirty men (BP 1RM relative to body mass: 1.08 0.18 kg·kg -1 ) performed two incremental loading tests in the concentric-only BP exercise and another two in the eccentric-concentric BP exercise to assess their actual 1RM and load-velocity relationships. A high velocity (≈ 1 m·s -1 ) and a low velocity (≈ 0.5 m·s -1 ) was selected from their load-velocity relationships to estimate the 1RM from generalized group equations and through an individual linear model obtained from the two velocities. The directly measured 1RM was highly correlated with all predicted 1RMs (r range: 0.847-0.977). The generalized group equations systematically underestimated the actual 1RM when predicted from the concentric-only BP (P <0.001; effect size [ES] range: 0.15-0.94), but overestimated it when predicted from the eccentric-concentric BP (P <0.001; ES range: 0.36-0.98). Conversely, a low systematic bias (range: -2.3-0.5 kg) and random errors (range: 3.0-3.8 kg), no heteroscedasticity of errors (r 2 range: 0.053-0.082), and trivial ES (range: -0.17-0.04) were observed when the prediction was based on the two-point method. Although all examined methods reported the 1RM with high reliability (CV≤5.1%; ICC≥0.89), the direct method was the most reliable (CV<2.0%; ICC≥0.98). The quick, fatigue-free, and practical two-point method was able to predict the BP 1RM with high reliability and practically perfect validity, and therefore we recommend its use over generalized group equations.

  16. Population pharmacokinetics and maximum a posteriori probability Bayesian estimator of abacavir: application of individualized therapy in HIV-infected infants and toddlers.

    NARCIS (Netherlands)

    Zhao, W.; Cella, M.; Pasqua, O. Della; Burger, D.M.; Jacqz-Aigrain, E.

    2012-01-01

    WHAT IS ALREADY KNOWN ABOUT THIS SUBJECT: Abacavir is used to treat HIV infection in both adults and children. The recommended paediatric dose is 8 mg kg(-1) twice daily up to a maximum of 300 mg twice daily. Weight was identified as the central covariate influencing pharmacokinetics of abacavir in

  17. Patch test concentrations (doses in mg/cm(2) ) for the 12 non-mix fragrance substances regulated by European legislation

    DEFF Research Database (Denmark)

    Bruze, Magnus; Svedman, Cecilia; Andersen, Klaus Ejner

    2012-01-01

    Background. According to EU legislation, 26 fragrance substance allergens must be labelled on cosmetic products. For 12 of them, the optimal patch test concentration/dose has not been evaluated. Objectives. To establish the optimal patch test doses in mg/cm(2) for the 12 fragrance substances......, it is recommended that half of the maximum patch test dose (mg/cm(2) ) be used for aimed and screening patch testing....... that are not included in fragrance mix I or II in the European baseline patch test series. Materials and Methods. Patch testing with the 12 fragrance substances was performed in a stepwise manner encompassing up to five rounds in at least 100 dermatitis patients for each round. Before patch testing, an individual...

  18. Analysis of radon concentrations in drinking water in Erbil governorate (Iraqi Kurdistan) and its health effects

    International Nuclear Information System (INIS)

    Ismail, Asaad H.; Haji, Salih O.

    2008-01-01

    Full text: This paper presents the results of radon level in drinking water in Erbil governorate and its districts. The measurements were carried out on 42 samples (tap water) of 21 major areas, and alpha track detectors (type Cr-39) were used for the estimations. The average values for radon concentration of tap water were variable from the district to another, and it was found to be (4.693±2.213 Bq/L) with a maximum of 9.61 Bq/L in Hugran region and minimum of 2.01 Bq/L in Haji-Omaran city. In addition, the average annual effective doses, and equilibrium factor between radon and its daughter were measured in each area and it was found to be (11.546±8.566 μSv/Yr) and (0.204±0.06) respectively. On the other hand, this paper presents an evaluation of the inhalation and ingestion doses from exposure to radon and also the contribution of radon concentration in drinking water to indoor radon concentration was estimated. When the results were compared with the internationally recommended reference levels (U.S Environmental Protection Agency limit 11.1 Bq/l), there were no indications of existence of radon problems in the water sources in this survey. Therefore the drinking water in Erbil governorate is safe as far as radon concentration is concerned. (author)

  19. 40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

    Science.gov (United States)

    2010-07-01

    ... cylinders having an internal diameter of 13.0 cm and a 15.5 cm stroke length, the rounded displacement would... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Maximum engine power, displacement... Maximum engine power, displacement, power density, and maximum in-use engine speed. This section describes...

  20. Credal Networks under Maximum Entropy

    OpenAIRE

    Lukasiewicz, Thomas

    2013-01-01

    We apply the principle of maximum entropy to select a unique joint probability distribution from the set of all joint probability distributions specified by a credal network. In detail, we start by showing that the unique joint distribution of a Bayesian tree coincides with the maximum entropy model of its conditional distributions. This result, however, does not hold anymore for general Bayesian networks. We thus present a new kind of maximum entropy models, which are computed sequentially. ...

  1. Continuous protein concentration via free-flow moving reaction boundary electrophoresis.

    Science.gov (United States)

    Kong, Fanzhi; Zhang, Min; Chen, Jingjing; Fan, Liuyin; Xiao, Hua; Liu, Shaorong; Cao, Chengxi

    2017-07-28

    In this work, we developed the model and theory of free-flow moving reaction boundary electrophoresis (FFMRB) for continuous protein concentration for the first time. The theoretical results indicated that (i) the moving reaction boundary (MRB) can be quantitatively designed in free-flow electrophoresis (FFE) system; (ii) charge-to-mass ratio (Z/M) analysis could provide guidance for protein concentration optimization; and (iii) the maximum processing capacity could be predicted. To demonstrate the model and theory, three model proteins of hemoglobin (Hb), cytochrome C (Cyt C) and C-phycocyanin (C-PC) were chosen for the experiments. The experimental results verified that (i) stable MRBs with different velocities could be established in FFE apparatus with weak acid/weak base neutralization reaction system; (ii) proteins of Hb, Cyt C and C-PC were well concentrated with FFMRB; and (iii) a maximum processing capacity and recovery ratio of Cyt C enrichment were 126mL/h and 95.5% respectively, and a maximum enrichment factor was achieved 12.6 times for Hb. All of the experiments demonstrated the protein concentration model and theory. In contrast to other methods, the continuous processing ability enables FFMRB to efficiently enrich diluted protein or peptide in large volume solution. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Maximum total organic carbon limit for DWPF melter feed

    International Nuclear Information System (INIS)

    Choi, A.S.

    1995-01-01

    DWPF recently decided to control the potential flammability of melter off-gas by limiting the total carbon content in the melter feed and maintaining adequate conditions for combustion in the melter plenum. With this new strategy, all the LFL analyzers and associated interlocks and alarms were removed from both the primary and backup melter off-gas systems. Subsequently, D. Iverson of DWPF- T ampersand E requested that SRTC determine the maximum allowable total organic carbon (TOC) content in the melter feed which can be implemented as part of the Process Requirements for melter feed preparation (PR-S04). The maximum TOC limit thus determined in this study was about 24,000 ppm on an aqueous slurry basis. At the TOC levels below this, the peak concentration of combustible components in the quenched off-gas will not exceed 60 percent of the LFL during off-gas surges of magnitudes up to three times nominal, provided that the melter plenum temperature and the air purge rate to the BUFC are monitored and controlled above 650 degrees C and 220 lb/hr, respectively. Appropriate interlocks should discontinue the feeding when one or both of these conditions are not met. Both the magnitude and duration of an off-gas surge have a major impact on the maximum TOC limit, since they directly affect the melter plenum temperature and combustion. Although the data obtained during recent DWPF melter startup tests showed that the peak magnitude of a surge can be greater than three times nominal, the observed duration was considerably shorter, on the order of several seconds. The long surge duration assumed in this study has a greater impact on the plenum temperature than the peak magnitude, thus making the maximum TOC estimate conservative. Two models were used to make the necessary calculations to determine the TOC limit

  3. Air Pollution Modelling to Predict Maximum Ground Level Concentration for Dust from a Palm Oil Mill Stack

    Directory of Open Access Journals (Sweden)

    Regina A. A.

    2010-12-01

    Full Text Available The study is to model emission from a stack to estimate ground level concentration from a palm oil mill. The case study is a mill located in Kuala Langat, Selangor. Emission source is from boilers stacks. The exercise determines the estimate the ground level concentrations for dust to the surrounding areas through the utilization of modelling software. The surround area is relatively flat, an industrial area surrounded by factories and with palm oil plantations in the outskirts. The model utilized in the study was to gauge the worst-case scenario. Ambient air concentrations were garnered calculate the increase to localized conditions. Keywords: emission, modelling, palm oil mill, particulate, POME

  4. Maximum Entropy in Drug Discovery

    Directory of Open Access Journals (Sweden)

    Chih-Yuan Tseng

    2014-07-01

    Full Text Available Drug discovery applies multidisciplinary approaches either experimentally, computationally or both ways to identify lead compounds to treat various diseases. While conventional approaches have yielded many US Food and Drug Administration (FDA-approved drugs, researchers continue investigating and designing better approaches to increase the success rate in the discovery process. In this article, we provide an overview of the current strategies and point out where and how the method of maximum entropy has been introduced in this area. The maximum entropy principle has its root in thermodynamics, yet since Jaynes’ pioneering work in the 1950s, the maximum entropy principle has not only been used as a physics law, but also as a reasoning tool that allows us to process information in hand with the least bias. Its applicability in various disciplines has been abundantly demonstrated. We give several examples of applications of maximum entropy in different stages of drug discovery. Finally, we discuss a promising new direction in drug discovery that is likely to hinge on the ways of utilizing maximum entropy.

  5. Lipid needs of preterm infants: updated recommendations.

    Science.gov (United States)

    Lapillonne, Alexandre; Groh-Wargo, Sharon; Gonzalez, Carlos H Lozano; Uauy, Ricardo

    2013-03-01

    Long-chain polyunsaturated fatty acids (LCPUFAs) are of nutritional interest because they are crucial for normal development of the central nervous system and have potential long-lasting effects that extend beyond the period of dietary insufficiency. Here we review the recent literature and current recommendations regarding LCPUFAs as they pertain to preterm infant nutrition. In particular, findings that relate to fetal accretion, LCPUFA absorption and metabolism, effects on development, and current practices and recommendations have been used to update recommendations for health care providers. The amounts of long-chain polyunsaturated fatty acids (LCPUFAs) used in early studies were chosen to produce the same concentrations as in term breast milk. This might not be a wise approach for preterm infants, however, particularly for very and extremely preterm infants, whose requirements for LCPUFAs and other nutrients exceed what is normally provided in the small volumes that they are able to tolerate. Recent studies have reported outcome data in preterm infants fed milk with a docosahexaenoic acid (DHA) content 2-3 times higher than the current concentration in infant formulas. Overall, these studies show that providing larger amounts of DHA supplements, especially to the smallest infants, is associated with better neurologic outcomes in early life. We emphasize that current nutritional management might not provide sufficient amounts of preformed DHA during the parenteral and enteral nutrition periods and in very preterm/very low birth weight infants until their due date, and that greater amounts than used routinely likely will be needed to compensate for intestinal malabsorption, DHA oxidation, and early deficit. Research should continue to address the gaps in knowledge and further refine adequate intake for each group of preterm infants. Copyright © 2013 Mosby, Inc. All rights reserved.

  6. Maximum Quantum Entropy Method

    OpenAIRE

    Sim, Jae-Hoon; Han, Myung Joon

    2018-01-01

    Maximum entropy method for analytic continuation is extended by introducing quantum relative entropy. This new method is formulated in terms of matrix-valued functions and therefore invariant under arbitrary unitary transformation of input matrix. As a result, the continuation of off-diagonal elements becomes straightforward. Without introducing any further ambiguity, the Bayesian probabilistic interpretation is maintained just as in the conventional maximum entropy method. The applications o...

  7. Effects of different photoperiods and concentrations of phosphate on ...

    African Journals Online (AJOL)

    The maximum growth rates were observed in the group treated with 2 fold PO4 concentration. The strategy of growth in this species may depend on nitrogen fixation, when other algae were nitrogen limited and fast PO4 uptake even if very low concentration is available. Key words: Cyanobacteria, Cylindrospermopsis ...

  8. Concentration and solidification of liquid radioactive wastes. Laboratory studies

    International Nuclear Information System (INIS)

    Nuche Vazquez, F.; Lora Soria, F. de

    1969-01-01

    Bench scale runs on concentration of intermediate level radioactive wastes, and incorporation of the concentrates in asphalt, are described. The feasibility of the process has been demonstrated, with a maximum incorporation of 60 percent of salts into the asphaltic matrix and a volume reduction factor of 10. (Author) 14 refs

  9. Formaldehyde concentration in diagnostic patch testing

    DEFF Research Database (Denmark)

    Trattner, A; Johansen, J D; Menné, T

    1998-01-01

    Exposure to formaldehyde is common from both consumer products and industry. The reliability of the patch test is essential for the diagnosis of formaldehyde allergy as it is difficult to suspect from the patient's history. The recommended formaldehyde patch test concentration has been reduced over...

  10. Weighted Maximum-Clique Transversal Sets of Graphs

    OpenAIRE

    Chuan-Min Lee

    2011-01-01

    A maximum-clique transversal set of a graph G is a subset of vertices intersecting all maximum cliques of G. The maximum-clique transversal set problem is to find a maximum-clique transversal set of G of minimum cardinality. Motivated by the placement of transmitters for cellular telephones, Chang, Kloks, and Lee introduced the concept of maximum-clique transversal sets on graphs in 2001. In this paper, we study the weighted version of the maximum-clique transversal set problem for split grap...

  11. Maximum power demand cost

    International Nuclear Information System (INIS)

    Biondi, L.

    1998-01-01

    The charging for a service is a supplier's remuneration for the expenses incurred in providing it. There are currently two charges for electricity: consumption and maximum demand. While no problem arises about the former, the issue is more complicated for the latter and the analysis in this article tends to show that the annual charge for maximum demand arbitrarily discriminates among consumer groups, to the disadvantage of some [it

  12. Thin-source concentration dependent diffusion

    International Nuclear Information System (INIS)

    Eng, G.

    1978-01-01

    The diffusion of (Ca ++ ) in NaCl has been measured for various diffusion times and for the temperature range (575 0 to 775 0 C), using a thin-source of 45 Ca tracer, rectangular geometry, and serial sectioning. The pre-diffusion surface concentration was approximately 3 x 10 16 (Ca)-atoms/cm 2 , which, for an average penetration depth of 100 to 300 μm, produces a maximum (post-diffusion) impurity concentration comparable to or greater than the intrinsic cation vacancy concentration. The high-temperature function closely matches the D 0 (T) function obtained from low impurity concentration experiments. The lower-temperature function, combined with the sudden failure of the D(C) = D 0 (1 + [C] + 0.5[C] 2 ) function at these lower temperatures, indicates the onset of a second diffusion process, one which would operate only at extremely high impurity concentrations. This low-temperature behavior is shown to be consistent with a breakdown of the conditions assumed for vacancy equilibrium

  13. Kinetics of ethanol production by immobilized Kluyveromyces marxianus cells at varying sugar concentrations of Jerusalem artichoke juice

    Energy Technology Data Exchange (ETDEWEB)

    Bajpai, P.; Margaritis, A.

    1987-08-01

    Kinetics of ethanol fermentation at varying sugar concentrations of Jerusalem artichoke tuber extract has been studied using Kluyveromyces marxianus cells immobilized in calcium alginate gel beads. A maximum ethanol concentration of 111 g/l was achieved at an initial sugar concentration of 260 g/l in 20 hours, when the immobilized cell concentration in the calcium alginate beads was 53.3 g dry wt./l bead volume. Ethanol yield remained almost unaffected by initial sugar concentration up to 250 g/l and was found to be about 88% of the theoretical. Maximum rate of ethanol production decreased from 22.5 g ethanol/l/h to 10.5 g ethanol/l/h while the maximum rate of total sugars utilization decreased from 74.9 g sugars/l/h to 28.5 g sugars/l/h as the initial substrate concentration was increased from 100 to 300 g/l. The concentration of free cells in the fermentation broth was low.

  14. Total mercury concentration in common fish species of Lake Victoria ...

    African Journals Online (AJOL)

    Total mercury (THg) concentration was analysed in muscles of common fish species of Lake Victoria in the eastern and southern parts of the lake using cold vapour Atomic Absorption Spectrophotometric technique. Mercury concentration in all fish species was generally lower than the WHO maximum allowable ...

  15. Concentration and purification of plutonium solutions by means of ion-exchange columns

    Energy Technology Data Exchange (ETDEWEB)

    Durham, R W; Aikin, A M

    1953-02-15

    Equilibrium experiments using Dowex 50 ion-exchange resin and nitric acid solutions of Pu{sup 3+}, UO{sub 2}{sup 2+}, Fe{sup 2+} cations have yielded values for the absorption affinities for these ions. Trivalent plutonium was found to be far more strongly absorbed than UO{sub 2}{sup 2+} and Fe{sup 2+}. Column studies have shown that uranium can be completely separated from plutonium even when the initial concentration of uranium is very much greater than that of the plutonium. A plutonium concentration increase of about fifty-fold can be obtained from solutions about 10{sup -3} M in plutonium and 1.0M in nitric acid. The equation K{sub Pu}{sup 3+} = X{sub R} (1-X{sub S}){sup 3} C{sub S}{sup 2}/X{sub S} (1-X{sub R}){sup 3} C{sub R}{sup 2} for estimating the maximum amount of plutonium taken up by a column of resin of unit volume from a solution of total equivalent concentration, C{sub S} , has been shown to hold for values of C{sub S} up to 3 equivalents per litre. X{sub R}, the equivalent fraction of plutonium on the resin, is the number of equivalents of plutonium absorbed by the resin divided by the total capacity of the column. X{sub S}, the equivalent fraction of plutonium in solution, is the equivalent concentration of plutonium divided by the total equivalent concentration of cations in solution. C{sub R} is the total capacity of the resin in milli-equivalents per gram of dry resin. Recommendations have been made for the application and operation of ion-exchange columns in the Plutonium-Extraction Plant. (author)

  16. Experimental characterization of a concentrating photovoltaic system varying the light concentration

    International Nuclear Information System (INIS)

    Renno, C.; Petito, F.; Landi, G.; Neitzert, H.C.

    2017-01-01

    Highlights: • Experimental characterization of a concentrating photovoltaic system. • Analysis of the point-focus concentrating system performances. • Photovoltaic system parameters as function of the concentration factor. - Abstract: The concentrating photovoltaic system represents one of the most promising solar technologies because it allows a more efficient energy conversion. When a CPV system is designed, the main parameter which has to be considered is the concentration factor that affects both the system energy performances and its configuration. An experimental characterization of a CPV system previously realized at the University of Salerno, is presented in this paper considering several aspects related to the optical configuration, the concentration factor and the solar cell used. In particular, the parameters of an Indium Gallium Phosphide/Gallium Arsenide/Germanium triple-junction solar cell are investigated as function of the concentration factor determined by means of an experimental procedure that uses different optical configurations. The maximum concentration factor reached by the CPV system is 310 suns. The cell parameters dependence on the concentration is reported together with an electroluminescence analysis of the Indium Gallium Phosphide/Gallium Arsenide/Germanium cell. A monitoring of the electrical power provided by the system during its working is also presented corresponding to different direct irradiance values. A mean power of 2.95 W with an average efficiency of 32.8% is obtained referring to a mean irradiance of 930 W/m"2; lower values are obtained when the irradiance is highly fluctuating. The concentrating photovoltaic system electric energy output is estimated considering different concentration levels; the maximal obtained value is 23.5 W h on a sunny day at 310×. Finally, the temperature of the triple-junction solar cell is evaluated for different months in order to evaluate the potential annual thermal energy production

  17. Design optimization studies for nonimaging concentrating solar collector tubes

    Science.gov (United States)

    Winston, R.; Ogallagher, J. J.

    1983-09-01

    The Integrated Stationary Evacuated Concentrator or ISEC solar collector panel which achieved the best high temperature performance ever measured with a stationary collector was examined. A development effort review and optimize the initial proof of concept design was completed. Changes in the optical design to improve the angular response function and increase the optical efficiency were determined. A recommended profile design with a concentration ratio of 1.55x and an acceptance angle of + - 35(0) was identified. Two alternative panel/module configurations are recommended based on the preferred double ended flow through design. Parasitic thermal and pumping losses show to be reducible to acceptable levels, and two passive approaches to the problem of ensuring stagnation survival are identified.

  18. Effects of water treatment processes used at waterworks on natural radionuclide concentrations

    International Nuclear Information System (INIS)

    Haemaelaeinen, K.; Vesterbacka, P.; Maekelaeinen, I.; Arvela, H.

    2004-08-01

    The occurrence of uranium and other natural radionuclides in waters of waterworks and the effects of the conventional water treatment processes on radionuclide concentrations were investigated. Water samples were collected from 17 waterworks. Radionuclide concentrations of the collected samples were compared to the currently valid concentrations according to the Finnish regulation, ST guide 12.3. Similarly the measured concentrations were compared to the values presented in the 98/83/EC directive and in the Commission recommendation, 2001/928/Euratom. The guidelines based on chemical toxicity of uranium were also considered. This report presents a summary of the radionuclide concentrations in waters distributed by waterworks. Short-term and logn-term temporal variation of radionuclide levels in raw water were also investigated. Waterworks selected to this study used different kinds of raw water sources and a variety of water treatment processes. Water samples were collected from 46 water catchments which used groundwater in soil, artificial groundwater or groundwater in bedrock as a source of raw water. The most common water treatment used in these catchments was alkalization. Other treatment processes used were various types of filtrations (sand, anthracite, slow sand and membrane filtration) and aeration. Four of the catchments distributed water without treatment. Sampling was carried out in co-operation with local health inspectors and waterworks staff in spring 2002. Later that autumn, monitoring samples were collected from eight catchments. The maximum value for radon, presented in ST guide 12.3, was exceeded in three water catchments that used groundwater in bedrock as a source of raw water. No exceedings were found in those water catchments that use groundwater in soil or artificial groundwater. The limits of uranium and radium calculated from the total indicative dose (98/83/EC) were not exceeded but the guidelines for lead and polonium, given in the

  19. 49 CFR 230.24 - Maximum allowable stress.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Maximum allowable stress. 230.24 Section 230.24... Allowable Stress § 230.24 Maximum allowable stress. (a) Maximum allowable stress value. The maximum allowable stress value on any component of a steam locomotive boiler shall not exceed 1/4 of the ultimate...

  20. Glass Composition Constraint Recommendations for Use in Life-Cycle Mission Modeling

    Energy Technology Data Exchange (ETDEWEB)

    McCloy, John S.; Vienna, John D.

    2010-05-03

    The component concentration limits that most influence the predicted Hanford life-cycle HLW glass volume by HTWOS were re-evaluated. It was assumed that additional research and development work in glass formulation and melter testing would be performed to improve the understanding of component effects on the processability and product quality of these HLW glasses. Recommendations were made to better estimate the potential component concentration limits that could be applied today while technology development is underway to best estimate the volume of HLW glass that will eventually be produced at Hanford. The limits for concentrations of P2O5, Bi2O3, and SO3 were evaluated along with the constraint used to avoid nepheline formation in glass. Recommended concentration limits were made based on the current HLW glass property models being used by HTWOS (Vienna et al. 2009). These revised limits are: 1) The current ND should be augmented by the OB limit of OB ≤ 0.575 so that either the normalized silica (NSi) is less that the 62% limit or the OB is below the 0.575 limit. 2) The mass fraction of P2O5 limit should be revised to allow for up to 4.5 wt%, depending on CaO concentrations. 3) A Bi2O3 concentration limit of 7 wt% should be used. 4) The salt accumulation limit of 0.5 wt% SO3 may be increased to 0.6 wt%. Again, these revised limits do not obviate the need for further testing, but make it possible to more accurately predict the impact of that testing on ultimate HLW glass volumes.

  1. Validation of predicted exponential concentration profiles of chemicals in soils

    International Nuclear Information System (INIS)

    Hollander, Anne; Baijens, Iris; Ragas, Ad; Huijbregts, Mark; Meent, Dik van de

    2007-01-01

    Multimedia mass balance models assume well-mixed homogeneous compartments. Particularly for soils, this does not correspond to reality, which results in potentially large uncertainties in estimates of transport fluxes from soils. A theoretically expected exponential decrease model of chemical concentrations with depth has been proposed, but hardly tested against empirical data. In this paper, we explored the correspondence between theoretically predicted soil concentration profiles and 84 field measured profiles. In most cases, chemical concentrations in soils appear to decline exponentially with depth, and values for the chemical specific soil penetration depth (d p ) are predicted within one order of magnitude. Over all, the reliability of multimedia models will improve when they account for depth-dependent soil concentrations, so we recommend to take into account the described theoretical exponential decrease model of chemical concentrations with depth in chemical fate studies. In this model the d p -values should estimated be either based on local conditions or on a fixed d p -value, which we recommend to be 10 cm for chemicals with a log K ow > 3. - Multimedia mass model predictions will improve when taking into account depth dependent soil concentrations

  2. Design investigation and evaluation of low cost line concentrated solar cooker

    Energy Technology Data Exchange (ETDEWEB)

    Sarvoththama Jothi, T.J. [SASTRA Deemed Univ., Tirumalaisamudram, Thanjavur (India). School of Mechanical Engineering

    2004-07-01

    Enormous amount of energy is wasted in the form of heat for the purpose of cooking all around the world. Broad ranges of technologies are required around the world to incorporate the energy required for cooking. We have efficiently designed and developed a device named Line Concentrated Solar Cooker for the purpose of cooking and heating water or even pasteurization of drinking water. It is distinct from other type of cooker that is using the same old technologies. More over this device can be constructed by means of an inexpensive, commonly available material, thus providing a low-cost option suitable for household use in the developing world. This device was mainly designed from the input taken from the houses of four members each at various places. Its design and performance were evaluated at the laboratory including the efficiency tests. A model of such device was developed which gave the maximum efficiency of around 27 %. This Line Concentrated Solar Cooker has been mainly designed to prevent tracking mechanism, which is the main draw back for other concentrated type solar cooker. In order to prevent tracking mechanism, the design has been made in such a manner that the maximum sunrays are impinging on the reflecting surface of the Line Concentrated Solar Cooker all the time. Hence, minimum of at least 35 percent of the area of the Line Concentrated Solar Cooker is exposed to the sunlight at 8:00 AM and maximum of 100 percentage by noon and gradually decreases by evening as the sun sets. This model gave us a good results leading to excellent heating effect from morning to evening. Hence the heating effect gradually increased from morning to maximum at noon. (orig.)

  3. The maximum temperature of a thermodynamic cycle effect on weight-dimensional characteristics of the NPP energy blocks with air cooling

    International Nuclear Information System (INIS)

    Bezborodov, Yu.A.; Bubnov, V.P.; Nesterenko, V.B.

    1982-01-01

    The cycle maximum temperature effect on the properties of individual apparatuses and total NPP energy blocks characteristics has been investigated. Air, nitrogen, helium and chemically reacting system N 2 O 4 +2NO+O 2 have been considered as coolants. The conducted investigations have shown that maximum temperature of thermodynamical cycle affects considerably both the weight-dimensional characteristics of individual elements of NPP and total characteristics of NPP energy block. Energy blocks of NPP with air cooling wherein dissociating nitrogen tetroxide is used as working body, have better indexes on the majority of characteristics in comparison with blocks with air, nitrogen and helium cooling. If technical restrictions are to be taken into account (thermal resistance of metals, coolant decomposition under high temperatures, etc.) then dissociating nitrogen tetroxide should be recommended as working body and maximum cycle temperature in the range from 500 up to 600 deg C

  4. Determination of trace concentration of uranium in soils by the nuclear track technique

    International Nuclear Information System (INIS)

    Islam, G.S.; Abdullah, M.N.A.

    1998-04-01

    Solid state nuclear track detector CR-39 has been used to estimate trace concentration of uranium in soil and sand samples from various places of Bangladesh. Uranium contents in soil samples have been found to vary from ∼3.79 to ∼8.63 ppm and in sand samples from ∼2.39 to ∼6.53 ppm. The mean concentration in soil and in sand samples were found to be ∼4.52 and ∼2.96 ppm respectively. The maximum uranium concentration in soil samples was observed in Sylhet while the uranium concentration of sand was found to be maximum in the sea beach of Cox's Bazar. The implication of results is briefly discussed in the paper. (author)

  5. A maximum power point tracking for photovoltaic-SPE system using a maximum current controller

    Energy Technology Data Exchange (ETDEWEB)

    Muhida, Riza [Osaka Univ., Dept. of Physical Science, Toyonaka, Osaka (Japan); Osaka Univ., Dept. of Electrical Engineering, Suita, Osaka (Japan); Park, Minwon; Dakkak, Mohammed; Matsuura, Kenji [Osaka Univ., Dept. of Electrical Engineering, Suita, Osaka (Japan); Tsuyoshi, Akira; Michira, Masakazu [Kobe City College of Technology, Nishi-ku, Kobe (Japan)

    2003-02-01

    Processes to produce hydrogen from solar photovoltaic (PV)-powered water electrolysis using solid polymer electrolysis (SPE) are reported. An alternative control of maximum power point tracking (MPPT) in the PV-SPE system based on the maximum current searching methods has been designed and implemented. Based on the characteristics of voltage-current and theoretical analysis of SPE, it can be shown that the tracking of the maximum current output of DC-DC converter in SPE side will track the MPPT of photovoltaic panel simultaneously. This method uses a proportional integrator controller to control the duty factor of DC-DC converter with pulse-width modulator (PWM). The MPPT performance and hydrogen production performance of this method have been evaluated and discussed based on the results of the experiment. (Author)

  6. Prescriptive amplification recommendations for hearing losses with a conductive component and their impact on the required maximum power output: an update with accompanying clinical explanation.

    Science.gov (United States)

    Johnson, Earl E

    2013-06-01

    Hearing aid prescriptive recommendations for hearing losses having a conductive component have received less clinical and research interest than for losses of a sensorineural nature; as a result, much variation remains among current prescriptive methods in their recommendations for conductive and mixed hearing losses (Johnson and Dillon, 2011). The primary intent of this brief clinical note is to demonstrate differences between two algebraically equivalent expressions of hearing loss, which have been approaches used historically to generate a prescription for hearing losses with a conductive component. When air and bone conduction thresholds are entered into hearing aid prescriptions designed for nonlinear hearing aids, it was hypothesized that that two expressions would not yield equivalent amounts of prescribed insertion gain and output. These differences are examined for their impact on the maximum power output (MPO) requirements of the hearing aid. Subsequently, the MPO capabilities of two common behind-the-ear (BTE) receiver placement alternatives, receiver-in-aid (RIA) and receiver-in-canal (RIC), are examined. The two expressions of hearing losses examined were the 25% ABG + AC approach and the 75% ABG + BC approach, where ABG refers to air-bone gap, AC refers to air-conduction threshold, and BC refers to bone-conduction threshold. Example hearing loss cases with a conductive component are sampled for calculations. The MPO capabilities of the BTE receiver placements in commercially-available products were obtained from hearing aids on the U.S. federal purchasing contract. Prescribed gain and the required MPO differs markedly between the two approaches. The 75% ABG + BC approach prescribes a compression ratio that is reflective of the amount of sensorineural hearing loss. Not all hearing aids will have the MPO capabilities to support the output requirements for fitting hearing losses with a large conductive component particularly when combined with

  7. Non-IID Recommender Systems: A Review and Framework of Recommendation Paradigm Shifting

    Directory of Open Access Journals (Sweden)

    Longbing Cao

    2016-06-01

    Full Text Available While recommendation plays an increasingly critical role in our living, study, work, and entertainment, the recommendations we receive are often for irrelevant, duplicate, or uninteresting products and services. A critical reason for such bad recommendations lies in the intrinsic assumption that recommended users and items are independent and identically distributed (IID in existing theories and systems. Another phenomenon is that, while tremendous efforts have been made to model specific aspects of users or items, the overall user and item characteristics and their non-IIDness have been overlooked. In this paper, the non-IID nature and characteristics of recommendation are discussed, followed by the non-IID theoretical framework in order to build a deep and comprehensive understanding of the intrinsic nature of recommendation problems, from the perspective of both couplings and heterogeneity. This non-IID recommendation research triggers the paradigm shift from IID to non-IID recommendation research and can hopefully deliver informed, relevant, personalized, and actionable recommendations. It creates exciting new directions and fundamental solutions to address various complexities including cold-start, sparse data-based, cross-domain, group-based, and shilling attack-related issues.

  8. Design of three-dimensional nonimaging concentrators with inhomogeneous media

    Science.gov (United States)

    Minano, J. C.

    1986-09-01

    A three-dimensional nonimaging concentrator is an optical system that transforms a given four-parametric manifold of rays reaching a surface (entry aperture) into another four-parametric manifold of rays reaching the receiver. A procedure of design of such concentrators is developed. In general, the concentrators use mirrors and inhomogeneous media (i.e., gradient-index media). The concentrator has the maximum concentration allowed by the theorem of conservation of phase-space volume. This is the first known concentrator with such properties. The Welford-Winston edge-ray principle in three-dimensional geometry is proven under several assumptions. The linear compound parabolic concentrator is derived as a particular case of the procedure of design.

  9. Experiences and recommendations in deploying a real-time, water quality monitoring system

    Science.gov (United States)

    O'Flynn, B.; Regan, F.; Lawlor, A.; Wallace, J.; Torres, J.; O'Mathuna, C.

    2010-12-01

    Monitoring of water quality at a river basin level to meet the requirements of the Water Framework Directive (WFD) using conventional sampling and laboratory-based techniques poses a significant financial burden. Wireless sensing systems offer the potential to reduce these costs considerably, as well as provide more useful, continuous monitoring capabilities by giving an accurate idea of the changing environmental and water quality in real time. It is unlikely that the traditional spot/grab sampling will provide a reasonable estimate of the true maximum and/or mean concentration for a particular physicochemical variable in a water body with marked temporal variability. When persistent fluctuations occur, it is likely only to be detected through continuous measurements, which have the capability of detecting sporadic peaks of concentration. Thus, in situ sensors capable of continuous sampling of parameters required under the WFD would therefore provide more up-to-date information, cut monitoring costs and provide better coverage representing long-term trends in fluctuations of pollutant concentrations. DEPLOY is a technology demonstration project, which began planning and station selection and design in August 2008 aiming to show how state-of-the-art technology could be implemented for cost-effective, continuous and real-time monitoring of a river catchment. The DEPLOY project is seen as an important building block in the realization of a wide area autonomous network of sensors capable of monitoring the spatial and temporal distribution of important water quality and environmental target parameters. The demonstration sites chosen are based in the River Lee, which flows through Ireland's second largest city, Cork, and were designed to include monitoring stations in five zones considered typical of significant river systems--these monitor water quality parameters such as pH, temperature, depth, conductivity, turbidity and dissolved oxygen. Over one million data points

  10. Experiences and recommendations in deploying a real-time, water quality monitoring system

    International Nuclear Information System (INIS)

    O'Flynn, B; O'Mathuna, C; Regan, F; Lawlor, A; Wallace, J; Torres, J

    2010-01-01

    Monitoring of water quality at a river basin level to meet the requirements of the Water Framework Directive (WFD) using conventional sampling and laboratory-based techniques poses a significant financial burden. Wireless sensing systems offer the potential to reduce these costs considerably, as well as provide more useful, continuous monitoring capabilities by giving an accurate idea of the changing environmental and water quality in real time. It is unlikely that the traditional spot/grab sampling will provide a reasonable estimate of the true maximum and/or mean concentration for a particular physicochemical variable in a water body with marked temporal variability. When persistent fluctuations occur, it is likely only to be detected through continuous measurements, which have the capability of detecting sporadic peaks of concentration. Thus, in situ sensors capable of continuous sampling of parameters required under the WFD would therefore provide more up-to-date information, cut monitoring costs and provide better coverage representing long-term trends in fluctuations of pollutant concentrations. DEPLOY is a technology demonstration project, which began planning and station selection and design in August 2008 aiming to show how state-of-the-art technology could be implemented for cost-effective, continuous and real-time monitoring of a river catchment. The DEPLOY project is seen as an important building block in the realization of a wide area autonomous network of sensors capable of monitoring the spatial and temporal distribution of important water quality and environmental target parameters. The demonstration sites chosen are based in the River Lee, which flows through Ireland's second largest city, Cork, and were designed to include monitoring stations in five zones considered typical of significant river systems-–these monitor water quality parameters such as pH, temperature, depth, conductivity, turbidity and dissolved oxygen. Over one million data

  11. Rate maximum calculation of Dpa in CNA-II pressure vessel

    International Nuclear Information System (INIS)

    Mascitti, J. A

    2012-01-01

    The maximum dpa rate was calculated for the reactor in the following state: fresh fuel, no Xenon, a Boron concentration of 15.3 ppm, critical state, its control rods in the criticality position, hot, at full power (2160 MW). It was determined that the maximum dpa rate under such conditions is 3.54(2)x10 12 s -1 and it is located in the positions corresponding to θ=210 o in the azimuthal direction, and z=20 cm and -60 cm respectively in the axial direction, considering the calculation mesh centered at half height of the fuel element (FE) active length. The dpa rate spectrum was determined as well as the contribution to it for 4 energy groups: a thermal group, two epithermal groups and a fast one. The maximum dpa rate considering the photo-neutrons production from (γ, n) reaction in the heavy water of coolant and moderator was 3.93(4)x10 12 s -1 that is 11% greater than the obtained without photo-neutrons. This verified significant difference between both cases, suggest that photo-neutrons in large heavy water reactors such as CNA-II should not be ignored. The maximum DPA rate in the first mm of the reactor pressure vessel was calculated too and it was obtained a value of 4.22(6)x10 12 s -1 . It should be added that the calculation was carried out with the reactor complete accurate model, with no approximations in spatial or energy variables. Each value has, between parentheses, a percentage relative error representing the statistical uncertainty due to the probabilistic Monte Carlo method used to estimate it. More representative values may be obtained with this method if equilibrium burn-up distribution is used (author)

  12. Simulation of concentration spikes in cascades

    International Nuclear Information System (INIS)

    Wood, H.G.

    2006-01-01

    Research has been conducted to investigate the maximum possible enrichment that might be temporarily achieved in a facility that is producing enriched uranium for fuel for nuclear power reactors. The purpose is to provide information to evaluate if uranium enrichment facilities are producing 235 U enriched within declared limits appropriate for power reactors or if the facilities are actually producing more highly enriched uranium. The correlation between feed rate and separation factor in a gas centrifuge cascade shows that as flow decreases, the separation factor increases, thereby, creating small amounts of higher enriched uranium than would be found under optimum design operating conditions. The research uses a number of cascade enrichment programs to model the phenomenon and determine the maximum enrichment possible during the time transient of a gas centrifuge cascade. During cascade start-up, the flow through the centrifuges begins at lower than centrifuge design stage flow rates. Steady-state cascade models have been used to study the maximum 235 U concentrations that would be predicted in the cascade. These calculations should produce an upper bound of product concentrations expected during the transient phase of start-up. Due to the fact that there are different ways in which to start a cascade, several methods are used to determine the maximum enrichment during the time transient. Model cascades were created for gas centrifuges with several product to .feed assay separation factors. With this information, the models were defined and the equilibrium programs were used to determine the maximum enrichment level during the time transient. The calculations predict in a cascade with separation factor 1.254 designed to produce enriched uranium for the purpose of supplying reactor fuel, it would not be unreasonable to see some 235 U in the range of 12-15%. Higher assays produced during the start-up period might lead inspectors to believe the cascade is being

  13. Lake Basin Fetch and Maximum Length/Width

    Data.gov (United States)

    Minnesota Department of Natural Resources — Linear features representing the Fetch, Maximum Length and Maximum Width of a lake basin. Fetch, maximum length and average width are calcuated from the lake polygon...

  14. Maximum permissible voltage of YBCO coated conductors

    Energy Technology Data Exchange (ETDEWEB)

    Wen, J.; Lin, B.; Sheng, J.; Xu, J.; Jin, Z. [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Hong, Z., E-mail: zhiyong.hong@sjtu.edu.cn [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Wang, D.; Zhou, H.; Shen, X.; Shen, C. [Qingpu Power Supply Company, State Grid Shanghai Municipal Electric Power Company, Shanghai (China)

    2014-06-15

    Highlights: • We examine three kinds of tapes’ maximum permissible voltage. • We examine the relationship between quenching duration and maximum permissible voltage. • Continuous I{sub c} degradations under repetitive quenching where tapes reaching maximum permissible voltage. • The relationship between maximum permissible voltage and resistance, temperature. - Abstract: Superconducting fault current limiter (SFCL) could reduce short circuit currents in electrical power system. One of the most important thing in developing SFCL is to find out the maximum permissible voltage of each limiting element. The maximum permissible voltage is defined as the maximum voltage per unit length at which the YBCO coated conductors (CC) do not suffer from critical current (I{sub c}) degradation or burnout. In this research, the time of quenching process is changed and voltage is raised until the I{sub c} degradation or burnout happens. YBCO coated conductors test in the experiment are from American superconductor (AMSC) and Shanghai Jiao Tong University (SJTU). Along with the quenching duration increasing, the maximum permissible voltage of CC decreases. When quenching duration is 100 ms, the maximum permissible of SJTU CC, 12 mm AMSC CC and 4 mm AMSC CC are 0.72 V/cm, 0.52 V/cm and 1.2 V/cm respectively. Based on the results of samples, the whole length of CCs used in the design of a SFCL can be determined.

  15. Reconstructing Historical VOC Concentrations in Drinking Water for Epidemiological Studies at a U.S. Military Base: Summary of Results

    Directory of Open Access Journals (Sweden)

    Morris L. Maslia

    2016-10-01

    Full Text Available A U.S. government health agency conducted epidemiological studies to evaluate whether exposures to drinking water contaminated with volatile organic compounds (VOC at U.S. Marine Corps Base Camp Lejeune, North Carolina, were associated with increased health risks to children and adults. These health studies required knowledge of contaminant concentrations in drinking water—at monthly intervals—delivered to family housing, barracks, and other facilities within the study area. Because concentration data were limited or unavailable during much of the period of contamination (1950s–1985, the historical reconstruction process was used to quantify estimates of monthly mean contaminant-specific concentrations. This paper integrates many efforts, reports, and papers into a synthesis of the overall approach to, and results from, a drinking-water historical reconstruction study. Results show that at the Tarawa Terrace water treatment plant (WTP reconstructed (simulated tetrachloroethylene (PCE concentrations reached a maximum monthly average value of 183 micrograms per liter (μg/L compared to a one-time maximum measured value of 215 μg/L and exceeded the U.S. Environmental Protection Agency’s current maximum contaminant level (MCL of 5 μg/L during the period November 1957–February 1987. At the Hadnot Point WTP, reconstructed trichloroethylene (TCE concentrations reached a maximum monthly average value of 783 μg/L compared to a one-time maximum measured value of 1400 μg/L during the period August 1953–December 1984. The Hadnot Point WTP also provided contaminated drinking water to the Holcomb Boulevard housing area continuously prior to June 1972, when the Holcomb Boulevard WTP came on line (maximum reconstructed TCE concentration of 32 μg/L and intermittently during the period June 1972–February 1985 (maximum reconstructed TCE concentration of 66 μg/L. Applying the historical reconstruction process to quantify contaminant

  16. Effect of Sugar Concentration in Jerusalem Artichoke Extract on Kluyveromyces marxianus Growth and Ethanol Production

    OpenAIRE

    Margaritis, Argyrios; Bajpai, Pratima

    1983-01-01

    The effect of inulin sugars concentration on the growth and ethanol production by Kluyveromyces marxianus UCD (FST) 55-82 was studied. A maximum ethanol concentration of 102 g/liter was obtained from 250 g of sugars per liter initial concentration. The maximum specific growth rate varied from 0.44 h−1 at 50 g of sugar per liter to 0.13 h−1 at 300 g of sugar per liter, whereas the ethanol yield remained almost constant at 0.45 g of ethanol per g of sugars utilized.

  17. Receiver function estimated by maximum entropy deconvolution

    Institute of Scientific and Technical Information of China (English)

    吴庆举; 田小波; 张乃铃; 李卫平; 曾融生

    2003-01-01

    Maximum entropy deconvolution is presented to estimate receiver function, with the maximum entropy as the rule to determine auto-correlation and cross-correlation functions. The Toeplitz equation and Levinson algorithm are used to calculate the iterative formula of error-predicting filter, and receiver function is then estimated. During extrapolation, reflective coefficient is always less than 1, which keeps maximum entropy deconvolution stable. The maximum entropy of the data outside window increases the resolution of receiver function. Both synthetic and real seismograms show that maximum entropy deconvolution is an effective method to measure receiver function in time-domain.

  18. Changes in power and force generation during coupled eccentric-concentric versus concentric muscle contraction with training and aging

    DEFF Research Database (Denmark)

    Caserotti, Paolo; Aagaard, Per; Puggaard, Lis

    2008-01-01

    Age-related decline in maximal concentric muscle power is associated with frailty and functional impairments in the elderly. Compared to concentric contraction, mechanical muscle output is generally enhanced when muscles are rapidly pre-stretched (eccentric contraction), albeit less pronounced...... with increasing age. Exercise has been recommended to prevent loss of muscle power and function and recent guidelines indicate training program for increasing muscle power highly relevant for elderly subjects. This study examined the differences in muscle power, force and movement pattern during concentric......) and JH increased in training group (P age-related decline in muscle power and functional performance observed in the control subjects, while substantial gains...

  19. Safety analysis of RA reactor operation, I-III, Part III - Environmental effect of the maximum credible accident

    International Nuclear Information System (INIS)

    Raisic, N.

    1963-02-01

    Maximum credible accident at the RA reactor would consider release of fission products into the environment. This would result from fuel elements failure or meltdown due to loss of coolant. The analysis presented in this report assumes that the reactor was operating at nominal power at the moment of maximum possible accident. The report includes calculations of fission products activity at the moment of accident, total activity release during the accident, concentration of radioactive material in the air in the reactor neighbourhood, and the analysis of accident environmental effects

  20. Context-aware recommender system based on ontology for recommending tourist destinations at Bandung

    Science.gov (United States)

    Rizaldy Hafid Arigi, L.; Abdurahman Baizal, Z. K.; Herdiani, Anisa

    2018-03-01

    Recommender System is software that is able to provide personalized recommendation suits users’ needs. Recommender System has been widely implemented in various domains, including tourism. One approach that can be done for more personalized recommendations is the use of contextual information. This paper proposes a context aware recommender based ontology system in the tourism domain. The system is capable of recommending tourist destinations by using user preferences of the categories of tourism and contextual information such as user locations, weather around tourist destinations and close time of destination. Based on the evaluation, the system has accuracy of of 0.94 (item recommendation precision evaluated by expert) and 0.58 (implicitly from system-end user interaction). Based on the evaluation of user satisfaction, the system provides a satisfaction level of more than 0.7 (scale 0 to 1) for speed factors for providing liked recommendations (PE), informative description of recommendations (INF) and user trust (TR).

  1. Implementation plan for the Defense Nuclear Facilities Safety Board Recommendation 90-7

    International Nuclear Information System (INIS)

    Borsheim, G.L.; Cash, R.J.; Dukelow, G.T.

    1992-12-01

    This document revises the original plan submitted in March 1991 for implementing the recommendations made by the Defense Nuclear Facilities Safety Board in their Recommendation 90-7 to the US Department of Energy. Recommendation 90-7 addresses safety issues of concern for 24 single-shell, high-level radioactive waste tanks containing ferrocyanide compounds at the Hanford Site. The waste in these tanks is a potential safety concern because, under certain conditions involving elevated temperatures and low concentrations of nonparticipating diluents, ferrocyanide compounds in the presence of oxidizing materials can undergo a runaway (propagating) chemical reaction. This document describes those activities underway by the Hanford Site contractor responsible for waste tank safety that address each of the six parts of Defense Nuclear Facilities Safety Board Recommendation 90-7. This document also identifies the progress made on these activities since the beginning of the ferrocyanide safety program in September 1990. Revised schedules for planned activities are also included

  2. Performance of penalized maximum likelihood in estimation of genetic covariances matrices

    Directory of Open Access Journals (Sweden)

    Meyer Karin

    2011-11-01

    Full Text Available Abstract Background Estimation of genetic covariance matrices for multivariate problems comprising more than a few traits is inherently problematic, since sampling variation increases dramatically with the number of traits. This paper investigates the efficacy of regularized estimation of covariance components in a maximum likelihood framework, imposing a penalty on the likelihood designed to reduce sampling variation. In particular, penalties that "borrow strength" from the phenotypic covariance matrix are considered. Methods An extensive simulation study was carried out to investigate the reduction in average 'loss', i.e. the deviation in estimated matrices from the population values, and the accompanying bias for a range of parameter values and sample sizes. A number of penalties are examined, penalizing either the canonical eigenvalues or the genetic covariance or correlation matrices. In addition, several strategies to determine the amount of penalization to be applied, i.e. to estimate the appropriate tuning factor, are explored. Results It is shown that substantial reductions in loss for estimates of genetic covariance can be achieved for small to moderate sample sizes. While no penalty performed best overall, penalizing the variance among the estimated canonical eigenvalues on the logarithmic scale or shrinking the genetic towards the phenotypic correlation matrix appeared most advantageous. Estimating the tuning factor using cross-validation resulted in a loss reduction 10 to 15% less than that obtained if population values were known. Applying a mild penalty, chosen so that the deviation in likelihood from the maximum was non-significant, performed as well if not better than cross-validation and can be recommended as a pragmatic strategy. Conclusions Penalized maximum likelihood estimation provides the means to 'make the most' of limited and precious data and facilitates more stable estimation for multi-dimensional analyses. It should

  3. Total lead concentration in new decorative enamel paints in Lebanon, Paraguay and Russia.

    Science.gov (United States)

    Clark, C Scott; Speranskaya, Olga; Brosche, Sara; Gonzalez, Hebe; Solis, Daniela; Kodeih, Naji; Roda, Sandy; Lind, Caroline

    2015-04-01

    Lead concentrations in new enamel decorative paints were determined in three countries in different areas of the world where data were not previously available. The average total lead concentration of the enamel decorative paints purchased in Lebanon, Paraguay and Russia was 24,500ppm (ppm, dry weight), more than 270 times the current limit of 90ppm in Canada and in the United States. Sixty-three percent of these paints contained concentrations greater than 90ppm. Fifty-nine percent contained concentrations greater than 600ppm, the current limit in some countries. The maximum concentrations found were 236,000ppm in Lebanon, 169,000ppm in Paraguay and 52,900ppm in Russia. An average of 29% of the samples contained exceedingly high lead concentrations, >=10,000ppm. Five brands of paint were sampled in each of Lebanon and Paraguay and seven in Russia. Three colors from each brand were analyzed. For five of the six samples of the two brands in Lebanon with affiliations outside the country, the lead concentrations ranged from 1360ppm to 135,000ppm. In Lebanon the maximum concentration in the Egypt-affiliated brand (Sipes) was 135,000ppm and the maximum for the USA-affiliated brand (Dutch Boy) was 32,400ppm. Lead was not detected in any paints from the three of the four brands of paint purchased in Paraguay that had headquarters/affiliations in other countries (Brazil-Coralit), Germany (Suvinil) and USA (Novacor)). Two of the three paints from each of the other Paraguay brands contained high levels of lead with the maximum concentrations of 108,000 and 168,000ppm; one of these brands was manufactured under a license from ICI in the Netherlands. All of the paints purchased in Russia were from Russian brands and were manufactured in Russia. All three paints from one brand contained below detection levels of lead. The maximum levels of lead in the other six brands in Russia ranged from 3230 to 52,900ppm. The two brands with the highest lead concentration, TEKS and LAKRA

  4. Maximum Gene-Support Tree

    Directory of Open Access Journals (Sweden)

    Yunfeng Shan

    2008-01-01

    Full Text Available Genomes and genes diversify during evolution; however, it is unclear to what extent genes still retain the relationship among species. Model species for molecular phylogenetic studies include yeasts and viruses whose genomes were sequenced as well as plants that have the fossil-supported true phylogenetic trees available. In this study, we generated single gene trees of seven yeast species as well as single gene trees of nine baculovirus species using all the orthologous genes among the species compared. Homologous genes among seven known plants were used for validation of the finding. Four algorithms—maximum parsimony (MP, minimum evolution (ME, maximum likelihood (ML, and neighbor-joining (NJ—were used. Trees were reconstructed before and after weighting the DNA and protein sequence lengths among genes. Rarely a gene can always generate the “true tree” by all the four algorithms. However, the most frequent gene tree, termed “maximum gene-support tree” (MGS tree, or WMGS tree for the weighted one, in yeasts, baculoviruses, or plants was consistently found to be the “true tree” among the species. The results provide insights into the overall degree of divergence of orthologous genes of the genomes analyzed and suggest the following: 1 The true tree relationship among the species studied is still maintained by the largest group of orthologous genes; 2 There are usually more orthologous genes with higher similarities between genetically closer species than between genetically more distant ones; and 3 The maximum gene-support tree reflects the phylogenetic relationship among species in comparison.

  5. Nonimaging achromatic shaped Fresnel lenses for ultrahigh solar concentration.

    Science.gov (United States)

    Languy, Fabian; Habraken, Serge

    2013-05-15

    The maximum concentration ratio achievable with a solar concentrator made of a single refractive primary optics is much more limited by the chromatic aberration than by any other aberration. Therefore achromatic doublets made with poly(methyl methacrylate) and polycarbonate are of great interest to enhance the concentration ratio and to achieve a spectrally uniform flux on the receiver. In this Letter, shaped achromatic Fresnel lenses are investigated. One lossless design is of high interest since it provides spectrally and spatially uniform flux without being affected by soiling problems. With this design an optical concentration ratio of about 8500× can be achieved.

  6. Toxicokinetics of fumonisin B1 in turkey poults and tissue persistence after exposure to a diet containing the maximum European tolerance for fumonisins in avian feeds.

    Science.gov (United States)

    Tardieu, Didier; Bailly, Jean-Denis; Skiba, Fabien; Grosjean, François; Guerre, Philippe

    2008-09-01

    The kinetic of fumonisin B1 (FB1) after a single IV and oral dose, and FB1 persistence in tissue were investigated in turkey poults by HPLC after purification of samples on columns. After IV administration (single-dose: 10mg FB1/kg bw), serum concentration-time curves were best described by a three-compartment open model. Elimination half-life and mean residence time of FB1 were 85 and 52min, respectively. After oral administration (single-dose: 100mg FB1/kg bw) bioavailability was 3.2%; elimination half-life and mean residence time were 214 and 408min, respectively. Clearance of FB1 was 7.6 and 7.5ml/min/kg for IV and oral administration, respectively. Twenty-four hours after the administration of FB1 by the intravenous route, liver and kidney contained the highest levels of FB1 in tissues, level in muscle was low or below the limit of detection (LD, 13microg/kg). The persistence of FB1 in tissue was also studied after administration for 9 weeks of a feed that contained 5, 10 and 20mg FB1+FB2/kg diet. Eight hours after the last intake of 20mg FB1+FB2/kg feed (maximum recommended concentration of fumonisins established by the EU for avian feed), hepatic and renal FB1 concentrations were 119 and 22microg/kg, level in muscles was below the LD.

  7. Silicon concentrator cells in a two-stage photovoltaic system with a concentration factor of 300x

    Energy Technology Data Exchange (ETDEWEB)

    Mohr, A.

    2005-06-15

    In this work a rear contacted silicon concentrator cell was developed for an application in a two stage concentrator photovoltaic system. This system was developed at Fraunhofer ISE some years ago. The innovation of this one-axis tracked system is that it enables a high geometrical concentration of 300x in combination with a high optical efficiency (around 78%) and a large acceptance angle of {+-}23.5 all year through. For this, the system uses a parabolic mirror (40.4x) and a three dimensional second stage consisting of compound parabolic concentrators (CPCs, 7.7x). For the concentrator concept and particularly for an easy cell integration, the rear line contacted concentrator (RLCC) cells with a maximum efficiency of 25% were developed and a hybrid mounting concept for the RLCC cells is presented. The optical performance of different CPC materials was tested and analysed in this work. Finally, small modules consisting of six series interconnected RLCC cells and six CPCs were integrated into the concentrator system and tested outdoor. A system efficiency of 16.2% was reached at around 800 W/m2 direct irradiance under realistic outdoor conditions. (orig.)

  8. Extracorporeal treatment for valproic acid poisoning: systematic review and recommendations from the EXTRIP workgroup.

    Science.gov (United States)

    Ghannoum, Marc; Laliberté, Martin; Nolin, Thomas D; MacTier, Robert; Lavergne, Valery; Hoffman, Robert S; Gosselin, Sophie

    2015-06-01

    The EXtracorporeal TReatments In Poisoning (EXTRIP) workgroup presents its systematic review and clinical recommendations on the use of extracorporeal treatment (ECTR) in valproic acid (VPA) poisoning. The lead authors reviewed all of the articles from a systematic literature search, extracted the data, summarized the key findings, and proposed structured voting statements following a predetermined format. A two-round modified Delphi method was chosen to reach a consensus on voting statements and the RAND/UCLA Appropriateness Method was used to quantify disagreement. Anonymous votes were compiled, returned, and discussed in person. A second vote was conducted to determine the final workgroup recommendations. The latest literature search conducted in November 2014 retrieved a total of 79 articles for final qualitative analysis, including one observational study, one uncontrolled cohort study with aggregate analysis, 70 case reports and case series, and 7 pharmacokinetic studies, yielding a very low quality of evidence for all recommendations. Clinical data were reported for 82 overdose patients while pharmaco/toxicokinetic grading was performed in 55 patients. The workgroup concluded that VPA is moderately dialyzable (level of evidence = B) and made the following recommendations: ECTR is recommended in severe VPA poisoning (1D); recommendations for ECTR include a VPA concentration > 1300 mg/L (9000 μmol/L)(1D), the presence of cerebral edema (1D) or shock (1D); suggestions for ECTR include a VPA concentration > 900 mg/L (6250 μmol/L)(2D), coma or respiratory depression requiring mechanical ventilation (2D), acute hyperammonemia (2D), or pH ≤ 7.10 (2D). Cessation of ECTR is indicated when clinical improvement is apparent (1D) or the serum VPA concentration is between 50 and 100 mg/L (350-700 μmol/L)(2D). Intermittent hemodialysis is the preferred ECTR in VPA poisoning (1D). If hemodialysis is not available, then intermittent hemoperfusion (1D) or continuous

  9. Determination of activity concentration levels of (238)U, (232)Th, and (40)K in drinking water in a gold mine in Ghana.

    Science.gov (United States)

    Awudu, A R; Darko, E O; Schandorf, C; Hayford, E K; Abekoe, M K; Ofori-Danson, P K

    2010-08-01

    The study of the activity concentration levels of uranium, thorium and potassium in drinking water from different locations in a gold mine in the Ashanti Region of Ghana was conducted using gamma spectrometry. The mean outdoor absorbed gamma dose rates at 1 m from the water were 0.524 nGy h, 0.422 nGy h, and 0.252 nGy h for groundwater, surface water, and treated water, respectively. The results obtained for the activity concentration levels of U and Th are found to be within the maximum acceptable concentration levels of 3.0 Bq L and 0.6 Bq L, respectively, recommended by the World Health Organization. The overall mean outdoor gamma dose rate is 0.41 nGy h and the corresponding outdoor annual effective dose obtained for adult members of the public for drinking water from the mines is 3.58 muSv y. This value is found to be within the 10.0 muSv per annum (0.01 mSv per annum) for public exposure control set by the World Health Organization. Therefore, the mining activities on drinking water studied did not show any significant radiological health implications on the public.

  10. Analysis of atmospheric concentrations of radon and thoron using beta counting technique

    International Nuclear Information System (INIS)

    Islam, G.S.; Basunia, S.M.

    1995-05-01

    This paper presents a detailed theory and experimental procedure for measurement and analysis of mixed radon and thoron in the environment. The technique has been successfully applied to the study of seasonal variations of radon and thoron in Rajshahi atmosphere during the years 1989-1991. The maximum radon concentration in outdoor air was observed in the winter from December to January while the indoor radon concentration was found to be maximum during the monsoon months of July and August. The implication of results is briefly discussed in the paper. (author). 4 refs, 6 figs, 2 tabs

  11. Thiosulphate leaching of gold-, silver-, copper flotation concentrates

    International Nuclear Information System (INIS)

    Samikhov, Sh.R.; Zinchenko, Z.A.

    2015-01-01

    Present article is devoted to thiosulphate leaching of gold-, silver-, copper flotation concentrates. For the purpose to improve the process of thiosulphate leaching the ore samples were calcined at temperature 600 ℃ during two hours. During the calcination process of gold-sulphide ores and concentrates the minerals pyrite and arsenopyrite oxidize which lead to opening of gold contains in them. It was defined that thiosulphate leaching can be recommended as an alternative to cyanic process.

  12. Recommendation in evolving online networks

    Science.gov (United States)

    Hu, Xiao; Zeng, An; Shang, Ming-Sheng

    2016-02-01

    Recommender system is an effective tool to find the most relevant information for online users. By analyzing the historical selection records of users, recommender system predicts the most likely future links in the user-item network and accordingly constructs a personalized recommendation list for each user. So far, the recommendation process is mostly investigated in static user-item networks. In this paper, we propose a model which allows us to examine the performance of the state-of-the-art recommendation algorithms in evolving networks. We find that the recommendation accuracy in general decreases with time if the evolution of the online network fully depends on the recommendation. Interestingly, some randomness in users' choice can significantly improve the long-term accuracy of the recommendation algorithm. When a hybrid recommendation algorithm is applied, we find that the optimal parameter gradually shifts towards the diversity-favoring recommendation algorithm, indicating that recommendation diversity is essential to keep a high long-term recommendation accuracy. Finally, we confirm our conclusions by studying the recommendation on networks with the real evolution data.

  13. Escherichia coli Concentrations in the Mill Creek Watershed, Cleveland, Ohio, 2001-2004

    Science.gov (United States)

    Brady, Amie M.G.

    2007-01-01

    Mill Creek in Cleveland, Ohio, receives discharges from combined-sewer overflows (CSOs) and other sanitary-sewage inputs. These discharges affect the water quality of the creek and that of its receiving stream, the Cuyahoga River. In an effort to mitigate this problem, the Northeast Ohio Regional Sewer District implemented a project to eliminate or control (by reducing the number of overflows) all of the CSOs in the Mill Creek watershed. This study focused on monitoring the microbiological water quality of the creek before and during sewage-collection system modifications. Routine samples were collected semimonthly from August 2001 through September 2004 at a site near a U.S. Geological Survey stream gage near the mouth of Mill Creek. In addition, event samples were collected September 19 and 22, 2003, when rainfall accumulations were 0.5 inches (in.) or greater. Concentrations of Escherichia coli (E. coli) were determined and instantaneous discharges were calculated. Streamflow and water-quality characteristics were measured at the time of sampling, and precipitation data measured at a nearby precipitation gage were obtained from the National Oceanic and Atmospheric Administration. Concentrations of E. coli were greater than Ohio's single-sample maximum for primary-contact recreation (298 colony-forming units per 100 milliliters (CFU/100 mL)) in 84 percent of the routine samples collected. In all but one routine sample E. coli concentrations in samples collected when instantaneous streamflows were greater than 20 cubic feet per second (ft3/s) were greater than Ohio's single-sample maximum. When precipitation occurred in the 24-hour period before routine sample collection, concentrations were greater than the maximum in 89 percent of the samples as compared to 73 percent when rainfall was absent during the 24 hours prior to routine sample collection. Before modifications to the sewage-collection system in the watershed began, E. coli concentrations in Mill Creek

  14. Dynamic Optimization of a Polymer Flooding Process Based on Implicit Discrete Maximum Principle

    Directory of Open Access Journals (Sweden)

    Yang Lei

    2012-01-01

    Full Text Available Polymer flooding is one of the most important technologies for enhanced oil recovery (EOR. In this paper, an optimal control model of distributed parameter systems (DPSs for polymer injection strategies is established, which involves the performance index as maximum of the profit, the governing equations as the fluid flow equations of polymer flooding, and some inequality constraints as polymer concentration and injection amount limitation. The optimal control model is discretized by full implicit finite-difference method. To cope with the discrete optimal control problem (OCP, the necessary conditions for optimality are obtained through application of the calculus of variations and Pontryagin’s discrete maximum principle. A modified gradient method with new adjoint construction is proposed for the computation of optimal injection strategies. The numerical results of an example illustrate the effectiveness of the proposed method.

  15. 75 FR 43840 - Inflation Adjustment of the Ordinary Maximum and Aggravated Maximum Civil Monetary Penalties for...

    Science.gov (United States)

    2010-07-27

    ...-17530; Notice No. 2] RIN 2130-ZA03 Inflation Adjustment of the Ordinary Maximum and Aggravated Maximum... remains at $250. These adjustments are required by the Federal Civil Penalties Inflation Adjustment Act [email protected] . SUPPLEMENTARY INFORMATION: The Federal Civil Penalties Inflation Adjustment Act of 1990...

  16. Half-width at half-maximum, full-width at half-maximum analysis

    Indian Academy of Sciences (India)

    addition to the well-defined parameter full-width at half-maximum (FWHM). The distribution of ... optical side-lobes in the diffraction pattern resulting in steep central maxima [6], reduc- tion of effects of ... and broad central peak. The idea of.

  17. Determinación de compuestos hidrocarbonados en la pared celular de P. maximum y L. leucocephala en silvopastoreo Determination of hydrocarbonated compounds in the cell wall from P. maximum and L. leucocephala under silvopastoral system conditions

    Directory of Open Access Journals (Sweden)

    Tania Sánchez

    2009-09-01

    Full Text Available Con el objetivo de determinar la concentración de n-alcanos y alcoholes de cadena larga en la pared celular de Panicum maximum cv. Likoni y Leucaena leucocephala cv. Cunningham, se realizó un estudio en una asociación de gramíneas mejoradas y leucaena de 10 años de establecida, la cual ocupa un área de 1,6 ha. Se seleccionaron dichas especies por ser las más representativas en la composición florística. Las muestras se colectaron de enero a diciembre del 2005 y se secaron. La concentración de n-alcanos de cadena impar fue de 167,97 y 222,96 mg/kg de MS y 134,11 y 137,27 mg/kg de MS para guinea y leucaena, en el período poco lluvioso y en el lluvioso, respectivamente. A su vez la concentración de alcoholes de cadena par para la leucaena presentó un valor mayor(2 754,60 y 3 830,18 mg/kg de MS para el período poco lluvioso y lluvioso, respectivamente, que en la guinea (2 571,73-3 679,65 mg/kg de MS para cada período, respectivamente. Se concluye que la concentración de n-alcanos de cadena larga impar fue baja para P. maximum y L. leucocephala en ambos períodos del año; sin embargo, presentaron concentraciones elevadas de alcoholes de cadena larga par, que pudieran ser utilizados como marcadores naturales en las dos especies.With the objective of determining the concentration of n-alkanes and long-chain alcohols in the cell wall of Panicum maximum cv. Likoni and Leucaena leucocephala cv. Cunningham, a study was conducted in an association of improved grasses and leucaena ten years after being established, which occupies an area of 1,6 ha. Such species were selected for being the most representative ones in the floristic composition. The samples were collected from January to December, 2005 and were dried. The concentration of odd-chain n-alkanes was 167,97 and 222,96 mg/kg DM and 134,11 and 137,27 mg/kg DM for Guinea grass and leucaena in the dry and rainy season, respectively. In turn, the concentration of even-chain alcohols for

  18. Application of Tryptophan Fluorescence Bandwidth-Maximum Plot in Analysis of Monoclonal Antibody Structure.

    Science.gov (United States)

    Huang, Cheng-Yen; Hsieh, Ming-Ching; Zhou, Qinwei

    2017-04-01

    Monoclonal antibodies have become the fastest growing protein therapeutics in recent years. The stability and heterogeneity pertaining to its physical and chemical structures remain a big challenge. Tryptophan fluorescence has been proven to be a versatile tool to monitor protein tertiary structure. By modeling the tryptophan fluorescence emission envelope with log-normal distribution curves, the quantitative measure can be exercised for the routine characterization of monoclonal antibody overall tertiary structure. Furthermore, the log-normal deconvolution results can be presented as a two-dimensional plot with tryptophan emission bandwidth vs. emission maximum to enhance the resolution when comparing samples or as a function of applied perturbations. We demonstrate this by studying four different monoclonal antibodies, which show the distinction on emission bandwidth-maximum plot despite their similarity in overall amino acid sequences and tertiary structures. This strategy is also used to demonstrate the tertiary structure comparability between different lots manufactured for one of the monoclonal antibodies (mAb2). In addition, in the unfolding transition studies of mAb2 as a function of guanidine hydrochloride concentration, the evolution of the tertiary structure can be clearly traced in the emission bandwidth-maximum plot.

  19. Two-dimensional maximum entropy image restoration

    International Nuclear Information System (INIS)

    Brolley, J.E.; Lazarus, R.B.; Suydam, B.R.; Trussell, H.J.

    1977-07-01

    An optical check problem was constructed to test P LOG P maximum entropy restoration of an extremely distorted image. Useful recovery of the original image was obtained. Comparison with maximum a posteriori restoration is made. 7 figures

  20. Maximum power point tracking

    International Nuclear Information System (INIS)

    Enslin, J.H.R.

    1990-01-01

    A well engineered renewable remote energy system, utilizing the principal of Maximum Power Point Tracking can be m ore cost effective, has a higher reliability and can improve the quality of life in remote areas. This paper reports that a high-efficient power electronic converter, for converting the output voltage of a solar panel, or wind generator, to the required DC battery bus voltage has been realized. The converter is controlled to track the maximum power point of the input source under varying input and output parameters. Maximum power point tracking for relative small systems is achieved by maximization of the output current in a battery charging regulator, using an optimized hill-climbing, inexpensive microprocessor based algorithm. Through practical field measurements it is shown that a minimum input source saving of 15% on 3-5 kWh/day systems can easily be achieved. A total cost saving of at least 10-15% on the capital cost of these systems are achievable for relative small rating Remote Area Power Supply systems. The advantages at larger temperature variations and larger power rated systems are much higher. Other advantages include optimal sizing and system monitor and control

  1. 7 CFR 3565.210 - Maximum interest rate.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Maximum interest rate. 3565.210 Section 3565.210... AGRICULTURE GUARANTEED RURAL RENTAL HOUSING PROGRAM Loan Requirements § 3565.210 Maximum interest rate. The interest rate for a guaranteed loan must not exceed the maximum allowable rate specified by the Agency in...

  2. AASC Recommendations for the Education of an Applied Climatologist

    Science.gov (United States)

    Nielsen-Gammon, J. W.; Stooksbury, D.; Akyuz, A.; Dupigny-Giroux, L.; Hubbard, K. G.; Timofeyeva, M. M.

    2011-12-01

    The American Association of State Climatologists (AASC) has developed curricular recommendations for the education of future applied and service climatologists. The AASC was founded in 1976. Membership of the AASC includes state climatologists and others who work in state climate offices; climate researchers in academia and educators; applied climatologists in NOAA and other federal agencies; and the private sector. The AASC is the only professional organization dedicated solely to the growth and development of applied and service climatology. The purpose of the recommendations is to offer a framework for existing and developing academic climatology programs. These recommendations are intended to serve as a road map and to help distinguish the educational needs for future applied climatologists from those of operational meteorologists or other scientists and practitioners. While the home department of climatology students may differ from one program to the next, the most essential factor is that students can demonstrate a breadth and depth of understanding in the knowledge and tools needed to be an applied climatologist. Because the training of an applied climatologist requires significant depth and breadth, the Masters degree is recommended as the minimum level of education needed. This presentation will highlight the AASC recommendations. These include a strong foundation in: - climatology (instrumentation and data collection, climate dynamics, physical climatology, synoptic and regional climatology, applied climatology, climate models, etc.) - basic natural sciences and mathematics including calculus, physics, chemistry, and biology/ecology - fundamental atmospheric sciences (atmospheric dynamics, atmospheric thermodynamics, atmospheric radiation, and weather analysis/synoptic meteorology) and - data analysis and spatial analysis (descriptive statistics, statistical methods, multivariate statistics, geostatistics, GIS, etc.). The recommendations also include a

  3. Maximum total organic carbon limits at different DWPF melter feed maters (U)

    International Nuclear Information System (INIS)

    Choi, A.S.

    1996-01-01

    The document presents information on the maximum total organic carbon (TOC) limits that are allowable in the DWPF melter feed without forming a potentially flammable vapor in the off-gas system were determined at feed rates varying from 0.7 to 1.5 GPM. At the maximum TOC levels predicted, the peak concentration of combustible gases in the quenched off-gas will not exceed 60 percent of the lower flammable limit during a 3X off-gas surge, provided that the indicated melter vapor space temperature and the total air supply to the melter are maintained. All the necessary calculations for this study were made using the 4-stage cold cap model and the melter off-gas dynamics model. A high-degree of conservatism was included in the calculational bases and assumptions. As a result, the proposed correlations are believed to by conservative enough to be used for the melter off-gas flammability control purposes

  4. Concentration and Health Implication of Heavy Metals in Drinking ...

    African Journals Online (AJOL)

    Concentration and Health Implication of Heavy Metals in Drinking Water from Urban ... water is not mentioned by WHO, but all the samples analyzed were found to ... Key words: Drinking water quality, Heavy metals, Maximum admissible limit, ...

  5. A comparative study on the effect of glazing and cooling for compound parabolic concentrator PV systems – Experimental and analytical investigations

    International Nuclear Information System (INIS)

    Bahaidarah, Haitham M.; Gandhidasan, P.; Baloch, Ahmer A.B.; Tanweer, Bilal; Mahmood, M.

    2016-01-01

    Highlights: • We model glazed and unglazed PV-CPC systems with and without active water cooling. • Model is validated with experimental results and found good agreement. • Significant increase in the maximum power output is observed with active cooling. • Unglazed PV-CPC system is recommended for greater electric power output. • Levelized cost of energy found was found lower for unglazed CPC with cooling. - Abstract: A key barrier to achieving the economic viability and widespread adoption of photovoltaic (PV) technology for the direct conversion of solar radiation to electricity is the losses related to the high operating temperatures of typical flat-type PV modules. This technical and economic study addresses the cost reduction of PV systems by proposing a methodology for the improvement of solar cell efficiency using low-concentration PV technology and compound parabolic concentrators (CPCs). A theoretical model was developed to evaluate the performance of PV-CPC systems considering their optical, thermal and electrical properties. The model was implemented to investigate glazed and unglazed PV-CPC systems with and without active cooling and it was validated against experimental data. A laboratory-scale bench-top PV string was designed and built with symmetrically truncated CPC modules in these four configurations. The constructed glazed and unglazed PV-CPC systems were used for measurements at the geographic location of Dhahran and showed a very good agreement of 3.8–6.5% between the calculated and experimental results. The effect of glazing was studied and from the electrical point of view, glazing was found to reduce the power output. From the thermal point of view, glazing increased the thermal gain of the PV-CPC system. An unglazed PV-CPC system is recommended for greater electric power output, and glazed system is recommended for higher thermal gain. For economic feasibility, levelized cost of energy (LCE) analysis was performed using annual

  6. Elemental concentration and chemical parameters of drinking water of Patiala City, India

    International Nuclear Information System (INIS)

    Sharma, H.K.; Singh, B.; Mittal, V.K.; Sahota, H.S.

    1989-01-01

    Neutron activation analysis and energy dispersive x-ray fluorescence techniques have been used to determine 28 major and trace element concentrations in drinking water. Conductivity, pH, hardness, alkalinity, chlorides and sulphates were also measured. The majority of the concentrations are well below the ISI/WHO recommended values. However cadmium, mercury, total dissolved solids (TDS) conductivity and alkalinity were found to be higher in about half the cases compared to ISI/WHO recommended values, whereas sodium was found to be higher in almost all the cases. A linear relationship was observed between TDS and conductivity. (author)

  7. Temperature and concentration transients in the aluminum-air battery

    Science.gov (United States)

    Homsy, R. V.

    1981-08-01

    Coupled conservation equations of heat and mass transfer are solved that predict temperature and concentration of the electrolyte of an aluminum-air battery system upon start-up and shutdown. Results of laboratory studies investigating the crystallization kinetics and solubility of the caustic-aluminate electrolyte system are used in the predictions. Temperature and concentration start-up transients are short, while during standby conditions, temperature increases to maximum and decreases slowly.

  8. Recommender systems

    OpenAIRE

    Lu L.; Medo M.; Yeung C.H.; Zhang Y.-C.; Zhang Z.-K.; Zhou T.

    2012-01-01

    The ongoing rapid expansion of the Internet greatly increases the necessity of effective recommender systems for filtering the abundant information. Extensive research for recommender systems is conducted by a broad range of communities including social and computer scientists, physicists, and interdisciplinary researchers. Despite substantial theoretical and practical achievements, unification and comparison of different approaches are lacking, which impedes further advances. In this article...

  9. Recommendations for natural bodybuilding contest preparation: resistance and cardiovascular training.

    Science.gov (United States)

    Helms, E R; Fitschen, P J; Aragon, A A; Cronin, J; Schoenfeld, B J

    2015-03-01

    The anabolic effect of resistance training can mitigate muscle loss during contest preparation. In reviewing relevant literature, we recommend a periodized approach be utilized. Block and undulating models show promise. Muscle groups should be trained 2 times weekly or more, although high volume training may benefit from higher frequencies to keep volume at any one session from becoming excessive. Low to high (~3-15) repetitions can be utilized but most repetitions should occur in the 6-12 range using 70-80% of 1 repetition maximum. Roughly 40-70 reps per muscle group per session should be performed, however higher volume may be appropriate for advanced bodybuilders. Traditional rest intervals of 1-3 minutes are adequate, but longer intervals can be used. Tempo should allow muscular control of the load; 1-2 s concentric and 2-3 s eccentric tempos. Training to failure should be limited when performing heavy loads on taxing exercises, and primarily relegated to single-joint exercises and higher repetitions. A core of multi-joint exercises with some single-joint exercises to address specific muscle groups as needed should be used, emphasizing full range of motion and proper form. Cardiovascular training can be used to enhance fat loss. Interference with strength training adaptations increases concomitantly with frequency and duration of cardiovascular training. Thus, the lowest frequency and duration possible while achieving sufficient fat loss should be used. Full-body modalities or cycling may reduce interference. High intensities may as well; however, require more recovery. Fasted cardiovascular training may not have benefits over fed-state and could be detrimental.

  10. Wetland methane emissions during the Last Glacial Maximum estimated from PMIP2 simulations: climate, vegetation and geographic controls

    NARCIS (Netherlands)

    Weber, S.L.; Drury, A.J.; Toonen, W.H.J.; Weele, M. van

    2010-01-01

    It is an open question to what extent wetlands contributed to the interglacial‐glacial decrease in atmospheric methane concentration. Here we estimate methane emissions from glacial wetlands, using newly available PMIP2 simulations of the Last Glacial Maximum (LGM) climate from coupled

  11. Applications of nonimaging optics for very high solar concentrations

    International Nuclear Information System (INIS)

    O'Gallagher, J.; Winston, R.

    1997-01-01

    Using the principles and techniques of nonimaging optics, solar concentrations that approach the theoretical maximum can be achieved. This has applications in solar energy collection wherever concentration is desired. In this paper, we survey recent progress in attaining and using high and ultrahigh solar fluxes. We review a number of potential applications for highly concentrated solar energy and the current status of the associated technology. By making possible new and unique applications for intense solar flux, these techniques have opened a whole new frontier for research and development of potentially economic uses of solar energy

  12. International Review Team (IRT) Safety Case Recommendations for the Yucca Mountain Total System Performance Assessment (TSPA) Supporting the Site Recommendation

    International Nuclear Information System (INIS)

    Van Luik, Abraham E.

    2004-01-01

    The session started with Abe Van Luik (IGSC Chair, US-DOE-YM, USA) who presented the feedback of the international peer review of the US-DOE Yucca Mountain TSPA (Total System Performance Assessment) supporting the successful designation of the site by the Congress and the President of the U.S. In particular, he listed key implications of the IRT (International Review team) recommendations on the forthcoming US-DOE documentation of its case for safety to be submitted to the regulator, the U.S. Nuclear Regulatory Commission, mainly: - The documentation submitted to the licensing authority should address technical aspects and compliance with regulatory criteria. - That documentation should reflect sound science and good engineering practice; it should present detailed and rigorous modelling. - In addition, it should present both quantitative and qualitative arguments, make a statement on why there can be confidence in the face of uncertainty, acknowledge remaining issues and provide the strategy to resolve them. - Demonstrating understanding is as important as demonstrating compliance. - There is a need to provide a clear explanation of the case made to the regulator for more general audiences to complement the large amount of technical documents that will be produced. The US-DOE response to these recommendations for the License Application, which is under preparation, is that the recommendations will be implemented to the maximum extent possible. In subsequent discussion, with respect to the License Application, it was acknowledged that detailed guidance from the U.S. regulator was very useful, and guidance of this type would be generally useful. At the current time, the words 'safety case' are not mentioned in U.S. regulations, but if one reads both the regulation and guidance documents it becomes evident that all aspects of a safety case need to be provided in the License Application and its accompanying documents

  13. Trust for intelligent recommendation

    CERN Document Server

    Bhuiyan, Touhid

    2013-01-01

    Recommender systems are one of the recent inventions to deal with the ever-growing information overload in relation to the selection of goods and services in a global economy. Collaborative Filtering (CF) is one of the most popular techniques in recommender systems. The CF recommends items to a target user based on the preferences of a set of similar users known as the neighbors, generated from a database made up of the preferences of past users. In the absence of these ratings, trust between the users could be used to choose the neighbor for recommendation making. Better recommendations can b

  14. Vitamin D in adolescents: Are current recommendations enough?

    Science.gov (United States)

    Smith, Taryn J; Lanham-New, Susan A; Hart, Kathryn H

    2017-10-01

    Vitamin D is essential for bone development during adolescence and low vitamin D status during this critical period of growth may impact bone mineralization, potentially reducing peak bone mass and consequently increasing the risk of osteoporosis in adulthood. Therefore, the high prevalence of vitamin D inadequacy and deficiency in adolescent populations is of great concern. However, there is currently a lack of consensus on the 25-hydroxyvitamin D [25(OH)D] concentration, the widely accepted biomarker of vitamin D status, that defines adequacy, and the vitamin D intake requirements to maintain various 25(OH)D thresholds are not well established. While the current intake recommendations of 10-15μg/day may be sufficient to prevent vitamin D deficiency (25(OH)D50nmol/l). This review will address these concerns and consider if the current dietary recommendations for vitamin D in adolescents are sufficient. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

  15. Further conventions for NMR shielding and chemical shifts (IUPAC Recommendations 2008)

    Energy Technology Data Exchange (ETDEWEB)

    Harris, R.K. [University of Durham, Durham (United Kingdom). Dept. of Chemistry; Becker, E.D. [National Institutes of Health, Bethesda, MD (United States); Menezes, S.M. Cabral de [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES); Granger, P. [University Louis Pasteur, Strasbourg (France). Inst. of Chemistry; Hoffman, R.E. [The Hebrew University of Jerusalem, Safra Campus, Jerusalem (Israel). Dept. of Organic Chemistry; Zilm, K.W., E-mail: r.k.harris@durham.ac.uk [Yale University, New Haven, CT (United States). Dept. of Chemistry

    2008-07-01

    IUPAC has published a number of recommendations regarding the reporting of nuclear magnetic resonance (NMR) data, especially chemical shifts. The most recent publication [Pure Appl. Chem. 73, 1795 (2001)] recommended that tetramethylsilane (TMS) serve as a universal reference for reporting the shifts of all nuclides, but it deferred recommendations for several aspects of this subject. This document first examines the extent to which the {sup 1}H shielding in TMS itself is subject to change by variation in temperature, concentration, and solvent. On the basis of recently published results, it has been established that the shielding of TMS in solution [along with that of sodium-3- (trimethylsilyl)propanesulfonate, DSS, often used as a reference for aqueous solutions] varies only slightly with temperature but is subject to solvent perturbations of a few tenths of a part per million (ppm). Recommendations are given for reporting chemical shifts under most routine experimental conditions and for quantifying effects of temperature and solvent variation, including the use of magnetic susceptibility corrections and of magic-angle spinning (MAS). This document provides the first IUPAC recommendations for referencing and reporting chemical shifts in solids, based on high-resolution MAS studies. Procedures are given for relating {sup 13}C NMR chemical shifts in solids to the scales used for high resolution studies in the liquid phase. The notation and terminology used for describing chemical shift and shielding tensors in solids are reviewed in some detail, and recommendations are given for best practice. (author)

  16. Further conventions for NMR shielding and chemical shifts (IUPAC Recommendations 2008)

    International Nuclear Information System (INIS)

    Harris, R.K.; Menezes, S.M. Cabral de; Granger, P.; Hoffman, R.E.; Zilm, K.W.

    2008-01-01

    IUPAC has published a number of recommendations regarding the reporting of nuclear magnetic resonance (NMR) data, especially chemical shifts. The most recent publication [Pure Appl. Chem. 73, 1795 (2001)] recommended that tetramethylsilane (TMS) serve as a universal reference for reporting the shifts of all nuclides, but it deferred recommendations for several aspects of this subject. This document first examines the extent to which the 1 H shielding in TMS itself is subject to change by variation in temperature, concentration, and solvent. On the basis of recently published results, it has been established that the shielding of TMS in solution [along with that of sodium-3- (trimethylsilyl)propanesulfonate, DSS, often used as a reference for aqueous solutions] varies only slightly with temperature but is subject to solvent perturbations of a few tenths of a part per million (ppm). Recommendations are given for reporting chemical shifts under most routine experimental conditions and for quantifying effects of temperature and solvent variation, including the use of magnetic susceptibility corrections and of magic-angle spinning (MAS). This document provides the first IUPAC recommendations for referencing and reporting chemical shifts in solids, based on high-resolution MAS studies. Procedures are given for relating 13 C NMR chemical shifts in solids to the scales used for high resolution studies in the liquid phase. The notation and terminology used for describing chemical shift and shielding tensors in solids are reviewed in some detail, and recommendations are given for best practice. (author)

  17. Item Anomaly Detection Based on Dynamic Partition for Time Series in Recommender Systems.

    Science.gov (United States)

    Gao, Min; Tian, Renli; Wen, Junhao; Xiong, Qingyu; Ling, Bin; Yang, Linda

    2015-01-01

    In recent years, recommender systems have become an effective method to process information overload. However, recommendation technology still suffers from many problems. One of the problems is shilling attacks-attackers inject spam user profiles to disturb the list of recommendation items. There are two characteristics of all types of shilling attacks: 1) Item abnormality: The rating of target items is always maximum or minimum; and 2) Attack promptness: It takes only a very short period time to inject attack profiles. Some papers have proposed item anomaly detection methods based on these two characteristics, but their detection rate, false alarm rate, and universality need to be further improved. To solve these problems, this paper proposes an item anomaly detection method based on dynamic partitioning for time series. This method first dynamically partitions item-rating time series based on important points. Then, we use chi square distribution (χ2) to detect abnormal intervals. The experimental results on MovieLens 100K and 1M indicate that this approach has a high detection rate and a low false alarm rate and is stable toward different attack models and filler sizes.

  18. Item Anomaly Detection Based on Dynamic Partition for Time Series in Recommender Systems

    Science.gov (United States)

    Gao, Min; Tian, Renli; Wen, Junhao; Xiong, Qingyu; Ling, Bin; Yang, Linda

    2015-01-01

    In recent years, recommender systems have become an effective method to process information overload. However, recommendation technology still suffers from many problems. One of the problems is shilling attacks-attackers inject spam user profiles to disturb the list of recommendation items. There are two characteristics of all types of shilling attacks: 1) Item abnormality: The rating of target items is always maximum or minimum; and 2) Attack promptness: It takes only a very short period time to inject attack profiles. Some papers have proposed item anomaly detection methods based on these two characteristics, but their detection rate, false alarm rate, and universality need to be further improved. To solve these problems, this paper proposes an item anomaly detection method based on dynamic partitioning for time series. This method first dynamically partitions item-rating time series based on important points. Then, we use chi square distribution (χ2) to detect abnormal intervals. The experimental results on MovieLens 100K and 1M indicate that this approach has a high detection rate and a low false alarm rate and is stable toward different attack models and filler sizes. PMID:26267477

  19. Linear stochastic models for forecasting daily maxima and hourly concentrations of air pollutants

    Energy Technology Data Exchange (ETDEWEB)

    McCollister, G M; Wilson, K R

    1975-04-01

    Two related time series models were developed to forecast concentrations of various air pollutants and tested on carbon monoxide and oxidant data for the Los Angeles basin. One model forecasts daily maximum concentrations of a particular pollutant using only past daily maximum values of that pollutant as input. The other model forecasts 1 hr average concentrations using only the past hourly average values. Both are significantly more accurate than persistence, i.e., forecasting for tomorrow what occurred today (or yesterday). Model forecasts for 1972 of the daily instantaneous maxima for total oxidant made using only past pollutant concentration data are more accurate than those made by the Los Angeles APCD using meteorological input as well as pollutant concentrations. Although none of these models forecast as accurately as might be desired for a health warning system, the relative success of simple time series models, even though based solely on pollutant concentration, suggests that models incorporating meteorological data and using either multi-dimensional times series or pattern recognition techniques should be tested.

  20. A Sentiment-Enhanced Hybrid Recommender System for Movie Recommendation: A Big Data Analytics Framework

    Directory of Open Access Journals (Sweden)

    Yibo Wang

    2018-01-01

    Full Text Available Movie recommendation in mobile environment is critically important for mobile users. It carries out comprehensive aggregation of user’s preferences, reviews, and emotions to help them find suitable movies conveniently. However, it requires both accuracy and timeliness. In this paper, a movie recommendation framework based on a hybrid recommendation model and sentiment analysis on Spark platform is proposed to improve the accuracy and timeliness of mobile movie recommender system. In the proposed approach, we first use a hybrid recommendation method to generate a preliminary recommendation list. Then sentiment analysis is employed to optimize the list. Finally, the hybrid recommender system with sentiment analysis is implemented on Spark platform. The hybrid recommendation model with sentiment analysis outperforms the traditional models in terms of various evaluation criteria. Our proposed method makes it convenient and fast for users to obtain useful movie suggestions.

  1. Xanthium strumarium L. pollen concentration in aeroplankton of Lublin in the years 2003-2005

    Directory of Open Access Journals (Sweden)

    Elżbieta Weryszko-Chmielewska

    2012-12-01

    Full Text Available Xanthium strumarium (common cocklebur pollen grains are included in allergenic types. During a three-year study (2003-2005 conducted by using the gravimetric method at two trap sites in Lublin, daily concentrations, maximum concentrations and annual sums of pollen grains, as well as the length of pollen seasons of this species were compared. The pollen season of common cocklebur starts in the first or second decade of July and lasts until the third decade of September. The length of the pollen season is 70-80 days. The highest cocklebur pollen concentrations, amounting to 40-59 z·cm-2, occurred between 8 and 18 August. The maximum cocklebur pollen concentrations differed slightly in particular trap sites over the period of three years of study. A statistically significant correlation between the Xanthium strumarium pollen concentration and average temperature was demonstrated only in one year of study (2004.

  2. Evaluation of the hydrometer for testing immunoglobulin G1 concentrations in Holstein colostrum.

    Science.gov (United States)

    Pritchett, L C; Gay, C C; Hancock, D D; Besser, T E

    1994-06-01

    Hydrometer measurement in globulin and IgG1 concentration measured by the radial immunodiffusion technique were compared for 915 samples of first milking colostrum from Holstein cows. Least squares analysis of the relationship between hydrometer measurement and IgG1 concentration was improved by log transformation of IgG1 concentration and resulted in a significant linear relationship between hydrometer measurement and log10 IgG1 concentration; r2 = .469. At 50 mg of globulin/ml of colostrum, the recommended hydrometer cutoff point for colostrum selection, the sensitivity of the hydrometer as a test of IgG1 concentration in Holstein colostrum was 26%, and the negative predictive value was 67%. The negative predictive value and sensitivity of the hydrometer as a test of IgG1 in Holstein colostrum was improved, and the cost of misclassification of colostrum was minimized, when the cutoff point for colostrum selection was increased above the recommended 50 mg/ml.

  3. Maximum permissible concentrations of uranium in air

    CERN Document Server

    Adams, N

    1973-01-01

    The retention of uranium by bone and kidney has been re-evaluated taking account of recently published data for a man who had been occupationally exposed to natural uranium aerosols and for adults who had ingested uranium at the normal dietary levels. For life-time occupational exposure to uranium aerosols the new retention functions yield a greater retention in bone and a smaller retention in kidney than the earlier ones, which were based on acute intakes of uranium by terminal patients. Hence bone replaces kidney as the critical organ. The (MPC) sub a for uranium 238 on radiological considerations using the current (1959) ICRP lung model for the new retention functions is slightly smaller than for earlier functions but the (MPC) sub a determined by chemical toxicity remains the most restrictive.

  4. Nickel, Aluminum and Strontium Concentration in Different Samples of Egyptian Foodstuff

    International Nuclear Information System (INIS)

    Abu Khadra, S.A.; Abd El-Fattah, A.T.; Anwar, S.M.

    2003-01-01

    Eight different types of food items, collected from eight Egyptian governorates, were subjected to elemental analysis to determine Ni, Al, and Sr concentration by using Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES). The result indicated that the concentration of Ni, Al and Sr are in range of 0.04-7.31, 0.07-5.56, 0.02-13.4 mg/kg-wet weight respectively. The maximum concentrations of Ni and Al are present in cereals and leafy vegetables while minimum values are present in roots and tubers. Sr concentration showed completely different trend. Its maximum value is present in fish samples. This focuses a very important remark about its active pathway (aquatic ecosystem) to prevent completely the disposal of radioactive Sr in any water body.By knowing the food consumption values by Egyptian, the daily dietary intake of these elements were calculated. The obtained mean values are 1.894, 2.242 and 1.483 mg/d/caput for Ni, Al and Sr respectively. These values are within the reported data and far away from their toxic intake level

  5. MXLKID: a maximum likelihood parameter identifier

    International Nuclear Information System (INIS)

    Gavel, D.T.

    1980-07-01

    MXLKID (MaXimum LiKelihood IDentifier) is a computer program designed to identify unknown parameters in a nonlinear dynamic system. Using noisy measurement data from the system, the maximum likelihood identifier computes a likelihood function (LF). Identification of system parameters is accomplished by maximizing the LF with respect to the parameters. The main body of this report briefly summarizes the maximum likelihood technique and gives instructions and examples for running the MXLKID program. MXLKID is implemented LRLTRAN on the CDC7600 computer at LLNL. A detailed mathematical description of the algorithm is given in the appendices. 24 figures, 6 tables

  6. Acetaminophen overdose associated with double serum concentration peaks

    Directory of Open Access Journals (Sweden)

    Cristian Papazoglu

    2015-12-01

    Full Text Available Acetaminophen is the most commonly used analgesic–antipyretic medication in the United States. Acetaminophen overdose, a frequent cause of drug toxicity, has been recognized as the leading cause of fatal and non-fatal hepatic necrosis. N-Acetylcysteine is the recommended antidote for acetaminophen poisoning. Despite evidence on the efficacy of N-acetylcysteine for prevention of hepatic injury, controversy persists about the optimal duration of the therapy. Here, we describe the case of a 65-year-old male with acetaminophen overdose and opioid co-ingestion who developed a second peak in acetaminophen serum levels after completing the recommended 21-hour intravenous N-acetylcysteine protocol and when the standard criteria for monitoring drug levels was achieved. Prolongation of N-acetylcysteine infusion beyond the standard protocol, despite a significant gap in treatment, was critical for successful avoidance of hepatotoxicity. Delay in acetaminophen absorption may be associated with a second peak in serum concentration following an initial declining trend, especially in cases of concomitant ingestion of opioids. In patients with acetaminophen toxicity who co-ingest other medications that may potentially delay gastric emptying or in those with risk factors for delayed absorption of acetaminophen, we recommend close monitoring of aminotransferase enzyme levels, as well as trending acetaminophen concentrations until undetectable before discontinuing the antidote therapy.

  7. Savannah River Site radioiodine atmospheric releases and offsite maximum doses

    International Nuclear Information System (INIS)

    Marter, W.L.

    1990-01-01

    Radioisotopes of iodine have been released to the atmosphere from the Savannah River Site since 1955. The releases, mostly from the 200-F and 200-H Chemical Separations areas, consist of the isotopes, I-129 and 1-131. Small amounts of 1-131 and 1-133 have also been released from reactor facilities and the Savannah River Laboratory. This reference memorandum was issued to summarize our current knowledge of releases of radioiodines and resultant maximum offsite doses. This memorandum supplements the reference memorandum by providing more detailed supporting technical information. Doses reported in this memorandum from consumption of the milk containing the highest I-131 concentration following the 1961 1-131 release incident are about 1% higher than reported in the reference memorandum. This is the result of using unrounded 1-131 concentrations of I-131 in milk in this memo. It is emphasized here that this technical report does not constitute a dose reconstruction in the same sense as the dose reconstruction effort currently underway at Hanford. This report uses existing published data for radioiodine releases and existing transport and dosimetry models

  8. NCBO Ontology Recommender 2.0: an enhanced approach for biomedical ontology recommendation.

    Science.gov (United States)

    Martínez-Romero, Marcos; Jonquet, Clement; O'Connor, Martin J; Graybeal, John; Pazos, Alejandro; Musen, Mark A

    2017-06-07

    Ontologies and controlled terminologies have become increasingly important in biomedical research. Researchers use ontologies to annotate their data with ontology terms, enabling better data integration and interoperability across disparate datasets. However, the number, variety and complexity of current biomedical ontologies make it cumbersome for researchers to determine which ones to reuse for their specific needs. To overcome this problem, in 2010 the National Center for Biomedical Ontology (NCBO) released the Ontology Recommender, which is a service that receives a biomedical text corpus or a list of keywords and suggests ontologies appropriate for referencing the indicated terms. We developed a new version of the NCBO Ontology Recommender. Called Ontology Recommender 2.0, it uses a novel recommendation approach that evaluates the relevance of an ontology to biomedical text data according to four different criteria: (1) the extent to which the ontology covers the input data; (2) the acceptance of the ontology in the biomedical community; (3) the level of detail of the ontology classes that cover the input data; and (4) the specialization of the ontology to the domain of the input data. Our evaluation shows that the enhanced recommender provides higher quality suggestions than the original approach, providing better coverage of the input data, more detailed information about their concepts, increased specialization for the domain of the input data, and greater acceptance and use in the community. In addition, it provides users with more explanatory information, along with suggestions of not only individual ontologies but also groups of ontologies to use together. It also can be customized to fit the needs of different ontology recommendation scenarios. Ontology Recommender 2.0 suggests relevant ontologies for annotating biomedical text data. It combines the strengths of its predecessor with a range of adjustments and new features that improve its reliability

  9. Assessment of concentrations of trace and toxic heavy metals in soil and vegetables grown in the vicinity of Manyoni uranium deposit in Tanzania

    International Nuclear Information System (INIS)

    Kapile, F.A.; Makundi, I.N.

    2016-01-01

    This study reports on determination of concentrations of trace and toxic heavy metals in soil and vegetables grown near of Manyoni uranium deposit. Soil and vegetable samples were collected from five sites namely Mitoo Mbuga, farming area, Miyomboni, Tambukareli and near water pump. The concentrations of heavy metals in soil and edible vegetables samples were analyzed using Energy Dispersive X-ray Fluorescence Spectrometry (EDXRF).All vegetable samples were found to have higher concentrations (in μg/g) of trace elements such as Ni (67.3) in pea leaves, Cu (14.9) in pumpkin leaves, Fe (478.6), (200.5) and (337.1) in pea, pumpkin and spinach leaves respectively, than the maximum tolerable limits recommended by WHO/FAO. Mean concentration of Pb (1.6 μg/g) in pumpkin leaves collected from Miyomboni (area D) were observed to be higher than the safe limit of (0.3μg/g) set by Codex 2006. Toxic elements concentrations (in μg/g) such as Cd (10.4), Pb (23.2),Hg (4.1), Th (31.5) and U (23.9) were observed to be high in soil collected from Mitoo Mbuga and farming area. Therefore, vegetables in the vicinity of Manyoni uranium deposit can expose people to toxic elements which are detrimental to their health.A more detailed study involving other foodstuffs is needed to establish conclusive results.

  10. Performance characteristics and parametric choices of a solar thermophotovoltaic cell at the maximum efficiency

    International Nuclear Information System (INIS)

    Dong, Qingchun; Liao, Tianjun; Yang, Zhimin; Chen, Xiaohang; Chen, Jincan

    2017-01-01

    Graphical abstract: The overall model of the solar thermophotovoltaic cell (STPVC) composed of an optical lens, an absorber, an emitter, and a photovoltaic (PV) cell with an integrated back-side reflector is updated to include various irreversible losses. - Highlights: • A new model of the irreversible solar thermophotovoltaic system is proposed. • The material and structure parameters of the system are considered. • The performance characteristics at the maximum efficiency are revealed. • The optimal values of key parameters are determined. • The system can obtain a large efficiency under a relative low concentration ratio. - Abstract: The overall model of the solar thermophotovoltaic cell (STPVC) composed of an optical lens, an absorber, an emitter, and a photovoltaic (PV) cell with an integrated back-side reflector is updated to include various irreversible losses. The power output and efficiency of the cell are analytically derived. The performance characteristics of the STPVC at the maximum efficiency are revealed. The optimum values of several important parameters, such as the voltage output of the PV cell, the area ratio of the absorber to the emitter, and the band-gap of the semiconductor material, are determined. It is found that under the condition of a relative low concentration ratio, the optimally designed STPVC can obtain a relative large efficiency.

  11. Maximum Expected Wall Heat Flux and Maximum Pressure After Sudden Loss of Vacuum Insulation on the Stratospheric Observatory for Infrared Astronomy (SOFIA) Liquid Helium (LHe) Dewars

    Science.gov (United States)

    Ungar, Eugene K.

    2014-01-01

    The aircraft-based Stratospheric Observatory for Infrared Astronomy (SOFIA) is a platform for multiple infrared observation experiments. The experiments carry sensors cooled to liquid helium (LHe) temperatures. A question arose regarding the heat input and peak pressure that would result from a sudden loss of the dewar vacuum insulation. Owing to concerns about the adequacy of dewar pressure relief in the event of a sudden loss of the dewar vacuum insulation, the SOFIA Program engaged the NASA Engineering and Safety Center (NESC). This report summarizes and assesses the experiments that have been performed to measure the heat flux into LHe dewars following a sudden vacuum insulation failure, describes the physical limits of heat input to the dewar, and provides an NESC recommendation for the wall heat flux that should be used to assess the sudden loss of vacuum insulation case. This report also assesses the methodology used by the SOFIA Program to predict the maximum pressure that would occur following a loss of vacuum event.

  12. Analysis of thiamine concentrations in commercial canned foods formulated for cats.

    Science.gov (United States)

    Markovich, Jessica E; Freeman, Lisa M; Heinze, Cailin R

    2014-01-15

    To measure thiamine concentrations in commercial canned foods formulated for cats as an initial assessment of the variation among canned foods and to determine the effects of flavor (fish vs nonfish) of the food, texture (paté vs nonpaté) of the food, country of manufacture, and size of the company on thiamine concentration. Prospective cross-sectional study. 90 canned, nontherapeutic diets formulated for cats (1 fish and 1 nonfish flavor for each of 45 brands). Each canned food was homogenized, and thiamine concentration was analyzed with a fluorometric method. Thiamine concentration was below the minimums of the Association of American Feed Control Officials in 12 of 90 (13.3%) foods and below the recommended allowance of the National Research Council in 14 of 90 (15.6%) foods. Paté foods had significantly lower thiamine concentrations than did nonpaté foods, and foods from smaller companies had significantly lower thiamine concentrations, compared with concentrations in foods from larger companies. Flavor of food and country of manufacture were not significantly associated with thiamine concentration. A wide range of thiamine concentrations was found in the foods evaluated. Thiamine concentration in a substantial percentage of commercially available canned foods was below the amount recommended for adult cats. Additional research on interlot and intralot variation in thiamine concentrations of foods formulated for cats is warranted. Companies should implement strict quality control and analysis practices regarding food products. Clinicians should consider thiamine deficiency as a differential diagnosis in a cat with acute neurologic dysfunction.

  13. GROWTH AND PRODUCTION OF ZUCCHINI IN FUNCTION OF COW URINE CONCENTRATION AND FORM OF APPLICATION

    Directory of Open Access Journals (Sweden)

    Nelson Licínio Campos de Oliveira2

    2013-12-01

    with maximum values estimated of 653, 784 and 9.80 g/plant, respectively; total number of fruit and number and fresh matter of commercial fruit had a quadratic behavior, with estimated maximum values of 10.0 and 9.5 fruit and of 1.72 kg, respectively, obtained at the concentration of 5%. When the solution was applied via soil, a greater production of total fresh mass of fruit/plant was obtained at the concentration of 2.55%; however, the best results in terms of fresh matter of commercial fruit and number of total and commercial fruit/plant was observed with foliar application of solution at a concentration of 5%.

  14. Extracorporeal treatment for carbamazepine poisoning: Systematic review and recommendations from the EXTRIP workgroup

    Science.gov (United States)

    Ghannoum, Marc; Yates, Christopher; Galvao, Tais F.; Sowinski, Kevin M.; Vo, Thi Hai Vân; Coogan, Andrew; Gosselin, Sophie; Lavergne, Valery; Nolin, Thomas D.; Hoffman, Robert S.

    2014-01-01

    Abstract Context. The Extracorporeal Treatments in Poisoning (EXTRIP) workgroup was created to provide evidence and consensus-based recommendations on the use of extracorporeal treatments (ECTRs) in poisoning. Objectives. To perform a systematic review and provide clinical recommendations for ECTR in carbamazepine poisoning. Methods. After a systematic literature search, the subgroup extracted the data and summarized the findings following a pre-determined format. The entire workgroup voted via a two-round modified Delphi method to reach a consensus on voting statements, using a RAND/UCLA Appropriateness Method to quantify disagreement. Anonymous votes were compiled, returned, and discussed in person. A second vote determined the final recommendations. Results. Seventy-four articles met inclusion criteria. Articles included case reports, case series, descriptive cohorts, pharmacokinetic studies, and in-vitro studies; two poor-quality observational studies were identified, yielding a very low quality of evidence for all recommendations. Data on 173 patients, including 6 fatalities, were reviewed. The workgroup concluded that carbamazepine is moderately dialyzable and made the following recommendations: ECTR is suggested in severe carbamazepine poisoning (2D). ECTR is recommended if multiple seizures occur and are refractory to treatment (1D), or if life-threatening dysrhythmias occur (1D). ECTR is suggested if prolonged coma or respiratory depression requiring mechanical ventilation are present (2D) or if significant toxicity persists, particularly when carbamazepine concentrations rise or remain elevated, despite using multiple-dose activated charcoal (MDAC) and supportive measures (2D). ECTR should be continued until clinical improvement is apparent (1D) or the serum carbamazepine concentration is below 10 mg/L (42 the μ in μmol/L looks weird.) (2D). Intermittent hemodialysis is the preferred ECTR (1D), but both intermittent hemoperfusion (1D) or continuous

  15. Linear and regressive stochastic models for prediction of daily maximum ozone values at Mexico City atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Bravo, J. L [Instituto de Geofisica, UNAM, Mexico, D.F. (Mexico); Nava, M. M [Instituto Mexicano del Petroleo, Mexico, D.F. (Mexico); Gay, C [Centro de Ciencias de la Atmosfera, UNAM, Mexico, D.F. (Mexico)

    2001-07-01

    We developed a procedure to forecast, with 2 or 3 hours, the daily maximum of surface ozone concentrations. It involves the adjustment of Autoregressive Integrated and Moving Average (ARIMA) models to daily ozone maximum concentrations at 10 monitoring atmospheric stations in Mexico City during one-year period. A one-day forecast is made and it is adjusted with the meteorological and solar radiation information acquired during the first 3 hours before the occurrence of the maximum value. The relative importance for forecasting of the history of the process and of meteorological conditions is evaluated. Finally an estimate of the daily probability of exceeding a given ozone level is made. [Spanish] Se aplica un procedimiento basado en la metodologia conocida como ARIMA, para predecir, con 2 o 3 horas de anticipacion, el valor maximo de la concentracion diaria de ozono. Esta basado en el calculo de autorregresiones y promedios moviles aplicados a los valores maximos de ozono superficial provenientes de 10 estaciones de monitoreo atmosferico en la Ciudad de Mexico y obtenidos durante un ano de muestreo. El pronostico para un dia se ajusta con la informacion meteorologica y de radiacion solar correspondiente a un periodo que antecede con al menos tres horas la ocurrencia esperada del valor maximo. Se compara la importancia relativa de la historia del proceso y de las condiciones meteorologicas previas para el pronostico. Finalmente se estima la probabilidad diaria de que un nivel normativo o preestablecido para contingencias de ozono sea rebasado.

  16. PWR Core II blanket fuel disposition recommendation of storage option study

    International Nuclear Information System (INIS)

    Dana, C.M.

    1995-01-01

    After review of the options available for current storage of T Plant Fuel the recommended option is wet storage without the use of chillers. A test has been completed that verifies the maximum temperature reached is below the industrial standard for storage of spent fuel. This option will be the least costly and still maintain the fuel in a safe environment. The options that were evaluated included dry storage with and without chillers, and wet storage with and without chillers. Due to the low decay heat of the Shippingport Core II Blanket fuel assemblies the fuel pool temperature will not exceed 100 deg. F

  17. Optical losses due to tracking error estimation for a low concentrating solar collector

    International Nuclear Information System (INIS)

    Sallaberry, Fabienne; García de Jalón, Alberto; Torres, José-Luis; Pujol-Nadal, Ramón

    2015-01-01

    Highlights: • A solar thermal collector with low concentration and one-axis tracking was tested. • A quasi-dynamic testing procedure for IAM was defined for tracking collector. • The adequation between the concentrator optics and the tracking was checked. • The maximum and long-term optical losses due to tracking error were calculated. - Abstract: The determination of the accuracy of a solar tracker used in domestic hot water solar collectors is not yet standardized. However, while using optical concentration devices, it is important to use a solar tracker with adequate precision with regard to the specific optical concentration factor. Otherwise, the concentrator would sustain high optical losses due to the inadequate focusing of the solar radiation onto its receiver, despite having a good quality. This study is focused on the estimation of long-term optical losses due to the tracking error of a low-temperature collector using low-concentration optics. For this purpose, a testing procedure for the incidence angle modifier on the tracking plane is proposed to determinate the acceptance angle of its concentrator even with different longitudinal incidence angles along the focal line plane. Then, the impact of maximum tracking error angle upon the optical efficiency has been determined. Finally, the calculation of the long-term optical error due to the tracking errors, using the design angular tracking error declared by the manufacturer, is carried out. The maximum tracking error calculated for this collector imply an optical loss of about 8.5%, which is high, but the average long-term optical loss calculated for one year was about 1%, which is reasonable for such collectors used for domestic hot water

  18. Preliminary study of radioactive concentration in treated sewage water

    Energy Technology Data Exchange (ETDEWEB)

    Elassaly, F M; Beal, A D.R. [Ministry of Health P.O. Box 1853 Dubai, (United Arab Emirates)

    1995-10-01

    Water from sewage treatment plant is used after processing for irrigation. Two water samples and one consolidated sludge (waste treatment products) were taken each day for period of months. Medical applications and research are the main sources of radioactivity such as Cr-51, Co-57, Ga-67, Se-75, Tc-99 m, In-111, Au-198 and Tl-201. Measurements were carried out using Hp Ge spectrometer with one liter Marinelli breaker. The maximum detected activity was 5.7 Bq.liter with a daily average of 2.4 Bq/liter for water. In the second period maximum activity was found to be 5 Bq/liter with an average daily activity 1.8 Bq/liter. The maximum activity recorded in the sludge during this period was 352 Bq/liter of which 343 Bq/liter was from I-131. The average daily activity was 162 Bq/liter. From these studies the levels of radioactivity concentration were 5 Bq/liter with an average 2 Bq/1 compared level 10 Bq/1 set for drinking water for Gcc countries. Although the sludge show higher activity of 353 Bq/liter it is kept for about year before being disposed. The maximum level for animal fodder is 300 Bq/kg for Gcc countries. These results indicate that radioactive concentration (2 Bq/liter) in the treated waste water present hazard to the public and environment. 6 figs., 4 tabs.

  19. Existing ingestion guidance: Problems and recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Mooney, Robert R; Ziegler, Gordon L; Peterson, Donald S [Environmental Radiation Section, Division of Radiation Protection, WA (United States)

    1989-09-01

    Washington State has been developing plans and procedures for responding to nuclear accidents since the early 1970s. A key part of this process has been formulating a method for calculating ingestion pathway concentration guides (CGs). Such a method must be both technically sound and easy to use. This process has been slow and frustrating. However, much technical headway has been made in recent years, and hopefully the experience of the State of Washington will provide useful insight to problems with the existing guidance. Several recommendations are offered on ways to deal with these problems. In January 1986, the state held an ingestion pathway exercise which required the determination of allowed concentrations of isotopes for various foods, based upon reactor source term and field data. Objectives of the exercise were not met because of the complexity of the necessary calculations. A major problem was that the allowed concentrations had to be computed for each isotope and each food group, given assumptions on the average diet. To solve problems identified during that exercise, Washington developed, by March 1986, partitioned CGs. These CGs apportioned doses from each food group for an assumed mix of radionuclides expected to result from a reactor accident. This effort was therefore in place just in time for actual use during the Chernobyl fallout episode in May 1986. This technique was refined and described in a later report and presented at the 1987 annual meeting of the Health Physics Society. Realizing the technical weaknesses which still existed and a need to simplify the numbers for decision makers, Washington State has been developing computer methods to quickly calculate, from an accident specific relative mix of isotopes, CGs which allow a single radionuclide concentration for all food groups. This latest approach allows constant CGs for different periods of time following the accident, instead of peak CGs, which are good only for a short time after the

  20. Existing ingestion guidance: Problems and recommendations

    International Nuclear Information System (INIS)

    Mooney, Robert R.; Ziegler, Gordon L.; Peterson, Donald S.

    1989-01-01

    Washington State has been developing plans and procedures for responding to nuclear accidents since the early 1970s. A key part of this process has been formulating a method for calculating ingestion pathway concentration guides (CGs). Such a method must be both technically sound and easy to use. This process has been slow and frustrating. However, much technical headway has been made in recent years, and hopefully the experience of the State of Washington will provide useful insight to problems with the existing guidance. Several recommendations are offered on ways to deal with these problems. In January 1986, the state held an ingestion pathway exercise which required the determination of allowed concentrations of isotopes for various foods, based upon reactor source term and field data. Objectives of the exercise were not met because of the complexity of the necessary calculations. A major problem was that the allowed concentrations had to be computed for each isotope and each food group, given assumptions on the average diet. To solve problems identified during that exercise, Washington developed, by March 1986, partitioned CGs. These CGs apportioned doses from each food group for an assumed mix of radionuclides expected to result from a reactor accident. This effort was therefore in place just in time for actual use during the Chernobyl fallout episode in May 1986. This technique was refined and described in a later report and presented at the 1987 annual meeting of the Health Physics Society. Realizing the technical weaknesses which still existed and a need to simplify the numbers for decision makers, Washington State has been developing computer methods to quickly calculate, from an accident specific relative mix of isotopes, CGs which allow a single radionuclide concentration for all food groups. This latest approach allows constant CGs for different periods of time following the accident, instead of peak CGs, which are good only for a short time after the

  1. Recommender systems and the social web leveraging tagging data for recommender systems

    CERN Document Server

    Gedikli, Fatih

    2013-01-01

    There is an increasing demand for recommender systems due to the information overload users are facing on the Web. The goal of a recommender system is to provide personalized recommendations of products or services to users. With the advent of the Social Web, user-generated content has enriched the social dimension of the Web. As user-provided content data also tells us something about the user, one can learn the user's individual preferences from the Social Web. This opens up completely new opportunities and challenges for recommender systems research. Fatih Gedikli deals with the question of

  2. Verbal and numerical consumer recommendations: switching between recommendation formats leads to preference inconsistencies.

    Science.gov (United States)

    Maciejovsky, Boris; Budescu, David V

    2013-06-01

    Many Web sites provide consumers with product recommendations, which are typically presented by a sequence of verbal reviews and numerical ratings. In three experiments, we demonstrate that when participants switch between formats (e.g., from verbal to numerical), they are more prone to preference inconsistencies than when they aggregate the recommendations within the same format (e.g., verbal). When evaluating recommendations, participants rely primarily on central-location measures (e.g., mean) and less on other distribution characteristics (e.g., variance). We explain our findings within the theoretical framework of stimulus-response compatibility and we make practical recommendations for the design of recommendation systems and Web portals.

  3. Optimal control of algae growth by controlling CO 2 and nutrition flow using Pontryagin Maximum Principle

    Science.gov (United States)

    Mardlijah; Jamil, Ahmad; Hanafi, Lukman; Sanjaya, Suharmadi

    2017-09-01

    There are so many benefit of algae. One of them is using for renewable energy and sustainable in the future. The greater growth of algae will increasing biodiesel production and the increase of algae growth is influenced by glucose, nutrients and photosynthesis process. In this paper, the optimal control problem of the growth of algae is discussed. The objective function is to maximize the concentration of dry algae while the control is the flow of carbon dioxide and the nutrition. The solution is obtained by applying the Pontryagin Maximum Principle. and the result show that the concentration of algae increased more than 15 %.

  4. Risk of Soil Recontamination Due to Using Eleusine coracana and Panicum maximum Straw After Phytoremediation of Picloram.

    Science.gov (United States)

    Nascimento, Alex Favaro; Pires, Fábio Ribeiro; Chagas, Kristhiano; de Oliveira Procópio, Sergio; Oliveira, Marcelo Antonio; Cargnelutti Filho, Alberto; Belo, Alessandra Ferreira; Egreja Filho, Fernando Barboza

    2015-01-01

    This study aimed to evaluate the herbicidal activity of picloram on the biomass of the remediation plants Eleusine coracana and Panicum maximum after cultivation in a soil contaminated with this herbicide. These species were grown in three soils, differentiated based on texture (clayish, middle, and sandy, with 460, 250, and 40 g kg(-1) of the clay, respectively), previously contaminated with picloram (0, 80, and 160 g ha(-1)). After 90 days, the plants were harvested and an extract was produced by maceration of leaves and stems of these plants. It was applied to pots containing washed sand, comprising a bioassay in a growth chamber using soybean as a bioindicator for picloram. Soil and plant samples were analyzed by HPLC. The results showed the presence of picloram or metabolites with herbicidal activity in the shoots of E. coracana and P. maximum at phytotoxic levels with regard to soybean plants, indicating that they work only as phytoextractors and that the presence of straw on the soil surface can promote recontamination within the area. It is not recommended to cultivate species susceptible to picloram in areas where it was reported remediation by E. indica and P. maximum and still present residues of these species.

  5. Recommender systems in knowledge-mining

    Science.gov (United States)

    Volna, Eva

    2017-07-01

    The subject of the paper is to analyse the possibilities of application of recommender systems in the field of data mining. The work focuses on three basic types of recommender systems (collaborative, content-based and hybrid). The goal of the article is to evaluate which of these three concepts of recommender systems provides forecast with the lowest error rate in the domain of recommending movies. This target is fulfilled by the practical part of the work - at first, the own recommender system was designed and created, capable of obtaining movies recommendation from the database based on the user's preferences. Next, we verified experimentally which recommender system produces more accurate results.

  6. Optimal operating conditions for maximum biogas production in anaerobic bioreactors

    International Nuclear Information System (INIS)

    Balmant, W.; Oliveira, B.H.; Mitchell, D.A.; Vargas, J.V.C.; Ordonez, J.C.

    2014-01-01

    The objective of this paper is to demonstrate the existence of optimal residence time and substrate inlet mass flow rate for maximum methane production through numerical simulations performed with a general transient mathematical model of an anaerobic biodigester introduced in this study. It is herein suggested a simplified model with only the most important reaction steps which are carried out by a single type of microorganisms following Monod kinetics. The mathematical model was developed for a well mixed reactor (CSTR – Continuous Stirred-Tank Reactor), considering three main reaction steps: acidogenesis, with a μ max of 8.64 day −1 and a K S of 250 mg/L, acetogenesis, with a μ max of 2.64 day −1 and a K S of 32 mg/L, and methanogenesis, with a μ max of 1.392 day −1 and a K S of 100 mg/L. The yield coefficients were 0.1-g-dry-cells/g-pollymeric compound for acidogenesis, 0.1-g-dry-cells/g-propionic acid and 0.1-g-dry-cells/g-butyric acid for acetogenesis and 0.1 g-dry-cells/g-acetic acid for methanogenesis. The model describes both the transient and the steady-state regime for several different biodigester design and operating conditions. After model experimental validation, a parametric analysis was performed. It was found that biogas production is strongly dependent on the input polymeric substrate and fermentable monomer concentrations, but fairly independent of the input propionic, acetic and butyric acid concentrations. An optimisation study was then conducted and optimal residence time and substrate inlet mass flow rate were found for maximum methane production. The optima found were very sharp, showing a sudden drop of methane mass flow rate variation from the observed maximum to zero, within a 20% range around the optimal operating parameters, which stresses the importance of their identification, no matter how complex the actual bioreactor design may be. The model is therefore expected to be a useful tool for simulation, design, control and

  7. Semantically Enhanced Recommender Systems

    Science.gov (United States)

    Ruiz-Montiel, Manuela; Aldana-Montes, José F.

    Recommender Systems have become a significant area in the context of web personalization, given the large amount of available data. Ontologies can be widely taken advantage of in recommender systems, since they provide a means of classifying and discovering of new information about the items to recommend, about user profiles and even about their context. We have developed a semantically enhanced recommender system based on this kind of ontologies. In this paper we present a description of the proposed system.

  8. The toxicological significance of post-mortem drug concentrations in bile.

    Science.gov (United States)

    Ferner, Robin E; Aronson, Jeffrey K

    2018-01-01

    Some authors have proposed that post-mortem drug concentrations in bile are useful in estimating concentrations in blood. Both The International Association of Forensic Toxicologists (TIAFT) and the US Federal Aviation Administration recommend that samples of bile should be obtained in some circumstances. Furthermore, standard toxicological texts compare blood and bile concentrations, implying that concentrations in bile are of forensic value. To review the evidence on simultaneous measurements of blood and bile drug concentrations reported in the medical literature. We made a systematic search of EMBASE 1980-2016 using the search terms ("bile/" OR "exp drug bile level/concentration/") AND "drug blood level/concentration/", PubMed 1975-2017 for ("bile[tw]" OR "biliary[tw]") AND ("concentration[tw]" OR "concentrations[tw]" OR "level[tw]" OR "levels[tw]") AND "post-mortem[tw]" and also MEDLINE 1990-2016 for information on drugs whose biliary concentrations were mentioned in standard textbooks. The search was limited to human studies without language restrictions. We also examined recent reviews, indexes of relevant journals and citations in Web of Science and Google Scholar. We calculated the bile:blood concentration ratio. The searches together yielded 1031 titles with abstracts. We scanned titles and abstracts for relevance and retrieved 230, of which 161 were considered further. We excluded 49 papers because: the paper reported only one case (30 references); the data referred only to a metabolite (1); the work was published before 1980 (3); the information concerned only samples taken during life (10); or the paper referred to a toxin or unusual recreational drug (5). The remaining 112 papers provided data for analysis, with at least two observations for each of 58 drugs. Bile:blood concentration ratios: Median bile:blood concentration ratios varied from 0.18 (range 0.058-0.32) for dextromoramide to 520 (range 0.62-43,000) for buprenorphine. Median bile

  9. Stress concentration factors for pressurized elliptic crossbores in blocks

    International Nuclear Information System (INIS)

    Badr, Elie A.

    2006-01-01

    Intersecting bore geometries are used in a number of industrial applications including heavy-walled pressure vessels containing oil holes for lubrication, ports for valves and fluid ends of reciprocating pumps. The bore intersection location is a stress concentration point where the maximum hoop stress can be many times the fluid pressure in the bores. Intersecting circular holes in heavy-walled cylinders and rectangular blocks have been extensively investigated. Specifically, stress/pressure concentration curves for intersecting circular bores in rectangular blocks were presented by Sorem et al. [Sorem JR, Shadley JR, Tipton SM. Design curves for maximum stresses in blocks containing pressurized bore intersections. ASME J Mech Des 1990; 113: 427-31.]. However, stress/pressure concentrations due to intersecting elliptic bores have not been broadly investigated. With the availability of computer numerical control (CNC) machinery, bores with elliptic crosssection can be produced with relative ease. In this paper, hoop stress concentration ratios are developed for elliptic crossbores in rectangular blocks. Results indicate that introducing elliptic crossbores, rather than circular ones, significantly reduces the hoop stress concentration factor at the crossbore intersection. Also, the presence of intersecting crossbores has a major effect on the fatigue life of pressure vessels [Badr EA, Sorem JR, Jr Tipton SM. Evaluation of the autofrettage effect on fatigue lives of steel blocks with crossbores using a statistical and a strain-based method. ASTM J Test Eval 2000; 28: 181-8.] and the reduction of hoop stress concentration is expected to enhance the fatigue life of pressure vessels containing crossbores

  10. Towards Information Enrichment through Recommendation Sharing

    Science.gov (United States)

    Weng, Li-Tung; Xu, Yue; Li, Yuefeng; Nayak, Richi

    Nowadays most existing recommender systems operate in a single organisational basis, i.e. a recommender system recommends items to customers of one organisation based on the organisation's datasets only. Very often the datasets of a single organisation do not have sufficient resources to be used to generate quality recommendations. Therefore, it would be beneficial if recommender systems of different organisations with similar nature can cooperate together to share their resources and recommendations. In this chapter, we present an Ecommerce-oriented Distributed Recommender System (EDRS) that consists of multiple recommender systems from different organisations. By sharing resources and recommendations with each other, these recommenders in the distributed recommendation system can provide better recommendation service to their users. As for most of the distributed systems, peer selection is often an important aspect. This chapter also presents a recommender selection technique for the proposed EDRS, and it selects and profiles recommenders based on their stability, average performance and selection frequency. Based on our experiments, it is shown that recommenders' recommendation quality can be effectively improved by adopting the proposed EDRS and the associated peer selection technique.

  11. Concentration of lead and zinc in greenhouse cucumbers of Hamadan province in 2012

    Directory of Open Access Journals (Sweden)

    Z BigMohammadi

    2013-08-01

    Full Text Available Heavy metal pollution of agricultural soils is a major environmental problem that can affect plant production, food safety and human health. Soil contamination with heavy metals occurs as a result of human activities. Heavy metals can easily accumulate in edible tissues of leafy vegetables, fruits and seeds. Few studies have been conducted on heavy metals concentration in soil and greenhouse crops. Therefore, this study aimed to determine the concentrations of lead (Pb and zinc (Zn in greenhouse cucumbers produced in Hamadan province. The concentrations of heavy metals were measured using atomic emission method. Results showed that the mean concentrations of Pb and Zn in cucumber samples were 0.33 and 3.14 mg/kg, respectively. Also the results of the statistical analysis revealed a negative correlation between the measured concentrations. Moreover, the concentration of Zn in the samples obtained from Hamadan greenhouses and lead concentration in Tuyserkan, Famenin, as well as Malayer samples were above the recommended limits. Daily intake amounts of Pb and Zn from vegetables consumption for three age categories (children, adolescents, and adults were calculated. In conclusion, daily intake of Pb and Zn were determined below the recommended limits.

  12. 78 FR 9845 - Minimum and Ordinary Maximum and Aggravated Maximum Civil Monetary Penalties for a Violation of...

    Science.gov (United States)

    2013-02-12

    ... maximum penalty amount of $75,000 for each violation, except that if the violation results in death... the maximum civil penalty for a violation is $175,000 if the violation results in death, serious... Penalties for a Violation of the Hazardous Materials Transportation Laws or Regulations, Orders, Special...

  13. How do changes in bulk soil organic carbon content affect carbon concentrations in individual soil particle fractions?

    Science.gov (United States)

    Yang, X. M.; Drury, C. F.; Reynolds, W. D.; Yang, J. Y.

    2016-06-01

    We test the common assumption that organic carbon (OC) storage occurs on sand-sized soil particles only after the OC storage capacity on silt- and clay-sized particles is saturated. Soil samples from a Brookston clay loam in Southwestern Ontario were analysed for the OC concentrations in bulk soil, and on the clay (<2 μm), silt (2-53 μm) and sand (53-2000 μm) particle size fractions. The OC concentrations in bulk soil ranged from 4.7 to 70.8 g C kg-1 soil. The OC concentrations on all three particle size fractions were significantly related to the OC concentration of bulk soil. However, OC concentration increased slowly toward an apparent maximum on silt and clay, but this maximum was far greater than the maximum predicted by established C sequestration models. In addition, significant increases in OC associated with sand occurred when the bulk soil OC concentration exceeded 30 g C kg-1, but this increase occurred when the OC concentration on silt + clay was still far below the predicted storage capacity for silt and clay fractions. Since the OC concentrations in all fractions of Brookston clay loam soil continued to increase with increasing C (bulk soil OC content) input, we concluded that the concept of OC storage capacity requires further investigation.

  14. Tritium concentrations in tree ring cellulose

    International Nuclear Information System (INIS)

    Kaji, Toshio; Momoshima, Noriyuki; Takashima, Yoshimasa.

    1989-01-01

    Measurements of tritium (tissue bound tritium; TBT) concentration in tree rings are presented and discussed. Such measurement is expected to provide a useful means of estimating the tritium level in the environment in the past. The concentration of tritium bound in the tissue (TBT) in a tree ring considered to reflect the environmental tritium level in the area at the time of the formation of the ring, while the concentration of tritium in the free water in the tissue represents the current environmental tritium level. First, tritium concentration in tree ring cellulose sampled from a cedar tree grown in a typical environment in Fukuoka Prefecture is compared with the tritium concentration in precipitation in Tokyo. Results show that the year-to-year variations in the tritium concentration in the tree rings agree well with those in precipitation. The maximum concentration, which occurred in 1963, is attibuted to atmospheric nuclear testing which was performed frequently during the 1961 - 1963 period. Measurement is also made of the tritium concentration in tree ring cellulose sampled from a pine tree grown near the Isotope Center of Kyushu University (Fukuoka). Results indicate that the background level is higher probably due to the release of tritium from the facilities around the pine tree. Thus, measurement of tritium in tree ring cellulose clearly shows the year-to-year variation in the tritium concentration in the atmosphere. (N.K.)

  15. Subtropical Arctic Ocean temperatures during the Palaeocene/Eocene thermal maximum

    Science.gov (United States)

    Sluijs, A.; Schouten, S.; Pagani, M.; Woltering, M.; Brinkhuis, H.; Damste, J.S.S.; Dickens, G.R.; Huber, M.; Reichart, G.-J.; Stein, R.; Matthiessen, J.; Lourens, L.J.; Pedentchouk, N.; Backman, J.; Moran, K.; Clemens, S.; Cronin, T.; Eynaud, F.; Gattacceca, J.; Jakobsson, M.; Jordan, R.; Kaminski, M.; King, J.; Koc, N.; Martinez, N.C.; McInroy, D.; Moore, T.C.; O'Regan, M.; Onodera, J.; Palike, H.; Rea, B.; Rio, D.; Sakamoto, T.; Smith, D.C.; St John, K.E.K.; Suto, I.; Suzuki, N.; Takahashi, K.; Watanabe, M. E.; Yamamoto, M.

    2006-01-01

    The Palaeocene/Eocene thermal maximum, ???55 million years ago, was a brief period of widespread, extreme climatic warming, that was associated with massive atmospheric greenhouse gas input. Although aspects of the resulting environmental changes are well documented at low latitudes, no data were available to quantify simultaneous changes in the Arctic region. Here we identify the Palaeocene/Eocene thermal maximum in a marine sedimentary sequence obtained during the Arctic Coring Expedition. We show that sea surface temperatures near the North Pole increased from ???18??C to over 23??C during this event. Such warm values imply the absence of ice and thus exclude the influence of ice-albedo feedbacks on this Arctic warming. At the same time, sea level rose while anoxic and euxinic conditions developed in the ocean's bottom waters and photic zone, respectively. Increasing temperature and sea level match expectations based on palaeoclimate model simulations, but the absolute polar temperatures that we derive before, during and after the event are more than 10??C warmer than those model-predicted. This suggests that higher-than-modern greenhouse gas concentrations must have operated in conjunction with other feedback mechanisms-perhaps polar stratospheric clouds or hurricane-induced ocean mixing-to amplify early Palaeogene polar temperatures. ?? 2006 Nature Publishing Group.

  16. Performance analysis and comparison of an Atkinson cycle coupled to variable temperature heat reservoirs under maximum power and maximum power density conditions

    International Nuclear Information System (INIS)

    Wang, P.-Y.; Hou, S.-S.

    2005-01-01

    In this paper, performance analysis and comparison based on the maximum power and maximum power density conditions have been conducted for an Atkinson cycle coupled to variable temperature heat reservoirs. The Atkinson cycle is internally reversible but externally irreversible, since there is external irreversibility of heat transfer during the processes of constant volume heat addition and constant pressure heat rejection. This study is based purely on classical thermodynamic analysis methodology. It should be especially emphasized that all the results and conclusions are based on classical thermodynamics. The power density, defined as the ratio of power output to maximum specific volume in the cycle, is taken as the optimization objective because it considers the effects of engine size as related to investment cost. The results show that an engine design based on maximum power density with constant effectiveness of the hot and cold side heat exchangers or constant inlet temperature ratio of the heat reservoirs will have smaller size but higher efficiency, compression ratio, expansion ratio and maximum temperature than one based on maximum power. From the view points of engine size and thermal efficiency, an engine design based on maximum power density is better than one based on maximum power conditions. However, due to the higher compression ratio and maximum temperature in the cycle, an engine design based on maximum power density conditions requires tougher materials for engine construction than one based on maximum power conditions

  17. Flow-covariate prediction of stream pesticide concentrations.

    Science.gov (United States)

    Mosquin, Paul L; Aldworth, Jeremy; Chen, Wenlin

    2018-01-01

    Potential peak functions (e.g., maximum rolling averages over a given duration) of annual pesticide concentrations in the aquatic environment are important exposure parameters (or target quantities) for ecological risk assessments. These target quantities require accurate concentration estimates on nonsampled days in a monitoring program. We examined stream flow as a covariate via universal kriging to improve predictions of maximum m-day (m = 1, 7, 14, 30, 60) rolling averages and the 95th percentiles of atrazine concentration in streams where data were collected every 7 or 14 d. The universal kriging predictions were evaluated against the target quantities calculated directly from the daily (or near daily) measured atrazine concentration at 32 sites (89 site-yr) as part of the Atrazine Ecological Monitoring Program in the US corn belt region (2008-2013) and 4 sites (62 site-yr) in Ohio by the National Center for Water Quality Research (1993-2008). Because stream flow data are strongly skewed to the right, 3 transformations of the flow covariate were considered: log transformation, short-term flow anomaly, and normalized Box-Cox transformation. The normalized Box-Cox transformation resulted in predictions of the target quantities that were comparable to those obtained from log-linear interpolation (i.e., linear interpolation on the log scale) for 7-d sampling. However, the predictions appeared to be negatively affected by variability in regression coefficient estimates across different sample realizations of the concentration time series. Therefore, revised models incorporating seasonal covariates and partially or fully constrained regression parameters were investigated, and they were found to provide much improved predictions in comparison with those from log-linear interpolation for all rolling average measures. Environ Toxicol Chem 2018;37:260-273. © 2017 SETAC. © 2017 SETAC.

  18. Recommender systems

    CERN Document Server

    Kembellec, Gérald; Saleh, Imad

    2014-01-01

    Acclaimed by various content platforms (books, music, movies) and auction sites online, recommendation systems are key elements of digital strategies. If development was originally intended for the performance of information systems, the issues are now massively moved on logical optimization of the customer relationship, with the main objective to maximize potential sales. On the transdisciplinary approach, engines and recommender systems brings together contributions linking information science and communications, marketing, sociology, mathematics and computing. It deals with the understan

  19. Spatial distribution of ground-level urban background O3 concentrations in the Metropolitan Area of Buenos Aires, Argentina

    International Nuclear Information System (INIS)

    Pineda Rojas, Andrea L.; Venegas, Laura E.

    2013-01-01

    In this work, a recently developed urban-scale atmospheric dispersion model (DAUMOD-GRS) is applied to evaluate the ground-level ozone (O 3 ) concentrations resulting from anthropogenic area sources of NO x and VOC in the Metropolitan Area of Buenos Aires (MABA). The statistical comparison of model results with observations (including new available data from seventeen sites) shows a good model performance. Estimated summer highest diurnal O 3 1-h concentrations in the MABA vary between 15 ppb in the most urbanised area and 53 ppb in the suburbs. All values are below the air quality standard. Several runs are performed to evaluate the impact of possible future emission reductions on O 3 concentrations. Under all hypothetical scenarios, the maximum diurnal O 3 1-h concentration obtained for the area is slightly reduced (up to 4%). However, maximum diurnal O 3 concentrations could increase at some less urbanised areas of MABA depending on the relative reductions of the emissions of NO x and VOC. -- Highlights: ► A recently developed air quality model reproduces well observed O 3 levels in MABA. ► Modelled summer maximum diurnal O 3 concentrations vary in the area between 15 and 53 ppb. ► All hourly values are below the air quality standard (120 ppb). ► Possible future emission reductions would have small impact on the highest level. -- The distribution of summer maximum diurnal ground-level O 3 concentrations in the Metropolitan Area of Buenos Aires is evaluated applying a recently developed simple urban air quality model

  20. Growth and xanthan production of Xanthomonas campestris depending on the N-source concentration

    Energy Technology Data Exchange (ETDEWEB)

    Prell, A [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology; Lasik, J [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology; Konicek, J [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology; Sobotka, M [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology; Sys, J [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology

    1995-11-01

    Growth of X. campestris and production of xanthan were studied in several batch fermentations with different starting concentrations of N-source. The dependencies of growth, productivity and yields on initial N-source concentration were observed. The maximum yields in the course of cultivations were identified. (orig.)

  1. Urine Concentration and Pyuria for Identifying UTI in Infants.

    Science.gov (United States)

    Chaudhari, Pradip P; Monuteaux, Michael C; Bachur, Richard G

    2016-11-01

    Varying urine white blood cell (WBC) thresholds have been recommended for the presumptive diagnosis of urinary tract infection (UTI) among young infants. These thresholds have not been studied with newer automated urinalysis systems that analyze uncentrifuged urine that might be influenced by urine concentration. Our objective was to determine the optimal urine WBC threshold for UTI in young infants by using an automated urinalysis system, stratified by urine concentration. Retrospective cross-sectional study of infants aged UTI in the emergency department with paired urinalysis and urine culture. UTI was defined as ≥50 000 colony-forming units/mL from catheterized specimens. Test characteristics were calculated across a range of WBC and leukocyte esterase (LE) cut-points, dichotomized into specific gravity groups (dilute UTI prevalence was 7.8%. Optimal WBC cut-points were 3 WBC/high-power field (HPF) in dilute urine (likelihood ratio positive [LR+] 9.9, likelihood ratio negative [LR‒] 0.15) and 6 WBC/HPF (LR+ 10.1, LR‒ 0.17) in concentrated urine. For dipstick analysis, positive LE has excellent test characteristics regardless of urine concentration (LR+ 22.1, LR‒ 0.12 in dilute urine; LR+ 31.6, LR‒ 0.22 in concentrated urine). Urine concentration should be incorporated into the interpretation of automated microscopic urinalysis in young infants. Pyuria thresholds of 3 WBC/HPF in dilute urine and 6 WBC/HPF in concentrated urine are recommended for the presumptive diagnosis of UTI. Without correction of specific gravity, positive LE by automated dipstick is a reliably strong indicator of UTI. Copyright © 2016 by the American Academy of Pediatrics.

  2. Asymmetric design for Compound Elliptical Concentrators (CEC) and its geometric flux implications

    Science.gov (United States)

    Jiang, Lun; Winston, Roland

    2015-08-01

    The asymmetric compound elliptical concentrator (CEC) has been a less discussed subject in the nonimaging optics society. The conventional way of understanding an ideal concentrator is based on maximizing the concentration ratio based on a uniformed acceptance angle. Although such an angle does not exist in the case of CEC, the thermodynamic laws still hold and we can produce concentrators with the maximum concentration ratio allowed by them. Here we restate the problem and use the string method to solve this general problem. Built on the solution, we can discover groups of such ideal concentrators using geometric flux field, or flowline method.

  3. Dependency of maximum goitrogenic response on some minimal level of thyroid hormone production

    International Nuclear Information System (INIS)

    March, B.E.; Poon, R.

    1981-01-01

    Thyroidal activity was studied in chicks given dietary thiouracil in conjunction with daily doses of thyroxine and with diets adequate and deficient in iodine. DL-thyroxine administered at doses up to 1.0 microgram per day for 10 to 12 days had no effect or slightly increased thyroid weight. Both the epithelial and colloid components of the thyroid gland were increased in response to thiouracil and to thiouracil in combination with low dosages of exogenous thyroxine. Radioiodine uptake was increased above the control with thiouracil and with thiouracil in conjunction with .5 and 1.0 microgram DL-thyroxine given daily. Birds receiving thiouracil, with and without exogenous thyroxine, showed a different pattern of radioiodine uptake and release than the control birds. Thiouracil-treated birds showed a rapid uptake of iodine following its administration, which was followed by a rapid decline immediately after peak accumulation, whereas in control birds thyroidal radioiodine concentration reached a plateau at the maximum concentration attained. The goitrogenic response to thiouracil was much greater when the diet was supplemented with iodine than when the diet was iodine-deficient. Thyroids under iodine deficiency contained greater percentages of epithelial tissue than with iodine-supplemented diets. Thyroid glands of chicks given thiouracil in an iodine-supplemented diet contained much more colloid than glands from iodine-deficient chicks with or without thiouracil. DL-thyroxine at a dosage of .5 microgram per day to chicks given thiouracil in an iodine-adequate diet increased, whereas higher dosages decreased thyroidal colloid. It is concluded that some minimal concentration of thyroid hormone is required for maximum goitrogenic response. It is not clear whether the response is entirely due to an effect on thyrotropin production or whether there is an effect of thyroid hormone on the thyroid gland itself

  4. Recommender Systems in Commercial Use

    OpenAIRE

    Aldrich, Susan E.

    2011-01-01

    Commercial recommender systems are deployed by marketing teams to increase revenue and/or personalize user experience. Marketers evaluate recommender systems not on its algorithms but on how well the vendor‘s expertise and interfaces will support achieving business goals. Driven by a business model that pays based on recommendation success, vendors guide clients through continuous optimization of recommendations. While recommender technology is mature, the solutions and market are still young...

  5. Urinary Concentrating Ability in Women with Asymptomatic Bacteriuria in Pregnancy

    Science.gov (United States)

    Williams, G. L.; Campbell, H.; Davies, K. J.

    1969-01-01

    The incidence of impaired renal concentrating ability in pregnant women with asymptomatic significant bacteriuria is significantly less than previously reported when osmolality readings are performed on every urine specimen obtained during the 24 hours' deprivation of fluids. The concentrating defect is more considerable as pregnancy progresses. The lower the maximum urinary osmolality the more difficult is the treatment of the patient, and the higher the incidence of acute pyelonephritis. PMID:5792611

  6. Handling of membrane concentrate from reclamation of water in polyester dyeing

    DEFF Research Database (Denmark)

    Villanueva, Alejandro; Wenzel, Henrik; Knudsen, Hans Henrik

    2003-01-01

    incineration, wet air oxidation, activated carbon, transport to hazardous waste treatment facility, and drying for zero-discharge. In most disposal scenarios considered it is advantageous to dewater the concentrate further from 2,5 %DS (dry solids) to 20 %DS in order to reduce its volume and thereby diminish...... recycling projects where the concentrate has low or no commercial value. In the scenarios analyzed, concentrate disposal costs represents between 10% and 70% of the total treatment costs per m3 of water recycled. It is therefore recommended to analyze in detail the available alternatives for concentrate...

  7. Handling of Membrane Concentrate from Reclamation of Water in Polyester Dyeing

    DEFF Research Database (Denmark)

    Villanueva, Alejandro; Wenzel, Henrik; Knudsen, Hans Henrik

    2003-01-01

    incineration, wet air oxidation, activated carbon, transport to hazardous waste treatment facility, and drying for zero-discharge. In most disposal scenarios considered it is advantageous to dewater the concentrate further from 2,5 %DS (dry solids) to 20 %DS in order to reduce its volume and thereby diminish...... recycling projects where the concentrate has low or no commercial value. In the scenarios analyzed, concentrate disposal costs represents between 10% and 70% of the total treatment costs per m3 of water recycled. It is therefore recommended to analyze in detail the available alternatives for concentrate...

  8. Uranium concentrations in the water consumed by the resident population in the vicinity of the Lagoa Real uranium province, Bahia, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Luciana S. [State University of Bahia (UNEB), Campus Caetite, BA (Brazil); Pecequilo, Brigitte R.S.; Sarkis, Jorge; Nisti, Marcelo B., E-mail: brigitte@ipen.br, E-mail: jesarkis@ipen.br, E-mail: mbnisti@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    The Lagoa Real Uranium Province, situated in South Central Bahia in the region of Caetite and Lagoa Real, is considered the most important monomineralic province of Brazil. The urban population who lives in the proximities of this uranium province in the cities of Caetite, Lagoa Real and Livramento uses public supply water, while the inhabitants of the rural area due to long terms of dry weather use water from wells, cisterns, small dams, reservoirs and dikes which are supplied with the rains. In this work it was determined the concentration of uranium in the water consumed by the rural and urban population living in the proximities of the Lagoa Real Uranium Province. The study comprehends 32 sampling spots spread throughout the region of interest. Samples were collected in January and July 2010, covering superficial, underground and public supply water from the region. The uranium concentrations were determined by an inductively coupled plasma mass spectrometer (ICP-MS). Preliminary results showed that the uranium concentrations in the water from the Lagoa Real Uranium Province varied from 0.064 {+-} 0.005 {mu}g.L{sup -1} to 90 {+-} 1,5 {+-}g.L{sup -1}. It was observed that only two of them obtained values higher than the World Health Organization's recommended limit (2011) of 30 {mu}g.L{sup -1} for maximum uranium concentration in the water for human consumption. For a conclusive evaluation, the uranium concentrations results will be analyzed together with total alpha and beta concentrations determined elsewhere for the same samples. (author)

  9. Uranium concentrations in the water consumed by the resident population in the vicinity of the Lagoa Real uranium province, Bahia, Brazil

    International Nuclear Information System (INIS)

    Silva, Luciana S.; Pecequilo, Brigitte R.S.; Sarkis, Jorge; Nisti, Marcelo B.

    2011-01-01

    The Lagoa Real Uranium Province, situated in South Central Bahia in the region of Caetite and Lagoa Real, is considered the most important monomineralic province of Brazil. The urban population who lives in the proximities of this uranium province in the cities of Caetite, Lagoa Real and Livramento uses public supply water, while the inhabitants of the rural area due to long terms of dry weather use water from wells, cisterns, small dams, reservoirs and dikes which are supplied with the rains. In this work it was determined the concentration of uranium in the water consumed by the rural and urban population living in the proximities of the Lagoa Real Uranium Province. The study comprehends 32 sampling spots spread throughout the region of interest. Samples were collected in January and July 2010, covering superficial, underground and public supply water from the region. The uranium concentrations were determined by an inductively coupled plasma mass spectrometer (ICP-MS). Preliminary results showed that the uranium concentrations in the water from the Lagoa Real Uranium Province varied from 0.064 ± 0.005 μg.L -1 to 90 ± 1,5 ±g.L -1 . It was observed that only two of them obtained values higher than the World Health Organization's recommended limit (2011) of 30 μg.L -1 for maximum uranium concentration in the water for human consumption. For a conclusive evaluation, the uranium concentrations results will be analyzed together with total alpha and beta concentrations determined elsewhere for the same samples. (author)

  10. [MAXIMUM SINGLE DOSE OF COLLOIDAL SILVER NEGATIVELY AFFECTS ERYTHROPOIESIS IN VITRO].

    Science.gov (United States)

    Tishevskayal, N V; Zakharovl, Y M; Bolotovl, A A; Arkhipenko, Yu V; Sazontova, T G

    2015-01-01

    Erythroblastic islets (EI) of rat bone marrow were cultured for 24 h in the presence of silver nanoparticles (1.07 · 10(-4) mg/ml; 1.07 · 10(-3) mg/ml; and 1.07 · 10(-2) mg/mL). The colloidal silver at 1.07 · 10(-3) mg/ml concentration inhibited the formation of new Elby disrupting contacts of bone marrow macrophages with CFU-E (erythropoiesis de novo) by 65.3% (p Colloidal silver nanoparticles suppressed the reconstruction of erythropoiesis and inhibited the formation of new EI by disrupting contacts of CFU-E and central macrophages with matured erythroidal "crown" (erythropoiesis de repeto). The colloidal silver concentration of 1.07 · 10(-3) mg/ml in the culture medium also reduced the number of self-reconstructing EI by 67.5% (p colloidal silver reduced this value by 93.7% (p Silver nanoparticles retarded maturation of erythroid cells at the stage of oxiphylic normoblast denucleation: 1.07 · 10(-3) mg/ml colloidal silver increased the number of mature El by 53% (p colloidal silver in concentration equivalent to the maximum single dose is related to the effect of silver nanoparticles rather than glycerol present in the colloidal suspension.

  11. Sound levels in a neonatal intensive care unit significantly exceeded recommendations, especially inside incubators.

    Science.gov (United States)

    Parra, Johanna; de Suremain, Aurelie; Berne Audeoud, Frederique; Ego, Anne; Debillon, Thierry

    2017-12-01

    This study measured sound levels in a 2008 built French neonatal intensive care unit (NICU) and compared them to the 2007 American Academy of Pediatrics (AAP) recommendations. The ultimate aim was to identify factors that could influence noise levels. The study measured sound in 17 single or double rooms in the NICU. Two dosimeters were installed in each room, one inside and one outside the incubators, and these conducted measurements over a 24-hour period. The noise metrics measured were the equivalent continuous sound level (L eq ), the maximum noise level (L max ) and the noise level exceeded for 10% of the measurement period (L 10 ). The mean L eq , L 10 and L max were 60.4, 62.1 and 89.1 decibels (dBA), which exceeded the recommended levels of 45, 50 and 65 dBA (p care was correlated to an increased noise level, except for a postconceptional age below 32 weeks. The sound levels significantly exceeded the AAP recommendations, particularly inside incubators. A multipronged strategy is required to improve the sound environment and protect the neonates' sensory development. ©2017 Foundation Acta Paediatrica. Published by John Wiley & Sons Ltd.

  12. Development of compound parabolic concentrators for solar energy

    Energy Technology Data Exchange (ETDEWEB)

    O' Gallagher, J.; Winston, R.

    1983-10-01

    The compound parabolic concentrator (CPC) is not a specific collector, but a family of collectors based on a general design principle for maximizing the geometric concentration, C, for radiation within a given acceptance half angle = thetac. This maximum limit exceeds by a factor of 2 to 4 that attainable by systems using focussing optics. The wide acceptance angles permitted using these techniques have several unique advantages for solar concentrators including the elimination of the diurnal tracking requirement at intermediate concentrations (up to about 10x), collection of circumsolar and some diffuse radiation and relaxed tolerances. Because of these advantages, CPC type concentrators have applications in solar energy wherever concentration is desired, e.g., for a wide variety of both thermal and photovoltaic uses. The basic principles of nonimaging optical design are reviewed. Selected configurations for both non-evacuated and evacuated thermal collector applications are discussed with particular emphasis on the most recent advances. The use of CPC type elements as secondary concentrators is illustrated in the context of higher concentration photovoltaic applications.

  13. Planar waveguide concentrator used with a seasonal tracker.

    Science.gov (United States)

    Bouchard, Sébastien; Thibault, Simon

    2012-10-01

    Solar concentrators offer good promise for reducing the cost of solar power. Planar waveguides equipped with a microlens slab have already been proposed as an excellent approach to produce medium to high concentration levels. Instead, we suggest the use of a cylindrical microlens array to get useful concentration without tracking during the day. To use only a seasonal tracking system and get the highest possible concentration, cylindrical microlenses are placed in the east-west orientation. Our new design has an acceptance angle in the north-south direction of ±9° and ±54° in the east-west axis. Simulation of our optimized system achieves a 4.6× average concentration level from 8:30 to 16:30 with a maximum of 8.1× and 80% optical efficiency. The low-cost advantage of waveguide-based solar concentrators could support their use in roof-mounted solar panels and eliminate the need for an expensive and heavy active tracker.

  14. Regulatory Forum Opinion Piece*: Retrospective Evaluation of Doses in the 26-week Tg.rasH2 Mice Carcinogenicity Studies: Recommendation to Eliminate High Doses at Maximum Tolerated Dose (MTD) in Future Studies.

    Science.gov (United States)

    Paranjpe, Madhav G; Denton, Melissa D; Vidmar, Tom J; Elbekai, Reem H

    2015-07-01

    High doses in Tg.rasH2 carcinogenicity studies are usually set at the maximum tolerated dose (MTD), although this dose selection strategy has not been critically evaluated. We analyzed the body weight gains (BWGs), mortality, and tumor response in control and treated groups of 29 Tg.rasH2 studies conducted at BioReliance. Based on our analysis, it is evident that the MTD was exceeded at the high and/or mid-doses in several studies. The incidence of tumors in high doses was lower when compared to the low and mid-doses of both sexes. Thus, we recommend that the high dose in male mice should not exceed one-half of the estimated MTD (EMTD), as it is currently chosen, and the next dose should be one-fourth of the EMTD. Because females were less sensitive to decrements in BWG, the high dose in female mice should not exceed two-third of EMTD and the next dose group should be one-third of EMTD. If needed, a third dose group should be set at one-eighth EMTD in males and one-sixth EMTD in females. In addition, for compounds that do not show toxicity in the range finding studies, a limit dose should be applied for the 26-week carcinogenicity studies. © 2014 by The Author(s).

  15. Ten years of continual monitoring of 222Rn concentration in Bratislava atmosphere

    International Nuclear Information System (INIS)

    Holy, K.; Bosa, I.; Polaskova, A.; Boehm, R.; Ondo-Estok, D.; Bulko, M.; Hola, O.

    2003-01-01

    By the continual monitoring we obtained the extensive set of radon data in Bratislava atmosphere covering the time period of 1991 - 2000. The average annual radon activity concentrations varied from 4.1 to 7.2 Bq/m 3 . In the years 1996 - 1999 the decreasing of the average annual radon concentration was observed. The average daily courses of the radon activity concentration for individual months calculated on the basis of all data from 1991 - 2000 have a form of waves with the maximum in morning hours and with the minimum in the afternoon. The maximal amplitude of daily wave was found out in August (2.9 Bq/m 3 ) and minimal in December (0.5 Bq/m 3 ). The average daily wave obtained as the mean off all data from years 1991 - 2000 reaches the maximum between 4 and 6 a. m. and the minimum between 2 and 4 p. m. The Rn-222 activity concentration reaches its average daily value equal to 5.6 Bq/m 3 at about 10 a. m and at 9 p. m. The amplitude of average daily wave is equal to 1.5 Bq/m 3 . The average annual radon course calculated on the basis of all the measured data reaches the minimum in April and the maximum in October with seasonal variation from 3.9 to 6.9 Bq/m 3 . The annual radon courses differ from each other for various periods of the day. (authors)

  16. Concentration of Mercury in Cockles (Anadara granosa and A. antiquata) Harvested from Estuaries of Western Lombok, Indonesia, and Potential Risks to Human Health.

    Science.gov (United States)

    Rahayu, Rachmawati Noviana; Irawan, Bambang; Soegianto, Agoes

    2016-01-01

    This study measured the levels of total mercury (tHg) in the whole tissues of cockles (Anadara granosa and A. antiquata) harvested from three estuaries of Western Lombok Island (WLI), Indonesia. This paper also evaluated the hazard level posed by the mercury in relation to the maximum residual limit for human consumption and to estimate the weekly intake and compare it with the provisional tolerable weekly intake (PTWI). The tHg concentrations in A. granosa ranged from 0.020 to 0.070 mg kg(-1), and those in A. antiquata were between 0.032 and 0.077 mg kg(-1) at all locations. All samples of cockles harvested from WLI contain tHg below the permissible limit for human consumption. The maximum weekly intakes for total mercury by coastal people range from 0.28 to 1.08 µg kg(-1) b.w., and they are below the recommended values of PTWI (5.6 µg kg(-1) b.w.). If it is assumed that 100% of the Hg in cockles is methyl mercury (MeHg), consumption of the indicated amounts at the measured values wouldn't exceed the MeHg PTWI (1.6 µg kg(-1) b.w.).

  17. Applications of maximally concentrating optics for solar energy collection

    Science.gov (United States)

    O'Gallagher, J.; Winston, R.

    1985-11-01

    A new family of optical concentrators based on a general nonimaging design principle for maximizing the geometric concentration, C, for radiation within a given acceptance half angle ±θα has been developed. The maximum limit exceeds by factors of 2 to 10 that attainable by systems using focusing optics. The wide acceptance angles permitted using these techniques have several unique advantages for solar concentrators including the elimination of the diurnal tracking requirement at intermediate concentrations (up to ˜10x), collection of circumsolar and some diffuse radiation, and relaxed tolerances. Because of these advantages, these types of concentrators have applications in solar energy wherever concentration is desired, e.g. for a wide variety of both thermal and photovoltaic uses. The basic principles of nonimaging optical design are reviewed. Selected configurations for thermal collector applications are discussed and the use of nonimaging elements as secondary concentrators is illustrated in the context of higher concentration applications.

  18. LCLS Maximum Credible Beam Power

    International Nuclear Information System (INIS)

    Clendenin, J.

    2005-01-01

    The maximum credible beam power is defined as the highest credible average beam power that the accelerator can deliver to the point in question, given the laws of physics, the beam line design, and assuming all protection devices have failed. For a new accelerator project, the official maximum credible beam power is determined by project staff in consultation with the Radiation Physics Department, after examining the arguments and evidence presented by the appropriate accelerator physicist(s) and beam line engineers. The definitive parameter becomes part of the project's safety envelope. This technical note will first review the studies that were done for the Gun Test Facility (GTF) at SSRL, where a photoinjector similar to the one proposed for the LCLS is being tested. In Section 3 the maximum charge out of the gun for a single rf pulse is calculated. In Section 4, PARMELA simulations are used to track the beam from the gun to the end of the photoinjector. Finally in Section 5 the beam through the matching section and injected into Linac-1 is discussed

  19. A Flexible Electronic Commerce Recommendation System

    Science.gov (United States)

    Gong, Songjie

    Recommendation systems have become very popular in E-commerce websites. Many of the largest commerce websites are already using recommender technologies to help their customers find products to purchase. An electronic commerce recommendation system learns from a customer and recommends products that the customer will find most valuable from among the available products. But most recommendation methods are hard-wired into the system and they support only fixed recommendations. This paper presented a framework of flexible electronic commerce recommendation system. The framework is composed by user model interface, recommendation engine, recommendation strategy model, recommendation technology group, user interest model and database interface. In the recommender strategy model, the method can be collaborative filtering, content-based filtering, mining associate rules method, knowledge-based filtering method or the mixed method. The system mapped the implementation and demand through strategy model, and the whole system would be design as standard parts to adapt to the change of the recommendation strategy.

  20. Personal carbon monoxide exposures of preschool children in Helsinki, Finland - comparison to ambient air concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Alm, S.; Mukala, K.; Tittanen, P.; Jantunen, M.J. [KTL National Public Health Institute, Kuopio (Finland). Dept. of Environmental Health

    2001-07-01

    The associations of personal carbon monoxide (CO) exposures with ambient air CO concentrations measured at fixed monitoring sites, were studied among 194 children aged 3-6yr in four downtown and four suburban day-care centers in Helsinki, Finland. Each child carried a personal CO exposure monitor between 1 and 4 times for a time period of between 20 and 24h. CO concentrations at two fixed monitoring sites were measured simultaneously. The CO concentrations measured at the fixed monitoring sites were usually lower (mean maximum 8-h concentration: 0.9 and 2.6mgm{sup -3}) than the personal CO exposure concentrations (mean maximum 8-h concentration: 3.3mgm{sup -3}).The fixed site CO concentrations were poor predictors of the personal CO exposure concentrations. However, the correlations between the personal CO exposure and the fixed monitoring site CO concentrations increased (-0.03 -- -0.12 to 0.13-0.16) with increasing averaging times from 1 to 8h. Also, the fixed monitoring site CO concentrations explained the mean daily or weekly personal CO exposures of a group of simultaneously measured children better than individual exposure CO concentrations. This study suggests that the short-term CO personal exposure of children cannot be meaningfully assessed using fixed monitoring sites. (author)

  1. Zero-reabsorption doped-nanocrystal luminescent solar concentrators.

    Science.gov (United States)

    Erickson, Christian S; Bradshaw, Liam R; McDowall, Stephen; Gilbertson, John D; Gamelin, Daniel R; Patrick, David L

    2014-04-22

    Optical concentration can lower the cost of solar energy conversion by reducing photovoltaic cell area and increasing photovoltaic efficiency. Luminescent solar concentrators offer an attractive approach to combined spectral and spatial concentration of both specular and diffuse light without tracking, but they have been plagued by luminophore self-absorption losses when employed on practical size scales. Here, we introduce doped semiconductor nanocrystals as a new class of phosphors for use in luminescent solar concentrators. In proof-of-concept experiments, visibly transparent, ultraviolet-selective luminescent solar concentrators have been prepared using colloidal Mn(2+)-doped ZnSe nanocrystals that show no luminescence reabsorption. Optical quantum efficiencies of 37% are measured, yielding a maximum projected energy concentration of ∼6× and flux gain for a-Si photovoltaics of 15.6 in the large-area limit, for the first time bounded not by luminophore self-absorption but by the transparency of the waveguide itself. Future directions in the use of colloidal doped nanocrystals as robust, processable spectrum-shifting phosphors for luminescent solar concentration on the large scales required for practical application of this technology are discussed.

  2. Inaugural Maximum Values for Sodium in Processed Food Products in the Americas.

    Science.gov (United States)

    Campbell, Norm; Legowski, Barbara; Legetic, Branka; Nilson, Eduardo; L'Abbé, Mary

    2015-08-01

    Reducing dietary salt/sodium is one of the most cost-effective interventions to improve population health. There are five initiatives in the Americas that independently developed targets for reformulating foods to reduce salt/sodium content. Applying selection criteria, recommended by the Pan American Health Organization (PAHO)/World Health Organization (WHO) Technical Advisory Group on Dietary Salt/Sodium Reduction, a consortium of governments, civil society, and food companies (the Salt Smart Consortium) agreed to an inaugural set of regional maximum targets (upper limits) for salt/sodium levels for 11 food categories, to be achieved by December 2016. Ultimately, to substantively reduce dietary salt across whole populations, targets will be needed for the majority of processed and pre-prepared foods. Cardiovascular and hypertension organizations are encouraged to utilize the regional targets in advocacy and in monitoring and evaluation of progress by the food industry. © 2015 Wiley Periodicals, Inc.

  3. Complex Surface Concentration Gradients by Stenciled "Electro Click Chemistry"

    DEFF Research Database (Denmark)

    Hansen, Thomas Steen; Lind, Johan Ulrik; Daugaard, Anders Egede

    2010-01-01

    Complex one- or two-dimensional concentration gradients of alkynated molecules are produced on azidized conducting polymer substrates by stenciled "electro click chemistry". The latter describes the local electrochemical generation of catalytically active Cu(I) required to complete a "click...... reaction" between alkynes and azides at room temperature. A stencil on the counter electrode defines the shape and multiplicity of the gradient(s) on the conducting polymer substrate, while the specific reaction conditions control gradient steepness and the maximum concentration deposited. Biologically...

  4. Human mortality effects of future concentrations of tropospheric ozone

    International Nuclear Information System (INIS)

    West, J.; Szopa, S.; Hauglustaine, D.A.

    2007-01-01

    Here we explore the effects of projected future changes in global ozone concentrations on premature human mortality, under three scenarios for 2030. We use daily surface ozone concentrations from a global atmospheric transport and chemistry model, and ozone-mortality relationships from daily time-series studies. The population-weighted annual average 8-h daily maximum ozone is projected to increase, relative to the present, in each of ten world regions under the SRES A2 scenario and the current legislation (CLE) scenario, with the largest growth in tropical regions, while decreases are projected in each region in the maximum feasible reduction (MFR) scenario. Emission reductions in the CLE scenario, relative to A2, are estimated to reduce about 190,000 premature human mortalities globally in 2030, with the most avoided mortalities in Africa. The MFR scenario will avoid about 460,000 premature mortalities relative to A2 in 2030, and 270,000 relative to CLE, with the greatest reductions in South Asia. (authors)

  5. In-shoe plantar tri-axial stress profiles during maximum-effort cutting maneuvers.

    Science.gov (United States)

    Cong, Yan; Lam, Wing Kai; Cheung, Jason Tak-Man; Zhang, Ming

    2014-12-18

    Soft tissue injuries, such as anterior cruciate ligament rupture, ankle sprain and foot skin problems, frequently occur during cutting maneuvers. These injuries are often regarded as associated with abnormal joint torque and interfacial friction caused by excessive external and in-shoe shear forces. This study simultaneously investigated the dynamic in-shoe localized plantar pressure and shear stress during lateral shuffling and 45° sidestep cutting maneuvers. Tri-axial force transducers were affixed at the first and second metatarsal heads, lateral forefoot, and heel regions in the midsole of a basketball shoe. Seventeen basketball players executed both cutting maneuvers with maximum efforts. Lateral shuffling cutting had a larger mediolateral braking force than 45° sidestep cutting. This large braking force was concentrated at the first metatarsal head, as indicated by its maximum medial shear stress (312.2 ± 157.0 kPa). During propulsion phase, peak shear stress occurred at the second metatarsal head (271.3 ± 124.3 kPa). Compared with lateral shuffling cutting, 45° sidestep cutting produced larger peak propulsion shear stress (463.0 ± 272.6 kPa) but smaller peak braking shear stress (184.8 ± 181.7 kPa), of which both were found at the first metatarsal head. During both cutting maneuvers, maximum medial and posterior shear stress occurred at the first metatarsal head, whereas maximum pressure occurred at the second metatarsal head. The first and second metatarsal heads sustained relatively high pressure and shear stress and were expected to be susceptible to plantar tissue discomfort or injury. Due to different stress distribution, distinct pressure and shear cushioning mechanisms in basketball footwear might be considered over different foot regions. Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. 13 CFR 107.840 - Maximum term of Financing.

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Maximum term of Financing. 107.840... COMPANIES Financing of Small Businesses by Licensees Structuring Licensee's Financing of An Eligible Small Business: Terms and Conditions of Financing § 107.840 Maximum term of Financing. The maximum term of any...

  7. A Sentiment-Enhanced Hybrid Recommender System for Movie Recommendation: A Big Data Analytics Framework

    OpenAIRE

    Wang, Yibo; Wang, Mingming; Xu, Wei

    2018-01-01

    Movie recommendation in mobile environment is critically important for mobile users. It carries out comprehensive aggregation of user’s preferences, reviews, and emotions to help them find suitable movies conveniently. However, it requires both accuracy and timeliness. In this paper, a movie recommendation framework based on a hybrid recommendation model and sentiment analysis on Spark platform is proposed to improve the accuracy and timeliness of mobile movie recommender system. In the propo...

  8. Radon concentration in dwellings of Lanzarote (Canary Islands)

    Energy Technology Data Exchange (ETDEWEB)

    Pinza, C.; Armas, J.H. [La Laguna Univ., Tenerife (Spain). Faculty of Medicine; Poffijn, A. [Ghent Rijksuniversiteit (Belgium). Lab. voor Kernfysica

    1997-07-01

    A total of 126 radon passive dosemeters were distributed in 63 dwellings on the island of Lanzarote (Canary Islands) to measure the indoor radon concentration in the period April-June 1994. The mean overall indoor concentration was 50 Bq.m{sup -3} with a standard deviation of 17 Bq.m{sup -3}. Applying the conversion factor for the effective dose, recommended by ICRP 65, this results in a mean effective dose of 0.75 mSv.y{sup -1}. The mean radon concentration in single-family houses proves to be higher at the ground floor than in upper levels. The mean radon concentration obtained in bedrooms is higher than in living-rooms, independently of the floor they are located at. Statistically significant differences in the mean radon concentration have been found depending on the soil permeability (P = 0.001) and building materials used (P 0.0006). (author).

  9. Radon concentration in dwellings of Lanzarote (Canary Islands)

    International Nuclear Information System (INIS)

    Pinza, C.; Armas, J.H.; Poffijn, A.

    1997-01-01

    A total of 126 radon passive dosemeters were distributed in 63 dwellings on the island of Lanzarote (Canary Islands) to measure the indoor radon concentration in the period April-June 1994. The mean overall indoor concentration was 50 Bq.m -3 with a standard deviation of 17 Bq.m -3 . Applying the conversion factor for the effective dose, recommended by ICRP 65, this results in a mean effective dose of 0.75 mSv.y -1 . The mean radon concentration in single-family houses proves to be higher at the ground floor than in upper levels. The mean radon concentration obtained in bedrooms is higher than in living-rooms, independently of the floor they are located at. Statistically significant differences in the mean radon concentration have been found depending on the soil permeability (P = 0.001) and building materials used (P 0.0006). (author)

  10. 20 CFR 226.52 - Total annuity subject to maximum.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Total annuity subject to maximum. 226.52... COMPUTING EMPLOYEE, SPOUSE, AND DIVORCED SPOUSE ANNUITIES Railroad Retirement Family Maximum § 226.52 Total annuity subject to maximum. The total annuity amount which is compared to the maximum monthly amount to...

  11. Synoptic and meteorological drivers of extreme ozone concentrations over Europe

    Science.gov (United States)

    Otero, Noelia Felipe; Sillmann, Jana; Schnell, Jordan L.; Rust, Henning W.; Butler, Tim

    2016-04-01

    The present work assesses the relationship between local and synoptic meteorological conditions and surface ozone concentration over Europe in spring and summer months, during the period 1998-2012 using a new interpolated data set of observed surface ozone concentrations over the European domain. Along with local meteorological conditions, the influence of large-scale atmospheric circulation on surface ozone is addressed through a set of airflow indices computed with a novel implementation of a grid-by-grid weather type classification across Europe. Drivers of surface ozone over the full distribution of maximum daily 8-hour average values are investigated, along with drivers of the extreme high percentiles and exceedances or air quality guideline thresholds. Three different regression techniques are applied: multiple linear regression to assess the drivers of maximum daily ozone, logistic regression to assess the probability of threshold exceedances and quantile regression to estimate the meteorological influence on extreme values, as represented by the 95th percentile. The relative importance of the input parameters (predictors) is assessed by a backward stepwise regression procedure that allows the identification of the most important predictors in each model. Spatial patterns of model performance exhibit distinct variations between regions. The inclusion of the ozone persistence is particularly relevant over Southern Europe. In general, the best model performance is found over Central Europe, where the maximum temperature plays an important role as a driver of maximum daily ozone as well as its extreme values, especially during warmer months.

  12. On a predominant ionization source in the main maximum of the Venus nightside ionosphere

    International Nuclear Information System (INIS)

    Gringauz, K.I.; Verigin, M.I.; Breus, T.K.; Shvachunova, L.A.

    1983-01-01

    New considerations in favour of the previously made hypothesis, made on the basis of data using ''Venera-9 and 10'' satellites, that electron fluxes are the main ionization sources, creating the upper maximum of electron concentration in the night Venus atmosphere, are presented. Analysis of arguments, made by certain american authors, suggesting that O + ion transfer from the day Venus ionosphere to the night one should be considered as the main source of night ionization is made, and inconsistency of the argument shown

  13. Groundwater radon, radium and uranium concentrations in Regiao dos Lagos, Rio de Janeiro State, Brazil

    International Nuclear Information System (INIS)

    Almeida, R.M.R.; Lauria, D.C.; Ferreira, A.C.; Sracek, O.

    2004-01-01

    Ground water from Regiao dos Lagos, a coastal area of Rio de Janeiro state, was analysed for 226 Ra, 228 Ra, 222 Rn, 238 U, major ion concentrations, and physico-chemical parameters were also measured. Concentrations values ranged from -1 for 226 Ra, from -1 for 228 Ra and from -4 to 8.0x10 -2 Bq l -1 for 238 U. Detectable 222 Rn concentrations (>3 Bq l -1 ) were found only in two samples. The spatial distribution of Ra concentration delineated one distinct area and some hot spots with high Ra concentration. Low pH value is the most important water parameter linked to high radium concentration. This is probably related to limited adsorption of radium on soil ferric oxides and hydroxides at low pH range. There was a significant correlation between uranium concentrations and electrical conductivity values, and also between uranium concentrations and concentrations of Ca, Mg, Na, K, and Cl, indicating sea water impact. Uranium concentrations were lower than maximum contaminant level for drinking water, whereas 17 out of the 88 ground water samples had levels of radium that exceeded the maximum contaminant level for tap water. The total annual effective dose for adult due to the water consumption reaches values up to 0.8 mSv

  14. Analysis of Particulate matter (PM 10 and PM 2.5 concentration in Khorramabad city

    Directory of Open Access Journals (Sweden)

    Seyed Hamed Mirhosseini

    2013-01-01

    Full Text Available Aims: In this study, the concentration of PM10 and PM2.5 in eight station of Khorramabad city was analyzed. Materials and Methods: For this study, the data were taken from April 2010 to March 2011. The eight sampling point were chosen in account to Khorramabad maps. During this period, 240 daily PM samples including coarse particle (PM 10 and fine particle (PM 2.5 were collected. A two-part sampler was used to collect samples of PM. According to one-way ANOVA, multiple comparisons Scheffe, the obtained data were analyzed and then compared with the Environment protection organization standard rates. Khorramabad Results: The results revealed that during measuring the maximum concentration of PM 10 and PM 2.5 was respectively 120.9 and 101.09 μ/m 3 at Shamshirabad station. There was a significant difference between the mean values of PM 10 concentration (μg/m 3 in the seasons of summer. In addition, the mean concentrations of PM 10 in warmer months exceeded to the maximum permissible concentration. Conclusions: Year comparison of PM 10 and PM 2.5 concentration with standard were revealed particle matter concentration in summer season was higher than standard. Although total mean of particle matter was less than standard concentration.

  15. Optimum Er concentration for in situ doped GaN visible and infrared luminescence

    International Nuclear Information System (INIS)

    Lee, D. S.; Heikenfeld, J.; Steckl, A. J.; Hommerich, U.; Seo, J. T.; Braud, A.; Zavada, J.

    2001-01-01

    GaN thin films have been doped with varying Er concentrations (0.01--10 at.%) during molecular-beam-epitaxy growth. As expected, the visible and infrared (IR) emissions, from photoluminescence (PL) and electroluminescence (EL), are a strong function of Er concentration. We report on the determination of an optimum Er doping level for PL and EL intensity. Secondary ion mass spectroscopy and Rutherford backscattering measurements showed that the Er concentration in GaN increased exponentially with Er cell temperature. PL and EL intensity of green emission at 537 and 558 nm, due to Er 4f--4f inner shell transitions, exhibited a maximum at ∼1 at.% Er. IR PL intensity at 1.54 μm, due to another Er transition, revealed the same maximum for ∼1 at.% Er concentration. PL lifetime measurements at 537 nm showed that samples with Er concentration <1 at.% had a lifetime of ∼5 μs. For Er concentration ≥1 at.%, the lifetime decreased rapidly to values below 1 μs. This concentration quenching is believed to be due to a combination of Er cross relaxation and energy transfer to GaN defects, eventually followed by precipitation. This conclusion is supported by x-ray diffraction measurements. As a result, we have determined that the optimum Er doping concentration into GaN is ∼1 at.%. Copyright 2001 American Institute of Physics

  16. Critical analysis of the maximum non inhibitory concentration (MNIC) method in quantifying sub-lethal injury in Saccharomyces cerevisiae cells exposed to either thermal or pulsed electric field treatments.

    Science.gov (United States)

    Kethireddy, V; Oey, I; Jowett, Tim; Bremer, P

    2016-09-16

    Sub-lethal injury within a microbial population, due to processing treatments or environmental stress, is often assessed as the difference in the number of cells recovered on non-selective media compared to numbers recovered on a "selective media" containing a predetermined maximum non-inhibitory concentration (MNIC) of a selective agent. However, as knowledge of cell metabolic response to injury, population diversity and dynamics increased, the rationale behind the conventional approach of quantifying sub-lethal injury must be scrutinized further. This study reassessed the methodology used to quantify sub-lethal injury for Saccharomyces cerevisiae cells (≈ 4.75 Log CFU/mL) exposed to either a mild thermal (45°C for 0, 10 and 20min) or a mild pulsed electric field treatment (field strengths of 8.0-9.0kV/cm and energy levels of 8, 14 and 21kJ/kg). Treated cells were plated onto either Yeast Malt agar (YM) or YM containing NaCl, as a selective agent at 5-15% in 1% increments. The impact of sub-lethal stress due to initial processing, the stress due to selective agents in the plating media, and the subsequent variation of inhibition following the treatments was assessed based on the CFU count (cell numbers). ANOVA and a generalised least squares model indicated significant effects of media, treatments, and their interaction effects (P<0.05) on cell numbers. It was shown that the concentration of the selective agent used dictated the extent of sub-lethal injury recorded owing to the interaction effects of the selective component (NaCl) in the recovery media. Our findings highlight a potential common misunderstanding on how culture conditions impact on sub-lethal injury. Interestingly for S. cerevisiae cells the number of cells recovered at different NaCl concentrations in the media appears to provide valuable information about the mode of injury, the comparative efficacy of different processing regimes and the inherent degree of resistance within a population. This

  17. Influence of time of concentration on variation of runoff from a small urbanized watershed

    Science.gov (United States)

    Devendra Amatya; Agnieszka Cupak; Andrzej Walega

    2015-01-01

    The main objective of the paper is to estimate the influence of time of concentration (TC) on maximum flow in an urbanized watershed. The calculations of maximum flow have been carried out using the Rational method, Technical Release 55 (TR55) procedure based on NRCS (National Resources Conservation Services) guidelines, and NRCS-UH rainfall-runoff model. Similarly,...

  18. Future changes over the Himalayas: Maximum and minimum temperature

    Science.gov (United States)

    Dimri, A. P.; Kumar, D.; Choudhary, A.; Maharana, P.

    2018-03-01

    An assessment of the projection of minimum and maximum air temperature over the Indian Himalayan region (IHR) from the COordinated Regional Climate Downscaling EXperiment- South Asia (hereafter, CORDEX-SA) regional climate model (RCM) experiments have been carried out under two different Representative Concentration Pathway (RCP) scenarios. The major aim of this study is to assess the probable future changes in the minimum and maximum climatology and its long-term trend under different RCPs along with the elevation dependent warming over the IHR. A number of statistical analysis such as changes in mean climatology, long-term spatial trend and probability distribution function are carried out to detect the signals of changes in climate. The study also tries to quantify the uncertainties associated with different model experiments and their ensemble in space, time and for different seasons. The model experiments and their ensemble show prominent cold bias over Himalayas for present climate. However, statistically significant higher warming rate (0.23-0.52 °C/decade) for both minimum and maximum air temperature (Tmin and Tmax) is observed for all the seasons under both RCPs. The rate of warming intensifies with the increase in the radiative forcing under a range of greenhouse gas scenarios starting from RCP4.5 to RCP8.5. In addition to this, a wide range of spatial variability and disagreements in the magnitude of trend between different models describes the uncertainty associated with the model projections and scenarios. The projected rate of increase of Tmin may destabilize the snow formation at the higher altitudes in the northern and western parts of Himalayan region, while rising trend of Tmax over southern flank may effectively melt more snow cover. Such combined effect of rising trend of Tmin and Tmax may pose a potential threat to the glacial deposits. The overall trend of Diurnal temperature range (DTR) portrays increasing trend across entire area with

  19. Short communication: concentrations of nonesterified fatty acids and β-hydroxybutyrate in dairy cows are not well correlated during the transition period.

    Science.gov (United States)

    McCarthy, M M; Mann, S; Nydam, D V; Overton, T R; McArt, J A A

    2015-09-01

    The objective was to use longitudinal data of blood nonesterified fatty acids (NEFA) and β-hydroxybutyrate (BHBA) concentrations to describe the relationship between NEFA and BHBA in dairy cows during the periparturient period. Blood NEFA and BHBA concentration data collected from d 21 prepartum to 21 postpartum for 269 multiparous Holstein cows were selected from 4 different studies carried out within our research groups. Overall, NEFA concentrations were increased beginning near parturition with a relatively steady elevation of NEFA through d 9, after which concentrations gradually decreased. Prepartum BHBA concentrations began to increase beginning several days before parturition, continued to increase during the first week after parturition, and remained elevated through d 21 postpartum. Of the 269 cows included in the data set, 117 cows (43.5%) had at least one postpartum hyperketonemic event (BHBA ≥1.2mmol/L), and 202 cows (75.1%) had at least one event of elevated postpartum NEFA concentrations (≥0.70mmol/L) between 3 and 21 d in milk. Area under the curve (AUC) was used to investigate relationships between metabolites over time. Overall, the correlations between transition period NEFA and BHBA AUC were weak. We detected a negative correlation between prepartum BHBA AUC and postpartum NEFA AUC (r=-0.26). A positive correlation existed between postpartum NEFA AUC and postpartum BHBA AUC; however, the correlation coefficient was low (r=0.26). Large variation was found between the day of maximum NEFA concentration within the first 21 d in milk and day of maximum BHBA concentration for the same period. The mean and median times of maximum NEFA concentration were 6.8 and 6 d, respectively, whereas the mean and median times of maximum BHBA were 9.6 and 8 d, respectively; however, the range in days for both the mean and median day of maximum concentrations was very large. Overall, our data set indicates a weak relationship between blood concentrations of NEFA

  20. CORRELATION BETWEEN PATHOLOGY AND EXCESS OF MAXIMUM CONCENTRATION LIMIT OF POLLUTANTS IN THE ENVIRONMENT OF THE REPUBLIC OF DAGESTAN

    Directory of Open Access Journals (Sweden)

    G. M. Abdurakhmanov

    2013-01-01

    Full Text Available Abstract. Statistical data from "Indicators of health status of the Republic of Dagestan" for 1999 - 2010 years are presented in the work. The aim of this work was to identify a cause-effect correlation between non-communicable diseases (ischemic heart disease, neuropsychiatric disease, endemic goiter, diabetes, congenital anomalies and environmental factors in the Republic of Dagestan.Statistical data processing was carried out using the software package Statistica, Microsoft Excel. The Spearman rank correlation coefficient (ρ was used for identify of correlation between indicators of environmental quality and health of population.Moderate positive correlation is observed between the development of pathology and excess of concentrations of contaminants in drinking water sources. Direct correlations are founded between development of the studied pathologies and excess of concentrations of heavy metals and their mobile forms in soils of the region. Direct correlation is found between excess of concentrations of heavy metals in the pasture vegetation (factorial character and the morbidity of the population (effective character.

  1. Mexico City ozone concentrations as a function of readily-available meteorological parameters

    International Nuclear Information System (INIS)

    Brown, M.J.

    1994-01-01

    Daily maximum ozone concentrations measured at four sites within the Mexico City basin during the winter months are plotted as functions of different meteorological parameters that are routinely measured at surface stations. We found that ozone concentrations are most strongly correlated to the increase in daytime temperature and the maximum daytime wind speed. We also discovered that high ozone values at the sites in the southern end of the basin occur when winds come out of the northeast. In contrast, wind direction was found to be uncorrelated with high ozone values at the northern sites. From straightforward combinations of the meteorological variables, we derived some simple rules for estimating lower and upper bounds on the ozone concentration. Scatter in the data was too long to give significance to best-fit equations and statistics. Additionally, a small rawinsonde data set was used to investigate ozone's dependence on boundary-layer height and near-surface temperature gradient. Results were inconclusive, however, due to the small size of the data set

  2. Extracorporeal treatment for barbiturate poisoning: recommendations from the EXTRIP Workgroup.

    Science.gov (United States)

    Mactier, Robert; Laliberté, Martin; Mardini, Joelle; Ghannoum, Marc; Lavergne, Valery; Gosselin, Sophie; Hoffman, Robert S; Nolin, Thomas D

    2014-09-01

    The EXTRIP (Extracorporeal Treatments in Poisoning) Workgroup conducted a systematic review of barbiturate poisoning using a standardized evidence-based process to provide recommendations on the use of extracorporeal treatment (ECTR) in patients with barbiturate poisoning. The authors reviewed all articles, extracted data, summarized key findings, and proposed structured voting statements following a predetermined format. A 2-round modified Delphi method was used to reach a consensus on voting statements, and the RAND/UCLA Appropriateness Method was used to quantify disagreement. 617 articles met the search inclusion criteria. Data for 538 patients were abstracted and evaluated. Only case reports, case series, and nonrandomized observational studies were identified, yielding a low quality of evidence for all recommendations. Using established criteria, the workgroup deemed that long-acting barbiturates are dialyzable and short-acting barbiturates are moderately dialyzable. Four key recommendations were made. (1) The use of ECTR should be restricted to cases of severe long-acting barbiturate poisoning. (2) The indications for ECTR in this setting are the presence of prolonged coma, respiratory depression necessitating mechanical ventilation, shock, persistent toxicity, or increasing or persistently elevated serum barbiturate concentrations despite treatment with multiple-dose activated charcoal. (3) Intermittent hemodialysis is the preferred mode of ECTR, and multiple-dose activated charcoal treatment should be continued during ECTR. (4) Cessation of ECTR is indicated when clinical improvement is apparent. This report provides detailed descriptions of the rationale for all recommendations. In summary, patients with long-acting barbiturate poisoning should be treated with ECTR provided at least one of the specific criteria in the first recommendation is present. Copyright © 2014 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

  3. Toward Privacy-Preserving Personalized Recommendation Services

    Directory of Open Access Journals (Sweden)

    Cong Wang

    2018-02-01

    Full Text Available Recommendation systems are crucially important for the delivery of personalized services to users. With personalized recommendation services, users can enjoy a variety of targeted recommendations such as movies, books, ads, restaurants, and more. In addition, personalized recommendation services have become extremely effective revenue drivers for online business. Despite the great benefits, deploying personalized recommendation services typically requires the collection of users’ personal data for processing and analytics, which undesirably makes users susceptible to serious privacy violation issues. Therefore, it is of paramount importance to develop practical privacy-preserving techniques to maintain the intelligence of personalized recommendation services while respecting user privacy. In this paper, we provide a comprehensive survey of the literature related to personalized recommendation services with privacy protection. We present the general architecture of personalized recommendation systems, the privacy issues therein, and existing works that focus on privacy-preserving personalized recommendation services. We classify the existing works according to their underlying techniques for personalized recommendation and privacy protection, and thoroughly discuss and compare their merits and demerits, especially in terms of privacy and recommendation accuracy. We also identity some future research directions. Keywords: Privacy protection, Personalized recommendation services, Targeted delivery, Collaborative filtering, Machine learning

  4. Concentration and Competition in the Global Meat Market

    Directory of Open Access Journals (Sweden)

    Bocharova Yuliia G.

    2016-03-01

    Full Text Available The article is aimed at analyzing the condition, development specifics, concentration and competition in the global meat market. Both significance and role of meat in providing the food security has been substantiated. An analysis of the dynamics and structure (both geographical and commodity of production volumes, consumption, exports and imports of meat has been conducted. The major producers, consumers, exporters and importers of meat in the context of globalization have been identified. The country-based features, patterns of consumption and imports of meat have been characterized. On the basis of calculated five indicators of concentration (coefficient of concentration, the Herfindahl-Hirschman index, coefficient of relative concentration, dispersion of logarithms of market shares, index of the maximum share the features of competition in the global market of producers and consumers of meat have been determined.

  5. Review of pump suction reducer selection: Eccentric or concentric reducers

    OpenAIRE

    Mahaffey, R M; van Vuuren, S J

    2014-01-01

    Eccentric reducers are traditionally recommended for the pump suction reducer fitting to allow for transportation of air through the fitting to the pump. The ability of a concentric reducer to provide an improved approach flow to the pump while still allowing air to be transported through the fitting is investigated. Computational fluid dynamics (CFD) were utilised to analyse six concentric and six eccentric reducer geometries at four different inlet velocities to determine the flow velocity ...

  6. Effect of CO2 Concentration on Growth and Biochemical Composition of Newly Isolated Indigenous Microalga Scenedesmus bajacalifornicus BBKLP-07.

    Science.gov (United States)

    Patil, Lakkanagouda; Kaliwal, Basappa

    2017-05-01

    Photosynthetic mitigation of CO 2 through microalgae is gaining great importance due to its higher photosynthetic ability compared to plants, and the biomass can be commercially exploited for various applications. CO 2 fixation capability of the newly isolated freshwater microalgae Scenedesmus bajacalifornicus BBKLP-07 was investigated using a 1-l photobioreactor. The cultivation was carried at varying concentration of CO 2 ranging from 5 to 25%, and the temperature and light intensities were kept constant. A maximum CO 2 fixation rate was observed at 15% CO 2 concentration. Characteristic growth parameters such as biomass productivity, specific growth rate, and maximum biomass yield, and biochemical parameters such as carbohydrate, protein, lipid, chlorophyll, and carotenoid were determined and discussed. It was observed that the effect of CO 2 concentration on growth and biochemical composition was quite significant. The maximum biomass productivity was 0.061 ± 0.0007 g/l/day, and the rate of CO 2 fixation was 0.12 ± 0.002 g/l/day at 15% CO 2 concentration. The carbohydrate and lipid content were maximum at 25% CO 2 with 26.19 and 25.81% dry cell weight whereas protein, chlorophyll, and carotenoid contents were 32.89% dry cell weight, 25.07 μg/ml and 6.15 μg/ml respectively at 15% CO 2 concentration.

  7. A methodology for practical implementation of ICRP recommendations for optimization

    International Nuclear Information System (INIS)

    Webb, G.A.M.; Clarke, R.H.

    1979-01-01

    The system of dose limitation recommended by the Commission has been restated in its most recent recommendations with the requirements implying cost benefit analysis elevated to pride of place. The main subject of this paper is discussion of the problems involved in carrying out differential cost benefit analysis (optimization) studies. The various quantities such as Effective Dose Equivalent and Collective Effective Dose Equivalent Commitment needed to carry out these studies are discussed, their strengths and weaknesses identified and suggestions made as to how they should be used in practice. In particular the implications underlying the use of the collective quantities as the independent variable in these studies are clarified and examined. The need for the maximum realism in calculational models and parameters used in the calculation of collective quantities for optimization studies is stressed, with the corollary of conservative calculations for comparison with dose limits. The methods for calculating costs are examined, both for the plant or equipment installed to reduce doses and for the cost associated with the consequent reduction in health detriment. Some practical problems are cited in both the theory and practice of optimization. It is concluded that optimization is not yet sufficiently developed in either basic formalism or practical application. Some areas are identified where further work is needed. (author)

  8. SU-E-T-578: On Definition of Minimum and Maximum Dose for Target Volume

    Energy Technology Data Exchange (ETDEWEB)

    Gong, Y; Yu, J; Xiao, Y [Thomas Jefferson University Hospital, Philadelphia, PA (United States)

    2015-06-15

    Purpose: This study aims to investigate the impact of different minimum and maximum dose definitions in radiotherapy treatment plan quality evaluation criteria by using tumor control probability (TCP) models. Methods: Dosimetric criteria used in RTOG 1308 protocol are used in the investigation. RTOG 1308 is a phase III randomized trial comparing overall survival after photon versus proton chemoradiotherapy for inoperable stage II-IIIB NSCLC. The prescription dose for planning target volume (PTV) is 70Gy. Maximum dose (Dmax) should not exceed 84Gy and minimum dose (Dmin) should not go below 59.5Gy in order for the plan to be “per protocol” (satisfactory).A mathematical model that simulates the characteristics of PTV dose volume histogram (DVH) curve with normalized volume is built. The Dmax and Dmin are noted as percentage volumes Dη% and D(100-δ)%, with η and d ranging from 0 to 3.5. The model includes three straight line sections and goes through four points: D95%= 70Gy, Dη%= 84Gy, D(100-δ)%= 59.5 Gy, and D100%= 0Gy. For each set of η and δ, the TCP value is calculated using the inhomogeneously irradiated tumor logistic model with D50= 74.5Gy and γ50=3.52. Results: TCP varies within 0.9% with η; and δ values between 0 and 1. With η and η varies between 0 and 2, TCP change was up to 2.4%. With η and δ variations from 0 to 3.5, maximum of 8.3% TCP difference is seen. Conclusion: When defined maximum and minimum volume varied more than 2%, significant TCP variations were seen. It is recommended less than 2% volume used in definition of Dmax or Dmin for target dosimetric evaluation criteria. This project was supported by NIH grants U10CA180868, U10CA180822, U24CA180803, U24CA12014 and PA CURE Grant.

  9. SU-E-T-578: On Definition of Minimum and Maximum Dose for Target Volume

    International Nuclear Information System (INIS)

    Gong, Y; Yu, J; Xiao, Y

    2015-01-01

    Purpose: This study aims to investigate the impact of different minimum and maximum dose definitions in radiotherapy treatment plan quality evaluation criteria by using tumor control probability (TCP) models. Methods: Dosimetric criteria used in RTOG 1308 protocol are used in the investigation. RTOG 1308 is a phase III randomized trial comparing overall survival after photon versus proton chemoradiotherapy for inoperable stage II-IIIB NSCLC. The prescription dose for planning target volume (PTV) is 70Gy. Maximum dose (Dmax) should not exceed 84Gy and minimum dose (Dmin) should not go below 59.5Gy in order for the plan to be “per protocol” (satisfactory).A mathematical model that simulates the characteristics of PTV dose volume histogram (DVH) curve with normalized volume is built. The Dmax and Dmin are noted as percentage volumes Dη% and D(100-δ)%, with η and d ranging from 0 to 3.5. The model includes three straight line sections and goes through four points: D95%= 70Gy, Dη%= 84Gy, D(100-δ)%= 59.5 Gy, and D100%= 0Gy. For each set of η and δ, the TCP value is calculated using the inhomogeneously irradiated tumor logistic model with D50= 74.5Gy and γ50=3.52. Results: TCP varies within 0.9% with η; and δ values between 0 and 1. With η and η varies between 0 and 2, TCP change was up to 2.4%. With η and δ variations from 0 to 3.5, maximum of 8.3% TCP difference is seen. Conclusion: When defined maximum and minimum volume varied more than 2%, significant TCP variations were seen. It is recommended less than 2% volume used in definition of Dmax or Dmin for target dosimetric evaluation criteria. This project was supported by NIH grants U10CA180868, U10CA180822, U24CA180803, U24CA12014 and PA CURE Grant

  10. Maximum likely scale estimation

    DEFF Research Database (Denmark)

    Loog, Marco; Pedersen, Kim Steenstrup; Markussen, Bo

    2005-01-01

    A maximum likelihood local scale estimation principle is presented. An actual implementation of the estimation principle uses second order moments of multiple measurements at a fixed location in the image. These measurements consist of Gaussian derivatives possibly taken at several scales and/or ...

  11. [Studies on markers of exposure and early effect in areas with arsenic pollution: methods and results of the project SEpiAs. Epidemiological studies on population exposed to low-to-moderate arsenic concentration in drinking water].

    Science.gov (United States)

    Bustaffa, Elisa; Bianchi, Fabrizio

    2014-01-01

    Arsenic and its inorganic compounds are classified as human carcinogens. Several epidemiological studies conducted in areas of the world characterized by high arsenic concentration in drinking water, even up to 3,000 μg/l, report associations between arsenic exposure and skin, bladder, lung, liver and kidney cancer as well as cardiovascular diseases, diabetes and reproductive and developmental effects. Since general population is not exposed to these high arsenic concentrations in the last years attention focused on adverse health effects that low-to-moderate arsenic concentrations (0-150 μg/l) in drinking water could induce. The World Health Organization recommends a maximum limit of 10 μg/l for arsenic in drinking water. Almost all epidemiological studies conducted on populations exposed to low-to-moderate arsenic concentrations in drinking water are limited due to problems arising from both individual exposure assessment and low subjects number. The aim of the present review is to collect literature-based evidences regarding adverse health effects associated with exposure to low-to-moderate arsenic concentrations in drinking water (10-150 μg/l) in order to obtain a comprehensive picture of the health outcomes that such exposure can have on general population.

  12. RARD: The Related-Article Recommendation Dataset

    OpenAIRE

    Beel, Joeran; Carevic, Zeljko; Schaible, Johann; Neusch, Gabor

    2017-01-01

    Recommender-system datasets are used for recommender-system evaluations, training machine-learning algorithms, and exploring user behavior. While there are many datasets for recommender systems in the domains of movies, books, and music, there are rather few datasets from research-paper recommender systems. In this paper, we introduce RARD, the Related-Article Recommendation Dataset, from the digital library Sowiport and the recommendation-as-a-service provider Mr. DLib. The dataset contains ...

  13. Maximum gravitational redshift of white dwarfs

    International Nuclear Information System (INIS)

    Shapiro, S.L.; Teukolsky, S.A.

    1976-01-01

    The stability of uniformly rotating, cold white dwarfs is examined in the framework of the Parametrized Post-Newtonian (PPN) formalism of Will and Nordtvedt. The maximum central density and gravitational redshift of a white dwarf are determined as functions of five of the nine PPN parameters (γ, β, zeta 2 , zeta 3 , and zeta 4 ), the total angular momentum J, and the composition of the star. General relativity predicts that the maximum redshifts is 571 km s -1 for nonrotating carbon and helium dwarfs, but is lower for stars composed of heavier nuclei. Uniform rotation can increase the maximum redshift to 647 km s -1 for carbon stars (the neutronization limit) and to 893 km s -1 for helium stars (the uniform rotation limit). The redshift distribution of a larger sample of white dwarfs may help determine the composition of their cores

  14. A Systematic Method of Interconnection Optimization for Dense-Array Concentrator Photovoltaic System

    Science.gov (United States)

    Siaw, Fei-Lu

    2013-01-01

    This paper presents a new systematic approach to analyze all possible array configurations in order to determine the most optimal dense-array configuration for concentrator photovoltaic (CPV) systems. The proposed method is fast, simple, reasonably accurate, and very useful as a preliminary study before constructing a dense-array CPV panel. Using measured flux distribution data, each CPV cells' voltage and current values at three critical points which are at short-circuit, open-circuit, and maximum power point are determined. From there, an algorithm groups the cells into basic modules. The next step is I-V curve prediction, to find the maximum output power of each array configuration. As a case study, twenty different I-V predictions are made for a prototype of nonimaging planar concentrator, and the array configuration that yields the highest output power is determined. The result is then verified by assembling and testing of an actual dense-array on the prototype. It was found that the I-V curve closely resembles simulated I-V prediction, and measured maximum output power varies by only 1.34%. PMID:24453823

  15. A Systematic Method of Interconnection Optimization for Dense-Array Concentrator Photovoltaic System

    Directory of Open Access Journals (Sweden)

    Fei-Lu Siaw

    2013-01-01

    Full Text Available This paper presents a new systematic approach to analyze all possible array configurations in order to determine the most optimal dense-array configuration for concentrator photovoltaic (CPV systems. The proposed method is fast, simple, reasonably accurate, and very useful as a preliminary study before constructing a dense-array CPV panel. Using measured flux distribution data, each CPV cells’ voltage and current values at three critical points which are at short-circuit, open-circuit, and maximum power point are determined. From there, an algorithm groups the cells into basic modules. The next step is I-V curve prediction, to find the maximum output power of each array configuration. As a case study, twenty different I-V predictions are made for a prototype of nonimaging planar concentrator, and the array configuration that yields the highest output power is determined. The result is then verified by assembling and testing of an actual dense-array on the prototype. It was found that the I-V curve closely resembles simulated I-V prediction, and measured maximum output power varies by only 1.34%.

  16. A systematic method of interconnection optimization for dense-array concentrator photovoltaic system.

    Science.gov (United States)

    Siaw, Fei-Lu; Chong, Kok-Keong

    2013-01-01

    This paper presents a new systematic approach to analyze all possible array configurations in order to determine the most optimal dense-array configuration for concentrator photovoltaic (CPV) systems. The proposed method is fast, simple, reasonably accurate, and very useful as a preliminary study before constructing a dense-array CPV panel. Using measured flux distribution data, each CPV cells' voltage and current values at three critical points which are at short-circuit, open-circuit, and maximum power point are determined. From there, an algorithm groups the cells into basic modules. The next step is I-V curve prediction, to find the maximum output power of each array configuration. As a case study, twenty different I-V predictions are made for a prototype of nonimaging planar concentrator, and the array configuration that yields the highest output power is determined. The result is then verified by assembling and testing of an actual dense-array on the prototype. It was found that the I-V curve closely resembles simulated I-V prediction, and measured maximum output power varies by only 1.34%.

  17. The optimal atmospheric CO2 concentration for the growth of winter wheat (Triticum aestivum).

    Science.gov (United States)

    Xu, Ming

    2015-07-20

    This study examined the optimal atmospheric CO2 concentration of the CO2 fertilization effect on the growth of winter wheat with growth chambers where the CO2 concentration was controlled at 400, 600, 800, 1000, and 1200 ppm respectively. I found that initial increase in atmospheric CO2 concentration dramatically enhanced winter wheat growth through the CO2 fertilization effect. However, this CO2 fertilization effect was substantially compromised with further increase in CO2 concentration, demonstrating an optimal CO2 concentration of 889.6, 909.4, and 894.2 ppm for aboveground, belowground, and total biomass, respectively, and 967.8 ppm for leaf photosynthesis. Also, high CO2 concentrations exceeding the optima not only reduced leaf stomatal density, length and conductance, but also changed the spatial distribution pattern of stomata on leaves. In addition, high CO2 concentration also decreased the maximum carboxylation rate (Vc(max)) and the maximum electron transport rate (J(max)) of leaf photosynthesis. However, the high CO2 concentration had little effect on leaf length and plant height. The optimal CO2 fertilization effect found in this study can be used as an indicator in selecting and breeding new wheat strains in adapting to future high atmospheric CO2 concentrations and climate change. Copyright © 2015. Published by Elsevier GmbH.

  18. Heavy metals concentration in various tissues of two freshwater ...

    African Journals Online (AJOL)

    Heavy metals like cadmium, zinc, copper, chromium, lead and mercury were measured in the various tissues of Labeo rohita and Channa striatus and in the water samples collected from ... The values of heavy metals concentration in the present study are within the maximum permissible levels for drinking water and fish.

  19. Revealing the Maximum Strength in Nanotwinned Copper

    DEFF Research Database (Denmark)

    Lu, L.; Chen, X.; Huang, Xiaoxu

    2009-01-01

    boundary–related processes. We investigated the maximum strength of nanotwinned copper samples with different twin thicknesses. We found that the strength increases with decreasing twin thickness, reaching a maximum at 15 nanometers, followed by a softening at smaller values that is accompanied by enhanced...

  20. 49 CFR 195.406 - Maximum operating pressure.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Maximum operating pressure. 195.406 Section 195.406 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS... HAZARDOUS LIQUIDS BY PIPELINE Operation and Maintenance § 195.406 Maximum operating pressure. (a) Except for...

  1. Heavy metal accumulation in arctic hares (Lepus arcticus) in Nunavut, Canada

    Energy Technology Data Exchange (ETDEWEB)

    Pedersen, Simen [Department of Biology, University of Tromso, N-9037 Tromso (Norway)]. E-mail: simenpeders1@gmail.com; Lierhagen, Syverin [Norwegian Institute for Nature Research, Tungasletta 2, N-7485 Trondheim (Norway)

    2006-09-15

    Accumulation of cadmium, mercury, lead, copper and zinc was studied in muscle, liver and kidney of 9 adult and 7 juvenile arctic hares (Lepus arcticus), collected in 2003 in the southwestern part of Nunavut, Canada. Our objective was to determine the level of heavy metal accumulation, and distribution among age groups and tissue. Concentrations of all metals varied among tissues, and concentrations of Cd, Hg and Zn were higher in adults compared to juveniles. We found correlations in metal content among tissues, and among metals in kidneys. We also found the hares to have low concentration of most heavy metals except cadmium. We suggest that the high cadmium levels might be caused by the local geology, and the hares being adapted to these levels. The low levels of the other metals are probably due to low input of atmospheric contaminants. Only one of the individuals had Cd content slightly above the maximum contaminant levels recommended for human consumption of meat. There were no levels in meat above the recommended maximum for the rest of the metals surveyed. However the Cd levels in liver and kidney are orders of magnitude higher than the recommended maximum, and consumption of these organs should be avoided.

  2. Fiber Bragg Grating Sensor for Detection of Nitrate Concentration in Water

    Directory of Open Access Journals (Sweden)

    A. S. LALASANGI

    2011-02-01

    Full Text Available The concentrations of chemical species in drinking water are of great interest. We demonstrated etched fiber Bragg grating (FBG as a concentration sensor for nitrate by analyzing the Bragg wavelength shift with concentration of chemical solution. The FBG is fabricated by phase mask technique on single mode Ge-B co-doped photosensitive fiber. Sensitivity of FBGs to the surrounding solution concentration can be enhanced by reducing diameter of the cladding with 40 % HF solution. The maximum sensitivity achieved is 1.322 ´ 10-3 nm/ppm. The overall shift of Bragg wavelength is of the order of 6.611 ´ 10-2 nm for 10 to 50 ppm concentration.

  3. Forecasts of methane concentration at the outlet of the longwall with caving area - case study

    Science.gov (United States)

    Badura, Henryk; Bańka, Piotr; Musioł, Dariusz; Wesołowski, Marek

    2017-11-01

    This paper presents the characteristics of methane hazard and prevention undertaken in the N-6 longwall of seam 330/2 in “Krupiński" coal mine. On the basis of methane concentration measurements conducted with the use of telemetric system, time series of the average and maximum methane concentration at the outlet of the longwall area were generated. It was ascertained that they exhibit a strong autocorrelation. Based on a series of the average methane concentration, a time series of ventilation methane content was created and a total methane content was calculated with the use of methane flow rate measurements in the demethanization system. It was ascertained that dependence between methane concentration and output on the examined day and on the previous day is weak and also that the dependence between methane concentration and air flow rate is very weak. Dependencies between ventilation methane content, total methane content and demethanization efficiency were also investigated. Based on forecasting models [1] developed earlier by H. Badura, forecasts have been made to predict the average and maximum methane concentrations. The measured values f methane concentration show a high level of accordance with forecasted ones.

  4. Leaf Dynamics of Panicum maximum under Future Climatic Changes.

    Science.gov (United States)

    Britto de Assis Prado, Carlos Henrique; Haik Guedes de Camargo-Bortolin, Lívia; Castro, Érique; Martinez, Carlos Alberto

    2016-01-01

    Panicum maximum Jacq. 'Mombaça' (C4) was grown in field conditions with sufficient water and nutrients to examine the effects of warming and elevated CO2 concentrations during the winter. Plants were exposed to either the ambient temperature and regular atmospheric CO2 (Control); elevated CO2 (600 ppm, eC); canopy warming (+2°C above regular canopy temperature, eT); or elevated CO2 and canopy warming (eC+eT). The temperatures and CO2 in the field were controlled by temperature free-air controlled enhancement (T-FACE) and mini free-air CO2 enrichment (miniFACE) facilities. The most green, expanding, and expanded leaves and the highest leaf appearance rate (LAR, leaves day(-1)) and leaf elongation rate (LER, cm day(-1)) were observed under eT. Leaf area and leaf biomass were higher in the eT and eC+eT treatments. The higher LER and LAR without significant differences in the number of senescent leaves could explain why tillers had higher foliage area and leaf biomass in the eT treatment. The eC treatment had the lowest LER and the fewest expanded and green leaves, similar to Control. The inhibitory effect of eC on foliage development in winter was indicated by the fewer green, expanded, and expanding leaves under eC+eT than eT. The stimulatory and inhibitory effects of the eT and eC treatments, respectively, on foliage raised and lowered, respectively, the foliar nitrogen concentration. The inhibition of foliage by eC was confirmed by the eC treatment having the lowest leaf/stem biomass ratio and by the change in leaf biomass-area relationships from linear or exponential growth to rectangular hyperbolic growth under eC. Besides, eC+eT had a synergist effect, speeding up leaf maturation. Therefore, with sufficient water and nutrients in winter, the inhibitory effect of elevated CO2 on foliage could be partially offset by elevated temperatures and relatively high P. maximum foliage production could be achieved under future climatic change.

  5. Impacts of climate change on the trends of extreme rainfall indices and values of maximum precipitation at Olimpiyat Station, Istanbul, Turkey

    Science.gov (United States)

    Nigussie, Tewodros Assefa; Altunkaynak, Abdusselam

    2018-03-01

    In this study, extreme rainfall indices of Olimpiyat Station were determined from reference period (1971-2000) and future period (2070-2099) daily rainfall data projected using the HadGEM2-ES and GFDL-ESM2M global circulation models (GCMs) and downscaled by the RegCM4.3.4 regional model under the Representative Concentration Pathway RCP4.5 and RCP8.5 scenarios. The Mann-Kendall (MK) trend statistics was used to detect trends in the indices of each group, and the nonparametric Wilcoxon signed ranks test was employed to identify the presence of differences among the values of the rainfall indices of the three groups. Moreover, the peaks-over-threshold (POT) method was used to undertake frequency analysis and estimate the maximum 24-h rainfall values of various return periods. The results of the M-K-based trend analyses showed that there are insignificant increasing trends in most of the extreme rainfall indices. However, based on the Wilcoxon signed ranks test, the values of the extreme rainfall indices determined for the future period, particularly under RCP8.5, were found to be significantly different from the corresponding values determined for the reference period. The maximum 24-h rainfall amounts of the 50-year return period of the future period under RCP4.5 of the HadGEM2-ES and GFDL-ESM2M GCMs were found to be larger (by 5.85%) than the corresponding value of the reference period by 5.85 and 21.43%, respectively. The results also showed that the maximum 24-h rainfall amount under RCP8.5 of both the HadGEM2-ES and GFDL-ESM2M GCMs was found to be greater (34.33 and 12.18%, respectively, for the 50-year return period) than the reference period values. This may increase the risk of flooding in Ayamama Watershed, and thus, studying the effects of the predicted amount of rainfall under the RCP8.5 scenario on the flooding risk of Ayamama Watershed and devising management strategies are recommended to enhance the design and implementation of adaptation measures.

  6. Receiving recommendations and providing feedback : the user-experience of a recommender system

    NARCIS (Netherlands)

    Knijnenburg, B.P.; Willemsen, M.C.; Hirtbach, S.; Buccafurri, F.; Semeraro, G.

    2010-01-01

    This paper systematically evaluates the user experience of a recommender system. Using both behavioral data and subjective measures of user experience, we demonstrate that choice satisfaction and system effectiveness increase when a system provides personalized recommendations (compared to the same

  7. Paddle River Dam : review of probable maximum flood

    Energy Technology Data Exchange (ETDEWEB)

    Clark, D. [UMA Engineering Ltd., Edmonton, AB (Canada); Neill, C.R. [Northwest Hydraulic Consultants Ltd., Edmonton, AB (Canada)

    2008-07-01

    The Paddle River Dam was built in northern Alberta in the mid 1980s for flood control. According to the 1999 Canadian Dam Association (CDA) guidelines, this 35 metre high, zoned earthfill dam with a spillway capacity sized to accommodate a probable maximum flood (PMF) is rated as a very high hazard. At the time of design, it was estimated to have a peak flow rate of 858 centimetres. A review of the PMF in 2002 increased the peak flow rate to 1,890 centimetres. In light of a 2007 revision of the CDA safety guidelines, the PMF was reviewed and the inflow design flood (IDF) was re-evaluated. This paper discussed the levels of uncertainty inherent in PMF determinations and some difficulties encountered with the SSARR hydrologic model and the HEC-RAS hydraulic model in unsteady mode. The paper also presented and discussed the analysis used to determine incremental damages, upon which a new IDF of 840 m{sup 3}/s was recommended. The paper discussed the PMF review, modelling methodology, hydrograph inputs, and incremental damage of floods. It was concluded that the PMF review, involving hydraulic routing through the valley bottom together with reconsideration of the previous runoff modeling provides evidence that the peak reservoir inflow could reasonably be reduced by approximately 20 per cent. 8 refs., 5 tabs., 8 figs.

  8. An Idea on the Maximum Permissible Concentrations of Radioactive Materials in Sea Water; Concentrations Maxima Admissibles des Substances Radioactives dans l'Eau de Mer; 041e 041c 0414 ; Concentracion Maxima Admisible de Materiales Radiactivos en las Aguas del Mar

    Energy Technology Data Exchange (ETDEWEB)

    Hiyama, Yoshio [University of Tokyo (Japan)

    1960-07-01

    The author of the present paper has tried to find a relationship between the level of sea-water contamination by several radionuclides and the level of the radiation dose-rate inside the human body caused by these radionuclides of marine origin, using the ICRP recommendation and the few data on the chemical analysis of sea water and of the human body at present available to the author. However, even if the idea of this calculation were to be recognized by scientists in the fields of oceanography, public health, nutrition, radiation biology, and others, it would still be necessary to get further data on the amounts of trace elements in sea-water, in marine products, and in the human body in order to complete a table of the maximum permissible concentrations in sea-water of various radionuclides. Here the idea is merely advanced and a few examples are described. (author) [French] L'auteur a cherche a etablir un rapport entre le degre de contamination de l'eau de mer par plusieurs radionuclides et le degre d'irradiation de l'interieur du corps humain due a ces radionuclides d'origine marine; a cet effet, il s'est fonde sur les recommandations de la CIPR et sur les quelques donnees relatives a l'analyse chimique de l'eau de mer et du corps humain qu'il avait a sa disposition. Cependant, meme si le principe de ce calcul etait reconnu par les oceanographes, les hygienistes, les bromatologistes, les radiobiologistes et d'autres specialistes, il n'en serait pas moins necessaire d'obtenir des renseignements supplementaires sur les quantites d'oligoelements existant dans l'eau de mer, les produits de la mer et le corps humain, en vue de dresser un tableau complet des concentrations maxima admissibles de divers radionuclides dans l'eau de mer. L'auteur se borne a formuler le concept et a donner quelques exemples. (author) [Spanish] El autor, teniendo en cuenta la recomendacion de la Comision Internacional de Proteccion Radiologica y los pocos datos de que actualmente dispone

  9. Maximum spectral demands in the near-fault region

    Science.gov (United States)

    Huang, Yin-Nan; Whittaker, Andrew S.; Luco, Nicolas

    2008-01-01

    The Next Generation Attenuation (NGA) relationships for shallow crustal earthquakes in the western United States predict a rotated geometric mean of horizontal spectral demand, termed GMRotI50, and not maximum spectral demand. Differences between strike-normal, strike-parallel, geometric-mean, and maximum spectral demands in the near-fault region are investigated using 147 pairs of records selected from the NGA strong motion database. The selected records are for earthquakes with moment magnitude greater than 6.5 and for closest site-to-fault distance less than 15 km. Ratios of maximum spectral demand to NGA-predicted GMRotI50 for each pair of ground motions are presented. The ratio shows a clear dependence on period and the Somerville directivity parameters. Maximum demands can substantially exceed NGA-predicted GMRotI50 demands in the near-fault region, which has significant implications for seismic design, seismic performance assessment, and the next-generation seismic design maps. Strike-normal spectral demands are a significantly unconservative surrogate for maximum spectral demands for closest distance greater than 3 to 5 km. Scale factors that transform NGA-predicted GMRotI50 to a maximum spectral demand in the near-fault region are proposed.

  10. Gas Hydrate and Free Gas Concentrations in Two Sites inside the Chilean Margin (Itata and Valdivia Offshores

    Directory of Open Access Journals (Sweden)

    Vargas-Cordero Iván

    2017-12-01

    Full Text Available Two sectors, Itata and Valdivia, which are located in the Chilean margin were analysed by using seismic data with the main purpose to characterize the gas hydrate concentration. Strong lateral velocity variations are recognised, showing a maximum value in Valdivia offshore (2380 ms−1 above the BSR and a minimum value in the Itata offshore (1380 m·s−1 below the BSR. In both of the sectors, the maximum hydrate concentration reaches 17% of total volume, while the maximum free gas concentration is located Valdivia offshore (0.6% of total volume in correspondence of an uplift sector. In the Itata offshore, the geothermal gradient that is estimated is variable and ranges from 32 °C·km−1 to 87 °C·km−1, while in Valdivia offshore it is uniform and about 35 °C·km−1. When considering both sites, the highest hydrate concentration is located in the accretionary prism (Valdivia offshore and highest free gas concentration is distributed upwards, which may be considered as a natural pathway for lateral fluid migration. The results that are presented here contribute to the global knowledge of the relationship between hydrate/free gas presence and tectonic features, such as faults and folds, and furnishes a piece of the regional hydrate potentiality Chile offshore.

  11. Recommendation systems in software engineering

    CERN Document Server

    Robillard, Martin P; Walker, Robert J; Zimmermann, Thomas

    2014-01-01

    With the growth of public and private data stores and the emergence of off-the-shelf data-mining technology, recommendation systems have emerged that specifically address the unique challenges of navigating and interpreting software engineering data.This book collects, structures and formalizes knowledge on recommendation systems in software engineering. It adopts a pragmatic approach with an explicit focus on system design, implementation, and evaluation. The book is divided into three parts: "Part I - Techniques" introduces basics for building recommenders in software engineering, including techniques for collecting and processing software engineering data, but also for presenting recommendations to users as part of their workflow.?"Part II - Evaluation" summarizes methods and experimental designs for evaluating recommendations in software engineering.?"Part III - Applications" describes needs, issues and solution concepts involved in entire recommendation systems for specific software engineering tasks, fo...

  12. Concentrations of Mercury, Lead, Chromium, Cadmium, Arsenic and Aluminum in Irrigation Water Wells and Wastewaters Used for Agriculture in Mashhad, Northeastern Iran

    Directory of Open Access Journals (Sweden)

    SR Mousavi

    2013-04-01

    Full Text Available Background: Contamination of water by toxic chemicals has become commonly recognized as an environmental concern. Based on our clinical observation in Mashhad, northeastern Iran, many people might be at risk of exposure to high concentrations of toxic heavy metals in water. Because wastewater effluents as well as water wells have been commonly used for irrigation over the past decades, there has been some concern on the toxic metal exposure of crops and vegetables irrigated with the contaminated water. Objective: To measure the concentrations of mercury, lead, chromium, cadmium, arsenic and aluminium in irrigation water wells and wastewaters used for agriculture in Mashhad, northeastern Iran. Methods: 36 samples were taken from irrigation water wells and a wastewater refinery in North of Mashhad at four times—May 2008, March 2009, and June and July 2010. Atomic absorption spectrometry was used to measure the concentration of toxic metals. Graphite furnace was used for the measurement of lead, chromium, cadmium and aluminum. Mercury and arsenic concentrations were measured by mercury/hydride system. Results: Chromium, cadmium, lead and arsenic concentrations in the samples were within the standard range. The mean±SD concentration of mercury in irrigation wells (1.02±0.40 μg/L exceeded the FAO maximum permissible levels. The aluminum concentration in irrigation water varied significantly from month to month (p=0.03. All wastewater samples contained high mercury concentrations (6.64±2.53 μg/L. Conclusion: For high mercury and aluminum concentrations, the water sources studied should not be used for agricultural use. Regular monitoring of the level of heavy metals in water and employing the necessary environmental interventions in this area are strongly recommended.

  13. Seasonal Variation in Human Salivary Cortisol Concentration

    DEFF Research Database (Denmark)

    Persson, Roger; Garde, Anne Helene; Hansen, Åse Marie

    2008-01-01

    Measurement of cortisol concentration can contribute important information about an individual's ability to adjust to various environmental demands of both physical and psychosocial origin. However, one uncertainty that affects the possibilities of correctly interpreting and designing field studies...... is the lack of observations of the impact of seasonal changes on cortisol excretion. For this reason, the month-to-month changes in diurnal cortisol concentration, the awakening cortisol response (ACR), maximum morning concentration, and fall during the day were studied in a group of 24 healthy men and women...... 32 to 61 yrs of age engaged in active work. On one workday for 12 consecutive months, participants collected saliva at four time points for determination of cortisol: at awakening, +30 min, +8 h, and at 21:00 h. Data were analyzed by a repeated measures design with month (12 levels) and time...

  14. Application of maximum values for radiation exposure and principles for the calculation of radiation doses

    International Nuclear Information System (INIS)

    2007-08-01

    The guide presents the definitions of equivalent dose and effective dose, the principles for calculating these doses, and instructions for applying their maximum values. The limits (Annual Limit on Intake and Derived Air Concentration) derived from dose limits are also presented for the purpose of monitoring exposure to internal radiation. The calculation of radiation doses caused to a patient from medical research and treatment involving exposure to ionizing radiation is beyond the scope of this ST Guide

  15. A consistent high primary production and chlorophyll-a maximum in a narrow strait – effects of hydraulic control

    DEFF Research Database (Denmark)

    Lund-Hansen, Lars Chresten; Nielsen, Morten Holtegaard; Bruhn, Annette

    2008-01-01

    and the North Sea. The time-series were supplemented with Scan Fish transects — a towed CTD, ADCP measurements, and nutrient data. There is a significant maximum in primary production (mg C m− 2 day− 1) in central LB, which is 30% higher than outside the LB region. Chl-a concentrations are 30% higher in central...

  16. Maximum allowable load on wheeled mobile manipulators

    International Nuclear Information System (INIS)

    Habibnejad Korayem, M.; Ghariblu, H.

    2003-01-01

    This paper develops a computational technique for finding the maximum allowable load of mobile manipulator during a given trajectory. The maximum allowable loads which can be achieved by a mobile manipulator during a given trajectory are limited by the number of factors; probably the dynamic properties of mobile base and mounted manipulator, their actuator limitations and additional constraints applied to resolving the redundancy are the most important factors. To resolve extra D.O.F introduced by the base mobility, additional constraint functions are proposed directly in the task space of mobile manipulator. Finally, in two numerical examples involving a two-link planar manipulator mounted on a differentially driven mobile base, application of the method to determining maximum allowable load is verified. The simulation results demonstrates the maximum allowable load on a desired trajectory has not a unique value and directly depends on the additional constraint functions which applies to resolve the motion redundancy

  17. Coefficient of friction and wear rate effects of different composite nanolubricant concentrations on Aluminium 2024 plate

    Science.gov (United States)

    Zawawi, N. N. M.; Azmi, W. H.; Redhwan, A. A. M.; Sharif, M. Z.

    2017-10-01

    Wear of sliding parts and operational machine consistency enhancement can be avoided with good lubrication. Lubrication reduce wear between two contacting and sliding surfaces and decrease the frictional power losses in compressor. The coefficient of friction and wear rate effects study were carried out to measure the friction and anti-wear abilities of Al2O3-SiO2 composite nanolubricants a new type of compressor lubricant to enhanced the compressor performances. The tribology test rig employing reciprocating test conditions to replicate a piston ring contact in the compressor was used to measure the coefficient of friction and wear rate. Coefficient of friction and wear rate effects of different Al2O3-SiO2/PAG composite nanolubricants of Aluminium 2024 plate for 10-kg load at different speed were investigated. Al2O3 and SiO2 nanoparticles were dispersed in the Polyalkylene Glycol (PAG 46) lubricant using two-steps method of preparation. The result shows that the coefficient friction and wear rate of composite nanolubricants decreased compared to pure lubricant. The maximum reduction achievement for friction of coefficient and wear rate by Al2O3-SiO2 composite nanolubricants by 4.78% and 12.96% with 0.06% volume concentration. Therefore, 0.06% volume concentration is selected as the most enhanced composite nanolubricants with effective coefficient of friction and wear rate reduction compared to other volume concentrations. Thus, it is recommended to be used as the compressor lubrication to enhanced compressor performances.

  18. Statement and recommendations of the International Commission on Radiological Protection from its 1980 meeting

    International Nuclear Information System (INIS)

    1980-01-01

    A short report of the 1980 annual meeting of the ICRP is given along with the recommendations proposed. These are as follows: 1) for the lens of the eye, the annual dose-equivalent limit should be reduced from 0.3Sv to 0.15 Sv, 2) the recommended annual limit for intake by inhalation for radon-222 daughters is 0.02 J and corresponds to an air concentration of 0.4 working levels in previous practical units, 3) the recent information on estimate of radiation risk does not call for changes in the risk factors for stochastic effects or the dose-effect relationships for non-stochastic effects underlying the dose-equivalent limits recommended in ICRP publication 26. The assessment of the total detriment by summation using weighting factors for different organs is also discussed. (U.K.)

  19. Robust Maximum Association Estimators

    NARCIS (Netherlands)

    A. Alfons (Andreas); C. Croux (Christophe); P. Filzmoser (Peter)

    2017-01-01

    textabstractThe maximum association between two multivariate variables X and Y is defined as the maximal value that a bivariate association measure between one-dimensional projections αX and αY can attain. Taking the Pearson correlation as projection index results in the first canonical correlation

  20. Measurements of radon concentration levels in drinking water at urban area of Curitiba, Brazil

    International Nuclear Information System (INIS)

    Correa, Janine Nicolosi; Paschuk, Sergei A.; Schelin, Hugo R.; Barbosa, Laercio; Sadula, Tatyana; Matsuzaki, Cristiana A.

    2009-01-01

    Current work presents the results of more than 100 measurements of 222 Rn activity in drinking water collected at artesian bores at Curitiba region during the period of 2008 - 2009. The measurements were performed at the Laboratory of Applied Nuclear Physics of the Federal University of Technology in cooperation with the Nuclear Technology Development Center (CDTN) of Brazilian Nuclear Energy Committee (CNEN). Experimental setup was based on the Professional Radon Monitor (ALPHA GUARD) connected to specific kit of glass vessels Aqua KIT through the air pump. The equipment was adjusted with air flow of 0.5 L/min. The 222 Rn concentration levels were detected and analyzed by the computer every 10 minutes using the software DataEXPERT by GENITRON Instruments. Collected average levels of 222 Rn concentration were processed taking into account the volume of water sample and its temperature, atmospheric pressure and the total volume of the air in the vessels. Collected samples of water presented the average 222 Rn activity about 57.70 Bq/L which is almost 5 times more than maximum level of 11.1 Bq/L recommended by the USEPA (United States Environmental Protection Agency). It has to be noted that many artesian drillings presented the radon activity in the range of 100 - 200 Bq/L. Further measurements are planned to be performed at other regions of Parana State and will involve the mineral water sources, explored artesian drillings as well as soil samples. (author)''

  1. Selection of the Maximum Spatial Cluster Size of the Spatial Scan Statistic by Using the Maximum Clustering Set-Proportion Statistic.

    Science.gov (United States)

    Ma, Yue; Yin, Fei; Zhang, Tao; Zhou, Xiaohua Andrew; Li, Xiaosong

    2016-01-01

    Spatial scan statistics are widely used in various fields. The performance of these statistics is influenced by parameters, such as maximum spatial cluster size, and can be improved by parameter selection using performance measures. Current performance measures are based on the presence of clusters and are thus inapplicable to data sets without known clusters. In this work, we propose a novel overall performance measure called maximum clustering set-proportion (MCS-P), which is based on the likelihood of the union of detected clusters and the applied dataset. MCS-P was compared with existing performance measures in a simulation study to select the maximum spatial cluster size. Results of other performance measures, such as sensitivity and misclassification, suggest that the spatial scan statistic achieves accurate results in most scenarios with the maximum spatial cluster sizes selected using MCS-P. Given that previously known clusters are not required in the proposed strategy, selection of the optimal maximum cluster size with MCS-P can improve the performance of the scan statistic in applications without identified clusters.

  2. Maximum-Likelihood Detection Of Noncoherent CPM

    Science.gov (United States)

    Divsalar, Dariush; Simon, Marvin K.

    1993-01-01

    Simplified detectors proposed for use in maximum-likelihood-sequence detection of symbols in alphabet of size M transmitted by uncoded, full-response continuous phase modulation over radio channel with additive white Gaussian noise. Structures of receivers derived from particular interpretation of maximum-likelihood metrics. Receivers include front ends, structures of which depends only on M, analogous to those in receivers of coherent CPM. Parts of receivers following front ends have structures, complexity of which would depend on N.

  3. TRENDS IN ESTIMATED MIXING DEPTH DAILY MAXIMUMS

    Energy Technology Data Exchange (ETDEWEB)

    Buckley, R; Amy DuPont, A; Robert Kurzeja, R; Matt Parker, M

    2007-11-12

    Mixing depth is an important quantity in the determination of air pollution concentrations. Fireweather forecasts depend strongly on estimates of the mixing depth as a means of determining the altitude and dilution (ventilation rates) of smoke plumes. The Savannah River United States Forest Service (USFS) routinely conducts prescribed fires at the Savannah River Site (SRS), a heavily wooded Department of Energy (DOE) facility located in southwest South Carolina. For many years, the Savannah River National Laboratory (SRNL) has provided forecasts of weather conditions in support of the fire program, including an estimated mixing depth using potential temperature and turbulence change with height at a given location. This paper examines trends in the average estimated mixing depth daily maximum at the SRS over an extended period of time (4.75 years) derived from numerical atmospheric simulations using two versions of the Regional Atmospheric Modeling System (RAMS). This allows for differences to be seen between the model versions, as well as trends on a multi-year time frame. In addition, comparisons of predicted mixing depth for individual days in which special balloon soundings were released are also discussed.

  4. Maximum Entropy Fundamentals

    Directory of Open Access Journals (Sweden)

    F. Topsøe

    2001-09-01

    Full Text Available Abstract: In its modern formulation, the Maximum Entropy Principle was promoted by E.T. Jaynes, starting in the mid-fifties. The principle dictates that one should look for a distribution, consistent with available information, which maximizes the entropy. However, this principle focuses only on distributions and it appears advantageous to bring information theoretical thinking more prominently into play by also focusing on the "observer" and on coding. This view was brought forward by the second named author in the late seventies and is the view we will follow-up on here. It leads to the consideration of a certain game, the Code Length Game and, via standard game theoretical thinking, to a principle of Game Theoretical Equilibrium. This principle is more basic than the Maximum Entropy Principle in the sense that the search for one type of optimal strategies in the Code Length Game translates directly into the search for distributions with maximum entropy. In the present paper we offer a self-contained and comprehensive treatment of fundamentals of both principles mentioned, based on a study of the Code Length Game. Though new concepts and results are presented, the reading should be instructional and accessible to a rather wide audience, at least if certain mathematical details are left aside at a rst reading. The most frequently studied instance of entropy maximization pertains to the Mean Energy Model which involves a moment constraint related to a given function, here taken to represent "energy". This type of application is very well known from the literature with hundreds of applications pertaining to several different elds and will also here serve as important illustration of the theory. But our approach reaches further, especially regarding the study of continuity properties of the entropy function, and this leads to new results which allow a discussion of models with so-called entropy loss. These results have tempted us to speculate over

  5. 22 CFR 201.67 - Maximum freight charges.

    Science.gov (United States)

    2010-04-01

    ..., commodity rate classification, quantity, vessel flag category (U.S.-or foreign-flag), choice of ports, and... the United States. (2) Maximum charter rates. (i) USAID will not finance ocean freight under any... owner(s). (4) Maximum liner rates. USAID will not finance ocean freight for a cargo liner shipment at a...

  6. Summary (and) recommendations

    International Nuclear Information System (INIS)

    1992-01-01

    This report looks at the Health and Safety record at the Atomic Weapons Establishment at Aldermaston. The last outside report was by Pochin in 1978 which recommended that staffing for health physicists and maintenance staff should be increased and that some buildings where solid and liquid radioactive wastes were processed should be replaced. A new facility to process contaminated heavy equipment was also recommended. This report finds that none of the recommendations have been fully implemented. It also lists accidents, fires and worker contamination. It is concluded that some of the problems are that nuclear weapons production is inherently unsafe and cannot be made safe, that the secrecy surrounding the establishments' safety record is not good for improving it and finally the report calls for production at Aldermaston to be halted. (UK)

  7. Recommending Multidimensional Queries

    Science.gov (United States)

    Giacometti, Arnaud; Marcel, Patrick; Negre, Elsa

    Interactive analysis of datacube, in which a user navigates a cube by launching a sequence of queries is often tedious since the user may have no idea of what the forthcoming query should be in his current analysis. To better support this process we propose in this paper to apply a Collaborative Work approach that leverages former explorations of the cube to recommend OLAP queries. The system that we have developed adapts Approximate String Matching, a technique popular in Information Retrieval, to match the current analysis with the former explorations and help suggesting a query to the user. Our approach has been implemented with the open source Mondrian OLAP server to recommend MDX queries and we have carried out some preliminary experiments that show its efficiency for generating effective query recommendations.

  8. Avoiding congestion in recommender systems

    International Nuclear Information System (INIS)

    Ren, Xiaolong; Lü, Linyuan; Liu, Runran; Zhang, Jianlin

    2014-01-01

    Recommender systems use the historical activities and personal profiles of users to uncover their preferences and recommend objects. Most of the previous methods are based on objects’ (and/or users’) similarity rather than on their difference. Such approaches are subject to a high risk of increasingly exposing users to a narrowing band of popular objects. As a result, a few objects may be recommended to an enormous number of users, resulting in the problem of recommendation congestion, which is to be avoided, especially when the recommended objects are limited resources. In order to quantitatively measure a recommendation algorithm's ability to avoid congestion, we proposed a new metric inspired by the Gini index, which is used to measure the inequality of the individual wealth distribution in an economy. Besides this, a new recommendation method called directed weighted conduction (DWC) was developed by considering the heat conduction process on a user–object bipartite network with different thermal conductivities. Experimental results obtained for three benchmark data sets showed that the DWC algorithm can effectively avoid system congestion, and greatly improve the novelty and diversity, while retaining relatively high accuracy, in comparison with the state-of-the-art methods. (paper)

  9. Recommendation Sets and Choice Queries

    DEFF Research Database (Denmark)

    Viappiani, Paolo Renato; Boutilier, Craig

    2011-01-01

    Utility elicitation is an important component of many applications, such as decision support systems and recommender systems. Such systems query users about their preferences and offer recommendations based on the system's belief about the user's utility function. We analyze the connection between...... the problem of generating optimal recommendation sets and the problem of generating optimal choice queries, considering both Bayesian and regret-based elicitation. Our results show that, somewhat surprisingly, under very general circumstances, the optimal recommendation set coincides with the optimal query....

  10. Serum C-reactive protein concentrations in healthy Miniature Schnauzer dogs.

    Science.gov (United States)

    Wong, Valerie M; Kidney, Beverly A; Snead, Elisabeth C R; Myers, Sherry L; Jackson, Marion L

    2011-09-01

    C-reactive protein (CRP) is a sensitive marker for inflammation in people and dogs. In people, an association between CRP concentration and atherosclerosis has been reported. Atherosclerosis is rare in dogs, but the Miniature Schnauzer breed may be at increased risk for developing this vascular disease. It is not known if CRP concentrations in Miniature Schnauzer dogs differ from those in other dog breeds. Our objectives were to validate an automated human CRP assay for measuring CRP in dogs and compare CRP concentrations in healthy Miniature Schnauzer dogs with those in non-Miniature Schnauzer breeds. Sera from 37 non-Miniature Schnauzer dogs with inflammatory disease were pooled and used to validate a human CRP immunoturbidimetric assay for measuring canine CRP. Blood was collected from 20 healthy Miniature Schnauzer dogs and 41 healthy dogs of other breeds. Median serum CRP concentration of healthy Miniature Schnauzer dogs was compared with that of healthy non-Miniature Schnauzer dogs. The human CRP assay measured CRP reliably with linearity between 0 and 20 mg/L. CRP concentration for healthy Miniature Schnauzer dogs (median 4.0 mg/L, minimum-maximum 0-18.2 mg/L) was significantly higher than for the healthy non-Miniature Schnauzer dogs (median 0.1 mg/L, minimum-maximum 0-10.7 mg/L); 17 of the 20 Miniature Schnauzer dogs had values that overlapped with those of the non-Miniature Schnauzer dogs. Median CRP concentration of Miniature Schnauzer dogs was slightly higher than that of other breeds of dogs. A relationship between higher CRP concentration in Miniature Schnauzer dogs and idiopathic hyperlipidemia, pancreatitis, and possible increased risk for atherosclerosis remains to be determined. ©2011 American Society for Veterinary Clinical Pathology.

  11. The clinical value of enzyme-multiplied immunoassay technique monitoring the plasma concentrations of cyclosporine A after renal transplantation

    Directory of Open Access Journals (Sweden)

    Xiao-Hui Luo

    2011-05-01

    Full Text Available The feasibility and the clinical value of the enzyme-multiplied immunoassay technique (EMIT monitoring of blood concentrations of cyclosporine A (CsA in patients treated with CsA were investigated after kidney transplantation. The validation method was performed to the EMIT determination of CsA blood concentration, the CsA whole blood ‘trough concentrations (C0 of patients in different time periods after renal transplantation were monitored, and combined with the clinical complications, the statistical results were analyzed and compared. EMIT was precise, accurate and stable, also with a high quality control. The mean postoperative blood concentration of CsA was as follows: 12 months, (185.6 ± 28.1ng/mL. The toxic reaction rate of CsA blood concentration within the recommended therapeutic concentration was 14. 1%, significantly lower than that of the none-recommended dose group (37.2% (P < 0.05; the transplantation rejection rate was 4.4%, significantly lower than that of the none-recommended dose group (22.5% (P < 0.05. Using EMIT to monitor the blood concentration of CsA as the routine laboratory method is feasible, and is able to reduce the CsA toxicity and rejection significantly, leading to achieving the desired therapeutic effect. Keywords: enzyme-multiplied immunoassay technique, renal transplantation, cyclosporin A, blood concentration monitoring

  12. A heterogeneous graph-based recommendation simulator

    Energy Technology Data Exchange (ETDEWEB)

    Yeonchan, Ahn [Seoul National University; Sungchan, Park [Seoul National University; Lee, Matt Sangkeun [ORNL; Sang-goo, Lee [Seoul National University

    2013-01-01

    Heterogeneous graph-based recommendation frameworks have flexibility in that they can incorporate various recommendation algorithms and various kinds of information to produce better results. In this demonstration, we present a heterogeneous graph-based recommendation simulator which enables participants to experience the flexibility of a heterogeneous graph-based recommendation method. With our system, participants can simulate various recommendation semantics by expressing the semantics via meaningful paths like User Movie User Movie. The simulator then returns the recommendation results on the fly based on the user-customized semantics using a fast Monte Carlo algorithm.

  13. 1990 recommendations of ICRP

    International Nuclear Information System (INIS)

    Clarke, R.H.

    1991-01-01

    The Main Commission of ICRP finalised its new recommendations during its November 1990 meeting. The recommendations will appear in the Annals of the ICRP in 1991 as Publication 60. This paper represents a personal summary of these recommendations. It covers the basic biological risk estimates and the conceptual framework of the system of radiological protection, the definition of radiation detriment and its use both in the definition of radiation quantities and in the establishment of the dose limits adopted by the Main Commissions. (author)

  14. Determination of the maximum-depth to potential field sources by a maximum structural index method

    Science.gov (United States)

    Fedi, M.; Florio, G.

    2013-01-01

    A simple and fast determination of the limiting depth to the sources may represent a significant help to the data interpretation. To this end we explore the possibility of determining those source parameters shared by all the classes of models fitting the data. One approach is to determine the maximum depth-to-source compatible with the measured data, by using for example the well-known Bott-Smith rules. These rules involve only the knowledge of the field and its horizontal gradient maxima, and are independent from the density contrast. Thanks to the direct relationship between structural index and depth to sources we work out a simple and fast strategy to obtain the maximum depth by using the semi-automated methods, such as Euler deconvolution or depth-from-extreme-points method (DEXP). The proposed method consists in estimating the maximum depth as the one obtained for the highest allowable value of the structural index (Nmax). Nmax may be easily determined, since it depends only on the dimensionality of the problem (2D/3D) and on the nature of the analyzed field (e.g., gravity field or magnetic field). We tested our approach on synthetic models against the results obtained by the classical Bott-Smith formulas and the results are in fact very similar, confirming the validity of this method. However, while Bott-Smith formulas are restricted to the gravity field only, our method is applicable also to the magnetic field and to any derivative of the gravity and magnetic field. Our method yields a useful criterion to assess the source model based on the (∂f/∂x)max/fmax ratio. The usefulness of the method in real cases is demonstrated for a salt wall in the Mississippi basin, where the estimation of the maximum depth agrees with the seismic information.

  15. Introduction on health recommender systems.

    Science.gov (United States)

    Sanchez-Bocanegra, C L; Sanchez-Laguna, F; Sevillano, J L

    2015-01-01

    People are looking for appropriate health information which they are concerned about. The Internet is a great resource of this kind of information, but we have to be careful if we don't want to get harmful info. Health recommender systems are becoming a new wave for apt health information as systems suggest the best data according to the patients' needs.The main goals of health recommender systems are to retrieve trusted health information from the Internet, to analyse which is suitable for the user profile and select the best that can be recommended, to adapt their selection methods according to the knowledge domain and to learn from the best recommendations.A brief definition of recommender systems will be given and an explanation of how are they incorporated in the health sector. A description of the main elementary recommender methods as well as their most important problems will also be made. And, to finish, the state of the art will be described.

  16. 40 CFR 141.13 - Maximum contaminant levels for turbidity.

    Science.gov (United States)

    2010-07-01

    ... turbidity. 141.13 Section 141.13 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... Maximum contaminant levels for turbidity. The maximum contaminant levels for turbidity are applicable to... part. The maximum contaminant levels for turbidity in drinking water, measured at a representative...

  17. A subjective supply–demand model: the maximum Boltzmann/Shannon entropy solution

    International Nuclear Information System (INIS)

    Piotrowski, Edward W; Sładkowski, Jan

    2009-01-01

    The present authors have put forward a projective geometry model of rational trading. The expected (mean) value of the time that is necessary to strike a deal and the profit strongly depend on the strategies adopted. A frequent trader often prefers maximal profit intensity to the maximization of profit resulting from a separate transaction because the gross profit/income is the adopted/recommended benchmark. To investigate activities that have different periods of duration we define, following the queuing theory, the profit intensity as a measure of this economic category. The profit intensity in repeated trading has a unique property of attaining its maximum at a fixed point regardless of the shape of demand curves for a wide class of probability distributions of random reverse transactions (i.e. closing of the position). These conclusions remain valid for an analogous model based on supply analysis. This type of market game is often considered in research aiming at finding an algorithm that maximizes profit of a trader who negotiates prices with the Rest of the World (a collective opponent), possessing a definite and objective supply profile. Such idealization neglects the sometimes important influence of an individual trader on the demand/supply profile of the Rest of the World and in extreme cases questions the very idea of demand/supply profile. Therefore we put forward a trading model in which the demand/supply profile of the Rest of the World induces the (rational) trader to (subjectively) presume that he/she lacks (almost) all knowledge concerning the market but his/her average frequency of trade. This point of view introduces maximum entropy principles into the model and broadens the range of economic phenomena that can be perceived as a sort of thermodynamical system. As a consequence, the profit intensity has a fixed point with an astonishing connection with Fibonacci classical works and looking for the quickest algorithm for obtaining the extremum of a

  18. A subjective supply-demand model: the maximum Boltzmann/Shannon entropy solution

    Science.gov (United States)

    Piotrowski, Edward W.; Sładkowski, Jan

    2009-03-01

    The present authors have put forward a projective geometry model of rational trading. The expected (mean) value of the time that is necessary to strike a deal and the profit strongly depend on the strategies adopted. A frequent trader often prefers maximal profit intensity to the maximization of profit resulting from a separate transaction because the gross profit/income is the adopted/recommended benchmark. To investigate activities that have different periods of duration we define, following the queuing theory, the profit intensity as a measure of this economic category. The profit intensity in repeated trading has a unique property of attaining its maximum at a fixed point regardless of the shape of demand curves for a wide class of probability distributions of random reverse transactions (i.e. closing of the position). These conclusions remain valid for an analogous model based on supply analysis. This type of market game is often considered in research aiming at finding an algorithm that maximizes profit of a trader who negotiates prices with the Rest of the World (a collective opponent), possessing a definite and objective supply profile. Such idealization neglects the sometimes important influence of an individual trader on the demand/supply profile of the Rest of the World and in extreme cases questions the very idea of demand/supply profile. Therefore we put forward a trading model in which the demand/supply profile of the Rest of the World induces the (rational) trader to (subjectively) presume that he/she lacks (almost) all knowledge concerning the market but his/her average frequency of trade. This point of view introduces maximum entropy principles into the model and broadens the range of economic phenomena that can be perceived as a sort of thermodynamical system. As a consequence, the profit intensity has a fixed point with an astonishing connection with Fibonacci classical works and looking for the quickest algorithm for obtaining the extremum of a

  19. Recommended system of application and development

    Science.gov (United States)

    Wang, Wei

    2018-04-01

    A recommender system is a project that helps users identify their wishes and needs. The recommender system has been successfully applied to many e-commerce environments, such as news, film, music, books and other areas of recommendation. This paper mainly discusses the application of recommendation technology in software engineering, data and knowledge engineering, configurable projects and persuasion technology, and summarizes the development trend of recommendation technology in the future.

  20. Modelling maximum canopy conductance and transpiration in ...

    African Journals Online (AJOL)

    There is much current interest in predicting the maximum amount of water that can be transpired by Eucalyptus trees. It is possible that industrial waste water may be applied as irrigation water to eucalypts and it is important to predict the maximum transpiration rates of these plantations in an attempt to dispose of this ...

  1. 40 CFR 141.62 - Maximum contaminant levels for inorganic contaminants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant levels for inorganic contaminants. 141.62 Section 141.62 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Water Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.62 Maximum...

  2. Weak scale from the maximum entropy principle

    Science.gov (United States)

    Hamada, Yuta; Kawai, Hikaru; Kawana, Kiyoharu

    2015-03-01

    The theory of the multiverse and wormholes suggests that the parameters of the Standard Model (SM) are fixed in such a way that the radiation of the S3 universe at the final stage S_rad becomes maximum, which we call the maximum entropy principle. Although it is difficult to confirm this principle generally, for a few parameters of the SM, we can check whether S_rad actually becomes maximum at the observed values. In this paper, we regard S_rad at the final stage as a function of the weak scale (the Higgs expectation value) vh, and show that it becomes maximum around vh = {{O}} (300 GeV) when the dimensionless couplings in the SM, i.e., the Higgs self-coupling, the gauge couplings, and the Yukawa couplings are fixed. Roughly speaking, we find that the weak scale is given by vh ˜ T_{BBN}2 / (M_{pl}ye5), where ye is the Yukawa coupling of electron, T_BBN is the temperature at which the Big Bang nucleosynthesis starts, and M_pl is the Planck mass.

  3. Concentration profiles near an activated enzyme.

    Science.gov (United States)

    Park, Soohyung; Agmon, Noam

    2008-09-25

    When a resting enzyme is activated, substrate concentration profile evolves in its vicinity, ultimately tending to steady state. We use modern theories for many-body effects on diffusion-influenced reactions to derive approximate analytical expressions for the steady-state profile and the Laplace transform of the transient concentration profiles. These show excellent agreement with accurate many-particle Brownian-dynamics simulations for the Michaelis-Menten kinetics. The steady-state profile has a hyperbolic dependence on the distance of the substrate from the enzyme, albeit with a prefactor containing the complexity of the many-body effects. These are most conspicuous for the substrate concentration at the surface of the enzyme. It shows an interesting transition as a function of the enzyme turnover rate. When it is high, the contact concentration decays monotonically to steady state. However, for slow turnover it is nonmonotonic, showing a minimum due to reversible substrate binding, then a maximum due to diffusion of new substrate toward the enzyme, and finally decay to steady state. Under certain conditions one can obtain a good estimate for the critical value of the turnover rate constant at the transition.

  4. [Estimation of maximum acceptable concentration of lead and cadmium in plants and their medicinal preparations].

    Science.gov (United States)

    Zitkevicius, Virgilijus; Savickiene, Nijole; Abdrachmanovas, Olegas; Ryselis, Stanislovas; Masteiková, Rūta; Chalupova, Zuzana; Dagilyte, Audrone; Baranauskas, Algirdas

    2003-01-01

    Heavy metals (lead, cadmium) are possible dashes which quantity is defined by the limiting acceptable contents. Different drugs preparations: infusions, decoctions, tinctures, extracts, etc. are produced using medicinal plants. The objective of this research was to study the impurities of heavy metals (lead, cadmium) in medicinal plants and some drug preparations. We investigated liquid extracts of fruits Crataegus monogyna Jacq. and herbs of Echinacea purpurea Moench., tinctures--of herbs Leonurus cardiaca L. The raw materials were imported from Poland. Investigations were carried out in cooperation with the Laboratory of Antropogenic Factors of the Institute for Biomedical Research. Amounts of lead and cadmium were established after "dry" mineralisation using "Perkin-Elmer Zeeman/3030" model electrothermic atomic absorption spectrophotometer (ETG AAS/Zeeman). It was established that lead is absorbed most efficiently after estimation of absorption capacity of cellular fibers. About 10.73% of lead crosses tinctures and extracts, better cadmium--49.63%. Herbs of Leonurus cardiaca L. are the best in holding back lead and cadmium. About 14.5% of lead and cadmium crosses the tincture of herbs Leonurus cardiaca L. We estimated the factors of heavy metals (lead, cadmium) in the liquid extracts of Crataegus monogyna Jacq. and Echinacea purpurea Moench., tincture of Leonurus cardiaca L. after investigations of heavy metals (lead, cadmium) in drugs and preparations of it. The amounts of heavy metals (lead, cadmium) don't exceed the allowable norms in fruits of Crataegus monogyna Jacq., herbs of Leonurus cardiaca L. and Echinacea purpurea Moench. after estimation of lead and cadmium extraction factors, the maximum of acceptable daily intake and the quantity of drugs consumption in day.

  5. Accurate modeling and maximum power point detection of ...

    African Journals Online (AJOL)

    Accurate modeling and maximum power point detection of photovoltaic ... Determination of MPP enables the PV system to deliver maximum available power. ..... adaptive artificial neural network: Proposition for a new sizing procedure.

  6. 40 CFR 141.61 - Maximum contaminant levels for organic contaminants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant levels for organic contaminants. 141.61 Section 141.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.61 Maximum contaminant...

  7. The power and robustness of maximum LOD score statistics.

    Science.gov (United States)

    Yoo, Y J; Mendell, N R

    2008-07-01

    The maximum LOD score statistic is extremely powerful for gene mapping when calculated using the correct genetic parameter value. When the mode of genetic transmission is unknown, the maximum of the LOD scores obtained using several genetic parameter values is reported. This latter statistic requires higher critical value than the maximum LOD score statistic calculated from a single genetic parameter value. In this paper, we compare the power of maximum LOD scores based on three fixed sets of genetic parameter values with the power of the LOD score obtained after maximizing over the entire range of genetic parameter values. We simulate family data under nine generating models. For generating models with non-zero phenocopy rates, LOD scores maximized over the entire range of genetic parameters yielded greater power than maximum LOD scores for fixed sets of parameter values with zero phenocopy rates. No maximum LOD score was consistently more powerful than the others for generating models with a zero phenocopy rate. The power loss of the LOD score maximized over the entire range of genetic parameters, relative to the maximum LOD score calculated using the correct genetic parameter value, appeared to be robust to the generating models.

  8. OARSI Clinical Trials Recommendations

    DEFF Research Database (Denmark)

    McAlindon, T. E.; Driban, J. B.; Henrotin, Y.

    2015-01-01

    The goal of this document is to update the original OARSI recommendations specifically for the design, conduct, and reporting of clinical trials that target symptom or structure modification among individuals with knee osteoarthritis (OA). To develop recommendations for the design, conduct...

  9. Research on Long Tail Recommendation Algorithm

    Science.gov (United States)

    Hu, Xuezhi; Zhang, Chuang; Wu, Ming; Zeng, Yang

    2017-10-01

    Most recommendation systems in the major electronic commerce platforms are influenced by the long tail effect more or less. There are sufficient researches of how to assess recommendation effect while no criteria to evaluate long tail recommendation rate. In this study, we first discussed the existing problems of recommending long tail products through specific experiments. Then we proposed a long tail evaluation criteria and compared the performance in long tail recommendation between different models.

  10. A volatile organics concentrator for use in monitoring Space Station water quality

    Science.gov (United States)

    Ehntholt, Daniel J.; Bodek, Itamar; Valentine, James R.; Trabanino, Rudy; Vincze, Johanna E.; Sauer, Richard L.

    1990-01-01

    The process used to identify, select, and design an approach to the isolation and concentration of volatile organic compounds from a water sample prior to chemical analysis in a microgravity environment is discerned. The trade analysis leading to the recommended volatile organics concentrator (VOC) concept to be tested in a breadboard device is presented. The system covers the areas of gases, volatile separation from water, and water removal/gas chromatograph/mass spectrometer interface. Five options for potential use in the VOC and GC/MS system are identified and ranked, and also nine options are presented for separation of volatiles from the water phase. Seven options for use in the water removal/GC column and MS interface are also identified and included in the overall considerations. A final overall recommendation for breadboard VOC testing is given.

  11. Maximum Power Training and Plyometrics for Cross-Country Running.

    Science.gov (United States)

    Ebben, William P.

    2001-01-01

    Provides a rationale for maximum power training and plyometrics as conditioning strategies for cross-country runners, examining: an evaluation of training methods (strength training and maximum power training and plyometrics); biomechanic and velocity specificity (role in preventing injury); and practical application of maximum power training and…

  12. Maximum Likelihood DOA Estimation of Multiple Wideband Sources in the Presence of Nonuniform Sensor Noise

    Directory of Open Access Journals (Sweden)

    K. Yao

    2007-12-01

    Full Text Available We investigate the maximum likelihood (ML direction-of-arrival (DOA estimation of multiple wideband sources in the presence of unknown nonuniform sensor noise. New closed-form expression for the direction estimation Cramér-Rao-Bound (CRB has been derived. The performance of the conventional wideband uniform ML estimator under nonuniform noise has been studied. In order to mitigate the performance degradation caused by the nonuniformity of the noise, a new deterministic wideband nonuniform ML DOA estimator is derived and two associated processing algorithms are proposed. The first algorithm is based on an iterative procedure which stepwise concentrates the log-likelihood function with respect to the DOAs and the noise nuisance parameters, while the second is a noniterative algorithm that maximizes the derived approximately concentrated log-likelihood function. The performance of the proposed algorithms is tested through extensive computer simulations. Simulation results show the stepwise-concentrated ML algorithm (SC-ML requires only a few iterations to converge and both the SC-ML and the approximately-concentrated ML algorithm (AC-ML attain a solution close to the derived CRB at high signal-to-noise ratio.

  13. Estimation of radon concentration in soil and groundwater samples of Northern Rajasthan, India

    International Nuclear Information System (INIS)

    Mittal, Sudhir; Asha Rani; Mehra, Rohit

    2015-01-01

    In the present investigation, analysis of radon concentration in 20 water and soil samples collected from different locations of Bikaner and Jhunjhunu districts of Rajasthan, India has been carried out by using RAD7 an electronic Radon detector. The water samples are taken from hand pumps and tube wells having depths ranging from 50 to 600 feet. All the soil gas measurements have been carried out at 100 cm depth. The measured radon concentration in water samples lies in the range from 0.50 to 22 Bq l -1 with the mean value of 4.42 Bq l -1 . Only in one water sample radon concentration is found to be higher than the safe limit of 11 Bq l -1 recommended US Environmental Protection Agency (USEPA, 1991). The measured value of radon concentration in all ground water samples is within the safe limit from 4 to 40 Bq l -1 recommended by United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR, 2008). The total annual effective dose estimated due to radon concentration in water ranges from 1.37 to 60 μSV y -1 with the mean value of 12.08 μSV y -1 . The total annual effective dose from all locations of our studied area is found to be well within the safe limit 0.1 mSv y -1 recommended by World Health Organization (WHO, 2004) and European Council (ED, 1998). Radon measurement in soil samples varies from 941 to 10050 Bq m -3 with the mean value of 4561 Bq m -3 , The radon concentration observed from the soil samples from our study area lies within the range reported by other investigators. Moreover a positive correlation of radon concentration in water with soil samples has been observed. It was observed that the soil and water of Bikaner and Jhunjhunu districts are suitable for drinking and construction purpose without posing any health hazard. (author)

  14. Defining and Supporting Narrative-driven Recommendation

    DEFF Research Database (Denmark)

    Bogers, Toine; Koolen, Marijn

    2017-01-01

    Research into recommendation algorithms has made great strides in recent years. However, these algorithms are typically applied in relatively straightforward scenarios: given information about a user's past preferences, what will they like in the future? Recommendation is often more complex......: evaluating recommended items never takes place in a vacuum, and it is often a single step in the user's more complex background task. In this paper, we define a specific type of recommendation scenario called narrative-driven recommendation, where the recommendation process is driven by both a log...... of the user's past transactions as well as a narrative description of their current interest(s). Through an analysis of a set of real-world recommendation narratives from the LibraryThing forums, we demonstrate the uniqueness and richness of this scenario and highlight common patterns and properties...

  15. The ciprofloxacin target AUC : MIC ratio is not reached in hospitalized patients with the recommended dosing regimens.

    Science.gov (United States)

    Haeseker, Michiel; Stolk, Leo; Nieman, Fred; Hoebe, Christian; Neef, Cees; Bruggeman, Cathrien; Verbon, Annelies

    2013-01-01

    The aim of this study was to determine the ciprofloxacin serum concentrations in hospitalized patients and to determine which percentage reached the efficacy target of AUC : MIC > 125. Additionally, the influence of demographic anthropomorphic and clinical parameters on the pharmacokinetics and pharmacodynamics of ciprofloxacin were investigated. In serum of 80 hospitalized patients ciprofloxacin concentrations were measured with reverse phase high performance liquid chromatography with fluorescence detection. The ciprofloxacin dose was 400-1200 mg day(-1) i.v. in two or three doses depending on renal function and causative bacteria. Pharmacokinetic parameters were calculated with maximum a posteriori Bayesian estimation (MW\\PHARM 3.60). A two compartment open model was used. Mean (± SD) age was 66 (± 17) years, the mean clearance corrected for bodyweight was 0.24 l h(-1) kg(-1) and the mean AUC was 49 mg l(-1) h. Ciprofloxacin clearance and thus AUC were associated with both age and serum creatinine. Of all patients, 21% and 75% of the patients, did not reach the proposed ciprofloxacin AUC : MIC > 125 target with MICs of 0.25 and 0.5 mg l(-1), respectively. A computer simulated increase in the daily dose from 800 mg to 1200 mg, decreased these percentages to 1% and 37%, respectively. A substantial proportion of the hospitalized patients did not reach the target ciprofloxacin AUC : MIC and are suboptimally dosed with recommended doses. Taking into account the increasing resistance to ciprofloxacin worldwide, a ciprofloxacin dose of 1200 mg i.v. daily in patients with normal renal function is necessary to reach the targeted AUC : MIC > 125. © 2012 The Authors. British Journal of Clinical Pharmacology © 2012 The British Pharmacological Society.

  16. Possible future scenarios for atmospheric concentration of greenhouse gases. A simplified thermodynamic approach

    International Nuclear Information System (INIS)

    Angulo-Brown, F.; Sanchez-Salas, N.; Barranco-Jimenez, M.A.; Rosales, M.A.

    2009-01-01

    Most of the increase in concentrations of greenhouse gases in the Earth's atmosphere is mainly due to anthropogenic activities. This is particularly significant in the case of CO 2 . The atmospheric concentration of CO 2 has systematically increased since the Industrial Revolution (260 ppm), with a remarkable raise after the 1970s until the present day (380 ppm). If this increasing tendency is maintained, the last report of the Intergovernmental Panel on Climate Change (IPCC) estimates that, for the year 2100, the CO 2 concentration can augment up to approximately 675 ppm. In this work it is assumed that the quantity of anthropogenic greenhouse gases emitted to the Earth's atmosphere is proportional to the quantity of heat rejected to the environment by internal combustion heat engines. It is also assumed that this increasing tendency of CO 2 due to men's activity stems from a mode of energy production mainly based on a maximum-power output paradigm. With these hypotheses, a thermoeconomic optimization of a thermal engine model under two regimes of performance: the maximum-power regime and the so-called ecological function criterion is presented. This last regime consists in maximizing a function that represents a good compromise between high power output and low entropy production. It is showed that, under maximum ecological conditions, the emissions of thermal energy to the environment are reduced approximately up to 50%. Thus working under this mode of performance the slope of the curves of CO 2 concentration, for instance, drastically diminishes. A simple qualitative criterion to design ecological taxes is also suggested. (author)

  17. Recommendations relating to safety-critical real-time software in nuclear power plants

    International Nuclear Information System (INIS)

    1992-01-01

    The Advisory Committee on Nuclear Safety (ACNS) has reviewed safety issues associated with the software for the digital computers in the safety shutdown systems for the Darlington NGS. From this review the ACNS has developed four recommendations for safety-critical real-time software in nuclear power plants. These recommendations cover: the completion of the present efforts to develop an overall standard and sub-tier standards for safety-critical real-time software; the preparation of schedules and lists of responsibilities for this development; the concentration of AECB efforts on ensuring the scrutability of safety-critical real-time software; and, the collection of data on reliability and causes of failure (error) of safety-critical real-time software systems and on the probability and causes of common-mode failures (errors). (9 refs.)

  18. Dry soil diurnal quasi-periodic oscillations in soil 222Rn concentrations

    International Nuclear Information System (INIS)

    Tommasone Pascale, F.; De Francesco, S.; Carbone, P.; Cuoco, E.; Tedesco, D.

    2014-01-01

    222 Rn concentrations have been monitored during the dry season in August 2009 and August 2010, in a reworked alluvial-pyroclastic soil of the Pietramelara Plain, in Southern Italy, with the aim of determining the role of atmospheric factors in producing the quasi-periodic oscillations in soil 222 Rn concentrations reported in the literature. In this study we present the results of a detailed analysis and matching of soil 222 Rn concentrations, meteorological and solar parameters where the observed oscillations feature a characteristic behavior with second order build-up and depletion limbs, separated by a daily maximum and minimum. All these features are clearly shown to be tied to sunrise and sunset timings and environmental radiative flux regimes. Furthermore, a significant, and previously unreported, second order correlation (r 2  = 0.73) between daily maximum hourly global radiation and the daily range of soil 222 Rn concentrations has been detected, allowing estimates of the amplitude of these oscillations to be made from estimated or measured solar radiation data. The correlation has been found to be valid even in the presence of persistent patchy daytime cloudiness. In this case a daytime prolongation of the night-time build up stage and an attenuation or even suppression of daytime depletion is observed (a previously unreported effect). Neither soil cracking, nor precipitation, both suggested in some studies as causative factors for these oscillations, during the dry season appear to be necessary in explaining their occurrence. We also report the results of an artificial shading experiment, conducted in August 2009, that further support this conclusion. As soil 222 Rn concentrations during the dry season show a characteristic daily cycle, radon monitoring in soils under these conditions necessarily has to be gauged to the timings of the daily maximum and minimum, as well as to the eventual occurrence of cloudiness and to its related effects, in order to

  19. Effect of Applying Chemical Fertilizers on Concentration of Cd, Pb and Zn in Agricultural Soils

    Directory of Open Access Journals (Sweden)

    Hossein Pourmoghadas

    2017-03-01

    Full Text Available Background &Objective:  Nowadays uncontrolled uses of chemical fertilizers which have many heavy metals such as Cadmium, Lead and Zinc in addition have economic problems, cause to serious damages in the environment. Therefore uncontrolled application of fertilizers can cause accumulation contaminants in soil, water sources and increasing in plants and human & animals’ food chain. The main objective of this research was to investigate the effects of chemical fertilizers application to increase heavy metals in agricultural soils at directions to prevent contamination in water sources, agricultural products and the best uses of chemical fertilizers. Methods: In this study, 20 soil samples and 5 useful chemical fertilizer samples were collected and investigated. After fertilizer and soil samples were prepared, digested and filtered, heavy metals were determined with using atomic absorption. Results: The results of this study showed that, Cd in Diammonum phosphate  fertilizer 1.25 times, Super phosphate triple 1.7 times and in Macro granular fertilizer 1.5 times were as much as maximum acceptable concentration in chemical fertilizers. Cadmium concentration in all of the Jarghoye (Isfahan agricultural soil samples 3 to 7 times and in the Mobarake village (Najaf abad agricultural soil samples 10 to 35 times were as much as maximum acceptable concentration in agricultural soils. But Pb and Zn concentration in all of the agricultural soil samples was less than the amount of maximum acceptable concentration. Conclusion: Phosphate chemical fertilizers were positive effects to increase concentration of Pb and Zn in agricultural soils. Therefore, application of the fertilizer must be more attention because of increasing heavy metals in the agriculture soils and probably increasing heavy metals in food chain.  

  20. Hybrid context aware recommender systems

    Science.gov (United States)

    Jain, Rajshree; Tyagi, Jaya; Singh, Sandeep Kumar; Alam, Taj

    2017-10-01

    Recommender systems and context awareness is currently a vital field of research. Most hybrid recommendation systems implement content based and collaborative filtering techniques whereas this work combines context and collaborative filtering. The paper presents a hybrid context aware recommender system for books and movies that gives recommendations based on the user context as well as user or item similarity. It also addresses the issue of dimensionality reduction using weighted pre filtering based on dynamically entered user context and preference of context. This unique step helps to reduce the size of dataset for collaborative filtering. Bias subtracted collaborative filtering is used so as to consider the relative rating of a particular user and not the absolute values. Cosine similarity is used as a metric to determine the similarity between users or items. The unknown ratings are calculated and evaluated using MSE (Mean Squared Error) in test and train datasets. The overall process of recommendation has helped to personalize recommendations and give more accurate results with reduced complexity in collaborative filtering.

  1. The last glacial maximum

    Science.gov (United States)

    Clark, P.U.; Dyke, A.S.; Shakun, J.D.; Carlson, A.E.; Clark, J.; Wohlfarth, B.; Mitrovica, J.X.; Hostetler, S.W.; McCabe, A.M.

    2009-01-01

    We used 5704 14C, 10Be, and 3He ages that span the interval from 10,000 to 50,000 years ago (10 to 50 ka) to constrain the timing of the Last Glacial Maximum (LGM) in terms of global ice-sheet and mountain-glacier extent. Growth of the ice sheets to their maximum positions occurred between 33.0 and 26.5 ka in response to climate forcing from decreases in northern summer insolation, tropical Pacific sea surface temperatures, and atmospheric CO2. Nearly all ice sheets were at their LGM positions from 26.5 ka to 19 to 20 ka, corresponding to minima in these forcings. The onset of Northern Hemisphere deglaciation 19 to 20 ka was induced by an increase in northern summer insolation, providing the source for an abrupt rise in sea level. The onset of deglaciation of the West Antarctic Ice Sheet occurred between 14 and 15 ka, consistent with evidence that this was the primary source for an abrupt rise in sea level ???14.5 ka.

  2. Modeling the Factors Impacting Pesticide Concentrations in Groundwater Wells

    DEFF Research Database (Denmark)

    Aisopou, Angeliki; Binning, Philip John; Albrechtsen, Hans-Jørgen

    2015-01-01

    This study examines the effect of pumping, hydrogeology, and pesticide characteristics on pesticide concentrations in production wells using a reactive transport model in two conceptual hydrogeologic systems; a layered aquifer with and without a stream present. The pumping rate can significantly...... affect the pesticide breakthrough time and maximum concentration at the well. The effect of the pumping rate on the pesticide concentration depends on the hydrogeology of the aquifer; in a layered aquifer, a high pumping rate resulted in a considerably different breakthrough than a low pumping rate......, while in an aquifer with a stream the effect of the pumping rate was insignificant. Pesticide application history and properties have also a great impact on the effect of the pumping rate on the concentration at the well. The findings of the study show that variable pumping rates can generate temporal...

  3. An investigation of factors influencing indoor radon concentrations

    International Nuclear Information System (INIS)

    Majborn, B.; Soerensen, A.; Nielsen, S.P.; Boetter-Jensen, L.

    1988-05-01

    Variations in indoor radon concentrations and some influencing factors have been studied during a two-year period (1986-1987) in 16 almost identical single-family houses.The annual average radon concentration in the houses varied from about 50 to about 400 Bq/m 3 . Variations in soil characteristics and radon concentration in soil gas could not be directly related to the variations of the average indoor radon concentrations. Most of the houses showed a ''normal'' seasonal variation of the radon concentration with a maximum in the winter and minimum in the summer. A deviating seasonal variation was found in three of the houses. Hourly data obtained in one unoccupied house during a period of 2-1/2 months showed no or only weak correlations between the indoor radon concentration and meteorological factors. However, for most of the houses, the seasonal variation of the indoor radon concentration was well correlated with the average indoor-outdoor temperature difference on a 2-month basis. It was demonstrated that the radon concentration can be strongly reduced in the Risoe houses if a district-heating duct, which is connected to all the houses, is ventilated, so that a slightly lowered pressure is maintained in the duct. 5 taps., 24 ill. (author)

  4. Maximum physical capacity testing in cancer patients undergoing chemotherapy

    DEFF Research Database (Denmark)

    Knutsen, L.; Quist, M; Midtgaard, J

    2006-01-01

    BACKGROUND: Over the past few years there has been a growing interest in the field of physical exercise in rehabilitation of cancer patients, leading to requirements for objective maximum physical capacity measurement (maximum oxygen uptake (VO(2max)) and one-repetition maximum (1RM)) to determin...... early in the treatment process. However, the patients were self-referred and thus highly motivated and as such are not necessarily representative of the whole population of cancer patients treated with chemotherapy....... in performing maximum physical capacity tests as these motivated them through self-perceived competitiveness and set a standard that served to encourage peak performance. CONCLUSION: The positive attitudes in this sample towards maximum physical capacity open the possibility of introducing physical testing...

  5. MAXIMUM PRINCIPLE FOR SUBSONIC FLOW WITH VARIABLE ENTROPY

    Directory of Open Access Journals (Sweden)

    B. Sizykh Grigory

    2017-01-01

    Full Text Available Maximum principle for subsonic flow is fair for stationary irrotational subsonic gas flows. According to this prin- ciple, if the value of the velocity is not constant everywhere, then its maximum is achieved on the boundary and only on the boundary of the considered domain. This property is used when designing form of an aircraft with a maximum critical val- ue of the Mach number: it is believed that if the local Mach number is less than unit in the incoming flow and on the body surface, then the Mach number is less then unit in all points of flow. The known proof of maximum principle for subsonic flow is based on the assumption that in the whole considered area of the flow the pressure is a function of density. For the ideal and perfect gas (the role of diffusion is negligible, and the Mendeleev-Clapeyron law is fulfilled, the pressure is a function of density if entropy is constant in the entire considered area of the flow. Shows an example of a stationary sub- sonic irrotational flow, in which the entropy has different values on different stream lines, and the pressure is not a function of density. The application of the maximum principle for subsonic flow with respect to such a flow would be unreasonable. This example shows the relevance of the question about the place of the points of maximum value of the velocity, if the entropy is not a constant. To clarify the regularities of the location of these points, was performed the analysis of the com- plete Euler equations (without any simplifying assumptions in 3-D case. The new proof of the maximum principle for sub- sonic flow was proposed. This proof does not rely on the assumption that the pressure is a function of density. Thus, it is shown that the maximum principle for subsonic flow is true for stationary subsonic irrotational flows of ideal perfect gas with variable entropy.

  6. Maximum power point tracker based on fuzzy logic

    International Nuclear Information System (INIS)

    Daoud, A.; Midoun, A.

    2006-01-01

    The solar energy is used as power source in photovoltaic power systems and the need for an intelligent power management system is important to obtain the maximum power from the limited solar panels. With the changing of the sun illumination due to variation of angle of incidence of sun radiation and of the temperature of the panels, Maximum Power Point Tracker (MPPT) enables optimization of solar power generation. The MPPT is a sub-system designed to extract the maximum power from a power source. In the case of solar panels power source. the maximum power point varies as a result of changes in its electrical characteristics which in turn are functions of radiation dose, temperature, ageing and other effects. The MPPT maximum the power output from panels for a given set of conditions by detecting the best working point of the power characteristic and then controls the current through the panels or the voltage across them. Many MPPT methods have been reported in literature. These techniques of MPPT can be classified into three main categories that include: lookup table methods, hill climbing methods and computational methods. The techniques vary according to the degree of sophistication, processing time and memory requirements. The perturbation and observation algorithm (hill climbing technique) is commonly used due to its ease of implementation, and relative tracking efficiency. However, it has been shown that when the insolation changes rapidly, the perturbation and observation method is slow to track the maximum power point. In recent years, the fuzzy controllers are used for maximum power point tracking. This method only requires the linguistic control rules for maximum power point, the mathematical model is not required and therefore the implementation of this control method is easy to real control system. In this paper, we we present a simple robust MPPT using fuzzy set theory where the hardware consists of the microchip's microcontroller unit control card and

  7. Annual limits on intake for members of the public and derived reference levels of radionuclide concentrations in the environment

    International Nuclear Information System (INIS)

    Mason, G.C.

    1983-01-01

    A proposal is presented recommending the introduction in Australia of Annual Limits on Intake of radionuclides for members of the public and of corresponding reference levels of radionuclide concentrations in the environment. The proposal is related to recent recommendations of the International Commission on Radiological Protection and draft recommendations under consideration by the International Atomic Energy Agency

  8. Quantitative aspects of isoeugenol contact allergy assessed by use and patch tests

    DEFF Research Database (Denmark)

    Johansen, J D; Andersen, Klaus Ejner; Menné, T

    1996-01-01

    in 4/19 (20%) of the test subjects. The ROAT was performed with a test solution of 0.2% isoeugenol in ethanol, which is the recommended maximum concentration used in perfumes, ethanol being applied as vehicle control. 4 weeks was the maximum exposure period. The upper arm was used as test site the 1st...

  9. Maximum entropy methods

    International Nuclear Information System (INIS)

    Ponman, T.J.

    1984-01-01

    For some years now two different expressions have been in use for maximum entropy image restoration and there has been some controversy over which one is appropriate for a given problem. Here two further entropies are presented and it is argued that there is no single correct algorithm. The properties of the four different methods are compared using simple 1D simulations with a view to showing how they can be used together to gain as much information as possible about the original object. (orig.)

  10. Is adherence to diet, physical activity, and body weight cancer prevention recommendations associated with colorectal cancer incidence in African American women?

    Science.gov (United States)

    Nomura, Sarah J O; Dash, Chiranjeev; Rosenberg, Lynn; Yu, Jeffrey; Palmer, Julie R; Adams-Campbell, Lucile L

    2016-07-01

    The purpose of this study was to evaluate whether adherence to the World Cancer Research Fund/American Institute for Cancer Research (WCRF/AICR) cancer prevention recommendations was associated with colorectal cancer incidence in the Black Women's Health Study (BWHS). In this ongoing prospective cohort of African American women (analytic cohort n = 49,103), 354 incident colorectal cancers were diagnosed between baseline (1995) and 2011. Adherence scores for seven WCRF/AICR recommendations (adherent = 1 point, non-adherent level 1 = 0.5 points, non-adherent level 2 = 0 points) were created using questionnaire data and summed to an overall adherence score (maximum = 7). Recommendation adherence and colorectal cancer incidence were evaluated using baseline and time-varying data in Cox regression models. At baseline, 8.5 % of women adhered >4 recommendations. In time-varying analyses, the HR was 0.98 (95 % CI 0.84-1.15) per 0.5 point higher score and 0.51 (95 % CI 0.23-1.10) for adherence to >4 compared to <3 recommendations. Adherence to individual recommendations was not associated with colorectal cancer risk. Results were similar in models that considered baseline exposures only. Adherence to cancer prevention recommendations was low and not associated with colorectal cancer risk among women in the BWHS. Research in diverse populations is essential to evaluate the validity of existing recommendations, and assess whether there are alternative recommendations that are more beneficial for cancer prevention in specific populations.

  11. Determination of toxic and essential element concentrations in foodstuffs from local market

    International Nuclear Information System (INIS)

    Surtipanti; Suwirma; Yumiarti; June, M.; Syaifudin, S.

    1989-01-01

    Determination of toxic and essential elements concentrations in foodstuffs from local market in Jakarta. Concentration of toxic essential elements, such as, As, Hg, Cr, Pb, Cu, and Zn, in rice, corn bean, small green peas, wheat, vegetables, fruits, tea and coffee, have been determined. As, Hg, Sb, Cr, Se, and Zn, were determined using neutron activation analysis, after being irradiated at TRIGA-MARK II reactor, while Pb and Cu were determined using atomic absorption spectrophotometer. The results obtained were lower than the maximum permissible concentration allowed. (author). 8 refs

  12. Recommender Systems for Learning

    CERN Document Server

    Manouselis, Nikos; Verbert, Katrien; Duval, Erik

    2013-01-01

    Technology enhanced learning (TEL) aims to design, develop and test sociotechnical innovations that will support and enhance learning practices of both individuals and organisations. It is therefore an application domain that generally covers technologies that support all forms of teaching and learning activities. Since information retrieval (in terms of searching for relevant learning resources to support teachers or learners) is a pivotal activity in TEL, the deployment of recommender systems has attracted increased interest. This brief attempts to provide an introduction to recommender systems for TEL settings, as well as to highlight their particularities compared to recommender systems for other application domains.

  13. Maximum entropy deconvolution of low count nuclear medicine images

    International Nuclear Information System (INIS)

    McGrath, D.M.

    1998-12-01

    Maximum entropy is applied to the problem of deconvolving nuclear medicine images, with special consideration for very low count data. The physics of the formation of scintigraphic images is described, illustrating the phenomena which degrade planar estimates of the tracer distribution. Various techniques which are used to restore these images are reviewed, outlining the relative merits of each. The development and theoretical justification of maximum entropy as an image processing technique is discussed. Maximum entropy is then applied to the problem of planar deconvolution, highlighting the question of the choice of error parameters for low count data. A novel iterative version of the algorithm is suggested which allows the errors to be estimated from the predicted Poisson mean values. This method is shown to produce the exact results predicted by combining Poisson statistics and a Bayesian interpretation of the maximum entropy approach. A facility for total count preservation has also been incorporated, leading to improved quantification. In order to evaluate this iterative maximum entropy technique, two comparable methods, Wiener filtering and a novel Bayesian maximum likelihood expectation maximisation technique, were implemented. The comparison of results obtained indicated that this maximum entropy approach may produce equivalent or better measures of image quality than the compared methods, depending upon the accuracy of the system model used. The novel Bayesian maximum likelihood expectation maximisation technique was shown to be preferable over many existing maximum a posteriori methods due to its simplicity of implementation. A single parameter is required to define the Bayesian prior, which suppresses noise in the solution and may reduce the processing time substantially. Finally, maximum entropy deconvolution was applied as a pre-processing step in single photon emission computed tomography reconstruction of low count data. Higher contrast results were

  14. Re-examining TG-142 recommendations in light of modern techniques for linear accelerator based radiosurgery.

    Science.gov (United States)

    Faught, Austin M; Trager, Michael; Yin, Fang-Fang; Kirkpatrick, John; Adamson, Justus

    2016-10-01

    The recent development of multifocal stereotactic radiosurgery (SRS) using a single isocenter volumetric modulated arc theory (VMAT) technique warrants a re-examination of the quality assurance (QA) tolerances for routine mechanical QA recommended by the American Association of Physicists in Medicine Task Group Report Number 142. Multifocal SRS can result in targets with small volumes being at a large off-axis distance from the treatment isocenter. Consequently, angular errors in the collimator, patient support assembly (PSA), or gantry could have an increased impact on target coverage. The authors performed a retrospective analysis of dose deviations caused by systematic errors in PSA, collimator, and gantry angle at the tolerance level for routine linear accelerator QA as recommended by TG-142. Dosimetric deviations from multifocal SRS plans (N = 10) were compared to traditional single target SRS using dynamic conformal arcs (N = 10). The chief dosimetric quantities used in determining clinical impact were V 100% and D 99% of the individual planning target volumes and V 12Gy of the healthy brain. Induced errors at tolerance levels showed the greatest change in multifocal SRS target coverage for collimator rotations (±1.0°) with the average changes to V 100% and D 99% being 5% and 6%, respectively, with maximum changes of 33% and 20%. A reduction in the induced error to half the TG-142 tolerance (±0.5°) demonstrated similar changes in coverage loss to traditional single target SRS assessed at the recommended tolerance level. The observed change in coverage for multifocal SRS was reduced for gantry errors (±1.0°) at 2% and 4.5% for V 100% and D 99% , respectively, with maximum changes of 18% and 12%. Minimal change in coverage was noted for errors in PSA rotation. This study indicates that institutions utilizing a single isocenter VMAT technique for multifocal disease should pay careful attention to the angular mechanical tolerances in designing a robust and

  15. Carbon dioxide concentrations are very high in developing oilseeds.

    Science.gov (United States)

    Goffman, Fernando D; Ruckle, Mike; Ohlrogge, John; Shachar-Hill, Yair

    2004-09-01

    A new method has been developed to rapidly determine the total inorganic carbon concentration (gaseous [CO2] + aqueous [CO(2)] + [HCO3-] + [CO3(2)-]) in developing seeds. Seeds are rapidly dissected and homogenized in 1 N HCl in gas-tight vials. The headspace gas is then analyzed by infrared gas analysis. Developing rapeseed (Brassica napus L.) and soybean [Glycine max (L.) Merr.] seeds were analyzed and found to have up to 40 and 12 mM total inorganic carbon, respectively. These concentrations are ca. 600-2000-fold higher than in ambient air or values reported for leaves. Carbon dioxide concentrations in rapeseed peaked during the stage of maximum oil synthesis and declined as seeds matured. The consequences for seed metabolism, physiology and carbon economy are discussed.

  16. Development of total maximum daily loads for bacteria impaired watershed using the comprehensive hydrology and water quality simulation model.

    Science.gov (United States)

    Kim, Sang M; Brannan, Kevin M; Zeckoski, Rebecca W; Benham, Brian L

    2014-01-01

    The objective of this study was to develop bacteria total maximum daily loads (TMDLs) for the Hardware River watershed in the Commonwealth of Virginia, USA. The TMDL program is an integrated watershed management approach required by the Clean Water Act. The TMDLs were developed to meet Virginia's water quality standard for bacteria at the time, which stated that the calendar-month geometric mean concentration of Escherichia coli should not exceed 126 cfu/100 mL, and that no single sample should exceed a concentration of 235 cfu/100 mL. The bacteria impairment TMDLs were developed using the Hydrological Simulation Program-FORTRAN (HSPF). The hydrology and water quality components of HSPF were calibrated and validated using data from the Hardware River watershed to ensure that the model adequately simulated runoff and bacteria concentrations. The calibrated and validated HSPF model was used to estimate the contributions from the various bacteria sources in the Hardware River watershed to the in-stream concentration. Bacteria loads were estimated through an extensive source characterization process. Simulation results for existing conditions indicated that the majority of the bacteria came from livestock and wildlife direct deposits and pervious lands. Different source reduction scenarios were evaluated to identify scenarios that meet both the geometric mean and single sample maximum E. coli criteria with zero violations. The resulting scenarios required extreme and impractical reductions from livestock and wildlife sources. Results from studies similar to this across Virginia partially contributed to a reconsideration of the standard's applicability to TMDL development.

  17. Liver iron concentration quantification by MRI: are recommended protocols accurate enough for clinical practice?

    International Nuclear Information System (INIS)

    Castiella, Agustin; Zapata, Eva Mia; Alustiza, Jose M.; Emparanza, Jose I.; Costero, Belen; Diez, Maria I.

    2011-01-01

    To assess the accuracy of quantification of liver iron concentration (LIC) by MRI using the Rennes University (URennes) algorithm. In the overall study period 1999-2006 the LIC in 171 patients was calculated with the URennes model and the results were compared with LIC measured by liver biopsy. The biopsy showed that 107 patients had no overload, 38 moderate overload and 26 high overload. The correlation between MRI and biopsy was r = 0.86. MRI correctly classified 105 patients according to the various levels of LIC. Diagnostic accuracy was 61.4%, with a tendency to overestimate overload: 43% of patients with no overload were diagnosed as having overload, and 44.7% of patients with moderate overload were diagnosed as having high overload. The sensitivity of the URennes method for high overload was 92.3%, and the specificity for the absence of overload was 57.0%. MRI values greater than 170 μmol Fe/g revealed a positive predictive value (PPV) for haemochromatosis of 100% (n = 18); concentrations below 60 μmol Fe/g had a negative predictive value (NPV) of 100% for haemochromatosis (n = 101). The diagnosis in 44 patients with intermediate values remained uncertain. The assessment of LIC with the URennes method was useful in 74.3% of the patients to rule out or to diagnose high iron overload. The method has a tendency to overestimate overload, which limits its diagnostic performance. (orig.)

  18. Liver iron concentration quantification by MRI: are recommended protocols accurate enough for clinical practice?

    Energy Technology Data Exchange (ETDEWEB)

    Castiella, Agustin; Zapata, Eva M. [Mendaro Hospital, Gastroenterology Service, Mendaro (Spain); Alustiza, Jose M. [Osatek Donostia, Radiology Service, Donostia (Spain); Emparanza, Jose I. [Donostia Hospital CASPe, CIBER-ESP, Clinical Epidemiology Unit, Donostia (Spain); Costero, Belen [Principe de Asturias Hospital, Gastroenterology Service, Alcala de Henares (Spain); Diez, Maria I. [Principe de Asturias Hospital, Radiology Service, Alcala de Henares (Spain)

    2011-01-15

    To assess the accuracy of quantification of liver iron concentration (LIC) by MRI using the Rennes University (URennes) algorithm. In the overall study period 1999-2006 the LIC in 171 patients was calculated with the URennes model and the results were compared with LIC measured by liver biopsy. The biopsy showed that 107 patients had no overload, 38 moderate overload and 26 high overload. The correlation between MRI and biopsy was r = 0.86. MRI correctly classified 105 patients according to the various levels of LIC. Diagnostic accuracy was 61.4%, with a tendency to overestimate overload: 43% of patients with no overload were diagnosed as having overload, and 44.7% of patients with moderate overload were diagnosed as having high overload. The sensitivity of the URennes method for high overload was 92.3%, and the specificity for the absence of overload was 57.0%. MRI values greater than 170 {mu}mol Fe/g revealed a positive predictive value (PPV) for haemochromatosis of 100% (n = 18); concentrations below 60 {mu}mol Fe/g had a negative predictive value (NPV) of 100% for haemochromatosis (n = 101). The diagnosis in 44 patients with intermediate values remained uncertain. The assessment of LIC with the URennes method was useful in 74.3% of the patients to rule out or to diagnose high iron overload. The method has a tendency to overestimate overload, which limits its diagnostic performance. (orig.)

  19. Recommendations for radioembolisation after liver surgery using yttrium-90 resin microspheres based on a survey of an international expert panel

    International Nuclear Information System (INIS)

    Samim, Morsal; Veenendaal, Linde M. van; Braat, Manon N.G.J.A.; Hoven, Andor F. van den; Bosch, Maurice A.A.J. van den; Lam, Marnix G.E.H.; Hillegersberg, Richard van; Sangro, Bruno; Kao, Yung Hsiang; Liu, Dave; Louie, John D.; Sze, Daniel Y.; Rose, Steven C.; Brown, Daniel B.; Ahmadzadehfar, Hojjat; Kim, Edward

    2017-01-01

    Guidelines on how to adjust activity in patients with a history of liver surgery who are undergoing yttrium-90 radioembolisation ( 90 Y-RE) are lacking. The aim was to study the variability in activity prescription in these patients, between centres with extensive experience using resin microspheres 90 Y-RE, and to draw recommendations on activity prescription based on an expert consensus. The variability in activity prescription between centres was investigated by a survey of international experts in the field of 90 Y-RE. Six representative post-surgical patients (i.e. comparable activity prescription, different outcome) were selected. Information on patients' disease characteristics and data needed for activity calculation was presented to the expert panel. Reported was the used method for activity prescription and whether, how and why activity reduction was found indicated. Ten experts took part in the survey. Recommendations on activity reduction were highly variable between the expert panel. The median intra-patient range was 44 Gy (range 18-55 Gy). Reductions in prescribed activity were recommended in 68% of the cases. In consensus, a maximum D Target of 50 Gy was recommended. With a current lack of guidelines, large variability in activity prescription in post-surgical patients undergoing 90 Y-RE exists. In consensus, D Target ≤50 Gy is recommended. (orig.)

  20. Maximum Principles for Discrete and Semidiscrete Reaction-Diffusion Equation

    Directory of Open Access Journals (Sweden)

    Petr Stehlík

    2015-01-01

    Full Text Available We study reaction-diffusion equations with a general reaction function f on one-dimensional lattices with continuous or discrete time ux′  (or  Δtux=k(ux-1-2ux+ux+1+f(ux, x∈Z. We prove weak and strong maximum and minimum principles for corresponding initial-boundary value problems. Whereas the maximum principles in the semidiscrete case (continuous time exhibit similar features to those of fully continuous reaction-diffusion model, in the discrete case the weak maximum principle holds for a smaller class of functions and the strong maximum principle is valid in a weaker sense. We describe in detail how the validity of maximum principles depends on the nonlinearity and the time step. We illustrate our results on the Nagumo equation with the bistable nonlinearity.

  1. Minimal length, Friedmann equations and maximum density

    Energy Technology Data Exchange (ETDEWEB)

    Awad, Adel [Center for Theoretical Physics, British University of Egypt,Sherouk City 11837, P.O. Box 43 (Egypt); Department of Physics, Faculty of Science, Ain Shams University,Cairo, 11566 (Egypt); Ali, Ahmed Farag [Centre for Fundamental Physics, Zewail City of Science and Technology,Sheikh Zayed, 12588, Giza (Egypt); Department of Physics, Faculty of Science, Benha University,Benha, 13518 (Egypt)

    2014-06-16

    Inspired by Jacobson’s thermodynamic approach, Cai et al. have shown the emergence of Friedmann equations from the first law of thermodynamics. We extend Akbar-Cai derivation http://dx.doi.org/10.1103/PhysRevD.75.084003 of Friedmann equations to accommodate a general entropy-area law. Studying the resulted Friedmann equations using a specific entropy-area law, which is motivated by the generalized uncertainty principle (GUP), reveals the existence of a maximum energy density closed to Planck density. Allowing for a general continuous pressure p(ρ,a) leads to bounded curvature invariants and a general nonsingular evolution. In this case, the maximum energy density is reached in a finite time and there is no cosmological evolution beyond this point which leaves the big bang singularity inaccessible from a spacetime prospective. The existence of maximum energy density and a general nonsingular evolution is independent of the equation of state and the spacial curvature k. As an example we study the evolution of the equation of state p=ωρ through its phase-space diagram to show the existence of a maximum energy which is reachable in a finite time.

  2. Maximum-Entropy Inference with a Programmable Annealer

    Science.gov (United States)

    Chancellor, Nicholas; Szoke, Szilard; Vinci, Walter; Aeppli, Gabriel; Warburton, Paul A.

    2016-03-01

    Optimisation problems typically involve finding the ground state (i.e. the minimum energy configuration) of a cost function with respect to many variables. If the variables are corrupted by noise then this maximises the likelihood that the solution is correct. The maximum entropy solution on the other hand takes the form of a Boltzmann distribution over the ground and excited states of the cost function to correct for noise. Here we use a programmable annealer for the information decoding problem which we simulate as a random Ising model in a field. We show experimentally that finite temperature maximum entropy decoding can give slightly better bit-error-rates than the maximum likelihood approach, confirming that useful information can be extracted from the excited states of the annealer. Furthermore we introduce a bit-by-bit analytical method which is agnostic to the specific application and use it to show that the annealer samples from a highly Boltzmann-like distribution. Machines of this kind are therefore candidates for use in a variety of machine learning applications which exploit maximum entropy inference, including language processing and image recognition.

  3. Mercury concentrations in snapping turtles (Chelydra serpentina) correlate with environmental and landscape characteristics.

    Science.gov (United States)

    Turnquist, Madeline A; Driscoll, Charles T; Schulz, Kimberly L; Schlaepfer, Martin A

    2011-10-01

    Mercury (Hg) deposited onto the landscape can be transformed into methylmercury (MeHg), a neurotoxin that bioaccumulates up the aquatic food chain. Here, we report on Hg concentrations in snapping turtles (Chelydra serpentina) across New York State, USA. The objectives of this study were to: (1) test which landscape, water, and biometric characteristics correlate with total Hg (THg) concentrations in snapping turtles; and (2) determine whether soft tissue THg concentrations correlate with scute (shell) concentrations. Forty-eight turtles were sampled non-lethally from ten lakes and wetlands across New York to observe patterns under a range of ecosystem variables and water chemistry conditions. THg concentrations ranged from 0.041 to 1.50 μg/g and 0.47 to 7.43 μg/g wet weight of muscle tissue and shell, respectively. The vast majority of mercury (~94%) was in the MeHg form. Sixty-one percent of turtle muscle samples exceeded U.S. Environmental Protection Agency (U.S. EPA) consumption advisory limit of 0.3 μg Hg/g for fish. Muscle THg concentrations were significantly correlated with sulfate in water and the maximum elevation of the watershed. Shell THg concentrations were significantly correlated with the acid neutralizing capacity (ANC) of water, the maximum elevation of the watershed, the percent open water in the watershed, the lake to watershed size, and various forms of atmospheric Hg deposition. Thus, our results demonstrate that THg concentrations in snapping turtles are spatially variable, frequently exceed advisory limits, and are significantly correlated with several landscape and water characteristics.

  4. Probabilistic maximum-value wind prediction for offshore environments

    DEFF Research Database (Denmark)

    Staid, Andrea; Pinson, Pierre; Guikema, Seth D.

    2015-01-01

    statistical models to predict the full distribution of the maximum-value wind speeds in a 3 h interval. We take a detailed look at the performance of linear models, generalized additive models and multivariate adaptive regression splines models using meteorological covariates such as gust speed, wind speed......, convective available potential energy, Charnock, mean sea-level pressure and temperature, as given by the European Center for Medium-Range Weather Forecasts forecasts. The models are trained to predict the mean value of maximum wind speed, and the residuals from training the models are used to develop...... the full probabilistic distribution of maximum wind speed. Knowledge of the maximum wind speed for an offshore location within a given period can inform decision-making regarding turbine operations, planned maintenance operations and power grid scheduling in order to improve safety and reliability...

  5. Error exponents for entanglement concentration

    International Nuclear Information System (INIS)

    Hayashi, Masahito; Koashi, Masato; Matsumoto, Keiji; Morikoshi, Fumiaki; Winter, Andreas

    2003-01-01

    Consider entanglement concentration schemes that convert n identical copies of a pure state into a maximally entangled state of a desired size with success probability being close to one in the asymptotic limit. We give the distillable entanglement, the number of Bell pairs distilled per copy, as a function of an error exponent, which represents the rate of decrease in failure probability as n tends to infinity. The formula fills the gap between the least upper bound of distillable entanglement in probabilistic concentration, which is the well-known entropy of entanglement, and the maximum attained in deterministic concentration. The method of types in information theory enables the detailed analysis of the distillable entanglement in terms of the error rate. In addition to the probabilistic argument, we consider another type of entanglement concentration scheme, where the initial state is deterministically transformed into a (possibly mixed) final state whose fidelity to a maximally entangled state of a desired size converges to one in the asymptotic limit. We show that the same formula as in the probabilistic argument is valid for the argument on fidelity by replacing the success probability with the fidelity. Furthermore, we also discuss entanglement yield when optimal success probability or optimal fidelity converges to zero in the asymptotic limit (strong converse), and give the explicit formulae for those cases

  6. Clinical practice recommendations for depression.

    Science.gov (United States)

    Malhi, G S; Adams, D; Porter, R; Wignall, A; Lampe, L; O'Connor, N; Paton, M; Newton, L A; Walter, G; Taylor, A; Berk, M; Mulder, R T

    2009-01-01

    To provide clinically relevant evidence-based recommendations for the management of depression in adults that are informative, easy to assimilate and facilitate clinical decision making. A comprehensive literature review of over 500 articles was undertaken using electronic database search engines (e.g. MEDLINE, PsychINFO and Cochrane reviews). In addition articles, book chapters and other literature known to the authors were reviewed. The findings were then formulated into a set of recommendations that were developed by a multidisciplinary team of clinicians who routinely deal with mood disorders. The recommendations then underwent consultative review by a broader advisory panel that included experts in the field, clinical staff and patient representatives. The clinical practice recommendations for depression (Depression CPR) summarize evidence-based treatments and provide a synopsis of recommendations relating to each phase of the illness. They are designed for clinical use and have therefore been presented succinctly in an innovative and engaging manner that is clear and informative. These up-to-date recommendations provide an evidence-based framework that incorporates clinical wisdom and consideration of individual factors in the management of depression. Further, the novel style and practical approach should promote uptake and implementation.

  7. Characterizing graphs of maximum matching width at most 2

    DEFF Research Database (Denmark)

    Jeong, Jisu; Ok, Seongmin; Suh, Geewon

    2017-01-01

    The maximum matching width is a width-parameter that is de ned on a branch-decomposition over the vertex set of a graph. The size of a maximum matching in the bipartite graph is used as a cut-function. In this paper, we characterize the graphs of maximum matching width at most 2 using the minor o...

  8. New Insulin Delivery Recommendations.

    Science.gov (United States)

    Frid, Anders H; Kreugel, Gillian; Grassi, Giorgio; Halimi, Serge; Hicks, Debbie; Hirsch, Laurence J; Smith, Mike J; Wellhoener, Regine; Bode, Bruce W; Hirsch, Irl B; Kalra, Sanjay; Ji, Linong; Strauss, Kenneth W

    2016-09-01

    Many primary care professionals manage injection or infusion therapies in patients with diabetes. Few published guidelines have been available to help such professionals and their patients manage these therapies. Herein, we present new, practical, and comprehensive recommendations for diabetes injections and infusions. These recommendations were informed by a large international survey of current practice and were written and vetted by 183 diabetes experts from 54 countries at the Forum for Injection Technique and Therapy: Expert Recommendations (FITTER) workshop held in Rome, Italy, in 2015. Recommendations are organized around the themes of anatomy, physiology, pathology, psychology, and technology. Key among the recommendations are that the shortest needles (currently the 4-mm pen and 6-mm syringe needles) are safe, effective, and less painful and should be the first-line choice in all patient categories; intramuscular injections should be avoided, especially with long-acting insulins, because severe hypoglycemia may result; lipohypertrophy is a frequent complication of therapy that distorts insulin absorption, and, therefore, injections and infusions should not be given into these lesions and correct site rotation will help prevent them; effective long-term therapy with insulin is critically dependent on addressing psychological hurdles upstream, even before insulin has been started; inappropriate disposal of used sharps poses a risk of infection with blood-borne pathogens; and mitigation is possible with proper training, effective disposal strategies, and the use of safety devices. Adherence to these new recommendations should lead to more effective therapies, improved outcomes, and lower costs for patients with diabetes. Copyright © 2016 Mayo Foundation for Medical Education and Research. Published by Elsevier Inc. All rights reserved.

  9. Stress Concentration Factor of Expanded Aluminum Tubes Using Finite Element Modeling

    Directory of Open Access Journals (Sweden)

    L Mhamdi

    2013-06-01

    Full Text Available This paper discusses the development of semi-empirical relations for the maximum stress concentration factor (SCF around circular holes embedded in aluminum tubes under various expansion ratios and mandrel angles. Finite element models were developed to study the expansion of a typical aluminum tube with embedded holes of various sizes. An elastic perfectly-plastic material behaviour was used to describe the structural response of the tubes under expansion. Various hole-diameter-to-tubewall- thickness ratios, tube expansion ratios, and mandrel angles were considered to determine the stress state around the hole at zero and 90 degree locations from which the maximum SCF was determined. Semi-empirical relations for the maximum SCF using the Lagrange interpolation formulation were developed. The developed relations were found to predict the SCFs accurately.

  10. Radiocesium concentrations of snakes from contaminated and non-contaminated habitats of the AEC Savannah River Plant

    International Nuclear Information System (INIS)

    Brisbin, I.L. Jr.; Staton, M.A.; Pinder, J.E. III.; Geiger, R.A.

    1974-01-01

    Concentration levels of 134 Cs and 137 Cs were determined for 117 snakes of 19 species collected on the AEC Savannah River Plant near Aiken, South Carolina. Snakes collected from the vicinity of a reactor effluent stream averaged 131.5 pCi radiocesium/g live weight, with a maximum of 1032.6 pCi/g, and represented the highest level of radiocesium concentration reported in the literature for any naturally-occurring wild population of vertebrate predators. These snakes had significantly higher concentrations of radiocesium than those collected in the vicinity of a reactor cooling reservoir which averaged 27.7 pCi/g live weight, with a maximum of 139.3 pCi/g. The radiocesium contents of snakes collected from uncontaminated habitats averaged 2.6 and 2.4 pCi/g live weight, respectively, and did not differ significantly from background radiation levels. Radiocesium concentrations approximated a log-normal frequency distribution, and no significant differences in frequency-distribution patterns could be demonstrated between collection areas. (U.S.)

  11. Influence of source type and air exchange on variations of indoor radon concentration

    International Nuclear Information System (INIS)

    Arvela, H.; Winqvist, K.

    1986-04-01

    The model relates radon concentration to source strength and its variations, air exchange rate and meteorological factors. Two types of sources have been studied. The pressure difference dependent source is made up of radon transported with soil pore air and driven by pressure difference due to the stack effect. The constant source is made up of radon transported by diffusion from building materials or from soil. The air exchange rate depends exponentially on indoor-outdoor temperature difference and linearly on wind speed. These two inputs have been summed in quadrature. In a house with a constant source radon concentration decreases when the air exchange rate increases due to the increasing temperature difference, whereas the pressure difference dependent source causes an increasing concentration. This is due to the fact that the effect of the source strength increase is stronger than the decreasing effect of air exchange on concentration. The winter-summer concentration ratio depends on the combination of the two types of source. A pure pressure dependent source leads to the winter-summer ratio of 2-3.5 (winter -5 deg C, summer +15 deg C, wind speed 3 m/s). A strong contribution of a constant source is needed to cause a summer concentration higher than the winter concentration. The model is in agreement with the winter-summer concentration ratios measured. This ratio increases with the increasing winter concentration. The measured ratio was near 1.0 for houses with winter concentration of 200 Bq m''3 or less and near 2.0 with concentration of 1000 Bq m''3. In a house with a constant source, the diurnal maximum occurs in the afternoon, while in houses with a pressure difference dependent source the time of maximum is early in the morning

  12. The Maximum Resource Bin Packing Problem

    DEFF Research Database (Denmark)

    Boyar, J.; Epstein, L.; Favrholdt, L.M.

    2006-01-01

    Usually, for bin packing problems, we try to minimize the number of bins used or in the case of the dual bin packing problem, maximize the number or total size of accepted items. This paper presents results for the opposite problems, where we would like to maximize the number of bins used...... algorithms, First-Fit-Increasing and First-Fit-Decreasing for the maximum resource variant of classical bin packing. For the on-line variant, we define maximum resource variants of classical and dual bin packing. For dual bin packing, no on-line algorithm is competitive. For classical bin packing, we find...

  13. Maximum entropy analysis of EGRET data

    DEFF Research Database (Denmark)

    Pohl, M.; Strong, A.W.

    1997-01-01

    EGRET data are usually analysed on the basis of the Maximum-Likelihood method \\cite{ma96} in a search for point sources in excess to a model for the background radiation (e.g. \\cite{hu97}). This method depends strongly on the quality of the background model, and thus may have high systematic unce...... uncertainties in region of strong and uncertain background like the Galactic Center region. Here we show images of such regions obtained by the quantified Maximum-Entropy method. We also discuss a possible further use of MEM in the analysis of problematic regions of the sky....

  14. Density estimation by maximum quantum entropy

    International Nuclear Information System (INIS)

    Silver, R.N.; Wallstrom, T.; Martz, H.F.

    1993-01-01

    A new Bayesian method for non-parametric density estimation is proposed, based on a mathematical analogy to quantum statistical physics. The mathematical procedure is related to maximum entropy methods for inverse problems and image reconstruction. The information divergence enforces global smoothing toward default models, convexity, positivity, extensivity and normalization. The novel feature is the replacement of classical entropy by quantum entropy, so that local smoothing is enforced by constraints on differential operators. The linear response of the estimate is proportional to the covariance. The hyperparameters are estimated by type-II maximum likelihood (evidence). The method is demonstrated on textbook data sets

  15. Hybrid recommendation methods in complex networks.

    Science.gov (United States)

    Fiasconaro, A; Tumminello, M; Nicosia, V; Latora, V; Mantegna, R N

    2015-07-01

    We propose two recommendation methods, based on the appropriate normalization of already existing similarity measures, and on the convex combination of the recommendation scores derived from similarity between users and between objects. We validate the proposed measures on three data sets, and we compare the performance of our methods to other recommendation systems recently proposed in the literature. We show that the proposed similarity measures allow us to attain an improvement of performances of up to 20% with respect to existing nonparametric methods, and that the accuracy of a recommendation can vary widely from one specific bipartite network to another, which suggests that a careful choice of the most suitable method is highly relevant for an effective recommendation on a given system. Finally, we study how an increasing presence of random links in the network affects the recommendation scores, finding that one of the two recommendation algorithms introduced here can systematically outperform the others in noisy data sets.

  16. Trends of atmospheric black carbon concentration over the United Kingdom

    Science.gov (United States)

    Singh, Vikas; Ravindra, Khaiwal; Sahu, Lokesh; Sokhi, Ranjeet

    2018-04-01

    The continuous observations over a period of 7 years (2009-2016) available at 7 locations show declining trend of atmospheric BC in the UK. Among all the locations, the highest decrease of 8 ± 3 percent per year was observed at the Marylebone road in London. The detailed analysis performed at 21 locations during 2009-2011 shows that average annual mean atmospheric BC concentration were 0.45 ± 0.10, 1.47 ± 0.58, 1.34 ± 0.31, 1.83 ± 0.46 and 9.72 ± 0.78 μgm-3 at rural, suburban, urban background, urban centre and kerbside sites respectively. Around 1 μgm-3 of atmospheric BC could be attributed to urban emission, whereas traffic contributed up to 8 μg m-3 of atmospheric BC near busy roads. Seasonal pattern was also observed at all locations except rural and kerbside location, with maximum concentrations (1.2-4 μgm-3) in winter. Further, minimum concentrations (0.3-1.2 μgm-3) were observed in summer and similar concentrations in spring and fall. At suburban and urban background locations, similar diurnal pattern were observed with atmospheric BC concentration peaks (≈1.8 μg m-3) in the morning (around 9 a.m.) and evening (7-9 p.m.) rush hours, whereas minimum concentrations were during late night hours (peak at 5 a.m.) and the afternoon hours (peak at 2 p.m.). The urban centre values show a similar morning pattern (peak at 9 a.m.; concentration - 2.5 μgm-3) in relation to background locations but only a slight decrease in concentration in the afternoon which remained above 2 μgm-3 till midnight. It is concluded that the higher flow of traffic at urban centre locations results in higher atmospheric BC concentrations throughout the day. Comparison of weekday and weekend daily averaged atmospheric BC showed maximum concentrations on Friday, having minimum levels on Sunday. This study will help to refine the atmospheric BC emission inventories and provide data for air pollution and climate change models evaluation, which are used to formulate air pollution

  17. Scientific white paper on concentration-QTc modeling.

    Science.gov (United States)

    Garnett, Christine; Bonate, Peter L; Dang, Qianyu; Ferber, Georg; Huang, Dalong; Liu, Jiang; Mehrotra, Devan; Riley, Steve; Sager, Philip; Tornoe, Christoffer; Wang, Yaning

    2018-06-01

    The International Council for Harmonisation revised the E14 guideline through the questions and answers process to allow concentration-QTc (C-QTc) modeling to be used as the primary analysis for assessing the QTc interval prolongation risk of new drugs. A well-designed and conducted QTc assessment based on C-QTc modeling in early phase 1 studies can be an alternative approach to a thorough QT study for some drugs to reliably exclude clinically relevant QTc effects. This white paper provides recommendations on how to plan and conduct a definitive QTc assessment of a drug using C-QTc modeling in early phase clinical pharmacology and thorough QT studies. Topics included are: important study design features in a phase 1 study; modeling objectives and approach; exploratory plots; the pre-specified linear mixed effects model; general principles for model development and evaluation; and expectations for modeling analysis plans and reports. The recommendations are based on current best modeling practices, scientific literature and personal experiences of the authors. These recommendations are expected to evolve as their implementation during drug development provides additional data and with advances in analytical methodology.

  18. Limits to anaerobic energy and cytosolic concentration in the living cell

    Science.gov (United States)

    Paglietti, A.

    2015-11-01

    For many physical systems at any given temperature, the set of all states where the system's free energy reaches its largest value can be determined from the system's constitutive equations of internal energy and entropy, once a state of that set is known. Such an approach is fraught with complications when applied to a living cell, because the cell's cytosol contains thousands of solutes, and thus thousands of state variables, which makes determination of its state impractical. We show here that, when looking for the maximum energy that the cytosol can store and release, detailed information on cytosol composition is redundant. Compatibility with cell's life requires that a single variable that represents the overall concentration of cytosol solutes must fall between defined limits, which can be determined by dehydrating and overhydrating the cell to its maximum capacity. The same limits are shown to determine, in particular, the maximum amount of free energy that a cell can supply in fast anaerobic processes, starting from any given initial state. For a typical skeletal muscle in normal physiological conditions this energy, i.e., the maximum anaerobic capacity to do work, is calculated to be about 960 J per kg of muscular mass. Such energy decreases as the overall concentration of solutes in the cytosol is increased. Similar results apply to any kind of cell. They provide an essential tool to understand and control the macroscopic response of single cells and multicellular cellular tissues alike. The applications include sport physiology, cell aging, disease produced cell damage, drug absorption capacity, to mention the most obvious ones.

  19. Tomato yield and potassium concentrations in soil and in plant petioles as affected by potassium fertirrigation

    Directory of Open Access Journals (Sweden)

    FONTES PAULO CEZAR REZENDE

    2000-01-01

    Full Text Available Tomato (Lycopersicon esculentum Mill. cv. Santa Clara was grown on a silt clay soil with 46 mg dm-3 Mehlich 1 extractable K, to evaluate the effects of trickle-applied K rates on fruit yield and to establish K critical concentrations in soil and in plant petioles. Six potassium rates (0, 48, 119, 189, 259 and 400 kg ha-1 K were applied in a randomized complete block design with four replications. Soil and plant K critical levels were determined at two plant growth stages (at the beginning of the second and fourth cluster flowering. Total, marketable and weighted yields increased with K rates, reaching their maximum of 86.4, 73.4, and 54.9 ton ha-1 at 198, 194, and 125 kg ha-1 K , respectively. At the first soil sampling date K critical concentrations in the soil associated with K rates for maximum marketable and weighted yields were 92 and 68 mg dm-3, respectively. Potassium critical concentrations in the dry matter of the petioles sampled by the beginning of the second and fourth cluster flowering time, associated with maximum weighted yield, were 10.30 and 7.30 dag kg-1, respectively.

  20. Last Glacial Maximum Salinity Reconstruction

    Science.gov (United States)

    Homola, K.; Spivack, A. J.

    2016-12-01

    It has been previously demonstrated that salinity can be reconstructed from sediment porewater. The goal of our study is to reconstruct high precision salinity during the Last Glacial Maximum (LGM). Salinity is usually determined at high precision via conductivity, which requires a larger volume of water than can be extracted from a sediment core, or via chloride titration, which yields lower than ideal precision. It has been demonstrated for water column samples that high precision density measurements can be used to determine salinity at the precision of a conductivity measurement using the equation of state of seawater. However, water column seawater has a relatively constant composition, in contrast to porewater, where variations from standard seawater composition occur. These deviations, which affect the equation of state, must be corrected for through precise measurements of each ion's concentration and knowledge of apparent partial molar density in seawater. We have developed a density-based method for determining porewater salinity that requires only 5 mL of sample, achieving density precisions of 10-6 g/mL. We have applied this method to porewater samples extracted from long cores collected along a N-S transect across the western North Atlantic (R/V Knorr cruise KN223). Density was determined to a precision of 2.3x10-6 g/mL, which translates to salinity uncertainty of 0.002 gms/kg if the effect of differences in composition is well constrained. Concentrations of anions (Cl-, and SO4-2) and cations (Na+, Mg+, Ca+2, and K+) were measured. To correct salinities at the precision required to unravel LGM Meridional Overturning Circulation, our ion precisions must be better than 0.1% for SO4-/Cl- and Mg+/Na+, and 0.4% for Ca+/Na+, and K+/Na+. Alkalinity, pH and Dissolved Inorganic Carbon of the porewater were determined to precisions better than 4% when ratioed to Cl-, and used to calculate HCO3-, and CO3-2. Apparent partial molar densities in seawater were