Economic total maximum daily load for watershed-based pollutant trading.

Science.gov (United States)

Zaidi, A Z; deMonsabert, S M

2015-04-01

Water quality trading (WQT) is supported by the US Environmental Protection Agency (USEPA) under the framework of its total maximum daily load (TMDL) program. An innovative approach is presented in this paper that proposes post-TMDL trade by calculating pollutant rights for each pollutant source within a watershed. Several water quality trading programs are currently operating in the USA with an objective to achieve overall pollutant reduction impacts that are equivalent or better than TMDL scenarios. These programs use trading ratios for establishing water quality equivalence among pollutant reductions. The inbuilt uncertainty in modeling the effects of pollutants in a watershed from both the point and nonpoint sources on receiving waterbodies makes WQT very difficult. A higher trading ratio carries with it increased mitigation costs, but cannot ensure the attainment of the required water quality with certainty. The selection of an applicable trading ratio, therefore, is not a simple process. The proposed approach uses an Economic TMDL optimization model that determines an economic pollutant reduction scenario that can be compared with actual TMDL allocations to calculate selling/purchasing rights for each contributing source. The methodology is presented using the established TMDLs for the bacteria (fecal coliform) impaired Muddy Creek subwatershed WAR1 in Rockingham County, Virginia, USA. Case study results show that an environmentally and economically superior trading scenario can be realized by using Economic TMDL model or any similar model that considers the cost of TMDL allocations.

Variability of Surface pollutants and aerosol concentration over Abu Dhabi, UAE - sources, transport and current levels

Science.gov (United States)

Phanikumar, Devulapalli V.; Basha, Ghouse; Ouarda, Taha B. M. J.

2015-04-01

In the view of recent economic, industrial, and rapid development, Abu Dhabi (24.4oN; 54.4oE; 27m msl) has become one of the most populated regions in the world despite of extreme heat, frequent dust storms, and with distinctive topography. The major sources of air pollution are from the dust and sand storms, greenhouse gas emissions, and to some extent from industrial pollution. In order to realize the accurate and comprehensive understanding of air quality and plausible sources over this region, we have made a detailed analysis of three years simultaneous measurements during 2011-13 of pollutants such as O3, SO2, NO2, CO, and PM10 concentrations. Diurnal variation of meteorological parameters such as temperature and wind speed/relative humidity clearly shows daytime maximum/minimum in summer followed by pre-monsoon, post-monsoon and winter. The prevailing winds over this region are mostly from northwesterly direction (Shamal wind). Diurnal wind pattern showed a clear contrast with the majority of the wind pattern during nighttime and early morning is from the westerly/northwesterly and daytime is from southwesterly/southeasterly directions. The diurnal pattern of O3 shows minimum during 08 LT and increases thereafter reaching maximum at 17 LT and decreases during nighttime. However, the diurnal pattern of SO2 and NO2 show a peak at ~ 08 LT and dip at ~ 14 LT during all the seasons with some variability in each season. On the other hand, the diurnal pattern of CO shows a peculiar picture of elevated levels during daytime peaking at ~ 10 LT (prominent in summer and post-monsoon) followed by a sharp decrease and minimum is ~14 LT. PM10 concentration has an early morning peak at ~ 02 LT and then decreases to a minimum value at ~11 LT and again increases in the afternoon hours (maximum at ~17 LT) depicting a forenoon-afternoon asymmetry. Monthly variation of PM10 shows maximum in pre-monsoon season and minimum in winter. Our observations show the diurnal pattern of

Fractional kalman filter to estimate the concentration of air pollution

Science.gov (United States)

Vita Oktaviana, Yessy; Apriliani, Erna; Khusnul Arif, Didik

2018-04-01

Air pollution problem gives important effect in quality environment and quality of human’s life. Air pollution can be caused by nature sources or human activities. Pollutant for example Ozone, a harmful gas formed by NOx and volatile organic compounds (VOCs) emitted from various sources. The air pollution problem can be modeled by TAPM-CTM (The Air Pollution Model with Chemical Transport Model). The model shows concentration of pollutant in the air. Therefore, it is important to estimate concentration of air pollutant. Estimation method can be used for forecast pollutant concentration in future and keep stability of air quality. In this research, an algorithm is developed, based on Fractional Kalman Filter to solve the model of air pollution’s problem. The model will be discretized first and then it will be estimated by the method. The result shows that estimation of Fractional Kalman Filter has better accuracy than estimation of Kalman Filter. The accuracy was tested by applying RMSE (Root Mean Square Error).

Total maximum allocated load calculation of nitrogen pollutants by linking a 3D biogeochemical-hydrodynamic model with a programming model in Bohai Sea

Science.gov (United States)

Dai, Aiquan; Li, Keqiang; Ding, Dongsheng; Li, Yan; Liang, Shengkang; Li, Yanbin; Su, Ying; Wang, Xiulin

2015-12-01

The equal percent removal (EPR) method, in which pollutant reduction ratio was set as the same in all administrative regions, failed to satisfy the requirement for water quality improvement in the Bohai Sea. Such requirement was imposed by the developed Coastal Pollution Total Load Control Management. The total maximum allocated load (TMAL) of nitrogen pollutants in the sea-sink source regions (SSRs) around the Bohai Rim, which is the maximum pollutant load of every outlet under the limitation of water quality criteria, was estimated by optimization-simulation method (OSM) combined with loop approximation calculation. In OSM, water quality is simulated using a water quality model and pollutant load is calculated with a programming model. The effect of changes in pollutant loads on TMAL was discussed. Results showed that the TMAL of nitrogen pollutants in 34 SSRs was 1.49×105 ton/year. The highest TMAL was observed in summer, whereas the lowest in winter. TMAL was also higher in the Bohai Strait and central Bohai Sea and lower in the inner area of the Liaodong Bay, Bohai Bay and Laizhou Bay. In loop approximation calculation, the TMAL obtained was considered satisfactory for water quality criteria as fluctuation of concentration response matrix with pollutant loads was eliminated. Results of numerical experiment further showed that water quality improved faster and were more evident under TMAL input than that when using the EPR method

Air pollution and associated human mortality: The role of air pollutant emissions, climate change and methane concentration increases during the industrial period

Science.gov (United States)

Fang, Y.; Naik, V.; Horowitz, L. W.; Mauzerall, D. L.

2012-12-01

Increases in surface ozone (O3) and fine particulate matter (≤ 2.5μm aerodynamic diameter, PM2.5) are associated with excess premature human mortalities. Here we estimate changes in surface O3 and PM2.5 since preindustrial (1860) times and the global present-day (2000) premature human mortalities associated with these changes. We go beyond previous work to analyze and differentiate the contribution of three factors: changes in emissions of short-lived air pollutants, climate change, and increased methane (CH4) concentrations, to air pollution levels and the associated premature mortalities. We use a coupled chemistry-climate model in conjunction with global population distributions in 2000 to estimate exposure attributable to concentration changes since 1860 from each factor. Attributable mortalities are estimated using health impact functions of long-term relative risk estimates for O3 and PM2.5 from the epidemiology literature. We find global mean surface PM2.5 and health-relevant O3 (defined as the maximum 6-month mean of 1-hour daily maximum O3 in a year) have increased by 8±0.16 μg/m3 and 30±0.16 ppbv, respectively, over this industrial period as a result of combined changes in emissions of air pollutants (EMIS), climate (CLIM) and CH4 concentrations (TCH4). EMIS, CLIM and TCH4 cause global average PM2.5 (O3) to change by +7.5±0.19 μg/m3 (+25±0.30 ppbv), +0.4±0.17 μg/m3 (+0.5±0.28 ppbv), and -0.02±0.01 μg/m3 (+4.3±0.33 ppbv), respectively. Total changes in PM2.5 are associated with 1.5 (95% confidence interval, CI, 1.0-2.5) million all-cause mortalities annually and in O3 are associated with 375 (95% CI, 129-592) thousand respiratory mortalities annually. Most air pollution mortality is driven by changes in emissions of short-lived air pollutants and their precursors (95% and 85% of mortalities from PM2.5 and O3 respectively). However, changing climate and increasing CH4 concentrations also increased premature mortality associated with air

Heavy metal concentrations in forest litter - indicators of pollutant depositions

International Nuclear Information System (INIS)

Angehrn-Bettinazzi, C.; Hertz, J.

1990-01-01

By means of a comparison of the heavy metal concentrations in organic litter from different sites it was examined to what extent the heavy metal concentrations correlate with the atmospheric pollution situation. It follows from the variance analyses: The atmospheric pollution situation is the dominating factor for the heavy metal concentration in L litter. The elements Cd and Zn show a pH-sensitivity at the same time. The lead concentration in the L n and L v horizons reflects the atmospheric pollution situation of the corresponding site. Specific pollution patterns, e.g. in the case of hillside sites, are neither detected through the gravitational deposition (open land) nor through the airborne dust concentration; these can be recognized by the monitor 'litter'. Only horizons in the intercrown area with identical tree vegetation, which are characterized in detail, must be used for monitoring. (orig.) [de

Study of the fumigation effect on pollutants over Inshas area

International Nuclear Information System (INIS)

Tawfik, F.S.; Ramadan, Abou Bakr. A.; Abdel El-Aal, M.M.

2004-01-01

This work aims to investigate the effect of morning fumigation event on the ground level pollutants concentration at inshas area. Monitoring stations for mesuring the hourly continues concetration of some pollutants such sulphur dioxide, carbon monoxide, and ozone were placed near the hot lab in nuclear research center for one complete year, At the same time the hourly averages meteorological parameters were measured continuously at different levels. A fortran computer program was developed to determine the relative relative concentration Assuming accident case in two cases, nonfumigation and morning fumigation. The processing and interpretation of the meteorological data and pollutants concentration revealed that these high pollution events occur almost on daily bassis, usually several hours between sunrise and before afternoon. The maximum fumigation peaks occur earlier in the summer than other seasons owing to theearlier sunrise in addition, ozone concentrations appear to reach their maximum a few hours after intense fumigation events. Maximum hourly concentrations of sulphur dioxide, carbon monoxide and ozone don't exceed threshold values that are considered to be phytotoxic. As sunset pollutant concentration is decrease due to lofting condition

Estimation of maximum credible atmospheric radioactivity concentrations and dose rates from nuclear tests

International Nuclear Information System (INIS)

Telegadas, K.

1979-01-01

A simple technique is presented for estimating maximum credible gross beta air concentrations from nuclear detonations in the atmosphere, based on aircraft sampling of radioactivity following each Chinese nuclear test from 1964 to 1976. The calculated concentration is a function of the total yield and fission yield, initial vertical radioactivity distribution, time after detonation, and rate of horizontal spread of the debris with time. calculated maximum credible concentrations are compared with the highest concentrations measured during aircraft sampling. The technique provides a reasonable estimate of maximum air concentrations from 1 to 10 days after a detonation. An estimate of the whole-body external gamma dose rate corresponding to the maximum credible gross beta concentration is also given. (author)

Development of Indoor Air Pollution Concentration Prediction by Geospatial Analysis

Directory of Open Access Journals (Sweden)

Adyati Pradini Yudison

2015-07-01

Full Text Available People living near busy roads are potentially exposed to traffic-induced air pollutants. The pollutants may intrude into the indoor environment, causing health risks to the occupants. Prediction of pollutant exposure therefore is of great importance for impact assessment and policy making related to environmentally sustainable transport. This study involved the selection of spatial interpolation methods that can be used for prediction of indoor air quality based on outdoor pollutant mapping without indoor measurement data. The research was undertaken in the densely populated area of Karees, Bandung, Indonesia. The air pollutant NO2 was monitored in this area as a preliminary study. Nitrogen dioxide concentrations were measured by passive diffusion tube. Outdoor NO2 concentrations were measured at 94 locations, consisting of 30 roadside and 64 outdoor locations. Residential indoor NO2 concentrations were measured at 64 locations. To obtain a spatially continuous air quality map, the spatial interpolation methods of inverse distance weighting (IDW and Kriging were applied. Selection of interpolation method was done based on the smallest root mean square error (RMSE and standard deviation (SD. The most appropriate interpolation method for outdoor NO2 concentration mapping was Kriging with an SD value of 5.45 µg/m3 and an RMSE value of 5.45 µg/m3, while for indoor NO2 concentration mapping the IDW was best fitted with an RMSE value of 5.92 µg/m3 and an SD value of 5.92 µg/m3.

Concentrations and geographic distribution of selected organic pollutants in Scottish surface soils

International Nuclear Information System (INIS)

Rhind, S.M.; Kyle, C.E.; Kerr, C.; Osprey, M.; Zhang, Z.L.; Duff, E.I.; Lilly, A.; Nolan, A.; Hudson, G.; Towers, W.; Bell, J.; Coull, M.; McKenzie, C.

2013-01-01

Concentrations of selected persistent organic pollutants (POPs) representing three chemical classes (polycyclic aromatic hydrocarbons (PAH), polybrominated diphenyl ethers (PBDE) and polychlorinated biphenyls (PCB) and the organic pollutant diethylhexyl phthalate (DEHP), were determined in surface soil samples (0–5 cm) collected at 20 km grid intersects throughout Scotland over a three-year period. Detectable amounts of all chemical classes and most individual congeners were present in all samples. There were no consistent effects of soil or vegetation type, soil carbon content, pH, altitude or distance from centres of population on concentrations which exhibited extreme variation, even in adjacent samples. It is concluded that soil POPs and DEHP concentrations and associated rates of animal and human exposure were highly variable, influenced by multiple, interacting factors, and not clearly related to local sources but possibly related to wet atmospheric deposition and the organic carbon content of the soil. -- Highlights: •Concentrations of selected organic pollutants in Scottish soils were determined. •Concentrations were highly variable. •There were few effects of soil or vegetation type, soil carbon, pH or altitude. •Distance from cities was not an important determinant of concentrations. •Atmospheric deposition and soil organic carbon content may affect concentrations. -- Soil concentrations of anthropogenic persistent organic pollutants are not clearly related to soil type or pH, vegetation, altitude, or distance from pollutant sources

Maximum permissible concentrations and negligible concentrations for antifouling substances. Irgarol 1051, dichlofluanid, ziram, chlorothalonil and TCMTB

NARCIS (Netherlands)

Wezel AP van; Vlaardingen P van; CSR

2001-01-01

This report presents maximum permissible concentrations and negligible concentrations that have been derived for various antifouling substances used as substitutes for TBT. Included here are Irgarol 1051, dichlofluanide, ziram, chlorothalonil and TCMTB.

Air pollution and associated human mortality: the role of air pollutant emissions, climate change and methane concentration increases from the preindustrial period to present

Directory of Open Access Journals (Sweden)

Y. Fang

2013-02-01

Full Text Available Increases in surface ozone (O₃ and fine particulate matter (≤2.5 μm aerodynamic diameter, PM_2.5 are associated with excess premature human mortalities. We estimate changes in surface O₃ and PM_2.5 from pre-industrial (1860 to present (2000 and the global present-day (2000 premature human mortalities associated with these changes. We extend previous work to differentiate the contribution of changes in three factors: emissions of short-lived air pollutants, climate change, and increased methane (CH₄ concentrations, to air pollution levels and associated premature mortalities. We use a coupled chemistry-climate model in conjunction with global population distributions in 2000 to estimate exposure attributable to concentration changes since 1860 from each factor. Attributable mortalities are estimated using health impact functions of long-term relative risk estimates for O₃ and PM_2.5 from the epidemiology literature. We find global mean surface PM_2.5 and health-relevant O₃ (defined as the maximum 6-month mean of 1-h daily maximum O₃ in a year have increased by 8 ± 0.16 μg m⁻³ and 30 ± 0.16 ppbv (results reported as annual average ±standard deviation of 10-yr model simulations, respectively, over this industrial period as a result of combined changes in emissions of air pollutants (EMIS, climate (CLIM and CH₄ concentrations (TCH4. EMIS, CLIM and TCH₄ cause global population-weighted average PM_2.5 (O₃ to change by +7.5 ± 0.19 μg m⁻³ (+25 ± 0.30 ppbv, +0.4 ± 0.17 μg m⁻³ (+0.5 ± 0.28 ppbv, and 0.04 ± 0.24 μg m⁻³ (+4.3 ± 0.33 ppbv, respectively. Total global changes in PM_2.5 are associated with 1.5 (95% confidence interval, CI, 1.2–1.8 million cardiopulmonary mortalities and 95 (95% CI, 44–144 thousand lung cancer

Influence of ship emission on atmospheric pollutant concentration around Osaka Bay, Japan

International Nuclear Information System (INIS)

Kondo, A.; Yamaguchi, K.; Nishikawa, E.

1999-01-01

Marine traffic in Osaka Bay is very intensified and much atmosphere pollutant (SO x and NO x ) from ships is released but there is no regulation about the ship emission. In this paper, we investigated the emission amounts of SO x NO x and HC from car, factory and ships in Osaka bay area and estimated the influence of the ship emission on the atmospheric pollutant concentration, using both the meteorological prediction model and the atmospheric pollutant concentration prediction model including the dry deposition and the chemical reaction. In Osaka bay area, the emission amounts of SO x and NO x from ships were about 30% of the total emission amounts, respectively. Using these emission data, the atmospheric pollutant concentration was simulated on a summer fine day when high oxidant concentration was measured at several observatories and was compared with the observed data. Though some differences were seen between the simulated results and the observed data, the diurnal variation agreed reasonably. The second simulation was carried out except for the ship emission and we estimated the influence of the ship emission on the atmospheric pollutant concentration. It was found that the ship emission raised SO 2 , NO 2 and NO concentration not only in shore area but also in 40km inland. (Author)

Study on Relationship between Seasonal Temperatures and Municipal Wastewater Pollutant Concentration and Removal Rate

Directory of Open Access Journals (Sweden)

Yuan Shaoxiong

2016-01-01

Full Text Available In this study, the temperatures, pollutant concentrations and other indicators of municipal wastewater influent and effluent were tested for 7 months in 6 constructed wetland microcosms; the hydraulic retention time is 2 days. The results indicated that for both influent and effluent, there was a highly significant negative correlation (P<0.01 between the temperature and the pollutant concentrations, there was a significant difference (P<0.05 between seasonal temperatures, and the pollutant concentrations in summer and autumn were significantly different from those in winter (P<0.05. Furthermore, a regression analysis of pollutant concentration (y based on changes in water temperature (x in different seasons was performed. The analysis revealed that the relationship has the form ‘y = a -bx + cx2’, that under certain circumstances, pollutant concentrations can be calculated based on the temperature, and that the concentrations of NH4-N, Total Phosphorus (TP and Soluble Reactive Phosphorus (SRP had a significantly negative correlation with their removal rate (P < 0.01. However, seasonal temperature clearly did not have a direct impact on the pollutant concentration, and some studies have indicated that the different manners in which urban residents use water as the temperature changes may be the real reason that the pollutant concentrations of municipal wastewater vary with seasonal temperature. Furthermore, when designing and operating constructed wetlands, the impact of the changes in pollutant concentrations generated by seasonal temperature should be fully considered, dilution and other means should be taken to ensure purification.

Concentration reduction of selected pollutants in fish culture ...

African Journals Online (AJOL)

Concentration reduction of selected pollutants in fish culture effluents using plastic straws and palm kernel shells. ... Journal of Environmental Extension ... Their effluent treatment ability were evaluated in terms of reduction made to ...

Relations between Scots pine needle element concentrations and decreased needle longevity along pollution gradients

International Nuclear Information System (INIS)

Lamppu, Jukka; Huttunen, Satu

2003-01-01

Deceased needle longevity was related to increased heavy metal concentrations. - Scots pine (Pinus sylvestris L.) shoots were sampled along transects near one urban pollution source and two smelters. Needle Mg, P and K concentrations decreased from the second to the fourth age class linearly with needle survival along the urban pollution gradient. Still, over 80% of the average concentration of these nutrients remained in the fourth needle age class. Decreased needle longevity was closely related to the increased heavy metal concentrations near the smelters. Near the urban pollution source, it was related to the increased annual needle mass and the increased needle nutrient concentrations. Decreased Mn accumulation along with needle age was detected near all pollution sources. Leaching of Mn from needles and especially from soil as a cause of decreased needle concentrations is discussed

Ozone pollution and ozone biomonitoring in European cities. Part I: Ozone concentrations and cumulative exposure indices at urban and suburban sites

DEFF Research Database (Denmark)

Klumpp, A.; Ansel, W.; Klumpp, G.

2006-01-01

In the frame of a European research project on air quality in urban agglomerations, data on ozone concentrations from 23 automated urban and suburban monitoring stations in 11 cities from seven countries were analysed and evaluated. Daily and summer mean and maximum concentrations were computed...... based on hourly mean values, and cumulative ozone exposure indices (Accumulated exposure Over a Threshold of 40 ppb (AOT40), AOT20) were calculated. The diurnal profiles showed a characteristic pattern in most city centres, with minimum values in the early morning hours, a strong rise during the morning......, by contrast, maximum values were lower and diurnal variation was much smaller. Based on ozone concentrations as well as on cumulative exposure indices, a clear north-south gradient in ozone pollution, with increasing levels from northern and northwestern sites to central and southern European sites...

Prediction on long-term mean and mean square pollutant concentrations in an urban atmosphere

Energy Technology Data Exchange (ETDEWEB)

Kumar, S; Lamb, R G; Seinfeld, J H

1976-01-01

The general problem of predicting long-term average (say yearly) pollutant concentrations in an urban atmosphere is formulated. The pollutant concentration can be viewed as a random process, the complete description of which requires knowledge of its probability density function, which is unknown. The mean concentration is the first moment of the concentration distribution, and at present there exist a number of models for predicting the long-term mean concentration of an inert pollutant. The second moment, or mean square concentration, indicates additional features of the distribution, such as the level of fluctuations about the mean. In the paper a model proposed by Lamb for the long-term mean concentration is reviewed, and a new model for prediction of the long-term mean square concentration of an inert air pollutant is derived. The properties and uses of the model are discussed, and the equations defining the model are presented in a form for direct application to an urban area.

Predicting long-term average concentrations of traffic-related air pollutants using GIS-based information

Science.gov (United States)

Hochadel, Matthias; Heinrich, Joachim; Gehring, Ulrike; Morgenstern, Verena; Kuhlbusch, Thomas; Link, Elke; Wichmann, H.-Erich; Krämer, Ursula

Global regression models were developed to estimate individual levels of long-term exposure to traffic-related air pollutants. The models are based on data of a one-year measurement programme including geographic data on traffic and population densities. This investigation is part of a cohort study on the impact of traffic-related air pollution on respiratory health, conducted at the westerly end of the Ruhr-area in North-Rhine Westphalia, Germany. Concentrations of NO 2, fine particle mass (PM 2.5) and filter absorbance of PM 2.5 as a marker for soot were measured at 40 sites spread throughout the study region. Fourteen-day samples were taken between March 2002 and March 2003 for each season and site. Annual average concentrations for the sites were determined after adjustment for temporal variation. Information on traffic counts in major roads, building densities and community population figures were collected in a geographical information system (GIS). This information was used to calculate different potential traffic-based predictors: (a) daily traffic flow and maximum traffic intensity of buffers with radii from 50 to 10 000 m and (b) distances to main roads and highways. NO 2 concentration and PM 2.5 absorbance were strongly correlated with the traffic-based variables. Linear regression prediction models, which involved predictors with radii of 50 to 1000 m, were developed for the Wesel region where most of the cohort members lived. They reached a model fit ( R2) of 0.81 and 0.65 for NO 2 and PM 2.5 absorbance, respectively. Regression models for the whole area required larger spatial scales and reached R2=0.90 and 0.82. Comparison of predicted values with NO 2 measurements at independent public monitoring stations showed a satisfactory association ( r=0.66). PM 2.5 concentration, however, was only slightly correlated and thus poorly predictable by traffic-based variables ( rGIS-based regression models offer a promising approach to assess individual levels of

Pollutant concentrations in road runoff: Southeast Queensland case study

Energy Technology Data Exchange (ETDEWEB)

Drapper, D.; Tomlinson, R.; Williams, P.

2000-04-01

This paper discusses the results of research into the pollutants in runoff from road pavement surfaces following natural rainfall events. Road runoff water quality was monitored at 21 sites centering around Brisbane, in southeast Queensland, Australia. The sites were selected according to traffic volumes, surrounding land use, pavement surface type, ease of access, and commercial vehicle percentage. Bridge sites were chosen for convenience of sample collection and minimized infrastructure modification. First flush grab samplers were permanently installed at each site to collect the first 20 L of runoff from one of the bridge drainage scuppers. The runoff samples were tested for a number of heavy metals, hydrocarbons, pesticides, and other physical characteristics. The observed results fall within the ranges of concentrations reported internationally and nationally but do not typically follow the 30,000 average annual daily traffic results reported in the United States. Traffic volumes have not been found to be the best indicator of road runoff pollutant concentrations. Interevent duration has been found to be a statistically significant factor for pollutant concentrations. Sites incorporating exit lanes have recorded higher concentrations of acid-extractable copper and zinc, tending to support the hypothesis that brake pad and tire wear caused by rapid deceleration contributes to the concentrations of these metals in road runoff. Laser particle sizing has shown that a significant proportion of the sediment found in the runoff is <100 {micro}m. However, these particulates do settle in water within 24 h, under laboratory conditions. This may be due to the presence of heavy metals.

Impacts of Mercury Pollution Controls on Atmospheric Mercury Concentration and Occupational Mercury Exposure in a Hospital.

Science.gov (United States)

Li, Ping; Yang, Yan; Xiong, Wuyan

2015-12-01

Mercury (Hg) and Hg-containing products are used in a wide range of settings in hospitals. Hg pollution control measures were carried out in the pediatric ward of a hospital to decrease the possibility of Hg pollution occurring and to decrease occupational Hg exposure. Total gaseous Hg (TGM) concentrations in the pediatric ward and hair and urine Hg concentrations for the pediatric staff were determined before and after the Hg pollution control measures had been implemented. A questionnaire survey performed indicated that the pediatric staff had little understanding of Hg pollution and that appropriate disposal techniques were not always used after Hg leakage. TGM concentrations in the pediatric ward and urine Hg (UHg) concentrations for the pediatric staff were 25.7 and 22.2% lower, respectively, after the Hg pollution control measures had been implemented than before, which indicated that the control measures were effective. However, TGM concentrations in the pediatric ward remained significantly higher than background concentrations and UHg concentrations for the pediatric staff were remained significantly higher than the concentrations in control group, indicating continued existence of certain Hg pollution.

The relationships between air pollutants, meteorological parameters and concentration of airborne fungal spores

International Nuclear Information System (INIS)

Grinn-Gofron, Agnieszka; Strzelczak, Agnieszka; Wolski, Tomasz

2011-01-01

Fungal spores are an important component of bioaerosol and also considered to act as indicator of the level of atmospheric bio-pollution. Therefore, better understanding of these phenomena demands a detailed survey of airborne particles. The objective of this study was to examine the dependence of two the most important allergenic taxa of airborne fungi - Alternaria and Cladosporium - on meteorological parameters and air pollutant concentrations during three consecutive years (2006-2008). This study is also an attempt to create artificial neural network (ANN) forecasting models useful in the prediction of aeroallergen abundance. There were statistically significant relationships between spore concentration and environmental parameters as well as pollutants, confirmed by the Spearman's correlation rank analysis and high performance of the ANN models obtained. The concentrations of Cladosporium and Alternaria spores can be predicted with quite good accuracy from meteorological conditions and air pollution recorded three days earlier. - ANN models predict airspore contents from weather conditions and air pollutant.

Meteorological detrending of primary and secondary pollutant concentrations: Method application and evaluation using long-term (2000-2012) data in Atlanta

Science.gov (United States)

Henneman, Lucas R. F.; Holmes, Heather A.; Mulholland, James A.; Russell, Armistead G.

2015-10-01

The effectiveness of air pollution regulations and controls are evaluated based on measured air pollutant concentrations. Air pollution levels, however, are highly sensitive to both emissions and meteorological fluctuations. Therefore, an assessment of the change in air pollutant levels due to emissions controls must account for these meteorological fluctuations. Two empirical methods to quantify the impact of meteorology on pollutant levels are discussed and applied to the 13-year time period between 2000 and 2012 in Atlanta, GA. The methods employ Kolmogorov-Zurbenko filters and linear regressions to detrended pollutant signals into long-term, seasonal, weekly, short-term, and white-noise components. The methods differ in how changes in weekly and holiday emissions are accounted for. Both can provide meteorological adjustments on a daily basis for future use in acute health analyses. The meteorological impact on daily signals of ozone, NOx, CO, SO2, PM2.5, and PM species are quantified. Analyses show that the substantial decreases in seasonal averages of NOx and SO2 correspond with controls implemented in the metropolitan Atlanta area. Detrending allows for the impacts of some controls to be observed with averaging times of as little as 3 months. Annual average concentrations of NOx, SO2, and CO have all fallen by at least 50% since 2000. Reductions in NOx levels, however, do not lead to uniform reductions in ozone. While average detrended summer average maximum daily average 8 h ozone (MDA8h O3) levels fell by 4% (2.2 ± 2 ppb) between 2000 and 2012, winter averages have increased by 12% (3.8 ± 1.4 ppb), providing further evidence that high ozone levels are NOx-limited and lower ozone concentrations are NOx-inhibited. High ozone days (with MDA8h O3 greater than 60 ppb) decreased both in number and in magnitude over the study period.

Estimation of air quality by air pollution indices

International Nuclear Information System (INIS)

Liblik, Valdo; Kundel, Helmut

1999-01-01

A novel system for estimating the quality of atmospheric air in the over-ground air layer with the help of air pollution indices was developed. The method is based on a comparison of measured or calculated maximum short-term concentrations and average annual concentrations of pollutants with maximum permissible concentrations (with regard to human beings and vegetation). Special air quality estimation scales for residential areas and natural systems are presented. On the basis of the concentration of the substance under study zones of very high, high, rather high, moderate, low and very low air pollution were distinguished in the over-ground layer of the atmosphere. These are projected to land surface for landscape zonation. The application of the system of indices is demonstrated in the analysis of air quality for the towns of Kohtla-Jarve, Johvi and Kivioli (in 1997-1998). A comparative analysis of the air pollution zones distinguished on the basis of emissions and data from bio monitoring yielded satisfactory results. The system of air pollution indices developed enables to process the results of air monitoring in case of pollution fields of complicated composition so that the result for estimating the quality of ambient air in a residential area is easily understood by inhabitants and interpretable with the help of a special scale; analyse temporal changes in the quality of the air in towns, villages and other residential areas and use the results as basis for developing measures for reducing the pollution of ambient air; carry out zonation of large territories on the basis of air pollution levels (spatial air pollution zones are projected on the ground surface) and estimate air quality in places where air monitoring is lacking to forecast the possible effect of air pollution on natural systems (author)

Aerodynamic effects of trees on pollutant concentration in street canyons.

Science.gov (United States)

Buccolieri, Riccardo; Gromke, Christof; Di Sabatino, Silvana; Ruck, Bodo

2009-09-15

This paper deals with aerodynamic effects of avenue-like tree planting on flow and traffic-originated pollutant dispersion in urban street canyons by means of wind tunnel experiments and numerical simulations. Several parameters affecting pedestrian level concentration are investigated, namely plant morphology, positioning and arrangement. We extend our previous work in this novel aspect of research to new configurations which comprise tree planting of different crown porosity and stand density, planted in two rows within a canyon of street width to building height ratio W/H=2 with perpendicular approaching wind. Sulfur hexafluoride was used as tracer gas to model the traffic emissions. Complementary to wind tunnel experiments, 3D numerical simulations were performed with the Computational Fluid Dynamics (CFD) code FLUENT using a Reynolds Stress turbulence closure for flow and the advection-diffusion method for concentration calculations. In the presence of trees, both measurements and simulations showed considerable larger pollutant concentrations near the leeward wall and slightly lower concentrations near the windward wall in comparison with the tree-less case. Tree stand density and crown porosity were found to be of minor importance in affecting pollutant concentration. On the other hand, the analysis indicated that W/H is a more crucial parameter. The larger the value of W/H the smaller is the effect of trees on pedestrian level concentration regardless of tree morphology and arrangement. A preliminary analysis of approaching flow velocities showed that at low wind speed the effect of trees on concentrations is worst than at higher speed. The investigations carried out in this work allowed us to set up an appropriate CFD modelling methodology for the study of the aerodynamic effects of tree planting in street canyons. The results obtained can be used by city planners for the design of tree planting in the urban environment with regard to air quality issues.

Contribution of ship emissions to the concentration and deposition of air pollutants in Europe

Directory of Open Access Journals (Sweden)

S. Aksoyoglu

2016-02-01

Full Text Available Emissions from the marine transport sector are one of the least-regulated anthropogenic emission sources and contribute significantly to air pollution. Although strict limits were introduced recently for the maximum sulfur content in marine fuels in the SECAs (sulfur emission control areas and in EU ports, sulfur emissions outside the SECAs and emissions of other components in all European maritime areas have continued to increase in the last two decades. We have used the air quality model CAMx (Comprehensive Air Quality Model with Extensions with and without ship emissions for the year 2006 to determine the effects of international shipping on the annual as well as seasonal concentrations of ozone, primary and secondary components of PM2.5, and the dry and wet deposition of nitrogen and sulfur compounds in Europe. The largest changes in pollutant concentrations due to ship emissions were predicted for summer. Concentrations of particulate sulfate increased due to ship emissions in the Mediterranean (up to 60 %, the English Channel and the North Sea (30–35 %, while increases in particulate nitrate levels were found especially in the north, around the Benelux area (20 %, where there were high NH3 land-based emissions. Our model results showed that not only are the atmospheric concentrations of pollutants affected by ship emissions, but also depositions of nitrogen and sulfur compounds increase significantly along the shipping routes. NOx emissions from the ships, especially in the English Channel and the North Sea, cause a decrease in the dry deposition of reduced nitrogen at source regions by moving it from the gas phase to the particle phase which then contributes to an increase in the wet deposition at coastal areas with higher precipitation. In the western Mediterranean region, on the other hand, model results show an increase in the deposition of oxidized nitrogen (mostly HNO3 due to the ship traffic. Dry deposition of SO2 seems to

Double-tailored nonimaging reflector optics for maximum-performance solar concentration.

Science.gov (United States)

Goldstein, Alex; Gordon, Jeffrey M

2010-09-01

A nonimaging strategy that tailors two mirror contours for concentration near the étendue limit is explored, prompted by solar applications where a sizable gap between the optic and absorber is required. Subtle limitations of this simultaneous multiple surface method approach are derived, rooted in the manner in which phase space boundaries can be tailored according to the edge-ray principle. The fundamental categories of double-tailored reflective optics are identified, only a minority of which can pragmatically offer maximum concentration at high collection efficiency. Illustrative examples confirm that acceptance half-angles as large as 30 mrad can be realized at a flux concentration of approximately 1000.

Anew applied approach for dynamic air quality simulation in industrial and nuclear polluted areas

International Nuclear Information System (INIS)

Abdel Aal, M.M.; Tawfik, F.S.; Ramadan, A.

2002-01-01

Air pollution transport and diffusion and diffusion models are the only tools for inferring a quantitative deterministic relation between pollutant emissions and ambient air quality. This study deals with the simulation of pollutants transport and diffusion at shobra El-Khemia, where this site is considered the most public and polluted area in greater cairo city. The results of such a model matches to a great extent with the measured ones because it takes into consideration dry and wet deposition and first-order reaction chemistry. Specified time period was chosen to simulate the pollutant of sulphur dioxide over the studied area. The meteorological parameters were measured to calculate the hourly stability classes and height of mixing layer. Also, the concentration of sulphur dioxide was continuously measured at the faculty of agriculture to compare between its values and the estimated results. Yen's factory was taken to be the source of pollutant, thus, the emission rate and concentration of sulphur dioxide were measured at the top of their stacks. The analysis of estimated results provided that, at neutral condition, there was only one maximum concentration while at unstable conditions, there were more than one maximum concentration. The maximum estimated average hourly concentration and the average daily measuring concentration at shoubra Elkheima were within the air quality limit of egyptian law no. 4 (1994). The measured values are greater than the estimated ones by 15 to 30 % . This could be attributed to the effect of transportation, which was neglected during the application of model

Pollutant Concentrations in the Rime and Fog Water

Czech Academy of Sciences Publication Activity Database

Fišák, Jaroslav; Tesař, Miroslav; Fottová, D.

2008-01-01

Roč. 3, č. 1 (2008), S68-S73 ISSN 1801-5395 R&D Projects: GA AV ČR IAA3042301; GA AV ČR 1QS200420562 Institutional research plan: CEZ:AV0Z30420517; CEZ:AV0Z20600510 Keywords : fog water * rime water * pollutant concentration Subject RIV: DG - Athmosphere Sciences, Meteorology

Measuring concentrations of selected air pollutants inside California vehicles. Final report

International Nuclear Information System (INIS)

Rodes, C.; Sheldon, L.; Whitaker, D.; Clayton, A.; Fitzgerald, K.

1999-01-01

This project measured 2-hour integrated concentrations of PM10, PM2.5, metals and a number of organic chemicals including benzene and MTBE inside vehicles on California roadways. Using continuous samplers, particle counts, black carbon, and CO were also measured. In addition to measuring in-vehicle levels, the investigators measured pollutant levels just outside the vehicle, at roadside stations, and ambient air monitoring stations. Different driving scenarios were designed to assess the effects of a number of factors on in-vehicle pollutant levels. These factors included roadway type, carpool lanes, traffic conditions, geographical locations, vehicle type, and vehicle ventilation conditions. The statewide average in-vehicle concentrations of benzene, MTBE, and formaldehyde ranged from 3--22 microg/m 3 , 3--90 microg/m 3 , and 0---22 microg/m 3 , respectively. The ranges of mean PM10 and PM2.5 in-vehicle levels in Sacramento were 20--40 microg/m 3 and 6--22 microg/m 3 , respectively. In general, pollutant levels inside or just outside the vehicles were higher than those measured at the roadside stations or the ambient air stations. In-vehicle pollutant levels were consistently higher in Los Angeles than Sacramento. Pollutant levels measured inside vehicles traveling in a carpool lane were much lower than those in the right-hand, slower lanes. Under the study conditions, factors such as vehicle type and ventilation and little effect on in-vehicle pollutant levels. Other factors, such as roadway type, freeway congestion level, and time-of-day had some influence on in-vehicle pollution levels

Determine the Efficacy of Salinity on Bioremediation of Polluted Soil by Phenanthrene

Directory of Open Access Journals (Sweden)

Masoumeh Ravanipour

2011-04-01

Full Text Available Background: Phenanthrene is one of the Polycyclic Aromatic Hydrocarbons (PAHs that are formed during the incomplete combustion of fossil fuels, oil pollution and different process of oil and gas plants. PAHs-contaminated area have increased a health risk to humans and environments due to toxicity, carcinogenicity, hydrophobicity and their tendency to accumulation in soil and sediment and their entrance to food chain. Bioremediation is an effective method for removing toxic pollutants from soils such as Phenanthrene. The main object of this study is the assessment of the effects of salinity on the efficacy of the process of bioremediation on polluted soils by Phenanthrene. Methods: The bare soil of any organic and microbial pollution was first polluted artificially to the phenanthrene then a nutrient solution with two minimum and maximum concentrations of salinity were added to it in order to have the proportion of 10% w:v (soil: water. After that a microbial mixture which was enable degradation the phenanthrene added to the slurry and aerated. After the extraction of phenanthrene by ultrasonic, the residual concentration in the soil was analyzed by GC. Results: In the conditions that salinity concentration was maximum, the microbial growth has a longer lag phase than the minimum salinity. The findings from extraction process by GC depict the removal percentage of maximum and minimum salinity in 56th %70.5 day and %71.8, respectively. Conclusion: In In spite of the longer log phase of maximum concentration of salinity and according to GC results, there was just a little difference between two solutions. Therefore it reveals that salinity can increase the lag phase but haven't any inhibitory effect on Phenanthrene removal.

Can We Manage Nonpoint-Source Pollution Using Nutrient Concentrations during Seasonal Baseflow?

Directory of Open Access Journals (Sweden)

James A. McCarty

2016-05-01

Full Text Available Nationwide, a substantial amount of resources has been targeted toward improving water quality, particularly focused on nonpoint-source pollution. This study was conducted to evaluate the relationship between nutrient concentrations observed during baseflow and runoff conditions from 56 sites across five watersheds in Arkansas. Baseflow and stormflow concentrations for each site were summarized using geometric mean and then evaluated for directional association. A significant, positive correlation was found for NO–N, total N, soluble reactive P, and total P, indicating that sites with high baseflow concentrations also had elevated runoff concentrations. Those landscape factors that influence nutrient concentrations in streams also likely result in increased runoff, suggesting that high baseflow concentrations may reflect elevated loads from the watershed. The results highlight that it may be possible to collect water-quality data during baseflow to help define where to target nonpoint-source pollution best management practices within a watershed.

mathematical modelling of atmospheric dispersion of pollutants

International Nuclear Information System (INIS)

Mohamed, M.E.

2002-01-01

the main objectives of this thesis are dealing with environmental problems adopting mathematical techniques. in this respect, atmospheric dispersion processes have been investigated by improving the analytical models to realize the realistic physical phenomena. to achieve these aims, the skeleton of this work contained both mathematical and environmental topics,performed in six chapters. in chapter one we presented a comprehensive review study of most important informations related to our work such as thermal stability , plume rise, inversion, advection , dispersion of pollutants, gaussian plume models dealing with both radioactive and industrial contaminants. chapter two deals with estimating the decay distance as well as the decay time of either industrial or radioactive airborne pollutant. further, highly turbulent atmosphere has been investigated as a special case in the three main thermal stability classes namely, neutral, stable, and unstable atmosphere. chapter three is concerned with obtaining maximum ground level concentration of air pollutant. the variable effective height of pollutants has been considered throughout the mathematical treatment. as a special case the constancy of effective height has been derived mathematically and the maximum ground level concentration as well as its location have been established

Prediction of Air Pollutants Concentration Based on an Extreme Learning Machine: The Case of Hong Kong

OpenAIRE

Zhang, Jiangshe; Ding, Weifu

2017-01-01

With the development of the economy and society all over the world, most metropolitan cities are experiencing elevated concentrations of ground-level air pollutants. It is urgent to predict and evaluate the concentration of air pollutants for some local environmental or health agencies. Feed-forward artificial neural networks have been widely used in the prediction of air pollutants concentration. However, there are some drawbacks, such as the low convergence rate and the local minimum. The e...

Loading Concentrations of Pollutant in Alur Ilmu at UKM Bangi Campus: Event Mean Concentration (EMC) Approach

International Nuclear Information System (INIS)

Haslinur Md Din; Mohd Ekhwan Toriman; Mazlin Mokhtar

2012-01-01

Water pollutant loadings and river discharge are among the basic data used in determining the dynamicity of a river. The input of water quality and river discharge are usually available through the collection of water samples in the field or at the observatory, and are done automatically using the data logger sensor. This paper discusses the concentrations pollutant load water quality and its relationship with discharge (m 3 / s) using Event Mean Concentration (EMC) in the Alur Ilmu, UKM source from the Diptrokarp forest at Hutan Simpan Bangi (2 degree 55' 1 4.72 N 101 degree 46' 5 7.37 E). Alur Ilmu is a 1.79 km long stretching across the main campus of National University of Malaysia before flowing into the Langat River. Water quality was measured using automatic gauging and continuous water quality stations which are installed at downstream of Alur Ilmu (2 degree 55 ' 40.33 N 100 degree 46 ' 47.15 E) and involves in measuring the parameters of total dissolved solid (TDS) and dissolved oxygen (DO). Laboratory analysis carried out for chemical parameters such as ammonia nitrogen (NH 3 -N), total suspended solid (TSS), biochemical oxygen demand (BOD) and chemical oxygen demand (COD) in accordance with guidelines American Public Health Association (APHA, 1995). The normal discharge rate recorded at Alur Ilmu is 0.33 m 3 / s and the wet discharge is 13.04 m 3 / s.The total estimated pollutant loadings according to EMC as DO (18.51±3.01 mg/ L), TDS (794.92±186.72 mg/ L), BOD (11.57±0.28 mg/ L), COD (201.29±1.55 mg/ l), TSS (470.03±27.63 mg/ L) and Ammonia Nitrogen (2.52±0.0 mg/ L). Correlation test showed a direct relationship between rainfall and flow (Q) and several pollutant loadings with R 2 =1 at a significance level of 0.05. The study also classified some of the pollutants concentrations in class III and IV as determined by the Water Quality Index (WQI). (author)

A study on air pollution concentration at Desa parkcity construction site

African Journals Online (AJOL)

This study assesses the effect of construction workers exposure towards the air pollution to the correlation between meteorological factor with the particulate matter and other gases concentration at a construction site in DesaParkcity. The concentration of PM was collected by using low volume sampler meanwhile CO, CO2, ...

Sources and levels of concentration of metal pollutants in Kubanni dam, Zaria, Nigeria

Directory of Open Access Journals (Sweden)

Butu, A.W.

2013-06-01

Full Text Available The paper looked at the sources and levels of concentration of metal pollutants in Kubanni dam, Zaria, Nigeria. The main sources of data for the study were sediment from four different sections of the long profile of the dam. The samples were prepared in the laboratory according to standard methods and the instrumental Neutron Activation Analysis (INAA technique was adopted in the analysis using Nigeria Research Reactor – 1 (NIRR – 1. The results of the analysis showed that 29 metal pollutants; Mg, Al, Ca, Ti, V, Mn, Dy, Na, K, As, La, Sm, Yb, U, Br, Sc, Cr, Fe, Co, Rb, Zn,Cs, Ba, Eu, Lu, Hf, Ta, Sb and Th currently exist in Kubanni dam in various levels of concentrations. The results showed that most of the metal pollutants in the dam are routed to anthropogenic activities within the dam catchment area while few are routed to geologic formation. The results further revealed that metal pollutants that their sources are traceable to refuse dumps, farmlands, public drains and effluents showed higher levels of concentration in the dam than the ones that are gradually released from the soil regolith system.

Influence of water pollution on the growth and pigment concentration of the microalgae Phaeodactylum tricornutum Bohlin (Bacillariophyta).

Science.gov (United States)

Zhuravel, Elena V; Markina, Zhanna V; Aizdaicher, Nina A

2012-05-01

The aim of the work was to study the influence of the water taken from one of the most polluted parts of the Peter the Great Bay (the Japan Sea), the Nakhodka Bay, on the growth and chlorophyll a concentration in the cells of microalga P. tricornutum Bohlin (Bacillariophyta). The estimation of the dynamics of cell number growth and chlorophyll a concentration in the cells of microalga grown in the water from the Nakhodka Bay was made. At the same time, in 2007-2008, the main hydrochemical parameters, such as water salinity, dissolved oxygen concentration, BOD(5), organic and mineral phosphates concentration, anionic surfactants, and total petroleum hydrocarbons, were determined. It is shown that in July 2007, when most hydrochemical parameters were lower than the maximum permissible level, the culture growth and chlorophyll a contents in the cells did not differ from the control for certain. In other seasons these indices differed greatly from the control. The positive correlation between the concentration of dissolved oxygen, phosphates, petroleum hydrocarbons, and the number of microalga cells, grown in the water from the Nakhodka Bay, was shown.

Effect of aquatic plants on 95Zr concentration in slightly polluted water

International Nuclear Information System (INIS)

Shi Jianjun; Yang Ziyin; Chen Hui

2004-01-01

Effect of three aquatic plants (Ceratophyllum demersum, Azolla caroliniana and Eichhornia crassipes) on 95 Zr concentration in slightly polluted water was studied by using isotope tracer techniques. The results showed that the aquatic plants had strong ability of 95 Zr concentration in water. The concentration factor (CF) were from 56.78 to 112.94, so three aquatic plants were suggested be bio-indicators for 95 Zr polluted water. The specific activity of 95 Zr in water decreased with time when the aquatic plants were put in slightly 95 Zr polluted water. The descent of specific activity of 95 Zr in water was very quick during the beginning period (0-3d). The time for the specific activity reduced to 50% was only 3 days, indicating that theres aquatic plants could be used to purge slightly 95 Zr polluted water. The effect of Eichhornia crassipes on purging 95 Zr in water was the best among the three aquatic plants. The specific activity of 95 Zr in bottom clay only decreased 5% after putting aquatic plants in water, indicating that desorption of 95 Zr from bottom clay was not easy. As the bottom clay had strong ability of adsorption and fixation to 95 Zr, the effect of aquatic plant on purging 95 Zr adsorbed by bottom clay was not visible

The electric power stations viewed as a source of local and transfrontier pollution

International Nuclear Information System (INIS)

Motiu, C.; Sandu, I.

1994-01-01

The pollutant emission of the thermal power stations may have an important contribution to the local pollution as well as to regional (transfrontier) and global pollution. Due to the impossibility at present of making continuous monitoring of the emission of pollutants it is necessary to use computational models for obtaining inventories of the pollutant sources and for studying their dispersion into atmosphere. The computational code used to simulate the pollutant diffusion in the atmosphere is a climatologic model giving the annual average concentration and the evaluation of the maximum SO 2 concentration. The paper presents the analyses for the case of 14 thermal power stations of Romania

Aerodynamic effects of trees on pollutant concentration in street canyons

NARCIS (Netherlands)

Buccolieri, R.; Gromke, C.B.; Sabatino, Di S.; Ruck, B.

2009-01-01

This paper deals with aerodynamic effects of avenue-like tree planting on flow and traffic-originated pollutant dispersion in urban street canyons by means of wind tunnel experiments and numerical simulations. Several parameters affecting pedestrian level concentration are investigated, namely plant

Long short-term memory neural network for air pollutant concentration predictions: Method development and evaluation

International Nuclear Information System (INIS)

Li, Xiang; Peng, Ling; Yao, Xiaojing; Cui, Shaolong; Hu, Yuan; You, Chengzeng; Chi, Tianhe

2017-01-01

Air pollutant concentration forecasting is an effective method of protecting public health by providing an early warning against harmful air pollutants. However, existing methods of air pollutant concentration prediction fail to effectively model long-term dependencies, and most neglect spatial correlations. In this paper, a novel long short-term memory neural network extended (LSTME) model that inherently considers spatiotemporal correlations is proposed for air pollutant concentration prediction. Long short-term memory (LSTM) layers were used to automatically extract inherent useful features from historical air pollutant data, and auxiliary data, including meteorological data and time stamp data, were merged into the proposed model to enhance the performance. Hourly PM 2.5 (particulate matter with an aerodynamic diameter less than or equal to 2.5 μm) concentration data collected at 12 air quality monitoring stations in Beijing City from Jan/01/2014 to May/28/2016 were used to validate the effectiveness of the proposed LSTME model. Experiments were performed using the spatiotemporal deep learning (STDL) model, the time delay neural network (TDNN) model, the autoregressive moving average (ARMA) model, the support vector regression (SVR) model, and the traditional LSTM NN model, and a comparison of the results demonstrated that the LSTME model is superior to the other statistics-based models. Additionally, the use of auxiliary data improved model performance. For the one-hour prediction tasks, the proposed model performed well and exhibited a mean absolute percentage error (MAPE) of 11.93%. In addition, we conducted multiscale predictions over different time spans and achieved satisfactory performance, even for 13–24 h prediction tasks (MAPE = 31.47%). - Highlights: • Regional air pollutant concentration shows an obvious spatiotemporal correlation. • Our prediction model presents superior performance. • Climate data and metadata can significantly

Heavy metal concentrations in a soil-plant-snail food chain along a terrestrial soil pollution gradient.

NARCIS (Netherlands)

Notten, M.J.M.; Oosthoek, A.; Rozema, J.; Aerts, R.

2005-01-01

We investigated concentrations of Zn, Cu, Cd and Pb in the compartments of a soil-plant (Urtica dioica)-snail (Cepaea nemoralis) food chain in four polluted locations in the Biesbosch floodplains, the Netherlands, and two reference locations. Total soil metal concentrations in the polluted locations

Ambient concentrations of aldehydes in relation to Beijing Olympic air pollution control measures

Science.gov (United States)

Gong, J. C.; Zhu, T.; Hu, M.; Zhang, L. W.; Cheng, H.; Zhang, L.; Tong, J.; Zhang, J.

2010-08-01

Aldehydes are ubiquitous constituents of the atmosphere. Their concentrations are elevated in polluted urban atmospheres. The present study was carried out to characterize three aldehydes of most health concern (formaldehyde, acetaldehyde, and acrolein) in a central Beijing site in the summer and early fall of 2008 (from June to October). Measurements were made before, during, and after the Beijing Olympics to examine whether the air pollution control measures implemented to improve Beijing's air quality during the Olympics had any impact on concentrations of the three aldehydes. Average concentrations of formaldehyde, acetaldehyde and acrolein were 29.34 ± 15.12 μg/m3, 27.09 ± 15.74 μg/m3 and 2.32 ± 0.95 μg/m3, respectively, for the entire period of measurements, all being the highest among the levels measured in cities around the world in photochemical smog seasons. Among the three measured aldehydes, only acetaldehyde had a substantially reduced mean concentration during the Olympic air pollution control period compared to the pre-Olympic period. Formaldehyde and acrolein followed the changing pattern of temperature and were each significantly correlated with ozone (a secondary product of photochemical reactions). In contrast, acetaldehyde was significantly correlated with several pollutants emitted mainly from local emission sources (e.g., NO2, CO, and PM2.5). These findings suggest that local direct emissions had a larger impact on acetaldehyde than formaldehyde and acrolein.

A new air quality monitoring and early warning system: Air quality assessment and air pollutant concentration prediction.

Science.gov (United States)

Yang, Zhongshan; Wang, Jian

2017-10-01

Air pollution in many countries is worsening with industrialization and urbanization, resulting in climate change and affecting people's health, thus, making the work of policymakers more difficult. It is therefore both urgent and necessary to establish amore scientific air quality monitoring and early warning system to evaluate the degree of air pollution objectively, and predict pollutant concentrations accurately. However, the integration of air quality assessment and air pollutant concentration prediction to establish an air quality system is not common. In this paper, we propose a new air quality monitoring and early warning system, including an assessment module and forecasting module. In the air quality assessment module, fuzzy comprehensive evaluation is used to determine the main pollutants and evaluate the degree of air pollution more scientifically. In the air pollutant concentration prediction module, a novel hybridization model combining complementary ensemble empirical mode decomposition, a modified cuckoo search and differential evolution algorithm, and an Elman neural network, is proposed to improve the forecasting accuracy of six main air pollutant concentrations. To verify the effectiveness of this system, pollutant data for two cities in China are used. The result of the fuzzy comprehensive evaluation shows that the major air pollutants in Xi'an and Jinan are PM 10 and PM 2.5 respectively, and that the air quality of Xi'an is better than that of Jinan. The forecasting results indicate that the proposed hybrid model is remarkably superior to all benchmark models on account of its higher prediction accuracy and stability. Copyright © 2017 Elsevier Inc. All rights reserved.

Reduction of the environmental concentration of air pollutants by proper geometrical orientation of industrial line sources

International Nuclear Information System (INIS)

Tadmor, J.

1980-01-01

An account is given of an Israeli study of two line sources, one composed of 10 and the other of 20 individual sources. The height of release ranged from 15.7 to 39.6 m, with a uniform rate of release of a gaseous pollutant of 1 Ci/s for each source. Average pollutant concentration was plotted as a function of the rotation angle of the line sources. Reduction of pollutant concentration by a particular rotation of the line sources attained values of up to 50%. At certain rotation angles of the line sources, the environmental concentration was lower even as compared with a single high source. Results also depended on atmospheric conditions. It is suggested that considering the increase in cost of augmenting the height of release as a means of reducing the air pollutant concentration, determination of the optimum geometric orientation of the line sources should be considered as an economical means of improving environmental air quality. (U.K.)

Photochemical smog pollution in the Bangkok Metropolitan Region of Thailand in relation to O 3 precursor concentrations and meteorological conditions

Science.gov (United States)

Zhang, B.-N.; Kim Oanh, N. T.

Analysis of photochemical pollution was done using the available 5-yr monitoring data (1996-2000) from 11 monitoring stations in Bangkok and 5 stations in other surrounding provinces, i.e. the Bangkok Metropolitan Region (BMR). Status and trend of O 3 as well as the monthly and diurnal variations were analyzed in relation to the local meteorological conditions as well as the regional transport of pollutants associated with the monsoon. The O 3 in Bangkok was found to be typical for the polluted urban areas with a lower concentration in the city center, especially at curbside stations, and higher concentration at the downwind locations. O 3 pollution was highest in 1997 with the maximum hourly average of 370 ppbv and the total hours exceeding the national hourly O 3 standard (100 ppbv) of 314 h, which is most likely related to the strong El Niño and the forest fire in Southeast Asia in this year. Meteorology-unadjusted trend shows a slight increase in O 3 from 1998 to 2000. Local emission and photochemistry are mainly responsible for O 3 episodes in the BMR. Seasonal fluctuations of O 3, however, were found to relate to the regional transport associated with the Asian monsoon. Highest O 3 pollution was found in the period from January to April (winter and local summer) and lowest during mid-rainy season, August. The O 3 increase isopleth diagram was constructed which shows that O 3 production in BMR is effective when the NO x/NMHC ratio is in the range of 0.04-0.15 with optimum ratio of around 0.07. Seasonal variations in NO x/NMHC ratios are consistent with the O 3 variations, i.e., optimum in summer (0.07), followed by winter (0.05), and the lowest in rainy season (0.03).

Prediction of Air Pollutants Concentration Based on an Extreme Learning Machine: The Case of Hong Kong.

Science.gov (United States)

Zhang, Jiangshe; Ding, Weifu

2017-01-24

With the development of the economy and society all over the world, most metropolitan cities are experiencing elevated concentrations of ground-level air pollutants. It is urgent to predict and evaluate the concentration of air pollutants for some local environmental or health agencies. Feed-forward artificial neural networks have been widely used in the prediction of air pollutants concentration. However, there are some drawbacks, such as the low convergence rate and the local minimum. The extreme learning machine for single hidden layer feed-forward neural networks tends to provide good generalization performance at an extremely fast learning speed. The major sources of air pollutants in Hong Kong are mobile, stationary, and from trans-boundary sources. We propose predicting the concentration of air pollutants by the use of trained extreme learning machines based on the data obtained from eight air quality parameters in two monitoring stations, including Sham Shui Po and Tap Mun in Hong Kong for six years. The experimental results show that our proposed algorithm performs better on the Hong Kong data both quantitatively and qualitatively. Particularly, our algorithm shows better predictive ability, with R 2 increased and root mean square error values decreased respectively.

Prediction of Air Pollutants Concentration Based on an Extreme Learning Machine: The Case of Hong Kong

Directory of Open Access Journals (Sweden)

Jiangshe Zhang

2017-01-01

Full Text Available With the development of the economy and society all over the world, most metropolitan cities are experiencing elevated concentrations of ground-level air pollutants. It is urgent to predict and evaluate the concentration of air pollutants for some local environmental or health agencies. Feed-forward artificial neural networks have been widely used in the prediction of air pollutants concentration. However, there are some drawbacks, such as the low convergence rate and the local minimum. The extreme learning machine for single hidden layer feed-forward neural networks tends to provide good generalization performance at an extremely fast learning speed. The major sources of air pollutants in Hong Kong are mobile, stationary, and from trans-boundary sources. We propose predicting the concentration of air pollutants by the use of trained extreme learning machines based on the data obtained from eight air quality parameters in two monitoring stations, including Sham Shui Po and Tap Mun in Hong Kong for six years. The experimental results show that our proposed algorithm performs better on the Hong Kong data both quantitatively and qualitatively. Particularly, our algorithm shows better predictive ability, with R 2 increased and root mean square error values decreased respectively.

Association of lead concentration in colostrum, maternal and cord blood with newborn weight in polluted vs. non-polluted areas of Iran

Directory of Open Access Journals (Sweden)

Golmohammadi T.

2007-10-01

Full Text Available Background: Lead poisoning has proven to be one of the most important environmental health problems among developing countries with both direct and indirect effects on human life. Lead is known to cross the blood-brain barrier and placenta, and accumulates in soft and hard tissues. Lead can be excreted in urine, stool, milk, sweat, nails and saliva. During pregnancy and lactation, lead is released from bones into the blood along with Ca2+. The toxic effects of lead on various human tissues have been studied extensively, but few studies have addressed its impact on fetal development during pregnancy. Blood levels of lead are higher in people living in lead-polluted regions. It has been reported that Tehran (central and southern parts is the most problematic city in terms of lead poisoning.Methods: From 86 sets of mothers and newborns in a non-polluted area of rural Rasht, Iran, we examined specimens of maternal blood, cord blood and colostrum (86×3=258 and specimens from 85 sets of mothers and newborns in a polluted area of Tehran, Iran (85×3=255 for lead levels using atomic absorption spectrophotometry (AAS and analyzed the results by t-test, SPSS, and linear regression.Results: The mean blood lead concentrations of mothers, cord blood of newborns and colostrum were 7.6±4.1, 5.9±3 and 4.2±2.5 μg/dl, respectively, in the non-polluted area and 9.1±8.4, 6.5±5.2 and 5.8±5.5 μg/dl, respectively, in the polluted area. The mean weights of the newborns in non-polluted and polluted areas were 3.2±0.5 kg and 3.2±4.5 kg, respectively.Conclusions: Our data revealed an association between mean concentrations in blood lead of mothers and newborns and between mean concentrations of colostrum lead and newborn blood lead in both areas (p=0.01. There was no association between mean blood lead concentration of mothers with the weight of their newborns (p=0.89.

Persistent organic pollutant concentrations in first birth mothers across Mexico.

Science.gov (United States)

Rodríguez-Dozal, Sandra; Riojas Rodríguez, Horacio; Hernández-Ávila, Mauricio; Van Oostdam, Jay; Weber, Jean Philippe; Needham, Larry L; Trip, Luke

2012-01-01

This project was initiated by the North America Commission for Environmental Cooperation (CEC). Its main purpose was to obtain an initial profile on pregnant woman's exposure to persistent organic pollutants (POPs) in North America (Canada, the United States and Mexico). Persistent organic pollutants are transferred to the fetus via the placenta during the pregnancy or to the infant via maternal milk; therefore, the pregnant woman's body burden is important because of the higher exposures and potential health effects in the fetus and infant. This paper presents the results from 240 pregnant women in 10 Mexican cities, and includes the concentrations of various POPs such as polychlorinated biphenyls (PCBs), organochlorine pesticides and polychlorinated dibenzo dioxins and furans (PCDDs and PCDFs) in maternal plasma. We found concentrations of p,p'-DDE in maternal samples from Coatzacoalcos to be ∼60% higher than those found in Ciudad Obregon, which had the second highest concentration. Pregnant women from Merida had higher mean concentrations of PCBs than all women in other regions. Results for PCDDs and PCDFs plus dioxin-like PCBs data were only available on the basis of composite samples, and their concentrations are similar in most cities except for Coatzacoalcos, which had more than double the concentration found in other cities. Although this study provides useful information on the variability of POPs in specific populations and possible regional/local differences, these results cannot be generalized to the entire Mexican population because of differences in age, gender, sources of exposure and nonrandom nature of the sample.

Ice-nucleating particle concentrations unaffected by urban air pollution in Beijing, China

Science.gov (United States)

Chen, Jie; Wu, Zhijun; Augustin-Bauditz, Stefanie; Grawe, Sarah; Hartmann, Markus; Pei, Xiangyu; Liu, Zirui; Ji, Dongsheng; Wex, Heike

2018-03-01

Exceedingly high levels of PM2.5 with complex chemical composition occur frequently in China. It has been speculated whether anthropogenic PM2.5 may significantly contribute to ice-nucleating particles (INP). However, few studies have focused on the ice-nucleating properties of urban particles. In this work, two ice-nucleating droplet arrays have been used to determine the atmospheric number concentration of INP (NINP) in the range from -6 to -25 °C in Beijing. No correlations between NINP and either PM2.5 or black carbon mass concentrations were found, although both varied by more than a factor of 30 during the sampling period. Similarly, there were no correlations between NINP and either total particle number concentration or number concentrations for particles with diameters > 500 nm. Furthermore, there was no clear difference between day and night samples. All these results indicate that Beijing air pollution did not increase or decrease INP concentrations in the examined temperature range above values observed in nonurban areas; hence, the background INP concentrations might not be anthropogenically influenced as far as urban air pollution is concerned, at least in the examined temperature range.

Lactation history, serum concentrations of persistent organic pollutants, and maternal risk of diabetes

DEFF Research Database (Denmark)

Zong, Geng; Grandjean, Philippe; Wang, Xiaobin

2016-01-01

OBJECTIVE: Lactation may help curb diabetes risk and is also known as an excretion route for some environmental pollutants. We evaluated associations of lifetime lactation history with serum concentrations of persistent organic pollutants (POPs) in the National Health and Nutrition Examination....... Prospective studies are needed to clarify how lactation could complement diabetes prevention through decreasing the POP body burdens....

Secondary poisoning of cadmium, copper and mercury: implications for the Maximum Permissible Concentrations and Negligible Concentrations in water, sediment and soil

NARCIS (Netherlands)

Smit CE; Wezel AP van; Jager T; Traas TP; CSR

2000-01-01

The impact of secondary poisoning on the Maximum Permissible Concentrations (MPCs) and Negligible Concentrations (NCs) of cadmium, copper and mercury in water, sediment and soil have been evaluated. Field data on accumulation of these elements by fish, mussels and earthworms were used to derive

Maximum solid concentrations of coal water slurries predicted by neural network models

Energy Technology Data Exchange (ETDEWEB)

Cheng, Jun; Li, Yanchang; Zhou, Junhu; Liu, Jianzhong; Cen, Kefa

2010-12-15

The nonlinear back-propagation (BP) neural network models were developed to predict the maximum solid concentration of coal water slurry (CWS) which is a substitute for oil fuel, based on physicochemical properties of 37 typical Chinese coals. The Levenberg-Marquardt algorithm was used to train five BP neural network models with different input factors. The data pretreatment method, learning rate and hidden neuron number were optimized by training models. It is found that the Hardgrove grindability index (HGI), moisture and coalification degree of parent coal are 3 indispensable factors for the prediction of CWS maximum solid concentration. Each BP neural network model gives a more accurate prediction result than the traditional polynomial regression equation. The BP neural network model with 3 input factors of HGI, moisture and oxygen/carbon ratio gives the smallest mean absolute error of 0.40%, which is much lower than that of 1.15% given by the traditional polynomial regression equation. (author)

Polluted soil leaching: unsaturated conditions and flow rate effects

Directory of Open Access Journals (Sweden)

Chourouk Mathlouthi

2017-04-01

Full Text Available In this study, soil samples are extracted from a polluted site at different depths. Soils texture and pollutant presence are different with depth. Preliminary analyzes showed pollution by heavy metals. To simulate soil leaching operation in static condition, a series of leaching tests are conducted in laboratory column under conditions of upflow unsaturated soil. Electrical conductivity and pH measurements on the recovered leachate are performed. Different flow rates are tested. Comparison of different profiles shows that the dissolved pollutants are concentrated in the upper soil levels and disperse weakly in the lower parts which confirm the nature of anthropogenic pollution of heavy metals. Water mobilizes a high amount of dissolved ionic substances up to 80% of the initial concentration. The increase in flow rate requires more pore volume injected to achieve the maximum clearance rate. The down flow condition extracts a small amount of dissolved substances.

A joint prevention and control mechanism for air pollution in the Beijing-Tianjin-Hebei region in china based on long-term and massive data mining of pollutant concentration

Science.gov (United States)

Wang, Hongbo; Zhao, Laijun

2018-02-01

China's Beijing-Tianjin-Hebei (BTH) region suffers from the country's worst air pollution. The problem has caused widespread concern both at home and abroad. Based on long-term and massive data mining of PM2.5 and PM10 concentration, we found that these pollutants showed similar variations in four seasons, but the most severe pollution was in winter. Through cluster analysis of the winter daily average concentration (DAC) of the two pollutants, we defined regions with similar variations in pollutant concentrations in winter. For the most polluted cities in BTH, the relationship between correlation coefficients for winter DAC and the distance between cities revealed that PM2.5 has regional, large-scale characteristics, with concentrated outbreaks, whereas PM10 has local, small-scale characteristics, with outbreaks at multiple locations. By selecting the key cities with the strongest linear relationship between the pollutant's DAC of each city and the daily individual air quality index values of the BTH region and through cluster analysis on the correlations between the pollutant DACs of the key cities, we defined regional divisions suitable for Joint Prevention and Control of Atmospheric Pollution (JPCAP) program to control PM2.5 and PM10. Comprehensively considering the degree of influence of regional atmospheric pollution control (RAPC) on air quality in BTH, as well as the elasticity and urgency of RAPC, we defined the control grades of the JPCAP regions. We found both the regions and corresponding control grades were consistent for PM2.5 and PM10. The thinking and methods of atmospheric pollution control we proposed will have broad significance for implementation of RAPC in other regions around the world.

Assessing Health Impacts of Air Pollution in Kashan 2011

Directory of Open Access Journals (Sweden)

Masoud Motalleby

2015-08-01

Full Text Available Abstract Background: The air pollutants such as CO, SO2, NO2, O3, and particulate matters have harmful effects on public health. Determination of the actual concentration of the pollutants and description of air quantity and quality contents in comparison of standard conditions and timely informing people to regulate control programs is essential. Kashan is exposed to the winds contain-ing the suspended particulate matters due to the proximity of the desert. Moreover, the growth of population, factories and industries in the city are artifical resources of the air pollution. Hence, assessment and monitoring of air pollution standard condition in kashan is crucial. Materials and Methods: In this cross-sectional and descriptive study, the concentration of CO, SO2, NO2, O3, and suspended particulate matters less than 10 microns (PM10 measured according to WHO standards in Panzdah-e-Khordad station of Kashan in 2011. The annual mean and maximum rates, the mean and maximum rate of summer and winter, and annual percentile 98%, determined for each pollutant and used in AirQ software. Then, the number of death and disease attributed to each pollutant was calculated. Results: The results demonstrate that the cumulative number of deaths attributed to PM10, NO2, SO2, and O3 was 100, 22, 82, and 54, respectively. Conclusion: In total, the suspended particulate matters have the most effects on death and disease resulted from the air pollution. Hence, managing the resources of particulate matters and SO2 pollutants has many effects on reducing the adverse health effects of air pollution in Kashan.

Effects of Roof-Edge Roughness on Air Temperature and Pollutant Concentration in Urban Canyons

Science.gov (United States)

Aliabadi, Amir A.; Krayenhoff, E. Scott; Nazarian, Negin; Chew, Lup Wai; Armstrong, Peter R.; Afshari, Afshin; Norford, Leslie K.

2017-08-01

The influence of roof-edge roughness elements on airflow, heat transfer, and street-level pollutant transport inside and above a two-dimensional urban canyon is analyzed using an urban energy balance model coupled to a large-eddy simulation model. Simulations are performed for cold (early morning) and hot (mid afternoon) periods during the hottest month of the year (August) for the climate of Abu Dhabi, United Arab Emirates. The analysis suggests that early in the morning, and when the tallest roughness elements are implemented, the temperature above the street level increases on average by 0.5 K, while the pollutant concentration decreases by 2% of the street-level concentration. For the same conditions in mid afternoon, the temperature decreases conservatively by 1 K, while the pollutant concentration increases by 7% of the street-level concentration. As a passive or active architectural solution, the roof roughness element shows promise for improving thermal comfort and air quality in the canyon for specific times, but this should be further verified experimentally. The results also warrant a closer look at the effects of mid-range roughness elements in the urban morphology on atmospheric dynamics so as to improve parametrizations in mesoscale modelling.

Heavy metal concentrations in a soil-plant-snail food chain along a terrestrial soil pollution gradient

Energy Technology Data Exchange (ETDEWEB)

Notten, M.J.M. [Institute of Ecological Science, Department of Systems Ecology, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV, Amsterdam (Netherlands)]. E-mail: martje.notten@ecology.falw.vu.nl; Oosthoek, A.J.P. [Institute of Ecological Science, Department of Systems Ecology, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV, Amsterdam (Netherlands); Rozema, J. [Institute of Ecological Science, Department of Systems Ecology, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV, Amsterdam (Netherlands); Aerts, R. [Institute of Ecological Science, Department of Systems Ecology, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV, Amsterdam (Netherlands)

2005-11-15

We investigated concentrations of Zn, Cu, Cd and Pb in the compartments of a soil-plant (Urtica dioica)-snail (Cepaea nemoralis) food chain in four polluted locations in the Biesbosch floodplains, the Netherlands, and two reference locations. Total soil metal concentrations in the polluted locations were 4-20 times higher than those in the reference locations. Positive relationships between the generally low leaf concentrations and the soil concentrations were found for Zn only (r {sup 2} = 0.20). Bioaccumulation of Zn, Cu and Cd was observed in the snail tissues. We found positive relationships between the snail and leaf concentrations for all metals (range r {sup 2} = 0.19-0.46). The relationships between soil and snail concentrations were also positive, except for Cu (range r {sup 2} = 0.15-0.33). These results suggest transfer of metals to C. nemoralis snails from U. dioica leaves and from the soil. Metal transfer from polluted leaves to C. nemoralis is more important than transfer from the soil. - Bioaccumulation and positive snail-leaf relationships suggest metal transfer from Urtica dioica leaves to Cepaea nemoralis snails.

Heavy metal concentrations in a soil-plant-snail food chain along a terrestrial soil pollution gradient

International Nuclear Information System (INIS)

Notten, M.J.M.; Oosthoek, A.J.P.; Rozema, J.; Aerts, R.

2005-01-01

We investigated concentrations of Zn, Cu, Cd and Pb in the compartments of a soil-plant (Urtica dioica)-snail (Cepaea nemoralis) food chain in four polluted locations in the Biesbosch floodplains, the Netherlands, and two reference locations. Total soil metal concentrations in the polluted locations were 4-20 times higher than those in the reference locations. Positive relationships between the generally low leaf concentrations and the soil concentrations were found for Zn only (r 2 = 0.20). Bioaccumulation of Zn, Cu and Cd was observed in the snail tissues. We found positive relationships between the snail and leaf concentrations for all metals (range r 2 = 0.19-0.46). The relationships between soil and snail concentrations were also positive, except for Cu (range r 2 = 0.15-0.33). These results suggest transfer of metals to C. nemoralis snails from U. dioica leaves and from the soil. Metal transfer from polluted leaves to C. nemoralis is more important than transfer from the soil. - Bioaccumulation and positive snail-leaf relationships suggest metal transfer from Urtica dioica leaves to Cepaea nemoralis snails

Total vs. internal element concentrations in Scots pine needles along a sulphur and metal pollution gradient

International Nuclear Information System (INIS)

Rautio, Pasi; Huttunen, Satu

2003-01-01

Different methods should be used for foliar analyses of trees used as bioindicators of pollution, than those analyses used in nutritional studies of trees. - Analysis of foliar elements is a commonly used method for studying tree nutrition and for monitoring the impacts of air pollutants on forest ecosystems. Interpretations based on the results of foliar element analysis may, however, be different in nutrition vs. monitoring studies. We studied the impacts of severe sulphur and metal (mainly Cu and Ni) pollution on the element concentrations (Al, Ca, Cu, Fe, K, Mg, Mn, Ni, P, Pb, S and Zn) in Scots pine (Pinus sylvestris L.) foliage along an airborne sulphur and metal pollution gradient. Emphasis was put on determining the contribution of air-borne particles that have accumulated on needle surfaces to the total foliage concentrations. A comparison of two soil extraction methods was carried out in order to obtain a reliable estimate of plant-available element concentrations in the soil. Element concentrations in the soil showed only a weak relationship with internal foliar concentrations. There were no clear differences between the total and internal needle S concentrations along the gradient, whereas at the plot closest to the metal smelter complex the total Cu concentrations in the youngest needles were 1.3-fold and Ni concentrations over 1.6-fold higher than the internal needle concentrations. Chloroform-extracted surface wax was found to have Ni and Cu concentrations of as high as 3000 and 600 μg/g of wax, respectively. Our results suggest that bioindicator studies (e.g. monitoring studies) may require different foliar analysis techniques from those used in studies on the nutritional status of trees

Assessment of atmospheric pollution in the city of Naberezhnye ...

African Journals Online (AJOL)

By the nature of spatial distribution, two distinctly different groups of pollutants were defined: mainly contained in emissions of industrial enterprises, and coming into the atmospheric air, mainly with emissions from automotive transport. Keywords: emissions fromautomotive transport, maximum permissible concentration, ...

Windows pollution problems of the dust concentration measurement based on scattering method

International Nuclear Information System (INIS)

Zhao Yanjun; Zhang Yongtao; Shi Xinyue; Xu Chuanlong; Wang Shimin

2009-01-01

The windows are separated the measurement system from the dust space in the light Scattering dust concentration measurement system. The windows are polluted unavoidably by the dust and the measurement error is produced. Based on the Mie Scattering theory, the measurement error is researched in this paper. The numerical simulation results show that the measurement error is related to the particles diameter distribution and the refractive index, but is independent of the particles average diameter. A novel photoelectricity sensor is developed in this paper in order to solve the measurement error by the windows pollution. The calculated method is brought out which can amend the measurement errors by the windows pollution and improve the measurement accuracy.

Sensing sulfur oxides and other sulfur bearing pollutants with solid electrolyte pellets. I. Gas concentration cells

Energy Technology Data Exchange (ETDEWEB)

Chamberland, A M; Gauthier, J M

1977-01-01

A new sensing technique using a solid electrolyte has been demonstrated for sulfur-bearing pollutants. Based on potentiometric measurements across a pellet of potassium sulfate, this sensor allows concentrations of sulfur dioxides, sulfur trioxide, hydrogen sulfide, methyl mercaptan and carbonyl sulfide in air to be measured with accuracy. Its operational concentration range at the present time is 0.1 ppM up to at least 10,000 ppM. The presence of other common pollutants such as carbon dioxide, methane, nitric oxide and nitrogen dioxide does not interfere with the measurement of air samples containing sulfur-bearing pollutants.

Metal concentrations in homing pigeon lung tissue as a biomonitor of atmospheric pollution.

Science.gov (United States)

Cui, Jia; Halbrook, Richard S; Zang, Shuying; Han, Shuang; Li, Xinyu

2018-03-01

Atmospheric pollution in urban areas is a major worldwide concern with potential adverse impacts on wildlife and humans. Biomonitoring can provide direct evidence of the bioavailability and bioaccumulation of toxic metals in the environment that is not available with mechanical air monitoring. The current study continues our evaluation of the usefulness of homing pigeon lung tissue as a biomonitor of atmospheric pollution. Homing pigeons (1-2, 5-6, and 9-10+ year old (yo)) collected from Guangzhou during 2015 were necropsied and concentrations of cadmium (Cd), lead (Pb), and mercury (Hg) were measured in lung tissue. Lung Cd and Pb concentrations were significantly greater in 9-10+-year-old pigeons compared with those in other age groups, indicating their bioavailability and bioaccumulation. Lung Pb and Cd concentrations measured in 5-yo pigeons collected from Guangzhou during 2015 were significantly lower than concentrations reported in 5-yo homing pigeons collected from Guangzhou during 2011 and correlated with concentrations measured using mechanical air monitoring. In addition to temporal differences, spatial differences in concentrations of Cd, Pb, and Hg reported in ambient air samples and in pigeon lung tissues collected from Beijing and Guangzhou are discussed.

Gas sampling method for determining pollutant concentrations in the flame zone of two swirl-can combustor modules

Science.gov (United States)

Duerr, R. A.

1975-01-01

A gas sampling probe and traversing mechanism were developed to obtain detailed measurements of gaseous pollutant concentrations in the primary and mixing regions of combustors in order to better understand how pollutants are formed. The gas sampling probe was actuated by a three-degree-of-freedom traversing mechanism and the samples obtained were analyzed by an on-line gas analysis system. The pollutants in the flame zone of two different swirl-can combustor modules were measured at an inlet-air temperature of 590 K, pressure of 6 atmospheres, and reference velocities of 23 and 30 meters per second at a fuel-air ratio of 0.02. Typical results show large spatial gradients in the gaseous pollutant concentration close to the swirl-can module. Average concentrations of unburned hydrocarbons and carbon monoxide decrease rapidly in the downstream wake regions of each module. By careful and detailed probing, the effect of various module design features on pollutant formation can be assessed. The techniques presently developed seem adequate to obtain the desired information.

Air pollutant concentrations near three Texas roadways, Part I: Ultrafine particles

Science.gov (United States)

Zhu, Yifang; Pudota, Jayanth; Collins, Donald; Allen, David; Clements, Andrea; DenBleyker, Allison; Fraser, Matt; Jia, Yuling; McDonald-Buller, Elena; Michel, Edward

Vehicular emitted air pollutant concentrations were studied near three types of roadways in Austin, Texas: (1) State Highway 71 (SH-71), a heavily traveled arterial highway dominated by passenger vehicles; (2) Interstate 35 (I-35), a limited access highway north of Austin in Georgetown; and (3) Farm to Market Road 973 (FM-973), a heavily traveled surface roadway dominated by truck traffic. Air pollutants examined include carbon monoxide (CO), oxides of nitrogen (NO x), and carbonyl species in the gas-phase. In the particle phase, ultrafine particle (UFP) concentrations (diameter road were found to be the most important factors determining UFP concentrations near the roadways. Since wind directions were not consistent during the sampling periods, distances along wind trajectories from the roadway to the sampling points were used to study the decay characteristics of UFPs. Under perpendicular wind conditions, for all studied roadway types, particle number concentrations increased dramatically moving from the upwind side to the downwind side. The elevated particle number concentrations decay exponentially with increasing distances from the roadway with sharp concentration gradients observed within 100-150 m, similar to previously reported studies. A single exponential decay curve was found to fit the data collected from all three roadways very well under perpendicular wind conditions. No consistent pattern was observed for UFPs under parallel wind conditions. However, regardless of wind conditions, particle concentrations returned to background levels within a few hundred meters of the roadway. Within measured UFP size ranges, smaller particles (6-25 nm) decayed faster than larger ones (100-300 nm). Similar decay rates were observed among UFP number, surface, and volume.

Assessment of sampling strategies for estimation of site mean concentrations of stormwater pollutants.

Science.gov (United States)

McCarthy, David T; Zhang, Kefeng; Westerlund, Camilla; Viklander, Maria; Bertrand-Krajewski, Jean-Luc; Fletcher, Tim D; Deletic, Ana

2018-02-01

The estimation of stormwater pollutant concentrations is a primary requirement of integrated urban water management. In order to determine effective sampling strategies for estimating pollutant concentrations, data from extensive field measurements at seven different catchments was used. At all sites, 1-min resolution continuous flow measurements, as well as flow-weighted samples, were taken and analysed for total suspend solids (TSS), total nitrogen (TN) and Escherichia coli (E. coli). For each of these parameters, the data was used to calculate the Event Mean Concentrations (EMCs) for each event. The measured Site Mean Concentrations (SMCs) were taken as the volume-weighted average of these EMCs for each parameter, at each site. 17 different sampling strategies, including random and fixed strategies were tested to estimate SMCs, which were compared with the measured SMCs. The ratios of estimated/measured SMCs were further analysed to determine the most effective sampling strategies. Results indicate that the random sampling strategies were the most promising method in reproducing SMCs for TSS and TN, while some fixed sampling strategies were better for estimating the SMC of E. coli. The differences in taking one, two or three random samples were small (up to 20% for TSS, and 10% for TN and E. coli), indicating that there is little benefit in investing in collection of more than one sample per event if attempting to estimate the SMC through monitoring of multiple events. It was estimated that an average of 27 events across the studied catchments are needed for characterising SMCs of TSS with a 90% confidence interval (CI) width of 1.0, followed by E.coli (average 12 events) and TN (average 11 events). The coefficient of variation of pollutant concentrations was linearly and significantly correlated to the 90% confidence interval ratio of the estimated/measured SMCs (R 2  = 0.49; P sampling frequency needed to accurately estimate SMCs of pollutants. Crown

Characterizing the spatial variability of local and background concentration signals for air pollution at the neighbourhood scale

Science.gov (United States)

Shairsingh, Kerolyn K.; Jeong, Cheol-Heon; Wang, Jonathan M.; Evans, Greg J.

2018-06-01

Vehicle emissions represent a major source of air pollution in urban districts, producing highly variable concentrations of some pollutants within cities. The main goal of this study was to identify a deconvolving method so as to characterize variability in local, neighbourhood and regional background concentration signals. This method was validated by examining how traffic-related and non-traffic-related sources influenced the different signals. Sampling with a mobile monitoring platform was conducted across the Greater Toronto Area over a seven-day period during summer 2015. This mobile monitoring platform was equipped with instruments for measuring a wide range of pollutants at time resolutions of 1 s (ultrafine particles, black carbon) to 20 s (nitric oxide, nitrogen oxides). The monitored neighbourhoods were selected based on their land use categories (e.g. industrial, commercial, parks and residential areas). The high time-resolution data allowed pollutant concentrations to be separated into signals representing background and local concentrations. The background signals were determined using a spline of minimums; local signals were derived by subtracting the background concentration from the total concentration. Our study showed that temporal scales of 500 s and 2400 s were associated with the neighbourhood and regional background signals respectively. The percent contribution of the pollutant concentration that was attributed to local signals was highest for nitric oxide (NO) (37-95%) and lowest for ultrafine particles (9-58%); the ultrafine particles were predominantly regional (32-87%) in origin on these days. Local concentrations showed stronger associations than total concentrations with traffic intensity in a 100 m buffer (ρ:0.21-0.44). The neighbourhood scale signal also showed stronger associations with industrial facilities than the total concentrations. Given that the signals show stronger associations with different land use suggests that

Evaluation of maximum radionuclide concentration from decay chains migration in aquifers

International Nuclear Information System (INIS)

Aquino Branco, O.E. de.

1983-01-01

The mathematical formulation of the mechanisms involved in the transport of contaminants in aquifers is presented. The methodology employed is described. A method of calculation the maximum concentration of radionuclides migrating in the underground water, and resulting from one decay chain, is then proposed. As an example, the methodology is applied to a waste basin, built to receive effluents from a hypothectical uranium ore mining and milling facility. (M.A.C.) [pt

A study of the physical factors affecting air pollution dispersion in Helwan

International Nuclear Information System (INIS)

Megahed, A.A.

1992-01-01

Air pollution is considered as one of the most important environmental problems facing the humanity. Cement industry, usually, is responsible for building high levels of pollutants. The present research focused on the study of air pollution control of cement industry using mathematical modeling. A mathematical dispersion model was developed based on Gaussian distribution where the dispersion parameters increase with increasing atmospheric turbulence. The Gaussian equation takes in consideration the effect of emission rates. stack height, buoyant plume rise, weather and meteorological parameters. The model was tested for different stack heights, wind speeds. And atmospheric stability classes. Maximum ground level concentration of cement pollutants were measured in different locations of Helwan, south Cairo around the cement factories. Analysis of results shows that the ground level of pollutants concentrations are inversely proportional to wind speed and atmospheric stability classes. Stack height also affects the behaviour of deposition of cement particulates. The model results show satisfactory agreement with the measured concentrations. 6 figs

Soil TPH Concentration Estimation Using Vegetation Indices in an Oil Polluted Area of Eastern China

Science.gov (United States)

Zhu, Linhai; Zhao, Xuechun; Lai, Liming; Wang, Jianjian; Jiang, Lianhe; Ding, Jinzhi; Liu, Nanxi; Yu, Yunjiang; Li, Junsheng; Xiao, Nengwen; Zheng, Yuanrun; Rimmington, Glyn M.

2013-01-01

Assessing oil pollution using traditional field-based methods over large areas is difficult and expensive. Remote sensing technologies with good spatial and temporal coverage might provide an alternative for monitoring oil pollution by recording the spectral signals of plants growing in polluted soils. Total petroleum hydrocarbon concentrations of soils and the hyperspectral canopy reflectance were measured in wetlands dominated by reeds (Phragmites australis) around oil wells that have been producing oil for approximately 10 years in the Yellow River Delta, eastern China to evaluate the potential of vegetation indices and red edge parameters to estimate soil oil pollution. The detrimental effect of oil pollution on reed communities was confirmed by the evidence that the aboveground biomass decreased from 1076.5 g m−2 to 5.3 g m−2 with increasing total petroleum hydrocarbon concentrations ranging from 9.45 mg kg−1 to 652 mg kg−1. The modified chlorophyll absorption ratio index (MCARI) best estimated soil TPH concentration among 20 vegetation indices. The linear model involving MCARI had the highest coefficient of determination (R 2 = 0.73) and accuracy of prediction (RMSE = 104.2 mg kg−1). For other vegetation indices and red edge parameters, the R2 and RMSE values ranged from 0.64 to 0.71 and from 120.2 mg kg−1 to 106.8 mg kg−1 respectively. The traditional broadband normalized difference vegetation index (NDVI), one of the broadband multispectral vegetation indices (BMVIs), produced a prediction (R 2 = 0.70 and RMSE = 110.1 mg kg−1) similar to that of MCARI. These results corroborated the potential of remote sensing for assessing soil oil pollution in large areas. Traditional BMVIs are still of great value in monitoring soil oil pollution when hyperspectral data are unavailable. PMID:23342066

Long short-term memory neural network for air pollutant concentration predictions: Method development and evaluation.

Science.gov (United States)

Li, Xiang; Peng, Ling; Yao, Xiaojing; Cui, Shaolong; Hu, Yuan; You, Chengzeng; Chi, Tianhe

2017-12-01

Air pollutant concentration forecasting is an effective method of protecting public health by providing an early warning against harmful air pollutants. However, existing methods of air pollutant concentration prediction fail to effectively model long-term dependencies, and most neglect spatial correlations. In this paper, a novel long short-term memory neural network extended (LSTME) model that inherently considers spatiotemporal correlations is proposed for air pollutant concentration prediction. Long short-term memory (LSTM) layers were used to automatically extract inherent useful features from historical air pollutant data, and auxiliary data, including meteorological data and time stamp data, were merged into the proposed model to enhance the performance. Hourly PM 2.5 (particulate matter with an aerodynamic diameter less than or equal to 2.5 μm) concentration data collected at 12 air quality monitoring stations in Beijing City from Jan/01/2014 to May/28/2016 were used to validate the effectiveness of the proposed LSTME model. Experiments were performed using the spatiotemporal deep learning (STDL) model, the time delay neural network (TDNN) model, the autoregressive moving average (ARMA) model, the support vector regression (SVR) model, and the traditional LSTM NN model, and a comparison of the results demonstrated that the LSTME model is superior to the other statistics-based models. Additionally, the use of auxiliary data improved model performance. For the one-hour prediction tasks, the proposed model performed well and exhibited a mean absolute percentage error (MAPE) of 11.93%. In addition, we conducted multiscale predictions over different time spans and achieved satisfactory performance, even for 13-24 h prediction tasks (MAPE = 31.47%). Copyright © 2017 Elsevier Ltd. All rights reserved.

Elevated tropospheric CO2 and O3 concentrations impair organic pollutant removal from grassland soil.

Science.gov (United States)

Ai, Fuxun; Eisenhauer, Nico; Jousset, Alexandre; Butenschoen, Olaf; Ji, Rong; Guo, Hongyan

2018-04-03

The concentrations of tropospheric CO 2 and O 3 have been rising due to human activities. These rising concentrations may have strong impacts on soil functions as changes in plant physiology may lead to altered plant-soil interactions. Here, the effects of eCO 2 and eO 3 on the removal of polycyclic aromatic hydrocarbon (PAH) pollutants in grassland soil were studied. Both elevated CO 2 and O 3 concentrations decreased PAH removal with lowest removal rates at elevated CO 2 and elevated O 3 concentrations. This effect was linked to a shift in soil microbial community structure by structural equation modeling. Elevated CO 2 and O 3 concentrations reduced the abundance of gram-positive bacteria, which were tightly linked to soil enzyme production and PAH degradation. Although plant diversity did not buffer CO 2 and O 3 effects, certain soil microbial communities and functions were affected by plant communities, indicating the potential for longer-term phytoremediation approaches. Results of this study show that elevated CO 2 and O 3 concentrations may compromise the ability of soils to degrade organic pollutants. On the other hand, the present study also indicates that the targeted assembly of plant communities may be a promising tool to shape soil microbial communities for the degradation of organic pollutants in a changing world.

On the environmental pollution and radioactivity within the territory of Russia in October, 1992

International Nuclear Information System (INIS)

Ovanesyants, A.M.; Belova, N.A.; Ivanov, M.N.

1993-01-01

Points of Russia were indicated where the maximum permissible concentration limits of pollutants were found to be exceeded. Causes of the observed incidents were described. Pollution of the atmospheric air, soils and surface waters was presented for the october, 1992. Daily concentrations of the radioactive aerosols in the atmospheric air were equal to the background values as well as their fallout. High radioactivity in Chita and Rostov cities were explaned by natural origin factors (meteorological conditions)

Determinants of perceived air pollution annoyance and association between annoyance scores and air pollution (PM 2.5, NO 2) concentrations in the European EXPOLIS study

Science.gov (United States)

Rotko, Tuulia; Oglesby, Lucy; Künzli, Nino; Carrer, Paolo; Nieuwenhuijsen, Mark J.; Jantunen, Matti

Apart from its traditionally considered objective impacts on health, air pollution can also have perceived effects, such as annoyance. The psychological effects of air pollution may often be more important to well-being than the biophysical effects. Health effects of perceived annoyance from air pollution are so far unknown. More knowledge of air pollution annoyance levels, determinants and also associations with different air pollution components is needed. In the European air pollution exposure study, EXPOLIS, the air pollution annoyance as perceived at home, workplace and in traffic were surveyed among other study objectives. Overall 1736 randomly drawn 25-55-yr-old subjects participated in six cities (Athens, Basel, Milan, Oxford, Prague and Helsinki). Levels and predictors of individual perceived annoyances from air pollution were assessed. Instead of the usual air pollution concentrations at fixed monitoring sites, this paper compares the measured microenvironment concentrations and personal exposures of PM 2.5 and NO 2 to the perceived annoyance levels. A considerable proportion of the adults surveyed was annoyed by air pollution. Female gender, self-reported respiratory symptoms, downtown living and self-reported sensitivity to air pollution were directly associated with high air pollution annoyance score while in traffic, but smoking status, age or education level were not significantly associated. Population level annoyance averages correlated with the city average exposure levels of PM 2.5 and NO 2. A high correlation was observed between the personal 48-h PM 2.5 exposure and perceived annoyance at home as well as between the mean annoyance at work and both the average work indoor PM 2.5 and the personal work time PM 2.5 exposure. With the other significant determinants (gender, city code, home location) and home outdoor levels the model explained 14% (PM 2.5) and 19% (NO 2) of the variation in perceived air pollution annoyance in traffic. Compared to

An integrated Bayesian model for estimating the long-term health effects of air pollution by fusing modelled and measured pollution data: A case study of nitrogen dioxide concentrations in Scotland.

Science.gov (United States)

Huang, Guowen; Lee, Duncan; Scott, Marian

2015-01-01

The long-term health effects of air pollution can be estimated using a spatio-temporal ecological study, where the disease data are counts of hospital admissions from populations in small areal units at yearly intervals. Spatially representative pollution concentrations for each areal unit are typically estimated by applying Kriging to data from a sparse monitoring network, or by computing averages over grid level concentrations from an atmospheric dispersion model. We propose a novel fusion model for estimating spatially aggregated pollution concentrations using both the modelled and monitored data, and relate these concentrations to respiratory disease in a new study in Scotland between 2007 and 2011. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Land cover and air pollution are associated with asthma hospitalisations: A cross-sectional study.

Science.gov (United States)

Alcock, Ian; White, Mathew; Cherrie, Mark; Wheeler, Benedict; Taylor, Jonathon; McInnes, Rachel; Otte Im Kampe, Eveline; Vardoulakis, Sotiris; Sarran, Christophe; Soyiri, Ireneous; Fleming, Lora

2017-12-01

There is increasing policy interest in the potential for vegetation in urban areas to mitigate harmful effects of air pollution on respiratory health. We aimed to quantify relationships between tree and green space density and asthma-related hospitalisations, and explore how these varied with exposure to background air pollution concentrations. Population standardised asthma hospitalisation rates (1997-2012) for 26,455 urban residential areas of England were merged with area-level data on vegetation and background air pollutant concentrations. We fitted negative binomial regression models using maximum likelihood estimation to obtain estimates of asthma-vegetation relationships at different levels of pollutant exposure. Green space and gardens were associated with reductions in asthma hospitalisation when pollutant exposures were lower but had no significant association when pollutant exposures were higher. In contrast, tree density was associated with reduced asthma hospitalisation when pollutant exposures were higher but had no significant association when pollutant exposures were lower. We found differential effects of natural environments at high and low background pollutant concentrations. These findings can provide evidence for urban planning decisions which aim to leverage health co-benefits from environmental improvements. Copyright © 2017 Elsevier Ltd. All rights reserved.

Maximum permissible concentration (MPC) values for spontaneously fissioning radionuclides

International Nuclear Information System (INIS)

Ford, M.R.; Snyder, W.S.; Dillman, L.T.; Watson, S.B.

1976-01-01

The radiation hazards involved in handling certain of the transuranic nuclides that exhibit spontaneous fission as a mode of decay were reaccessed using recent advances in dosimetry and metabolic modeling. Maximum permissible concentration (MPC) values in air and water for occupational exposure (168 hr/week) were calculated for 244 Pu, 246 Cm, 248 Cm, 250 Cf, 252 Cf, 254 Cf, /sup 254m/Es, 255 Es, 254 Fm, and 256 Fm. The half-lives, branching ratios, and principal modes of decay of the parent-daughter members down to a member that makes a negligible contribution to the dose are given, and all daughters that make a significant contribution to the dose to body organs following inhalation or ingestion are included in the calculations. Dose commitments for body organs are also given

Measurements and predictors of on-road ultrafine particle concentrations and associated pollutants in Los Angeles

Energy Technology Data Exchange (ETDEWEB)

Fruin, S. [California Air Resources Board, Sacramento (United States); University of Southern California, Los Angeles (United States). Keck School of Medicine, Department of Preventive Medicine; Westerdahl, D.; Sax, T. [California Air Resources Board, Sacramento (United States); Sioutas, C. [University of Southern California, Los Angeles (United States). Civil and Environmental Engineering; Fine, P.M. [University of Southern California, Los Angeles (United States). Civil and Environmental Engineering; South Coast Air Quality Management District, Diamond Bar, CA (United States)

2008-01-15

Motor vehicles are the dominant source of oxides of nitrogen (NO{sub x}), particulate matter(PM), and certain air toxics (e.g., benzene, 1,3-butadiene) in urban areas. On roadways, motor vehicle-related pollutant concentrations are typically many times higher than ambient concentrations. Due to high air exchange rates typical of moving vehicles, this makes time spent in vehicles on roadways a major source of exposure. This paper presents on-road measurements for Los Angeles freeways and arterial roads taken from a zero-emission electric vehicle outfitted with real-time instruments. The objective was to characterize air pollutant concentrations on roadways and identify the factors associated with the highest concentrations. Our analysis demonstrated that on freeways, concentrations of ultrafine particles (UFPs), black carbon, nitric oxide, and PM-bound polycyclic aromatic hydrocarbons (PM-PAH) are generated primarily by diesel-powered vehicles, despite the relatively low fraction ({approx}6%) of diesel-powered vehicles on Los Angeles freeways. However, UFP concentrations on arterial roads appeared to be driven primarily by proximity to gasoline-powered vehicles undergoing hard accelerations. Concentrations were roughly one-third of those on freeways. By using a multiple regression model for the freeway measurements, we were able to explain 60-70% of the variability in concentrations of UFP, black carbon, nitric oxide, and PM-PAH using measures of diesel truck density and hour of day (as an indicator of wind speed). Freeway concentrations of these pollutants were also well correlated wth readily available annual average daily truck counts, potentially allowing improved population exposure estimates for epidemiology studies. Based on these roadway measurements and average driving time, it appears that 33-45% of total UFP exposure for Los Angeles residents occurs due to time spent traveling in vehicles. (author)

Measurements and predictors of on-road ultrafine particle concentrations and associated pollutants in Los Angeles

International Nuclear Information System (INIS)

Fruin, S.; Sioutas, C.

2008-01-01

Motor vehicles are the dominant source of oxides of nitrogen (NO x ), particulate matter(PM), and certain air toxics (e.g., benzene, 1,3-butadiene) in urban areas. On roadways, motor vehicle-related pollutant concentrations are typically many times higher than ambient concentrations. Due to high air exchange rates typical of moving vehicles, this makes time spent in vehicles on roadways a major source of exposure. This paper presents on-road measurements for Los Angeles freeways and arterial roads taken from a zero-emission electric vehicle outfitted with real-time instruments. The objective was to characterize air pollutant concentrations on roadways and identify the factors associated with the highest concentrations. Our analysis demonstrated that on freeways, concentrations of ultrafine particles (UFPs), black carbon, nitric oxide, and PM-bound polycyclic aromatic hydrocarbons (PM-PAH) are generated primarily by diesel-powered vehicles, despite the relatively low fraction (∼6%) of diesel-powered vehicles on Los Angeles freeways. However, UFP concentrations on arterial roads appeared to be driven primarily by proximity to gasoline-powered vehicles undergoing hard accelerations. Concentrations were roughly one-third of those on freeways. By using a multiple regression model for the freeway measurements, we were able to explain 60-70% of the variability in concentrations of UFP, black carbon, nitric oxide, and PM-PAH using measures of diesel truck density and hour of day (as an indicator of wind speed). Freeway concentrations of these pollutants were also well correlated wth readily available annual average daily truck counts, potentially allowing improved population exposure estimates for epidemiology studies. Based on these roadway measurements and average driving time, it appears that 33-45% of total UFP exposure for Los Angeles residents occurs due to time spent traveling in vehicles. (author)

Measurements and predictors of on-road ultrafine particle concentrations and associated pollutants in Los Angeles

Science.gov (United States)

Fruin, S.; Westerdahl, D.; Sax, T.; Sioutas, C.; Fine, P. M.

Motor vehicles are the dominant source of oxides of nitrogen (NO x), particulate matter (PM), and certain air toxics (e.g., benzene, 1,3-butadiene) in urban areas. On roadways, motor vehicle-related pollutant concentrations are typically many times higher than ambient concentrations. Due to high air exchange rates typical of moving vehicles, this makes time spent in vehicles on roadways a major source of exposure. This paper presents on-road measurements for Los Angeles freeways and arterial roads taken from a zero-emission electric vehicle outfitted with real-time instruments. The objective was to characterize air pollutant concentrations on roadways and identify the factors associated with the highest concentrations. Our analysis demonstrated that on freeways, concentrations of ultrafine particles (UFPs), black carbon, nitric oxide, and PM-bound polycyclic aromatic hydrocarbons (PM-PAH) are generated primarily by diesel-powered vehicles, despite the relatively low fraction (˜6%) of diesel-powered vehicles on Los Angeles freeways. However, UFP concentrations on arterial roads appeared to be driven primarily by proximity to gasoline-powered vehicles undergoing hard accelerations. Concentrations were roughly one-third of those on freeways. By using a multiple regression model for the freeway measurements, we were able to explain 60-70% of the variability in concentrations of UFP, black carbon, nitric oxide, and PM-PAH using measures of diesel truck density and hour of day (as an indicator of wind speed). Freeway concentrations of these pollutants were also well correlated with readily available annual average daily truck counts, potentially allowing improved population exposure estimates for epidemiology studies. Based on these roadway measurements and average driving time, it appears that 33-45% of total UFP exposure for Los Angeles residents occurs due to time spent traveling in vehicles.

The influence of atmospheric circulation on the air pollution concentration and temperature inversion in Sosnowiec. Case study

Directory of Open Access Journals (Sweden)

Widawski Artur

2015-06-01

Full Text Available Sosnowiec is located in the Katowice Region, which is the most urbanized and industrialized region in Poland. Urban areas of such character favor enhancement of pollution concentration in the atmosphere and the consequent emergence of smog. Local meteorological and circulation conditions significantly influence not only on the air pollution level but also change air temperature considerably in their centers and immediate vicinities. The synoptic situation also plays the major role in dispersal and concentration of air pollutants and changes in temperature profile. One of the most important are the near-ground (100 m inversions of temperature revealed their highest values on clear winter days and sometimes stay still for the whole day and night. Air temperature inversions in Sosnowiec occur mainly during anticyclone stagnation (Ca-anticyclone centre and Ka-anticyclonic ridge and in anticyclones with air advection from the south and southwest (Sa and SWa which cause significantly increase of air pollution values. The detailed evaluation of the influence of circulation types on the appearance of a particular concentration of pollutants carried out in this work has confirmed the predominant influence of individual circulation types on the development of air pollution levels at the Katowice region. This paper presents research case study results of the thermal structure of the near-ground atmospheric layer (100 m and air pollution parameters (PM10, SO2, NO, NO2 changes in selected days of 2005 year according to regional synoptic circulation types. The changes in urban environment must be taken into account in analyses of multiyear trends of air temperature and air conditions on the regional and global scales.

Methods for Online Monitoring of Air Pollution Concentration

OpenAIRE

Ionel, Ioana; Popescu, Francisc

2010-01-01

Air pollution is a global environmental problem that represents a measure of the potential of the climate change rate influenced by local pollution sources, although its scale has a strong regional or local orientation. Improvements in technology supported by policy measures have lead to reduced pollution levels, but still, especially in new member states, more activity is needed. In developed countries advanced low pollution technique is applied in order to reduce the pollution levels Howeve...

A novel approach to estimating potential maximum heavy metal exposure to ship recycling yard workers in Alang, India

International Nuclear Information System (INIS)

Deshpande, Paritosh C.; Tilwankar, Atit K.; Asolekar, Shyam R.

2012-01-01

The 180 ship recycling yards located on Alang–Sosiya beach in the State of Gujarat on the west coast of India is the world's largest cluster engaged in dismantling. Yearly 350 ships have been dismantled (avg. 10,000 ton steel/ship) with the involvement of about 60,000 workers. Cutting and scrapping of plates or scraping of painted metal surfaces happens to be the commonly performed operation during ship breaking. The pollutants released from a typical plate-cutting operation can potentially either affect workers directly by contaminating the breathing zone (air pollution) or can potentially add pollution load into the intertidal zone and contaminate sediments when pollutants get emitted in the secondary working zone and gets subjected to tidal forces. There was a two-pronged purpose behind the mathematical modeling exercise performed in this study. First, to estimate the zone of influence up to which the effect of plume would extend. Second, to estimate the cumulative maximum concentration of heavy metals that can potentially occur in ambient atmosphere of a given yard. The cumulative maximum heavy metal concentration was predicted by the model to be between 113 μg/Nm 3 and 428 μg/Nm 3 (at 4 m/s and 1 m/s near-ground wind speeds, respectively). For example, centerline concentrations of lead (Pb) in the yard could be placed between 8 and 30 μg/Nm 3 . These estimates are much higher than the Indian National Ambient Air Quality Standards (NAAQS) for Pb (0.5 μg/Nm 3 ). This research has already become the critical science and technology inputs for formulation of policies for eco-friendly dismantling of ships, formulation of ideal procedure and corresponding health, safety, and environment provisions. The insights obtained from this research are also being used in developing appropriate technologies for minimizing exposure to workers and minimizing possibilities of causing heavy metal pollution in the intertidal zone of ship recycling yards in India. -- Highlights

Spatial analysis of concentrations of multiple air pollutants using NASA DISCOVER-AQ aircraft measurements: Implications for exposure assessment.

Science.gov (United States)

Lee, Hyung Joo; Chatfield, Robert B; Bell, Michelle L

2018-01-01

In recent years, multipollutant approaches have been employed to investigate the association with health outcomes to better represent real-world conditions than more traditional analysis that considers a single pollutant. With regard to the exposure assessment of a mixture of air pollutants, it is critical to understand the spatial variability in multipollutant relations in order to assess their potential health implications. In this study, we investigated the spatial relations of multiple pollutant concentrations (i.e., NO x , NO y , black carbon, carbon monoxide, acetaldehyde, formaldehyde, toluene, xylenes/ethylbenzene, ozone, water-soluble organic carbon, and aerosol extinction) observed from the P-3B aircraft in the 2011 NASA field campaign in Baltimore/Washington D.C. areas during July 2011. The between-pollutant Pearson correlations and Z-scores (calculated from log-transformed concentrations) between near-highways and non-highways and between near-urban centers and non-urban centers varied by pollutant pair and space. We found generally lower correlations between NO x and other pollutants for near-highways (average r = 0.36) than for non-highways (average r = 0.41) and also for non-urban centers (average r = 0.37) than for near-urban centers (average r = 0.41). This indicated that the temporal associations between NO x and health outcomes might be less affected by other pollutants, which were also related to same health outcomes, for near-highways and non-urban centers. The analysis of between-pollutant Z-scores showed varying spatial relations for popular traffic-related pollutants with the Z-score differences of 0.43 (NO x -carbon monoxide), 0.29 (NO x -black carbon), and 0.17 (black carbon-carbon monoxide) between near-highways and non-highways. This result exhibited heterogeneous traffic-related pollutant mixtures with the proximity to highways, potentially leading to the diverse extent of health associations. Furthermore, a mixed effects model

Supplemental mathematical formulations, Atmospheric pathway: The Multimedia Environmental Pollutant Assessment System (MEPAS)

International Nuclear Information System (INIS)

Droppo, J.G.; Buck, J.W.

1996-03-01

The Multimedia Environmental Pollutant Assessment System (MEPAS) is an integrated software implementation of physics-based fate and transport models for health and environmental risk assessments of both radioactive and hazardous pollutants. This atmospheric component report is one of a series of formulation reports that document the MEPAS mathematical models. MEPAS is a ''multimedia'' model; pollutant transport is modeled within, through, and between multiple media (air, soil, groundwater, and surface water). The estimated concentrations in the various media are used to compute exposures and impacts to the environment, to maximum individuals, and to populations

Blood lead concentrations in wild birds from a polluted mining region at Villa de La Paz, San Luis Potosi, Mexico.

Science.gov (United States)

Chapa-Vargas, Leonardo; Mejia-Saavedra, Jose J; Monzalvo-Santos, Karina; Puebla-Olivares, Fernando

2010-01-01

This investigation was undertaken to determine the concentrations of lead in bird blood samples from a mining region in central Mexico and to compare concentrations among several different feeding guilds. The study took place in the Mexican state of San Luis Potosi in a region known as "Villa de la Paz." This is one of the most intensely exploited mining regions in central Mexico and has been actively mined for over four centuries. Lead concentrations from bird blood samples taken from four polluted sites were significantly higher than those from a control, unpolluted site (F = 6.3, P birds from a highly polluted site were higher than those from a site that has intermediate pollution levels (P birds had significantly lower lead concentrations compared to granivores, frugivores-insectivores, and omnivores (F = 4.86, P = 0.004), and a large proportion of all individuals had blood lead concentrations indicative of low, sub-lethal toxic effects. Finally, in two polluted sites, remarkably small numbers of insectivore-frugivores, and granivores were trapped, and in one polluted site a large number of insectivores was trapped (X(2) = 29.9, P = 0.03), and no differences in proportions of migrants and non-migrants were found among sampling sites (X(2) = 0.6, P = 0.96). To date, it has not been determined to what extent constant exposure to these levels of pollution can influence health at the individual level, lifespan, and, therefore, population demography of birds from this region.

The use of gamma radiation and polymeric materials in the removal of some toxic pollutants from polluted water

International Nuclear Information System (INIS)

Mohamed, M. E.M.

2002-01-01

Gamma radiation degradation of polluted water containing different anionic detergents (Texapon, Acyl Sarcoside, Diethanol Amide of Coconut Fatty Acid, Alkyl Sulfonate and Leonil UN-ET) and non-ionic detergents (Alkyl Polyglycol Ether, Hostapal SF-ET, Hostapal CV-ET and Tween-60) were studied as a function of the detergent Concentration, Ph, dose and dose rate. The synergistic effects resulting from adding different additives such as nitrogen, oxygen and hydrogen peroxide on the degradation process were investigated and showed that radiation degradation resulted in degrading the pollutants to a high extent (Between 80-95%). The ability of using Granular Activated Carbon, Agricultural By Products (Sugar Cane Bagasse and Rice Straw), Ion Exchange Resins (Merck II, III and IV) and the grafted polymeric membranes from Low Density Polyethylene were carried out. From the results, It can be concluded that, the gamma radiation coupled with adsorption was the best method for removing these pollutants and down their concentrations below the maximum permissible value according to the FAO regulations than the adsorption process alone and it was the most economic one

Mercury and gold concentrations of highly polluted environmental samples determined using prompt gamma-ray analysis and instrument neutron activation analysis

Science.gov (United States)

Osawa, Takahito; Hatsukawa, Yuichi; Appel, Peter W. U.; Matsue, Hideaki

2011-04-01

The authors have established a method of determining mercury and gold in severely polluted environmental samples using prompt gamma-ray analysis (PGA) and instrumental neutron activation analysis (INAA). Since large amounts of mercury are constantly being released into the environment by small-scale gold mining in many developing countries, the mercury concentration in tailings and water has to be determined to mitigate environmental pollution. Cold-vapor atomic absorption analysis, the most pervasive method of mercury analysis, is not suitable because tailings and water around mining facilities have extremely high mercury concentrations. On the other hand, PGA can determine high mercury concentrations in polluted samples as it has an appropriate level of sensitivity. Moreover, gold concentrations can be determined sequentially by using INAA after PGA. In conclusion, the analytical procedure established in this work using PGA and INAA is the best way to evaluate the degree of pollution and the tailing resource value. This method will significantly contribute to mitigating problems in the global environment.

Mercury and gold concentrations of highly polluted environmental samples determined using prompt gamma-ray analysis and instrument neutron activation analysis

International Nuclear Information System (INIS)

Osawa, Takahito; Hatsukawa, Yuichi; Appel, Peter W.U.; Matsue, Hideaki

2011-01-01

The authors have established a method of determining mercury and gold in severely polluted environmental samples using prompt gamma-ray analysis (PGA) and instrumental neutron activation analysis (INAA). Since large amounts of mercury are constantly being released into the environment by small-scale gold mining in many developing countries, the mercury concentration in tailings and water has to be determined to mitigate environmental pollution. Cold-vapor atomic absorption analysis, the most pervasive method of mercury analysis, is not suitable because tailings and water around mining facilities have extremely high mercury concentrations. On the other hand, PGA can determine high mercury concentrations in polluted samples as it has an appropriate level of sensitivity. Moreover, gold concentrations can be determined sequentially by using INAA after PGA. In conclusion, the analytical procedure established in this work using PGA and INAA is the best way to evaluate the degree of pollution and the tailing resource value. This method will significantly contribute to mitigating problems in the global environment.

Metal pollution (Cd, Pb, Zn, and As) in agricultural soils and soybean, Glycine max, in southern China.

Science.gov (United States)

Zhao, Yunyun; Fang, Xiaolong; Mu, Yinghui; Cheng, Yanbo; Ma, Qibin; Nian, Hai; Yang, Cunyi

2014-04-01

Crops produced on metal-polluted agricultural soils may lead to chronic toxicity to humans via the food chain. To assess metal pollution in agricultural soils and soybean in southern China, 30 soybean grain samples and 17 soybean-field soil samples were collected from 17 sites in southern China, and metal concentrations of samples were analyzed by graphite furnace atomic absorption spectrophotometer. The integrated pollution index was used to evaluate if the samples were contaminated by Cd, Pb, Zn and As. Results showed that Cd concentration of 12 samples, Pb concentration of 2 samples, Zn concentration of 2 samples, and As concentrations of 2 samples were above the maximum permissible levels in soils. The integrated pollution index indicated that 11 of 17 soil samples were polluted by metals. Metal concentrations in soybean grain samples ranged from 0.11 to 0.91 mg kg(-1) for Cd; 0.34 to 2.83 mg kg(-1) for Pb; 42 to 88 mg kg(-1) for Zn; and 0.26 to 5.07 mg kg(-1) for As, which means all 30 soybean grain samples were polluted by Pb, Pb/Cd, Cd/Pb/As or Pb/As. Taken together, our study provides evidence that metal pollution is an important concern in agricultural soils and soybeans in southern China.

The Empirical Relationship between Mining Industry Development and Environmental Pollution in China

OpenAIRE

Li, Gerui; Lei, Yalin; Ge, Jianping; Wu, Sanmang

2017-01-01

This study uses a vector autoregression (VAR) model to analyze changes in pollutants among different mining industries and related policy in China from 2001 to 2014. The results show that: (1) because the pertinence of standards for mining waste water and waste gas emissions are not strong and because the maximum permissible discharge pollutant concentrations in these standards are too high, ammonia nitrogen and industrial sulfur dioxide discharges increased in most mining industries; (2) che...

Quantile-based Bayesian maximum entropy approach for spatiotemporal modeling of ambient air quality levels.

Science.gov (United States)

Yu, Hwa-Lung; Wang, Chih-Hsin

2013-02-05

Understanding the daily changes in ambient air quality concentrations is important to the assessing human exposure and environmental health. However, the fine temporal scales (e.g., hourly) involved in this assessment often lead to high variability in air quality concentrations. This is because of the complex short-term physical and chemical mechanisms among the pollutants. Consequently, high heterogeneity is usually present in not only the averaged pollution levels, but also the intraday variance levels of the daily observations of ambient concentration across space and time. This characteristic decreases the estimation performance of common techniques. This study proposes a novel quantile-based Bayesian maximum entropy (QBME) method to account for the nonstationary and nonhomogeneous characteristics of ambient air pollution dynamics. The QBME method characterizes the spatiotemporal dependence among the ambient air quality levels based on their location-specific quantiles and accounts for spatiotemporal variations using a local weighted smoothing technique. The epistemic framework of the QBME method can allow researchers to further consider the uncertainty of space-time observations. This study presents the spatiotemporal modeling of daily CO and PM10 concentrations across Taiwan from 1998 to 2009 using the QBME method. Results show that the QBME method can effectively improve estimation accuracy in terms of lower mean absolute errors and standard deviations over space and time, especially for pollutants with strong nonhomogeneous variances across space. In addition, the epistemic framework can allow researchers to assimilate the site-specific secondary information where the observations are absent because of the common preferential sampling issues of environmental data. The proposed QBME method provides a practical and powerful framework for the spatiotemporal modeling of ambient pollutants.

Simulating urban-scale air pollutants and their predicting capabilities over the Seoul metropolitan area.

Science.gov (United States)

Park, Il-Soo; Lee, Suk-Jo; Kim, Cheol-Hee; Yoo, Chul; Lee, Yong-Hee

2004-06-01

Urban-scale air pollutants for sulfur dioxide, nitrogen dioxide, particulate matter with aerodynamic diameter > or = 10 microm, and ozone (O3) were simulated over the Seoul metropolitan area, Korea, during the period of July 2-11, 2002, and their predicting capabilities were discussed. The Air Pollution Model (TAPM) and the highly disaggregated anthropogenic and the biogenic gridded emissions (1 km x 1 km) recently prepared by the Korean Ministry of Environment were applied. Wind fields with observational nudging in the prognostic meteorological model TAPM are optionally adopted to comparatively examine the meteorological impact on the prediction capabilities of urban-scale air pollutants. The result shows that the simulated concentrations of secondary air pollutant largely agree with observed levels with an index of agreement (IOA) of >0.6, whereas IOAs of approximately 0.4 are found for most primary pollutants in the major cities, reflecting the quality of emission data in the urban area. The observationally nudged wind fields with higher IOAs have little effect on the prediction for both primary and secondary air pollutants, implying that the detailed wind field does not consistently improve the urban air pollution model performance if emissions are not well specified. However, the robust highest concentrations are better described toward observations by imposing observational nudging, suggesting the importance of wind fields for the predictions of extreme concentrations such as robust highest concentrations, maximum levels, and >90th percentiles of concentrations for both primary and secondary urban-scale air pollutants.

The Impact of Future Emissions Changes on Air Pollution Concentrations and Related Human Health Effects

Science.gov (United States)

Mikolajczyk, U.; Suppan, P.; Williams, M.

2015-12-01

Quantification of potential health benefits of reductions in air pollution on the local scale is becoming increasingly important. The aim of this study is to conduct health impact assessment (HIA) by utilizing regionally and spatially specific data in order to assess the influence of future emission scenarios on human health. In the first stage of this investigation, a modeling study was carried out using the Weather Research and Forecasting (WRF) model coupled with Chemistry to estimate ambient concentrations of air pollutants for the baseline year 2009, and for the future emission scenarios in southern Germany. Anthropogenic emissions for the baseline year 2009 are derived from the emission inventory provided by the Netherlands Organization of Applied Scientific Research (TNO) (Denier van der Gon et al., 2010). For Germany, the TNO emissions were replaced by gridded emission data with a high spatial resolution of 1/64 x 1/64 degrees. Future air quality simulations are carried out under different emission scenarios, which reflect possible energy and climate measures in year 2030. The model set-up included a nesting approach, where three domains with horizontal resolution of 18 km, 6 km and 2 km were defined. The simulation results for the baseline year 2009 are used to quantify present-day health burdens. Concentration-response functions (CRFs) for PM2.5 and NO2 from the WHO Health risks of air Pollution in Europe (HRAPIE) project were applied to population-weighted mean concentrations to estimate relative risks and hence to determine numbers of attributable deaths and associated life-years lost. In the next step, future health impacts of projected concentrations were calculated taking into account different emissions scenarios. The health benefits that we assume with air pollution reductions can be used to provide options for future policy decisions to protect public health.

Atmospheric Concentrations of Persistent Organic Pollutants in the Southern Ocean

Science.gov (United States)

Vlahos, P.; Edson, J.; Cifuentes, A.; McGillis, W. R.; Zappa, C.

2008-12-01

Long-range transport of persistent organic pollutant (POPs) is a global concern. Remote regions such as the Southern Ocean are greatly under-sampled though critical components in understanding POPs cycling. Over 20 high-volume air samples were collected in the Southern Ocean aboard the RV Brown during the GASEX III experiment between Mar 05 to April 9 2008. The relatively stationary platform (51S,38W) enabled the collection of a unique atmospheric time series at this open ocean station. Air sampling was also conducted across transects from Punto Arenas, Chile and to Montevideo, Uruguay. Samples were collected using glass sleeves packed with poly-urethane foam plugs and C-18 resin in order to collect target organic pollutants (per-fluorinated compounds, currently and historically used pesticides) in this under-sampled region. Here we present POPs concentrations and trends over the sampled period and compare variations with air parcel back trajectories to establish potential origins of their long-range transport.

[Observation on atmospheric pollution in Xianghe during Beijing 2008 Olympic Games].

Science.gov (United States)

Pan, Yue-Peng; Wang, Yue-Si; Hu, Bo; Liu, Quan; Wang, Ying-Hong; Nan, Wei-Dong

2010-01-01

There is a concern that much of the atmospheric pollution experienced in Beijing is regional in nature and not attributable to local sources. The objective of this study is to examine the contribution of sources outside Beijing to atmospheric pollution levels during Beijing 2008 Olympic Games. The observations of SO2, NO(x), O3, PM2.5 and PM10 were conducted from June 1 to September 30, 2008 in Xianghe, a rural site about 70 km southeast of Beijing. Sources and transportation of atmospheric pollution during the experiment were discussed with surface meteorology data and backward trajectories calculated using HYSPLIT model. The results showed that the daily average maximum (mean +/- standard deviation) concentrations of SO2, NO(x), O3, PM2.5, and PM10 during observation reached 84.4(13.4 +/- 15.2), 43.3 (15.9 +/- 9.1), 230 (82 +/- 38), 184 (76 +/- 42) and 248 (113 +/- 52) microg x m(-3), respectively. In particular, during the pollution episodes from July 20 to August 12, the hourly average concentration of O3 exceeded the National Ambient Air Quality Standard II for 46 h (9%), and the daily average concentration of PM10 exceeded the Standard for 11 d (46%); PM2.5 exceeded the US EPA Standard for 18 d (75%). The daily average concentrations of SO2, NO(x), O3, PM2.5 and PM10 decreased from 27.7, 18.6, 96, 90, 127 microg x m(-3) in June-July to 5.8, 13.2, 80, 60, 106 microg x m(-3) during Olympic Games (August-September), respectively. The typical diurnal variations of NO(x), PM2.5 and PM10 were similar, peaking at 07:00 and 20:00, while the maximum of O3 occurred between 14:00 to 16:00 local time. The findings also suggested that the atmospheric pollution in Xianghe is related to local emission, regional transport as well as the meteorological conditions. Northerly wind and precipitation are favorable for diffusion and wet deposition of pollutants, while sustained south flows make the atmospheric pollution more serious. The lead-lag correlation analysis during the

Trace Element Concentrations in Tree Leaves and Lichen Collected Along a Metal Pollution Gradient Near Olkusz (Southern Poland).

Science.gov (United States)

Zakrzewska, Marta; Klimek, Beata

2018-02-01

The aim of the study was to assess the metal pollution in the vicinity of the Bukowno smelter near Olkusz in southern Poland. Birch and oak leaves, pine needles and a lichen Hypogymnia physodes, overgrowing pine bark were collected at stands at different distances from the smelter and analysed for cadmium (Cd), copper (Cu), lead (Pb) and zinc (Zn) content. Concentrations of metals in the lichen were usually higher than in the tree leaves/needles and decreased with distance from the smelter, apart from the Cu content. The strongest correlation was noticed between Cd and Pb concentrations, which indicates a common pollution source (the smelter). Our results show that birch leaves can be potentially useful as a bioindicator of Zn air pollution since this species was shown to accumulate high amounts of zinc, related to environmental pollution with that metal, in their leaves.

Using a chemistry transport model to account for the spatial variability of exposure concentrations in epidemiologic air pollution studies.

Science.gov (United States)

Valari, Myrto; Menut, Laurent; Chatignoux, Edouard

2011-02-01

Environmental epidemiology and more specifically time-series analysis have traditionally used area-averaged pollutant concentrations measured at central monitors as exposure surrogates to associate health outcomes with air pollution. However, spatial aggregation has been shown to contribute to the overall bias in the estimation of the exposure-response functions. This paper presents the benefit of adding features of the spatial variability of exposure by using concentration fields modeled with a chemistry transport model instead of monitor data and accounting for human activity patterns. On the basis of county-level census data for the city of Paris, France, and a Monte Carlo simulation, a simple activity model was developed accounting for the temporal variability between working and evening hours as well as during transit. By combining activity data with modeled concentrations, the downtown, suburban, and rural spatial patterns in exposure to nitrogen dioxide, ozone, and PM2.5 (particulate matter [PM] pollution on total nonaccidental mortality for the 4-yr period from 2001 to 2004. It was shown that the time series of the exposure surrogates developed here are less correlated across co-pollutants than in the case of the area-averaged monitor data. This led to less biased exposure-response functions when all three co-pollutants were inserted simultaneously in the same regression model. This finding yields insight into pollutant-specific health effects that are otherwise masked by the high correlation among co-pollutants.

The impact of land use on microbial surface water pollution.

Science.gov (United States)

Schreiber, Christiane; Rechenburg, Andrea; Rind, Esther; Kistemann, Thomas

2015-03-01

Our knowledge relating to water contamination from point and diffuse sources has increased in recent years and there have been many studies undertaken focusing on effluent from sewage plants or combined sewer overflows. However, there is still only a limited amount of microbial data on non-point sources leading to diffuse pollution of surface waters. In this study, the concentrations of several indicator micro-organisms and pathogens in the upper reaches of a river system were examined over a period of 16 months. In addition to bacteria, diffuse pollution caused by Giardia lamblia and Cryptosporidium spp. was analysed. A single land use type predestined to cause high concentrations of all microbial parameters could not be identified. The influence of different land use types varies between microbial species. The microbial concentration in river water cannot be explained by stable non-point effluent concentrations from different land use types. There is variation in the ranking of the potential of different land use types resulting in surface water contamination with regard to minimum, median and maximum effects. These differences between median and maximum impact indicate that small-scale events like spreading manure substantially influence the general contamination potential of a land use type and may cause increasing micro-organism concentrations in the river water by mobilisation during the next rainfall event. Copyright © 2014 Elsevier GmbH. All rights reserved.

Air Pollution Modelling to Predict Maximum Ground Level Concentration for Dust from a Palm Oil Mill Stack

Directory of Open Access Journals (Sweden)

Regina A. A.

2010-12-01

Full Text Available The study is to model emission from a stack to estimate ground level concentration from a palm oil mill. The case study is a mill located in Kuala Langat, Selangor. Emission source is from boilers stacks. The exercise determines the estimate the ground level concentrations for dust to the surrounding areas through the utilization of modelling software. The surround area is relatively flat, an industrial area surrounded by factories and with palm oil plantations in the outskirts. The model utilized in the study was to gauge the worst-case scenario. Ambient air concentrations were garnered calculate the increase to localized conditions. Keywords: emission, modelling, palm oil mill, particulate, POME

Soil and Water Assessment Tool model predictions of annual maximum pesticide concentrations in high vulnerability watersheds.

Science.gov (United States)

Winchell, Michael F; Peranginangin, Natalia; Srinivasan, Raghavan; Chen, Wenlin

2018-05-01

Recent national regulatory assessments of potential pesticide exposure of threatened and endangered species in aquatic habitats have led to increased need for watershed-scale predictions of pesticide concentrations in flowing water bodies. This study was conducted to assess the ability of the uncalibrated Soil and Water Assessment Tool (SWAT) to predict annual maximum pesticide concentrations in the flowing water bodies of highly vulnerable small- to medium-sized watersheds. The SWAT was applied to 27 watersheds, largely within the midwest corn belt of the United States, ranging from 20 to 386 km 2 , and evaluated using consistent input data sets and an uncalibrated parameterization approach. The watersheds were selected from the Atrazine Ecological Exposure Monitoring Program and the Heidelberg Tributary Loading Program, both of which contain high temporal resolution atrazine sampling data from watersheds with exceptionally high vulnerability to atrazine exposure. The model performance was assessed based upon predictions of annual maximum atrazine concentrations in 1-d and 60-d durations, predictions critical in pesticide-threatened and endangered species risk assessments when evaluating potential acute and chronic exposure to aquatic organisms. The simulation results showed that for nearly half of the watersheds simulated, the uncalibrated SWAT model was able to predict annual maximum pesticide concentrations within a narrow range of uncertainty resulting from atrazine application timing patterns. An uncalibrated model's predictive performance is essential for the assessment of pesticide exposure in flowing water bodies, the majority of which have insufficient monitoring data for direct calibration, even in data-rich countries. In situations in which SWAT over- or underpredicted the annual maximum concentrations, the magnitude of the over- or underprediction was commonly less than a factor of 2, indicating that the model and uncalibrated parameterization

Determination of trace element concentrations and stable lead, uranium and thorium isotope ratios by quadrupole-ICP-MS in NORM and NORM-polluted sample leachates

Energy Technology Data Exchange (ETDEWEB)

Mas, J.L., E-mail: ppmasb@us.es [Dpto. Fisica Aplicada I, EPS, Universidad de Sevilla, 41012 Sevilla (Spain); Villa, M. [Servicio de Radioisotopos, Centro de Investigacion, Tecnologia e Innovacion (CITIUS), Universidad de Sevilla, Avda. Reina Mercedes 4b, 41012 Sevilla (Spain); Dpto. Fisica Aplicada II, ETS de Arquitectura, Universidad de Sevilla, Avda. Reina Mercedes 2, 41012 Sevilla (Spain); Hurtado, S. [Servicio de Radioisotopos, Centro de Investigacion, Tecnologia e Innovacion (CITIUS), Universidad de Sevilla, Avda. Reina Mercedes 4b, 41012 Sevilla (Spain); Garcia-Tenorio, R. [Dpto. Fisica Aplicada II, ETS de Arquitectura, Universidad de Sevilla, Avda. Reina Mercedes 2, 41012 Sevilla (Spain)

2012-02-29

Highlights: Black-Right-Pointing-Pointer Polluted sediment and NORM samples. Black-Right-Pointing-Pointer An efficient yet fast process allowing multi-parametric determinations in <3 days. Black-Right-Pointing-Pointer Trace element concentrations, Pb, Th and U isotope ratios with a single instrument. - Abstract: This work focuses on the monitoring of the potential pollution in scenarios that involve NORM-related industrial activities (environmental or in-door scenarios). The objective was to develop a method to determine extent and origin of the contamination, suitable for monitoring (i.e. simple, fast and economical) and avoiding the use of too many different instruments. It is presented a radiochemical method that allows the determination of trace element concentrations and {sup 206}Pb/{sup 207}Pb/{sup 208}Pb, {sup 238}U/{sup 234}U and {sup 232}Th/{sup 230}Th isotope ratios using a single sample aliquot and a single instrument (ICP-QMS). Eichrom UTEVA{sup Registered-Sign} extraction chromatography minicolumns were used to separate uranium and thorium in sample leachates. Independent ICP-MS determinations of uranium and thorium isotope ratios were carried out afterwards. Previously a small aliquot of the leachate was used for the determination of trace element concentrations and lead isotope ratios. Several radiochemical arrangements were tested to get maximum performances and simplicity of the method. The performances of the method were studied in terms of chemical yields of uranium and thorium and removal of the potentially interfering elements. The established method was applied to samples from a chemical industry and sediments collected in a NORM-polluted scenario. The results obtained from our method allowed us to infer not only the extent, but also the sources of the contamination in the area.

A novel approach to estimating potential maximum heavy metal exposure to ship recycling yard workers in Alang, India

Energy Technology Data Exchange (ETDEWEB)

Deshpande, Paritosh C.; Tilwankar, Atit K.; Asolekar, Shyam R., E-mail: asolekar@iitb.ac.in

2012-11-01

The 180 ship recycling yards located on Alang-Sosiya beach in the State of Gujarat on the west coast of India is the world's largest cluster engaged in dismantling. Yearly 350 ships have been dismantled (avg. 10,000 ton steel/ship) with the involvement of about 60,000 workers. Cutting and scrapping of plates or scraping of painted metal surfaces happens to be the commonly performed operation during ship breaking. The pollutants released from a typical plate-cutting operation can potentially either affect workers directly by contaminating the breathing zone (air pollution) or can potentially add pollution load into the intertidal zone and contaminate sediments when pollutants get emitted in the secondary working zone and gets subjected to tidal forces. There was a two-pronged purpose behind the mathematical modeling exercise performed in this study. First, to estimate the zone of influence up to which the effect of plume would extend. Second, to estimate the cumulative maximum concentration of heavy metals that can potentially occur in ambient atmosphere of a given yard. The cumulative maximum heavy metal concentration was predicted by the model to be between 113 {mu}g/Nm{sup 3} and 428 {mu}g/Nm{sup 3} (at 4 m/s and 1 m/s near-ground wind speeds, respectively). For example, centerline concentrations of lead (Pb) in the yard could be placed between 8 and 30 {mu}g/Nm{sup 3}. These estimates are much higher than the Indian National Ambient Air Quality Standards (NAAQS) for Pb (0.5 {mu}g/Nm{sup 3}). This research has already become the critical science and technology inputs for formulation of policies for eco-friendly dismantling of ships, formulation of ideal procedure and corresponding health, safety, and environment provisions. The insights obtained from this research are also being used in developing appropriate technologies for minimizing exposure to workers and minimizing possibilities of causing heavy metal pollution in the intertidal zone of ship recycling

Black carbon concentrations in the highly polluted Kathmandu Valley, Nepal: a three year monitoring with a dual-spot Aethalometer

Science.gov (United States)

Rupakheti, Maheswar; Drinovec, Luka; Puppala, SivaPraveen; Mahata, Khadak; Rupakheti, Dipesh; Kathayat, Bhogendra; Singdan, Pratik; Panday, Arnico; Lawrence, Mark

2016-04-01

Our knowledge about ambient black carbon (BC) in the vast Himalayan region, a region vulnerable to impacts of global warming, is very limited due to unavailability of a long-term ambient monitoring. Here we present results from a continuous monitoring of ambient BC concentrations, with a new generation Aethalometer (AE33), over a three year period (January 2013- January 2016) at a semi-urban site in the highly polluted Kathmandu Valley in the foothills of the central Himalaya, one of the most polluted cities in the world. This is the longest time series of BC concentrations that have been monitored with AE33 (which uses the dual-spot technique for a real-time filter loading compensation) in highly polluted ambient environment. The measurements were carried out under the framework of project SusKat (Sustainable Atmosphere for the Kathmandu Valley). BC concentrations were found to be extremely high, especially in winter and the pre-monsoon period, with the hourly-averaged values often exceeding 50 μg/m3. BC concentrations showed a clear diurnal cycle with a prominent peak around 8-9 am and a second peak around 8-9 pm local time in all four seasons. Night-time BC was also fairly high. The diurnal cycle was driven by a combination of increased emissions from traffic, cooking activities, garbage burning, and lower mixing heights (˜200 m) and reduced horizontal ventilation in the mornings and evenings. BC concentrations showed significant seasonal variations - a maximum in winter season and minimum during the monsoon (rainy) season, with monthly average values in the range 5-30 μg/m3. An increase in emissions from the operation of over 100 brick kilns in winter and spring, and an increase in the use of small but numerous diesel power generators during hours with power cuts contributed significantly to ambient BC concentrations in the valley. Fractional contributions of biomass burning and fossil fuel combustion to BC was estimated based on a real-time method for

Comparing wastewater chemicals, indicator bacteria concentrations, and bacterial pathogen genes as fecal pollution indicators

Science.gov (United States)

Haack, S.K.; Duris, J.W.; Fogarty, L.R.; Kolpin, D.W.; Focazio, M.J.; Furlong, E.T.; Meyer, M.T.

2009-01-01

The objective of this study was to compare fecal indicator bacteria (FIB) (fecal coliforms, Escherichia coli [EC], and enterococci [ENT]) concentrations with a wide array of typical organic wastewater chemicals and selected bacterial genes as indicators of fecal pollution in water samples collected at or near 18 surface water drinking water intakes. Genes tested included esp (indicating human-pathogenic ENT) and nine genes associated with various animal sources of shiga-toxin-producing EC (STEC). Fecal pollution was indicated by genes and/or chemicals for 14 of the 18 tested samples, with little relation to FIB standards. Of 13 samples with animal sources of STEC) were detected in eight. Only the EC eaeA gene was positively correlated with FIB concentrations. Human-source fecal pollution was indicated by the esp gene and the human pharmaceutical carbamazepine in one of the nine samples that met all FIB recreational water quality standards. Escherichia coli rfbO157 and stx2c genes, which are typically associated with cattle sources and are of potential human health significance, were detected in one sample in the absence of tested chemicals. Chemical and gene-based indicators of fecal contamination may be present even when FIB standards are met, and some may, unlike FIB, indicate potential sources. Application of multiple water quality indicators with variable environmental persistence and fate may yield greater confidence in fecal pollution assessment and may inform remediation decisions. Copyright ?? 2009 by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America. All rights reserved.

PHOTOCHEMICAL AIR POLLUTION IN THE NORTH OF PORTUGAL: A HIGH TROPOSHERIC OZONE EPISODE

Science.gov (United States)

Monteiro, A.; Carvalho, A.; Tchepel, O.; Ferreira, J.; Martins, H.; Miranda, A.; Borrego, C.; Saavedra, S.; Rodríguez, A.; Souto, J. A.

2009-12-01

Very high concentrations of ozone are continuously measured at the monitoring station at Lamas d’Olo, located at the North of Portugal,. A particular high photochemical episode occurred between 11 and 13 of July 2005, registering ozone hourly maximum values above 350 µg.m-3. This ozone-rich episode is investigated in this paper, in order to identify its origin and formation. Besides the analysis of both meteorological and air quality monitoring datasets, a numerical modelling approach, based on MM5-CAMx system, was used to simulate the dispersion and transport (horizontal and vertical) of the photochemical pollutants and its precursors. A cross spectrum analysis of the meteorological and air quality time series was performed, in the frequency domain, to establish the relationships between ozone data measured at Lamas d’Olo with air quality data from neighbourhood stations and meteorological parameters. Results point out different behaviour/contribution between the analysed sites. Moreover, different contributions of the u and v wind component on the ozone concentration fluctuations were found suggesting the presence a mountain breeze circulation and a north synoptic transport. The preliminary modelling results pointed out that the vertical transport of pollutants are responsible for the measured high concentrations, combined with particular meteorological conditions, related to the planetary boundary layer (PBL) development. The pollutants transported and existent at high vertical levels are captured/trapped when the PBL height reaches its daily maximum, and extremely high ozone ground level concentrations are consequently measured.

Organic and Inorganic Pollutant Concentrations Suggest Anthropogenic Contamination of Soils Along the Manali-Leh Highway, Northwestern Himalaya, India.

Science.gov (United States)

Dasgupta, Rajarshi; Crowley, Brooke E; Barry Maynard, J

2017-05-01

Most studies on roadside soil pollution have been performed in areas where petrol is the main fuel. Very little work has been conducted in regions where diesel predominates. We collected soil samples from four sites that span a precipitation gradient along the Manali-Leh Highway in northwestern Himalaya, India. This road traverses rough terrain and most of the vehicles that travel along it are diesel-driven. At each site, we collected samples at incremental distances from the highway (0, 2, 5, 10, 20, and 150 m), and at each distance we collected samples from three depths (3, 9, and 15 cm). We assessed the concentrations of 10 heavy metals (Al, Fe, Cr, Cu, Pb, Ni, Co, Zn, V, and Ba), total sulphur, and total organic carbon (TOC) at each distance, and we measured the concentration of 16 polycyclic aromatic hydrocarbons (PAHs) at 2 m from the highway. Overall, we found that metal concentrations are low and there is no relationship between concentrations and distance from the highway, or depth within the soil profile. Sulphur concentrations, on the other hand, are high in roadside soils and there is a negative relationship between concentration and distance from the highway. PAH concentrations are low, but the proportion of different ringed species suggests that their source is anthropogenic. Correlations between TOC and the various pollutants further suggest that diesel vehicles and potentially biomass combustion are starting to affect the roadside environment in remote northwestern India. We suggest that pollutant concentrations be regularly monitored.

Estimation of flashover voltage probability of overhead line insulators under industrial pollution, based on maximum likelihood method

International Nuclear Information System (INIS)

Arab, M.N.; Ayaz, M.

2004-01-01

The performance of transmission line insulator is greatly affected by dust, fumes from industrial areas and saline deposit near the coast. Such pollutants in the presence of moisture form a coating on the surface of the insulator, which in turn allows the passage of leakage current. This leakage builds up to a point where flashover develops. The flashover is often followed by permanent failure of insulation resulting in prolong outages. With the increase in system voltage owing to the greater demand of electrical energy over the past few decades, the importance of flashover due to pollution has received special attention. The objective of the present work was to study the performance of overhead line insulators in the presence of contaminants such as induced salts. A detailed review of the literature and the mechanisms of insulator flashover due to the pollution are presented. Experimental investigations on the behavior of overhead line insulators under industrial salt contamination are carried out. A special fog chamber was designed in which the contamination testing of insulators was carried out. Flashover behavior under various degrees of contamination of insulators with the most common industrial fume components such as Nitrate and Sulphate compounds was studied. Substituting the normal distribution parameter in the probability distribution function based on maximum likelihood develops a statistical method. The method gives a high accuracy in the estimation of the 50% flashover voltage, which is then used to evaluate the critical flashover index at various contamination levels. The critical flashover index is a valuable parameter in insulation design for numerous applications. (author)

A physical explanation of the lognormality of pollutant concentrations

International Nuclear Information System (INIS)

Ott, W.R.

1990-01-01

Investigators in different environmental fields have reported that the concentrations of various measured substances have frequency distributions that are lognormal, or nearly so. That is, when the logarithms of the observed concentrations are plotted as a frequency distribution, the resulting distribution is approximately normal, or Gaussian, over much of the observed range. Examples include radionuclides in soil, pollutants in ambient air, indoor air quality, trace metals in streams, metals in biological tissue, calcium in human remains. The ubiquity of the lognormal distribution in environmental processes is surprising and has not been adequately explained, since common processes in nature (for example, computation of the mean and the analysis of error) usually give rise to distributions that are normal rather than lognormal. This paper takes the first step toward explaining why lognormal distributions can arise naturally from certain physical processes that are analogous to those found in the environment. In this paper, these processes are treated mathematically, and the results are illustrated in a laboratory beaker experiment that is simulated on the computer

Atmospheric Metal Pollutants-Archives, Methods, and History

International Nuclear Information System (INIS)

Norton, Stephen A.

2007-01-01

Pollution of the atmosphere with cadmium (Cd), mercury (Hg), and lead (Pb) is a consequence of human activities. Natural archives are necessary to reconstruct the long-term history of metal deposition because accurate measurement of atmospheric deposition is a recent accomplishment. Reconstructions require: (1) accurate determination of concentrations of elements and isotopes, (2) accurate chronology of archives, and (3) archives that faithfully record atmosphere deposition. The most useful long-term archives are accumulations of ice and snow, peat, and lake sediment. Quantification of Cd deposition is uncommon because of its low concentration and substantial chemical mobility. Nonetheless, trends in peat and lake sediment are similar to those of Hg and Pb since ca. 1800 a.d. Both Hg and Pb are relatively chemically immobile and thus the peat and lake archives are believed to record historic trends of atmospheric deposition. Isotopic and concentration studies of Pb indicate a history of northern hemisphere atmospheric pollution extending back prior to 0 a.d. Although measurements of Hg concentration are now routine, isotopic measurements are in their infancy. Some Hg pollution sources have unique isotopic ratios, thereby contributing unique signals to the total Hg. Maximum accumulation rates of Hg and Pb occur up to 10 years later than for Cd (1970s versus 1960s in eastern North America, perhaps slightly later in Europe). By 2004, deposition of Cd, Hg, and Pb had declined from peak values in eastern North America more than 75, 75, and 90%, respectively

Foehn-induced effects on local dust pollution, frontal clouds and solar radiation in the Dead Sea valley

Science.gov (United States)

Kishcha, Pavel; Starobinets, Boris; Savir, Amit; Alpert, Pinhas; Kaplan, Michael

2018-06-01

Despite the long history of investigation of foehn phenomena, there are few studies of the influence of foehn winds on air pollution and none in the Dead Sea valley. For the first time the foehn phenomenon and its effects on local dust pollution, frontal cloudiness and surface solar radiation were analyzed in the Dead Sea valley, as it occurred on 22 March 2013. This was carried out using both numerical simulations and observations. The foehn winds intensified local dust emissions, while the foehn-induced temperature inversion trapped dust particles beneath this inversion. These two factors caused extreme surface dust concentration in the western Dead Sea valley. The dust pollution was transported by west winds eastward, to the central Dead Sea valley, where the speed of these winds sharply decreased. The transported dust was captured by the ascending airflow contributing to the maximum aerosol optical depth (AOD) over the central Dead Sea valley. On the day under study, the maximum surface dust concentration did not coincide with the maximum AOD: this being one of the specific effects of the foehn phenomenon on dust pollution in the Dead Sea valley. Radar data showed a passage of frontal cloudiness through the area of the Dead Sea valley leading to a sharp drop in noon solar radiation. The descending airflow over the downwind side of the Judean Mountains led to the formation of a cloud-free band followed by only the partial recovery of solar radiation because of the extreme dust pollution caused by foehn winds.

Modification of the effect of ambient air pollution on pediatric asthma emergency visits: susceptible subpopulations

Science.gov (United States)

Strickland, Matthew J; Klein, Mitchel; Flanders, W Dana; Chang, Howard H; Mulholland, James A; Tolbert, Paige E; Darrow, Lyndsey A

2016-01-01

Background Children may have differing susceptibility to ambient air pollution concentrations depending on various background characteristics of the children. Methods Using emergency department (ED) data linked with birth records from Atlanta, Georgia, we identified ED visits for asthma or wheeze among children aged 2–16 years from 1 January 2002 through 30 June 2010 (n=109,758). We stratified by preterm delivery, term low birth weight, maternal race, Medicaid status, maternal education, maternal smoking, delivery method, and history of a bronchiolitis ED visit. Population-weighted daily average concentrations were calculated for 1-hour maximum carbon monoxide and nitrogen dioxide; 8-hour maximum ozone; and 24-hour average particulate matter less than 10 microns in diameter, particulate matter less than 2.5 microns in diameter (PM2.5), and the PM2.5 components sulfate, nitrate, ammonium, elemental carbon, and organic carbon, using measurements from stationary monitors. Poisson time-series models were used to estimate rate ratios for associations between three-day moving average pollutant concentrations and daily ED visit counts and to investigate effect-measure modification by the stratification factors. Results Associations between pollutant concentrations and asthma exacerbations were larger among children born preterm and among children born to African American mothers. Stratification by race and preterm status together suggested that both factors affected susceptibility. The largest estimated effect size (for an interquartile-range increase in pollution) was observed for ozone among preterm births to African American mothers: rate ratio=1.138 (95% confidence interval=1.077–1.203). In contrast, the rate ration for the ozone association among full-term births to mothers of other races was 1.025 (0.970–1.083). Conclusions Results support the hypothesis that children vary in their susceptibility to ambient air pollutants. PMID:25192402

Characterization of air pollutant concentrations, fleet emission factors, and dispersion near a North Carolina interstate freeway across two seasons

Science.gov (United States)

Saha, Provat K.; Khlystov, Andrey; Snyder, Michelle G.; Grieshop, Andrew P.

2018-03-01

We present field measurement data and modeling of multiple traffic-related air pollutants during two seasons at a site adjoining Interstate 40, near Durham, North Carolina. We analyze spatial-temporal and seasonal trends and fleet-average pollutant emission factors and use our data to evaluate a line source dispersion model. Month-long measurement campaigns were performed in summer 2015 and winter 2016. Data were collected at a fixed near-road site located within 10 m from the highway edge, an upwind background site and, under favorable meteorological conditions, along downwind perpendicular transects. Measurements included the size distribution, chemical composition, and volatility of submicron particles, black carbon (BC), nitrogen oxides (NOx), meteorological conditions and traffic activity data. Results show strong seasonal and diurnal differences in spatial distribution of traffic sourced pollutants. A strong signature of vehicle emissions was observed within 100-150 m from the highway edge with significantly higher concentrations during morning. Substantially higher concentrations and less-sharp near-road gradients were observed in winter for many species. Season-specific fleet-average fuel-based emission factors for NO, NOx, BC, and particle number (PN) were derived based on up- and down-wind roadside measurements. The campaign-average NOx and PN emission factors were 20% and 300% higher in winter than summer, respectively. These results suggest that the combined effect of higher emissions and their slower downwind dispersion in winter dictate the observed higher downwind concentrations and wider highway influence zone in winter for several species. Finally, measurements of traffic data, emission factors, and pollutant concentrations were integrated to evaluate a line source dispersion model (R-LINE). The dispersion model captured the general trends in the spatial and temporal patterns in near-road concentrations. However, there was a tendency for the model

Reliability Analyses of Groundwater Pollutant Transport

Energy Technology Data Exchange (ETDEWEB)

Dimakis, Panagiotis

1997-12-31

This thesis develops a probabilistic finite element model for the analysis of groundwater pollution problems. Two computer codes were developed, (1) one using finite element technique to solve the two-dimensional steady state equations of groundwater flow and pollution transport, and (2) a first order reliability method code that can do a probabilistic analysis of any given analytical or numerical equation. The two codes were connected into one model, PAGAP (Probability Analysis of Groundwater And Pollution). PAGAP can be used to obtain (1) the probability that the concentration at a given point at a given time will exceed a specified value, (2) the probability that the maximum concentration at a given point will exceed a specified value and (3) the probability that the residence time at a given point will exceed a specified period. PAGAP could be used as a tool for assessment purposes and risk analyses, for instance the assessment of the efficiency of a proposed remediation technique or to study the effects of parameter distribution for a given problem (sensitivity study). The model has been applied to study the greatest self sustained, precipitation controlled aquifer in North Europe, which underlies Oslo`s new major airport. 92 refs., 187 figs., 26 tabs.

Determination of trace element concentrations and stable lead, uranium and thorium isotope ratios by quadrupole-ICP-MS in NORM and NORM-polluted sample leachates

International Nuclear Information System (INIS)

Mas, J.L.; Villa, M.; Hurtado, S.; García-Tenorio, R.

2012-01-01

Highlights: ► Polluted sediment and NORM samples. ► An efficient yet fast process allowing multi-parametric determinations in 206 Pb/ 207 Pb/ 208 Pb, 238 U/ 234 U and 232 Th/ 230 Th isotope ratios using a single sample aliquot and a single instrument (ICP-QMS). Eichrom UTEVA ® extraction chromatography minicolumns were used to separate uranium and thorium in sample leachates. Independent ICP-MS determinations of uranium and thorium isotope ratios were carried out afterwards. Previously a small aliquot of the leachate was used for the determination of trace element concentrations and lead isotope ratios. Several radiochemical arrangements were tested to get maximum performances and simplicity of the method. The performances of the method were studied in terms of chemical yields of uranium and thorium and removal of the potentially interfering elements. The established method was applied to samples from a chemical industry and sediments collected in a NORM-polluted scenario. The results obtained from our method allowed us to infer not only the extent, but also the sources of the contamination in the area.

On site selection of thermoelectric power plants in polluted environment

International Nuclear Information System (INIS)

Gheorghe, A.V.

1992-01-01

This paper discusses the environmental impact of combined heat-power plants. The selection of the site of these plants depends on the spatial distribution law of pollutants and their chemical interaction with environment. The solutions of a diffusion equation describing a system of chemically interacting pollutants are given and discussed. The environmental impacts are described in terms of wind and atmosphere stability, effective and built stack height and the source distance parameters. The optimal constructive solutions are judged upon the concentrations of sulfur and nitrogen oxides at the ground level which must be kept under the maximum admissible limit. (author). 8 figs

Air pollutant concentrations near three Texas roadways, part II: Chemical characterization and transformation of pollutants

Science.gov (United States)

Clements, Andrea L.; Jia, Yuling; Denbleyker, Allison; McDonald-Buller, Elena; Fraser, Matthew P.; Allen, David T.; Collins, Donald R.; Michel, Edward; Pudota, Jayanth; Sullivan, David; Zhu, Yifang

Spatial gradients of vehicular emitted air pollutants were measured in the vicinity of three roadways in the Austin, Texas area: (1) State Highway 71 (SH-71), a heavily traveled arterial highway dominated by passenger vehicles; (2) Interstate 35 (I-35), a limited access highway north of Austin in Georgetown; and (3) Farm to Market Road 973 (FM-973), a heavily traveled surface roadway with significant truck traffic. A mobile monitoring platform was used to characterize the gradients of CO and NO x concentrations with increased distance from each roadway, while concentrations of carbonyls in the gas-phase and fine particulate matter mass and composition were measured at stationary sites upwind and at one (I-35 and FM-973) or two (SH-71) downwind sites. Regardless of roadway type or wind direction, concentrations of carbon monoxide (CO), nitric oxide (NO), and oxides of nitrogen (NO x) returned to background levels within a few hundred meters of the roadway. Under perpendicular wind conditions, CO, NO and NO x concentrations decreased exponentially with increasing distance perpendicular to the roadways. The decay rate for NO was more than a factor of two greater than for CO, and it comprised a larger fraction of NO x closer to the roadways than further downwind suggesting the potential significance of near roadway chemical processing as well as atmospheric dilution. Concentrations of most carbonyl species decreased with distance downwind of SH-71. However, concentrations of acetaldehyde and acrolein increased farther downwind of SH-71, suggesting chemical generation from the oxidation of primary vehicular emissions. The behavior of particle-bound organic species was complex and further investigation of the size-segregated chemical composition of particulate matter (PM) at increasing downwind distances from roadways is warranted. Fine particulate matter (PM 2.5) mass concentrations, polycyclic aromatic hydrocarbons (PAHs), hopanes, and elemental carbon (EC

The association between daily concentrations of air pollution and visits to a psychiatric emergency unit: a case-crossover study.

Science.gov (United States)

Oudin, Anna; Åström, Daniel Oudin; Asplund, Peter; Steingrimsson, Steinn; Szabo, Zoltan; Carlsen, Hanne Krage

2018-01-10

Air pollution is one of the leading causes of mortality and morbidity worldwide. Experimental studies, and a few epidemiological studies, suggest that air pollution may cause acute exacerbation of psychiatric disorders, and even increase the rate of suicide attempts, but epidemiological studies on air pollution in association with psychiatric disorders are still few. Our aim was to investigate associations between daily fluctuations in air pollution concentrations and the daily number of visits to a psychiatric emergency unit. Data from Sahlgrenska University Hospital, Gothenburg, Sweden, on the daily number of visits to the Psychiatric emergency unit were combined with daily data on monitored concentrations of respirable particulate matter(PM 10 ), ozone(O 3 ), nitrogen dioxides(NO 2 ) and temperature between 1st July 2012 and 31st December 2016. We used a case-crossover design to analyze data with conditional Poisson regression models allowing for over-dispersion. We stratified data on season. Visits increased with increasing PM 10 levels during the warmer season (April to September) in both single-pollutant and two-pollutant models. For example, an increase of 3.6% (95% Confidence Interval, CI, 0.4-7.0%) was observed with a 10 μg/m3 increase in PM 10 adjusted for NO 2 . In the three-pollutant models (adjusting for NO 2 and O 3 simultaneously) the increase was 3.3% (95% CI, -0.2-6.9). There were no clear associations between the outcome and NO 2 , O 3 , or PM 10 during the colder season (October to March). Ambient air particle concentrations were associated with the number of visits to the Psychiatric emergency unit in the warm season. The results were only borderline statistically significant in the fully adjusted (three-pollutant) models in this small study. The observation could be interpreted as indicative of air pollution as either exacerbating an underlying psychiatric disorder, or increasing mental distress, even in areas with comparatively low levels of

Contribution of GIS to evaluate surface water pollution by heavy metals: Case of Ichkeul Lake (Northern Tunisia)

Science.gov (United States)

Yazidi, Amira; Saidi, Salwa; Ben Mbarek, Nabiha; Darragi, Fadila

2017-10-01

The concentrations of nutrients and heavy elements in the surface water of the lake Ichkeul, main wadis which feed directly and thermal springs that flow into the lake, are measured to evaluate these chemical elements. There are used to highlight the interactions between these different aquatic compartments of Ichkeul. All metal concentrations in lake water, except Cu, were lower than the maximum permitted concentration for the protection of aquatic life. The results show that the highest concentrations are located in the eastern and south-eastern part of the lake where the polluted water comes from the lagoon of Bizerte through the wadi Tinja as well as from the city of Mateur through the wadi Joumine. The pollution indices and especially the heavy metal evaluation index (HEI) show high pollution specially located at the mouths of wadis and an increase of heavy metal concentrations, as a result of uncontrolled releases of domestic and industrial wastewater.

Concentrations of heavy metals in hair as indicators of environmental pollution

Directory of Open Access Journals (Sweden)

Baran A.

2013-04-01

Full Text Available Over 80 hair samples were collected from 38% males and 62% females in Krakow, Poland. The hairs sampled for the analysis were washed in the water-acetone-water arrangement (three times. Subsequently the hair samples were wet mineralized in a closed system HNO3:H2O2 (6:1 in a microwave furnace. Concentrations of Zn, Pb and Cd were assessed by means of ICP-OES method. Obtained results of analysis of heavy metal concentrations in the hair of tested population of Krakow inhabitants evidence environmental hazard (beside professional hazardWe observed that the hair of females showed higher levels of zinc and cadmium. Hair analysis allows for an assessment of the natural environment contamination, which is particularly important for the research on populations inhabiting areas with different degree of pollution.

A study on the environmental behavior of global air pollutants based on the continuous measurements of atmospheric radon concentrations

International Nuclear Information System (INIS)

Iida, Takao; Yamazawa, Hiromi

2003-01-01

Radon is a useful natural radioactive tracer of air transportation of atmospheric pollution, since radon is a noble gas and chemically inert. The atmospheric radon concentration is usually measured by a high-sensitivity electrostatic collection method or a two-filter method. The variations of radon concentrations observed over a solitary island and in the upper atmosphere are suitable for comparing with those of air pollutants. Some numerical simulation models were used to study the radon global transport in the atmosphere. In East Asia, atmospheric radon and air pollutants are transported with the air stream from the continent of China to the Northwestern Pacific Ocean. It is necessary to clarify the transport mechanism from both radon observations at various locations and numerical simulation. (author)

Temporal variation of persistent organic pollutant (POP) residue concentrations in sediments from the bay of Chetumal, Mexico.

Science.gov (United States)

Noreña-Barroso, E; Gold-Bouchot, G; Ceja-Moreno, V

2007-08-01

Bay of Chetumal is a transboundary priority area for the Mesoamerican Barrier Reef Systems project, which has been studied because it is the receiving body of pollutants from a large agricultural area and the city of Chetumal. Levels of persistent organic pollutants in sediments from the Bay were assessed a few years after a mass mortality event of Mayan catfish (Ariopsis assimilis) occurred in 1996. Recent sediments were collected in the rainy season (1999) and dry season (2000); results show concentrations in general lower than those reported after the fish kill, and a change of chemical profiles in chemical pollution.

Influence of the composition of radionuclide mixtures on the maximum permissible concentration

International Nuclear Information System (INIS)

Schillinger, K.; Schuricht, V.

1975-08-01

By dividing radionuclides according to their formation mechanisms it is possible to assess the influence of separate partial mixtures on the maximum permissible concentration (MPC) of the total mixture without knowing exactly their contribution to the total activity. Calculations showed that the MPC of a total mixture of unsoluble radionuclides, which may occur in all fields of peaceful uses of nuclear energy, depends on the gastrointestinal tract as the critical organ and on the composition of the fission product mixture. The influence of fractionation on the MPC can be reglected in such a case, whereas in case of soluble radionuclides this is not possible

Concentrations and (delta)13C values of atmospheric CO2 from oceanic atmosphere through time: polluted and non-polluted areas

International Nuclear Information System (INIS)

Longinelli, Antonio; Selmo, Enrico; Lenaz, Renzo; Ori, Carlo

2005-01-01

CO 2 is one of the primary agents of global climate changes. The increase of atmospheric CO 2 concentration is essentially related to human-induced emissions and, particularly, to the burning of fossil fuel whose (delta) 13 C values are quite negative. Consequently, an increase of the CO 2 concentration in the atmosphere should be paralleled by a decrease of its (delta) 13 C. Continuous and/or spot measurements of CO 2 concentrations were repeatedly carried out during the last decade and in the same period of the year along hemispheric courses from Italy to Antarctica on a vessel of the Italian National Research Program in Antarctica. During these expeditions, discrete air samples were also collected in 4-l Pyrex flasks in order to carry out precise carbon isotope analyses on atmospheric CO 2 from different areas, including theoretically 'clean' open ocean areas, with the main purpose of comparing these open ocean results with the results obtained by the National Oceanic and Atmospheric Administration/World Meteorological Organization (NOAA/WMO) at land-based stations. According to the data obtained for these two variables, a relatively large atmospheric pollution is apparent in the Mediterranean area where the CO 2 concentration has reached the value of 384 ppmv while quite negative (delta) 13 C values have been measured only occasionally. In this area, southerly winds probably help to reduce the effect of atmospheric pollution even though, despite a large variability of CO 2 concentrations, these values are consistently higher than those measured in open ocean areas by a few ppmv to about 10 ppmv. A marked, though non-continuous, pollution is apparent in the area of the Bab-el-Mandeb strait where (delta) 13 C values considerably more negative than in the Central and Southern Red Sea were measured. The concentration of atmospheric CO 2 over the Central Indian Ocean increased from about 361 ppmv at the end of 1996 to about 373 ppmv at the end of 2003 (mean growth

China's international trade and air pollution in the United States.

Science.gov (United States)

Lin, Jintai; Pan, Da; Davis, Steven J; Zhang, Qiang; He, Kebin; Wang, Can; Streets, David G; Wuebbles, Donald J; Guan, Dabo

2014-02-04

China is the world's largest emitter of anthropogenic air pollutants, and measurable amounts of Chinese pollution are transported via the atmosphere to other countries, including the United States. However, a large fraction of Chinese emissions is due to manufacture of goods for foreign consumption. Here, we analyze the impacts of trade-related Chinese air pollutant emissions on the global atmospheric environment, linking an economic-emission analysis and atmospheric chemical transport modeling. We find that in 2006, 36% of anthropogenic sulfur dioxide, 27% of nitrogen oxides, 22% of carbon monoxide, and 17% of black carbon emitted in China were associated with production of goods for export. For each of these pollutants, about 21% of export-related Chinese emissions were attributed to China-to-US export. Atmospheric modeling shows that transport of the export-related Chinese pollution contributed 3-10% of annual mean surface sulfate concentrations and 0.5-1.5% of ozone over the western United States in 2006. This Chinese pollution also resulted in one extra day or more of noncompliance with the US ozone standard in 2006 over the Los Angeles area and many regions in the eastern United States. On a daily basis, the export-related Chinese pollution contributed, at a maximum, 12-24% of sulfate concentrations over the western United States. As the United States outsourced manufacturing to China, sulfate pollution in 2006 increased in the western United States but decreased in the eastern United States, reflecting the competing effect between enhanced transport of Chinese pollution and reduced US emissions. Our findings are relevant to international efforts to reduce transboundary air pollution.

Study on the Influence of Building Materials on Indoor Pollutants and Pollution Sources

Science.gov (United States)

Wang, Yao

2018-01-01

The paper summarizes the achievements and problems of indoor air quality research at home and abroad. The pollutants and pollution sources in the room are analyzed systematically. The types of building materials and pollutants are also discussed. The physical and chemical properties and health effects of main pollutants were analyzed and studied. According to the principle of mass balance, the basic mathematical model of indoor air quality is established. Considering the release rate of pollutants and indoor ventilation, a mathematical model for predicting the concentration of indoor air pollutants is derived. The model can be used to analyze and describe the variation of pollutant concentration in indoor air, and to predict and calculate the concentration of pollutants in indoor air at a certain time. The results show that the mathematical model established in this study can be used to analyze and predict the variation law of pollutant concentration in indoor air. The evaluation model can be used to evaluate the impact of indoor air quality and evaluation of current situation. Especially in the process of building and interior decoration, through pre-evaluation, it can provide reliable design parameters for selecting building materials and determining ventilation volume.

AIR POLLUTION OF URBAN AREAS

Directory of Open Access Journals (Sweden)

MAKAROVA V. N.

2016-04-01

the area adjacent to the dump ferroalloy slag magnitude of dispersion of manganese in the atmosphere (without the background with static storage is 2.68 maximum allowable concentration. Consequently, the concentration of manganese (excluding the background on the boundary SPZ more than 2 times the maximum allowable concentration. In order to reduce the concentration to the specification value proposed limiting mass accumulation of slag on the heap, which is 936 287.6 tonnes.

Nonlinear dynamics of the atmospheric pollutants in Mexico City

Science.gov (United States)

Muñoz-Diosdado, Alejandro; Barrera-Ferrer, Amilcar; Angulo-Brown, Fernando

2014-05-01

The atmospheric pollution in the Metropolitan Zone of Mexico City (MZMC) is a serious problem with social, economical and political consequences, in virtue that it is the region which concentrates both the greatest country population and a great part of commercial and industrial activities. According to the World Health Organization, maximum permissible concentrations of atmospheric pollutants are exceeded frequently. In the MZMC, the environmental monitoring has been limited to criteria pollutants, named in this way due to when their levels are measured in the atmosphere, they indicate in a precise way the air quality. The Automatic Atmospheric Monitoring Network monitors and registers the values of pollutants concentration in air in the MZMC. Actually, it is integrated by approximately 35 automatic-equipped remote stations, which report an every-hour register. Local and global invariant quantities have been widely used to describe the fractal properties of diverse time series. In the study of certain time series, many times it is assumed that they are monofractal, which means that they can be described only with one fractal dimension. But this hypothesis is unrealistic because a lot of time series are heterogeneous and non stationary, so their scaling properties are not the same throughout time and therefore they may require more fractal dimensions for their description. Complexity of the atmospheric pollutants dynamics suggests us to analyze its time series of hourly concentration registers with the multifractal formalism. So, in this work, air concentration time series of MZMC criteria pollutants were studied with the proposed method. The chosen pollutants to perform this analysis are ozone, sulfur dioxide, carbon monoxide, nitrogen dioxide and PM10 (particles less than 10 micrometers). We found that pollutants air concentration time series are multifractal. When we calculate the degree of multifractality for each time series we know that while more

Battery lead recycling and environmental pollution hazards

Energy Technology Data Exchange (ETDEWEB)

Collivignarelli, C; Urbini, G; Riganti, V

1986-01-01

In Italy, lead recycling from discarded electric storage batteries has been developing on an industrial scale, with a yield of approximately 98% and a saving of 37% on lead imports. Moreover, battery plastic coverings can also be profitably recycled. However, the recovery industry has proved to be very polluting, as shown by the recent example of a factory sited in a vast agricultural area south of Milan, Italy. Lead in the atmosphere affects workers exposed to lead concentrations above A.C.G.I.H. standards while lead in wastewaters and fumes from smelting furnaces is the cause of environmental pollution. In particular, pollution over large tracts of cultivated lands surrounding such factories is shown by the considerable quantity of lead in forage which is harmful to cattle fed on it. Tests on dead oxen have revealed lead concentrations in kidneys and liver ranging from 9.1 to 17.4 mg/kg and 6 to 7 mg/kg respectively. Quantities exceeding safety limits have been found also in cattle blood and milk, with maximum values of 51 ..mu..g/100 ml and 0.072 mg/1 respectively. These results prove the need for extremely efficient control systems in this particular recovery industry. (author).

Phytomonitoring of air pollution around a thermal power plant

Science.gov (United States)

Agrawal, M.; Agrawal, S. B.

This study was undertaken in order to assess the impact of air pollutants on vegetation around Obra thermal power plant (1550 M W capacity) in the Mirzapur district of Uttar Pradesh. For this purpose, Mangifera indica, Citrus medico and Bouganvillaea spectabilis plants, most common at all sites, were selected as test plants. Five study sites were selected northeast (prevailing wind) of the thermal power plant. A control site was also selected at a distance of 30 km north of Obra. Responses of plants to pollutants in terms of presence of foliar injury symptoms and changes in chlorophyll, ascorbic acid and S content were measured. These changes were correlated with ambient SO 2 and suspended particulate matter (SPM) concentrations and the amount of dust settled on leaf surfaces. The SO 2 and SPM concentrations were quite high in the immediate vicinity of the power plant. There also exists a direct relationship between the concentration of SPM in air and amount of dust deposited on leaf surfaces. Maximum dust deposition was observed on M. indica plants. The levels of foliar injury, chlorophyll and ascorbic acid were found to decrease and that of S increase in plants around the power plant in comparison to those growing at a control site. The magnitude of such changes was maximum in M. indica and minimum in C. medica. A species specific direct relationship between the increase in the amount of S and decrease in chlorophyll content was observed. The study suggests that differential sensitivity of plants to SO 2 may be used in evaluating the air pollution impact around emission sources and M. indica plants can be used as an indicator plant for quantifying biological changes.

Organohalogen pollutants in herring from the northern Baltic Sea: Concentrations, congener profiles and explanatory factors

International Nuclear Information System (INIS)

Koistinen, Jaana; Kiviranta, Hannu; Ruokojaervi, Paeivi; Parmanne, Raimo; Verta, Matti; Hallikainen, Anja; Vartiainen, Terttu

2008-01-01

Organohalogen contaminants were investigated in Baltic herring caught from three catchment areas in the Baltic Sea, off the coasts of Finland. Pools of both small and large herring were analysed for polychlorinated biphenyls (PCB), dibenzo-p-dioxins, dibenzofurans, naphthalenes, camphenes (toxaphene), polybrominated diphenyl ethers and the pesticide DDT and its metabolites. PCB concentrations per fresh weight in small herring were at the same level in all catchment areas, i.e. the Bothnian Bay, the Bothnian Sea and the Gulf of Finland, revealing no hot spots and reflecting most likely long term emissions and atmospheric deposition. Differences in the levels and/or congener profiles of other contaminants between catchment areas may be explained by point sources. Similar concentrations in small and large herring in the Gulf of Finland were possibly due to their common nutrition. In the other areas, differences between small and large herring most likely reflected their different food sources. - Sources of pollutants are reflected in levels and congener profiles of pollutants in Baltic herring

The moving-window Bayesian maximum entropy framework: estimation of PM(2.5) yearly average concentration across the contiguous United States.

Science.gov (United States)

Akita, Yasuyuki; Chen, Jiu-Chiuan; Serre, Marc L

2012-09-01

Geostatistical methods are widely used in estimating long-term exposures for epidemiological studies on air pollution, despite their limited capabilities to handle spatial non-stationarity over large geographic domains and the uncertainty associated with missing monitoring data. We developed a moving-window (MW) Bayesian maximum entropy (BME) method and applied this framework to estimate fine particulate matter (PM(2.5)) yearly average concentrations over the contiguous US. The MW approach accounts for the spatial non-stationarity, while the BME method rigorously processes the uncertainty associated with data missingness in the air-monitoring system. In the cross-validation analyses conducted on a set of randomly selected complete PM(2.5) data in 2003 and on simulated data with different degrees of missing data, we demonstrate that the MW approach alone leads to at least 17.8% reduction in mean square error (MSE) in estimating the yearly PM(2.5). Moreover, the MWBME method further reduces the MSE by 8.4-43.7%, with the proportion of incomplete data increased from 18.3% to 82.0%. The MWBME approach leads to significant reductions in estimation error and thus is recommended for epidemiological studies investigating the effect of long-term exposure to PM(2.5) across large geographical domains with expected spatial non-stationarity.

The moving-window Bayesian Maximum Entropy framework: Estimation of PM2.5 yearly average concentration across the contiguous United States

Science.gov (United States)

Akita, Yasuyuki; Chen, Jiu-Chiuan; Serre, Marc L.

2013-01-01

Geostatistical methods are widely used in estimating long-term exposures for air pollution epidemiological studies, despite their limited capabilities to handle spatial non-stationarity over large geographic domains and uncertainty associated with missing monitoring data. We developed a moving-window (MW) Bayesian Maximum Entropy (BME) method and applied this framework to estimate fine particulate matter (PM2.5) yearly average concentrations over the contiguous U.S. The MW approach accounts for the spatial non-stationarity, while the BME method rigorously processes the uncertainty associated with data missingnees in the air monitoring system. In the cross-validation analyses conducted on a set of randomly selected complete PM2.5 data in 2003 and on simulated data with different degrees of missing data, we demonstrate that the MW approach alone leads to at least 17.8% reduction in mean square error (MSE) in estimating the yearly PM2.5. Moreover, the MWBME method further reduces the MSE by 8.4% to 43.7% with the proportion of incomplete data increased from 18.3% to 82.0%. The MWBME approach leads to significant reductions in estimation error and thus is recommended for epidemiological studies investigating the effect of long-term exposure to PM2.5 across large geographical domains with expected spatial non-stationarity. PMID:22739679

Willow wood production on radionuclide polluted areas

Directory of Open Access Journals (Sweden)

Rodkin Oleg I.

2010-01-01

Full Text Available ABSTRACT: One of the key environmental problems in Belarus is effective use of agricultural lands contaminated by radionuclide due to the Chernobyl disaster. The alternative method to traditional agricultural crops is fast growing willow cultivation. It is possible to use biomass of willow as renewable energy source. The goal of our investigation was the estimation of environmental aspects of willow wood production on polluted areas. The field study experiments (2007-2010 were conducted at Krichev district of Mogilev region in eastern Belarus. This region characterized by high level of Cs-137 contamination as well as high level of heavy metals pollution. In the first stage of experiments, the concentration of cesium-137 in different parts of willow biomass had been measured and transfer factor calculated. The measuring had been done for leaves, roots, and wood. To control cesium-137 accumulation in willow biomass we apply different types (nitrogen N, phosphorus P and potassium K and dose of fertilizer. The experiments show that potassium mineral fertilizer is the key factor for radionuclide accumulation control. The optimal dose of potassium is 90 kg per hectare. On the base of experimental results the model of cesium-137 accumulation in the wood for a 21 year has been developed. In accordance with calculation to the end of willow cultivation (21 year concentration of cesium-137 in wood will not be higher than permitted even with the level of cesium-137 contamination in the soil 1480 kBq/m2 (maximum 140 kqB/m2 with permitted level for firewood is 740 Bq/kg.. The concentration of cesium-137 in the roots increases gradually and get maximum in 21 year (3000 kqB/m2. Our results confirm that in the sum about 0.8 million hectares of radionuclide polluted arable lands partly excluded from agricultural practice in Belarus could be used for willow biomass production.

Temporal Variation in Air Pollution Concentrations and Preterm Birth—A Population Based Epidemiological Study

Directory of Open Access Journals (Sweden)

Bertil Forsberg

2012-01-01

Full Text Available There is growing evidence of adverse birth outcomes due to exposure to air pollution during gestation. However, recent negative studies are also reported. The aim of this study was to assess the effect of ozone and vehicle exhaust exposure (NO2 on the length of the gestational period and risk of preterm delivery. We used data from the Swedish Medical Birth Registry on all vaginally delivered singleton births in the Greater Stockholm area who were conceived during 1987–1995 (n = 115,588. Daily average levels of NO2 (from three measuring stations and ozone (two stations were used to estimate trimester and last week of gestation average exposures. Linear regression models were used to assess the association between the two air pollutants and three exposure windows, while logistic regression models were used when analyzing associations with preterm delivery ( < 37 weeks gestation. Five percent were born preterm. The median gestational period was 40 weeks. Higher levels of ozone during the first trimester were associated with shorter gestation as well as with an elevated risk of preterm delivery, the odds ratio from the most complex model was 1.06 (95% CI: 1.00–1.13 per 10 μg/m3 increase in the mean daily 8-h maximum concentration. Higher levels of ozone during the second trimester were associated with shorter gestation but the elevated risk of preterm delivery was not statistically significant. Higher levels of ozone and NO2 during the last week of gestation were associated with a shorter duration of gestation and NO2 also with preterm delivery. There were no significant associations between first and second trimester NO2 exposure estimates and studied outcomes. The effect of first trimester ozone exposure, known to cause oxidative stress, was smallest among women who conceived during autumn when vitamin D status, important for fetal health, in Scandinavian women is the highest.

Foraminiferal proxies for pollution monitoring in moderately polluted harbors

International Nuclear Information System (INIS)

Armynot du Chatelet, E.; Debenay, J.-P.; Soulard, R.

2004-01-01

Foraminiferal density and species richness that decrease with an increase in heavy metal and PAH concentration may be used as pollution indicators. - Benthic foraminifera are increasingly used as environmental bio-indicators, especially in polluted environments where their sensitivity to pollutants may be expressed by a modification of the assemblages. Eighteen sediment samples were collected in September 2000 in five harbors located in moderately polluted estuaries on the coast of Vendee (France) for the study of foraminiferal assemblages. Ten heavy metals and 13 PAH have been analyzed from the sediments. The marine to continental estuarine gradient has a prevalent influence on the foraminiferal distribution. However, the results show that foraminiferal density and species richness of the assemblages decrease with an increase in heavy metal and PAH concentration, and therefore may be used as pollution indicators. Moreover, the more polluted areas are dominated by the tolerant pioneer species Haynesina germanica that may be used as bio-indicator of pollution, mainly in the uppermost areas

Investigations for heavy metals pollution in the Nile water in Khartoum area using XRF

International Nuclear Information System (INIS)

Salih, Saadia Elsir

1998-06-01

The purpose of this study was to perform measurements for heavy metals pollution in the Nile water in Khartoum area. Ten locations were selected for the study on the white Nile, the Blue Nile and the Nile. Standard methods were used for samples collection and preparation for the measurements using XRF. Nine elements were observed and their concentrations determined in the various locations. These Ti, Cr, Fe, Cu, Zn, As, Pb, Zr, and Se. From the performed measurements for heavy metals pollution in the Nile water in Khartoum area using the XRF method the following conclusions can be made: There is no heavy metal pollution in the Nile water in Khartoum area resulting from industrial activities. However, there are indications for possible Pb pollution resulting from automobile emission. - The concentrations for the observed heavy metals, except Fe, were much below the maximum permissible international levels provided by the USA, EEC and WHO. - The origin for the observed concentrations of heavy metals, except for Pb, was considered to be soil and silt carried by river in it's journey from the Ethiopian Highlands and lake Victoria. (Author)

Effect of depositional environment and sources of pollution on uranium concentration in sediment, coral, algae and seagrass species from the Gulf of Aqaba (Red Sea)

International Nuclear Information System (INIS)

Abu-Hilal, A.H.

1994-01-01

Uranium concentrations were determined in sediment samples, four hard and two soft corals, one seagrass and four species of algae collected from phosphate-polluted sites in the northern reef area of the Gulf of Aqaba. High uranium concentrations were found in all samples examined from a phosphate-polluted site near a phosphate loading berth compared to the unpolluted ones. Uranium levels, U/Ca ratios, concentration and discrimination factors were also high compared to those reported from other regions of the world. The effects of the exported raw phosphate powder as the main source of pollution and depositional environment on the concentration of uranium in the examined species are discussed. (Author)

Air pollution modifies floral scent trails

Science.gov (United States)

McFrederick, Quinn S.; Kathilankal, James C.; Fuentes, Jose D.

Floral hydrocarbons provide essential signals to attract pollinators. As soon as they are emitted to the atmosphere, however, hydrocarbons are destroyed by chemical reactions involving pollutants such as ozone. It is therefore likely that increased air pollution interferes with pollinator attracting hydrocarbon signals. To test this hypothesis, a Lagrangian diffusion model was used to determine the position of air parcels away from hydrocarbon sources and to estimate the rate of chemical destruction of hydrocarbons as air parcels moved across the landscape. The hydrocarbon compounds linalool, β-myrcene, and β-ocimene were chosen because they are known to be common scents released from flowers. The suppressed ambient abundances of volatile organic compounds were determined in response to increased regional levels of ozone, hydroxyl, and nitrate radicals. The results indicate that the documented increases in air pollution concentrations, from pre-industrial to present times, can lead to reductions in volatile compound concentrations insects detect as they pollinate flowers. For highly reactive volatiles the maximum downwind distance from the source at which pollinators can detect the scents may have changed from kilometers during pre-industrial times to scent signals may mean that pollinators spend more time searching for patches and less time foraging. This decrease in pollinator foraging efficiency will simultaneously decrease the pollinator's reproductive output and the amount of pollen flow in flowering plants.

Background Concentrations for Use in the Operational Street Pollution Model (OSPM)

DEFF Research Database (Denmark)

Jensen, S. S.

A background model has been developed for application in the Operational Street Pollution Model (OSPM) in context of long-term exposure modelling. The back ground model is based on a semi-empirical method founded on a few monitor stations that estimates standardised one hour time-series of urban...... and rural back ground concentrations of NO2, NOx, O3 and CO for different geographic regions in Denmark. The annual mean of selected monitor stations is used as a reference year and the development in estimated traffic emissions as an index is used to establish a historic trend. As an exception ozone trends...

Solving widespread low-concentration VOC air pollution problems: Gas-phase photocatalytic oxidation answers the needs of many small businesses

Energy Technology Data Exchange (ETDEWEB)

Lyons, C; Turchi, C; Gratson, D

1995-04-01

Many small businesses are facing new regulations under the 1990 Amendments to the Clean Air Act. Regulators, as well as the businesses themselves, face new challenges to control small point-source air pollution emissions. An individual business-such as a dry cleaner, auto repair shop, bakery, coffee roaster, photo print shop, or chemical company-may be an insignificant source of air pollution, but collectively, the industry becomes a noticeable source. Often the businesses are not equipped to respond to new regulatory requirements because of limited resources, experience, and expertise. Also, existing control strategies may be inappropriate for these businesses, having been developed for major industries with high volumes, high pollutant concentrations, and substantial corporate resources. Gas-phase photocatalytic oxidation (PCO) is an option for eliminating low-concentration, low-flow-rate emissions of volatile organic compounds (VOCs) from small business point sources. The advantages PCO has over other treatment techniques are presented in this paper. This paper also describes how PCO can be applied to specific air pollution problems. We present our methodology for identifying pollution problems for which PCO is applicable and for reaching the technology`s potential end users. PCO is compared to other gas-phase VOC control technologies.

Photochemical and other air pollutants in South Holland

Energy Technology Data Exchange (ETDEWEB)

Posthumus, A.C.

1975-01-01

This year at fifteen places, regularly distributed over the industrial area west of Rotterdam, indicator plants for air pollution were again set out in the open. Tulip, gladiolus and freesia, indicators for HF, all demonstrated the same two sites to have maximum HF concentration. Spinach, an indicator for O/sub 3//SO/sub 2/, showed maximum injury in April and May and more south of the New Waterway than north of it. Medicago sativa, a plant species rather sensitive for SO/sub 2/ and O/sub 3/, showed little damage, and the reaction of petunia indicated a possible effect of ethylene only in a few cases. The photochemical air pollutant PAN caused in a few cases as well a slight injury to the indicator plants Urtica urens and Poa annua. The frequency of the injury to tobacco Bel W3 by O/sub 3//SO/sub 2/ was maximum during some periods in summer and autumn. This year again the effect of air pollution on growth and yield of tulips, tobacco and tomato plants was studied at six sites at the mouth of the Rhine with filtered and unfiltered greenhouses. The climatic conditions in these greenhouses were completely alike. Tulips in all the unfiltered greenhouses showed twice as heavy leaf injury as those in the filtered greenhouses. Tobacco plants had a higher average fresh and dry weight in the filtered greenhouses than in the unfiltered ones. The same usually held for tomato plants and also for the number of fruits and the average fresh and dry weight of tomato fruits.

MAK and BAT values list 2017. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2017-01-01

The MAK and BAT values list 2017 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

MAK and BAT values list 2016. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2016-01-01

The MAK and BAT values list 2016 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

Heavy metal pollution and forest health in the Ukrainian Carpathians

International Nuclear Information System (INIS)

Shparyk, Y.S.; Parpan, V.I.

2004-01-01

The Ukrainian Carpathians are characterized by high air pollution caused by emissions from numerous industries. We have been monitoring the state of forests in this region since 1989. The highest levels of tree defoliation (>30%) are found close to industrial emission sources and in the upper mountain forests of the Ivano-Frankivsk and Chernivtsi regions. This is caused by a combination of strong anthropogenic influences (pollution, illegal uses, recreation) as well as poor site and climatic conditions. In the Ivano-Frankivsk region, Cd and Mo accumulate in forest soils; Cr, Mo and Zn soil concentrations are higher than their limit levels; and Pb concentrations exceed toxic levels close to industrial areas (10% of the region territory). Local background levels of heavy metals are greatly exceeded in snow close to industrial regions. Analysis of correlation matrices shows that the chemical elements Ba, Cd, Co, Cr, Cu, Mo, Ni, Pb, V and Zn occur at pollution levels in natural ecosystems in the Ukrainian Carpathians. Maximum concentrations of toxic elements occur in the oak forest zone; the most industrially developed area of the region. Toxic heavy metals in the Ukrainian Carpathians forests enter with precipitation and dustfall, then become fixed in soil and accumulate in leaves, needles of vascular plants and mosses. Concentrations of these metals decrease with altitude: highest in the oak forests, less in beech, and lowest in the spruce forest zones. However, some chemical elements have the highest concentrations in spruce forests; V in needles, As in snow, and Ba and Al in soils. - Local industrial emissions of heavy metal pollution and the condition of Ukrainian Carpathians forests are examined

An assessment of dispersing pollutants from the pre-harvest burning of sugarcane in rural areas in the northeast of Brazil

Science.gov (United States)

Rangel, Maria Gabriela L.; Henríquez, Jorge R.; Costa, José A. P.; de Lira Junior, José C.

2018-04-01

In recent years, the Brazilian government has been applying several restrictions with regard to preventing environmental pollution. Although Brazilian legislation is becoming stricter as to the pre-harvest burning of sugarcane, this practice is frequently used in order to assist manual harvesting. In the northeast region of Brazil, sugarcane is an important crop, which accounts for about 15% of the national production in a total area of 1,060,660 ha, the average production being 51,119 kg per hectare. The pre-harvest burning of sugarcane generates smoke, which has a high concentration of atmospheric pollutants such as carbon dioxide (CO2), carbon monoxide (CO), particulate matter (P.M. 2.5 and 10), polycyclic aromatic hydrocarbons (PAH), volatile organic compounds (VOC) and nitrogen oxides (NOX). This article estimates the volume of CO, P.M. 2.5 and NOX generated and how they are dispersed in the atmosphere when this arises from the burning of sugarcane biomass in rural areas of Northeast Brazil, and does so by using AERMOD VIEW® simulation software. Using the characteristics of the emissions and environmental (meteorological and topographical) data, quality air profiles based on pollutant dispersion were obtained. Three studies were taken into account in order to determine the relationship between pollutant dispersion and some parameters of the burning process, such as those for the spatial distribution of resources, the duration of pre-harvest burning and the influence of undertaking burning in different months. As to spatial distribution, to divide an area into small lots contributes to decreasing the maximum concentration of pollutants by 53% compared to burning a single area of equivalent size. The study of the burning duration indicated that doing so gradually (using a lengthier procedure) could decrease the maximum concentration of the pollutants by an inverse relation. The harvesting period in this region is between November and April. The pollutants

Dynamics of the health status of children in an area with atmospheric pollution, as compared with a control group

Energy Technology Data Exchange (ETDEWEB)

Antal, A.; Coasan, A.; Vicas, T.; Balasoiu, I.; Horvath, V.; Sabau, S.

1974-01-01

The effect of air pollution on children was studied in two areas of Romania. Development, psychometric aspects, and morphological aspects were studied. Vital capacity, maximum expiratory volume, and muscular strength were examined. Adaptability and learning performance were studied in children from 7 to 14 years old. In polluted areas containing high concentrations of nitrogen oxides, sulfur dioxide, lead, and carbon black, the health of the children was impaired. Respiratory diseases were frequent, and pleurobronchopulmonary diseases, anemia, and rachitis also occurred. Scholarly performance was poorer in polluted areas than in control areas. Children in polluted areas were also shorted than in control areas.

Use of MICRAS code on the evaluation of the maximum radionuclides concentrations due to transport/migration of decay chain in groundwaters

International Nuclear Information System (INIS)

Aquino Branco, O.E. de

1995-01-01

This paper presents a methodology for the evaluation of the maximum radionuclides concentrations in groundwaters, due to the transport/migration of decay chains. Analytical solution of the equations system is difficult, even if only three elements of the decay chain are considered. Therefore, a numerical solution is most convenient. An application of the MICRAS code, developed to assess maximum concentrations of each radionuclide, starting with the initial concentrations, is presented. The maximum concentration profile for 226 Ra, calculated using MICRAS, is compared with the results obtained through an analytical and a numerical model. The fitness of results is considered good. Simplified models, like the one represented by the application of MICRAS, are largely employed in the section in the selection and characterization of sites for radioactive wastes repositories and in studies of safety evaluation for the same purpose. A detailed analysis of the transport/migration of contaminants in aquifers requires a large quantify of data from the site and from the installation as well, which makes this analysis expensive and inviable during the preliminary phases of the studies. (author). 6 refs, 1 fig, 1 tab

China’s international trade and air pollution in the United States

Science.gov (United States)

Lin, Jintai; Pan, Da; Davis, Steven J.; Zhang, Qiang; He, Kebin; Wang, Can; Streets, David G.; Wuebbles, Donald J.; Guan, Dabo

2014-01-01

China is the world’s largest emitter of anthropogenic air pollutants, and measurable amounts of Chinese pollution are transported via the atmosphere to other countries, including the United States. However, a large fraction of Chinese emissions is due to manufacture of goods for foreign consumption. Here, we analyze the impacts of trade-related Chinese air pollutant emissions on the global atmospheric environment, linking an economic-emission analysis and atmospheric chemical transport modeling. We find that in 2006, 36% of anthropogenic sulfur dioxide, 27% of nitrogen oxides, 22% of carbon monoxide, and 17% of black carbon emitted in China were associated with production of goods for export. For each of these pollutants, about 21% of export-related Chinese emissions were attributed to China-to-US export. Atmospheric modeling shows that transport of the export-related Chinese pollution contributed 3–10% of annual mean surface sulfate concentrations and 0.5–1.5% of ozone over the western United States in 2006. This Chinese pollution also resulted in one extra day or more of noncompliance with the US ozone standard in 2006 over the Los Angeles area and many regions in the eastern United States. On a daily basis, the export-related Chinese pollution contributed, at a maximum, 12–24% of sulfate concentrations over the western United States. As the United States outsourced manufacturing to China, sulfate pollution in 2006 increased in the western United States but decreased in the eastern United States, reflecting the competing effect between enhanced transport of Chinese pollution and reduced US emissions. Our findings are relevant to international efforts to reduce transboundary air pollution. PMID:24449863

Geostatistical integration and uncertainty in pollutant concentration surface under preferential sampling

Directory of Open Access Journals (Sweden)

Laura Grisotto

2016-04-01

Full Text Available In this paper the focus is on environmental statistics, with the aim of estimating the concentration surface and related uncertainty of an air pollutant. We used air quality data recorded by a network of monitoring stations within a Bayesian framework to overcome difficulties in accounting for prediction uncertainty and to integrate information provided by deterministic models based on emissions meteorology and chemico-physical characteristics of the atmosphere. Several authors have proposed such integration, but all the proposed approaches rely on representativeness and completeness of existing air pollution monitoring networks. We considered the situation in which the spatial process of interest and the sampling locations are not independent. This is known in the literature as the preferential sampling problem, which if ignored in the analysis, can bias geostatistical inferences. We developed a Bayesian geostatistical model to account for preferential sampling with the main interest in statistical integration and uncertainty. We used PM10 data arising from the air quality network of the Environmental Protection Agency of Lombardy Region (Italy and numerical outputs from the deterministic model. We specified an inhomogeneous Poisson process for the sampling locations intensities and a shared spatial random component model for the dependence between the spatial location of monitors and the pollution surface. We found greater predicted standard deviation differences in areas not properly covered by the air quality network. In conclusion, in this context inferences on prediction uncertainty may be misleading when geostatistical modelling does not take into account preferential sampling.

Concentration Levels, Pollution Characteristics and Potential Ecological Risk of Dust Heavy Metals in the Metropolitan Area of Beijing, China.

Science.gov (United States)

Xiong, Qiulin; Zhao, Wenji; Zhao, Jiayin; Zhao, Wenhui; Jiang, Lei

2017-09-30

This study aims to investigate the concentration levels, pollution characteristics and the associated potential ecological risks of the heavy metals found in dust in the metropolitan area of Beijing, China during the winter. Dust samples were collected at 49 different spatial locations of Beijing's metropolitan area from November 2013 to January 2014, in which the concentration levels of Cd, Cr, Pb, Cu, Zn, Ni, Co, V, Bi and Mo were measured by Elan DRC II type inductively coupled plasma mass spectrometry (ICP-MS). Test results showed that the concentrations of dust heavy metals Pb, Cr, Cu and Zn in the urban areas (147.1 mg·kg -1 , 195.9 mg·kg -1 , 239.2 mg·kg -1 and 713.2 mg·kg -1 ) were significantly higher than those in the suburbs (91.6 mg·kg -1 , 125.1 mg·kg -1 , 131.9 mg·kg -1 and 514.5 mg·kg -1 ). Enrichment factors and the geo-accumulation index were used to describe the pollution characteristics of dust heavy metals in urban and suburban areas. Results indicated that Zn and Cu were moderately polluting in both urban and suburban areas, Cd was severely polluting in urban areas and heavily polluting in the suburbs. Furthermore, potential ecological risk assessment revealed that the degrees of ecological harm of dust heavy metals were very strong in both urban and suburban areas, but especially in urban areas. The potential ecological risk of heavy metal Cd, whose single factor of ecological damage was extremely strong, accounted for about 90% of the total ecological risk.

Inclusion in the simulation of air pollutants recorded over the borders of test areas in Niedersachsen and forecasting of local ground level concentrations

International Nuclear Information System (INIS)

Mueller-Reissmann, K.F.; Schaffner, J.

1991-08-01

In 1987-1989 an emission-ground level concentration-model (conversion of emission into ground level concentration) was established for the pollutant sulphur dioxide (SO 2 ) by the ISP (Hannover) in cooperation with GEOS (Berlin) and was with emission data of the environs of Braunschweig for 1987 subjected to different trial runs. The pollution sources were devided into four groups: - Large Emitters (particularly power plants) - medium emitters (particularly industry) - space heating and small consumers - traffic. The pollution emitters of the first two groups were considered as point sources and the last two groups as surface sources, their emissions being evently distributed over squares of 1 km x 1 km, each surface unit of one km 2 being represented by 400 point sources in a distance of 50 m from each other. The conversion of emissions into ground level concentration is based on the Gaussian dispersion model on which also the dispersion calculation of the TA Luft (technical regulation about air pollution) is based. (orig./KW) [de

Non-destructive pollution exposure assessment in the European hedgehog (Erinaceus europaeus): II. Hair and spines as indicators of endogenous metal and As concentrations

International Nuclear Information System (INIS)

D'Have, Helga; Scheirs, Jan; Mubiana, Valentine Kayawe; Verhagen, Ron; Blust, Ronny; Coen, Wim de

2006-01-01

The role of hair and spines of the European hedgehog as non-destructive monitoring tools of metal (Ag, Al, Cd, Co, Cr, Cu, Fe, Ni, Pb, Zn) and As pollution in terrestrial ecosystems was investigated. Our results showed that mean pollution levels of a random sample of hedgehogs in Flanders are low to moderate. Yet, individual hedgehogs may be at risk for metal toxicity. Tissue distribution analyses (hair, spines, liver, kidney, muscle and fat tissue) indicated that metals and As may reach considerable concentrations in external tissues, such as hair and spines. Positive relationships were observed between concentrations in hair and those in liver, kidney and muscle for Al, Co, Cr, Cu, and Pb (0.43 < r < 0.85). Spine concentrations were positively related to liver, kidney and muscle concentrations for Cd, Co, Cr, Cu and Pb (0.37 < r < 0.62). Hair Ag, As, Fe and Zn and spine Ag, Al, As and Fe were related to metal concentrations in one or two of the investigated internal tissues (0.31 < r < 0.45). The regression models presented here may be used to predict metal and As concentrations in internal tissues of hedgehogs when concentrations in hair or spines are available. The present study demonstrated the possibility of using hair and spines for non-destructive monitoring of metal and As pollution in hedgehogs. - Hedgehog hair and spines are promising non-destructive biomonitoring tools of terrestrial metal pollution

Non-destructive pollution exposure assessment in the European hedgehog (Erinaceus europaeus): II. Hair and spines as indicators of endogenous metal and As concentrations

Energy Technology Data Exchange (ETDEWEB)

D' Have, Helga [Ecophysiology, Biochemistry and Toxicology Group, Department of Biology, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium)]. E-mail: helga.dhave@ua.ac.be; Scheirs, Jan [Evolutionary Biology Group, Department of Biology, University of Antwerp, B-2020 Antwerp (Belgium); Mubiana, Valentine Kayawe [Ecophysiology, Biochemistry and Toxicology Group, Department of Biology, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Verhagen, Ron [Evolutionary Biology Group, Department of Biology, University of Antwerp, B-2020 Antwerp (Belgium); Blust, Ronny [Ecophysiology, Biochemistry and Toxicology Group, Department of Biology, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Coen, Wim de [Ecophysiology, Biochemistry and Toxicology Group, Department of Biology, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium)

2006-08-15

The role of hair and spines of the European hedgehog as non-destructive monitoring tools of metal (Ag, Al, Cd, Co, Cr, Cu, Fe, Ni, Pb, Zn) and As pollution in terrestrial ecosystems was investigated. Our results showed that mean pollution levels of a random sample of hedgehogs in Flanders are low to moderate. Yet, individual hedgehogs may be at risk for metal toxicity. Tissue distribution analyses (hair, spines, liver, kidney, muscle and fat tissue) indicated that metals and As may reach considerable concentrations in external tissues, such as hair and spines. Positive relationships were observed between concentrations in hair and those in liver, kidney and muscle for Al, Co, Cr, Cu, and Pb (0.43 < r < 0.85). Spine concentrations were positively related to liver, kidney and muscle concentrations for Cd, Co, Cr, Cu and Pb (0.37 < r < 0.62). Hair Ag, As, Fe and Zn and spine Ag, Al, As and Fe were related to metal concentrations in one or two of the investigated internal tissues (0.31 < r < 0.45). The regression models presented here may be used to predict metal and As concentrations in internal tissues of hedgehogs when concentrations in hair or spines are available. The present study demonstrated the possibility of using hair and spines for non-destructive monitoring of metal and As pollution in hedgehogs. - Hedgehog hair and spines are promising non-destructive biomonitoring tools of terrestrial metal pollution.

A study of the concentration of certain inorganic air pollutants in the city of Elefsis

International Nuclear Information System (INIS)

Katselis, V.; Paradellis, T.

1981-11-01

The airborne concentration of Ca, Fe, Zn, Mn, Pb and Br pollutants has been measured in the city of Elefsis during 1977. The results obtained are compared with data obtained during 1975 in the same site, as well as with data obtained from the site of the NRC Democritus during 1977. (author)

A pilot study using scripted ventilation conditions to identify key factors affecting indoor pollutant concentration and air exchange rate in a residence.

Science.gov (United States)

Johnson, Ted; Myers, Jeffrey; Kelly, Thomas; Wisbith, Anthony; Ollison, Will

2004-01-01

A pilot study was conducted using an occupied, single-family test house in Columbus, OH, to determine whether a script-based protocol could be used to obtain data useful in identifying the key factors affecting air-exchange rate (AER) and the relationship between indoor and outdoor concentrations of selected traffic-related air pollutants. The test script called for hourly changes to elements of the test house considered likely to influence air flow and AER, including the position (open or closed) of each window and door and the operation (on/off) of the furnace, air conditioner, and ceiling fans. The script was implemented over a 3-day period (January 30-February 1, 2002) during which technicians collected hourly-average data for AER, indoor, and outdoor air concentrations for six pollutants (benzene, formaldehyde (HCHO), polycyclic aromatic hydrocarbons (PAH), carbon monoxide (CO), nitric oxide (NO), and nitrogen oxides (NO(x))), and selected meteorological variables. Consistent with expectations, AER tended to increase with the number of open exterior windows and doors. The 39 AER values measured during the study when all exterior doors and windows were closed varied from 0.36 to 2.29 h(-1) with a geometric mean (GM) of 0.77 h(-1) and a geometric standard deviation (GSD) of 1.435. The 27 AER values measured when at least one exterior door or window was opened varied from 0.50 to 15.8 h(-1) with a GM of 1.98 h(-1) and a GSD of 1.902. AER was also affected by temperature and wind speed, most noticeably when exterior windows and doors were closed. Results of a series of stepwise linear regression analyses suggest that (1) outdoor pollutant concentration and (2) indoor pollutant concentration during the preceding hour were the "variables of choice" for predicting indoor pollutant concentration in the test house under the conditions of this study. Depending on the pollutant and ventilation conditions, one or more of the following variables produced a small, but

A Unified Spatiotemporal Modeling Approach for Predicting Concentrations of Multiple Air Pollutants in the Multi-Ethnic Study of Atherosclerosis and Air Pollution

Science.gov (United States)

Olives, Casey; Kim, Sun-Young; Sheppard, Lianne; Sampson, Paul D.; Szpiro, Adam A.; Oron, Assaf P.; Lindström, Johan; Vedal, Sverre; Kaufman, Joel D.

2014-01-01

Background: Cohort studies of the relationship between air pollution exposure and chronic health effects require predictions of exposure over long periods of time. Objectives: We developed a unified modeling approach for predicting fine particulate matter, nitrogen dioxide, oxides of nitrogen, and black carbon (as measured by light absorption coefficient) in six U.S. metropolitan regions from 1999 through early 2012 as part of the Multi-Ethnic Study of Atherosclerosis and Air Pollution (MESA Air). Methods: We obtained monitoring data from regulatory networks and supplemented those data with study-specific measurements collected from MESA Air community locations and participants’ homes. In each region, we applied a spatiotemporal model that included a long-term spatial mean, time trends with spatially varying coefficients, and a spatiotemporal residual. The mean structure was derived from a large set of geographic covariates that was reduced using partial least-squares regression. We estimated time trends from observed time series and used spatial smoothing methods to borrow strength between observations. Results: Prediction accuracy was high for most models, with cross-validation R2 (R2CV) > 0.80 at regulatory and fixed sites for most regions and pollutants. At home sites, overall R2CV ranged from 0.45 to 0.92, and temporally adjusted R2CV ranged from 0.23 to 0.92. Conclusions: This novel spatiotemporal modeling approach provides accurate fine-scale predictions in multiple regions for four pollutants. We have generated participant-specific predictions for MESA Air to investigate health effects of long-term air pollution exposures. These successes highlight modeling advances that can be adopted more widely in modern cohort studies. Citation: Keller JP, Olives C, Kim SY, Sheppard L, Sampson PD, Szpiro AA, Oron AP, Lindström J, Vedal S, Kaufman JD. 2015. A unified spatiotemporal modeling approach for predicting concentrations of multiple air pollutants in the Multi

Spatiotemporal Characterization of Ambient PM2.5 Concentrations in Shandong Province (China).

Science.gov (United States)

Yang, Yong; Christakos, George

2015-11-17

China experiences severe particulate matter (PM) pollution problems closely linked to its rapid economic growth. Advancing the understanding and characterization of spatiotemporal air pollution distribution is an area where improved quantitative methods are of great benefit to risk assessment and environmental policy. This work uses the Bayesian maximum entropy (BME) method to assess the space-time variability of PM2.5 concentrations and predict their distribution in the Shandong province, China. Daily PM2.5 concentrations obtained at air quality monitoring sites during 2014 were used. On the basis of the space-time PM2.5 distributions generated by BME, we performed three kinds of querying analysis to reveal the main distribution features. The results showed that the entire region of interest is seriously polluted (BME maps identified heavy pollution clusters during 2014). Quantitative characterization of pollution severity included both pollution level and duration. The number of days during which regional PM2.5 exceeded 75, 115, 150, and 250 μg m(-3) varied: 43-253, 13-128, 4-66, and 0-15 days, respectively. The PM2.5 pattern exhibited an increasing trend from east to west, with the western part of Shandong being a heavily polluted area (PM2.5 exceeded 150 μg m(-3) during long time periods). Pollution was much more serious during winter than during other seasons. Site indicators of PM2.5 pollution intensity and space-time variation were used to assess regional uncertainties and risks with their interpretation depending on the pollutant threshold. The observed PM2.5 concentrations exceeding a specified threshold increased almost linearly with increasing threshold value, whereas the relative probability of excess pollution decreased sharply with increasing threshold.

Estimating cancer risk from outdoor concentrations of hazardous air pollutants in 1990

Energy Technology Data Exchange (ETDEWEB)

Woodruff, T.J.; Caldwell, J.; Cogliano, V.J.; Axelrad, D.A.

2000-03-01

A public health concern regarding hazardous air pollutants (HAPs) is their potential to cause cancer. It has been difficult to assess potential cancer risks from HAPs, due primarily to lack of ambient concentration data for the general population. The Environmental Protection Agency's Cumulative Exposure Project modeled 1990 outdoor concentrations of HAPs across the United States, which were combined with inhalation unit risk estimates to estimate the potential increase in excess cancer risk for individual carcinogenic HAPs. These were summed3d to provide an estimate of cancer risk from multiple HAPs. The analysis estimates a median excess cancer risk of 18 lifetime cancer cases per 100,000 people for all HAP concentrations. About 75% of estimated cancer risk was attributable to exposure to polycyclic organic matter, 1,3-butadiene, formaldehyde, benzene, and chromium. Consideration of some specific uncertainties, including underestimation of ambient concentrations, combining upper 95% confidence bound potency estimates, and changes to potency estimates, found that cancer risk may be underestimated by 15% or overestimated by 40--50%. Other unanalyzed uncertainties could make these under- or overestimates larger. This analysis used 1990 estimates of concentrations and can be used to track progress toward reducing cancer risk to the general population.

Concentrations and speciation of arsenic in groundwater polluted by warfare agents

International Nuclear Information System (INIS)

Daus, Birgit; Hempel, Michael; Wennrich, Rainer; Weiss, Holger

2010-01-01

Groundwater polluted with phenylarsenicals from former warfare agent deposits and their metabolites was investigated with respect to the behavior of relevant arsenic species. Depth profiles at the estimated source and at about 1 km downgradient from the source zone were sampled. The source zone is characterized by high total arsenic concentrations up to 16 mg L -1 and is dominated by organic arsenic compounds. The concentrations in the downgradient region are much lower (up to 400 μg L -1 ) and show a high proportion of inorganic arsenic species. Iron precipitation seems to be an effective mechanism to prevent dispersion of inorganic arsenic as well as phenylarsonic acid. Reductive conditions were observed in the deeper zone with predominant occurrence of trivalent arsenic species. The inorganic species are in redox equilibrium, whereas the phenylarsenic compounds have variable proportions. Methylphenylarsinic acid was identified in groundwater in traces which indicates microbial degradation activity. - The environmental fate and behavior of phenylarsenicals in groundwater are influenced by the geochemical environment.

Concentrations and speciation of arsenic in groundwater polluted by warfare agents

Energy Technology Data Exchange (ETDEWEB)

Daus, Birgit, E-mail: birgit.daus@ufz.d [UFZ - Helmholtz Centre for Environmental Research, Department of Groundwater Remediation, Permoserstrasse 15, 04318 Leipzig (Germany); Hempel, Michael [UFZ - Helmholtz Centre for Environmental Research, Department of Groundwater Remediation, Permoserstrasse 15, 04318 Leipzig (Germany); Wennrich, Rainer [Department of Analytical Chemistry, Permoserstrasse 15, 04318 Leipzig (Germany); Weiss, Holger [UFZ - Helmholtz Centre for Environmental Research, Department of Groundwater Remediation, Permoserstrasse 15, 04318 Leipzig (Germany)

2010-11-15

Groundwater polluted with phenylarsenicals from former warfare agent deposits and their metabolites was investigated with respect to the behavior of relevant arsenic species. Depth profiles at the estimated source and at about 1 km downgradient from the source zone were sampled. The source zone is characterized by high total arsenic concentrations up to 16 mg L{sup -1} and is dominated by organic arsenic compounds. The concentrations in the downgradient region are much lower (up to 400 {mu}g L{sup -1}) and show a high proportion of inorganic arsenic species. Iron precipitation seems to be an effective mechanism to prevent dispersion of inorganic arsenic as well as phenylarsonic acid. Reductive conditions were observed in the deeper zone with predominant occurrence of trivalent arsenic species. The inorganic species are in redox equilibrium, whereas the phenylarsenic compounds have variable proportions. Methylphenylarsinic acid was identified in groundwater in traces which indicates microbial degradation activity. - The environmental fate and behavior of phenylarsenicals in groundwater are influenced by the geochemical environment.

A numerical study of air pollutant dispersion with bimolecular chemical reactions in an urban street canyon using large-eddy simulation

Science.gov (United States)

Kikumoto, Hideki; Ooka, Ryozo

2012-07-01

A large-eddy simulation is performed on a turbulent dispersion of chemically reactive air pollutants in a two-dimensional urban street canyon with an aspect ratio of 1.0. Nitrogen monoxide emitted from a line-source set on the bottom of the street canyon disperses and reacts with Ozone included in a free stream. The reactions have significant influences on the concentrations of pollutants in the canyon space, and they increase the concentrations of the reaction products relative to of the concentrations of the reactants. The transport of air pollutants through a free shear layer above the canyon is closely related to the structure of the turbulence. Gases in the canyon are mainly exhausted when low-speed regions appear above the canyon. In contrast, pollutants in the free stream flow into the canyon with high-speed fluid bodies. Consequently, the correlation between the time fluctuations of the reactants' concentrations strongly affects the reaction rates in the region near the free shear layer. In this calculation, the correlation term reaches to a value of 20% of the mean reaction rate at a maximum there.

Study on the Concentration Measurement of the Pollution Gases from Coal-Fired Power Station

International Nuclear Information System (INIS)

Zheng, L J; Li, W

2006-01-01

CO 2 is a main kind of pollution gases discharged from coal-fired power station. The relationship between gas concentration and pressure, temperature is deduced base on the law of Beer-Lambert and the theory of gas line-shape. The tunable diode laser spectral technology is used to analyze the changing regularity of the peak, half-peak width of the absorption curve with pressure and temperature

A prediction study of the effect of hydrogen blending on the performance and pollutants emission of a four stroke spark ignition engine

Energy Technology Data Exchange (ETDEWEB)

Abdul-Kadim Shahad Al-Janabi, H.; Abdul-Resul Sadiq Al-Baghdadi, M. [Babylon Univ. (Iraq). Dept. of Mechanical Engineering

1999-04-01

Considering energy crises and pollution problems today, investigations have been concentrated on decreasing fuel consumption by using alternative fuels and on lowering the concentration of toxic components in combustion products. In the present work a quasi-dimensional model was developed to study the effect of hydrogen blending on fuel consumption and pollutant concentrations. The results of the study show that the maximum improvement in engine thermal efficiency occurs at 8% hydrogen blending. The results also show that 10% hydrogen blending reduces CO concentration by 73.8% but the NO concentration increases by 100%. However the problem of increasing NO concentration was solved by operating the engine with lean mixture. Hydrogen blending also reduces the specific fuel consumption until about 6% blending, then the effect becomes marginal. (Author)

Examining the concentrations of volatile organic compounds and pollutant gases in printing and copying centers in Khorramabad, Iran in 2015

Directory of Open Access Journals (Sweden)

Rajab Rashidi

2016-12-01

Full Text Available Background : Given the large amount of gaseous and aerosol pollutants produced by the printing press industry, the indoor and outdoor air quality of such centers in Khorramabad, Iran was assessed. Methods and Materials: In a descriptive study, five gaseous pollutants from among criteria air pollutants (CO, NO, NO2, SO2, O3 and volatile organic compounds (VOCs were measured. Overall, 360 samples were taken from the indoor and outdoor air of printing press centers during the two seasons of summer and winter. In addition to the direct reading sampling method, environmental sampling was also conducted. In the direct reading method, the environmental analyzer device was used to measure criteria gaseous pollutants and the phocheck5000 device was used to measure the VOCs. In the sampling by environmental pumps, SKC activated carbon absorbent tubes were used randomly/continuously during the work hours and periodically for all centers. The samples were prepared using a carbon disulfide solution and were analyzed using a gas chromatograph device. Statistical t-tests were used to analyze the results. Results: The results of the study demonstrated that, the concentrations of the all of the criteria pollutants except for the CO gas and, among the VOCs, the concentrations of benzene and toluene in the air of the printing press centers was higher than the standards set by the EPA for indoor areas. Further, there was a significant difference between the concentrations of benzene and toluene during the summer and winder seasons (p<0.05. In all the measurements carried out in summer and winter, the amount of O3 was significantly higher inside the printing press centers than that of outdoor areas (p<0.05. Conclusion: Although printing press centers cannot be considered as serious hotspots for the emission of pollutants into public places in urban areas, the pollutants produced in these centers, especially O3 can jeopardize the health of the employees of these

Indoor air pollution

International Nuclear Information System (INIS)

Qureshi, I.H.

2001-01-01

Indoor air pollution is a potential risk to human health. Prolonged exposure to indoor pollutants may cause various infectious, allergic and other diseases. Indoor pollutants can emanate from a broad array of internal and external sources. Internal sources include building and furnishing materials, consumer and commercial products, office equipment, micro-organisms, pesticides and human occupants activities. External sources include soil, water supplies and outside makeup air. The main indoor air pollutants of concern are inorganic gases, formaldehyde and other volatile organic compounds, pesticides, radon and its daughters, particulates and microbes. The magnitude of human exposure to indoor pollutants can be estimated or predicted with the help of mathematical models which have been developed using the data from source emission testing and field monitoring of pollutants. In order to minimize human exposure to indoor pollutants, many countries have formulated guidelines / standards for the maximum permissible levels of main pollutants. Acceptable indoor air quality can be achieved by controlling indoor pollution sources and by effective ventilation system for removal of indoor pollutants. (author)

Observations of atmospheric pollutants at Lhasa during 2014-2015: Pollution status and the influence of meteorological factors.

Science.gov (United States)

Duo, Bu; Cui, Lulu; Wang, Zhenzhen; Li, Rui; Zhang, Liwu; Fu, Hongbo; Chen, Jianmin; Zhang, Huifang; Qiong, A

2018-01-01

Atmospheric pollutants including SO 2 , NO 2 , CO, O 3 and inhalable particulate matter (PM 2.5 and PM 10 ) were monitored continuously from March 2014 to February 2015 to investigate characteristics of air pollution at Lhasa, Tibetan Plateau. Species exhibited similar seasonal variations except O 3 , with the peaks in winter but low valleys in summer. The maximum O 3 concentration was observed in spring, followed by summer, autumn, and winter. The positive correlation between O 3 and PM 10 in spring indicated similar sources of them, and was assumed to be turbulent transport. Temperature was the dominant meteorological factor for most species in spring. High temperature accelerates O 3 photochemistry, and favors air disturbance which is conductive to dust resuspension in spring. Relative humidity (RH) and atmospheric pressure were the main meteorological factors in summer. RH showed negative correlations with species, while atmospheric pressure posed opposite situation. Wind speed (WS) was the dominant meteorological factor in autumn, the negative correlations between WS and species indicated diffusion by wind. Most species showed non-significant correlations with meteorological factors in winter, indicating the dependence of pollution on source emission rather than restriction by meteorology. Pollution weather character indicated that emissions were from biomass burning and dust suspension, and meteorological factors also played an important role. Air stream injection from the stratosphere was observed during O 3 pollution period. Air parcels from Southwest Asia were observed during air pollution period in winter. An enhancement in air pollutants such as O 3 would be expected in the future, more attention should be given to countermeasures for prevention of air pollution in the future. Copyright © 2017. Published by Elsevier B.V.

Soil pollution by oxidation of tailings from toxic spill of a pyrite mine

International Nuclear Information System (INIS)

Simon, M.; Martin, F.; Ortiz, I.; Garcia, I.; Fernandez, J.; Fernandez, E.; Dorronsoro, C.; Aguilar, J.

2001-01-01

On the 25th April 1998, toxic water and tailings from a pyrite mine of Aznalcollar (southern Spain) spilled into the Agrio and Guadiamar River Basin affecting some 40 km 2 . In five sectors throughout the basin, we monitored the physical and chemical properties of the tailings as well as the degree of pollution in the soils on four different sampling dates: 5 May, 20 May, 4 June and 22 July 1998. The characteristics of the tailings deposited on the soils are shown to be related to distance from the spill. The oxidation rate of the tailings and the solubilization of the pollutant elements were more pronounced in the middle and lower sectors of the basin, where the particle size was finer, the sulfur content higher and the bulk density less. The increases in water-soluble sulfates, Zn, Cd and Cu were very rapid (the highest values being reached 25 days after the spill) and intense (reaching 45% of the total Cu, 65% of the total Zn and Cd). Meanwhile, the increases in water-soluble As, Bi, Sb, Pb and Tl were far lower (ranging between 0.002% of the total Tl and 2.5% of the total As) and less rapid in the case of As, Bi and Pb (the highest values for these elements being reached 40 days after the spill). These soluble elements infiltrated the soils with the rainwater, swiftly augmenting the soil pollution. Twenty-five days after the spill, when the rainfall ranged between 45 and 63 mm, the first 10-cm of the soils in the middle and lower sectors of the basin exceeded the maximum concentration permitted for agricultural soils in Zn, Cu and Tl. At 40 days after the spill, when the rainfall ranged between 60 and 89 mm, all the soils reached or exceeded the maximum permitted concentrations for As and Tl. Nevertheless, the pollutants tended to concentrate in the first 10 cm of the soils without seriously contaminating either the subsoil or the groundwaters. Consequently, a rapid removal of the tailings and the ploughing of the first 25-30 cm of the soils would be urgent

Ambient concentrations and personal exposure to polycyclic aromatic hydrocarbons (PAH) in an urban community with mixed sources of air pollution

Science.gov (United States)

ZHU, XIANLEI; FAN, ZHIHUA (TINA); WU, XIANGMEI; JUNG, KYUNG HWA; OHMAN-STRICKLAND, PAMELA; BONANNO, LINDA J.; LIOY, PAUL J.

2014-01-01

Assessment of the health risks resulting from exposure to ambient polycyclic aromatic hydrocarbons (PAH) is limited by a lack of environmental exposure data among the general population. This study characterized personal exposure and ambient concentrations of PAH in the Village of Waterfront South (WFS), an urban community with many mixed sources of air toxics in Camden, New Jersey, and CopeWood/Davis Streets (CDS), an urban reference area located ~1 mile east of WFS. A total of 54 and 53 participants were recruited from non-smoking households in WFS and CDS, respectively. In all, 24-h personal and ambient air samples were collected simultaneously in both areas on weekdays and weekends during summer and winter. The ambient PAH concentrations in WFS were either significantly higher than or comparable to those in CDS, indicating the significant impact of local sources on PAH pollution in WFS. Analysis of diagnostic ratios and correlation suggested that diesel truck traffic, municipal waste combustion and industrial combustion were the major sources in WFS. In such an area, ambient air pollution contributed significantly to personal PAH exposure, explaining 44–96% of variability in personal concentrations. This study provides valuable data for examining the impact of local ambient PAH pollution on personal exposure and therefore potential health risks associated with environmental PAH pollution. PMID:21364704

MAK and BAT values list 2015. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2015-01-01

The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2015 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

MAK and BAT values list 2014. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2014-01-01

The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2014 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

Development and evaluation of SBLINE, a suite of models for the prediction of pollution concentrations from vehicles in urban areas

Energy Technology Data Exchange (ETDEWEB)

Namdeo, A.K.; Colls, J.J. [Environmental Science, University of Nottingham, Loughborough (United Kingdom)

1996-09-06

The assessment of air quality impacts from roadways is a major concern to urban planners, developers, health officials and engineers. This paper describes the development of a suite of models, called SBLINE, for prediction of pollution concentrations from vehicles in urban road networks. The first component of the suite is ROADFAC, an emission model for calculating emission rates for a road link with known vehicle fleet structure and operational details. ROADFAC can also calculate modal emission rates, caused by deceleration, idle, acceleration and cruise operational modes, by determining queue length and vehicle delay from traffic volume and signal phasing information. The other components of SBLINE are two dispersion models, called NOTLINE and CPB, for prediction of pollution concentrations contributed by different roadlinks in the network. These models use site geometry, meteorology, and traffic emissions calculated by ROADFAC to predict pollutant concentrations. The contribution from a given link is calculated by using NOTLINE if that link is situated in simple topography, or CPB is run if the link is inside a canyon or a cut-section. Finally, cumulative concentrations at any receptor location are calculated by adding the contributions from all roadlinks. SBLINE can be applied to any urban network of roads, with roadlinks located in either simple topography or street canyons. The program has been evaluated in one region of Leicester in the UK. The region represents a typical urban network of roads with some roads located in plain topography and some inside medium size canyons. Observed values of pollutant concentrations are compared with predictions made from detailed measurements of the vehicle population parameters, meteorology, and local street and building topography. Well-established statistical techniques have been used to show the potential of SBLINE for application to other road networks

Risk of a false decision on conformity of an environmental compartment due to measurement uncertainty of concentrations of two or more pollutants.

Science.gov (United States)

Pennecchi, Francesca R; Kuselman, Ilya; da Silva, Ricardo J N B; Hibbert, D Brynn

2018-07-01

Risks of false decisions in conformity assessment of an environmental compartment due to measurement uncertainty of concentrations of two or more pollutants are discussed. Even if the assessment of conformity for each pollutant in the compartment is successful, the total probability of a false decision concerning the compartment as a whole might still be significant. A model of the total probability of a false decision, formulated on the base of the law of total probability, is used, for example, for a study of test results of total suspended particulate matter (TSPM) concentration in ambient air near to three independent stone quarries located in Israel, as the sources of the air pollution. Total probabilities of underestimation of TSPM concentration (total risk of the inhabitants) and overestimation (total risk of the stone producers) are evaluated as a combination of the particular risks of air conformity assessment concerning TSPM concentration for each quarry. These probabilities characterize conformity of the TSPM concentration in the region of the quarries as a whole. Core code developed in R programming environment for the calculations is provided. Copyright © 2018 Elsevier Ltd. All rights reserved.

[APPROACHES TO URBAN AREA RANKING ACCORDINGLY TO THE LEVEL OF HEAVY METAL POLLUTION].

Science.gov (United States)

Stepanova, N V; Valeeva, E R; Fomina, S F

2015-01-01

Urban area ranking was performed according to the level of the heavy metal pollution based on the data of the snow and soil chemical characteristics. With reference to cumulative rates of the snow cover and soil pollution by heavy metals in the territory of the city of Kazan there were selected four areas: I--Derbyshki; II--Teplocontrol; III--Gorki; IV--Kirovsky district. The pollution level of snow cover in the territory of the city was determined by pollution level indices calculated with the application of Maximum Permissible Concentration (MPC) of chemical substances in ambient waters for household and recreational and service facilities use. The assessment of the pollution level in soils in the city showed the total territory of Kazan to be mildly polluted by manganese, concerning other heavy metals the categories of the soil pollution vary on areas. Results of hair biological monitoring in children are an informative auxiliary tool for the evaluation of the present ecological situation concerning heavy metals in certain territories of the city.

[Exploring the Severe Haze in Beijing During December, 2015: Pollution Process and Emissions Variation].

Science.gov (United States)

Xue, Yi-feng; Zhou, Zhen; Nie, Teng; Pan, Tao; Qi, Jun; Nie, Lei; Wang, Zhan-shan; Li, Yun-ting; Li, Xue-feng; Tian, He-zhong

2016-05-15

Severe haze episodes shrouded Beijing and its surrounding regions again during December, 2015, causing major environmental and health problems. Beijing authorities had launched two red alerts for atmospheric heavy pollution in this period, adopted a series of emergency control measures to reduce the emissions from major pollution sources. To better understand the pollution process and emissions variation during these extreme pollution events, we performed a model-assisted analysis of the hourly observation data of PM₂.₅, and meteorological parameters combined with the emissions variation of pollution sources. The synthetic analysis indicated that: (1) Compared with the same period of last year, the emissions of atmospheric pollution sources decreased in December 2015. However, the emission levels of primary pollutants were still rather high, which were the main intrinsic causes for haze episodes, and the unfavorable diffusion conditions represented the important external factor. High source emissions and meteorological factors together led to this heavy air pollution process. (2) Emergency control measures taken by the red alert for heavy air pollution could decrease the pollutants emission by about 36% and the PM₂.₅ concentrations by 11% to 21%. Though the implementation of red alert could not reverse the evolution trend of heavier pollution, it indeed played an active role in mitigation of PM₂.₅ pollution aggravating. (3) Under the heavy pollution weather conditions, air pollutants continued to accumulate in the atmosphere, and the maximum effect by taking emergency measures occurred 48-72 hours after starting the implementation; therefore, the best time for executing emergency measures should be 36-48 hours before the rapid rise of PM₂.₅ concentration, which requires a more powerful demand on the accuracy of air quality forecast.

Identification of key factors affecting the water pollutant concentration in the sluice-controlled river reaches of the Shaying River in China via statistical analysis methods.

Science.gov (United States)

Dou, Ming; Zhang, Yan; Zuo, Qiting; Mi, Qingbin

2015-08-01

The construction of sluices creates a strong disturbance in water environmental factors within a river. The change in water pollutant concentrations of sluice-controlled river reaches (SCRRs) is more complex than that of natural river segments. To determine the key factors affecting water pollutant concentration changes in SCRRs, river reaches near the Huaidian Sluice in the Shaying River of China were selected as a case study, and water quality monitoring experiments based on different regulating modes were implemented in 2009 and 2010. To identify the key factors affecting the change rates for the chemical oxygen demand of permanganate (CODMn) and ammonia nitrogen (NH3-N) concentrations in the SCRRs of the Huaidian Sluice, partial correlation analysis, principal component analysis and principal factor analysis were used. The results indicate four factors, i.e., the inflow quantity from upper reaches, opening size of sluice gates, water pollutant concentration from upper reaches, and turbidity before the sluice, which are the common key factors for the CODMn and NH3-N concentration change rates. Moreover, the dissolved oxygen before a sluice is a key factor for the permanganate concentration from CODMn change rate, and the water depth before a sluice is a key factor for the NH3-N concentration change rate. Multiple linear regressions between the water pollutant concentration change rate and key factors were established via multiple linear regression analyses, and the quantitative relationship between the CODMn and NH3-N concentration change rates and key affecting factors was analyzed. Finally, the mechanism of action for the key factors affecting the water pollutant concentration changes was analyzed. The results reveal that the inflow quantity from upper reaches, opening size of sluice gates, permanganate concentration from CODMn from upper reaches and dissolved oxygen before the sluice have a negative influence and the turbidity before the sluice has a positive

Seawater Polluted with Highly Concentrated Polycyclic Aromatic Hydrocarbons Suppresses Osteoblastic Activity in the Scales of Goldfish, Carassius auratus.

Science.gov (United States)

Suzuki, Nobuo; Sato, Masayuki; Nassar, Hossam F; Abdel-Gawad, Fagr Kh; Bassem, Samah M; Yachiguchi, Koji; Tabuchi, Yoshiaki; Endo, Masato; Sekiguchi, Toshio; Urata, Makoto; Hattori, Atsuhiko; Mishima, Hiroyuki; Shimasaki, Youhei; Oshima, Yuji; Hong, Chun-Sang; Makino, Fumiya; Tang, Ning; Toriba, Akira; Hayakawa, Kazuichi

2016-08-01

We have developed an original in vitro bioassay using teleost scale, that has osteoclasts, osteoblasts, and bone matrix as each marker: alkaline phosphatase (ALP) for osteoblasts and tartrate-resistant acid phosphatase (TRAP) for osteoclasts. Using this scale in vitro bioassay, we examined the effects of seawater polluted with highly concentrated polycyclic aromatic hydrocarbons (PAHs) and nitro-polycyclic aromatic hydrocarbons (NPAHs) on osteoblastic and osteoclastic activities in the present study. Polluted seawater was collected from two sites (the Alexandria site on the Mediterranean Sea and the Suez Canal site on the Red Sea). Total levels of PAHs in the seawater from the Alexandria and Suez Canal sites were 1364.59 and 992.56 ng/l, respectively. We were able to detect NPAHs in both seawater samples. Total levels of NPAHs were detected in the seawater of the Alexandria site (12.749 ng/l) and the Suez Canal site (3.914 ng/l). Each sample of polluted seawater was added to culture medium at dilution rates of 50, 100, and 500, and incubated with the goldfish scales for 6 hrs. Thereafter, ALP and TRAP activities were measured. ALP activity was significantly suppressed by both polluted seawater samples diluted at least 500 times, but TRAP activity did not change. In addition, mRNA expressions of osteoblastic markers (ALP, osteocalcin, and the receptor activator of the NF-κB ligand) decreased significantly, as did the ALP enzyme activity. In fact, ALP activity decreased on treatment with PAHs and NPAHs. We conclude that seawater polluted with highly concentrated PAHs and NPAHs influences bone metabolism in teleosts.

Behavioral responses of the estuarine calanoid copepod Eurytemora affinis to sub-lethal concentrations of waterborne pollutants

International Nuclear Information System (INIS)

Michalec, François-Gaël; Holzner, Markus; Menu, Dominique; Hwang, Jiang-Shiou; Souissi, Sami

2013-01-01

Highlights: •We studied the effects of sub-lethal exposure to pollutants on Eurytemora affinis swimming behavior. •Nonylphenol, cadmium and polycyclic aromatic hydrocarbons caused hyperactivity. •Effects were observable within 30 min of exposure and persisted during a depuration period. •The response resembles an escape reaction allowing copepods to evade stressful conditions. -- Abstract: Estuarine waters contain a variety of chemicals which affect to various extents the behavior of aquatic organisms. Little is known, however, on the behavioral response of copepods. The present study shows the results of laboratory experiments investigating the immediate effects of sub-lethal concentrations of three commonly found contaminants on the three-dimensional swimming behavior of the estuarine calanoid copepod Eurytemora affinis. Nonylphenol at 2 μg L −1 , cadmium at 45 ng L −1 and a mixture of low to medium molecular weight polycyclic aromatic hydrocarbons at 40 ng L −1 all affected the swimming behavior of E. affinis adults, increasing both swimming speed and activity. In most cases, effects were observable within 30 min of exposure and persisted or faded during a period of depuration in uncontaminated water of similar duration. In ovigerous females exposed to Cd and PAHs, effects appeared to be more pronounced during the depuration period, suggesting that carrying ovisacs may impair recovery. We quantified differences in the distribution of swimming speed values by considering the relative frequencies of periods of break, slow and fast swimming and we observed a trend toward faster movements in the presence of pollutants. The degree of trajectory complexity, estimated through their fractal dimension, was unaffected by pollutants. Since both narcotic and non-narcotic pollutants induced hyperactivity, our results suggest that changes in behavior after a short-term exposure may be independent of the general mode of action of the chemicals. The increase in

Behavioral responses of the estuarine calanoid copepod Eurytemora affinis to sub-lethal concentrations of waterborne pollutants

Energy Technology Data Exchange (ETDEWEB)

Michalec, François-Gaël [Université Lille Nord de France, F-59000 Lille (France); USTL, LOG, Station Marine de Wimereux, F-62930 Wimereux (France); CNRS, UMR 8187, F-62930 Wimereux (France); National Taiwan Ocean University, Institute of Marine Biology, Keelung, Taiwan, ROC (China); Holzner, Markus [Institute of Environmental Engineering, ETH Zürich (Switzerland); Menu, Dominique [Université Lille Nord de France, F-59000 Lille (France); USTL, LOG, Station Marine de Wimereux, F-62930 Wimereux (France); CNRS, UMR 8187, F-62930 Wimereux (France); Hwang, Jiang-Shiou [National Taiwan Ocean University, Institute of Marine Biology, Keelung, Taiwan, ROC (China); Souissi, Sami, E-mail: sami.souissi@univ-lille1.fr [Université Lille Nord de France, F-59000 Lille (France); USTL, LOG, Station Marine de Wimereux, F-62930 Wimereux (France); CNRS, UMR 8187, F-62930 Wimereux (France)

2013-08-15

Highlights: •We studied the effects of sub-lethal exposure to pollutants on Eurytemora affinis swimming behavior. •Nonylphenol, cadmium and polycyclic aromatic hydrocarbons caused hyperactivity. •Effects were observable within 30 min of exposure and persisted during a depuration period. •The response resembles an escape reaction allowing copepods to evade stressful conditions. -- Abstract: Estuarine waters contain a variety of chemicals which affect to various extents the behavior of aquatic organisms. Little is known, however, on the behavioral response of copepods. The present study shows the results of laboratory experiments investigating the immediate effects of sub-lethal concentrations of three commonly found contaminants on the three-dimensional swimming behavior of the estuarine calanoid copepod Eurytemora affinis. Nonylphenol at 2 μg L{sup −1}, cadmium at 45 ng L{sup −1} and a mixture of low to medium molecular weight polycyclic aromatic hydrocarbons at 40 ng L{sup −1} all affected the swimming behavior of E. affinis adults, increasing both swimming speed and activity. In most cases, effects were observable within 30 min of exposure and persisted or faded during a period of depuration in uncontaminated water of similar duration. In ovigerous females exposed to Cd and PAHs, effects appeared to be more pronounced during the depuration period, suggesting that carrying ovisacs may impair recovery. We quantified differences in the distribution of swimming speed values by considering the relative frequencies of periods of break, slow and fast swimming and we observed a trend toward faster movements in the presence of pollutants. The degree of trajectory complexity, estimated through their fractal dimension, was unaffected by pollutants. Since both narcotic and non-narcotic pollutants induced hyperactivity, our results suggest that changes in behavior after a short-term exposure may be independent of the general mode of action of the chemicals. The

Effects of SO/sub 2/ and NO/sub 2/ polluted air upon the ultrastructure of chloroplasts

Energy Technology Data Exchange (ETDEWEB)

Wellburn, A r; Majernik, O; Wellburn, F A.M.

1972-01-01

The ultrastructure of mature bean tissue exposed to air polluted by various concentrations of SO/sub 2/ or no2 at maximum stomatal aperture for short periods was compared with similar unpolluted tissue, using an electron microscope. Both pollutants caused swelling of the thylakoids within the chloroplasts, but not extra-chloroplastidic damage was detected. This thylakoid swelling could be reversed by removing the pollutant from the air flow or changing the rate of gas flow within the tissue. The phenomenon is discussed in relation to previously-reported diminution in the rate of photosynthesis when higher plants are exposed to either SO/sub 2/ or NO/sub 2/.

Response of soil microbial activity and biodiversity in soils polluted with different concentrations of cypermethrin insecticide.

Science.gov (United States)

Tejada, Manuel; García, Carlos; Hernández, Teresa; Gómez, Isidoro

2015-07-01

We performed a laboratory study into the effect of cypermethrin insecticide applied to different concentrations on biological properties in two soils [Typic Xerofluvent (soil A) and Xerollic Calciorthid (soil B)]. Two kg of each soil were polluted with cypermethrin at a rate of 60, 300, 600, and 1,200 g ha(-1) (C1, C2, C3, and C4 treatments). A nonpolluted soil was used as a control (C0 treatment). For all treatments and each experimental soil, soil dehydrogenase, urease, β-glucosidase, phosphatase, and arylsulphatase activities and soil microbial community were analysed by phospholipid fatty acids, which were measured at six incubation times (3, 7, 15, 30, 60, and 90 days). The behavior of the enzymatic activities and microbial population were dependent on the dose of insecticide applied to the soil. Compared with the C0 treatment, in soil A, the maximum inhibition of the enzymatic activities was at 15, 30, 45, and 90 days for the C1, C2, C3, and C4 treatments, respectively. However, in soil B, the maximum inhibition occurred at 7, 15, 30, and 45 days for the C1, C2, C3, and C4 treatments, respectively. These results suggest that the cypermethrin insecticide caused a negative effect on soil enzymatic activities and microbial diversity. This negative impact was greater when a greater dose of insecticide was used; this impact was also greater in soil with lower organic matter content. For both soils, and from these respective days onward, the enzymatic activities and microbial populations progressively increased by the end of the experimental period. This is possibly due to the fact that the insecticide or its breakdown products and killed microbial cells, subsequently killed by the insecticide, are being used as a source of energy or as a carbon source for the surviving microorganisms for cell proliferation.

Air pollution

International Nuclear Information System (INIS)

Nelson, P.

2000-01-01

Australian cites experience a number of current and emerging air pollution problems. Concentrations of traditional primary pollutants such as CO, lead and dust have fallen in recent years as a consequence of air pollutant control measures, and the widespread introduction of lead-free petrol. However, recommended guidelines for ozone, the principal component of photochemical smog, are regularly exceeded in major capital cities in the summer months. In addition, it is predicted that extensive urban expansion will lead to much greater dependence on the motor vehicle as the primary means of transportation. Effects of air pollution are felt at a variety of scales. Traditionally, concerns about gaseous and particulate emissions from industrial and vehicular sources were focused on local impacts due to exposure to toxic species such as CO and lead. As noted above, concentrations of these pollutants have been reduced by a variety of control measures. Pollutants which have effects at a regional scale, such as photochemically-produced ozone, and acidic gases and particles have proved more difficult to reduce. In general, these pollutants arc not the result of direct emissions to atmosphere, but result from complex secondary processes driven by photochemical reactions of species such as NO 2 and aldehydes. In addition, global effects of gaseous and particulate emissions to the atmosphere have received significant recent attention, concentrations of atmospheric CO 2 with predicted impacts on global climate, and ozone depletion due to anthropogenic emissions of chlorine-containing chemicals are the two major examples. Combustion processes from petrol- and diesel-fuelled vehicles, make major contributions to air pollution, and the magnitude of this contribution is discussed in this article

Degradation of air polluted by organic compounds

International Nuclear Information System (INIS)

Santoyo O, E.L.; Lizama S, B.E.; Vazquez A, O.; Luna C, P.C.; Arredondo H, S.

1999-01-01

According to the Mexican standard NOM-010-STPS-1994 it has been established concentrations of maximum permissible levels in workable air for styrene in the range 420-1710 mg/m 3 and for xylene between 218-870 mg/m 3 . In this work it is studied a biological treatment (bio filtration) for air polluted by xylene and styrene where the microorganisms are adhered at synthetic fiber, these degrade to the organic compounds that across in gaseous state and they are mineralized toward CO 2 and H 2 O. The characteristics of temperature, p H, concentration of organic compound and mineral parameters, as well as, the biomass quantity have been optimized for that bio filters efficiency were greater than those reported in other works. (Author)

Pollutants transport and atmospheric variability of CO2 over Siberia: contribution of airborne measurements

International Nuclear Information System (INIS)

Paris, J.D.

2008-12-01

The work presented here intends to characterize the variations of atmospheric concentrations of CO 2 , CO, O 3 and ultrafine particles, over a large scale aircraft transect above Siberia, during three intensive YAK-AEROSIB campaigns in April 2006, September 2006 and August 2007, respectively. Pollutant and greenhouse gases distribution in this poorly studied region is needed to model atmospheric long range transport. I show here that CO concentrations at the time of the campaigns is broadly affected by (1) advection of Chinese pollutants through baro-clinic perturbations, (2) advection (diffuse or not) of European pollutants at various altitudes, (3) and of biomass burning from Central Asia. This set of factors is analyzed through a novel statistical technique based on clustering of backward transport simulated by the FLEXPART Lagrangian model. Large observed CO 2 gradients in summer are matched against vertical mixing in GCM simulated CO 2 . At last I present ultrafine particle measurements, and a possible nucleation summer maximum in the clean, continental mid-troposphere. (author)

Benefits of the maximum tolerated dose (MTD) and maximum tolerated concentration (MTC) concept in aquatic toxicology

International Nuclear Information System (INIS)

Hutchinson, Thomas H.; Boegi, Christian; Winter, Matthew J.; Owens, J. Willie

2009-01-01

development of sound criteria for data interpretation when the exposure of organisms has exceeded the MTD. While the MTD approach is well established for oral, topical, inhalational or injection exposure routes in mammalian toxicology, we propose that for exposure of aquatic organisms via immersion, the term Maximum Tolerated Concentration (MTC) is more appropriate

Non-destructive pollution exposure assessment in the European hedgehog (Erinaceus europaeus): II. Hair and spines as indicators of endogenous metal and As concentrations.

Science.gov (United States)

D'Havé, Helga; Scheirs, Jan; Mubiana, Valentine Kayawe; Verhagen, Ron; Blust, Ronny; De Coen, Wim

2006-08-01

The role of hair and spines of the European hedgehog as non-destructive monitoring tools of metal (Ag, Al, Cd, Co, Cr, Cu, Fe, Ni, Pb, Zn) and As pollution in terrestrial ecosystems was investigated. Our results showed that mean pollution levels of a random sample of hedgehogs in Flanders are low to moderate. Yet, individual hedgehogs may be at risk for metal toxicity. Tissue distribution analyses (hair, spines, liver, kidney, muscle and fat tissue) indicated that metals and As may reach considerable concentrations in external tissues, such as hair and spines. Positive relationships were observed between concentrations in hair and those in liver, kidney and muscle for Al, Co, Cr, Cu, and Pb (0.43 Spine concentrations were positively related to liver, kidney and muscle concentrations for Cd, Co, Cr, Cu and Pb (0.37 spine Ag, Al, As and Fe were related to metal concentrations in one or two of the investigated internal tissues (0.31 hedgehogs when concentrations in hair or spines are available. The present study demonstrated the possibility of using hair and spines for non-destructive monitoring of metal and As pollution in hedgehogs.

The role of catchment vegetation in reducing atmospheric inputs of pollutant aerosols in Ganga river.

Science.gov (United States)

Shubhashish, Kumar; Pandey, Richa; Pandey, Jitendra

2012-08-01

The role of woody perennials in the Ganga river basin in modifying the run-off quality as influenced by atmospheric deposition of pollutant aerosols was investigated. The concentration of seven nutrients and eight metals were measured in atmospheric deposits as well as in run-off water under the influence of five woody perennials. Nutrient retention was recorded maximum for Bougainvillea spectabilis ranged from 4.30 % to 33.70 %. Metal retention was recorded highest for Ficus benghalensis ranged from 5.15 % to 36.98 %. Although some species showed nutrient enrichment, all the species considered in the study invariably contribute to reduce nutrients and metal concentration in run-off water. Reduction in run off was recorded maximum for B. spectabilis (nutrient 6.48 %-40.66 %; metal 7.86 %-22.85 %) and minimum for Ficus religiosa (nutrient 1.68 %-27.19 %; metal 6.55 %-31.55 %). The study forms the first report on the use of woody perennials in reducing input of atmospheric pollutants to Ganga river and has relevance in formulating strategies for river basin management.

The financial implications of certain types of cross-border pollution: The polluter-pays principle

International Nuclear Information System (INIS)

Montmayeul, J.P.

2001-01-01

Favorable Paris Convention regulations: absolute liability, exclusive liability, channeling of liability to the operator in case of nuclear damage, financial security, limited maximum liability, single legal forum, ten-year time limit. Difficulties of application for certain types of cross-border pollution not covered by the Paris Convention: so-called orphan sources (stolen, lost, or abandoned sealed sources or confiscated contaminated metallurgical scrap). Benefits of the polluter-pays principle: identification of the polluter, identification of the holder of the polluted materials, responsible parties held accountable, financial reparations. Analysis of the polluter-pays principle already recognized in numerous international texts on environmental law. (author)

Regression trees modeling and forecasting of PM10 air pollution in urban areas

Science.gov (United States)

Stoimenova, M.; Voynikova, D.; Ivanov, A.; Gocheva-Ilieva, S.; Iliev, I.

2017-10-01

Fine particulate matter (PM10) air pollution is a serious problem affecting the health of the population in many Bulgarian cities. As an example, the object of this study is the pollution with PM10 of the town of Pleven, Northern Bulgaria. The measured concentrations of this air pollutant for this city consistently exceeded the permissible limits set by European and national legislation. Based on data for the last 6 years (2011-2016), the analysis shows that this applies both to the daily limit of 50 micrograms per cubic meter and the allowable number of daily concentration exceedances to 35 per year. Also, the average annual concentration of PM10 exceeded the prescribed norm of no more than 40 micrograms per cubic meter. The aim of this work is to build high performance mathematical models for effective prediction and forecasting the level of PM10 pollution. The study was conducted with the powerful flexible data mining technique Classification and Regression Trees (CART). The values of PM10 were fitted with respect to meteorological data such as maximum and minimum air temperature, relative humidity, wind speed and direction and others, as well as with time and autoregressive variables. As a result the obtained CART models demonstrate high predictive ability and fit the actual data with up to 80%. The best models were applied for forecasting the level pollution for 3 to 7 days ahead. An interpretation of the modeling results is presented.

A novel method to construct an air quality index based on air pollution profiles.

Science.gov (United States)

Thach, Thuan-Quoc; Tsang, Hilda; Cao, Peihua; Ho, Lai-Ming

2018-01-01

Air quality indices based on the maximum of sub-indices of pollutants are easy to produce and help quantify the degree of air pollution. However, they discount the additive effects of multiple pollutants and are only sensitive to changes in highest sub-index. We propose a simple and concise method to construct an air quality index that takes into account additive effects of multiple pollutants and evaluate the extent to which this index predicts health effects. We obtained concentrations of four criteria pollutants: particulate matter with aerodynamic diameter ≤ 10μm (PM 10 ), sulphur dioxide (SO 2 ), nitrogen dioxide (NO 2 ) and ozone (O 3 ) and daily admissions to Hong Kong hospitals for cardiovascular and respiratory diseases for all ages and those 65 years or older for years 2001-2012. We derived sub-indices of the four criteria pollutants, calculated by normalizing pollutant concentrations to their respective short-term WHO Air Quality Guidelines (WHO AQG). We aggregated the sub-indices using the root-mean-power function with an optimal power to form an overall air quality index. The optimal power was determined by minimizing the sum of over- and under-estimated days. We then assessed associations between the pollution bands of the index and cardiovascular and respiratory admissions using a time-stratified case-crossover design adjusted for ambient temperature, relative humidity and influenza epidemics. Further, we conducted case-crossover analyses using the Hong Kong air quality data with the respective standards and classification of pollution bands of the China Air Quality Index (AQI), the United Kingdom Daily AQI (DAQI), and the United States Environmental Protection Agency (USEPA) AQI. The mean concentrations of PM 10 and SO 2 based on maximum 3-h mean exceeded the WHO AQG by 37% and 50%, respectively. We identified the combined condition of observed high-pollution days as either at least one pollutant > 1.5×WHO AQG or at least two pollutants > 1.0�

Estimating representative background PM2.5 concentration in heavily polluted areas using baseline separation technique and chemical mass balance model

Science.gov (United States)

Gao, Shuang; Yang, Wen; Zhang, Hui; Sun, Yanling; Mao, Jian; Ma, Zhenxing; Cong, Zhiyuan; Zhang, Xian; Tian, Shasha; Azzi, Merched; Chen, Li; Bai, Zhipeng

2018-02-01

The determination of background concentration of PM2.5 is important to understand the contribution of local emission sources to total PM2.5 concentration. The purpose of this study was to exam the performance of baseline separation techniques to estimate PM2.5 background concentration. Five separation methods, which included recursive digital filters (Lyne-Hollick, one-parameter algorithm, and Boughton two-parameter algorithm), sliding interval and smoothed minima, were applied to one-year PM2.5 time-series data in two heavily polluted cities, Tianjin and Jinan. To obtain the proper filter parameters and recession constants for the separation techniques, we conducted regression analysis at a background site during the emission reduction period enforced by the Government for the 2014 Asia-Pacific Economic Cooperation (APEC) meeting in Beijing. Background concentrations in Tianjin and Jinan were then estimated by applying the determined filter parameters and recession constants. The chemical mass balance (CMB) model was also applied to ascertain the effectiveness of the new approach. Our results showed that the contribution of background PM concentration to ambient pollution was at a comparable level to the contribution obtained from the previous study. The best performance was achieved using the Boughton two-parameter algorithm. The background concentrations were estimated at (27 ± 2) μg/m3 for the whole year, (34 ± 4) μg/m3 for the heating period (winter), (21 ± 2) μg/m3 for the non-heating period (summer), and (25 ± 2) μg/m3 for the sandstorm period in Tianjin. The corresponding values in Jinan were (30 ± 3) μg/m3, (40 ± 4) μg/m3, (24 ± 5) μg/m3, and (26 ± 2) μg/m3, respectively. The study revealed that these baseline separation techniques are valid for estimating levels of PM2.5 air pollution, and that our proposed method has great potential for estimating the background level of other air pollutants.

Spatiotemporal mapping of ground water pollution in a Greek lignite basin, using geostatistics

Energy Technology Data Exchange (ETDEWEB)

Modis, K. [National Technical Univ. of Athens, Athens (Greece)

2010-07-01

An issue of significant interest in the mining industry in Greece is the occurrence of chemical pollutants in ground water. Ammonium, nitrites and nitrates concentrations have been monitored through an extensive sampling network in the Ptolemais lignite opencast mining area in Greece. Due to intensive mining efforts in the area, the surface topology is continuously altered, affecting the life span of the water boreholes and resulting in messy spatiotemporal distribution of data. This paper discussed the spatiotemporal mapping of ground water pollution in the Ptolemais lignite basin, using geostatistics. More specifically, the spatiotemporal distribution of ground water contamination was examined by the application of the bayesian maximum entropy theory which allows merging spatial and temporal estimations in a single model. The paper provided a description of the site and discussed the materials and methods, including samples and statistics; variography; and spatiotemporal mapping. It was concluded that in the case of the Ptolemais mining area, results revealed an underlying average yearly variation pattern of pollutant concentrations. Inspection of the produced spatiotemporal maps demonstrated a continuous increase in the risk of ammonium contamination, while risk for the other two pollutants appeared in hot spots. 18 refs., 1 tab., 7 figs.

Spatiotemporal mapping of ground water pollution in a Greek lignite basin, using geostatistics

International Nuclear Information System (INIS)

Modis, K.

2010-01-01

An issue of significant interest in the mining industry in Greece is the occurrence of chemical pollutants in ground water. Ammonium, nitrites and nitrates concentrations have been monitored through an extensive sampling network in the Ptolemais lignite opencast mining area in Greece. Due to intensive mining efforts in the area, the surface topology is continuously altered, affecting the life span of the water boreholes and resulting in messy spatiotemporal distribution of data. This paper discussed the spatiotemporal mapping of ground water pollution in the Ptolemais lignite basin, using geostatistics. More specifically, the spatiotemporal distribution of ground water contamination was examined by the application of the bayesian maximum entropy theory which allows merging spatial and temporal estimations in a single model. The paper provided a description of the site and discussed the materials and methods, including samples and statistics; variography; and spatiotemporal mapping. It was concluded that in the case of the Ptolemais mining area, results revealed an underlying average yearly variation pattern of pollutant concentrations. Inspection of the produced spatiotemporal maps demonstrated a continuous increase in the risk of ammonium contamination, while risk for the other two pollutants appeared in hot spots. 18 refs., 1 tab., 7 figs.

Field investigation of physical and chemical mechanisms affecting pollutant concentrations in fog droplets

Energy Technology Data Exchange (ETDEWEB)

Jacob, D.J.; Waldman, J.M.; Munger, J.W.; Hoffmann, M.R.

1984-09-01

High ionic loadings were found in fogwater collected at Bakersfield, California during an extended stagnation episode. The major ions were NH4(+), NO3(-), and SO4(2-), with concentrations usually in the millimolar range. Droplet growth played an important role in determining fogwater concentrations. The amount of solute decreased substantially over the course of each fog event this was attributed, at least in part, to deposition of fog droplets on surfaces. The occurrence of this was attributed, at least in part, to deposition of fog droplets on surfaces. The sulfate fraction in the aerosol increased appreciably over several days of stagnation, but no statistical evidence for in situ S(IV) aqueous-phase oxidation was found. The high ammonia concentrations present were sufficient to neutralize a large fraction of the ambient acidity. As a result, fogwater pH values rarely attained the extremely low values found in other polluted environments. 46 references.

The maximum reservoir capacity of soils for persistent organic pollutants: implications for global cycling

International Nuclear Information System (INIS)

Dalla Valle, M.; Jurado, E.; Dachs, J.; Sweetman, A.J.; Jones, K.C.

2005-01-01

The concept of maximum reservoir capacity (MRC), the ratio of the capacities of the surface soil and of the atmospheric mixed layer (AML) to hold chemical under equilibrium conditions, is applied to selected persistent organic pollutants (POPs) in the surface 'skin' (1 mm) of soils. MRC is calculated as a function of soil organic matter (SOM) content and temperature-dependent K OA and mapped globally for selected PCB congeners (PCB-28; -153; -180) and HCB, to identify regions with a higher tendency to retain POPs. It is shown to vary over many orders of magnitude, between compounds, locations and time (seasonally/diurnally). The MRC approach emphasises the very large capacity of soils as a storage compartment for POPs. The theoretical MRC concept is compared to reality and its implications for the global cycling of POPs are discussed. Sharp gradients in soil MRC can exist in mountainous areas and between the land and ocean. Exchanges between oceans and land masses via the atmosphere is likely to be an important driver to the global cycling of these compounds, and net ocean-land transfers could occur in some areas. - Major global terrestrial sinks/stores for POPs are identified and the significance of gradients between them discussed

The composition of pollutted air in Moscow based on surface observations

Science.gov (United States)

Pankratova, Natalia; Elansky, Nikolai; Skorokhod, Andrey

2013-04-01

Moscow is the one of the biggest world megacities. Population, industry, transport are strong sources of air pollution. This pollution influences on the air quality in the city and in the neighbor regions due to spreading by the wind. Here we present an analysis of variations of atmospheric compounds in Moscow since 2002 until the present in its dependence on different atmospheric characteristics, particularly cyclonic and anticyclonic conditions, heat waves and anthropogenic factors. The following variables are considered: NO2, NO, CO, CO2, O3, SO2, NMHC. The monitoring site is located at Moscow State University meteorological observatory on the South-West of Moscow. All observations are provided by A.M. Obukhov Institute of Atmospheric Physics RAS. Due to these continuous measurements, the typical (ore basic) level of pollution as well as the extreme cases have been studied. The temporal variability of the atmospheric compounds, and the chemical interaction of ozone and nitrogen oxides are investigated. High concentrations of nitrogen oxides are observed throughout the year. During some months the 90th NO2 percentile exceeds 60 ppb, NO - 80 ppb. Based on surface observations, we show that extremes of pollutant concentrations correspond with anticyclonic conditions and anthropogenic processes. These often increase the impact on the weather. These situations correspond with the anomalous cold winter in 2006 and heat wave in 2002. In these periods, concentrations of air pollutions exceed MAC, but the ozone concentration usually decreases due to interaction with NOx. Only two times, ozone concentration exceeded MAC - the heat waves 2002 and 2010. Also in the study we obtain the logarithmic dependence between ozone mix ratio and NO2/NO, which can be used for prediction of the surface ozone concentrations in Moscow: [O3] = 12.22Ln([NO2]/[NO]) + 15.3 However, this equation is not possible to use in smog conditions. From 29 July to 15 August Moscow was in a dense smoke

Equilibrium sampling of environmental pollutants in fish: comparison with lipid-normalized concentrations and homogenization effects on chemical activity.

Science.gov (United States)

Jahnke, Annika; Mayer, Philipp; Adolfsson-Erici, Margaretha; McLachlan, Michael S

2011-07-01

Equilibrium sampling of organic pollutants into the silicone polydimethylsiloxane (PDMS) has recently been applied in biological tissues including fish. Pollutant concentrations in PDMS can then be multiplied with lipid/PDMS distribution coefficients (D(Lipid,PDMS) ) to obtain concentrations in fish lipids. In the present study, PDMS thin films were used for equilibrium sampling of polychlorinated biphenyls (PCBs) in intact tissue of two eels and one salmon. A classical exhaustive extraction technique to determine lipid-normalized PCB concentrations, which assigns the body burden of the chemical to the lipid fraction of the fish, was additionally applied. Lipid-based PCB concentrations obtained by equilibrium sampling were 85 to 106% (Norwegian Atlantic salmon), 108 to 128% (Baltic Sea eel), and 51 to 83% (Finnish lake eel) of those determined using total extraction. This supports the validity of the equilibrium sampling technique, while at the same time confirming that the fugacity capacity of these lipid-rich tissues for PCBs was dominated by the lipid fraction. Equilibrium sampling was also applied to homogenates of the same fish tissues. The PCB concentrations in the PDMS were 1.2 to 2.0 times higher in the homogenates (statistically significant in 18 of 21 cases, p equilibrium sampling and partition coefficients determined using tissue homogenates. Copyright © 2011 SETAC.

A comparison of muscle activity in concentric and counter movement maximum bench press.

Science.gov (United States)

van den Tillaar, Roland; Ettema, Gertjan

2013-01-01

The purpose of this study was to compare the kinematics and muscle activation patterns of regular free-weight bench press (counter movement) with pure concentric lifts in the ascending phase of a successful one repetition maximum (1-RM) attempt in the bench press. Our aim was to evaluate if diminishing potentiation could be the cause of the sticking region. Since diminishing potentiation cannot occur in pure concentric lifts, the occurrence of a sticking region in this type of muscle actions would support the hypothesis that the sticking region is due to a poor mechanical position. Eleven male participants (age 21.9 ± 1.7 yrs, body mass 80.7 ± 10.9 kg, body height 1.79 ± 0.07 m) conducted 1-RM lifts in counter movement and in pure concentric bench presses in which kinematics and EMG activity were measured. In both conditions, a sticking region occurred. However, the start of the sticking region was different between the two bench presses. In addition, in four of six muscles, the muscle activity was higher in the counter movement bench press compared to the concentric one. Considering the findings of the muscle activity of six muscles during the maximal lifts it was concluded that the diminishing effect of force potentiation, which occurs in the counter movement bench press, in combination with a delayed muscle activation unlikely explains the existence of the sticking region in a 1-RM bench press. Most likely, the sticking region is the result of a poor mechanical force position.

CORRELATION BETWEEN PATHOLOGY AND EXCESS OF MAXIMUM CONCENTRATION LIMIT OF POLLUTANTS IN THE ENVIRONMENT OF THE REPUBLIC OF DAGESTAN

Directory of Open Access Journals (Sweden)

G. M. Abdurakhmanov

2013-01-01

Full Text Available Abstract. Statistical data from "Indicators of health status of the Republic of Dagestan" for 1999 - 2010 years are presented in the work. The aim of this work was to identify a cause-effect correlation between non-communicable diseases (ischemic heart disease, neuropsychiatric disease, endemic goiter, diabetes, congenital anomalies and environmental factors in the Republic of Dagestan.Statistical data processing was carried out using the software package Statistica, Microsoft Excel. The Spearman rank correlation coefficient (ρ was used for identify of correlation between indicators of environmental quality and health of population.Moderate positive correlation is observed between the development of pathology and excess of concentrations of contaminants in drinking water sources. Direct correlations are founded between development of the studied pathologies and excess of concentrations of heavy metals and their mobile forms in soils of the region. Direct correlation is found between excess of concentrations of heavy metals in the pasture vegetation (factorial character and the morbidity of the population (effective character.

The analysis of results received from the programme for calculating the concentration of pollutants from vehicles with internal combustion engines on the crossroads in urban environments

International Nuclear Information System (INIS)

Tashevski, Done; Dimitrovski, Mile

1995-01-01

The analysis of results and influence of specified factors on the concentration of pollutants on the crossroads with chosen characteristic conditions has been made, on the basis of the programme for calculating the concentration of pollutants from vehicles with internal combustion engines on the crossroads in urban environments. (author)

Pollutant Flux Estimation in an Estuary Comparison between Model and Field Measurements

Directory of Open Access Journals (Sweden)

Yen-Chang Chen

2014-08-01

Full Text Available This study proposes a framework for estimating pollutant flux in an estuary. An efficient method is applied to estimate the flux of pollutants in an estuary. A gauging station network in the Danshui River estuary is established to measure the data of water quality and discharge based on the efficient method. A boat mounted with an acoustic Doppler profiler (ADP traverses the river along a preselected path that is normal to the streamflow to measure the velocities, water depths and water quality for calculating pollutant flux. To know the characteristics of the estuary and to provide the basis for the pollutant flux estimation model, data of complete tidal cycles is collected. The discharge estimation model applies the maximum velocity and water level to estimate mean velocity and cross-sectional area, respectively. Thus, the pollutant flux of the estuary can be easily computed as the product of the mean velocity, cross-sectional area and pollutant concentration. The good agreement between the observed and estimated pollutant flux of the Danshui River estuary shows that the pollutant measured by the conventional and the efficient methods are not fundamentally different. The proposed method is cost-effective and reliable. It can be used to estimate pollutant flux in an estuary accurately and efficiently.

Response of soil microbial communities to roxarsone pollution along a concentration gradient.

Science.gov (United States)

Liu, Yaci; Zhang, Zhaoji; Li, Yasong; Wen, Yi; Fei, Yuhong

2017-07-29

The extensive use of roxarsone (3-nitro-4-hydroxyphenylarsonic acid) as a feed additive in the broiler poultry industry can lead to environmental arsenic contamination. This study was conducted to reveal the response of soil microbial communities to roxarsone pollution along a concentration gradient. To explore the degradation process and degradation kinetics of roxarsone concentration gradients in soil, the concentration shift of roxarsone at initial concentrations of 0, 50, 100, and 200 mg/kg, as well as that of the arsenic derivatives, was detected. The soil microbial community composition and structure accompanying roxarsone degradation were investigated by high-throughput sequencing. The results showed that roxarsone degradation was inhibited by a biological inhibitor, confirming that soil microbes were absolutely essential to its degradation. Moreover, soil microbes had considerable potential to degrade roxarsone, as a high initial concentration of roxarsone resulted in a substantially increased degradation rate. The concentrations of the degradation products HAPA (3-amino-4-hydroxyphenylarsonic acid), AS(III), and AS(V) in soils were significantly positively correlated. The soil microbial community composition and structure changed significantly across the roxarsone contamination gradient, and the addition of roxarsone decreased the microbial diversity. Some bacteria tended to be inhibited by roxarsone, while Bacillus, Paenibacillus, Arthrobacter, Lysobacter, and Alkaliphilus played important roles in roxarsone degradation. Moreover, HAPA, AS(III), and AS(V) were significantly positively correlated with Symbiobacterium, which dominated soils containing roxarsone, and their abundance increased with increasing initial roxarsone concentration. Accordingly, Symbiobacterium could serve as indicator of arsenic derivatives released by roxarsone as well as the initial roxarsone concentration. This is the first investigation of microbes closely related to roxarsone

Comparison of Land-Use Regression Modeling with Dispersion and Chemistry Transport Modeling to Assign Air Pollution Concentrations within the Ruhr Area

Directory of Open Access Journals (Sweden)

Frauke Hennig

2016-03-01

Full Text Available Two commonly used models to assess air pollution concentration for investigating health effects of air pollution in epidemiological studies are Land Use Regression (LUR models and Dispersion and Chemistry Transport Models (DCTM. Both modeling approaches have been applied in the Ruhr area, Germany, a location where multiple cohort studies are being conducted. Application of these different modelling approaches leads to differences in exposure estimation and interpretation due to the specific characteristics of each model. We aimed to compare both model approaches by means of their respective aims, modeling characteristics, validation, temporal and spatial resolution, and agreement of residential exposure estimation, referring to the air pollutants PM2.5, PM10, and NO2. Residential exposure referred to air pollution exposure at residences of participants of the Heinz Nixdorf Recall Study, located in the Ruhr area. The point-specific ESCAPE (European Study of Cohorts on Air Pollution Effects-LUR aims to temporally estimate stable long-term exposure to local, mostly traffic-related air pollution with respect to very small-scale spatial variations (≤100 m. In contrast, the EURAD (European Air Pollution Dispersion-CTM aims to estimate a time-varying average air pollutant concentration in a small area (i.e., 1 km2, taking into account a range of major sources, e.g., traffic, industry, meteorological conditions, and transport. Overall agreement between EURAD-CTM and ESCAPE-LUR was weak to moderate on a residential basis. Restricting EURAD-CTM to sources of local traffic only, respective agreement was good. The possibility of combining the strengths of both applications will be the next step to enhance exposure assessment.

Implications of alternative assumptions regarding future air pollution control in scenarios similar to the Representative Concentration Pathways

NARCIS (Netherlands)

Chuwah, C.; van Noije, T.; van Vuuren, D.P.; Hazeleger, W.; Strunk, A.; Deetman, S.; Beltran, A.M.; van Vliet, J.

2013-01-01

The uncertain, future development of emissions of short-lived trace gases and aerosols forms a key factor for future air quality and climate forcing. The Representative Concentration Pathways (RCPs) only explore part of this range as they all assume that worldwide ambitious air pollution control

Influence of avenue-trees on air quality at the urban neighborhood scale. Part II: traffic pollutant concentrations at pedestrian level.

Science.gov (United States)

Gromke, Christof; Blocken, Bert

2015-01-01

Flow and dispersion of traffic-emitted pollutants were studied in a generic urban neighborhood for various avenue-tree layouts by employing 3D steady RANS simulations with the realizable k-ε turbulence model. In comparison to the tree-free situation quantitative and qualitative changes with flow reversal in the wind field were observed. Low to moderate increases (pollutant concentration were found at pedestrian level. An approximately 1% increase in the neighborhood-averaged concentration was obtained with each percent of the street canyon volumes being occupied by vegetation for occupation fractions between 4 and 14%. The overall pattern of concentration changes relative to the tree-free situation was similar for all avenue-tree layouts. However, pronounced locally restricted decreases or increases in concentration (-87 to +1378%) occurred. The results indicate the necessity to account for existing or planned avenue-trees in neighborhood scaled is dispersion studies. Their consideration is prerequisite for reliable urban air quality assessment.

Characterization of particle number concentrations and PM2.5 in a school: influence of outdoor air pollution on indoor air.

Science.gov (United States)

Guo, Hai; Morawska, Lidia; He, Congrong; Zhang, Yanli L; Ayoko, Godwin; Cao, Min

2010-07-01

The impact of air pollution on school children's health is currently one of the key foci of international and national agencies. Of particular concern are ultrafine particles which are emitted in large quantities, contain large concentrations of toxins and are deposited deeply in the respiratory tract. In this study, an intensive sampling campaign of indoor and outdoor airborne particulate matter was carried out in a primary school in February 2006 to investigate indoor and outdoor particle number (PN) and mass concentrations (PM(2.5)), and particle size distribution, and to evaluate the influence of outdoor air pollution on the indoor air. For outdoor PN and PM(2.5), early morning and late afternoon peaks were observed on weekdays, which are consistent with traffic rush hours, indicating the predominant effect of vehicular emissions. However, the temporal variations of outdoor PM(2.5) and PN concentrations occasionally showed extremely high peaks, mainly due to human activities such as cigarette smoking and the operation of mower near the sampling site. The indoor PM(2.5) level was mainly affected by the outdoor PM(2.5) (r = 0.68, p changes to the modal structure of particle number and size distribution, even though the I/O ratio was different for different size classes. The I/O curves had a maximum value for particles with diameters of 100-400 nm under both occupied and unoccupied scenarios, whereas no significant difference in I/O ratio for PM(2.5) was observed between occupied and unoccupied conditions. Inspection of the size-resolved I/O ratios in the preschool centre and the classroom suggested that the I/O ratio in the preschool centre was the highest for accumulation mode particles at 600 nm after school hours, whereas the average I/O ratios of both nucleation mode and accumulation mode particles in the classroom were much lower than those of Aitken mode particles. The findings obtained in this study are useful for epidemiological studies to estimate the

Air pollution in southern Africa: The case of motor vehicle exhaust contribution in Dar Es Salaam city

International Nuclear Information System (INIS)

Jackson, M.M.

2005-01-01

The aim of this study was to review air pollution problems in the Southern Africa region and establish the quality of ambient air in Dar Es Salaam city in Tanzania with respect to three vehicular pollutants which are sulphur dioxide (SO 2 ), nitrogen dioxide (NO 2 ) and suspended particulate matters (SPM). These pollutants were measured in eight different locations in Dar-Es Salaam city which are Fire, Morocco, Tazara, Kariakoo, Ubungo, Posta, UCLAS, and Akiba. With the exception of South Africa and Botswana, other countries in the Southern Africa Region which include Tanzania, Mozambique, Malawi. Zambia, Zimbabwe. Angola and Namibia do not have air pollution standards, and regular air pollution monitoring is not carried out in these countries. Diesel fueled vehicles in South Africa are responsible for one third of all smog-forming nitrogen dioxides and almost two-thirds of all particulate pollution emitted by all vehicles. The measurement methods used in Dar Es Salaam study were pararosaniline method for SO 2 , Saltzman for measuring nitrogen dioxide, and filtration method for suspended particulate matters. The following was observed from the analysis: Hourly sulphur dioxide concentration ranged from 558 -1385 μg/m 3 . These measured values were above the recommended WHO guidelines with an hourly objective value of 350 μg/m 3 . Hourly nitrogen dioxide concentration was found to range from 18 to 53 μg/m 3 . The maximum hourly nitrogen dioxide concentration at 53 μg/m 3 was below the recommended WHO guidelines with a value of 200 μg/m 3 . The hourly suspended particulate matter (SPM) was found to range from 744 to 1161 μg/m 3 . The measured suspended particulate matter concentrations were above the recommended hourly maximum value by WHO guidelines which is 230μg/m 3 . The correlation coefficient of pollutants and the number of vehicles counted for different sampling points was determined and found to be fair reasonable with a value of 0.906 for suspended

Enhanced photocatalytic degradation of pollutants in petroleum refinery wastewater under mild conditions

International Nuclear Information System (INIS)

Saien, J.; Nejati, H.

2007-01-01

A circulating photocatalytic reactor was used for removing aliphatic and aromatic organic pollutants in refinery wastewater. The TiO 2 added wastewater samples, while saturating with air, were irradiated with an immersed mercury UV lamp (400 W, 200-550 nm). Optimal catalyst concentration, fluid pH and temperature were obtained at amounts of near 100 mg L -1 , 3 and 318 K, respectively. A maximum reduction in chemical oxygen demand of more than 90% was achieved after about 4 h irradiation and hence, 73% after about only 90 min; significant pollutant removal was also achievable in the other conditions. The identification of the organic pollutants, provided by means of a GC/MS and a GC analysis systems, equipped with headspace injection technique, showed that the major compounds were different fractions of petroleum aliphatic hydrocarbons (up to C 10 ) and the well-known aromatic compounds such as benzene, toluene and ethylbenzene. The results showed a high efficiency degradation of all of these pollutants

Enhanced photocatalytic degradation of pollutants in petroleum refinery wastewater under mild conditions

Energy Technology Data Exchange (ETDEWEB)

Saien, J. [Department of Applied Chemistry, University of Bu-Ali Sina, Hamadan 65174 (Iran, Islamic Republic of)], E-mail: saien@basu.ac.ir; Nejati, H. [Department of Applied Chemistry, University of Bu-Ali Sina, Hamadan 65174 (Iran, Islamic Republic of)

2007-09-05

A circulating photocatalytic reactor was used for removing aliphatic and aromatic organic pollutants in refinery wastewater. The TiO{sub 2} added wastewater samples, while saturating with air, were irradiated with an immersed mercury UV lamp (400 W, 200-550 nm). Optimal catalyst concentration, fluid pH and temperature were obtained at amounts of near 100 mg L{sup -1}, 3 and 318 K, respectively. A maximum reduction in chemical oxygen demand of more than 90% was achieved after about 4 h irradiation and hence, 73% after about only 90 min; significant pollutant removal was also achievable in the other conditions. The identification of the organic pollutants, provided by means of a GC/MS and a GC analysis systems, equipped with headspace injection technique, showed that the major compounds were different fractions of petroleum aliphatic hydrocarbons (up to C{sub 10}) and the well-known aromatic compounds such as benzene, toluene and ethylbenzene. The results showed a high efficiency degradation of all of these pollutants.

Environmental Monitoring, Water Quality - Total Maximum Daily Load (TMDL)

Data.gov (United States)

NSGIC Education | GIS Inventory — The Clean Water Act Section 303(d) establishes the Total Maximum Daily Load (TMDL) program. The purpose of the TMDL program is to identify sources of pollution and...

Simulation of trace metals and PAH atmospheric pollution over Greater Paris: Concentrations and deposition on urban surfaces

Science.gov (United States)

Thouron, L.; Seigneur, C.; Kim, Y.; Legorgeu, C.; Roustan, Y.; Bruge, B.

2017-10-01

Urban areas can be subject not only to poor air quality, but also to contamination of other environmental media by air pollutants. Here, we address the potential transfer of selected air pollutants (two metals and three PAH) to urban surfaces. To that end, we simulate meteorology and air pollution from Europe to a Paris suburban neighborhood, using a four-level one-way nesting approach. The meteorological and air quality simulations use urban canopy sub-models in order to better represent the effect of the urban morphology on the air flow, atmospheric dispersion, and deposition of air pollutants to urban surfaces. This modeling approach allows us to distinguish air pollutant deposition among various urban surfaces (roofs, roads, and walls). Meteorological model performance is satisfactory, showing improved results compared to earlier simulations, although precipitation amounts are underestimated. Concentration simulation results are also satisfactory for both metals, with a fractional bias Paris region. The model simulation results suggest that both wet and dry deposition processes need to be considered when estimating the transfer of air pollutants to other environmental media. Dry deposition fluxes to various urban surfaces are mostly uniform for PAH, which are entirely present in fine particles. However, there is significantly less wall deposition compared to deposition to roofs and roads for trace metals, due to their coarse fraction. Meteorology, particle size distribution, and urban morphology are all important factors affecting air pollutant deposition. Future work should focus on the collection of data suitable to evaluate the performance of atmospheric models for both wet and dry deposition with fine spatial resolution.

Pollutant threshold concentration determination in marine ecosystems using an ecological interaction endpoint.

Science.gov (United States)

Wang, Changyou; Liang, Shengkang; Guo, Wenting; Yu, Hua; Xing, Wenhui

2015-09-01

The threshold concentrations of pollutants are determined by extrapolating single-species effect data to community-level effects. This assumes the most sensitive endpoint of the life cycle of individuals and the species sensitivity distribution from single-species toxic effect tests, thus, ignoring the ecological interactions. The uncertainties due to this extrapolation can be partially overcome using the equilibrium point of a customized ecosystem. This method incorporates ecological interactions and integrates the effects on growth, survival, and ingestion into a single effect measure, the equilibrium point excursion in the customized ecosystem, in order to describe the toxic effects on plankton. A case study showed that the threshold concentration of copper calculated with the endpoint of the equilibrium point was 10 μg L(-1), which is significantly different from the threshold calculated with a single-species endpoint. The endpoint calculated using this method provides a more relevant measure of the ecological impact than any single individual-level endpoint. Copyright © 2015 Elsevier Ltd. All rights reserved.

Air quality more extensive monitoring of particulates pollution but concentrations must be reduced by 2005

International Nuclear Information System (INIS)

Ba, M.; Colosio, J.

2000-09-01

Most epidemiological data point to a link between the concentrations of particles measured in the ambient air and the effects of air pollution on human health. Particulates emitted by road traffic and industry are among the most harmful; they carry serious risks. The particulate monitoring network and legislation on the issue are constantly changing. In France, the number of monitoring stations has more than doubled in recent years. EC Directive 1999/30/EC of 22 April 1999 sets limit values for concentrations of particulates in ambient air to be complied with at certain given dates. In France, while the concentrations measured in urban areas with over 100 000 inhabitants are below the limit values set by the Directive for today, they are significantly higher than those to be complied with by 1 January 2005. (author)

Assessment of Marine Pollution in İzmir Bay: Heavy Metal and Organic Compound Concentrations in Surficial Sediments

OpenAIRE

AKSU, Ali Engin

2014-01-01

The extent of marine pollution in İzmir Bay is investigated using inorganic and organic geochemical data from surface sediments. The concentrations of 42 elements in 84 samples established that surface sediments in Inner İzmir Bay display significant enrichments in Ag, As, Cd, Cr, Cu, Hg, Mo, P, Pb, Sb, Sn, V, and Zn, associated with notably high concentrations of total organic carbon and sulphur. Organic geochemical data in 14 samples from Inner İzmir Bay showed that these sediments...

Combining tree-ring metal concentrations and lead, carbon and oxygen isotopes to reconstruct peri-urban atmospheric pollution

Directory of Open Access Journals (Sweden)

Annick Doucet

2012-08-01

Full Text Available In this study, we analysed the tree-ring metal concentrations and isotope ratios of five stands located in three contrasted settings to infer the diffuse air pollution history of the northern part of the Windsor–Québec City Corridor in eastern Canada. Tree-ring series show that the Cd and Zn accumulation rates were higher between 1960 and 1986 and that the long-term acidification of the soil (Ca/Al series was likely induced by NOx and SOx deposition (δ15N and δ13C trends as proxy. The Pb concentrations and 206Pb/207Pb ratios indicate that the dominant source of lead from 1880 to the 1920s was the combustion of north-eastern American coal, which was succeeded by the combustion of leaded gasoline from the 1920s to the end of the 1980s. Our modelling approach allows separating the climatic and anthropogenic effects on the tree-ring δ13C and δ18O responses. Diffuse air pollution caused an enrichment in 13C in all stands and a decrease of the δ18O values only in three of the stands. This study indicates that dendrogeochemistry can show contrasted responses to environmental changes and that the combination of several independent indicators constitutes a powerful tool to reconstruct the air pollution history in the complex context of peri-urban regions.

Medical aspects of atmosphere pollution in Tbilisi, Georgia.

Science.gov (United States)

Lagidze, Lamzira; Matchavariani, Lia; Tsivtsivadze, Nodar; Khidasheli, Nargiz; Paichadze, Nino; Motsonelidze, Nargiz; Vakhtangishvili, Maia

2015-01-01

Climate change and its impact on ecosystems is one of the main problem of 21st century. Increase in green house gas in the atmosphere was regarded as an important cause. Atmospheric composition had significantly changed due to intensive technogenic pollution. Increase in aerosol (solid, liquid and gas) concentration had serious impact on human health and raised the level of risk factors for longevity of life. Despite, global character of climatic change and its intensity in numerous ways was influenced by local specificity of regions, their geographical location and meteorological factors. A study on the atmospheric quality (quantitative and percentage estimation of aerosols) of Georgia was carried out. Also the assessment of impact of meteorological and ecological conditions on human health was made for Tbilisi city. A relation between contaminants and meteorological factors was evaluated, particularly gas pollutants were strongly correlated with each other due to their photochemical activity; positive correlation (0.65; 0.69) between air temperature and pollutants. All the contaminants showed negative correlation with relative humidity, due to hydrolyzing ability. On the basis of multi-factorial statistical analysis, correlation between ambulance call, weather type, atmosphere pollution index, change in ground ozone quantity and earth magnetic field were determined. Atmospheric pollution due to dust, carbon, sulfur and nitrogen oxides, ground ozone quantity in Tbilisi significantly exceeded maximum permissible level, that effected human health.

Healthy neighborhoods: walkability and air pollution.

Science.gov (United States)

Marshall, Julian D; Brauer, Michael; Frank, Lawrence D

2009-11-01

The built environment may influence health in part through the promotion of physical activity and exposure to pollution. To date, no studies have explored interactions between neighborhood walkability and air pollution exposure. We estimated concentrations of nitric oxide (NO), a marker for direct vehicle emissions), and ozone (O(3)) and a neighborhood walkability score, for 49,702 (89% of total) postal codes in Vancouver, British Columbia, Canada. NO concentrations were estimated from a land-use regression model, O(3) was estimated from ambient monitoring data; walkability was calculated based on geographic attributes such as land-use mix, street connectivity, and residential density. All three attributes exhibit an urban-rural gradient, with high walkability and NO concentrations, and low O(3) concentrations, near the city center. Lower-income areas tend to have higher NO concentrations and walkability and lower O(3) concentrations. Higher-income areas tend to have lower pollution (NO and O(3)). "Sweet-spot" neighborhoods (low pollution, high walkability) are generally located near but not at the city center and are almost exclusively higher income. Increased concentration of activities in urban settings yields both health costs and benefits. Our research identifies neighborhoods that do especially well (and especially poorly) for walkability and air pollution exposure. Work is needed to ensure that the poor do not bear an undue burden of urban air pollution and that neighborhoods designed for walking, bicycling, or mass transit do not adversely affect resident's exposure to air pollution. Analyses presented here could be replicated in other cities and tracked over time to better understand interactions among neighborhood walkability, air pollution exposure, and income level.

[Problems and ways of solutions to harmonize standards for air pollution].

Science.gov (United States)

Avaliani, S L; Novikov, S M; Shashina, T A; Skvortsova, N S; Kislitsin, V A; Mishina, A L

2012-01-01

In the article the basic problems of harmonization of domestic regulatory framework of air pollution with the WHO recommendations and normative values adopted in the EU, U.S. and other countries are considered. The important role of health risk analysis methodology in the process of harmonization of regulation and control of air quality has been pointed out. The necessity of radical changes in the structure and content of the basic normative document GN 2.1.6.1338-03 "maximum permissible concentration (MPC) of pollutants in the air of populated areas" has been shown. The algorithm of the procedure that justifies the new list of normative values in the air harmonized with international recommendations and standards of developed countries has been proposed.

Ecological risk evaluation of polluted soils from Sasa mineral processing concentrator

OpenAIRE

Krstev, Boris; Golomeov, Blagoj; Golomeova, Mirjana; Krstev, Aleksandar

2007-01-01

The idea that the earth is a closed system and that soil, like other mediums, is polluted by human activities, is very recent, hardly thirty years old. The chief preoccupation has been with water pollution, a conviction that, sooner or later, all the pollutants found in water were the principal cause of the emergence of aquatic ecotoxicology. Yet, the existence of polluted soils has been cited since ancient times. Greek and Roman writers remarked that the contamination of water and air near m...

The Multimedia Environmental Pollutant Assessment System (MEPAS)reg-sign: Atmospheric pathway formulations. Revision

International Nuclear Information System (INIS)

Droppo, J.G.; Buck, J.W.

1996-03-01

The Multimedia Environmental Pollutant Assessment System (MEPAS) is an integrated software implementation of physics-based fate and transport models for health and environmental risk assessments of both radioactive and hazardous pollutants. This atmospheric component report is one of a series of formulation reports that document the MEPAS mathematical models. MEPAS is a multimedia model; pollutant transport is modeled within, through, and between multiple media (air, soil, groundwater, and surface water). The estimated concentrations in the various media are used to compute exposures and impacts to the environment, to maximum individuals, and to populations. The MEPAS atmospheric component for the air media documented in this report includes models for emission from a source to the air, initial plume rise and dispersion, airborne pollutant transport and dispersion, and deposition to soils and crops. The material in this report is documentation for MEPAS Versions 3.0 and 3.1 and the MEPAS version used in the Remedial Action Assessment System (RAAS) Version 1.0

Low concentrations of persistent organic pollutants (POPs) in air at Cape Verde.

Science.gov (United States)

Nøst, Therese Haugdahl; Halse, Anne Karine; Schlabach, Martin; Bäcklund, Are; Eckhardt, Sabine; Breivik, Knut

2018-01-15

Ambient air is a core medium for monitoring of persistent organic pollutants (POPs) under the Stockholm Convention and is used in studies of global transports of POPs and their atmospheric sources and source regions. Still, data based on active air sampling remain scarce in many regions. The primary objectives of this study were to (i) monitor concentrations of selected POPs in air outside West Africa, and (ii) to evaluate potential atmospheric processes and source regions affecting measured concentrations. For this purpose, an active high-volume air sampler was installed on the Cape Verde Atmospheric Observatory at Cape Verde outside the coast of West Africa. Sampling commenced in May 2012 and 43 samples (24h sampling) were collected until June 2013. The samples were analyzed for selected polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs), hexachlorobenzene (HCB) and chlordanes. The concentrations of these POPs at Cape Verde were generally low and comparable to remote sites in the Arctic for several compounds. Seasonal trends varied between compounds and concentrations exhibited strong temperature dependence for chlordanes. Our results indicate net volatilization from the Atlantic Ocean north of Cape Verde as sources of these POPs. Air mass back trajectories demonstrated that air masses measured at Cape Verde were generally transported from the Atlantic Ocean or the North African continent. Overall, the low concentrations in air at Cape Verde were likely explained by absence of major emissions in areas from which the air masses originated combined with depletion during long-range atmospheric transport due to enhanced degradation under tropical conditions (high temperatures and concentrations of hydroxyl radicals). Copyright © 2017 The Author(s). Published by Elsevier B.V. All rights reserved.

Analysis of Co, Cr and Mn Concentrations in Atmospheric Dry Deposition in Hamadan City

Directory of Open Access Journals (Sweden)

P. Shokri Ragheb

2016-07-01

Full Text Available Introduction & Objective: Heavy metals are major pollutants that can spread in the atmosphere with particulate matter and dust and because of the toxic and carcinogenic effects, their meas-urement and control is very important. Therefore, this study was conducted to assess Co, Cr and Mn concentration in the atmospheric dry deposition collected from Hamadan city in 2014. Materials & Methods: After collection of 12 dust samples from 3 sampling stations and their laboratory preparation, metals concentrations were determined using ICP–OES. All statistical analyses were performed using the SPSS statistical package. Results: The results showed that the minimum and maximum mean concentrations of Co were 0.19 and 0.29 mg/kg for high and low traffic intensity sampling stations, respectively. The min and max mean concentrations of Cr were 0.65and 1.02 mg/kg for high traffic intensity and suburb sampling stations, respectively and the min and max mean concentrations of Mn were 7.23and 8.82 mg/kg for high and low traffic intensity sampling stations , respectively. Also comparing the mean concentrations of assessed metals with WHO permissible limits showed a significant difference (P< 0.05. The mean concentrations of metals were signifi-cantly lower than the maximum permissible limits. Conclusion: Although the mean concentrations of Co, Cr and Mn are lower than the standard levels, lack of continuous monitoring of heavy metals concentrations in the dust and particu-late matters in the air can lead to the entrance of various types of toxic pollutants such as heavy metals into the air and result in adverse health effects. (Sci J Hamadan Univ Med Sci 2016; 23 (2:149-156

[Output characteristics of rainfall runoff phosphorus pollution from a typical small watershed in Yimeng mountainous area].

Science.gov (United States)

Yu, Xing-xiu; Li, Zhen-wei; Liu, Qian-jin; Jing, Guang-hua

2012-08-01

Relationships between phosphorus pollutant concentrations and precipitation-runoff were analyzed by monitoring pollutant losses at outlets of the Menglianggu watershed in 2010. A typical small watershed was selected to examine the runoff and quality parameters such as total phosphorus (TP), particle phosphorus (PP), dissolve phosphorus (DP) and dissolve inorganic phosphorus (DIP) in rainfall-runoff of 10 rainfall events. Precipitation was above 2 mm for all the 10 rainfall events. The results showed that the peak of phosphorus concentrations occurred before the peak of water flows, whereas change processes of the phosphorus fluxes were consistent with that of the water flows and the phosphorus flux also have a strong linear relationship with the water flows. The minimums of the phosphorus concentrations in every 10 natural rainfall events have small differences with each other, but the maximum and EMCs of the phosphorus concentrations have significant differences with each rainfall event. This was mainly influenced by the precipitation, maximum rainfall intensity and mean rainfall intensity (EMCs) and was less influenced by rainfall duration. DP and TP were mainly composed of DIP and PP, respectively. There were no significant correlations between DIP/DP dynamic changes and rainfall characteristics, whereas significant correlations between PP/TP dynamic changes and maximum rainfall intensity were detected. The production of DIP, DP, AND TP were mainly influenced by the direct runoff (DR) and base flow (BF). The EMCs of DIP, DP, TP and the variations of DIP/DP were all found to have significant polynomial relationships with DR/TR., but the dynamic changes of PP/ TP and the EMCS of PP were less influenced by the DR/TR.

Concentrations of PAHs (Polycyclicaromatic Hydrocarbons Pollutant in Sediment of The Banten Bay

Directory of Open Access Journals (Sweden)

Khozanah Munawir

2018-02-01

Full Text Available Banten Bay is end of stream for a few rivers from Banten mainland where many manufactures and petrochemical industries are built. This may give environmental pressure of water quality of the bay due to pollutant input, such as Polycyclic Aromatic Hydrocarbons (PAHs. This study is to identify those pollutants and determine their total concentration and distribution in sediments. Surface sediment samples were collected in four zones: inner coastline within the bay, middle bay, coastline off the bay and outer of the Bay in April 2016. PAH components were extracted and measured using a gas chromatography-mass spectrometry. Levels of total PAHs in sediments in inner coastline within the bay ranged between 0.381-2.654 ppm with an average of 1.288 ppm, middle of the bay ranged between 0.747-1.762 ppm with an average of 1.198 ppm, outer of the bay ranged between 0.192-1.394 ppm with an average of 0.921 ppm, and east coast of the bay ranged between 0.191-1.394 ppm and an average of 0.778 ppm. The levels of total PAH contamination is apparently lower than those of PAH threshold in sediments (i.e. 4.5 ppm. Keywords: PAHs (Polycyclic Aromatic Hydrocarbons, Banten Bay

Photochemical and other pollution in South Holland

Energy Technology Data Exchange (ETDEWEB)

Posthumus, A.C.

1976-01-01

At the same 15 places as in 1974, regularly distributed over the industrial area west of Rotterdam, indicator plants for air pollution were set out in the open and were cultivated by the same standard method. Tulip and gladiolus were used as indicators for HF, during spring and summer, respectively. Both indicated that the same two sites, at Vlaardingen and Spijkenisse, had maximum HF concentration. In general, the mean leaf-tip injury at all sites was somewhat heavier than in 1974. Lucerne, as an indicator for SO2, sometimes showed more injury north of the New Waterway than south of it in June. Spinach, an indicator for O3/SO2, showed maximum injury in three different periods in June, July and mostly in August. The frequency and the measure of the injury to tobacco Bel W3 by O3 was maximum during some periods in August and September, the mean injury being heavier than in 1974. Urtica urens and Poa annua too, indicator plants for photochemical air pollution by peroxyacetyl nitrate and O3, showed more frequent injury in 1975, specially in some weeks in June and most of it in August. Petunia too indicated more influence of ethylene than in 1974, mostly in the second half of June. This year again the effect of air pollution on growth and yield of tulip Blue Parrot, tobacco Bel W3 and tomato extase plants was studied at the same six sites as last year by the mouth of the Rhine, with filtered and unfiltered greenhouses. Tulips in the unfiltered greenhouses showed a heavier leaf injury than those in the filtered greenhouses, except at the site in The Hague. These injured plants had a significantly lower average fresh and dry weight of the stems and leaves and of the bulbs too. Tobacco and tomato plants had a higher average dry weight of stems and leaves in the filtered greenhouses than in the unfiltered ones.

Pollutant threshold concentration determination in marine ecosystems using an ecological interaction endpoint

International Nuclear Information System (INIS)

Wang, Changyou; Liang, Shengkang; Guo, Wenting; Yu, Hua; Xing, Wenhui

2015-01-01

The threshold concentrations of pollutants are determined by extrapolating single-species effect data to community-level effects. This assumes the most sensitive endpoint of the life cycle of individuals and the species sensitivity distribution from single-species toxic effect tests, thus, ignoring the ecological interactions. The uncertainties due to this extrapolation can be partially overcome using the equilibrium point of a customized ecosystem. This method incorporates ecological interactions and integrates the effects on growth, survival, and ingestion into a single effect measure, the equilibrium point excursion in the customized ecosystem, in order to describe the toxic effects on plankton. A case study showed that the threshold concentration of copper calculated with the endpoint of the equilibrium point was 10 μg L −1 , which is significantly different from the threshold calculated with a single-species endpoint. The endpoint calculated using this method provides a more relevant measure of the ecological impact than any single individual-level endpoint. - Highlights: • Ecotoxicological effect of exposure to copper was tested on a customized ecosystem. • Equilibrium point of biomasses in the customized ecosystem was used as an endpoint. • Exposure–response relationship in a community level was built on equilibrium point. • A threshold concentration incorporating ecological interactions was derived. - The equilibrium biomass incorporating ecological interactions in a customized ecosystem was used as an endpoint to calculate the threshold concentration at a community level

Air pollution forecast in cities by an air pollution index highly correlated with meteorological variables

International Nuclear Information System (INIS)

Cogliani, E.

2001-01-01

There are many different air pollution indexes which represent the global urban air pollution situation. The daily index studied here is also highly correlated with meteorological variables and this index is capable of identifying those variables that significantly affect the air pollution. The index is connected with attention levels of NO 2 , CO and O 3 concentrations. The attention levels are fixed by a law proposed by the Italian Ministries of Health and Environment. The relation of that index with some meteorological variables is analysed by the linear multiple partial correlation statistical method. Florence, Milan and Vicence were selected to show the correlation among the air pollution index and the daily thermic excursion, the previous day's air pollution index and the wind speed. During the January-March period the correlation coefficient reaches 0.85 at Milan. The deterministic methods of forecasting air pollution concentrations show very high evaluation errors and are applied on limited areas around the observation stations, as opposed to the whole urban areas. The global air pollution, instead of the concentrations at specific observation stations, allows the evaluation of the level of the sanitary risk regarding the whole urban population. (Author)

What Causes Haze Pollution? An Empirical Study of PM2.5 Concentrations in Chinese Cities

Directory of Open Access Journals (Sweden)

Jiannan Wu

2016-01-01

Full Text Available In recent years, many areas of China have suffered from serious haze pollution, which greatly affects human health and daily life. It is of policy importance to understand the factors that influence the spatial concentration of PM2.5. Based on data from 74 cities with PM2.5 monitoring stations in 2013 and 2014, this study presents the overall haze situation in China and explores the determinants of PM2.5 using a random-effects model, as well as a set of OLS regressions. The results indicate that PM2.5 is significantly correlated with the industrial proportion, the number of motor vehicles, and household gas consumption, while public financial expenditure on energy saving and environmental protection does not show statistically significant effects. The analysis implies that China should adjust its economic structure and optimizes environmental governance to effectively respond to haze pollution.

Response of epiphytic lichen communities to decreasing ammonia air concentrations in a moderately polluted area of The Netherlands

International Nuclear Information System (INIS)

Sparrius, Laurens B.

2007-01-01

Decreasing local ammonia air concentrations in a moderately polluted area in The Netherlands were accompanied by a rapid increase in nitrogen-sensitive species (acidophytes) and a decline of nitrogen-tolerant macrolichens (nitrophytes). This paper presents data on the relationship between nitrophyte abundance and species abundance for three ecological groups of epiphytic lichens: nitrophytes (positively correlated with ammonia), acidophytes (negatively correlated) and neutrophytes (which have an optimum at medium concentrations) and suggests ammonia dependent optimum curves for these groups. In this study neutrophytes were found to die-off massively at sites with a decrease of the ammonia air concentration over the period 1996-2003. - Lichens can be used to detect both increasing and decreasing ammonia air concentrations

A Modeling Investigation of Human Exposure to Select Traffic-Related Air Pollutants in the Tampa Area: Spatiotemporal Distributions of Concentrations, Social Distributions of Exposures, and Impacts of Urban Design on Both

Science.gov (United States)

Yu, Haofei

Increasing vehicle dependence in the United States has resulted in substantial emissions of traffic-related air pollutants that contribute to the deterioration of urban air quality. Exposure to urban air pollutants trigger a number of public health concerns, including the potential of inequality of exposures and health effects among population subgroups. To better understand the impact of traffic-related pollutants on air quality, exposure, and exposure inequality, modeling methods that can appropriately characterize the spatiotemporally resolved concentration distributions of traffic-related pollutants need to be improved. These modeling methods can then be used to investigate the impacts of urban design and transportation management choices on air quality, pollution exposures, and related inequality. This work will address these needs with three objectives: 1) to improve modeling methods for investigating interactions between city and transportation design choices and air pollution exposures, 2) to characterize current exposures and the social distribution of exposures to traffic-related air pollutants for the case study area of Hillsborough County, Florida, and 3) to determine expected impacts of urban design and transportation management choices on air quality, air pollution exposures, and exposure inequality. To achieve these objectives, the impacts of a small-scale transportation management project, specifically the '95 Express' high occupancy toll lane project, on pollutant emissions and nearby air quality was investigated. Next, a modeling method capable of characterizing spatiotemporally resolved pollutant emissions, concentrations, and exposures was developed and applied to estimate the impact of traffic-related pollutants on exposure and exposure inequalities among several population subgroups in Hillsborough County, Florida. Finally, using these results as baseline, the impacts of sprawl and compact urban forms, as well as vehicle fleet electrification

Correlations of particle number concentrations and metals with nitrogen oxides and other traffic-related air pollutants in Glasgow and London

Science.gov (United States)

Sánchez Jiménez, Araceli; Heal, Mathew R.; Beverland, Iain J.

2012-07-01

Particle number concentration (PNC) and transition metal content are implicated in the health effects of airborne particulate matter (PM) but they are difficult to measure so consequently their temporal and spatial variations are not well characterized. Daily concentrations of PNC and particle-bound water-soluble metals (V, Cr, Mn, Fe, Ni, Cu, As, Cd and Pb) were measured at background and kerbside sites in Glasgow and London to examine if other metrics of air pollution such as optical darkness (absorbance) of collected filter samples of PM, gravimetric PM, and NO, NO2 and CO gas concentrations, can be used as surrogates for the temporal and spatial variations of the former. NO2 and NOx exhibited a high degree of within-site correlation and with PNC and water-soluble metals (Fe, Cu, As, Cd, Pb) at background sites in both cities. There is therefore potential to use NO2 and NOx as surrogates for PNC and water-soluble metal at background sites. However, correlation was weaker in complex street canyon environments where pollutant concentrations are strongly affected by local sources and the small-scale variations in pollutant dispersion induced by the wind regimes within street canyons. The corollary of the high correlation between NO2 and PNC and water-soluble metals at the background sites is that the latter pollutants may act as confounders for health effects attributed to NO2 from such sites. Concentrations of CO cannot be used as a surrogate for PNC. Increments in daily NOx and NO2 concentrations between trafficked and background sites were shown to be a simple and novel surrogate for daily spatial variation of PNC; for example, increments in NOx explained 78-79% of the variance in PNC at the paired sites in both Glasgow and London, but relationships were city specific. The increments in NOx also explained 70% of the spatial variation in Cu and Ni in Glasgow but not in London. Weekly NO2 measurements derived from passive diffusion tubes were also shown to

Maximum neutron flux in thermal reactors

International Nuclear Information System (INIS)

Strugar, P.V.

1968-12-01

Direct approach to the problem is to calculate spatial distribution of fuel concentration if the reactor core directly using the condition of maximum neutron flux and comply with thermal limitations. This paper proved that the problem can be solved by applying the variational calculus, i.e. by using the maximum principle of Pontryagin. Mathematical model of reactor core is based on the two-group neutron diffusion theory with some simplifications which make it appropriate from maximum principle point of view. Here applied theory of maximum principle are suitable for application. The solution of optimum distribution of fuel concentration in the reactor core is obtained in explicit analytical form. The reactor critical dimensions are roots of a system of nonlinear equations and verification of optimum conditions can be done only for specific examples

Ozone pollution: rising concentrations despite French and EU efforts

International Nuclear Information System (INIS)

Ba, M.; Elichegaray, Ch.

2003-11-01

Ozone is the main indicator of photochemical pollution which is caused by a complex combination of primary pollutants formed by chemical reactions in the troposphere, in the presence of sunlight. These primary pollutants, otherwise known as precursors of ozone (nitrogen oxides, volatile organic compounds and carbon monoxide), are emitted both by natural sources and human activities. In urban areas, during the summer months, ozone is often the main cause of deterioration in air quality. Directive 2002/3/EC relating to ozone in ambient air entered into force on 9 September 2003, superseding the first ozone Directive (92/72/CE) of 21 September 1992. In the last 10 years, monitoring of ozone pollution has considerably progressed in France (the number of analysers has increased tenfold). Emissions of the ozone precursors fell significantly (-27%) between 1990 and 2000 in France as a result of combined efforts in all sectors of activity. However, between 1994 and 2002, ozone levels remained above the information threshold for the protection of human health and vegetation on average more than 100 days a year in rural areas and over 40 days a year in urban and peri-urban areas. Efforts undertaken both in France and other European countries aim to improve the situation and ensure compliance with the requirements of Directive 2002/3/EC. (author)

Increased serum concentrations of persistent organic pollutants among prediabetic individuals

DEFF Research Database (Denmark)

Færch, Kristine Villum; Højlund, Kurt; Vind, Birgitte Falbe

2012-01-01

There is a need for a better understanding of the potential role of persistent organic pollutants (POPs) in the pathogenesis of type 2 diabetes.......There is a need for a better understanding of the potential role of persistent organic pollutants (POPs) in the pathogenesis of type 2 diabetes....

Spatiotemporal analysis of particulate matter, sulfur dioxide and carbon monoxide concentrations over the city of Rio de Janeiro, Brazil

Science.gov (United States)

Zeri, Marcelo; Oliveira-Júnior, José Francisco; Lyra, Gustavo Bastos

2011-09-01

Time series of pollutants and weather variables measured at four sites in the city of Rio de Janeiro, Brazil, between 2002 and 2004, were used to characterize temporal and spatial relationships of air pollution. Concentrations of particulate matter (PM10), sulfur dioxide (SO2) and carbon monoxide (CO) were compared to national and international standards. The annual median concentration of PM10 was higher than the standard set by the World Health Organization (WHO) on all sites and the 24 h means exceeded the standards on several occasions on two sites. SO2 and CO did not exceed the limits, but the daily maximum of CO in one of the stations was 27% higher on weekends compared to weekdays, due to increased activity in a nearby Convention Center. Air temperature and vapor pressure deficit have both presented the highest correlations with pollutant's concentrations. The concentrations of SO2 and CO were not correlated between sites, suggesting that local sources are more important to those pollutants compared to PM10. The time series of pollutants and air temperature were decomposed in time and frequency by wavelet analysis. The results revealed that the common variability of air temperature and PM10 is dominated by temporal scales of 1-8 days, time scales that are associated with the passage of weather events, such as cold fronts.

Flotation as a remediation technique for heavily polluted dredged material. 1. A feasibility study.

Science.gov (United States)

Cauwenberg, P; Verdonckt, F; Maes, A

1998-01-19

The flotation behaviour of highly polluted dredged material was investigated at different pH values by mechanical agitated (Denver) flotation. Up to 80% of cadmium, copper, lead and zinc could be concentrated in the froth layer which represented only 30% of the total mass. The maximum specificity for heavy metals, defined as the concentrating factor, was obtained at pH 8-9. The maximum recovery of heavy metals on the other hand was found to be reached at elevated pH values (pH 12). In addition the specificity of the flotation process for the transition metals could be assigned to their presence as metal sulphides in the dredged material. However, the interaction with organic matter is an important factor in determining their flotability. The carbonate fraction was irrelevant for the flotation behaviour of heavy metals.

Volatile Organic Compounds (VOCs) in the Ambient Air Of Concentration Unit of Sar-Cheshmeh Copper Complex

International Nuclear Information System (INIS)

Faghihi-Zrandi, A.; Akhgar, M. R.

2016-01-01

Air pollutants including gases, vapors and particles, are emitted from different sources. Volatile organic compounds are the most important pollutants in the ambient air of industries. The present study was carried out to identify and measurement of volatile organic compounds in concentration unit of Sar-Cheshmeh Copper Complex. In this study, sampling of the volatile organic compounds was done by using activated charcoal tube. To identify and measure these compounds gas chromatography/mass spectroscopy were used. Thirteen volatile organic compounds were identified in the ambient air of concentration unit. Among these compounds, the mean value and maximum concentration of isopropyl alcohol and nonane were 255, 640 μg/m3 and 1577, 14400 μg/m3, respectively. By using SPSS software and independent sample t- test, showed that there were no significant difference between mean value concentration of isopropyl alcohol and nonane in the ambient air and TLV values of these compounds (isopropyl alcohol; 200 ppm and nonane; 200 ppm) (P >0.05).

The role of meteorological conditions and pollution control strategies in reducing air pollution in Beijing during APEC 2014 and Victory Parade 2015

Science.gov (United States)

Liang, Pengfei; Zhu, Tong; Fang, Yanhua; Li, Yingruo; Han, Yiqun; Wu, Yusheng; Hu, Min; Wang, Junxia

2017-11-01

To control severe air pollution in China, comprehensive pollution control strategies have been implemented throughout the country in recent years. To evaluate the effectiveness of these strategies, the influence of meteorological conditions on levels of air pollution needs to be determined. Using the intensive air pollution control strategies implemented during the Asia-Pacific Economic Cooperation Forum in 2014 (APEC 2014) and the 2015 China Victory Day Parade (Victory Parade 2015) as examples, we estimated the role of meteorological conditions and pollution control strategies in reducing air pollution levels in Beijing. Atmospheric particulate matter of aerodynamic diameter ≤ 2.5 µm (PM2.5) samples were collected and gaseous pollutants (SO2, NO, NOx, and O3) were measured online at a site in Peking University (PKU). To determine the influence of meteorological conditions on the levels of air pollution, we first compared the air pollutant concentrations during days with stable meteorological conditions. However, there were few days with stable meteorological conditions during the Victory Parade. As such, we were unable to estimate the level of emission reduction efforts during this period. Finally, a generalized linear regression model (GLM) based only on meteorological parameters was built to predict air pollutant concentrations, which could explain more than 70 % of the variation in air pollutant concentration levels, after incorporating the nonlinear relationships between certain meteorological parameters and the concentrations of air pollutants. Evaluation of the GLM performance revealed that the GLM, even based only on meteorological parameters, could be satisfactory to estimate the contribution of meteorological conditions in reducing air pollution and, hence, the contribution of control strategies in reducing air pollution. Using the GLM, we found that the meteorological conditions and pollution control strategies contributed 30 and 28 % to the reduction

Comparative estimation of soil and plant pollution in the impact area of air emissions from an aluminium plant after technogenic load reduction.

Science.gov (United States)

Evdokimova, Galina A; Mozgova, Natalya P

2015-01-01

The work provides a comparative analysis of changes in soil properties in the last 10-13 years along the pollution gradient of air emissions from Kandalaksha aluminium plant in connection with the reduction of their volume. The content of the priority pollutant fluorine (F) in atmospheric precipitation and in the organic horizon of soil in the plant impact zone significantly decreased in 2011-2013 compared to 2001. The aluminium concentrations reduced only in immediate proximity to the plant (2 km). The fluorine, calcium (Ca) and magnesium (Mg) concentrations are higher in liquid phase compared to solid phase thus these elements can migrated to greater distances from the pollution source (up to 15-20 km). Silicon (Si), aluminium (Al), iron (Fe) and phosphorus (P) can be found only in solid phases and in fall-out within the 5 km. The acidity of soil litter reduced by 2 pH units in the proximity to the plot within the 2 km. The zone of maximum soil contamination decreased from 2.5 km to 1.5 km from the emission source, the zones of heavy and moderate pollution reduced by 5 km in connection with the reduction of pollutant emissions in the plant. A high correlation between the fluorine concentrations in vegetables and litter was found. Higher fluorine concentrations in the soil result in its accumulation in plants. Mosses accumulate fluorine most intensively.

heavy metal pollution asse al pollution assessment in the sediments

African Journals Online (AJOL)

User

ABSTRACT. Sediments were collected from Dumba and to assess the pollution statusof the sedim. Cadmium (Cd), Chromium (Cr), Copper (Cu. (Zn) and Arsenic (As) were analysed using concentration of heavy metals varies bet with standard average shale to assess pollution in Dumba and KwataYobe sedi assessed ...

Distribution of pollutant transport at landfill site, Taiping, Perak, Malaysia

International Nuclear Information System (INIS)

Roslanzairi Mostapa; Kamarudin Samuding; Mohd Tadza Abdul Rahman; Mohd Rifaie Mohd Murtadza; Ismail Abustan; Mohd Suhaimi Hamzah; Shamsiah Abdul Rahman; Nazaratul Ashifa Abdullah Salim

2004-01-01

This paper describes the preliminary report on the distribution of pollutant transport at Taiping municipal waste disposal site, Perak. This study involved the sampling of surface water and groundwater at various locations within the area. The hydrogeochemical method was used to determine the concentration of heavy metals i.e. Cr, Mn, Zn, As, Cd, Pb, and Fe. In-situ conductivity measurement was taken as a screening method for preliminary analysis purpose. Most of the groundwater at several boreholes contains high concentration of heavy metals. This indicates that some of the groundwater has been contaminated. The presence of heavy metals concentration in the surface water (river and pond) seems to be relatively low compared to maximum contaminant level (MCL) allowed in drinking water. Heavy metals that show significant changes and exceed the MCL are Mn, Zn, Pb and Fe. The conductivity value for the first sampling at various locations on December 2003 ranges from 60 - 12830 μS/cm and the these values were relatively increased on the second sampling in February 2004 which ranges from 155 - 13760 μS/cm. The sampling will be continued to obtain several series of complete data so that a conclusive evaluation of pollutant transport can be made. (Author)

Sono assisted electrocoagulation process for the removal of pollutant from pulp and paper industry effluent.

Science.gov (United States)

Asaithambi, P; Aziz, Abdul Raman Abdul; Sajjadi, Baharak; Daud, Wan Mohd Ashri Bin Wan

2017-02-01

In the present work, the efficiency of the sonication, electrocoagulation, and sono-electrocoagulation process for removal of pollutants from the industrial effluent of the pulp and paper industry was compared. The experimental results showed that the sono-electrocoagulation process yielded higher pollutant removal percentage compared to the sonication and electrocoagulation process alone. The effect of the operating parameters in the sono-electrocoagulation process such as electrolyte concentration (1-5 g/L), current density (1-5 A/dm 2 ), effluent pH (3-11), COD concentration (1500-6000 mg/L), inter-electrode distance (1-3 cm), and electrode combination (Fe and Al) on the color removal, COD removal, and power consumption were studied. The maximum color and COD removal percentages of 100 and 95 %, respectively, were obtained at the current density of 4 A/dm 2 , electrolyte concentration of 4 g/L, effluent pH of 7, COD concentration of 3000 mg/L, electrode combination of Fe/Fe, inter-electrode distance of 1 cm, and reaction time of 4 h, respectively. The color and COD removal percentages were analyzed by using an UV/Vis spectrophotometer and closed reflux method. The results showed that the sono-electrocoagulation process could be used as an efficient and environmental friendly technique for complete pollutant removal.

Model predictions of ambient pollution concentration | Olaniyan ...

African Journals Online (AJOL)

The results show that the emission loads of the pollutants associated with the use of industrial boiler and power generating plant are in decreasing order of magnitude as NOx > CO > TSP > SO2 > VOC > SO,sub>3 and NOx > TSP > CO > HC > SO2 respectively. The emission load of SO2 is 74.6% in power generating plant, ...

Analysis and Pollution Assessment of Heavy Metal in Soil, Perlis

International Nuclear Information System (INIS)

Siti Norbaya Mat Ripin; Siti Norbaya Mat Ripin; Sharizal Hasan; Mohd Lias Kamal; NorShahrizan Mohd Hashim

2014-01-01

Concentration of 5 heavy metals (Cu, Cr, Ni, Cd, Pb) were studied in the soils around Perlis, to assess heavy metals contamination distribution due to industrialization, urbanization and agricultural activities. Soil samples were collected at depth of 0-15 cm in eighteen station around Perlis. The soil samples (2 mm) were obtained duplicates and subjected to hot block digestion and the concentration of total metal was determined via ICP-MS. Overall concentrations of Cu, Cr, Ni, Cd and Pb in the soil samples ranged from 0.38-240.59, 0.642-3.921, 0.689-2.398, 0-0.63 and 0.39-27.47 mg/ kg respectively. The concentration of heavy metals in the soil display the following decreasing trend: Cu> Pb> Cr> Ni> Cd. From this result, found that level of heavy metal in soil near centralized Chuping industrial areas give maximum value compared with other location in Perlis. The Pollution index revealed that only 11 % of Cu and 6 % of Cd were classes as heavily contaminated. Meanwhile, Cu and Pb showed 6 % from all samples result a moderately contaminated and the others element give low contamination. Results of combined heavy metal concentration and heavy metal assessment indicate that industrial activities and traffic emission represent most important sources for Cu, Cd and Pb whereas Cr, Ni mainly from natural sources. Increasing anthropogenic influences on the environment, especially pollution loadings, have caused negative changes in natural ecosystems and decreased biodiversity. (author)

A revised method to calculate the concentration time integral of atmospheric pollutants

International Nuclear Information System (INIS)

Voelz, E.; Schultz, H.

1980-01-01

It is possible to calculate the spreading of a plume in the atmosphere under nonstationary and nonhomogeneous conditions by introducing the ''particle-in-cell'' method (PIC). This is a numerical method by which the transport of and the diffusion in the plume is reproduced in such a way, that particles representing the concentration are moved time step-wise in restricted regions (cells) and separately with the advection velocity and the diffusion velocity. This has a systematical advantage over the steady state Gaussian plume model usually used. The fixed-point concentration time integral is calculated directly instead of being substituted by the locally integrated concentration at a constant time as is done in the Gaussian model. In this way inaccuracies due to the above mentioned computational techniques may be avoided for short-time emissions, as may be seen by the fact that both integrals do not lead to the same results. Also the PIC method enables one to consider the height-dependent wind speed and its variations while the Gaussian model can be used only with averaged wind data. The concentration time integral calculated by the PIC method results in higher maximum values in shorter distances to the source. This is an effect often observed in measurements. (author)

Vehicular pollution modeling using the operational street pollution model (OSPM) for Chembur, Mumbai (India)

DEFF Research Database (Denmark)

Kumar, Awkash; Ketzel, Matthias; Patil, Rashmi S.

2016-01-01

Megacities in India such as Mumbai and Delhi are among the most polluted places in the world. In the present study, the widely used operational street pollution model (OSPM) is applied for assessing pollutant loads in the street canyons of Chembur, a suburban area just outside Mumbai city. Chembur...... concentrations from the routine monitoring performed in Mumbai. NOx emissions originate mainly from vehicles which are ground-level sources and are emitting close to where people live. Therefore, those emissions are highly relevant. The modeled NOx concentration compared satisfactorily with observed data...

Human Exposure Assessment for Air Pollution.

Science.gov (United States)

Han, Bin; Hu, Li-Wen; Bai, Zhipeng

2017-01-01

Assessment of human exposure to air pollution is a fundamental part of the more general process of health risk assessment. The measurement methods for exposure assessment now include personal exposure monitoring, indoor-outdoor sampling, mobile monitoring, and exposure assessment modeling (such as proximity models, interpolation model, air dispersion models, and land-use regression (LUR) models). Among these methods, personal exposure measurement is considered to be the most accurate method of pollutant exposure assessment until now, since it can better quantify observed differences and better reflect exposure among smaller groups of people at ground level. And since the great differences of geographical environment, source distribution, pollution characteristics, economic conditions, and living habits, there is a wide range of differences between indoor, outdoor, and individual air pollution exposure in different regions of China. In general, the indoor particles in most Chinese families comprise infiltrated outdoor particles, particles generated indoors, and a few secondary organic aerosol particles, and in most cases, outdoor particle pollution concentrations are a major contributor to indoor concentrations in China. Furthermore, since the time, energy, and expense are limited, it is difficult to measure the concentration of pollutants for each individual. In recent years, obtaining the concentration of air pollutants by using a variety of exposure assessment models is becoming a main method which could solve the problem of the increasing number of individuals in epidemiology studies.

Ground-level ozone pollution and its health impacts in China

Science.gov (United States)

Liu, Huan; Liu, Shuai; Xue, Boru; Lv, Zhaofeng; Meng, Zhihang; Yang, Xiaofan; Xue, Tao; Yu, Qiao; He, Kebin

2018-01-01

In recent years, ground-level ozone pollution in China has become an increasingly prominent problem. This study simulated and analyzed spatiotemporal distribution of ozone and exposure level by the Weather Research and Forecasting (WRF)-Community Multiscale Air Quality (CMAQ) models and monitoring data from 1516 national air quality monitoring stations in China during 2015. The simulation results show that the Sichuan Basin, Shandong, Shanxi, Henan, Anhui, Qinghai-Tibetan Plateau, Yangtze River Delta (YRD), Pearl River Delta (PRD) and Beijing-Tianjin-Hebei (BTH) region had relatively high average annual concentrations of ozone. The regions with more than 10% nonattainment days of 160 μg/m3 (daily maximum 8-h) are mainly concentrated in BTH, Shandong Peninsula and YRD, where large seasonal variations were also found. Exposure levels were calculated based on population data and simulated ozone concentrations. The cumulative population exposed to daily maximum 8-h concentration greater than or equal to 100 μg/m3 was 816.04 million, 61.17% of the total. Three methods were used to estimate the mortality of chronic obstructive pulmonary disease (COPD) attributable to ozone. A comparative study using different exposure concentrations and threshold concentrations found large variations among these methods, although they were all peer-reviewed methods. The estimated mortality of COPD caused by ozone in China in 2015 ranged from 55341 to 80280, which mainly distributed in Beijing, Shandong, Henan, Hubei and Sichuan Province, the YRD and PRD region.

Isolation of Crude Oil from Polluted Waters Using Biosurfactants Pseudomonas Bacteria: Assessment of Bacteria Concentration Effects

Directory of Open Access Journals (Sweden)

A. Khalifeh

2013-04-01

Full Text Available Biological decomposition techniques and isolation of environmental pollutions using biosurfactants bacteria are effective methods of environmental protection. Surfactants are amphiphilic compounds that are produced by local microorganisms and are able to reduce the surface and the stresses between surfaces. As a result, they will increase solubility, biological activity, and environmental decomposition of organic compounds. This study analyzes the effects of biosurfactants on crude oil recovery and its isolation using pseudomonas sea bacteria species. Preparation of biosurfactants was done in glass flasks and laboratory conditions. Experiments were carried out to obtain the best concentration of biosurfactants for isolating oil from water and destroying oil-in-water or water-in-oil emulsions in two pH ranges and four saline solutions of different concentrations. The most effective results were gained when a concentration of 0.1% biosurfactants was applied.

Indoor air pollution

International Nuclear Information System (INIS)

Spengler, J.D.

1985-01-01

Although official efforts to control air pollution have traditionally focused on outdoor air, it is now apparent that elevated contaminant concentrations are common inside some private and public buildings. Concerns about potential public health problems due to indoor air pollution are based on evidence that urban residents typically spend more than 90 percent of their time indoors, concentrations of some contaminants are higher indoors than outdoors, and for some pollutants personal exposures are not characterized adequately by outdoor measurements. Among the more important indoor contaminants associated with health or irritation effects are passive tobacco smoke, radon decay products, carbon monoxide, nitrogen dioxide, formaldehyde, asbestos fibers, microorganisms and aeroallergens. Efforts to assess health risks associated with indoor air pollution are limited by insufficient information about the number of people exposed, the pattern and severity of exposures, and the health consequences of exposures. An overall strategy should be developed to investigate indoor exposures, health effects, control options, and public policy alternatives

Pollution distribution of heavy metals in surface soil at an informal electronic-waste recycling site.

Science.gov (United States)

Fujimori, Takashi; Takigami, Hidetaka

2014-02-01

We studied distribution of heavy metals [lead (Pb), copper (Cu) and zinc (Zn)] in surface soil at an electronic-waste (e-waste) recycling workshop near Metro Manila in the Philippines to evaluate the pollution size (spot size, small area or the entire workshop), as well as to assess heavy metal transport into the surrounding soil environment. On-site length-of-stride-scale (~70 cm) measurements were performed at each surface soil point using field-portable X-ray fluorescence (FP-XRF). The surface soil at the e-waste recycling workshop was polluted with Cu, Zn and Pb, which were distributed discretely in surface soil. The site was divided into five areas based on the distance from an entrance gate (y-axis) of the e-waste recycling workshop. The three heavy metals showed similar concentration gradients in the y-axis direction. Zn, Pb and Cu concentrations were estimated to decrease to half of their maximum concentrations at ~3, 7 and 7 m from the pollution spot, respectively, inside the informal e-waste recycling workshop. Distance from an entrance may play an important role in heavy metal transport at the soil surface. Using on-site FP-XRF, we evaluated the metal ratio to characterise pollution features of the solid surface. Variability analysis of heavy metals revealed vanishing surficial autocorrelation over metre ranges. Also, the possibility of concentration prediction at unmeasured points using geostatistical kriging was evaluated, and heavy metals had a relative "small" pollution scales and remained inside the original workshop compared with toxic organohalogen compounds. Thus, exposure to heavy metals may directly influence the health of e-waste workers at the original site rather than the surrounding habitat and environmental media.

Pollution Assessment of Toxic and Potentially Toxic Elements in Agricultural Soils of the City Addis Ababa, Ethiopia.

Science.gov (United States)

Aschale, Minbale; Sileshi, Yilma; Kelly-Quinn, Mary; Hailu, Dereje

2017-02-01

Due to the significantly fast urban expansion and increased industrial activities, the soils in the farms in Addis Ababa are contaminated by some toxic and potentially toxic elements (As, V, Cr, Fe, Co, Ni, Cu, B, Ba, Sr, Zn, Mn, Pb and Cd) in varying degrees. The mean concentrations of Cr, Ni, As and B in most of the soil farms were found to be higher than the maximum recommended limits. The mean concentrations of Cd, Cu, Pb, Co, Ni and Mn were found to be higher than the background soil concentrations given for uncontaminated soils. Multivariate analyses coupled with correlation analysis were used to identify possible sources. The geo-accumulation index values for Cr, Mn and Pb indicated that the farm soils were unpolluted to moderately polluted as a result of anthropogenic activities. A comprehensive environmental management strategy should be formulated by the government to measure further pollution of the farmland soil.

City air pollution of polycyclic aromatic hydrocarbons and other mutagens: occurrence, sources and health effects

DEFF Research Database (Denmark)

Nielsen, T.; Ejsing Jørgensen, Hans; Larsen, J.C.

1996-01-01

The presence of polycyclic aromatic hydrocarbons (PAH), mutagens and other air pollutants was investigated in a busy street in central Copenhagen and in a park area adjacent to the street. The winter concentration of benzo(a)pyrene was 4.4+/-1.2 ng/m(3) in the street air and 1.4+/-0.6 ng/m(3......) in the city park. The atmospheric concentrations of PAH decreased in the order of: street > city background air similar to suburbs > village > open land. The traffic contribution of PAH to street air was estimated to be 90% on working days and 60% during weekends and its contribution to city background air...... was estimated to be 40%. Four different approaches to evaluate the health effects are discussed. The direct effect of PAH air pollution, and other mutagens, is considered to be a maximum of five lung cancer cases each year out of one million people....

The reduction of oil pollutants of petroleum products storage-tanks sludge using low-cost adsorbents

Directory of Open Access Journals (Sweden)

Mokhtari-Hosseini Zahra Beagom

2017-01-01

Full Text Available Disposal of storage tank sludge in oil depots is a major environmental concern due to the high concentration of hydrocarbons involved. This paper investigates the reduction of the sludge oil pollutants with initial oil and grease concentration of about 50 mass% using low cost adsorbents. Among the examined adsorbents, sawdust indicated the maximum removal of oil and grease. The screening and optimizing of process parameters were evaluated employing Plackett-Burman design and response surface method. For the optimized conditions, more than 60 mass% of oil and grease from the sludge was removed. Moreover, it was found that sawdust adsorption of the oil and grease approximately followed the Freundlich isotherm. The results indicated that oil pollutants of sludge could be reduced using sawdust as a low-cost, available and flammable adsorbent so that thus saturated adsorbents could be used as fuel in certain industries.

Trends of atmospheric black carbon concentration over the United Kingdom

Science.gov (United States)

Singh, Vikas; Ravindra, Khaiwal; Sahu, Lokesh; Sokhi, Ranjeet

2018-04-01

The continuous observations over a period of 7 years (2009-2016) available at 7 locations show declining trend of atmospheric BC in the UK. Among all the locations, the highest decrease of 8 ± 3 percent per year was observed at the Marylebone road in London. The detailed analysis performed at 21 locations during 2009-2011 shows that average annual mean atmospheric BC concentration were 0.45 ± 0.10, 1.47 ± 0.58, 1.34 ± 0.31, 1.83 ± 0.46 and 9.72 ± 0.78 μgm-3 at rural, suburban, urban background, urban centre and kerbside sites respectively. Around 1 μgm-3 of atmospheric BC could be attributed to urban emission, whereas traffic contributed up to 8 μg m-3 of atmospheric BC near busy roads. Seasonal pattern was also observed at all locations except rural and kerbside location, with maximum concentrations (1.2-4 μgm-3) in winter. Further, minimum concentrations (0.3-1.2 μgm-3) were observed in summer and similar concentrations in spring and fall. At suburban and urban background locations, similar diurnal pattern were observed with atmospheric BC concentration peaks (≈1.8 μg m-3) in the morning (around 9 a.m.) and evening (7-9 p.m.) rush hours, whereas minimum concentrations were during late night hours (peak at 5 a.m.) and the afternoon hours (peak at 2 p.m.). The urban centre values show a similar morning pattern (peak at 9 a.m.; concentration - 2.5 μgm-3) in relation to background locations but only a slight decrease in concentration in the afternoon which remained above 2 μgm-3 till midnight. It is concluded that the higher flow of traffic at urban centre locations results in higher atmospheric BC concentrations throughout the day. Comparison of weekday and weekend daily averaged atmospheric BC showed maximum concentrations on Friday, having minimum levels on Sunday. This study will help to refine the atmospheric BC emission inventories and provide data for air pollution and climate change models evaluation, which are used to formulate air pollution

Particulate Matter and Gaseous Pollutions in Three Metropolises along the Chinese Yangtze River: Situation and Implications.

Science.gov (United States)

Mao, Mao; Zhang, Xiaolin; Yin, Yan

2018-05-28

The situation of criteria atmospheric pollutants, including particulate matter and trace gases (SO₂, NO₂, CO and O₃), over three metropolises (Chongqing, Wuhan, and Nanjing), representing the upstream, midstream and downstream portions of the Yangtze River Basin from September 2015 to August 2016 were analyzed. The maximum annual mean PM 2.5 and PM 10 concentrations were 61.3 and 102.7 μg/m³ in Wuhan, while highest annual average gaseous pollutions occurred in Nanjing, with 49.6 and 22.9 ppb for 8 h O₃ and NO₂, respectively. Compared to a few years ago, SO₂ and CO mass concentrations have dropped to well below the qualification standards, and the O₃ and NO₂ concentrations basically meet the requirements though occasionally is still high. In contrary, about 13%, 25%, 22% for PM 2.5 , and 4%, 17%, 15% for PM 10 exceed the Chinese Ambient Air Quality Standard (CAAQS) Grade II. Particulate matter, especially PM 2.5 , is the most frequent major pollutant to poor air quality with 73%, 64% and 88% accounting for substandard days. Mean PM 2.5 concentrations on PM 2.5 episode days are 2⁻3 times greater than non-episode days. On the basis of calculation of PM 2.5 /PM 10 and PM 2.5 /CO ratios, the enhanced particulate matter pollution on episode days is closely related to secondary aerosol production. Except for O₃, the remaining five pollutants exhibit analogous seasonal patterns, with the highest magnitude in winter and lowest in summer. The results of back trajectories show that air pollution displays synergistic effects on local emissions and long range transport. O₃ commonly demonstrated negative correlations with other pollutants, especially during winter, while moderate to strong positive correlation between particulate matter and NO₂, SO₂, CO were seen. Compared to pollutant substandard ratios over three megacities in eastern China (Beijing, Shanghai, and Guangzhou), the situation in our studied second-tier cities are also severe. The

Control of Sewer systems and Wastewater treatment plants using pollutant concentration profiles

DEFF Research Database (Denmark)

Bechmann, Henrik; Nielsen, Marinus K.; Madsen, Henrik

1998-01-01

On-line measurements of pollutants in the wastewater combined with grey-box modelling are used to estimate the amount of deposits in the sewer system. The pollutant mass flow at the wastewater treatment plant is found to consist of a diurnal profile minus the deposited amount of pollutants...

Comparison of point-source pollutant loadings to soil and groundwater for 72 chemical substances.

Science.gov (United States)

Yu, Soonyoung; Hwang, Sang-Il; Yun, Seong-Taek; Chae, Gitak; Lee, Dongsu; Kim, Ki-Eun

2017-11-01

Fate and transport of 72 chemicals in soil and groundwater were assessed by using a multiphase compositional model (CompFlow Bio) because some of the chemicals are non-aqueous phase liquids or solids in the original form. One metric ton of chemicals were assumed to leak in a stylized facility. Scenarios of both surface spills and subsurface leaks were considered. Simulation results showed that the fate and transport of chemicals above the water table affected the fate and transport of chemicals below the water table, and vice versa. Surface spill scenarios caused much less concentrations than subsurface leak scenarios because leaching amounts into the subsurface environment were small (at most 6% of the 1 t spill for methylamine). Then, simulation results were applied to assess point-source pollutant loadings to soil and groundwater above and below the water table, respectively, by multiplying concentrations, impact areas, and durations. These three components correspond to the intensity of contamination, mobility, and persistency in the assessment of pollutant loading, respectively. Assessment results showed that the pollutant loadings in soil and groundwater were linearly related (r 2  = 0.64). The pollutant loadings were negatively related with zero-order and first-order decay rates in both soil (r = - 0.5 and - 0.6, respectively) and groundwater (- 1.0 and - 0.8, respectively). In addition, this study scientifically defended that the soil partitioning coefficient (K d ) significantly affected the pollutant loadings in soil (r = 0.6) and the maximum masses in groundwater (r = - 0.9). However, K d was not a representative factor for chemical transportability unlike the expectation in chemical ranking systems of soil and groundwater pollutants. The pollutant loadings estimated using a physics-based hydrogeological model provided a more rational ranking for exposure assessment, compared to the summation of persistency and transportability scores in

Characteristics of aerosol pollution during heavy haze events in Suzhou, China

Science.gov (United States)

Tian, M.; Wang, H. B.; Chen, Y.; Yang, F. M.; Zhang, X. H.; Zou, Q.; Zhang, R. Q.; Ma, Y. L.; He, K. B.

2015-11-01

A comprehensive measurement was carried out to analyze the heavy haze events in Suzhou in January 2013 when extremely severe haze pollution occurred in many cities in China especially in the East. Hourly concentrations of PM2.5, chemical composition (including water-soluble inorganic ions, OC, and EC), and gas-phase precursors were obtained via on-line monitoring system. Based on these data, detailed aerosol composition, light extinction and gas-phase precursors were analyzed to understand the characteristics of the haze events, moreover, the formation mechanism of nitrate and sulfate in PM2.5 and the regional sources deduced from trajectory and PSCF were discussed to explore the origin of the heavy aerosol pollution. The results showed that frequent haze events were occurred on January 2013 and the concentrations of PM2.5 often exceeded 150 μg m-3 during the haze occurrence, with a maximum concentration of 324 μg m-3 on 14 January 2013. Unfavorable weather conditions (high RH, and low rainfall, wind speed and atmospheric pressure), high concentration of secondary aerosol species (including SO42-, NO3-, NH4+, and SOC) and precursors were observed during the haze events. Additionally, OM, (NH4)2SO4, NH4NO3 were demonstrated to be the major contributors to the visibility impairment but the share differed from haze events. This study also found that the high concentration of sulfate might be explained by the heterogeneous reactions in the aqueous surface layer of pre-existing particles or in cloud processes while nitrate might be mainly formed through homogeneous gas-phase reactions. The results of trajectory clustering and the PSCF method manifested that aerosol pollutions in the studied areas were mainly affected by local activities and surrounding sources transported from nearby cities.

Characterization of ambient air pollution for stochastic health models

Energy Technology Data Exchange (ETDEWEB)

Batterman, S.A.

1981-08-01

This research is an analysis of various measures of ambient air pollution useful in cross-sectional epidemiological investigations and rick assessments. The Chestnut Ridge area health effects investigation, which includes a cross-sectional study of respiratory symptoms in young children, is used as a case study. Four large coal-fired electric generating power plants are the dominant pollution sources in this area of western Pennsylvania. The air pollution data base includes four years of sulfur dioxide and five years of total suspended particulate concentrations at seventeen monitors. Some 70 different characterizations of pollution are constructed and tested. These include pollutant concentrations at various percentiles and averaging times, exceedence measures which show the amount of time a specified threshold concentration is exceeded, and several dosage measures which transform non-linear dose-response relationships onto pollutant concentrations.

Primary pollutants and potential photochemical smog formation in Makkah, Saudi Arabia

International Nuclear Information System (INIS)

Nasralla, M.M.; Seroji, A.R.

2007-01-01

This study was conducted in Mina Valley and the central district of the holy city, Makkah, during the pilgrimage (Hajj) season of 1424 Hijri (2004). During this season, more than 2.5 million people gathered in Makkah to perform the Hajj rituals. Two mobile air pollution laboratories were used to monitor NO, NO2, NOx, non-methane hydrocarbons and ozone (O3) in the atmosphere in Mina and Makkah. Instruments were calibrated periodically against standard gases. The present investigation showed clearly an ideal diurnal cycle of local ozone formation. Although the intensity of the incoming UV radiation was the lowest compared with other months of the year, recorded ozone levels approached the maximum allowable levels of 150 ug/m3 in Mina, and exceeded 160 ug/m3 in Makkah during the pilgrimage period. The problem was intensified by the high record levels NOx, sometimes reaching more than 800 ug/m3, 1h average, coupled with 1h average concentration of about 3 ppm non-methane hydrocarbons. Furthermore, the average maximum hourly ozone concentrations increased gradually from less than 60 ug/m3 during February to reach more than 200 ug/m3 (as an indication of smog formation) during some days of May. This coincides with the increase in the intensity of the incoming UV radiation reaching its maximum level in May. Consequently, it can be concluded that Makkah may face severe air pollution episodes when the pilgrimage season shifts to the summer months in the next few years. This may pose acute health problems for the elderly people and those with respiratory health problems. Good air quality and transportation management as well as the use of alternative clean fuel are highly recommended. (author)

The Empirical Relationship between Mining Industry Development and Environmental Pollution in China.

Science.gov (United States)

Li, Gerui; Lei, Yalin; Ge, Jianping; Wu, Sanmang

2017-03-02

This study uses a vector autoregression (VAR) model to analyze changes in pollutants among different mining industries and related policy in China from 2001 to 2014. The results show that: (1) because the pertinence of standards for mining waste water and waste gas emissions are not strong and because the maximum permissible discharge pollutant concentrations in these standards are too high, ammonia nitrogen and industrial sulfur dioxide discharges increased in most mining industries; (2) chemical oxygen demand was taken as an indicator of sewage treatment in environmental protection plans; hence, the chemical oxygen demand discharge decreased in all mining industries; (3) tax reduction policies, which are only implemented in coal mining and washing and extraction of petroleum and natural gas, decreased the industrial solid waste discharge in these two mining industries.

The Empirical Relationship between Mining Industry Development and Environmental Pollution in China

Directory of Open Access Journals (Sweden)

Gerui Li

2017-03-01

Full Text Available This study uses a vector autoregression (VAR model to analyze changes in pollutants among different mining industries and related policy in China from 2001 to 2014. The results show that: (1 because the pertinence of standards for mining waste water and waste gas emissions are not strong and because the maximum permissible discharge pollutant concentrations in these standards are too high, ammonia nitrogen and industrial sulfur dioxide discharges increased in most mining industries; (2 chemical oxygen demand was taken as an indicator of sewage treatment in environmental protection plans; hence, the chemical oxygen demand discharge decreased in all mining industries; (3 tax reduction policies, which are only implemented in coal mining and washing and extraction of petroleum and natural gas, decreased the industrial solid waste discharge in these two mining industries.

Spatio-temporal variational characteristics analysis of heavy metals pollution in water of the typical northern rivers, China

Science.gov (United States)

Lu, Hongwei; Yu, Sen

2018-04-01

The rapid urbanization and industrialization in developing countries have increased pollution by heavy metals, which is a concern for human health and the environment. In this study, according to the data obtained from the monitoring stations in the Songhua River basin, the multivariate statistical analysis methods are applied to the hydrological data of the Songhua River basin in order to examine the relation between human activities and the spatio-temporal change of heavy metals (Pb and Cu) in water. By comparing the concentrations at different flow periods, the minimum Pb concentrations are found to have occurred most frequently in low flow periods while the maximum values mostly appeared in average flow periods. Moreover, the minimum Cu concentration in the water frequently occurred in high flow periods. The results show there are low Pb and Cu concentrations in upstream and downstream sections and high concentrations in mid-stream sections, and high concentrations are most frequently measured in the sections of Ashihe' downstream and estuary. Moreover, we have predicted the future (during 2018-2025) trend of the change for the heavy metals pollution in the rivers. The results demonstrated intense human activities are the most important factor causing jump features of typical heavy metal pollution in the different periods for different sections of this study area. The research would provide decision-making and planning for the Songhua River basin during the period of China's 13th Five-Year Plan.

Modelling pollutant emissions in diesel engines, influence of biofuel on pollutant formation.

Science.gov (United States)

Petranović, Zvonimir; Bešenić, Tibor; Vujanović, Milan; Duić, Neven

2017-12-01

In order to reduce the harmful effect on the environment, European Union allowed using the biofuel blends as fuel for the internal combustion engines. Experimental studies have been carried on, dealing with the biodiesel influence on the emission concentrations, showing inconclusive results. In this paper numerical model for pollutant prediction in internal combustion engines is presented. It describes the processes leading towards the pollutant emissions, such as spray particles model, fuel disintegration and evaporation model, combustion and the chemical model for pollutant formation. Presented numerical model, implemented in proprietary software FIRE ® , is able to capture chemical phenomena and to predict pollutant emission concentration trends. Using the presented model, numerical simulations of the diesel fuelled internal combustion engine have been performed, with the results validated against the experimental data. Additionally, biodiesel has been used as fuel and the levels of pollutant emissions have been compared to the diesel case. Results have shown that the biodiesel blends release lower nitrogen oxide emissions than the engines powered with the regular diesel. Copyright © 2017 Elsevier Ltd. All rights reserved.

The use of simulated rainfall to study the discharge process and the influence factors of urban surface runoff pollution loads.

Science.gov (United States)

Qinqin, Li; Qiao, Chen; Jiancai, Deng; Weiping, Hu

2015-01-01

An understanding of the characteristics of pollutants on impervious surfaces is essential to estimate pollution loads and to design methods to minimize the impacts of pollutants on the environment. In this study, simulated rainfall equipment was constructed to investigate the pollutant discharge process and the influence factors of urban surface runoff (USR). The results indicated that concentrations of total suspended solids (TSS), total nitrogen (TN), total phosphorus (TP) and chemical oxygen demand (COD) appeared to be higher in the early period and then decreased gradually with rainfall duration until finally stabilized. The capacity and particle size of surface dust, rainfall intensity and urban surface slopes affected runoff pollution loads to a variable extent. The loads of TP, TN and COD showed a positive relationship with the surface dust capacity, whereas the maximum TSS load appeared when the surface dust was 0.0317 g·cm⁻². Smaller particle sizes (pollution carrying capacity of runoff, leading to higher pollution loads. Knowledge of the influence factors could assist in the management of USR pollution loads.

A field study to evaluate the impact of different factors on the nutrient pollutant concentrations in green roof runoff.

Science.gov (United States)

Wang, Xiaochen; Zhao, Xinhua; Peng, Chenrui; Zhang, Xinbo; Wang, Jianghai

2013-01-01

The objectives of this study are to investigate the impact of different factors on the nutrient pollutant concentrations in green roof runoff and to provide reference data for the engineering design of dual substrate layer green roofs. The data were collected from eight different trays under three kinds of artificial rains. The results showed that except for total phosphorus, dual substrate layer green roofs behaved as a sink for most of the nutrient pollutants (significant at p green roof and the depth of the adsorption substrates. Compared with the influence of the substrates, the influence of the plant density and drainage systems was small.

Concentrations of organochlorine pesticides and 2,4,6-trichloroanisole in cork bark.

Science.gov (United States)

Olivella, M Àngels; Caixach, Josep; Planas, Carles; Oliveras, Anna; Jové, Patrícia

2012-02-01

Organochlorine pesticides are persistent lipophilic organic pollutants and tend to accumulate in growing plants. During growth, cork is in contact with the open air for long periods (9-12 years). Owing to the previous widespread use of organochlorine pesticides and their high persistence in the environment, there is a risk that residues of such pesticides may be present in cork. In this study, the concentrations of 14 organochlorine pesticides-all of which are indicators of environmental pollution-were analyzed in cork bark samples from three regions in Spain and one in Portugal. In addition, the concentrations of 2,4,6-trichlorophenol (TCP) and 2,4,6-trichloroanisole (TCA) were also analyzed. Our results show only very low concentrations of lindane, γ-HCH (cork sample from Extremadura (0.1 ng g(-1)) and p,p'-DDE was present at a maximum concentration of 2.9 ng g(-1) in a cork sample from Castile-La Mancha. However, all concentrations were well below the legal limit established by Regulation (EC) No. 396/2005 (10 ng g(-1) in foodstuffs). We can conclude, therefore, that the cork samples we studied complied with food safety standards. Copyright © 2011 Elsevier Ltd. All rights reserved.

Constructed wetland using corncob charcoal substrate: pollutants removal and intensification.

Science.gov (United States)

Liu, Mao; Li, Boyuan; Xue, Yingwen; Wang, Hongyu; Yang, Kai

2017-09-01

To investigate the feasibility of using corncob charcoal substrate in constructed wetlands, four laboratory-scale vertical flow constructed wetlands (VFCWs) were built. Effluent pollutant (chemical oxygen demand (COD), NH 4 + -N, total phosphorus (TP)) concentrations during the experiment were determined to reveal pollutant removal mechanisms and efficiencies at different stages. In the stable stage, a VFCW using clay ceramisite substrate under aeration attained higher COD (95.1%), and NH 4 + -N (95.1%) removal efficiencies than a VFCW using corncob charcoal substrate (91.5% COD, 91.3% NH 4 + -N) under aeration, but lower TP removal efficiency (clay ceramisite 32.0% and corncob charcoal 40.0%). The VFCW with raw corncob substrate showed stronger COD emissions (maximum concentration 3,108 mg/L) than the corncob charcoal substrate (COD was lower than influent). The VFCW using corncob charcoal substrate performed much better than the VFCW using clay ceramisite substrate under aeration when the C/N ratio was low (C/N = 1.5, TN removal efficiency 36.89%, 4.1% respectively). These results suggest that corncob charcoal is a potential substrate in VFCWs under aeration with a unique self -supplying carbon source property in the denitrification process.

Chemical pollution of environment in the cities of Central Siberia: risk for the health of the population

Directory of Open Access Journals (Sweden)

Ludmila Klimatskaya

2015-03-01

Full Text Available pollution in cities including the problem of risk assessment. The aim of the study is to determine carcinogenic and non-carcinogenic risks for the health of the population due to chemical contamination of air, water and food in the cities of the Krasnoyarsk region. Material and methods. The research was conducted in the Center of Hygiene and Epidemiology in the Krasnoyarsk region. 5122 samples of air, 4863 samples of water and 6915 samples of food stuff have been analyzed. Concentration of chemical substances was the base on which individual carcinogenesis risk (ICR and population carcinogenic conventional risks (PCCR and non carcinogenic risks [1] have been calculated. In the industrial cities chemical pollution of air, water and food stuff including carcinogenic substances creates carcinogenic and non-carcinogenic risks of morbidity of the population with the reinforcement of the complex impact, “with” which greatly exceeds the maximum acceptable risks. Results. Chemical pollution of environmental facilities in cities of the Krasnoyarsk region produce complex carcinogenic and non-carcinogenic risks which exceed maximum limit. The greatest shares in structure of complex carcinogenic risks are made in food stuff and water consumption in structure of complex non-carcinogenic risks as a result of air pollution and food stuff pollution. Conclusions. Obtained data could be used to set priorities in preventive measures to preserve health of the population in industrial cities of the Krasnoyarsk region.

Heavy Metal Concentration in Black Tea in Iran

Directory of Open Access Journals (Sweden)

Nafiseh Yousefi

2017-03-01

Full Text Available Background & Aims of the Study: Tea is one of the most important beverages that consumes in several parts of the world including Iran. Tea plant can be contaminated during manufacturing processes and growth period by pollutants such as heavy metals. In this study, the concentration of some heavy metals in different brands of both Iranian and imported black tea to Iran was investigated to survey the human exposure to such pollutants. Materials & Methods: The study was carried out on different brands of black tea that most widely consume in Iran. The samples were collected from available supermarkets in Tehran city and concentrations of Mn, Cd and Cu were determined in black tea, using ICP-OES. Finally obtained results, by one way ANOVA analysis, compared to maximum contaminant concentration which is determined by WHO. Results: Results showed that concentrations of measured heavy metals in sampled black tea were different according to the brand of tea. The mean of Mn, Cu and Cd elements in all tea samples were 664.78, 26.15 and 0.194 µg/g, respectively. Generally, Cu content in studied samples was not significantly above WHO but Cd content, in some cases, was significantly higher than WHO. The guideline value is not given by WHO for Mn content of tea. Conclusions: According to the obtained results, Cd content is exceeding than WHO standards, therefore, control of Cd, as a toxic element that can accumulate in living systems, is necessary.

Heavy metal pollution of coal mine-affected agricultural soils in the northern part of Bangladesh.

Science.gov (United States)

Bhuiyan, Mohammad A H; Parvez, Lutfar; Islam, M A; Dampare, Samuel B; Suzuki, Shigeyuki

2010-01-15

Total concentrations of heavy metals in the soils of mine drainage and surrounding agricultural fields in the northern part of Bangladesh were determined to evaluate the level of contamination. The average concentrations of Ti, Mn, Zn, Pb, As, Fe, Rb, Sr, Nb and Zr exceeded the world normal averages and, in some cases, Mn, Zn, As and Pb exceeded the toxic limit of the respective metals. Soil pollution assessment was carried out using enrichment factor (EF), geoaccumulation index (I(geo)) and pollution load index (PLI). The soils show significant enrichment with Ti, Mn, Zn, Pb, As, Fe, Sr and Nb, indicating inputs from mining activities. The I(geo) values have revealed that Mn (1.24+/-0.38), Zn (1.49+/-0.58) and Pb (1.63+/-0.38) are significantly accumulated in the study area. The PLIs derived from contamination factors indicate that the distal part of the coal mine-affected area is the most polluted (PLI of 4.02). Multivariate statistical analyses, principal component and cluster analyses, suggest that Mn, Zn, Pb and Ti are derived from anthropogenic sources, particularly coal mining activities, and the extreme proximal and distal parts are heavily contaminated with maximum heavy metals.

Properties of particulate pollution in the port city of Valparaiso, Chile

Science.gov (United States)

Marín, Julio C.; Raga, Graciela B.; Arévalo, Jorge; Baumgardner, Darrel; Córdova, Ana M.; Pozo, Diana; Calvo, Ana; Castro, Amaya; Fraile, Roberto; Sorribas, Mar

2017-12-01

The city of Valparaiso is home to one of the largest commercial ports on the west coast of South America. Port activities, that continue year-round, 24 h a day and seven days a week, produce emissions of pollutants, particularly aerosol particles composed of black and brown carbon (BC and BrC) that have serious impact on human population and the local environment. A measurement program was launched to document the magnitude of selected pollutants, to identify their sources and to evaluate the meteorological processes that enhance and transport these pollutants locally and regionally. In this study, we report the measurements made during four months: 25July - 25August 2014 (referred to as August 2014 throughout the manuscript), December 2014, January 2015 and March 2015. The daily mass concentrations of equivalent black carbon (eBC), derived from measurements of the light absorption coefficient, regularly exceed 5 μg m-3, a magnitude similar to values found in megacities such as Mexico City. The daily maximum number concentration of condensation nuclei (CN) is usually larger than 30000 cm-3. The Angstrom absorption exponent (AAE), derived from the absorption coefficients at 550 nm and 870 nm, is used to identify the primary sources of BC and BrC. In colder weather, emissions from the diesel fueled buses and trucks and the consumption of kerosene and wood for residential heating are the main sources of BC. In December, local wildfires contributed to the particle mass loading, but the day-to-day variability in boundary layer height and the presence of clouds and fog in occasions inhibited high concentrations. In March, the port activities reach a yearly peak during the seasonal export of agricultural products that translates into much more ship and truck traffic leading to very high eBC concentrations, comparable to values observed during August. The variability in weather patterns underscores the complexity of meteorological processes that drive the evolution and

Development of Land Use Regression models for particulate matter and associated components in a low air pollutant concentration airshed

NARCIS (Netherlands)

Dirgawati, Mila; Heyworth, Jane S.; Wheeler, Amanda J.; McCaul, Kieran A.; Blake, David; Boeyen, Jonathon; Cope, Martin; Yeap, Bu Beng; Nieuwenhuijsen, Mark; Brunekreef, Bert|info:eu-repo/dai/nl/067548180; Hinwood, Andrea

2016-01-01

Perth, Western Australia represents an area where pollutant concentrations are considered low compared with international locations. Land Use Regression (LUR) models for PM10, PM2.5 and PM2.5 Absorbance (PM2.5Abs) along with their elemental components: Fe, K, Mn, V, S, Zn and Si were developed for

The persistence of pollutants in large lakes: the lessons from studies of radioactivity

International Nuclear Information System (INIS)

Edgington, D.N.

1986-01-01

Long-lived radionuclides such as 137 Cs and sup(239,240)Pu have proved useful tracers to study the movement of sediments in aquatic systems. Measurements of radionuclides in lakes have provided an understanding of the processes of transport and fate, and the means to estimate critical parameters to be included in models used to predict the persistence of pollutants in aquatic environments. The history of the delivery of these radionuclides to the surface waters of the Great Lakes is better known than other pollutants. Since data sets used to establish the present sedimentation models were established a decade ago, the predictive capability of these models can be tested by investigating the present distribution of these radionuclides in the lakes. Distribution patterns of sedimentation rate and 137 Cs deposition have not changed, and the subsurface peak in activity corresponding to the maximum input flux in the early 1960s has moved downward relative to the bottom of the biologically mixed layer. An assessment is made of average sedimentation rate and mixing depth to include a simple water quality model to predict the concentration of pollutants in water, i.e. coupling simple concentration-time models with the steady-state sedimentation-mixing model. (author)

Determination of heavy metal pollutants such as Hg, Zn, Se, Cd, and Cu in aquatic environment of Thana Creek by radiochemical thermal neutron activation analysis

International Nuclear Information System (INIS)

khan, S.Z.; Shah, P.K.; Ramani Rao, V.; Turel, Z.r.; Haldar, B.C.

1984-01-01

A rapid method has been developed for the radiochemical separation of Cu, As, Se, Hg, and Zn from thermal neutron irradiated environmental samples. The concentration of the elements in the environmental samples has been ascertained by radiochemical neutron activation analysis. The accuracy, precision and sensitivity of the method has been determined. The results of the analysis indicates the location of maximum pollution of the aquatic environment and the extent of pollution in the 5 locations of Thana Creek. 1 reference, 3 tables

Respiratory effects of commuters' exposure to air pollution in traffic.

Science.gov (United States)

Zuurbier, Moniek; Hoek, Gerard; Oldenwening, Marieke; Meliefste, Kees; van den Hazel, Peter; Brunekreef, Bert

2011-03-01

Much time is spent in traffic, especially during rush hours, when air pollution concentrations on roads are relatively high. Controlled exposure studies have shown acute respiratory effects of short, high exposures to air pollution from motor vehicles. Acute health effects of lower real-life exposures in traffic are unclear. Exposures of 34 healthy, nonsmoking adult volunteers were repeatedly measured while commuting for 2 hours by bus, car, or bicycle. Particle number (PN), particulate matter (PM2.5 and PM10), and soot exposures were measured. Lung function and airway resistance were measured directly before, directly following, and 6 hours after exposure. Exhaled nitric oxide (NO) was measured directly before and 6 hours after exposure. Inhaled doses were estimated based on monitored heart rates. Mixed models were used to analyze effects of exposure on changes in health parameters after exposure compared with before. PN, PM10, and soot were associated with decreased peak expiratory flow directly following but not 6 hours after exposure. PN doses were associated with decreases in maximum midexpiratory flow and forced expiratory flow (FEV1) 6 hours after exposure, whereas PN and soot exposures were associated with increased maximum midexpiratory flow and FEV1 directly after exposure. PN and soot were associated with increased exhaled NO after car and bus but not bicycle trips. PN was also associated with an increase in airway resistance directly following exposure but not 6 hours later. We found modest effects of 2-hour in-traffic exposure to air pollutants on peak flow, exhaled NO, and airway resistance.

Finite Difference Formulation for Prediction of Water Pollution

Science.gov (United States)

Johari, Hanani; Rusli, Nursalasawati; Yahya, Zainab

2018-03-01

Water is an important component of the earth. Human being and living organisms are demand for the quality of water. Human activity is one of the causes of the water pollution. The pollution happened give bad effect to the physical and characteristic of water contents. It is not practical to monitor all aspects of water flow and transport distribution. So, in order to help people to access to the polluted area, a prediction of water pollution concentration must be modelled. This study proposed a one-dimensional advection diffusion equation for predicting the water pollution concentration transport. The numerical modelling will be produced in order to predict the transportation of water pollution concentration. In order to approximate the advection diffusion equation, the implicit Crank Nicolson is used. For the purpose of the simulation, the boundary condition and initial condition, the spatial steps and time steps as well as the approximations of the advection diffusion equation have been encoded. The results of one dimensional advection diffusion equation have successfully been used to predict the transportation of water pollution concentration by manipulating the velocity and diffusion parameters.

Urban Mobility and Polluting Emissions: Impacts on Public Welfare

Directory of Open Access Journals (Sweden)

Romano Fistola

2009-07-01

Full Text Available This article introduces the problem of assessing urban effects of air pollution produced by road traffic and it is oriented to individualize the "critical" areas where it is necessary to intervene in order to optimize the security levels for public wellbeing. The research is targeted to assess the effects of pollutant emissions, particularly of PM10, on human health by testing methodology at three different territorial levels (regional, provincial, municipal. In this article we refer particularly to the city of Benevento and we propose to point out a methodology for identifying critical infrastructure where it is necessary to restrict vehicular traffic. The target of this study is the identification of urban ambit characterized by high levels of risk to public health arising from the mobility vehicle. Prerequisite is the consideration that the effects of pollutants are linked with urban morphology in particular the physical structure of the road network. In other word, within the city it is possible to identify "critical channels" where safety levels for human health are strongly compromise by their physical structure. The test has been referred to Benevento by using GIS to identify urban areas where high levels of risk due to pollutant emission concentrate. Gis has been projected to allow both the identification of “maximum risk areas” and the "critical channel" within the city.

Bioaccumulation of organic pollutants in Indo-Pacific humpback dolphin: A review on current knowledge and future prospects.

Science.gov (United States)

Sanganyado, Edmond; Rajput, Imran Rashid; Liu, Wenhua

2018-06-01

Indo-Pacific humpback dolphin (Sousa chinensis) are chronically exposed to organic pollutants since they inhabit shallow coastal waters that are often impacted by anthropogenic activities. The aim of this review was to evaluate existing knowledge on the occurrence of organic pollutants in Indo-Pacific humpback dolphins, identify knowledge gaps, and offer recommendations for future research directions. We discussed the trends in the bioaccumulation of organic pollutants in Indo-Pacific humpback dolphins focusing on sources, physicochemical properties, and usage patterns. Furthermore, we examined factors that influence bioaccumulation such as gender, age, dietary intake and tissue-specific distribution. Studies on bioaccumulation in Indo-Pacific humpback dolphin remain scarce, despite high concentrations above 13,000 ng/g lw we previously detected for PFOS, ∑PBDE and chlorinated paraffins. The maximum concentration of organochlorines detected was 157,000 ng/g wt. Furthermore, variations in bioaccumulation were shown to be caused by factors such as usage patterns and physicochemical properties of the pollutant. However, restrictions in sampling inhibit investigations on exposure pathway and toxicity of organic pollutants in Indo-Pacific humpback dolphin. We proposed the use of biopsy sampling, predictive bioaccumulation and toxicity modeling, and monitoring other emerging contaminants such as microplastics and pharmaceuticals for future health risk assessment on this critically endangered marine mammal species. Copyright © 2018 Elsevier Ltd. All rights reserved.

Introduction to pollution and biology

Energy Technology Data Exchange (ETDEWEB)

Horita, Y

1972-01-01

The mechanism of photosynthesis, environmental conditions, and the chemical and biological significance of photosynthetic bacteria are discussed. Photosynthetic bacteria, which are extremely useful and important in the ecological system, can become a cause of pollution when excessively proliferated. The idea that pollution could be solved by planting vegetation is also a misconcept. Carbon dioxide is not the major source of pollution, and local increases of CO/sub 2/ partial pressure do not affect the environment in general. More important, green plants are sensitive to air pollutants and react faster than any other living things to pollutants such as fluorides, nitrate, ozone, peroxyacetyl nitrate, and sulfur dioxide. Only 1-3% of solar energy is used for photosynthesis. The use must be increased to maximum by effective planning of plant formation, density, and arrangements. Through genetic studies, production and proliferation of useful plants should be planned and developed. Pollution control must be programmed ecologically, suitable ecological systems must be developed in various geographical areas, in addition to the effort to eliminate pollution sources.

Modeling extreme PM10 concentration in Malaysia using generalized extreme value distribution

Science.gov (United States)

Hasan, Husna; Mansor, Nadiah; Salleh, Nur Hanim Mohd

2015-05-01

Extreme PM10 concentration from the Air Pollutant Index (API) at thirteen monitoring stations in Malaysia is modeled using the Generalized Extreme Value (GEV) distribution. The data is blocked into monthly selection period. The Mann-Kendall (MK) test suggests a non-stationary model so two models are considered for the stations with trend. The likelihood ratio test is used to determine the best fitted model and the result shows that only two stations favor the non-stationary model (Model 2) while the other eleven stations favor stationary model (Model 1). The return level of PM10 concentration that is expected to exceed the maximum once within a selected period is obtained.

Atmospheric pollution over the eastern Mediterranean during summer - a review

Science.gov (United States)

Dayan, Uri; Ricaud, Philippe; Zbinden, Régina; Dulac, François

2017-11-01

3 over the EM were found to be 2 to 10 times higher than in the hemispheric background troposphere. Several factors favor sulfate particulate abundance over the EM. Models, aircraft measurements, and satellite-derived data have clearly shown that sulfate has a maximum during spring and summer over the EM. The carbon monoxide (CO) seasonal cycle, as obtained from global background monitoring sites in the EM, is mostly controlled by the tropospheric concentration of the hydroxyl radical (OH) and therefore demonstrates high concentrations over winter months and the lowest concentrations during summer when photochemistry is active. Modeling studies have shown that the diurnal variations in CO concentration during the summer result from long-range CO transport from European anthropogenic sources, contributing 60 to 80 % of the boundary-layer CO over the EM. The values retrieved from satellite data enable us to derive the spatial distribution of methane (CH4), identifying August as the month with the highest levels over the EM. The outcomes of a recent extensive examination of the distribution of methane over the tropospheric Mediterranean Basin, as part of the Chemistry-Aerosol Mediterranean Experiment (ChArMEx) program, using model simulations and satellite measurements, are coherent with other previous studies. Moreover, this methane study provides some insight into the role of the Asian monsoon anticyclone in controlling the variability of CH4 pollutant within mid-to-upper tropospheric levels above the EM in summer.

Runoff quality and pollution loadings from a tropical urban catchment.

Science.gov (United States)

Yusop, Z; Tan, L W; Ujang, Z; Mohamed, M; Nasir, K A

2005-01-01

Runoff quality draining from 17.14 km2 urban catchment in Johor Bahru, Malaysia, was analysed. The land-use consists of residential (30.3%), agricultural (27.3%), open space (27.9%), industrial (8.1%) and commercial (6.4%) areas. Three storm events were sampled in detail. These storms produced stormflow between 0.84 mm and 27.82 mm, and peakflow from 2.19 m3/s to 42.36 m3/s. Water quality showed marked variation during storms especially for TSS, BOD and COD with maximum concentrations of 778 mg/l, 135 mg/l and 358 mg/l, respectively. Concentrations of TOC, DOC, NH3-N, Fe and level of colour were also high. In general, the river quality is badly polluted and falls in Class V based on the Malaysian Interim National Water Quality Standards. Event Mean Concentrations (EMC) for various parameters varied considerably between storms. The largest storm produced higher EMC for TSS, NO3-N and SS whereas the smaller storms tend to register higher EMC for BOD, COD, NH3-N, TOC, Ca, K, Mg, Fe and Zn. Such variations could be explained in terms of pollutant availability and the effects of flushing and dilution. Based on a three-month average recurrence interval (ARI) of rainfall, the estimated event loadings (ton/ha) of TSS, BOD, COD, TOC, NH3-N and NO3-N were 0.055, 0.016, 0.012, 0.039, 0.010, 0.0007 and 0.0002, respectively. Heavy metals present in trace quantities. Storms with 3 months ARI could capture about 70% of the total annual loads of major pollutants.

Air pollution and respiratory infection in children

Energy Technology Data Exchange (ETDEWEB)

Douglas, J W.B.; Waller, R E

1966-01-01

Air pollution, as estimated by domestic coal consumption was categorized into 4 groups; very low, low, moderate, and high. The predicted pollution categories were later compared with measured smoke and SO/sub 2/ concentrations and found to be as expected. The smoke concentration was found to be 67, 138, 217, and 281 ..mu..g/m/sup 3/ while the SO/sub 2/ concentration was 90, 130, 191, and 257 ..mu..g/m/sup 3/ in the very low, low, moderate, and high pollution groups respectively. These values excluded the greater London area which had somewhat lower smoke but similar SO/sub 2/ concentrations. The air pollution had no effect on upper-respiratory illness in British children but had a highly significant effect on lower-respiratory illness. The percent of children experiencing the first lower-respiratory tract infection during the first 9 months of life in the 4 pollution groups were 7.2 in the very low, 11.4 in the low, 16.5 in the moderate and 17.1 in the high.

Use of pre-industrial floodplain lake sediments to establish baseline river metal concentrations downstream of Alberta oil sands: a new approach for detecting pollution of rivers

International Nuclear Information System (INIS)

Wiklund, Johan A; Hall, Roland I; Farwell, Andrea J; George Dixon, D; Wolfe, Brent B; Edwards, Thomas WD

2014-01-01

In the Alberta oil sands region, insufficient knowledge of pre-disturbance reference conditions has undermined the ability of the Regional Aquatics Monitoring Program (RAMP) to detect pollution of the Athabasca River, because sampling began three decades after the industry started and the river naturally erodes oil-bearing strata. Here, we apply a novel approach to characterize pre-industrial reference metal concentrations in river sediment downstream of Alberta oil sands development by analyzing metal concentrations in sediments deposited in floodplain lakes of the Athabasca Delta during 1700–1916, when they were strongly influenced by Athabasca River floodwaters. We compared results to metal concentrations in surficial bottom sediments sampled by RAMP (2010–2013) at downstream sites of the Athabasca River and distributaries. When normalized to lithium content, concentrations of vanadium (a metal of concern in the oil sands region) and other priority pollutants (Be, Cd, Cr, Cu, Pb, Ni, Zn) in nearly all of the RAMP river sediment samples lie below the upper 95% prediction interval linearly extrapolated from the river-derived lake sediments. Assuming the RAMP protocols obtained recently deposited sediment, this indicates that the metal concentrations in downstream Athabasca River sediment have not increased above pre-disturbance levels. Reference conditions derived from the lake sediment data were used to develop profiles of metal residual concentrations versus time for the RAMP river sediment data, which provides an excellent tool for decision-makers to identify and quantify levels of metal pollution for any given sample, and to monitor for future trends. We recommend that the approach be applied to resurrect the utility of RAMP data at other river sampling locations closer to the development, and for ongoing risk assessment. The approach is also readily transferable to other rivers where insufficient pre-disturbance reference data impairs an ability to

Total and available heavy metal concentrations in soils of the Thriassio plain (Greece) and assessment of soil pollution indexes.

Science.gov (United States)

Massas, Ioannis; Kalivas, Dionisios; Ehaliotis, Constantions; Gasparatos, Dionisios

2013-08-01

The Thriassio plain is located 25 km west of Athens city, the capital of Greece. Two major towns (Elefsina and Aspropyrgos), heavy industry plants, medium to large-scale manufacturing, logistics plants, and agriculture comprise the main land uses of the studied area. The aim of the present study was to measure the total and available concentrations of Cr, Zn, Ni, Pb, Co, Mn, Ba, Cu, and Fe in the top soils of the plain, and to asses soil contamination by these metals by using the geoaccumulation index (I geo), the enrichment factor (EF), and the availability ratio (AR) as soil pollution indexes. Soil samples were collected from 90 sampling sites, and aqua regia and DTPA extractions were carried out to determine total and available metal forms, respectively. Median total Cr, Zn, Ni, Pb, Co, Mn, Ba, Cu, and Fe concentrations were 78, 155, 81, 112, 24, 321, 834, 38, and 16 × 10(3) mg kg(-1), respectively. The available fractions showed much lower values with medians of 0.4, 5.6, 1.7, 6.9, 0.8, 5.7, 19.8, 2.1, and 2.9 mg kg(-1). Though median total metal concentrations are not considered as particularly high, the I geo and the EF values indicate moderate to heavy soil enrichment. For certain metals such as Cr, Ni, Cu, and Ba, the different distribution patterns between the EFs and the ARs suggest different origin of the total and the available metal forms. The evaluation of the EF and AR data sets for the soils of the two towns further supports the argument that the EFs can well demonstrate the long-term history of soil pollution and that the ARs can adequately portray the recent history of soil pollution.

TRENDS IN ESTIMATED MIXING DEPTH DAILY MAXIMUMS

Energy Technology Data Exchange (ETDEWEB)

Buckley, R; Amy DuPont, A; Robert Kurzeja, R; Matt Parker, M

2007-11-12

Mixing depth is an important quantity in the determination of air pollution concentrations. Fireweather forecasts depend strongly on estimates of the mixing depth as a means of determining the altitude and dilution (ventilation rates) of smoke plumes. The Savannah River United States Forest Service (USFS) routinely conducts prescribed fires at the Savannah River Site (SRS), a heavily wooded Department of Energy (DOE) facility located in southwest South Carolina. For many years, the Savannah River National Laboratory (SRNL) has provided forecasts of weather conditions in support of the fire program, including an estimated mixing depth using potential temperature and turbulence change with height at a given location. This paper examines trends in the average estimated mixing depth daily maximum at the SRS over an extended period of time (4.75 years) derived from numerical atmospheric simulations using two versions of the Regional Atmospheric Modeling System (RAMS). This allows for differences to be seen between the model versions, as well as trends on a multi-year time frame. In addition, comparisons of predicted mixing depth for individual days in which special balloon soundings were released are also discussed.

Assessment of socio-economic consequences of the Commission's thematic strategy for air pollution

International Nuclear Information System (INIS)

Bach, H.; Skou Andersen, M.; Illerup, J.B.

2006-01-01

The Commission has presented a thematic strategy on air pollution and has completed an Impact Assessment, which describes the costs and benefits for the member states. The thematic strategy is to result in a revised air quality directive as well as a revised NEC-directive that determines maximum emissions for a number of air pollution components, the so-called emission ceilings. The air pollution components include sulphur dioxide (SO 2 ), nitrogen oxide (NO X ), volatile organic compounds (NMVOC), ammonia (NH 3 ) and particulate matters (PM 2,5 ). The thematic strategy draws up targets for reductions of the Danish emissions for these components, which have to be met by 2020. These reductions will contribute to a lowering of PM 2,5 concentrations both in Denmark and in neighbouring countries. The concentration of PM 2,5 in the air includes both primary particles that come from emission of particles from e.g. incineration processes, and so-called secondary particles that are generated from emissions of NO X , SO 2 and NH 3 , and from releases from e.g. vegetation. A very large part of the secondary particles in the air in Denmark stems from emissions of these components in the rest of Europe. A very important condition for a reduction in the concentration of PM 2,5 in the air is thus a reduction of the emissions of these components in all of Europe. (au)

Ambient Air Pollutants Have Adverse Effects on Insulin and Glucose Homeostasis in Mexican Americans

Science.gov (United States)

Chen, Zhanghua; Salam, Muhammad T.; Toledo-Corral, Claudia; Watanabe, Richard M.; Xiang, Anny H.; Buchanan, Thomas A.; Habre, Rima; Bastain, Theresa M.; Lurmann, Fred; Wilson, John P.; Trigo, Enrique

2016-01-01

OBJECTIVE Recent studies suggest that air pollution plays a role in type 2 diabetes (T2D) incidence and mortality. The underlying physiological mechanisms have yet to be established. We hypothesized that air pollution adversely affects insulin sensitivity and secretion and serum lipid levels. RESEARCH DESIGN AND METHODS Participants were selected from BetaGene (n = 1,023), a study of insulin resistance and pancreatic β-cell function in Mexican Americans. All participants underwent DXA and oral and intravenous glucose tolerance tests and completed dietary and physical activity questionnaires. Ambient air pollutant concentrations (NO2, O3, and PM2.5) for short- and long-term periods were assigned by spatial interpolation (maximum interpolation radius of 50 km) of data from air quality monitors. Traffic-related air pollution from freeways (TRAP) was estimated using the dispersion model as NOx. Variance component models were used to analyze individual and multiple air pollutant associations with metabolic traits. RESULTS Short-term (up to 58 days cumulative lagged averages) exposure to PM2.5 was associated with lower insulin sensitivity and HDL-to-LDL cholesterol ratio and higher fasting glucose and insulin, HOMA-IR, total cholesterol, and LDL cholesterol (LDL-C) (all P ≤ 0.036). Annual average PM2.5 was associated with higher fasting glucose, HOMA-IR, and LDL-C (P ≤ 0.043). The effects of short-term PM2.5 exposure on insulin sensitivity were largest among obese participants. No statistically significant associations were found between TRAP and metabolic outcomes. CONCLUSIONS Exposure to ambient air pollutants adversely affects glucose tolerance, insulin sensitivity, and blood lipid concentrations. Our findings suggest that ambient air pollutants may contribute to the pathophysiology in the development of T2D and related sequelae. PMID:26868440

Analysis of arsenic pollution in groundwater aquifers by X-ray fluorescence

International Nuclear Information System (INIS)

Sbarato, V.M.; Sanchez, H.J.

2001-01-01

The serious contamination of groundwater in the southeastern plain of the province of Cordoba (Argentina), a phenomenon mentioned in the literature for over 80 years, has given rise to this initial hydrologic study covering an area over 250 km 2 . This study analyzes a rural area near a little town called La Francia, and is motivated by the existence of an important pollution with arsenic in the first-aquifer groundwater of the region. This phenomenon has been mentioned for a long time and evidenced by the high incidence of diseases associated with this element in the local population. By means of the X-ray fluorescence (XRF) technique, and using an energy-dispersive spectrometer, 50 samples of groundwater of the rural zone of La Francia from about 100 m deep (second aquifer), were analyzed. The samples were excited with a 3 kW X-ray tube and measured using a reflecting geometry with 45 deg. of incident and take-off directions. Preconcentration techniques for the preparation of the samples were employed in order to obtain an adequate signal-to-noise ratio. The As concentration in water was obtained using calibration curves and the internal standard method for quantification. A high percentage of the analyzed samples showed concentrations lesser than or equal to 0.05 mg l -1 . This value corresponds to the maximum pollutant level for humans. The maximum measured value reaches 3 mg l -1 in samples collected in perforations of first-aquifer wells and in some second-aquifer isolated wells

THE EFFECT OF IRRADIATION DOSE AND AMMONIA CONCENTRATION ON THE APPLICATION OF ELECTRON BEAM FOR TREATMENT GASES POLLUTION OF SO2AND NOX

Directory of Open Access Journals (Sweden)

Erizal Erizal

2010-06-01

Full Text Available The application of electron beam for treatment gases pollution of SO2 and NOx has been studied.  The simulated SO2 and NOx gases stream produced from diesel fuel burning boiler were flown into electron beam chamber. Irradiation was conducted using 1000 keV electron beam machine at the dose up to 8.8 kGy, while   water vapour and the ammonia gas with variation concentration flew into the system during irradiation. The concentrations of the gases change were observed during processes. After evaluation, it was found that by increasing irradiation dose, the concentration of SO2 and NOx gases removal increases.  The efficiency of gases removal may reach 98 % for SO2 and 88 % for NOX at a dose of 8.8 kGy. By increasing ammonia concentration, the efficiency gas removal increases. Besides, by-products from the irradiation yield were sulfate and nitrate salt compound which are possible to be used as a fertilizer.      Keywords: radiation, electron beam, gas pollution, SO2, NOx, ammonia

40 CFR Table C-1 to Subpart C of... - Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specification

Science.gov (United States)

2010-07-01

... Measurements Required, and Maximum Discrepancy Specification C Table C-1 to Subpart C of Part 53 Protection of... Reference Methods Pt. 53, Subpt. C, Table C-1 Table C-1 to Subpart C of Part 53—Test Concentration Ranges..., June 22, 2010, table C-1 to subpart C was revised, effective Aug. 23, 2010. For the convenience of the...

Assessment of regional air pollution variability in Istanbul

International Nuclear Information System (INIS)

Sen, Z.; Oztopal, A.

2001-01-01

Air pollution concentrations have temporal and spatial variations depending on the prevailing weather conditions, topographic features, city building heights and locations. When the measurements of air pollutants are available at set measurement sites, the regional variability degree of air pollutants is quantified using the point cumulative semi-variogram (PCSV). This technique provides a systematic method for calculating the changes in the concentrations of air pollutants with distance from a specific site. Regional variations of sulphur dioxide (SO 2 ) and total suspended particulate (TSP) matter concentrations in Istanbul city were evaluated using the PCSV concept. The data were available from 16 different air pollution measurement stations scattered all over the city for a period from 1988 to 1994. Monthly regional variation maps were drawn in and around the city at different radii of influence. These maps provide a reference for measuring future changes of air pollution in the city. (author)

Atmospheric concentrations of 7Be and 210Pb in Granada, Spain

International Nuclear Information System (INIS)

Azahra, M.; Gonzalez-Gomez, C.; Instituto Andaluz de Ciencias de la Tierra, Granada; Lopez-Penalver, J.J.; Camacho-Garcia, M.A.; El Bardouni, T.; Boukhal, H.

2004-01-01

Aerosols samples in near-surface air of Granada (Spain) were collected on a weekly basis. The seasonal 210 Pb and 7 Be concentrations were determined during the five-year period, from October 1993 to September 1997. The elements, despite their different origin and their different distribution throughout the atmosphere, present the same seasonal variation. There was a tendency for a maximum during the summer season and a minimum during fall and/or winter. Concentration of 7 Be and 210 Pb and meteorological data have been used in order to determine the periods of the potential radioactive pollution. Deposition of 7 Be occurs primarily by precipitation except during the investigation periods where precipitation was scarce and irregular. (author)

The impact of the "Air Pollution Prevention and Control Action Plan" on PM2.5 concentrations in Jing-Jin-Ji region during 2012-2020.

Science.gov (United States)

Cai, Siyi; Wang, Yangjun; Zhao, Bin; Wang, Shuxiao; Chang, Xing; Hao, Jiming

2017-02-15

In order to cope with heavy haze pollution in China, the Air Pollution Prevention and Control Action Plan including phased goals of the fine particulate matter (PM 2.5 ) was issued in 2013. In this study, China's emission inventories in the baseline 2012 and the future scenarios of 2017 and 2020 have been developed based on this Action Plan. Beijing-Tianjin-Hebei (Jing-Jin-Ji) region, one of the most polluted regions in China, was taken as a case to assess the impact of phased emission control measures on PM 2.5 concentration reduction using WRF-CMAQ model system. With the implementation of the Action Plan, the emissions of sulfur dioxide (SO 2 ), nitrogen oxides (NO X ) , PM 2.5 , non-methane volatile organic compound (NMVOC), and ammonia (NH 3 ) in 2017 will decrease by36%, 31%, 30%,12%, and -10% from the 2012 levels in Jing-Jin-Ji, respectively. In 2020, the emissions of SO 2 , NO X, PM 2.5 , NMVOC, and NH 3 will decrease by 40%, 44%, 40%, 22%, and -3% from the 2012 levels in Jing-Jin-Ji, respectively. Consequently, the ambient annual PM 2.5 concentration under the scenarios of 2017 and 2020 will be 28.3% and 37.8% lower than those in 2012, respectively. The Action Plan provided an effective approach to alleviate PM 2.5 pollution level in Jing-Jin-Ji region. However, emission control of NMVOC and NH 3 should be paid more attention and be strengthened in future. Meanwhile, emission control of NO x , SO 2 , NH 3 and NMVOC synergistically are highly needed in the future because multiple pollutants impact on PM 2.5 and O 3 concentrations nonlinearly. Copyright © 2016 Elsevier B.V. All rights reserved.

Synthesis report: program ecosystems, transport, pollutions, 1998 - 2001; Rapport de synthese: programme ecosystemes, transport, pollutions, 1998 - 2001

Energy Technology Data Exchange (ETDEWEB)

Etchelecou, A; Deletraz, G; Elichegaray, Ch

2001-04-01

The ''Ecosystems, Transports, Pollution Program'' ETP Program, has been elaborated to evaluate the road pollution impacts on the mountain ecosystems. Four mountains valleys have been chosen: two in Alps (Chamonix and Maurienne) and two in Pyrenees (Biriatou and Vallee d'Aspe). This Program presents six objectives: the road traffic characterization, the pollutants emission estimation, the pollutants concentrations in the air, the pollutants dispersion according to relief, the relationships between pollutants emissions and bio-monitoring, the road pollution effects on nearby ecosystems. (A.L.B.)

Analysis of local scale tree-atmosphere interaction on pollutant concentration in idealized street canyons and application to a real urban junction

NARCIS (Netherlands)

Buccolieri, R.; Salim, S.M.; Leo, L.S.; Sabatino, Di S.; Chan, A.; Ielpo, P.; Gennaro, de G.; Gromke, C.B.

2011-01-01

This paper first discusses the aerodynamic effects of trees on local scale flow and pollutant concentration in idealized street canyon configurations by means of laboratory experiments and Computational Fluid Dynamics (CFD). These analyses are then used as a reference modelling study for the

Concentrations of benzene and toluene in the atmosphere of the southwestern area at the Mexico City Metropolitan Zone

Energy Technology Data Exchange (ETDEWEB)

Bravo, H.; Sosa, R.; Sanchez, P. [Universidad Autonoma de Mexico, Ciudad Universitaria (Mexico). Centro de Ciencias de la Atmosfera; Bueno, E.; Gonzalez, L. [Centro Nacional de Investigacion y Capacitacion Ambiental, Instituto Nacional de Ecologia, SEMARNAP, Mexico (Mexico)

2002-08-01

The Mexico City Metropolitan Zone (MCMZ) presents important emissions of hazardous air pollutants. It is well documented that the MCMZ suffers a critical air pollution problem due to high ozone and particulate matter concentrations. However, toxic air pollutants such as benzene and toluene have not been considered. Benzene has accumulated sufficient evidence as a human carcinogen, and the ratio benzene/toluene is an excellent indicator to evaluate control strategies efficiency. In order to evaluate the levels of these two air toxic pollutants in the MCMZ, ambient air samples were collected in canisters and analyzed with a gas chromatograph with a flame ionization detector, according to procedures described in the United States Environmental Protection Agency (USEPA) method TO-15. Quality assurance was performed collecting duplicate samples which were analyzed in replicate to quantify the precision of air-quality measurements. Three different sites located in the Southwestern area in the MCMZ were selected for the sampling: the University campus, a gas station, and a vertical condominium area, in the same neighborhood, which presents different activities. At these sites, grab air samples were collected during the morning hours (7-8 a.m.), while for the University area, 24 h integrated air samples were collected simultaneously, with grab samples. Benzene concentrations (24 h sampling) in the atmosphere around the University campus have similar present levels as in other cities of North America. Mean values in this site were about 1.7 ppb. A significant variation exists between the benzene and toluene concentrations in the studied sites, being the more critical values than those registered at the gas station (an average of 25.8 ppb and a maximum of 141 ppb of benzene). There is a fuel regulation for gasoline in Mexico, which allows a maximum of 1 percent of benzene. However, since more than 60 percent of vehicles do not have catalytic converters (models before 1991

Concentrations, Deposition, and Effects of Nitrogenous Pollutants in Selected California Ecosystems

Directory of Open Access Journals (Sweden)

Andrzej Bytnerowicz

2001-01-01

Full Text Available Atmospheric deposition of nitrogen (N in California ecosystems is ecologically significant and highly variable, ranging from about 1 to 45 kg/ha/year. The lowest ambient concentrations and deposition values are found in the eastern and northern parts of the Sierra Nevada Mountains and the highest in parts of the San Bernardino and San Gabriel Mountains that are most exposed to the Los Angeles air pollution plume. In the Sierra Nevada Mountains, N is deposited mostly in precipitation, although dry deposition may also provide substantial amounts of N. On the western slopes of the Sierra Nevada, the majority of airborne N is in reduced forms as ammonia (NH3 and particulate ammonium (NH4+ from agricultural activities in the California Central Valley. In southern California, most of the N air pollution is in oxidized forms as nitrogen oxides (NOx, nitric acid (HNO3, and particulate nitrate (NO3– resulting from fossil fuel combustion and subsequent complex photochemical reactions. In southern California, dry deposition of gases and particles provides most (up to 95% of the atmospheric N to forests and other ecosystems. In the mixed-conifer forest zone, elevated deposition of N may initially benefit growth of vegetation, but chronic effects may be expressed as deterioration of forest health and sustainability. HNO3 vapor alone has a potential for toxic effects causing damage of foliar surfaces of pines and oaks. In addition, dry deposition of predominantly HNO3 has lead to changes in vegetation composition and contamination of ground- and stream water where terrestrial N loading is high. Long-term, complex interactions between N deposition and other environmental stresses such as elevated ozone (O3, drought, insect infestations, fire suppression, or intensive land management practices may affect water quality and sustainability of California forests and other ecosystems.

Radioactive pollution in Athens, Greece due to the Fukushima nuclear accident

International Nuclear Information System (INIS)

Kritidis, P.; Florou, H.; Eleftheriadis, K.; Evangeliou, N.; Gini, M.; Sotiropoulou, M.; Diapouli, E.; Vratolis, S.

2012-01-01

As a result of the nuclear accident in Fukushima Dai-ichi power plant, which started on March 11, 2011, radioactive pollutants were transferred by air masses to various regions of the Northern hemisphere, including Europe. Very low concentrations of 131 I, 137 Cs and 134 Cs in airborne particulate matter were measured in Athens, Greece during the period of March 24 to April 28, 2011. The maximum air concentration of 131 I was measured on April 6, 2011 and equaled 490 ± 35 μBq m −3 . The maximum values of the two cesium isotopes were measured on the same day and equaled 180 ± 40 μBq m −3 for 137 Cs and 160 ± 30 μBq m −3 for 134 Cs. The average activity ratio of 131 I/ 137 Cs in air was 3.0 ± 0.5, while the corresponding ratio of 137 Cs/ 134 Cs equaled 1.1 ± 0.3. No artificial radionuclides could be detected in air after April 28, 2011. Traces of 131 I as a result of radioactive deposition were measured in grass, soil, sheep milk and meat. The total deposition of 131 I (dry + wet) was 34 ± 4 Bq m −2 , and of 137 Cs was less than 10 Bq m −2 . The maximum concentration of 131 I in grass was 2.1 ± 0.4 Bg kg −1 , while 134 Cs was not detected. The maximum concentrations of 131 I and 137 Cs in sheep milk were 1.7 ± 0.16 Bq kg −1 and 0.6 ± 0.12 Bq kg −1 respectively. Concentrations of 131 I up to 1.3 ± 0.2 Bq kg −1 were measured in sheep meat. Traces of 131 I were found in a number of soil samples. The radiological impact of the Fukushima nuclear accident in Athens region was practically negligible, especially as compared to that of the Chernobyl accident and also to that of natural radioactivity.

Decontamination of Heavy Metals in Polluted Soil by Phytoremediation Using Bryophyllum Pinnatum

Directory of Open Access Journals (Sweden)

Ekwumemgbo P. A.

2013-04-01

Full Text Available Phytoremediation is the use of specially selected or engineered living green plants for in situ risk reduction and/or removal of pollutants from contaminated media. This process is one of the most rapidly developing components of environmentally friendly (green and cost-effective technology to abate environmental pollution. The risk reduction could be through the process of removal, degradation, containment of a contaminant or a combination of any of these factors. Bryophyllum pinnatum a herbally-accepted plant in some parts of the world was cultivated in ten different plastic buckets containing heavy metal polluted soil and nurtured for 20 months. The plants were left in ambient conditions and watered periodically. After the first 2 weeks, the plant and soil samples were collected and analysed for total concentration of Cd, Cr, Cu, Ni, Pb V and Zn. Subsequently, the plant and soil samples were collected monthly and analysed for the total concentrations of these heavy metals, using Atomic Absorption Spectrophotometry. Maximum extracted heavy metals from soil by plant were Cd (3.12±1.03 mg/kg, Cr (32.48±3.21 mg/kg, Cu (81.01±2.3 mg/kg Ni (11.91±2.32 mg/kg, Pb (399.90 ±4.32 mg/kg V (5.81±0.08 mg/kg and Zn (150.51± 0.33 and this occurred in the 4th month of study. This study confirms B. pinnatum as one of the plants that could be employed in phytoremediation of soil polluted by heavy metals.

Study of atmospheric pollution scavenging. Eighteenth progress report

Energy Technology Data Exchange (ETDEWEB)

Semonin, R.G.; Bartlett, J.D.; Bowersox, V.C.; Gatz, D.F.; Naiman, D.Q.; Peden, M.E.; Stahlhut, R.K.; Stensland, G.J.

1980-07-01

The analysis of aerosol samples obtained in rural east-central Illinois reveals a seasonal maximum in SO/sub 4/ during May to July and a similar pattern for NH/sub 4/. The annual median SO/sub 4/ is about 1 to 1.5 ..mu..g/m/sup 3/. In contrast to these ions, NO/sub 3/ displays highest values in the cold season. Soil-related species (Ca, K) seem to maximize in relation to farm tillage and harvesting practices. The NO/sub 3/ in recent precipitation samples over the northeast US increased between 1 and 2 times the values observed in the mid-1950's. A case study from SCORE-78 suggests that all ion concentrations analyzed from sequentially collected samples decreased from the onset of rain to a minimum corresponding to the heaviest rain rates. Four groups of elements in 10 event rain samples were identified using factor analysis. The groups include soluble and insoluble crustal elements, soluble pollutant metals and sulfate, and insoluble pollutant metals. Utilizing the factor analysis approach, the St. Louis METROMEX precipitation chemistry data showed that the SO/sub 4/ deposition patterns group consistently with those of other soluble pollutants. Additional factor analysis efforts on the St. Louis rainwater data set revealed that soluble and insoluble concentrations of a given element have different deposition patterns suggesting that scavenging and/or precipitation formation processes dictate the patterns. An approach to managing the vast data base of rain chemistry used in the above studies is described. The software also examines the data for certain aspects of quality assurance. The procedures used to analyze ambient air filter samples are discussed.

The intake of water containing a mix of pollutants at environmentally relevant concentrations leads to defensive response deficit in male C57Bl/6J mice.

Science.gov (United States)

de Souza, Joyce Moreira; Rabelo, Letícia Martins; de Faria, Denise Braga Gomes; Guimarães, Abraão Tiago Batista; da Silva, Wellington Alves Mizael; Rocha, Thiago Lopes; Estrela, Fernanda Neves; Chagas, Thales Quintão; de Oliveira Mendes, Bruna; Malafaia, Guilherme

2018-07-01

Previous studies have individually confirmed the toxic effects from different pollutants on mammals. However, effects resulting from the exposure of these animals to multi-pollutant mixes have not been studied so far. Thus, the aim of the current study is to assess the effect from the chronic exposure (105days) of C57Bl/6J mice to a mix of pollutants on their response to potential predators. In order to do so, the following groups were formed: "control", "Mix 1× [compounds from 15 pollutants identified in surface waters at environmentally relevant concentration (ERC)]", "Mix 10×" and "Mix 25×" (concentrations 10 and 25 times higher than the ERC). From the 100th experimental day on, the animals were subjected to tests in order to investigate whether they showed locomotor, visual, olfactory and auditory changes, since these abilities are essential to their anti-predatory behavior. Next, the animals' behavior towards potential predators (Felis catus and Pantherophis guttatus) was assessed. The herein collected data did not show defensive response from any of the experimental groups to the predatory stimulus provided by P. guttatus. However, the control animals, only, presented anti-predatory behavior when F. catus was introduced in the apparatus, fact that suggests defensive response deficit resulting from the treatments. Thus, the current study is pioneer in showing that the chronic intake of water containing a mix of pollutants (even at low concentrations) leads to behavioral disorders able to affect the survival and population dynamics of mammalian species at ecological level. Copyright © 2018 Elsevier B.V. All rights reserved.

Synthesis report: program ecosystems, transport, pollutions, 1998 - 2001; Rapport de synthese: programme ecosystemes, transport, pollutions, 1998 - 2001

Energy Technology Data Exchange (ETDEWEB)

Etchelecou, A.; Deletraz, G.; Elichegaray, Ch

2001-04-01

The ''Ecosystems, Transports, Pollution Program'' ETP Program, has been elaborated to evaluate the road pollution impacts on the mountain ecosystems. Four mountains valleys have been chosen: two in Alps (Chamonix and Maurienne) and two in Pyrenees (Biriatou and Vallee d'Aspe). This Program presents six objectives: the road traffic characterization, the pollutants emission estimation, the pollutants concentrations in the air, the pollutants dispersion according to relief, the relationships between pollutants emissions and bio-monitoring, the road pollution effects on nearby ecosystems. (A.L.B.)

Comparing ordinary kriging and inverse distance weighting for soil as pollution in Beijing.

Science.gov (United States)

Qiao, Pengwei; Lei, Mei; Yang, Sucai; Yang, Jun; Guo, Guanghui; Zhou, Xiaoyong

2018-06-01

Spatial interpolation method is the basis of soil heavy metal pollution assessment and remediation. The existing evaluation index for interpolation accuracy did not combine with actual situation. The selection of interpolation methods needs to be based on specific research purposes and research object characteristics. In this paper, As pollution in soils of Beijing was taken as an example. The prediction accuracy of ordinary kriging (OK) and inverse distance weighted (IDW) were evaluated based on the cross validation results and spatial distribution characteristics of influencing factors. The results showed that, under the condition of specific spatial correlation, the cross validation results of OK and IDW for every soil point and the prediction accuracy of spatial distribution trend are similar. But the prediction accuracy of OK for the maximum and minimum is less than IDW, while the number of high pollution areas identified by OK are less than IDW. It is difficult to identify the high pollution areas fully by OK, which shows that the smoothing effect of OK is obvious. In addition, with increasing of the spatial correlation of As concentration, the cross validation error of OK and IDW decreases, and the high pollution area identified by OK is approaching the result of IDW, which can identify the high pollution areas more comprehensively. However, because the semivariogram constructed by OK interpolation method is more subjective and requires larger number of soil samples, IDW is more suitable for spatial prediction of heavy metal pollution in soils.

Environment and Pollution Management of Pollution Volatile Organic Compounds in Cluj-Napoca

Directory of Open Access Journals (Sweden)

Carmen Florean

2016-10-01

Full Text Available Pollution negative influences the environmental, human health, buildings and increase the production of waste. We are currently witnessing pollution and degradation in some cases irreversible, of the environment. Environmental issues are extremely complex and cover all sectors. Worldwide, industrial pollution strategies necessary to reduce emissions to the atmosphere hydrocarbons, volatile organic compounds (VOCs and other polluants in urban areas. The highest concentrations of volatile organic compounds of more than 80 mg/m3 occur in densely populated areas. The latest data reported in the residential area of Cluj-Napoca values did not exceed 20 m /m3. However peaks reported VOC concentrations, depending on the season, exceeding the upper limit that according to Law. 104/2011 is 75 μ/m3. It was identified due to increase annual mean concentration of VOCs as, in particular, road traffic exceeding sanitary standards on the main traffic routes within the city. In this paper the results obtained after carrying out an analysis of the average VOC concentration recorded in the city Cluj-Napoca as a result of car traffic. They were pursued average concentrations of VOCs resulting from the combustion of liquid fuels, petrol and diesel type. Analyzing the results obtained are proposed solutions for reducing VOC emissions. The rule under which these solutions have been proposed to reduce the concentration of VOCs took into account the possibility implementation and maintenance costs thereof.

Biostimulation of soil polluted 10000 ppm of waste motor oil and phytoremediation with Cicer arietinum improved by Bacillus cereus/Rhizobium etli

Directory of Open Access Journals (Sweden)

Juárez-Cisneros Gladys

2016-08-01

Full Text Available Soil pollution by waste motor oil (WMO is reducing its productivity. An alternative for removing WMO from soil is by biostimulation (BIS applying animal manure and then phytoremediation (PR by legume improving with plant growth promoting bacteria (PGPB to reduce WMO concentration at level below 4400 ppm limit permit for the NOM-138-SEMARNAT/SSA1-2012 (NOM-138. The aims of this re-search were: i to analyze soil biostimulation polluted by 10000 ppm of WMO applying vermicompost, then subsequent soil phytoremediation with Cicer arietinum inoculated by Bacillus cereus and/or Rhizo-bium etli. In soil after applying BS by VC was measured WMO soil concentration and ii for PR was regarded phenology and biomass of C. arietinum and WMO concentration remaining at the end of this step. The results showed that soil biostimulated by VC, WMO was reduced at 1370 ppm, subsequent PR sowing C. arietinum with R. etli, WMR was reduced at 30 ppm concentration both values below to maxi-mum value accepted by NOM-138. Those data indicate that in soil polluted by WMO the best way to biorecovery soil was to integrate strategy BS/PR the last one improved by genus of PGPB.

Atmospheric pollutants monitoring by analysis of epiphytic lichens

International Nuclear Information System (INIS)

Fuga, Alessandra; Saiki, Mitiko; Marcelli, Marcelo P.; Saldiva, Paulo H.N.

2008-01-01

The Canoparmelia texana epiphytic lichenized fungi was used to monitor atmospheric pollution in the Sao Paulo metropolitan region, SP, Brazil. The cluster analysis applied to the element concentration values confirmed the site groups of different levels of pollution due to industrial and vehicular emissions. In the distribution maps of element concentrations, higher concentrations of Ba and Mn were observed in the vicinity of industries and of a petrochemical complex. The highest concentration of Co found in lichens from the Sao Miguel Paulista site is due to the emissions from a metallurgical processing plant that produces this element. For Br and Zn, the highest concentrations could be associated both to vehicular and industrial emissions. Exploratory analyses revealed that the accumulation of toxic elements in C. texana may be of use in evaluating the human risk of cardiopulmonary mortality due to prolonged exposure to ambient levels of air pollution. - Canoparmelia texana lichenized fungi is a valuable biomonitor for atmospheric pollution

Perspective of environmental pollution

Energy Technology Data Exchange (ETDEWEB)

Argent, B.B.; Thompson, D. [Sheffield Univ., Dept. of Engineering Materials, Sheffield (United Kingdom); Edyvean, R.G.J. [Sheffield Univ., Dept. of Chemical and Process Engineering, Sheffield (United Kingdom); Spears, D.A. [Sheffield Univ., Dept. of Earth Sciences, Sheffield (United Kingdom)

2004-04-01

This article aims to stimulate interest in pollution problems that are associated with the minerals industries. Because this subject is so broad, this study has concentrated on a limited number of topics that have been studied by the authors. After a brief survey indicating major sources of pollution through gaseous emissions, contamination of waterways and land fill sites, attention is focused on some of the methods of predicting, monitoring and limiting emissions together with remediation of polluted sites. (Author)

Interaction between local and regional pollution during Escompte 2001: impact on surface ozone concentrations (IOP2a and 2b)

Science.gov (United States)

Cousin, F.; Tulet, P.; Rosset, R.

2005-03-01

Escompte, a European programme which took place in the Marseille region in June-July 2001, has been designed as an exhaustive database to be used for the development and validation of air pollution models. The air quality Mesoscale NonHydrostatic Chemistry model (Meso-NH-C) is used to simulate 2 days of an Intensive Observation Period (IOP) documented during the Escompte campaign, June 23 and 24, 2001. We first study the synoptic and local meteorological situation on June 23 and 24, using surface and aircraft measurements. Then, we focus on the pollution episode of June 24. This study emphasizes the deep impact of synoptic and local dynamics on observed ozone concentrations. It is shown that ozone levels are due both to regional and local factors, with highlights of the importance of ozone layering. More generally this confirms, even in an otherwise predominant local sea-breeze regime, the need to consider larger scale regional pollutant transport.

Traffic-related air pollution increased the risk of Parkinson's disease in Taiwan: A nationwide study.

Science.gov (United States)

Lee, Pei-Chen; Liu, Li-Ling; Sun, Yu; Chen, Yu-An; Liu, Chih-Ching; Li, Chung-Yi; Yu, Hwa-Lung; Ritz, Beate

2016-11-01

Ambient air pollution has been associated with many health conditions, but little is known about its effects on neurodegenerative diseases, such as Parkinson's disease (PD). In this study, we investigated the influence of ambient air pollution on PD in a nationwide population-based case-control study in Taiwan. We identified 11,117 incident PD patients between 2007 and 2009 from the Taiwanese National Health Insurance Research Database and selected 44,468 age- and gender-matched population controls from the longitudinal health insurance database. The average ambient pollutant exposure concentrations from 1998 through the onset of PD were estimated using quantile-based Bayesian Maximum Entropy models. Basing from logistic regression models, we estimated the odds ratios (ORs) and 95% confidence intervals (CIs) of ambient pollutant exposures and PD risk. We observed positive associations between NO x , CO exposures, and PD. In multi-pollutant models, for NO x and CO above the 75th percentile exposure compared with the lowest percentile, the ORs of PD were 1.37 (95% CI=1.23-1.52) and 1.17 (95% CI=1.07-1.27), respectively. This study suggests that ambient air pollution exposure, especially from traffic-related pollutants such as NO x and CO, increases PD risk in the Taiwanese population. Copyright © 2016 Elsevier Ltd. All rights reserved.

A national-scale review of air pollutant concentrations measured in the U.S. near-road monitoring network during 2014 and 2015

Science.gov (United States)

DeWinter, Jennifer L.; Brown, Steven G.; Seagram, Annie F.; Landsberg, Karin; Eisinger, Douglas S.

2018-06-01

In 2010, the U.S. Environmental Protection Agency (EPA) revised the National Ambient Air Quality Standards (NAAQS) for NO2 to include a primary health-based standard for hourly NO2, and required air quality monitoring next to major roadways in urban areas in the U.S. Requirements for near-road measurements also include carbon monoxide (CO) and particulate matter smaller than 2.5 μm in diameter (PM2.5). We performed a national-scale assessment of air pollutants measured at 81 sites in the near-road environment during the first two years (2014 and 2015) of the new measurement program. We evaluated how concentrations at these locations compared to the NAAQS, to concentrations measured at other sites within the same urban areas, and when considering their site characteristics (distance of monitor to road, traffic volume, and meteorology). We also estimated the contribution of emissions from adjacent roadways at each near-road site to the PM2.5 concentrations above the local urban background concentrations, i.e., the near-road "increment." Hourly values of CO reached a maximum of 4.8 ppm across 31 sites in 2014 and 9.6 ppm across 47 sites in 2015, and were well below the NAAQS levels for both the 1-hr (35 ppm) and 8-hr (9 ppm) standards. Hourly concentrations of near-road NO2 reached 258 ppb across 40 sites in 2014; however, there were only two occurrences of a daily 1-hr maximum NO2 concentration above 100 ppb (the level of the hourly NO2 standard). In 2015, hourly concentrations of near-road NO2, monitored at 61 sites in 55 urban areas, reached 154 ppb. Only 0.0015% (n = 5) of hourly NO2 observations in 2015 exceeded 100 ppb. The highest annual NO2 average recorded in 2015 (29.9 ppb) occurred at the Ontario site located along I-10 in the Los Angeles, California, area and was below the level of the NO2 annual standard (53 ppb); in 2014, the highest annual mean NO2 was also observed in Los Angeles at the Anaheim site (27.1 ppb). In 2014, sites in Cincinnati

Laser-excited fluorescence for measuring atmospheric pollution

Science.gov (United States)

Menzies, R. T.

1975-01-01

System measures amount of given pollutant at specific location. Infrared laser aimed at location has wavelength that will cause molecules of pollutant to fluoresce. Detector separates fluorescence from other radiation and measures its intensity to indicate concentration of pollutant.

Fluoride pollution of atmospheric precipitation and its relationship with air circulation and weather patterns (Wielkopolski National Park, Poland).

Science.gov (United States)

Walna, Barbara; Kurzyca, Iwona; Bednorz, Ewa; Kolendowicz, Leszek

2013-07-01

A 2-year study (2010-2011) of fluorides in atmospheric precipitation in the open area and in throughfall in Wielkopolski National Park (west-central Poland) showed their high concentrations, reaching a maximum value of 2 mg/l under the tree crowns. These high values indicate substantial deposition of up to 52 mg/m(2)/year. In 2011, over 51% of open area precipitation was characterized by fluoride concentration higher than 0.10 mg/l, and in throughfall such concentrations were found in more than 86% of events. In 2010, a strong connection was evident between fluoride and acid-forming ions, and in 2011, a correlation between phosphate and nitrite ions was seen. Analysis of available data on F(-) concentrations in the air did not show an unequivocal effect on F(-) concentrations in precipitation. To find reasons for and source areas of high fluoride pollution, the cases of extreme fluoride concentration in rainwater were related to atmospheric circulation and weather patterns. Weather conditions on days of extreme pollution were determined by movement of weather fronts over western Poland, or by small cyclonic centers with meteorological fronts. Macroscale air advection over the sampling site originated in the western quadrant (NW, W, and SW), particularly in the middle layers of the troposphere (2,500-5,000 m a.s.l.). Such directions indicate western Poland and Germany as possible sources of the pollution. At the same time in the lower troposphere, air inflow was frequently from the north, showing short distance transport from local emitters, and from the agglomeration of Poznań.

Low correlation between household carbon monoxide and particulate matter concentrations from biomass-related pollution in three resource-poor settings

Energy Technology Data Exchange (ETDEWEB)

Klasen, Elizabeth M.; Wills, Beatriz [Division of Pulmonary and Critical Care, School of Medicine, Johns Hopkins University, Baltimore (United States); Naithani, Neha [Division of Pulmonary and Critical Care, School of Medicine, Johns Hopkins University, Baltimore (United States); Nepal Nutrition Intervention Project Sarlahi, Kathmandu (Nepal); Gilman, Robert H. [Program in Global Disease Epidemiology and Control, Bloomberg School of Public Health, Johns Hopkins University, Baltimore (United States); Tielsch, James M. [Department of Global Health, School of Public Health and Health Services, George Washington University, Washington DC (United States); Chiang, Marilu [Biomedical Research Unit, A.B. PRISMA, Lima (Peru); Khatry, Subarna [Nepal Nutrition Intervention Project Sarlahi, Kathmandu (Nepal); Breysse, Patrick N. [Department of Environmental Health Sciences, Bloomberg School of Public Health, Johns Hopkins University, Baltimore (United States); Menya, Diana [School of Public Health, Moi University, Eldoret (Kenya); AMPATH (Academic Model Providing Access to Healthcare), Eldoret (Kenya); Apaka, Cosmas [AMPATH (Academic Model Providing Access to Healthcare), Eldoret (Kenya); Carter, E. Jane; Sherman, Charles B. [AMPATH (Academic Model Providing Access to Healthcare), Eldoret (Kenya); Division of Pulmonary Medicine, The Warren Alpert School of Medicine, Brown University, Providence (United States); Miranda, J. Jaime [CRONICAS Center of Excellence in Chronic Diseases, Universidad Peruana Cayetano Heredia, Lima (Peru); Checkley, William, E-mail: wcheckl1@jhmi.edu [Division of Pulmonary and Critical Care, School of Medicine, Johns Hopkins University, Baltimore (United States); Program in Global Disease Epidemiology and Control, Bloomberg School of Public Health, Johns Hopkins University, Baltimore (United States); CRONICAS Center of Excellence in Chronic Diseases, Universidad Peruana Cayetano Heredia, Lima (Peru)

2015-10-15

Household air pollution from the burning of biomass fuels is recognized as the third greatest contributor to the global burden of disease. Incomplete combustion of biomass fuels releases a complex mixture of carbon monoxide (CO), particulate matter (PM) and other toxins into the household environment. Some investigators have used indoor CO concentrations as a reliable surrogate of indoor PM concentrations; however, the assumption that indoor CO concentration is a reasonable proxy of indoor PM concentration has been a subject of controversy. We sought to describe the relationship between indoor PM{sub 2.5} and CO concentrations in 128 households across three resource-poor settings in Peru, Nepal, and Kenya. We simultaneously collected minute-to-minute PM{sub 2.5} and CO concentrations within a meter of the open-fire stove for approximately 24 h using the EasyLog-USB-CO data logger (Lascar Electronics, Erie, PA) and the personal DataRAM-1000AN (Thermo Fisher Scientific Inc., Waltham, MA), respectively. We also collected information regarding household construction characteristics, and cooking practices of the primary cook. Average 24 h indoor PM{sub 2.5} and CO concentrations ranged between 615 and 1440 μg/m{sup 3}, and between 9.1 and 35.1 ppm, respectively. Minute-to-minute indoor PM{sub 2.5} concentrations were in a safe range (<25 μg/m{sup 3}) between 17% and 65% of the time, and exceeded 1000 μg/m{sup 3} between 8% and 21% of the time, whereas indoor CO concentrations were in a safe range (<7 ppm) between 46% and 79% of the time and exceeded 50 ppm between 4%, and 20% of the time. Overall correlations between indoor PM{sub 2.5} and CO concentrations were low to moderate (Spearman ρ between 0.59 and 0.83). There was also poor agreement and evidence of proportional bias between observed indoor PM{sub 2.5} concentrations vs. those estimated based on indoor CO concentrations, with greater discordance at lower concentrations. Our analysis does not support the

Low correlation between household carbon monoxide and particulate matter concentrations from biomass-related pollution in three resource-poor settings

International Nuclear Information System (INIS)

Klasen, Elizabeth M.; Wills, Beatriz; Naithani, Neha; Gilman, Robert H.; Tielsch, James M.; Chiang, Marilu; Khatry, Subarna; Breysse, Patrick N.; Menya, Diana; Apaka, Cosmas; Carter, E. Jane; Sherman, Charles B.; Miranda, J. Jaime; Checkley, William

2015-01-01

Household air pollution from the burning of biomass fuels is recognized as the third greatest contributor to the global burden of disease. Incomplete combustion of biomass fuels releases a complex mixture of carbon monoxide (CO), particulate matter (PM) and other toxins into the household environment. Some investigators have used indoor CO concentrations as a reliable surrogate of indoor PM concentrations; however, the assumption that indoor CO concentration is a reasonable proxy of indoor PM concentration has been a subject of controversy. We sought to describe the relationship between indoor PM 2.5 and CO concentrations in 128 households across three resource-poor settings in Peru, Nepal, and Kenya. We simultaneously collected minute-to-minute PM 2.5 and CO concentrations within a meter of the open-fire stove for approximately 24 h using the EasyLog-USB-CO data logger (Lascar Electronics, Erie, PA) and the personal DataRAM-1000AN (Thermo Fisher Scientific Inc., Waltham, MA), respectively. We also collected information regarding household construction characteristics, and cooking practices of the primary cook. Average 24 h indoor PM 2.5 and CO concentrations ranged between 615 and 1440 μg/m 3 , and between 9.1 and 35.1 ppm, respectively. Minute-to-minute indoor PM 2.5 concentrations were in a safe range (<25 μg/m 3 ) between 17% and 65% of the time, and exceeded 1000 μg/m 3 between 8% and 21% of the time, whereas indoor CO concentrations were in a safe range (<7 ppm) between 46% and 79% of the time and exceeded 50 ppm between 4%, and 20% of the time. Overall correlations between indoor PM 2.5 and CO concentrations were low to moderate (Spearman ρ between 0.59 and 0.83). There was also poor agreement and evidence of proportional bias between observed indoor PM 2.5 concentrations vs. those estimated based on indoor CO concentrations, with greater discordance at lower concentrations. Our analysis does not support the notion that indoor CO concentration is a

Nanoparticle-organic pollutant interaction dataset

Data.gov (United States)

U.S. Environmental Protection Agency — Dataset presents concentrations of organic pollutants, such as polyaromatic hydrocarbon compounds, in water samples. Water samples of known volume and concentration...

Effects of age, sex and reproductive status on persistent organic pollutant concentrations in 'Southern Resident' killer whales

International Nuclear Information System (INIS)

Krahn, Margaret M.; Bradley Hanson, M.; Schorr, Gregory S.; Emmons, Candice K.; Burrows, Douglas G.; Bolton, Jennie L.; Baird, Robin W.; Ylitalo, Gina M.

2009-01-01

'Southern Resident' killer whales (Orcinus orca) that comprise three fish-eating 'pods' (J, K and L) were listed as 'endangered' in the US and Canada following a 20% population decline between 1996 and 2001. Blubber biopsy samples from Southern Resident juveniles had statistically higher concentrations of certain persistent organic pollutants than were found for adults. Most Southern Resident killer whales, including the four juveniles, exceeded the health-effects threshold for total PCBs in marine mammal blubber. Maternal transfer of contaminants to the juveniles during rapid development of their biological systems may put these young whales at greater risk than adults for adverse health effects (e.g., immune and endocrine system dysfunction). Pollutant ratios and field observations established that two of the pods (K- and L-pod) travel to California to forage. Nitrogen stable isotope values, supported by field observations, indicated possible changes in the diet of L-pod over the last decade.

Measuring environmental quality. An index of pollution

International Nuclear Information System (INIS)

Khanna, N.

2000-01-01

This paper develops an index of pollution based on the epidemiological dose-response function associated with each pollutant, and the welfare losses due to exposure to pollution. The probability of damage is translated into welfare losses, which provides the common metric required for aggregation. Isopollution surfaces may then be used to compare environmental quality over time and space. An Air Pollution Index (API) is computed using 1997 data for the criteria pollutants under the Clean Air Act (CAA). The results are compared with the EPA's Pollutant Standards Index (PSI). Two significant differences emerge: unlike the PSI, the API facilitates a detailed ranking of regions by air quality and API values may contradict PSI results. Some regions with PSI values of 100-200 are considered less polluted under the proposed methodology than those with PSI values between 50 and 100. The key reason for the difference is that PSI values are determined entirely by the gas with the highest relative concentration whereas the API value is based on the ambient concentrations of all pollutants. 14 refs

Atmospheric pollution in our environment

International Nuclear Information System (INIS)

Tanvir, G.

1986-01-01

Air pollution is associated with all the activities of humans. It is becoming a serious problem in coming years so it is relevant to find out how seriously our atmosphere is being polluted and how this pollution affects human and plant life in our environment. Not only the human activities are the source of our pollution but nature causes more pollution. Air pollution that is due to the pressure of foreign substances in air, effects the quality and concentration of air substances. It is not only injurious to property, but also to vegetation and animal life. Air pollution is one of our most serious environmental problems. The sources vary from smoke-stacks and automobiles to noise and foreon containing aerosols. (orig./A.B.)

Sewage water pollutants removal efficiency correlates to the concentration gradient of amendments

International Nuclear Information System (INIS)

Bhatti, Z.A.; Mahmood, Q.; Raja, I.A.

2009-01-01

Three coagulants viz. alum, FeCl/sub 3/ and Moringa oleifera seed extract were compared for treating municipal wastewater. The wastewater samples were collected from a drain near the Murree Road in Abbottabad city. The initial treatment depicted that alum was a suitable coagulant, while the other two caused color development and increased chemical oxygen demand in the effluent. Subsequently, wastewater samples were treatment with graded concentrations (4 32 mg.L/sup -1/ of alum in batch series, and shacked at 600-620 rpm for five minutes. The treated samples were analyzed for various water quality parameters to examine the effective coagulation and flocculation process in the wastewater. There was an increase in TDS and electrical conductivity with the increasing levels of alum above the optimized values (22 to 30 mg L/sup -1/). The process primary treatment strategy of wastewater treatment with alum is suitable for reducing the pollutants load in the sewer system. (author)

Distribution of air pollutants in the Inn Valley atmosphere during high concentration events in winter 2006

International Nuclear Information System (INIS)

Schnitzhofer, R.; Norman, M; Dunkl, J.; Wistaler, A.; Hansel, A.; Neininger, B.; Gohm, A.

2006-01-01

Full text: The goal of the INNOX field campaign, which took place during January and February 2006 near the town of Schwaz, was to obtain a three-dimensional picture of the spatial distribution of air pollutants in the Inn Valley during wintertime. For this purpose continuous ground based measurements and, on six chosen days, vertical profiles within the lowest 200 m above ground level (AGL) of the valley atmosphere of certain VOCs (benzene, toluene, etc.) and CO were performed using a proton-transfer-reaction mass spectrometry instrument (PTR-MS). For the soundings a 200-m long teflon line was fixed on a tethered balloon through which the air was sucked to the PTR-MS instrument and to a CO analyser. Next to the inlet on the tethered balloon meteorological data, such as air temperature, pressure, wind, were measured as well. Above the lowest 200 m AGL a research aircraft from MetAir AG (Switzerland), equipped with various instruments for in-situ measurements of air pollutants and meteorological data, was operated. A typical flight pattern consisted of five vertical cross sections between about 150 to 2500 m AGL and lasted about three hours. Altogether 25 hours of aircraft measurements were carried out on six different days. The combination of low-level balloon measurements and upper-level aircraft observations yields vertical profiles of various parameters which cover the whole valley atmosphere. Preliminary results which show strong vertical but also horizontal gradients of air pollutant concentrations will be presented. (author)

A modified SINTACS method for groundwater vulnerability and pollution risk assessment in highly anthropized regions based on NO3- and SO42- concentrations.

Science.gov (United States)

Busico, Gianluigi; Kazakis, Nerantzis; Colombani, Nicolò; Mastrocicco, Micòl; Voudouris, Konstantinos; Tedesco, Dario

2017-12-31

Groundwater vulnerability and risk assessment are worldwide tools in supporting groundwater protection and land planning. In this study, we used three of these different methodologies applied to the Campanian Plain located in southern Italy: SINTACS, AVI and LOS. However, their capability to describe the observed chemical pollution of the area has resulted quite poor. For such a reason, a modified SINTACS method has been then implemented in the area in order to get a more reliable view of groundwater vulnerability. NO 3 - and SO 4 2- from more than 400 monitoring wells were used for specific vulnerability assessment. Land use was chosen as key parameter to infer the risk of groundwater pollution in our area. The new methodology seems to show a higher correlation with observed NO 3 - concentrations and a more reliable identification of aquifer's pollution hot spots. The main sources of NO 3 - were found in sub-urban areas, where vulnerability and risk are higher than in other areas. Otherwise due to reducing conditions triggered by the presence of elevated sedimentary organic matter and peat, concentrations below agricultural areas were lower than in sub-urban areas. The SO 4 2- specific vulnerability map showed a positive correlation with observed concentrations, due to geogenic and anthropogenic SO 4 2- sources present in the area. The combination of both NO 3 - and SO 4 2- derived risk maps becomes essential to improve the conceptual model of aquifer pollution in this severely anthropized area. The application of this new and original approach shed light on the strengths and weaknesses of each of the described previous methods and clearly showed how anthropogenic activities have to be taken into account in the assessment process. Copyright © 2017 Elsevier B.V. All rights reserved.

Air pollution episodes associated with East Asian winter monsoons

Energy Technology Data Exchange (ETDEWEB)

Hien, P.D., E-mail: pdhien@gmail.com [Vietnam Atomic Energy Agency, 59 Ly Thuong Kiet str. Hanoi (Viet Nam); Loc, P.D.; Dao, N.V. [National Hydro-Meteorological Center, 62-A2 Nguyen Chi Thanh str. Hanoi (Viet Nam)

2011-11-01

A dozen multi-day pollution episodes occur from October to February in Hanoi, Vietnam due to prolonged anticyclonic conditions established after the northeast monsoon surges (cold surges). These winter pollution episodes (WPEs) account for most of the 24-h PM{sub 10} exceedances and the highest concentrations of gaseous pollutants in Hanoi. In this study, WPEs were investigated using continuous air quality monitoring data and information on upper-air soundings and air mass trajectories. The 24-h pollutant concentrations are lowest during cold surges; concurrently rise thereafter reaching the highest levels toward the middle of a monsoon cycle, then decline ahead of the next cold surge. Each monsoon cycle usually proceeds through a dry phase and a humid phase as Asiatic continental cold air arrives in Hanoi through inland China then via the East China Sea. WPEs are associated with nighttime radiation temperature inversions (NRTIs) in the dry phase and subsidence temperature inversions (STIs) in the humid phase. In NRTI periods, the rush hour pollution peak is more pronounced in the evening than in the morning and the pollution level is about two times higher at night than in daytime. In STI periods, broad morning and evening traffic peaks are observed and pollution is as high at night as in daytime. The close association between pollution and winter monsoon meteorology found in this study for the winter 2003-04 may serve as a basis for advance warning of WPEs and for forecasting the 24-h pollutant concentrations. - Highlights: {yields} Dozen pollution episodes from Oct. to Feb in Hanoi associated with anticyclones after monsoon surges. {yields} 24-h concentrations of PM{sub 10}, SO{sub 2}, NO{sub 2}, CO rise after surge and decline ahead of the next. {yields} Episodes caused by nighttime radiation and subsidence inversions in dry and humid monsoon phases. {yields} Distinct diurnal variations of pollutant concentrations observed in the two periods. {yields} Close

Evaluation of 5 Air Criteria Pollutants; Tehran, Iran

Directory of Open Access Journals (Sweden)

Mazaheri Tehrani A. MSc,

2015-09-01

Full Text Available Aims Tehran’s uncontrolled expansion, which promoted housing, public utilities, industries and increase of vehicles caused the problem of air pollution. Necessary information about air quality in different places and different times is the first step of combating the air pollution. The purpose of this study was to investigate the annual, monthly and hourly average of 5 criteria air pollutants (PM10, O3, NO2, SO2, CO of Tehran City, Iran. Instrument & Methods The hourly concentrations of PM10, O3, NO2, SO2, CO were obtained from 21 air quality-measuring stations of Tehran City, Iran, during April 2012 to March 2013. Data were presented by descriptive statistics in the form of mean and standard deviation. Findings CO concentration was not changed during the period of study. Nitrogen dioxide increased in spring and winter. Sulfur dioxide was not changed in the first six months of the year but its concentration increased in winter. Trend of changes of floating particles showed increasing the concentration of this pollutant in May 2012 and January 2013. Ozone concentration increased in the warm seasons and decreased in the cold seasons. Conclusion PM10, O3, NO2, SO2 and CO has high concentrations and cold periods of the year are more polluted than the warm periods in Tehran City, Iran.

A cooperative reduction model for regional air pollution control in China that considers adverse health effects and pollutant reduction costs.

Science.gov (United States)

Xie, Yujing; Zhao, Laijun; Xue, Jian; Hu, Qingmi; Xu, Xiang; Wang, Hongbo

2016-12-15

How to effectively control severe regional air pollution has become a focus of global concern recently. The non-cooperative reduction model (NCRM) is still the main air pollution control pattern in China, but it is both ineffective and costly, because each province must independently fight air pollution. Thus, we proposed a cooperative reduction model (CRM), with the goal of maximizing the reduction in adverse health effects (AHEs) at the lowest cost by encouraging neighboring areas to jointly control air pollution. CRM has two parts: a model of optimal pollutant removal rates using two optimization objectives (maximizing the reduction in AHEs and minimizing pollutant reduction cost) while meeting the regional pollution control targets set by the central government, and a model that allocates the cooperation benefits (i.e., health improvement and cost reduction) among the participants according to their contributions using the Shapley value method. We applied CRM to the case of sulfur dioxide (SO 2 ) reduction in Yangtze River Delta region. Based on data from 2003 to 2013, and using mortality due to respiratory and cardiovascular diseases as the health endpoints, CRM saves 437 more lives than NCRM, amounting to 12.1% of the reduction under NCRM. CRM also reduced costs by US $65.8×10 6 compared with NCRM, which is 5.2% of the total cost of NCRM. Thus, CRM performs significantly better than NCRM. Each province obtains significant benefits from cooperation, which can motivate them to actively cooperate in the long term. A sensitivity analysis was performed to quantify the effects of parameter values on the cooperation benefits. Results shown that the CRM is not sensitive to the changes in each province's pollutant carrying capacity and the minimum pollutant removal capacity, but sensitive to the maximum pollutant reduction capacity. Moreover, higher cooperation benefits will be generated when a province's maximum pollutant reduction capacity increases. Copyright �

Comparison of indoor air pollutants concentration in two Romanian classrooms

Science.gov (United States)

Vasile, Vasilica; Dima, Alina; Zorila, Elena; Istrate, Andrei; Catalina, Tiberiu

2018-02-01

This paper investigates the air pollutions in space ventilated in two High School classrooms. The analysis consists of comparison of one classroom with hybrid ventilation system and another one stander-by classroom with natural ventilation. Several studies regarding indoor air quality during the experimental campaign have been done for VOC, CO2, CO, other pollutants, keeping monitored for humidity and temperature. The experimental demonstrated that the highest value for CO2 in stander-by classroom is 2691 ppm and in classroom with hybrid ventilation is 1897 ppm, while values for CO are 1.1 / 1.1 ppm and VOC 0.14 / 0.06 ppm, better use hybrid ventilation.

Ecological assessment of oil-gas producing area in Kazakhstan zone of Caspian sea and using the bioremediation technology for cleaning of high level oil polluted sites

International Nuclear Information System (INIS)

Bigaliev, A.A.; Ishanova, N.E.; Bijazheva, S.M.; Novikova, A.; Bigaliev, A.B.

2008-01-01

A significant part of mineral raw material resources of Kazakhstan placed in the depth of the Caspian region, where more than 90% extracting of oil and natural gas, 100% balance store rare ground, 3.2% uranium, ore 0.3%, 90.5% sawn store concentrated. Last years, it takes intensive works by extraction of carbon raw materials in Kazakhstan sector of the Caspian sea. It brought to exceeding of coastal pollution at the North and middle the Caspian coastal pollution with oil products in average till 0.282 mg/l. Maximum meaning oil product pollution reaches 0.56 mg/l (which means exceeding of limited concentration on 11 times). How much money need to cover cost of remediation in real sites? Develop of assessment and monitoring procedures based on fate mechanisms for most of representative hydrocarbons in polluted soils. Step 1 - Collection of heavily polluted portions of soils, separation of hydrocarbons by cost efficient mechanical procedures and send HC rich material (HC>95%) to prepare of alternative fuel. Return of low HC content sand to project area (HC<5.0%). Step 2 - Development of low cost bioremediation procedures in areas transformed to moderately polluted site (HC<5% after removing of heavily polluted portions) with uniform HC content. We are needed to develop of coast efficiency approach for cleaning of high level oily polluted sites around urban areas in Kazakhstan new methodology to estimate polluted area and recover of pollution history, low cost bioremediation

PM2.5 and gaseous pollutants in New York State during 2005-2016: Spatial variability, temporal trends, and economic influences

Science.gov (United States)

Squizzato, Stefania; Masiol, Mauro; Rich, David Q.; Hopke, Philip K.

2018-06-01

Over the past decades, mitigation strategies have been adopted both by federal and state agencies in the United States (US) to improve air quality. Between 2007 and 2009, the US faced a financial/economic crisis that lowered activity and reduced emissions. At the same time, changes in the prices of coal and natural gas drove a shift in fuels used for electricity generation. Seasonal patterns, diel cycles, spatial gradients, and trends in PM2.5 and gaseous pollutants concentrations (NOx, SO2, CO and O3) monitored in New York State (NYS) from 2005 to 2016 were examined. Relationships between ambient concentrations, changes in NYS emissions retrieved from the US EPA trends inventory, and economic indicators were studied. PM2.5 and primary gaseous pollutants concentrations decreased across NYS. By 2016, PM2.5 and SO2 attained relatively homogeneous concentrations across the state. PM2.5 concentrations decreased significantly at all sites. Similarly, SO2 concentrations declined at all sites within this period, with the highest slopes observed at the urban sites. Reductions in NOx emissions likely contributed to summertime average ozone reductions. NOx and VOCs controls reduced O3 peak concentrations as seen in significant relationships between the annual O3 4th-highest daily maximum 8-h concentrations and estimated NOx emissions at rural and suburban sites (r2 ∼ 0.7). Spring maxima were not reduced with most sites showing insignificant slopes or significant positive slopes (e.g., +2.6% y-1 and +2% y-1, at CCNY and PFI, respectively). Increases in autumn and winter ozone concentrations were found (e,g., 6.6 ± 0.4% y-1 on average in New York City). Significant relationships were observed between PM2.5, primary pollutants, and economic indicators. Overall, a decrease in electricity generation with coal, and the simultaneous increase in natural gas consumption for power generation, led to a decrease in PM2.5 and gaseous pollutants concentrations.

Environmental pollution and kidney diseases.

Science.gov (United States)

Xu, Xin; Nie, Sheng; Ding, Hanying; Hou, Fan Fan

2018-05-01

The burden of disease and death attributable to environmental pollution is becoming a public health challenge worldwide, especially in developing countries. The kidney is vulnerable to environmental pollutants because most environmental toxins are concentrated by the kidney during filtration. Given the high mortality and morbidity of kidney disease, environmental risk factors and their effect on kidney disease need to be identified. In this Review, we highlight epidemiological evidence for the association between kidney disease and environmental pollutants, including air pollution, heavy metal pollution and other environmental risk factors. We discuss the potential biological mechanisms that link exposure to environmental pollutants to kidney damage and emphasize the contribution of environmental pollution to kidney disease. Regulatory efforts should be made to control environmental pollution and limit individual exposure to preventable or avoidable environmental risk. Population studies with accurate quantification of environmental exposure in polluted regions, particularly in developing countries, might aid our understanding of the dose-response relationship between pollutants and kidney diseases.

Ambient and household air pollution: complex triggers of disease

Science.gov (United States)

Farmer, Stephen A.; Nelin, Timothy D.; Falvo, Michael J.

2014-01-01

Concentrations of outdoor air pollution are on the rise, particularly due to rapid urbanization worldwide. Alternatively, poor ventilation, cigarette smoke, and other toxic chemicals contribute to rising concentrations of indoor air pollution. The World Health Organization recently reported that deaths attributable to indoor and outdoor air pollutant exposure are more than double what was originally documented. Epidemiological, clinical, and animal data have demonstrated a clear connection between rising concentrations of air pollution (both indoor and outdoor) and a host of adverse health effects. During the past five years, animal, clinical, and epidemiological studies have explored the adverse health effects associated with exposure to both indoor and outdoor air pollutants throughout the various stages of life. This review provides a summary of the detrimental effects of air pollution through examination of current animal, clinical, and epidemiological studies and exposure during three different periods: maternal (in utero), early life, and adulthood. Additionally, we recommend future lines of research while suggesting conceivable strategies to curb exposure to indoor and outdoor air pollutants. PMID:24929855

Ambient and household air pollution: complex triggers of disease.

Science.gov (United States)

Farmer, Stephen A; Nelin, Timothy D; Falvo, Michael J; Wold, Loren E

2014-08-15

Concentrations of outdoor air pollution are on the rise, particularly due to rapid urbanization worldwide. Alternatively, poor ventilation, cigarette smoke, and other toxic chemicals contribute to rising concentrations of indoor air pollution. The World Health Organization recently reported that deaths attributable to indoor and outdoor air pollutant exposure are more than double what was originally documented. Epidemiological, clinical, and animal data have demonstrated a clear connection between rising concentrations of air pollution (both indoor and outdoor) and a host of adverse health effects. During the past five years, animal, clinical, and epidemiological studies have explored the adverse health effects associated with exposure to both indoor and outdoor air pollutants throughout the various stages of life. This review provides a summary of the detrimental effects of air pollution through examination of current animal, clinical, and epidemiological studies and exposure during three different periods: maternal (in utero), early life, and adulthood. Additionally, we recommend future lines of research while suggesting conceivable strategies to curb exposure to indoor and outdoor air pollutants.

Verification of the pollutant transport model 'MODIS' using EPRI plains site data from a tall stack

Energy Technology Data Exchange (ETDEWEB)

Petersen, G; Eppel, D; Grassl, H

1988-01-01

A comprehensive numerical model for the simulation of pollutant dispersion from a point source into the mixing layer of the atmosphere over flat terrain is described. A moment reduction technique is used (MODIS = Moment Distribution) to combine the simplicity of the Gaussian plume description with the versatility of Eulerian grid formulations. Turbulent dispersion coefficients are parameterized in terms of mean square wind variances which in turn are obtained by a simplified second order closure model. The data base of the 'EPRI Plume Model Validation and Development Project' is used to validate the model for wind velocities above 0.5 m/s and for horizontal scales up to about one hundred kilometers. The model describes the three-dimensional structure of a plume also for stable conditions including a nighttime low level jet. For a convective planetary boundary layer it underestimates maximum ground concentration as do other models. However, it is capable of approaching measured maximum ground concentration under stable conditions.

Atmospheric pollution over the eastern Mediterranean during summer – a review

Directory of Open Access Journals (Sweden)

U. Dayan

2017-11-01

the formation of O3 over the EM were found to be 2 to 10 times higher than in the hemispheric background troposphere. Several factors favor sulfate particulate abundance over the EM. Models, aircraft measurements, and satellite-derived data have clearly shown that sulfate has a maximum during spring and summer over the EM. The carbon monoxide (CO seasonal cycle, as obtained from global background monitoring sites in the EM, is mostly controlled by the tropospheric concentration of the hydroxyl radical (OH and therefore demonstrates high concentrations over winter months and the lowest concentrations during summer when photochemistry is active. Modeling studies have shown that the diurnal variations in CO concentration during the summer result from long-range CO transport from European anthropogenic sources, contributing 60 to 80 % of the boundary-layer CO over the EM. The values retrieved from satellite data enable us to derive the spatial distribution of methane (CH4, identifying August as the month with the highest levels over the EM. The outcomes of a recent extensive examination of the distribution of methane over the tropospheric Mediterranean Basin, as part of the Chemistry-Aerosol Mediterranean Experiment (ChArMEx program, using model simulations and satellite measurements, are coherent with other previous studies. Moreover, this methane study provides some insight into the role of the Asian monsoon anticyclone in controlling the variability of CH4 pollutant within mid-to-upper tropospheric levels above the EM in summer.

Pollutant Concentrations and Emission Rates from Scripted Natural Gas Cooking Burner Use in Nine Northern California Homes

Energy Technology Data Exchange (ETDEWEB)

Singer, Brett C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Delp, William W. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lorenzetti, David M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Maddalena, Randy L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2016-10-01

METHODS: Combustion pollutant concentrations were measured during the scripted operation of natural gas cooking burners in nine homes. In addition to a base condition of closed windows, no forced air unit (FAU) use, and no mechanical exhaust, additional experiments were conducted while operating an FAU and/or vented range hood. Test homes included a 26m2 two-room apartment, a 134m2 first floor flat, and seven detached homes of 117–226m2. There were four single-story, four two-story and one 1.5 story homes. Cooktop use entailed boiling and simmering activities, using water as a heat sink. Oven and broiler use also were simulated. Time-resolved concentrations of carbon dioxide (CO2), nitric oxide (NO), nitrogen oxides (NOX), nitrogen dioxide (NO2), particles with diameters of 6 nm or larger (PN), carbon monoxide (CO), and fine particulate matter (PM2.5) were measured in the kitchen (K) and bedroom area (BR) of each home. CO2, NO, NO2, and PN data from sequential experiments were analyzed to quantify the contribution of burner use to the highest 1h and 4h time-integrated concentrations in each room. RESULTS: Four of the nine homes had kitchen 1h NO2 exceed the national ambient air quality standard (100 ppb). Two other homes had 1h NO2 exceed 50 ppb in the kitchen, and three had 1h NO2 above 50 ppb in the bedroom, suggesting substantial exposures to anyone at home when burners are used for a single substantial event. In all homes, the highest 1h kitchen PN exceeded 2 x105 cm-3-h, and the highest 4h PN exceeded 3 x105 cm-3-hr in all homes. The lowest 1h kitchen/bedroom ratios were 1.3–2.1 for NO in the apartment and two open floor plan homes. The largest K/BR ratios of 1h NO2 were in a two-story 1990s home retrofitted for deep energy savings: ratios in this home were 3.3 to 6.6. Kitchen 1h ratios of NO, NO2 and PN to CO2 were used to calculate fuel normalized emission factors (ng J-1). Range hood use substantially reduced cooking burner pollutant concentrations both

Mitigation of severe urban haze pollution by a precision air pollution control approach.

Science.gov (United States)

Yu, Shaocai; Li, Pengfei; Wang, Liqiang; Wu, Yujie; Wang, Si; Liu, Kai; Zhu, Tong; Zhang, Yuanhang; Hu, Min; Zeng, Liming; Zhang, Xiaoye; Cao, Junji; Alapaty, Kiran; Wong, David C; Pleim, Jon; Mathur, Rohit; Rosenfeld, Daniel; Seinfeld, John H

2018-05-25

Severe and persistent haze pollution involving fine particulate matter (PM 2.5 ) concentrations reaching unprecedentedly high levels across many cities in China poses a serious threat to human health. Although mandatory temporary cessation of most urban and surrounding emission sources is an effective, but costly, short-term measure to abate air pollution, development of long-term crisis response measures remains a challenge, especially for curbing severe urban haze events on a regular basis. Here we introduce and evaluate a novel precision air pollution control approach (PAPCA) to mitigate severe urban haze events. The approach involves combining predictions of high PM 2.5 concentrations, with a hybrid trajectory-receptor model and a comprehensive 3-D atmospheric model, to pinpoint the origins of emissions leading to such events and to optimize emission controls. Results of the PAPCA application to five severe haze episodes in major urban areas in China suggest that this strategy has the potential to significantly mitigate severe urban haze by decreasing PM 2.5 peak concentrations by more than 60% from above 300 μg m -3 to below 100 μg m -3 , while requiring ~30% to 70% less emission controls as compared to complete emission reductions. The PAPCA strategy has the potential to tackle effectively severe urban haze pollution events with economic efficiency.

Studying the removal of the pollutants from wetlands

Directory of Open Access Journals (Sweden)

Nevzorov Aleksandr Leonidovich

2015-04-01

Full Text Available Wetlands, considered as the territories unfit for agriculture and building, in the recent past served as the places for the industrial and municipal waste accommodation. That’s why the problems, connected with the studies of pollution and recovery duration of bogs, are rather current nowadays. The aim of this research is studying carrying out of pollutants from the polluted marsh massif. The object of the research is the Konnick bog, where the discharge of waste water from the hydrolysis plant and dumping of ash and sawmilling waste started in the fifties. The emission of waste water from the city’s treatment facilities also took place there. The Konnick bog is situated in the Arkhangelsk region. The network of stations for the ground and surface water monitoring was organized on the territory of the bog in 2004. The monitoring showed that the ground water composition has the excess of ammonium salt, phosphates, petroleum products, lignin substances, phenols, etc. Since 2004 there is a gradual decrease in concentration of the majority of pollutant, which is connected with the end of dumping of waste and discharge of waste water from the hydrolysis. In our opinion the decrease in the polluting substances concentration in marsh waters (self-cleaning happens due to dilution of ground waters. The process of the pollutants removal from the peat was investigated with the help of a specially constructed device. The researches offered an equation, which describes the relation between the relative concentration of pollutants and the ground water flow. The analysis of the results of the peat ablution showed that in order to reduce the concentration of most pollutants the water should be filtered through the peat (at least 1 liter per 1 gram of dry peat. Using the received equation the settlement curves of pollutant concentration reduction in a bog were obtained. The curves obtained according to laboratory researches correlate rather well with the data

Teaching Air Pollution in an Authentic Context

Science.gov (United States)

Mandrikas, Achilleas; Stavrou, Dimitrios; Skordoulis, Constantine

2017-04-01

This paper describes a teaching-learning sequence (TLS) about air pollution and the findings resulting from its implementation by pre-service elementary teachers (PET) currently undergraduate students of the Department of Primary Education in the National and Kapodistrian University of Athens, Greece. The TLS focused on the relation of air pollution with wind and topography in local conditions. An authentic context was provided to the students based on daily up-to-date meteorological data via the Internet in order to estimate air pollution. The results are encouraging given that PET can correlate wind and concentration of air pollutants through reading specialized angular diagrams and weather maps, can recognize the correlation of topography in the concentration of air pollutants, and can describe temperature inversion. However, the PET demonstrated clear difficulties in ability of orientation, in wind naming, and in interpretation of symbols on weather map. Finally, the implications on teaching air pollution are discussed.

Atmospheric pollution assessment from a mountainous environment in Southern Ghana: case study of Abetifi

International Nuclear Information System (INIS)

Palm, Linda Maud Naa-Dedei

2016-07-01

the atmosphere at Abetifi was recorded with a maximum total concentration (Σ8) of 15 pg/m"3. The human exposure level to dioxin-like chemicals in the air at the study location was 0.0067 pg TEQ/kg bw per day. The atmospheric pollution source observed at Abetifi was a mixed one consisting of agricultural, vehicular and from burning of biomass. Agricultural source was basically as a result of re-volatilization from polluted sinks (a secondary pollution source). (au)

Airborne pollutant concentrations and health risks in selected Apulia region (IT) areas: preliminary results from the Jonico-Salentino project

Science.gov (United States)

Buccolieri, Riccardo; Genga, Alessandra; De Donno, Antonella; Siciliano, Tiziana; Siciliano, Maria; Serio, Francesca; Grassi, Tiziana; Rispoli, Gennaro; Cavaiola, Mattia; Lionello, Piero

2017-04-01

The Jonico-Salentino project (PJS) is a multidisciplinary study funded by Apulia Region (Det. N. 188_RU - 10/11/2015) aiming to assess health risk of people living in the cities of Lecce, Brindisi and Taranto. Citizens are exposed to emissions from industrial sources, biomass burning, vehicular, naval and air traffic, as well as from natural radioactive sources (radon). In this context, this work presents some preliminary results obtained by the Unit of University of Salento (Lecce) during an experimental campaign carried out in the study areas. The campaign is devoted to (i) sample particulate matter (PM), (ii) measure micro-meteorological variables and (iii) evaluate exposure levels of residents to main pollutants. Specifically, PM is sampled using a low volume sampler, while meteorological variables (wind speed components and direction temperature, relative humidity, precipitation and global solar radiation) are measured by advanced instrumentation such as ultrasonic anemometers which allows for the estimation of turbulence fluxes. The early effects of exposure to air pollutants is evaluated by the frequency of micronucleus (a biomarker of DNA damage) in exfoliated buccal cells collected using a soft-bristled toothbrush from oral mucosa of primary school children enrolled in the study. PM concentration data collected during the campaign are characterised from a chemical and morphological point of view; the analysis of different groups of particles allows identifying different natural and anthropogenic emission sources. This is done in conjunction to the investigation of the influence of local meteorology to elucidate the contribution of specific types of sources on final concentration levels. Finally, all data are used to assess the health risk of people living in the study areas as consequence of exposure to airborne pollutants.

Lead pollution, disease, and behaviour

Energy Technology Data Exchange (ETDEWEB)

Bryce-Smith, D; Waldron, H A

1974-01-01

Sources and health effects of atmospheric lead pollution are reviewed. Most of the Pb in gasoline is emitted in the exhaust gases as an aerosol containing particles of inorganic Pb. Some organic Pb is present, but the amount is usually less than 10% of the total. The size of these particles (0.18 to 0.90 micron) ensures maximum pulmonary penetration and absorption. The fallout of airborne particles produces very high concentrations of Pb in city dust, both inside and outside houses. Unpolluted soil contains about 15 ppM Pb, but samples of city dust contain 1000 to 6000 ppM. A daily intake of as little as 30 mg of dust containing 3% Pb produces clinical Pb poisoning in a few months. There is clear evidence to support the thesis that current levels in the environment are capable of producing behavioral abnormalities of types associated with educational disorders and delinquency, and also evidence that delinquents tend to have abnormal lead metabolism.

The influence of organic amendment and nickel pollution on tomato fruit yield and quality.

Science.gov (United States)

Palacios, G; Carbonell-Barrachina, A; Gómez, I; Mataix, J

1999-01-01

The effects of organic fertilization (sludge application) and/or different levels of Ni pollution on tomato fruit yield, quality, nutrition, and Ni accumulation were investigated. The mass loading of sewage sludge solids used in this study for the amendment of a calcareous soil with low organic matter content was 2% (w/w). A control with no sewage sludge amendment was also included (S). Nickel was added to the sludge amended soil at 0, 60, 120 and 240 mg kg-1 concentrations. Sewage sludge addition to the calcareous soil significantly increased fruit yield but did not adversely affect the quality and nutritional status of the tomato fruit. The results demonstrated that sewage sludge could be successfully used as a horticultural fertilizer. Only the highest addition rate of Ni (240 mg kg-1) to an organic amended calcareous soil had negative effects on fruit yield and quality, and caused a Ni accumulation in fruit that could be considered as a hazard for human health. Thus, no toxic problems will be encountered in tomato fruit due to Ni pollution provided the total Ni (soil Ni plus Ni incorporated with sludge amendment) concentration is kept below the maximum concentration of Ni allowed for agricultural alkaline soils in Spain (112 mg Ni kg-1).

Fighting against indoor pollution; Comment lutter contre la pollution interieure des locaux?

Energy Technology Data Exchange (ETDEWEB)

Pauli, G.; Blay, F. de; Krieger, P.; Bessot, J.C. [Hopitaux Universitaires de Strasbourg, 67 (France)

1998-06-01

Two types of indoor pollution have been identified: chemical pollution and biological pollution. The principal chemical pollutants are NO{sub 2}, VOCs (volatile organic compounds and formaldehyde), ozone and SO{sub 2}. Indoor NO{sub 2} is essentially produced by gas-heaters, stoves and fire-places, at levels that can be higher than those reached outdoors. Epidemiologic studies and NO{sub 2} provocation tests in asthmatics show that indoor NO{sub 2} is capable of triggering asthma either by direct effect or by potentiating bronchial reactivity to allergens. VOCs and formaldehyde are liberated by urea-formol foams and will only have bronchial effects at levels rarely found in domestic environment. Ozone is an outdoor pollutant essentially, and the concentrations found indoors do not exceed 50% of those measured outdoors. Concentration of SO{sub 2} can reach significant levels with the use of coal heaters, yet bronchial response will only be induced at levels rarely found indoors. The first way to fight against those pollutants is to eliminate their sources (gas, coal or kerosene heaters), and to increase ventilation. In contrast, as far as ozone is concerned, it is recommended to keep windows shot during summer pollution peaks, in order to prevent it from entering the home. Biological pollution -if we except endotoxins- is mainly represented by allergenic pollution: allergens of mites, pets, cockroaches, moulds... As far as mites are concerned, the different measures suggested should often be combined: they are methods to reduce relative humidity by increasing ventilation, physical methods consisting in eliminating textiles, vacuum cleaning, using anti-mite bed covers, and chemical methods (acaricides, tannic acid..). Palliative measures are possible. For example for cat allergen: humidification of fur, limiting secondary textile reservoirs, use of vacuum cleaners and air purifiers fitted with HEPA filters. As far as cockroaches are concerned, their eviction is

Low concentration volatile organic pollutants removal in combined adsorber-desorber-catalytic reactor system

Directory of Open Access Journals (Sweden)

Arsenijević Zorana

2008-01-01

Full Text Available The removal of volatile organic compounds (VOCs from numerous emission sources is of crucial importance due to more rigorous demands on air quality. Different technologies can be used to treat the VOCs from effluent gases: absorption, physical adsorption, open flame combustion, thermal and catalytic incineration. Their appropriateness for the specific process depends on several factors such as efficiency, energy consumption, secondary pollution, capital investments etc. The distinctive features of the catalytic combustion are high efficiency and selectivity toward be­nign products, low energy consumption and absence of secondary polluti­on. The supported noble catalysts are widely used for catalytic incineration due to their low ignition temperatures and high thermal and chemical stability. In our combined system adsorption and desorption are applied in the spouted bed with draft tube (SBDT unit. The annular zone, loaded with sorbent, was divided in adsorption and desorption section. Draft tube enabled sorbent recirculation between sections. Combustion of desorbed gases to CO2 and water vapor are realized in additive catalytic reactor. This integrated device provided low concentrations VOCs removal with reduced energy consumption. Experiments were conducted on a pilot unit of 220 m3/h nominal capacity. The sorbent was activated carbon, type K81/B - Trayal Corporation, Krusevac. A sphere shaped commercial Pt/Al2O3 catalyst with "egg-shell" macro-distribution was used for the investigation of xylene deep oxidation. Within this paper the investigations of removal of xylene vapors, a typical pollutant in production of liquid pesticides, in combined adsorber/desorber/catalytic reactor system is presented.

The role of forest in mitigating the impact of atmospheric dust pollution in a mixed landscape.

Science.gov (United States)

Santos, Artur; Pinho, Pedro; Munzi, Silvana; Botelho, Maria João; Palma-Oliveira, José Manuel; Branquinho, Cristina

2017-05-01

Atmospheric dust pollution, especially particulate matter below 2.5 μm, causes 3.3 million premature deaths per year worldwide. Although pollution sources are increasingly well known, the role of ecosystems in mitigating their impact is still poorly known. Our objective was to investigate the role of forests located in the surrounding of industrial and urban areas in reducing atmospheric dust pollution. This was tested using lichen transplants as biomonitors in a Mediterranean regional area with high levels of dry deposition. After a multivariate analysis, we have modeled the maximum pollution load expected for each site taking into consideration nearby pollutant sources. The difference between maximum expected pollution load and the observed values was explained by the deposition in nearby forests. Both the dust pollution and the ameliorating effect of forested areas were then mapped. The results showed that forest located nearby pollution sources plays an important role in reducing atmospheric dust pollution, highlighting their importance in the provision of the ecosystem service of air purification.

Relationship between rooftop and on-road concentrations of traffic-related pollutants in a busy street canyon: Ambient wind effects

International Nuclear Information System (INIS)

Kwak, Kyung-Hwan; Lee, Sang-Hyun; Seo, Jaemyeong Mango; Park, Seung-Bu; Baik, Jong-Jin

2016-01-01

Rooftop and on-road measurements of O_3, NO_2, NO_x, and CO concentrations were conducted to investigate the relationship between rooftop and on-road concentrations in a busy and shallow street canyon with an aspect ratio of ∼0.3 in Seoul, Republic of Korea, from 15 April to 1 May 2014. The median road-to-roof concentration ratios, correlation coefficients between rooftop and on-road concentrations, and temporal variations of rooftop and on-road concentrations are analyzed according to the rooftop wind directions which are two cross-canyon and two along-canyon directions. The analysis results indicate that the relationship is strong when the rooftop is situated on the downwind side rather than on the upwind side. Relative to the cross-canyon wind directions, one of the along-canyon wind directions can more enhance the relationship. A conceptual framework is proposed to explain the effect of ambient wind direction on the relationship between rooftop and on-road concentrations in a street canyon. - One of the along-canyon wind directions can enhance the relationship between rooftop and on-road concentrations of traffic-related pollutants in a busy and shallow street canyon.

Fitting Statistical Distributions Functions on Ozone Concentration Data at Coastal Areas

International Nuclear Information System (INIS)

Muhammad Yazid Nasir; Nurul Adyani Ghazali; Muhammad Izwan Zariq Mokhtar; Norhazlina Suhaimi

2016-01-01

Ozone is known as one of the pollutant that contributes to the air pollution problem. Therefore, it is important to carry out the study on ozone. The objective of this study is to find the best statistical distribution for ozone concentration. There are three distributions namely Inverse Gaussian, Weibull and Lognormal were chosen to fit one year hourly average ozone concentration data in 2010 at Port Dickson and Port Klang. Maximum likelihood estimation (MLE) method was used to estimate the parameters to develop the probability density function (PDF) graph and cumulative density function (CDF) graph. Three performance indicators (PI) that are normalized absolute error (NAE), prediction accuracy (PA), and coefficient of determination (R 2 ) were used to determine the goodness-of-fit criteria of the distribution. Result shows that Weibull distribution is the best distribution with the smallest error measure value (NAE) at Port Klang and Port Dickson is 0.08 and 0.31, respectively. The best score for highest adequacy measure (PA: 0.99) with the value of R 2 is 0.98 (Port Klang) and 0.99 (Port Dickson). These results provide useful information to local authorities for prediction purpose. (author)

Spatial and Seasonal Variations of Heavy Metal Loads in Uyo Urban Drainage Stream under PS and NPS Pollution

Directory of Open Access Journals (Sweden)

O. E. Essien

2012-12-01

Full Text Available The concentration of heavy metals (HM in the 4km urban drainage stream in Uyo was studied using grab and composite sampling of water from six stations on the stream, and analyzed by a multipurpose atomic absorption spectrophotometer. The data were statistically analyzed using SPSS version 17 software arid correlated between stations and among samples. HM contamination was evaluated with the coefficient and rate of dispersion between stations and the Normalized Scatter Coefficient (NSC. The seasonal distribution of metal pollution varied individually amongst metals at stations. The Fe and Pb concentrations exceeded the safe drinking water standard, rendering the water quality not acceptable for drinking; however, the quality was within the safe limit for crop production along the river bank. The relative.dominance of heavy metals followed a different sequence in upstream leachate effluent from all downstream stations. The NSC in dry-wet season was higher than in wet season, and was in the order: Fe>Cu>Zn>Pb, showing that large but variable concentration of Fe from PS and NPS contaminated the stream at faster rate in the wet season while Pb contaminated at nearly constant rate. However, in the dry season, Fe and Pb depleted at downstream at rates far higher than Zn as Cu was increasing. Fe and Pb could be good pollution monitor for total maximum daily load (TMDL pollution monitoring programme.

Seasonal variation of copper and zinc concentrations in the oyster Saccostrea cuccullata from the Dampier Archipelago, Western Australia: implications for pollution monitoring.

Science.gov (United States)

Talbot, V

1986-12-01

The intertidal rock oyster Saccostrea cuccullata, sampled at eight sites on eight occasions over a 1-year period, contained mean Cu and Zn concentrations ranging between 34 and 267 and 206 and 4078 mg kg-1 dry weight, respectively. In the study area, Cu and Zn emanate from sewage and boat slips (antifouling paints), while Zn probably also originates from coolant water from an electricity power generating station and iron ore exporting facilities. Highest oyster wet weight, Cu and Zn concentrations and loads occurred in January (spawning period), indicating that metal variation was not reciprocating wet weight. Lowest metal concentrations and loads occurred in October (period of onset of gametogenesis), while lowest wet weight occurred in April (post-spawning period). No significant (P less than 0.001) variation in the wet to dry weight ratio was noted temporally. However, significant, though slight, variation was noted between polluted and unpolluted oysters. Results of this study indicate that pollution control monitoring programs should consider: seasonal variation of metal concentrations; portion of the year during which standards are exceeded; oyster size and availability for human consumption; suitability of standards where shellfish are not consumed as a staple diet; appropriate size indicies which can be used for selecting specimens for intersite comparisons; wet to dry weight calculations: techniques, spatial and temporal variations; and the physical dynamics of sites used.

Concentrations of Metals, Metalloids, and Chlorinated Pollutants in Blood and Plasma of White Stork (Ciconia ciconia) Nestlings From Spain.

Science.gov (United States)

Pérez-López, M; De la Casa-Resino, I; Hernández-Moreno, D; Galeano, J; Míguez-Santiyán, M P; de Castro-Lorenzo, A; Otero-Filgueiras, M; Rivas-López, O; Soler, F

2016-10-01

The aim of this study was to determine the levels of different inorganic elements (lead [Pb], mercury [Hg], and arsenic [As]) and persistent chlorinated pollutants (including polychlorinated biphenyls [PCBs] and organochlorine pesticides [OCPs]) in blood and plasma of White stork (Ciconia ciconia) nestlings from northwest (NW) Spain. The concentrations of PCBs were lower than the limit of detection in all samples. The OCPs γ-HCH, 4,4'-DDE, HCB, and endosulfan were detected most frequently in plasma from White stork nestlings. These OCPs were detected in 98, 54, 39, and 37 % of all samples, respectively. However, the concentrations of organic pollutants were lower than the risk thresholds for birds. The mean levels of the inorganic elements Pb, Hg, and As were found to be 36.92 ± 33.48, 16.48 ± 12.87, and 9.813 ± 13.84 µg/L, respectively. These levels were also lower than the risk thresholds for birds. This study not only provides a snapshot of the levels of both inorganic and organic contaminants in wild White storks in NW Spain, it also provides a useful baseline for biomonitoring levels of the measured contaminants in this area.

Air pollution and its control in China

Institute of Scientific and Technical Information of China (English)

HAO Jiming; HE Kebin; DUAN Lei; LI Junhua; WANG Litao

2007-01-01

The rapid growth of China's economy has led to severe air pollution characterized by acid rain,severe pollution in cities,and regional air pollution.High concentrations are found for various pollutants such as sulfur dioxides(SO2),nitrogen oxides(NOx),and fine particulates.Great efforts have thus been undertaken for the control of air pollution in the country.This paper discusses the development and application of appropriate technologies for reducing the major pollutants produced by coal and vehicles,and investi gates air quality modeling as an important support for policy-making.

Air pollution assessment based on elemental concentration of leaves tissue and foliage dust along an urbanization gradient in Vienna.

Science.gov (United States)

Simon, Edina; Braun, Mihály; Vidic, Andreas; Bogyó, Dávid; Fábián, István; Tóthmérész, Béla

2011-05-01

Foliage dust contains heavy metal that may have harmful effects on human health. The elemental contents of tree leaves and foliage dust are especially useful to assess air environmental pollution. We studied the elemental concentrations in foliage dust and leaves of Acer pseudoplatanus along an urbanization gradient in Vienna, Austria. Samples were collected from urban, suburban and rural areas. We analysed 19 elements in both kind of samples: aluminium, barium, calcium, copper, iron, potassium, magnesium, sodium, phosphor, sulphur, strontium and zinc. We found that the elemental concentrations of foliage dust were significantly higher in the urban area than in the rural area for aluminium, barium, iron, lead, phosphor and selenium. Elemental concentrations of leaves were significantly higher in urban than in rural area for manganese and strontium. Urbanization changed significantly the elemental concentrations of foliage dust and leaves and the applied method can be useful for monitoring the environmental load. Copyright © 2011 Elsevier Ltd. All rights reserved.

Impact of shallowly deposited ore-bearing dolomites on local soil pollution aureoles of As, Cd, Pb, and Zn in an old mining area

Energy Technology Data Exchange (ETDEWEB)

Fabijanczyk, Piotr; Zawadzki, Jaroslaw [Warsaw Univ. of Technology (Poland). Environmental Engineering Faculty

2012-10-15

The study area, located in Upper Silesian Industrial Region, was rich in significant amounts of ores that were classified of Mississippi Valley type. Being these ores especially rich in Pb and Zn, an intense development of mining and ore extraction industry was verified in this area. The goal of this study was to investigate how local pollution aureoles of As, Cd, Pb, and Zn were influenced by the presence of shallowly deposited ore-bearing dolomites. Very extensive sampling campaign was carried out, and over 1,000 samples were collected in the area of about 150 km{sup 2}. Local aureoles of investigated metals were calculated for two soil layers. The first one covered the part of soil core from the soil surface to the depth of 20 cm and the second one from the depth of 40 cm to the depth of 60 cm. All spatial distributions of particular metals in soil were calculated by means of ordinary kriging using free softwares QGIS and SAGA. Maximum concentrations of Pb and Zn in soil in study area were very high, reaching over 24,000 and 77,000 mg/kg, respectively. Maximum concentrations of As and Cd were also very high, reaching about 1,000 mg/kg. Those maximum values were observed in the direct vicinity of the Boles?aw mine and its mine dumps. Almost all local aureoles were located within the range of ore-bearing dolomites. It was especially visible for Pb and Zn, minerals very common in ore deposits. Otherwise, local aureoles of As and Cd were more related with the vicinity of mines and other pollution sources, being more associated to the anthropogenic pollution than to the presence of ore-bearing dolomites. The aureoles of Pb and Zn, and in moderate degree of As, were associated with a mineral composition of ores. Differently, the location, the shape, and spatial pattern of Cd aureoles suggest that they were mostly influenced by anthropogenic pollution. Anthropogenic factors were dominating over the lithogenic ones and masking the influence of the shallowly deposited

Total and Available Heavy Metal Concentrations and Assessment of Soil Pollution Indices in Selected Soils of Zanjan

Directory of Open Access Journals (Sweden)

M. Taheri

2017-01-01

Full Text Available Introduction: Soil is a hardly renewable natural resource. Although soil degradation, caused by either human activities and natural processes is a relatively slow procedure, but its effects are long lasting and most often, irreversible in the time scale of man's life. Among the most significant soil contaminants resulting from both natural and human sources, heavy metals are more important due to their long- term toxicity effects. For evaluating soil's enrichment rate by heavy metals, a wide and full study of soils background values, including total and available fractions of heavy metal contents should be done. Zanjan province has some great mines and concentrating industries of lead and zinc especially in Angoran, Mahneshan. Unfortunately produced waste materials of these industries spread over the adjacent areas. Investigations showed that accumulation of some heavy metals in vegetables and crops planted in this region had occurred. Therefore, performing some investigations in these polluted areas and assessing pollution rate and heavy metals distribution in arable lands had prime importance. Our goals were: 1 determining the total and available amounts of Cu, Pb, Zn and Cd in the soils of arable lands in polluted areas of Zanjan city, 2 producing the distribution map for the metals mentioned above and 3 calculating pollution indices in the soils. Materials and Methods: The study area was in south west of Zanjan city. For soil sampling, a 1 Km by 1 Km grid defined in ArcGIS software on landuse layer and totally 144 points that placed on agricultural lands, due to our goals, were sampled. For sampling, in a 5m radius around the point we collected some subsamples from depth of 0 - 15 cm, and after mixing the subsamples, finally a 1Kg soil sample prepared and sent to the laboratory. Sampled soils were air dried and were passed through a 2mm sieve. Soils organic matter (OM content and texture were determined by Walkely-Black and Bouyoucos

Atmospheric pollution and plant growth

Energy Technology Data Exchange (ETDEWEB)

Bleasdale, J K.A.

1952-03-01

Although sulfur dioxide is the most common and usually the most abundant polluting agent, experiments with this gas have shown that, under the conditions employed, there is no effect on yield unless the concentration is high enough to cause leaf injury. S23 ryegrass was grown in beds in greenhouses. Treatment with purified air gave, with one exception, a dry weight considerably higher than treatment with polluted air. No sign of leaf damage could be detected in the greenhouse with polluted air. This fact would seem to indicate that pollution decreases the growth rate, even in the absence of visible injury.

Analysis of local scale tree-atmosphere interaction on pollutant concentration in idealized street canyons and application to a real urban junction

Science.gov (United States)

Buccolieri, Riccardo; Salim, Salim Mohamed; Leo, Laura Sandra; Di Sabatino, Silvana; Chan, Andrew; Ielpo, Pierina; de Gennaro, Gianluigi; Gromke, Christof

2011-03-01

This paper first discusses the aerodynamic effects of trees on local scale flow and pollutant concentration in idealized street canyon configurations by means of laboratory experiments and Computational Fluid Dynamics (CFD). These analyses are then used as a reference modelling study for the extension a the neighbourhood scale by investigating a real urban junction of a medium size city in southern Italy. A comparison with previous investigations shows that street-level concentrations crucially depend on the wind direction and street canyon aspect ratio W/H (with W and H the width and the height of buildings, respectively) rather than on tree crown porosity and stand density. It is usually assumed in the literature that larger concentrations are associated with perpendicular approaching wind. In this study, we demonstrate that while for tree-free street canyons under inclined wind directions the larger the aspect ratio the lower the street-level concentration, in presence of trees the expected reduction of street-level concentration with aspect ratio is less pronounced. Observations made for the idealized street canyons are re-interpreted in real case scenario focusing on the neighbourhood scale in proximity of a complex urban junction formed by street canyons of similar aspect ratios as those investigated in the laboratory. The aim is to show the combined influence of building morphology and vegetation on flow and dispersion and to assess the effect of vegetation on local concentration levels. To this aim, CFD simulations for two typical winter/spring days show that trees contribute to alter the local flow and act to trap pollutants. This preliminary study indicates that failing to account for the presence of vegetation, as typically practiced in most operational dispersion models, would result in non-negligible errors in the predictions.

Mass concentration coupled with mass loading rate for evaluating PM_2_._5 pollution status in the atmosphere: A case study based on dairy barns

International Nuclear Information System (INIS)

Joo, HungSoo; Park, Kihong; Lee, Kwangyul; Ndegwa, Pius M.

2015-01-01

This study investigated particulate matter (PM) loading rates and concentrations in ambient air from naturally ventilated dairy barns and also the influences of pertinent meteorological factors, traffic, and animal activities on mass loading rates and mass concentrations. Generally, relationships between PM_2_._5 concentration and these parameters were significantly poorer than those between the PM loading rate and the same parameters. Although ambient air PM_2_._5 loading rates correlated well with PM_2_._5 emission rates, ambient air PM_2_._5 concentrations correlated poorly with PM_2_._5 concentrations in the barns. A comprehensive assessment of PM_2_._5 pollution in ambient air, therefore, requires both mass concentrations and mass loading rates. Emissions of PM_2_._5 correlated strongly and positively with wind speed, temperature, and solar radiation (R"2 = 0.84 to 0.99) and strongly but negatively with relative humidity (R"2 = 0.93). Animal activity exhibited only moderate effect on PM_2_._5 emissions, while traffic activity did not significantly affect PM_2_._5 emissions. - Highlights: • Sink PM_2_._5 loading rates correlate well with source PM_2_._5 emission rates. • Sink PM_2_._5 concentrations correlate poorly with source PM_2_._5 concentrations. • Mass loading rate complements mass concentration in appraising sink PM_2_._5 status. • PM_2_._5 emissions is dependent on wind speed, temp, solar strength, and RH. • Cow traffic activity affects PM_2_._5 emissions, while traffic activity does not. - Both PM mass loading rate and concentrations are required for comprehensive assessment of pollution potential of PM released into the atmosphere.

Characterization of effluent from food processing industries and stillage treatment trial with Eichhornia crassipes (Mart. and Panicum maximum (Jacq.

Directory of Open Access Journals (Sweden)

N.A. Noukeu

2016-12-01

Full Text Available In this study, effluents from 11 food processing industries from various sectors were characterized through analysis of physical and chemical parameters. In general, effluents pHs are between 4.07 and 7.63. Lead (Pb2+ and cadmium (Cd+ concentrations range from 0.083 to 1.025 mg/l and 0.052–0.158 mg/l respectively. The biodegradability of the effluent is very low. The principal component analysis (PCA grouped industries according to their organic matter levels; thus, stillage, livestock, molasses and sugar refinery effluents show some similarities, as well as confectionery, oil mill, dairy and brewery effluents. Forms of nitrogen measured show low levels of nitrites (NO2−, high levels of nitrates (NO3−, ammonium (NH4+ and Kjeldahl nitrogen (TKN. Among these effluents, a treatment trial with Eichhornia crassipes and Panicum maximum was applied to stillage effluent from Fermencam distillery. The results show that Panicum maximum and Eichhornia crassipes reduce pollutant loads of Fermencam's wastewater.

Synthesis report: program ecosystems, transport, pollutions, 1998 - 2001

International Nuclear Information System (INIS)

Etchelecou, A.; Deletraz, G.; Elichegaray, Ch.

2001-04-01

The ''Ecosystems, Transports, Pollution Program'' ETP Program, has been elaborated to evaluate the road pollution impacts on the mountain ecosystems. Four mountains valleys have been chosen: two in Alps (Chamonix and Maurienne) and two in Pyrenees (Biriatou and Vallee d'Aspe). This Program presents six objectives: the road traffic characterization, the pollutants emission estimation, the pollutants concentrations in the air, the pollutants dispersion according to relief, the relationships between pollutants emissions and bio-monitoring, the road pollution effects on nearby ecosystems. (A.L.B.)

Heavy metal and antibiotic resistance of Acinetobacter spp. isolated from diesel fuel polluted

Directory of Open Access Journals (Sweden)

Kais Kassim Ghaima

2018-04-01

Full Text Available Heavy metals pollution of soil and wastewater is a global problem that threatens the environment as they are not degraded or removed and the potential threat to human health comes from the multiple resistances to heavy metals and antibiotics among bacterial populations. The present study was aimed to isolate and identify multiple metal/antibiotic resistant Acinetobacter spp. from diesel fuel polluted soil of Al-Dora, Baghdad, Iraq. Initially, a total of 24 bacterial cultures (coded KNZ–1 to KNZ–24 were isolated and identified up to genus level as Acinetobacter by morphological, physiological and biochemical characteristics. Screening of heavy metals resistant Acinetobacter were conducted by streaking the isolates on nutrient agar plates supplemented with different concentrations: 10, 25, 50 and 100mg/L of the three heavy metals; Hg2+, Cd2+ and Pb2+. Out of 24 isolates, 6 (25% isolates (KNZ–3, KNZ–5, KNZ–8, KNZ–12, KNZ–16 and KNZ–21 were selected as a multiple heavy metal resistant (MHMR Acinetobacter with maximum tolerable concentrations (MTCs; 100–200mg/L for Hg2+, 300-600mg/L for Cd2+ and 100–300mg/L for Pb2+. Antibiotic resistance pattern of the selected MHMR isolates was determined by Kirby-Bauer disc diffusion method against 12 different antibiotics belonging to 7 classes. Out of 6 isolates, 4 isolates were multidrug resistance (MDR with varying degrees. Among them isolate, KNZ–16 showed a wide range of resistance to all tested antibiotics except Levofloxacin and Imipenem. It was concluded that dual resistant Acinetobacter is useful in the bioremediation of environments polluted with heavy metals especially the biodegradation of organic pollutants.

Environmental pollution by petroleum

Energy Technology Data Exchange (ETDEWEB)

Murata, T

1974-06-01

Pollution causes, cases, and remedies at various stages of petroleum production and usage are reviewed. Petroleum extraction (off-shore drilling and Arctic drilling) can be accompanied by mishaps. In 1971, IMCO (an international safety committee) proposed the partitioning of oil tanker holds into smaller compartments to minimize spillage in case of disaster. Although the solubility of oil in waste water from refineries is reckoned by ppM, the total amount dissolved is not negligible. Petroleum storage and transport on land is complicated by problems of safety in terms of population density as well as by pollution problems. Petroleum end-products such as plastic trash and automobile exhausts contribute to pollution. The role of aldehydes and peroxides in photochemical smog formation must be investigated further. Proper treatment of pollution at each specific point of occurrence, rather than at the end of a production line is recommended. Pollutant concentration for treatment, rather than pollutant dilution for dispersal, should be considered. Technology for pollution abatement is available, but not always economically feasible.

ANALYSIS OF THE RESULTS OF MEASUREMENT OF CONCENTRATIONS OF AIR POLLUTION WITH PM10 AND PM2.5 MEASURING STATION SQUARE OF POZNAN IN BYDGOSZCZ

Directory of Open Access Journals (Sweden)

Rafał Pasela

2017-02-01

Full Text Available The phenomenon of suspended particulate pollution PM10 and PM2.5 occurs in large urban areas where the main source of their presence is communication, which is primarily related to the combustion of liquid fuels. PM2.5 dust pollution is a major risk factor for diseases of the respiratory, cardiovascular, and allergy. Act regulating the standards and target dates for reducing concentrations of particulate matter in urban areas and in all the cities of over 100 thousand. residents of the Directive of the European Parliament and Council Directive 2008/50/EC of 21 May 2008. on ambient air quality and cleaner air for Europe (CAFE. The acceptable level of average daily concentration of PM10 is 50 μg/m3 and may be exceeded by not more than 35 times a year, while the level of allowable annual average concentration of 40 μg/m3. The aim of this study was to assess the state of air pollution of dust PM10 and PM2.5 for the selected area of the city of Bydgoszcz. The analysis was conducted using data from air monitoring stations located at Poznanska street. The station is owned by the Provincial Inspectorate for Environmental Protection (VIEP in Bydgoszcz. The studies have shown that the annual average concentration of particulate matter analyzed station in Bydgoszcz in the years 2013-2015 amounted to PM10 41 μg/m3 PM2.5 and 23 μg/m3. The results are on the borderline of acceptable levels of concentration resulting from the Regulation of the Minister of the Environment of 2 August 2012. The concentrations of particulate matter in ambient air are strongly associated with meteorological conditions. The definitely higher concentrations observed in the autumn-winter season. The decrease in temperature causes the combustion in the boiler house of fuels with a high emissions. The highest average daily concentration of suspended particulate matter was observed on Thursday and Friday in the winter months, and while the lowest concentration was recorded in the

Local emission of primary air pollutants and its contribution to wet deposition and concentrations of aerosols and gases in ambient air in Japan

Science.gov (United States)

Aikawa, Masahide; Hiraki, Takatoshi; Tomoyose, Nobutaka; Ohizumi, Tsuyoshi; Noguchi, Izumi; Murano, Kentaro; Mukai, Hitoshi

2013-11-01

We studied wet deposition by precipitation and the concentrations of aerosols and gases in ambient air in relation to the primary air pollutants discharged from domestic areas. The concentrations of aerosols and gases were influenced by nearby emissions except for non-sea-salt SO, which is transported long distances. The area facing the Sea of Japan showed much larger wet deposition than other areas, although the domestic emissions of the primary air pollutants there were small and showed a peak in wet deposition from October to March, as distinct from April to September in other areas. We performed the correlation analyses between wet deposition of each component and the product of the concentrations of corresponding aerosols and gases in ambient air and the two-thirds power of the precipitation. From the results, following scavenging processes were suggested. • Sulfate and ammonium were scavenged in precipitation as particulate matter such as (NH4)2SO4 and NH4HSO4. • Nitrate was scavenged mainly in precipitation through gaseous HNO3. • Ammonium was complementarily scavenged in precipitation through aerosols such as (NH4)2SO4 and NH4HSO4 and through gaseous NH3.

Investigation of air pollution of Shanghai subway stations in ventilation seasons in terms of PM2.5 and PM10.

Science.gov (United States)

Guo, Erbao; Shen, Henggen; He, Lei; Zhang, Jiawen

2017-07-01

In November 2015, the PM 2.5 and PM 10 particulate matter (PM) levels in platforms, station halls, and rail areas of the Shangcheng and Jiashan Road Station were monitored to investigate air pollution in the Shanghai subway system. The results revealed that in subway stations, PM 2.5 and PM 10 concentrations were significantly higher than those in outdoor environments. In addition, particle concentrations in the platforms exceeded maximum levels that domestic safety standards allowed. Particularly on clear days, PM 2.5 and PM 10 concentrations in platforms were significantly higher than maximum standards levels. Owing to the piston effect, consistent time-varying trends were exhibited by PM 2.5 concentrations in platforms, station halls, and rail areas. Platform particle concentrations were higher than the amount in station halls, and they were higher on clear days than on rainy days. The time-varying trends of PM 10 and PM 2.5 concentrations in platforms and station halls were similar to each other. Activities within the station led to most of the inhalable particles within the station area. The mass concentration ratios of PM 2.5 and PM 10 in platforms were within 0.65-0.93, and fine particles were the dominant components.

Use of GLM approach to assess the responses of tropical trees to urban air pollution in relation to leaf functional traits and tree characteristics.

Science.gov (United States)

Mukherjee, Arideep; Agrawal, Madhoolika

2018-05-15

Responses of urban vegetation to air pollution stress in relation to their tolerance and sensitivity have been extensively studied, however, studies related to air pollution responses based on different leaf functional traits and tree characteristics are limited. In this paper, we have tried to assess combined and individual effects of major air pollutants PM 10 (particulate matter ≤ 10 µm), TSP (total suspended particulate matter), SO 2 (sulphur dioxide), NO 2 (nitrogen dioxide) and O 3 (ozone) on thirteen tropical tree species in relation to fifteen leaf functional traits and different tree characteristics. Stepwise linear regression a general linear modelling approach was used to quantify the pollution response of trees against air pollutants. The study was performed for six successive seasons for two years in three distinct urban areas (traffic, industrial and residential) of Varanasi city in India. At all the study sites, concentrations of air pollutants, specifically PM (particulate matter) and NO 2 were above the specified standards. Distinct variations were recorded in all the fifteen leaf functional traits with pollution load. Caesalpinia sappan was identified as most tolerant species followed by Psidium guajava, Dalbergia sissoo and Albizia lebbeck. Stepwise regression analysis identified maximum response of Eucalyptus citriodora and P. guajava to air pollutants explaining overall 59% and 58% variability's in leaf functional traits, respectively. Among leaf functional traits, maximum effect of air pollutants was observed on non-enzymatic antioxidants followed by photosynthetic pigments and leaf water status. Among the pollutants, PM was identified as the major stress factor followed by O 3 explaining 47% and 33% variability's in leaf functional traits. Tolerance and pollution response were regulated by different tree characteristics such as height, canopy size, leaf from, texture and nature of tree. Outcomes of this study will help in urban forest

Pollution control in pulp and paper industrial effluents using integrated chemical-biological treatment sequences.

Science.gov (United States)

El-Bestawy, Ebtesam; El-Sokkary, Ibrahim; Hussein, Hany; Keela, Alaa Farouk Abu

2008-11-01

The main objective of the present study was to improve the quality of pulp and paper industrial wastewater of two local mills RAKTA and El-Ahlia, Alexandria, Egypt, and to bring their pollutant contents to safe discharge levels. Quality improvement was carried out using integrated chemical and biological treatment approaches after their optimization. Chemical treatment (alum, lime, and ferric chloride) was followed by oxidation using hydrogen peroxide and finally biological treatment using activated sludge (90 min for RAKTA and 60 min for El-Ahlia effluents). Chemical coagulation produced low-quality effluents, while pH adjustment during coagulation treatment did not enhance the quality of the effluents. Maximum removal of the tested pollutants was achieved using the integrated treatment and the pollutants recorded residual concentrations (RCs) of 34.67, 17.33, 0.13, and 0.43 mg/l and 15.0, 11.0, 0.0, and 0.13 mg/l for chemical oxygen demand (COD), biochemical oxygen demand (BOD5), tannin and lignin, and silica in RAKTA and El-Ahlia effluents, respectively, all of which were below their maximum permissible limits (MPLs) for the safe discharge into water courses. Specific oxygen uptake rate (SOUR) and sludge volume index (SVI) values reflect good conditions and healthy activated sludge. Based on the previous results, optimized conditions were applied as bench scale on the raw effluents of RAKTA and El-Ahlia via the batch chemical and the biological treatment sequences proposed. For RAKTA effluents, the sequence was as follows: (1) coagulation with 375 mg/l FeCl3, (2) oxidation with 50 mg/l hydrogen peroxide, and (3) biological treatment using activated sludge with 2,000 mg/l initial concentration and 90 min hydraulic retention time (HRT), while for El-Ahlia raw effluents, the sequence was (1) coagulation with 250 mg/l FeCl3, (2) oxidation with 45 mg/l hydrogen peroxide, and (3) biological treatment using activated sludge with 2,000 mg/l initial concentration and 60

Lidar: air pollution applications

International Nuclear Information System (INIS)

Collis, R.T.H.

1977-01-01

This introduction to the use of lidar in air pollution applications is mainly concerned with its capability to detect and monitor atmospheric particulates by elastic backscattering. Even when quite imperceptible to the eye, such particulates may be detected at ranges of several kilometers even by lidars of modest performance. This capability is valuable in connection with air pollution in the following ways: by mapping and tracking inhomogeneities in particulate concentration, atmospheric structure and motion may be monitored; measurements of the optical properties of the atmosphere provide an indication of turbidity or of particulate number or mass concentrations; and the capability of obtaining at a single point return signals from remote atmospheric volumes makes it possible to make range-resolved measurements of gaseous concentration along the path by using the resonant absorption of energy of appropriate wavelengths

Maximum permissible concentration of radon {sup 222}Rn in air; La concentration maximale admissible du radon 222 dans l'air

Energy Technology Data Exchange (ETDEWEB)

Hamard, J; Beau, P G; Ergas, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires, departement de la protection sanitaire, service d' hygiene atomique