Maximum permissible continuous release rates of phosphorus-32 and sulphur-35 to atmosphere in a milk producing area

Energy Technology Data Exchange (ETDEWEB)

Bryant, P M

1963-01-01

A method is given for calculating, for design purposes, the maximum permissible continuous release rates of phosphorus-32 and sulphur-35 to atmosphere with respect to milk contamination. In the absence of authoritative advice from the Medical Research Council, provisional working levels for the concentration of phosphorus-32 and sulphur-35 in milk are derived, and details are given of the agricultural assumptions involved in the calculation of the relationship between the amount of the nuclide deposited on grassland and that to be found in milk. The agricultural and meteorological conditions assumed are applicable as an annual average to England and Wales. The results (in mc/day) for phosphorus-32 and sulphur-35 for a number of stack heights and distances are shown graphically; typical values, quoted in a table, include 20 mc/day of phosphorus-32 and 30 mc/day of sulfur-35 as the maximum permissible continuous release rates with respect to ground level releases at a distance of 200 metres from pastureland.

Hazards and maximum permissible doses of radiation for man

International Nuclear Information System (INIS)

Walinder, G.

1977-11-01

Maximum permissible dose levels are primarely based on risks for genetic damage and cancer. The reason for this is the observation that such late effects of radiation seem to arise even after doses that are to low to give rise to acute effects. In contrast to the tumour incidence found in irradiated human populations no genetic effects of radiation have been observed in man. This does not mean that genetic effects have not been induced but that it has been impossible to find an increase or to discern them among all the congenital defects, that can not be ascribed to the irradiation. As a consequence, the radiological risk estimation has been concentrated on the hazard of malignant diseases. Tumour risks are generally expressed as excess rates of incidence and mortality per million persons per rem. These figures are, however, not obtained from direct epidemiological observations but have been calculated from such data under the assumption of a linear relationship between effect and radiation dose. This formal extrapolation of observed data involves an uncertainty which, of course, is proportionately greater for the calculated effects in the millirem range. However, although the calculated tumour risks can not be said to be founded on direct scientific evidence, there are scientific reasons to believe that the figures derived from the formal extrapolations constitute an upper limit of possible ri02050

Maximum permissible body burdens and maximum permissible concentrations of radionuclides in air and in water for occupational exposure. Recommendations of the National Committee on Radiation Protection. Handbook 69

Energy Technology Data Exchange (ETDEWEB)

NONE

1959-06-05

The present Handbook and its predecessors stem from the Second International Congress of Radiology, held in Stockholm in 1928. At that time, under the auspices of the Congress, the International Commission on Radiological Protection (ICRP) was organized to deal initially with problems of X-ray protection and later with radioactivity protection. At that time 'permissible' doses of X-rays were estimated primarily in terms of exposures which produced erythema, the amount of exposure which would produce a defined reddening of the skin. Obviously a critical problem in establishing criteria for radiation protection was one of developing useful standards and techniques of physical measurement. For this reason two of the organizations in this country with a major concern for X-ray protection, the American Roentgen Ray Society and the Radiology Society of North America, suggested that the National Bureau of Standards assume responsibility for organizing representative experts to deal with the problem. Accordingly, early in 1929, an Advisory Committee on X-ray and Radium Protection was organized to develop recommendations on the protection problem within the United States and to formulate United States points of view for presentation to the International Commission on Radiological Protection. The organization of the U.S. Advisory Committee included experts from both the medical and physical science fields. The recommendations of this Handbook take into consideration the NCRP statement entitled 'Maximum Permissible Radiation Exposures to Man', published as an addendum to Handbook 59 on April 15, 1958. As noted above this study was carried out jointly by the ICRP and the NCRP, and the complete report is more extensive than the material contained in this Handbook.

Maximum permissible body burdens and maximum permissible concentrations of radionuclides in air and in water for occupational exposure. Recommendations of the National Committee on Radiation Protection. Handbook 69

International Nuclear Information System (INIS)

1959-01-01

The present Handbook and its predecessors stem from the Second International Congress of Radiology, held in Stockholm in 1928. At that time, under the auspices of the Congress, the International Commission on Radiological Protection (ICRP) was organized to deal initially with problems of X-ray protection and later with radioactivity protection. At that time 'permissible' doses of X-rays were estimated primarily in terms of exposures which produced erythema, the amount of exposure which would produce a defined reddening of the skin. Obviously a critical problem in establishing criteria for radiation protection was one of developing useful standards and techniques of physical measurement. For this reason two of the organizations in this country with a major concern for X-ray protection, the American Roentgen Ray Society and the Radiology Society of North America, suggested that the National Bureau of Standards assume responsibility for organizing representative experts to deal with the problem. Accordingly, early in 1929, an Advisory Committee on X-ray and Radium Protection was organized to develop recommendations on the protection problem within the United States and to formulate United States points of view for presentation to the International Commission on Radiological Protection. The organization of the U.S. Advisory Committee included experts from both the medical and physical science fields. The recommendations of this Handbook take into consideration the NCRP statement entitled 'Maximum Permissible Radiation Exposures to Man', published as an addendum to Handbook 59 on April 15, 1958. As noted above this study was carried out jointly by the ICRP and the NCRP, and the complete report is more extensive than the material contained in this Handbook

49 CFR 192.621 - Maximum allowable operating pressure: High-pressure distribution systems.

Science.gov (United States)

2010-10-01

... STANDARDS Operations § 192.621 Maximum allowable operating pressure: High-pressure distribution systems. (a) No person may operate a segment of a high pressure distribution system at a pressure that exceeds the... segment of a distribution system otherwise designed to operate at over 60 p.s.i. (414 kPa) gage, unless...

Standard values of maximum tongue pressure taken using newly developed disposable tongue pressure measurement device.

Science.gov (United States)

Utanohara, Yuri; Hayashi, Ryo; Yoshikawa, Mineka; Yoshida, Mitsuyoshi; Tsuga, Kazuhiro; Akagawa, Yasumasa

2008-09-01

It is clinically important to evaluate tongue function in terms of rehabilitation of swallowing and eating ability. We have developed a disposable tongue pressure measurement device designed for clinical use. In this study we used this device to determine standard values of maximum tongue pressure in adult Japanese. Eight hundred fifty-three subjects (408 male, 445 female; 20-79 years) were selected for this study. All participants had no history of dysphagia and maintained occlusal contact in the premolar and molar regions with their own teeth. A balloon-type disposable oral probe was used to measure tongue pressure by asking subjects to compress it onto the palate for 7 s with maximum voluntary effort. Values were recorded three times for each subject, and the mean values were defined as maximum tongue pressure. Although maximum tongue pressure was higher for males than for females in the 20-49-year age groups, there was no significant difference between males and females in the 50-79-year age groups. The maximum tongue pressure of the seventies age group was significantly lower than that of the twenties to fifties age groups. It may be concluded that maximum tongue pressures were reduced with primary aging. Males may become weaker with age at a faster rate than females; however, further decreases in strength were in parallel for male and female subjects.

Secondary poisoning of cadmium, copper and mercury: implications for the Maximum Permissible Concentrations and Negligible Concentrations in water, sediment and soil

NARCIS (Netherlands)

Smit CE; Wezel AP van; Jager T; Traas TP; CSR

2000-01-01

The impact of secondary poisoning on the Maximum Permissible Concentrations (MPCs) and Negligible Concentrations (NCs) of cadmium, copper and mercury in water, sediment and soil have been evaluated. Field data on accumulation of these elements by fish, mussels and earthworms were used to derive

49 CFR 192.623 - Maximum and minimum allowable operating pressure; Low-pressure distribution systems.

Science.gov (United States)

2010-10-01

... distribution systems. (a) No person may operate a low-pressure distribution system at a pressure high enough to...) No person may operate a low pressure distribution system at a pressure lower than the minimum... 49 Transportation 3 2010-10-01 2010-10-01 false Maximum and minimum allowable operating pressure...

Simplified method of checking the observance of maximum permissible activity of waste forms to be placed in the Konrad shaft for final waste storage

International Nuclear Information System (INIS)

Berg, H.P.; Piefke, F.

1986-10-01

The requirements to be met by waste forms destined for final storage in the Konrad shaft among others define maximum permissible activity levels which have been determined from the various parts of the safety analyses. For waste forms with very low activity levels, it is suitable to compile all the very specific requirements in one checking list, and to perform the checking as simply as adequate. On the basis of the compilation of requirements defined for normal operation of the storage facility, hypothetical accidents, thermal loads affecting the host rock, and criticality safety, the maximum permissible activities are derived that are to be checked by the simplified control measures explained. The report explains the computer programs for the ANKONA code. (orig.) [de

MAK and BAT values list 2017. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2017-01-01

The MAK and BAT values list 2017 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

MAK and BAT values list 2016. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2016-01-01

The MAK and BAT values list 2016 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

Pressure transmission area and maximum pressure transmission of different thermoplastic resin denture base materials under impact load.

Science.gov (United States)

Nasution, Hubban; Kamonkhantikul, Krid; Arksornnukit, Mansuang; Takahashi, Hidekazu

2018-01-01

The purposes of the present study were to examine the pressure transmission area and maximum pressure transmission of thermoplastic resin denture base materials under an impact load, and to evaluate the modulus of elasticity and nanohardness of thermoplastic resin denture base. Three injection-molded thermoplastic resin denture base materials [polycarbonate (Basis PC), ethylene propylene (Duraflex), and polyamide (Valplast)] and one conventional heat-polymerized acrylic resin (PMMA, SR Triplex Hot) denture base, all with a mandibular first molar acrylic resin denture tooth set in were evaluated (n=6). Pressure transmission area and maximum pressure transmission of the specimens under an impact load were observed by using pressure-sensitive sheets. The modulus of elasticity and nanohardness of each denture base (n=10) were measured on 15×15×15×3mm 3 specimen by using an ultramicroindentation system. The pressure transmission area, modulus of elasticity, and nanohardness data were statistically analyzed with 1-way ANOVA, followed by Tamhane or Tukey HSD post hoc test (α=.05). The maximum pressure transmission data were statistically analyzed with Kruskal-Wallis H test, followed by Mann-Whitney U test (α=.05). Polymethyl methacrylate showed significantly larger pressure transmission area and higher maximum pressure transmission than the other groups (Pelasticity and nanohardness among the four types of denture bases (Pelasticity and nanohardness of each type of denture base were demonstrated. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

49 CFR 192.619 - Maximum allowable operating pressure: Steel or plastic pipelines.

Science.gov (United States)

2010-10-01

... plastic pipelines. 192.619 Section 192.619 Transportation Other Regulations Relating to Transportation... Operations § 192.619 Maximum allowable operating pressure: Steel or plastic pipelines. (a) No person may operate a segment of steel or plastic pipeline at a pressure that exceeds a maximum allowable operating...

Releasable activity and maximum permissible leakage rate within a transport cask of Tehran Research Reactor fuel samples

Directory of Open Access Journals (Sweden)

Rezaeian Mahdi

2015-01-01

Full Text Available Containment of a transport cask during both normal and accident conditions is important to the health and safety of the public and of the operators. Based on IAEA regulations, releasable activity and maximum permissible volumetric leakage rate within the cask containing fuel samples of Tehran Research Reactor enclosed in an irradiated capsule are calculated. The contributions to the total activity from the four sources of gas, volatile, fines, and corrosion products are treated separately. These calculations are necessary to identify an appropriate leak test that must be performed on the cask and the results can be utilized as the source term for dose evaluation in the safety assessment of the cask.

Effect of Training Frequency on Maximum Expiratory Pressure

Science.gov (United States)

Anand, Supraja; El-Bashiti, Nour; Sapienza, Christine

2012-01-01

Purpose: To determine the effects of expiratory muscle strength training (EMST) frequency on maximum expiratory pressure (MEP). Method: We assigned 12 healthy participants to 2 groups of training frequency (3 days per week and 5 days per week). They completed a 4-week training program on an EMST trainer (Aspire Products, LLC). MEP was the primary…

MAK and BAT values list 2015. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2015. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-11-01

The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2015 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

MAK and BAT values list 2014. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2014. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

Energy Technology Data Exchange (ETDEWEB)

NONE

2014-11-01

The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2014 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

MAK and BAT values list 2013. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2013. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-01

The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2013 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

Experimental verification of the imposing principle for maximum permissible levels of multicolor laser radiation

Directory of Open Access Journals (Sweden)

Ivashin V.A.

2013-12-01

Full Text Available Aims. The study presents the results of experimental research to verify the principle overlay for maximum permissible levels (MPL of multicolor laser radiation single exposure on eyes. This principle of the independence of the effects of radiation with each wavelength (the imposing principle, was founded and generalized to a wide range of exposure conditions. Experimental verification of this approach in relation to the impact of laser radiation on tissue fundus of an eye, as shows the analysis of the literature was not carried out. Material and methods. Was used in the experimental laser generating radiation with wavelengths: Л1 =0,532 microns, A2=0,556to 0,562 microns and A3=0,619to 0,621 urn. Experiments were carried out on eyes of rabbits with evenly pigmented eye bottom. Results. At comparison of results of processing of the experimental data with the calculated data it is shown that these levels are close by their parameters. Conclusions. For the first time in the Russian Federation had been performed experimental studies on the validity of multi-colored laser radiation on the organ of vision. In view of the objective coincidence of the experimental data with the calculated data, we can conclude that the mathematical formulas work.

46 CFR 115.700 - Permission for repairs and alterations.

Science.gov (United States)

2010-10-01

... replacement in kind, of electrical wiring, fuel lines, tanks, boilers and other pressure vessels, and steering... 46 Shipping 4 2010-10-01 2010-10-01 false Permission for repairs and alterations. 115.700 Section... AND CERTIFICATION Repairs and Alterations § 115.700 Permission for repairs and alterations. (a...

Further European initiatives and regulations concerning radiation protection: drinking water guideline, maximum permissible contamination in food products and feeding stuff

International Nuclear Information System (INIS)

Mundigl, Stefan

2013-01-01

The radiation protection community has observed intensively the development of basic safety standards concerning protection against hazards of ionizing radiation. The new core part of the European radiation protection legislation is complemented by several specialized regulations relevant for radiation protection. Besides the existing regulations in the field of emergency protection the European Commission initiated a drinking water guideline that will be published in the near future. Furthermore the European commission approved a revised regulation concerning the maximum permissible contamination limits for food products and feeding stuff in case of a future nuclear accident. Together with the new radiation protection basic standards a new complete, coherent and modernized European regulation package will be accomplished.

Blood-pressure-independent wall thickening of intramyocardial arterioles in experimental uraemia: evidence for a permissive action of PTH.

Science.gov (United States)

Amann, K; Törnig, J; Flechtenmacher, C; Nabokov, A; Mall, G; Ritz, E

1995-11-01

Abnormalities in cardiovascular structures, e.g. LV hypertrophy and thickening of vessels (arteries, arterioles, veins) are hallmarks of renal failure. They are in part independent of elevated blood pressure. Parathyroid hormone (PTH) has been shown to affect cardiac function and has also been identified as a permissive factor in the genesis of cardiac fibrosis. The present study in rats with experimental renal failure was designed to examine whether PTH was permissive for wall thickening of intramyocardial arterioles as well. Male SD rats were sham operated or subtotally nephrectomized and maintained for 2 weeks. Subgroups of subtotally nephrectomized (SNX) rats were parathyroidectomized (PTX). Saline or rat 1, 34 PTH was administered by osmotic minipump. Eucalcaemia was maintained in PTX animals by a high-calcium diet (3%). Serum calcium was not statistically different between the groups. After perfusion fixation, intramyocardial arterioles were assessed using stereological techniques (wall thickness; wall/lumen ratio; minimal lumen diameter; length density). In random samples of the left ventricle, wall thickness of arterioles was 2.2 +/- 0.25 microns in sham-op controls and 2.76 +/- 0.41 in SNX (n = at least 8 animals per group). SNX-PTX animals+solvent did not differ significantly from sham-op controls (2.08 +/- 0.42 microns), while SNX-PTX animals+PTH had values not significantly different from SNX (2.59 +/- 0.54 microns). Differences in wall thickness were not paralleled by differences in systolic blood pressure (sham-op 110 +/- 13.3 mmHg; SNX 138 +/- 8.4 mmHg, SNX-PTX+solvent 142 +/- 5.2 mmHg; SNX-PTX+PTH 148 +/- 5.7 mmHg). PTH treated animals showed signs of marked vascular smooth-muscle cell and endothelial-cell activation. The data suggest that wall thickening of intramyocardial arterioles in short-term experimental uraemia is dependent upon the presence of PTH (permissive effect).

The role of pressure anisotropy on the maximum mass of cold ...

Indian Academy of Sciences (India)

,. Pune 411 007, India. 3 ... red-shift and mass increase in the presence of anisotropic pressures; numerical values are generated which are in ... that anisotropy may also change the limiting values of the maximum mass of com- pact stars.

Biological bases of the maximum permissible exposure levels of the UK laser standard BS 4803: 1983

International Nuclear Information System (INIS)

McKinlay, A.F.; Harlen, F.

1983-10-01

The use of lasers has increased greatly over the past 15 years or so, to the extent that they are now used routinely in many occupational and public situations. There has been an increasing awareness of the potential hazards presented by lasers and substantial efforts have been made to formulate safety standards. In the UK the relevant Safety Standard is the British Standards Institution Standard BS 4803. This Standard was originally published in 1972 and a revision has recently been published (BS 4803: 1983). The revised standard has been developed using the American National Standards Institute Standard, ANSI Z136.1 (1973 onwards), as a model. In other countries, national standards have been similarly formulated, resulting in a large measure of international agreement through participation in the work of the International Electrotechnical Commission (IEC). The bases of laser safety standards are biophysical data on threshold injury effects, particularly on the retina, and the development of theoretical models of damage mechanisms. This report deals in some detail with the mechanisms of injury from over exposure to optical radiations, in particular with the dependency of the type and degree of damage on wavelength, image size and pulse duration. The maximum permissible exposure levels recommended in BS 4803: 1983 are compared with published data for damage thresholds and the adequacy of the standard is discussed. (author)

Maximum home blood pressure is a useful indicator of diabetic nephropathy in patients with type 2 diabetes mellitus: KAMOGAWA-HBP study.

Science.gov (United States)

Oyabu, Chikako; Ushigome, Emi; Matsumoto, Shinobu; Tanaka, Toru; Hasegawa, Goji; Nakamura, Naoto; Ohnishi, Masayoshi; Tsunoda, Sei; Ushigome, Hidetaka; Yokota, Isao; Tanaka, Muhei; Asano, Mai; Yamazaki, Masahiro; Fukui, Michiaki

2017-11-01

Maximum home systolic blood pressure has been shown to predict target organ damage. We aimed to clarify the association between maximum home systolic blood pressure and urine albumin to creatinine ratio, an indicator of early-phase diabetic nephropathy in patients with type 2 diabetes. In 1040 patients, we assessed the relationship of mean or maximum home systolic blood pressure and urine albumin to creatinine ratio, and compared the area under the receiver operating characteristic curve of mean or maximum home systolic blood pressure for diabetic nephropathy (urine albumin to creatinine ratio ⩾30 mg/g Cr). Multivariate linear regression analyses indicated that mean morning systolic blood pressure ( β = 0.010, p blood pressure ( β = 0.008, p blood pressure was 0.667 (0.634-0.700; p blood pressure, as well as mean home systolic blood pressure, was significantly associated with diabetic nephropathy in patients with type 2 diabetes.

MAK and BAT values list 2017. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2017. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

Energy Technology Data Exchange (ETDEWEB)

NONE

2017-08-01

The MAK and BAT values list 2017 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

Effect of Ovality on Maximum External Pressure of Helically Coiled Steam Generator Tubes with a Rectangular Wear

Energy Technology Data Exchange (ETDEWEB)

Shin, Dong In; Lim, Eun Mo; Huh, Nam Su [Seoul National Univ. of Science and Technology, Seoul (Korea, Republic of); Choi, Shin Beom; Yu, Je Yong; Kim, Ji Ho; Choi, Suhn [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

A structural integrity of steam generator tubes of nuclear power plants is one of crucial parameters for safe operation of nuclear power plants. Thus, many studies have been made to provide engineering methods to assess integrity of defective tubes of commercial nuclear power plants considering its operating environments and defect characteristics. As described above, the geometric and operating conditions of steam generator tubes in integral reactor are significantly different from those of commercial reactor. Therefore, the structural integrity assessment of defective tubes of integral reactor taking into account its own operating conditions and geometric characteristics, i. e., external pressure and helically coiled shape, should be made to demonstrate compliance with the current design criteria. Also, ovality is very specific characteristics of the helically coiled tube because it is occurred during the coiling processes. The wear, occurring from FIV (Flow Induced Vibration) and so on, is main degradation of steam generator tube. In the present study, maximum external pressure of helically coiled steam generator tube with wear is predicted based on the detailed 3-dimensional finite element analysis. As for shape of wear defect, the rectangular shape is considered. In particular, the effect of ovality on the maximum external pressure of helically coiled tubes with rectangular shaped wear is investigated. In the present work, the maximum external pressure of helically coiled steam generator tube with rectangular shaped wear is investigated via detailed 3-D FE analyses. In order to cover a practical range of geometries for defective tube, the variables affecting the maximum external pressure were systematically varied. In particular, the effect of tube ovality on the maximum external pressure is evaluated. It is expected that the present results can be used as a technical backgrounds for establishing a practical structural integrity assessment guideline of

Approximation for maximum pressure calculation in containment of PWR reactors

International Nuclear Information System (INIS)

Souza, A.L. de

1989-01-01

A correlation was developed to estimate the maximum pressure of dry containment of PWR following a Loss-of-Coolant Accident - LOCA. The expression proposed is a function of the total energy released to the containment by the primary circuit, of the free volume of the containment building and of the total surface are of the heat-conducting structures. The results show good agreement with those present in Final Safety Analysis Report - FSAR of several PWR's plants. The errors are in the order of ± 12%. (author) [pt

Determing and monitoring of maximum permissible power for HWRR-3

International Nuclear Information System (INIS)

Jia Zhanli; Xiao Shigang; Jin Huajin; Lu Changshen

1987-01-01

The operating power of a reactor is an important parameter to be monitored. This report briefly describes the determining and monitoring of maximum permissiable power for HWRR-3. The calculating method is described, and the result of calculation and analysis of error are also given. On-line calculation and real time monitoring have been realized at the heavy water reactor. It provides the reactor with a real time and reliable supervision. This makes operation convenient and increases reliability

[Effect of maximum blood pressure fluctuation on prognosis of patients with acute ischemic stroke within 24 hours after hospital admission].

Science.gov (United States)

Wang, H; Tang, Y; Zhang, Y; Xu, K; Zhao, J B

2018-05-10

Objective: To investigate the relationship between the maximum blood pressure fluctuation within 24 hours after admission and the prognosis at discharge. Methods: The patients with ischemic stroke admitted in Department of Neurology of the First Affiliated Hospital of Harbin Medical University within 24 hours after onset were consecutively selected from April 2016 to March 2017. The patients were grouped according to the diagnostic criteria of hypertension. Ambulatory blood pressure of the patients within 24 hours after admission were measured with bedside monitors and baseline data were collected. The patients were scored by NIHSS at discharge. The relationships between the maximum values of systolic blood pressure (SBP) or diastolic blood pressure (DBP) and the prognosis at discharge were analyzed. Results: A total of 521 patients with acute ischemic stroke were enrolled. They were divided into normal blood pressure group (82 cases) and hypertension group(439 cases). In normal blood pressure group, the maximum values of SBP and DBP were all in normal distribution ( P >0.05). The maximum value of SBP fluctuation was set at 146.6 mmHg. After adjustment for potential confounders, the OR for poor prognosis at discharge in patients with SBP fluctuation ≥146.6 mmHg was 2.669 (95 %CI : 0.594-11.992) compared with those with SBP fluctuation blood pressure at admission, the maximum values of SBP and DBP within 24 hours after admission had no relationship with prognosis at discharge. In acute ischemic stroke patients with hypertension at admission, the maximum values of SBP and DBP within 24 hours after admission were associated with poor prognosis at discharge.

An investigation on effects of amputee's physiological parameters on maximum pressure developed at the prosthetic socket interface using artificial neural network.

Science.gov (United States)

Nayak, Chitresh; Singh, Amit; Chaudhary, Himanshu; Unune, Deepak Rajendra

2017-10-23

Technological advances in prosthetics have attracted the curiosity of researchers in monitoring design and developments of the sockets to sustain maximum pressure without any soft tissue damage, skin breakdown, and painful sores. Numerous studies have been reported in the area of pressure measurement at the limb/socket interface, though, the relation between amputee's physiological parameters and the pressure developed at the limb/socket interface is still not studied. Therefore, the purpose of this work is to investigate the effects of patient-specific physiological parameters viz. height, weight, and stump length on the pressure development at the transtibial prosthetic limb/socket interface. Initially, the pressure values at the limb/socket interface were clinically measured during stance and walking conditions for different patients using strain gauges placed at critical locations of the stump. The measured maximum pressure data related to patient's physiological parameters was used to develop an artificial neural network (ANN) model. The effects of physiological parameters on the pressure development at the limb/socket interface were examined using the ANN model. The analyzed results indicated that the weight and stump length significantly affects the maximum pressure values. The outcomes of this work could be an important platform for the design and development of patient-specific prosthetic socket which can endure the maximum pressure conditions at stance and ambulation conditions.

Permissive hypotension in the extremely low birthweight infant with signs of good perfusion.

LENUS (Irish Health Repository)

Dempsey, E M

2012-01-31

INTRODUCTION: Many practitioners routinely treat infants whose mean arterial blood pressure in mm Hg is less than their gestational age in weeks (GA). OBJECTIVE: To assess the effectiveness of utilising a combined approach of clinical signs, metabolic acidosis and absolute blood pressure (BP) values when deciding to treat hypotension in the extremely low birthweight (ELBW) infant. METHODS: Retrospective cohort study of all live born ELBW infants admitted to our neonatal intensive care unit over a 4-year period. Patients were grouped as either normotensive (BP never less than GA), hypotensive and not treated (BPpermissive hypotension) and hypotensive treated (BPpressure data were available on 108 patients. 53% of patients were hypotensive (mean BP in mm Hg less than GA in weeks). Treated patients had lower birth weight and GA, and significantly lower blood pressure at 6, 12, 18 and 24 h. Normotensive patients and patients designated as having permissive hypotension had similar outcomes. Mean blood pressure in the permissive group increased from 26 mm Hg at 6 h to 31 mm Hg at 24 h. In a logistic regression model, treated hypotension is independently associated with mortality, odds ratio 8.0 (95% CI 2.3 to 28, p<0.001). CONCLUSIONS: Blood pressure spontaneously improves in ELBW infants during the first 24 h. Infants hypotensive on GA criteria but with clinical evidence of good perfusion had as good an outcome as normotensive patients. Treated low blood pressure was associated with adverse outcome.

Local wall thickness reductions in operative high-pressure gas pipelines; Lokale Wanddickenminderungen an in Betrieb befindlichen Gashochdruckleitungen

Energy Technology Data Exchange (ETDEWEB)

Hass, Georg [Netzdienste Rhein-Main GmbH, Frankfurt am Main (Germany); Hoffmann, Ulrich [Verbundnetz Gas AG (VNG), Leipzig (Germany); Konarske, Juergen [RWE Westfalen-Weser-Ems Netzservice GmbH, Recklinghausen (Germany); Soppa, Thorsten [NG Netz Gas+Wasser (Germany); Steiner, Michael [Open Grid Europe GmbH, Essen (Germany)

2011-04-15

TUeV Nord, Salzgitter Mannesmann Forschung and DVGW investigated methods to assess local wall thickness reductions in operative high-pressure gas pipelines. Methods described in the relevant literature were reviewed with regard to the limiting criteria defined for maximum permissible wall thickness reductions. (orig./GL)

Boiling-up of a liquid in a large volume at fast pressure drop

International Nuclear Information System (INIS)

Isaev, O.A.; Pavlov, P.A.

1980-01-01

Experiment results on sharp pressure drop in overheated water and carbon dioxide are presented. Pressure fields are investigated upon seal failure of the tube for various initial temperatures varying in the 0.57-0.97 interval on critical temperature. The depth of the liOuid inlet into the metastable region can be compared with maximum permissible superheating of a pure liquid. The applicability of fluctuation embrion formation for pressure calculation in the initial phase of explosive boiling-up at seal failure of the system is considered. The nature of boiling centers origin is discussed

Considerations on the establishment of maximum permissible exposure of man

International Nuclear Information System (INIS)

Jacobi, W.

1974-01-01

An attempt is made in the information lecture to give a quantitative analysis of the somatic radiation risk and to illustrate a concept to fix dose limiting values. Of primary importance is the limiting values. Of primary importance is the limiting value of the radiation exposure to the whole population. By consequential application of the risk concept, the following points are considered: 1) Definition of the risk for radiation late damages (cancer, leukemia); 2) relationship between radiation dose and thus caused radiation risk; 3) radiation risk and the dose limiting values at the time; 4) criteria for the maximum acceptable radiation risk; 5) limiting value which can be expected at the time. (HP/LH) [de

Rate maximum calculation of Dpa in CNA-II pressure vessel

International Nuclear Information System (INIS)

Mascitti, J. A

2012-01-01

The maximum dpa rate was calculated for the reactor in the following state: fresh fuel, no Xenon, a Boron concentration of 15.3 ppm, critical state, its control rods in the criticality position, hot, at full power (2160 MW). It was determined that the maximum dpa rate under such conditions is 3.54(2)x10 12 s -1 and it is located in the positions corresponding to θ=210 o in the azimuthal direction, and z=20 cm and -60 cm respectively in the axial direction, considering the calculation mesh centered at half height of the fuel element (FE) active length. The dpa rate spectrum was determined as well as the contribution to it for 4 energy groups: a thermal group, two epithermal groups and a fast one. The maximum dpa rate considering the photo-neutrons production from (γ, n) reaction in the heavy water of coolant and moderator was 3.93(4)x10 12 s -1 that is 11% greater than the obtained without photo-neutrons. This verified significant difference between both cases, suggest that photo-neutrons in large heavy water reactors such as CNA-II should not be ignored. The maximum DPA rate in the first mm of the reactor pressure vessel was calculated too and it was obtained a value of 4.22(6)x10 12 s -1 . It should be added that the calculation was carried out with the reactor complete accurate model, with no approximations in spatial or energy variables. Each value has, between parentheses, a percentage relative error representing the statistical uncertainty due to the probabilistic Monte Carlo method used to estimate it. More representative values may be obtained with this method if equilibrium burn-up distribution is used (author)

Parental feeding practices predict authoritative, authoritarian, and permissive parenting styles.

Science.gov (United States)

Hubbs-Tait, Laura; Kennedy, Tay Seacord; Page, Melanie C; Topham, Glade L; Harrist, Amanda W

2008-07-01

Our goal was to identify how parental feeding practices from the nutrition literature link to general parenting styles from the child development literature to understand how to target parenting practices to increase effectiveness of interventions. Stand-alone parental feeding practices could be targeted independently. However, parental feeding practices linked to parenting styles require interventions treating underlying family dynamics as a whole. To predict parenting styles from feeding practices and to test three hypotheses: restriction and pressure to eat are positively related whereas responsibility, monitoring, modeling, and encouraging are negatively related to an authoritarian parenting style; responsibility, monitoring, modeling, and encouraging are positively related whereas restriction and pressure to eat are negatively related to an authoritative parenting style; a permissive parenting style is negatively linked with all six feeding practices. Baseline data of a randomized-controlled intervention study. Two hundred thirty-nine parents (93.5% mothers) of first-grade children (134 boys, 105 girls) enrolled in rural public schools. Parental responses to encouraging and modeling questionnaires and the Child Feeding Questionnaire, as well as parenting styles measured by the Parenting Styles and Dimensions Questionnaire. Correlation and regression analyses. Feeding practices explained 21%, 15%, and 8% of the variance in authoritative, authoritarian, and permissive parenting, respectively. Restriction, pressure to eat, and monitoring (negative) significantly predicted an authoritarian style (Hypothesis 1); responsibility, restriction (negative), monitoring, and modeling predicted an authoritative style (Hypothesis 2); and modeling (negative) and restriction significantly predicted a permissive style (Hypothesis 3). Parental feeding practices with young children predict general parenting styles. Interventions that fail to address underlying parenting styles

Pressurizer /Auxiliary Spray Piping Stress Analysis For Determination Of Lead Shielding Maximum Allow Able Load

International Nuclear Information System (INIS)

Setjo, Renaningsih

2000-01-01

Piping stress analysis for PZR/Auxiliary Spray Lines Nuclear Power Plant AV Unit I(PWR Type) has been carried out. The purpose of this analysis is to establish a maximum allowable load that is permitted at the time of need by placing lead shielding on the piping system on class 1 pipe, Pressurizer/Auxiliary Spray Lines (PZR/Aux.) Reactor Coolant Loop 1 and 4 for NPP AV Unit one in the mode 5 and 6 during outage. This analysis is intended to reduce the maximum amount of radiation dose for the operator during ISI ( In service Inspection) period.The result shown that the maximum allowable loads for 4 inches lines for PZR/Auxiliary Spray Lines is 123 lbs/feet

Study on Droplet Size and Velocity Distributions of a Pressure Swirl Atomizer Based on the Maximum Entropy Formalism

Directory of Open Access Journals (Sweden)

Kai Yan

2015-01-01

Full Text Available A predictive model for droplet size and velocity distributions of a pressure swirl atomizer has been proposed based on the maximum entropy formalism (MEF. The constraint conditions of the MEF model include the conservation laws of mass, momentum, and energy. The effects of liquid swirling strength, Weber number, gas-to-liquid axial velocity ratio and gas-to-liquid density ratio on the droplet size and velocity distributions of a pressure swirl atomizer are investigated. Results show that model based on maximum entropy formalism works well to predict droplet size and velocity distributions under different spray conditions. Liquid swirling strength, Weber number, gas-to-liquid axial velocity ratio and gas-to-liquid density ratio have different effects on droplet size and velocity distributions of a pressure swirl atomizer.

Permission Marketing and Privacy Concerns - Why Do Customers (Not) Grant Permissions?

NARCIS (Netherlands)

Krafft, Manfred; Arden, Christine M.; Verhoef, Peter C.

Little is known about the influence of motivators that drive consumers to grant permission to be contacted via personalized communication. In this study, a framework is developed to investigate the effect of select drivers of consumers granting permission to receive personalized messages. The

The Influence of Pressure Distribution on the Maximum Values of Stress in FEM Analysis of Plain Bearings

Directory of Open Access Journals (Sweden)

Vasile Cojocaru

2016-12-01

Full Text Available Several methods can be used in the FEM studies to apply the loads on a plain bearing. The paper presents a comparative analysis of maximum stress obtained for three loading scenarios: resultant force applied on the shaft – bearing assembly, variable pressure with sinusoidal distribution applied on the bearing surface, variable pressure with parabolic distribution applied on the bearing surface.

Radiation pressure acceleration: The factors limiting maximum attainable ion energy

Energy Technology Data Exchange (ETDEWEB)

Bulanov, S. S.; Esarey, E.; Schroeder, C. B. [Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Bulanov, S. V. [KPSI, National Institutes for Quantum and Radiological Science and Technology, Kizugawa, Kyoto 619-0215 (Japan); A. M. Prokhorov Institute of General Physics RAS, Moscow 119991 (Russian Federation); Esirkepov, T. Zh.; Kando, M. [KPSI, National Institutes for Quantum and Radiological Science and Technology, Kizugawa, Kyoto 619-0215 (Japan); Pegoraro, F. [Physics Department, University of Pisa and Istituto Nazionale di Ottica, CNR, Pisa 56127 (Italy); Leemans, W. P. [Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Physics Department, University of California, Berkeley, California 94720 (United States)

2016-05-15

Radiation pressure acceleration (RPA) is a highly efficient mechanism of laser-driven ion acceleration, with near complete transfer of the laser energy to the ions in the relativistic regime. However, there is a fundamental limit on the maximum attainable ion energy, which is determined by the group velocity of the laser. The tightly focused laser pulses have group velocities smaller than the vacuum light speed, and, since they offer the high intensity needed for the RPA regime, it is plausible that group velocity effects would manifest themselves in the experiments involving tightly focused pulses and thin foils. However, in this case, finite spot size effects are important, and another limiting factor, the transverse expansion of the target, may dominate over the group velocity effect. As the laser pulse diffracts after passing the focus, the target expands accordingly due to the transverse intensity profile of the laser. Due to this expansion, the areal density of the target decreases, making it transparent for radiation and effectively terminating the acceleration. The off-normal incidence of the laser on the target, due either to the experimental setup, or to the deformation of the target, will also lead to establishing a limit on maximum ion energy.

Critical Assessment of the Surface Tension determined by the Maximum Pressure Bubble Method

OpenAIRE

Benedetto, Franco Emmanuel; Zolotucho, Hector; Prado, Miguel Oscar

2015-01-01

The main factors that influence the value of surface tension of a liquid measured with the Maximum Pressure Bubble Method are critically evaluated. We present experimental results showing the effect of capillary diameter, capillary depth, bubble spheroidicity and liquid density at room temperature. We show that the decrease of bubble spheroidicity due to increase of capillary immersion depth is not sufficient to explain the deviations found in the measured surface tension values. Thus, we pro...

Prediction of vertical expansion pressure stresses in coke oven heating walls

Energy Technology Data Exchange (ETDEWEB)

Duerselen, H; Janicka, J

1987-08-01

The paper describes an accurate method developed by Krupp Koppers for calculating stresses in the central areas of coke oven heating walls. The results of this calculation model have provided the following conclusions for the design of coke ovens: 1) a rising pre-stressing of the heating walls caused by the weight of the top deck of the coke oven leads - compared with the stress limits of W. Ahlers - to lower permissible expansion pressures. 2) A given heating wall width has its corresponding maximum feasible oven height. Heating wall width and top deck weight are not interchangeable parameters. 3) The dependence of the permissible expansion pressure on the stretcher brick thickness should not be overlooked. Stretcher brick thicknesses of under 90 mm are not recomended for tall ovens and heavily swelling coal. 4) The capacity of mortar to absorb tensile stresses is ultimately an undesirable property, because the stresses at the points where the mortar is not holding are higher than in a straightforward stretch of brickwork.

Take control of permissions in Leopard

CERN Document Server

Tanaka, Brian

2009-01-01

Permissions problems got you down? Turn to Unix expert Brian Tanaka's unique guide to the permissions in Mac OS X 10.5 Leopard that control access to your files, folders, and disks. You'll learn how to keep files private, when to set Ignore Permissions, what happens when you repair permissions, how to delete stuck files, and the best ways to solve permissions-related problems. Advanced concepts include the sticky bit, Leopard's more-important access control lists, bit masks, and symbolic versus absolute ways to set permissions. The book covers how to take control of permissions via the Finder

Mechanical solution of the maximum point of dynamic abutment pressure under deep long-wall working face

Energy Technology Data Exchange (ETDEWEB)

Jiang, F.; Ma, Q. [Shandong University of Science and Technology, Tai' an (China). College of Resource and Environmental Engineering

2002-06-01

The paper studies the dynamic relationship between abutment pressure and overburden collapse precess with advancing of working face. The result shows that the abutment pressure reaches its maximum value when the working face dimension is 1.27 times of the mining depth. This result confirms the statistical result from the strata movement surveys that overburden reaches its full movement stage when extracting dimension reaches 1.2 1.4 times of the mining depth. 12 refs., 2 figs.

38 CFR 36.4204 - Loan purposes, maximum loan amounts and terms.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Loan purposes, maximum loan amounts and terms. 36.4204 Section 36.4204 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF... constructing a suitable pad for the manufactured home. (e) The maximum permissible loan terms shall not exceed...

Numerical estimates of the maximum sustainable pore pressure in anticline formations using the tensor based concept of pore pressure-stress coupling

Directory of Open Access Journals (Sweden)

Andreas Eckert

2015-02-01

Full Text Available The advanced tensor based concept of pore pressure-stress coupling is used to provide pre-injection analytical estimates of the maximum sustainable pore pressure change, ΔPc, for fluid injection scenarios into generic anticline geometries. The heterogeneous stress distribution for different prevailing stress regimes in combination with the Young's modulus (E contrast between the injection layer and the cap rock and the interbedding friction coefficient, μ, may result in large spatial and directional differences of ΔPc. A single value characterizing the cap rock as for horizontal layered injection scenarios is not obtained. It is observed that a higher Young's modulus in the cap rock and/or a weak mechanical coupling between layers amplifies the maximum and minimum ΔPc values in the valley and limb, respectively. These differences in ΔPc imposed by E and μ are further amplified by different stress regimes. The more compressional the stress regime is, the larger the differences between the maximum and minimum ΔPc values become. The results of this study show that, in general compressional stress regimes yield the largest magnitudes of ΔPc and extensional stress regimes provide the lowest values of ΔPc for anticline formations. Yet this conclusion has to be considered with care when folded anticline layers are characterized by flexural slip and the friction coefficient between layers is low, i.e. μ = 0.1. For such cases of weak mechanical coupling, ΔPc magnitudes may range from 0 MPa to 27 MPa, indicating imminent risk of fault reactivation in the cap rock.

Maximum magnitude of injection-induced earthquakes: A criterion to assess the influence of pressure migration along faults

Science.gov (United States)

Norbeck, Jack H.; Horne, Roland N.

2018-05-01

The maximum expected earthquake magnitude is an important parameter in seismic hazard and risk analysis because of its strong influence on ground motion. In the context of injection-induced seismicity, the processes that control how large an earthquake will grow may be influenced by operational factors under engineering control as well as natural tectonic factors. Determining the relative influence of these effects on maximum magnitude will impact the design and implementation of induced seismicity management strategies. In this work, we apply a numerical model that considers the coupled interactions of fluid flow in faulted porous media and quasidynamic elasticity to investigate the earthquake nucleation, rupture, and arrest processes for cases of induced seismicity. We find that under certain conditions, earthquake ruptures are confined to a pressurized region along the fault with a length-scale that is set by injection operations. However, earthquakes are sometimes able to propagate as sustained ruptures outside of the zone that experienced a pressure perturbation. We propose a faulting criterion that depends primarily on the state of stress and the earthquake stress drop to characterize the transition between pressure-constrained and runaway rupture behavior.

Measurement of the surface tension by the method of maximum gas bubble pressure

International Nuclear Information System (INIS)

Dugne, Jean

1971-01-01

A gas bubble method for measuring surface tension was studied. Theoretical investigations demonstrated that the maximum pressure can be represented by the envelope of a certain family of curves and that the physical nature of the capillary tube imposes an upper limit to its useful radius. With a given tube and a specified liquid, the dynamic evolution of the gas bubble depends only upon the variation of the mass of gas contained with time; this fact may restrict the choice of tubes. The use of one single tube requires important corrections. Computer treatment of the problem led to some accurate equations for calculating γ. Schroedinger equations and Sudgen's table are examined. The choice of tubes, the necessary corrections, density measurement, and the accuracy attainable are discussed. Experiments conducted with water and mercury using the sessile drop method and continuous recording of the pressure verified the theoretical ideas. (author) [fr

Maximum permissible concentrations and negligible concentrations for phthalates (dibutylphthalate and di(2-ethylhexyl)phthlate), with emphasis on endocrine disruptive properties

NARCIS (Netherlands)

Wezel AP van; Posthumus R; Vlaardingen P van; Crommentuijn T; Plassche EJ van de; CSR

This report presents maximal permissible concentrations (MPCs) and negligible concentrations (NCs) are derived for di-n-butylphthalate (DBP) and di(2-ethylhexyl)phthalate (DEHP). Phthalates are often mentioned as suspected endocrine disrupters. Data with endpoints related to the endocrine or

Permissible Delay in Payments

Directory of Open Access Journals (Sweden)

Yung-Fu Huang

2007-01-01

Full Text Available The main purpose of this paper wants to investigate the optimal retailer's lot-sizing policy with two warehouses under partially permissible delay in payments within the economic order quantity (EOQ framework. In this paper, we want to extend that fully permissible delay in payments to the supplier would offer the retailer partially permissible delay in payments. That is, the retailer must make a partial payment to the supplier when the order is received. Then the retailer must pay off the remaining balance at the end of the permissible delay period. In addition, we want to add the assumption that the retailer's storage space is limited. That is, the retailer will rent the warehouse to store these exceeding items when the order quantity is larger than retailer's storage space. Under these conditions, we model the retailer's inventory system as a cost minimization problem to determine the retailer's optimal cycle time and optimal order quantity. Three theorems are developed to efficiently determine the optimal replenishment policy for the retailer. Finally, numerical examples are given to illustrate these theorems and obtained a lot of managerial insights.

Android Multi-Level System Permission Management Approach

OpenAIRE

Luo, Yang; Zhang, Qixun; Shen, Qingni; Liu, Hongzhi; Wu, Zhonghai

2017-01-01

With the expansion of the market share occupied by the Android platform, security issues (especially application security) have become attention focus of researchers. In fact, the existing methods lack the capabilities to manage application permissions without root privilege. This study proposes a dynamic management mechanism of Android application permissions based on security policies. The paper first describes the permissions by security policies, then implementes permission checking code ...

Maximum Expected Wall Heat Flux and Maximum Pressure After Sudden Loss of Vacuum Insulation on the Stratospheric Observatory for Infrared Astronomy (SOFIA) Liquid Helium (LHe) Dewars

Science.gov (United States)

Ungar, Eugene K.

2014-01-01

The aircraft-based Stratospheric Observatory for Infrared Astronomy (SOFIA) is a platform for multiple infrared observation experiments. The experiments carry sensors cooled to liquid helium (LHe) temperatures. A question arose regarding the heat input and peak pressure that would result from a sudden loss of the dewar vacuum insulation. Owing to concerns about the adequacy of dewar pressure relief in the event of a sudden loss of the dewar vacuum insulation, the SOFIA Program engaged the NASA Engineering and Safety Center (NESC). This report summarizes and assesses the experiments that have been performed to measure the heat flux into LHe dewars following a sudden vacuum insulation failure, describes the physical limits of heat input to the dewar, and provides an NESC recommendation for the wall heat flux that should be used to assess the sudden loss of vacuum insulation case. This report also assesses the methodology used by the SOFIA Program to predict the maximum pressure that would occur following a loss of vacuum event.

Optimization study of pressure-swing distillation for the separation process of a maximum-boiling azeotropic system of water-ethylenediamine

Energy Technology Data Exchange (ETDEWEB)

Fulgueras, Alyssa Marie; Poudel, Jeeban; Kim, Dong Sun; Cho, Jungho [Kongju National University, Cheonan (Korea, Republic of)

2016-01-15

The separation of ethylenediamine (EDA) from aqueous solution is a challenging problem because its mixture forms an azeotrope. Pressure-swing distillation (PSD) as a method of separating azeotropic mixture were investigated. For a maximum-boiling azeotropic system, pressure change does not greatly affect the azeotropic composition of the system. However, the feasibility of using PSD was still analyzed through process simulation. Experimental vapor liquid equilibrium data of water-EDA system was studied to predict the suitability of thermodynamic model to be applied. This study performed an optimization of design parameters for each distillation column. Different combinations of operating pressures for the low- and high-pressure columns were used for each PSD simulation case. After the most efficient operating pressures were identified, two column configurations, low-high (LP+HP) and high-low (HP+ LP) pressure column configuration, were further compared. Heat integration was applied to PSD system to reduce low and high temperature utility consumption.

Optimization study of pressure-swing distillation for the separation process of a maximum-boiling azeotropic system of water-ethylenediamine

International Nuclear Information System (INIS)

Fulgueras, Alyssa Marie; Poudel, Jeeban; Kim, Dong Sun; Cho, Jungho

2016-01-01

The separation of ethylenediamine (EDA) from aqueous solution is a challenging problem because its mixture forms an azeotrope. Pressure-swing distillation (PSD) as a method of separating azeotropic mixture were investigated. For a maximum-boiling azeotropic system, pressure change does not greatly affect the azeotropic composition of the system. However, the feasibility of using PSD was still analyzed through process simulation. Experimental vapor liquid equilibrium data of water-EDA system was studied to predict the suitability of thermodynamic model to be applied. This study performed an optimization of design parameters for each distillation column. Different combinations of operating pressures for the low- and high-pressure columns were used for each PSD simulation case. After the most efficient operating pressures were identified, two column configurations, low-high (LP+HP) and high-low (HP+ LP) pressure column configuration, were further compared. Heat integration was applied to PSD system to reduce low and high temperature utility consumption.

Maximum permissible concentration of radon {sup 222}Rn in air; La concentration maximale admissible du radon 222 dans l'air

Energy Technology Data Exchange (ETDEWEB)

Hamard, J; Beau, P G; Ergas, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires, departement de la protection sanitaire, service d' hygiene atomique

1968-09-01

In order to verify the validity of the values proposed for the maximum permissible concentration of {sup 222}Rn in air, one can either approach the problem: - by epidemiological studies tending to determine the relation dose-effect both quantitatively and qualitatively; - or by choosing a lung model and clearance constants allowing a more accurate determination of the delivered dose and the localisation of the more severely irradiated portions of the bronchial tree. The radon MPC have been calculated using the model and the respiration constants set up by the I.C.R.P. Task Group on Lung dynamics. Two cases have been considered, i.e. when the radon daughter products behave as soluble materials and as insoluble ones. The values which have been found have been compared with those given up to now by several national and international bodies. (authors) [French] Deux voies d'approche peuvent etre empruntees pour verifier la validite des valeurs proposees pour la concentration maximale admissible du radon 222 dans l'air: - etudes epidemiologiques tendant a preciser qualitativement et quantitativement la relation dose-effet; - choix d'un modele pulmonaire et de constantes d'epuration permettant une determination plus precise de la dose delivree et la localisation des segments de l'arbre pulmonaire les plus irradies. Les auteurs ont utilise pour le calcul de la CMA du radon le modele et les constantes respiratoires proposees par le Task Group on Lungs dynamics de la C.I.P.R. On a pris en consideration le cas ou les descendants du radon se comportent comme des substances solubles et celui ou ils se comportent comme des substances insolubles. Les valeurs trouvees sont comparees a celles proposees jusqu'alors par divers organismes nationaux et internationaux. (auteurs)

Dynamic surface tension measurements of ionic surfactants using maximum bubble pressure tensiometry

Science.gov (United States)

Ortiz, Camilla U.; Moreno, Norman; Sharma, Vivek

Dynamic surface tension refers to the time dependent variation in surface tension, and is intimately linked with the rate of mass transfer of a surfactant from liquid sub-phase to the interface. The diffusion- or adsorption-limited kinetics of mass transfer to interfaces is said to impact the so-called foamability and the Gibbs-Marangoni elasticity of surfaces. Dynamic surface tension measurements carried out with conventional methods like pendant drop analysis, Wilhelmy plate, etc. are limited in their temporal resolution (>50 ms). In this study, we describe design and application of maximum bubble pressure tensiometry for the measurement of dynamic surface tension effects at extremely short (1-50 ms) timescales. Using experiments and theory, we discuss the overall adsorption kinetics of charged surfactants, paying special attention to the influence of added salt on dynamic surface tension.

30 CFR 62.130 - Permissible exposure level.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Permissible exposure level. 62.130 Section 62... REGULATIONS OCCUPATIONAL NOISE EXPOSURE § 62.130 Permissible exposure level. (a) The mine operator must assure that no miner is exposed during any work shift to noise that exceeds the permissible exposure level. If...

Simplified Methodology to Estimate the Maximum Liquid Helium (LHe) Cryostat Pressure from a Vacuum Jacket Failure

Science.gov (United States)

Ungar, Eugene K.; Richards, W. Lance

2015-01-01

The aircraft-based Stratospheric Observatory for Infrared Astronomy (SOFIA) is a platform for multiple infrared astronomical observation experiments. These experiments carry sensors cooled to liquid helium temperatures. The liquid helium supply is contained in large (i.e., 10 liters or more) vacuum-insulated dewars. Should the dewar vacuum insulation fail, the inrushing air will condense and freeze on the dewar wall, resulting in a large heat flux on the dewar's contents. The heat flux results in a rise in pressure and the actuation of the dewar pressure relief system. A previous NASA Engineering and Safety Center (NESC) assessment provided recommendations for the wall heat flux that would be expected from a loss of vacuum and detailed an appropriate method to use in calculating the maximum pressure that would occur in a loss of vacuum event. This method involved building a detailed supercritical helium compressible flow thermal/fluid model of the vent stack and exercising the model over the appropriate range of parameters. The experimenters designing science instruments for SOFIA are not experts in compressible supercritical flows and do not generally have access to the thermal/fluid modeling packages that are required to build detailed models of the vent stacks. Therefore, the SOFIA Program engaged the NESC to develop a simplified methodology to estimate the maximum pressure in a liquid helium dewar after the loss of vacuum insulation. The method would allow the university-based science instrument development teams to conservatively determine the cryostat's vent neck sizing during preliminary design of new SOFIA Science Instruments. This report details the development of the simplified method, the method itself, and the limits of its applicability. The simplified methodology provides an estimate of the dewar pressure after a loss of vacuum insulation that can be used for the initial design of the liquid helium dewar vent stacks. However, since it is not an exact

12 CFR 703.14 - Permissible investments.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Permissible investments. 703.14 Section 703.14 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING CREDIT UNIONS INVESTMENT AND DEPOSIT ACTIVITIES § 703.14 Permissible investments. (a) Variable rate investment. A Federal...

Social networks, leisure activities and maximum tongue pressure: cross-sectional associations in the Nagasaki Islands Study.

Science.gov (United States)

Nagayoshi, Mako; Higashi, Miho; Takamura, Noboru; Tamai, Mami; Koyamatsu, Jun; Yamanashi, Hirotomo; Kadota, Koichiro; Sato, Shimpei; Kawashiri, Shin-Ya; Koyama, Zenya; Saito, Toshiyuki; Maeda, Takahiro

2017-12-06

Social environment is often associated with health outcomes, but epidemiological evidence for its effect on oral frailty, a potential risk factor for aspiration, is sparse. This study aimed to assess the association between social environment and tongue pressure, as an important measure of oral function. The study focused on family structure, social networks both with and beyond neighbours, and participation in leisure activities. A population-based cross-sectional study. Annual health check-ups in a rural community in Japan. A total of 1982 participants, all over 40 years old. Anyone with missing data for the main outcome (n=14) was excluded. Tongue pressure was measured three times, and the maximum tongue pressure was used for analysis. A multivariable adjusted regression model was used to calculate parameter estimates (B) for tongue pressure. Having a social network involving neighbours (B=2.43, P=0.0001) and taking part in leisure activities (B=1.58, P=0.005) were independently associated with higher tongue pressure, but there was no link with social networks beyond neighbours (B=0.23, P=0.77). Sex-specific analyses showed that for men, having a partner was associated with higher tongue pressure, independent of the number of people in the household (B=2.26, P=0.01), but there was no association among women (B=-0.24, P=0.72; P-interaction=0.059). Having a social network involving neighbours and taking part in leisure activities were independently associated with higher tongue pressure. Marital status may be an important factor in higher tongue pressure in men. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

A concept of dynamic permission mechanism on android

Science.gov (United States)

Aron, Lukas; Hanacek, Petr

2016-02-01

This paper discuss the main security topic in mobile security area and this topic is protect user against the leakage of data. This work primarily contains the proposal of concept of dynamic permission mechanism for Android operating system. This mechanism deals with assignment or enforcement permissions to the application according to files that the application works with. Application has set of permissions that can use, but if the user opens confident files the application permissions should change its permission set and there should not be possible leakage of this secret data. The permissions set should be stricter according to opened confidential file or more open (without restriction) if the file is not secret file. The concept proposes the solution for protecting this data leakage. Idea covers rule that user should be avoided of change this permissions himself, but this behavior should be dynamic, automatic and independent. This proposal is mainly aimed to Android operating system, but the concept can be applied to other mobile platforms with some implementation changes.

Contrasting amino acid profiles among permissive and non-permissive hosts of Candidatus Liberibacter asiaticus, putative causal agent of Huanglongbing.

Directory of Open Access Journals (Sweden)

Mamoudou Sétamou

Full Text Available Huanglongbing is a devastating disease of citrus. In this study, a comprehensive profile of phloem sap amino acids (AA in four permissive host plants of Candidatus Liberibacter asiaticus (CLas and three non-permissive Rutaceae plants was conducted to gain a better understanding of host factors that may promote or suppress the bacterium. The AA profiles of Diaphorina citri nymphs and adults were similarly analyzed. A total of 38 unique AAs were detected in phloem sap of the various plants and D. citri samples, with phloem sap of young shoots containing more AAs and at higher concentrations than their mature counterparts. All AAs detected in phloem sap of non-permissive plants were also present in CLas -permissive hosts plus additional AAs in the latter class of plants. However, the relative composition of 18 commonly shared AAs varied between CLas -permissive hosts and non-permissive plants. Multivariate analysis with a partial least square discriminant methodology revealed a total of 12 AAs as major factors affecting CLas host status, of which seven were positively related to CLas tolerance/resistance and five positively associated with CLas susceptibility. Most of the AAs positively associated with CLas susceptibility were predominantly of the glutamate family, notably stressed-induced AAs such as arginine, GABA and proline. In contrast, AAs positively correlated with CLas tolerance/resistance were mainly of the serine family. Further analysis revealed that whereas the relative proportions of AAs positively associated with CLas susceptibility did not vary with host developmental stages, those associated with CLas tolerance/resistance increased with flush shoot maturity. Significantly, the proline-to-glycine ratio was determined to be an important discriminating factor for CLas permissivity with higher values characteristic of CLas -permissive hosts. This ratio could be exploited as a biomarker in HLB-resistance breeding programs.

The maximum and minimum values of the heat Q transmitted from metal to boiling water under atmospheric pressure

International Nuclear Information System (INIS)

Nukiyama, S.

1991-01-01

The quantity of heat transmitted from a metal surface to boiling water increases as the temperature difference ΔT is increased, but after the ΔT has reached a certain limit, quantity Q decreases with further increase in ΔT. This turning point is the maximum value of heat transmitted. The existence of this point was actually observed in the experiment. Under atmospheric pressure, ΔT corresponding to the maximum value of heat transfer for water at 100 degrees C falls between 20-40 degrees C, and Q is between 1,080,000 and 1,800,000 kcal/m 2 h (i.e. between 2,000 and 3,000 kg/m 2 h, if expressed in constant evaporation rate at 100 degrees C); this figure is larger than the maximum value of heat transfer as was previously considered. In this paper the minimum value of heat transfer was obtained, and in the Q-ΔT curve for the high temperature region, the burn-out effect is discussed

Further European initiatives and regulations concerning radiation protection: drinking water guideline, maximum permissible contamination in food products and feeding stuff; Weitere europaeische Initiativen und Regelungen im Strahlenschutz. Trinkwasserrichtlinie, maximal zulaessige Kontaminationswerte in Nahrungs- und Futtermitteln

Energy Technology Data Exchange (ETDEWEB)

Mundigl, Stefan [Europaeische Kommission, Generaldirektion Energie, Luxemburg (Luxembourg). Abt. D3 - Strahlenschutz, EUFO 4150

2013-07-01

The radiation protection community has observed intensively the development of basic safety standards concerning protection against hazards of ionizing radiation. The new core part of the European radiation protection legislation is complemented by several specialized regulations relevant for radiation protection. Besides the existing regulations in the field of emergency protection the European Commission initiated a drinking water guideline that will be published in the near future. Furthermore the European commission approved a revised regulation concerning the maximum permissible contamination limits for food products and feeding stuff in case of a future nuclear accident. Together with the new radiation protection basic standards a new complete, coherent and modernized European regulation package will be accomplished.

Seismic-safe conditions of blasting near pressure pipe-lines during power installation construction

International Nuclear Information System (INIS)

Smolij, N.I.; Nikitin, A.S.

1980-01-01

Seismic-safe conditions for performing drill-blasting operations in the vicinity of underground gas pipelines when constructing thermal- or nuclear power plants are discussed. It is shown that, for the determination of seismic-safe parameters, of drill-blasting operations, the maximum permissible level of seismic loads should be specified taking into account the mechanical properties of the pipeline.metal, structural parameters of the gas pipeline and the pressure of the medium transported. Besides, the seismic effect of the blast should be considered with regard to particular conditions of blasting and rock properties. The equations and diagrams used in the calculation are given

Analysis of the consequences of a steam explosion

International Nuclear Information System (INIS)

Hassmann, K.; Peehs, M.; Zeitner, W.; Reineke, H.

1979-01-01

Estimation of the maximum amount of melt that may possibly come into contact with water: determiantion of the maximum mechanical energy acting on the reactor pressure vessel; determination of the maximum load withstood by pressure vessels during steam explosions without macroscopic failure; elaboration of a statement on pressure vessel integrity by comparing the calculated maximum permissible load with the actual load. (orig.) [de

Verification of average daily maximum permissible concentration of styrene in the atmospheric air of settlements under the results of epidemiological studies of the children’s population

Directory of Open Access Journals (Sweden)

М.А. Zemlyanova

2015-03-01

Full Text Available We presented the materials on the verification of the average daily maximum permissible concentration of styrene in the atmospheric air of settlements performed under the results of own in-depth epidemiological studies of children’s population according to the principles of the international risk assessment practice. It was established that children in the age of 4–7 years when exposed to styrene at the level above 1.2 of threshold level value for continuous exposure develop the negative exposure effects in the form of disorders of hormonal regulation, pigmentary exchange, antioxidative activity, cytolysis, immune reactivity and cytogenetic disbalance which contribute to the increased morbidity of diseases of the central nervous system, endocrine system, respiratory organs, digestion and skin. Based on the proved cause-and-effect relationships between the biomarkers of negative effects and styrene concentration in blood it was demonstrated that the benchmark styrene concentration in blood is 0.002 mg/dm3. The justified value complies with and confirms the average daily styrene concentration in the air of settlements at the level of 0.002 mg/m3 accepted in Russia which provides the safety for the health of population (1 threshold level value for continuous exposure.

A Symbolic Approach to Permission Accounting for Concurrent Reasoning

NARCIS (Netherlands)

Huisman, Marieke; Mostowski, Wojciech

2015-01-01

Permission accounting is fundamental to modular, thread-local reasoning about concurrent programs. This paper presents a new, symbolic system for permission accounting. In existing systems, permissions are numeric value-based and refer to the current thread only. Our system is based on symbolic

MAXIMUM PRINCIPLE FOR SUBSONIC FLOW WITH VARIABLE ENTROPY

Directory of Open Access Journals (Sweden)

B. Sizykh Grigory

2017-01-01

Full Text Available Maximum principle for subsonic flow is fair for stationary irrotational subsonic gas flows. According to this prin- ciple, if the value of the velocity is not constant everywhere, then its maximum is achieved on the boundary and only on the boundary of the considered domain. This property is used when designing form of an aircraft with a maximum critical val- ue of the Mach number: it is believed that if the local Mach number is less than unit in the incoming flow and on the body surface, then the Mach number is less then unit in all points of flow. The known proof of maximum principle for subsonic flow is based on the assumption that in the whole considered area of the flow the pressure is a function of density. For the ideal and perfect gas (the role of diffusion is negligible, and the Mendeleev-Clapeyron law is fulfilled, the pressure is a function of density if entropy is constant in the entire considered area of the flow. Shows an example of a stationary sub- sonic irrotational flow, in which the entropy has different values on different stream lines, and the pressure is not a function of density. The application of the maximum principle for subsonic flow with respect to such a flow would be unreasonable. This example shows the relevance of the question about the place of the points of maximum value of the velocity, if the entropy is not a constant. To clarify the regularities of the location of these points, was performed the analysis of the com- plete Euler equations (without any simplifying assumptions in 3-D case. The new proof of the maximum principle for sub- sonic flow was proposed. This proof does not rely on the assumption that the pressure is a function of density. Thus, it is shown that the maximum principle for subsonic flow is true for stationary subsonic irrotational flows of ideal perfect gas with variable entropy.

14 CFR 399.35 - Special tariff permission.

Science.gov (United States)

2010-01-01

... PROCEEDINGS) POLICY STATEMENTS STATEMENTS OF GENERAL POLICY Policies Relating to Rates and Tariffs § 399.35 Special tariff permission. (a) Definition. As used in this section, to grant STP means to approve a... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Special tariff permission. 399.35 Section...

Normalizing the maximum permissible seal failure of the fuel cladding of VVER and the activity of the fission products in the coolant

International Nuclear Information System (INIS)

Luzanova, L.M.; Miglo, V.N.; Slavyagin, P.D.

1993-01-01

In most countries developing a nuclear power industry based on pressurized water reactors, one of the conditions for issuing a license under normal operating conditions for issuing a license stipulates that the fuel elements may not lose their hermetic seal either under normal operating conditions or during presumable disturbances of the conditions of normal use. At a conference on radiation safety the ALARA principle was taken to be fundamental, it being attempted to keep the activity of the coolant of the primary circuit, including the fission products emerging from unsealed fuel elements, to a level as low as reasonably possible. As many years of experience in the nuclear power industry have shown, nuclear power stations are in many cases operated with nonhermetic fuel elements in the core. Therefore, from the point of view of safety and economy, the best way to operate a power plant is to try to ensure maximum burnup of the fuel of the unsealed elements as they operate within the limits of safe activity of the fission products in the fuel circuits

Exploring Permission-Induced Risk in Android Applications for Malicious Application Detection

KAUST Repository

Wang, Wei

2014-10-07

Android has been a major target of malicious applications (malapps). How to detect and keep the malapps out of the app markets is an ongoing challenge. One of the central design points of Android security mechanism is permission control that restricts the access of apps to core facilities of devices. However, it imparts a significant responsibility to the app developers with regard to accurately specifying the requested permissions and to the users with regard to fully understanding the risk of granting certain combinations of permissions. Android permissions requested by an app depict the app\\'s behavioral patterns. In order to help understanding Android permissions, in this paper, we explore the permission-induced risk in Android apps on three levels in a systematic manner. First, we thoroughly analyze the risk of an individual permission and the risk of a group of collaborative permissions. We employ three feature ranking methods, namely, mutual information, correlation coefficient, and T-test to rank Android individual permissions with respect to their risk. We then use sequential forward selection as well as principal component analysis to identify risky permission subsets. Second, we evaluate the usefulness of risky permissions for malapp detection with support vector machine, decision trees, as well as random forest. Third, we in depth analyze the detection results and discuss the feasibility as well as the limitations of malapp detection based on permission requests. We evaluate our methods on a very large official app set consisting of 310 926 benign apps and 4868 real-world malapps and on a third-party app sets. The empirical results show that our malapp detectors built on risky permissions give satisfied performance (a detection rate as 94.62% with a false positive rate as 0.6%), catch the malapps\\' essential patterns on violating permission access regulations, and are universally applicable to unknown malapps (detection rate as 74.03%).

Maximum permissible concentrations of uranium in air

CERN Document Server

Adams, N

1973-01-01

The retention of uranium by bone and kidney has been re-evaluated taking account of recently published data for a man who had been occupationally exposed to natural uranium aerosols and for adults who had ingested uranium at the normal dietary levels. For life-time occupational exposure to uranium aerosols the new retention functions yield a greater retention in bone and a smaller retention in kidney than the earlier ones, which were based on acute intakes of uranium by terminal patients. Hence bone replaces kidney as the critical organ. The (MPC) sub a for uranium 238 on radiological considerations using the current (1959) ICRP lung model for the new retention functions is slightly smaller than for earlier functions but the (MPC) sub a determined by chemical toxicity remains the most restrictive.

Studies of the pressure dependence of the charge density distribution in cerium phosphide by the maximum-entropy method

CERN Document Server

Ishimatsu, N; Takata, M; Nishibori, E; Sakata, M; Hayashi, J; Shirotani, I; Shimomura, O

2002-01-01

The physical properties relating to 4f electrons in cerium phosphide, especially the temperature dependence and the isomorphous transition that occurs at around 10 GPa, were studied by means of x-ray powder diffraction and charge density distribution maps derived by the maximum-entropy method. The compressibility of CeP was exactly determined using a helium pressure medium and the anomaly that indicated the isomorphous transition was observed in the compressibility. We also discuss the anisotropic charge density distribution of Ce ions and its temperature dependence.

Rethinking Permissioned Blockchains

OpenAIRE

Vukolic, Marko

2017-01-01

Current blockchain platforms, especially the recent permissioned systems, have architectural limitations: smart contracts run sequentially, all node executes all smart contracts, consensus protocols are hard-coded, the trust model is static and not exible, and non-determinism in smart-contract execution poses serious problems. Overcoming these limitations is critical for improving both functional properties of blockchains, such as con dentiality and consistency, as well as their non-functiona...

A Method of Estimating Pressure and Intensity Distributions of Multielement Phased Array High Intensity Focused Ultrasonic Field at Full Power Using a Needle Hydrophone

International Nuclear Information System (INIS)

Yu Ying; Shen Guofeng; Bai Jingfeng; Chen Yazhu

2011-01-01

The pressure and intensity distribution of high intensity focused ultrasound (HIFU) fields at full power are critical for predicting heating patterns and ensuring safety of the therapy. With the limitations of maximum pressure at the hydrophone and damage from cavitation or thermal effects, it is hard to measure pressure and intensity directly when HIFU is at full power. HIFU-phased arrays are usually composed of large numbers of small elements and the sound power radiated from some of them at full power is measureable using a hydrophone, we grouped them based on the limitation of maximum permissible pressure at the hydrophone and the characteristics of the element arrangement in the array. Then sound field measurement of the group was carried out at full power level. Using the acoustic coherence principle, the pressure and intensity distribution of the array at full power level can be calculated from corresponding values from the groups. With this method, computer simulations and sound field measurement of a 65-element concentric distributed phased array was carried out. The simulation results demonstrate theoretically the feasibility of this method. Measurements on the 65-element phased array also verify the effectiveness of this method for estimating the pressure and intensity distribution of phased array at full power level using a needle hydrophone.

Office blood pressure or ambulatory blood pressure for the prediction of cardiovascular events.

Science.gov (United States)

Mortensen, Rikke Nørmark; Gerds, Thomas Alexander; Jeppesen, Jørgen Lykke; Torp-Pedersen, Christian

2017-11-21

To determine the added value of (i) 24-h ambulatory blood pressure relative to office blood pressure and (ii) night-time ambulatory blood pressure relative to daytime ambulatory blood pressure for 10-year person-specific absolute risks of fatal and non-fatal cardiovascular events. A total of 7927 participants were included from the International Database on Ambulatory blood pressure monitoring in relation to Cardiovascular Outcomes. We used cause-specific Cox regression to predict 10-year person-specific absolute risks of fatal and non-fatal cardiovascular events. Discrimination of 10-year outcomes was assessed by time-dependent area under the receiver operating characteristic curve (AUC). No differences in predicted risks were observed when comparing office blood pressure and ambulatory blood pressure. The median difference in 10-year risks (1st; 3rd quartile) was -0.01% (-0.3%; 0.1%) for cardiovascular mortality and -0.1% (-1.1%; 0.5%) for cardiovascular events. The difference in AUC (95% confidence interval) was 0.65% (0.22-1.08%) for cardiovascular mortality and 1.33% (0.83-1.84%) for cardiovascular events. Comparing daytime and night-time blood pressure, the median difference in 10-year risks was 0.002% (-0.1%; 0.1%) for cardiovascular mortality and -0.01% (-0.5%; 0.2%) for cardiovascular events. The difference in AUC was 0.10% (-0.08 to 0.29%) for cardiovascular mortality and 0.15% (-0.06 to 0.35%) for cardiovascular events. Ten-year predictions obtained from ambulatory blood pressure are similar to predictions from office blood pressure. Night-time blood pressure does not improve 10-year predictions obtained from daytime measurements. For an otherwise healthy population sufficient prognostic accuracy of cardiovascular risks can be achieved with office blood pressure. Published on behalf of the European Society of Cardiology. All rights reserved. © The Author 2017. For permissions, please email: journals.permissions@oup.com.

The effectiveness of combining inspiratory muscle training with manual therapy and a therapeutic exercise program on maximum inspiratory pressure in adults with asthma: a randomized clinical trial.

Science.gov (United States)

López-de-Uralde-Villanueva, Ibai; Candelas-Fernández, Pablo; de-Diego-Cano, Beatriz; Mínguez-Calzada, Orcález; Del Corral, Tamara

2018-06-01

The objective of this study was to evaluate whether the addition of manual therapy and therapeutic exercise protocol to inspiratory muscle training was more effective in improving maximum inspiratory pressure than inspiratory muscle training in isolation. This is a single-blinded, randomized controlled trial. In total, 43 patients with asthma were included in this study. The patients were allocated into one of the two groups: (1) inspiratory muscle training ( n = 21; 20-minute session) or (2) inspiratory muscle training (20-minute session) combined with a program of manual therapy (15-minute session) and therapeutic exercise (15-minute session; n = 22). All participants received 12 sessions, two days/week, for six weeks and performed the domiciliary exercises protocol. The main measures such as maximum inspiratory pressure, spirometric measures, forward head posture, and thoracic kyphosis were recorded at baseline and after the treatment. For the per-protocol analysis, between-group differences at post-intervention were observed in maximum inspiratory pressure (19.77 cmH 2 O (11.49-28.04), P < .05; F = 22.436; P < .001; η 2 p  = 0.371) and forward head posture (-1.25 cm (-2.32 to -0.19), P < .05; F = 5.662; P = .022; η 2 p  = 0.13). The intention-to-treat analysis showed the same pattern of findings. The inspiratory muscle training combined with a manual therapy and therapeutic exercise program is more effective than its application in isolation for producing short-term maximum inspiratory pressure and forward head posture improvements in patients with asthma.

Permissive weight bearing in trauma patients with fracture of the lower extremities: prospective multicenter comparative cohort study.

Science.gov (United States)

Kalmet, Pishtiwan H S; Meys, Guido; V Horn, Yvette Y; Evers, Silvia M A A; Seelen, Henk A M; Hustinx, Paul; Janzing, Heinrich; Vd Veen, Alexander; Jaspars, Coen; Sintenie, Jan Bernard; Blokhuis, Taco J; Poeze, Martijn; Brink, Peter R G

2018-02-02

The standard aftercare treatment in surgically treated trauma patients with fractures around or in a joint, known as (peri)- or intra-articular fractures of the lower extremities, is either non-weight bearing or partial weight bearing. We have developed an early permissive weight bearing post-surgery rehabilitation protocol in surgically treated patients with fractures of the lower extremities. In this proposal we want to compare our early permissive weight bearing protocol to the existing current non-weight bearing guidelines in a prospective comparative cohort study. The study is a prospective multicenter comparative cohort study in which two rehabilitation aftercare treatments will be contrasted, i.e. permissive weight bearing and non-weight bearing according to the AO-guideline. The study population consists of patients with a surgically treated fracture of the pelvis/acetabulum or a surgically treated (peri)- or intra-articular fracture of the lower extremities. The inclusion period is 12 months. The duration of follow up is 6 months, with measurements taken at baseline, 2,6,12 and 26 weeks post-surgery. ADL with Lower Extremity Functional Scale. Outcome variables for compliance, as measured with an insole pressure measurement system, encompass peak load and step duration. This study will investigate the (cost-) effectiveness of a permissive weight bearing aftercare protocol. The results will provide evidence whether a permissive weight bearing protocol is more effective than the current non-weight bearing protocol. The study is registered in the Dutch Trial Register ( NTR6077 ). Date of registration: 01-09-2016.

42 CFR 433.66 - Permissible provider-related donations.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Permissible provider-related donations. 433.66... Requirements State Financial Participation § 433.66 Permissible provider-related donations. (a) General rule... provider-related donations without a reduction in FFP, only in accordance with the requirements of this...

Can ‘Mobile Platform’ and ‘Permission Marketing’ dance a tango to the consumers' tune? Modeling adoption of ‘SMS based Permission Advertising’

OpenAIRE

Prerna Bamoriya

2015-01-01

Many a times situation of advertising clutter is further aggrieved by the markers’ intrusive practices i.e. not asking for consumer’s explicit permission. It results in consumers’ alienation and reduced advertising effectiveness. Solution could be integration of Permission Marketing with an innovative advertising platform like Mobile. This study aimed to develop and validate a comprehensive model for understanding consumers’ adoption behavior towards SMS Based Permission Advertising (SBPA). F...

Quantitative Security Risk Assessment of Android Permissions and Applications

OpenAIRE

Wang , Yang; Zheng , Jun; Sun , Chen; Mukkamala , Srinivas

2013-01-01

Part 6: Mobile Computing; International audience; The booming of the Android platform in recent years has attracted the attention of malware developers. However, the permissions-based model used in Android system to prevent the spread of malware, has shown to be ineffective. In this paper, we propose DroidRisk, a framework for quantitative security risk assessment of both Android permissions and applications (apps) based on permission request patterns from benign apps and malware, which aims ...

Effect of error in crack length measurement on maximum load fracture toughness of Zr-2.5Nb pressure tube material

International Nuclear Information System (INIS)

Bind, A.K.; Sunil, Saurav; Singh, R.N.; Chakravartty, J.K.

2016-03-01

Recently it was found that maximum load toughness (J max ) for Zr-2.5Nb pressure tube material was practically unaffected by error in Δ a . To check the sensitivity of the J max to error in Δ a measurement, the J max was calculated assuming no crack growth up to the maximum load (P max ) for as received and hydrogen charged Zr-2.5Nb pressure tube material. For load up to the P max , the J values calculated assuming no crack growth (J NC ) were slightly higher than that calculated based on Δ a measured using DCPD technique (JDCPD). In general, error in the J calculation found to be increased exponentially with Δ a . The error in J max calculation was increased with an increase in Δ a and a decrease in J max . Based on deformation theory of J, an analytic criterion was developed to check the insensitivity of the J max to error in Δ a . There was very good linear relation was found between the J max calculated based on Δ a measured using DCPD technique and the J max calculated assuming no crack growth. This relation will be very useful to calculate J max without measuring the crack growth during fracture test especially for irradiated material. (author)

Maximum respiratory pressure measuring system : calibration and evaluation of uncertainty

NARCIS (Netherlands)

Ferreira, J.L.; Pereira, N.C.; Oliveira Júnior, M.; Vasconcelos, F.H.; Parreira, V.F.; Tierra-Criollo, C.J.

2010-01-01

The objective of this paper is to present a methodology for the evaluation of uncertainties in the measurements results obtained during the calibration of a digital manovacuometer prototype (DM) with a load cell sensor pressure device incorporated. Calibration curves were obtained for both pressure

Model for Calculating the Maximum Permissible Tax Burden in Amur Region in the Context of the Implementation of Largest Investment Projects

Directory of Open Access Journals (Sweden)

Viktor Vladimirovich Ivanov

2018-03-01

Full Text Available According to the Government of the Amur region, tax collection from the implementation of investment projects was tightly controlled from 2016, because of the region’s high debt load. This situation requires assessing the acceptability of the level of regional tax burden for business entities. The purpose of this paper is to develop a model for assessing the level of regional tax burden, taking into account the implementation of the largest investment projects in the territory. The main hypothesis of this paper consists, firstly, in the existence of tax burden, which is acceptable for regional economic entities. Secondly, this level of tax burden ensures the growth of fiscal revenues for the budget. We proposed to assess the level of tax burden on the basis of a three-factor linear heterogeneous production function, taking into account certain economic indicators of the largest investment project — “Construction of the Vostochny Сosmodrome”. The concept of the Laffer curve serves as a research methodology. According to our calculations, since 2011, the tax burden in the Amur region has a clear tendency to increase. At the same time, from 2007 to the present time, the tax burden exceeds its maximum permissible value and constrains economic growth in the region. If this trend continues, by 2018 tax revenues from the territory of the region will be on the verge of reduction. The obtained results show that the tax burden in the Amur region in 2017 is 16.81 %. To stimulate the activities of economic entities in the region, and as a consequence, to increase the GRP of the region, it is necessary to reduce the level of taxation by 4.77 percentage points (to 12.04 %, Thus, the current economic situation requires to change the course of regional taxation policy to a more liberal attitude towards taxpayers. Otherwise, soon the budget of the Amur region may fail to receive a part of revenues, as the region’s economic entities will not be able to

Android Permission Model

OpenAIRE

Birendra, Chalise

2016-01-01

The recent evolution on the smart phone technology has made its application market huge and less secure. Every single day large number of apps introduced in the android market (mostly on google play store) without any particular inspections which creates a lot of security issues and they remain unresolved. There are a lot of recent and increasing security issues which are mostly caused by the android apps. Mainly, the access of user data through the apps relied on the users given permission t...

Comprehensive performance analyses and optimization of the irreversible thermodynamic cycle engines (TCE) under maximum power (MP) and maximum power density (MPD) conditions

International Nuclear Information System (INIS)

Gonca, Guven; Sahin, Bahri; Ust, Yasin; Parlak, Adnan

2015-01-01

This paper presents comprehensive performance analyses and comparisons for air-standard irreversible thermodynamic cycle engines (TCE) based on the power output, power density, thermal efficiency, maximum dimensionless power output (MP), maximum dimensionless power density (MPD) and maximum thermal efficiency (MEF) criteria. Internal irreversibility of the cycles occurred during the irreversible-adiabatic processes is considered by using isentropic efficiencies of compression and expansion processes. The performances of the cycles are obtained by using engine design parameters such as isentropic temperature ratio of the compression process, pressure ratio, stroke ratio, cut-off ratio, Miller cycle ratio, exhaust temperature ratio, cycle temperature ratio and cycle pressure ratio. The effects of engine design parameters on the maximum and optimal performances are investigated. - Highlights: • Performance analyses are conducted for irreversible thermodynamic cycle engines. • Comprehensive computations are performed. • Maximum and optimum performances of the engines are shown. • The effects of design parameters on performance and power density are examined. • The results obtained may be guidelines to the engine designers

Effects of bruxism on the maximum bite force

Directory of Open Access Journals (Sweden)

Todić Jelena T.

2017-01-01

Full Text Available Background/Aim. Bruxism is a parafunctional activity of the masticatory system, which is characterized by clenching or grinding of teeth. The purpose of this study was to determine whether the presence of bruxism has impact on maximum bite force, with particular reference to the potential impact of gender on bite force values. Methods. This study included two groups of subjects: without and with bruxism. The presence of bruxism in the subjects was registered using a specific clinical questionnaire on bruxism and physical examination. The subjects from both groups were submitted to the procedure of measuring the maximum bite pressure and occlusal contact area using a single-sheet pressure-sensitive films (Fuji Prescale MS and HS Film. Maximal bite force was obtained by multiplying maximal bite pressure and occlusal contact area values. Results. The average values of maximal bite force were significantly higher in the subjects with bruxism compared to those without bruxism (p 0.01. Maximal bite force was significantly higher in the males compared to the females in all segments of the research. Conclusion. The presence of bruxism influences the increase in the maximum bite force as shown in this study. Gender is a significant determinant of bite force. Registration of maximum bite force can be used in diagnosing and analysing pathophysiological events during bruxism.

Control over Permissible Short Emergency Overloads in Power Transformers

Directory of Open Access Journals (Sweden)

V. A. Anischenko

2010-01-01

Full Text Available The paper proposes a method for determination a permissible duration of short intermittent overloads of power transformers that permits to avoid non-permissible over-heating of winding insulation and fully utilize overloading transformer ability.

46 CFR 197.462 - Pressure vessels and pressure piping.

Science.gov (United States)

2010-10-01

... that each pressure vessel, including each volume tank, cylinder and PVHO, and each pressure piping... tests conducted in accordance with this section shall be either hydrostatic tests or pneumatic tests. (1... times the maximum allowable working pressure. (2) When a pneumatic test is conducted on a pressure...

Is the publication of exit poll results morally permissible?

DEFF Research Database (Denmark)

Sønderholm, Jørn

2016-01-01

This article is about exit polls. It addresses the question of whether or not it is morally permissible to publish exit poll results. The conclusion of the article is that an affirmative answer should be given to this question. In section 2, the master argument in favor of the moral permissibility...... of the publication of exit poll results is introduced. This is a strong argument. It is, however, argued that it might be the case that the conclusion of this argument should be rejected if there are other, and weightier, arguments against the idea that the publication of exit poll results is morally permissible....... In section 3, the strongest arguments against the moral permissibility of the publication of exit poll results are outlined and discussed. The conclusion of this section is that all these arguments fail in their intended purpose. The conclusion of the article is therefore justified....

Experimental study, in rat wistar, of cadmium distribution and elimination as a function of administration route. Cadmium 109 maximum permissible concentration

International Nuclear Information System (INIS)

Valero, Marc.

1979-01-01

The absorption and the elimination of cadmium have been investigated in rats wistar after oral administration or after inhalation. Before studying gastro-intestinal absorption, it appeared necessary to precise acute toxicity of orally administred cadmium. The distribution of cadmium within organes was determined following a single or multiple oral doses, and we specially studied retention of a Cd dose ingested after several weeks of treatment with Cd-Acetate. Pulmonary and gastro-intestinal absorption of cadmium after ihalation of Cd-microparticles were studied. Data obtained from these studies on rats and extrapolated to man were used to calculate mximum permissible concentration (M.P.C.) of Cd-109 in water and in air [fr

Criteria of assessment for local wall thickness reductions in operative high-pressure gas pipelines; Beurteilungskriterien fuer lokale Wanddickenminderungen an in Betrieb befindlichen Gashochdruckleitungen

Energy Technology Data Exchange (ETDEWEB)

Hass, Georg [NetzDienste Rhein/Main GmbH, Frankfurt am Main (Germany); Hoffman, Ulrich [VNG - Verbundnetz Gas AG, Leipzig (Germany); Konarske, Juergen [RWE Westfalen-Weser-Ems Netzservice GmbH, Recklinghausen (Germany); Soppa, Thorsten [NG Netz Gas+Wasser (Germany). Bau/Betrieb Hochdrucknetz; Steiner, Michael [Open Grid Europe GmbH, Essen (Germany). Integritaet/Werkstofftechnik

2011-07-01

TUeV Nord, Salzgitter Mannesmann Forschung and DVGW investigated methods to assess local wall thickness reductions in operative high-pressure gas pipelines. Methods described in the relevant literature were reviewed with regard to the limiting criteria defined for maximum permissible wall thickness reductions. On the basis of this literature study and additional calculations, a comparative evaluation of the available methods was made. Several methods were identified that are compatible with the existing safety concept and general availability. It was found that - nearly independent of the method - burst safeties of 1.8 to 2.0 were used. The ultimate goal is the development of a German standard evaluation concept for local wall thickness reductions in high-pressure gas pipelines in order to avoid uncertainties and/or misinterpretations.

45 CFR 1639.4 - Permissible representation of eligible clients.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 4 2010-10-01 2010-10-01 false Permissible representation of eligible clients... CORPORATION WELFARE REFORM § 1639.4 Permissible representation of eligible clients. Recipients may represent an individual eligible client who is seeking specific relief from a welfare agency. [62 FR 30766...

Method of operating a reactor

International Nuclear Information System (INIS)

Oosumi, Katsumi; Yamamoto, Michiyoshi.

1980-01-01

Purpose: To prevent stress corrosion cracking in the structural material of a reactor pressure vessel. Method: Prior to the starting of a reactor, the reactor pressure vessel is evacuated to carry out degassing of reactor water, and, at the same time, reactor water is heated. After reactor water is heated to a predetermined temperature, control rods are extracted to start nuclear heating. While the temperature of the reactor water is in a temperature range where elution of a metal which is a structural material of the reactor pressure vessel becomes vigorous and the sensitivity to the stress corrosion cracks increases, the reactor is operated at the maximum permissible temperature raising speed or maximum permissible cooling speed. (Aizawa, K.)

46 CFR 176.700 - Permission for repairs and alterations.

Science.gov (United States)

2010-10-01

... repair or replacement, other than replacement in kind, of electrical wiring, fuel lines, tanks, boilers... 46 Shipping 7 2010-10-01 2010-10-01 false Permission for repairs and alterations. 176.700 Section... (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Repairs and Alterations § 176.700 Permission for...

User-centric android flexible permissions

NARCIS (Netherlands)

Scoccia, Gian Luca; Malavolta, Ivano; Autili, Marco; Di Salle, Amleto; Inverardi, Paola

2017-01-01

Privacy in mobile apps is a fundamental aspect to be considered, particularly with regard to meeting end user expectations. Due to the rigidities of the Android permission model, desirable trade-offs are not allowed. End users are confined into a secondary role, having the only option of choosing

Evaluation of the external radiation exposure dosimetry and calculation of maximum permissible concentration values for airborne materials containing 18F, 15O, 13N, 11C and 133Xe

International Nuclear Information System (INIS)

Piltingsrud, H.V.; Gels, G.L.

1985-01-01

To better understand the dose equivalent (D.E.) rates produced by airborne releases of gaseous positron-emitting radionuclides under various conditions of cloud size, a study of the external radiation exposure dosimetry of these radionuclides, as well as negatron, gamma and x-ray emitting 133Xe, was undertaken. This included a calculation of the contributions to D.E. as a function of cloud radii, at tissue depths of 0.07 mm (skin), 3 mm (lens of eye) and 10 mm (whole body) from both the particulate and photon radiations emitted by these radionuclides. Estimates of maximum permissible concentration (MPC) values were also calculated based on the calculated D.E. rates and current regulations for personnel radiation protection (CFR84). Three continuous air monitors, designed for use with 133Xe, were evaluated for applications in monitoring air concentrations of the selected positron emitters. The results indicate that for a given radionuclide and for a cloud greater than a certain radius, personnel radiation dosimeters must respond acceptably to only the photon radiations emitted by the radionuclide to provide acceptable personnel dosimetry. For clouds under that radius, personnel radiation dosimeters must also respond acceptably to the positron or negatron radiations to provide acceptable personnel dosimetry. It was found that two out of the three air concentration monitors may be useful for monitoring air concentrations of the selected positron emitters

On the substantion of permissible concentrations of plutonium isotopes in the water of fresh water and sea water NPP cooling reservoirs

International Nuclear Information System (INIS)

Grachev, M.I.; Gusev, D.I.; Stepanova, V.D.

1985-01-01

Substantiation of maximum permissible concentration (PC) of plutonium isotopes ( 238 Pu, 239 Pu, 240 Pu) in fresh and sea water cooling reservoirs of NPP with fast neutron reactors is given. The main criterion when calculating permissible plutonium content in water of surface reservoirs is the requirement not to exceed the established limits for radiation doses to persons resulted from water use. Data on coefficients of plutonium concentration in sea and fresh water hydrobionts are presented as well as on plutonium PC in water of fresh and sea water cooling reservoirs and bottom sediments of sea water cooling reservoirs. It is shown that doses to critical groups of population doesn't exceed potentially hazardous levels due to plutonium intake through food chains. But the calculation being carried out further should be corrected

Determination of Secondary Encasement Pipe Design Pressure

Energy Technology Data Exchange (ETDEWEB)

TEDESCHI, A.R.

2000-10-26

This document published results of iterative calculations for maximum tank farm transfer secondary pipe (encasement) pressure upon failure of the primary pipe. The maximum pressure was calculated from a primary pipe guillotine break. Results show encasement pipeline design or testing pressures can be significantly lower than primary pipe pressure criteria.

Development of a dynamic operation permission system to support operations in an anomalous situation of PWR plants

International Nuclear Information System (INIS)

Gofuku, Akio; Nishio, Takuya; Ohi, Tadashi; Ito, Koji

2005-01-01

This paper describes a proto-type dynamic operation permission system to avoid commission errors of operators. The system lies between CRT-based operation panels and plant control systems and checks an operation by operators if it follows typical operation procedure described in operation manuals and it has suitable effects on plant condition. The applicability of the proto-type system is demonstrated through the application to the recovery operations of a steam generator tube rupture accident of a three-loop pressurized water reactor plant

The Maximum Flux of Star-Forming Galaxies

Science.gov (United States)

Crocker, Roland M.; Krumholz, Mark R.; Thompson, Todd A.; Clutterbuck, Julie

2018-04-01

The importance of radiation pressure feedback in galaxy formation has been extensively debated over the last decade. The regime of greatest uncertainty is in the most actively star-forming galaxies, where large dust columns can potentially produce a dust-reprocessed infrared radiation field with enough pressure to drive turbulence or eject material. Here we derive the conditions under which a self-gravitating, mixed gas-star disc can remain hydrostatic despite trapped radiation pressure. Consistently taking into account the self-gravity of the medium, the star- and dust-to-gas ratios, and the effects of turbulent motions not driven by radiation, we show that galaxies can achieve a maximum Eddington-limited star formation rate per unit area \\dot{Σ }_*,crit ˜ 10^3 M_{⊙} pc-2 Myr-1, corresponding to a critical flux of F*, crit ˜ 1013L⊙ kpc-2 similar to previous estimates; higher fluxes eject mass in bulk, halting further star formation. Conversely, we show that in galaxies below this limit, our one-dimensional models imply simple vertical hydrostatic equilibrium and that radiation pressure is ineffective at driving turbulence or ejecting matter. Because the vast majority of star-forming galaxies lie below the maximum limit for typical dust-to-gas ratios, we conclude that infrared radiation pressure is likely unimportant for all but the most extreme systems on galaxy-wide scales. Thus, while radiation pressure does not explain the Kennicutt-Schmidt relation, it does impose an upper truncation on it. Our predicted truncation is in good agreement with the highest observed gas and star formation rate surface densities found both locally and at high redshift.

The ecological determination of the permissible concentrations for radioactive contamination

International Nuclear Information System (INIS)

Kononovich, A.L.

1996-01-01

It is supposed that all inhabitants of the ecosystem are enjoying equal rights. The report describes the approximate method of ecology normalizing of the permissible radionuclide concentrations. Definition of the permissible concentration is made by an indirect way, since the defining criterion is unknown

Can ‘Mobile Platform’ and ‘Permission Marketing’ dance a tango to the consumers' tune? Modeling adoption of ‘SMS based Permission Advertising’

Directory of Open Access Journals (Sweden)

Prerna Bamoriya

2015-12-01

Full Text Available Many a times situation of advertising clutter is further aggrieved by the markers’ intrusive practices i.e. not asking for consumer’s explicit permission. It results in consumers’ alienation and reduced advertising effectiveness. Solution could be integration of Permission Marketing with an innovative advertising platform like Mobile. This study aimed to develop and validate a comprehensive model for understanding consumers’ adoption behavior towards SMS Based Permission Advertising (SBPA. For this, data was collected using systematic random sampling from 524 respondents and was analyzed using Structural Equation Modeling. Study revealed some critical variables along with complex relationships among such variables, in form of an empirically validated model. At last, study made some important implications for practitioners and researchers.

Nurses' attitudes towards pressure ulcer prevention in Turkey.

Science.gov (United States)

Aslan, Arzu; Yavuz van Giersbergen, Meryem

2016-02-01

Pressure ulcers remain a major problem in healthcare system. Pressure ulcer incidence is widely accepted as an indicator for the quality of care. Positive attitudes towards pressure ulcer prevention have positive impacts on preventive care. The aim of this study was to identify nurses' attitude towards pressure ulcer prevention. The study design was descriptive. The study was carried out in a university hospital in Izmir, Turkey. The study population consisted of 660 nurses who work in medical and surgical clinics and intensive care units. The study sample consisted of 426 nurses who agreed to participate. Attitude towards Pressure Ulcer Prevention Instrument was used in order to evaluate nurses' attitudes. Written permissions for ethical considerations and Attitude towards Pressure Ulcer Prevention Instrument permission were obtained. Data were collected between June and July 2014. The statistics program SPSS 18 packaged software was used in the analyses of data. The average age of the nurses who took part in the study was 31.86 ± 7.09 years and the average work experience was 8.88 ± 7.41 years; 36.9% (n: 157) were working in intensive care units. The nurses' average score on the Attitude towards Pressure Ulcer Prevention Instrument was 43.74 ± 4.29 (84.12%). It was seen that the attitudes of the nurses towards the prevention of pressure ulcers was positive. To read guidelines and training time about pressure ulcer prevention affect positively attitudes towards the prevention of pressure ulcers. Copyright © 2015 Tissue Viability Society. Published by Elsevier Ltd. All rights reserved.

The link between maternal sleep and permissive parenting during late adolescence.

Science.gov (United States)

Tu, Kelly M; Elmore-Staton, Lori; Buckhalt, Joseph A; El-Sheikh, Mona

2018-03-05

Utilizing a multi-method design, the present study examined the association between maternal sleep, assessed via actigraphy and self-reports, and permissive parenting (e.g. lax, inconsistent discipline) during adolescence, as well as the extent to which this association differed by mothers' race/ethnicity and socioeconomic status. The sample was comprised of 234 mothers (M age = 41.76 years, SD = 6.25; 67% European-American, 31% African-American, 2% other race/ethnicities) and 237 adolescents (113 boys, 124 girls; M age = 15.80 years, SD = 0.80; 66% European-American, 34% African-American). Mothers' sleep duration (actual sleep minutes) and quality (sleep efficiency, latency, long wake episodes) were assessed using actigraphy. Mothers also reported on their sleep problems and adolescents reported on mothers' permissive parenting behaviours. Results revealed that actigraphy-based longer sleep duration and shorter sleep latency were associated with lower levels of permissive parenting. Further, mothers' race/ethnicity and socioeconomic status moderated the association between actigraphy-based sleep quality (i.e. sleep efficiency, long wake episodes) and permissive parenting. Specifically, a negative association between sleep efficiency and permissive parenting was evident only for African-American mothers. In addition, a positive association between more frequent night wakings and permissive parenting was evident only for mothers from lower socioeconomic status households. The findings highlight the benefits of longer and higher-quality sleep for reducing the risk of permissive parenting, especially among ethnic minority mothers and mothers from lower socioeconomic status households. © 2018 European Sleep Research Society.

May I sleep in your bed? Getting permission to book

NARCIS (Netherlands)

Karlsson, L.; Kemperman, A.D.A.M.; Dolnicar, S.

2017-01-01

Demand for tourist accommodation offered on peer-to-peer networks is skyrocketing. In such networks tourists can only book if the accommodation provider (host) gives their permission. Needing permission to book accommodation is radically new in tourism. No hotel, motel or B&B assesses a tourist

Rationalizing the Permissibility of Mosque Decoration

Directory of Open Access Journals (Sweden)

Spahic Omer

2016-06-01

Full Text Available This paper discusses the subject of mosque decoration and some of the criteria which determine its permissibility or otherwise. Some aspects of the matter are somewhat sensitive and double-edged. Thus, the paper presents an objective, balanced and scientific account of the theme, steering clear of the sentimental aspects of the evidences often put forth by both the proponents and opponents of mosque decoration. The main thrusts of the paper are the issues pertaining to the legitimacy of decoration in general, the subject of the function of mosques vis-à-vis their decoration, as well as the broad guidelines that regulate mosque decoration emphasizing the decoration of the mihrab (praying niche area and the qiblah wall. The paper concludes that in principle mosque decoration is permissible so long as it conforms to the requirements of the Islamic spirituality and the quintessence of genuine Islamic art and architecture.

Burst pressure investigation of filament wound type IV composite pressure vessel

Science.gov (United States)

Farhood, Naseer H.; Karuppanan, Saravanan; Ya, H. H.; Baharom, Mohamad Ariff

2017-12-01

Currently, composite pressure vessels (PVs) are employed in many industries such as aerospace, transportations, medical etc. Basically, the use of PVs in automotive application as a compressed natural gas (CNG) storage cylinder has been growing rapidly. Burst failure due to the laminate failure is the most critical failure mechanism for composite pressure vessels. It is predominantly caused by excessive internal pressure due to an overfilling or an overheating. In order to reduce fabrication difficulties and increase the structural efficiency, researches and studies are conducted continuously towards the proper selection of vessel design parameters. Hence, this paper is focused on the prediction of first ply failure pressure for such vessels utilizing finite element simulation based on Tsai-Wu and maximum stress failure criterions. The effects of laminate stacking sequence and orientation angle on the burst pressure were investigated in this work for a constant layered thickness PV. Two types of winding design, A [90°2/∓θ16/90°2] and B [90°2/∓θ]ns with different orientations of helical winding reinforcement were analyzed for carbon/epoxy composite material. It was found that laminate A sustained a maximum burst pressure of 55 MPa for a sequence of [90°2/∓15°16/90°2] while the laminate B returned a maximum burst pressure of 45 MPa corresponding to a stacking sequence of [90°2/±15°/90°2/±15°/90°2/±15° ....] up to 20 layers for a constant vessel thickness. For verification, a comparison was done with the literature under similar conditions of analysis and good agreement was achieved with a maximum difference of 4% and 10% for symmetrical and unsymmetrical layout, respectively.

Substantiation of the permissible radioactive contamination of working clothes

International Nuclear Information System (INIS)

Shcherbakov, V.L.; Korostin, A.S.

1977-01-01

A permissible level of working clothes contamination was determined on the base of the main migration routes of radioactive contaminants: permeation directly through the clothes into subclothes space on skin surface, emission into the air with amount of contaminants subsequently got by the organism of a working person through inhalation as well as transfer in the process of contacting of contaminated working clothes and surfaces of premises equipment, working person hands with amount of contaminants posteriorly got by the organism by alimentary or inhalation ways. Using the experimental and literature data available the permissible levels of working clothes contamination for the mentioned migration routes of radioactive materials have been calculated. According to the data obtained the permissible levels of working clothes contamination must not exceed 4 alpha-part/(cm 2 xmin) for contamination with high-tonic isotopes, 20 alpha-part./(cm 2 xmin) with other alpha-detine isotopes, 1000 beta-part./(cm 2 xmin) with beta-active ones. The permissible level of contamination of additional materials of the individual protection in the case of their contamination with high-tonic alpha-actine isotopes must not exceed 50 alpha-part./(cm 2 xmin), 200 alpha-part./(cm 2 xmin) for contamination th other alpha-active isotopes and 400 beta-part./(cm 2 xmin) with beta-active isotopes

Susceptibility to social pressure following ventromedial prefrontal cortex damage.

Science.gov (United States)

Chen, Kuan-Hua; Rusch, Michelle L; Dawson, Jeffrey D; Rizzo, Matthew; Anderson, Steven W

2015-11-01

Social pressure influences human behavior including risk taking, but the psychological and neural underpinnings of this process are not well understood. We used the human lesion method to probe the role of ventromedial prefrontal cortex (vmPFC) in resisting adverse social pressure in the presence of risk. Thirty-seven participants (11 with vmPFC damage, 12 with brain damage outside the vmPFC and 14 without brain damage) were tested in driving simulator scenarios requiring left-turn decisions across oncoming traffic with varying time gaps between the oncoming vehicles. Social pressure was applied by a virtual driver who honked aggressively from behind. Participants with vmPFC damage were more likely to select smaller and potentially unsafe gaps under social pressure, while gap selection by the comparison groups did not change under social pressure. Participants with vmPFC damage also showed prolonged elevated skin conductance responses (SCR) under social pressure. Comparison groups showed similar initial elevated SCR, which then declined prior to making left-turn decisions. The findings suggest that the vmPFC plays an important role in resisting explicit and immediately present social pressure with potentially negative consequences. The vmPFC appears to contribute to the regulation of emotional responses and the modulation of decision making to optimize long-term outcomes. © The Author (2015). Published by Oxford University Press. For Permissions, please email: journals.permissions@oup.com.

Permissive Subsorted Partial Logic in CASL

DEFF Research Database (Denmark)

Cerioli, Maura; Haxthausen, Anne Elisabeth; Krieg-Brückner, Bernd

1997-01-01

This paper presents a permissive subsorted partial logic used in the CoFI Algebraic Specification Language. In contrast to other order-sorted logics, subsorting is not modeled by set inclusions, but by injective embeddings allowing for more general models in which subtypes can have different data...

Permissive hypercapnia and risk for brain injury and developmental impairment.

Science.gov (United States)

Hagen, Erika W; Sadek-Badawi, Mona; Carlton, David P; Palta, Mari

2008-09-01

Permissive hypercapnia is a respiratory-care strategy that is used to reduce the risk for lung injury. The goal of this study was to evaluate whether permissive hypercapnia is associated with higher risk for intraventricular hemorrhage and early childhood behavioral and functional problems than normocapnia among very low birth weight infants. Very low birth weight infants from a statewide cohort were eligible for this study when they were born at <32 weeks' gestational age and survived at least 24 hours. Infants were classified as receiving a permissive hypercapnia, normocapnia, or unclassifiable respiratory strategy during the first 24 hours after birth according to an algorithm based on Pco(2) values and respiratory-treatment decisions that were abstracted from medical charts. Intraventricular hemorrhage diagnosis was also abstracted from the medical chart. Behavioral and functional outcomes were assessed by parent interview at 2 to 3 years. Logistic regression was used to evaluate the relationship between intraventricular hemorrhage and respiratory strategy; ordinary linear regression was used to evaluate differences in behavior and function scores between children by respiratory strategy. Infants who received a permissive hypercapnia strategy were not more likely to have intraventricular hemorrhage than those with normocapnia. There were no differences in any of the behavioral or functional scores among children according to respiratory strategy. There was a significant interaction between care strategy and 1-minute Apgar score, indicating that infants with lower Apgar scores may be at higher risk for intraventricular hemorrhage with permissive hypercapnia. This study suggests that permissive hypercapnia does not increase risk for brain injury and impairment among very low birth weight children. The interaction between respiratory strategy and Apgar score is a potential worrisome exception to this conclusion. Future research should further evaluate the effect

Child Abuse, Resting Blood Pressure, and Blood Pressure Reactivity to Psychosocial Stress.

Science.gov (United States)

Gooding, Holly C; Milliren, Carly E; Austin, S Bryn; Sheridan, Margaret A; McLaughlin, Katie A

2016-01-01

Childhood trauma is associated with hypertension in adults. It is unknown whether childhood trauma predicts elevated blood pressure earlier in development. We investigated whether the trauma of child abuse was associated with blood pressure in adolescents. The sample included 145 adolescents aged 13-17 years, 40% with exposure to child abuse. The mean age of participants was 14.93 years (SD = 1.33); 58% were female. The majority self-identified as non-Hispanic White (43%), with the remainder identifying as non-Hispanic Black (17%), Hispanic (17%), or other/mixed race (23%). We used established age/sex/height-specific cutoffs to determine the prevalence of prehypertension and hypertension in the sample. We used two-sample t tests to examine associations of abuse with resting systolic blood pressure (SBP) and diastolic blood pressure (DBP) and blood pressure reactivity to the Trier Social Stress Test and a frustration task. We used linear regression to adjust for potential confounders including sociodemographic variables, body mass index, smoking, and psychopathology. Mean resting SBP and DBP were 114.07 mmHg and 61.35 mmHg in those with a history of abuse and 111.39 mmHg and 56.89 mmHg in those without a history of abuse. This difference was significant for DBP only. Twelve percent of participants met criteria for prehypertension or hypertension based on resting blood pressure values; this did not differ between those with and without an abuse history. Child abuse was associated with lower DBP and SBP reactivity to laboratory stress tasks and reduced DBP reactivity to frustration. These associations were robust to adjustment for potential confounders. Child abuse is associated with higher resting DBP and blunted DBP and SBP reactivity to laboratory stress in adolescence. These findings suggest a potential pathway by which child abuse leads to hypertension. © The Author 2015. Published by Oxford University Press on behalf of the Society of Pediatric Psychology. All

Blood pressure normalization post-jugular venous balloon angioplasty.

Science.gov (United States)

Sternberg, Zohara; Grewal, Prabhjot; Cen, Steven; DeBarge-Igoe, Frances; Yu, Jinhee; Arata, Michael

2015-05-01

association between blood pressure deviation and internal jugular veins narrowing, and whether blood pressure normalization affects Patient's clinical outcomes. © The Author(s) 2013 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Maximum Water Hammer Sensitivity Analysis

OpenAIRE

Jalil Emadi; Abbas Solemani

2011-01-01

Pressure waves and Water Hammer occur in a pumping system when valves are closed or opened suddenly or in the case of sudden failure of pumps. Determination of maximum water hammer is considered one of the most important technical and economical items of which engineers and designers of pumping stations and conveyance pipelines should take care. Hammer Software is a recent application used to simulate water hammer. The present study focuses on determining significance of ...

Determination Of Maximum Power Of The RSG-Gas At Power Operation Mode Using One Line Cooling System

International Nuclear Information System (INIS)

Hastuti, Endiah Puji; Kuntoro, Iman; Darwis Isnaini, M.

2000-01-01

In the frame of minimizing the operation-cost, operation mode using one line cooling system is being evaluated. Maximum reactor power shall be determined to assure that the existing safety criteria are not violated. The analysis was done by means of a core thermal hydraulic code, COOLOD-N. The code solves core thermal hydraulic equation at steady state conditions. By varying the reactor power as the input, thermal hydraulic parameters such as fuel cladding and fuel meat temperatures as well as safety margin against flow instability were calculated. Imposing the safety criteria to the results, maximum permissible power for this operation was obtained as much as 17.1 MW. Nevertheless, for operation the maximum power is limited to 15MW

Maximum production rate optimization for sulphuric acid decomposition process in tubular plug-flow reactor

International Nuclear Information System (INIS)

Wang, Chao; Chen, Lingen; Xia, Shaojun; Sun, Fengrui

2016-01-01

A sulphuric acid decomposition process in a tubular plug-flow reactor with fixed inlet flow rate and completely controllable exterior wall temperature profile and reactants pressure profile is studied in this paper by using finite-time thermodynamics. The maximum production rate of the aimed product SO 2 and the optimal exterior wall temperature profile and reactants pressure profile are obtained by using nonlinear programming method. Then the optimal reactor with the maximum production rate is compared with the reference reactor with linear exterior wall temperature profile and the optimal reactor with minimum entropy generation rate. The result shows that the production rate of SO 2 of optimal reactor with the maximum production rate has an increase of more than 7%. The optimization of temperature profile has little influence on the production rate while the optimization of reactants pressure profile can significantly increase the production rate. The results obtained may provide some guidelines for the design of real tubular reactors. - Highlights: • Sulphuric acid decomposition process in tubular plug-flow reactor is studied. • Fixed inlet flow rate and controllable temperature and pressure profiles are set. • Maximum production rate of aimed product SO 2 is obtained. • Corresponding optimal temperature and pressure profiles are derived. • Production rate of SO 2 of optimal reactor increases by 7%.

Permissible annual depositions and radionuclide concentrations in air

International Nuclear Information System (INIS)

Belyaev, V.A.; Golovko, M.Yu.

1993-01-01

It is established that it necessary to take into account the other ways of radionuclide intake apart from the inhalation one when determining the standards for radionuclide contamination of the atmospheric air. Whereby it is proposed to standardize annual depositions rather than permissible concentration in the atmospheric air for the ways related to radionuclide releases on the ground surface, which is explained by ambiguity of their dry deposition rate from the air. Formulae and results of calculation of standard characteristics are presented. The permissible radionuclide depositions, related to the intake through food chains are calculated with account for diet diversity, agroclimatic and phenological parameters in different regions of the country

Follow My Recommendations: A Personalized Privacy Assistant for Mobile App Permissions

DEFF Research Database (Denmark)

Andersen, Mads Schaarup; Liu, Bin; Schaub, Florian

2016-01-01

Modern smartphone platforms have millions of apps, many of which request permissions to access private data and resources, like user accounts or location. While these smartphone platforms provide varying degrees of control over these permissions, the sheer number of decisions that users are expec...

Water-Pressure Distribution on Seaplane Float

Science.gov (United States)

Thompson, F L

1929-01-01

The investigation presented in this report was conducted for the purpose of determining the distribution and magnitude of water pressures likely to be experienced on seaplane hulls in service. It consisted of the development and construction of apparatus for recording water pressures lasting one one-hundredth second or longer and of flight tests to determine the water pressures on a UO-1 seaplane float under various conditions of taxiing, taking off, and landing. The apparatus developed was found to operate with satisfactory accuracy and is suitable for flight tests on other seaplanes. The tests on the UO-1 showed that maximum pressures of about 6.5 pounds per square inch occur at the step for the full width of the float bottom. Proceeding forward from the step the maximum pressures decrease in magnitude uniformly toward the bow, and the region of highest pressures narrows toward the keel. Immediately abaft the step the maximum pressures are very small, but increase in magnitude toward the stern and there once reached a value of about 5 pounds per square inch. (author)

An Ethics of Permission: A Response to the California End of Life Option Act.

Science.gov (United States)

Nelson, Craig

2016-01-01

An ethics of permission can be helpful in framing a response to the ethical differences surrounding the California End of Life Option Act. Law does not define morality, and reaching a moral understanding demands thorough reflection. An ethics of permission examines the ethical demands of a permissive law for both clinician and patient. Serving the good of the patient, respecting professional conscience, and following the law are three ethical elements. Although developing an ethics of permission includes these three elements, these elements do not exhaust all the moral implications involved. An ethics of permission also includes the importance of exercising professional tolerance in the honoring of clinicians who choose to participate or refuse to participate. In addition, an ethics of permission also provides insight in implementing just and fair behavior among medical professionals.

Probabilistic maximum-value wind prediction for offshore environments

DEFF Research Database (Denmark)

Staid, Andrea; Pinson, Pierre; Guikema, Seth D.

2015-01-01

statistical models to predict the full distribution of the maximum-value wind speeds in a 3 h interval. We take a detailed look at the performance of linear models, generalized additive models and multivariate adaptive regression splines models using meteorological covariates such as gust speed, wind speed......, convective available potential energy, Charnock, mean sea-level pressure and temperature, as given by the European Center for Medium-Range Weather Forecasts forecasts. The models are trained to predict the mean value of maximum wind speed, and the residuals from training the models are used to develop...... the full probabilistic distribution of maximum wind speed. Knowledge of the maximum wind speed for an offshore location within a given period can inform decision-making regarding turbine operations, planned maintenance operations and power grid scheduling in order to improve safety and reliability...

Estimation of maximum pressure in small containments of PWR reactors due to loss of coolant accident in primary circuit; Estimativa da pressao maxima em contencoes de reatores PWR de pequeno porte devido a um acidente de perda de refrigerante no circuito primario

Energy Technology Data Exchange (ETDEWEB)

Mendes Neto, Teofilo [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil); Moreira, Joao Manoel Losada [Centro Tecnologico da Marinha em Sao Paulo (CTMSP), SP (Brazil)

2000-07-01

This work studies the problem of containment pressurization after a LOCA in reactors with small containment free volumes. The relationship between the reactor power and the containment free volume is described with the ratio between the volumes of the primary circuit and of the containment. The maximum pressure in a containment, following a LOCA, obtained after a correlation based on large containment PWR, is around 185 psia for a primary circuit and containment volumes ratio of 0.025. For the same problem, calculations with the CONTEMPT-LT code produced a maximum pressure of 162 psia. The behavior of the temperature after a LOCA to the containment, as a function of the ratio between the primary circuit and containment volume, is such that it increases reaching asymptotically to a maximum; differently, the pressure increases almost linearly with the ratio of volumes. (author)

Blood Pressure Out of the Office: Its Time Has Finally Come.

Science.gov (United States)

Krakoff, Lawrence R

2016-03-01

The diagnosis of hypertension includes measurement of blood pressure out of the office by either 24-hour ambulatory monitoring or home blood pressure monitoring. These methods have led to recognition of "white coat hypertension" (WCH) and "masked hypertension" (MH). Research in the 1930s first demonstrated that blood pressures in the office were often far different from those out of the office, at a time when there was no effective treatment. International attention was focused on another imminent world war and a highly controversial election in the United States. Hypertension was not a priority for concern. From the 1950s onward: (i) epidemiology linked hypertension to risk of cardiovascular disease, (ii) effective and safe drugs for treatment of hypertension appeared, (iii) randomized clinical trials demonstrated that drug treatment of hypertension is highly effective for prevention of cardiovascular disease, and (iv) advances in technology led to development of small, portable devices for recording blood pressure noninvasively at home or during usual activities. Accurate measurement of blood pressure in "real life" is now necessary and feasible for appropriate diagnosis and assessment of treatment. Out-of-office blood pressure measurement is emerging as the standard of care for hypertension. © American Journal of Hypertension, Ltd 2015. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

High pressure experimental water loop

International Nuclear Information System (INIS)

Grenon, M.

1958-01-01

A high pressure experimental water loop has been made for studying the detection and evolution of cladding failure in a pressurized reactor. The loop has been designed for a maximum temperature of 360 deg. C, a maximum of 160 kg/cm 2 and flow rates up to 5 m 3 /h. The entire loop consists of several parts: a main circuit with a canned rotor circulation pump, steam pressurizer, heating tubes, two hydro-cyclones (one de-gasser and one decanter) and one tubular heat exchanger; a continuous purification loop, connected in parallel, comprising pressure reducing valves and resin pots which also allow studies of the stability of resins under pressure, temperature and radiation; following the gas separator is a gas loop for studying the recombination of the radiolytic gases in the steam phase. The preceding circuits, as well as others, return to a low pressure storage circuit. The cold water of the low pressure storage flask is continuously reintroduced into the high pressure main circuit by means of a return pump at a maximum head of 160 kg /cm 2 , and adjusted to the pressurizer level. This loop is also a testing bench for the tight high pressure apparatus. The circulating pump and the connecting flanges (Oak Ridge type) are water-tight. The feed pump and the pressure reducing valves are not; the un-tight ones have a system of leak recovery. To permanently check the tightness the circuit has been fitted with a leak detection system (similar to the HRT one). (author) [fr

A Maximum Radius for Habitable Planets.

Science.gov (United States)

Alibert, Yann

2015-09-01

We compute the maximum radius a planet can have in order to fulfill two constraints that are likely necessary conditions for habitability: 1- surface temperature and pressure compatible with the existence of liquid water, and 2- no ice layer at the bottom of a putative global ocean, that would prevent the operation of the geologic carbon cycle to operate. We demonstrate that, above a given radius, these two constraints cannot be met: in the Super-Earth mass range (1-12 Mearth), the overall maximum that a planet can have varies between 1.8 and 2.3 Rearth. This radius is reduced when considering planets with higher Fe/Si ratios, and taking into account irradiation effects on the structure of the gas envelope.

Intensive versus conventional blood pressure monitoring in a general practice population. The Blood Pressure Reduction in Danish General Practice trial: a randomized controlled parallel group trial.

Science.gov (United States)

Klarskov, Pia; Bang, Lia E; Schultz-Larsen, Peter; Gregers Petersen, Hans; Benee Olsen, David; Berg, Ronan M G; Abrahamsen, Henrik; Wiinberg, Niels

2018-01-17

To compare the effect of a conventional to an intensive blood pressure monitoring regimen on blood pressure in hypertensive patients in the general practice setting. Randomized controlled parallel group trial with 12-month follow-up. One hundred and ten general practices in all regions of Denmark. One thousand forty-eight patients with essential hypertension. Conventional blood pressure monitoring ('usual group') continued usual ad hoc blood pressure monitoring by office blood pressure measurements, while intensive blood pressure monitoring ('intensive group') supplemented this with frequent home blood pressure monitoring and 24-hour ambulatory blood pressure monitoring. Mean day- and night-time systolic and diastolic 24-hour ambulatory blood pressure. Change in systolic and diastolic office blood pressure and change in cardiovascular risk profile. Of the patients, 515 (49%) were allocated to the usual group, and 533 (51%) to the intensive group. The reductions in day- and night-time 24-hour ambulatory blood pressure were similar (usual group: 4.6 ± 13.5/2.8 ± 82 mmHg; intensive group: 5.6 ± 13.0/3.5 ± 8.2 mmHg; P = 0.27/P = 0.20). Cardiovascular risk scores were reduced in both groups at follow-up, but more so in the intensive than in the usual group (P = 0.02). An intensive blood pressure monitoring strategy led to a similar blood pressure reduction to conventional monitoring. However, the intensive strategy appeared to improve patients' cardiovascular risk profile through other effects than a reduction of blood pressure. Clinical Trials NCT00244660. © The Author 2018. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

[Behavior of Orf virus in permissive and nonpermissive systems].

Science.gov (United States)

Büttner, M; Czerny, C P; Schumm, M

1995-04-01

Dogs were immunized i.m. with attenuated poxvirus vaccines (vaccinia virus, Orf-virus) and a bovine herpesvirus-1 (BHV-1) vaccine. After intradermal (i.d.) application of the vaccine viruses a specific delayed type hypersensitivity (DTH) reaction of the skin occurred only with vaccinia virus. The i.d. application of Orf-virus caused a short-term, non-specific inflammatory reaction of the skin, even in dogs not immunized with Orf-virus. Out of 30 sera from Orf-virus immunized beagles (n = 4) only eight were found reactive to Orf-virus in a competition ELISA. Three sera from dogs not Orf-virus immunized but skin-tested with the virus contained low antibody titers. Using indirect immunofluorescence (IIF) in flow cytometry, the existence of Orf-virus antigens was examined on the surface and in the cytoplasm of permissive (BFK and Vero)- and questionable permissive MDCK cells. The canine kidney MDCK cell line was found to be non-permissive for Orf-virus replication; the occurrence of an Orf-(ecthyma contagiosum) like disease in dogs is unlikely.

Suitability of the charm HVS and a microbiological multiplate system for detection of residues in raw milk at EU maximum residue levels

NARCIS (Netherlands)

Nouws, J.F.M.; Egmond, van H.; Loeffen, G.; Schouten, J.; Keukens, H.; Smulders, I.; Stegeman, H.

1999-01-01

In this paper we assessed the suitability of the Charm HVS and a newly developed microbiological multiplate system as post-screening tests to confirm the presence of residues in raw milk at or near the maximum permissible residue level (MRL). The multiplate system is composed of Bacillus

Characteristics of Plantar Loads in Maximum Forward Lunge Tasks in Badminton.

Science.gov (United States)

Hu, Xiaoyue; Li, Jing Xian; Hong, Youlian; Wang, Lin

2015-01-01

Badminton players often perform powerful and long-distance lunges during such competitive matches. The objective of this study is to compare the plantar loads of three one-step maximum forward lunges in badminton. Fifteen right-handed male badminton players participated in the study. Each participant performed five successful maximum lunges at three directions. For each direction, the participant wore three different shoe brands. Plantar loading, including peak pressure, maximum force, and contact area, was measured by using an insole pressure measurement system. Two-way ANOVA with repeated measures was employed to determine the effects of the different lunge directions and different shoes, as well as the interaction of these two variables, on the measurements. The maximum force (MF) on the lateral midfoot was lower when performing left-forward lunges than when performing front-forward lunges (p = 0.006, 95% CI = -2.88 to -0.04%BW). The MF and peak pressures (PP) on the great toe region were lower for the front-forward lunge than for the right-forward lunge (MF, p = 0.047, 95% CI = -3.62 to -0.02%BW; PP, p = 0.048, 95% CI = -37.63 to -0.16 KPa) and left-forward lunge (MF, p = 0.015, 95% CI = -4.39 to -0.38%BW; PP, p = 0.008, 95% CI = -47.76 to -5.91 KPa). These findings indicate that compared with the front-forward lunge, left and right maximum forward lunges induce greater plantar loads on the great toe region of the dominant leg of badminton players. The differences in the plantar loads of the different lunge directions may be potential risks for injuries to the lower extremities of badminton players.

Religiosity and Premarital Sexual Permissiveness: A Response to the Reiss-Heltsley and Broderick Debate

Science.gov (United States)

Ruppel, Howard J., Jr.

1970-01-01

When religiosity among college students was measured by Faulkner and DeJong's 5-D Scale of Religiosity" and the Reiss scale was used to measure permissiveness, the expected stronger relationship between religiosity and permissiveness in groups with traditions of low sexual permissiveness than in groups with traditions of high sexual…

Gender Differences In Premarital Sexual Permissiveness Among ...

African Journals Online (AJOL)

This paper examined the concept of premariatal sexual permissiveness among selected University undergraduates in a state owned university in Nigeria, believing that the policy of non-residential status of the University will facilitate premarital sexual activity among the students. Using a total of 400 purposively selected ...

Secondary poisoning of cadmium, copper and mercury: implications for the Maximum Permissible Concentrations and Negligible Concentrations in water, sediment and soil

NARCIS (Netherlands)

Smit CE; van Wezel AP; Jager T; Traas TP; CSR

2000-01-01

De betekenis van doorvergiftiging voor de Maximum Toelaatbaar Risiconiveau's (MTRs) en Verwaarloosbaar Risiconiveau's (VRs) van cadmium, koper en kwik in water, sediment en bodem is geevalueerd. Veldgegevens met betrekking tot de accumulatie van deze elementen door vissen, mosselen en

Axiomatizations of Banzhaf Permisson Values for Games with a Hierarchical Permission Structure.

NARCIS (Netherlands)

van den Brink, J.R.

2010-01-01

In games with a permission structure it is assumed that players in a cooperative transferable utility game are hierarchically ordered in the sense that there are players that need permission from other players before they are allowed to cooperate. We provide axiomatic characterizations of Banzhaf

Behavior of water gel permissibles in coal mines

Energy Technology Data Exchange (ETDEWEB)

Ribovich, J.; Watson, R.W.

1979-01-01

This paper presents an overview of the successful use of water gel permissibles, since their introduction in 1970, with an emphasis on some problems of behavior in their field application. One is the metal clip or ties used to seal the water gel package. Miners are occasionally hit by the 2.4 mm metal wire expelled from boreholes in normal shooting operations. Manufacturers have consequently reduced the mass of the metal ties by 25-50%, providing a partial solution. Another problem concerned two reported instances of misfired water gel burning after coal shooting operations. Extensive tests have offered no satisfactory solution as yet, except to point up a principal shortcoming of water gels: that of pressure desensitization. Two other factors affecting sensitivity, and possibly resulting in misfires, are low temperature and aging. There is a decline in air-gap sensitivity with prolonged storage but all approved water gels seem capable of meeting requirements for long periods under normal storage conditions. Low temperature tests indicate the majority of water gels become insensitive to a No. 6 EBC at temperatures easily attained in cold weather storage. An attempt was made to determine the minimum temperature at which a nitroglycerin-sensitized permisslbe could be initiated with a No. 8 cap; a particularly granular one was initiated as low as minus 196 C. (5 refs.) (In English)

Performance analysis and comparison of an Atkinson cycle coupled to variable temperature heat reservoirs under maximum power and maximum power density conditions

International Nuclear Information System (INIS)

Wang, P.-Y.; Hou, S.-S.

2005-01-01

In this paper, performance analysis and comparison based on the maximum power and maximum power density conditions have been conducted for an Atkinson cycle coupled to variable temperature heat reservoirs. The Atkinson cycle is internally reversible but externally irreversible, since there is external irreversibility of heat transfer during the processes of constant volume heat addition and constant pressure heat rejection. This study is based purely on classical thermodynamic analysis methodology. It should be especially emphasized that all the results and conclusions are based on classical thermodynamics. The power density, defined as the ratio of power output to maximum specific volume in the cycle, is taken as the optimization objective because it considers the effects of engine size as related to investment cost. The results show that an engine design based on maximum power density with constant effectiveness of the hot and cold side heat exchangers or constant inlet temperature ratio of the heat reservoirs will have smaller size but higher efficiency, compression ratio, expansion ratio and maximum temperature than one based on maximum power. From the view points of engine size and thermal efficiency, an engine design based on maximum power density is better than one based on maximum power conditions. However, due to the higher compression ratio and maximum temperature in the cycle, an engine design based on maximum power density conditions requires tougher materials for engine construction than one based on maximum power conditions

Permissivity of the NCI-60 cancer cell lines to oncolytic Vaccinia Virus GLV-1h68

International Nuclear Information System (INIS)

Ascierto, Maria Libera; Bedognetti, Davide; Uccellini, Lorenzo; Rossano, Fabio; Ascierto, Paolo A; Stroncek, David F; Restifo, Nicholas P; Wang, Ena; Szalay, Aladar A; Marincola, Francesco M; Worschech, Andrea; Yu, Zhiya; Adams, Sharon; Reinboth, Jennifer; Chen, Nanhai G; Pos, Zoltan; Roychoudhuri, Rahul; Di Pasquale, Giovanni

2011-01-01

Oncolytic viral therapy represents an alternative therapeutic strategy for the treatment of cancer. We previously described GLV-1h68, a modified Vaccinia Virus with exclusive tropism for tumor cells, and we observed a cell line-specific relationship between the ability of GLV-1h68 to replicate in vitro and its ability to colonize and eliminate tumor in vivo. In the current study we surveyed the in vitro permissivity to GLV-1h68 replication of the NCI-60 panel of cell lines. Selected cell lines were also tested for permissivity to another Vaccinia Virus and a vesicular stomatitis virus (VSV) strain. In order to identify correlates of permissity to viral infection, we measured transcriptional profiles of the cell lines prior infection. We observed highly heterogeneous permissivity to VACV infection amongst the cell lines. The heterogeneity of permissivity was independent of tissue with the exception of B cell derivation. Cell lines were also tested for permissivity to another Vaccinia Virus and a vesicular stomatitis virus (VSV) strain and a significant correlation was found suggesting a common permissive phenotype. While no clear transcriptional pattern could be identified as predictor of permissivity to infection, some associations were observed suggesting multifactorial basis permissivity to viral infection. Our findings have implications for the design of oncolytic therapies for cancer and offer insights into the nature of permissivity of tumor cells to viral infection

Breakout Session: Fight for Your Right to Copy: How One Library Acquired the Copyright Permissions Service and Reduced Students’ Costs. Presented by Emily Riha, Copyright Permissions Coordinator, University of Minnesota.

Directory of Open Access Journals (Sweden)

Connie Strittmatter

2018-02-01

Full Text Available Emily Riha, Copyright Permissions Coordinator at the University of Minnesota, presented at the 2017 Kraemer Copyright Conference her experience when the process of securing copyright permissions moved from Printing Services to the University Libraries.

Characteristics of Plantar Loads in Maximum Forward Lunge Tasks in Badminton.

Directory of Open Access Journals (Sweden)

Xiaoyue Hu

Full Text Available Badminton players often perform powerful and long-distance lunges during such competitive matches. The objective of this study is to compare the plantar loads of three one-step maximum forward lunges in badminton.Fifteen right-handed male badminton players participated in the study. Each participant performed five successful maximum lunges at three directions. For each direction, the participant wore three different shoe brands. Plantar loading, including peak pressure, maximum force, and contact area, was measured by using an insole pressure measurement system. Two-way ANOVA with repeated measures was employed to determine the effects of the different lunge directions and different shoes, as well as the interaction of these two variables, on the measurements.The maximum force (MF on the lateral midfoot was lower when performing left-forward lunges than when performing front-forward lunges (p = 0.006, 95% CI = -2.88 to -0.04%BW. The MF and peak pressures (PP on the great toe region were lower for the front-forward lunge than for the right-forward lunge (MF, p = 0.047, 95% CI = -3.62 to -0.02%BW; PP, p = 0.048, 95% CI = -37.63 to -0.16 KPa and left-forward lunge (MF, p = 0.015, 95% CI = -4.39 to -0.38%BW; PP, p = 0.008, 95% CI = -47.76 to -5.91 KPa.These findings indicate that compared with the front-forward lunge, left and right maximum forward lunges induce greater plantar loads on the great toe region of the dominant leg of badminton players. The differences in the plantar loads of the different lunge directions may be potential risks for injuries to the lower extremities of badminton players.

26 CFR 1.422-5 - Permissible provisions.

Science.gov (United States)

2010-04-01

... of the incentive stock option are subject to a substantial risk of forfeiture and not transferable...) INCOME TAXES Certain Stock Options § 1.422-5 Permissible provisions. (a) General rule. An option that otherwise qualifies as an incentive stock option does not fail to be an incentive stock option merely...

17 CFR 230.433 - Conditions to permissible post-filing free writing prospectuses.

Science.gov (United States)

2010-04-01

... writing prospectus used at the same time as a communication in a business combination transaction subject... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Conditions to permissible post... Prospectuses § 230.433 Conditions to permissible post-filing free writing prospectuses. (a) Scope of section...

Magnetization at high pressure in CeP

Science.gov (United States)

Naka, T.; Matsumoto, T.; Okayama, Y.; Môri, N.; Haga, Y.; Suzuki, T.

1995-02-01

We have investigated the pressure dependence of magnetization below 60 K up to 1.6 GPa in the low-carrier concentration system CeP showing two step transitions at T = TL and TH under high pressure. At high pressure, M( P, T) exhibits a maximum at around the lower transition temperature TL. This behavior implies that the magnetic state changes at TL. The pressure dependence of isothermal magnetization M( P) is different above and below TL. In fact, M( P) below TL exhibits a maximum at around 1.4 GPa, whereas M( P) above TL increases steeply with pressure up to 1.6 GPa.

Maternal risk factors in fetal alcohol syndrome: provocative and permissive influences.

Science.gov (United States)

Abel, E L; Hannigan, J H

1995-01-01

We present an hypothesis integrating epidemiological, clinical case, and basic biomedical research to explain why only relatively few women who drink alcohol during pregnancy give birth to children with alcohol-related birth defects (ARBDs), in particular, Fetal Alcohol Syndrome (FAS). We argue that specific sociobehavioral risk factors, e.g., low socioeconomic status, are permissive for FAS in that they provide the context for increased vulnerability. We illustrate how these permissive factors are related to biological factors, e.g., decreased antioxidant status, which in conjunction with alcohol, provoke FAS/ARBDs in vulnerable fetuses. We propose an integrative heuristic model hypothesizing that these permissive and provocative factors increase the likelihood of FAS/ARBDs because they potentiate two related mechanisms of alcohol-induced teratogenesis, specifically, maternal/fetal hypoxia and free radical formation.

Assessment of wheel propeller contact pressure upon soil with use of tire universal performance

Directory of Open Access Journals (Sweden)

Z. A. Godzhaev

2016-01-01

Full Text Available A maximum contact pressure is a key parameter characterizing a level of ecological impact of tractor propellers on the soil. The maximum pressure upon the soil varies with internal pressure in tires and vertical load of a wheel. An universal tire performance can be used at an assessment of change of contact pressure of a wheel propeller upon the soil. The authors offered a technique of definition and regulation of the maximum contact pressure of the wheel propeller upon the basic basis. This technique allows to set parameters for monitoring systems and regulation of the maximum pressure upon the soil by measurement of a tire deflection and change of pressure in tires. At statistical tests for determination of the maximum contact pressure it is necessary to consider the universal performance of the tire nomographically. This nomogram allows to consider visually influence of loading and internal pressure in the tire on a size of the maximum contact pressure. An internal pressure decrease in the tire makes it possible to reduce the maximum pressure upon the soil at constant loading. The authors investigated universal performances of the tires in the range of change of internal air pressure from 160 to 90 kPas. Change of internal pressure from 150 to 100 kPas reduce for the tire 15,5R38 the maximum contact pressure upon 13 kPas (9,6 percent: from 135 to 122 kPas. That corresponds to the admissible level of pressure upon the soil at its humidity in a layer of 0-30 cm: 0,5-0,6 minimum moisture-holding capacity during the spring period and 0,6-0,7 minimum moisture-holding capacity during the autumn period. In case of use of the tire 16,9R38 the maximum pressure upon the soil decreases from 84 to 75 kPas, that is by 10,4 percent.

Minimal length, Friedmann equations and maximum density

Energy Technology Data Exchange (ETDEWEB)

Awad, Adel [Center for Theoretical Physics, British University of Egypt,Sherouk City 11837, P.O. Box 43 (Egypt); Department of Physics, Faculty of Science, Ain Shams University,Cairo, 11566 (Egypt); Ali, Ahmed Farag [Centre for Fundamental Physics, Zewail City of Science and Technology,Sheikh Zayed, 12588, Giza (Egypt); Department of Physics, Faculty of Science, Benha University,Benha, 13518 (Egypt)

2014-06-16

Inspired by Jacobson’s thermodynamic approach, Cai et al. have shown the emergence of Friedmann equations from the first law of thermodynamics. We extend Akbar-Cai derivation http://dx.doi.org/10.1103/PhysRevD.75.084003 of Friedmann equations to accommodate a general entropy-area law. Studying the resulted Friedmann equations using a specific entropy-area law, which is motivated by the generalized uncertainty principle (GUP), reveals the existence of a maximum energy density closed to Planck density. Allowing for a general continuous pressure p(ρ,a) leads to bounded curvature invariants and a general nonsingular evolution. In this case, the maximum energy density is reached in a finite time and there is no cosmological evolution beyond this point which leaves the big bang singularity inaccessible from a spacetime prospective. The existence of maximum energy density and a general nonsingular evolution is independent of the equation of state and the spacial curvature k. As an example we study the evolution of the equation of state p=ωρ through its phase-space diagram to show the existence of a maximum energy which is reachable in a finite time.

Measurement of in-bore side loads and comparison to first maximum yaw

Directory of Open Access Journals (Sweden)

Donald E. Carlucci

2016-04-01

Full Text Available In-bore yaw of a projectile in a gun tube has been shown to result in range loss if the yaw is significant. An attempt was made to determine if relationships between in-bore yaw and projectile First Maximum Yaw (FMY were observable. Experiments were conducted in which pressure transducers were mounted near the muzzle of a 155 mm cannon in three sets of four. Each set formed a cruciform pattern to obtain a differential pressure across the projectile. These data were then integrated to form a picture of what the overall pressure distribution was along the side of the projectile. The pressure distribution was used to determine a magnitude and direction of the overturning moment acting on the projectile. This moment and its resulting angular acceleration were then compared to the actual first maximum yaw observed in the test. The degree of correlation was examined using various statistical techniques. Overall uncertainty in the projectile dynamics was between 20% and 40% of the mean values of FMY.

New system for measuring and controlling the maximum pressing pressure in the holes of the mould: ISOPRESS; Nuevo sistema para la medida y control de la presion maxima de prensado en los alveolos del molde: ISOPRESS

Energy Technology Data Exchange (ETDEWEB)

Poyatos, A.; Bonaque, R.; Mallol, G.; Boix, J.

2012-07-01

The organization MACER, in collaboration with the Institute of Ceramic Technology, has developed the system ISOPRESS, an integrated control device that permits to equal automatically the maximum pressure applied on the powder contained in each of the holes of the mould. This system consists of a set of pressure transducers which are located in the isostatic punches of the mould itself. With them it is possible to register in real-time the evolution of the measured pressure of the oil contained in the compensation chamber of each punch. All the transducers are connected to a data acquisition system which transfers the pressure values to a PC which performs the signal processing to obtain the pressure maximum value reached during a pressing cycle, in each one of the holes. The system is completed with a control software especially developed, that permits to regulate individually the height of the first fall of each inferior punch to guarantee the uniformity of the pressure applied in all the holes. ISOPRESS, by assuring the constancy of the bulk density of all the pieces processed, guarantees a unique piece size and minimize production problems associated to the variability of the bulk density of the pieces. (Author)

A Dynamic Operation Permission Technique Based on an MFM Model and Numerical Simulation

International Nuclear Information System (INIS)

Akio, Gofuku; Masahiro, Yonemura

2011-01-01

It is important to support operator activities to an abnormal plant situation where many counter actions are taken in relatively short time. The authors proposed a technique called dynamic operation permission to decrease human errors without eliminating creative idea of operators to cope with an abnormal plant situation by checking if the counter action taken is consistent with emergency operation procedure. If the counter action is inconsistent, a dynamic operation permission system warns it to operators. It also explains how and why the counter action is inconsistent and what influence will appear on the future plant behavior by a qualitative influence inference technique based on a model by the Mf (Multilevel Flow Modeling). However, the previous dynamic operation permission is not able to explain quantitative effects on plant future behavior. Moreover, many possible influence paths are derived because a qualitative reasoning does not give a solution when positive and negative influences are propagated to the same node. This study extends the dynamic operation permission by combining the qualitative reasoning and the numerical simulation technique. The qualitative reasoning based on an Mf model of plant derives all possible influence propagation paths. Then, a numerical simulation gives a prediction of plant future behavior in the case of taking a counter action. The influence propagation that does not coincide with the simulation results is excluded from possible influence paths. The extended technique is implemented in a dynamic operation permission system for an oil refinery plant. An MFM model and a static numerical simulator are developed. The results of dynamic operation permission for some abnormal plant situations show the improvement of the accuracy of dynamic operation permission and the quality of explanation for the effects of the counter action taken

Procedures for permission under atomic energy laws in the Federal Republic of Germany

International Nuclear Information System (INIS)

Kuhnt, D.

1980-01-01

The selection of proper locations by the enterprisers responsible for projects is usually accompanied in recent years by the active location policy of the state. The application for the permission of locations and projects shall be filed to one or more ministries of the province where the facilities are to be installed. The papers describing the projects, especially safety reports and summaries shall be attached to the applications. The applications shall be published on a bulletin of the government office or daily newspapers, and every person has access to the applications, the safety reports and the summaries for two months. When objections are lodged within the period, closed hearings are held to examine the protests with attendance of the objector, the enterpriser of the project and the government office which has joined the decision. Following the phase of public participation and after the confirmation of facts highly important to the decision, fact examination is carried out with cooperation of specialists by the government office authorized for permission. As a special feature of the procedures under Atomgesetz, the government office is not necessarily obliged to give permission considering the safety policy, even when the pre-requisites of permission are all fulfilled. In other respects, permission may be offered for each partial installation of the facilities and various stages of operation by particular administrative measures (partial permission). The experiences of past 20 years indicate the virtual defects of the laws applied, and the amendment is urgently required. (Okada, K.)

In-shoe plantar tri-axial stress profiles during maximum-effort cutting maneuvers.

Science.gov (United States)

Cong, Yan; Lam, Wing Kai; Cheung, Jason Tak-Man; Zhang, Ming

2014-12-18

Soft tissue injuries, such as anterior cruciate ligament rupture, ankle sprain and foot skin problems, frequently occur during cutting maneuvers. These injuries are often regarded as associated with abnormal joint torque and interfacial friction caused by excessive external and in-shoe shear forces. This study simultaneously investigated the dynamic in-shoe localized plantar pressure and shear stress during lateral shuffling and 45° sidestep cutting maneuvers. Tri-axial force transducers were affixed at the first and second metatarsal heads, lateral forefoot, and heel regions in the midsole of a basketball shoe. Seventeen basketball players executed both cutting maneuvers with maximum efforts. Lateral shuffling cutting had a larger mediolateral braking force than 45° sidestep cutting. This large braking force was concentrated at the first metatarsal head, as indicated by its maximum medial shear stress (312.2 ± 157.0 kPa). During propulsion phase, peak shear stress occurred at the second metatarsal head (271.3 ± 124.3 kPa). Compared with lateral shuffling cutting, 45° sidestep cutting produced larger peak propulsion shear stress (463.0 ± 272.6 kPa) but smaller peak braking shear stress (184.8 ± 181.7 kPa), of which both were found at the first metatarsal head. During both cutting maneuvers, maximum medial and posterior shear stress occurred at the first metatarsal head, whereas maximum pressure occurred at the second metatarsal head. The first and second metatarsal heads sustained relatively high pressure and shear stress and were expected to be susceptible to plantar tissue discomfort or injury. Due to different stress distribution, distinct pressure and shear cushioning mechanisms in basketball footwear might be considered over different foot regions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Parental permissiveness, control, and affect and drug use among adolescents.

Science.gov (United States)

Becoña, Elisardo; Martínez, Úrsula; Calafat, Amador; Fernández-Hermida, José Ramón; Juan, Montse; Sumnall, Harry; Mendes, Fernando; Gabrhelík, Roman

2013-01-01

Parents play an important role in determining the risk of children's drug use. The aim of this study was to analyse how certain family-related variables (permissiveness toward drug use, and parental control and affect) were linked to the use of alcohol, tobacco and cannabis, based on young people's self-report of such variables. The sample was composed of 1,428 school children (51.8% males) aged between 11 and 19 from Mallorca (Spain). We found that the young people who perceived their parents as permissive and those who perceived less maternal control and higher levels of both paternal and maternal affect were more likely to use alcohol, tobacco and cannabis. Sex differences were found within this pattern. Variables of maternal affect and control were not influential among males, whereas the general pattern was maintained among females. This study highlights the importance of perceived permissiveness and the need of considering parent's and children's gender when providing control and affect, as fathers will influence male children whereas mothers will influence female children.

Maximum mass of magnetic white dwarfs

International Nuclear Information System (INIS)

Paret, Daryel Manreza; Horvath, Jorge Ernesto; Martínez, Aurora Perez

2015-01-01

We revisit the problem of the maximum masses of magnetized white dwarfs (WDs). The impact of a strong magnetic field on the structure equations is addressed. The pressures become anisotropic due to the presence of the magnetic field and split into parallel and perpendicular components. We first construct stable solutions of the Tolman-Oppenheimer-Volkoff equations for parallel pressures and find that physical solutions vanish for the perpendicular pressure when B ≳ 10 13 G. This fact establishes an upper bound for a magnetic field and the stability of the configurations in the (quasi) spherical approximation. Our findings also indicate that it is not possible to obtain stable magnetized WDs with super-Chandrasekhar masses because the values of the magnetic field needed for them are higher than this bound. To proceed into the anisotropic regime, we can apply results for structure equations appropriate for a cylindrical metric with anisotropic pressures that were derived in our previous work. From the solutions of the structure equations in cylindrical symmetry we have confirmed the same bound for B ∼ 10 13 G, since beyond this value no physical solutions are possible. Our tentative conclusion is that massive WDs with masses well beyond the Chandrasekhar limit do not constitute stable solutions and should not exist. (paper)

Permissive parenting and mental health in college students: Mediating effects of academic entitlement.

Science.gov (United States)

Barton, Alison L; Hirsch, Jameson K

2016-01-01

Student mental health may suffer due to unreasonable expectations associated with academic entitlement; permissive parenting may be one source of these expectations. The authors examined the role of academic entitlement as a mediator of the relationship between permissive parenting and psychological functioning. Participants were 524 undergraduate students at a single institution (52% female; age range = 18-22). Data collection was completed in May 2011. Cross-sectional design. Participants completed online self-report measures of parenting styles, academic entitlement, stress, depressive symptoms, and well-being. Permissive parenting was associated with greater academic entitlement and, in turn, to more perceived stress and poorer mental health. Mother/father differences were found in some cases. Academic entitlement may partially explain why permissive parenting is detrimentally related to mental health for college students. Implications for academic affairs and counseling include helping students develop an appreciation of the role of self-regulation in college success.

Permissive Parenting and Mental Health in College Students: Mediating Effects of Academic Entitlement

Science.gov (United States)

Barton, Alison L.; Hirsch, Jameson K.

2016-01-01

Objective: Student mental health may suffer due to unreasonable expectations associated with academic entitlement; permissive parenting may be one source of these expectations. The authors examined the role of academic entitlement as a mediator of the relationship between permissive parenting and psychological functioning. Participants:…

50 CFR 216.252 - Permissible methods of taking.

Science.gov (United States)

2010-10-01

... ADMINISTRATION, DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking Marine Mammals Incidental to Conducting Precision Strike Weapon Missions in the Gulf of Mexico § 216.252 Permissible methods of taking. (a) Under Letters of Authorization issued pursuant to...

Pressure test method for reactor pressure vessel in construction field

International Nuclear Information System (INIS)

Takeda, Masakado; Ushiroda, Koichi; Miyahara, Ryohei; Takano, Hiroshi; Matsuura, Tadashi; Sato, Keiya.

1998-01-01

Plant constitutional parts as targets of both of a primary pressure test and a secondary pressure test are disposed in communication with a reactor pressure vessel, and a pressure of the primary pressure test is applied to the targets of both tests, so that the primary pressure test and the second pressure test are conducted together. Since the number of pressure tests can be reduced to promote construction, and the number of workers can also be reduced. A pressure exceeding the maximum pressure upon use is applied to the pressure vessel after disposing the incore structures, to continuously conduct the primary pressure test and the secondary pressure test joined together and an incore flowing test while closing the upper lid of the pressure vessel as it is in the construction field. The number of opening/closing of the upper lid upon conducting every test can be reduced, and since the pressure resistance test is conducted after arranging circumference conditions for the incore flowing test, the tests can be conducted collectively also in view of time. (N.H.)

Potential hydrogen and oxygen partial pressures in legacy plutonium oxide packages at Oak Ridge

Energy Technology Data Exchange (ETDEWEB)

Veirs, Douglas K. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-07-07

An approach to estimate the maximum hydrogen and oxygen partial pressures within sealed containers is described and applied to a set of packages containing high-purity plutonium dioxide. The approach uses experimentally determined maximum hydrogen and oxygen partial pressures and scales the experimentally determined pressures to the relevant packaged material properties. The important material properties are the specific wattage and specific surface area (SSA). Important results from the experimental determination of maximum partial pressures are (1) the ratio of hydrogen to oxygen is stoichiometric, and (2) the maximum pressures increase with increasing initial rates of production. The material properties that influence the rates are the material specific wattage and the SSA. The unusual properties of these materials, high specific wattage and high SSA, result in higher predicted maximum pressures than typical plutonium dioxide in storage. The pressures are well within the deflagration range for mixtures of hydrogen and oxygen.

50 CFR 216.213 - Permissible methods of taking.

Science.gov (United States)

2010-10-01

... ADMINISTRATION, DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking of Marine Mammals Incidental to Explosive Severance Activities Conducted During Offshore Structure Removal Operations on the Outer Continental Shelf in the U.S. Gulf of Mexico § 216.213 Permissible...

36 CFR 223.12 - Permission to cut, damage, or destroy trees without advertisement.

Science.gov (United States)

2010-07-01

... destroy trees without advertisement. 223.12 Section 223.12 Parks, Forests, and Public Property FOREST... § 223.12 Permission to cut, damage, or destroy trees without advertisement. Permission may be granted to cut, damage, or destroy trees, portions of trees, or other forest products on National Forest System...

47 CFR 74.790 - Permissible service of digital TV translator and LPTV stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Permissible service of digital TV translator... DISTRIBUTIONAL SERVICES Low Power TV, TV Translator, and TV Booster Stations § 74.790 Permissible service of digital TV translator and LPTV stations. (a) Digital TV translator stations provide a means whereby the...

Permissiveness toward tobacco sponsorship undermines tobacco control support in Africa.

Science.gov (United States)

Ayo-Yusuf, Olalekan A; Olutola, Bukola G; Agaku, Israel T

2016-06-01

School personnel, who are respected members of the community, may exert significant influence on policy adoption. This study assessed the impact of school personnel's permissiveness toward tobacco industry sponsorship activities on their support for complete bans on tobacco advertisements, comprehensive smoke-free laws and increased tobacco prices. Representative data were obtained from the Global School Personnel Survey for 29 African countries (n = 17 929). Adjusted prevalence ratios (aPR) were calculated using multi-variable Poisson regression models to assess the impact of permissiveness toward tobacco sponsorship activities on support for tobacco control policies (p industry should be allowed to sponsor school events were significantly less likely to support complete bans on tobacco advertisements [aPR = 0.89; 95% confidence interval (CI) 0.84-0.95] and comprehensive smoke-free laws (aPR = 0.95; 95% CI 0.92-0.98). In contrast, support for complete tobacco advertisement bans was more likely among those who believed that the tobacco industry encourages youths to smoke (aPR = 1.27; 95% CI 1.17-1.37), and among those who taught about health sometimes (aPR = 1.06; 95% CI 1.01-1.11) or a lot (aPR = 1.05; 95% CI 1.01-1.10) compared with those who did not teach about health at all. These findings underscore the need to educate school personnel on tobacco industry's strategies to undermine tobacco control policies. This may help to build school personnel support for laws intended to reduce youth susceptibility, experimentation and established use of tobacco products. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Legitimate Permissions And Specifity Of Their Enforceability In Modern Russia

Directory of Open Access Journals (Sweden)

Vitaly Subochev

2014-01-01

Full Text Available Northern Caucasus Institute of Advanced Training (branch of Krasnodar University of Ministry of Internal Affairs of Russia, 123, Malbahova Street, Nalshik, 360016, Russia. Abstract: The article investigates the basic legal permissions in Russian law - legal rights, freedoms and legitimate interests. Potential of these means of legal regulation is examined as well as their common features and essential differences. Authors argue that the effectiveness of the mechanism of legal regulation largely depends on the proper use of legal permissions. Particular attention is paid to such kind of legal mean as a legitimate interest. The article draws attention to the fact that if a legal right or freedom are such kind of permissions which are guaranteed by the law in order to sustain certain demands of subjects of law, the legitimate interest is qualitatively different mean of regulation. The authors suggest considering a legitimate interest as reflected in the objective law legal possibility of subjects of law to enjoy certain social benefits and to seek protection from the state authorities in order to meet their interests which are not contradictory to provisions of law. Qualitative difference between legitimate interest and legal right and freedom is that the legitimate interest is an opportunity, guaranteed to a lesser extent than the permitted behavior within a legal right or freedom. Legitimate interest is a mere permission, admitted by the state and to some extent supported by it. But legal right and freedom - are those means of regulation, which are directly approved and sanctioned by the state which presuppose duty of a person to a particular behavior. The author's vision of the specifity of legal enforcement of legitimate admissions is presented.

LEGITIMATE PERMISSIONS AND SPECIFITY OF THEIR ENFORCEABILITY IN MODERN RUSSIA

Directory of Open Access Journals (Sweden)

Vitaly Subochev

2014-01-01

Full Text Available Northern Caucasus Institute of Advanced Training (branch of Krasnodar University of Ministry of Internal Affairs of Russia, 123, Malbahova Street, Nalshik, 360016, Russia. Abstract: The article investigates the basic legal permissions in Russian law - legal rights, freedoms and legitimate interests. Potential of these means of legal regulation is examined as well as their common features and essential differences. Authors argue that the effectiveness of the mechanism of legal regulation largely depends on the proper use of legal permissions. Particular attention is paid to such kind of legal mean as a legitimate interest. The article draws attention to the fact that if a legal right or freedom are such kind of permissions which are guaranteed by the law in order to sustain certain demands of subjects of law, the legitimate interest is qualitatively different mean of regulation. The authors suggest considering a legitimate interest as reflected in the objective law legal possibility of subjects of law to enjoy certain social benefits and to seek protection from the state authorities in order to meet their interests which are not contradictory to provisions of law. Qualitative difference between legitimate interest and legal right and freedom is that the legitimate interest is an opportunity, guaranteed to a lesser extent than the permitted behavior within a legal right or freedom. Legitimate interest is a mere permission, admitted by the state and to some extent supported by it. But legal right and freedom - are those means of regulation, which are directly approved and sanctioned by the state which presuppose duty of a person to a particular behavior. The author's vision of the specifity of legal enforcement of legitimate admissions is presented.

A new model for deteriorating items with inflation under permissible delay in payments

Directory of Open Access Journals (Sweden)

R.P. Tripathi

2014-05-01

Full Text Available Inflation is an important factor influencing traditional economic order quality models. Marketing strategy depends on inflation due to public demand and availability of the materials. This paper presents an optimal inventory policy for deteriorating items using exponential demand rate under permissible delay in payments. Mathematical model has been derived under two cases: case I: cycle time is greater than or equal to permissible delay period, case II: cycle time is less than permissible delay period by considering holding cost as a function of time. Numerical examples and sensitivity analysis are given to reflect the numerical results. Mathematica software is used for finding optimal solutions.

Determination of permissible exposure doses under the provisions of the regulations on installation and operation of marine reactors

International Nuclear Information System (INIS)

1979-01-01

The Ministry of Transportation defines on radioactive doses in the controlled area that exterior radioactive dose shall be 30 mili-rem for a week; concentrations of radioactive materials in the air or under the water shall be permissible concentrations otherwise specified for the employees multiplied by 0.75 in average for a week and that densities of radioactive materials on the surface of the things contaminated by such materials shall be 1/10 of permissible surface densities provided in a table attached. Permissible exposure dose outside the inspected surrounding area is 0.5 rem for a year. Permissible surface densities are included in a list attached. Permissible accumulative dose for the employees is the figure (unit rem) calculated by the formula D = 5(N-18), when D means permissible accumulative dose and N number of the age. Permissible exposure dose is 3 rem for 3 months for the employees, 1.5 rem for a year for persons other than the employees and 12 rem for the urgent work. Permissible densities for the employees, calculation of doses by interior exposure and permissible densities outside the inspected surrounding area are stipulated in detail with attached lists. (Okada, K.)

Heat Convection at the Density Maximum Point of Water

Science.gov (United States)

Balta, Nuri; Korganci, Nuri

2018-01-01

Water exhibits a maximum in density at normal pressure at around 4° degree temperature. This paper demonstrates that during cooling, at around 4 °C, the temperature remains constant for a while because of heat exchange associated with convective currents inside the water. Superficial approach implies it as a new anomaly of water, but actually it…

Blood Pressure of Jordanian Workers Chronically Exposed to Noise in Industrial Plants

Directory of Open Access Journals (Sweden)

Saed Nserat

2017-10-01

Full Text Available Background: Occupational studies investigating the association between blood pressure and noise exposure are almost lacking in the Eastern Mediterranean Region countries. Objective: To determine the association between occupational exposure to high level of noise and blood pressure among a group of workers in Jordan. Methods: All workers who had been exposing to noise for at least 3 years in 3 plants in Madaba governorate in Jordan were included in this cross-sectional study. A structured questionnaire was used to collect data. The occupational noise level was measured with a portable calibrated sound meter. Results: We studied 191 male workers, of whom 145 (75.9% were exposed to a noise level higher than the permissible limit of 85 dBA. The mean systolic blood pressure (SBP and diastolic blood pressure (DBP and the prevalence of hypertension were significantly higher among those exposed to higher noise level. In multivariate analysis, workers exposed to high level of noise had a significantly higher odds of hypertension compared to those exposed to noise level lower than the permissible limit (OR 4.7, 95% CI 1.6 to 13.8. The odds of hypertension increased by 17% (95% CI 10% to 30% for each dB increase in noise intensity. Conclusion: Exposure to high level of noise is associated with elevated blood pressure.

Influence of Permissive Parenting on Youth Farm Risk Behaviors.

Science.gov (United States)

Jinnah, Hamida A; Stoneman, Zolinda

2016-01-01

Farm youth continue to experience high rates of injuries and premature deaths as a result of agricultural activities. Increased parental permissiveness is positively associated with many different types of high-risk behaviors in youth. This study explored whether permissive parenting (fathering and mothering) predicts youth unsafe behaviors on the farm. Data were analyzed for 67 youth and their parents. Families were recruited from a statewide farm publication, through youth organizations (i.e., FFA [Future Farmers of America]), local newspapers, farmer referrals, and through the Cooperative Extension Network. Hierarchical multiple regression was completed. Results revealed that fathers and mothers who practiced lax-inconsistent disciplining were more likely to have youth who indulged in unsafe farm behaviors. Key hypotheses confirmed that permissive parenting (lax-inconsistent disciplining) by parents continued to predict youth unsafe farm behaviors, even after youth age, youth gender, youth personality factor of risk-taking, and father's unsafe behaviors (a measure associated with modeling) were all taken into account. A key implication is that parents may play an important role in influencing youth farm safety behaviors. Parents (especially fathers) need to devote time to discuss farm safety with their youth. Farm safety interventions need to involve parents as well as address and respect the culture and values of families. Interventions need to focus not only on safe farm practices, but also promote positive parenting practices, including increased parent-youth communication about safety, consistent disciplining strategies, and increased monitoring and modeling of safe farm behaviors by parents.

Influence of bronchial diameter change on the airflow dynamics based on a pressure-controlled ventilation system.

Science.gov (United States)

Ren, Shuai; Cai, Maolin; Shi, Yan; Xu, Weiqing; Zhang, Xiaohua Douglas

2018-03-01

Bronchial diameter is a key parameter that affects the respiratory treatment of mechanically ventilated patients. In this paper, to reveal the influence of bronchial diameter on the airflow dynamics of pressure-controlled mechanically ventilated patients, a new respiratory system model is presented that combines multigeneration airways with lungs. Furthermore, experiments and simulation studies to verify the model are performed. Finally, through the simulation study, it can be determined that in airway generations 2 to 7, when the diameter is reduced to half of the original value, the maximum air pressure (maximum air pressure in lungs) decreases by nearly 16%, the maximum flow decreases by nearly 30%, and the total airway pressure loss (sum of each generation pressure drop) is more than 5 times the original value. Moreover, in airway generations 8 to 16, with increasing diameter, the maximum air pressure, maximum flow, and total airway pressure loss remain almost constant. When the diameter is reduced to half of the original value, the maximum air pressure decreases by 3%, the maximum flow decreases by nearly 5%, and the total airway pressure loss increases by 200%. The study creates a foundation for improvement in respiratory disease diagnosis and treatment. Copyright © 2017 John Wiley & Sons, Ltd.

Effect of pressure on transport properties of CeIrIn5

International Nuclear Information System (INIS)

Takaesu, Y; Aso, N; Tamaki, Y; Hedo, M; Nakama, T; Uchima, K; Ishikawa, Y; Deguchi, K; Sato, N K

2011-01-01

Electrical resistivity ρ and thermoelectric power S of a heavy-fermion superconductor CeIrIn 5 have been measured at temperatures from 2.0 K to 300 K under hydrostatic pressures up to 2.2 GPa. The thermoelectric power S exhibits a large positive value up to 90 μV/K, which is characteristic of heavy-fermion systems. S also shows a sharp maximum in its temperature dependence and its maximum temperature T s,max increases with pressure, while its maximum value is constant independent of pressure. These experimental results strongly indicate that the Kondo temperature of CeIrIn 5 increases by applying the pressure.

20 CFR 416.1321 - Suspension for not giving us permission to contact financial institutions.

Science.gov (United States)

2010-04-01

... contact financial institutions. 416.1321 Section 416.1321 Employees' Benefits SOCIAL SECURITY....1321 Suspension for not giving us permission to contact financial institutions. (a) If you don't give us permission to contact any financial institution and request any financial records about you when...

Synthesis of microparticles with complex compositions in a xenon high-pressure chamber (550 bar) under irradiation by braking radiation with a maximum energy of 10 MeV

International Nuclear Information System (INIS)

Didyk, A.Yu.; Gul'bekyan, G.G.; Myshinskiy, G.V.; Sabel'nikov, A.V.

2016-01-01

Natural xenon at a pressure of 550 bar in a high pressure chamber (XeHPC) was irradiated during 2,59 · 10 5 s by bremsstrahlung with a maximum energy of 10 MeV at the electron accelerator MT-25 microtron with an electron beam intensity of 20–22μA. The final electron fluence was 4.74 · 10 19 electrons. The growth of pressure versus temperature during the stationary exposure mode grew at first up to 620 bar and then dropped to 550 bar. After opening of the XeHPC both of the internal chambers with all the structures, but without gas, were measured using a γ-germanium detector (Canberra) during 15 h each for measurement of the background and short-lived isotopes. During a visual inspection of the interior surfaces of the XeHPC inner assembly, a visible coating of substantial thickness and greenish-yellowish color was observed. The research carried out by scanning electron microscopy (SEM) and X-ray micro-probe analysis (XMPA) allowed us to determine the elemental composition of synthesized particles. [ru

Research on axial total pressure distributions of sonic steam jet in subcooled water

International Nuclear Information System (INIS)

Wu Xinzhuang; Li Wenjun; Yan Junjie

2012-01-01

The axial total pressure distributions of sonic steam jet in subcooled water were experimentally investigated for three different nozzle diameters (6.0 mm, 8.0 mm and 10.0 mm). The inlet steam pressure, and pool subcooling subcooled water temperature were in the range of 0.2-0.6 MPa and 420-860 ℃, respectively. The effect of steam pressure, subcooling water temperature and nozzle size on the axial pressure distributions were obtained, and also the characteristics of the maximum pressure and its position were studied. The results indicated that the characteristics of the maximum pressure were influenced by the nozzle size for low steam pressure, but the influence could be ignored for high steam pressure. Moreover, a correlation was given to correlate the position of the maximum pressure based on steam pressure and subcooling water temperature, and the discrepancies of predictions and experiments are within ±15%. (authors)

Maximum overpressure in gastight containers of the storage and transport of dangerous liquids

International Nuclear Information System (INIS)

Steen, H.

1977-11-01

For a design of containers suitable under safety aspects for the transport and storage of dangerous liquids the maximum overpressure to be expected is an important value. The fundamentals for the determination of the internal pressure are pointed out for the simplified model of a rigid (i.e. not elastically or plastically deforming) and gastight container. By assuming of extreme storage and transport conditions (e.g. for the maximum liquid temperatures due to sun radiation) the figures of the maximum overpressure are calculated for about hundred liquids being of practical interest. The results show a significant influence of the compression of air in the ullage space caused by liquid expansion due to temperature rise (compression effect), particularly for liquids with a higher boiling point. The influence of the solubility of air in the liquid on the internal pressure can be neglected under the assumed transport conditions. The estimation of the volume increase of the container due to the effect of the internal pressure leads to the limitation, that the assumption of a rigid container is only justified for cylindrical and spherical steel tanks. The enlargement of the container volume due to a heating of the container shell does play no significant roll for all metal containers under the assumed conditions of storage and transport. The results obtained bear out essentially the stipulations for the test pressure and the filling limits laid down in the older German regulations for the transport of dangerous liquids in rail tank waggons and road tank vehicles without pressure relief valves. For the recently fixed and internationally harmonized regulations for tankcontainers the considerations and the results pointed out in this paper give rise to a review. (orig.) [de

Early alcohol use with parental permission: Psychosocial characteristics and drinking in late adolescence.

Science.gov (United States)

Colder, Craig R; Shyhalla, Kathleen; Frndak, Seth E

2018-01-01

The earliest experiences with alcohol for many children occur in the family context with parental supervision. The current study examined individual and sociocultural characteristics associated with early (prior to age 13years) sipping and tasting alcohol with parental permission in two longitudinal community samples. Early sipping/tasting was also tested as a predictor of frequency and quantity of alcohol use, and alcohol-related problems seven years later in late adolescence. Early sipping/tasting with parental permission was associated with a sociocultural context supportive of alcohol use (e.g., parental alcohol use, permissive rules about alcohol use in the home, parental attitudes about underage drinking, perceived peer norms), adolescent sensation seeking and disinhibition (e.g., surgency, externalizing behavior) and appraisals of alcohol (negative outcome expectancies and negative implicit alcohol associations). Early sipping/tasting predicted increased frequency and quantity of alcohol consumption, and increased alcohol-related problems in late adolescence, even after controlling sociocultural and individual difference variables. Findings suggest that early sipping/tasting with parental permission is not benign and is a viable target for preventive interventions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Power converter with maximum power point tracking MPPT for small wind-electric pumping systems

International Nuclear Information System (INIS)

Lara, David; Merino, Gabriel; Salazar, Lautaro

2015-01-01

Highlights: • We implement a wind electric pumping system of small power. • The power converter allowed to change the operating point of the electro pump. • Two control techniques were implemented in the power converter. • The control V/f variable allowed to increase the power generated by the permanent magnet generator. - Abstract: In this work, an AC–DC–AC direct-drive power converter was implemented for a wind electric pumping system consisting of a permanent magnet generator (PMG) of 1.3 kW and a peripheral single phase pump of 0.74 kW. In addition, the inverter linear V/f control scheme and the maximum power point tracking (MPPT) algorithm with variable V/f were developed. MPPT algorithm seeks to extract water in a wide range of power input using the maximum amount of wind power available. Experimental trials at different pump pressures were conducted. With a MPPT tracking system with variable V/f, a power value of 1.3 kW was obtained at a speed of 350 rpm and a maximum operating hydraulic head of 50 m. At lower operating heads pressures (between 10 and 40 m), variable V/f control increases the power generated by the PMG compared to the linear V/f control. This increase ranged between 4% and 23% depending on the operating pressure, with an average of 13%, getting close to the maximum electrical power curve of the PMG. The pump was driven at variable frequency reaching a minimum speed of 0.5 times the rated speed. Efficiency of the power converter ranges between 70% and 95% with a power factor between 0.4 and 0.85, depending on the operating pressure

Relationship Between Urinary Nitrate Excretion and Blood Pressure in the InChianti Cohort.

Science.gov (United States)

Smallwood, Miranda J; Ble, Alessandro; Melzer, David; Winyard, Paul G; Benjamin, Nigel; Shore, Angela C; Gilchrist, Mark

2017-07-01

Inorganic nitrate from the oxidation of endogenously synthesized nitric oxide (NO) or consumed in the diet can be reduced to NO via a complex enterosalivary circulation pathway. The relationship between total nitrate exposure by measured urinary nitrate excretion and blood pressure in a large population sample has not been assessed previously. For this cross-sectional study, 24-hour urinary nitrate excretion was measured by spectrophotometry in the 919 participants from the InChianti cohort at baseline and blood pressure measured with a mercury sphygmomanometer. After adjusting for age and sex only, diastolic blood pressure was 1.9 mm Hg lower in subjects with ≥2 mmol urinary nitrate excretion compared with those excreting nitrate in 24 hours: systolic blood pressure was 3.4 mm Hg (95% confidence interval (CI): -3.5 to -0.4) lower in subjects for the same comparison. Effect sizes in fully adjusted models (for age, sex, potassium intake, use of antihypertensive medications, diabetes, HS-CRP, or current smoking status) were marginally larger: systolic blood pressure in the ≥2 mmol urinary nitrate excretion group was 3.9 (CI: -7.1 to -0.7) mm Hg lower than in the comparison nitrate exposure are associated with lower blood pressure. These differences are at least equivalent to those seen from substantial (100 mmol) reductions in sodium intake. © American Journal of Hypertension, Ltd 2017. All rights reserved. For Permissions, please email: journals.permissions@oup.com

Drug evaluation and the permissive principle: continuities and contradictions between standards and practices in antidepressant regulation.

Science.gov (United States)

Abraham, John; Davis, Courtney

2009-08-01

Pharmaceuticals are not permitted on to the market unless they are granted regulatory approval. The regulatory process is, therefore, crucial in whether or not a drug is widely prescribed. Regulatory agencies have developed standards of performance that pharmaceuticals are supposed to meet before entering the market. Regulation of technologies is often discussed by reference to the precautionary principle. In contrast, this paper develops the concept of the 'permissive principle' as a way of understanding the departure of regulators' practices from standards of drug efficacy to which regulatory agencies themselves subscribe. By taking a case study of antidepressant regulation in the UK and the USA, the mechanisms of permissive regulatory practices are examined. An STS methodology of both spatial (international) and temporal comparisons of regulatory practices with regulatory standards is employed to identify the nature and extent of the permissive regulation. It is found that the permissive principle was adopted by drug regulators in the UK and the USA, but more so by the former than the latter. Evidently, permissive regulation, which favours the commercial interests of the drug manufacturer, but is contrary to the interests of patients, may penetrate to the heart of regulatory science. On the other hand, permissive regulation of specific drugs should not be regarded as an inevitable result of marketing strategies and concomitant networks deployed by powerful pharmaceutical companies, because the extent of permissive regulation may vary according to the intra-institutional normative commitments of regulators to uphold their technical standards against the commercial interests of the manufacturer. Likely sociological factors that can account for such permissive regulatory practices are 'corporate bias', secrecy and excessive regulatory trust in the pharmaceutical industry in the UK, political expediency and ideological capture in the USA, combined in both countries

A single-blinded randomised clinical trial of permissive underfeeding in patients requiring parenteral nutrition.

Science.gov (United States)

Owais, Anwar Elias; Kabir, Syed Irfan; Mcnaught, Clare; Gatt, Marcel; MacFie, John

2014-12-01

The importance of adequate nutritional support is well established, but characterising what 'adequate nutrition' represents remains contentious. In recent years there has been increasing interest in the concept of 'permissive underfeeding' where patients are intentionally prescribed less nutrition than their calculated requirements. The aim of this study was to evaluate the effect of permissive underfeeding on septic and nutrition related morbidity in patients requiring short term parenteral nutrition (PN). This was a single-blinded randomised clinical trial of 50 consecutive patients requiring parenteral nutritional support. Patients were randomized to receive either normocaloric or hypocaloric feeding (respectively 100% vs. 60% of estimated requirements). The primary end point was septic complications. Secondary end points included the metabolic, physiological and clinical outcomes to the two feeding protocols. Permissive underfeeding was associated with fewer septic complications (3 vs. 12 patients; p = 0.003), and a lower incidence of the systemic inflammatory response syndrome (9 vs. 16 patients; p = 0.017). Permissively underfed patients had fewer feed related complications (2 vs. 9 patients; p = 0.016). Permissive underfeeding in patients requiring short term PN appears to be safe and may results in reduced septic and feed-related complications. NCT01154179 TRIAL REGISTRY: http://clinicaltrials.gov/ct2/show/NCT01154179. Copyright © 2014 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Flashing evaporation under different pressure levels

International Nuclear Information System (INIS)

Liao, Yixiang; Lucas, Dirk; Krepper, Eckhard; Rzehak, Roland

2013-01-01

Highlights: • CFD simulation based on two-fluid model for flashing boiling inside a vertical pipe. • Effect of pressure level on the maximum thermal energy available for evaporation. • Effect of presumed bubble size on the onset of flashing as well as evaporation rate. • Effect of pressure level on the critical bubble size that can start stable flashing. • Effect of pressure level on nucleation rate and mechanism. - Abstract: Flashing evaporation of water inside a vertical pipe under four pressure levels is investigated both experimentally and numerically. In the experiment depressurization is realized through a blow-off valve, and the evaporation rate is controlled by the opening rate and degree of the valve. In the CFD simulation phase change is assumed to be caused by thermal heat transfer between steam–water interface and the surrounding water. Consequently, the evaporation rate is determined by heat transfer coefficient, interfacial area density as well as liquid superheat degree. The simulated temporal course of cross-section averaged steam volume fraction is compared with the measured one. It is found that the increasing rate and maximum value of steam volume fraction is over-predicted under low-pressure conditions, which is mainly caused by the neglect of bubble growth in the mono-dispersed simulation. The agreement is notably improved by performing poly-dispersed simulations with the inhomogeneous MUSIG approach (IMUSIG). On the other hand an underestimation of the maximum steam volume fraction is observed in high-pressure cases, since the contribution of nucleation to the total steam generation rate becomes large as the system pressure increases. Reliable models for nucleation rate as well as bubble detachment size are indispensable for reliable predictions. An effect of the system pressure level on the nucleation mechanism is observed in the experiment

WifiLeaks: Underestimated Privacy Implications of the ACCESS_WIFI_STATE Android Permission

OpenAIRE

Achara , Jagdish Prasad; Cunche , Mathieu; Roca , Vincent; Francillon , Aurélien

2014-01-01

A short version has been accepted for publication in: 7th ACM Conference on Security and Privacy in Wireless and Mobile Networks (WISEC'14) Oxford, United Kingdom, July 23rd -- 25th 2014; On Android, users can choose to install an application, or not, based on the permissions it requests. These permissions are later enforced on the application by the system, e.g., when accessing sensitive user data. In this work, we focus on the access to Wi-Fi related information, which is protected by the A...

Effects of lung protective mechanical ventilation associated with permissive respiratory acidosis on regional extra-pulmonary blood flow in experimental ARDS.

Science.gov (United States)

Hering, Rudolf; Kreyer, Stefan; Putensen, Christian

2017-10-27

Lung protective mechanical ventilation with limited peak inspiratory pressure has been shown to affect cardiac output in patients with ARDS. However, little is known about the impact of lung protective mechanical ventilation on regional perfusion, especially when associated with moderate permissive respiratory acidosis. We hypothesized that lung protective mechanical ventilation with limited peak inspiratory pressure and moderate respiratory acidosis results in an increased cardiac output but unequal distribution of blood flow to the different organs of pigs with oleic-acid induced ARDS. Twelve pigs were enrolled, 3 died during instrumentation and induction of lung injury. Thus, 9 animals received pressure controlled mechanical ventilation with a PEEP of 5 cmH 2 O and limited peak inspiratory pressure (17 ± 4 cmH 2 O) versus increased peak inspiratory pressure (23 ± 6 cmH 2 O) in a crossover-randomized design and were analyzed. The sequence of limited versus increased peak inspiratory pressure was randomized using sealed envelopes. Systemic and regional hemodynamics were determined by double indicator dilution technique and colored microspheres, respectively. The paired student t-test and the Wilcoxon test were used to compare normally and not normally distributed data, respectively. Mechanical ventilation with limited inspiratory pressure resulted in moderate hypercapnia and respiratory acidosis (PaCO 2 71 ± 12 vs. 46 ± 9 mmHg, and pH 7.27 ± 0.05 vs. 7.38 ± 0.04, p respiratory acidosis was associated with an increase in cardiac output. However, the better systemic blood flow was not uniformly directed to the different organs. This observation may be of clinical interest in patients, e.g. with cardiac, renal and cerebral pathologies.

A permissive graphical patcher for supercollider synths

OpenAIRE

Dufeu, Frédéric

2016-01-01

This article presents the first version of a permissive graphical patcher (referred to in the text as SCPGP) dedicated to fluid interconnection and control of SuperCollider Synths. With SCPGP, the user programs her/his SynthDefs normally as code in the SuperCollider environment, along with a minimal amount of additional information on these SynthDefs, and programs Patterns according to a simple SuperCollider-compliant syntax.\\ud From the execution of this SuperCollider session, the SCPGP inte...

Verification of Snapshotable Trees using Access Permissions and Typestate

DEFF Research Database (Denmark)

Mehnert, Hannes; Aldrich, Jonathan

2012-01-01

We use access permissions and typestate to specify and ver- ify a Java library that implements snapshotable search trees, as well as some client code. We formalize our approach in the Plural tool, a sound modular typestate checking tool. We describe the challenges to verify- ing snapshotable tree...

Stress and Negative Relationship Quality among Older Couples: Implications for Blood Pressure.

Science.gov (United States)

Birditt, Kira S; Newton, Nicky J; Cranford, James A; Ryan, Lindsay H

2016-09-01

The cardiovascular system may represent a significant pathway by which marriage and stress influence health, but research has focused on married individuals cross-sectionally. This study examined associations among chronic stress, negative spousal relationship quality, and systolic blood pressure over time among middle-aged and older husbands and wives. Participants were from the nationally representative longitudinal Health and Retirement Study. A total of 1,356 (N = 2,712) married and cohabitating couples completed psychosocial and biomeasure assessments in waves 2006 and 2010. Analyses examined whether Wave 1 (2006) relationship quality and stress were associated with changes in blood pressure over time. The effects of stress and negative relationship quality were dyadic and varied by gender. Husbands had increased blood pressure when wives reported greater stress, and this link was exacerbated by negative spousal relationship quality. Negative relationship quality predicted increased blood pressure when both members of the couple reported negative quality relations. Findings support the dyadic biopsychosocial model of marriage and health indicating: (a) stress and relationship quality directly effect the cardiovascular system, (b) relationship quality moderates the effect of stress, and (c) the dyad rather than only the individual should be considered when examining marriage and health. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Determining permissible PT parameters in normal operating conditions for reactor pressure vessel of units 1-4 of NPP Kozloduy

International Nuclear Information System (INIS)

Batischev, M.; Yurukov, V.; Simovski, Ts.

2000-01-01

The main objective of the analysis is to verify the determined from the Main Designer P-T curves and to provide that permissible T values can be decreased even in case a lot of very conservative assumptions are taken into account. Detailed temperature and stress distributions are obtained using different 3D Finite Element Models. Then, assuming linear elastic behaviour and using these distributions onto models including cracks K I values are determined. From the K I values taking into account material characteristics and actual and prognostic neutron fluence of the most sensitive areas of the RPV, P-T curves are determined. Residual stresses in welds are also taken into account. Analysis has been performed independently following two different methodologies - one prescribed by Russian norms (PNAEh-G-7-002-86) and another, developed by the IAEA - 'Guidelines on PTS analysis for WWER NPP'. The obtained results using two methodologies are compared and the more severe are determined

Left-turn phase: permissive, protected, or both? A quasi-experimental design in New York City.

Science.gov (United States)

Chen, Li; Chen, Cynthia; Ewing, Reid

2015-03-01

The practice of left-turn phasing selection (permissive, protected-only, or both) varies from one locality to another. The literature evidence on this issue is equally mixed and insufficient. In this study, we evaluate the safety impacts of changing left-turn signal phasing from permissive to protected/permissive or protected-only at 68 intersections in New York City using a rigorous quasi-experimental design accompanied with regression modeling. Changes in police reported crashes including total crashes, multiple-vehicle crashes, left-turn crashes, pedestrian crashes and bicyclist crashes were compared between before period and after period for the treatment group and comparison group by means of negative binomial regression using a Generalized Estimating Equations (GEE) technique. Confounding factors such as the built environment characteristics that were not controlled in comparison group selection are accounted for by this approach. The results show that the change of permissive left-turn signal phasing to protected/permissive or protected-only signal phasing does not result in a significant reduction in intersection crashes. Though the protected-only signal phasing does reduce the left-turn crashes and pedestrian crashes, this reduction was offset by a possible increase in over-taking crashes. These results suggest that left-turn phasing should not be treated as a universal solution that is always better than the permissive control for left-turn vehicles. The selection and implementation of left-turn signal phasing needs to be done carefully, considering potential trade-offs between safety and delay, and many other factors such as geometry, traffic flows and operations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Mechanics and applications of pressure adaptive honeycomb

Science.gov (United States)

Vos, Roelof

decrease with altitude. This option does require more infrastructure like tubing, valves, and supporting electronics from the cockpit. Applications of pressure adaptive honeycomb are tailored primarily towards low-bandwidth applications like secondary flight control. The most profound application is the morphing of an entire wing section, from leading to trailing edge, due to the adaptive honeycomb. On a smaller scale, other examples include a solid state pressure adaptive flap, a pressure adaptive droop nose, a pressure adaptive Gurney flap and a pressure adaptive engine inlet. Each of these applications is based on the same principle of stiffness alteration with pressure and can be used with either actuation option (constant mass or constant pressure). A model that relates the volumetric change of the honeycomb cells to the external blocked stress was shown to correlate well to experiments that were carried out on several test articles. Based on this model it was estimated that pressure adaptive honeycomb has a maximum mass-specific energy density of 12.4J/g, for the case of an externally applied CDP of 0.9MPa (can be supplied from a high-pressure compressor stage of a gas turbine). In addition, it was shown that a maximum strain of 76% can be achieved and that the maximum blocked stress amounts to 0.82MPa. In the case of a 40kPa drop in atmospheric pressure and constant mass of air in the pouches, the maximum mass specific energy amounts to 1.1J/g and a maximum blocked force of 70kPa can be attained. Pressure adaptive honeycomb was embedded into a 25%c adaptive flap on a NACA2412 wing section with a chord of 1.08m. Wind tunnel tests at Reynolds number of 1 million demonstrated a shift in the cl -- alpha curve upwards by an average of 0.3, thereby increasing the maximum lift coefficient from 1.27 to 1.52. This successfully demonstrated the application of pressure adaptive honeycomb embedded in a morphing aircraft structure.

Blood Pressure and Intracranial Aneurysms in Autosomal Dominant Polycystic Kidney Disease

Directory of Open Access Journals (Sweden)

Mariusz Niemczyk

2014-12-01

Full Text Available Background/Aims: Autosomal dominant polycystic kidney disease (ADPKD is correlated with an increased frequency of both intracranial aneurysms (ICANs, and arterial hypertension (AH. The aim of our study was to search for the association between blood pressure (BP and ICANs in ADPKD patients. Methods: Sixty-eight adult, pre-dialysis phase ADPKD patients underwent both screening for ICANs with magnetic resonance angiography of the brain, and ambulatory blood pressure monitoring (ABPM. Results: ICANs were diagnosed in 10 patients (ICAN(+ group, while in 58 were not (ICAN(- group. The nighttime maximum diastolic blood pressure (DBP, maximum increase in DBP from measurement to measurement (positive delta of DBP at night, and the standard deviation of the daytime mean arterial pressure were significantly higher in ICAN(+ compared to ICAN(- patients. Additionally, in a subgroup of patients after 45 years-of-age, ICAN(+ patients had significantly higher maximum 24-hour and daytime systolic blood pressure, maximum 24-hour, daytime, nighttime DBP, maximum daytime and nighttime positive delta of DBP compared to ICAN(- cases. Conclusions: Development of ICANs in hypertensive ADPKD patients is accompanied with higher values of some BP parameters measured by ABPM. Hypertensive ADPKD patients with substantial fluctuations in BP assessed by ABPM, especially those after 45 years-of-age, should become candidates for screening for ICANs.

Determination of permissible doses under the provisions of the regulations on installation and operation of reactors for power generation

International Nuclear Information System (INIS)

1979-01-01

The determination is defined under the regulations on installation and operation of reactors for power generation. In the controlled area exterior radiation dose shall be 30 mili-rem for a week by the Minister of International Trade and Industry. The concentrations of radioactive materials in the air or under the water shall be permissible concentrations specified for the employees multiplied by 0.75 in average for a week. The densities of radioactive materials on the surface of the things contaminated by such materials shall be 1/10 of permissible surface densities stipulated in the table attached. Permissible exposure dose outside the inspected surrounding area is 0.5 rem for a year. Permissible surface densities are included in the table attached. Permissible accumulative dose for the employees is the figure (unit rem) calculated by the formula D = 5(N-18), when D means permissible accumulative dose and N number of the age. Permissible exposure dose is 3 rem for 3 months for the employees, 1.5 rem for a year for persons other than the employees and 12 rem for the urgent work. Permissible concentrations are defined in detail for the employees and outside the inspected surrounding area. Calculation of exposure dose in the case of interior exposure is particularly provided for. (Okada, K.)

Corruption and the Other(s): Scope of Superordinate Identity Matters for Corruption Permissibility.

Science.gov (United States)

Pisor, Anne C; Gurven, Michael

2015-01-01

The decision to engage in corruption-public and private corruption, nepotism, and embezzlement-is often attributed to rational actors maximizing benefits to themselves. However, the importance of reciprocal relationships in humans suggests that an actor may weigh the costs of harms of her corrupt behavior to individuals who may generate future benefits for her. We hypothesize that actors who have a larger circle of actual and potential social partners will have more individuals to consider when generating harms and will thus be less likely to find corrupt acts permissible than actors with smaller circles of valued others. Using data from the World Values Survey and European Values Study (WVS), we explore whether participants with a larger geographic identity or a greater number of group memberships (i.e. a larger scope of actual and potential social partners) are less likely to find accepting bribes permissible. We find mixed support for our hypotheses, but consistently find that WVS participants with local, country, continent, or world geographic identities are less likely to find accepting a bribe permissible than those with regional identities-that is, actors whose primary identities that encompass more than their region find corruption less permissible. We discuss the importance of considering an actor's valuation of others when modeling corruption persistence, noting that establishing scopes of positive valuation is a precursor to predicting where actors will target benefits and shunt costs.

Fracture mechanics analysis of reactor pressure vessel under pressurized thermal shock - The effect of elastic-plastic behavior and stainless steel cladding -

International Nuclear Information System (INIS)

Joo, Jae Hwang; Kang, Ki Ju; Jhung, Myung Jo

2002-01-01

Performed here is an assessment study for deterministic fracture mechanics analysis of a pressurized thermal shock (PTS). The PTS event means an event or transient in pressurized water reactors (PWRs) causing severe overcooling (thermal shock) concurrent with or followed by significant pressure in the reactor vessel. The problems consisting of two transients and 10 cracks are solved and maximum stress intensity factors and maximum allowable nil-ductility reference temperatures are calculated. Their results are compared each other to address the general characteristics between transients, crack types and analysis methods. The effects of elastic-plastic material behavior and clad coating on the inner surface are explored

Firefighter's compressed air breathing system pressure vessel development program

Science.gov (United States)

Beck, E. J.

1974-01-01

The research to design, fabricate, test, and deliver a pressure vessel for the main component in an improved high-performance firefighter's breathing system is reported. The principal physical and performance characteristics of the vessel which were required are: (1) maximum weight of 9.0 lb; (2) maximum operating pressure of 4500 psig (charge pressure of 4000 psig); (3) minimum contained volume of 280 in. 3; (4) proof pressure of 6750 psig; (5) minimum burst pressure of 9000 psig following operational and service life; and (6) a minimum service life of 15 years. The vessel developed to fulfill the requirements described was completely sucessful, i.e., every category of performence was satisfied. The average weight of the vessel was found to be about 8.3 lb, well below the 9.0 lb specification requirement.

Water Pressure Distribution on a Twin-Float Seaplane

Science.gov (United States)

Thompson, F L

1930-01-01

This is the second of a series of investigations to determine water pressure distribution on various types of seaplane floats and hulls, and was conducted on a twin-float seaplane. It consisted of measuring water pressures and accelerations on a TS-1 seaplane during numerous landing and taxiing maneuvers at various speeds and angles. The results show that water pressures as great as 10 lbs. per sq. in.may occur at the step in various maneuvers and that pressures of approximately the same magnitude occur at the stern and near the bow in hard pancake landings with the stern way down. At the other parts of the float the pressures are less and are usually zero or slightly negative for some distance abaft the step. A maximum negative pressure of 0.87 lb. Per square inch was measured immediately abaft the step. The maximum positive pressures have a duration of approximately one-twentieth to one-hundredth second at any given location and are distributed over a very limited area at any particular instant.

Recommendation of maximum allowable noise levels for offshore wind power systems; Empfehlung von Laermschutzwerten bei der Errichtung von Offshore-Windenergieanlagen (OWEA)

Energy Technology Data Exchange (ETDEWEB)

Werner, Stefanie [Umweltbundesamt, Dessau-Rosslau (Germany). Fachgebiet II 2.3

2011-05-15

When offshore wind farms are constructed, every single pile is hammered into the sediment by a hydraulic hammer. Noise levels at Horns Reef wind farm were in the range of 235 dB. The noise may cause damage to the auditory system of marine mammals. The Federal Environmental Office therefore recommends the definition of maximum permissible noise levels. Further, care should be taken that no marine mammals are found in the immediate vicinity of the construction site. (AKB)

Reducing the incidence of pressure ulcers in critical care units: a 4-year quality improvement.

Science.gov (United States)

Richardson, Annette; Peart, Joanna; Wright, Stephen E; McCullagh, Iain J

2017-06-01

Critical care patients often have several risk factors for pressure ulceration and implementing prevention interventions have been shown to decrease risk. We identified a high incidence of pressure ulcers in the four adult critical care units in our organization. Therefore, avoiding pressure ulceration was an important quality priority. We undertook a quality improvement programme aimed at reducing the incidence of pressure ulceration using an evidence-based bundle approach. A bundle of technical and non-technical interventions were implemented supported by clinical leadership on each unit. Important components were evidence appraisals; changes to mattresses; focussed risk assessment alongside mandating patients at very high risk to be repositioned two hourly; and staff training to increase awareness of how to prevent pressure ulcers. Pressure ulcer numbers, incidence and categories were collected continuously and monitored monthly by unit staff. Pressure ulcer rates reduced significantly from 8.08/100 patient admissions to 2.97/100 patient admissions, an overall relative rate reduction of 63% over 4 years. The greatest reduction was seen in the most severe category of pressure ulceration. The average estimated cost saving was £2.6 million (range £2.1-£3.1). A quality improvement programme including technical and non-technical interventions, data feedback to staff and clinical leadership was associated with a sustained reduction in the incidence of pressure ulceration in the critically ill. Strategies used in this programme may be transferable to other critical care units to bring more widespread patient benefit. © The Author 2017. Published by Oxford University Press in association with the International Society for Quality in Health Care. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Chemical vapor deposition of hexagonal boron nitride films in the reduced pressure

International Nuclear Information System (INIS)

Choi, B.J.

1999-01-01

Hexagonal boron nitride (h-BN) films were deposited onto a graphite substrate in reduced pressure by reacting ammonia and boron tribromide at 800--1,200 C. The growth rate of h-BN films was dependent on the substrate temperature and the total pressures. The growth rate increased with increasing the substrate temperature at the pressure of 2 kPa, while it showed a maximum value at the pressures of 4 and 8 kPa. The temperature at which the maximum growth rate occurs decreased with increasing total pressure. With increasing the substrate temperature and total pressure, the apparent grain size increased and the surface morphology showed a rough, cauliflower-like structure

Measuring bacterial activity and community composition at high hydrostatic pressure using a novel experimental approach: a pilot study.

Science.gov (United States)

Wannicke, Nicola; Frindte, Katharina; Gust, Giselher; Liskow, Iris; Wacker, Alexander; Meyer, Andreas; Grossart, Hans-Peter

2015-05-01

In this pilot study, we describe a high-pressure incubation system allowing multiple subsampling of a pressurized culture without decompression. The system was tested using one piezophilic (Photobacterium profundum), one piezotolerant (Colwellia maris) bacterial strain and a decompressed sample from the Mediterranean deep sea (3044 m) determining bacterial community composition, protein production (BPP) and cell multiplication rates (BCM) up to 27 MPa. The results showed elevation of BPP at high pressure was by a factor of 1.5 ± 1.4 and 3.9 ± 2.3 for P. profundum and C. maris, respectively, compared to ambient-pressure treatments and by a factor of 6.9 ± 3.8 fold in the field samples. In P. profundum and C. maris, BCM at high pressure was elevated (3.1 ± 1.5 and 2.9 ± 1.7 fold, respectively) compared to the ambient-pressure treatments. After 3 days of incubation at 27 MPa, the natural bacterial deep-sea community was dominated by one phylum of the genus Exiguobacterium, indicating the rapid selection of piezotolerant bacteria. In future studies, our novel incubation system could be part of an isopiestic pressure chain, allowing more accurate measurement of bacterial activity rates which is important both for modeling and for predicting the efficiency of the oceanic carbon pump. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

29 CFR 3.6 - Payroll deductions permissible with the approval of the Secretary of Labor.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Payroll deductions permissible with the approval of the Secretary of Labor. 3.6 Section 3.6 Labor Office of the Secretary of Labor CONTRACTORS AND SUBCONTRACTORS ON....6 Payroll deductions permissible with the approval of the Secretary of Labor. Any contractor or...

Android Apps and Permissions: Security and Privacy Risks

OpenAIRE

Boksasp, Trond; Utnes, Eivind

2012-01-01

This thesis investigates the permissions requested by Android applications, and the possibility of identifying suspicious applications based only on information presented to the user before an application is downloaded. During the course of this project, a large data set consisting of applications published on Google Play and three different third-party Android application markets was collected over a two-month period. These applications are analysed using manual pattern recognition and k-mea...

Sexual and Gender Minority Adolescents' Views On HIV Research Participation and Parental Permission: A Mixed-Methods Study.

Science.gov (United States)

Mustanski, Brian; Coventry, Ryan; Macapagal, Kathryn; Arbeit, Miriam R; Fisher, Celia B

2017-06-01

Sexual and gender minority adolescents are underrepresented in HIV research, partly because institutional review boards (IRBs) are reluctant to waive parental permission requirements for these studies. Understanding teenagers' perspectives on parental permission and the risks and benefits of participating in HIV research is critical to informing evidence-based IRB decisions. Data from 74 sexual and gender minority adolescents aged 14-17 who participated in an online focus group in 2015 were used to examine perspectives on the risks and benefits of participation in a hypothetical HIV surveillance study and the need for parental permission and adequate protections. Data were analyzed thematically; mixed methods analyses examined whether concerns about parental permission differed by whether teenagers were out to their parents. Most adolescents, especially those who were not out to their parents, would be unwilling to participate in an HIV study if parental permission were required. Perceived benefits of participation included overcoming barriers to HIV testing and contributing to the health of sexual and gender minority youth. Few risks of participation were identified. Adolescents suggested steps that researchers could take to facilitate informed decision making about research participation and ensure minors' safety in the absence of parental permission; these included incorporating multimedia presentations into the consent process and explaining researchers' motivations for conducting the study. Respondents believed that the benefits of HIV surveillance research outweighed the risks. Requiring parental permission may exclude many sexual and gender minority teenagers from taking part in HIV research, especially if they are not out. Copyright © 2017 by the Guttmacher Institute.

Influence of geomagnetic activity and atmospheric pressure on human arterial pressure during the solar cycle 24

Science.gov (United States)

Azcárate, T.; Mendoza, B.; Levi, J. R.

2016-11-01

We performed a study of the systolic (SBP) and diastolic (DBP) arterial blood pressure behavior under natural variables such as the atmospheric pressure (AtmP) and the horizontal geomagnetic field component (H). We worked with a sample of 304 healthy normotense volunteers, 152 men and 152 women, with ages between 18 and 84 years in Mexico City during the period 2008-2014, corresponding to the minimum, ascending and maximum phases of the solar cycle 24. The data was divided by gender, age and day/night cycle. We studied the time series using three methods: Correlations, bivariate and superposed epochs (within a window of three days around the day of occurrence of a geomagnetic storm) analysis, between the SBP and DBP and the natural variables (AtmP and H). The correlation analysis indicated correlation between the SBP and DBP and AtmP and H, being the largest during the night. Furthermore, the correlation and bivariate analysis showed that the largest correlations are between the SBP and DBP and the AtmP. The superposed epoch analysis found that the largest number of significant SBP and DBP changes occurred for women. Finally, the blood pressure changes are larger during the solar minimum and ascending solar cycle phases than during the solar maximum; the storms of the minimum were more intense than those of the maximum and this could be the reason of behavior of the blood pressure changes along the solar cycle.

Permissive cytomegalovirus infection of primary villous term and first trimester trophoblasts.

Science.gov (United States)

Hemmings, D G; Kilani, R; Nykiforuk, C; Preiksaitis, J; Guilbert, L J

1998-06-01

Forty percent of women with primary cytomegalovirus (CMV) infections during pregnancy infect their fetuses with complications for the baby varying from mild to severe. How CMV crosses the syncytiotrophoblast, the barrier between maternal blood and fetal tissue in the villous placenta, is unknown. Virus may cross by infection of maternal cells that pass through physical breaches in the syncytiotrophoblast or by direct infection of the syncytiotrophoblast, with subsequent transmission to underlying fetal placental cells. In this study, we show that pure (>99.99%), long-term and healthy (>3 weeks) cultures of syncytiotrophoblasts are permissively infected with CMV. Greater than 99% of infectious progeny virus remained cell associated throughout culture periods up to 3 weeks. Infection of term trophoblasts required a higher virus inoculum, was less efficient, and progressed more slowly than parallel infections of placental and human embryonic lung fibroblasts. Three laboratory strains (AD169, Towne, and Davis) and a clinical isolate from a congenitally infected infant all permissively infected trophoblasts, although infection efficiencies varied. The infection of first trimester syncytiotrophoblasts with strain AD169 occurred at higher frequency and progressed more rapidly than infection of term cells but less efficiently and rapidly than infection of fibroblasts. These results show that villous syncytiotrophoblasts can be permissively infected by CMV but that the infection requires high virus titers and proceeds slowly and that progeny virus remains predominantly cell associated.

Physical understanding of the tropical cyclone wind-pressure relationship.

Science.gov (United States)

Chavas, Daniel R; Reed, Kevin A; Knaff, John A

2017-11-08

The relationship between the two common measures of tropical cyclone intensity, the central pressure deficit and the peak near-surface wind speed, is a long-standing problem in tropical meteorology that has been approximated empirically yet lacks physical understanding. Here we provide theoretical grounding for this relationship. We first demonstrate that the central pressure deficit is highly predictable from the low-level wind field via gradient wind balance. We then show that this relationship reduces to a dependence on two velocity scales: the maximum azimuthal-mean azimuthal wind speed and half the product of the Coriolis parameter and outer storm size. This simple theory is found to hold across a hierarchy of models spanning reduced-complexity and Earth-like global simulations and observations. Thus, the central pressure deficit is an intensity measure that combines maximum wind speed, storm size, and background rotation rate. This work has significant implications for both fundamental understanding and risk analysis, including why the central pressure better explains historical economic damages than does maximum wind speed.

Corruption and the Other(s: Scope of Superordinate Identity Matters for Corruption Permissibility.

Directory of Open Access Journals (Sweden)

Anne C Pisor

Full Text Available The decision to engage in corruption-public and private corruption, nepotism, and embezzlement-is often attributed to rational actors maximizing benefits to themselves. However, the importance of reciprocal relationships in humans suggests that an actor may weigh the costs of harms of her corrupt behavior to individuals who may generate future benefits for her. We hypothesize that actors who have a larger circle of actual and potential social partners will have more individuals to consider when generating harms and will thus be less likely to find corrupt acts permissible than actors with smaller circles of valued others. Using data from the World Values Survey and European Values Study (WVS, we explore whether participants with a larger geographic identity or a greater number of group memberships (i.e. a larger scope of actual and potential social partners are less likely to find accepting bribes permissible. We find mixed support for our hypotheses, but consistently find that WVS participants with local, country, continent, or world geographic identities are less likely to find accepting a bribe permissible than those with regional identities-that is, actors whose primary identities that encompass more than their region find corruption less permissible. We discuss the importance of considering an actor's valuation of others when modeling corruption persistence, noting that establishing scopes of positive valuation is a precursor to predicting where actors will target benefits and shunt costs.

Perceived realism moderates the relation between sexualized media consumption and permissive sexual attitudes in Dutch adolescents.

Science.gov (United States)

Baams, Laura; Overbeek, Geertjan; Dubas, Judith Semon; Doornwaard, Suzan M; Rommes, Els; van Aken, Marcel A G

2015-04-01

This study examined whether the development of sexualized media consumption and permissive sexual attitudes would be more strongly interrelated when adolescents perceived sexualized media images as highly realistic. We used data from a three-wave longitudinal sample of 444 Dutch adolescents aged 13-16 years at baseline. Results from parallel process latent growth modeling multigroup analyses showed that higher initial levels of sexualized media consumption were associated with higher initial level of permissive sexual attitudes. Moreover, increases of sexualized media consumption over time were associated with increases of permissive sexual attitudes over time. Considering the moderation by perceived realism, we found these effects only for those who perceived sexualized media as more realistic. Findings for male and female adolescents were similar except for the relations between initial levels and subsequent development. Among male adolescents who perceived sexualized media images to be realistic, higher initial levels of permissive sexual attitudes were related to subsequent less rapid development of sexualized media consumption. For male adolescents who perceived sexualized media to be less realistic, higher initial levels of sexualized media consumption were related to a subsequent less rapid development of permissive sexual attitudes. These relations were not found for female adolescents. Overall, our results suggest that, in male and female adolescents, those with a high level of perceived realism showed a correlated development of sexualized media consumption and permissive sexual attitudes. These findings point to a need for extended information on how to guide adolescents in interpreting and handling sexualized media in everyday life.

Gender Differences in Adolescent Premarital Sexual Permissiveness in Three Asian Cities: Effects of Gender-Role Attitudes

Science.gov (United States)

Xiayun, Zuo; Chaohua, Lou; Ersheng, Gao; Yan, Cheng; Hongfeng, Niu; Zabin, Laurie S.

2014-01-01

Purpose Gender is an important factor in understanding premarital sexual attitudes and behaviors. Many studies indicate that males are more likely to initiate sexual intercourse and have more permissive perceptions about sex than females. Yet few studies have explored possible reasons for these gender differences. With samples of unmarried adolescents in three Asian cities influenced by Confucian cultures, this paper investigates the relationship between underlying gender norms and these differences in adolescents’ premarital sexual permissiveness. Methods 16,554 unmarried participants aged 15–24 were recruited in the Three-City Asian Study of Adolescents and Youth, a collaborative survey conducted in 2006–2007 in urban and rural areas of Hanoi, Shanghai and Taipei, with 6204, 6023 and 4327 from each city respectively. All of the adolescents were administered face-to-face interviews, coupled with Computer Assisted Self Interview (CASI) for sensitive questions. Scales on gender-role attitudes and on premarital sexual permissiveness for both male and female respondents were developed and applied to our analysis of the data. Multi-linear regression was used to analyze the relationship between gender-role attitudes and sexual permissiveness. Results Male respondents in each city held more permissive attitudes towards premarital sex than did females with both boys and girls expressing greater permissiveness to male premarital sexual behaviors. Boys also expressed more traditional attitudes to gender roles (condoning greater inequality) than did girls in each city. Adolescents’ gender-role attitudes and permissiveness to premarital sex varied considerably across the three cities, with the Vietnamese the most traditional, the Taiwanese the least traditional, and the adolescents in Shanghai in the middle. A negative association between traditional gender roles and premarital sexual permissiveness was only found among girls in Shanghai and Taipei. In Shanghai

A Rational Threshold Signature Model and Protocol Based on Different Permissions

Directory of Open Access Journals (Sweden)

Bojun Wang

2014-01-01

Full Text Available This paper develops a novel model and protocol used in some specific scenarios, in which the participants of multiple groups with different permissions can finish the signature together. We apply the secret sharing scheme based on difference equation to the private key distribution phase and secret reconstruction phrase of our threshold signature scheme. In addition, our scheme can achieve the signature success because of the punishment strategy of the repeated rational secret sharing. Besides, the bit commitment and verification method used to detect players’ cheating behavior acts as a contributing factor to prevent the internal fraud. Using bit commitments, verifiable parameters, and time sequences, this paper constructs a dynamic game model, which has the features of threshold signature management with different permissions, cheat proof, and forward security.

Pressure relief experiments on a cyclindrical carbon brick tube

International Nuclear Information System (INIS)

Lang, H.; Weise, H.J.; Ennen, P.

1978-08-01

Pressure relief experiments have been carried out on a carbon brick tube. The outer diameter of the specimen was 580 mm, the inner diameter 280 mm, the length 800 mm. The experiments were made with helium at the temperature of the environment. The measurements were carried out in the pressure range from 15 upto 39 bar. The pressure loss was measured dependent on the initial pressure and on time at 5 positions uniformly distributed over the thickness of the tube wall and in the pressure vessel. The maximum pressure transients occurred amounted to approximately 60 bar/second. The maximum overpressure with respect to the environment which occurred in the carbon brick during the relief experiments was about 3.3 bar. The measurements distinctly showed the presence and the effects of inhomogeneities in the sample material. No damages or changes in the carbon brick, which could be regarded as a consequence of the experiments, were found. (orig./GSC) [de

Pressurized subsampling system for pressured gas-hydrate-bearing sediment: Microscale imaging using X-ray computed tomography

International Nuclear Information System (INIS)

Jin, Yusuke; Konno, Yoshihiro; Nagao, Jiro

2014-01-01

A pressurized subsampling system was developed for pressured gas hydrate (GH)-bearing sediments, which have been stored under pressure. The system subsamples small amounts of GH sediments from cores (approximately 50 mm in diameter and 300 mm in height) without pressure release to atmospheric conditions. The maximum size of the subsamples is 12.5 mm in diameter and 20 mm in height. Moreover, our system transfers the subsample into a pressure vessel, and seals the pressure vessel by screwing in a plug under hydraulic pressure conditions. In this study, we demonstrated pressurized subsampling from artificial xenon-hydrate sediments and nondestructive microscale imaging of the subsample, using a microfocus X-ray computed tomography (CT) system. In addition, we estimated porosity and hydrate saturation from two-dimensional X-ray CT images of the subsamples

11 CFR 114.15 - Permissible use of corporate and labor organization funds for certain electioneering communications.

Science.gov (United States)

2010-01-01

... 11 Federal Elections 1 2010-01-01 2010-01-01 false Permissible use of corporate and labor organization funds for certain electioneering communications. 114.15 Section 114.15 Federal Elections FEDERAL ELECTION COMMISSION GENERAL CORPORATE AND LABOR ORGANIZATION ACTIVITY § 114.15 Permissible use of corporate...

Relationship between medical compression and intramuscular pressure as an explanation of a compression paradox.

Science.gov (United States)

Uhl, J-F; Benigni, J-P; Cornu-Thenard, A; Fournier, J; Blin, E

2015-06-01

Using standing magnetic resonance imaging (MRI), we recently showed that medical compression, providing an interface pressure (IP) of 22 mmHg, significantly compressed the deep veins of the leg but not, paradoxically, superficial varicose veins. To provide an explanation for this compression paradox by studying the correlation between the IP exerted by medical compression and intramuscular pressure (IMP). In 10 legs of five healthy subjects, we studied the effects of different IPs on the IMP of the medial gastrocnemius muscle. The IP produced by a cuff manometer was verified by a Picopress® device. The IMP was measured with a 21G needle connected to a manometer. Pressure data were recorded in the prone and standing positions with cuff manometer pressures from 0 to 50 mmHg. In the prone position, an IP of less than 20 did not significantly change the IMP. On the contrary, a perfect linear correlation with the IMP (r = 0.99) was observed with an IP from 20 to 50 mmHg. We found the same correlation in the standing position. We found that an IP of 22 mmHg produced a significant IMP increase from 32 to 54 mmHg, in the standing position. At the same time, the subcutaneous pressure is only provided by the compression device, on healthy subjects. In other words, the subcutaneous pressure plus the IP is only a little higher than 22 mmHg-a pressure which is too low to reduce the caliber of the superficial veins. This is in accordance with our standing MRI 3D anatomical study which showed that, paradoxically, when applying low pressures (IP), the deep veins are compressed while the superficial veins are not. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Challenges to obtaining parental permission for child participation in a school-based waterpipe tobacco smoking prevention intervention in Qatar.

Science.gov (United States)

Nakkash, Rima T; Al Mulla, Ahmad; Torossian, Lena; Karhily, Roubina; Shuayb, Lama; Mahfoud, Ziyad R; Janahi, Ibrahim; Al Ansari, Al Anoud; Afifi, Rema A

2014-09-30

Involving children in research studies requires obtaining parental permission. A school-based intervention to delay/prevent waterpipe use for 7th and 8th graders in Qatar was developed, and parental permission requested. Fifty three percent (2308/4314) of the parents returned permission forms; of those 19.5% of the total (840/4314) granted permission. This paper describes the challenges to obtaining parental permission. No research to date has described such challenges in the Arab world. A random sample of 40 schools in Doha, Qatar was selected for inclusion in the original intervention. Permission forms were distributed to parents for approval of their child's participation. The permission forms requested that parents indicate their reasons for non-permission if they declined. These were categorized into themes. In order to understand reasons for non-permission, interviews with parents were conducted. Phone numbers of parents were requested from the school administration; 12 of the 40 schools (30%) agreed to provide the contact information. A random sample of 28 parents from 12 schools was interviewed to reach data saturation. Thematic analysis was used to analyze their responses. Reasons for non-permission documented in both the forms and interviews included: poor timing; lack of interest; the child not wanting to participate; and the child living in a smoke-free environment. Interviews provided information on important topics to include in the consent forms, parents' decision-making processes regarding their child's participation, and considerations for communicating with parents. Many parents also indicated that this was the first time they had been asked to give an informed consent for their child's participation in a study. Results indicate that more attention needs to be given to the informed parental consent process. Researchers should consider enhancing both the methods of communicating information as well the specific information provided. Before

12 CFR 714.2 - What are the permissible leasing arrangements?

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false What are the permissible leasing arrangements? 714.2 Section 714.2 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING... leasing. In direct leasing, you purchase personal property from a vendor, becoming the owner of the...

THE GENERALIZED MAXIMUM LIKELIHOOD METHOD APPLIED TO HIGH PRESSURE PHASE EQUILIBRIUM

Directory of Open Access Journals (Sweden)

Lúcio CARDOZO-FILHO

1997-12-01

Full Text Available The generalized maximum likelihood method was used to determine binary interaction parameters between carbon dioxide and components of orange essential oil. Vapor-liquid equilibrium was modeled with Peng-Robinson and Soave-Redlich-Kwong equations, using a methodology proposed in 1979 by Asselineau, Bogdanic and Vidal. Experimental vapor-liquid equilibrium data on binary mixtures formed with carbon dioxide and compounds usually found in orange essential oil were used to test the model. These systems were chosen to demonstrate that the maximum likelihood method produces binary interaction parameters for cubic equations of state capable of satisfactorily describing phase equilibrium, even for a binary such as ethanol/CO2. Results corroborate that the Peng-Robinson, as well as the Soave-Redlich-Kwong, equation can be used to describe phase equilibrium for the following systems: components of essential oil of orange/CO2.Foi empregado o método da máxima verossimilhança generalizado para determinação de parâmetros de interação binária entre os componentes do óleo essencial de laranja e dióxido de carbono. Foram usados dados experimentais de equilíbrio líquido-vapor de misturas binárias de dióxido de carbono e componentes do óleo essencial de laranja. O equilíbrio líquido-vapor foi modelado com as equações de Peng-Robinson e de Soave-Redlich-Kwong usando a metodologia proposta em 1979 por Asselineau, Bogdanic e Vidal. A escolha destes sistemas teve como objetivo demonstrar que o método da máxima verosimilhança produz parâmetros de interação binária, para equações cúbicas de estado capazes de descrever satisfatoriamente até mesmo o equilíbrio para o binário etanol/CO2. Os resultados comprovam que tanto a equação de Peng-Robinson quanto a de Soave-Redlich-Kwong podem ser empregadas para descrever o equilíbrio de fases para o sistemas: componentes do óleo essencial de laranja/CO2.

Effects of pressurization procedures on calibration results for precise pressure transducers

International Nuclear Information System (INIS)

Kajikawa, Hiroaki; Kobata, Tokihiko

2010-01-01

The output of electromechanical pressure gauges depends on not only the currently applied pressure, but also the pressurization history. Thus, the calibration results of gauges are affected by the pressurization procedure. In this paper, among several important factors influencing the results, we report the effects of the interval between the calibration cycles and the effects of the preliminary pressurizations. In order to quantitatively evaluate these effects, we developed a fully automated system that uses a pressure balance to calibrate pressure gauges. Subsequently, gauges containing quartz Bourdon-type pressure transducers were calibrated in a stepwise manner for pressures between 10 MPa and 100 MPa. The typical standard deviation of the data over three cycles was reduced to a few parts per million (ppm). The interval between the calibration cycles, which ranges from zero to more than 12 h, exerts a strong influence on the results in the process of increasing the pressure, where at 10 MPa the maximum difference between the results was approximately 40 ppm. The preliminary pressurization immediately before the calibration cycle reduces the effects of the interval on the results in certain cases. However, in turn, the influence of the waiting time between the preliminary pressurization and the main calibration cycle becomes strong. In the present paper, we outline several possible measures for obtaining calibration results with high reproducibility

Multi-bottle, no compressor, mean pressure control system for a Stirling engine

Science.gov (United States)

Corey, John A.

1990-01-01

The invention relates to an apparatus for mean pressure control of a Stirling engine without the need for a compressor. The invention includes a multi-tank system in which there is at least one high pressure level tank and one low pressure level tank wherein gas flows through a maximum pressure and supply line from the engine to the high pressure tank when a first valve is opened until the maximum pressure of the engine drops below that of the high pressure tank opening an inlet regulator to permit gas flow from the engine to the low pressure tank. When gas flows toward the engine it flows through the minimum pressure supply line 2 when a second valve is opened from the low pressure tank until the tank reaches the engine's minimum pressure level at which time the outlet regulator opens permitting gas to be supplied from the high pressure tank to the engine. Check valves between the two tanks prevent any backflow of gas from occurring.

Analysis of pressurization of plutonium oxide storage vials during a postulated fire

Energy Technology Data Exchange (ETDEWEB)

Laurinat, J.; Kesterson, M.; Hensel, S.

2015-02-10

The documented safety analysis for the Savannah River Site evaluates the consequences of a postulated 1000 °C fire in a glovebox. The radiological dose consequences for a pressurized release of plutonium oxide powder during such a fire depend on the maximum pressure that is attained inside the oxide storage vial. To enable evaluation of the dose consequences, pressure transients and venting flow rates have been calculated for exposure of the storage vial to the fire. A standard B vial with a capacity of approximately 8 cc was selected for analysis. The analysis compares the pressurization rate from heating and evaporation of moisture adsorbed onto the plutonium oxide contents of the vial with the pressure loss due to venting of gas through the threaded connection between the vial cap and body. Tabulated results from the analysis include maximum pressures, maximum venting velocities, and cumulative vial volumes vented during the first 10 minutes of the fire transient. Results are obtained for various amounts of oxide in the vial, various amounts of adsorbed moisture, different vial orientations, and different surface fire exposures.

Combined pressure and cosolvent effects on enzyme activity - a high-pressure stopped-flow kinetic study on α-chymotrypsin.

Science.gov (United States)

Luong, Trung Quan; Winter, Roland

2015-09-21

We investigated the combined effects of cosolvents and pressure on the hydrolysis of a model peptide catalysed by α-chymotrypsin. The enzymatic activity was measured in the pressure range from 0.1 to 200 MPa using a high-pressure stopped-flow systems with 10 ms time resolution. A kosmotropic (trimethalymine-N-oxide, TMAO) and chaotropic (urea) cosolvent and mixtures thereof were used as cosolvents. High pressure enhances the hydrolysis rate as a consequence of a negative activation volume, ΔV(#), which, depending on the cosolvent system, amounts to -2 to -4 mL mol(-1). A more negative activation volume can be explained by a smaller compression of the ES complex relative to the transition state. Kinetic constants, such as kcat and the Michaelis constant KM, were determined for all solution conditions as a function of pressure. With increasing pressure, kcat increases by about 35% and its pressure dependence by a factor of 1.9 upon addition of 2 M urea, whereas 1 M TMAO has no significant effect on kcat and its pressure dependence. Similarly, KM increases upon addition of urea 6-fold. Addition of TMAO compensates the urea-effect on kcat and KM to some extent. The maximum rate of the enzymatic reaction increases with increasing pressure in all solutions except in the TMAO : urea 1 : 2 mixture, where, remarkably, pressure is found to have no effect on the rate of the enzymatic reaction anymore. Our data clearly show that compatible solutes can easily override deleterious effects of harsh environmental conditions, such as high hydrostatic pressures in the 100 MPa range, which is the maximum pressure encountered in the deep biosphere on Earth.

Influence of maximum bite force on jaw movement during gummy jelly mastication.

Science.gov (United States)

Kuninori, T; Tomonari, H; Uehara, S; Kitashima, F; Yagi, T; Miyawaki, S

2014-05-01

It is known that maximum bite force has various influences on chewing function; however, there have not been studies in which the relationships between maximum bite force and masticatory jaw movement have been clarified. The aim of this study was to investigate the effect of maximum bite force on masticatory jaw movement in subjects with normal occlusion. Thirty young adults (22 men and 8 women; mean age, 22.6 years) with good occlusion were divided into two groups based on whether they had a relatively high or low maximum bite force according to the median. The maximum bite force was determined according to the Dental Prescale System using pressure-sensitive sheets. Jaw movement during mastication of hard gummy jelly (each 5.5 g) on the preferred chewing side was recorded using a six degrees of freedom jaw movement recording system. The motion of the lower incisal point of the mandible was computed, and the mean values of 10 cycles (cycles 2-11) were calculated. A masticatory performance test was conducted using gummy jelly. Subjects with a lower maximum bite force showed increased maximum lateral amplitude, closing distance, width and closing angle; wider masticatory jaw movement; and significantly lower masticatory performance. However, no differences in the maximum vertical or maximum anteroposterior amplitudes were observed between the groups. Although other factors, such as individual morphology, may influence masticatory jaw movement, our results suggest that subjects with a lower maximum bite force show increased lateral jaw motion during mastication. © 2014 John Wiley & Sons Ltd.

What controls the maximum magnitude of injection-induced earthquakes?

Science.gov (United States)

Eaton, D. W. S.

2017-12-01

Three different approaches for estimation of maximum magnitude are considered here, along with their implications for managing risk. The first approach is based on a deterministic limit for seismic moment proposed by McGarr (1976), which was originally designed for application to mining-induced seismicity. This approach has since been reformulated for earthquakes induced by fluid injection (McGarr, 2014). In essence, this method assumes that the upper limit for seismic moment release is constrained by the pressure-induced stress change. A deterministic limit is given by the product of shear modulus and the net injected fluid volume. This method is based on the assumptions that the medium is fully saturated and in a state of incipient failure. An alternative geometrical approach was proposed by Shapiro et al. (2011), who postulated that the rupture area for an induced earthquake falls entirely within the stimulated volume. This assumption reduces the maximum-magnitude problem to one of estimating the largest potential slip surface area within a given stimulated volume. Finally, van der Elst et al. (2016) proposed that the maximum observed magnitude, statistically speaking, is the expected maximum value for a finite sample drawn from an unbounded Gutenberg-Richter distribution. These three models imply different approaches for risk management. The deterministic method proposed by McGarr (2014) implies that a ceiling on the maximum magnitude can be imposed by limiting the net injected volume, whereas the approach developed by Shapiro et al. (2011) implies that the time-dependent maximum magnitude is governed by the spatial size of the microseismic event cloud. Finally, the sample-size hypothesis of Van der Elst et al. (2016) implies that the best available estimate of the maximum magnitude is based upon observed seismicity rate. The latter two approaches suggest that real-time monitoring is essential for effective management of risk. A reliable estimate of maximum

The shouted voice: A pilot study of laryngeal physiology under extreme aerodynamic pressure.

Science.gov (United States)

Lagier, Aude; Legou, Thierry; Galant, Camille; Amy de La Bretèque, Benoit; Meynadier, Yohann; Giovanni, Antoine

2017-12-01

The objective was to study the behavior of the larynx during shouted voice production, when the larynx is exposed to extremely high subglottic pressure. The study involved electroglottographic, acoustic, and aerodynamic analyses of shouts produced at maximum effort by three male participants. Under a normal speaking voice, the voice sound pressure level (SPL) is proportional to the subglottic pressure. However, when the subglottic pressure reached high levels, the voice SPL reached a maximum value and then decreased as subglottic pressure increased further. Furthermore, the electroglottographic signal sometimes lost its periodicity during the shout, suggesting irregular vocal fold vibration.

Glovebox pressure relief and check valve

Energy Technology Data Exchange (ETDEWEB)

Blaedel, K.L.

1986-03-17

This device is a combined pressure relief valve and check valve providing overpressure protection and preventing back flow into an inert atmosphere enclosure. The pressure relief is embodied by a submerged vent line in a mercury reservior, the releif pressure being a function of the submerged depth. The pressure relief can be vented into an exhaust system and the relieving pressure is only slightly influenced by the varying pressure in the exhaust system. The check valve is embodied by a ball which floats on the mercury column and contacts a seat whenever vacuum exists within the glovebox enclosure. Alternatively, the check valve is embodied by a vertical column of mercury, the maximum back pressure being a function of the height of the column of mercury.

Glovebox pressure relief and check valve

International Nuclear Information System (INIS)

Blaedel, K.L.

1986-01-01

This device is a combined pressure relief valve and check valve providing overpressure protection and preventing back flow into an inert atmosphere enclosure. The pressure relief is embodied by a submerged vent line in a mercury reservior, the releif pressure being a function of the submerged depth. The pressure relief can be vented into an exhaust system and the relieving pressure is only slightly influenced by the varying pressure in the exhaust system. The check valve is embodied by a ball which floats on the mercury column and contacts a seat whenever vacuum exists within the glovebox enclosure. Alternatively, the check valve is embodied by a vertical column of mercury, the maximum back pressure being a function of the height of the column of mercury

40 CFR 89.407 - Engine dynamometer test run.

Science.gov (United States)

2010-07-01

... supplied to the engine, the fuel temperature, the intake air humidity, and the observed barometric pressure... permitted to precondition the engine at rated speed and maximum horsepower until the oil and water... completion of the test. (3) It is permissible to change filter elements between test modes. (4) A leak check...

Increasing preferred step rate during running reduces plantar pressures.

Science.gov (United States)

Gerrard, James M; Bonanno, Daniel R

2018-01-01

Increasing preferred step rate during running is a commonly used strategy in the management of running-related injuries. This study investigated the effect of different step rates on plantar pressures during running. Thirty-two healthy runners ran at a comfortable speed on a treadmill at five step rates (preferred, ±5%, and ±10%). For each step rate, plantar pressure data were collected using the pedar-X in-shoe system. Compared to running with a preferred step rate, a 10% increase in step rate significantly reduced peak pressure (144.5±46.5 vs 129.3±51 kPa; P=.033) and maximum force (382.3±157.6 vs 334.0±159.8 N; P=.021) at the rearfoot, and reduced maximum force (426.4±130.4 vs 400.0±116.6 N; P=.001) at the midfoot. In contrast, a 10% decrease in step rate significantly increased peak pressure (144.5±46.5 vs 161.5±49.3 kPa; P=.011) and maximum force (382.3±157.6 vs 425.4±155.3 N; P=.032) at the rearfoot. Changing step rate by 5% provided no effect on plantar pressures, and no differences in plantar pressures were observed at the medial forefoot, lateral forefoot or hallux between the step rates. This study's findings indicate that increasing preferred step rate by 10% during running will reduce plantar pressures at the rearfoot and midfoot, while decreasing step rate by 10% will increase plantar pressures at the rearfoot. However, changing preferred step rate by 5% will provide no effect on plantar pressures, and forefoot pressures are unaffected by changes in step rate. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Conditions for maximum isolation of stable condensate during separation in gas-condensate systems

Energy Technology Data Exchange (ETDEWEB)

Trivus, N.A.; Belkina, N.A.

1969-02-01

A thermodynamic analysis is made of the gas-liquid separation process in order to determine the relationship between conditions of maximum stable condensate separation and physico-chemical nature and composition of condensate. The analysis was made by considering the multicomponent gas-condensate fluid produced from Zyrya field as a ternary system, composed of methane, an intermediate component (propane and butane) and a heavy residue, C/sub 6+/. Composition of 5 ternary systems was calculated for a wide variation in separator conditions. At each separator pressure there is maximum condensate production at a certain temperature. This occurs because solubility of condensate components changes with temperature. Results of all calculations are shown graphically. The graphs show conditions of maximum stable condensate separation.

Exploring Permission-Induced Risk in Android Applications for Malicious Application Detection

KAUST Repository

Wang, Wei; Wang, Xing; Feng, Dawei; Liu, Jiqiang; Han, Zhen; Zhang, Xiangliang

2014-01-01

Android has been a major target of malicious applications (malapps). How to detect and keep the malapps out of the app markets is an ongoing challenge. One of the central design points of Android security mechanism is permission control

34 CFR 222.194 - Are “in-kind” contributions permissible?

Science.gov (United States)

2010-07-01

.... (b) Third party in-kind contributions mean property or services that benefit this grant program and... indirect costs, the provisions of 34 CFR 80.24 govern the allowability and valuation of in-kind contributions, except that it is permissible for a third party to contribute real property to a grantee for a...

Traffic-related air pollution and noise and children's blood pressure: results from the PIAMA birth cohort study.

Science.gov (United States)

Bilenko, Natalya; van Rossem, Lenie; Brunekreef, Bert; Beelen, Rob; Eeftens, Marloes; Hoek, Gerard; Houthuijs, Danny; de Jongste, Johan C; van Kempen, Elise; Koppelman, Gerard H; Meliefste, Kees; Oldenwening, Marieke; Smit, Henriette A; Wijga, Alet H; Gehring, Ulrike

2015-01-01

Elevation of a child's blood pressure may cause possible health risks in later life. There is evidence for adverse effects of exposure to air pollution and noise on blood pressure in adults. Little is known about these associations in children. We investigated the associations of air pollution and noise exposure with blood pressure in 12-year-olds. Blood pressure was measured at age 12 years in 1432 participants of the PIAMA birth cohort study. Annual average exposure to traffic-related air pollution [NO2, mass concentrations of particulate matter with diameters of less than 2.5 µm (PM2.5) and less than 10 µm (PM10), and PM2.5 absorbance] at the participants' home and school addresses at the time of blood pressure measurements was estimated by land-use regression models. Air pollution exposure on the days preceding blood pressure measurements was estimated from routine air monitoring data. Long-term noise exposure was assessed by linking addresses to modelled equivalent road traffic noise levels. Associations of exposures with blood pressure were analysed by linear regression. Effects are presented for an interquartile range increase in exposure. Long-term exposure to NO2 and PM2.5 absorbance were associated with increased diastolic blood pressure, in children who lived at the same address since birth [adjusted mean difference (95% confidence interval) [mmHg] 0.83 (0.06 to 1.61) and 0.75 (-0.08 to 1.58), respectively], but not with systolic blood pressure. We found no association of blood pressure with short-term air pollution or noise exposure. Long-term exposure to traffic-related air pollution may increase diastolic blood pressure in children. © The European Society of Cardiology 2013 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Determination of the optimum pressure for neutron yield with d2, in the PF facility dena

International Nuclear Information System (INIS)

Siahpoush, V.; Khorram, C.; Sobhanian, S.; Hamzeh Fafreshi, M. A.

2003-01-01

Using physical model, which describes the dynamics of plasma in the Filipov type plasma focus, we have simulated the pinch current for different voltages and pressures. The results show that for a specific voltage, there is an optimum pressure for which the pinch current has maximum value. A comparison between the simulated and the experimental data from dena shows that the maximum values of pinch current are obtained at the same pressure for which the maximum neutron yield is observed

ESTABLISHMENT OF THE PERMISSIBLE TRAIN SPEED ON THE CURVED TURNOUTS

Directory of Open Access Journals (Sweden)

O. M. Patlasov

2016-04-01

Full Text Available Purpose. Turnouts play a key role in the railway transportation process. One-sided and many-sided curved turnouts were railed over the last 20 years in difficult conditions (curved sections, yard necks. They have a number of geometric features, unlike the conventional one-sided turnouts. Today the normative documents prohibit laying such turnouts in curved track sections and only partially regulate the assessment procedure of their real condition. The question of establishment the permissible train speed within the curved turnouts is still open. In this regard, authors propose to set the train speed according to the driving comfort criterion using the results of field measurements of ordinates from the baseline for the particular curved turnout. Methodology. The article considers the criteria using which one can set the permissible speed on the turnouts. It defines the complexity of their application, advantages and disadvantages. Findings. The work analyzes the speed distribution along the length of the real curved turnout for the forward and lateral directions. It establishes the change rate values of unbalanced accelerations for the existing norms of the curved track sections maintenance according to the difference in the adjacent bend versine at speeds up to 160 km/h. Originality. A method for establishing the trains’ speed limit within the curved turnouts was developed. It takes into account the actual geometric position in the plan of forward and lateral turnout directions. This approach makes it possible to establish a barrier places in plan on the turnouts limiting the train speed. Practical value. The proposed method makes it possible to objectively assess and set the trains’ permissible speed on the basis of the ordinate measurement of the forward and lateral directions of the curved turnouts from the baseline using the driving comfort criteria. The method was tested using real turnouts, which are located within the Pridneprovsk

Swedish or American heterosexual college youth: who is more permissive?

Science.gov (United States)

Weinberg, M S; Lottes, I L; Shaver, F M

1995-08-01

Theories of human sexuality have proposed that two factors reduce the double standard of sexuality and lead to a convergence of male and female sexual behavior: the degree of social benefits and amount of power women have in basic societal institutions and the extent to which a society accepts permissive sexual norms. As these factors increase, the strength of the double standard will decrease and the convergence between male and female behaviors will increase. Compared to the United States, Sweden has instituted more policies to promote gender equality and has been thought to accept more permissive premarital sexual attitudes. The focus of the research reported here is to examine country and gender differences in sexual attitudes and sexual behavior for a sample of university students in the United States (N = 407) and Sweden (N = 570). Results indicate that Swedish students endorsed more similar sexual standards for women and men and reported more accepting attitudes than did American students. For sexual behavior, American men reported the most sexual experience, Swedish men the least, with the women of both countries generally in the middle category. Notwithstanding this more permissive behavior on the part of American men, gender convergence with respect to sexual behavior is stronger in Sweden on several of the dimensions examined: age of first engaging in partner-related sexual activities for those who were sexually experienced, relationship with first partner, number of partners both in the last year and in their lifetime, and affective reactions to first coitus. Gender convergence, however, is weaker in Sweden than in the United States with respect to the incidence and frequency of various sexual activities and the degree of satisfaction with current sex life. Findings are discussed with respect to the questions they raise about the current theories that framed this research and the differential amount of sex education provided in the two countries.

Importance of Calibration Method in Central Blood Pressure for Cardiac Structural Abnormalities.

Science.gov (United States)

Negishi, Kazuaki; Yang, Hong; Wang, Ying; Nolan, Mark T; Negishi, Tomoko; Pathan, Faraz; Marwick, Thomas H; Sharman, James E

2016-09-01

Central blood pressure (CBP) independently predicts cardiovascular risk, but calibration methods may affect accuracy of central systolic blood pressure (CSBP). Standard central systolic blood pressure (Stan-CSBP) from peripheral waveforms is usually derived with calibration using brachial SBP and diastolic BP (DBP). However, calibration using oscillometric mean arterial pressure (MAP) and DBP (MAP-CSBP) is purported to provide more accurate representation of true invasive CSBP. This study sought to determine which derived CSBP could more accurately discriminate cardiac structural abnormalities. A total of 349 community-based patients with risk factors (71±5years, 161 males) had CSBP measured by brachial oscillometry (Mobil-O-Graph, IEM GmbH, Stolberg, Germany) using 2 calibration methods: MAP-CSBP and Stan-CSBP. Left ventricular hypertrophy (LVH) and left atrial dilatation (LAD) were measured based on standard guidelines. MAP-CSBP was higher than Stan-CSBP (149±20 vs. 128±15mm Hg, P curve analyses, MAP-CSBP significantly better discriminated LVH compared with Stan-CSBP (area under the curve (AUC) 0.66 vs. 0.59, P = 0.0063) and brachial SBP (0.62, P = 0.027). Continuous net reclassification improvement (NRI) (P AUC 0.63 vs. 0.56, P = 0.005) and conventional brachial SBP (0.58, P = 0.006), whereas Stan-CSBP provided no better discrimination than conventional brachial BP (P = 0.09). CSBP is calibration dependent and when oscillometric MAP and DBP are used, the derived CSBP is a better discriminator for cardiac structural abnormalities. © American Journal of Hypertension, Ltd 2016. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Handling and feeding of biomass to pressurized reactors: safety engineering

Energy Technology Data Exchange (ETDEWEB)

Wilen, Carl; Rautalin, Aimo (Valtion Teknillinen Tutkimuskeskus, Espoo (Finland). Lab. of Fuel and Process Technology)

1993-01-01

There are rather few literature references to or experience of the feed of biomass into a pressurized space. Alternatives given in the literature usually concern handling and feeding technology for coal. Some screw- or piston-operated plug feeders and coal and concrete pump equipment have, however, also been tested with biomasses. Explosion characteristics of fuels and their susceptibility to spontaneous ignition have been studied at both atmospheric and elevated pressures. The maximum explosion pressure and maximum rate of pressure rise, being critical factors in the process design and in the choice of safety equipment, have been determined under these conditions. In pressurized processes, the maintenance of sufficient inertization in fuel-feed systems is an especially critical factor. Peat, bark, and forest residues were used as biofuels, and lignite was used as reference fuel. The results obtained with a dynamic method for spontaneous ignition were compared with experience obtained from the operation of a commercial pressurized peat gasifier of 140 MW. (author)

Studies on unsteady pressure fields in the region of separating and reattaching flows

Science.gov (United States)

Govinda Ram, H. S.; Arakeri, V. H.

1990-12-01

Experimental studies on the measurement of pressure fields in the region of separating and reattaching flows behind several two-dimensional fore-bodies and one axisymmetric body are reported. In particular, extensive measurements of mean pressure, surface pressure fluctuation, and pressure fluctuation within the flow were made for a series of two-dimensional fore-body shapes consisting of triangular nose with varying included angle. The measurements from different bodies are compared and one of the important findings is that the maximum values of rms pressure fluctuation levels in the shear layer approaching reattachment are almost equal to the maximum value of the surface fluctuation levels.

High hydrostatic pressure leads to free radicals accumulation in yeast cells triggering oxidative stress.

Science.gov (United States)

Bravim, Fernanda; Mota, Mainã M; Fernandes, A Alberto R; Fernandes, Patricia M B

2016-08-01

Saccharomyces cerevisiae is a unicellular organism that during the fermentative process is exposed to a variable environment; hence, resistance to multiple stress conditions is a desirable trait. The stress caused by high hydrostatic pressure (HHP) in S. cerevisiae resembles the injuries generated by other industrial stresses. In this study, it was confirmed that gene expression pattern in response to HHP displays an oxidative stress response profile which is expanded upon hydrostatic pressure release. Actually, reactive oxygen species (ROS) concentration level increased in yeast cells exposed to HHP treatment and an incubation period at room pressure led to a decrease in intracellular ROS concentration. On the other hand, ethylic, thermic and osmotic stresses did not result in any ROS accumulation in yeast cells. Microarray analysis revealed an upregulation of genes related to methionine metabolism, appearing to be a specific cellular response to HHP, and not related to other stresses, such as heat and osmotic stresses. Next, we investigated whether enhanced oxidative stress tolerance leads to enhanced tolerance to HHP stress. Overexpression of STF2 is known to enhance tolerance to oxidative stress and we show that it also leads to enhanced tolerance to HHP stress. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Radioactive contamination of foodstuffs: determination of permissible levels; Contamination radioactive des denrees alimentaires: determination des niveaux admissibles

Energy Technology Data Exchange (ETDEWEB)

Ledermann, S [Commissariat a l' Energie Atomique, Fontenay- aux-Roses (France). Centre d' Etudes Nucleaires

1965-07-01

In a latent air-soil contamination situation, the population would receive 80 per cent of its contamination through foodstuffs. The supervision of this food poses many problems: sampling, radionuclide dosages, etc. It is also necessary to estimate the maximum permissible concentration of radionuclides in foodstuffs, once the maximum exposure limit for the human body has been fixed. The passage of this level to the maximum concentrations is not simple since a) each radionuclide has its own particular effect on the body; b) their concentrations vary from one foodstuff to another, and c) the average amounts of foodstuffs vary from one population to another. Two methods are given here for estimating the maximum permissible concentrations in foodstuffs, together with the first diets likely to become critical when several of them are to be considered simultaneously. The results depend on the way in which the present situation can change to become critical. This evolutionary path can only be estimated approximately. Two methods are therefore given for studying the sensitivity of the results. As an example, a numerical application of these methods using data actually available is given. The data used is naturally incomplete and this will always be true. This application test indicates however two fields in which an improvement is absolutely necessary. 1 - The obtention of multiple observations (simultaneous dosage of at least 2 radionuclides in the same foodstuff, and simultaneous dosage of at least two foodstuffs for the same radionuclide); this assumes a combined effort by the various organisms; 2 - The reaching of an agreement on the dosage methods used by the various organisms since the results actually available are not comparable. (authors) [French] Dans une situation de contamination air-sol latente, la contamination des populations se ferait a 80 pour cent par l'alimentation. Surveiller cette alimentation pose des problemes complexes: echantillonnage, dosage des

The Influence Of Temperature And Pressure On AP600 Pressure Vessel Analysis By Two Dimensional Finite Element Method

International Nuclear Information System (INIS)

Utaya

1996-01-01

Pressure vessel is an important part of nuclear power plan, and its function is as pressure boundary of cooling water and reactor core. The pressure vessel wall will get pressure and thermal stress. The pressure and thermal stress analysis at the simplified AP600 wall was done. The analysis is carried out by finite method, and then solved by computer. The analysis result show, that the pressure will give the maximum stress at the inner wall (1837 kg/cm 2 ) and decreased to the outer wall (1685 kg/cm 2 ). The temperature will decreased the stress at the inner wall (1769 kg/cm 2 ) and increased the stress at the outer wall (1749 kg/cm 2 )

Safety conditions of using structural steels under high temperature and pressures in hydrogen containing environment

International Nuclear Information System (INIS)

Asviyan, M.B.

1984-01-01

The method for establishing full-strength conditions was suggested on the base of results of creep-rupture test of tube samples under hydrogen pressure and according to permissible stresses in neutral medium. Applicability of the method was considered taking St3 and 12KhM steels as examples. It was shown that the use of suggested dependences and special efficiency factors enables to forecast endurance limit for the given steel grade and assigned partial hydrogen pressure without labour-intensive test conducting

Approximate maximum parsimony and ancestral maximum likelihood.

Science.gov (United States)

Alon, Noga; Chor, Benny; Pardi, Fabio; Rapoport, Anat

2010-01-01

We explore the maximum parsimony (MP) and ancestral maximum likelihood (AML) criteria in phylogenetic tree reconstruction. Both problems are NP-hard, so we seek approximate solutions. We formulate the two problems as Steiner tree problems under appropriate distances. The gist of our approach is the succinct characterization of Steiner trees for a small number of leaves for the two distances. This enables the use of known Steiner tree approximation algorithms. The approach leads to a 16/9 approximation ratio for AML and asymptotically to a 1.55 approximation ratio for MP.

Tying of payment of maximum permissible franchise fee by an electric utility holding a monopoly position to the conclusion of new franchise agreement is an infringement of sections 26, sub-sec. 2, 35, sub-sec. 1 GWB. Mannheim Regional Court, decision of 23 Nov. 1994 - 70 120/94 (Kart.); Koppelung der Zahlung der hoechstzulaessigen Konzessionsabgabe durch ein Elektrizitaetsversorgungsunternehmen mit Monopolstellung an den Abschluss eines neuen Konzessionsvertrages als Verstoss gegen Para. 26 Abs. 2, Para. 35 Abs. 1 GWB. LG Mannheim, Urteil vom 23.11.1994 - 7O 120/94(Kart.)

Energy Technology Data Exchange (ETDEWEB)

Anon.

1995-12-31

If an electric utility holds a monopoly position in a local government district due to a valid demarcation agreement, its attempt to ty payment of the maximum permissible franchise fee to the local government to premature conclusion of a follow-up agreement for a term of 20 years is an infringement of section 26, sub-sec. 2 GWB (law against restraints on competition). The electric utility in this case is liable according to sections 26, sub-sec.2, 35, sub-sec. 1 GWB to pay compensation to the local government amounting to the difference between the maximum permissible franchise fees and the fees actually paid by the utility. (orig.) [Deutsch] Verfuegt ein Elektrizitaetsversorgungsunternehmen infolge eines bestehenden Demarkationsvertrages ueber ein Versorgungsmonopol auf dem Gebiet einer Gemeinde, so verstoesst sein Verhalten, die Zahlung der hoechstzulaessigen Konzessionsabgabe an diese Gemeinde an den vorzeitigen Abschluss eines neuen Konzessionsvertrages mit 20jaehriger Laufzeit zu koppeln, gegen Para. 26 Abs. 2 GWB. Das Versorgungsunternehmen ist in einem solchen Falle gemaess Para. 26 Abs. 2, 35 Abs. 1 GWB zum Ersatz des der Gemeinde entstandenen Schadens in Hoehe der Differenz zwischen den hoechstzulaessigen Konzessionsabgaben und den von dem Versorgungsunternehmen gezahlten Betraegen verpflichtet. (orig.)

Assessment of permissible low-level releases of radionuclides into the marine environment

International Nuclear Information System (INIS)

Kryshev, I.I.; Sazykina, T.G.

2002-01-01

The subject of this paper is radio-ecological assessment of permissible low-level releases of radionuclides in sea waters ensuring the radiological protection of the human population, as well as marine biota. (author)

Methodology for surge pressure evaluation in a water injection system

Energy Technology Data Exchange (ETDEWEB)

Meliande, Patricia; Nascimento, Elson A. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Civil; Mascarenhas, Flavio C.B. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Lab. de Hidraulica Computacional; Dandoulakis, Joao P. [SHELL of Brazil, Rio de Janeiro, RJ (Brazil)

2009-07-01

Predicting transient effects, known as surge pressures, is of high importance for offshore industry. It involves detailed computer modeling that attempts to simulate the complex interaction between flow line and fluid in order to ensure efficient system integrity. Platform process operators normally raise concerns whether the water injection system is adequately designed or not to be protected against possible surge pressures during sudden valve closure. This report aims to evaluate the surge pressures in Bijupira and Salema water injection systems due to valve closure, through a computer model simulation. Comparisons among the results from empirical formulations are discussed and supplementary analysis for Salema system were performed in order to define the maximum volumetric flow rate for which the design pressure was able to withstand. Maximum surge pressure values of 287.76 bar and 318.58 bar, obtained in Salema and Bijupira respectively, using empirical formulations have surpassed the operating pressure design, while the computer model results have pointed the greatest surge pressure value of 282 bar in Salema system. (author)

Intra-abdominal pressure during swimming.

Science.gov (United States)

Moriyama, S; Ogita, F; Huang, Z; Kurobe, K; Nagira, A; Tanaka, T; Takahashi, H; Hirano, Y

2014-02-01

The present study aimed to determine the intra-abdominal pressure during front crawl swimming at different velocities in competitive swimmers and to clarify the relationships between stroke indices and changes in intra-abdominal pressure. The subjects were 7 highly trained competitive collegiate male swimmers. Intra-abdominal pressure was measured during front crawl swimming at 1.0, 1.2 and 1.4 m · s(-1) and during the Valsalva maneuver. Intra-abdominal pressure was taken as the difference between minimum and maximum values, and the mean of 6 stable front crawl stroke cycles was used. Stroke rate and stroke length were also measured as stroke indices. There were significant differences in stroke rate among all velocities (P pressure and stroke rate or stroke length (P pressure and stroke indices when controlling for swimming velocity. These findings do not appear to support the effectiveness of trunk training performed by competitive swimmers aimed at increasing intra-abdominal pressure. © Georg Thieme Verlag KG Stuttgart · New York.

Endotracheal Tube Cuff Pressures in Patients Intubated Prior to Helicopter EMS Transport

Directory of Open Access Journals (Sweden)

Joseph Tennyson

2016-11-01

Full Text Available Introduction Endotracheal intubation is a common intervention in critical care patients undergoing helicopter emergency medical services (HEMS transportation. Measurement of endotracheal tube (ETT cuff pressures is not common practice in patients referred to our service. Animal studies have demonstrated an association between the pressure of the ETT cuff on the tracheal mucosa and decreased blood flow leading to mucosal ischemia and scarring. Cuff pressures greater than 30 cmH2O impede mucosal capillary blood flow. Multiple prior studies have recommended 30 cmH2O as the maximum safe cuff inflation pressure. This study sought to evaluate the inflation pressures in ETT cuffs of patients presenting to HEMS. Methods We enrolled a convenience sample of patients presenting to UMass Memorial LifeFlight who were intubated by the sending facility or emergency medical services (EMS agency. Flight crews measured the ETT cuff pressures using a commercially available device. Those patients intubated by the flight crew were excluded from this analysis as the cuff was inflated with the manometer to a standardized pressure. Crews logged the results on a research form, and we analyzed the data using Microsoft Excel and an online statistical analysis tool. Results We analyzed data for 55 patients. There was a mean age of 57 years (range 18–90. The mean ETT cuff pressure was 70 (95% CI= [61–80] cmH2O. The mean lies 40 cmH2O above the maximum accepted value of 30 cmH2O (p120 cmH2O, the maximum pressure on the analog gauge. Conclusion Patients presenting to HEMS after intubation by the referral agency (EMS or hospital have ETT cuffs inflated to pressures that are, on average, more than double the recommended maximum. These patients are at risk for tracheal mucosal injury and scarring from decreased mucosal capillary blood flow. Hospital and EMS providers should use ETT cuff manometry to ensure that they inflate ETT cuffs to safe pressures.

Permissive Attitude Towards Drug Use, Life Satisfaction, and Continuous Drug Use Among Psychoactive Drug Users in Hong Kong.

Science.gov (United States)

Cheung, N Wt; Cheung, Y W; Chen, X

2016-06-01

To examine the effects of a permissive attitude towards regular and occasional drug use, life satisfaction, self-esteem, depression, and other psychosocial variables in the drug use of psychoactive drug users. Psychosocial factors that might affect a permissive attitude towards regular / occasional drug use and life satisfaction were further explored. We analysed data of a sample of psychoactive drug users from a longitudinal survey of psychoactive drug abusers in Hong Kong who were interviewed at 6 time points at 6-month intervals between January 2009 and December 2011. Data of the second to the sixth time points were stacked into an individual time point structure. Random-effects probit regression analysis was performed to estimate the relative contribution of the independent variables to the binary dependent variable of drug use in the last 30 days. A permissive attitude towards drug use, life satisfaction, and depression at the concurrent time point, and self-esteem at the previous time point had direct effects on drug use in the last 30 days. Interestingly, permissiveness to occasional drug use was a stronger predictor of drug use than permissiveness to regular drug use. These 2 permissive attitude variables were affected by the belief that doing extreme things shows the vitality of young people (at concurrent time point), life satisfaction (at concurrent time point), and self-esteem (at concurrent and previous time points). Life satisfaction was affected by sense of uncertainty about the future (at concurrent time point), self-esteem (at concurrent time point), depression (at both concurrent and previous time points), and being stricken by stressful events (at previous time point). A number of psychosocial factors could affect the continuation or discontinuation of drug use, as well as the permissive attitude towards regular and occasional drug use, and life satisfaction. Implications of the findings for prevention and intervention work targeted at

75 FR 66050 - Permissible Sharing of Client Records by Customs Brokers

Science.gov (United States)

2010-10-27

.... USCBP-2010-0038] RIN 1651-AA80 Permissible Sharing of Client Records by Customs Brokers AGENCIES... the Code of Federal Regulations (CFR) pertaining to the obligations of customs brokers to keep clients' information confidential. The proposed amendment would allow brokers, upon the client's consent in a written...

Development of a new pressure dependent threshold superheated drop detector for neutrons

Energy Technology Data Exchange (ETDEWEB)

Rezaeian, Peiman [Radiation Applications Research School, Nuclear Science and Technology Research Institute, AEOI, PO Box 11365-3486, Tehran (Iran, Islamic Republic of); Raisali, Gholamreza, E-mail: graisali@aeoi.org.ir [Radiation Applications Research School, Nuclear Science and Technology Research Institute, AEOI, PO Box 11365-3486, Tehran (Iran, Islamic Republic of); Akhavan, Azam [Radiation Applications Research School, Nuclear Science and Technology Research Institute, AEOI, PO Box 11365-3486, Tehran (Iran, Islamic Republic of); Ghods, Hossein [Physics and Accelerators Research School, Nuclear Science and Technology Research Institute, AEOI, PO Box 11365-3486, Tehran (Iran, Islamic Republic of); Hajizadeh, Bardia [Radiation Protection Division, AEOI, PO Box 14155-1339, Tehran (Iran, Islamic Republic of)

2015-03-11

In this paper, a set of superheated drop detectors operated at different pressures is developed and fabricated by adding an appropriate amount of Freon-12 liquid on the free surface of the detector. The fabricated detectors have been used for determination of the threshold pressure for 2.89 MeV neutrons of a neutron generator in order to estimate the thermodynamic efficiency. Finally, knowing the thermodynamic efficiency of the detector and in a similar manner, the threshold pressure for {sup 241}Am–Be neutrons is determined and accordingly, the maximum neutron energy of the source spectrum is estimated. The maximum neutron energy of the {sup 241}Am–Be is estimated as 10.97±2.11 MeV. The agreement between this measured maximum energy and the reported value of the {sup 241}Am–Be neutron source shows that the method developed to apply pressure on the superheated drop detectors can be used to control the energy threshold of these detectors.

Development of a new pressure dependent threshold superheated drop detector for neutrons

International Nuclear Information System (INIS)

Rezaeian, Peiman; Raisali, Gholamreza; Akhavan, Azam; Ghods, Hossein; Hajizadeh, Bardia

2015-01-01

In this paper, a set of superheated drop detectors operated at different pressures is developed and fabricated by adding an appropriate amount of Freon-12 liquid on the free surface of the detector. The fabricated detectors have been used for determination of the threshold pressure for 2.89 MeV neutrons of a neutron generator in order to estimate the thermodynamic efficiency. Finally, knowing the thermodynamic efficiency of the detector and in a similar manner, the threshold pressure for 241 Am–Be neutrons is determined and accordingly, the maximum neutron energy of the source spectrum is estimated. The maximum neutron energy of the 241 Am–Be is estimated as 10.97±2.11 MeV. The agreement between this measured maximum energy and the reported value of the 241 Am–Be neutron source shows that the method developed to apply pressure on the superheated drop detectors can be used to control the energy threshold of these detectors

PROBABILISTIC APPROACH FOR THE DETERMINATION OF CUTS PERMISSIBLE BRAKING MODES ON THE GRAVITY HUMPS

Directory of Open Access Journals (Sweden)

Volodymyr BOBROVSKYI

2016-03-01

Full Text Available The paper presents the research results of cuts braking modes on the gravity humps. The objective of this paper is developing the methods for assessment of braking modes of cuts under conditions of fuzziness of their rolling properties, as well as selecting the permissible starting speed range of cuts from retardant positions. As a criterion for assessing the modes of target control of cut rolling speed, it was proposed to use an average gap size on a classification track at the established norms of probable exceeding of permissible speed of cars collision and their stop in retarders. As a criterion for evaluating the modes of interval control of cuts rolling speed, using the risk of their non-separation on the switches was proposed. Using the simulation modeling and mathematical statistics, the configuration of the range of permissible speed of cuts coming out from retardant positions has been set. The conducted researches allow simplifying the choice of cut braking modes in systems of automatic control of cut rolling speed.

Permissive hypercapnia for the prevention of morbidity and mortality in mechanically ventilated newborn infants.

Science.gov (United States)

Woodgate, P G; Davies, M W

2001-01-01

Experimental animal data and uncontrolled, observational studies in human infants have suggested that hyperventilation and hypocapnia may be associated with increased pulmonary and neurodevelopmental morbidity. Protective ventilatory strategies allowing higher levels of arterial CO2 (permissive hypercapnia) are now widely used in adult critical care. The aggressive pursuit of normocapnia in ventilated newborn infants may contribute to the already present burden of lung disease. However, the safe or ideal range for PCO2 in this vulnerable population has not been established. To assess whether, in mechanically ventilated neonates, a strategy of permissive hypercapnia improves short and long term outcomes (esp. mortality, duration of respiratory support, incidence of chronic lung disease and neurodevelopmental outcome). Standard strategies of the Cochrane Neonatal Review Group were used. Searches were made of the Oxford Database of Perinatal Trials, MEDLINE, CINAHL, and Current Contents. Searches were also made of previous reviews including cross-referencing, abstracts, and conference and symposia proceedings published in Pediatric Research. All randomised controlled trials in which a strategy of permissive hypercapnia was compared with conventional strategies aimed at achieving normocapnia (or lower levels of hypercapnia) in newborn infants who are mechanically ventilated were eligible. Standard methods of the Cochrane Neonatal Review Group were used. Trials identified by the search strategy were independently reviewed by each author and assessed for eligibility and trial quality. Data were extracted separately. Differences were compared and resolved. Additional information was requested from trial authors. Only published data were available for review. Results are expressed as relative risk and risk difference for dichotomous outcomes, and weighted mean difference for continuous variables. Two trials involving 269 newborn infants were included. Meta-analysis of

Melting temperature of H2, D2, N2 and СH4 under high pressure

Indian Academy of Sciences (India)

the analysis indicates the presence of the melting maximum in these solids. ... values of the melting temperature in case of hydrogen up to a pressure of 4800 ... temperature, Tm, will rise with the increase in pressure, reach to a maximum and.

State-of-the-art literature review on permissive/protected left-turn control.

Science.gov (United States)

2013-06-01

In spring 2010, the Illinois Department of Transportation initiated an areawide implementation to integrate the : flashing yellow arrow as the display for the left-turn permissive interval at more than 100 intersections operating : with protected/per...

Notifiable events in systems for fission of nuclear fuels - nuclear power plants and research reactors with maximum output exceeding 50 kW of thermal normal rating - in the Federal Republic of Germany. Quarterly report, 2nd quarter of 1996

International Nuclear Information System (INIS)

1996-01-01

There were 32 notifiable events in nuclear power plants in Germany in the second quarter of 1996. The report lists and characterises all the 32 events notified in the reporting period. The events did not involve any radioactivity release exceeding the maximum permissible limits during this period, so that there were no radiation hazards to the population or the environment. One event was classified at level 1 of the INES event scale (Anomaly). Research reactor operators in Germany reported 5 notifiable events in the reporting period. The report lists and characterises these events. These events did not involve any radioactivity release exceeding the maximum permissible limits during this period, so that there were no radiation hazards to the population or the environment. All events notified were classified into the lowest categories of safety significance of the official event scales (N, or below scale). (orig./DG) [de

Fundamentals of high pressure adsorption

Energy Technology Data Exchange (ETDEWEB)

Zhou, Y.P.; Zhou, L. [Tianjin University, Tianjin (China). High Pressure Adsorption Laboratory

2009-12-15

High-pressure adsorption attracts research interests following the world's attention to alternative fuels, and it exerts essential effect on the study of hydrogen/methane storage and the development of novel materials addressing to the storage. However, theoretical puzzles in high-pressure adsorption hindered the progress of application studies. Therefore, the present paper addresses the major theoretical problems that challenged researchers: i.e., how to model the isotherms with maximum observed in high-pressure adsorption; what is the adsorption mechanism at high pressures; how do we determine the quantity of absolute adsorption based on experimental data. Ideology and methods to tackle these problems are elucidated, which lead to new insights into the nature of high-pressure adsorption and progress in application studies, for example, in modeling multicomponent adsorption, hydrogen storage, natural gas storage, and coalbed methane enrichment, was achieved.

Automatic Blood Pressure Measurements During Exercise

Science.gov (United States)

Weaver, Charles S.

1985-01-01

Microprocessor circuits and a computer algorithm for automatically measuring blood pressure during ambulatory monitoring and exercise stress testing have been under development at SRI International. A system that records ECG, Korotkov sound, and arm cuff pressure for off-line calculation of blood pressure has been delivered to NASA, and an LSLE physiological monitoring system that performs the algorithm calculations in real-time is being constructed. The algorithm measures the time between the R-wave peaks and the corresponding Korotkov sound on-set (RK-interval). Since the curve of RK-interval versus cuff pressure during deflation is predictable and slowly varying, windows can be set around the curve to eliminate false Korotkov sound detections that result from noise. The slope of this curve, which will generally decrease during exercise, is the inverse of the systolic slope of the brachial artery pulse. In measurements taken during treadmill stress testing, the changes in slopes of subjects with coronary artery disease were markedly different from the changes in slopes of healthy subjects. Measurements of slope and O2 consumption were also made before and after ten days of bed rest during NASA/Ames Research Center bed rest studies. Typically, the maximum rate of O2 consumption during the post-bed rest test is less than the maximum rate during the pre-bed rest test. The post-bed rest slope changes differ from the pre-bed rest slope changes, and the differences are highly correlated with the drop in the maximum rate of O2 consumption. We speculate that the differences between pre- and post-bed rest slopes are due to a drop in heart contractility.

29 CFR 3.5 - Payroll deductions permissible without application to or approval of the Secretary of Labor.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Payroll deductions permissible without application to or approval of the Secretary of Labor. 3.5 Section 3.5 Labor Office of the Secretary of Labor CONTRACTORS AND... STATES § 3.5 Payroll deductions permissible without application to or approval of the Secretary of Labor...

Procedures for permission of installation of nuclear power stations

International Nuclear Information System (INIS)

Narita, Yoriaki

1980-01-01

The locations of atomic power stations are first selected by electric power enterprises in consultation with the Ministry of International Trade and Industry or under the guidance of authorities concerned. The surveys of the climate, topography, water and plants in the planned sites and the influences of nuclear power generation to the surrounding areas are made by the enterprisers under the administrative guidance of the MITI. Secondly, the basic project shall be submitted to and decided by the Power Resource Development Council headed by the Prime Minister (Article 10, the Power Resource Development Law). The Council shall, if necessary, call for the attendance of the governors of prefectures concerned and hear their opinions (Article 11, the Law). As the third and most complicated phase, various procedures include; (a) permission of the changes of electrical facilities under the Electricity Enterprises Act; (b) authorization of the installation of reactors under the Nuclear Reactor Regulation Law; (c) permission or authorization under other regulations including the Agricultural Land Act, etc.; (d) additional procedures related to the indemnification to fishery and so forth. Finally the reactors are to be operated after receiving the certificates of the Minister of ITI on the inspections of construction works, nuclear fuel materials used for the reactors and welding processes of reactor containment vessels, boilers, turbines, etc. (Okada, K.)

Intrarectal pressures and balloon expulsion related to evacuation proctography.

Science.gov (United States)

Halligan, S; Thomas, J; Bartram, C

1995-01-01

Seventy four patients with constipation were examined by standard evacuation proctography and then attempted to expel a small, non-deformable rectal balloon, connected to a pressure transducer to measure intrarectal pressure. Simultaneous imaging related the intrarectal position of the balloon to rectal deformity. Inability to expel the balloon was associated proctographically with prolonged evacuation, incomplete evacuation, reduced anal canal diameter, and acute anorectal angulation during evacuation. The presence and size of rectocoele or intussusception was unrelated to voiding of paste or balloon. An independent linear combination of pelvic floor descent and evacuation time on proctography correctly predicted maximum intrarectal pressure in 74% of cases. No patient with both prolonged evacuation and reduced pelvic floor descent on proctography could void the balloon, as maximum intrarectal pressure was reduced in this group. A prolonged evacuation time on proctography, in combination with reduced pelvic floor descent, suggests defecatory disorder may be caused by inability to raise intrarectal pressure. A diagnosis of anismus should not be made on proctography solely on the basis of incomplete/prolonged evacuation, as this may simply reflect inadequate straining. PMID:7672656

77 FR 17367 - Permissible Sharing of Client Records by Customs Brokers

Science.gov (United States)

2012-03-26

...-0038] RIN 1651-AA80 Permissible Sharing of Client Records by Customs Brokers AGENCY: U.S. Customs and... would allow brokers, upon the client's consent in a written authorization, to share client information... services to the broker's clients. Although the proposed rule was prepared in response to a request from a...

A cash flow oriented EOQ model under permissible delay in payments

African Journals Online (AJOL)

A cash flow oriented EOQ model under permissible delay in payments. RP Tripathi, SS Misra, HS Shukla. Abstract. This study presents an inventory model to determine an optimal ordering policy for non-deteriorating items and timedependent demand rate with delay in payments permitted by the supplier under inflation and ...

Estimating permissible /sup 129/I-emission rates

Energy Technology Data Exchange (ETDEWEB)

Huebschmann, W G

1976-06-01

A mathematical method of iodine release limitation is presented which, in assessing the radiological effectiveness of /sup 129/I, takes advantage of the fact that the chemical behaviour of /sup 129/I resembles that of /sup 131/I and relies on the already extensive knowledge of the chemical and biological behaviour of /sup 131/I. If this method is used for calculating permissible /sup 129/I emission rates it is stated that no unnecessary restrictions need be imposed on a fuel reprocessing plant and that the grazing season for the pasture-cow-milk pathway can be taken into account. The concept is currently in use at the Karlsruhe Nuclear Research Center and seems to be appropriate for licensing of nuclear fuel reprocessing plants.

High-pressure structural study of yttrium monochalcogenides from experiment and theory

DEFF Research Database (Denmark)

Vaitheeswaran, G.; Kanchana, V.; Svane, A.

2011-01-01

High-pressure powder x-ray diffraction experiments using synchrotron radiation are performed on the yttrium monochalcogenides YS, YSe, and YTe up to a maximum pressure of 23 GPa. The ambient NaCl structure is stable throughout the pressure range covered. The bulk moduli are determined to be 93, 82...

Progress report: qualitative differences between first and second order fit of pressure data - 1/5 scale Mk I BWR pressure suppression experiment and analysis program

International Nuclear Information System (INIS)

Carr, E.; Lai, W.; McCauley, E.

1979-01-01

Results are presented for the 1/5-scale Mark I boiling water reactor pressure suppression experiment. The objective of this study is to calculate the hydrodynamic vertical load function (HVLF) and the maximum download and maximum upload ratios for the 90 0 sector to 7.5 0 section (i.e., the 3D to 2D ratios) together with their associated error bounds. Special graphs are presented of the pressure data that are useful in diagnostic studies of the HVLF. These graphs are three dimensional plots which depict the spatially dependent pressure as a function of time. These plots are qualitative but present an overview, not available by other means, which permits grasp of the subtle complex pattern of transient spatial changes in pressure excited by the dynamics in the pool. Sufficient text is included to describe the general feature of each plot

Evaluation of pressure response in the Los Alamos controlled air incinerator during three incident scenarios

International Nuclear Information System (INIS)

Vavruska, J.S.; Elsberry, K.; Thompson, T.K.; Pendergrass, J.A.

1996-01-01

The Los Alamos Controlled Air Incinerator (CAI) is a system designed to accept radioactive mixed waste containing alpha-emitting radionuclides. A mathematical model was developed to predict the pressure response throughout the offgas treatment system of the CAI during three hypothetical incident scenarios. The scenarios examined included: (1) loss of burner flame and failure of the flame safeguard system with subsequent reignition of fuel gas in the primary chamber, (2) pyrolytic gas buildup from a waste package due to loss of induced draft and subsequent restoration of induced draft, and (3) accidental charging of propellant spray cans in a solid waste package to the primary chamber during a normal feed cycle. For each of the three scenarios, the finite element computer model was able to determine the transient pressure surge and decay response throughout the system. Of particular interest were the maximum absolute pressures attainable at critical points in the system as well as maximum differential pressures across the high efficiency particulate air (HEPA) filters. Modeling results indicated that all three of the scenarios resulted in maximum HEPA filter differential pressures well below the maximum allowable levels

Portal pressure correlated to visceral circulation times

Energy Technology Data Exchange (ETDEWEB)

Friman, L [Serafimerlasarettet, Stockholm (Sweden)

1979-01-01

Visceral angiography was performed in 7 patients with normal portal pressure and in 10 with portal hypertension. Circulation times, size of vessels and portal pressure were determined. At celiac angiography, a direct correlation was found between time for maximum filling of portal vein and portal pressure, provided no vascular abnormalities existed. At superior mesenteric angiography such a correlation was not found; loss of flow by shunts in portal hypertension being one explanation. Portocaval shunts are common in the celiac system, but uncommon in the superior mesenteric system.

High pressure studies of fluorenone emission in plastic media

International Nuclear Information System (INIS)

Mitchell, D.J.; Schuster, G.B.; Drickamer, H.G.

1977-01-01

The energy and the quantum efficiency for fluorenone fluorescence in the crystalline state and in polymeric matrices was measured as a function of external pressure over the range 0--140 kbar. The application of high pressure induces changes in the quantum yield, which ranges from 0.001 at low pressure to a maximum of approx.0.1 at high pressure in hydrocarbon plastics. These results are interpreted as arising from the decrease in the energy of the lowest ππ excited singlet state relative to other relevant states as the external pressure is increased

Account of low temperature hardening in calculation of permissible stresses

International Nuclear Information System (INIS)

Novikov, N.V.; Ul'yanenko, A.P.; Gorodyskij, N.I.

1980-01-01

Suggested is a calculation scheme of permissible stresses with the account of temperature hardening for steels and alloys, the dependences of strength, plasticity and rupture work of which on cooling temperature do not have threshold changes in a wide range of low temperatures (from 300 to 4.2 K). Application of the suggested scheme is considered on the example of 12Kh18N10T austenitic chromium-nickel steel

Mycobacteria exploit nitric oxide-induced transformation of macrophages into permissive giant cells.

Science.gov (United States)

Gharun, Kourosh; Senges, Julia; Seidl, Maximilian; Lösslein, Anne; Kolter, Julia; Lohrmann, Florens; Fliegauf, Manfred; Elgizouli, Magdeldin; Vavra, Martina; Schachtrup, Kristina; Illert, Anna L; Gilleron, Martine; Kirschning, Carsten J; Triantafyllopoulou, Antigoni; Henneke, Philipp

2017-12-01

Immunity to mycobacteria involves the formation of granulomas, characterized by a unique macrophage (MΦ) species, so-called multinucleated giant cells (MGC). It remains unresolved whether MGC are beneficial to the host, that is, by prevention of bacterial spread, or whether they promote mycobacterial persistence. Here, we show that the prototypical antimycobacterial molecule nitric oxide (NO), which is produced by MGC in excessive amounts, is a double-edged sword. Next to its antibacterial capacity, NO propagates the transformation of MΦ into MGC, which are relatively permissive for mycobacterial persistence. The mechanism underlying MGC formation involves NO-induced DNA damage and impairment of p53 function. Moreover, MGC have an unsurpassed potential to engulf mycobacteria-infected apoptotic cells, which adds a further burden to their antimycobacterial capacity. Accordingly, mycobacteria take paradoxical advantage of antimicrobial cellular efforts by driving effector MΦ into a permissive MGC state. © 2017 The Authors.

Proposal and design of a natural gas liquefaction process recovering the energy obtained from the pressure reducing stations of high-pressure pipelines

Science.gov (United States)

Tan, Hongbo; Zhao, Qingxuan; Sun, Nannan; Li, Yanzhong

2016-12-01

Taking advantage of the refrigerating effect in the expansion at an appropriate temperature, a fraction of high-pressure natural gas transported by pipelines could be liquefied in a city gate station through a well-organized pressure reducing process without consuming any extra energy. The authors proposed such a new process, which mainly consists of a turbo-expander driven booster, throttle valves, multi-stream heat exchangers and separators, to yield liquefied natural gas (LNG) and liquid light hydrocarbons (LLHs) utilizing the high-pressure of the pipelines. Based on the assessment of the effects of several key parameters on the system performance by a steady-state simulation in Aspen HYSYS, an optimal design condition of the proposed process was determined. The results showed that the new process is more appropriate to be applied in a pressure reducing station (PRS) for the pipelines with higher pressure. For the feed gas at the pressure of 10 MPa, the maximum total liquefaction rate (ytot) of 15.4% and the maximum exergy utilizing rate (EUR) of 21.7% could be reached at the optimal condition. The present process could be used as a small-scale natural gas liquefying and peak-shaving plant at a city gate station.

An analysis of collegiate band directors' exposure to sound pressure levels

Science.gov (United States)

Roebuck, Nikole Moore

Noise-induced hearing loss (NIHL) is a significant but unfortunate common occupational hazard. The purpose of the current study was to measure the magnitude of sound pressure levels generated within a collegiate band room and determine if those sound pressure levels are of a magnitude that exceeds the policy standards and recommendations of the Occupational Safety and Health Administration (OSHA), and the National Institute of Occupational Safety and Health (NIOSH). In addition, reverberation times were measured and analyzed in order to determine the appropriateness of acoustical conditions for the band rehearsal environment. Sound pressure measurements were taken from the rehearsal of seven collegiate marching bands. Single sample t test were conducted to compare the sound pressure levels of all bands to the noise exposure standards of OSHA and NIOSH. Multiple regression analysis were conducted and analyzed in order to determine the effect of the band room's conditions on the sound pressure levels and reverberation times. Time weighted averages (TWA), noise percentage doses, and peak levels were also collected. The mean Leq for all band directors was 90.5 dBA. The total accumulated noise percentage dose for all band directors was 77.6% of the maximum allowable daily noise dose under the OSHA standard. The total calculated TWA for all band directors was 88.2% of the maximum allowable daily noise dose under the OSHA standard. The total accumulated noise percentage dose for all band directors was 152.1% of the maximum allowable daily noise dose under the NIOSH standards, and the total calculated TWA for all band directors was 93dBA of the maximum allowable daily noise dose under the NIOSH standard. Multiple regression analysis revealed that the room volume, the level of acoustical treatment and the mean room reverberation time predicted 80% of the variance in sound pressure levels in this study.

Permissiveness toward divorce : The influence of divorce experiences in three social contexts

NARCIS (Netherlands)

Sieben, I.J.P.; Verbakel, C.M.C.

2013-01-01

In this study, we assess whether divorce experiences in three social contexts shape individual’s permissiveness toward divorce. Using European Values Study data from 44 countries, we find that—net of personal divorce experience—parental divorce before the age of 18 (socialization context); parental

Permissiveness toward divorce: The influence of divorce experiences in three social contexts

NARCIS (Netherlands)

Sieben, I.J.P.; Verbakel, C.M.C.

2013-01-01

In this study, we assess whether divorce experiences in three social contexts shape individual’s permissiveness toward divorce. Using European Values Study data from 44 countries, we find that—net of personal divorce experience—parental divorce before the age of 18 (socialization context); parental

Portal pressure correlated to visceral circulation times

International Nuclear Information System (INIS)

Friman, L.

1979-01-01

Visceral angiography was performed in 7 patients with normal portal pressure and in 10 with portal hypertension. Circulation times, size of vessels and portal pressure were determined. At celiac angiography, a direct correlation was found between time for maximum filling of portal vein and portal pressure, provided no vascular abnormalities existed. At superior mesenteric angiography such a correlation was not found; loss of flow by shunts in portal hypertension being one explanation. Portocaval shunts are common in the celiac system, but uncommon in the superior mesenteric system. (Auth.)

Larval diet affects mosquito development and permissiveness to Plasmodium infection.

Science.gov (United States)

Linenberg, Inbar; Christophides, George K; Gendrin, Mathilde

2016-12-02

The larval stages of malaria vector mosquitoes develop in water pools, feeding mostly on microorganisms and environmental detritus. Richness in the nutrient supply to larvae influences the development and metabolism of larvae and adults. Here, we investigated the effects of larval diet on the development, microbiota content and permissiveness to Plasmodium of Anopheles coluzzii. We tested three fish diets often used to rear mosquitoes in the laboratory, including two pelleted diets, Dr. Clarke's Pool Pellets and Nishikoi Fish Pellets, and one flaked diet, Tetramin Fish-Flakes. Larvae grow and develop faster and produce bigger adults when feeding on both types of pellets compared with flakes. This correlates with a higher microbiota load in pellet-fed larvae, in agreement with the known positive effect of the microbiota on mosquito development. Larval diet also significantly influences the prevalence and intensity of Plasmodium berghei infection in adults, whereby Nishikoi Fish Pellets-fed larvae develop into adults that are highly permissive to parasites and survive longer after infection. This correlates with a lower amount of Enterobacteriaceae in the midgut microbiota. Together, our results shed light on the influence of larval feeding on mosquito development, microbiota and vector competence; they also provide useful data for mosquito rearing.

Identification of significant pressures and assessment of wastewater discharge on Krivaja River water quality

Directory of Open Access Journals (Sweden)

Pešić Vesna Z.

2017-01-01

Full Text Available One of the key stages of the process of preparing management plans for the river basin is the analysis of pressures and impacts, as well as the risk assessment of failing to achieve the environmental objectives. DPSIR framework (Driving Forces-Pressure-State-Impact-Response was developed by the European Agency for the environmental protection, and makes the conceptual basis for the pressures and impacts analysis, taking into account the complexity of the interactions in the environment and represents the tool for their analysis. Impact assessment of the water body requires some quantitative information to describe the condition of the water body and/or the pressures that act on it. The aim of the study was to determine the effect of wastewater discharge on Krivaja watercourse. Impact assessment is carried out based on data of polluters’ wastewater and monitoring information for water in Krivaja. For each site at which sampling was performed, the specific risk quotients for surface water were calculated, as the ratio of the each pollutant concentration in surface water at the sampling point and environmental quality standards for pollutants, as well as their sum that represents the risk index. In order to have the integrated perceive of processes in the Krivaja River, taking into account cumulative effects from point sources, the concept of total maximum daily load was applied, using which the pollution amount, that can be discharged daily in a water body without degrading his prescribed/required quality, was calculated. Comparison of emitted loads from pollution point sources with maximum allowable ones was performed. Wastewaters of different polluters located on Krivaja are, due to insufficient treatment, very loaded with organic matter and nutrients. Krivaja receives daily 1332 m3 of wastewater, 999 kg COD, 722 kg BOD, 144 kg of nitrogen, 4.3 kg of phosphorus and 627 kg of suspended solids. Of the total wastewater volume, the majority (69

Evoked Pressure Pain Sensitivity Is Associated with Differential Analgesic Response to Verum and Sham Acupuncture in Fibromyalgia.

Science.gov (United States)

Zucker, Noah A; Tsodikov, Alex; Mist, Scott D; Cina, Stephen; Napadow, Vitaly; Harris, Richard E

2017-08-01

Fibromyalgia is a chronic pain condition with few effective treatments. Many fibromyalgia patients seek acupuncture for analgesia; however, its efficacy is limited and not fully understood. This may be due to heterogeneous pathologies among participants in acupuncture clinical trials. We hypothesized that pressure pain tenderness would differentially classify treatment response to verum and sham acupuncture in fibromyalgia patients. Baseline pressure pain sensitivity at the thumbnail at baseline was used in linear mixed models as a modifier of differential treatment response to sham versus verum acupuncture. Similarly, needle-induced sensation was also analyzed to determine its differential effect of treatment on clinical pain. A cohort of 114 fibromyalgia patients received baseline pressure pain testing and were randomized to either verum (N = 59) or sham (N = 55) acupuncture. Participants received treatments from once a week to three times a week, increasing in three-week blocks for a total of 18 treatments. Clinical pain was measured on a 101-point visual analog scale, and needle sensation was measured by questionnaire throughout the trial. Participants who had higher pain pressure thresholds had greater reduction in clinical pain following verum acupuncture while participants who had lower pain pressure thresholds showed better analgesic response to sham acupuncture. Moreover, patients with lower pressure pain thresholds had exacerbated clinical pain following verum acupuncture. Similar relationships were observed for sensitivity to acupuncture needling. These findings suggest that acupuncture efficacy in fibromyalgia may be underestimated and a more personalized treatment for fibromyalgia may also be possible. © 2017 American Academy of Pain Medicine. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Larval diet affects mosquito development and permissiveness to Plasmodium infection

OpenAIRE

Gendrin, MEM; Christophides; Linenberg, Inbar

2016-01-01

The larval stages of malaria vector mosquitoes develop in water pools, feeding mostly on microorganisms and environmental detritus. Richness in the nutrient supply to larvae influences the development and metabolism of larvae and adults. Here, we investigated the effects of larval diet on the development, microbiota content and permissiveness to Plasmodium of Anopheles coluzzii . We tested three fish diets often used to rear mosquitoes in the laboratory, including two pelleted diets, Dr. Clar...

Rejection index for pressure tubes

International Nuclear Information System (INIS)

Mitchell, A.B.; Meneley, D.

1989-10-01

The objective of the present study was to establish a set of criteria (or Rejection Index) which could be used to decide whether a zirconium-2 1/2 w/o niobium pressure tube in a CANDU reactor should be removed from service due to in-service degradation. A critique of key issues associated with establishing a realistic rejection index was prepared. Areas of uncertainty in available information were identified and recommendations for further analysis and laboratory testing made. A Rejection Index based on the following limits has been recommended: 1) Limits related to design intent and normal operation: any garter spring must remain within the tolerance band specified for its design location; the annulus gas system must normally be operated in a circulating mode with a procedure in place for purging to prevent accumulation of deuterium. It must remain sensitive to leaks into any part of the systems; and pressure tube dimensions and distortions must be limited to maintain the fuel channels within the original design intent; 2) Limits related to defect tolerance: adequate time margins between occurrence of a leaking crack and unstable failure must be demonstrated for all fuel channels; long lap-type flaws are unacceptable; crack-like defects of any size are unacceptable; and score marks, frat marks and other defects with contoured profiles must fall below certain depth, length and stress intensity limits; and 3) Limits related to property degradation: at operating temperature each pressure tube must be demonstrated to have a critical length in excess of a stipulated value; the maximum equivalent hydrogen level in any pressure tube should not exceed a limit which should be defined taking into account the known history of that tube; the maximum equivalent hydrogen level in any rolled joint should not exceed a limit which is presently recommended as 200 ppm equivalent hydrogen; and the maximum diametral creep strain should be limited to less than 5%

Pressure-time characteristics in diesel engine fueled with natural gas

Energy Technology Data Exchange (ETDEWEB)

Selim, Mohamed Y.E. [Helwan Univ., Mechanical Power Engineering Dept., Cairo (Egypt)

2001-04-01

Combustion pressure data are measured and presented for a dual fuel engine running on dual fuel of diesel and compressed natural gas, and compared to the diesel engine case. The maximum pressure rise rate during combustion is presented as a measure of combustion noise. Experimental investigation on diesel and dual fuel engines revealed the noise generated from combustion in both cases. A Ricardo E6 diesel version engine is converted to run on dual fuel of diesel and compressed natural gas and is used throughout the work. The engine is fully computerized and the cylinder pressure data, crank angle data are stored in a PC for off-line analysis. The effect of engine speeds, loads, pilot injection angle, and pilot fuel quantity on combustion noise is examined for both diesel and dual engine. Maximum pressure rise rate and some samples of ensemble averaged pressure-crank angle data are presented in the present work. The combustion noise, generally, is found to increase for the dual fuel engine case as compared to the diesel engine case. (Author)

Permissive and instructive anterior patterning rely on mRNA localization in the wasp embryo.

Science.gov (United States)

Brent, Ava E; Yucel, Gozde; Small, Stephen; Desplan, Claude

2007-03-30

The long-germ mode of embryogenesis, in which segments arise simultaneously along the anteriorposterior axis, has evolved several times in different lineages of the holometabolous, or fully metamorphosing, insects. Drosophila's long-germ fate map is established largely by the activity of the dipteran-specific Bicoid (Bcd) morphogen gradient, which operates both instructively and permissively to accomplish anterior patterning. By contrast, all nondipteran long-germ insects must achieve anterior patterning independently of bcd. We show that bcd's permissive function is mimicked in the wasp by a maternal repression system in which anterior localization of the wasp ortholog of giant represses anterior expression of the trunk gap genes so that head and thorax can properly form.

[Substantiation of maximum permissible water level of the flotation reagent EFK-1].

Science.gov (United States)

Turbinskiĭ, V V

1991-12-01

Threshold concentrations of the flotation reagent EFK-1 in the water of reservoirs at 0.8 mg/l and 10.0 mg/l for organoleptic and total sanitary indices, respectively, were reported. Dl50 was 7469 mg/kg. The MAC of 0.8 mg/l for EFK-1 in the water of reservoirs (the limiting sign is organoleptic) was proposed.

76 FR 1504 - Pipeline Safety: Establishing Maximum Allowable Operating Pressure or Maximum Operating Pressure...

Science.gov (United States)

2011-01-10

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket No... Mitigation AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA); DOT. ACTION: Notice... system. To that end, the Hazardous Liquid and Gas Transmission Pipeline Integrity Management (IM...

Combustion characteristics and kinetic analysis of pulverized coal under different pressure grades

Directory of Open Access Journals (Sweden)

Qiwei ZUO

2016-02-01

Full Text Available By using thermo gravimetric balance, experimental research on combustion characteristics and dynamics parameters of the typical coal injection from some domestic steelworks are conducted with non-isothermal method. The combustion characteristic parameters of the sample pulverized coal such as ignition temperature, peak temperature at maximum weight loss rate, burnout temperature, general burn exponent(S, and maximum combustion rate are studied under pressure grades of 0.1, 1.1, 2.1, 3.1 and 4.1 MPa, the activation energy (E and pre-exponential factor in the combustion process are calculated. The results show that when the pressure increases from 0.1 to 4.1 MPa, ignition temperature decreases by 85.7 K at most, peak temperature at maximum weight loss rate decreases by 249.3 K at most, burnout temperature decreases by 375 K at most, maximum weight loss rate increases by 10 times, and S increases by 33.6 times at most. It is also shown that there exists a kinetic complementation between E and ln A from the view point of dynamics, and the critical pressure of pulverized coal reaction control requirement and combustion mode transform is 3.1 MPa for the pulverized coal.

Effect of Contact Pressure on the Resistance Contact Value and Temperature Changes in Copper Busbar Connection

Directory of Open Access Journals (Sweden)

Agus Risdiyanto

2012-12-01

Full Text Available This paper discussed the influence of tightness or contacts pressure on copper busbar joints to determine changes in the value of the initial contact resistance and the maximum temperature at the joint due to high current load. The test sample was copper busbar 3 x 30 mm with configuration of bolted overlapping joint. Increasing contact pressure at the joint was measured to find out its effect on the value of contact resistance. The applied pressure was 6 to 36 MPa. Procedure of contact resistance measurement refer to the ASTM B539 standard using four-wire method. The sample subsequently loaded with the current of 350 A for 60 minutes and the maximum temperature at the joint was measured. The result showed that increasing contact pressure at the busbar joint will reduce the contact resistance and maximum temperature. The increase of contact pressure from 6 to 30 MPa causes decreasing contact resistance from 16 μΩ to 11 μΩ. Further increasing of contact pressure more than 30 MPa did not affect the contact resistance significantly. The lowest temperatur of busbar joint of 54°C was reached at a contact pressure of 36 Mpa.

Primary Human Placental Trophoblasts are Permissive for Zika Virus (ZIKV) Replication.

Science.gov (United States)

Aagaard, Kjersti M; Lahon, Anismrita; Suter, Melissa A; Arya, Ravi P; Seferovic, Maxim D; Vogt, Megan B; Hu, Min; Stossi, Fabio; Mancini, Michael A; Harris, R Alan; Kahr, Maike; Eppes, Catherine; Rac, Martha; Belfort, Michael A; Park, Chun Shik; Lacorazza, Daniel; Rico-Hesse, Rebecca

2017-01-27

Zika virus (ZIKV) is an emerging mosquito-borne (Aedes genus) arbovirus of the Flaviviridae family. Although ZIKV has been predominately associated with a mild or asymptomatic dengue-like disease, its appearance in the Americas has been accompanied by a multi-fold increase in reported incidence of fetal microcephaly and brain malformations. The source and mode of vertical transmission from mother to fetus is presumptively transplacental, although a causal link explaining the interval delay between maternal symptoms and observed fetal malformations following infection has been missing. In this study, we show that primary human placental trophoblasts from non-exposed donors (n = 20) can be infected by primary passage ZIKV-FLR isolate, and uniquely allowed for ZIKV viral RNA replication when compared to dengue virus (DENV). Consistent with their being permissive for ZIKV infection, primary trophoblasts expressed multiple putative ZIKV cell entry receptors, and cellular function and differentiation were preserved. These findings suggest that ZIKV-FLR strain can replicate in human placental trophoblasts without host cell destruction, thereby serving as a likely permissive reservoir and portal of fetal transmission with risk of latent microcephaly and malformations.

Maximum discharge rate of liquid-vapor mixtures from vessels

International Nuclear Information System (INIS)

Moody, F.J.

1975-09-01

A discrepancy exists in theoretical predictions of the two-phase equilibrium discharge rate from pipes attached to vessels. Theory which predicts critical flow data in terms of pipe exit pressure and quality severely overpredicts flow rates in terms of vessel fluid properties. This study shows that the discrepancy is explained by the flow pattern. Due to decompression and flashing as fluid accelerates into the pipe entrance, the maximum discharge rate from a vessel is limited by choking of a homogeneous bubbly mixture. The mixture tends toward a slip flow pattern as it travels through the pipe, finally reaching a different choked condition at the pipe exit

The Impact of Different Permissible Exposure Limits on Hearing Threshold Levels Beyond 25 dBA.

Science.gov (United States)

Sayapathi, Balachandar S; Su, Anselm Ting; Koh, David

2014-10-01

Development of noise-induced hearing loss is reliant on a few factors such as frequency, intensity, and duration of noise exposure. The occurrence of this occupational malady has doubled from 120 million to 250 million in a decade. Countries such as Malaysia, India, and the US have adopted 90 dBA as the permissible exposure limit. According to the US Occupational Safety and Health Administration (OSHA), the exposure limit for noise is 90 dBA, while that of the US National Institute of Occupational Safety and Health (NIOSH) is 85 dBA for 8 hours of noise exposure. This study aimed to assess the development of hearing threshold levels beyond 25 dBA on adoption of 85 dBA as the permissible exposure limit compared to 90 dBA. This is an intervention study done on two automobile factories. There were 203 employees exposed to noise levels beyond the action level. Hearing protection devices were distributed to reduce noise levels to a level between the permissible exposure limit and action level. The permissible exposure limits were 90 and 85 dBA in factories 1 and 2, respectively, while the action levels were 85 and 80 dBA, respectively. The hearing threshold levels of participants were measured at baseline and at first month of postshift exposure of noise. The outcome was measured by a manual audiometer. McNemar and chi-square tests were used in the statistical analysis. We found that hearing threshold levels of more than 25 dBA has changed significantly from pre-intervention to post-intervention among participants from both factories (3000 Hz for the right ear and 2000 Hz for the left ear). There was a statistically significant association between participants at 3000 Hz on the right ear at 'deteriorated' level ( χ² (1) = 4.08, φ = - 0.142, P = 0.043), whereas there was worsening of hearing threshold beyond 25 dBA among those embraced 90 dBA. The adoption of 85 dBA as the permissible exposure limit has preserved hearing threshold level among participants at 3000 Hz

Nonstationary pressure build up in full-pressure containments after a loss-of-coolant accident

International Nuclear Information System (INIS)

Mansfeld, G.

1977-01-01

The time histories of pressure, temperature and pressure difference during the pressure build up phase of a loss-of-coolant accident (LOCA) in the primary system in full-pressure containments of water cooled nuclear power reactors are treated. These are important for the design of such containments. The experiments within the German research program RS 50 ''Druckverteilung im Containment'' offered, for the first time, the opportunity to observe experimentally fluid-dynamic processes in a multiple divided full-pressure containment, and to test at the same time, computer codes which serve to describe the physical processes during the LOCA. The comparison of the results calculated by the computer codes ZOCO VI and DDIFF with the experimental results showed apparent deviations by special arrangements of the compartments and the vent flow paths of a model containment for the calculation of time dependent pressure-, temperature- and pressure difference-histories. The deviations lead to the development of the analytical model and computer code COFLOW. This new model was primarily designed to deal with the fluid-dynamic processes in the beginning phase of the blowdown as maximal pressure differences appear. Furthermore, it can be used to determine the maximum containment pressure, as well as for long term calculations. The analytical model and computer code COFLOW shows a better correlation between theory and experiment than previous codes

Comparison of deliverable and exhaustible pressurized air flow rates in laboratory gloveboxes

International Nuclear Information System (INIS)

Compton, J.A.

1994-01-01

Calculations were performed to estimate the maximum credible flow rates of pressurized air into Plutonium Process Support Laboratories gloveboxes. Classical equations for compressible fluids were used to estimate the flow rates. The calculated maxima were compared to another's estimates of glovebox exhaust flow rates and corresponding glovebox internal pressures. No credible pressurized air flow rate will pressurize a glovebox beyond normal operating limits. Unrestricted use of the pressurized air supply is recommended

Pressure RElieving Support SUrfaces: a Randomised Evaluation 2 (PRESSURE 2): study protocol for a randomised controlled trial.

Science.gov (United States)

Brown, Sarah; Smith, Isabelle L; Brown, Julia M; Hulme, Claire; McGinnis, Elizabeth; Stubbs, Nikki; Nelson, E Andrea; Muir, Delia; Rutherford, Claudia; Walker, Kay; Henderson, Valerie; Wilson, Lyn; Gilberts, Rachael; Collier, Howard; Fernandez, Catherine; Hartley, Suzanne; Bhogal, Moninder; Coleman, Susanne; Nixon, Jane E

2016-12-20

Pressure ulcers represent a major burden to patients, carers and the healthcare system, affecting approximately 1 in 17 hospital and 1 in 20 community patients. They impact greatly on an individual's functional status and health-related quality of life. The mainstay of pressure ulcer prevention practice is the provision of pressure redistribution support surfaces and patient repositioning. The aim of the PRESSURE 2 study is to compare the two main mattress types utilised within the NHS: high-specification foam and alternating pressure mattresses, in the prevention of pressure ulcers. PRESSURE 2 is a multicentre, open-label, randomised, double triangular, group sequential, parallel group trial. A maximum of 2954 'high-risk' patients with evidence of acute illness will be randomised on a 1:1 basis to receive either a high-specification foam mattress or alternating-pressure mattress in conjunction with an electric profiling bed frame. The primary objective of the trial is to compare mattresses in terms of the time to developing a new Category 2 or above pressure ulcer by 30 days post end of treatment phase. Secondary endpoints include time to developing new Category 1 and 3 or above pressure ulcers, time to healing of pre-existing Category 2 pressure ulcers, health-related quality of life, cost-effectiveness, incidence of mattress change and safety. Validation objectives are to determine the responsiveness of the Pressure Ulcer Quality of Life-Prevention instrument and the feasibility of having a blinded endpoint assessment using photography. The trial will have a maximum of three planned analyses with unequally spaced reviews at event-driven coherent cut-points. The futility boundaries are constructed as non-binding to allow a decision for stopping early to be overruled by the Data Monitoring and Ethics Committee. The double triangular, group sequential design of the PRESSURE 2 trial will provide an efficient design through the possibility of early stopping for

Evaluating the effects of pentoxifylline administration on experimental pressure sores in rats by biomechanical examinations.

Science.gov (United States)

Velaei, Kobra; Bayat, Mohammad; Torkman, Giti; Rezaie, Fatemealsadat; Amini, Abdollah; Noruzian, Mohsen; Tavassol, Azaedh; Bayat, Mehernoush

2012-09-01

This study used a biomechanical test to evaluate the effects of pentoxifylline administration on the wound healing process of an experimental pressure sore induced in rats. Under general anesthesia and sterile conditions, experimental pressure sores generated by no. 25 Halsted mosquito forceps were inflicted on 12 adult male rats. Pentoxifylline was injected intraperitoneally at a dose of 50 mg/kg daily from the day the pressure sore was generated, for a period of 20 days. At the end of 20 days, rats were sacrificed and skin samples extracted. Samples were biomechanically examined by a material testing instrument for maximum stress (N mm(2)), work up to maximum force (N), and elastic stiffness (N/mm). In the experimental group, maximum stress (2.05±0.15) and work up to maximum force (N/mm) (63.75±4.97) were significantly higher than the control group (1.3±0.27 and 43.3±14.96, P=0.002 and P=0.035, respectively). Pentoxifylline administration significantly accelerated the wound healing process in experimental rats with pressure sores, compared to that of the control group.

Aspects Concerning Modelling Contact Pressure of Polymeric Materials Used in Robotic Soft Elements

Directory of Open Access Journals (Sweden)

Florina-Carmen Ciornei

2015-06-01

Full Text Available Compliant materials are used in applications of robotics for final elements of robotic systems. Contact pressure between a spherical indenter and a linear viscoelastic halfspace is modeled for a cosine normal load. The Maxwell viscoelastic halfspace is described by relaxation function and creep function. For the working frequency domain, the material does not present obvious relaxation. Only for very low frequencies, the pressure variation presents a maximum during approaching delayed with respect to maximum force

Potentiation by aminopeptidase P of blood pressure response to bradykinin.

OpenAIRE

Kitamura, S; Carbini, L A; Carretero, O A; Simmons, W H; Scicli, A G

1995-01-01

We examined whether a specific aminopeptidase P (APP) inhibitor, apstatin, increases vasodepressor responses to bradykinin in anaesthetized rats, and whether it would augment blood pressure responses further after treatment with the angiotensin-converting enzyme inhibitor (ACEi), lisinopril. Apstatin doubled the maximum blood pressure response to bradykinin. The area under the curve (AUC), which incorporates both peak blood pressure changes and duration of response, was doubled in apstatin-tr...

Anomalous superconductivity in black phosphorus under high pressures

International Nuclear Information System (INIS)

Kawamura, H.; Tachikawa, K.

1984-01-01

Pressure induced superconductivity in single crystals of black phosphorus has been studied. Maximum onset Tsub(c) was near 13 K. The anomalous superconductivity may be explained in terms of excitonic mechanism. (author)

Student Learning with Permissive and Restrictive Cell Phone Policies: A Classroom Experiment

Science.gov (United States)

Lancaster, Alexander L.

2018-01-01

Based on Finn and Ledbetter's (2013; 2014) work regarding classroom technology policies, this experimental study examined the implementation of a permissive and a restrictive cellular phone policy and the effect of these policies on students' cognitive and affective learning in two sections of a public speaking course. College students (N = 31)…

Real-time reactor coolant system pressure/temperature limit system

International Nuclear Information System (INIS)

Newton, D.G.; Schemmel, R.R.; Van Scooter, W.E. Jr.

1991-01-01

This patent describes an system, used in controlling the operating of a nuclear reactor coolant system, which automatically calculates and displays allowable reactor coolant system pressure/temperature limits within the nuclear reactor coolant system based upon real-time inputs. It comprises: means for producing signals representative of real-time operating parameters of the nuclear reactor cooling system; means for developing pressure and temperature limits relating the real-time operating parameters of the nuclear reactor coolant system, for normal and emergency operation thereof; means for processing the signals representative of real-time operating parameters of the nuclear reactor coolant system to perform calculations of a best estimate of signals, check manual inputs against permissible valves and test data acquisition hardware for validity and over/under range; and means for comparing the representative signals with limits for the real-time operating parameters to produce a signal for a real-time display of the pressure and temperature limits and of the real-time operating parameters use an operator in controlling the operation of the nuclear reactor coolant system

The impact of xylem cavitation on water potential isotherms measured by the pressure chamber technique in Metasequoia glyptostroboides Hu & W.C. Cheng.

Science.gov (United States)

Yang, Dongmei; Pan, Shaoan; Tyree, Melvin T

2016-08-01

Pressure-volume (PV) curve analysis is the most common and accurate way of estimating all components of the water relationships in leaves (water potential isotherms) as summarized in the Höfler diagram. PV curve analysis yields values of osmotic pressure, turgor pressure, and elastic modulus of cell walls as a function of relative water content. It allows the computation of symplasmic/apoplastic water content partitioning. For about 20 years, cavitation in xylem has been postulated as a possible source of error when estimating the above parameters, but, to the best of the authors' knowledge, no one has ever previously quantified its influence. Results in this paper provide independent estimates of osmotic pressure by PV curve analysis and by thermocouple psychrometer measurement. An anatomical evaluation was also used for the first time to compare apoplastic water fraction estimates from PV analysis with anatomical values. Conclusions include: (i) PV curve values of osmotic pressure are underestimated prior to correcting osmotic pressure for water loss by cavitation in Metasequoia glyptostroboides; (ii) psychrometer estimates of osmotic pressure obtained in tissues killed by freezing or heating agreed with PV values before correction for apoplastic water dilution; (iii) after correction for dilution effects, a solute concentration enhancement (0.27MPa or 0.11 osmolal) was revealed. The possible sources of solute enhancement were starch hydrolysis and release of ions from the Donnan free space of needle cell walls. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Thermodynamic analysis of energy density in pressure retarded osmosis: The impact of solution volumes and costs

International Nuclear Information System (INIS)

Reimund, Kevin K.

2015-01-01

A general method was developed for estimating the volumetric energy efficiency of pressure retarded osmosis via pressure-volume analysis of a membrane process. The resulting model requires only the osmotic pressure, π, and mass fraction, w, of water in the concentrated and dilute feed solutions to estimate the maximum achievable specific energy density, uu, as a function of operating pressure. The model is independent of any membrane or module properties. This method utilizes equilibrium analysis to specify the volumetric mixing fraction of concentrated and dilute solution as a function of operating pressure, and provides results for the total volumetric energy density of similar order to more complex models for the mixing of seawater and riverwater. Within the framework of this analysis, the total volumetric energy density is maximized, for an idealized case, when the operating pressure is π(1+√w -1 ), which is lower than the maximum power density operating pressure, Δπ/2, derived elsewhere, and is a function of the solute osmotic pressure at a given mass fraction. It was also found that a minimum 1.45 kmol of ideal solute is required to produce 1 kWh of energy while a system operating at "maximum power density operating pressure" requires at least 2.9 kmol. Utilizing this methodology, it is possible to examine the effects of volumetric solution cost, operation of a module at various pressure, and operation of a constant pressure module with various feed.

Analytical study on water hammer pressure in pressurized conduits with a throttled surge chamber for slow closure

Directory of Open Access Journals (Sweden)

Yong-liang Zhang

2010-06-01

Full Text Available This paper presents an analytical investigation of water hammer in a hydraulic pressurized pipe system with a throttled surge chamber located at the junction between a tunnel and a penstock, and a valve positioned at the downstream end of the penstock. Analytical formulas of maximum water hammer pressures at the downstream end of the tunnel and the valve were derived for a system subjected to linear and slow valve closure. The analytical results were then compared with numerical ones obtained using the method of characteristics. There is agreement between them. The formulas can be applied to estimating water hammer pressure at the valve and transmission of water hammer pressure through the surge chamber at the junction for a hydraulic pipe system with a surge chamber.

47 CFR 73.525 - TV Channel 6 protection.

Science.gov (United States)

2010-10-01

.... (4) The maximum permissible effective radiated power (ERP) and antenna height may be adjusted for..., the maximum permissible vertically polarized ERP will be the maximum horizontally polarized ERP... it does not. (ii) If the applicant chooses to use mixed polarity, the permissible ERP is as follows...

Nuclear Reactor RA Safety Report, Vol. 16, Maximum hypothetical accident

International Nuclear Information System (INIS)

1986-11-01

Fault tree analysis of the maximum hypothetical accident covers the basic elements: accident initiation, phase development phases - scheme of possible accident flow. Cause of the accident initiation is the break of primary cooling pipe, heavy water system. Loss of primary coolant causes loss of pressure in the primary circuit at the coolant input in the reactor vessel. This initiates safety protection system which should automatically shutdown the reactor. Separate chapters are devoted to: after-heat removal, coolant and moderator loss; accident effects on the reactor core, effects in the reactor building, and release of radioactive wastes [sr

Variations of Negative Pressure Wound Therapy

African Journals Online (AJOL)

a living reaction which serves to eradicate necrotic tissue and suppress bacterial propagation. In order to gain maximum advantages from NPWT, not only the negative pressure environment, but also the selection of the most suitable dressing material will be necessary. Regarding the treatment of diabetic foot ulcers, there.

Comparative Evaluation of Permissiveness to Dengue Virus Serotype 2 Infection in Primary Rodent Macrophages

Directory of Open Access Journals (Sweden)

Jeanette Prada-Arismendy

2012-01-01

Full Text Available Infection with dengue virus presents a broad clinical spectrum, which can range from asymptomatic cases to severe cases that are characterised by haemorrhagic syndrome and/or shock. The reason for such variability remains unknown. This work evaluated the in vitro permissiveness of mouse, rat, hamster and guinea pig macrophages to infection by dengue virus 2 (DENV2. The results established that macrophages derived from the BALB/c mouse strain showed higher permissiveness to DENV2 infection than macrophages from other rodent species, although all rodent species studied had the C820T mutation in the oligoadenylate synthetase 1b gene, indicating no relationship to the different in vitro susceptibilities of mouse cells at this locus. Other molecular mechanisms related to flavivirus susceptibility remain to be explored.

Thermodynamic analysis of energy density in pressure retarded osmosis: The impact of solution volumes and costs

Energy Technology Data Exchange (ETDEWEB)

Reimund, Kevin K. [Univ. of Connecticut, Storrs, CT (United States). Dept. of Chemical and Biomolecular Engineering; McCutcheon, Jeffrey R. [Univ. of Connecticut, Storrs, CT (United States). Dept. of Chemical and Biomolecular Engineering; Wilson, Aaron D. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-08-01

A general method was developed for estimating the volumetric energy efficiency of pressure retarded osmosis via pressure-volume analysis of a membrane process. The resulting model requires only the osmotic pressure, π, and mass fraction, w, of water in the concentrated and dilute feed solutions to estimate the maximum achievable specific energy density, uu, as a function of operating pressure. The model is independent of any membrane or module properties. This method utilizes equilibrium analysis to specify the volumetric mixing fraction of concentrated and dilute solution as a function of operating pressure, and provides results for the total volumetric energy density of similar order to more complex models for the mixing of seawater and riverwater. Within the framework of this analysis, the total volumetric energy density is maximized, for an idealized case, when the operating pressure is π/(1+√w⁻¹), which is lower than the maximum power density operating pressure, Δπ/2, derived elsewhere, and is a function of the solute osmotic pressure at a given mass fraction. It was also found that a minimum 1.45 kmol of ideal solute is required to produce 1 kWh of energy while a system operating at “maximum power density operating pressure” requires at least 2.9 kmol. Utilizing this methodology, it is possible to examine the effects of volumetric solution cost, operation of a module at various pressure, and operation of a constant pressure module with various feed.

The study on the adaptation for regulation - the permission of a radioisotope

Energy Technology Data Exchange (ETDEWEB)

Park, Byoung Il; Choi, Won Seok; Jung, Yong Moon [Gallup Korea, Seoul (Korea, Republic of)

2003-08-15

The restriction -the permission of a radioisotope keeps satisfaction with almost parts for example, awareness, observance and so on. Moreover two concepts are considered fully -too strict about certain specific control rules and needed more discriminated application standards to each organization related to KINS, it's preserved and controlled properly even if the penalties are downsized.

Gender differences in adolescent premarital sexual permissiveness in three Asian cities: effects of gender-role attitudes.

Science.gov (United States)

Zuo, Xiayun; Lou, Chaohua; Gao, Ersheng; Cheng, Yan; Niu, Hongfeng; Zabin, Laurie S

2012-03-01

Gender is an important factor in understanding premarital sexual attitudes and behaviors. Many studies indicate that males are more likely to initiate sexual intercourse and have more permissive perceptions about sex than females. Yet few studies have explored possible reasons for these gender differences. With samples of unmarried adolescents in three Asian cities influenced by Confucian cultures, this article investigates the relationship between underlying gender norms and these differences in adolescents' premarital sexual permissiveness (PSP). In a collaborative survey conducted in 2006-2007 in urban and rural areas of Hanoi, Shanghai, and Taipei, 16,554 unmarried participants aged 15-24 years were recruited in the three-City Asian Study of Adolescents and Youth, with 6,204, 6,023, and 4,327 respondents from each city, respectively. All the adolescents were administered face-to-face interviews, coupled with computer-assisted self-interview for sensitive questions. Scales on gender-role attitudes and on PSP for both male and female respondents were developed and applied to our analysis of the data. Multilinear regression was used to analyze the relationship between gender-role attitudes and sexual permissiveness. Male respondents in each city held more permissive attitudes toward premarital sex than did females, with both boys and girls expressing greater permissiveness to male premarital sexual behaviors. Boys also expressed more traditional attitudes to gender roles (condoning greater inequality) than did girls in each city. Adolescents' gender-role attitudes and permissiveness to premarital sex varied considerably across the three cities, with the Vietnamese the most traditional, the Taiwanese the least traditional, and the adolescents in Shanghai in the middle. A negative association between traditional gender roles and PSP was only found among girls in Shanghai and Taipei. In Shanghai, female respondents who held more traditional gender-role attitudes were

Circadian pattern of blood pressure in normal pregnancy and preeclampsia.

Science.gov (United States)

Gupta, Hem Prabha; Singh, R K; Singh, Urmila; Mehrotra, Seema; Verma, N S; Baranwal, Neelam

2011-08-01

AIMS #ENTITYSTARTX00026; To find out the circadian pattern of blood pressure in normotensive pregnant women and in women with preeclampsia. A cross-sectional prospective observational case control study. Blood pressure was sampled in thirty-five normotensive pregnant women (control) and thirty five preeclamptic women (study group) by using non-invasive automatic ambulatory blood pressure monitoring machine for 72 h. Blood pressure (BP) was not constant over 24 h period and it oscillated from time to time in control group. BP was maximum during early part of afternoon. However, in preeclampsia besides quantitative increase in BP, circadian BP oscillations were less pronounced and in around 50% subjects BP was maximum during evening and night hours. Both systolic and diastolic BP showed definite reproducible circadian pattern in both preeclamptic and normotensive pregnant women. This pattern both quantitatively and qualitatively was different in preeclamptic women. Standardized 24 h BP monitoring allows quantitative and qualitative evaluation of hypertensive status and is important for timing and dosing of antihypertensive medications.

Retinal vessel diameter and estimated cerebrospinal fluid pressure in arterial hypertension: the Beijing Eye Study.

Science.gov (United States)

Jonas, Jost B; Wang, Ningli; Wang, Shuang; Wang, Ya Xing; You, Qi Sheng; Yang, Diya; Wei, Wen Bin; Xu, Liang

2014-09-01

Hypertensive retinal microvascular abnormalities include an increased retinal vein-to-artery diameter ratio. Because central retinal vein pressure depends on cerebrospinal fluid pressure (CSFP), we examined whether the retinal vein-to-artery diameter ratio and other retinal hypertensive signs are associated with CSFP. Participants of the population-based Beijing Eye Study (n = 1,574 subjects) underwent measurement of the temporal inferior and superior retinal artery and vein diameter. CSFP was calculated as 0.44 × body mass index (kg/m(2)) + 0.16 × diastolic blood pressure (mm Hg) - 0.18 × age (years) - 1.91. Larger retinal vein diameters and higher vein-to-artery diameter ratios were significantly associated with higher estimated CSFP (P = 0.001) in multivariable analysis. In contrast, temporal inferior retinal arterial diameter was marginally associated (P = 0.03) with estimated CSFP, and temporal superior artery diameter was not significantly associated (P = 0.10) with estimated CSFP; other microvascular abnormalities, such as arteriovenous crossing signs, were also not significantly associated with estimated CSFP. In a reverse manner, higher estimated CSFP as a dependent variable in the multivariable analysis was associated with wider retinal veins and higher vein-to-artery diameter ratio. In the same model, estimated CSFP was not significantly correlated with retinal artery diameters or other retinal microvascular abnormalities. Correspondingly, arterial hypertension was associated with retinal microvascular abnormalities such as arteriovenous crossing signs (P = 0.003), thinner temporal retinal arteries (P arterial hypertension, an increased retinal vein-to-artery diameter ratio depends on elevated CSFP, which is correlated with blood pressure. © American Journal of Hypertension, Ltd 2014. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Permissive Parenting, Deviant Peer Affiliations, and Delinquent Behavior in Adolescence: the Moderating Role of Sympathetic Nervous System Reactivity.

Science.gov (United States)

Hinnant, J Benjamin; Erath, Stephen A; Tu, Kelly M; El-Sheikh, Mona

2016-08-01

The present study examined two measures of sympathetic nervous system (SNS) activity as moderators of the indirect path from permissive parenting to deviant peer affiliations to delinquency among a community sample of adolescents. Participants included 252 adolescents (M = 15.79 years; 53 % boys; 66 % European American, 34 % African American). A multi-method design was employed to address the research questions. Two indicators of SNS reactivity, skin conductance level reactivity (SCLR) and cardiac pre-ejection period reactivity (PEPR) were examined. SNS activity was measured during a baseline period and a problem-solving task (star-tracing); reactivity was computed as the difference between the task and baseline periods. Adolescents reported on permissive parenting, deviant peer affiliations, externalizing behaviors, and substance use (alcohol, marijuana). Analyses revealed indirect effects between permissive parenting and delinquency via affiliation with deviant peers. Additionally, links between permissive parenting to affiliation with deviant peers and affiliation with deviant peers to delinquency was moderated by SNS reactivity. Less SNS reactivity (less PEPR and/or less SCLR) were risk factors for externalizing problems and alcohol use. Findings highlight the moderating role of SNS reactivity in parenting and peer pathways that may contribute to adolescent delinquency and point to possibilities of targeted interventions for vulnerable youth.

Enhanced monoclonal antibody production by gradual increase of osmotic pressure

OpenAIRE

Lin, Jianqiang; Takagi, Mutsumi; Qu, Yinbo; Gao, Peiji; Yoshida, Toshiomi

1999-01-01

The time length required for the adaptation of AFP-27 hybridoma cells to high osmotic pressure and the effect of a gradual increase of osmotic pressure on monoclonal antibody production were investigated. When the cells were subjected to an increase of osmotic pressure from 300 mOsmol kg-1 to 366 mOsmol kg- 1, the intracellular content of osmoprotective free amino acids reached a maximum level 6 h after the osmotic pressure was increased to 366 mOsmol kg-1. The same time period of 6 h incubat...

49 CFR 350.319 - What are permissible uses of High Priority Activity Funds?

Science.gov (United States)

2010-10-01

... Activity Funds? 350.319 Section 350.319 Transportation Other Regulations Relating to Transportation... permissible uses of High Priority Activity Funds? (a) The FMCSA may generally use these funds to support, enrich, or evaluate State CMV safety programs and to accomplish the five objectives listed below: (1...

Numerical simulation of the pressure pulses produced by a pressure screen foil rotor

International Nuclear Information System (INIS)

Feng, M.; Ollivier-Gooch, C.; Gooding, R.W.; Olson, J.A.

2003-01-01

Pressure screening is the most industrially efficient and effective means of removing contaminants that degrade the appearance and strength of paper and fractionating fibres for selective treatments and specialty products. A critical design component of a screen is the rotor which produces pressure pulses on the screen cylinder surface to keep the screening apertures clear. To understand the effect of the key design and operating variables for a NACA 0012 foil rotor, a computational fluid dynamic (CFD) simulation tool was developed with FLUENT software, and the numerical results were compared with experimental measurements. The computational results of pressure pulses were shown to be in good agreement with experimental pressure measurements over a wide range of foil tip-speeds, clearances and angles of attack. In addition, it was shown that the magnitude of the pressure pulse peak increases as the rotating speed increases linearly with the square of tip-speed for all the angles of attack studied. The maximum negative pressure pulse occurred for the foil at 5 degrees angle of attack. Flow began to separate from foil surface near the screen plate beyond 10 degrees angle of attack. The positive pressure peak near the leading edge of the foil is completely eliminated for foils operating at a positive angle of attack. The magnitude of the negative pressure peak increased as clearance decreased. In addition to, and more important than, these specific results, we have shown that CFD is a viable tool for the optimal design and operation of rotors in industrial pressure screens. (author)

Legal Permissibility of Unilateral Humanitarian Interventions

Directory of Open Access Journals (Sweden)

Petra Perisic

2013-03-01

Full Text Available The paper explores the status of unilateral humanitarian interventions in international law. The United Nations Charter prohibits the use of force, except in case of self-defense and the collective action authorized by the Security Council. The question is whether the non-existence of unilateral humanitarian intervention among these exceptions means that they are not in conformity with the Charter and if so, whether the right to such interventions exists as the part of customary law. The issue has become even more controversial after the adoption of the “responsibility to protect” principle. Findings of legal scholars on this issue differ significantly. This paper analyzes and interprets the Charter provisions in order to answer the question of compatibility of humanitarian interventions with the Charter and examines the state practice in order to conclude whether the customary law rule allowing the humanitarian intervention exists. The conclusion of the paper is that there is no evidence to support the contentions that interventions without the Security Council authorization are permissible, although there are elements which point to the possibility of the creation of customary law allowing them.

Leishmania attachment in permissive vectors and the role of sand fly midgut proteins in parasite-vector interaction

OpenAIRE

Dostálová, Anna

2012-01-01

of PhD. thesis named "Leishmania attachment in permissive vectors and the role of sand fly midgut proteins in parasite-vector interaction", Anna Dostálová, 2011 This thesis focuses on the development of protozoan parasites of the genus Leishmania in their insect vectors, sand flies. It sums up results of three projects I was involved in during my PhD studies. Main emphasis was put on permissive sand fly species that support development of various species of Leishmania. Using a novel method of...

Theoretical Evaluation of the Maximum Work of Free-Piston Engine Generators

Science.gov (United States)

Kojima, Shinji

2017-01-01

Utilizing the adjoint equations that originate from the calculus of variations, we have calculated the maximum thermal efficiency that is theoretically attainable by free-piston engine generators considering the work loss due to friction and Joule heat. Based on the adjoint equations with seven dimensionless parameters, the trajectory of the piston, the histories of the electric current, the work done, and the two kinds of losses have been derived in analytic forms. Using these we have conducted parametric studies for the optimized Otto and Brayton cycles. The smallness of the pressure ratio of the Brayton cycle makes the net work done negative even when the duration of heat addition is optimized to give the maximum amount of heat addition. For the Otto cycle, the net work done is positive, and both types of losses relative to the gross work done become smaller with the larger compression ratio. Another remarkable feature of the optimized Brayton cycle is that the piston trajectory of the heat addition/disposal process is expressed by the same equation as that of an adiabatic process. The maximum thermal efficiency of any combination of isochoric and isobaric heat addition/disposal processes, such as the Sabathe cycle, may be deduced by applying the methods described here.

Overview of the Integrated Pressurized Thermal-Shock (IPTS) study

International Nuclear Information System (INIS)

Cheverton, R.D.

1990-01-01

By the early 1980s, (PTS)-related, deterministic, vessel-integrity studies sponsored by the US Nuclear Regulatory Commission (NRC) indicated a potential for failure of some PWR vessels before design end of life, in the event of a postulated severe PTS transient. In response, the NRC established screening criteria, in the form of limiting values of the reference nil-ductility transition temperature (RT NDT ), and initiated the development of a probabilistic methodology for evaluating vessel integrity. This latter effort, referred to as the Integrated Pressurized Thermal-Shock (IPTS) Program, included development of techniques for postulating PTS transients, estimating their frequencies, and calculating the probability of vessel failure for a specific transient. Summing the products of frequency of transient and conditional probability of failure for each of the many postulated transients provide a calculated value of the frequency of failure. The IPTS Program also included the application of the IPTS methodology to three US PWR plants (Oconee-1, Calvert Cliffs-1, and HBRobinson-2) and the specification of a maximum permissible value of the calculated frequency of vessel failure. Another important purpose of the IPTS study was to determine, through application of the IPTS methodology, which design and operating features, parameters, and PTS transients were dominant in affecting the calculated frequency of failure. The scope of the IPTS Program included the development of a probabilistic fracture-mechanics capability, modification of the TRAC and RELAP5 thermal/hydraulic codes, and development of the methodology for estimating the uncertainty in the calculated frequency of vessel failure

Blood pressure variability and risk of cardiovascular events and death in patients with hypertension and different baseline risks.

Science.gov (United States)

Mehlum, Maria H; Liestøl, Knut; Kjeldsen, Sverre E; Julius, Stevo; Hua, Tsushung A; Rothwell, Peter M; Mancia, Giuseppe; Parati, Gianfranco; Weber, Michael A; Berge, Eivind

2018-01-20

Blood pressure variability is associated with increased risk of cardiovascular events, particularly in high-risk patients. We assessed if variability was associated with increased risk of cardiovascular events and death in hypertensive patients at different risk levels. The Valsartan Antihypertensive Long-term Use Evaluation trial was a randomized controlled trial of valsartan vs. amlodipine in patients with hypertension and different risks of cardiovascular events, followed for a mean of 4.2 years. We calculated standard deviation (SD) of mean systolic blood pressure from visits from 6 months onward in patients with ≥3 visits and no events during the first 6 months. We compared the risk of cardiovascular events in the highest and lowest quintile of visit-to-visit blood pressure variability, using Cox regression. For analysis of death, variability was analysed as a continuous variable. Of 13 803 patients included, 1557 (11.3%) had a cardiovascular event and 1089 (7.9%) died. Patients in the highest quintile of SD had an increased risk of cardiovascular events [hazard ratio (HR) 2.1, 95% confidence interval (95% CI) 1.7-2.4; P risk of death (HR 1.10, 95% CI 1.04-1.17; P = 0.002). Associations were stronger among younger patients and patients with lower systolic blood pressure, and similar between patients with different baseline risks, except for higher risk of death among patients with established cardiovascular disease. Higher visit-to-visit systolic blood pressure variability is associated with increased risk of cardiovascular events in patients with hypertension, irrespective of baseline risk of cardiovascular events. Associations were stronger in younger patients and in those with lower mean systolic blood pressure. Published on behalf of the European Society of Cardiology. All rights reserved. © The Author(s) 2018. For permissions, please email: journals.permissions@oup.com.

Cosmic shear measurement with maximum likelihood and maximum a posteriori inference

Science.gov (United States)

Hall, Alex; Taylor, Andy

2017-06-01

We investigate the problem of noise bias in maximum likelihood and maximum a posteriori estimators for cosmic shear. We derive the leading and next-to-leading order biases and compute them in the context of galaxy ellipticity measurements, extending previous work on maximum likelihood inference for weak lensing. We show that a large part of the bias on these point estimators can be removed using information already contained in the likelihood when a galaxy model is specified, without the need for external calibration. We test these bias-corrected estimators on simulated galaxy images similar to those expected from planned space-based weak lensing surveys, with promising results. We find that the introduction of an intrinsic shape prior can help with mitigation of noise bias, such that the maximum a posteriori estimate can be made less biased than the maximum likelihood estimate. Second-order terms offer a check on the convergence of the estimators, but are largely subdominant. We show how biases propagate to shear estimates, demonstrating in our simple set-up that shear biases can be reduced by orders of magnitude and potentially to within the requirements of planned space-based surveys at mild signal-to-noise ratio. We find that second-order terms can exhibit significant cancellations at low signal-to-noise ratio when Gaussian noise is assumed, which has implications for inferring the performance of shear-measurement algorithms from simplified simulations. We discuss the viability of our point estimators as tools for lensing inference, arguing that they allow for the robust measurement of ellipticity and shear.

A colorimetric sensor array for identification of toxic gases below permissible exposure limits†

OpenAIRE

Feng, Liang; Musto, Christopher J.; Kemling, Jonathan W.; Lim, Sung H.; Suslick, Kenneth S.

2010-01-01

A colorimetric sensor array has been developed for the rapid and sensitive detection of 20 toxic industrial chemicals (TICs) at their PELs (permissible exposure limits). The color changes in an array of chemically responsive nanoporous pigments provide facile identification of the TICs with an error rate below 0.7%.

26 CFR 1.414(w)-1 - Permissible withdrawals from eligible automatic contribution arrangements.

Science.gov (United States)

2010-04-01

... contribution arrangements. 1.414(w)-1 Section 1.414(w)-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT... Plans, Etc. § 1.414(w)-1 Permissible withdrawals from eligible automatic contribution arrangements. (a) Overview. Section 414(w) provides rules under which certain employees are permitted to elect to make a...

Transient pool boiling heat transfer due to increasing heat inputs in subcooled water at high pressures

International Nuclear Information System (INIS)

Fukuda, K.; Shiotsu, M.; Sakurai, A.

1995-01-01

Understanding of transient boiling phenomenon caused by increasing heat inputs in subcooled water at high pressures is necessary to predict correctly a severe accident due to a power burst in a water-cooled nuclear reactor. Transient maximum heat fluxes, q max , on a 1.2 mm diameter horizontal cylinder in a pool of saturated and subcooled water for exponential heat inputs, q o e t/T , with periods, τ, ranging from about 2 ms to 20 s at pressures from atmospheric up to 2063 kPa for water subcoolings from 0 to about 80 K were measured to obtain the extended data base to investigate the effect of high subcoolings on steady-state and transient maximum heat fluxes, q max . Two main mechanisms of q max exist depending on the exponential periods at low subcoolings. One is due to the time lag of the hydrodynamic instability which starts at steady-state maximum heat flux on fully developed nucleate boiling (FDNB), and the other is due to the heterogenous spontaneous nucleations (HSN) in flooded cavities which coexist with vapor bubbles growing up from active cavities. The shortest period corresponding to the maximum q max for long period range belonging to the former mechanism becomes longer and the q max mechanism for long period range shifts to that due the HSN on FDNB with the increase of subcooling and pressure. The longest period corresponding to the minimum q max for the short period range belonging to the latter mechanism becomes shorter with the increase in saturated pressure. On the contrary, the longest period becomes longer with the increase in subcooling at high pressures. Correlations for steady-state and transient maximum heat fluxes were presented for a wide range of pressure and subcooling

Transient pool boiling heat transfer due to increasing heat inputs in subcooled water at high pressures

Energy Technology Data Exchange (ETDEWEB)

Fukuda, K. [Kobe Univ. of Mercantile Marine (Japan); Shiotsu, M.; Sakurai, A. [Kyoto Univ. (Japan)

1995-09-01

Understanding of transient boiling phenomenon caused by increasing heat inputs in subcooled water at high pressures is necessary to predict correctly a severe accident due to a power burst in a water-cooled nuclear reactor. Transient maximum heat fluxes, q{sub max}, on a 1.2 mm diameter horizontal cylinder in a pool of saturated and subcooled water for exponential heat inputs, q{sub o}e{sup t/T}, with periods, {tau}, ranging from about 2 ms to 20 s at pressures from atmospheric up to 2063 kPa for water subcoolings from 0 to about 80 K were measured to obtain the extended data base to investigate the effect of high subcoolings on steady-state and transient maximum heat fluxes, q{sub max}. Two main mechanisms of q{sub max} exist depending on the exponential periods at low subcoolings. One is due to the time lag of the hydrodynamic instability which starts at steady-state maximum heat flux on fully developed nucleate boiling (FDNB), and the other is due to the heterogenous spontaneous nucleations (HSN) in flooded cavities which coexist with vapor bubbles growing up from active cavities. The shortest period corresponding to the maximum q{sub max} for long period range belonging to the former mechanism becomes longer and the q{sub max}mechanism for long period range shifts to that due the HSN on FDNB with the increase of subcooling and pressure. The longest period corresponding to the minimum q{sub max} for the short period range belonging to the latter mechanism becomes shorter with the increase in saturated pressure. On the contrary, the longest period becomes longer with the increase in subcooling at high pressures. Correlations for steady-state and transient maximum heat fluxes were presented for a wide range of pressure and subcooling.

Physical method to assess a probable maximum precipitation, using CRCM datas

International Nuclear Information System (INIS)

Beauchamp, J.

2009-01-01

'Full text:' For Nordic hydropower facilities, spillways are designed with a peak discharge based on extreme conditions. This peak discharge is generally derived using the concept of a probable maximum flood (PMF), which results from the combined effect of abundant downpours (probable maximum precipitation - PMP) and rapid snowmelt. On a gauged basin, the weather data record allows for the computation of the PMF. However, uncertainty in the future climate raises questions as to the accuracy of current PMP estimates for existing and future hydropower facilities. This project looks at the potential use of the Canadian Regional Climate Model (CRCM) data to compute the PMF in ungauged basins and to assess potential changes to the PMF in a changing climate. Several steps will be needed to accomplish this task. This paper presents the first step that aims at applying/adapting to CRCM data the in situ moisture maximization technique developed by the World Meteorological Organization, in order to compute the PMP at the watershed scale. The CRCM provides output data on a 45km grid at a six hour time step. All of the needed atmospheric data is available at sixteen different pressure levels. The methodology consists in first identifying extreme precipitation events under current climate conditions. Then, a maximum persisting twelve hours dew point is determined at each grid point and pressure level for the storm duration. Afterwards, the maximization ratio is approximated by merging the effective temperature with dew point and relative humidity values. The variables and maximization ratio are four-dimensional (x, y, z, t) values. Consequently, two different approaches are explored: a partial ratio at each step and a global ratio for the storm duration. For every identified extreme precipitation event, a maximized hyetograph is computed from the application of this ratio, either partial or global, on CRCM precipitation rates. Ultimately, the PMP is the depth of the

Physical method to assess a probable maximum precipitation, using CRCM datas

Energy Technology Data Exchange (ETDEWEB)

Beauchamp, J. [Univ. de Quebec, Ecole de technologie superior, Quebec (Canada)

2009-07-01

'Full text:' For Nordic hydropower facilities, spillways are designed with a peak discharge based on extreme conditions. This peak discharge is generally derived using the concept of a probable maximum flood (PMF), which results from the combined effect of abundant downpours (probable maximum precipitation - PMP) and rapid snowmelt. On a gauged basin, the weather data record allows for the computation of the PMF. However, uncertainty in the future climate raises questions as to the accuracy of current PMP estimates for existing and future hydropower facilities. This project looks at the potential use of the Canadian Regional Climate Model (CRCM) data to compute the PMF in ungauged basins and to assess potential changes to the PMF in a changing climate. Several steps will be needed to accomplish this task. This paper presents the first step that aims at applying/adapting to CRCM data the in situ moisture maximization technique developed by the World Meteorological Organization, in order to compute the PMP at the watershed scale. The CRCM provides output data on a 45km grid at a six hour time step. All of the needed atmospheric data is available at sixteen different pressure levels. The methodology consists in first identifying extreme precipitation events under current climate conditions. Then, a maximum persisting twelve hours dew point is determined at each grid point and pressure level for the storm duration. Afterwards, the maximization ratio is approximated by merging the effective temperature with dew point and relative humidity values. The variables and maximization ratio are four-dimensional (x, y, z, t) values. Consequently, two different approaches are explored: a partial ratio at each step and a global ratio for the storm duration. For every identified extreme precipitation event, a maximized hyetograph is computed from the application of this ratio, either partial or global, on CRCM precipitation rates. Ultimately, the PMP is the depth of the

Android Application Install-time Permission Validation and Run-time Malicious Pattern Detection

OpenAIRE

Ma, Zhongmin

2014-01-01

The open source structure of Android applications introduces security vulnerabilities that can be readily exploited by third-party applications. We address certain vulnerabilities at both installation and runtime using machine learning. Effective classification techniques with neural networks can be used to verify the application categories on installation. We devise a novel application category verification methodology that involves machine learning the application permissions...

Pressure Stimulated Currents (PSCin marble samples

Directory of Open Access Journals (Sweden)

F. Vallianatos

2004-06-01

Full Text Available The electrical behaviour of marble samples from Penteli Mountain was studied while they were subjected to uniaxial stress. The application of consecutive impulsive variations of uniaxial stress to thirty connatural samples produced Pressure Stimulated Currents (PSC. The linear relationship between the recorded PSC and the applied variation rate was investigated. The main results are the following: as far as the samples were under pressure corresponding to their elastic region, the maximum PSC value obeyed a linear law with respect to pressure variation. In the plastic region deviations were observed which were due to variations of Young s modulus. Furthermore, a special burst form of PSC recordings during failure is presented. The latter is emitted when irregular longitudinal splitting is observed during failure.

Stress concentration factors for pressurized elliptic crossbores in blocks

International Nuclear Information System (INIS)

Badr, Elie A.

2006-01-01

Intersecting bore geometries are used in a number of industrial applications including heavy-walled pressure vessels containing oil holes for lubrication, ports for valves and fluid ends of reciprocating pumps. The bore intersection location is a stress concentration point where the maximum hoop stress can be many times the fluid pressure in the bores. Intersecting circular holes in heavy-walled cylinders and rectangular blocks have been extensively investigated. Specifically, stress/pressure concentration curves for intersecting circular bores in rectangular blocks were presented by Sorem et al. [Sorem JR, Shadley JR, Tipton SM. Design curves for maximum stresses in blocks containing pressurized bore intersections. ASME J Mech Des 1990; 113: 427-31.]. However, stress/pressure concentrations due to intersecting elliptic bores have not been broadly investigated. With the availability of computer numerical control (CNC) machinery, bores with elliptic crosssection can be produced with relative ease. In this paper, hoop stress concentration ratios are developed for elliptic crossbores in rectangular blocks. Results indicate that introducing elliptic crossbores, rather than circular ones, significantly reduces the hoop stress concentration factor at the crossbore intersection. Also, the presence of intersecting crossbores has a major effect on the fatigue life of pressure vessels [Badr EA, Sorem JR, Jr Tipton SM. Evaluation of the autofrettage effect on fatigue lives of steel blocks with crossbores using a statistical and a strain-based method. ASTM J Test Eval 2000; 28: 181-8.] and the reduction of hoop stress concentration is expected to enhance the fatigue life of pressure vessels containing crossbores

Radiation-resistant pressure transducers

International Nuclear Information System (INIS)

Abbasov, Sh.M.; Kerimova, T.I.

2005-01-01

Full text : The sensitive element of vibrofrequency tensor converter (VTC) is an electromechanical resonator of string type with electrostatic excitation of longitudinal mechanical vibrations. The string is made from tensosensitive thread-like monocrystal n-Ge1-x Six (length 1-5 mm, diameter 8-12 mcm) with current outlet and strictly fixed by ends at plate or deformable surface (in elastic element) at 50 mcm apartheid. With increasing Si atomic percent in n-Ge1-x Six the converter tens sensitivity increases. There has been shown the scheme of pressure transducer which contains monocrystalline silicon membrane and string tens converter from thread-like monocrystal Ge-Si. Using method, when crystal position on membrane while it deforms by pressure, corresponds to free (uptight) state, allowed to obtain the maximum sensitivity in measurement of pressure fluctuation. The transducers of absolute and pressure differential of this type can be used in automated systems of life activity. The high sensitivity of string transducers to pressure exceeding 100 hertz/mm (water column) permits to use them in devices for measuring gas concentration. The combination of optical and deformation methods of measurements forms the basis of their operation. The pressure change occurs due to the fact that gas molecules absorbing the quanta of incident light, become at excited state and then excitation energy of their vibrational-rotatory degrees of freedom converts to the energy of translational motion of molecules, i.e. to heat appropriate to pressure increase. Using these tens converters of high pressure one can prevent the possible accidents on oil pipe-like Baku-Tibilisi-Ceyhan

Design of Diaphragm Based MEMS Pressure Sensor with Sensitivity Analysis for Environmental Applications

Directory of Open Access Journals (Sweden)

A. Nallathambi

2015-05-01

Full Text Available In this paper Micro-electromechanical System (MEMS diaphragm based pressure sensor for environmental applications is discussed. The main focus of this paper is to design, simulate and analyze the sensitivity of MEMS based diaphragm using different structures to measure the low and high pressure values. The simulation is done through the finite element tool and specifications related the maximum convinced stress; deflection and sensitivity of the diaphragms have been analyzed using the software INTELLISUITE 8.7v. The change in pressure is to bending of the diaphragm that modifies the measured displacement between the substrate and the diaphragm. This change in displacement gives the measure of the pressure in that environment. The design of these studies can be used to improve the sensitivity of these devices. Here the diaphragm based pressure sensor produced better displacement, sensitivity and stress output responses are obtained from the square diaphragm. The pressure range from 0.6 MPa to 25 MPa and its maximum displacement is accordingly 59 mm over a pressure range of 0 to 2 MPa. Its sensitivity is therefore 2.35 [10E-12/Pa].

A cryogenic multichannel electronically scanned pressure module

Science.gov (United States)

Shams, Qamar A.; Fox, Robert L.; Adcock, Edward E.; Kahng, Seun K.

1992-01-01

Consideration is given to a cryogenic multichannel electronically scanned pressure (ESP) module developed and tested over an extended temperature span from -184 to +50 C and a pressure range of 0 to 5 psig. The ESP module consists of 32 pressure sensor dice, four analog 8 differential-input multiplexers, and an amplifier circuit, all of which are packaged in a physical volume of 2 x 1 x 5/8 in with 32 pressure and two reference ports. Maximum nonrepeatability is measured at 0.21 percent of full-scale output. The ESP modules have performed consistently well over 15 times over the above temperature range and continue to work without any sign of degradation. These sensors are also immune to repeated thermal shock tests over a temperature change of 220 C/sec.

Superconductivity of divalent Chevrel phases at very high pressures

International Nuclear Information System (INIS)

Yao, Y.S.; Guertin, R.P.; Hinks, D.G.; Jorgensen, J.; Capone II, D.W.

1988-01-01

The electrical resistivity and the superconducting transition temperatures were examined for three representative divalent Chevrel phase systems, SnMo 6 S 8 , EuMo 6 S 8 , and BaMo 6 S 8 , as a function of hydrostatic pressure to 2 GPa and in quasihydrostatic pressures to 10 GPa. In all systems, T/sub c/ is depressed to 0 K for sufficiently large pressures. For the Sn- and Eu-based systems, both highly purified samples and samples with controlled oxygen content were used. In an oxygenated SnMo 6 S 8 sample (less than 3% O 2 substituted for the S atoms) the pressure threshold and maximum T/sub c/ are 40% lower than in the pure sample, but for P>3.5 GPa the T/sub c/-P phase diagrams nearly coincide, with T/sub c/ reaching zero at an extrapolated pressure of about 12 GPa. In pure EuMo 6 S 8 , superconductivity appears only above a threshold pressure of about 1 GPa and is depressed to 0 K above 4.5 GPa. In an oxygenated sample the maximum T/sub c/ and the threshold pressure are depressed, and above about 3.5 GPa the T/sub c/-P phase diagrams coincide, as in the Sn-based system, although T/sub c/ is then rapidly depressed to 0 K at about 4.5 GPa. In a highly purified BaMo 6 S 8 sample superconductivity appears above about 2 GPa and is depressed to 0 K at extrapolated pressures above 12 GPa. A full transition to the zero-resistance superconducting state is observed in BaMo 6 S 8 . The data are discussed in terms of a model linking the rhombohedral-to-triclinic structural transition, the superconducting transition temperature, and the role of pressure in suppressing the structural transition

Theory and application of maximum magnetic energy in toroidal plasmas

International Nuclear Information System (INIS)

Chu, T.K.

1992-02-01

The magnetic energy in an inductively driven steady-state toroidal plasma is a maximum for a given rate of dissipation of energy (Poynting flux). A purely resistive steady state of the piecewise force-free configuration, however, cannot exist, as the periodic removal of the excess poloidal flux and pressure, due to heating, ruptures the static equilibrium of the partitioning rational surfaces intermittently. The rupture necessitates a plasma with a negative q'/q (as in reverse field pinches and spheromaks) to have the same α in all its force-free regions and with a positive q'/q (as in tokamaks) to have centrally peaked α's

High cost of stage IV pressure ulcers.

Science.gov (United States)

Brem, Harold; Maggi, Jason; Nierman, David; Rolnitzky, Linda; Bell, David; Rennert, Robert; Golinko, Michael; Yan, Alan; Lyder, Courtney; Vladeck, Bruce

2010-10-01

The aim of this study was to calculate and analyze the cost of treatment for stage IV pressure ulcers. A retrospective chart analysis of patients with stage IV pressure ulcers was conducted. Hospital records and treatment outcomes of these patients were followed up for a maximum of 29 months and analyzed. Costs directly related to the treatment of pressure ulcers and their associated complications were calculated. Nineteen patients with stage IV pressure ulcers (11 hospital-acquired and 8 community-acquired) were identified and their charts were reviewed. The average hospital treatment cost associated with stage IV pressure ulcers and related complications was $129,248 for hospital-acquired ulcers during 1 admission, and $124,327 for community-acquired ulcers over an average of 4 admissions. The costs incurred from stage IV pressure ulcers are much greater than previously estimated. Halting the progression of early stage pressure ulcers has the potential to eradicate enormous pain and suffering, save thousands of lives, and reduce health care expenditures by millions of dollars. Copyright © 2010 Elsevier Inc. All rights reserved.

Variation with Mach Number of Static and Total Pressures Through Various Screens

Science.gov (United States)

Adler, Alfred A

1946-01-01

Tests were conducted in the Langley 24-inch highspeed tunnel to ascertain the static-pressure and total-pressure losses through screens ranging in mesh from 3 to 12 wires per inch and in wire diameter from 0.023 to 0.041 inch. Data were obtained from a Mach number of approximately 0.20 up to the maximum (choking) Mach number obtainable for each screen. The results of this investigation indicate that the pressure losses increase with increasing Mach number until the choking Mach number, which can be computed, is reached. Since choking imposes a restriction on the mass rate of flow and maximum losses are incurred at this condition, great care must be taken in selecting the screen mesh and wire dimmeter for an installation so that the choking Mach number is

Energy and impacts of pressure vessel explosions

International Nuclear Information System (INIS)

Kurttila, H.

1999-01-01

In this paper the explosion energy is considered to be same as the energy of pressure vessel discharge. This is the maximum energy which can be obtained from the process. The energy can be used or it can cause the violence of an explosion accident. (orig.)

Acoustic conditions in open plan offices – Pilot test results

Directory of Open Access Journals (Sweden)

Witold Mikulski

2016-10-01

Full Text Available Background: The main source of noise in open plan office are conversations. Office work standards in such premises are attained by applying specific acoustic adaptation. This article presents the results of pilot tests and acoustic evaluation of open space rooms. Material and Methods: Acoustic properties of 6 open plan office rooms were the subject of the tests. Evaluation parameters, measurement methods and criterial values were adopted according to the following standards: PN-EN ISO 3382- 3:2012, PN-EN ISO 3382-2:2010, PN-B-02151-4:2015-06 and PN-B-02151-3:2015-10. Results: The reverberation time was 0.33– 0.55 s (maximum permissible value in offices – 0.6 s; the criterion was met, sound absorption coefficient in relation to 1 m2 of the room’s plan was 0.77–1.58 m2 (minimum permissible value – 1.1 m2; 2 out of 6 rooms met the criterion, distraction distance was 8.5–14 m (maximum permissible value – 5 m; none of the rooms met the criterion, A-weighted sound pressure level of speech at a distance of 4 m was 43.8–54.7 dB (maximum permissible value – 48 dB; 2 out of 6 rooms met the criterion, spatial decay rate of the speech was 1.8–6.3 dB (minimum permissible value – 7 dB; none of the rooms met the criterion. Conclusions: Standard acoustic treatment, containing sound absorbing suspended ceiling, sound absorbing materials on the walls, carpet flooring and sound absorbing workplace barriers, is not sufficient. These rooms require specific advanced acoustic solutions. Med Pr 2016;67(5:653–662

Optimal Control as a method for Diesel engine efficiency assessment including pressure and NO_x constraints

International Nuclear Information System (INIS)

Guardiola, Carlos; Climent, Héctor; Pla, Benjamín; Reig, Alberto

2017-01-01

Highlights: • Optimal Control is applied for heat release shaping in internal combustion engines. • Optimal Control allows to assess the engine performance with a realistic reference. • The proposed method gives a target heat release law to define control strategies. - Abstract: The present paper studies the optimal heat release law in a Diesel engine to maximise the indicated efficiency subject to different constraints, namely: maximum cylinder pressure, maximum cylinder pressure derivative, and NO_x emission restrictions. With this objective, a simple but also representative model of the combustion process has been implemented. The model consists of a 0D energy balance model aimed to provide the pressure and temperature evolutions in the high pressure loop of the engine thermodynamic cycle from the gas conditions at the intake valve closing and the heat release law. The gas pressure and temperature evolutions allow to compute the engine efficiency and NO_x emissions. The comparison between model and experimental results shows that despite the model simplicity, it is able to reproduce the engine efficiency and NO_x emissions. After the model identification and validation, the optimal control problem is posed and solved by means of Dynamic Programming (DP). Also, if only pressure constraints are considered, the paper proposes a solution that reduces the computation cost of the DP strategy in two orders of magnitude for the case being analysed. The solution provides a target heat release law to define injection strategies but also a more realistic maximum efficiency boundary than the ideal thermodynamic cycles usually employed to estimate the maximum engine efficiency.

Wind pressure loading for tall buidings: a case study of Warsaw Trade Tower

CSIR Research Space (South Africa)

Cwik, M

2012-12-01

Full Text Available of the building model and its surroundings, as well as the testing methods are described. The second part provides a description of the evaluation of the extreme pressure values using Gumbel distribution. Minimum and maximum wind pressure patterns over facade...

High-Pressure Polymorphism in Orthoamphiboles

Science.gov (United States)

Finkelstein, G. J.; Zhang, D.; Shelton, H.; Dera, P.

2017-12-01

Amphiboles are double-chain silicate minerals that are the structurally hydrated counterpart to single-chain, anhydrous pyroxenes. They may play an important role in the earth as a carrier for volatiles in subduction zones, as well as a generator for seismic anisotropy in the upper mantle. Recent work has described previously unrecognized high-pressure polymorphism at low temperatures in a variety of pyroxene minerals, which may be relevant for the structure and dynamics of thick, cold, subducted slabs. However, high-pressure polymorphism in amphiboles above a few GPa in pressure has not been well explored, and if similar polymorphism to pyroxenes exists in this mineral family, it may affect the extent and depth of volatile transport in amphiboles, as well as their rheological properties. At low temperatures and high pressures, orthopyroxenes undergo crystal structure transitions at lower pressures than clinopyroxenes (10-30 GPa vs. > 50 GPa), so for this study we have investigated polymorphism in the anthophyllite-gedrite (Al-free and Al rich) orthoamphibole solid solution series. Using neon gas-loaded diamond anvil cells, we compressed both phases to a maximum pressure of 31 GPa, and observed transitions to new monoclinic structures in both endmembers. In this presentation, we will discuss the details of these transitions and implications for the earth's interior.

N Reactor pressure tube 2566 postirradiation examination

International Nuclear Information System (INIS)

Scott, K.V.

1978-01-01

Pressure tube 2566 was removed from N Reactor in July, 1977 to initiate the postirradiation examination program required by the Technical Specifications. Destructive examination of the pressure tube, after a maximum accumulated fluence of 4.6 x 10 21 n/cm 2 (E > 1 MeV), was conducted at the Hanford Engineering Development Laboratory to determine the effects of reactor service on the mechanical properties and hydrogen absorption and corrosion characteristics of the pressure tube. Tube 2566 is the sixth tube removed for destructive examination since the initial reactor startup. Evaluation of test results reveal that no significant detrimental changes have occurred in the parameters studied, since the last tube was removed in 1974

A simple in-surge pressure analysis using the SPACE code

International Nuclear Information System (INIS)

Youn, Bum Soo; Kim, Yo Han; Lee, Dong Hyuk; Yang, Chang Keun; Kim, Se Yun; Ha, Sang Jun

2010-01-01

Currently, nuclear safety analysis codes used in Korea are developed by all the overseas. These codes are paying huge fee and permission must be obtained for use in the country. In addition, orders for nuclear power plants must ensure the safety analysis code for independent domestic technology. Therefore, Korea Electric Power Research Institute(KEPRI) is developing the domestic nuclear power safety analysis, SPACE(Safety and Performance Analysis Code for nuclear power plants). To determine the computational power of pressurizer model in development SPACE code, it was compared with existing commercial nuclear power safety analysis code, RETRAN

Experimental and finite element prediction of bursting pressure in compound cylinders

International Nuclear Information System (INIS)

Majzoobi, G.H.; Farrahi, G.H.; Pipelzadeh, M.K.; Akbari, A.

2004-01-01

Aluminium cylinders with a constant ratio of outer to inner radii, k=2.2, with different diametral interferences and various shrinkage radii were subjected to bursting and autofrettage pressures. Numerical simulations of the compound cylinders were also performed using the finite element code, NISA. The results can predict the optimum shrinkage radius to a reasonable accuracy with the use of finite element analysis. This radius corresponds to the situation when the maximum von-Mises stress at the internal radii of both the inner and outer cylinders become equal. It was shown that the maximum von-Mises stress across the wall of the cylinder is at the minimum at this shrinkage radius. The optimum diametral interference was found to be that which sufficiently brought the contact surface of the inner and outer cylinders to the point of yielding. Should the shrinkage pressure exceed the elastic limit, the pressure capacity of the cylinder will not be improved. The numerical and experimental results show that autofrettage had no effect on the bursting pressure of the thick-walled compound cylinder for the material tested

Maximum Acceleration Recording Circuit

Science.gov (United States)

Bozeman, Richard J., Jr.

1995-01-01

Coarsely digitized maximum levels recorded in blown fuses. Circuit feeds power to accelerometer and makes nonvolatile record of maximum level to which output of accelerometer rises during measurement interval. In comparison with inertia-type single-preset-trip-point mechanical maximum-acceleration-recording devices, circuit weighs less, occupies less space, and records accelerations within narrower bands of uncertainty. In comparison with prior electronic data-acquisition systems designed for same purpose, circuit simpler, less bulky, consumes less power, costs and analysis of data recorded in magnetic or electronic memory devices. Circuit used, for example, to record accelerations to which commodities subjected during transportation on trucks.

Neutron spectra unfolding with maximum entropy and maximum likelihood

International Nuclear Information System (INIS)

Itoh, Shikoh; Tsunoda, Toshiharu

1989-01-01

A new unfolding theory has been established on the basis of the maximum entropy principle and the maximum likelihood method. This theory correctly embodies the Poisson statistics of neutron detection, and always brings a positive solution over the whole energy range. Moreover, the theory unifies both problems of overdetermined and of underdetermined. For the latter, the ambiguity in assigning a prior probability, i.e. the initial guess in the Bayesian sense, has become extinct by virtue of the principle. An approximate expression of the covariance matrix for the resultant spectra is also presented. An efficient algorithm to solve the nonlinear system, which appears in the present study, has been established. Results of computer simulation showed the effectiveness of the present theory. (author)

Maximum Power from a Solar Panel

Directory of Open Access Journals (Sweden)

Michael Miller

2010-01-01

Full Text Available Solar energy has become a promising alternative to conventional fossil fuel sources. Solar panels are used to collect solar radiation and convert it into electricity. One of the techniques used to maximize the effectiveness of this energy alternative is to maximize the power output of the solar collector. In this project the maximum power is calculated by determining the voltage and the current of maximum power. These quantities are determined by finding the maximum value for the equation for power using differentiation. After the maximum values are found for each time of day, each individual quantity, voltage of maximum power, current of maximum power, and maximum power is plotted as a function of the time of day.

Thermo hydraulic analysis of narrow channel effect in supercritical-pressure light water reactor

International Nuclear Information System (INIS)

Zhou Tao; Chen Juan; Cheng Wanxu

2012-01-01

Highlights: ► Detailed thermal analysis with different narrow gaps between fuel rods is given. ► Special characteristics of narrow channels effect on heat transfer in supercritical pressure are shown. ► Reasonable size selection of gaps between fuel rods is proposed for SCWR. - Abstract: The size of the gap between fuel rods has important effects on flow and heat transfer in a supercritical-pressure light water reactor. Based on thermal analysis at different coolant flow rates, the reasonable value range of gap size between fuel rods is obtained, for which the maximum cladding temperature safety limits and installation technology are comprehensively considered. Firstly, for a given design flow rate of coolant, thermal hydraulic analysis of supercritical pressure light water reactor with different gap sizes is provided by changing the fuel rod pitch only. The results show that, by means of reducing the gap size between fuel rods, the heat transfer coefficients between coolant and fuel rod, as well as the heat transfer coefficient between coolant and water rod, would both increase noticeably. Furthermore, the maximum cladding temperature will significantly decrease when the moderator temperature is decreased but coolant temperature remains essentially constant. Meanwhile, the reduction in the maximum cladding temperature in the inner assemblies is much larger than that in the outer assemblies. In addition, the maximum cladding temperature could be further reduced by means of increasing coolant flow rate for each gap size. Finally, the characteristics of narrow channels effect are proposed, and the maximum allowable gap between fuel rods is obtained by making full use of the enhancing narrow channels effect on heat transfer, and concurrently considering installation. This could provide a theoretical reference for supercritical-pressure light water reactor design optimization, in which the effects of gap size and flow rate on heat transfer are both considered.

High pressure inactivation of relevant target microorganisms in poultry meat products and the evaluation of pressure-induced protein denaturation of marinated poultry under different high pressure treatments

Science.gov (United States)

Schmidgall, Johanna; Hertel, Christian; Bindrich, Ute; Heinz, Volker; Toepfl, Stefan

2011-03-01

In this study, the possibility of extending shelf life of marinated poultry meat products by high pressure processing was evaluated. Relevant spoilage and pathogenic strains were selected and used as target microorganisms (MOs) for challenge experiments. Meat and brine were inoculated with MOs and treated at 450 MPa, 4 °C for 3 min. The results of inactivation show a decreasing pressure tolerance in the series Lactobacillus > Arcobacter > Carnobacterium > Bacillus cereus > Brochothrix thermosphacta > Listeria monocytogenes. Leuconostoc gelidum exhibited the highest pressure tolerance in meat. A protective effect of poultry meat was found for L. sakei and L. gelidum. In parallel, the influence of different marinade formulations (pH, carbonates, citrates) on protein structure changes during a pressure treatment was investigated. Addition of sodium carbonate shows a protection against denaturation of myofibrillar proteins and provides a maximum water-holding capacity. Caustic marinades allowed a higher retention of product characteristics than low-pH marinades.

High pressure experimental water loop; Cellule experimentale a eau sous pression

Energy Technology Data Exchange (ETDEWEB)

Grenon, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Terny, M [Societe Grenobloise d' Etudes et d' Applications Hydrauliques, 38 (France)

1958-07-01

A high pressure experimental water loop has been made for studying the detection and evolution of cladding failure in a pressurized reactor. The loop has been designed for a maximum temperature of 360 deg. C, a maximum of 160 kg/cm{sup 2} and flow rates up to 5 m{sup 3}/h. The entire loop consists of several parts: a main circuit with a canned rotor circulation pump, steam pressurizer, heating tubes, two hydro-cyclones (one de-gasser and one decanter) and one tubular heat exchanger; a continuous purification loop, connected in parallel, comprising pressure reducing valves and resin pots which also allow studies of the stability of resins under pressure, temperature and radiation; following the gas separator is a gas loop for studying the recombination of the radiolytic gases in the steam phase. The preceding circuits, as well as others, return to a low pressure storage circuit. The cold water of the low pressure storage flask is continuously reintroduced into the high pressure main circuit by means of a return pump at a maximum head of 160 kg /cm{sup 2}, and adjusted to the pressurizer level. This loop is also a testing bench for the tight high pressure apparatus. The circulating pump and the connecting flanges (Oak Ridge type) are water-tight. The feed pump and the pressure reducing valves are not; the un-tight ones have a system of leak recovery. To permanently check the tightness the circuit has been fitted with a leak detection system (similar to the HRT one). (author)Fren. [French] Une cellule experimentale a eau sous pression a ete realisee pour l'etude de l'evolution et de la detection de ruptures de gaines dans le cas d'un reacteur pressurise. Les performances de ce circuit sont: 350 deg. C maximum pour la temperature et 160 kg/cm{sup 2} maximum pour la pression, le debit pouvant atteindre 5 m{sup 3}/h. Le circuit complet est constitue de plusieurs parties: un circuit principal avec pompe de circulation a rotor immerge, preiseur a vapeur, tubes chaudieres

Permissive Attitude toward LGBT in Jakarta: Study of Differences in the Level of Permissiveness among individuals born in 1950-1970’s and 1980-2000’s

Directory of Open Access Journals (Sweden)

Setiowati Endang

2017-01-01

Full Text Available Lesbian, Gay, Bisexual and Transgender (LGBT movement is strongly resisted in Indonesia. This is not only that Indonesian people are still religious, but also the traditional norms and values are still very strong in daily life. Based on the Pew Research Centre in 2014, the homosexuality level of acceptance in Indonesia is only about 3%, while the rejection is 93%. LGBT has been started since the 1960s, but it became strength since the private television in early 1990s promoted the effeminate characters to be the top celebrities paid hundreds of millions of rupiah. People who born in the 1950s to 1970s that consume only one TV station will have different respond to LGBT with people who born in the 1980s to 2000s with some TV stations. Purpose: to look for the differences in the level of permissiveness toward homosexuality between those two groups of people. Method: using a mix method of qualitative and quantitative. Qualitative methods interviewed 6 informants. The quantitative will be a survey of 100 respondents. Result: The level of permissiveness on LGBT of the younger group is higher than the older group. According to acceptance factor both group mostly reject LGBT. But according to properness, the older group tend to say disturbing and disgusting, while for the younger group assume not disturbing.

Relationship Between 24-Hour Ambulatory Blood Pressure and Cognitive Function in Community-Living Older Adults: The UCSD Ambulatory Blood Pressure Study.

Science.gov (United States)

Conway, Kyle S; Forbang, Nketi; Beben, Tomasz; Criqui, Michael H; Ix, Joachim H; Rifkin, Dena E

2015-12-01

Twenty-four-hour ambulatory blood pressure (BP) patterns have been associated with diminished cognitive function in hypertensive and very elderly populations. The relationship between ambulatory BP patterns and cognitive function in community-living older adults is unknown. We conducted a cross-sectional study in which 24-hour ambulatory BP, in-clinic BP, and cognitive function measures were obtained from 319 community-living older adults. The mean age was 72 years, 66% were female, and 13% were African-American. We performed linear regression with performance on the Montreal Cognitive Assessment (MoCA) as the primary outcome and 24-hour BP patterns as the independent variable, adjusting for age, sex, race/ethnicity, education, and comorbidities. Greater nighttime systolic dipping (P = 0.046) and higher 24-hour diastolic BP (DBP; P = 0.015) were both significantly associated with better cognitive function, whereas 24-hour systolic BP (SBP), average real variability, and ambulatory arterial stiffness were not. Higher 24-hour DBP and greater nighttime systolic dipping were significantly associated with improved cognitive function. Future studies should examine whether low 24-hour DBP and lack of nighttime systolic dipping predict future cognitive impairment. © American Journal of Hypertension, Ltd 2015. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

The regulations for enforcing the law concerning prevention from radiation hazards due to radioisotopes

International Nuclear Information System (INIS)

1978-01-01

These provisions are established on the basis of and to enforce the ''Law for the prevention of radiation hazards due to radioisotopes'' and the Enforcement Order for the ''Law concerning the prevention of radiation hazards due to radioisotopes''. The Regulation includes the definitions of terms, applications for the permission of the use of radioisotopes, standards on usage, obligation of measurement, persons in charge of radiation, etc. Terms are explained, such as persons engaging in radiation works, persons who enter at any time the control areas, radiation facilities, maximum permissible exposure dose, cumulative dose, maximum permissible cumulative dose, maximum permissible concentration in the air, maximum permissible concentration in water and maximum permissible surface density. The applications for permission in written forms are required for the use, sale and abandonment of radioisotopes. Radioisotopes or the apparatuses for generating radiation shall be used in the using facilities. The measurement of radiation dose rate, particle flux density and contamination due to radioisotopes shall be made with radiation-measuring instruments. At least one person shall be chosen as the chief radiation-handling person in each factory, establishment, selling office or abandoning establishment by a user, a trademan or a person engaged in abandonment of radioisotopes. The forms for the application for permission, etc. are attached. (Okada, K.)

Tibiofemoral joint contact area and pressure after single- and double-bundle anterior cruciate ligament reconstruction.

Science.gov (United States)

Morimoto, Yusuke; Ferretti, Mario; Ekdahl, Max; Smolinski, Patrick; Fu, Freddie H

2009-01-01

The purpose of this study was to compare the tibiofemoral contact area and pressure after single-bundle (SB) and double-bundle (DB) anterior cruciate ligament (ACL) reconstruction by use of 2 femoral and 2 tibial tunnels in intact cadaveric knees. Tibiofemoral contact area and mean and maximum pressures were measured by pressure-sensitive film (Fujifilm, Valhalla, NY) inserted between the tibia and femur. The knee was subjected to a 1,000-N axial load by use of a uniaxial testing machine at 0 degrees , 15 degrees , 30 degrees , and 45 degrees of flexion. Three conditions were evaluated: (1) intact ACL, (2) SB ACL reconstruction (n = 10 knees), and (3) DB ACL reconstruction (n = 9 knees). When compared with the intact knee, DB ACL reconstruction showed no significant difference in tibiofemoral contact area and mean and maximum pressures. SB ACL reconstruction had a significantly smaller contact area on the lateral and medial tibiofemoral joints at 30 degrees and 15 degrees of flexion. SB ACL reconstruction also had significantly higher mean pressures at 15 degrees of flexion on the medial tibiofemoral joint and at 0 degrees and 15 degrees of flexion on the lateral tibiofemoral joint, as well as significantly higher maximum pressures at 15 degrees of flexion on the lateral tibiofemoral joint. SB ACL reconstruction resulted in a significantly smaller tibiofemoral contact area and higher pressures. DB ACL more closely restores the normal contact area and pressure mainly at low flexion angles. Our findings suggest that the changes in the contact area and pressures after SB ACL reconstruction may be one of the causes of osteoarthritis on long-term follow-up. DB ACL reconstruction may reduce the incidence of osteoarthritis by closely restoring contact area and pressure.

Optimal design of the gerotor (2-ellipses) for reducing maximum contact stress

Energy Technology Data Exchange (ETDEWEB)

Kwak, Hyo Seo; Li, Sheng Huan [Dept. of Mechanical Convergence Technology, Pusan National University, Busan (Korea, Republic of); Kim, Chul [School of Mechanical Design and Manufacturing, Busan Institute of Science and Technology, Busan (Korea, Republic of)

2016-12-15

The oil pump, which is used as lubricator of engines and auto transmission, supplies working oil to the rotating elements to prevent wear. The gerotor pump is used widely in the automobile industry. When wear occurs due to contact between an inner rotor and an outer rotor, the efficiency of the gerotor pump decreases rapidly, and elastic deformation from the contacts also causes vibration and noise. This paper reports the optimal design of a gerotor with a 2-ellipses combined lobe shape that reduces the maximum contact stress. An automatic program was developed to calculate Hertzian contact stress of the gerotor using the Matlab and the effect of the design parameter on the maximum contact stress was analyzed. In addition, the method of theoretical analysis for obtaining the contact stress was verified by performing the fluid-structural coupled analysis using the commercial software, Ansys, considering both the driving force of the inner rotor and the fluid pressure, which is generated by working oil.

Recombinant pestivirus E2 glycoproteins prevent viral attachment to permissive and non permissive cells with different efficiency.

Science.gov (United States)

Asfor, A S; Wakeley, P R; Drew, T W; Paton, D J

2014-08-30

Bovine viral diarrhoea virus (BVDV) is an economically important animal pathogen, which like other pestiviruses has similar molecular biological features to hepaciviruses, including human Hepatitis C virus. The pestivirus E2 glycoproteins are the major target for virus-neutralising antibodies, as well as playing a role in receptor binding and host range restriction. In this study, recombinant E2 glycoproteins (rE2) derived from three different pestivirus species were examined for their inhibitory effects on pestivirus infectivity in cell culture. Histidine-tagged rE2 glycoproteins of BVDV type 2 strain 178003, BVDV type 1 strain Oregon C24V and CSFV strain Alfort 187 were produced in Spodoptera frugiperda insect cells and purified under native conditions. The ability of rE2 glycoprotein to inhibit the infection of permissive cells by both homologous and heterologous virus was compared, revealing that the inhibitory effects of rE2 glycoproteins correlated with the predicted similarity of the E2 structures in the recombinant protein and the test virus. This result suggests that the sequence and structure of E2 are likely to be involved in the host specificity of pestiviruses at their point of uptake into cells. Copyright © 2014 Elsevier B.V. All rights reserved.

MEMS pressure sensor with maximum performances by using novel back-side direct-exposure concept featuring through glass vias

Science.gov (United States)

Mukhopadhyay, B.; Fritz, M.; Mackowiak, P.; Vu, T. C.; Ehrmann, O.; Lang, K.-D.; Ngo, H.-D.

2013-05-01

Design, simulation, fabrication, and characterization of novel MEMS pressure sensors with new back-side-direct-exposure packaging concept are presented. The sensor design is optimized for harsh environments e.g. space, military, offshore and medical applications. Unbreakable connection between the active side of the Si-sensor and the protecting glass capping was realized by anodic bonding using a thin layer of metal. To avoid signal corruption of the measured pressure caused by an encapsulation system, the media has direct contact to the backside of the Si membrane and can deflect it.

The influence of thermal pressure on equilibrium models of hypermassive neutron star merger remnants

Energy Technology Data Exchange (ETDEWEB)

Kaplan, J. D.; Ott, C. D.; Roberts, L. [TAPIR, California Institute of Technology, Mailcode 350-17, Pasadena, CA 91125 (United States); O' Connor, E. P. [CITA, University of Toronto, 60 St. George Street, Toronto, ON M5S 3H8 (Canada); Kiuchi, K. [Yukawa Institute for Theoretical Physics, University of Kyoto, Kyoto (Japan); Duez, M., E-mail: cott@tapir.caltech.edu [Department of Physics and Astronomy, Washington State University, Pullman, WA (United States)

2014-07-20

The merger of two neutron stars leaves behind a rapidly spinning hypermassive object whose survival is believed to depend on the maximum mass supported by the nuclear equation of state (EOS), angular momentum redistribution by (magneto-)rotational instabilities, and spindown by gravitational waves. The high temperatures (∼5-40 MeV) prevailing in the merger remnant may provide thermal pressure support that could increase its maximum mass and, thus, its life on a neutrino-cooling timescale. We investigate the role of thermal pressure support in hypermassive merger remnants by computing sequences of spherically symmetric and axisymmetric uniformly and differentially rotating equilibrium solutions to the general-relativistic stellar structure equations. Using a set of finite-temperature nuclear EOS, we find that hot maximum-mass critically spinning configurations generally do not support larger baryonic masses than their cold counterparts. However, subcritically spinning configurations with mean density of less than a few times nuclear saturation density yield a significantly thermally enhanced mass. Even without decreasing the maximum mass, cooling and other forms of energy loss can drive the remnant to an unstable state. We infer secular instability by identifying approximate energy turning points in equilibrium sequences of constant baryonic mass parameterized by maximum density. Energy loss carries the remnant along the direction of decreasing gravitational mass and higher density until instability triggers collapse. Since configurations with more thermal pressure support are less compact and thus begin their evolution at a lower maximum density, they remain stable for longer periods after merger.

The influence of thermal pressure on equilibrium models of hypermassive neutron star merger remnants

International Nuclear Information System (INIS)

Kaplan, J. D.; Ott, C. D.; Roberts, L.; O'Connor, E. P.; Kiuchi, K.; Duez, M.

2014-01-01

The merger of two neutron stars leaves behind a rapidly spinning hypermassive object whose survival is believed to depend on the maximum mass supported by the nuclear equation of state (EOS), angular momentum redistribution by (magneto-)rotational instabilities, and spindown by gravitational waves. The high temperatures (∼5-40 MeV) prevailing in the merger remnant may provide thermal pressure support that could increase its maximum mass and, thus, its life on a neutrino-cooling timescale. We investigate the role of thermal pressure support in hypermassive merger remnants by computing sequences of spherically symmetric and axisymmetric uniformly and differentially rotating equilibrium solutions to the general-relativistic stellar structure equations. Using a set of finite-temperature nuclear EOS, we find that hot maximum-mass critically spinning configurations generally do not support larger baryonic masses than their cold counterparts. However, subcritically spinning configurations with mean density of less than a few times nuclear saturation density yield a significantly thermally enhanced mass. Even without decreasing the maximum mass, cooling and other forms of energy loss can drive the remnant to an unstable state. We infer secular instability by identifying approximate energy turning points in equilibrium sequences of constant baryonic mass parameterized by maximum density. Energy loss carries the remnant along the direction of decreasing gravitational mass and higher density until instability triggers collapse. Since configurations with more thermal pressure support are less compact and thus begin their evolution at a lower maximum density, they remain stable for longer periods after merger.

Outcome of TVT operations in women with low maximum urethral closure pressure.

Science.gov (United States)

Moe, Kjartan; Schiøtz, Hjalmar A; Kulseng-Hanssen, Sigurd

2017-06-01

(i) To establish whether low maximal urethral closure pressure (MUCP) is associated with a poorer prognosis after TVT-surgery, and if so to establish an MUCP cut-off value for poor outcome. (ii) To characterize the population with a low MUCP. Retrospective analysis of data from 6,646 women with stress/mixed urinary incontinence included in the Norwegian Female Incontinence Registry. Postoperative subjective (degree of satisfaction), objective (leakage on stress test) and composite cure according to preoperative MUCP were analyzed in unadjusted and adjusted analysis. Preoperative variables were compared between women having a low or normal MUCP. Non-parametric tests were used on continuous variables and χ 2 tests on categorical variables. Logistic regression was used for the adjusted analysis. Level of significance: P 20 cm H 2 O. In adjusted analysis MUCP ≤20 cm H 2 O was associated with neither objective, subjective, nor composite failure. Women with MUCP TVT-surgery compared to women with MUCP >20 cm H 2 O after adjusting for preoperative variables. Neurourol. Urodynam. 36:1320-1324, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Influence of Exercise Modality on Cerebral-Ocular Hemodynamics and Pressures

Science.gov (United States)

Scott, J.; Martin, D.; Crowell, B.; Goetchius, E.; Seponski, C.; Gonzales, R.; Matz, T.; Ploutz-Snyder, R.; Stenger, M.; Ploutz-Snyder, L.

2016-01-01

Background: Moderate and high intensity aerobic or resistance exercise has clearly identified benefits for cardiac, muscle, and bone health. However, the impact of such exercise - either as a mitigating or an exacerbating factor - on the development of the visual impairment and intracranial pressure syndrome (VIIP) is unknown. Accordingly, our aim was to characterize the effect of an acute bout of resistance (RE), moderate-intensity continuous (CE), and high-intensity interval exercise (IE) during a cephalad fluid shift on cerebral-ocular hemodynamics and pressures. Methods: 10 male subjects (36 plus or minus 9 years) completed 4 testing days in a 15 degree head-down tilt (HDT): (1) assessment of maximum volume of O (sub 2), (2) RE session (4 sets of 12 repetition maximum leg press exercise), (3) CE session (30 minutes of cycling at 60 percent maximum volume of O (sub 2)), and (4) IE session (4 by 4-minute intervals of exercise at 85 percent maximum volume of O (sub 2) with 3-minute active rest periods). During each session, blood flow (Vivid-e, GE Healthcare) in extracranial arteries (common carotid artery, CCA; internal carotid artery, ICA; external carotid artery, ECA and vertebral artery, VA), and mean blood flow velocity in middle cerebral artery (MCA), internal jugular pressure (IJP; VeinPress), and intraocular pressure (IOP; Icare PRO) were measured at rest, at the end of each resistance or interval set, and every 5 minutes during continuous exercise. Translaminar pressure gradient (TLPG) was estimated by subtracting IJP from IOP. Results: There were no differences across days in pre-exercise resting blood flows or pressures. IOP decreased slightly from HDT rest (20.2 plus or minus 2.3 millimeters of mercury) to exercise (RE: 19.2 plus or minus 2.8 millimeters of mercury; CE: 18.9 plus or minus 3.2 millimeters of mercury; IE: 20.1 plus or minus 2.8 millimeters of mercury), while IJP decreased during CE (31.6 plus or minus 9.5 millimeters of mercury) and RE

Transcritical CO2 power cycle – Effects of regenerative heating using turbine bleed gas at intermediate pressure

International Nuclear Information System (INIS)

Mondal, Subha; De, Sudipta

2015-01-01

For energy utilization from low temperature waste heat, CO 2 is a potential working fluid due to its lower critical temperature. In this work, assuming finite quantity of flue gas available at low temperature (200 °C), a thermodynamic model is developed for a transcritical CO 2 power cycle utilizing turbine bleed gas for regenerative heating. Analysis show that the cycle performance improves with higher value of bleed ratio. However, for a specified bleed pressure and bleed gas temperature at the regenerator exit, maximum practical value of bleed ratio may be fixed by considering the exponential growth of the regenerator size (specified by NTU (number of transfer unit)). Most significant observation is the existence of optimum bleed pressures corresponding to maximum 1st law efficiency or minimum cycle irreversibility for specified values of remaining cycle parameters. - Highlights: • Thermodynamic model for Transcritical CO 2 cycle with bleed gas are developed. • Effects of bleed ratio, pressure, and regenerator exit gas temperature are studied. • 1st and 2nd law efficiencies are estimated. • An optimum bleed pressure for maximum 1st and 2nd efficiencies is obtained. • Maximum value of 1st law efficiency is limited by regenerator size

Physical Limits on Hmax, the Maximum Height of Glaciers and Ice Sheets

Science.gov (United States)

Lipovsky, B. P.

2017-12-01

The longest glaciers and ice sheets on Earth never achieve a topographic relief, or height, greater than about Hmax = 4 km. What laws govern this apparent maximum height to which a glacier or ice sheet may rise? Two types of answer appear possible: one relating to geological process and the other to ice dynamics. In the first type of answer, one might suppose that if Earth had 100 km tall mountains then there would be many 20 km tall glaciers. The counterpoint to this argument is that recent evidence suggests that glaciers themselves limit the maximum height of mountain ranges. We turn, then, to ice dynamical explanations for Hmax. The classical ice dynamical theory of Nye (1951), however, does not predict any break in scaling to give rise to a maximum height, Hmax. I present a simple model for the height of glaciers and ice sheets. The expression is derived from a simplified representation of a thermomechanically coupled ice sheet that experiences a basal shear stress governed by Coulomb friction (i.e., a stress proportional to the overburden pressure minus the water pressure). I compare this model to satellite-derived digital elevation map measurements of glacier surface height profiles for the 200,000 glaciers in the Randolph Glacier Inventory (Pfeffer et al., 2014) as well as flowlines from the Greenland and Antarctic Ice Sheets. The simplified model provides a surprisingly good fit to these global observations. Small glaciers less than 1 km in length are characterized by having negligible influence of basal melt water, cold ( -15C) beds, and high surface slopes ( 30 deg). Glaciers longer than a critical distance 30km are characterized by having an ice-bed interface that is weakened by the presence of meltwater and is therefore not capable of supporting steep surface slopes. The simplified model makes predictions of ice volume change as a function of surface temperature, accumulation rate, and geothermal heat flux. For this reason, it provides insights into

Energy harvesting from hydraulic pressure fluctuations

International Nuclear Information System (INIS)

Cunefare, K A; Skow, E A; Erturk, A; Savor, J; Verma, N; Cacan, M R

2013-01-01

State-of-the-art hydraulic hose and piping systems employ integral sensor nodes for structural health monitoring to avoid catastrophic failures. Energy harvesting in hydraulic systems could enable self-powered wireless sensor nodes for applications such as energy-autonomous structural health monitoring and prognosis. Hydraulic systems inherently have a high energy intensity associated with the mean pressure and flow. Accompanying the mean pressure is the dynamic pressure ripple, which is caused by the action of pumps and actuators. Pressure ripple is a deterministic source with a periodic time-domain behavior conducive to energy harvesting. An energy harvester prototype was designed for generating low-power electricity from pressure ripples. The prototype employed an axially-poled off-the-shelf piezoelectric stack. A housing isolated the stack from the hydraulic fluid while maintaining a mechanical coupling allowing for dynamic-pressure-induced deflection of the stack. The prototype exhibited an off-resonance energy harvesting problem since the fundamental resonance of the piezoelectric stack was much higher than the frequency content of the pressure ripple. The prototype was designed to provide a suitable power output for powering sensors with a maximum output of 1.2 mW. This work also presents electromechanical model simulations and experimental characterization of the piezoelectric power output from the pressure ripple in terms of the force transmitted into the harvester. (paper)

17 CFR 240.12f-1 - Applications for permission to reinstate unlisted trading privileges.

Science.gov (United States)

2010-04-01

... reinstate unlisted trading privileges. 240.12f-1 Section 240.12f-1 Commodity and Securities Exchanges... Rules and Regulations Under the Securities Exchange Act of 1934 Unlisted Trading § 240.12f-1 Applications for permission to reinstate unlisted trading privileges. (a) An application to reinstate unlisted...

42 CFR 433.67 - Limitations on level of FFP for permissible provider-related donations.

Science.gov (United States)

2010-10-01

... provider-related donations. 433.67 Section 433.67 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES... permissible provider-related donations. (a)(1) Limitations on bona fide donations. There are no limitations on the amount of bona fide provider-related donations that a State may receive without a reduction in FFP...

High-beta plasma effects in a low-pressure helicon plasma

International Nuclear Information System (INIS)

Corr, C. S.; Boswell, R. W.

2007-01-01

In this work, high-beta plasma effects are investigated in a low-pressure helicon plasma source attached to a large volume diffusion chamber. When operating above an input power of 900 W and a magnetic field of 30 G a narrow column of bright blue light (due to Ar II radiation) is observed along the axis of the diffusion chamber. With this blue mode, the plasma density is axially very uniform in the diffusion chamber; however, the radial profiles are not, suggesting that a large diamagnetic current might be induced. The diamagnetic behavior of the plasma has been investigated by measuring the temporal evolution of the magnetic field (B z ) and the plasma kinetic pressure when operating in a pulsed discharge mode. It is found that although the electron pressure can exceed the magnetic field pressure by a factor of 2, a complete expulsion of the magnetic field from the plasma interior is not observed. In fact, under our operating conditions with magnetized ions, the maximum diamagnetism observed is ∼2%. It is observed that the magnetic field displays the strongest change at the plasma centre, which corresponds to the maximum in the plasma kinetic pressure. These results suggest that the magnetic field diffuses into the plasma sufficiently quickly that on a long time scale only a slight perturbation of the magnetic field is ever observed

Process Factors Influence on Cavity Pressure Behavior in Microinjection Moulding

DEFF Research Database (Denmark)

Griffiths, C. A.; Dimov, S. S.; Scholz, S.

2011-01-01

about the filling behavior of different polymer melts. In this paper, a pressure sensor mounted inside a tool cavity was employed to analyse maximum cavity pressure, pressure increase rate during filling and pressure work. The influence of four mu IM parameters, melt temperature, mould temperature......Process monitoring of microinjection moulding (mu IM) is of crucial importance when analysing the effect of different parameter settings on the process and then in assessing its quality. Quality factors related to cavity pressure can provide valuable information about the process dynamics and also......, injection speed, and packing pressure on these three pressure-related process parameters was investigated. A design of experiment study was conducted by moulding a test part, a microfluidic component, in three different polymer materials, PP, ABS, and PC. The results show a similar process behavior for all...

Pressure effects on high temperature steam oxidation of Zircaloy-4

International Nuclear Information System (INIS)

Park, Kwangheon; Kim, Kwangpyo; Ryu, Taegeun

2000-01-01

The pressure effects on Zircaloy-4 (Zry-4) cladding in high temperature steam have been analyzed. A double layer autoclave was made for the high pressure, high temperature oxidation tests. The experimental test temperature range was 700 - 900 deg C, and pressures were 0.1 - 15 MPa. Steam partial pressure turns out to be an important one rather than total pressure. Steam pressure enhances the oxidation rate of Zry-4 exponentially. The enhancement depends on the temperature, and the maximum exists between 750 - 800 deg C. Pre-existing oxide layer decreases the enhancement about 40 - 60%. The acceleration of oxidation rate by high pressure team seems to be originated from the formation of cracks by abrupt transformation of tetragonal phase in oxide, where the un-stability of tetragonal phase comes from the reduction of surface energy by steam. (author)

Pressure Dependence of the Peierls Stress in Aluminum

Science.gov (United States)

Dang, Khanh; Spearot, Douglas

2018-03-01

The effect of pressure applied normal to the {111} slip plane on the Peierls stress in Al is studied via atomistic simulations. Edge, screw, 30°, and 60° straight dislocations are created using the Volterra displacement fields for isotropic elasticity. For each dislocation character angle, the Peierls stress is calculated based on the change in the internal energy, which is an invariant measure of the dislocation driving force. It is found that the Peierls stress for dislocations under zero pressure is in general agreement with previous results. For screw and 60° dislocations, the Peierls stress versus pressure relationship has maximum values associated with stacking fault widths that are multiples of the Peierls period. For the edge dislocation, the Peierls stress decreases with increasing pressure from tension to compression. Compared with the Mendelev potential, the Peierls stress calculated from the Mishin potential is more sensitive to changes in pressure.

Prototype Centralized Managing Permissions System Based on the Election Multibiometric Authentication

Directory of Open Access Journals (Sweden)

Alexey Nikolaevich Ruchay

2013-02-01

Full Text Available This work aims to develop a prototype system of centralized managing permissions based on the election multibiometric authentication. The novelty of this work is to develop the principles of distinction and multi-factor authentication, because at the moment there is no such development. Depending on various conditions and factors, including the availability of electronic means and convenience, resistance to attacks and exploits, disease or injury of users the biometric authentication can be selected on the basis of any such biometrics as rhythm password, voice, dynamic signatures and graphics recognition.

Method and system for gas flow mitigation of molecular contamination of optics

Science.gov (United States)

Delgado, Gildardo; Johnson, Terry; Arienti, Marco; Harb, Salam; Klebanoff, Lennie; Garcia, Rudy; Tahmassebpur, Mohammed; Scott, Sarah

2018-01-23

A computer-implemented method for determining an optimized purge gas flow in a semi-conductor inspection metrology or lithography apparatus, comprising receiving a permissible contaminant mole fraction, a contaminant outgassing flow rate associated with a contaminant, a contaminant mass diffusivity, an outgassing surface length, a pressure, a temperature, a channel height, and a molecular weight of a purge gas, calculating a flow factor based on the permissible contaminant mole fraction, the contaminant outgassing flow rate, the channel height, and the outgassing surface length, comparing the flow factor to a predefined maximum flow factor value, calculating a minimum purge gas velocity and a purge gas mass flow rate from the flow factor, the contaminant mass diffusivity, the pressure, the temperature, and the molecular weight of the purge gas, and introducing the purge gas into the semi-conductor inspection metrology or lithography apparatus with the minimum purge gas velocity and the purge gas flow rate.

Pressure-induced magnetic transition in CeP

International Nuclear Information System (INIS)

Naka, T.; Matsumoto, T.; Mori, N.; Okayama, Y.; Haga, Y.; Suzuki, T.

1997-01-01

Pressure dependence of magnetization in CeP is investigated up to 2 GPa. Multi-step transitions are induced by pressure. An antiferromagnetic transition at T N =11 K below 0.1 GPa develops into two (magnetic) transitions at T L and T H in the region of 0.1 L , T H and T d above 1.3 GPa. For decreasing temperature an abrupt increase of magnetization, M(T), has been observed below T H and a round maximum of magnetization appears at T L for P≥0.4 GPa. Above 1.3 GPa, an anomalous decrease of M(T) begins at T d =10 K. Using previously reported 31 P-NMR shift data it is shown that the pressure dependence of a characteristic temperature, which is proportional to the crystal field splitting in the paramagnetic temperature region, decreases rapidly with increasing pressure. (orig.)

Ductile fracture prediction of an axially cracked pressure vessel under pressurized thermal shock

International Nuclear Information System (INIS)

Takahashi, Jun; Okamura, Hiroyuki

1991-01-01

In this paper, the J-value of an axially cracked cylinder under several PTS conditions are evaluated using a simple estimation scheme which we proposed. Results obtained are summerized as follow: (1) Under any PTS conditions, the effect of internal pressure is so predominant upon the J-value and dJ/da that it is very important to grasp the transient of internal pressure under any imaginable accident from the viewpoint of structural integrity. (2) Under any IP, TS, and PTS conditions, J - a/W relation shows that the J-value reaches its maximum at a certain crack depth, then drops to zero at a/W ≅ 0.9. Though the effect of inertia is not taken into account, this fact may explain the phenomena of crack arrest qualitatively. (3) The compliance of a cylindrical shell plays an important role in the fracture prediction of a pressure vessel. (4) Under typical PTS conditions, the region at the crack tip dominated by the Hutchinson-Rice-Rosengren singularity is substantially large enough to apply the J-based criterion to predict unstable ductile fracture. (author)

Maximum concentrations at work and maximum biologically tolerable concentration for working materials 1991

International Nuclear Information System (INIS)

1991-01-01

The meaning of the term 'maximum concentration at work' in regard of various pollutants is discussed. Specifically, a number of dusts and smokes are dealt with. The valuation criteria for maximum biologically tolerable concentrations for working materials are indicated. The working materials in question are corcinogeneous substances or substances liable to cause allergies or mutate the genome. (VT) [de

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Science.gov (United States)

2010-07-01

... cylinders having an internal diameter of 13.0 cm and a 15.5 cm stroke length, the rounded displacement would... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Maximum engine power, displacement... Maximum engine power, displacement, power density, and maximum in-use engine speed. This section describes...

Search for the maximum efficiency of a ribbed-surfaces device, providing a tight seal

International Nuclear Information System (INIS)

Boutin, Jeanne.

1977-04-01

The purpose of this experiment was to determine the geometrical characteristics of ribbed surfaces used to equip devices in translation or slow rotation motion and having to form an acceptable seal between slightly viscous fluids. It systematically studies the pressure loss coefficient lambda in function of the different parameters setting the form of ribs and their relative position on the opposite sides. It shows that the passages with two ribbed surfaces lead to highly better results than those with only one, the maximum value of lambda, equal to 0.5, being obtained with the ratios: pitch/clearance = 5, depth of groove/clearance = 1,2, and with their teeth face to face on the two opposite ribbed surfaces. With certain shapes, alternate position of ribs can lead to the maximum of lambda yet lower than 0.5 [fr

Credal Networks under Maximum Entropy

OpenAIRE

Lukasiewicz, Thomas

2013-01-01

We apply the principle of maximum entropy to select a unique joint probability distribution from the set of all joint probability distributions specified by a credal network. In detail, we start by showing that the unique joint distribution of a Bayesian tree coincides with the maximum entropy model of its conditional distributions. This result, however, does not hold anymore for general Bayesian networks. We thus present a new kind of maximum entropy models, which are computed sequentially. ...

Numerical simulation of abutment pressure redistribution during face advance

Science.gov (United States)

Klishin, S. V.; Lavrikov, S. V.; Revuzhenko, A. F.

2017-12-01

The paper presents numerical simulation data on the abutment pressure redistribution in rock mass during face advance, including isolines of maximum shear stress and pressure epures. The stress state of rock in the vicinity of a breakage heading is calculated by the finite element method using a 2D nonlinear model of a structurally heterogeneous medium with regard to plasticity and internal self-balancing stress. The thus calculated stress field is used as input data for 3D discrete element modeling of the process. The study shows that the abutment pressure increases as the roof span extends and that the distance between the face breast and the peak point of this pressure depends on the elastoplastic properties and internal self-balancing stress of a rock medium.

A high-pressure thermal gradient block for investigating microbial activity in multiple deep-sea samples

DEFF Research Database (Denmark)

Kallmeyer, J.; Ferdelman, TG; Jansen, KH

2003-01-01

Details about the construction and use of a high-pressure thermal gradient block for the simultaneous incubation of multiple samples are presented. Most parts used are moderately priced off-the-shelf components that easily obtainable. In order to keep the pressure independent of thermal expansion....... Sulfate reduction rates increase with increasing pressure and show maximum values at pressures higher than in situ. (C) 2003 Elsevier Science B.V. All rights reserved....

30 CFR 75.504 - Permissibility of new, replacement, used, reconditioned, additional, and rebuilt electric face...

Science.gov (United States)

2010-07-01

... STANDARDS-UNDERGROUND COAL MINES Electrical Equipment-General § 75.504 Permissibility of new, replacement... new, replacement, used, reconditioned, and additional electric face equipment used in any mine..., unless in the opinion of the Secretary, such equipment or necessary replacement parts are not available...

Maximum Entropy in Drug Discovery

Directory of Open Access Journals (Sweden)

Chih-Yuan Tseng

2014-07-01

Full Text Available Drug discovery applies multidisciplinary approaches either experimentally, computationally or both ways to identify lead compounds to treat various diseases. While conventional approaches have yielded many US Food and Drug Administration (FDA-approved drugs, researchers continue investigating and designing better approaches to increase the success rate in the discovery process. In this article, we provide an overview of the current strategies and point out where and how the method of maximum entropy has been introduced in this area. The maximum entropy principle has its root in thermodynamics, yet since Jaynes’ pioneering work in the 1950s, the maximum entropy principle has not only been used as a physics law, but also as a reasoning tool that allows us to process information in hand with the least bias. Its applicability in various disciplines has been abundantly demonstrated. We give several examples of applications of maximum entropy in different stages of drug discovery. Finally, we discuss a promising new direction in drug discovery that is likely to hinge on the ways of utilizing maximum entropy.

36 CFR 223.7 - Permission for free use of timber outside free-use areas.

Science.gov (United States)

2010-07-01

..., DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER General Provisions § 223.7 Permission for free use of timber outside free-use areas. Similar material may be cut outside of a free-use area without permit in cases of emergency, but the person taking such material shall promptly notify...

How to design your stand-by diesel generator unit for maximum reliability

International Nuclear Information System (INIS)

Kauffmann, W.M.

1979-01-01

Critical stand-by power applications, such as in a nuclear plant, or radio support stations, demand exacting guidelines for positive start, rapid acceleration, load acceptance with minimum voltage drop, and quick recovery to rated voltage. The design of medium-speed turbocharged and intercooled diesel-engine-generator for this purpose is considered. Selection of the diesel engine, size, and number of units, from the standpoint of cost, favors minimum number of units with maximum horsepower capability. Four-cycle diesels are available in 16 to 20 cyinders V-configurations, with 200 BMEP (brake mean-effective pressure) continuous and 250 BMEP peaking

Maximum Quantum Entropy Method

OpenAIRE

Sim, Jae-Hoon; Han, Myung Joon

2018-01-01

Maximum entropy method for analytic continuation is extended by introducing quantum relative entropy. This new method is formulated in terms of matrix-valued functions and therefore invariant under arbitrary unitary transformation of input matrix. As a result, the continuation of off-diagonal elements becomes straightforward. Without introducing any further ambiguity, the Bayesian probabilistic interpretation is maintained just as in the conventional maximum entropy method. The applications o...

Analytical studies on optimization of containment design pressure

International Nuclear Information System (INIS)

Haware, S.K.; Ghosh, A.K.; Kushwaha, H.S.

2005-01-01

The containment of the proposed Advanced Heavy Water Reactor (AHWR) is divided into two main volumes viz. V1 and V2 interconnected by vent system via suppression pool. The arrangement is such that the volume V2 surrounds the volume V1 (see Fig.1). Blow Out Panels (BOPs), installed on volume V1 are designed to rupture at a differential pressure of 50 kPa. The containment was analysed using the in-house developed code CONTRAN, for three different scenario considered viz. (i) Loss of Coolant Accident (LOCA) involving double ended break in the downcomer pipe, (ii) LOCA involving double ended break in the reactor inlet header and (iii) Main Steam Line Break (MSLB) Accident. It was revealed that the accident involving the double-ended break of reactor inlet header results in the maximum value of the containment peak pressure. Results of the analyses indicated that the size of the BOP has bearing on the containment peak pressure. Therefore, five cases were analysed, varying the size of BOP from 0 to 10 m 2 , in order to quantify the influence of the size of BOP on the containment peak pressure. The blowdown mass and energy discharge data calculated using the code RELAP5/MOD3.2 was used in the analysis. It was observed that the vents are cleared in around 0.41 seconds into the accident. The containment peak pressures obtained in various cases are presented in Fig.2. The containment peak pressure varies with the size of BOP and passes through minima for a BOP size of around 5 m 2 . There are two flow processes, competing with each other viz. the steam-air mixture passage through the vent system via suppression pool and direct passage of steam air mixture through BOP bypassing the suppression pool. Though the energy suppression efficiency of the suppression pool decreases with increasing size of BOP, the pressure suppression efficiency was found to be maximum at around 5 m 2 size of BOP. The containment peak pressure passing through minima indicates that there is a scope for

Design of a new urban wind turbine airfoil using a pressure-load inverse method

Energy Technology Data Exchange (ETDEWEB)

Henriques, J.C.C.; Gato, L.M.C. [IDMEC, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Marques da Silva, F. [LNEC - Laboratorio Nacional de Engenharia Civil, Av. Brasil, 101, 1700-066 Lisboa (Portugal); Estanqueiro, A.I. [INETI - Instituto Nacional de Engenharia, Tecnologia e Inovacao Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal)

2009-12-15

This paper presents the design methodology of a new wind turbine airfoil that achieves high performance in urban environment by increasing the maximum lift. For this purpose, an inverse method was applied to obtain a new wind turbine blade section with constant pressure-load along the chord, at the design inlet angle. In comparison with conventional blade section designs, the new airfoil has increased maximum lift, reduced leading edge suction peak and controlled soft-stall behaviour, due to a reduction of the adverse pressure gradient on the suction side. Wind tunnel experimental results confirmed the computational results. (author)

Determination of Permissible Short-Time Emergency Overloading of Turbo-Generators and Synchronous Compensators

Directory of Open Access Journals (Sweden)

V. A. Anischenko

2011-01-01

Full Text Available The paper shows that failure to take into account variable ratio of short-time emergency overloading of turbo-generators (synchronous compensators that can lead to underestimation of overloading capacity or impermissible insulation over-heating.A method has been developed for determination of permissible duration of short-time emergency over-loading that takes into account changes of over-loading ratio in case of a failure.

The pressure effect on the superconducting transition temperature of black phosphorus

CERN Document Server

Karuzawa, M; Endo, S

2002-01-01

We have measured the pressure effect on the superconducting transition temperature T sub c of black phosphorus up to 160 GPa using a superconducting quantum interference device vibrating coil magnetometer. It was found that T sub c had a maximum value of about 9.5 K at about 32 GPa, began decreasing with pressure and reached about 4.3 K at about 100 GPa.

Control-rod, pressure and flow-induced accident and transient analysis of a direct-cycle, supercritical-pressure, light-water-cooled fast breeder reactor

International Nuclear Information System (INIS)

Kitoh, Kazuaki; Koshizuka, Seiichi; Oka, Yoshiaki

1996-01-01

The features of the direct-cycle, supercritical-pressure, light-water-cooled fast breeder reactor (SCFBR) are high thermal efficiency and simple reactor system. The safety principle is basically the same as that of an LWR since it is a water-cooled reactor. Maintaining the core flow is the basic safety requirement of the reactor, since its coolant system is the one through type. The transient behaviors at control rod, pressure and flow-induced abnormalities are analyzed and presented in this paper. The results of flow-induced transients of SCFBR were reported at ICONE-3, though pressure change was neglected. The change of fuel temperature distribution is also considered for the analysis of the rapid reactivity-induced transients such as control rod withdrawal. Total loss of flow and pump seizure are analyzed as the accidents. Loss of load, control rod withdrawal from the normal operation, loss of feedwater heating, inadvertent start of an auxiliary feedwater pump, partial loss of coolant flow and loss of external power are analyzed as the transients. The behavior of the flow-induced transients is not so much different from the analyses assuming constant pressure. Fly wheels should be equipped with the feedwater pumps to prolong the coast-down time more than 10s and to cope with the total loss of flow accident. The coolant density coefficient of the SCFBR is less than one tenth of a BWR in which the recirculation flow is used for the power control. The over pressurization transients at the loss of load is not so severe as that of a BWR. The power reaches 120%. The minimum deterioration heat flux ratio (MDHFR) and the maximum pressure are sufficiently lower than the criteria; MDHFR above 1.0 and pressure ratio below 1.10 of 27.5 MPa, maximum pressure for operation. Among the reactivity abnormalities, the control rod withdrawal transient from the normal operation is analyzed

ORION - Crew Module Side Hatch: Proof Pressure Test Anomaly Investigation

Science.gov (United States)

Evernden, Brent A.; Guzman, Oscar J.

2018-01-01

The Orion Multi-Purpose Crew Vehicle program was performing a proof pressure test on an engineering development unit (EDU) of the Orion Crew Module Side Hatch (CMSH) assembly. The purpose of the proof test was to demonstrate structural capability, with margin, at 1.5 times the maximum design pressure, before integrating the CMSH to the Orion Crew Module structural test article for subsequent pressure testing. The pressure test was performed at lower pressures of 3 psig, 10 psig and 15.75 psig with no apparent abnormal behavior or leaking. During pressurization to proof pressure of 23.32 psig, a loud 'pop' was heard at 21.3 psig. Upon review into the test cell, it was noted that the hatch had prematurely separated from the proof test fixture, thus immediately ending the test. The proof pressure test was expected be a simple verification but has since evolved into a significant joint failure investigation from both Lockheed Martin and NASA.

Superconductivity in CeRh2Si2 Under Pressure

International Nuclear Information System (INIS)

Araki, S.; Nakashima, M.; Settai, R.; Kobayashi, T.C.; Onuki, Y.

2003-01-01

We have studied the pressure-induced superconductivity in an antiferromagnet CeRh 2 Si 2 by measuring the electrical resistivity for a high-quality single crystal. The superconducting resistivity drop was observed around P c ∼eq 1.06 GPa, at which the Neel temperature becomes zero, namely in a pressure region from 0.97 to 1.20 GPa. The zero resistivity appears below 0.4 K between 1.03 to 1.08 GPa. The resistivity at low temperatures follows the Fermi liquid AT 2 relation in the whole pressure region, even at P c . The A value becomes a maximum around P c . (author)

Toward Improved Rotor-Only Axial Fans—Part II: Design Optimization for Maximum Efficiency

DEFF Research Database (Denmark)

Sørensen, Dan Nørtoft; Thompson, M. C.; Sørensen, Jens Nørkær

2000-01-01

Numerical design optimization of the aerodynamic performance of axial fans is carried out, maximizing the efficiency in a designinterval of flow rates. Tip radius, number of blades, and angular velocity of the rotor are fixed, whereas the hub radius andspanwise distributions of chord length......, stagger angle, and camber angle are varied to find the optimum rotor geometry.Constraints ensure a pressure rise above a specified target and an angle of attack on the blades below stall. The optimizationscheme is used to investigate the dependence of maximum efficiency on the width of the design interval...

Weighted Maximum-Clique Transversal Sets of Graphs

OpenAIRE

Chuan-Min Lee

2011-01-01

A maximum-clique transversal set of a graph G is a subset of vertices intersecting all maximum cliques of G. The maximum-clique transversal set problem is to find a maximum-clique transversal set of G of minimum cardinality. Motivated by the placement of transmitters for cellular telephones, Chang, Kloks, and Lee introduced the concept of maximum-clique transversal sets on graphs in 2001. In this paper, we study the weighted version of the maximum-clique transversal set problem for split grap...

Improved plenum pressure gradient facemaps for PKL reactors

International Nuclear Information System (INIS)

Crowley, D.A.; Hamm, L.L.

1988-05-01

This report documents the development of improved plenum pressure gradient facemaps* for PKL Mark 16--31 and Mark 22 reactor charges. These new maps are based on the 1985 L-area AC flow tests. Use of the L-area data base for estimating C-area plenum pressure gradient maps is inappropriate because the nozzle geometry plays a major role in determining the shape of the plenum pressure profile. These plenum pressure gradient facemaps are used in the emergency cooling system (ECS) and in the flow instability (FI) loss of coolant accident (LOCA) limits calculations. For the ECS LOCA limits calculations, the maps are used as input to the FLOWZONE computer code to determine the average flow within a flowzone during normal operating conditions. For the FI LOCA limits calculations, the maps are used as plenum pressure boundary conditions in the FLOWTRAN computer code to determine the maximum pre-incident assembly flow within a flowzone. These maps will also be used for flowzoning and transient protection limits analyses

Severe bronchopulmonary dysplasia improved by noninvasive positive pressure ventilation: a case report

Directory of Open Access Journals (Sweden)

Mann Christian

2011-09-01

Full Text Available Abstract Introduction This is the first report to describe the feasibility and effectiveness of noninvasive positive pressure ventilation in the secondary treatment of bronchopulmonary dysplasia. Case presentation A former male preterm of Caucasian ethnicity delivered at 29 weeks gestation developed severe bronchopulmonary dysplasia. At the age of six months he was in permanent tachypnea and dyspnea and in need of 100% oxygen with a flow of 2.0 L/minute via a nasal cannula. Intermittent nocturnal noninvasive positive pressure ventilation was then administered for seven hours daily. The ventilator was set at a positive end-expiratory pressure of 6 cmH2O, with pressure support of 4 cmH2O, trigger at 1.4 mL/second, and a maximum inspiratory time of 0.7 seconds. Over the course of seven weeks, the patient's maximum daytime fraction of inspired oxygen via nasal cannula decreased from 1.0 to 0.75, his respiratory rate from 64 breaths/minute to 50 breaths/minute and carbon dioxide from 58 mmHg to 44 mmHg. Conclusion Noninvasive positive pressure ventilation may be a novel therapeutic option for established severe bronchopulmonary dysplasia. In the case presented, noninvasive positive pressure ventilation achieved sustained improvement in ventilation and thus prepared our patient for safe home oxygen therapy.

Method for verifying the pressure in a nuclear reactor fuel rod

International Nuclear Information System (INIS)

Jones, W.J.

1979-01-01

Disclosed is a method of accurately verifying the pressure contained in a sealed pressurized fuel rod by utilizing a pressure balance measurement technique wherein an end of the fuel rod extends through and is sealed in a wall of a small chamber. The chamber is pressurized to the nominal (desired) fuel rod pressure and the fuel rod is then pierced to interconnect the chamber and fuel rod. The deviation of chamber pressure is noted. The final combined pressure of the fuel rod and drill chamber is substantially equal to the nominal rod pressure; departure of the combined pressure from nominal is in direct proportion to departure of rod pressure from nominal. The maximum error in computing the rod pressure from the deviation of the combined pressure from nominal is estimated at plus or minus 3.0 psig for rod pressures within the specified production limits. If the rod pressure is corrected for rod void volume using a digital printer data record, the accuracy improves to about plus or minus 2.0 psig

Oscillometric casual blood pressure normative standards for Swedish children using ABPM to exclude casual hypertension.

Science.gov (United States)

Krmar, Rafael T; Holtbäck, Ulla; Bergh, Anita; Svensson, Eva; Wühl, Elke

2015-04-01

Casual blood pressure (CBP) is considered a reliable proxy for cardiovascular health. Although the auscultatory technique is the reference standard method for measuring CBP, oscillometric devices are increasingly being used in children. We sought to establish oscillometric CBP normative standards for Swedish children. Cross-sectional oscillometric CBP readings were obtained by the Welch Allyn Spot Vital Signs 420 monitor and measured according to the International Guidelines' recommendations. Participants with elevated oscillometric CBP levels underwent verification by the auscultatory method. Ambulatory blood pressure monitoring (ABPM) was used to exclude casual hypertension. Data on 1,470 (772 males) apparently healthy Swedish schoolchildren aged 6-16 years were analyzed and sex-specific reference charts normalized to age or height were constructed. Systolic and diastolic CBP values were significantly higher with age, height, height standard deviation score (SDS), body mass index (BMI), and BMI SDS. Gender differences for systolic CBP were present starting from age of 15 years and revealed significantly higher values in boys than in girls, whereas for diastolic CBP, the differences were apparent at the age of 12 years, with higher values in girls. Increased BMI and BMI SDS were positively associated with CBP levels. Positive parental history of hypertension turned out to be a risk factor for higher systolic and diastolic CBP across all ages. Our normative standard for CBP can be used for blood pressure screening and control programs in Swedish children. The use of ABPM should be considered to confirm the diagnosis of casual hypertension. © American Journal of Hypertension, Ltd 2014. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Access to a Loaded Gun Without Adult Permission and School-Based Bullying.

Science.gov (United States)

Simckes, Maayan S; Simonetti, Joseph A; Moreno, Megan A; Rivara, Frederick P; Oudekerk, Barbara A; Rowhani-Rahbar, Ali

2017-09-01

Gun access and bullying are risk factors for sustaining or perpetrating violence among adolescents. Our knowledge of gun access among bullied students is limited. We used data on students, aged 12-18 years, from the 2011 and 2013 School Crime Supplement to the National Crime Victimization Survey to assess the association between self-reported bullying victimization (traditional and cyber) and access to a loaded gun without adult permission. Prevalence ratios (PRs) and confidence intervals (CIs) were obtained from multivariable Poisson regression using the Taylor series after controlling for student age, sex, family income, public/private school, and race. Of 10,704 participants, 4.2% (95% CI: 3.8%-4.6%) reported gun access. Compared with nonbullied students, those who reported traditional bullying (PR = 2.2; 95% CI: 1.7-2.4), cyberbullying (PR = 2.8; 95% CI: 1.6-4.9), and both (PR = 5.9; 95% CI: 4.6-7.7) were more likely to also report gun access. Adolescents who experience bullying, particularly those who report both traditional bullying and cyberbullying, are more likely to report access to a loaded gun without adult permission. These findings highlight the importance of developing interventions focused on these modifiable risk factors for preventing self-directed or interpersonal violence among youth. Copyright © 2017 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Maximum power demand cost

International Nuclear Information System (INIS)

Biondi, L.

1998-01-01

The charging for a service is a supplier's remuneration for the expenses incurred in providing it. There are currently two charges for electricity: consumption and maximum demand. While no problem arises about the former, the issue is more complicated for the latter and the analysis in this article tends to show that the annual charge for maximum demand arbitrarily discriminates among consumer groups, to the disadvantage of some [it

Generation of subnanosecond electron beams in air at atmospheric pressure

Science.gov (United States)

Kostyrya, I. D.; Tarasenko, V. F.; Baksht, E. Kh.; Burachenko, A. G.; Lomaev, M. I.; Rybka, D. V.

2009-11-01

Optimum conditions for the generation of runaway electron beams with maximum current amplitudes and densities in nanosecond pulsed discharges in air at atmospheric pressure are determined. A supershort avalanche electron beam (SAEB) with a current amplitude of ˜30 A, a current density of ˜20 A/cm2, and a pulse full width at half maximum (FWHM) of ˜100 ps has been observed behind the output foil of an air-filled diode. It is shown that the position of the SAEB current maximum relative to the voltage pulse front exhibits a time shift that varies when the small-size collector is moved over the foil surface.

On the transient pressure build-up in the full pressure safety shell of watercooled nuclear reactors after a loss of coolant accident

International Nuclear Information System (INIS)

Mansfeld, G.

1979-08-01

The thermo-and fluid-dynamic processes in a multichamber full pressure safety containment during a loss of coolant accident have been investigated. Comparison of the calculations carried out with the computer programs, in which ZOCO VI was used as being representative of similar programs, with the experimental results pointed out discrepancies in the determination of time dependent pressure, pressure difference and temperature curves. This led to the development of a new theoretical model and a program COFLOW which pays particular attention to the fluid dynamic processes in the initial phase of a loss of coolant accident. It can also be used to determine the maximum containment pressure towards the end of a loss of coolant accident. Comparison of the COFLOW results with experiments has shown that COFLOW provides a model and a procedure by which the physical processes in a multichamber full pressure safety containment can be simulated satisfactorily

NASA Space Radiation Protection Strategies: Risk Assessment and Permissible Exposure Limits

Science.gov (United States)

Huff, J. L.; Patel, Z. S.; Simonsen, L. C.

2017-01-01

Permissible exposure limits (PELs) for short-term and career astronaut exposures to space radiation have been set and approved by NASA with the goal of protecting astronauts against health risks associated with ionizing radiation exposure. Short term PELs are intended to prevent clinically significant deterministic health effects, including performance decrements, which could threaten astronaut health and jeopardize mission success. Career PELs are implemented to control late occurring health effects, including a 3% risk of exposure induced death (REID) from cancer, and dose limits are used to prevent cardiovascular and central nervous system diseases. For radiation protection, meeting the cancer PEL is currently the design driver for galactic cosmic ray and solar particle event shielding, mission duration, and crew certification (e.g., 1-year ISS missions). The risk of cancer development is the largest known long-term health consequence following radiation exposure, and current estimates for long-term health risks due to cardiovascular diseases are approximately 30% to 40% of the cancer risk for exposures above an estimated threshold (Deep Space one-year and Mars missions). Large uncertainties currently exist in estimating the health risks of space radiation exposure. Improved understanding through radiobiology and physics research allows increased accuracy in risk estimation and is essential for ensuring astronaut health as well as for controlling mission costs, optimization of mission operations, vehicle design, and countermeasure assessment. We will review the Space Radiation Program Element's research strategies to increase accuracy in risk models and to inform development and validation of the permissible exposure limits.

Analytic Method for Pressure Recovery in Truncated Diffusers ...

African Journals Online (AJOL)

A prediction method is presented for the static pressure recovery in subsonic axisymmetric truncated conical diffusers. In the analysis, a turbulent boundary layer is assumed at the diffuser inlet and a potential core exists throughout the flow. When flow separation occurs, this approach cannot be used to predict the maximum ...

Anomalous pressure dependence of the superconducting transition temperature in the β-Pyrochlore KOs2O6

Science.gov (United States)

Miyoshi, Kiyotaka; Takaichi, Yuta; Takeuchi, Jun

2009-03-01

DC magnetic measurements have been performed for β-pyrochlore superconductor KOs2O6 (Tc = 9.6 K) under pressure for the precise determination of the pressure dependence of Tc, using a miniature diamond anvil cell combined with a commercial SQUID magnetometer. It is found that the critical temperature Tc shows a maximum of ~10 K at P=0.5 GPa. The maximum of Tc is higher than that for CsOs2O6 and RbOs2O6, in both of which Tc is known to increase and saturate at Tcm = 8.8 K by the application of pressure, suggesting the enhanced superconductivity due to the rattling of K ions in an oversized cage of Os-O network. For the further application of pressure, Tc decreases linearly but the decreasing rate appears to be suddenly changed at P~2 GPa and Tc~8 K. The sharp bend of the Tc — P line probably corresponds to the transition concerning to the rattling motion which occurs at Tp=7.5 K at ambient pressure, suggesting the positive pressure dependence of Tp.

High pressure studies of as grown WX2-x single crystals

International Nuclear Information System (INIS)

Solanki, G.K.; Agarwal, M.K.; Patel, Yogesh A.

2011-01-01

The structural optical and transport properties of tungsten metal dichalogenides having layered structure have been extensively studied in the last two decades. These materials shows highly anisotropic behaviour and have been receiving considerable interest for a variety of applications. Several of these layered semiconductors have attracted attention as a new class of solar cell material. We present here the results of simultaneous resistivity and thermoelectric power (TEP) measurements upto 7 GPa on single crystals of WS 2 , WS 1.9 , WSe 2 and WSe 1.9 grown using Direct Vapour Transport (DVT) technique. The observations clearly shows WS 2 and WS 1.9 are more resistive compared to other two crystals. In all samples an exponential fall of resistivity on increases in pressure upto 2.1 GPa but after 2.2 GPa the resistivity decreases substantially with increases pressure. The TEP of WSe 2 increases steadily and reaches maximum at 0.65 GPa, while for WSe 1.9 TEP increases upto pressure 0.5 GPa. In both the cases after attaining the maximum TEP, then decreases monotonically with increase in pressure. TEP of WS 2 and WS 1.9 increase upto pressure 1.1 GPa, beyond 1.1 GPa pressure in both the cases TEP decreases steadily with further increase in pressure. In all the samples, the sign of TEP is positive indicating that all of them are p-type and remain p-type with increase in pressure. The variation of thermoelectric power factor with pressure has been thoroughly studied. An analysis of the data point out that perfectly stoichiometric crystals of WSe 2 work as superior thermoelectric materials. The results have been presented and implications have been discussed. (author)

Experimental study of the pressure characteristics in the Stirling refrigerator

International Nuclear Information System (INIS)

Hong, Yong Ju; Park, Seong Je; Kim, Hyo Bong; Koh, Deuk Yong

2001-01-01

The linear compressor have been widely used for pressure wave generation in the Stirling cryocooler and Stirling type pulse tube cryocooler for tactical purpose. The linear compressor has small and compact structure, and long life due to having non-contact sealing mechanism and the pressure drop through regenerator was ver important role in the motion of displacer in the expander of the Stirling cryocooler. In this study, the characteristic of the linear compressor and the pressure drop through regenerator in the expander was experimentally investigated. The results show resonance of the compressor is very important to get maximum performance and the gas spring force in the compression space of the compressor has effect on the characteristic of resonance and the results show the pressure drop through regenerator is very small than operating pressure change

Weakest solar wind of the space age and the current 'MINI' solar maximum

International Nuclear Information System (INIS)

McComas, D. J.; Angold, N.; Elliott, H. A.; Livadiotis, G.; Schwadron, N. A.; Smith, C. W.; Skoug, R. M.

2013-01-01

The last solar minimum, which extended into 2009, was especially deep and prolonged. Since then, sunspot activity has gone through a very small peak while the heliospheric current sheet achieved large tilt angles similar to prior solar maxima. The solar wind fluid properties and interplanetary magnetic field (IMF) have declined through the prolonged solar minimum and continued to be low through the current mini solar maximum. Compared to values typically observed from the mid-1970s through the mid-1990s, the following proton parameters are lower on average from 2009 through day 79 of 2013: solar wind speed and beta (∼11%), temperature (∼40%), thermal pressure (∼55%), mass flux (∼34%), momentum flux or dynamic pressure (∼41%), energy flux (∼48%), IMF magnitude (∼31%), and radial component of the IMF (∼38%). These results have important implications for the solar wind's interaction with planetary magnetospheres and the heliosphere's interaction with the local interstellar medium, with the proton dynamic pressure remaining near the lowest values observed in the space age: ∼1.4 nPa, compared to ∼2.4 nPa typically observed from the mid-1970s through the mid-1990s. The combination of lower magnetic flux emergence from the Sun (carried out in the solar wind as the IMF) and associated low power in the solar wind points to the causal relationship between them. Our results indicate that the low solar wind output is driven by an internal trend in the Sun that is longer than the ∼11 yr solar cycle, and they suggest that this current weak solar maximum is driven by the same trend.

Study of radial die-wall pressure changes during pharmaceutical powder compaction.

Science.gov (United States)

Abdel-Hamid, Sameh; Betz, Gabriele

2011-04-01

In tablet manufacturing, less attention is paid to the measurement of die-wall pressure than to force-displacement diagrams. Therefore, the aim of this study was to investigate radial stress change during pharmaceutical compaction. The Presster(TM), a tablet-press replicator, was used to characterize compaction behavior of microcrystalline cellulose (viscoelastic), calcium hydrogen phosphate dihydrate (brittle), direct compressible mannitol (plastic), pre-gelatinized starch (plastic/elastic), and spray dried lactose monohydrate (plastic/brittle) by measuring radial die-wall pressure; therefore powders were compacted at different (pre) compaction pressures as well as different speeds. Residual die-wall pressure (RDP) and maximum die-wall pressure (MDP) were measured. Various tablet physical properties were correlated to radial die-wall pressure. With increasing compaction pressure, RDP and MDP (P compaction behavior of materials and detecting friction phenomena in the early stage of development.

La Substitution and Pressure Studies on CeCoSi: A Possible Antiferroquadrupolar Ordering Induced by Pressure

Science.gov (United States)

Tanida, Hiroshi; Muro, Yuji; Matsumura, Takeshi

2018-02-01

The La-substitution and pressure effects on antiferromagnet CeCoSi with a tetragonal crystal structure were investigated in order to clarify the origin of the pressure induced ordered phase (PIOP) with an enormously high transition temperature of T0 ˜ 38 K. By substituting Ce with La, the PIOP shifts to high pressures, and the maximum value of T0 is suppressed, indicating that the PIOP originates from a Ce-Ce interaction. At T0, the magnetic susceptibility exhibits not a cusp, but an increase with decreasing temperature, as is frequently observed in antiferroquadrupolar (AFQ) ordering. Based on these results, we propose that a possible origin of the PIOP is an AFQ ordered phase of Ce-4f electron. Due to the lack of local inversion symmetry at the Ce sites, the AFQ order could be accompanied by odd parity multipolar moments. Since there is no clear evidence of successive transitions below T0, the remaining Kramers degeneracy could be lifted by the Kondo coupling.

Reduced oxygen at high altitude limits maximum size.

Science.gov (United States)

Peck, L S; Chapelle, G

2003-11-07

The trend towards large size in marine animals with latitude, and the existence of giant marine species in polar regions have long been recognized, but remained enigmatic until a recent study showed it to be an effect of increased oxygen availability in sea water of a low temperature. The effect was apparent in data from 12 sites worldwide because of variations in water oxygen content controlled by differences in temperature and salinity. Another major physical factor affecting oxygen content in aquatic environments is reduced pressure at high altitude. Suitable data from high-altitude sites are very scarce. However, an exceptionally rich crustacean collection, which remains largely undescribed, was obtained by the British 1937 expedition from Lake Titicaca on the border between Peru and Bolivia in the Andes at an altitude of 3809 m. We show that in Lake Titicaca the maximum length of amphipods is 2-4 times smaller than other low-salinity sites (Caspian Sea and Lake Baikal).

78 FR 52915 - Notice of Proposals to Engage In or To Acquire Companies Engaged in Permissible Nonbanking...

Science.gov (United States)

2013-08-27

... to be closely related to banking and permissible for bank holding companies. Unless otherwise noted..., Vice President) 2200 North Pearl Street, Dallas, Texas 75201-2272: 1. Rio Financial Services, Inc...

Predicting failure to follow-up screened high blood pressure in Japan: a cohort study.

Science.gov (United States)

Kuriyama, Akira; Takahashi, Yoshimitsu; Tsujimura, Yuka; Miyazaki, Kikuko; Satoh, Toshihiko; Ikeda, Shunya; Nakayama, Takeo

2015-09-01

This study aimed to determine the prevalence and predictors of working-age individuals who did not follow-up for possible hypertension that was detected in the population-based screening. We conducted a retrospective cohort study, using the database of health insurance claims and health checkups from several health insurance societies for employees in Japan. Screened participants aged ≥20 years, with possible hypertension (systolic blood pressure ≥140 mmHg and/or diastolic blood pressure ≥90 mmHg) and without known antihypertensive treatment, were included. The outcome was lack of clinical follow-up for possible hypertension within 6 months of the latest screening. Multivariate logistic regression analysis was performed to identify predictors. Among 17,173 participants (15,793 males and 1380 females) who were identified as possible hypertensives, 89.7 and 82.3% of them, respectively, did not consult physicians for screened possible hypertension. Predictors of no clinical follow-up for males included younger age, lower body mass index (BMI), lower hemoglobin A1c and milder hypertension. Predictors for females included younger age, lower BMI and being insured. Approximately 80% of participants failed to consult physicians even with positive screening results. Younger individuals with lower BMI are at high risk of no clinical follow-up. © The Author 2014. Published by Oxford University Press on behalf of Faculty of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Radiation-induced polymerization of glass-forming systems. VII. Polymerization in supercooled state under high pressure

International Nuclear Information System (INIS)

Kaetsu, I.; Yoshii, F.; Watanabe, Y.

1978-01-01

Radiation-induced polymerization of glass-forming monomers such as 2-hydroxyethyl methacrylate and glycidyl methacrylate under high pressure was studied. The glass transition temperature of these monomers was heightened by increased pressure. The temperature dependence of polymerizability showed a characteristic relation, similar to those in supercooled-phase polymerization under normal pressure, that had a maximum at T/sub ν/ which shifted to higher levels of temperature as well as to T/sub g/ under high pressure. Polymerizability in the supercooled state also increased under increased pressure

Blood pressure and pain sensitivity in children and adolescents.

Science.gov (United States)

Drouin, Sammantha; McGrath, Jennifer J

2013-06-01

Elevated blood pressure is associated with diminished pain sensitivity. While this finding is well established in adults, it is less clear when the relation between blood pressure and pain sensitivity emerges across the life course. Evidence suggests this phenomenon may exist during childhood. Children (N = 309; 56% boys) aged 10-15 years and their parents participated. Blood pressure readings were taken during a resting baseline. Maximum pain intensity was rated using a visual analogue scale (rated 0-10) in response to a finger prick pain induction. Parent-measured resting blood pressure was inversely associated with boys' pain ratings only. Cross-sectionally, lower pain ratings were related to higher SBP, univariately. Longitudinally, pain ratings predicted higher DBP, even after controlling for covariates. Determining when and how the relation between blood pressure and pain sensitivity emerges may elucidate the pathophysiology of hypertension. Copyright © 2013 Society for Psychophysiological Research.

The Association of Pediatric Obesity With Nocturnal Non-Dipping on 24-Hour Ambulatory Blood Pressure Monitoring.

Science.gov (United States)

Macumber, Ian R; Weiss, Noel S; Halbach, Susan M; Hanevold, Coral D; Flynn, Joseph T

2016-05-01

Obesity has been linked with abnormal nocturnal dipping of blood pressure (BP) in adults, which in turn is associated with poor cardiovascular outcomes. There are few data regarding abnormal dipping status in the obese pediatric population. The goal of this study was to further describe the relationship between obesity and non-dipping status on ambulatory blood pressure monitor (ABPM) in children. We conducted a cross-sectional study using a database of patients aged 5-21 years who had undergone 24-hour ABPM at Seattle Children's Hospital from January 2008 through May 2014. Subjects were grouped by body mass index (BMI) into lean (BMI 15th-85th percentile) and obese (BMI >95th percentile) groups. Compared to lean subjects (n = 161), obese subjects (n = 247) had a prevalence ratio (PR) for non-dipping of 2.15, adjusted for race (95% confidence interval (CI) = 1.25-3.42). Increasing severity of obesity was not further associated with nocturnal non-dipping. Nocturnal non-dipping was not associated with left ventricular hypertrophy (PR = 1.01, 95% CI = 0.71-1.44). These results suggest that in children, just as in adults, obesity is related to a relatively decreased dipping in nocturnal BP. © American Journal of Hypertension, Ltd 2015. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A new method to normalize plantar pressure measurements for foot size and foot progression angle.

NARCIS (Netherlands)

Keijsers, N.L.; Stolwijk, N.M.; Nienhuis, B.; Duysens, J.E.J.

2009-01-01

Plantar pressure measurement provides important information about the structure and function of the foot and is a helpful tool to evaluate patients with foot complaints. In general, average and maximum plantar pressure of 6-11 areas under the foot are used to compare groups of subjects. However,

Ultra high pressure liquid chromatography. Column permeability and changes of the eluent properties.

Science.gov (United States)

Gritti, Fabrice; Guiochon, Georges

2008-04-11

The behavior of four similar liquid chromatography columns (2.1mm i.d. x 30, 50, 100, and 150 mm, all packed with fine particles, average d(p) approximately 1.7 microm, of bridged ethylsiloxane/silica hybrid-C(18), named BEH-C(18)) was studied in wide ranges of temperature and pressure. The pressure and the temperature dependencies of the viscosity and the density of the eluent (pure acetonitrile) along the columns were also derived, using the column permeabilities and applying the Kozeny-Carman and the heat balance equations. The heat lost through the external surface area of the chromatographic column was directly derived from the wall temperature of the stainless steel tube measured with a precision of +/-0.2 degrees C in still air and +/-0.1 degrees C in the oven compartment. The variations of the density and viscosity of pure acetonitrile as a function of the temperature and pressure was derived from empirical correlations based on precise experimental data acquired between 298 and 373 K and at pressures up to 1.5 kbar. The measurements were made with the Acquity UPLC chromatograph that can deliver a maximum flow rate of 2 mL/min and apply a maximum column inlet pressure of 1038 bar. The average Kozeny-Carman permeability constant of the columns was 144+/-3.5%. The temperature hence the viscosity and the density profiles of the eluent along the column deviate significantly from linear behavior under high-pressure gradients. For a 1000 bar pressure drop, we measured DeltaT=25-30 K, (Deltaeta/eta) approximately 100%, and (Deltarho/rho) approximately 10%. These results show that the radial temperature profiles are never fully developed within 1% for any of the columns, even under still-air conditions. This represents a practical advantage regarding the apparent column efficiency at high flow rates, since the impact of the differential analyte velocity between the column center and the column wall is not maximum. The interpretation of the peak profiles recorded in

Phase stability of TiH{sub 2} under high pressure and temperatures

Energy Technology Data Exchange (ETDEWEB)

Selva Vennila, R.; Durygin, A.; Saxena, S.K. [Center for Study of Matter at Extreme Conditions (CeSMEC), Florida International University, VH-150, University Park, Miami, FL 33199 (United States); Merlini, Marco [European Synchrotron Radiation Facility (ESRF), Grenoble 38043 (France); Wang, Zhongwu [Cornell High Energy Synchrotron Source (CHESS), Wilson Laboratory, Cornell University, Ithaca, NY 14853 (United States)

2008-11-15

Phase stability of titanium hydride (TiH{sub 2}) was studied at high pressure-high temperature conditions using synchrotron radiation under non-hydrostatic conditions. Resistive heating method was used to heat the sample to a maximum temperature of 873 K in a diamond anvil cell (DAC) under pressure up to 12 GPa. Pressure-temperature behavior was studied by varying the temperature upto 823 K in steps of 50 K with pressure variations within 3 GPa. Structural phase transformation from tetragonal (I4/mmm) to cubic (Fm-3 m) was observed with increase in temperature. Tetragonal phase was found to be stabilized when the sample was subjected to pressure and temperature cycle. (author)

Maximum home systolic blood pressure is a useful indicator of arterial stiffness in patients with type 2 diabetes mellitus: post hoc analysis of a cross-sectional multicenter study.

Science.gov (United States)

Ushigome, Emi; Fukui, Michiaki; Hamaguchi, Masahide; Tanaka, Toru; Atsuta, Haruhiko; Mogami, Shin-ichi; Tsunoda, Sei; Yamazaki, Masahiro; Hasegawa, Goji; Nakamura, Naoto

2014-09-01

Maximum (max) home systolic blood pressure (HSBP) as well as mean HSBP or HSBP variability was reported to increase the predictive value of target organ damage. Yet, the association between max HSBP and target organ damage in patients with type 2 diabetes has never been reported. The aim of this study was to investigate the association between max HSBP and pulse wave velocity (PWV), a marker of arterial stiffness which in turn is a marker of target organ damage, in patients with type 2 diabetes. We assessed the relationship of mean HSBP or max HSBP to PWV, and compared area under the receiver-operating characteristic curve (AUC) of mean HSBP or max HSBP for arterial stiffness in 758 patients with type 2 diabetes. In the univariate analyses, age, duration of diabetes mellitus, body mass index, mean clinic systolic blood pressure (SBP), mean HSBP and max HSBP were associated with PWV. Multivariate linear regression analyses indicated that mean morning SBP (β=0.156, P=0.001) or max morning SBP (β=0.146, P=0.001) were significantly associated with PWV. AUC (95% CI) for arterial stiffness, defined as PWV equal to or more than 1800 cm per second, in mean morning SBP and max morning SBP were 0.622 (0.582-0.662; P<0.001) and 0.631 (0.591-0.670; P<0.001), respectively. Our findings implicate that max HSBP as well as mean HSBP was significantly associated with arterial stiffness in patients with type 2 diabetes. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

49 CFR 230.24 - Maximum allowable stress.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Maximum allowable stress. 230.24 Section 230.24... Allowable Stress § 230.24 Maximum allowable stress. (a) Maximum allowable stress value. The maximum allowable stress value on any component of a steam locomotive boiler shall not exceed 1/4 of the ultimate...

Air charged and microtip catheters cannot be used interchangeably for urethral pressure measurement: a prospective, single-blind, randomized trial.

Science.gov (United States)

Zehnder, Pascal; Roth, Beat; Burkhard, Fiona C; Kessler, Thomas M

2008-09-01

We determined and compared urethral pressure measurements using air charged and microtip catheters in a prospective, single-blind, randomized trial. A consecutive series of 64 women referred for urodynamic investigation underwent sequential urethral pressure measurements using an air charged and a microtip catheter in randomized order. Patients were blinded to the type and sequence of catheter used. Agreement between the 2 catheter systems was assessed using the Bland and Altman 95% limits of agreement method. Intraclass correlation coefficients of air charged and microtip catheters for maximum urethral closure pressure at rest were 0.97 and 0.93, and for functional profile length they were 0.9 and 0.78, respectively. Pearson's correlation coefficients and Lin's concordance coefficients of air charged and microtip catheters were r = 0.82 and rho = 0.79 for maximum urethral closure pressure at rest, and r = 0.73 and rho = 0.7 for functional profile length, respectively. When applying the Bland and Altman method, air charged catheters gave higher readings than microtip catheters for maximum urethral closure pressure at rest (mean difference 7.5 cm H(2)O) and functional profile length (mean difference 1.8 mm). There were wide 95% limits of agreement for differences in maximum urethral closure pressure at rest (-24.1 to 39 cm H(2)O) and functional profile length (-7.7 to 11.3 mm). For urethral pressure measurement the air charged catheter is at least as reliable as the microtip catheter and it generally gives higher readings. However, air charged and microtip catheters cannot be used interchangeably for clinical purposes because of insufficient agreement. Hence, clinicians should be aware that air charged and microtip catheters may yield completely different results, and these differences should be acknowledged during clinical decision making.

Increasing the maximum daily operation time of MNSR reactor by modifying its cooling system

International Nuclear Information System (INIS)

Khamis, I.; Hainoun, A.; Al Halbi, W.; Al Isa, S.

2006-08-01

thermal-hydraulic natural convection correlations have been formulated based on a thorough analysis and modeling of the MNSR reactor. The model considers detailed description of the thermal and hydraulic aspects of cooling in the core and vessel. In addition, determination of pressure drop was made through an elaborate balancing of the overall pressure drop in the core against the sum of all individual channel pressure drops employing an iterative scheme. Using this model, an accurate estimation of various timely core-averaged hydraulic parameters such as generated power, hydraulic diameters, flow cross area, ... etc. for each one of the ten-fuel circles in the core can be made. Furthermore, distribution of coolant and fuel temperatures, including maximum fuel temperature and its location in the core, can now be determined. Correlation among core-coolant average temperature, reactor power, and core-coolant inlet temperature, during both steady and transient cases, have been established and verified against experimental data. Simulating various operating condition of MNSR, good agreement is obtained for at different power levels. Various schemes of cooling have been investigated for the purpose of assessing potential benefits on the operational characteristics of the syrian MNSR reactor. A detailed thermal hydraulic model for the analysis of MNSR has been developed. The analysis shows that an auxiliary cooling system, for the reactor vessel or installed in the pool which surrounds the lower section of the reactor vessel, will significantly offset the consumption of excess reactivity due to the negative reactivity temperature coefficient. Hence, the maximum operating time of the reactor is extended. The model considers detailed description of the thermal and hydraulic aspects of cooling the core and its surrounding vessel. Natural convection correlations have been formulated based on a thorough analysis and modeling of the MNSR reactor. The suggested 'micro model

Effects of body position and sex group on tongue pressure generation.

Science.gov (United States)

Dietsch, Angela M; Cirstea, Carmen M; Auer, Ed T; Searl, Jeff P

2013-11-01

Fine control of orofacial musculature is necessary to precisely accelerate and decelerate the articulators across exact distances for functional speech and coordinated swallows (Amerman & Parnell, 1990; Benjamin, 1997; Kent, Duffy, Slama, Kent, & Clift, 2001). Enhanced understanding of neural control for such movements could clarify the nature of and potential remediation for some dysarthrias and other orofacial myofunctional impairments. Numerous studies have measured orolingual force and accuracy during speech and nonspeech tasks, but have focused on young adults, maximum linguapalatal pressures, and upright positioning (O'Day, Frank, Montgomery, Nichols, & McDade, 2005; Solomon & Munson, 2004; Somodi, Robin, & Luschei, 1995; Youmans, Youmans, & Stierwalt, 2009). Patients' medical conditions or testing procedures such as concurrent neuroimaging may preclude fully upright positioning during oral motor assessments in some cases. Since judgments about lingual strength and coordination can influence clinical decisions regarding the functionality of swallowing and speech, it is imperative to understand any effects of body positioning differences. In addition, sex differences in the control of such tasks are not well defined. Therefore, this study evaluated whether pressures exerted during tongue movements differ in upright vs. supine body position in healthy middle-aged men and women. Twenty healthy middle-aged adults compressed small air-filled plastic bulbs in the oral cavity at predetermined fractions of task-specific peak pressure in a randomized block design. Tasks including phoneme repetitions and nonspeech isometric contractions were executed in upright and supine positions. Participants received continuous visual feedback regarding targets and actual exerted pressures. Analyses compared average pressure values for each subject, task, position, and effort level. Speech-like and nonspeech tongue pressures did not differ significantly across body position or sex

Flow condensation pressure drop characteristics of R410A-oil mixture inside small diameter horizontal microfin tubes

Energy Technology Data Exchange (ETDEWEB)

Huang, Xiangchao; Ding, Guoliang; Hu, Haitao; Zhu, Yu [Institute of Refrigeration and Cryogenics, Shanghai Jiaotong University, Shanghai 200240 (China); Gao, Yifeng [International Copper Association Shanghai Office, Shanghai 200020 (China); Deng, Bin [Institute of Heat Transfer Technology, Golden Dragon Precise Copper Tube Group Inc., Shanghai 200135 (China)

2010-11-15

Flow condensation pressure drop characteristics of R410A-oil mixture inside small diameter (5.0 mm and 4.0 mm O.D.) horizontal microfin tubes were investigated experimentally covering nominal oil concentrations from 0% to 5%. The research results indicate that, comparing with the frictional pressure drop of pure R410A, the frictional pressure drop of R410A-oil mixture may decrease by maximum of 18% when the vapor quality is lower than 0.6, and increase by maximum of 13% when the vapor quality is higher than 0.6. A new frictional pressure drop correlation for R410A-oil mixture flow condensation inside microfin tubes is developed based on the refrigerant-oil mixture properties, and can agree with 94% of the experimental data within a deviation of -30% to +30%. (author)

Human T Lymphocytes Are Permissive for Dengue Virus Replication.

Science.gov (United States)

Silveira, Guilherme F; Wowk, Pryscilla F; Cataneo, Allan H D; Dos Santos, Paula F; Delgobo, Murilo; Stimamiglio, Marco A; Lo Sarzi, Maria; Thomazelli, Ana Paula F S; Conchon-Costa, Ivete; Pavanelli, Wander R; Antonelli, Lis R V; Báfica, André; Mansur, Daniel S; Dos Santos, Claudia N Duarte; Bordignon, Juliano

2018-05-15

Dengue virus (DV) infection can cause either a self-limiting flu-like disease or a threatening hemorrhage that may evolve to shock and death. A variety of cell types, such as dendritic cells, monocytes, and B cells, can be infected by DV. However, despite the role of T lymphocytes in the control of DV replication, there remains a paucity of information on possible DV-T cell interactions during the disease course. In the present study, we have demonstrated that primary human naive CD4 + and CD8 + T cells are permissive for DV infection. Importantly, both T cell subtypes support viral replication and secrete viable virus particles. DV infection triggers the activation of both CD4 + and CD8 + T lymphocytes, but preactivation of T cells reduces the susceptibility of T cells to DV infection. Interestingly, the cytotoxicity-inducing protein granzyme A is highly secreted by human CD4 + but not CD8 + T cells after exposure to DV in vitro Additionally, using annexin V and polycaspase assays, we have demonstrated that T lymphocytes, in contrast to monocytes, are resistant to DV-induced apoptosis. Strikingly, both CD4 + and CD8 + T cells were found to be infected with DV in acutely infected dengue patients. Together, these results show that T cells are permissive for DV infection in vitro and in vivo , suggesting that this cell population may be a viral reservoir during the acute phase of the disease. IMPORTANCE Infection by dengue virus (DV) causes a flu-like disease that can evolve to severe hemorrhaging and death. T lymphocytes are important cells that regulate antibody secretion by B cells and trigger the death of infected cells. However, little is known about the direct interaction between DV and T lymphocytes. Here, we show that T lymphocytes from healthy donors are susceptible to infection by DV, leading to cell activation. Additionally, T cells seem to be resistant to DV-induced apoptosis, suggesting a potential role as a viral reservoir in humans. Finally, we show

A Quad-Cantilevered Plate micro-sensor for intracranial pressure measurement.

Science.gov (United States)

Lalkov, Vasko; Qasaimeh, Mohammad A

2017-07-01

This paper proposes a new design for pressure-sensing micro-plate platform to bring higher sensitivity to a pressure sensor based on piezoresistive MEMS sensing mechanism. The proposed design is composed of a suspended plate having four stepped cantilever beams connected to its corners, and thus defined as Quad-Cantilevered Plate (QCP). Finite element analysis was performed to determine the optimal design for sensitivity and structural stability under a range of applied forces. Furthermore, a piezoresistive analysis was performed to calculate sensor sensitivity. Both the maximum stress and the change in resistance of the piezoresistor associated with the QCP were found to be higher compared to previously published designs, and linearly related to the applied pressure as desired. Therefore, the QCP demonstrates greater sensitivity, and could be potentially used as an efficient pressure sensor for intracranial pressure measurement.

Forced wave induced by an atmospheric pressure disturbance moving towards shore

Science.gov (United States)

Chen, Yixiang; Niu, Xiaojing

2018-05-01

Atmospheric pressure disturbances moving over a vast expanse of water can induce different wave patterns, which can be determined by the Froude number Fr. Generally, Fr = 1 is a critical value for the transformation of the wave pattern and the well-known Proudman resonance happens when Fr = 1. In this study, the forced wave induced by an atmospheric pressure disturbance moving over a constant slope from deep sea to shore is numerically investigated. The wave pattern evolves from a concentric-circle type into a triangular type with the increase of the Froude number, as the local water depth decreases, which is in accord with the analysis in the unbounded flat-bottom cases. However, a hysteresis effect has been observed, which implies the obvious amplification of the forced wave induced by a pressure disturbance can not be simply predicted by Fr = 1. The effects of the characteristic parameters of pressure disturbances and slope gradient have been discussed. The results show that it is not always possible to observe significant peak of the maximum water elevation before the landing of pressure disturbances, and a significant peak can be generated by a pressure disturbance with small spatial scale and fast moving velocity over a milder slope. Besides, an extremely high run-up occurs when the forced wave hits the shore, which is an essential threat to coastal security. The results also show that the maximum run-up is not monotonously varying with the increase of disturbance moving speed and spatial scale. There exists a most dangerous speed and scale which may cause disastrous nearshore surge.

A maximum power point tracking for photovoltaic-SPE system using a maximum current controller

Energy Technology Data Exchange (ETDEWEB)

Muhida, Riza [Osaka Univ., Dept. of Physical Science, Toyonaka, Osaka (Japan); Osaka Univ., Dept. of Electrical Engineering, Suita, Osaka (Japan); Park, Minwon; Dakkak, Mohammed; Matsuura, Kenji [Osaka Univ., Dept. of Electrical Engineering, Suita, Osaka (Japan); Tsuyoshi, Akira; Michira, Masakazu [Kobe City College of Technology, Nishi-ku, Kobe (Japan)

2003-02-01

Processes to produce hydrogen from solar photovoltaic (PV)-powered water electrolysis using solid polymer electrolysis (SPE) are reported. An alternative control of maximum power point tracking (MPPT) in the PV-SPE system based on the maximum current searching methods has been designed and implemented. Based on the characteristics of voltage-current and theoretical analysis of SPE, it can be shown that the tracking of the maximum current output of DC-DC converter in SPE side will track the MPPT of photovoltaic panel simultaneously. This method uses a proportional integrator controller to control the duty factor of DC-DC converter with pulse-width modulator (PWM). The MPPT performance and hydrogen production performance of this method have been evaluated and discussed based on the results of the experiment. (Author)

Reactor building 3D-model for evaluating the pressures on concrete regularization and foundation waterproofing membrane

Energy Technology Data Exchange (ETDEWEB)

Mello Junior, Glauco J.T.; Cardoso, Tarcisio de F.; Prates, Carlos L.M. [Eletrobras Termonuclear S.A. - ELETRONUCLEAR, Rio de Janeiro, RJ (Brazil). Gerencia de Analise de Tensoes GAN.T], e-mail: glauco@eletronuclear.gov.br, e-mail: tarci@eletronuclear.gov.br, e-mail: prates@eletronuclear.gov.br

2009-07-01

Angra dos Reis site in Brazil has already 2 operating PWR NPPs. Unit 3, with identical design to Unit 2, also a 1350 MW PWR, is expected to have its construction started in 2009. This new plant shall be founded directly on sound rock. The first step is to prepare this rock surface with a concrete regularization and a foundation waterproofing membrane. This study presents a 3D model approach of the corresponding reactor building to verify the maximum pressure acting on this surface. The 3D model permits to show a more realistic pressure distribution at every foundation specific detail. A static analysis is performed using ANSYS Mechanical Release 11.1. Dead weight, permanent and live loads, Safe Shutdown Earthquake (SSE) combined with Burst Pressure Wave (BPW) from the Feedwater Tank (SSB=SSE+BPW) and differences of temperature are taken into account. Considering all foundation nodes , the pressure distribution on the waterproofing membrane for each load case is obtained for vertical and horizontal directions, which corresponds to compression and tangential reaction loads. The maximum values occur in distinct positions for each load case. The maximum results are obtained according to DIN 25449 (2008) load combination criteria. The results are compared to a simplified analysis performed before, showing a good agreement in global values. (author)

Reactor building 3D-model for evaluating the pressures on concrete regularization and foundation waterproofing membrane

International Nuclear Information System (INIS)

Mello Junior, Glauco J.T.; Cardoso, Tarcisio de F.; Prates, Carlos L.M.

2009-01-01

Angra dos Reis site in Brazil has already 2 operating PWR NPPs. Unit 3, with identical design to Unit 2, also a 1350 MW PWR, is expected to have its construction started in 2009. This new plant shall be founded directly on sound rock. The first step is to prepare this rock surface with a concrete regularization and a foundation waterproofing membrane. This study presents a 3D model approach of the corresponding reactor building to verify the maximum pressure acting on this surface. The 3D model permits to show a more realistic pressure distribution at every foundation specific detail. A static analysis is performed using ANSYS Mechanical Release 11.1. Dead weight, permanent and live loads, Safe Shutdown Earthquake (SSE) combined with Burst Pressure Wave (BPW) from the Feedwater Tank (SSB=SSE+BPW) and differences of temperature are taken into account. Considering all foundation nodes , the pressure distribution on the waterproofing membrane for each load case is obtained for vertical and horizontal directions, which corresponds to compression and tangential reaction loads. The maximum values occur in distinct positions for each load case. The maximum results are obtained according to DIN 25449 (2008) load combination criteria. The results are compared to a simplified analysis performed before, showing a good agreement in global values. (author)

5 CFR 890.1016 - Aggravating and mitigating factors used to determine the length of permissive debarments.

Science.gov (United States)

2010-01-01

... the debarment, or similar acts, had an adverse impact on the physical or mental health or well-being... OFFICE OF PERSONNEL MANAGEMENT (CONTINUED) CIVIL SERVICE REGULATIONS (CONTINUED) FEDERAL EMPLOYEES HEALTH BENEFITS PROGRAM Administrative Sanctions Imposed Against Health Care Providers Permissive Debarments § 890...

Swelling pressure and water absorption property of compacted granular bentonite during water absorption

International Nuclear Information System (INIS)

Oyamada, T.; Komine, H.; Murakami, S.; Sekiguchi, T.; Sekine, I.

2012-01-01

Document available in extended abstract form only. Bentonite is currently planned to be used as buffer materials in engineered barrier of radioactive waste disposal. Granular bentonites are expected as the materials used in constructions as buffer materials by in-situ compaction methods. After applying these buffer materials, it is expected that the condition of the buffer area changes in long-term by the seepage of groundwater into buffer area. Therefore, it is important to understand water movement and swelling behavior of the buffer materials for evaluating the performance of engineered barrier. In this study, we investigated water absorption property and swelling pressure of compacted granular bentonite. Specifically, the process of swelling pressure and amount of water absorption of granular bentonite-GX (Kunigel-GX, produced at the Tsukinuno mine in Japan) were observed by laboratory tests. To discuss the influence of maximum grain size of bentonite particle on swelling pressure and water absorption property, two types of samples were used. One is granular sample which is Bentonite-GX controlled under 2 mm the maximum grain size, the other is milled sample which is Bentonite-GX with the maximum grain size under 0.18 mm by milling with the agate mortar. In addition, the mechanism on the swelling pressure of compacted granular bentonite was considered and discussed. In the cases of granular sample, swelling pressure increases rapidly, then gradually continues to increase up to maximum value. In the cases of milled sample, swelling pressure also increases rapidly at first. However, then its value decreases before progressing of gradual increase continues. Especially, this trend was clearly observed at a relatively low dry density. At the peaks of these curves, the swelling pressure of granular samples is lower than that of milled samples. In addition, the increasing of swelling pressure by the time the peak observed during the process of swelling pressure from

Regional respiratory inflation and deflation pressure-volume curves determined by electrical impedance tomography.

Science.gov (United States)

Frerichs, I; Dargaville, P A; Rimensberger, P C

2013-06-01

Measurement of regional lung volume changes during a quasi-static pressure-volume (PV) manoeuvre using electrical impedance tomography (EIT) could be used to assess regional respiratory system mechanics and to determine optimal ventilator settings in individual patients. Using this approach, we studied regional respiratory system mechanics in healthy and lung-injured animals, before and after surfactant administration during inflation and deflation PV manoeuvres. The comparison of the EIT-derived regional PV curves in ventral, middle and dorsal regions of the right and left lungs showed not only different amounts of hysteresis in these regions but also marked differences among different landmark pressures calculated on the inflation and deflation limbs of the curves. Regional pressures at maximum compliance as well as the lower and upper pressures of maximum compliance change differed between the inflation and deflation and increased from ventral to dorsal regions in all lung conditions. All these pressure values increased in the injured and decreased in the surfactant treated lungs. Examination of regional respiratory system mechanics using EIT enables the assessment of spatial and temporal heterogeneities in the ventilation distribution. Characteristic landmarks on the inflation and especially on the deflation limb of regional PV curves may become useful measures for guiding mechanical ventilation.

Towards the prediction of pre-mining stresses in the European continent. [Estimates of vertical and probable maximum lateral stress in Europe

Energy Technology Data Exchange (ETDEWEB)

Blackwood, R. L.

1980-05-15

There are now available sufficient data from in-situ, pre-mining stress measurements to allow a first attempt at predicting the maximum stress magnitudes likely to occur in a given mining context. The sub-horizontal (lateral) stress generally dominates the stress field, becoming critical to stope stability in many cases. For cut-and-fill mining in particular, where developed fill pressures are influenced by lateral displacement of pillars or stope backs, extraction maximization planning by mathematical modelling techniques demands the best available estimate of pre-mining stresses. While field measurements are still essential for this purpose, in the present paper it is suggested that the worst stress case can be predicted for preliminary design or feasibility study purposes. In the Eurpoean continent the vertical component of pre-mining stress may be estimated by adding 2 MPa to the pressure due to overburden weight. The maximum lateral stress likely to be encountered is about 57 MPa at depths of some 800m to 1000m below the surface.

Characteristics of CO/sub 2/ TE-amplifiers with different uv preionization at superatmospheric pressure with doping additives