[Co-composting of high moisture vegetable waste, flower waste and chicken litter in pilot scale].

Science.gov (United States)

Zhang, Xiangfeng; Wang, Hongtao; Nie, Yongfeng; Qiu, Xiangyang

2003-03-01

Co-composting of different mixture made of vegetable waste, flower waste and chicken litter were studied. The first stage of composting was aerobic static bed based temperature feedback and control via aeration rate regulation. The second stage was window composting. At first stage, the pile was insulated and temperatures of at least 55 degrees C were maintained for a minimum of 3 days. The highest temperature was up to 73.3 degrees C. This is enough to kill pathogens. Moisture of pile decreased from 75% to 56% and organic matter was degraded from 65% to 50% during composting. The value of pH was stable at 8. Analysis of maturity and nutrition of compost showed that end-products of composting ware bio-stable and had abundant nutrition. This shows that co-composting of vegetable waste, flower waste and chicken litter can get high quality compost by optimizing composting process during 45 days. Composting can decrease nonpoint resource of organic solid waste by recycling nutrition to soil and improve fertility of soil.

Developing Soil Moisture Profiles Utilizing Remotely Sensed MW and TIR Based SM Estimates Through Principle of Maximum Entropy

Science.gov (United States)

Mishra, V.; Cruise, J. F.; Mecikalski, J. R.

2015-12-01

Developing accurate vertical soil moisture profiles with minimum input requirements is important to agricultural as well as land surface modeling. Earlier studies show that the principle of maximum entropy (POME) can be utilized to develop vertical soil moisture profiles with accuracy (MAE of about 1% for a monotonically dry profile; nearly 2% for monotonically wet profiles and 3.8% for mixed profiles) with minimum constraints (surface, mean and bottom soil moisture contents). In this study, the constraints for the vertical soil moisture profiles were obtained from remotely sensed data. Low resolution (25 km) MW soil moisture estimates (AMSR-E) were downscaled to 4 km using a soil evaporation efficiency index based disaggregation approach. The downscaled MW soil moisture estimates served as a surface boundary condition, while 4 km resolution TIR based Atmospheric Land Exchange Inverse (ALEXI) estimates provided the required mean root-zone soil moisture content. Bottom soil moisture content is assumed to be a soil dependent constant. Mulit-year (2002-2011) gridded profiles were developed for the southeastern United States using the POME method. The soil moisture profiles were compared to those generated in land surface models (Land Information System (LIS) and an agricultural model DSSAT) along with available NRCS SCAN sites in the study region. The end product, spatial soil moisture profiles, can be assimilated into agricultural and hydrologic models in lieu of precipitation for data scarce regions.Developing accurate vertical soil moisture profiles with minimum input requirements is important to agricultural as well as land surface modeling. Previous studies have shown that the principle of maximum entropy (POME) can be utilized with minimal constraints to develop vertical soil moisture profiles with accuracy (MAE = 1% for monotonically dry profiles; MAE = 2% for monotonically wet profiles and MAE = 3.8% for mixed profiles) when compared to laboratory and field

Numerical and experimental studies on effects of moisture content on combustion characteristics of simulated municipal solid wastes in a fixed bed

International Nuclear Information System (INIS)

Sun, Rui; Ismail, Tamer M.; Ren, Xiaohan; Abd El-Salam, M.

2015-01-01

Highlights: • The effects of moisture content on the burning process of MSW are investigated. • A two-dimensional mathematical model was built to simulate the combustion process. • Temperature distributions, process rates, gas species were measured and simulated. • The The conversion ratio of C/CO and N/NO in MSW are inverse to moisture content. - Abstract: In order to reveal the features of the combustion process in the porous bed of a waste incinerator, a two-dimensional unsteady state model and experimental study were employed to investigate the combustion process in a fixed bed of municipal solid waste (MSW) on the combustion process in a fixed bed reactor. Conservation equations of the waste bed were implemented to describe the incineration process. The gas phase turbulence was modeled using the k–ε turbulent model and the particle phase was modeled using the kinetic theory of granular flow. The rate of moisture evaporation, devolatilization rate, and char burnout was calculated according to the waste property characters. The simulation results were then compared with experimental data for different moisture content of MSW, which shows that the incineration process of waste in the fixed bed is reasonably simulated. The simulation results of solid temperature, gas species and process rate in the bed are accordant with experimental data. Due to the high moisture content of fuel, moisture evaporation consumes a vast amount of heat, and the evaporation takes up most of the combustion time (about 2/3 of the whole combustion process). The whole bed combustion process reduces greatly as MSW moisture content increases. The experimental and simulation results provide direction for design and optimization of the fixed bed of MSW

Numerical and experimental studies on effects of moisture content on combustion characteristics of simulated municipal solid wastes in a fixed bed

Energy Technology Data Exchange (ETDEWEB)

Sun, Rui, E-mail: Sunsr@hit.edu.cn [School of Energy Science and Engineering, Harbin Institute of Technology, 92, West Dazhi Street, Harbin 150001 (China); Ismail, Tamer M., E-mail: temoil@aucegypt.edu [Department of Mechanical Engineering, Suez Canal University, Ismailia (Egypt); Ren, Xiaohan [School of Energy Science and Engineering, Harbin Institute of Technology, 92, West Dazhi Street, Harbin 150001 (China); Abd El-Salam, M. [Department of Basic Science, Cairo University, Giza (Egypt)

2015-05-15

Highlights: • The effects of moisture content on the burning process of MSW are investigated. • A two-dimensional mathematical model was built to simulate the combustion process. • Temperature distributions, process rates, gas species were measured and simulated. • The The conversion ratio of C/CO and N/NO in MSW are inverse to moisture content. - Abstract: In order to reveal the features of the combustion process in the porous bed of a waste incinerator, a two-dimensional unsteady state model and experimental study were employed to investigate the combustion process in a fixed bed of municipal solid waste (MSW) on the combustion process in a fixed bed reactor. Conservation equations of the waste bed were implemented to describe the incineration process. The gas phase turbulence was modeled using the k–ε turbulent model and the particle phase was modeled using the kinetic theory of granular flow. The rate of moisture evaporation, devolatilization rate, and char burnout was calculated according to the waste property characters. The simulation results were then compared with experimental data for different moisture content of MSW, which shows that the incineration process of waste in the fixed bed is reasonably simulated. The simulation results of solid temperature, gas species and process rate in the bed are accordant with experimental data. Due to the high moisture content of fuel, moisture evaporation consumes a vast amount of heat, and the evaporation takes up most of the combustion time (about 2/3 of the whole combustion process). The whole bed combustion process reduces greatly as MSW moisture content increases. The experimental and simulation results provide direction for design and optimization of the fixed bed of MSW.

Study of incorporation of casting wastes in soil-cement blocks

International Nuclear Information System (INIS)

Folmann, R.; Malkowski, W.; Valentina, L.V.D.; Folgureras, M.V.

2011-01-01

Soil-cement bricks are an ecological alternative to conventional ones because they don't need to be burned to gain strength. This study examines the technical possibility of reuse of foundry sand as fine aggregate in soil-cement. The raw materials were characterized by X-ray diffraction, thermal analysis and particle size. The foundry sand wastes were mixed at different levels to soil and cement. Compaction tests were performed to define the mixtures at optimum moisture content corresponding to the maximum density. Isothermal Conduction Calorimeter was performed to study the influence of waste in the cement hydration reaction. The results indicate that the addition of foundry sand waste decreases the optimum moisture content and increases the maximum density without significantly affecting the cement set. (author)

Biodrying process: A sustainable technology for treatment of municipal solid waste with high moisture content.

Science.gov (United States)

Tom, Asha P; Pawels, Renu; Haridas, Ajit

2016-03-01

Municipal solid waste with high moisture content is the major hindrance in the field of waste to energy conversion technologies and here comes the importance of biodrying process. Biodrying is a convective evaporation process, which utilizes the biological heat developed from the aerobic reactions of organic components. The numerous end use possibilities of the output are making the biodrying process versatile, which is possible by achieving the required moisture reduction, volume reduction and bulk density enhancement through the effective utilization of biological heat. In the present case study the detailed research and development of an innovative biodrying reactor has been carried out for the treatment of mixed municipal solid waste with high moisture content. A pilot scale biodrying reactor of capacity 565 cm(3) was designed and set up in the laboratory. The reactor dimensions consisted of an acrylic chamber of 60 cm diameter and 200 cm height, and it was enveloped by an insulation chamber. The insulation chamber was provided to minimise the heat losses through the side walls of the reactor. It simulates the actual condition in scaling up of the reactor, since in bigger scale reactors the heat losses through side walls will be negligible while comparing the volume to surface area ratio. The mixed municipal solid waste with initial moisture content of 61.25% was synthetically prepared in the laboratory and the reactor was fed with 109 kg of this substrate. Aerobic conditions were ensured inside the reactor chamber by providing the air at a constant rate of 40 litre per minute, and the direction of air flow was from the specially designed bottom air chamber to the reactor matrix top. The self heating inside reactor matrix was assumed in the range of 50-60°C during the design stage. Innovative biodrying reactor was found to be efficiently working with the temperature inside the reactor matrix rising to a peak value of 59°C by the fourth day of experiment (the

A novel shredder for municipal solid waste (MSW): influence of feed moisture on breakage performance.

Science.gov (United States)

Luo, Siyi; Xiao, Bo; Xiao, Lei

2010-08-01

A novel MSW shredder was presented but many aspects of the shredder have not been fully characterized. The feed moisture is an important factor that influences crushing performance. This paper focuses on the effect of feed moisture. The breakage of municipal solid waste (MSW) at several moisture levels (0%, 10%, 20%, 40% and 60%) was conducted with a laboratory shredder to investigate the effect of feed moisture on product size distribution and specific energy consumption under two different hydraulic pressures (40 and 60 kg/cm(2)). The results showed definite effects of feed moisture on the product size distribution and specific energy consumption: there is a tendency for the fine production in products to decrease with increasing amounts of water content in the feed; with the increasing feed moisture, specific energy shows an increasing trend; the specific energy and product size distribution under lower hydraulic pressure is more sensitive to the feed moisture than it is under higher hydraulic pressure. (c) 2010. Published by Elsevier Ltd. All rights reserved.

Substrate composition and moisture in composting source-separated human faeces and food waste.

Science.gov (United States)

Niwagaba, C; Nalubega, M; Vinnerås, B; Sundberg, C; Jönsson, H

2009-04-14

The composting of a faeces/ash mixture and food waste in relative proportions of 1:0, 1:1 and 1:3 was studied in three successive experiments conducted in Kampala, Uganda in 216 L reactors insulated with 75 mm styrofoam or not insulated. The faeces/ash mixture alone exceeded 50 degrees C for composting and ways of decreasing substrate moisture should be investigated. The results obtained are applicable to the management of small- to medium-scale composting of faeces/ash and food waste at household and institution levels, e.g. schools and restaurants.

A simplified model of saltcake moisture distribution. Letter report

International Nuclear Information System (INIS)

Simmons, C.S.

1995-09-01

This letter report describes the formulation of a simplified model for finding the moisture distribution in a saltcake waste profile that has been stabilized by pumping out the drainable interstitial liquid. The model is based on assuming that capillarity mainly governs the distribution of moisture in the porous saltcake waste. A stead upward flow of moisture driven by evaporation from the waste surface is conceptualized to occur for isothermal conditions. To obtain hydraulic parameters for unsaturated conditions, the model is calibrated or matched to the relative saturation distribution as measured by neutron probe scans. The model is demonstrated on Tanks 104-BY and 105-TX as examples. A value of the model is that it identifies the key physical parameters that control the surface moisture content in a waste profile. Moreover, the model can be used to estimate the brine application rate at the waste surface that would raise the moisture content there to a safe level. Thus, the model can be applied to help design a strategy for correcting the moisture conditions in a saltcake waste tank

Free Moisture in GT-73 Resin Waste Generated from the Effluent Treatment Facility

International Nuclear Information System (INIS)

Kaplan, D.I.

2002-01-01

Solid Waste Division is presently evaluating whether to transfer spent resin generated from the Effluent Treatment Facility (ETF) to the Nevada Test Site (NTS). One of the criteria for the waste to be accepted at the NTS is that the waste must not contain more than 1 vol-percent free liquid. This criterion reduces the amount of liquid, a primary vector for subsurface contaminant migration (along with colloids), introduced into the repository. This criterion also serves to reduce the chance of an accidental spill during transport of the waste to the NTS. On December 15, 1997, a shipment from Fernald to the NTS leaked some liquid waste onto a highway in Kingman, Arizona, resulting in a Type B Accident Investigation. The direct cause of the leak was attributed to broken welds related to the use of substandard containers. The overall objective of this study was to provide guidance as to whether the spent GT-73 resin would meet the free moisture WAC set by the NTS

Investigation of remote sensing scale up for hot cell waste tank applications. CPAC optical moisture monitoring

International Nuclear Information System (INIS)

Jones, P.L.

1994-01-01

This report discusses work done to investigate the feasibility of using non-contact optical absorption to remotely sense the surface moisture content of salt cake materials. Optical measurements were made in a dimensionally scaled setup to investigate this technique for in-situ waste tank applications. Moisture measurements were obtained from BY-104 simulant samples with 0 wt%, 10 wt%, and 20 wt% moisture content using the back-scattered light from a pulsed infrared optical parametric converter (OPC) laser source operating from 1.51 to 2.12 micron. An InGaAs detector, with 0.038 steradian solid angle (hemisphere = 6.28 steradians) collection angle was used to detect the back-scattered light. This work indicated that there was sufficient back-scatter from the BY-104 material to provide an indication of the surface moisture content

Moisture monitoring and control system engineering study

International Nuclear Information System (INIS)

Carpenter, K.E.; Fadeff, J.G.

1995-01-01

During the past 50 years, a wide variety of chemical compounds have been placed in the 149 single-shell tanks (SSTS) on the Hanford Site. A concern relating to chemical stability, chemical control, and safe storage of the waste is the potential for propagating reactions as a result of ferrocyanide-oxidizer and organic-oxidizer concentrations in the SSTS. Propagating reactions in fuel-nitrate mixtures are precluded if the amounts of fuel and moisture present in the waste are within specified limits. Because most credible ignition sources occur near the waste surface, the main emphasis of this study is toward monitoring and controlling moisture in the top 14 cm (5.5 in.) of waste. The purpose of this engineering study is to recommend a moisture monitoring and control system for use in SSTs containing sludge and saltcake. This study includes recommendations for: (1) monitoring and controlling moisture in SSTs; (2) the fundamental design criteria for a moisture monitoring and control system; and (3) criteria for the deployment of a moisture monitoring and control system in hanford Site SSTs. To support system recommendations, technical bases for selecting and using a moisture monitoring and control system are presented. Key functional requirements and a conceptual design are included to enhance system development and establish design criteria

Maximum surface level and temperature histories for Hanford waste tanks

International Nuclear Information System (INIS)

Flanagan, B.D.; Ha, N.D.; Huisingh, J.S.

1994-01-01

Radioactive defense waste resulting from the chemical processing of spent nuclear fuel has been accumulating at the Hanford Site since 1944. This waste is stored in underground waste-storage tanks. The Hanford Site Tank Farm Facilities Interim Safety Basis (ISB) provides a ready reference to the safety envelope for applicable tank farm facilities and installations. During preparation of the ISB, tank structural integrity concerns were identified as a key element in defining the safety envelope. These concerns, along with several deficiencies in the technical bases associated with the structural integrity issues and the corresponding operational limits/controls specified for conduct of normal tank farm operations are documented in the ISB. Consequently, a plan was initiated to upgrade the safety envelope technical bases by conducting Accelerated Safety Analyses-Phase 1 (ASA-Phase 1) sensitivity studies and additional structural evaluations. The purpose of this report is to facilitate the ASA-Phase 1 studies and future analyses of the single-shell tanks (SSTs) and double-shell tanks (DSTs) by compiling a quantitative summary of some of the past operating conditions the tanks have experienced during their existence. This report documents the available summaries of recorded maximum surface levels and maximum waste temperatures and references other sources for more specific data

Managing soil moisture on waste burial sites in arid regions

International Nuclear Information System (INIS)

Anderson, J.E.; Ratzlaff, T.D.; Nowak, R.S.; Markham, O.D.

1993-01-01

In semiarid regions, where potential evapotranspiration greatly exceeds precipitation, it is theoretically possible to preclude water form reaching interred wastes by (i) providing a sufficient cap of soil to store precipitation that falls while plants are dormant and (ii) establishing sufficient plant cover to deplete soil moisture during the growing season, thereby emptying the water storage reservoir of the soil. Here the authors discuss the theory and rationale for such an approach and then present the results of a field study to test its efficacy at the Idaho National Engineering Laboratory (INEL). They examined the capacity of four species of perennial plants to deplete soil moisture on simulated waste trenches and determined the effective water storage capacity of the soil. Those data enabled them to estimate the minimum depth of fill soil required to prevent deep drainage. Any of the species studied can use all of the plant-available soil water, even during a very wet growing season. The water storage capacity of the soil studied is 17% by volume, so a trench cap of 1.6 m of soil should be adequate to store precipitation received at the INEL while plants are dormant. They recommend a fill soil depth of 2 m to provide a margin of safety in case water accumulates in local areas as a result of heavy snow accumulation, subsidence, or runoff. Fill soil requirements and choice of plant species will vary, but the concepts and general approach are applicable to other shallow land burial sites in arid or semiarid regions. 23 refs., 5 figs

Coupling model of aerobic waste degradation considering temperature, initial moisture content and air injection volume.

Science.gov (United States)

Ma, Jun; Liu, Lei; Ge, Sai; Xue, Qiang; Li, Jiangshan; Wan, Yong; Hui, Xinminnan

2018-03-01

A quantitative description of aerobic waste degradation is important in evaluating landfill waste stability and economic management. This research aimed to develop a coupling model to predict the degree of aerobic waste degradation. On the basis of the first-order kinetic equation and the law of conservation of mass, we first developed the coupling model of aerobic waste degradation that considered temperature, initial moisture content and air injection volume to simulate and predict the chemical oxygen demand in the leachate. Three different laboratory experiments on aerobic waste degradation were simulated to test the model applicability. Parameter sensitivity analyses were conducted to evaluate the reliability of parameters. The coupling model can simulate aerobic waste degradation, and the obtained simulation agreed with the corresponding results of the experiment. Comparison of the experiment and simulation demonstrated that the coupling model is a new approach to predict aerobic waste degradation and can be considered as the basis for selecting the economic air injection volume and appropriate management in the future.

Fracture toughness in nuclear waste glasses and ceramics: environmental and radiation effects

International Nuclear Information System (INIS)

Weber, W.J.; Matzke, H.J.

1986-03-01

The effects of atmospheric moisture and radiation damage on fracture properties of nuclear waste glasses and ceramics was investigated by indentation techniques. In nuclear waste glasses, atmospheric moisture has no measurable effect on hardness but decreases the fracture toughness; radiation damage, on the other hand, decreased the hardness and increased the fracture toughness. In nuclear ceramics, self-radiation damage from alpha decay decreased the hardness and elastic modules; the fracture toughness increased with dose to a broad maximum and then decreased slightly with further increases in dose

Analysis and optimal design of moisture sensor for rice grain moisture measurement

Science.gov (United States)

Jain, Sweety; Mishra, Pankaj Kumar; Thakare, Vandana Vikas

2018-04-01

The analysis and design of a microstrip sensor for accurate determination of moisture content (MC) in rice grains based on oven drying technique, this technique is easy, fast and less time-consuming to other techniques. The sensor is designed with low insertion loss, reflection coefficient and maximum gain is -35dB and 5.88dB at 2.68GHz as well as discussed all the parameters such as axial ratio, maximum gain, smith chart etc, which is helpful for analysis the moisture measurement. The variation in percentage of moisture measurement with magnitude and phase of transmission coefficient is investigated at selected frequencies. The microstrip moisture sensor consists of one layer: substrate FR4, thickness 1.638 is simulated by computer simulated technology microwave studio (CST MWS). It is concluded that the proposed sensor is suitable for development as a complete sensor and to estimate the optimum moisture content of rice grains with accurately, sensitivity, compact, versatile and suitable for determining the moisture content of other crops and agriculture products.

LANDFILL OPERATION FOR CARBON SEQUESTRATION AND MAXIMUM METHANE EMISSION CONTROL; FINAL

International Nuclear Information System (INIS)

Don Augenstein; Ramin Yazdani; Rick Moore; Michelle Byars; Jeff Kieffer; Professor Morton Barlaz; Rinav Mehta

2000-01-01

Controlled landfilling is an approach to manage solid waste landfills, so as to rapidly complete methane generation, while maximizing gas capture and minimizing the usual emissions of methane to the atmosphere. With controlled landfilling, methane generation is accelerated to more rapid and earlier completion to full potential by improving conditions (principally moisture, but also temperature) to optimize biological processes occurring within the landfill. Gas is contained through use of surface membrane cover. Gas is captured via porous layers, under the cover, operated at slight vacuum. A field demonstration project has been ongoing under NETL sponsorship for the past several years near Davis, CA. Results have been extremely encouraging. Two major benefits of the technology are reduction of landfill methane emissions to minuscule levels, and the recovery of greater amounts of landfill methane energy in much shorter times, more predictably, than with conventional landfill practice. With the large amount of US landfill methane generated, and greenhouse potency of methane, better landfill methane control can play a substantial role both in reduction of US greenhouse gas emissions and in US renewable energy. The work described in this report, to demonstrate and advance this technology, has used two demonstration-scale cells of size (8000 metric tons[tonnes]), sufficient to replicate many heat and compaction characteristics of larger ''full-scale'' landfills. An enhanced demonstration cell has received moisture supplementation to field capacity. This is the maximum moisture waste can hold while still limiting liquid drainage rate to minimal and safely manageable levels. The enhanced landfill module was compared to a parallel control landfill module receiving no moisture additions. Gas recovery has continued for a period of over 4 years. It is quite encouraging that the enhanced cell methane recovery has been close to 10-fold that experienced with conventional

CPAC moisture study: Phase 1 report on the study of optical spectra calibration for moisture

International Nuclear Information System (INIS)

Veltkamp, D.

1993-01-01

This report discusses work done to investigate the feasibility of using optical spectroscopic methods, combined with multivariate Partial Least Squares (PLS) calibration modeling, to quantitatively predict the moisture content of the crust material in Hanford's waste tank materials. Experiments were conducted with BY-104 simulant material for the 400--1100 nm (VIS), 1100--2500 (NIR), and 400-4000 cm -1 (IR) optical regions. The test data indicated that the NIR optical region, with a single PLS calibration factor, provided the highest accuracy response (better than 0.5 wt %) over a 0--25 wt % moisture range. Issues relating to the preparation of moisture samples with the BY-104 materials and the potential implementation within hot cell and waste tanks are also discussed. The investigation of potential material interferences, including physical and chemical properties, and the scaled demonstration of fiber optic and camera types of applications with simulated waste tanks are outlined as future work tasks

Micrometeorological, evapotranspiration, and soil-moisture data at the Amargosa Desert Research site in Nye County near Beatty, Nevada, 2006-11

Science.gov (United States)

Arthur, Jonathan M.; Johnson, Michael J.; Mayers, C. Justin; Andraski, Brian J.

2012-01-01

This report describes micrometeorological, evapotranspiration, and soil-moisture data collected since 2006 at the Amargosa Desert Research Site adjacent to a low-level radio-active waste and hazardous chemical waste facility near Beatty, Nevada. Micrometeorological data include precipitation, solar radiation, net radiation, air temperature, relative humidity, saturated and ambient vapor pressure, wind speed and direction, barometric pressure, near-surface soil temperature, soil-heat flux, and soil-water content. Evapotranspiration (ET) data include latent-heat flux, sensible-heat flux, net radiation, soil-heat flux, soil temperature, air temperature, vapor pressure, and other principal energy-budget data. Soil-moisture data include periodic measurements of volumetric water-content at experimental sites that represent vegetated native soil, devegetated native soil, and simulated waste disposal trenches - maximum measurement depths range from 5.25 to 29.25 meters. All data are compiled in electronic spreadsheets that are included with this report.

Simulation analysis and ternary diagram of municipal solid waste pyrolysis and gasification based on the equilibrium model.

Science.gov (United States)

Deng, Na; Zhang, Awen; Zhang, Qiang; He, Guansong; Cui, Wenqian; Chen, Guanyi; Song, Chengcai

2017-07-01

A self-sustained municipal solid waste (MSW) pyrolysis-gasification process with self-produced syngas as heat source was proposed and an equilibrium model was established to predict the syngas reuse rate considering variable MSW components. Simulation results indicated that for constant moisture (ash) content, with the increase of ash (moisture) content, syngas reuse rate gradually increased, and reached the maximum 100% when ash (moisture) content was 73.9% (60.4%). Novel ternary diagrams with moisture, ash and combustible as axes were proposed to predict the adaptability of the self-sustained process and syngas reuse rate for waste. For wastes of given components, its position in the ternary diagram can be determined and the syngas reuse rate can be obtained, which will provide guidance for system design. Assuming that the MSW was composed of 100% combustible content, ternary diagram shows that there was a minimum limiting value of 43.8% for the syngas reuse rate in the process. Copyright © 2017. Published by Elsevier Ltd.

Thermoelectric automotive waste heat energy recovery using maximum power point tracking

International Nuclear Information System (INIS)

Yu Chuang; Chau, K.T.

2009-01-01

This paper proposes and implements a thermoelectric waste heat energy recovery system for internal combustion engine automobiles, including gasoline vehicles and hybrid electric vehicles. The key is to directly convert the heat energy from automotive waste heat to electrical energy using a thermoelectric generator, which is then regulated by a DC-DC Cuk converter to charge a battery using maximum power point tracking. Hence, the electrical power stored in the battery can be maximized. Both analysis and experimental results demonstrate that the proposed system can work well under different working conditions, and is promising for automotive industry.

Potential tank waste material anomalies located near the liquid observation wells: Model predicted responses of a neutron moisture detection system

International Nuclear Information System (INIS)

Finfrock, S.H.; Toffer, H.; Watson, W.T.

1994-09-01

Extensive analyses have been completed to demonstrate that a neutron moisture probe can be used to recognize anomalies in materials and geometry surrounding the liquid observation wells (LOWs). Furthermore, techniques can be developed that will permit the interpretation of detector readings, perturbed by the presence of anomalies, as more accurate moisture concentrations. This analysis effort extends the usefulness of a neutron moisture probe system significantly, especially in the complicated geometries and material conditions that may be encountered in the waste tanks. Both static-source and pulsed-source neutron probes were considered in the analyses. Four different detector configurations were investigated: Thermal and epithermal neutron detectors located in both the near and far field

Physical and chemical evaluation of furniture waste briquettes.

Science.gov (United States)

Moreno, Ana Isabel; Font, Rafael; Conesa, Juan A

2016-03-01

Furniture waste is mainly composed of wood and upholstery foam (mostly polyurethane foam). Both of these have a high calorific value, therefore, energy recovery would be an appropriate process to manage these wastes. Nevertheless, the drawback is that the energy content of these wastes is limited due to their low density mainly that of upholstery foam. Densification of separate foam presents difficulties due to its elastic character. The significance of this work lies in obtaining densified material by co-densification of furniture wood waste and polyurethane foam waste. Densification of furniture wood and the co-densification of furniture wood waste with polyurethane foam have been studied. On the one hand, the parameters that have an effect on the quality of the furniture waste briquettes have been analysed, i.e., moisture content, compaction pressure, presence of lignin, etc. The maximum weight percentage of polyurethane foam that can be added with furniture wood waste to obtain durable briquettes and the optimal moisture were determined. On the other hand, some parameters were analysed in order to evaluate the possible effect on the combustion. The chemical composition of waste wood was compared with untreated wood biomass; the higher nitrogen content and the concentration of some metals were the most important differences, with a significant difference of Ti content. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization of Briquette Produced from Tannery Solid Waste

Directory of Open Access Journals (Sweden)

Olatunde Ajani Oyelaran

2017-06-01

Full Text Available Skin processing produces large volumes of wastes, much of which are not utilized but disposed in the landfill. This study explored the possibility of producing briquettes from tannery waste that could be used for heating purposes for cottage factories and domestic cooking. Wastes studied are buffing dust, chrome shavings, fleshing, and hair. The briquette properties tested were moisture content, volatile matter, ash content, fixed carbon content, calorific value, compressive strength, density and durability. The moisture content of the raw materials ranged between 2.04 and 8.37% while the moisture content of the produced briquettes after 19 days of drying ranges between 1.17 and 4.13%. The volatile matter also decreases while the ash content increases after briquetting. The fixed carbon content ranges 73.79 and 93.23%. The heating values of the briquettes also showed a great increased after briquetting of between 19.82 and 21.86 MJ/kg. The compressive strength ranges between 0.17 and 0.21 kN/cm2, the durability ranges between 97.83 and 99.54%. The maximum densities of the briquettes also meet the required specifications of minimum value of 600 kg/m3. The briquettes produced also possess good qualities that make tannery solid waste a materials for production of briquettes for heating and in cottage industries

Effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco

OpenAIRE

Makan, Abdelhadi; Assobhei, Omar; Mountadar, Mohammed

2013-01-01

Abstract This study aimed to evaluate the effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco in terms of internal temperature, produced gases quantity, organic matter conversion rate, and the quality of the final composts. For this purpose, in-vessel bioreactor was designed and used to evaluate both appropriate initial air pressure and appropriate initial moisture content for the composting process. Moreove...

Utilization of small-angle neutron scattering to decide the maximum loading of nuclear waste in cement matrix

International Nuclear Information System (INIS)

Das, Avik; Mazumder, S.; Sen, D.; Yalmali, V.; Shah, J.G.

2014-01-01

Nuclear power plants generate many kinds of hazardous nuclear waste which are needed to be disposed in an eco-friendly manner. Many different waste incarceration techniques have been adapted for managing the nuclear waste of different category of radioactivity. Immobilisation of low and intermediate level radioactive wastes in cement matrix is one of the widely used and cost-effective techniques in waste management. However, loading of nuclear waste in cement matrix can alter the mesoscopic structure of the hydrated cement and hence, it is very important to set the maximum limit of waste loading in cement for providing proper physical isolation to the nuclear waste

Surface Moisture Measurement System Operation and Maintenance Manual

International Nuclear Information System (INIS)

Ritter, G.A.; Pearce, K.L.; Stokes, T.L.

1995-12-01

This operations and maintenance manual addresses deployment, equipment and field hazards, operating instructions, calibration verification, removal, maintenance, and other pertinent information necessary to safely operate and store the Surface Moisture Measurement System (SMMS) and Liquid Observation Well Moisture Measurement System (LOWMMS). These systems were developed primarily in support of Tank Waste Remediation System (TWRS) Safety Programs for moisture measurement in organic and ferrocyanide watch list tanks

Hazards and operability study for the surface moisture monitoring system

International Nuclear Information System (INIS)

Board, B.D.

1996-01-01

The Hanford Nuclear Reservation Tank Farms' underground waste tanks have been used to store liquid radioactive waste from defense materials production since the 1940's. Waste in certain of the tanks may contain material in the form of ferrocyanide or various organic compounds which could potentially be susceptible to condensed phase chemical reactions. Because of the presence of oxidizing materials (nitrate compounds) and heat sources (radioactive decay and chemical reactions), the ferrocyanide or organic material could potentially fuel a propagating exothermic reaction with undesirable consequences. Analysis and experiments indicate that the reaction propagation and/or initiation may be prevented by the presence of sufficient moisture in the waste. Because the reaction would probably be initiated at the surface of the waste, evidence of sufficient moisture concentration would help provide evidence that the tank waste can continue to be safely stored. The Surface Moisture Measurement System (SMMS) was developed to collect data on the surface moisture in the waste by inserting two types of probes (singly) into a waste tank-a neutron probe and an electromagnetic inductance (EMI) probe. The sensor probes will be placed on the surface of the waste utilizing a moveable deployment arm to lower them through an available riser. The movement of the SMMS within the tank will be monitored by a camera lowered through an adjacent riser. The SMMS equipment is the subject of this study. Hazards and Operability Analysis (HAZOP) is a systematic technique for assessing potential hazards and/or operability problems for a new activity. It utilizes a multidiscipline team of knowledgeable individuals in a systematic brainstorming effort. The results of this study will be used as input to an Unreviewed Safety Question determination

Production and characterization refuse derived fuel (RDF) from high organic and moisture contents of municipal solid waste (MSW)

Science.gov (United States)

Dianda, P.; Mahidin; Munawar, E.

2018-03-01

Many cities in developing countries is facing a serious problems to dealing with huge municipal solid waste (MSW) generated. The main approach to manage MSW is causes environmental impact associated with the leachate and landfill gas emissions. On the other hand, the energy available also limited by rapid growth of population and economic development due to shortage of the natural resource. In this study, the potential utilized of MSW to produce refuse derived fuel (RDF) was investigate. The RDF was produced with various organic waste content. Then, the RDF was subjected to laboratory analysis to determine its characteristic including the calorific value. The results shows the moisture content was increased by increasing organic waste content, while the calorific value was found 17-36 MJ/kg. The highest calorific value was about 36 MJ/kg obtained at RDF with 40% organic waste content. This results indicated that the RDF can be use to substitute coal in main burning process and calcinations of cement industry.

Measuring seasonal variations of moisture in a landfill with the partitioning gas tracer test

International Nuclear Information System (INIS)

Han, Byunghyun; Jafarpour, Behnam; Gallagher, Victoria N.; Imhoff, Paul T.; Chiu, Pei C.; Fluman, Daniel A.

2006-01-01

Seven pilot-scale partitioning gas tracer tests (PGTTs) were conducted to assess the accuracy and reproducibility of this method for measuring water in municipal solid waste landfills. Tests were conducted in the same location over a 12-month period, and measured moisture conditions ranged from possible dry waste to refuse with a moisture content of 24.7%. The final moisture content of 24.7% was in reasonable agreement with gravimetric measurements of excavated refuse, where the moisture content was 26.5 ± 6.0CI%. Laboratory tests were used to assess the utility of the PGTT for measuring water in small pores, water sorbed to solid surfaces, and the influence of dry waste on PGTTs. These experiments indicated that when refuse surfaces are not completely solvated with water, PGTTs may produce misleading results (negative estimates) of water saturation and moisture content

Leachate recirculation: moisture content assessment by means of a geophysical technique.

Science.gov (United States)

Guérin, Roger; Munoz, Marie Laure; Aran, Christophe; Laperrelle, Claire; Hidra, Mustapha; Drouart, Eric; Grellier, Solenne

2004-01-01

Bioreactor technology is a waste treatment concept consisting in speeding up the biodegradation of landfilled waste by optimizing its moisture content through leachate recirculation. The measurement of variations in waste moisture content is critical in the design and control of bioreactors. Conventional methods such as direct physical sampling of waste reach their limits due to the interference with the waste matrix. This paper reviews geophysical measurements such as electrical direct current and electromagnetic slingram methods for measuring the electrical conductivity. Electrical conductivity is a property, which is linked to both moisture and temperature and can provide useful indications on the biodegradation environment in the waste mass. The study reviews three site experiments: a first experimentation shows the advantages (correlation between conductive anomaly and water seepage) but also the limits of geophysical interpretation; the two other sites allow the leachate recirculation to be tracked by studying the relative resistivity variation versus time from electrical 2D imaging. Even if some improvements are necessary to consider geophysical measurements as a real bioreactor monitoring tool, results are promising and could lead to the use of electrical 2D imaging in bioreactor designing.

Moisture sorption isotherms and thermodynamic properties of bovine leather

Science.gov (United States)

Fakhfakh, Rihab; Mihoubi, Daoued; Kechaou, Nabil

2018-04-01

This study was aimed at the determination of bovine leather moisture sorption characteristics using a static gravimetric method at 30, 40, 50, 60 and 70 °C. The curves exhibit type II behaviour according to the BET classification. The sorption isotherms fitting by seven equations shows that GAB model is able to reproduce the equilibrium moisture content evolution with water activity for moisture range varying from 0.02 to 0.83 kg/kg d.b (0.9898 thermodynamic properties such as isosteric heat of sorption, sorption entropy, spreading pressure, net integral enthalpy and entropy. Net isosteric heat of sorption and differential entropy were evaluated through direct use of moisture isotherms by applying the Clausius-Clapeyron equation and used to investigate the enthalpy-entropy compensation theory. Both sorption enthalpy and entropy for desorption increase to a maximum with increasing moisture content, and then decrease sharply with rising moisture content. Adsorption enthalpy decreases with increasing moisture content. Whereas, adsorption entropy increases smoothly with increasing moisture content to a maximum of 6.29 J/K.mol. Spreading pressure increases with rising water activity. The net integral enthalpy seemed to decrease and then increase to become asymptotic. The net integral entropy decreased with moisture content increase.

Moisture sorption isotherms of dehydrated whey proteins

OpenAIRE

Suzana Rimac Brnčić; Vesna Lelas; Zoran Herceg; Marija Badanjak

2010-01-01

Moisture sorption isotherms describe the relation between the moisture content of the dry material (food) and relative humidity of the surrounding environment. The data obtained are important in modelling of drying process conditions, packaging and shelf-life stability of food that will provide maximum retaining of aroma, colour and texture as well as nutritive and biological value. The objective of this research was to establish the equilibrium moisture content and water activity, as well as...

Engineering properties of sunflower seed: Effect of dehulling and moisture content

Directory of Open Access Journals (Sweden)

Mudasir Ahmad Malik

2016-12-01

Full Text Available The study diagnosed engineering properties on varying moisture content of sunflower seed and kernel from 7.6 to 25% (wet basis. On increasing moisture, dimensional values increased for both seed and kernel. Bulk density, true density and porosity were found higher for kernel as compared to seed at each moisture content. On increasing the moisture content from 7.6 to 25%, true density, porosity and thousand kernel weight increased. Coefficient of static friction on plywood was found maximum for kernel at 25% moisture content, while it was minimum for seed on glass at 7.6% moisture content. The angle of repose was maximum for kernel as compared to seed. Initial cracking force, average rupture force and average rupture energy for seed and kernel decreased with an increase in the moisture content. The kernel was found to be more resistant to initial cracking than seed.

Summary of fiscal year 1994 near-infrared spectroscopy moisture sensing activities

International Nuclear Information System (INIS)

Reich, F.R.; Johnson, R.E.; Philipp, B.L.; Duncan, J.B.; Schutzenhofer, G.L.

1995-01-01

This report summarizes the work to develop and deploy near-infrared (NIR) moisture sensing technology for application to the Hanford Site's high-level nuclear waste materials. This work is jointly supported by the U.S. Department of Energy's (DOE) EM-50 Office of Technology Development Support and the EM-30 Tank Waste Safety and Tank Waste Remediation Systems Programs. A basic NIR system was developed at the Savannah River Laboratory (SRL) with support from DOE's EM-50 Office. The application of this technology to Hanford's high-level wastes (HLW). Including deployment, is supported by DOE's EM-30 Systems Programs. The need to know the moisture content in HLW is driven by concerns for the safety of underground storage tanks that contain or are suspected of containing ferrocyanide and organic types of materials. The NIR technology has application for both ex situ (hot cell core measurements) and in situ waste tank moisture sensing. The cold test/calibration data in this report was generated as part of the total life cycle development path being followed in the development and deployment of the NIR technology at the Hanford Site

Remote characterization of mixed waste by infrared spectroscopy: Fiscal year 1995 report

International Nuclear Information System (INIS)

Rebagay, T.V.; Reich, F.R.; Dodd, D.A.; Lopez, T.; Watts, J.K.; Cash, R.J.

1995-09-01

This report summarizes development work completed in FY 1995 on near-infrared (NIR) and Fourier Transform Infrared (FTIR) spectroscopy of determining the moisture content and solid species present in Hanford Site high-level waste. In prior fiscal years, the main emphasis was on identification of cyanide species that might be present in the ferrocyanide waste tanks, but the present thrust has been more focused on determining the moisture content of the waste. If sufficient moisture is present in the waste, propagating reactions in reactive waste are precluded, regardless of its fuel content. A prototype hot cell NIR moisture probe is now ready for hot cell deployment to sense moisture contents and homogeneity in tank waste samples

The effect of moisture regimes on the anaerobic degradation of municipal solid waste from Metepec (Mexico)

International Nuclear Information System (INIS)

Hernandez-Berriel, Ma.C.; Marquez-Benavides, L.; Gonzalez-Perez, D.J.; Buenrostro-Delgado, O.

2008-01-01

The State of Mexico, situated in central Mexico, has a population of about 14 million, distributed in approximately 125 counties. Solid waste management represents a serious and ongoing pressure to local authorities. The final disposal site ('El Socavon') does not comply with minimum environmental requirements as no liners or leachate management infrastructure are available. Consequently, leachate composition or the effects of rain water input on municipal solid waste degradation are largely unknown. The aim of this work was to monitor the anaerobic degradation of municipal solid waste (MSW), simulating the water addition due to rainfall, under two different moisture content regimes (70% and 80% humidity). The study was carried out using bioreactors in both laboratory and pilot scales. The variation of organic matter and pH was followed in the solid matrix of the MSW. The leachate produced was used to estimate the field capacity of the MSW and to determine the pH, COD, BOD and heavy metals. Some leachate parameters were found to be within permitted limits, but further research is needed in order to analyze the leachate from lower layers of the disposal site ('El Socavon')

Moisture dependence of radon transport in concrete : Measurements and modeling

NARCIS (Netherlands)

Cozmuta, [No Value; van der Graaf, ER; de Meijer, RJ

2003-01-01

The moisture dependence of the radon-release rate of concrete was measured under well controlled conditions. It was found that the radon-release rate almost linearly increases up to moisture contents of 50 to 60%. At 70 to 80% a maximum was found and for higher moisture contents the radon-release

Simplified method of checking the observance of maximum permissible activity of waste forms to be placed in the Konrad shaft for final waste storage

International Nuclear Information System (INIS)

Berg, H.P.; Piefke, F.

1986-10-01

The requirements to be met by waste forms destined for final storage in the Konrad shaft among others define maximum permissible activity levels which have been determined from the various parts of the safety analyses. For waste forms with very low activity levels, it is suitable to compile all the very specific requirements in one checking list, and to perform the checking as simply as adequate. On the basis of the compilation of requirements defined for normal operation of the storage facility, hypothetical accidents, thermal loads affecting the host rock, and criticality safety, the maximum permissible activities are derived that are to be checked by the simplified control measures explained. The report explains the computer programs for the ANKONA code. (orig.) [de

Assessment of methane production from shredder waste in landfills: The influence of temperature, moisture and metals.

Science.gov (United States)

Fathi Aghdam, Ehsan; Scheutz, Charlotte; Kjeldsen, Peter

2017-05-01

In this study, methane (CH 4 ) production rates from shredder waste (SW) were determined by incubation of waste samples over a period of 230days under different operating conditions, and first-order decay kinetic constants (k-values) were calculated. SW and sterilized SW were incubated under different temperatures (20-25°C, 37°C, and 55°C), moisture contents (35% and 75% w/w) and amounts of inoculum (5% and 30% of the samples wet weight). The biochemical methane potential (BMP) from different types of SW (fresh, old and sieved) was determined and compared. The ability of metals (iron, aluminum, zinc, and copper) contained in SW to provide electrons for methanogens resulting in gas compositions with high CH 4 contents and very low CO 2 contents was investigated. The BMP of SW was 1.5-6.2kg CH 4 /ton waste. The highest BMP was observed in fresh SW samples, while the lowest was observed in sieved samples (fine fraction of SW). Abiotic production of CH 4 was not observed in laboratory incubations. The biotic experiments showed that when the moisture content was 35% w/w and the temperature was 20-25°C, CH 4 production was extremely low. Increasing the temperature from 20-25°C to 37°C resulted in significantly higher CH 4 production while increasing the temperature from 37°C to 55°C resulted in higher CH 4 production, but to a lower extent. Increasing the moisture and inoculum content also increased CH 4 production. The k-values were 0.033-0.075yr -1 at room temperature, 0.220-0.429yr -1 at 37°C and 0.235-0.488yr -1 at 55°C, indicating that higher temperatures resulted in higher k-values. It was observed that H 2 can be produced by biocorrosion of iron, aluminum, and zinc and it was shown that produced H 2 can be utilized by hydrogenotrophic methanogens to convert CO 2 to CH 4 . Addition of iron and copper to SW resulted in inhibition of CH 4 production, while addition of aluminum and zinc resulted in higher CH 4 production. This suggested that aluminum and

Comparison between Windrow and Pit Composting of Poultry Wastes, Leaves and Garbage of Municipal Solid Waste in Damghan, Iran

Directory of Open Access Journals (Sweden)

Yaghmaeian K, Malakootian M, Noorisepehr M

2005-01-01

Full Text Available Basic principles of Integrated Solid Waste Management (ISWM are: Reduction, Reuse, Recycling and Recovery (4Rs. Composting as an element of ISWM strategy that can be applied to separately collected or mixed wastes, is a controlled aerobic process carried out by successive microbial populations combining both mesophilic and thermophilic activities and leading to the production of carbon dioxide, water, minerals and stabilized organic matter. In this research, comparing between windrow and pit co-composting methods was studied in the city of Damghan, Iran. Waste proportioning was done based on C/N ratio (about 25:1 and moisture content (about 55%. Mixed wastes were located in windrow and pit with natural aeration tunnel. Sufficient oxygen supply was provided in the piles of compostable materials in two systems through frequent turning of the piles in 7 d intervals during the first month. Temperature reached to maximum level in 10-15 d and then depleted (days: 20-25. It reached to the safety level (about 60˚C based on U.S.EPA and WHO recommendations. Finally, compost was produced with pH=7.7, dark brown color and 30- 35% moisture content. N, P, K, organic matter and organic carbon were measured by standard methods. Results were compared with WHO and U.S.EPA recommendations showing suitable conditions Also it was indicated that pit method was better for maintaining temperature, nitrogen, organic C and organic matter.

Bioenergy Potential from Food Waste in California.

Science.gov (United States)

Breunig, Hanna M; Jin, Ling; Robinson, Alastair; Scown, Corinne D

2017-02-07

Food waste makes up approximately 15% of municipal solid waste generated in the United States, and 95% of food waste is ultimately landfilled. Its bioavailable carbon and nutrient content makes it a major contributor to landfill methane emissions, but also presents an important opportunity for energy recovery. This paper presents the first detailed analysis of monthly food waste generation in California at a county level, and its potential contribution to the state's energy production. Scenarios that rely on excess capacity at existing anaerobic digester (AD) and solid biomass combustion facilities, and alternatives that allow for new facility construction, are developed and modeled. Potential monthly electricity generation from the conversion of gross food waste using a combination of AD and combustion varies from 420 to 700 MW, averaging 530 MW. At least 66% of gross high moisture solids and 23% of gross low moisture solids can be treated using existing county infrastructure, and this fraction increases to 99% of high moisture solids and 55% of low moisture solids if waste can be shipped anywhere within the state. Biogas flaring practices at AD facilities can reduce potential energy production by 10 to 40%.

Development and evaluation of the MTVDI for soil moisture monitoring

Science.gov (United States)

Zhu, Wenbin; Lv, Aifeng; Jia, Shaofeng; Sun, Liang

2017-06-01

Several parameterization schemes have been developed to retrieve the soil moisture information involved in the remotely sensed surface temperature-vegetation index (Ts - VI) space. However, most of them are performed with the constraint of the dry edge of the Ts - VI space to define the maximum water stressed conditions. In view of the subjectivity and uncertainty involved in the determination of the dry edge, a new index termed as the Modified Temperature-Vegetation Dryness Index (MTVDI) was developed in this paper to reduce the reliance of the parameterization scheme on the dry edge. In the parameterization scheme of MTVDI, isopleth lines of soil moisture involved in the feature space were retrieved by the temperature-vegetation index method, and only the maximum surface temperature of bare soil (Tsmax) was indispensable in the definition of maximum water stressed conditions. For evaluation purpose, the MTVDI was demonstrated in the Southern Great Plains region of the U.S. and was compared with two other traditional soil moisture indexes developed under the constraint of dry edge. The comparison confirmed the effectivity of the MTVDI in monitoring the spatial pattern and seasonal variation of soil moisture. Our analyses also suggest that Tsmax, the only parameter needed in the definition of maximum water stressed conditions, can be retrieved directly from the parameterization scheme itself. Therefore, the retrieval of MTVDI can be performed independent of the dry edge, which is a significant improvement to the traditional parameterization schemes of soil moisture from the Ts - VI feature space.

Moisture monitoring of ferrocyanide tanks: An evaluation of methods and tools

International Nuclear Information System (INIS)

Meacham, J.E.; Babad, H.; Toffer, H.

1993-04-01

This report reviews the strengths and limitations of moisture monitoring technologies that could be used for determining moisture concentration in Hanford Site single-shell ferrocyanide waste tanks. Two technologies (neutron diffusion and near-infrared spectroscopy) are being pursued as part of the ferrocyanide program. A third technology, Raman spectroscopy, is in development as a speciation tool at the Westinghouse Hanford Company 222-S Laboratory. The potential application of Raman spectroscopy to moisture monitoring is discussed

Moisture accumulation in a building envelope

Energy Technology Data Exchange (ETDEWEB)

Forest, T.W.; Checkwitch, K.

1988-09-01

In a large number of cases, the failure of a building envelope can be traced to the accumulation of moisture. In a cold winter climate, characteristic of the Canadian prairies, moisture is deposited in the structure by the movement of warm, moist air through the envelope. Tests on the moisture accumulation in a building envelope were initiated in a test house at an Alberta research facility during the 1987/88 heating season. The indoor moisture generation rate was measured and compared with the value inferred from the measured air infiltration rate. With the flue open, the moisture generation rate was approximately 5.5 kg/d of which 0.7 kg/d entered the building envelope; the remainder was exhausted through the flue. With the flue blocked, the moisture generation rate decreased to 3.4 kg/d, while the amount of moisture migrating through the envelope increased to 4.0 kg/d. The moisture accumulation in wall panels located on the north and south face of the test house was also monitored. Moisture was allowed to enter the wall cavity via a hole in the drywall. The fiberglass insulation remained dry throughout the test period. The moisture content of the exterior sheathing of the north panel increased to a maximum of 18% wt in the vicinity of the hole, but quickly dried when the ambient temperatures increased towards the end of the season. The south panel showed very little moisture accumlation due to the effects of solar radiation. 14 refs., 9 figs.

Specification of indoor climate design parameters at the assessment of moisture protective properties of enclosing structures

Directory of Open Access Journals (Sweden)

Kornienko Sergey Valer’evich

2016-11-01

Full Text Available Due to wide implementation of enveloping structures with increased heat-insulation properties in modern construction here appeared a necessity to assess their moisture conditions. Assessment of moisture conditions of enveloping structures is carried out according to maximum allowable moisture state basing on determining the surface of maximum damping. In relation to it the necessity of additional vapour barrier is checked using moisture balance equation. Though the change of indoor climate parameters in premises is not taken into account in moisture balance equations defined for different seasons. The author improves the method of calculating moisture protective parameters of enclosing structures according to the maximum allowable damping state for a year and a period of moisture accumulation. It is shown in this article that accounting of temperature and relative humidity change of inside air allows specifying calculated parameters of indoor climate in residential and office rooms in assessment of moisture protective properties of enclosing structures for the case of an effective enclosing structure with a façade heat-insulation composite system. Coordinates of the maximum moistened surface of the envelope depends on indoor climate design parameters. It is concluded that the increase of requirements for moisture protection of enclosing structures when using design values of temperature and relative humidity of internal air according to the Russian regulation (SP 50.13330.2012 is not always reasonable. Accounting of changes of indoor climate parameters allows more precise assessment of moisture protective properties of enclosing structures during their design.

The experience of burning the high-moistured waste of biomass conversion

Energy Technology Data Exchange (ETDEWEB)

Fincker, F.Z.; Zysin, L.V.; Kubyshkin, I.B. [MGVP Polytechenergo, St. Petersburg (Russian Federation)

1993-12-31

Industrially developed countries have a large stock of operating boiler plants to utilize timber industry waste materials (bagasse, bark, wood chips, hydrolytic lignine, sawdust, etc.) for biogenesis of energy. Standard combustion methods employing a bed or flare process cannot guarantee a reliable and economic boiler plant operation with abruptly changing biomass characteristic features. The moisture content in bark or lignin can vary from 50 to 75% during an hour. Particle sizes can vary from powdered to very large, and can have a hundred thousand times size difference. Large metal and mineral inclusions into the starting fuel also complicate the process. The low-temperature whirling combustion technology developed in Russia was taken as a basic. An economical and stable operation of boilers has been achieved by means of up-to-date vortex chamber aerial dynamics, the use of unique devices of fuel feed and preparation with screening the waste materials into sizes. The firing chamber is equipped with a multi-chamber device where screening and fuel particles preparation with the removal of noncombustible inclusions take place. At presenting the firing chamber with multi-step process of burning is in operation with 20 boilers. The firm {open_quotes}POLYTECHENERGO,{close_quotes} a developer and producer of such equipment, carries out the modernization of the boiler plant without changes in the its thermal circuit. In most of cases no replacement of draught means is needed. Competitive with the proposed low-temperature whirling technological process can be only a fluidized bed process, but due to the complexity in service, low reliability, high energy expenditures, such chambers at present are very few. The capital expenses one existing boilers updating for a fluidized bed process exceed the expenses on a low-temperature whirling process by 15--20 fold.

Investigation of some factors affecting on release of radon-222 from phosphogypsum waste associated with phosphate ore processing.

Science.gov (United States)

Hilal, M A; El Afifi, E M; Nayl, A A

2015-07-01

The aim of this study is oriented to investigate the influence of some physicochemical factors such as radium distribution, grain size, moisture content and chemical constituents on releases of radon-222 from the accumulated phosphogypsum (PG) waste. The emanation fraction, activity concentration in the pore and the surface exhalation rate of radon-222 in the bulk PG waste are 34.5 ± 0.3%, 238.6 ± 7.8 kBq m(-3) and 213 ± 6.9 mBq m(-2) s(-1), respectively. These values were varied and enhanced slightly in the fine grain sizes (F1 factor of 1.05 folds compared to the bulk residue. It was also found that release of radon from residue PG waste was controlled positively by radium (Ra-226), calcium (CaSO4) and strontium (SrO). About 67% of radon release attributed to the grain size below 0.5 mm, while 33% due to the large grain size above 0.5 mm. The emanation fraction of Rn-222 is increased with moisture content and the maximum emanation is ∼43% of moisture of 3-8%. It reduced slowly with the continuous increase in moisture till 20%. Due to PG waste in situ can be enhancing the background to the surround workers and/or public. Therefore, the environmental negative impacts due to release of Rn-222 can be minimized by legislation to restrict its civil uses, or increasing its moisture to ∼10%, or by the particle size separation of the fine fraction containing the high levels of Ra-226 followed by a suitable chemical treatment or disposal; whereas the low release amount can be diluted and used in cement industry, roads or dam construction. Copyright © 2015 Elsevier Ltd. All rights reserved.

Calibration of moisture monitors

International Nuclear Information System (INIS)

Gutierrez, R.L.

1979-02-01

A method for calibrating an aluminum oxide hygrometer against an optical chilled mirror dew-point hygrometer has been established. A theoretical cross-point line of dew points from both hygrometers and a maximum moisture content of 10 ppM/sub v/ are used to define an area for calibrating the sensor probes of the aluminum oxide hygrometer

Plasticity and density-moisture-resistance relations of soils amended with fly ash

Energy Technology Data Exchange (ETDEWEB)

Mapfuno, E.; Chanasyk, D.S. [University of Alberta, Edmonton, AB (Canada). Dept. of Renewable Resources

1998-06-01

The objective of this study was to investigate the impact of fly ash amendments on the plasticity, water retention and penetration resistance-density-moisture relationships of three soils of sandy loam, loam and clay loam textures in order to determine the potential compaction of these soil/fly ash mixtures if they were worked at different moisture ranges. For all three soils the addition of fly ash decreased the plasticity index, but slightly increased the Proctor maximum density. This implies that fly ash amendments reduce the range of moisture within which soils are most susceptible to compaction. However, for the sandy loam and loam textured soils amended with fly ash, cultivation must be avoided at moisture contents close to field capacity since maximum densification occurs at these moisture contents. In all three soils the addition of fly ash increased water retention, especially in the sandy loam. Fly ash amendments increased penetration resistance of the clay loam, but increased penetration resistance of the sandy loam.

Statistical optimization for lipase production from solid waste of vegetable oil industry.

Science.gov (United States)

Sahoo, Rajesh Kumar; Kumar, Mohit; Mohanty, Swati; Sawyer, Matthew; Rahman, Pattanathu K S M; Sukla, Lala Behari; Subudhi, Enketeswara

2018-04-21

The production of biofuel using thermostable bacterial lipase from hot spring bacteria out of low-cost agricultural residue olive oil cake is reported in the present paper. Using a lipase enzyme from Bacillus licheniformis, a 66.5% yield of methyl esters was obtained. Optimum parameters were determined, with maximum production of lipase at a pH of 8.2, temperature 50.8°C, moisture content of 55.7%, and biosurfactant content of 1.693 mg. The contour plots and 3D surface responses depict the significant interaction of pH and moisture content with biosurfactant during lipase production. Chromatographic analysis of the lipase transesterification product was methyl esters, from kitchen waste oil under optimized conditions, generated methyl palmitate, methyl stearate, methyl oleate, and methyl linoleate.

Bioenergy Potential from Food Waste in California

Energy Technology Data Exchange (ETDEWEB)

Breunig, Hanna M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Technologies Area; Jin, Ling [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Technologies Area; Robinson, Alastair [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Technologies Area; Scown, Corinne D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Technologies Area; Joint BioEnergy Inst. (JBEI), Emeryville, CA (United States)

2017-01-25

This paper presents the first detailed analysis of monthly food waste generation in California at a county level, and its potential contribution to the state's energy production. Scenarios that rely on excess capacity at existing anaerobic digester (AD) and solid biomass combustion facilities, and alternatives that allow for new facility construction, are developed and modeled. Potential monthly electricity generation from the conversion of gross food waste using a combination of AD and combustion varies from 420 to 700 MW, averaging 530 MW. At least 66% of gross high moisture solids and 23% of gross low moisture solids can be treated using existing county infrastructure, and this fraction increases to 99% of high moisture solids and 55% of low moisture solids if waste can be shipped anywhere within the state. Biogas flaring practices at AD facilities can reduce potential energy production by 10 to 40%.

Effect of storage conditions on the calorific value of municipal solid waste.

Science.gov (United States)

Nzioka, Antony Mutua; Hwang, Hyeon-Uk; Kim, Myung-Gyun; Yan, Cao Zheng; Lee, Chang-Soo; Kim, Young-Ju

2017-08-01

Storage conditions are considered to be an important factor as far as waste material characteristics are concerned. This experimental investigation was conducted using municipal solid waste (MSW) with a high moisture content and varying composition of organic waste. The objective of this study was to understand the effect of storage conditions and temperature on the moisture content and calorific value of the waste. Samples were subjected to two different storage conditions and investigated at specified temperatures. The composition of sample materials investigated was varied for each storage condition and temperature respectively. Gross calorific value was determined experimentally while net calorific value was calculated using empirical formulas proposed by other researchers. Results showed minimal changes in moisture content as well as in gross and net calorific values when the samples were subjected to sealed storage conditions. Moisture content reduced due to the ventilation process and the rate of moisture removal increased with a rise in storage temperature. As expected, rate of moisture removal had a positive effect on gross and net calorific values. Net calorific values also increased at varying rates with a simultaneous decrease in moisture content. Experimental investigation showed the effectiveness of ventilation in improving the combustion characteristics of the waste.

The influence of moisture content of sand on leach rates from cement and bitumen radioactive waste forms in a shallow ground repository

International Nuclear Information System (INIS)

Lovasic, Z.; Torok, J.; Buckley, L.P.

1992-11-01

Leaching rates from cement and bitumen-conditioned waste in contact with sand were determined with different water content of the sand up to and including saturation. A cylindrical waste form occupied one end of a column, with sand packed in the remainder. Axial radionuclide concentration profiles in the columns were determined several times during the experiment using an automated system consisting of a gamma spectrometer and an optical bench. The migration of 85 Sr, 137 Cs and 60 Co was determined from concentration profiles with time. The diffusion coefficient for 137 Cs in cement varied more than expected with the change of moisture content of sand. The leaching of bitumen waste forms is complex, and has poor reproducibility. When the water content of the sand was below 0.067 mL/mL, no leaching was determined from bitumen waste forms in all of the specimens except one. No clear relationship could be established between leach rate and the water content of sand above 0.18 mL/mL water content

Surface moisture measurement system hardware acceptance test report

Energy Technology Data Exchange (ETDEWEB)

Ritter, G.A., Westinghouse Hanford

1996-05-28

This document summarizes the results of the hardware acceptance test for the Surface Moisture Measurement System (SMMS). This test verified that the mechanical and electrical features of the SMMS functioned as designed and that the unit is ready for field service. The bulk of hardware testing was performed at the 306E Facility in the 300 Area and the Fuels and Materials Examination Facility in the 400 Area. The SMMS was developed primarily in support of Tank Waste Remediation System (TWRS) Safety Programs for moisture measurement in organic and ferrocyanide watch list tanks.

Bioconversion of garden waste, kitchen waste and cow dung into value-added products using earthworm Eisenia fetida.

Science.gov (United States)

Wani, K A; Mamta; Rao, R J

2013-04-01

Solid waste management is a worldwide problem and it is becoming more and more complicated day by day due to rise in population, industrialization and changes in our life style. Transformation of industrial sludges into vermicompost is of double interest: on the one hand, a waste is converted into value added product, and, on the other, it controls a pollutant that is a consequence of increasing industrialization. Garden waste, kitchen waste and cow dung were subjected to recycle through vermicomposting by using the epigeic earthworm Eisenia fetida under field conditions. The pH, moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium in vermicompost was analysed. It was found that moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium was high in cow dung, followed by kitchen waste and garden waste. This study clearly indicates that vermicomposting of garden waste, kitchen waste and cow dung can not only produce a value added produce (vermicomposting) but at the same time reduce the quantity of waste.

Minimizing the Moisture Damage and Drain down of Iraqi SMA Mixtures Using Waste Additives

Directory of Open Access Journals (Sweden)

Ali Al-Hadidy

2013-04-01

Full Text Available This research deals with the viability of using polyester fiber (PF, crumb rubber tire (CRT and cellulose fiber (CF as stabilizing waste additives in producing Iraqi SMA mixtures that sustain drain down phenomenon and moisture damage sensitivity. Different ratios of these additives (0.1, 0.2, and 0.3% by weight of aggregate and filler were mixed with 40/50 paving asphalt by means of dry process. Unmodified and modified SMA mixtures were subjected to drain down, Marshall, static indirect tensile strength, tensile stiffness modulus, static compressive strength, tensile strength ratio and index of retained strength tests. A set of regression equations between these tests were established. In addition, an optimization table based on these tests, which can be used to select the type or amount of additive for any field applications has been determined and reported. The results indicated that the inclusion of these additives in SMA mixtures can satisfy the performance requirement of high temperature and much rain zone.

WASTE STABILIZATION FUNDAMENTALS FOR BIOREACTOR LANDFILLS

Science.gov (United States)

Waste stabilization is the process where putrescible waste is biodegraded by microorganisms resulting in an end-product being a relatively inert substrate (e.g., like compost). When exposed to moisture, biologically stabilized waste should not produce substantial quantitie...

Characterisation of chemical composition and energy content of green waste and municipal solid waste from Greater Brisbane, Australia.

Science.gov (United States)

Hla, San Shwe; Roberts, Daniel

2015-07-01

The development and deployment of thermochemical waste-to-energy systems requires an understanding of the fundamental characteristics of waste streams. Despite Australia's growing interest in gasification of waste streams, no data are available on their thermochemical properties. This work presents, for the first time, a characterisation of green waste and municipal solid waste in terms of chemistry and energy content. The study took place in Brisbane, the capital city of Queensland. The municipal solid waste was hand-sorted and classified into ten groups, including non-combustibles. The chemical properties of the combustible portion of municipal solid waste were measured directly and compared with calculations made based on their weight ratios in the overall municipal solid waste. The results obtained from both methods were in good agreement. The moisture content of green waste ranged from 29% to 46%. This variability - and the tendency for soil material to contaminate the samples - was the main contributor to the variation of samples' energy content, which ranged between 7.8 and 10.7MJ/kg. The total moisture content of food wastes and garden wastes was as high as 70% and 60%, respectively, while the total moisture content of non-packaging plastics was as low as 2.2%. The overall energy content (lower heating value on a wet basis, LHVwb) of the municipal solid waste was 7.9MJ/kg, which is well above the World Bank-recommended value for utilisation in thermochemical conversion processes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Hanford waste tank cone penetrometer

International Nuclear Information System (INIS)

Seda, R.Y.

1995-12-01

A new tool is being developed to characterize tank waste at the Hanford Reservation. This tool, known as the cone penetrometer, is capable of obtaining chemical and physical properties in situ. For the past 50 years, this tool has been used extensively in soil applications and now has been modified for usage in Hanford Underground Storage tanks. These modifications include development of new ''waste'' data models as well as hardware design changes to accommodate the hazardous and radioactive environment of the tanks. The modified cone penetrometer is scheduled to be deployed at Hanford by Fall 1996. At Hanford, the cone penetrometer will be used as an instrumented pipe which measures chemical and physical properties as it pushes through tank waste. Physical data, such as tank waste stratification and mechanical properties, is obtained through three sensors measuring tip pressure, sleeve friction and pore pressure. Chemical data, such as chemical speciation, is measured using a Raman spectroscopy sensor. The sensor package contains other instrumentation as well, including a tip and side temperature sensor, tank bottom detection and an inclinometer. Once the cone penetrometer has reached the bottom of the tank, a moisture probe will be inserted into the pipe. This probe is used to measure waste moisture content, water level, waste surface moisture and tank temperature. This paper discusses the development of this new measurement system. Data from the cone penetrometer will aid in the selection of sampling tools, waste tank retrieval process, and addressing various tank safety issues. This paper will explore various waste models as well as the challenges associated with tank environment

Probable maximum flood control

International Nuclear Information System (INIS)

DeGabriele, C.E.; Wu, C.L.

1991-11-01

This study proposes preliminary design concepts to protect the waste-handling facilities and all shaft and ramp entries to the underground from the probable maximum flood (PMF) in the current design configuration for the proposed Nevada Nuclear Waste Storage Investigation (NNWSI) repository protection provisions were furnished by the United States Bureau of Reclamation (USSR) or developed from USSR data. Proposed flood protection provisions include site grading, drainage channels, and diversion dikes. Figures are provided to show these proposed flood protection provisions at each area investigated. These areas are the central surface facilities (including the waste-handling building and waste treatment building), tuff ramp portal, waste ramp portal, men-and-materials shaft, emplacement exhaust shaft, and exploratory shafts facility

Responses of macropropagated Musa plantlets to transient moisture ...

African Journals Online (AJOL)

Moisture stress causes serious devastating effects on crops ranging from retarded growth, tissue desiccation, and severe yield drop to outright death. In this study, the efficacy of six nursery substrates formulated in varying volume ratios of composted plantain fruit/bunch wastes (PFW), sawdust (SD), poultry manure (PM) and ...

Co-composting of green waste and food waste at low C/N ratio

International Nuclear Information System (INIS)

Kumar, Mathava; Ou, Y.-L.; Lin, J.-G.

2010-01-01

In this study, co-composting of food waste and green waste at low initial carbon to nitrogen (C/N) ratios was investigated using an in-vessel lab-scale composting reactor. The central composite design (CCD) and response surface method (RSM) were applied to obtain the optimal operating conditions over a range of preselected moisture contents (45-75%) and C/N ratios (13.9-19.6). The results indicate that the optimal moisture content for co-composting of food waste and green waste is 60%, and the substrate at a C/N ratio of 19.6 can be decomposed effectively to reduce 33% of total volatile solids (TVS) in 12 days. The TVS reduction can be modeled by using a second-order equation with a good fit. In addition, the compost passes the standard germination index of white radish seed indicating that it can be used as soil amendment.

Bioconversion of garden waste, kitchen waste and cow dung into value-added products using earthworm Eisenia fetida

Science.gov (United States)

Wani, K.A.; Mamta; Rao, R.J.

2013-01-01

Solid waste management is a worldwide problem and it is becoming more and more complicated day by day due to rise in population, industrialization and changes in our life style. Transformation of industrial sludges into vermicompost is of double interest: on the one hand, a waste is converted into value added product, and, on the other, it controls a pollutant that is a consequence of increasing industrialization. Garden waste, kitchen waste and cow dung were subjected to recycle through vermicomposting by using the epigeic earthworm Eisenia fetida under field conditions. The pH, moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium in vermicompost was analysed. It was found that moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium was high in cow dung, followed by kitchen waste and garden waste. This study clearly indicates that vermicomposting of garden waste, kitchen waste and cow dung can not only produce a value added produce (vermicomposting) but at the same time reduce the quantity of waste. PMID:23961230

Moisture estimation in power transformer oil using acoustic signals and spectral kurtosis

International Nuclear Information System (INIS)

Leite, Valéria C M N; Veloso, Giscard F C; Borges da Silva, Luiz Eduardo; Lambert-Torres, Germano; Borges da Silva, Jonas G; Pinto, João Onofre Pereira

2016-01-01

The aim of this paper is to present a new technique for estimating the contamination by moisture in power transformer insulating oil based on the spectral kurtosis analysis of the acoustic signals of partial discharges (PDs). Basically, in this approach, the spectral kurtosis of the PD acoustic signal is calculated and the correlation between its maximum value and the moisture percentage is explored to find a function that calculates the moisture percentage. The function can be easily implemented in DSP, FPGA, or any other type of embedded system for online moisture monitoring. To evaluate the proposed approach, an experiment is assembled with a piezoelectric sensor attached to a tank, which is filled with insulating oil samples contaminated by different levels of moisture. A device generating electrical discharges is submerged into the oil to simulate the occurrence of PDs. Detected acoustic signals are processed using fast kurtogram algorithm to extract spectral kurtosis values. The obtained data are used to find the fitting function that relates the water contamination to the maximum value of the spectral kurtosis. Experimental results show that the proposed method is suitable for online monitoring system of power transformers. (paper)

Moisture Monitoring at Area G, Technical Area 54, Los Alamos National Laboratory, 2016 Status Report

Energy Technology Data Exchange (ETDEWEB)

Levitt, Daniel Glenn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Birdsell, Kay Hanson [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Jennings, Terry L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); French, Sean B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-01-17

Hydrological characterization and moisture monitoring activities provide data required for evaluating the transport of subsurface contaminants in the unsaturated and saturated zones beneath Area G, and for the Area G Performance Assessment and Composite Analysis. These activities have been ongoing at Area G, Technical Area 54 of the Los Alamos National Laboratory since waste disposal operations began in 1957. This report summarizes the hydrological characterization and moisture monitoring activities conducted at Area G. It includes moisture monitoring data collected from 1986 through 2016 from numerous boreholes and access tubes with neutron moisture meters, as well as data collected by automated dataloggers for water content measurement sensors installed in a waste disposal pit cover, and buried beneath the floor of a waste disposal pit. This report is an update of a nearly identical report by Levitt et al., (2015) that summarized data collected through early 2015; this report includes additional moisture monitoring data collected at Pit 31 and the Pit 38 extension through December, 2016. It also includes information from the Jennings and French (2009) moisture monitoring report and includes all data from Jennings and French (2009) and the Draft 2010 Addendum moisture monitoring report (Jennings and French, 2010). For the 2015 version of this report, all neutron logging data, including neutron probe calibrations, were investigated for quality and pedigree. Some data were recalculated using more defensible calibration data. Therefore, some water content profiles are different from those in the Jennings and French (2009) report. All of that information is repeated in this report for completeness. Monitoring and characterization data generally indicate that some areas of the Area G vadose zone are consistent with undisturbed conditions, with water contents of less than five percent by volume in the top two layers of the Bandelier tuff at Area G. These data also

Distributed fiber optic moisture intrusion sensing system

Science.gov (United States)

Weiss, Jonathan D.

2003-06-24

Method and system for monitoring and identifying moisture intrusion in soil such as is contained in landfills housing radioactive and/or hazardous waste. The invention utilizes the principle that moist or wet soil has a higher thermal conductance than dry soil. The invention employs optical time delay reflectometry in connection with a distributed temperature sensing system together with heating means in order to identify discrete areas within a volume of soil wherein temperature is lower. According to the invention an optical element and, optionally, a heating element may be included in a cable or other similar structure and arranged in a serpentine fashion within a volume of soil to achieve efficient temperature detection across a large area or three dimensional volume of soil. Remediation, moisture countermeasures, or other responsive action may then be coordinated based on the assumption that cooler regions within a soil volume may signal moisture intrusion where those regions are located.

Moisture sorption isotherms of dehydrated whey proteins

Directory of Open Access Journals (Sweden)

Suzana Rimac Brnčić

2010-03-01

Full Text Available Moisture sorption isotherms describe the relation between the moisture content of the dry material (food and relative humidity of the surrounding environment. The data obtained are important in modelling of drying process conditions, packaging and shelf-life stability of food that will provide maximum retaining of aroma, colour and texture as well as nutritive and biological value. The objective of this research was to establish the equilibrium moisture content and water activity, as well as monolayer value of two commercial powdered whey protein isolates before and after tribomechanical micronisation and enzymatic hydrolysis, respectively. At the same time it was necessary to evaluate the best moisture sorption isotherm equation to fit the experimental data. The equilibrium moisture contents in investigated samples were determined using standard gravimetric method at 20 °C. The range of water activities was 0.11 to 0.75. The monolayer moisture content was estimated from sorption data using Brunauer-Emmett-Teller (BET and Guggenheim-Anderson-de Boer (GAB models. The results have shown that tribomechanically treated whey protein isolates as well as protein hydrolizates had lower monolayer moisture content values as well as higher corresponding water activity. Therefore, in spite of the fact that they have lower moisture content, they can be storage at higher relative humidity compared to untreated samples. BET model gave better fit to experimental sorption data for a water activity range from 0.11-0.54, while GAB model gave the closest fit for a water activity to 0.75.

Integrity of radioactive waste packages at the Yucca mountain repository

International Nuclear Information System (INIS)

Sandquist, G.; Biaglow, A.; Huber, M.; Jagmin, C.

2004-01-01

Several of the important physical and chemical processes that impact the integrity of the radioactive waste packages planned for disposal at the proposed Repository at Yucca Mountain are examined. These processes are described by the aerodynamic, thermodynamic, and chemical interactions associated with the waste packages. The effects of chemical corrosion, mechanical erosion, temperature distributions throughout the repository environs, interactions of air, water, and solid particles, and radiological and biological influences are addressed. Materials will be exposed to at least 3 conditions threatening the integrity of the waste package: 1) accumulated dust and particles on the package surface and suspended in the air, 2) chemical reactions from deposits on the waste package infrastructure materials and tight contact areas, and crevices, and 3) environmental factors affecting chemical reactions such as moisture, pH, Eh, and radiolysis. All 3 of these conditions can combine and produce damaging impacts upon the thin protective layer on the alloy surface of the waste package. There are certain benefits from the low-temperature operating mode with ambient temperature below 85 Celsius degrees, but the materials could be subjected to a maximum temperature of 180 Celsius degrees which might introduce stress corrosion cracking and high temperature effects

Surface moisture measurement system hardware acceptance test procedure

International Nuclear Information System (INIS)

Ritter, G.A.

1996-01-01

The purpose of this acceptance test procedure is to verify that the mechanical and electrical features of the Surface Moisture Measurement System are operating as designed and that the unit is ready for field service. This procedure will be used in conjunction with a software acceptance test procedure, which addresses testing of software and electrical features not addressed in this document. Hardware testing will be performed at the 306E Facility in the 300 Area and the Fuels and Materials Examination Facility in the 400 Area. These systems were developed primarily in support of Tank Waste Remediation System (TWRS) Safety Programs for moisture measurement in organic and ferrocyanide watch list tanks

Thermodynamic analysis on heavy metals partitioning impacted by moisture during the MSW incineration

International Nuclear Information System (INIS)

Zhang Yanguo; Li Qinghai; Jia Jinyan; Meng Aihong

2012-01-01

Highlights: ► Partitioning of HMs affected by moisture was investigated by thermodynamic analysis. ► Increase in moisture and in temperature was opposite impact on HMs contribution. ► The extent of temperature decreased by increase in moisture determines the impact. - Abstract: A thermodynamic calculation was carried out to predict the behavior and speciation of heavy metals (HMs), Pb, Zn, Cu, and Cd, during municipal solid waste (MSW) incineration with the different moisture levels. The calculation was based on the minimization of the total Gibbs free energy of the multi-components and multi-phases closed system reaching chemical equilibrium. The calculation also indicated the reaction directions and tendencies of HMs components. The impacts of chlorine additives (No PVC, 1%PVC, and 5%PVC) and moisture on the behavior of HMs were investigated at different temperature levels in the system (750 °C, 950 °C, and 1150 °C). Furthermore, because the incineration temperature falls down with the increase in moisture in waste, the co-influence of moisture and temperature in combusting MSW on the HMs was also studied with the given chlorine (as 1%PVC + 0.5%NaCl). The results showed that in the non-chlorine system, the impact of the moisture on Pb, Zn, and Cu was not significant, and the ratio of compound transformation was less than 10%, except the Cd compounds at 950 °C and 1150 °C. In the system with low chlorine (as 1%PVC) at constant temperature, the chlorides of HMs (Cd, Pb, Zn, and Cu) transferred to oxides, and when the content of chlorine rose up (as 5%PVC), the ratio of the chlorides of HMs (Cd, Pb, Zn, and Cu) transferring to oxides fell down noticeably. When the moisture varied together with the temperature, the Zn and Cu compounds transferred from chlorides to oxides with increase in moisture as well as decrease in temperature. At the temperature of 700–1000 °C, the impact of temperature on Pb and Cd was little and the moisture was the main factor

Reliability-Based Modeling of Moisture and Load-Duration Effects

DEFF Research Database (Denmark)

Sørensen, John Dalsgaard; Svensson, Staffan

2005-01-01

Load duration effects with respect to reduction of load bearing capacity are very important for structural timber. This paper describes how the load duration effects combined with moisture content and variations c an be determined on basis of simulation of realizations of the time varying load...... and moisture processes. Permanent and snow load sand moisture variations are considered and stochastic models are formulated in accordance with the load models in the Danish structural codes. A damage accumulation model based on fracture mechanics that accounts for both load duration and moisture effects...... is derived. The parameters in the model are fitted to data relevant for Nordic structural timber using the Maximum Likelihood method. The probability of failure as function of time is estimated for representative limit states based on: a) short term strength and b) long term damage accumulation...

Moisture expansion of ceramic tiles produced using kaolin and granite wastes; Expansao por umidade de revestimentos ceramicos incorporados com residuos de granito e caulim

Energy Technology Data Exchange (ETDEWEB)

Mendonca, A.M.G.D.; Cartaxo, J.M.; Santana, L.N.L; Neves, G.A.; Ferreira, H.C., E-mail: ana.duartemendonca@gmail.com, E-mail: gelmires@dema.ufcg.edu.br, E-mail: lisiane@dema.ufcg.edu.br [Unidade Academica de Engenharia de Materiais, Universidade Federal de Campina Grande,Campina Grande, PB (Brazil); Menezes, R.R. [Departamento de Engenharia de Materiais, Universidade Federal da Paraiba, Joao Pessoa, PB (Brazil)

2012-04-15

Moisture expansion (ME) is the term used to describe the expansion of ceramic materials due to the adsorption of water. ME usually occurs slowly and is relatively small, but, it can damage the ceramic tiles adhesion to the underlayment, craze the glaze and lead to the development of cracks on ceramics bricks. In this work kaolin and granite wastes were incorporated in ceramic compositions aiming study their influence on the ME of ceramic tiles. Raw materials were processed and submitted to characterization: physical and mineralogical by laser diffraction particle size analysis, chemical analysis, thermo differential and thermogravimetric analysis and X-ray diffraction. Results showed that kaolin and granite wastes can be incorporated in ceramic composition because display characteristics similar to conventional not plastic ceramic materials, providing satisfactory ME results when compared to the ME limit value of 0.6 mm/m (0.06%) indicated by the ABNT for ceramic tiles. Compositions containing up to 20% of waste can be produced when firing above 1000 deg C. (author)

Modeling water retention of sludge simulants and actual saltcake tank wastes

International Nuclear Information System (INIS)

Simmons, C.S.

1996-07-01

The Ferrocyanide Tanks Safety Program managed by Westinghouse hanford Company has been concerned with the potential combustion hazard of dry tank wastes containing ferrocyanide chemical in combination with nitrate salts. Pervious studies have shown that tank waste containing greater than 20 percent of weight as water could not be accidentally ignited. Moreover, a sustained combustion could not be propagated in such a wet waste even if it contained enough ferrocyanide to burn. Because moisture content is a key critical factor determining the safety of ferrocyanide-containing tank wastes, physical modeling was performed by Pacific Northwest National laboratory to evaluate the moisture-retaining behavior of typical tank wastes. The physical modeling reported here has quantified the mechanisms by which two main types of tank waste, sludge and saltcake, retain moisture in a tank profile under static conditions. Static conditions usually prevail after a tank profile has been stabilized by pumping out any excess interstitial liquid, which is not naturally retained by the waste as a result of physical forces such as capillarity

Co-composting of vegetable wastes and carton: Effect of carton composition and parameter variations.

Science.gov (United States)

Rawoteea, Soonita Anjeena; Mudhoo, Ackmez; Kumar, Sunil

2017-03-01

The aim of the study was to investigate the effects of carton in the composting process of mixed vegetable wastes using an experimental composter of capacity 80L. Three different mixes were set-up (Mixes 1, 2 and 3) which consisted of vegetable wastes, 2.0kg paper and bulking agents, vegetable wastes, 1.5kg carton and bulking agents, vegetable wastes, 4.5kg carton and bulking agents, respectively. Temperature evolution, pH trends, moisture levels, respiration rates, percentage volatile solids and electrical conductivity were monitored for a period of 50days. The system remained under thermophilic conditions for a very short period due to the small size of the reactor. The three mixes did not exceed a temperature of 55°C, where sanitization takes place by the destruction of pathogens. The highest peak of CO 2 evolution was observed in Mix 2 indicating that maximum microbial degradation took place in that mix. Copyright © 2016. Published by Elsevier Ltd.

Energy recovery from municipal solid waste by refuse derived fuel production in Malaysia

International Nuclear Information System (INIS)

Sanaz Saheri; Noorezlin Ahmad Baseri; Masoud Aghajani Mir; Malmasi Saeed

2010-01-01

Energy recovery from municipal solid waste (MSW) is so beneficial both for the energy and for the positive environmental implications. Mainly related to the saving of primary energy derived from fossil fuel. Malaysia as a fast growing population country has the average amount of municipal solid waste (MSW) generated around 0.5-0.8 kg/person/day and it has been increased to 1.7 kg/person/day in major cities. Regarding characterization exercise, the main parts of the Malaysian MSW were found to be food, paper and plastic, which made up almost 80 % of the waste by weight. Furthermore, the average moisture content of the MSW was about 55 %, making incineration a challenging mission. In addition waste sectors in Malaysia contributes to 1.3 million ton of CH 4 compare to total CH 4 emission which is 2.2 MT. In order to overcome waste problem considering other technical, environmental and economical methods seems to be necessarily. Resource recovery centers recovers the maximum proportion of recyclable and recoverable resources from the mixed municipal solid waste .The resource recovery process itself is one of the step-by-step segregation and elimination of all non-combustibles , and separation of the combustibles in the desired form of fuel for good combustion. Then, a further mechanical separation process converts combustible materials to refuse derived fuel (RDF) with moisture content between 20 and 30 % and an average calorific fuel value of about 3450 kcal/kg. So, the aim of this paper is taking into account resource recovery from waste using refuse derived fuel as a secondary resource with regarding advantages and disadvantages of this kind of energy production in Malaysia as a developing country. (author)

Sustainable biobutanol production from pineapple waste by using Clostridium acetobutylicum B 527: Drying kinetics study.

Science.gov (United States)

Khedkar, Manisha A; Nimbalkar, Pranhita R; Gaikwad, Shashank G; Chavan, Prakash V; Bankar, Sandip B

2017-02-01

Present investigation explores the use of pineapple peel, a food industry waste, for acetone-butanol-ethanol (ABE) production using Clostridium acetobutylicum B 527. Proximate analysis of pineapple peel shows that it contains 35% cellulose, 19% hemicellulose, and 16% lignin on dry basis. Drying experiments on pineapple peel waste were carried out in the temperature range of 60-120°C and experimental drying data was modeled using moisture diffusion control model to study its effect on ABE production. The production of ABE was further accomplished via acid hydrolysis, detoxification, and fermentation process. Maximum total sugar release obtained by using acid hydrolysis was 97g/L with 95-97% and 10-50% removal of phenolics and acetic acid, respectively during detoxification process. The maximum ABE titer obtained was 5.23g/L with 55.6% substrate consumption when samples dried at 120°C were used as a substrate (after detoxification). Copyright © 2016 Elsevier Ltd. All rights reserved.

Maximum flood hazard assessment for OPG's deep geologic repository for low and intermediate level waste

International Nuclear Information System (INIS)

Nimmrichter, P.; McClintock, J.; Peng, J.; Leung, H.

2011-01-01

Ontario Power Generation (OPG) has entered a process to seek Environmental Assessment and licensing approvals to construct a Deep Geologic Repository (DGR) for Low and Intermediate Level Radioactive Waste (L&ILW) near the existing Western Waste Management Facility (WWMF) at the Bruce nuclear site in the Municipality of Kincardine, Ontario. In support of the design of the proposed DGR project, maximum flood stages were estimated for potential flood hazard risks associated with coastal, riverine and direct precipitation flooding. The estimation of lake/coastal flooding for the Bruce nuclear site considered potential extreme water levels in Lake Huron, storm surge and seiche, wind waves, and tsunamis. The riverine flood hazard assessment considered the Probable Maximum Flood (PMF) within the local watersheds, and within local drainage areas that will be directly impacted by the site development. A series of hydraulic models were developed, based on DGR project site grading and ditching, to assess the impact of a Probable Maximum Precipitation (PMP) occurring directly at the DGR site. Overall, this flood assessment concluded there is no potential for lake or riverine based flooding and the DGR area is not affected by tsunamis. However, it was also concluded from the results of this analysis that the PMF in proximity to the critical DGR operational areas and infrastructure would be higher than the proposed elevation of the entrance to the underground works. This paper provides an overview of the assessment of potential flood hazard risks associated with coastal, riverine and direct precipitation flooding that was completed for the DGR development. (author)

Greenhouse gas and ammonia emissions from composting of animal manure and other organic waste products

DEFF Research Database (Denmark)

Chowdhury, Md Albarune

, but information on its effect on GHG emissions, especially nitrous oxide (N2O), is still limited. This thesis investigated the main processes and factors affecting the physicochemical composition of the compost and emissions of GHG and NH3 during composting of animal manure and other organic waste products...... organic wastes has been proposed as a potential strategy to reduce gaseous emissions, and is increasingly being used to handle large volumes of surplus manure in areas of intensive livestock production. Composting appears to have the potential for minimising gaseous emissions from organic wastes....... Laboratory studies showed that differences in the initial physical properties (moisture, bulk density, particle density and air-filled porosity) of separated animal slurry solid fractions (SSF) had a considerable impact on the development of compost maximum temperatures (40-70 o C) and the time required (2...

Trace moisture emissions from heated metal surfaces in hydrogen service

International Nuclear Information System (INIS)

Funke, Hans H.; Yao Jianlong; Raynor, Mark W.

2004-01-01

The formation of trace moisture by exposure of dry heated surfaces of 316 L stainless-steel, Restek Silcosteel registered , and nickel 1/8 in. outer diameter line segments to purified Ar and H 2 was studied using atmospheric pressure ionization mass spectrometry at flow rates of 2 slpm. Prior to H 2 exposure, adsorbed moisture was removed by heating incrementally to 500 deg. C in an argon matrix, where the Restek Silcosteel registered material released a maximum of 50 ppb moisture at 300 deg. C and moisture spikes from the Ni and stainless-steel surfaces reached several 100 ppb. Upon exposure to H 2 , persistent low ppb moisture emissions due to the reduction of surface oxide species were observed at temperatures as low as 100 deg. C. Spikes at 300-500 deg. C ranged from ∼100 ppb for the stainless-steel lines to 400 ppb for the Restek Silcosteel registered material. The observed moisture emissions have to be considered as a potential contamination source for high-purity processes utilizing H 2 purge at elevated temperatures

Sampling procedure in a willow plantation for estimation of moisture content

DEFF Research Database (Denmark)

Nielsen, Henrik Kofoed; Lærke, Poul Erik; Liu, Na

2015-01-01

Heating value and fuel quality of wood is closely connected to moisture content. In this work the variation of moisture content (MC) of short rotation coppice (SRC) willow shoots is described for five clones during one harvesting season. Subsequently an appropriate sampling procedure minimising...... labour costs and sampling uncertainty is proposed, where the MC of a single stem section with the length of 10–50 cm corresponds to the mean shoot moisture content (MSMC) with a bias of maximum 11 g kg−1. This bias can be reduced by selecting the stem section according to the particular clone...

Effect of moisture and freeze-thaw on mechanical properties of CRM asphalt mixture

Energy Technology Data Exchange (ETDEWEB)

Kim, Nak-Seok; Cho, Kee-Ju [Kyonggi University, Suwon(Korea)

2000-06-30

This paper presents the experimental test results on moisture and freeze-thaw resistance of hot mix crumb rubber modified (CRM) asphalt concrete mixture. To compare the differences in mechanical properties of conventional and CRM asphalt concretes, various tests were conducted under different moisture conditions and freeze-thaw cycles. Marshall mix design was also performed to determine the optimum asphalt contents for the both asphalt concrete mixtures. Test results revealed that the moisture and freeze-thaw resistance of CRM asphalt mixture was superior to the conventional asphalt concrete. As a result, it is considered that the utilization of waste tires in asphalt pavements has the potential of minimizing the damage due to the moisture and freeze-thaw. (author). 9 refs., 4 tabs., 8 figs.

A Lagrangian identification of the main sources of moisture affecting northeastern Brazil during its pre-rainy and rainy seasons.

Directory of Open Access Journals (Sweden)

Anita Drumond

Full Text Available This work examines the sources of moisture affecting the semi-arid Brazilian Northeast (NEB during its pre-rainy and rainy season (JFMAM through a Lagrangian diagnosis method. The FLEXPART model identifies the humidity contributions to the moisture budget over a region through the continuous computation of changes in the specific humidity along back or forward trajectories up to 10 days period. The numerical experiments were done for the period that spans between 2000 and 2004 and results were aggregated on a monthly basis. Results show that besides a minor local recycling component, the vast majority of moisture reaching NEB area is originated in the south Atlantic basin and that the nearby wet Amazon basin bears almost no impact. Moreover, although the maximum precipitation in the "Poligono das Secas" region (PS occurs in March and the maximum precipitation associated with air parcels emanating from the South Atlantic towards PS is observed along January to March, the highest moisture contribution from this oceanic region occurs slightly later (April. A dynamical analysis suggests that the maximum precipitation observed in the PS sector does not coincide with the maximum moisture supply probably due to the combined effect of the Walker and Hadley cells in inhibiting the rising motions over the region in the months following April.

Active waste disposal monitoring at the Radioactive Waste Management Complex, Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Hubbell, J.M.

1990-10-01

This report describes an active waste disposal monitoring system proposed to be installed beneath the low-level radioactive disposal site at the Radioactive Waste Management Complex (RWMC), Idaho National Engineering Laboratory, Idaho. The monitoring instruments will be installed while the waste is being disposed. Instruments will be located adjacent to and immediately beneath the disposal area within the unsaturated zone to provide early warning of contaminant movement before contaminants reach the Snake River Plain Aquifer. This study determined the optimum sampling techniques using existing monitoring equipment. Monitoring devices were chosen that provide long-term data for moisture content, movement of gamma-emitting nuclides, and gas concentrations in the waste. The devices will allow leachate collection, pore-water collection, collection of gasses, and access for drilling through and beneath the waste at a later time. The optimum monitoring design includes gas sampling devices above, within, and below the waste. Samples will be collected for methane, tritium, carbon dioxide, oxygen, and volatile organic compounds. Access tubes will be utilized to define the redistribution of radionuclides within, above, and below the waste over time and to define moisture content changes within the waste using spectral and neutron logging, respectively. Tracers will be placed within the cover material and within waste containers to estimate transport times by conservative chemical tracers. Monitoring the vadose zone below, within, and adjacent to waste while it is being buried is a viable monitoring option. 12 refs., 16 figs., 1 tab

Solid waste leach characteristics and contaminant-sediment interactions Volume 2: Contaminant transport under unsaturated moisture contents

International Nuclear Information System (INIS)

Lindenmeier, C.W.; Serne, R.J.; Conca, J.L.

1995-09-01

The objectives of this report and subsequent volumes include describing progress on (1) development and optimization of experimental methods to quantify the release of contaminants from solid wastes and their subsequent interactions with unsaturated sediments and (2) the creation of empirical data that become input parameters to performance assessment (PA) analyses for future Hanford Site disposal units and baseline risk assessments for inactive and existing solid waste disposal units. For this report, efforts focused on developing methodologies to evaluate contaminant transport in Trench 8 (W-5 Burial Ground) sediments under unsaturated (vadose zone) conditions. To accomplish this task, a series of flow-through column tests were run using standard saturated column systems, Wierenga unsaturated column systems (both commercial and modified), and the Unsaturated Flow Apparatus (UFA). The reactants investigated were 85 Sr, 236 U, and 238 U as reactive tracers, and tritium as a non-reactive tracer. Results indicate that for moderately unsaturated conditions (volumetric water contents >50 % of saturation), the Wierenga system performed reasonably well such that long water residence times (50-147 h) were achieved, and reasonably good steady-state flow conditions were maintained. The major drawbacks in using this system for reactive tracer work included (1) the inability to achieve reproducible and constant moisture content below 50% of saturation, (2) the four to six month time required to complete a single test, and (3) the propensity for mechanical failure resulting from laboratory power outages during the prolonged testing period

Analysis of soil moisture memory from observations in Europe

Science.gov (United States)

Orth, R.; Seneviratne, S. I.

2012-08-01

Soil moisture is known to show distinctive persistence characteristics compared to other quantities in the climate system. As soil moisture is governing land-atmosphere feedbacks to a large extent, its persistence can provide potential to improve seasonal climate predictions. So far, many modeling studies have investigated the nature of soil moisture memory, with consistent, but model-dependent results. This study investigates soil moisture memory in long-term observational records based on data from five stations across Europe. We investigate spatial and seasonal variations in soil moisture memory and identify their main climatic drivers. Also, we test an existing framework and introduce an extension thereof to approximate soil moisture memory and evaluate the contributions of its driving processes. At the analyzed five sites, we identify the variability of initial soil moisture divided by that of the accumulated forcing over the considered time frame as a main driver of soil moisture memory that reflects the impact of the precipitation regime and of soil and vegetation characteristics. Another important driver is found to be the correlation of initial soil moisture with subsequent forcing that captures forcing memory as it propagates to the soil and also land-atmosphere interactions. Thereby, the role of precipitation is found to be dominant for the forcing. In contrast to results from previous modeling studies, the runoff and evapotranspiration sensitivities to soil moisture are found to have only a minor influence on soil moisture persistence at the analyzed sites. For the central European sites, the seasonal cycles of soil moisture memory display a maximum in late summer and a minimum in spring. An opposite seasonal cycle is found at the analyzed site in Italy. High soil moisture memory is shown to last up to 40 days in some seasons at most sites. Extremely dry or wet states of the soil tend to increase soil moisture memory, suggesting enhanced prediction

Effect of moisture content on some physical and mechanical properties of juvenile rubberwood (Hevea brasiliensis Muell. Arg.

Directory of Open Access Journals (Sweden)

Buhnnum Kyokong

2003-05-01

Full Text Available Moisture content of rubberwood is an important factor influencing its physical and mechanical behaviours. This research aimed at quantifying effect of moisture content on physical and mechanical properties of juvenile rubberwood core. The specimens at various moisture contents were tested in compression and shear parallel to grain. Information was gathered to determine shrinkage, density and specific gravity of specimens. The equilibrium moisture content determined from desorption experiment, was well described by the Hailwood-Horrobin solution theory. Moisture content of 23+4% best represented the value of apparent fiber saturation point, Mp, determined from physical and mechanical properties data. Above Mp, values of all physical and mechanical properties examined were fairly constant. Maximum volumetric shrinkage from moisture content above Mp to an oven-dry condition was 8.2+1.8%. Specific gravity and density were 0.55+0.03 and 614+30 kg/m3 at 12% moisture content. Below Mp, ultimate compressive stress (UCS parallel to grain, ultimate shear stress parallel to grain, modulus of elasticity (MOE for compression parallel to grain, and shear modulus parallel to grain increased exponentially with decreasing moisture content. Shear strain at fracture and work to fracture of shear parallel to grain were found to increase as moisture content decreased below Mp and attained the maximum values at 20% and 12% moisture content, respectively. The values decreased with further lowering of the level of moisture content. Ultimate compressive stress (UCS parallel to grain was closely correlated with specific gravity and was more sensitive to changes in moisture content at higher specific gravity level.

Effects of moisture content and heat treatment on peroxide value ...

African Journals Online (AJOL)

African Journal of Food, Agriculture, Nutrition and Development ... moisture content and reduced with increasing roasting duration. Analysis of ... Within the studied range, 13 h was the minimum OS recorded while maximum were 63.3 h.

Antibiotics production of cellulosic waste with solid state fermentation by Streptomyces

Energy Technology Data Exchange (ETDEWEB)

Yang, S S [National Taiwan Univ., Taipei (Taiwan, Province of China)

1996-09-01

Cellulosic waste, corncob, was used as a substrate in the production of oxytetracycline by Streptomyces rimosus TM-55 in solid state fermentation. Oxytetracycline was detected on the fourth day, and reached its maximum on the eighth day. During cultivation, the moisture content of substrate increased as incubation being, and pH value increased slightly. Optimal conditions for oxytetracycline production were an initial pH of 5.2 to 6.3, an initial moisture content of 64 to 67%, supplemented with 20% (w/w) rice bran or 1.5 to 2.5% (NH{sub 42} SO{sub 4}) as the sole nitrogen source, 1.0% CaCO{sub 3}, 2% MgSO{sub 4} 7H{sub 2}O, 0.5% KH{sub 2}PO{sub 4}, and 0.6 to 0.8% aspartic acid or lysine, with incubation for 8 days at 25 to 30{sup o}C. Each gram of substrate produced 10 to 11 mg of oxytetracycline. (Author)

GENERALIZATION, FORMULATION AND HEAT CONTENTS OF SIMULATED MSW WITH HIGH MOISTURE CONTENT

Directory of Open Access Journals (Sweden)

A. JOHARI

2012-12-01

Full Text Available This paper presents a generalization technique for the formulation of simulated municipal solid waste. This technique is used for the elimination of the inconsistency in the municipal solid waste (MSW characteristics due to its heterogeneous nature. The compositions of simulated municipal solid waste were formulated from four major municipal waste streams components in Malaysia namely paper, plastic, food and yard waste. The technique produced four simplified waste generalization categories with composition of paper (19%, plastic (25%, food (27% and green waste (29% respectively. Comparative study was conducted for proximate analysis for the determination of volatile matter, fixed carbon and ash content. Ultimate analysis was performed for carbon and hydrogen content. The heat content for simulated and actual municipal solid waste showed good agreement. The moisture content of the simulated municipal solid waste and actual municipal solid waste were established at 52.34% and 61.71% respectively. Overall results were considered to be representative of the actual compositions of municipal solid waste in Malaysia.

Estimating the spatial distribution of soil moisture based on Bayesian maximum entropy method with auxiliary data from remote sensing

Science.gov (United States)

Gao, Shengguo; Zhu, Zhongli; Liu, Shaomin; Jin, Rui; Yang, Guangchao; Tan, Lei

2014-10-01

Soil moisture (SM) plays a fundamental role in the land-atmosphere exchange process. Spatial estimation based on multi in situ (network) data is a critical way to understand the spatial structure and variation of land surface soil moisture. Theoretically, integrating densely sampled auxiliary data spatially correlated with soil moisture into the procedure of spatial estimation can improve its accuracy. In this study, we present a novel approach to estimate the spatial pattern of soil moisture by using the BME method based on wireless sensor network data and auxiliary information from ASTER (Terra) land surface temperature measurements. For comparison, three traditional geostatistic methods were also applied: ordinary kriging (OK), which used the wireless sensor network data only, regression kriging (RK) and ordinary co-kriging (Co-OK) which both integrated the ASTER land surface temperature as a covariate. In Co-OK, LST was linearly contained in the estimator, in RK, estimator is expressed as the sum of the regression estimate and the kriged estimate of the spatially correlated residual, but in BME, the ASTER land surface temperature was first retrieved as soil moisture based on the linear regression, then, the t-distributed prediction interval (PI) of soil moisture was estimated and used as soft data in probability form. The results indicate that all three methods provide reasonable estimations. Co-OK, RK and BME can provide a more accurate spatial estimation by integrating the auxiliary information Compared to OK. RK and BME shows more obvious improvement compared to Co-OK, and even BME can perform slightly better than RK. The inherent issue of spatial estimation (overestimation in the range of low values and underestimation in the range of high values) can also be further improved in both RK and BME. We can conclude that integrating auxiliary data into spatial estimation can indeed improve the accuracy, BME and RK take better advantage of the auxiliary

Optimum moisture levels for biodegradation of mortality composting envelope materials.

Science.gov (United States)

Ahn, H K; Richard, T L; Glanville, T D

2008-01-01

Moisture affects the physical and biological properties of compost and other solid-state fermentation matrices. Aerobic microbial systems experience different respiration rates (oxygen uptake and CO2 evolution) as a function of moisture content and material type. In this study the microbial respiration rates of 12 mortality composting envelope materials were measured by a pressure sensor method at six different moisture levels. A wide range of respiration (1.6-94.2mg O2/g VS-day) rates were observed for different materials, with alfalfa hay, silage, oat straw, and turkey litter having the highest values. These four envelope materials may be particularly suitable for improving internal temperature and pathogen destruction rates for disease-related mortality composting. Optimum moisture content was determined based on measurements across a range that spans the maximum respiration rate. The optimum moisture content of each material was observed near water holding capacity, which ranged from near 60% to over 80% on a wet basis for all materials except a highly stabilized soil compost blend (optimum around 25% w.b.). The implications of the results for moisture management and process control strategies during mortality composting are discussed.

Performance assessment of a single-layer moisture store-and-release cover system at a mine waste rock pile in a seasonally humid region (Nova Scotia, Canada).

Science.gov (United States)

Power, Christopher; Ramasamy, Murugan; Mkandawire, Martin

2018-03-03

Cover systems are commonly applied to mine waste rock piles (WRPs) to control acid mine drainage (AMD). Single-layer covers utilize the moisture "store-and-release" concept to first store and then release moisture back to the atmosphere via evapotranspiration. Although more commonly used in semi-arid and arid climates, store-and-release covers remain an attractive option in humid climates due to the low cost and relative simplicity of installation. However, knowledge of their performance in these climates is limited. The objective of this study was to assess the performance of moisture store-and-release covers at full-scale WRPs located in humid climates. This cover type was installed at a WRP in Nova Scotia, Canada, alongside state-of-the-art monitoring instrumentation. Field monitoring was conducted over 5 years to assess key components such as meteorological conditions, cover material water dynamics, net percolation, surface runoff, pore-gas, environmental receptor water quality, landform stability and vegetation. Water balances indicate small reductions in water influx to the waste rock (i.e., 34 to 28% of precipitation) with the diminished AMD release also apparent by small improvements in groundwater quality (increase in pH, decrease in sulfate/metals). Surface water quality analysis and field observations of vegetative/aquatic life demonstrate significant improvements in the surface water receptor. The WRP landform is stable and the vegetative cover is thriving. This study has shown that while a simple store-and-release cover may not be a highly effective barrier to water infiltration in humid climates, it can be used to (i) eliminate contaminated surface water runoff, (ii) minimize AMD impacts to surface water receptor(s), (iii) maintain a stable landform, and (iv) provide a sustainable vegetative canopy.

Selected micrometeorological and soil-moisture data at Amargosa Desert Research Site, an arid site near Beatty, Nye County, Nevada, 1998-2000

Science.gov (United States)

Johnson, Michael J.; Mayers, Charles J.; Andraski, Brian J.

2002-01-01

Selected micrometeorological and soil-moisture data were collected at the Amargosa Desert Research Site adjacent to a low-level radioactive waste and hazardous chemical waste facility near Beatty, Nev., 1998-2000. Data were collected in support of ongoing research studies to improve the understanding of hydrologic and contaminant-transport processes in arid environments. Micrometeorological data include precipitation, air temperature, solar radiation, net radiation, relative humidity, ambient vapor pressure, wind speed and direction, barometric pressure, soil temperature, and soil-heat flux. All micrometeorological data were collected using a 10-second sampling interval by data loggers that output daily mean, maximum, and minimum values, and hourly mean values. For precipitation, data output consisted of daily, hourly, and 5-minute totals. Soil-moisture data included periodic measurements of soil-water content at nine neutron-probe access tubes with measurable depths ranging from 5.25 to 29.75 meters. The computer data files included in this report contain the complete micrometeorological and soil-moisture data sets. The computer data consists of seven files with about 14 megabytes of information. The seven files are in tabular format: (1) one file lists daily mean, maximum, and minimum micrometeorological data and daily total precipitation; (2) three files list hourly mean micrometeorological data and hourly precipitation for each year (1998-2000); (3) one file lists 5-minute precipitation data; (4) one file lists mean soil-water content by date and depth at four experimental sites; and (5) one file lists soil-water content by date and depth for each neutron-probe access tube. This report highlights selected data contained in the computer data files using figures, tables, and brief discussions. Instrumentation used for data collection also is described. Water-content profiles are shown to demonstrate variability of water content with depth. Time-series data are

The contact-temperature ignition (CTI) criteria for propagating chemical reactions including the effect of moisture and application to Hanford waste

International Nuclear Information System (INIS)

Cash, R.J.

1995-01-01

To assure the continued absence of uncontrolled condensed-phase chemical reactions in connection with the Hanford waste materials, efforts have been underway including both theoretical and experimental investigations to clarify the requirements for such reactions. This document defines the differences and requirements for homogeneous runaway and propagating chemical reactions incuding a discussion of general contact-temperature ignition (CTI) condition for propagating reactions that include the effect of moisture. The CTI condition implies that the contact temperature or interface temperature between reacted and unreacted materials must exceed the ignition temperature and is compared to experimental data including both synthetic ferrocyanide and surrogate organic materials. In all cases, the occurrences of ignition accompanied by self-propagating reactions are consistent with the theoretical anticipations of the CTI condition

An integrated approach of composting methodologies for solid waste management

Directory of Open Access Journals (Sweden)

K. Kumaresan

2016-03-01

Full Text Available Organic fraction of solid waste, which upon degradation produces foul smell and generates pathogens, if not properly managed. Composting is not a method of waste disposal but it is a method of waste recycling and used for agricultural purposes. An integrated approach of composting methodology was tested for municipal solid waste management. Solid waste first was composted and after 22 days, was further processed by vermicomposting. Samples were routinely taken for analysis of carbon, nitrogen, moisture content, pH and temperature to determine the quality of composting. Decrease in moisture content to 32.1 %, relative decrease in carbon and nitrogen content were also observed. Among the different types of treatment, municipal solid waste + activated sludge integration showed promising results, followed by vermicomposting municipal solid waste + activated sludge combination, compared to the combinations of dried activated sludge, municipal solid waste + activated sludge semisolid and municipal solid waste + sewage water. Thus, windrow composting followed by vermicomposting gave a better result than other methods. Thus this method would serve as a potential alternative for solid waste management.

An integrated approach of composting methodologies for solid waste management

International Nuclear Information System (INIS)

Kumaresan, K.; Balan, R.; Sridhar, A.; Aravind, J.; Kanmani, P.

2016-01-01

Organic fraction of solid waste, which upon degradation produces foul smell and generates pathogens, if not properly managed. Composting is not a method of waste disposal but it is a method of waste recycling and used for agricultural purposes. An integrated approach of composting methodology was tested for municipal solid waste management. Solid waste first was composted and after 22 days, was further processed by vermicomposting. Samples were routinely taken for analysis of carbon, nitrogen, moisture content, p H and temperature to determine the quality of composting. Decrease in moisture content to 32.1 %, relative decrease in carbon and nitrogen content were also observed. Among the different types of treatment, municipal solid waste + activated sludge integration showed promising results, followed by vermicomposting municipal solid waste + activated sludge combination, compared to the combinations of dried activated sludge, municipal solid waste + activated sludge semisolid and municipal solid waste + sewage water. Thus, windrow composting followed by vermicomposting gave a better result than other methods. Thus this method would serve as a potential alternative for solid waste management.

Diuron mineralisation in a Mediterranean vineyard soil: impact of moisture content and temperature.

Science.gov (United States)

El Sebaï, Talaat; Devers, Marion; Lagacherie, Bernard; Rouard, Nadine; Soulas, Guy; Martin-Laurent, Fabrice

2010-09-01

The diuron-mineralising ability of the microbiota of a Mediterranean vineyard soil exposed each year to this herbicide was measured. The impact of soil moisture and temperature on this microbial activity was assessed. The soil microbiota was shown to mineralise diuron. This mineralising activity was positively correlated with soil moisture content, being negligible at 5% and more than 30% at 20% soil moisture content. According to a double Gaussian model applied to fit the dataset, the optimum temperature/soil moisture conditions were 27.9 degrees C/19.3% for maximum mineralisation rate and 21.9 degrees C/18.3% for maximum percentage mineralisation. The impact of temperature and soil moisture content variations on diuron mineralisation was estimated. A simulated drought period had a suppressive effect on subsequent diuron mineralisation. This drought effect was more marked when higher temperatures were used to dry (40 degrees C versus 28 degrees C) or incubate (28 degrees C versus 20 degrees C) the soil. The diuron kinetic parameters measured after drought conditions were no longer in accordance with those estimated by the Gaussian model. Although soil microbiota can adapt to diuron mineralisation, its activity is strongly dependent on climatic conditions. It suggests that diuron is not rapidly degraded under Mediterranean climate, and that arable Mediterranean soils are likely to accumulate diuron residues. (c) 2010 Society of Chemical Industry.

PRODUCTION OF NEW BIOMASS/WASTE-CONTAINING SOLID FUELS

Energy Technology Data Exchange (ETDEWEB)

David J. Akers; Glenn A. Shirey; Zalman Zitron; Charles Q. Maney

2001-04-20

CQ Inc. and its team members (ALSTOM Power Inc., Bliss Industries, McFadden Machine Company, and industry advisors from coal-burning utilities, equipment manufacturers, and the pellet fuels industry) addressed the objectives of the Department of Energy and industry to produce economical, new solid fuels from coal, biomass, and waste materials that reduce emissions from coal-fired boilers. This project builds on the team's commercial experience in composite fuels for energy production. The electric utility industry is interested in the use of biomass and wastes as fuel to reduce both emissions and fuel costs. In addition to these benefits, utilities also recognize the business advantage of consuming the waste byproducts of customers both to retain customers and to improve the public image of the industry. Unfortunately, biomass and waste byproducts can be troublesome fuels because of low bulk density, high moisture content, variable composition, handling and feeding problems, and inadequate information about combustion and emissions characteristics. Current methods of co-firing biomass and wastes either use a separate fuel receiving, storage, and boiler feed system, or mass burn the biomass by simply mixing it with coal on the storage pile. For biomass or biomass-containing composite fuels to be extensively used in the U.S., especially in the steam market, a lower cost method of producing these fuels must be developed that includes both moisture reduction and pelletization or agglomeration for necessary fuel density and ease of handling. Further, this method of fuel production must be applicable to a variety of combinations of biomass, wastes, and coal; economically competitive with current fuels; and provide environmental benefits compared with coal. Notable accomplishments from the work performed in Phase I of this project include the development of three standard fuel formulations from mixtures of coal fines, biomass, and waste materials that can be used in

Controlled Landfill Project in Yolo County, California for Environmental Benefits of Waste Stabilization and Minimization of Greenhouse Gas Emissions

Science.gov (United States)

Yazdani, R.; Augenstein, D.; Kieffer, J.; Cohen, K.

2003-12-01

The Department of Public Works of Yolo County, California, USA has been testing an advanced approach to landfill bioreactors, controlled (or "enhanced") landfilling, at its Yolo County Central Landfill site near Davis, CA, since 1994. Overall objectives have been the management of waste landfilling for: (1) rapid completion of total gas generation; (2) maximum, high-efficiency gas capture; (3) waste volume reduction; and (4) maximum greenhouse gas and carbon sequestration benefits. Methane generation is controlled and enhanced through carefully managed moisture additions, and by taking advantage of landfill temperature elevation. The generated landfill methane, an important greenhouse gas, is recovered with high efficiency through extraction from a porous recovery layer beneath a surface geomembrane cover. Instrumentation included a total of 56 moisture and 15 temperature sensors in the two cells, gas flow monitoring by positive displacement gas meters, and accurate quantification of liquid inputs and outputs. Gas composition, waste volume reduction, base hydrostatic head, and a range of environmental compliance parameters has been monitored since 1995. Partitioning gas tracer tests using the injection of two gases at dilute concentrations in the landfill have also been initiated to compute the fraction of pore space occupied by water between the points of tracer injection and tracer measurement. There has been rapid waste volume reduction in the enhanced cell that corresponds to the solids' reduction to gas. Monitoring is planned for the next several years, until stabilization parameters are determined complete. Encouraging performance is indicated by: (1) sensor data; (2) gas generation results; (3) data from landfill cores; and (4) decomposition-related indicators including rapid volume reduction. When data are synthesized, project results have attractive implications for new approaches to landfill management. Over seven-years, methane recoveries have averaged

Research on the drying kinetics of household food waste for the development and optimization of domestic waste drying technique.

Science.gov (United States)

Sotiropoulos, A; Malamis, D; Michailidis, P; Krokida, M; Loizidou, M

2016-01-01

Domestic food waste drying foresees the significant reduction of household food waste mass through the hygienic removal of its moisture content at source. In this manuscript, a new approach for the development and optimization of an innovative household waste dryer for the effective dehydration of food waste at source is presented. Food waste samples were dehydrated with the use of the heated air-drying technique under different air-drying conditions, namely air temperature and air velocity, in order to investigate their drying kinetics. Different thin-layer drying models have been applied, in which the drying constant is a function of the process variables. The Midilli model demonstrated the best performance in fitting the experimental data in all tested samples, whereas it was found that food waste drying is greatly affected by temperature and to a smaller scale by air velocity. Due to the increased moisture content of food waste, an appropriate configuration of the drying process variables can lead to a total reduction of its mass by 87% w/w, thus achieving a sustainable residence time and energy consumption level. Thus, the development of a domestic waste dryer can be proved to be economically and environmentally viable in the future.

Conversion of Waste into Wealth: A Study in Solid Waste Management

Directory of Open Access Journals (Sweden)

T. Janakiram

2010-01-01

Full Text Available Disposal of solid waste has been the talk of the day. An attempt has been made to dispose of the solid waste Jatropha (Kattamanakku. Aerobic composting method was employed. Properly treated solid wastes of different composition were mixed with slurries of cowdung and physicochemical parameters were measured after 30 and 60 days of composting. It was observed that percentages of nitrogen, phosphorous, potassium, sodium, calcium and magnesium increased as time elapsed. Water holding capacity, electrical conductivity and moisture content were found to increase, while pH and C/N ratio have been observed to decrease.

Thermal shock effect on Mechanical and Physical properties of pre-moisture treated GRE composite

Science.gov (United States)

Chakraverty, A. P.; Panda, A. B.; Mohanty, U. K.; Mishra, S. C.; Biswal, B. B.

2018-03-01

Many practical situations may be encountered under which a GFRP (Glass fibre reinforced polymer) composite, during its service life, is exposed to the severities of sudden temperature fluctuations. Moisture absorption of GRE (Glass fibre reinforced epoxy) composites followed by various gradients of temperature fluctuations may cause thermo- mechanical degradation. It is on this context, the hand layed GRE composite samples are exposed to up-thermal shock (-40°C to +50°C) and down-thermal shock (+50°C to -40°C) for various time interval after several periods of moisture (hydrothermal/hygrothermal) conditioning. The thermally shocked GRE specimens are put to 3-point bend test to divulge inter laminar shear strength (ILSS). Least ILSS values are recorded for the samples with maximum period of moisture treatments under with both up-thermal and down-thermal shock conditions. Lower glass transition temperature (Tg) values, as revealed through the low temperature DSC test, are exhibited at maximum durations of both up-thermal and down-thermal shock for the samples with higher periods of hygrothermal/hydrothermal treatments. SEM fractographs of representative GRE specimens after optimum period of moisture treatments and thermal shock show the various modes of failures.

Effects of Moisture Content in Solid Waste Landfills

National Research Council Canada - National Science Library

Eck, Craig

2000-01-01

Solid waste landfills are an extremely complex and heterogeneous environment. Modeling the biodegradation processes within a landfill must involve an understanding of how environmental factors affect these processes...

Historical precipitation predictably alters the shape and magnitude of microbial functional response to soil moisture.

Science.gov (United States)

Averill, Colin; Waring, Bonnie G; Hawkes, Christine V

2016-05-01

Soil moisture constrains the activity of decomposer soil microorganisms, and in turn the rate at which soil carbon returns to the atmosphere. While increases in soil moisture are generally associated with increased microbial activity, historical climate may constrain current microbial responses to moisture. However, it is not known if variation in the shape and magnitude of microbial functional responses to soil moisture can be predicted from historical climate at regional scales. To address this problem, we measured soil enzyme activity at 12 sites across a broad climate gradient spanning 442-887 mm mean annual precipitation. Measurements were made eight times over 21 months to maximize sampling during different moisture conditions. We then fit saturating functions of enzyme activity to soil moisture and extracted half saturation and maximum activity parameter values from model fits. We found that 50% of the variation in maximum activity parameters across sites could be predicted by 30-year mean annual precipitation, an indicator of historical climate, and that the effect is independent of variation in temperature, soil texture, or soil carbon concentration. Based on this finding, we suggest that variation in the shape and magnitude of soil microbial response to soil moisture due to historical climate may be remarkably predictable at regional scales, and this approach may extend to other systems. If historical contingencies on microbial activities prove to be persistent in the face of environmental change, this approach also provides a framework for incorporating historical climate effects into biogeochemical models simulating future global change scenarios. © 2016 John Wiley & Sons Ltd.

Event-scale soil moisture dynamics in open evergreen woodlands of southwest Spain

Science.gov (United States)

Lozano-Parra, F. J.; Schnabel, S.; Gómez-Gutiérrez, Á.

2012-04-01

Rangelands with a disperse tree cover occupy large areas in the southwestern part of the Iberian Pensinsula and are also found in other parts of the Mediterranean. In these grazed, savannah-like ecosystems water constitutes an important limiting factor for vegetation growth because of the strong summer dry period, being annual potential evapotranspiration nearly twice the annual rainfall amount. Previous studies by other authors have found lower values of soil water content below the tree canopy as compared to the open spaces, covered only by herbaceous vegetation. The differences of soil moisture between tree covered and open areas vary along the year, commonly being highest during autumn, low when water content is close to saturation and the inverse during summer. Our studies indicate that the spatial variation of soil moisture is more complex. The main objective of this study is to analyze soil moisture dynamics at the event scale below tree canopies (Quercus ilex) and in the open spaces. Because soils are commonly very shallow (Cambisols) and a high concentration of grass roots is found in the upper five centimetres, soil moisture measurements were carried out at 5, 10, 15 and 30 cm depth. The study area is located in Extremadura. Soil moisture is measured continuously with a time resolution of 30 minutes using capacitive sensors and rainfall is registered in 5-minute intervals. Data from the hydrological year 2010-11 are presented here. The main factors which produced variations in soil moisture in the upper 5 cm were amount and duration of the rainfall event. Rainfall intensity was also significantly related with an increase of the water content. At greater depth (30 cm) soil moisture was more related with antecedent rainfall, as for example the amount of precipitation registered 30 and 45 days prior to the event. Maximum increases produced by a rainstorm were approximately 0.20 m3m-3 in grasslands and 0.17 m3m-3 below tree canopy. However, in the uppermost

A comparative study on per capita waste generation according to a waste collecting system in Korea.

Science.gov (United States)

Oh, Jung Hwan; Lee, Eui-Jong; Oh, Jeong Ik; Kim, Jong-Oh; Jang, Am

2016-04-01

As cities are becoming increasingly aware of problems related to conventional mobile collection systems, automated pipeline-based vacuum collection (AVAC) systems have been introduced in some densely populated urban areas. The reasons are that in addition to cost savings, AVAC systems can be efficient, hygienic, and environmentally friendly. Despite difficulties in making direct comparisons of municipal waste between a conventional mobile collection system and an AVAC system, it is meaningful to measure the quantities in each of these collection methods either in total or on a per capita generation of waste (PCGW, g/(day*capita)) basis. Thus, the aim of this study was to assess the difference in per capita generation of household waste according to the different waste collection methods in Korea. Observations on household waste show that there were considerable differences according to waste collection methods. The value of per capita generation of food waste (PCGF) indicates that a person in a city using AVAC produces 60 % of PCGF (109.58 g/(day*capita)), on average, compared with that of a truck system (173.10 g/(day*capita)) as well as 23 %p less moisture component than that with trucks. The value of per capita generation of general waste (PCGG) in a city with an AVAC system showed 147.73 g/(day*capita), which is 20 % less than that with trucks delivered (185 g/(day*capita)). However, general waste sampled from AVAC showed a 35 %p increased moisture content versus truck delivery.

Modelling maximum canopy conductance and transpiration in ...

African Journals Online (AJOL)

There is much current interest in predicting the maximum amount of water that can be transpired by Eucalyptus trees. It is possible that industrial waste water may be applied as irrigation water to eucalypts and it is important to predict the maximum transpiration rates of these plantations in an attempt to dispose of this ...

Results from simulated contact-handled transuranic waste experiments at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Molecke, M.A.; Sorensen, N.R.; Krumhansl, J.L.

1993-01-01

We conducted in situ experiments with nonradioactive, contact-handled transuranic (CH TRU) waste drums at the Waste Isolation Pilot Plant (WIPP) facility for about four years. We performed these tests in two rooms in rock salt, at WIPP, with drums surrounded by crushed salt or 70 wt % salt/30 wt % bentonite clay backfills, or partially submerged in a NaCl brine pool. Air and brine temperatures were maintained at ∼40C. These full-scale (210-L drum) experiments provided in situ data on: backfill material moisture-sorption and physical properties in the presence of brine; waste container corrosion adequacy; and, migration of chemical tracers (nonradioactive actinide and fission product simulants) in the near-field vicinity, all as a function of time. Individual drums, backfill, and brine samples were removed periodically for laboratory evaluations. Waste container testing in the presence of brine and brine-moistened backfill materials served as a severe overtest of long-term conditions that could be anticipated in an actual salt waste repository. We also obtained relevant operational-test emplacement and retrieval experience. All test results are intended to support both the acceptance of actual TRU wastes at the WIPP and performance assessment data needs. We provide an overview and technical data summary focusing on the WIPP CH TRU envirorunental overtests involving 174 waste drums in the presence of backfill materials and the brine pool, with posttest laboratory materials analyses of backfill sorbed-moisture content, CH TRU drum corrosion, tracer migration, and associated test observations

Evaluation of a Soil Moisture Data Assimilation System Over West Africa

Science.gov (United States)

Bolten, J. D.; Crow, W.; Zhan, X.; Jackson, T.; Reynolds, C.

2009-05-01

A crucial requirement of global crop yield forecasts by the U.S. Department of Agriculture (USDA) International Production Assessment Division (IPAD) is the regional characterization of surface and sub-surface soil moisture. However, due to the spatial heterogeneity and dynamic nature of precipitation events and resulting soil moisture, accurate estimation of regional land surface-atmosphere interactions based sparse ground measurements is difficult. IPAD estimates global soil moisture using daily estimates of minimum and maximum temperature and precipitation applied to a modified Palmer two-layer soil moisture model which calculates the daily amount of soil moisture withdrawn by evapotranspiration and replenished by precipitation. We attempt to improve upon the existing system by applying an Ensemble Kalman filter (EnKF) data assimilation system to integrate surface soil moisture retrievals from the NASA Advanced Microwave Scanning Radiometer (AMSR-E) into the USDA soil moisture model. This work aims at evaluating the utility of merging satellite-retrieved soil moisture estimates with the IPAD two-layer soil moisture model used within the DBMS. We present a quantitative analysis of the assimilated soil moisture product over West Africa (9°N- 20°N; 20°W-20°E). This region contains many key agricultural areas and has a high agro- meteorological gradient from desert and semi-arid vegetation in the North, to grassland, trees and crops in the South, thus providing an ideal location for evaluating the assimilated soil moisture product over multiple land cover types and conditions. A data denial experimental approach is utilized to isolate the added utility of integrating remotely-sensed soil moisture by comparing assimilated soil moisture results obtained using (relatively) low-quality precipitation products obtained from real-time satellite imagery to baseline model runs forced with higher quality rainfall. An analysis of root-zone anomalies for each model

Gaseous waste deposition preventive device for glass melting furnace

International Nuclear Information System (INIS)

Takano, Sueo

1998-01-01

The device of the present invention comprises a heater for heating pressurized air and a moisturizer for mixing steams with the pressurized air heated by the heater to make moisturized pressurized air. Steams are mixed to rise humidity by the moisturizing up to the saturated vapor pressure at the temperature of the heating by heating pressurized air as an object of moisturizing by the heater to prevent dew condensation while increasing the amount of steams to be mixed. With such procedures, moisture enriched pressurized air can be jetted out thereby enabling to prevent deposition of solid materials and crystallized materials of gaseous wastes. (T.M.)

Energy from agricultural animal wastes. Rev. ed.

International Nuclear Information System (INIS)

1994-12-01

This technology status report discusses the production of animal wastes in the UK, and the environmental problems caused by direct use of the waste as fertilisers or disposal by landfilling. The effects of the moisture content of the waste on the choice of technology is examined, and the use of anaerobic digestion for wetter wastes to produce biogas and combustion of dryer wastes to produce heat, power and phosphate- and potash-rich ash are discussed. Market opportunities, and the economics and environmental impacts of both technologies are investigated

Collective impacts of soil moisture and orography on deep convective thunderstorms

Science.gov (United States)

Imamovic, Adel; Schlemmer, Linda; Schär, Christoph

2017-04-01

Thunderstorm activity in many land regions peaks in summer, when surface heat fluxes and the atmospheric moisture content reach an annual maximum. Studies using satellite and ground-based observations have shown that the timing and vigor of summer thunderstorms are influenced by the presence of triggering mechanisms such as soil-moisture heterogeneity or orography. In the current process-based study we aim to dissect the combined impact of soil-moisture and orography on moist convection by using convection-resolving climate simulations with idealized landsurface and orographic conditions. First we systematically investigate the sensitivity of moist convection in absence of orography to a mesoscale soil-moisture anomaly, i.e. a region with drier or moister soil. Consistent with previous studies, a high sensitivity of total rain to soil-moisture anomalies over flat terrain is found. The total rain in the presence of a dry soil-moisture anomaly increases linearly if the soil-moisture anomaly is dried: an anomaly that is 50 % dryer than the reference case with a homogeneous soil-moisture distribution produces up to 40 % more rain. The amplitude of this negative response to the dry soil-moisture anomaly cannot be reproduced by either drying or moistening the soil in the whole domain, even when using unrealistic soil-moisture values. A moist soil anomaly showed little impact on total rain. The triggering effects of the soil-moisture anomalies can be reproduced by an isolated mountain of 250 m height. In order to test to what extent the impact of the soil-moisture anomaly and the mountain are additive, the soil-moisture perturbation method is applied to soil-moisture over the isolated mountain. A 250 m high mountain with drier (moister) soil than its surrounding is found to enhance (suppress) rain amounts. However, the sensitivity of rain amount to the soil-moisture anomaly decreases with the mountain height: A 500 m high mountain is already sufficient to eliminate the

Geohydrology of the unsaturated zone at the burial site for low-level radioactive waste near Beatty, Nye County, Nevada

International Nuclear Information System (INIS)

Nichols, W.D.

1987-01-01

Low-level radioactive solid waste has been buried in trenches at a site near Beatty, NV, since 1962. In 1976, as part of a national program, the US Geological Survey began a study of the geohydrology of the waste burial site to provide a basis for estimating the potential for radionuclide migration in the unsaturated zone beneath the waste burial trenches. The waste burial facility is in the northern Amargosa Desert about 170 kilometers (km) northwest of Las Vegas, NV. The site is underlain by poorly stratified deposits of gravelly or silty sand and sandy gravel, and thick beds of clayey sediments. A numerical analysis demonstrated that a potential exists for deep percolation despite high annual evaporation demands, and provided predictions of the time of year and the antecedent conditions that enhance the probability of deep percolation. Soil moisture profiles obtained monthly over an 18-month period demonstrate that deep percolation does occur. Calculation of downward moisture movement through the waste trench backfill material, on the basis of simplified assumptions, suggests that moisture could have penetrated as much as 6 m below land surface from 1963, when the oldest trenches were closed, to 1980, but that the moisture requirement for such penetration far exceeded the amount of moisture actually available. Steady-state downward movement of moisture at depths greater than 10 m and beneath the waste burial trenches would be on the order of 4 cu m/1,000 yr, assuming a steady flux rate of 0.1 microcentimeter/day. 37 refs., 32 figs., 17 tab

Moisture monitoring in large diameter boreholes

International Nuclear Information System (INIS)

Tyler, S.

1985-01-01

The results of both laboratory and field experiments indicate that the neutron moisture gauge traditionally used in soil physics experiments can be extended for use in large diameter (up to 15 cm) steel-cased boreholes with excellent results. This application will permit existing saturated zone monitoring wells to be used for unsaturated zone monitoring of recharge, redistribution and leak detection from waste disposal facilities. Its applicability to large diameter cased wells also gives the soil physicist and ground-water hydrologist and new set of monitoring points in the unsaturated zone to study recharge and aquifer properties. 6 refs., 6 figs., 2 tabs

Simplex-centroid mixture formulation for optimised composting of kitchen waste.

Science.gov (United States)

Abdullah, N; Chin, N L

2010-11-01

Composting is a good recycling method to fully utilise all the organic wastes present in kitchen waste due to its high nutritious matter within the waste. In this present study, the optimised mixture proportions of kitchen waste containing vegetable scraps (V), fish processing waste (F) and newspaper (N) or onion peels (O) were determined by applying the simplex-centroid mixture design method to achieve the desired initial moisture content and carbon-to-nitrogen (CN) ratio for effective composting process. The best mixture was at 48.5% V, 17.7% F and 33.7% N for blends with newspaper while for blends with onion peels, the mixture proportion was 44.0% V, 19.7% F and 36.2% O. The predicted responses from these mixture proportions fall in the acceptable limits of moisture content of 50% to 65% and CN ratio of 20-40 and were also validated experimentally. Copyright 2010 Elsevier Ltd. All rights reserved.

Source segregation of food waste in office areas: Factors affecting waste generation rates and quality

DEFF Research Database (Denmark)

Edjabou, Vincent Maklawe Essonanawe; Boldrin, Alessio; Scheutz, Charlotte

2015-01-01

Existing legislation mandates that the amount of waste being recycled should be increased. Among others, in its Resource Strategy Plan, the Danish Government decided that at least 60% of food waste generated by the service sector, including in office areas, should be source-sorted and collected...... separately by 2018. To assess the achievability of these targets, source-sorted food waste and residual waste from office areas was collected and weighed on a daily basis during 133 working days. Waste composition analyses were conducted every week to investigate the efficiency of the source-sorting campaign...... and the purity of the source-sorted food waste. The moisture content of source-sorted food waste and residual waste fractions, and potential methane production from source-sorted food waste, was also investigated.Food waste generation equated to 23. ±. 5. kg/employee/year, of which 20. ±. 5. kg...

Selected micrometeorological, soil-moisture, and evapotranspiration data at Amargosa Desert Research Site in Nye County near Beatty, Nevada, 2001-05

Science.gov (United States)

Johnson, Michael J.; Mayers, C. Justin; Garcia, C. Amanda; Andraski, Brian J.

2007-01-01

Selected micrometeorological and soil-moisture data were collected at the Amargosa Desert Research Site adjacent to a low-level radio-active waste and hazardous chemical waste facility near Beatty, Nevada, 2001-05. Evapotranspiration data were collected from February 2002 through the end of December 2005. Data were col-lected in support of ongoing research to improve the understanding of hydrologic and contaminant-transport processes in arid environments. Micrometeorological data include solar radiation, net radiation, air temperature, relative humidity, saturated and ambient vapor pressure, wind speed and direction, barometric pressure, precipitation, near-surface soil temperature, soil-heat flux and soil-water content. All micrometeorological data were collected using a 10-second sampling interval by data loggers that output daily and hourly mean values. Daily maximum and minimum values are based on hourly mean values. Precipitation data output includes daily and hourly totals. Selected soil-moisture profiles at depth include periodic measurements of soil volumetric water-content measurements at nine neutron-probe access tubes to depths ranging from 5.25 to 29.25 meters. Evapotranspiration data include measurement of daily evapotranspiration and 15-minute fluxes of the four principal energy budget components of latent-heat flux, sensible-heat flux, soil-heat flux, and net radiation. Other data collected and used in equations to determine evapotranspiration include temperature and water content of soil, temperature and vapor pressure of air, and covariance values. Evapotranspiration and flux estimates during 15-minute intervals were calculated at a 0.1-second execution interval using the eddy covariance method. Data files included in this report contain the complete micrometeorological, soil-moisture, and evapotranspiration field data sets. These data files are presented in tabular Excel spreadsheet format. This report highlights selected data contained in the

Project W-026, Waste Receiving and Processing (WRAP) Facility Module 1: Maximum possible fire loss (MPFL) decontamination and cleanup estimates. Revision 1

International Nuclear Information System (INIS)

Hinkle, A.W.; Jacobsen, P.H.; Lucas, D.R.

1994-01-01

Project W-026, Waste Receiving and Processing (WRAP) Facility Module 1, a 1991 Line Item, is planned for completion and start of operations in the spring of 1997. WRAP Module 1 will have the capability to characterize and repackage newly generated, retrieved and stored transuranic (TRU), TRU mixed, and suspect TRU waste for shipment to the Waste isolation Pilot Plant (WIPP). In addition, the WRAP Facility Module 1 will have the capability to characterize low-level mixed waste for treatment in WRAP Module 2A. This report documents the assumptions and cost estimates for decontamination and clean-up of a maximum possible fire loss (MPFL) as defined by DOE Order 5480.7A, FIRE PROTECTION. The Order defines MPFL as the value of property, excluding land, within a fire area, unless a fire hazards analysis demonstrates a lesser (or greater) loss potential. This assumes failure of both automatic fire suppression systems and manual fire fighting efforts. Estimates were developed for demolition, disposal, decontamination, and rebuilding. Total costs were estimated to be approximately $98M

Moisture conditions in buildings

DEFF Research Database (Denmark)

Rode, Carsten

2012-01-01

Growth of mould requires the presence of moisture at a certain high level. In a heated indoor environment such moisture levels occur only if there is a reason for the moisture supply. Such moisture can come from the use of the building, because of malfunctioning constructions, or it can be the re......Growth of mould requires the presence of moisture at a certain high level. In a heated indoor environment such moisture levels occur only if there is a reason for the moisture supply. Such moisture can come from the use of the building, because of malfunctioning constructions, or it can...

Conceptual model to determine maximum activity of radioactive waste in near-surface disposal facilities

International Nuclear Information System (INIS)

Iarmosh, I.; Olkhovyk, Yu.

2016-01-01

For development of the management strategy for radioactive waste to be placed in near - surface disposal facilities (NSDF), it is necessary to justify long - term safety of such facilities. Use of mathematical modelling methods for long - term forecasts of radwaste radiation impact and assessment of radiation risks from radionuclides migration can help to resolve this issue. The purpose of the research was to develop the conceptual model for determining the maximum activity of radwaste to be safely disposed in the NSDF and to test it in the case of Lot 3 Vector NSDF (Chornobyl exclusion zone). This paper describes an approach to the development of such a model. The conceptual model of "9"0 Sr migration from Lot 3 through aeration zone and aquifer soils was developed. The results of modelling are shown. The proposals on further steps for the model improvement were developed

The Effect of Moisture Content of Maize Grits on Physicochemical Properties of Its Puffed Food Products Properties of Its Puffed Food Products

Directory of Open Access Journals (Sweden)

S. Sharifi

2016-02-01

Full Text Available In this study the effect of different levels of moisture content of maize grits (10, 13, 16 and 19% as an attribute of physicochemical properties of extruder-derived puffed products, was investigated. The results showed that with increasing maize grits' moisture content, water absorption index (WAI and water solubility index (WSI were decreased. Moreover, with changing in feed moisture content from 10 to 16%, the volume and sectional expansion index (SEI increased but further increase of moisture content to 19% caused a reduction in these parameters. The textural tests also revealed that with increase in moisture content, the compression energy (Nmm, maximum force (N and time to achieve the first major peak (s were increased but the number of peaks was decreased. With increase in the moisture content, specific mechanical energy (SME was decreased, due probably to the reduction in the viscosity of melt. With increase in the moisture content the L and b values were increased but the value of the samples were decreased due to the reduction of Maillard reaction rate. Our data confirms that the moisture content of maize grits may play an important role in the quality of produced extruded snacks and a high quality product can be achieved by optimizing this parameter. In this research, the maximum volume of the extruder product was obtained in 16% of moisture level.

The Effect of Moisture of the Raw Material on the Properties Briquettes for Energy Use

Directory of Open Access Journals (Sweden)

Milan Brožek

2016-01-01

Full Text Available At logging and at the subsequent wood and wood semi-products treatment the fine grained loose waste is arising, e.g. wood dust, saw dust, shavings, chips, bark etc. One of possibilities of its meaningful utilization is the briquetting technology, which product are briquettes determined for energetic utilization (combustion. This report contains the results of tests carried out with the aim to assess the influence of moisture on the briquettes final properties. For the tests the platan tree chips of four moisture levels, namely 5.7 %, 7.7 %, 15.7 % and 23.9 % were used. The basic physical-mechanical properties were the evaluation criteria. Following properties were determined: ash amount, gross calorific value, total moisture content, density, rupture force, length, diameter, weight and mechanical durability. From the results of carried out tests it follows that the best properties were reached at briquettes made from chips of moisture 7.7 %. At higher or lower moisture the briquettes properties were sharply failing (namely rupture force and density.

The effect of moisture absorption on the physical properties of polyurethane shape memory polymer foams

International Nuclear Information System (INIS)

Yu, Ya-Jen; Hearon, Keith; Maitland, Duncan J; Wilson, Thomas S

2011-01-01

The effect of moisture absorption on the glass transition temperature (T g ) and the stress/strain behavior of network polyurethane shape memory polymer (SMP) foams has been investigated. With our ultimate goal of engineering polyurethane SMP foams for use in blood-contacting environments, we have investigated the effects of moisture exposure on the physical properties of polyurethane foams. To the best of our knowledge, this study is the first to investigate the effects of moisture absorption at varying humidity levels (non-immersion and immersion) on the physical properties of polyurethane SMP foams. The SMP foams were exposed to differing humidity levels for varying lengths of time, and they exhibited a maximum water uptake of 8.0% (by mass) after exposure to 100% relative humidity for 96 h. Differential scanning calorimetry results demonstrated that water absorption significantly decreased the T g of the foam, with a maximum water uptake shifting the T g from 67 to 5 °C. Samples that were immersed in water for 96 h and immediately subjected to tensile testing exhibited 100% increases in failure strains and 500% decreases in failure stresses; however, in all cases of time and humidity exposure, the plasticization effect was reversible upon placing moisture-saturated samples in 40% humidity environments for 24 h

FTIR fiber optic methods for the analysis of Hanford Site waste

International Nuclear Information System (INIS)

Rebagay, T.V.; Cash, R.J.; Dodd, D.A.

1995-06-01

Sampling and chemical characterization of mixed high-level waste stored in underground tanks at the Hanford Site is currently in progress. Waste tank safety concerns have provided impetus to analyze this waste. A major safety issue is the possibility of significant concentrations of fuel (ferrocyanide and/or organic compounds) in contact with oxidizers (nitrates and nitrites). It is postulated that under dry conditions and elevated temperatures, ferrocyanide- and/or organic-bearing wastes could undergo rapid exothermic reactions. To maintain the tanks in a safe condition, data are needed on the moisture and fuel concentrations in the waste. Because of the highly radioactive nature of the waste, non-radioactive waste simulants mimicking actual waste are used to provide an initial basis for identifying realistic waste tank safety concerns. Emphasis has been placed on the use of new or existing Fourier transform infrared (FTIR)-based systems with potential for field or tank deployment to perform in situ remote waste characterization. Near-infrared diffuse reflectance and mid-infrared attenuated total reflectance fiber optic probes coupled to a Bio-Rad FTS 60A spectrometry system have been evaluated. The near-infrared diffuse reflectance fiber probe system has also been used for preliminary screening of the moisture content and chemical composition of actual Hanford Site waste tank waste core samples. The attributes of this method for analyzing actual radioactive waste are discussed

Conversion of Food waste to Single Cell Protein using Aspergillus ...

African Journals Online (AJOL)

ADOWIE PERE

2018-03-13

Mar 13, 2018 ... as orange, pineapple, banana, watermelon and cucumber waste as growth ... compared to plant and animal proteins with good ... not affected by weather condition, short generation .... found to be the least source of chemical composition ... Food waste. Proximate composition (%). Moisture. Ash. Crude fibre.

Understanding natural moisturizing mechanisms: implications for moisturizer technology.

Science.gov (United States)

Chandar, Prem; Nole, Greg; Johnson, Anthony W

2009-07-01

Dry skin and moisturization are important topics because they impact the lives of many individuals. For most individuals, dry skin is not a notable concern and can be adequately managed with current moisturizing products. However, dry skin can affect the quality of life of some individuals because of the challenges of either harsh environmental conditions or impaired stratum corneum (SC) dry skin protection processes resulting from various common skin diseases. Dry skin protection processes of the SC, such as the development of natural moisturizing factor (NMF), are complex, carefully balanced, and easily perturbed. We discuss the importance of the filaggrin-NMF system and the composition of NMF in both healthy and dry skin, and also reveal new insights that suggest the properties required for a new generation of moisturizing technologies.

Opto-thermal moisture content and moisture depth profile measurements in organic materials

NARCIS (Netherlands)

Xiao, P.; Guo, X.; Cui, Y.Y.; Imhof, R.; Bicanic, D.D.

2004-01-01

Opto-thermal transient emission radiometry(OTTER) is a infrared remote sensing technique, which has been successfully used in in vivo skin moisture content and skin moisture depth profiling measurements.In present paper, we extend this moisture content measurement capability to analyze the moisture

Role of soil moisture versus recent climate change for the 2010 heat wave in western Russia

Science.gov (United States)

Hauser, Mathias; Orth, René; Seneviratne, Sonia I.

2016-03-01

The severe 2010 heat wave in western Russia was found to be influenced by anthropogenic climate change. Additionally, soil moisture-temperature feedbacks were deemed important for the buildup of the exceptionally high temperatures. We quantify the relative role of both factors by applying the probabilistic event attribution framework and analyze ensemble simulations to distinguish the effect of climate change and the 2010 soil moisture conditions for annual maximum temperatures. The dry 2010 soil moisture alone has increased the risk of a severe heat wave in western Russia sixfold, while climate change from 1960 to 2000 has approximately tripled it. The combined effect of climate change and 2010 soil moisture yields a 13 times higher heat wave risk. We conclude that internal climate variability causing the dry 2010 soil moisture conditions formed a necessary basis for the extreme heat wave.

Optimization of protection and calibration of the moisture-density gages troxler

International Nuclear Information System (INIS)

RAKOTONDRAVANONA, J.E.

2011-01-01

The purpose of this work is the implementation of the principle of optimization of the protection and calibration of moisture-density gages TROXLER. The main objectives are the application of radiation protection and the feasibility of a calibration laboratory design. The calibration of density and moisture may confirm the calibration of moisture-density gages TROXLER. The calibration of density consists of the assembly of measurements on three calibration blocks (magnesium, aluminium and magnesium/aluminium) built in the TRACKER. The value of density uncertainty is ±32 Kg.m -3 . The calibration of moisture is carried out on two calibration blocks (magnesium and magnesium/polyethylene)The value of moisture uncertainty is ±16 Kg.m -3 . The design of the laboratory returns to the dose limitation. The laboratory is designed mainly wall out of ordinary concrete, a good attenuator of the gamma radiations and neutron. For the design, the value of term source gamma is 25.77±0.20μSv.h -1 and the value of term source neutron is 7.88±0.35μSv.h -1 are used for the thickness of the walls. The importance of the design makes it possible to attenuate to the maximum doses and rates dose until the total absorption of the radiations. [fr

Evaluation of Assimilated SMOS Soil Moisture Data for US Cropland Soil Moisture Monitoring

Science.gov (United States)

Yang, Zhengwei; Sherstha, Ranjay; Crow, Wade; Bolten, John; Mladenova, Iva; Yu, Genong; Di, Liping

2016-01-01

Remotely sensed soil moisture data can provide timely, objective and quantitative crop soil moisture information with broad geospatial coverage and sufficiently high resolution observations collected throughout the growing season. This paper evaluates the feasibility of using the assimilated ESA Soil Moisture Ocean Salinity (SMOS)Mission L-band passive microwave data for operational US cropland soil surface moisture monitoring. The assimilated SMOS soil moisture data are first categorized to match with the United States Department of Agriculture (USDA)National Agricultural Statistics Service (NASS) survey based weekly soil moisture observation data, which are ordinal. The categorized assimilated SMOS soil moisture data are compared with NASSs survey-based weekly soil moisture data for consistency and robustness using visual assessment and rank correlation. Preliminary results indicate that the assimilated SMOS soil moisture data highly co-vary with NASS field observations across a large geographic area. Therefore, SMOS data have great potential for US operational cropland soil moisture monitoring.

Contribution to the study of maximum levels for liquid radioactive waste disposal into continental and sea water. Treatment of some typical samples

International Nuclear Information System (INIS)

Bittel, R.; Mancel, J.

1968-10-01

The most important carriers of radioactive contamination of man are the whole of foodstuffs and not only ingested water or inhaled air. That is the reason why, in accordance with the spirit of the recent recommendations of the ICRP, it is proposed to substitute the idea of maximum levels of contamination of water to the MPC. In the case of aquatic food chains (aquatic organisms and irrigated foodstuffs), the knowledge of the ingested quantities and of the concentration factors food/water permit to determinate these maximum levels, or to find out a linear relation between the maximum levels in the case of two primary carriers of contamination (continental and sea waters). The notion of critical food-consumption, critical radioelements and formula of waste disposal are considered in the same way, taking care to attach the greatest possible importance to local situations. (authors) [fr

Municipal Solid Waste Characterization according to Different Income Levels: A Case Study

Directory of Open Access Journals (Sweden)

Huseyin Kurtulus Ozcan

2016-10-01

Full Text Available Solid waste generation and characterization are some of the most important parameters which affect environmental sustainability. Municipal solid waste (MSW characterization depends on social structure and income levels. This study aims to determine the variations in waste components within MSW mass by income levels and seasonal conditions following the analysis conducted on the characterization of solid wastes produced in the Kartal district of the province of Istanbul, which is the research area of this study. To this end, 1.9 tons of solid waste samples were collected to represent four different lifestyles (high, medium, and low income levels, and downtown in the winter and summer periods, and characterization was made on these samples. In order to support waste characterization, humidity content and calorific value analyses were also conducted and various suggestions were brought towards waste management in line with the obtained findings. According to the results obtained in the study, organic waste had the highest rate of waste mass by 57.69%. Additionally, significant differences were found in municipal solid waste components (MSWC based on income level. Average moisture content (MC of solid waste samples was 71.1% in moisture analyses. The average of calorific (heating value (HHV was calculated as 2518.5 kcal·kg−1.

Multiscale soil moisture estimates using static and roving cosmic-ray soil moisture sensors

Science.gov (United States)

McJannet, David; Hawdon, Aaron; Baker, Brett; Renzullo, Luigi; Searle, Ross

2017-12-01

Soil moisture plays a critical role in land surface processes and as such there has been a recent increase in the number and resolution of satellite soil moisture observations and the development of land surface process models with ever increasing resolution. Despite these developments, validation and calibration of these products has been limited because of a lack of observations on corresponding scales. A recently developed mobile soil moisture monitoring platform, known as the rover, offers opportunities to overcome this scale issue. This paper describes methods, results and testing of soil moisture estimates produced using rover surveys on a range of scales that are commensurate with model and satellite retrievals. Our investigation involved static cosmic-ray neutron sensors and rover surveys across both broad (36 × 36 km at 9 km resolution) and intensive (10 × 10 km at 1 km resolution) scales in a cropping district in the Mallee region of Victoria, Australia. We describe approaches for converting rover survey neutron counts to soil moisture and discuss the factors controlling soil moisture variability. We use independent gravimetric and modelled soil moisture estimates collected across both space and time to validate rover soil moisture products. Measurements revealed that temporal patterns in soil moisture were preserved through time and regression modelling approaches were utilised to produce time series of property-scale soil moisture which may also have applications in calibration and validation studies or local farm management. Intensive-scale rover surveys produced reliable soil moisture estimates at 1 km resolution while broad-scale surveys produced soil moisture estimates at 9 km resolution. We conclude that the multiscale soil moisture products produced in this study are well suited to future analysis of satellite soil moisture retrievals and finer-scale soil moisture models.

Maximum solid concentrations of coal water slurries predicted by neural network models

Energy Technology Data Exchange (ETDEWEB)

Cheng, Jun; Li, Yanchang; Zhou, Junhu; Liu, Jianzhong; Cen, Kefa

2010-12-15

The nonlinear back-propagation (BP) neural network models were developed to predict the maximum solid concentration of coal water slurry (CWS) which is a substitute for oil fuel, based on physicochemical properties of 37 typical Chinese coals. The Levenberg-Marquardt algorithm was used to train five BP neural network models with different input factors. The data pretreatment method, learning rate and hidden neuron number were optimized by training models. It is found that the Hardgrove grindability index (HGI), moisture and coalification degree of parent coal are 3 indispensable factors for the prediction of CWS maximum solid concentration. Each BP neural network model gives a more accurate prediction result than the traditional polynomial regression equation. The BP neural network model with 3 input factors of HGI, moisture and oxygen/carbon ratio gives the smallest mean absolute error of 0.40%, which is much lower than that of 1.15% given by the traditional polynomial regression equation. (author)

Moisture convergence using satellite-derived wind fields - A severe local storm case study

Science.gov (United States)

Negri, A. J.; Vonder Haar, T. H.

1980-01-01

Five-minute interval 1-km resolution SMS visible channel data were used to derive low-level wind fields by tracking small cumulus clouds on NASA's Atmospheric and Oceanographic Information Processing System. The satellite-derived wind fields were combined with surface mixing ratios to derive horizontal moisture convergence in the prestorm environment of April 24, 1975. Storms began developing in an area extending from southwest Oklahoma to eastern Tennessee 2 h subsequent to the time of the derived fields. The maximum moisture convergence was computed to be 0.0022 g/kg per sec and areas of low-level convergence of moisture were in general indicative of regions of severe storm genesis. The resultant moisture convergence fields derived from two wind sets 20 min apart were spatially consistent and reflected the mesoscale forcing of ensuing storm development. Results are discussed with regard to possible limitations in quantifying the relationship between low-level flow and between low-level flow and satellite-derived cumulus motion in an antecedent storm environment.

Design of experiment (DOE) based screening of factors affecting municipal solid waste (MSW) composting.

Science.gov (United States)

Kazemi, Khoshrooz; Zhang, Baiyu; Lye, Leonard M; Cai, Qinghong; Cao, Tong

2016-12-01

A design of experiment (DOE) based methodology was adopted in this study to investigate the effects of multiple factors and their interactions on the performance of a municipal solid waste (MSW) composting process. The impact of four factors, carbon/nitrogen ratio (C/N), moisture content (MC), type of bulking agent (BA) and aeration rate (AR) on the maturity, stability and toxicity of compost product was investigated. The statistically significant factors were identified using final C/N, germination index (GI) and especially the enzyme activities as responses. Experimental results validated the use of enzyme activities as proper indices during the course of composting. Maximum enzyme activities occurred during the active phase of decomposition. MC has a significant effect on dehydrogenase activity (DGH), β-glucosidase activity (BGH), phosphodiesterase activity (PDE) and the final moisture content of the compost. C/N is statistically significant for final C/N, DGH, BGH, and GI. The results provided guidance to optimize a MSW composting system that will lead to increased decomposition rate and the production of more stable and mature compost. Copyright © 2016 Elsevier Ltd. All rights reserved.

Determination of Intrinsic Permeability for Packed Waste of Indonesian Solid Waste

Directory of Open Access Journals (Sweden)

Benno Rahardyan

2010-11-01

Full Text Available Gas permeability and intrinsic permeability are the major parameters to promote aeration for packed waste. The objectives of this research are to identify physical parameters of gas transfer from a various type of packed wastes and examine ventilation design theory for landfill to enhance waste stabilization. Method to determine value of gas permeability and intrinsic permeability for packed waste is by flushing the packed column containing various type and physical characteristics of wastes with an air pump. Permeability was calculated by measuring pressure gradient on sampling points of the column using inclined manometer at distance 10 cm, 23 cm, 46 cm, 69 cm, 92 cm and 115 cm from origin. Gas permeability is specifically relied on physical parameters of wastes as follows, density, moisture content, particle size and gas velocity on the surface of compacted waste layer. Compost has finer pore structure and smaller pore size than leaves as well as mixed organic (65% and inorganic wastes (35%. The experiment found the intrinsic permeability of leaves waste are in the order of 10-11 to 10-8 m2, 10-11 to 10-9 m2 for compost and 10-9 m2 for mixed organic (65% and inorganic wastes (35%.

Effective moisture diffusivity and activation energy of rambutan seed under different drying methods to promote storage stability

Science.gov (United States)

Ahmad, So'bah; Shamsul Anuar, Mohd; Saleena Taip, Farah; Shamsudin, Rosnah; M, Siti Roha A.

2017-05-01

The effects of two drying methods, oven and microwave drying on the effective moisture diffusivity and activation energy of rambutan seed were studied. Effective moisture diffusivity and activation energy are the main indicators used for moisture movement within the material. Hence, it is beneficial to determine an appropriate drying method to attain a final moisture content of rambutan seed that potentially could be used as secondary sources in the industry. An appropriate final moisture content will provide better storage stability that can extend the lifespan of the rambutan seed. The rambutan seeds were dried with two drying methods (oven and microwave) at two level of the process variables (oven temperature; 40°C and 60°C and microwave power; 250W and 1000W) at constant initial moisture contents. The result showed that a higher value of effective moisture diffusivity and less activation energy were observed in microwave drying compared to oven drying. This finding portrays microwave drying expedites the moisture removal to achieve the required final moisture content and the most appropriate drying method for longer storage stability for rambutan seed. With respect to the process variables; higher oven temperatures and lower microwave powers also exhibit similar trends. Hopefully, this study would provide a baseline data to determine an appropriate drying method for longer storage period for turning waste to by-products.

Final waste classification and waste form technical position papers

International Nuclear Information System (INIS)

1983-05-01

The waste classification technical position paper describes overall procedures acceptable to NRC staff which may be used by licensees to determine the presence and concentrations of the radionuclides listed in section 61.55, and thereby classifying waste for near-surface disposal. This technical position paper also provides guidance on the types of information which should be included in shipment manifests accompanying waste shipments to near-surface disposal facilities. The technical position paper on waste form provides guidance to waste generators on test methods and results acceptable to NRC staff for implementing the 10 CFR Part 61 waste form requirements. It can be used as an acceptable approach for demonstrating compliance with the 10 CFR Part 61 waste structural stability criteria. This technical position paper includes guidance on processing waste into an acceptable stable form, designing acceptable high-integrity containers, packaging cartridge filters, and minimizing radiation effects on organic ion-exchange resins. The guidance in the waste form technical position paper may be used by licensees as the basis for qualifying process control programs to meet the waste form stability requirements, including tests which can be used to demonstrate resistance to degradation arising from the effects of compression, moisture, microbial activity, radiation, and chemical changes. Generic test data (e.g., topical reports prepared by vendors who market solidification technology) may be used for process control program qualification where such generic data is applicable to the particular types of waste generated by a licensee

Waste Load Allocation Based on Total Maximum Daily Load Approach Using the Charged System Search (CSS Algorithm

Directory of Open Access Journals (Sweden)

Elham Faraji

2016-03-01

Full Text Available In this research, the capability of a charged system search algorithm (CSS in handling water management optimization problems is investigated. First, two complex mathematical problems are solved by CSS and the results are compared with those obtained from other metaheuristic algorithms. In the last step, the optimization model developed by the CSS algorithm is applied to the waste load allocation in rivers based on the total maximum daily load (TMDL concept. The results are presented in Tables and Figures for easy comparison. The study indicates the superiority of the CSS algorithm in terms of its speed and performance over the other metaheuristic algorithms while its precision in water management optimization problems is verified.

Role of soil moisture vs. recent climate change for heat waves in western Russia

Science.gov (United States)

Hauser, Mathias; Orth, Rene; Seneviratne, Sonia

2015-04-01

Using the framework of event attribution, anthropogenic climate change was found to have a discernible influence on the occurence-probability of heat waves, such as the one in Russia in 2010. Soil moisture, on the other hand, is an important physical driver for heat waves as its availability has a large influence on the partitioning of the available surface net radiation into latent and sensible heat flux. The presented study investigates the relative importance of both controls, soil moisture and increasing greenhouse gas concentrations, on heat waves in the region of the 2010 Russian heat wave. This is done with a large number of ensemble members from climate simulations with and without interactive soil moisture for both, the 2000s and the 1960s. The simualtions allow to determine the occurence-probability of heat waves with and without the soil moisture-temperature feedback and to compare it to the change caused by climate change. Thereby, we expect to see the largest effect on daytime maximum temperatures (TXx) and a smaller influence of soil moisture on the mean temperatures and cold extremes.

Validation of soil moisture ocean salinity (SMOS) satellite soil moisture products

Science.gov (United States)

The surface soil moisture state controls the partitioning of precipitation into infiltration and runoff. High-resolution observations of soil moisture will lead to improved flood forecasts, especially for intermediate to large watersheds where most flood damage occurs. Soil moisture is also key in d...

Design of a small scale boiler package for testing high moisture content biofuels

Energy Technology Data Exchange (ETDEWEB)

Proctor, Andrew

2005-07-01

This report presents the results of a project to design a prototype, small-scale boiler (0.88 MWth output) to enable clean and efficient combustion of high moisture content (>30%) biomass fuels. The boiler was based on an open bottom smoke tube design, modified to incorporate water tubes in the combustion chamber running from front to back. These were added to support refractory bricks to create an extra pass in the boiler combustion chamber such that the reflected heat from the refractory increased the rate of evaporation of moisture from the fuel. A chain grate stoker was employed. The combustion tests involved three biofuels: wood pellets with a low moisture content (8-10%) (to provide combustion rates for a commercially proven biofuel); wood chips from forestry waste with a 30-40% moisture content; and spent mushroom compost with 70-75% moisture. The tests on the wood chips required a number of modifications to the fuel feeding system and to the boiler in order to achieve limited success and the tests with the mushroom compost were unsuccessful due to the combination of the high moisture content and the fuel's low calorific value. Experience gained with the wood chips suggested a number of improvements for a future boiler design. As well as describing the experimental work and test results, the report offers an economic analysis (capital costs, fuel costs, running costs) of the scheme.

Amylase production by solid-state fermentation of agro-industrial wastes using Bacillus sp.

Directory of Open Access Journals (Sweden)

Rajshree Saxena

2011-12-01

Full Text Available Solid state fermentation was carried out using various agro- industrial wastes with the best amylase producing strain isolated from soil. Different physicochemical conditions were varied for maximum enzyme production. The strain produced about 5400 units/g of amylase at 1:3 moisture content, 20% inoculum, after 72 h of incubation with Mustard Oil seed cake as the substrate. The optimum temperature and pH of the enzyme activity were found to be 50ºC and 6 respectively. The enzyme was found to be thermostable at 70ºC for about 2 h without any salt. It showed stability at pH range 5-7. The metal ions as Na+, Ca++, Mg++ and Co++ enhanced the enzyme activity.

Hydrous mineral dehydration around heat-generating nuclear waste in bedded salt formations.

Science.gov (United States)

Jordan, Amy B; Boukhalfa, Hakim; Caporuscio, Florie A; Robinson, Bruce A; Stauffer, Philip H

2015-06-02

Heat-generating nuclear waste disposal in bedded salt during the first two years after waste emplacement is explored using numerical simulations tied to experiments of hydrous mineral dehydration. Heating impure salt samples to temperatures of 265 °C can release over 20% by mass of hydrous minerals as water. Three steps in a series of dehydration reactions are measured (65, 110, and 265 °C), and water loss associated with each step is averaged from experimental data into a water source model. Simulations using this dehydration model are used to predict temperature, moisture, and porosity after heating by 750-W waste canisters, assuming hydrous mineral mass fractions from 0 to 10%. The formation of a three-phase heat pipe (with counter-circulation of vapor and brine) occurs as water vapor is driven away from the heat source, condenses, and flows back toward the heat source, leading to changes in porosity, permeability, temperature, saturation, and thermal conductivity of the backfill salt surrounding the waste canisters. Heat pipe formation depends on temperature, moisture availability, and mobility. In certain cases, dehydration of hydrous minerals provides sufficient extra moisture to push the system into a sustained heat pipe, where simulations neglecting this process do not.

MoisturEC: a new R program for moisture content estimation from electrical conductivity data

Science.gov (United States)

Terry, Neil; Day-Lewis, Frederick D.; Werkema, Dale D.; Lane, John W.

2018-01-01

Noninvasive geophysical estimation of soil moisture has potential to improve understanding of flow in the unsaturated zone for problems involving agricultural management, aquifer recharge, and optimization of landfill design and operations. In principle, several geophysical techniques (e.g., electrical resistivity, electromagnetic induction, and nuclear magnetic resonance) offer insight into soil moisture, but data‐analysis tools are needed to “translate” geophysical results into estimates of soil moisture, consistent with (1) the uncertainty of this translation and (2) direct measurements of moisture. Although geostatistical frameworks exist for this purpose, straightforward and user‐friendly tools are required to fully capitalize on the potential of geophysical information for soil‐moisture estimation. Here, we present MoisturEC, a simple R program with a graphical user interface to convert measurements or images of electrical conductivity (EC) to soil moisture. Input includes EC values, point moisture estimates, and definition of either Archie parameters (based on experimental or literature values) or empirical data of moisture vs. EC. The program produces two‐ and three‐dimensional images of moisture based on available EC and direct measurements of moisture, interpolating between measurement locations using a Tikhonov regularization approach.

Concept for waste package environment tests in the Yucca Mountain exploratory shaft

International Nuclear Information System (INIS)

Yow, J.L. Jr.

1985-05-01

The Nevada Nuclear Waste Storage Investigations (NNWSI) project is studying a tuffaceous rock unit located at Yucca Mountain on the western boundary of the Nevada Test Site, Nye County, Nevada. The objective is to evaluate the suitability of the volcanic rocks located above the water table at Yucca Mountain as a potential location for a repository for high level radioactive waste. As part of the NNWSI project, Lawrence Livermore National Laboratory is responsible for the design of the waste package and for determining the expected performance of the waste package in the repository environment. To design an optimal waste package system for the unsaturated emplacement environment, the mechanisms by which liquid water can return to contact the metal canister after peaking of the thermal load must be established. Definition of these flux and flow mechanisms is essential for estimating canister corrosion modes and rates. Therefore, three waste package environment tests are being designed for the in situ phase of exploratory shaft testing. These tests emphasize measurement techniques that offer the possibility of characterizing the movement of water into and through the pores and fractures of the densely welded Topopah Spring Member. Other measurement techniques will be used to examine the interactions between moisture migration and the thermomechanical rock mass behavior. Three reduced-scale heater tests will use electrical resistive heaters in a horizontal configuration. All three tests are designed to investigate moisture conditions in the rock during heating and cooling phases of a thermal cycle so that the effects of these moisture conditions on the performance of the waste package system may be established. 28 refs., 4 figs., 3 tabs

Modeling studies of gas movement and moisture migration at Yucca Mountain, Nevada

Energy Technology Data Exchange (ETDEWEB)

Tsang, Y.W.; Pruess, K. [Lawrence Berkeley Lab., CA (United States)

1991-06-01

Modeling studies on moisture redistribution processes that are mediated by gas phase flow and diffusion have been carried out. The problem addressed is the effect of a lowered humidity of the soil gas at the land surface on moisture removal from Yucca Mountain, the potential site for a high-level nuclear waste repository. At the land surface, humid formation gas contacts much drier atmospheric air. Near this contact, the humidity of the soil gas may be considerably lower than at greater depth, where the authors expect equilibrium with the liquid phase and close to 100% humidity. The lower relative humidity of the soil gas may be modeled by imposing, at the land surface, an additional negative capillary suction corresponding to vapor pressure lowering according to Kelvin`s Equation, thus providing a driving force for the upward movement of moisture in both the vapor and liquid phases. Sensitivity studies show that moisture removal from Yucca Mountain arising from the lowered-relative-humidity boundary condition is controlled by vapor diffusion. There is much experimental evidence in the soil literature that diffusion of vapor is enhanced due to pore-level phase change effects by a few orders of magnitude. Modeling results presented here will account for this enhancement in vapor diffusion.

On-line moisture analysis

International Nuclear Information System (INIS)

Cutmore, N.G.; Mijak, D.G

2002-01-01

Measurement of the moisture content of iron ore has become a key issue for controlling moisture additions for dust suppression. In most cases moisture content is still determined by manual or automatic sampling of the ore stream, followed by conventional laboratory analysis by oven drying. Although this procedure enables the moisture content to be routinely monitored, it is too slow for control purposes. This has generated renewed interest in on-line techniques for the accurate and rapid measurement of moisture in iron ore on conveyors. Microwave transmission techniques have emerged over the past 40 years as the dominant technology for on-line measurement of moisture in bulk materials, including iron ores. Alternative technologies have their limitations. Infra-red analysers are used in a variety of process industries, but rely on the measurement of absorption by moisture in a very thin surface layer. Consequently such probes may be compromised by particle size effects and biased presentation of the bulk material. Nuclear-based analysers measure the total hydrogen content in the sample and do not differentiate between free and combined moisture. Such analysers may also be sensitive to material presentation and elemental composition. Very low frequency electromagnetic probes, such as capacitance or conductance probes, operate in the frequency region where the DC conductivity dominates much of the response, which is a function not only of moisture content but also of ionic composition and chemistry. These problems are overcome using microwave transmission techniques, which also have the following advantages, as a true bulk moisture analysis is obtained, because a high percentage of the bulk material is analysed; the moisture estimate is mostly insensitive to any biased presentation of moisture, for example due to stratification of bulk material with different moisture content and because no physical contact is made between the sensor and the bulk material. This is

MoisturEC: A New R Program for Moisture Content Estimation from Electrical Conductivity Data.

Science.gov (United States)

Terry, Neil; Day-Lewis, Frederick D; Werkema, Dale; Lane, John W

2018-03-06

Noninvasive geophysical estimation of soil moisture has potential to improve understanding of flow in the unsaturated zone for problems involving agricultural management, aquifer recharge, and optimization of landfill design and operations. In principle, several geophysical techniques (e.g., electrical resistivity, electromagnetic induction, and nuclear magnetic resonance) offer insight into soil moisture, but data-analysis tools are needed to "translate" geophysical results into estimates of soil moisture, consistent with (1) the uncertainty of this translation and (2) direct measurements of moisture. Although geostatistical frameworks exist for this purpose, straightforward and user-friendly tools are required to fully capitalize on the potential of geophysical information for soil-moisture estimation. Here, we present MoisturEC, a simple R program with a graphical user interface to convert measurements or images of electrical conductivity (EC) to soil moisture. Input includes EC values, point moisture estimates, and definition of either Archie parameters (based on experimental or literature values) or empirical data of moisture vs. EC. The program produces two- and three-dimensional images of moisture based on available EC and direct measurements of moisture, interpolating between measurement locations using a Tikhonov regularization approach. Published 2018. This article is a U.S. Government work and is in the public domain in the USA.

Calculation of combustible waste fraction (CWF) estimates used in organics safety issue screening

International Nuclear Information System (INIS)

Heasler, P.G.; Gao, F.; Toth, J.J.

1998-08-01

This report describes how in-tank measurements of moisture (H 2 O) and total organic carbon (TOC) are used to calculate combustible waste fractions (CWF) for 138 of the 149 Hanford single shell tanks. The combustible waste fraction of a tank is defined as that proportion of waste that is capable of burning when exposed to an ignition source. These CWF estimates are used to screen tanks for the organics complexant safety issue. Tanks with a suitably low fraction of combustible waste are classified as safe. The calculations in this report determine the combustible waste fractions in tanks under two different moisture conditions: under current moisture conditions, and after complete dry out. The first fraction is called the wet combustible waste fraction (wet CWF) and the second is called the dry combustible waste fraction (dry CWF). These two fractions are used to screen tanks into three categories: if the wet CWF is too high (above 5%), the tank is categorized as unsafe; if the wet CWF is low but the dry CWF is too high (again, above 5%), the tank is categorized as conditionally safe; finally, if both the wet and dry CWF are low, the tank is categorized as safe. Section 2 describes the data that was required for these calculations. Sections 3 and 4 describe the statistical model and resulting fit for dry combustible waste fractions. Sections 5 and 6 present the statistical model used to estimate wet CWF and the resulting fit. Section 7 describes two tests that were performed on the dry combustible waste fraction ANOVA model to validate it. Finally, Section 8 presents concluding remarks. Two Appendices present results on a tank-by-tank basis

The effect of mixing ratio variation of sludge and organic solid waste on biodrying process

Science.gov (United States)

Nasution, A. C.; Kristanto, G. A.

2018-01-01

In this study, organic waste was co-biodried with sludge cake to determine which mixing ratio gave the best result. The organic waste was consisted of dried leaves and green leaves, while the sludge cake was obtained from a waste water treatment plant in Bekasi. The experiment was performed on 3 lab-scale reactors with same specifications. After 21 days of experiment, it was found that the reactor with the lowest mixing fraction of sludge (5:1) has the best temperature profile and highest moisture content depletion compared with others. Initial moisture content and initial volatile solid content of this reactor’s feedstock was 52.25% and 82.4% respectively. The airflow rate was 10 lpm. After biodrying was done, the final moisture content of the feedstock from Reactor C was 22.0% and the final volatile solid content was 75.9%.The final calorific value after biodrying process was 3179,28kcal/kg.

On-line moisture analysis

CERN Document Server

Cutmore, N G

2002-01-01

Measurement of the moisture content of iron ore has become a key issue for controlling moisture additions for dust suppression. In most cases moisture content is still determined by manual or automatic sampling of the ore stream, followed by conventional laboratory analysis by oven drying. Although this procedure enables the moisture content to be routinely monitored, it is too slow for control purposes. This has generated renewed interest in on-line techniques for the accurate and rapid measurement of moisture in iron ore on conveyors. Microwave transmission techniques have emerged over the past 40 years as the dominant technology for on-line measurement of moisture in bulk materials, including iron ores. Alternative technologies have their limitations. Infra-red analysers are used in a variety of process industries, but rely on the measurement of absorption by moisture in a very thin surface layer. Consequently such probes may be compromised by particle size effects and biased presentation of the bulk mater...

Potential of Briquetting as a Waste-Management Option for Handling Market-Generated Vegetable Waste in Port Harcourt, Nigeria

Directory of Open Access Journals (Sweden)

Olugbemiro M. Akande

2018-03-01

Full Text Available The conversion of biomass to high-density briquettes is a potential solution to solid waste problems as well as to a high dependence on fuel wood in developing countries. In this study, the potential of converting vegetable waste to briquettes using waste paper as a binder was investigated. A sample size of 30 respondents was interviewed using a self-administered questionnaire at the D-line fruit and vegetable market in Port Harcourt, Nigeria. Carrot and cabbage leaves were selected for briquetting based on their availability and heating value. This waste was sun-dried, pulverized, torrefied and fermented. Briquettes were produced with a manual briquette press after the processed vegetable waste was mixed with waste paper in four paper:waste ratios, i.e., 10:90, 15:85, 20:80 and 25:75. The moisture content, densities and cooking efficiency of the briquettes were determined using the oven-drying method, the water-displacement method, and the water-boiling test, respectively. There was no observed trend in moisture content values of the briquettes, which varied significantly between 3.0% and 8.5%. There was no significant variation in the densities, which ranged from 0.79 g/cm3 to 0.96 g/cm3 for all the briquette types. A degree of compaction above 300% was achieved for all the briquette types. Water-boiling test results revealed that 10:90 paper:sun-dried cabbage briquettes had the highest ignitability of 0.32 min. Torrefied carrot briquettes with 25% paper had the least boiling time and the highest burning rates of 9.21 min and 4.89 g/min, respectively. It was concluded that cabbage and carrot waste can best be converted into good-quality briquettes after torrefaction.

Effect of waste synthetic bag pieces on the CBR value of expansive Soil

Directory of Open Access Journals (Sweden)

Ajay Kumar Agarwal

2015-03-01

Full Text Available Expansive soils such as black cotton soil which are widely distributed in India have a tendency for volume changes due to change in moisture content. Also exhibits very low bearing capacity and high compressibility. Stabilization of such soil by admixture is used commonly now days. But no mix is suitable to improve all the types of soil. But it is obvious that depending on type of soil & type of admixture the optimum mix can be designed.  In this paper a mix has been designed to improve the bearing capacity of soil by using fly ash and lime mixture, reinforced with waste synthetic bag pieces. Various tests are carried out to determine the CBR value and other soil properties with and without using any admixture and reinforcement. The maximum value of CBR was found to be23.82% for 2.5 mm penetration and 22.21% for 5 mm penetration, when waste synthetic bag pieces of size 2 cm * 2 cm were used at a proportion of 0.1%.

Characteristics of medical waste in Malaysia

International Nuclear Information System (INIS)

Anwar Johari; Mutahharah, M.M.; Abdul, A.; Kalantarifard, A.; Rozainee, M.

2010-01-01

The main purpose for the waste characterization is to provide the data necessary to design a new extension of the existing medical waste incinerator plant in Perak. Medical waste from the existing medical waste incinerator was categorized into several components through a sorting process. Proximate analysis was conducted to determine its moisture content, volatile matter contents, ash and fixed carbon contents. Ultimate analysis was also conducted for the determination of carbon, hydrogen, oxygen, nitrogen and sulphur contents. The characterization study was conducted on site and for duration of 7 days. Result showed that the average total plastics (rigid and film) was 38 wt%. The rest of the composition comprised of mixed paper, surgery dress, diapers, absorbents and gloves with weight percents of 10%, 3%, 18%, 18% and 13% respectively. The average moisture content of the individual waste was 19.3%, 3%, 61.4%, 30.7%, 13.8% and 53.5 % for mixed paper, plastics, diaper, surgery dress, glove and absorbent respectively. The average volatile matter was 71.3%, 87.5%, 32.2%, 65.1%, 65.1%, 78.5% and 41.0% for individual waste. The average ash content was 2.1%, 0.7%, 2.6%, 0.5%, 6.5% and 0.8% for mixed paper, plastics, diaper, surgery dress, glove and absorbent respectively. The average fixed carbon was determined at 7.3%, 8.8%, 3.8%, 3.7%, 1.2% and 4.7% for mixed paper, plastics, diaper, surgery dress, glove and absorbent respectively. The average carbon, hydrogen, oxygen, nitrogen and sulphur contents are 51.8%, 8.6%, 35.5%, 0.3% and less than 0.1 respectively. The average calorific value (dry basis) was 27 MJ/ kg. (author)

The waste-to-energy framework for integrated multi-waste utilization: Waste cooking oil, waste lubricating oil, and waste plastics

Energy Technology Data Exchange (ETDEWEB)

Singhabhandhu, Ampaitepin; Tezuka, Tetsuo [Energy Economics Laboratory, Department of Socio-Environmental Energy Science, Graduate School of Energy Science, Kyoto University, Yoshida-honmachi, Sakyo-ku, Kyoto 606-8501 (Japan)

2010-06-15

Energy generation by wastes is considered one method of waste management that has the benefit of energy recovery. From the waste-to-energy point of view, waste cooking oil, waste lubricating oil, and waste plastics have been considered good candidates for feedstocks for energy conversion due to their high heating values. Compared to the independent management of these three wastes, the idea of co-processing them in integration is expected to gain more benefit. The economies of scale and the synergy of co-processing these wastes results in higher quality and higher yield of the end products. In this study, we use cost-benefit analysis to evaluate the integrated management scenario of collecting the three wastes and converting them to energy. We report the total heat of combustion of pyrolytic oil at the maximum and minimum conversion rates, and conduct a sensitivity analysis in which the parameters of an increase of the electricity cost for operating the process and increase of the feedstock transportation cost are tested. We evaluate the effects of economy of scale in the case of integrated waste management. We compare four cases of waste-to-energy conversion with the business as usual (BAU) scenario, and our results show that the integrated co-processing of waste cooking oil, waste lubricating oil, and waste plastics is the most profitable from the viewpoints of energy yield and economics. (author)

Inactivation of Salmonella Senftenberg strain W 775 during composting of biowastes and garden wastes.

Science.gov (United States)

Ceustermans, A; De Clercq, D; Aertsen, A; Michiels, C; Geeraerd, A; Van Impe, J; Coosemans, J; Ryckeboer, J

2007-07-01

Determination of the minimum requirements (time-temperature relationship and moisture content) that are needed for a sufficient eradication of an indicator organism. To determine the hygienic safety of composting processes, the indicator organism Salmonella enterica ssp. enterica serotype Senftenberg strain W 775 (further abbreviated as W 775) was artificially inoculated on a meat carrier and monitored subsequently. Different types of composting processes, e.g. composting in enclosed facilities, in open-air and in-vessel composting, were investigated. The waste feedstocks used in this work were either biowastes (i.e. vegetable, fruit and garden wastes; also called source-separated household wastes) or pure garden wastes. Beside these large-scale trials, we also conducted some lab experiments in order to determine the impact of temperature, moisture content and the presence of an indigenous microflora on the eradication of W 775. We found the temperature to be the most important parameter to eradicate W 775 from compost. When the temperature of the compost heap is 60 degrees C and the moisture content varies between 60-65%, W 775 (10(8) CFU g(-1)) will be inactivated within 10 h of composting. The moisture content is, beside temperature, a second parameter that influences the survival of W 775. When the water content of the composting materials or meat carriers is reduced, a higher survival rate of W 775 was observed (survival rate increases 0.5 log(10) unit when there is a reduction of 5% in moisture content). In addition, other parameters (such as microbial antagonism, toxic compounds, etc.) have an influence on the survival of W 775 as well. Our study demonstrates that all types of composting processes tested in this work were sufficient to eradicate W 775 providing that they are well managed in terms of temperature and moisture content. To give a better view on the parameters of importance for the eradication of W 775 during composting.

Mathematical modeling in low-level radioactive waste management

International Nuclear Information System (INIS)

Ward, D.S.; Yeh, G.T.

1978-01-01

Mathematical modeling of moisture transport through near-surface infiltration reduction seals above low-level waste trenches may be used to aid in the evaluation of engineering design alternatives. The infiltration of rainwater must be reduced for successful radionuclide containment within a typical shallow trench. Clay admixtures offer not only long-term integrity, but the necessary durability. The use of models is exemplified in the calculation of spatial moisture content and velocity distributions in the vicinity of a near-surface seal

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics

International Nuclear Information System (INIS)

Gug, JeongIn; Cacciola, David; Sobkowicz, Margaret J.

2015-01-01

Highlights: • Briquetting was used to produce solid fuels from municipal solid waste and recycled plastics. • Optimal drying, processing temperature and pressure were found to produce stable briquettes. • Addition of waste plastics yielded heating values comparable with typical coal feedstocks. • This processing method improves utilization of paper and plastic diverted from landfills. - Abstract: Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics

Energy Technology Data Exchange (ETDEWEB)

Gug, JeongIn, E-mail: Jeongin_gug@student.uml.edu; Cacciola, David, E-mail: david_cacciola@student.uml.edu; Sobkowicz, Margaret J., E-mail: Margaret_sobkowiczkline@uml.edu

2015-01-15

Highlights: • Briquetting was used to produce solid fuels from municipal solid waste and recycled plastics. • Optimal drying, processing temperature and pressure were found to produce stable briquettes. • Addition of waste plastics yielded heating values comparable with typical coal feedstocks. • This processing method improves utilization of paper and plastic diverted from landfills. - Abstract: Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in

WASTES: a waste management logistics/economics model

International Nuclear Information System (INIS)

McNair, G.W.; Shay, M.R.; Fletcher, J.F.; Cashwell, J.W.

1985-01-01

The WASTES logistics model is a simulation language based model for analyzing the logistic flow of spent fuel/nuclear waste throughout the waste management system. The model tracks the movement of spent fuel/nuclear waste from point of generation to final destination. The model maintains inventories of spent fuel/nuclear waste at individual reactor sites as well as at various facilities within the waste management system. A maximum of 14 facilities may be utilized within a single run. These 14 facilities may include any combination of the following facilities: (1) federal interim storage (FIS), (2) reprocessing (REP), (3) monitored retrievable storage (MRS), (4) geological disposal facilities (GDF). The movement of spent fuel/nuclear waste between these facilities is controlled by the user specification of loading and unloading rates, annual and maximum capacities and commodity characteristics (minimum age or heat constraints) for each individual facility. In addition, the user may specify varying levels of priority on the spent fuel/nuclear waste that will be eligible for movement within a given year. These levels of priority allow the user to preferentially move spent fuel from reactor sites that are experiencing a loss of full-core-reserve (FCR) margin in a given year or from reactors that may be in the final stages of decommissioning. The WASTES model utilizes the reactor specific data available from the PNL spent fuel database. This database provides reactor specific information on items such as spent fuel basin size, reactor location, and transportation cask preference (i.e., rail or truck cask). In addition, detailed discharge data is maintained that provides the number of assemblies, metric tons, and exposure for both historic and projected discharges at each reactor site

Moisture transport in coated wood

NARCIS (Netherlands)

Meel, P.A. van; Erich, S.J.F.; Huinink, H.P.; Kopinga, K.; Jong, J. DE; Adan, O.C.G.

2011-01-01

Moisture accumulation inside wood causes favorable conditions for decay. Application of a coating alters the moisture sorption of wood and prevents accumulation of moisture. This paper presents the results of a nuclear magnetic resonance (NMR) study on the influence of a coating on the moisture

Soil microbial community responses to antibiotic-contaminated manure under different soil moisture regimes.

Science.gov (United States)

Reichel, Rüdiger; Radl, Viviane; Rosendahl, Ingrid; Albert, Andreas; Amelung, Wulf; Schloter, Michael; Thiele-Bruhn, Sören

2014-01-01

Sulfadiazine (SDZ) is an antibiotic frequently administered to livestock, and it alters microbial communities when entering soils with animal manure, but understanding the interactions of these effects to the prevailing climatic regime has eluded researchers. A climatic factor that strongly controls microbial activity is soil moisture. Here, we hypothesized that the effects of SDZ on soil microbial communities will be modulated depending on the soil moisture conditions. To test this hypothesis, we performed a 49-day fully controlled climate chamber pot experiments with soil grown with Dactylis glomerata (L.). Manure-amended pots without or with SDZ contamination were incubated under a dynamic moisture regime (DMR) with repeated drying and rewetting changes of >20 % maximum water holding capacity (WHCmax) in comparison to a control moisture regime (CMR) at an average soil moisture of 38 % WHCmax. We then monitored changes in SDZ concentration as well as in the phenotypic phospholipid fatty acid and genotypic 16S rRNA gene fragment patterns of the microbial community after 7, 20, 27, 34, and 49 days of incubation. The results showed that strongly changing water supply made SDZ accessible to mild extraction in the short term. As a result, and despite rather small SDZ effects on community structures, the PLFA-derived microbial biomass was suppressed in the SDZ-contaminated DMR soils relative to the CMR ones, indicating that dynamic moisture changes accelerate the susceptibility of the soil microbial community to antibiotics.

MoisturEC: an R application for geostatistical estimation of moisture content from electrical conductivity data

Science.gov (United States)

Terry, N.; Day-Lewis, F. D.; Werkema, D. D.; Lane, J. W., Jr.

2017-12-01

Soil moisture is a critical parameter for agriculture, water supply, and management of landfills. Whereas direct data (as from TDR or soil moisture probes) provide localized point scale information, it is often more desirable to produce 2D and/or 3D estimates of soil moisture from noninvasive measurements. To this end, geophysical methods for indirectly assessing soil moisture have great potential, yet are limited in terms of quantitative interpretation due to uncertainty in petrophysical transformations and inherent limitations in resolution. Simple tools to produce soil moisture estimates from geophysical data are lacking. We present a new standalone program, MoisturEC, for estimating moisture content distributions from electrical conductivity data. The program uses an indicator kriging method within a geostatistical framework to incorporate hard data (as from moisture probes) and soft data (as from electrical resistivity imaging or electromagnetic induction) to produce estimates of moisture content and uncertainty. The program features data visualization and output options as well as a module for calibrating electrical conductivity with moisture content to improve estimates. The user-friendly program is written in R - a widely used, cross-platform, open source programming language that lends itself to further development and customization. We demonstrate use of the program with a numerical experiment as well as a controlled field irrigation experiment. Results produced from the combined geostatistical framework of MoisturEC show improved estimates of moisture content compared to those generated from individual datasets. This application provides a convenient and efficient means for integrating various data types and has broad utility to soil moisture monitoring in landfills, agriculture, and other problems.

Evaluation of rice and cassava processing wastes for suitability as ...

African Journals Online (AJOL)

OGBO

plants, good moisture absorption capacity and amenability to processing and ... wastes as animal feed (cassava peel) and fuel (rice husk) have been .... Saccharomyces cerevisae and Lactobacillus sp. solid media fermentation techniques.

Assessment of multiple geophysical techniques for the characterization of municipal waste deposit sites

Science.gov (United States)

Gaël, Dumont; Tanguy, Robert; Nicolas, Marck; Frédéric, Nguyen

2017-10-01

In this study, we tested the ability of geophysical methods to characterize a large technical landfill installed in a former sand quarry. The geophysical surveys specifically aimed at delimitating the deposit site horizontal extension, at estimating its thickness and at characterizing the waste material composition (the moisture content in the present case). The site delimitation was conducted with electromagnetic (in-phase and out-of-phase) and magnetic (vertical gradient and total field) methods that clearly showed the transition between the waste deposit and the host formation. Regarding waste deposit thickness evaluation, electrical resistivity tomography appeared inefficient on this particularly thick deposit site. Thus, we propose a combination of horizontal to vertical noise spectral ratio (HVNSR) and multichannel analysis of the surface waves (MASW), which successfully determined the approximate waste deposit thickness in our test landfill. However, ERT appeared to be an appropriate tool to characterize the moisture content of the waste, which is of prior information for the organic waste biodegradation process. The global multi-scale and multi-method geophysical survey offers precious information for site rehabilitation studies, water content mitigation processes for enhanced biodegradation or landfill mining operation planning.

Determination of renewable energy yield from mixed waste material from the use of novel image analysis methods.

Science.gov (United States)

Wagland, S T; Dudley, R; Naftaly, M; Longhurst, P J

2013-11-01

Two novel techniques are presented in this study which together aim to provide a system able to determine the renewable energy potential of mixed waste materials. An image analysis tool was applied to two waste samples prepared using known quantities of source-segregated recyclable materials. The technique was used to determine the composition of the wastes, where through the use of waste component properties the biogenic content of the samples was calculated. The percentage renewable energy determined by image analysis for each sample was accurate to within 5% of the actual values calculated. Microwave-based multiple-point imaging (AutoHarvest) was used to demonstrate the ability of such a technique to determine the moisture content of mixed samples. This proof-of-concept experiment was shown to produce moisture measurement accurate to within 10%. Overall, the image analysis tool was able to determine the renewable energy potential of the mixed samples, and the AutoHarvest should enable the net calorific value calculations through the provision of moisture content measurements. The proposed system is suitable for combustion facilities, and enables the operator to understand the renewable energy potential of the waste prior to combustion. Copyright © 2013 Elsevier Ltd. All rights reserved.

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics.

Science.gov (United States)

Gug, JeongIn; Cacciola, David; Sobkowicz, Margaret J

2015-01-01

Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in higher heating value. Analysis of the post-processing water uptake and compressive strength showed a correlation between density and stability to both mechanical stress and humid environment. Proximate analysis indicated heating values comparable to coal. The results showed that mechanical and moisture uptake stability were improved when the moisture and air contents were optimized. Moreover, the briquette

Effect of boundary conditions on thermohydraulic behavior of clay buffer used in nuclear waste repository

International Nuclear Information System (INIS)

Arul Peter, A.; Murugesan, K.; Mamidi, Ganesh; Sharma, Umesh Kumar; Sharma, D. Akanshu; Arora, Puneet

2010-01-01

The use of nuclear energy is increasing dramatically in the world due to the fast depletion of fossil fuels, and hence the nuclear waste disposal and its short and long-term effects are of considerable importance. One of the options considered for nuclear waste disposal is underground nuclear waste repository facility. In this underground nuclear waste disposal system the waste filled canisters are placed in the rock surrounded by an engineered clay barrier and the whole system is buried in the geological formation, which serves as the natural or geological barrier. The important characteristic of the clay barrier is that it should not open up for radiation though it is continuously subjected to heat loading from the canisters. The heat and moisture transport mechanisms through the clay barrier plays an important role in deciding its mechanical strength. Clay behaves as an unsaturated porous material when it is used as a buffer material in nuclear waste facility. The governing equations for heat and moisture transfer through unsaturated porous media are coupled and nonlinear and hence they have to be solved using numerical solution technique. This paper reports the results of a numerical study on heat and moisture transport through a buffer layer made of clay as used in nuclear waste repository. Galerkin's weighted residual finite element method has been employed for the solution of the non-linear coupled governing equations used to represent the heat and moisture transport through unsaturated clay material. A detailed computational procedure has been established for the solution of the non-linear governing equations using Newton-Raphson technique. Initially the code has been validated with available experimental results. Then numerical simulation results were obtained for heat and moisture variations within the buffer material for Dirichlet temperature boundary conditions in the range, 50 deg C 2 2 , with an aim to simulate the boundary conditions which the clay

An Overview of Organic Waste in Composting

Directory of Open Access Journals (Sweden)

Kadir Aeslina Abdul

2016-01-01

Full Text Available This paper reviewed studies on the composting process of organic waste. Organic wastes are wastes that easily biodegradable. These wastes are produced from many sources such as agricultural waste, market waste, kitchen waste, urban solid food wastes and municipal solid waste. Without proper management, these waste could create several environment problem. Therefore, composting is the best low cost alternative solution to overcome this problem. Composting method can degrade all types of organic wastes like fruits, vegetables, plants, yard wastes and others. The composition from organic waste that could be used as nutrients for crops, soil additive and for environmental management. However, many factors can contribute to the quality of the compost products as different types of organic wastes have different concentrations of nutrients, nitrogen, phosphorous and potassium (N, P, K which are the common macro nutrients present in fertilizers. The presences of heavy metals show how composts can be applied to soils without contributing any ill effect. In term of the factor affecting the composting process, temperature, pH, moisture contents and carbon nitrogen ratio (C:N are the main parameters that contribute to the efficiency of the composting process.

Moisture Transport in Wood

DEFF Research Database (Denmark)

Astrup, Thomas; Hansen, Kurt Kielsgaard; Hoffmeyer, Preben

2005-01-01

Modelling of moisture transport in wood is of great importance as most mechanical and physical properties of wood depend on moisture content. Moisture transport in porous materials is often described by Ficks second law, but several observations indicate that this does not apply very well to wood....... Recently at the Technical University of Denmark, Department of Civil Engineering, a new model for moisture transport in wood has been developed. The model divides the transport into two phases, namely water vapour in the cell lumens and bound water in the cell walls....

Influence of use of quartzite waste in moisture expansion of masses for ceramic tiles; Influencia do uso de residuo de quartzito na expansao por umidade de massas de revestimentos ceramicos planos

Energy Technology Data Exchange (ETDEWEB)

Medeiros, R.R.; Goncalves, W. P.; Cartaxo, J.M.; Ferreira, H.S.; Neves, G.A.; Ferreira, H.C., E-mail: rosinaldo.medeiros@ufrr.br, E-mail: wherllyson@yahoo.com.br, E-mail: julianamelo25@gmail.com, E-mail: hebersivini@gmail.com, E-mail: gelmires.neves@ufcg.edu.br, E-mail: heber.carlos@ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Programa de Pos-Graduacao em Ciencia e Engenharia de Materiais

2017-04-15

The moisture expansion (ME) is characterized as an increase in physical dimensions of ceramic body when in contact with water (liquid or vapor). The ME phenomenon may contribute to the appearance of serious pathology in ceramic tiles such as cracks, detachment or more severe damages. This work aimed to study the problem of ME in ceramic masses added with quartzite waste for use in tiles using the dilatometry and three-point flexural strength methods. The raw materials were processed and characterized by laser diffraction particle size analysis, plasticity, chemical analysis, thermogravimetric and differential thermal analysis, and X-ray diffraction. The results showed that the addition of quartzite waste generally elevated ME values for bodies fired at temperatures below 1100 °C. For bodies fired at 1200 °C the results indicated high mechanical performance and ME decrease, and the best results for additive formulations was 15% of quartzite. (author)

Moisture in Crawl Spaces

Science.gov (United States)

Anton TenWolde; Samuel V. Glass

2013-01-01

Crawl space foundations can be designed and built to avoid moisture problems. In this article we provide a brief overview of crawl spaces with emphasis on the physics of moisture. We review trends that have been observed in the research literature and summarize cur-rent recommendations for moisture control in crawl spaces.

Evaluation of the performance of solidified commercial low-level wastes in an arid climate

International Nuclear Information System (INIS)

Graham, M.J.; Walter, M.B.

1984-01-01

Shallow land burial is being used as a disposal method for commercial low-level waste at waste disposal sites in arid (Hanford, Washington) and humid (Barnwell, South Carolina) climatic regions. A field lysimeter facility has been established at Hanford in which to conduct waste-form leaching tests. The primary objective of this research is to determine typical source terms generated by commercial solidified low-level wastes. The field lysimeter facility consists of 10, 3 M deep by 1.8 M diameter, closed-bottomed lysimeters around a central 4 M deep by 4 M diameter instrument caisson. Commercial cement and dow polymer waste samples were removed from 210 L drums and placed in the 1.8 M diameter lysimeters. Two bitumen samples are planned to be emplaced in the facility this year. The central caisson provides access to the instrumentation in the individual lysimeters and allows selective sampling of the soil and waste forms. Suction candles (ceramic cups) placed around the waste will be used to periodically collect soil water samples for chemical analysis. Meteorological data, moisture content, and soil temperature are being automatically monitored at the facility. Characterization of the soils and waste forms have been partially completed. These data consist of moisture release characteristics, particle size distribution, concentrations and distributions of radionuclides in the waste streams, and concentrations of hydrophilic organic species in one of the waste streams

Radiation transport in high-level waste form

International Nuclear Information System (INIS)

Arakali, V.S.; Barnes, S.M.

1992-01-01

The waste form selected for vitrifying high-level nuclear waste stored in underground tanks at West Valley, NY is borosilicate glass. The maximum radiation level at the surface of a canister filled with the high-level waste form is prescribed by repository design criteria for handling and disposition of the vitrified waste. This paper presents an evaluation of the radiation transport characteristics for the vitreous waste form expected to be produced at West Valley and the resulting neutron and gamma dose rates. The maximum gamma and neutron dose rates are estimated to be less than 7500 R/h and 10 mRem/h respectively at the surface of a West Valley canister filled with borosilicate waste glass

An ecological engineering approach for keeping water from reaching interred wastes in arid or semiarid regions

International Nuclear Information System (INIS)

Anderson, J.E.

1997-01-01

This paper describes application of a soil-plant cover system (SPCS) to preclude water from reaching interred wastes in arid and semiarid regions. Where potential evapotranspiration far exceeds precipitation, water can be kept from reaching buried wastes by (1) providing a sufficiently deep cap of soil to store precipitation that falls while plants are dormant and (2) maintaining plant cover to deplete soil moisture during the growing season, thereby emptying the storage reservoir. Research at the Idaho National Engineering Laboratory (INEL) has shown that 2 m of soil is adequate to store moisture from snowmelt and spring rains. Healthy stands of perennial grasses and shrubs adapted to the INEL climate use all available soil moisture, even during a very wet growing season. However, burrowing by small mammals or ants may affect the performance of a SPCS by increasing infiltration of water. Intrusion barriers of gravel and cobble can be used to restrict burrowing, but emplacement of such barriers affects soil moisture storage and plant rooting depths. A replicated field experiment to investigate the implications of those effects is in progress. Incorporation of an SPCS should be considered in the design of isolation barriers for shallow land burial of hazardous wastes in and regions

Study of time variation of terrestrial gamma radiation due to depth distribution of soil moisture content

International Nuclear Information System (INIS)

Yoshioka, Katsuhiro

1994-01-01

An empirical equation was deduced from studies of time variations of terrestrial gamma exposure rate and soil moisture content with depth distribution in the surface layer. It was definitely suggested that the variation of terrestrial gamma exposure rate is most strongly influenced by the change of soil moisture content at 5 cm depth. The seasonal variation with a relative maximum in early autumn and a relative minimum in early spring was clearly obtained in the consequence of long time measurements of terrestrial gamma exposure rate and degree of soil dryness. The diurnal change and phase difference due to the effect of depth were also obtained in the dynamic characteristics of soil moisture content at 3 different depths. From the comparison between measured terrestrial gamma exposure rate and that evaluated from soil moisture content using the empirical equation, it was seen that seasonal variations of the both agreed fairly well as a whole. (author)

Landscape complexity and soil moisture variation in south Georgia, USA, for remote sensing applications

Science.gov (United States)

Giraldo, Mario A.; Bosch, David; Madden, Marguerite; Usery, Lynn; Kvien, Craig

2008-08-01

SummaryThis research addressed the temporal and spatial variation of soil moisture (SM) in a heterogeneous landscape. The research objective was to investigate soil moisture variation in eight homogeneous 30 by 30 m plots, similar to the pixel size of a Landsat Thematic Mapper (TM) or Enhanced Thematic Mapper plus (ETM+) image. The plots were adjacent to eight stations of an in situ soil moisture network operated by the United States Department of Agriculture-Agriculture Research Service USDA-ARS in Tifton, GA. We also studied five adjacent agricultural fields to examine the effect of different landuses/land covers (LULC) (grass, orchard, peanuts, cotton and bare soil) on the temporal and spatial variation of soil moisture. Soil moisture field data were collected on eight occasions throughout 2005 and January 2006 to establish comparisons within and among eight homogeneous plots. Consistently throughout time, analysis of variance (ANOVA) showed high variation in the soil moisture behavior among the plots and high homogeneity in the soil moisture behavior within them. A precipitation analysis for the eight sampling dates throughout the year 2005 showed similar rainfall conditions for the eight study plots. Therefore, soil moisture variation among locations was explained by in situ local conditions. Temporal stability geostatistical analysis showed that soil moisture has high temporal stability within the small plots and that a single point reading can be used to monitor soil moisture status for the plot within a maximum 3% volume/volume (v/v) soil moisture variation. Similarly, t-statistic analysis showed that soil moisture status in the upper soil layer changes within 24 h. We found statistical differences in the soil moisture between the different LULC in the agricultural fields as well as statistical differences between these fields and the adjacent 30 by 30 m plots. From this analysis, it was demonstrated that spatial proximity is not enough to produce similar

Evaluating soil moisture and hydraulic conductivity in semi-arid rangeland soils

International Nuclear Information System (INIS)

Whitaker, M.P.L.

1993-01-01

The US DOE's Office of Civilian Radioactive Waste Management (DOE-OCRWM) Fellowship Program supports various disciplines of academic research related to the isolation of radionuclides from the biosphere. The purpose of this paper is to provide an example of a university research application in the specific discipline of hydrology and water resources (a multi-disciplinary field encompassing engineering and the earth sciences), and to discuss how this research pertains to the objectives of the DOE-OCRWM Fellowship Program. The university research application is twofold: One portion focuses on the spatial variability of soil moisture (θ) and the other section compares point measurements with small watershed estimates of hydraulic conductivity (K) in a semi-arid rangeland soil in Arizona. For soil moisture measurements collected over a range of horizontal sampling intervals, no spatial correlation was evident. This outcome is reassuring to computer modelers who have assumed no spatial correlation for soil moisture over smaller scales. In regard to hydraulic conductivity, point measurements differed significantly from small watershed estimates of hydraulic conductivity which were derived from a calibrated and verified rainfall-runoff computer model. The estimates of saturated hydraulic conductivity (Ks) were obtained from previous computer simulations in which measured data was collected in the same research location as the present study

Buffer moisture protection system

International Nuclear Information System (INIS)

Ritola, J.; Peura, J.

2013-11-01

With the present knowledge, bentonite blocks have to be protected from the air relative humidity and from any moisture leakages in the environment that might cause swelling of the bentonite blocks during the 'open' installation phase before backfilling. The purpose of this work was to design the structural reference solution both for the bottom of the deposition hole and for the buffer moisture protection and dewatering system with their integrated equipment needed in the deposition hole. This report describes the Posiva's reference solution for the buffer moisture protection system and the bottom plate on basis of the demands and functional requirements set by long-term safety. The reference solution with structural details has been developed in research work made 2010-2011. The structural solution of the moisture protection system has not yet been tested in practice. On the bottom of the deposition hole a copper plate which protects the lowest bentonite block from the gathered water is installed straight to machined and even rock surface. The moisture protection sheet made of EPDM rubber is attached to the copper plate with an inflatable seal. The upper part of the moisture protection sheet is fixed to the collar structures of the lid which protects the deposition hole in the disposal tunnel. The main function of the moisture protection sheet is to protect bentonite blocks from the leaking water and from the influence of the air humidity at their installation stage. The leaking water is controlled by the dewatering and alarm system which has been integrated into the moisture protection liner. (orig.)

Role of Soil Moisture vs. Recent Climate Change for the 2010 Heat Wave in Western Russia

Science.gov (United States)

Hauser, Mathias; Orth, René; Seneviratne, Sonia

2016-04-01

Extreme event attribution statements are often conditional on increased greenhouse gas concentrations or a particular ocean state, but not on other physical factors of the climate system. Here we extend the classical framework and assess the influence of soil moisture on a heat wave to obtain a physical attribution statement. In particular, we test the role of soil-moisture-temperature feedbacks which have been shown to be generally relevant for the build-up of exceptionally high temperatures. As a case study we investigate the severe 2010 heat wave in western Russia, which was previously found to be influenced by anthropogenic climate change. We quantify the relative role of climate change and that of soil moisture-temperature feedbacks with the event attribution framework and analyze ensemble simulations to distinguish the effect of climate change and the 2010 soil moisture conditions for annual maximum temperatures. We find that climate change from 1960 to 2000 alone has approximately tripled the risk of a severe heat wave in western Russia. The combined effect of climate change and the dry 2010 soil moisture yields a 13 times higher heat wave risk. We conclude that internal climate variability causing the dry 2010 soil moisture conditions formed the basis for this extreme heatwave.

Effects of moisture migration on shrinkage, pore pressure and other concrete properties

International Nuclear Information System (INIS)

Chapman, D.A.; England, G.L.

1977-01-01

This work investigates the uniaxial migration of moisture in long, upright, limestone concrete cylinders, sealed at the base and sides, and open at the top. The design represents a section through a concrete pressure vessel wall. The cylinders are subjected to a sustained temperature difference between their ends, with maximum temperatures between 105 0 C and 200 0 C. Readings of pore pressure, water content and temperature are taken at various positions along the axis of the cylinders. In one cylinder transverse and longitudinal shrinkage readings are also recorded. The results for the cylinders show that moisture migration is away from the hot face of the specimens, causing reduction in both pore pressure and water content values in this region. The moisture migration creates a drying front which moves slowly up the specimens. Evaporation drying takes place from the unsealed end of the specimen. A drying front moves into the concrete and considerable weight loss is recorded as moisture escapes to the atmosphere. The rate of movement of the drying front is slower than that of the hot front and is proportional to the temperature difference between the top of the specimen and the surrounding atmosphere. In the shrinkage specimen, values of transverse and longitudinal shrinkage reflect the water content results. The specimen indicates that shrinkage occurs in a concrete pressure vessel, in the regions where moisture is lost. The restraint of the mass of concrete surrounding these regions sets up a three dimensional state of internal tensile stress. The areas into which the moisture migrates tend to swell, creating an internal stress situation, which is this

Microcomputerized neutron moisture gauge

International Nuclear Information System (INIS)

Liu Shengkang; Mei Yu

1987-01-01

A microcomputerized neutron moisture gauge is introduced. This gauge consists of a neutron moisture sensor and instruments. It is developed from the neutron moisture gauge for concrete mixer. A TECH-81 single card microcomputer is used for count, computation and display. It has the function of computing compensated quantity of sand. It can acquire the data from several neutron sensors by the multichanneling sampling, therefore it can measure moisture values of sand in several hoppers simultaneously. The precision of the static state calibration curve is 0.24% wt. The error limits of the dynamic state check is < 0.50% wt

Glucoamylase production from food waste by solid state fermentation and its evaluation in the hydrolysis of domestic food waste

Directory of Open Access Journals (Sweden)

Esra Uçkun Kiran

2014-08-01

Full Text Available In this study, food wastes such as waste bread, savory, waste cakes, cafeteria waste, fruits, vegetables and potatoes were used as sole substrate for glucoamylase production by solid state fermentation. Response surface methodology was employed to optimize the fermentation conditions for improving the production of high activity enzyme. It was found that waste cake was the best substrate for glucoamylase production. Among all the parameters studied, glucoamylase activity was significantly affected by the initial pH and incubation time. The highest glucoamylase activity of 108.47 U/gds was achieved at initial pH of 7.9, moisture content of 69.6% wt., inoculum loading of 5.2×105 cells/gram substrate (gs and incubation time of 6 d. The enzyme preparation could effectively digest 50% suspension of domestic food waste in 24 h with an almost complete saccharification using an enzyme dose of only 2U/g food waste at 60°C.

Town of Hague landfill reclamation study: Research ways to increase waste heating value and reduce waste volume. Final report

Energy Technology Data Exchange (ETDEWEB)

Salerni, E. [SSB Environmental Inc., Albany, NY (United States)

1997-01-01

Monitored composing was studied as a method for reducing the quantity of waste requiring disposed from a landfill reclamation project. After each of two re-screening steps, composted {open_quotes}soil{close_quotes} from a single long windrow of varying depths and moisture content was subjected to analytical testing to determine its suitability to remain as backfill in a reclaimed landfill site. The remaining uncomposted waste was combusted at a waste-to-energy facility to determine if Btu values were improved. Results indicate that a full-scale composting operation could result in a net decrease of approximately 11 percent in disposal costs. The Btu value of the reclaimed waste was calculated to be 4,500 to 5,000 Btu/lb. The feasibility of composting reclaimed waste at other landfill reclamation projects will depend upon site-specific technical and economic factors, including size and nature of the organic fraction of the waste mass, local processing costs, and the cost of waste disposal alternatives.

Effect of Initial Moisture on the Adsorption and Desorption Equilibrium Moisture Contents of Polished Rice

OpenAIRE

Murata, Satoshi; Amaratunga, K.S.P.; Tanaka, Fumihiko; Hori, Yoshiaki; 村田, 敏; 田中, 史彦; 堀, 善昭

1993-01-01

The moisture adsorption and desorption properties for polished rice have been measured using a dynamic ventilatory method. Air temperatures of 10,20,30 and 40℃, relative humidities of 50,60,70,80 and 90%, and five levels of initial moisture contents ranging approximately from 8% to 19% d.b. were used to obtain moisture content data. The value of equilibrium moisture content for each initial moisture content at the range of air condition was determined by a method of nonlinear least squares. R...

Moisture content measurement in paddy

Science.gov (United States)

Klomklao, P.; Kuntinugunetanon, S.; Wongkokua, W.

2017-09-01

Moisture content is an important quantity for agriculture product, especially in paddy. In principle, the moisture content can be measured by a gravimetric method which is a direct method. However, the gravimetric method is time-consuming. There are indirect methods such as resistance and capacitance methods. In this work, we developed an indirect method based on a 555 integrated circuit timer. The moisture content sensor was capacitive parallel plates using the dielectric constant property of the moisture. The instrument generated the output frequency that depended on the capacitance of the sensor. We fitted a linear relation between periods and moisture contents. The measurement results have a standard uncertainty of 1.23 % of the moisture content in the range of 14 % to 20 %.

Effect of pH, temperature and moisture content during composting of rice straw burning at different temperature with food waste and effective microorganisms

Science.gov (United States)

Azura Zakarya, Irnis; Baya Khalib, Siti Noor; Ramzi, Norhasykin Mohd

2018-03-01

Rice straw is considered as one of the most important agricultural residues and represented as one of the major by-products from rice production process. Normally, rice straw that produced after harvesting season been directly burned on-farm. Conversion of rice straw into value added compost will improve the productivity of plant, reduction of pollution towards environment and reduction of local pollution due to open burning activity. The objective of this study was to evaluate the performance of composting rice straw ash (RSA) with food waste (FW) and effective microorganisms (EM) in term of the compost quality (pH, temperature, moisture content). RSA was prepared by burning the raw rice straw at three different temperature of 300°C, 400°C and 500°C for one hour. EM used during the composting process was prepared by mixing of brown sugar, `tempe' and water that can be used after one week of fermentation process. There are four treatments of RSA-compost; RSA (300°C), RSA (400°C), RSA (500°C) and control (raw rice straw) with the same amount of compost medium; 1kg black soil, 0.5kg RSA, 3L EM and 1kg FW. The composting process happens for 30 days. During the composting process, all the parameters of RSA-compost obtained in a range like; pH value 8-10, temperature 20-50°C and moisture content 40-60%. The result showed that all compost quality of rice straw ash compost obtained in an acceptable range for final compost to establish.

Data Assimilation using observed streamflow and remotely-sensed soil moisture for improving sub-seasonal-to-seasonal forecasting

Science.gov (United States)

Arumugam, S.; Mazrooei, A.; Lakshmi, V.; Wood, A.

2017-12-01

Subseasonal-to-seasonal (S2S) forecasts of soil moisture and streamflow provides critical information for water and agricultural systems to support short-term planning and mangement. This study evaluates the role of observed streamflow and remotely-sensed soil moisture from SMAP (Soil Moisture Active Passive) mission in improving S2S streamflow and soil moisture forecasting using data assimilation (DA). We first show the ability to forecast soil moisture at monthly-to-seaasonal time scale by forcing climate forecasts with NASA's Land Information System and then compares the developed soil moisture forecast with the SMAP data over the Southeast US. Our analyses show significant skill in forecasting real-time soil moisture over 1-3 months using climate information. We also show that the developed soil moisture forecasts capture the observed severe drought conditions (2007-2008) over the Southeast US. Following that, we consider both SMAP data and observed streamflow for improving S2S streamflow and soil moisture forecasts for a pilot study area, Tar River basin, in NC. Towards this, we consider variational assimilation (VAR) of gauge-measured daily streamflow data in improving initial hydrologic conditions of Variable Infiltration Capacity (VIC) model. The utility of data assimilation is then assessed in improving S2S forecasts of streamflow and soil moisture through a retrospective analyses. Furthermore, the optimal frequency of data assimilation and optimal analysis window (number of past observations to use) are also assessed in order to achieve the maximum improvement in S2S forecasts of streamflow and soil moisture. Potential utility of updating initial conditions using DA and providing skillful forcings are also discussed.

Mixed low-level waste form evaluation

International Nuclear Information System (INIS)

Pohl, P.I.; Cheng, Wu-Ching; Wheeler, T.; Waters, R.D.

1997-01-01

A scoping level evaluation of polyethylene encapsulation and vitreous waste forms for safe storage of mixed low-level waste was performed. Maximum permissible radionuclide concentrations were estimated for 15 indicator radionuclides disposed of at the Hanford and Savannah River sites with respect to protection of the groundwater and inadvertent intruder pathways. Nominal performance improvements of polyethylene and glass waste forms relative to grout are reported. These improvements in maximum permissible radionuclide concentrations depend strongly on the radionuclide of concern and pathway. Recommendations for future research include improving the current understanding of the performance of polymer waste forms, particularly macroencapsulation. To provide context to these estimates, the concentrations of radionuclides in treated DOE waste should be compared with the results of this study to determine required performance

Radioactive droplet moisture transfer from nuclear power plant spray pool

International Nuclear Information System (INIS)

Elokhin, A.P.

1995-01-01

Problem on transfer of radioactive droplet moisture with an account of its evaporation from the nuclear power plant spray pool (NPP coolant) is considered. Formulae enabling evaluation of droplet and radioactive water admixture lifetime as a whole, as well as the maximum distance (by wind), over which it can extend, are obtained. Recommendations for decrease in the droplet dispersed composition and reduction in scale of radioactive contamination of underlying surface are given. 10 refs.; 3 figs.; 1 tab

The Effects of Soil Type, Particle Size, Temperature, and Moisture on Reproduction of Belonolaimus longicaudatus.

Science.gov (United States)

Robbins, R T; Barker, K R

1974-01-01

Effects of soil type, particle size, temperature, and moisture on the reproduction of Belonolaimus longicaudatus were investigated under greenhouse conditions. Nematode increases occurred only in soils with a minimum of 80% sand and a maximum of 10% clay. Optimum soil particle size for reproduction of the Tarboro, N.C. and Tifton, Ga. populations of the nematode was near that of 120-370 mum (65-mesh) silica sand. Reproduction was greatest at 25-30 C. Some reproduction by the Tifton, Ga. population occurred at 35 C, whereas the Tarboro, N.C. population declined, as compared to the initial inoculum. Both populations reproduced slightly at 20 C. Nematode reproduction was greater at a moisture level of 7% than at a high of 30% or a low of 2%. Reproduction occurred at the high moisture level only when the nutrient solution was aerated.

Atmospheric rivers moisture transport from a Lagrangian perspective

Science.gov (United States)

Ramos, A. M.; Nieto, R.; Tomé, R.; Gimeno, L.; Trigo, R. M.; Liberato, M. L. R.; Lavers, D. A.

2015-12-01

An automated atmospheric rivers (ARs) detection algorithm is used for the North Atlantic Ocean Basin allowing the identification of the major ARs that affected western European coasts between 1979 and 2014 over the winter half-year (October to March). The entire west coast of Europe was divided into five domains, namely, the Iberian Peninsula (9.75° W; 36-43.75° N), France (4.5° W; 43.75-50° N), UK (4.5° W; 50-59° N), southern Scandinavia and the Netherlands (5.25° E; 50-59° N), and northern Scandinavia (5.25° E; 59-70° N). Following the identification of the main ARs that made landfall in western Europe, a Lagrangian analysis was then applied in order to identify the main sources of moisture that reach each domain. The Lagrangian dataset used was obtained from the FLEXPART model global simulation from 1979 to 2012, where the atmosphere was divided into approximately 2.0 million parcels, and it was forced by ERA-Interim reanalysis on a 1° latitude-longitude grid. Results show that, in general, for all regions considered, the major climatological source of moisture extends along the subtropical North Atlantic, from the Florida Peninsula (northward of 20° N), to each sink region, with the nearest coast to each sink region always appearing as a local maximum of evaporation. In addition, during the AR events, the Atlantic subtropical source is reinforced and displaced, with a slight northward movement of the moisture sources is found when the sink region is positioned at higher latitudes. In conclusion, the results confirm the advection of moisture linked to ARs from subtropical ocean areas, but also the existence of a tropical one, and the mid-latitude sources further the analysed longitude along the North Atlantic is located eastward.

Small-Scale Waste-to-Energy Technology for Contingency Bases

Science.gov (United States)

2012-05-24

Maintenance, Operator Skill Level Requires Waste Sorting/Pre-processing Scaling and Capacity Issues Technology Readiness Issues Composting Useful By-Product...combustion temperature possible with this technology. These variables are important for improved tar conversion, increased tolerance for high moisture

Portable neutron moisture gage for the moisture determination of structure parts

International Nuclear Information System (INIS)

Harnisch, M.

1985-01-01

For determining the moisture of structure parts during building or before repairing a portable neutron moisture gage consisting of a neutron probe and pulse analyzer has been developed. The measuring process, calibration, and prerequisites of application are briefly discussed

Future equivalent of 2010 Russian heatwave intensified by weakening soil moisture constraints

Science.gov (United States)

Rasmijn, L. M.; van der Schrier, G.; Bintanja, R.; Barkmeijer, J.; Sterl, A.; Hazeleger, W.

2018-05-01

The 2010 heatwave in eastern Europe and Russia ranks among the hottest events ever recorded in the region1,2. The excessive summer warmth was related to an anomalously widespread and intense quasi-stationary anticyclonic circulation anomaly over western Russia, reinforced by depletion of spring soil moisture1,3-5. At present, high soil moisture levels and strong surface evaporation generally tend to cap maximum summer temperatures6-8, but these constraints may weaken under future warming9,10. Here, we use a data assimilation technique in which future climate model simulations are nudged to realistically represent the persistence and strength of the 2010 blocked atmospheric flow. In the future, synoptically driven extreme warming under favourable large-scale atmospheric conditions will no longer be suppressed by abundant soil moisture, leading to a disproportional intensification of future heatwaves. This implies that future mid-latitude heatwaves analogous to the 2010 event will become even more extreme than previously thought, with temperature extremes increasing by 8.4 °C over western Russia. Thus, the socioeconomic impacts of future heatwaves will probably be amplified beyond current estimates.

Leaching of radioactive waste forms under saturated and unsaturated flow conditions

International Nuclear Information System (INIS)

Petelka, M.F.

1987-01-01

To predict the environmental impact of shallow land burial sites for radioactive waste, the mobilization and migration of waste nuclides must be estimated. The theoretical understanding that in potential leaching mechanisms leach-rate variations may arise from changes in both moisture content and volumetric flow rate was tested in column flow leach experiments using labeled vermiculite particles as a simulated waste form. As far as possible, conditions of flow rate and solution ion concentration were chosen to roughly approximate expected field conditions. A modified pressure-plate apparatus was developed, tested, and found suitable for the production of steady-state unsaturated conditions with leachate flow. Water content was determined using the gamma-ray attenuation method. The effects of several parameters on leaching were studied, including moisture content and pore velocity. Pore velocity effects were found to be negligible. It was found that the leach rate depends on the fraction of the exposed waste surface that is wetted and varies with the mobile water content in a non-linear fashion. The experimental results indicate that the release rate of radionuclides placed within a properly sited low-level waste disposal site may be two to three times smaller than that predicted assuming saturated conditions. This study was performed using a homogeneous fine-grained synthetic waste form, at room temperature, with a near neutral pH leachant and oxidizing conditions

Evaluation of the performance of solidified commercial low-level wastes in an arid climate

International Nuclear Information System (INIS)

Graham, M.J.; Walter, M.B.

1984-09-01

Shallow land burial is being used as a disposal method for commercial low-level waste at waste disposal sites in arid (Hanford site near Richland, Washington) and humid (Barnwell, South Carolina) climatic regions. A field lysimeter facility has been established at the Hanford site in which to conduct waste-form leaching tests. The primary objective of this research is to determine typical source terms generated by commercial solidified low-level wastes. The field lysimeter facility consists of ten 3-m-deep by 1.8-m-diameter, closed-bottom lysimeters around a central instrument caisson, 4 m in diameter. Commercial cement and vinyl ester-styrene waste samples were removed from 210-L drums and placed in the 1.8-m-diameter lysimeters. Two bitumen samples are planned to be emplaced in the facility in 1984. The central caisson provides access to the instrumentation in the individual lysimeters and allows selective sampling of the soil and waste forms. Suction candles (ceramic cups) placed around the waste will be used to periodically collect soil water samples for chemical analysis. Meteorological data, moisture content, and soil temperature are automatically monitored at the facility. Characterization of the soils and waste forms have been partially completed. These data consist of moisture release characteristics, particle size distribution, concentrations and distributions of radionuclides in the waste forms, concentrations of radionuclides in the waste streams, and concentrations of hydrophilic organic species in one of the waste steams. 8 references, 3 figures, 5 tables

Advanced evaporation/concentration treatment technology for radioactive liquid waste

International Nuclear Information System (INIS)

Zhang Zhijian; Lu Zhiming; Yu Ruixia

1997-01-01

A new and effective two stage moisture separator which removes remaining water droplet and free ion in secondary steam can be added between the evaporator and the condenser of existing liquid waste treatment system. Its addition increases decontamination factor to more than ten times. Ion content in condensed water is decreased considerably. Condensed water meets emission standard without passing through ion exchanger. Detail fundamentals are analysed and results are given: (1) system diagram, (2) structure sketch of the two stage moisture separator, (3) laboratory test results

[Spatial heterogeneity of soil moisture of mountain apple orchards with rainwater collection and infiltration (RWCI) system in the Loess Plateau, China].

Science.gov (United States)

Song, Xiao Lin; Zhao, Xi Ning; Gao, Xiao Dong; Wu, Pu Te; Ma, Wen; Yao, Jie; Jiang, Xiao Li; Zhang, Wei

2017-11-01

Water scarcity is a critical factor influencing rain-fed agricultural production on the Loess Plateau, and the exploitation of rainwater is an effective avenue to alleviate water scarcity in this area. This study was conducted to investigate the spatial and temporal distribution of soil moisture in the 0-300 cm under a 21-year-old apple orchard with the rainwater collection and infiltration (RWCI) system by using a time domain reflectometer (TDR) probe on the Loess Plateau. The results showed that there was a low soil moisture zone in the 40-80 cm under the CK, and the RWCI system significantly increased soil moisture in this depth interval. Over this depth, the annual average soil moisture under RWCI 40 , RWCI 60 and RWCI 80 was 39.2%, 47.2% and 29.1% higher than that of bare slope (BS) and 75.3%, 85.4% and 62.7% higher than that of CK, respectively. The maximum infiltration depth of water under RWCI 40 , RWCI 60 and RWCI 80 was 80 cm, 120 cm and 180 cm, respectively, and the soil moisture in the 0-60, 0-100 and 0-120 cm was more affected by RWCI 40 , RWCI 60 and RWCI 80 , respectively. Over the whole growth period of apple tree, the maximum value of soil moisture content in the 0-300 cm existed in the RWCI 80 treatment, followed by the RWCI 40 and RWCI 60 treatments. Overall, the RWCI system is an effective meaning of transforming rainwater to available water resources and realizing efficient use of agricultural water on the Loess Plateau.

Drying wood waste with a pulse combustion dryer

Energy Technology Data Exchange (ETDEWEB)

Buchkowski, A.G. [Spectrum Engineering Corp., Ltd., Peterborough, Ontario (Canada); Kitchen, J.A. [John A. Kitchen, Ltd., Hastings, Ontario (Canada)

1993-12-31

There is a vast amount of wood waste available to be used as an alternate fuel if its moisture could be reduced efficiently. Tests have been conducted to assess an industrial dryer using pulse combustion as a heating source for drying wood waste; specifically sawdust and pulverized wet hog fuel. Pulse combustion offers the advantage of high heat transfer, efficient combustion, and low NO{sub x} emissions. The material is injected into the exhaust gases in the tailpipe of the combustor which uses natural gas or propane as a fuel. The turbulence created by the pulsations enhance the drying process by reducing the boundary layer thicknesses. The materials is further dried in a rotary drum. The material has been dried without scorching or burning in tests where the inlet moisture content has been as high as 60% on a wet basis. The outlet moisture contents achieved have typically been 10%. Analysis of the test data and cost estimates of the equipment indicate that the pulse combustion drying system is at least comparable to existing systems in terms of operating costs, and offers very significant savings in capital costs. Testing with various other materials such as wood pulp, sludges and peat is continuing to further assess the equipment`s performance.

Seasonality in ENSO-related precipitation, river discharges, soil moisture, and vegetation index in Colombia

Science.gov (United States)

Poveda, GermáN.; Jaramillo, Alvaro; Gil, Marta MaríA.; Quiceno, Natalia; Mantilla, Ricardo I.

2001-08-01

An analysis of hydrologic variability in Colombia shows different seasonal effects associated with El Niño/Southern Oscillation (ENSO) phenomenon. Spectral and cross-correlation analyses are developed between climatic indices of the tropical Pacific Ocean and the annual cycle of Colombia's hydrology: precipitation, river flows, soil moisture, and the Normalized Difference Vegetation Index (NDVI). Our findings indicate stronger anomalies during December-February and weaker during March-May. The effects of ENSO are stronger for streamflow than for precipitation, owing to concomitant effects on soil moisture and evapotranspiration. We studied time variability of 10-day average volumetric soil moisture, collected at the tropical Andes of central Colombia at depths of 20 and 40 cm, in coffee growing areas characterized by shading vegetation ("shaded coffee"), forest, and sunlit coffee. The annual and interannual variability of soil moisture are highly intertwined for the period 1997-1999, during strong El Niño and La Niña events. Soil moisture exhibited greater negative anomalies during 1997-1998 El Niño, being strongest during the two dry seasons that normally occur in central Colombia. Soil moisture deficits were more drastic at zones covered by sunlit coffee than at those covered by forest and shaded coffee. Soil moisture responds to wetter than normal precipitation conditions during La Niña 1998-1999, reaching maximum levels throughout that period. The probability density function of soil moisture records is highly skewed and exhibits different kinds of multimodality depending upon land cover type. NDVI exhibits strong negative anomalies throughout the year during El Niños, in particular during September-November (year 0) and June-August (year 0). The strong negative relation between NDVI and El Niño has enormous implications for carbon, water, and energy budgets over the region, including the tropical Andes and Amazon River basin.

Forest litter crickets prefer higher substrate moisture for oviposition: Evidence from field and lab experiments.

Science.gov (United States)

de Farias-Martins, Fernando; Sperber, Carlos Frankl; Albeny-Simões, Daniel; Breaux, Jennifer Ann; Fianco, Marcos; Szinwelski, Neucir

2017-01-01

For insects, choosing a favorable oviposition site is a type of parental care, as far as it increases the fitness of its offspring. Niche theory predicts that crickets should show a bell-shaped oviposition response to substrate moisture. However, lab experiments with mole crickets showed a linear oviposition response to substrate moisture. Studies with the house cricket Acheta domesticus also showed a linear juvenile body growth response to water availability, thus adult ovipositing females should respond positively to substrate moisture. We used a field experiment to evaluate the relationship between oviposition preference and substrate moisture in forest litter-dwelling cricket species. We also evaluated oviposition responses to substrate moisture level in Ubiquepuella telytokous, the most abundant litter cricket species in our study area, using a laboratory study. We offered cotton substrate for oviposition which varied in substrate moisture level from zero (i.e., dry) to maximum water absorption capacity. We used two complementary metrics to evaluate oviposition preference: (i) presence or absence of eggs in each sampling unit as binary response variable, and (ii) number of eggs oviposited per sampling unit as count response variable. To test for non-linear responses, we adjusted generalized additive models (GAMM) with mixed effects. We found that both cricket oviposition probability and effort (i.e., number of eggs laid) increased linearly with substrate moisture in the field experiment, and for U. telytokous in the lab experiment. We discarded any non-linear responses. Our results demonstrate the importance of substrate moisture as an ecological niche dimension for litter crickets. This work bolsters knowledge of litter cricket life history association with moisture, and suggests that litter crickets may be particularly threatened by changes in climate that favor habitat drying.

Evaluation of Optimum Moisture Content for Composting of Beef Manure and Bedding Material Mixtures Using Oxygen Uptake Measurement

Directory of Open Access Journals (Sweden)

Eunjong Kim

2016-05-01

Full Text Available Moisture content influences physiological characteristics of microbes and physical structure of solid matrices during composting of animal manure. If moisture content is maintained at a proper level, aerobic microorganisms show more active oxygen consumption during composting due to increased microbial activity. In this study, optimum moisture levels for composting of two bedding materials (sawdust, rice hull and two different mixtures of bedding and beef manure (BS, Beef cattle manure+sawdust; BR, Beef cattle manure+rice hull were determined based on oxygen uptake rate measured by a pressure sensor method. A broad range of oxygen uptake rates (0.3 to 33.3 mg O2/g VS d were monitored as a function of moisture level and composting feedstock type. The maximum oxygen consumption of each material was observed near the saturated condition, which ranged from 75% to 98% of water holding capacity. The optimum moisture content of BS and BR were 70% and 57% on a wet basis, respectively. Although BS’s optimum moisture content was near saturated state, its free air space kept a favorable level (above 30% for aerobic composting due to the sawdust’s coarse particle size and bulking effect.

Evaluation of Optimum Moisture Content for Composting of Beef Manure and Bedding Material Mixtures Using Oxygen Uptake Measurement.

Science.gov (United States)

Kim, Eunjong; Lee, Dong-Hyun; Won, Seunggun; Ahn, Heekwon

2016-05-01

Moisture content influences physiological characteristics of microbes and physical structure of solid matrices during composting of animal manure. If moisture content is maintained at a proper level, aerobic microorganisms show more active oxygen consumption during composting due to increased microbial activity. In this study, optimum moisture levels for composting of two bedding materials (sawdust, rice hull) and two different mixtures of bedding and beef manure (BS, Beef cattle manure+sawdust; BR, Beef cattle manure+rice hull) were determined based on oxygen uptake rate measured by a pressure sensor method. A broad range of oxygen uptake rates (0.3 to 33.3 mg O2/g VS d) were monitored as a function of moisture level and composting feedstock type. The maximum oxygen consumption of each material was observed near the saturated condition, which ranged from 75% to 98% of water holding capacity. The optimum moisture content of BS and BR were 70% and 57% on a wet basis, respectively. Although BS's optimum moisture content was near saturated state, its free air space kept a favorable level (above 30%) for aerobic composting due to the sawdust's coarse particle size and bulking effect.

Evaluation of the moisture sources in two extreme landfalling atmospheric river events using an Eulerian WRF tracers tool

Science.gov (United States)

Eiras-Barca, Jorge; Dominguez, Francina; Hu, Huancui; Garaboa-Paz, Daniel; Miguez-Macho, Gonzalo

2017-12-01

A new 3-D tracer tool is coupled to the WRF model to analyze the origin of the moisture in two extreme atmospheric river (AR) events: the so-called Great Coastal Gale of 2007 in the Pacific Ocean and the Great Storm of 1987 in the North Atlantic. Results show that between 80 and 90 % of moisture advected by the ARs, and a high percentage of the total precipitation produced by the systems have a tropical origin. The tropical contribution to precipitation is in general above 50 % and largely exceeds this value in the most affected areas. Local convergence transport is responsible for the remaining moisture and precipitation. The ratio of tropical moisture to total moisture is maximized as the cold front arrives on land. Vertical cross sections of the moisture content suggest that the maximum in tropical humidity does not necessarily coincide with the low-level jet (LLJ) of the extratropical cyclone. Instead, the amount of tropical humidity is maximized in the lowest atmospheric level in southern latitudes and can be located above, below or ahead of the LLJ in northern latitudes in both analyzed cases.

Evaluation of the moisture sources in two extreme landfalling atmospheric river events using an Eulerian WRF tracers tool

Directory of Open Access Journals (Sweden)

J. Eiras-Barca

2017-12-01

Full Text Available A new 3-D tracer tool is coupled to the WRF model to analyze the origin of the moisture in two extreme atmospheric river (AR events: the so-called Great Coastal Gale of 2007 in the Pacific Ocean and the Great Storm of 1987 in the North Atlantic. Results show that between 80 and 90 % of moisture advected by the ARs, and a high percentage of the total precipitation produced by the systems have a tropical origin. The tropical contribution to precipitation is in general above 50 % and largely exceeds this value in the most affected areas. Local convergence transport is responsible for the remaining moisture and precipitation. The ratio of tropical moisture to total moisture is maximized as the cold front arrives on land. Vertical cross sections of the moisture content suggest that the maximum in tropical humidity does not necessarily coincide with the low-level jet (LLJ of the extratropical cyclone. Instead, the amount of tropical humidity is maximized in the lowest atmospheric level in southern latitudes and can be located above, below or ahead of the LLJ in northern latitudes in both analyzed cases.

[Influence of impurities on waste plastics pyrolysis: products and emissions].

Science.gov (United States)

Zhao, Lei; Wang, Zhong-Hui; Chen, De-Zhen; Ma, Xiao-Bo; Luan, Jian

2012-01-01

The study is aimed to evaluate the impact of impurities like food waste, paper, textile and especially soil on the pyrolysis of waste plastics. For this purpose, emissions, gas and liquid products from pyrolysis of waste plastics and impurities were studied, as well as the transfer of element N, Cl, S from the substrates to the pyrolysis products. It was found that the presence of food waste would reduce the heat value of pyrolysis oil to 27 MJ/kg and increase the moisture in the liquid products, therefore the food residue should be removed from waste plastics; and the soil, enhance the waste plastics' pyrolysis by improving the quality of gas and oil products. The presence of food residue, textile and paper leaded to higher gas emissions.

Effect of sugar addition on glass transition temperatures of cassava starch with low to intermediate moisture contents.

Science.gov (United States)

Figueroa, Yetzury; Guevara, Marvilan; Pérez, Adriana; Cova, Aura; Sandoval, Aleida J; Müller, Alejandro J

2016-08-01

This work studies how sucrose (S) addition modifies the thermal properties of cassava starch (CS). Neat CS and CS-S blends with 4, 6 and 8% sugar contents (CS-S-4%, CS-S-6% and CS-S-8%) were prepared and analyzed by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA), in a wide range of moisture levels (2-20%). In equilibrated samples with moisture contents lower than 10%, twoendothermic steps were observed during first DSC heating scans and two corresponding relaxation maxima in tan δ were detected by DMTA. The first transition, detected at around 45-55°C by both DSC and DMTA, is frequently found in starchy foods, while the second observed at higher temperatures is associated to the glass transition temperature of the blends. At higher moisture contents, only one thermal transition was observed. Samples analyzed immediately after cooling from the melt (i.e., after erasing their thermal history), exhibited a single glass transition temperature, regardless of their moisture content. Addition of sugar promotes water plasticization of CS only at high moisture contents. In the low moisture content range, anti-plasticization was observed for both neat and sugar-added CS samples. Addition of sugar decreases the moisture content needed to achieve the maximum value of the glass transition temperature before plasticization starts. The results of this work may be valuable for the study of texture establishment in low moisture content extruded food products. Copyright © 2016 Elsevier Ltd. All rights reserved.

A new probe for in situ TDR moisture measurement

Energy Technology Data Exchange (ETDEWEB)

Yokuda, E. (EG and G Idaho, Inc., Idaho Falls, ID (United States)); Smith, R. (Sonsub Services, Inc., Houston, TX (United States))

1993-01-01

This paper explains the development of a new Time Domain Reflectometry (TDR) probe which can be inserted through waste and soil to a depth of 14 feet with minimal labor and minimal soil disturbance. TDR has been used for 10 years as a method for measuring soil moisture contents. Conventional TDR probes are 30 centimeters long and therefore are difficult to insert at depths below a few feet. Recently, a probe has been developed which can be inserted to depths of 14 feet with the use of a vibratory drill. Quality objectives for the instrument, preliminary data, and suggestions for future developments are presented.

A new probe for in situ TDR moisture measurement

International Nuclear Information System (INIS)

Yokuda, E.; Smith, R.

1993-01-01

This paper explains the development of a new Time Domain Reflectometry (TDR) probe which can be inserted through waste and soil to a depth of 14 feet with minimal labor and minimal soil disturbance. TDR has been used for 10 years as a method for measuring soil moisture contents. Conventional TDR probes are 30 centimeters long and therefore are difficult to insert at depths below a few feet. Recently, a probe has been developed which can be inserted to depths of 14 feet with the use of a vibratory drill. Quality objectives for the instrument, preliminary data, and suggestions for future developments are presented

A new probe for in situ TDR moisture measurement

Energy Technology Data Exchange (ETDEWEB)

Yokuda, E. [EG and G Idaho, Inc., Idaho Falls, ID (United States); Smith, R. [Sonsub Services, Inc., Houston, TX (United States)

1993-05-01

This paper explains the development of a new Time Domain Reflectometry (TDR) probe which can be inserted through waste and soil to a depth of 14 feet with minimal labor and minimal soil disturbance. TDR has been used for 10 years as a method for measuring soil moisture contents. Conventional TDR probes are 30 centimeters long and therefore are difficult to insert at depths below a few feet. Recently, a probe has been developed which can be inserted to depths of 14 feet with the use of a vibratory drill. Quality objectives for the instrument, preliminary data, and suggestions for future developments are presented.

Statistical analysis of simulated global soil moisture and its memory in an ensemble of CMIP5 general circulation models

Science.gov (United States)

Wiß, Felix; Stacke, Tobias; Hagemann, Stefan

2014-05-01

Soil moisture and its memory can have a strong impact on near surface temperature and precipitation and have the potential to promote severe heat waves, dry spells and floods. To analyze how soil moisture is simulated in recent general circulation models (GCMs), soil moisture data from a 23 model ensemble of Atmospheric Model Intercomparison Project (AMIP) type simulations from the Coupled Model Intercomparison Project Phase 5 (CMIP5) are examined for the period 1979 to 2008 with regard to parameterization and statistical characteristics. With respect to soil moisture processes, the models vary in their maximum soil and root depth, the number of soil layers, the water-holding capacity, and the ability to simulate freezing which all together leads to very different soil moisture characteristics. Differences in the water-holding capacity are resulting in deviations in the global median soil moisture of more than one order of magnitude between the models. In contrast, the variance shows similar absolute values when comparing the models to each other. Thus, the input and output rates by precipitation and evapotranspiration, which are computed by the atmospheric component of the models, have to be in the same range. Most models simulate great variances in the monsoon areas of the tropics and north western U.S., intermediate variances in Europe and eastern U.S., and low variances in the Sahara, continental Asia, and central and western Australia. In general, the variance decreases with latitude over the high northern latitudes. As soil moisture trends in the models were found to be negligible, the soil moisture anomalies were calculated by subtracting the 30 year monthly climatology from the data. The length of the memory is determined from the soil moisture anomalies by calculating the first insignificant autocorrelation for ascending monthly lags (insignificant autocorrelation folding time). The models show a great spread of autocorrelation length from a few months in

The TEES process cleans waste and produces energy

International Nuclear Information System (INIS)

Elliott, D.C.; Silva, L.J.

1995-02-01

A gasification system is under development that can be used with most types of wet organic wastes. The system operates at 350 degrees C and 205 atm using a liquid water phase as the processing medium. Since a pressurized system is used, the wet waste can be fed as a solution or slurry to the reactor without drying. Through the development of catalysts, a useful processing system has been produced. The system has utility both for direct conversion of high-moisture biomass to fuel gas or as a wastewater cleanup system for wet organic wastes including unconverted biomass from bioconversion processes. By the use of this system >99% conversions of organic waste to medium-Btu fuel gas can be achieved

The potentiation of zinc toxicity by soil moisture in a boreal forest ecosystem.

Science.gov (United States)

Owojori, Olugbenga J; Siciliano, Steven D

2015-03-01

Northern boreal forests often experience forest dieback as a result of metal ore mining and smelting. The common solution is to lime the soil, which increases pH, reducing metal toxicity and encouraging recovery. In certain situations, however, such as in Flin Flon, Manitoba, Canada, liming has yielded only moderate benefits, with some locations responding well to liming and other locations not at all. In an effort to increase the effectiveness of the ecorestoration strategy, the authors investigated if these differences in liming responsiveness were linked to differences in toxicity. Toxicity of metal-impacted Flin Flon soils on the oribatid mite Oppia nitens and the collembolan Folsomia candida was assessed, with a view toward identifying the metal of concern in the area. The effects of moisture content on metal sorption, uptake, and toxicity to the invertebrates were also investigated. Toxicity tests with the invertebrates were conducted using either Flin Flon soils or artificial soils with moisture content adjusted to 30%, 45%, 60%, or 75% of the maximum water-holding capacity of the soil samples. The Relative to Cd Toxicity Model identified Zn as the metal of concern in the area, and this was confirmed using validation tests with field contaminated soils. Furthermore, increasing the moisture content in soils increased the amount of mobile Zn available for uptake with the ion exchange resin. Survival and reproduction of both invertebrates were reduced under Zn exposure as moisture level increased. Thus, moisture-collecting landforms, which are often also associated with high Zn concentrations at Flin Flon, have, as a result, higher Zn toxicity to the soil ecosystem because of increases in soil moisture. © 2014 SETAC.

Analysis of near-field thermal and psychometric waste package environment using ventilation

International Nuclear Information System (INIS)

Danko, G.

1995-03-01

The ultimate objective of the Civilian Radioactive Waste Management System (CRWMS) Program is to safely emplace and isolate the nations' spent nuclear fuel (SNF) and radioactive wastes in a geologic repository. Radioactive waste emplaced in a geologic repository will generate heat, increasing the temperature in the repository. The magnitude of this temperature increase depends upon (1) the heat source, i.e. the thermal loading of the repository, and (2) the geologic and engineered heat transport characteristics of the repository. Thermal management techniques currently under investigation include ventilation of the emplacement drifts during the preclosure period which could last as long as 100 years. Understanding the amount of heat and moisture removed from the emplacement drifts and near-field rock by ventilation, are important in determining performance of the engineered barrier system (EBS), as well as the corrosive environment of the waste packages, and the interaction of the EBS with the near-field host rock. Since radionuclide releases and repository system performance are significantly affected by the corrosion rate related to the psychometric environment, it is necessary to predict the amount of heat and moisture that are removed from the repository horizon using a realistic model for a wide range of thermal loading. This can be realized by coupling the hydrothermal model of the rock mass to a ventilation/climate model which includes the heat and moisture transport on the rock-air interface and the dilution of water vapor in the drift. This paper deals with the development of the coupled model concept, and determination of the boundary conditions for the calculations

Geo-environmental application of municipal solid waste incinerator ash stabilized with cement

Directory of Open Access Journals (Sweden)

Davinder Singh

2017-04-01

Full Text Available The behavior of soluble salts contained in the municipal solid waste incinerator (MSWI ash significantly affects the strength development and hardening reaction when stabilized with cement. The present study focuses on the compaction and strength behavior of mixed specimens of cement and MSWI ash. A series of indices such as unconfined compressive strength, split tensile strength, California bearing ratio (CBR and pH value was examined. Prior to this, the specimens were cured for 7 d, 14 d, and 28 d. The test results depict that the maximum dry density (MDD decreases and the optimum moisture content (OMC increases with the addition of cement. The test results also reveal that the cement increases the strength of the mixed specimens. Thus, the combination of MSWI ash and cement can be used as a lightweight filling material in different structures like embankment and road construction.

Management of domestic solid wastes at the Akwapim South Municipality: a case study

International Nuclear Information System (INIS)

Ackah, M.

2008-06-01

The key findings of a solid waste characterization study conducted at Nsawam and Adoagyiri of the Akwapim South Municipality are reported. Household waste generated by a number of residents of these two important towns of the Municipality, were collected through a two-way stratification based on differences in income levels and class of residential areas over a 12- week period, between December 2007 and March 2008. A total of 24 collections were made and about 2319 kg of household solid wastes were collected, weighed and classified according to the various components of the waste streams after thoroughly sorting the waste. Each component of the waste stream (i.e. organic, paper, plastics, metals/cans, textiles, glass, inert materials/residues and miscellaneous components) was then reweighed and the weights recorded. Information on demographics such as household size, characteristics and detailed information on household waste management practices of the study areas were obtained through a self administered questionnaire. Other physico-chemical characteristics of the collected household solid waste such as moisture content, density and volumes and heavy metals were measured. The average waste composition from Nsawam were 62% organic component, 7% paper and card component, 8% plastic and rubber component, 1 % glass component, 3% metal/can component, 2% textile component, 14% residues or inert materials and 3% miscellaneous or other waste component. However, for Adoagyiri, average composition revealed 50% organic component, 10% paper component, 12% plastics and rubber, 3% glass, 4% metal, 2 % textile, 15% residues or inert materials and 4% miscellaneous or other waste. The study also sought to examine the extent to which household demographics influenced waste stream character. Physico-chemical analysis was also conducted on composite samples of domestic solid waste from the two towns. The results of this analysis yielded information on the compostable and combustible

Effects of moisture barrier and initial moisture content on the storage ...

African Journals Online (AJOL)

The two factors examined were moisture barrier at three levels namely: thick lining, thin lining and non-lining. The other factor included initial moisture content of the produce, namely, turgid and partially wilted. Partial wilting of the produce was achieved by exposing freshly harvested materials at ambient temperature to dry ...

Solid waste combustion for alpha waste incineration

International Nuclear Information System (INIS)

Orloff, D.I.

1981-02-01

Radioactive waste incinerator development at the Savannah River Laboratory has been augmented by fundamental combustion studies at the University of South Carolina. The objective was to measure and model pyrolysis and combustion rates of typical Savannah River Plant waste materials as a function of incinerator operating conditions. The analytical models developed in this work have been incorporated into a waste burning transient code. The code predicts maximum air requirement and heat energy release as a function of waste type, package size, combustion chamber size, and temperature. Historically, relationships have been determined by direct experiments that did not allow an engineering basis for predicting combustion rates in untested incinerators. The computed combustion rates and burning times agree with measured values in the Savannah River Laboratory pilot (1 lb/hr) and full-scale (12 lb/hr) alpha incinerators for a wide variety of typical waste materials

7 CFR 52.3185 - Moisture limits.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Moisture limits. 52.3185 Section 52.3185 Agriculture... United States Standards for Grades of Dried Prunes Moisture, Uniformity of Size, Defects § 52.3185 Moisture limits. Dried prunes shall not exceed the moisture limits for the applicable grades and kind and...

7 CFR 868.258 - Moisture.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Moisture. 868.258 Section 868.258 Agriculture... Governing Application of Standards § 868.258 Moisture. Water content in brown rice for processing as... purpose of this paragraph, “approved device” shall include the Motomco Moisture Meter and any other...

Hyperspectral Reflectance Imaging Technique for Visualization of Moisture Distribution in Cooked Chicken Breast

Directory of Open Access Journals (Sweden)

Byoung-Kwan Cho

2013-09-01

Full Text Available Spectroscopy has proven to be an efficient tool for measuring the properties of meat. In this article, hyperspectral imaging (HSI techniques are used to determine the moisture content in cooked chicken breast over the VIS/NIR (400–1,000 nm spectral range. Moisture measurements were performed using an oven drying method. A partial least squares regression (PLSR model was developed to extract a relationship between the HSI spectra and the moisture content. In the full wavelength range, the PLSR model possessed a maximum  of 0.90 and an SEP of 0.74%. For the NIR range, the PLSR model yielded an  of 0.94 and an SEP of 0.71%. The majority of the absorption peaks occurred around 760 and 970 nm, representing the water content in the samples. Finally, PLSR images were constructed to visualize the dehydration and water distribution within different sample regions. The high correlation coefficient and low prediction error from the PLSR analysis validates that HSI is an effective tool for visualizing the chemical properties of meat.

Effect of pH, temperature and moisture content during composting of rice straw burning at different temperature with food waste and effective microorganisms

Directory of Open Access Journals (Sweden)

Zakarya Irnis Azura

2018-01-01

Full Text Available Rice straw is considered as one of the most important agricultural residues and represented as one of the major by-products from rice production process. Normally, rice straw that produced after harvesting season been directly burned on-farm. Conversion of rice straw into value added compost will improve the productivity of plant, reduction of pollution towards environment and reduction of local pollution due to open burning activity. The objective of this study was to evaluate the performance of composting rice straw ash (RSA with food waste (FW and effective microorganisms (EM in term of the compost quality (pH, temperature, moisture content. RSA was prepared by burning the raw rice straw at three different temperature of 300°C, 400°C and 500°C for one hour. EM used during the composting process was prepared by mixing of brown sugar, ‘tempe’ and water that can be used after one week of fermentation process. There are four treatments of RSA-compost; RSA (300°C, RSA (400°C, RSA (500°C and control (raw rice straw with the same amount of compost medium; 1kg black soil, 0.5kg RSA, 3L EM and 1kg FW. The composting process happens for 30 days. During the composting process, all the parameters of RSA-compost obtained in a range like; pH value 8-10, temperature 20-50°C and moisture content 40-60%. The result showed that all compost quality of rice straw ash compost obtained in an acceptable range for final compost to establish.

Effects of biodrying process on municipal solid waste properties.

Science.gov (United States)

Tambone, F; Scaglia, B; Scotti, S; Adani, F

2011-08-01

In this paper, the effect of biodrying process on municipal solid waste (MSW) properties was studied. The results obtained indicated that after 14d, biodrying reduced the water content of waste, allowing the production of biodried waste with a net heating value (NHV) of 16,779±2,074kJ kg(-1) wet weight, i.e. 41% higher than that of untreated waste. The low moisture content of the biodried material reduced, also, the potential impacts of the waste, i.e. potential self-ignition and potential odors production. Low waste impacts suggest to landfill the biodried material obtaining energy via biogas production by waste re-moistening, i.e. bioreactor. Nevertheless, results of this work indicate that biodrying process because of the partial degradation of the organic fraction contained in the waste (losses of 290g kg(-1) VS), reduced of about 28% the total producible biogas. Copyright © 2011 Elsevier Ltd. All rights reserved.

Errors in the calculation of sub-soil moisture probe by equivalent moisture content technique

International Nuclear Information System (INIS)

Lakshmipathy, A.V.; Gangadharan, P.

1982-01-01

The size of the soil sample required to obtain the saturation response, with a neutron moisture probe is quite large and this poses practical problems of handling and mixing large amounts of samples for absolute laboratory calibration. Hydrogenous materials are used as a substitute for water in the equivalent moisture content technique, for calibration of soil moisture probes. In this it is assumed that only hydrogen of the bulk sample is responsible for the slowing down of fast neutrons and the slow neutron countrate is correlated to equivalent water content by considering the hydrogen density of sample. It is observed that the higher atomic number elements present in water equivalent media also affect the response of the soil moisture probe. Hence calculations, as well as experiments, were undertaken to know the order of error introduced by this technique. The thermal and slow neutron flux distribution around the BF 3 counter of a sub-soil moisture probe is calculated using three group diffusion theory. The response of the probe corresponding to different equivalent moisture content of hydrogenous media, is calculated taking into consideration the effective length of BF 3 counter. Soil with hydrogenous media such as polyethylene, sugar and water are considered for calculation, to verify the suitability of these materials as substitute for water during calibration of soil moisture probe. Experiments were conducted, to verify the theoretically calculated values. (author)

Method of estimating maximum VOC concentration in void volume of vented waste drums using limited sampling data: Application in transuranic waste drums

International Nuclear Information System (INIS)

Liekhus, K.J.; Connolly, M.J.

1995-01-01

A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds (VOCs) within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles as well as limited waste drum sampling data. The model consists of a series of material balance equations describing steady-state VOC transport from each distinct void volume in the drum. The primary model input is the measured drum headspace VOC concentration. Model parameters are determined or estimated based on available process knowledge. The model effectiveness in estimating VOC concentration in the headspace of the innermost layer of confinement was examined for vented waste drums containing different waste types and configurations. This paper summarizes the experimental measurements and model predictions in vented transuranic waste drums containing solidified sludges and solid waste

Impact of socioeconomic status on municipal solid waste generation rate.

Science.gov (United States)

Khan, D; Kumar, A; Samadder, S R

2016-03-01

The solid waste generation rate was expected to vary in different socioeconomic groups due to many environmental and social factors. This paper reports the assessment of solid waste generation based on different socioeconomic parameters like education, occupation, income of the family, number of family members etc. A questionnaire survey was conducted in the study area to identify the different socioeconomic groups that may affect the solid waste generation rate and composition. The average waste generated in the municipality is 0.41 kg/capita/day in which the maximum waste was found to be generated by lower middle socioeconomic group (LMSEG) with average waste generation of 0.46 kg/capita/day. Waste characterization indicated that there was no much difference in the composition of wastes among different socioeconomic groups except ash residue and plastic. Ash residue is found to increase as we move lower down the socioeconomic groups with maximum (31%) in lower socioeconomic group (LSEG). The study area is a coal based city hence application of coal and wood as fuel for cooking in the lower socioeconomic group is the reason for high amount of ash content. Plastic waste is maximum (15%) in higher socioeconomic group (HSEG) and minimum (1%) in LSEG. Food waste is a major component of generated waste in almost every socioeconomic group with maximum (38%) in case of HSEG and minimum (28%) in LSEG. This study provides new insights on the role of various socioeconomic parameters on generation of household wastes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Gas generation from radiolytic attack of TRU-contaminated hydrogenous waste

International Nuclear Information System (INIS)

Zerwekh, A.

1979-06-01

In 1970, the Waste Management and Transportation Division of the Atomic Energy Commission ordered a segregation of transuranic (TRU)-contaminated solid wastes. Those below a contamination level of 10 nCi/g could still be buried; those above had to be stored retrievably for 20 y. The possibility that alpha-radiolysis of hydrogenous materials might produce toxic, corrosive, and flammable gases in retrievably stored waste prompted an investigation of gas identities and generation rates in the laboratory and field. Typical waste mixtures were synthesized and contaminated for laboratory experiments, and drums of actual TRU-contaminated waste were instrumented for field testing. Several levels of contamination were studied, as well as pressure, temperature, and moisture effects. G (gas) values were determined for various waste matrices, and degradation products were examined

Soil moisture variability across different scales in an Indian watershed for satellite soil moisture product validation

KAUST Repository

Singh, Gurjeet

2016-05-05

Strategic ground-based sampling of soil moisture across multiple scales is necessary to validate remotely sensed quantities such as NASA’s Soil Moisture Active Passive (SMAP) product. In the present study, in-situ soil moisture data were collected at two nested scale extents (0.5 km and 3 km) to understand the trend of soil moisture variability across these scales. This ground-based soil moisture sampling was conducted in the 500 km2 Rana watershed situated in eastern India. The study area is characterized as sub-humid, sub-tropical climate with average annual rainfall of about 1456 mm. Three 3x3 km square grids were sampled intensively once a day at 49 locations each, at a spacing of 0.5 km. These intensive sampling locations were selected on the basis of different topography, soil properties and vegetation characteristics. In addition, measurements were also made at 9 locations around each intensive sampling grid at 3 km spacing to cover a 9x9 km square grid. Intensive fine scale soil moisture sampling as well as coarser scale samplings were made using both impedance probes and gravimetric analyses in the study watershed. The ground-based soil moisture samplings were conducted during the day, concurrent with the SMAP descending overpass. Analysis of soil moisture spatial variability in terms of areal mean soil moisture and the statistics of higher-order moments, i.e., the standard deviation, and the coefficient of variation are presented. Results showed that the standard deviation and coefficient of variation of measured soil moisture decreased with extent scale by increasing mean soil moisture. © (2016) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

Integrated Waste Treatment Unit (IWTU) Input Coal Analyses and Off-Gass Filter (OGF) Content Analyses

Energy Technology Data Exchange (ETDEWEB)

Jantzen, Carol M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, David M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Guenther, Chris P. [National Energy Technology Lab. (NETL), Morgantown, WV (United States); Shekhawat, Dushyant [National Energy Technology Lab. (NETL), Morgantown, WV (United States); VanEssendelft, Dirk T. [National Energy Technology Lab. (NETL), Morgantown, WV (United States); Means, Nicholas C. [AECOM Technology Corp., Oak Ridge, TN (United States)

2015-04-23

A full engineering scale Fluidized Bed Steam Reformer (FBSR) system is being used at the Idaho Nuclear Technology and Engineering Center (INTEC) to stabilize acidic Low Activity Waste (LAW) known as Sodium Bearing Waste (SBW). The INTEC facility, known as the Integrated Waste Treatment Unit (IWTU), underwent an Operational Readiness Review (ORR) and a Technology Readiness Assessment (TRA) in March 2014. The IWTU began non-radioactive simulant processing in late 2014 and by January, 2015 ; the IWTU had processed 62,000 gallons of simulant. The facility is currently in a planned outage for inspection of the equipment and will resume processing simulated waste feed before commencing to process 900,000 gallons of radioactive SBW. The SBW acidic waste will be made into a granular FBSR product (carbonate based) for disposal in the Waste Isolation Pilot Plant (WIPP). In the FBSR process calcined coal is used to create a CO2 fugacity to force the waste species to convert to carbonate species. The quality of the coal, which is a feed input, is important because the reactivity, moisture, and volatiles (C,H,N,O, and S) in the coal impact the reactions and control of the mineralizing process in the primary steam reforming vessel, the Denitration and Mineralizing Reformer (DMR). Too much moisture in the coal can require that additional coal be used. However since moisture in the coal is only a small fraction of the moisture from the fluidizing steam this can be self-correcting. If the coal reactivity or heating value is too low then the coal feedrate needs to be adjusted to achieve the desired heat generation. Too little coal and autothermal heat generation in the DMR cannot be sustained and/or the carbon dioxide fugacity will be too low to create the desired carbonate mineral species. Too much coal and excess S and hydroxide species can form. Excess sulfur from coal that (1) is too rich in sulfur or (2) from overfeeding coal can promote wall scale and contribute to corrosion

Treatment of organic solid waste for reuse: a step towards zero waste

International Nuclear Information System (INIS)

Ali, M.; Khan, Z.M.; Raja, I.A.

2013-01-01

Large amounts of organic solid wastes are being generated from municipal, industrial and agricultural activities. After necessary processing, the organic solid waste can be reused for agriculture not only as a nutrient supplement for plant growth, but also as a conditioner for seedbed soil. Processed organic wastes may improve soil structure and enhance water and nutrient-holding capacity of the soil, as well as increase the microbial activity within the soil, thereby increasing soil fertility. In this study, problems like undesirably high moisture contents and large volumes per unit weight of the processed organic solid wastes have been addressed through pelletization. Physical properties like durability, percent of fines content, and bulk and particle density of the processed and pelletized organic waste have been investigated, and the optimum values for storage, handling and transportation of the pelletized organic waste have been determined. Three different sizes of extruding sieve (4.35, 6.35 and 7.9 mm) and three different waste-mixing ratios (1:1:2, 1:2:2 and 1:3:3) of farmyard waste, wastewater sludge and sugar industry press mud were used respectively for the production of bio-solid pellets. The physical properties of the palletes show that durability increases by increasing the amount of sewage sludge while fines content, bulk density and unit density decrease. The large sieve size has more durability and less fine content. The results showed that the pelletization technique can be efficiently used by the farmers and appears to be a good option for sustainable management and re-use of organic solid wastes. (author)

Composting of high moisture content swine manure with corncob in a pilot-scale aerated static bin system.

Science.gov (United States)

Zhu, Nengwu

2006-10-01

Pilot composting experiments of swine manure with corncob were conducted to evaluate the performance of the aerated static bin composting system. Effects of temperature control (60 and 70 degrees C) and moisture content (70% and 80%) were monitored on the composting by measuring physical and chemical indexes. The results showed that (1) the composting system could destroy pathogens, converted nitrogen from unstable ammonia to stable organic forms, and reduced the volume of waste; (2) significant difference of NH(4)(+)-N (P(12) = 0.074), and (NO(3)(-) + NO(2)(-))-N (P(12) = 0.085) was found between the temperature control treatments; (3) anaerobic reaction in the treatment with 80% moisture content resulted in significant difference of pH (P(23) = 0.006), total organic matter (P(23) = 0.003), and germination index (P(23) = 0.040) between 70% and 80%. Therefore, the optimum initial moisture content was less than 80% with the composting of swine manure and corncob by using the composting system.

Water dynamics of Ser-His-Glu-Cys-Asn powder and effects of moisture absorption on its chemical properties.

Science.gov (United States)

Lin, Songyi; Xue, Peiyu; Yang, Shuailing; Li, Xingfang; Dong, Xiuping; Chen, Feng

2017-08-01

This study has elucidated moisture dynamics in the soybean peptide, Ser-His-Glu-Cys-Asn (SHECN) powder by using dynamic vapor sorption (DVS) and nuclear magnetic resonance (NMR). We also tried to investigate the effects of moisture absorption on the biological activity and chemical properties of SHECN with some effective methods such as mid-infrared (MIR) spectroscopy and gas chromatography-mass spectrometry (GC-MS). DVS results showed that the moisture absorption of SHECN could reach a maximum of 33%, and the SHECN powder after synthesis actually existed in a trihydrate state of SHECN.3H 2 O. Low-field NMR revealed that three water proportions including strong combined water, binding water and bulk water were involved in SHECN moisture absorption and absored water dominantly existed in the form of combined water. Magnetic resonance imaging (MRI) and MIR spectroscopy results indicated that moisture absorption could change the morphology and structure of SHECN. After moisture absorption at 50% and 75% relative humidity, 19 volatiles were identified by GC-MS analysis. Additionally, this study showed that a part of reductive groups in SHECN was oxidized and its antioxidant ability declined significantly (P moisture absorption. Water absorbed into SHECN powder can significantly change its microstructure and cause its activity to decrease. We must prevent SHECN from absorbing moisture during storage because the water can accelerate the oxidation of samples and promote microbial reactions. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Process for treatment of detergent-containing radioactive liquid wastes

International Nuclear Information System (INIS)

Kamiya, K.; Chino, K.; Funabashi, K.; Horiuchi, S.; Motojima, K.

1984-01-01

A detergent-containing radioactive liquid waste originating from atomic power plants is concentrated to have about 10 wt. % detergent concentration, then dried in a thin film evaporator, and converted into powder. Powdered activated carbon is added to the radioactive waste in advance to prevent the liquid waste from foaming in the evaporator by the action of surface active agents contained in the detergent. The activated carbon is added in accordance with the COD concentration of the radioactive liquid waste to be treated, and usually at a concentration 2-4 times as large as the COD concentration of the liquid waste to be treated. A powdery product having a moisture content of not more than 15 wt. % is obtained from the evaporator, and pelletized and then packed into drums to be stored for a predetermined period

Effects of perched water on thermally driven moisture flow at the proposed Yucca Mountain repository for high-level waste

International Nuclear Information System (INIS)

Ofoegbu, G.I.; Bagtzoglou, A.C.; Green, R.T.; Muller, M.A.

1999-01-01

Numerical modeling was conducted to identify potential perched-water sites and examine the effects of perched water on thermally driven moisture flow at the proposed Yucca Mountain repository for high-level nuclear waste. It is demonstrated that perched-water zones may occur at two horizons on the up-dip side of faults such as the Ghost Dance Fault (GDF): in nonwelded volcanic strata [such as the Paintbrush Tuff nonwelded (PTn) stratigraphic unit], where juxtaposition of welded strata against nonwelded may constitute a barrier to lateral flow within the nonwelded strata; and in fractured horizons of underlying welded units [such as the Topopah Spring welded (TSw) unit] because of focused infiltration fed by overlying perched zones. The potential perched zones (PPZs) may contain perched water (which would flow freely into a well or opening) if infiltration rates are high enough. At lower infiltration rates, the PPZs contain only capillary-held water at relatively high saturations. Areas of the proposed repository that lie below PPZs are likely to experience relatively high percolation flux even if the PPZ contains only capillary-held water at high saturation. As a result, PPZs that contain only capillary-held water may be as important to repository performance as those that contain perched water. Thermal loading from emplaced waste in the repository is not likely to have an effect on PPZs located on adequate distance above the repository (such as in the PTn). As a result, such PPZs may be considered as permanent features of the environment. On the other hand, PPZs close to the repository depth (such as those that may occur in the TSw rock unit) would experience an initial period of spatial growth and increased saturation following waste emplacement. Thereafter, drying would begin at the repository horizon with perched-zone growth simultaneously above and below the repository. As a result, after the initial period of expansion, PPZs close to the repository horizon

Use of Soil Moisture Variability in Artificial Neural Network Retrieval of Soil Moisture

Directory of Open Access Journals (Sweden)

Bert Veenendaal

2009-12-01

Full Text Available Passive microwave remote sensing is one of the most promising techniques for soil moisture retrieval. However, the inversion of soil moisture from brightness temperature observations is not straightforward, as it is influenced by numerous factors such as surface roughness, vegetation cover, and soil texture. Moreover, the relationship between brightness temperature, soil moisture and the factors mentioned above is highly non-linear and ill-posed. Consequently, Artificial Neural Networks (ANNs have been used to retrieve soil moisture from microwave data, but with limited success when dealing with data different to that from the training period. In this study, an ANN is tested for its ability to predict soil moisture at 1 km resolution on different dates following training at the same site for a specific date. A novel approach that utilizes information on the variability of soil moisture, in terms of its mean and standard deviation for a (sub region of spatial dimension up to 40 km, is used to improve the current retrieval accuracy of the ANN method. A comparison between the ANN with and without the use of the variability information showed that this enhancement enables the ANN to achieve an average Root Mean Square Error (RMSE of around 5.1% v/v when using the variability information, as compared to around 7.5% v/v without it. The accuracy of the soil moisture retrieval was further improved by the division of the target site into smaller regions down to 4 km in size, with the spatial variability of soil moisture calculated from within the smaller region used in the ANN. With the combination of an ANN architecture of a single hidden layer of 20 neurons and the dual-polarized brightness temperatures as input, the proposed use of variability and sub-region methodology achieves an average retrieval accuracy of 3.7% v/v. Although this accuracy is not the lowest as comparing to the research in this field, the main contribution is the ability of ANN in

Resource recovery from municipal solid waste by mechanical heat treatment: An opportunity

Science.gov (United States)

Kamaruddin, Mohamad Anuar; Yusoff, Mohd Suffian; Ibrahim, Nurazim; Zawawi, Mohd Hafiz

2017-04-01

Municipal solid waste (MSW) stream in Malaysia consists of 50 to 60 % of food wastes. In general, food wastes are commingled in nature and very difficult to be managed in sustainable manner due to high moisture content. Consequently, by dumping food wastes together with inert wastes to the landfill as final disposal destination incurs large space area and reducing the lifespan of landfill. Therefore, certain fraction of the MSW as such; food wastes (FW) can be diverted from total disposal at the landfill that can improve landfill lifespan and environmental conservation. This study aims to determine the resource characteristics of FW extracted from USM cafeteria by means of mechanical heat treatment in the presence of autoclaving technology. Sampling of FW were conducted by collecting FW samples from disposal storage at designated area within USM campus. FW characteristics was performed prior and autoclaving process. The results have demonstrated that bones fraction was the highest followed by vegetable and rice with 39, 27 and 10%, respectively. Meanwhile, based on autoclaving technique, moisture content of the FW (fresh waste) were able to be reduced ranging from 65-85% to 59-69% (treated waste). Meanwhile, chemical characteristics of treated FW results in pH, TOC, TKN, C/N ratio, TP, and TK 5.12, 27,6%, 1.6%, 17.3%, 0.9% and 0.36%. The results revealed that autoclaving technology is a promising approach for MSW diversion that can be transformed into useful byproducts such as fertilizer, RDF and recyclable items.

Bio-inspired, Moisture-Powered Hybrid Carbon Nanotube Yarn Muscles.

Science.gov (United States)

Kim, Shi Hyeong; Kwon, Cheong Hoon; Park, Karam; Mun, Tae Jin; Lepró, Xavier; Baughman, Ray H; Spinks, Geoffrey M; Kim, Seon Jeong

2016-03-14

Hygromorph artificial muscles are attractive as self-powered actuators driven by moisture from the ambient environment. Previously reported hygromorph muscles have been largely limited to bending or torsional motions or as tensile actuators with low work and energy densities. Herein, we developed a hybrid yarn artificial muscle with a unique coiled and wrinkled structure, which can be actuated by either changing relative humidity or contact with water. The muscle provides a large tensile stroke (up to 78%) and a high maximum gravimetric work capacity during contraction (2.17 kJ kg(-1)), which is over 50 times that of the same weight human muscle and 5.5 times higher than for the same weight spider silk, which is the previous record holder for a moisture driven muscle. We demonstrate an automatic ventilation system that is operated by the tensile actuation of the hybrid muscles caused by dew condensing on the hybrid yarn. This self-powered humidity-controlled ventilation system could be adapted to automatically control the desired relative humidity of an enclosed space.

Moisture Dynamics in Building Envelopes

DEFF Research Database (Denmark)

Peuhkuri, Ruut Hannele

2003-01-01

The overall scope of this Thesis "Moisture dynamics in building envelopes" has been to characterise how the various porous insulation materials investigated performed hygrothermally under conditions similar to those in a typical building envelope. As a result of the changing temperature...... part of the Thesis consists of a theory and literature review on the moisture storage and transport processes (Chapter 2), on the non-Fickian moisture transport (Chapter 3)and on the methods for determining the moisture properties (Chapter 4). In the second part, the conducted experimental work...

Moisture dynamics in building envelopes

Energy Technology Data Exchange (ETDEWEB)

Peuhkuri, R.

2003-07-01

The overall scope of this Thesis 'Moisture dynamics in building envelopes' has been to characterise how the various porous insulation materials investigated performed hygro thermally under conditions similar to those in a typical building envelope. As a result of the changing temperature and moisture conditions in the exterior weather and indoor climate the materials dynamically absorb and release moisture. The complexity of the impact of these conditions on the resulting moisture transport and content of the materials has been studied in this Thesis with controlled laboratory tests. (au)

7 CFR 868.207 - Moisture.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Moisture. 868.207 Section 868.207 Agriculture... Application of Standards § 868.207 Moisture. Water content in rough rice as determined by an approved device..., “approved device” shall include the Motomco Moisture Meter and any other equipment that is approved by the...

Processing and Pre-Treatment of Solid Radioactive Waste

Energy Technology Data Exchange (ETDEWEB)

Cerre, P. [Service de Controle des Radiations et de Genie Radioactif, Commissariat a L' Energie Atomique, Saclay (France)

1960-07-01

As solid radioactive waste varies in form, dimensions and volume, the Atomic Energy Commission first of all reduces the volume by breaking up and compressing the waste. Since the temporary storage of such waste is always attended by the risk of contamination, an efficient packing system has been devised and adopted. This consists of embedding the waste in the heart of a specially-designed block of concrete possessing the following characteristics: Great strength Maximum insolubility Resistance to corrosion Maximum imperviousness Protection against radiation. It is thus quite safe to store these blocks with a view to final dumping. (author)

Soil moisture variability across different scales in an Indian watershed for satellite soil moisture product validation

KAUST Repository

Singh, Gurjeet; Panda, Rabindra K.; Mohanty, Binayak P.; Jana, Raghavendra Belur

2016-01-01

Strategic ground-based sampling of soil moisture across multiple scales is necessary to validate remotely sensed quantities such as NASA’s Soil Moisture Active Passive (SMAP) product. In the present study, in-situ soil moisture data were collected

Native Plant Uptake Model for Radioactive Waste Disposal Areas at the Nevada Test Site

Energy Technology Data Exchange (ETDEWEB)

BROWN,THERESA J.; WIRTH,SHARON

1999-09-01

This report defines and defends the basic framework, methodology, and associated input parameters for modeling plant uptake of radionuclides for use in Performance Assessment (PA) activities of Radioactive Waste Management Sites (RWMS) at the Nevada Test Site (NTS). PAs are used to help determine whether waste disposal configurations meet applicable regulatory standards for the protection of human health, the environment, or both. Plants adapted to the arid climate of the NTS are able to rapidly capture infiltrating moisture. In addition to capturing soil moisture, plant roots absorb nutrients, minerals, and heavy metals, transporting them within the plant to the above-ground biomass. In this fashion, plant uptake affects the movement of radionuclides. The plant uptake model presented reflects rooting characteristics important to plant uptake, biomass turnover rates, and the ability of plants to uptake radionuclides from the soil. Parameters are provided for modeling plant uptake and estimating surface contaminant flux due to plant uptake under both current and potential future climate conditions with increased effective soil moisture. The term ''effective moisture'' is used throughout this report to indicate the soil moisture that is available to plants and is intended to be inclusive of all the variables that control soil moisture at a site (e.g., precipitation, temperature, soil texture, and soil chemistry). Effective moisture is a concept used to simplify a number of complex, interrelated soil processes for which there are too little data to model actual plant available moisture. The PA simulates both the flux of radionuclides across the land surface and the potential dose to humans from that flux. Surface flux is modeled here as the amount of soil contamination that is transferred from the soil by roots and incorporated into aboveground biomass. Movement of contaminants to the surface is the only transport mechanism evaluated with the model

Native Plant Uptake Model for Radioactive Waste Disposal Areas at the Nevada Test Site

International Nuclear Information System (INIS)

Brown, Theresa J.; Wirth, Sharon

1999-01-01

This report defines and defends the basic framework, methodology, and associated input parameters for modeling plant uptake of radionuclides for use in Performance Assessment (PA) activities of Radioactive Waste Management Sites (RWMS) at the Nevada Test Site (NTS). PAs are used to help determine whether waste disposal configurations meet applicable regulatory standards for the protection of human health, the environment, or both. Plants adapted to the arid climate of the NTS are able to rapidly capture infiltrating moisture. In addition to capturing soil moisture, plant roots absorb nutrients, minerals, and heavy metals, transporting them within the plant to the above-ground biomass. In this fashion, plant uptake affects the movement of radionuclides. The plant uptake model presented reflects rooting characteristics important to plant uptake, biomass turnover rates, and the ability of plants to uptake radionuclides from the soil. Parameters are provided for modeling plant uptake and estimating surface contaminant flux due to plant uptake under both current and potential future climate conditions with increased effective soil moisture. The term ''effective moisture'' is used throughout this report to indicate the soil moisture that is available to plants and is intended to be inclusive of all the variables that control soil moisture at a site (e.g., precipitation, temperature, soil texture, and soil chemistry). Effective moisture is a concept used to simplify a number of complex, interrelated soil processes for which there are too little data to model actual plant available moisture. The PA simulates both the flux of radionuclides across the land surface and the potential dose to humans from that flux. Surface flux is modeled here as the amount of soil contamination that is transferred from the soil by roots and incorporated into aboveground biomass. Movement of contaminants to the surface is the only transport mechanism evaluated with the model presented here

Fuel Pellets Production from Biodiesel Waste

Directory of Open Access Journals (Sweden)

Kawalin Chaiyaomporn

2010-01-01

Full Text Available This research palm fiber and palm shell were used as raw materials to produce pelletised fuel, and waste glycerol were used as adhesive to reduce biodiesel production waste. The aim of this research is to find optimum ratio of raw material (ratio of palm fiber and palm shell, raw material size distribution, adhesive temperature, and ratio of ingredients (ratio of raw material, waste glycerol, and water. The optimum ratio of pelletized fuel made only by palm fiber was 50:10:40; palm fiber, water, and waste glycerol respectively. In the best practice condition; particle size was smaller than 2 mm, adhesive glycerol was heated. From the explained optimum ratio and ingredient, pelletizing ratio was 62.6%, specific density was 982.2 kg/m3, heating value was 22.5 MJ/kg, moisture content was 5.9194%, volatile matter was 88.2573%, fix carbon content was 1.5894%, and ash content was 4.2339% which was higher than the standard. Mixing palm shell into palm fiber raw material reduced ash content of the pellets. The optimum raw material ratio, which minimizes ash content, was 80 to 20 palm fiber and palm shell respectively. Adding palm shell reduced ash content to be 2.5247% which was higher than pelletized fuel standard but followed cubed fuel standard. At this raw material ratio, pelletizing ratio was 70.5%, specific density was 774.8 kg/m3, heating value was 19.71 MJ/kg, moisture content was 9.8137%, volatile matter was 86.2259%, fix carbon content was 1.4356%, and compressive force was 4.83 N. Pelletized fuel cost at optimum condition was 1.14 baht/kg.

Pyrolysis of Waste Castor Seed Cake: A Thermo-Kinetics Study

Directory of Open Access Journals (Sweden)

Abdullahi Muhammad Sokoto

2018-03-01

Full Text Available Biomass pyrolysis is a thermo-chemical conversion process that is of both industrial and ecological importance. The efficient chemical transformation of waste biomass to numerous products via pyrolysis reactions depends on process kinetic rates; hence the need for kinetic models to best design and operate the pyrolysis. Also, for an efficient design of an environmentally sustainable pyrolysis process of a specific lignocellulosic waste, a proper understanding of its thermo-kinetic behavior is imperative. Thus, pyrolysis kinetics of castor seed de-oiled cake (Ricinus communis using thermogravimetric technique was studied. The decomposition of the cake was carried out in a nitrogen atmosphere with a flow rate of 100mL min-1 from ambient temperature to 900 °C. The results of the thermal profile showed moisture removal and devolatilization stages, and maximum decomposition of the cake occurred at a temperature of 200-400 °C. The kinetic parameters such as apparent activation energy, pre-exponential factor, and order of reaction were determined using Friedman (FD, Kissinger-Akahira-Sunose (KAS, and Flynn-Wall-Ozawa (FWO kinetic models. The average apparent activation energy values of 124.61, 126.95 and 129.80 kJmol-1 were calculated from the slopes of the respective models. The apparent activation energy values obtained depends on conversion, which is an evidence of multi-step kinetic process during the pyrolytic decomposition of the cake. The kinetic data would be of immense benefit to model, design and develop a suitable thermo-chemical system for the conversion of waste de-oil cake to energy carrier.

Uranium (VI) Sorption and Transport in Unsaturated, Subsurface Hanford Site Sediments - Effect of Moisture Content and Sediment Texture: Final Report for Subtask 2b

International Nuclear Information System (INIS)

Gamerdinger, A.P.; Resch, C.T.; Kaplan, D.I.

1998-01-01

A series of experiments were conducted in fiscal year 1998 at the Pacific Northwest National Laboratory as part of the Immobilized Low-Activity Waste-Performance Assessment. These experiments evaluated the sorption and transport of uranium, U(VI), under conditions of partial moisture saturation that are relevant to arid region burial sites and vadose-zone far-field conditions at the Hanford Site. The focus was on measuring breakthrough curves (from which distribution coefficient [K d ] values can be calculated) for U(W) in three Hanford Site sediments that represent different texture classes in two unsaturated moisture conditions. Previous research showed that K d values measured during transport in unsaturated sediments varied with moisture saturation

The impact of cerium oxide nanoparticles on the physiology of soybean (Glycine max (L.) Merr.) under different soil moisture conditions.

Science.gov (United States)

Cao, Zhiming; Rossi, Lorenzo; Stowers, Cheyenne; Zhang, Weilan; Lombardini, Leonardo; Ma, Xingmao

2018-01-01

The ongoing global climate change raises concerns over the decreasing moisture content in agricultural soils. Our research investigated the physiological impact of two types of cerium oxide nanoparticles (CeO 2 NPs) on soybean at different moisture content levels. One CeO 2 NP was positively charged on the surface and the other negatively charged due to the polyvinylpyrrolidone (PVP) coating. The results suggest that the effect of CeO 2 NPs on plant photosynthesis and water use efficiency (WUE) was dependent upon the soil moisture content. Both types of CeO 2 NPs exhibited consistently positive impacts on plant photosynthesis at the moisture content above 70% of field capacity (θ fc ). Similar positive impact of CeO 2 NPs was not observed at 55% θ fc , suggesting that the physiological impact of CeO 2 NPs was dependent upon the soil moisture content. The results also revealed that V Cmax (maximum carboxylation rate) was affected by CeO 2 NPs, indicating that CeO 2 NPs affected the Rubisco activity which governs carbon assimilation in photosynthesis. In conclusion, CeO 2 NPs demonstrated significant impacts on the photosynthesis and WUE of soybeans and such impacts were affected by the soil moisture content. Graphical abstract Soil moisture content affects plant cerium oxide nanoparticle interactions.

Synthesis long life storage studies surface storage of vitrified wastes

International Nuclear Information System (INIS)

Beziat, A.; Breton, E.; Ranc, G.; Gaillard, J.P.; Lagrave, H.; Hollender, F.; Jourdain, F.; Piault, E.; Garnier, J.; Lamare, V.; Duret, B.; Helie, M.; Ferry, C.; Mijuin, D.; Gagnier, E.

2004-01-01

This document is realized in the framework of the axis 3 of the law of 1991 on the radioactive wastes management. It justifies the choices concerning long time surface storage installation of vitrified wastes, called high activity wastes. The long time of the installation would reach 300 years at the maximum. These wastes represent 1 % at the maximum, of radioactive wastes in France but 95 % of the whole radioactivity. Three main objectives were followed: provide a permanent containment of radionuclides; give the possibility of wastes containers retrieval at all the time; minimize the maintenance and the control. The results allow to conclude that the long time surface storage of high activity wastes is feasible. (A.L.B.)

Surface moisture estimation in urban areas

Science.gov (United States)

Jiang, Yitong

Surface moisture is an important parameter because it modifies urban microclimate and surface layer meteorology. The primary objectives of this paper are: 1) to analyze the impact of surface roughness from buildings on surface moisture in urban areas; and 2) to quantify the impact of surface roughness resulting from urban trees on surface moisture. To achieve the objectives, two hypotheses were tested: 1) the distribution of surface moisture is associated with the structural complexity of buildings in urban areas; and 2) The distribution and change of surface moisture is associated with the distribution and vigor of urban trees. The study area is Indianapolis, Indiana, USA. In the part of the morphology of urban trees, Warren Township was selected due to the limitation of tree inventory data. To test the hypotheses, the research design was made to extract the aerodynamic parameters, such as frontal areas, roughness length and displacement height of buildings and trees from Terrestrial and Airborne LiDAR data, then to input the aerodynamic parameters into the urban surface energy balance model. The methodology was developed for comparing the impact of aerodynamic parameters from LiDAR data with the parameters that were derived empirically from land use and land cover data. The analytical procedures are discussed below: 1) to capture the spatial and temporal variation of surface moisture, daily and hourly Land Surface Temperature (LST) were downscaled from 4 km to 1 km, and 960 m to 30 m, respectively, by regression between LST and various components that impact LST; 2) to estimate surface moisture, namely soil moisture and evapotranspiration (ET), land surfaces were classified into soil, vegetation, and impervious surfaces, using Linear Spectral Mixture Analysis (LSMA); 3) aerodynamic parameters of buildings and trees were extracted from Airborne and Terrestrial LiDAR data; 4) the Temperature-Vegetation-Index (TVX) method, and the Two-Source-Energy-Balance (TSEB

Characterization of household waste in Greenland

International Nuclear Information System (INIS)

Eisted, Rasmus; Christensen, Thomas H.

2011-01-01

The composition of household waste in Greenland was investigated for the first time. About 2 tonnes of household waste was sampled as every 7th bag collected during 1 week along the scheduled collection routes in Sisimiut, the second largest town in Greenland with about 5400 inhabitants. The collection bags were sorted manually into 10 material fractions. The household waste composition consisted primarily of biowaste (43%) and the combustible fraction (30%), including anything combustible that did not belong to other clean fractions as paper, cardboard and plastic. Paper (8%) (dominated by magazine type paper) and glass (7%) were other important material fractions of the household waste. The remaining approximately 10% constituted of steel (1.5%), aluminum (0.5%), plastic (2.4%), wood (1.0%), non-combustible waste (1.8%) and household hazardous waste (1.2%). The high content of biowaste and the low content of paper make Greenlandic waste much different from Danish household waste. The moisture content, calorific value and chemical composition (55 elements, of which 22 were below detection limits) were determined for each material fraction. These characteristics were similar to what has been found for material fractions in Danish household waste. The chemical composition and the calorific value of the plastic fraction revealed that this fraction was not clean but contained a lot of biowaste. The established waste composition is useful in assessing alternative waste management schemes for household waste in Greenland.

Treatment strategies for transuranic wastes

International Nuclear Information System (INIS)

Schneider, K.J.; Swanson, J.L.; Ross, W.A.; Allen, R.P.; Yasutake, K.M.

1986-01-01

This paper presents an analysis of treatment options or strategies for transuranic wastes expected to be generated at a commercial nuclear fuel reprocessing plant. Six potential options were analyzed, ranging from no treatment to maximum volume reduction and high quality waste forms. Economics for the total management of these (treatment, transportation, disposal) indicate life-cycle savings for extensive treatment are as high as $1.7 billion for 70,000 MTU. Evaluations of the waste processing and waste forms support the selection of a number of the extensive waste treatments. It is concluded that there are significant incentives for extensive treatment of transuranic wastes

Design of Stirrer Impeller with Variable Operational Speed for a Food Waste Homogenizer

Directory of Open Access Journals (Sweden)

Idris A. Kayode

2016-05-01

Full Text Available A conceptualized impeller called KIA is designed for impact agitation of food waste in a homogenizer. A comparative analysis of the performance of KIA is made with three conventional impeller types, Rushton, Anchor, and Pitched Blade. Solid–liquid mixing of a moisture-rich food waste is simulated under various operational speeds, in order to compare the dispersions and thermal distributions at homogenous slurry conditions. Using SolidWorks, the design of the impellers employs an Application Programming Interface (API which acts as the canvas for creating a graphical user interface (GUI for automation of its assembly. A parametric analysis of the homogenizer, at varying operational speeds, enables the estimation of the critical speed of the mixing shaft diameter and the deflection under numerous mixing conditions and impeller configurations. The numerical simulation of the moisture-rich food waste (approximated as a Newtonian carrot–orange soup is performed with ANSYS CFX v.15.0. The velocity and temperature field distribution of the homogenizer for various impeller rotational speeds are analyzed. It is anticipated that the developed model will help in the selection of a suitable impeller for efficient mixing of food waste in the homogenizer.

Treatment strategies for transuranic wastes

International Nuclear Information System (INIS)

Schneider, K.J.; Ross, W.A.; Swanson, J.L.; Allen, R.P.; Yasutake, K.M.

1986-01-01

This paper presents an analysis of treatment options or strategies for transuranic wastes expected to be generated at a commercial nuclear fuel reprocessing plant. Six potential options were analyzed, ranging from no treatment to maximum volume reduction and high quality waste forms. Economics for the total management of these wastes (treatment, transportation, disposal) indicate life-cycle savings for extensive treatment are as high as $1.7 billion for 70,000 MTU. Evaluations of the waste processing and waste forms support the selection of a number of the extensive waste treatments. It is concluded that there are significant incentives for extensive treatment of transuranic wastes

Measurement of soil moisture using gypsum blocks

DEFF Research Database (Denmark)

Friis Dela, B.

the building. Consequently, measuring the moisture of the surrounding soil is of great importance for detecting the source of moisture in a building. Up till now, information has been needed to carry out individual calibrations for the different types of gypsum blocks available on the market and to account......For the past 50 years, gypsum blocks have been used to determine soil moisture content. This report describes a method for calibrating gypsum blocks for soil moisture measurements. Moisture conditions inside a building are strongly influenced by the moisture conditions in the soil surrounding...

Water extraction from high moisture lignite by means of efficient integration of waste heat and water recovery technologies with flue gas pre-drying system

International Nuclear Information System (INIS)

Han, Xiaoqu; Yan, Junjie; Karellas, Sotirios; Liu, Ming; Kakaras, Emmanuel; Xiao, Feng

2017-01-01

Highlights: • Energy-saving potential of FPLPS in different cold-ends and lignite types is evaluated. • Water-saving of FPLPS is realized through recovery of water extracted from lignite. • Integrations of low pressure economizer and spray tower with FPLPS are proposed. • Thermodynamic and economic performances of different schemes are investigated. - Abstract: The flue gas pre-dried lignite-fired power system (FPLPS) integrates the fan mill flue gas dryer with an open pulverizing system and yields an increase of the boiler efficiency. Particularly, the dryer exhaust gas contains a large amount of vapor removed from high moisture lignite, which exhibits great potential for waste heat and water recovery. Two available options are considered to realize the extraction of water from lignite: the low pressure economizer (LPE) for water-cooled units and the spray tower (SPT) integrated with heat pump for air-cooled units. This paper aims at evaluating the energy saving and water recovery potentials of the FPLPS integrated with both schemes. Results showed that the plant efficiency improvement of the FPLPS at base case varied from 1.14% to 1.47% depending on the moisture content of raw lignite. The water recovery ratio and plant efficiency improvement in the optimal LPE scheme were 39.4% and 0.20%, respectively. In contrast, 83.3% of water recover ratio and 110.6 MW_t_h heat supply were achieved in the SPT system. Both schemes were economically feasible with discounted payback periods of around 3 years. Moreover, parametric analysis was conducted to examine the economic viability of both schemes with different lignite types and market factors.

Nevada Test Site, 2006 Waste Management Monitoring Report, Area 3 and Area 5 Radioactive Waste Management Sites

International Nuclear Information System (INIS)

David B. Hudson

2007-01-01

Environmental monitoring data were collected at and around the Area 3 and Area 5 Radioactive Waste Management Sites (RWMSs) at the Nevada Test Site. These data are associated with radiation exposure, air, groundwater, meteorology, vadose zone, subsidence, and biota. This report summarizes the 2006 environmental data to provide an overall evaluation of RWMS performance and to support environmental compliance and performance assessment (PA) activities. Some of these data (e.g., radiation exposure, air, and groundwater) are presented in other reports (U.S. Department of Energy, 2006; Warren and Grossman, 2007; National Security Technologies, LLC, 2007). Direct radiation monitoring data indicate that exposure levels around the RWMSs are at or below background levels. Air monitoring data at the Area 3 and Area 5 RWMSs indicate that tritium concentrations are slightly above background levels. There is no detectable man-made radioactivity by gamma spectroscopy, and concentrations of americium and plutonium are only slightly above detection limits at the Area 3 RWMS. Measurements at the Area 5 RWMS show that radon flux from waste covers is no higher than natural radon flux from undisturbed soil in Area 5. Groundwater monitoring data indicate that the groundwater in the uppermost aquifer beneath the Area 5 RWMS is not impacted by facility operations. Precipitation during 2006 totaled 98.6 millimeters (mm) (3.9 inches [in.]) at the Area 3 RWMS and 80.7 mm (3.2 in.) at the Area 5 RWMS. Soil-gas tritium monitoring continues to show slow subsurface migration consistent with previous results. Moisture from precipitation at Area 5 remains at the bottom of the bare-soil weighing lysimeter, but this same moisture has been removed from the vegetated weighing lysimeter by evapotranspiration. Vadose zone data from the operational waste pit covers show that evaporation continues to slowly remove soil moisture that came from the heavy precipitation in the fall of 2004 and the spring of

Implications of moisture content determination in the environmental characterisation of FGD gypsum for its disposal in landfills

Energy Technology Data Exchange (ETDEWEB)

Alvarez-Ayuso, E. [Department of Environmental Geology, Institute of Earth Sciences ' Jaume Almera' (CSIC), C/ Lluis Sole i Sabaris s/n, 08028 Barcelona (Spain)], E-mail: ealvarez@ija.csic.es; Querol, X. [Department of Environmental Geology, Institute of Earth Sciences ' Jaume Almera' (CSIC), C/ Lluis Sole i Sabaris s/n, 08028 Barcelona (Spain); Tomas, A. [Endesa Generacion, S.A., C/ Ribera de Loira 60, 28042 Madrid (Spain)

2008-05-01

The leachable contents of elements of environmental concern considered in the Council Decision 2003/33/EC on waste disposal were determined in flue gas desulphurisation (FGD) gypsum. To this end, leaching tests were performed following the standard EN-12457-4 which specifies the determination of the dry mass of the material at 105 deg. C and the use of a liquid to solid (L/S) ratio of 10 l kg{sup -1} dry matter. Additionally, leaching tests were also carried out taking into account the dry mass of the material at 60 deg. C and using different L/S ratios (2, 5, 8, 10, 15 and 20 l kg{sup -1} dry matter). It was found that the dry mass determination at 105 deg. C turns out to be inappropriate for FGD gypsum since at this temperature gypsum transforms into bassanite, and so, in addition to moisture content, crystalline water is removed. As a consequence the moisture content is overvalued (about 16%), what makes consider a lower L/S ratio than that specified by the standard EN-12457-4. As a result the leachable contents in FGD gypsum are, in general, overestimated, what could lead to more strict environmental requirements for FGD gypsum when considering its disposal in landfills, specially concerning those elements (e.g., F) risking the characterisation of FGD gypsum as a waste acceptable at landfills for non-hazardous wastes.

Probing bias reduction to improve comparability of lint cotton water and moisture contents at moisture equilibrium

Science.gov (United States)

The Karl Fischer Titration (KFT) reference method is specific for water in lint cotton and was designed for samples conditioned to moisture equilibrium, thus limiting its biases. There is a standard method for moisture content – weight loss – by oven drying (OD), just not for equilibrium moisture c...

Permeability of different size waste particles

Directory of Open Access Journals (Sweden)

Sabina Gavelytė

2015-10-01

Full Text Available The world and life style is changing, but the most popular disposal route for waste is landfill globally until now. We have to think about waste prevention and preparing for re-use or recycling firstly, according to the waste disposal hierarchy. Disposed waste to the landfill must be the last opportunity. In a landfill, during waste degradation processes leachate is formed that can potentially cause clogging of bottom drainage layers. To ensure stability of a landfill construction, the physical properties of its components have to be controlled. The hydrology of precipitation, evaporation, runoff and the hydraulic performance of the capping and liner materials are important controls of the moisture content. The water balance depends also on the waste characteristics and waste particle size distribution. The aim of this paper is to determine the hydraulic permeability in a landfill depending on the particle size distribution of municipal solid waste disposed. The lab experiment results were compared with the results calculated with DEGAS model. Samples were taken from a landfill operated for five years. The samples particle sizes are: >100 mm, 80 mm, 60 mm, 40 mm, 20 mm, 0.01 mm and <0.01 mm. The permeability test was conducted using the column test. The paper presents the results of experiment and DEGAS model water permeability with waste particle size.

An overview of the measurements of soil moisture and modeling of moisture flux in FIFE

Science.gov (United States)

Wang, J. R.

1992-01-01

Measurements of soil moisture and calculations of moisture transfer in the soil medium and at the air-soil interface were performed over a 15-km by 15-km test site during FIFE in 1987 and 1989. The measurements included intensive soil moisture sampling at the ground level and surveys at aircraft altitudes by several passive and active microwave sensors as well as a gamma radiation device.

Red-Edge Spectral Reflectance as an Indicator of Surface Moisture Content in an Alaskan Peatland Ecosystem

Science.gov (United States)

McPartland, M.; Kane, E. S.; Turetsky, M. R.; Douglass, T.; Falkowski, M. J.; Montgomery, R.; Edwards, J.

2015-12-01

Arctic and boreal peatlands serve as major reservoirs of terrestrial organic carbon (C) because Net Primary Productivity (NPP) outstrips C loss from decomposition over long periods of time. Peatland productivity varies as a function of water table position and surface moisture content, making C storage in these systems particularly vulnerable to the climate warming and drying predicted for high latitudes. Detailed spatial knowledge of how aboveground vegetation communities respond to changes in hydrology would allow for ecosystem response to environmental change to be measured at the landscape scale. This study leverages remotely sensed data along with field measurements taken at the Alaska Peatland Experiment (APEX) at the Bonanza Creek Long Term Ecological Research site to examine relationships between plant solar reflectance and surface moisture. APEX is a decade-long experiment investigating the effects of hydrologic change on peatland ecosystems using water table manipulation treatments (raised, lowered, and control). Water table levels were manipulated throughout the 2015 growing season, resulting in a maximum separation of 35 cm between raised and lowered treatment plots. Water table position, soil moisture content, depth to seasonal ice, soil temperature, photosynthetically active radiation (PAR), CO2 and CH4 fluxes were measured as predictors of C loss through decomposition and NPP. Vegetation was surveyed for percent cover of plant functional types. Remote sensing data was collected during peak growing season, when the separation between treatment plots was at maximum difference. Imagery was acquired via a SenseFly eBee airborne platform equipped with a Canon S110 red-edge camera capable of detecting spectral reflectance from plant tissue at 715 nm band center to within centimeters of spatial resolution. Here, we investigate empirical relationships between spectral reflectance, water table position, and surface moisture in relation to peat carbon balance.

Compact RFID Enabled Moisture Sensor

Directory of Open Access Journals (Sweden)

U. H. Khan

2016-09-01

Full Text Available This research proposes a novel, low-cost RFID tag sensor antenna implemented using commercially available Kodak photo-paper. The aim of this paper is to investigate the possibility of stable, RFID centric communication under varying moisture levels. Variation in the frequency response of the RFID tag in presence of moisture is used to detect different moisture levels. Combination of unique jaw shaped contours and T-matching network is used for impedance matching which results in compact size and minimal ink consumption. Proposed tag is 1.4 × 9.4 cm2 in size and shows optimum results for various moisture levels upto 45% in FCC band with a bore sight read range of 12.1 m.

Influence of parameters and light e vironment under the canopy on the fuel moisture estimation model

International Nuclear Information System (INIS)

Tamai, K.; Goto, Y.

2006-01-01

Model parameterization was performed for estimation of the fuel moisture in adjacent plots with different tree species aiming at the mapping of forest fire hazard. One plot was covered with only deciduous species and the other with deciduous and evergreen trees. This model has our constant parameters. Three of them are for the relationship between evaporation and solar radiation. Another parameter is the maximum water content ratio of the litter. All of these parameters depend on the intrinsic drying properties of the litter. The water content ratio of the litter and solar radiation on the forest floor were measured in ach plot for one year. Parameters were fixed with the measured data. Though the parameter values were very different between the two plots, estimated moisture ratios were not so different. It was concluded that litter moisture depends on the microclimate, such as solar radiation, rather than on the intrinsic drying properties of the litter and litter layer

Neutron moisture monitoring (NMM) and moisture contents in the Green River, Utah, UMTRA disposal cell

International Nuclear Information System (INIS)

1992-06-01

This report provides the basis for the US Department of Energy's (DOE) request to discontinue neutron moisture monitoring (NMM) at the Green River, Utah, Uranium Mill Tailings Remedial Action (UMTRA) disposal cell and decommission the neutron access holes. After 3 years of monitoring the disposal cell, the DOE has determined that the NMM method is not suitable for determining changes in moisture content in the disposal cell. Existing tailings moisture contents in the disposal cell result in a low seepage flux. The combination of a low seepage flux and geochemical retardation by foundation materials underneath the disposal cell ensures that the proposed US Environmental Protection Agency (EPA) groundwater protection standards will not be exceeded within the design life of the disposal cell. To assess the effectiveness of the NMM method for monitoring moisture contents In the disposal cell at Green River, the DOE subsequently conducted a field study and a review of historical and new literature. The literature review allowed the DOE to identify performance criteria for the NMM method. Findings of these studies suggest that: The NMM method is not sensitive to the low moisture contents found in the disposal cell.; there is an insufficient range of moisture contents in the disposal cell to develop a field calibration curve relating moisture content to neutron counts; it is not possible to collect NMM data from the disposal cell that meet data quality objectives for precision and accuracy developed from performance criteria described in the literature

On-irrigator pasture soil moisture sensor

International Nuclear Information System (INIS)

Tan, Adrian Eng-Choon; Richards, Sean; Platt, Ian; Woodhead, Ian

2017-01-01

In this paper, we presented the development of a proximal soil moisture sensor that measured the soil moisture content of dairy pasture directly from the boom of an irrigator. The proposed sensor was capable of soil moisture measurements at an accuracy of  ±5% volumetric moisture content, and at meter scale ground area resolutions. The sensor adopted techniques from the ultra-wideband radar to enable measurements of ground reflection at resolutions that are smaller than the antenna beamwidth of the sensor. An experimental prototype was developed for field measurements. Extensive field measurements using the developed prototype were conducted on grass pasture at different ground conditions to validate the accuracy of the sensor in performing soil moisture measurements. (paper)

Moisture measurement in the iron and steel industry: experience with nuclear moisture measurements in coke, and studies of infrared moisture measurement of iron ore mixtures

International Nuclear Information System (INIS)

Beumer, J.A.; Wouters, M.

1976-01-01

In the heavy iron-making industry there are several processes for which it is necessary to measure on-line the moisture content of certain process materials, especially in the field of iron ore preparation and blast furnace practice. Two examples are given. (1) Experience with nuclear moisture-measurements in coke covers a period of ten years in which eight measuring systems have been installed in the weighing hoppers of blast furnaces. The standard deviation is about 0.7% moisture in the range 0 to 15% moisture. The way the method is used, the safety measures and the difficulties encountered, especially the effect on recalibration of neutron-absorbing materials in photomultipliers are described. (2) The application of infrared absorption to the study of moisture measurment or iron ore mixtures is described. With an ore mixture for pellets manufacture, a rather dark ore mixture, problems have arisen concerning the sensitivity. The reference and measuring wavelengths now in use are 2.51 and 2.95 μm. In this case the absorption of the energy is rather high. The results may be improved by using quartz optics instead of the normal Pyrex ones, as the cut-off wavelength of Pyrex is about 3 μm. Variations due to colour and specific surface have been studied. As the accuracy required is +- 0.1% moisture in the range 8 to 12% moisture, these variations need to be eliminated. (author)

Overview of OWI waste/rock interaction studies

International Nuclear Information System (INIS)

Jenks, G.H.

1977-01-01

A review is presented of office of waste isolation (OWI) programs which fall within the waste/rock categories. Discussions are included on salt repository design, thermal powers and radiation intensities, maximum temperatures and gamma doses, salt temperatures around high level waste cannisters, projects concerned with radiation and thermal effects, projects concerned with long term interactions, and waste isolation safety assessment tasks

Development of a neutron moisture gauge

International Nuclear Information System (INIS)

Prasad, A.S.

1979-01-01

A neutron moisture gauge fabricated for measuring the moisture content of coke is described. It has an americium-beryllium source placed beside a boron coated neutron counter which is a slow neutron detector. The fast neutrons emitted by the radioactive source are slowed down by the hydrogen nuclei present in the material either as bound hydrogen or as a hydrogen of the water. Measure of the slowed down i.e. thermal neutrons (their density) is proportional to the total hydrogen content of the material. The instrument is installed as an ''on-line'' measuring device to estimate the moisture content of coke at the weighing hopper feeding the skip car. The accuracy of measurement is dependent on the moisture content, i.e. higher accuracy is obtained for higher moisture content. At low moisture content, the effect of the bound hydrogen other than that of the water on low moisture readings is pronounced. Effect of bulk density on the accuracy of measurement is not very significant as long as the coke size is constant. The error is in the range of +- 1.1%. (M.G.B.)

Field lysimeter facility for evaluating the performance of commercial solidified low-level waste

International Nuclear Information System (INIS)

Walter, M.B.; Graham, M.J.; Gee, G.W.

1984-11-01

Analyzing the potential migration of radionuclides from sites containing solid low-level wastes requires knowledge of contaminant concentrations in the soil solution surrounding the waste. This soil solution concentration is generally referred to as the source term and is determined by such factors as the concentration of radionuclides in the solid waste, the rate of leachate formation, the concentration of dissolved species in the leachate, any solubility reactions occurring when the leachate contacts the soil, and the rate of water flow in the soil surrounding the waste. A field lysimeter facility established at the Hanford site is being used to determine typical source terms in arid climates for commercial low-level wastes solidifed with cement, Dow polymer (vinyl ester-styrene), and bitumen. The field lysimeter facility consists of 10, 3-m-deep by 1.8-m-dia closed-bottom lysimeters situated around a 4-m-deep by 4-m-dia central instrument caisson. Commercial cement and Dow polymer waste samples were removed from 210-L drums and placed in 8 of the lysimeters. Two bitumen samples are planned to be emplaced in the facility's remaining 2 lysimeters during 1984. The central caisson provides access to the instrumentation in the individual lysimeters and allows selective sampling of the soil and waste. Suction candles (ceramic cups) placed around the waste forms will be used to periodically collect soil-water samples for chemical analysis. Meteorological data, soil moisture content, and soil temperature are automatically monitored at the facility. Characterization of the soils and waste forms have been partially completed. These data consist of moisture release characteristics, particle-size distribution, and distributions and concentrations of radionuclides in the waste forms. 11 references, 12 figures, 5 tables

Design and optimization of automotive thermoelectric generators for maximum fuel efficiency improvement

International Nuclear Information System (INIS)

Kempf, Nicholas; Zhang, Yanliang

2016-01-01

Highlights: • A three-dimensional automotive thermoelectric generator (TEG) model is developed. • Heat exchanger design and TEG configuration are optimized for maximum fuel efficiency increase. • Heat exchanger conductivity has a strong influence on maximum fuel efficiency increase. • TEG aspect ratio and fin height increase with heat exchanger thermal conductivity. • A 2.5% fuel efficiency increase is attainable with nanostructured half-Heusler modules. - Abstract: Automotive fuel efficiency can be increased by thermoelectric power generation using exhaust waste heat. A high-temperature thermoelectric generator (TEG) that converts engine exhaust waste heat into electricity is simulated based on a light-duty passenger vehicle with a 4-cylinder gasoline engine. Strategies to optimize TEG configuration and heat exchanger design for maximum fuel efficiency improvement are provided. Through comparison of stainless steel and silicon carbide heat exchangers, it is found that both the optimal TEG design and the maximum fuel efficiency increase are highly dependent on the thermal conductivity of the heat exchanger material. Significantly higher fuel efficiency increase can be obtained using silicon carbide heat exchangers at taller fins and a longer TEG along the exhaust flow direction when compared to stainless steel heat exchangers. Accounting for major parasitic losses, a maximum fuel efficiency increase of 2.5% is achievable using newly developed nanostructured bulk half-Heusler thermoelectric modules.

Pore-scale investigation on the response of heterotrophic respiration to moisture conditions in heterogeneous soils

Energy Technology Data Exchange (ETDEWEB)

Yan, Zhifeng; Liu, Chongxuan; Todd-Brown, Katherine E.; Liu, Yuanyuan; Bond-Lamberty, Ben; Bailey, Vanessa L.

2016-11-15

The relationship between microbial respiration rate and soil moisture content is an important property for understanding and predicting soil organic carbon degradation, CO₂ production and emission, and their subsequent effects on climate change. This paper reports a pore-scale modeling study to investigate the response of heterotrophic respiration to moisture conditions in soils and to evaluate various factors that affect this response. X-ray computed tomography was used to derive soil pore structures, which were then used for pore-scale model investigation. The pore-scale results were then averaged to calculate the effective respiration rates as a function of water content in soils. The calculated effective respiration rate first increases and then decreases with increasing soil water content, showing a maximum respiration rate at water saturation degree of 0.75 that is consistent with field and laboratory observations. The relationship between the respiration rate and moisture content is affected by various factors, including pore-scale organic carbon bioavailability, the rate of oxygen delivery, soil pore structure and physical heterogeneity, soil clay content, and microbial drought resistivity. Simulations also illustrates that a larger fraction of CO₂ produced from microbial respiration can be accumulated inside soil cores under higher saturation conditions, implying that CO₂ flux measured on the top of soil cores may underestimate or overestimate true soil respiration rates under dynamic moisture conditions. Overall, this study provides mechanistic insights into the soil respiration response to the change in moisture conditions, and reveals a complex relationship between heterotrophic microbial respiration rate and moisture content in soils that is affected by various hydrological, geochemical, and biophysical factors.

Multilayer moisture barrier

Science.gov (United States)

Pankow, Joel W; Jorgensen, Gary J; Terwilliger, Kent M; Glick, Stephen H; Isomaki, Nora; Harkonen, Kari; Turkulainen, Tommy

2015-04-21

A moisture barrier, device or product having a moisture barrier or a method of fabricating a moisture barrier having at least a polymer layer, and interfacial layer, and a barrier layer. The polymer layer may be fabricated from any suitable polymer including, but not limited to, fluoropolymers such as polyethylene terephthalate (PET) or polyethylene naphthalate (PEN), or ethylene-tetrafluoroethylene (ETFE). The interfacial layer may be formed by atomic layer deposition (ALD). In embodiments featuring an ALD interfacial layer, the deposited interfacial substance may be, but is not limited to, Al.sub.2O.sub.3, AlSiO.sub.x, TiO.sub.2, and an Al.sub.2O.sub.3/TiO.sub.2 laminate. The barrier layer associated with the interfacial layer may be deposited by plasma enhanced chemical vapor deposition (PECVD). The barrier layer may be a SiO.sub.xN.sub.y film.

Contributions of Precipitation and Soil Moisture Observations to the Skill of Soil Moisture Estimates in a Land Data Assimilation System

Science.gov (United States)

Reichle, Rolf H.; Liu, Qing; Bindlish, Rajat; Cosh, Michael H.; Crow, Wade T.; deJeu, Richard; DeLannoy, Gabrielle J. M.; Huffman, George J.; Jackson, Thomas J.

2011-01-01

The contributions of precipitation and soil moisture observations to the skill of soil moisture estimates from a land data assimilation system are assessed. Relative to baseline estimates from the Modern Era Retrospective-analysis for Research and Applications (MERRA), the study investigates soil moisture skill derived from (i) model forcing corrections based on large-scale, gauge- and satellite-based precipitation observations and (ii) assimilation of surface soil moisture retrievals from the Advanced Microwave Scanning Radiometer for the Earth Observing System (AMSR-E). Soil moisture skill is measured against in situ observations in the continental United States at 44 single-profile sites within the Soil Climate Analysis Network (SCAN) for which skillful AMSR-E retrievals are available and at four CalVal watersheds with high-quality distributed sensor networks that measure soil moisture at the scale of land model and satellite estimates. The average skill (in terms of the anomaly time series correlation coefficient R) of AMSR-E retrievals is R=0.39 versus SCAN and R=0.53 versus CalVal measurements. The skill of MERRA surface and root-zone soil moisture is R=0.42 and R=0.46, respectively, versus SCAN measurements, and MERRA surface moisture skill is R=0.56 versus CalVal measurements. Adding information from either precipitation observations or soil moisture retrievals increases surface soil moisture skill levels by IDDeltaR=0.06-0.08, and root zone soil moisture skill levels by DeltaR=0.05-0.07. Adding information from both sources increases surface soil moisture skill levels by DeltaR=0.13, and root zone soil moisture skill by DeltaR=0.11, demonstrating that precipitation corrections and assimilation of satellite soil moisture retrievals contribute similar and largely independent amounts of information.

Absolute moisture sensing for cotton bales

Science.gov (United States)

With the recent prevalence of moisture restoration systems in cotton gins, more and more gins are putting moisture back into the bales immediately before the packaging operation. There are two main reasons for this recent trend, the first is that it has been found that added moisture at the bale pre...

Biomethanation of banana peel and pineapple waste

Energy Technology Data Exchange (ETDEWEB)

Bardiya, N.; Somayaji, D.; Khanna, S. [Tata Energy Research Inst., New Delhi (India)

1997-10-01

Biomethanation of banana peel and pineapple wastes studied at various HRTs showed a higher rate of gas production at lower retention time. The lowest possible HRT for banana peel was 25 days, resulting in a maximum rate of gas production of 0.76 vol/vol/day with 36% substrate utilization, while pineapple-processing waste digesters could be operated at 10 days HRT, with a maximum rate of gas production of 0.93 vol/vol/day and 58% substrate utilization. For pineapple-processing waste lowering of retention time did not affect the methane content significantly; however, with banana peel an HRT below 25 days showed a drastic reduction in methane content. (author)

Quantification of regional leachate variance from municipal solid waste landfills in China

DEFF Research Database (Denmark)

Yang, Na; Damgaard, Anders; Kjeldsen, Peter

2015-01-01

The quantity of leachate is crucial when assessing pollution emanating from municipal landfills. In most cases, existing leachate quantification measures only take into account one source - precipitation, which resulted in serious underestimation in China due to its waste properties: high moisture...... contents. To overcome this problem, a new estimation method was established considering two sources: (1) precipitation infiltrated throughout waste layers, which was simulated with the HELP model, (2) water squeezed out of the waste itself, which was theoretically calculated using actual data of Chinese...... waste. The two sources depended on climate conditions and waste characteristics, respectively, which both varied in different regions. In this study, 31 Chinese cities were investigated and classified into three geographic regions according to landfill leachate generation performance: northwestern China...

Bioremediation of the textile waste effluent by Chlorella vulgaris

Directory of Open Access Journals (Sweden)

Hala Yassin El-Kassas

2014-01-01

Full Text Available The microalgae biomass production from textile waste effluent is a possible solution for the environmental impact generated by the effluent discharge into water sources. The potential application of Chlorella vulgaris for bioremediation of textile waste effluent (WE was investigated using 22 Central Composite Design (CCD. This work addresses the adaptation of the microalgae C. vulgaris in textile waste effluent (WE and the study of the best dilution of the WE for maximum biomass production and for the removal of colour and Chemical Oxygen Demand (COD by this microalga. The cultivation of C. vulgaris, presented maximum cellular concentrations Cmax and maximum specific growth rates μmax in the wastewater concentration of 5.0% and 17.5%, respectively. The highest colour and COD removals occurred with 17.5% of textile waste effluent. The results of C. vulgaris culture in the textile waste effluent demonstrated the possibility of using this microalga for the colour and COD removal and for biomass production. There was a significant negative relationship between textile waste effluent concentration and Cmax at 0.05 level of significance. However, sodium bicarbonate concentration did not significantly influence the responses of Cmax and the removal of colour and COD.

Appraisal of nuclear waste isolation in the vadose zone in arid and semiarid regions (with emphasis on the Nevada Test Site)

International Nuclear Information System (INIS)

Wollenberg, H.A.; Wang, J.S.Y.; Korbin, G.

1983-05-01

An appraisal was made of the concept of isolating high-level radioactive waste in the vadose zone of alluvial-filled valleys and tuffaceous rocks of the Basin and Range geomorphic province. Principal attributes of these terranes are: (1) low population density, (2) low moisture influx, (3) a deep water table, (4) the presence of sorptive rocks, and (5) relative ease of construction. Concerns about heat effects of waste on unsaturated rocks of relatively low thermal conductivity are considered. Calculations show that a standard 2000-acre repository with a thermal loading of 40 kW/acre in partially saturated alluvium or tuff would experience an average temperature rise of less than 100 0 C above the initial temperature. The actual maximum temperature would depend strongly on the emplacement geometry. Concerns about seismicity, volcanism, and future climatic change are also mitigated. The conclusion reached in this appraisal is that unsaturated zones in alluvium and tuff of arid regions should be investigated as comprehensively as other geologic settings considered to be potential repository sites

Appraisal of nuclear waste isolation in the vadose zone in arid and semiarid regions (with emphasis on the Nevada Test Site)

Energy Technology Data Exchange (ETDEWEB)

Wollenberg, H.A.; Wang, J.S.Y.; Korbin, G.

1983-05-01

An appraisal was made of the concept of isolating high-level radioactive waste in the vadose zone of alluvial-filled valleys and tuffaceous rocks of the Basin and Range geomorphic province. Principal attributes of these terranes are: (1) low population density, (2) low moisture influx, (3) a deep water table, (4) the presence of sorptive rocks, and (5) relative ease of construction. Concerns about heat effects of waste on unsaturated rocks of relatively low thermal conductivity are considered. Calculations show that a standard 2000-acre repository with a thermal loading of 40 kW/acre in partially saturated alluvium or tuff would experience an average temperature rise of less than 100{sup 0}C above the initial temperature. The actual maximum temperature would depend strongly on the emplacement geometry. Concerns about seismicity, volcanism, and future climatic change are also mitigated. The conclusion reached in this appraisal is that unsaturated zones in alluvium and tuff of arid regions should be investigated as comprehensively as other geologic settings considered to be potential repository sites.

Parametrization of the increase of the aeolian erosion threshold wind friction velocity due to soil moisture for arid and semi-arid areas

Directory of Open Access Journals (Sweden)

F. Fécan

1999-01-01

Full Text Available Large-scale simulation of the soil-derived dust emission in semi-arid regions needs to account for the influence of the soil moisture on the wind erosion threshold. Soil water retention consists of molecular adsorption on the soil grain surface and capillary forces between the grain. Interparticle capillary forces (characterized by the moisture tension are the main factor responsible for the increase of the wind erosion threshold observed when the soil moisture increases. When the soil moisture content is close to but smaller than the maximum amount of adsorbed water, w' (depending on the soil texture, these capillary forces are considered as not strong enough to significantly increase the erosion threshold. An expression of the moisture tension as a function of soil moisture and w' is derived from retention curves. From this expression, a parametrization of the ratio of the wet to dry erosion thresholds has been developed as a function of soil moisture and soil texture. The coefficients of this parametrization have been determined by using experimental data from the literature. An empirical relationship between w' and soil clay content has been established. The erosion threshold ratios simulated for different soil textures were found to be in good agreement with the experimental data.Key words. Atmospheric composition and structure (Aerosols and particles · Hydrology (soil moisture

MOISTURE-BUFFERING CHARACTERISTICS OF BUILDING MATERIALS

Directory of Open Access Journals (Sweden)

Young Cheol Choi

2016-05-01

Full Text Available The humidity level of indoor air is an important factor influencing the air quality and energy consumption of buildings, as well as the durability of building components. Indoor humidity levels depend on several factors, such as moisture sources, air flow, and the adsorption/desorption properties of materials. The moisture-buffering characteristics of building materials that are in contact with indoor air may help moderate the variations of indoor humidity, especially in the summer and winter. In this study, the moisture adsorption/desorption properties of building materials were investigated experimentally and numerically. These properties can be used to characterize the ability of building materials to exchange moisture with the indoor environment. This study indicates that a building material surface resistivity was the main factor creating variations of moisture buffering.

Role of low seed moisture in increasing the effectiveness of gamma rays for plant type and grain quality mutations in wheat, tritium aestivum var k-68

International Nuclear Information System (INIS)

Kumar, Devendra; Singh, R.M.

1975-01-01

Seeds of the wheat variety K-68 equilibrated at 14 and 4% moisture levels were irradiated with 5,10,15, and 20Kr doses of Co 60 gamma rays. The observations in M 1 generation on germination, survival, seedling height, chromosomal aberrations and pollen and ovule sterility indicated maximum radiosensitivity at 4% seed moisture level with increasing doses. Further, in M 2 generation both mutation frequency and spectrum were much greater at 4% seed moisture level. Desirable mutants from yield point of view were identified in M 2 and stabilized in M 3 generation. Five promising mutants, out of which three were from 4% seed moisture level, along with control were grown in a randomized block design in M 4 generation. Mutant HUW-Dfl yielded highest (29.30q/ha) and HUW-DrHP3 the lowest (18.50q/ha), the control yield being 18.70q/ha. Protein values ranged from 12.57 to 16.76% for different mutants as against 12.92% for control. Mutant HUW-SDf2 had the highest lysine value (2.81%) and HYW-DfHP2 the lowest value (2.21%). There was a significant negative correlation (rsup(=)-.961) between protein and lysine. Pelsenke value ranged from 39 to 246 (min.) for different mutants in contrast to 198 (min.) for control, giving a fairly good latitude for biscuit, bread, and chapati making purposes. Findings clearly indicate that seed moisture greatly influences gamma rays induced mutations which may be attributed to maximum accumulation of long lived free radicals at 4% moisture level. (author)

Assessment of geomechanical properties, maximum depth and excavation damaged zone aspects - Expert report

International Nuclear Information System (INIS)

Amann, F.; Löw, S.; Perras, M.

2015-11-01

This comprehensive report published by the Swiss National Nuclear Safety Inspectorate ENSI discusses the expert report published on the need for the assessment of geomechanical properties and maximum depth of repositories for high, medium and low-activity nuclear wastes. Also, aspects concerning excavation damaged zones (EDZ) are considered. These are all criteria for the selection of sites as part of Phase 2 of the Swiss waste disposal project. Four questions are examined: are NAGRA’s documented basic considerations and calculations on Opalinus Clay comprehensive enough and correct, are the calculations on maximum depth correct, are the proposed storage perimeters correct with respect to depth and will NAGRA be able to take possible excavation damaged zones (EDZ) into account? Literature and references concerning the subject are quoted

Interior moisture design loads for residences

Science.gov (United States)

Anton TenWolde; Iain S. Walker

2001-01-01

This paper outlines a methodology to obtain design values for indoor boundary conditions for moisture design calculations for residences. This is part of a larger effort by ASHRAE Standard Project Committee 160P, Design Criteria for Moisture Control in Buildings, to formulate criteria for moisture design loads, analysis techniques, and material and building performance...

Centralized collection of radioactive wastes

International Nuclear Information System (INIS)

1985-06-01

The standard based upon TGL-190-921/03 applies to solid wastes of the category A2 and the radiation protection groups S3, S4 and S5. The following items are specified: (1) requirements concerning the form and properties of the waste (permitted composition, unpermitted components, type of packaging, maximum weight per package/container), (2) technical conditions for connecting technical means of collection (lifting devices, traffic connections) with customer, and (3) tasks in handing/taking over the waste in relation to waste type (controls, operation of facilities, decontamination, transport documents)

Centralized collection of radioactive wastes

International Nuclear Information System (INIS)

1985-06-01

The standard based upon TGL-190-921/02 applies to solid wastes of the category A1 and the radiation protection groups S1 and S2. The following items are specified: (1) requirements concerning the form and properties of the waste (permitted composition, unpermitted components, type of packaging, maximum weight per package/container), (2) technical conditions for connecting technical means of collection (lifting devices, traffic connections) with customer, and (3) tasks in handing/taking over the waste in relation to waste type (controls, operation of facilities, decontamination, transport documents)

Australian Soil Moisture Field Experiments in Support of Soil Moisture Satellite Observations

Science.gov (United States)

Kim, Edward; Walker, Jeff; Rudiger, Christopher; Panciera, Rocco

2010-01-01

Large-scale field campaigns provide the critical fink between our understanding retrieval algorithms developed at the point scale, and algorithms suitable for satellite applications at vastly larger pixel scales. Retrievals of land parameters must deal with the substantial sub-pixel heterogeneity that is present in most regions. This is particularly the case for soil moisture remote sensing, because of the long microwave wavelengths (L-band) that are optimal. Yet, airborne L-band imagers have generally been large, heavy, and required heavy-lift aircraft resources that are expensive and difficult to schedule. Indeed, US soil moisture campaigns, have been constrained by these factors, and European campaigns have used non-imagers due to instrument and aircraft size constraints. Despite these factors, these campaigns established that large-scale soil moisture remote sensing was possible, laying the groundwork for satellite missions. Starting in 2005, a series of airborne field campaigns have been conducted in Australia: to improve our understanding of soil moisture remote sensing at large scales over heterogeneous areas. These field data have been used to test and refine retrieval algorithms for soil moisture satellite missions, and most recently with the launch of the European Space Agency's Soil Moisture Ocean Salinity (SMOS) mission, to provide validation measurements over a multi-pixel area. The campaigns to date have included a preparatory campaign in 2005, two National Airborne Field Experiments (NAFE), (2005 and 2006), two campaigns to the Simpson Desert (2008 and 2009), and one Australian Airborne Cal/val Experiment for SMOS (AACES), just concluded in the austral spring of 2010. The primary airborne sensor for each campaign has been the Polarimetric L-band Microwave Radiometer (PLMR), a 6-beam pushbroom imager that is small enough to be compatible with light aircraft, greatly facilitating the execution of the series of campaigns, and a key to their success. An

Water and waste water reclamation in a 21st century space colony

Science.gov (United States)

Jebens, H. J.; Johnson, R. D.

1977-01-01

The paper presents the results of research on closed-life support systems initiated during a system design study on space colonization and concentrates on the water and waste water components. Metabolic requirements for the 10,000 inhabitants were supplied by an assumed earth-like diet from an intensive agriculture system. Condensed atmospheric moisture provided a source of potable water and a portion of the irrigation water. Waste water was reclaimed by wet oxidation. The dual-water supply required the condensation of 175 kg/person-day of atmospheric water and the processing of 250 kg/person-day of waste water.

Gelatinous soil barrier for reducing contaminant emissions at waste-disposal sites

International Nuclear Information System (INIS)

Opitz, B.E.; Martin, W.J.; Sherwood, D.R.

1982-09-01

The milling of uranium ore produces large quantities of waste (mill tailings) that are being deposited in earthen pits or repositories. These wastes, which remain potentially hazardous for long time periods, may reach the biosphere at levels greater than those allowed by the Environmental Protection Agency (EPA). For example, the leachates associated with these wastes contain numerous radionuclides and toxic trace metals at levels 10 2 to 10 4 greater than allowable for drinking water based on EPA Primary Drinking Water Standards. As a result, technologies must be developed to ensure that such wastes will not reach the biosphere at hazardous levels. Under sponsorship of the Department of Energy's Uranium Mill Tailings Remedial Action Program (UMTRAP), Pacific Northwest Laboratory (PNL) has investigated the use of engineered barriers for use as liners and covers for waste containment. Results of these investigations have led to the development of a low permeable, multilayer earthen barrier that effectively reduces contaminant loss from waste disposal sites. The multilayer earth barrier was developed as an alternative to clay liner or cover schemes for use in areas where clays were not locally available and must be shipped to the disposal site. The barrier layer is comprised of 90% locally available materials whose liner or cover properties are enhanced by the addition of a gelatinous precipitate which entrains moisture into the cover's air-filled pore spaces, blocking the pathways through which gas would otherwise diffuse into the atmosphere or through which moisture would migrate into the ground. In field verification tests, the earthen seal reduced radon gas emissions by 95 to 99% over prior release rates with measured permeabilities on the order of 10 - 9 cm/s

Effectiveness of modified 1-hour air-oven moisture methods for determining popcorn moisture

Science.gov (United States)

Two of the most commonly used approved grain moisture air-oven reference methods are the air oven method ASAE S352.2, which requires long heating time (72-h) for unground samples, and the AACC 44-15.02 air-oven method, which dries a ground sample for 1 hr, but there is specific moisture measurement ...

Digital radioisotope moisture-density meter

International Nuclear Information System (INIS)

Bychvarov, N.; Vankov, I.; Dimitrov, L.

1982-01-01

The primary information from the detectors of a combined radioisotope moisture-density meter is obtained as pulses, their counting rate being functionally dependent on the humidity per unit volume and the wet density. However, most practical cases demand information on the moisture per unit weight and the mass density of the dry skeleton. The paper describes how the proposed electronic circuit processes the input primary information to obtain the moisture in weight % and the mass density of the dry skeleton in g/cm 3 . (authors)

High-level waste leakage from the 241-T-106 tank at Hanford

International Nuclear Information System (INIS)

Routson, R.C.; Price, W.H.; Brown, D.J.; Fecht, K.R.

1979-02-01

The history, status, fate, and impact of the 4.34 x 10 5 -liter (115,000-gal) radioactive waste tank leak from the 241-T-106 tank have been studied since 1973. As of May 1978, the maximum detected depth of the 1-microcurie per liter (μCi/l) concentration of 106 Ru penetration was 33 meters (108 ft) below the ground surface or 29 meters (95 ft) above the regional water table. This maximum depth of penetration was detected in two of the dry wells in the 241-T tank farm. In no other well has radioactivity greater than 1.0-μCi/l been found deeper than 29 meters (95 ft). This is approximately 43% of the distance from the bottom of the tank to the water table. The maximum horizontal movement of the 1-μCi/l 106 Ru concentration front from the tank was approximately 23 meters (75 ft) at a depth of 25 meters (82 ft). This distance is approximately equal to the diameter of the tank. The rate of frontal movement of radioactivity was qualitatively estimated. A large portion of the movement occurred in 1973, prior to the publication of an initial tank leak status report. From 1973 to 1974, detectable lateral movement occurred in at least some sediment layers. From 1974 to 1978, movement could not generally be detected. However, migration in wells near the leak perimeter was detected in 1978, and the probable cause defined. Calculations on vadose zone moisture and wetting frontal movement were found to be essentially in qualitative agreement in their assessed lack of movement of any waste above concentration guidelines to the Hanford ground water. Thus, during the hazardous lifetime of the fission products, there will likely be no amount of radioactivity enter the Hanford ground water. Therefore, there appears to be no impact of the leak on the Columbia River

Modeling soil moisture memory in savanna ecosystems

Science.gov (United States)

Gou, S.; Miller, G. R.

2011-12-01

Antecedent soil conditions create an ecosystem's "memory" of past rainfall events. Such soil moisture memory effects may be observed over a range of timescales, from daily to yearly, and lead to feedbacks between hydrological and ecosystem processes. In this study, we modeled the soil moisture memory effect on savanna ecosystems in California, Arizona, and Africa, using a system dynamics model created to simulate the ecohydrological processes at the plot-scale. The model was carefully calibrated using soil moisture and evapotranspiration data collected at three study sites. The model was then used to simulate scenarios with various initial soil moisture conditions and antecedent precipitation regimes, in order to study the soil moisture memory effects on the evapotranspiration of understory and overstory species. Based on the model results, soil texture and antecedent precipitation regime impact the redistribution of water within soil layers, potentially causing deeper soil layers to influence the ecosystem for a longer time. Of all the study areas modeled, soil moisture memory of California savanna ecosystem site is replenished and dries out most rapidly. Thus soil moisture memory could not maintain the high rate evapotranspiration for more than a few days without incoming rainfall event. On the contrary, soil moisture memory of Arizona savanna ecosystem site lasts the longest time. The plants with different root depths respond to different memory effects; shallow-rooted species mainly respond to the soil moisture memory in the shallow soil. The growing season of grass is largely depended on the soil moisture memory of the top 25cm soil layer. Grass transpiration is sensitive to the antecedent precipitation events within daily to weekly timescale. Deep-rooted plants have different responses since these species can access to the deeper soil moisture memory with longer time duration Soil moisture memory does not have obvious impacts on the phenology of woody plants

Lawrence Livermore National Laboratory low-level waste systems performance assessment

International Nuclear Information System (INIS)

1990-11-01

This Low-Level Radioactive Waste (LLW) Systems Performance Assessment (PA) presents a systematic analysis of the potential risks posed by the Lawrence Livermore National Laboratory (LLNL) waste management system. Potential risks to the public and environment are compared to established performance objectives as required by DOE Order 5820.2A. The report determines the associated maximum individual committed effective dose equivalent (CEDE) to a member of the public from LLW and mixed waste. A maximum annual CEDE of 0.01 mrem could result from routine radioactive liquid effluents. A maximum annual CEDE of 0.003 mrem could result from routine radioactive gaseous effluents. No other pathways for radiation exposure of the public indicated detectable levels of exposure. The dose rate, monitoring, and waste acceptance performance objectives were found to be adequately addressed by the LLNL Program. 88 refs., 3 figs., 17 tabs

Changes in soil hydraulic properties caused by construction of a simulated waste trench at the Idaho National Engineering Laboratory, Idaho

International Nuclear Information System (INIS)

Shakofsky, S.

1995-03-01

In order to assess the effect of filled waste disposal trenches on transport-governing soil properties, comparisons were made between profiles of undisturbed soil and disturbed soil in a simulated waste trench. The changes in soil properties induced by the construction of a simulated waste trench were measured near the Radioactive Waste Management Complex at the Idaho National Engineering Laboratory (INEL) in the semiarid southeast region of Idaho. The soil samples were collected, using a hydraulically-driven sampler to minimize sample disruption, from both a simulated waste trench and an undisturbed area nearby. Results show that the undisturbed profile has distinct layers whose properties differ significantly, whereas the soil profile in the simulated waste trench is, by comparison, homogeneous. Porosity was increased in the disturbed cores, and, correspondingly, saturated hydraulic conductivities were on average three times higher. With higher soil-moisture contents (greater than 0.32), unsaturated hydraulic conductivities for the undisturbed cores were typically greater than those for the disturbed cores. With lower moisture contents, most of the disturbed cores had greater hydraulic conductivities. The observed differences in hydraulic conductivities are interpreted and discussed as changes in the soil pore geometry

Estimating the responses of winter wheat yields to moisture variations in the past 35 years in Jiangsu Province of China.

Science.gov (United States)

Xu, Xiangying; Gao, Ping; Zhu, Xinkai; Guo, Wenshan; Ding, Jinfeng; Li, Chunyan

2018-01-01

Jiangsu is an important agricultural province in China. Winter wheat, as the second major grain crop in the province, is greatly affected by moisture variations. The objective of this study was to investigate whether there were significant trends in changes in the moisture conditions during wheat growing seasons over the past decades and how the wheat yields responded to different moisture levels by means of a popular drought index, the Standardized Precipitation Evapotranspiration Index (SPEI). The study started with a trend analysis and quantification of the moisture conditions with the Mann-Kendall test and Sen's Slope method, respectively. Then, correlation analysis was carried out to determine the relationship between de-trended wheat yields and multi-scalar SPEI. Finally, a multivariate panel regression model was established to reveal the quantitative yield responses to moisture variations. The results showed that the moisture conditions in Jiangsu were generally at a normal level, but this century appeared slightly drier in because of the relatively high temperatures. There was a significant correlation between short time scale SPEI values and wheat yields. Among the three critical stages of wheat development, the SPEI values in the late growth stage (April-June) had a closer linkage to the yields than in the seedling stage (October-November) and the over-wintering stage (December-February). Moreover, the yield responses displayed an asymmetric characteristic, namely, moisture excess led to higher yield losses compared to moisture deficit in this region. The maximum yield increment could be obtained under the moisture level of slight drought according to the 3-month SPEI at the late growth stage, while extreme wetting resulted in the most severe yield losses. The moisture conditions in the first 15 years of the 21st century were more favorable than in the last 20 years of the 20th century for wheat production in Jiangsu.

Estimating the responses of winter wheat yields to moisture variations in the past 35 years in Jiangsu Province of China.

Directory of Open Access Journals (Sweden)

Xiangying Xu

Full Text Available Jiangsu is an important agricultural province in China. Winter wheat, as the second major grain crop in the province, is greatly affected by moisture variations. The objective of this study was to investigate whether there were significant trends in changes in the moisture conditions during wheat growing seasons over the past decades and how the wheat yields responded to different moisture levels by means of a popular drought index, the Standardized Precipitation Evapotranspiration Index (SPEI. The study started with a trend analysis and quantification of the moisture conditions with the Mann-Kendall test and Sen's Slope method, respectively. Then, correlation analysis was carried out to determine the relationship between de-trended wheat yields and multi-scalar SPEI. Finally, a multivariate panel regression model was established to reveal the quantitative yield responses to moisture variations. The results showed that the moisture conditions in Jiangsu were generally at a normal level, but this century appeared slightly drier in because of the relatively high temperatures. There was a significant correlation between short time scale SPEI values and wheat yields. Among the three critical stages of wheat development, the SPEI values in the late growth stage (April-June had a closer linkage to the yields than in the seedling stage (October-November and the over-wintering stage (December-February. Moreover, the yield responses displayed an asymmetric characteristic, namely, moisture excess led to higher yield losses compared to moisture deficit in this region. The maximum yield increment could be obtained under the moisture level of slight drought according to the 3-month SPEI at the late growth stage, while extreme wetting resulted in the most severe yield losses. The moisture conditions in the first 15 years of the 21st century were more favorable than in the last 20 years of the 20th century for wheat production in Jiangsu.

Integrated Solid Waste Management for Urban Area in Basrah District

Directory of Open Access Journals (Sweden)

Abdulhussain Abdul Kareem Abbas

2016-09-01

Full Text Available The success of waste management requires accurate data on generation and composition of waste which is pivotal for the decisions towards the appropriate waste management system. A five years (2008-2012 study was conducted to evaluate the solid wastes management system in all the six divisions of Basrah district (more than 30 sub-districts. Recent investigations in 2012 resulted information that population of Basrah district has reached 1,018,000 person The quantity of municipal solid waste generated was recorded to be 634 tons per day with MSW generation rates of 0.62 kg per capita per day. Municipal solid waste density was conducted as 192.6 kg/m³ with moisture content of 31.1%. The main components of the MSW were Food wastes represents largest proportion (54.8%, followed by plastic (25.2% and paper (7%. The study results reveal that the MSW stream has the largest proportion of biodegradable and recyclable waste. Therefore, the study recommends to use methods of waste treatment such composting, recycling and incineration in order to reduce the amount of waste that are taken to the landfill.

Extraction of soil solution by drainage centrifugation-effects of centrifugal force and time of centrifugation on soil moisture recovery and solute concentration in soil moisture of loess subsoils.

Science.gov (United States)

Fraters, Dico; Boom, Gerard J F L; Boumans, Leo J M; de Weerd, Henk; Wolters, Monique

2017-02-01

The solute concentration in the subsoil beneath the root zone is an important parameter for leaching assessment. Drainage centrifugation is considered a simple and straightforward method of determining soil solution chemistry. Although several studies have been carried out to determine whether this method is robust, hardly any results are available for loess subsoils. To study the effect of centrifugation conditions on soil moisture recovery and solute concentration, we sampled the subsoil (1.5-3.0 m depth) at commercial farms in the loess region of the Netherlands. The effect of time (20, 35, 60, 120 and 240 min) on recovery was studied at two levels of the relative centrifugal force (733 and 6597g). The effect of force on recovery was studied by centrifugation for 35 min at 117, 264, 733, 2932, 6597 and 14,191g. All soil moisture samples were chemically analysed. This study shows that drainage centrifugation offers a robust, reproducible and standardised way for determining solute concentrations in mobile soil moisture in silt loam subsoils. The centrifugal force, rather than centrifugation time, has a major effect on recovery. The maximum recovery for silt loams at field capacity is about 40%. Concentrations of most solutes are fairly constant with an increasing recovery, as most solutes, including nitrate, did not show a change in concentration with an increasing recovery.

Assimilation of Remotely Sensed Soil Moisture Profiles into a Crop Modeling Framework for Reliable Yield Estimations

Science.gov (United States)

Mishra, V.; Cruise, J.; Mecikalski, J. R.

2017-12-01

Much effort has been expended recently on the assimilation of remotely sensed soil moisture into operational land surface models (LSM). These efforts have normally been focused on the use of data derived from the microwave bands and results have often shown that improvements to model simulations have been limited due to the fact that microwave signals only penetrate the top 2-5 cm of the soil surface. It is possible that model simulations could be further improved through the introduction of geostationary satellite thermal infrared (TIR) based root zone soil moisture in addition to the microwave deduced surface estimates. In this study, root zone soil moisture estimates from the TIR based Atmospheric Land Exchange Inverse (ALEXI) model were merged with NASA Soil Moisture Active Passive (SMAP) based surface estimates through the application of informational entropy. Entropy can be used to characterize the movement of moisture within the vadose zone and accounts for both advection and diffusion processes. The Principle of Maximum Entropy (POME) can be used to derive complete soil moisture profiles and, fortuitously, only requires a surface boundary condition as well as the overall mean moisture content of the soil column. A lower boundary can be considered a soil parameter or obtained from the LSM itself. In this study, SMAP provided the surface boundary while ALEXI supplied the mean and the entropy integral was used to tie the two together and produce the vertical profile. However, prior to the merging, the coarse resolution (9 km) SMAP data were downscaled to the finer resolution (4.7 km) ALEXI grid. The disaggregation scheme followed the Soil Evaporative Efficiency approach and again, all necessary inputs were available from the TIR model. The profiles were then assimilated into a standard agricultural crop model (Decision Support System for Agrotechnology, DSSAT) via the ensemble Kalman Filter. The study was conducted over the Southeastern United States for the

SMOS validation of soil moisture and ocen salinity (SMOS) soil moisture over watershed networks in the U.S.

Science.gov (United States)

Estimation of soil moisture at large scale has been performed using several satellite-based passive microwave sensors and a variety of retrieval methods. The most recent source of soil moisture is the European Space Agency Soil Moisture and Ocean Salinity (SMOS) mission. A thorough validation must b...

Isotopic evidence for climatic conditions in Southeast Asia at the last glacial maximum

International Nuclear Information System (INIS)

Aggarwal, P.K.; Gibson, J.J.; Kulkarni, K.M.; Froehlich, K.

2002-01-01

Stable isotope composition of dated groundwater archives from the Philippines, Vietnam, Thailand and Bangladesh trace changes in monsoon conditions, primarily rainout processes between the Last Glacial Maximum (LGM) and present day in southeast Asia. Today, isotope-climate relations are well established by the IAEA/WMO Global Network of Isotopes in Precipitation survey which reveals more depleted δ 18 O and δ 2 H for the Pacific Ocean monsoon regime than for the Indian Ocean monsoon regime, primarily due to proximal ocean sources and subdued continental moisture recycling for the latter region. Groundwater archives, reflecting past isotopic composition of precipitation, strongly suggest that this distinction was preserved or slightly enhanced at the time of the LGM, despite an apparent weakening of the summer monsoon and associated rainout processes. Overall, precipitation and moisture recycling, and enhanced continental effects are inferred to be the primary controls on δ 18 O signals in groundwater in southeast Asia. Comparison of groundwater isotope signatures and an ECHAM4 model simulation of the isotopic distribution in precipitation at 21ka reveal similar patterns, but the impacts of increased air mass contributions from high latitudes and reduced Eurasian moisture recycling at the LGM are shown to be potentially greater for the Pacific region than predicted by the model. (author)

Comparison of date-palm wastes and perlite as growth substrates ...

African Journals Online (AJOL)

The date palm wastes were first manually chopped into small pieces, after which they were kept in plastic bags. They were adjusted to 55% moisture content and thoroughly mixed once every week. Treatments were done for 4 incubation times (0, 1, 3 and 9 months). The physicochemical properties of materials were ...

Fundamental characteristics of input waste of small MSW incinerators in Korea.

Science.gov (United States)

Choi, Ki-In; Lee, Suk-Hui; Lee, Dong-Hoon; Osako, Masahiro

2008-11-01

Waste incineration in a small incinerator is a simple and convenient way of treating waste discharged from small areas or from large facilities and buildings such as business centers, marketplaces, factories, and military units. Despite their ostensible advantages, however, many small incinerators frequently suffer from serious problems, e.g., unsystematic waste feeding, unstable combustion, deficient air pollution control devices, and consequently, environmental pollution. To obtain a better understanding of the characterization of wastes in small incinerators, we investigated a series of fundamental characteristics, i.e., physical composition, bulk density, proximate and ultimate analysis, potential energy content, and so on. The main waste components in small incinerators were identified as paper and plastic; the proportion of food waste was less than that in large incinerators. Especially, a low ratio of food waste had a strong influence on other waste characteristics, e.g., lower moisture content and bulk density, and higher potential energy. On the other hand, in contrast with that of HCl, there was no distinguishable linear relationship between Cl content in waste and PCDD/DF concentration in combustion gas.

Single-shot LIBS spectral quality for waste particles in open air

NARCIS (Netherlands)

Xia, H.; Bakker, M.C.M.

2015-01-01

This work investigates the ability of LIBS to produce quality spectra from small particles of concrete demolition waste using single-shot spectra collected in open air. The 2–8?mm materials are rounded river gravel, green glass shards, and plastic flakes. Considered are focal length, air, moisture,

Expected brine movement at potential nuclear waste repository salt sites

International Nuclear Information System (INIS)

McCauley, V.S.; Raines, G.E.

1987-08-01

The BRINEMIG brine migration code predicts rates and quantities of brine migration to a waste package emplaced in a high-level nuclear waste repository in salt. The BRINEMIG code is an explicit time-marching finite-difference code that solves a mass balance equation and uses the Jenks equation to predict velocities of brine migration. Predictions were made for the seven potentially acceptable salt sites under consideration as locations for the first US high-level nuclear waste repository. Predicted total quantities of accumulated brine were on the order of 1 m 3 brine per waste package or less. Less brine accumulation is expected at domal salt sites because of the lower initial moisture contents relative to bedded salt sites. Less total accumulation of brine is predicted for spent fuel than for commercial high-level waste because of the lower temperatures generated by spent fuel. 11 refs., 36 figs., 29 tabs

Zero Waste and Conversion Efficiencies of Various Technologies for Disposal of Municipal Solid Waste

Institute of Scientific and Technical Information of China (English)

Zhang Wenyang

2005-01-01

Zero waste is a philosophy and a design principle of dealing with our waste stream for the 21st century. After reviewing the available information, the goal of zero waste from landfill is considered to be unachievable by using known and proven methods and approaches. The comparison of various technologies shows that the conversion efficiencies depend upon the type of system chosen for processing residual waste, and the best overall diversion rate of waste management system that can be achieved is about 71%. The maximum achievable overall diversion rate can be increased to approximate 92% if current environmental regulations to permit the routine use of the bottom ash or char for advanced thermal technologies.

Torrefaction Processing for Human Solid Waste Management

Science.gov (United States)

Serio, Michael A.; Cosgrove, Joseph E.; Wójtowicz, Marek A.; Stapleton, Thomas J.; Nalette, Tim A.; Ewert, Michael K.; Lee, Jeffrey; Fisher, John

2016-01-01

This study involved a torrefaction (mild pyrolysis) processing approach that could be used to sterilize feces and produce a stable, odor-free solid product that can be stored or recycled, and also to simultaneously recover moisture. It was demonstrated that mild heating (200-250 C) in nitrogen or air was adequate for torrefaction of a fecal simulant and an analog of human solid waste (canine feces). The net result was a nearly undetectable odor (for the canine feces), complete recovery of moisture, some additional water production, a modest reduction of the dry solid mass, and the production of small amounts of gas and liquid. The liquid product is mainly water, with a small Total Organic Carbon content. The amount of solid vs gas plus liquid products can be controlled by adjusting the torrefaction conditions (final temperature, holding time), and the current work has shown that the benefits of torrefaction could be achieved in a low temperature range (< 250 C). These temperatures are compatible with the PTFE bag materials historically used by NASA for fecal waste containment and will reduce the energy consumption of the process. The solid product was a dry material that did not support bacterial growth and was hydrophobic relative to the starting material. In the case of canine feces, the solid product was a mechanically friable material that could be easily compacted to a significantly smaller volume (approx. 50%). The proposed Torrefaction Processing Unit (TPU) would be designed to be compatible with the Universal Waste Management System (UWMS), now under development by NASA. A stand-alone TPU could be used to treat the canister from the UWMS, along with other types of wet solid wastes, with either conventional or microwave heating. Over time, a more complete integration of the TPU and the UWMS could be achieved, but will require design changes in both units.

Effect of miscibility and soil water content in movement of mixed waste

International Nuclear Information System (INIS)

Park, W.J.

1989-01-01

Since commercial low-level waste sites will not accept mixed low level wastes for disposal any longer, safer disposal of these wastes as well as hazardous waste becomes the growing concern. The objective of this study were to estimate the effect of some characteristics of organic material, such as solubility, density and volatility, on the movement in soil under various moisture contents. Attempts were made to fit the measured data to theoretical models for the movement of aqueous and airborne components through the vadose zone. Four different C-14 labeled organic materials, Methyl Alcohol, Toluene, Formic Acid, and Bromobenzene, differing in density, solubility, and volatility, were injected into test columns packed with a mixture of sands having known particles sizes and porosity. The method employed to make calibrated unsaturated conditions proved to be adequate for four different designated moisture contents, permitting sampling of both airborne and aqueous components at the same time. Significant solubility and density effects were found for the different organic materials associated with movement through water channels or air-filled pores, which became available at various unsaturated conditions. To analyze this mobility mechanism as a function of inherent properties of organic materials, a couple of mathematical equations were presented to describe both airborne release and aqueous migration and their wider applicability was discussed

Soil moisture memory at sub-monthly time scales

Science.gov (United States)

Mccoll, K. A.; Entekhabi, D.

2017-12-01

For soil moisture-climate feedbacks to occur, the soil moisture storage must have `memory' of past atmospheric anomalies. Quantifying soil moisture memory is, therefore, essential for mapping and characterizing land-atmosphere interactions globally. Most previous studies estimate soil moisture memory using metrics based on the autocorrelation function of the soil moisture time series (e.g., the e-folding autocorrelation time scale). This approach was first justified by Delworth and Manabe (1988) on the assumption that monthly soil moisture time series can be modelled as red noise. While this is a reasonable model for monthly soil moisture averages, at sub-monthly scales, the model is insufficient due to the highly non-Gaussian behavior of the precipitation forcing. Recent studies have shown that significant soil moisture-climate feedbacks appear to occur at sub-monthly time scales. Therefore, alternative metrics are required for defining and estimating soil moisture memory at these shorter time scales. In this study, we introduce metrics, based on the positive and negative increments of the soil moisture time series, that can be used to estimate soil moisture memory at sub-monthly time scales. The positive increments metric corresponds to a rapid drainage time scale. The negative increments metric represents a slower drying time scale that is most relevant to the study of land-atmosphere interactions. We show that autocorrelation-based metrics mix the two time scales, confounding physical interpretation. The new metrics are used to estimate soil moisture memory at sub-monthly scales from in-situ and satellite observations of soil moisture. Reference: Delworth, Thomas L., and Syukuro Manabe. "The Influence of Potential Evaporation on the Variabilities of Simulated Soil Wetness and Climate." Journal of Climate 1, no. 5 (May 1, 1988): 523-47. doi:10.1175/1520-0442(1988)0012.0.CO;2.

Moisture relationships in composting processes

NARCIS (Netherlands)

Richard, T.L.; Veeken, A.H.M.

2002-01-01

Moisture is a key environmental factor that affects many aspects of the composting process. Biodegradation kinetics are affected by moisture through changes in oxygen diffusion, water potential and water activity, and microbial growth rates. These relationships are made more complex by the dynamic

Assessment of methane production from shredder waste in landfills: The influence of temperature, moisture and metals

DEFF Research Database (Denmark)

Fathi Aghdam, Ehsan; Scheutz, Charlotte; Kjeldsen, Peter

2017-01-01

different temperatures (20-25°C, 37°C, and 55°C), moisture contents (35% and 75% w/w) and amounts of inoculum (5% and 30% of the samples wet weight). The biochemical methane potential (BMP) from different types of SW (fresh, old and sieved) was determined and compared. The ability of metals (iron, aluminum...

Research summary: characterization of radionuclide and moisture movement through arid region sediments

International Nuclear Information System (INIS)

Gee, G.W.; Jones, T.L.; Rai, D.

1981-09-01

This project has the task of understanding the movement of moisture and radionuclides under arid region conditions. This understanding will be used to maximize the isolation of low level waste from the environment. Specific objectives include: field monitoring of moisture and radionuclide transport at an arid region site; assessment of the interaction of radionuclides with unsaturated soils in arid regions; evaluation of radionuclide transport in unsaturated soils by appropriate mathematical models; and assessment of the importance of upward migration of radionuclides by evaporation and diffusion processes. The Burial Waste Test Facility (BWTF) located near Richland, Washington, on the Department of Energy (DOE) Hanford Site has been monitored for water content and radionuclide transport for the past two years. Tritium movement has been observed to depths of 7.6 m in both irrigated and nonirrigated lysimeters. Laboratory tests were conducted to determine how leachate from uranium tailings interacts with geologic materials. Acid leach tailings and tailings solution and geologic materials typical of mill site tailing pits were physically and chemically characterized. Investigation was made of the sorption characteristics of heavy metals and radionuclides on the geologic materials under low and neutral pH conditions. From solubility tests conducted at Pacific Northwest Laboratory, thermodynamic considerations predicted that for the Eh-pH range of natural aqueous environment, the dominant species of Pu is likely to be Pu(V) in relatively oxidizing environments and Pu(III) in reducing environments. Radionuclide transport through unsaturated media was investigated by using two solute transport models to describe the transport of tritium and strontium-85 in laboratory columns. A new approach was used to analyze radon emissions from uranium mill tailings

Optimal waste heat recovery and reuse in industrial zones

International Nuclear Information System (INIS)

Stijepovic, Mirko Z.; Linke, Patrick

2011-01-01

Significant energy efficiency gains in zones with concentrated activity from energy intensive industries can often be achieved by recovering and reusing waste heat between processing plants. We present a systematic approach to target waste heat recovery potentials and design optimal reuse options across plants in industrial zones. The approach first establishes available waste heat qualities and reuse feasibilities considering distances between individual plants. A targeting optimization problem is solved to establish the maximum possible waste heat recovery for the industrial zone. Then, a design optimization problem is solved to identify concrete waste heat recovery options considering economic objectives. The paper describes the approach and illustrates its application with a case study. -- Highlights: → Developed a systematic approach to target waste heat recovery potentials and to design optimal recovery and reuse options across plants in industrial zones. → Five stage approach involving data acquisition, analysis, assessment, targeting and design. → Targeting optimization problem establishes the maximum possible waste heat recovery and reuse limit for the industrial zone. → Design optimization problem provides concrete waste heat recovery and reuse network design options considering economic objectives.

Managing mixed wastes: technical issues

International Nuclear Information System (INIS)

Lytle, J.E.; Eyman, L.D.; Burton, D.W.; McBrayer, J.F.

1986-01-01

The US Department of Energy manages wastes that are both chemically hazardous and radioactive. These mixed wastes are often unique and many have national security implications. Management practices have evolved over the more than forty years that the Department and its predecessor agencies have been managing these wastes, both in response to better understanding of the hazards involved and in response to external, regulatory influences. The Department has recently standarized its waste management practices and has initited an R and D program to address priority issues identified by its operating contractor organizations. The R and D program is guided by waste management strategy that emphasizes reduction of human exposure to hazardous wastes in the environment, reduction of the amount and toxicity of wastes generated, treatment of wastes that are generated to reduce volumes and toxicities, and identification of alternatives to land disposal of wastes that remain hazardous following maximum practicable treatment

Optimization of control parameters for petroleum waste composting

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

Composting is being widely employed in the treatment of petroleum waste. The purpose of this study was to find the optimum control parameters for petroleum waste in-vessel composting. Various physical and chemical parameters were monitored to evaluate their influence on the microbial communities present in composting. The CO2 evolution and the number of microorganisms were measured as theactivity of composting. The results demonstrated that the optimum temperature, pH and moisture content were 56.5-59.5, 7.0-8.5 and 55%-60%, respectively. Under the optimum conditions, the removal efficiency of petroleum hydrocarbon reached 83.29% after 30 days composting.

High-resolution moisture profiles from full-waveform probabilistic inversion of TDR signals

Science.gov (United States)

Laloy, Eric; Huisman, Johan Alexander; Jacques, Diederik

2014-11-01

This study presents an novel Bayesian inversion scheme for high-dimensional undetermined TDR waveform inversion. The methodology quantifies uncertainty in the moisture content distribution, using a Gaussian Markov random field (GMRF) prior as regularization operator. A spatial resolution of 1 cm along a 70-cm long TDR probe is considered for the inferred moisture content. Numerical testing shows that the proposed inversion approach works very well in case of a perfect model and Gaussian measurement errors. Real-world application results are generally satisfying. For a series of TDR measurements made during imbibition and evaporation from a laboratory soil column, the average root-mean-square error (RMSE) between maximum a posteriori (MAP) moisture distribution and reference TDR measurements is 0.04 cm3 cm-3. This RMSE value reduces to less than 0.02 cm3 cm-3 for a field application in a podzol soil. The observed model-data discrepancies are primarily due to model inadequacy, such as our simplified modeling of the bulk soil electrical conductivity profile. Among the important issues that should be addressed in future work are the explicit inference of the soil electrical conductivity profile along with the other sampled variables, the modeling of the temperature-dependence of the coaxial cable properties and the definition of an appropriate statistical model of the residual errors.

Radioactive gaseous waste processing device

International Nuclear Information System (INIS)

Murakami, Kazuo.

1997-01-01

In a radioactive gaseous waste processing device, a dehumidifier in which a lot of hollow thread membranes are bundled and assembled is disposed instead of a dehumidifying cooling device and a dehumidifying tower. The dehumidifier comprises a main body, a great number of hollow thread membranes incorporated in the main body, a pair of fixing members for bundling and fixing both ends of the hollow thread membranes, a pair of caps for allowing the fixing members to pass through and fixing them on both ends of the main body, an off gas flowing pipe connected to one of the caps, a gas exhaustion pipe connected to the other end of the cap and a moisture removing pipeline connected to the main body. A flowrate control valve is connected to the moisture removing pipeline, and the other end of the moisture removing pipeline is connected between a main condensator and an air extraction device. Then, cooling and freezing devices using freon are no more necessary, and since the device uses the vacuum of the main condensator as a driving source and does not use dynamic equipments, labors for the maintenance is greatly reduced to improve economical property. The facilities are reduced in the size thereby enabling to use space effectively. (N.H.)

Soil Moisture Estimation Using MODIS Images (Case Study: Mashhad Plain Area

Directory of Open Access Journals (Sweden)

M. Fashaee

2016-09-01

Full Text Available Introduction: Numerous studies have been undertaken based on satellite imagery in order to estimate soil moisture using vegetation indices such as NDVI. Previous studies suffer from a restriction; these indices are not able to estimate where the vegetative coverage is low or where no vegetation exists. Hence, it is essential to develop a model which can overcome this restriction. Focus of this research is on estimation of soil moisture for low or scattered vegetative land covers. Trapezoidal temperature-vegetation (Ts~VI model is able to consider the status of soil moisture and vegetation condition. It can estimate plant water deficit for weak or no vegetation land cover. Materials and Methods: Moran proposed Water Deficit Index (WDI for evaluating field evapotranspiration rates and relative field water deficit for both full-cover and partially vegetated sites. The theoretical basis of this method is based on the energy balance equation. Penman-Monteith equation of energy balance was used to calculate the coordinates of the four vertices of the temperature-vegetation trapezoid also for four different extreme combinations of temperature and vegetation. For the (Ts−Ta~Vc trapezoid, four vertices correspond to 1 well-watered full-cover vegetation, 2 water-stressed full-cover vegetation, 3 saturated bare soil, and 4 dry bare soil. WDI is equal to 0 for well-watered conditions and equals to 1 for maximum stress conditions. As suggested by Moran et al. to draw a trapezoidal shape, some field measurements are required such as wind speed at the height of 2 meters, air pressure, mean daily temperature, vapor pressure-temperature curve slope, Psychrometrics constant, vapor pressure at mean temperature, vapor pressure deficit, external radiation, solar radiation of short wavelength, longwave radiation, net radiation, soil heat flux and air aerodynamic resistance is included. Crop vegetation and canopy resistance should be measured or estimated. The study

Effect of Soil Moisture Content on Growth, Crude Drug "Cho-to-ko" Yield and Oxindole Alkaloid Content of Uncaria rhynchophylla (B. LIVING SCIENCE)

OpenAIRE

川添, 禎浩; 小林, 茂樹; 水上, 元; 大橋, 裕; SADAHIRO, KAWAZOE; SHIGEKI, KOBAYASHI; HAJIME, MIZUKAMI; HIROMU, OHASHI; Laboratory of Environmetal Health and Toxicology, Department of Food Science and Nutrition, Kyoto Prefectural University; Department of Medicinal Plant Research, Faculty of Pharmaceutical Sciences, Nagasaki University; Department of Medicinal Plant Research, Faculty of Pharmaceutical Sciences, Nagasaki University; Department of Medicinal Plant Research, Faculty of Pharmaceutical Sciences, Nagasaki University

1992-01-01

Uncaria rhynchophylla was cultivated by using soil with various moisture contents (20,40,60,80 or 100% of the maximum moisture content retained by soil). Both growth and crude drug "Cho-to-ko" (dried stem with hooks of U. rhynchophylla) yield of the plant were in the following order : 60%> 80%> 40%> 100%> 20%, while oxindole alkaloid content of the stem was in the following order : 20%> 60%> 100%> 40%> 80%. It is concluded that moderately wet soil is suitable for cultivation of U. rhynchophyl...

CPAC optical moisture monitoring: Characterization of composition and physical effects on moisture determination Task 2A report

International Nuclear Information System (INIS)

Veltkamp, D.J.

1994-01-01

The impact of particle size and chemical composition variations on determination of tank simulant moisture from near infrared (NIR) optical spectra are presented. This work shows particle size and chemical variations will impact moisture predictions from NIR spectra. However, the prediction errors can be minimized if calibration models are built with samples containing these variations as interferents. Prior work showed the NIR spectral region (1100 to 2500 nm) could be used to predict moisture content of BY-104 tank simulant with a standard error less of approximately 0.5 wt%. Particle size will increase moisture prediction error if calibration-models do not include the same particle size ranges as unknown samples. A combined particle size model with 0-420 x10 -6 m, 420-841 x 10 -6 m, and 841 x 10 -6 m-2 mm diameter particles predicted 0.59, 0.34 nd 0.23 wt% errors respectively for samples containing only these size ranges and 0.80 wt% error for a samples with all particle size ranges. Chemical composition would also increase moisture prediction error if calibration model samples chemically differ from unknown samples. For a BY-104 simulant, increases in NaOH, NaAlO 2 , Na 2 SiO 3 , and Na 3 PO 4 produced moisture predictions that were lower than the actual moisture levels while increases in FE(NO 3 ) 3 , Ca(NO 3 ) 2 , and Mg (NO 3 ) 2 resulted in a higher than actual moisture prediction. Systematic changes in the NIR spectra could be observed for these families of materials. When all of the composition variations were included in a single model, the model had a moisture prediction error of 1.41 wt% as compared to a 2.96 wt% error without model changes. This work shows a calibration model based on a single set of tightly controlled experimental conditions will tend to have somewhat larger prediction errors when applied to samples collected with variations outside of such conditions

Nematode survival in relation to soil moisture

NARCIS (Netherlands)

Simons, W.R.

1973-01-01

Established nematode populations are very persistent in the soil. It is known that they need sufficient soil moisture for movement, feeding and reproduction (fig. 5), and that there are adverse soil moisture conditions which they cannot survive. The influence of soil moisture on survival

Technical basis for the reduction of the maximum temperature TGA-MS analysis of oxide samples from the 3013 destructive examination program

International Nuclear Information System (INIS)

Scogin, J. H.

2016-01-01

Thermogravimetric analysis with mass spectroscopy of the evolved gas (TGA-MS) is used to quantify the moisture content of materials in the 3013 destructive examination (3013 DE) surveillance program. Salts frequently present in the 3013 DE materials volatilize in the TGA and condense in the gas lines just outside the TGA furnace. The buildup of condensate can restrict the flow of purge gas and affect both the TGA operations and the mass spectrometer calibration. Removal of the condensed salts requires frequent maintenance and subsequent calibration runs to keep the moisture measurements by mass spectroscopy within acceptable limits, creating delays in processing samples. In this report, the feasibility of determining the total moisture from TGA-MS measurements at a lower temperature is investigated. A temperature of the TGA-MS analysis which reduces the complications caused by the condensation of volatile materials is determined. Analysis shows that an excellent prediction of the presently measured total moisture value can be made using only the data generated up to 700 °C and there is a sound physical basis for this estimate. It is recommended that the maximum temperature of the TGA-MS determination of total moisture for the 3013 DE program be reduced from 1000 °C to 700 °C. It is also suggested that cumulative moisture measurements at 550 °C and 700°C be substituted for the measured value of total moisture in the 3013 DE database. Using these raw values, any of predictions of the total moisture discussed in this report can be made.

Technical basis for the reduction of the maximum temperature TGA-MS analysis of oxide samples from the 3013 destructive examination program

Energy Technology Data Exchange (ETDEWEB)

Scogin, J. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-03-24

Thermogravimetric analysis with mass spectroscopy of the evolved gas (TGA-MS) is used to quantify the moisture content of materials in the 3013 destructive examination (3013 DE) surveillance program. Salts frequently present in the 3013 DE materials volatilize in the TGA and condense in the gas lines just outside the TGA furnace. The buildup of condensate can restrict the flow of purge gas and affect both the TGA operations and the mass spectrometer calibration. Removal of the condensed salts requires frequent maintenance and subsequent calibration runs to keep the moisture measurements by mass spectroscopy within acceptable limits, creating delays in processing samples. In this report, the feasibility of determining the total moisture from TGA-MS measurements at a lower temperature is investigated. A temperature of the TGA-MS analysis which reduces the complications caused by the condensation of volatile materials is determined. Analysis shows that an excellent prediction of the presently measured total moisture value can be made using only the data generated up to 700 °C and there is a sound physical basis for this estimate. It is recommended that the maximum temperature of the TGA-MS determination of total moisture for the 3013 DE program be reduced from 1000 °C to 700 °C. It is also suggested that cumulative moisture measurements at 550 °C and 700°C be substituted for the measured value of total moisture in the 3013 DE database. Using these raw values, any of predictions of the total moisture discussed in this report can be made.

Assessment of SMOS Soil Moisture Retrieval Parameters Using Tau-Omega Algorithms for Soil Moisture Deficit Estimation

Science.gov (United States)

Srivastava, Prashant K.; Han, Dawei; Rico-Ramirez, Miguel A.; O'Neill, Peggy; Islam, Tanvir; Gupta, Manika

2014-01-01

Soil Moisture and Ocean Salinity (SMOS) is the latest mission which provides flow of coarse resolution soil moisture data for land applications. However, the efficient retrieval of soil moisture for hydrological applications depends on optimally choosing the soil and vegetation parameters. The first stage of this work involves the evaluation of SMOS Level 2 products and then several approaches for soil moisture retrieval from SMOS brightness temperature are performed to estimate Soil Moisture Deficit (SMD). The most widely applied algorithm i.e. Single channel algorithm (SCA), based on tau-omega is used in this study for the soil moisture retrieval. In tau-omega, the soil moisture is retrieved using the Horizontal (H) polarisation following Hallikainen dielectric model, roughness parameters, Fresnel's equation and estimated Vegetation Optical Depth (tau). The roughness parameters are empirically calibrated using the numerical optimization techniques. Further to explore the improvement in retrieval models, modifications have been incorporated in the algorithms with respect to the sources of the parameters, which include effective temperatures derived from the European Center for Medium-Range Weather Forecasts (ECMWF) downscaled using the Weather Research and Forecasting (WRF)-NOAH Land Surface Model and Moderate Resolution Imaging Spectroradiometer (MODIS) land surface temperature (LST) while the s is derived from MODIS Leaf Area Index (LAI). All the evaluations are performed against SMD, which is estimated using the Probability Distributed Model following a careful calibration and validation integrated with sensitivity and uncertainty analysis. The performance obtained after all those changes indicate that SCA-H using WRF-NOAH LSM downscaled ECMWF LST produces an improved performance for SMD estimation at a catchment scale.

FOUNDRY WASTE MANAGEMENT

Directory of Open Access Journals (Sweden)

Borut Kosec

2008-06-01

Full Text Available Waste management in foundries is gaining a higher ecological and economical importance. Waste is becoming an increasingly traded product, where excellent profits can be made. Due to the cost reduction and successful business operation in companies, waste has to be regenerated and used again as a material to the maximum possible extent. Such research is long lasting and expensive and is a great challenge for companies. In the frame of our research, a total waste management case study for the Slovenian foundry Feniks was carried out. From the sustainable development point of view, waste management is most suitable, since it ensures the material utilization of waste, reduces the consumption of natural renewable or non-renewable resources and makes efficient production capacity utilization possible. Properly treated ecologically safe waste with a suitable physical characteristic, long-term existence, is a substitute for natural materials. Sand, dust, slag and other mineral waste from foundries are increasingly being used as materials in other industries. The foundry Feniks was awarded with certification of the environmental management system according to the standard SIST EN ISO 14001 and confirmed its environmental credentials.

Design of Stirrer Impeller with Variable Operational Speed for a Food Waste Homogenizer

OpenAIRE

Idris A. Kayode; Emmanuel O. B. Ogedengbe; Marc A. Rosen

2016-01-01

A conceptualized impeller called KIA is designed for impact agitation of food waste in a homogenizer. A comparative analysis of the performance of KIA is made with three conventional impeller types, Rushton, Anchor, and Pitched Blade. Solid–liquid mixing of a moisture-rich food waste is simulated under various operational speeds, in order to compare the dispersions and thermal distributions at homogenous slurry conditions. Using SolidWorks, the design of the impellers employs an Application P...

Survey of Optimal Temperature and Moisture for Worms Growth and Operating Vermicompost Production of Food Wastes

OpenAIRE

A Eslami; A Nabaey; R Rostami

2009-01-01

"n "nBackground and Objectives:Nowadays vermicompost production of food wastes is posed as one of appropriate methods to food wastes. disposal, its production used in agriculture and gardening. Moreover this process has some by products beside useful fertilizer that one of them is the worms. we can use them in variety of products specially in production of poultry and fish food. So determination of optimal condition for operating vermicompost production process of food wastes and worms. growt...

Investigation of layered covers designed to limit infiltration at waste disposal sites

International Nuclear Information System (INIS)

Johnson, T.M.; Herzog, B.L.; Cartwright, K.; Larson, T.H.

1983-01-01

Layered soils of highly contrasting texture have been shown to act as a barrier to infiltration because of differences in unsaturated hydraulic properties. Water infiltrating into a fine-grained soil overlying an unsaturated gravel will not enter the gravel until the overlying material is nearly saturated. As a result of what is commonly called the wick effect, moisture will flow laterally through the fine-grained soil above the gravel layer. Layered covers of compacted soil materials utilizing this phenomenon have been proposed to limit infiltration at waste disposal sites. A study funded by the US Nuclear Regulatory Commission is underway to evaluate the potential use of layered trench covers to minimize infiltration at low-level radioactive waste disposal sites. Moisture movement through layered covers consisting of compacted fine-grained soils and sand or gravel was modeled, using a one-dimensional finite-difference model to compare with laboratory column experiments and a two-dimensional finite-element model for field-scale simulations. Soil-moisture characteristic data were obtained from laboratory experiments and the hydraulic conductivity was calculated as a function of capillary pressure. The numerical simulations indicate that layered covers using various combinations of compacted fine-grained soils and coarse-grained material are able to substantially reduce infiltration. Laboratory column experiments using a dual-gamma ray attenuation system to measure moisture content and density simultaneously have been used to observe the behavior of layered soils and to select materials for field testing. Currently underway are field-scale studies of alternative cover designs selected on the basis of two-dimensional modeling

The use of remotely-sensed snow, soil moisture and vegetation indices to develop resilience to climate change in Kazakhstan

Science.gov (United States)

Saidaliyeva, Zarina; Davenport, Ian; Nobakht, Mohamad; White, Kevin; Shahgedanova, Maria

2017-04-01

Kazakhstan is a major producer of grain. Large scale grain production dominates in the north, making Kazakhstan one of the largest exporters of grain in the world. Agricultural production accounts for 9% of the national GDP, providing 25% of national employment. The south relies on grain production from household farms for subsistence, and has low resilience, so is vulnerable to reductions in output. Yields in the south depend on snowmelt and glacier runoff. The major limit to production is water supply, which is affected by glacier retreat and frequent droughts. Climate change is likely to impact all climate drivers negatively, leading to a decrease in crop yield, which will impact Kazakhstan and countries dependent on importing its produce. This work makes initial steps in modelling the impact of climate change on crop yield, by identifying the links between snowfall, soil moisture and agricultural productivity. Several remotely-sensed data sources are being used. The availability of snowmelt water over the period 2010-2014 is estimated by extracting the annual maximum snow water equivalent (SWE) from the Globsnow dataset, which assimilates satellite microwave observations with field observations to produce a spatial map. Soil moisture over the period 2010-2016 is provided by the ESA Soil Moisture and Ocean Salinity (SMOS) mission. Vegetation density is approximated by the Normalised Difference Vegetation Index (NDVI) produced from NASA's MODIS instruments. Statistical information on crop yields is provided by the Ministry of National Economy of the Republic of Kazakhstan Committee on Statistics. Demonstrating the link between snowmelt yield and agricultural productivity depends on showing the impact of snow mass during winter on remotely-sensed soil moisture, the link between soil moisture and vegetation density, and finally the link between vegetation density and crop yield. Soil moisture maps were extracted from SMOS observations, and resampled onto a 40km x

7 CFR 868.307 - Moisture.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Moisture. 868.307 Section 868.307 Agriculture Regulations of the Department of Agriculture (Continued) GRAIN INSPECTION, PACKERS AND STOCKYARD... Application of Standards § 868.307 Moisture. Water content in milled rice as determined by an FGIS approved...

Space-time modeling of soil moisture

Science.gov (United States)

Chen, Zijuan; Mohanty, Binayak P.; Rodriguez-Iturbe, Ignacio

2017-11-01

A physically derived space-time mathematical representation of the soil moisture field is carried out via the soil moisture balance equation driven by stochastic rainfall forcing. The model incorporates spatial diffusion and in its original version, it is shown to be unable to reproduce the relative fast decay in the spatial correlation functions observed in empirical data. This decay resulting from variations in local topography as well as in local soil and vegetation conditions is well reproduced via a jitter process acting multiplicatively over the space-time soil moisture field. The jitter is a multiplicative noise acting on the soil moisture dynamics with the objective to deflate its correlation structure at small spatial scales which are not embedded in the probabilistic structure of the rainfall process that drives the dynamics. These scales of order of several meters to several hundred meters are of great importance in ecohydrologic dynamics. Properties of space-time correlation functions and spectral densities of the model with jitter are explored analytically, and the influence of the jitter parameters, reflecting variabilities of soil moisture at different spatial and temporal scales, is investigated. A case study fitting the derived model to a soil moisture dataset is presented in detail.

Effects of a potential drop of a shipping cask, a waste container, and a bare fuel assembly during waste-handling operations

International Nuclear Information System (INIS)

Wu, C.L.; Lee, J.; Lu, D.L.; Jardine, L.J.

1991-12-01

This study investigates the effects of potential drops of a typical shipping cask, waste container, and bare fuel assembly during waste-handling operations at the prospective Yucca Mountain Repository. The waste-handling process (one stage, no consolidation configuration) is examined to estimate the maximum loads imposed on typical casks and containers as they are handled by various pieces of equipment during waste-handling operations. Maximum potential drop heights for casks and containers are also evaluated for different operations. A nonlinear finite-element model is employed to represent a hybrid spent fuel container subject to drop heights of up to 30 ft onto a reinforced concrete floor. The impact stress, strain, and deformation are calculated, and compared to the failure criteria to estimate the limiting (maximum permissible) drop height for the waste container. A typical Westinghouse 17 x 17 PWR fuel assembly is analyzed by a simplified model to estimate the energy absorption by various parts of the fuel assembly during a 30 ft drop, and to determine the amount of kinetic energy in a fuel pin at impact. A nonlinear finite-element analysis of an individual fuel pin is also performed to estimate the amount of fuel pellet fracture due to impact. This work was completed on May 1990

Mass and element balance in food waste composting facilities.

Science.gov (United States)

Zhang, Huijun; Matsuto, Toshihiko

2010-01-01

The mass and element balance in municipal solid waste composting facilities that handle food waste was studied. Material samples from the facilities were analyzed for moisture, ash, carbon, nitrogen, and the oxygen consumption of compost and bulking material was determined. Three different processes were used in the food waste composting facilities: standard in-vessel composting, drying, and stand-alone composting machine. Satisfactory results were obtained for the input/output ash balance despite several assumptions made concerning the quantities involved. The carbon/nitrogen ratio and oxygen consumption values for compost derived only from food waste were estimated by excluding the contribution of the bulking material remaining in the compost product. These estimates seemed to be suitable indices for the biological stability of compost because there was a good correlation between them, and because the values seemed logical given the operating conditions at the facilities. 2010 Elsevier Ltd. All rights reserved.

Novel Activated Carbons from Agricultural Wastes and their Characterization

Directory of Open Access Journals (Sweden)

S. Karthikeyan

2008-01-01

Full Text Available Solid waste disposal has become a major problem in India, Either it has to be disposed safely or used for the recovery of valuable materials as agricultural wastes like turmeric waste, ferronia shell waste, jatropha curcus seed shell waste, delonix shell waste and ipomea carnia stem. Therefore these wastes have been explored for the preparation of activated carbon employing various techniques. Activated carbons prepared from agricultural solid wastes by chemical activation processes shows excellent improvement in the surface characteristics. Their characterization studies such as bulk density, moisture content, ash content, fixed carbon content, matter soluble in water, matter soluble in acid, pH, decolourising power, phenol number, ion exchange capacity, ion content and surface area have been carried out to assess the suitability of these carbons as absorbents in the water and wastewater. For anionic dyes (reactive, direct, acid a close relationship between the surface area and surface chemical groups of the modified activated carbon and percentage of dye removal by adsorption can be observed. Cationic dyes large amount of surface chemical groups present in the sample (mainly carboxylic, anhydrides, lactones and phenols etc. are good anchoring sites for adsorption. The present study reveals the recovery of valuable adsorbents from readily and cheaply available agriculture wastes.

Biogas performance from co-digestion of Taihu algae and kitchen wastes

International Nuclear Information System (INIS)

Zhao, Ming-Xing; Ruan, Wen-Quan

2013-01-01

Highlights: • Co-digestion mode improves the biogas yield of Taihu algae and kitchen wastes. • Neutral protease enzyme reached maximum in algae only group. • The activity of dehydrogenase enzyme in mixed substrate groups was higher than that of algae and kitchen wastes only group. - Abstract: Co-digestion of Taihu algae with high carbon content substrate can balance the nutrients in the fermentation process. In this study, optimal mixing ratio for co-digestion of Taihu algae and kitchen wastes were investigated in order to improve biogas production potential. The results indicated that the biogas yield reached 388.6 mL/gTS at C/N15:1 group, which was 1.29 and 1.18 times of algae and kitchen wastes only. The maximum concentration of VFA reached 4239 mg/L on 8th day in kitchen wastes group, which was 1.21 times of algae group. Neutral protease enzyme activity in algae group reached maximum of 904.2 μg/(gTS h), while dehydrogenase enzyme at C/N 15:1 group reached maximum of 3402.2 μgTF/(gTS h). The feasibility of adjusting the C/N with co-digestion of Taihu algae and kitchen wastes to increase biogas production was demonstrated. Remarkably, the C/N of 15:1 was found to be the most appropriate ratio

Optical transparency of paper as a function of moisture content with applications to moisture measurement.

Science.gov (United States)

Forughi, A F; Green, S I; Stoeber, B

2016-02-01

Accurate measurement of the moisture content of paper is essential in papermaking and is also important in some paper-based microfluidic devices. Traditional measurement techniques provide very limited spatiotemporal resolution and working range. This article presents a novel method for moisture content measurement whose operating principle is the strong correlation between the optical transparency of paper and its moisture content. Spectrographic and microscopic measurement techniques were employed to characterize the relation of moisture content and relative transparency of four types of paper: hardwood chemi-thermomechanical pulp paper, Northern bleached softwood kraft paper, unbleached softwood kraft paper, and General Electric(®) Whatman™ grade 1 chromatography paper. It was found that for all paper types, the paper transparency increased monotonically with the moisture content (as the ratio of the mass-of-water to the mass-of-dry-paper increased from 0% to 120%). This significant increase in relative transparency occurred due to the refractive index matching role of water in wet paper. It is further shown that mechanical loading of the paper has little impact on the relative transparency, for loadings that would be typical on a paper machine. The results of two transient water absorption experiments are presented that show the utility and accuracy of the technique.

Immobilization of radioactive waste in glass matrices

International Nuclear Information System (INIS)

Wicks, G.G.

1978-01-01

A promising process for long-term management of high-level radioactive waste is to immobilize the waste in a borosilicate glass matrix. Among the most important criteria characterizing the integrity of the large-scale glass-waste forms are that they possess good chemical stability (including low leachability), thermal stability, mechanical integrity, and high radiation stability. Fulfillment of these criteria ensures the maximum margin of safety of glass-waste products, following solidification, handling, transportation, and long-term storage

Design and analysis of siloxanes removal by adsorption from landfill gas for waste-to-energy processes.

Science.gov (United States)

Elwell, Anthony C; Elsayed, Nada H; Kuhn, John N; Joseph, Babu

2018-03-01

Separation of volatile methyl siloxanes from landfill gas using fixed adsorption beds was modeled with the objective of identifying appropriate technology and the economics associated with this purification step. A general adsorption model assuming plug flow and radial symmetry was developed and used to conduct a parametric sweep of 162 unique cases. The varied parameters were adsorbent type (activated carbon and silica gel), bed height (3.05-9.15 m/10-30 ft), inlet siloxane concentration (5-15 mg/m 3 ), moisture content (0-100% relative humidity at STP or RH), and siloxane tolerance limit (0.094-9.4 mg/m 3 ) that correlated to three distinct energy conversion technologies (electricity production using engines or fuels cells or catalytic conversion to liquid hydrocarbon fuels). Due to the detrimental effect of RH on siloxane absorption, the maximum allowable moisture content of LFG before purification is 50% RH and moisture removal processes are also required. The design calculations using a selected case study show that the adsorption bed height required needed for 6 months minimum breakthrough time for catalytic fuel production is twice that for engine applications. Fuel cell applications require 3 times the bed height compared to engine applications. However, the purification costs amounted to 94%, 16% and 52% of recovered product value for engine, liquefaction, and fuel cell applications, respectively indicating the need for a high value product to justify purification costs. The approaches and conclusions can be extended to specific process conditions for landfill gas purification and to other processes that use biogas produced from waste as a feedstock. Copyright © 2017 Elsevier Ltd. All rights reserved.

The characterization of cement waste form for final disposal of decommissioned concrete waste

International Nuclear Information System (INIS)

Lee, K.W.; Lee, Y.J.; Hwang, D.S.; Moon, J.K.

2015-01-01

Since the decommissioning of nuclear plants and facilities, large quantities of slightly contaminated concrete waste have been generated. In Korea, the decontamination and decommissioning of the KRR-1, 2 at the KAERI have been under way. In addition, 83 drums of 200 l, and 41 containers of 4 m 3 of concrete waste were generated. Conditioning of concrete waste is needed for final disposal. Concrete waste is conditioned as follows: mortar using coarse and fine aggregates is filled into a void space after concrete rubble pre-placement into 200 l drums. Thus, this research developed an optimizing mixing ratio of concrete waste, water, and cement, and evaluated the characteristics of a cement waste form to meet the requirements specified in the disposal site specific waste acceptance criteria. The results obtained from compressive strength test, leaching test, and thermal cycling test of cement waste forms conclude that the concrete waste, water, and cement have been suggested to have 75:15:10 as the optimized mixing ratio. In addition, the compressive strength of cement waste form was satisfied, including fine powder up to a maximum 40 wt% in concrete debris waste of about 75%. (authors)

Effects of moisture, elevated temperature, and fatigue loading on the behavior of graphite/epoxy buffer strip panels with center cracks

Science.gov (United States)

Bigelow, C. A.

1988-01-01

The effects of fatigue loading combined with moisture and heat on the behavior of graphite epoxy panels with either Kevlar-49 or S-glass buffer strips were studied. Buffer strip panels, that had a slit in the center to represent damage, were moisture conditioned or heated, fatigue loaded, and then tested in tension to measure their residual strength. The buffer strips were parallel to the loading direction and were made by replacing narrow strips of the 0 deg graphite plies with Kevlar-49 epoxy or S-glass epoxy on a 1-for-1 basis. The panels were subjected to a fatigue loading spectrum. One group of panels was preconditioned by soaking in 60 C water to produce a 1 percent weight gain then tested at room temperature. One group was heated to 82 C during the fatigue loading. Another group was moisture conditioned and then tested at 82 C. The residual strengths of the buffer panels were not highly affected by the fatigue loading, the number of repetitions of the loading spectrum, or the maximum strain level. The moisture conditioning reduced the residual strengths of the S-glass buffer strip panel by 10 to 15 percent below the ambient results. The moisture conditioning did not have a large effect on the Kevlar-49 panels.

Ventilation System Strategy for a Prospective Korean Radioactive Waste Repository

International Nuclear Information System (INIS)

Kim, Jin; Kwon, Sang Ki

2005-01-01

In the stage of conceptual design for the construction and operation of the geologic repository for radioactive wastes, it is important to consider a repository ventilation system which serves the repository working environment, hygiene and safety of the public at large, and will allow safe maintenance like moisture content elimination in repository for the duration of the repositories life, construction/operation/closure, also allowing safe waste transportation and emplacement. This paper describes the possible ventilation system design criteria and requirements for the prospective Korean radioactive waste repositories with emphasis on the underground rock cavity disposal method in the both cases of low and medium-level and high-level wastes. It was found that the most important concept is separate ventilation systems for the construction (development) and waste emplacement (storage) activities. In addition, ventilation network system modeling, natural ventilation, ventilation monitoring systems and real time ventilation simulation, and fire simulation and emergency system in the repository are briefly discussed.

Distribution of temperature and moisture content fields in a rectangular beet pulp particle during convection drying

Directory of Open Access Journals (Sweden)

A. N. Ostrikov

2018-01-01

Full Text Available The mathematical model describing distribution of fields of temperatures and moisture contents in a particle of a squared beet press at convective drying is given. As the initial equations the differential equations of material and thermal balances in which transfer of warmth and weight is caused by phase transformations have been accepted. The algorithm of the numerical solution of a non-stationary regional problem of heat conductivity with variable heat and mass transfer coefficients of the dried-up product, boundary and entry conditions and also phase transition with mobile limit of the section of phases is developed for the solution of mathematical model. At the same time the initial system of the equations is given to a dimensionless look. For the solution of a problem of non-stationary heat conductivity the zone method of calculation of temperature fields when drying a beet press is used. Process of drying broke into some time intervals. Within each interval geometrical form of a particle, its density, heatphysical and mass-exchanged characteristics; initial distribution of temperature and moisture content on particle volume and also density of a mass and thermal stream with the evaporated moisture are constant. The zone method of the solution of a problem of the non-stationary three-dimensional equation of heat conductivity for a parallelepiped taking into account internal sources of warmth has been checked on experimental data of stationary drying of a beet press with use of basic data. For realization of a zone method dependences of change of the linear size of a particle of a beet press on spatial coordinate x and its moisture content in the course of drying are received. At constant values of moisture content and the sizes of the party of the dried-up particle on each step the method of a machine experiment has found the current values of coefficient of phase transformation on condition of the maximum rapprochement of settlement and

Role of the unsaturated zone in radioactive and hazardous waste disposal

International Nuclear Information System (INIS)

Mercer, J.W.; Marine, I.W.; Rao, P.S.C.

1983-01-01

The problems of hazardous and low-level radioactive waste disposal caused by the physical and chemical processes active in the unsaturated zone are explored in this book. The focus is on the use of laboratory analyses, field observations, and numerical and analytical calculations to create a clear picture of both problems and potential solutions. Topics include policy modeling, statistical techniques, liners, and field applications. Contents include: Modeling of Moisture Movement through Layered Trench Covers; Role of Partially Saturated Soil in Liner Design for Hazardous Waste Disposal Sites; Field Experiments to Determine Saturated Hydraulic Conductivity in the Vadose Zone; Role of Desaturation on Transport through Fractured Rock; Nuclear Waste Isolation in the Unsaturated Zone of Arid Regions

Report: new guidelines for characterization of municipal solid waste: the Portuguese case.

Science.gov (United States)

da Graça Madeira Martinho, Maria; Silveira, Ana Isabel; Fernandes Duarte Branco, Elsa Maria

2008-10-01

This report proposes a new set of guidelines for the characterization of municipal solid waste. It is based on an analysis of reference methodologies, used internationally, and a case study of Valorsul (a company that handles recovery and treatment of solid waste in the North Lisbon Metropolitan Area). In particular, the suggested guidelines present a new definition of the waste to be analysed, change the sampling unit and establish statistical standards for the results obtained. In these new guidelines, the sampling level is the waste collection vehicle and contamination and moisture are taken into consideration. Finally, focus is on the quality of the resulting data, which is essential for comparability of data between countries. These new guidelines may also be applicable outside Portugal because the methodology includes, besides municipal mixed waste, separately collected fractions of municipal waste. They are a response to the need for information concerning Portugal (e.g. Eurostat or OECD inquiries) and follow European Union municipal solid waste management policies (e.g. packaging waste recovery and recycling targets and the reduction of biodegradable waste going to landfill).

7 CFR 51.2561 - Average moisture content.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Average moisture content. 51.2561 Section 51.2561... STANDARDS) United States Standards for Grades of Shelled Pistachio Nuts § 51.2561 Average moisture content. (a) Determining average moisture content of the lot is not a requirement of the grades, except when...

Moisture Management for High R-Value Walls

Energy Technology Data Exchange (ETDEWEB)

Lepage, R. [Building Science Corporation, Somerville, MA (United States); Schumacher, C. [Building Science Corporation, Somerville, MA (United States); Lukachko, A. [Building Science Corporation, Somerville, MA (United States)

2013-11-01

This report explains the moisture-related concerns for high R-value wall assemblies and discusses past Building America research work that informs this study. In this project, hygrothermal simulations were prepared for several common approaches to High R-value wall construction in six cities (Houston, Atlanta, Seattle, St. Louis, Chicago, and International Falls) representing a range of climate zones. The modeling program assessed the moisture durability of the wall assemblies based on three primary sources of moisture: construction moisture, air leakage condensation, and bulk water leakage; the report presents results of the study.

Skin moisturization mechanisms: new data.

Science.gov (United States)

Bonté, F

2011-05-01

The main function of the skin is to protect the body against exogenous substances and excessive water loss. The skin barrier is located in the outermost layer of the skin, called the stratum corneum, which is composed of corneocytes, originating from the keratinocytes differentiation process, embedded in organized complex lipid domains. Moisturizing of the skin is recognized as the first anti-aging skin care. Skin moisturization is essential for its appearance, protection, complexion, softness and the reinforcement of its barrier properties against deleterious and exogenous environmental factors. The intrinsic water binding capacity of skin is not only due to the complex natural moisturizing factor present in corneocytes, but also to hyaluronic acid and a regulated water transport within the skin. Recent data shows that the water movements between the cells at the different levels of the epidermis are due to dedicated water and glycerol transport proteins named aquaporins. Their role in the skin moisturization is completed by corneodesmosomes and tight junctions. Water and pH are now shown to be of prime importance in the regulation of the epidermal enzymes linked to corneocytes desquamation and lipid synthesis. Furthermore, the level of moisturization of the skin is important in its protection against repeated exposure to various irritant agents or phenomena such as very frequent washing with strong tensioactive materials. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

Composting of tobacco plant waste by manual turning and forced aeration system

OpenAIRE

Nonglak Saithep

2009-01-01

The efficiency of tobacco plant waste composting, by the manual turning and the forced aeration system, was compared. Tobacco plant waste, cow manure, urea fertiliser, and a compost inoculum mixture at a 100:10:0.2:0.01 ratio respectively, with 60% (w/v) moisture content, were set up in piling forms. The piles of the manual turning system were provided with turning aeration by hand at intervals of 7 days during the composting process. For the forced aeration system, each pile was aerated by a...

A study of the natural biodegradation of two-phase olive mill solid waste during its storage in an evaporation pond.

Science.gov (United States)

Borja, R; Sánchez, E; Raposo, F; Rincón, B; Jiménez, A M; Martín, A

2006-01-01

A study of the natural biodegradation of two-phase olive mill solid waste (OMSW) during its storage in an evaporation pond was carried out. This system is traditionally used as the final disposal of this waste or constitutes a previous stage before being processed by cogeneration or anaerobic digestion processes. A laboratory-scale pond with a total volume of 520 l was used. The experiment was carried out between December 2002 and August 2003 covering a total period of 269 days. During the experiment, the variations of temperature (outside and inside the pond), the effective volume of the OMSW in the pond, moisture content, total solids (TS), volatile solids (VS), the total chemical oxygen demand (TCOD), total volatile acids (TVA), pH and cumulative methane production as a function of the operation time were evaluated. The experimental results obtained showed that the characteristics of the two-phase OMSW in the pond were dependent on the time of operation and temperature. During the experiment, three periods were clearly observed and differentiated: (a) An initial period with a rapid reduction of moisture content and effective volume, with an increase of TS, VS and TCOD removals, a decrease of pH and an increase of TVA and methane production until day 21. (b) A second period of slow decrease of moisture content and effective volume, due to the decrease of the ambient temperature. This period took place between day 21 and days 120-150 of assay, and it was characterised by a slight change in the OMSW properties. (c) A third period where the characteristics of the waste in the pond changed considerably due to the increase of the temperature outside the pond. The methane gas production also showed an increase due to the increase of methanogenic activity with the increase of temperature. An empirical model to describe the changes of two-phase OMSW characteristics and methane production with the operation time was developed. The proposed model, based on the use of

Study on Waste Composition at Taman Pura Kencana, Batu Pahat

Directory of Open Access Journals (Sweden)

Abdul Kadir Aeslina

2017-01-01

Full Text Available Municipal solid waste management is a major challenge due to the increase in population and the development of a country. The problems also arise when the lifespan of the landfills available are shorten than estimated. The aim of this study is to determine waste composition at Taman Pura Kencana. The waste collection was carried out for 50 houses on a daily basis. The collection and sorting out method was conducted based on Malaysian Standard MS 2505:2012 and the data collected is recorded. The result showed the moisture content was approximately ranging between 25% – 30%. The density for each waste has been calculated and the result was recorded accordingly. The highest density is metal followed by organic waste, glass, napkins, household hazardous waste, textiles, paper, plastic rigid, plastic film, rubber and tetrapek. The waste collected also were categorized and consisted of food waste/organic (43.75%, paper (17.97%, plastics rigid (13.58%, plastic film (10.62%, napkins (4.43%, glass (3.10%, household hazardous waste (1.68%, metal (1.67%, tetrapek (1.34% , rubber (0.93%, and textiles (0.92%. Results from the analysis illustrated that waste generation in Taman Pura Kencana may influenced by sudden changes in lifestyles, incomes, household size and also increase of population.

Quality Assurance of Rice and Paddy Moisture Measurements in Thailand

Science.gov (United States)

Sinhaneti, T.; Keawprasert, T.; Puuntharo, P.; Triarun, W.

2017-10-01

A bilateral comparison in moisture measurement between the National Institute of Metrology Thailand (NIMT) and the Central Bureau of Weights and Measures (CBWM) was organized for quality assuring of rice and paddy moisture measurement in Thailand. The bilateral comparison was conducted by using the same batch of sample and moisture meter as transfer device. It consisted of two parts: moisture measurement in rice and in paddy. A rice moisture meter belonging to CBWM and rice standards prepared at the nominal moisture content of 10 %, 12 %, 14 % and 16 % at NIMT, were used for rice moisture comparison, while a paddy moisture meter belonging to NIMT and paddy standards prepared at the nominal moisture content of 12 %, 14 %, 16 % and 18 % at CBWM, were used for paddy moisture comparison. Both laboratories measured the moisture content of a sample by using the standard method in ISO 712 and used that sample to calibrate a moisture meter by means of the method based on ISO 7700-1. Since the moisture content of the sample can change during the comparison, correction values in moisture content between the standard value and the reading value from the moisture meter are used as calibration results for the comparison evaluation. For the rice moisture comparison, differences in the correction value measured by the two laboratories vary from 0.18 % to 0.46 %, with their combined comparison uncertainty of 0.37 % (k= 2). The main contribution to the difference comes from the standard values from both laboratories differing from 0.27 % to 0.53 %, as the rice standard was found to drift in moisture content less than 0.05 %. Similarly to the rice moisture comparison, differences in the correction value for the paddy moisture measurement range from 0.08 % to 0.56 % with the combined comparison uncertainty of 0.38 % (k = 2), whereas the stability in moisture content of the paddy sample at NIMT was found to be within 0.12 %.

Waste management from pulp and paper production in the European Union

International Nuclear Information System (INIS)

Monte, M.C.; Fuente, E.; Blanco, A.; Negro, C.

2009-01-01

Eleven million tonnes of waste are produced yearly by the European pulp and paper industry, of which 70% originates from the production of deinked recycled paper. Wastes are very diverse in composition and consist of rejects, different types of sludges and ashes in mills having on-site incineration treatment. The production of pulp and paper from virgin pulp generates less waste but the waste has similar properties to waste from the production of deinked pulp, although with less inorganics. Due to legislation and increased taxes, landfills are quickly being eliminated as a final destination for wastes in Europe, and incineration with energy recovery is becoming the main waste recovery method. Other options such as pyrolysis, gasification, land spreading, composting and reuse as building material are being applied, although research is still needed for optimization of the processes. Due to the large volumes of waste generated, the high moisture content of the waste and the changing waste composition as a result of process conditions, recovery methods are usually expensive and their environmental impact is still uncertain. For this reason, it is necessary to continue research on different applications of wastes, while taking into account the environmental and economic factors of these waste treatments

Use of midlatitude soil moisture and meteorological observations to validate soil moisture simulations with biosphere and bucket models

Science.gov (United States)

Robock, Alan; Vinnikov, Konstantin YA.; Schlosser, C. Adam; Speranskaya, Nina A.; Xue, Yongkang

1995-01-01

Soil moisture observations in sites with natural vegetation were made for several decades in the former Soviet Union at hundreds of stations. In this paper, the authors use data from six of these stations from different climatic regimes, along with ancillary meteorological and actinometric data, to demonstrate a method to validate soil moisture simulations with biosphere and bucket models. Some early and current general circulation models (GCMs) use bucket models for soil hydrology calculations. More recently, the Simple Biosphere Model (SiB) was developed to incorporate the effects of vegetation on fluxes of moisture, momentum, and energy at the earth's surface into soil hydrology models. Until now, the bucket and SiB have been verified by comparison with actual soil moisture data only on a limited basis. In this study, a Simplified SiB (SSiB) soil hydrology model and a 15-cm bucket model are forced by observed meteorological and actinometric data every 3 h for 6-yr simulations at the six stations. The model calculations of soil moisture are compared to observations of soil moisture, literally 'ground truth,' snow cover, surface albedo, and net radiation, and with each other. For three of the stations, the SSiB and 15-cm bucket models produce good simulations of seasonal cycles and interannual variations of soil moisture. For the other three stations, there are large errors in the simulations by both models. Inconsistencies in specification of field capacity may be partly responsible. There is no evidence that the SSiB simulations are superior in simulating soil moisture variations. In fact, the models are quite similar since SSiB implicitly has a bucket embedded in it. One of the main differences between the models is in the treatment of runoff due to melting snow in the spring -- SSiB incorrectly puts all the snowmelt into runoff. While producing similar soil moisture simulations, the models produce very different surface latent and sensible heat fluxes, which

PRODUCTION OF BIOETHANOL FROM AGRICULTURAL WASTE

Directory of Open Access Journals (Sweden)

W. Braide

2016-05-01

Full Text Available This study investigates the potential of ethanol production from agro wastes. Agro waste from sugarcane Saccharum officinarum (sugarcane baggasse, sugarcane bark and maize plant Zea mays (corncob, corn stalk, corn husk was subjected to a pretreatment process using acid hydrolysis was applied to remove lignin which acts as physical barrier to cellulolytic enzymes. Ethanolic fermentation was done using Saccharomyces cerevisiae for 5days and the ethanol yield, specific gravity, pH and total reducing sugar were also determined. From the results, the specific gravity, sugar content and pH decreased over time while the Sugarcane baggasse, Sugarcane bark, Cornstalk, Corncob and Cornhusk gave maximum percentage ethanol yield of 6.72, 6.23, 6.17, 4.17 and 3.45 respectively at 72hrs Fermentation. Maximum yields of ethanol were obtained at pH 3.60, 3.82, 4.00, 3.64 and 3.65. These findings show/prove that ethanol can be made from the named agricultural waste and the process is recommended as a means of generating wealth from waste.

Simple grain moisture content determination from microwave measurements

International Nuclear Information System (INIS)

Kraszewski, A.W.; Trabelsi, S.; Nelson, S.O.

1998-01-01

Moisture content of wheat, Triticum aestivum L., is expressed as a function of the ratio of microwave attenuation and phase shift, measured at 16.8 GHz, and grain temperature. Validation of the calibration equation indicated that moisture content was obtained with an uncertainty less than +/- 0.45% moisture at the 95% confidence level, independent of density variation, at temperatures from -1 degree C to 42 degrees C, and moisture contents from 10% to 19%. Moisture determination does not depend on the layer thickness of the wheat norits bulk density. No differences between two wheat cultivars were observed in the measurement data

Heat and Moisture transport of socks

Science.gov (United States)

Komárková, P.; Glombíková, V.; Havelka, A.

2017-10-01

Investigating the liquid moisture transport and thermal properties is essential for understanding physiological comfort of clothes. This study reports on an experimental investigation of moisture management transport and thermal transport on the physiological comfort of commercially available socks. There are subjective evaluation and objective measurements. Subjective evaluation of the physiological comfort of socks is based on individual sensory perception of probands during and after physical exertion. Objective measurements were performed according to standardized methods using Moisture Management tester for measuring the humidity parameters and C-term TCi analyzer for thermal conductivity and thermal effusivity. The obtained values of liquid moisture transport and thermal properties were related to the material composition and structure of the tested socks. In summary, these results show that objective measurement corresponds with probands feelings.

The effects of moisture content, particle size and binding agent content on oil palm shell pellet quality parameters

Directory of Open Access Journals (Sweden)

Nelson Arzola

2012-01-01

Full Text Available Waste-to-energy represents a challenge for the oil palm industry worldwide. Bio-pellet production is an alternative way of adding value to oil palm biomass. This would mean that a product having major energy density becomes more mechanically stable and achieves better performance during combustion. This paper deals with oil palm shell pelleting; using binding agents having up to 25% mass keeping average particle size less than 1mm and moisture content up to 18.7% (d.b. were evaluated. An experimental factorial design used binding agent mass percentage, milled shell particle size and moisture content as factors. Pellet density response surfaces and durability index were obtained. Pellet performance during thermal-chemical transformation was also evaluated by using thermogravimetry equipment. The results led to technical evaluation of scale-up at industrial production level.

Moisture relations and physical properties of wood

Science.gov (United States)

Samuel V. Glass; Samuel L. Zelinka

2010-01-01

Wood, like many natural materials, is hygroscopic; it takes on moisture from the surrounding environment. Moisture exchange between wood and air depends on the relative humidity and temperature of the air and the current amount of water in the wood. This moisture relationship has an important influence on wood properties and performance. Many of the challenges of using...

Moisture Management for High R-Value Walls

Energy Technology Data Exchange (ETDEWEB)

Lepage, R.; Schumacher, C.; Lukachko, A.

2013-11-01

The following report explains the moisture-related concerns for High R-value wall assemblies and discusses past Building America research work that informs this study. Hygrothermal simulations were prepared for several common approaches to High R-value wall construction in six cities (Houston, Atlanta, Seattle, St. Louis, Chicago, and International Falls) representing a range of climate zones (2, 3, 4C, 4, 5A, and 7, respectively). The simulations are informed by experience gained from past research in this area and validated by field measurement and forensic experience. The modeling program was developed to assess the moisture durability of the wall assemblies based on three primary sources of moisture: construction moisture, air leakage condensation, and bulk water leakage. The peak annual moisture content of the wood based exterior sheathing was used to comparatively analyze the response to the moisture loads for each of the walls in each given city. Walls which experienced sheathing moisture contents between 20% and 28% were identified as risky, whereas those exceeding 28% were identified as very high risk. All of the wall assemblies perform well under idealized conditions. However, only the walls with exterior insulation, or cavity insulation which provides a hygrothermal function similar to exterior insulation, perform adequately when exposed to moisture loads. Walls with only cavity insulation are particularly susceptible to air leakage condensation. None of the walls performed well when a precipitation based bulk water leak was introduced to the backside of the sheathing, emphasizing the importance of proper flashing details.

Effect of osmopriming sources and moisture stress on wheat

International Nuclear Information System (INIS)

Amin, R.; Khan, A.Z.; Khalil, S.K.

2012-01-01

Wheat yield in Pakistan is very low due to poor germination and poor stand establishment and optimum amount of water availability at critical growth stages. To cope with these problems experiments were planned including control and nine osmopriming sources per liter of water that is PEG (100 g), KCl (37.25 g), KNO/sub 3/ (101 g), NaCl (58.5 g), NH/sub 4/ Cl (53.5 g), CaCl/sub 2/ (55.5 g), Mannitol (20 g), Na/sub 2/ SO/sub 4/ (71 g) and hydro priming. In the filed these were studied at three moisture stresses of 60, 70 and 80% MAD (management allowable depletion). The experiments were repeated during 2008 and 2009 and were laid out in randomized complete block design with split plot arrangement replicated three times. Moisture stress was allotted to main plots and osmopriming sources to sub plots. Best combinations of moisture stress (M) and osmopriming sources (OPS) significantly affected pheno logical and grain yield components of wheat. Increased moisture stress showed decreased pheno logical life of the wheat. Hence lowest days to maturity (157.1) were noted for 80% MAD. The optimum MAD (70%) contributed to maximum grain yield (3348.6 kg ha/sup -1/). Wheat showed variation in response to osmopriming sources. Minimum days to emergence (8.1) were noted for PEG. While KNO/sub 3/ osmoprimed seeds took lowest days to maturity (155.4). Highest emergence m/sup -2/ (82), thousand grains weight (39.97 g), and grain yield (3481 kg ha/sup -1/) were recorded for PEG (100 g L/sup -1/ of water). Likewise KNO/sub 3/ (101 g L/sup -1/ of water) osmoprimed seeds attained highest number of grains spike/sup -1/ (51.0). From this study it was concluded that wheat seeds may be osmoprimed with PEG, Na/sub 2/ SO/sub 4/, KNO/sub 3/, CaCl/sub 2/ and water along with the application of 70% MAD irrigation at critical growth stages for gaining high yield. However, due to the high prices of PEG and other osmopriming sources in the market hydro priming is recommended for gaining high net

Investigating soil moisture-climate interactions with prescribed soil moisture experiments: an assessment with the Community Earth System Model (version 1.2)

Science.gov (United States)

Hauser, Mathias; Orth, René; Seneviratne, Sonia I.

2017-04-01

Land surface hydrology is an important control of surface weather and climate. A valuable technique to investigate this link is the prescription of soil moisture in land surface models, which leads to a decoupling of the atmosphere and land processes. Diverse approaches to prescribe soil moisture, as well as different prescribed soil moisture conditions have been used in previous studies. Here, we compare and assess four methodologies to prescribe soil moisture and investigate the impact of two different estimates of the climatological seasonal cycle used to prescribe soil moisture. Our analysis shows that, though in appearance similar, the different approaches require substantially different long-term moisture inputs and lead to different temperature signals. The smallest influence on temperature and the water balance is found when prescribing the median seasonal cycle of deep soil liquid water, whereas the strongest signal is found when prescribing soil liquid and soil ice using the mean seasonal cycle. These results indicate that induced net water-balance perturbations in experiments investigating soil moisture-climate coupling are important contributors to the climate response, in addition to the intended impact of the decoupling. These results help to guide the set-up of future experiments prescribing soil moisture, as for instance planned within the Land Surface, Snow and Soil Moisture Model Intercomparison Project (LS3MIP).

Moisture Sorption in Porous Materials

DEFF Research Database (Denmark)

Nielsen, Lauge Fuglsang

2007-01-01

pressure and weight data can be "translated" to pore geometry by known physical relationships. In this context, analytical descriptions are important which can relate moisture condensation in pore structures to ambient vapor pressure. Such a description, the extended BET-relation, is presented...... physical parameters, the so-called BET-parameters: The heat property factor, C, and the pore surface, SBET (derived from the so-called uni-molecular moisture content uBET). A software ‘SORP07’ has been developed to handle any calculations made in the paper. For readers who have a special interest...... in the subject considered this software is available on request to the author. Keywords: Porous materials, moisture, adsorption, desorption, BET-parameters....

Mixed waste study, Lawrence Livermore National Laboratory Hazardous Waste Management facilities

International Nuclear Information System (INIS)

1990-11-01

This document addresses the generation and storage of mixed waste at Lawrence Livermore National Laboratory (LLNL) from 1984 to 1990. Additionally, an estimate of remaining storage capacity based on the current inventory of low-level mixed waste and an approximation of current generation rates is provided. Section 2 of this study presents a narrative description of Environmental Protection Agency (EPA) and Department of Energy (DOE) requirements as they apply to mixed waste in storage at LLNL's Hazardous Waste Management (HWM) facilities. Based on information collected from the HWM non-TRU radioactive waste database, Section 3 presents a data consolidation -- by year of storage, location, LLNL generator, EPA code, and DHS code -- of the quantities of low-level mixed waste in storage. Related figures provide the distribution of mixed waste according to each of these variables. A historical review follows in Section 4. The trends in type and quantity of mixed waste managed by HWM during the past five years are delineated and graphically illustrated. Section 5 provides an estimate of remaining low-level mixed waste storage capacity at HWM. The estimate of remaining mixed waste storage capacity is based on operational storage capacity of HWM facilities and the volume of all waste currently in storage. An estimate of the time remaining to reach maximum storage capacity is based on waste generation rates inferred from the HWM database and recent HWM documents. 14 refs., 18 figs., 9 tabs

Case study on prediction of remaining methane potential of landfilled municipal solid waste by statistical analysis of waste composition data.

Science.gov (United States)

Sel, İlker; Çakmakcı, Mehmet; Özkaya, Bestamin; Suphi Altan, H

2016-10-01

Main objective of this study was to develop a statistical model for easier and faster Biochemical Methane Potential (BMP) prediction of landfilled municipal solid waste by analyzing waste composition of excavated samples from 12 sampling points and three waste depths representing different landfilling ages of closed and active sections of a sanitary landfill site located in İstanbul, Turkey. Results of Principal Component Analysis (PCA) were used as a decision support tool to evaluation and describe the waste composition variables. Four principal component were extracted describing 76% of data set variance. The most effective components were determined as PCB, PO, T, D, W, FM, moisture and BMP for the data set. Multiple Linear Regression (MLR) models were built by original compositional data and transformed data to determine differences. It was observed that even residual plots were better for transformed data the R(2) and Adjusted R(2) values were not improved significantly. The best preliminary BMP prediction models consisted of D, W, T and FM waste fractions for both versions of regressions. Adjusted R(2) values of the raw and transformed models were determined as 0.69 and 0.57, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Combustion Characteristics Of Agricultural Waste-Coal Char Blends

International Nuclear Information System (INIS)

Akpabio, I. O; Danbature W

2002-01-01

Shortage of petroleum products, depletion of huge forest reserves for fuel purposes with its attendant erosion problems and other environmental considerations have necessitated investigations into other sources of fuel. In this wise. a set of seven types of briquettes were prepared from agricultural wastes such as rice husk, maize husk and saw-dust and blends of carbonized coal char. Strong and well-formed briquettes with good combustion characteristics were obtained. The results obtained from water boiling tests show that 2 litres of water could be boiled just under 23 minutes. Moisture contents and strengths of these briquettes were also determined and are discussed. The results show that wastes could be converted into useful fuel

Study on the optimal moisture adding rate of brown rice during germination by using segmented moisture conditioning method.

Science.gov (United States)

Cao, Yinping; Jia, Fuguo; Han, Yanlong; Liu, Yang; Zhang, Qiang

2015-10-01

The aim of this study was to find out the optimal moisture adding rate of brown rice during the process of germination. The process of water addition in brown rice could be divided into three stages according to different water absorption speeds in soaking process. Water was added with three different speeds in three stages to get the optimal water adding rate in the whole process of germination. Thus, the technology of segmented moisture conditioning which is a method of adding water gradually was put forward. Germinated brown rice was produced by using segmented moisture conditioning method to reduce the loss of water-soluble nutrients and was beneficial to the accumulation of gamma aminobutyric acid. The effects of once moisture adding amount in three stages on the gamma aminobutyric acid content in germinated brown rice and germination rate of brown rice were investigated by using response surface methodology. The optimum process parameters were obtained as follows: once moisture adding amount of stage I with 1.06 %/h, once moisture adding amount of stage II with 1.42 %/h and once moisture adding amount of stage III with 1.31 %/h. The germination rate under the optimum parameters was 91.33 %, which was 7.45 % higher than that of germinated brown rice produced by soaking method (84.97 %). The content of gamma aminobutyric acid in germinated brown rice under the optimum parameters was 29.03 mg/100 g, which was more than two times higher than that of germinated brown rice produced by soaking method (12.81 mg/100 g). The technology of segmented moisture conditioning has potential applications for studying many other cereals.

Waste statistics 2001

International Nuclear Information System (INIS)

2004-01-01

Reports to the ISAG (Information System for Waste and Recycling) for 2001 cover 402 Danish waste treatment plants owned by 295 enterprises. The total waste generation in 2001 amounted to 12,768,000 tonnes, which is 2% less than in 2000. Reductions are primarily due to the fact that sludge for mineralization is included with a dry matter content of 20% compared to 1,5% in previous statistics. This means that sludge amounts have been reduced by 808,886 tonnes. The overall rate of recycling amounted to 63%, which is 1% less than the overall recycling target of 64% for 2004. Since sludge has a high recycling rate, the reduction in sludge amounts of 808,886 tonnes has also caused the total recycling rate to fall. Waste amounts incinerated accounted for 25%, which is 1% more than the overall target of 24% for incineration in 2004. Waste going to landfill amounted to 10%, which is better than the overall landfill target for 2004 of a maximum of 12% for landfilling. Targets for treatment of waste from the different sectors, however, are still not complied with, since too little waste from households and the service sector is recycled, and too much waste from industry is led to landfill. (BA)

Waste statistics 2001

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

Reports to the ISAG (Information System for Waste and Recycling) for 2001 cover 402 Danish waste treatment plants owned by 295 enterprises. The total waste generation in 2001 amounted to 12,768,000 tonnes, which is 2% less than in 2000. Reductions are primarily due to the fact that sludge for mineralization is included with a dry matter content of 20% compared to 1,5% in previous statistics. This means that sludge amounts have been reduced by 808,886 tonnes. The overall rate of recycling amounted to 63%, which is 1% less than the overall recycling target of 64% for 2004. Since sludge has a high recycling rate, the reduction in sludge amounts of 808,886 tonnes has also caused the total recycling rate to fall. Waste amounts incinerated accounted for 25%, which is 1% more than the overall target of 24% for incineration in 2004. Waste going to landfill amounted to 10%, which is better than the overall landfill target for 2004 of a maximum of 12% for landfilling. Targets for treatment of waste from the different sectors, however, are still not complied with, since too little waste from households and the service sector is recycled, and too much waste from industry is led to landfill. (BA)

Influence of mineralogy and moisture content on plasticity and induced anisotropic damage of a clay-stone: application to nuclear waste disposals

International Nuclear Information System (INIS)

Chiarelli, A.S.; Sibai, M.; Karami, M.; Ledesert, B.; Hoteit, N.

2000-01-01

The influence of mineralogy and moisture content on mechanical behaviour of a clay-stone rock is studied by the way of uniaxial and triaxial compression tests and microscopic observations. Some parameters characteristic of phenomena like plasticity and induced anisotropic damage are discussed as a function of these two factors. Rock behaviour becomes more brittle when calcite content grows or when clay or moisture content decreases. At the micro-level, plasticity is induced by slip of clay sheets and induced anisotropic damage appears by growth of oriented microcracks at the interface between grains and matrix. (authors)

Accident analysis of railway transportation of low-level radioactive and hazardous chemical wastes: Application of the /open quotes/Maximum Credible Accident/close quotes/ concept

Energy Technology Data Exchange (ETDEWEB)

Ricci, E.; McLean, R.B.

1988-09-01

The maximum credible accident (MCA) approach to accident analysis places an upper bound on the potential adverse effects of a proposed action by using conservative but simplifying assumptions. It is often used when data are lacking to support a more realistic scenario or when MCA calculations result in acceptable consequences. The MCA approach can also be combined with realistic scenarios to assess potential adverse effects. This report presents a guide for the preparation of transportation accident analyses based on the use of the MCA concept. Rail transportation of contaminated wastes is used as an example. The example is the analysis of the environmental impact of the potential derailment of a train transporting a large shipment of wastes. The shipment is assumed to be contaminated with polychlorinated biphenyls and low-level radioactivities of uranium and technetium. The train is assumed to plunge into a river used as a source of drinking water. The conclusions from the example accident analysis are based on the calculation of the number of foreseeable premature cancer deaths the might result as a consequence of this accident. These calculations are presented, and the reference material forming the basis for all assumptions and calculations is also provided.

Accident analysis of railway transportation of low-level radioactive and hazardous chemical wastes: Application of the /open quotes/Maximum Credible Accident/close quotes/ concept

International Nuclear Information System (INIS)

Ricci, E.; McLean, R.B.

1988-09-01

The maximum credible accident (MCA) approach to accident analysis places an upper bound on the potential adverse effects of a proposed action by using conservative but simplifying assumptions. It is often used when data are lacking to support a more realistic scenario or when MCA calculations result in acceptable consequences. The MCA approach can also be combined with realistic scenarios to assess potential adverse effects. This report presents a guide for the preparation of transportation accident analyses based on the use of the MCA concept. Rail transportation of contaminated wastes is used as an example. The example is the analysis of the environmental impact of the potential derailment of a train transporting a large shipment of wastes. The shipment is assumed to be contaminated with polychlorinated biphenyls and low-level radioactivities of uranium and technetium. The train is assumed to plunge into a river used as a source of drinking water. The conclusions from the example accident analysis are based on the calculation of the number of foreseeable premature cancer deaths the might result as a consequence of this accident. These calculations are presented, and the reference material forming the basis for all assumptions and calculations is also provided

Effective moisture diffusivity, moisture sorption, thermo-physical properties and infrared drying kinetics of germinated paddy

Directory of Open Access Journals (Sweden)

Supawan Tirawanichakul

2014-02-01

Full Text Available Temperature and relative humidity (RH dependence of moisture sorption phenomena for agricultural products provide valuable information related to the thermodynamics of the system. So the equilibrium moisture contents (EMC, effective moisture diffusivity (Deff and thermo-physical properties in terms of void fraction, specific heat capacity, and the apparent density of germinated non-waxy Suphanburi 1 paddy were evaluated. Five commonly cited EMC equations were fitted to the experimental data among temperatures of 40-60°C correlating with RH of 0-90%. The results showed that the modified GAB equation was the best function for describing experimental results while those evaluated thermo-physical properties depended on moisture content. To determine drying kinetics model, the simulated values using Midilli et al. (2002 model and Page’s model was the best fitting to exact drying kinetics values for infrared (IR and hot air (HA drying, respectively. Finally, the Deff value of paddy dried with IR and HA sources were also evaluated and the calculated Deff value of both HA and IR drying was in order of 10-9 m2/s.

Preliminary analysis of the afforestation role in the maximum runoff in Valea Rece Catchment

Directory of Open Access Journals (Sweden)

Mihalcea Andreea

2017-06-01

Full Text Available The aim of this article is to demonstrate the afforestation role in maximum surface runoff. In this way, it was made a comparison of simulated flows in the current conditions of afforestation and the simulated flows in conditions of applying both afforestation and deforestation scenarios in Valea Rece catchment. Through HEC-HMS 4.1 hydrologic modeling software, using the method of unit hydrograph SCS Curve Number, were simulated flow of the river Valea Rece closing section of the basin, where precipitation amounts of 30,50,80,120 mm fallen in intervals of 1.3 to 6 hours on a soil with varying degrees of moisture: dry soil, average soil moisture and high humidity. This was done for the current degree of afforestation basin, for the results from a possible afforestation that would increase the afforestation degree to 80%, and for a possible deforestation that would lead to a degree of afforestation 15 %.

Predicting moisture and economic value of solid forest fuel piles for improving the profitability of bioenergy use

Science.gov (United States)

Lauren, Ari; Kinnunen, Jyrki-Pekko; Sikanen, Lauri

2016-04-01

Bioenergy contributes 26 % of the total energy use in Finland, and 60 % of this is provided by solid forest fuel consisting of small stems and logging residues such as tops, branches, roots and stumps. Typically the logging residues are stored as piles on site before transporting to regional combined heat and power plants for combustion. Profitability of forest fuel use depends on smart control of the feedstock. Fuel moisture, dry matter loss, and the rate of interest during the storing are the key variables affecting the economic value of the fuel. The value increases with drying, but decreases with wetting, dry matter loss and positive rate of interest. We compiled a simple simulation model computing the moisture change, dry matter loss, transportation costs and present value of feedstock piles. The model was used to predict the time of the maximum value of the stock, and to compose feedstock allocation strategies under the question: how should we choose the piles and the combustion time so that total energy yield and the economic value of the energy production is maximized? The question was assessed concerning the demand of the energy plant. The model parameterization was based on field scale studies. The initial moisture, and the rates of daily moisture change and dry matter loss in the feedstock piles depended on the day of the year according to empirical field measurements. Time step of the computation was one day. Effects of pile use timing on the total energy yield and profitability was studied using combinatorial optimization. Results show that the storing increases the pile maximum value if the natural drying onsets soon after the harvesting; otherwise dry matter loss and the capital cost of the storing overcome the benefits gained by drying. Optimized timing of the pile use can improve slightly the profitability, based on the increased total energy yield and because the energy unit based transportation costs decrease when water content in the biomass is

New method measures moisture and true dry mass

International Nuclear Information System (INIS)

Frank, H.

The moisture content of wood can be determined by measuring the nuclear magnetic resonance of free water hydrogen atoms in wood. Nanassy studied NMR curves for six types of wood and obtained the calibration curve by reducing the moisture content in steps by 4% moisture down to ca. 1% moisture and then by gradually wetting the wood. The initial material was fresh wood. For each step he measured the intensity of the free water hydrogen signal. If the sample weight is known the dry matter content (dry weight) and moisture content of the sample can be derived from the measured NMR signal. (J.P.)

Vitrified waste form performance modeling applied to the treatment and disposal of mixed-waste sludge at the Savannah River Site

International Nuclear Information System (INIS)

Whited, A.R.; Fjeld, R.A.

1998-01-01

Vitrification, the conversion of source components into a solid amorphous glass matrix, has emerged as a viable treatment technology for low-level radioactive waste and mixed waste. To dispose of vitrified low-level waste at US Department of Energy facilities, site-specific radiological performance assessments must be conducted to demonstrate that waste glass satisfies performance objectives for environmental protection. More than 2,500 m 3 of F0006-listed low-level mixed-waste sludge stored in the Reactor Materials Department (M-Area) at the Savannah River Site (SRS) is scheduled for vitrification. This study evaluates the feasibility of on-site disposal of vitrified M-Area waste at SRS. Laboratory leaching tests that accelerate the glass corrosion process are currently the best indicators of vitrified waste form durability. A method to incorporate laboratory leaching data into performance assessments is presented. A screening-level performance assessments code is used to model trench disposal of M-Area waste glass. The allowable leach rate for vitrified M-Area waste is determined based on both a maximum radiological dose equivalent of 4 mrem/yr for the drinking water pathway and a maximum uranium concentration of 20 microg/ell in groundwater. The allowable leach rate is compared with published long-term leaching data for a wide range of waste glass compositions and test conditions. This analysis demonstrates that trench disposal of the waste glass is likely to meet applicable performance objectives if the glass is of above average durability compared with the reference set of glasses

Structure of the urban moisture field

International Nuclear Information System (INIS)

Sisterson, D.L.; Dirks, R.A.

1975-01-01

In the 26 July 1974 case study in St. Louis as a part of Project METROMEX, aircraft and surface network stations were used to determine specific humidity and potential temperature patterns near the surface and at two levels within the mixing layer. From the data acquired at these three levels, three-dimensional analyses of the moisture fields in the mixing layer were constructed. The mesoscale dry regions observed throughout the mixing layer correspond to the more impervious surfaces of the urban area. From energy budget considerations, latent heat fluxes are small over these impervious surfaces owing to the large runoff of precipitation and the lack of moisture retention capabilities. Hence, urbanization obviously alters the local energy budget. Surface boundary layer conditions are determined by heat and moisture fluxes. A new internal boundary layer within the city is formed after the breakdown of the radiation inversion in order to compensate for the alteration of sensible heat and latent heat energies. Hence, isolated semistagnant urban air is replenished by moisture only as quickly as evapotranspiration from impervious surfaces will allow. The city surface, therefore, is not a sink of moisture, but rather a reduced source relative to rural areas

Moisture Transfer in Ventilated Facade Structures

Directory of Open Access Journals (Sweden)

Olshevskyi Vyacheslav

2016-01-01

Full Text Available This article discusses the phenomenon of moisture transfer in the designs of ventilated facades (VF. The main ways of moisture transfer are defined. The negative factors connected with moisture accumulation and excessive moistening of insulation are given. The physical processes occurring in the gap of the building envelope due to saturation of air with water vapor are described. The dependence of the intensity of the mass transfer on the air velocity in the layer is considered. Much attention is paid to the selection of the optimum design of the facade, namely a system with or without grooved lines. The dependence of velocity and temperature on the width of the ventilated gap is established empirically for the constructions with open and closed grooves. Expediency of a design without grooves to effectively remove moisture is determined.

Drying and control of moisture content and dimensional changes

Science.gov (United States)

Richard Bergman

2010-01-01

The discussion in this chapter is concerned with moisture content determination, recommended moisture content values, drying methods, methods of calculating dimensional changes, design factors affecting such changes in structures, and moisture content control during transit, storage, and construction. Data on green moisture content, fiber saturation point, shrinkage,...

Digital neutron moisture meter for moisture determination in the cokes and building materials

International Nuclear Information System (INIS)

Chibovski, R.; Igel'ski, A.; Kiyanya, K.; Kiyanya, S.; Mnikh, Eh.; Sledzevski, R.; Verba, V.

1979-01-01

Description is given of the digital neutron moisture gage for measuring water content in coke or in dry building materials. The device can work independently with indication of the results to personnel carrying out control operation and adjustment of the process or as a part of an automated control system with supplying the results of measurements in a form of analogous signals or electric pulses in the preselected code. The moisture gage described consists of two units: measuring probes with containers and the desk with power supply and the system for digital processing of a radiometric signal. The measuring probe consists of the asotopic fast neutrons source; helium proportional counter of slow neutrons and a pulse amplifier. The probe is mounted in the bunker with the material measured and is located inside the protective tube made of the weare-resistant material. To obtain high accuracy of measurements and to obtain the measuring instrument's reading immediately in the units of moisture measurement, the digizal converter circuit for radiometric signals processing is used. The The digital converter circuit cited, can be applied to any calibration dependence of linear type with initial value. The block diagram of the device is given. The device described permits to measure the moisture content in the metallurgy coks and in the building materials in one minute and with the error not more than 0.5% [ru

Impact Of Aerobic Biostabilisation And Biodrying Process Of Municipal Solid Waste On Minimisation Of Waste Deposited In Landfills

Directory of Open Access Journals (Sweden)

Dziedzic Krzysztof

2015-12-01

Full Text Available The article discusses an innovative system used for aerobic biostabilisation and biological drying of solid municipal waste. A mechanical–biological process (MBT of municipal solid waste (MSW treatment were carried out and monitored in 5 bioreactors. A two-stage biological treatment process has been used in the investigation. In the first step an undersize fraction was subjected to the biological stabilisation for a period of 14 days as a result of which there was a decrease of loss on ignition, but not sufficient to fulfill the requirements of MBT technology. In the second stage of a biological treatment has been applied 7-days intensive bio-drying of MSW using sustained high temperatures in bioreactor. The article presents the results of the chemical composition analysis of the undersize fraction and waste after biological drying, and also the results of temperature changes, pH ratio, loss on ignition, moisture content, combustible and volatile matter content, heat of combustion and calorific value of wastes. The mass balance of the MBT of MSW with using the innovative aeration system showed that only 14.5% of waste need to be landfilled, 61.5% could be used for thermal treatment, and nearly 19% being lost in the process as CO2 and H2O.

Solid waste characterization in Ketao, a rural town in Togo, West Africa.

Science.gov (United States)

Edjabou, Maklawe Essonanawe; Møller, Jacob; Christensen, Thomas H

2012-07-01

In Africa the majority of solid waste data is for big cities. Small and rural towns are generally neglected and waste data from these areas are often unavailable, which makes planning a proper solid waste management difficult. This paper presents the results from two waste characterization projects conducted in Kétao, a rural town in Togo during the rainy season and the dry season in 2010. The seasonal variation has a significant impact on the waste stream. The household waste generation rate was estimated at 0.22 kg person(-1) day(-1) in the dry season and 0.42 in the rainy season. Likewise, the waste moisture content was 4% in the dry season while it was 33-63% in the rainy season. The waste consisted mainly of soil and dirt characterized as 'other' (41%), vegetables and putrescibles (38%) and plastic (11%). In addition to these fractions, considerable amounts of material are either recycled or reused locally and do not enter the waste stream. The study suggests that additional recycling is not feasible, but further examination of the degradability of the organic fraction is needed in order to assess whether the residual waste should be composed or landfilled.

Passive microwave remote sensing of soil moisture

International Nuclear Information System (INIS)

Jackson, T.J.; Schmugge, T.J.

1986-01-01

Microwave remote sensing provides a unique capability for direct observation of soil moisture. Remote measurements from space afford the possibility of obtaining frequent, global sampling of soil moisture over a large fraction of the Earth's land surface. Microwave measurements have the benefit of being largely unaffected by cloud cover and variable surface solar illumination, but accurate soil moisture estimates are limited to regions that have either bare soil or low to moderate amounts of vegetation cover. A particular advantage of passive microwave sensors is that in the absence of significant vegetation cover soil moisture is the dominant effect on the received signal. The spatial resolutions of passive microwave soil moisture sensors currently considered for space operation are in the range 10–20 km. The most useful frequency range for soil moisture sensing is 1–5 GHz. System design considerations include optimum choice of frequencies, polarizations, and scanning configurations, based on trade-offs between requirements for high vegetation penetration capability, freedom from electromagnetic interference, manageable antenna size and complexity, and the requirement that a sufficient number of information channels be available to correct for perturbing geophysical effects. This paper outlines the basic principles of the passive microwave technique for soil moisture sensing, and reviews briefly the status of current retrieval methods. Particularly promising are methods for optimally assimilating passive microwave data into hydrologic models. Further studies are needed to investigate the effects on microwave observations of within-footprint spatial heterogeneity of vegetation cover and subsurface soil characteristics, and to assess the limitations imposed by heterogeneity on the retrievability of large-scale soil moisture information from remote observations

Design of Moisture Content Detection System

Science.gov (United States)

Wang, W. C.; Wang, L.

In this paper, a method for measuring the moisture content of grain was presented based on single chip microcomputer and capacitive sensor. The working principle of measuring moisture content is introduced and a concentric cylinder type of capacitive sensor is designed, the signal processing circuits of system are described in details. System is tested in practice and discussions are made on the various factors affecting the capacitive measuring of grain moisture based on the practical experiments, experiment results showed that the system has high measuring accuracy and good controlling capacity.

Soil moisture content with global warming

International Nuclear Information System (INIS)

Vinnikov, K.Ya.

1990-01-01

The potential greenhouse-gas-induced changes in soil moisture, particularly the desiccation of the Northern Hemisphere contents in summer, are discussed. To check the conclusions based on climate models the authors have used long-term measurements of contemporary soil moisture in the USSR and reconstructions of soil moisture for the last two epochs that were warmer than the present, namely, the Holocene optimum, 5,000-6,000 years ago, and the last interglacial, about 125,000 years ago. The analysis shows that there is a considerable disagreement between the model results and the empirical data

Estimation of residual MSW heating value as a function of waste component recycling

International Nuclear Information System (INIS)

Magrinho, Alexandre; Semiao, Viriato

2008-01-01

Recycling of packaging wastes may be compatible with incineration within integrated waste management systems. To study this, a mathematical model is presented to calculate the fraction composition of residual municipal solid waste (MSW) only as a function of the MSW fraction composition at source and recycling fractions of the different waste materials. The application of the model to the Lisbon region yielded results showing that the residual waste fraction composition depends both on the packaging wastes fraction at source and on the ratio between that fraction and the fraction of the same material, packaging and non-packaging, at source. This behaviour determines the variation of the residual waste LHV. For 100% of paper packaging recycling, LHV reduces 4.2% whereas this reduction is of 14.4% for 100% of packaging plastics recycling. For 100% of food waste recovery, LHV increases 36.8% due to the moisture fraction reduction of the residual waste. Additionally the results evidence that the negative impact of recycling paper and plastic packaging on the LHV may be compensated by recycling food waste and glass and metal packaging. This makes packaging materials recycling and food waste recovery compatible strategies with incineration within integrated waste management systems

Effects of heat-moisture treatment reaction conditions on the physicochemical and structural properties of maize starch: moisture and length of heating.

Science.gov (United States)

Sui, Zhongquan; Yao, Tianming; Zhao, Yue; Ye, Xiaoting; Kong, Xiangli; Ai, Lianzhong

2015-04-15

Changes in the properties of normal maize starch (NMS) and waxy maize starch (WMS) after heat-moisture treatment (HMT) under various reaction conditions were investigated. NMS and WMS were adjusted to moisture levels of 20%, 25% and 30% and heated at 100 °C for 2, 4, 8 and 16 h. The results showed that moisture content was the most important factor in determining pasting properties for NMS, whereas the heating length was more important for WMS. Swelling power decreased in NMS but increased in WMS, and while the solubility index decreased for both samples, the changes were largely determined by moisture content. The gelatinisation temperatures of both samples increased with increasing moisture content but remained unchanged with increasing heating length. The Fourier transform infrared (FT-IR) absorbance ratio was affected to different extents by the moisture levels but remained constant with increasing the heating length. The X-ray intensities increased but relative crystallinity decreased to a greater extent with increasing moisture content. This study showed that the levels of moisture content and length of heating had significant impacts on the structural and physicochemical properties of normal and waxy maize starches but to different extents. Copyright © 2014 Elsevier Ltd. All rights reserved.

Neutron moisture measurement in materials

International Nuclear Information System (INIS)

Thony, J.L.

1985-01-01

This method is generally used for soil moisture determination but also for moisture in building materials. After a review of neutron interaction with matter (elastic and inelastic scattering, radiative capture and absorption with emission of charged particles) and of the equipment (source, detector and counting), gravimetric and chemical calibration are described and accuracy of measurement is discussed. 5 refs [fr

Propagation of soil moisture memory into the climate system

Science.gov (United States)

Orth, R.; Seneviratne, S. I.

2012-04-01

Soil moisture is known for its integrative behaviour and resulting memory characteristics. Associated anomalies can persist for weeks or even months into the future, making initial soil moisture an important potential component in weather forecasting. This is particularly crucial given the role of soil moisture for land-atmosphere interactions and its impacts on the water and energy balances on continents. We present here an analysis of the characteristics of soil moisture memory and of its propagation into runoff and evapotranspiration in Europe, based on available measurements from several sites across the continent and expanding a previous analysis focused on soil moisture [1]. We identify the main drivers of soil moisture memory at the analysed sites, as well as their role for the propagation of soil moisture persistence into runoff and evapotranspiration memory characteristics. We focus on temporal and spatial variations in these relationships and identify seasonal and latitudinal differences in the persistence of soil moisture, evapotranspiration and runoff. Finally, we assess the role of these persistence characteristics for the development of agricultural and hydrological droughts. [1] Orth and Seneviratne: Analysis of soil moisture memory from observations in Europe; submitted to J. Geophysical Research.